2876 files changed, 255663 insertions, 76211 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 08011dc8c7a6..efe38eb25301 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1,1318 +1,41 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_ARCH_ALPINE) += \
-	alpine-db.dtb
-dtb-$(CONFIG_MACH_ARTPEC6) += \
-	artpec6-devboard.dtb
-dtb-$(CONFIG_MACH_ASM9260) += \
-	alphascale-asm9260-devkit.dtb
-# Keep at91 dtb files sorted alphabetically for each SoC
-dtb-$(CONFIG_SOC_AT91RM9200) += \
-	at91rm9200ek.dtb \
-	mpa1600.dtb
-dtb-$(CONFIG_SOC_AT91SAM9) += \
-	animeo_ip.dtb \
-	at91-qil_a9260.dtb \
-	aks-cdu.dtb \
-	ethernut5.dtb \
-	evk-pro3.dtb \
-	tny_a9260.dtb \
-	usb_a9260.dtb \
-	at91sam9260ek.dtb \
-	at91sam9261ek.dtb \
-	at91sam9263ek.dtb \
-	at91-sam9_l9260.dtb \
-	tny_a9263.dtb \
-	usb_a9263.dtb \
-	at91-foxg20.dtb \
-	at91-kizbox.dtb \
-	at91sam9g20ek.dtb \
-	at91sam9g20ek_2mmc.dtb \
-	tny_a9g20.dtb \
-	usb_a9g20.dtb \
-	usb_a9g20_lpw.dtb \
-	at91sam9m10g45ek.dtb \
-	pm9g45.dtb \
-	at91sam9n12ek.dtb \
-	at91sam9rlek.dtb \
-	at91-ariag25.dtb \
-	at91-ariettag25.dtb \
-	at91-cosino_mega2560.dtb \
-	at91-kizboxmini.dtb \
-	at91-wb45n.dtb \
-	at91sam9g15ek.dtb \
-	at91sam9g25ek.dtb \
-	at91sam9g35ek.dtb \
-	at91sam9x25ek.dtb \
-	at91sam9x35ek.dtb
-dtb-$(CONFIG_SOC_SAM_V7) += \
-	at91-kizbox2-2.dtb \
-	at91-kizbox3-hs.dtb \
-	at91-nattis-2-natte-2.dtb \
-	at91-sama5d27_som1_ek.dtb \
-	at91-sama5d2_ptc_ek.dtb \
-	at91-sama5d2_xplained.dtb \
-	at91-sama5d3_xplained.dtb \
-	at91-dvk_som60.dtb \
-	at91-gatwick.dtb \
-	at91-tse850-3.dtb \
-	at91-wb50n.dtb \
-	sama5d31ek.dtb \
-	sama5d33ek.dtb \
-	sama5d34ek.dtb \
-	sama5d35ek.dtb \
-	sama5d36ek.dtb \
-	sama5d36ek_cmp.dtb \
-	at91-sama5d4_ma5d4evk.dtb \
-	at91-sama5d4_xplained.dtb \
-	at91-sama5d4ek.dtb \
-	at91-vinco.dtb
-dtb-$(CONFIG_ARCH_ATLAS6) += \
-	atlas6-evb.dtb
-dtb-$(CONFIG_ARCH_ATLAS7) += \
-	atlas7-evb.dtb
-dtb-$(CONFIG_ARCH_AXXIA) += \
-	axm5516-amarillo.dtb
-dtb-$(CONFIG_ARCH_BCM2835) += \
-	bcm2835-rpi-b.dtb \
-	bcm2835-rpi-a.dtb \
-	bcm2835-rpi-b-rev2.dtb \
-	bcm2835-rpi-b-plus.dtb \
-	bcm2835-rpi-a-plus.dtb \
-	bcm2835-rpi-cm1-io1.dtb \
-	bcm2836-rpi-2-b.dtb \
-	bcm2837-rpi-3-a-plus.dtb \
-	bcm2837-rpi-3-b.dtb \
-	bcm2837-rpi-3-b-plus.dtb \
-	bcm2837-rpi-cm3-io3.dtb \
-	bcm2711-rpi-4-b.dtb \
-	bcm2835-rpi-zero.dtb \
-	bcm2835-rpi-zero-w.dtb
-dtb-$(CONFIG_ARCH_BCM_5301X) += \
-	bcm4708-asus-rt-ac56u.dtb \
-	bcm4708-asus-rt-ac68u.dtb \
-	bcm4708-buffalo-wzr-1750dhp.dtb \
-	bcm4708-linksys-ea6300-v1.dtb \
-	bcm4708-linksys-ea6500-v2.dtb \
-	bcm4708-luxul-xap-1510.dtb \
-	bcm4708-luxul-xwc-1000.dtb \
-	bcm4708-netgear-r6250.dtb \
-	bcm4708-netgear-r6300-v2.dtb \
-	bcm4708-smartrg-sr400ac.dtb \
-	bcm47081-asus-rt-n18u.dtb \
-	bcm47081-buffalo-wzr-600dhp2.dtb \
-	bcm47081-buffalo-wzr-900dhp.dtb \
-	bcm47081-luxul-xap-1410.dtb \
-	bcm47081-luxul-xwr-1200.dtb \
-	bcm47081-tplink-archer-c5-v2.dtb \
-	bcm4709-asus-rt-ac87u.dtb \
-	bcm4709-buffalo-wxr-1900dhp.dtb \
-	bcm4709-linksys-ea9200.dtb \
-	bcm4709-netgear-r7000.dtb \
-	bcm4709-netgear-r8000.dtb \
-	bcm4709-tplink-archer-c9-v1.dtb \
-	bcm47094-dlink-dir-885l.dtb \
-	bcm47094-linksys-panamera.dtb \
-	bcm47094-luxul-abr-4500.dtb \
-	bcm47094-luxul-xap-1610.dtb \
-	bcm47094-luxul-xbr-4500.dtb \
-	bcm47094-luxul-xwc-2000.dtb \
-	bcm47094-luxul-xwr-3100.dtb \
-	bcm47094-luxul-xwr-3150-v1.dtb \
-	bcm47094-netgear-r8500.dtb \
-	bcm47094-phicomm-k3.dtb \
-	bcm94708.dtb \
-	bcm94709.dtb \
-	bcm953012er.dtb \
-	bcm953012hr.dtb \
-	bcm953012k.dtb
-dtb-$(CONFIG_ARCH_BCM_53573) += \
-	bcm47189-luxul-xap-1440.dtb \
-	bcm47189-luxul-xap-810.dtb \
-	bcm47189-tenda-ac9.dtb \
-	bcm947189acdbmr.dtb
-dtb-$(CONFIG_ARCH_BCM_63XX) += \
-	bcm963138dvt.dtb
-dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
-	bcm911360_entphn.dtb \
-	bcm911360k.dtb \
-	bcm958300k.dtb \
-	bcm958305k.dtb
-dtb-$(CONFIG_ARCH_BCM_HR2) += \
-	bcm53340-ubnt-unifi-switch8.dtb
-dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
-	bcm28155-ap.dtb \
-	bcm21664-garnet.dtb \
-	bcm23550-sparrow.dtb
-dtb-$(CONFIG_ARCH_BCM_NSP) += \
-	bcm958522er.dtb \
-	bcm958525er.dtb \
-	bcm958525xmc.dtb \
-	bcm958622hr.dtb \
-	bcm958623hr.dtb \
-	bcm958625hr.dtb \
-	bcm988312hr.dtb \
-	bcm958625k.dtb
-dtb-$(CONFIG_ARCH_BERLIN) += \
-	berlin2-sony-nsz-gs7.dtb \
-	berlin2cd-google-chromecast.dtb \
-	berlin2cd-valve-steamlink.dtb \
-	berlin2q-marvell-dmp.dtb
-dtb-$(CONFIG_ARCH_BRCMSTB) += \
-	bcm7445-bcm97445svmb.dtb
-dtb-$(CONFIG_ARCH_CLPS711X) += \
-	ep7211-edb7211.dtb
-dtb-$(CONFIG_ARCH_DAVINCI) += \
-	da850-lcdk.dtb \
-	da850-enbw-cmc.dtb \
-	da850-evm.dtb \
-	da850-lego-ev3.dtb
-dtb-$(CONFIG_ARCH_DIGICOLOR) += \
-	cx92755_equinox.dtb
-dtb-$(CONFIG_ARCH_EFM32) += \
-	efm32gg-dk3750.dtb
-dtb-$(CONFIG_ARCH_EXYNOS3) += \
-	exynos3250-artik5-eval.dtb \
-	exynos3250-monk.dtb \
-	exynos3250-rinato.dtb
-dtb-$(CONFIG_ARCH_EXYNOS4) += \
-	exynos4210-origen.dtb \
-	exynos4210-smdkv310.dtb \
-	exynos4210-trats.dtb \
-	exynos4210-universal_c210.dtb \
-	exynos4412-i9300.dtb \
-	exynos4412-i9305.dtb \
-	exynos4412-itop-elite.dtb \
-	exynos4412-n710x.dtb \
-	exynos4412-odroidu3.dtb \
-	exynos4412-odroidx.dtb \
-	exynos4412-odroidx2.dtb \
-	exynos4412-origen.dtb \
-	exynos4412-smdk4412.dtb \
-	exynos4412-tiny4412.dtb \
-	exynos4412-trats2.dtb
-dtb-$(CONFIG_ARCH_EXYNOS5) += \
-	exynos5250-arndale.dtb \
-	exynos5250-smdk5250.dtb \
-	exynos5250-snow.dtb \
-	exynos5250-snow-rev5.dtb \
-	exynos5250-spring.dtb \
-	exynos5260-xyref5260.dtb \
-	exynos5410-odroidxu.dtb \
-	exynos5410-smdk5410.dtb \
-	exynos5420-arndale-octa.dtb \
-	exynos5420-peach-pit.dtb \
-	exynos5420-smdk5420.dtb \
-	exynos5422-odroidhc1.dtb \
-	exynos5422-odroidxu3.dtb \
-	exynos5422-odroidxu3-lite.dtb \
-	exynos5422-odroidxu4.dtb \
-	exynos5800-peach-pi.dtb
-dtb-$(CONFIG_ARCH_GEMINI) += \
-	gemini-dlink-dir-685.dtb \
-	gemini-dlink-dns-313.dtb \
-	gemini-nas4220b.dtb \
-	gemini-rut1xx.dtb \
-	gemini-sl93512r.dtb \
-	gemini-sq201.dtb \
-	gemini-wbd111.dtb \
-	gemini-wbd222.dtb
-dtb-$(CONFIG_ARCH_HI3xxx) += \
-	hi3620-hi4511.dtb
-dtb-$(CONFIG_ARCH_HIGHBANK) += \
-	highbank.dtb \
-	ecx-2000.dtb
-dtb-$(CONFIG_ARCH_HIP01) += \
-	hip01-ca9x2.dtb
-dtb-$(CONFIG_ARCH_HIP04) += \
-	hip04-d01.dtb
-dtb-$(CONFIG_ARCH_HISI) += \
-	hi3519-demb.dtb
-dtb-$(CONFIG_ARCH_HIX5HD2) += \
-	hisi-x5hd2-dkb.dtb
-dtb-$(CONFIG_ARCH_INTEGRATOR) += \
-	integratorap.dtb \
-	integratorcp.dtb
-dtb-$(CONFIG_ARCH_IXP4XX) += \
-	intel-ixp42x-linksys-nslu2.dtb \
-	intel-ixp43x-gateworks-gw2358.dtb
-dtb-$(CONFIG_ARCH_KEYSTONE) += \
-	keystone-k2hk-evm.dtb \
-	keystone-k2l-evm.dtb \
-	keystone-k2e-evm.dtb \
-	keystone-k2g-evm.dtb \
-	keystone-k2g-ice.dtb
-dtb-$(CONFIG_MACH_KIRKWOOD) += \
-	kirkwood-b3.dtb \
-	kirkwood-blackarmor-nas220.dtb \
-	kirkwood-cloudbox.dtb \
-	kirkwood-d2net.dtb \
-	kirkwood-db-88f6281.dtb \
-	kirkwood-db-88f6282.dtb \
-	kirkwood-dir665.dtb \
-	kirkwood-dns320.dtb \
-	kirkwood-dns325.dtb \
-	kirkwood-dockstar.dtb \
-	kirkwood-dreamplug.dtb \
-	kirkwood-ds109.dtb \
-	kirkwood-ds110jv10.dtb \
-	kirkwood-ds111.dtb \
-	kirkwood-ds112.dtb \
-	kirkwood-ds209.dtb \
-	kirkwood-ds210.dtb \
-	kirkwood-ds212.dtb \
-	kirkwood-ds212j.dtb \
-	kirkwood-ds409.dtb \
-	kirkwood-ds409slim.dtb \
-	kirkwood-ds411.dtb \
-	kirkwood-ds411j.dtb \
-	kirkwood-ds411slim.dtb \
-	kirkwood-goflexnet.dtb \
-	kirkwood-guruplug-server-plus.dtb \
-	kirkwood-ib62x0.dtb \
-	kirkwood-iconnect.dtb \
-	kirkwood-iomega_ix2_200.dtb \
-	kirkwood-is2.dtb \
-	kirkwood-km_kirkwood.dtb \
-	kirkwood-laplug.dtb \
-	kirkwood-linkstation-lsqvl.dtb \
-	kirkwood-linkstation-lsvl.dtb \
-	kirkwood-linkstation-lswsxl.dtb \
-	kirkwood-linkstation-lswvl.dtb \
-	kirkwood-linkstation-lswxl.dtb \
-	kirkwood-linksys-viper.dtb \
-	kirkwood-lschlv2.dtb \
-	kirkwood-lsxhl.dtb \
-	kirkwood-mplcec4.dtb \
-	kirkwood-mv88f6281gtw-ge.dtb \
-	kirkwood-nas2big.dtb \
-	kirkwood-net2big.dtb \
-	kirkwood-net5big.dtb \
-	kirkwood-netgear_readynas_duo_v2.dtb \
-	kirkwood-netgear_readynas_nv+_v2.dtb \
-	kirkwood-ns2.dtb \
-	kirkwood-ns2lite.dtb \
-	kirkwood-ns2max.dtb \
-	kirkwood-ns2mini.dtb \
-	kirkwood-nsa310.dtb \
-	kirkwood-nsa310a.dtb \
-	kirkwood-nsa320.dtb \
-	kirkwood-nsa325.dtb \
-	kirkwood-openblocks_a6.dtb \
-	kirkwood-openblocks_a7.dtb \
-	kirkwood-openrd-base.dtb \
-	kirkwood-openrd-client.dtb \
-	kirkwood-openrd-ultimate.dtb \
-	kirkwood-pogo_e02.dtb \
-	kirkwood-pogoplug-series-4.dtb \
-	kirkwood-rd88f6192.dtb \
-	kirkwood-rd88f6281-z0.dtb \
-	kirkwood-rd88f6281-a.dtb \
-	kirkwood-rs212.dtb \
-	kirkwood-rs409.dtb \
-	kirkwood-rs411.dtb \
-	kirkwood-sheevaplug.dtb \
-	kirkwood-sheevaplug-esata.dtb \
-	kirkwood-t5325.dtb \
-	kirkwood-topkick.dtb \
-	kirkwood-ts219-6281.dtb \
-	kirkwood-ts219-6282.dtb \
-	kirkwood-ts419-6281.dtb \
-	kirkwood-ts419-6282.dtb
-dtb-$(CONFIG_ARCH_LPC18XX) += \
-	lpc4337-ciaa.dtb \
-	lpc4350-hitex-eval.dtb \
-	lpc4357-ea4357-devkit.dtb \
-	lpc4357-myd-lpc4357.dtb
-dtb-$(CONFIG_ARCH_LPC32XX) += \
-	lpc3250-ea3250.dtb \
-	lpc3250-phy3250.dtb
-dtb-$(CONFIG_ARCH_NPCM7XX) += \
-	nuvoton-npcm750-evb.dtb
-dtb-$(CONFIG_MACH_MESON6) += \
-	meson6-atv1200.dtb
-dtb-$(CONFIG_MACH_MESON8) += \
-	meson8-minix-neo-x8.dtb \
-	meson8b-ec100.dtb \
-	meson8b-mxq.dtb \
-	meson8b-odroidc1.dtb \
-	meson8m2-mxiii-plus.dtb
-dtb-$(CONFIG_ARCH_MMP) += \
-	pxa168-aspenite.dtb \
-	pxa910-dkb.dtb \
-	mmp2-brownstone.dtb \
-	mmp2-olpc-xo-1-75.dtb \
-	mmp3-dell-ariel.dtb
-dtb-$(CONFIG_ARCH_MPS2) += \
-	mps2-an385.dtb \
-	mps2-an399.dtb
-dtb-$(CONFIG_ARCH_MOXART) += \
-	moxart-uc7112lx.dtb
-dtb-$(CONFIG_SOC_IMX1) += \
-	imx1-ads.dtb \
-	imx1-apf9328.dtb
-dtb-$(CONFIG_SOC_IMX25) += \
-	imx25-eukrea-mbimxsd25-baseboard.dtb \
-	imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb \
-	imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb \
-	imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb \
-	imx25-karo-tx25.dtb \
-	imx25-pdk.dtb
-dtb-$(CONFIG_SOC_IMX27) += \
-	imx27-apf27.dtb \
-	imx27-apf27dev.dtb \
-	imx27-eukrea-mbimxsd27-baseboard.dtb \
-	imx27-pdk.dtb \
-	imx27-phytec-phycore-rdk.dtb \
-	imx27-phytec-phycard-s-rdk.dtb
-dtb-$(CONFIG_SOC_IMX31) += \
-	imx31-bug.dtb \
-	imx31-lite.dtb
-dtb-$(CONFIG_SOC_IMX35) += \
-	imx35-eukrea-mbimxsd35-baseboard.dtb \
-	imx35-pdk.dtb
-dtb-$(CONFIG_SOC_IMX50) += \
-	imx50-evk.dtb \
-	imx50-kobo-aura.dtb
-dtb-$(CONFIG_SOC_IMX51) += \
-	imx51-apf51.dtb \
-	imx51-apf51dev.dtb \
-	imx51-babbage.dtb \
-	imx51-digi-connectcore-jsk.dtb \
-	imx51-eukrea-mbimxsd51-baseboard.dtb \
-	imx51-ts4800.dtb \
-	imx51-zii-rdu1.dtb \
-	imx51-zii-scu2-mezz.dtb \
-	imx51-zii-scu3-esb.dtb
-dtb-$(CONFIG_SOC_IMX53) += \
-	imx53-ard.dtb \
-	imx53-cx9020.dtb \
-	imx53-kp-ddc.dtb \
-	imx53-kp-hsc.dtb \
-	imx53-m53evk.dtb \
-	imx53-m53menlo.dtb \
-	imx53-mba53.dtb \
-	imx53-ppd.dtb \
-	imx53-qsb.dtb \
-	imx53-qsrb.dtb \
-	imx53-smd.dtb \
-	imx53-tx53-x03x.dtb \
-	imx53-tx53-x13x.dtb \
-	imx53-usbarmory.dtb \
-	imx53-voipac-bsb.dtb
-dtb-$(CONFIG_SOC_IMX6Q) += \
-	imx6dl-apf6dev.dtb \
-	imx6dl-aristainetos_4.dtb \
-	imx6dl-aristainetos_7.dtb \
-	imx6dl-aristainetos2_4.dtb \
-	imx6dl-aristainetos2_7.dtb \
-	imx6dl-colibri-eval-v3.dtb \
-	imx6dl-cubox-i.dtb \
-	imx6dl-cubox-i-emmc-som-v15.dtb \
-	imx6dl-cubox-i-som-v15.dtb \
-	imx6dl-dfi-fs700-m60.dtb \
-	imx6dl-eckelmann-ci4x10.dtb \
-	imx6dl-emcon-avari.dtb \
-	imx6dl-gw51xx.dtb \
-	imx6dl-gw52xx.dtb \
-	imx6dl-gw53xx.dtb \
-	imx6dl-gw54xx.dtb \
-	imx6dl-gw551x.dtb \
-	imx6dl-gw552x.dtb \
-	imx6dl-gw553x.dtb \
-	imx6dl-gw560x.dtb \
-	imx6dl-gw5903.dtb \
-	imx6dl-gw5904.dtb \
-	imx6dl-hummingboard.dtb \
-	imx6dl-hummingboard-emmc-som-v15.dtb \
-	imx6dl-hummingboard-som-v15.dtb \
-	imx6dl-hummingboard2.dtb \
-	imx6dl-hummingboard2-emmc-som-v15.dtb \
-	imx6dl-hummingboard2-som-v15.dtb \
-	imx6dl-icore.dtb \
-	imx6dl-icore-mipi.dtb \
-	imx6dl-icore-rqs.dtb \
-	imx6dl-mamoj.dtb \
-	imx6dl-nit6xlite.dtb \
-	imx6dl-nitrogen6x.dtb \
-	imx6dl-phytec-mira-rdk-nand.dtb \
-	imx6dl-phytec-pbab01.dtb \
-	imx6dl-rex-basic.dtb \
-	imx6dl-riotboard.dtb \
-	imx6dl-sabreauto.dtb \
-	imx6dl-sabrelite.dtb \
-	imx6dl-sabresd.dtb \
-	imx6dl-savageboard.dtb \
-	imx6dl-ts4900.dtb \
-	imx6dl-ts7970.dtb \
-	imx6dl-tx6dl-comtft.dtb \
-	imx6dl-tx6s-8034.dtb \
-	imx6dl-tx6s-8034-mb7.dtb \
-	imx6dl-tx6s-8035.dtb \
-	imx6dl-tx6s-8035-mb7.dtb \
-	imx6dl-tx6u-801x.dtb \
-	imx6dl-tx6u-80xx-mb7.dtb \
-	imx6dl-tx6u-8033.dtb \
-	imx6dl-tx6u-8033-mb7.dtb \
-	imx6dl-tx6u-811x.dtb \
-	imx6dl-tx6u-81xx-mb7.dtb \
-	imx6dl-udoo.dtb \
-	imx6dl-wandboard.dtb \
-	imx6dl-wandboard-revb1.dtb \
-	imx6dl-wandboard-revd1.dtb \
-	imx6dl-yapp4-draco.dtb \
-	imx6dl-yapp4-hydra.dtb \
-	imx6dl-yapp4-ursa.dtb \
-	imx6q-apalis-eval.dtb \
-	imx6q-apalis-ixora.dtb \
-	imx6q-apalis-ixora-v1.1.dtb \
-	imx6q-apf6dev.dtb \
-	imx6q-arm2.dtb \
-	imx6q-b450v3.dtb \
-	imx6q-b650v3.dtb \
-	imx6q-b850v3.dtb \
-	imx6q-cm-fx6.dtb \
-	imx6q-cubox-i.dtb \
-	imx6q-cubox-i-emmc-som-v15.dtb \
-	imx6q-cubox-i-som-v15.dtb \
-	imx6q-dfi-fs700-m60.dtb \
-	imx6q-dhcom-pdk2.dtb \
-	imx6q-display5-tianma-tm070-1280x768.dtb \
-	imx6q-dmo-edmqmx6.dtb \
-	imx6q-dms-ba16.dtb \
-	imx6q-emcon-avari.dtb \
-	imx6q-evi.dtb \
-	imx6q-gk802.dtb \
-	imx6q-gw51xx.dtb \
-	imx6q-gw52xx.dtb \
-	imx6q-gw53xx.dtb \
-	imx6q-gw5400-a.dtb \
-	imx6q-gw54xx.dtb \
-	imx6q-gw551x.dtb \
-	imx6q-gw552x.dtb \
-	imx6q-gw553x.dtb \
-	imx6q-gw560x.dtb \
-	imx6q-gw5903.dtb \
-	imx6q-gw5904.dtb \
-	imx6q-h100.dtb \
-	imx6q-hummingboard.dtb \
-	imx6q-hummingboard-emmc-som-v15.dtb \
-	imx6q-hummingboard-som-v15.dtb \
-	imx6q-hummingboard2.dtb \
-	imx6q-hummingboard2-emmc-som-v15.dtb \
-	imx6q-hummingboard2-som-v15.dtb \
-	imx6q-icore.dtb \
-	imx6q-icore-mipi.dtb \
-	imx6q-icore-ofcap10.dtb \
-	imx6q-icore-ofcap12.dtb \
-	imx6q-icore-rqs.dtb \
-	imx6q-kp-tpc.dtb \
-	imx6q-marsboard.dtb \
-	imx6q-mccmon6.dtb \
-	imx6q-nitrogen6x.dtb \
-	imx6q-nitrogen6_max.dtb \
-	imx6q-nitrogen6_som2.dtb \
-	imx6q-novena.dtb \
-	imx6q-phytec-mira-rdk-emmc.dtb \
-	imx6q-phytec-mira-rdk-nand.dtb \
-	imx6q-phytec-pbab01.dtb \
-	imx6q-pistachio.dtb \
-	imx6q-rex-pro.dtb \
-	imx6q-sabreauto.dtb \
-	imx6q-sabrelite.dtb \
-	imx6q-sabresd.dtb \
-	imx6q-savageboard.dtb \
-	imx6q-sbc6x.dtb \
-	imx6q-tbs2910.dtb \
-	imx6q-ts4900.dtb \
-	imx6q-ts7970.dtb \
-	imx6q-tx6q-1010.dtb \
-	imx6q-tx6q-1010-comtft.dtb \
-	imx6q-tx6q-1020.dtb \
-	imx6q-tx6q-1020-comtft.dtb \
-	imx6q-tx6q-1036.dtb \
-	imx6q-tx6q-1036-mb7.dtb \
-	imx6q-tx6q-10x0-mb7.dtb \
-	imx6q-tx6q-1110.dtb \
-	imx6q-tx6q-11x0-mb7.dtb \
-	imx6q-udoo.dtb \
-	imx6q-utilite-pro.dtb \
-	imx6q-var-dt6customboard.dtb \
-	imx6q-wandboard.dtb \
-	imx6q-wandboard-revb1.dtb \
-	imx6q-wandboard-revd1.dtb \
-	imx6q-zii-rdu2.dtb \
-	imx6qp-nitrogen6_max.dtb \
-	imx6qp-nitrogen6_som2.dtb \
-	imx6qp-phytec-mira-rdk-nand.dtb \
-	imx6qp-sabreauto.dtb \
-	imx6qp-sabresd.dtb \
-	imx6qp-tx6qp-8037.dtb \
-	imx6qp-tx6qp-8037-mb7.dtb \
-	imx6qp-tx6qp-8137.dtb \
-	imx6qp-tx6qp-8137-mb7.dtb \
-	imx6qp-wandboard-revd1.dtb \
-	imx6qp-zii-rdu2.dtb
-dtb-$(CONFIG_SOC_IMX6SL) += \
-	imx6sl-evk.dtb \
-	imx6sl-warp.dtb
-dtb-$(CONFIG_SOC_IMX6SLL) += \
-	imx6sll-evk.dtb \
-	imx6sll-kobo-clarahd.dtb
-dtb-$(CONFIG_SOC_IMX6SX) += \
-	imx6sx-nitrogen6sx.dtb \
-	imx6sx-sabreauto.dtb \
-	imx6sx-sdb-reva.dtb \
-	imx6sx-sdb-sai.dtb \
-	imx6sx-sdb.dtb \
-	imx6sx-softing-vining-2000.dtb \
-	imx6sx-udoo-neo-basic.dtb \
-	imx6sx-udoo-neo-extended.dtb \
-	imx6sx-udoo-neo-full.dtb
-dtb-$(CONFIG_SOC_IMX6UL) += \
-	imx6ul-14x14-evk.dtb \
-	imx6ul-ccimx6ulsbcexpress.dtb \
-	imx6ul-ccimx6ulsbcpro.dtb \
-	imx6ul-geam.dtb \
-	imx6ul-isiot-emmc.dtb \
-	imx6ul-isiot-nand.dtb \
-	imx6ul-kontron-n6310-s.dtb \
-	imx6ul-kontron-n6310-s-43.dtb \
-	imx6ul-liteboard.dtb \
-	imx6ul-opos6uldev.dtb \
-	imx6ul-pico-hobbit.dtb \
-	imx6ul-pico-pi.dtb \
-	imx6ul-phytec-segin-ff-rdk-nand.dtb \
-	imx6ul-tx6ul-0010.dtb \
-	imx6ul-tx6ul-0011.dtb \
-	imx6ul-tx6ul-mainboard.dtb \
-	imx6ull-14x14-evk.dtb \
-	imx6ull-colibri-eval-v3.dtb \
-	imx6ull-colibri-wifi-eval-v3.dtb \
-	imx6ull-opos6uldev.dtb \
-	imx6ull-phytec-segin-ff-rdk-nand.dtb \
-	imx6ull-phytec-segin-ff-rdk-emmc.dtb \
-	imx6ull-phytec-segin-lc-rdk-nand.dtb \
-	imx6ulz-14x14-evk.dtb
-dtb-$(CONFIG_SOC_IMX7D) += \
-	imx7d-cl-som-imx7.dtb \
-	imx7d-colibri-emmc-eval-v3.dtb \
-	imx7d-colibri-eval-v3.dtb \
-	imx7d-mba7.dtb \
-	imx7d-meerkat96.dtb \
-	imx7d-nitrogen7.dtb \
-	imx7d-pico-hobbit.dtb \
-	imx7d-pico-pi.dtb \
-	imx7d-sbc-imx7.dtb \
-	imx7d-sdb.dtb \
-	imx7d-sdb-reva.dtb \
-	imx7d-sdb-sht11.dtb \
-	imx7d-zii-rmu2.dtb \
-	imx7d-zii-rpu2.dtb \
-	imx7s-colibri-eval-v3.dtb \
-	imx7s-mba7.dtb \
-	imx7s-warp.dtb
-dtb-$(CONFIG_SOC_IMX7ULP) += \
-	imx7ulp-evk.dtb
-dtb-$(CONFIG_SOC_LS1021A) += \
-	ls1021a-moxa-uc-8410a.dtb \
-	ls1021a-qds.dtb \
-	ls1021a-tsn.dtb \
-	ls1021a-twr.dtb
-dtb-$(CONFIG_SOC_VF610) += \
-	vf500-colibri-eval-v3.dtb \
-	vf610-bk4.dtb \
-	vf610-colibri-eval-v3.dtb \
-	vf610m4-colibri.dtb \
-	vf610-cosmic.dtb \
-	vf610m4-cosmic.dtb \
-	vf610-twr.dtb \
-	vf610-zii-cfu1.dtb \
-	vf610-zii-dev-rev-b.dtb \
-	vf610-zii-dev-rev-c.dtb \
-	vf610-zii-scu4-aib.dtb \
-	vf610-zii-spb4.dtb \
-	vf610-zii-ssmb-dtu.dtb \
-	vf610-zii-ssmb-spu3.dtb
-dtb-$(CONFIG_ARCH_MXS) += \
-	imx23-evk.dtb \
-	imx23-olinuxino.dtb \
-	imx23-sansa.dtb \
-	imx23-stmp378x_devb.dtb \
-	imx23-xfi3.dtb \
-	imx28-apf28.dtb \
-	imx28-apf28dev.dtb \
-	imx28-apx4devkit.dtb \
-	imx28-cfa10036.dtb \
-	imx28-cfa10037.dtb \
-	imx28-cfa10049.dtb \
-	imx28-cfa10055.dtb \
-	imx28-cfa10056.dtb \
-	imx28-cfa10057.dtb \
-	imx28-cfa10058.dtb \
-	imx28-duckbill-2-485.dtb \
-	imx28-duckbill-2.dtb \
-	imx28-duckbill-2-enocean.dtb \
-	imx28-duckbill-2-spi.dtb \
-	imx28-duckbill.dtb \
-	imx28-eukrea-mbmx283lc.dtb \
-	imx28-eukrea-mbmx287lc.dtb \
-	imx28-evk.dtb \
-	imx28-m28cu3.dtb \
-	imx28-m28evk.dtb \
-	imx28-sps1.dtb \
-	imx28-ts4600.dtb \
-	imx28-tx28.dtb
-dtb-$(CONFIG_ARCH_NOMADIK) += \
-	ste-nomadik-s8815.dtb \
-	ste-nomadik-nhk15.dtb
-dtb-$(CONFIG_ARCH_NSPIRE) += \
-	nspire-cx.dtb \
-	nspire-tp.dtb \
-	nspire-clp.dtb
-dtb-$(CONFIG_ARCH_OMAP2) += \
-	omap2420-h4.dtb \
-	omap2420-n800.dtb \
-	omap2420-n810.dtb \
-	omap2420-n810-wimax.dtb \
-	omap2430-sdp.dtb
-dtb-$(CONFIG_ARCH_OMAP3) += \
-	am3517-craneboard.dtb \
-	am3517-evm.dtb \
-	am3517_mt_ventoux.dtb \
-	logicpd-torpedo-37xx-devkit.dtb \
-	logicpd-som-lv-37xx-devkit.dtb \
-	omap3430-sdp.dtb \
-	omap3-beagle.dtb \
-	omap3-beagle-xm.dtb \
-	omap3-beagle-xm-ab.dtb \
-	omap3-cm-t3517.dtb \
-	omap3-cm-t3530.dtb \
-	omap3-cm-t3730.dtb \
-	omap3-devkit8000.dtb \
-	omap3-devkit8000-lcd43.dtb \
-	omap3-devkit8000-lcd70.dtb \
-	omap3-evm.dtb \
-	omap3-evm-37xx.dtb \
-	omap3-gta04a3.dtb \
-	omap3-gta04a4.dtb \
-	omap3-gta04a5.dtb \
-	omap3-gta04a5one.dtb \
-	omap3-ha.dtb \
-	omap3-ha-lcd.dtb \
-	omap3-igep0020.dtb \
-	omap3-igep0020-rev-f.dtb \
-	omap3-igep0030.dtb \
-	omap3-igep0030-rev-g.dtb \
-	omap3-ldp.dtb \
-	omap3-lilly-dbb056.dtb \
-	omap3-n900.dtb \
-	omap3-n9.dtb \
-	omap3-n950.dtb \
-	omap3-overo-alto35.dtb \
-	omap3-overo-chestnut43.dtb \
-	omap3-overo-gallop43.dtb \
-	omap3-overo-palo35.dtb \
-	omap3-overo-palo43.dtb \
-	omap3-overo-storm-alto35.dtb \
-	omap3-overo-storm-chestnut43.dtb \
-	omap3-overo-storm-gallop43.dtb \
-	omap3-overo-storm-palo35.dtb \
-	omap3-overo-storm-palo43.dtb \
-	omap3-overo-storm-summit.dtb \
-	omap3-overo-storm-tobi.dtb \
-	omap3-overo-storm-tobiduo.dtb \
-	omap3-overo-summit.dtb \
-	omap3-overo-tobi.dtb \
-	omap3-overo-tobiduo.dtb \
-	omap3-pandora-600mhz.dtb \
-	omap3-pandora-1ghz.dtb \
-	omap3-sbc-t3517.dtb \
-	omap3-sbc-t3530.dtb \
-	omap3-sbc-t3730.dtb \
-	omap3-sniper.dtb \
-	omap3-thunder.dtb \
-	omap3-zoom3.dtb
-dtb-$(CONFIG_SOC_TI81XX) += \
-	am3874-iceboard.dtb \
-	dm8148-evm.dtb \
-	dm8148-t410.dtb \
-	dm8168-evm.dtb \
-	dra62x-j5eco-evm.dtb
-dtb-$(CONFIG_SOC_AM33XX) += \
-	am335x-baltos-ir2110.dtb \
-	am335x-baltos-ir3220.dtb \
-	am335x-baltos-ir5221.dtb \
-	am335x-base0033.dtb \
-	am335x-bone.dtb \
-	am335x-boneblack.dtb \
-	am335x-boneblack-wireless.dtb \
-	am335x-boneblue.dtb \
-	am335x-bonegreen.dtb \
-	am335x-bonegreen-wireless.dtb \
-	am335x-chiliboard.dtb \
-	am335x-cm-t335.dtb \
-	am335x-evm.dtb \
-	am335x-evmsk.dtb \
-	am335x-guardian.dtb \
-	am335x-icev2.dtb \
-	am335x-lxm.dtb \
-	am335x-moxa-uc-2101.dtb \
-	am335x-moxa-uc-8100-me-t.dtb \
-	am335x-nano.dtb \
-	am335x-netcan-plus-1xx.dtb \
-	am335x-netcom-plus-2xx.dtb \
-	am335x-netcom-plus-8xx.dtb \
-	am335x-pdu001.dtb \
-	am335x-pepper.dtb \
-	am335x-phycore-rdk.dtb \
-	am335x-pocketbeagle.dtb \
-	am335x-regor-rdk.dtb \
-	am335x-sancloud-bbe.dtb \
-	am335x-shc.dtb \
-	am335x-sbc-t335.dtb \
-	am335x-sl50.dtb \
-	am335x-wega-rdk.dtb \
-	am335x-osd3358-sm-red.dtb
-dtb-$(CONFIG_ARCH_OMAP4) += \
-	omap4-droid-bionic-xt875.dtb \
-	omap4-droid4-xt894.dtb \
-	omap4-duovero-parlor.dtb \
-	omap4-kc1.dtb \
-	omap4-panda.dtb \
-	omap4-panda-a4.dtb \
-	omap4-panda-es.dtb \
-	omap4-sdp.dtb \
-	omap4-sdp-es23plus.dtb \
-	omap4-var-dvk-om44.dtb \
-	omap4-var-stk-om44.dtb
-dtb-$(CONFIG_SOC_AM43XX) += \
-	am43x-epos-evm.dtb \
-	am437x-cm-t43.dtb \
-	am437x-gp-evm.dtb \
-	am437x-idk-evm.dtb \
-	am437x-sbc-t43.dtb \
-	am437x-sk-evm.dtb
-dtb-$(CONFIG_SOC_OMAP5) += \
-	omap5-cm-t54.dtb \
-	omap5-igep0050.dtb \
-	omap5-sbc-t54.dtb \
-	omap5-uevm.dtb
-dtb-$(CONFIG_SOC_DRA7XX) += \
-	am57xx-beagle-x15.dtb \
-	am57xx-beagle-x15-revb1.dtb \
-	am57xx-beagle-x15-revc.dtb \
-	am57xx-cl-som-am57x.dtb \
-	am57xx-sbc-am57x.dtb \
-	am572x-idk.dtb \
-	am571x-idk.dtb \
-	am574x-idk.dtb \
-	dra7-evm.dtb \
-	dra72-evm.dtb \
-	dra72-evm-revc.dtb \
-	dra71-evm.dtb \
-	dra76-evm.dtb
-dtb-$(CONFIG_ARCH_ORION5X) += \
-	orion5x-kuroboxpro.dtb \
-	orion5x-lacie-d2-network.dtb \
-	orion5x-lacie-ethernet-disk-mini-v2.dtb \
-	orion5x-linkstation-lsgl.dtb \
-	orion5x-linkstation-lswtgl.dtb \
-	orion5x-linkstation-lschl.dtb \
-	orion5x-lswsgl.dtb \
-	orion5x-maxtor-shared-storage-2.dtb \
-	orion5x-netgear-wnr854t.dtb \
-	orion5x-rd88f5182-nas.dtb
-dtb-$(CONFIG_ARCH_ACTIONS) += \
-	owl-s500-cubieboard6.dtb \
-	owl-s500-guitar-bb-rev-b.dtb \
-	owl-s500-sparky.dtb
-dtb-$(CONFIG_ARCH_PRIMA2) += \
-	prima2-evb.dtb
-dtb-$(CONFIG_ARCH_PXA) += \
-	pxa300-raumfeld-connector.dtb \
-	pxa300-raumfeld-controller.dtb \
-	pxa300-raumfeld-speaker-l.dtb \
-	pxa300-raumfeld-speaker-m.dtb \
-	pxa300-raumfeld-speaker-one.dtb \
-	pxa300-raumfeld-speaker-s.dtb
-dtb-$(CONFIG_ARCH_OXNAS) += \
-	ox810se-wd-mbwe.dtb \
-	ox820-cloudengines-pogoplug-series-3.dtb
-dtb-$(CONFIG_ARCH_QCOM) += \
-	qcom-apq8060-dragonboard.dtb \
-	qcom-apq8064-cm-qs600.dtb \
-	qcom-apq8064-ifc6410.dtb \
-	qcom-apq8064-sony-xperia-yuga.dtb \
-	qcom-apq8064-asus-nexus7-flo.dtb \
-	qcom-apq8074-dragonboard.dtb \
-	qcom-apq8084-ifc6540.dtb \
-	qcom-apq8084-mtp.dtb \
-	qcom-ipq4019-ap.dk01.1-c1.dtb \
-	qcom-ipq4019-ap.dk04.1-c1.dtb \
-	qcom-ipq4019-ap.dk04.1-c3.dtb \
-	qcom-ipq4019-ap.dk07.1-c1.dtb \
-	qcom-ipq4019-ap.dk07.1-c2.dtb \
-	qcom-ipq8064-ap148.dtb \
-	qcom-msm8660-surf.dtb \
-	qcom-msm8960-cdp.dtb \
-	qcom-msm8974-fairphone-fp2.dtb \
-	qcom-msm8974-lge-nexus5-hammerhead.dtb \
-	qcom-msm8974-samsung-klte.dtb \
-	qcom-msm8974-sony-xperia-amami.dtb \
-	qcom-msm8974-sony-xperia-castor.dtb \
-	qcom-msm8974-sony-xperia-honami.dtb \
-	qcom-mdm9615-wp8548-mangoh-green.dtb
-dtb-$(CONFIG_ARCH_RDA) += \
-	rda8810pl-orangepi-2g-iot.dtb \
-	rda8810pl-orangepi-i96.dtb
-dtb-$(CONFIG_ARCH_REALVIEW) += \
-	arm-realview-pb1176.dtb \
-	arm-realview-pb11mp.dtb \
-	arm-realview-eb.dtb \
-	arm-realview-eb-bbrevd.dtb \
-	arm-realview-eb-11mp.dtb \
-	arm-realview-eb-11mp-bbrevd.dtb \
-	arm-realview-eb-11mp-ctrevb.dtb \
-	arm-realview-eb-11mp-bbrevd-ctrevb.dtb \
-	arm-realview-eb-a9mp.dtb \
-	arm-realview-eb-a9mp-bbrevd.dtb \
-	arm-realview-pba8.dtb \
-	arm-realview-pbx-a9.dtb
-dtb-$(CONFIG_ARCH_RENESAS) += \
-	emev2-kzm9d.dtb \
-	r7s72100-genmai.dtb \
-	r7s72100-gr-peach.dtb \
-	r7s72100-rskrza1.dtb \
-	r7s9210-rza2mevb.dtb \
-	r8a73a4-ape6evm.dtb \
-	r8a7740-armadillo800eva.dtb \
-	r8a7743-iwg20d-q7.dtb \
-	r8a7743-iwg20d-q7-dbcm-ca.dtb \
-	r8a7743-sk-rzg1m.dtb \
-	r8a7744-iwg20d-q7.dtb \
-	r8a7744-iwg20d-q7-dbcm-ca.dtb \
-	r8a7745-iwg22d-sodimm.dtb \
-	r8a7745-iwg22d-sodimm-dbhd-ca.dtb \
-	r8a7745-sk-rzg1e.dtb \
-	r8a77470-iwg23s-sbc.dtb \
-	r8a7778-bockw.dtb \
-	r8a7779-marzen.dtb \
-	r8a7790-lager.dtb \
-	r8a7790-stout.dtb \
-	r8a7791-koelsch.dtb \
-	r8a7791-porter.dtb \
-	r8a7792-blanche.dtb \
-	r8a7792-wheat.dtb \
-	r8a7793-gose.dtb \
-	r8a7794-alt.dtb \
-	r8a7794-silk.dtb \
-	r9a06g032-rzn1d400-db.dtb \
-	sh73a0-kzm9g.dtb
-dtb-$(CONFIG_ARCH_ROCKCHIP) += \
-	rv1108-elgin-r1.dtb \
-	rv1108-evb.dtb \
-	rk3036-evb.dtb \
-	rk3036-kylin.dtb \
-	rk3066a-bqcurie2.dtb \
-	rk3066a-marsboard.dtb \
-	rk3066a-mk808.dtb \
-	rk3066a-rayeager.dtb \
-	rk3188-bqedison2qc.dtb \
-	rk3188-px3-evb.dtb \
-	rk3188-radxarock.dtb \
-	rk3228-evb.dtb \
-	rk3229-evb.dtb \
-	rk3229-xms6.dtb \
-	rk3288-evb-act8846.dtb \
-	rk3288-evb-rk808.dtb \
-	rk3288-firefly-beta.dtb \
-	rk3288-firefly.dtb \
-	rk3288-firefly-reload.dtb \
-	rk3288-miqi.dtb \
-	rk3288-phycore-rdk.dtb \
-	rk3288-popmetal.dtb \
-	rk3288-r89.dtb \
-	rk3288-rock2-square.dtb \
-	rk3288-tinker.dtb \
-	rk3288-tinker-s.dtb \
-	rk3288-veyron-brain.dtb \
-	rk3288-veyron-fievel.dtb \
-	rk3288-veyron-jaq.dtb \
-	rk3288-veyron-jerry.dtb \
-	rk3288-veyron-mickey.dtb \
-	rk3288-veyron-mighty.dtb \
-	rk3288-veyron-minnie.dtb \
-	rk3288-veyron-pinky.dtb \
-	rk3288-veyron-speedy.dtb \
-	rk3288-veyron-tiger.dtb \
-	rk3288-vyasa.dtb
-dtb-$(CONFIG_ARCH_S3C24XX) += \
-	s3c2416-smdk2416.dtb
-dtb-$(CONFIG_ARCH_S3C64XX) += \
-	s3c6410-mini6410.dtb \
-	s3c6410-smdk6410.dtb
-dtb-$(CONFIG_ARCH_S5PV210) += \
-	s5pv210-aquila.dtb \
-	s5pv210-fascinate4g.dtb \
-	s5pv210-galaxys.dtb \
-	s5pv210-goni.dtb \
-	s5pv210-smdkc110.dtb \
-	s5pv210-smdkv210.dtb \
-	s5pv210-torbreck.dtb
-dtb-$(CONFIG_ARCH_SOCFPGA) += \
-	socfpga_arria5_socdk.dtb \
-	socfpga_arria10_socdk_nand.dtb \
-	socfpga_arria10_socdk_qspi.dtb \
-	socfpga_arria10_socdk_sdmmc.dtb \
-	socfpga_cyclone5_chameleon96.dtb \
-	socfpga_cyclone5_mcvevk.dtb \
-	socfpga_cyclone5_socdk.dtb \
-	socfpga_cyclone5_de0_nano_soc.dtb \
-	socfpga_cyclone5_sockit.dtb \
-	socfpga_cyclone5_socrates.dtb \
-	socfpga_cyclone5_sodia.dtb \
-	socfpga_cyclone5_vining_fpga.dtb \
-	socfpga_vt.dtb
-dtb-$(CONFIG_ARCH_SPEAR13XX) += \
-	spear1310-evb.dtb \
-	spear1340-evb.dtb
-dtb-$(CONFIG_ARCH_SPEAR3XX) += \
-	spear300-evb.dtb \
-	spear310-evb.dtb \
-	spear320-evb.dtb \
-	spear320-hmi.dtb
-dtb-$(CONFIG_ARCH_SPEAR6XX) += \
-	spear600-evb.dtb
-dtb-$(CONFIG_ARCH_STI) += \
-	stih407-b2120.dtb \
-	stih410-b2120.dtb \
-	stih410-b2260.dtb \
-	stih418-b2199.dtb
-dtb-$(CONFIG_ARCH_STM32) += \
-	stm32f429-disco.dtb \
-	stm32f469-disco.dtb \
-	stm32f746-disco.dtb \
-	stm32f769-disco.dtb \
-	stm32429i-eval.dtb \
-	stm32746g-eval.dtb \
-	stm32h743i-eval.dtb \
-	stm32h743i-disco.dtb \
-	stm32mp157a-avenger96.dtb \
-	stm32mp157a-dk1.dtb \
-	stm32mp157c-dk2.dtb \
-	stm32mp157c-ed1.dtb \
-	stm32mp157c-ev1.dtb
-dtb-$(CONFIG_MACH_SUN4I) += \
-	sun4i-a10-a1000.dtb \
-	sun4i-a10-ba10-tvbox.dtb \
-	sun4i-a10-chuwi-v7-cw0825.dtb \
-	sun4i-a10-cubieboard.dtb \
-	sun4i-a10-dserve-dsrv9703c.dtb \
-	sun4i-a10-gemei-g9.dtb \
-	sun4i-a10-hackberry.dtb \
-	sun4i-a10-hyundai-a7hd.dtb \
-	sun4i-a10-inet1.dtb \
-	sun4i-a10-inet97fv2.dtb \
-	sun4i-a10-inet9f-rev03.dtb \
-	sun4i-a10-itead-iteaduino-plus.dtb \
-	sun4i-a10-jesurun-q5.dtb \
-	sun4i-a10-marsboard.dtb \
-	sun4i-a10-mini-xplus.dtb \
-	sun4i-a10-mk802.dtb \
-	sun4i-a10-mk802ii.dtb \
-	sun4i-a10-olinuxino-lime.dtb \
-	sun4i-a10-pcduino.dtb \
-	sun4i-a10-pcduino2.dtb \
-	sun4i-a10-pov-protab2-ips9.dtb
-dtb-$(CONFIG_MACH_SUN5I) += \
-	sun5i-a10s-auxtek-t003.dtb \
-	sun5i-a10s-auxtek-t004.dtb \
-	sun5i-a10s-mk802.dtb \
-	sun5i-a10s-olinuxino-micro.dtb \
-	sun5i-a10s-r7-tv-dongle.dtb \
-	sun5i-a10s-wobo-i5.dtb \
-	sun5i-a13-difrnce-dit4350.dtb \
-	sun5i-a13-empire-electronix-d709.dtb \
-	sun5i-a13-empire-electronix-m712.dtb \
-	sun5i-a13-hsg-h702.dtb \
-	sun5i-a13-inet-98v-rev2.dtb \
-	sun5i-a13-licheepi-one.dtb \
-	sun5i-a13-olinuxino.dtb \
-	sun5i-a13-olinuxino-micro.dtb \
-	sun5i-a13-q8-tablet.dtb \
-	sun5i-a13-utoo-p66.dtb \
-	sun5i-gr8-chip-pro.dtb \
-	sun5i-gr8-evb.dtb \
-	sun5i-r8-chip.dtb
-dtb-$(CONFIG_MACH_SUN6I) += \
-	sun6i-a31-app4-evb1.dtb \
-	sun6i-a31-colombus.dtb \
-	sun6i-a31-hummingbird.dtb \
-	sun6i-a31-i7.dtb \
-	sun6i-a31-m9.dtb \
-	sun6i-a31-mele-a1000g-quad.dtb \
-	sun6i-a31s-colorfly-e708-q1.dtb \
-	sun6i-a31s-cs908.dtb \
-	sun6i-a31s-inet-q972.dtb \
-	sun6i-a31s-primo81.dtb \
-	sun6i-a31s-sina31s.dtb \
-	sun6i-a31s-sinovoip-bpi-m2.dtb \
-	sun6i-a31s-yones-toptech-bs1078-v2.dtb
-dtb-$(CONFIG_MACH_SUN7I) += \
-	sun7i-a20-bananapi.dtb \
-	sun7i-a20-bananapi-m1-plus.dtb \
-	sun7i-a20-bananapro.dtb \
-	sun7i-a20-cubieboard2.dtb \
-	sun7i-a20-cubietruck.dtb \
-	sun7i-a20-hummingbird.dtb \
-	sun7i-a20-itead-ibox.dtb \
-	sun7i-a20-i12-tvbox.dtb \
-	sun7i-a20-icnova-swac.dtb \
-	sun7i-a20-lamobo-r1.dtb \
-	sun7i-a20-m3.dtb \
-	sun7i-a20-mk808c.dtb \
-	sun7i-a20-olimex-som-evb.dtb \
-	sun7i-a20-olimex-som-evb-emmc.dtb \
-	sun7i-a20-olimex-som204-evb.dtb \
-	sun7i-a20-olimex-som204-evb-emmc.dtb \
-	sun7i-a20-olinuxino-lime.dtb \
-	sun7i-a20-olinuxino-lime2.dtb \
-	sun7i-a20-olinuxino-lime2-emmc.dtb \
-	sun7i-a20-olinuxino-micro.dtb \
-	sun7i-a20-olinuxino-micro-emmc.dtb \
-	sun7i-a20-orangepi.dtb \
-	sun7i-a20-orangepi-mini.dtb \
-	sun7i-a20-pcduino3.dtb \
-	sun7i-a20-pcduino3-nano.dtb \
-	sun7i-a20-wexler-tab7200.dtb \
-	sun7i-a20-wits-pro-a20-dkt.dtb
-dtb-$(CONFIG_MACH_SUN8I) += \
-	sun8i-a23-evb.dtb \
-	sun8i-a23-gt90h-v4.dtb \
-	sun8i-a23-inet86dz.dtb \
-	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb \
-	sun8i-a23-polaroid-mid2407pxe03.dtb \
-	sun8i-a23-polaroid-mid2809pxe04.dtb \
-	sun8i-a23-q8-tablet.dtb \
-	sun8i-a33-et-q8-v1.6.dtb \
-	sun8i-a33-ga10h-v1.1.dtb \
-	sun8i-a33-inet-d978-rev2.dtb \
-	sun8i-a33-ippo-q8h-v1.2.dtb \
-	sun8i-a33-olinuxino.dtb \
-	sun8i-a33-q8-tablet.dtb \
-	sun8i-a33-sinlinx-sina33.dtb \
-	sun8i-a83t-allwinner-h8homlet-v2.dtb \
-	sun8i-a83t-bananapi-m3.dtb \
-	sun8i-a83t-cubietruck-plus.dtb \
-	sun8i-a83t-tbs-a711.dtb \
-	sun8i-h2-plus-bananapi-m2-zero.dtb \
-	sun8i-h2-plus-libretech-all-h3-cc.dtb \
-	sun8i-h2-plus-orangepi-r1.dtb \
-	sun8i-h2-plus-orangepi-zero.dtb \
-	sun8i-h3-bananapi-m2-plus.dtb \
-	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
-	sun8i-h3-beelink-x2.dtb \
-	sun8i-h3-libretech-all-h3-cc.dtb \
-	sun8i-h3-mapleboard-mp130.dtb \
-	sun8i-h3-nanopi-duo2.dtb \
-	sun8i-h3-nanopi-m1.dtb	\
-	sun8i-h3-nanopi-m1-plus.dtb \
-	sun8i-h3-nanopi-neo.dtb \
-	sun8i-h3-nanopi-neo-air.dtb \
-	sun8i-h3-orangepi-2.dtb \
-	sun8i-h3-orangepi-lite.dtb \
-	sun8i-h3-orangepi-one.dtb \
-	sun8i-h3-orangepi-pc.dtb \
-	sun8i-h3-orangepi-pc-plus.dtb \
-	sun8i-h3-orangepi-plus.dtb \
-	sun8i-h3-orangepi-plus2e.dtb \
-	sun8i-h3-orangepi-zero-plus2.dtb \
-	sun8i-h3-rervision-dvk.dtb \
-	sun8i-r16-bananapi-m2m.dtb \
-	sun8i-r16-nintendo-nes-classic.dtb \
-	sun8i-r16-nintendo-super-nes-classic.dtb \
-	sun8i-r16-parrot.dtb \
-	sun8i-r40-bananapi-m2-ultra.dtb \
-	sun8i-s3-lichee-zero-plus.dtb \
-	sun8i-t3-cqa3t-bv3.dtb \
-	sun8i-v3s-licheepi-zero.dtb \
-	sun8i-v3s-licheepi-zero-dock.dtb \
-	sun8i-v40-bananapi-m2-berry.dtb
-dtb-$(CONFIG_MACH_SUN9I) += \
-	sun9i-a80-optimus.dtb \
-	sun9i-a80-cubieboard4.dtb
-dtb-$(CONFIG_MACH_SUNIV) += \
-	suniv-f1c100s-licheepi-nano.dtb
-dtb-$(CONFIG_ARCH_TANGO) += \
-	tango4-vantage-1172.dtb
-dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
-	tegra20-harmony.dtb \
-	tegra20-colibri-eval-v3.dtb \
-	tegra20-colibri-iris.dtb \
-	tegra20-medcom-wide.dtb \
-	tegra20-paz00.dtb \
-	tegra20-plutux.dtb \
-	tegra20-seaboard.dtb \
-	tegra20-tec.dtb \
-	tegra20-trimslice.dtb \
-	tegra20-ventana.dtb
-dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
-	tegra30-apalis-eval.dtb \
-	tegra30-apalis-v1.1-eval.dtb \
-	tegra30-beaver.dtb \
-	tegra30-cardhu-a02.dtb \
-	tegra30-cardhu-a04.dtb \
-	tegra30-colibri-eval-v3.dtb
-dtb-$(CONFIG_ARCH_TEGRA_114_SOC) += \
-	tegra114-dalmore.dtb \
-	tegra114-roth.dtb \
-	tegra114-tn7.dtb
-dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \
-	tegra124-apalis-eval.dtb \
-	tegra124-apalis-v1.2-eval.dtb \
-	tegra124-jetson-tk1.dtb \
-	tegra124-nyan-big.dtb \
-	tegra124-nyan-blaze.dtb \
-	tegra124-venice2.dtb
-dtb-$(CONFIG_ARCH_U300) += \
-	ste-u300.dtb
-dtb-$(CONFIG_ARCH_U8500) += \
-	ste-snowball.dtb \
-	ste-hrefprev60-stuib.dtb \
-	ste-hrefprev60-tvk.dtb \
-	ste-hrefv60plus-stuib.dtb \
-	ste-hrefv60plus-tvk.dtb
-dtb-$(CONFIG_ARCH_UNIPHIER) += \
-	uniphier-ld4-ref.dtb \
-	uniphier-ld6b-ref.dtb \
-	uniphier-pro4-ace.dtb \
-	uniphier-pro4-ref.dtb \
-	uniphier-pro4-sanji.dtb \
-	uniphier-pxs2-gentil.dtb \
-	uniphier-pxs2-vodka.dtb \
-	uniphier-sld8-ref.dtb
-dtb-$(CONFIG_ARCH_VERSATILE) += \
-	versatile-ab.dtb \
-	versatile-ab-ib2.dtb \
-	versatile-pb.dtb
-dtb-$(CONFIG_ARCH_VEXPRESS) += \
-	vexpress-v2p-ca5s.dtb \
-	vexpress-v2p-ca9.dtb \
-	vexpress-v2p-ca15-tc1.dtb \
-	vexpress-v2p-ca15_a7.dtb
-dtb-$(CONFIG_ARCH_VIRT) += \
-	xenvm-4.2.dtb
-dtb-$(CONFIG_ARCH_VT8500) += \
-	vt8500-bv07.dtb \
-	wm8505-ref.dtb \
-	wm8650-mid.dtb \
-	wm8750-apc8750.dtb \
-	wm8850-w70v2.dtb
-dtb-$(CONFIG_ARCH_ZYNQ) += \
-	zynq-cc108.dtb \
-	zynq-microzed.dtb \
-	zynq-parallella.dtb \
-	zynq-zc702.dtb \
-	zynq-zc706.dtb \
-	zynq-zc770-xm010.dtb \
-	zynq-zc770-xm011.dtb \
-	zynq-zc770-xm012.dtb \
-	zynq-zc770-xm013.dtb \
-	zynq-zed.dtb \
-	zynq-zturn.dtb \
-	zynq-zybo.dtb \
-	zynq-zybo-z7.dtb
-dtb-$(CONFIG_MACH_ARMADA_370) += \
-	armada-370-db.dtb \
-	armada-370-dlink-dns327l.dtb \
-	armada-370-mirabox.dtb \
-	armada-370-netgear-rn102.dtb \
-	armada-370-netgear-rn104.dtb \
-	armada-370-rd.dtb \
-	armada-370-seagate-nas-2bay.dtb \
-	armada-370-seagate-nas-4bay.dtb \
-	armada-370-seagate-personal-cloud.dtb \
-	armada-370-seagate-personal-cloud-2bay.dtb \
-	armada-370-synology-ds213j.dtb
-dtb-$(CONFIG_MACH_ARMADA_375) += \
-	armada-375-db.dtb
-dtb-$(CONFIG_MACH_ARMADA_38X) += \
-	armada-385-db-88f6820-amc.dtb \
-	armada-385-db-ap.dtb \
-	armada-385-linksys-caiman.dtb \
-	armada-385-linksys-cobra.dtb \
-	armada-385-linksys-rango.dtb \
-	armada-385-linksys-shelby.dtb \
-	armada-385-synology-ds116.dtb \
-	armada-385-turris-omnia.dtb \
-	armada-388-clearfog.dtb \
-	armada-388-clearfog-base.dtb \
-	armada-388-clearfog-pro.dtb \
-	armada-388-db.dtb \
-	armada-388-gp.dtb \
-	armada-388-helios4.dtb \
-	armada-388-rd.dtb
-dtb-$(CONFIG_MACH_ARMADA_39X) += \
-	armada-398-db.dtb
-dtb-$(CONFIG_MACH_ARMADA_XP) += \
-	armada-xp-axpwifiap.dtb \
-	armada-xp-db.dtb \
-	armada-xp-db-dxbc2.dtb \
-	armada-xp-db-xc3-24g4xg.dtb \
-	armada-xp-gp.dtb \
-	armada-xp-lenovo-ix4-300d.dtb \
-	armada-xp-linksys-mamba.dtb \
-	armada-xp-matrix.dtb \
-	armada-xp-netgear-rn2120.dtb \
-	armada-xp-openblocks-ax3-4.dtb \
-	armada-xp-synology-ds414.dtb
-dtb-$(CONFIG_MACH_DOVE) += \
-	dove-cubox.dtb \
-	dove-cubox-es.dtb \
-	dove-d2plug.dtb \
-	dove-d3plug.dtb \
-	dove-dove-db.dtb \
-	dove-sbc-a510.dtb
-dtb-$(CONFIG_ARCH_MEDIATEK) += \
-	mt2701-evb.dtb \
-	mt6580-evbp1.dtb \
-	mt6589-aquaris5.dtb \
-	mt6592-evb.dtb \
-	mt7623a-rfb-emmc.dtb \
-	mt7623a-rfb-nand.dtb \
-	mt7623n-rfb-emmc.dtb \
-	mt7623n-bananapi-bpi-r2.dtb \
-	mt7629-rfb.dtb \
-	mt8127-moose.dtb \
-	mt8135-evbp1.dtb
-dtb-$(CONFIG_ARCH_MILBEAUT) += milbeaut-m10v-evb.dtb
-dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
-dtb-$(CONFIG_ARCH_ASPEED) += \
-	aspeed-ast2500-evb.dtb \
-	aspeed-ast2600-evb.dtb \
-	aspeed-bmc-arm-centriq2400-rep.dtb \
-	aspeed-bmc-arm-stardragon4800-rep2.dtb \
-	aspeed-bmc-facebook-cmm.dtb \
-	aspeed-bmc-facebook-minipack.dtb \
-	aspeed-bmc-facebook-tiogapass.dtb \
-	aspeed-bmc-facebook-wedge40.dtb \
-	aspeed-bmc-facebook-wedge100.dtb \
-	aspeed-bmc-facebook-yamp.dtb \
-	aspeed-bmc-ibm-rainier.dtb \
-	aspeed-bmc-intel-s2600wf.dtb \
-	aspeed-bmc-inspur-fp5280g2.dtb \
-	aspeed-bmc-lenovo-hr630.dtb \
-	aspeed-bmc-lenovo-hr855xg2.dtb \
-	aspeed-bmc-microsoft-olympus.dtb \
-	aspeed-bmc-opp-lanyang.dtb \
-	aspeed-bmc-opp-mihawk.dtb \
-	aspeed-bmc-opp-palmetto.dtb \
-	aspeed-bmc-opp-romulus.dtb \
-	aspeed-bmc-opp-swift.dtb \
-	aspeed-bmc-opp-tacoma.dtb \
-	aspeed-bmc-opp-vesnin.dtb \
-	aspeed-bmc-opp-witherspoon.dtb \
-	aspeed-bmc-opp-zaius.dtb \
-	aspeed-bmc-portwell-neptune.dtb \
-	aspeed-bmc-quanta-q71l.dtb
+subdir-y += actions
+subdir-y += airoha
+subdir-y += allwinner
+subdir-y += alphascale
+subdir-y += amazon
+subdir-y += amlogic
+subdir-y += arm
+subdir-y += aspeed
+subdir-y += axis
+subdir-y += broadcom
+subdir-y += calxeda
+subdir-y += cirrus
+subdir-y += cnxt
+subdir-y += gemini
+subdir-y += hisilicon
+subdir-y += hpe
+subdir-y += intel
+subdir-y += marvell
+subdir-y += mediatek
+subdir-y += microchip
+subdir-y += moxa
+subdir-y += nspire
+subdir-y += nuvoton
+subdir-y += nvidia
+subdir-y += nxp
+subdir-y += qcom
+subdir-y += realtek
+subdir-y += renesas
+subdir-y += rockchip
+subdir-y += samsung
+subdir-y += sigmastar
+subdir-y += socionext
+subdir-y += st
+subdir-y += sunplus
+subdir-y += synaptics
+subdir-y += ti
+subdir-y += unisoc
+subdir-y += vt8500
+subdir-y += xen
+subdir-y += xilinx
diff --git a/arch/arm/boot/dts/actions/Makefile b/arch/arm/boot/dts/actions/Makefile
new file mode 100644
index 000000000000..f384e4a48e6f
--- /dev/null
+++ b/arch/arm/boot/dts/actions/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ACTIONS) += \
+	owl-s500-cubieboard6.dtb \
+	owl-s500-guitar-bb-rev-b.dtb \
+	owl-s500-labrador-base-m.dtb \
+	owl-s500-roseapplepi.dtb \
+	owl-s500-sparky.dtb
diff --git a/arch/arm/boot/dts/owl-s500-cubieboard6.dts b/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts
index 7c96c59b610d..c2b02895910c 100644
--- a/arch/arm/boot/dts/owl-s500-cubieboard6.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts
@@ -25,12 +25,6 @@
 		device_type = "memory";
 		reg = <0x0 0x80000000>;
 	};
-
-	uart3_clk: uart3-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <921600>;
-		#clock-cells = <0>;
-	};
 };
 
 &timer {
@@ -39,5 +33,4 @@
 
 &uart3 {
 	status = "okay";
-	clocks = <&uart3_clk>;
 };
diff --git a/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts b/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts
index e610d49395d2..7ae34a23e320 100644
--- a/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts
@@ -18,15 +18,8 @@
 	chosen {
 		stdout-path = "serial3:115200n8";
 	};
-
-	uart3_clk: uart3-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <921600>;
-		#clock-cells = <0>;
-	};
 };
 
 &uart3 {
 	status = "okay";
-	clocks = <&uart3_clk>;
 };
diff --git a/arch/arm/boot/dts/owl-s500-guitar.dtsi b/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi
index 81cc39871f17..81cc39871f17 100644
--- a/arch/arm/boot/dts/owl-s500-guitar.dtsi
+++ b/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi
diff --git a/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts b/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts
new file mode 100644
index 000000000000..1585e33f703b
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Caninos Labrador Base Board
+ *
+ * Copyright (c) 2019-2020 Matheus Castello
+ */
+
+/dts-v1/;
+
+#include "owl-s500-labrador-v2.dtsi"
+
+/ {
+	model = "Caninos Labrador Core v2 on Labrador Base-M v1";
+	compatible = "caninos,labrador-base-m",
+		     "caninos,labrador-v2", "actions,s500";
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi b/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi
new file mode 100644
index 000000000000..883ff2f9886d
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Caninos Labrador SoM V2
+ *
+ * Copyright (c) 2019-2020 Matheus Castello
+ */
+
+#include "owl-s500.dtsi"
+
+/ {
+	model = "Caninos Labrador Core V2.1";
+	compatible = "caninos,labrador-v2", "actions,s500";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x80000000>;
+	};
+};
+
+&timer {
+	clocks = <&hosc>;
+};
diff --git a/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts
new file mode 100644
index 000000000000..eb555f385283
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts
@@ -0,0 +1,299 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Roseapple Pi
+ *
+ * Copyright (C) 2020-2021 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "owl-s500.dtsi"
+
+/ {
+	compatible = "roseapplepi,roseapplepi", "actions,s500";
+	model = "Roseapple Pi";
+
+	aliases {
+		mmc0 = &mmc0;
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	syspwr: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SYSPWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	atc260x: pmic@65 {
+		compatible = "actions,atc2603c";
+		reg = <0x65>;
+		interrupt-parent = <&sirq>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+
+		reset-time-sec = <6>;
+
+		regulators {
+			compatible = "actions,atc2603c-regulator";
+
+			dcdc1-supply = <&syspwr>;
+			dcdc2-supply = <&syspwr>;
+			dcdc3-supply = <&syspwr>;
+			ldo1-supply = <&syspwr>;
+			ldo2-supply = <&syspwr>;
+			ldo3-supply = <&syspwr>;
+			ldo5-supply = <&syspwr>;
+			ldo6-supply = <&syspwr>;
+			ldo7-supply = <&syspwr>;
+			ldo8-supply = <&syspwr>;
+			ldo11-supply = <&syspwr>;
+			ldo12-supply = <&syspwr>;
+			switchldo1-supply = <&vcc>;
+
+			vdd_cpu: dcdc1 {
+				regulator-name = "VDD_CPU";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+			};
+
+			vddq: dcdc2 {
+				regulator-name = "VDDQ";
+				regulator-min-microvolt = <1300000>;
+				regulator-max-microvolt = <2150000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc: dcdc3 {
+				regulator-name = "VCC";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vcc_3v3: ldo1 {
+				regulator-name = "VCC_3V3";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			avcc: ldo2 {
+				regulator-name = "AVCC";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_1v8: ldo3 {
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vcc_3v1: ldo5 {
+				regulator-name = "VCC_3V1";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			avdd: ldo6 {
+				regulator-name = "AVDD";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+			};
+
+			sens_1v8: ldo7 {
+				regulator-name = "SENS_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo8: ldo8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <2300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			svcc: ldo11 {
+				regulator-name = "SVCC";
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			rtc_vdd: ldo12 {
+				regulator-name = "RTC_VDD";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			sd_vcc: switchldo1 {
+				regulator-name = "SD_VCC";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+};
+
+&i2c2 {
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+};
+
+&pinctrl {
+	i2c0_pins: i2c0-pins {
+		pinmux {
+			groups = "i2c0_mfp";
+			function = "i2c0";
+		};
+
+		pinconf {
+			pins = "i2c0_sclk", "i2c0_sdata";
+			bias-pull-up;
+		};
+	};
+
+	i2c1_pins: i2c1-pins {
+		pinconf {
+			pins = "i2c1_sclk", "i2c1_sdata";
+			bias-pull-up;
+		};
+	};
+
+	i2c2_pins: i2c2-pins {
+		pinconf {
+			pins = "i2c2_sclk", "i2c2_sdata";
+			bias-pull-up;
+		};
+	};
+
+	mmc0_pins: mmc0-pins {
+		pinmux {
+			groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
+				 "sd0_cmd_mfp", "sd0_clk_mfp";
+			function = "sd0";
+		};
+
+		drv-pinconf {
+			groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv";
+			drive-strength = <8>;
+		};
+
+		bias0-pinconf {
+			pins = "sd0_d0", "sd0_d1", "sd0_d2",
+			       "sd0_d3", "sd0_cmd";
+			bias-pull-up;
+		};
+
+		bias1-pinconf {
+			pins = "sd0_clk";
+			bias-pull-down;
+		};
+	};
+
+	ethernet_pins: ethernet-pins {
+		eth_rmii-pinmux {
+			groups = "rmii_txd0_mfp", "rmii_txd1_mfp",
+				 "rmii_rxd0_mfp", "rmii_rxd1_mfp",
+				 "rmii_txen_mfp", "rmii_rxen_mfp",
+				 "rmii_crs_dv_mfp", "rmii_ref_clk_mfp";
+			function = "eth_rmii";
+		};
+
+		phy_clk-pinmux {
+			groups = "clko_25m_mfp";
+			function = "clko_25m";
+		};
+
+		ref_clk-pinconf {
+			groups = "rmii_ref_clk_drv";
+			drive-strength = <2>;
+		};
+
+	};
+};
+
+/* uSD */
+&mmc0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	no-sdio;
+	no-mmc;
+	no-1-8-v;
+	cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&sd_vcc>;
+	vqmmc-supply = <&sd_vcc>;
+};
+
+&ethernet {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&eth_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <150000>;
+
+		eth_phy: ethernet-phy@3 {
+			reg = <0x3>;
+			max-speed = <100>;
+			interrupt-parent = <&sirq>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&twd_timer {
+	status = "okay";
+};
+
+&timer {
+	clocks = <&hosc>;
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/owl-s500-sparky.dts b/arch/arm/boot/dts/actions/owl-s500-sparky.dts
index c665ce8b88b4..9d8f7336bec0 100644
--- a/arch/arm/boot/dts/owl-s500-sparky.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-sparky.dts
@@ -25,12 +25,6 @@
 		device_type = "memory";
 		reg = <0x0 0x40000000>; /* 1 or 2 GiB */
 	};
-
-	uart3_clk: uart3-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <921600>;
-		#clock-cells = <0>;
-	};
 };
 
 &timer {
@@ -39,5 +33,4 @@
 
 &uart3 {
 	status = "okay";
-	clocks = <&uart3_clk>;
 };
diff --git a/arch/arm/boot/dts/actions/owl-s500.dtsi b/arch/arm/boot/dts/actions/owl-s500.dtsi
new file mode 100644
index 000000000000..739b4b9cec8c
--- /dev/null
+++ b/arch/arm/boot/dts/actions/owl-s500.dtsi
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Actions Semi S500 SoC
+ *
+ * Copyright (c) 2016-2017 Andreas Färber
+ */
+
+#include <dt-bindings/clock/actions,s500-cmu.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/owl-s500-powergate.h>
+#include <dt-bindings/reset/actions,s500-reset.h>
+
+/ {
+	compatible = "actions,s500";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+	};
+
+	chosen {
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x0>;
+			enable-method = "actions,s500-smp";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x1>;
+			enable-method = "actions,s500-smp";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x2>;
+			enable-method = "actions,s500-smp";
+			power-domains = <&sps S500_PD_CPU2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x3>;
+			enable-method = "actions,s500-smp";
+			power-domains = <&sps S500_PD_CPU3>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	hosc: hosc {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+	losc: losc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		scu: scu@b0020000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0xb0020000 0x100>;
+		};
+
+		global_timer: timer@b0020200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0xb0020200 0x100>;
+			interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+			status = "disabled";
+		};
+
+		twd_timer: timer@b0020600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0xb0020600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+			status = "disabled";
+		};
+
+		twd_wdt: wdt@b0020620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0xb0020620 0xe0>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@b0021000 {
+			compatible = "arm,cortex-a9-gic";
+			reg = <0xb0021000 0x1000>,
+			      <0xb0020100 0x0100>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		l2: cache-controller@b0022000 {
+			compatible = "arm,pl310-cache";
+			reg = <0xb0022000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			arm,tag-latency = <3 3 2>;
+			arm,data-latency = <5 3 3>;
+		};
+
+		uart0: serial@b0120000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0120000 0x2000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@b0122000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0122000 0x2000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@b0124000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0124000 0x2000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@b0126000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0126000 0x2000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@b0128000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb0128000 0x2000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@b012a000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb012a000 0x2000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART5>;
+			status = "disabled";
+		};
+
+		uart6: serial@b012c000 {
+			compatible = "actions,s500-uart", "actions,owl-uart";
+			reg = <0xb012c000 0x2000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART6>;
+			status = "disabled";
+		};
+
+		cmu: clock-controller@b0160000 {
+			compatible = "actions,s500-cmu";
+			reg = <0xb0160000 0x8000>;
+			clocks = <&hosc>, <&losc>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		i2c0: i2c@b0170000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb0170000 0x4000>;
+			clocks = <&cmu CLK_I2C0>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@b0174000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb0174000 0x4000>;
+			clocks = <&cmu CLK_I2C1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@b0178000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb0178000 0x4000>;
+			clocks = <&cmu CLK_I2C2>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@b017c000 {
+			compatible = "actions,s500-i2c";
+			reg = <0xb017c000 0x4000>;
+			clocks = <&cmu CLK_I2C3>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		sirq: interrupt-controller@b01b0200 {
+			compatible = "actions,s500-sirq";
+			reg = <0xb01b0200 0x4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ0 */
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ1 */
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; /* SIRQ2 */
+		};
+
+		timer: timer@b0168000 {
+			compatible = "actions,s500-timer";
+			reg = <0xb0168000 0x8000>;
+			interrupts = <GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "2hz0", "2hz1", "timer0", "timer1";
+		};
+
+		sps: power-controller@b01b0100 {
+			compatible = "actions,s500-sps";
+			reg = <0xb01b0100 0x100>;
+			#power-domain-cells = <1>;
+		};
+
+		pinctrl: pinctrl@b01b0000 {
+			compatible = "actions,s500-pinctrl";
+			reg = <0xb01b0000 0x40>, /* GPIO */
+			      <0xb01b0040 0x10>, /* Multiplexing Control */
+			      <0xb01b0060 0x18>, /* PAD Control */
+			      <0xb01b0080 0xc>;  /* PAD Drive Capacity */
+			clocks = <&cmu CLK_GPIO>;
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 132>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, /* GPIOA */
+				     <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, /* GPIOB */
+				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, /* GPIOC */
+				     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, /* GPIOD */
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; /* GPIOE */
+		};
+
+		dma: dma-controller@b0260000 {
+			compatible = "actions,s500-dma";
+			reg = <0xb0260000 0xd00>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			dma-channels = <12>;
+			dma-requests = <46>;
+			clocks = <&cmu CLK_DMAC>;
+			power-domains = <&sps S500_PD_DMA>;
+		};
+
+		mmc0: mmc@b0230000 {
+			compatible = "actions,s500-mmc", "actions,owl-mmc";
+			reg = <0xb0230000 0x38>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_SD0>;
+			resets = <&cmu RESET_SD0>;
+			dmas = <&dma 2>;
+			dma-names = "mmc";
+			status = "disabled";
+		};
+
+		mmc1: mmc@b0234000 {
+			compatible = "actions,s500-mmc", "actions,owl-mmc";
+			reg = <0xb0234000 0x38>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_SD1>;
+			resets = <&cmu RESET_SD1>;
+			dmas = <&dma 3>;
+			dma-names = "mmc";
+			status = "disabled";
+		};
+
+		mmc2: mmc@b0238000 {
+			compatible = "actions,s500-mmc", "actions,owl-mmc";
+			reg = <0xb0238000 0x38>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_SD2>;
+			resets = <&cmu RESET_SD2>;
+			dmas = <&dma 4>;
+			dma-names = "mmc";
+			status = "disabled";
+		};
+
+		ethernet: ethernet@b0310000 {
+			compatible = "actions,s500-emac", "actions,owl-emac";
+			reg = <0xb0310000 0x10000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_ETHERNET>, <&cmu CLK_RMII_REF>;
+			clock-names = "eth", "rmii";
+			resets = <&cmu RESET_ETHERNET>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/airoha/Makefile b/arch/arm/boot/dts/airoha/Makefile
new file mode 100644
index 000000000000..00c31389f622
--- /dev/null
+++ b/arch/arm/boot/dts/airoha/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_AIROHA) += \
+	en7523-evb.dtb
diff --git a/arch/arm/boot/dts/airoha/en7523-evb.dts b/arch/arm/boot/dts/airoha/en7523-evb.dts
new file mode 100644
index 000000000000..f23a25cce119
--- /dev/null
+++ b/arch/arm/boot/dts/airoha/en7523-evb.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+/* Bootloader installs ATF here */
+/memreserve/ 0x80000000 0x200000;
+
+#include "en7523.dtsi"
+
+/ {
+	model = "Airoha EN7523 Evaluation Board";
+	compatible = "airoha,en7523-evb", "airoha,en7523";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+		stdout-path = "serial0:115200n8";
+		linux,usable-memory-range = <0x80200000 0x1fe00000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/airoha/en7523.dtsi b/arch/arm/boot/dts/airoha/en7523.dtsi
new file mode 100644
index 000000000000..b523a868c4ad
--- /dev/null
+++ b/arch/arm/boot/dts/airoha/en7523.dtsi
@@ -0,0 +1,206 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/en7523-clk.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		npu_binary@84000000 {
+			no-map;
+			reg = <0x84000000 0xA00000>;
+		};
+
+		npu_flag@84B0000 {
+			no-map;
+			reg = <0x84B00000 0x100000>;
+		};
+
+		npu_pkt@85000000 {
+			no-map;
+			reg = <0x85000000 0x1A00000>;
+		};
+
+		npu_phyaddr@86B00000 {
+			no-map;
+			reg = <0x86B00000 0x100000>;
+		};
+
+		npu_rxdesc@86D00000 {
+			no-map;
+			reg = <0x86D00000 0x100000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	scu: system-controller@1fa20000 {
+		compatible = "airoha,en7523-scu";
+		reg = <0x1fa20000 0x400>,
+		      <0x1fb00000 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	gic: interrupt-controller@9000000 {
+		compatible = "arm,gic-v3";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x09000000 0x20000>,
+		      <0x09080000 0x80000>,
+		      <0x09400000 0x2000>,
+		      <0x09500000 0x2000>,
+		      <0x09600000 0x20000>;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	uart1: serial@1fbf0000 {
+		compatible = "ns16550";
+		reg = <0x1fbf0000 0x30>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <1843200>;
+		status = "okay";
+	};
+
+	gpio0: gpio@1fbf0200 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0204 0x4>,
+		      <0x1fbf0200 0x4>,
+		      <0x1fbf0220 0x4>,
+		      <0x1fbf0214 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio1: gpio@1fbf0270 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0270 0x4>,
+		      <0x1fbf0260 0x4>,
+		      <0x1fbf0264 0x4>,
+		      <0x1fbf0278 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pcie0: pcie@1fa91000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa91000 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000  0x20000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pcie1: pcie@1fa92000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa92000 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck1";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000  0x28000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
new file mode 100644
index 000000000000..2d26c3397f14
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -0,0 +1,335 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_SUN4I) += \
+	sun4i-a10-a1000.dtb \
+	sun4i-a10-ba10-tvbox.dtb \
+	sun4i-a10-chuwi-v7-cw0825.dtb \
+	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-dserve-dsrv9703c.dtb \
+	sun4i-a10-gemei-g9.dtb \
+	sun4i-a10-hackberry.dtb \
+	sun4i-a10-hyundai-a7hd.dtb \
+	sun4i-a10-inet1.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-inet9f-rev03.dtb \
+	sun4i-a10-itead-iteaduino-plus.dtb \
+	sun4i-a10-jesurun-q5.dtb \
+	sun4i-a10-marsboard.dtb \
+	sun4i-a10-mini-xplus.dtb \
+	sun4i-a10-mk802.dtb \
+	sun4i-a10-mk802ii.dtb \
+	sun4i-a10-olinuxino-lime.dtb \
+	sun4i-a10-pcduino.dtb \
+	sun4i-a10-pcduino2.dtb \
+	sun4i-a10-pov-protab2-ips9.dtb \
+	sun4i-a10-topwise-a721.dtb
+dtb-$(CONFIG_MACH_SUN4I) += \
+	sun4i-a10-a1000.dtb \
+	sun4i-a10-ba10-tvbox.dtb \
+	sun4i-a10-chuwi-v7-cw0825.dtb \
+	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-dserve-dsrv9703c.dtb \
+	sun4i-a10-gemei-g9.dtb \
+	sun4i-a10-hackberry.dtb \
+	sun4i-a10-hyundai-a7hd.dtb \
+	sun4i-a10-inet1.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-inet9f-rev03.dtb \
+	sun4i-a10-itead-iteaduino-plus.dtb \
+	sun4i-a10-jesurun-q5.dtb \
+	sun4i-a10-marsboard.dtb \
+	sun4i-a10-mini-xplus.dtb \
+	sun4i-a10-mk802.dtb \
+	sun4i-a10-mk802ii.dtb \
+	sun4i-a10-olinuxino-lime.dtb \
+	sun4i-a10-pcduino.dtb \
+	sun4i-a10-pcduino2.dtb \
+	sun4i-a10-pov-protab2-ips9.dtb \
+	sun4i-a10-topwise-a721.dtb
+dtb-$(CONFIG_MACH_SUN5I) += \
+	sun5i-a10s-auxtek-t003.dtb \
+	sun5i-a10s-auxtek-t004.dtb \
+	sun5i-a10s-mk802.dtb \
+	sun5i-a10s-olinuxino-micro.dtb \
+	sun5i-a10s-r7-tv-dongle.dtb \
+	sun5i-a10s-wobo-i5.dtb \
+	sun5i-a13-difrnce-dit4350.dtb \
+	sun5i-a13-empire-electronix-d709.dtb \
+	sun5i-a13-empire-electronix-m712.dtb \
+	sun5i-a13-hsg-h702.dtb \
+	sun5i-a13-inet-98v-rev2.dtb \
+	sun5i-a13-licheepi-one.dtb \
+	sun5i-a13-olinuxino.dtb \
+	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-pocketbook-touch-lux-3.dtb \
+	sun5i-a13-q8-tablet.dtb \
+	sun5i-a13-utoo-p66.dtb \
+	sun5i-gr8-chip-pro.dtb \
+	sun5i-gr8-evb.dtb \
+	sun5i-r8-chip.dtb
+dtb-$(CONFIG_MACH_SUN5I) += \
+	sun5i-a10s-auxtek-t003.dtb \
+	sun5i-a10s-auxtek-t004.dtb \
+	sun5i-a10s-mk802.dtb \
+	sun5i-a10s-olinuxino-micro.dtb \
+	sun5i-a10s-r7-tv-dongle.dtb \
+	sun5i-a10s-wobo-i5.dtb \
+	sun5i-a13-difrnce-dit4350.dtb \
+	sun5i-a13-empire-electronix-d709.dtb \
+	sun5i-a13-empire-electronix-m712.dtb \
+	sun5i-a13-hsg-h702.dtb \
+	sun5i-a13-inet-98v-rev2.dtb \
+	sun5i-a13-licheepi-one.dtb \
+	sun5i-a13-olinuxino.dtb \
+	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-pocketbook-touch-lux-3.dtb \
+	sun5i-a13-q8-tablet.dtb \
+	sun5i-a13-utoo-p66.dtb \
+	sun5i-gr8-chip-pro.dtb \
+	sun5i-gr8-evb.dtb \
+	sun5i-r8-chip.dtb
+dtb-$(CONFIG_MACH_SUN6I) += \
+	sun6i-a31-app4-evb1.dtb \
+	sun6i-a31-colombus.dtb \
+	sun6i-a31-hummingbird.dtb \
+	sun6i-a31-i7.dtb \
+	sun6i-a31-m9.dtb \
+	sun6i-a31-mele-a1000g-quad.dtb \
+	sun6i-a31s-colorfly-e708-q1.dtb \
+	sun6i-a31s-cs908.dtb \
+	sun6i-a31s-inet-q972.dtb \
+	sun6i-a31s-primo81.dtb \
+	sun6i-a31s-sina31s.dtb \
+	sun6i-a31s-sinovoip-bpi-m2.dtb \
+	sun6i-a31s-yones-toptech-bs1078-v2.dtb
+dtb-$(CONFIG_MACH_SUN6I) += \
+	sun6i-a31-app4-evb1.dtb \
+	sun6i-a31-colombus.dtb \
+	sun6i-a31-hummingbird.dtb \
+	sun6i-a31-i7.dtb \
+	sun6i-a31-m9.dtb \
+	sun6i-a31-mele-a1000g-quad.dtb \
+	sun6i-a31s-colorfly-e708-q1.dtb \
+	sun6i-a31s-cs908.dtb \
+	sun6i-a31s-inet-q972.dtb \
+	sun6i-a31s-primo81.dtb \
+	sun6i-a31s-sina31s.dtb \
+	sun6i-a31s-sinovoip-bpi-m2.dtb \
+	sun6i-a31s-yones-toptech-bs1078-v2.dtb
+dtb-$(CONFIG_MACH_SUN7I) += \
+	sun7i-a20-bananapi.dtb \
+	sun7i-a20-bananapi-m1-plus.dtb \
+	sun7i-a20-bananapro.dtb \
+	sun7i-a20-cubieboard2.dtb \
+	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
+	sun7i-a20-hummingbird.dtb \
+	sun7i-a20-itead-ibox.dtb \
+	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-icnova-a20-adb4006.dtb \
+	sun7i-a20-icnova-swac.dtb \
+	sun7i-a20-lamobo-r1.dtb \
+	sun7i-a20-linutronix-testbox-v2.dtb \
+	sun7i-a20-m3.dtb \
+	sun7i-a20-mk808c.dtb \
+	sun7i-a20-olimex-som-evb.dtb \
+	sun7i-a20-olimex-som-evb-emmc.dtb \
+	sun7i-a20-olimex-som204-evb.dtb \
+	sun7i-a20-olimex-som204-evb-emmc.dtb \
+	sun7i-a20-olinuxino-lime.dtb \
+	sun7i-a20-olinuxino-lime-emmc.dtb \
+	sun7i-a20-olinuxino-lime2.dtb \
+	sun7i-a20-olinuxino-lime2-emmc.dtb \
+	sun7i-a20-olinuxino-micro.dtb \
+	sun7i-a20-olinuxino-micro-emmc.dtb \
+	sun7i-a20-orangepi.dtb \
+	sun7i-a20-orangepi-mini.dtb \
+	sun7i-a20-pcduino3.dtb \
+	sun7i-a20-pcduino3-nano.dtb \
+	sun7i-a20-wexler-tab7200.dtb \
+	sun7i-a20-wits-pro-a20-dkt.dtb
+dtb-$(CONFIG_MACH_SUN7I) += \
+	sun7i-a20-bananapi.dtb \
+	sun7i-a20-bananapi-m1-plus.dtb \
+	sun7i-a20-bananapro.dtb \
+	sun7i-a20-cubieboard2.dtb \
+	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
+	sun7i-a20-hummingbird.dtb \
+	sun7i-a20-itead-ibox.dtb \
+	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-icnova-a20-adb4006.dtb \
+	sun7i-a20-icnova-swac.dtb \
+	sun7i-a20-lamobo-r1.dtb \
+	sun7i-a20-linutronix-testbox-v2.dtb \
+	sun7i-a20-m3.dtb \
+	sun7i-a20-mk808c.dtb \
+	sun7i-a20-olimex-som-evb.dtb \
+	sun7i-a20-olimex-som-evb-emmc.dtb \
+	sun7i-a20-olimex-som204-evb.dtb \
+	sun7i-a20-olimex-som204-evb-emmc.dtb \
+	sun7i-a20-olinuxino-lime.dtb \
+	sun7i-a20-olinuxino-lime-emmc.dtb \
+	sun7i-a20-olinuxino-lime2.dtb \
+	sun7i-a20-olinuxino-lime2-emmc.dtb \
+	sun7i-a20-olinuxino-micro.dtb \
+	sun7i-a20-olinuxino-micro-emmc.dtb \
+	sun7i-a20-orangepi.dtb \
+	sun7i-a20-orangepi-mini.dtb \
+	sun7i-a20-pcduino3.dtb \
+	sun7i-a20-pcduino3-nano.dtb \
+	sun7i-a20-wexler-tab7200.dtb \
+	sun7i-a20-wits-pro-a20-dkt.dtb
+
+# Enables support for device-tree overlays for all pis
+DTC_FLAGS_sun8i-h3-orangepi-lite := -@
+DTC_FLAGS_sun8i-h3-bananapi-m2-plus := -@
+DTC_FLAGS_sun8i-h3-nanopi-m1-plus := -@
+DTC_FLAGS_sun8i-h3-nanopi-m1 := -@
+DTC_FLAGS_sun8i-h3-nanopi-duo2 := -@
+DTC_FLAGS_sun8i-h3-orangepi-plus2e := -@
+DTC_FLAGS_sun8i-h3-orangepi-one := -@
+DTC_FLAGS_sun8i-h3-orangepi-plus := -@
+DTC_FLAGS_sun8i-h3-orangepi-2 := -@
+DTC_FLAGS_sun8i-h3-orangepi-zero-plus2 := -@
+DTC_FLAGS_sun8i-h3-nanopi-neo-air := -@
+DTC_FLAGS_sun8i-h3-zeropi := -@
+DTC_FLAGS_sun8i-h3-nanopi-neo := -@
+DTC_FLAGS_sun8i-h3-nanopi-r1 := -@
+DTC_FLAGS_sun8i-h3-orangepi-pc := -@
+DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@
+DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@
+dtb-$(CONFIG_MACH_SUN8I) += \
+	sun8i-a23-evb.dtb \
+	sun8i-a23-gt90h-v4.dtb \
+	sun8i-a23-inet86dz.dtb \
+	sun8i-a23-ippo-q8h-v5.dtb \
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-a23-polaroid-mid2407pxe03.dtb \
+	sun8i-a23-polaroid-mid2809pxe04.dtb \
+	sun8i-a23-q8-tablet.dtb \
+	sun8i-a33-et-q8-v1.6.dtb \
+	sun8i-a33-ga10h-v1.1.dtb \
+	sun8i-a33-inet-d978-rev2.dtb \
+	sun8i-a33-ippo-q8h-v1.2.dtb \
+	sun8i-a33-olinuxino.dtb \
+	sun8i-a33-q8-tablet.dtb \
+	sun8i-a33-sinlinx-sina33.dtb \
+	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-bananapi-m3.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
+	sun8i-a83t-tbs-a711.dtb \
+	sun8i-h2-plus-bananapi-m2-zero.dtb \
+	sun8i-h2-plus-libretech-all-h3-cc.dtb \
+	sun8i-h2-plus-orangepi-r1.dtb \
+	sun8i-h2-plus-orangepi-zero.dtb \
+	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
+	sun8i-h3-beelink-x2.dtb \
+	sun8i-h3-libretech-all-h3-cc.dtb \
+	sun8i-h3-mapleboard-mp130.dtb \
+	sun8i-h3-nanopi-duo2.dtb \
+	sun8i-h3-nanopi-m1.dtb \
+	sun8i-h3-nanopi-m1-plus.dtb \
+	sun8i-h3-nanopi-neo.dtb \
+	sun8i-h3-nanopi-neo-air.dtb \
+	sun8i-h3-nanopi-r1.dtb \
+	sun8i-h3-orangepi-2.dtb \
+	sun8i-h3-orangepi-lite.dtb \
+	sun8i-h3-orangepi-one.dtb \
+	sun8i-h3-orangepi-pc.dtb \
+	sun8i-h3-orangepi-pc-plus.dtb \
+	sun8i-h3-orangepi-plus.dtb \
+	sun8i-h3-orangepi-plus2e.dtb \
+	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-rervision-dvk.dtb \
+	sun8i-h3-zeropi.dtb \
+	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
+	sun8i-r16-bananapi-m2m.dtb \
+	sun8i-r16-nintendo-nes-classic.dtb \
+	sun8i-r16-nintendo-super-nes-classic.dtb \
+	sun8i-r16-parrot.dtb \
+	sun8i-r40-bananapi-m2-ultra.dtb \
+	sun8i-r40-oka40i-c.dtb \
+	sun8i-s3-elimo-initium.dtb \
+	sun8i-s3-lichee-zero-plus.dtb \
+	sun8i-s3-pinecube.dtb \
+	sun8i-t113s-mangopi-mq-r-t113.dtb \
+	sun8i-t3-cqa3t-bv3.dtb \
+	sun8i-v3-sl631-imx179.dtb \
+	sun8i-v3s-anbernic-rg-nano.dtb \
+	sun8i-v3s-licheepi-zero.dtb \
+	sun8i-v3s-licheepi-zero-dock.dtb \
+	sun8i-v40-bananapi-m2-berry.dtb
+dtb-$(CONFIG_MACH_SUN8I) += \
+	sun8i-a23-evb.dtb \
+	sun8i-a23-gt90h-v4.dtb \
+	sun8i-a23-inet86dz.dtb \
+	sun8i-a23-ippo-q8h-v5.dtb \
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-a23-polaroid-mid2407pxe03.dtb \
+	sun8i-a23-polaroid-mid2809pxe04.dtb \
+	sun8i-a23-q8-tablet.dtb \
+	sun8i-a33-et-q8-v1.6.dtb \
+	sun8i-a33-ga10h-v1.1.dtb \
+	sun8i-a33-inet-d978-rev2.dtb \
+	sun8i-a33-ippo-q8h-v1.2.dtb \
+	sun8i-a33-olinuxino.dtb \
+	sun8i-a33-q8-tablet.dtb \
+	sun8i-a33-sinlinx-sina33.dtb \
+	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-bananapi-m3.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
+	sun8i-a83t-tbs-a711.dtb \
+	sun8i-h2-plus-bananapi-m2-zero.dtb \
+	sun8i-h2-plus-libretech-all-h3-cc.dtb \
+	sun8i-h2-plus-orangepi-r1.dtb \
+	sun8i-h2-plus-orangepi-zero.dtb \
+	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
+	sun8i-h3-beelink-x2.dtb \
+	sun8i-h3-libretech-all-h3-cc.dtb \
+	sun8i-h3-mapleboard-mp130.dtb \
+	sun8i-h3-nanopi-duo2.dtb \
+	sun8i-h3-nanopi-m1.dtb\
+	\
+	sun8i-h3-nanopi-m1-plus.dtb \
+	sun8i-h3-nanopi-neo.dtb \
+	sun8i-h3-nanopi-neo-air.dtb \
+	sun8i-h3-nanopi-r1.dtb \
+	sun8i-h3-orangepi-2.dtb \
+	sun8i-h3-orangepi-lite.dtb \
+	sun8i-h3-orangepi-one.dtb \
+	sun8i-h3-orangepi-pc.dtb \
+	sun8i-h3-orangepi-pc-plus.dtb \
+	sun8i-h3-orangepi-plus.dtb \
+	sun8i-h3-orangepi-plus2e.dtb \
+	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-rervision-dvk.dtb \
+	sun8i-h3-zeropi.dtb \
+	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
+	sun8i-r16-bananapi-m2m.dtb \
+	sun8i-r16-nintendo-nes-classic.dtb \
+	sun8i-r16-nintendo-super-nes-classic.dtb \
+	sun8i-r16-parrot.dtb \
+	sun8i-r40-bananapi-m2-ultra.dtb \
+	sun8i-r40-oka40i-c.dtb \
+	sun8i-s3-elimo-initium.dtb \
+	sun8i-s3-lichee-zero-plus.dtb \
+	sun8i-s3-pinecube.dtb \
+	sun8i-t113s-mangopi-mq-r-t113.dtb \
+	sun8i-t3-cqa3t-bv3.dtb \
+	sun8i-v3-sl631-imx179.dtb \
+	sun8i-v3s-licheepi-zero.dtb \
+	sun8i-v3s-licheepi-zero-dock.dtb \
+	sun8i-v40-bananapi-m2-berry.dtb
+dtb-$(CONFIG_MACH_SUN9I) += \
+	sun9i-a80-optimus.dtb \
+	sun9i-a80-cubieboard4.dtb
+dtb-$(CONFIG_MACH_SUNIV) += \
+	suniv-f1c100s-licheepi-nano.dtb \
+	suniv-f1c200s-lctech-pi.dtb \
+	suniv-f1c200s-popstick-v1.1.dtb
+dtb-$(CONFIG_MACH_SUNIV) += \
+	suniv-f1c100s-licheepi-nano.dtb \
+	suniv-f1c200s-lctech-pi.dtb \
+	suniv-f1c200s-popstick-v1.1.dtb
diff --git a/arch/arm/boot/dts/axp152.dtsi b/arch/arm/boot/dts/allwinner/axp152.dtsi
index f90ad6c64a07..f90ad6c64a07 100644
--- a/arch/arm/boot/dts/axp152.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp152.dtsi
diff --git a/arch/arm/boot/dts/axp209.dtsi b/arch/arm/boot/dts/allwinner/axp209.dtsi
index 0d9ff12bdf28..469d0f7d5185 100644
--- a/arch/arm/boot/dts/axp209.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp209.dtsi
@@ -48,12 +48,19 @@
  * http://dl.linux-sunxi.org/AXP/AXP209%20Datasheet%20v1.0_cn.pdf
  */
 
+/ {
+	pmic-temp {
+		compatible = "iio-hwmon";
+		io-channels = <&axp_adc 4>; /* Internal temperature */
+	};
+};
+
 &axp209 {
 	compatible = "x-powers,axp209";
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp202-ac-power-supply";
 		status = "disabled";
 	};
@@ -69,7 +76,7 @@
 		#gpio-cells = <2>;
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp209-battery-power-supply";
 		status = "disabled";
 	};
@@ -112,7 +119,7 @@
 		};
 	};
 
-	usb_power_supply: usb-power-supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp202-usb-power-supply";
 		status = "disabled";
 	};
diff --git a/arch/arm/boot/dts/axp223.dtsi b/arch/arm/boot/dts/allwinner/axp223.dtsi
index b91b6c1278c7..b91b6c1278c7 100644
--- a/arch/arm/boot/dts/axp223.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp223.dtsi
diff --git a/arch/arm/boot/dts/axp22x.dtsi b/arch/arm/boot/dts/allwinner/axp22x.dtsi
index 65a07a67aca9..f79650afd0a7 100644
--- a/arch/arm/boot/dts/axp22x.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp22x.dtsi
@@ -52,7 +52,7 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp221-ac-power-supply";
 		status = "disabled";
 	};
@@ -62,11 +62,17 @@
 		#io-channel-cells = <1>;
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp221-battery-power-supply";
 		status = "disabled";
 	};
 
+	axp_gpio: gpio {
+		compatible = "x-powers,axp221-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	regulators {
 		/* Default work frequency for buck regulators */
 		x-powers,dcdc-freq = <3000>;
@@ -163,7 +169,7 @@
 		};
 	};
 
-	usb_power_supply: usb_power_supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp221-usb-power-supply";
 		status = "disabled";
 	};
diff --git a/arch/arm/boot/dts/axp809.dtsi b/arch/arm/boot/dts/allwinner/axp809.dtsi
index ab8e5f2d9246..d134d4c00bd8 100644
--- a/arch/arm/boot/dts/axp809.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp809.dtsi
@@ -50,4 +50,11 @@
 	compatible = "x-powers,axp809";
 	interrupt-controller;
 	#interrupt-cells = <1>;
+
+	axp_gpio: gpio {
+		compatible = "x-powers,axp809-gpio",
+			     "x-powers,axp221-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };
diff --git a/arch/arm/boot/dts/axp81x.dtsi b/arch/arm/boot/dts/allwinner/axp81x.dtsi
index 1dfeeceabf4c..ebaf1c3ce8db 100644
--- a/arch/arm/boot/dts/axp81x.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp81x.dtsi
@@ -48,7 +48,7 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp813-ac-power-supply";
 		status = "disabled";
 	};
@@ -62,19 +62,9 @@
 		compatible = "x-powers,axp813-gpio";
 		gpio-controller;
 		#gpio-cells = <2>;
-
-		gpio0_ldo: gpio0-ldo {
-			pins = "GPIO0";
-			function = "ldo";
-		};
-
-		gpio1_ldo: gpio1-ldo {
-			pins = "GPIO1";
-			function = "ldo";
-		};
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp813-battery-power-supply";
 		status = "disabled";
 	};
@@ -144,15 +134,11 @@
 		};
 
 		reg_ldo_io0: ldo-io0 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gpio0_ldo>;
 			/* Disable by default to avoid conflicts with GPIO */
 			status = "disabled";
 		};
 
 		reg_ldo_io1: ldo-io1 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gpio1_ldo>;
 			/* Disable by default to avoid conflicts with GPIO */
 			status = "disabled";
 		};
@@ -172,7 +158,7 @@
 		};
 	};
 
-	usb_power_supply: usb-power-supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp813-usb-power-supply";
 	};
 };
diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-a1000.dts
index 8692b11a83c3..20f9ed244851 100644
--- a/arch/arm/boot/dts/sun4i-a10-a1000.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-a1000.dts
@@ -60,15 +60,26 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-0 {
 			label = "a1000:red:usr";
 			gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-1 {
 			label = "a1000:blue:pwr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -133,6 +144,20 @@
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-ba10-tvbox.dts
index 816d534ac093..816d534ac093 100644
--- a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-ba10-tvbox.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-chuwi-v7-cw0825.dts
index 74262988881c..74262988881c 100644
--- a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-chuwi-v7-cw0825.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-cubieboard.dts
index 6ca02e824acc..0645d6064235 100644
--- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-cubieboard.dts
@@ -75,12 +75,12 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_cubieboard>;
 
-		blue {
+		led-0 {
 			label = "cubieboard:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* LED1 */
 		};
 
-		green {
+		led-1 {
 			label = "cubieboard:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* LED2 */
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-dserve-dsrv9703c.dts
index 8ee3ff42bd55..63e77c05bfda 100644
--- a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-dserve-dsrv9703c.dts
@@ -62,6 +62,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-gemei-g9.dts
index ea7a59dcf8f9..ea7a59dcf8f9 100644
--- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-gemei-g9.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-hackberry.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-hackberry.dts
index 47dea0922501..47dea0922501 100644
--- a/arch/arm/boot/dts/sun4i-a10-hackberry.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-hackberry.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-hyundai-a7hd.dts
index bf2044bac42f..bf2044bac42f 100644
--- a/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-hyundai-a7hd.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-inet1.dts
index ca878384e902..60e432a0ef1c 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet1.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-inet1.dts
@@ -62,6 +62,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
diff --git a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-inet97fv2.dts
index 76016f2ca29d..76016f2ca29d 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-inet97fv2.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-inet9f-rev03.dts
index 0a562b2cc5bc..62e7aa587f89 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-inet9f-rev03.dts
@@ -63,7 +63,7 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <20>;
 
-		left-joystick-left {
+		event-left-joystick-left {
 			label = "Left Joystick Left";
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
@@ -71,7 +71,7 @@
 			gpios = <&pio 0 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA6 */
 		};
 
-		left-joystick-right {
+		event-left-joystick-right {
 			label = "Left Joystick Right";
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
@@ -79,7 +79,7 @@
 			gpios = <&pio 0 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA5 */
 		};
 
-		left-joystick-up {
+		event-left-joystick-up {
 			label = "Left Joystick Up";
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
@@ -87,7 +87,7 @@
 			gpios = <&pio 0 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA8 */
 		};
 
-		left-joystick-down {
+		event-left-joystick-down {
 			label = "Left Joystick Down";
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
@@ -95,7 +95,7 @@
 			gpios = <&pio 0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA9 */
 		};
 
-		right-joystick-left {
+		event-right-joystick-left {
 			label = "Right Joystick Left";
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
@@ -103,7 +103,7 @@
 			gpios = <&pio 0 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA1 */
 		};
 
-		right-joystick-right {
+		event-right-joystick-right {
 			label = "Right Joystick Right";
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
@@ -111,7 +111,7 @@
 			gpios = <&pio 0 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA0 */
 		};
 
-		right-joystick-up {
+		event-right-joystick-up {
 			label = "Right Joystick Up";
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
@@ -119,7 +119,7 @@
 			gpios = <&pio 0 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA3 */
 		};
 
-		right-joystick-down {
+		event-right-joystick-down {
 			label = "Right Joystick Down";
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
@@ -127,7 +127,7 @@
 			gpios = <&pio 0 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA4 */
 		};
 
-		dpad-left {
+		event-dpad-left {
 			label = "DPad Left";
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
@@ -135,7 +135,7 @@
 			gpios = <&pio 7 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH23 */
 		};
 
-		dpad-right {
+		event-dpad-right {
 			label = "DPad Right";
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
@@ -143,7 +143,7 @@
 			gpios = <&pio 7 24 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH24 */
 		};
 
-		dpad-up {
+		event-dpad-up {
 			label = "DPad Up";
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
@@ -151,7 +151,7 @@
 			gpios = <&pio 7 25 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH25 */
 		};
 
-		dpad-down {
+		event-dpad-down {
 			label = "DPad Down";
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
@@ -159,49 +159,49 @@
 			gpios = <&pio 7 26 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH26 */
 		};
 
-		x {
+		event-x {
 			label = "Button X";
 			linux,code = <BTN_X>;
 			gpios = <&pio 0 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA16 */
 		};
 
-		y {
+		event-y {
 			label = "Button Y";
 			linux,code = <BTN_Y>;
 			gpios = <&pio 0 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA14 */
 		};
 
-		a {
+		event-a {
 			label = "Button A";
 			linux,code = <BTN_A>;
 			gpios = <&pio 0 17 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA17 */
 		};
 
-		b {
+		event-b {
 			label = "Button B";
 			linux,code = <BTN_B>;
 			gpios = <&pio 0 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA15 */
 		};
 
-		select {
+		event-select {
 			label = "Select Button";
 			linux,code = <BTN_SELECT>;
 			gpios = <&pio 0 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA11 */
 		};
 
-		start {
+		event-start {
 			label = "Start Button";
 			linux,code = <BTN_START>;
 			gpios = <&pio 0 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA12 */
 		};
 
-		top-left {
+		event-top-left {
 			label = "Top Left Button";
 			linux,code = <BTN_TL>;
 			gpios = <&pio 7 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH22 */
 		};
 
-		top-right {
+		event-top-right {
 			label = "Top Right Button";
 			linux,code = <BTN_TR>;
 			gpios = <&pio 0 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA13 */
diff --git a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-itead-iteaduino-plus.dts
index d4e319d16aae..d4e319d16aae 100644
--- a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-itead-iteaduino-plus.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-jesurun-q5.dts
index 8a7b4c53d278..1aeb0bd5519e 100644
--- a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-jesurun-q5.dts
@@ -63,7 +63,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "q5:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;  /* PH20 */
 		};
diff --git a/arch/arm/boot/dts/sun4i-a10-marsboard.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-marsboard.dts
index a843e57530ed..81fdb217d339 100644
--- a/arch/arm/boot/dts/sun4i-a10-marsboard.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-marsboard.dts
@@ -62,22 +62,22 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red1 {
+		led-0 {
 			label = "marsboard:red1:usr";
 			gpios = <&pio 1 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		red2 {
+		led-1 {
 			label = "marsboard:red2:usr";
 			gpios = <&pio 1 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		red3 {
+		led-2 {
 			label = "marsboard:red3:usr";
 			gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		red4 {
+		led-3 {
 			label = "marsboard:red4:usr";
 			gpios = <&pio 1 8 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-mini-xplus.dts
index f9d74e21031d..f9d74e21031d 100644
--- a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-mini-xplus.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-mk802.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802.dts
index 059fe9c5d024..059fe9c5d024 100644
--- a/arch/arm/boot/dts/sun4i-a10-mk802.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-mk802ii.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802ii.dts
index 17dcdf031118..17dcdf031118 100644
--- a/arch/arm/boot/dts/sun4i-a10-mk802ii.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802ii.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-olinuxino-lime.dts
index 845f76824d57..83d283cf6633 100644
--- a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-olinuxino-lime.dts
@@ -74,7 +74,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxinolime>;
 
-		green {
+		led {
 			label = "a10-olinuxino-lime:green:usr";
 			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -91,12 +91,11 @@
 	/*
 	 * The A10-Lime is known to be unstable when running at 1008 MHz
 	 */
-	operating-points = <
-		/* kHz    uV */
-		912000  1350000
-		864000  1300000
-		624000  1250000
-		>;
+	operating-points =
+		/* kHz	  uV */
+		<912000	1350000>,
+		<864000	1300000>,
+		<624000	1250000>;
 };
 
 &de {
diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino.dts
index 83287b6c975e..a332d61fd561 100644
--- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino.dts
@@ -63,12 +63,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		tx {
+		led-0 {
 			label = "pcduino:green:tx";
 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
 		};
 
-		rx {
+		led-1 {
 			label = "pcduino:green:rx";
 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
 		};
@@ -77,19 +77,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
 		};
 
-		home {
+		key-home {
 			label = "Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
 		};
 
-		menu {
+		key-menu {
 			label = "Key Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino2.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino2.dts
index bc4f128965ed..bc4f128965ed 100644
--- a/arch/arm/boot/dts/sun4i-a10-pcduino2.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino2.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-pov-protab2-ips9.dts
index 24a3d23e1952..c32596947647 100644
--- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-pov-protab2-ips9.dts
@@ -62,6 +62,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
diff --git a/arch/arm/boot/dts/allwinner/sun4i-a10-topwise-a721.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-topwise-a721.dts
new file mode 100644
index 000000000000..3628f12d2521
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-topwise-a721.dts
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 Pascal Roeleven <dev@pascalroeleven.nl>
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Topwise A721";
+	compatible = "topwise,a721", "allwinner,sun4i-a10";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>;
+		power-supply = <&reg_vbat>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		brightness-levels = <0 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	panel {
+		compatible = "starry,kr070pe2t";
+		backlight = <&backlight>;
+		power-supply = <&reg_lcd_power>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&tcon0_out_panel>;
+			};
+		};
+	};
+
+	reg_lcd_power: reg-lcd-power {
+		compatible = "regulator-fixed";
+		regulator-name = "reg-lcd-power";
+		gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+		enable-active-high;
+	};
+
+	reg_vbat: reg-vbat {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	accelerometer@4c {
+		compatible = "fsl,mma7660";
+		reg = <0x4c>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		vcc-supply = <&reg_vcc3v3>;
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-571 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <571428>;
+	};
+
+	button-761 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <761904>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-ph-supply = <&reg_vcc3v3>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb0_vbus {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_panel: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&panel_input>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/allwinner/sun4i-a10.dtsi
index 4c268b70b735..51a6464aab9a 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10.dtsi
@@ -115,13 +115,12 @@
 			reg = <0x0>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000 1400000
-				912000	1350000
-				864000	1300000
-				624000	1250000
-				>;
+				<1008000 1400000>,
+				<912000	1350000>,
+				<864000	1300000>,
+				<624000	1250000>;
 			#cooling-cells = <2>;
 		};
 	};
@@ -143,7 +142,7 @@
 			trips {
 				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
-					temperature = <850000>;
+					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
@@ -198,7 +197,7 @@
 		default-pool {
 			compatible = "shared-dma-pool";
 			size = <0x6000000>;
-			alloc-ranges = <0x4a000000 0x6000000>;
+			alloc-ranges = <0x40000000 0x10000000>;
 			reusable;
 			linux,cma-default;
 		};
@@ -624,6 +623,16 @@
 			status = "disabled";
 		};
 
+		csi1: csi@1c1d000 {
+			compatible = "allwinner,sun4i-a10-csi1";
+			reg = <0x01c1d000 0x1000>;
+			interrupts = <43>;
+			clocks = <&ccu CLK_AHB_CSI1>, <&ccu CLK_DRAM_CSI1>;
+			clock-names = "bus", "ram";
+			resets = <&ccu RST_CSI1>;
+			status = "disabled";
+		};
+
 		spi3: spi@1c1f000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c1f000 0x1000>;
@@ -670,6 +679,31 @@
 				function = "can";
 			};
 
+			/omit-if-no-ref/
+			csi1_8bits_pg_pins: csi1-8bits-pg-pins {
+				pins = "PG0", "PG2", "PG3", "PG4", "PG5",
+				       "PG6", "PG7", "PG8", "PG9", "PG10",
+				       "PG11";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_24bits_ph_pins: csi1-24bits-ph-pins {
+				pins = "PH0", "PH1", "PH2", "PH3", "PH4",
+				       "PH5", "PH6", "PH7", "PH8", "PH9",
+				       "PH10", "PH11", "PH12", "PH13", "PH14",
+				       "PH15", "PH16", "PH17", "PH18", "PH19",
+				       "PH20", "PH21", "PH22", "PH23", "PH24",
+				       "PH25", "PH26", "PH27";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_clk_pg_pin: csi1-clk-pg-pin {
+				pins = "PG1";
+				function = "csi1";
+			};
+
 			emac_pins: emac0-pins {
 				pins = "PA0", "PA1", "PA2",
 				       "PA3", "PA4", "PA5", "PA6",
diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t003.dts
index 64d50fcfcd3a..04b0e6d28769 100644
--- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t003.dts
@@ -62,7 +62,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_t003>;
 
-		red {
+		led {
 			label = "t003-tv-dongle:red:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t004.dts
index 8af0eae2ddc1..667bc2dc1ea9 100644
--- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t004.dts
@@ -62,7 +62,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_t004>;
 
-		red {
+		led {
 			label = "t004-tv-dongle:red:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-a10s-mk802.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-mk802.dts
index 6e90ccb267aa..d0219404c231 100644
--- a/arch/arm/boot/dts/sun5i-a10s-mk802.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-mk802.dts
@@ -60,7 +60,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led {
 			label = "mk802:red:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
 		};
diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-olinuxino-micro.dts
index d6bb82c295f0..5832bb31fc51 100644
--- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-olinuxino-micro.dts
@@ -79,7 +79,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxino>;
 
-		green {
+		led {
 			label = "a10s-olinuxino-micro:green:usr";
 			gpios = <&pio 4 3 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-r7-tv-dongle.dts
index b2a49a216ebf..964360f0610a 100644
--- a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-r7-tv-dongle.dts
@@ -63,7 +63,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_r7>;
 
-		green {
+		led {
 			label = "r7-tv-dongle:green:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-wobo-i5.dts
index 1f74ba1634cc..ef8baa992687 100644
--- a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-wobo-i5.dts
@@ -62,7 +62,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led {
 			label = "a10s-wobo-i5:blue:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/allwinner/sun5i-a10s.dtsi
index 09c486b608b2..09c486b608b2 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s.dtsi
diff --git a/arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-difrnce-dit4350.dts
index 894c4c4f9a1f..894c4c4f9a1f 100644
--- a/arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-difrnce-dit4350.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-d709.dts
index a23bf24792ec..d059388d7252 100644
--- a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-d709.dts
@@ -61,6 +61,7 @@
 		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
+		power-supply = <&reg_vcc3v3>;
 		/* TODO: backlight uses axp gpio1 as enable pin */
 	};
 
diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-m712.dts
index b1e2afd9de52..b1e2afd9de52 100644
--- a/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-m712.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-hsg-h702.dts
index 9b9f2a574851..9b9f2a574851 100644
--- a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-hsg-h702.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-inet-98v-rev2.dts
index 439ae3b537df..439ae3b537df 100644
--- a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-inet-98v-rev2.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-licheepi-one.dts
index ba8d75b3c716..3a6c4bd0a44f 100644
--- a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-licheepi-one.dts
@@ -66,19 +66,19 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
-			label ="licheepi:red:usr";
+		led-0 {
+			label = "licheepi:red:usr";
 			gpios = <&pio 2 5 GPIO_ACTIVE_LOW>;
 		};
 
-		green {
-			label ="licheepi:green:usr";
+		led-1 {
+			label = "licheepi:green:usr";
 			gpios = <&pio 2 19 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		blue {
-			label ="licheepi:blue:usr";
+		led-2 {
+			label = "licheepi:blue:usr";
 			gpios = <&pio 2 4 GPIO_ACTIVE_LOW>;
 		};
 
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino-micro.dts
index 5df398d77238..bfe1075e62cc 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino-micro.dts
@@ -64,7 +64,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxinom>;
 
-		power {
+		led {
 			label = "a13-olinuxino-micro:green:power";
 			gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino.dts
index 39101228a755..fadeae3cd8bb 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino.dts
@@ -66,7 +66,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxino>;
 
-		power {
+		led {
 			gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-touch-lux-3.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-touch-lux-3.dts
new file mode 100644
index 000000000000..d60407772e5d
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-touch-lux-3.dts
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright 2019 Ondrej Jirman <megous@megous.com>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PocketBook Touch Lux 3";
+	compatible = "pocketbook,touch-lux-3", "allwinner,sun5i-a13";
+
+	aliases {
+		serial0 = &uart1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_vcc3v3>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+			default-state = "on";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		label = "GPIO Keys";
+
+		key-right {
+			label = "Right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&pio 6 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG9 */
+		};
+
+		key-left {
+			label = "Left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&pio 6 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG10 */
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-1v8-nor-ctp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_1v8_nor: regulator-nor {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-nor";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v8>;
+		regulator-always-on;
+	};
+
+	reg_1v8_ctp: regulator-ctp {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-ctp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&pio 2 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v8>;
+	};
+
+	reg_3v3_mmc0: regulator-mmc0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mmc0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+		vin-supply = <&reg_vcc3v3>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	status = "okay";
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* Touchpanel is connected here. */
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-200 {
+		label = "Home";
+		linux,code = <KEY_HOME>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_3v3_mmc0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pc_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd-int-pll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+	/* We need this otherwise the LDO3 would overload */
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pe_pins>, <&spi2_cs0_pe_pin>;
+	status = "okay";
+
+	epd_flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "macronix,mx25u4033", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_ldo3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-q8-tablet.dts
index f9fc1c8b60b8..f9fc1c8b60b8 100644
--- a/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-q8-tablet.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-utoo-p66.dts
index be486d28d04f..be486d28d04f 100644
--- a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-utoo-p66.dts
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/allwinner/sun5i-a13.dtsi
index ae04955fd9a3..3325ab07094a 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13.dtsi
@@ -48,7 +48,7 @@
 
 / {
 	thermal-zones {
-		cpu_thermal {
+		cpu-thermal {
 			/* milliseconds */
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
@@ -102,15 +102,14 @@
 
 &cpu0 {
 	clock-latency = <244144>; /* 8 32k periods */
-	operating-points = <
+	operating-points =
 		/* kHz	  uV */
-		1008000 1400000
-		912000	1350000
-		864000	1300000
-		624000	1200000
-		576000	1200000
-		432000	1200000
-		>;
+		<1008000 1400000>,
+		<912000 1350000>,
+		<864000 1300000>,
+		<624000 1200000>,
+		<576000 1200000>,
+		<432000 1200000>;
 	#cooling-cells = <2>;
 };
 
diff --git a/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts b/arch/arm/boot/dts/allwinner/sun5i-gr8-chip-pro.dts
index a32cde3e32eb..5c3562b85a5b 100644
--- a/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-gr8-chip-pro.dts
@@ -70,7 +70,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "chip-pro:white:status";
 			gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun5i-gr8-evb.dts b/arch/arm/boot/dts/allwinner/sun5i-gr8-evb.dts
index 4c20d731a9c6..f4fe258ef06d 100644
--- a/arch/arm/boot/dts/sun5i-gr8-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-gr8-evb.dts
@@ -71,7 +71,7 @@
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 10000 0>;
 		enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
-
+		power-supply = <&reg_vcc3v3>;
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 	};
diff --git a/arch/arm/boot/dts/sun5i-gr8.dtsi b/arch/arm/boot/dts/allwinner/sun5i-gr8.dtsi
index 98a8fd5e89e8..98a8fd5e89e8 100644
--- a/arch/arm/boot/dts/sun5i-gr8.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-gr8.dtsi
diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts b/arch/arm/boot/dts/allwinner/sun5i-r8-chip.dts
index 4bf4943d4eb7..4192c23848c3 100644
--- a/arch/arm/boot/dts/sun5i-r8-chip.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-r8-chip.dts
@@ -70,7 +70,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "chip:white:status";
 			gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -255,6 +255,12 @@
 	pinctrl-0 = <&uart3_pg_pins>,
 		    <&uart3_cts_rts_pg_pins>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&axp_gpio 3 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+	};
 };
 
 &usb_otg {
diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/allwinner/sun5i-r8.dtsi
index de35dbcd1191..de35dbcd1191 100644
--- a/arch/arm/boot/dts/sun5i-r8.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-r8.dtsi
diff --git a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sun5i-reference-design-tablet.dtsi
index 1a9926d71410..6847f66699ac 100644
--- a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-reference-design-tablet.dtsi
@@ -55,6 +55,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; /* AXP GPIO1 */
+		power-supply = <&reg_vcc3v0>;
 	};
 
 	chosen {
diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/allwinner/sun5i.dtsi
index 6befa236ba99..d7c7b454a11a 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i.dtsi
@@ -117,7 +117,7 @@
 		default-pool {
 			compatible = "shared-dma-pool";
 			size = <0x6000000>;
-			alloc-ranges = <0x4a000000 0x6000000>;
+			alloc-ranges = <0x40000000 0x10000000>;
 			reusable;
 			linux,cma-default;
 		};
@@ -185,7 +185,9 @@
 		mbus: dram-controller@1c01000 {
 			compatible = "allwinner,sun5i-a13-mbus";
 			reg = <0x01c01000 0x1000>;
-			clocks = <&ccu 99>;
+			clocks = <&ccu CLK_MBUS>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			dma-ranges = <0x00000000 0x40000000 0x20000000>;
 			#interconnect-cells = <1>;
 		};
@@ -275,6 +277,7 @@
 			compatible = "allwinner,sun5i-a13-tcon";
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <44>;
+			dmas = <&dma SUN4I_DMA_DEDICATED 14>;
 			resets = <&ccu RST_LCD>;
 			reset-names = "lcd";
 			clocks = <&ccu CLK_AHB_LCD>,
@@ -283,7 +286,7 @@
 			clock-names = "ahb",
 				      "tcon-ch0",
 				      "tcon-ch1";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			status = "disabled";
 
@@ -514,6 +517,15 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			mmc2_4bit_pe_pins: mmc2-4bit-pe-pins {
+				pins = "PE4", "PE5", "PE6", "PE7",
+				       "PE8", "PE9";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			mmc2_8bit_pins: mmc2-8bit-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 				       "PC10", "PC11", "PC12", "PC13",
@@ -723,6 +735,18 @@
 			#size-cells = <0>;
 		};
 
+		mali: gpu@1c40000 {
+			compatible = "allwinner,sun4i-a10-mali", "arm,mali-400";
+			reg = <0x01c40000 0x10000>;
+			interrupts = <69>, <70>, <71>, <72>,  <73>;
+			interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pmu";
+			clocks = <&ccu CLK_AHB_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_GPU>;
+			assigned-clocks = <&ccu CLK_GPU>;
+			assigned-clock-rates = <320000000>;
+		};
+
 		timer@1c60000 {
 			compatible = "allwinner,sun5i-a13-hstimer";
 			reg = <0x01c60000 0x1000>;
@@ -770,9 +794,6 @@
 			interconnect-names = "dma-mem";
 			status = "disabled";
 
-			assigned-clocks = <&ccu CLK_DE_BE>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
diff --git a/arch/arm/boot/dts/sun6i-a31-app4-evb1.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-app4-evb1.dts
index 32d22025ac99..32d22025ac99 100644
--- a/arch/arm/boot/dts/sun6i-a31-app4-evb1.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-app4-evb1.dts
diff --git a/arch/arm/boot/dts/sun6i-a31-colombus.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-colombus.dts
index 93a15eaaa8cb..93a15eaaa8cb 100644
--- a/arch/arm/boot/dts/sun6i-a31-colombus.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-colombus.dts
diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-hummingbird.dts
index 049e6ab3cf56..236ebfc06192 100644
--- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-hummingbird.dts
@@ -154,7 +154,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
@@ -226,8 +226,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		x-powers,drive-vbus-en;
 	};
 };
diff --git a/arch/arm/boot/dts/sun6i-a31-i7.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-i7.dts
index 6cc8ccf53d88..744723d956f0 100644
--- a/arch/arm/boot/dts/sun6i-a31-i7.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-i7.dts
@@ -72,7 +72,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led {
 			label = "i7:blue:usr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-m9.dts
index a645c8f4257c..7d2eaaf5c33e 100644
--- a/arch/arm/boot/dts/sun6i-a31-m9.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-m9.dts
@@ -61,7 +61,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led {
 			label = "m9:blue:pwr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -115,8 +115,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-mele-a1000g-quad.dts
index 648f24746234..83611434270c 100644
--- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-mele-a1000g-quad.dts
@@ -61,7 +61,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led {
 			label = "a1000g:blue:pwr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -115,8 +115,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/allwinner/sun6i-a31.dtsi
index 2cf34ae1c17b..5cce4918f84c 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31.dtsi
@@ -46,6 +46,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 #include <dt-bindings/clock/sun6i-a31-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/reset/sun6i-a31-ccu.h>
 
 / {
@@ -105,13 +106,12 @@
 			reg = <0>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000	1200000
-				864000	1200000
-				720000	1100000
-				480000	1000000
-				>;
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
 			#cooling-cells = <2>;
 		};
 
@@ -121,13 +121,12 @@
 			reg = <1>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000	1200000
-				864000	1200000
-				720000	1100000
-				480000	1000000
-				>;
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
 			#cooling-cells = <2>;
 		};
 
@@ -137,13 +136,12 @@
 			reg = <2>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000	1200000
-				864000	1200000
-				720000	1100000
-				480000	1000000
-				>;
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
 			#cooling-cells = <2>;
 		};
 
@@ -153,19 +151,18 @@
 			reg = <3>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				1008000	1200000
-				864000	1200000
-				720000	1100000
-				480000	1000000
-				>;
+				<1008000 1200000>,
+				<864000 1200000>,
+				<720000 1100000>,
+				<480000 1000000>;
 			#cooling-cells = <2>;
 		};
 	};
 
 	thermal-zones {
-		cpu_thermal {
+		cpu-thermal {
 			/* milliseconds */
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
@@ -285,14 +282,19 @@
 			compatible = "allwinner,sun6i-a31-tcon";
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&ccu RST_AHB1_LCD0>;
-			reset-names = "lcd";
+			dmas = <&dma 11>;
+			resets = <&ccu RST_AHB1_LCD0>,
+				 <&ccu RST_AHB1_LVDS>;
+			reset-names = "lcd",
+				      "lvds";
 			clocks = <&ccu CLK_AHB1_LCD0>,
 				 <&ccu CLK_LCD0_CH0>,
-				 <&ccu CLK_LCD0_CH1>;
+				 <&ccu CLK_LCD0_CH1>,
+				 <&ccu 15>;
 			clock-names = "ahb",
 				      "tcon-ch0",
-				      "tcon-ch1";
+				      "tcon-ch1",
+				      "lvds-alt";
 			clock-output-names = "tcon0-pixel-clock";
 			#clock-cells = <0>;
 
@@ -334,14 +336,18 @@
 			compatible = "allwinner,sun6i-a31-tcon";
 			reg = <0x01c0d000 0x1000>;
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&ccu RST_AHB1_LCD1>;
-			reset-names = "lcd";
+			dmas = <&dma 12>;
+			resets = <&ccu RST_AHB1_LCD1>,
+				 <&ccu RST_AHB1_LVDS>;
+			reset-names = "lcd", "lvds";
 			clocks = <&ccu CLK_AHB1_LCD1>,
 				 <&ccu CLK_LCD1_CH0>,
-				 <&ccu CLK_LCD1_CH1>;
+				 <&ccu CLK_LCD1_CH1>,
+				 <&ccu 15>;
 			clock-names = "ahb",
 				      "tcon-ch0",
-				      "tcon-ch1";
+				      "tcon-ch1",
+				      "lvds-alt";
 			clock-output-names = "tcon1-pixel-clock";
 			#clock-cells = <0>;
 
@@ -593,7 +599,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun6i-a31-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -602,11 +608,13 @@
 		pio: pinctrl@1c20800 {
 			compatible = "allwinner,sun6i-a31-pinctrl";
 			reg = <0x01c20800 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -793,6 +801,7 @@
 		lradc: lradc@1c22800 {
 			compatible = "allwinner,sun4i-a10-lradc-keys";
 			reg = <0x01c22800 0x100>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -813,7 +822,7 @@
 			clocks = <&ccu CLK_APB2_UART0>;
 			resets = <&ccu RST_APB2_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -826,7 +835,7 @@
 			clocks = <&ccu CLK_APB2_UART1>;
 			resets = <&ccu RST_APB2_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -839,7 +848,7 @@
 			clocks = <&ccu CLK_APB2_UART2>;
 			resets = <&ccu RST_APB2_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -852,7 +861,7 @@
 			clocks = <&ccu CLK_APB2_UART3>;
 			resets = <&ccu RST_APB2_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -865,7 +874,7 @@
 			clocks = <&ccu CLK_APB2_UART4>;
 			resets = <&ccu RST_APB2_UART4>;
 			dmas = <&dma 10>, <&dma 10>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -878,7 +887,7 @@
 			clocks = <&ccu CLK_APB2_UART5>;
 			resets = <&ccu RST_APB2_UART5>;
 			dmas = <&dma 22>, <&dma 22>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -1130,9 +1139,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_BE1>;
 
-			assigned-clocks = <&ccu CLK_BE1>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1176,9 +1182,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_DRC1>;
 
-			assigned-clocks = <&ccu CLK_IEP_DRC1>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1222,9 +1225,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_BE0>;
 
-			assigned-clocks = <&ccu CLK_BE0>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1265,9 +1265,6 @@
 				      "ram";
 			resets = <&ccu RST_AHB1_DRC0>;
 
-			assigned-clocks = <&ccu CLK_IEP_DRC0>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1302,16 +1299,17 @@
 			#clock-cells = <1>;
 			compatible = "allwinner,sun6i-a31-rtc";
 			reg = <0x01f00000 0x54>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&osc32k>;
 			clock-output-names = "osc32k";
 		};
 
-		nmi_intc: interrupt-controller@1f00c00 {
+		r_intc: interrupt-controller@1f00c00 {
 			compatible = "allwinner,sun6i-a31-r-intc";
 			interrupt-controller;
-			#interrupt-cells = <2>;
+			#interrupt-cells = <3>;
 			reg = <0x01f00c00 0x400>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		};
@@ -1323,7 +1321,7 @@
 			ar100: ar100_clk {
 				compatible = "allwinner,sun6i-a31-ar100-clk";
 				#clock-cells = <0>;
-				clocks = <&rtc 0>, <&osc24M>,
+				clocks = <&rtc CLK_OSC32K>, <&osc24M>,
 					 <&ccu CLK_PLL_PERIPH>,
 					 <&ccu CLK_PLL_PERIPH>;
 				clock-output-names = "ar100";
@@ -1358,7 +1356,7 @@
 			ir_clk: ir_clk {
 				#clock-cells = <0>;
 				compatible = "allwinner,sun4i-a10-mod0-clk";
-				clocks = <&rtc 0>, <&osc24M>;
+				clocks = <&rtc CLK_OSC32K>, <&osc24M>;
 				clock-output-names = "ir";
 			};
 
@@ -1386,11 +1384,11 @@
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun6i-a31-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-colorfly-e708-q1.dts
index a2ef7846e2c8..a2ef7846e2c8 100644
--- a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-colorfly-e708-q1.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-cs908.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-cs908.dts
index 1d15e15011c6..1d15e15011c6 100644
--- a/arch/arm/boot/dts/sun6i-a31s-cs908.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-cs908.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-inet-q972.dts
index c5e2c55cdc63..c5e2c55cdc63 100644
--- a/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-inet-q972.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-primo81.dts
index bc3170a0b8b5..b32b70ada7fd 100644
--- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-primo81.dts
@@ -115,7 +115,6 @@
 		reg = <0x1c>;
 		interrupt-parent = <&pio>;
 		interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */
-		#io-channel-cells = <1>;
 	};
 };
 
@@ -159,8 +158,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		x-powers,drive-vbus-en;
 	};
 };
diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s-core.dtsi
index 3099491de8c4..227ad489731c 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s-core.dtsi
@@ -78,8 +78,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s.dts
index 0af48e143b66..56956352914d 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s.dts
@@ -67,7 +67,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "sina31s:status:usr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
 		};
diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-sinovoip-bpi-m2.dts
index 708caee52425..96554ab4f6d3 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-sinovoip-bpi-m2.dts
@@ -59,17 +59,17 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "bpi-m2:blue:usr";
 			gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
 		};
 
-		green {
+		led-1 {
 			label = "bpi-m2:green:usr";
 			gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
 		};
 
-		red {
+		led-2 {
 			label = "bpi-m2:red:usr";
 			gpios = <&pio 6 5 GPIO_ACTIVE_HIGH>; /* PG5 */
 		};
@@ -148,8 +148,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		x-powers,drive-vbus-en;
 	};
@@ -261,3 +261,74 @@
 &usbphy {
 	status = "okay";
 };
+
+&pio {
+	gpio-line-names =
+		/* PA */
+		"ETXD0", "ETXD1", "ETXD2", "ETXD3", "SDC0-DET", "", "",
+		"", "ETXCLK", "ETXEN", "EGTXCLK", "ERXD0", "ERXD1",
+		"ERXD2", "ERXD3", "", "", "", "", "ERXDV", "ERXCK",
+		"ETXERR", "ERXERR", "ECOL", "ECRS", "ECLKIN", "EMDC",
+		"EMDIO", "", "", "", "",
+
+		/* PB */
+		"CN7-P29", "CN7-P31", "CN7-P33", "CN7-P35", "CN7-P37",
+		"CN7-P28", "CN7-P27", "CN7-P32", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "",
+
+		/* PC */
+		"", "", "", "", "", "", "WL-SDIO-CMD", "WL-SDIO-CLK",
+		"WL-SDIO-D0", "WL-SDIO-D2", "WL-SDIO-D2", "WL-SDIO-D3",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"", "USB-DRV", "", "", "", "",
+
+		/* PD */
+		"CN9-P09", "CN9-P11", "CN9-P13", "CN9-P15", "CN9-P17",
+		"CN9-P19", "CN9-P21", "CN9-P23", "CN9-P25", "CN9-P27",
+		"CN9-P29", "CN9-P31", "CN9-P33", "CN9-P35", "CN9-P37",
+		"CN9-P39", "CN9-P40", "CN9-P38", "CN9-P36", "CN9-P34",
+		"CN9-P32", "CN9-P30", "CN9-P28", "CN9-P26", "CN9-P22",
+		"CN9-P14", "CN9-P18", "CN9-P16", "", "", "", "",
+
+		/* PE */
+		"CN6-P20", "CN6-P24", "CN6-P30", "CN6-P28", "CN7-P08",
+		"CN7-P10", "CN7-P36", "CN7-P38", "CN6-P17", "CN6-P19",
+		"CN6-P21", "CN6-P23", "CN6-P25", "CN6-P27", "CN6-P29",
+		"CN6-P31", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "",
+
+		/* PF */
+		"SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
+		"SDC0-D2", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"",
+
+		/* PG */
+		"CN9-P06", "CN9-P08", "CN9-P20", "CN9-P12", "CN9-P07",
+		"LED-PWR", "CN7-P13", "CN7-P11", "CN7-P22", "CN7-P15",
+		"LED-G", "LED-B", "CN7-P26", "CN7-P24", "CN7-P23",
+		"CN7-P19", "CN7-P21", "HCEC", "CN6-P22", "", "", "", "",
+		"", "", "", "", "", "", "", "", "",
+
+		/* PH */
+		"", "", "", "", "", "", "", "", "", "CN7-P07",
+		"CN7-P12", "CN7-P16", "CN7-P18", "CN9-P10", "CN6-P16",
+		"CN6-P14", "CN9-P04", "CN9-P02", "CN7-P05", "CN7-P03",
+		"CN8-P03", "CN8-P02", "", "", "CN6-P34", "CN6-P32",
+		"CN6-P26", "CN6-P18", "", "", "", "";
+};
+
+&r_pio {
+	gpio-line-names =
+		/* PL */
+		"PMU-SCK", "PMU-SDA", "VBAT-EN", "", "IR-RX",
+		"WL-WAKE-HOST", "BT-WAKE_HOST", "BT-ENABLE",
+		"WL-PMU-EN", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "",
+
+		/* PM */
+		"CN6-P12", "CN6-P35", "CN7-P40", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "";
+};
diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-yones-toptech-bs1078-v2.dts
index 2504e7189c54..0b61f5368d44 100644
--- a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-yones-toptech-bs1078-v2.dts
@@ -98,8 +98,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun6i-a31s.dtsi b/arch/arm/boot/dts/allwinner/sun6i-a31s.dtsi
index 97e2c51d0aea..97e2c51d0aea 100644
--- a/arch/arm/boot/dts/sun6i-a31s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s.dtsi
diff --git a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sun6i-reference-design-tablet.dtsi
index 7de2abd541c1..f38d19c6be8c 100644
--- a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-reference-design-tablet.dtsi
@@ -79,8 +79,8 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		drivevbus-supply = <&reg_vcc5v0>;
 		x-powers,drive-vbus-en;
 	};
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi-m1-plus.dts
index 32d5d45a35c0..caa935ca4f19 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi-m1-plus.dts
@@ -74,12 +74,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-0 {
 			label = "bananapi-m1-plus:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-1 {
 			label = "bananapi-m1-plus:pwr:usr";
 			gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -130,7 +130,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi.dts
index bb3987e101c2..46ecf9db2324 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi.dts
@@ -77,7 +77,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "bananapi:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
@@ -104,16 +104,15 @@
 
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
-	operating-points = <
+	operating-points =
 		/* kHz	  uV */
-		960000	1400000
-		912000	1400000
-		864000	1350000
-		720000	1250000
-		528000	1150000
-		312000	1100000
-		144000	1050000
-		>;
+		<960000	1400000>,
+		<912000	1400000>,
+		<864000	1350000>,
+		<720000	1250000>,
+		<528000	1150000>,
+		<312000	1100000>,
+		<144000	1050000>;
 };
 
 &de {
@@ -132,7 +131,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapro.dts
index 01ccff756996..e22f0e8bb17a 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapro.dts
@@ -63,12 +63,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "bananapro:blue:usr";
 			gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-1 {
 			label = "bananapro:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
@@ -110,7 +110,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-cubieboard2.dts
index b8203e4ef21c..e35e6990c4b2 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-cubieboard2.dts
@@ -75,12 +75,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "cubieboard2:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-1 {
 			label = "cubieboard2:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-cubietruck.dts
index 8c8dee6ea461..52160e368304 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-cubietruck.dts
@@ -75,22 +75,22 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "cubietruck:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		orange {
+		led-1 {
 			label = "cubietruck:orange:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		white {
+		led-2 {
 			label = "cubietruck:white:usr";
 			gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-3 {
 			label = "cubietruck:green:usr";
 			gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -151,7 +151,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-haoyu-marsboard.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-haoyu-marsboard.dts
new file mode 100644
index 000000000000..097e479c2772
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-haoyu-marsboard.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Conley Lee
+ * Conley Lee <conleylee@foxmail.com>
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "HAOYU Electronics Marsboard A20";
+	compatible = "haoyu,a20-marsboard", "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>, <&gmac_txerr>;
+	phy-handle = <&phy0>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
+	status = "okay";
+};
+
+&gmac_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	gmac_txerr: gmac-txerr-pin {
+		pins = "PA17";
+		function = "gmac";
+	};
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1450000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-hummingbird.dts
index 3def2a330598..3def2a330598 100644
--- a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-hummingbird.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-i12-tvbox.dts
index 358ed5f1b1c1..b21ddd0ec1c2 100644
--- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-i12-tvbox.dts
@@ -62,12 +62,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-0 {
 			label = "i12_tvbox:red:usr";
 			gpios = <&pio 7 9 GPIO_ACTIVE_LOW>;
 		};
 
-		blue {
+		led-1 {
 			label = "i12_tvbox:blue:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20-adb4006.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20-adb4006.dts
new file mode 100644
index 000000000000..577ead1d02a0
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20-adb4006.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+/dts-v1/;
+
+#include "sun7i-a20-icnova-a20.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "In-Circuit ICnova A20 ADB4006";
+	compatible = "incircuit,icnova-a20-adb4006", "incircuit,icnova-a20",
+		     "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20.dtsi b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20.dtsi
new file mode 100644
index 000000000000..46616c6bc899
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-swac.dts
index 413505f45a81..413505f45a81 100644
--- a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-swac.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-ibox.dts
index 946c27278321..8ff83016ff5a 100644
--- a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-ibox.dts
@@ -53,13 +53,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_itead_core>;
 
-		green {
+		led-0 {
 			label = "itead_core:green:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		blue {
+		led-1 {
 			label = "itead_core:blue:usr";
 			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-lamobo-r1.dts
index 17fa8901fc00..97518afe4658 100644
--- a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-lamobo-r1.dts
@@ -75,7 +75,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "lamobo_r1:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-linutronix-testbox-v2.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-linutronix-testbox-v2.dts
new file mode 100644
index 000000000000..da5a2eea4ce3
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-linutronix-testbox-v2.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2020 Linutronix GmbH
+ * Author: Benedikt Spranger <b.spranger@linutronix.de>
+ */
+
+/dts-v1/;
+#include "sun7i-a20-lamobo-r1.dts"
+
+/ {
+	model = "Lamobo R1";
+	compatible = "linutronix,testbox-v2", "lamobo,lamobo-r1", "allwinner,sun7i-a20";
+
+	leds {
+		led-opto1 {
+			label = "lamobo_r1:opto:powerswitch";
+			gpios = <&pio 7 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-opto2 {
+			label = "lamobo_r1:opto:relay";
+			gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		status = "okay";
+	};
+
+	atecc508a@60 {
+		compatible = "atmel,atecc508a";
+		reg = <0x60>;
+	};
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can_ph_pins>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-m3.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-m3.dts
index 6bff9e731fc3..f161d5238860 100644
--- a/arch/arm/boot/dts/sun7i-a20-m3.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-m3.dts
@@ -64,7 +64,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led {
 			label = "m3:blue:usr";
 			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sun7i-a20-mk808c.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-mk808c.dts
index 1491c603f661..1491c603f661 100644
--- a/arch/arm/boot/dts/sun7i-a20-mk808c.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-mk808c.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb-emmc.dts
index 20bf09b2226c..20bf09b2226c 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb.dts
index 6f9c54b8e49a..f05ee32bc9cb 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb.dts
@@ -75,7 +75,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "a20-olimex-som-evb:green:usr";
 			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb-emmc.dts
index a59755a2e7a9..a59755a2e7a9 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb.dts
index 230d62a6b8f1..54af6c18075b 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb.dts
@@ -46,19 +46,19 @@
 	leds {
 		compatible = "gpio-leds";
 
-		stat {
+		led-0 {
 			label = "a20-som204-evb:green:stat";
 			gpios = <&pio 8 0 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		led1 {
+		led-1 {
 			label = "a20-som204-evb:green:led1";
 			gpios = <&pio 8 10 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		led2 {
+		led-2 {
 			label = "a20-som204-evb:yellow:led2";
 			gpios = <&pio 8 11 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime-emmc.dts
new file mode 100644
index 000000000000..033cab3443f8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime-emmc.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Olimex Ltd.
+ *   Author: Stefan Mavrodiev <stefan@olimex.com>
+ */
+
+#include "sun7i-a20-olinuxino-lime.dts"
+
+/ {
+	model = "Olimex A20-OLinuXino-LIME-eMMC";
+	compatible = "olimex,a20-olinuxino-lime-emmc", "allwinner,sun7i-a20";
+
+	mmc2_pwrseq: pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&pio 2 16 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&mmc2_pwrseq>;
+	status = "okay";
+
+	emmc: emmc@0 {
+		reg = <0>;
+		compatible = "mmc-card";
+		broken-hpi;
+	};
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime.dts
index 2adbac860119..92938d022295 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime.dts
@@ -78,7 +78,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxinolime>;
 
-		green {
+		led {
 			label = "a20-olinuxino-lime:green:usr";
 			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2-emmc.dts
index decb014a382b..decb014a382b 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2.dts
index 9ba62774e89a..ecb91fb899ff 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2.dts
@@ -75,7 +75,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxinolime>;
 
-		green {
+		led {
 			label = "a20-olinuxino-lime2:green:usr";
 			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -112,7 +112,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro-emmc.dts
index 2337b44a88aa..2337b44a88aa 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
index 359bd0d5b3b1..a1b89b2a2999 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
@@ -82,7 +82,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_olinuxino>;
 
-		green {
+		led {
 			label = "a20-olinuxino-micro:green:usr";
 			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi-mini.dts
index 2e328d2cefc1..84efa01e7cba 100644
--- a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi-mini.dts
@@ -75,12 +75,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-0 {
 			label = "orangepi:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
 		};
 
-		blue {
+		led-1 {
 			label = "orangepi:blue:usr";
 			gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */
 		};
diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi.dts
index d75b2e2bab28..5d77f1d9818f 100644
--- a/arch/arm/boot/dts/sun7i-a20-orangepi.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi.dts
@@ -64,7 +64,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "orangepi:green:usr";
 			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
 		};
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3-nano.dts
index fce2f7fcd084..e40ecb48d726 100644
--- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3-nano.dts
@@ -1,5 +1,5 @@
 /*
- * Copyright 2015 Adam Sampson <ats@offog.org>
+ * Copyright 2015-2020 Adam Sampson <ats@offog.org>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -72,14 +72,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		/* Marked "LED3" on the PCB. */
-		usr1 {
+		led-3 {
 			label = "pcduino3-nano:green:usr1";
 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; /* PH16 */
 		};
 
-		/* Marked "LED4" on the PCB. */
-		usr2 {
+		led-4 {
 			label = "pcduino3-nano:green:usr2";
 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; /* PH15 */
 		};
@@ -115,7 +113,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3.dts
index cc8271d777b8..928b86a95f34 100644
--- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3.dts
@@ -64,12 +64,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		tx {
+		led-0 {
 			label = "pcduino3:green:tx";
 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
 		};
 
-		rx {
+		led-1 {
 			label = "pcduino3:green:rx";
 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
 		};
@@ -78,19 +78,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
 		};
 
-		home {
+		key-home {
 			label = "Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
 		};
 
-		menu {
+		key-menu {
 			label = "Key Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-wexler-tab7200.dts
index 6a66b0432dfa..fef02fcbbdf8 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-wexler-tab7200.dts
@@ -64,6 +64,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_vcc3v3>;
 	};
 
 	chosen {
diff --git a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-wits-pro-a20-dkt.dts
index 3bfae98f3cc3..3bfae98f3cc3 100644
--- a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-wits-pro-a20-dkt.dts
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/allwinner/sun7i-a20.dtsi
index 8aebefd6accf..5574299685ab 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20.dtsi
@@ -47,6 +47,7 @@
 #include <dt-bindings/dma/sun4i-a10.h>
 #include <dt-bindings/clock/sun7i-a20-ccu.h>
 #include <dt-bindings/reset/sun4i-a10-ccu.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -105,16 +106,15 @@
 			reg = <0>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				960000	1400000
-				912000	1400000
-				864000	1300000
-				720000	1200000
-				528000	1100000
-				312000	1000000
-				144000	1000000
-				>;
+				<960000	1400000>,
+				<912000	1400000>,
+				<864000	1300000>,
+				<720000	1200000>,
+				<528000	1100000>,
+				<312000	1000000>,
+				<144000	1000000>;
 			#cooling-cells = <2>;
 		};
 
@@ -124,22 +124,21 @@
 			reg = <1>;
 			clocks = <&ccu CLK_CPU>;
 			clock-latency = <244144>; /* 8 32k periods */
-			operating-points = <
+			operating-points =
 				/* kHz	  uV */
-				960000	1400000
-				912000	1400000
-				864000	1300000
-				720000	1200000
-				528000	1100000
-				312000	1000000
-				144000	1000000
-				>;
+				<960000	1400000>,
+				<912000	1400000>,
+				<864000	1300000>,
+				<720000	1200000>,
+				<528000	1100000>,
+				<312000	1000000>,
+				<144000	1000000>;
 			#cooling-cells = <2>;
 		};
 	};
 
 	thermal-zones {
-		cpu_thermal {
+		cpu-thermal {
 			/* milliseconds */
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
@@ -180,7 +179,7 @@
 		default-pool {
 			compatible = "shared-dma-pool";
 			size = <0x6000000>;
-			alloc-ranges = <0x4a000000 0x6000000>;
+			alloc-ranges = <0x40000000 0x10000000>;
 			reusable;
 			linux,cma-default;
 		};
@@ -404,11 +403,12 @@
 		};
 
 		tcon0: lcd-controller@1c0c000 {
-			compatible = "allwinner,sun7i-a20-tcon";
+			compatible = "allwinner,sun7i-a20-tcon0",
+				     "allwinner,sun7i-a20-tcon";
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&ccu RST_TCON0>;
-			reset-names = "lcd";
+			resets = <&ccu RST_TCON0>, <&ccu RST_LVDS>;
+			reset-names = "lcd", "lvds";
 			clocks = <&ccu CLK_AHB_LCD0>,
 				 <&ccu CLK_TCON0_CH0>,
 				 <&ccu CLK_TCON0_CH1>;
@@ -454,7 +454,8 @@
 		};
 
 		tcon1: lcd-controller@1c0d000 {
-			compatible = "allwinner,sun7i-a20-tcon";
+			compatible = "allwinner,sun7i-a20-tcon1",
+				     "allwinner,sun7i-a20-tcon";
 			reg = <0x01c0d000 0x1000>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&ccu RST_TCON1>;
@@ -729,6 +730,17 @@
 			status = "disabled";
 		};
 
+		csi1: csi@1c1d000 {
+			compatible = "allwinner,sun7i-a20-csi1",
+				     "allwinner,sun4i-a10-csi1";
+			reg = <0x01c1d000 0x1000>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_AHB_CSI1>, <&ccu CLK_DRAM_CSI1>;
+			clock-names = "bus", "ram";
+			resets = <&ccu RST_CSI1>;
+			status = "disabled";
+		};
+
 		spi3: spi@1c1f000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c1f000 0x1000>;
@@ -803,6 +815,31 @@
 			};
 
 			/omit-if-no-ref/
+			csi1_8bits_pg_pins: csi1-8bits-pg-pins {
+				pins = "PG0", "PG2", "PG3", "PG4", "PG5",
+				       "PG6", "PG7", "PG8", "PG9", "PG10",
+				       "PG11";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_24bits_ph_pins: csi1-24bits-ph-pins {
+				pins = "PH0", "PH1", "PH2", "PH3", "PH4",
+				       "PH5", "PH6", "PH7", "PH8", "PH9",
+				       "PH10", "PH11", "PH12", "PH13", "PH14",
+				       "PH15", "PH16", "PH17", "PH18", "PH19",
+				       "PH20", "PH21", "PH22", "PH23", "PH24",
+				       "PH25", "PH26", "PH27";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_clk_pg_pin: csi1-clk-pg-pin {
+				pins = "PG1";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
 			emac_pa_pins: emac-pa-pins {
 				pins = "PA0", "PA1", "PA2",
 				       "PA3", "PA4", "PA5", "PA6",
@@ -896,6 +933,20 @@
 			};
 
 			/omit-if-no-ref/
+			lcd_lvds0_pins: lcd-lvds0-pins {
+				pins = "PD0", "PD1", "PD2", "PD3", "PD4",
+				       "PD5", "PD6", "PD7", "PD8", "PD9";
+				function = "lvds0";
+			};
+
+			/omit-if-no-ref/
+			lcd_lvds1_pins: lcd-lvds1-pins {
+				pins = "PD10", "PD11", "PD12", "PD13", "PD14",
+				       "PD15", "PD16", "PD17", "PD18", "PD19";
+				function = "lvds1";
+			};
+
+			/omit-if-no-ref/
 			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2",
 				       "PF3", "PF4", "PF5";
diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi
index f292f96ab39b..cd4bf60dbb3c 100644
--- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi
@@ -44,6 +44,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
 #include <dt-bindings/reset/sun8i-a23-a33-ccu.h>
 
@@ -182,14 +183,19 @@
 			/* compatible gets set in SoC specific dtsi file */
 			reg = <0x01c0c000 0x1000>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma 12>;
 			clocks = <&ccu CLK_BUS_LCD>,
-				 <&ccu CLK_LCD_CH0>;
+				 <&ccu CLK_LCD_CH0>,
+				 <&ccu 13>;
 			clock-names = "ahb",
-				      "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+				      "tcon-ch0",
+				      "lvds-alt";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
-			resets = <&ccu RST_BUS_LCD>;
-			reset-names = "lcd";
+			resets = <&ccu RST_BUS_LCD>,
+				 <&ccu RST_BUS_LVDS>;
+			reset-names = "lcd",
+				      "lvds";
 			status = "disabled";
 
 			ports {
@@ -324,7 +330,7 @@
 
 		ccu: clock@1c20000 {
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -333,8 +339,10 @@
 		pio: pinctrl@1c20800 {
 			/* compatible gets set in SoC specific dtsi file */
 			reg = <0x01c20800 0x400>;
+			interrupt-parent = <&r_intc>;
 			/* interrupts get set in SoC specific dtsi file */
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -468,6 +476,7 @@
 		lradc: lradc@1c22800 {
 			compatible = "allwinner,sun4i-a10-lradc-keys";
 			reg = <0x01c22800 0x100>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -481,7 +490,7 @@
 			clocks = <&ccu CLK_BUS_UART0>;
 			resets = <&ccu RST_BUS_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -494,7 +503,7 @@
 			clocks = <&ccu CLK_BUS_UART1>;
 			resets = <&ccu RST_BUS_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -507,7 +516,7 @@
 			clocks = <&ccu CLK_BUS_UART2>;
 			resets = <&ccu RST_BUS_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -520,7 +529,7 @@
 			clocks = <&ccu CLK_BUS_UART3>;
 			resets = <&ccu RST_BUS_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -533,7 +542,7 @@
 			clocks = <&ccu CLK_BUS_UART4>;
 			resets = <&ccu RST_BUS_UART4>;
 			dmas = <&dma 10>, <&dma 10>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -679,9 +688,6 @@
 			clock-names = "ahb", "mod", "ram";
 			resets = <&ccu RST_BUS_DRC>;
 
-			assigned-clocks = <&ccu CLK_DRC>;
-			assigned-clock-rates = <300000000>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -707,6 +713,7 @@
 		rtc: rtc@1f00000 {
 			compatible = "allwinner,sun8i-a23-rtc";
 			reg = <0x01f00000 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			clock-output-names = "osc32k", "osc32k-out";
@@ -714,10 +721,10 @@
 			#clock-cells = <1>;
 		};
 
-		nmi_intc: interrupt-controller@1f00c00 {
+		r_intc: interrupt-controller@1f00c00 {
 			compatible = "allwinner,sun6i-a31-r-intc";
 			interrupt-controller;
-			#interrupt-cells = <2>;
+			#interrupt-cells = <3>;
 			reg = <0x01f00c00 0x400>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		};
@@ -803,10 +810,10 @@
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun8i-a23-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/sun8i-a23-evb.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-evb.dts
index 53fb1be0401a..53fb1be0401a 100644
--- a/arch/arm/boot/dts/sun8i-a23-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-evb.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-gt90h-v4.dts
index bcbc9b0758f9..bcbc9b0758f9 100644
--- a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-gt90h-v4.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-inet86dz.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-inet86dz.dts
index d4405752a414..d4405752a414 100644
--- a/arch/arm/boot/dts/sun8i-a23-inet86dz.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-inet86dz.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v1.2.dts
index c2f22fc33811..c2f22fc33811 120000
--- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v1.2.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v5.dts
index c2f22fc33811..c2f22fc33811 120000
--- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v5.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2407pxe03.dts
index d5f6aebd7216..d5f6aebd7216 100644
--- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2407pxe03.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2809pxe04.dts
index 9f9232a2fefb..9f9232a2fefb 100644
--- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2809pxe04.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-q8-tablet.dts
index 51097c77a152..51097c77a152 100644
--- a/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-q8-tablet.dts
diff --git a/arch/arm/boot/dts/sun8i-a23.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a23.dtsi
index a5e884a8b2ae..a5e884a8b2ae 100644
--- a/arch/arm/boot/dts/sun8i-a23.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23.dtsi
diff --git a/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-et-q8-v1.6.dts
index 4519fd791a8f..4519fd791a8f 120000
--- a/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-et-q8-v1.6.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-ga10h-v1.1.dts
index 2dfdd0a3151e..2dfdd0a3151e 100644
--- a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-ga10h-v1.1.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-inet-d978-rev2.dts
index 317763069c0a..065cb620aa99 100644
--- a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-inet-d978-rev2.dts
@@ -63,7 +63,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pin_d978>;
 
-		home {
+		led {
 			label = "d978:blue:home";
 			gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
 		};
diff --git a/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-ippo-q8h-v1.2.dts
index 4519fd791a8f..4519fd791a8f 120000
--- a/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-ippo-q8h-v1.2.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-olinuxino.dts
index 3d78169cdeed..6fee8f133508 100644
--- a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-olinuxino.dts
@@ -62,7 +62,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led {
 			label = "a33-olinuxino:green:usr";
 			gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -98,8 +98,8 @@
 	axp22x: pmic@3a3 {
 		compatible = "x-powers,axp223";
 		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		x-powers,drive-vbus-en;
 	};
@@ -194,8 +194,8 @@
 				    "Headphone", "Headphone Jack";
 	/* Board level routing. First 2 routes copied from SoC level */
 	simple-audio-card,routing =
-		"Left DAC", "AIF1 Slot 0 Left",
-		"Right DAC", "AIF1 Slot 0 Right",
+		"Left DAC", "DACL",
+		"Right DAC", "DACR",
 		"HP", "HPCOM",
 		"Headphone Jack", "HP",
 		"MIC1", "Microphone Jack",
diff --git a/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-q8-tablet.dts
index 9c5750c25613..9c5750c25613 100644
--- a/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-q8-tablet.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-sinlinx-sina33.dts
index 785798e3a104..0c82ff3c7cb4 100644
--- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-sinlinx-sina33.dts
@@ -63,6 +63,7 @@
 
 	panel {
 		compatible = "netron-dy,e231732";
+		power-supply = <&reg_vcc3v3>;
 
 		port {
 			panel_input: endpoint {
@@ -164,8 +165,8 @@
 	axp22x: pmic@3a3 {
 		compatible = "x-powers,axp223";
 		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a33.dtsi
index 1532a0e59af4..30fdd2703b1f 100644
--- a/arch/arm/boot/dts/sun8i-a33.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33.dtsi
@@ -46,7 +46,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -164,7 +164,7 @@
 		io-channels = <&ths>;
 	};
 
-	mali_opp_table: gpu-opp-table {
+	mali_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-144000000 {
@@ -189,8 +189,8 @@
 		simple-audio-card,mclk-fs = <128>;
 		simple-audio-card,aux-devs = <&codec_analog>;
 		simple-audio-card,routing =
-			"Left DAC", "AIF1 Slot 0 Left",
-			"Right DAC", "AIF1 Slot 0 Right";
+			"Left DAC", "DACL",
+			"Right DAC", "DACR";
 		status = "disabled";
 
 		simple-audio-card,cpu {
@@ -198,7 +198,7 @@
 		};
 
 		link_codec: simple-audio-card,codec {
-			sound-dai = <&codec>;
+			sound-dai = <&codec 0>;
 		};
 	};
 
@@ -215,7 +215,7 @@
 		};
 
 		crypto: crypto-engine@1c15000 {
-			compatible = "allwinner,sun4i-a10-crypto";
+			compatible = "allwinner,sun8i-a33-crypto";
 			reg = <0x01c15000 0x1000>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SS>, <&ccu CLK_SS>;
@@ -238,7 +238,7 @@
 		};
 
 		codec: codec@1c22e00 {
-			#sound-dai-cells = <0>;
+			#sound-dai-cells = <1>;
 			compatible = "allwinner,sun8i-a33-codec";
 			reg = <0x01c22e00 0x400>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
@@ -278,6 +278,7 @@
 		dphy: d-phy@1ca1000 {
 			compatible = "allwinner,sun6i-a31-mipi-dphy";
 			reg = <0x01ca1000 0x1000>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_MIPI_DSI>,
 				 <&ccu CLK_DSI_DPHY>;
 			clock-names = "bus", "mod";
@@ -288,7 +289,7 @@
 	};
 
 	thermal-zones {
-		cpu_thermal {
+		cpu-thermal {
 			/* milliseconds */
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
@@ -372,8 +373,6 @@
 		      "ram", "sat";
 	resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
 	reset-names = "be", "sat";
-	assigned-clocks = <&ccu CLK_DE_BE>;
-	assigned-clock-rates = <300000000>;
 };
 
 &ccu {
diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-allwinner-h8homlet-v2.dts
index 9c006fc18821..c31c97d16024 100644
--- a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-allwinner-h8homlet-v2.dts
@@ -122,7 +122,7 @@
 		compatible = "x-powers,axp818", "x-powers,axp813";
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		swin-supply = <&reg_dcdc1>;
 	};
@@ -142,7 +142,7 @@
 		ac100_rtc: rtc {
 			compatible = "x-powers,ac100-rtc";
 			interrupt-parent = <&r_intc>;
-			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&ac100_codec>;
 			#clock-cells = <1>;
 			clock-output-names = "cko1_rtc",
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3.dts
index 9d34eabba121..8d56b103f063 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3.dts
@@ -74,12 +74,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "bananapi-m3:blue:usr";
 			gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-1 {
 			label = "bananapi-m3:green:usr";
 			gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>;
 		};
@@ -105,6 +105,21 @@
 		/* enables internal regulator and de-asserts reset */
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
 	};
+
+	/*
+	 * Power supply for the SATA disk, behind a USB-SATA bridge.
+	 * Since it is a USB device, there is no consumer in the DT, so we
+	 * have to keep this always on.
+	 */
+	regulator-sata-disk-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "sata-disk-pwr";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
+	};
 };
 
 &cpu0 {
@@ -131,7 +146,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_sw>;
 	phy-handle = <&rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	allwinner,rx-delay-ps = <700>;
 	allwinner,tx-delay-ps = <700>;
 	status = "okay";
@@ -203,7 +218,7 @@
 		compatible = "x-powers,axp813";
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		fldoin-supply = <&reg_dcdc5>;
 		swin-supply = <&reg_dcdc1>;
@@ -225,7 +240,7 @@
 		ac100_rtc: rtc {
 			compatible = "x-powers,ac100-rtc";
 			interrupt-parent = <&r_intc>;
-			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&ac100_codec>;
 			#clock-cells = <1>;
 			clock-output-names = "cko1_rtc",
diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-cubietruck-plus.dts
index fb928503ad45..870993393fc2 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-cubietruck-plus.dts
@@ -74,22 +74,22 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "cubietruck-plus:blue:usr";
 			gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
 		};
 
-		orange {
+		led-1 {
 			label = "cubietruck-plus:orange:usr";
 			gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */
 		};
 
-		white {
+		led-2 {
 			label = "cubietruck-plus:white:usr";
 			gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */
 		};
 
-		green {
+		led-3 {
 			label = "cubietruck-plus:green:usr";
 			gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
 		};
@@ -101,7 +101,7 @@
 		initial-mode = <1>; /* initialize in HUB mode */
 		disabled-ports = <1>;
 		intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
-		reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
 		connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
 		refclk-frequency = <19200000>;
 	};
@@ -183,7 +183,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_dldo4>;
 	phy-handle = <&rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
@@ -239,7 +239,7 @@
 		compatible = "x-powers,axp818", "x-powers,axp813";
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		swin-supply = <&reg_dcdc1>;
 		x-powers,drive-vbus-en;
@@ -260,7 +260,7 @@
 		ac100_rtc: rtc {
 			compatible = "x-powers,ac100-rtc";
 			interrupt-parent = <&r_intc>;
-			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&ac100_codec>;
 			#clock-cells = <1>;
 			clock-output-names = "cko1_rtc",
diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-tbs-a711.dts
index 2fd31a0a0b34..a7d4ca308990 100644
--- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-tbs-a711.dts
@@ -65,7 +65,7 @@
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
 		enable-gpios = <&pio 3 29 GPIO_ACTIVE_HIGH>;
-
+		power-supply = <&reg_sw>;
 		brightness-levels = <0 1 2 4 8 16 32 64 128 255>;
 		default-brightness-level = <9>;
 	};
@@ -169,7 +169,7 @@
 	status = "okay";
 
 	touchscreen@38 {
-		compatible = "edt,edt-ft5x06";
+		compatible = "edt,edt-ft5206";
 		reg = <0x38>;
 		interrupt-parent = <&r_pio>;
 		interrupts = <0 7 IRQ_TYPE_EDGE_FALLING>; /* PL7 */
@@ -263,7 +263,7 @@
 		compatible = "x-powers,axp813";
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		swin-supply = <&reg_dcdc1>;
 		x-powers,drive-vbus-en;
 	};
@@ -283,7 +283,7 @@
 		ac100_rtc: rtc {
 			compatible = "x-powers,ac100-rtc";
 			interrupt-parent = <&r_intc>;
-			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&ac100_codec>;
 			#clock-cells = <1>;
 			clock-output-names = "cko1_rtc",
@@ -374,8 +374,8 @@
 };
 
 &reg_dldo3 {
-	regulator-min-microvolt = <2800000>;
-	regulator-max-microvolt = <2800000>;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
 	regulator-name = "vdd-csi";
 };
 
@@ -493,12 +493,12 @@
 };
 
 &usb_otg {
-	dr_mode = "otg";
 	status = "okay";
 };
 
 &usbphy {
-	usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+	usb0_id_det-gpios = <&pio 7 11 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH11 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_vmain>;
 	usb2_vbus-supply = <&reg_vmain>;
diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a83t.dtsi
index 53c38deb8a08..94eb3bfc989e 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t.dtsi
@@ -50,6 +50,7 @@
 #include <dt-bindings/reset/sun8i-a83t-ccu.h>
 #include <dt-bindings/reset/sun8i-de2.h>
 #include <dt-bindings/reset/sun8i-r-ccu.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -71,7 +72,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			clocks = <&ccu CLK_C0CPUX>;
@@ -82,7 +83,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			clocks = <&ccu CLK_C0CPUX>;
@@ -93,7 +94,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			clocks = <&ccu CLK_C0CPUX>;
@@ -115,7 +116,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@101 {
+		cpu101: cpu@101 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			clocks = <&ccu CLK_C1CPUX>;
@@ -126,7 +127,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@102 {
+		cpu102: cpu@102 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			clocks = <&ccu CLK_C1CPUX>;
@@ -137,7 +138,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@103 {
+		cpu103: cpu@103 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			clocks = <&ccu CLK_C1CPUX>;
@@ -199,7 +200,7 @@
 		status = "disabled";
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cluster0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -252,7 +253,7 @@
 		};
 	};
 
-	cpu1_opp_table: opp_table1 {
+	cpu1_opp_table: opp-table-cluster1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -313,7 +314,7 @@
 
 		display_clocks: clock@1000000 {
 			compatible = "allwinner,sun8i-a83t-de2-clk";
-			reg = <0x01000000 0x100000>;
+			reg = <0x01000000 0x10000>;
 			clocks = <&ccu CLK_BUS_DE>,
 				 <&ccu CLK_PLL_DE>;
 			clock-names = "bus",
@@ -323,6 +324,17 @@
 			#reset-cells = <1>;
 		};
 
+		rotate: rotate@1020000 {
+			compatible = "allwinner,sun8i-a83t-de2-rotate";
+			reg = <0x1020000 0x10000>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&display_clocks CLK_BUS_ROT>,
+				 <&display_clocks CLK_ROT>;
+			clock-names = "bus",
+				      "mod";
+			resets = <&display_clocks RST_ROT>;
+		};
+
 		mixer0: mixer@1100000 {
 			compatible = "allwinner,sun8i-a83t-de2-mixer-0";
 			reg = <0x01100000 0x100000>;
@@ -444,7 +456,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
 			clock-names = "ahb", "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
 			reset-names = "lcd", "lvds";
@@ -581,6 +593,12 @@
 		sid: eeprom@1c14000 {
 			compatible = "allwinner,sun8i-a83t-sid";
 			reg = <0x1c14000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ths_calibration: thermal-sensor-calibration@34 {
+				reg = <0x34 8>;
+			};
 		};
 
 		crypto: crypto@1c15000 {
@@ -592,6 +610,16 @@
 			clock-names = "bus", "mod";
 		};
 
+		msgbox: mailbox@1c17000 {
+			compatible = "allwinner,sun8i-a83t-msgbox",
+				     "allwinner,sun6i-a31-msgbox";
+			reg = <0x01c17000 0x1000>;
+			clocks = <&ccu CLK_BUS_MSGBOX>;
+			resets = <&ccu RST_BUS_MSGBOX>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
+		};
+
 		usb_otg: usb@1c19000 {
 			compatible = "allwinner,sun8i-a83t-musb",
 				     "allwinner,sun8i-a33-musb";
@@ -680,6 +708,7 @@
 
 		pio: pinctrl@1c20800 {
 			compatible = "allwinner,sun8i-a83t-pinctrl";
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
@@ -999,10 +1028,10 @@
 			reg = <0x01c30000 0x104>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
-			resets = <&ccu 13>;
-			reset-names = "stmmaceth";
-			clocks = <&ccu 27>;
+			clocks = <&ccu CLK_BUS_EMAC>;
 			clock-names = "stmmaceth";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
 			status = "disabled";
 
 			mdio: mdio {
@@ -1033,9 +1062,6 @@
 			clock-names = "bus", "mod", "ram";
 			resets = <&ccu RST_BUS_CSI>;
 			status = "disabled";
-
-			csi_in: port {
-			};
 		};
 
 		hdmi: hdmi@1ee0000 {
@@ -1086,7 +1112,7 @@
 			compatible = "allwinner,sun8i-a83t-r-intc",
 				     "allwinner,sun6i-a31-r-intc";
 			interrupt-controller;
-			#interrupt-cells = <2>;
+			#interrupt-cells = <3>;
 			reg = <0x01f00c00 0x400>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		};
@@ -1095,7 +1121,7 @@
 			compatible = "allwinner,sun8i-a83t-r-ccu";
 			reg = <0x01f01400 0x400>;
 			clocks = <&osc24M>, <&osc16Md512>, <&osc16M>,
-				 <&ccu 6>;
+				 <&ccu CLK_PLL_PERIPH>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -1122,6 +1148,7 @@
 		r_lradc: lradc@1f03c00 {
 			compatible = "allwinner,sun8i-a83t-r-lradc";
 			reg = <0x01f03c00 0x100>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
@@ -1129,6 +1156,7 @@
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun8i-a83t-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>,
 				 <&osc16Md512>;
@@ -1165,5 +1193,82 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
+
+		ths: thermal-sensor@1f04000 {
+			compatible = "allwinner,sun8i-a83t-ths";
+			reg = <0x01f04000 0x100>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			nvmem-cells = <&ths_calibration>;
+			nvmem-cell-names = "calibration";
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	thermal-zones {
+		cpu0_thermal: cpu0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 0>;
+
+			trips {
+				cpu0_hot: cpu-hot {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu0_very_hot: cpu-very-hot {
+					temperature = <100000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				cpu-hot-limit {
+					trip = <&cpu0_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu1_thermal: cpu1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 1>;
+
+			trips {
+				cpu1_hot: cpu-hot {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu1_very_hot: cpu-very-hot {
+					temperature = <100000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				cpu-hot-limit {
+					trip = <&cpu1_hot>;
+					cooling-device = <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpu_thermal: gpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 2>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..d729b7c705db
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ *   Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Banana Pi BPI-M2-Zero";
+	compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "c";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr_led {
+			label = "bananapi-m2-zero:red:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
+			default-state = "on";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		switch-4 {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	reg_vdd_cpux: vdd-cpux-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+
+		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+		enable-active-high;
+		gpios-states = <0x1>;
+		states = <1100000 0>, <1300000 1>;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	reg_vcc1v2: vcc1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	poweroff {
+		compatible = "regulator-poweroff";
+		cpu-supply = <&reg_vcc1v2>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	/*
+	 * On the production batch of this board the card detect GPIO is
+	 * high active (card inserted), although on the early samples it's
+	 * low active.
+	 */
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <1500000>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
+
+};
+
+&pio {
+	gpio-line-names =
+		/* PA */
+		"CON2-P13", "CON2-P11", "CON2-P22", "CON2-P15",
+			"CON3-P03", "CON3-P02", "CON2-P07", "CON2-P29",
+		"CON2-P31", "CON2-P33", "CON2-P35", "CON2-P05",
+			"CON2-P03", "CON2-P08", "CON2-P10", "CON2-P16",
+		"CON2-P12", "CON2-P37", "CON2-P28", "CON2-P27",
+			"CON2-P40", "CON2-P38", "", "",
+		"", "", "", "", "", "", "", "",
+
+		/* PB */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+
+		/* PC */
+		"CON2-P19", "CON2-P21", "CON2-P23", "CON2-P24",
+			"CON2-P18", "", "", "CON2-P26",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+
+		/* PD */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "CSI-PWR-EN", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+
+		/* PE */
+		"CN3-P17", "CN3-P13", "CN3-P09", "CN3-P07",
+			"CN3-P19", "CN3-P21", "CN3-P22", "CN3-P20",
+		"CN3-P18", "CN3-P16", "CN3-P14", "CN3-P12",
+			"CN3-P05", "CN3-P03", "CN3-P06", "CN3-P08",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+
+		/* PF */
+		"SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
+			"SDC0-D2", "SDC0-DET", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+
+		/* PG */
+		"WL-SDIO-CLK", "WL-SDIO-CMD", "WL-SDIO-D0", "WL-SDIO-D1",
+			"WL-SDIO-D2", "WL-SDIO-D3", "BT-UART-TX", "BT-UART-RX",
+		"BT-UART-RTS", "BT-UART-CTS", "WL-WAKE-AP", "BT-WAKE-AP",
+			"BT-RST-N", "AP-WAKE-BT", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&r_pio {
+	gpio-line-names =
+		/* PL */
+		"", "CPUX-SET", "CON2-P32", "POWER-KEY", "CON2-P36",
+			"VCC-IO-EN", "USB0-ID", "WL-PWR-EN",
+		"PWR-STB", "PWR-DRAM", "PWR-LED", "IR-RX", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	/*
+	 * There're two micro-USB connectors, one is power-only and another is
+	 * OTG. The Vbus of these two connectors are connected together, so
+	 * the external USB device will be powered just by the power input
+	 * from the power-only USB port.
+	 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-libretech-all-h3-cc.dts
index 4db0d4bb65eb..4db0d4bb65eb 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-libretech-all-h3-cc.dts
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-r1.dts
index 3356f4210d45..3356f4210d45 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-r1.dts
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
index f19ed981da9d..3706216ffb40 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
@@ -169,7 +169,7 @@
 	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 	};
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus-v1.2.dts
index fc4a8c3d084d..fc4a8c3d084d 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus-v1.2.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus.dts
index 195a75da13f1..195a75da13f1 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-beelink-x2.dts
index ac9e26b1d906..a6d38ecee141 100644
--- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-beelink-x2.dts
@@ -57,6 +57,12 @@
 		ethernet1 = &sdiowifi;
 	};
 
+	cec {
+		compatible = "cec-gpio";
+		cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */
+		hdmi-phandle = <&hdmi>;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -75,23 +81,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "beelink-x2:blue:pwr";
 			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
 			default-state = "on";
 		};
 
-		red {
+		led-1 {
 			label = "beelink-x2:red:standby";
 			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
-		clock-names = "ext_clock";
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
 	};
 
 	sound_spdif {
@@ -111,6 +121,13 @@
 		#sound-dai-cells = <0>;
 		compatible = "linux,spdif-dit";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+	};
 };
 
 &de {
@@ -143,6 +160,7 @@
 };
 
 &ir {
+	linux,rc-map-name = "rc-tanix-tx3mini";
 	pinctrl-names = "default";
 	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3-devboard.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3-devboard.dts
new file mode 100644
index 000000000000..02fbe00cde97
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3-devboard.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTS for Emlid Neutis N5 Dev board.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgiii.staroselskii@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3-emlid-neutis-n5h3.dtsi"
+
+/ {
+	model = "Emlid Neutis N5H3 Developer board";
+	compatible = "emlid,neutis-n5h3-devboard",
+		     "emlid,neutis-n5h3",
+		     "allwinner,sun8i-h3";
+
+	vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0>, <1300000 0x1>;
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpux>;
+};
+
+&codec {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3.dtsi b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3.dtsi
new file mode 100644
index 000000000000..35e71f46c197
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis N5 SoM.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3.dtsi"
+#include "sunxi-h3-h5-emlid-neutis.dtsi"
diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-libretech-all-h3-cc.dts
index a8b2f0f1c11d..a8b2f0f1c11d 100644
--- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-libretech-all-h3-cc.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-mapleboard-mp130.dts
index ff0a7a952e0c..f5c8ccc5b872 100644
--- a/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-mapleboard-mp130.dts
@@ -39,16 +39,16 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
 		};
 
-		user {
+		key-user {
 			label = "user";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-duo2.dts
index c73f59900975..343b02b97155 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-duo2.dts
@@ -25,22 +25,22 @@
 	leds {
 		compatible = "gpio-leds";
 
-		pwr {
+		led-0 {
 			label = "nanopi:red:pwr";
 			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
 			default-state = "on";
 		};
 
-		status {
+		led-1 {
 			label = "nanopi:green:status";
 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		k1 {
+		key-0 {
 			label = "k1";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
@@ -57,11 +57,10 @@
 		regulator-ramp-delay = <50>; /* 4ms */
 
 		enable-active-high;
-		enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
 		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
 		gpios-states = <0x1>;
-		states = <1100000 0x0
-			  1300000 0x1>;
+		states = <1100000 0>, <1300000 1>;
 	};
 
 	reg_vcc_dram: vcc-dram {
@@ -91,7 +90,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 
@@ -152,7 +151,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1-plus.dts
index 4ba533b0340f..4ba533b0340f 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1-plus.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1.dts
index 69243dcb30a6..69243dcb30a6 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
index 07867a0d569b..9e1a33f94cad 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
@@ -61,13 +61,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		pwr {
+		led-0 {
 			label = "nanopi:green:pwr";
 			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
 			default-state = "on";
 		};
 
-		status {
+		led-1 {
 			label = "nanopi:blue:status";
 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
 		};
@@ -103,12 +103,40 @@
 	};
 };
 
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
 &usbphy {
 	/* USB VBUS is always on */
 	status = "okay";
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo.dts
index 9f33f6fae595..df71fab3cf4e 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo.dts
@@ -45,6 +45,10 @@
 / {
 	model = "FriendlyARM NanoPi NEO";
 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+	};
 };
 
 &ehci0 {
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-r1.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-r1.dts
new file mode 100644
index 000000000000..42cd1131adf3
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-r1.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Igor Pecovnik <igor@armbian.com>
+ * Copyright (C) 2020 Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
+ * Copyright (C) 2020 Yu-Tung Chang <mtwget@gmail.com>
+*/
+
+#include "sun8i-h3-nanopi.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "FriendlyARM NanoPi R1";
+	compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3";
+
+	aliases {
+		serial1 = &uart1;
+		ethernet0 = &emac;
+		ethernet1 = &wifi;
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+	};
+
+	reg_vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>;
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0>,
+			 <1300000 0x1>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+	};
+
+	leds {
+		led-2 {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		};
+
+		led-3 {
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; /* PA9 */
+		};
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	wifi: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi.dtsi
index 4df29a65316d..cf8413fba6c1 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi.dtsi
@@ -60,27 +60,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "nanopi:blue:status";
 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		pwr {
+		led-1 {
 			label = "nanopi:green:pwr";
 			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "k1";
 
-		k1 {
+		key-0 {
 			label = "k1";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-2.dts
index 597c425d08ec..f1f9dbead32a 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-2.dts
@@ -88,19 +88,20 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw2 {
+		switch-2 {
 			label = "sw2";
 			linux,code = <BTN_1>;
 			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
 		};
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-lite.dts
index 6f9c97add54e..305b34a321f5 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-lite.dts
@@ -87,10 +87,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-one.dts
index 4759ba3f2986..59f6f6d5e7ca 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-one.dts
@@ -86,10 +86,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc-plus.dts
index 71fb73208939..babf4cf1b2f6 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc-plus.dts
@@ -53,11 +53,6 @@
 	};
 };
 
-&emac {
-	/* LEDs changed to active high on the plus */
-	/delete-property/ allwinner,leds-active-low;
-};
-
 &mmc1 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc.dts
index 5aff8ecc66cb..b96e015f54ee 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc.dts
@@ -86,13 +86,14 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus.dts
index 97f497854e05..d05fa679dcd3 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus.dts
@@ -85,7 +85,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus2e.dts
index 6dbf7b2e0c13..b6ca45d18e51 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus2e.dts
@@ -67,7 +67,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
index b8f46e2802fd..561ea1d2f861 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
@@ -70,6 +70,21 @@
 		};
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "orangepi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led-1 {
+			label = "orangepi:red:status";
+			gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	reg_vcc3v3: vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3";
@@ -88,6 +103,10 @@
 	status = "okay";
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &hdmi {
 	status = "okay";
 };
@@ -132,8 +151,27 @@
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
+
+&usb_otg {
+	/*
+	 * According to schematics CN1 MicroUSB port can be used to take
+	 * external 5V to power up the board VBUS. On the contrary CN1 MicroUSB
+	 * port cannot provide power externally even if the board is powered
+	 * via GPIO pins. It thus makes sense to force peripheral mode.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-rervision-dvk.dts
index 4738f3a9efe4..4738f3a9efe4 100644
--- a/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-rervision-dvk.dts
diff --git a/arch/arm/boot/dts/vf610m4-colibri.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-zeropi.dts
index d4bc0e3f2f11..7d3e7323b661 100644
--- a/arch/arm/boot/dts/vf610m4-colibri.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-zeropi.dts
@@ -1,7 +1,5 @@
 /*
- * Device tree for Colibri VF61 Cortex-M4 support
- *
- * Copyright (C) 2015 Stefan Agner
+ * Copyright (C) 2020 Yu-Tung Chang <mtwget@gmail.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -42,59 +40,46 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "vf610m4.dtsi"
+#include "sun8i-h3-nanopi.dtsi"
 
 / {
-	model = "VF610 Cortex-M4";
-	compatible = "fsl,vf610m4";
+	model = "FriendlyARM ZeroPi";
+	compatible = "friendlyarm,zeropi", "allwinner,sun8i-h3";
 
-	chosen {
-		bootargs = "clk_ignore_unused init=/linuxrc rw";
-		stdout-path = "serial2:115200";
+	aliases {
+		ethernet0 = &emac;
 	};
 
-	memory@8c000000 {
-		device_type = "memory";
-		reg = <0x8c000000 0x3000000>;
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
 	};
 };
 
-&gpio0 {
-	status = "disabled";
-};
-
-&gpio1 {
-	status = "disabled";
-};
-
-&gpio2 {
-	status = "disabled";
-};
-
-&gpio3 {
-	status = "disabled";
-};
-
-&gpio4 {
-	status = "disabled";
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
 };
 
-&uart2 {
+&emac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+
+	allwinner,leds-active-low;
 	status = "okay";
 };
 
-&iomuxc {
-	vf610-colibri {
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				VF610_PAD_PTD0__UART2_TX		0x21a2
-				VF610_PAD_PTD1__UART2_RX		0x21a1
-				VF610_PAD_PTD2__UART2_RTS		0x21a2
-				VF610_PAD_PTD3__UART2_CTS		0x21a1
-			>;
-		};
-	};
+&usb_otg {
+	status = "okay";
+	dr_mode = "host";
 };
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/allwinner/sun8i-h3.dtsi
index fe773c72a69b..eac2349a2380 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3.dtsi
@@ -41,9 +41,10 @@
  */
 
 #include "sunxi-h3-h5.dtsi"
+#include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -80,7 +81,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
@@ -90,7 +91,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
@@ -100,7 +101,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
@@ -111,6 +112,35 @@
 		};
 	};
 
+	gpu_opp_table: opp-table-gpu {
+		compatible = "operating-points-v2";
+
+		opp-120000000 {
+			opp-hz = /bits/ 64 <120000000>;
+		};
+
+		opp-312000000 {
+			opp-hz = /bits/ 64 <312000000>;
+		};
+
+		opp-432000000 {
+			opp-hz = /bits/ 64 <432000000>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -195,9 +225,51 @@
 			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
 			clock-names = "bus", "core";
 			resets = <&ccu RST_BUS_GPU>;
+			operating-points-v2 = <&gpu_opp_table>;
+		};
 
-			assigned-clocks = <&ccu CLK_GPU>;
-			assigned-clock-rates = <384000000>;
+		ths: thermal-sensor@1c25000 {
+			compatible = "allwinner,sun8i-h3-ths";
+			reg = <0x01c25000 0x400>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_THS>;
+			clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+			clock-names = "bus", "mod";
+			nvmem-cells = <&ths_calibration>;
+			nvmem-cell-names = "calibration";
+			#thermal-sensor-cells = <0>;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths>;
+
+			trips {
+				cpu_hot_trip: cpu-hot {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_very_hot_trip: cpu-very-hot {
+					temperature = <100000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				cpu-hot-limit {
+					trip = <&cpu_hot_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 };
@@ -210,6 +282,10 @@
 	compatible = "allwinner,sun8i-h3-de2-clk";
 };
 
+&mbus {
+	compatible = "allwinner,sun8i-h3-mbus";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun7i-a20-mmc";
 	clocks = <&ccu CLK_BUS_MMC0>,
diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/allwinner/sun8i-q8-common.dtsi
index 3d9a1524e17e..3d9a1524e17e 100644
--- a/arch/arm/boot/dts/sun8i-q8-common.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-q8-common.dtsi
diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-bananapi-m2m.dts
index e1c75f7fa3ca..bc394686fedb 100644
--- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-bananapi-m2m.dts
@@ -64,17 +64,17 @@
 	leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-0 {
 			label = "bpi-m2m:blue:usr";
 			gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;
 		};
 
-		green {
+		led-1 {
 			label = "bpi-m2m:green:usr";
 			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>;
 		};
 
-		red {
+		led-2 {
 			label = "bpi-m2m:red:power";
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
 			default-state = "on";
@@ -91,7 +91,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -163,8 +163,8 @@
 	axp22x: pmic@3a3 {
 		compatible = "x-powers,axp223";
 		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		x-powers,drive-vbus-en;
 	};
@@ -283,7 +283,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_dldo1>;
 		vddio-supply = <&reg_aldo3>;
diff --git a/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-nes-classic.dts
index 246dec5846a4..246dec5846a4 100644
--- a/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-nes-classic.dts
diff --git a/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-super-nes-classic.dts
index 80761d7904ec..80761d7904ec 100644
--- a/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-super-nes-classic.dts
diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-parrot.dts
index 4f48eec6b2ef..95543a9c2118 100644
--- a/arch/arm/boot/dts/sun8i-r16-parrot.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-parrot.dts
@@ -64,14 +64,14 @@
 	leds {
 		compatible = "gpio-leds";
 
-		led1 {
+		led-1 {
 			label = "parrot:led1:usr";
-			gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+			gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
 		};
 
-		led2 {
+		led-2 {
 			label = "parrot:led2:usr";
-			gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+			gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
 		};
 	};
 
@@ -164,8 +164,8 @@
 	axp22x: pmic@3a3 {
 		compatible = "x-powers,axp223";
 		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		drivevbus-supply = <&reg_vcc5v0>;
 		x-powers,drive-vbus-en;
 	};
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/allwinner/sun8i-r40-bananapi-m2-ultra.dts
index 42d62d1ba1dc..28197bbcb1d5 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-bananapi-m2-ultra.dts
@@ -43,6 +43,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -113,6 +114,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
@@ -129,7 +134,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_dc1sw>;
 	status = "okay";
 };
@@ -164,6 +169,10 @@
 
 #include "axp22x.dtsi"
 
+&ir0 {
+	status = "okay";
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
@@ -223,16 +232,16 @@
 };
 
 &reg_dc1sw {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-gmac-phy";
 };
 
 &reg_dcdc1 {
 	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-3v0";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
 };
 
 &reg_dcdc2 {
diff --git a/arch/arm/boot/dts/allwinner/sun8i-r40-cpu-opp.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40-cpu-opp.dtsi
new file mode 100644
index 000000000000..649928b361af
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-cpu-opp.dtsi
@@ -0,0 +1,52 @@
+/{
+	cpu0_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-720000000 {
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1000000 1000000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-912000000 {
+			opp-hz = /bits/ 64 <912000000>;
+			opp-microvolt = <1100000 1100000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1008000000 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <1160000 1160000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1104000000 {
+			opp-hz = /bits/ 64 <1104000000>;
+			opp-microvolt = <1240000 1240000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1300000 1300000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+	};
+};
+
+&cpu0 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu1 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu2 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu3 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-r40-feta40i.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40-feta40i.dtsi
new file mode 100644
index 000000000000..9f39b5a2bb35
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-feta40i.dtsi
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// Copyright (C) 2021 Ivan Uvarov <i.uvarov@cognitivepilot.com>
+// Based on the sun8i-r40-bananapi-m2-ultra.dts, which is:
+//  Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+//  Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp22x: pmic@34 {
+		compatible = "x-powers,axp221";
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp22x.dtsi"
+
+&mmc2 {
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_aldo2>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clk_out_a_pin>;
+	vcc-pa-supply = <&reg_dcdc1>;
+	vcc-pc-supply = <&reg_aldo2>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pf-supply = <&reg_dldo4>;
+	vcc-pg-supply = <&reg_dldo1>;
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pa";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_dldo4 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vdd2v5-sata";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd1v2-sata";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vcc-pe";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-r40-oka40i-c.dts b/arch/arm/boot/dts/allwinner/sun8i-r40-oka40i-c.dts
new file mode 100644
index 000000000000..0bd1336206b8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-oka40i-c.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// Copyright (C) 2021 Ivan Uvarov <i.uvarov@cognitivepilot.com>
+// Based on the sun8i-r40-bananapi-m2-ultra.dts, which is:
+//	Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+//	Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+/dts-v1/;
+#include "sun8i-r40-feta40i.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Forlinx OKA40i-C";
+	compatible = "forlinx,oka40i-c", "forlinx,feta40i-c", "allwinner,sun8i-r40";
+
+	aliases {
+		ethernet0 = &gmac;
+		serial0 = &uart0;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+		serial5 = &uart5; /* RS485 */
+		serial7 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-5 { /* this is how the leds are labeled on the board */
+			gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led-6 {
+			gpios = <&pio 8 15 GPIO_ACTIVE_LOW>; /* PI15 */
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+		};
+	};
+
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; // PB10 WIFI_EN
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "ext_clock";
+	};
+};
+
+&ahci {
+	ahci-supply = <&reg_dldo4>;
+	phy-supply = <&reg_eldo2>;
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_dcdc1>;
+	status = "okay";
+};
+
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 8 11 GPIO_ACTIVE_LOW>; // PI11
+	status = "okay";
+};
+
+&mmc3 {
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 8 10 GPIO_ACTIVE_LOW>; // PI10
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&reg_dc1sw {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&tcon_tv0 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pi_pins>, <&uart2_rts_cts_pi_pins>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pg_pins>;
+	status = "okay";
+};
+
+&uart5 { /* RS485 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_ph_pins>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pi_pins>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc5v0>;
+	usb2_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
index 421dfbbfd7ee..a5b1f1e3900d 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
@@ -42,10 +42,13 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-r40-ccu.h>
+#include <dt-bindings/clock/sun8i-tcon-top.h>
 #include <dt-bindings/reset/sun8i-r40-ccu.h>
 #include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	#address-cells = <1>;
@@ -78,28 +81,40 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -109,6 +124,46 @@
 		status = "disabled";
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu0-thermal {
+			/* milliseconds */
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 0>;
+
+			trips {
+				cpu_hot_trip: cpu-hot {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_very_hot_trip: cpu-very-hot {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				cpu-hot-limit {
+					trip = <&cpu_hot_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpu_thermal: gpu-thermal {
+			/* milliseconds */
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 1>;
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -118,7 +173,7 @@
 		display_clocks: clock@1000000 {
 			compatible = "allwinner,sun8i-r40-de2-clk",
 				     "allwinner,sun8i-h3-de2-clk";
-			reg = <0x01000000 0x100000>;
+			reg = <0x01000000 0x10000>;
 			clocks = <&ccu CLK_BUS_DE>,
 				 <&ccu CLK_DE>;
 			clock-names = "bus",
@@ -172,6 +227,48 @@
 			};
 		};
 
+		deinterlace: deinterlace@1400000 {
+			compatible = "allwinner,sun8i-r40-deinterlace",
+				     "allwinner,sun8i-h3-deinterlace";
+			reg = <0x01400000 0x20000>;
+			clocks = <&ccu CLK_BUS_DEINTERLACE>,
+				 <&ccu CLK_DEINTERLACE>,
+				 /*
+				  * NOTE: Contrary to what datasheet claims,
+				  * DRAM deinterlace gate doesn't exist and
+				  * it's shared with CSI1.
+				  */
+				 <&ccu CLK_DRAM_CSI1>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_DEINTERLACE>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			interconnects = <&mbus 9>;
+			interconnect-names = "dma-mem";
+		};
+
+		syscon: system-control@1c00000 {
+			compatible = "allwinner,sun8i-r40-system-control",
+				     "allwinner,sun4i-a10-system-control";
+			reg = <0x01c00000 0x30>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@1d00000 {
+				compatible = "mmio-sram";
+				reg = <0x01d00000 0xd0000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x01d00000 0xd0000>;
+
+				ve_sram: sram-section@0 {
+					compatible = "allwinner,sun8i-r40-sram-c1",
+						     "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x80000>;
+				};
+			};
+		};
+
 		nmi_intc: interrupt-controller@1c00030 {
 			compatible = "allwinner,sun7i-a20-sc-nmi";
 			interrupt-controller;
@@ -180,6 +277,71 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		dma: dma-controller@1c02000 {
+			compatible = "allwinner,sun8i-r40-dma",
+				     "allwinner,sun50i-a64-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>;
+			dma-channels = <16>;
+			dma-requests = <31>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
+		spi0: spi@1c05000 {
+			compatible = "allwinner,sun8i-r40-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c05000 0x1000>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@1c06000 {
+			compatible = "allwinner,sun8i-r40-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c06000 0x1000>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		csi0: csi@1c09000 {
+			compatible = "allwinner,sun8i-r40-csi0",
+				     "allwinner,sun7i-a20-csi0";
+			reg = <0x01c09000 0x1000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI0>, <&ccu CLK_CSI_SCLK>,
+				 <&ccu CLK_DRAM_CSI0>;
+			clock-names = "bus", "isp", "ram";
+			resets = <&ccu RST_BUS_CSI0>;
+			interconnects = <&mbus 5>;
+			interconnect-names = "dma-mem";
+			status = "disabled";
+		};
+
+		video-codec@1c0e000 {
+			compatible = "allwinner,sun8i-r40-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+			<&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_VE>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			allwinner,sram = <&ve_sram 1>;
+			interconnects = <&mbus 4>;
+			interconnect-names = "dma-mem";
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun8i-r40-mmc",
 				     "allwinner,sun50i-a64-mmc";
@@ -234,6 +396,8 @@
 			clock-names = "ahb", "mmc";
 			resets = <&ccu RST_BUS_MMC3>;
 			reset-names = "ahb";
+			pinctrl-0 = <&mmc3_pins>;
+			pinctrl-names = "default";
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -275,6 +439,29 @@
 			resets = <&ccu RST_BUS_CE>;
 		};
 
+		spi2: spi@1c17000 {
+			compatible = "allwinner,sun8i-r40-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c17000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI2>, <&ccu CLK_SPI2>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ahci: sata@1c18000 {
+			compatible = "allwinner,sun8i-r40-ahci";
+			reg = <0x01c18000 0x1000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SATA>, <&ccu CLK_SATA>;
+			resets = <&ccu RST_BUS_SATA>;
+			reset-names = "ahci";
+			status = "disabled";
+		};
+
 		ehci1: usb@1c19000 {
 			compatible = "allwinner,sun8i-r40-ehci", "generic-ehci";
 			reg = <0x01c19000 0x100>;
@@ -321,10 +508,23 @@
 			status = "disabled";
 		};
 
+		spi3: spi@1c1f000 {
+			compatible = "allwinner,sun8i-r40-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c1f000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI3>, <&ccu CLK_SPI3>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-r40-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -343,18 +543,43 @@
 			compatible = "allwinner,sun8i-r40-pinctrl";
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			can_ph_pins: can-ph-pins {
+				pins = "PH20", "PH21";
+				function = "can";
+			};
+
+			can_pa_pins: can-pa-pins {
+				pins = "PA16", "PA17";
+				function = "can";
+			};
+
 			clk_out_a_pin: clk-out-a-pin {
 				pins = "PI12";
 				function = "clk_out_a";
 			};
 
+			/omit-if-no-ref/
+			csi0_8bits_pins: csi0-8bits-pins {
+				pins = "PE0", "PE2", "PE3", "PE4", "PE5",
+				       "PE6", "PE7", "PE8", "PE9", "PE10",
+				       "PE11";
+				function = "csi0";
+			};
+
+			/omit-if-no-ref/
+			csi0_mclk_pin: csi0-mclk-pin {
+				pins = "PE1";
+				function = "csi0";
+			};
+
 			gmac_rgmii_pins: gmac-rgmii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 				       "PA4", "PA5", "PA6", "PA7",
@@ -373,6 +598,36 @@
 				function = "i2c0";
 			};
 
+			i2c1_pins: i2c1-pins {
+				pins = "PB18", "PB19";
+				function = "i2c1";
+			};
+
+			i2c2_pins: i2c2-pins {
+				pins = "PB20", "PB21";
+				function = "i2c2";
+			};
+
+			i2c3_pins: i2c3-pins {
+				pins = "PI0", "PI1";
+				function = "i2c3";
+			};
+
+			i2c4_pins: i2c4-pins {
+				pins = "PI2", "PI3";
+				function = "i2c4";
+			};
+
+			ir0_pins: ir0-pins {
+				pins = "PB4";
+				function = "ir0";
+			};
+
+			ir1_pins: ir1-pins {
+				pins = "PB23";
+				function = "ir1";
+			};
+
 			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2",
 				       "PF3", "PF4", "PF5";
@@ -398,20 +653,104 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			mmc3_pins: mmc3-pins {
+				pins = "PI4", "PI5", "PI6",
+				       "PI7", "PI8", "PI9";
+				function = "mmc3";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			/omit-if-no-ref/
+			spi0_pc_pins: spi0-pc-pins {
+				pins = "PC0", "PC1", "PC2";
+				function = "spi0";
+			};
+
+			/omit-if-no-ref/
+			spi0_cs0_pc_pin: spi0-cs0-pc-pin {
+				pins = "PC23";
+				function = "spi0";
+			};
+
+			/omit-if-no-ref/
+			spi1_pi_pins: spi1-pi-pins {
+				pins = "PI17", "PI18", "PI19";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
+			spi1_cs0_pi_pin: spi1-cs0-pi-pin {
+				pins = "PI16";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
+			spi1_cs1_pi_pin: spi1-cs1-pi-pin {
+				pins = "PI15";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
 			uart0_pb_pins: uart0-pb-pins {
 				pins = "PB22", "PB23";
 				function = "uart0";
 			};
 
+			/omit-if-no-ref/
+			uart2_pi_pins: uart2-pi-pins {
+				pins = "PI18", "PI19";
+				function = "uart2";
+			};
+
+			/omit-if-no-ref/
+			uart2_rts_cts_pi_pins: uart2-rts-cts-pi-pins{
+				pins = "PI16", "PI17";
+				function = "uart2";
+			};
+
+			/omit-if-no-ref/
 			uart3_pg_pins: uart3-pg-pins {
 				pins = "PG6", "PG7";
 				function = "uart3";
 			};
 
+			/omit-if-no-ref/
 			uart3_rts_cts_pg_pins: uart3-rts-cts-pg-pins {
 				pins = "PG8", "PG9";
 				function = "uart3";
 			};
+
+			/omit-if-no-ref/
+			uart4_pg_pins: uart4-pg-pins {
+				pins = "PG10", "PG11";
+				function = "uart4";
+			};
+
+			/omit-if-no-ref/
+			uart5_ph_pins: uart5-ph-pins {
+				pins = "PH6", "PH7";
+				function = "uart5";
+			};
+
+			/omit-if-no-ref/
+			uart7_pi_pins: uart7-pi-pins {
+				pins = "PI20", "PI21";
+				function = "uart7";
+			};
+		};
+
+		timer@1c20c00 {
+			compatible = "allwinner,sun4i-a10-timer";
+			reg = <0x01c20c00 0x90>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
 		};
 
 		wdt: watchdog@1c20c90 {
@@ -421,6 +760,82 @@
 			clocks = <&osc24M>;
 		};
 
+		ir0: ir@1c21800 {
+			compatible = "allwinner,sun8i-r40-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x01c21800 0x400>;
+			pinctrl-0 = <&ir0_pins>;
+			pinctrl-names = "default";
+			clocks = <&ccu CLK_BUS_IR0>, <&ccu CLK_IR0>;
+			clock-names = "apb", "ir";
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_IR0>;
+			status = "disabled";
+		};
+
+		ir1: ir@1c21c00 {
+			compatible = "allwinner,sun8i-r40-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x01c21c00 0x400>;
+			pinctrl-0 = <&ir1_pins>;
+			pinctrl-names = "default";
+			clocks = <&ccu CLK_BUS_IR1>, <&ccu CLK_IR1>;
+			clock-names = "apb", "ir";
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_IR1>;
+			status = "disabled";
+		};
+
+		i2s0: i2s@1c22000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-r40-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22000 0x400>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S0>;
+			dmas = <&dma 3>, <&dma 3>;
+			dma-names = "rx", "tx";
+		};
+
+		i2s1: i2s@1c22400 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-r40-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22400 0x400>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S1>;
+			dmas = <&dma 4>, <&dma 4>;
+			dma-names = "rx", "tx";
+		};
+
+		i2s2: i2s@1c22800 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-r40-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22800 0x400>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S2>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "rx", "tx";
+		};
+
+		ths: thermal-sensor@1c24c00 {
+			compatible = "allwinner,sun8i-r40-ths";
+			reg = <0x01c24c00 0x100>;
+			clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+			clock-names = "bus", "mod";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_THS>;
+			/* TODO: add nvmem-cells for calibration */
+			#thermal-sensor-cells = <1>;
+		};
+
 		uart0: serial@1c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
@@ -528,6 +943,8 @@
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C1>;
 			resets = <&ccu RST_BUS_I2C1>;
+			pinctrl-0 = <&i2c1_pins>;
+			pinctrl-names = "default";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -539,6 +956,8 @@
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C2>;
 			resets = <&ccu RST_BUS_I2C2>;
+			pinctrl-0 = <&i2c2_pins>;
+			pinctrl-names = "default";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -550,31 +969,55 @@
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C3>;
 			resets = <&ccu RST_BUS_I2C3>;
+			pinctrl-0 = <&i2c3_pins>;
+			pinctrl-names = "default";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
+		can0: can@1c2bc00 {
+			compatible = "allwinner,sun8i-r40-can";
+			reg = <0x01c2bc00 0x400>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CAN>;
+			resets = <&ccu RST_BUS_CAN>;
+			status = "disabled";
+		};
+
 		i2c4: i2c@1c2c000 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2c000 0x400>;
 			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C4>;
 			resets = <&ccu RST_BUS_I2C4>;
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		ahci: sata@1c18000 {
-			compatible = "allwinner,sun8i-r40-ahci";
-			reg = <0x01c18000 0x1000>;
-			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_SATA>, <&ccu CLK_SATA>;
-			resets = <&ccu RST_BUS_SATA>;
-			reset-names = "ahci";
-			status = "disabled";
-
+		mali: gpu@1c40000 {
+			compatible = "allwinner,sun8i-r40-mali", "arm,mali-400";
+			reg = <0x01c40000 0x10000>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gp",
+					  "gpmmu",
+					  "pp0",
+					  "ppmmu0",
+					  "pp1",
+					  "ppmmu1",
+					  "pmu";
+			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_BUS_GPU>;
 		};
 
 		gmac: ethernet@1c50000 {
@@ -596,6 +1039,16 @@
 			};
 		};
 
+		mbus: dram-controller@1c62000 {
+			compatible = "allwinner,sun8i-r40-mbus";
+			reg = <0x01c62000 0x1000>;
+			clocks = <&ccu 155>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			dma-ranges = <0x00000000 0x40000000 0x80000000>;
+			#interconnect-cells = <1>;
+		};
+
 		tcon_top: tcon-top@1c70000 {
 			compatible = "allwinner,sun8i-r40-tcon-top";
 			reg = <0x01c70000 0x1000>;
@@ -718,7 +1171,7 @@
 			compatible = "allwinner,sun8i-r40-tcon-tv";
 			reg = <0x01c73000 0x1000>;
 			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_TCON_TV0>, <&tcon_top 0>;
+			clocks = <&ccu CLK_BUS_TCON_TV0>, <&tcon_top CLK_TCON_TOP_TV0>;
 			clock-names = "ahb", "tcon-ch1";
 			resets = <&ccu RST_BUS_TCON_TV0>;
 			reset-names = "lcd";
@@ -761,7 +1214,7 @@
 			compatible = "allwinner,sun8i-r40-tcon-tv";
 			reg = <0x01c74000 0x1000>;
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_TCON_TV1>, <&tcon_top 1>;
+			clocks = <&ccu CLK_BUS_TCON_TV1>, <&tcon_top CLK_TCON_TOP_TV1>;
 			clock-names = "ahb", "tcon-ch1";
 			resets = <&ccu RST_BUS_TCON_TV1>;
 			reset-names = "lcd";
@@ -803,7 +1256,7 @@
 		gic: interrupt-controller@1c81000 {
 			compatible = "arm,gic-400";
 			reg = <0x01c81000 0x1000>,
-			      <0x01c82000 0x1000>,
+			      <0x01c82000 0x2000>,
 			      <0x01c84000 0x2000>,
 			      <0x01c86000 0x2000>;
 			interrupt-controller;
@@ -818,8 +1271,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI0>, <&ccu CLK_HDMI_SLOW>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
@@ -848,7 +1301,7 @@
 			compatible = "allwinner,sun8i-r40-hdmi-phy";
 			reg = <0x01ef0000 0x10000>;
 			clocks = <&ccu CLK_BUS_HDMI1>, <&ccu CLK_HDMI_SLOW>,
-				 <&ccu 7>, <&ccu 16>;
+				 <&ccu CLK_PLL_VIDEO0>, <&ccu CLK_PLL_VIDEO1>;
 			clock-names = "bus", "mod", "pll-0", "pll-1";
 			resets = <&ccu RST_BUS_HDMI0>;
 			reset-names = "phy";
@@ -856,6 +1309,15 @@
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sun8i-reference-design-tablet.dtsi
index b3d8b8f056cd..872d56caa9ce 100644
--- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-reference-design-tablet.dtsi
@@ -54,6 +54,7 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		power-supply = <&reg_dc1sw>;
 	};
 
 	chosen {
@@ -92,8 +93,8 @@
 	axp22x: pmic@3a3 {
 		compatible = "x-powers,axp223";
 		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 		drivevbus-supply = <&reg_vcc5v0>;
 		x-powers,drive-vbus-en;
diff --git a/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-impetus.dtsi b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-impetus.dtsi
new file mode 100644
index 000000000000..052b010a5607
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-impetus.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Matteo Scordino <matteo@elimo.io>
+ */
+
+/dts-v1/;
+#include "sun8i-v3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+	model = "Elimo Impetus SoM";
+	compatible = "elimo,impetus", "sochip,s3", "allwinner,sun8i-v3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-initium.dts b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-initium.dts
new file mode 100644
index 000000000000..039677c2cc65
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-initium.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Matteo Scordino <matteo@elimo.io>
+ */
+
+/dts-v1/;
+#include "sun8i-s3-elimo-impetus.dtsi"
+
+/ {
+	model = "Elimo Initium";
+	compatible = "elimo,initium", "elimo,impetus", "sochip,s3",
+		     "allwinner,sun8i-v3";
+
+	aliases {
+		serial1 = &uart1;
+	};
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pg_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-s3-lichee-zero-plus.dts
index d18192d51d1b..d18192d51d1b 100644
--- a/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-lichee-zero-plus.dts
diff --git a/arch/arm/boot/dts/allwinner/sun8i-s3-pinecube.dts b/arch/arm/boot/dts/allwinner/sun8i-s3-pinecube.dts
new file mode 100644
index 000000000000..20966e954eda
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-pinecube.dts
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2019 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+#include "sun8i-v3.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "PineCube IP Camera";
+	compatible = "pine64,pinecube", "sochip,s3", "allwinner,sun8i-v3";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "pine64:ir:led1";
+			gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
+		};
+
+		led2 {
+			label = "pine64:ir:led2";
+			gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */
+		};
+	};
+
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_wifi: vcc-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-wifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */
+		vin-supply = <&reg_dcdc3>;
+		startup-delay-us = <200000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&csi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&csi1_8bit_pins>;
+	status = "okay";
+
+	port {
+		csi1_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pe_pins>;
+	status = "okay";
+
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&csi1_mclk_pin>;
+		clocks = <&ccu CLK_CSI1_MCLK>;
+		clock-names = "xclk";
+
+		AVDD-supply = <&reg_ldo3>;
+		DOVDD-supply = <&reg_ldo3>;
+		DVDD-supply = <&reg_ldo4>;
+		reset-gpios = <&pio 4 23 GPIO_ACTIVE_LOW>; /* PE23 */
+		powerdown-gpios = <&pio 4 24 GPIO_ACTIVE_HIGH>; /* PE24 */
+
+		port {
+			ov5640_ep: endpoint {
+				remote-endpoint = <&csi1_ep>;
+				bus-width = <8>;
+				hsync-active = <1>; /* Active high */
+				vsync-active = <0>; /* Active low */
+				data-active = <1>;  /* Active high */
+				pclk-sample = <1>;  /* Rising */
+			};
+		};
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-200 {
+		label = "Setup";
+		linux,code = <KEY_SETUP>;
+		channel = <0>;
+		voltage = <190000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdc3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc_wifi>;
+	vqmmc-supply = <&reg_dcdc3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pd-supply = <&reg_dcdc3>;
+	vcc-pe-supply = <&reg_ldo3>;
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-sys-cpu-ephy";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-dovdd-2v8-csi";
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
+};
+
+&reg_ldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-mangopi-mq-r-t113.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-mangopi-mq-r-t113.dts
new file mode 100644
index 000000000000..8b3a75383816
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-mangopi-mq-r-t113.dts
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+
+#include "sun8i-t113s.dtsi"
+#include "sunxi-d1s-t113-mangopi-mq-r.dtsi"
+
+/ {
+	model = "MangoPi MQ-R-T113";
+	compatible = "widora,mangopi-mq-r-t113", "allwinner,sun8i-t113s";
+
+	aliases {
+		ethernet0 = &rtl8189ftv;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&mmc1 {
+	rtl8189ftv: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 = WL_WAKE_AP */
+		interrupt-names = "host-wake";
+	};
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-t113s.dtsi
new file mode 100644
index 000000000000..c7181308ae6f
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#define SOC_PERIPHERAL_IRQ(nr) GIC_SPI nr
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <riscv/allwinner/sunxi-d1s-t113.dtsi>
+#include <riscv/allwinner/sunxi-d1-t113.dtsi>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+			clocks = <&ccu CLK_CPUX>;
+			clock-names = "cpu";
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+			clocks = <&ccu CLK_CPUX>;
+			clock-names = "cpu";
+		};
+	};
+
+	gic: interrupt-controller@1c81000 {
+		compatible = "arm,gic-400";
+		reg = <0x03021000 0x1000>,
+		      <0x03022000 0x2000>,
+		      <0x03024000 0x2000>,
+		      <0x03026000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-controller;
+		#interrupt-cells = <3>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};
diff --git a/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts b/arch/arm/boot/dts/allwinner/sun8i-t3-cqa3t-bv3.dts
index 6931aaab2382..9f472521f4a4 100644
--- a/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-t3-cqa3t-bv3.dts
@@ -45,6 +45,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -88,6 +89,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3-sl631-imx179.dts b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631-imx179.dts
new file mode 100644
index 000000000000..117aeece4e55
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631-imx179.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2020 Paul Kocialkowski <contact@paulk.fr>
+ */
+
+#include "sun8i-v3-sl631.dtsi"
+
+/ {
+	model = "SL631 Action Camera with IMX179";
+	compatible = "allwinner,sl631-imx179", "allwinner,sl631",
+		     "allwinner,sun8i-v3";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3-sl631.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631.dtsi
new file mode 100644
index 000000000000..6f93f8c49f84
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631.dtsi
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2020 Paul Kocialkowski <contact@paulk.fr>
+ */
+
+/dts-v1/;
+
+#include "sun8i-v3.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "SL631 Action Camera";
+	compatible = "allwinner,sl631", "allwinner,sun8i-v3";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pb_pins>;
+	status = "okay";
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-174 {
+		label = "Down";
+		linux,code = <KEY_DOWN>;
+		channel = <0>;
+		voltage = <174603>;
+	};
+
+	button-384 {
+		label = "Up";
+		linux,code = <KEY_UP>;
+		channel = <0>;
+		voltage = <384126>;
+	};
+
+	button-593 {
+		label = "OK";
+		linux,code = <KEY_OK>;
+		channel = <0>;
+		voltage = <593650>;
+	};
+};
+
+&mmc0 {
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	bus-width = <4>;
+	vmmc-supply = <&reg_dcdc3>;
+	status = "okay";
+};
+
+&pio {
+	vcc-pd-supply = <&reg_dcdc3>;
+	vcc-pe-supply = <&reg_dcdc3>;
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-sys-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vdd-3v3";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pg_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3.dtsi
new file mode 100644
index 000000000000..186c30cbe6ee
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3.dtsi
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.io>
+ * Copyright (C) 2021 Tobias Schramm <t.schramm@manjaro.org>
+ */
+
+#include "sun8i-v3s.dtsi"
+
+/ {
+	soc {
+		i2s0: i2s@1c22000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-v3-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22000 0x400>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+			clock-names = "apb", "mod";
+			dmas = <&dma 3>, <&dma 3>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2s0_pins>;
+			resets = <&ccu RST_BUS_I2S0>;
+			status = "disabled";
+		};
+	};
+};
+
+&ccu {
+	compatible = "allwinner,sun8i-v3-ccu";
+};
+
+&codec_analog {
+	compatible = "allwinner,sun8i-v3-codec-analog",
+		     "allwinner,sun8i-h3-codec-analog";
+};
+
+&emac {
+	/delete-property/ phy-handle;
+	/delete-property/ phy-mode;
+};
+
+&mdio_mux {
+	external_mdio: mdio@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&pio {
+	compatible = "allwinner,sun8i-v3-pinctrl";
+
+	i2s0_pins: i2s0-pins {
+		pins = "PG10", "PG11", "PG12", "PG13";
+		function = "i2s";
+	};
+
+	uart1_pg_pins: uart1-pg-pins {
+		pins = "PG6", "PG7";
+		function = "uart1";
+	};
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
new file mode 100644
index 000000000000..f34dfdf1566d
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "sun8i-v3s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+	model = "Anbernic RG Nano";
+	compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s";
+
+	aliases {
+		rtc0 = &pcf8563;
+		rtc1 = &rtc;
+		serial0 = &uart0;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>;
+		default-brightness-level = <11>;
+		power-supply = <&reg_vcc5v0>;
+		pwms = <&pwm 0 40000 1>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		button-a {
+			gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-A";
+			linux,code = <BTN_EAST>;
+		};
+
+		button-b {
+			gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-B";
+			linux,code = <BTN_SOUTH>;
+		};
+
+		button-down {
+			gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-DOWN";
+			linux,code = <BTN_DPAD_DOWN>;
+		};
+
+		button-left {
+			gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-LEFT";
+			linux,code = <BTN_DPAD_LEFT>;
+		};
+
+		button-right {
+			gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-RIGHT";
+			linux,code = <BTN_DPAD_RIGHT>;
+		};
+
+		button-se {
+			gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-SELECT";
+			linux,code = <BTN_SELECT>;
+		};
+
+		button-st {
+			gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-START";
+			linux,code = <BTN_START>;
+		};
+
+		button-tl {
+			gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-L";
+			linux,code = <BTN_TL>;
+		};
+
+		button-tr {
+			gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-R";
+			linux,code = <BTN_TR>;
+		};
+
+		button-up {
+			gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-UP";
+			linux,code = <BTN_DPAD_UP>;
+		};
+
+		button-x {
+			gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-X";
+			linux,code = <BTN_NORTH>;
+		};
+
+		button-y {
+			gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-Y";
+			linux,code = <BTN_WEST>;
+		};
+	};
+};
+
+&codec {
+	allwinner,audio-routing = "Speaker", "HP",
+				  "MIC1", "Mic",
+				  "Mic", "HBIAS";
+	allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PF6 */
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	gpio_expander: gpio@20 {
+		compatible = "nxp,pcal6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */
+		vcc-supply = <&reg_vcc3v3>;
+	};
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5 */
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	spi0_no_miso_pins: spi0-no-miso-pins {
+		pins = "PC1", "PC2", "PC3";
+		function = "spi0";
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm0_pin>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-max-microvolt = <1250000>;
+	regulator-min-microvolt = <1250000>;
+	regulator-name = "vdd-cpu";
+};
+
+/* DCDC3 wired into every 3.3v input that isn't the RTC. */
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-max-microvolt = <3300000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-name = "vcc-io";
+};
+
+/* LDO1 wired into RTC, voltage is hard-wired at 3.3v. */
+&reg_ldo1 {
+	regulator-always-on;
+	regulator-name = "vcc-rtc";
+};
+
+/* LDO2 wired into VCC-PLL and audio codec. */
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-max-microvolt = <3000000>;
+	regulator-min-microvolt = <3000000>;
+	regulator-name = "vcc-pll";
+};
+
+/* LDO3, LDO4, and LDO5 unused. */
+&reg_ldo3 {
+	status = "disabled";
+};
+
+&reg_ldo4 {
+	status = "disabled";
+};
+
+/* RTC uses internal oscillator */
+&rtc {
+	/delete-property/ clocks;
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_no_miso_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	display@0 {
+		compatible = "saef,sftc154b", "panel-mipi-dbi-spi";
+		reg = <0>;
+		backlight = <&backlight>;
+		dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */
+		reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+		spi-max-frequency = <100000000>;
+
+		height-mm = <39>;
+		width-mm = <39>;
+
+		/* Set hb-porch to compensate for non-visible area */
+		panel-timing {
+			hactive = <240>;
+			vactive = <240>;
+			hback-porch = <80>;
+			vback-porch = <0>;
+			clock-frequency = <0>;
+			hfront-porch = <0>;
+			hsync-len = <0>;
+			vfront-porch = <0>;
+			vsync-len = <0>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG5 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero-dock.dts
index db5cd0b8574b..752ad05c8f83 100644
--- a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero-dock.dts
@@ -49,16 +49,18 @@
 	compatible = "licheepi,licheepi-zero-dock", "licheepi,licheepi-zero",
 		     "allwinner,sun8i-v3s";
 
+	aliases {
+		ethernet0 = &emac;
+	};
+
 	leds {
 		/* The LEDs use PG0~2 pins, which conflict with MMC1 */
 		status = "disabled";
 	};
 };
 
-&mmc1 {
-	broken-cd;
-	bus-width = <4>;
-	vmmc-supply = <&reg_vcc3v3>;
+&emac {
+	allwinner,leds-active-low;
 	status = "okay";
 };
 
@@ -94,3 +96,10 @@
 		voltage = <800000>;
 	};
 };
+
+&mmc1 {
+	broken-cd;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero.dts
index 2e4587d26ce5..2e4587d26ce5 100644
--- a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero.dts
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
index 23ba56df38f7..e8a04476b776 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
@@ -1,5 +1,6 @@
 /*
  * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ * Copyright (C) 2021 Tobias Schramm <t.schramm@manjaro.org>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -41,14 +42,31 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-v3s-ccu.h>
 #include <dt-bindings/reset/sun8i-v3s-ccu.h>
+#include <dt-bindings/clock/sun8i-de2.h>
 
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 	interrupt-parent = <&gic>;
 
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer-lcd {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "mixer0-lcd0";
+			clocks = <&display_clocks CLK_MIXER0>,
+				 <&ccu CLK_TCON0>;
+			status = "disabled";
+		};
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -105,7 +123,7 @@
 
 		display_clocks: clock@1000000 {
 			compatible = "allwinner,sun8i-v3s-de2-clk";
-			reg = <0x01000000 0x100000>;
+			reg = <0x01000000 0x10000>;
 			clocks = <&ccu CLK_BUS_DE>,
 				 <&ccu CLK_DE>;
 			clock-names = "bus",
@@ -123,8 +141,6 @@
 			clock-names = "bus",
 				      "mod";
 			resets = <&display_clocks 0>;
-			assigned-clocks = <&display_clocks 6>;
-			assigned-clock-rates = <150000000>;
 
 			ports {
 				#address-cells = <1>;
@@ -140,6 +156,33 @@
 			};
 		};
 
+		syscon: system-control@1c00000 {
+			compatible = "allwinner,sun8i-v3s-system-control",
+				     "allwinner,sun8i-h3-system-control";
+			reg = <0x01c00000 0xd0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		nmi_intc: interrupt-controller@1c000d0 {
+			compatible = "allwinner,sun8i-v3s-nmi",
+				     "allwinner,sun9i-a80-nmi";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x01c000d0 0x0c>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		dma: dma-controller@1c02000 {
+			compatible = "allwinner,sun8i-v3s-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
 		tcon0: lcd-controller@1c0c000 {
 			compatible = "allwinner,sun8i-v3s-tcon";
 			reg = <0x01c0c000 0x1000>;
@@ -148,7 +191,7 @@
 				 <&ccu CLK_TCON0>;
 			clock-names = "ahb",
 				      "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_TCON0>;
 			reset-names = "lcd";
@@ -236,6 +279,19 @@
 			#size-cells = <0>;
 		};
 
+		crypto@1c15000 {
+			compatible = "allwinner,sun8i-v3s-crypto",
+				     "allwinner,sun8i-a33-crypto";
+			reg = <0x01c15000 0x1000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>;
+			clock-names = "ahb", "mod";
+			dmas = <&dma 16>, <&dma 16>;
+			dma-names = "rx", "tx";
+			resets = <&ccu RST_BUS_CE>;
+			reset-names = "ahb";
+		};
+
 		usb_otg: usb@1c19000 {
 			compatible = "allwinner,sun8i-h3-musb";
 			reg = <0x01c19000 0x0400>;
@@ -263,10 +319,33 @@
 			#phy-cells = <1>;
 		};
 
+		ehci: usb@1c1a000 {
+			compatible = "allwinner,sun8i-v3s-ehci", "generic-ehci";
+			reg = <0x01c1a000 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
+			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci: usb@1c1a400 {
+			compatible = "allwinner,sun8i-v3s-ohci", "generic-ohci";
+			reg = <0x01c1a400 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-v3s-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -287,23 +366,61 @@
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			/omit-if-no-ref/
+			csi0_mclk_pin: csi0-mclk-pin {
+				pins = "PE20";
+				function = "csi_mipi";
+			};
+
+			/omit-if-no-ref/
+			csi1_8bit_pins: csi1-8bit-pins {
+				pins = "PE0", "PE2", "PE3", "PE8", "PE9",
+				       "PE10", "PE11", "PE12", "PE13", "PE14",
+				       "PE15";
+				function = "csi";
+			};
+
+			/omit-if-no-ref/
+			csi1_mclk_pin: csi1-mclk-pin {
+				pins = "PE1";
+				function = "csi";
+			};
+
 			i2c0_pins: i2c0-pins {
 				pins = "PB6", "PB7";
 				function = "i2c0";
 			};
 
+			/omit-if-no-ref/
+			i2c1_pb_pins: i2c1-pb-pins {
+				pins = "PB8", "PB9";
+				function = "i2c1";
+			};
+
+			/omit-if-no-ref/
+			i2c1_pe_pins: i2c1-pe-pins {
+				pins = "PE21", "PE22";
+				function = "i2c1";
+			};
+
 			uart0_pb_pins: uart0-pb-pins {
 				pins = "PB8", "PB9";
 				function = "uart0";
 			};
 
+			uart2_pins: uart2-pins {
+				pins = "PB0", "PB1";
+				function = "uart2";
+			};
+
 			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2", "PF3",
 				       "PF4", "PF5";
@@ -320,6 +437,18 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			pwm0_pin: pwm0-pin {
+				pins = "PB4";
+				function = "pwm0";
+			};
+
+			/omit-if-no-ref/
+			pwm1_pin: pwm1-pin {
+				pins = "PB5";
+				function = "pwm1";
+			};
+
 			spi0_pins: spi0-pins {
 				pins = "PC0", "PC1", "PC2", "PC3";
 				function = "spi0";
@@ -342,6 +471,15 @@
 			clocks = <&osc24M>;
 		};
 
+		pwm: pwm@1c21400 {
+			compatible = "allwinner,sun8i-v3s-pwm",
+				     "allwinner,sun7i-a20-pwm";
+			reg = <0x01c21400 0xc>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		lradc: lradc@1c22800 {
 			compatible = "allwinner,sun4i-a10-lradc-keys";
 			reg = <0x01c22800 0x400>;
@@ -349,6 +487,25 @@
 			status = "disabled";
 		};
 
+		codec: codec@1c22c00 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-v3s-codec";
+			reg = <0x01c22c00 0x400>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
+			clock-names = "apb", "codec";
+			resets = <&ccu RST_BUS_CODEC>;
+			dmas = <&dma 15>, <&dma 15>;
+			dma-names = "rx", "tx";
+			allwinner,codec-analog-controls = <&codec_analog>;
+			status = "disabled";
+		};
+
+		codec_analog: codec-analog@1c23000 {
+			compatible = "allwinner,sun8i-v3s-codec-analog";
+			reg = <0x01c23000 0x4>;
+		};
+
 		uart0: serial@1c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
@@ -356,6 +513,8 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART0>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
@@ -367,6 +526,8 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART1>;
+			dmas = <&dma 7>, <&dma 7>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
@@ -378,7 +539,11 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART2>;
+			dmas = <&dma 8>, <&dma 8>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART2>;
+			pinctrl-0 = <&uart2_pins>;
+			pinctrl-names = "default";
 			status = "disabled";
 		};
 
@@ -406,12 +571,57 @@
 			#size-cells = <0>;
 		};
 
+		emac: ethernet@1c30000 {
+			compatible = "allwinner,sun8i-v3s-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			phy-handle = <&int_mii_phy>;
+			phy-mode = "mii";
+			status = "disabled";
+
+			mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,dwmac-mdio";
+			};
+
+			mdio_mux: mdio-mux {
+				compatible = "allwinner,sun8i-h3-mdio-mux";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mdio-parent-bus = <&mdio>;
+				/* Only one MDIO is usable at the time */
+				internal_mdio: mdio@1 {
+					compatible = "allwinner,sun8i-h3-mdio-internal";
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					int_mii_phy: ethernet-phy@1 {
+						compatible = "ethernet-phy-ieee802.3-c22";
+						reg = <1>;
+						clocks = <&ccu CLK_BUS_EPHY>;
+						resets = <&ccu RST_BUS_EPHY>;
+					};
+				};
+			};
+		};
+
 		spi0: spi@1c68000 {
 			compatible = "allwinner,sun8i-h3-spi";
 			reg = <0x01c68000 0x1000>;
 			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 23>, <&dma 23>;
+			dma-names = "rx", "tx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&spi0_pins>;
 			resets = <&ccu RST_BUS_SPI0>;
@@ -423,12 +633,24 @@
 		gic: interrupt-controller@1c81000 {
 			compatible = "arm,gic-400";
 			reg = <0x01c81000 0x1000>,
-			      <0x01c82000 0x1000>,
+			      <0x01c82000 0x2000>,
 			      <0x01c84000 0x2000>,
 			      <0x01c86000 0x2000>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
+
+		csi1: camera@1cb4000 {
+			compatible = "allwinner,sun8i-v3s-csi";
+			reg = <0x01cb4000 0x3000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/allwinner/sun8i-v40-bananapi-m2-berry.dts
index 15c22b06fc4b..434871040aca 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v40-bananapi-m2-berry.dts
@@ -42,6 +42,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -107,6 +108,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
@@ -120,7 +125,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_dc1sw>;
 	status = "okay";
 };
@@ -198,16 +203,16 @@
 };
 
 &reg_dc1sw {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-gmac-phy";
 };
 
 &reg_dcdc1 {
 	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-3v0";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
 };
 
 &reg_dcdc2 {
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/allwinner/sun9i-a80-cubieboard4.dts
index d3b337b043a1..c8ca8cb7f5c9 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/allwinner/sun9i-a80-cubieboard4.dts
@@ -63,12 +63,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-0 {
 			label = "cubieboard4:green:usr";
 			gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */
 		};
 
-		red {
+		led-1 {
 			label = "cubieboard4:red:usr";
 			gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
 		};
@@ -87,7 +87,7 @@
 	};
 
 	vga-dac {
-		compatible = "corpro,gm7123", "adi,adv7123", "dumb-vga-dac";
+		compatible = "corpro,gm7123", "adi,adv7123";
 		vdd-supply = <&reg_dcdc1>;
 
 		ports {
@@ -129,7 +129,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_cldo1>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/allwinner/sun9i-a80-optimus.dts
index bbc6335e5631..5c3580d712e4 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/allwinner/sun9i-a80-optimus.dts
@@ -124,7 +124,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_cldo1>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/allwinner/sun9i-a80.dtsi
index 1d900f591d5f..7d3f3300f431 100644
--- a/arch/arm/boot/dts/sun9i-a80.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun9i-a80.dtsi
@@ -387,16 +387,16 @@
 		usbphy2: phy@a01800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a01800 0x4>;
-			clocks = <&usb_clocks CLK_USB1_HSIC>,
+			clocks = <&usb_clocks CLK_USB1_PHY>,
 				 <&usb_clocks CLK_USB_HSIC>,
-				 <&usb_clocks CLK_USB1_PHY>;
-			clock-names = "hsic_480M",
+				 <&usb_clocks CLK_USB1_HSIC>;
+			clock-names = "phy",
 				      "hsic_12M",
-				      "phy";
-			resets = <&usb_clocks RST_USB1_HSIC>,
-				 <&usb_clocks RST_USB1_PHY>;
-			reset-names = "hsic",
-				      "phy";
+				      "hsic_480M";
+			resets = <&usb_clocks RST_USB1_PHY>,
+				 <&usb_clocks RST_USB1_HSIC>;
+			reset-names = "phy",
+				      "hsic";
 			status = "disabled";
 			#phy-cells = <0>;
 			/* usb1 is always used with HSIC */
@@ -429,16 +429,16 @@
 		usbphy3: phy@a02800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a02800 0x4>;
-			clocks = <&usb_clocks CLK_USB2_HSIC>,
+			clocks = <&usb_clocks CLK_USB2_PHY>,
 				 <&usb_clocks CLK_USB_HSIC>,
-				 <&usb_clocks CLK_USB2_PHY>;
-			clock-names = "hsic_480M",
+				 <&usb_clocks CLK_USB2_HSIC>;
+			clock-names = "phy",
 				      "hsic_12M",
-				      "phy";
-			resets = <&usb_clocks RST_USB2_HSIC>,
-				 <&usb_clocks RST_USB2_PHY>;
-			reset-names = "hsic",
-				      "phy";
+				      "hsic_480M";
+			resets = <&usb_clocks RST_USB2_PHY>,
+				 <&usb_clocks RST_USB2_HSIC>;
+			reset-names = "phy",
+				      "hsic";
 			status = "disabled";
 			#phy-cells = <0>;
 		};
@@ -530,9 +530,7 @@
 			compatible = "allwinner,sun9i-a80-mmc-config-clk";
 			reg = <0x01c13000 0x10>;
 			clocks = <&ccu CLK_BUS_MMC>;
-			clock-names = "ahb";
 			resets = <&ccu RST_BUS_MMC>;
-			reset-names = "ahb";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			clock-output-names = "mmc0_config", "mmc1_config",
@@ -880,8 +878,12 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_LCD0>, <&ccu CLK_LCD0>;
 			clock-names = "ahb", "tcon-ch0";
-			resets = <&ccu RST_BUS_LCD0>, <&ccu RST_BUS_EDP>;
-			reset-names = "lcd", "edp";
+			resets = <&ccu RST_BUS_LCD0>,
+				 <&ccu RST_BUS_EDP>,
+				 <&ccu RST_BUS_LVDS>;
+			reset-names = "lcd",
+				      "edp",
+				      "lvds";
 			clock-output-names = "tcon0-pixel-clock";
 			#clock-cells = <0>;
 
@@ -1216,7 +1218,6 @@
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&apbs_gates 0>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apbs_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c100s-licheepi-nano.dts b/arch/arm/boot/dts/allwinner/suniv-f1c100s-licheepi-nano.dts
new file mode 100644
index 000000000000..43896723a994
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c100s-licheepi-nano.dts
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2018 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Lichee Pi Nano";
+	compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s";
+
+	aliases {
+		mmc0 = &mmc0;
+		serial0 = &uart0;
+		spi0 = &spi0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pe_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; /* PE2 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c100s.dtsi b/arch/arm/boot/dts/allwinner/suniv-f1c100s.dtsi
new file mode 100644
index 000000000000..3c61d59ab5f8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c100s.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2018 Icenowy Zheng <icenowy@aosc.io>
+ * Copyright 2018 Mesih Kilinc <mesihkilinc@gmail.com>
+ */
+
+#include <dt-bindings/clock/suniv-ccu-f1c100s.h>
+#include <dt-bindings/reset/suniv-ccu-f1c100s.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	clocks {
+		osc24M: clk-24M {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: clk-32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0x0>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		sram-controller@1c00000 {
+			compatible = "allwinner,suniv-f1c100s-system-control",
+				     "allwinner,sun4i-a10-system-control";
+			reg = <0x01c00000 0x30>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_d: sram@10000 {
+				compatible = "mmio-sram";
+				reg = <0x00010000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00010000 0x1000>;
+
+				otg_sram: sram-section@0 {
+					compatible = "allwinner,suniv-f1c100s-sram-d",
+						     "allwinner,sun4i-a10-sram-d";
+					reg = <0x0000 0x1000>;
+					status = "disabled";
+				};
+			};
+		};
+
+		spi0: spi@1c05000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c05000 0x1000>;
+			interrupts = <10>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_BUS_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@1c06000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c06000 0x1000>;
+			interrupts = <11>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_BUS_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <23>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <24>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_otg: usb@1c13000 {
+			compatible = "allwinner,suniv-f1c100s-musb";
+			reg = <0x01c13000 0x0400>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			interrupts = <26>;
+			interrupt-names = "mc";
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			extcon = <&usbphy 0>;
+			allwinner,sram = <&otg_sram 1>;
+			status = "disabled";
+		};
+
+		usbphy: phy@1c13400 {
+			compatible = "allwinner,suniv-f1c100s-usb-phy";
+			reg = <0x01c13400 0x10>;
+			reg-names = "phy_ctrl";
+			clocks = <&ccu CLK_USB_PHY0>;
+			clock-names = "usb0_phy";
+			resets = <&ccu RST_USB_PHY0>;
+			reset-names = "usb0_reset";
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ccu: clock@1c20000 {
+			compatible = "allwinner,suniv-f1c100s-ccu";
+			reg = <0x01c20000 0x400>;
+			clocks = <&osc24M>, <&osc32k>;
+			clock-names = "hosc", "losc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		intc: interrupt-controller@1c20400 {
+			compatible = "allwinner,suniv-f1c100s-ic";
+			reg = <0x01c20400 0x400>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		pio: pinctrl@1c20800 {
+			compatible = "allwinner,suniv-f1c100s-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <38>, <39>, <40>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#gpio-cells = <3>;
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+			};
+
+			/omit-if-no-ref/
+			i2c0_pd_pins: i2c0-pd-pins {
+				pins = "PD0", "PD12";
+				function = "i2c0";
+			};
+
+			spi0_pc_pins: spi0-pc-pins {
+				pins = "PC0", "PC1", "PC2", "PC3";
+				function = "spi0";
+			};
+
+			uart0_pe_pins: uart0-pe-pins {
+				pins = "PE0", "PE1";
+				function = "uart0";
+			};
+
+			/omit-if-no-ref/
+			uart1_pa_pins: uart1-pa-pins {
+				pins = "PA2", "PA3";
+				function = "uart1";
+			};
+		};
+
+		i2c0: i2c@1c27000 {
+			compatible = "allwinner,suniv-f1c100s-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c27000 0x400>;
+			interrupts = <7>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@1c27400 {
+			compatible = "allwinner,suniv-f1c100s-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c27400 0x400>;
+			interrupts = <8>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@1c27800 {
+			compatible = "allwinner,suniv-f1c100s-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c27800 0x400>;
+			interrupts = <9>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		timer@1c20c00 {
+			compatible = "allwinner,suniv-f1c100s-timer";
+			reg = <0x01c20c00 0x90>;
+			interrupts = <13>, <14>, <15>;
+			clocks = <&osc24M>;
+		};
+
+		wdt: watchdog@1c20ca0 {
+			compatible = "allwinner,suniv-f1c100s-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <16>;
+			clocks = <&osc32k>;
+		};
+
+		pwm: pwm@1c21000 {
+			compatible = "allwinner,suniv-f1c100s-pwm",
+				     "allwinner,sun7i-a20-pwm";
+			reg = <0x01c21000 0x400>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		ir: ir@1c22c00 {
+			compatible = "allwinner,suniv-f1c100s-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x01c22c00 0x400>;
+			clocks = <&ccu CLK_BUS_IR>, <&ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			resets = <&ccu RST_BUS_IR>;
+			interrupts = <6>;
+			status = "disabled";
+		};
+
+		lradc: lradc@1c23400 {
+			compatible = "allwinner,suniv-f1c100s-lradc",
+				     "allwinner,sun8i-a83t-r-lradc";
+			reg = <0x01c23400 0x400>;
+			interrupts = <22>;
+			status = "disabled";
+		};
+
+		uart0: serial@1c25000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c25000 0x400>;
+			interrupts = <1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@1c25400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c25400 0x400>;
+			interrupts = <2>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@1c25800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c25800 0x400>;
+			interrupts = <3>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c200s-lctech-pi.dts b/arch/arm/boot/dts/allwinner/suniv-f1c200s-lctech-pi.dts
new file mode 100644
index 000000000000..2d2a3f026df3
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c200s-lctech-pi.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Arm Ltd,
+ * based on work:
+ *   Copyright 2022 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Lctech Pi F1C200s";
+	compatible = "lctech,pi-f1c200s", "allwinner,suniv-f1c200s",
+		     "allwinner,suniv-f1c100s";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pa_pins>;
+	status = "okay";
+};
+
+/*
+ * This is a Type-C socket, but CC1/2 are not connected, and VBUS is connected
+ * to Vin, which supplies the board. Host mode works (if the board is powered
+ * otherwise), but peripheral is probably the intention.
+ */
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c200s-popstick-v1.1.dts b/arch/arm/boot/dts/allwinner/suniv-f1c200s-popstick-v1.1.dts
new file mode 100644
index 000000000000..184c245041a6
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c200s-popstick-v1.1.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Popcorn Computer PopStick v1.1";
+	compatible = "sourceparts,popstick-v1.1", "sourceparts,popstick",
+		     "allwinner,suniv-f1c200s", "allwinner,suniv-f1c100s";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 4 6 GPIO_ACTIVE_HIGH>; /* PE6 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	cd-gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pe_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sunxi-bananapi-m2-plus-v1.2.dtsi b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus-v1.2.dtsi
index 22466afd38a3..235994a4a2eb 100644
--- a/arch/arm/boot/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus-v1.2.dtsi
@@ -16,15 +16,27 @@
 		regulator-type = "voltage";
 		regulator-boot-on;
 		regulator-always-on;
-		regulator-min-microvolt = <1100000>;
-		regulator-max-microvolt = <1300000>;
+		regulator-min-microvolt = <1108475>;
+		regulator-max-microvolt = <1308475>;
 		regulator-ramp-delay = <50>; /* 4ms */
 		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
 		gpios-states = <0x1>;
-		states = <1100000 0>, <1300000 1>;
+		states = <1108475 0>, <1308475 1>;
 	};
 };
 
 &cpu0 {
 	cpu-supply = <&reg_vdd_cpux>;
 };
+
+&cpu1 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
diff --git a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus.dtsi
index 39263e74fbb5..1d1d127cf38f 100644
--- a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus.dtsi
@@ -77,30 +77,31 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "power";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
 	reg_gmac_3v3: gmac-3v3 {
-		      compatible = "regulator-fixed";
-		      regulator-name = "gmac-3v3";
-		      regulator-min-microvolt = <3300000>;
-		      regulator-max-microvolt = <3300000>;
-		      startup-delay-us = <100000>;
-		      enable-active-high;
-		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
 	};
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -126,7 +127,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 
 	status = "okay";
 };
@@ -219,7 +220,8 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		max-speed = <1500000>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sunxi-common-regulators.dtsi b/arch/arm/boot/dts/allwinner/sunxi-common-regulators.dtsi
index d8e5826fb3de..d8e5826fb3de 100644
--- a/arch/arm/boot/dts/sunxi-common-regulators.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-common-regulators.dtsi
diff --git a/arch/arm/boot/dts/allwinner/sunxi-d1s-t113-mangopi-mq-r.dtsi b/arch/arm/boot/dts/allwinner/sunxi-d1s-t113-mangopi-mq-r.dtsi
new file mode 100644
index 000000000000..a415c4a78a70
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sunxi-d1s-t113-mangopi-mq-r.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+/*
+ * Common peripherals and configurations for MangoPi MQ-R boards.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
+		};
+	};
+
+	/* board wide 5V supply directly from the USB-C socket */
+	reg_vcc5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board */
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	/* XC6206 LDO on the board */
+	reg_avdd2v8: regulator-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_3v3>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3v3>;
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_3v3>;
+	vcc-pd-supply = <&reg_3v3>;
+	vcc-pe-supply = <&reg_avdd2v8>;
+	vcc-pf-supply = <&reg_3v3>;
+	vcc-pg-supply = <&reg_3v3>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pb_pins>;
+	status = "okay";
+};
+
+/* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sunxi-h3-h5-emlid-neutis.dtsi b/arch/arm/boot/dts/allwinner/sunxi-h3-h5-emlid-neutis.dtsi
new file mode 100644
index 000000000000..60804b0e6c56
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sunxi-h3-h5-emlid-neutis.dtsi
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis SoMs.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii@emlid.com>
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
+		post-power-on-delay-ms = <200>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpux>;
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>;   /* PL9 */
+	status = "okay";
+};
+
+
+&de {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>;	/* PL5 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		shutdown-gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */
+		device-wakeup-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"LINEIN", "Line In",
+		"MIC1", "Mic",
+		"MIC2", "Mic",
+		"Mic",  "MBIAS";
+};
+
+&i2c0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/allwinner/sunxi-h3-h5.dtsi
index 0afea59486c2..ade1cd50e445 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -40,6 +40,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-h3-ccu.h>
 #include <dt-bindings/clock/sun8i-r-ccu.h>
@@ -114,7 +115,7 @@
 
 		display_clocks: clock@1000000 {
 			/* compatible is in per SoC .dtsi file */
-			reg = <0x01000000 0x100000>;
+			reg = <0x01000000 0x10000>;
 			clocks = <&ccu CLK_BUS_DE>,
 				 <&ccu CLK_DE>;
 			clock-names = "bus",
@@ -231,6 +232,22 @@
 		sid: eeprom@1c14000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x1c14000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ths_calibration: thermal-sensor-calibration@34 {
+				reg = <0x34 4>;
+			};
+		};
+
+		msgbox: mailbox@1c17000 {
+			compatible = "allwinner,sun8i-h3-msgbox",
+				     "allwinner,sun6i-a31-msgbox";
+			reg = <0x01c17000 0x1000>;
+			clocks = <&ccu CLK_BUS_MSGBOX>;
+			resets = <&ccu RST_BUS_MSGBOX>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <1>;
 		};
 
 		usb_otg: usb@1c19000 {
@@ -285,6 +302,8 @@
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
 			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -295,6 +314,8 @@
 			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
 				 <&ccu CLK_USB_OHCI0>;
 			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -370,7 +391,7 @@
 		ccu: clock@1c20000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -379,9 +400,11 @@
 		pio: pinctrl@1c20800 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01c20800 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -551,9 +574,16 @@
 		};
 
 		mbus: dram-controller@1c62000 {
-			compatible = "allwinner,sun8i-h3-mbus";
-			reg = <0x01c62000 0x1000>;
-			clocks = <&ccu 113>;
+			/* compatible is in per SoC .dtsi file */
+			reg = <0x01c62000 0x1000>,
+			      <0x01c63000 0x1000>;
+			reg-names = "mbus", "dram";
+			clocks = <&ccu CLK_MBUS>,
+				 <&ccu CLK_DRAM>,
+				 <&ccu CLK_BUS_DRAM>;
+			clock-names = "mbus", "dram", "bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
 			dma-ranges = <0x00000000 0x40000000 0xc0000000>;
 			#interconnect-cells = <1>;
 		};
@@ -644,6 +674,19 @@
 			status = "disabled";
 		};
 
+		i2s2: i2s@1c22800 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22800 0x400>;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>;
+			clock-names = "apb", "mod";
+			dmas = <&dma 27>;
+			resets = <&ccu RST_BUS_I2S2>;
+			dma-names = "tx";
+			status = "disabled";
+		};
+
 		codec: codec@1c22c00 {
 			#sound-dai-cells = <0>;
 			compatible = "allwinner,sun8i-h3-codec";
@@ -667,7 +710,7 @@
 			clocks = <&ccu CLK_BUS_UART0>;
 			resets = <&ccu RST_BUS_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -680,7 +723,7 @@
 			clocks = <&ccu CLK_BUS_UART1>;
 			resets = <&ccu RST_BUS_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -693,7 +736,7 @@
 			clocks = <&ccu CLK_BUS_UART2>;
 			resets = <&ccu RST_BUS_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -706,7 +749,7 @@
 			clocks = <&ccu CLK_BUS_UART3>;
 			resets = <&ccu RST_BUS_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -781,8 +824,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
@@ -811,7 +854,7 @@
 			compatible = "allwinner,sun8i-h3-hdmi-phy";
 			reg = <0x01ef0000 0x10000>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu 6>;
+				 <&ccu CLK_PLL_VIDEO>;
 			clock-names = "bus", "mod", "pll-0";
 			resets = <&ccu RST_BUS_HDMI0>;
 			reset-names = "phy";
@@ -821,6 +864,7 @@
 		rtc: rtc@1f00000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01f00000 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			clock-output-names = "osc32k", "osc32k-out", "iosc";
@@ -828,10 +872,20 @@
 			#clock-cells = <1>;
 		};
 
+		r_intc: interrupt-controller@1f00c00 {
+			compatible = "allwinner,sun8i-h3-r-intc",
+				     "allwinner,sun6i-a31-r-intc";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x01f00c00 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		r_ccu: clock@1f01400 {
 			compatible = "allwinner,sun8i-h3-r-ccu";
 			reg = <0x01f01400 0x100>;
-			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>, <&ccu 9>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
+				 <&ccu CLK_PLL_PERIPH0>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -865,11 +919,26 @@
 			#size-cells = <0>;
 		};
 
+		r_uart: serial@1f02800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01f02800 0x400>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&r_ccu CLK_APB0_UART>;
+			resets = <&r_ccu RST_APB0_UART>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_uart_pins>;
+			status = "disabled";
+		};
+
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun8i-h3-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
+			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -885,6 +954,26 @@
 				pins = "PL0", "PL1";
 				function = "s_i2c";
 			};
+
+			r_pwm_pin: r-pwm-pin {
+				pins = "PL10";
+				function = "s_pwm";
+			};
+
+			r_uart_pins: r-uart-pins {
+				pins = "PL2", "PL3";
+				function = "s_uart";
+			};
+		};
+
+		r_pwm: pwm@1f03800 {
+			compatible = "allwinner,sun8i-h3-pwm";
+			reg = <0x01f03800 0x8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_pwm_pin>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi b/arch/arm/boot/dts/allwinner/sunxi-itead-core-common.dtsi
index 0d002f83a259..0d002f83a259 100644
--- a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-itead-core-common.dtsi
diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-cc.dtsi
index 19b3b23cfaa8..89731bb34c6b 100644
--- a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-cc.dtsi
@@ -42,13 +42,14 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+			wakeup-source;
 		};
 	};
 
@@ -128,6 +129,18 @@
 	cpu-supply = <&reg_vdd_cpux>;
 };
 
+&cpu1 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-it.dtsi b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-it.dtsi
new file mode 100644
index 000000000000..50d328c2a84d
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-it.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2019 Chen-Yu Tsai <wens@csie.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+		spi0 = &spi0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status_led {
+			label = "librecomputer:blue:status";
+			gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		};
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	/* This represents the board's 5V input */
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		enable-active-high;
+	};
+
+	reg_vcc_io: vcc-io {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-io";
+		/* This is simply a MOSFET switch */
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc3v3>;
+		gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+	};
+
+	reg_vcc_usbwifi: vcc-usbwifi {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-usbwifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&pio 6 4 GPIO_ACTIVE_HIGH>; /* PG4 */
+		enable-active-high;
+	};
+
+	reg_vdd_cpux: vdd-cpux {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpux";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-active-high;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc_io>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&pio {
+	vcc-pa-supply = <&reg_vcc_io>;
+	vcc-pc-supply = <&reg_vcc_io>;
+	vcc-pd-supply = <&reg_vcc_io>;
+	vcc-pe-supply = <&reg_vcc_io>;
+	vcc-pf-supply = <&reg_vcc_io>;
+	vcc-pg-supply = <&reg_vcc_io>;
+};
+
+&r_pio {
+	vcc-pl-supply = <&reg_vcc3v3>;
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc_usbwifi>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sunxi-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sunxi-reference-design-tablet.dtsi
index 117198c52e1f..117198c52e1f 100644
--- a/arch/arm/boot/dts/sunxi-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-reference-design-tablet.dtsi
diff --git a/arch/arm/boot/dts/alphascale/Makefile b/arch/arm/boot/dts/alphascale/Makefile
new file mode 100644
index 000000000000..8d1314fc79d0
--- /dev/null
+++ b/arch/arm/boot/dts/alphascale/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_ASM9260) += \
+	alphascale-asm9260-devkit.dtb
+dtb-$(CONFIG_MACH_ASM9260) += \
+	alphascale-asm9260-devkit.dtb
diff --git a/arch/arm/boot/dts/alphascale-asm9260-devkit.dts b/arch/arm/boot/dts/alphascale/alphascale-asm9260-devkit.dts
index c77e2c902fb6..c77e2c902fb6 100644
--- a/arch/arm/boot/dts/alphascale-asm9260-devkit.dts
+++ b/arch/arm/boot/dts/alphascale/alphascale-asm9260-devkit.dts
diff --git a/arch/arm/boot/dts/alphascale-asm9260.dtsi b/arch/arm/boot/dts/alphascale/alphascale-asm9260.dtsi
index 2ce6038536fd..2ce6038536fd 100644
--- a/arch/arm/boot/dts/alphascale-asm9260.dtsi
+++ b/arch/arm/boot/dts/alphascale/alphascale-asm9260.dtsi
diff --git a/arch/arm/boot/dts/am335x-baltos-ir2110.dts b/arch/arm/boot/dts/am335x-baltos-ir2110.dts
deleted file mode 100644
index 386d5f89978e..000000000000
--- a/arch/arm/boot/dts/am335x-baltos-ir2110.dts
+++ /dev/null
@@ -1,83 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- */
-
-/*
- * VScom OnRISC
- * http://www.vscom.de
- */
-
-/dts-v1/;
-
-#include "am335x-baltos.dtsi"
-#include "am335x-baltos-leds.dtsi"
-
-/ {
-	model = "OnRISC Baltos iR 2110";
-};
-
-&am33xx_pinmux {
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE7)      /* lcd_vsync.gpio2[22] DTR */
-			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)      /* lcd_hsync.gpio2[23] DSR */
-			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)      /* lcd_pclk.gpio2[24] DCD */
-			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)      /* lcd_ac_bias_en.gpio2[25] RI */
-		>;
-	};
-
-	mmc1_pins: pinmux_mmc1_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT, MUX_MODE7)     /* MMC1 CD */
-		>;
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
-	dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
-	dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
-	dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
-	rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
-
-	status = "okay";
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&davinci_mdio {
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-};
-
-&cpsw_emac0 {
-	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
-	phy-handle = <&phy0>;
-};
-
-&cpsw_emac1 {
-	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
-	phy-handle = <&phy1>;
-};
-
-&mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-};
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
deleted file mode 100644
index d3928662aed4..000000000000
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ /dev/null
@@ -1,25 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- */
-/dts-v1/;
-
-#include "am33xx.dtsi"
-#include "am335x-bone-common.dtsi"
-#include "am335x-boneblack-common.dtsi"
-
-/ {
-	model = "TI AM335x BeagleBone Black";
-	compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
-};
-
-&cpu0_opp_table {
-	/*
-	 * All PG 2.0 silicon may not support 1GHz but some of the early
-	 * BeagleBone Blacks have PG 2.0 silicon which is guaranteed
-	 * to support 1GHz OPP so enable it for PG 2.0 on this board.
-	 */
-	oppnitro-1000000000 {
-		opp-supported-hw = <0x06 0x0100>;
-	};
-};
diff --git a/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts b/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
deleted file mode 100644
index 1e4dbc85c120..000000000000
--- a/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
+++ /dev/null
@@ -1,87 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- */
-
-/*
- * VScom OnRISC
- * http://www.vscom.de
- */
-
-/dts-v1/;
-
-#include "am335x-baltos.dtsi"
-#include "am335x-baltos-leds.dtsi"
-
-/ {
-	model = "NetCAN";
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
-
-		compatible = "gpio-leds";
-
-		led@1 {
-			label = "can_data";
-			linux,default-trigger = "netdev";
-			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-		led@2 {
-			label = "can_error";
-			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-	};
-};
-
-&am33xx_pinmux {
-	user_leds_s0: user_leds_s0 {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* CAN Data LED */
-			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* CAN Error LED */
-		>;
-	};
-
-	dcan1_pins: pinmux_dcan1_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)	/* CAN TX */
-			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)	/* CAN RX */
-		>;
-	};
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&davinci_mdio {
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-};
-
-&cpsw_emac0 {
-	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
-	phy-handle = <&phy0>;
-};
-
-&cpsw_emac1 {
-	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
-	phy-handle = <&phy1>;
-};
-
-&dcan1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&dcan1_pins>;
-
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts b/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
deleted file mode 100644
index 2298563f7334..000000000000
--- a/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
+++ /dev/null
@@ -1,115 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- */
-
-/*
- * VScom OnRISC
- * http://www.vscom.de
- */
-
-/dts-v1/;
-
-#include "am335x-baltos.dtsi"
-
-/ {
-	model = "NetCom Plus";
-};
-
-&am33xx_pinmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&dip_switches>;
-
-	dip_switches: pinmux_dip_switches {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLDOWN, MUX_MODE7)
-		>;
-	};
-
-	tca6416_pins: pinmux_tca6416_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE7)
-		>;
-	};
-
-	i2c2_pins: pinmux_i2c2_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE3)
-			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE3)
-		>;
-	};
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb1_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&usb1 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&i2c1 {
-	tca6416a: gpio@20 {
-		compatible = "ti,tca6416";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&tca6416_pins>;
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
-
-	status = "okay";
-	clock-frequency = <400000>;
-
-	tca6416b: gpio@20 {
-		compatible = "ti,tca6416";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	tca6416c: gpio@21 {
-		compatible = "ti,tca6416";
-		reg = <0x21>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-};
-
-&davinci_mdio {
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-};
-
-&cpsw_emac0 {
-	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
-	phy-handle = <&phy0>;
-};
-
-&cpsw_emac1 {
-	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
-	phy-handle = <&phy1>;
-};
diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts
deleted file mode 100644
index 4da719098028..000000000000
--- a/arch/arm/boot/dts/am335x-pocketbeagle.dts
+++ /dev/null
@@ -1,215 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Author: Robert Nelson <robertcnelson@gmail.com>
- */
-/dts-v1/;
-
-#include "am33xx.dtsi"
-#include "am335x-osd335x-common.dtsi"
-
-/ {
-	model = "TI AM335x PocketBeagle";
-	compatible = "ti,am335x-pocketbeagle", "ti,am335x-bone", "ti,am33xx";
-
-	chosen {
-		stdout-path = &uart0;
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&usr_leds_pins>;
-
-		compatible = "gpio-leds";
-
-		usr0 {
-			label = "beaglebone:green:usr0";
-			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		usr1 {
-			label = "beaglebone:green:usr1";
-			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		usr2 {
-			label = "beaglebone:green:usr2";
-			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "cpu0";
-			default-state = "off";
-		};
-
-		usr3 {
-			label = "beaglebone:green:usr3";
-			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-	};
-
-	vmmcsd_fixed: fixedregulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vmmcsd_fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-};
-
-&am33xx_pinmux {
-	i2c2_pins: pinmux-i2c2-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* (D17) uart1_rtsn.I2C2_SCL */
-			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* (D18) uart1_ctsn.I2C2_SDA */
-		>;
-	};
-
-	ehrpwm0_pins: pinmux-ehrpwm0-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* (A13) mcasp0_aclkx.ehrpwm0A */
-		>;
-	};
-
-	ehrpwm1_pins: pinmux-ehrpwm1-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* (U14) gpmc_a2.ehrpwm1A */
-		>;
-	};
-
-	mmc0_pins: pinmux-mmc0-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7)		/* (C15) spi0_cs1.gpio0[6] */
-			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_INPUT, MUX_MODE4)		/* (B12) mcasp0_aclkr.mmc0_sdwp */
-		>;
-	};
-
-	spi0_pins: pinmux-spi0-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0)
-		>;
-	};
-
-	spi1_pins: pinmux-spi1-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_INPUT_PULLUP, MUX_MODE4)	/* (C18) eCAP0_in_PWM0_out.spi1_sclk */
-			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE4)	/* (E18) uart0_ctsn.spi1_d0 */
-			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE4)	/* (E17) uart0_rtsn.spi1_d1 */
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE4)	/* (A15) xdma_event_intr0.spi1_cs1 */
-		>;
-	};
-
-	usr_leds_pins: pinmux-usr-leds-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7)		/* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT, MUX_MODE7)		/* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_OUTPUT, MUX_MODE7)		/* (T15) gpmc_a7.gpio1[23] - USR_LED_2 */
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_OUTPUT, MUX_MODE7)		/* (V16) gpmc_a8.gpio1[24] - USR_LED_3 */
-		>;
-	};
-
-	uart0_pins: pinmux-uart0-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-		>;
-	};
-
-	uart4_pins: pinmux-uart4-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)	/* (T17) gpmc_wait0.uart4_rxd */
-			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* (U17) gpmc_wpn.uart4_txd */
-		>;
-	};
-};
-
-&epwmss0 {
-	status = "okay";
-};
-
-&ehrpwm0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&ehrpwm0_pins>;
-};
-
-&epwmss1 {
-	status = "okay";
-};
-
-&ehrpwm1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&ehrpwm1_pins>;
-};
-
-&i2c0 {
-	eeprom: eeprom@50 {
-		compatible = "atmel,24c256";
-		reg = <0x50>;
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
-
-	status = "okay";
-	clock-frequency = <400000>;
-};
-
-&mmc1 {
-	status = "okay";
-	vmmc-supply = <&vmmcsd_fixed>;
-	bus-width = <4>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
-	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
-};
-
-&rtc {
-	system-power-controller;
-};
-
-&tscadc {
-	status = "okay";
-	adc {
-		ti,adc-channels = <0 1 2 3 4 5 6 7>;
-		ti,chan-step-avg = <16 16 16 16 16 16 16 16>;
-		ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>;
-		ti,chan-step-sampledelay = <0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0>;
-	};
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins>;
-
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins>;
-
-	status = "okay";
-};
-
-&usb0 {
-	dr_mode = "otg";
-};
-
-&usb1 {
-	dr_mode = "host";
-};
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
deleted file mode 100644
index 646f11430dad..000000000000
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ /dev/null
@@ -1,490 +0,0 @@
-/*
- * Device Tree Source for AM33XX SoC
- *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <dt-bindings/bus/ti-sysc.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/am33xx.h>
-#include <dt-bindings/clock/am3.h>
-
-/ {
-	compatible = "ti,am33xx";
-	interrupt-parent = <&intc>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-	chosen { };
-
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
-		serial5 = &uart5;
-		d-can0 = &dcan0;
-		d-can1 = &dcan1;
-		usb0 = &usb0;
-		usb1 = &usb1;
-		phy0 = &usb0_phy;
-		phy1 = &usb1_phy;
-		ethernet0 = &cpsw_emac0;
-		ethernet1 = &cpsw_emac1;
-		spi0 = &spi0;
-		spi1 = &spi1;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		cpu@0 {
-			compatible = "arm,cortex-a8";
-			device_type = "cpu";
-			reg = <0>;
-
-			operating-points-v2 = <&cpu0_opp_table>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-		};
-	};
-
-	cpu0_opp_table: opp-table {
-		compatible = "operating-points-v2-ti-cpu";
-		syscon = <&scm_conf>;
-
-		/*
-		 * The three following nodes are marked with opp-suspend
-		 * because the can not be enabled simultaneously on a
-		 * single SoC.
-		 */
-		opp50-300000000 {
-			opp-hz = /bits/ 64 <300000000>;
-			opp-microvolt = <950000 931000 969000>;
-			opp-supported-hw = <0x06 0x0010>;
-			opp-suspend;
-		};
-
-		opp100-275000000 {
-			opp-hz = /bits/ 64 <275000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x01 0x00FF>;
-			opp-suspend;
-		};
-
-		opp100-300000000 {
-			opp-hz = /bits/ 64 <300000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x06 0x0020>;
-			opp-suspend;
-		};
-
-		opp100-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x01 0xFFFF>;
-		};
-
-		opp100-600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x06 0x0040>;
-		};
-
-		opp120-600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <1200000 1176000 1224000>;
-			opp-supported-hw = <0x01 0xFFFF>;
-		};
-
-		opp120-720000000 {
-			opp-hz = /bits/ 64 <720000000>;
-			opp-microvolt = <1200000 1176000 1224000>;
-			opp-supported-hw = <0x06 0x0080>;
-		};
-
-		oppturbo-720000000 {
-			opp-hz = /bits/ 64 <720000000>;
-			opp-microvolt = <1260000 1234800 1285200>;
-			opp-supported-hw = <0x01 0xFFFF>;
-		};
-
-		oppturbo-800000000 {
-			opp-hz = /bits/ 64 <800000000>;
-			opp-microvolt = <1260000 1234800 1285200>;
-			opp-supported-hw = <0x06 0x0100>;
-		};
-
-		oppnitro-1000000000 {
-			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <1325000 1298500 1351500>;
-			opp-supported-hw = <0x04 0x0200>;
-		};
-	};
-
-	pmu@4b000000 {
-		compatible = "arm,cortex-a8-pmu";
-		interrupts = <3>;
-		reg = <0x4b000000 0x1000000>;
-		ti,hwmods = "debugss";
-	};
-
-	/*
-	 * The soc node represents the soc top level view. It is used for IPs
-	 * that are not memory mapped in the MPU view or for the MPU itself.
-	 */
-	soc {
-		compatible = "ti,omap-infra";
-		mpu {
-			compatible = "ti,omap3-mpu";
-			ti,hwmods = "mpu";
-			pm-sram = <&pm_sram_code
-				   &pm_sram_data>;
-		};
-	};
-
-	/*
-	 * XXX: Use a flat representation of the AM33XX interconnect.
-	 * The real AM33XX interconnect network is quite complex. Since
-	 * it will not bring real advantage to represent that in DT
-	 * for the moment, just use a fake OCP bus entry to represent
-	 * the whole bus hierarchy.
-	 */
-	ocp {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		ti,hwmods = "l3_main";
-
-		l4_wkup: interconnect@44c00000 {
-			wkup_m3: wkup_m3@100000 {
-				compatible = "ti,am3352-wkup-m3";
-				reg = <0x100000 0x4000>,
-				      <0x180000 0x2000>;
-				reg-names = "umem", "dmem";
-				ti,hwmods = "wkup_m3";
-				ti,pm-firmware = "am335x-pm-firmware.elf";
-			};
-		};
-		l4_per: interconnect@48000000 {
-		};
-		l4_fw: interconnect@47c00000 {
-		};
-		l4_fast: interconnect@4a000000 {
-		};
-		l4_mpuss: interconnect@4b140000 {
-		};
-
-		intc: interrupt-controller@48200000 {
-			compatible = "ti,am33xx-intc";
-			interrupt-controller;
-			#interrupt-cells = <1>;
-			reg = <0x48200000 0x1000>;
-		};
-
-		edma: edma@49000000 {
-			compatible = "ti,edma3-tpcc";
-			ti,hwmods = "tpcc";
-			reg =	<0x49000000 0x10000>;
-			reg-names = "edma3_cc";
-			interrupts = <12 13 14>;
-			interrupt-names = "edma3_ccint", "edma3_mperr",
-					  "edma3_ccerrint";
-			dma-requests = <64>;
-			#dma-cells = <2>;
-
-			ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
-				   <&edma_tptc2 0>;
-
-			ti,edma-memcpy-channels = <20 21>;
-		};
-
-		edma_tptc0: tptc@49800000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc0";
-			reg =	<0x49800000 0x100000>;
-			interrupts = <112>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		edma_tptc1: tptc@49900000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc1";
-			reg =	<0x49900000 0x100000>;
-			interrupts = <113>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		edma_tptc2: tptc@49a00000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc2";
-			reg =	<0x49a00000 0x100000>;
-			interrupts = <114>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		target-module@47810000 {
-			compatible = "ti,sysc-omap2", "ti,sysc";
-			reg = <0x478102fc 0x4>,
-			      <0x47810110 0x4>,
-			      <0x47810114 0x4>;
-			reg-names = "rev", "sysc", "syss";
-			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
-					 SYSC_OMAP2_ENAWAKEUP |
-					 SYSC_OMAP2_SOFTRESET |
-					 SYSC_OMAP2_AUTOIDLE)>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
-			ti,syss-mask = <1>;
-			clocks = <&l3s_clkctrl AM3_L3S_MMC3_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0x47810000 0x1000>;
-
-			mmc3: mmc@0 {
-				compatible = "ti,omap4-hsmmc";
-				ti,needs-special-reset;
-				interrupts = <29>;
-				reg = <0x0 0x1000>;
-			};
-		};
-
-		usb: target-module@47400000 {
-			compatible = "ti,sysc-omap4", "ti,sysc";
-			reg = <0x47400000 0x4>,
-			      <0x47400010 0x4>;
-			reg-names = "rev", "sysc";
-			ti,sysc-mask = <(SYSC_OMAP4_FREEEMU |
-					 SYSC_OMAP2_SOFTRESET)>;
-			ti,sysc-midle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			clocks = <&l3s_clkctrl AM3_L3S_USB_OTG_HS_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0x47400000 0x5000>;
-
-			usb0_phy: usb-phy@1300 {
-				compatible = "ti,am335x-usb-phy";
-				reg = <0x1300 0x100>;
-				reg-names = "phy";
-				ti,ctrl_mod = <&usb_ctrl_mod>;
-				#phy-cells = <0>;
-			};
-
-			usb0: usb@1400 {
-				compatible = "ti,musb-am33xx";
-				reg = <0x1400 0x400>,
-				      <0x1000 0x200>;
-				reg-names = "mc", "control";
-
-				interrupts = <18>;
-				interrupt-names = "mc";
-				dr_mode = "otg";
-				mentor,multipoint = <1>;
-				mentor,num-eps = <16>;
-				mentor,ram-bits = <12>;
-				mentor,power = <500>;
-				phys = <&usb0_phy>;
-
-				dmas = <&cppi41dma  0 0 &cppi41dma  1 0
-					&cppi41dma  2 0 &cppi41dma  3 0
-					&cppi41dma  4 0 &cppi41dma  5 0
-					&cppi41dma  6 0 &cppi41dma  7 0
-					&cppi41dma  8 0 &cppi41dma  9 0
-					&cppi41dma 10 0 &cppi41dma 11 0
-					&cppi41dma 12 0 &cppi41dma 13 0
-					&cppi41dma 14 0 &cppi41dma  0 1
-					&cppi41dma  1 1 &cppi41dma  2 1
-					&cppi41dma  3 1 &cppi41dma  4 1
-					&cppi41dma  5 1 &cppi41dma  6 1
-					&cppi41dma  7 1 &cppi41dma  8 1
-					&cppi41dma  9 1 &cppi41dma 10 1
-					&cppi41dma 11 1 &cppi41dma 12 1
-					&cppi41dma 13 1 &cppi41dma 14 1>;
-				dma-names =
-					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
-					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
-					"rx14", "rx15",
-					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
-					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
-					"tx14", "tx15";
-			};
-
-			usb1_phy: usb-phy@1b00 {
-				compatible = "ti,am335x-usb-phy";
-				reg = <0x1b00 0x100>;
-				reg-names = "phy";
-				ti,ctrl_mod = <&usb_ctrl_mod>;
-				#phy-cells = <0>;
-			};
-
-			usb1: usb@1800 {
-				compatible = "ti,musb-am33xx";
-				reg = <0x1c00 0x400>,
-				      <0x1800 0x200>;
-				reg-names = "mc", "control";
-				interrupts = <19>;
-				interrupt-names = "mc";
-				dr_mode = "otg";
-				mentor,multipoint = <1>;
-				mentor,num-eps = <16>;
-				mentor,ram-bits = <12>;
-				mentor,power = <500>;
-				phys = <&usb1_phy>;
-
-				dmas = <&cppi41dma 15 0 &cppi41dma 16 0
-					&cppi41dma 17 0 &cppi41dma 18 0
-					&cppi41dma 19 0 &cppi41dma 20 0
-					&cppi41dma 21 0 &cppi41dma 22 0
-					&cppi41dma 23 0 &cppi41dma 24 0
-					&cppi41dma 25 0 &cppi41dma 26 0
-					&cppi41dma 27 0 &cppi41dma 28 0
-					&cppi41dma 29 0 &cppi41dma 15 1
-					&cppi41dma 16 1 &cppi41dma 17 1
-					&cppi41dma 18 1 &cppi41dma 19 1
-					&cppi41dma 20 1 &cppi41dma 21 1
-					&cppi41dma 22 1 &cppi41dma 23 1
-					&cppi41dma 24 1 &cppi41dma 25 1
-					&cppi41dma 26 1 &cppi41dma 27 1
-					&cppi41dma 28 1 &cppi41dma 29 1>;
-				dma-names =
-					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
-					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
-					"rx14", "rx15",
-					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
-					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
-					"tx14", "tx15";
-			};
-
-			cppi41dma: dma-controller@2000 {
-				compatible = "ti,am3359-cppi41";
-				reg =  <0x0000 0x1000>,
-				       <0x2000 0x1000>,
-				       <0x3000 0x1000>,
-				       <0x4000 0x4000>;
-				reg-names = "glue", "controller", "scheduler", "queuemgr";
-				interrupts = <17>;
-				interrupt-names = "glue";
-				#dma-cells = <2>;
-				#dma-channels = <30>;
-				#dma-requests = <256>;
-			};
-		};
-
-		ocmcram: sram@40300000 {
-			compatible = "mmio-sram";
-			reg = <0x40300000 0x10000>; /* 64k */
-			ranges = <0x0 0x40300000 0x10000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			pm_sram_code: pm-code-sram@0 {
-				compatible = "ti,sram";
-				reg = <0x0 0x1000>;
-				protect-exec;
-			};
-
-			pm_sram_data: pm-data-sram@1000 {
-				compatible = "ti,sram";
-				reg = <0x1000 0x1000>;
-				pool;
-			};
-		};
-
-		emif: emif@4c000000 {
-			compatible = "ti,emif-am3352";
-			reg = <0x4c000000 0x1000000>;
-			ti,hwmods = "emif";
-			interrupts = <101>;
-			sram = <&pm_sram_code
-				&pm_sram_data>;
-			ti,no-idle;
-		};
-
-		gpmc: gpmc@50000000 {
-			compatible = "ti,am3352-gpmc";
-			ti,hwmods = "gpmc";
-			ti,no-idle-on-init;
-			reg = <0x50000000 0x2000>;
-			interrupts = <100>;
-			dmas = <&edma 52 0>;
-			dma-names = "rxtx";
-			gpmc,num-cs = <7>;
-			gpmc,num-waitpins = <2>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			status = "disabled";
-		};
-
-		sham: sham@53100000 {
-			compatible = "ti,omap4-sham";
-			ti,hwmods = "sham";
-			reg = <0x53100000 0x200>;
-			interrupts = <109>;
-			dmas = <&edma 36 0>;
-			dma-names = "rx";
-		};
-
-		aes: aes@53500000 {
-			compatible = "ti,omap4-aes";
-			ti,hwmods = "aes";
-			reg = <0x53500000 0xa0>;
-			interrupts = <103>;
-			dmas = <&edma 6 0>,
-			       <&edma 5 0>;
-			dma-names = "tx", "rx";
-		};
-	};
-};
-
-#include "am33xx-l4.dtsi"
-#include "am33xx-clocks.dtsi"
-
-&prcm {
-	prm_per: prm@c00 {
-		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
-		reg = <0xc00 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_wkup: prm@d00 {
-		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
-		reg = <0xd00 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_device: prm@f00 {
-		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
-		reg = <0xf00 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_gfx: prm@1100 {
-		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1100 0x100>;
-		#reset-cells = <1>;
-	};
-};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
deleted file mode 100644
index ca0aa3f26c0a..000000000000
--- a/arch/arm/boot/dts/am4372.dtsi
+++ /dev/null
@@ -1,402 +0,0 @@
-/*
- * Device Tree Source for AM4372 SoC
- *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <dt-bindings/bus/ti-sysc.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/am4.h>
-
-/ {
-	compatible = "ti,am4372", "ti,am43";
-	interrupt-parent = <&wakeupgen>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-	chosen { };
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0 0>;
-	};
-
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
-		serial5 = &uart5;
-		ethernet0 = &cpsw_emac0;
-		ethernet1 = &cpsw_emac1;
-		spi0 = &qspi;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		cpu: cpu@0 {
-			compatible = "arm,cortex-a9";
-			device_type = "cpu";
-			reg = <0>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			operating-points-v2 = <&cpu0_opp_table>;
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-		};
-	};
-
-	cpu0_opp_table: opp-table {
-		compatible = "operating-points-v2-ti-cpu";
-		syscon = <&scm_conf>;
-
-		opp50-300000000 {
-			opp-hz = /bits/ 64 <300000000>;
-			opp-microvolt = <950000 931000 969000>;
-			opp-supported-hw = <0xFF 0x01>;
-			opp-suspend;
-		};
-
-		opp100-600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0xFF 0x04>;
-		};
-
-		opp120-720000000 {
-			opp-hz = /bits/ 64 <720000000>;
-			opp-microvolt = <1200000 1176000 1224000>;
-			opp-supported-hw = <0xFF 0x08>;
-		};
-
-		oppturbo-800000000 {
-			opp-hz = /bits/ 64 <800000000>;
-			opp-microvolt = <1260000 1234800 1285200>;
-			opp-supported-hw = <0xFF 0x10>;
-		};
-
-		oppnitro-1000000000 {
-			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <1325000 1298500 1351500>;
-			opp-supported-hw = <0xFF 0x20>;
-		};
-	};
-
-	soc {
-		compatible = "ti,omap-infra";
-		mpu {
-			compatible = "ti,omap4-mpu";
-			ti,hwmods = "mpu";
-			pm-sram = <&pm_sram_code
-				   &pm_sram_data>;
-		};
-	};
-
-	gic: interrupt-controller@48241000 {
-		compatible = "arm,cortex-a9-gic";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0x48241000 0x1000>,
-		      <0x48240100 0x0100>;
-		interrupt-parent = <&gic>;
-	};
-
-	wakeupgen: interrupt-controller@48281000 {
-		compatible = "ti,omap4-wugen-mpu";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0x48281000 0x1000>;
-		interrupt-parent = <&gic>;
-	};
-
-	scu: scu@48240000 {
-		compatible = "arm,cortex-a9-scu";
-		reg = <0x48240000 0x100>;
-	};
-
-	global_timer: timer@48240200 {
-		compatible = "arm,cortex-a9-global-timer";
-		reg = <0x48240200 0x100>;
-		interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
-		interrupt-parent = <&gic>;
-		clocks = <&mpu_periphclk>;
-	};
-
-	local_timer: timer@48240600 {
-		compatible = "arm,cortex-a9-twd-timer";
-		reg = <0x48240600 0x100>;
-		interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>;
-		interrupt-parent = <&gic>;
-		clocks = <&mpu_periphclk>;
-	};
-
-	l2-cache-controller@48242000 {
-		compatible = "arm,pl310-cache";
-		reg = <0x48242000 0x1000>;
-		cache-unified;
-		cache-level = <2>;
-	};
-
-	ocp@44000000 {
-		compatible = "ti,am4372-l3-noc", "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		ti,hwmods = "l3_main";
-		ti,no-idle;
-		reg = <0x44000000 0x400000
-		       0x44800000 0x400000>;
-		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-
-		l4_wkup: interconnect@44c00000 {
-			wkup_m3: wkup_m3@100000 {
-				compatible = "ti,am4372-wkup-m3";
-				reg = <0x100000 0x4000>,
-				      <0x180000	0x2000>;
-				reg-names = "umem", "dmem";
-				ti,hwmods = "wkup_m3";
-				ti,pm-firmware = "am335x-pm-firmware.elf";
-			};
-		};
-		l4_per: interconnect@48000000 {
-		};
-		l4_fast: interconnect@4a000000 {
-		};
-
-		emif: emif@4c000000 {
-			compatible = "ti,emif-am4372";
-			reg = <0x4c000000 0x1000000>;
-			ti,hwmods = "emif";
-			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			ti,no-idle;
-			sram = <&pm_sram_code
-				&pm_sram_data>;
-		};
-
-		edma: edma@49000000 {
-			compatible = "ti,edma3-tpcc";
-			ti,hwmods = "tpcc";
-			reg =	<0x49000000 0x10000>;
-			reg-names = "edma3_cc";
-			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_ccint", "edma3_mperr",
-					  "edma3_ccerrint";
-			dma-requests = <64>;
-			#dma-cells = <2>;
-
-			ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
-				   <&edma_tptc2 0>;
-
-			ti,edma-memcpy-channels = <58 59>;
-		};
-
-		edma_tptc0: tptc@49800000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc0";
-			reg =	<0x49800000 0x100000>;
-			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		edma_tptc1: tptc@49900000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc1";
-			reg =	<0x49900000 0x100000>;
-			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		edma_tptc2: tptc@49a00000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc2";
-			reg =	<0x49a00000 0x100000>;
-			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		target-module@47810000 {
-			compatible = "ti,sysc-omap2", "ti,sysc";
-			reg = <0x478102fc 0x4>,
-			      <0x47810110 0x4>,
-			      <0x47810114 0x4>;
-			reg-names = "rev", "sysc", "syss";
-			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
-					 SYSC_OMAP2_ENAWAKEUP |
-					 SYSC_OMAP2_SOFTRESET |
-					 SYSC_OMAP2_AUTOIDLE)>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
-			ti,syss-mask = <1>;
-			clocks = <&l3s_clkctrl AM4_L3S_MMC3_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0x47810000 0x1000>;
-
-			mmc3: mmc@0 {
-				compatible = "ti,omap4-hsmmc";
-				ti,needs-special-reset;
-				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x1000>;
-			};
-		};
-
-		sham: sham@53100000 {
-			compatible = "ti,omap5-sham";
-			ti,hwmods = "sham";
-			reg = <0x53100000 0x300>;
-			dmas = <&edma 36 0>;
-			dma-names = "rx";
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		aes: aes@53501000 {
-			compatible = "ti,omap4-aes";
-			ti,hwmods = "aes";
-			reg = <0x53501000 0xa0>;
-			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&edma 6 0>,
-				<&edma 5 0>;
-			dma-names = "tx", "rx";
-		};
-
-		des: des@53701000 {
-			compatible = "ti,omap4-des";
-			ti,hwmods = "des";
-			reg = <0x53701000 0xa0>;
-			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&edma 34 0>,
-				<&edma 33 0>;
-			dma-names = "tx", "rx";
-		};
-
-		gpmc: gpmc@50000000 {
-			compatible = "ti,am3352-gpmc";
-			ti,hwmods = "gpmc";
-			dmas = <&edma 52 0>;
-			dma-names = "rxtx";
-			clocks = <&l3s_gclk>;
-			clock-names = "fck";
-			reg = <0x50000000 0x2000>;
-			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-			gpmc,num-cs = <7>;
-			gpmc,num-waitpins = <2>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			status = "disabled";
-		};
-
-		qspi: spi@47900000 {
-			compatible = "ti,am4372-qspi";
-			reg = <0x47900000 0x100>,
-			      <0x30000000 0x4000000>;
-			reg-names = "qspi_base", "qspi_mmap";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			ti,hwmods = "qspi";
-			interrupts = <0 138 0x4>;
-			num-cs = <4>;
-			status = "disabled";
-		};
-
-		dss: dss@4832a000 {
-			compatible = "ti,omap3-dss";
-			reg = <0x4832a000 0x200>;
-			status = "disabled";
-			ti,hwmods = "dss_core";
-			clocks = <&disp_clk>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			dispc: dispc@4832a400 {
-				compatible = "ti,omap3-dispc";
-				reg = <0x4832a400 0x400>;
-				interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
-				ti,hwmods = "dss_dispc";
-				clocks = <&disp_clk>;
-				clock-names = "fck";
-
-				max-memory-bandwidth = <230000000>;
-			};
-
-			rfbi: rfbi@4832a800 {
-				compatible = "ti,omap3-rfbi";
-				reg = <0x4832a800 0x100>;
-				ti,hwmods = "dss_rfbi";
-				clocks = <&disp_clk>;
-				clock-names = "fck";
-				status = "disabled";
-			};
-		};
-
-		ocmcram: sram@40300000 {
-			compatible = "mmio-sram";
-			reg = <0x40300000 0x40000>; /* 256k */
-			ranges = <0x0 0x40300000 0x40000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			pm_sram_code: pm-code-sram@0 {
-				compatible = "ti,sram";
-				reg = <0x0 0x1000>;
-				protect-exec;
-			};
-
-			pm_sram_data: pm-data-sram@1000 {
-				compatible = "ti,sram";
-				reg = <0x1000 0x1000>;
-				pool;
-			};
-		};
-	};
-};
-
-#include "am437x-l4.dtsi"
-#include "am43xx-clocks.dtsi"
-
-&prcm {
-	prm_gfx: prm@400 {
-		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x400 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_per: prm@800 {
-		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x800 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_wkup: prm@2000 {
-		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x2000 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_device: prm@4000 {
-		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x4000 0x100>;
-		#reset-cells = <1>;
-	};
-};
diff --git a/arch/arm/boot/dts/amazon/Makefile b/arch/arm/boot/dts/amazon/Makefile
new file mode 100644
index 000000000000..58af5c4846ef
--- /dev/null
+++ b/arch/arm/boot/dts/amazon/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ALPINE) += \
+	alpine-db.dtb
+dtb-$(CONFIG_ARCH_ALPINE) += \
+	alpine-db.dtb
diff --git a/arch/arm/boot/dts/alpine-db.dts b/arch/arm/boot/dts/amazon/alpine-db.dts
index dfb5a0802273..dfb5a0802273 100644
--- a/arch/arm/boot/dts/alpine-db.dts
+++ b/arch/arm/boot/dts/amazon/alpine-db.dts
diff --git a/arch/arm/boot/dts/alpine.dtsi b/arch/arm/boot/dts/amazon/alpine.dtsi
index d3036ea823d1..ff68dfb4eb78 100644
--- a/arch/arm/boot/dts/alpine.dtsi
+++ b/arch/arm/boot/dts/amazon/alpine.dtsi
@@ -91,7 +91,7 @@
 		};
 
 		/* Interrupt Controller */
-		gic: gic@fb001000 {
+		gic: interrupt-controller@fb001000 {
 			compatible = "arm,cortex-a15-gic";
 			#interrupt-cells = <3>;
 			#size-cells = <0>;
@@ -126,7 +126,7 @@
 				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		uart0: uart@fd883000 {
+		uart0: serial@fd883000 {
 			compatible = "ns16550a";
 			reg = <0x0 0xfd883000 0x0 0x1000>;
 			clock-frequency = <375000000>;
@@ -135,7 +135,7 @@
 			reg-io-width = <4>;
 		};
 
-		uart1: uart@fd884000 {
+		uart1: serial@fd884000 {
 			compatible = "ns16550a";
 			reg = <0x0 0xfd884000 0x0 0x1000>;
 			clock-frequency = <375000000>;
@@ -154,7 +154,7 @@
 			reg = <0x0 0xfbc00000 0x0 0x100000>;
 			interrupt-map-mask = <0xf800 0 0 7>;
 			/* Add legacy interrupts for SATA devices only */
-			interrupt-map =	<0x4000 0 0 1 &gic 0 43 4>,
+			interrupt-map = <0x4000 0 0 1 &gic 0 43 4>,
 					<0x4800 0 0 1 &gic 0 44 4>;
 
 			/* 32 bit non prefetchable memory space */
diff --git a/arch/arm/boot/dts/amlogic/Makefile b/arch/arm/boot/dts/amlogic/Makefile
new file mode 100644
index 000000000000..a84310780ea3
--- /dev/null
+++ b/arch/arm/boot/dts/amlogic/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_MESON6) += \
+	meson6-atv1200.dtb
+dtb-$(CONFIG_MACH_MESON8) += \
+	meson8-minix-neo-x8.dtb \
+	meson8b-ec100.dtb \
+	meson8b-mxq.dtb \
+	meson8b-odroidc1.dtb \
+	meson8m2-mxiii-plus.dtb
diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/amlogic/meson.dtsi
index c4447f6c8b2c..8e3860d5d916 100644
--- a/arch/arm/boot/dts/meson.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson.dtsi
@@ -5,17 +5,16 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/sound/meson-aiu.h>
 
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 	interrupt-parent = <&gic>;
 
-	L2: l2-cache-controller@c4200000 {
-		compatible = "arm,pl310-cache";
-		reg = <0xc4200000 0x1000>;
-		cache-unified;
-		cache-level = <2>;
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&saradc 8>;
 	};
 
 	soc {
@@ -38,6 +37,17 @@
 				reg = <0x4000 0x400>;
 			};
 
+			aiu: audio-controller@5400 {
+				compatible = "amlogic,aiu";
+				#sound-dai-cells = <2>;
+				sound-name-prefix = "AIU";
+				reg = <0x5400 0x2ac>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>,
+					     <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+				interrupt-names = "i2s", "spdif";
+				status = "disabled";
+			};
+
 			assist: assist@7c00 {
 				compatible = "amlogic,meson-mx-assist", "syscon";
 				reg = <0x7c00 0x200>;
@@ -49,14 +59,15 @@
 			};
 
 			uart_A: serial@84c0 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x84c0 0x18>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+				fifo-size = <128>;
 				status = "disabled";
 			};
 
 			uart_B: serial@84dc {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x84dc 0x18>;
 				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -94,7 +105,7 @@
 			};
 
 			uart_C: serial@8700 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x8700 0x18>;
 				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -140,6 +151,13 @@
 				status = "disabled";
 			};
 
+			sdhc: mmc@8e00 {
+				compatible = "amlogic,meson-mx-sdhc";
+				reg = <0x8e00 0x42>;
+				interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
+
 			gpio_intc: interrupt-controller@9880 {
 				compatible = "amlogic,meson-gpio-intc";
 				reg = <0x9880 0x10>;
@@ -165,6 +183,13 @@
 			};
 		};
 
+		L2: cache-controller@c4200000 {
+			compatible = "arm,pl310-cache";
+			reg = <0xc4200000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
 		periph: bus@c4300000 {
 			compatible = "simple-bus";
 			reg = <0xc4300000 0x10000>;
@@ -188,15 +213,22 @@
 			#size-cells = <1>;
 			ranges = <0x0 0xc8100000 0x100000>;
 
+			ao_arc_rproc: remoteproc@1c {
+				compatible = "amlogic,meson-mx-ao-arc";
+				reg = <0x1c 0x8>, <0x38 0x8>;
+				reg-names = "remap", "cpu";
+				status = "disabled";
+			};
+
 			ir_receiver: ir-receiver@480 {
-				compatible= "amlogic,meson6-ir";
+				compatible = "amlogic,meson6-ir";
 				reg = <0x480 0x20>;
 				interrupts = <GIC_SPI 15 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			uart_AO: serial@4c0 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart", "amlogic,meson-ao-uart";
 				reg = <0x4c0 0x18>;
 				interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -229,6 +261,9 @@
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usb0_phy>;
 			phy-names = "usb2-phy";
+			g-rx-fifo-size = <512>;
+			g-np-tx-fifo-size = <500>;
+			g-tx-fifo-size = <256 192 128 128 128>;
 			dr_mode = "host";
 			status = "disabled";
 		};
@@ -282,4 +317,18 @@
 			};
 		};
 	};
+
+	thermal_sensor: thermal-sensor {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&saradc 8>;
+		io-channel-names = "sensor-channel";
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
 }; /* end of / */
diff --git a/arch/arm/boot/dts/meson6-atv1200.dts b/arch/arm/boot/dts/amlogic/meson6-atv1200.dts
index 98e1c94c0261..98e1c94c0261 100644
--- a/arch/arm/boot/dts/meson6-atv1200.dts
+++ b/arch/arm/boot/dts/amlogic/meson6-atv1200.dts
diff --git a/arch/arm/boot/dts/meson6.dtsi b/arch/arm/boot/dts/amlogic/meson6.dtsi
index 2d31b7ce3f8c..4716030a48d0 100644
--- a/arch/arm/boot/dts/meson6.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson6.dtsi
@@ -36,13 +36,6 @@
 		ranges = <0x0 0xd0000000 0x40000>;
 	};
 
-	xtal: xtal-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <24000000>;
-		clock-output-names = "xtal";
-		#clock-cells = <0>;
-	};
-
 	clk81: clk@0 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
diff --git a/arch/arm/boot/dts/meson8-minix-neo-x8.dts b/arch/arm/boot/dts/amlogic/meson8-minix-neo-x8.dts
index 61ec929ab86e..c6d1c5a8a3bf 100644
--- a/arch/arm/boot/dts/meson8-minix-neo-x8.dts
+++ b/arch/arm/boot/dts/amlogic/meson8-minix-neo-x8.dts
@@ -27,7 +27,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-blue {
 			label = "x8:blue:power";
 			gpios = <&gpio_ao GPIO_TEST_N GPIO_ACTIVE_HIGH>;
 		};
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&spi_nor_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25l1606e";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/amlogic/meson8.dtsi
index 5a7e3e5caebe..59932fbfd5d5 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8.dtsi
@@ -3,10 +3,13 @@
  * Copyright 2014 Carlo Caione <carlo@caione.org>
  */
 
+#include <dt-bindings/clock/meson8-ddr-clkc.h>
 #include <dt-bindings/clock/meson8b-clkc.h>
 #include <dt-bindings/gpio/meson8-gpio.h>
+#include <dt-bindings/power/meson8-power.h>
 #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h>
 #include <dt-bindings/reset/amlogic,meson8b-reset.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "meson.dtsi"
 
 / {
@@ -26,6 +29,7 @@
 			resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu1: cpu@201 {
@@ -37,6 +41,7 @@
 			resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu2: cpu@202 {
@@ -48,6 +53,7 @@
 			resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu3: cpu@203 {
@@ -59,6 +65,7 @@
 			resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 	};
 
@@ -126,11 +133,11 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
-		opp-182150000 {
-			opp-hz = /bits/ 64 <182150000>;
+		opp-182142857 {
+			opp-hz = /bits/ 64 <182142857>;
 			opp-microvolt = <1150000>;
 		};
 		opp-318750000 {
@@ -188,6 +195,54 @@
 		};
 	};
 
+	thermal-zones {
+		soc {
+			polling-delay-passive = <250>; /* milliseconds */
+			polling-delay = <1000>; /* milliseconds */
+			thermal-sensors = <&thermal_sensor>;
+
+			cooling-maps {
+				map0 {
+					trip = <&soc_passive>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&soc_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				soc_passive: soc-passive {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				soc_hot: soc-hot {
+					temperature = <90000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				soc_critical: soc-critical {
+					temperature = <110000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	mmcbus: bus@c8000000 {
 		compatible = "simple-bus";
 		reg = <0xc8000000 0x8000>;
@@ -195,6 +250,14 @@
 		#size-cells = <1>;
 		ranges = <0x0 0xc8000000 0x8000>;
 
+		ddr_clkc: clock-controller@400 {
+			compatible = "amlogic,meson8-ddr-clkc";
+			reg = <0x400 0x20>;
+			clocks = <&xtal>;
+			clock-names = "xtal";
+			#clock-cells = <1>;
+		};
+
 		dmcbus: bus@6000 {
 			compatible = "simple-bus";
 			reg = <0x6000 0x400>;
@@ -230,8 +293,6 @@
 				     <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
@@ -243,17 +304,46 @@
 					  "pp2", "ppmmu2", "pp4", "ppmmu4",
 					  "pp5", "ppmmu5", "pp6", "ppmmu6";
 			resets = <&reset RESET_MALI>;
+
 			clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
 			clock-names = "bus", "core";
+
+			assigned-clocks = <&clkc CLKID_MALI>;
+			assigned-clock-rates = <318750000>;
+
 			operating-points-v2 = <&gpu_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 	};
 }; /* end of / */
 
+&aiu {
+	compatible = "amlogic,aiu-meson8", "amlogic,aiu";
+	clocks = <&clkc CLKID_AIU_GLUE>,
+		 <&clkc CLKID_I2S_OUT>,
+		 <&clkc CLKID_AOCLK_GATE>,
+		 <&clkc CLKID_CTS_AMCLK>,
+		 <&clkc CLKID_MIXER_IFACE>,
+		 <&clkc CLKID_IEC958>,
+		 <&clkc CLKID_IEC958_GATE>,
+		 <&clkc CLKID_CTS_MCLK_I958>,
+		 <&clkc CLKID_CTS_I958>;
+	clock-names = "pclk",
+		      "i2s_pclk",
+		      "i2s_aoclk",
+		      "i2s_mclk",
+		      "i2s_mixer",
+		      "spdif_pclk",
+		      "spdif_aoclk",
+		      "spdif_mclk",
+		      "spdif_mclk_sel";
+	resets = <&reset RESET_AIU>;
+};
+
 &aobus {
 	pmu: pmu@e0 {
 		compatible = "amlogic,meson8-pmu", "syscon";
-		reg = <0xe0 0x8>;
+		reg = <0xe0 0x18>;
 	};
 
 	pinctrl_aobus: pinctrl@84 {
@@ -273,6 +363,38 @@
 			gpio-ranges = <&pinctrl_aobus 0 0 16>;
 		};
 
+		i2s_am_clk_pins: i2s-am-clk-out {
+			mux {
+				groups = "i2s_am_clk_out_ao";
+				function = "i2s_ao";
+				bias-disable;
+			};
+		};
+
+		i2s_out_ao_clk_pins: i2s-ao-clk-out {
+			mux {
+				groups = "i2s_ao_clk_out_ao";
+				function = "i2s_ao";
+				bias-disable;
+			};
+		};
+
+		i2s_out_lr_clk_pins: i2s-lr-clk-out {
+			mux {
+				groups = "i2s_lr_clk_out_ao";
+				function = "i2s_ao";
+				bias-disable;
+			};
+		};
+
+		i2s_out_ch01_ao_pins: i2s-out-ch01 {
+			mux {
+				groups = "i2s_out_ch01_ao";
+				function = "i2s_ao";
+				bias-disable;
+			};
+		};
+
 		uart_ao_a_pins: uart_ao_a {
 			mux {
 				groups = "uart_tx_ao_a", "uart_rx_ao_a";
@@ -307,6 +429,14 @@
 	};
 };
 
+&ao_arc_rproc {
+	compatible = "amlogic,meson8-ao-arc", "amlogic,meson-mx-ao-arc";
+	amlogic,secbus2 = <&secbus2>;
+	sram = <&ao_arc_sram>;
+	resets = <&reset RESET_MEDIA_CPU>;
+	clocks = <&clkc CLKID_AO_MEDIA_CPU>;
+};
+
 &cbus {
 	reset: reset-controller@4404 {
 		compatible = "amlogic,meson8b-reset";
@@ -376,6 +506,32 @@
 			};
 		};
 
+		sdxc_a_pins: sdxc-a {
+			mux {
+				groups = "sdxc_d0_a", "sdxc_d13_a",
+					 "sdxc_clk_a", "sdxc_cmd_a";
+				function = "sdxc_a";
+				bias-pull-up;
+			};
+		};
+
+		sdxc_b_pins: sdxc-b {
+			mux {
+				groups = "sdxc_d0_b", "sdxc_d13_b",
+					 "sdxc_clk_b", "sdxc_cmd_b";
+				function = "sdxc_b";
+				bias-pull-up;
+			};
+		};
+
+		spdif_out_pins: spdif-out {
+			mux {
+				groups = "spdif_out";
+				function = "spdif";
+				bias-disable;
+			};
+		};
+
 		spi_nor_pins: nor {
 			mux {
 				groups = "nor_d", "nor_q", "nor_c", "nor_cs";
@@ -421,10 +577,24 @@
 				bias-disable;
 			};
 		};
+
+		xtal_32k_out_pins: xtal-32k-out {
+			mux {
+				groups = "xtal_32k_out";
+				function = "xtal";
+				bias-disable;
+			};
+		};
 	};
 };
 
 &ahb_sram {
+	ao_arc_sram: ao-arc-sram@0 {
+		compatible = "amlogic,meson8-ao-arc-sram";
+		reg = <0x0 0x8000>;
+		pool;
+	};
+
 	smp-sram@1ff80 {
 		compatible = "amlogic,meson8-smp-sram";
 		reg = <0x1ff80 0x8>;
@@ -445,6 +615,8 @@
 &ethmac {
 	clocks = <&clkc CLKID_ETH>;
 	clock-names = "stmmaceth";
+
+	power-domains = <&pwrc PWRC_MESON8_ETHERNET_MEM_ID>;
 };
 
 &gpio_intc {
@@ -455,9 +627,21 @@
 &hhi {
 	clkc: clock-controller {
 		compatible = "amlogic,meson8-clkc";
+		clocks = <&xtal>, <&ddr_clkc DDR_CLKID_DDR_PLL>;
+		clock-names = "xtal", "ddr_pll";
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 	};
+
+	pwrc: power-controller {
+		compatible = "amlogic,meson8-pwrc";
+		#power-domain-cells = <1>;
+		amlogic,ao-sysctrl = <&pmu>;
+		clocks = <&clkc CLKID_VPU>;
+		clock-names = "vpu";
+		assigned-clocks = <&clkc CLKID_VPU>;
+		assigned-clock-rates = <364285714>;
+	};
 };
 
 &hwrng {
@@ -484,6 +668,9 @@
 	arm,filter-ranges = <0x100000 0xc0000000>;
 	prefetch-data = <1>;
 	prefetch-instr = <1>;
+	arm,prefetch-offset = <7>;
+	arm,double-linefill = <1>;
+	arm,prefetch-drop = <1>;
 	arm,shared-override;
 };
 
@@ -529,14 +716,30 @@
 
 &saradc {
 	compatible = "amlogic,meson8-saradc", "amlogic,meson-saradc";
-	clocks = <&clkc CLKID_XTAL>,
-		<&clkc CLKID_SAR_ADC>;
+	clocks = <&xtal>, <&clkc CLKID_SAR_ADC>;
 	clock-names = "clkin", "core";
 	amlogic,hhi-sysctrl = <&hhi>;
 	nvmem-cells = <&temperature_calib>;
 	nvmem-cell-names = "temperature_calib";
 };
 
+&sdhc {
+	compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc";
+	clocks = <&xtal>,
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>,
+		 <&clkc CLKID_FCLK_DIV5>,
+		 <&clkc CLKID_SDHC>;
+	clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk";
+};
+
+&secbus {
+	secbus2: system-controller@4000 {
+		compatible = "amlogic,meson8-secbus2", "syscon";
+		reg = <0x4000 0x2000>;
+	};
+};
+
 &sdio {
 	compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio";
 	clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>;
@@ -548,32 +751,32 @@
 };
 
 &timer_abcde {
-	clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk";
 };
 
 &uart_AO {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_CLK81>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart", "amlogic,meson-ao-uart";
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_A {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_UART0>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_B {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_UART1>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_UART2>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/amlogic/meson8b-ec100.dts
index bed1dfef1985..3da47349eaaf 100644
--- a/arch/arm/boot/dts/meson8b-ec100.dts
+++ b/arch/arm/boot/dts/amlogic/meson8b-ec100.dts
@@ -27,6 +27,11 @@
 		reg = <0x40000000 0x40000000>;
 	};
 
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys-polled";
 		#address-cells = <1>;
@@ -65,15 +70,10 @@
 		timeout-ms = <20000>;
 	};
 
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&saradc 8>;
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "ec100:red:power";
 			/*
 			 * Needs to go LOW (together with the poweroff GPIO)
@@ -96,6 +96,32 @@
 		#clock-cells = <0>;
 	};
 
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "M8B-EC100";
+
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-rates = <270950400>,
+				       <294912000>,
+				       <393216000>;
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&rt5640>;
+			};
+		};
+	};
+
 	usb_vbus: regulator-usb-vbus {
 		/*
 		 * Silergy SY6288CCAC-GP 2A Power Distribution Switch.
@@ -148,7 +174,7 @@
 		regulator-min-microvolt = <860000>;
 		regulator-max-microvolt = <1140000>;
 
-		vin-supply = <&vcc_5v>;
+		pwm-supply = <&vcc_5v>;
 
 		pwms = <&pwm_cd 0 1148 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -232,7 +258,7 @@
 		regulator-min-microvolt = <860000>;
 		regulator-max-microvolt = <1140000>;
 
-		vin-supply = <&vcc_5v>;
+		pwm-supply = <&vcc_5v>;
 
 		pwms = <&pwm_cd 1 1148 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -242,6 +268,14 @@
 	};
 };
 
+&aiu {
+	status = "okay";
+
+	pinctrl-0 = <&i2s_am_clk_pins>, <&i2s_out_ao_clk_pins>,
+		    <&i2s_out_lr_clk_pins>, <&i2s_out_ch01_ao_pins>;
+	pinctrl-names = "default";
+};
+
 &cpu0 {
 	cpu-supply = <&vcck>;
 };
@@ -283,9 +317,19 @@
 
 	rt5640: codec@1c {
 		compatible = "realtek,rt5640";
+
 		reg = <0x1c>;
+
+		#sound-dai-cells = <0>;
+
 		interrupt-parent = <&gpio_intc>;
 		interrupts = <13 IRQ_TYPE_EDGE_BOTH>; /* GPIOAO_13 */
+
+		/*
+		 * TODO: realtek,ldo1-en-gpios is connected to GPIO_BSD_EN.
+		 * We currently cannot configure this pin correctly.
+		 * Luckily for us it's in the "right" state by default.
+		 */
 		realtek,in1-differential;
 	};
 };
@@ -299,6 +343,26 @@
 	vref-supply = <&vcc_1v8>;
 };
 
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	max-frequency = <50000000>;
+
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	no-sdio;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
 &sdio {
 	status = "okay";
 
@@ -377,7 +441,7 @@
 	status = "okay";
 	pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
 	pinctrl-names = "default";
-	clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_XTAL>;
+	clocks = <&xtal>, <&xtal>;
 	clock-names = "clkin0", "clkin1";
 };
 
diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/amlogic/meson8b-mxq.dts
index 6e39ad52e42d..7adedd3258c3 100644
--- a/arch/arm/boot/dts/meson8b-mxq.dts
+++ b/arch/arm/boot/dts/amlogic/meson8b-mxq.dts
@@ -27,11 +27,6 @@
 		reg = <0x40000000 0x40000000>;
 	};
 
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&saradc 8>;
-	};
-
 	vcck: regulator-vcck {
 		compatible = "pwm-regulator";
 
@@ -39,6 +34,8 @@
 		regulator-min-microvolt = <860000>;
 		regulator-max-microvolt = <1140000>;
 
+		pwm-supply = <&vcc_5v>;
+
 		pwms = <&pwm_cd 0 1148 0>;
 		pwm-dutycycle-range = <100 0>;
 
@@ -84,7 +81,7 @@
 		regulator-min-microvolt = <860000>;
 		regulator-max-microvolt = <1140000>;
 
-		vin-supply = <&vcc_5v>;
+		pwm-supply = <&vcc_5v>;
 
 		pwms = <&pwm_cd 1 1148 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -165,7 +162,7 @@
 	status = "okay";
 	pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
 	pinctrl-names = "default";
-	clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_XTAL>;
+	clocks = <&xtal>, <&xtal>;
 	clock-names = "clkin0", "clkin1";
 };
 
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts
index a24eccc354b9..941682844faf 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts
@@ -15,6 +15,7 @@
 	aliases {
 		serial0 = &uart_AO;
 		mmc0 = &sd_card_slot;
+		mmc1 = &sdhc;
 	};
 
 	chosen {
@@ -26,9 +27,14 @@
 		reg = <0x40000000 0x40000000>;
 	};
 
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
-		blue {
+		led-blue {
 			label = "c1:blue:alive";
 			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
@@ -79,11 +85,6 @@
 			  1800000 1>;
 	};
 
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&saradc 8>;
-	};
-
 	rtc32k_xtal: rtc32k-xtal-clk {
 		/* X3 in the schematics */
 		compatible = "fixed-clock";
@@ -130,7 +131,7 @@
 		regulator-min-microvolt = <860000>;
 		regulator-max-microvolt = <1140000>;
 
-		vin-supply = <&p5v0>;
+		pwm-supply = <&p5v0>;
 
 		pwms = <&pwm_cd 0 12218 0>;
 		pwm-dutycycle-range = <91 0>;
@@ -162,7 +163,7 @@
 		regulator-min-microvolt = <860000>;
 		regulator-max-microvolt = <1140000>;
 
-		vin-supply = <&p5v0>;
+		pwm-supply = <&p5v0>;
 
 		pwms = <&pwm_cd 1 12218 0>;
 		pwm-dutycycle-range = <91 0>;
@@ -202,9 +203,8 @@
 	pinctrl-0 = <&eth_rgmii_pins>;
 	pinctrl-names = "default";
 
-	phy-mode = "rgmii";
 	phy-handle = <&eth_phy>;
-	amlogic,tx-delay-ns = <4>;
+	phy-mode = "rgmii-id";
 
 	nvmem-cells = <&ethernet_mac_address>;
 	nvmem-cell-names = "mac-address";
@@ -219,7 +219,7 @@
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
@@ -281,19 +281,6 @@
 			  "J7 Header Pin 6", "J7 Header Pin 5",
 			  "J7 Header Pin 7", "HDMI_CEC",
 			  "SYS_LED", "", "";
-
-	/*
-	 * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller.
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &ir_receiver {
@@ -311,6 +298,26 @@
 	vref-supply = <&vcc_1v8>;
 };
 
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	max-frequency = <100000000>;
+
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	no-sdio;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+};
+
 &sdio {
 	status = "okay";
 
@@ -340,7 +347,7 @@
 	status = "okay";
 	pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
 	pinctrl-names = "default";
-	clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_XTAL>;
+	clocks = <&xtal>, <&xtal>;
 	clock-names = "clkin0", "clkin1";
 };
 
@@ -361,5 +368,16 @@
 };
 
 &usb1 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	hub@1 {
+		/* Genesys Logic GL852G usb hub */
+		compatible = "usb5e3,610";
+		reg = <1>;
+		vdd-supply = <&p5v0>;
+		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+	};
 };
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/amlogic/meson8b.dtsi
index 099bf8e711c9..5198f5177c2c 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8b.dtsi
@@ -4,10 +4,13 @@
  * Author: Carlo Caione <carlo@endlessm.com>
  */
 
+#include <dt-bindings/clock/meson8-ddr-clkc.h>
 #include <dt-bindings/clock/meson8b-clkc.h>
 #include <dt-bindings/gpio/meson8b-gpio.h>
+#include <dt-bindings/power/meson8-power.h>
 #include <dt-bindings/reset/amlogic,meson8b-reset.h>
 #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "meson.dtsi"
 
 / {
@@ -24,6 +27,7 @@
 			resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu1: cpu@201 {
@@ -35,6 +39,7 @@
 			resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu2: cpu@202 {
@@ -46,6 +51,7 @@
 			resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu3: cpu@203 {
@@ -57,6 +63,7 @@
 			resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>;
 			operating-points-v2 = <&cpu_opp_table>;
 			clocks = <&clkc CLKID_CPUCLK>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 	};
 
@@ -118,15 +125,15 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-255000000 {
 			opp-hz = /bits/ 64 <255000000>;
 			opp-microvolt = <1100000>;
 		};
-		opp-364300000 {
-			opp-hz = /bits/ 64 <364300000>;
+		opp-364285714 {
+			opp-hz = /bits/ 64 <364285714>;
 			opp-microvolt = <1100000>;
 		};
 		opp-425000000 {
@@ -165,6 +172,54 @@
 		};
 	};
 
+	thermal-zones {
+		soc {
+			polling-delay-passive = <250>; /* milliseconds */
+			polling-delay = <1000>; /* milliseconds */
+			thermal-sensors = <&thermal_sensor>;
+
+			cooling-maps {
+				map0 {
+					trip = <&soc_passive>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&soc_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				soc_passive: soc-passive {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				soc_hot: soc-hot {
+					temperature = <90000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				soc_critical: soc-critical {
+					temperature = <110000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	mmcbus: bus@c8000000 {
 		compatible = "simple-bus";
 		reg = <0xc8000000 0x8000>;
@@ -172,6 +227,14 @@
 		#size-cells = <1>;
 		ranges = <0x0 0xc8000000 0x8000>;
 
+		ddr_clkc: clock-controller@400 {
+			compatible = "amlogic,meson8b-ddr-clkc";
+			reg = <0x400 0x20>;
+			clocks = <&xtal>;
+			clock-names = "xtal";
+			#clock-cells = <1>;
+		};
+
 		dmcbus: bus@6000 {
 			compatible = "simple-bus";
 			reg = <0x6000 0x400>;
@@ -211,10 +274,34 @@
 			clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
 			clock-names = "bus", "core";
 			operating-points-v2 = <&gpu_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 	};
 }; /* end of / */
 
+&aiu {
+	compatible = "amlogic,aiu-meson8b", "amlogic,aiu";
+	clocks = <&clkc CLKID_AIU_GLUE>,
+		 <&clkc CLKID_I2S_OUT>,
+		 <&clkc CLKID_AOCLK_GATE>,
+		 <&clkc CLKID_CTS_AMCLK>,
+		 <&clkc CLKID_MIXER_IFACE>,
+		 <&clkc CLKID_IEC958>,
+		 <&clkc CLKID_IEC958_GATE>,
+		 <&clkc CLKID_CTS_MCLK_I958>,
+		 <&clkc CLKID_CTS_I958>;
+	clock-names = "pclk",
+		      "i2s_pclk",
+		      "i2s_aoclk",
+		      "i2s_mclk",
+		      "i2s_mixer",
+		      "spdif_pclk",
+		      "spdif_aoclk",
+		      "spdif_mclk",
+		      "spdif_mclk_sel";
+	resets = <&reset RESET_AIU>;
+};
+
 &aobus {
 	pmu: pmu@e0 {
 		compatible = "amlogic,meson8b-pmu", "syscon";
@@ -238,6 +325,46 @@
 			gpio-ranges = <&pinctrl_aobus 0 0 16>;
 		};
 
+		i2s_am_clk_pins: i2s-am-clk-out {
+			mux {
+				groups = "i2s_am_clk_out";
+				function = "i2s";
+				bias-disable;
+			};
+		};
+
+		i2s_out_ao_clk_pins: i2s-ao-clk-out {
+			mux {
+				groups = "i2s_ao_clk_out";
+				function = "i2s";
+				bias-disable;
+			};
+		};
+
+		i2s_out_lr_clk_pins: i2s-lr-clk-out {
+			mux {
+				groups = "i2s_lr_clk_out";
+				function = "i2s";
+				bias-disable;
+			};
+		};
+
+		i2s_out_ch01_ao_pins: i2s-out-ch01 {
+			mux {
+				groups = "i2s_out_01";
+				function = "i2s";
+				bias-disable;
+			};
+		};
+
+		spdif_out_1_pins: spdif-out-1 {
+			mux {
+				groups = "spdif_out_1";
+				function = "spdif_1";
+				bias-disable;
+			};
+		};
+
 		uart_ao_a_pins: uart_ao_a {
 			mux {
 				groups = "uart_tx_ao_a", "uart_rx_ao_a";
@@ -256,6 +383,14 @@
 	};
 };
 
+&ao_arc_rproc {
+	compatible = "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc";
+	amlogic,secbus2 = <&secbus2>;
+	sram = <&ao_arc_sram>;
+	resets = <&reset RESET_MEDIA_CPU>;
+	clocks = <&clkc CLKID_AO_MEDIA_CPU>;
+};
+
 &cbus {
 	reset: reset-controller@4404 {
 		compatible = "amlogic,meson8b-reset";
@@ -353,6 +488,16 @@
 			};
 		};
 
+		sdxc_c_pins: sdxc-c {
+			mux {
+				groups = "sdxc_d0_c", "sdxc_d13_c",
+					 "sdxc_d47_c", "sdxc_clk_c",
+					 "sdxc_cmd_c";
+				function = "sdxc_c";
+				bias-pull-up;
+			};
+		};
+
 		pwm_c1_pins: pwm-c1 {
 			mux {
 				groups = "pwm_c1";
@@ -390,6 +535,12 @@
 };
 
 &ahb_sram {
+	ao_arc_sram: ao-arc-sram@0 {
+		compatible = "amlogic,meson8b-ao-arc-sram";
+		reg = <0x0 0x8000>;
+		pool;
+	};
+
 	smp-sram@1ff80 {
 		compatible = "amlogic,meson8b-smp-sram";
 		reg = <0x1ff80 0x8>;
@@ -416,27 +567,56 @@
 
 	clocks = <&clkc CLKID_ETH>,
 		 <&clkc CLKID_MPLL2>,
-		 <&clkc CLKID_MPLL2>;
-	clock-names = "stmmaceth", "clkin0", "clkin1";
+		 <&clkc CLKID_MPLL2>,
+		 <&clkc CLKID_FCLK_DIV2>;
+	clock-names = "stmmaceth", "clkin0", "clkin1", "timing-adjustment";
 	rx-fifo-depth = <4096>;
 	tx-fifo-depth = <2048>;
 
 	resets = <&reset RESET_ETHERNET>;
 	reset-names = "stmmaceth";
+
+	power-domains = <&pwrc PWRC_MESON8_ETHERNET_MEM_ID>;
 };
 
 &gpio_intc {
-	compatible = "amlogic,meson-gpio-intc",
-		     "amlogic,meson8b-gpio-intc";
+	compatible = "amlogic,meson8b-gpio-intc",
+		     "amlogic,meson-gpio-intc";
 	status = "okay";
 };
 
 &hhi {
 	clkc: clock-controller {
-		compatible = "amlogic,meson8-clkc";
+		compatible = "amlogic,meson8b-clkc";
+		clocks = <&xtal>, <&ddr_clkc DDR_CLKID_DDR_PLL>;
+		clock-names = "xtal", "ddr_pll";
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 	};
+
+	pwrc: power-controller {
+		compatible = "amlogic,meson8b-pwrc";
+		#power-domain-cells = <1>;
+		amlogic,ao-sysctrl = <&pmu>;
+		resets = <&reset RESET_DBLK>,
+			 <&reset RESET_PIC_DC>,
+			 <&reset RESET_HDMI_APB>,
+			 <&reset RESET_HDMI_SYSTEM_RESET>,
+			 <&reset RESET_VENCI>,
+			 <&reset RESET_VENCP>,
+			 <&reset RESET_VDAC_4>,
+			 <&reset RESET_VENCL>,
+			 <&reset RESET_VIU>,
+			 <&reset RESET_VENC>,
+			 <&reset RESET_RDMA>;
+		reset-names = "dblk", "pic_dc", "hdmi_apb", "hdmi_system",
+			      "venci", "vencp", "vdac", "vencl", "viu",
+			      "venc", "rdma";
+		clocks = <&clkc CLKID_VPU>;
+		clock-names = "vpu";
+		assigned-clocks = <&clkc CLKID_VPU>;
+		assigned-clock-rates = <182142857>;
+	};
 };
 
 &hwrng {
@@ -463,6 +643,9 @@
 	arm,filter-ranges = <0x100000 0xc0000000>;
 	prefetch-data = <1>;
 	prefetch-instr = <1>;
+	arm,prefetch-offset = <7>;
+	arm,double-linefill = <1>;
+	arm,prefetch-drop = <1>;
 	arm,shared-override;
 };
 
@@ -508,14 +691,30 @@
 
 &saradc {
 	compatible = "amlogic,meson8b-saradc", "amlogic,meson-saradc";
-	clocks = <&clkc CLKID_XTAL>,
-		<&clkc CLKID_SAR_ADC>;
+	clocks = <&xtal>, <&clkc CLKID_SAR_ADC>;
 	clock-names = "clkin", "core";
 	amlogic,hhi-sysctrl = <&hhi>;
 	nvmem-cells = <&temperature_calib>;
 	nvmem-cell-names = "temperature_calib";
 };
 
+&sdhc {
+	compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc";
+	clocks = <&xtal>,
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>,
+		 <&clkc CLKID_FCLK_DIV5>,
+		 <&clkc CLKID_SDHC>;
+	clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk";
+};
+
+&secbus {
+	secbus2: system-controller@4000 {
+		compatible = "amlogic,meson8b-secbus2", "syscon";
+		reg = <0x4000 0x2000>;
+	};
+};
+
 &sdio {
 	compatible = "amlogic,meson8b-sdio", "amlogic,meson-mx-sdio";
 	clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>;
@@ -523,32 +722,32 @@
 };
 
 &timer_abcde {
-	clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk";
 };
 
 &uart_AO {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_CLK81>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart", "amlogic,meson-ao-uart";
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_A {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_UART0>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_B {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_UART1>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_XTAL>, <&clkc CLKID_UART2>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/amlogic/meson8m2-mxiii-plus.dts
index d54477b1001c..aa4d4bf70629 100644
--- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
+++ b/arch/arm/boot/dts/amlogic/meson8m2-mxiii-plus.dts
@@ -19,7 +19,6 @@
 		ethernet0 = &ethmac;
 		i2c0 = &i2c_AO;
 		serial0 = &uart_AO;
-		serial1 = &uart_A;
 		mmc0 = &sd_card_slot;
 	};
 
@@ -45,9 +44,17 @@
 		};
 	};
 
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&saradc 8>;
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		pinctrl-0 = <&xtal_32k_out_pins>;
+		pinctrl-names = "default";
+
+		reset-gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>,
+			      <&gpio_ao GPIOAO_6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&xtal_32k_out>;
+		clock-names = "ext_clock";
 	};
 
 	vcc_3v3: regulator-vcc3v3 {
@@ -56,6 +63,13 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	xtal_32k_out: xtal-32k-out-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32k_out";
+	};
 };
 
 &cpu0 {
@@ -69,9 +83,7 @@
 	pinctrl-names = "default";
 
 	phy-handle = <&eth_phy0>;
-	phy-mode = "rgmii";
-
-	amlogic,tx-delay-ns = <4>;
+	phy-mode = "rgmii-id";
 
 	mdio {
 		compatible = "snps,dwmac-mdio";
@@ -83,7 +95,7 @@
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -199,6 +211,27 @@
 	vref-supply = <&vddio_ao1v8>;
 };
 
+/* SDIO wifi */
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_a_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	disable-wp;
+	non-removable;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
 &sdio {
 	status = "okay";
 
@@ -229,6 +262,12 @@
 	pinctrl-0 = <&uart_a1_pins>, <&uart_a1_cts_rts_pins>;
 	pinctrl-names = "default";
 	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm20702a1";
+		shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+	};
 };
 
 &uart_AO {
diff --git a/arch/arm/boot/dts/meson8m2.dtsi b/arch/arm/boot/dts/amlogic/meson8m2.dtsi
index 5bde7f502007..6725dd9fd825 100644
--- a/arch/arm/boot/dts/meson8m2.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8m2.dtsi
@@ -30,8 +30,9 @@
 		0xc1108140 0x8>;
 	clocks = <&clkc CLKID_ETH>,
 		 <&clkc CLKID_MPLL2>,
-		 <&clkc CLKID_MPLL2>;
-	clock-names = "stmmaceth", "clkin0", "clkin1";
+		 <&clkc CLKID_MPLL2>,
+		 <&clkc CLKID_FCLK_DIV2>;
+	clock-names = "stmmaceth", "clkin0", "clkin1", "timing-adjustment";
 	resets = <&reset RESET_ETHERNET>;
 	reset-names = "stmmaceth";
 };
@@ -60,10 +61,41 @@
 	};
 };
 
+&pwrc {
+	compatible = "amlogic,meson8m2-pwrc";
+	resets = <&reset RESET_DBLK>,
+		 <&reset RESET_PIC_DC>,
+		 <&reset RESET_HDMI_APB>,
+		 <&reset RESET_HDMI_SYSTEM_RESET>,
+		 <&reset RESET_VENCI>,
+		 <&reset RESET_VENCP>,
+		 <&reset RESET_VDAC_4>,
+		 <&reset RESET_VENCL>,
+		 <&reset RESET_VIU>,
+		 <&reset RESET_VENC>,
+		 <&reset RESET_RDMA>;
+	reset-names = "dblk", "pic_dc", "hdmi_apb", "hdmi_system", "venci",
+		      "vencp", "vdac", "vencl", "viu", "venc", "rdma";
+	assigned-clocks = <&clkc CLKID_VPU>;
+	assigned-clock-rates = <364000000>;
+};
+
 &saradc {
 	compatible = "amlogic,meson8m2-saradc", "amlogic,meson-saradc";
 };
 
+&sdhc {
+	compatible = "amlogic,meson8m2-sdhc", "amlogic,meson-mx-sdhc";
+};
+
+&usb0_phy {
+	compatible = "amlogic,meson8m2-usb2-phy", "amlogic,meson-mx-usb2-phy";
+};
+
+&usb1_phy {
+	compatible = "amlogic,meson8m2-usb2-phy", "amlogic,meson-mx-usb2-phy";
+};
+
 &wdt {
 	compatible = "amlogic,meson8m2-wdt", "amlogic,meson8b-wdt";
 };
diff --git a/arch/arm/boot/dts/arm/Makefile b/arch/arm/boot/dts/arm/Makefile
new file mode 100644
index 000000000000..07ebb64e2cd0
--- /dev/null
+++ b/arch/arm/boot/dts/arm/Makefile
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_INTEGRATOR) += \
+	integratorap.dtb \
+	integratorap-im-pd1.dtb \
+	integratorcp.dtb
+dtb-$(CONFIG_ARCH_MPS2) += \
+	mps2-an385.dtb \
+	mps2-an399.dtb
+dtb-$(CONFIG_ARCH_REALVIEW) += \
+	arm-realview-pb1176.dtb \
+	arm-realview-pb11mp.dtb \
+	arm-realview-eb.dtb \
+	arm-realview-eb-bbrevd.dtb \
+	arm-realview-eb-11mp.dtb \
+	arm-realview-eb-11mp-bbrevd.dtb \
+	arm-realview-eb-11mp-ctrevb.dtb \
+	arm-realview-eb-11mp-bbrevd-ctrevb.dtb \
+	arm-realview-eb-a9mp.dtb \
+	arm-realview-eb-a9mp-bbrevd.dtb \
+	arm-realview-pba8.dtb \
+	arm-realview-pbx-a9.dtb
+dtb-$(CONFIG_ARCH_VERSATILE) += \
+	versatile-ab.dtb \
+	versatile-ab-ib2.dtb \
+	versatile-pb.dtb
+dtb-$(CONFIG_ARCH_VEXPRESS) += \
+	vexpress-v2p-ca5s.dtb \
+	vexpress-v2p-ca9.dtb \
+	vexpress-v2p-ca15-tc1.dtb \
+	vexpress-v2p-ca15_a7.dtb
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd-ctrevb.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd-ctrevb.dts
index e18769df9fd9..e18769df9fd9 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd-ctrevb.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd-ctrevb.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd.dts
index 26b1c69e9f43..26b1c69e9f43 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp-ctrevb.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-ctrevb.dts
index e68527b0d552..e68527b0d552 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp-ctrevb.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-ctrevb.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp.dts
index aac1edd4b227..aac1edd4b227 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-a9mp-bbrevd.dts b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp-bbrevd.dts
index 42efac7496ef..42efac7496ef 100644
--- a/arch/arm/boot/dts/arm-realview-eb-a9mp-bbrevd.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp-bbrevd.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-a9mp.dts b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp.dts
index 967684b3636c..967684b3636c 100644
--- a/arch/arm/boot/dts/arm-realview-eb-a9mp.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dts b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dts
index f533c8b49d97..f533c8b49d97 100644
--- a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dtsi b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dtsi
index a79e1d1d30a7..a79e1d1d30a7 100644
--- a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dtsi
diff --git a/arch/arm/boot/dts/arm-realview-eb-mp.dtsi b/arch/arm/boot/dts/arm/arm-realview-eb-mp.dtsi
index 29b636fce23f..26783d053ac7 100644
--- a/arch/arm/boot/dts/arm-realview-eb-mp.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-mp.dtsi
@@ -59,7 +59,7 @@
 			interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		L2: l2-cache {
+		L2: cache-controller {
 			compatible = "arm,l220-cache";
 			reg = <0x1f002000 0x1000>;
 			interrupt-parent = <&intc>;
diff --git a/arch/arm/boot/dts/arm-realview-eb.dts b/arch/arm/boot/dts/arm/arm-realview-eb.dts
index 15431077f00c..15431077f00c 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb.dtsi b/arch/arm/boot/dts/arm/arm-realview-eb.dtsi
index fe0207b88053..fbb2258b451f 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-eb.dtsi
@@ -148,7 +148,7 @@
 	usb: usb@4f000000 {
 		compatible = "nxp,usb-isp1761";
 		reg = <0x4f000000 0x20000>;
-		port1-otg;
+		dr_mode = "peripheral";
 	};
 
 	bridge {
@@ -198,96 +198,112 @@
 		syscon: syscon@10000000 {
 			compatible = "arm,realview-eb-syscon", "syscon", "simple-mfd";
 			reg = <0x10000000 0x1000>;
+			ranges = <0x0 0x10000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-			led@08.0 {
+			led@8,0 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x01>;
 				label = "versatile:0";
 				linux,default-trigger = "heartbeat";
 				default-state = "on";
 			};
-			led@08.1 {
+			led@8,1 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x02>;
 				label = "versatile:1";
 				linux,default-trigger = "mmc0";
 				default-state = "off";
 			};
-			led@08.2 {
+			led@8,2 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x04>;
 				label = "versatile:2";
 				linux,default-trigger = "cpu0";
 				default-state = "off";
 			};
-			led@08.3 {
+			led@8,3 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x08>;
 				label = "versatile:3";
 				default-state = "off";
 			};
-			led@08.4 {
+			led@8,4 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x10>;
 				label = "versatile:4";
 				default-state = "off";
 			};
-			led@08.5 {
+			led@8,5 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x20>;
 				label = "versatile:5";
 				default-state = "off";
 			};
-			led@08.6 {
+			led@8,6 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x40>;
 				label = "versatile:6";
 				default-state = "off";
 			};
-			led@08.7 {
+			led@8,7 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x80>;
 				label = "versatile:7";
 				default-state = "off";
 			};
-			oscclk0: osc0@0c {
+			oscclk0: clock-controller@c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x0c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x0C>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk1: osc1@10 {
+			oscclk1: clock-controller@10 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x10 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x10>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk2: osc2@14 {
+			oscclk2: clock-controller@14 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x14 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x14>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk3: osc3@18 {
+			oscclk3: clock-controller@18 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x18 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x18>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk4: osc4@1c {
+			oscclk4: clock-controller@1c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x1c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x1c>;
@@ -383,14 +399,14 @@
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		wdog: watchdog@10010000 {
 			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x10010000 0x1000>;
 			clocks = <&wdogclk>, <&pclk>;
-			clock-names = "wdogclk", "apb_pclk";
+			clock-names = "wdog_clk", "apb_pclk";
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/arm-realview-pb1176.dts b/arch/arm/boot/dts/arm/arm-realview-pb1176.dts
index 2625ce66f8e7..efed325af88d 100644
--- a/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pb1176.dts
@@ -166,7 +166,7 @@
 		reg = <0x3b000000 0x20000>;
 		interrupt-parent = <&intc_fpga1176>;
 		interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
-		port1-otg;
+		dr_mode = "peripheral";
 	};
 
 	bridge {
@@ -216,96 +216,112 @@
 		syscon: syscon@10000000 {
 			compatible = "arm,realview-pb1176-syscon", "syscon", "simple-mfd";
 			reg = <0x10000000 0x1000>;
+			ranges = <0x0 0x10000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-			led@08.0 {
+			led@8,0 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x01>;
 				label = "versatile:0";
 				linux,default-trigger = "heartbeat";
 				default-state = "on";
 			};
-			led@08.1 {
+			led@8,1 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x02>;
 				label = "versatile:1";
 				linux,default-trigger = "mmc0";
 				default-state = "off";
 			};
-			led@08.2 {
+			led@8,2 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x04>;
 				label = "versatile:2";
 				linux,default-trigger = "cpu0";
 				default-state = "off";
 			};
-			led@08.3 {
+			led@8,3 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x08>;
 				label = "versatile:3";
 				default-state = "off";
 			};
-			led@08.4 {
+			led@8,4 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x10>;
 				label = "versatile:4";
 				default-state = "off";
 			};
-			led@08.5 {
+			led@8,5 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x20>;
 				label = "versatile:5";
 				default-state = "off";
 			};
-			led@08.6 {
+			led@8,6 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x40>;
 				label = "versatile:6";
 				default-state = "off";
 			};
-			led@08.7 {
+			led@8,7 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x80>;
 				label = "versatile:7";
 				default-state = "off";
 			};
-			oscclk0: osc0@0c {
+			oscclk0: clock-controller@c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x0c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x0C>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk1: osc1@10 {
+			oscclk1: clock-controller@10 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x10 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x10>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk2: osc2@14 {
+			oscclk2: clock-controller@14 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x14 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x14>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk3: osc3@18 {
+			oscclk3: clock-controller@18 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x18 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x18>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk4: osc4@1c {
+			oscclk4: clock-controller@1c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x1c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x1c>;
@@ -323,7 +339,7 @@
 			      <0x10120000 0x100>;
 		};
 
-		L2: l2-cache {
+		L2: cache-controller {
 			compatible = "arm,l220-cache";
 			reg = <0x10110000 0x1000>;
 			interrupt-parent = <&intc_dc1176>;
@@ -394,7 +410,7 @@
 			interrupt-parent = <&intc_dc1176>;
 			interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		pb1176_serial0: serial@1010c000 {
diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm/arm-realview-pb11mp.dts
index c69cf7ddbe61..89103d54ecc1 100644
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pb11mp.dts
@@ -92,7 +92,7 @@
 		      <0x1f000100 0x100>;
 	};
 
-	L2: l2-cache {
+	L2: cache-controller {
 		compatible = "arm,l220-cache";
 		reg = <0x1f002000 0x1000>;
 		interrupt-parent = <&intc_tc11mp>;
@@ -303,114 +303,132 @@
 		pb11mp_syscon: syscon@10000000 {
 			compatible = "arm,realview-pb11mp-syscon", "syscon", "simple-mfd";
 			reg = <0x10000000 0x1000>;
+			ranges = <0x0 0x10000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-			led@08.0 {
+			led@8,0 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x01>;
 				label = "versatile:0";
 				linux,default-trigger = "heartbeat";
 				default-state = "on";
 			};
-			led@08.1 {
+			led@8,1 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x02>;
 				label = "versatile:1";
 				linux,default-trigger = "mmc0";
 				default-state = "off";
 			};
-			led@08.2 {
+			led@8,2 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x04>;
 				label = "versatile:2";
 				linux,default-trigger = "cpu0";
 				default-state = "off";
 			};
-			led@08.3 {
+			led@8,3 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x08>;
 				label = "versatile:3";
 				linux,default-trigger = "cpu1";
 				default-state = "off";
 			};
-			led@08.4 {
+			led@8,4 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x10>;
 				label = "versatile:4";
 				linux,default-trigger = "cpu2";
 				default-state = "off";
 			};
-			led@08.5 {
+			led@8,5 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x20>;
 				label = "versatile:5";
 				linux,default-trigger = "cpu3";
 				default-state = "off";
 			};
-			led@08.6 {
+			led@8,6 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x40>;
 				label = "versatile:6";
 				default-state = "off";
 			};
-			led@08.7 {
+			led@8,7 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x80>;
 				label = "versatile:7";
 				default-state = "off";
 			};
 
-			oscclk0: osc0@0c {
+			oscclk0: clock-controller@c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x0c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x0C>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk1: osc1@10 {
+			oscclk1: clock-controller@10 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x10 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x10>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk2: osc2@14 {
+			oscclk2: clock-controller@14 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x14 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x14>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk3: osc3@18 {
+			oscclk3: clock-controller@18 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x18 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x18>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk4: osc4@1c {
+			oscclk4: clock-controller@1c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x1c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x1c>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk5: osc5@d4 {
+			oscclk5: clock-controller@d4 {
 				compatible = "arm,syscon-icst307";
+				reg = <0xd4 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0xd4>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk6: osc6@d8 {
+			oscclk6: clock-controller@d8 {
 				compatible = "arm,syscon-icst307";
+				reg = <0xd8 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0xd8>;
@@ -537,7 +555,7 @@
 			interrupt-parent = <&intc_pb11mp>;
 			interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		watchdog@1000f000 {
@@ -546,7 +564,7 @@
 			interrupt-parent = <&intc_pb11mp>;
 			interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&wdogclk>, <&pclk>;
-			clock-names = "wdogclk", "apb_pclk";
+			clock-names = "wdog_clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -556,7 +574,7 @@
 			interrupt-parent = <&intc_pb11mp>;
 			interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&wdogclk>, <&pclk>;
-			clock-names = "wdogclk", "apb_pclk";
+			clock-names = "wdog_clk", "apb_pclk";
 		};
 
 		timer01: timer@10011000 {
@@ -568,8 +586,8 @@
 			clocks = <&sp810_syscon 0>,
 			         <&sp810_syscon 1>,
 				 <&pclk>;
-			clock-names = "timerclk0",
-				    "timerclk1",
+			clock-names = "timer0clk",
+				    "timer1clk",
 				    "apb_pclk";
 		};
 
@@ -582,8 +600,8 @@
 			clocks = <&sp810_syscon 2>,
 			         <&sp810_syscon 3>,
 				 <&pclk>;
-			clock-names = "timerclk2",
-				    "timerclk3",
+			clock-names = "timer0clk",
+				    "timer1clk",
 				    "apb_pclk";
 		};
 
@@ -645,16 +663,16 @@
 		timer45: timer@10018000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x10018000 0x1000>;
-			clocks = <&timclk>, <&pclk>;
-			clock-names = "timer", "apb_pclk";
+			clocks = <&timclk>, <&timclk>, <&pclk>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
 		timer67: timer@10019000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x10019000 0x1000>;
-			clocks = <&timclk>, <&pclk>;
-			clock-names = "timer", "apb_pclk";
+			clocks = <&timclk>, <&timclk>, <&pclk>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -712,7 +730,7 @@
 			reg = <0x4f000000 0x20000>;
 			interrupt-parent = <&intc_tc11mp>;
 			interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>;
-			port1-otg;
+			dr_mode = "peripheral";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/arm-realview-pba8.dts b/arch/arm/boot/dts/arm/arm-realview-pba8.dts
index d3238c252b59..d3238c252b59 100644
--- a/arch/arm/boot/dts/arm-realview-pba8.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pba8.dts
diff --git a/arch/arm/boot/dts/arm-realview-pbx-a9.dts b/arch/arm/boot/dts/arm/arm-realview-pbx-a9.dts
index 90d00b407f85..85d3968fbb91 100644
--- a/arch/arm/boot/dts/arm-realview-pbx-a9.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pbx-a9.dts
@@ -60,7 +60,7 @@
 		};
 	};
 
-	L2: l2-cache {
+	L2: cache-controller {
 		compatible = "arm,pl310-cache";
 		reg = <0x1f002000 0x1000>;
 		cache-unified;
diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm/arm-realview-pbx.dtsi
index 09f3f544f3a7..ec1507c5147c 100644
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-pbx.dtsi
@@ -164,7 +164,7 @@
 	usb: usb@4f000000 {
 		compatible = "nxp,usb-isp1761";
 		reg = <0x4f000000 0x20000>;
-		port1-otg;
+		dr_mode = "peripheral";
 	};
 
 	bridge {
@@ -210,7 +210,7 @@
 		};
 	};
 
-	soc: soc@0 {
+	soc: soc {
 		compatible = "arm,realview-pbx-soc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -220,96 +220,112 @@
 		syscon: syscon@10000000 {
 			compatible = "arm,realview-pbx-syscon", "syscon", "simple-mfd";
 			reg = <0x10000000 0x1000>;
+			ranges = <0x0 0x10000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-			led@08.0 {
+			led@8,0 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x01>;
 				label = "versatile:0";
 				linux,default-trigger = "heartbeat";
 				default-state = "on";
 			};
-			led@08.1 {
+			led@8,1 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x02>;
 				label = "versatile:1";
 				linux,default-trigger = "mmc0";
 				default-state = "off";
 			};
-			led@08.2 {
+			led@8,2 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x04>;
 				label = "versatile:2";
 				linux,default-trigger = "cpu0";
 				default-state = "off";
 			};
-			led@08.3 {
+			led@8,3 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x08>;
 				label = "versatile:3";
 				default-state = "off";
 			};
-			led@08.4 {
+			led@8,4 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x10>;
 				label = "versatile:4";
 				default-state = "off";
 			};
-			led@08.5 {
+			led@8,5 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x20>;
 				label = "versatile:5";
 				default-state = "off";
 			};
-			led@08.6 {
+			led@8,6 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x40>;
 				label = "versatile:6";
 				default-state = "off";
 			};
-			led@08.7 {
+			led@8,7 {
 				compatible = "register-bit-led";
+				reg = <0x08 0x04>;
 				offset = <0x08>;
 				mask = <0x80>;
 				label = "versatile:7";
 				default-state = "off";
 			};
-			oscclk0: osc0@0c {
+			oscclk0: clock-controller@c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x0c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x0C>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk1: osc1@10 {
+			oscclk1: clock-controller@10 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x10 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x10>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk2: osc2@14 {
+			oscclk2: clock-controller@14 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x14 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x14>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk3: osc3@18 {
+			oscclk3: clock-controller@18 {
 				compatible = "arm,syscon-icst307";
+				reg = <0x18 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x18>;
 				clocks = <&xtal24mhz>;
 			};
-			oscclk4: osc4@1c {
+			oscclk4: clock-controller@1c {
 				compatible = "arm,syscon-icst307";
+				reg = <0x1c 0x04>;
 				#clock-cells = <0>;
 				lock-offset = <0x20>;
 				vco-offset = <0x1c>;
@@ -374,14 +390,14 @@
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		wdog0: watchdog@1000f000 {
 			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x1000f000 0x1000>;
 			clocks = <&wdogclk>, <&pclk>;
-			clock-names = "wdogclk", "apb_pclk";
+			clock-names = "wdog_clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -389,7 +405,7 @@
 			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x10010000 0x1000>;
 			clocks = <&wdogclk>, <&pclk>;
-			clock-names = "wdogclk", "apb_pclk";
+			clock-names = "wdog_clk", "apb_pclk";
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/integrator.dtsi b/arch/arm/boot/dts/arm/integrator.dtsi
index 602f74d2c758..7f1c8ee9dd8a 100644
--- a/arch/arm/boot/dts/integrator.dtsi
+++ b/arch/arm/boot/dts/arm/integrator.dtsi
@@ -15,10 +15,14 @@
 	core-module@10000000 {
 		compatible = "arm,core-module-integrator", "syscon", "simple-mfd";
 		reg = <0x10000000 0x200>;
+		ranges = <0x0 0x10000000 0x200>;
+		#address-cells = <1>;
+		#size-cells = <1>;
 
 		/* Use core module LED to indicate CPU load */
-		led@c.0 {
+		led@c,0 {
 			compatible = "register-bit-led";
+			reg = <0x0c 0x04>;
 			offset = <0x0c>;
 			mask = <0x01>;
 			label = "integrator:core_module";
@@ -84,12 +88,12 @@
 			interrupts = <8>;
 		};
 
-		uart@16000000 {
+		serial@16000000 {
 			reg = <0x16000000 0x1000>;
 			interrupts = <1>;
 		};
 
-		uart@17000000 {
+		serial@17000000 {
 			reg = <0x17000000 0x1000>;
 			interrupts = <2>;
 		};
@@ -104,35 +108,42 @@
 			interrupts = <4>;
 		};
 
-		syscon {
+		syscon@1a000000 {
 			/* Debug registers mapped as syscon */
 			compatible = "syscon", "simple-mfd";
 			reg = <0x1a000000 0x10>;
+			ranges = <0x0 0x1a000000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
-			led@4.0 {
+			led@4,0 {
 				compatible = "register-bit-led";
+				reg = <0x04 0x04>;
 				offset = <0x04>;
 				mask = <0x01>;
 				label = "integrator:green0";
 				linux,default-trigger = "heartbeat";
 				default-state = "on";
 			};
-			led@4.1 {
+			led@4,1 {
 				compatible = "register-bit-led";
+				reg = <0x04 0x04>;
 				offset = <0x04>;
 				mask = <0x02>;
 				label = "integrator:yellow";
 				default-state = "off";
 			};
-			led@4.2 {
+			led@4,2 {
 				compatible = "register-bit-led";
+				reg = <0x04 0x04>;
 				offset = <0x04>;
 				mask = <0x04>;
 				label = "integrator:red";
 				default-state = "off";
 			};
-			led@4.3 {
+			led@4,3 {
 				compatible = "register-bit-led";
+				reg = <0x04 0x04>;
 				offset = <0x04>;
 				mask = <0x08>;
 				label = "integrator:green1";
diff --git a/arch/arm/boot/dts/arm/integratorap-im-pd1.dts b/arch/arm/boot/dts/arm/integratorap-im-pd1.dts
new file mode 100644
index 000000000000..7072a70da00d
--- /dev/null
+++ b/arch/arm/boot/dts/arm/integratorap-im-pd1.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree for the ARM Integrator/AP platform
+ * with the IM-PD1 example logical module mounted.
+ */
+
+#include "integratorap.dts"
+
+/ {
+	model = "ARM Integrator/AP with IM-PD1";
+	compatible = "arm,integrator-ap";
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		impd1_ram: vram@c2000000 {
+			/* 1 MB of designated video RAM on the IM-PD1 */
+			compatible = "shared-dma-pool";
+			reg = <0xc2000000 0x00100000>;
+			no-map;
+		};
+	};
+};
+
+&lm0 {
+	syscon@0 {
+		compatible = "arm,im-pd1-syscon", "syscon";
+		reg = <0x00000000 0x1000>;
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		vco1: clock-controller@0 {
+			compatible = "arm,impd1-vco1";
+			reg = <0x00 0x04>;
+			#clock-cells = <0>;
+			lock-offset = <0x08>;
+			vco-offset = <0x00>;
+			clocks = <&sysclk>;
+			clock-output-names = "IM-PD1-VCO1";
+		};
+
+		vco2: clock-controller@4 {
+			compatible = "arm,impd1-vco2";
+			reg = <0x04 0x04>;
+			#clock-cells = <0>;
+			lock-offset = <0x08>;
+			vco-offset = <0x04>;
+			clocks = <&sysclk>;
+			clock-output-names = "IM-PD1-VCO2";
+		};
+	};
+
+	/* Also used for the Smart Card Interface SCI */
+	impd1_uartclk: clock@1_4 {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clock-div = <4>;
+		clock-mult = <1>;
+		clocks = <&vco2>;
+		clock-output-names = "VCO2_DIV4";
+	};
+
+	/* For the SSP the clock is divided by 64 */
+	impd1_sspclk: clock@1_64 {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clock-div = <64>;
+		clock-mult = <1>;
+		clocks = <&vco2>;
+		clock-output-names = "VCO2_DIV64";
+	};
+
+	/* Fixed regulator for the MMC */
+	impd1_3v3: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	/* Push buttons on the IM-PD1 */
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@0 {
+			debounce-interval = <50>;
+			linux,code = <KEY_UP>;
+			label = "UP";
+			gpios = <&impd1_gpio1 0 GPIO_ACTIVE_HIGH>;
+		};
+		button@1 {
+			debounce-interval = <50>;
+			linux,code = <KEY_DOWN>;
+			label = "DOWN";
+			gpios = <&impd1_gpio1 1 GPIO_ACTIVE_HIGH>;
+		};
+		button@2 {
+			debounce-interval = <50>;
+			linux,code = <KEY_LEFT>;
+			label = "LEFT";
+			gpios = <&impd1_gpio1 2 GPIO_ACTIVE_HIGH>;
+		};
+		button@3 {
+			debounce-interval = <50>;
+			linux,code = <KEY_RIGHT>;
+			label = "UP";
+			gpios = <&impd1_gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+		button@4 {
+			debounce-interval = <50>;
+			linux,code = <KEY_ESC>;
+			label = "ESC";
+			gpios = <&impd1_gpio1 4 GPIO_ACTIVE_HIGH>;
+		};
+		button@5 {
+			debounce-interval = <50>;
+			linux,code = <KEY_ENTER>;
+			label = "ENTER";
+			gpios = <&impd1_gpio1 5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+
+	bridge {
+		compatible = "ti,ths8134b", "ti,ths8134";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+					vga_bridge_in: endpoint {
+					remote-endpoint = <&clcd_pads_vga_dac>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				vga_bridge_out: endpoint {
+					remote-endpoint = <&vga_con_in>;
+				};
+			};
+		};
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_con_in: endpoint {
+				remote-endpoint = <&vga_bridge_out>;
+			};
+		};
+	};
+
+	serial@100000 {
+		compatible = "arm,pl011", "arm,primecell";
+		reg = <0x00100000 0x1000>;
+		interrupts-extended = <&impd1_vic 1>;
+		clocks = <&impd1_uartclk>, <&sysclk>;
+		clock-names = "uartclk", "apb_pclk";
+	};
+
+	serial@200000 {
+		compatible = "arm,pl011", "arm,primecell";
+		reg = <0x00200000 0x1000>;
+		interrupts-extended = <&impd1_vic 2>;
+		clocks = <&impd1_uartclk>, <&sysclk>;
+		clock-names = "uartclk", "apb_pclk";
+	};
+
+	spi@300000 {
+		compatible = "arm,pl022", "arm,primecell";
+		reg = <0x00300000 0x1000>;
+		interrupts-extended = <&impd1_vic 3>;
+		clocks = <&impd1_sspclk>, <&sysclk>;
+		clock-names = "sspclk", "apb_pclk";
+	};
+
+	impd1_gpio0: gpio@400000 {
+		compatible = "arm,pl061", "arm,primecell";
+		reg = <0x00400000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts-extended = <&impd1_vic 4>;
+		clocks = <&sysclk>;
+		clock-names = "apb_pclk";
+	};
+
+	impd1_gpio1: gpio@500000 {
+		compatible = "arm,pl061", "arm,primecell";
+		reg = <0x00500000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts-extended = <&impd1_vic 5>;
+		clocks = <&sysclk>;
+		clock-names = "apb_pclk";
+	};
+
+	rtc@600000 {
+		compatible = "arm,pl030", "arm,primecell";
+		reg = <0x00600000 0x1000>;
+		interrupts-extended = <&impd1_vic 6>;
+		clocks = <&sysclk>;
+		clock-names = "apb_pclk";
+	};
+
+	mmc@700000 {
+		compatible = "arm,pl181", "arm,primecell";
+		reg = <0x00700000 0x1000>;
+		interrupts-extended = <&impd1_vic 7>,
+				    <&impd1_vic 8>;
+		clocks = <&sysclk>, <&sysclk>;
+		clock-names = "mclk", "apb_pclk";
+		bus-width = <1>;
+		max-frequency = <515633>;
+		vmmc-supply = <&impd1_3v3>;
+		wp-gpios = <&impd1_gpio0 3 GPIO_ACTIVE_HIGH>;
+		cd-gpios = <&impd1_gpio0 4 GPIO_ACTIVE_LOW>;
+	};
+
+	aaci@800000 {
+		compatible = "arm,pl041", "arm,primecell";
+		reg = <0x00800000 0x1000>;
+		interrupts-extended = <&impd1_vic 9>;
+		clocks = <&sysclk>;
+		clock-names = "apb_pclk";
+	};
+
+	display@1000000 {
+		compatible = "arm,pl110", "arm,primecell";
+		reg = <0x01000000 0x1000>;
+		interrupts-extended = <&impd1_vic 11>;
+		clocks = <&vco1>, <&sysclk>;
+		clock-names = "clcdclk", "apb_pclk";
+		/* 640x480 16bpp @ 25.175MHz is 36827428 bytes/s */
+		max-memory-bandwidth = <40000000>;
+		memory-region = <&impd1_ram>;
+		dma-ranges;
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clcd_pads_vga_dac: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&vga_bridge_in>;
+				arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+			};
+		};
+	};
+
+	impd1_vic: interrupt-controller@3000000 {
+		compatible = "arm,pl192-vic";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x03000000 0x1000>;
+		/* Valid interrupts, 0-9 and 11 */
+		valid-mask = <0x00000bff>;
+		/* LM site 0 has IRQ 9 on the PIC */
+		interrupts-extended = <&pic 9>;
+	};
+};
diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/arm/integratorap.dts
index 94d2ff9836d0..d9927d3181dc 100644
--- a/arch/arm/boot/dts/integratorap.dts
+++ b/arch/arm/boot/dts/arm/integratorap.dts
@@ -4,12 +4,13 @@
  */
 
 /dts-v1/;
-/include/ "integrator.dtsi"
+#include "integrator.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "ARM Integrator/AP";
 	compatible = "arm,integrator-ap";
-	dma-ranges = <0x80000000 0x0 0x80000000>;
 
 	cpus {
 		#address-cells = <1>;
@@ -87,8 +88,9 @@
 		};
 
 		/* Oscillator on the core module, clocks the CPU core */
-		cmosc: cmosc@24M {
+		cmosc: clock-controller@8 {
 			compatible = "arm,syscon-icst525-integratorap-cm";
+			reg = <0x08 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x14>;
 			vco-offset = <0x08>;
@@ -96,8 +98,9 @@
 		};
 
 		/* Auxilary oscillator on the core module, 32.369MHz at boot */
-		auxosc: auxosc@24M {
+		auxosc: clock-controller@1c {
 			compatible = "arm,syscon-icst525";
+			reg = <0x1c 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x14>;
 			vco-offset = <0x1c>;
@@ -108,16 +111,17 @@
 	syscon {
 		compatible = "arm,integrator-ap-syscon", "syscon";
 		reg = <0x11000000 0x100>;
-		interrupt-parent = <&pic>;
-		/* These are the logical module IRQs */
-		interrupts = <9>, <10>, <11>, <12>;
+		ranges = <0x0 0x11000000 0x100>;
+		#size-cells = <1>;
+		#address-cells = <1>;
 
 		/*
 		 * SYSCLK clocks PCIv3 bridge, system controller and the
 		 * logic modules.
 		 */
-		sysclk: apsys@24M {
+		sysclk: clock-controller@4 {
 			compatible = "arm,syscon-icst525-integratorap-sys";
+			reg = <0x04 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x1c>;
 			vco-offset = <0x04>;
@@ -125,8 +129,9 @@
 		};
 
 		/* One-bit control for the PCI bus clock (33 or 25 MHz) */
-		pciclk: pciclk@24M {
+		pciclk: clock-controller@4,8 {
 			compatible = "arm,syscon-icst525-integratorap-pci";
+			reg = <0x04 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x1c>;
 			vco-offset = <0x04>;
@@ -153,8 +158,9 @@
 		valid-mask = <0x003fffff>;
 	};
 
-	pci: pciv3@62000000 {
+	pci: pci@62000000 {
 		compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
+		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
@@ -212,14 +218,14 @@
 			clock-names = "apb_pclk";
 		};
 
-		uart0: uart@16000000 {
+		uart0: serial@16000000 {
 			compatible = "arm,pl010", "arm,primecell";
 			arm,primecell-periphid = <0x00041010>;
 			clocks = <&uartclk>, <&pclk>;
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart1: uart@17000000 {
+		uart1: serial@17000000 {
 			compatible = "arm,pl010", "arm,primecell";
 			arm,primecell-periphid = <0x00041010>;
 			clocks = <&uartclk>, <&pclk>;
@@ -240,4 +246,50 @@
 			clock-names = "KMIREFCLK", "apb_pclk";
 		};
 	};
+
+	/*
+	 * Logic module bus, we support up to 4 logical modules
+	 * They appear at 0xc0000000, 0xd0000000, 0xe0000000 and 0xf0000000
+	 * and use interrupts 9, 10, 11 and 12 respectively.
+	 */
+	bus@c0000000 {
+		compatible = "arm,integrator-ap-lm";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0xc0000000 0xc0000000 0x40000000>;
+		dma-ranges;
+
+		lm0: bus@c0000000 {
+			compatible = "simple-bus";
+			ranges = <0x00000000 0xc0000000 0x10000000>;
+			dma-ranges = <0x00000000 0xc0000000 0x10000000>;
+			reg = <0xc0000000 0x10000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+		lm1: bus@d0000000 {
+			compatible = "simple-bus";
+			ranges = <0x00000000 0xd0000000 0x10000000>;
+			dma-ranges = <0x00000000 0xd0000000 0x10000000>;
+			reg = <0xd0000000 0x10000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+		lm2: bus@e0000000 {
+			compatible = "simple-bus";
+			ranges = <0x00000000 0xe0000000 0x10000000>;
+			dma-ranges = <0x00000000 0xe0000000 0x10000000>;
+			reg = <0xe0000000 0x10000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+		lm3: bus@f0000000 {
+			compatible = "simple-bus";
+			ranges = <0x00000000 0xf0000000 0x10000000>;
+			dma-ranges = <0x00000000 0xf0000000 0x10000000>;
+			reg = <0xf0000000 0x10000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/integratorcp.dts b/arch/arm/boot/dts/arm/integratorcp.dts
index 01fa229e1bd0..c011333eb165 100644
--- a/arch/arm/boot/dts/integratorcp.dts
+++ b/arch/arm/boot/dts/arm/integratorcp.dts
@@ -92,8 +92,9 @@
 		};
 
 		/* Oscillator on the core module, clocks the CPU core */
-		cmcore: cmosc@24M {
+		cmcore: clock-controller@8 {
 			compatible = "arm,syscon-icst525-integratorcp-cm-core";
+			reg = <0x08 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x14>;
 			vco-offset = <0x08>;
@@ -101,8 +102,9 @@
 		};
 
 		/* Oscillator on the core module, clocks the memory bus */
-		cmmem: cmosc@24M {
+		cmmem: clock-controller@8,12 {
 			compatible = "arm,syscon-icst525-integratorcp-cm-mem";
+			reg = <0x08 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x14>;
 			vco-offset = <0x08>;
@@ -110,8 +112,9 @@
 		};
 
 		/* Auxilary oscillator on the core module, clocks the CLCD */
-		auxosc: auxosc@24M {
+		auxosc: clock-controller@1c {
 			compatible = "arm,syscon-icst525";
+			reg = <0x1c 0x04>;
 			#clock-cells = <0>;
 			lock-offset = <0x14>;
 			vco-offset = <0x1c>;
@@ -241,13 +244,13 @@
 			clock-names = "apb_pclk";
 		};
 
-		uart@16000000 {
+		serial@16000000 {
 			compatible = "arm,pl011", "arm,primecell";
 			clocks = <&uartclk>, <&pclk>;
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart@17000000 {
+		serial@17000000 {
 			compatible = "arm,pl011", "arm,primecell";
 			clocks = <&uartclk>, <&pclk>;
 			clock-names = "uartclk", "apb_pclk";
diff --git a/arch/arm/boot/dts/mps2-an385.dts b/arch/arm/boot/dts/arm/mps2-an385.dts
index aebbebfc25d1..aebbebfc25d1 100644
--- a/arch/arm/boot/dts/mps2-an385.dts
+++ b/arch/arm/boot/dts/arm/mps2-an385.dts
diff --git a/arch/arm/boot/dts/mps2-an399.dts b/arch/arm/boot/dts/arm/mps2-an399.dts
index 349abf70b2a5..349abf70b2a5 100644
--- a/arch/arm/boot/dts/mps2-an399.dts
+++ b/arch/arm/boot/dts/arm/mps2-an399.dts
diff --git a/arch/arm/boot/dts/mps2.dtsi b/arch/arm/boot/dts/arm/mps2.dtsi
index 96fb5a5cf4d3..ce308820765b 100644
--- a/arch/arm/boot/dts/mps2.dtsi
+++ b/arch/arm/boot/dts/arm/mps2.dtsi
@@ -42,7 +42,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../armv7-m.dtsi"
 
 / {
 	#address-cells = <1>;
@@ -161,9 +161,11 @@
 			};
 
 			timer2: dual-timer@2000 {
-				compatible = "arm,sp804";
+				compatible = "arm,sp804", "arm,primecell";
 				reg = <0x2000 0x1000>;
-				clocks = <&sysclk>;
+				clocks = <&sysclk>, <&sysclk>, <&sysclk>;
+				clock-names = "timer0clk", "timer1clk",
+					       "apb_pclk";
 				interrupts = <10>;
 				status = "disabled";
 			};
@@ -197,8 +199,8 @@
 				arm,primecell-periphid = <0x00141805>;
 				reg = <0x8000 0x1000>;
 				interrupts = <0>;
-				clocks = <&sysclk>;
-				clock-names = "apb_pclk";
+				clocks = <&sysclk>, <&sysclk>;
+				clock-names = "wdog_clk", "apb_pclk";
 				status = "disabled";
 			};
 		};
@@ -214,8 +216,13 @@
 			compatible = "syscon", "simple-mfd";
 			reg = <0x8000 0x10>;
 
-			led0 {
+			ranges = <0x0 0x8000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			led@0,0 {
 				compatible = "register-bit-led";
+				reg = <0x00 0x04>;
 				offset = <0x0>;
 				mask = <0x01>;
 				label = "userled:0";
@@ -223,8 +230,9 @@
 				default-state = "on";
 			};
 
-			led1 {
+			led@0,1 {
 				compatible = "register-bit-led";
+				reg = <0x00 0x04>;
 				offset = <0x0>;
 				mask = <0x02>;
 				label = "userled:1";
diff --git a/arch/arm/boot/dts/versatile-ab-ib2.dts b/arch/arm/boot/dts/arm/versatile-ab-ib2.dts
index 5890cb974f78..7ebb0dfd0467 100644
--- a/arch/arm/boot/dts/versatile-ab-ib2.dts
+++ b/arch/arm/boot/dts/arm/versatile-ab-ib2.dts
@@ -10,12 +10,16 @@
 	model = "ARM Versatile AB + IB2 board";
 
 	/* Special IB2 control register */
-	ib2_syscon@27000000 {
+	syscon@27000000 {
 		compatible = "arm,versatile-ib2-syscon", "syscon", "simple-mfd";
 		reg = <0x27000000 0x4>;
+		ranges = <0x0 0x27000000 0x4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-		led@00.4 {
+		led@0,4 {
 			compatible = "register-bit-led";
+			reg = <0x00 0x04>;
 			offset = <0x00>;
 			mask = <0x10>;
 			label = "versatile-ib2:0";
diff --git a/arch/arm/boot/dts/versatile-ab.dts b/arch/arm/boot/dts/arm/versatile-ab.dts
index 37bd41ff8dff..f31dcf7e5862 100644
--- a/arch/arm/boot/dts/versatile-ab.dts
+++ b/arch/arm/boot/dts/arm/versatile-ab.dts
@@ -70,61 +70,72 @@
 	core-module@10000000 {
 		compatible = "arm,core-module-versatile", "syscon", "simple-mfd";
 		reg = <0x10000000 0x200>;
+		ranges = <0x0 0x10000000 0x200>;
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-		led@08.0 {
+		led@8,0 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x01>;
 			label = "versatile:0";
 			linux,default-trigger = "heartbeat";
 			default-state = "on";
 		};
-		led@08.1 {
+		led@8,1 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x02>;
 			label = "versatile:1";
 			linux,default-trigger = "mmc0";
 			default-state = "off";
 		};
-		led@08.2 {
+		led@8,2 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x04>;
 			label = "versatile:2";
 			linux,default-trigger = "cpu0";
 			default-state = "off";
 		};
-		led@08.3 {
+		led@8,3 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x08>;
 			label = "versatile:3";
 			default-state = "off";
 		};
-		led@08.4 {
+		led@8,4 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x10>;
 			label = "versatile:4";
 			default-state = "off";
 		};
-		led@08.5 {
+		led@8,5 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x20>;
 			label = "versatile:5";
 			default-state = "off";
 		};
-		led@08.6 {
+		led@8,6 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x40>;
 			label = "versatile:6";
 			default-state = "off";
 		};
-		led@08.7 {
+		led@8,7 {
 			compatible = "register-bit-led";
+			reg = <0x08 0x04>;
 			offset = <0x08>;
 			mask = <0x80>;
 			label = "versatile:7";
@@ -195,16 +206,15 @@
 		#size-cells = <1>;
 		ranges;
 
-		vic: intc@10140000 {
+		vic: interrupt-controller@10140000 {
 			compatible = "arm,versatile-vic";
 			interrupt-controller;
 			#interrupt-cells = <1>;
 			reg = <0x10140000 0x1000>;
-			clear-mask = <0xffffffff>;
 			valid-mask = <0xffffffff>;
 		};
 
-		sic: intc@10003000 {
+		sic: interrupt-controller@10003000 {
 			compatible = "arm,versatile-sic";
 			interrupt-controller;
 			#interrupt-cells = <1>;
@@ -227,7 +237,7 @@
 			clock-names = "apb_pclk";
 		};
 
-		uart0: uart@101f1000 {
+		uart0: serial@101f1000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f1000 0x1000>;
 			interrupts = <12>;
@@ -235,7 +245,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart1: uart@101f2000 {
+		uart1: serial@101f2000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f2000 0x1000>;
 			interrupts = <13>;
@@ -243,7 +253,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart2: uart@101f3000 {
+		uart2: serial@101f3000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f3000 0x1000>;
 			interrupts = <14>;
@@ -381,7 +391,7 @@
 			reg = <0x101f4000 0x1000>;
 			interrupts = <11>;
 			clocks = <&xtal24mhz>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		fpga {
diff --git a/arch/arm/boot/dts/versatile-pb.dts b/arch/arm/boot/dts/arm/versatile-pb.dts
index 06a0fdf24026..fc21ce54b33a 100644
--- a/arch/arm/boot/dts/versatile-pb.dts
+++ b/arch/arm/boot/dts/arm/versatile-pb.dts
@@ -7,7 +7,7 @@
 
 	amba {
 		/* The Versatile PB is using more SIC IRQ lines than the AB */
-		sic: intc@10003000 {
+		sic: interrupt-controller@10003000 {
 			clear-mask = <0xffffffff>;
 			/*
 			 * Valid interrupt lines mask according to
@@ -85,7 +85,7 @@
 				 */
 				interrupts-extended = <&sic 22 &sic 23>;
 			};
-			uart@9000 {
+			serial@9000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x9000 0x1000>;
 				interrupt-parent = <&sic>;
diff --git a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi b/arch/arm/boot/dts/arm/vexpress-v2m-rs1.dtsi
index dfae90adbb7c..8af4b77fe655 100644
--- a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
+++ b/arch/arm/boot/dts/arm/vexpress-v2m-rs1.dtsi
@@ -17,21 +17,155 @@
  * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
  * CHANGES TO vexpress-v2m.dtsi!
  */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
-	smb@8000000 {
-		motherboard {
-			model = "V2M-P1";
+	v2m_fixed_3v3: fixed-regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	v2m_clk24mhz: clk24mhz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "v2m:clk24mhz";
+	};
+
+	v2m_refclk1mhz: refclk1mhz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1000000>;
+		clock-output-names = "v2m:refclk1mhz";
+	};
+
+	v2m_refclk32khz: refclk32khz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "v2m:refclk32khz";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-1 {
+			label = "v2m:green:user1";
+			gpios = <&v2m_led_gpios 0 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			label = "v2m:green:user2";
+			gpios = <&v2m_led_gpios 1 0>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		led-3 {
+			label = "v2m:green:user3";
+			gpios = <&v2m_led_gpios 2 0>;
+			linux,default-trigger = "cpu0";
+		};
+
+		led-4 {
+			label = "v2m:green:user4";
+			gpios = <&v2m_led_gpios 3 0>;
+			linux,default-trigger = "cpu1";
+		};
+
+		led-5 {
+			label = "v2m:green:user5";
+			gpios = <&v2m_led_gpios 4 0>;
+			linux,default-trigger = "cpu2";
+		};
+
+		led-6 {
+			label = "v2m:green:user6";
+			gpios = <&v2m_led_gpios 5 0>;
+			linux,default-trigger = "cpu3";
+		};
+
+		led-7 {
+			label = "v2m:green:user7";
+			gpios = <&v2m_led_gpios 6 0>;
+			linux,default-trigger = "cpu4";
+		};
+
+		led-8 {
+			label = "v2m:green:user8";
+			gpios = <&v2m_led_gpios 7 0>;
+			linux,default-trigger = "cpu5";
+		};
+	};
+
+	bus@8000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 63>;
+		interrupt-map = <0  0 &gic GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,
+				<0  1 &gic GIC_SPI  1 IRQ_TYPE_LEVEL_HIGH>,
+				<0  2 &gic GIC_SPI  2 IRQ_TYPE_LEVEL_HIGH>,
+				<0  3 &gic GIC_SPI  3 IRQ_TYPE_LEVEL_HIGH>,
+				<0  4 &gic GIC_SPI  4 IRQ_TYPE_LEVEL_HIGH>,
+				<0  5 &gic GIC_SPI  5 IRQ_TYPE_LEVEL_HIGH>,
+				<0  6 &gic GIC_SPI  6 IRQ_TYPE_LEVEL_HIGH>,
+				<0  7 &gic GIC_SPI  7 IRQ_TYPE_LEVEL_HIGH>,
+				<0  8 &gic GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+				<0  9 &gic GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+				<0 10 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				<0 11 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				<0 12 &gic GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				<0 13 &gic GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				<0 14 &gic GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				<0 15 &gic GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				<0 16 &gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				<0 17 &gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				<0 18 &gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				<0 19 &gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				<0 20 &gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				<0 21 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				<0 22 &gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				<0 23 &gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+				<0 24 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				<0 25 &gic GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				<0 26 &gic GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				<0 27 &gic GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				<0 28 &gic GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				<0 29 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				<0 30 &gic GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				<0 31 &gic GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				<0 32 &gic GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				<0 33 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				<0 34 &gic GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				<0 35 &gic GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+				<0 36 &gic GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				<0 37 &gic GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				<0 38 &gic GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+				<0 39 &gic GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				<0 40 &gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				<0 41 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				<0 42 &gic GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+
+		motherboard-bus@8000000 {
 			arm,hbi = <0x190>;
 			arm,vexpress,site = <0>;
-			arm,v2m-memory-map = "rs1";
 			compatible = "arm,vexpress,v2m-p1", "simple-bus";
 			#address-cells = <2>; /* SMB chipselect number and offset */
 			#size-cells = <1>;
-			#interrupt-cells = <1>;
-			ranges;
-
-			nor_flash: flash@0,00000000 {
+			ranges = <0 0 0x08000000 0x04000000>,
+				 <1 0 0x14000000 0x04000000>,
+				 <2 0 0x18000000 0x04000000>,
+				 <3 0 0x1c000000 0x04000000>,
+				 <4 0 0x0c000000 0x04000000>,
+				 <5 0 0x10000000 0x04000000>;
+
+			nor_flash: flash@0 {
 				compatible = "arm,vexpress-flash", "cfi-flash";
 				reg = <0 0x00000000 0x04000000>,
 				      <4 0x00000000 0x04000000>;
@@ -41,13 +175,13 @@
 				};
 			};
 
-			psram@1,00000000 {
+			psram@100000000 {
 				compatible = "arm,vexpress-psram", "mtd-ram";
 				reg = <1 0x00000000 0x02000000>;
 				bank-width = <4>;
 			};
 
-			ethernet@2,02000000 {
+			ethernet@202000000 {
 				compatible = "smsc,lan9118", "smsc,lan9115";
 				reg = <2 0x02000000 0x10000>;
 				interrupts = <15>;
@@ -59,14 +193,14 @@
 				vddvario-supply = <&v2m_fixed_3v3>;
 			};
 
-			usb@2,03000000 {
+			usb@203000000 {
 				compatible = "nxp,usb-isp1761";
 				reg = <2 0x03000000 0x20000>;
 				interrupts = <16>;
-				port1-otg;
+				dr_mode = "peripheral";
 			};
 
-			iofpga@3,00000000 {
+			iofpga-bus@300000000 {
 				compatible = "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -134,7 +268,7 @@
 					clock-names = "apb_pclk";
 				};
 
-				mmci@50000 {
+				mmc@50000 {
 					compatible = "arm,pl180", "arm,primecell";
 					reg = <0x050000 0x1000>;
 					interrupts = <9>, <10>;
@@ -162,7 +296,7 @@
 					clock-names = "KMIREFCLK", "apb_pclk";
 				};
 
-				v2m_serial0: uart@90000 {
+				v2m_serial0: serial@90000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x090000 0x1000>;
 					interrupts = <5>;
@@ -170,7 +304,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial1: uart@a0000 {
+				v2m_serial1: serial@a0000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0a0000 0x1000>;
 					interrupts = <6>;
@@ -178,7 +312,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial2: uart@b0000 {
+				v2m_serial2: serial@b0000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0b0000 0x1000>;
 					interrupts = <7>;
@@ -186,7 +320,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial3: uart@c0000 {
+				v2m_serial3: serial@c0000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0c0000 0x1000>;
 					interrupts = <8>;
@@ -194,12 +328,12 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				wdt@f0000 {
+				watchdog@f0000 {
 					compatible = "arm,sp805", "arm,primecell";
 					reg = <0x0f0000 0x1000>;
 					interrupts = <0>;
 					clocks = <&v2m_refclk32khz>, <&smbclk>;
-					clock-names = "wdogclk", "apb_pclk";
+					clock-names = "wdog_clk", "apb_pclk";
 				};
 
 				v2m_timer01: timer@110000 {
@@ -281,159 +415,78 @@
 						};
 					};
 				};
-			};
-
-			v2m_fixed_3v3: fixed-regulator-0 {
-				compatible = "regulator-fixed";
-				regulator-name = "3V3";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			v2m_clk24mhz: clk24mhz {
-				compatible = "fixed-clock";
-				#clock-cells = <0>;
-				clock-frequency = <24000000>;
-				clock-output-names = "v2m:clk24mhz";
-			};
-
-			v2m_refclk1mhz: refclk1mhz {
-				compatible = "fixed-clock";
-				#clock-cells = <0>;
-				clock-frequency = <1000000>;
-				clock-output-names = "v2m:refclk1mhz";
-			};
-
-			v2m_refclk32khz: refclk32khz {
-				compatible = "fixed-clock";
-				#clock-cells = <0>;
-				clock-frequency = <32768>;
-				clock-output-names = "v2m:refclk32khz";
-			};
-
-			leds {
-				compatible = "gpio-leds";
-
-				user1 {
-					label = "v2m:green:user1";
-					gpios = <&v2m_led_gpios 0 0>;
-					linux,default-trigger = "heartbeat";
-				};
-
-				user2 {
-					label = "v2m:green:user2";
-					gpios = <&v2m_led_gpios 1 0>;
-					linux,default-trigger = "mmc0";
-				};
-
-				user3 {
-					label = "v2m:green:user3";
-					gpios = <&v2m_led_gpios 2 0>;
-					linux,default-trigger = "cpu0";
-				};
-
-				user4 {
-					label = "v2m:green:user4";
-					gpios = <&v2m_led_gpios 3 0>;
-					linux,default-trigger = "cpu1";
-				};
 
-				user5 {
-					label = "v2m:green:user5";
-					gpios = <&v2m_led_gpios 4 0>;
-					linux,default-trigger = "cpu2";
-				};
-
-				user6 {
-					label = "v2m:green:user6";
-					gpios = <&v2m_led_gpios 5 0>;
-					linux,default-trigger = "cpu3";
-				};
-
-				user7 {
-					label = "v2m:green:user7";
-					gpios = <&v2m_led_gpios 6 0>;
-					linux,default-trigger = "cpu4";
-				};
+				mcc {
+					compatible = "arm,vexpress,config-bus";
+					arm,vexpress,config-bridge = <&v2m_sysreg>;
 
-				user8 {
-					label = "v2m:green:user8";
-					gpios = <&v2m_led_gpios 7 0>;
-					linux,default-trigger = "cpu5";
-				};
-			};
-
-			mcc {
-				compatible = "arm,vexpress,config-bus";
-				arm,vexpress,config-bridge = <&v2m_sysreg>;
-
-				oscclk0 {
-					/* MCC static memory clock */
-					compatible = "arm,vexpress-osc";
-					arm,vexpress-sysreg,func = <1 0>;
-					freq-range = <25000000 60000000>;
-					#clock-cells = <0>;
-					clock-output-names = "v2m:oscclk0";
-				};
+					oscclk0 {
+						/* MCC static memory clock */
+						compatible = "arm,vexpress-osc";
+						arm,vexpress-sysreg,func = <1 0>;
+						freq-range = <25000000 60000000>;
+						#clock-cells = <0>;
+						clock-output-names = "v2m:oscclk0";
+					};
 
-				v2m_oscclk1: oscclk1 {
-					/* CLCD clock */
-					compatible = "arm,vexpress-osc";
-					arm,vexpress-sysreg,func = <1 1>;
-					freq-range = <23750000 65000000>;
-					#clock-cells = <0>;
-					clock-output-names = "v2m:oscclk1";
-				};
+					v2m_oscclk1: oscclk1 {
+						/* CLCD clock */
+						compatible = "arm,vexpress-osc";
+						arm,vexpress-sysreg,func = <1 1>;
+						freq-range = <23750000 65000000>;
+						#clock-cells = <0>;
+						clock-output-names = "v2m:oscclk1";
+					};
 
-				v2m_oscclk2: oscclk2 {
-					/* IO FPGA peripheral clock */
-					compatible = "arm,vexpress-osc";
-					arm,vexpress-sysreg,func = <1 2>;
-					freq-range = <24000000 24000000>;
-					#clock-cells = <0>;
-					clock-output-names = "v2m:oscclk2";
-				};
+					v2m_oscclk2: oscclk2 {
+						/* IO FPGA peripheral clock */
+						compatible = "arm,vexpress-osc";
+						arm,vexpress-sysreg,func = <1 2>;
+						freq-range = <24000000 24000000>;
+						#clock-cells = <0>;
+						clock-output-names = "v2m:oscclk2";
+					};
 
-				volt-vio {
-					/* Logic level voltage */
-					compatible = "arm,vexpress-volt";
-					arm,vexpress-sysreg,func = <2 0>;
-					regulator-name = "VIO";
-					regulator-always-on;
-					label = "VIO";
-				};
+					volt-vio {
+						/* Logic level voltage */
+						compatible = "arm,vexpress-volt";
+						arm,vexpress-sysreg,func = <2 0>;
+						regulator-name = "VIO";
+						regulator-always-on;
+						label = "VIO";
+					};
 
-				temp-mcc {
-					/* MCC internal operating temperature */
-					compatible = "arm,vexpress-temp";
-					arm,vexpress-sysreg,func = <4 0>;
-					label = "MCC";
-				};
+					temp-mcc {
+						/* MCC internal operating temperature */
+						compatible = "arm,vexpress-temp";
+						arm,vexpress-sysreg,func = <4 0>;
+						label = "MCC";
+					};
 
-				reset {
-					compatible = "arm,vexpress-reset";
-					arm,vexpress-sysreg,func = <5 0>;
-				};
+					reset {
+						compatible = "arm,vexpress-reset";
+						arm,vexpress-sysreg,func = <5 0>;
+					};
 
-				muxfpga {
-					compatible = "arm,vexpress-muxfpga";
-					arm,vexpress-sysreg,func = <7 0>;
-				};
+					muxfpga {
+						compatible = "arm,vexpress-muxfpga";
+						arm,vexpress-sysreg,func = <7 0>;
+					};
 
-				shutdown {
-					compatible = "arm,vexpress-shutdown";
-					arm,vexpress-sysreg,func = <8 0>;
-				};
+					shutdown {
+						compatible = "arm,vexpress-shutdown";
+						arm,vexpress-sysreg,func = <8 0>;
+					};
 
-				reboot {
-					compatible = "arm,vexpress-reboot";
-					arm,vexpress-sysreg,func = <9 0>;
-				};
+					reboot {
+						compatible = "arm,vexpress-reboot";
+						arm,vexpress-sysreg,func = <9 0>;
+					};
 
-				dvimode {
-					compatible = "arm,vexpress-dvimode";
-					arm,vexpress-sysreg,func = <11 0>;
+					dvimode {
+						compatible = "arm,vexpress-dvimode";
+						arm,vexpress-sysreg,func = <11 0>;
+					};
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/arm/vexpress-v2m.dtsi
index 2e29d7790497..c5e92f6d2fcd 100644
--- a/arch/arm/boot/dts/vexpress-v2m.dtsi
+++ b/arch/arm/boot/dts/arm/vexpress-v2m.dtsi
@@ -17,18 +17,73 @@
  * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
  * CHANGES TO vexpress-v2m-rs1.dtsi!
  */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
-	smb@4000000 {
-		motherboard {
-			model = "V2M-P1";
+	bus@40000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x40000000 0x40000000 0x10000000>,
+			 <0x10000000 0x10000000 0x00020000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 63>;
+		interrupt-map = <0  0 &gic GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,
+				<0  1 &gic GIC_SPI  1 IRQ_TYPE_LEVEL_HIGH>,
+				<0  2 &gic GIC_SPI  2 IRQ_TYPE_LEVEL_HIGH>,
+				<0  3 &gic GIC_SPI  3 IRQ_TYPE_LEVEL_HIGH>,
+				<0  4 &gic GIC_SPI  4 IRQ_TYPE_LEVEL_HIGH>,
+				<0  5 &gic GIC_SPI  5 IRQ_TYPE_LEVEL_HIGH>,
+				<0  6 &gic GIC_SPI  6 IRQ_TYPE_LEVEL_HIGH>,
+				<0  7 &gic GIC_SPI  7 IRQ_TYPE_LEVEL_HIGH>,
+				<0  8 &gic GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+				<0  9 &gic GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+				<0 10 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				<0 11 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				<0 12 &gic GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				<0 13 &gic GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				<0 14 &gic GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				<0 15 &gic GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				<0 16 &gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				<0 17 &gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				<0 18 &gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				<0 19 &gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				<0 20 &gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				<0 21 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				<0 22 &gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				<0 23 &gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+				<0 24 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				<0 25 &gic GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				<0 26 &gic GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				<0 27 &gic GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				<0 28 &gic GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				<0 29 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				<0 30 &gic GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				<0 31 &gic GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				<0 32 &gic GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				<0 33 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				<0 34 &gic GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				<0 35 &gic GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+				<0 36 &gic GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				<0 37 &gic GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				<0 38 &gic GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+				<0 39 &gic GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				<0 40 &gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				<0 41 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				<0 42 &gic GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+
+		motherboard-bus@40000000 {
 			arm,hbi = <0x190>;
 			arm,vexpress,site = <0>;
 			compatible = "arm,vexpress,v2m-p1", "simple-bus";
 			#address-cells = <2>; /* SMB chipselect number and offset */
 			#size-cells = <1>;
-			#interrupt-cells = <1>;
-			ranges;
+			ranges = <0 0 0x40000000 0x04000000>,
+				 <1 0 0x44000000 0x04000000>,
+				 <2 0 0x48000000 0x04000000>,
+				 <3 0 0x4c000000 0x04000000>,
+				 <7 0 0x10000000 0x00020000>;
 
 			flash@0,00000000 {
 				compatible = "arm,vexpress-flash", "cfi-flash";
@@ -62,7 +117,7 @@
 				compatible = "nxp,usb-isp1761";
 				reg = <3 0x03000000 0x20000>;
 				interrupts = <16>;
-				port1-otg;
+				dr_mode = "peripheral";
 			};
 
 			iofpga@7,00000000 {
@@ -161,7 +216,7 @@
 					clock-names = "KMIREFCLK", "apb_pclk";
 				};
 
-				v2m_serial0: uart@9000 {
+				v2m_serial0: serial@9000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x09000 0x1000>;
 					interrupts = <5>;
@@ -169,7 +224,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial1: uart@a000 {
+				v2m_serial1: serial@a000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0a000 0x1000>;
 					interrupts = <6>;
@@ -177,7 +232,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial2: uart@b000 {
+				v2m_serial2: serial@b000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0b000 0x1000>;
 					interrupts = <7>;
@@ -185,7 +240,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial3: uart@c000 {
+				v2m_serial3: serial@c000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0c000 0x1000>;
 					interrupts = <8>;
@@ -198,7 +253,7 @@
 					reg = <0x0f000 0x1000>;
 					interrupts = <0>;
 					clocks = <&v2m_refclk32khz>, <&smbclk>;
-					clock-names = "wdogclk", "apb_pclk";
+					clock-names = "wdog_clk", "apb_pclk";
 				};
 
 				v2m_timer01: timer@11000 {
@@ -328,49 +383,49 @@
 			leds {
 				compatible = "gpio-leds";
 
-				user1 {
+				led-user1 {
 					label = "v2m:green:user1";
 					gpios = <&v2m_led_gpios 0 0>;
 					linux,default-trigger = "heartbeat";
 				};
 
-				user2 {
+				led-user2 {
 					label = "v2m:green:user2";
 					gpios = <&v2m_led_gpios 1 0>;
 					linux,default-trigger = "mmc0";
 				};
 
-				user3 {
+				led-user3 {
 					label = "v2m:green:user3";
 					gpios = <&v2m_led_gpios 2 0>;
 					linux,default-trigger = "cpu0";
 				};
 
-				user4 {
+				led-user4 {
 					label = "v2m:green:user4";
 					gpios = <&v2m_led_gpios 3 0>;
 					linux,default-trigger = "cpu1";
 				};
 
-				user5 {
+				led-user5 {
 					label = "v2m:green:user5";
 					gpios = <&v2m_led_gpios 4 0>;
 					linux,default-trigger = "cpu2";
 				};
 
-				user6 {
+				led-user6 {
 					label = "v2m:green:user6";
 					gpios = <&v2m_led_gpios 5 0>;
 					linux,default-trigger = "cpu3";
 				};
 
-				user7 {
+				led-user7 {
 					label = "v2m:green:user7";
 					gpios = <&v2m_led_gpios 6 0>;
 					linux,default-trigger = "cpu4";
 				};
 
-				user8 {
+				led-user8 {
 					label = "v2m:green:user8";
 					gpios = <&v2m_led_gpios 7 0>;
 					linux,default-trigger = "cpu5";
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca15-tc1.dts
index 0dc4277d5f8b..679537e17ff5 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca15-tc1.dts
@@ -87,8 +87,8 @@
 		status = "disabled";
 		reg = <0 0x2b060000 0 0x1000>;
 		interrupts = <0 98 4>;
-		clocks = <&sys_pll>;
-		clock-names = "apb_pclk";
+		clocks = <&sys_pll>, <&sys_pll>;
+		clock-names = "wdog_clk", "apb_pclk";
 	};
 
 	gic: interrupt-controller@2c001000 {
@@ -236,63 +236,8 @@
 		};
 	};
 
-	smb@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
+	bus@8000000 {
+		ranges = <0x8000000 0 0x8000000 0x18000000>;
 	};
 
 	site2: hsb@40000000 {
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca15_a7.dts
index 1de0a658adf1..511e87cc2bc5 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca15_a7.dts
@@ -128,7 +128,7 @@
 		reg = <0 0x2a490000 0 0x1000>;
 		interrupts = <0 98 4>;
 		clocks = <&oscclk6a>, <&oscclk6a>;
-		clock-names = "wdogclk", "apb_pclk";
+		clock-names = "wdog_clk", "apb_pclk";
 	};
 
 	hdlcd@2b000000 {
@@ -608,63 +608,8 @@
 		};
 	};
 
-	smb: smb@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
+	smb: bus@8000000 {
+		ranges = <0x8000000 0 0x8000000 0x18000000>;
 	};
 
 	site2: hsb@40000000 {
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca5s.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca5s.dts
index d5b47d526f9e..ff1f9a1bcfcf 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca5s.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca5s.dts
@@ -132,6 +132,7 @@
 		reg = <0x2c0f0000 0x1000>;
 		interrupts = <0 84 4>;
 		cache-level = <2>;
+		cache-unified;
 	};
 
 	pmu {
@@ -206,63 +207,8 @@
 		};
 	};
 
-	smb: smb@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x04000000>,
-			 <1 0 0x14000000 0x04000000>,
-			 <2 0 0x18000000 0x04000000>,
-			 <3 0 0x1c000000 0x04000000>,
-			 <4 0 0x0c000000 0x04000000>,
-			 <5 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
+	smb: bus@8000000 {
+		ranges = <0 0x8000000 0x18000000>;
 	};
 
 	site2: hsb@40000000 {
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca9.dts
index d796efaadbe3..5916e4877eac 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca9.dts
@@ -122,8 +122,8 @@
 		reg = <0x100e4000 0x1000>;
 		interrupts = <0 48 4>,
 			     <0 49 4>;
-		clocks = <&oscclk2>, <&oscclk2>;
-		clock-names = "timclk", "apb_pclk";
+		clocks = <&oscclk2>, <&oscclk2>, <&oscclk2>;
+		clock-names = "timer0clk", "timer1clk", "apb_pclk";
 		status = "disabled";
 	};
 
@@ -132,7 +132,7 @@
 		reg = <0x100e5000 0x1000>;
 		interrupts = <0 51 4>;
 		clocks = <&oscclk2>, <&oscclk2>;
-		clock-names = "wdogclk", "apb_pclk";
+		clock-names = "wdog_clk", "apb_pclk";
 	};
 
 	scu@1e000000 {
@@ -295,64 +295,6 @@
 		};
 	};
 
-	smb: smb@4000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x40000000 0x04000000>,
-			 <1 0 0x44000000 0x04000000>,
-			 <2 0 0x48000000 0x04000000>,
-			 <3 0 0x4c000000 0x04000000>,
-			 <7 0 0x10000000 0x00020000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
-	};
-
 	site2: hsb@e0000000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/armada-385-turris-omnia.dts b/arch/arm/boot/dts/armada-385-turris-omnia.dts
deleted file mode 100644
index 768b6c5d2129..000000000000
--- a/arch/arm/boot/dts/armada-385-turris-omnia.dts
+++ /dev/null
@@ -1,359 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Device Tree file for the Turris Omnia
- *
- * Copyright (C) 2016 Uwe Kleine-König <uwe@kleine-koenig.org>
- * Copyright (C) 2016 Tomas Hlavacek <tmshlvkc@gmail.com>
- *
- * Schematic available at https://www.turris.cz/doc/_media/rtrom01-schema.pdf
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include "armada-385.dtsi"
-
-/ {
-	model = "Turris Omnia";
-	compatible = "cznic,turris-omnia", "marvell,armada385", "marvell,armada380";
-
-	chosen {
-		stdout-path = &uart0;
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x40000000>; /* 1024 MB */
-	};
-
-	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
-			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
-			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
-			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
-
-		internal-regs {
-
-			/* USB part of the PCIe2/USB 2.0 port */
-			usb@58000 {
-				status = "okay";
-			};
-
-			sata@a8000 {
-				status = "okay";
-			};
-
-			sdhci@d8000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdhci_pins>;
-				status = "okay";
-
-				bus-width = <8>;
-				no-1-8-v;
-				non-removable;
-			};
-
-			usb3@f0000 {
-				status = "okay";
-			};
-
-			usb3@f8000 {
-				status = "okay";
-			};
-		};
-
-		pcie {
-			status = "okay";
-
-			pcie@1,0 {
-				/* Port 0, Lane 0 */
-				status = "okay";
-			};
-
-			pcie@2,0 {
-				/* Port 1, Lane 0 */
-				status = "okay";
-			};
-
-			pcie@3,0 {
-				/* Port 2, Lane 0 */
-				status = "okay";
-			};
-		};
-	};
-};
-
-/* Connected to 88E6176 switch, port 6 */
-&eth0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ge0_rgmii_pins>;
-	status = "okay";
-	phy-mode = "rgmii";
-
-	fixed-link {
-		speed = <1000>;
-		full-duplex;
-	};
-};
-
-/* Connected to 88E6176 switch, port 5 */
-&eth1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ge1_rgmii_pins>;
-	status = "okay";
-	phy-mode = "rgmii";
-
-	fixed-link {
-		speed = <1000>;
-		full-duplex;
-	};
-};
-
-/* WAN port */
-&eth2 {
-	status = "okay";
-	phy-mode = "sgmii";
-	phy = <&phy1>;
-};
-
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
-	status = "okay";
-
-	i2cmux@70 {
-		compatible = "nxp,pca9547";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		status = "okay";
-
-		i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			/* STM32F0 command interface at address 0x2a */
-			/* leds device (in STM32F0) at address 0x2b */
-
-			eeprom@54 {
-				compatible = "atmel,24c64";
-				reg = <0x54>;
-
-				/* The EEPROM contains data for bootloader.
-				 * Contents:
-				 * 	struct omnia_eeprom {
-				 * 		u32 magic; (=0x0341a034 in LE)
-				 *		u32 ramsize; (in GiB)
-				 * 		char regdomain[4];
-				 * 		u32 crc32;
-				 * 	};
-				 */
-			};
-		};
-
-		i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			/* routed to PCIe0/mSATA connector (CN7A) */
-		};
-
-		i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-
-			/* routed to PCIe1/USB2 connector (CN61A) */
-		};
-
-		i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-
-			/* routed to PCIe2 connector (CN62A) */
-		};
-
-		i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-
-			/* routed to SFP+ */
-		};
-
-		i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-
-			/* ATSHA204A at address 0x64 */
-		};
-
-		i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-
-			/* exposed on pin header */
-		};
-
-		i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-
-			pcawan: gpio@71 {
-				/*
-				 * GPIO expander for SFP+ signals and
-				 * and phy irq
-				 */
-				compatible = "nxp,pca9538";
-				reg = <0x71>;
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&pcawan_pins>;
-
-				interrupt-parent = <&gpio1>;
-				interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
-
-				gpio-controller;
-				#gpio-cells = <2>;
-			};
-		};
-	};
-};
-
-&mdio {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mdio_pins>;
-	status = "okay";
-
-	phy1: phy@1 {
-		status = "okay";
-		compatible = "ethernet-phy-id0141.0DD1", "ethernet-phy-ieee802.3-c22";
-		reg = <1>;
-
-		/* irq is connected to &pcawan pin 7 */
-	};
-
-	/* Switch MV88E6176 at address 0x10 */
-	switch@10 {
-		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		dsa,member = <0 0>;
-
-		reg = <0x10>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ports@0 {
-				reg = <0>;
-				label = "lan0";
-			};
-
-			ports@1 {
-				reg = <1>;
-				label = "lan1";
-			};
-
-			ports@2 {
-				reg = <2>;
-				label = "lan2";
-			};
-
-			ports@3 {
-				reg = <3>;
-				label = "lan3";
-			};
-
-			ports@4 {
-				reg = <4>;
-				label = "lan4";
-			};
-
-			ports@5 {
-				reg = <5>;
-				label = "cpu";
-				ethernet = <&eth1>;
-				phy-mode = "rgmii-id";
-
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-
-			/* port 6 is connected to eth0 */
-		};
-	};
-};
-
-&pinctrl {
-	pcawan_pins: pcawan-pins {
-		marvell,pins = "mpp46";
-		marvell,function = "gpio";
-	};
-
-	spi0cs0_pins: spi0cs0-pins {
-		marvell,pins = "mpp25";
-		marvell,function = "spi0";
-	};
-
-	spi0cs1_pins: spi0cs1-pins {
-		marvell,pins = "mpp26";
-		marvell,function = "spi0";
-	};
-};
-
-&spi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi0_pins &spi0cs0_pins>;
-	status = "okay";
-
-	spi-nor@0 {
-		compatible = "spansion,s25fl164k", "jedec,spi-nor";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		reg = <0>;
-		spi-max-frequency = <40000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				reg = <0x0 0x00100000>;
-				label = "U-Boot";
-			};
-
-			partition@100000 {
-				reg = <0x00100000 0x00700000>;
-				label = "Rescue system";
-			};
-		};
-	};
-
-	/* MISO, MOSI, SCLK and CS1 are routed to pin header CN11 */
-};
-
-&uart0 {
-	/* Pin header CN10 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins>;
-	status = "okay";
-};
-
-&uart1 {
-	/* Pin header CN11 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
deleted file mode 100644
index 4afa8662c4e8..000000000000
--- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
+++ /dev/null
@@ -1,215 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-// Copyright 2019 IBM Corp.
-
-/dts-v1/;
-
-#include "aspeed-g6.dtsi"
-
-/ {
-	model = "AST2600 EVB";
-	compatible = "aspeed,ast2600";
-
-	aliases {
-		serial4 = &uart5;
-	};
-
-	chosen {
-		bootargs = "console=ttyS4,115200n8";
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x80000000>;
-	};
-};
-
-&mdio1 {
-	status = "okay";
-
-	ethphy1: ethernet-phy@0 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&mdio2 {
-	status = "okay";
-
-	ethphy2: ethernet-phy@0 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&mdio3 {
-	status = "okay";
-
-	ethphy3: ethernet-phy@0 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&mac1 {
-	status = "okay";
-
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy1>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii2_default>;
-};
-
-&mac2 {
-	status = "okay";
-
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy2>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii3_default>;
-};
-
-&mac3 {
-	status = "okay";
-
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy3>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii4_default>;
-};
-
-&emmc_controller {
-	status = "okay";
-};
-
-&emmc {
-	non-removable;
-	bus-width = <4>;
-	max-frequency = <52000000>;
-};
-
-&rtc {
-	status = "okay";
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-		spi-max-frequency = <50000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			u-boot@0 {
-				reg = <0x0 0xe0000>; // 896KB
-				label = "u-boot";
-			};
-
-			u-boot-env@e0000 {
-				reg = <0xe0000 0x20000>; // 128KB
-				label = "u-boot-env";
-			};
-
-			kernel@100000 {
-				reg = <0x100000 0x900000>; // 9MB
-				label = "kernel";
-			};
-
-			rofs@a00000 {
-				reg = <0xa00000 0x2000000>; // 32MB
-				label = "rofs";
-			};
-
-			rwfs@6000000 {
-				reg = <0x2a00000 0x1600000>; // 22MB
-				label = "rwfs";
-			};
-		};
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "pnor";
-		spi-max-frequency = <100000000>;
-	};
-};
-
-&uart5 {
-	// Workaround for A0
-	compatible = "snps,dw-apb-uart";
-};
-
-&i2c0 {
-	status = "okay";
-
-	temp@2e {
-		compatible = "adi,adt7490";
-		reg = <0x2e>;
-	};
-};
-
-&i2c1 {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-};
-
-&i2c5 {
-	status = "okay";
-};
-
-&i2c6 {
-	status = "okay";
-};
-
-&i2c7 {
-	status = "okay";
-};
-
-&i2c8 {
-	status = "okay";
-};
-
-&i2c9 {
-	status = "okay";
-};
-
-&i2c12 {
-	status = "okay";
-};
-
-&i2c13 {
-	status = "okay";
-};
-
-&i2c14 {
-	status = "okay";
-};
-
-&i2c15 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts b/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts
deleted file mode 100644
index c2ece0b91885..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts
+++ /dev/null
@@ -1,225 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/dts-v1/;
-
-#include "aspeed-g5.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-
-/ {
-	model = "Qualcomm Centriq 2400  REP AST2520";
-	compatible = "qualcomm,centriq2400-rep-bmc", "aspeed,ast2500";
-
-	chosen {
-		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
-	};
-
-	memory@80000000 {
-		reg = <0x80000000 0x40000000>;
-	};
-
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
-                        <&adc 4>, <&adc 5>, <&adc 6>, <&adc 8>;
-	};
-
-	iio-hwmon-battery {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 7>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		uid_led {
-			label = "UID_LED";
-			gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-		};
-
-		ras_error_led {
-			label = "RAS_ERROR_LED";
-			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
-		};
-
-		system_fault {
-			label = "System_fault";
-			gpios = <&gpio ASPEED_GPIO(A, 1) GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-#include "openbmc-flash-layout.dtsi"
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-	flash@0 {
-		status = "okay";
-	};
-};
-
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi2ck_default
-			&pinctrl_spi2miso_default
-			&pinctrl_spi2mosi_default
-			&pinctrl_spi2cs0_default>;
-};
-
-&uart3 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd3_default &pinctrl_rxd3_default>;
-	current-speed = <115200>;
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&mac0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
-};
-
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-
-	tmp421@1e {
-		compatible = "ti,tmp421";
-		reg = <0x1e>;
-	};
-	tmp421@2a {
-		compatible = "ti,tmp421";
-		reg = <0x2a>;
-	};
-	tmp421@4e {
-		compatible = "ti,tmp421";
-		reg = <0x4e>;
-	};
-	tmp421@1c {
-		compatible = "ti,tmp421";
-		reg = <0x1c>;
-	};
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-};
-
-&i2c5 {
-	status = "okay";
-};
-
-&i2c6 {
-	status = "okay";
-
-	tmp421@1d {
-		compatible = "ti,tmp421";
-		reg = <0x1d>;
-	};
-	tmp421@1f {
-		compatible = "ti,tmp421";
-		reg = <0x1f>;
-	};
-	tmp421@4d {
-		compatible = "ti,tmp421";
-		reg = <0x4d>;
-	};
-	tmp421@4f {
-		compatible = "ti,tmp421";
-		reg = <0x4f>;
-	};
-	nvt210@4c {
-		compatible = "nvt210";
-		reg = <0x4c>;
-	};
-	eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-		pagesize = <128>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
-};
-
-&i2c8 {
-	status = "okay";
-
-	pca9641@70 {
-		compatible = "nxp,pca9641";
-		reg = <0x70>;
-		i2c-arb {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			tmp421@1d {
-				compatible = "tmp421";
-				reg = <0x1d>;
-			};
-			adm1278@12 {
-				compatible = "adi,adm1278";
-				reg = <0x12>;
-				Rsense = <500>;
-			};
-			eeprom@50 {
-				compatible = "atmel,24c02";
-				reg = <0x50>;
-			};
-			ds1100@58 {
-				compatible = "ds1100";
-				reg = <0x58>;
-			};
-		};
-	};
-};
-
-&i2c9 {
-	status = "okay";
-};
-
-&vuart {
-	status = "okay";
-};
-
-&gfx {
-	status = "okay";
-};
-
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
-&gpio {
-	pin_gpio_c7 {
-		gpio-hog;
-		gpios = <ASPEED_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
-		output;
-		line-name = "BIOS_SPI_MUX_S";
-	};
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-cmm.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-cmm.dts
deleted file mode 100644
index 016bbcb99bb6..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-cmm.dts
+++ /dev/null
@@ -1,348 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-// Copyright (c) 2018 Facebook Inc.
-/dts-v1/;
-
-#include "ast2500-facebook-netbmc-common.dtsi"
-
-/ {
-	model = "Facebook Backpack CMM BMC";
-	compatible = "facebook,cmm-bmc", "aspeed,ast2500";
-
-	aliases {
-		/*
-		 * Override the default uart aliases to avoid breaking
-		 * the legacy applications.
-		 */
-		serial0 = &uart5;
-		serial1 = &uart1;
-		serial2 = &uart3;
-		serial3 = &uart4;
-
-		/*
-		 * Hardcode the bus number of i2c switches' channels to
-		 * avoid breaking the legacy applications.
-		 */
-		i2c16 = &imux16;
-		i2c17 = &imux17;
-		i2c18 = &imux18;
-		i2c19 = &imux19;
-		i2c20 = &imux20;
-		i2c21 = &imux21;
-		i2c22 = &imux22;
-		i2c23 = &imux23;
-		i2c24 = &imux24;
-		i2c25 = &imux25;
-		i2c26 = &imux26;
-		i2c27 = &imux27;
-		i2c28 = &imux28;
-		i2c29 = &imux29;
-		i2c30 = &imux30;
-		i2c31 = &imux31;
-		i2c32 = &imux32;
-		i2c33 = &imux33;
-		i2c34 = &imux34;
-		i2c35 = &imux35;
-		i2c36 = &imux36;
-		i2c37 = &imux37;
-		i2c38 = &imux38;
-		i2c39 = &imux39;
-	};
-
-	chosen {
-		stdout-path = &uart1;
-		bootargs = "console=ttyS1,9600n8 root=/dev/ram rw earlyprintk";
-	};
-
-	ast-adc-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
-			      <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>;
-	};
-};
-
-&uart1 {
-	pinctrl-0 = <&pinctrl_txd1_default
-		     &pinctrl_rxd1_default
-		     &pinctrl_ncts1_default
-		     &pinctrl_ndcd1_default
-		     &pinctrl_ndsr1_default
-		     &pinctrl_ndtr1_default
-		     &pinctrl_nrts1_default>;
-};
-
-&uart3 {
-	pinctrl-0 = <&pinctrl_txd3_default
-		     &pinctrl_rxd3_default
-		     &pinctrl_ncts3_default
-		     &pinctrl_ndcd3_default
-		     &pinctrl_nri3_default>;
-};
-
-&uart4 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd4_default
-		     &pinctrl_rxd4_default>;
-};
-
-/*
- * I2C bus reserved for communication with COM-E.
- */
-&i2c0 {
-	status = "okay";
-};
-
-/*
- * I2C bus to Line Cards and Fabric Cards.
- */
-&i2c1 {
-	status = "okay";
-
-	i2c-switch@77 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x77>;
-
-		imux16: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux17: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux18: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux19: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux20: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux21: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux22: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux23: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-/*
- * I2C bus to Power Distribution Board.
- */
-&i2c2 {
-	status = "okay";
-
-	i2c-switch@71 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x71>;
-
-		imux24: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux25: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux26: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux27: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux28: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux29: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux30: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux31: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-/*
- * I2c bus connected with temperature sensors on CMM.
- */
-&i2c3 {
-	status = "okay";
-};
-
-/*
- * I2C bus reserved for communication with COM-E.
- */
-&i2c4 {
-	status = "okay";
-};
-
-/*
- * I2c bus connected with ADM1278.
- */
-&i2c5 {
-	status = "okay";
-};
-
-/*
- * I2c bus connected with I/O Expander.
- */
-&i2c6 {
-	status = "okay";
-};
-
-/*
- * I2c bus connected with I/O Expander and EPROMs.
- */
-&i2c7 {
-	status = "okay";
-};
-
-/*
- * I2C bus to Fan Control Board.
- */
-&i2c8 {
-	status = "okay";
-
-	i2c-switch@77 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x77>;
-
-		imux32: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux33: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux34: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux35: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux36: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux37: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux38: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux39: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-/*
- * I2C bus to CMM CPLD.
- */
-&i2c13 {
-	status = "okay";
-};
-
-&adc {
-	status = "okay";
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&vhub {
-	status = "disabled";
-};
-
-&sdhci0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sd1_default>;
-};
-
-&sdhci1 {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge100.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-wedge100.dts
deleted file mode 100644
index b1e10f0c85c9..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge100.dts
+++ /dev/null
@@ -1,149 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-// Copyright (c) 2018 Facebook Inc.
-/dts-v1/;
-
-#include "aspeed-g4.dtsi"
-
-/ {
-	model = "Facebook Wedge 100 BMC";
-	compatible = "facebook,wedge100-bmc", "aspeed,ast2400";
-
-	aliases {
-		/*
-		 * Override the default uart aliases to avoid breaking
-		 * the legacy applications.
-		 */
-		serial0 = &uart5;
-		serial1 = &uart1;
-		serial2 = &uart3;
-		serial3 = &uart4;
-	};
-
-	chosen {
-		stdout-path = &uart3;
-		bootargs = "console=ttyS2,9600n8 root=/dev/ram rw";
-	};
-
-	memory@40000000 {
-		reg = <0x40000000 0x20000000>;
-	};
-};
-
-&wdt1 {
-	status = "okay";
-	aspeed,reset-type = "system";
-};
-
-&wdt2 {
-	status = "okay";
-	aspeed,reset-type = "system";
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "fmc0";
-#include "facebook-bmc-flash-layout.dtsi"
-	};
-};
-
-&uart1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd1_default
-		     &pinctrl_rxd1_default>;
-};
-
-&uart3 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd3_default
-		     &pinctrl_rxd3_default>;
-};
-
-&uart4 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd4_default
-		     &pinctrl_rxd4_default>;
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&mac1 {
-	status = "okay";
-	no-hw-checksum;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
-};
-
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-};
-
-&i2c5 {
-	status = "okay";
-};
-
-&i2c6 {
-	status = "okay";
-};
-
-&i2c7 {
-	status = "okay";
-
-	i2c-switch@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-	};
-};
-
-&i2c8 {
-	status = "okay";
-};
-
-&i2c9 {
-	status = "okay";
-};
-
-&i2c10 {
-	status = "okay";
-};
-
-&i2c11 {
-	status = "okay";
-};
-
-&i2c12 {
-	status = "okay";
-};
-
-&i2c13 {
-	status = "okay";
-};
-
-&vhub {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
deleted file mode 100644
index c1c9cd30f980..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ /dev/null
@@ -1,972 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-// Copyright 2019 IBM Corp.
-/dts-v1/;
-
-#include "aspeed-g6.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-
-/ {
-	model = "Rainier";
-	compatible = "ibm,rainier-bmc", "aspeed,ast2600";
-
-	aliases {
-		serial4 = &uart5;
-	};
-
-	chosen {
-		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200n8";
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		flash_memory: region@B8000000 {
-			no-map;
-			reg = <0xB8000000 0x04000000>; /* 64M */
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		ps0-presence {
-			label = "ps0-presence";
-			gpios = <&gpio0 ASPEED_GPIO(S, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(S, 0)>;
-		};
-
-		ps1-presence {
-			label = "ps1-presence";
-			gpios = <&gpio0 ASPEED_GPIO(S, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(S, 1)>;
-		};
-
-		ps2-presence {
-			label = "ps2-presence";
-			gpios = <&gpio0 ASPEED_GPIO(S, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(S, 2)>;
-		};
-
-		ps3-presence {
-			label = "ps3-presence";
-			gpios = <&gpio0 ASPEED_GPIO(S, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(S, 3)>;
-		};
-	};
-
-};
-
-&emmc_controller {
-	status = "okay";
-};
-
-&emmc {
-	status = "okay";
-};
-
-&ibt {
-	status = "okay";
-};
-
-&i2c0 {
-	status = "okay";
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-};
-
-&i2c1 {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-
-	power-supply@68 {
-		compatible = "ibm,cffps2";
-		reg = <0x68>;
-	};
-
-	power-supply@69 {
-		compatible = "ibm,cffps2";
-		reg = <0x69>;
-	};
-
-	power-supply@6a {
-		compatible = "ibm,cffps2";
-		reg = <0x6a>;
-	};
-
-	power-supply@6b {
-		compatible = "ibm,cffps2";
-		reg = <0x6b>;
-	};
-};
-
-&i2c4 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-
-	eeprom@52 {
-		compatible = "atmel,24c64";
-		reg = <0x52>;
-	};
-};
-
-&i2c5 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-};
-
-&i2c6 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-
-	tmp275@4b {
-		compatible = "ti,tmp275";
-		reg = <0x4b>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-
-	eeprom@52 {
-		compatible = "atmel,24c64";
-		reg = <0x52>;
-	};
-
-	eeprom@53 {
-		compatible = "atmel,24c64";
-		reg = <0x53>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
-
-	si7021-a20@20 {
-		compatible = "silabs,si7020";
-		reg = <0x20>;
-	};
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	max31785@52 {
-		compatible = "maxim,max31785a";
-		reg = <0x52>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fan@0 {
-			compatible = "pmbus-fan";
-			reg = <0>;
-			tach-pulses = <2>;
-		};
-
-		fan@1 {
-			compatible = "pmbus-fan";
-			reg = <1>;
-			tach-pulses = <2>;
-		};
-
-		fan@2 {
-			compatible = "pmbus-fan";
-			reg = <2>;
-			tach-pulses = <2>;
-		};
-
-		fan@3 {
-			compatible = "pmbus-fan";
-			reg = <3>;
-			tach-pulses = <2>;
-		};
-	};
-
-	pca0: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-		};
-	};
-
-	dps: dps310@76 {
-		compatible = "infineon,dps310";
-		reg = <0x76>;
-		#io-channel-cells = <0>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-};
-
-&i2c8 {
-	status = "okay";
-
-	ucd90320@b {
-		compatible = "ti,ucd90160";
-		reg = <0x0b>;
-	};
-
-	ucd90320@c {
-		compatible = "ti,ucd90160";
-		reg = <0x0c>;
-	};
-
-	ucd90320@11 {
-		compatible = "ti,ucd90160";
-		reg = <0x11>;
-	};
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-};
-
-&i2c9 {
-	status = "okay";
-
-	ir35221@42 {
-		compatible = "infineon,ir35221";
-		reg = <0x42>;
-	};
-
-	ir35221@43 {
-		compatible = "infineon,ir35221";
-		reg = <0x43>;
-	};
-
-	ir35221@44 {
-		compatible = "infineon,ir35221";
-		reg = <0x44>;
-	};
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	tmp423b@4d {
-		compatible = "ti,tmp423";
-		reg = <0x4d>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-	ir35221@73 {
-		compatible = "infineon,ir35221";
-		reg = <0x73>;
-	};
-
-	ir35221@74 {
-		compatible = "infineon,ir35221";
-		reg = <0x74>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-	};
-};
-
-&i2c10 {
-	status = "okay";
-
-	ir35221@42 {
-		compatible = "infineon,ir35221";
-		reg = <0x42>;
-	};
-
-	ir35221@43 {
-		compatible = "infineon,ir35221";
-		reg = <0x43>;
-	};
-
-	ir35221@44 {
-		compatible = "infineon,ir35221";
-		reg = <0x44>;
-	};
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	tmp423b@4d {
-		compatible = "ti,tmp423";
-		reg = <0x4d>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-	ir35221@73 {
-		compatible = "infineon,ir35221";
-		reg = <0x73>;
-	};
-
-	ir35221@74 {
-		compatible = "infineon,ir35221";
-		reg = <0x74>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-	};
-};
-
-&i2c11 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-};
-
-&i2c12 {
-	status = "okay";
-};
-
-&i2c13 {
-	status = "okay";
-};
-
-&i2c14 {
-	status = "okay";
-};
-
-&i2c15 {
-	status = "okay";
-};
-
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-
-	power-supply@68 {
-		compatible = "ibm,cffps2";
-		reg = <0x68>;
-	};
-
-	power-supply@69 {
-		compatible = "ibm,cffps2";
-		reg = <0x69>;
-	};
-
-	power-supply@6a {
-		compatible = "ibm,cffps2";
-		reg = <0x6a>;
-	};
-
-	power-supply@6b {
-		compatible = "ibm,cffps2";
-		reg = <0x6b>;
-	};
-};
-
-&i2c4 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-};
-
-&i2c5 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-};
-
-&i2c6 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-
-	tmp275@4b {
-		compatible = "ti,tmp275";
-		reg = <0x4b>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
-
-	si7021-a20@20 {
-		compatible = "silabs,si7020";
-		reg = <0x20>;
-	};
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	max31785@52 {
-		compatible = "maxim,max31785a";
-		reg = <0x52>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fan@0 {
-			compatible = "pmbus-fan";
-			reg = <0>;
-			tach-pulses = <2>;
-		};
-
-		fan@1 {
-			compatible = "pmbus-fan";
-			reg = <1>;
-			tach-pulses = <2>;
-		};
-
-		fan@2 {
-			compatible = "pmbus-fan";
-			reg = <2>;
-			tach-pulses = <2>;
-		};
-
-		fan@3 {
-			compatible = "pmbus-fan";
-			reg = <3>;
-			tach-pulses = <2>;
-		};
-	};
-
-	pca0: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-		};
-	};
-
-	dps: dps310@76 {
-		compatible = "infineon,dps310";
-		reg = <0x76>;
-		#io-channel-cells = <0>;
-	};
-};
-
-&i2c8 {
-	status = "okay";
-
-	ucd90320@b {
-		compatible = "ti,ucd90160";
-		reg = <0x0b>;
-	};
-
-	ucd90320@c {
-		compatible = "ti,ucd90160";
-		reg = <0x0c>;
-	};
-
-	ucd90320@11 {
-		compatible = "ti,ucd90160";
-		reg = <0x11>;
-	};
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-};
-
-&i2c9 {
-	status = "okay";
-
-	ir35221@42 {
-		compatible = "infineon,ir35221";
-		reg = <0x42>;
-	};
-
-	ir35221@43 {
-		compatible = "infineon,ir35221";
-		reg = <0x43>;
-	};
-
-	ir35221@44 {
-		compatible = "infineon,ir35221";
-		reg = <0x44>;
-	};
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	tmp423b@4d {
-		compatible = "ti,tmp423";
-		reg = <0x4d>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-	ir35221@73 {
-		compatible = "infineon,ir35221";
-		reg = <0x73>;
-	};
-
-	ir35221@74 {
-		compatible = "infineon,ir35221";
-		reg = <0x74>;
-	};
-};
-
-&i2c10 {
-	status = "okay";
-
-	ir35221@42 {
-		compatible = "infineon,ir35221";
-		reg = <0x42>;
-	};
-
-	ir35221@43 {
-		compatible = "infineon,ir35221";
-		reg = <0x43>;
-	};
-
-	ir35221@44 {
-		compatible = "infineon,ir35221";
-		reg = <0x44>;
-	};
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	tmp423b@4d {
-		compatible = "ti,tmp423";
-		reg = <0x4d>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-	ir35221@73 {
-		compatible = "infineon,ir35221";
-		reg = <0x73>;
-	};
-
-	ir35221@74 {
-		compatible = "infineon,ir35221";
-		reg = <0x74>;
-	};
-};
-
-&i2c11 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-};
-
-&i2c12 {
-	status = "okay";
-};
-
-&i2c13 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-};
-
-&i2c14 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-};
-
-&i2c15 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-};
-
-&vuart1 {
-	status = "okay";
-};
-
-&lpc_ctrl {
-	status = "okay";
-	memory-region = <&flash_memory>;
-};
-
-&mac2 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rmii3_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
-		 <&syscon ASPEED_CLK_MAC3RCLK>;
-	clock-names = "MACCLK", "RCLK";
-	use-ncsi;
-};
-
-&mac3 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rmii4_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
-		 <&syscon ASPEED_CLK_MAC4RCLK>;
-	clock-names = "MACCLK", "RCLK";
-	use-ncsi;
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout-128.dtsi"
-	};
-
-	flash@1 {
-		status = "okay";
-		m25p,fast-read;
-		label = "alt-bmc";
-		spi-max-frequency = <50000000>;
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "pnor";
-		spi-max-frequency = <100000000>;
-	};
-};
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
new file mode 100644
index 000000000000..d3ac20e316d0
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ASPEED) += \
+	aspeed-ast2500-evb.dtb \
+	aspeed-ast2600-evb-a1.dtb \
+	aspeed-ast2600-evb.dtb \
+	aspeed-bmc-amd-daytonax.dtb \
+	aspeed-bmc-amd-ethanolx.dtb \
+	aspeed-bmc-ampere-mtjade.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
+	aspeed-bmc-arm-stardragon4800-rep2.dtb \
+	aspeed-bmc-asrock-e3c246d4i.dtb \
+	aspeed-bmc-asrock-romed8hm3.dtb \
+	aspeed-bmc-bytedance-g220a.dtb \
+	aspeed-bmc-delta-ahe50dc.dtb \
+	aspeed-bmc-facebook-bletchley.dtb \
+	aspeed-bmc-facebook-cloudripper.dtb \
+	aspeed-bmc-facebook-cmm.dtb \
+	aspeed-bmc-facebook-elbert.dtb \
+	aspeed-bmc-facebook-fuji.dtb \
+	aspeed-bmc-facebook-galaxy100.dtb \
+	aspeed-bmc-facebook-greatlakes.dtb \
+	aspeed-bmc-facebook-minerva-cmc.dtb \
+	aspeed-bmc-facebook-minipack.dtb \
+	aspeed-bmc-facebook-tiogapass.dtb \
+	aspeed-bmc-facebook-wedge40.dtb \
+	aspeed-bmc-facebook-wedge100.dtb \
+	aspeed-bmc-facebook-wedge400.dtb \
+	aspeed-bmc-facebook-yamp.dtb \
+	aspeed-bmc-facebook-yosemitev2.dtb \
+	aspeed-bmc-facebook-yosemite4.dtb \
+	aspeed-bmc-ibm-bonnell.dtb \
+	aspeed-bmc-ibm-everest.dtb \
+	aspeed-bmc-ibm-rainier.dtb \
+	aspeed-bmc-ibm-rainier-1s4u.dtb \
+	aspeed-bmc-ibm-rainier-4u.dtb \
+	aspeed-bmc-intel-s2600wf.dtb \
+	aspeed-bmc-inspur-fp5280g2.dtb \
+	aspeed-bmc-inspur-nf5280m6.dtb \
+	aspeed-bmc-inspur-on5263m5.dtb \
+	aspeed-bmc-lenovo-hr630.dtb \
+	aspeed-bmc-lenovo-hr855xg2.dtb \
+	aspeed-bmc-microsoft-olympus.dtb \
+	aspeed-bmc-opp-lanyang.dtb \
+	aspeed-bmc-opp-mowgli.dtb \
+	aspeed-bmc-opp-nicole.dtb \
+	aspeed-bmc-opp-palmetto.dtb \
+	aspeed-bmc-opp-romulus.dtb \
+	aspeed-bmc-opp-swift.dtb \
+	aspeed-bmc-opp-tacoma.dtb \
+	aspeed-bmc-opp-vesnin.dtb \
+	aspeed-bmc-opp-witherspoon.dtb \
+	aspeed-bmc-opp-zaius.dtb \
+	aspeed-bmc-portwell-neptune.dtb \
+	aspeed-bmc-qcom-dc-scm-v1.dtb \
+	aspeed-bmc-quanta-q71l.dtb \
+	aspeed-bmc-quanta-s6q.dtb \
+	aspeed-bmc-supermicro-x11spi.dtb \
+	aspeed-bmc-inventec-starscream.dtb \
+	aspeed-bmc-inventec-transformers.dtb \
+	aspeed-bmc-tyan-s7106.dtb \
+	aspeed-bmc-tyan-s8036.dtb \
+	aspeed-bmc-ufispace-ncplite.dtb \
+	aspeed-bmc-vegman-n110.dtb \
+	aspeed-bmc-vegman-rx20.dtb \
+	aspeed-bmc-vegman-sx20.dtb
diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed/aspeed-ast2500-evb.dts
index 8bec21ed0de5..a497dd135491 100644
--- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-ast2500-evb.dts
@@ -5,7 +5,7 @@
 
 / {
 	model = "AST2500 EVB";
-	compatible = "aspeed,ast2500";
+	compatible = "aspeed,ast2500-evb", "aspeed,ast2500";
 
 	aliases {
 		serial4 = &uart5;
@@ -13,7 +13,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
+		bootargs = "console=tty0 console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -129,3 +129,7 @@
      status = "okay";
      memory-region = <&gfx_memory>;
 };
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb-a1.dts b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb-a1.dts
new file mode 100644
index 000000000000..f34a2b1ec2f0
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb-a1.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2021 IBM Corp.
+
+#include "aspeed-ast2600-evb.dts"
+
+/ {
+	model = "AST2600 A1 EVB";
+	compatible = "aspeed,ast2600-evb-a1", "aspeed,ast2600-evb", "aspeed,ast2600";
+
+	/delete-node/regulator-vcc-sdhci0;
+	/delete-node/regulator-vcc-sdhci1;
+	/delete-node/regulator-vccq-sdhci0;
+	/delete-node/regulator-vccq-sdhci1;
+};
+
+/delete-node/ &sdc;
diff --git a/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb.dts
new file mode 100644
index 000000000000..de83c0eb1d6e
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb.dts
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2019 IBM Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "AST2600 EVB";
+	compatible = "aspeed,ast2600-evb", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	vcc_sdhci0: regulator-vcc-sdhci0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhci0: regulator-vccq-sdhci0 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	vcc_sdhci1: regulator-vcc-sdhci1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhci1: regulator-vccq-sdhci1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+
+&mac1 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy1>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&uart5 {
+	// Workaround for A0
+	compatible = "snps,dw-apb-uart";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+
+	temp@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	lm75@4d {
+		compatible = "national,lm75";
+		reg = <0x4d>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&fsim0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&sdc {
+	status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci0>;
+	vqmmc-supply = <&vccq_sdhci0>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci1>;
+	vqmmc-supply = <&vccq_sdhci1>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&vhub {
+	status = "okay";
+	pinctrl-names = "default";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-daytonax.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-daytonax.dts
new file mode 100644
index 000000000000..64bb9bf92de2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-daytonax.dts
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "AMD DaytonaX BMC";
+	compatible = "amd,daytonax-bmc", "aspeed,ast2500";
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-fault {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		led-identify {
+			gpios = <&gpio ASPEED_GPIO(A, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
+			<&adc 10>, <&adc 11>, <&adc 12>, <&adc 13>, <&adc 14>,
+			<&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+};
+
+&uart1 {
+	//Host Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+		&pinctrl_rxd1_default
+		&pinctrl_nrts1_default
+		&pinctrl_ndtr1_default
+		&pinctrl_ndsr1_default
+		&pinctrl_ncts1_default
+		&pinctrl_ndcd1_default
+		&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	//BMC Console
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x3f8>;
+	aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default
+		&pinctrl_adc10_default
+		&pinctrl_adc11_default
+		&pinctrl_adc12_default
+		&pinctrl_adc13_default
+		&pinctrl_adc14_default
+		&pinctrl_adc15_default>;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"","","led-fault","led-identify","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"id-button","","","","","","","",
+	/*D0-D7*/	"","","ASSERT_BMC_READY","","","","","",
+	/*E0-E7*/	"reset-button","reset-control","power-button","power-control","",
+			"power-good","power-ok","",
+	/*F0-F7*/	"","","","","","","BATTERY_DETECT","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"FM_BMC_READ_SPD_TEMP","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>, <0x81>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+		&pinctrl_pwm1_default
+		&pinctrl_pwm2_default
+		&pinctrl_pwm3_default
+		&pinctrl_pwm4_default
+		&pinctrl_pwm5_default
+		&pinctrl_pwm6_default
+		&pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@1 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	fan@2 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	fan@6 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+
+	fan@8 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+	};
+
+	fan@9 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+	};
+
+	fan@10 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+	};
+
+	fan@11 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+	};
+
+	fan@12 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+	};
+
+	fan@13 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+	};
+
+	fan@14 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
+	};
+
+	fan@15 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
+	};
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-ethanolx.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-ethanolx.dts
new file mode 100644
index 000000000000..6bded774c457
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-ethanolx.dts
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020 AMD Inc.
+// Author: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "AMD EthanolX BMC";
+	compatible = "amd,ethanolx-bmc", "aspeed,ast2500";
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+
+	aliases {
+		serial0 = &uart1;
+		serial4 = &uart5;
+	};
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+	leds {
+		compatible = "gpio-leds";
+
+		fault {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(A, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+		 <&syscon ASPEED_CLK_MAC1RCLK>;
+	clock-names = "MACCLK", "RCLK";
+};
+
+&uart1 {
+	//Host Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+		     &pinctrl_rxd1_default
+		     &pinctrl_nrts1_default
+		     &pinctrl_ncts1_default>;
+};
+
+&uart5 {
+	//BMC Console
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		     &pinctrl_adc1_default
+		     &pinctrl_adc2_default
+		     &pinctrl_adc3_default
+		     &pinctrl_adc4_default>;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"","","FAULT_LED","CHASSIS_ID_LED","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"CHASSIS_ID_BTN","INTRUDER","AC_LOSS","","","","","",
+	/*D0-D7*/	"HDT_DBREQ","LOCAL_SPI_ROM_SEL","FPGA_SPI_ROM_SEL","JTAG_MUX_S",
+			"JTAG_MUX_OE","HDT_SEL","ASERT_WARM_RST_BTN","FPGA_RSVD",
+	/*E0-E7*/	"","","MON_P0_PWR_BTN","MON_P0_RST_BTN","MON_P0_NMI_BTN",
+			"MON_P0_PWR_GOOD","MON_PWROK","MON_RESET",
+	/*F0-F7*/	"MON_P0_PROCHOT","MON_P1_PROCHOT","MON_P0_THERMTRIP",
+			"MON_P1_THERMTRIP","P0_PRESENT","P1_PRESENT","MON_ATX_PWR_OK","",
+	/*G0-G7*/	"BRD_REV_ID_3","BRD_REV_ID_2","BRD_REV_ID_1","BRD_REV_ID_0",
+			"P0_APML_ALERT","P1_APML_ALERT","FPGA ALERT","",
+	/*H0-H7*/	"BRD_ID_0","BRD_ID_1","BRD_ID_2","BRD_ID_3",
+			"PCIE_DISCONNECTED","USB_DISCONNECTED","SPARE_0","SPARE_1",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"ASSERT_PWR_BTN","ASSERT_RST_BTN","ASSERT_NMI_BTN",
+			"ASSERT_LOCAL_LOCK","ASSERT_P0_PROCHOT","ASSERT_P1_PROCHOT",
+			"ASSERT_CLR_CMOS","ASSERT_BMC_READY",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"P0_VDD_CORE_RUN_VRHOT","P0_VDD_SOC_RUN_VRHOT",
+			"P0_VDD_MEM_ABCD_SUS_VRHOT","P0_VDD_MEM_EFGH_SUS_VRHOT",
+			"P1_VDD_CORE_RUN_VRHOT","P1_VDD_SOC_RUN_VRHOT",
+			"P1_VDD_MEM_ABCD_SUS_VRHOT","P1_VDD_MEM_EFGH_SUS_VRHOT",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","SENSOR THERM","","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+//APML for P0
+&i2c0 {
+	status = "okay";
+};
+
+//APML for P1
+&i2c1 {
+	status = "okay";
+};
+
+//FPGA
+&i2c2 {
+	status = "okay";
+};
+
+//24LC128 EEPROM
+&i2c3 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <64>;
+	};
+};
+
+//P0 Power regulators
+&i2c4 {
+	status = "okay";
+};
+
+//P1 Power regulators
+&i2c5 {
+	status = "okay";
+};
+
+//P0/P1 Thermal diode
+&i2c6 {
+	status = "okay";
+};
+
+// Thermal Sensors
+&i2c7 {
+	status = "okay";
+
+	lm75a@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+	};
+
+	lm75a@49 {
+		compatible = "national,lm75a";
+		reg = <0x49>;
+	};
+
+	lm75a@4a {
+		compatible = "national,lm75a";
+		reg = <0x4a>;
+	};
+
+	lm75a@4b {
+		compatible = "national,lm75a";
+		reg = <0x4b>;
+	};
+
+	lm75a@4c {
+		compatible = "national,lm75a";
+		reg = <0x4c>;
+	};
+
+	lm75a@4d {
+		compatible = "national,lm75a";
+		reg = <0x4d>;
+	};
+
+	lm75a@4e {
+		compatible = "national,lm75a";
+		reg = <0x4e>;
+	};
+
+	lm75a@4f {
+		compatible = "national,lm75a";
+		reg = <0x4f>;
+	};
+};
+
+//BMC I2C
+&i2c8 {
+	status = "okay";
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x60>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x62>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA2>;
+};
+
+&kcs4 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x97DE>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>, <0x81>;
+};
+
+&lpc_ctrl {
+	//Enable lpc clock
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x3f8>;
+	aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+	&pinctrl_pwm1_default
+	&pinctrl_pwm2_default
+	&pinctrl_pwm3_default
+	&pinctrl_pwm4_default
+	&pinctrl_pwm5_default
+	&pinctrl_pwm6_default
+	&pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjade.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjade.dts
new file mode 100644
index 000000000000..8ab5f301f926
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjade.dts
@@ -0,0 +1,822 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt. Jade BMC";
+	compatible = "ampere,mtjade-bmc", "aspeed,ast2500";
+
+	aliases {
+		/*
+		 *  i2c bus 50-57 assigned to NVMe slot 0-7
+		 */
+		i2c50 = &nvmeslot_0;
+		i2c51 = &nvmeslot_1;
+		i2c52 = &nvmeslot_2;
+		i2c53 = &nvmeslot_3;
+		i2c54 = &nvmeslot_4;
+		i2c55 = &nvmeslot_5;
+		i2c56 = &nvmeslot_6;
+		i2c57 = &nvmeslot_7;
+
+		/*
+		 *  i2c bus 60-67 assigned to NVMe slot 8-15
+		 */
+		i2c60 = &nvmeslot_8;
+		i2c61 = &nvmeslot_9;
+		i2c62 = &nvmeslot_10;
+		i2c63 = &nvmeslot_11;
+		i2c64 = &nvmeslot_12;
+		i2c65 = &nvmeslot_13;
+		i2c66 = &nvmeslot_14;
+		i2c67 = &nvmeslot_15;
+
+		/*
+		 *  i2c bus 70-77 assigned to NVMe slot 16-23
+		 */
+		i2c70 = &nvmeslot_16;
+		i2c71 = &nvmeslot_17;
+		i2c72 = &nvmeslot_18;
+		i2c73 = &nvmeslot_19;
+		i2c74 = &nvmeslot_20;
+		i2c75 = &nvmeslot_21;
+		i2c76 = &nvmeslot_22;
+		i2c77 = &nvmeslot_23;
+
+		/*
+		 *  i2c bus 80-81 assigned to NVMe M2 slot 0-1
+		 */
+		i2c80 = &nvme_m2_0;
+		i2c81 = &nvme_m2_1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fault {
+			gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>;
+		};
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpioA0mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio ASPEED_GPIO(A, 0) GPIO_ACTIVE_LOW>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 8>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 9>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 10>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 11>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 12>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 13>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc 14>, <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		/* spi-max-frequency = <50000000>; */
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		/* spi-max-frequency = <100000000>; */
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			uefi@400000 {
+				reg = <0x400000 0x1C00000>;
+				label = "pnor-uefi";
+			};
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			 &pinctrl_rxd1_default
+			 &pinctrl_ncts1_default
+			 &pinctrl_nrts1_default>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			 &pinctrl_rxd2_default>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd3_default
+			 &pinctrl_rxd3_default>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd4_default
+			 &pinctrl_rxd4_default>;
+};
+
+/* The BMC's uart */
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+		 <&syscon ASPEED_CLK_MAC1RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c0 {
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+	smpro@4f {
+		compatible = "ampere,smpro";
+		reg = <0x4f>;
+	};
+	smpro@4e {
+		compatible = "ampere,smpro";
+		reg = <0x4e>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "microchip,24c64", "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	inlet_mem2: tmp175@28 {
+		compatible = "ti,tmp175";
+		reg = <0x28>;
+	};
+
+	inlet_cpu: tmp175@29 {
+		compatible = "ti,tmp175";
+		reg = <0x29>;
+	};
+
+	inlet_mem1: tmp175@2a {
+		compatible = "ti,tmp175";
+		reg = <0x2a>;
+	};
+
+	outlet_cpu: tmp175@2b {
+		compatible = "ti,tmp175";
+		reg = <0x2b>;
+	};
+
+	outlet1: tmp175@2c {
+		compatible = "ti,tmp175";
+		reg = <0x2c>;
+	};
+
+	outlet2: tmp175@2d {
+		compatible = "ti,tmp175";
+		reg = <0x2d>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_0_7: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_8_15: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+
+		nvmeslot_16_23: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		i2c-mux-idle-disconnect;
+
+		nvme_m2_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+
+		nvme_m2_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+	};
+};
+
+&nvmeslot_0_7 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+		nvmeslot_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		nvmeslot_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+		nvmeslot_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		nvmeslot_4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+		nvmeslot_5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+		nvmeslot_6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+		nvmeslot_7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+
+	};
+};
+
+&nvmeslot_8_15 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_8: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+		nvmeslot_9: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		nvmeslot_10: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+		nvmeslot_11: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		nvmeslot_12: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+		nvmeslot_13: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+		nvmeslot_14: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+		nvmeslot_15: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+	};
+};
+
+&nvmeslot_16_23 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+		nvmeslot_17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		nvmeslot_18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+		nvmeslot_19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		nvmeslot_20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+		nvmeslot_21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+		nvmeslot_22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+		nvmeslot_23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+	adm1278@10 {
+		compatible = "adi,adm1278";
+		reg = <0x10>;
+	};
+
+	adm1278@11 {
+		compatible = "adi,adm1278";
+		reg = <0x11>;
+	};
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2_default &pinctrl_pwm3_default
+			&pinctrl_pwm4_default &pinctrl_pwm5_default
+			&pinctrl_pwm6_default &pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@1 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	fan@2 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+	};
+
+	fan@5 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+	};
+
+	fan@6 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+	};
+
+	fan@7 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+	};
+
+	fan@8 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+	};
+
+	fan@9 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+	};
+
+	fan@10 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
+	};
+
+	fan@11 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
+	};
+
+};
+
+&vhub {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","","","host0-special-boot","","","","",
+	/*B0-B7*/	"i2c-backup-sel","","","",
+			"power-button","presence-cpu0","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"ps0-pgood","ps1-pgood","power-chassis-control","s0-ddr-save",
+			"power-chassis-good", "s1-ddr-save","","",
+	/*G0-G7*/	"host0-ready","host0-shd-req-n","host0-shd-ack-n",
+			"s0-overtemp-n","","","","",
+	/*H0-H7*/	"uart1-mode1","uart2-mode1","uart3-mode1","uart4-mode1",
+			"ps0-vin-good","ps1-vin-good","","i2c6-reset-n",
+	/*I0-I7*/	"presence-ps0","presence-ps1","s1-special-boot","","","","","",
+	/*J0-J7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","host0-sysreset-n","s0-spi-auth-fail-n","","","",
+	/*M0-M7*/	"","","","","s0-i2c9-alert-n","s1-i2c9-alert-n","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","identify-button","led-identify","",
+	/*R0-R7*/	"","","ext-hightemp-n","","ocp-main-pwren","reset-button","","",
+	/*S0-S7*/	"s0-vr-hot-n","s1-vr-hot-n","","",
+			"rtc-battery-voltage-read-enable","vr-pmbus-sel-n","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","bmc-vga-en-n","","","","",
+	/*Z0-Z7*/	"s0-plimit","s1-fault-alert","s1-fw-boot-ok","s0-rtc-lock","",
+			"s1-sys-auth-failure-n","s1-overtemp-n","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"s1-hightemp-n","s1-plimit","s0-ddr-addr","s1-ddr-addr","","",
+			"","",
+	/*AC0-AC7*/	"sys-pwr-gd","","spi0-program-sel","spi0-backup-sel","bmc-ok",
+			"","presence-cpu1","ocp-pgood";
+
+	i2c4-o-en-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "i2c4-o-en";
+	};
+
+	ocp-aux-pwren-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ocp-aux-pwren";
+	};
+
+	bmc-ready {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(AC, 5) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bmc-ready";
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..7b540880cef9
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,892 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial7 = &uart8;
+		serial8 = &uart9;
+
+		/*
+		 *  I2C NVMe alias port
+		 */
+		i2c100 = &backplane_0;
+		i2c48 = &nvmeslot_0;
+		i2c49 = &nvmeslot_1;
+		i2c50 = &nvmeslot_2;
+		i2c51 = &nvmeslot_3;
+		i2c52 = &nvmeslot_4;
+		i2c53 = &nvmeslot_5;
+		i2c54 = &nvmeslot_6;
+		i2c55 = &nvmeslot_7;
+
+		i2c101 = &backplane_1;
+		i2c56 = &nvmeslot_8;
+		i2c57 = &nvmeslot_9;
+		i2c58 = &nvmeslot_10;
+		i2c59 = &nvmeslot_11;
+		i2c60 = &nvmeslot_12;
+		i2c61 = &nvmeslot_13;
+		i2c62 = &nvmeslot_14;
+		i2c63 = &nvmeslot_15;
+
+		i2c102 = &backplane_2;
+		i2c64 = &nvmeslot_16;
+		i2c65 = &nvmeslot_17;
+		i2c66 = &nvmeslot_18;
+		i2c67 = &nvmeslot_19;
+		i2c68 = &nvmeslot_20;
+		i2c69 = &nvmeslot_21;
+		i2c70 = &nvmeslot_22;
+		i2c71 = &nvmeslot_23;
+
+		i2c80 = &nvme_m2_0;
+		i2c81 = &nvme_m2_1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 8>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 9>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 10>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 11>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 12>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 13>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 14>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 15>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels =	<&adc0mux 0>, <&adc0mux 1>,
+				<&adc1mux 0>, <&adc1mux 1>,
+				<&adc2mux 0>, <&adc2mux 1>,
+				<&adc3mux 0>, <&adc3mux 1>,
+				<&adc4mux 0>, <&adc4mux 1>,
+				<&adc5mux 0>, <&adc5mux 1>,
+				<&adc6mux 0>, <&adc6mux 1>,
+				<&adc7mux 0>, <&adc7mux 1>,
+				<&adc8mux 0>, <&adc8mux 1>,
+				<&adc9mux 0>, <&adc9mux 1>,
+				<&adc10mux 0>, <&adc10mux 1>,
+				<&adc11mux 0>, <&adc11mux 1>,
+				<&adc12mux 0>, <&adc12mux 1>,
+				<&adc13mux 0>, <&adc13mux 1>,
+				<&adc14mux 0>, <&adc14mux 1>,
+				<&adc15mux 0>, <&adc15mux 1>,
+				<&adc_i2c_1 0>, <&adc_i2c_1 1>,
+				<&adc_i2c_1 2>, <&adc_i2c_1 3>,
+				<&adc_i2c_1 4>, <&adc_i2c_1 5>,
+				<&adc_i2c_1 6>, <&adc_i2c_1 7>,
+				<&adc_i2c_1 8>, <&adc_i2c_1 9>,
+				<&adc_i2c_1 10>, <&adc_i2c_1 11>,
+				<&adc_i2c_1 12>, <&adc_i2c_1 13>,
+				<&adc_i2c_1 14>, <&adc_i2c_1 15>,
+				<&adc0 0>, <&adc0 1>,
+				<&adc0 2>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	bus-frequency = <1000000>;
+	multi-master;
+	mctp-controller;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c_0: adc@14 {
+		compatible = "lltc,ltc2497";
+		reg = <0x14>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	adc_i2c_1: adc@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp112";
+		reg = <0x48>;
+	};
+
+	gpio@77 {
+		compatible = "nxp,pca9539";
+		reg = <0x77>;
+		gpio-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#gpio-cells = <2>;
+
+		bmc-ocp0-en-hog {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_LOW>;
+			output-high;
+			line-name = "bmc-ocp0-en-n";
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		backplane_1: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+			};
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_8: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_9: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_10: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_11: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+				nvmeslot_12: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_13: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_14: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_15: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			tmp432@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+		};
+
+		backplane_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+			};
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_16: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_17: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_18: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_19: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+				nvmeslot_20: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_21: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_22: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_23: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			tmp432@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+		};
+
+		backplane_0: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+			};
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+				nvmeslot_4: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_5: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_6: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_7: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			tmp432@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvme_m2_0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+
+				nvme_m2_1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+			};
+		};
+	};
+};
+
+&i2c11 {
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","bmc-debug-mode","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"","eth-phy-int-n","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-csout-prochot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","","","",
+	/*H0-H7*/	"jtag-program-sel","fpga-program-b","wd-disable-n",
+			"power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","s1-heartbeat","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","host0-ready","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","s0-fw-boot-ok","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","s1-pcp-pgood",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","cpld-s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+
+	ocp-aux-pwren-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ocp-aux-pwren";
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-arm-stardragon4800-rep2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-arm-stardragon4800-rep2.dts
index 2c29ac037d32..7c6af7f226e7 100644
--- a/arch/arm/boot/dts/aspeed-bmc-arm-stardragon4800-rep2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-arm-stardragon4800-rep2.dts
@@ -10,7 +10,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts
new file mode 100644
index 000000000000..c4b2efbfdf56
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/{
+	model = "ASRock E3C246D4I BMC";
+	compatible = "asrock,e3c246d4i-bmc", "aspeed,ast2500";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=tty0 console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat {
+			/* BMC_HB_LED_N */
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		system-fault {
+			/* SYSTEM_FAULT_LED_N */
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
+			panic-indicator;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		uid-button {
+			label = "uid-button";
+			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(F, 1)>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
+			<&adc 10>, <&adc 11>, <&adc 12>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>; /* 50 MHz */
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x2f8>;
+	aspeed,lpc-interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* thermal sensor, one diode run to a disconnected header */
+	w83773g@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* FRU EEPROM */
+	eeprom@57 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+};
+
+&video {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "BMC_MAC1_INTB", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI",
+			"", "", "", "",
+		/*  B */ "", "", "", "", "", "IRQ_BMC_PCH_SMI_LPC_N", "", "",
+		/*  C */ "", "", "", "", "", "", "", "",
+		/*  D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON",
+			"", "", "", "",
+		/*  E */ "", "", "", "", "", "", "", "",
+		/*  F */ "LOCATORLED_STATUS_N", "LOCATORBTN", "", "",
+			"", "", "BMC_PCH_SCI_LPC", "BMC_NCSI_MUX_CTL",
+		/*  G */ "HWM_BAT_EN", "CHASSIS_ID0", "CHASSIS_ID1", "CHASSIS_ID2",
+			"BMC_ALERT1_N_R", "BMC_ALERT2_N_R", "BMC_ALERT3_N", "SML0ALERT",
+		/*  H */ "FM_ME_RCVR_N", "O_PWROK", "SKL_CNL_R", "D4_DIMM_EVENT_3V_N",
+			"MFG_MODE_N", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN",
+		/*  I */ "", "", "", "", "", "", "", "",
+		/*  J */ "BMC_READY", "BMC_PCH_BIOS_CS_N", "BMC_SMI", "",
+			"", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "BMC_CTS1", "BMC_DCD1", "BMC_DSR1", "BMC_RI1",
+			"BMC_DTR1", "BMC_RTS1", "BMC_TXD1", "BMC_RXD1",
+		/*  M */ "BMC_LAN0_DIS_N", "BMC_LAN1_DIS_N", "", "",
+			"", "", "", "",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "", "", "", "", "", "", "", "",
+		/*  Q */ "", "", "", "",
+			"BMC_SBM_PRESENT_1_N", "BMC_SBM_PRESENT_2_N",
+			"BMC_SBM_PRESENT_3_N", "BMC_PCIE_WAKE_N",
+		/*  R */ "", "", "", "", "", "", "", "",
+		/*  S */ "PCHHOT_BMC_N", "", "RSMRST",
+			"", "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "PS_PWROK", /* dummy always-high signal */
+			"", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "SLP_S3", "SLP_S5", "", "", "", "", "", "",
+		/*  Z */ "CPU_CATERR_BMC_PCH_N", "", "SYSTEM_FAULT_LED_N", "BMC_THROTTLE_N",
+			"", "", "", "",
+		/* AA */ "CPU1_THERMTRIP_LATCH_N", "", "CPU1_PROCHOT_N", "",
+			"", "", "IRQ_SMI_ACTIVE_N", "FM_BIOS_POST_CMPLT_N",
+		/* AB */ "", "", "ME_OVERRIDE", "BMC_DMI_MODIFY",
+			"", "", "", "",
+		/* AC */ "LAD0", "LAD1", "LAD2", "LAD3",
+			"CK_33M_BMC", "LFRAME", "SERIRQ", "S_PLTRST";
+
+	/* Assert BMC_READY so BIOS doesn't sit around waiting for it */
+	bmc-ready {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+			&pinctrl_adc1_default
+			&pinctrl_adc2_default
+			&pinctrl_adc3_default
+			&pinctrl_adc4_default
+			&pinctrl_adc5_default
+			&pinctrl_adc6_default
+			&pinctrl_adc7_default
+			&pinctrl_adc8_default
+			&pinctrl_adc9_default
+			&pinctrl_adc10_default
+			&pinctrl_adc11_default
+			&pinctrl_adc12_default>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&peci0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts
new file mode 100644
index 000000000000..4554abf0c7cd
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/{
+	model = "ASRock ROMED8HM3 BMC v1.00";
+	compatible = "asrock,romed8hm3-bmc", "aspeed,ast2500";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=tty0 console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		system-fault {
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>; /* 50 MHz */
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x2f8>;
+	aspeed,lpc-interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* inlet temp sensor */
+	w83773g@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* IPB temp sensor */
+	w83773g@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+
+	/* IPB PMIC */
+	lm25066@40 {
+		compatible = "lm25066";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <1000>;
+	};
+
+	/* 12VSB PMIC */
+	lm25066@41 {
+		compatible = "lm25066";
+		reg = <0x41>;
+		shunt-resistor-micro-ohms = <10000>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* Baseboard FRU eeprom */
+	eeprom@50 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3_default
+		&pinctrl_pwm4_default
+		&pinctrl_pwm5_default
+		&pinctrl_pwm6_default>;
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03 0x0b>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0c>;
+	};
+
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05 0x0d>;
+	};
+
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x0e>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "LOCATORLED_STATUS_N", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI",
+			"", "", "", "",
+		/*  B */ "POST_COMPLETE_N", "", "", "", "", "", "", "",
+		/*  C */ "", "", "", "", "PCIE_HP_SEL_N", "PCIE_SATA_SEL_N", "LOCATORBTN", "",
+		/*  D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON",
+			"", "", "", "PSU_FAN_FAIL_N",
+		/*  E */ "", "", "", "", "", "", "", "",
+		/*  F */ "NIC_PWR_GOOD", "PRSNTB0", "PRSNTB1", "PRSNTB2",
+			"PRSNTB3", "", "3VSB_PCIE1_PG", "12V_PCIE1_PG",
+		/*  G */ "HWM_BAT_EN", "CHASSIS_ID0", "CHASSIS_ID1", "CHASSIS_ID2",
+			"BMC_ALERT1_N_R", "BMC_ALERT2_N_R", "BMC_ALERT3_N", "BMC_ALERT4_N",
+		/*  H */ "X24_C1_PRSNT", "X24_C2_PRSNT", "X24_C3_PRSNT", "FM_MEM_THERM_EVENT_BMC_R_N",
+			"FACMODE", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN",
+		/*  I */ "", "", "", "", "", "", "", "",
+		/*  J */ "BMC_READY", "BMC_PCH_BIOS_CS_N", "", "P0_MA_DDR_QS_CS_N",
+			"", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "", "", "", "", "", "", "", "",
+		/*  M */ "", "", "MEZZ_PWRBRK_N", "OCP_HP_RST_EN",
+			"MAIN_PWR_EN_G", "BMC_MAIN_EN", "AUX_PWR_EN_G", "BMC_AUX_EN",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "", "", "", "", "", "", "", "",
+		/*  Q */ "", "", "", "",
+			"BMC_SMB_PRESENT_1_N", "BMC_SMB_PRESENT_2_N",
+			"BMC_SMB_PRESENT_3_N", "BMC_PCIE_WAKE_N",
+		/*  R */ "", "", "THERMALTRIP_CLEAR_N", "", "", "", "", "",
+		/*  S */ "", "", "", "", "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "", "", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "SLP_S3", "SLP_S4_S5", "NODE_ID_1", "NODE_ID_2", "", "", "", "",
+		/*  Z */ "", "", "SYSTEM_FAULT_LED_N", "FAST_THROTTLE_N",
+			"", "", "", "",
+		/* AA */ "FM_CPU0_IBMC_THERMTRIP_N", "", "PROCHOT_L_G", "",
+			"", "", "", "",
+		/* AB */ "BMC_FORCE_SELFREFRESH", "PWRGD_OUT", "", "IRQ_BMC_PCH_SMI_LPC_N",
+			"", "", "", "",
+		/* AC */ "", "", "", "", "", "", "", "";
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default
+		&pinctrl_adc10_default
+		&pinctrl_adc11_default
+		&pinctrl_adc12_default
+		&pinctrl_adc13_default
+		&pinctrl_adc14_default
+		&pinctrl_adc15_default>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-bytedance-g220a.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-bytedance-g220a.dts
new file mode 100644
index 000000000000..3f03a198a1a8
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-bytedance-g220a.dts
@@ -0,0 +1,940 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2020 Bytedance.
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Bytedance G220A BMC";
+	compatible = "bytedance,g220a-bmc", "aspeed,ast2500";
+
+	aliases {
+		serial4 = &uart5;
+		i2c14 = &channel_3_0;
+		i2c15 = &channel_3_1;
+		i2c16 = &channel_3_2;
+		i2c17 = &channel_3_3;
+		i2c18 = &channel_6_0;
+		i2c19 = &channel_6_1;
+		i2c20 = &channel_6_2;
+		i2c21 = &channel_6_3;
+		i2c22 = &channel_6_4;
+		i2c23 = &channel_6_5;
+		i2c24 = &channel_6_6;
+		i2c25 = &channel_6_7;
+		i2c26 = &channel_6_8;
+		i2c27 = &channel_6_9;
+		i2c28 = &channel_6_10;
+		i2c29 = &channel_6_11;
+		i2c30 = &channel_6_12;
+		i2c31 = &channel_6_13;
+		i2c32 = &channel_6_14;
+		i2c33 = &channel_6_15;
+		i2c34 = &channel_6_16;
+		i2c35 = &channel_6_17;
+		i2c36 = &channel_6_18;
+		i2c37 = &channel_6_19;
+		i2c38 = &channel_6_20;
+		i2c39 = &channel_6_21;
+		i2c40 = &channel_6_22;
+		i2c41 = &channel_6_23;
+		i2c42 = &channel_6_24;
+		i2c43 = &channel_6_25;
+		i2c44 = &channel_10_0;
+		i2c45 = &channel_10_1;
+		i2c46 = &channel_10_2;
+		i2c47 = &channel_10_3;
+		i2c48 = &channel_10_4;
+		i2c49 = &channel_10_5;
+		i2c50 = &channel_10_6;
+		i2c51 = &channel_10_7;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@bc000000 {
+			no-map;
+			reg = <0xbc000000 0x04000000>; /* 64M */
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		bmc_alive {
+			label = "bmc_alive";
+			gpios = <&gpio ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+			led-pattern = <1000 1000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		event-burn-in-signal {
+			label = "burn-in";
+			gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(R, 5)>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-rear-riser1-presence {
+			label = "rear-riser1-presence";
+			gpios = <&pca0 1 GPIO_ACTIVE_LOW>;
+			linux,code = <1>;
+		};
+
+		event-alrt-pvddq-cpu0 {
+			label = "alrt-pvddq-cpu0";
+			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
+			linux,code = <2>;
+		};
+
+		event-rear-riser0-presence {
+			label = "rear-riser0-presence";
+			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
+			linux,code = <3>;
+		};
+
+		event-fault-pvddq-cpu0 {
+			label = "fault-pvddq-cpu0";
+			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
+			linux,code = <4>;
+		};
+
+		event-alrt-pvddq-cpu1 {
+			label = "alrt-pvddq-cpu1";
+			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
+			linux,code = <5>;
+		};
+
+		event-fault-pvddq-cpu1 {
+			label = "alrt-pvddq-cpu1";
+			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		event-fault-pvccin-cpu1 {
+			label = "fault-pvccin-cpuq";
+			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
+			linux,code = <7>;
+		};
+
+		event-bmc-rom0-wp {
+			label = "bmc-rom0-wp";
+			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
+			linux,code = <8>;
+		};
+
+		event-bmc-rom1-wp {
+			label = "bmc-rom1-wp";
+			gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
+			linux,code = <9>;
+		};
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
+			linux,code = <10>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
+			linux,code = <11>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca1 4 GPIO_ACTIVE_LOW>;
+			linux,code = <12>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca1 5 GPIO_ACTIVE_LOW>;
+			linux,code = <13>;
+		};
+
+		event-fan4-presence {
+			label = "fan4-presence";
+			gpios = <&pca1 6 GPIO_ACTIVE_LOW>;
+			linux,code = <14>;
+		};
+
+		event-fan5-presence {
+			label = "fan5-presence";
+			gpios = <&pca1 7 GPIO_ACTIVE_LOW>;
+			linux,code = <15>;
+		};
+
+		event-front-bp1-presence {
+			label = "front-bp1-presence";
+			gpios = <&pca1 8 GPIO_ACTIVE_LOW>;
+			linux,code = <16>;
+		};
+
+		event-rear-bp-presence {
+			label = "rear-bp-presence";
+			gpios = <&pca1 9 GPIO_ACTIVE_LOW>;
+			linux,code = <17>;
+		};
+
+		event-fault-pvccin-cpu0 {
+			label = "fault-pvccin-cpu0";
+			gpios = <&pca1 10 GPIO_ACTIVE_LOW>;
+			linux,code = <18>;
+		};
+
+		event-alrt-p1v05-pvcc {
+			label = "alrt-p1v05-pvcc1";
+			gpios = <&pca1 11 GPIO_ACTIVE_LOW>;
+			linux,code = <19>;
+		};
+
+		event-fault-p1v05-pvccio {
+			label = "alrt-p1v05-pvcc1";
+			gpios = <&pca1 12 GPIO_ACTIVE_LOW>;
+			linux,code = <20>;
+		};
+
+		event-alrt-p1v8-pvccio {
+			label = "alrt-p1v8-pvccio";
+			gpios = <&pca1 13 GPIO_ACTIVE_LOW>;
+			linux,code = <21>;
+		};
+
+		event-fault-p1v8-pvccio {
+			label = "fault-p1v8-pvccio";
+			gpios = <&pca1 14 GPIO_ACTIVE_LOW>;
+			linux,code = <22>;
+		};
+
+		event-front-bp0-presence {
+			label = "front-bp0-presence";
+			gpios = <&pca1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <23>;
+		};
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		label = "bmc";
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		label = "alt-bmc";
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&wdt2 {
+	status = "okay";
+	aspeed,alt-boot;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"SMRST_OCP_N","MAC2_LINK","BMC_CPLD_SMB_RST_R_N","BMC_CPLD_GPIO0",
+			"","","","",
+	/*B0-B7*/	"BMC_INIT_R_OK","FM_BOARD_REV_ID2","FM_PROJECT_ID7","FAULT_P12V_STBY_N",
+			"","CPU0_PROCHOT_LVT3_N","","BIOS_LOAD_DEFAULT_R_N",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"FM_PROJECT_ID0","FM_PROJECT_ID1","FM_PROJECT_ID2","FM_PROJECT_ID3",
+			"FM_PROJECT_ID4","FM_PROJECT_ID5","","",
+	/*F0-F7*/	"PSU0_PRSNT_N","PSU1_PRSNT_N","","FAULT_P12V_NVME_N",
+			"BIOS_DEBUG_MODE_R_N","DISABLE_CPU_DDR_R_SPD","COOLING_STRATEGY",
+			"PCH_GLB_RST_N",
+	/*G0-G7*/	"P12V_PMBUS_ALERT_N","CPLD_ALERT_N","BMC_RELOAD_N",
+			"P12V_PVDDQ_PMBUS_ALERT_N","BMC_JTAG_TCK_MUX_R_SEL","","NMI_OUT",
+			"NMI_BUTTON",
+	/*H0-H7*/	"BMC_CPLD_JTAG_TDI","BMC_CPLD_JTAG_TDO","BMC_CPLD_JTAG_TCK",
+			"BMC_CPLD_JTAG_TMS","FM_PROJECT_ID6","FM_BOARD_REV_ID0",
+			"PCA9546_U70_RST_N","IRQ_SML0_ALERT_N",
+	/*I0-I7*/	"FAULT_FRONT_RISER_P12V_N","FAULT_OCP_P12V_N","FM_BMC_PCH_SCI_R_N",
+			"","","","","",
+	/*J0-J7*/	"FM_CPU0_SKTOCC_N","FM_CPU1_SKTOCC_N","FM_CPU1_DISABLE_COD_N",
+			"","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"P12V_FAULT_N","PWRGD_P12V_PCIE_RISER","","LEAKAGE_DETECT_INPUT_N",
+			"","IRQ_SML1_PMBUS_ALERT_N","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","FM_PCH_THERMTRIP_N","CHASSIS_INTRUSION",
+	/*R0-R7*/	"","PVCCIN_CPU1_SMBALERT_N","BMC_PREQ_R_N","FAULT_P12V_PCIE_RISER_N",
+			"ALT_P12V_PCIE_RISER_N","BURN_BOARD_N","PVCCIN_CPU0_SMBALERT_N","",
+	/*S0-S7*/	"BMC_PRDY_N","SIO_POWER_GOOD","FM_BMC_PWR_DEBUG_R_N",
+			"FM_BMC_XDP_DEBUG_EN","","STRAP_BMC_BATTERY_GPIOS5","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","PWRGD_PSU0_PWROK","CPU1_PROCHOT_LVT3_N","IRQ_BMC_PCH_SMI_LPC_N",
+			"","","","",
+	/*Z0-Z7*/	"XDP_PRSNT_N","BMC_XDP_SYS_PWROK","BMC_XDP_JTAG_SEL",
+			"PCH_BMC_SMI_ACTIVE_R_N","","","","",
+	/*AA0-AA7*/	"PWRGD_P12V_STBY_OCP","PS_PWROK","RST_PLTRST_BMC_R_N","HDA_SDO_R",
+			"FM_SLPS4_R_N","PWRGD_PSU1_PWROK","POWER_BUTTON","POWER_OUT",
+	/*AB0-AB7*/	"","RESET_OUT","SPI_BIOS_MODE_SELECT","POST_COMPLETE","","","","",
+	/*AC0-AC7*/	"","","","","","","","CPLD_PLTRST_B_N";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default
+			&pinctrl_nrts1_default
+			&pinctrl_ndtr1_default
+			&pinctrl_ndsr1_default
+			&pinctrl_ncts1_default
+			&pinctrl_ndcd1_default
+			&pinctrl_nri1_default>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			&pinctrl_rxd2_default
+			&pinctrl_nrts2_default
+			&pinctrl_ndtr2_default
+			&pinctrl_ndsr2_default
+			&pinctrl_ncts2_default
+			&pinctrl_ndcd2_default
+			&pinctrl_nri2_default>;
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+		 <&syscon ASPEED_CLK_MAC1RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel_3_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_3_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_3_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_3_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	ipmb0@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+	i2c-mux@72 {
+		compatible = "nxp,pca9548";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		channel_6_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_6_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_6_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_6_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+		channel_6_4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		channel_6_5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		channel_6_6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		channel_6_7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		channel_6_8: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			i2c-mux@71 {
+				compatible = "nxp,pca9546";
+				reg = <0x71>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				channel_6_12: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+				};
+
+				channel_6_13: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				channel_6_14: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				channel_6_15: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		 };
+
+		channel_6_9: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			i2c-mux@71 {
+				compatible = "nxp,pca9546";
+				reg = <0x71>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				channel_6_16: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+				};
+
+				channel_6_17: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				channel_6_18: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				channel_6_19: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		 };
+
+		channel_6_10: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			i2c-mux@71 {
+				compatible = "nxp,pca9546";
+				reg = <0x71>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				channel_6_20: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				channel_6_21: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				channel_6_22: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				channel_6_23: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		 };
+
+		channel_6_11: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			i2c-mux@71 {
+				compatible = "nxp,pca9546";
+				reg = <0x71>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				channel_6_24: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				channel_6_25: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			 };
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+	pca0:pca9555@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@8 {
+			reg = <8>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@9 {
+			reg = <9>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@10 {
+			reg = <10>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@11 {
+			reg = <11>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@12 {
+			reg = <12>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@13 {
+			reg = <13>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	pca1:pca9555@25 {
+		compatible = "nxp,pca9555";
+		reg = <0x25>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+		gpio@8 {
+			reg = <8>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@9 {
+			reg = <9>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@10 {
+			reg = <10>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@11 {
+			reg = <11>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@12 {
+			reg = <12>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@13 {
+			reg = <13>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@14 {
+			reg = <14>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@15 {
+			reg = <15>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		channel_10_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_10_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_10_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_10_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		channel_10_4: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_10_5: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_10_6: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_10_7: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x01>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x03>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x05>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x07>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08 0x09>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a 0x0b>;
+	};
+};
+
+&gpio {
+	pin_gpio_i3 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "NCSI_BMC_R_SEL";
+	};
+
+	pin_gpio_b6 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "EN_NCSI_SWITCH_N";
+	};
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-delta-ahe50dc.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-delta-ahe50dc.dts
new file mode 100644
index 000000000000..6600f7e9bf5e
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-delta-ahe50dc.dts
@@ -0,0 +1,418 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g4.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+#define EFUSE_OUTPUT(n)					\
+	efuse##n {					\
+		compatible = "regulator-output";	\
+		vout-supply = <&efuse##n>;		\
+	}
+
+#define __stringify(x) #x
+
+#define EFUSE(hexaddr, num)							\
+	efuse@##hexaddr {							\
+		compatible = "lm25066";						\
+		reg = <0x##hexaddr>;						\
+		shunt-resistor-micro-ohms = <675>;				\
+		regulators {							\
+			efuse##num: vout0 {					\
+				regulator-name = __stringify(efuse##num##-reg);	\
+			};							\
+		};								\
+	}
+
+/{
+	model = "Delta Power AHE-50DC";
+	compatible = "delta,ahe50dc-bmc", "aspeed,ast2400";
+
+	aliases {
+		serial4 = &uart5;
+
+		/*
+		 * pca9541-arbitrated logical i2c buses are numbered as the
+		 * corresponding physical bus plus 20
+		 */
+		i2c20 = &i2carb0;
+		i2c21 = &i2carb1;
+		i2c22 = &i2carb2;
+		i2c23 = &i2carb3;
+		i2c24 = &i2carb4;
+		i2c26 = &i2carb6;
+		i2c27 = &i2carb7;
+		i2c28 = &i2carb8;
+		i2c32 = &i2carb12;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+		bootargs = "console=ttyS2,115200n8 earlycon";
+	};
+
+	memory@40000000 {
+		reg = <0x40000000 0x10000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		panic {
+			gpios = <&gpio ASPEED_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "panic";
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>;
+	};
+
+	EFUSE_OUTPUT(01);
+	EFUSE_OUTPUT(02);
+	EFUSE_OUTPUT(03);
+	EFUSE_OUTPUT(04);
+	EFUSE_OUTPUT(05);
+	EFUSE_OUTPUT(06);
+	EFUSE_OUTPUT(07);
+	EFUSE_OUTPUT(08);
+	EFUSE_OUTPUT(09);
+	EFUSE_OUTPUT(10);
+	EFUSE_OUTPUT(11);
+	EFUSE_OUTPUT(12);
+	EFUSE_OUTPUT(13);
+	EFUSE_OUTPUT(14);
+	EFUSE_OUTPUT(15);
+	EFUSE_OUTPUT(16);
+	EFUSE_OUTPUT(17);
+	EFUSE_OUTPUT(18);
+	EFUSE_OUTPUT(19);
+	EFUSE_OUTPUT(20);
+	EFUSE_OUTPUT(21);
+	EFUSE_OUTPUT(22);
+	EFUSE_OUTPUT(23);
+	EFUSE_OUTPUT(24);
+	EFUSE_OUTPUT(25);
+	EFUSE_OUTPUT(26);
+	EFUSE_OUTPUT(27);
+	EFUSE_OUTPUT(28);
+	EFUSE_OUTPUT(29);
+	EFUSE_OUTPUT(30);
+	EFUSE_OUTPUT(31);
+	EFUSE_OUTPUT(32);
+	EFUSE_OUTPUT(33);
+	EFUSE_OUTPUT(34);
+	EFUSE_OUTPUT(35);
+	EFUSE_OUTPUT(36);
+	EFUSE_OUTPUT(37);
+	EFUSE_OUTPUT(38);
+	EFUSE_OUTPUT(39);
+	EFUSE_OUTPUT(40);
+	EFUSE_OUTPUT(41);
+	EFUSE_OUTPUT(42);
+	EFUSE_OUTPUT(43);
+	EFUSE_OUTPUT(44);
+	EFUSE_OUTPUT(45);
+	EFUSE_OUTPUT(46);
+	EFUSE_OUTPUT(47);
+	EFUSE_OUTPUT(48);
+	EFUSE_OUTPUT(49);
+	EFUSE_OUTPUT(50);
+
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "flash0";
+		spi-max-frequency = <50000000>; // 50 MHz
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c0 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@79 {
+		compatible = "nxp,pca9541";
+		reg = <0x79>;
+
+		i2carb0: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* lm25066 efuses @ 10-17, 40-47, 50-57 */
+			EFUSE(10, 03);
+			EFUSE(11, 04);
+			EFUSE(12, 01);
+			EFUSE(13, 02);
+			EFUSE(14, 13);
+			EFUSE(15, 14);
+			EFUSE(16, 15);
+			EFUSE(17, 16);
+			EFUSE(40, 12);
+			EFUSE(41, 11);
+			EFUSE(42, 10);
+			EFUSE(43, 09);
+			EFUSE(44, 08);
+			EFUSE(45, 07);
+			EFUSE(46, 05);
+			EFUSE(47, 06);
+			EFUSE(50, 17);
+			EFUSE(51, 18);
+			EFUSE(52, 20);
+			EFUSE(53, 19);
+			EFUSE(54, 22);
+			EFUSE(55, 21);
+			EFUSE(56, 24);
+			EFUSE(57, 23);
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@72 {
+		compatible = "nxp,pca9541";
+		reg = <0x72>;
+
+		i2carb1: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@73 {
+		compatible = "nxp,pca9541";
+		reg = <0x73>;
+
+		i2carb2: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@74 {
+		compatible = "nxp,pca9541";
+		reg = <0x74>;
+
+		i2carb3: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@7a {
+		compatible = "nxp,pca9541";
+		reg = <0x7a>;
+
+		i2carb4: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@20 {
+				compatible = "nxp,pca9534";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			/* lm25066 efuses @ 10-17, 40-47, 50-57, 59, 5a */
+			EFUSE(10, 27);
+			EFUSE(11, 28);
+			EFUSE(12, 25);
+			EFUSE(13, 26);
+			EFUSE(14, 37);
+			EFUSE(15, 38);
+			EFUSE(16, 39);
+			EFUSE(17, 40);
+			EFUSE(40, 36);
+			EFUSE(41, 35);
+			EFUSE(42, 34);
+			EFUSE(43, 33);
+			EFUSE(44, 32);
+			EFUSE(45, 31);
+			EFUSE(46, 29);
+			EFUSE(47, 30);
+			EFUSE(50, 41);
+			EFUSE(51, 42);
+			EFUSE(52, 44);
+			EFUSE(53, 43);
+			EFUSE(54, 46);
+			EFUSE(55, 45);
+			EFUSE(56, 48);
+			EFUSE(57, 47);
+			EFUSE(59, 49);
+			EFUSE(5a, 50);
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@75 {
+		compatible = "nxp,pca9541";
+		reg = <0x75>;
+
+		i2carb6: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@76 {
+		compatible = "nxp,pca9541";
+		reg = <0x76>;
+
+		i2carb7: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@7c {
+		compatible = "nxp,pca9541";
+		reg = <0x7c>;
+
+		i2carb8: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fancontrol@30 {
+				compatible = "delta,ahe50dc-fan";
+				reg = <0x30>;
+			};
+
+			/* Baseboard FRU eeprom */
+			eeprom@50 {
+				compatible = "atmel,24c02";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@71 {
+		compatible = "nxp,pca9541";
+		reg = <0x71>;
+
+		i2carb12: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "", "", "", "", "", "", "", "",
+		/*  B */ "", "", "", "", "", "", "", "",
+		/*  C */ "RESET_PEER_N", "HEARTBEAT_OUT", "", "", "", "", "", "",
+		/*  D */ "", "", "", "", "", "", "", "",
+		/*  E */ "DOOM_N", "", "", "", "", "LED_PWR_BLUE", "", "",
+		/*  F */ "", "", "", "", "", "", "", "",
+		/*  G */ "", "", "", "", "", "", "", "",
+		/*  H */ "", "", "", "", "", "", "", "",
+		/*  I */ "", "", "", "", "", "", "", "",
+		/*  J */ "", "", "BMC_ID", "", "", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "", "", "", "", "", "", "", "",
+		/*  M */ "", "", "", "", "", "", "", "",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "LED_GREEN", "", "LED_RED", "", "", "", "", "",
+		/*  Q */ "", "", "", "", "", "", "", "",
+		/*  R */ "", "", "", "", "", "", "", "",
+		/*  S */ "", "", "", "", "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "", "", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "HEARTBEAT_IN", "BOARDREV0", "BOARDREV1", "",
+		/*  Z */ "", "", "", "", "", "", "", "",
+		/* AA */ "", "", "", "", "", "", "", "",
+		/* AB */ "", "", "", "";
+
+	/*
+	 * I don't rightly know what this GPIO really *is*, but setting it to
+	 * zero causes the fans to run at full speed, after which setting it
+	 * back to one causes a power output glitch, so install a hog to keep
+	 * it at one as a failsafe to ensure nothing accidentally touches it.
+	 */
+	doom-guardrail {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(E, 0) GPIO_ACTIVE_LOW>;
+		output-low;
+	};
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
new file mode 100644
index 000000000000..e899de681f47
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
@@ -0,0 +1,1077 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Bletchley BMC";
+	compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		bootargs = "console=ttyS4,57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			<&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	spi1_gpio: spi1-gpio {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+
+		tpmdev@0 {
+			compatible = "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+
+	switchphy: ethernet-phy@0 {
+		// Fixed link
+	};
+
+	front_gpio_leds {
+		compatible = "gpio-leds";
+		sys_log_id {
+			default-state = "off";
+			gpios = <&front_leds 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	fan_gpio_leds {
+		compatible = "gpio-leds";
+		fan0_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 8 GPIO_ACTIVE_HIGH>;
+		};
+		fan1_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 9 GPIO_ACTIVE_HIGH>;
+		};
+		fan2_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 10 GPIO_ACTIVE_HIGH>;
+		};
+		fan3_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 11 GPIO_ACTIVE_HIGH>;
+		};
+		fan0_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 12 GPIO_ACTIVE_HIGH>;
+		};
+		fan1_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 13 GPIO_ACTIVE_HIGH>;
+		};
+		fan2_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 14 GPIO_ACTIVE_HIGH>;
+		};
+		fan3_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sled1_gpio_leds {
+		compatible = "gpio-leds";
+		sled1_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled1_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled2_gpio_leds {
+		compatible = "gpio-leds";
+		sled2_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled2_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled3_gpio_leds {
+		compatible = "gpio-leds";
+		sled3_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled3_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled4_gpio_leds {
+		compatible = "gpio-leds";
+		sled4_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled4_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled5_gpio_leds {
+		compatible = "gpio-leds";
+		sled5_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled5_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled6_gpio_leds {
+		compatible = "gpio-leds";
+		sled6_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled6_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		presence-sled1 {
+			label = "presence-sled1";
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 2)>;
+		};
+		presence-sled2 {
+			label = "presence-sled2";
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 3)>;
+		};
+		presence-sled3 {
+			label = "presence-sled3";
+			gpios = <&gpio0 ASPEED_GPIO(H, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 4)>;
+		};
+		presence-sled4 {
+			label = "presence-sled4";
+			gpios = <&gpio0 ASPEED_GPIO(H, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 5)>;
+		};
+		presence-sled5 {
+			label = "presence-sled5";
+			gpios = <&gpio0 ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 6)>;
+		};
+		presence-sled6 {
+			label = "presence-sled6";
+			gpios = <&gpio0 ASPEED_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 7)>;
+		};
+	};
+
+	vbus_sled1: vbus_sled1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled1_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled2: vbus_sled2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled2_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled3: vbus_sled3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled3";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled3_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled4: vbus_sled4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled4";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled4_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled5: vbus_sled5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled5";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled5_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled6: vbus_sled6 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled6";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled6_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&mac2 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&switchphy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled1_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED1_SWD_MUX", "SLED1_XRES_SWD_N",
+		"SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN";
+	};
+
+	sled1_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+		"SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+		"SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+		"SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+	};
+
+	sled1_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled1_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(B, 0) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled1>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "source";
+			data-role = "host";
+			pd-disable;
+			typec-power-opmode = "default";
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled2_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
+		"SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
+	};
+
+	sled2_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
+		"SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
+		"SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
+		"SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
+	};
+
+	sled2_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled2_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(B, 1) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled2>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "source";
+			data-role = "host";
+			pd-disable;
+			typec-power-opmode = "default";
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled3_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
+		"SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
+	};
+
+	sled3_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
+		"SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
+		"SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
+		"SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
+	};
+
+	sled3_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled3_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(B, 7) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled3>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "source";
+			data-role = "host";
+			pd-disable;
+			typec-power-opmode = "default";
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled4_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
+		"SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
+	};
+
+	sled4_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
+		"SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
+		"SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
+		"SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
+	};
+
+	sled4_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled4_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(S, 7) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled4>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "source";
+			data-role = "host";
+			pd-disable;
+			typec-power-opmode = "default";
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled5_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
+		"SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
+	};
+
+	sled5_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
+		"SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
+		"SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
+		"SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
+	};
+
+	sled5_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled5_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(Y, 3) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled5>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "source";
+			data-role = "host";
+			pd-disable;
+			typec-power-opmode = "default";
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled6_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED6_SWD_MUX", "SLED6_XRES_SWD_N",
+		"SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN";
+	};
+
+	sled6_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
+		"SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
+		"SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
+		"SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
+	};
+
+	sled6_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled6_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 7) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled6>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "source";
+			data-role = "host";
+			pd-disable;
+			typec-power-opmode = "default";
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+
+	rtc@51 {
+		/* in-chip rtc disabled, use external rtc (battery-backed) */
+		compatible = "nxp,pcf85263";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	front_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-fault-identify","power-p5v-stby-good",
+		"power-p1v0-dvdd-good","power-p1v0-avdd-good",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	adm1278@11 {
+		compatible = "adi,adm1278";
+		reg = <0x11>;
+		shunt-resistor-micro-ohms = <300>;
+		adi,volt-curr-sample-average = <128>;
+		adi,power-sample-average = <128>;
+	};
+
+	tmp421@4c {
+		compatible = "ti,tmp421";
+		reg = <0x4c>;
+	};
+
+	tmp421@4d {
+		compatible = "ti,tmp421";
+		reg = <0x4d>;
+	};
+
+	fan_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"presence-fan0","presence-fan1",
+		"presence-fan2","presence-fan3",
+		"power-fan0-good","power-fan1-good",
+		"power-fan2-good","power-fan3-good",
+		"","","","",
+		"","","","";
+	};
+};
+
+&i2c13 {
+	multi-master;
+	aspeed,hw-timeout-ms = <1000>;
+	status = "okay";
+
+	//USB Debug Connector
+	ipmb13@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiov2_unbiased_default>;
+
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"FUSB302_SLED1_INT_N","FUSB302_SLED2_INT_N",
+			"SEL_SPI2_MUX","SPI2_MUX1",
+			"SPI2_MUX2","SPI2_MUX3",
+			"","FUSB302_SLED3_INT_N",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"BMC_SLED1_STCK","BMC_SLED2_STCK",
+			"BMC_SLED3_STCK","BMC_SLED4_STCK",
+			"BMC_SLED5_STCK","BMC_SLED6_STCK",
+			"","",
+	/*G0-G7*/	"BSM_FRU_WP","SWITCH_FRU_MUX","","FM_SOL_UART_CH_SEL",
+			"PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
+	/*H0-H7*/	"presence-riser1","presence-riser2",
+			"presence-sled1","presence-sled2",
+			"presence-sled3","presence-sled4",
+			"presence-sled5","presence-sled6",
+	/*I0-I7*/	"REV_ID0","",
+			"REV_ID1","REV_ID2",
+			"","BSM_FLASH_WP_STATUS",
+			"BMC_TPM_PRES_N","FUSB302_SLED6_INT_N",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","BMC_RTC_INT","","",
+	/*M0-M7*/	"ALERT_SLED1_N","ALERT_SLED2_N",
+			"ALERT_SLED3_N","ALERT_SLED4_N",
+			"ALERT_SLED5_N","ALERT_SLED6_N",
+			"","USB_DEBUG_PWR_BTN_N",
+	/*N0-N7*/	"LED_POSTCODE_0","LED_POSTCODE_1",
+			"LED_POSTCODE_2","LED_POSTCODE_3",
+			"LED_POSTCODE_4","LED_POSTCODE_5",
+			"LED_POSTCODE_6","LED_POSTCODE_7",
+	/*O0-O7*/	"","","","",
+			"","BOARD_ID0","BOARD_ID1","BOARD_ID2",
+	/*P0-P7*/	"","","","","","","","BMC_HEARTBEAT",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","BAT_DETECT",
+			"BMC_BT_WP0_N","BMC_BT_WP1_N","","FUSB302_SLED4_INT_N",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"PWRGD_CNS_PSU","RST_BMC_MVL_N",
+			"P12V_AUX_ALERT1_N","PSU_PRSNT",
+			"USB2_SEL0_A","USB2_SEL1_A",
+			"USB2_SEL0_B","USB2_SEL1_B",
+	/*W0-W7*/	"RST_FRONT_IOEXP_N","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"BMC_SELF_HW_RST","BSM_PRSNT_N",
+			"BSM_FLASH_LATCH_N","FUSB302_SLED5_INT_N",
+			"","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+};
+
+&adc0 {
+	vref = <1800>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&mdio0 {
+	status = "okay";
+	/* TODO: Add Marvell 88E6191X */
+};
+
+&mdio3 {
+	status = "okay";
+	/* TODO: Add Marvell 88X3310 */
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl_gpiov2_unbiased_default: gpiov2 {
+		pins = "AD14";
+		bias-disable;
+	};
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cloudripper.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cloudripper.dts
new file mode 100644
index 000000000000..d49328fa487a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cloudripper.dts
@@ -0,0 +1,544 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Cloudripper BMC";
+	compatible = "facebook,cloudripper-bmc", "aspeed,ast2600";
+
+	aliases {
+		/*
+		 * PCA9548 (1-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * PCA9548 (2-0070) provides 8 channels connecting to
+		 * SCM (System Controller Module).
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		/*
+		 * PCA9548 (3-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
+		i2c38 = &imux38;
+		i2c39 = &imux39;
+
+		/*
+		 * PCA9548 (8-0070) provides 8 channels connecting to
+		 * PDB (Power Delivery Board).
+		 */
+		i2c40 = &imux40;
+		i2c41 = &imux41;
+		i2c42 = &imux42;
+		i2c43 = &imux43;
+		i2c44 = &imux44;
+		i2c45 = &imux45;
+		i2c46 = &imux46;
+		i2c47 = &imux47;
+
+		/*
+		 * PCA9548 (15-0076) provides 8 channels connecting to
+		 * FCM (Fan Controller Module).
+		 */
+		i2c48 = &imux48;
+		i2c49 = &imux49;
+		i2c50 = &imux50;
+		i2c51 = &imux51;
+		i2c52 = &imux52;
+		i2c53 = &imux53;
+		i2c54 = &imux54;
+		i2c55 = &imux55;
+	};
+
+	spi_gpio: spi {
+		num-chipselects = <2>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
+			   <&gpio0 ASPEED_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+
+		eeprom@1 {
+			compatible = "atmel,at93c46d";
+			spi-max-frequency = <250000>;
+			data-size = <16>;
+			spi-cs-high;
+			reg = <1>;
+		};
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+/*
+ * "mdio1" is connected to the MDC/MDIO interface of the on-board
+ * management switch (whose ports are connected to BMC, Host and front
+ * panel ethernet port).
+ */
+&mdio1 {
+	status = "okay";
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@13 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0d>;
+	};
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&i2c0 {
+	multi-master;
+	bus-frequency = <1000000>;
+};
+
+&i2c1 {
+	/*
+	 * PCA9548 (1-0070) provides 8 channels connecting to SMB (Switch
+	 * Main Board).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c2 {
+	/*
+	 * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
+	 * Controller Module).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c3 {
+	/*
+	 * PCA9548 (3-0070) provides 8 channels connecting to SMB (Switch
+	 * Main Board).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux36: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux37: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux38: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux39: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c6 {
+	lp5012@14 {
+		compatible = "ti,lp5012";
+		reg = <0x14>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		multi-led@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "sys";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+
+		multi-led@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "fan";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+
+		multi-led@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "psu";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+
+		multi-led@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "scm";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+	};
+};
+
+&i2c8 {
+	/*
+	 * PCA9548 (8-0070) provides 8 channels connecting to PDB (Power
+	 * Delivery Board).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux40: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux41: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux42: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux43: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux44: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux45: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux46: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux47: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+	};
+};
+
+&i2c15 {
+	/*
+	 * PCA9548 (15-0076) provides 8 channels connecting to FCM (Fan
+	 * Controller Module).
+	 */
+	i2c-mux@76 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x76>;
+		i2c-mux-idle-disconnect;
+
+		imux48: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux49: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux50: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux51: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux52: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux53: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux54: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux55: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cmm.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cmm.dts
new file mode 100644
index 000000000000..24153868cc00
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cmm.dts
@@ -0,0 +1,1590 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Facebook Inc.
+/dts-v1/;
+
+#include "ast2500-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Backpack CMM BMC";
+	compatible = "facebook,cmm-bmc", "aspeed,ast2500";
+
+	aliases {
+		/*
+		 * Override the default uart aliases to avoid breaking
+		 * the legacy applications.
+		 */
+		serial0 = &uart5;
+		serial1 = &uart1;
+		serial2 = &uart3;
+		serial3 = &uart4;
+
+		/*
+		 * PCA9548 (1-0077) provides 8 channels for connecting to
+		 * 4 Line Cards and 4 Fabric Cards.
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * PCA9548 (2-0071) provides 8 channels for connecting to
+		 * Power Distribution Board.
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		/*
+		 * PCA9548 (8-0077) provides 8 channels and the first 4
+		 * channels are connecting to 4 Fan Control Boards.
+		 */
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
+		i2c38 = &imux38;
+		i2c39 = &imux39;
+
+		/*
+		 * 2 PCA9548 (18-0070 & 18-0073), 16 channels connecting
+		 * to Line Card #1.
+		 */
+		i2c40 = &imux40;
+		i2c41 = &imux41;
+		i2c42 = &imux42;
+		i2c43 = &imux43;
+		i2c44 = &imux44;
+		i2c45 = &imux45;
+		i2c46 = &imux46;
+		i2c47 = &imux47;
+		i2c48 = &imux48;
+		i2c49 = &imux49;
+		i2c50 = &imux50;
+		i2c51 = &imux51;
+		i2c52 = &imux52;
+		i2c53 = &imux53;
+		i2c54 = &imux54;
+		i2c55 = &imux55;
+
+		/*
+		 * 2 PCA9548 (19-0070 & 19-0073), 16 channels connecting
+		 * to Line Card #2.
+		 */
+		i2c56 = &imux56;
+		i2c57 = &imux57;
+		i2c58 = &imux58;
+		i2c59 = &imux59;
+		i2c60 = &imux60;
+		i2c61 = &imux61;
+		i2c62 = &imux62;
+		i2c63 = &imux63;
+		i2c64 = &imux64;
+		i2c65 = &imux65;
+		i2c66 = &imux66;
+		i2c67 = &imux67;
+		i2c68 = &imux68;
+		i2c69 = &imux69;
+		i2c70 = &imux70;
+		i2c71 = &imux71;
+
+		/*
+		 * 2 PCA9548 (20-0070 & 20-0073), 16 channels connecting
+		 * to Line Card #3.
+		 */
+		i2c72 = &imux72;
+		i2c73 = &imux73;
+		i2c74 = &imux74;
+		i2c75 = &imux75;
+		i2c76 = &imux76;
+		i2c77 = &imux77;
+		i2c78 = &imux78;
+		i2c79 = &imux79;
+		i2c80 = &imux80;
+		i2c81 = &imux81;
+		i2c82 = &imux82;
+		i2c83 = &imux83;
+		i2c84 = &imux84;
+		i2c85 = &imux85;
+		i2c86 = &imux86;
+		i2c87 = &imux87;
+
+		/*
+		 * 2 PCA9548 (21-0070 & 21-0073), 16 channels connecting
+		 * to Line Card #4.
+		 */
+		i2c88 = &imux88;
+		i2c89 = &imux89;
+		i2c90 = &imux90;
+		i2c91 = &imux91;
+		i2c92 = &imux92;
+		i2c93 = &imux93;
+		i2c94 = &imux94;
+		i2c95 = &imux95;
+		i2c96 = &imux96;
+		i2c97 = &imux97;
+		i2c98 = &imux98;
+		i2c99 = &imux99;
+		i2c100 = &imux100;
+		i2c101 = &imux101;
+		i2c102 = &imux102;
+		i2c103 = &imux103;
+
+		/*
+		 * 2 PCA9548 (16-0070 & 16-0073), 16 channels connecting
+		 * to Fabric Card #1.
+		 */
+		i2c104 = &imux104;
+		i2c105 = &imux105;
+		i2c106 = &imux106;
+		i2c107 = &imux107;
+		i2c108 = &imux108;
+		i2c109 = &imux109;
+		i2c110 = &imux110;
+		i2c111 = &imux111;
+		i2c112 = &imux112;
+		i2c113 = &imux113;
+		i2c114 = &imux114;
+		i2c115 = &imux115;
+		i2c116 = &imux116;
+		i2c117 = &imux117;
+		i2c118 = &imux118;
+		i2c119 = &imux119;
+
+		/*
+		 * 2 PCA9548 (17-0070 & 17-0073), 16 channels connecting
+		 * to Fabric Card #2.
+		 */
+		i2c120 = &imux120;
+		i2c121 = &imux121;
+		i2c122 = &imux122;
+		i2c123 = &imux123;
+		i2c124 = &imux124;
+		i2c125 = &imux125;
+		i2c126 = &imux126;
+		i2c127 = &imux127;
+		i2c128 = &imux128;
+		i2c129 = &imux129;
+		i2c130 = &imux130;
+		i2c131 = &imux131;
+		i2c132 = &imux132;
+		i2c133 = &imux133;
+		i2c134 = &imux134;
+		i2c135 = &imux135;
+
+		/*
+		 * 2 PCA9548 (22-0070 & 22-0073), 16 channels connecting
+		 * to Fabric Card #3.
+		 */
+		i2c136 = &imux136;
+		i2c137 = &imux137;
+		i2c138 = &imux138;
+		i2c139 = &imux139;
+		i2c140 = &imux140;
+		i2c141 = &imux141;
+		i2c142 = &imux142;
+		i2c143 = &imux143;
+		i2c144 = &imux144;
+		i2c145 = &imux145;
+		i2c146 = &imux146;
+		i2c147 = &imux147;
+		i2c148 = &imux148;
+		i2c149 = &imux149;
+		i2c150 = &imux150;
+		i2c151 = &imux151;
+
+		/*
+		 * 2 PCA9548 (23-0070 & 23-0073), 16 channels connecting
+		 * to Fabric Card #4.
+		 */
+		i2c152 = &imux152;
+		i2c153 = &imux153;
+		i2c154 = &imux154;
+		i2c155 = &imux155;
+		i2c156 = &imux156;
+		i2c157 = &imux157;
+		i2c158 = &imux158;
+		i2c159 = &imux159;
+		i2c160 = &imux160;
+		i2c161 = &imux161;
+		i2c162 = &imux162;
+		i2c163 = &imux163;
+		i2c164 = &imux164;
+		i2c165 = &imux165;
+		i2c166 = &imux166;
+		i2c167 = &imux167;
+
+		/*
+		 * PCA9548 (32-0070), 8 channels connecting to Fan Control
+		 # Board #1.
+		 */
+		i2c168 = &imux168;
+		i2c169 = &imux169;
+		i2c170 = &imux170;
+		i2c171 = &imux171;
+		i2c172 = &imux172;
+		i2c173 = &imux173;
+		i2c174 = &imux174;
+		i2c175 = &imux175;
+
+		/*
+		 * PCA9548 (33-0070), 8 channels connecting to Fan Control
+		 # Board #2.
+		 */
+		i2c176 = &imux176;
+		i2c177 = &imux177;
+		i2c178 = &imux178;
+		i2c179 = &imux179;
+		i2c180 = &imux180;
+		i2c181 = &imux181;
+		i2c182 = &imux182;
+		i2c183 = &imux183;
+
+		/*
+		 * PCA9548 (34-0070), 8 channels connecting to Fan Control
+		 # Board #3.
+		 */
+		i2c184 = &imux184;
+		i2c185 = &imux185;
+		i2c186 = &imux186;
+		i2c187 = &imux187;
+		i2c188 = &imux188;
+		i2c189 = &imux189;
+		i2c190 = &imux190;
+		i2c191 = &imux191;
+
+		/*
+		 * PCA9548 (35-0070), 8 channels connecting to Fan Control
+		 # Board #4.
+		 */
+		i2c192 = &imux192;
+		i2c193 = &imux193;
+		i2c194 = &imux194;
+		i2c195 = &imux195;
+		i2c196 = &imux196;
+		i2c197 = &imux197;
+		i2c198 = &imux198;
+		i2c199 = &imux199;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+		bootargs = "console=ttyS1,9600n8 root=/dev/ram rw earlycon";
+	};
+
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			      <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>;
+	};
+};
+
+&uart1 {
+	pinctrl-0 = <&pinctrl_txd1_default
+		     &pinctrl_rxd1_default
+		     &pinctrl_ncts1_default
+		     &pinctrl_ndcd1_default
+		     &pinctrl_ndsr1_default
+		     &pinctrl_ndtr1_default
+		     &pinctrl_nrts1_default>;
+};
+
+&uart3 {
+	pinctrl-0 = <&pinctrl_txd3_default
+		     &pinctrl_rxd3_default
+		     &pinctrl_ncts3_default
+		     &pinctrl_ndcd3_default
+		     &pinctrl_nri3_default>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd4_default
+		     &pinctrl_rxd4_default>;
+};
+
+/*
+ * I2C bus reserved for communication with COM-E.
+ */
+&i2c0 {
+	status = "okay";
+};
+
+/*
+ * I2C bus to Line Cards and Fabric Cards.
+ */
+&i2c1 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		/* To Fabric Card #1 */
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux104: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux105: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux106: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux107: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux108: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux109: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux110: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux111: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux112: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux113: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux114: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux115: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux116: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux117: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux118: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux119: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Fabric Card #2 */
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux120: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux121: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux122: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux123: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux124: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux125: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux126: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux127: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux128: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux129: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux130: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux131: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux132: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux133: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux134: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux135: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Line Card #1 */
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux40: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux41: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux42: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux43: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux44: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux45: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux46: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux47: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux48: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux49: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux50: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux51: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux52: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux53: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux54: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux55: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Line Card #2 */
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux56: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux57: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux58: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux59: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux60: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux61: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux62: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux63: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux64: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux65: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux66: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux67: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux68: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux69: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux70: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux71: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To LC3 SCM */
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux72: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux73: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux74: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux75: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux76: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux77: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux78: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux79: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux80: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux81: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux82: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux83: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux84: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux85: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux86: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux87: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Line Card #4 */
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux88: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux89: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux90: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux91: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux92: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux93: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux94: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux95: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux96: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux97: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux98: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux99: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux100: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux101: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux102: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux103: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Fabric Card #3 */
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux136: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux137: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux138: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux139: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux140: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux141: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux142: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux143: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux144: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux145: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux146: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux147: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux148: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux149: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux150: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux151: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Fabric Card #4 */
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux152: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux153: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux154: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux155: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux156: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux157: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux158: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux159: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux160: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux161: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux162: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux163: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux164: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux165: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux166: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux167: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+	};
+};
+
+/*
+ * I2C bus to Power Distribution Board.
+ */
+&i2c2 {
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/*
+ * I2c bus connected with temperature sensors on CMM.
+ */
+&i2c3 {
+	status = "okay";
+};
+
+/*
+ * I2C bus reserved for communication with COM-E.
+ */
+&i2c4 {
+	status = "okay";
+};
+
+/*
+ * I2c bus connected with ADM1278.
+ */
+&i2c5 {
+	status = "okay";
+};
+
+/*
+ * I2c bus connected with I/O Expander.
+ */
+&i2c6 {
+	status = "okay";
+};
+
+/*
+ * I2c bus connected with I/O Expander and EPROMs.
+ */
+&i2c7 {
+	status = "okay";
+};
+
+/*
+ * I2C bus to Fan Control Boards.
+ */
+&i2c8 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		/* To Fan Control Board #1 */
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux168: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux169: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux170: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux171: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux172: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux173: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux174: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux175: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Fan Control Board #2 */
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux176: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux177: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux178: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux179: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux180: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux181: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux182: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux183: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Fan Control Board #3 */
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux184: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux185: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux186: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux187: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux188: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux189: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux190: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux191: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/* To Fan Control Board #4 */
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+
+				imux192: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+				imux193: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+				imux194: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+				imux195: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+				imux196: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+				imux197: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+				imux198: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+				imux199: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		imux36: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux37: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux38: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux39: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/*
+ * I2C bus to CMM CPLD.
+ */
+&i2c13 {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&vhub {
+	status = "disabled";
+};
+
+&sdhci0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sd1_default>;
+};
+
+&sdhci1 {
+	status = "disabled";
+};
+
+&fmc_flash0 {
+#include "facebook-bmc-flash-layout.dtsi"
+};
+
+&fmc_flash1 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		flash1@0 {
+			reg = <0x0 0x2000000>;
+			label = "flash1";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts
new file mode 100644
index 000000000000..74f3c67e0eff
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Elbert BMC";
+	compatible = "facebook,elbert-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+
+		/*
+		 * 8 child channels of PCA9548 2-0075.
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * 8 child channels of PCA9548 5-0075.
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	spi_gpio: spi {
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+	};
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&i2c2 {
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c5 {
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+/*
+ * BMC's "mac3" controller is connected to BCM53134P's IMP_RGMII port
+ * directly (fixed link, no PHY in between).
+ * Note: BMC's "mdio0" controller is connected to BCM53134P's MDIO
+ * interface, and the MDIO channel will be enabled in dts later, when
+ * BCM53134 is added to "bcm53xx" DSA driver.
+ */
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts
new file mode 100644
index 000000000000..f23c26a3441d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts
@@ -0,0 +1,1251 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Fuji BMC";
+	compatible = "facebook,fuji-bmc", "aspeed,ast2600";
+
+	aliases {
+		/*
+		 * PCA9548 (2-0070) provides 8 channels connecting to
+		 * SCM (System Controller Module).
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * PCA9548 (8-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		/*
+		 * PCA9548 (11-0077) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c40 = &imux40;
+		i2c41 = &imux41;
+		i2c42 = &imux42;
+		i2c43 = &imux43;
+		i2c44 = &imux44;
+		i2c45 = &imux45;
+		i2c46 = &imux46;
+		i2c47 = &imux47;
+
+		/*
+		 * PCA9548 (24-0071) provides 8 channels connecting to
+		 * PDB-Left.
+		 */
+		i2c48 = &imux48;
+		i2c49 = &imux49;
+		i2c50 = &imux50;
+		i2c51 = &imux51;
+		i2c52 = &imux52;
+		i2c53 = &imux53;
+		i2c54 = &imux54;
+		i2c55 = &imux55;
+
+		/*
+		 * PCA9548 (25-0072) provides 8 channels connecting to
+		 * PDB-Right.
+		 */
+		i2c56 = &imux56;
+		i2c57 = &imux57;
+		i2c58 = &imux58;
+		i2c59 = &imux59;
+		i2c60 = &imux60;
+		i2c61 = &imux61;
+		i2c62 = &imux62;
+		i2c63 = &imux63;
+
+		/*
+		 * PCA9548 (26-0076) provides 8 channels connecting to
+		 * FCM1.
+		 */
+		i2c64 = &imux64;
+		i2c65 = &imux65;
+		i2c66 = &imux66;
+		i2c67 = &imux67;
+		i2c68 = &imux68;
+		i2c69 = &imux69;
+		i2c70 = &imux70;
+		i2c71 = &imux71;
+
+		/*
+		 * PCA9548 (27-0076) provides 8 channels connecting to
+		 * FCM2.
+		 */
+		i2c72 = &imux72;
+		i2c73 = &imux73;
+		i2c74 = &imux74;
+		i2c75 = &imux75;
+		i2c76 = &imux76;
+		i2c77 = &imux77;
+		i2c78 = &imux78;
+		i2c79 = &imux79;
+
+		/*
+		 * PCA9548 (40-0076) provides 8 channels connecting to
+		 * PIM1.
+		 */
+		i2c80 = &imux80;
+		i2c81 = &imux81;
+		i2c82 = &imux82;
+		i2c83 = &imux83;
+		i2c84 = &imux84;
+		i2c85 = &imux85;
+		i2c86 = &imux86;
+		i2c87 = &imux87;
+
+		/*
+		 * PCA9548 (41-0076) provides 8 channels connecting to
+		 * PIM2.
+		 */
+		i2c88 = &imux88;
+		i2c89 = &imux89;
+		i2c90 = &imux90;
+		i2c91 = &imux91;
+		i2c92 = &imux92;
+		i2c93 = &imux93;
+		i2c94 = &imux94;
+		i2c95 = &imux95;
+
+		/*
+		 * PCA9548 (42-0076) provides 8 channels connecting to
+		 * PIM3.
+		 */
+		i2c96 = &imux96;
+		i2c97 = &imux97;
+		i2c98 = &imux98;
+		i2c99 = &imux99;
+		i2c100 = &imux100;
+		i2c101 = &imux101;
+		i2c102 = &imux102;
+		i2c103 = &imux103;
+
+		/*
+		 * PCA9548 (43-0076) provides 8 channels connecting to
+		 * PIM4.
+		 */
+		i2c104 = &imux104;
+		i2c105 = &imux105;
+		i2c106 = &imux106;
+		i2c107 = &imux107;
+		i2c108 = &imux108;
+		i2c109 = &imux109;
+		i2c110 = &imux110;
+		i2c111 = &imux111;
+
+		/*
+		 * PCA9548 (44-0076) provides 8 channels connecting to
+		 * PIM5.
+		 */
+		i2c112 = &imux112;
+		i2c113 = &imux113;
+		i2c114 = &imux114;
+		i2c115 = &imux115;
+		i2c116 = &imux116;
+		i2c117 = &imux117;
+		i2c118 = &imux118;
+		i2c119 = &imux119;
+
+		/*
+		 * PCA9548 (45-0076) provides 8 channels connecting to
+		 * PIM6.
+		 */
+		i2c120 = &imux120;
+		i2c121 = &imux121;
+		i2c122 = &imux122;
+		i2c123 = &imux123;
+		i2c124 = &imux124;
+		i2c125 = &imux125;
+		i2c126 = &imux126;
+		i2c127 = &imux127;
+
+		/*
+		 * PCA9548 (46-0076) provides 8 channels connecting to
+		 * PIM7.
+		 */
+		i2c128 = &imux128;
+		i2c129 = &imux129;
+		i2c130 = &imux130;
+		i2c131 = &imux131;
+		i2c132 = &imux132;
+		i2c133 = &imux133;
+		i2c134 = &imux134;
+		i2c135 = &imux135;
+
+		/*
+		 * PCA9548 (47-0076) provides 8 channels connecting to
+		 * PIM8.
+		 */
+		i2c136 = &imux136;
+		i2c137 = &imux137;
+		i2c138 = &imux138;
+		i2c139 = &imux139;
+		i2c140 = &imux140;
+		i2c141 = &imux141;
+		i2c142 = &imux142;
+		i2c143 = &imux143;
+	};
+
+	spi_gpio: spi {
+		num-chipselects = <3>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
+			   <0>,	/* device reg=<1> does not exist */
+			   <&gpio0 ASPEED_GPIO(X, 2) GPIO_ACTIVE_HIGH>;
+
+		eeprom@2 {
+			compatible = "atmel,at93c46d";
+			spi-max-frequency = <250000>;
+			data-size = <16>;
+			spi-cs-high;
+			reg = <2>;
+		};
+	};
+};
+
+&i2c0 {
+	multi-master;
+	bus-frequency = <1000000>;
+};
+
+&i2c2 {
+	/*
+	 * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
+	 * Controller Module).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adm1278@10 {
+				compatible = "adi,adm1278";
+				reg = <0x10>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				shunt-resistor-micro-ohms = <1500>;
+			};
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c8 {
+	/*
+	 * PCA9548 (8-0070) provides 8 channels connecting to SMB (Switch
+	 * Main Board).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				imux48: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux49: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux50: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+
+					lp5012@14 {
+						compatible = "ti,lp5012";
+						reg = <0x14>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						multi-led@0 {
+							#address-cells = <1>;
+							#size-cells = <0>;
+							reg = <0>;
+							color = <LED_COLOR_ID_MULTI>;
+							function = LED_FUNCTION_ACTIVITY;
+							label = "sys";
+
+							led@0 {
+								reg = <0>;
+								color = <LED_COLOR_ID_RED>;
+							};
+
+							led@1 {
+								reg = <1>;
+								color = <LED_COLOR_ID_BLUE>;
+							};
+
+							led@2 {
+								reg = <2>;
+								color = <LED_COLOR_ID_GREEN>;
+							};
+						};
+
+						multi-led@1 {
+							#address-cells = <1>;
+							#size-cells = <0>;
+							reg = <1>;
+							color = <LED_COLOR_ID_MULTI>;
+							function = LED_FUNCTION_ACTIVITY;
+							label = "fan";
+
+							led@0 {
+								reg = <0>;
+								color = <LED_COLOR_ID_RED>;
+							};
+
+							led@1 {
+								reg = <1>;
+								color = <LED_COLOR_ID_BLUE>;
+							};
+
+							led@2 {
+								reg = <2>;
+								color = <LED_COLOR_ID_GREEN>;
+							};
+						};
+
+						multi-led@2 {
+							#address-cells = <1>;
+							#size-cells = <0>;
+							reg = <2>;
+							color = <LED_COLOR_ID_MULTI>;
+							function = LED_FUNCTION_ACTIVITY;
+							label = "psu";
+
+							led@0 {
+								reg = <0>;
+								color = <LED_COLOR_ID_RED>;
+							};
+
+							led@1 {
+								reg = <1>;
+								color = <LED_COLOR_ID_BLUE>;
+							};
+
+							led@2 {
+								reg = <2>;
+								color = <LED_COLOR_ID_GREEN>;
+							};
+						};
+
+						multi-led@3 {
+							#address-cells = <1>;
+							#size-cells = <0>;
+							reg = <3>;
+							color = <LED_COLOR_ID_MULTI>;
+							function = LED_FUNCTION_ACTIVITY;
+							label = "smb";
+
+							led@0 {
+								reg = <0>;
+								color = <LED_COLOR_ID_RED>;
+							};
+
+							led@1 {
+								reg = <1>;
+								color = <LED_COLOR_ID_BLUE>;
+							};
+
+							led@2 {
+								reg = <2>;
+								color = <LED_COLOR_ID_GREEN>;
+							};
+						};
+					};
+				};
+
+				imux51: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux52: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux53: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux54: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux55: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@72 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72>;
+				i2c-mux-idle-disconnect;
+
+				imux56: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux57: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux58: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux59: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux60: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux61: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux62: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux63: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux64: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux65: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux66: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux67: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+
+					adm1278@10 {
+						compatible = "adi,adm1278";
+						reg = <0x10>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						shunt-resistor-micro-ohms = <250>;
+					};
+				};
+
+				imux68: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux69: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux70: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux71: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux72: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux73: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux74: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux75: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+
+					adm1278@10 {
+						compatible = "adi,adm1278";
+						reg = <0x10>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						shunt-resistor-micro-ohms = <250>;
+					};
+				};
+
+				imux76: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux77: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux78: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux79: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	/*
+	 * PCA9548 (11-0077) provides 8 channels connecting to SMB (Switch
+	 * Main Board).
+	 */
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		imux40: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux80: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux81: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux82: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux83: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux84: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux85: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux86: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux87: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux41: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux88: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux89: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux90: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux91: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux92: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux93: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux94: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux95: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux42: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux96: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux97: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux98: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux99: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux100: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux101: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux102: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux103: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux43: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux104: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux105: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux106: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux107: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux108: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux109: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux110: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux111: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux44: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux112: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux113: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux114: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux115: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux116: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux117: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux118: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux119: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux45: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux120: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux121: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux122: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux123: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux124: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux125: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux126: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux127: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux46: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux128: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux129: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux130: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux131: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux132: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux133: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux134: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux135: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+		imux47: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux136: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux137: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux138: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux139: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux140: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux141: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux142: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux143: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+
+		};
+
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mdio1 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@13 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0d>;
+	};
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-galaxy100.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-galaxy100.dts
new file mode 100644
index 000000000000..60e875ac2461
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-galaxy100.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+/dts-v1/;
+
+#include "ast2400-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Galaxy 100 BMC";
+	compatible = "facebook,galaxy100-bmc", "aspeed,ast2400";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS0,9600n8 root=/dev/ram rw";
+	};
+
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 3>, <&adc 4>, <&adc 8>, <&adc 9>;
+	};
+};
+
+&wdt2 {
+	status = "okay";
+	aspeed,reset-type = "system";
+};
+
+&fmc {
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "spi0.1";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash1@0 {
+				reg = <0x0 0x2000000>;
+				label = "flash1";
+			};
+		};
+	};
+};
+
+
+&i2c9 {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
new file mode 100644
index 000000000000..7a53f54833a0
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 Facebook Inc.
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Greatlakes BMC";
+	compatible = "facebook,greatlakes-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+				<&adc1 0>, <&adc1 2>, <&adc1 3>, <&adc1 4>,
+				<&adc1 5>, <&adc1 6>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	no-hw-checksum;
+	use-ncsi;
+	mlx,multi-host;
+	ncsi-ctrl,start-redo-probe;
+	ncsi-ctrl,no-channel-monitor;
+	ncsi-package = <1>;
+	ncsi-channel = <1>;
+	ncsi-rexmit = <1>;
+	ncsi-timeout = <2>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc2";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+	mctp-controller;
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+	// NIC EEPROM
+	eeprom@50 {
+		compatible = "st,24c32";
+		reg = <0x50>;
+	};
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	temperature-sensor@4f {
+		compatible = "lm75";
+		reg = <0x4f>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+			&pinctrl_adc2_default &pinctrl_adc3_default
+			&pinctrl_adc4_default &pinctrl_adc5_default
+			&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc10_default
+			&pinctrl_adc11_default &pinctrl_adc12_default
+			&pinctrl_adc13_default &pinctrl_adc14_default>;
+};
+
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiu1_default &pinctrl_gpiu7_default>;
+
+	gpio-line-names =
+	/*A0-A7*/ "","","","","","","","",
+	/*B0-B7*/ "power-bmc-nic","presence-ocp-debug",
+		  "power-bmc-slot1","power-bmc-slot2",
+		  "power-bmc-slot3","power-bmc-slot4","","",
+	/*C0-C7*/ "presence-ocp-nic","","","reset-cause-nic-primary",
+		  "reset-cause-nic-secondary","","","",
+	/*D0-D7*/ "","","","","","","","",
+	/*E0-E7*/ "","","","","","","","",
+	/*F0-F7*/ "slot1-bmc-reset-button","slot2-bmc-reset-button",
+		  "slot3-bmc-reset-button","slot4-bmc-reset-button",
+		  "","","","presence-emmc",
+	/*G0-G7*/ "","","","","","","","",
+	/*H0-H7*/ "","","","",
+		  "presence-mb-slot1","presence-mb-slot2",
+		  "presence-mb-slot3","presence-mb-slot4",
+	/*I0-I7*/ "","","","","","","bb-bmc-button","",
+	/*J0-J7*/ "","","","","","","","",
+	/*K0-K7*/ "","","","","","","","",
+	/*L0-L7*/ "","","","","","","","",
+	/*M0-M7*/ "","power-nic-bmc-enable","","usb-bmc-enable","","reset-cause-usb-hub","","",
+	/*N0-N7*/ "","","","","bmc-ready","","","",
+	/*O0-O7*/ "","","","","","","fan0-bmc-cpld-enable","fan1-bmc-cpld-enable",
+	/*P0-P7*/ "fan2-bmc-cpld-enable","fan3-bmc-cpld-enable",
+		  "reset-cause-pcie-slot1","reset-cause-pcie-slot2",
+		  "reset-cause-pcie-slot3","reset-cause-pcie-slot4","","",
+	/*Q0-Q7*/ "","","","","","","","",
+	/*R0-R7*/ "","","","","","","","",
+	/*S0-S7*/ "","","power-p5v-usb","presence-bmc-tpm","","","","",
+	/*T0-T7*/ "","","","","","","","",
+	/*U0-U7*/ "","","","","","","","GND",
+	/*V0-V7*/ "bmc-slot1-ac-button","bmc-slot2-ac-button",
+		  "bmc-slot3-ac-button","bmc-slot4-ac-button",
+		  "","","","",
+	/*W0-W7*/ "","","","","","","","",
+	/*X0-X7*/ "","","","","","","","",
+	/*Y0-Y7*/ "","","","reset-cause-emmc","","","","",
+	/*Z0-Z7*/ "","","","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/ "","","","","","","","",
+	/*18B0-18B7*/ "","","","","","","","",
+	/*18C0-18C7*/ "","","","","","","","",
+	/*18D0-18D7*/ "","","","","","","","",
+	/*18E0-18E3*/ "","","","","","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva-cmc.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva-cmc.dts
new file mode 100644
index 000000000000..f04ef9063520
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva-cmc.dts
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2023 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Minerva CMC";
+	compatible = "facebook,minerva-cmc", "aspeed,ast2600";
+
+	aliases {
+		serial5 = &uart5;
+	};
+
+	chosen {
+		stdout-path = "serial5:57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 2>;
+	};
+};
+
+&uart6 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	use-ncsi;
+	mlx,multi-host;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sgpiom1 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4B>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	multi-master;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&adc0 {
+	aspeed,int-vref-microvolt = <2500000>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	aspeed,int-vref-microvolt = <2500000>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minipack.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minipack.dts
new file mode 100644
index 000000000000..aafd1042b6e5
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minipack.dts
@@ -0,0 +1,1339 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Facebook Inc.
+/dts-v1/;
+
+#include "ast2500-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Minipack 100 BMC";
+	compatible = "facebook,minipack-bmc", "aspeed,ast2500";
+
+	aliases {
+		/*
+		 * Override the default serial aliases to avoid breaking
+		 * the legacy applications.
+		 */
+		serial0 = &uart5;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+
+		/*
+		 * i2c switch 2-0070, pca9548, 8 child channels assigned
+		 * with bus number 16-23.
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * i2c switch 8-0070, pca9548, 8 child channels assigned
+		 * with bus number 24-31.
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		/*
+		 * i2c switch 9-0070, pca9548, 8 child channels assigned
+		 * with bus number 32-39.
+		 */
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
+		i2c38 = &imux38;
+		i2c39 = &imux39;
+
+		/*
+		 * i2c switch 11-0070, pca9548, 8 child channels assigned
+		 * with bus number 40-47.
+		 */
+		i2c40 = &imux40;
+		i2c41 = &imux41;
+		i2c42 = &imux42;
+		i2c43 = &imux43;
+		i2c44 = &imux44;
+		i2c45 = &imux45;
+		i2c46 = &imux46;
+		i2c47 = &imux47;
+
+		/*
+		 * I2C Switch 24-0071 (channel #0 of 8-0070): 8 channels for
+		 * connecting to left PDB (Power Distribution Board).
+		 */
+		i2c48 = &imux48;
+		i2c49 = &imux49;
+		i2c50 = &imux50;
+		i2c51 = &imux51;
+		i2c52 = &imux52;
+		i2c53 = &imux53;
+		i2c54 = &imux54;
+		i2c55 = &imux55;
+
+		/*
+		 * I2C Switch 25-0072 (channel #1 of 8-0070): 8 channels for
+		 * connecting to right PDB (Power Distribution Board).
+		 */
+		i2c56 = &imux56;
+		i2c57 = &imux57;
+		i2c58 = &imux58;
+		i2c59 = &imux59;
+		i2c60 = &imux60;
+		i2c61 = &imux61;
+		i2c62 = &imux62;
+		i2c63 = &imux63;
+
+		/*
+		 * I2C Switch 26-0076 (channel #2 of 8-0070): 8 channels for
+		 * connecting to top FCM (Fan Control Module).
+		 */
+		i2c64 = &imux64;
+		i2c65 = &imux65;
+		i2c66 = &imux66;
+		i2c67 = &imux67;
+		i2c68 = &imux68;
+		i2c69 = &imux69;
+		i2c70 = &imux70;
+		i2c71 = &imux71;
+
+		/*
+		 * I2C Switch 27-0076 (channel #3 of 8-0070): 8 channels for
+		 * connecting to bottom FCM (Fan Control Module).
+		 */
+		i2c72 = &imux72;
+		i2c73 = &imux73;
+		i2c74 = &imux74;
+		i2c75 = &imux75;
+		i2c76 = &imux76;
+		i2c77 = &imux77;
+		i2c78 = &imux78;
+		i2c79 = &imux79;
+
+		/*
+		 * I2C Switch 40-0073 (channel #0 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #1 (1-based).
+		 */
+		i2c80 = &imux80;
+		i2c81 = &imux81;
+		i2c82 = &imux82;
+		i2c83 = &imux83;
+		i2c84 = &imux84;
+		i2c85 = &imux85;
+		i2c86 = &imux86;
+		i2c87 = &imux87;
+
+		/*
+		 * I2C Switch 41-0073 (channel #1 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #2 (1-based).
+		 */
+		i2c88 = &imux88;
+		i2c89 = &imux89;
+		i2c90 = &imux90;
+		i2c91 = &imux91;
+		i2c92 = &imux92;
+		i2c93 = &imux93;
+		i2c94 = &imux94;
+		i2c95 = &imux95;
+
+		/*
+		 * I2C Switch 42-0073 (channel #2 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #3 (1-based).
+		 */
+		i2c96 = &imux96;
+		i2c97 = &imux97;
+		i2c98 = &imux98;
+		i2c99 = &imux99;
+		i2c100 = &imux100;
+		i2c101 = &imux101;
+		i2c102 = &imux102;
+		i2c103 = &imux103;
+
+		/*
+		 * I2C Switch 43-0073 (channel #3 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #4 (1-based).
+		 */
+		i2c104 = &imux104;
+		i2c105 = &imux105;
+		i2c106 = &imux106;
+		i2c107 = &imux107;
+		i2c108 = &imux108;
+		i2c109 = &imux109;
+		i2c110 = &imux110;
+		i2c111 = &imux111;
+
+		/*
+		 * I2C Switch 44-0073 (channel #4 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #5 (1-based).
+		 */
+		i2c112 = &imux112;
+		i2c113 = &imux113;
+		i2c114 = &imux114;
+		i2c115 = &imux115;
+		i2c116 = &imux116;
+		i2c117 = &imux117;
+		i2c118 = &imux118;
+		i2c119 = &imux119;
+
+		/*
+		 * I2C Switch 45-0073 (channel #5 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #6 (1-based).
+		 */
+		i2c120 = &imux120;
+		i2c121 = &imux121;
+		i2c122 = &imux122;
+		i2c123 = &imux123;
+		i2c124 = &imux124;
+		i2c125 = &imux125;
+		i2c126 = &imux126;
+		i2c127 = &imux127;
+
+		/*
+		 * I2C Switch 46-0073 (channel #6 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #7 (1-based).
+		 */
+		i2c128 = &imux128;
+		i2c129 = &imux129;
+		i2c130 = &imux130;
+		i2c131 = &imux131;
+		i2c132 = &imux132;
+		i2c133 = &imux133;
+		i2c134 = &imux134;
+		i2c135 = &imux135;
+
+		/*
+		 * I2C Switch 47-0073 (channel #7 of 11-0070): connecting
+		 * to PIM (Port Interface Module) #8 (1-based).
+		 */
+		i2c136 = &imux136;
+		i2c137 = &imux137;
+		i2c138 = &imux138;
+		i2c139 = &imux139;
+		i2c140 = &imux140;
+		i2c141 = &imux141;
+		i2c142 = &imux142;
+		i2c143 = &imux143;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+		bootargs = "debug console=ttyS1,9600n8 root=/dev/ram rw";
+	};
+};
+
+&wdt2 {
+	status = "okay";
+	aspeed,reset-type = "system";
+};
+
+/*
+ * Both firmware flashes are 64MB on Minipack BMC.
+ */
+&fmc_flash0 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/*
+		 * u-boot partition: 384KB.
+		 */
+		u-boot@0 {
+			reg = <0x0 0x60000>;
+			label = "u-boot";
+		};
+
+		/*
+		 * u-boot environment variables: 128KB.
+		 */
+		u-boot-env@60000 {
+			reg = <0x60000 0x20000>;
+			label = "env";
+		};
+
+		/*
+		 * FIT image: 55.5 MB.
+		 */
+		fit@80000 {
+			reg = <0x80000 0x3780000>;
+			label = "fit";
+		};
+
+		/*
+		 * "data0" partition (8MB) is reserved for persistent
+		 * data store.
+		 */
+		data0@3800000 {
+			reg = <0x3800000 0x800000>;
+			label = "data0";
+		};
+
+		/*
+		 * "flash0" partition (covering the entire flash) is
+		 * explicitly created to avoid breaking legacy applications.
+		 */
+		flash0@0 {
+			reg = <0x0 0x4000000>;
+			label = "flash0";
+		};
+	};
+};
+
+&fmc_flash1 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		flash1@0 {
+			reg = <0x0 0x4000000>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-0 = <&pinctrl_txd1_default
+		     &pinctrl_rxd1_default
+		     &pinctrl_ncts1_default
+		     &pinctrl_ndsr1_default
+		     &pinctrl_ndtr1_default
+		     &pinctrl_nrts1_default>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+		     &pinctrl_rxd2_default>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd4_default
+		     &pinctrl_rxd4_default>;
+};
+
+&i2c0 {
+	status = "okay";
+	bus-frequency = <400000>;
+	multi-master;
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/*
+	 * I2C Switch 2-0070 is connecting to SCM (System Controller
+	 * Module).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+	multi-master;
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		/*
+		 * I2C Switch 8-0070 channel #0: connecting to left PDB
+		 * (Power Distribution Board).
+		 */
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				imux48: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux49: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux50: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux51: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux52: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux53: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux54: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux55: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 8-0070 channel #1: connecting to right PDB
+		 * (Power Distribution Board).
+		 */
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@72 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72>;
+				i2c-mux-idle-disconnect;
+
+				imux56: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux57: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux58: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux59: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux60: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux61: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux62: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux63: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 8-0070 channel #2: connecting to top FCM
+		 * (Fan Control Module).
+		 */
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux64: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux65: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux66: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux67: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux68: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux69: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux70: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux71: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 8-0070 channel #3: connecting to bottom
+		 * FCM (Fan Control Module).
+		 */
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			i2c-mux@76 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x76>;
+				i2c-mux-idle-disconnect;
+
+				imux72: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux73: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux74: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux75: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux76: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux77: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux78: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux79: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	/*
+	 * I2C Switch 9-0070 is connecting to MAC/PHY EEPROMs on SMB
+	 * (Switch Main Board).
+	 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux36: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux37: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux38: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux39: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		/*
+		 * I2C Switch 11-0070 channel #0: connecting to PIM
+		 * (Port Interface Module) #1 (1-based).
+		 */
+		imux40: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux80: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux81: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux82: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux83: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux84: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux85: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux86: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux87: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #1: connecting to PIM
+		 * (Port Interface Module) #2 (1-based).
+		 */
+		imux41: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux88: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux89: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux90: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux91: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux92: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux93: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux94: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux95: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #2: connecting to PIM
+		 * (Port Interface Module) #3 (1-based).
+		 */
+		imux42: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux96: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux97: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux98: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux99: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux100: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux101: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux102: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux103: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #3: connecting to PIM
+		 * (Port Interface Module) #4 (1-based).
+		 */
+		imux43: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux104: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux105: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux106: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux107: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux108: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux109: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux110: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux111: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #4: connecting to PIM
+		 * (Port Interface Module) #5 (1-based).
+		 */
+		imux44: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux112: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux113: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux114: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux115: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux116: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux117: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux118: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux119: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #5: connecting to PIM
+		 * (Port Interface Module) #6 (1-based).
+		 */
+		imux45: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux120: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux121: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux122: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux123: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux124: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux125: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux126: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux127: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #6: connecting to PIM
+		 * (Port Interface Module) #7 (1-based).
+		 */
+		imux46: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux128: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux129: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux130: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux131: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux132: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux133: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux134: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux135: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		/*
+		 * I2C Switch 11-0070 channel #7: connecting to PIM
+		 * (Port Interface Module) #8 (1-based).
+		 */
+		imux47: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			i2c-mux@73 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x73>;
+				i2c-mux-idle-disconnect;
+
+				imux136: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				imux137: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				imux138: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				imux139: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				imux140: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				imux141: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				imux142: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				imux143: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-tiogapass.dts
index 5d7cbd9164d4..704ee684e0fb 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-tiogapass.dts
@@ -5,6 +5,7 @@
 
 #include "aspeed-g5.dtsi"
 #include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
 
 / {
 	model = "Facebook TiogaPass BMC";
@@ -36,7 +37,7 @@
 	};
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -81,11 +82,6 @@
 	status = "okay";
 };
 
-&vuart {
-	// VUART Host Console
-	status = "okay";
-};
-
 &uart1 {
 	// Host Console
 	status = "okay";
@@ -112,13 +108,76 @@
 &kcs2 {
 	// BMC KCS channel 2
 	status = "okay";
-	kcs_addr = <0xca8>;
+	aspeed,lpc-io-reg = <0xca8>;
 };
 
 &kcs3 {
 	// BMC KCS channel 3
 	status = "okay";
-	kcs_addr = <0xca2>;
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"BMC_CPLD_FPGA_SEL","","","","","","","",
+	/*B0-B7*/	"","BMC_DEBUG_EN","","","","BMC_PPIN","PS_PWROK",
+			"IRQ_PVDDQ_GHJ_VRHOT_LVT3",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"BIOS_MRC_DEBUG_MSG_DIS","BOARD_REV_ID0","",
+			"BOARD_REV_ID1","IRQ_DIMM_SAVE_LVT3","BOARD_REV_ID2",
+			"CPU_ERR0_LVT3_BMC","CPU_ERR1_LVT3_BMC",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON",
+			"POWER_OUT","NMI_BUTTON","","CPU0_PROCHOT_LVT3_ BMC",
+			"CPU1_PROCHOT_LVT3_ BMC",
+	/*F0-F7*/	"IRQ_PVDDQ_ABC_VRHOT_LVT3","",
+			"IRQ_PVCCIN_CPU0_VRHOT_LVC3",
+			"IRQ_PVCCIN_CPU1_VRHOT_LVC3",
+			"IRQ_PVDDQ_KLM_VRHOT_LVT3","","P3VBAT_BRIDGE_EN","",
+	/*G0-G7*/	"CPU_ERR2_LVT3","CPU_CATERR_LVT3","PCH_BMC_THERMTRIP",
+			"CPU0_SKTOCC_LVT3","","","","BIOS_SMI_ACTIVE",
+	/*H0-H7*/	"LED_POST_CODE_0","LED_POST_CODE_1","LED_POST_CODE_2",
+			"LED_POST_CODE_3","LED_POST_CODE_4","LED_POST_CODE_5",
+			"LED_POST_CODE_6","LED_POST_CODE_7",
+	/*I0-I7*/	"CPU0_FIVR_FAULT_LVT3","CPU1_FIVR_FAULT_LVT3",
+			"FORCE_ADR","UV_ADR_TRIGGER_EN","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"IRQ_UV_DETECT","IRQ_OC_DETECT","HSC_TIMER_EXP","",
+			"MEM_THERM_EVENT_PCH","PMBUS_ALERT_BUF_EN","","",
+	/*M0-M7*/	"CPU0_RC_ERROR","CPU1_RC_ERROR","","OC_DETECT_EN",
+			"CPU0_THERMTRIP_LATCH_LVT3",
+			"CPU1_THERMTRIP_LATCH_LVT3","","",
+	/*N0-N7*/	"","","","CPU_MSMI_LVT3","","BIOS_SPI_BMC_CTRL","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"BOARD_SKU_ID0","BOARD_SKU_ID1","BOARD_SKU_ID2",
+			"BOARD_SKU_ID3","BOARD_SKU_ID4","BMC_PREQ",
+			"BMC_PWR_DEBUG","RST_RSMRST",
+	/*Q0-Q7*/	"","","","","UARTSW_LSB","UARTSW_MSB",
+			"POST_CARD_PRES_BMC","PE_BMC_WAKE",
+	/*R0-R7*/	"","","BMC_TCK_MUX_SEL","BMC_PRDY",
+			"BMC_XDP_PRSNT_IN","RST_BMC_PLTRST_BUF","SLT_CFG0",
+			"SLT_CFG1",
+	/*S0-S7*/	"THROTTLE","BMC_READY","","HSC_SMBUS_SWITCH_EN","",
+			"","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","BMC_FAULT","","",
+	/*V0-V7*/	"","","","FAST_PROCHOT_EN","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","GLOBAL_RST_WARN",
+			"CPU0_MEMABC_MEMHOT_LVT3_BMC",
+			"CPU0_MEMDEF_MEMHOT_LVT3_BMC",
+			"CPU1_MEMGHJ_MEMHOT_LVT3_BMC",
+			"CPU1_MEMKLM_MEMHOT_LVT3_BMC",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","BMC_JTAG_SEL","SIO_ONCONTROL","",
+			"","","",
+	/*Z0-Z7*/	"","SIO_POWER_GOOD","IRQ_PVDDQ_DEF_VRHOT_LVT3","",
+			"","","","",
+	/*AA0-AA7*/	"CPU1_SKTOCC_LVT3","IRQ_SML1_PMBUS_ALERT",
+			"SERVER_POWER_LED","","PECI_MUX_SELECT","UV_HIGH_SET",
+			"","POST_COMPLETE",
+	/*AB0-AB7*/	"IRQ_HSC_FAULT","OCP_MEZZA_PRES","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
 };
 
 &mac0 {
@@ -132,6 +191,14 @@
 	use-ncsi;
 };
 
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii2_default>;
+	use-ncsi;
+};
+
 &adc {
 	status = "okay";
 };
@@ -144,7 +211,7 @@
 &i2c1 {
 	status = "okay";
 	//X24 Riser
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9544";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -176,7 +243,7 @@
 				pagesize = <32>;
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9546";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -236,7 +303,7 @@
 				pagesize = <32>;
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9546";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -296,7 +363,7 @@
 				pagesize = <32>;
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9546";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -368,6 +435,11 @@
 &i2c4 {
 	status = "okay";
 	// BMC Debug Header
+	ipmb0@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
 };
 
 &i2c5 {
@@ -435,6 +507,11 @@
 &i2c7 {
 	status = "okay";
 	//HSC, AirMax Conn A
+	adm1278@45 {
+		compatible = "adm1275";
+		reg = <0x45>;
+		shunt-resistor-micro-ohms = <250>;
+	};
 };
 
 &i2c8 {
@@ -449,6 +526,11 @@
 &i2c9 {
 	status = "okay";
 	//USB Debug Connector
+	ipmb0@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
 };
 
 &pwm_tacho {
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge100.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge100.dts
new file mode 100644
index 000000000000..97cd11c3d9a5
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge100.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Facebook Inc.
+/dts-v1/;
+
+#include "ast2400-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Wedge 100 BMC";
+	compatible = "facebook,wedge100-bmc", "aspeed,ast2400";
+
+	chosen {
+		stdout-path = &uart3;
+		bootargs = "console=ttyS2,9600n8 root=/dev/ram rw";
+	};
+
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>;
+	};
+};
+
+&wdt2 {
+	status = "okay";
+	aspeed,reset-type = "system";
+};
+
+&fmc {
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "spi0.1";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash1@0 {
+				reg = <0x0 0x2000000>;
+				label = "flash1";
+			};
+		};
+	};
+};
+
+&i2c7 {
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge40.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge40.dts
new file mode 100644
index 000000000000..6624855d8ebd
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge40.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Facebook Inc.
+/dts-v1/;
+
+#include "ast2400-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Wedge 40 BMC";
+	compatible = "facebook,wedge40-bmc", "aspeed,ast2400";
+
+	chosen {
+		stdout-path = &uart3;
+		bootargs = "console=ttyS2,9600n8 root=/dev/ram rw";
+	};
+
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>;
+	};
+};
+
+&wdt2 {
+	status = "disabled";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+		     &pinctrl_pwm1_default
+		     &pinctrl_pwm6_default
+		     &pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x01>;
+	};
+
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x03>;
+	};
+
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x05>;
+	};
+
+	fan@7 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x07>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-minipack.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts
index 88ce4ff9f47e..a677c827e758 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-minipack.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts
@@ -1,27 +1,18 @@
 // SPDX-License-Identifier: GPL-2.0+
-// Copyright (c) 2018 Facebook Inc.
+// Copyright (c) 2019 Facebook Inc.
 /dts-v1/;
 
+#include <dt-bindings/gpio/aspeed-gpio.h>
 #include "ast2500-facebook-netbmc-common.dtsi"
 
 / {
-	model = "Facebook Minipack 100 BMC";
-	compatible = "facebook,minipack-bmc", "aspeed,ast2500";
+	model = "Facebook Wedge 400 BMC";
+	compatible = "facebook,wedge400-bmc", "aspeed,ast2500";
 
 	aliases {
 		/*
-		 * Override the default serial aliases to avoid breaking
-		 * the legacy applications.
-		 */
-		serial0 = &uart5;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
-
-		/*
-		 * i2c switch 2-0070, pca9548, 8 child channels assigned
-		 * with bus number 16-23.
+		 * PCA9548 (2-0070) provides 8 channels connecting to
+		 * SCM (System Controller Module).
 		 */
 		i2c16 = &imux16;
 		i2c17 = &imux17;
@@ -33,8 +24,8 @@
 		i2c23 = &imux23;
 
 		/*
-		 * i2c switch 8-0070, pca9548, 8 child channels assigned
-		 * with bus number 24-31.
+		 * PCA9548 (8-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
 		 */
 		i2c24 = &imux24;
 		i2c25 = &imux25;
@@ -46,8 +37,8 @@
 		i2c31 = &imux31;
 
 		/*
-		 * i2c switch 9-0070, pca9548, 8 child channels assigned
-		 * with bus number 32-39.
+		 * PCA9548 (11-0076) provides 8 channels connecting to
+		 * FCM (Fan Controller Module).
 		 */
 		i2c32 = &imux32;
 		i2c33 = &imux33;
@@ -58,62 +49,65 @@
 		i2c38 = &imux38;
 		i2c39 = &imux39;
 
-		/*
-		 * i2c switch 11-0070, pca9548, 8 child channels assigned
-		 * with bus number 40-47.
-		 */
-		i2c40 = &imux40;
-		i2c41 = &imux41;
-		i2c42 = &imux42;
-		i2c43 = &imux43;
-		i2c44 = &imux44;
-		i2c45 = &imux45;
-		i2c46 = &imux46;
-		i2c47 = &imux47;
+		spi2 = &spi_gpio;
 	};
 
 	chosen {
 		stdout-path = &uart1;
-		bootargs = "debug console=ttyS1,9600n8 root=/dev/ram rw";
+		bootargs = "console=ttyS0,9600n8 root=/dev/ram rw";
 	};
-};
 
-&wdt2 {
-	status = "okay";
-	aspeed,reset-type = "system";
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			      <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>;
+	};
+
+	/*
+	 * GPIO-based SPI Master is required to access SPI TPM, because
+	 * full-duplex SPI transactions are not supported by ASPEED SPI
+	 * Controllers.
+	 */
+	spi_gpio: spi {
+		status = "okay";
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cs-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+		gpio-sck = <&gpio ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+
+		tpmdev@0 {
+			compatible = "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
 };
 
 /*
- * Both firmware flashes are 64MB on Minipack BMC.
+ * Both firmware flashes are 128MB on Wedge400 BMC.
  */
 &fmc_flash0 {
-	partitions {
-		data0@1c00000 {
-			reg = <0x1c00000 0x2400000>;
-		};
-		flash0@0 {
-			reg = <0x0 0x4000000>;
-		};
-	};
+#include "facebook-bmc-flash-layout-128.dtsi"
 };
 
 &fmc_flash1 {
 	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
 		flash1@0 {
-			reg = <0x0 0x4000000>;
+			reg = <0x0 0x8000000>;
+			label = "flash1";
 		};
 	};
 };
 
-&uart1 {
-	pinctrl-0 = <&pinctrl_txd1_default
-		     &pinctrl_rxd1_default
-		     &pinctrl_ncts1_default
-		     &pinctrl_ndsr1_default
-		     &pinctrl_ndtr1_default
-		     &pinctrl_nrts1_default>;
-};
-
 &uart2 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -128,10 +122,14 @@
 		     &pinctrl_rxd4_default>;
 };
 
+/*
+ * I2C bus #0 is multi-master environment dedicated for BMC and Bridge IC
+ * communication.
+ */
 &i2c0 {
 	status = "okay";
-	bus-frequency = <400000>;
 	multi-master;
+	bus-frequency = <1000000>;
 };
 
 &i2c1 {
@@ -141,11 +139,12 @@
 &i2c2 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x70>;
+		i2c-mux-idle-disconnect;
 
 		imux16: i2c@0 {
 			#address-cells = <1>;
@@ -203,7 +202,6 @@
 
 &i2c4 {
 	status = "okay";
-	multi-master;
 };
 
 &i2c5 {
@@ -221,11 +219,12 @@
 &i2c8 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x70>;
+		i2c-mux-idle-disconnect;
 
 		imux24: i2c@0 {
 			#address-cells = <1>;
@@ -274,17 +273,27 @@
 			#size-cells = <0>;
 			reg = <7>;
 		};
+
 	};
 };
 
 &i2c9 {
 	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@76 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		reg = <0x70>;
+		reg = <0x76>;
+		i2c-mux-idle-disconnect;
 
 		imux32: i2c@0 {
 			#address-cells = <1>;
@@ -333,76 +342,35 @@
 			#size-cells = <0>;
 			reg = <7>;
 		};
+
 	};
 };
 
-&i2c10 {
+&i2c12 {
 	status = "okay";
 };
 
-&i2c11 {
+&i2c13 {
 	status = "okay";
+};
 
-	i2c-switch@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		imux40: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux41: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux42: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux43: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux44: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux45: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux46: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux47: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
+&adc {
+	status = "okay";
 };
 
-&i2c12 {
+&ehci1 {
 	status = "okay";
 };
 
-&i2c13 {
+&uhci {
 	status = "okay";
 };
+
+&sdhci1 {
+	max-frequency = <25000000>;
+	/*
+	 * DMA mode needs to be disabled to avoid conflicts with UHCI
+	 * Controller in AST2500 SoC.
+	 */
+	sdhci-caps-mask = <0x0 0x580000>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-yamp.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yamp.dts
index 52933598aac6..98fe0d6c8188 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-yamp.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yamp.dts
@@ -35,7 +35,6 @@
 &mac0 {
 	status = "okay";
 	use-ncsi;
-	no-hw-checksum;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rmii1_default>;
 	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
@@ -58,7 +57,7 @@
 &i2c2 {
 	status = "okay";
 
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -109,3 +108,20 @@
 &i2c13 {
 	status = "okay";
 };
+
+&fmc_flash0 {
+#include "facebook-bmc-flash-layout.dtsi"
+};
+
+&fmc_flash1 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		flash1@0 {
+			reg = <0x0 0x2000000>;
+			label = "flash1";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
new file mode 100644
index 000000000000..64075cc41d92
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -0,0 +1,624 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 Facebook Inc.
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Yosemite 4 BMC";
+	compatible = "facebook,yosemite4-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		serial5 = &uart6;
+		serial6 = &uart7;
+		serial7 = &uart8;
+		serial8 = &uart9;
+	};
+
+	chosen {
+		stdout-path = "serial4:57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+				<&adc1 0>, <&adc1 1>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart6 {
+	status = "okay";
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	use-ncsi;
+	mlx,multi-host;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	use-ncsi;
+	mlx,multi-host;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc2";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	bus-frequency = <400000>;
+	i2c-mux@70 {
+		compatible = "nxp,pca9544";
+		idle-state = <0>;
+		i2c-mux-idle-disconnect;
+		reg = <0x70>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+	bus-frequency = <400000>;
+	i2c-mux@71 {
+		compatible = "nxp,pca9544";
+		idle-state = <0>;
+		i2c-mux-idle-disconnect;
+		reg = <0x71>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+	bus-frequency = <400000>;
+};
+
+&i2c11 {
+	status = "okay";
+	power-sensor@10 {
+		compatible = "adi, adm1272";
+		reg = <0x10>;
+	};
+
+	power-sensor@12 {
+		compatible = "adi, adm1272";
+		reg = <0x12>;
+	};
+
+	gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp75";
+		reg = <0x49>;
+	};
+
+	temperature-sensor@4a {
+		compatible = "ti,tmp75";
+		reg = <0x4a>;
+	};
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c256";
+		reg = <0x54>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	bus-frequency = <400000>;
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	rtc@6f {
+		compatible = "nuvoton,nct3018y";
+		reg = <0x6f>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+	bus-frequency = <400000>;
+};
+
+&i2c14 {
+	status = "okay";
+	bus-frequency = <400000>;
+	adc@1d {
+		compatible = "ti,adc128d818";
+		reg = <0x1d>;
+		ti,mode = /bits/ 8 <2>;
+	};
+
+	adc@35 {
+		compatible = "ti,adc128d818";
+		reg = <0x35>;
+		ti,mode = /bits/ 8 <2>;
+	};
+
+	adc@37 {
+		compatible = "ti,adc128d818";
+		reg = <0x37>;
+		ti,mode = /bits/ 8 <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "ti,ina230";
+		reg = <0x40>;
+	};
+
+	power-sensor@41 {
+		compatible = "ti,ina230";
+		reg = <0x41>;
+	};
+
+	power-sensor@42 {
+		compatible = "ti,ina230";
+		reg = <0x42>;
+	};
+
+	power-sensor@43 {
+		compatible = "ti,ina230";
+		reg = <0x43>;
+	};
+
+	power-sensor@44 {
+		compatible = "ti,ina230";
+		reg = <0x44>;
+	};
+
+	temperature-sensor@4e {
+		compatible = "ti,tmp75";
+		reg = <0x4e>;
+	};
+
+	temperature-sensor@4f {
+		compatible = "ti,tmp75";
+		reg = <0x4f>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9846";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		idle-state = <0>;
+		i2c-mux-idle-disconnect;
+		reg = <0x71>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <2>;
+			};
+
+			pwm@20{
+				compatible = "max31790";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			gpio@22{
+				compatible = "ti,tca6424";
+				reg = <0x22>;
+			};
+
+			pwm@23{
+				compatible = "max31790";
+				reg = <0x23>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			adc@33 {
+				compatible = "maxim,max11615";
+				reg = <0x33>;
+			};
+
+			eeprom@52 {
+				compatible = "atmel,24c128";
+				reg = <0x52>;
+			};
+
+			gpio@61 {
+				compatible = "nxp,pca9552";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <2>;
+			};
+
+			pwm@20{
+				compatible = "max31790";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			gpio@22{
+				compatible = "ti,tca6424";
+				reg = <0x22>;
+			};
+
+			pwm@23{
+				compatible = "max31790";
+				reg = <0x23>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			adc@33 {
+				compatible = "maxim,max11615";
+				reg = <0x33>;
+			};
+
+			eeprom@52 {
+				compatible = "atmel,24c128";
+				reg = <0x52>;
+			};
+
+			gpio@61 {
+				compatible = "nxp,pca9552";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		idle-state = <0>;
+		i2c-mux-idle-disconnect;
+		reg = <0x73>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adc@35 {
+				compatible = "maxim,max11617";
+				reg = <0x35>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adc@35 {
+				compatible = "maxim,max11617";
+				reg = <0x35>;
+			};
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+	mctp-controller;
+	multi-master;
+	bus-frequency = <400000>;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9544";
+		idle-state = <0>;
+		i2c-mux-idle-disconnect;
+		reg = <0x72>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+			&pinctrl_adc2_default &pinctrl_adc3_default
+			&pinctrl_adc4_default &pinctrl_adc5_default
+			&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>;
+};
+
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemitev2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemitev2.dts
new file mode 100644
index 000000000000..6bf2ff85a40e
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemitev2.dts
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2018 Facebook Inc.
+/dts-v1/;
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Yosemitev2 BMC";
+	compatible = "facebook,yosemitev2-bmc", "aspeed,ast2500";
+	aliases {
+		serial4 = &uart5;
+	};
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	iio-hwmon {
+		// VOLATAGE SENSOR
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0> , <&adc 1> , <&adc 2> ,  <&adc 3> ,
+		<&adc 4> , <&adc 5> , <&adc 6> ,  <&adc 7> ,
+		<&adc 8> , <&adc 9> , <&adc 10>, <&adc 11> ,
+		<&adc 12> , <&adc 13> , <&adc 14> , <&adc 15> ;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+	};
+};
+&uart1 {
+	// Host1 Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+		     &pinctrl_rxd1_default>;
+};
+
+&uart2 {
+	// Host2 Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+		     &pinctrl_rxd2_default>;
+
+};
+
+&uart3 {
+	// Host3 Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd3_default
+		     &pinctrl_rxd3_default>;
+};
+
+&uart4 {
+	// Host4 Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd4_default
+		     &pinctrl_rxd4_default>;
+};
+
+&uart5 {
+	// BMC Console
+	status = "okay";
+};
+
+&vuart {
+	// Virtual UART
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	use-ncsi;
+	mlx,multi-host;
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+			&pinctrl_adc1_default
+			&pinctrl_adc2_default
+			&pinctrl_adc3_default
+			&pinctrl_adc4_default
+			&pinctrl_adc5_default
+			&pinctrl_adc6_default
+			&pinctrl_adc7_default
+			&pinctrl_adc8_default
+			&pinctrl_adc9_default
+			&pinctrl_adc10_default
+			&pinctrl_adc11_default
+			&pinctrl_adc12_default
+			&pinctrl_adc13_default
+			&pinctrl_adc14_default
+			&pinctrl_adc15_default>;
+};
+
+&i2c1 {
+	//Host1 IPMB bus
+	status = "okay";
+	multi-master;
+	ipmb1@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	//Host2 IPMB bus
+	status = "okay";
+	multi-master;
+	ipmb3@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c5 {
+	//Host3 IPMB bus
+	status = "okay";
+	multi-master;
+	ipmb5@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c7 {
+	//Host4 IPMB bus
+	status = "okay";
+	multi-master;
+	ipmb7@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	//FRU EEPROM
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+	tmp421@4e {
+	//INLET TEMP
+		compatible = "ti,tmp421";
+		reg = <0x4e>;
+	};
+	//OUTLET TEMP
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+	//HSC
+	adm1278@40 {
+		compatible = "adi,adm1278";
+		reg = <0x40>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+	//MEZZ_TEMP_SENSOR
+	tmp421@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+	// Debug Card
+	multi-master;
+	ipmb13@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	//FSC
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
new file mode 100644
index 000000000000..cad1b9aac97b
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
@@ -0,0 +1,617 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Bonnell";
+	compatible = "ibm,bonnell-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c11mux0chn0;
+		i2c17 = &i2c11mux0chn1;
+		i2c18 = &i2c11mux0chn2;
+		i2c19 = &i2c11mux0chn3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log@b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fan0 {
+			gpios = <&gpio0 ASPEED_GPIO(G, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		fan1 {
+			gpios = <&gpio0 ASPEED_GPIO(G, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <1000>;
+
+		fan0-presence {
+			label = "fan0-presence";
+			gpios = <&gpio0 ASPEED_GPIO(F, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		fan1-presence {
+			label = "fan1-presence";
+			gpios = <&gpio0 ASPEED_GPIO(F, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <7>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		/*A0-A7*/	"","","","","","","","",
+		/*B0-B7*/	"","","","","","","checkstop","",
+		/*C0-C7*/	"","","","","","","","",
+		/*D0-D7*/	"","","","","","","","",
+		/*E0-E7*/	"","","","","","","","",
+		/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","","",
+		/*G0-G7*/	"fan0","fan1","","","","","","",
+		/*H0-H7*/	"","","rear-enc-id0","rear-enc-fault0","","","","",
+		/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+		/*J0-J7*/	"","","","","","","","",
+		/*K0-K7*/	"","","","","","","","",
+		/*L0-L7*/	"","","","","","","","",
+		/*M0-M7*/	"","","","","","","","",
+		/*N0-N7*/	"","","","","","","","",
+		/*O0-O7*/	"","","","usb-power","","","","",
+		/*P0-P7*/	"","","","","","","","",
+		/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+		/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
+		/*S0-S7*/	"presence-ps0","presence-ps1","","","power-ffs-sync-history","","","",
+		/*T0-T7*/	"","","","","","","","",
+		/*U0-U7*/	"","","","","","","","",
+		/*V0-V7*/	"","","","","","","","",
+		/*W0-W7*/	"","","","","","","","",
+		/*X0-X7*/	"","","","","","","","",
+		/*Y0-Y7*/	"","","","","","","","",
+		/*Z0-Z7*/	"","","","","","","","";
+
+	usb_power {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	tca9554@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"",
+			"",
+			"DASD_BP_PRESENT_N";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	ucd90160@64 {
+		compatible = "ti,ucd90160";
+		reg = <0x64>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply@5a {
+		compatible = "acbel,fsg032";
+		reg = <0x5a>;
+	};
+
+	power-supply@5b {
+		compatible = "acbel,fsg032";
+		reg = <0x5b>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	si7021-a20@40 {
+		compatible = "silabs,si7020";
+		reg = <0x40>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	max31785@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan0: fan@0 {
+			compatible = "pmbus-fan";
+			reg = <0>;
+			tach-pulses = <2>;
+		};
+
+		fan1: fan@1 {
+			compatible = "pmbus-fan";
+			reg = <1>;
+			tach-pulses = <2>;
+		};
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "front-sys-id0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "front-check-log0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "front-enc-fault1";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "front-sys-pwron0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	dps: dps310@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"APSS_RESET_N",
+			"",
+			"N_MODE_CPU_N",
+			"",
+			"",
+			"P10_DCM_PRESENT",
+			"";
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	tca9554@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "BOOT_RCVRY_TWI",
+			"BOOT_RCVRY_UART",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"PE_SWITCH_RSTB_N";
+	};
+
+	tmp435@4c {
+		compatible = "ti,tmp435";
+		reg = <0x4c>;
+	};
+
+	pca9849@75 {
+		compatible = "nxp,pca9849";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c11mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c11mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c11mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power10-dual.dtsi"
+
+&cfam0_i2c10 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
+
+&cfam0_i2c11 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
+
+&cfam0_i2c12 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
+
+&cfam0_i2c13 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
new file mode 100644
index 000000000000..214b2e6a4c6d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
@@ -0,0 +1,4016 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2020 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Everest";
+	compatible = "ibm,everest-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c500 = &cfam4_i2c0;
+		i2c501 = &cfam4_i2c1;
+		i2c510 = &cfam4_i2c10;
+		i2c511 = &cfam4_i2c11;
+		i2c512 = &cfam4_i2c12;
+		i2c513 = &cfam4_i2c13;
+		i2c514 = &cfam4_i2c14;
+		i2c515 = &cfam4_i2c15;
+		i2c602 = &cfam5_i2c2;
+		i2c603 = &cfam5_i2c3;
+		i2c610 = &cfam5_i2c10;
+		i2c611 = &cfam5_i2c11;
+		i2c614 = &cfam5_i2c14;
+		i2c615 = &cfam5_i2c15;
+		i2c616 = &cfam5_i2c16;
+		i2c617 = &cfam5_i2c17;
+		i2c700 = &cfam6_i2c0;
+		i2c701 = &cfam6_i2c1;
+		i2c710 = &cfam6_i2c10;
+		i2c711 = &cfam6_i2c11;
+		i2c712 = &cfam6_i2c12;
+		i2c713 = &cfam6_i2c13;
+		i2c714 = &cfam6_i2c14;
+		i2c715 = &cfam6_i2c15;
+		i2c802 = &cfam7_i2c2;
+		i2c803 = &cfam7_i2c3;
+		i2c810 = &cfam7_i2c10;
+		i2c811 = &cfam7_i2c11;
+		i2c814 = &cfam7_i2c14;
+		i2c815 = &cfam7_i2c15;
+		i2c816 = &cfam7_i2c16;
+		i2c817 = &cfam7_i2c17;
+
+		i2c16 = &i2c4mux0chn0;
+		i2c17 = &i2c4mux0chn1;
+		i2c18 = &i2c4mux0chn2;
+		i2c19 = &i2c5mux0chn0;
+		i2c20 = &i2c5mux0chn1;
+		i2c21 = &i2c5mux0chn2;
+		i2c22 = &i2c5mux0chn3;
+		i2c23 = &i2c6mux0chn0;
+		i2c24 = &i2c6mux0chn1;
+		i2c25 = &i2c6mux0chn2;
+		i2c26 = &i2c6mux0chn3;
+		i2c27 = &i2c14mux0chn0;
+		i2c28 = &i2c14mux0chn1;
+		i2c29 = &i2c14mux0chn2;
+		i2c30 = &i2c14mux0chn3;
+		i2c31 = &i2c14mux1chn0;
+		i2c32 = &i2c14mux1chn1;
+		i2c33 = &i2c14mux1chn2;
+		i2c34 = &i2c14mux1chn3;
+		i2c35 = &i2c15mux0chn0;
+		i2c36 = &i2c15mux0chn1;
+		i2c37 = &i2c15mux0chn2;
+		i2c38 = &i2c15mux0chn3;
+		i2c39 = &i2c15mux1chn0;
+		i2c40 = &i2c15mux1chn1;
+		i2c41 = &i2c15mux1chn2;
+		i2c42 = &i2c15mux1chn3;
+		i2c43 = &i2c15mux2chn0;
+		i2c44 = &i2c15mux2chn1;
+		i2c45 = &i2c15mux2chn2;
+		i2c46 = &i2c15mux2chn3;
+		i2c47 = &i2c8mux0chn0;
+		i2c48 = &i2c8mux0chn1;
+
+		serial4 = &uart5;
+
+		sbefifo500 = &sbefifo500;
+		sbefifo501 = &sbefifo501;
+		sbefifo510 = &sbefifo510;
+		sbefifo511 = &sbefifo511;
+		sbefifo512 = &sbefifo512;
+		sbefifo513 = &sbefifo513;
+		sbefifo514 = &sbefifo514;
+		sbefifo515 = &sbefifo515;
+		sbefifo602 = &sbefifo602;
+		sbefifo603 = &sbefifo603;
+		sbefifo610 = &sbefifo610;
+		sbefifo611 = &sbefifo611;
+		sbefifo614 = &sbefifo614;
+		sbefifo615 = &sbefifo615;
+		sbefifo616 = &sbefifo616;
+		sbefifo617 = &sbefifo617;
+		sbefifo700 = &sbefifo700;
+		sbefifo701 = &sbefifo701;
+		sbefifo710 = &sbefifo710;
+		sbefifo711 = &sbefifo711;
+		sbefifo712 = &sbefifo712;
+		sbefifo713 = &sbefifo713;
+		sbefifo714 = &sbefifo714;
+		sbefifo715 = &sbefifo715;
+		sbefifo802 = &sbefifo802;
+		sbefifo803 = &sbefifo803;
+		sbefifo810 = &sbefifo810;
+		sbefifo811 = &sbefifo811;
+		sbefifo814 = &sbefifo814;
+		sbefifo815 = &sbefifo815;
+		sbefifo816 = &sbefifo816;
+		sbefifo817 = &sbefifo817;
+
+		scom500 = &scom500;
+		scom501 = &scom501;
+		scom510 = &scom510;
+		scom511 = &scom511;
+		scom512 = &scom512;
+		scom513 = &scom513;
+		scom514 = &scom514;
+		scom515 = &scom515;
+		scom602 = &scom602;
+		scom603 = &scom603;
+		scom610 = &scom610;
+		scom611 = &scom611;
+		scom614 = &scom614;
+		scom615 = &scom615;
+		scom616 = &scom616;
+		scom617 = &scom617;
+		scom700 = &scom700;
+		scom701 = &scom701;
+		scom710 = &scom710;
+		scom711 = &scom711;
+		scom712 = &scom712;
+		scom713 = &scom713;
+		scom714 = &scom714;
+		scom715 = &scom715;
+		scom802 = &scom802;
+		scom803 = &scom803;
+		scom810 = &scom810;
+		scom811 = &scom811;
+		scom814 = &scom814;
+		scom815 = &scom815;
+		scom816 = &scom816;
+		scom817 = &scom817;
+
+		spi50 = &cfam4_spi0;
+		spi51 = &cfam4_spi1;
+		spi52 = &cfam4_spi2;
+		spi53 = &cfam4_spi3;
+		spi60 = &cfam5_spi0;
+		spi61 = &cfam5_spi1;
+		spi62 = &cfam5_spi2;
+		spi63 = &cfam5_spi3;
+		spi70 = &cfam6_spi0;
+		spi71 = &cfam6_spi1;
+		spi72 = &cfam6_spi2;
+		spi73 = &cfam6_spi3;
+		spi80 = &cfam7_spi0;
+		spi81 = &cfam7_spi1;
+		spi82 = &cfam7_spi2;
+		spi83 = &cfam7_spi3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log@b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>; /* 16M */
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca0 15 GPIO_ACTIVE_LOW>;
+			linux,code = <15>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
+			linux,code = <14>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
+			linux,code = <13>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
+			linux,code = <12>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* RTC battery fault LED at the back */
+		led-rtc-battery {
+			gpios = <&gpio0 ASPEED_GPIO(H, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		/* BMC Card fault LED at the back */
+		led-bmc {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure Identify LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+				 &pinctrl_adc10_default &pinctrl_adc11_default
+				 &pinctrl_adc12_default &pinctrl_adc13_default
+				 &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"USERSPACE_RSTIND_BUFF","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"led-rtc-battery","led-bmc","led-rear-enc-id0","led-rear-enc-fault0","","","","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
+	/*Q0-Q7*/	"","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","I2C_FLASH_MICRO_N","","",
+	/*S0-S7*/	"","","","","power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","BMC_3RESTART_ATTEMPT_P","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/   "","","","","","","","";
+
+	usb_power {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pca1: pca9552@62 {
+		compatible = "nxp,pca9552";
+		reg = <0x62>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-ps0",
+			"presence-ps1",
+			"presence-ps2",
+			"presence-ps3",
+			"presence-pdb",
+			"presence-tpm",
+			"", "",
+			"presence-cp0",
+			"presence-cp1",
+			"presence-cp2",
+			"presence-cp3",
+			"presence-dasd",
+			"presence-lcd-op",
+			"presence-base-op",
+			"";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	power-supply@6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+
+	power-supply@6d {
+		compatible = "ibm,cffps";
+		reg = <0x6d>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	pca2: pca9552@65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card1",
+			"presence-cable-card2",
+			"presence-cable-card3",
+			"presence-cable-card4",
+			"presence-cable-card5",
+			"expander-cable-card1",
+			"expander-cable-card2",
+			"expander-cable-card3",
+			"expander-cable-card4",
+			"expander-cable-card5";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c01: pca9551@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c01-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c01-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca_cable_card_c02: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c02-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c02-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c03: pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c03-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c03-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	pca3: pca9552@66 {
+		compatible = "nxp,pca9552";
+		reg = <0x66>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card6",
+			"presence-cable-card7",
+			"presence-cable-card8",
+			"presence-cable-card9",
+			"presence-cable-card10",
+			"presence-cable-card11",
+			"expander-cable-card6",
+			"expander-cable-card7",
+			"expander-cable-card8",
+			"expander-cable-card9",
+			"expander-cable-card10",
+			"expander-cable-card11";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca_cable_card_c04: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c04-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c04-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c05: pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c05-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c05-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c06: pca9551@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c06-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c06-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			pca_cable_card_c07: pca9551@63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c07-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c07-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+			compatible = "atmel,24c64";
+			reg = <0x50>;
+			};
+
+			pca_cable_card_c08: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c08-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c08-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			pca_cable_card_c09: pca9551@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c09-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c09-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			pca_cable_card_c10: pca9551@63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca_cable_card_c11: pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard-c11-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard-c11-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+
+	pca_pcie_slot: pca9552@65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@1 {
+			label = "pcieslot-c01";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "pcieslot-c02";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "pcieslot-c03";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcieslot-c04";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "pcieslot-c05";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "pcieslot-c06";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "pcieslot-c07";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "pcieslot-c08";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcieslot-c09";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcieslot-c10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "pcieslot-c11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	pic0_dimm: pca9552@31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm8";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm9";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic1_dimm: pca9552@32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm24";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm25";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm26";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm27";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm28";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm29";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm30";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm31";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic2_dimm: pca9552@33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm32";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm33";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm34";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm35";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm36";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm37";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm38";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm39";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm40";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm41";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm42";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm43";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm44";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm45";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm46";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm47";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic3_dimm: pca9552@30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm48";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm49";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm50";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm51";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm52";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm53";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm54";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm55";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm56";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm57";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm58";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm59";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm60";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm61";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm62";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm63";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic0_vrm_misc: pca9552@34 {
+		compatible = "ibm,pca9552";
+		reg = <0x34>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "planar";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "tpm";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "cpu3-c61";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "cpu0-c14";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "opencapi-connector3";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "opencapi-connector4";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "opencapi-connector5";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "vrm4";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "vrm5";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "vrm6";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "vrm7";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "vrm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "vrm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "vrm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "vrm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pic1_vrm_misc: pca9552@35 {
+		compatible = "ibm,pca9552";
+		reg = <0x35>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "dasd-backplane";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "power-distribution";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "cpu1-c19";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "cpu2-c56";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "opencapi-connector0";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "opencapi-connector1";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "opencapi-connector2";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "vrm0";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "vrm1";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "vrm2";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "vrm3";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "vrm8";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "vrm9";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "vrm10";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "vrm11";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	ucd90320@11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c8mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c8mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c14 {
+	multi-master;
+	status = "okay";
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		idle-state = <1>;
+
+		i2c14mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@51 {
+				compatible = "atmel,24c32";
+				reg = <0x51>;
+			};
+		};
+
+		i2c14mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+
+			pca_oppanel: pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "front-sys-id0";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "front-check-log0";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					label = "front-enc-fault1";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					label = "front-sys-pwron0";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c14mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			max31785@52 {
+				compatible = "maxim,max31785a";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x52>;
+
+				fan@0 {
+					compatible = "pmbus-fan";
+					reg = <0>;
+					tach-pulses = <2>;
+				};
+
+				fan@1 {
+					compatible = "pmbus-fan";
+					reg = <1>;
+					tach-pulses = <2>;
+				};
+
+				fan@2 {
+					compatible = "pmbus-fan";
+					reg = <2>;
+					tach-pulses = <2>;
+				};
+
+				fan@3 {
+					compatible = "pmbus-fan";
+					reg = <3>;
+					tach-pulses = <2>;
+				};
+			};
+
+			pca_fan_nvme: pca9552@60 {
+				compatible = "nxp,pca9552";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "nvme0";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "nvme1";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					label = "nvme2";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					label = "nvme3";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@4 {
+					label = "nvme4";
+					reg = <4>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@5 {
+					label = "nvme5";
+					reg = <5>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@6 {
+					label = "nvme6";
+					reg = <6>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@7 {
+					label = "nvme7";
+					reg = <7>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@8 {
+					label = "nvme8";
+					reg = <8>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@9 {
+					label = "nvme9";
+					reg = <9>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@10 {
+					label = "fan0";
+					reg = <10>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@11 {
+					label = "fan1";
+					reg = <11>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@12 {
+					label = "fan2";
+					reg = <12>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@13 {
+					label = "fan3";
+					reg = <13>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+
+			pca0: pca9552@61 {
+				compatible = "nxp,pca9552";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x61>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"","","","",
+					"","","","",
+					"","","","",
+					"presence-fan3",
+					"presence-fan2",
+					"presence-fan1",
+					"presence-fan0";
+			};
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c14mux1chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux1chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux2chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c15mux2chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <210>, <228>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power10-quad.dtsi"
+
+&fsi_hub0 {
+	cfam@4,0 { /* DCM2_C0 */
+		reg = <4 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <4>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom500: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo500: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom501: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo501: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom510: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo510: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom511: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo511: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom512: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo512: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom513: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo513: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom514: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo514: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom515: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo515: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam4_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ4: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub4: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@5,0 { /* DCM2_C1 */
+		reg = <5 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <5>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom602: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo602: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom603: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo603: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom610: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo610: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom611: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo611: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom614: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo614: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom615: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo615: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom616: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo616: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom617: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo617: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam5_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ5: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub5: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@6,0 { /* DCM3_C0 */
+		reg = <6 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <6>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom700: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo700: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom701: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo701: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom710: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo710: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom711: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo711: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom712: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo712: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom713: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo713: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom714: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo714: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom715: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo715: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam6_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ6: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub6: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@7,0 { /* DCM3_C1 */
+		reg = <7 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <7>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom802: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo802: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom803: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo803: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom810: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo810: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom811: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo811: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom814: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo814: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom815: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo815: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom816: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo816: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom817: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo817: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam7_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ7: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub7: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ4 {
+	reg = <5>;
+};
+
+&fsi_occ5 {
+	reg = <6>;
+};
+
+&fsi_occ6 {
+	reg = <7>;
+};
+
+&fsi_occ7 {
+	reg = <8>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-1s4u.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-1s4u.dts
new file mode 100644
index 000000000000..f5f5b18c113a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-1s4u.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2021 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-bmc-ibm-rainier-4u.dts"
+
+/ {
+	model = "Rainier 1S4U";
+};
+
+&max {
+	/delete-node/ fan3;
+	/delete-node/ fan5;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-4u.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-4u.dts
new file mode 100644
index 000000000000..342546a3c0f5
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-4u.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2020 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-bmc-ibm-rainier.dts"
+
+/ {
+	model = "Rainier 4U";
+};
+
+&i2c3 {
+	power-supply@6a {
+		compatible = "ibm,cffps";
+		reg = <0x6a>;
+	};
+
+	power-supply@6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
new file mode 100644
index 000000000000..5cb0094e21e0
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
@@ -0,0 +1,1741 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2019 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Rainier 2U";
+	compatible = "ibm,rainier-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c2mux0;
+		i2c17 = &i2c2mux1;
+		i2c18 = &i2c2mux2;
+		i2c19 = &i2c2mux3;
+		i2c20 = &i2c4mux0chn0;
+		i2c21 = &i2c4mux0chn1;
+		i2c22 = &i2c4mux0chn2;
+		i2c23 = &i2c5mux0chn0;
+		i2c24 = &i2c5mux0chn1;
+		i2c25 = &i2c6mux0chn0;
+		i2c26 = &i2c6mux0chn1;
+		i2c27 = &i2c6mux0chn2;
+		i2c28 = &i2c6mux0chn3;
+		i2c29 = &i2c11mux0chn0;
+		i2c30 = &i2c11mux0chn1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	i2c2mux: i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		i2c-parent = <&i2c2>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
+			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
+		idle-state = <0>;
+
+		i2c2mux0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c2mux1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c2mux2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c2mux3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* BMC Card fault LED at the back */
+		bmc-ingraham0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure ID LED at the back */
+		rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			label = "fan0-presence";
+			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		event-fan1-presence {
+			label = "fan1-presence";
+			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
+			linux,code = <7>;
+		};
+
+		event-fan2-presence {
+			label = "fan2-presence";
+			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
+			linux,code = <8>;
+		};
+
+		event-fan3-presence {
+			label = "fan3-presence";
+			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
+			linux,code = <9>;
+		};
+
+		event-fan4-presence {
+			label = "fan4-presence";
+			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
+			linux,code = <10>;
+		};
+
+		event-fan5-presence {
+			label = "fan5-presence";
+			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
+			linux,code = <11>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","pcieslot-power","","","",
+	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
+	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
+	"power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+
+	i2c3_mux_oe_n {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "I2C3_MUX_OE_N";
+	};
+
+	usb_power {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	tca_pres1: tca9554@20{
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"DASD_BP2_PRESENT_N",
+			"DASD_BP1_PRESENT_N",
+			"DASD_BP0_PRESENT_N";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	pca_pres1: pca9552@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
+			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
+			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
+			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
+			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
+			"", "", "", "", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard0-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard0-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard3-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard3-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard4-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard4-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	tmp275@4b {
+		compatible = "ti,tmp275";
+		reg = <0x4b>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	pca9552@30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "pcieslot0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "pcieslot1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "pcieslot2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "pcieslot3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcieslot4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "cpu1";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "cpu-vrm1";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "lcd-russel";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552@31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm8";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm9";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm10";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm11";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm12";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm13";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm14";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm15";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552@32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "ddimm16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "ddimm17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "ddimm18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "ddimm19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "ddimm20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "ddimm21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "ddimm22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "ddimm23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "ddimm24";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "ddimm25";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "ddimm26";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "ddimm27";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "ddimm28";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "ddimm29";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "ddimm30";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "ddimm31";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca9552@33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "planar";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "cpu0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "dasd-pyramid0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "dasd-pyramid1";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "dasd-pyramid2";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "cpu0-vrm0";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "rtc-battery";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "base-blyth";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcieslot6";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcieslot7";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "pcieslot8";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "pcieslot9";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "pcieslot10";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "pcieslot11";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "tpm-wilson";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	si7021-a20@40 {
+		compatible = "silabs,si7020";
+		reg = <0x40>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	max: max31785@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan0: fan@0 {
+			compatible = "pmbus-fan";
+			reg = <0>;
+			tach-pulses = <2>;
+		};
+
+		fan1: fan@1 {
+			compatible = "pmbus-fan";
+			reg = <1>;
+			tach-pulses = <2>;
+		};
+
+		fan2: fan@2 {
+			compatible = "pmbus-fan";
+			reg = <2>;
+			tach-pulses = <2>;
+		};
+
+		fan3: fan@3 {
+			compatible = "pmbus-fan";
+			reg = <3>;
+			tach-pulses = <2>;
+		};
+
+		fan4: fan@4 {
+			compatible = "pmbus-fan";
+			reg = <4>;
+			tach-pulses = <2>;
+		};
+
+		fan5: fan@5 {
+			compatible = "pmbus-fan";
+			reg = <5>;
+			tach-pulses = <2>;
+		};
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "front-sys-id0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "front-check-log0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "front-enc-fault1";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "front-sys-pwron0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca0: pca9552@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "fan0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "fan1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "fan2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "fan3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "fan4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "fan5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	dps: dps310@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	ucd90320@11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pca_pres3: pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"", "", "", "", "", "", "", "",
+			"", "", "", "", "", "", "power-config-full-load", "";
+	};
+
+	pca_pres2: pca9552@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT6_PRSNT_EN_RSVD", "SLOT7_PRSNT_EN_RSVD",
+			"SLOT8_PRSNT_EN_RSVD", "SLOT9_PRSNT_EN_RSVD",
+			"SLOT10_PRSNT_EN_RSVD", "SLOT11_PRSNT_EN_RSVD",
+			"SLOT6_EXPANDER_PRSNT_N", "SLOT7_EXPANDER_PRSNT_N",
+			"SLOT8_EXPANDER_PRSNT_N", "SLOT9_EXPANDER_PRSNT_N",
+			"SLOT10_EXPANDER_PRSNT_N", "SLOT11_EXPANDER_PRSNT_N",
+			"", "", "", "";
+	};
+
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	tmp423b@4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	tmp423b@4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	tmp275@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c11mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme1";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme2";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme3";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "nvme4";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "nvme5";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "nvme6";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "nvme7";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme8";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme9";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme10";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme11";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "nvme12";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "nvme13";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "nvme14";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "nvme15";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme16";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme17";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme18";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme19";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "nvme20";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "nvme21";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "nvme22";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "nvme23";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power10-quad.dtsi"
diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-fp5280g2.dts
index c17bb7fce7ff..0dea014e4f30 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-fp5280g2.dts
@@ -3,6 +3,7 @@
 #include "aspeed-g5.dtsi"
 #include <dt-bindings/gpio/aspeed-gpio.h>
 #include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "FP5280G2 BMC";
@@ -10,7 +11,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -72,19 +73,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 3)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(F, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 0)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -94,53 +95,51 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
 			linux,code = <1>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
 			linux,code = <2>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <3>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan6-presence {
+		event-fan6-presence {
 			label = "fan6-presence";
 			gpios = <&pca1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan7-presence {
+		event-fan7-presence {
 			label = "fan7-presence";
 			gpios = <&pca1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
@@ -206,6 +205,39 @@
 
 };
 
+&gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","front-psu","checkstop","cfam-reset","","","init-ok",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"ps0-presence","ps1-presence","","","front-memory","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","front-fan","","","",
+	/*I0-I7*/	"front-syshealth","front-syshot","mux-gpios","enable-gpios","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","power","trans-gpios","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","identify",
+	/*AA0-AA7*/	"clock-gpios","","data-gpios","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
 &fmc {
 	status = "okay";
 
@@ -214,7 +246,7 @@
 		label = "bmc";
 		m25p,fast-read;
 		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout.dtsi"
+#include "openbmc-flash-layout-64.dtsi"
 	};
 };
 
@@ -316,7 +348,7 @@
 		label = "outlet";
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -400,7 +432,7 @@
 &i2c7 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -758,12 +790,12 @@
 	status = "okay";
 
 	power-supply@58 {
-		compatible = "pmbus";
+		compatible = "inspur,ipsps1";
 		reg = <0x58>;
 	};
 
 	power-supply@59 {
-		compatible = "pmbus";
+		compatible = "inspur,ipsps1";
 		reg = <0x59>;
 	};
 };
@@ -871,4 +903,10 @@
 
 };
 
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
 #include "ibm-power9-dual.dtsi"
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-nf5280m6.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-nf5280m6.dts
new file mode 100644
index 000000000000..92b9b3987c92
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-nf5280m6.dts
@@ -0,0 +1,691 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021 Inspur Corporation
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "NF5280M6 BMC";
+	compatible = "inspur,nf5280m6-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+	    compatible = "gpio-leds";
+
+		bmc_alive {
+			label = "bmc_alive";
+			gpios = <&gpio ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+			led-pattern = <1000 1000>;
+		};
+
+		front-fan {
+			label = "front-fan";
+			gpios = <&gpio ASPEED_GPIO(F,2) GPIO_ACTIVE_LOW>;
+		};
+
+	    front-psu {
+			label = "front-psu";
+			gpios = <&gpio ASPEED_GPIO(F,3) GPIO_ACTIVE_LOW>;
+		};
+
+	    front-syshot {
+			label = "front-syshot";
+			gpios = <&gpio ASPEED_GPIO(J, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		front-memory {
+			label = "front-memory";
+			gpios = <&gpio ASPEED_GPIO(S, 7) GPIO_ACTIVE_LOW>;
+		};
+
+		identify {
+			label = "identify";
+			gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+		<&syscon ASPEED_CLK_MAC1RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&gpio {
+	status = "okay";
+	/* Enable GPIOE0 and GPIOE2 pass-through by default */
+	pinctrl-names = "pass-through";
+	pinctrl-0 = <&pinctrl_gpie0_default
+			&pinctrl_gpie2_default>;
+	gpio-line-names =
+	/*A0-A7*/	"","MAC2LINK","BMC_RESET_CPLD","","BMC_SCL9","","MAC2MDC_R","",
+	/*B0-B7*/	"BMC_INIT_OK","FM_SKU_ID2","FM_SPD_DDRCPU_LVLSHFT_DIS_R_N",
+				"FM_CPU_MSMI_CATERR_LVT3_BMC_N","","FM_CPU0_PROCHOT_LVT3_N",
+				"FM_CPU_MEM_THERMTRIP_LVT3_N","BIOS_LOAD_DEFAULT_R_N",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","BMC_SD2CMD","BMC_SD2DAT0","BMC_SD2DAT1","BMC_SD2DAT2",
+				"BMC_SD2DAT3","BMC_SD2DET","BMC_SD2WPT",
+	/*E0-E7*/	"FM_BOARD_ID0","FM_BOARD_ID1","FM_BOARD_ID2","FM_BOARD_ID3",
+				"FM_BOARD_ID4","FM_BOARD_ID5","","",
+	/*F0-F7*/	"PSU1_PRESENT_N","PSU2_PRESENT_N","FAN_FAULT_LED_N","PSU_FAULT_LED_N",
+				"BIOS_DEBUG_MODE_N","FP_LCD_RESET","FAN_TYPE_SEL",
+				"RST_GLB_RST_WARN_N",
+	/*G0-G7*/	"IRQ_LPTM21L_ALERT_N","IRQ_PLD_ALERT_N","AC_FAIL_N","FP_LCD_PRESENT_BMC",
+				"BMC_JTAG_TCK_MUX_SEL","BMC_BIOS_RESERVED","SYS_NMI_N","BMC_NMI_N",
+	/*H0-H7*/	"JTAG_BMC_TDI","JTAG_BMC_TDO","JTAG_BMC_TCK","JTAG_BMC_TMS","FM_BOARD_ID6",
+				"FM_SKU_ID0","IRQ_SML1_PMBUS_ALERT_N","IRQ_SML0_ALERT_MUX_N",
+	/*I0-I7*/	"FM_CPU_ERR0_LVT3_BMC_N","FM_CPU_ERR1_LVT3_BMC_N","FM_BMC_PCH_SCI_LPC_N",
+				"FM_SYS_THROTTLE_LVC3","SPI2_PCH_CS0_N","","","",
+	/*J0-J7*/	"FM_CPU0_SKTOCC_LVT3_N","FM_CPU1_SKTOCC_LVT3_N","","SYSHOT_FAULT_LED_N",
+				"VGA_HSYNC","VGA_VSYNC","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","SYS_UART_TXD1","SYS_UART_RXD1",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","FM_PCH_BMC_THERMTRIP_N","INTRUDER_N",
+	/*R0-R7*/	"SPI_BMC_BOOT_CS1_R_N","FM_CPU_MEMHOT_LVC3_N",
+				"DBP_CPU_PREQ_N","FM_CPU_ERR2_LVT3_BMC_N",
+				"RISER_NCSI_EN_N","","LOM_NCSI_EN_N","OCP_NCSI_EN_N",
+	/*S0-S7*/	"BMC_XDP_PRDY_N","SIO_POWER_GOOD","BMC_PWR_DEBUG_R_N","BMC_DEBUG_EN_R_N","",
+				"GPIOS5_BMC","","GPIOS7_BMC",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","BMC_DET_UID_N","BMC_JTAG_SEL","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"XDP_PRESENT_N","DBP_SYSPWROK","BMC_JTAG_SEL","FM_SMI_ACTIVE_N","",
+				"GPIOZ5","","",
+	/*AA0-AA7*/	"FP_BMC_SYSLED_N","PS_PWROK","RST_PLTRST_BMC_N","HDA_SDO_BMC",
+				"FM_SLPS4_R_N","","POWER_BUTTON","POWER_OUT",
+	/*AB0-AB7*/	"RESET_OUT","RESET_BUTTON","BIOS_REFLASH","POST_COMPLETE","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&i2c0 {
+	/* FP_LCD */
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+		label = "fru";
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	tmp112@48 {
+		compatible = "ti,tmp112";
+		reg = <0x48>;
+		label = "inlet";
+	};
+
+	tmp112@49 {
+		compatible = "ti,tmp112";
+		reg = <0x49>;
+		label = "outlet";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9548";
+		reg = <0x72>;
+	};
+};
+
+&i2c4 {
+	/* IPMB */
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	adm1278@33 {
+		compatible = "adi,adm1293";
+		reg = <0x33>;
+	};
+
+	adm1278@32 {
+		compatible = "adi,adm1293";
+		reg = <0x32>;
+	};
+
+	adm1278@20 {
+		compatible = "adi,adm1293";
+		reg = <0x20>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	pca0: pca9555@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	pca1: pca9555@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	pca2: pca9555@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	pca3: pca9555@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+};
+
+&i2c9 {
+	/* cpld */
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+
+	pca4: pca9555@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	pca5: pca9555@25 {
+		compatible = "nxp,pca9555";
+		reg = <0x25>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	power-supply@58 {
+		compatible = "inspur,ipsps1";
+		reg = <0x58>;
+	};
+
+	power-supply@59 {
+		compatible = "inspur,ipsps1";
+		reg = <0x59>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+		&pinctrl_pwm2_default &pinctrl_pwm3_default
+		&pinctrl_pwm4_default &pinctrl_pwm5_default
+		&pinctrl_pwm6_default &pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x01>;
+	};
+
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x03>;
+	};
+
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x05>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x07>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08 0x09>;
+	};
+
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a 0x0b>;
+	};
+
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c 0x0d>;
+	};
+
+	fan@7 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e 0x0f>;
+	};
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&kcs4 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca4>;
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+	 &pinctrl_adc2_default &pinctrl_adc3_default &pinctrl_adc4_default
+	 &pinctrl_adc5_default &pinctrl_adc6_default &pinctrl_adc7_default
+	 &pinctrl_adc8_default &pinctrl_adc9_default &pinctrl_adc10_default
+	 &pinctrl_adc11_default &pinctrl_adc12_default &pinctrl_adc13_default
+	 &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vuart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-on5263m5.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-on5263m5.dts
index 80c92e065a10..5a98a19f445e 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-on5263m5.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-on5263m5.dts
@@ -11,7 +11,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "earlyprintk";
+		bootargs = "earlycon";
 	};
 
 	memory {
diff --git a/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-s2600wf.dts
index 1deb30ec912c..d5b7d28cda88 100644
--- a/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-s2600wf.dts
@@ -10,7 +10,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "earlyprintk";
+		bootargs = "earlycon";
 	};
 
 	memory@80000000 {
@@ -22,9 +22,9 @@
 		#size-cells = <1>;
 		ranges;
 
-		vga_memory: framebuffer@7f000000 {
+		vga_memory: framebuffer@9f000000 {
 			no-map;
-			reg = <0x7f000000 0x01000000>;
+			reg = <0x9f000000 0x01000000>; /* 16M */
 		};
 	};
 
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-starscream.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-starscream.dts
new file mode 100644
index 000000000000..ec82af94e1fb
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-starscream.dts
@@ -0,0 +1,389 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 Inventec Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "STARSCREAM BMC";
+	compatible = "inventec,starscream-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-uid {
+			label = "UID_LED";
+			gpios = <&gpio0 186 GPIO_ACTIVE_LOW>;
+		};
+
+		led-heartbeat {
+			label = "HB_LED";
+			gpios = <&gpio0 127 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+#include "openbmc-flash-layout.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc2";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+&i2c1 {
+	status = "okay";
+};
+&i2c2 {
+	status = "okay";
+};
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	// I2C EXPANDER
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			// AMD SB-TSI CPU1
+			sbtsi@4c {
+				compatible = "amd,sbtsi";
+				reg = <0x4c>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			// AMD SB-TSI CPU2
+			sbtsi@48 {
+				compatible = "amd,sbtsi";
+				reg = <0x48>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	// I2C EXPANDER U153
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		usb_hub: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		riser1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		riser2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	// Motherboard Temp_U89
+	temperature-sensor@4e {
+		compatible = "ti,tmp421";
+		reg = <0x4e>;
+	};
+
+	// RunBMC Temp_U6
+	temperature-sensor@49 {
+		compatible = "ti,tmp75";
+		reg = <0x49>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	// I2C EXPANDER U40
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	// FRU RunBMC
+	eeprom@51 {
+		compatible = "atmel,24c512";
+		reg = <0x51>;
+		pagesize = <128>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+	// FRU SCM
+	eeprom@51 {
+		compatible = "atmel,24c512";
+		reg = <0x51>;
+		pagesize = <128>;
+	};
+
+	// SCM Temp_U17
+	temperature-sensor@4f {
+		compatible = "ti,tmp75";
+		reg = <0x4f>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/   "","","","","","","","",
+	/*B0-B7*/   "alert-psu0-smb-r-n","bmc-ready","","assert-cpu0-prochot-r-n",
+	"","","","",
+	/*C0-C7*/   "","","","","","","","",
+	/*D0-D7*/   "","","","","","","","",
+	/*E0-E7*/   "","","","","","","","",
+	/*F0-F7*/   "","","","","reset-sgpio-r-n","","","",
+	/*G0-G7*/   "","","scm-jtag-mux-select","","","","","",
+	/*H0-H7*/   "","","","","reset-out","power-out","","",
+	/*I0-I7*/   "","","","","","","irq-bmc-cpu0-buf-nmi-n","",
+	/*J0-J7*/   "","","","","","","","",
+	/*K0-K7*/   "","","","","","","","",
+	/*L0-L7*/   "","","","","","","","",
+	/*M0-M7*/   "","","","","","","","",
+	/*N0-N7*/   "","","ncsi-ocp-clk-en-n","","","","","",
+	/*O0-O7*/   "","","","","","","cpu1-thermal-trip-n","",
+	/*P0-P7*/   "","","","","","","","",
+	/*Q0-Q7*/   "cpu0-prochot-n","","cpu1-prochot-n","","cpu0-pe-rst0","","","",
+	/*R0-R7*/   "","","","","","","","",
+	/*S0-S7*/   "","","","",
+	"","PCH_SLP_S4_BMC_N","cpu0-thermtrip-n","alert-psu1-smb-r-n",
+	/*T0-T7*/   "","","","","","","","",
+	/*U0-U7*/   "","","","","","","","",
+	/*V0-V7*/   "bios-recovery-buf-n","","assert-cpu1-prochot-r-n","",
+	"power-chassis-good","","","",
+	/*W0-W7*/   "","","","","","","","",
+	/*X0-X7*/   "","","","","platform-type","","","",
+	/*Y0-Y7*/   "","","","","","","","",
+	/*Z0-Z7*/   "","cpld-power-break-n","","","","","","",
+	/*AA0-AA7*/ "","","","","","","","",
+	/*AB0-AB7*/ "","","","","","","","",
+	/*AC0-AC7*/ "","","","","","","","";
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <64>;
+	bus-frequency = <1000000>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+	non-removable;
+	max-frequency = <52000000>;
+	bus-width = <8>;
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+	aspeed,vhub-downstream-ports = <7>;
+	aspeed,vhub-generic-endpoints = <21>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb2ad_default>;
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts
new file mode 100644
index 000000000000..c713cb7a6187
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts
@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2021 Inventec Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+       model = "TRANSFORMERS BMC";
+       compatible = "inventec,transformer-bmc", "aspeed,ast2600";
+
+       aliases {
+               serial4 = &uart5;
+       };
+
+       chosen {
+               stdout-path = &uart5;
+               bootargs = "console=ttyS4,115200n8";
+       };
+
+       memory@80000000 {
+               device_type = "memory";
+               reg = <0x80000000 0x80000000>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               // UID led
+               uid {
+                       label = "UID_LED";
+                       gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+               };
+
+               // Heart beat led
+               heartbeat {
+                       label = "HB_LED";
+                       gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       ethphy0: ethernet-phy@0 {
+               compatible = "ethernet-phy-ieee802.3-c22";
+               reg = <1>;
+       };
+};
+
+&mac3 {
+       status = "okay";
+       phy-mode = "rgmii";
+       phy-handle = <&ethphy0>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&fmc {
+       status = "okay";
+
+       flash@0 {
+               status = "okay";
+               m25p,fast-read;
+               label = "bmc";
+               spi-max-frequency = <33000000>;
+               spi-tx-bus-width = <2>;
+               spi-rx-bus-width = <2>;
+#include "openbmc-flash-layout.dtsi"
+       };
+
+       flash@1 {
+               status = "okay";
+               m25p,fast-read;
+               label = "bmc2";
+               spi-max-frequency = <33000000>;
+               spi-tx-bus-width = <2>;
+               spi-rx-bus-width = <2>;
+       };
+};
+
+&spi1 {
+       status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_spi1_default>;
+
+       flash@0 {
+               status = "okay";
+               m25p,fast-read;
+               label = "bios";
+               spi-max-frequency = <33000000>;
+               spi-tx-bus-width = <1>;
+               spi-rx-bus-width = <1>;
+       };
+};
+
+&wdt1 {
+       status = "okay";
+};
+
+&uart1 {
+       status = "okay";
+};
+
+&uart5 {
+       status = "okay";
+};
+
+&i2c0 {
+       status = "okay";
+
+       //Set bmc' slave address;
+       bmc_slave@10 {
+               compatible = "ipmb-dev";
+               reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+               i2c-protocol;
+       };
+};
+
+&i2c2 {
+       status = "okay";
+};
+
+&i2c3 {
+       // FRU AT24C512C-SSHM-T
+       status = "okay";
+       eeprom@50 {
+               compatible = "atmel,24c512";
+               reg = <0x50>;
+               pagesize = <128>;
+       };
+};
+
+&i2c5 {
+       status = "okay";
+};
+
+&i2c6 {
+       status = "okay";
+
+       tmp75@49 {
+               compatible = "ti,tmp75";
+               reg = <0x49>;
+       };
+
+       tmp75@4f {
+               compatible = "ti,tmp75";
+               reg = <0x4f>;
+       };
+
+       tmp468@48 {
+               compatible = "ti,tmp468";
+               reg = <0x48>;
+       };
+};
+
+&i2c7 {
+       status = "okay";
+       adm1278@40 {
+               compatible = "adi,adm1278";
+               reg = <0x40>;
+       };
+};
+
+
+&i2c8 {
+       // FRU AT24C512C-SSHM-T
+       status = "okay";
+
+       eeprom@51 {
+               compatible = "atmel,24c512";
+               reg = <0x51>;
+               pagesize = <128>;
+       };
+
+       eeprom@53 {
+               compatible = "atmel,24c512";
+               reg = <0x53>;
+               pagesize = <128>;
+       };
+};
+
+&i2c9 {
+       // M.2
+       status = "okay";
+};
+
+&i2c10 {
+       // I2C EXPANDER
+       status = "okay";
+
+       i2c-mux@71 {
+               compatible = "nxp,pca9544";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0x71>;
+       };
+
+       i2c-mux@73 {
+               compatible = "nxp,pca9544";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0x73>;
+       };
+};
+
+&i2c11 {
+       // I2C EXPANDER
+       status = "okay";
+
+       i2c-mux@70 {
+               compatible = "nxp,pca9544";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0x70>;
+
+               pcie_eeprom_riser1: i2c@0 {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       reg = <0>;
+
+                       eeprom@55 {
+                               compatible = "atmel,24c512";
+                               reg = <0x55>;
+                               pagesize = <128>;
+                       };
+               };
+
+               pcie_eeprom_riser2: i2c@1 {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       reg = <1>;
+
+                       eeprom@55 {
+                               compatible = "atmel,24c512";
+                               reg = <0x55>;
+                               pagesize = <128>;
+                       };
+               };
+
+               pcie_eeprom_riser3: i2c@2 {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       reg = <2>;
+
+                       eeprom@55 {
+                               compatible = "atmel,24c512";
+                               reg = <0x55>;
+                               pagesize = <128>;
+                       };
+               };
+       };
+};
+
+&i2c12 {
+       status = "okay";
+
+       psu0:psu0@58 {
+               compatible = "pmbus";
+               reg = <0x58>;
+       };
+};
+
+&gpio0 {
+       status = "okay";
+       gpio-line-names =
+       /*A0-A7*/   "","","","","","","","",
+       /*B0-B7*/   "presence-ps0","power-chassis-good","","","","","presence-ps1","",
+       /*C0-C7*/   "","","","","","","","",
+       /*D0-D7*/   "","","","","","","","",
+       /*E0-E7*/   "","","","","","","","",
+       /*F0-F7*/   "","","","","power-chassis-control","","","",
+       /*G0-G7*/   "","","jtag-mux","","","","","",
+       /*H0-H7*/   "","","","","reset-button","power-button","","",
+       /*I0-I7*/   "","","","","","","","",
+       /*J0-J7*/   "","","","","","","","",
+       /*K0-K7*/   "","","","","","","","",
+       /*L0-L7*/   "","","","","","","","",
+       /*M0-M7*/   "","","","","","","","",
+       /*N0-N7*/   "","","","","","","","",
+       /*O0-O7*/   "","","","","","","","",
+       /*P0-P7*/   "","","","tck-mux","","","","",
+       /*Q0-Q7*/   "","","","","","","","",
+       /*R0-R7*/   "","","","","","","","",
+       /*S0-S7*/   "","","","","","","","",
+       /*T0-T7*/   "","","","","","","","",
+       /*U0-U7*/   "","nmi-button","","","","","","",
+       /*V0-V7*/   "","","","","power-config-full-load","","","",
+       /*W0-W7*/   "","","","","","","","",
+       /*X0-X7*/   "","","","","","","","",
+       /*Y0-Y7*/   "","","","","","","","",
+       /*Z0-Z7*/   "","","","","","","","",
+       /*AA0-AA7*/ "","","","","","","","",
+       /*AB0-AB7*/ "","","","","","","","",
+       /*AC0-AC7*/ "","","","","","","","";
+};
+
+&lpc_snoop {
+       status = "okay";
+       snoop-ports = <0x80>;
+};
+
+&emmc_controller {
+       status = "okay";
+};
+
+&emmc {
+       status = "okay";
+       non-removable;
+       max-frequency = <52000000>;
+       bus-width = <8>;
+};
+
+&vhub {
+       status = "okay";
+       aspeed,vhub-downstream-ports = <7>;
+       aspeed,vhub-generic-endpoints = <21>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_usb2ad_default>;
+};
+
+&rtc {
+       status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr630.dts
index c29e5f4d86ad..ddbcbc64e235 100644
--- a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr630.dts
@@ -27,7 +27,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
+		bootargs = "console=tty0 console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -208,7 +208,7 @@
 	 *	Slot 3
 	 */
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9545";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -249,7 +249,7 @@
 	 *	Slot 2,
 	 *	Slot 3
 	 */
-	i2c-switch@76 {
+	i2c-mux@76 {
 		compatible = "nxp,pca9546";
 		reg = <0x76>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr855xg2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr855xg2.dts
index 084c455ad4cb..6045b60b80da 100644
--- a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr855xg2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr855xg2.dts
@@ -27,7 +27,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
+		bootargs = "console=tty0 console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -175,7 +175,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9545";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -227,7 +227,7 @@
 
 &i2c3 {
 	status = "okay";
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-microsoft-olympus.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-microsoft-olympus.dts
index 73319917cb74..3ef8358ff764 100644
--- a/arch/arm/boot/dts/aspeed-bmc-microsoft-olympus.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-microsoft-olympus.dts
@@ -11,7 +11,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@40000000 {
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-lanyang.dts
index 42b37a204241..c0847636f20b 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-lanyang.dts
@@ -11,7 +11,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-mowgli.dts
index f7e935ede919..31ff19ef87a0 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-mowgli.dts
@@ -5,13 +5,13 @@
 #include <dt-bindings/leds/leds-pca955x.h>
 
 / {
-	model = "Mihawk BMC";
-	compatible = "ibm,mihawk-bmc", "aspeed,ast2500";
+	model = "Mowgli BMC";
+	compatible = "ibm,mowgli-bmc", "aspeed,ast2500";
 
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -46,30 +46,31 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 6)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 2)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 0)>;
 		};
-		id-button {
+
+		button-id {
 			label = "id-button";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -80,76 +81,58 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca9552 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca9552 10 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca9552 11 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
-
-		fan5-presence {
-			label = "fan5-presence";
-			gpios = <&pca9552 14 GPIO_ACTIVE_LOW>;
-			linux,code = <14>;
-		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		fault {
+		front-fault {
 			retain-state-shutdown;
 			default-state = "keep";
 			gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		power-button {
 			retain-state-shutdown;
 			default-state = "keep";
 			gpios = <&gpio ASPEED_GPIO(AA, 1) GPIO_ACTIVE_LOW>;
 		};
 
-		rear-id {
+		front-id {
 			retain-state-shutdown;
 			default-state = "keep";
 			gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_LOW>;
 		};
 
-		rear-g {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&gpio ASPEED_GPIO(AA, 4) GPIO_ACTIVE_LOW>;
-		};
-
-		rear-ok {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&gpio ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
-		};
-
 		fan0 {
 			retain-state-shutdown;
 			default-state = "keep";
@@ -179,12 +162,6 @@
 			default-state = "keep";
 			gpios = <&pca9552 4 GPIO_ACTIVE_LOW>;
 		};
-
-		fan5 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 5 GPIO_ACTIVE_LOW>;
-		};
 	};
 
 	fsi: gpio-fsi {
@@ -195,10 +172,11 @@
 
 		clock-gpios = <&gpio ASPEED_GPIO(E, 6) GPIO_ACTIVE_HIGH>;
 		data-gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_HIGH>;
-		mux-gpios = <&gpio ASPEED_GPIO(E, 5) GPIO_ACTIVE_HIGH>;
+		mux-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
 		enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
-		trans-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
+		trans-gpios = <&gpio ASPEED_GPIO(E, 5) GPIO_ACTIVE_HIGH>;
 	};
+
 	iio-hwmon-12v {
 		compatible = "iio-hwmon";
 		io-channels = <&adc 0>;
@@ -214,46 +192,26 @@
 		io-channels = <&adc 2>;
 	};
 
-	iio-hwmon-vdd0 {
+	iio-hwmon-vdd {
 		compatible = "iio-hwmon";
 		io-channels = <&adc 3>;
 	};
 
-	iio-hwmon-vdd1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 4>;
-	};
-
-	iio-hwmon-vcs0 {
+	iio-hwmon-vcs {
 		compatible = "iio-hwmon";
 		io-channels = <&adc 5>;
 	};
 
-	iio-hwmon-vcs1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 6>;
-	};
-
-	iio-hwmon-vdn0 {
+	iio-hwmon-vdn {
 		compatible = "iio-hwmon";
 		io-channels = <&adc 7>;
 	};
 
-	iio-hwmon-vdn1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 8>;
-	};
-
-	iio-hwmon-vio0 {
+	iio-hwmon-vio {
 		compatible = "iio-hwmon";
 		io-channels = <&adc 9>;
 	};
 
-	iio-hwmon-vio1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 10>;
-	};
-
 	iio-hwmon-vddra {
 		compatible = "iio-hwmon";
 		io-channels = <&adc 11>;
@@ -268,16 +226,6 @@
 		compatible = "iio-hwmon";
 		io-channels = <&adc 13>;
 	};
-
-	iio-hwmon-vddrc {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 14>;
-	};
-
-	iio-hwmon-vddrd {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 15>;
-	};
 };
 
 &pwm_tacho {
@@ -285,7 +233,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
 		&pinctrl_pwm2_default &pinctrl_pwm3_default
-		&pinctrl_pwm4_default &pinctrl_pwm5_default>;
+		&pinctrl_pwm4_default>;
 
 	fan@0 {
 		reg = <0x00>;
@@ -313,38 +261,28 @@
 	};
 
 	fan@5 {
-		reg = <0x05>;
+		reg = <0x00>;
 		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
 	};
 
 	fan@6 {
-		reg = <0x00>;
+		reg = <0x01>;
 		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
 	};
 
 	fan@7 {
-		reg = <0x01>;
+		reg = <0x02>;
 		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
 	};
 
 	fan@8 {
-		reg = <0x02>;
+		reg = <0x03>;
 		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
 	};
 
 	fan@9 {
-		reg = <0x03>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
-	};
-
-	fan@10 {
 		reg = <0x04>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
-	};
-
-	fan@11 {
-		reg = <0x05>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
 	};
 };
 
@@ -463,7 +401,12 @@
 };
 
 &i2c0 {
-	status = "disabled";
+	status = "okay";
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
 };
 
 &i2c1 {
@@ -473,8 +416,7 @@
 &i2c2 {
 	status = "okay";
 
-	/* SAMTEC P0 */
-	/* SAMTEC P1 */
+	/* CPU MFG CONN */
 
 };
 
@@ -486,23 +428,11 @@
 
 	/* PCA9516 (repeater) ->
 	 *    CLK Buffer 9FGS9092
-	 *    CLK Buffer 9DBL0651BKILFT
-	 *    CLK Buffer 9DBL0651BKILFT
 	 *    Power Supply 0
 	 *    Power Supply 1
 	 *    PCA 9552 LED
 	 */
 
-	power-supply@58 {
-		compatible = "ibm,cffps1";
-		reg = <0x58>;
-	};
-
-	power-supply@5b {
-		compatible = "ibm,cffps1";
-		reg = <0x5b>;
-	};
-
 	pca9552: pca9552@60 {
 		compatible = "nxp,pca9552";
 		reg = <0x60>;
@@ -575,77 +505,53 @@
 			reg = <15>;
 			type = <PCA955X_TYPE_GPIO>;
 		};
+	};
 
+	power-supply@68 {
+		compatible = "ibm,cffps1";
+		reg = <0x68>;
 	};
 
+	power-supply@69 {
+		compatible = "ibm,cffps1";
+		reg = <0x69>;
+	};
 };
 
 &i2c4 {
 	status = "okay";
 
 	/* CP0 VDD & VCS : IR35221 */
-	/* CP0 VDN : IR35221 */
-	/* CP0 VIO : IR38064 */
-	/* CP0 VDDR : PXM1330 */
+	/* CP0 VDN & VIO : IR35221 */
+	/* CP0 VDDR : IR35221 */
 
-	ir35221@70 {
+	ir35221@28 {
 		compatible = "infineon,ir35221";
-		reg = <0x70>;
+		reg = <0x28>;
 	};
 
-	ir35221@72 {
+	ir35221@29 {
 		compatible = "infineon,ir35221";
-		reg = <0x72>;
+		reg = <0x29>;
 	};
 
-};
-
-&i2c5 {
-	status = "okay";
-
-	/* CP0 VDD & VCS : IR35221 */
-	/* CP0 VDN : IR35221 */
-	/* CP0 VIO : IR38064 */
-	/* CP0 VDDR : PXM1330 */
-
-	ir35221@70 {
+	ir35221@2d {
 		compatible = "infineon,ir35221";
-		reg = <0x70>;
+		reg = <0x2d>;
 	};
 
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
+};
 
+&i2c5 {
+	status = "disabled";
 };
 
 &i2c6 {
-	status = "okay";
-
-	/* pca9548 -> NVMe1 to 8 */
-
-	pca9548@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-	};
-
+	status = "disabled";
 };
 
 &i2c7 {
-	status = "okay";
-
-	/* pca9548 -> NVMe9 to 16 */
-
-	pca9548@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-	};
-
+	status = "disabled";
 };
 
 &i2c8 {
@@ -660,99 +566,21 @@
 &i2c9 {
 	status = "okay";
 
-	/* pca9545 Riser ->
-	*	PCIe x8  Slot3
-	*	PCIe x16 slot4
-	*	PCIe x8  slot5
-	*	I2C BMC RISER PCA9554
-	*	BMC SCL/SDA PCA9554
-	*	PCA9554
-	*/
-
-	/* pca9545 ->
-	*	PCIe x16 Slot1
-	*	PCIe x8  slot2
-	*	PEX8748
-	*/
-
-	pca9545riser@70 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	pca9545@71 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x71>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
+	/* PCIe G3 x16 slot */
 };
 
 &i2c10 {
-	status = "okay";
-
-	/* pca9545 Riser ->
-	* 	PCIe x8  Slot8
-	* 	PCIe x16 slot9
-	* 	PCIe x8  slot10
-	* 	I2C BMC RISER PCA9554
-	* 	BMC SCL/SDA PCA9554
-	* 	PCA9554
-	*/
-
-	/* pca9545 ->
-	*	PCIe x16 Slot1
-	*	PCIe x8  slot2
-	*	PEX8748
-	*/
-
-	pca9545riser@70 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	pca9545@71 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x71>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
+	status = "disabled";
 };
 
 &i2c11 {
 	status = "okay";
 
+	/* CPLD */
 	/* TPM */
 	/* RTC RX8900CE */
-	/* FPGA for power sequence */
 	/* TMP275A */
 	/* TMP275A */
-	/* EMC1462 */
-
-	tpm@57 {
-		compatible = "infineon,slb9645tt";
-		reg = <0x57>;
-	};
 
 	rtc@32 {
 		compatible = "epson,rx8900";
@@ -769,95 +597,14 @@
 		reg = <0x49>;
 	};
 
-	/* chip emc1462 use emc1403 driver */
-	emc1403@4c {
-		compatible = "smsc,emc1403";
-		reg = <0x4c>;
-	};
-
 };
 
 &i2c12 {
-	status = "okay";
-
-	/* pca9545 ->
-	*	SAS BP1
-	*	SAS BP2
-	*	NVMe BP
-	*	M.2 riser
-	*/
-
-	pca9545@70 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-
-			tmp275@48 {
-				compatible = "ti,tmp275";
-				reg = <0x48>;
-			};
-		};
-
-	};
-
+	status = "disabled";
 };
 
 &i2c13 {
-	status = "okay";
-
-	/* pca9548 ->
-	*	NVMe BP
-	*	NVMe HDD17 to 24
-	*/
-
-	pca9548@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-	};
+	status = "disabled";
 };
 
 &vuart {
@@ -918,4 +665,3 @@
 };
 
 #include "ibm-power9-dual.dtsi"
-
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts
new file mode 100644
index 000000000000..ac0d666ca10e
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2019 YADRO
+/dts-v1/;
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Nicole BMC";
+	compatible = "yadro,nicole-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		flash_memory: region@98000000 {
+			no-map;
+			reg = <0x98000000 0x04000000>; /* 64M */
+		};
+
+		coldfire_memory: codefire_memory@9ef00000 {
+			reg = <0x9ef00000 0x00100000>;
+			no-map;
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			label = "platform:green:power";
+			gpios = <&gpio ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>;
+		};
+
+		identify {
+			label = "platform:blue:indicator";
+			gpios = <&gpio ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		fault {
+			label = "platform:red:fault";
+			gpios = <&gpio ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>;
+		};
+
+		attention {
+			label = "platform:yellow:alarm";
+			gpios = <&gpio ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	fsi: gpio-fsi {
+		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		#address-cells = <2>;
+		#size-cells = <0>;
+		no-gpio-delays;
+
+		memory-region = <&coldfire_memory>;
+		aspeed,sram = <&sram>;
+		aspeed,cvic = <&cvic>;
+
+		clock-gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
+		data-gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
+		mux-gpios = <&gpio ASPEED_GPIO(A, 6) GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		trans-gpios = <&gpio ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		event-checkstop {
+			label = "checkstop";
+			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(J, 2)>;
+		};
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 12>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+	flash = <&spi1>;
+};
+
+&uart1 {
+	/* Rear RS-232 connector */
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default
+			&pinctrl_nrts1_default
+			&pinctrl_ndtr1_default
+			&pinctrl_ndsr1_default
+			&pinctrl_ncts1_default
+			&pinctrl_ndcd1_default
+			&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+		 <&syscon ASPEED_CLK_MAC1RCLK>;
+	clock-names = "MACCLK", "RCLK";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+		pagesize = <64>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	/* CPU0 characterization connector */
+};
+
+&i2c3 {
+	status = "okay";
+	/* CLK GEN SI5338 */
+};
+
+&i2c4 {
+	status = "okay";
+	/* Voltage regulators for CPU0 */
+};
+
+&i2c5 {
+	status = "okay";
+	/* Voltage regulators for CPU1 */
+};
+
+&i2c6 {
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	/* CPLD */
+};
+
+&gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","cfam-reset","","","","","fsi-mux","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"fsi-enable","bmc_power_up","sys_pwrok_buf",
+			"func_mode0","func_mode1","func_mode2","","",
+	/*E0-E7*/	"","ncsi_cfg","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","checkstop","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","power-button","","","","","",
+	/*P0-P7*/	"","fsi-trans","pm_rtc_adc_en","","","","","",
+	/*Q0-Q7*/	"","","","","","","","id-button",
+	/*R0-R7*/	"","software_pwrgood","","","","","","",
+	/*S0-S7*/	"","","","","","","","seq_cont",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"fsi-clock","led-attention","fsi-data","led-fault",
+			"led-power","","","led-identify",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+
+	func_mode0 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
+	func_mode1 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
+	func_mode2 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(D, 5) GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
+	seq_cont {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
+	ncsi_cfg {
+		gpio-hog;
+		input;
+		gpios = <ASPEED_GPIO(E, 1) GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&vuart {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+			&pinctrl_adc1_default
+			&pinctrl_adc2_default
+			&pinctrl_adc3_default
+			&pinctrl_adc4_default
+			&pinctrl_adc5_default
+			&pinctrl_adc6_default
+			&pinctrl_adc7_default
+			&pinctrl_adc8_default
+			&pinctrl_adc9_default
+			&pinctrl_adc10_default
+			&pinctrl_adc11_default
+			&pinctrl_adc12_default
+			&pinctrl_adc13_default
+			&pinctrl_adc14_default
+			&pinctrl_adc15_default>;
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+#include "ibm-power9-dual.dtsi"
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-palmetto.dts
index eb4e93a57ff4..45631b47a7b3 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-palmetto.dts
@@ -10,7 +10,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@40000000 {
@@ -73,7 +73,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(P, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(P, 5)>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-romulus.dts
index edfa44fe1f75..893e621ecab1 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-romulus.dts
@@ -9,7 +9,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -87,7 +87,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
@@ -231,23 +231,52 @@
 };
 
 &gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","cfam-reset","","","","","fsi-mux","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"fsi-enable","","","nic_func_mode0","nic_func_mode1","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","power-button","","","","",
+	/*J0-J7*/	"","","checkstop","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","led-fault","",
+				"led-identify","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","id-button",
+	/*R0-R7*/	"","","fsi-trans","","","led-power","","",
+	/*S0-S7*/	"","","","","","","","seq_cont",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"fsi-clock","","fsi-data","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+
 	nic_func_mode0 {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
-		line-name = "nic_func_mode0";
 	};
 	nic_func_mode1 {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
 		output-low;
-		line-name = "nic_func_mode1";
 	};
 	seq_cont {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
 		output-low;
-		line-name = "seq_cont";
 	};
 };
 
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-swift.dts
index b8fdd2a8a2c9..bbf864f84d37 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-swift.dts
@@ -10,7 +10,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -38,37 +38,37 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 5)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(R, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(R, 7)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(N, 0)>;
 		};
 
-		oppanel-presence {
+		event-oppanel-presence {
 			label = "oppanel-presence";
 			gpios = <&gpio ASPEED_GPIO(A, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(A, 7)>;
 		};
 
-		opencapi-riser-presence {
+		event-opencapi-riser-presence {
 			label = "opencapi-riser-presence";
 			gpios = <&gpio ASPEED_GPIO(I, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(I, 0)>;
@@ -82,59 +82,57 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		scm0-presence {
+		event-scm0-presence {
 			label = "scm0-presence";
 			gpios = <&pca9552 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		scm1-presence {
+		event-scm1-presence {
 			label = "scm1-presence";
 			gpios = <&pca9552 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		cpu0vrm-presence {
+		event-cpu0vrm-presence {
 			label = "cpu0vrm-presence";
 			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		cpu1vrm-presence {
+		event-cpu1vrm-presence {
 			label = "cpu1vrm-presence";
 			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
 		};
 
-		fanboost-presence {
+		event-fanboost-presence {
 			label = "fanboost-presence";
 			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
index f02de4ab058c..3f6010ef2b86 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
@@ -4,6 +4,7 @@
 
 #include "aspeed-g6.dtsi"
 #include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
 #include <dt-bindings/leds/leds-pca955x.h>
 
 / {
@@ -12,7 +13,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200n8";
+		bootargs = "console=ttyS4,115200n8 earlycon";
 	};
 
 	memory@80000000 {
@@ -25,34 +26,37 @@
 		#size-cells = <1>;
 		ranges;
 
-		flash_memory: region@ba000000 {
+		flash_memory: region@b8000000 {
 			no-map;
 			reg = <0xb8000000 0x4000000>; /* 64M */
 		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
 
-		air-water {
-			label = "air-water";
-			gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Q, 7)>;
+		ramoops@bc000000 {
+			compatible = "ramoops";
+			reg = <0xbc000000 0x180000>; /* 16 * (3 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
 		};
 
-		checkstop {
-			label = "checkstop";
-			gpios = <&gpio0 ASPEED_GPIO(E, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(E, 3)>;
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;	/* 16M */
 		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(H, 3)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio0 ASPEED_GPIO(E, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 5)>;
@@ -61,65 +65,76 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 	};
-};
 
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout-128.dtsi"
+	iio-hwmon-dps310 {
+		compatible = "iio-hwmon";
+		io-channels = <&dps 0>;
 	};
 
-	flash@1 {
-		status = "okay";
-		m25p,fast-read;
-		label = "alt-bmc";
-		spi-max-frequency = <50000000>;
+	iio-hwmon-bmp280 {
+		compatible = "iio-hwmon";
+		io-channels = <&bmp 1>;
 	};
 };
 
-&spi1 {
+&ehci1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
+};
 
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "pnor";
-		spi-max-frequency = <100000000>;
-	};
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"fsi-mux","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"power-button","","","checkstop","","presence-ps1","","led-rear-fault",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","presence-ps0","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"led-rear-power","led-rear-id","","usb-power","","","","",
+	/*P0-P7*/	"","","","","","bmc-tpm-reset","","",
+	/*Q0-Q7*/	"cfam-reset","","","","","","","fsi-routing",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
 };
 
 &fmc {
@@ -163,11 +178,24 @@
 	use-ncsi;
 };
 
+&emmc_controller {
+	status = "okay";
+};
+
 &emmc {
 	status = "okay";
+	clk-phase-mmc-hs200 = <36>, <270>;
+};
+
+&fsim0 {
+	status = "okay";
+
 	#address-cells = <2>;
 	#size-cells = <0>;
 
+	fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+	fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
+
 	cfam@0,0 {
 		reg = <0 0>;
 		#address-cells = <1>;
@@ -415,11 +443,22 @@
 };
 
 &i2c0 {
+	multi-master;
 	status = "okay";
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
 };
 
 &i2c1 {
 	status = "okay";
+
+	tpm: tpm@2e {
+		compatible = "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+	};
 };
 
 &i2c2 {
@@ -800,6 +839,10 @@
 	status = "okay";
 };
 
+&vuart2 {
+	status = "okay";
+};
+
 &lpc_ctrl {
 	status = "okay";
 	memory-region = <&flash_memory>;
@@ -820,376 +863,25 @@
 	status = "okay";
 };
 
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-
-	bmp: bmp280@77 {
-		compatible = "bosch,bmp280";
-		reg = <0x77>;
-		#io-channel-cells = <1>;
-	};
-
-	max31785@52 {
-		compatible = "maxim,max31785a";
-		reg = <0x52>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fan@0 {
-			compatible = "pmbus-fan";
-			reg = <0>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@1 {
-			compatible = "pmbus-fan";
-			reg = <1>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@2 {
-			compatible = "pmbus-fan";
-			reg = <2>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@3 {
-			compatible = "pmbus-fan";
-			reg = <3>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-	};
-
-	dps: dps310@76 {
-		compatible = "infineon,dps310";
-		reg = <0x76>;
-		#io-channel-cells = <0>;
-	};
-
-	pca0: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-	};
-
-	power-supply@68 {
-		compatible = "ibm,cffps1";
-		reg = <0x68>;
-	};
-
-	power-supply@69 {
-		compatible = "ibm,cffps1";
-		reg = <0x69>;
-	};
-};
-
-&i2c4 {
-	status = "okay";
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	ir35221@70 {
-		compatible = "infineon,ir35221";
-		reg = <0x70>;
-	};
-
-	ir35221@71 {
-		compatible = "infineon,ir35221";
-		reg = <0x71>;
-	};
-};
-
-&i2c5 {
-	status = "okay";
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	ir35221@70 {
-		compatible = "infineon,ir35221";
-		reg = <0x70>;
-	};
-
-	ir35221@71 {
-		compatible = "infineon,ir35221";
-		reg = <0x71>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
+&pinctrl {
+	/* Hog these as no driver is probed for the entire LPC block */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpc_default>,
+		    <&pinctrl_lsirq_default>;
 };
 
-&i2c9 {
+&xdma {
 	status = "okay";
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
+	memory-region = <&vga_memory>;
 };
 
-&i2c10 {
+&kcs2 {
 	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
 };
 
-&i2c11 {
+&kcs3 {
 	status = "okay";
-
-	pca9552: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio-line-names = "PS_SMBUS_RESET_N", "APSS_RESET_N",
-			"GPU0_TH_OVERT_N_BUFF",	"GPU1_TH_OVERT_N_BUFF",
-			"GPU2_TH_OVERT_N_BUFF", "GPU3_TH_OVERT_N_BUFF",
-			"GPU4_TH_OVERT_N_BUFF",	"GPU5_TH_OVERT_N_BUFF",
-			"GPU0_PWR_GOOD_BUFF", "GPU1_PWR_GOOD_BUFF",
-			"GPU2_PWR_GOOD_BUFF", "GPU3_PWR_GOOD_BUFF",
-			"GPU4_PWR_GOOD_BUFF", "GPU5_PWR_GOOD_BUFF",
-			"12V_BREAKER_FLT_N", "THROTTLE_UNLATCHED_N";
-
-		gpio@0 {
-			reg = <0>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-	};
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-
-	ucd90160@64 {
-		compatible = "ti,ucd90160";
-		reg = <0x64>;
-	};
-};
-
-&i2c12 {
-	status = "okay";
-};
-
-&i2c13 {
-	status = "okay";
-};
-
-&pinctrl {
-	/* Hog these as no driver is probed for the entire LPC block */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lpc_default>,
-		    <&pinctrl_lsirq_default>;
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 };
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts
index affd2c8743b1..8a7fb55ab489 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts
@@ -11,10 +11,10 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
-	memory {
+	memory@40000000 {
 		reg = <0x40000000 0x20000000>;
 	};
 
@@ -63,13 +63,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		button_checkstop {
+		event-checkstop {
 			label = "checkstop";
 			linux,code = <74>;
 			gpios = <&gpio ASPEED_GPIO(P, 5) GPIO_ACTIVE_LOW>;
 		};
 
-		button_identify {
+		event-identify {
 			label = "identify";
 			linux,code = <152>;
 			gpios = <&gpio ASPEED_GPIO(O, 7) GPIO_ACTIVE_LOW>;
@@ -107,10 +107,7 @@
 
 &mac0 {
 	status = "okay";
-
 	use-ncsi;
-	no-hw-checksum;
-
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rmii1_default>;
 };
@@ -236,3 +233,16 @@
 &wdt2 {
 	aspeed,alt-boot;
 };
+
+&sdmmc {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sd2_default>;
+	cd-inverted;
+	disable-wp;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-witherspoon.dts
index 569dad93e162..a20a532fc280 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-witherspoon.dts
@@ -10,7 +10,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -27,6 +27,12 @@
 			reg = <0x98000000 0x04000000>; /* 64M */
 		};
 
+		vga_memory: region@9f000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
 		gfx_memory: framebuffer {
 			size = <0x01000000>;
 			alignment = <0x01000000>;
@@ -45,25 +51,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 5)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(P, 7)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(N, 0)>;
@@ -77,29 +83,27 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
@@ -193,6 +197,40 @@
 
 };
 
+&gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","cfam-reset","","","","","fsi-mux","",
+	/*B0-B7*/	"","","","","","air-water","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"fsi-enable","","","","","","","",
+	/*E0-E7*/	"fsi-data","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","checkstop","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"presence-ps1","","led-rear-fault","led-rear-power",
+		        "led-rear-id","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","presence-ps0",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","fsi-trans","","","power-button","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"fsi-clock","","","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
 &fmc {
 	status = "okay";
 
@@ -658,4 +696,9 @@
 	memory-region = <&video_engine_memory>;
 };
 
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
+
 #include "ibm-power9-dual.dtsi"
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-zaius.dts
index bc60ec291681..3d2d8db73ca6 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-zaius.dts
@@ -17,7 +17,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -58,13 +58,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 7)>;
 		};
 
-		pcie-e2b-present{
+		event-pcie-e2b-present{
 			label = "pcie-e2b-present";
 			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 7)>;
@@ -231,7 +231,7 @@
 &i2c1 {
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -282,7 +282,7 @@
 &i2c4 {
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -478,32 +478,61 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpioh_unbiased>;
 
+	gpio-line-names =
+	/*A0-A7*/	"","cfam-reset","","","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"fsi-enable","","","","","led-sys-boot-status","led-attention",
+				"led-fault",
+	/*E0-E7*/	"","","","","","","","presence-pcie-e2b",
+	/*F0-F7*/	"","","","","","","","checkstop",
+	/*G0-G7*/	"fsi-clock","fsi-data","","","","","","",
+	/*H0-H7*/	"onewire0","onewire1","onewire2","onewire3","","","","",
+	/*I0-I7*/	"","","","power-button","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","iso_u164_en","","fsi-trans","",
+	/*P0-P7*/	"ncsi_mux_en_n","bmc_i2c2_sw_rst_n","","bmc_i2c5_sw_rst_n","",
+				"","fsi-mux","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","led-hdd-fault","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+
 	line_iso_u146_en {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(O, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
-		line-name = "iso_u164_en";
 	};
 
 	ncsi_mux_en_n {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
 		output-low;
-		line-name = "ncsi_mux_en_n";
 	};
 
 	line_bmc_i2c2_sw_rst_n {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
-		line-name = "bmc_i2c2_sw_rst_n";
 	};
 
 	line_bmc_i2c5_sw_rst_n {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
-		line-name = "bmc_i2c5_sw_rst_n";
 	};
 };
 
diff --git a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-portwell-neptune.dts
index 4a1ca8f5b6a7..a5e64ccc2b3a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-portwell-neptune.dts
@@ -14,7 +14,7 @@
 	};
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@80000000 {
@@ -24,17 +24,17 @@
 	leds {
 		compatible = "gpio-leds";
 		postcode0 {
-			label="BMC_UP";
+			label = "BMC_UP";
 			gpios = <&gpio ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 		postcode1 {
-			label="BMC_HB";
+			label = "BMC_HB";
 			gpios = <&gpio ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 		postcode2 {
-			label="FAULT";
+			label = "FAULT";
 			gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 		};
 		// postcode3-7 are GPIOH3-H7
@@ -121,6 +121,8 @@
 	pca9555@27 {
 		compatible = "nxp,pca9555";
 		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-qcom-dc-scm-v1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-qcom-dc-scm-v1.dts
new file mode 100644
index 000000000000..259ef3f54c5c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-qcom-dc-scm-v1.dts
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+
+/ {
+	model = "Qualcomm DC-SCM V1 BMC";
+	compatible = "qcom,dc-scm-v1-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+
+	/* Bootloader sets up the MAC to insert delay */
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+
+	use-ncsi;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <133000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <133000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <133000000>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"BMC_FLASH_MUX_SEL","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"BMC_FWSPI_RST_N","","GPIO_1_BMC_3V3","","","","","",
+	/*O0-O7*/	"JTAG_MUX_A","JTAG_MUX_B","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","SCMFPGA_SPARE_GPIO1_3V3",
+			"SCMFPGA_SPARE_GPIO2_3V3","SCMFPGA_SPARE_GPIO3_3V3",
+			"SCMFPGA_SPARE_GPIO4_3V3","SCMFPGA_SPARE_GPIO5_3V3",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*A0-A7*/	"GPI_1_BMC_1V8","","","","","",
+			"SCMFPGA_SPARE_GPIO1_1V8","SCMFPGA_SPARE_GPIO2_1V8",
+	/*B0-B7*/	"SCMFPGA_SPARE_GPIO3_1V8","SCMFPGA_SPARE_GPIO4_1V8",
+			"SCMFPGA_SPARE_GPIO5_1V8","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","BMC_SPI1_RST_N","BIOS_FLASH_MUX_SEL","",
+			"","TPM2_PIRQ_N","TPM2_RST_N","",
+	/*E0-E7*/	"","","","","","","","";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-q71l.dts
index a68ff0675c28..fed2791f5994 100644
--- a/arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-q71l.dts
@@ -28,7 +28,7 @@
 
 	chosen {
 		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlyprintk";
+		bootargs = "console=ttyS4,115200 earlycon";
 	};
 
 	memory@40000000 {
@@ -197,7 +197,7 @@
 	 *    Slot 6,
 	 *    Slot 7
 	 */
-	i2c-switch@74 {
+	i2c-mux@74 {
 		compatible = "nxp,pca9546";
 		reg = <0x74>;
 		#address-cells = <1>;
@@ -238,7 +238,7 @@
 	 *    SSD 1,
 	 *    SSD 2
 	 */
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -325,7 +325,7 @@
 	 *    PSU3
 	 *    PSU2
 	 */
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts
new file mode 100644
index 000000000000..983853eedaef
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts
@@ -0,0 +1,610 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 Quanta Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Quanta S6Q BMC";
+	compatible = "quanta,s6q-bmc", "aspeed,ast2600";
+
+	aliases {
+		// bus 0
+		i2c20 = &SMB_HOST_DB2000_3V3AUX_SCL;
+		i2c21 = &U12_PCA9546_CH1;
+		i2c22 = &SMB_HOST_DB800_B_SCL;
+		i2c23 = &SMB_HOST_DB800_C_SCL;
+
+		// bus 1
+		i2c24 = &SMB_M2_P0_1V8AUX_SCL;
+		i2c25 = &SMB_M2_P1_1V8AUX_SCL;
+		i2c26 = &SMB_CPU_PIROM_3V3AUX_SCL;
+		i2c27 = &SMB_TEMP_3V3AUX_SCL;
+		i2c28 = &SMB_IPMB_3V3AUX_SSDSB_SCL;
+		i2c29 = &SMB_IPMB_3V3AUX_SCL;
+		i2c31 = &SMB_FB_SCL;
+
+		// bus 1 - Fan board
+		i2c32 = &SMB_IOEXP_SCL;
+		i2c33 = &SMB_PROGRAM_SCL;
+		i2c34 = &SMB_FB_SCL_CH2;
+		i2c35 = &SMB_FAN_SENSE_SCL;
+
+		// bus 6
+		i2c36 = &U197_PCA9546_CH0;
+		i2c37 = &U197_PCA9546_CH1;
+		i2c38 = &U197_PCA9546_CH2;
+		i2c39 = &U197_PCA9546_CH3;
+
+		//bus 7
+		i2c40 = &SMB_OCP_SFF_3V3AUX_SCL; //OCP1
+		i2c41 = &SMB_OCP_LFF_3V3AUX_SCL; //OCP2
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			<&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		BMC_HEARTBEAT_N {
+			label = "BMC_HEARTBEAT_N";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		BMC_LED_STATUS_AMBER_N {
+			label = "BMC_LED_STATUS_AMBER_N";
+			gpios = <&gpio0 ASPEED_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		FM_ID_LED_N {
+			label = "FM_ID_LED_N";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0 - A7*/	"", "", "", "", "", "", "", "",
+	/*B0 - B7*/	"", "", "", "", "", "", "", "",
+	/*C0 - C7*/	"", "", "", "", "", "", "", "",
+	/*D0 - D7*/	"", "", "", "", "", "", "", "",
+	/*E0 - E7*/	"", "", "", "", "", "", "", "",
+	/*F0 - F7*/	"PLTRST_N", "", "PWR_DEBUG_N", "", "", "", "", "",
+	/*G0 - G7*/	"", "", "", "", "", "", "", "",
+	/*H0 - H7*/	"", "", "", "", "", "", "", "",
+	/*I0 - I7*/	"", "", "", "", "", "", "", "",
+	/*J0 - J7*/	"", "", "", "", "", "", "", "",
+	/*K0 - K7*/	"", "", "", "", "", "", "", "",
+	/*L0 - L7*/	"", "", "", "", "PREQ_N", "TCK_MUX_SEL", "", "",
+	/*M0 - M7*/	"", "", "", "PWRGD_SYS_PWROK", "", "PRDY_N", "", "",
+	/*N0 - N7*/	"", "", "", "", "", "", "", "",
+	/*O0 - O7*/	"", "", "", "", "", "", "", "",
+	/*P0 - P7*/	"SYS_BMC_PWRBTN_R_N", "SYS_PWRBTN_N", "FM_MB_RST_BTN", "RST_BMC_RSTBTN_OUT_N", "", "", "", "",
+	/*Q0 - Q7*/	"", "", "", "", "", "", "", "",
+	/*R0 - R7*/	"", "", "", "", "", "", "", "",
+	/*S0 - S7*/	"", "", "", "FP_ID_BTN_SCM_N", "", "", "", "",
+	/*T0 - T7*/	"", "", "", "", "", "", "", "",
+	/*U0 - U7*/	"", "", "", "", "", "", "", "",
+	/*V0 - V7*/	"", "", "", "", "", "SMI", "", "",
+	/*W0 - W7*/	"", "", "", "", "", "", "", "",
+	/*X0 - X7*/	"", "", "", "", "", "", "", "",
+	/*Y0 - Y7*/	"", "", "", "", "", "", "", "",
+	/*Z0 - Z7*/	"FM_BMC_READY_N", "", "", "", "", "", "", "",
+	/*AA0 - AA7*/	"", "", "", "", "", "", "", "",
+	/*AB0 - AB7*/	"", "", "", "", "", "", "", "",
+	/*AC0 - AC7*/	"", "", "", "", "", "", "", "";
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <48000>;
+	gpio-line-names =
+	/* SGPIO input lines */
+	/*IOA0-IOA7*/	"","", "SIO_POWER_GOOD","OA1", "XDP_PRST_N","", "","", "FM_SLPS3_PLD_N","", "FM_SLPS4_PLD_N","", "FM_BIOS_POST_CMPLT_BMC_N","", "FM_ADR_TRIGGER_N","OA7",
+	/*IOB0-IOB7*/	"FM_ADR_COMPLETE","", "FM_PMBUS_ALERT_B_EN","", "PSU0_PRESENT_N","", "PSU1_PRESENT_N","", "PSU0_VIN_BUF_GOOD","", "PSU01_VIN_BUF_GOOD","", "PWRGD_PS0_PWROK_R","", "PWRGD_PS1_PWROK_R","",
+	/*IOC0-IOC7*/	"PWRGD_PS_PWROK_PLD_R","", "CHASSIS_INTRUSION","", "BMC_MFG_MODE","", "FM_BMC_EN_DET_R","", "FM_ME_BT_DONE","", "CPU1_PRESENCE","", "CPU2_PRESENCE","", "IRQ_PSYS_CRIT_N","",
+	/*IOD0-IOD7*/	"","", "CPU1_THERMTRIP","", "CPU2_THERMTRIP","", "CPU1_MEM_THERM_EVENT","", "CPU2_MEM_THERM_EVENT","", "CPU1_VRHOT","", "CPU2_VRHOT","", "","",
+	/*IOE0-IOE7*/	"","", "CPU1_MEM_VRHOT","", "CPU2_MEM_VRHOT","", "","", "PCH_BMC_THERMTRIP","", "","", "","", "","",
+	/*IOF0-IOF7*/	"CPU_ERR0","", "CPU_ERR1","", "CPU_ERR2","", "","", "","", "CPU_CATERR","", "","", "","",
+	/*IOG0-IOG7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOH0-IOH7*/	"","", "FP_ID_BTN_R1_N","", "FP_RST_BTN_N","", "","", "","", "FP_PWR_BTN_PLD_N_R","", "","", "","",
+	/*IOI0-IOI7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOJ0-IOJ7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOK0-IOK7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOL0-IOL7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOM0-IOM7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*ION0-ION7*/	"","BMC_SW_HEARTBEAT_N_R", "","FP_LED_FAULT_N", "","FP_ID_LED_N", "","FM_BMC_RSTBTN_OUT_N", "","FM_THERMTRIP_DLY_LVC1_R_N", "","", "","RST_PCA9548_SENSOR_PLD_N", "","USB_OC1_REAR_N",
+	/*IOO0-IOO7*/	"","IRQ_TPM_SPI_N", "","", "","IRQ_PCH_SCI_WHEA_R_N", "","IRQ_BMC_PCH_NMI_R", "","H_CPU_NMI_LVC1_R_N", "","", "","", "","FM_JTAG_BMC_PLD_MUX_SEL",
+	/*IOP0-IOP7*/	"IP0","OP0", "","", "","", "","", "","", "","", "","", "IP7","OP7";
+};
+
+&adc0 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rmii";
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default &pinctrl_spi2cs1_default
+		&pinctrl_spi2cs2_default>;
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "spi2:0";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA0>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA2>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	U34_PWR_ADC@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+
+	U35_PWR_ADC@4b {
+		compatible = "ti,ads7830";
+		reg = <0x4b>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		SMB_HOST_DB2000_3V3AUX_SCL: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		U12_PCA9546_CH1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		SMB_HOST_DB800_B_SCL: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		SMB_HOST_DB800_C_SCL: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	i2c-mux@59 {
+		compatible = "nxp,pca9848";
+		reg = <0x59>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		SMB_M2_P0_1V8AUX_SCL: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		SMB_M2_P1_1V8AUX_SCL: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		SMB_CPU_PIROM_3V3AUX_SCL: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		SMB_TEMP_3V3AUX_SCL: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			U163_tmp75@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			U114_tmp75@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		SMB_IPMB_3V3AUX_SSDSB_SCL: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			U4_tmp75@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+			U73_tmp75@4d {
+				compatible = "ti,tmp75";
+				reg = <0x4d>;
+			};
+		};
+
+		SMB_IPMB_3V3AUX_SCL: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			U190_fru@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+				pagesize = <32>;
+			};
+		};
+
+		SMB_FB_SCL: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			i2c-mux@77 {
+				compatible = "nxp,pca9546";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+
+				SMB_IOEXP_SCL: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				SMB_PROGRAM_SCL: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				SMB_FB_SCL_CH2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				SMB_FAN_SENSE_SCL: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+
+					Current_Meter_U2@45 {
+						compatible = "ti,ina219";
+						reg = <0x45>;
+						shunt-resistor = <1000>; /* = 1 mOhm */
+					};
+
+					Current_Meter_U3@44 {
+						compatible = "ti,ina219";
+						reg = <0x44>;
+						shunt-resistor = <1000>; /* = 1 mOhm */
+					};
+
+					TEMP_sensor_U2@4b {
+						compatible = "ti,tmp75";
+						reg = <0x4b>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	bus-frequency = <400000>;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* MB FRU (U173) @ 0xA2 */
+	mb_fru: mb_fru@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+
+	/* FP_U1 Inlet */
+	FP_U1_tmp75@4a {
+		compatible = "ti,tmp75";
+		reg = <0x4a>;
+	};
+
+	FP_U4_fru@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		U197_PCA9546_CH0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		U197_PCA9546_CH1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			cpu0_pvccin@60 {
+				compatible = "isil,raa229004";
+				reg = <0x60>;
+			};
+
+			cpu0_pvccinfaon@61 {
+				compatible = "isil,isl69260";
+				reg = <0x61>;
+			};
+
+			cpu0_pvccd_hv@63 {
+				compatible = "isil,isl69260";
+				reg = <0x63>;
+			};
+		};
+
+		U197_PCA9546_CH2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			cpu1_pvccin@72 {
+				compatible = "isil,raa229004";
+				reg = <0x72>;
+			};
+
+			cpu1_pvccinfaon@74 {
+				compatible = "isil,isl69260";
+				reg = <0x74>;
+			};
+
+			cpu1_pvccd_hv@76 {
+				compatible = "isil,isl69260";
+				reg = <0x76>;
+			};
+		};
+
+		U197_PCA9546_CH3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		SMB_OCP_SFF_3V3AUX_SCL: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		SMB_OCP_LFF_3V3AUX_SCL: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+
+	/* SCM FRU (U19) @ 0xA2 */
+	scm_fru: scm_fru@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+
+	scm_tmp75_u4@4a {
+		compatible = "ti,tmp75";
+		reg = <0x4a>;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-supermicro-x11spi.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-supermicro-x11spi.dts
new file mode 100644
index 000000000000..50f3c6a5c0c8
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-supermicro-x11spi.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020 Super Micro Computer, Inc
+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+
+/ {
+	model = "X11SPI BMC";
+	compatible = "supermicro,x11spi-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@7f000000 {
+			no-map;
+			reg = <0x7f000000 0x01000000>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+
+};
+
+&gpio {
+    status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+    status = "okay";
+
+    pinctrl-names = "default";
+    pinctrl-0 = <&pinctrl_rmii1_default>;
+    clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+           <&syscon ASPEED_CLK_MAC1RCLK>;
+    clock-names = "MACCLK", "RCLK";
+    use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default
+			 &pinctrl_pwm6_default &pinctrl_pwm7_default>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s7106.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s7106.dts
new file mode 100644
index 000000000000..aff27c1d4b06
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s7106.dts
@@ -0,0 +1,528 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Tyan S7106 BMC";
+	compatible = "tyan,s7106-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		p2a_memory: region@987f0000 {
+			no-map;
+			reg = <0x987f0000 0x00010000>; /* 64KB */
+		};
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>; /* 16M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		label = "bmc";
+		status = "okay";
+		m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
+	};
+};
+
+&uart1 {
+	/* Rear RS-232 connector */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default>;
+};
+
+&uart2 {
+	/* RS-232 connector on header */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			&pinctrl_rxd2_default>;
+};
+
+&uart3 {
+	/* Alternative to vuart to internally connect (route) to uart1
+	 * when vuart cannot be used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart4 {
+	/* Alternative to vuart to internally connect (route) to the
+	 * external port usually used by uart1 when vuart cannot be
+	 * used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart5 {
+	/* BMC "debug" (console) UART; connected to RS-232 connector
+	 * on header; selectable via jumpers as alternative to uart2
+	 */
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+
+	/* We enable the VUART here, but leave it in a state that does
+	 * not interfere with the SuperIO. The goal is to have both the
+	 * VUART and the SuperIO available and decide at runtime whether
+	 * the VUART should actually be used. For that reason, configure
+	 * an "invalid" IO address and an IRQ that is not used by the
+	 * BMC.
+	 */
+
+	aspeed,lpc-io-reg = <0xffff>;
+	aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&p2a {
+	status = "okay";
+	memory-region = <&p2a_memory>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&adc {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+			&pinctrl_pwm1_default
+			&pinctrl_pwm3_default
+			&pinctrl_pwm4_default>;
+
+	/* CPU fan #0 */
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	/* CPU fan #1 */
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	/* PWM group for chassis fans #1, #2, #3 and #4  */
+	fan@2 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	/* PWM group for chassis fans #5 and #6  */
+	fan@6 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* Hardware monitor with temperature sensors */
+	nct7802@28 {
+		compatible = "nuvoton,nct7802";
+		reg = <0x28>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 { /* LTD */
+			reg = <0>;
+		};
+
+		channel@1 { /* RTD1 */
+			reg = <1>;
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@2 { /* RTD2 */
+			reg = <2>;
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@3 { /* RTD3 */
+			reg = <3>;
+			sensor-type = "temperature";
+		};
+	};
+
+	/* Also connected to:
+	 * - IPMB pin header
+	 * - CPU #0 memory error LED @ 0x3A
+	 * - CPU #1 memory error LED @ 0x3C
+	 */
+};
+
+&i2c1 {
+	/* Directly connected to PCH SMBUS #0 */
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* BMC EEPROM, incl. mainboard FRU */
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+
+	/* Also connected to:
+	 * - fan header
+	 * - mini-SAS HD connector
+	 * - SSATA SGPIO
+	 * - via switch (BMC_SMB3_PCH_IE_SML3_EN, active low)
+	 *   to PCH SMBUS #3
+	 */
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* PSU1 FRU @ 0xA0 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	/* PSU2 FRU @ 0xA2 */
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	/* PSU1 @ 0xB0 */
+	power-supply@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	/* PSU2 @ 0xB2 */
+	power-supply@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+
+	/* Also connected to:
+	 * - PCH SMBUS #1
+	 */
+};
+
+&i2c4 {
+	status = "okay";
+
+	/* Connected to:
+	 * - PCH SMBUS #2
+	 */
+
+	/* Connected via switch to:
+	 * - CPU #0 channels ABC VDDQ @ 0x80
+	 * - CPU #0 channels DEF VDDQ @ 0x81
+	 * - CPU #1 channels ABC VDDQ @ 0x82
+	 * - CPU #1 channels DEF VDDQ @ 0x83
+	 * - CPU #0 VCCIO & VMCP @ 0x52
+	 * - CPU #1 VCCIO & VMCP @ 0x53
+	 * - CPU #0 VCCIN @ 0xC0
+	 * - CPU #0 VSA @ 0xC2
+	 * - CPU #1 VCCIN @ 0xC4
+	 * - CPU #1 VSA @ 0xC6
+	 * - J110
+	 */
+};
+
+&i2c5 {
+	status = "okay";
+
+	/* Connected via switch (PCH_BMC_SMB_SW_P) to:
+	 * - mainboard FRU @ 0xAE
+	 * - XDP connector
+	 * - ME debug header
+	 * - clock buffer @ 0xD8
+	 * - i2c4 via switch (PCH_VR_SMBUS_SW_P; controlled by PCH)
+	 * - PCH SMBUS
+	 */
+};
+
+&i2c6 {
+	status = "okay";
+
+	/* Connected via switch (BMC_PE_SMB_EN_1_N) to
+	 * bus mux (selector BMC_PE_SMB_SW_BIT[1..0]) to:
+	 * - 0,0: PCIE slot 1, SMB #1
+	 * - 0,1: PCIE slot 1, SMB #2
+	 * - 1,0: PCIE slot 2, SMB #1
+	 * - 1,1: PCIE slot 2, SMB #2
+	 */
+
+	/* Connected via switch (BMC_PE_SMB_EN_2_N) to
+	 * bus mux (selector BMC_PE_SMB_SW_BIT[1..0]) to:
+	 * - 0,0: OCP0 (A) SMB
+	 * - 0,1: OCP0 (C) SMB
+	 * - 1,0: OCP1 (A) SMB
+	 * - 1,1: NC
+	 */
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* Connected to:
+	 * - PCH SMBUS #4
+	 */
+};
+
+&i2c8 {
+	status = "okay";
+
+	/* Not connected */
+};
+
+&mac0 {
+	status = "okay";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+/* We're following the GPIO naming as defined at
+ * https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md.
+ *
+ * Notes on led-identify and id-button:
+ * - A physical button is connected to id-button which
+ *   triggers the clock on a D flip-flop. The /Q output of the
+ *   flip-flop drives its D input.
+ * - The flip-flop's Q output drives led-identify which is
+ *   connected to LEDs.
+ * - With that, every button press toggles the LED between on and off.
+ *
+ * Notes on power-, reset- and nmi- button and control:
+ * - The -button signals can be used to monitor physical buttons.
+ * - The -control signals can be used to actuate the specific
+ *   operation.
+ * - In hardware, the -button signals are connected to the -control
+ *   signals through drivers with the -control signals being
+ *   protected through diodes.
+ */
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0*/		"",
+	/*A1*/		"",
+	/*A2*/		"led-identify", /* in/out: BMC_IDLED_ON_N */
+	/*A3*/		"",
+	/*A4*/		"",
+	/*A5*/		"",
+	/*A6*/		"",
+	/*A7*/		"",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0*/		"",
+	/*C1*/		"",
+	/*C2*/		"",
+	/*C3*/		"",
+	/*C4*/		"id-button", /* in/out: BMC_IDBTN_IN_OUT_N */
+	/*C5*/		"post-complete", /* in: FM_BIOS_POST_CMPLT_N */
+	/*C6*/		"",
+	/*C7*/		"",
+	/*D0*/		"",
+	/*D1*/		"",
+	/*D2*/		"power-chassis-good", /* in: SYS_PWROK_BUF */
+	/*D3*/		"platform-reset", /* in: SYS_PLTRST_N */
+	/*D4*/		"",
+	/*D5*/		"",
+	/*D6*/		"",
+	/*D7*/		"",
+	/*E0*/		"power-button", /* in: BMC_PWBTN_IN_N */
+	/*E1*/		"power-chassis-control", /* out: BMC_PWRBTN_OUT_N */
+	/*E2*/		"reset-button", /* in: BMC_RSTBTN_IN_N */
+	/*E3*/		"reset-control", /* out: BMC_RSTBTN_OUT_N */
+	/*E4*/		"nmi-button", /* in: BMC_NMIBTN_IN_N */
+	/*E5*/		"nmi-control", /* out: BMC_NMIBTN_OUT_N */
+	/*E6*/		"",
+	/*E7*/		"led-heartbeat", /* out: BMC_HEARTBRAT_LED_N */
+	/*F0*/		"",
+	/*F1*/		"clear-cmos-control", /* out: BMC_CLR_CMOS_N */
+	/*F2*/		"",
+	/*F3*/		"",
+	/*F4*/		"led-fault", /* out: AST_HW_FAULT_N */
+	/*F5*/		"",
+	/*F6*/		"",
+	/*F7*/		"",
+	/*G0*/		"BMC_PE_SMB_EN_1_N", /* out */
+	/*G1*/		"BMC_PE_SMB_EN_2_N", /* out */
+	/*G2*/		"",
+	/*G3*/		"",
+	/*G4*/		"",
+	/*G5*/		"",
+	/*G6*/		"",
+	/*G7*/		"",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0*/		"",
+	/*Q1*/		"",
+	/*Q2*/		"",
+	/*Q3*/		"",
+	/*Q4*/		"BMC_PE_SMB_SW_BIT0", /* out */
+	/*Q5*/		"BMC_PE_SMB_SW_BIT1", /* out */
+	/*Q6*/		"",
+	/*Q7*/		"",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0*/		"",
+	/*AA1*/		"",
+	/*AA2*/		"",
+	/*AA3*/		"BMC_SMB3_PCH_IE_SML3_EN", /* out */
+	/*AA4*/		"",
+	/*AA5*/		"",
+	/*AA6*/		"",
+	/*AA7*/		"",
+	/*AB0-AB7*/	"","","","","","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts
new file mode 100644
index 000000000000..f6c4549c0ac4
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts
@@ -0,0 +1,471 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Tyan S8036 BMC";
+	compatible = "tyan,s8036-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		p2a_memory: region@987f0000 {
+			no-map;
+			reg = <0x987f0000 0x00010000>; /* 64KB */
+		};
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>; /* 16M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		label = "bmc";
+		status = "okay";
+		m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
+	};
+};
+
+&uart1 {
+	/* Rear RS-232 connector */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default>;
+};
+
+&uart2 {
+	/* RS-232 connector on header */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			&pinctrl_rxd2_default>;
+};
+
+&uart3 {
+	/* Alternative to vuart to internally connect (route) to uart1
+	 * when vuart cannot be used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart4 {
+	/* Alternative to vuart to internally connect (route) to the
+	 * external port usually used by uart1 when vuart cannot be
+	 * used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart5 {
+	/* BMC "debug" (console) UART; connected to RS-232 connector
+	 * on header; selectable via jumpers as alternative to uart2
+	 */
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+
+	/* We enable the VUART here, but leave it in a state that does
+	 * not interfere with the SuperIO. The goal is to have both the
+	 * VUART and the SuperIO available and decide at runtime whether
+	 * the VUART should actually be used. For that reason, configure
+	 * an "invalid" IO address and an IRQ that is not used by the
+	 * BMC.
+	 */
+	aspeed,lpc-io-reg = <0xffff>;
+	aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&p2a {
+	status = "okay";
+	memory-region = <&p2a_memory>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&adc {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+			&pinctrl_pwm1_default
+			&pinctrl_pwm3_default
+			&pinctrl_pwm4_default>;
+
+	/* CPU fan */
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	/* PWM group for chassis fans #1, #2, #3 and #4 */
+	fan@2 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	/* PWM group for chassis fans #5 and #6  */
+	fan@6 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+};
+
+&i2c0 {
+	/* Directly connected to Sideband-Temperature Sensor Interface (APML) */
+	status = "okay";
+};
+
+&i2c1 {
+	/* Directly connected to IPMB HDR. */
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* BMC EEPROM, incl. mainboard FRU */
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+	/* Also connected to:
+	 * - BCM5720
+	 * - FPGA
+	 * - FAN HDR
+	 * - FPIO HDR
+	 */
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* PSU1 FRU @ 0xA0 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	/* PSU2 FRU @ 0xA2 */
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	/* PSU1 @ 0xB0 */
+	power-supply@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	/* PSU2 @ 0xB2 */
+	power-supply@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+	/* Hardware monitor with temperature sensors */
+	nct7802@28 {
+		compatible = "nuvoton,nct7802";
+		reg = <0x28>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 { /* LTD */
+			reg = <0>;
+			status = "okay";
+		};
+
+		channel@1 { /* RTD1 */
+			reg = <1>;
+			status = "okay";
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@2 { /* RTD2 */
+			reg = <2>;
+			status = "okay";
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@3 { /* RTD3 */
+			reg = <3>;
+			status = "okay";
+			sensor-type = "temperature";
+		};
+	};
+
+	/* Also connected to:
+	 * - PCA9544
+	 * - CLK BUFF
+	 * - OCP FRU
+	 */
+};
+
+&i2c6 {
+	status = "okay";
+	/* Connected to:
+	 * - PCA9548 @0xE0
+	 * - PCA9548 @0xE2
+	 * - PCA9544 @0xE4
+	 */
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* Connected to:
+	 * - PCH SMBUS #4
+	 */
+};
+
+&i2c8 {
+	status = "okay";
+
+	/* Not connected */
+};
+
+&mac0 {
+	status = "okay";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+/* We're following the GPIO naming as defined at
+ * https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md.
+ *
+ * Notes on led-identify and id-button:
+ * - A physical button is connected to id-button which
+ *   triggers the clock on a D flip-flop. The /Q output of the
+ *   flip-flop drives its D input.
+ * - The flip-flop's Q output drives led-identify which is
+ *   connected to LEDs.
+ * - With that, every button press toggles the LED between on and off.
+ *
+ * Notes on power-, reset- and nmi- button and control:
+ * - The -button signals can be used to monitor physical buttons.
+ * - The -control signals can be used to actuate the specific
+ *   operation.
+ * - In hardware, the -button signals are connected to the -control
+ *   signals through drivers with the -control signals being
+ *   protected through diodes.
+ */
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0*/		"",
+	/*A1*/		"",
+	/*A2*/		"led-identify", /* in/out: BMC_CHASSIS_ID_LED_L */
+	/*A3*/		"",
+	/*A4*/		"",
+	/*A5*/		"",
+	/*A6*/		"",
+	/*A7*/		"",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0*/		"",
+	/*D1*/		"",
+	/*D2*/		"power-chassis-good", /* in: PWR_GOOD_LED -- Check if this is Z3?*/
+	/*D3*/		"platform-reset", /* in: RESET_LED_L */
+	/*D4*/		"",
+	/*D5*/		"",
+	/*D6*/		"",
+	/*D7*/		"",
+	/*E0*/		"power-button", /* in: BMC_SYS_MON_PWR_BTN_L */
+	/*E1*/		"power-chassis-control", /* out: BMC_ASSERT_PWR_BTN */
+	/*E2*/		"reset-button", /* in: BMC_SYS_MOS_RST_BTN_L*/
+	/*E3*/		"reset-control", /* out: BMC_ASSERT_RST_BTN */
+	/*E4*/		"nmi-button", /* in: BMC_SYS_MON_NMI_BTN_L */
+	/*E5*/		"nmi-control", /* out: BMC_ASSERT_NMI_BTN */
+	/*E6*/		"TSI_RESERT",
+	/*E7*/		"led-heartbeat", /* out: BMC_GPIOE7 */
+	/*F0*/		"",
+	/*F1*/		"clear-cmos-control", /* out: BMC_ASSERT_CLR_CMOS_L */
+	/*F2*/		"",
+	/*F3*/		"",
+	/*F4*/		"led-fault", /* out: BMC_HWM_FAULT_LED_L */
+	/*F5*/		"BMC_SYS_FAULT_LED_L",
+	/*F6*/		"BMC_ASSERT_BIOS_WP_L",
+	/*F7*/		"",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0*/		"",
+	/*Q1*/		"",
+	/*Q2*/		"",
+	/*Q3*/		"",
+	/*Q4*/		"",
+	/*Q5*/		"",
+	/*Q6*/		"id-button", /* in: BMC_CHASSIS_ID_BTN_L */
+	/*Q7*/		"",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z2*/	"","","",
+	/*Z3*/		"post-complete", /* BMC_SYS_MON_PWROK */
+	/*Z4-Z7*/	"","","","",
+	/*AA0*/		"",
+	/*AA1*/		"",
+	/*AA2*/		"",
+	/*AA3*/		"",
+	/*AA4*/		"",
+	/*AA5*/		"",
+	/*AA6*/		"",
+	/*AA7*/		"BMC_ASSERT_BMC_READY",
+	/*AB0*/		"BMC_SPD_SEL",
+	/*AB1-AB7*/	"","","","","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ufispace-ncplite.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ufispace-ncplite.dts
new file mode 100644
index 000000000000..7ab29129d1e4
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ufispace-ncplite.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2022 Ufispace Co., Ltd.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ufispace NCPLite BMC";
+	compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			      <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		fan-status-int-l {
+			label = "fan-status-int-l";
+			gpios = <&gpio0 ASPEED_GPIO(M, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(M, 2)>;
+		};
+
+		allpwr-good {
+			label = "allpwr-good";
+			gpios = <&gpio0 ASPEED_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(V, 4)>;
+		};
+
+		psu0-alert-n {
+			label = "psu0-alert-n";
+			gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 1)>;
+		};
+
+		psu1-alert-n {
+			label = "psu1-alert-n";
+			gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 2)>;
+		};
+
+		int-thermal-alert {
+			label = "int-thermal-alert";
+			gpios = <&gpio0 ASPEED_GPIO(P, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(P, 2)>;
+		};
+
+		cpu-caterr-l {
+			label = "cpu-caterr-l";
+			gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(N, 3)>;
+		};
+
+		cpu-thermtrip-l {
+			label = "cpu-thermtrip-l";
+			gpios = <&gpio0 ASPEED_GPIO(V, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 5)>;
+		};
+
+		psu0-presence-l {
+			label = "psu0-presence-l";
+			gpios = <&gpio0 ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(F, 6)>;
+		};
+
+		psu1-presence-l {
+			label = "psu1-presence-l";
+			gpios = <&gpio0 ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(F, 7)>;
+		};
+
+		psu0-power-ok {
+			label = "psu0-power-ok";
+			gpios = <&gpio0 ASPEED_GPIO(M, 4) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(M, 4)>;
+		};
+
+		psu1-power-ok {
+			label = "psu1-power-ok";
+			gpios = <&gpio0 ASPEED_GPIO(M, 5) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(M, 5)>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <1000>;
+
+		fan0-presence {
+			label = "fan0-presence";
+			gpios = <&fan_ioexp 2 GPIO_ACTIVE_LOW>;
+			linux,code = <2>;
+		};
+
+		fan1-presence {
+			label = "fan1-presence";
+			gpios = <&fan_ioexp 6 GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		fan2-presence {
+			label = "fan2-presence";
+			gpios = <&fan_ioexp 10 GPIO_ACTIVE_LOW>;
+			linux,code = <10>;
+		};
+
+		fan3-presence {
+			label = "fan3-presence";
+			gpios = <&fan_ioexp 14 GPIO_ACTIVE_LOW>;
+			linux,code = <14>;
+		};
+	};
+};
+
+&mac2 {
+	status = "okay";
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_reset {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&udc {
+	status = "okay";
+};
+
+&adc0 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	lm75@48 {
+		compatible = "national,lm75";
+		reg = <0x48>;
+	};
+
+	lm75@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+	};
+
+	lm86@4c {
+		compatible = "national,lm86";
+		reg = <0x4c>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	lm75@4f {
+		cpmpatible = "national,lm75";
+		reg = <0x4f>;
+	};
+
+	fan_ioexp: pca9535@20 {
+		compatible = "nxp,pca9535";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"","","presence-fan0","",
+		"","","presence-fan1","",
+		"","","presence-fan2","",
+		"","","presence-fan3","";
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <64>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <1>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <1>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+
+	lm75@4d {
+		compatible = "national,lm75";
+		reg = <0x4d>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"CPU_PWRGD","","","power-button","host0-ready","","presence-ps0","presence-ps1",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","reset-button","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"power-chassis-control0","power-chassis-control1","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","power-chassis-good","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-n110.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-n110.dts
new file mode 100644
index 000000000000..44b9853f6e63
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-n110.dts
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+/dts-v1/;
+
+#include "aspeed-bmc-vegman.dtsi"
+
+/ {
+	model = "YADRO VEGMAN N110 BMC";
+	compatible = "yadro,vegman-n110-bmc", "aspeed,ast2500";
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"CHASSIS_INTRUSION","CASE_OPEN_FAULT_RST","","","SPEAKER_BMC","FM_FORCE_BMC_UPDATE","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","","","","",
+	/*F0-F7*/	"NMI_OUT","PCIE_NIC_ALERT","","","SKT0_FAULT_LED","","RST_RGMII_PHYRST_DNP","",
+	/*G0-G7*/	"CPU_ERR2","CPU_CATERR","PCH_BMC_THERMTRIP","","IRQ_NMI_EVENT","","","",
+	/*H0-H7*/	"PWRGD_P3V3_RISER1","PWRGD_P3V3_RISER2","PWRGD_P3V3_RISER3","","MIO_BIOS_SEL","_SPI_FLASH_HOLD","_SPI_FLASH_WP","FM_240VA_STATUS",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","_SPI2_BMC_CS_SEL",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"_SPI_RMM4_LITE_CS","","","","","","","",
+	/*S0-S7*/	"_SPI2_BMC_CS1","","","IRQ_SML0_ALERT_MUX","FP_LED_STATUS_GREEN","FP_LED_STATUS_AMBER","FP_ID_LED","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"FM_BMC_PWR_BTN","SIO_POWER_GOOD","FM_BMC_PWRBTN_OUT","FM_BMC_PCH_SCI_LPC","","","","",
+	/*AA0-AA7*/	"","IRQ_SML1_PMBUS_ALERT","FM_PVCCIN_CPU0_PWR_IN_ALERT","FM_PVCCIN_CPU1_PWR_IN_ALERT","BMC_SYS_PWR_FAULT","BMC_SYS_PWR_OK","SMI","POST_COMPLETE",
+	/*AB0-AB7*/	"FM_CPU_BMCINIT","NMI_BUTTON","ID_BUTTON","PS_PWROK","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&sgpio {
+	ngpios = <80>;
+	bus-frequency = <2000000>;
+	status = "okay";
+	/* SGPIO lines. even: input, odd: output */
+	gpio-line-names =
+	/*A0-A7*/	"CPU1_PRESENCE","","CPU1_THERMTRIP","","CPU1_VRHOT","","CPU1_FIVR_FAULT","","CPU1_MEM_ABCD_VRHOT","","CPU1_MEM_EFGH_VRHOT","","","","","",
+	/*B0-B7*/	"CPU1_MISMATCH","","CPU1_MEM_THERM_EVENT","","CPU2_PRESENCE","","CPU2_THERMTRIP","","CPU2_VRHOT","","CPU2_FIVR_FAULT","","CPU2_MEM_ABCD_VRHOT","","CPU2_MEM_EFGH_VRHOT","",
+	/*C0-C7*/	"","","","","CPU2_MISMATCH","","CPU2_MEM_THERM_EVENT","","","","","","","","","",
+	/*D0-D7*/	"","","","","","","","","","","","","","","","",
+	/*E0-E7*/	"","","","","","","","","","","","","","","","",
+	/*F0-F7*/	"SGPIO_PLD_MINOR_REV_BIT0","","SGPIO_PLD_MINOR_REV_BIT1","","SGPIO_PLD_MINOR_REV_BIT2","","SGPIO_PLD_MINOR_REV_BIT3","","SGPIO_PLD_MAJOR_REV_BIT0","","SGPIO_PLD_MAJOR_REV_BIT1","","SGPIO_PLD_MAJOR_REV_BIT2","","SGPIO_PLD_MAJOR_REV_BIT3","",
+	/*G0-G7*/	"MAIN_PLD_MINOR_REV_BIT0","","MAIN_PLD_MINOR_REV_BIT1","","MAIN_PLD_MINOR_REV_BIT2","","MAIN_PLD_MINOR_REV_BIT3","","MAIN_PLD_MAJOR_REV_BIT0","","MAIN_PLD_MAJOR_REV_BIT1","","MAIN_PLD_MAJOR_REV_BIT2","","MAIN_PLD_MAJOR_REV_BIT3","",
+	/*H0-H7*/	"","","","","","","","","","","","","","","","",
+	/*I0-I7*/	"","","","","","","","","","","","","","","","",
+	/*J0-J7*/	"","","","","","","","","","","","","","","","";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	gpio@21 {
+		compatible = "nxp,pcal9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"", "", "", "", "", "", "PE_PCH_SCR_CLKREQ", "",
+		/*IO1.0-1.7*/	"", "PE_PCH_MEZ_PRSNT", "PE_PCH_MEZ_PRSNT_", "NIC_4_PE_PRSNT", "NIC_3_PE_PRSNT", "NIC_2_PE_PRSNT", "NIC_1_PE_PRSNT", "";
+	};
+	gpio@27 {
+		compatible = "nxp,pca9698";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"PWRGD_PS_PWROK", "PWRGD_DSW_PWROK", "PWRGD_P5V_AUX", "PWRGD_P3V3_AUX", "PWRGD_P5V", "PWRGD_P3V3", "PWRGD_P1V8_PCH_AUX", "PWRGD_PCH_PVNN_AUX",
+		/*IO1.0-1.7*/	"PWRGD_P1V05_PCH_AUX", "PWRGD_PCH_AUX_VRS", "PWRGD_PVCCIN_CPU0", "PWRGD_PVCCSA_CPU0", "PWRGD_PVCCIO_CPU0", "PWRGD_PVMCP_CPU0", "PWRGD_P1V0_CPU0", "PWRGD_PVDDQ_ABC_CPU0",
+		/*IO2.0-2.7*/	"PWRGD_PVPP_ABC_CPU0", "PWRGD_PVTT_ABC_CPU0", "PWRGD_PVDDQ_DEF_CPU0", "PWRGD_PVPP_DEF_CPU0", "PWRGD_PVTT_DEF_CPU0", "", "", "",
+		/*IO3.0-3.7*/	"", "", "", "", "", "", "", "",
+		/*IO4.0-4.7*/	"", "", "", "", "", "", "", "";
+	};
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	i2c-mux@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+	i2c-mux@73 {
+		compatible = "nxp,pca9545";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	i2c-mux@71 {
+		compatible = "nxp,pca9545";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x06>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01 0x08>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x09>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03 0x0A>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0B>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-rx20.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-rx20.dts
new file mode 100644
index 000000000000..b8f0b08018a3
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-rx20.dts
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+/dts-v1/;
+
+#include "aspeed-bmc-vegman.dtsi"
+
+/ {
+	model = "YADRO VEGMAN Rx20 BMC";
+	compatible = "yadro,vegman-rx20-bmc", "aspeed,ast2500";
+
+	leds {
+		compatible = "gpio-leds";
+
+		temp_alarm {
+			label = "temp:red:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 4) GPIO_ACTIVE_LOW>;
+		};
+
+		temp_ok {
+			label = "temp:green:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 5) GPIO_ACTIVE_LOW>;
+		};
+
+		psu_fault {
+			label = "psu:red:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 6) GPIO_ACTIVE_LOW>;
+		};
+
+		psu_ok {
+			label = "psu:green:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"CASE_OPEN_DNP","CASE_OPEN_FAULT_RST_DNP","BEZEL_ON_PWR_P3V3","PWM_PWRGD_EXP_EN","SPEAKER_BMC","FM_FORCE_BMC_UPDATE","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","LED_TEMP_STATUS_R","LED_TEMP_STATUS_G","LED_PWR_STATUS_R","LED_PWR_STATUS_G",
+	/*F0-F7*/	"NMI_OUT","CPU1_DISABLE_COD","","","SKT0_FAULT_LED_DNP","SKT1_FAULT_LED_DNP","RST_RGMII_PHYRST_DNP","",
+	/*G0-G7*/	"CPU_ERR2","CPU_CATERR","PCH_BMC_THERMTRIP","SPI_BMC_BOOT_HD","IRQ_NMI_EVENT","SPI_BMC_BOOT_WP","SPI_BMC_BOOT_WP1","",
+	/*H0-H7*/	"PWRGD_P3V3_RISER1","PWRGD_P3V3_RISER2","PWRGD_P3V3_RISER3","","MIO_BIOS_SEL","_SPI_FLASH_HOLD","_SPI_FLASH_WP","FM_240VA_STATUS",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"SEL_FLASH_SOFT","STATUS_SEL_BMC","","","BMC_WDT_P","ID_BUTTON","PS_PWROK","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","SPI_BIOS_ACTIVE_FLASH_SEL","STATUS_SEL_BIOS",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"_SPI_BMC_BOOT_CS1","","","","","","","",
+	/*S0-S7*/	"_SPI2_BMC_CS1","RSR_A_SMBEXP_RST_INT","RSR_B_SMBEXP_RST_INT","IRQ_SML0_ALERT_MUX","FP_LED_STATUS_GREEN","FP_LED_STATUS_AMBER","FP_ID_LED","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"FM_BMC_PWR_BTN","SIO_POWER_GOOD","FM_BMC_PWRBTN_OUT","FM_BMC_PCH_SCI_LPC","","","","",
+	/*AA0-AA7*/	"CPU_CLK_MUX_SEL","IRQ_SML1_PMBUS_ALERT","FM_PVCCIN_CPU0_PWR_IN_ALERT","FM_PVCCIN_CPU1_PWR_IN_ALERT","BMC_SYS_PWR_FAULT","BMC_SYS_PWR_OK","SMI","POST_COMPLETE",
+	/*AB0-AB7*/	"FM_CPU_BMCINIT","NMI_BUTTON","BMC_WDT_RST1","BMC_WDT_RST2","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&sgpio {
+	ngpios = <80>;
+	bus-frequency = <2000000>;
+	status = "okay";
+	/* SGPIO lines. even: input, odd: output */
+	gpio-line-names =
+	/*A0-A7*/	"CPU1_PRESENCE","","CPU1_THERMTRIP","","CPU1_VRHOT","","CPU1_FIVR_FAULT","","CPU1_MEM_ABCD_VRHOT","","CPU1_MEM_EFGH_VRHOT","","","","","",
+	/*B0-B7*/	"CPU1_MISMATCH","","CPU1_MEM_THERM_EVENT","","CPU2_PRESENCE","","CPU2_THERMTRIP","","CPU2_VRHOT","","CPU2_FIVR_FAULT","","CPU2_MEM_ABCD_VRHOT","","CPU2_MEM_EFGH_VRHOT","",
+	/*C0-C7*/	"","","","","CPU2_MISMATCH","","CPU2_MEM_THERM_EVENT","","","","","","","","","",
+	/*D0-D7*/	"","","","","","","","","","","","","","","","",
+	/*E0-E7*/	"","","","","","","","","","","","","","","","",
+	/*F0-F7*/	"SGPIO_PLD_MINOR_REV_BIT0","","SGPIO_PLD_MINOR_REV_BIT1","","SGPIO_PLD_MINOR_REV_BIT2","","SGPIO_PLD_MINOR_REV_BIT3","","SGPIO_PLD_MAJOR_REV_BIT0","","SGPIO_PLD_MAJOR_REV_BIT1","","SGPIO_PLD_MAJOR_REV_BIT2","","SGPIO_PLD_MAJOR_REV_BIT3","",
+	/*G0-G7*/	"MAIN_PLD_MINOR_REV_BIT0","","MAIN_PLD_MINOR_REV_BIT1","","MAIN_PLD_MINOR_REV_BIT2","","MAIN_PLD_MINOR_REV_BIT3","","MAIN_PLD_MAJOR_REV_BIT0","","MAIN_PLD_MAJOR_REV_BIT1","","MAIN_PLD_MAJOR_REV_BIT2","","MAIN_PLD_MAJOR_REV_BIT3","",
+	/*H0-H7*/	"","","","","","","","","","","","","","","","",
+	/*I0-I7*/	"","","","","","","","","","","","","","","","",
+	/*J0-J7*/	"","","","","","","","","","","","","","","","";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	gpio@21 {
+		compatible = "nxp,pcal9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"ETH3_CLK_REQ", "ETH2_CLK_REQ", "RSR_A_PCIE_X16_2_PRSNT", "RSR_B_PCIE_X16_2_PRSNT", "", "RSR_B_PCIE_X8_3_PRSNT", "RSR_B_PCIE_X8_4_PRSNT", "RSR_B_PCIE_X16_PRSNT_N",
+		/*IO1.0-1.7*/	"RSR_B_PCIE_X8_2_PRSNT", "RSR_B_PCIE_X8_1_PRSNT", "NIC_1_PE_BUF_PRSNT", "RSR_A_PCIE_X16_PRSNT", "RSR_A_PCIE_X8_3_PRSNT", "RSR_A_PCIE_X8_2_PRSNT", "RSR_A_PCIE_X8_1_PRSNT_N", "";
+	};
+	gpio@23 {
+		compatible = "nxp,pcal9535";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "", "", "",
+		/*IO1.0-1.7*/	"", "", "", "", "", "", "", "";
+	};
+	gpio@27 {
+		compatible = "nxp,pca9698";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"PWRGD_PS_PWROK", "PWRGD_DSW_PWROK", "PWRGD_P5V_AUX", "PWRGD_P3V3_AUX", "PWRGD_P5V", "PWRGD_P3V3", "PWRGD_P1V8_PCH_AUX", "PWRGD_PCH_PVNN_AUX",
+		/*IO1.0-1.7*/	"PWRGD_P1V05_PCH_AUX", "PWRGD_PCH_AUX_VRS", "PWRGD_PVCCIN_CPU0", "PWRGD_PVCCSA_CPU0", "PWRGD_PVCCIO_CPU0", "PWRGD_PVMCP_CPU0", "PWRGD_P1V0_CPU0", "PWRGD_PVDDQ_ABC_CPU0",
+		/*IO2.0-2.7*/	"PWRGD_PVPP_ABC_CPU0", "PWRGD_PVTT_ABC_CPU0", "PWRGD_PVDDQ_DEF_CPU0", "PWRGD_PVPP_DEF_CPU0", "PWRGD_PVTT_DEF_CPU0", "PWRGD_PVCCIN_CPU1", "PWRGD_PVCCSA_CPU1", "PWRGD_PVCCIO_CPU1",
+		/*IO3.0-3.7*/	"PWRGD_PVMCP_CPU1", "PWRGD_P1V0_CPU1", "PWRGD_PVDDQ_GHJ_CPU1", "PWRGD_PVPP_GHJ_CPU1", "PWRGD_PVTT_GHJ_CPU1", "PWRGD_PVDDQ_KLM_CPU1", "PWRGD_PVPP_KLM_CPU1", "PWRGD_PVTT_KLM_CPU1",
+		/*IO4.0-4.7*/	"PCH_PWR_RESET_N", "FM_BOARD_SKU_ID0", "FM_BOARD_SKU_ID1", "FM_BOARD_SKU_ID2", "FM_BOARD_SKU_ID3", "FM_BOARD_SKU_ID4", "FM_BOARD_REV_ID0", "FM_BOARD_REV_ID1";
+	};
+	gpio@39 {
+		compatible = "nxp,pca9554";
+		reg = <0x39>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"FAN_FAULT_0", "FAN_FAULT_1", "FAN_FAULT_2", "FAN_FAULT_3", "FAN_FAULT_4", "FAN_FAULT_5", "FAN_FAULT_6", "";
+	};
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			i2c-mux@72 {
+				compatible = "nxp,pca9548";
+				reg = <0x72>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+					at24@50 {
+						compatible = "atmel,24c64";
+						reg = <0x50>;
+						pagesize = <32>;
+						size = <8192>;
+						address-width = <16>;
+					};
+				};
+			};
+		};
+	};
+	i2c-mux@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			i2c-mux@72 {
+				compatible = "nxp,pca9548";
+				reg = <0x72>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+					at24@50 {
+						compatible = "atmel,24c64";
+						reg = <0x50>;
+						pagesize = <32>;
+						size = <8192>;
+						address-width = <16>;
+					};
+				};
+			};
+			at24@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+				size = <8192>;
+				address-width = <16>;
+			};
+		};
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default
+			 &pinctrl_pwm6_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x07>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01 0x08>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x09>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03 0x0A>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0B>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05 0x0C>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x0D>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-sx20.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-sx20.dts
new file mode 100644
index 000000000000..933ca831d375
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-sx20.dts
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+/dts-v1/;
+
+#include "aspeed-bmc-vegman.dtsi"
+
+/ {
+	model = "YADRO VEGMAN Sx20 BMC";
+	compatible = "yadro,vegman-sx20-bmc", "aspeed,ast2500";
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"CHASSIS_INTRUSION","CASE_OPEN_FAULT_RST","","","SPEAKER_BMC","FM_FORCE_BMC_UPDATE","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","","","","",
+	/*F0-F7*/	"NMI_OUT","CPU1_DISABLE_COD","","","SKT0_FAULT_LED","SKT1_FAULT_LED","RST_RGMII_PHYRST_DNP","",
+	/*G0-G7*/	"CPU_ERR2","CPU_CATERR","PCH_BMC_THERMTRIP","","IRQ_NMI_EVENT","","","",
+	/*H0-H7*/	"PWRGD_P3V3_RISER1","PWRGD_P3V3_RISER2","PWRGD_P3V3_RISER3","","MIO_BIOS_SEL","_SPI_FLASH_HOLD","_SPI_FLASH_WP","FM_240VA_STATUS",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","BMC_GPU_RISER_ID1","BMC_GPU_RISER_ID0","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","_SPI2_BMC_CS_SEL",
+	/*P0-P7*/	"","P12V_HDDS_A_EN","P12V_HDDS_B_EN","P5V_HDDS_A_EN","PWRGD_P5V_HDDS_A","P5V_HDDS_B_EN","PWRGD_P5V_HDDS_B","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"_SPI_RMM4_LITE_CS","","","","","","","",
+	/*S0-S7*/	"_SPI2_BMC_CS1","","","IRQ_SML0_ALERT_MUX","FP_LED_STATUS_GREEN","FP_LED_STATUS_AMBER","FP_ID_LED","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"FM_BMC_PWR_BTN","SIO_POWER_GOOD","FM_BMC_PWRBTN_OUT","FM_BMC_PCH_SCI_LPC","","","","",
+	/*AA0-AA7*/	"CPU_CLK_MUX_SEL","IRQ_SML1_PMBUS_ALERT","FM_PVCCIN_CPU0_PWR_IN_ALERT","FM_PVCCIN_CPU1_PWR_IN_ALERT","BMC_SYS_PWR_FAULT","BMC_SYS_PWR_OK","SMI","POST_COMPLETE",
+	/*AB0-AB7*/	"FM_CPU_BMCINIT","NMI_BUTTON","ID_BUTTON","PS_PWROK","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&sgpio {
+	ngpios = <80>;
+	bus-frequency = <2000000>;
+	status = "okay";
+	/* SGPIO lines. even: input, odd: output */
+	gpio-line-names =
+	/*A0-A7*/	"CPU1_PRESENCE","","CPU1_THERMTRIP","","CPU1_VRHOT","","CPU1_FIVR_FAULT","","CPU1_MEM_ABCD_VRHOT","","CPU1_MEM_EFGH_VRHOT","","","","","",
+	/*B0-B7*/	"CPU1_MISMATCH","","CPU1_MEM_THERM_EVENT","","CPU2_PRESENCE","","CPU2_THERMTRIP","","CPU2_VRHOT","","CPU2_FIVR_FAULT","","CPU2_MEM_ABCD_VRHOT","","CPU2_MEM_EFGH_VRHOT","",
+	/*C0-C7*/	"","","","","CPU2_MISMATCH","","CPU2_MEM_THERM_EVENT","","","","","","","","","",
+	/*D0-D7*/	"","","","","","","","","","","","","","","","",
+	/*E0-E7*/	"","","","","","","","","","","","","","","","",
+	/*F0-F7*/	"SGPIO_PLD_MINOR_REV_BIT0","","SGPIO_PLD_MINOR_REV_BIT1","","SGPIO_PLD_MINOR_REV_BIT2","","SGPIO_PLD_MINOR_REV_BIT3","","SGPIO_PLD_MAJOR_REV_BIT0","","SGPIO_PLD_MAJOR_REV_BIT1","","SGPIO_PLD_MAJOR_REV_BIT2","","SGPIO_PLD_MAJOR_REV_BIT3","",
+	/*G0-G7*/	"MAIN_PLD_MINOR_REV_BIT0","","MAIN_PLD_MINOR_REV_BIT1","","MAIN_PLD_MINOR_REV_BIT2","","MAIN_PLD_MINOR_REV_BIT3","","MAIN_PLD_MAJOR_REV_BIT0","","MAIN_PLD_MAJOR_REV_BIT1","","MAIN_PLD_MAJOR_REV_BIT2","","MAIN_PLD_MAJOR_REV_BIT3","",
+	/*H0-H7*/	"","","","","","","","","","","","","","","","",
+	/*I0-I7*/	"","","","","","","","","","","","","","","","",
+	/*J0-J7*/	"","","","","","","","","","","","","","","","";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	gpio@21 {
+		compatible = "nxp,pcal9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"", "", "CPU1_PE3_0_SLOT_PRSNT", "", "CPU1_PE1_GPU_PRSNT", "CPU1_PE3_1_SLOT_PRSNT", "PE_PCH_MEZ_PRSNT", "CPU0_PE3_1_SLOT_PRSNT",
+		/*IO1.0-1.7*/	"CPU0_PE1_GPU_PRSNT", "CPU0_PE2_NVME2_PRSNT", "CPU1_PE2_NVME3_PRSNT", "CPU1_PE2_SLOT_PRSNT", "CPU1_PE2_NVME4_PRSNT", "", "CPU0_PE2_NVME1_PRSNT", "CPU0_PE3_0_RAID_PRSNT";
+	};
+	gpio@27 {
+		compatible = "nxp,pca9698";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"PWRGD_PS_PWROK", "PWRGD_DSW_PWROK", "PWRGD_P5V_AUX", "PWRGD_P3V3_AUX", "PWRGD_P5V", "PWRGD_P3V3", "PWRGD_P1V8_PCH_AUX", "PWRGD_PCH_PVNN_AUX",
+		/*IO1.0-1.7*/	"PWRGD_P1V05_PCH_AUX", "PWRGD_PCH_AUX_VRS", "PWRGD_PVCCIN_CPU0", "PWRGD_PVCCSA_CPU0", "PWRGD_PVCCIO_CPU0", "PWRGD_PVMCP_CPU0", "PWRGD_P1V0_CPU0", "PWRGD_PVDDQ_ABC_CPU0",
+		/*IO2.0-2.7*/	"PWRGD_PVPP_ABC_CPU0", "PWRGD_PVTT_ABC_CPU0", "PWRGD_PVDDQ_DEF_CPU0", "PWRGD_PVPP_DEF_CPU0", "PWRGD_PVTT_DEF_CPU0", "PWRGD_PVCCIN_CPU1", "PWRGD_PVCCSA_CPU1", "PWRGD_PVCCIO_CPU1",
+		/*IO3.0-3.7*/	"PWRGD_PVMCP_CPU1", "PWRGD_P1V0_CPU1", "PWRGD_PVDDQ_GHJ_CPU1", "PWRGD_PVPP_GHJ_CPU1", "PWRGD_PVTT_GHJ_CPU1", "PWRGD_PVDDQ_KLM_CPU1", "PWRGD_PVPP_KLM_CPU1", "PWRGD_PVTT_KLM_CPU1",
+		/*IO4.0-4.7*/	"PWRGD_P5V_HDDS_A_R", "PWRGD_P5V_HDDS_B_R", "", "", "", "", "", "";
+	};
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	i2c-mux@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+	i2c-mux@73 {
+		compatible = "nxp,pca9545";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	i2c-mux@71 {
+		compatible = "nxp,pca9545";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default
+			 &pinctrl_pwm6_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi
new file mode 100644
index 000000000000..1a5b25b2ea29
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlyprintk";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		ramoops@9eff0000{
+			compatible = "ramoops";
+			reg = <0x9eff0000 0x10000>;
+			record-size = <0x2000>;
+			console-size = <0x2000>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		identify {
+			label = "platform:blue:indicator";
+			linux,default-trigger = "heartbeat";
+			gpios = <&gpio ASPEED_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+		};
+
+		status_amber {
+			label = "platform:red:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(S, 5) GPIO_ACTIVE_LOW>;
+		};
+
+		status_green {
+			label = "platform:green:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+		};
+
+		power_fault {
+			label = "platform:red:power";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(AA, 4) GPIO_ACTIVE_LOW>;
+		};
+
+		power_ok {
+			label = "platform:green:power";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(AA, 5) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&timer 5 1000000 0>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		label = "bmc";
+		m25p,fast-read;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2ck_default
+			&pinctrl_spi2miso_default
+			&pinctrl_spi2mosi_default
+			&pinctrl_spi2cs0_default>;
+	flash@0 {
+		status = "okay";
+		label = "bios";
+		m25p,fast-read;
+	};
+};
+
+&mac0 {
+	status = "okay";
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+
+	phy-mode = "rgmii";
+	phy-handle = <&phy>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			/* KSZ9131 */
+			compatible = "ethernet-phy-id0022.1640";
+			reg = <1>;
+
+			micrel,led-mode = <0>;
+		};
+	};
+};
+
+&vhub {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&sdmmc {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sd2_default>;
+	disable-wp;
+};
+
+&timer {
+	fttmr010,pwm-outputs = <5>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_timer5_default>;
+	#pwm-cells = <3>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default
+			&pinctrl_nrts1_default
+			&pinctrl_ndtr1_default
+			&pinctrl_ndsr1_default
+			&pinctrl_ncts1_default
+			&pinctrl_ndcd1_default
+			&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+};
+
+&i2c0 {
+	/* SMB_IPMB_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c1 {
+	/* SMB_CHASSENSOR_STBY_LVC3 */
+	status = "okay";
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	status = "okay";
+};
+
+&i2c3 {
+	/* SMB_HOST_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c4 {
+	/* BMC_PMBUS2_STBY */
+	status = "okay";
+};
+
+&i2c5 {
+	/* SMB_SMLINK0_STBY_LVC3 */
+	bus-frequency = <1000000>;
+	multi-master;
+	status = "okay";
+};
+
+&i2c6 {
+	/* SMB_TEMPSENSOR_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c7 {
+	/* SMB_SM_PMB1_SML1_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c9 {
+	/* SMB_BMC_ETH3_LVC3 */
+	status = "okay";
+};
+
+&i2c10 {
+	/* SMB_BMC_ETH2_LVC3 */
+	status = "okay";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	status = "okay";
+
+	at24@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		size = <8192>;
+		address-width = <16>;
+	};
+};
+
+&i2c12 {
+	/* SMB_BMC_FAULT_EXP_LVC3 */
+	status = "okay";
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g4.dtsi
index 46c0891aac5a..530491ae5eb2 100644
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g4.dtsi
@@ -54,8 +54,7 @@
 		ranges;
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0x94
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0x94>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-fmc";
@@ -65,34 +64,42 @@
 			flash@0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@3 {
 				reg = < 3 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@4 {
 				reg = < 4 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 		};
 
 		spi: spi@1e630000 {
-			reg = < 0x1e630000 0x18
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0x18>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-spi";
@@ -102,6 +109,7 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -164,6 +172,8 @@
 			reg = <0x1e6a0000 0x300>;
 			interrupts = <5>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			aspeed,vhub-downstream-ports = <5>;
+			aspeed,vhub-generic-endpoints = <15>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2d_default>;
 			status = "disabled";
@@ -179,18 +189,26 @@
 				compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd";
 				reg = <0x1e6e2000 0x1a8>;
 				#address-cells = <1>;
-				#size-cells = <0>;
+				#size-cells = <1>;
+				ranges = <0 0x1e6e2000 0x1000>;
 				#clock-cells = <1>;
 				#reset-cells = <1>;
 
-				pinctrl: pinctrl {
-					compatible = "aspeed,ast2400-pinctrl";
-				};
-
-				p2a: p2a-control {
+				p2a: p2a-control@2c {
+					reg = <0x2c 0x4>;
 					compatible = "aspeed,ast2400-p2a-ctrl";
 					status = "disabled";
 				};
+
+				silicon-id@7c {
+					compatible = "aspeed,ast2400-silicon-id", "aspeed,silicon-id";
+					reg = <0x7c 0x4>;
+				};
+
+				pinctrl: pinctrl@80 {
+					reg = <0x80 0x18>, <0xa0 0x10>;
+					compatible = "aspeed,ast2400-pinctrl";
+				};
 			};
 
 			rng: hwrng@1e6e2078 {
@@ -214,6 +232,16 @@
 				reg = <0x1e720000 0x8000>;	// 32K
 			};
 
+			video: video@1e700000 {
+				compatible = "aspeed,ast2400-video-engine";
+				reg = <0x1e700000 0x1000>;
+				clocks = <&syscon ASPEED_CLK_GATE_VCLK>,
+					 <&syscon ASPEED_CLK_GATE_ECLK>;
+				clock-names = "vclk", "eclk";
+				interrupts = <7>;
+				status = "disabled";
+			};
+
 			sdmmc: sd-controller@1e740000 {
 				compatible = "aspeed,ast2400-sd-controller";
 				reg = <0x1e740000 0x100>;
@@ -323,61 +351,66 @@
 			};
 
 			lpc: lpc@1e789000 {
-				compatible = "aspeed,ast2400-lpc", "simple-mfd";
+				compatible = "aspeed,ast2400-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
+				reg-io-width = <4>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0x0 0x1e789000 0x1000>;
 
-				lpc_bmc: lpc-bmc@0 {
-					compatible = "aspeed,ast2400-lpc-bmc";
-					reg = <0x0 0x80>;
+				lpc_ctrl: lpc-ctrl@80 {
+					compatible = "aspeed,ast2400-lpc-ctrl";
+					reg = <0x80 0x10>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lpc_snoop: lpc-snoop@90 {
+					compatible = "aspeed,ast2400-lpc-snoop";
+					reg = <0x90 0x8>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lhc: lhc@a0 {
+					compatible = "aspeed,ast2400-lhc";
+					reg = <0xa0 0x24 0xc8 0x8>;
+				};
+
+				lpc_reset: reset-controller@98 {
+					compatible = "aspeed,ast2400-lpc-reset";
+					reg = <0x98 0x4>;
+					#reset-cells = <1>;
+				};
+
+				ibt: ibt@140 {
+					compatible = "aspeed,ast2400-ibt-bmc";
+					reg = <0x140 0x18>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
 				};
 
-				lpc_host: lpc-host@80 {
-					compatible = "aspeed,ast2400-lpc-host", "simple-mfd", "syscon";
-					reg = <0x80 0x1e0>;
-					reg-io-width = <4>;
-
-					#address-cells = <1>;
-					#size-cells = <1>;
-					ranges = <0x0 0x80 0x1e0>;
-
-					lpc_ctrl: lpc-ctrl@0 {
-						compatible = "aspeed,ast2400-lpc-ctrl";
-						reg = <0x0 0x80>;
-						clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
-						status = "disabled";
-					};
-
-					lpc_snoop: lpc-snoop@0 {
-						compatible = "aspeed,ast2400-lpc-snoop";
-						reg = <0x0 0x80>;
-						interrupts = <8>;
-						status = "disabled";
-					};
-
-					lhc: lhc@20 {
-						compatible = "aspeed,ast2400-lhc";
-						reg = <0x20 0x24 0x48 0x8>;
-					};
-
-					lpc_reset: reset-controller@18 {
-						compatible = "aspeed,ast2400-lpc-reset";
-						reg = <0x18 0x4>;
-						#reset-cells = <1>;
-					};
-
-					ibt: ibt@c0  {
-						compatible = "aspeed,ast2400-ibt-bmc";
-						reg = <0xc0 0x18>;
-						interrupts = <8>;
-						status = "disabled";
-					};
+				uart_routing: uart-routing@9c {
+					compatible = "aspeed,ast2400-uart-routing";
+					reg = <0x9c 0x4>;
+					status = "disabled";
 				};
 			};
 
+			peci0: peci-controller@1e78b000 {
+				compatible = "aspeed,ast2400-peci";
+				reg = <0x1e78b000 0x60>;
+				interrupts = <15>;
+				clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+				resets = <&syscon ASPEED_RESET_PECI>;
+				cmd-timeout-ms = <1000>;
+				clock-frequency = <1000000>;
+				status = "disabled";
+			};
+
 			uart2: serial@1e78d000 {
 				compatible = "ns16550a";
 				reg = <0x1e78d000 0x20>;
diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g5.dtsi
index a259c63fff06..04f98d1dbb97 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g5.dtsi
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0+
 #include <dt-bindings/clock/aspeed-clock.h>
+#include <dt-bindings/interrupt-controller/aspeed-scu-ic.h>
 
 / {
 	model = "Aspeed BMC";
@@ -47,13 +48,6 @@
 		reg = <0x80000000 0>;
 	};
 
-	edac: sdram@1e6e0000 {
-		compatible = "aspeed,ast2500-sdram-edac";
-		reg = <0x1e6e0000 0x174>;
-		interrupts = <0>;
-		status = "disabled";
-	};
-
 	ahb {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -61,8 +55,7 @@
 		ranges;
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-fmc";
@@ -73,25 +66,27 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi1: spi@1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x08000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -101,19 +96,20 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi2: spi@1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x38000000 0x08000000 >;
+			reg = <0x1e631000 0xc4>, <0x38000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -123,12 +119,14 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -202,6 +200,8 @@
 			reg = <0x1e6a0000 0x300>;
 			interrupts = <5>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			aspeed,vhub-downstream-ports = <5>;
+			aspeed,vhub-generic-endpoints = <15>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2ad_default>;
 			status = "disabled";
@@ -213,24 +213,46 @@
 			#size-cells = <1>;
 			ranges;
 
+			edac: memory-controller@1e6e0000 {
+				compatible = "aspeed,ast2500-sdram-edac";
+				reg = <0x1e6e0000 0x174>;
+				interrupts = <0>;
+				status = "disabled";
+			};
+
 			syscon: syscon@1e6e2000 {
 				compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd";
 				reg = <0x1e6e2000 0x1a8>;
 				#address-cells = <1>;
-				#size-cells = <0>;
+				#size-cells = <1>;
+				ranges = <0 0x1e6e2000 0x1000>;
 				#clock-cells = <1>;
 				#reset-cells = <1>;
 
-				pinctrl: pinctrl {
-					compatible = "aspeed,ast2500-pinctrl";
-					aspeed,external-nodes = <&gfx &lhc>;
-
+				scu_ic: interrupt-controller@18 {
+					#interrupt-cells = <1>;
+					compatible = "aspeed,ast2500-scu-ic";
+					reg = <0x18 0x4>;
+					interrupts = <21>;
+					interrupt-controller;
 				};
 
-				p2a: p2a-control {
+				p2a: p2a-control@2c {
 					compatible = "aspeed,ast2500-p2a-ctrl";
+					reg = <0x2c 0x4>;
 					status = "disabled";
 				};
+
+				silicon-id@7c {
+					compatible = "aspeed,ast2500-silicon-id", "aspeed,silicon-id";
+					reg = <0x7c 0x4 0x150 0x8>;
+				};
+
+				pinctrl: pinctrl@80 {
+					compatible = "aspeed,ast2500-pinctrl";
+					reg = <0x80 0x18>, <0xa0 0x10>;
+					aspeed,external-nodes = <&gfx>, <&lhc>;
+				};
 			};
 
 			rng: hwrng@1e6e2078 {
@@ -240,16 +262,36 @@
 				quality = <100>;
 			};
 
+			hace: crypto@1e6e3000 {
+				compatible = "aspeed,ast2500-hace";
+				reg = <0x1e6e3000 0x100>;
+				interrupts = <4>;
+				clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
+				resets = <&syscon ASPEED_RESET_HACE>;
+			};
+
 			gfx: display@1e6e6000 {
 				compatible = "aspeed,ast2500-gfx", "syscon";
 				reg = <0x1e6e6000 0x1000>;
 				reg-io-width = <4>;
 				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
 				resets = <&syscon ASPEED_RESET_CRT1>;
+				syscon = <&syscon>;
 				status = "disabled";
 				interrupts = <0x19>;
 			};
 
+			xdma: xdma@1e6e7000 {
+				compatible = "aspeed,ast2500-xdma";
+				reg = <0x1e6e7000 0x100>;
+				clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
+				resets = <&syscon ASPEED_RESET_XDMA>;
+				interrupts-extended = <&vic 6>, <&scu_ic ASPEED_AST2500_SCU_IC_PCIE_RESET_LO_TO_HI>;
+				aspeed,pcie-device = "bmc";
+				aspeed,scu = <&syscon>;
+				status = "disabled";
+			};
+
 			adc: adc@1e6e9000 {
 				compatible = "aspeed,ast2500-adc";
 				reg = <0x1e6e9000 0xb0>;
@@ -322,7 +364,6 @@
 				reg = <0x1e780200 0x0100>;
 				clocks = <&syscon ASPEED_CLK_APB>;
 				interrupt-controller;
-				ngpios = <8>;
 				bus-frequency = <12000000>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_sgpm_default>;
@@ -401,95 +442,101 @@
 				interrupts = <8>;
 				clocks = <&syscon ASPEED_CLK_APB>;
 				no-loopback-test;
-				aspeed,sirq-polarity-sense = <&syscon 0x70 25>;
 				status = "disabled";
 			};
 
 			lpc: lpc@1e789000 {
-				compatible = "aspeed,ast2500-lpc", "simple-mfd";
+				compatible = "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
+				reg-io-width = <4>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0x0 0x1e789000 0x1000>;
 
-				lpc_bmc: lpc-bmc@0 {
-					compatible = "aspeed,ast2500-lpc-bmc", "simple-mfd", "syscon";
-					reg = <0x0 0x80>;
-					reg-io-width = <4>;
-
-					#address-cells = <1>;
-					#size-cells = <1>;
-					ranges = <0x0 0x0 0x80>;
-
-					kcs1: kcs1@0 {
-						compatible = "aspeed,ast2500-kcs-bmc";
-						interrupts = <8>;
-						kcs_chan = <1>;
-						status = "disabled";
-					};
-					kcs2: kcs2@0 {
-						compatible = "aspeed,ast2500-kcs-bmc";
-						interrupts = <8>;
-						kcs_chan = <2>;
-						status = "disabled";
-					};
-					kcs3: kcs3@0 {
-						compatible = "aspeed,ast2500-kcs-bmc";
-						interrupts = <8>;
-						kcs_chan = <3>;
-						status = "disabled";
-					};
+				kcs1: kcs@24 {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				kcs2: kcs@28 {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				kcs3: kcs@2c {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				kcs4: kcs@114 {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lpc_ctrl: lpc-ctrl@80 {
+					compatible = "aspeed,ast2500-lpc-ctrl";
+					reg = <0x80 0x10>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lpc_snoop: lpc-snoop@90 {
+					compatible = "aspeed,ast2500-lpc-snoop";
+					reg = <0x90 0x8>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
 				};
 
-				lpc_host: lpc-host@80 {
-					compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon";
-					reg = <0x80 0x1e0>;
-					reg-io-width = <4>;
-
-					#address-cells = <1>;
-					#size-cells = <1>;
-					ranges = <0x0 0x80 0x1e0>;
-
-					kcs4: kcs4@0 {
-						compatible = "aspeed,ast2500-kcs-bmc";
-						interrupts = <8>;
-						kcs_chan = <4>;
-						status = "disabled";
-					};
-
-					lpc_ctrl: lpc-ctrl@0 {
-						compatible = "aspeed,ast2500-lpc-ctrl";
-						reg = <0x0 0x80>;
-						clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
-						status = "disabled";
-					};
-
-					lpc_snoop: lpc-snoop@0 {
-						compatible = "aspeed,ast2500-lpc-snoop";
-						reg = <0x0 0x80>;
-						interrupts = <8>;
-						status = "disabled";
-					};
-
-					lhc: lhc@20 {
-						compatible = "aspeed,ast2500-lhc";
-						reg = <0x20 0x24 0x48 0x8>;
-					};
-
-					lpc_reset: reset-controller@18 {
-						compatible = "aspeed,ast2500-lpc-reset";
-						reg = <0x18 0x4>;
-						#reset-cells = <1>;
-					};
-
-					ibt: ibt@c0 {
-						compatible = "aspeed,ast2500-ibt-bmc";
-						reg = <0xc0 0x18>;
-						interrupts = <8>;
-						status = "disabled";
-					};
+				lpc_reset: reset-controller@98 {
+					compatible = "aspeed,ast2500-lpc-reset";
+					reg = <0x98 0x4>;
+					#reset-cells = <1>;
 				};
+
+				uart_routing: uart-routing@9c {
+					compatible = "aspeed,ast2500-uart-routing";
+					reg = <0x9c 0x4>;
+					status = "disabled";
+				};
+
+				lhc: lhc@a0 {
+					compatible = "aspeed,ast2500-lhc";
+					reg = <0xa0 0x24 0xc8 0x8>;
+				};
+
+
+				ibt: ibt@140 {
+					compatible = "aspeed,ast2500-ibt-bmc";
+					reg = <0x140 0x18>;
+					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+			};
+
+			peci0: peci-controller@1e78b000 {
+				compatible = "aspeed,ast2500-peci";
+				reg = <0x1e78b000 0x60>;
+				interrupts = <15>;
+				clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+				resets = <&syscon ASPEED_RESET_PECI>;
+				cmd-timeout-ms = <1000>;
+				clock-frequency = <1000000>;
+				status = "disabled";
 			};
 
 			uart2: serial@1e78d000 {
diff --git a/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
index 045ce66ca876..289668f051eb 100644
--- a/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
@@ -117,9 +117,9 @@
 		groups = "FWSPID";
 	};
 
-	pinctrl_fwqspid_default: fwqspid_default {
-		function = "FWQSPID";
-		groups = "FWQSPID";
+	pinctrl_fwqspi_default: fwqspi_default {
+		function = "FWQSPI";
+		groups = "FWQSPI";
 	};
 
 	pinctrl_fwspiwp_default: fwspiwp_default {
@@ -208,12 +208,12 @@
 	};
 
 	pinctrl_hvi3c3_default: hvi3c3_default {
-		function = "HVI3C3";
+		function = "I3C3";
 		groups = "HVI3C3";
 	};
 
 	pinctrl_hvi3c4_default: hvi3c4_default {
-		function = "HVI3C4";
+		function = "I3C4";
 		groups = "HVI3C4";
 	};
 
@@ -297,6 +297,16 @@
 		groups = "I2C9";
 	};
 
+	pinctrl_i3c1_default: i3c1_default {
+		function = "I3C1";
+		groups = "I3C1";
+	};
+
+	pinctrl_i3c2_default: i3c2_default {
+		function = "I3C2";
+		groups = "I3C2";
+	};
+
 	pinctrl_i3c3_default: i3c3_default {
 		function = "I3C3";
 		groups = "I3C3";
@@ -653,12 +663,12 @@
 	};
 
 	pinctrl_qspi1_default: qspi1_default {
-		function = "QSPI1";
+		function = "SPI1";
 		groups = "QSPI1";
 	};
 
 	pinctrl_qspi2_default: qspi2_default {
-		function = "QSPI2";
+		function = "SPI2";
 		groups = "QSPI2";
 	};
 
@@ -862,11 +872,21 @@
 		groups = "SGPM1";
 	};
 
+	pinctrl_sgpm2_default: sgpm2_default {
+		function = "SGPM2";
+		groups = "SGPM2";
+	};
+
 	pinctrl_sgps1_default: sgps1_default {
 		function = "SGPS1";
 		groups = "SGPS1";
 	};
 
+	pinctrl_sgps2_default: sgps2_default {
+		function = "SGPS2";
+		groups = "SGPS2";
+	};
+
 	pinctrl_sioonctrl_default: sioonctrl_default {
 		function = "SIOONCTRL";
 		groups = "SIOONCTRL";
@@ -1112,6 +1132,31 @@
 		groups = "UART9";
 	};
 
+	pinctrl_usb2ah_default: usb2ah_default {
+		function = "USB2AH";
+		groups = "USBA";
+	};
+
+	pinctrl_usb2ad_default: usb2ad_default {
+		function = "USB2AD";
+		groups = "USBA";
+	};
+
+	pinctrl_usb2bh_default: usb2bh_default {
+		function = "USB2BH";
+		groups = "USBB";
+	};
+
+	pinctrl_usb2bd_default: usb2bd_default {
+		function = "USB2BD";
+		groups = "USBB";
+	};
+
+	pinctrl_usb11bhid_default: usb11bhid_default {
+		function = "USB11BHID";
+		groups = "USBB";
+	};
+
 	pinctrl_vb_default: vb_default {
 		function = "VB";
 		groups = "VB";
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi
index 5f6142d99eeb..c4d1faade8be 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi
@@ -2,6 +2,7 @@
 // Copyright 2019 IBM Corp.
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/aspeed-scu-ic.h>
 #include <dt-bindings/clock/ast2600-clock.h>
 
 / {
@@ -35,6 +36,10 @@
 		serial4 = &uart5;
 		serial5 = &vuart1;
 		serial6 = &vuart2;
+		mdio0 = &mdio0;
+		mdio1 = &mdio1;
+		mdio2 = &mdio2;
+		mdio3 = &mdio3;
 	};
 
 
@@ -65,6 +70,13 @@
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
 		clocks = <&syscon ASPEED_CLK_HPLL>;
 		arm,cpu-registers-not-fw-configured;
+		always-on;
+	};
+
+	edac: sdram@1e6e0000 {
+		compatible = "aspeed,ast2600-sdram-edac", "syscon";
+		reg = <0x1e6e0000 0x174>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
 	ahb {
@@ -86,9 +98,13 @@
 			    <0x40466000 0x2000>;
 			};
 
+		ahbc: bus@1e600000 {
+			compatible = "aspeed,ast2600-ahbc", "syscon";
+			reg = <0x1e600000 0x100>;
+		};
+
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-fmc";
@@ -99,25 +115,27 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi1: spi@1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -127,19 +145,20 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi2: spi@1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x50000000 0x10000000 >;
+			reg = <0x1e631000 0xc4>, <0x50000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -149,38 +168,21 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
-				status = "disabled";
-			};
-
-			fsim0: fsi@1e79b000 {
-				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
-				reg = <0x1e79b000 0x94>;
-				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_fsi1_default>;
-				clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
-				status = "disabled";
-			};
-
-			fsim1: fsi@1e79b100 {
-				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
-				reg = <0x1e79b100 0x94>;
-				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_fsi2_default>;
-				clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -193,6 +195,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio1_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio1: mdio@1e650008 {
@@ -203,6 +206,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio2_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio2: mdio@1e650010 {
@@ -213,6 +217,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio3_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio3: mdio@1e650018 {
@@ -223,6 +228,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio4_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mac0: ftgmac@1e660000 {
@@ -265,12 +271,75 @@
 			status = "disabled";
 		};
 
+		ehci0: usb@1e6a1000 {
+			compatible = "aspeed,ast2600-ehci", "generic-ehci";
+			reg = <0x1e6a1000 0x100>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2ah_default>;
+			status = "disabled";
+		};
+
+		ehci1: usb@1e6a3000 {
+			compatible = "aspeed,ast2600-ehci", "generic-ehci";
+			reg = <0x1e6a3000 0x100>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2bh_default>;
+			status = "disabled";
+		};
+
+		uhci: usb@1e6b0000 {
+			compatible = "aspeed,ast2600-uhci", "generic-uhci";
+			reg = <0x1e6b0000 0x100>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			#ports = <2>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
+			status = "disabled";
+			/*
+			 * No default pinmux, it will follow EHCI, use an
+			 * explicit pinmux override if EHCI is not enabled.
+			 */
+		};
+
+		vhub: usb-vhub@1e6a0000 {
+			compatible = "aspeed,ast2600-usb-vhub";
+			reg = <0x1e6a0000 0x350>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			aspeed,vhub-downstream-ports = <7>;
+			aspeed,vhub-generic-endpoints = <21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2ad_default>;
+			status = "disabled";
+		};
+
+		udc: usb@1e6a2000 {
+			compatible = "aspeed,ast2600-udc";
+			reg = <0x1e6a2000 0x300>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2bd_default>;
+			status = "disabled";
+		};
+
 		apb {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
+			hace: crypto@1e6d0000 {
+				compatible = "aspeed,ast2600-hace";
+				reg = <0x1e6d0000 0x200>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
+				resets = <&syscon ASPEED_RESET_HACE>;
+			};
+
 			syscon: syscon@1e6e2000 {
 				compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd";
 				reg = <0x1e6e2000 0x1000>;
@@ -284,10 +353,31 @@
 					compatible = "aspeed,ast2600-pinctrl";
 				};
 
+				silicon-id@14 {
+					compatible = "aspeed,ast2600-silicon-id", "aspeed,silicon-id";
+					reg = <0x14 0x4 0x5b0 0x8>;
+				};
+
 				smp-memram@180 {
 					compatible = "aspeed,ast2600-smpmem";
 					reg = <0x180 0x40>;
 				};
+
+				scu_ic0: interrupt-controller@560 {
+					#interrupt-cells = <1>;
+					compatible = "aspeed,ast2600-scu-ic0";
+					reg = <0x560 0x4>;
+					interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-controller;
+				};
+
+				scu_ic1: interrupt-controller@570 {
+					#interrupt-cells = <1>;
+					compatible = "aspeed,ast2600-scu-ic1";
+					reg = <0x570 0x4>;
+					interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-controller;
+				};
 			};
 
 			rng: hwrng@1e6e2524 {
@@ -297,11 +387,78 @@
 				quality = <100>;
 			};
 
+			gfx: display@1e6e6000 {
+				compatible = "aspeed,ast2600-gfx", "syscon";
+				reg = <0x1e6e6000 0x1000>;
+				reg-io-width = <4>;
+				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
+				resets = <&syscon ASPEED_RESET_GRAPHICS>;
+				syscon = <&syscon>;
+				status = "disabled";
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			xdma: xdma@1e6e7000 {
+				compatible = "aspeed,ast2600-xdma";
+				reg = <0x1e6e7000 0x100>;
+				clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
+				resets = <&syscon ASPEED_RESET_DEV_XDMA>, <&syscon ASPEED_RESET_RC_XDMA>;
+				reset-names = "device", "root-complex";
+				interrupts-extended = <&gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+						      <&scu_ic0 ASPEED_AST2600_SCU_IC0_PCIE_PERST_LO_TO_HI>;
+				aspeed,pcie-device = "bmc";
+				aspeed,scu = <&syscon>;
+				status = "disabled";
+			};
+
+			adc0: adc@1e6e9000 {
+				compatible = "aspeed,ast2600-adc0";
+				reg = <0x1e6e9000 0x100>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				resets = <&syscon ASPEED_RESET_ADC>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				#io-channel-cells = <1>;
+				status = "disabled";
+			};
+
+			adc1: adc@1e6e9100 {
+				compatible = "aspeed,ast2600-adc1";
+				reg = <0x1e6e9100 0x100>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				resets = <&syscon ASPEED_RESET_ADC>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				#io-channel-cells = <1>;
+				status = "disabled";
+			};
+
+			sbc: secure-boot-controller@1e6f2000 {
+				compatible = "aspeed,ast2600-sbc";
+				reg = <0x1e6f2000 0x1000>;
+			};
+
+			acry: crypto@1e6fa000 {
+				compatible = "aspeed,ast2600-acry";
+				reg = <0x1e6fa000 0x400>, <0x1e710000 0x1800>;
+				interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_RSACLK>;
+				aspeed,ahbc = <&ahbc>;
+			};
+
+			video: video@1e700000 {
+				compatible = "aspeed,ast2600-video-engine";
+				reg = <0x1e700000 0x1000>;
+				clocks = <&syscon ASPEED_CLK_GATE_VCLK>,
+					 <&syscon ASPEED_CLK_GATE_ECLK>;
+				clock-names = "vclk", "eclk";
+				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
 			gpio0: gpio@1e780000 {
 				#gpio-cells = <2>;
 				gpio-controller;
 				compatible = "aspeed,ast2600-gpio";
-				reg = <0x1e780000 0x800>;
+				reg = <0x1e780000 0x400>;
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				gpio-ranges = <&pinctrl 0 0 208>;
 				ngpios = <208>;
@@ -310,6 +467,34 @@
 				#interrupt-cells = <2>;
 			};
 
+			sgpiom0: sgpiom@1e780500 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpiom";
+				reg = <0x1e780500 0x100>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				interrupt-controller;
+				bus-frequency = <12000000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sgpm1_default>;
+				status = "disabled";
+			};
+
+			sgpiom1: sgpiom@1e780600 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpiom";
+				reg = <0x1e780600 0x100>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				interrupt-controller;
+				bus-frequency = <12000000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sgpm2_default>;
+				status = "disabled";
+			};
+
 			gpio1: gpio@1e780800 {
 				#gpio-cells = <2>;
 				gpio-controller;
@@ -343,6 +528,7 @@
 						<&gic  GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&syscon ASPEED_CLK_APB1>;
 				clock-names = "PCLK";
+				status = "disabled";
                         };
 
 			uart1: serial@1e783000 {
@@ -385,96 +571,103 @@
 				status = "disabled";
 			};
 
-			wdt4: watchdog@1e7850C0 {
+			wdt4: watchdog@1e7850c0 {
 				compatible = "aspeed,ast2600-wdt";
 				reg = <0x1e7850C0 0x40>;
 				status = "disabled";
 			};
 
+			peci0: peci-controller@1e78b000 {
+				compatible = "aspeed,ast2600-peci";
+				reg = <0x1e78b000 0x100>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
+				resets = <&syscon ASPEED_RESET_PECI>;
+				cmd-timeout-ms = <1000>;
+				clock-frequency = <1000000>;
+				status = "disabled";
+			};
+
 			lpc: lpc@1e789000 {
-				compatible = "aspeed,ast2600-lpc", "simple-mfd";
+				compatible = "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
+				reg-io-width = <4>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0x0 0x1e789000 0x1000>;
 
-				lpc_bmc: lpc-bmc@0 {
-					compatible = "aspeed,ast2600-lpc-bmc", "simple-mfd", "syscon";
-					reg = <0x0 0x80>;
-					reg-io-width = <4>;
-
-					#address-cells = <1>;
-					#size-cells = <1>;
-					ranges = <0x0 0x0 0x80>;
-
-					kcs1: kcs1@0 {
-						compatible = "aspeed,ast2600-kcs-bmc";
-						interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
-						kcs_chan = <1>;
-						status = "disabled";
-					};
-					kcs2: kcs2@0 {
-						compatible = "aspeed,ast2600-kcs-bmc";
-						interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
-						kcs_chan = <2>;
-						status = "disabled";
-					};
-					kcs3: kcs3@0 {
-						compatible = "aspeed,ast2600-kcs-bmc";
-						interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
-						kcs_chan = <3>;
-						status = "disabled";
-					};
+				kcs1: kcs@24 {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
+					interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					kcs_chan = <1>;
+					status = "disabled";
+				};
+
+				kcs2: kcs@28 {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
+					interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				kcs3: kcs@2c {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
+					interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				kcs4: kcs@114 {
+					compatible = "aspeed,ast2500-kcs-bmc-v2";
+					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
+					interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lpc_ctrl: lpc-ctrl@80 {
+					compatible = "aspeed,ast2600-lpc-ctrl";
+					reg = <0x80 0x80>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lpc_snoop: lpc-snoop@80 {
+					compatible = "aspeed,ast2600-lpc-snoop";
+					reg = <0x80 0x80>;
+					interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
+				};
+
+				lhc: lhc@a0 {
+					compatible = "aspeed,ast2600-lhc";
+					reg = <0xa0 0x24 0xc8 0x8>;
+				};
+
+				lpc_reset: reset-controller@98 {
+					compatible = "aspeed,ast2600-lpc-reset";
+					reg = <0x98 0x4>;
+					#reset-cells = <1>;
+				};
+
+				uart_routing: uart-routing@98 {
+					compatible = "aspeed,ast2600-uart-routing";
+					reg = <0x98 0x8>;
+					status = "disabled";
 				};
 
-				lpc_host: lpc-host@80 {
-					compatible = "aspeed,ast2600-lpc-host", "simple-mfd", "syscon";
-					reg = <0x80 0x1e0>;
-					reg-io-width = <4>;
-
-					#address-cells = <1>;
-					#size-cells = <1>;
-					ranges = <0x0 0x80 0x1e0>;
-
-					kcs4: kcs4@0 {
-						compatible = "aspeed,ast2600-kcs-bmc";
-						interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
-						kcs_chan = <4>;
-						status = "disabled";
-					};
-
-					lpc_ctrl: lpc-ctrl@0 {
-						compatible = "aspeed,ast2600-lpc-ctrl";
-						reg = <0x0 0x80>;
-						clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
-						status = "disabled";
-					};
-
-					lpc_snoop: lpc-snoop@0 {
-						compatible = "aspeed,ast2600-lpc-snoop";
-						reg = <0x0 0x80>;
-						interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
-						status = "disabled";
-					};
-
-					lhc: lhc@20 {
-						compatible = "aspeed,ast2600-lhc";
-						reg = <0x20 0x24 0x48 0x8>;
-					};
-
-					lpc_reset: reset-controller@18 {
-						compatible = "aspeed,ast2600-lpc-reset";
-						reg = <0x18 0x4>;
-						#reset-cells = <1>;
-					};
-
-					ibt: ibt@c0 {
-						compatible = "aspeed,ast2600-ibt-bmc";
-						reg = <0xc0 0x18>;
-						interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
-						status = "disabled";
-					};
+				ibt: ibt@140 {
+					compatible = "aspeed,ast2600-ibt-bmc";
+					reg = <0x140 0x18>;
+					interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
+					status = "disabled";
 				};
 			};
 
@@ -536,6 +729,16 @@
 				status = "disabled";
 			};
 
+			vuart3: serial@1e787800 {
+				compatible = "aspeed,ast2500-vuart";
+				reg = <0x1e787800 0x40>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				no-loopback-test;
+				status = "disabled";
+			};
+
 			vuart2: serial@1e788000 {
 				compatible = "aspeed,ast2500-vuart";
 				reg = <0x1e788000 0x40>;
@@ -546,6 +749,16 @@
 				status = "disabled";
 			};
 
+			vuart4: serial@1e788800 {
+				compatible = "aspeed,ast2500-vuart";
+				reg = <0x1e788800 0x40>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				no-loopback-test;
+				status = "disabled";
+			};
+
 			uart2: serial@1e78d000 {
 				compatible = "ns16550a";
 				reg = <0x1e78d000 0x20>;
@@ -588,6 +801,62 @@
 				status = "disabled";
 			};
 
+			uart6: serial@1e790000 {
+				compatible = "ns16550a";
+				reg = <0x1e790000 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART6CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart6_default>;
+
+				status = "disabled";
+			};
+
+			uart7: serial@1e790100 {
+				compatible = "ns16550a";
+				reg = <0x1e790100 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART7CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart7_default>;
+
+				status = "disabled";
+			};
+
+			uart8: serial@1e790200 {
+				compatible = "ns16550a";
+				reg = <0x1e790200 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART8CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart8_default>;
+
+				status = "disabled";
+			};
+
+			uart9: serial@1e790300 {
+				compatible = "ns16550a";
+				reg = <0x1e790300 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART9CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart9_default>;
+
+				status = "disabled";
+			};
+
 			i2c: bus@1e78a000 {
 				compatible = "simple-bus";
 				#address-cells = <1>;
@@ -595,6 +864,34 @@
 				ranges = <0 0x1e78a000 0x1000>;
 			};
 
+			fsim0: fsi@1e79b000 {
+				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
+				reg = <0x1e79b000 0x94>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_fsi1_default>;
+				clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+				status = "disabled";
+			};
+
+			fsim1: fsi@1e79b100 {
+				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
+				reg = <0x1e79b100 0x94>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_fsi2_default>;
+				clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+				status = "disabled";
+			};
+
+			udma: dma-controller@1e79e000 {
+				compatible = "aspeed,ast2600-udma";
+				reg = <0x1e79e000 0x1000>;
+				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+				dma-channels = <28>;
+				#dma-cells = <1>;
+				status = "disabled";
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge40.dts b/arch/arm/boot/dts/aspeed/ast2400-facebook-netbmc-common.dtsi
index aaa77a597d1a..4e5e786e18b7 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge40.dts
+++ b/arch/arm/boot/dts/aspeed/ast2400-facebook-netbmc-common.dtsi
@@ -1,13 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0+
-// Copyright (c) 2018 Facebook Inc.
+// Copyright (c) 2020 Facebook Inc.
 /dts-v1/;
 
 #include "aspeed-g4.dtsi"
 
 / {
-	model = "Facebook Wedge 40 BMC";
-	compatible = "facebook,wedge40-bmc", "aspeed,ast2400";
-
 	aliases {
 		/*
 		 * Override the default uart aliases to avoid breaking
@@ -19,11 +16,6 @@
 		serial3 = &uart4;
 	};
 
-	chosen {
-		stdout-path = &uart3;
-		bootargs = "console=ttyS2,9600n8 root=/dev/ram rw";
-	};
-
 	memory@40000000 {
 		reg = <0x40000000 0x20000000>;
 	};
@@ -34,16 +26,12 @@
 	aspeed,reset-type = "system";
 };
 
-&wdt2 {
-	status = "disabled";
-};
-
 &fmc {
 	status = "okay";
 	flash@0 {
 		status = "okay";
 		m25p,fast-read;
-		label = "fmc0";
+		label = "spi0.0";
 #include "facebook-bmc-flash-layout.dtsi"
 	};
 };
@@ -66,7 +54,8 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_txd4_default
-		     &pinctrl_rxd4_default>;
+		     &pinctrl_rxd4_default
+		     &pinctrl_ndts4_default>;
 };
 
 &uart5 {
@@ -75,7 +64,6 @@
 
 &mac1 {
 	status = "okay";
-	no-hw-checksum;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
 };
@@ -116,14 +104,6 @@
 	status = "okay";
 };
 
-&i2c9 {
-	status = "okay";
-};
-
-&i2c10 {
-	status = "okay";
-};
-
 &i2c11 {
 	status = "okay";
 };
@@ -132,10 +112,10 @@
 	status = "okay";
 };
 
-&i2c13 {
+&vhub {
 	status = "okay";
 };
 
-&vhub {
+&adc {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/ast2500-facebook-netbmc-common.dtsi b/arch/arm/boot/dts/aspeed/ast2500-facebook-netbmc-common.dtsi
index 7a395ba56512..7f1ae3f4df9d 100644
--- a/arch/arm/boot/dts/ast2500-facebook-netbmc-common.dtsi
+++ b/arch/arm/boot/dts/aspeed/ast2500-facebook-netbmc-common.dtsi
@@ -4,6 +4,10 @@
 #include "aspeed-g5.dtsi"
 
 / {
+	aliases {
+		spi0 = &fmc;
+	};
+
 	memory@80000000 {
 		reg = <0x80000000 0x40000000>;
 	};
@@ -47,31 +51,17 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "spi0.0";
-
-#include "facebook-bmc-flash-layout.dtsi"
 	};
 
 	fmc_flash1: flash@1 {
 		status = "okay";
 		m25p,fast-read;
 		label = "spi0.1";
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			flash1@0 {
-				reg = <0x0 0x2000000>;
-				label = "flash1";
-			};
-		};
 	};
 };
 
 &mac1 {
 	status = "okay";
-	no-hw-checksum;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
 };
diff --git a/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi b/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi
new file mode 100644
index 000000000000..31590d3186a2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	aliases {
+		mmc0 = &emmc;
+		spi1 = &spi1;
+		spi2 = &spi_gpio;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,9600n8 root=/dev/ram rw vmalloc=640M";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	/*
+	 * GPIO-based SPI Master is required to access SPI TPM, because
+	 * full-duplex SPI transactions are not supported by ASPEED SPI
+	 * Controllers.
+	 */
+	spi_gpio: spi {
+		status = "okay";
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+
+		tpmdev@0 {
+			compatible = "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "spi0.0";
+
+#include "facebook-bmc-flash-layout-128.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "spi0.1";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash1@0 {
+				reg = <0x0 0x8000000>;
+				label = "flash1";
+			};
+		};
+	};
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+
+	non-removable;
+	max-frequency = <25000000>;
+	bus-width = <4>;
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128.dtsi b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128.dtsi
new file mode 100644
index 000000000000..7f3652dea550
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128.dtsi
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+partitions {
+	compatible = "fixed-partitions";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/*
+	 * u-boot partition: 896KB.
+	 */
+	u-boot@0 {
+		reg = <0x0 0xe0000>;
+		label = "u-boot";
+	};
+
+	/*
+	 * u-boot environment variables: 64KB.
+	 */
+	u-boot-env@e0000 {
+		reg = <0xe0000 0x10000>;
+		label = "env";
+	};
+
+	/*
+	 * image metadata partition (64KB), used by Facebook internal
+	 * tools.
+	 */
+	image-meta@f0000 {
+		reg = <0xf0000 0x10000>;
+		label = "meta";
+	};
+
+	/*
+	 * FIT image: 119 MB.
+	 */
+	fit@100000 {
+		reg = <0x100000 0x7700000>;
+		label = "fit";
+	};
+
+	/*
+	 * "data0" partition (8MB) is used by Facebook BMC platforms as
+	 * persistent data store.
+	 */
+	data0@7800000 {
+		reg = <0x7800000 0x800000>;
+		label = "data0";
+	};
+
+	/*
+	 * Although the master partition can be created by enabling
+	 * MTD_PARTITIONED_MASTER option, below "flash0" partition is
+	 * explicitly created to avoid breaking legacy applications.
+	 */
+	flash0@0 {
+		reg = <0x0 0x8000000>;
+		label = "flash0";
+	};
+};
diff --git a/arch/arm/boot/dts/facebook-bmc-flash-layout.dtsi b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout.dtsi
index 87bb8b576250..87bb8b576250 100644
--- a/arch/arm/boot/dts/facebook-bmc-flash-layout.dtsi
+++ b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout.dtsi
diff --git a/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
new file mode 100644
index 000000000000..cc466910bb52
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
@@ -0,0 +1,380 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 IBM Corp.
+
+&fsim0 {
+	status = "okay";
+
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+
+	cfam@0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OMI01 */
+			};
+
+			cfam0_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OMI23 */
+			};
+
+			cfam0_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam0_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam0_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam0_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam0_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam0_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi2: spi@40 {
+				reg = <0x40>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi3: spi@60 {
+				reg = <0x60>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ0: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub0: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OMI45 */
+			};
+
+			cfam1_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OMI67 */
+			};
+
+			cfam1_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam1_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam1_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam1_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam1_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam1_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi2: spi@40 {
+				reg = <0x40>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi3: spi@60 {
+				reg = <0x60>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ1: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub1: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ0 {
+	reg = <1>;
+};
+
+&fsi_occ1 {
+	reg = <2>;
+};
+
+/ {
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi
new file mode 100644
index 000000000000..57494c744b5d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi
@@ -0,0 +1,1305 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 IBM Corp.
+
+#include "ibm-power10-dual.dtsi"
+
+&cfam0_i2c0 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom100: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo100: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c1 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom101: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo101: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c10 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom110: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo110: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c11 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom111: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo111: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c12 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom112: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo112: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c13 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom113: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo113: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c14 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom114: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo114: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c15 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom115: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo115: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c2 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom202: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo202: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c3 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom203: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo203: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c10 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom210: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo210: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c11 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom211: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo211: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c14 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom214: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo214: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c15 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom215: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo215: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c16 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom216: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo216: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c17 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom217: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo217: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@2,0 {
+		reg = <2 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <2>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom300: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo300: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom301: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo301: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom310: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo310: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom311: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo311: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom312: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo312: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom313: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo313: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom314: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo314: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom315: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo315: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi2: spi@40 {
+				reg = <0x40>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi3: spi@60 {
+				reg = <0x60>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ2: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub2: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@3,0 {
+		reg = <3 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <3>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom402: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo402: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom403: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo403: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom410: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo410: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom411: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo411: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom414: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo414: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom415: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo415: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom416: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo416: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom417: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo417: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi2: spi@40 {
+				reg = <0x40>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi3: spi@60 {
+				reg = <0x60>;
+				compatible =  "ibm,fsi2spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ3: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub3: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ2 {
+	reg = <3>;
+};
+
+&fsi_occ3 {
+	reg = <4>;
+};
+
+/ {
+	aliases {
+		i2c300 = &cfam2_i2c0;
+		i2c301 = &cfam2_i2c1;
+		i2c310 = &cfam2_i2c10;
+		i2c311 = &cfam2_i2c11;
+		i2c312 = &cfam2_i2c12;
+		i2c313 = &cfam2_i2c13;
+		i2c314 = &cfam2_i2c14;
+		i2c315 = &cfam2_i2c15;
+		i2c402 = &cfam3_i2c2;
+		i2c403 = &cfam3_i2c3;
+		i2c410 = &cfam3_i2c10;
+		i2c411 = &cfam3_i2c11;
+		i2c414 = &cfam3_i2c14;
+		i2c415 = &cfam3_i2c15;
+		i2c416 = &cfam3_i2c16;
+		i2c417 = &cfam3_i2c17;
+
+		sbefifo100 = &sbefifo100;
+		sbefifo101 = &sbefifo101;
+		sbefifo110 = &sbefifo110;
+		sbefifo111 = &sbefifo111;
+		sbefifo112 = &sbefifo112;
+		sbefifo113 = &sbefifo113;
+		sbefifo114 = &sbefifo114;
+		sbefifo115 = &sbefifo115;
+		sbefifo202 = &sbefifo202;
+		sbefifo203 = &sbefifo203;
+		sbefifo210 = &sbefifo210;
+		sbefifo211 = &sbefifo211;
+		sbefifo214 = &sbefifo214;
+		sbefifo215 = &sbefifo215;
+		sbefifo216 = &sbefifo216;
+		sbefifo217 = &sbefifo217;
+		sbefifo300 = &sbefifo300;
+		sbefifo301 = &sbefifo301;
+		sbefifo310 = &sbefifo310;
+		sbefifo311 = &sbefifo311;
+		sbefifo312 = &sbefifo312;
+		sbefifo313 = &sbefifo313;
+		sbefifo314 = &sbefifo314;
+		sbefifo315 = &sbefifo315;
+		sbefifo402 = &sbefifo402;
+		sbefifo403 = &sbefifo403;
+		sbefifo410 = &sbefifo410;
+		sbefifo411 = &sbefifo411;
+		sbefifo414 = &sbefifo414;
+		sbefifo415 = &sbefifo415;
+		sbefifo416 = &sbefifo416;
+		sbefifo417 = &sbefifo417;
+
+		scom100 = &scom100;
+		scom101 = &scom101;
+		scom110 = &scom110;
+		scom111 = &scom111;
+		scom112 = &scom112;
+		scom113 = &scom113;
+		scom114 = &scom114;
+		scom115 = &scom115;
+		scom202 = &scom202;
+		scom203 = &scom203;
+		scom210 = &scom210;
+		scom211 = &scom211;
+		scom214 = &scom214;
+		scom215 = &scom215;
+		scom216 = &scom216;
+		scom217 = &scom217;
+		scom300 = &scom300;
+		scom301 = &scom301;
+		scom310 = &scom310;
+		scom311 = &scom311;
+		scom312 = &scom312;
+		scom313 = &scom313;
+		scom314 = &scom314;
+		scom315 = &scom315;
+		scom402 = &scom402;
+		scom403 = &scom403;
+		scom410 = &scom410;
+		scom411 = &scom411;
+		scom414 = &scom414;
+		scom415 = &scom415;
+		scom416 = &scom416;
+		scom417 = &scom417;
+
+		spi30 = &cfam2_spi0;
+		spi31 = &cfam2_spi1;
+		spi32 = &cfam2_spi2;
+		spi33 = &cfam2_spi3;
+		spi40 = &cfam3_spi0;
+		spi41 = &cfam3_spi1;
+		spi42 = &cfam3_spi2;
+		spi43 = &cfam3_spi3;
+	};
+};
diff --git a/arch/arm/boot/dts/ibm-power9-dual.dtsi b/arch/arm/boot/dts/aspeed/ibm-power9-dual.dtsi
index 2abc42eda7b0..a0fa65b44b0f 100644
--- a/arch/arm/boot/dts/ibm-power9-dual.dtsi
+++ b/arch/arm/boot/dts/aspeed/ibm-power9-dual.dtsi
@@ -86,7 +86,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			fsi_occ0: occ {
+			fsi_occ0: occ@1 {
 				compatible = "ibm,p9-occ";
 			};
 		};
@@ -187,7 +187,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			fsi_occ1: occ {
+			fsi_occ1: occ@2 {
 				compatible = "ibm,p9-occ";
 			};
 		};
diff --git a/arch/arm/boot/dts/openbmc-flash-layout-128.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-128.dtsi
index 05101a38c5bd..05101a38c5bd 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout-128.dtsi
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-128.dtsi
diff --git a/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64-alt.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64-alt.dtsi
new file mode 100644
index 000000000000..650525867561
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64-alt.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Bytedance.
+ */
+
+partitions {
+	compatible = "fixed-partitions";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	u-boot@0 {
+		reg = <0x0 0xe0000>; // 896KB
+		label = "alt-u-boot";
+	};
+
+	u-boot-env@e0000 {
+		reg = <0xe0000 0x20000>; // 128KB
+		label = "alt-u-boot-env";
+	};
+
+	kernel@100000 {
+		reg = <0x100000 0x900000>; // 9MB
+		label = "alt-kernel";
+	};
+
+	rofs@a00000 {
+		reg = <0xa00000 0x2000000>; // 32MB
+		label = "alt-rofs";
+	};
+
+	rwfs@6000000 {
+		reg = <0x2a00000 0x1600000>; // 22MB
+		label = "alt-rwfs";
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64.dtsi
new file mode 100644
index 000000000000..7af41361c480
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Bytedance.
+ */
+
+partitions {
+	compatible = "fixed-partitions";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	u-boot@0 {
+		reg = <0x0 0xe0000>; // 896KB
+		label = "u-boot";
+	};
+
+	u-boot-env@e0000 {
+		reg = <0xe0000 0x20000>; // 128KB
+		label = "u-boot-env";
+	};
+
+	kernel@100000 {
+		reg = <0x100000 0x900000>; // 9MB
+		label = "kernel";
+	};
+
+	rofs@a00000 {
+		reg = <0xa00000 0x2000000>; // 32MB
+		label = "rofs";
+	};
+
+	rwfs@2a00000 {
+		reg = <0x2a00000 0x1600000>; // 22MB
+		label = "rwfs";
+	};
+};
diff --git a/arch/arm/boot/dts/openbmc-flash-layout.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout.dtsi
index 6c26524e93e1..b47e14063c38 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout.dtsi
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout.dtsi
@@ -20,7 +20,7 @@ partitions {
 		label = "kernel";
 	};
 
-	rofs@c0000 {
+	rofs@4c0000 {
 		reg = <0x4c0000 0x1740000>;
 		label = "rofs";
 	};
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
deleted file mode 100644
index 90996eaf73b2..000000000000
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ /dev/null
@@ -1,181 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * at91-kizbox.dts - Device Tree file for Overkiz Kizbox board
- *
- * Copyright (C) 2012-2014 Boris BREZILLON <b.brezillon@overkiz.com>
- *               2014-2015 Gaël PORTAY <g.portay@overkiz.com>
- */
-/dts-v1/;
-#include "at91sam9g20.dtsi"
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
-	model = "Overkiz Kizbox";
-	compatible = "overkiz,kizbox", "atmel,at91sam9g20", "atmel,at91sam9";
-
-	chosen {
-		bootargs = "ubi.mtd=ubi";
-		stdout-path = &dbgu;
-	};
-
-	memory {
-		reg = <0x20000000 0x2000000>;
-	};
-
-	clocks {
-		main_xtal {
-			clock-frequency = <18432000>;
-		};
-	};
-
-	ahb {
-		apb {
-			tcb0: timer@fffa0000 {
-				timer@0 {
-					compatible = "atmel,tcb-timer";
-					reg = <0>, <1>;
-				};
-
-				timer@2 {
-					compatible = "atmel,tcb-timer";
-					reg = <2>;
-				};
-			};
-
-			macb0: ethernet@fffc4000 {
-				phy-mode = "mii";
-				pinctrl-0 = <&pinctrl_macb_rmii
-				             &pinctrl_macb_rmii_mii_alt>;
-				status = "okay";
-			};
-
-			usart3: serial@fffd0000 {
-				status = "okay";
-			};
-
-			dbgu: serial@fffff200 {
-				status = "okay";
-			};
-
-			watchdog@fffffd40 {
-				timeout-sec = <15>;
-				atmel,max-heartbeat-sec = <16>;
-				atmel,min-heartbeat-sec = <0>;
-				status = "okay";
-			};
-		};
-
-		usb0: ohci@500000 {
-			num-ports = <1>;
-			status = "okay";
-		};
-
-		ebi: ebi@10000000 {
-			status = "okay";
-
-			nand_controller: nand-controller {
-				status = "okay";
-				pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
-				pinctrl-names = "default";
-
-				nand@3 {
-					reg = <0x3 0x0 0x800000>;
-					rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
-					nand-bus-width = <8>;
-					nand-ecc-mode = "soft";
-					nand-on-flash-bbt;
-					label = "atmel_nand";
-
-					partitions {
-						compatible = "fixed-partitions";
-						#address-cells = <1>;
-						#size-cells = <1>;
-
-						bootstrap@0 {
-							label = "bootstrap";
-							reg = <0x0 0x20000>;
-						};
-
-						ubi@20000 {
-							label = "ubi";
-							reg = <0x20000 0x7fe0000>;
-						};
-					};
-				};
-			};
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reset {
-			label = "PB_RST";
-			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
-			linux,code = <0x100>;
-			wakeup-source;
-		};
-
-		user {
-			label = "PB_USER";
-			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
-			linux,code = <0x101>;
-			wakeup-source;
-		};
-	};
-
-	i2c-gpio-0 {
-		status = "okay";
-
-		rtc: pcf8563@51 {
-			compatible = "nxp,pcf8563";
-			reg = <0x51>;
-		};
-	};
-
-	pwm_leds {
-		compatible = "pwm-leds";
-
-		network_green {
-			label = "pwm:green:network";
-			pwms = <&tcb_pwm 2 10000000 PWM_POLARITY_INVERTED>;
-			max-brightness = <255>;
-			linux,default-trigger = "default-on";
-		};
-
-		network_red {
-			label = "pwm:red:network";
-			pwms = <&tcb_pwm 4 10000000 PWM_POLARITY_INVERTED>;
-			max-brightness = <255>;
-			linux,default-trigger = "default-on";
-		};
-
-		user_green {
-			label = "pwm:green:user";
-			pwms = <&tcb_pwm 0 10000000 PWM_POLARITY_INVERTED>;
-			max-brightness = <255>;
-			linux,default-trigger = "default-on";
-		};
-
-		user_red {
-			label = "pwm:red:user";
-			pwms = <&tcb_pwm 1 10000000 PWM_POLARITY_INVERTED>;
-			max-brightness = <255>;
-			linux,default-trigger = "default-on";
-		};
-	};
-
-	tcb_pwm: pwm {
-		compatible = "atmel,tcb-pwm";
-		#pwm-cells = <3>;
-		tc-block = <1>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tcb1_tioa0
-			     &pinctrl_tcb1_tioa1
-			     &pinctrl_tcb1_tioa2
-			     &pinctrl_tcb1_tiob0>;
-	};
-};
diff --git a/arch/arm/boot/dts/at91-kizboxmini.dts b/arch/arm/boot/dts/at91-kizboxmini.dts
deleted file mode 100644
index cb22f5fb055f..000000000000
--- a/arch/arm/boot/dts/at91-kizboxmini.dts
+++ /dev/null
@@ -1,171 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
- *
- * Copyright (C) 2014 Gaël PORTAY <g.portay@overkiz.com>
- */
-/dts-v1/;
-#include "at91sam9g25.dtsi"
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
-	model = "Overkiz Kizbox mini";
-	compatible = "overkiz,kizboxmini", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9";
-
-	chosen {
-		bootargs = "ubi.mtd=ubi";
-		stdout-path = &dbgu;
-	};
-
-	memory {
-		reg = <0x20000000 0x8000000>;
-	};
-
-	clocks {
-		slow_xtal {
-			clock-frequency = <32768>;
-		};
-
-		main_xtal {
-			clock-frequency = <12000000>;
-		};
-	};
-
-	ahb {
-		nand0: nand@40000000 {
-			nand-bus-width = <8>;
-			nand-ecc-mode = "hw";
-			atmel,has-pmecc;
-			atmel,pmecc-cap = <4>;
-			atmel,pmecc-sector-size = <512>;
-			nand-on-flash-bbt;
-			status = "okay";
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		prog {
-			label = "PB_PROG";
-			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
-			linux,code = <0x102>;
-			wakeup-source;
-		};
-
-		reset {
-			label = "PB_RST";
-			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
-			linux,code = <0x100>;
-			wakeup-source;
-		};
-	};
-
-	pwm_leds {
-		compatible = "pwm-leds";
-
-		green {
-			label = "pwm:green:user";
-			pwms = <&pwm0 0 10000000 0>;
-			max-brightness = <255>;
-			linux,default-trigger = "default-on";
-		};
-
-		red {
-			label = "pwm:red:user";
-			pwms = <&pwm0 1 10000000 0>;
-			max-brightness = <255>;
-			linux,default-trigger = "default-on";
-		};
-	};
-};
-
-&dbgu {
-	status = "okay";
-};
-
-&ebi {
-	pinctrl-0 = <&pinctrl_ebi_addr_nand
-		     &pinctrl_ebi_data_0_7>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	nand-controller {
-		pinctrl-0 = <&pinctrl_nand_oe_we
-			     &pinctrl_nand_cs
-			     &pinctrl_nand_rb>;
-		pinctrl-names = "default";
-		status = "okay";
-
-		nand@3 {
-			reg = <0x3 0x0 0x800000>;
-			rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
-			cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
-			nand-bus-width = <8>;
-			nand-ecc-mode = "hw";
-			nand-ecc-strength = <4>;
-			nand-ecc-step-size = <512>;
-			nand-on-flash-bbt;
-			label = "atmel_nand";
-
-			partitions {
-				compatible = "fixed-partitions";
-				#address-cells = <1>;
-				#size-cells = <1>;
-
-				bootstrap@0 {
-					label = "bootstrap";
-					reg = <0x0 0x20000>;
-				};
-
-				ubi@20000 {
-					label = "ubi";
-					reg = <0x20000 0x7fe0000>;
-				};
-			};
-		};
-	};
-};
-
-&macb0 {
-	phy-mode = "rmii";
-	status = "okay";
-};
-
-&pwm0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm0_pwm0_1
-		     &pinctrl_pwm0_pwm1_1>;
-	status = "okay";
-};
-
-&tcb0 {
-	timer@0 {
-		compatible = "atmel,tcb-timer";
-		reg = <0>;
-	};
-
-	timer@1 {
-		compatible = "atmel,tcb-timer";
-		reg = <1>;
-	};
-};
-
-&usart0 {
-	status = "okay";
-};
-
-&usb0 {
-	num-ports = <1>;
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
-
-&watchdog {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/atlas6-evb.dts b/arch/arm/boot/dts/atlas6-evb.dts
deleted file mode 100644
index 89e430392f26..000000000000
--- a/arch/arm/boot/dts/atlas6-evb.dts
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DTS file for CSR SiRFatlas6 Evaluation Board
- *
- * Copyright (c) 2012 Cambridge Silicon Radio Limited, a CSR plc group company.
- */
-
-/dts-v1/;
-
-/include/ "atlas6.dtsi"
-
-/ {
-	model = "CSR SiRFatlas6 Evaluation Board";
-	compatible = "sirf,atlas6-cb", "sirf,atlas6";
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	axi {
-		peri-iobg {
-			uart@b0060000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&uart1_pins_a>;
-			};
-			spi@b00d0000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi0_pins_a>;
-				spi@0 {
-					compatible = "spidev";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-			spi@b0170000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi1_pins_a>;
-			};
-			i2c0: i2c@b00e0000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				lcd@40 {
-					compatible = "sirf,lcd";
-					reg = <0x40>;
-				};
-			};
-
-		};
-		disp-iobg {
-			lcd@90010000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcd_24pins_a>;
-			};
-		};
-	};
-	display: display@0 {
-	    panels {
-		panel0: panel@0 {
-			panel-name = "Innolux TFT";
-			hactive = <800>;
-			vactive = <480>;
-			left_margin = <20>;
-			right_margin = <234>;
-			upper_margin = <3>;
-			lower_margin = <41>;
-			hsync_len = <3>;
-			vsync_len = <2>;
-			pixclock = <33264000>;
-			sync = <3>;
-			timing = <0x88>;
-			};
-	    };
-	};
-};
diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi
deleted file mode 100644
index 8ac5d1524a43..000000000000
--- a/arch/arm/boot/dts/atlas6.dtsi
+++ /dev/null
@@ -1,800 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DTS file for CSR SiRFatlas6 SoC
- *
- * Copyright (c) 2012 Cambridge Silicon Radio Limited, a CSR plc group company.
- */
-
-/ {
-	compatible = "sirf,atlas6";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&intc>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			reg = <0x0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <32768>;
-			i-cache-size = <32768>;
-			/* from bootloader */
-			timebase-frequency = <0>;
-			bus-frequency = <0>;
-			clock-frequency = <0>;
-			clocks = <&clks 12>;
-			operating-points = <
-				/* kHz    uV */
-				200000  1025000
-				400000  1025000
-				600000  1050000
-				800000  1100000
-			>;
-			clock-latency = <150000>;
-		};
-	};
-
-	arm-pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts = <29>;
-	};
-
-	axi {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x40000000 0x40000000 0x80000000>;
-
-		intc: interrupt-controller@80020000 {
-			#interrupt-cells = <1>;
-			interrupt-controller;
-			compatible = "sirf,prima2-intc";
-			reg = <0x80020000 0x1000>;
-		};
-
-		sys-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x88000000 0x88000000 0x40000>;
-
-			clks: clock-controller@88000000 {
-				compatible = "sirf,atlas6-clkc";
-				reg = <0x88000000 0x1000>;
-				interrupts = <3>;
-				#clock-cells = <1>;
-			};
-
-			rstc: reset-controller@88010000 {
-				compatible = "sirf,prima2-rstc";
-				reg = <0x88010000 0x1000>;
-				#reset-cells = <1>;
-			};
-
-			rsc-controller@88020000 {
-				compatible = "sirf,prima2-rsc";
-				reg = <0x88020000 0x1000>;
-			};
-
-			cphifbg@88030000 {
-				compatible = "sirf,prima2-cphifbg";
-				reg = <0x88030000 0x1000>;
-				clocks = <&clks 42>;
-			};
-		};
-
-		mem-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x90000000 0x90000000 0x10000>;
-
-			memory-controller@90000000 {
-				compatible = "sirf,prima2-memc";
-				reg = <0x90000000 0x2000>;
-				interrupts = <27>;
-				clocks = <&clks 5>;
-			};
-
-			memc-monitor {
-				compatible = "sirf,prima2-memcmon";
-				reg = <0x90002000 0x200>;
-				interrupts = <4>;
-				clocks = <&clks 32>;
-			};
-		};
-
-		disp-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x90010000 0x90010000 0x30000>;
-
-			lcd@90010000 {
-				compatible = "sirf,prima2-lcd";
-				reg = <0x90010000 0x20000>;
-				interrupts = <30>;
-				clocks = <&clks 34>;
-				display=<&display>;
-				/* later transfer to pwm */
-				bl-gpio = <&gpio 7 0>;
-				default-panel = <&panel0>;
-			};
-
-			vpp@90020000 {
-				compatible = "sirf,prima2-vpp";
-				reg = <0x90020000 0x10000>;
-				interrupts = <31>;
-				clocks = <&clks 35>;
-				resets = <&rstc 6>;
-			};
-		};
-
-		graphics-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x98000000 0x98000000 0x8000000>;
-
-			graphics@98000000 {
-				compatible = "powervr,sgx510";
-				reg = <0x98000000 0x8000000>;
-				interrupts = <6>;
-				clocks = <&clks 32>;
-			};
-		};
-
-		graphics2d-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xa0000000 0xa0000000 0x8000000>;
-
-			ble@a0000000 {
-				compatible = "sirf,atlas6-ble";
-				reg = <0xa0000000 0x2000>;
-				interrupts = <5>;
-				clocks = <&clks 33>;
-			};
-		};
-
-		dsp-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xa8000000 0xa8000000 0x2000000>;
-
-			dspif@a8000000 {
-				compatible = "sirf,prima2-dspif";
-				reg = <0xa8000000 0x10000>;
-				interrupts = <9>;
-				resets = <&rstc 1>;
-			};
-
-			gps@a8010000 {
-				compatible = "sirf,prima2-gps";
-				reg = <0xa8010000 0x10000>;
-				interrupts = <7>;
-				clocks = <&clks 9>;
-				resets = <&rstc 2>;
-			};
-
-			dsp@a9000000 {
-				compatible = "sirf,prima2-dsp";
-				reg = <0xa9000000 0x1000000>;
-				interrupts = <8>;
-				clocks = <&clks 8>;
-				resets = <&rstc 0>;
-			};
-		};
-
-		peri-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xb0000000 0xb0000000 0x180000>,
-			       <0x56000000 0x56000000 0x1b00000>;
-
-			timer@b0020000 {
-				compatible = "sirf,prima2-tick";
-				reg = <0xb0020000 0x1000>;
-				interrupts = <0>;
-				clocks = <&clks 11>;
-			};
-
-			nand@b0030000 {
-				compatible = "sirf,prima2-nand";
-				reg = <0xb0030000 0x10000>;
-				interrupts = <41>;
-				clocks = <&clks 26>;
-			};
-
-			audio@b0040000 {
-				compatible = "sirf,prima2-audio";
-				reg = <0xb0040000 0x10000>;
-				interrupts = <35>;
-				clocks = <&clks 27>;
-			};
-
-			uart0: uart@b0050000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-uart";
-				reg = <0xb0050000 0x1000>;
-				interrupts = <17>;
-				fifosize = <128>;
-				clocks = <&clks 13>;
-				dmas = <&dmac1 5>, <&dmac0 2>;
-				dma-names = "rx", "tx";
-			};
-
-			uart1: uart@b0060000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-uart";
-				reg = <0xb0060000 0x1000>;
-				interrupts = <18>;
-				fifosize = <32>;
-				clocks = <&clks 14>;
-				dma-names = "no-rx", "no-tx";
-			};
-
-			uart2: uart@b0070000 {
-				cell-index = <2>;
-				compatible = "sirf,prima2-uart";
-				reg = <0xb0070000 0x1000>;
-				interrupts = <19>;
-				fifosize = <128>;
-				clocks = <&clks 15>;
-				dmas = <&dmac0 6>, <&dmac0 7>;
-				dma-names = "rx", "tx";
-			};
-
-			usp0: usp@b0080000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-usp";
-				reg = <0xb0080000 0x10000>;
-				interrupts = <20>;
-				fifosize = <128>;
-				clocks = <&clks 28>;
-				dmas = <&dmac1 1>, <&dmac1 2>;
-				dma-names = "rx", "tx";
-			};
-
-			usp1: usp@b0090000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-usp";
-				reg = <0xb0090000 0x10000>;
-				interrupts = <21>;
-				fifosize = <128>;
-				clocks = <&clks 29>;
-				dmas = <&dmac0 14>, <&dmac0 15>;
-				dma-names = "rx", "tx";
-			};
-
-			dmac0: dma-controller@b00b0000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-dmac";
-				reg = <0xb00b0000 0x10000>;
-				interrupts = <12>;
-				clocks = <&clks 24>;
-				#dma-cells = <1>;
-			};
-
-			dmac1: dma-controller@b0160000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-dmac";
-				reg = <0xb0160000 0x10000>;
-				interrupts = <13>;
-				clocks = <&clks 25>;
-				#dma-cells = <1>;
-			};
-
-			vip@b00C0000 {
-				compatible = "sirf,prima2-vip";
-				reg = <0xb00C0000 0x10000>;
-				clocks = <&clks 31>;
-				interrupts = <14>;
-				sirf,vip-dma-rx-channel = <16>;
-			};
-
-			spi0: spi@b00d0000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-spi";
-				reg = <0xb00d0000 0x10000>;
-				interrupts = <15>;
-				sirf,spi-num-chipselects = <1>;
-				dmas = <&dmac1 9>,
-				     <&dmac1 4>;
-				dma-names = "rx", "tx";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				clocks = <&clks 19>;
-				resets = <&rstc 26>;
-				status = "disabled";
-			};
-
-			spi1: spi@b0170000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-spi";
-				reg = <0xb0170000 0x10000>;
-				interrupts = <16>;
-				sirf,spi-num-chipselects = <1>;
-				dmas = <&dmac0 12>,
-				     <&dmac0 13>;
-				dma-names = "rx", "tx";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				clocks = <&clks 20>;
-				resets = <&rstc 27>;
-				status = "disabled";
-			};
-
-			i2c0: i2c@b00e0000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-i2c";
-				reg = <0xb00e0000 0x10000>;
-				interrupts = <24>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				clocks = <&clks 17>;
-			};
-
-			i2c1: i2c@b00f0000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-i2c";
-				reg = <0xb00f0000 0x10000>;
-				interrupts = <25>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				clocks = <&clks 18>;
-			};
-
-			tsc@b0110000 {
-				compatible = "sirf,prima2-tsc";
-				reg = <0xb0110000 0x10000>;
-				interrupts = <33>;
-				clocks = <&clks 16>;
-			};
-
-			gpio: pinctrl@b0120000 {
-				#gpio-cells = <2>;
-				#interrupt-cells = <2>;
-				compatible = "sirf,atlas6-pinctrl";
-				reg = <0xb0120000 0x10000>;
-				interrupts = <43 44 45 46 47>;
-				gpio-controller;
-				interrupt-controller;
-
-				lcd_16pins_a: lcd0@0 {
-					lcd {
-						sirf,pins = "lcd_16bitsgrp";
-						sirf,function = "lcd_16bits";
-					};
-				};
-				lcd_18pins_a: lcd0@1 {
-					lcd {
-						sirf,pins = "lcd_18bitsgrp";
-						sirf,function = "lcd_18bits";
-					};
-				};
-				lcd_24pins_a: lcd0@2 {
-					lcd {
-						sirf,pins = "lcd_24bitsgrp";
-						sirf,function = "lcd_24bits";
-					};
-				};
-				lcdrom_pins_a: lcdrom0@0 {
-					lcd {
-						sirf,pins = "lcdromgrp";
-						sirf,function = "lcdrom";
-					};
-				};
-				uart0_pins_a: uart0@0 {
-					uart {
-						sirf,pins = "uart0grp";
-						sirf,function = "uart0";
-					};
-				};
-				uart0_noflow_pins_a: uart0@1 {
-					uart {
-						sirf,pins = "uart0_nostreamctrlgrp";
-						sirf,function = "uart0_nostreamctrl";
-					};
-				};
-				uart1_pins_a: uart1@0 {
-					uart {
-						sirf,pins = "uart1grp";
-						sirf,function = "uart1";
-					};
-				};
-				uart2_pins_a: uart2@0 {
-					uart {
-						sirf,pins = "uart2grp";
-						sirf,function = "uart2";
-					};
-				};
-				uart2_noflow_pins_a: uart2@1 {
-					uart {
-						sirf,pins = "uart2_nostreamctrlgrp";
-						sirf,function = "uart2_nostreamctrl";
-					};
-				};
-				spi0_pins_a: spi0@0 {
-					spi {
-						sirf,pins = "spi0grp";
-						sirf,function = "spi0";
-					};
-				};
-				spi1_pins_a: spi1@0 {
-					spi {
-						sirf,pins = "spi1grp";
-						sirf,function = "spi1";
-					};
-				};
-				i2c0_pins_a: i2c0@0 {
-					i2c {
-						sirf,pins = "i2c0grp";
-						sirf,function = "i2c0";
-					};
-				};
-				i2c1_pins_a: i2c1@0 {
-					i2c {
-						sirf,pins = "i2c1grp";
-						sirf,function = "i2c1";
-					};
-				};
-                                pwm0_pins_a: pwm0@0 {
-                                        pwm {
-                                                sirf,pins = "pwm0grp";
-                                                sirf,function = "pwm0";
-                                        };
-                                };
-                                pwm1_pins_a: pwm1@0 {
-                                        pwm {
-                                                sirf,pins = "pwm1grp";
-                                                sirf,function = "pwm1";
-                                        };
-                                };
-                                pwm2_pins_a: pwm2@0 {
-                                        pwm {
-                                                sirf,pins = "pwm2grp";
-                                                sirf,function = "pwm2";
-                                        };
-                                };
-                                pwm3_pins_a: pwm3@0 {
-                                        pwm {
-                                                sirf,pins = "pwm3grp";
-                                                sirf,function = "pwm3";
-                                        };
-                                };
-				pwm4_pins_a: pwm4@0 {
-                                        pwm {
-                                                sirf,pins = "pwm4grp";
-                                                sirf,function = "pwm4";
-                                        };
-                                };
-                                gps_pins_a: gps@0 {
-                                        gps {
-                                                sirf,pins = "gpsgrp";
-                                                sirf,function = "gps";
-                                        };
-                                };
-                                vip_pins_a: vip@0 {
-                                        vip {
-                                                sirf,pins = "vipgrp";
-                                                sirf,function = "vip";
-                                        };
-                                };
-                                sdmmc0_pins_a: sdmmc0@0 {
-                                        sdmmc0 {
-                                                sirf,pins = "sdmmc0grp";
-                                                sirf,function = "sdmmc0";
-                                        };
-                                };
-                                sdmmc1_pins_a: sdmmc1@0 {
-                                        sdmmc1 {
-                                                sirf,pins = "sdmmc1grp";
-                                                sirf,function = "sdmmc1";
-                                        };
-                                };
-                                sdmmc2_pins_a: sdmmc2@0 {
-                                        sdmmc2 {
-                                                sirf,pins = "sdmmc2grp";
-                                                sirf,function = "sdmmc2";
-                                        };
-                                };
-				sdmmc2_nowp_pins_a: sdmmc2_nowp@0 {
-                                        sdmmc2_nowp {
-                                                sirf,pins = "sdmmc2_nowpgrp";
-                                                sirf,function = "sdmmc2_nowp";
-                                        };
-                                };
-                                sdmmc3_pins_a: sdmmc3@0 {
-                                        sdmmc3 {
-                                                sirf,pins = "sdmmc3grp";
-                                                sirf,function = "sdmmc3";
-                                        };
-                                };
-                                sdmmc5_pins_a: sdmmc5@0 {
-                                        sdmmc5 {
-                                                sirf,pins = "sdmmc5grp";
-                                                sirf,function = "sdmmc5";
-                                        };
-                                };
-				i2s_mclk_pins_a: i2s_mclk@0 {
-                                        i2s_mclk {
-                                                sirf,pins = "i2smclkgrp";
-                                                sirf,function = "i2s_mclk";
-                                        };
-                                };
-				i2s_ext_clk_input_pins_a: i2s_ext_clk_input@0 {
-                                        i2s_ext_clk_input {
-                                                sirf,pins = "i2s_ext_clk_inputgrp";
-                                                sirf,function = "i2s_ext_clk_input";
-                                        };
-                                };
-                                i2s_pins_a: i2s@0 {
-                                        i2s {
-                                                sirf,pins = "i2sgrp";
-                                                sirf,function = "i2s";
-                                        };
-                                };
-				i2s_no_din_pins_a: i2s_no_din@0 {
-                                        i2s_no_din {
-                                                sirf,pins = "i2s_no_dingrp";
-                                                sirf,function = "i2s_no_din";
-                                        };
-                                };
-				i2s_6chn_pins_a: i2s_6chn@0 {
-                                        i2s_6chn {
-                                                sirf,pins = "i2s_6chngrp";
-                                                sirf,function = "i2s_6chn";
-                                        };
-                                };
-                                ac97_pins_a: ac97@0 {
-                                        ac97 {
-                                                sirf,pins = "ac97grp";
-                                                sirf,function = "ac97";
-                                        };
-                                };
-                                nand_pins_a: nand@0 {
-                                        nand {
-                                                sirf,pins = "nandgrp";
-                                                sirf,function = "nand";
-                                        };
-                                };
-                                usp0_pins_a: usp0@0 {
-                                        usp0 {
-                                                sirf,pins = "usp0grp";
-                                                sirf,function = "usp0";
-                                        };
-                                };
-				usp0_uart_nostreamctrl_pins_a: usp0@1 {
-                                        usp0 {
-                                                sirf,pins = "usp0_uart_nostreamctrl_grp";
-                                                sirf,function = "usp0_uart_nostreamctrl";
-                                        };
-                                };
-				usp0_only_utfs_pins_a: usp0@2 {
-					usp0 {
-						sirf,pins = "usp0_only_utfs_grp";
-						sirf,function = "usp0_only_utfs";
-					};
-				};
-				usp0_only_urfs_pins_a: usp0@3 {
-					usp0 {
-						sirf,pins = "usp0_only_urfs_grp";
-						sirf,function = "usp0_only_urfs";
-					};
-				};
-                                usp1_pins_a: usp1@0 {
-                                        usp1 {
-                                                sirf,pins = "usp1grp";
-                                                sirf,function = "usp1";
-                                        };
-                                };
-				usp1_uart_nostreamctrl_pins_a: usp1@1 {
-                                        usp1 {
-                                                sirf,pins = "usp1_uart_nostreamctrl_grp";
-                                                sirf,function = "usp1_uart_nostreamctrl";
-                                        };
-                                };
-                                usb0_upli_drvbus_pins_a: usb0_upli_drvbus@0 {
-                                        usb0_upli_drvbus {
-                                                sirf,pins = "usb0_upli_drvbusgrp";
-                                                sirf,function = "usb0_upli_drvbus";
-                                        };
-                                };
-                                usb1_utmi_drvbus_pins_a: usb1_utmi_drvbus@0 {
-                                        usb1_utmi_drvbus {
-                                                sirf,pins = "usb1_utmi_drvbusgrp";
-                                                sirf,function = "usb1_utmi_drvbus";
-                                        };
-                                };
-                                usb1_dp_dn_pins_a: usb1_dp_dn@0 {
-                                        usb1_dp_dn {
-                                                sirf,pins = "usb1_dp_dngrp";
-                                                sirf,function = "usb1_dp_dn";
-                                        };
-                                };
-                                uart1_route_io_usb1_pins_a: uart1_route_io_usb1@0 {
-                                        uart1_route_io_usb1 {
-                                                sirf,pins = "uart1_route_io_usb1grp";
-                                                sirf,function = "uart1_route_io_usb1";
-                                        };
-                                };
-                                warm_rst_pins_a: warm_rst@0 {
-                                        warm_rst {
-                                                sirf,pins = "warm_rstgrp";
-                                                sirf,function = "warm_rst";
-                                        };
-                                };
-                                pulse_count_pins_a: pulse_count@0 {
-                                        pulse_count {
-                                                sirf,pins = "pulse_countgrp";
-                                                sirf,function = "pulse_count";
-                                        };
-                                };
-                                cko0_pins_a: cko0@0 {
-                                        cko0 {
-                                                sirf,pins = "cko0grp";
-                                                sirf,function = "cko0";
-                                        };
-                                };
-                                cko1_pins_a: cko1@0 {
-                                        cko1 {
-                                                sirf,pins = "cko1grp";
-                                                sirf,function = "cko1";
-                                        };
-                                };
-			};
-
-			pwm@b0130000 {
-				compatible = "sirf,prima2-pwm";
-				reg = <0xb0130000 0x10000>;
-				clocks = <&clks 21>;
-			};
-
-			efusesys@b0140000 {
-				compatible = "sirf,prima2-efuse";
-				reg = <0xb0140000 0x10000>;
-				clocks = <&clks 22>;
-			};
-
-			pulsec@b0150000 {
-				compatible = "sirf,prima2-pulsec";
-				reg = <0xb0150000 0x10000>;
-				interrupts = <48>;
-				clocks = <&clks 23>;
-			};
-
-			pci-iobg {
-				compatible = "sirf,prima2-pciiobg", "simple-bus";
-				#address-cells = <1>;
-				#size-cells = <1>;
-				ranges = <0x56000000 0x56000000 0x1b00000>;
-
-				sd0: sdhci@56000000 {
-					cell-index = <0>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56000000 0x100000>;
-					interrupts = <38>;
-					bus-width = <8>;
-					clocks = <&clks 36>;
-				};
-
-				sd1: sdhci@56100000 {
-					cell-index = <1>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56100000 0x100000>;
-					interrupts = <38>;
-					status = "disabled";
-					bus-width = <4>;
-					clocks = <&clks 36>;
-				};
-
-				sd2: sdhci@56200000 {
-					cell-index = <2>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56200000 0x100000>;
-					interrupts = <23>;
-					status = "disabled";
-					bus-width = <4>;
-					clocks = <&clks 37>;
-				};
-
-				sd3: sdhci@56300000 {
-					cell-index = <3>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56300000 0x100000>;
-					interrupts = <23>;
-					status = "disabled";
-					bus-width = <4>;
-					clocks = <&clks 37>;
-				};
-
-				sd5: sdhci@56500000 {
-					cell-index = <5>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56500000 0x100000>;
-					interrupts = <39>;
-					status = "disabled";
-					bus-width = <4>;
-					clocks = <&clks 38>;
-				};
-
-				pci-copy@57900000 {
-					compatible = "sirf,prima2-pcicp";
-					reg = <0x57900000 0x100000>;
-					interrupts = <40>;
-				};
-
-				rom-interface@57a00000 {
-					compatible = "sirf,prima2-romif";
-					reg = <0x57a00000 0x100000>;
-				};
-			};
-		};
-
-		rtc-iobg {
-			compatible = "sirf,prima2-rtciobg", "sirf-prima2-rtciobg-bus", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x80030000 0x10000>;
-
-			gpsrtc@1000 {
-				compatible = "sirf,prima2-gpsrtc";
-				reg = <0x1000 0x1000>;
-				interrupts = <55 56 57>;
-			};
-
-			sysrtc@2000 {
-				compatible = "sirf,prima2-sysrtc";
-				reg = <0x2000 0x1000>;
-				interrupts = <52 53 54>;
-			};
-
-			minigpsrtc@2000 {
-				compatible = "sirf,prima2-minigpsrtc";
-				reg = <0x2000 0x1000>;
-				interrupts = <54>;
-			};
-
-			pwrc@3000 {
-				compatible = "sirf,prima2-pwrc";
-				reg = <0x3000 0x1000>;
-				interrupts = <32>;
-			};
-		};
-
-		uus-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xb8000000 0xb8000000 0x40000>;
-
-			usb0: usb@b00e0000 {
-				compatible = "chipidea,ci13611a-prima2";
-				reg = <0xb8000000 0x10000>;
-				interrupts = <10>;
-				clocks = <&clks 40>;
-			};
-
-			usb1: usb@b00f0000 {
-				compatible = "chipidea,ci13611a-prima2";
-				reg = <0xb8010000 0x10000>;
-				interrupts = <11>;
-				clocks = <&clks 41>;
-			};
-
-			security@b00f0000 {
-				compatible = "sirf,prima2-security";
-				reg = <0xb8030000 0x10000>;
-				interrupts = <42>;
-				clocks = <&clks 7>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/atlas7-evb.dts b/arch/arm/boot/dts/atlas7-evb.dts
deleted file mode 100644
index e0515043d145..000000000000
--- a/arch/arm/boot/dts/atlas7-evb.dts
+++ /dev/null
@@ -1,127 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DTS file for CSR SiRFatlas7 Evaluation Board
- *
- * Copyright (c) 2014 Cambridge Silicon Radio Limited, a CSR plc group company.
- */
-
-/dts-v1/;
-
-/include/ "atlas7.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "CSR SiRFatlas7 Evaluation Board";
-	compatible = "sirf,atlas7-cb", "sirf,atlas7";
-
-	chosen {
-		bootargs = "console=ttySiRF1,115200 earlyprintk";
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x40000000 0x20000000>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		vpp_reserved: vpp_mem@5e800000 {
-			compatible = "sirf,reserved-memory";
-			reg = <0x5e800000 0x800000>;
-		};
-
-		nanddisk_reserved: nanddisk@46000000 {
-			reg = <0x46000000 0x200000>;
-			no-map;
-		};
-	};
-
-
-	noc {
-		mediam {
-			nand@17050000 {
-				memory-region = <&nanddisk_reserved>;
-			};
-		};
-
-		gnssm {
-			spi1: spi@18200000 {
-				status = "okay";
-				spiflash: macronix@0{
-					status = "okay";
-					compatible = "macronix,mx25l6405d";
-					reg = <0>;
-					spi-max-frequency = <37500000>;
-					spi-cpha;
-					spi-cpol;
-					#address-cells = <1>;
-					#size-cells = <1>;
-					partitions@0 {
-						label = "myspiboot";
-						reg = <0x0 0x800000>;
-					};
-				};
-			};
-		};
-
-		btm {
-			uart6: uart@11000000 {
-				status = "okay";
-				uart-has-rtscts;
-			};
-		};
-
-		disp-iobg {
-			vpp@13110000 {
-				memory-region = <&vpp_reserved>;
-			};
-		};
-
-		display0: display@0 {
-			compatible = "lvds-panel";
-			source = "lvds.0";
-
-			bl-gpios = <&gpio_1 63 0>;
-			data-lines  = <24>;
-
-			display-timings {
-				native-mode = <&timing0>;
-				timing0: timing0 {
-					clock-frequency = <60000000>;
-					hactive = <1024>;
-					vactive = <600>;
-					hfront-porch = <220>;
-					hback-porch = <100>;
-					hsync-len = <1>;
-					vback-porch = <10>;
-					vfront-porch = <25>;
-					vsync-len = <1>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-					de-active = <1>;
-					pixelclk-active = <1>;
-				};
-			};
-		};
-
-		gpio_keys {
-			compatible = "gpio-keys";
-			status = "okay";
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			rearview_key {
-				label = "rearview key";
-				linux,code = <KEY_CAMERA>;
-				gpios = <&gpio_1 3 GPIO_ACTIVE_LOW>;
-				debounce-interval = <100>;
-			};
-		};
-
-	};
-};
diff --git a/arch/arm/boot/dts/atlas7.dtsi b/arch/arm/boot/dts/atlas7.dtsi
deleted file mode 100644
index 99c9d9d9267f..000000000000
--- a/arch/arm/boot/dts/atlas7.dtsi
+++ /dev/null
@@ -1,1955 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DTS file for CSR SiRFatlas7 SoC
- *
- * Copyright (c) 2014 Cambridge Silicon Radio Limited, a CSR plc group company.
- */
-
-/ {
-	compatible = "sirf,atlas7";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&gic>;
-	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
-		serial5 = &uart5;
-		serial6 = &uart6;
-		serial9 = &usp2;
-		spi1 = &spi1;
-		spi2 = &usp1;
-		spi3 = &usp2;
-		spi4 = &usp3;
-	};
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			reg = <0>;
-		};
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			reg = <1>;
-		};
-	};
-
-	clocks {
-		xinw {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-			clock-output-names = "xinw";
-		};
-		xin {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <26000000>;
-			clock-output-names = "xin";
-		};
-	};
-
-	arm-pmu {
-		compatible = "arm,cortex-a7-pmu";
-		interrupts = <0 29 4>, <0 82 4>;
-	};
-
-	noc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x10000000 0x10000000 0xc0000000>;
-
-		gic: interrupt-controller@10301000 {
-			compatible = "arm,cortex-a9-gic";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x10301000 0x1000>,
-			     <0x10302000 0x0100>;
-		};
-
-		pmu_regulator: pmu_regulator@10E30020 {
-			compatible = "sirf,atlas7-pmu-ldo";
-			reg = <0x10E30020 0x4>;
-			ldo: ldo {
-				regulator-name = "ldo";
-			};
-		};
-
-		atlas7_codec: atlas7_codec@10E30000 {
-			#sound-dai-cells = <0>;
-			compatible = "sirf,atlas7-codec";
-			reg = <0x10E30000 0x400>;
-			clocks = <&car 62>;
-			ldo-supply = <&ldo>;
-		};
-
-		atlas7_iacc: atlas7_iacc@10D01000 {
-			#sound-dai-cells = <0>;
-			compatible = "sirf,atlas7-iacc";
-			reg = <0x10D01000 0x100>;
-			dmas = <&dmac3 0>, <&dmac3 7>, <&dmac3 8>,
-				<&dmac3 3>, <&dmac3 9>;
-			dma-names = "rx", "tx0", "tx1", "tx2", "tx3";
-			clocks = <&car 62>;
-		};
-
-		ipc@13240000 {
-			compatible = "sirf,atlas7-ipc";
-			ranges = <0x13240000 0x13240000 0x00010000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			hwspinlock {
-				compatible = "sirf,hwspinlock";
-				reg = <0x13240000 0x00010000>;
-
-				num-spinlocks = <30>;
-			};
-
-			ns_m3_rproc@0 {
-				compatible = "sirf,ns2m30-rproc";
-				reg = <0x13240000 0x00010000>;
-				interrupts = <0 123 0>;
-			};
-
-			ns_m3_rproc@1 {
-				compatible = "sirf,ns2m31-rproc";
-				reg = <0x13240000 0x00010000>;
-				interrupts = <0 126 0>;
-			};
-
-			ns_kal_rproc@0 {
-				compatible = "sirf,ns2kal0-rproc";
-				reg = <0x13240000 0x00010000>;
-				interrupts = <0 124 0>;
-			};
-
-			ns_kal_rproc@1 {
-				compatible = "sirf,ns2kal1-rproc";
-				reg = <0x13240000 0x00010000>;
-				interrupts = <0 127 0>;
-			};
-		};
-
-		pinctrl: ioc@18880000 {
-			compatible = "sirf,atlas7-ioc";
-			reg = <0x18880000 0x1000>,
-				<0x10E40000 0x1000>;
-
-			audio_ac97_pmx: audio_ac97@0 {
-				audio_ac97 {
-					groups = "audio_ac97_grp";
-					function = "audio_ac97";
-				};
-			};
-
-			audio_func_dbg_pmx: audio_func_dbg@0 {
-				audio_func_dbg {
-					groups = "audio_func_dbg_grp";
-					function = "audio_func_dbg";
-				};
-			};
-
-			audio_i2s_pmx: audio_i2s@0 {
-				audio_i2s {
-					groups = "audio_i2s_grp";
-					function = "audio_i2s";
-				};
-			};
-
-			audio_i2s_2ch_pmx: audio_i2s_2ch@0 {
-				audio_i2s_2ch {
-					groups = "audio_i2s_2ch_grp";
-					function = "audio_i2s_2ch";
-				};
-			};
-
-			audio_i2s_extclk_pmx: audio_i2s_extclk@0 {
-				audio_i2s_extclk {
-					groups = "audio_i2s_extclk_grp";
-					function = "audio_i2s_extclk";
-				};
-			};
-
-			audio_uart0_pmx: audio_uart0@0 {
-				audio_uart0 {
-					groups = "audio_uart0_grp";
-					function = "audio_uart0";
-				};
-			};
-
-			audio_uart1_pmx: audio_uart1@0 {
-				audio_uart1 {
-					groups = "audio_uart1_grp";
-					function = "audio_uart1";
-				};
-			};
-
-			audio_uart2_pmx0: audio_uart2@0 {
-				audio_uart2_0 {
-					groups = "audio_uart2_grp0";
-					function = "audio_uart2_m0";
-				};
-			};
-
-			audio_uart2_pmx1: audio_uart2@1 {
-				audio_uart2_1 {
-					groups = "audio_uart2_grp1";
-					function = "audio_uart2_m1";
-				};
-			};
-
-			c_can_trnsvr_pmx: c_can_trnsvr@0 {
-				c_can_trnsvr {
-					groups = "c_can_trnsvr_grp";
-					function = "c_can_trnsvr";
-				};
-			};
-
-			c0_can_pmx0: c0_can@0 {
-				c0_can_0 {
-					groups = "c0_can_grp0";
-					function = "c0_can_m0";
-				};
-			};
-
-			c0_can_pmx1: c0_can@1 {
-				c0_can_1 {
-					groups = "c0_can_grp1";
-					function = "c0_can_m1";
-				};
-			};
-
-			c1_can_pmx0: c1_can@0 {
-				c1_can_0 {
-					groups = "c1_can_grp0";
-					function = "c1_can_m0";
-				};
-			};
-
-			c1_can_pmx1: c1_can@1 {
-				c1_can_1 {
-					groups = "c1_can_grp1";
-					function = "c1_can_m1";
-				};
-			};
-
-			c1_can_pmx2: c1_can@2 {
-				c1_can_2 {
-					groups = "c1_can_grp2";
-					function = "c1_can_m2";
-				};
-			};
-
-			ca_audio_lpc_pmx: ca_audio_lpc@0 {
-				ca_audio_lpc {
-					groups = "ca_audio_lpc_grp";
-					function = "ca_audio_lpc";
-				};
-			};
-
-			ca_bt_lpc_pmx: ca_bt_lpc@0 {
-				ca_bt_lpc {
-					groups = "ca_bt_lpc_grp";
-					function = "ca_bt_lpc";
-				};
-			};
-
-			ca_coex_pmx: ca_coex@0 {
-				ca_coex {
-					groups = "ca_coex_grp";
-					function = "ca_coex";
-				};
-			};
-
-			ca_curator_lpc_pmx: ca_curator_lpc@0 {
-				ca_curator_lpc {
-					groups = "ca_curator_lpc_grp";
-					function = "ca_curator_lpc";
-				};
-			};
-
-			ca_pcm_debug_pmx: ca_pcm_debug@0 {
-				ca_pcm_debug {
-					groups = "ca_pcm_debug_grp";
-					function = "ca_pcm_debug";
-				};
-			};
-
-			ca_pio_pmx: ca_pio@0 {
-				ca_pio {
-					groups = "ca_pio_grp";
-					function = "ca_pio";
-				};
-			};
-
-			ca_sdio_debug_pmx: ca_sdio_debug@0 {
-				ca_sdio_debug {
-					groups = "ca_sdio_debug_grp";
-					function = "ca_sdio_debug";
-				};
-			};
-
-			ca_spi_pmx: ca_spi@0 {
-				ca_spi {
-					groups = "ca_spi_grp";
-					function = "ca_spi";
-				};
-			};
-
-			ca_trb_pmx: ca_trb@0 {
-				ca_trb {
-					groups = "ca_trb_grp";
-					function = "ca_trb";
-				};
-			};
-
-			ca_uart_debug_pmx: ca_uart_debug@0 {
-				ca_uart_debug {
-					groups = "ca_uart_debug_grp";
-					function = "ca_uart_debug";
-				};
-			};
-
-			clkc_pmx0: clkc@0 {
-				clkc_0 {
-					groups = "clkc_grp0";
-					function = "clkc_m0";
-				};
-			};
-
-			clkc_pmx1: clkc@1 {
-				clkc_1 {
-					groups = "clkc_grp1";
-					function = "clkc_m1";
-				};
-			};
-
-			gn_gnss_i2c_pmx: gn_gnss_i2c@0 {
-				gn_gnss_i2c {
-					groups = "gn_gnss_i2c_grp";
-					function = "gn_gnss_i2c";
-				};
-			};
-
-			gn_gnss_uart_nopause_pmx: gn_gnss_uart_nopause@0 {
-				gn_gnss_uart_nopause {
-					groups = "gn_gnss_uart_nopause_grp";
-					function = "gn_gnss_uart_nopause";
-				};
-			};
-
-			gn_gnss_uart_pmx: gn_gnss_uart@0 {
-				gn_gnss_uart {
-					groups = "gn_gnss_uart_grp";
-					function = "gn_gnss_uart";
-				};
-			};
-
-			gn_trg_spi_pmx0: gn_trg_spi@0 {
-				gn_trg_spi_0 {
-					groups = "gn_trg_spi_grp0";
-					function = "gn_trg_spi_m0";
-				};
-			};
-
-			gn_trg_spi_pmx1: gn_trg_spi@1 {
-				gn_trg_spi_1 {
-					groups = "gn_trg_spi_grp1";
-					function = "gn_trg_spi_m1";
-				};
-			};
-
-			cvbs_dbg_pmx: cvbs_dbg@0 {
-				cvbs_dbg {
-					groups = "cvbs_dbg_grp";
-					function = "cvbs_dbg";
-				};
-			};
-
-			cvbs_dbg_test_pmx0: cvbs_dbg_test@0 {
-				cvbs_dbg_test_0 {
-					groups = "cvbs_dbg_test_grp0";
-					function = "cvbs_dbg_test_m0";
-				};
-			};
-
-			cvbs_dbg_test_pmx1: cvbs_dbg_test@1 {
-				cvbs_dbg_test_1 {
-					groups = "cvbs_dbg_test_grp1";
-					function = "cvbs_dbg_test_m1";
-				};
-			};
-
-			cvbs_dbg_test_pmx2: cvbs_dbg_test@2 {
-				cvbs_dbg_test_2 {
-					groups = "cvbs_dbg_test_grp2";
-					function = "cvbs_dbg_test_m2";
-				};
-			};
-
-			cvbs_dbg_test_pmx3: cvbs_dbg_test@3 {
-				cvbs_dbg_test_3 {
-					groups = "cvbs_dbg_test_grp3";
-					function = "cvbs_dbg_test_m3";
-				};
-			};
-
-			cvbs_dbg_test_pmx4: cvbs_dbg_test@4 {
-				cvbs_dbg_test_4 {
-					groups = "cvbs_dbg_test_grp4";
-					function = "cvbs_dbg_test_m4";
-				};
-			};
-
-			cvbs_dbg_test_pmx5: cvbs_dbg_test@5 {
-				cvbs_dbg_test_5 {
-					groups = "cvbs_dbg_test_grp5";
-					function = "cvbs_dbg_test_m5";
-				};
-			};
-
-			cvbs_dbg_test_pmx6: cvbs_dbg_test@6 {
-				cvbs_dbg_test_6 {
-					groups = "cvbs_dbg_test_grp6";
-					function = "cvbs_dbg_test_m6";
-				};
-			};
-
-			cvbs_dbg_test_pmx7: cvbs_dbg_test@7 {
-				cvbs_dbg_test_7 {
-					groups = "cvbs_dbg_test_grp7";
-					function = "cvbs_dbg_test_m7";
-				};
-			};
-
-			cvbs_dbg_test_pmx8: cvbs_dbg_test@8 {
-				cvbs_dbg_test_8 {
-					groups = "cvbs_dbg_test_grp8";
-					function = "cvbs_dbg_test_m8";
-				};
-			};
-
-			cvbs_dbg_test_pmx9: cvbs_dbg_test@9 {
-				cvbs_dbg_test_9 {
-					groups = "cvbs_dbg_test_grp9";
-					function = "cvbs_dbg_test_m9";
-				};
-			};
-
-			cvbs_dbg_test_pmx10: cvbs_dbg_test@10 {
-				cvbs_dbg_test_10 {
-					groups = "cvbs_dbg_test_grp10";
-					function = "cvbs_dbg_test_m10";
-				};
-			};
-
-			cvbs_dbg_test_pmx11: cvbs_dbg_test@11 {
-				cvbs_dbg_test_11 {
-					groups = "cvbs_dbg_test_grp11";
-					function = "cvbs_dbg_test_m11";
-				};
-			};
-
-			cvbs_dbg_test_pmx12: cvbs_dbg_test@12 {
-				cvbs_dbg_test_12 {
-					groups = "cvbs_dbg_test_grp12";
-					function = "cvbs_dbg_test_m12";
-				};
-			};
-
-			cvbs_dbg_test_pmx13: cvbs_dbg_test@13 {
-				cvbs_dbg_test_13 {
-					groups = "cvbs_dbg_test_grp13";
-					function = "cvbs_dbg_test_m13";
-				};
-			};
-
-			cvbs_dbg_test_pmx14: cvbs_dbg_test@14 {
-				cvbs_dbg_test_14 {
-					groups = "cvbs_dbg_test_grp14";
-					function = "cvbs_dbg_test_m14";
-				};
-			};
-
-			cvbs_dbg_test_pmx15: cvbs_dbg_test@15 {
-				cvbs_dbg_test_15 {
-					groups = "cvbs_dbg_test_grp15";
-					function = "cvbs_dbg_test_m15";
-				};
-			};
-
-			gn_gnss_power_pmx: gn_gnss_power@0 {
-				gn_gnss_power {
-					groups = "gn_gnss_power_grp";
-					function = "gn_gnss_power";
-				};
-			};
-
-			gn_gnss_sw_status_pmx: gn_gnss_sw_status@0 {
-				gn_gnss_sw_status {
-					groups = "gn_gnss_sw_status_grp";
-					function = "gn_gnss_sw_status";
-				};
-			};
-
-			gn_gnss_eclk_pmx: gn_gnss_eclk@0 {
-				gn_gnss_eclk {
-					groups = "gn_gnss_eclk_grp";
-					function = "gn_gnss_eclk";
-				};
-			};
-
-			gn_gnss_irq1_pmx0: gn_gnss_irq1@0 {
-				gn_gnss_irq1_0 {
-					groups = "gn_gnss_irq1_grp0";
-					function = "gn_gnss_irq1_m0";
-				};
-			};
-
-			gn_gnss_irq2_pmx0: gn_gnss_irq2@0 {
-				gn_gnss_irq2_0 {
-					groups = "gn_gnss_irq2_grp0";
-					function = "gn_gnss_irq2_m0";
-				};
-			};
-
-			gn_gnss_tm_pmx: gn_gnss_tm@0 {
-				gn_gnss_tm {
-					groups = "gn_gnss_tm_grp";
-					function = "gn_gnss_tm";
-				};
-			};
-
-			gn_gnss_tsync_pmx: gn_gnss_tsync@0 {
-				gn_gnss_tsync {
-					groups = "gn_gnss_tsync_grp";
-					function = "gn_gnss_tsync";
-				};
-			};
-
-			gn_io_gnsssys_sw_cfg_pmx: gn_io_gnsssys_sw_cfg@0 {
-				gn_io_gnsssys_sw_cfg {
-					groups = "gn_io_gnsssys_sw_cfg_grp";
-					function = "gn_io_gnsssys_sw_cfg";
-				};
-			};
-
-			gn_trg_pmx0: gn_trg@0 {
-				gn_trg_0 {
-					groups = "gn_trg_grp0";
-					function = "gn_trg_m0";
-				};
-			};
-
-			gn_trg_pmx1: gn_trg@1 {
-				gn_trg_1 {
-					groups = "gn_trg_grp1";
-					function = "gn_trg_m1";
-				};
-			};
-
-			gn_trg_shutdown_pmx0: gn_trg_shutdown@0 {
-				gn_trg_shutdown_0 {
-					groups = "gn_trg_shutdown_grp0";
-					function = "gn_trg_shutdown_m0";
-				};
-			};
-
-			gn_trg_shutdown_pmx1: gn_trg_shutdown@1 {
-				gn_trg_shutdown_1 {
-					groups = "gn_trg_shutdown_grp1";
-					function = "gn_trg_shutdown_m1";
-				};
-			};
-
-			gn_trg_shutdown_pmx2: gn_trg_shutdown@2 {
-				gn_trg_shutdown_2 {
-					groups = "gn_trg_shutdown_grp2";
-					function = "gn_trg_shutdown_m2";
-				};
-			};
-
-			gn_trg_shutdown_pmx3: gn_trg_shutdown@3 {
-				gn_trg_shutdown_3 {
-					groups = "gn_trg_shutdown_grp3";
-					function = "gn_trg_shutdown_m3";
-				};
-			};
-
-			i2c0_pmx: i2c0@0 {
-				i2c0 {
-					groups = "i2c0_grp";
-					function = "i2c0";
-				};
-			};
-
-			i2c1_pmx: i2c1@0 {
-				i2c1 {
-					groups = "i2c1_grp";
-					function = "i2c1";
-				};
-			};
-
-			jtag_pmx0: jtag@0 {
-				jtag_0 {
-					groups = "jtag_grp0";
-					function = "jtag_m0";
-				};
-			};
-
-			ks_kas_spi_pmx0: ks_kas_spi@0 {
-				ks_kas_spi_0 {
-					groups = "ks_kas_spi_grp0";
-					function = "ks_kas_spi_m0";
-				};
-			};
-
-			ld_ldd_pmx: ld_ldd@0 {
-				ld_ldd {
-					groups = "ld_ldd_grp";
-					function = "ld_ldd";
-				};
-			};
-
-			ld_ldd_16bit_pmx: ld_ldd_16bit@0 {
-				ld_ldd_16bit {
-					groups = "ld_ldd_16bit_grp";
-					function = "ld_ldd_16bit";
-				};
-			};
-
-			ld_ldd_fck_pmx: ld_ldd_fck@0 {
-				ld_ldd_fck {
-					groups = "ld_ldd_fck_grp";
-					function = "ld_ldd_fck";
-				};
-			};
-
-			ld_ldd_lck_pmx: ld_ldd_lck@0 {
-				ld_ldd_lck {
-					groups = "ld_ldd_lck_grp";
-					function = "ld_ldd_lck";
-				};
-			};
-
-			lr_lcdrom_pmx: lr_lcdrom@0 {
-				lr_lcdrom {
-					groups = "lr_lcdrom_grp";
-					function = "lr_lcdrom";
-				};
-			};
-
-			lvds_analog_pmx: lvds_analog@0 {
-				lvds_analog {
-					groups = "lvds_analog_grp";
-					function = "lvds_analog";
-				};
-			};
-
-			nd_df_pmx: nd_df@0 {
-				nd_df {
-					groups = "nd_df_grp";
-					function = "nd_df";
-				};
-			};
-
-			nd_df_nowp_pmx: nd_df_nowp@0 {
-				nd_df_nowp {
-					groups = "nd_df_nowp_grp";
-					function = "nd_df_nowp";
-				};
-			};
-
-			ps_pmx: ps@0 {
-				ps {
-					groups = "ps_grp";
-					function = "ps";
-				};
-			};
-
-			pwc_core_on_pmx: pwc_core_on@0 {
-				pwc_core_on {
-					groups = "pwc_core_on_grp";
-					function = "pwc_core_on";
-				};
-			};
-
-			pwc_ext_on_pmx: pwc_ext_on@0 {
-				pwc_ext_on {
-					groups = "pwc_ext_on_grp";
-					function = "pwc_ext_on";
-				};
-			};
-
-			pwc_gpio3_clk_pmx: pwc_gpio3_clk@0 {
-				pwc_gpio3_clk {
-					groups = "pwc_gpio3_clk_grp";
-					function = "pwc_gpio3_clk";
-				};
-			};
-
-			pwc_io_on_pmx: pwc_io_on@0 {
-				pwc_io_on {
-					groups = "pwc_io_on_grp";
-					function = "pwc_io_on";
-				};
-			};
-
-			pwc_lowbatt_b_pmx0: pwc_lowbatt_b@0 {
-				pwc_lowbatt_b_0 {
-					groups = "pwc_lowbatt_b_grp0";
-					function = "pwc_lowbatt_b_m0";
-				};
-			};
-
-			pwc_mem_on_pmx: pwc_mem_on@0 {
-				pwc_mem_on {
-					groups = "pwc_mem_on_grp";
-					function = "pwc_mem_on";
-				};
-			};
-
-			pwc_on_key_b_pmx0: pwc_on_key_b@0 {
-				pwc_on_key_b_0 {
-					groups = "pwc_on_key_b_grp0";
-					function = "pwc_on_key_b_m0";
-				};
-			};
-
-			pwc_wakeup_src0_pmx: pwc_wakeup_src0@0 {
-				pwc_wakeup_src0 {
-					groups = "pwc_wakeup_src0_grp";
-					function = "pwc_wakeup_src0";
-				};
-			};
-
-			pwc_wakeup_src1_pmx: pwc_wakeup_src1@0 {
-				pwc_wakeup_src1 {
-					groups = "pwc_wakeup_src1_grp";
-					function = "pwc_wakeup_src1";
-				};
-			};
-
-			pwc_wakeup_src2_pmx: pwc_wakeup_src2@0 {
-				pwc_wakeup_src2 {
-					groups = "pwc_wakeup_src2_grp";
-					function = "pwc_wakeup_src2";
-				};
-			};
-
-			pwc_wakeup_src3_pmx: pwc_wakeup_src3@0 {
-				pwc_wakeup_src3 {
-					groups = "pwc_wakeup_src3_grp";
-					function = "pwc_wakeup_src3";
-				};
-			};
-
-			pw_cko0_pmx0: pw_cko0@0 {
-				pw_cko0_0 {
-					groups = "pw_cko0_grp0";
-					function = "pw_cko0_m0";
-				};
-			};
-
-			pw_cko0_pmx1: pw_cko0@1 {
-				pw_cko0_1 {
-					groups = "pw_cko0_grp1";
-					function = "pw_cko0_m1";
-				};
-			};
-
-			pw_cko0_pmx2: pw_cko0@2 {
-				pw_cko0_2 {
-					groups = "pw_cko0_grp2";
-					function = "pw_cko0_m2";
-				};
-			};
-
-			pw_cko1_pmx0: pw_cko1@0 {
-				pw_cko1_0 {
-					groups = "pw_cko1_grp0";
-					function = "pw_cko1_m0";
-				};
-			};
-
-			pw_cko1_pmx1: pw_cko1@1 {
-				pw_cko1_1 {
-					groups = "pw_cko1_grp1";
-					function = "pw_cko1_m1";
-				};
-			};
-
-			pw_i2s01_clk_pmx0: pw_i2s01_clk@0 {
-				pw_i2s01_clk_0 {
-					groups = "pw_i2s01_clk_grp0";
-					function = "pw_i2s01_clk_m0";
-				};
-			};
-
-			pw_i2s01_clk_pmx1: pw_i2s01_clk@1 {
-				pw_i2s01_clk_1 {
-					groups = "pw_i2s01_clk_grp1";
-					function = "pw_i2s01_clk_m1";
-				};
-			};
-
-			pw_pwm0_pmx: pw_pwm0@0 {
-				pw_pwm0 {
-					groups = "pw_pwm0_grp";
-					function = "pw_pwm0";
-				};
-			};
-
-			pw_pwm1_pmx: pw_pwm1@0 {
-				pw_pwm1 {
-					groups = "pw_pwm1_grp";
-					function = "pw_pwm1";
-				};
-			};
-
-			pw_pwm2_pmx0: pw_pwm2@0 {
-				pw_pwm2_0 {
-					groups = "pw_pwm2_grp0";
-					function = "pw_pwm2_m0";
-				};
-			};
-
-			pw_pwm2_pmx1: pw_pwm2@1 {
-				pw_pwm2_1 {
-					groups = "pw_pwm2_grp1";
-					function = "pw_pwm2_m1";
-				};
-			};
-
-			pw_pwm3_pmx0: pw_pwm3@0 {
-				pw_pwm3_0 {
-					groups = "pw_pwm3_grp0";
-					function = "pw_pwm3_m0";
-				};
-			};
-
-			pw_pwm3_pmx1: pw_pwm3@1 {
-				pw_pwm3_1 {
-					groups = "pw_pwm3_grp1";
-					function = "pw_pwm3_m1";
-				};
-			};
-
-			pw_pwm_cpu_vol_pmx0: pw_pwm_cpu_vol@0 {
-				pw_pwm_cpu_vol_0 {
-					groups = "pw_pwm_cpu_vol_grp0";
-					function = "pw_pwm_cpu_vol_m0";
-				};
-			};
-
-			pw_pwm_cpu_vol_pmx1: pw_pwm_cpu_vol@1 {
-				pw_pwm_cpu_vol_1 {
-					groups = "pw_pwm_cpu_vol_grp1";
-					function = "pw_pwm_cpu_vol_m1";
-				};
-			};
-
-			pw_backlight_pmx0: pw_backlight@0 {
-				pw_backlight_0 {
-					groups = "pw_backlight_grp0";
-					function = "pw_backlight_m0";
-				};
-			};
-
-			pw_backlight_pmx1: pw_backlight@1 {
-				pw_backlight_1 {
-					groups = "pw_backlight_grp1";
-					function = "pw_backlight_m1";
-				};
-			};
-
-			rg_eth_mac_pmx: rg_eth_mac@0 {
-				rg_eth_mac {
-					groups = "rg_eth_mac_grp";
-					function = "rg_eth_mac";
-				};
-			};
-
-			rg_gmac_phy_intr_n_pmx: rg_gmac_phy_intr_n@0 {
-				rg_gmac_phy_intr_n {
-					groups = "rg_gmac_phy_intr_n_grp";
-					function = "rg_gmac_phy_intr_n";
-				};
-			};
-
-			rg_rgmii_mac_pmx: rg_rgmii_mac@0 {
-				rg_rgmii_mac {
-					groups = "rg_rgmii_mac_grp";
-					function = "rg_rgmii_mac";
-				};
-			};
-
-			rg_rgmii_phy_ref_clk_pmx0: rg_rgmii_phy_ref_clk@0 {
-				rg_rgmii_phy_ref_clk_0 {
-					groups =
-						"rg_rgmii_phy_ref_clk_grp0";
-					function =
-						"rg_rgmii_phy_ref_clk_m0";
-				};
-			};
-
-			rg_rgmii_phy_ref_clk_pmx1: rg_rgmii_phy_ref_clk@1 {
-				rg_rgmii_phy_ref_clk_1 {
-					groups =
-						"rg_rgmii_phy_ref_clk_grp1";
-					function =
-						"rg_rgmii_phy_ref_clk_m1";
-				};
-			};
-
-			sd0_pmx: sd0@0 {
-				sd0 {
-					groups = "sd0_grp";
-					function = "sd0";
-				};
-			};
-
-			sd0_4bit_pmx: sd0_4bit@0 {
-				sd0_4bit {
-					groups = "sd0_4bit_grp";
-					function = "sd0_4bit";
-				};
-			};
-
-			sd1_pmx: sd1@0 {
-				sd1 {
-					groups = "sd1_grp";
-					function = "sd1";
-				};
-			};
-
-			sd1_4bit_pmx0: sd1_4bit@0 {
-				sd1_4bit_0 {
-					groups = "sd1_4bit_grp0";
-					function = "sd1_4bit_m0";
-				};
-			};
-
-			sd1_4bit_pmx1: sd1_4bit@1 {
-				sd1_4bit_1 {
-					groups = "sd1_4bit_grp1";
-					function = "sd1_4bit_m1";
-				};
-			};
-
-			sd2_pmx0: sd2@0 {
-				sd2_0 {
-					groups = "sd2_grp0";
-					function = "sd2_m0";
-				};
-			};
-
-			sd2_no_cdb_pmx0: sd2_no_cdb@0 {
-				sd2_no_cdb_0 {
-					groups = "sd2_no_cdb_grp0";
-					function = "sd2_no_cdb_m0";
-				};
-			};
-
-			sd3_pmx: sd3@0 {
-				sd3 {
-					groups = "sd3_grp";
-					function = "sd3";
-				};
-			};
-
-			sd5_pmx: sd5@0 {
-				sd5 {
-					groups = "sd5_grp";
-					function = "sd5";
-				};
-			};
-
-			sd6_pmx0: sd6@0 {
-				sd6_0 {
-					groups = "sd6_grp0";
-					function = "sd6_m0";
-				};
-			};
-
-			sd6_pmx1: sd6@1 {
-				sd6_1 {
-					groups = "sd6_grp1";
-					function = "sd6_m1";
-				};
-			};
-
-			sp0_ext_ldo_on_pmx: sp0_ext_ldo_on@0 {
-				sp0_ext_ldo_on {
-					groups = "sp0_ext_ldo_on_grp";
-					function = "sp0_ext_ldo_on";
-				};
-			};
-
-			sp0_qspi_pmx: sp0_qspi@0 {
-				sp0_qspi {
-					groups = "sp0_qspi_grp";
-					function = "sp0_qspi";
-				};
-			};
-
-			sp1_spi_pmx: sp1_spi@0 {
-				sp1_spi {
-					groups = "sp1_spi_grp";
-					function = "sp1_spi";
-				};
-			};
-
-			tpiu_trace_pmx: tpiu_trace@0 {
-				tpiu_trace {
-					groups = "tpiu_trace_grp";
-					function = "tpiu_trace";
-				};
-			};
-
-			uart0_pmx: uart0@0 {
-				uart0 {
-					groups = "uart0_grp";
-					function = "uart0";
-				};
-			};
-
-			uart0_nopause_pmx: uart0_nopause@0 {
-				uart0_nopause {
-					groups = "uart0_nopause_grp";
-					function = "uart0_nopause";
-				};
-			};
-
-			uart1_pmx: uart1@0 {
-				uart1 {
-					groups = "uart1_grp";
-					function = "uart1";
-				};
-			};
-
-			uart2_pmx: uart2@0 {
-				uart2 {
-					groups = "uart2_grp";
-					function = "uart2";
-				};
-			};
-
-			uart3_pmx0: uart3@0 {
-				uart3_0 {
-					groups = "uart3_grp0";
-					function = "uart3_m0";
-				};
-			};
-
-			uart3_pmx1: uart3@1 {
-				uart3_1 {
-					groups = "uart3_grp1";
-					function = "uart3_m1";
-				};
-			};
-
-			uart3_pmx2: uart3@2 {
-				uart3_2 {
-					groups = "uart3_grp2";
-					function = "uart3_m2";
-				};
-			};
-
-			uart3_pmx3: uart3@3 {
-				uart3_3 {
-					groups = "uart3_grp3";
-					function = "uart3_m3";
-				};
-			};
-
-			uart3_nopause_pmx0: uart3_nopause@0 {
-				uart3_nopause_0 {
-					groups = "uart3_nopause_grp0";
-					function = "uart3_nopause_m0";
-				};
-			};
-
-			uart3_nopause_pmx1: uart3_nopause@1 {
-				uart3_nopause_1 {
-					groups = "uart3_nopause_grp1";
-					function = "uart3_nopause_m1";
-				};
-			};
-
-			uart4_pmx0: uart4@0 {
-				uart4_0 {
-					groups = "uart4_grp0";
-					function = "uart4_m0";
-				};
-			};
-
-			uart4_pmx1: uart4@1 {
-				uart4_1 {
-					groups = "uart4_grp1";
-					function = "uart4_m1";
-				};
-			};
-
-			uart4_pmx2: uart4@2 {
-				uart4_2 {
-					groups = "uart4_grp2";
-					function = "uart4_m2";
-				};
-			};
-
-			uart4_nopause_pmx: uart4_nopause@0 {
-				uart4_nopause {
-					groups = "uart4_nopause_grp";
-					function = "uart4_nopause";
-				};
-			};
-
-			usb0_drvvbus_pmx: usb0_drvvbus@0 {
-				usb0_drvvbus {
-					groups = "usb0_drvvbus_grp";
-					function = "usb0_drvvbus";
-				};
-			};
-
-			usb1_drvvbus_pmx: usb1_drvvbus@0 {
-				usb1_drvvbus {
-					groups = "usb1_drvvbus_grp";
-					function = "usb1_drvvbus";
-				};
-			};
-
-			visbus_dout_pmx: visbus_dout@0 {
-				visbus_dout {
-					groups = "visbus_dout_grp";
-					function = "visbus_dout";
-				};
-			};
-
-			vi_vip1_pmx: vi_vip1@0 {
-				vi_vip1 {
-					groups = "vi_vip1_grp";
-					function = "vi_vip1";
-				};
-			};
-
-			vi_vip1_ext_pmx: vi_vip1_ext@0 {
-				vi_vip1_ext {
-					groups = "vi_vip1_ext_grp";
-					function = "vi_vip1_ext";
-				};
-			};
-
-			vi_vip1_low8bit_pmx: vi_vip1_low8bit@0 {
-				vi_vip1_low8bit {
-					groups = "vi_vip1_low8bit_grp";
-					function = "vi_vip1_low8bit";
-				};
-			};
-
-			vi_vip1_high8bit_pmx: vi_vip1_high8bit@0 {
-				vi_vip1_high8bit {
-					groups = "vi_vip1_high8bit_grp";
-					function = "vi_vip1_high8bit";
-				};
-			};
-		};
-
-		pmipc {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x13240000 0x13240000 0x00010000>;
-			pmipc@0x13240000 {
-				compatible = "sirf,atlas7-pmipc";
-				reg = <0x13240000 0x00010000>;
-			};
-		};
-
-		dramfw {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x10830000 0x10830000 0x18000>;
-			dramfw@10820000 {
-				compatible = "sirf,nocfw-dramfw";
-				reg = <0x10830000 0x18000>;
-			};
-		};
-
-		spramfw {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x10250000 0x10250000 0x3000>;
-			spramfw@10820000 {
-				compatible = "sirf,nocfw-spramfw";
-				reg = <0x10250000 0x3000>;
-			};
-		};
-
-		cpum {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x10200000 0x10200000 0x3000>;
-			cpum@10200000 {
-				compatible = "sirf,nocfw-cpum";
-				reg = <0x10200000 0x3000>;
-			};
-		};
-
-		cgum {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x18641000 0x18641000 0x3000>,
-					 <0x18620000 0x18620000 0x1000>,
-					<0x18630000 0x18630000 0x10000>;
-
-			cgum@18641000 {
-				compatible = "sirf,nocfw-cgum";
-				reg = <0x18641000 0x3000>;
-			};
-
-			car: clock-controller@18620000 {
-				compatible = "sirf,atlas7-car";
-				reg = <0x18620000 0x1000>;
-				#clock-cells = <1>;
-				#reset-cells = <1>;
-			};
-			pwm: pwm@18630000 {
-				compatible = "sirf,prima2-pwm";
-				#pwm-cells = <2>;
-				reg = <0x18630000 0x10000>;
-				clocks = <&car 138>, <&car 139>, <&car 237>,
-					<&car 240>,  <&car 140>, <&car 246>;
-				clock-names = "pwmc", "sigsrc0", "sigsrc1",
-					"sigsrc2", "sigsrc3", "sigsrc4";
-			};
-		};
-
-		gnssm {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x18000000 0x18000000 0x0000ffff>,
-				<0x18010000 0x18010000 0x1000>,
-				<0x18020000 0x18020000 0x1000>,
-				<0x18030000 0x18030000 0x1000>,
-				<0x18040000 0x18040000 0x1000>,
-				<0x18050000 0x18050000 0x1000>,
-				<0x18060000 0x18060000 0x1000>,
-				<0x180b0000 0x180b0000 0x4000>,
-				<0x18100000 0x18100000 0x3000>,
-				<0x18250000 0x18250000 0x10000>,
-				<0x18200000 0x18200000 0x1000>;
-
-			dmac0: dma-controller@18000000 {
-				cell-index = <0>;
-				compatible = "sirf,atlas7-dmac";
-				reg = <0x18000000 0x1000>;
-				interrupts = <0 12 0>;
-				clocks = <&car 89>;
-				dma-channels = <16>;
-				#dma-cells = <1>;
-			};
-
-			gnssmfw@0x18100000 {
-				compatible = "sirf,nocfw-gnssm";
-				reg = <0x18100000 0x3000>;
-			};
-
-			uart0: uart@18010000 {
-				cell-index = <0>;
-				compatible = "sirf,atlas7-uart";
-				reg = <0x18010000 0x1000>;
-				interrupts = <0 17 0>;
-				clocks = <&car 90>;
-				fifosize = <128>;
-				dmas = <&dmac0 3>, <&dmac0 2>;
-				dma-names = "rx", "tx";
-			};
-
-			uart1: uart@18020000 {
-				cell-index = <1>;
-				compatible = "sirf,atlas7-uart";
-				reg = <0x18020000 0x1000>;
-				interrupts = <0 18 0>;
-				clocks = <&car 88>;
-				fifosize = <32>;
-			};
-
-			uart2: uart@18030000 {
-				cell-index = <2>;
-				compatible = "sirf,atlas7-uart";
-				reg = <0x18030000 0x1000>;
-				interrupts = <0 19 0>;
-				clocks = <&car 91>;
-				fifosize = <128>;
-				dmas = <&dmac0 6>, <&dmac0 7>;
-				dma-names = "rx", "tx";
-				status = "disabled";
-			};
-			uart3: uart@18040000 {
-				cell-index = <3>;
-				compatible = "sirf,atlas7-uart";
-				reg = <0x18040000 0x1000>;
-				interrupts = <0 66 0>;
-				clocks = <&car 92>;
-				fifosize = <128>;
-				dmas = <&dmac0 4>, <&dmac0 5>;
-				dma-names = "rx", "tx";
-				status = "disabled";
-			};
-			uart4: uart@18050000 {
-				cell-index = <4>;
-				compatible = "sirf,atlas7-uart";
-				reg = <0x18050000 0x1000>;
-				interrupts = <0 69 0>;
-				clocks = <&car 93>;
-				fifosize = <128>;
-				dmas = <&dmac0 0>, <&dmac0 1>;
-				dma-names = "rx", "tx";
-				status = "disabled";
-			};
-			uart5: uart@18060000 {
-				cell-index = <5>;
-				compatible = "sirf,atlas7-uart";
-				reg = <0x18060000 0x1000>;
-				interrupts = <0 71 0>;
-				clocks = <&car 94>;
-				fifosize = <128>;
-				dmas = <&dmac0 8>, <&dmac0 9>;
-				dma-names = "rx", "tx";
-				status = "disabled";
-			};
-			gmac: eth@180b0000 {
-				compatible = "snps, dwc-eth-qos";
-				reg = <0x180b0000 0x4000>;
-				interrupts = <0 59 0>, <0 70 0>;
-				interrupt-names = "macirq", "macpmt";
-				clocks = <&car 39>, <&car 45>,
-				       <&car 86>, <&car 87>;
-				clock-names = "gnssm_rgmii", "gnssm_gmac",
-					"rgmii", "gmac";
-				local-mac-address = [00 00 00 00 00 00];
-				phy-mode = "rgmii";
-			};
-			dspub@18250000 {
-				compatible = "dx,cc44p";
-				reg = <0x18250000 0x10000>;
-				interrupts = <0 27 0>;
-			};
-
-			spi1: spi@18200000 {
-				compatible = "sirf,prima2-spi";
-				reg = <0x18200000 0x1000>;
-				interrupts = <0 16 0>;
-				clocks = <&car 95>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				dmas = <&dmac0 12>, <&dmac0 13>;
-				dma-names = "rx", "tx";
-				status = "disabled";
-			};
-		};
-
-
-		gpum {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x13000000 0x13000000 0x3000>,
-				<0x13010000 0x13010000 0x1400>,
-				<0x13010800 0x13010800 0x100>,
-				<0x13011000 0x13011000 0x100>;
-			gpum@0x13000000 {
-				compatible = "sirf,nocfw-gpum";
-				reg = <0x13000000 0x3000>;
-			};
-			dmacsdrr: dma-controller@13010800 {
-				cell-index = <5>;
-				compatible = "sirf,atlas7-dmac-v2";
-				reg = <0x13010800 0x100>;
-				interrupts = <0 8 0>;
-				clocks = <&car 127>;
-				#dma-cells = <1>;
-				#dma-channels = <1>;
-			};
-			dmacsdrw: dma-controller@13011000 {
-				cell-index = <6>;
-				compatible = "sirf,atlas7-dmac-v2";
-				reg = <0x13011000 0x100>;
-				interrupts = <0 9 0>;
-				clocks = <&car 127>;
-				#dma-cells = <1>;
-				#dma-channels = <1>;
-			};
-			sdr@0x13010000 {
-				compatible = "sirf,atlas7-sdr";
-				reg = <0x13010000 0x1400>;
-				interrupts = <0 7 0>,
-					   <0 8 0>,
-					   <0 9 0>;
-				clocks = <&car 127>;
-				dmas = <&dmacsdrr 0>, <&dmacsdrw 0>;
-				dma-names = "tx", "rx";
-			};
-		};
-
-		mediam {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x15000000 0x15000000 0x00600000>,
-				<0x16000000 0x16000000 0x00200000>,
-				<0x17000000 0x17000000 0x10000>,
-				<0x17020000 0x17020000 0x1000>,
-				<0x17030000 0x17030000 0x1000>,
-				<0x17040000 0x17040000 0x1000>,
-				<0x17050000 0x17050000 0x10000>,
-				<0x17060000 0x17060000 0x200>,
-				<0x17060200 0x17060200 0x100>,
-				<0x17070000 0x17070000 0x200>,
-				<0x17070200 0x17070200 0x100>,
-				<0x170A0000 0x170A0000 0x3000>;
-
-			multimedia@15000000 {
-				compatible = "sirf,atlas7-video-codec";
-				reg = <0x15000000 0x10000>;
-				interrupts = <0 5 0>;
-				clocks = <&car 102>;
-			};
-
-			mediam@170A0000 {
-				compatible = "sirf,nocfw-mediam";
-				reg = <0x170A0000 0x3000>;
-			};
-
-			gpio_0: gpio_mediam@17040000 {
-				#gpio-cells = <2>;
-				#interrupt-cells = <2>;
-				compatible = "sirf,atlas7-gpio";
-				reg = <0x17040000 0x1000>;
-				interrupts = <0 13 0>, <0 14 0>;
-				clocks = <&car 107>;
-				clock-names = "gpio0_io";
-				gpio-controller;
-				interrupt-controller;
-
-				gpio-banks = <2>;
-				gpio-ranges = <&pinctrl 0 0 0>,
-						<&pinctrl 32 0 0>;
-				gpio-ranges-group-names = "lvds_gpio_grp",
-							"uart_nand_gpio_grp";
-			};
-
-			nand@17050000 {
-				compatible = "sirf,atlas7-nand";
-				reg = <0x17050000 0x10000>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&nd_df_pmx>;
-				interrupts = <0 41 0>;
-				clocks = <&car 108>, <&car 112>;
-				clock-names = "nand_io", "nand_nand";
-			};
-
-			sd0: sdhci@16000000 {
-				cell-index = <0>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x16000000 0x100000>;
-				interrupts = <0 38 0>;
-				clocks = <&car 109>, <&car 111>;
-				clock-names = "core", "iface";
-				wp-inverted;
-				non-removable;
-				status = "disabled";
-				bus-width = <8>;
-			};
-
-			sd1: sdhci@16100000 {
-				cell-index = <1>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x16100000 0x100000>;
-				interrupts = <0 38 0>;
-				clocks = <&car 109>, <&car 111>;
-				clock-names = "core", "iface";
-				non-removable;
-				status = "disabled";
-				bus-width = <8>;
-			};
-
-			jpeg@17000000 {
-				compatible = "sirf,atlas7-jpeg";
-				reg = <0x17000000 0x10000>;
-				interrupts = <0 72 0>,
-					<0 73 0>;
-				clocks = <&car 103>;
-			};
-
-			usb0: usb@17060000 {
-				cell-index = <0>;
-				compatible = "sirf,atlas7-usb";
-				reg = <0x17060000 0x200>;
-				interrupts = <0 10 0>;
-				clocks = <&car 113>;
-				sirf,usbphy = <&usbphy0>;
-				phy_type = "utmi";
-				dr_mode = "otg";
-				maximum-speed = "high-speed";
-				status = "okay";
-			};
-
-			usb1: usb@17070000 {
-				cell-index = <1>;
-				compatible = "sirf,atlas7-usb";
-				reg = <0x17070000 0x200>;
-				interrupts = <0 11 0>;
-				clocks = <&car 114>;
-				sirf,usbphy = <&usbphy1>;
-				phy_type = "utmi";
-				dr_mode = "host";
-				maximum-speed = "high-speed";
-				status = "okay";
-			};
-
-			usbphy0: usbphy@0 {
-				compatible = "sirf,atlas7-usbphy";
-				reg = <0x17060200 0x100>;
-				clocks = <&car 115>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@1 {
-				compatible = "sirf,atlas7-usbphy";
-				reg = <0x17070200 0x100>;
-				clocks = <&car 116>;
-				status = "okay";
-			};
-
-			i2c0: i2c@17020000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-i2c";
-				reg = <0x17020000 0x1000>;
-				interrupts = <0 24 0>;
-				clocks = <&car 105>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-		};
-
-		vdifm {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x13290000 0x13290000 0x3000>,
-				<0x13300000 0x13300000 0x1000>,
-				<0x14200000 0x14200000 0x600000>;
-
-			vdifm@13290000 {
-				compatible = "sirf,nocfw-vdifm";
-				reg = <0x13290000 0x3000>;
-			};
-
-			gpio_1: gpio_vdifm@13300000 {
-				#gpio-cells = <2>;
-				#interrupt-cells = <2>;
-				compatible = "sirf,atlas7-gpio";
-				reg = <0x13300000 0x1000>;
-				interrupts = <0 43 0>, <0 44 0>,
-						<0 45 0>, <0 46 0>;
-				clocks = <&car 84>;
-				clock-names = "gpio1_io";
-				gpio-controller;
-				interrupt-controller;
-
-				gpio-banks = <4>;
-				gpio-ranges = <&pinctrl 0 0 0>,
-						<&pinctrl 32 0 0>,
-						<&pinctrl 64 0 0>,
-						<&pinctrl 96 0 0>;
-				gpio-ranges-group-names = "gnss_gpio_grp",
-							"lcd_vip_gpio_grp",
-							"sdio_i2s_gpio_grp",
-							"sp_rgmii_gpio_grp";
-			};
-
-			sd2: sdhci@14200000 {
-				cell-index = <2>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x14200000 0x100000>;
-				interrupts = <0 23 0>;
-				clocks = <&car 70>, <&car 75>;
-				clock-names = "core", "iface";
-				status = "disabled";
-				bus-width = <4>;
-				sd-uhs-sdr50;
-				vqmmc-supply = <&vqmmc>;
-				vqmmc: vqmmc@2 {
-					regulator-min-microvolt = <1650000>;
-					regulator-max-microvolt = <1950000>;
-					regulator-name = "vqmmc-ldo";
-					regulator-type = "voltage";
-					regulator-boot-on;
-					regulator-allow-bypass;
-				};
-			};
-
-			sd3: sdhci@14300000 {
-				cell-index = <3>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x14300000 0x100000>;
-				interrupts = <0 23 0>;
-				clocks = <&car 76>, <&car 81>;
-				clock-names = "core", "iface";
-				status = "disabled";
-				bus-width = <4>;
-			};
-
-			sd5: sdhci@14500000 {
-				cell-index = <5>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x14500000 0x100000>;
-				interrupts = <0 39 0>;
-				clocks = <&car 71>, <&car 76>;
-				clock-names = "core", "iface";
-				status = "disabled";
-				bus-width = <4>;
-				loop-dma;
-			};
-
-			sd6: sdhci@14600000 {
-				cell-index = <6>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x14600000 0x100000>;
-				interrupts = <0 98 0>;
-				clocks = <&car 72>, <&car 77>;
-				clock-names = "core", "iface";
-				status = "disabled";
-				bus-width = <4>;
-			};
-
-			sd7: sdhci@14700000 {
-				cell-index = <7>;
-				compatible = "sirf,atlas7-sdhc";
-				reg = <0x14700000 0x100000>;
-				interrupts = <0 98 0>;
-				clocks = <&car 72>, <&car 77>;
-				clock-names = "core", "iface";
-				status = "disabled";
-				bus-width = <4>;
-			};
-		};
-
-		audiom {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x10d50000 0x10d50000 0x0000ffff>,
-					<0x10d60000 0x10d60000 0x0000ffff>,
-					<0x10d80000 0x10d80000 0x0000ffff>,
-					<0x10d90000 0x10d90000 0x0000ffff>,
-					<0x10ED0000 0x10ED0000 0x3000>,
-					<0x10dc8000 0x10dc8000 0x1000>,
-					<0x10dc0000 0x10dc0000 0x1000>,
-					<0x10db0000 0x10db0000 0x4000>,
-					<0x10d40000 0x10d40000 0x1000>,
-					<0x10d30000 0x10d30000 0x1000>;
-
-			timer@10dc0000 {
-				compatible = "sirf,atlas7-tick";
-				reg = <0x10dc0000 0x1000>;
-				interrupts = <0 0 0>,
-					   <0 1 0>,
-					   <0 2 0>,
-					   <0 49 0>,
-					   <0 50 0>,
-					   <0 51 0>;
-				clocks = <&car 47>;
-			};
-
-			timerb@10dc8000 {
-					compatible = "sirf,atlas7-tick";
-					reg = <0x10dc8000 0x1000>;
-					interrupts = <0 74 0>,
-							   <0 75 0>,
-							   <0 76 0>,
-							   <0 77 0>,
-							   <0 78 0>,
-							   <0 79 0>;
-					clocks = <&car 47>;
-			};
-
-			vip0@10db0000 {
-				compatible = "sirf,atlas7-vip0";
-				reg = <0x10db0000 0x2000>;
-				interrupts = <0 85 0>;
-				sirf,vip_cma_size = <0xC00000>;
-			};
-
-			cvd@10db2000 {
-				compatible = "sirf,cvd";
-				reg = <0x10db2000 0x2000>;
-				clocks = <&car 46>;
-			};
-
-			dmac2: dma-controller@10d50000 {
-				cell-index = <2>;
-				compatible = "sirf,atlas7-dmac";
-				reg = <0x10d50000 0xffff>;
-				interrupts = <0 55 0>;
-				clocks = <&car 60>;
-				dma-channels = <16>;
-				#dma-cells = <1>;
-			};
-
-			dmac3: dma-controller@10d60000 {
-				cell-index = <3>;
-				compatible = "sirf,atlas7-dmac";
-				reg = <0x10d60000 0xffff>;
-				interrupts = <0 56 0>;
-				clocks = <&car 61>;
-				dma-channels = <16>;
-				#dma-cells = <1>;
-			};
-
-			adc: adc@10d80000 {
-				compatible = "sirf,atlas7-adc";
-				reg = <0x10d80000 0xffff>;
-				interrupts = <0 34 0>;
-				clocks = <&car 49>;
-				#io-channel-cells = <1>;
-			};
-
-			pulsec@10d90000 {
-				compatible = "sirf,prima2-pulsec";
-				reg = <0x10d90000 0xffff>;
-				interrupts = <0 42 0>;
-				clocks = <&car 54>;
-			};
-
-			audiom@10ED0000 {
-				compatible = "sirf,nocfw-audiom";
-				reg = <0x10ED0000 0x3000>;
-				interrupts = <0 102 0>;
-			};
-
-			usp1: usp@10d30000 {
-				cell-index = <1>;
-				reg = <0x10d30000 0x1000>;
-				fifosize = <512>;
-				clocks = <&car 58>;
-				dmas = <&dmac2 6>, <&dmac2 7>;
-				dma-names = "rx", "tx";
-			};
-
-			usp2: usp@10d40000 {
-				cell-index = <2>;
-				reg = <0x10d40000 0x1000>;
-				interrupts = <0 22 0>;
-				clocks = <&car 59>;
-				dmas = <&dmac2 12>, <&dmac2 13>;
-				dma-names = "rx", "tx";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				status = "disabled";
-			};
-		};
-
-		ddrm {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x10820000 0x10820000 0x3000>,
-					<0x10800000 0x10800000 0x2000>;
-			ddrm@10820000 {
-				compatible = "sirf,nocfw-ddrm";
-				reg = <0x10820000 0x3000>;
-				interrupts = <0 105 0>;
-			};
-
-			memory-controller@0x10800000 {
-				compatible = "sirf,atlas7-memc";
-				reg = <0x10800000 0x2000>;
-			};
-
-		};
-
-		btm {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x11002000 0x11002000 0x0000ffff>,
-			       <0x11010000 0x11010000 0x3000>,
-			       <0x11000000 0x11000000 0x1000>,
-			       <0x11001000 0x11001000 0x1000>;
-
-			dmac4: dma-controller@11002000 {
-				cell-index = <4>;
-				compatible = "sirf,atlas7-dmac";
-				reg = <0x11002000 0x1000>;
-				interrupts = <0 99 0>;
-				clocks = <&car 130>;
-				dma-channels = <16>;
-				#dma-cells = <1>;
-			};
-			uart6: uart@11000000 {
-				cell-index = <6>;
-				compatible = "sirf,atlas7-bt-uart",
-						"sirf,atlas7-uart";
-				reg = <0x11000000 0x1000>;
-				interrupts = <0 100 0>;
-				clocks = <&car 131>, <&car 133>, <&car 134>;
-				clock-names = "uart", "general", "noc";
-				fifosize = <128>;
-				dmas = <&dmac4 12>, <&dmac4 13>;
-				dma-names = "rx", "tx";
-				status = "disabled";
-			};
-
-			usp3: usp@11001000 {
-				compatible = "sirf,atlas7-bt-usp",
-					   "sirf,prima2-usp-pcm";
-				cell-index = <3>;
-				reg = <0x11001000 0x1000>;
-				fifosize = <512>;
-				clocks = <&car 132>, <&car 129>, <&car 133>,
-					<&car 134>, <&car 135>;
-				clock-names = "usp3_io", "a7ca_btss", "a7ca_io",
-					"noc_btm_io", "thbtm_io";
-				dmas = <&dmac4 0>, <&dmac4 1>;
-				dma-names = "rx", "tx";
-			};
-
-			btm@11010000 {
-				compatible = "sirf,nocfw-btm";
-				reg = <0x11010000 0x3000>;
-			};
-		};
-
-		rtcm {
-			compatible = "arteris, flexnoc", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x18810000 0x18810000 0x3000>,
-				<0x18840000 0x18840000 0x1000>,
-				<0x18890000 0x18890000 0x1000>,
-				<0x188B0000 0x188B0000 0x10000>,
-				<0x188D0000 0x188D0000 0x1000>;
-			rtcm@18810000 {
-				compatible = "sirf,nocfw-rtcm";
-				reg = <0x18810000 0x3000>;
-				interrupts = <0 109 0>;
-			};
-
-			gpio_2: gpio_rtcm@18890000 {
-				#gpio-cells = <2>;
-				#interrupt-cells = <2>;
-				compatible = "sirf,atlas7-gpio";
-				reg = <0x18890000 0x1000>;
-				interrupts = <0 47 0>;
-				gpio-controller;
-				interrupt-controller;
-
-				gpio-banks = <1>;
-				gpio-ranges = <&pinctrl 0 0 0>;
-				gpio-ranges-group-names = "rtc_gpio_grp";
-			};
-
-			rtc-iobg@18840000 {
-				compatible = "sirf,prima2-rtciobg",
-					"sirf-prima2-rtciobg-bus",
-					"simple-bus";
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0x18840000 0x1000>;
-
-				sysrtc@2000 {
-					compatible = "sirf,prima2-sysrtc";
-					reg = <0x2000 0x100>;
-					interrupts = <0 52 0>;
-				};
-				pwrc@3000 {
-					compatible = "sirf,atlas7-pwrc";
-					reg = <0x3000 0x100>;
-				};
-			};
-
-			qspi: flash@188B0000 {
-				cell-index = <0>;
-				compatible = "sirf,atlas7-qspi-nor";
-				reg = <0x188B0000 0x10000>;
-				interrupts = <0 15 0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-			retain@0x188D0000 {
-				compatible = "sirf,atlas7-retain";
-				reg = <0x188D0000 0x1000>;
-			};
-
-		};
-		disp-iobg {
-			/* lcdc0 */
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x13100000 0x13100000 0x20000>,
-				<0x10e10000 0x10e10000 0x10000>,
-				<0x17010000 0x17010000 0x10000>;
-
-			lcd@13100000 {
-				compatible = "sirf,atlas7-lcdc";
-				reg = <0x13100000 0x10000>;
-				interrupts = <0 30 0>;
-				clocks = <&car 79>;
-			};
-			vpp@13110000 {
-				compatible = "sirf,atlas7-vpp";
-				reg = <0x13110000 0x10000>;
-				interrupts = <0 31 0>;
-				clocks = <&car 78>;
-				resets = <&car 29>;
-			};
-			lvds@10e10000 {
-				compatible = "sirf,atlas7-lvdsc";
-				reg = <0x10e10000 0x10000>;
-				interrupts = <0 64 0>;
-				clocks = <&car 54>;
-				resets = <&car 29>;
-			};
-			g2d@17010000 {
-				compatible = "sirf, atlas7-g2d";
-				reg = <0x17010000 0x10000>;
-				interrupts = <0 61 0>;
-				clocks = <&car 104>;
-			};
-
-		};
-
-		graphics-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x12000000 0x12000000 0x1000000>;
-
-			graphics@12000000 {
-				compatible = "powervr,sgx531";
-				reg = <0x12000000 0x1000000>;
-				interrupts = <0 6 0>;
-				clocks = <&car 126>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/axis/Makefile b/arch/arm/boot/dts/axis/Makefile
new file mode 100644
index 000000000000..2cab41451281
--- /dev/null
+++ b/arch/arm/boot/dts/axis/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_ARTPEC6) += \
+	artpec6-devboard.dtb
+dtb-$(CONFIG_MACH_ARTPEC6) += \
+	artpec6-devboard.dtb
diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/axis/artpec6-devboard.dts
index d20d95359b28..042a9cc920c6 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/axis/artpec6-devboard.dts
@@ -1,10 +1,5 @@
-/*
- * Axis ARTPEC-6 development board.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Axis ARTPEC-6 development board.
 
 /dts-v1/;
 #include "artpec6.dtsi"
diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/axis/artpec6.dtsi
index 037157e6c5ee..037157e6c5ee 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/axis/artpec6.dtsi
diff --git a/arch/arm/boot/dts/bcm21664-garnet.dts b/arch/arm/boot/dts/bcm21664-garnet.dts
deleted file mode 100644
index be468f4adc37..000000000000
--- a/arch/arm/boot/dts/bcm21664-garnet.dts
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-
-#include "bcm21664.dtsi"
-
-/ {
-	model = "BCM21664 Garnet board";
-	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>; /* 1 GB */
-	};
-
-	uart@3e000000 {
-		status = "okay";
-	};
-
-	sdio1: sdio@3f180000 {
-		max-frequency = <48000000>;
-		status = "okay";
-	};
-
-	sdio2: sdio@3f190000 {
-		non-removable;
-		max-frequency = <48000000>;
-		status = "okay";
-	};
-
-	sdio4: sdio@3f1b0000 {
-		max-frequency = <48000000>;
-		cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
-		status = "okay";
-	};
-
-	usbotg: usb@3f120000 {
-		status = "okay";
-	};
-
-	usbphy: usb-phy@3f130000 {
-		status = "okay";
-	};
-};
diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
deleted file mode 100644
index 1b5a835f66bd..000000000000
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ /dev/null
@@ -1,140 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-#include "bcm2711.dtsi"
-#include "bcm2835-rpi.dtsi"
-#include "bcm283x-rpi-usb-peripheral.dtsi"
-
-/ {
-	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
-	model = "Raspberry Pi 4 Model B";
-
-	chosen {
-		/* 8250 auxiliary UART instead of pl011 */
-		stdout-path = "serial1:115200n8";
-	};
-
-	/* Will be filled by the bootloader */
-	memory@0 {
-		device_type = "memory";
-		reg = <0 0 0>;
-	};
-
-	aliases {
-		ethernet0 = &genet;
-	};
-
-	leds {
-		act {
-			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
-	};
-
-	sd_io_1v8_reg: sd_io_1v8_reg {
-		compatible = "regulator-gpio";
-		regulator-name = "vdd-sd-io";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-		regulator-settling-time-us = <5000>;
-		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1
-			  3300000 0x0>;
-		status = "okay";
-	};
-};
-
-&firmware {
-	expgpio: gpio {
-		compatible = "raspberrypi,firmware-gpio";
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-line-names = "BT_ON",
-				  "WL_ON",
-				  "PWR_LED_OFF",
-				  "GLOBAL_RESET",
-				  "VDD_SD_IO_SEL",
-				  "CAM_GPIO",
-				  "",
-				  "";
-		status = "okay";
-	};
-};
-
-&pwm1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
-	status = "okay";
-};
-
-/* SDHCI is used to control the SDIO for wireless */
-&sdhci {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio34>;
-	bus-width = <4>;
-	non-removable;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	status = "okay";
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
-};
-
-/* EMMC2 is used to drive the SD card */
-&emmc2 {
-	vqmmc-supply = <&sd_io_1v8_reg>;
-	broken-cd;
-	status = "okay";
-};
-
-&genet {
-	phy-handle = <&phy1>;
-	phy-mode = "rgmii-rxid";
-	status = "okay";
-};
-
-&genet_mdio {
-	phy1: ethernet-phy@1 {
-		/* No PHY interrupt */
-		reg = <0x1>;
-	};
-};
-
-/* uart0 communicates with the BT module */
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
-	uart-has-rtscts;
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		max-speed = <2000000>;
-		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-/* uart1 is mapped to the pin header */
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_gpio14>;
-	status = "okay";
-};
-
-&vchiq {
-	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-};
diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts
deleted file mode 100644
index ead6e9804dbf..000000000000
--- a/arch/arm/boot/dts/bcm28155-ap.dts
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * Copyright (C) 2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-
-#include "bcm11351.dtsi"
-
-/ {
-	model = "BCM28155 AP board";
-	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>; /* 1 GB */
-	};
-
-	uart@3e000000 {
-		status = "okay";
-	};
-
-	i2c@3e016000 {
-		status="okay";
-		clock-frequency = <400000>;
-	};
-
-	i2c@3e017000 {
-		status="okay";
-		clock-frequency = <400000>;
-	};
-
-	i2c@3e018000 {
-		status="okay";
-		clock-frequency = <400000>;
-	};
-
-	i2c@3500d000 {
-		status="okay";
-		clock-frequency = <100000>;
-
-		pmu: pmu@8 {
-			reg = <0x08>;
-		};
-	};
-
-	sdio2: sdio@3f190000 {
-		non-removable;
-		max-frequency = <48000000>;
-		vmmc-supply = <&camldo1_reg>;
-		vqmmc-supply = <&iosr1_reg>;
-		status = "okay";
-	};
-
-	sdio4: sdio@3f1b0000 {
-		max-frequency = <48000000>;
-		cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
-		vmmc-supply = <&sdldo_reg>;
-		vqmmc-supply = <&sdxldo_reg>;
-		status = "okay";
-	};
-
-	pwm: pwm@3e01a000 {
-		status = "okay";
-	};
-
-	usbotg: usb@3f120000 {
-		vusb_d-supply = <&usbldo_reg>;
-		vusb_a-supply = <&iosr1_reg>;
-		status = "okay";
-	};
-
-	usbphy: usb-phy@3f130000 {
-		status = "okay";
-	};
-};
-
-#include "bcm59056.dtsi"
-
-&pmu {
-	compatible = "brcm,bcm59056";
-	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
-	regulators {
-		camldo1_reg: camldo1 {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdldo_reg: sdldo {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		sdxldo_reg: sdxldo {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		usbldo_reg: usbldo {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		iosr1_reg: iosr1 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
deleted file mode 100644
index 53bf4579cc22..000000000000
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ /dev/null
@@ -1,37 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "bcm283x.dtsi"
-#include "bcm2835-common.dtsi"
-
-/ {
-	compatible = "brcm,bcm2835";
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,arm1176jzf-s";
-			reg = <0x0>;
-		};
-	};
-
-	soc {
-		ranges = <0x7e000000 0x20000000 0x02000000>;
-		dma-ranges = <0x40000000 0x00000000 0x20000000>;
-	};
-
-	arm-pmu {
-		compatible = "arm,arm1176-pmu";
-	};
-};
-
-&cpu_thermal {
-	coefficients = <(-538)	407000>;
-};
-
-/* enable thermal sensor with the correct compatible property set */
-&thermal {
-	compatible = "brcm,bcm2835-thermal";
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/bcm4709.dtsi b/arch/arm/boot/dts/bcm4709.dtsi
deleted file mode 100644
index e1bb8661955f..000000000000
--- a/arch/arm/boot/dts/bcm4709.dtsi
+++ /dev/null
@@ -1,11 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
- */
-
-#include "bcm4708.dtsi"
-
-&uart0 {
-	clock-frequency = <125000000>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
deleted file mode 100644
index b47fb0700a1f..000000000000
--- a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
+++ /dev/null
@@ -1,56 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright 2018 Luxul Inc.
- */
-
-/dts-v1/;
-
-#include "bcm47094.dtsi"
-
-/ {
-	compatible = "luxul,xap-1610-v1", "brcm,bcm47094", "brcm,bcm4708";
-	model = "Luxul XAP-1610 V1";
-
-	chosen {
-		bootargs = "earlycon";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x08000000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		status	{
-			label = "bcm53xx:green:status";
-			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "timer";
-		};
-
-		2ghz {
-			label = "bcm53xx:blue:2ghz";
-			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
-		};
-
-		5ghz {
-			label = "bcm53xx:blue:5ghz";
-			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		restart {
-			label = "Reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&spi_nor {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
deleted file mode 100644
index 6d28b7dacd05..000000000000
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
+++ /dev/null
@@ -1,76 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright 2018 Luxul Inc.
- */
-
-/dts-v1/;
-
-#include "bcm47094.dtsi"
-#include "bcm5301x-nand-cs0-bch8.dtsi"
-
-/ {
-	compatible = "luxul,xwr-3150-v1", "brcm,bcm47094", "brcm,bcm4708";
-	model = "Luxul XWR-3150 V1";
-
-	chosen {
-		bootargs = "earlycon";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		power	{
-			label = "bcm53xx:green:power";
-			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "default-on";
-		};
-
-		usb3	{
-			label = "bcm53xx:green:usb3";
-			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
-			trigger-sources = <&ohci_port1>, <&ehci_port1>,
-					  <&xhci_port1>;
-			linux,default-trigger = "usbport";
-		};
-
-		status	{
-			label = "bcm53xx:green:status";
-			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "timer";
-		};
-
-		2ghz {
-			label = "bcm53xx:green:2ghz";
-			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
-		};
-
-		5ghz {
-			label = "bcm53xx:green:5ghz";
-			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		restart {
-			label = "Reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&usb3 {
-	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
-};
-
-&spi_nor {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/broadcom/Makefile b/arch/arm/boot/dts/broadcom/Makefile
new file mode 100644
index 000000000000..7099d9560033
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/Makefile
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: GPL-2.0
+# Enables support for device-tree overlays
+DTC_FLAGS_bcm2835-rpi-b := -@
+DTC_FLAGS_bcm2835-rpi-a := -@
+DTC_FLAGS_bcm2835-rpi-b-rev2 := -@
+DTC_FLAGS_bcm2835-rpi-b-plus := -@
+DTC_FLAGS_bcm2835-rpi-a-plus := -@
+DTC_FLAGS_bcm2835-rpi-cm1-io1 := -@
+DTC_FLAGS_bcm2836-rpi-2-b := -@
+DTC_FLAGS_bcm2837-rpi-3-a-plus := -@
+DTC_FLAGS_bcm2837-rpi-3-b := -@
+DTC_FLAGS_bcm2837-rpi-3-b-plus := -@
+DTC_FLAGS_bcm2837-rpi-cm3-io3 := -@
+DTC_FLAGS_bcm2837-rpi-zero-2-w := -@
+DTC_FLAGS_bcm2711-rpi-400 := -@
+DTC_FLAGS_bcm2711-rpi-4-b := -@
+DTC_FLAGS_bcm2711-rpi-cm4-io := -@
+DTC_FLAGS_bcm2835-rpi-zero := -@
+DTC_FLAGS_bcm2835-rpi-zero-w := -@
+dtb-$(CONFIG_ARCH_BCM2835) += \
+	bcm2835-rpi-b.dtb \
+	bcm2835-rpi-a.dtb \
+	bcm2835-rpi-b-rev2.dtb \
+	bcm2835-rpi-b-plus.dtb \
+	bcm2835-rpi-a-plus.dtb \
+	bcm2835-rpi-cm1-io1.dtb \
+	bcm2836-rpi-2-b.dtb \
+	bcm2837-rpi-3-a-plus.dtb \
+	bcm2837-rpi-3-b.dtb \
+	bcm2837-rpi-3-b-plus.dtb \
+	bcm2837-rpi-cm3-io3.dtb \
+	bcm2837-rpi-zero-2-w.dtb \
+	bcm2711-rpi-400.dtb \
+	bcm2711-rpi-4-b.dtb \
+	bcm2711-rpi-cm4-io.dtb \
+	bcm2835-rpi-zero.dtb \
+	bcm2835-rpi-zero-w.dtb
+dtb-$(CONFIG_ARCH_BCMBCA) += \
+	bcm947622.dtb \
+	bcm963138.dtb \
+	bcm963138dvt.dtb \
+	bcm963148.dtb \
+	bcm963178.dtb \
+	bcm96756.dtb \
+	bcm96846.dtb \
+	bcm96855.dtb \
+	bcm96878.dtb
+dtb-$(CONFIG_ARCH_BCM_5301X) += \
+	bcm4708-asus-rt-ac56u.dtb \
+	bcm4708-asus-rt-ac68u.dtb \
+	bcm4708-buffalo-wzr-1750dhp.dtb \
+	bcm4708-buffalo-wzr-1166dhp.dtb \
+	bcm4708-buffalo-wzr-1166dhp2.dtb \
+	bcm4708-linksys-ea6300-v1.dtb \
+	bcm4708-linksys-ea6500-v2.dtb \
+	bcm4708-luxul-xap-1510.dtb \
+	bcm4708-luxul-xwc-1000.dtb \
+	bcm4708-netgear-r6250.dtb \
+	bcm4708-netgear-r6300-v2.dtb \
+	bcm4708-smartrg-sr400ac.dtb \
+	bcm47081-asus-rt-n18u.dtb \
+	bcm47081-buffalo-wzr-600dhp2.dtb \
+	bcm47081-buffalo-wzr-900dhp.dtb \
+	bcm47081-luxul-xap-1410.dtb \
+	bcm47081-luxul-xwr-1200.dtb \
+	bcm47081-tplink-archer-c5-v2.dtb \
+	bcm4709-asus-rt-ac87u.dtb \
+	bcm4709-buffalo-wxr-1900dhp.dtb \
+	bcm4709-linksys-ea9200.dtb \
+	bcm4709-netgear-r7000.dtb \
+	bcm4709-netgear-r8000.dtb \
+	bcm4709-tplink-archer-c9-v1.dtb \
+	bcm47094-asus-rt-ac3100.dtb \
+	bcm47094-asus-rt-ac88u.dtb \
+	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-dlink-dir-890l.dtb \
+	bcm47094-linksys-panamera.dtb \
+	bcm47094-luxul-abr-4500.dtb \
+	bcm47094-luxul-xap-1610.dtb \
+	bcm47094-luxul-xbr-4500.dtb \
+	bcm47094-luxul-xwc-2000.dtb \
+	bcm47094-luxul-xwr-3100.dtb \
+	bcm47094-luxul-xwr-3150-v1.dtb \
+	bcm47094-netgear-r8500.dtb \
+	bcm47094-phicomm-k3.dtb \
+	bcm53015-meraki-mr26.dtb \
+	bcm53016-dlink-dwl-8610ap.dtb \
+	bcm53016-meraki-mr32.dtb \
+	bcm94708.dtb \
+	bcm94709.dtb \
+	bcm953012er.dtb \
+	bcm953012hr.dtb \
+	bcm953012k.dtb
+dtb-$(CONFIG_ARCH_BCM_53573) += \
+	bcm47189-luxul-xap-1440.dtb \
+	bcm47189-luxul-xap-810.dtb \
+	bcm47189-tenda-ac9.dtb \
+	bcm947189acdbmr.dtb
+dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
+	bcm911360_entphn.dtb \
+	bcm911360k.dtb \
+	bcm958300k.dtb \
+	bcm958305k.dtb
+dtb-$(CONFIG_ARCH_BCM_HR2) += \
+	bcm53340-ubnt-unifi-switch8.dtb
+dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
+	bcm28155-ap.dtb \
+	bcm21664-garnet.dtb \
+	bcm23550-sparrow.dtb
+dtb-$(CONFIG_ARCH_BCM_NSP) += \
+	bcm958522er.dtb \
+	bcm958525er.dtb \
+	bcm958525xmc.dtb \
+	bcm958622hr.dtb \
+	bcm958623hr.dtb \
+	bcm958625-meraki-mx64.dtb \
+	bcm958625-meraki-mx64-a0.dtb \
+	bcm958625-meraki-mx64w.dtb \
+	bcm958625-meraki-mx64w-a0.dtb \
+	bcm958625-meraki-mx65.dtb \
+	bcm958625-meraki-mx65w.dtb \
+	bcm958625hr.dtb \
+	bcm988312hr.dtb \
+	bcm958625k.dtb
+dtb-$(CONFIG_ARCH_BRCMSTB) += \
+	bcm7445-bcm97445svmb.dtb
diff --git a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi b/arch/arm/boot/dts/broadcom/bcm-cygnus-clock.dtsi
index 52f91a12a99a..52f91a12a99a 100644
--- a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-cygnus-clock.dtsi
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/broadcom/bcm-cygnus.dtsi
index 2dac3efc7640..f9f79ed82518 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-cygnus.dtsi
@@ -91,7 +91,7 @@
 			      <0x20100 0x100>;
 		};
 
-		L2: l2-cache@22000 {
+		L2: cache-controller@22000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x22000 0x1000>;
 			cache-unified;
@@ -112,18 +112,18 @@
 			status = "disabled";
 		};
 
-		pcie_phy: phy@301d0a0 {
+		pcie_phy: pcie_phy@301d0a0 {
 			compatible = "brcm,cygnus-pcie-phy";
 			reg = <0x0301d0a0 0x14>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			pcie0_phy: phy@0 {
+			pcie0_phy: pcie-phy@0 {
 				reg = <0>;
 				#phy-cells = <0>;
 			};
 
-			pcie1_phy: phy@1 {
+			pcie1_phy: pcie-phy@1 {
 				reg = <1>;
 				#phy-cells = <0>;
 			};
@@ -174,8 +174,8 @@
 		mdio: mdio@18002000 {
 			compatible = "brcm,iproc-mdio";
 			reg = <0x18002000 0x8>;
-			#size-cells = <1>;
-			#address-cells = <0>;
+			#size-cells = <0>;
+			#address-cells = <1>;
 			status = "disabled";
 
 			gphy0: ethernet-phy@0 {
@@ -234,8 +234,8 @@
 			compatible = "arm,sp805" , "arm,primecell";
 			reg = <0x18009000 0x1000>;
 			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "wdog_clk", "apb_pclk";
 		};
 
 		gpio_ccm: gpio@1800a000 {
@@ -274,8 +274,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges = <0x81000000 0 0	  0x28000000 0 0x00010000
-				  0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+			ranges = <0x81000000 0 0	  0x28000000 0 0x00010000>,
+				 <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
 
 			phys = <&pcie0_phy>;
 			phy-names = "pcie-phy";
@@ -283,7 +283,7 @@
 			status = "disabled";
 
 			msi-parent = <&msi0>;
-			msi0: msi-controller {
+			msi0: msi {
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
@@ -309,8 +309,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges = <0x81000000 0 0	  0x48000000 0 0x00010000
-				  0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+			ranges = <0x81000000 0 0	  0x48000000 0 0x00010000>,
+				 <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
 
 			phys = <&pcie1_phy>;
 			phy-names = "pcie-phy";
@@ -318,7 +318,7 @@
 			status = "disabled";
 
 			msi-parent = <&msi1>;
-			msi1: msi-controller {
+			msi1: msi {
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
@@ -397,8 +397,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_0>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -409,8 +409,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_1>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -421,8 +421,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_2>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -460,7 +460,7 @@
 			status = "disabled";
 		};
 
-		nand: nand@18046000 {
+		nand_controller: nand-controller@18046000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x18046000 0x600>, <0xf8105408 0x600>,
 			      <0x18046f00 0x20>;
@@ -591,7 +591,6 @@
 		adc: adc@180a6000 {
 			compatible = "brcm,iproc-static-adc";
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 			adc-syscon = <&ts_adc_syscon>;
 			clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>;
 			clock-names = "tsc_clk";
diff --git a/arch/arm/boot/dts/bcm-hr2.dtsi b/arch/arm/boot/dts/broadcom/bcm-hr2.dtsi
index 6142c672811e..788a6806191a 100644
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-hr2.dtsi
@@ -54,8 +54,8 @@
 
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
-		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&cpu0>;
 	};
 
@@ -75,7 +75,7 @@
 		timer@20200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x20200 0x100>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&periph_clk>;
 		};
 
@@ -83,7 +83,7 @@
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x20600 0x20>;
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
-						  IRQ_TYPE_LEVEL_HIGH)>;
+						  IRQ_TYPE_EDGE_RISING)>;
 			clocks = <&periph_clk>;
 		};
 
@@ -91,7 +91,7 @@
 			compatible = "arm,cortex-a9-twd-wdt";
 			reg = <0x20620 0x20>;
 			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
-						  IRQ_TYPE_LEVEL_HIGH)>;
+						  IRQ_TYPE_EDGE_RISING)>;
 			clocks = <&periph_clk>;
 		};
 
@@ -104,7 +104,7 @@
 			      <0x20100 0x100>;
 		};
 
-		L2: l2-cache@22000 {
+		L2: cache-controller@22000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x22000 0x1000>;
 			cache-unified;
@@ -179,7 +179,7 @@
 			status = "disabled";
 		};
 
-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x26000 0x600>,
 			      <0x11b408 0x600>,
@@ -217,7 +217,7 @@
 		};
 
 		qspi: spi@27200 {
-			compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
+			compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
 			reg = <0x027200 0x184>,
 			      <0x027000 0x124>,
 			      <0x11c408 0x004>,
@@ -318,7 +318,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi0>;
-		msi0: msi-controller {
+		msi0: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
@@ -354,7 +354,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi1>;
-		msi1: msi-controller {
+		msi1: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/broadcom/bcm-ns.dtsi
index 372dc1eb88a0..d0d5f7e52a91 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-ns.dtsi
@@ -1,11 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Broadcom BCM470X / BCM5301X ARM platform code.
- * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015,
- * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs
- *
  * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de>
- *
- * Licensed under the GNU/GPL. See COPYING for details.
  */
 
 #include <dt-bindings/clock/bcm-nsp.h>
@@ -15,11 +10,18 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
+	interrupt-parent = <&gic>;
 	#address-cells = <1>;
 	#size-cells = <1>;
-	interrupt-parent = <&gic>;
 
-	chipcommonA@18000000 {
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts =
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	chipcommon-a-bus@18000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x18000000 0x00001000>;
 		#address-cells = <1>;
@@ -44,19 +46,12 @@
 		};
 	};
 
-	mpcore@19000000 {
+	mpcore-bus@19000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		a9pll: arm_clk@0 {
-			#clock-cells = <0>;
-			compatible = "brcm,nsp-armpll";
-			clocks = <&osc>;
-			reg = <0x00000 0x1000>;
-		};
-
 		scu@20000 {
 			compatible = "arm,cortex-a9-scu";
 			reg = <0x20000 0x100>;
@@ -77,14 +72,6 @@
 			clocks = <&periph_clk>;
 		};
 
-		watchdog@20620 {
-			compatible = "arm,cortex-a9-twd-wdt";
-			reg = <0x20620 0x20>;
-			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
-						  IRQ_TYPE_EDGE_RISING)>;
-			clocks = <&periph_clk>;
-		};
-
 		gic: interrupt-controller@21000 {
 			compatible = "arm,cortex-a9-gic";
 			#interrupt-cells = <3>;
@@ -105,58 +92,6 @@
 		};
 	};
 
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts =
-			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		osc: oscillator {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <25000000>;
-		};
-
-		iprocmed: iprocmed {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-
-		iprocslow: iprocslow {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
-			clock-div = <4>;
-			clock-mult = <1>;
-		};
-
-		periph_clk: periph_clk {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&a9pll>;
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-	};
-
-	usb2_phy: usb2-phy@1800c000 {
-		compatible = "brcm,ns-usb2-phy";
-		reg = <0x1800c000 0x1000>;
-		reg-names = "dmu";
-		#phy-cells = <0>;
-		clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
-		clock-names = "phy-ref-clk";
-	};
-
 	axi@18000000 {
 		compatible = "brcm,bus-axi";
 		reg = <0x18000000 0x1000>;
@@ -166,7 +101,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0x000fffff 0xffff>;
-		interrupt-map = 
+		interrupt-map =
 			/* ChipCommon */
 			<0x00000000 0 &gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
 
@@ -242,14 +177,29 @@
 
 			gpio-controller;
 			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		pcie0: pcie@12000 {
 			reg = <0x00012000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		pcie1: pcie@13000 {
 			reg = <0x00013000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+		};
+
+		pcie2: pcie@14000 {
+			reg = <0x00014000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		usb2: usb2@21000 {
@@ -261,9 +211,7 @@
 
 			interrupt-parent = <&gic>;
 
-			ehci: ehci@21000 {
-				#usb-cells = <0>;
-
+			ehci: usb@21000 {
 				compatible = "generic-ehci";
 				reg = <0x00021000 0x1000>;
 				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
@@ -283,9 +231,7 @@
 				};
 			};
 
-			ohci: ohci@22000 {
-				#usb-cells = <0>;
-
+			ohci: usb@22000 {
 				compatible = "generic-ohci";
 				reg = <0x00022000 0x1000>;
 				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
@@ -314,9 +260,7 @@
 
 			interrupt-parent = <&gic>;
 
-			xhci: xhci@23000 {
-				#usb-cells = <0>;
-
+			xhci: usb@23000 {
 				compatible = "generic-xhci";
 				reg = <0x00023000 0x1000>;
 				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
@@ -335,14 +279,32 @@
 
 		gmac0: ethernet@24000 {
 			reg = <0x24000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		gmac1: ethernet@25000 {
 			reg = <0x25000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		gmac2: ethernet@26000 {
 			reg = <0x26000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		gmac3: ethernet@27000 {
@@ -350,15 +312,23 @@
 		};
 	};
 
+	pwm: pwm@18002000 {
+		compatible = "brcm,iproc-pwm";
+		reg = <0x18002000 0x28>;
+		clocks = <&osc>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
 	mdio: mdio@18003000 {
 		compatible = "brcm,iproc-mdio";
 		reg = <0x18003000 0x8>;
-		#size-cells = <1>;
-		#address-cells = <0>;
+		#size-cells = <0>;
+		#address-cells = <1>;
 	};
 
-	mdio-bus-mux@18003000 {
-		compatible = "mdio-mux-mmioreg";
+	mdio-mux@18003000 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
 		mdio-parent-bus = <&mdio>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -380,34 +350,100 @@
 		};
 	};
 
-	usb3_dmp: syscon@18105000 {
-		reg = <0x18105000 0x1000>;
+	rng: rng@18004000 {
+		compatible = "brcm,bcm5301x-rng";
+		reg = <0x18004000 0x14>;
 	};
 
-	i2c0: i2c@18009000 {
-		compatible = "brcm,iproc-i2c";
-		reg = <0x18009000 0x50>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clock-frequency = <100000>;
+	srab: ethernet-switch@18007000 {
+		compatible = "brcm,bcm53011-srab", "brcm,bcm5301x-srab";
+		reg = <0x18007000 0x1000>;
+
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+			};
+
+			port@5 {
+				reg = <5>;
+				ethernet = <&gmac0>;
+			};
+
+			port@7 {
+				reg = <7>;
+				ethernet = <&gmac1>;
+			};
+
+			port@8 {
+				reg = <8>;
+				ethernet = <&gmac2>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+
+	uart2: serial@18008000 {
+		compatible = "ns16550a";
+		reg = <0x18008000 0x20>;
+		clocks = <&iprocslow>;
+		interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
 		status = "disabled";
 	};
 
-	dmu@1800c000 {
+	dmu-bus@1800c000 {
 		compatible = "simple-bus";
 		ranges = <0 0x1800c000 0x1000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		cru@100 {
-			compatible = "simple-bus";
+		cru-bus@100 {
+			compatible = "brcm,ns-cru", "simple-mfd";
 			reg = <0x100 0x1a4>;
 			ranges;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			pin-controller@1c0 {
+			usb2_phy: phy@164 {
+				compatible = "brcm,ns-usb2-phy";
+				reg = <0x164 0x4>;
+				brcm,syscon-clkset = <&cru_clkset>;
+				clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
+				clock-names = "phy-ref-clk";
+				#phy-cells = <0>;
+			};
+
+			cru_clkset: syscon@180 {
+				compatible = "brcm,cru-clkset", "syscon";
+				reg = <0x180 0x4>;
+			};
+
+			pinctrl: pinctrl@1c0 {
 				compatible = "brcm,bcm4708-pinmux";
 				reg = <0x1c0 0x24>;
 				reg-names = "cru_gpio_control";
@@ -417,65 +453,32 @@
 					function = "spi";
 				};
 
-				i2c {
+				pinmux_i2c: i2c-pins {
 					groups = "i2c_grp";
 					function = "i2c";
 				};
 
-				pwm {
+				pinmux_pwm: pwm-pins {
 					groups = "pwm0_grp", "pwm1_grp",
 						 "pwm2_grp", "pwm3_grp";
 					function = "pwm";
 				};
 
-				pinmux_uart1: uart1 {
+				pinmux_uart1: uart1-pins {
 					groups = "uart1_grp";
 					function = "uart1";
 				};
 			};
-		};
-	};
-
-	lcpll0: lcpll0@1800c100 {
-		#clock-cells = <1>;
-		compatible = "brcm,nsp-lcpll0";
-		reg = <0x1800c100 0x14>;
-		clocks = <&osc>;
-		clock-output-names = "lcpll0", "pcie_phy", "sdio",
-				     "ddr_phy";
-	};
-
-	genpll: genpll@1800c140 {
-		#clock-cells = <1>;
-		compatible = "brcm,nsp-genpll";
-		reg = <0x1800c140 0x24>;
-		clocks = <&osc>;
-		clock-output-names = "genpll", "phy", "ethernetclk",
-				     "usbclk", "iprocfast", "sata1",
-				     "sata2";
-	};
-
-	thermal: thermal@1800c2c0 {
-		compatible = "brcm,ns-thermal";
-		reg = <0x1800c2c0 0x10>;
-		#thermal-sensor-cells = <0>;
-	};
-
-	srab: srab@18007000 {
-		compatible = "brcm,bcm5301x-srab";
-		reg = <0x18007000 0x1000>;
-
-		status = "disabled";
 
-		/* ports are defined in board DTS */
-	};
-
-	rng: rng@18004000 {
-		compatible = "brcm,bcm5301x-rng";
-		reg = <0x18004000 0x14>;
+			thermal: thermal@2c0 {
+				compatible = "brcm,ns-thermal";
+				reg = <0x2c0 0x10>;
+				#thermal-sensor-cells = <0>;
+			};
+		};
 	};
 
-	nand: nand@18028000 {
+	nand_controller: nand-controller@18028000 {
 		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
 		reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
 		reg-names = "nand", "iproc-idm", "iproc-ext";
@@ -487,43 +490,8 @@
 		brcm,nand-has-wp;
 	};
 
-	spi@18029200 {
-		compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
-		reg = <0x18029200 0x184>,
-		      <0x18029000 0x124>,
-		      <0x1811b408 0x004>,
-		      <0x180293a0 0x01c>;
-		reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
-		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "spi_lr_fullness_reached",
-				  "spi_lr_session_aborted",
-				  "spi_lr_impatient",
-				  "spi_lr_session_done",
-				  "spi_lr_overhead",
-				  "mspi_done",
-				  "mspi_halted";
-		clocks = <&iprocmed>;
-		clock-names = "iprocmed";
-		num-cs = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		spi_nor: spi-nor@0 {
-			compatible = "jedec,spi-nor";
-			reg = <0>;
-			spi-max-frequency = <20000000>;
-			status = "disabled";
-
-			partitions {
-				compatible = "brcm,bcm947xx-cfe-partitions";
-			};
-		};
+	usb3_dmp: syscon@18105000 {
+		reg = <0x18105000 0x1000>;
 	};
 
 	thermal-zones {
@@ -535,9 +503,9 @@
 
 			trips {
 				cpu-crit {
-					temperature	= <125000>;
-					hysteresis	= <0>;
-					type		= "critical";
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
 				};
 			};
 
diff --git a/arch/arm/boot/dts/broadcom/bcm-nsp-ax.dtsi b/arch/arm/boot/dts/broadcom/bcm-nsp-ax.dtsi
new file mode 100644
index 000000000000..f2e941dbab10
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm-nsp-ax.dtsi
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom Northstar Plus Ax stepping-specific bindings.
+ * Notable differences from B0+ are the secondary-boot-reg and
+ * lack of DMA coherency.
+ */
+
+&cpu1 {
+	secondary-boot-reg = <0xffff042c>;
+};
+
+&dma {
+	/delete-property/ dma-coherent;
+};
+
+&sdio {
+	/delete-property/ dma-coherent;
+};
+
+&amac0 {
+	/delete-property/ dma-coherent;
+};
+
+&amac1 {
+	/delete-property/ dma-coherent;
+};
+
+&amac2 {
+	/delete-property/ dma-coherent;
+};
+
+&ehci0 {
+	/delete-property/ dma-coherent;
+};
+
+&mailbox {
+	/delete-property/ dma-coherent;
+};
+
+&xhci {
+	/delete-property/ dma-coherent;
+};
+
+&ehci0 {
+	/delete-property/ dma-coherent;
+};
+
+&ohci0 {
+	/delete-property/ dma-coherent;
+};
+
+&i2c0 {
+	/delete-property/ dma-coherent;
+};
+
+&sata {
+	/delete-property/ dma-coherent;
+};
+
+&pcie0 {
+	/delete-property/ dma-coherent;
+};
+
+&pcie1 {
+	/delete-property/ dma-coherent;
+};
+
+&pcie2 {
+	/delete-property/ dma-coherent;
+};
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/broadcom/bcm-nsp.dtsi
index da6d70f09ef1..9d20ba3b1ffb 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-nsp.dtsi
@@ -72,12 +72,12 @@
 
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
-		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
-	mpcore@19000000 {
+	mpcore-bus@19000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
@@ -122,7 +122,7 @@
 			      <0x20100 0x100>;
 		};
 
-		L2: l2-cache@22000 {
+		L2: cache-controller@22000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x22000 0x1000>;
 			cache-unified;
@@ -166,7 +166,7 @@
 		};
 	};
 
-	axi@18000000 {
+	axi: axi@18000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x18000000 0x0011c40c>;
 		#address-cells = <1>;
@@ -200,7 +200,7 @@
 			status = "disabled";
 		};
 
-		dma@20000 {
+		dma: dma@20000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x20000 0x1000>;
 			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
@@ -215,9 +215,11 @@
 			clocks = <&iprocslow>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
+			dma-coherent;
+			status = "disabled";
 		};
 
-		sdio: sdhci@21000 {
+		sdio: mmc@21000 {
 			compatible = "brcm,sdhci-iproc-cygnus";
 			reg = <0x21000 0x100>;
 			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
@@ -257,17 +259,17 @@
 			status = "disabled";
 		};
 
-		mailbox: mailbox@25000 {
+		mailbox: mailbox@25c00 {
 			compatible = "brcm,iproc-fa2-mbox";
-			reg = <0x25000 0x445>;
-			interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x25c00 0x400>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 			#mbox-cells = <1>;
 			brcm,rx-status-len = <32>;
 			brcm,use-bcm-hdr;
 			dma-coherent;
 		};
 
-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x026000 0x600>,
 			      <0x11b408 0x600>,
@@ -282,7 +284,7 @@
 		};
 
 		qspi: spi@27200 {
-			compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
+			compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
 			reg = <0x027200 0x184>,
 			      <0x027000 0x124>,
 			      <0x11c408 0x004>,
@@ -308,6 +310,7 @@
 			num-cs = <2>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			status = "disabled";
 		};
 
 		xhci: usb@29000 {
@@ -360,13 +363,49 @@
 			status = "disabled";
 		};
 
+		mdio: mdio@32000 {
+			compatible = "brcm,iproc-mdio";
+			reg = <0x32000 0x8>;
+			#size-cells = <0>;
+			#address-cells = <1>;
+		};
+
+		mdio-mux@32000 {
+			compatible = "mdio-mux-mmioreg", "mdio-mux";
+			reg = <0x32000 0x4>;
+			mux-mask = <0x200>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mdio-parent-bus = <&mdio>;
+
+			mdio_int: mdio@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				usb3_phy: usb3-phy@10 {
+					compatible = "brcm,ns-bx-usb3-phy";
+					reg = <0x10>;
+					usb3-dmp-syscon = <&usb3_dmp>;
+					#phy-cells = <0>;
+					status = "disabled";
+				};
+			};
+
+			mdio_ext: mdio@200 {
+				reg = <0x200>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		rng: rng@33000 {
 			compatible = "brcm,bcm-nsp-rng";
 			reg = <0x33000 0x14>;
 		};
 
 		ccbtimer0: timer@34000 {
-			compatible = "arm,sp804";
+			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x34000 0x1000>;
 			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
@@ -375,7 +414,7 @@
 		};
 
 		ccbtimer1: timer@35000 {
-			compatible = "arm,sp804";
+			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x35000 0x1000>;
 			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
@@ -383,12 +422,12 @@
 			clock-names = "apb_pclk";
 		};
 
-		srab: srab@36000 {
+		srab: ethernet-switch@36000 {
 			compatible = "brcm,nsp-srab";
 			reg = <0x36000 0x1000>,
 			      <0x3f308 0x8>,
 			      <0x3f410 0xc>;
-			reg-names = "srab", "mux_config", "sgmii";
+			reg-names = "srab", "mux_config", "sgmii_config";
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
@@ -418,6 +457,10 @@
 			status = "disabled";
 
 			/* ports are defined in board DTS */
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 
 		i2c0: i2c@38000 {
@@ -436,7 +479,7 @@
 			reg = <0x39000 0x1000>;
 			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>, <&iprocslow>;
-			clock-names = "wdogclk", "apb_pclk";
+			clock-names = "wdog_clk", "apb_pclk";
 		};
 
 		lcpll0: lcpll0@3f100 {
@@ -491,7 +534,7 @@
 			};
 		};
 
-		sata: ahci@41000 {
+		sata: sata@41000 {
 			compatible = "brcm,bcm-nsp-ahci";
 			reg-names = "ahci", "top-ctrl";
 			reg = <0x41000 0x1000>, <0x40020 0x1c>;
@@ -514,13 +557,8 @@
 			};
 		};
 
-		usb3_phy: usb3-phy@104000 {
-			compatible = "brcm,ns-bx-usb3-phy";
-			reg = <0x104000 0x1000>,
-			      <0x032000 0x1000>;
-			reg-names = "dmp", "ccb-mii";
-			#phy-cells = <0>;
-			status = "disabled";
+		usb3_dmp: syscon@104000 {
+			reg = <0x104000 0x1000>;
 		};
 	};
 
@@ -549,7 +587,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi0>;
-		msi0: msi-controller {
+		msi0: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
@@ -586,7 +624,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi1>;
-		msi1: msi-controller {
+		msi1: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
@@ -623,7 +661,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi2>;
-		msi2: msi-controller {
+		msi2: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/broadcom/bcm11351.dtsi
index 6197e7d80e3b..53857e572080 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm11351.dtsi
@@ -1,21 +1,10 @@
-/*
- * Copyright (C) 2012-2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2013 Broadcom Corporation
 
+#include <dt-bindings/clock/bcm281xx.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-#include "dt-bindings/clock/bcm281xx.h"
-
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -60,44 +49,44 @@
 		reg = <0x3404c000 0x400>; /* 1 KiB in SRAM */
 	};
 
-	uart@3e000000 {
+	uartb: serial@3e000000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e000000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e001000 {
+	uartb2: serial@3e001000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e001000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB2>;
 		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e002000 {
+	uartb3: serial@3e002000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e002000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e003000 {
+	uartb4: serial@3e003000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e003000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB4>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
 	L2: l2-cache@3ff20000 {
@@ -122,20 +111,19 @@
 	gpio: gpio@35003000 {
 		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
 		reg = <0x35003000 0x800>;
-		interrupts =
-		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 		#gpio-cells = <2>;
 		#interrupt-cells = <2>;
 		gpio-controller;
 		interrupt-controller;
 	};
 
-	sdio1: sdio@3f180000 {
+	sdio1: mmc@3f180000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x10000>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
@@ -143,7 +131,7 @@
 		status = "disabled";
 	};
 
-	sdio2: sdio@3f190000 {
+	sdio2: mmc@3f190000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x10000>;
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -151,7 +139,7 @@
 		status = "disabled";
 	};
 
-	sdio3: sdio@3f1a0000 {
+	sdio3: mmc@3f1a0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x10000>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -159,7 +147,7 @@
 		status = "disabled";
 	};
 
-	sdio4: sdio@3f1b0000 {
+	sdio4: mmc@3f1b0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x10000>;
 		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -172,7 +160,7 @@
 		reg = <0x35004800 0x430>;
 	};
 
-	i2c@3e016000 {
+	bsc1: i2c@3e016000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3e016000 0x80>;
 		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
@@ -182,7 +170,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e017000 {
+	bsc2: i2c@3e017000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3e017000 0x80>;
 		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
@@ -192,7 +180,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e018000 {
+	bsc3: i2c@3e018000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3e018000 0x80>;
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
@@ -202,7 +190,7 @@
 		status = "disabled";
 	};
 
-	i2c@3500d000 {
+	pmu_bsc: i2c@3500d000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3500d000 0x80>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/broadcom/bcm21664-garnet.dts b/arch/arm/boot/dts/broadcom/bcm21664-garnet.dts
new file mode 100644
index 000000000000..8789fae178bf
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm21664-garnet.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm21664.dtsi"
+
+/ {
+	model = "BCM21664 Garnet board";
+	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+};
+
+&sdio1 {
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm21664.dtsi b/arch/arm/boot/dts/broadcom/bcm21664.dtsi
index 3cf66faf3b56..fa73600e883e 100644
--- a/arch/arm/boot/dts/bcm21664.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm21664.dtsi
@@ -1,21 +1,10 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
 
+#include <dt-bindings/clock/bcm21664.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-#include "dt-bindings/clock/bcm21664.h"
-
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -27,7 +16,7 @@
 		bootargs = "console=ttyS0,115200n8";
 	};
 
-       cpus {
+	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -60,37 +49,37 @@
 		reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */
 	};
 
-	uart@3e000000 {
+	uartb: serial@3e000000 {
 		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e000000 0x118>;
 		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e001000 {
+	uartb2: serial@3e001000 {
 		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e001000 0x118>;
 		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
 		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e002000 {
+	uartb3: serial@3e002000 {
 		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e002000 0x118>;
 		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	L2: l2-cache@3ff20000 {
+	L2: cache-controller@3ff20000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x3ff20000 0x1000>;
 		cache-unified;
@@ -112,18 +101,17 @@
 	gpio: gpio@35003000 {
 		compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio";
 		reg = <0x35003000 0x524>;
-		interrupts =
-		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 		#gpio-cells = <2>;
 		#interrupt-cells = <2>;
 		gpio-controller;
 		interrupt-controller;
 	};
 
-	sdio1: sdio@3f180000 {
+	sdio1: mmc@3f180000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x801c>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
@@ -131,7 +119,7 @@
 		status = "disabled";
 	};
 
-	sdio2: sdio@3f190000 {
+	sdio2: mmc@3f190000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x801c>;
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -139,7 +127,7 @@
 		status = "disabled";
 	};
 
-	sdio3: sdio@3f1a0000 {
+	sdio3: mmc@3f1a0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x801c>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -147,7 +135,7 @@
 		status = "disabled";
 	};
 
-	sdio4: sdio@3f1b0000 {
+	sdio4: mmc@3f1b0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x801c>;
 		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -155,7 +143,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e016000 {
+	bsc1: i2c@3e016000 {
 		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
 		reg = <0x3e016000 0x70>;
 		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
@@ -165,7 +153,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e017000 {
+	bsc2: i2c@3e017000 {
 		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
 		reg = <0x3e017000 0x70>;
 		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
@@ -175,7 +163,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e018000 {
+	bsc3: i2c@3e018000 {
 		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
 		reg = <0x3e018000 0x70>;
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
@@ -185,7 +173,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e01c000 {
+	bsc4: i2c@3e01c000 {
 		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
 		reg = <0x3e01c000 0x70>;
 		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
@@ -296,21 +284,21 @@
 		};
 
 		root_ccu: root_ccu@35001000 {
-			compatible = BCM21664_DT_ROOT_CCU_COMPAT;
+			compatible = "brcm,bcm21664-root-ccu";
 			reg = <0x35001000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "frac_1m";
 		};
 
 		aon_ccu: aon_ccu@35002000 {
-			compatible = BCM21664_DT_AON_CCU_COMPAT;
+			compatible = "brcm,bcm21664-aon-ccu";
 			reg = <0x35002000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "hub_timer";
 		};
 
 		master_ccu: master_ccu@3f001000 {
-			compatible = BCM21664_DT_MASTER_CCU_COMPAT;
+			compatible = "brcm,bcm21664-master-ccu";
 			reg = <0x3f001000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "sdio1",
@@ -324,7 +312,7 @@
 		};
 
 		slave_ccu: slave_ccu@3e011000 {
-			compatible = BCM21664_DT_SLAVE_CCU_COMPAT;
+			compatible = "brcm,bcm21664-slave-ccu";
 			reg = <0x3e011000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "uartb",
diff --git a/arch/arm/boot/dts/bcm23550-sparrow.dts b/arch/arm/boot/dts/broadcom/bcm23550-sparrow.dts
index ace77709f468..ace77709f468 100644
--- a/arch/arm/boot/dts/bcm23550-sparrow.dts
+++ b/arch/arm/boot/dts/broadcom/bcm23550-sparrow.dts
diff --git a/arch/arm/boot/dts/bcm23550.dtsi b/arch/arm/boot/dts/broadcom/bcm23550.dtsi
index a36c9b1d23c8..50ebe93d6bd0 100644
--- a/arch/arm/boot/dts/bcm23550.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm23550.dtsi
@@ -30,12 +30,11 @@
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 
+/* BCM23550 and BCM21664 have almost identical clocks */
+#include <dt-bindings/clock/bcm21664.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-/* BCM23550 and BCM21664 have almost identical clocks */
-#include "dt-bindings/clock/bcm21664.h"
-
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -102,11 +101,10 @@
 		gpio: gpio@1003000 {
 			compatible = "brcm,bcm23550-gpio", "brcm,kona-gpio";
 			reg = <0x01003000 0x524>;
-			interrupts =
-			       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 			#gpio-cells = <2>;
 			#interrupt-cells = <2>;
 			gpio-controller;
@@ -130,36 +128,36 @@
 
 		uartb: serial@0 {
 			compatible = "snps,dw-apb-uart";
-			status = "disabled";
 			reg = <0x00000000 0x118>;
 			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
 			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
+			status = "disabled";
 		};
 
 		uartb2: serial@1000 {
 			compatible = "snps,dw-apb-uart";
-			status = "disabled";
 			reg = <0x00001000 0x118>;
 			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
 			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
+			status = "disabled";
 		};
 
 		uartb3: serial@2000 {
 			compatible = "snps,dw-apb-uart";
-			status = "disabled";
 			reg = <0x00002000 0x118>;
 			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
 			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
+			status = "disabled";
 		};
 
 		bsc1: i2c@16000 {
-			compatible = "brcm,kona-i2c";
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
 			reg = <0x00016000 0x70>;
 			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -169,7 +167,7 @@
 		};
 
 		bsc2: i2c@17000 {
-			compatible = "brcm,kona-i2c";
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
 			reg = <0x00017000 0x70>;
 			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -179,7 +177,7 @@
 		};
 
 		bsc3: i2c@18000 {
-			compatible = "brcm,kona-i2c";
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
 			reg = <0x00018000 0x70>;
 			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -189,7 +187,7 @@
 		};
 
 		bsc4: i2c@1c000 {
-			compatible = "brcm,kona-i2c";
+			compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
 			reg = <0x0001c000 0x70>;
 			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -224,7 +222,7 @@
 			status = "disabled";
 		};
 
-		sdio1: sdio@e80000 {
+		sdio1: mmc@e80000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00e80000 0x801c>;
 			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
@@ -232,7 +230,7 @@
 			status = "disabled";
 		};
 
-		sdio2: sdio@e90000 {
+		sdio2: mmc@e90000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00e90000 0x801c>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -240,7 +238,7 @@
 			status = "disabled";
 		};
 
-		sdio3: sdio@ea0000 {
+		sdio3: mmc@ea0000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00ea0000 0x801c>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -248,7 +246,7 @@
 			status = "disabled";
 		};
 
-		sdio4: sdio@eb0000 {
+		sdio4: mmc@eb0000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00eb0000 0x801c>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -372,21 +370,21 @@
 		};
 
 		root_ccu: root_ccu@35001000 {
-			compatible = BCM21664_DT_ROOT_CCU_COMPAT;
+			compatible = "brcm,bcm21664-root-ccu";
 			reg = <0x35001000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "frac_1m";
 		};
 
 		aon_ccu: aon_ccu@35002000 {
-			compatible = BCM21664_DT_AON_CCU_COMPAT;
+			compatible = "brcm,bcm21664-aon-ccu";
 			reg = <0x35002000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "hub_timer";
 		};
 
 		slave_ccu: slave_ccu@3e011000 {
-			compatible = BCM21664_DT_SLAVE_CCU_COMPAT;
+			compatible = "brcm,bcm21664-slave-ccu";
 			reg = <0x3e011000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "uartb",
@@ -399,7 +397,7 @@
 		};
 
 		master_ccu: master_ccu@3f001000 {
-			compatible = BCM21664_DT_MASTER_CCU_COMPAT;
+			compatible = "brcm,bcm21664-master-ccu";
 			reg = <0x3f001000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "sdio1",
diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
new file mode 100644
index 000000000000..d5f8823230db
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-peripheral.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
+	model = "Raspberry Pi 4 Model B";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	sd_io_1v8_reg: regulator-sd-io-1v8 {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: regulator-sd-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",		/*  0 */
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "GLOBAL_RESET",
+			  "VDD_SD_IO_SEL",
+			  "CAM_GPIO",		/*  5 */
+			  "SD_PWR_ON",
+			  "";
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",		/*  0 */
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",		/*  5 */
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",		/* 10 */
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",		/* 15 */
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",		/* 20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",		/* 25 */
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",		/* 30 */
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",		/* 35 */
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",		/* 40 */
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",		/* 45 */
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",		/* 50 */
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",		/* 55 */
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi1 {
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led_pwr: led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
+	status = "okay";
+};
+
+/* EMMC2 is used to drive the SD card */
+&emmc2 {
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	status = "okay";
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
+&pcie0 {
+	pci@0,0 {
+		device_type = "pci";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		reg = <0 0 0 0 0>;
+
+		usb@0,0 {
+			reg = <0 0 0 0 0>;
+			resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>;
+		};
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi-400.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-400.dts
new file mode 100644
index 000000000000..5a2869a18bd5
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-400.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi-4-b.dts"
+
+/ {
+	compatible = "raspberrypi,400", "brcm,bcm2711";
+	model = "Raspberry Pi 400";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&expgpio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "GLOBAL_RESET",
+			  "VDD_SD_IO_SEL",
+			  "GLOBAL_SHUTDOWN",
+			  "SD_PWR_ON",
+			  "SHUTDOWN_REQUEST";
+};
+
+&genet_mdio {
+	clock-frequency = <1950000>;
+};
+
+&led_pwr {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+/delete-node/ &led_act;
+
+&pm {
+	/delete-property/ system-power-controller;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
new file mode 100644
index 000000000000..d7ba02f586d3
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi-cm4.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	model = "Raspberry Pi Compute Module 4 IO Board";
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi1 {
+	status = "okay";
+};
+
+&genet {
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
new file mode 100644
index 000000000000..48e63ab7848c
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-compute-module", "brcm,bcm2711";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	sd_io_1v8_reg: regulator-sd-io-1v8 {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: regulator-sd-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+/* EMMC2 is used to drive the eMMC */
+&emmc2 {
+	bus-width = <8>;
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	/* Even the IP block is limited to 100 MHz
+	 * this provides a throughput gain
+	 */
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&expgpio {
+	gpio-line-names = "BT_ON",
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "ANT1",
+			  "VDD_SD_IO_SEL",
+			  "CAM_GPIO",
+			  "SD_PWR_ON",
+			  "ANT2";
+
+	ant1: ant1-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>;
+		/* internal antenna enabled */
+		output-high;
+		line-name = "ant1";
+	};
+
+	ant2: ant2-hog {
+		gpio-hog;
+		gpios = <7 GPIO_ACTIVE_HIGH>;
+		/* external antenna disabled */
+		output-low;
+		line-name = "ant2";
+	};
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@0 {
+		/* No PHY interrupt */
+		reg = <0x0>;
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
new file mode 100644
index 000000000000..d233a191c139
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+#include <dt-bindings/power/raspberrypi-power.h>
+#include <dt-bindings/reset/raspberrypi,firmware-reset.h>
+
+/ {
+	/* Will be filled by the bootloader */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0>;
+	};
+
+	aliases {
+		emmc2bus = &emmc2bus;
+		ethernet0 = &genet;
+		pcie0 = &pcie0;
+		blconfig = &blconfig;
+	};
+};
+
+&firmware {
+	firmware_clocks: clocks {
+		compatible = "raspberrypi,firmware-clocks";
+		#clock-cells = <1>;
+	};
+
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+
+	reset: reset {
+		compatible = "raspberrypi,firmware-reset";
+		#reset-cells = <1>;
+	};
+};
+
+&hdmi0 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hdmi1 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hvs {
+	clocks = <&firmware_clocks 4>;
+};
+
+&rmem {
+	/*
+	 * RPi4's co-processor will copy the board's bootloader configuration
+	 * into memory for the OS to consume. It'll also update this node with
+	 * its placement information.
+	 */
+	blconfig: nvram@0 {
+		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x0>;
+		no-map;
+		status = "disabled";
+	};
+};
+
+&v3d {
+	clocks = <&firmware_clocks 5>;
+};
+
+&vchiq {
+	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&xhci {
+	power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};
diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
index 961bed832755..22c7f1561344 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
@@ -12,25 +12,24 @@
 
 	interrupt-parent = <&gicv2>;
 
-	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges;
+	vc4: gpu {
+		compatible = "brcm,bcm2711-vc5";
+		status = "disabled";
+	};
 
-		/*
-		 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
-		 * that's not good enough for the BCM2711 as some devices can
-		 * only address the lower 1G of memory (ZONE_DMA).
-		 */
-		linux,cma {
-			compatible = "shared-dma-pool";
-			size = <0x2000000>; /* 32MB */
-			alloc-ranges = <0x0 0x00000000 0x40000000>;
-			reusable;
-			linux,cma-default;
-		};
+	clk_27MHz: clk-27M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <27000000>;
+		clock-output-names = "27MHz-clock";
 	};
 
+	clk_108MHz: clk-108M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <108000000>;
+		clock-output-names = "108MHz-clock";
+	};
 
 	soc {
 		/*
@@ -43,13 +42,13 @@
 			 <0x7c000000  0x0 0xfc000000  0x02000000>,
 			 <0x40000000  0x0 0xff800000  0x00800000>;
 		/* Emulate a contiguous 30-bit address range for DMA */
-		dma-ranges = <0xc0000000  0x0 0x00000000  0x3c000000>;
+		dma-ranges = <0xc0000000  0x0 0x00000000  0x40000000>;
 
 		/*
 		 * This node is the provider for the enable-method for
 		 * bringing up secondary cores.
 		 */
-		local_intc: local_intc@40000000 {
+		local_intc: interrupt-controller@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 		};
@@ -66,7 +65,18 @@
 						 IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
-		dma: dma@7e007000 {
+		avs_monitor: avs-monitor@7d5d2000 {
+			compatible = "brcm,bcm2711-avs-monitor",
+				     "syscon", "simple-mfd";
+			reg = <0x7d5d2000 0xf00>;
+
+			thermal: thermal {
+				compatible = "brcm,bcm2711-thermal";
+				#thermal-sensor-cells = <0>;
+			};
+		};
+
+		dma: dma-controller@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xb00>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
@@ -97,12 +107,13 @@
 		};
 
 		pm: watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt";
 			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x7e100000 0x114>,
 			      <0x7e00a000 0x24>,
 			      <0x7ec11000 0x20>;
+			reg-names = "pm", "asb", "rpivid_asb";
 			clocks = <&clocks BCM2835_CLOCK_V3D>,
 				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
 				 <&clocks BCM2835_CLOCK_H264>,
@@ -112,10 +123,8 @@
 		};
 
 		rng@7e104000 {
-			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
-
-			/* RNG is incompatible with brcm,bcm2835-rng */
-			status = "disabled";
+			compatible = "brcm,bcm2711-rng200";
+			reg = <0x7e104000 0x28>;
 		};
 
 		uart2: serial@7e201400 {
@@ -242,27 +251,185 @@
 			status = "disabled";
 		};
 
+		pixelvalve0: pixelvalve@7e206000 {
+			compatible = "brcm,bcm2711-pixelvalve0";
+			reg = <0x7e206000 0x100>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			compatible = "brcm,bcm2711-pixelvalve1";
+			reg = <0x7e207000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		pixelvalve2: pixelvalve@7e20a000 {
+			compatible = "brcm,bcm2711-pixelvalve2";
+			reg = <0x7e20a000 0x100>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		pwm1: pwm@7e20c800 {
 			compatible = "brcm,bcm2835-pwm";
 			reg = <0x7e20c800 0x28>;
 			clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clock-rates = <10000000>;
-			#pwm-cells = <2>;
+			#pwm-cells = <3>;
 			status = "disabled";
 		};
 
-		emmc2: emmc2@7e340000 {
-			compatible = "brcm,bcm2711-emmc2";
-			reg = <0x7e340000 0x100>;
-			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clocks BCM2711_CLOCK_EMMC2>;
+		pixelvalve4: pixelvalve@7e216000 {
+			compatible = "brcm,bcm2711-pixelvalve4";
+			reg = <0x7e216000 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
-		hvs@7e400000 {
+		hvs: hvs@7e400000 {
+			compatible = "brcm,bcm2711-hvs";
+			reg = <0x7e400000 0x8000>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		pixelvalve3: pixelvalve@7ec12000 {
+			compatible = "brcm,bcm2711-pixelvalve3";
+			reg = <0x7ec12000 0x100>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		vec: vec@7ec13000 {
+			compatible = "brcm,bcm2711-vec";
+			reg = <0x7ec13000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		dvp: clock@7ef00000 {
+			compatible = "brcm,brcm2711-dvp";
+			reg = <0x7ef00000 0x10>;
+			clocks = <&clk_108MHz>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		aon_intr: interrupt-controller@7ef00100 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7ef00100 0x30>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		hdmi0: hdmi@7ef00700 {
+			compatible = "brcm,bcm2711-hdmi0";
+			reg = <0x7ef00700 0x300>,
+			      <0x7ef00300 0x200>,
+			      <0x7ef00f00 0x80>,
+			      <0x7ef00f80 0x80>,
+			      <0x7ef01b00 0x200>,
+			      <0x7ef01f00 0x400>,
+			      <0x7ef00200 0x80>,
+			      <0x7ef04300 0x100>,
+			      <0x7ef20000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			clock-names = "hdmi", "bvb", "audio", "cec";
+			resets = <&dvp 0>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <0>, <1>, <2>,
+				     <3>, <4>, <5>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
+			ddc = <&ddc0>;
+			dmas = <&dma 10>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		ddc0: i2c@7ef04500 {
+			compatible = "brcm,bcm2711-hdmi-i2c";
+			reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>;
+			reg-names = "bsc", "auto-i2c";
+			clock-frequency = <97500>;
+			status = "disabled";
+		};
+
+		hdmi1: hdmi@7ef05700 {
+			compatible = "brcm,bcm2711-hdmi1";
+			reg = <0x7ef05700 0x300>,
+			      <0x7ef05300 0x200>,
+			      <0x7ef05f00 0x80>,
+			      <0x7ef05f80 0x80>,
+			      <0x7ef06b00 0x200>,
+			      <0x7ef06f00 0x400>,
+			      <0x7ef00280 0x80>,
+			      <0x7ef09300 0x100>,
+			      <0x7ef20000 0x100>;
+			reg-names = "hdmi",
+				    "dvp",
+				    "phy",
+				    "rm",
+				    "packet",
+				    "metadata",
+				    "csc",
+				    "cec",
+				    "hd";
+			ddc = <&ddc1>;
+			clock-names = "hdmi", "bvb", "audio", "cec";
+			resets = <&dvp 1>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <8>, <7>, <6>,
+				     <9>, <10>, <11>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
+			dmas = <&dma 17>;
+			dma-names = "audio-rx";
+			status = "disabled";
+		};
+
+		ddc1: i2c@7ef09500 {
+			compatible = "brcm,bcm2711-hdmi-i2c";
+			reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>;
+			reg-names = "bsc", "auto-i2c";
+			clock-frequency = <97500>;
+			status = "disabled";
+		};
+	};
+
+	/*
+	 * emmc2 has different DMA constraints based on SoC revisions. It was
+	 * moved into its own bus, so as for RPi4's firmware to update them.
+	 * The firmware will find whether the emmc2bus alias is defined, and if
+	 * so, it'll edit the dma-ranges property below accordingly.
+	 */
+	emmc2bus: emmc2bus {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7e000000  0x0 0xfe000000  0x01800000>;
+		dma-ranges = <0x0 0xc0000000  0x0 0x00000000  0x40000000>;
+
+		emmc2: mmc@7e340000 {
+			compatible = "brcm,bcm2711-emmc2";
+			reg = <0x0 0x7e340000 0x100>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clocks BCM2711_CLOCK_EMMC2>;
+			status = "disabled";
+		};
 	};
 
 	arm-pmu {
@@ -293,12 +460,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/100095/0003
+		 * /Level-1-Memory-System/About-the-L1-memory-system?lang=en
+		 * Source for d/i-cache-size
+		 * https://www.raspberrypi.com/documentation/computers
+		 * /processors.html#bcm2711
+		 */
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a72";
 			reg = <0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu1: cpu@1 {
@@ -307,6 +488,13 @@
 			reg = <1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu2: cpu@2 {
@@ -315,6 +503,13 @@
 			reg = <2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu3: cpu@3 {
@@ -323,6 +518,29 @@
 			reg = <3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 *  https://developer.arm.com/documentation/100095/0003
+		 *  /Level-2-Memory-System/About-the-L2-memory-system?lang=en
+		 *  Source for d/i-cache-size
+		 *  https://www.raspberrypi.com/documentation/computers
+		 *  /processors.html#bcm2711
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set
+			cache-level = <2>;
 		};
 	};
 
@@ -331,7 +549,42 @@
 		#address-cells = <2>;
 		#size-cells = <1>;
 
-		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>;
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>,
+			 <0x6 0x00000000  0x6 0x00000000  0x40000000>;
+
+		pcie0: pcie@7d500000 {
+			compatible = "brcm,bcm2711-pcie";
+			reg = <0x0 0x7d500000 0x9310>;
+			device_type = "pci";
+			#address-cells = <3>;
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pcie", "msi";
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &gicv2 GIC_SPI 144
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &gicv2 GIC_SPI 145
+							IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &gicv2 GIC_SPI 146
+							IRQ_TYPE_LEVEL_HIGH>;
+			msi-controller;
+			msi-parent = <&pcie0>;
+
+			ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000
+				  0x0 0x04000000>;
+			/*
+			 * The wrapper around the PCIe block has a bug
+			 * preventing it from accessing beyond the first 3GB of
+			 * memory.
+			 */
+			dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000
+				      0x0 0xc0000000>;
+			brcm,enable-ssc;
+		};
 
 		genet: ethernet@7d580000 {
 			compatible = "brcm,bcm2711-genet-v5";
@@ -346,10 +599,35 @@
 				compatible = "brcm,genet-mdio-v5";
 				reg = <0xe14 0x8>;
 				reg-names = "mdio";
-				#address-cells = <0x0>;
-				#size-cells = <0x1>;
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
 			};
 		};
+
+		xhci: usb@7e9c0000 {
+			compatible = "brcm,bcm2711-xhci", "brcm,xhci-brcm-v2";
+			reg = <0x0 0x7e9c0000 0x100000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+			/* DWC2 and this IP block share the same USB PHY,
+			 * enabling both at the same time results in lockups.
+			 * So keep this node disabled and let the bootloader
+			 * decide which interface should be enabled.
+			 */
+			status = "disabled";
+		};
+
+		v3d: gpu@7ec00000 {
+			compatible = "brcm,2711-v3d";
+			reg = <0x0 0x7ec00000 0x4000>,
+			      <0x0 0x7ec04000 0x4000>;
+			reg-names = "hub", "core0";
+
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+			resets = <&pm BCM2835_RESET_V3D>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };
 
@@ -363,6 +641,7 @@
 
 &cpu_thermal {
 	coefficients = <(-487) 410040>;
+	thermal-sensors = <&thermal>;
 };
 
 &dsi0 {
@@ -371,6 +650,7 @@
 
 &dsi1 {
 	interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+	compatible = "brcm,bcm2711-dsi1";
 };
 
 &gpio {
@@ -380,21 +660,23 @@
 		     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
 
-	gpclk0_gpio49: gpclk0_gpio49 {
+	gpio-ranges = <&gpio 0 0 58>;
+
+	gpclk0_gpio49: gpclk0-gpio49 {
 		pin-gpclk {
 			pins = "gpio49";
 			function = "alt1";
 			bias-disable;
 		};
 	};
-	gpclk1_gpio50: gpclk1_gpio50 {
+	gpclk1_gpio50: gpclk1-gpio50 {
 		pin-gpclk {
 			pins = "gpio50";
 			function = "alt1";
 			bias-disable;
 		};
 	};
-	gpclk2_gpio51: gpclk2_gpio51 {
+	gpclk2_gpio51: gpclk2-gpio51 {
 		pin-gpclk {
 			pins = "gpio51";
 			function = "alt1";
@@ -402,7 +684,7 @@
 		};
 	};
 
-	i2c0_gpio46: i2c0_gpio46 {
+	i2c0_gpio46: i2c0-gpio46 {
 		pin-sda {
 			function = "alt0";
 			pins = "gpio46";
@@ -414,7 +696,7 @@
 			bias-disable;
 		};
 	};
-	i2c1_gpio46: i2c1_gpio46 {
+	i2c1_gpio46: i2c1-gpio46 {
 		pin-sda {
 			function = "alt1";
 			pins = "gpio46";
@@ -426,7 +708,7 @@
 			bias-disable;
 		};
 	};
-	i2c3_gpio2: i2c3_gpio2 {
+	i2c3_gpio2: i2c3-gpio2 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio2";
@@ -438,7 +720,7 @@
 			bias-disable;
 		};
 	};
-	i2c3_gpio4: i2c3_gpio4 {
+	i2c3_gpio4: i2c3-gpio4 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio4";
@@ -450,7 +732,7 @@
 			bias-disable;
 		};
 	};
-	i2c4_gpio6: i2c4_gpio6 {
+	i2c4_gpio6: i2c4-gpio6 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio6";
@@ -462,7 +744,7 @@
 			bias-disable;
 		};
 	};
-	i2c4_gpio8: i2c4_gpio8 {
+	i2c4_gpio8: i2c4-gpio8 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio8";
@@ -474,7 +756,7 @@
 			bias-disable;
 		};
 	};
-	i2c5_gpio10: i2c5_gpio10 {
+	i2c5_gpio10: i2c5-gpio10 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio10";
@@ -486,7 +768,7 @@
 			bias-disable;
 		};
 	};
-	i2c5_gpio12: i2c5_gpio12 {
+	i2c5_gpio12: i2c5-gpio12 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio12";
@@ -498,7 +780,7 @@
 			bias-disable;
 		};
 	};
-	i2c6_gpio0: i2c6_gpio0 {
+	i2c6_gpio0: i2c6-gpio0 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio0";
@@ -510,7 +792,7 @@
 			bias-disable;
 		};
 	};
-	i2c6_gpio22: i2c6_gpio22 {
+	i2c6_gpio22: i2c6-gpio22 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio22";
@@ -522,7 +804,7 @@
 			bias-disable;
 		};
 	};
-	i2c_slave_gpio8: i2c_slave_gpio8 {
+	i2c_slave_gpio8: i2c-slave-gpio8 {
 		pins-i2c-slave {
 			pins = "gpio8",
 			       "gpio9",
@@ -532,7 +814,7 @@
 		};
 	};
 
-	jtag_gpio48: jtag_gpio48 {
+	jtag_gpio48: jtag-gpio48 {
 		pins-jtag {
 			pins = "gpio48",
 			       "gpio49",
@@ -544,7 +826,7 @@
 		};
 	};
 
-	mii_gpio28: mii_gpio28 {
+	mii_gpio28: mii-gpio28 {
 		pins-mii {
 			pins = "gpio28",
 			       "gpio29",
@@ -553,7 +835,7 @@
 			function = "alt4";
 		};
 	};
-	mii_gpio36: mii_gpio36 {
+	mii_gpio36: mii-gpio36 {
 		pins-mii {
 			pins = "gpio36",
 			       "gpio37",
@@ -563,7 +845,7 @@
 		};
 	};
 
-	pcm_gpio50: pcm_gpio50 {
+	pcm_gpio50: pcm-gpio50 {
 		pins-pcm {
 			pins = "gpio50",
 			       "gpio51",
@@ -573,63 +855,63 @@
 		};
 	};
 
-	pwm0_0_gpio12: pwm0_0_gpio12 {
+	pwm0_0_gpio12: pwm0-0-gpio12 {
 		pin-pwm {
 			pins = "gpio12";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_0_gpio18: pwm0_0_gpio18 {
+	pwm0_0_gpio18: pwm0-0-gpio18 {
 		pin-pwm {
 			pins = "gpio18";
 			function = "alt5";
 			bias-disable;
 		};
 	};
-	pwm1_0_gpio40: pwm1_0_gpio40 {
+	pwm1_0_gpio40: pwm1-0-gpio40 {
 		pin-pwm {
 			pins = "gpio40";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio13: pwm0_1_gpio13 {
+	pwm0_1_gpio13: pwm0-1-gpio13 {
 		pin-pwm {
 			pins = "gpio13";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio19: pwm0_1_gpio19 {
+	pwm0_1_gpio19: pwm0-1-gpio19 {
 		pin-pwm {
 			pins = "gpio19";
 			function = "alt5";
 			bias-disable;
 		};
 	};
-	pwm1_1_gpio41: pwm1_1_gpio41 {
+	pwm1_1_gpio41: pwm1-1-gpio41 {
 		pin-pwm {
 			pins = "gpio41";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio45: pwm0_1_gpio45 {
+	pwm0_1_gpio45: pwm0-1-gpio45 {
 		pin-pwm {
 			pins = "gpio45";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_0_gpio52: pwm0_0_gpio52 {
+	pwm0_0_gpio52: pwm0-0-gpio52 {
 		pin-pwm {
 			pins = "gpio52";
 			function = "alt1";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio53: pwm0_1_gpio53 {
+	pwm0_1_gpio53: pwm0-1-gpio53 {
 		pin-pwm {
 			pins = "gpio53";
 			function = "alt1";
@@ -637,7 +919,7 @@
 		};
 	};
 
-	rgmii_gpio35: rgmii_gpio35 {
+	rgmii_gpio35: rgmii-gpio35 {
 		pin-start-stop {
 			pins = "gpio35";
 			function = "alt4";
@@ -647,26 +929,26 @@
 			function = "alt4";
 		};
 	};
-	rgmii_irq_gpio34: rgmii_irq_gpio34 {
+	rgmii_irq_gpio34: rgmii-irq-gpio34 {
 		pin-irq {
 			pins = "gpio34";
 			function = "alt5";
 		};
 	};
-	rgmii_irq_gpio39: rgmii_irq_gpio39 {
+	rgmii_irq_gpio39: rgmii-irq-gpio39 {
 		pin-irq {
 			pins = "gpio39";
 			function = "alt4";
 		};
 	};
-	rgmii_mdio_gpio28: rgmii_mdio_gpio28 {
+	rgmii_mdio_gpio28: rgmii-mdio-gpio28 {
 		pins-mdio {
 			pins = "gpio28",
 			       "gpio29";
 			function = "alt5";
 		};
 	};
-	rgmii_mdio_gpio37: rgmii_mdio_gpio37 {
+	rgmii_mdio_gpio37: rgmii-mdio-gpio37 {
 		pins-mdio {
 			pins = "gpio37",
 			       "gpio38";
@@ -674,7 +956,7 @@
 		};
 	};
 
-	spi0_gpio46: spi0_gpio46 {
+	spi0_gpio46: spi0-gpio46 {
 		pins-spi {
 			pins = "gpio46",
 			       "gpio47",
@@ -683,7 +965,7 @@
 			function = "alt2";
 		};
 	};
-	spi2_gpio46: spi2_gpio46 {
+	spi2_gpio46: spi2-gpio46 {
 		pins-spi {
 			pins = "gpio46",
 			       "gpio47",
@@ -693,7 +975,7 @@
 			function = "alt5";
 		};
 	};
-	spi3_gpio0: spi3_gpio0 {
+	spi3_gpio0: spi3-gpio0 {
 		pins-spi {
 			pins = "gpio0",
 			       "gpio1",
@@ -702,7 +984,7 @@
 			function = "alt3";
 		};
 	};
-	spi4_gpio4: spi4_gpio4 {
+	spi4_gpio4: spi4-gpio4 {
 		pins-spi {
 			pins = "gpio4",
 			       "gpio5",
@@ -711,7 +993,7 @@
 			function = "alt3";
 		};
 	};
-	spi5_gpio12: spi5_gpio12 {
+	spi5_gpio12: spi5-gpio12 {
 		pins-spi {
 			pins = "gpio12",
 			       "gpio13",
@@ -720,7 +1002,7 @@
 			function = "alt3";
 		};
 	};
-	spi6_gpio18: spi6_gpio18 {
+	spi6_gpio18: spi6-gpio18 {
 		pins-spi {
 			pins = "gpio18",
 			       "gpio19",
@@ -730,7 +1012,7 @@
 		};
 	};
 
-	uart2_gpio0: uart2_gpio0 {
+	uart2_gpio0: uart2-gpio0 {
 		pin-tx {
 			pins = "gpio0";
 			function = "alt4";
@@ -742,7 +1024,7 @@
 			bias-pull-up;
 		};
 	};
-	uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 {
+	uart2_ctsrts_gpio2: uart2-ctsrts-gpio2 {
 		pin-cts {
 			pins = "gpio2";
 			function = "alt4";
@@ -754,7 +1036,7 @@
 			bias-disable;
 		};
 	};
-	uart3_gpio4: uart3_gpio4 {
+	uart3_gpio4: uart3-gpio4 {
 		pin-tx {
 			pins = "gpio4";
 			function = "alt4";
@@ -766,7 +1048,7 @@
 			bias-pull-up;
 		};
 	};
-	uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 {
+	uart3_ctsrts_gpio6: uart3-ctsrts-gpio6 {
 		pin-cts {
 			pins = "gpio6";
 			function = "alt4";
@@ -778,7 +1060,7 @@
 			bias-disable;
 		};
 	};
-	uart4_gpio8: uart4_gpio8 {
+	uart4_gpio8: uart4-gpio8 {
 		pin-tx {
 			pins = "gpio8";
 			function = "alt4";
@@ -790,7 +1072,7 @@
 			bias-pull-up;
 		};
 	};
-	uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 {
+	uart4_ctsrts_gpio10: uart4-ctsrts-gpio10 {
 		pin-cts {
 			pins = "gpio10";
 			function = "alt4";
@@ -802,7 +1084,7 @@
 			bias-disable;
 		};
 	};
-	uart5_gpio12: uart5_gpio12 {
+	uart5_gpio12: uart5-gpio12 {
 		pin-tx {
 			pins = "gpio12";
 			function = "alt4";
@@ -814,7 +1096,7 @@
 			bias-pull-up;
 		};
 	};
-	uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 {
+	uart5_ctsrts_gpio14: uart5-ctsrts-gpio14 {
 		pin-cts {
 			pins = "gpio14";
 			function = "alt4";
@@ -828,6 +1110,19 @@
 	};
 };
 
+&rmem {
+	#address-cells = <2>;
+};
+
+&cma {
+	/*
+	 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
+	 * that's not good enough for the BCM2711 as some devices can
+	 * only address the lower 1G of memory (ZONE_DMA).
+	 */
+	alloc-ranges = <0x0 0x00000000 0x40000000>;
+};
+
 &i2c0 {
 	compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
 	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
@@ -886,5 +1181,6 @@
 };
 
 &vec {
+	compatible = "brcm,bcm2711-vec";
 	interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 };
diff --git a/arch/arm/boot/dts/broadcom/bcm28155-ap.dts b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
new file mode 100644
index 000000000000..2f3634545e64
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Broadcom Corporation
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm11351.dtsi"
+
+/ {
+	model = "BCM28155 AP board";
+	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+};
+
+&bsc1 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&bsc2 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&bsc3 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&pmu_bsc {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmu: pmu@8 {
+		reg = <0x08>;
+	};
+};
+
+&pwm {
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	vmmc-supply = <&camldo1_reg>;
+	vqmmc-supply = <&iosr1_reg>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&sdldo_reg>;
+	vqmmc-supply = <&sdxldo_reg>;
+	status = "okay";
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	vusb_d-supply = <&usbldo_reg>;
+	vusb_a-supply = <&iosr1_reg>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+#include "bcm59056.dtsi"
+
+&pmu {
+	compatible = "brcm,bcm59056";
+	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+	regulators {
+		camldo1_reg: camldo1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		sdldo_reg: sdldo {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		sdxldo_reg: sdxldo {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		usbldo_reg: usbldo {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		iosr1_reg: iosr1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm2835-common.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
index fe1ab40c7f22..9261b67dbee1 100644
--- a/arch/arm/boot/dts/bcm2835-common.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
@@ -8,7 +8,7 @@
 	interrupt-parent = <&intc>;
 
 	soc {
-		dma: dma@7e007000 {
+		dma: dma-controller@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xf00>;
 			interrupts = <1 16>,
@@ -62,6 +62,7 @@
 			#reset-cells = <1>;
 			reg = <0x7e100000 0x114>,
 			      <0x7e00a000 0x24>;
+			reg-names = "pm", "asb";
 			clocks = <&clocks BCM2835_CLOCK_V3D>,
 				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
 				 <&clocks BCM2835_CLOCK_H264>,
@@ -70,6 +71,12 @@
 			system-power-controller;
 		};
 
+		rng@7e104000 {
+			compatible = "brcm,bcm2835-rng";
+			reg = <0x7e104000 0x10>;
+			interrupts = <2 29>;
+		};
+
 		pixelvalve@7e206000 {
 			compatible = "brcm,bcm2835-pixelvalve0";
 			reg = <0x7e206000 0x100>;
@@ -100,6 +107,14 @@
 			status = "okay";
 		};
 
+		vec: vec@7e806000 {
+			compatible = "brcm,bcm2835-vec";
+			reg = <0x7e806000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <2 27>;
+			status = "disabled";
+		};
+
 		pixelvalve@7e807000 {
 			compatible = "brcm,bcm2835-pixelvalve2";
 			reg = <0x7e807000 0x100>;
@@ -124,7 +139,6 @@
 			compatible = "brcm,bcm2835-v3d";
 			reg = <0x7ec00000 0x1000>;
 			interrupts = <1 10>;
-			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
 		};
 
 		vc4: gpu {
@@ -138,41 +152,41 @@
 };
 
 &gpio {
-	i2c_slave_gpio18: i2c_slave_gpio18 {
+	i2c_slave_gpio18: i2c-slave-gpio18 {
 		brcm,pins = <18 19 20 21>;
 		brcm,function = <BCM2835_FSEL_ALT3>;
 	};
 
-	jtag_gpio4: jtag_gpio4 {
+	jtag_gpio4: jtag-gpio4 {
 		brcm,pins = <4 5 6 12 13>;
 		brcm,function = <BCM2835_FSEL_ALT5>;
 	};
 
-	pwm0_gpio12: pwm0_gpio12 {
+	pwm0_gpio12: pwm0-gpio12 {
 		brcm,pins = <12>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm0_gpio18: pwm0_gpio18 {
+	pwm0_gpio18: pwm0-gpio18 {
 		brcm,pins = <18>;
 		brcm,function = <BCM2835_FSEL_ALT5>;
 	};
-	pwm0_gpio40: pwm0_gpio40 {
+	pwm0_gpio40: pwm0-gpio40 {
 		brcm,pins = <40>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm1_gpio13: pwm1_gpio13 {
+	pwm1_gpio13: pwm1-gpio13 {
 		brcm,pins = <13>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm1_gpio19: pwm1_gpio19 {
+	pwm1_gpio19: pwm1-gpio19 {
 		brcm,pins = <19>;
 		brcm,function = <BCM2835_FSEL_ALT5>;
 	};
-	pwm1_gpio41: pwm1_gpio41 {
+	pwm1_gpio41: pwm1-gpio41 {
 		brcm,pins = <41>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm1_gpio45: pwm1_gpio45 {
+	pwm1_gpio45: pwm1-gpio45 {
 		brcm,pins = <45>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
index 6c8ce39833bf..069b48272aa5 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
 / {
@@ -12,19 +14,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
@@ -32,7 +21,6 @@
 	 * This is based on the unreleased schematic for the Model A+.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -67,21 +55,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
 			  "USB_LIMIT", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
@@ -93,6 +81,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -108,6 +97,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
index 17fdd48346ff..2726c00431e8 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
 / {
@@ -12,12 +14,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &gpio {
@@ -26,7 +22,6 @@
 	 * RPI00021 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -42,41 +37,41 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
 			  "GPIO21",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
+			  "", /* GPIO26 */
 			  "CAM_GPIO0",
 			  /* Binary number representing build/revision */
 			  "CONFIG0",
 			  "CONFIG1",
 			  "CONFIG2",
 			  "CONFIG3",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
@@ -88,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
@@ -103,6 +99,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
index b0355c229cdc..c57b999a4520 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,19 +15,6 @@
 		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
@@ -34,7 +23,6 @@
 	 * RPI-BPLUS sheet 1
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -69,21 +57,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
+			  "", /* GPIO30 */
 			  "LAN_RUN", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
 			  "USB_LIMIT", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "ETHCLK", /* GPIO44 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "ETH_CLK", /* GPIO44 */
 			  "PWM1_OUT", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
@@ -95,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -110,6 +99,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
index 33b3b5c02521..ae6d3a9586ab 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,12 +15,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &gpio {
@@ -27,7 +23,6 @@
 	 * RPI00022 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -43,40 +38,40 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
 			  "CAM_GPIO",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
+			  "", /* GPIO26 */
 			  "GPIO27",
 			  "GPIO28",
 			  "GPIO29",
 			  "GPIO30",
 			  "GPIO31",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
@@ -88,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
@@ -103,6 +99,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
index 2b69957e0113..72764be75a79 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,12 +15,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &gpio {
@@ -27,7 +23,6 @@
 	 * RPI00021 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -43,41 +38,40 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
-			  "GPIO21",
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
+			  "CAM_GPIO0",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
-			  "CAM_GPIO0",
-			  /* Binary number representing build/revision */
-			  "CONFIG0",
-			  "CONFIG1",
-			  "CONFIG2",
-			  "CONFIG3",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
@@ -89,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
@@ -98,6 +93,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
index a75c882e6575..3f9d198ac3ab 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
@@ -13,7 +13,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -74,6 +73,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1.dtsi
index 58059c2ce129..750cd76948e3 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1.dtsi
@@ -2,10 +2,12 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 
 / {
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -32,6 +34,10 @@
 	};
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+};
+
 &sdhost {
 	non-removable;
 	vmmc-supply = <&reg_3v3>;
diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi-common.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi-common.dtsi
new file mode 100644
index 000000000000..4e7b4a592da7
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-common.dtsi
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This include file covers the common peripherals and configuration between
+ * bcm2835, bcm2836 and bcm2837 implementations that interact with RPi's
+ * firmware interface.
+ */
+
+#include <dt-bindings/power/raspberrypi-power.h>
+
+&firmware {
+	firmware_clocks: clocks {
+		compatible = "raspberrypi,firmware-clocks";
+		#clock-cells = <1>;
+	};
+};
+
+&hdmi {
+	clocks = <&firmware_clocks 9>,
+		 <&firmware_clocks 13>;
+	clock-names = "pixel", "hdmi";
+};
+
+&v3d {
+	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+};
+
+&vec {
+	clocks = <&firmware_clocks 15>;
+};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
index b75af21069f9..1f0b163e400c 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
@@ -6,7 +6,10 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-otg.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
 
 / {
 	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
@@ -21,17 +24,10 @@
 		/* 8250 auxiliary UART instead of pl011 */
 		stdout-path = "serial1:115200n8";
 	};
+};
 
-	leds {
-		act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
-	};
+&bt {
+	shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
 };
 
 &gpio {
@@ -39,7 +35,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -74,19 +69,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
 			  "CAM_GPIO1", /* GPIO40 */
 			  "WL_ON", /* GPIO41 */
-			  "NC", /* GPIO42 */
+			  "", /* GPIO42 */
 			  "WIFI_CLK", /* GPIO43 */
 			  "CAM_GPIO0", /* GPIO44 */
 			  "BT_ON", /* GPIO45 */
@@ -100,6 +97,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
@@ -109,19 +107,13 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+};
+
 &sdhci {
-	#address-cells = <1>;
-	#size-cells = <0>;
+	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
-	bus-width = <4>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	non-removable;
-	status = "okay";
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
 };
 
 &sdhost {
@@ -134,13 +126,6 @@
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		max-speed = <2000000>;
-		shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
-	};
 };
 
 &uart1 {
@@ -148,3 +133,7 @@
 	pinctrl-0 = <&uart1_gpio14>;
 	status = "okay";
 };
+
+&wifi_pwrseq {
+	reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
index 6dd93c6f4966..539c19c10946 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
@@ -6,6 +6,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-otg.dtsi"
 
 / {
@@ -16,12 +18,6 @@
 		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-	};
 };
 
 &gpio {
@@ -29,7 +25,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -64,22 +59,22 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
-			  "NC", /* GPIO40 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
-			  "NC", /* GPIO45 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED_N",
 			  /* Used by SD Card */
@@ -90,6 +85,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -105,6 +101,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
 &sdhost {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdhost_gpio48>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
index 394c8a71b13b..f0acc9390f31 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
@@ -1,20 +1,14 @@
 #include <dt-bindings/power/raspberrypi-power.h>
 
 / {
-	leds {
-		compatible = "gpio-leds";
-
-		act {
-			label = "ACT";
-			default-state = "keep";
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
 	soc {
 		firmware: firmware {
-			compatible = "raspberrypi,bcm2835-firmware", "simple-bus";
+			compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
 			mboxes = <&mailbox>;
+			dma-ranges;
 		};
 
 		power: power {
@@ -32,8 +26,6 @@
 };
 
 &gpio {
-	pinctrl-names = "default";
-
 	gpioout: gpioout {
 		brcm,pins = <6>;
 		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
diff --git a/arch/arm/boot/dts/broadcom/bcm2835.dtsi b/arch/arm/boot/dts/broadcom/bcm2835.dtsi
new file mode 100644
index 000000000000..15cb331febbb
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2835.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm283x.dtsi"
+#include "bcm2835-common.dtsi"
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,arm1176jzf-s";
+			reg = <0x0>;
+			/* Source for d/i-cache-line-size and d/i-cache-sets
+			 * https://developer.arm.com/documentation/ddi0301
+			 * /h/level-one-memory-system/cache-organization?lang=en
+			 *
+			 * Source for d/i-cache-size
+			 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+			 *
+			 * NOTE: The BCM2835 has a L2 cache but it is dedicated to the GPU
+			 * It can be shared with the CPU through fw settings,
+			 * but this is not recommended.
+			 */
+			d-cache-size = <0x4000>;
+			d-cache-line-size = <16>;
+			d-cache-sets = <256>; // 16KiB(size)/16(line-size)=1024ways/4-way set
+			i-cache-size = <0x4000>;
+			i-cache-line-size = <16>;
+			i-cache-sets = <256>; // 16KiB(size)/16(line-size)=1024ways/4-way set
+		};
+	};
+
+	soc {
+		ranges = <0x7e000000 0x20000000 0x02000000>;
+		dma-ranges = <0x40000000 0x00000000 0x20000000>;
+	};
+
+	arm-pmu {
+		compatible = "arm,arm1176-pmu";
+	};
+};
+
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2835-thermal";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
index 0455a680394a..79918033750e 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include "bcm2836.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,19 +14,6 @@
 		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
@@ -34,7 +22,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -83,7 +70,7 @@
 			  "CAM_GPIO0",
 			  "SMPS_SCL",
 			  "SMPS_SDA",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "PWM1_OUT",
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
@@ -95,6 +82,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -110,6 +98,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2836-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2836-rpi.dtsi
index c4c858b984c6..48b03b55ff56 100644
--- a/arch/arm/boot/dts/bcm2836-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2836-rpi.dtsi
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
 
 &vchiq {
 	compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/broadcom/bcm2836.dtsi
index 82d6c4662ae4..783fe624ba68 100644
--- a/arch/arm/boot/dts/bcm2836.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2836.dtsi
@@ -10,7 +10,7 @@
 			 <0x40000000 0x40000000 0x00001000>;
 		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
 
-		local_intc: local_intc@40000000 {
+		local_intc: interrupt-controller@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 			interrupt-controller;
@@ -40,11 +40,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp";
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0464/f/L1-Memory-System
+		 * /About-the-L1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+		 */
+
 		v7_cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0xf00>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		v7_cpu1: cpu@1 {
@@ -52,6 +67,13 @@
 			compatible = "arm,cortex-a7";
 			reg = <0xf01>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		v7_cpu2: cpu@2 {
@@ -59,6 +81,13 @@
 			compatible = "arm,cortex-a7";
 			reg = <0xf02>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		v7_cpu3: cpu@3 {
@@ -66,6 +95,28 @@
 			compatible = "arm,cortex-a7";
 			reg = <0xf03>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0464/f/L2-Memory-System
+		 * /About-the-L2-Memory-system?lang=en
+		 * Source for cache-size
+		 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 512KiB(size)/64(line-size)=8192ways/8-way set
+			cache-level = <2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
index 66ab35eccba7..3548306dfbcb 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
@@ -2,7 +2,9 @@
 /dts-v1/;
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
 
 / {
 	compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
@@ -17,17 +19,6 @@
 		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
-
-	leds {
-		act {
-			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &firmware {
@@ -52,7 +43,6 @@
 	 * This is mostly based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -122,32 +112,23 @@
 	status = "okay";
 };
 
-&pwm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
-	status = "okay";
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 };
 
-/*
- * SDHCI is used to control the SDIO for wireless
- *
- * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
- * by a single GPIO. We can't give GPIO control to one of the drivers,
- * otherwise the other part would get unexpectedly disturbed.
- */
-&sdhci {
-	#address-cells = <1>;
-	#size-cells = <0>;
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
 	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio34>;
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
 	status = "okay";
-	bus-width = <4>;
-	non-removable;
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
 };
 
 /* SDHOST is used to drive the SD card */
@@ -158,16 +139,15 @@
 	bus-width = <4>;
 };
 
-/* uart0 communicates with the BT module */
+/* uart0 communicates with the BT module
+ *
+ * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
+ * by a single GPIO. We can't give GPIO control to one of the drivers,
+ * otherwise the other part would get unexpectedly disturbed.
+ */
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		max-speed = <2000000>;
-	};
 };
 
 /* uart1 is mapped to the pin header */
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
index 74ed6d047807..2f1800cbc522 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
@@ -3,7 +3,9 @@
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
 
 / {
 	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
@@ -18,22 +20,10 @@
 		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
+};
 
-	leds {
-		act {
-			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
-		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
-	};
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
 };
 
 &firmware {
@@ -43,7 +33,7 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "BT_ON",
 				  "WL_ON",
-				  "STATUS_LED_R",
+				  "PWR_LED_R",
 				  "LAN_RUN",
 				  "",
 				  "CAM_GPIO0",
@@ -59,7 +49,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -108,7 +97,7 @@
 			  "SD1_DATA3",
 			  "PWM0_OUT",
 			  "PWM1_OUT",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "WIFI_CLK",
 			  "SDA0",
 			  "SCL0",
@@ -129,27 +118,23 @@
 	status = "okay";
 };
 
-&pwm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
-	status = "okay";
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
 };
 
-/* SDHCI is used to control the SDIO for wireless */
-&sdhci {
-	#address-cells = <1>;
-	#size-cells = <0>;
+&pwm {
 	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio34>;
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
 	status = "okay";
-	bus-width = <4>;
-	non-removable;
-	mmc-pwrseq = <&wifi_pwrseq>;
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
 };
 
 /* SDHOST is used to drive the SD card */
@@ -164,13 +149,6 @@
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		max-speed = <2000000>;
-		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
-	};
 };
 
 /* uart1 is mapped to the pin header */
@@ -179,3 +157,7 @@
 	pinctrl-0 = <&uart1_gpio14>;
 	status = "okay";
 };
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
index 054ecaa355c9..61270340075c 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
@@ -2,8 +2,10 @@
 /dts-v1/;
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
 
 / {
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
@@ -18,17 +20,10 @@
 		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
+};
 
-	leds {
-		act {
-			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
-	};
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
 };
 
 &firmware {
@@ -54,7 +49,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -103,7 +97,7 @@
 			  "SD1_DATA3",
 			  "PWM0_OUT",
 			  "PWM1_OUT",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "WIFI_CLK",
 			  "SDA0",
 			  "SCL0",
@@ -130,17 +124,14 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
+};
+
 /* uart0 communicates with the BT module */
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		max-speed = <2000000>;
-		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
-	};
 };
 
 /* uart1 is mapped to the pin header */
@@ -150,23 +141,6 @@
 	status = "okay";
 };
 
-/* SDHCI is used to control the SDIO for wireless */
-&sdhci {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio34>;
-	status = "okay";
-	bus-width = <4>;
-	non-removable;
-	mmc-pwrseq = <&wifi_pwrseq>;
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
-};
-
 /* SDHOST is used to drive the SD card */
 &sdhost {
 	pinctrl-names = "default";
@@ -174,3 +148,7 @@
 	status = "okay";
 	bus-width = <4>;
 };
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
index 588d9411ceb6..72d26d130efa 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
@@ -13,7 +13,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -63,8 +62,8 @@
 			  "GPIO43",
 			  "GPIO44",
 			  "GPIO45",
-			  "GPIO46",
-			  "GPIO47",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
 			  /* Used by eMMC */
 			  "SD_CLK_R",
 			  "SD_CMD_R",
@@ -73,6 +72,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3.dtsi
index 925cb37c22f0..1e4e4946b6b6 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3.dtsi
@@ -9,14 +9,6 @@
 		reg = <0 0x40000000>;
 	};
 
-	leds {
-		/*
-		 * Since there is no upstream GPIO driver yet,
-		 * remove the incomplete node.
-		 */
-		/delete-node/ act;
-	};
-
 	reg_3v3: fixed-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3V3";
@@ -41,12 +33,12 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "HDMI_HPD_N",
 				  "EMMC_EN_N",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC";
+				  "",
+				  "",
+				  "",
+				  "",
+				  "",
+				  "";
 		status = "okay";
 	};
 };
diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
new file mode 100644
index 000000000000..85cf594724ef
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-2-w", "brcm,bcm2837";
+	model = "Raspberry Pi Zero 2 W";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&bt {
+	shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "CAM_GPIO0", /* GPIO40 */
+			  "WL_ON", /* GPIO41 */
+			  "BT_ON", /* GPIO42 */
+			  "WIFI_CLK", /* GPIO43 */
+			  "SDA0", /* GPIO44 */
+			  "SCL0", /* GPIO45 */
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+};
+
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/bcm2837.dtsi b/arch/arm/boot/dts/broadcom/bcm2837.dtsi
index 9e95fee78e19..84c08b46519d 100644
--- a/arch/arm/boot/dts/bcm2837.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2837.dtsi
@@ -39,12 +39,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0500/e/level-1-memory-system
+		 * /about-the-l1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://magpi.raspberrypi.com/articles/raspberry-pi-3-specs-benchmarks
+		 */
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
 			reg = <0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu1: cpu@1 {
@@ -53,6 +67,13 @@
 			reg = <1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu2: cpu@2 {
@@ -61,6 +82,13 @@
 			reg = <2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu3: cpu@3 {
@@ -69,6 +97,28 @@
 			reg = <3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0500
+		 * /e/level-2-memory-system/about-the-l2-memory-system?lang=en
+		 * Source for cache-size
+		 * https://datasheets.raspberrypi.com/cm/cm1-and-cm3-datasheet.pdf
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>; // 512KiB(size)/64(line-size)=8192ways/16-way set
+			cache-level = <2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi
index 70bece63f9a7..70bece63f9a7 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi
diff --git a/arch/arm/boot/dts/broadcom/bcm283x-rpi-led-deprecated.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-led-deprecated.dtsi
new file mode 100644
index 000000000000..f83e56de1a72
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-led-deprecated.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	/*
+	 * This file provides the now deprecated ACT LED to the
+	 * Raspberry Pi boards. Please don't include this file
+	 * for new boards!
+	 */
+	leds: leds {
+		compatible = "gpio-leds";
+
+		led_act: led-act {
+			label = "ACT";
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9512.dtsi
index 967e081cb9c2..882b13807075 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9512.dtsi
@@ -12,7 +12,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9514.dtsi
index dc7ae776db5f..4273b90b53cc 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9514.dtsi
@@ -11,7 +11,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi
index 73f4ece8dcd0..73f4ece8dcd0 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-usb-host.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi
diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-otg.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-otg.dtsi
index e2fd9610e125..e2fd9610e125 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-usb-otg.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-otg.dtsi
diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-peripheral.dtsi
index 0ff0e9e25327..0ff0e9e25327 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-peripheral.dtsi
diff --git a/arch/arm/boot/dts/broadcom/bcm283x-rpi-wifi-bt.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-wifi-bt.dtsi
new file mode 100644
index 000000000000..0b64cc19941f
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-wifi-bt.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+	};
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	status = "okay";
+
+	bt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/broadcom/bcm283x.dtsi
index 3caaa57eb6c8..2ca8a2505a4d 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x.dtsi
@@ -30,6 +30,19 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	rmem: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		cma: linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x4000000>; /* 64MB */
+			reusable;
+			linux,cma-default;
+		};
+	};
+
 	thermal-zones {
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <0>;
@@ -37,9 +50,9 @@
 
 			trips {
 				cpu-crit {
-					temperature	= <80000>;
-					hysteresis	= <0>;
-					type		= "critical";
+					temperature = <90000>;
+					hysteresis = <0>;
+					type = "critical";
 				};
 			};
 
@@ -84,12 +97,6 @@
 				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
 		};
 
-		rng@7e104000 {
-			compatible = "brcm,bcm2835-rng";
-			reg = <0x7e104000 0x10>;
-			interrupts = <2 29>;
-		};
-
 		mailbox: mailbox@7e00b880 {
 			compatible = "brcm,bcm2835-mbox";
 			reg = <0x7e00b880 0x40>;
@@ -119,6 +126,8 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
+			gpio-ranges = <&gpio 0 0 54>;
+
 			/* Defines common pin muxing groups
 			 *
 			 * While each pin can have its mux selected
@@ -126,17 +135,17 @@
 			 * groups only make sense to switch to a
 			 * particular function together.
 			 */
-			dpi_gpio0: dpi_gpio0 {
+			dpi_gpio0: dpi-gpio0 {
 				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
 					     12 13 14 15 16 17 18 19
 					     20 21 22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			emmc_gpio22: emmc_gpio22 {
+			emmc_gpio22: emmc-gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
-			emmc_gpio34: emmc_gpio34 {
+			emmc_gpio34: emmc-gpio34 {
 				brcm,pins = <34 35 36 37 38 39>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 				brcm,pull = <BCM2835_PUD_OFF
@@ -146,95 +155,95 @@
 					     BCM2835_PUD_UP
 					     BCM2835_PUD_UP>;
 			};
-			emmc_gpio48: emmc_gpio48 {
+			emmc_gpio48: emmc-gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
 
-			gpclk0_gpio4: gpclk0_gpio4 {
+			gpclk0_gpio4: gpclk0-gpio4 {
 				brcm,pins = <4>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk1_gpio5: gpclk1_gpio5 {
+			gpclk1_gpio5: gpclk1-gpio5 {
 				brcm,pins = <5>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk1_gpio42: gpclk1_gpio42 {
+			gpclk1_gpio42: gpclk1-gpio42 {
 				brcm,pins = <42>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk1_gpio44: gpclk1_gpio44 {
+			gpclk1_gpio44: gpclk1-gpio44 {
 				brcm,pins = <44>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk2_gpio6: gpclk2_gpio6 {
+			gpclk2_gpio6: gpclk2-gpio6 {
 				brcm,pins = <6>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk2_gpio43: gpclk2_gpio43 {
+			gpclk2_gpio43: gpclk2-gpio43 {
 				brcm,pins = <43>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 				brcm,pull = <BCM2835_PUD_OFF>;
 			};
 
-			i2c0_gpio0: i2c0_gpio0 {
+			i2c0_gpio0: i2c0-gpio0 {
 				brcm,pins = <0 1>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c0_gpio28: i2c0_gpio28 {
+			i2c0_gpio28: i2c0-gpio28 {
 				brcm,pins = <28 29>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c0_gpio44: i2c0_gpio44 {
+			i2c0_gpio44: i2c0-gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT1>;
 			};
-			i2c1_gpio2: i2c1_gpio2 {
+			i2c1_gpio2: i2c1-gpio2 {
 				brcm,pins = <2 3>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c1_gpio44: i2c1_gpio44 {
+			i2c1_gpio44: i2c1-gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			jtag_gpio22: jtag_gpio22 {
+			jtag_gpio22: jtag-gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
 			};
 
-			pcm_gpio18: pcm_gpio18 {
+			pcm_gpio18: pcm-gpio18 {
 				brcm,pins = <18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			pcm_gpio28: pcm_gpio28 {
+			pcm_gpio28: pcm-gpio28 {
 				brcm,pins = <28 29 30 31>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			sdhost_gpio48: sdhost_gpio48 {
+			sdhost_gpio48: sdhost-gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
 
-			spi0_gpio7: spi0_gpio7 {
+			spi0_gpio7: spi0-gpio7 {
 				brcm,pins = <7 8 9 10 11>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			spi0_gpio35: spi0_gpio35 {
+			spi0_gpio35: spi0-gpio35 {
 				brcm,pins = <35 36 37 38 39>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			spi1_gpio16: spi1_gpio16 {
+			spi1_gpio16: spi1-gpio16 {
 				brcm,pins = <16 17 18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
 			};
-			spi2_gpio40: spi2_gpio40 {
+			spi2_gpio40: spi2-gpio40 {
 				brcm,pins = <40 41 42 43 44 45>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
 			};
 
-			uart0_gpio14: uart0_gpio14 {
+			uart0_gpio14: uart0-gpio14 {
 				brcm,pins = <14 15>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
@@ -243,50 +252,50 @@
 			 * people often run uart0 on the two pins
 			 * without flow control.
 			 */
-			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+			uart0_ctsrts_gpio16: uart0-ctsrts-gpio16 {
 				brcm,pins = <16 17>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
-			uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
+			uart0_ctsrts_gpio30: uart0-ctsrts-gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 				brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
 			};
-			uart0_gpio32: uart0_gpio32 {
+			uart0_gpio32: uart0-gpio32 {
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 				brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
 			};
-			uart0_gpio36: uart0_gpio36 {
+			uart0_gpio36: uart0-gpio36 {
 				brcm,pins = <36 37>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
+			uart0_ctsrts_gpio38: uart0-ctsrts-gpio38 {
 				brcm,pins = <38 39>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			uart1_gpio14: uart1_gpio14 {
+			uart1_gpio14: uart1-gpio14 {
 				brcm,pins = <14 15>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+			uart1_ctsrts_gpio16: uart1-ctsrts-gpio16 {
 				brcm,pins = <16 17>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_gpio32: uart1_gpio32 {
+			uart1_gpio32: uart1-gpio32 {
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+			uart1_ctsrts_gpio30: uart1-ctsrts-gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_gpio40: uart1_gpio40 {
+			uart1_gpio40: uart1-gpio40 {
 				brcm,pins = <40 41>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+			uart1_ctsrts_gpio42: uart1-ctsrts-gpio42 {
 				brcm,pins = <42 43>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
@@ -343,8 +352,6 @@
 			clocks = <&clocks BCM2835_CLOCK_VPU>,
 				 <&clocks BCM2835_CLOCK_DPI>;
 			clock-names = "core", "pixel";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			status = "disabled";
 		};
 
@@ -365,6 +372,7 @@
 					     "dsi0_ddr2",
 					     "dsi0_ddr";
 
+			status = "disabled";
 		};
 
 		aux: aux@7e215000 {
@@ -408,11 +416,11 @@
 			clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clock-rates = <10000000>;
-			#pwm-cells = <2>;
+			#pwm-cells = <3>;
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7e300000 {
+		sdhci: mmc@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
 			interrupts = <2 30>;
@@ -456,14 +464,6 @@
 			status = "disabled";
 		};
 
-		vec: vec@7e806000 {
-			compatible = "brcm,bcm2835-vec";
-			reg = <0x7e806000 0x1000>;
-			clocks = <&clocks BCM2835_CLOCK_VEC>;
-			interrupts = <2 27>;
-			status = "disabled";
-		};
-
 		usb: usb@7e980000 {
 			compatible = "brcm,bcm2835-usb";
 			reg = <0x7e980000 0x10000>;
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac56u.dts
index 6a96655d8626..c80ac16ad949 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac56u.dts
@@ -21,47 +21,46 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:blue:wan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		lan {
+		led-lan {
 			label = "bcm53xx:blue:lan";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		all {
+		led-all {
 			label = "bcm53xx:blue:all";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -70,19 +69,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac68u.dts
index 3b0029e61b4c..3fe17bd7b86d 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac68u.dts
@@ -21,31 +21,31 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		logo {
+		led-logo {
 			label = "bcm53xx:white:logo";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -54,25 +54,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi
new file mode 100644
index 000000000000..9f9084269ef5
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi
@@ -0,0 +1,193 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1166DHP and WZR-1166DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb {
+			/* label = "bcm53xx:blue:usb"; */
+			function = LED_FUNCTION_USB;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>, <&ohci_port2>,
+					  <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-power0 {
+			/* label = "bcm53xx:red:power"; */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power1 {
+			/* label = "bcm53xx:white:power"; */
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router0 {
+			/*  label = "bcm53xx:blue:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router1 {
+			/* label = "bcm53xx:amber:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan {
+			/* label = "bcm53xx:blue:wan"; */
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wireless0 {
+			/* label = "bcm53xx:blue:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless1 {
+			/* label = "bcm53xx:amber:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		button-sw-ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp.dts
new file mode 100644
index 000000000000..8e506269fa1a
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts
new file mode 100644
index 000000000000..596129027074
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP2
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp2", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP2";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1750dhp.dts
index 90f57bad6b24..95ef6ca7210b 100644
--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1750dhp.dts
@@ -21,15 +21,15 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
 	};
 
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 7 0>;
-		gpio-mosi = <&chipcommon 4 0>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
 		cs-gpios = <&chipcommon 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -49,7 +49,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -58,40 +58,40 @@
 			linux,default-trigger = "usbport";
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:white:power";
 			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router0 {
+		led-router0 {
 			label = "bcm53xx:blue:router";
 			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router1 {
+		led-router1 {
 			label = "bcm53xx:amber:router";
 			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:blue:wan";
 			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wireless0 {
+		led-wireless0 {
 			label = "bcm53xx:blue:wireless";
 			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless1 {
+		led-wireless1 {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -100,33 +100,33 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Commit mode set by switch? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: AP mode */
-		sw_ap {
+		button-sw-ap {
 			label = "AP";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6300-v1.dts
index 41548d6d479a..0ed25bf71f0d 100644
--- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6300-v1.dts
@@ -21,16 +21,21 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x180000>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6500-v2.dts
index cd797b4202ad..0454423fe166 100644
--- a/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6500-v2.dts
@@ -19,19 +19,20 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xap-1510.dts
index e58c8077be1d..72e960c888ac 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xap-1510.dts
@@ -8,7 +8,7 @@
 #include "bcm4708.dtsi"
 
 / {
-	compatible = "luxul,xap-1510v1", "brcm,bcm4708";
+	compatible = "luxul,xap-1510-v1", "brcm,bcm4708";
 	model = "Luxul XAP-1510 V1";
 
 	chosen {
@@ -20,22 +20,30 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -45,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -53,10 +61,37 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
 
-&usb3_phy {
+&srab {
 	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@4 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xwc-1000.dts
index 766db617455b..750e17482371 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xwc-1000.dts
@@ -24,8 +24,16 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
-	nand: nand@18028000 {
-		nandcs@0 {
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	nand_controller: nand-controller@18028000 {
+		nand@0 {
 			partitions {
 				compatible = "fixed-partitions";
 				#address-cells = <1>;
@@ -42,7 +50,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
@@ -52,7 +60,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
@@ -60,10 +68,33 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
 
-&usb3_phy {
+&srab {
 	status = "okay";
+
+	ports {
+		port@4 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6250.dts
index fed75e6ab58c..2bdbc7d18b0e 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6250.dts
@@ -13,40 +13,40 @@
 #include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
-	compatible = "netgear,r6250v1", "brcm,bcm4708";
+	compatible = "netgear,r6250-v1", "brcm,bcm4708";
 	model = "Netgear R6250 V1 (BCM4708)";
 
 	chosen {
 		bootargs = "console=ttyS0,115200 earlycon";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		logo {
+		led-logo {
 			label = "bcm53xx:white:logo";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -54,7 +54,7 @@
 			linux,default-trigger = "usbport";
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:blue:wireless";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
@@ -63,19 +63,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
@@ -94,3 +94,41 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6300-v2.dts
index 79542e18915c..77396730bdd3 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6300-v2.dts
@@ -12,7 +12,7 @@
 #include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
-	compatible = "netgear,r6300v2", "brcm,bcm4708";
+	compatible = "netgear,r6300-v2", "brcm,bcm4708";
 	model = "Netgear R6300 V2 (BCM4708)";
 
 	chosen {
@@ -21,36 +21,36 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		logo {
+		led-logo {
 			label = "bcm53xx:white:logo";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:blue:wireless";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
@@ -59,19 +59,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/broadcom/bcm4708-smartrg-sr400ac.dts
index abd35a518046..b226bef3369c 100644
--- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-smartrg-sr400ac.dts
@@ -21,71 +21,71 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		usb3-white {
+		led-usb3-white {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&xhci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		usb3-green {
+		led-usb3-green {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		status-red {
+		led-status-red {
 			label = "bcm53xx:red:status";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		status-green {
+		led-status-green {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		status-blue {
+		led-status-blue {
 			label = "bcm53xx:blue:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-red {
+		led-wan-red {
 			label = "bcm53xx:red:wan";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
 		};
@@ -94,19 +94,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -122,38 +122,36 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4708.dtsi b/arch/arm/boot/dts/broadcom/bcm4708.dtsi
index 1a19e97a987d..1a19e97a987d 100644
--- a/arch/arm/boot/dts/bcm4708.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm4708.dtsi
diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/broadcom/bcm47081-asus-rt-n18u.dts
index c29950b43a95..3854db0118a9 100644
--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-asus-rt-n18u.dts
@@ -21,37 +21,37 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:blue:wan";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		lan {
+		led-lan {
 			label = "bcm53xx:blue:lan";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -60,13 +60,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-600dhp2.dts
index 4dcec6865469..192b8db5a89c 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-600dhp2.dts
@@ -21,15 +21,15 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 7 0>;
-		gpio-mosi = <&chipcommon 4 0>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
 		cs-gpios = <&chipcommon 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -49,40 +49,40 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		router0 {
+		led-router0 {
 			label = "bcm53xx:green:router";
 			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router1 {
+		led-router1 {
 			label = "bcm53xx:amber:router";
 			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wireless0 {
+		led-wireless0 {
 			label = "bcm53xx:green:wireless";
 			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless1 {
+		led-wireless1 {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -91,26 +91,26 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch device mode? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
@@ -118,6 +118,40 @@
 	};
 };
 
-&usb3_phy {
+&srab {
 	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-900dhp.dts
index 0e349e39f608..7655e4ff2d1c 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-900dhp.dts
@@ -21,15 +21,15 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 7 0>;
-		gpio-mosi = <&chipcommon 4 0>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
 		cs-gpios = <&chipcommon 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -49,45 +49,45 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		router0 {
+		led-router0 {
 			label = "bcm53xx:green:router";
 			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router1 {
+		led-router1 {
 			label = "bcm53xx:amber:router";
 			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wireless0 {
+		led-wireless0 {
 			label = "bcm53xx:green:wireless";
 			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless1 {
+		led-wireless1 {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -96,7 +96,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xap-1410.dts
index b9d95011637d..0198b5f9e4a7 100644
--- a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xap-1410.dts
@@ -8,7 +8,7 @@
 #include "bcm47081.dtsi"
 
 / {
-	compatible = "luxul,xap-1410v1", "brcm,bcm47081", "brcm,bcm4708";
+	compatible = "luxul,xap-1410-v1", "brcm,bcm47081", "brcm,bcm4708";
 	model = "Luxul XAP-1410 V1";
 
 	chosen {
@@ -20,22 +20,30 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -45,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -53,10 +61,33 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
 
-&usb3_phy {
+&srab {
 	status = "okay";
+
+	ports {
+		port@4 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xwr-1200.dts
index 0052e1b24130..73ff1694a4a0 100644
--- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xwr-1200.dts
@@ -9,7 +9,7 @@
 #include "bcm5301x-nand-cs0-bch4.dtsi"
 
 / {
-	compatible = "luxul,xwr-1200v1", "brcm,bcm47081", "brcm,bcm4708";
+	compatible = "luxul,xwr-1200-v1", "brcm,bcm47081", "brcm,bcm4708";
 	model = "Luxul XWR-1200 V1";
 
 	chosen {
@@ -21,65 +21,74 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		lan3 {
+		led-lan3 {
 			label = "bcm53xx:green:lan3";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		lan4 {
+		led-lan4 {
 			label = "bcm53xx:green:lan4";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		lan2 {
+		led-lan2 {
 			label = "bcm53xx:green:lan2";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		usb {
+		led-usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		lan1 {
+		led-lan1 {
 			label = "bcm53xx:green:lan1";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
@@ -89,7 +98,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -101,10 +110,51 @@
 	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
 
-&usb3_phy {
+&srab {
 	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts b/arch/arm/boot/dts/broadcom/bcm47081-tplink-archer-c5-v2.dts
index 01c390ed48ea..b6a5886698b2 100644
--- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-tplink-archer-c5-v2.dts
@@ -23,50 +23,50 @@
 	leds {
 		compatible = "gpio-leds";
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 		};
 
-		lan {
+		led-lan {
 			label = "bcm53xx:green:lan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb2-port1 {
+		led-usb2-port1 {
 			label = "bcm53xx:green:usb2-port1";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan-green {
+		led-wan-green {
 			label = "bcm53xx:green:wan";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:green:wps";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb2-port2 {
+		led-usb2-port2 {
 			label = "bcm53xx:green:usb2-port2";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
@@ -77,13 +77,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
@@ -95,30 +95,15 @@
 	status = "okay";
 
 	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		boot@0 {
-			label = "boot";
-			reg = <0x000000 0x040000>;
-			read-only;
-		};
+		compatible = "tplink,safeloader-partitions";
+		partitions-table-offset = <0xe50000>;
 
-		os-image@100000 {
-			label = "os-image";
-			reg = <0x040000 0x200000>;
+		partition-os-image {
 			compatible = "brcm,trx";
 		};
 
-		rootfs@240000 {
-			label = "rootfs";
-			reg = <0x240000 0xc00000>;
-		};
-
-		nvram@ff0000 {
-			label = "nvram";
-			reg = <0xff0000 0x010000>;
+		partition-file-system {
+			linux,rootfs;
 		};
 	};
 };
@@ -126,7 +111,3 @@
 &usb2 {
 	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 };
-
-&usb3_phy {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/bcm47081.dtsi b/arch/arm/boot/dts/broadcom/bcm47081.dtsi
index ed13af028528..ed13af028528 100644
--- a/arch/arm/boot/dts/bcm47081.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm47081.dtsi
diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac87u.dts
index 8f1e565c3db4..59400217f8c3 100644
--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac87u.dts
@@ -19,27 +19,33 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		et1macaddr: et1macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:red:wan";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
@@ -47,16 +53,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -64,6 +68,11 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et1macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &usb3_phy {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/broadcom/bcm4709-buffalo-wxr-1900dhp.dts
index ce888b1835d1..b7cd2faa30ce 100644
--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-buffalo-wxr-1900dhp.dts
@@ -19,57 +19,57 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router-amber {
+		led-router-amber {
 			label = "bcm53xx:amber:router";
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		router-white {
+		led-router-white {
 			label = "bcm53xx:white:router";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless-amber {
+		led-wireless-amber {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless-white {
+		led-wireless-white {
 			label = "bcm53xx:white:wireless";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
@@ -77,42 +77,40 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power";
 			linux,code = <KEY_POWER>;
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 		};
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Commit mode set by switch? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: AP mode */
-		sw_ap {
+		button-sw-ap {
 			label = "AP";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts b/arch/arm/boot/dts/broadcom/bcm4709-linksys-ea9200.dts
index ed8619b54d69..2ba5adf2b7e7 100644
--- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-linksys-ea9200.dts
@@ -16,24 +16,27 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x180000>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -44,3 +47,41 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r7000.dts
index 1f87993eae1d..24ba8f8f9bf3 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r7000.dts
@@ -19,52 +19,52 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:white:5ghz";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:white:wireless";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
@@ -72,22 +72,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r8000.dts
index 6c6199a53d09..127ca8741220 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r8000.dts
@@ -30,68 +30,68 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz-1 {
+		led-5ghz-1 {
 			label = "bcm53xx:white:5ghz-1";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:white:wireless";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz-2 {
+		led-5ghz-2 {
 			label = "bcm53xx:white:5ghz-2";
 			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
@@ -99,28 +99,26 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
@@ -139,8 +137,10 @@
 		#size-cells = <2>;
 
 		wifi@0,1,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
 			reg = <0x0000 0 0 0 0>;
 			ieee80211-freq-limit = <5735000 5835000>;
+			brcm,ccode-map = "JP-JP-78", "US-Q2-86";
 		};
 	};
 };
@@ -161,6 +161,19 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
+			bridge@1,0 {
+				reg = <0x800 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				wifi@0,0 {
+					compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+					reg = <0x0000 0 0 0 0>;
+					brcm,ccode-map = "JP-JP-78", "US-Q2-86";
+				};
+			};
+
 			bridge@1,2,2 {
 				reg = <0x1000 0 0 0 0>;
 
@@ -168,8 +181,10 @@
 				#size-cells = <2>;
 
 				wifi@1,4,0 {
+					compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
 					reg = <0x0000 0 0 0 0>;
 					ieee80211-freq-limit = <5170000 5730000>;
+					brcm,ccode-map = "JP-JP-78", "US-Q2-86";
 				};
 			};
 		};
@@ -187,3 +202,51 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts b/arch/arm/boot/dts/broadcom/bcm4709-tplink-archer-c9-v1.dts
index f806be5da723..5a8b2b1567e6 100644
--- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-tplink-archer-c9-v1.dts
@@ -15,7 +15,7 @@
 		bootargs = "console=ttyS0,115200 earlycon";
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
@@ -23,27 +23,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		lan {
+		led-lan {
 			label = "bcm53xx:blue:lan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -51,24 +51,24 @@
 			linux,default-trigger = "usbport";
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		wan-blue {
+		led-wan-blue {
 			label = "bcm53xx:blue:wan";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
@@ -77,16 +77,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
@@ -106,30 +104,15 @@
 	status = "okay";
 
 	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		boot@0 {
-			label = "boot";
-			reg = <0x000000 0x040000>;
-			read-only;
-		};
+		compatible = "tplink,safeloader-partitions";
+		partitions-table-offset = <0xe50000>;
 
-		os-image@100000 {
-			label = "os-image";
-			reg = <0x040000 0x200000>;
+		partition-os-image {
 			compatible = "brcm,trx";
 		};
 
-		rootfs@240000 {
-			label = "rootfs";
-			reg = <0x240000 0xc00000>;
-		};
-
-		nvram@ff0000 {
-			label = "nvram";
-			reg = <0xff0000 0x010000>;
+		partition-file-system {
+			linux,rootfs;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094.dtsi b/arch/arm/boot/dts/broadcom/bcm4709.dtsi
index cdc5ff593adb..cba3d910bed8 100644
--- a/arch/arm/boot/dts/bcm47094.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm4709.dtsi
@@ -5,14 +5,11 @@
 
 #include "bcm4708.dtsi"
 
-/ {
-};
-
-&usb3_phy {
-	compatible = "brcm,ns-bx-usb3-phy";
-};
-
 &uart0 {
 	clock-frequency = <125000000>;
 	status = "okay";
 };
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dts b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dts
new file mode 100644
index 000000000000..5f089307cd8c
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094-asus-rt-ac3100.dtsi"
+
+/ {
+	compatible = "asus,rt-ac3100", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC3100";
+
+	nvram@1c080000 {
+		et0macaddr: et0macaddr {
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dtsi b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dtsi
new file mode 100644
index 000000000000..09cefce27fb1
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dtsi
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x00180000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "white:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-red {
+			label = "red:wan";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-lan {
+			label = "white:lan";
+			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb2 {
+			label = "white:usb2";
+			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb3 {
+			label = "white:usb3";
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ehci_port1>, <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wps {
+			label = "white:wps";
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+
+		button-reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wifi {
+			label = "Wi-Fi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+
+		button-led {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			label = "cpu";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x00080000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "nvram";
+			reg = <0x00080000 0x00180000>;
+		};
+
+		partition@200000 {
+			label = "firmware";
+			reg = <0x00200000 0x07e00000>;
+			compatible = "brcm,trx";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac88u.dts b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac88u.dts
new file mode 100644
index 000000000000..fd344b55087e
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac88u.dts
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094-asus-rt-ac3100.dtsi"
+
+/ {
+	compatible = "asus,rt-ac88u", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC88U";
+
+	nvram@1c080000 {
+		et1macaddr: et1macaddr {
+		};
+	};
+
+	switch {
+		compatible = "realtek,rtl8365mb";
+		/* 7 = MDIO (has input reads), 6 = MDC (clock, output only) */
+		mdc-gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		mdio-gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		realtek,disable-leds;
+		dsa,member = <1 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan5";
+				phy-handle = <&ethphy0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan6";
+				phy-handle = <&ethphy1>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan7";
+				phy-handle = <&ethphy2>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan8";
+				phy-handle = <&ethphy3>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "cpu";
+				ethernet = <&sw0_p5>;
+				phy-mode = "rgmii";
+				tx-internal-delay-ps = <2000>;
+				rx-internal-delay-ps = <2100>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+
+		mdio {
+			compatible = "realtek,smi-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+	};
+};
+
+&srab {
+	dsa,member = <0 0>;
+
+	ports {
+		sw0_p5: port@5 {
+			/delete-property/ethernet;
+
+			label = "extsw";
+			phy-mode = "rgmii";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&gmac0 {
+	status = "disabled";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr>;
+	nvmem-cell-names = "mac-address";
+};
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-885l.dts
index 911c65fbf251..c5099defe9f9 100644
--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-885l.dts
@@ -21,18 +21,28 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
-	nand: nand@18028000 {
-		nandcs@0 {
+	nvram@1e3f0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e3f0000 0x10000>;
+
+		et2macaddr: et2macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	nand_controller: nand-controller@18028000 {
+		nand@0 {
 			partitions {
 				compatible = "fixed-partitions";
 				#address-cells = <1>;
 				#size-cells = <1>;
 
 				partition@0 {
+					compatible = "seama";
 					label = "firmware";
 					reg = <0x00000000 0x08000000>;
 				};
@@ -43,28 +53,28 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3-white {
+		led-usb3-white {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -72,12 +82,12 @@
 			linux,default-trigger = "usbport";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:white:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -86,20 +96,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: router / extender */
-		extender {
+		button-extender {
 			label = "Extender";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -111,6 +121,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et2macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -118,3 +133,43 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et2macaddr 3>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-890l.dts b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-890l.dts
new file mode 100644
index 000000000000..3124dfd01b94
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-890l.dts
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device tree for D-Link DIR-890L
+ * D-Link calls this board "WRGAC36"
+ * this router has the same looks and form factor as D-Link DIR-885L.
+ *
+ * Some differences from DIR-885L include a separate USB2 port, separate LEDs
+ * for USB2 and USB3, a separate VCC supply for the USB2 slot and no
+ * router/extender switch is mounted (there is an empty mount point on the
+ * PCB) so this device is a pure router. Also the LAN ports are in the right
+ * order.
+ *
+ * Based on the device tree for DIR-885L
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 Linus Walleij
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch1.dtsi"
+
+/ {
+	compatible = "dlink,dir-890l", "brcm,bcm47094", "brcm,bcm4708";
+	model = "D-Link DIR-890L";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		/*
+		 * LED information is derived from the boot log which
+		 * conveniently lists all the LEDs.
+		 */
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb2-white {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:white:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Called "factory reset" in the vendor dmesg */
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * The flash memory is memory mapped at 0x1e000000-0x1fffffff
+	 * 64KB blocks; total size 2MB, same that can be
+	 * found attached to the spi_nor SPI controller.
+	 */
+	nvram@1e1f0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e1f0000 0x00010000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+};
+
+&gmac2 {
+	/*
+	 * The NVRAM curiously does not contain a MAC address
+	 * for et2 so since that is the only ethernet interface
+	 * actually in use on the platform, we use this et0 MAC
+	 * address for et2.
+	 */
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&nandcs {
+	/* Spansion S34ML01G2, 128MB with 128KB erase blocks */
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/*
+		 * This is called "nflash" in the vendor kernel with
+		 * "upgrade" and "rootfs" (probably using OpenWrt
+		 * splitpart). We call it "firmware" like standard tools
+		 * assume. The CFE loader contains incorrect information
+		 * about TRX partitions, ignore this, there are no TRX
+		 * partitions: this device uses SEAMA.
+		 */
+		firmware@0 {
+			compatible = "seama";
+			label = "firmware";
+			reg = <0x00000000 0x08000000>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+			phy-mode = "rgmii";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
index 0faae8950375..2b5c80d835e9 100644
--- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
@@ -18,26 +18,31 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x100000>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 				label = "WiFi";
 				linux,code = <KEY_RFKILL>;
 				gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 				label = "Reset";
 				linux,code = <KEY_RESTART>;
 				gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -47,19 +52,19 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:green:usb2";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -67,89 +72,70 @@
 			linux,default-trigger = "usbport";
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
 		};
 
-		wifi-disabled {
+		led-wifi-disabled {
 			label = "bcm53xx:amber:wifi-disabled";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wifi-enabled {
+		led-wifi-enabled {
 			label = "bcm53xx:white:wifi-enabled";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar1 {
+		led-bluebar1 {
 			label = "bcm53xx:white:bluebar1";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar2 {
+		led-bluebar2 {
 			label = "bcm53xx:white:bluebar2";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar3 {
+		led-bluebar3 {
 			label = "bcm53xx:white:bluebar3";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 		};
 
-		bluebar4 {
+		led-bluebar4 {
 			label = "bcm53xx:white:bluebar4";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar5 {
+		led-bluebar5 {
 			label = "bcm53xx:white:bluebar5";
 			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar6 {
+		led-bluebar6 {
 			label = "bcm53xx:white:bluebar6";
 			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar7 {
+		led-bluebar7 {
 			label = "bcm53xx:white:bluebar7";
 			gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar8 {
+		led-bluebar8 {
 			label = "bcm53xx:white:bluebar8";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
-	mdio-bus-mux {
-		#address-cells = <1>;
-		#size-cells = <0>;
+	mdio-mux@18003000 {
 
 		/* BIT(9) = 1 => external mdio */
-		mdio_ext: mdio@200 {
+		mdio@200 {
 			reg = <0x200>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-		};
-	};
-
-	mdio-mii-mux {
-		compatible = "mdio-mux-mmioreg";
-		mdio-parent-bus = <&mdio_ext>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x1800c1c0 0x4>;
-
-		/* BIT(6) = mdc, BIT(7) = mdio */
-		mux-mask = <0xc0>;
-
-		mdio-mii@0 {
-			/* Enable MII function */
-			reg = <0x0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 
 			switch@0  {
 				compatible = "brcm,bcm53125";
@@ -159,6 +145,8 @@
 				reset-names = "robo_reset";
 				reg = <0>;
 				dsa,member = <1 0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinmux_mdio>;
 
 				ports {
 					#address-cells = <1>;
@@ -219,33 +207,34 @@
 	dsa,member = <0 0>;
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
+		sw0_p0: port@0 {
+			label = "extsw";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan7";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan4";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan8";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
-		port@8 {
-			reg = <8>;
-			ethernet = <&gmac2>;
+		port@5 {
 			label = "cpu";
+			status = "disabled";
 
 			fixed-link {
 				speed = <1000>;
@@ -253,18 +242,61 @@
 			};
 		};
 
-		sw0_p0: port@0 {
-			reg = <0>;
-			label = "extsw";
+		port@7 {
+			label = "cpu";
+			status = "disabled";
 
 			fixed-link {
 				speed = <1000>;
 				full-duplex;
 			};
 		};
+
+		port@8 {
+			label = "cpu";
+		};
 	};
 };
 
 &usb3_phy {
 	status = "okay";
 };
+
+&nandcs {
+	partitions {
+		compatible = "linksys,ns-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x0000000 0x0080000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "nvram";
+			reg = <0x080000 0x0100000>;
+		};
+
+		partition@180000 {
+			label = "devinfo";
+			reg = <0x0180000 0x080000>;
+		};
+
+		partition@200000 {
+			reg = <0x0200000 0x01d00000>;
+			compatible = "linksys,ns-firmware", "brcm,trx";
+		};
+
+		partition@1f00000 {
+			reg = <0x01f00000 0x01d00000>;
+			compatible = "linksys,ns-firmware", "brcm,trx";
+		};
+
+		partition@5200000 {
+			label = "system";
+			reg = <0x05200000 0x02e00000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-abr-4500.dts
index 50f7cd08cfbb..e374062eb5b7 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-abr-4500.dts
@@ -18,20 +18,29 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -44,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -56,6 +65,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -63,3 +77,43 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 1>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-luxul-xap-1610.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xap-1610.dts
new file mode 100644
index 000000000000..badafa024d24
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xap-1610.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+
+/ {
+	compatible = "luxul,xap-1610-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XAP-1610 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:blue:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-920", "CA-CA-892", "GB-DE-964", "NZ-AU-920", "US-US-825";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-920", "CA-CA-892", "GB-DE-964", "NZ-AU-920", "US-US-825";
+		};
+	};
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@1 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xbr-4500.dts
index bcc420f85b56..cf95af9db1e6 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xbr-4500.dts
@@ -18,20 +18,29 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -44,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -56,6 +65,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -63,3 +77,43 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 1>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwc-2000.dts
index 334325390aed..992c19e1cfa1 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwc-2000.dts
@@ -16,15 +16,24 @@
 		bootargs = "earlycon";
 	};
 
-	memory {
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		status	{
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -33,10 +42,8 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
@@ -48,6 +55,33 @@
 	status = "okay";
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3100.dts
index ac7515423474..4d0ba315a204 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3100.dts
@@ -9,7 +9,7 @@
 #include "bcm5301x-nand-cs0-bch4.dtsi"
 
 / {
-	compatible = "luxul,xwr-3100v1", "brcm,bcm47094", "brcm,bcm4708";
+	compatible = "luxul,xwr-3100-v1", "brcm,bcm47094", "brcm,bcm4708";
 	model = "Luxul XWR-3100 V1";
 
 	chosen {
@@ -18,45 +18,54 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power	{
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		lan3	{
+		led-lan3 {
 			label = "bcm53xx:green:lan3";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		lan4	{
+		led-lan4 {
 			label = "bcm53xx:green:lan4";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		wan	{
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		lan1	{
+		led-lan1 {
 			label = "bcm53xx:green:lan1";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		lan2	{
+		led-lan2 {
 			label = "bcm53xx:green:lan2";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3	{
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -64,18 +73,18 @@
 			linux,default-trigger = "usbport";
 		};
 
-		status	{
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -84,7 +93,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -96,6 +105,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -103,3 +117,43 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3150-v1.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3150-v1.dts
new file mode 100644
index 000000000000..83c429afc297
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3150-v1.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018 Luxul Inc.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "luxul,xwr-3150-v1", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Luxul XWR-3150 V1";
+
+	chosen {
+		bootargs = "earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb3 {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-status {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:green:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:green:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-953", "CA-CA-946", "GB-E0-846", "NZ-AU-953", "US-Q2-930";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-953", "CA-CA-946", "GB-E0-846", "NZ-AU-953", "US-Q2-930";
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/broadcom/bcm47094-netgear-r8500.dts
index f42a1703f4ab..76d562610654 100644
--- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-netgear-r8500.dts
@@ -18,45 +18,45 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz-1 {
+		led-5ghz-1 {
 			label = "bcm53xx:white:5ghz-1";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz-2 {
+		led-5ghz-2 {
 			label = "bcm53xx:white:5ghz-2";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
@@ -65,25 +65,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts b/arch/arm/boot/dts/broadcom/bcm47094-phicomm-k3.dts
index ac3a4483dcb3..bb1bc4e61bc2 100644
--- a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-phicomm-k3.dts
@@ -15,14 +15,14 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000
-		       0x88000000 0x18000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -55,7 +55,7 @@
 			reg = <0x0080000 0x0100000>;
 		};
 
-		partition@180000{
+		partition@180000 {
 			label = "phicomm";
 			reg = <0x0180000 0x0280000>;
 			read-only;
diff --git a/arch/arm/boot/dts/broadcom/bcm47094.dtsi b/arch/arm/boot/dts/broadcom/bcm47094.dtsi
new file mode 100644
index 000000000000..6282363313e1
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094.dtsi
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+#include "bcm4708.dtsi"
+
+/ {
+};
+
+&pinctrl {
+	compatible = "brcm,bcm4709-pinmux";
+
+	pinmux_mdio: mdio-pins {
+		groups = "mdio_grp";
+		function = "mdio";
+	};
+};
+
+&usb3_phy {
+	compatible = "brcm,ns-bx-usb3-phy";
+};
+
+&uart0 {
+	clock-frequency = <125000000>;
+	status = "okay";
+};
+
+&srab {
+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
+};
diff --git a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts
index 57ca1cfaecd8..ac44c745bdf8 100644
--- a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts
@@ -23,13 +23,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wlan {
+		led-wlan {
 			label = "bcm53xx:blue:wlan";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "default-off";
 		};
 
-		system {
+		led-system {
 			label = "bcm53xx:green:system";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -39,10 +38,29 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	/delete-node/ fixed-link;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-810.dts
index 2e1a7e382cb7..fd071da26cfa 100644
--- a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-810.dts
@@ -20,36 +20,34 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
-	leds {
+	leds-0 {
 		compatible = "gpio-leds";
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-off";
 		};
 
-		system {
+		led-system {
 			label = "bcm53xx:green:system";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 		};
 	};
 
-	pcie0_leds {
+	leds-1 {
 		compatible = "gpio-leds";
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-off";
 		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
@@ -83,3 +81,22 @@
 		};
 	};
 };
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	/delete-node/ fixed-link;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts b/arch/arm/boot/dts/broadcom/bcm47189-tenda-ac9.dts
index 049cdfd92706..3ac6cac541ca 100644
--- a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47189-tenda-ac9.dts
@@ -20,37 +20,37 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
-	leds {
+	leds-0 {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		system {
+		led-system {
 			label = "bcm53xx:blue:system";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 		};
 	};
 
-	pcie0_leds {
+	leds-1 {
 		compatible = "gpio-leds";
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
 		};
@@ -59,19 +59,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
@@ -105,3 +105,33 @@
 		};
 	};
 };
+
+&switch {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+		};
+
+		port@1 {
+			label = "lan1";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan3";
+		};
+
+		port@4 {
+			label = "lan4";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47622.dtsi b/arch/arm/boot/dts/broadcom/bcm47622.dtsi
new file mode 100644
index 000000000000..7cd38de118c3
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47622.dtsi
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm47622", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm47622-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm53015-meraki-mr26.dts b/arch/arm/boot/dts/broadcom/bcm53015-meraki-mr26.dts
new file mode 100644
index 000000000000..0bf5106f7012
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm53015-meraki-mr26.dts
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+	model = "Meraki MR26";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <50000000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x200000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x200000 0x200000>;
+			/* empty */
+		};
+
+		partition@400000 {
+			label = "u-boot-backup";
+			reg = <0x400000 0x200000>;
+			/* empty */
+		};
+
+		partition@600000 {
+			label = "u-boot-env-backup";
+			reg = <0x600000 0x200000>;
+			/* empty */
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	ina219@40 {
+		compatible = "ti,ina219"; /* PoE power */
+		reg = <0x40>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* it's empty */
+	};
+};
+
+&thermal {
+	status = "disabled";
+	/* does not work, reads 418 degree Celsius */
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm53016-dlink-dwl-8610ap.dts b/arch/arm/boot/dts/broadcom/bcm53016-dlink-dwl-8610ap.dts
new file mode 100644
index 000000000000..c1f54391746f
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm53016-dlink-dwl-8610ap.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "D-Link DWL-8610AP";
+	compatible = "dlink,dwl-8610ap", "brcm,bcm53016", "brcm,bcm4708";
+
+	memory@0 {
+		device_type = "memory";
+		/* 512 MB RAM in 2 x Macronix D9PSH chips */
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led-diag {
+			/* Actually "diag" unclear what this means */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-wlan-2g {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wlan-5g {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			debounce-interval = <100>;
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			/* This GPIO is actually stored in NVRAM, but it's not gonna change */
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * Flash memory at 0x1e000000-0x1fffffff
+	 * Macronix 32 64KB blocks; total size 2MB, same that can be
+	 * found attached to the spi_nor SPI controller.
+	 */
+	nvram@1e080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e080000 0x00020000>;
+
+		et0macaddr: et0macaddr {
+		};
+
+		et1macaddr: et1macaddr {
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	/* Serial SPI NOR Flash MX 25L1606E */
+	status = "okay";
+};
+
+&nandcs {
+	/*
+	 * Spansion S34ML01G100TFI00 128 MB NAND Flash memory
+	 *
+	 * This ECC is a bit unorthodox but it is what the stock firmware
+	 * is using, so to be able to mount the original partitions
+	 * this is necessary.
+	 */
+	nand-ecc-strength = <5>;
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* This is named nflash1.trx in CFE */
+		trx@0 {
+			label = "firmware";
+			reg = <0x00000000 0x02800000>;
+			compatible = "brcm,trx";
+		};
+
+		/* This is named nflash1.trx2 in CFE */
+		trx2@2800000 {
+			label = "firmware2";
+			reg = <0x02800000 0x02800000>;
+			compatible = "brcm,trx";
+		};
+
+		/* This is named nflash1.rwfs in CFE */
+		free@5000000 {
+			label = "free";
+			reg = <0x05000000 0x03000000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm53016-meraki-mr32.dts b/arch/arm/boot/dts/broadcom/bcm53016-meraki-mr32.dts
new file mode 100644
index 000000000000..25eeacf6a248
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm53016-meraki-mr32.dts
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR32 / Codename: Espresso
+ *
+ * Copyright (C) 2018-2020 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr32", "brcm,bcm53016", "brcm,bcm4708";
+	model = "Meraki MR32";
+
+	chosen {
+		bootargs = " console=ttyS0,115200n8 earlycon";
+	};
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	aliases {
+		serial1 = &uart2;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		sysled3 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+			panic-indicator;
+		};
+		sysled2 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led-0 {
+			/* SYS-LED 1 - Tricolor */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			pwms = <&pwm 0 50000 0>;
+			max-brightness = <255>;
+		};
+
+		led-1 {
+			/* SYS-LED 1 - Tricolor */
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			pwms = <&pwm 1 50000 0>;
+			max-brightness = <255>;
+		};
+
+		led-2 {
+			/* SYS-LED 1 - Tricolor */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			pwms = <&pwm 2 50000 0>;
+			max-brightness = <255>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <62500000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&uart2 {
+	status = "okay";
+	/*
+	 * bluetooth-le {
+	 *	compatible = "brcm,bcm20732";
+	 *	enable-gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
+	 *};
+	 */
+};
+
+&gmac0 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&mac_address>;
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&pwm {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_pwm>;
+};
+
+&nandcs {
+	partitions {
+		/*
+		 * The partition autodetection does not work for this device.
+		 * It will only detect the "nvram" partition with an incorrect size.
+		 *	[    1.721667] 1 bcm47xxpart partitions found on MTD device brcmnand.0
+		 *	[    1.727962] Creating 1 MTD partitions on "brcmnand.0":
+		 *	[    1.733117] 0x000000400000-0x000008000000 : "nvram"
+		 */
+
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x100000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "bootkernel1";
+			reg = <0x100000 0x300000>;
+			read-only;
+		};
+
+		partition@400000 {
+			label = "nvram";
+			reg = <0x400000 0x100000>;
+			read-only;
+		};
+
+		partition@500000 {
+			label = "bootkernel2";
+			reg = <0x500000 0x300000>;
+			read-only;
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	current_sense: ina219@45 {
+		compatible = "ti,ina219";
+		reg = <0x45>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@66 {
+			reg = <0x66 0x6>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch1.dtsi
index c349e8f0afc5..c349e8f0afc5 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch1.dtsi
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch4.dtsi
index 18e25e302b13..18e25e302b13 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch4.dtsi
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch8.dtsi
index c8e56d30bd6f..c8e56d30bd6f 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch8.dtsi
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0.dtsi
index 925a7c9ce5b7..be9a00ff752d 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0.dtsi
@@ -6,8 +6,8 @@
  */
 
 / {
-	nand@18028000 {
-		nandcs: nandcs@0 {
+	nand-controller@18028000 {
+		nandcs: nand@0 {
 			compatible = "brcm,nandcs";
 			reg = <0>;
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/broadcom/bcm5301x.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x.dtsi
new file mode 100644
index 000000000000..f06a178a9240
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm5301x.dtsi
@@ -0,0 +1,136 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015,
+ * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "bcm-ns.dtsi"
+
+/ {
+	mpcore-bus@19000000 {
+		a9pll: arm_clk@0 {
+			#clock-cells = <0>;
+			compatible = "brcm,nsp-armpll";
+			clocks = <&osc>;
+			reg = <0x00000 0x1000>;
+		};
+
+		watchdog@20620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x20620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+		};
+
+		iprocmed: iprocmed {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+
+		iprocslow: iprocslow {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&a9pll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	i2c0: i2c@18009000 {
+		compatible = "brcm,iproc-i2c";
+		reg = <0x18009000 0x50>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <100000>;
+		status = "disabled";
+	};
+
+	dmu-bus@1800c000 {
+		cru-bus@100 {
+			lcpll0: clock-controller@100 {
+				#clock-cells = <1>;
+				compatible = "brcm,nsp-lcpll0";
+				reg = <0x100 0x14>;
+				clocks = <&osc>;
+				clock-output-names = "lcpll0", "pcie_phy",
+						     "sdio", "ddr_phy";
+			};
+
+			genpll: clock-controller@140 {
+				#clock-cells = <1>;
+				compatible = "brcm,nsp-genpll";
+				reg = <0x140 0x24>;
+				clocks = <&osc>;
+				clock-output-names = "genpll", "phy",
+						     "ethernetclk",
+						     "usbclk", "iprocfast",
+						     "sata1", "sata2";
+			};
+		};
+	};
+
+	spi@18029200 {
+		compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
+		reg = <0x18029200 0x184>,
+		      <0x18029000 0x124>,
+		      <0x1811b408 0x004>,
+		      <0x180293a0 0x01c>;
+		reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "mspi_done",
+				  "mspi_halted",
+				  "spi_lr_fullness_reached",
+				  "spi_lr_session_aborted",
+				  "spi_lr_impatient",
+				  "spi_lr_session_done",
+				  "spi_lr_overread";
+		clocks = <&iprocmed>;
+		num-cs = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		spi_nor: flash@0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-max-frequency = <20000000>;
+			status = "disabled";
+
+			partitions {
+				compatible = "brcm,bcm947xx-cfe-partitions";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts b/arch/arm/boot/dts/broadcom/bcm53340-ubnt-unifi-switch8.dts
index 2e7fda9b998c..975f854f652f 100644
--- a/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts
+++ b/arch/arm/boot/dts/broadcom/bcm53340-ubnt-unifi-switch8.dts
@@ -34,7 +34,7 @@
 	status = "okay";
 	bspi-sel = <0>;
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80";
 		reg = <0>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/broadcom/bcm53573.dtsi
index 4af8e3293cff..2df80740d181 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm53573.dtsi
@@ -127,6 +127,9 @@
 
 		pcie0: pcie@2000 {
 			reg = <0x00002000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		usb2: usb2@4000 {
@@ -135,7 +138,7 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			ehci: ehci@4000 {
+			ehci: usb@4000 {
 				compatible = "generic-ehci";
 				reg = <0x4000 0x1000>;
 				interrupt-parent = <&gic>;
@@ -155,9 +158,7 @@
 				};
 			};
 
-			ohci: ohci@d000 {
-				#usb-cells = <0>;
-
+			ohci: usb@d000 {
 				compatible = "generic-ohci";
 				reg = <0xd000 0x1000>;
 				interrupt-parent = <&gic>;
@@ -180,10 +181,74 @@
 
 		gmac0: ethernet@5000 {
 			reg = <0x5000 0x1000>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch: switch@1e {
+					compatible = "brcm,bcm53125";
+					reg = <0x1e>;
+
+					status = "disabled";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+						};
+
+						port@1 {
+							reg = <1>;
+						};
+
+						port@2 {
+							reg = <2>;
+						};
+
+						port@3 {
+							reg = <3>;
+						};
+
+						port@4 {
+							reg = <4>;
+						};
+
+						port@5 {
+							reg = <5>;
+							ethernet = <&gmac1>;
+
+							fixed-link {
+								speed = <1000>;
+								full-duplex;
+							};
+						};
+
+						port@8 {
+							reg = <8>;
+							ethernet = <&gmac0>;
+						};
+					};
+				};
+			};
 		};
 
 		gmac1: ethernet@b000 {
 			reg = <0xb000 0x1000>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		pmu@12000 {
diff --git a/arch/arm/boot/dts/bcm59056.dtsi b/arch/arm/boot/dts/broadcom/bcm59056.dtsi
index a9bb7ad81378..a9bb7ad81378 100644
--- a/arch/arm/boot/dts/bcm59056.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm59056.dtsi
diff --git a/arch/arm/boot/dts/bcm63138.dtsi b/arch/arm/boot/dts/broadcom/bcm63138.dtsi
index 9c0325cf9e22..4ef02283612b 100644
--- a/arch/arm/boot/dts/bcm63138.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm63138.dtsi
@@ -9,8 +9,8 @@
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	compatible = "brcm,bcm63138";
-	model = "Broadcom BCM63138 DSL SoC";
+	compatible = "brcm,bcm63138", "brcm,bcmbca";
+	model = "Broadcom BCM963138 Reference Board";
 	interrupt-parent = <&gic>;
 
 	aliases {
@@ -66,6 +66,12 @@
 			clock-div = <4>;
 			clock-mult = <1>;
 		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
 	};
 
 	/* ARM bus */
@@ -203,7 +209,19 @@
 			status = "disabled";
 		};
 
-		nand: nand@2000 {
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@2000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.0", "brcm,brcmnand";
@@ -214,6 +232,12 @@
 			interrupt-names = "nand";
 		};
 
+		serial@4400 {
+			compatible = "brcm,bcm63138-hs-uart", "brcm,bcmbca-hs-uart";
+			reg = <0x4400 0x1e0>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		bootlut: bootlut@8000 {
 			compatible = "brcm,bcm63138-bootlut";
 			reg = <0x8000 0x50>;
diff --git a/arch/arm/boot/dts/broadcom/bcm63148.dtsi b/arch/arm/boot/dts/broadcom/bcm63148.dtsi
new file mode 100644
index 000000000000..24431de1810e
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm63148.dtsi
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63148", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		B15_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B15_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B15_0>, <&B15_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@80030000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x80030000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a15-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffe8000 0x8000>;
+
+		uart0: serial@600 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x600 0x20>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63148-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm63178.dtsi b/arch/arm/boot/dts/broadcom/bcm63178.dtsi
new file mode 100644
index 000000000000..3f9aed96babf
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm63178.dtsi
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63178", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63178-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6756.dtsi b/arch/arm/boot/dts/broadcom/bcm6756.dtsi
new file mode 100644
index 000000000000..1d8d957d65dd
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6756.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6756", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6756-hsspi", "brcm,bcmbca-hsspi-v1.1";
+			reg = <0x1000 0x600>, <0x2610 0x4>;
+			reg-names = "hsspi", "spim-ctrl";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6846.dtsi b/arch/arm/boot/dts/broadcom/bcm6846.dtsi
new file mode 100644
index 000000000000..cf92cf8c4693
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6846.dtsi
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6846", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x1b>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6846-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6855.dtsi b/arch/arm/boot/dts/broadcom/bcm6855.dtsi
new file mode 100644
index 000000000000..52d6bc89f9f8
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6855.dtsi
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6855", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>, <&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6855-hsspi", "brcm,bcmbca-hsspi-v1.1";
+			reg = <0x1000 0x600>, <0x2610 0x4>;
+			reg-names = "hsspi", "spim-ctrl";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6878.dtsi b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
new file mode 100644
index 000000000000..2c5d706bac7e
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6878", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6878-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts b/arch/arm/boot/dts/broadcom/bcm7445-bcm97445svmb.dts
index 8313b7cad542..f92d2cf85972 100644
--- a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
+++ b/arch/arm/boot/dts/broadcom/bcm7445-bcm97445svmb.dts
@@ -14,10 +14,10 @@
 	};
 };
 
-&nand {
+&nand_controller {
 	status = "okay";
 
-	nandcs@1 {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <1>;
 		nand-ecc-step-size = <512>;
diff --git a/arch/arm/boot/dts/bcm7445.dtsi b/arch/arm/boot/dts/broadcom/bcm7445.dtsi
index 58f67c9b830b..5ac2042515b8 100644
--- a/arch/arm/boot/dts/bcm7445.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm7445.dtsi
@@ -148,7 +148,7 @@
 			reg-names = "aon-ctrl", "aon-sram";
 		};
 
-		nand: nand@3e2800 {
+		nand_controller: nand-controller@3e2800 {
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/broadcom/bcm911360_entphn.dts
index b2d323f4a5ab..363009e747b3 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/broadcom/bcm911360_entphn.dts
@@ -47,10 +47,10 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		hook {
+		button-hook {
 			label = "HOOK";
 			linux,code = <KEY_O>;
 			gpios = <&gpio_asiu 48 0>;
@@ -82,8 +82,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/broadcom/bcm911360k.dts
index 091c73a46e08..091c73a46e08 100644
--- a/arch/arm/boot/dts/bcm911360k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm911360k.dts
diff --git a/arch/arm/boot/dts/bcm94708.dts b/arch/arm/boot/dts/broadcom/bcm94708.dts
index 3d13e46c6949..d9eb2040b963 100644
--- a/arch/arm/boot/dts/bcm94708.dts
+++ b/arch/arm/boot/dts/broadcom/bcm94708.dts
@@ -38,7 +38,7 @@
 	model = "NorthStar SVK (BCM94708)";
 	compatible = "brcm,bcm94708", "brcm,bcm4708";
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm94709.dts b/arch/arm/boot/dts/broadcom/bcm94709.dts
index 5017b7b259cb..618c812eef73 100644
--- a/arch/arm/boot/dts/bcm94709.dts
+++ b/arch/arm/boot/dts/broadcom/bcm94709.dts
@@ -38,7 +38,7 @@
 	model = "NorthStar SVK (BCM94709)";
 	compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708";
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x08000000>;
 	};
diff --git a/arch/arm/boot/dts/bcm947189acdbmr.dts b/arch/arm/boot/dts/broadcom/bcm947189acdbmr.dts
index b0b8c774a37f..0b8727ae6f16 100644
--- a/arch/arm/boot/dts/bcm947189acdbmr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm947189acdbmr.dts
@@ -25,17 +25,17 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
@@ -44,13 +44,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
@@ -60,9 +60,9 @@
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 21 0>;
-		gpio-miso = <&chipcommon 22 0>;
-		gpio-mosi = <&chipcommon 23 0>;
+		sck-gpios = <&chipcommon 21 0>;
+		miso-gpios = <&chipcommon 22 0>;
+		mosi-gpios = <&chipcommon 23 0>;
 		cs-gpios = <&chipcommon 24 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/broadcom/bcm947622.dts b/arch/arm/boot/dts/broadcom/bcm947622.dts
new file mode 100644
index 000000000000..93b8ce22678d
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm947622.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm47622.dtsi"
+
+/ {
+	model = "Broadcom BCM947622 Reference Board";
+	compatible = "brcm,bcm947622", "brcm,bcm47622", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm953012er.dts b/arch/arm/boot/dts/broadcom/bcm953012er.dts
index 957468224622..d939ec9f4a9e 100644
--- a/arch/arm/boot/dts/bcm953012er.dts
+++ b/arch/arm/boot/dts/broadcom/bcm953012er.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Enterprise Router (BCM953012ER)";
-	compatible = "brcm,bcm953012er", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012er", "brcm,bcm53012", "brcm,bcm4708";
 
 	memory@0 {
 		device_type = "memory";
@@ -47,13 +47,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
@@ -69,9 +69,6 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			reg = <0>;
 			label = "port0";
@@ -87,6 +84,14 @@
 			label = "cpu";
 			ethernet = <&gmac0>;
 		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/bcm953012hr.dts b/arch/arm/boot/dts/broadcom/bcm953012hr.dts
index 9140be7ec053..b070b69466bd 100644
--- a/arch/arm/boot/dts/bcm953012hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm953012hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar HR (BCM953012HR)";
-	compatible = "brcm,bcm953012hr", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012hr", "brcm,bcm53012", "brcm,bcm4708";
 
 	aliases {
 		ethernet0 = &gmac0;
diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/broadcom/bcm953012k.dts
index 046c59fb4846..f1e6bcaa1edd 100644
--- a/arch/arm/boot/dts/bcm953012k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm953012k.dts
@@ -36,7 +36,7 @@
 
 / {
 	model = "NorthStar SVK (BCM953012K)";
-	compatible = "brcm,bcm953012k", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012k", "brcm,bcm53012", "brcm,bcm4708";
 
 	aliases {
 		serial0 = &uart0;
@@ -49,8 +49,8 @@
 	};
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/broadcom/bcm958300k.dts
index b4a1392bd5a6..dda3e11b711f 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958300k.dts
@@ -60,8 +60,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/broadcom/bcm958305k.dts
index 3378683321d3..ea3c6b88b313 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958305k.dts
@@ -68,8 +68,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/broadcom/bcm958522er.dts
index 8c388eb8a08f..15f023656df0 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958522er.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM958522ER)";
-	compatible = "brcm,bcm58522", "brcm,nsp";
+	compatible = "brcm,bcm958522er", "brcm,bcm58522", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -58,6 +58,10 @@
 
 /* USB 3 support needed to be complete */
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -70,8 +74,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -130,8 +134,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -174,3 +179,7 @@
 &xhci {
 	status = "okay";
 };
+
+&srab {
+	compatible = "brcm,bcm58522-srab", "brcm,nsp-srab";
+};
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/broadcom/bcm958525er.dts
index c339771bb22e..9b9c225a1fb3 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958525er.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM958525ER)";
-	compatible = "brcm,bcm58525", "brcm,nsp";
+	compatible = "brcm,bcm958525er", "brcm,bcm58525", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -58,6 +58,10 @@
 
 /* USB 3 support needed to be complete */
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -70,8 +74,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -130,8 +134,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -186,3 +191,7 @@
 &xhci {
 	status = "okay";
 };
+
+&srab {
+	compatible = "brcm,bcm58525-srab", "brcm,nsp-srab";
+};
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/broadcom/bcm958525xmc.dts
index 1c72ec8288de..ca9311452739 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958525xmc.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus XMC (BCM958525xmc)";
-	compatible = "brcm,bcm58525", "brcm,nsp";
+	compatible = "brcm,bcm958525xmc", "brcm,bcm58525", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -58,6 +58,10 @@
 
 /* XHCI support needed to be complete */
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -86,8 +90,8 @@
 	};
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -146,8 +150,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -192,7 +197,7 @@
 };
 
 &sdio {
-	status = "ok";
+	status = "okay";
 };
 
 &uart0 {
@@ -206,3 +211,7 @@
 &xhci {
 	status = "okay";
 };
+
+&srab {
+	compatible = "brcm,bcm58525-srab", "brcm,nsp-srab";
+};
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/broadcom/bcm958622hr.dts
index 96a021cebd97..9db3c851451a 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958622hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM958622HR)";
-	compatible = "brcm,bcm58622", "brcm,nsp";
+	compatible = "brcm,bcm958622hr", "brcm,bcm58622", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -58,6 +58,10 @@
 
 /* USB 3 and SLIC support needed to be complete */
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -74,8 +78,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -134,8 +138,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -172,9 +177,6 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			label = "port0";
 			reg = <0>;
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/broadcom/bcm958623hr.dts
index b2c7f21d471e..32786e7c4e12 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958623hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM958623HR)";
-	compatible = "brcm,bcm58623", "brcm,nsp";
+	compatible = "brcm,bcm958623hr", "brcm,bcm58623", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -58,6 +58,10 @@
 
 /* USB 3 and SLIC support needed to be complete */
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -74,8 +78,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -138,8 +142,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -176,9 +181,6 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			label = "port0";
 			reg = <0>;
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-alamo.dtsi b/arch/arm/boot/dts/broadcom/bcm958625-meraki-alamo.dtsi
new file mode 100644
index 000000000000..c54451dde6dd
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-alamo.dtsi
@@ -0,0 +1,284 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX65 series (Alamo).
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+#include "bcm958625-meraki-mx6x-common.dtsi"
+
+/ {
+	keys {
+		compatible = "gpio-keys-polled";
+		autorepeat;
+		poll-interval = <20>;
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpioa 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/* green:wan1-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* green:wan1-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			/* green:wan2-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 27 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			/* green:wan2-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <3>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 26 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			/* amber:power */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpioa 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			/* white:status */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpioa 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&axi {
+	mdio-mux@3f1c0 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
+		reg = <0x3f1c0 0x4>;
+		mux-mask = <0x2000>;
+		mdio-parent-bus = <&mdio_ext>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			phy_port6: phy@0 {
+				reg = <0>;
+			};
+
+			phy_port7: phy@1 {
+				reg = <1>;
+			};
+
+			phy_port8: phy@2 {
+				reg = <2>;
+			};
+
+			phy_port9: phy@3 {
+				reg = <3>;
+			};
+
+			phy_port10: phy@4 {
+				reg = <4>;
+			};
+
+			switch@10 {
+				compatible = "qca,qca8337";
+				reg = <0x10>;
+				dsa,member = <1 0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+						ethernet = <&sgmii1>;
+						phy-mode = "sgmii";
+						qca,sgmii-enable-pll;
+						qca,sgmii-txclk-falling-edge;
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan8";
+						phy-handle = <&phy_port6>;
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan9";
+						phy-handle = <&phy_port7>;
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan10";
+						phy-handle = <&phy_port8>;
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan11";
+						phy-handle = <&phy_port9>;
+					};
+
+					port@5 {
+						reg = <5>;
+						label = "lan12";
+						phy-handle = <&phy_port10>;
+					};
+				};
+			};
+		};
+
+		mdio-mii@2000 {
+			reg = <0x2000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			phy_port1: phy@0 {
+				reg = <0>;
+			};
+
+			phy_port2: phy@1 {
+				reg = <1>;
+			};
+
+			phy_port3: phy@2 {
+				reg = <2>;
+			};
+
+			phy_port4: phy@3 {
+				reg = <3>;
+			};
+
+			phy_port5: phy@4 {
+				reg = <4>;
+			};
+
+			switch@10 {
+				compatible = "qca,qca8337";
+				reg = <0x10>;
+				dsa,member = <2 0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					port@0 {
+						reg = <0>;
+						ethernet = <&sgmii0>;
+						phy-mode = "sgmii";
+						qca,sgmii-enable-pll;
+						qca,sgmii-txclk-falling-edge;
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						label = "lan3";
+						phy-handle = <&phy_port1>;
+					};
+
+					port@2 {
+						reg = <2>;
+						label = "lan4";
+						phy-handle = <&phy_port2>;
+					};
+
+					port@3 {
+						reg = <3>;
+						label = "lan5";
+						phy-handle = <&phy_port3>;
+					};
+
+					port@4 {
+						reg = <4>;
+						label = "lan6";
+						phy-handle = <&phy_port4>;
+					};
+
+					port@5 {
+						reg = <5>;
+						label = "lan7";
+						phy-handle = <&phy_port5>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+	status = "okay";
+	dsa,member = <0 0>;
+
+	ports {
+		port@0 {
+			label = "wan1";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "wan2";
+			reg = <1>;
+		};
+
+		sgmii0: port@4 {
+			label = "sw0";
+			reg = <4>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		sgmii1: port@5 {
+			label = "sw1";
+			reg = <5>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-kingpin.dtsi b/arch/arm/boot/dts/broadcom/bcm958625-meraki-kingpin.dtsi
new file mode 100644
index 000000000000..1830844c8404
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-kingpin.dtsi
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64 series (Kingpin).
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+#include "bcm958625-meraki-mx6x-common.dtsi"
+
+/ {
+
+	keys {
+		compatible = "gpio-keys-polled";
+		autorepeat;
+		poll-interval = <20>;
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpioa 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/* green:lan1-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* green:lan1-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			/* green:lan2-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			/* green:lan2-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <3>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 20 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			/* green:lan3-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <4>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 26 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			/* green:lan3-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <5>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			/* green:lan4-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			/* green:lan4-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <7>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 27 GPIO_ACTIVE_LOW>;
+		};
+
+		led-8 {
+			/* green:wan-left */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <8>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 30 GPIO_ACTIVE_LOW>;
+		};
+
+		led-9 {
+			/* green:wan-right */
+			function = LED_FUNCTION_ACTIVITY;
+			function-enumerator = <9>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioa 29 GPIO_ACTIVE_LOW>;
+		};
+
+		led-a {
+			/* amber:power */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpioa 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-b {
+			/* white:status */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&gpioa 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&srab {
+	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+			reg = <0>;
+		};
+
+		port@1 {
+			label = "lan2";
+			reg = <1>;
+		};
+
+		port@2 {
+			label = "lan3";
+			reg = <2>;
+		};
+
+		port@3 {
+			label = "lan4";
+			reg = <3>;
+		};
+
+		port@4 {
+			label = "wan";
+			reg = <4>;
+		};
+
+		port@8 {
+			ethernet = <&amac2>;
+			reg = <8>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64-a0.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64-a0.dts
new file mode 100644
index 000000000000..9944566c1195
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64-a0.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64 with A0 SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+#include "bcm-nsp-ax.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64(A0)";
+	compatible = "meraki,mx64-a0", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64.dts
new file mode 100644
index 000000000000..06939438e874
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64 with B0+ SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64";
+	compatible = "meraki,mx64", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w-a0.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w-a0.dts
new file mode 100644
index 000000000000..112fddb1eed8
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w-a0.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64W with A0 SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+#include "bcm-nsp-ax.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64W(A0)";
+	compatible = "meraki,mx64w-a0", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w.dts
new file mode 100644
index 000000000000..de2e367c3e78
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX64W with B0+ SoC.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-kingpin.dtsi"
+
+/ {
+	model = "Cisco Meraki MX64W";
+	compatible = "meraki,mx64w", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65.dts
new file mode 100644
index 000000000000..d1b684dcdbfa
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX65.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-alamo.dtsi"
+
+/ {
+	model = "Cisco Meraki MX65";
+	compatible = "meraki,mx65", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65w.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65w.dts
new file mode 100644
index 000000000000..a2165aba3676
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65w.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindings for Cisco Meraki MX65W.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm958625-meraki-alamo.dtsi"
+
+/ {
+	model = "Cisco Meraki MX65W";
+	compatible = "meraki,mx65w", "brcm,bcm58625", "brcm,nsp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x80000000>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx6x-common.dtsi b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx6x-common.dtsi
new file mode 100644
index 000000000000..b0854d881ac6
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx6x-common.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Common Bindings for Cisco Meraki MX64 (Kingpin) and MX65 (Alamo) devices.
+ *
+ * Copyright (C) 2020-2021 Matthew Hagan <mnhagan88@gmail.com>
+ */
+
+#include "bcm-nsp.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			pwms = <&pwm 1 50000>;
+			max-brightness = <255>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			pwms = <&pwm 2 50000>;
+			max-brightness = <255>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			pwms = <&pwm 3 50000>;
+			max-brightness = <255>;
+		};
+	};
+};
+
+&amac2 {
+	status = "okay";
+	nvmem-cells = <&mac_address>;
+	nvmem-cell-names = "mac-address";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@66 {
+			reg = <0x66 0x6>;
+		};
+	};
+};
+
+&nand_controller {
+	nand@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "shmoo";
+			reg = <0x80000 0x80000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "bootkernel1";
+			reg = <0x100000 0x300000>;
+		};
+
+		partition@400000 {
+			label = "nvram";
+			reg = <0x400000 0x100000>;
+		};
+
+		partition@500000 {
+			label = "bootkernel2";
+			reg = <0x500000 0x300000>;
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x3f700000>;
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_leds>;
+
+	pwm_leds: pwm_leds {
+		function = "pwm";
+		groups = "pwm1_grp", "pwm2_grp", "pwm3_grp";
+	};
+};
+
+&pwm {
+	status = "okay";
+	#pwm-cells = <2>;
+};
+
+&uart0 {
+	clock-frequency = <62500000>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/broadcom/bcm958625hr.dts
index a2c9de35ddfb..74263d98de73 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM958625HR)";
-	compatible = "brcm,bcm58625", "brcm,nsp";
+	compatible = "brcm,bcm958625hr", "brcm,bcm58625", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -55,18 +55,9 @@
 		priority = <200>;
 	};
 
-	/* Hardware I2C block cannot do more than 63 bytes per transfer,
-	 * which would prevent reading from a SFP's EEPROM (256 byte).
-	 */
-	i2c1: i2c {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpioa 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpioa 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	};
-
 	sfp: sfp {
 		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
+		i2c-bus = <&i2c0>;
 		mod-def0-gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
 		los-gpios = <&gpioa 24 GPIO_ACTIVE_HIGH>;
 		tx-fault-gpios = <&gpioa 30 GPIO_ACTIVE_HIGH>;
@@ -74,6 +65,14 @@
 	};
 };
 
+&i2c0 {
+	status = "okay";
+};
+
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -90,8 +89,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -150,8 +149,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -196,9 +196,6 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			label = "port0";
 			reg = <0>;
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/broadcom/bcm958625k.dts
index 3fcca12d83c2..69ebc7a913a7 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625k.dts
@@ -36,7 +36,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM958625K)";
-	compatible = "brcm,bcm58625", "brcm,nsp";
+	compatible = "brcm,bcm958625k", "brcm,bcm58625", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -48,6 +48,10 @@
 	};
 };
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -64,8 +68,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -149,8 +153,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -204,7 +209,7 @@
 &sdio {
 	bus-width = <4>;
 	no-1-8-v;
-	status = "ok";
+	status = "okay";
 };
 
 &srab {
@@ -212,9 +217,6 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			label = "port0";
 			reg = <0>;
diff --git a/arch/arm/boot/dts/broadcom/bcm963138.dts b/arch/arm/boot/dts/broadcom/bcm963138.dts
new file mode 100644
index 000000000000..1b405c249213
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm963138.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63138.dtsi"
+
+/ {
+	model = "Broadcom BCM963138 Reference Board";
+	compatible = "brcm,bcm963138", "brcm,bcm63138", "brcm,bcmbca";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &serial0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm963138dvt.dts b/arch/arm/boot/dts/broadcom/bcm963138dvt.dts
index 5b177274f182..b5af61853a07 100644
--- a/arch/arm/boot/dts/bcm963138dvt.dts
+++ b/arch/arm/boot/dts/broadcom/bcm963138dvt.dts
@@ -8,7 +8,7 @@
 #include "bcm63138.dtsi"
 
 / {
-	compatible = "brcm,BCM963138DVT", "brcm,bcm63138";
+	compatible = "brcm,BCM963138DVT", "brcm,bcm63138", "brcm,bcmbca";
 	model = "Broadcom BCM963138DVT";
 
 	chosen {
@@ -31,10 +31,10 @@
 	status = "okay";
 };
 
-&nand {
+&nand_controller {
 	status = "okay";
 
-	nandcs@0 {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-ecc-strength = <4>;
@@ -50,3 +50,7 @@
 &sata_phy {
 	status = "okay";
 };
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm963148.dts b/arch/arm/boot/dts/broadcom/bcm963148.dts
new file mode 100644
index 000000000000..1f5d6d783f09
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm963148.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63148.dtsi"
+
+/ {
+	model = "Broadcom BCM963148 Reference Board";
+	compatible = "brcm,bcm963148", "brcm,bcm63148", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm963178.dts b/arch/arm/boot/dts/broadcom/bcm963178.dts
new file mode 100644
index 000000000000..d036e99dd8d1
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm963178.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63178.dtsi"
+
+/ {
+	model = "Broadcom BCM963178 Reference Board";
+	compatible = "brcm,bcm963178", "brcm,bcm63178", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96756.dts b/arch/arm/boot/dts/broadcom/bcm96756.dts
new file mode 100644
index 000000000000..8b104f3fb14a
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96756.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6756.dtsi"
+
+/ {
+	model = "Broadcom BCM96756 Reference Board";
+	compatible = "brcm,bcm96756", "brcm,bcm6756", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96846.dts b/arch/arm/boot/dts/broadcom/bcm96846.dts
new file mode 100644
index 000000000000..55852c229608
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96846.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6846.dtsi"
+
+/ {
+	model = "Broadcom BCM96846 Reference Board";
+	compatible = "brcm,bcm96846", "brcm,bcm6846", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96855.dts b/arch/arm/boot/dts/broadcom/bcm96855.dts
new file mode 100644
index 000000000000..2ad880af2104
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96855.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6855.dtsi"
+
+/ {
+	model = "Broadcom BCM96855 Reference Board";
+	compatible = "brcm,bcm96855", "brcm,bcm6855", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96878.dts b/arch/arm/boot/dts/broadcom/bcm96878.dts
new file mode 100644
index 000000000000..b7af8ade7a9d
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96878.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6878.dtsi"
+
+/ {
+	model = "Broadcom BCM96878 Reference Board";
+	compatible = "brcm,bcm96878", "brcm,bcm6878", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/broadcom/bcm988312hr.dts
index edd0f630e025..e96bc3f2d5cf 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm988312hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Plus SVK (BCM988312HR)";
-	compatible = "brcm,bcm88312", "brcm,nsp";
+	compatible = "brcm,bcm988312hr", "brcm,bcm88312", "brcm,nsp";
 
 	chosen {
 		stdout-path = "serial0:115200n8";
@@ -58,6 +58,10 @@
 
 /* USB 3 support needed to be complete */
 
+&dma {
+	status = "okay";
+};
+
 &amac0 {
 	status = "okay";
 };
@@ -74,8 +78,8 @@
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
@@ -134,8 +138,9 @@
 };
 
 &qspi {
+	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
@@ -184,9 +189,6 @@
 	status = "okay";
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			label = "port0";
 			reg = <0>;
diff --git a/arch/arm/boot/dts/bcm9hmidc.dtsi b/arch/arm/boot/dts/broadcom/bcm9hmidc.dtsi
index 65397c088335..65397c088335 100644
--- a/arch/arm/boot/dts/bcm9hmidc.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm9hmidc.dtsi
diff --git a/arch/arm/boot/dts/calxeda/Makefile b/arch/arm/boot/dts/calxeda/Makefile
new file mode 100644
index 000000000000..f5126b6d26ad
--- /dev/null
+++ b/arch/arm/boot/dts/calxeda/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_HIGHBANK) += \
+	highbank.dtb \
+	ecx-2000.dtb
+dtb-$(CONFIG_ARCH_HIGHBANK) += \
+	highbank.dtb \
+	ecx-2000.dtb
diff --git a/arch/arm/boot/dts/ecx-2000.dts b/arch/arm/boot/dts/calxeda/ecx-2000.dts
index 5651ae6dc969..f6eb71553b95 100644
--- a/arch/arm/boot/dts/ecx-2000.dts
+++ b/arch/arm/boot/dts/calxeda/ecx-2000.dts
@@ -13,7 +13,6 @@
 	compatible = "calxeda,ecx-2000";
 	#address-cells = <2>;
 	#size-cells = <2>;
-	clock-ranges;
 
 	cpus {
 		#address-cells = <1>;
@@ -83,8 +82,7 @@
 		intc: interrupt-controller@fff11000 {
 			compatible = "arm,cortex-a15-gic";
 			#interrupt-cells = <3>;
-			#size-cells = <0>;
-			#address-cells = <1>;
+			#address-cells = <0>;
 			interrupt-controller;
 			interrupts = <1 9 0xf04>;
 			reg = <0xfff11000 0x1000>,
@@ -95,7 +93,7 @@
 
 		pmu {
 			compatible = "arm,cortex-a9-pmu";
-			interrupts = <0 76 4  0 75 4  0 74 4  0 73 4>;
+			interrupts = <0 76 4>, <0 75 4>, <0 74 4>, <0 73 4>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/ecx-common.dtsi b/arch/arm/boot/dts/calxeda/ecx-common.dtsi
index 66ee1d34f72b..ce5221c6b358 100644
--- a/arch/arm/boot/dts/ecx-common.dtsi
+++ b/arch/arm/boot/dts/calxeda/ecx-common.dtsi
@@ -9,11 +9,11 @@
 	};
 
 	psci {
-		compatible	= "arm,psci";
-		method		= "smc";
-		cpu_suspend	= <0x84000002>;
-		cpu_off		= <0x84000004>;
-		cpu_on		= <0x84000006>;
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend = <0x84000002>;
+		cpu_off = <0x84000004>;
+		cpu_on = <0x84000006>;
 	};
 
 	soc {
@@ -27,10 +27,11 @@
 			reg = <0xffe08000 0x10000>;
 			interrupts = <0 83 4>;
 			dma-coherent;
-			calxeda,port-phys = <&combophy5 0 &combophy0 0
-					     &combophy0 1 &combophy0 2
-					     &combophy0 3>;
-			calxeda,sgpio-gpio =<&gpioh 5 1 &gpioh 6 1 &gpioh 7 1>;
+			calxeda,port-phys = < &combophy5 0>, <&combophy0 0>,
+					     <&combophy0 1>, <&combophy0 2>,
+					     <&combophy0 3>;
+			calxeda,sgpio-gpio =<&gpioh 5 1>, <&gpioh 6 1>,
+					    <&gpioh 7 1>;
 			calxeda,led-order = <4 0 1 2 3>;
 		};
 
@@ -114,8 +115,8 @@
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0xfff36000 0x1000>;
 			interrupts = <0 20 4>;
-			clocks = <&pclk>;
-			clock-names = "apb_pclk";
+			clocks = <&pclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
 		};
 
 		smic@fff3a000 {
@@ -202,14 +203,14 @@
 		ethernet@fff50000 {
 			compatible = "calxeda,hb-xgmac";
 			reg = <0xfff50000 0x1000>;
-			interrupts = <0 77 4  0 78 4  0 79 4>;
+			interrupts = <0 77 4>, <0 78 4>, <0 79 4>;
 			dma-coherent;
 		};
 
 		ethernet@fff51000 {
 			compatible = "calxeda,hb-xgmac";
 			reg = <0xfff51000 0x1000>;
-			interrupts = <0 80 4  0 81 4  0 82 4>;
+			interrupts = <0 80 4>, <0 81 4>, <0 82 4>;
 			dma-coherent;
 		};
 
diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/calxeda/highbank.dts
index f4e4dca6f7e7..b6b0225a769e 100644
--- a/arch/arm/boot/dts/highbank.dts
+++ b/arch/arm/boot/dts/calxeda/highbank.dts
@@ -13,7 +13,6 @@
 	compatible = "calxeda,highbank";
 	#address-cells = <1>;
 	#size-cells = <1>;
-	clock-ranges;
 
 	cpus {
 		#address-cells = <1>;
@@ -96,7 +95,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		name = "memory";
 		device_type = "memory";
 		reg = <0x00000000 0xff900000>;
@@ -128,14 +127,12 @@
 		intc: interrupt-controller@fff11000 {
 			compatible = "arm,cortex-a9-gic";
 			#interrupt-cells = <3>;
-			#size-cells = <0>;
-			#address-cells = <1>;
 			interrupt-controller;
 			reg = <0xfff11000 0x1000>,
 			      <0xfff10100 0x100>;
 		};
 
-		L2: l2-cache {
+		L2: cache-controller {
 			compatible = "arm,pl310-cache";
 			reg = <0xfff12000 0x1000>;
 			interrupts = <0 70 4>;
@@ -145,14 +142,14 @@
 
 		pmu {
 			compatible = "arm,cortex-a9-pmu";
-			interrupts = <0 76 4  0 75 4  0 74 4  0 73 4>;
+			interrupts = <0 76 4>, <0 75 4>, <0 74 4>, <0 73 4>;
 		};
 
 
 		sregs@fff3c200 {
 			compatible = "calxeda,hb-sregs-l2-ecc";
 			reg = <0xfff3c200 0x100>;
-			interrupts = <0 71 4  0 72 4>;
+			interrupts = <0 71 4>, <0 72 4>;
 		};
 
 	};
diff --git a/arch/arm/boot/dts/cirrus/Makefile b/arch/arm/boot/dts/cirrus/Makefile
new file mode 100644
index 000000000000..e944d3e2129d
--- /dev/null
+++ b/arch/arm/boot/dts/cirrus/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/cirrus/ep7209.dtsi
index 365931f8b48d..57bdad2c1994 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/cirrus/ep7209.dtsi
@@ -10,6 +10,8 @@
 	model = "Cirrus Logic EP7209";
 	compatible = "cirrus,ep7209";
 
+	chosen { };
+
 	aliases {
 		gpio0 = &porta;
 		gpio1 = &portb;
@@ -108,6 +110,7 @@
 			compatible = "cirrus,ep7209-fb";
 			reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
 			clocks = <&clks CLPS711X_CLK_BUS>;
+			syscon = <&syscon1>;
 			status = "disabled";
 		};
 
@@ -132,7 +135,7 @@
 			#pwm-cells = <1>;
 		};
 
-		uart1: uart@80000480 {
+		uart1: serial@80000480 {
 			compatible = "cirrus,ep7209-uart";
 			reg = <0x80000480 0x80>;
 			interrupts = <12 13>;
@@ -147,6 +150,7 @@
 			reg = <0x80000500 0x4>;
 			interrupts = <15>;
 			clocks = <&clks CLPS711X_CLK_SPI>;
+			syscon = <&syscon3>;
 			status = "disabled";
 		};
 
@@ -155,7 +159,7 @@
 			reg = <0x80001100 0x80>;
 		};
 
-		uart2: uart@80001480 {
+		uart2: serial@80001480 {
 			compatible = "cirrus,ep7209-uart";
 			reg = <0x80001480 0x80>;
 			interrupts = <28 29>;
@@ -170,6 +174,7 @@
 			clocks = <&clks CLPS711X_CLK_PLL>;
 			clock-names = "pll";
 			interrupts = <32>;
+			syscon = <&syscon3>;
 			status = "disabled";
 		};
 
@@ -179,8 +184,17 @@
 		};
 	};
 
+	keypad: keypad {
+		compatible = "cirrus,ep7209-keypad";
+		interrupt-parent = <&intc>;
+		interrupts = <16>;
+		syscon = <&syscon1>;
+		status = "disabled";
+	};
+
 	mctrl: mctrl {
 		compatible = "cirrus,ep7209-mctrl-gpio";
+		gpio,syscon-dev = <&syscon1 0 0>;
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
diff --git a/arch/arm/boot/dts/ep7211-edb7211.dts b/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts
index da076479c8e2..7fb532f227af 100644
--- a/arch/arm/boot/dts/ep7211-edb7211.dts
+++ b/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts
@@ -7,7 +7,7 @@
 	model = "Cirrus Logic EP7211 Development Board";
 	compatible = "cirrus,edb7211", "cirrus,ep7211", "cirrus,ep7209";
 
-	memory {
+	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xc0000000 0x02000000>;
 	};
diff --git a/arch/arm/boot/dts/ep7211.dtsi b/arch/arm/boot/dts/cirrus/ep7211.dtsi
index 32a4e1237145..32a4e1237145 100644
--- a/arch/arm/boot/dts/ep7211.dtsi
+++ b/arch/arm/boot/dts/cirrus/ep7211.dtsi
diff --git a/arch/arm/boot/dts/cnxt/Makefile b/arch/arm/boot/dts/cnxt/Makefile
new file mode 100644
index 000000000000..d49df53f65a1
--- /dev/null
+++ b/arch/arm/boot/dts/cnxt/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_DIGICOLOR) += \
+	cx92755_equinox.dtb
+dtb-$(CONFIG_ARCH_DIGICOLOR) += \
+	cx92755_equinox.dtb
diff --git a/arch/arm/boot/dts/cx92755.dtsi b/arch/arm/boot/dts/cnxt/cx92755.dtsi
index d2e8f36f8c60..227675fbe820 100644
--- a/arch/arm/boot/dts/cx92755.dtsi
+++ b/arch/arm/boot/dts/cnxt/cx92755.dtsi
@@ -107,7 +107,7 @@
 		reg = <0xf00003a0 0x10>;
 	};
 
-	uart0: uart@f0000740 {
+	uart0: serial@f0000740 {
 		compatible = "cnxt,cx92755-usart";
 		reg = <0xf0000740 0x20>;
 		clocks = <&main_clk>;
@@ -115,7 +115,7 @@
 		status = "disabled";
 	};
 
-	uart1: uart@f0000760 {
+	uart1: serial@f0000760 {
 		compatible = "cnxt,cx92755-usart";
 		reg = <0xf0000760 0x20>;
 		clocks = <&main_clk>;
@@ -123,7 +123,7 @@
 		status = "disabled";
 	};
 
-	uart2: uart@f0000780 {
+	uart2: serial@f0000780 {
 		compatible = "cnxt,cx92755-usart";
 		reg = <0xf0000780 0x20>;
 		clocks = <&main_clk>;
diff --git a/arch/arm/boot/dts/cx92755_equinox.dts b/arch/arm/boot/dts/cnxt/cx92755_equinox.dts
index 026f556c8c50..026f556c8c50 100644
--- a/arch/arm/boot/dts/cx92755_equinox.dts
+++ b/arch/arm/boot/dts/cnxt/cx92755_equinox.dts
diff --git a/arch/arm/boot/dts/cros-ec-keyboard.dtsi b/arch/arm/boot/dts/cros-ec-keyboard.dtsi
index 4a0c1037fbc0..55c4744fa7e7 100644
--- a/arch/arm/boot/dts/cros-ec-keyboard.dtsi
+++ b/arch/arm/boot/dts/cros-ec-keyboard.dtsi
@@ -6,102 +6,18 @@
 */
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/input/cros-ec-keyboard.h>
 
 &cros_ec {
-	keyboard-controller {
+	keyboard_controller: keyboard-controller {
 		compatible = "google,cros-ec-keyb";
 		keypad,num-rows = <8>;
 		keypad,num-columns = <13>;
 		google,needs-ghost-filter;
 
 		linux,keymap = <
-			MATRIX_KEY(0x00, 0x01, KEY_LEFTMETA)
-			MATRIX_KEY(0x00, 0x02, KEY_F1)
-			MATRIX_KEY(0x00, 0x03, KEY_B)
-			MATRIX_KEY(0x00, 0x04, KEY_F10)
-			MATRIX_KEY(0x00, 0x05, KEY_RO)
-			MATRIX_KEY(0x00, 0x06, KEY_N)
-			MATRIX_KEY(0x00, 0x08, KEY_EQUAL)
-			MATRIX_KEY(0x00, 0x0a, KEY_RIGHTALT)
-
-			MATRIX_KEY(0x01, 0x01, KEY_ESC)
-			MATRIX_KEY(0x01, 0x02, KEY_F4)
-			MATRIX_KEY(0x01, 0x03, KEY_G)
-			MATRIX_KEY(0x01, 0x04, KEY_F7)
-			MATRIX_KEY(0x01, 0x06, KEY_H)
-			MATRIX_KEY(0x01, 0x08, KEY_APOSTROPHE)
-			MATRIX_KEY(0x01, 0x09, KEY_F9)
-			MATRIX_KEY(0x01, 0x0b, KEY_BACKSPACE)
-			MATRIX_KEY(0x01, 0x0c, KEY_HENKAN)
-
-			MATRIX_KEY(0x02, 0x00, KEY_LEFTCTRL)
-			MATRIX_KEY(0x02, 0x01, KEY_TAB)
-			MATRIX_KEY(0x02, 0x02, KEY_F3)
-			MATRIX_KEY(0x02, 0x03, KEY_T)
-			MATRIX_KEY(0x02, 0x04, KEY_F6)
-			MATRIX_KEY(0x02, 0x05, KEY_RIGHTBRACE)
-			MATRIX_KEY(0x02, 0x06, KEY_Y)
-			MATRIX_KEY(0x02, 0x07, KEY_102ND)
-			MATRIX_KEY(0x02, 0x08, KEY_LEFTBRACE)
-			MATRIX_KEY(0x02, 0x09, KEY_F8)
-			MATRIX_KEY(0x02, 0x0a, KEY_YEN)
-
-			MATRIX_KEY(0x03, 0x01, KEY_GRAVE)
-			MATRIX_KEY(0x03, 0x02, KEY_F2)
-			MATRIX_KEY(0x03, 0x03, KEY_5)
-			MATRIX_KEY(0x03, 0x04, KEY_F5)
-			MATRIX_KEY(0x03, 0x06, KEY_6)
-			MATRIX_KEY(0x03, 0x08, KEY_MINUS)
-			MATRIX_KEY(0x03, 0x09, KEY_F13)
-			MATRIX_KEY(0x03, 0x0b, KEY_BACKSLASH)
-			MATRIX_KEY(0x03, 0x0c, KEY_MUHENKAN)
-
-			MATRIX_KEY(0x04, 0x00, KEY_RIGHTCTRL)
-			MATRIX_KEY(0x04, 0x01, KEY_A)
-			MATRIX_KEY(0x04, 0x02, KEY_D)
-			MATRIX_KEY(0x04, 0x03, KEY_F)
-			MATRIX_KEY(0x04, 0x04, KEY_S)
-			MATRIX_KEY(0x04, 0x05, KEY_K)
-			MATRIX_KEY(0x04, 0x06, KEY_J)
-			MATRIX_KEY(0x04, 0x08, KEY_SEMICOLON)
-			MATRIX_KEY(0x04, 0x09, KEY_L)
-			MATRIX_KEY(0x04, 0x0a, KEY_BACKSLASH)
-			MATRIX_KEY(0x04, 0x0b, KEY_ENTER)
-
-			MATRIX_KEY(0x05, 0x01, KEY_Z)
-			MATRIX_KEY(0x05, 0x02, KEY_C)
-			MATRIX_KEY(0x05, 0x03, KEY_V)
-			MATRIX_KEY(0x05, 0x04, KEY_X)
-			MATRIX_KEY(0x05, 0x05, KEY_COMMA)
-			MATRIX_KEY(0x05, 0x06, KEY_M)
-			MATRIX_KEY(0x05, 0x07, KEY_LEFTSHIFT)
-			MATRIX_KEY(0x05, 0x08, KEY_SLASH)
-			MATRIX_KEY(0x05, 0x09, KEY_DOT)
-			MATRIX_KEY(0x05, 0x0b, KEY_SPACE)
-
-			MATRIX_KEY(0x06, 0x01, KEY_1)
-			MATRIX_KEY(0x06, 0x02, KEY_3)
-			MATRIX_KEY(0x06, 0x03, KEY_4)
-			MATRIX_KEY(0x06, 0x04, KEY_2)
-			MATRIX_KEY(0x06, 0x05, KEY_8)
-			MATRIX_KEY(0x06, 0x06, KEY_7)
-			MATRIX_KEY(0x06, 0x08, KEY_0)
-			MATRIX_KEY(0x06, 0x09, KEY_9)
-			MATRIX_KEY(0x06, 0x0a, KEY_LEFTALT)
-			MATRIX_KEY(0x06, 0x0b, KEY_DOWN)
-			MATRIX_KEY(0x06, 0x0c, KEY_RIGHT)
-
-			MATRIX_KEY(0x07, 0x01, KEY_Q)
-			MATRIX_KEY(0x07, 0x02, KEY_E)
-			MATRIX_KEY(0x07, 0x03, KEY_R)
-			MATRIX_KEY(0x07, 0x04, KEY_W)
-			MATRIX_KEY(0x07, 0x05, KEY_I)
-			MATRIX_KEY(0x07, 0x06, KEY_U)
-			MATRIX_KEY(0x07, 0x07, KEY_RIGHTSHIFT)
-			MATRIX_KEY(0x07, 0x08, KEY_P)
-			MATRIX_KEY(0x07, 0x09, KEY_O)
-			MATRIX_KEY(0x07, 0x0b, KEY_UP)
-			MATRIX_KEY(0x07, 0x0c, KEY_LEFT)
+			CROS_STD_TOP_ROW_KEYMAP
+			CROS_STD_MAIN_KEYMAP
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/dra62x.dtsi b/arch/arm/boot/dts/dra62x.dtsi
deleted file mode 100644
index d3cbb4ea35a8..000000000000
--- a/arch/arm/boot/dts/dra62x.dtsi
+++ /dev/null
@@ -1,23 +0,0 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include "dm814x.dtsi"
-
-/ {
-	compatible = "ti,dra62x";
-};
-
-/* Compared to dm814x, dra62x has different offsets for Ethernet */
-&mac {
-	reg = <0x4a100000 0x800
-		0x4a101200 0x100>;
-};
-
-&davinci_mdio {
-	reg = <0x4a101000 0x100>;
-};
-
-#include "dra62x-clocks.dtsi"
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
deleted file mode 100644
index 73e5011f531a..000000000000
--- a/arch/arm/boot/dts/dra7.dtsi
+++ /dev/null
@@ -1,816 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on "omap4.dtsi"
- */
-
-#include <dt-bindings/bus/ti-sysc.h>
-#include <dt-bindings/clock/dra7.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/dra.h>
-#include <dt-bindings/clock/dra7.h>
-
-#define MAX_SOURCES 400
-
-/ {
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	compatible = "ti,dra7xx";
-	interrupt-parent = <&crossbar_mpu>;
-	chosen { };
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c2;
-		i2c2 = &i2c3;
-		i2c3 = &i2c4;
-		i2c4 = &i2c5;
-		serial0 = &uart1;
-		serial1 = &uart2;
-		serial2 = &uart3;
-		serial3 = &uart4;
-		serial4 = &uart5;
-		serial5 = &uart6;
-		serial6 = &uart7;
-		serial7 = &uart8;
-		serial8 = &uart9;
-		serial9 = &uart10;
-		ethernet0 = &cpsw_emac0;
-		ethernet1 = &cpsw_emac1;
-		d_can0 = &dcan1;
-		d_can1 = &dcan2;
-		spi0 = &qspi;
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
-		interrupt-parent = <&gic>;
-	};
-
-	gic: interrupt-controller@48211000 {
-		compatible = "arm,cortex-a15-gic";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0x0 0x48211000 0x0 0x1000>,
-		      <0x0 0x48212000 0x0 0x2000>,
-		      <0x0 0x48214000 0x0 0x2000>,
-		      <0x0 0x48216000 0x0 0x2000>;
-		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
-		interrupt-parent = <&gic>;
-	};
-
-	wakeupgen: interrupt-controller@48281000 {
-		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0x0 0x48281000 0x0 0x1000>;
-		interrupt-parent = <&gic>;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a15";
-			reg = <0>;
-
-			operating-points-v2 = <&cpu0_opp_table>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-
-			/* cooling options */
-			#cooling-cells = <2>; /* min followed by max */
-
-			vbb-supply = <&abb_mpu>;
-		};
-	};
-
-	cpu0_opp_table: opp-table {
-		compatible = "operating-points-v2-ti-cpu";
-		syscon = <&scm_wkup>;
-
-		opp_nom-1000000000 {
-			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <1060000 850000 1150000>,
-					<1060000 850000 1150000>;
-			opp-supported-hw = <0xFF 0x01>;
-			opp-suspend;
-		};
-
-		opp_od-1176000000 {
-			opp-hz = /bits/ 64 <1176000000>;
-			opp-microvolt = <1160000 885000 1160000>,
-					<1160000 885000 1160000>;
-
-			opp-supported-hw = <0xFF 0x02>;
-		};
-
-		opp_high@1500000000 {
-			opp-hz = /bits/ 64 <1500000000>;
-			opp-microvolt = <1210000 950000 1250000>,
-					<1210000 950000 1250000>;
-			opp-supported-hw = <0xFF 0x04>;
-		};
-	};
-
-	/*
-	 * The soc node represents the soc top level view. It is used for IPs
-	 * that are not memory mapped in the MPU view or for the MPU itself.
-	 */
-	soc {
-		compatible = "ti,omap-infra";
-		mpu {
-			compatible = "ti,omap5-mpu";
-			ti,hwmods = "mpu";
-		};
-	};
-
-	/*
-	 * XXX: Use a flat representation of the SOC interconnect.
-	 * The real OMAP interconnect network is quite complex.
-	 * Since it will not bring real advantage to represent that in DT for
-	 * the moment, just use a fake OCP bus entry to represent the whole bus
-	 * hierarchy.
-	 */
-	ocp {
-		compatible = "ti,dra7-l3-noc", "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x0 0x0 0x0 0xc0000000>;
-		ti,hwmods = "l3_main_1", "l3_main_2";
-		reg = <0x0 0x44000000 0x0 0x1000000>,
-		      <0x0 0x45000000 0x0 0x1000>;
-		interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-				      <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-
-		l4_cfg: interconnect@4a000000 {
-		};
-		l4_wkup: interconnect@4ae00000 {
-		};
-		l4_per1: interconnect@48000000 {
-		};
-		l4_per2: interconnect@48400000 {
-		};
-		l4_per3: interconnect@48800000 {
-		};
-
-		axi@0 {
-			compatible = "simple-bus";
-			#size-cells = <1>;
-			#address-cells = <1>;
-			ranges = <0x51000000 0x51000000 0x3000
-				  0x0	     0x20000000 0x10000000>;
-			/**
-			 * To enable PCI endpoint mode, disable the pcie1_rc
-			 * node and enable pcie1_ep mode.
-			 */
-			pcie1_rc: pcie@51000000 {
-				reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>;
-				reg-names = "rc_dbics", "ti_conf", "config";
-				interrupts = <0 232 0x4>, <0 233 0x4>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				device_type = "pci";
-				ranges = <0x81000000 0 0          0x03000 0 0x00010000
-					  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
-				bus-range = <0x00 0xff>;
-				#interrupt-cells = <1>;
-				num-lanes = <1>;
-				linux,pci-domain = <0>;
-				ti,hwmods = "pcie1";
-				phys = <&pcie1_phy>;
-				phy-names = "pcie-phy0";
-				ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
-				interrupt-map-mask = <0 0 0 7>;
-				interrupt-map = <0 0 0 1 &pcie1_intc 1>,
-						<0 0 0 2 &pcie1_intc 2>,
-						<0 0 0 3 &pcie1_intc 3>,
-						<0 0 0 4 &pcie1_intc 4>;
-				ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
-				status = "disabled";
-				pcie1_intc: interrupt-controller {
-					interrupt-controller;
-					#address-cells = <0>;
-					#interrupt-cells = <1>;
-				};
-			};
-
-			pcie1_ep: pcie_ep@51000000 {
-				reg = <0x51000000 0x28>, <0x51002000 0x14c>, <0x51001000 0x28>, <0x1000 0x10000000>;
-				reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
-				interrupts = <0 232 0x4>;
-				num-lanes = <1>;
-				num-ib-windows = <4>;
-				num-ob-windows = <16>;
-				ti,hwmods = "pcie1";
-				phys = <&pcie1_phy>;
-				phy-names = "pcie-phy0";
-				ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
-				ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
-				status = "disabled";
-			};
-		};
-
-		axi@1 {
-			compatible = "simple-bus";
-			#size-cells = <1>;
-			#address-cells = <1>;
-			ranges = <0x51800000 0x51800000 0x3000
-				  0x0	     0x30000000 0x10000000>;
-			status = "disabled";
-			pcie2_rc: pcie@51800000 {
-				reg = <0x51800000 0x2000>, <0x51802000 0x14c>, <0x1000 0x2000>;
-				reg-names = "rc_dbics", "ti_conf", "config";
-				interrupts = <0 355 0x4>, <0 356 0x4>;
-				#address-cells = <3>;
-				#size-cells = <2>;
-				device_type = "pci";
-				ranges = <0x81000000 0 0          0x03000 0 0x00010000
-					  0x82000000 0 0x30013000 0x13000 0 0xffed000>;
-				bus-range = <0x00 0xff>;
-				#interrupt-cells = <1>;
-				num-lanes = <1>;
-				linux,pci-domain = <1>;
-				ti,hwmods = "pcie2";
-				phys = <&pcie2_phy>;
-				phy-names = "pcie-phy0";
-				interrupt-map-mask = <0 0 0 7>;
-				interrupt-map = <0 0 0 1 &pcie2_intc 1>,
-						<0 0 0 2 &pcie2_intc 2>,
-						<0 0 0 3 &pcie2_intc 3>,
-						<0 0 0 4 &pcie2_intc 4>;
-				ti,syscon-unaligned-access = <&scm_conf1 0x14 2>;
-				pcie2_intc: interrupt-controller {
-					interrupt-controller;
-					#address-cells = <0>;
-					#interrupt-cells = <1>;
-				};
-			};
-		};
-
-		ocmcram1: ocmcram@40300000 {
-			compatible = "mmio-sram";
-			reg = <0x40300000 0x80000>;
-			ranges = <0x0 0x40300000 0x80000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			/*
-			 * This is a placeholder for an optional reserved
-			 * region for use by secure software. The size
-			 * of this region is not known until runtime so it
-			 * is set as zero to either be updated to reserve
-			 * space or left unchanged to leave all SRAM for use.
-			 * On HS parts that that require the reserved region
-			 * either the bootloader can update the size to
-			 * the required amount or the node can be overridden
-			 * from the board dts file for the secure platform.
-			 */
-			sram-hs@0 {
-				compatible = "ti,secure-ram";
-				reg = <0x0 0x0>;
-			};
-		};
-
-		/*
-		 * NOTE: ocmcram2 and ocmcram3 are not available on all
-		 * DRA7xx and AM57xx variants. Confirm availability in
-		 * the data manual for the exact part number in use
-		 * before enabling these nodes in the board dts file.
-		 */
-		ocmcram2: ocmcram@40400000 {
-			status = "disabled";
-			compatible = "mmio-sram";
-			reg = <0x40400000 0x100000>;
-			ranges = <0x0 0x40400000 0x100000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-		};
-
-		ocmcram3: ocmcram@40500000 {
-			status = "disabled";
-			compatible = "mmio-sram";
-			reg = <0x40500000 0x100000>;
-			ranges = <0x0 0x40500000 0x100000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-		};
-
-		bandgap: bandgap@4a0021e0 {
-			reg = <0x4a0021e0 0xc
-				0x4a00232c 0xc
-				0x4a002380 0x2c
-				0x4a0023C0 0x3c
-				0x4a002564 0x8
-				0x4a002574 0x50>;
-				compatible = "ti,dra752-bandgap";
-				interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
-				#thermal-sensor-cells = <1>;
-		};
-
-		dsp1_system: dsp_system@40d00000 {
-			compatible = "syscon";
-			reg = <0x40d00000 0x100>;
-		};
-
-		dra7_iodelay_core: padconf@4844a000 {
-			compatible = "ti,dra7-iodelay";
-			reg = <0x4844a000 0x0d1c>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			#pinctrl-cells = <2>;
-		};
-
-		edma: edma@43300000 {
-			compatible = "ti,edma3-tpcc";
-			ti,hwmods = "tpcc";
-			reg = <0x43300000 0x100000>;
-			reg-names = "edma3_cc";
-			interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_ccint", "edma3_mperr",
-					  "edma3_ccerrint";
-			dma-requests = <64>;
-			#dma-cells = <2>;
-
-			ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 0>;
-
-			/*
-			 * memcpy is disabled, can be enabled with:
-			 * ti,edma-memcpy-channels = <20 21>;
-			 * for example. Note that these channels need to be
-			 * masked in the xbar as well.
-			 */
-		};
-
-		edma_tptc0: tptc@43400000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc0";
-			reg =	<0x43400000 0x100000>;
-			interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		edma_tptc1: tptc@43500000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc1";
-			reg =	<0x43500000 0x100000>;
-			interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "edma3_tcerrint";
-		};
-
-		dmm@4e000000 {
-			compatible = "ti,omap5-dmm";
-			reg = <0x4e000000 0x800>;
-			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "dmm";
-		};
-
-		mmu0_dsp1: mmu@40d01000 {
-			compatible = "ti,dra7-dsp-iommu";
-			reg = <0x40d01000 0x100>;
-			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu0_dsp1";
-			#iommu-cells = <0>;
-			ti,syscon-mmuconfig = <&dsp1_system 0x0>;
-			status = "disabled";
-		};
-
-		mmu1_dsp1: mmu@40d02000 {
-			compatible = "ti,dra7-dsp-iommu";
-			reg = <0x40d02000 0x100>;
-			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu1_dsp1";
-			#iommu-cells = <0>;
-			ti,syscon-mmuconfig = <&dsp1_system 0x1>;
-			status = "disabled";
-		};
-
-		mmu_ipu1: mmu@58882000 {
-			compatible = "ti,dra7-iommu";
-			reg = <0x58882000 0x100>;
-			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu_ipu1";
-			#iommu-cells = <0>;
-			ti,iommu-bus-err-back;
-			status = "disabled";
-		};
-
-		mmu_ipu2: mmu@55082000 {
-			compatible = "ti,dra7-iommu";
-			reg = <0x55082000 0x100>;
-			interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu_ipu2";
-			#iommu-cells = <0>;
-			ti,iommu-bus-err-back;
-			status = "disabled";
-		};
-
-		abb_mpu: regulator-abb-mpu {
-			compatible = "ti,abb-v3";
-			regulator-name = "abb_mpu";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			clocks = <&sys_clkin1>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
-			      <0x4ae06014 0x4>, <0x4a003b20 0xc>,
-			      <0x4ae0c158 0x4>;
-			reg-names = "setup-address", "control-address",
-				    "int-address", "efuse-address",
-				    "ldo-address";
-			ti,tranxdone-status-mask = <0x80>;
-			/* LDOVBBMPU_FBB_MUX_CTRL */
-			ti,ldovbb-override-mask = <0x400>;
-			/* LDOVBBMPU_FBB_VSET_OUT */
-			ti,ldovbb-vset-mask = <0x1F>;
-
-			/*
-			 * NOTE: only FBB mode used but actual vset will
-			 * determine final biasing
-			 */
-			ti,abb_info = <
-			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
-			1060000		0	0x0	0 0x02000000 0x01F00000
-			1160000		0	0x4	0 0x02000000 0x01F00000
-			1210000		0	0x8	0 0x02000000 0x01F00000
-			>;
-		};
-
-		abb_ivahd: regulator-abb-ivahd {
-			compatible = "ti,abb-v3";
-			regulator-name = "abb_ivahd";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			clocks = <&sys_clkin1>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
-			      <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
-			      <0x4a002470 0x4>;
-			reg-names = "setup-address", "control-address",
-				    "int-address", "efuse-address",
-				    "ldo-address";
-			ti,tranxdone-status-mask = <0x40000000>;
-			/* LDOVBBIVA_FBB_MUX_CTRL */
-			ti,ldovbb-override-mask = <0x400>;
-			/* LDOVBBIVA_FBB_VSET_OUT */
-			ti,ldovbb-vset-mask = <0x1F>;
-
-			/*
-			 * NOTE: only FBB mode used but actual vset will
-			 * determine final biasing
-			 */
-			ti,abb_info = <
-			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
-			1055000		0	0x0	0 0x02000000 0x01F00000
-			1150000		0	0x4	0 0x02000000 0x01F00000
-			1250000		0	0x8	0 0x02000000 0x01F00000
-			>;
-		};
-
-		abb_dspeve: regulator-abb-dspeve {
-			compatible = "ti,abb-v3";
-			regulator-name = "abb_dspeve";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			clocks = <&sys_clkin1>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
-			      <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
-			      <0x4a00246c 0x4>;
-			reg-names = "setup-address", "control-address",
-				    "int-address", "efuse-address",
-				    "ldo-address";
-			ti,tranxdone-status-mask = <0x20000000>;
-			/* LDOVBBDSPEVE_FBB_MUX_CTRL */
-			ti,ldovbb-override-mask = <0x400>;
-			/* LDOVBBDSPEVE_FBB_VSET_OUT */
-			ti,ldovbb-vset-mask = <0x1F>;
-
-			/*
-			 * NOTE: only FBB mode used but actual vset will
-			 * determine final biasing
-			 */
-			ti,abb_info = <
-			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
-			1055000		0	0x0	0 0x02000000 0x01F00000
-			1150000		0	0x4	0 0x02000000 0x01F00000
-			1250000		0	0x8	0 0x02000000 0x01F00000
-			>;
-		};
-
-		abb_gpu: regulator-abb-gpu {
-			compatible = "ti,abb-v3";
-			regulator-name = "abb_gpu";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			clocks = <&sys_clkin1>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
-			      <0x4ae06010 0x4>, <0x4a003b08 0xc>,
-			      <0x4ae0c154 0x4>;
-			reg-names = "setup-address", "control-address",
-				    "int-address", "efuse-address",
-				    "ldo-address";
-			ti,tranxdone-status-mask = <0x10000000>;
-			/* LDOVBBGPU_FBB_MUX_CTRL */
-			ti,ldovbb-override-mask = <0x400>;
-			/* LDOVBBGPU_FBB_VSET_OUT */
-			ti,ldovbb-vset-mask = <0x1F>;
-
-			/*
-			 * NOTE: only FBB mode used but actual vset will
-			 * determine final biasing
-			 */
-			ti,abb_info = <
-			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
-			1090000		0	0x0	0 0x02000000 0x01F00000
-			1210000		0	0x4	0 0x02000000 0x01F00000
-			1280000		0	0x8	0 0x02000000 0x01F00000
-			>;
-		};
-
-		qspi: spi@4b300000 {
-			compatible = "ti,dra7xxx-qspi";
-			reg = <0x4b300000 0x100>,
-			      <0x5c000000 0x4000000>;
-			reg-names = "qspi_base", "qspi_mmap";
-			syscon-chipselects = <&scm_conf 0x558>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			ti,hwmods = "qspi";
-			clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>;
-			clock-names = "fck";
-			num-cs = <4>;
-			interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		/* OCP2SCP3 */
-		sata: sata@4a141100 {
-			compatible = "snps,dwc-ahci";
-			reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
-			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&sata_phy>;
-			phy-names = "sata-phy";
-			clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 8>;
-			ti,hwmods = "sata";
-			ports-implemented = <0x1>;
-		};
-
-		/* OCP2SCP1 */
-		/* IRQ for DWC3_3 and DWC3_4 need IRQ crossbar */
-		gpmc: gpmc@50000000 {
-			compatible = "ti,am3352-gpmc";
-			ti,hwmods = "gpmc";
-			reg = <0x50000000 0x37c>;      /* device IO registers */
-			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&edma_xbar 4 0>;
-			dma-names = "rxtx";
-			gpmc,num-cs = <8>;
-			gpmc,num-waitpins = <2>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			status = "disabled";
-		};
-
-		crossbar_mpu: crossbar@4a002a48 {
-			compatible = "ti,irq-crossbar";
-			reg = <0x4a002a48 0x130>;
-			interrupt-controller;
-			interrupt-parent = <&wakeupgen>;
-			#interrupt-cells = <3>;
-			ti,max-irqs = <160>;
-			ti,max-crossbar-sources = <MAX_SOURCES>;
-			ti,reg-size = <2>;
-			ti,irqs-reserved = <0 1 2 3 5 6 131 132>;
-			ti,irqs-skip = <10 133 139 140>;
-			ti,irqs-safe-map = <0>;
-		};
-
-		dss: dss@58000000 {
-			compatible = "ti,dra7-dss";
-			/* 'reg' defined in dra72x.dtsi and dra74x.dtsi */
-			/* 'clocks' defined in dra72x.dtsi and dra74x.dtsi */
-			status = "disabled";
-			ti,hwmods = "dss_core";
-			/* CTRL_CORE_DSS_PLL_CONTROL */
-			syscon-pll-ctrl = <&scm_conf 0x538>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			dispc@58001000 {
-				compatible = "ti,dra7-dispc";
-				reg = <0x58001000 0x1000>;
-				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
-				ti,hwmods = "dss_dispc";
-				clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
-				clock-names = "fck";
-				/* CTRL_CORE_SMA_SW_1 */
-				syscon-pol = <&scm_conf 0x534>;
-			};
-
-			hdmi: encoder@58060000 {
-				compatible = "ti,dra7-hdmi";
-				reg = <0x58040000 0x200>,
-				      <0x58040200 0x80>,
-				      <0x58040300 0x80>,
-				      <0x58060000 0x19000>;
-				reg-names = "wp", "pll", "phy", "core";
-				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_hdmi";
-				clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
-					 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-				dmas = <&sdma_xbar 76>;
-				dma-names = "audio_tx";
-			};
-		};
-
-		aes1: aes@4b500000 {
-			compatible = "ti,omap4-aes";
-			ti,hwmods = "aes1";
-			reg = <0x4b500000 0xa0>;
-			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&edma_xbar 111 0>, <&edma_xbar 110 0>;
-			dma-names = "tx", "rx";
-			clocks = <&l3_iclk_div>;
-			clock-names = "fck";
-		};
-
-		aes2: aes@4b700000 {
-			compatible = "ti,omap4-aes";
-			ti,hwmods = "aes2";
-			reg = <0x4b700000 0xa0>;
-			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&edma_xbar 114 0>, <&edma_xbar 113 0>;
-			dma-names = "tx", "rx";
-			clocks = <&l3_iclk_div>;
-			clock-names = "fck";
-		};
-
-		des: des@480a5000 {
-			compatible = "ti,omap4-des";
-			ti,hwmods = "des";
-			reg = <0x480a5000 0xa0>;
-			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma_xbar 117>, <&sdma_xbar 116>;
-			dma-names = "tx", "rx";
-			clocks = <&l3_iclk_div>;
-			clock-names = "fck";
-		};
-
-		sham: sham@53100000 {
-			compatible = "ti,omap5-sham";
-			ti,hwmods = "sham";
-			reg = <0x4b101000 0x300>;
-			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&edma_xbar 119 0>;
-			dma-names = "rx";
-			clocks = <&l3_iclk_div>;
-			clock-names = "fck";
-		};
-
-		opp_supply_mpu: opp-supply@4a003b20 {
-			compatible = "ti,omap5-opp-supply";
-			reg = <0x4a003b20 0xc>;
-			ti,efuse-settings = <
-			/* uV   offset */
-			1060000 0x0
-			1160000 0x4
-			1210000 0x8
-			>;
-			ti,absolute-max-voltage-uv = <1500000>;
-		};
-
-	};
-
-	thermal_zones: thermal-zones {
-		#include "omap4-cpu-thermal.dtsi"
-		#include "omap5-gpu-thermal.dtsi"
-		#include "omap5-core-thermal.dtsi"
-		#include "dra7-dspeve-thermal.dtsi"
-		#include "dra7-iva-thermal.dtsi"
-	};
-
-};
-
-&cpu_thermal {
-	polling-delay = <500>; /* milliseconds */
-	coefficients = <0 2000>;
-};
-
-&gpu_thermal {
-	coefficients = <0 2000>;
-};
-
-&core_thermal {
-	coefficients = <0 2000>;
-};
-
-&dspeve_thermal {
-	coefficients = <0 2000>;
-};
-
-&iva_thermal {
-	coefficients = <0 2000>;
-};
-
-&cpu_crit {
-	temperature = <120000>; /* milli Celsius */
-};
-
-&core_crit {
-	temperature = <120000>; /* milli Celsius */
-};
-
-&gpu_crit {
-	temperature = <120000>; /* milli Celsius */
-};
-
-&dspeve_crit {
-	temperature = <120000>; /* milli Celsius */
-};
-
-&iva_crit {
-	temperature = <120000>; /* milli Celsius */
-};
-
-#include "dra7-l4.dtsi"
-#include "dra7xx-clocks.dtsi"
-
-&prm {
-	prm_dsp1: prm@400 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x400 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_ipu: prm@500 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x500 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_core: prm@700 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x700 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_iva: prm@f00 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0xf00 0x100>;
-	};
-
-	prm_dsp2: prm@1b00 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1b00 0x40>;
-		#reset-cells = <1>;
-	};
-
-	prm_eve1: prm@1b40 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1b40 0x40>;
-	};
-
-	prm_eve2: prm@1b80 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1b80 0x40>;
-	};
-
-	prm_eve3: prm@1bc0 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1bc0 0x40>;
-	};
-
-	prm_eve4: prm@1c00 {
-		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1c00 0x60>;
-	};
-};
diff --git a/arch/arm/boot/dts/dra72x.dtsi b/arch/arm/boot/dts/dra72x.dtsi
deleted file mode 100644
index f5762709c853..000000000000
--- a/arch/arm/boot/dts/dra72x.dtsi
+++ /dev/null
@@ -1,66 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on "omap4.dtsi"
- */
-
-#include "dra7.dtsi"
-
-/ {
-	compatible = "ti,dra722", "ti,dra72", "ti,dra7";
-
-	pmu {
-		compatible = "arm,cortex-a15-pmu";
-		interrupt-parent = <&wakeupgen>;
-		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-	};
-};
-
-&dss {
-	reg = <0x58000000 0x80>,
-	      <0x58004054 0x4>,
-	      <0x58004300 0x20>;
-	reg-names = "dss", "pll1_clkctrl", "pll1";
-
-	clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>,
-		 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 12>;
-	clock-names = "fck", "video1_clk";
-};
-
-&mailbox5 {
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		ti,mbox-tx = <6 2 2>;
-		ti,mbox-rx = <4 2 2>;
-		status = "disabled";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		ti,mbox-tx = <5 2 2>;
-		ti,mbox-rx = <1 2 2>;
-		status = "disabled";
-	};
-};
-
-&mailbox6 {
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		ti,mbox-tx = <6 2 2>;
-		ti,mbox-rx = <4 2 2>;
-		status = "disabled";
-	};
-};
-
-&pcie1_rc {
-	compatible = "ti,dra726-pcie-rc", "ti,dra7-pcie";
-};
-
-&pcie1_ep {
-	compatible = "ti,dra726-pcie-ep", "ti,dra7-pcie-ep";
-};
-
-&pcie2_rc {
-	compatible = "ti,dra726-pcie-rc", "ti,dra7-pcie";
-};
-
-&usb4_tm {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi
deleted file mode 100644
index d1b5b76bc5a8..000000000000
--- a/arch/arm/boot/dts/dra74x.dtsi
+++ /dev/null
@@ -1,146 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on "omap4.dtsi"
- */
-
-#include "dra7.dtsi"
-
-/ {
-	compatible = "ti,dra742", "ti,dra74", "ti,dra7";
-
-	cpus {
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a15";
-			reg = <1>;
-			operating-points-v2 = <&cpu0_opp_table>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-
-			/* cooling options */
-			#cooling-cells = <2>; /* min followed by max */
-
-			vbb-supply = <&abb_mpu>;
-		};
-	};
-
-	pmu {
-		compatible = "arm,cortex-a15-pmu";
-		interrupt-parent = <&wakeupgen>;
-		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
-	ocp {
-		dsp2_system: dsp_system@41500000 {
-			compatible = "syscon";
-			reg = <0x41500000 0x100>;
-		};
-
-		omap_dwc3_4: omap_dwc3_4@48940000 {
-			compatible = "ti,dwc3";
-			ti,hwmods = "usb_otg_ss4";
-			reg = <0x48940000 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			utmi-mode = <2>;
-			ranges;
-			status = "disabled";
-			usb4: usb@48950000 {
-				compatible = "snps,dwc3";
-				reg = <0x48950000 0x17000>;
-				interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "peripheral",
-						  "host",
-						  "otg";
-				maximum-speed = "high-speed";
-				dr_mode = "otg";
-			};
-		};
-
-		mmu0_dsp2: mmu@41501000 {
-			compatible = "ti,dra7-dsp-iommu";
-			reg = <0x41501000 0x100>;
-			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu0_dsp2";
-			#iommu-cells = <0>;
-			ti,syscon-mmuconfig = <&dsp2_system 0x0>;
-			status = "disabled";
-		};
-
-		mmu1_dsp2: mmu@41502000 {
-			compatible = "ti,dra7-dsp-iommu";
-			reg = <0x41502000 0x100>;
-			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu1_dsp2";
-			#iommu-cells = <0>;
-			ti,syscon-mmuconfig = <&dsp2_system 0x1>;
-			status = "disabled";
-		};
-	};
-};
-
-&cpu0_opp_table {
-	opp-shared;
-};
-
-&dss {
-	reg = <0x58000000 0x80>,
-	      <0x58004054 0x4>,
-	      <0x58004300 0x20>,
-	      <0x58009054 0x4>,
-	      <0x58009300 0x20>;
-	reg-names = "dss", "pll1_clkctrl", "pll1",
-		    "pll2_clkctrl", "pll2";
-
-	clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>,
-		 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 12>,
-		 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 13>;
-	clock-names = "fck", "video1_clk", "video2_clk";
-};
-
-&mailbox5 {
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		ti,mbox-tx = <6 2 2>;
-		ti,mbox-rx = <4 2 2>;
-		status = "disabled";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		ti,mbox-tx = <5 2 2>;
-		ti,mbox-rx = <1 2 2>;
-		status = "disabled";
-	};
-};
-
-&mailbox6 {
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		ti,mbox-tx = <6 2 2>;
-		ti,mbox-rx = <4 2 2>;
-		status = "disabled";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		ti,mbox-tx = <5 2 2>;
-		ti,mbox-rx = <1 2 2>;
-		status = "disabled";
-	};
-};
-
-&pcie1_rc {
-	compatible = "ti,dra746-pcie-rc", "ti,dra7-pcie";
-};
-
-&pcie1_ep {
-	compatible = "ti,dra746-pcie-ep", "ti,dra7-pcie-ep";
-};
-
-&pcie2_rc {
-	compatible = "ti,dra746-pcie-rc", "ti,dra7-pcie";
-};
diff --git a/arch/arm/boot/dts/efm32gg-dk3750.dts b/arch/arm/boot/dts/efm32gg-dk3750.dts
deleted file mode 100644
index adfa559a488b..000000000000
--- a/arch/arm/boot/dts/efm32gg-dk3750.dts
+++ /dev/null
@@ -1,88 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device tree for EFM32GG-DK3750 development board.
- *
- * Documentation available from
- * http://www.silabs.com/Support%20Documents/TechnicalDocs/efm32gg-dk3750-ug.pdf
- */
-
-/dts-v1/;
-#include "efm32gg.dtsi"
-
-/ {
-	model = "Energy Micro Giant Gecko Development Kit";
-	compatible = "efm32,dk3750";
-
-	chosen {
-		bootargs = "console=ttyefm4,115200 init=/linuxrc ignore_loglevel ihash_entries=64 dhash_entries=64 earlyprintk uclinux.physaddr=0x8c400000 root=/dev/mtdblock0";
-	};
-
-	memory@88000000 {
-		device_type = "memory";
-		reg = <0x88000000 0x400000>;
-	};
-
-	soc {
-		adc@40002000 {
-			status = "ok";
-		};
-
-		i2c@4000a000 {
-			energymicro,location = <3>;
-			status = "ok";
-
-			temp@48 {
-				compatible = "st,stds75";
-				reg = <0x48>;
-			};
-
-			eeprom@50 {
-				compatible = "microchip,24c02", "atmel,24c02";
-				reg = <0x50>;
-				pagesize = <16>;
-			};
-		};
-
-		spi0: spi@4000c000 { /* USART0 */
-			cs-gpios = <&gpio 68 1>; // E4
-			energymicro,location = <1>;
-			status = "ok";
-
-			microsd@0 {
-				compatible = "mmc-spi-slot";
-				spi-max-frequency = <100000>;
-				voltage-ranges = <3200 3400>;
-				broken-cd;
-				reg = <0>;
-			};
-		};
-
-		spi1: spi@4000c400 { /* USART1 */
-			cs-gpios = <&gpio 51 1>; // D3
-			energymicro,location = <1>;
-			status = "ok";
-
-			ks8851@0 {
-				compatible = "ks8851";
-				spi-max-frequency = <6000000>;
-				reg = <0>;
-				interrupt-parent = <&boardfpga>;
-				interrupts = <4>;
-			};
-		};
-
-		uart4: uart@4000e400 { /* UART1 */
-			energymicro,location = <2>;
-			status = "ok";
-		};
-
-		boardfpga: boardfpga@80000000 {
-			compatible = "efm32board";
-			reg = <0x80000000 0x400>;
-			irq-gpios = <&gpio 64 1>;
-			interrupt-controller;
-			#interrupt-cells = <1>;
-			status = "ok";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/efm32gg.dtsi b/arch/arm/boot/dts/efm32gg.dtsi
deleted file mode 100644
index 8a58e49144cc..000000000000
--- a/arch/arm/boot/dts/efm32gg.dtsi
+++ /dev/null
@@ -1,177 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device tree for Energy Micro EFM32 Giant Gecko SoC.
- *
- * Documentation available from
- * http://www.silabs.com/Support%20Documents/TechnicalDocs/EFM32GG-RM.pdf
- */
-
-#include "armv7-m.dtsi"
-#include "dt-bindings/clock/efm32-cmu.h"
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
-		spi0 = &spi0;
-		spi1 = &spi1;
-		spi2 = &spi2;
-	};
-
-	soc {
-		adc: adc@40002000 {
-			compatible = "energymicro,efm32-adc";
-			reg = <0x40002000 0x400>;
-			interrupts = <7>;
-			clocks = <&cmu clk_HFPERCLKADC0>;
-			status = "disabled";
-		};
-
-		gpio: gpio@40006000 {
-			compatible = "energymicro,efm32-gpio";
-			reg = <0x40006000 0x1000>;
-			interrupts = <1 11>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <1>;
-			clocks = <&cmu clk_HFPERCLKGPIO>;
-			status = "ok";
-		};
-
-		i2c0: i2c@4000a000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "energymicro,efm32-i2c";
-			reg = <0x4000a000 0x400>;
-			interrupts = <9>;
-			clocks = <&cmu clk_HFPERCLKI2C0>;
-			clock-frequency = <100000>;
-			status = "disabled";
-		};
-
-		i2c1: i2c@4000a400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "energymicro,efm32-i2c";
-			reg = <0x4000a400 0x400>;
-			interrupts = <10>;
-			clocks = <&cmu clk_HFPERCLKI2C1>;
-			clock-frequency = <100000>;
-			status = "disabled";
-		};
-
-		spi0: spi@4000c000 { /* USART0 */
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "energymicro,efm32-spi";
-			reg = <0x4000c000 0x400>;
-			interrupts = <3 4>;
-			clocks = <&cmu clk_HFPERCLKUSART0>;
-			status = "disabled";
-		};
-
-		spi1: spi@4000c400 { /* USART1 */
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "energymicro,efm32-spi";
-			reg = <0x4000c400 0x400>;
-			interrupts = <15 16>;
-			clocks = <&cmu clk_HFPERCLKUSART1>;
-			status = "disabled";
-		};
-
-		spi2: spi@4000c800 { /* USART2 */
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "energymicro,efm32-spi";
-			reg = <0x4000c800 0x400>;
-			interrupts = <18 19>;
-			clocks = <&cmu clk_HFPERCLKUSART2>;
-			status = "disabled";
-		};
-
-		uart0: uart@4000c000 { /* USART0 */
-			compatible = "energymicro,efm32-uart";
-			reg = <0x4000c000 0x400>;
-			interrupts = <3 4>;
-			clocks = <&cmu clk_HFPERCLKUSART0>;
-			status = "disabled";
-		};
-
-		uart1: uart@4000c400 { /* USART1 */
-			compatible = "energymicro,efm32-uart";
-			reg = <0x4000c400 0x400>;
-			interrupts = <15 16>;
-			clocks = <&cmu clk_HFPERCLKUSART1>;
-			status = "disabled";
-		};
-
-		uart2: uart@4000c800 { /* USART2 */
-			compatible = "energymicro,efm32-uart";
-			reg = <0x4000c800 0x400>;
-			interrupts = <18 19>;
-			clocks = <&cmu clk_HFPERCLKUSART2>;
-			status = "disabled";
-		};
-
-		uart3: uart@4000e000 { /* UART0 */
-			compatible = "energymicro,efm32-uart";
-			reg = <0x4000e000 0x400>;
-			interrupts = <20 21>;
-			clocks = <&cmu clk_HFPERCLKUART0>;
-			status = "disabled";
-		};
-
-		uart4: uart@4000e400 { /* UART1 */
-			compatible = "energymicro,efm32-uart";
-			reg = <0x4000e400 0x400>;
-			interrupts = <22 23>;
-			clocks = <&cmu clk_HFPERCLKUART1>;
-			status = "disabled";
-		};
-
-		timer0: timer@40010000 {
-			compatible = "energymicro,efm32-timer";
-			reg = <0x40010000 0x400>;
-			interrupts = <2>;
-			clocks = <&cmu clk_HFPERCLKTIMER0>;
-		};
-
-		timer1: timer@40010400 {
-			compatible = "energymicro,efm32-timer";
-			reg = <0x40010400 0x400>;
-			interrupts = <12>;
-			clocks = <&cmu clk_HFPERCLKTIMER1>;
-		};
-
-		timer2: timer@40010800 {
-			compatible = "energymicro,efm32-timer";
-			reg = <0x40010800 0x400>;
-			interrupts = <13>;
-			clocks = <&cmu clk_HFPERCLKTIMER2>;
-		};
-
-		timer3: timer@40010c00 {
-			compatible = "energymicro,efm32-timer";
-			reg = <0x40010c00 0x400>;
-			interrupts = <14>;
-			clocks = <&cmu clk_HFPERCLKTIMER3>;
-		};
-
-		cmu: cmu@400c8000 {
-			compatible = "efm32gg,cmu";
-			reg = <0x400c8000 0x400>;
-			interrupts = <32>;
-			#clock-cells = <1>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
deleted file mode 100644
index 7c39dd1c4d3a..000000000000
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ /dev/null
@@ -1,492 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Samsung's Exynos4210 based Trats board device tree source
- *
- * Copyright (c) 2012 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * Device tree source file for Samsung's Trats board which is based on
- * Samsung's Exynos4210 SoC.
- */
-
-/dts-v1/;
-#include "exynos4210.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Samsung Trats based on Exynos4210";
-	compatible = "samsung,trats", "samsung,exynos4210", "samsung,exynos4";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg =  <0x40000000 0x10000000
-			0x50000000 0x10000000
-			0x60000000 0x10000000
-			0x70000000 0x10000000>;
-	};
-
-	chosen {
-		bootargs = "root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
-		stdout-path = "serial2:115200n8";
-	};
-
-	regulators {
-		compatible = "simple-bus";
-
-		vemmc_reg: regulator-0 {
-			compatible = "regulator-fixed";
-			regulator-name = "VMEM_VDD_2.8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		tsp_reg: regulator-1 {
-			compatible = "regulator-fixed";
-			regulator-name = "TSP_FIXED_VOLTAGES";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		cam_af_28v_reg: regulator-2 {
-			compatible = "regulator-fixed";
-			regulator-name = "8M_AF_2.8V_EN";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		cam_io_en_reg: regulator-3 {
-			compatible = "regulator-fixed";
-			regulator-name = "CAM_IO_EN";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		cam_io_12v_reg: regulator-4 {
-			compatible = "regulator-fixed";
-			regulator-name = "8M_1.2V_EN";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		vt_core_15v_reg: regulator-5 {
-			compatible = "regulator-fixed";
-			regulator-name = "VT_CORE_1.5V";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		vol-down-key {
-			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
-			linux,code = <114>;
-			label = "volume down";
-			debounce-interval = <10>;
-		};
-
-		vol-up-key {
-			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
-			linux,code = <115>;
-			label = "volume up";
-			debounce-interval = <10>;
-		};
-
-		power-key {
-			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
-			linux,code = <116>;
-			label = "power";
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-
-		ok-key {
-			gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
-			linux,code = <352>;
-			label = "ok";
-			debounce-interval = <10>;
-		};
-	};
-
-	fixed-rate-clocks {
-		xxti {
-			compatible = "samsung,clock-xxti";
-			clock-frequency = <0>;
-		};
-
-		xusbxti {
-			compatible = "samsung,clock-xusbxti";
-			clock-frequency = <24000000>;
-		};
-	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			cooling-maps {
-				map0 {
-				     /* Corresponds to 800MHz at freq_table */
-				     cooling-device = <&cpu0 2 2>, <&cpu1 2 2>;
-				};
-				map1 {
-				     /* Corresponds to 200MHz at freq_table */
-				     cooling-device = <&cpu0 4 4>, <&cpu1 4 4>;
-			       };
-		       };
-		};
-	};
-
-};
-
-&camera {
-	pinctrl-names = "default";
-	pinctrl-0 = <>;
-	status = "okay";
-};
-
-&cpu0 {
-	cpu0-supply = <&varm_breg>;
-};
-
-&dsi_0 {
-	vddcore-supply = <&vusb_reg>;
-	vddio-supply = <&vmipi_reg>;
-	samsung,burst-clock-frequency = <500000000>;
-	samsung,esc-clock-frequency = <20000000>;
-	samsung,pll-clock-frequency = <24000000>;
-	status = "okay";
-
-	panel@0 {
-		reg = <0>;
-		compatible = "samsung,s6e8aa0";
-		vdd3-supply = <&vcclcd_reg>;
-		vci-supply = <&vlcd_reg>;
-		reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
-		power-on-delay= <50>;
-		reset-delay = <100>;
-		init-delay = <100>;
-		flip-horizontal;
-		flip-vertical;
-		panel-width-mm = <58>;
-		panel-height-mm = <103>;
-
-		display-timings {
-			timing-0 {
-				clock-frequency = <57153600>;
-				hactive = <720>;
-				vactive = <1280>;
-				hfront-porch = <5>;
-				hback-porch = <5>;
-				hsync-len = <5>;
-				vfront-porch = <13>;
-				vback-porch = <1>;
-				vsync-len = <2>;
-			};
-		};
-	};
-};
-
-&exynos_usbphy {
-	status = "okay";
-	vbus-supply = <&safe1_sreg>;
-};
-
-&fimc_0 {
-	status = "okay";
-	assigned-clocks = <&clock CLK_MOUT_FIMC0>,
-			  <&clock CLK_SCLK_FIMC0>;
-	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
-	assigned-clock-rates = <0>, <160000000>;
-};
-
-&fimc_1 {
-	status = "okay";
-	assigned-clocks = <&clock CLK_MOUT_FIMC1>,
-			  <&clock CLK_SCLK_FIMC1>;
-	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
-	assigned-clock-rates = <0>, <160000000>;
-};
-
-&fimc_2 {
-	status = "okay";
-	assigned-clocks = <&clock CLK_MOUT_FIMC2>,
-			  <&clock CLK_SCLK_FIMC2>;
-	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
-		assigned-clock-rates = <0>, <160000000>;
-};
-
-&fimc_3 {
-	status = "okay";
-	assigned-clocks = <&clock CLK_MOUT_FIMC3>,
-			  <&clock CLK_SCLK_FIMC3>;
-	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
-	assigned-clock-rates = <0>, <160000000>;
-};
-
-&fimd {
-	status = "okay";
-};
-
-&gpu {
-	status = "okay";
-};
-
-&hsotg {
-	vusb_d-supply = <&vusb_reg>;
-	vusb_a-supply = <&vusbdac_reg>;
-	dr_mode = "peripheral";
-	status = "okay";
-};
-
-&i2c_3 {
-	samsung,i2c-sda-delay = <100>;
-	samsung,i2c-slave-addr = <0x10>;
-	samsung,i2c-max-bus-freq = <400000>;
-	pinctrl-0 = <&i2c3_bus>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	mms114-touchscreen@48 {
-		compatible = "melfas,mms114";
-		reg = <0x48>;
-		interrupt-parent = <&gpx0>;
-		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
-		touchscreen-size-x = <720>;
-		touchscreen-size-y = <1280>;
-		avdd-supply = <&tsp_reg>;
-		vdd-supply = <&tsp_reg>;
-	};
-};
-
-&i2c_5 {
-	samsung,i2c-sda-delay = <100>;
-	samsung,i2c-slave-addr = <0x10>;
-	samsung,i2c-max-bus-freq = <100000>;
-	pinctrl-0 = <&i2c5_bus>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	max8997_pmic@66 {
-		compatible = "maxim,max8997-pmic";
-		interrupts-extended = <&gpx0 7 0>, <&gpx2 3 0>;
-
-		reg = <0x66>;
-		interrupt-parent = <&gpx0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
-
-		max8997,pmic-buck1-uses-gpio-dvs;
-		max8997,pmic-buck2-uses-gpio-dvs;
-		max8997,pmic-buck5-uses-gpio-dvs;
-
-		max8997,pmic-ignore-gpiodvs-side-effect;
-		max8997,pmic-buck125-default-dvs-idx = <0>;
-
-		max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>,
-						 <&gpx0 6 GPIO_ACTIVE_HIGH>,
-						 <&gpl0 0 GPIO_ACTIVE_HIGH>;
-
-		max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
-						 <1250000>, <1200000>,
-						 <1150000>, <1100000>,
-						 <1000000>, <950000>;
-
-		max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
-						 <950000>,  <900000>,
-						 <1100000>, <1000000>,
-						 <950000>,  <900000>;
-
-		max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
-						 <1200000>, <1200000>,
-						 <1200000>, <1200000>,
-						 <1200000>, <1200000>;
-
-		regulators {
-			valive_reg: LDO2 {
-			     regulator-name = "VALIVE_1.1V_C210";
-			     regulator-min-microvolt = <1100000>;
-			     regulator-max-microvolt = <1100000>;
-			     regulator-always-on;
-			};
-
-			vusb_reg: LDO3 {
-			     regulator-name = "VUSB_1.1V_C210";
-			     regulator-min-microvolt = <1100000>;
-			     regulator-max-microvolt = <1100000>;
-			};
-
-			vmipi_reg: LDO4 {
-			     regulator-name = "VMIPI_1.8V";
-			     regulator-min-microvolt = <1800000>;
-			     regulator-max-microvolt = <1800000>;
-			};
-
-			vpda_reg: LDO6 {
-			     regulator-name = "VCC_1.8V_PDA";
-			     regulator-min-microvolt = <1800000>;
-			     regulator-max-microvolt = <1800000>;
-			     regulator-always-on;
-			};
-
-			vcam_reg: LDO7 {
-			     regulator-name = "CAM_ISP_1.8V";
-			     regulator-min-microvolt = <1800000>;
-			     regulator-max-microvolt = <1800000>;
-			};
-
-			vusbdac_reg: LDO8 {
-			     regulator-name = "VUSB+VDAC_3.3V_C210";
-			     regulator-min-microvolt = <3300000>;
-			     regulator-max-microvolt = <3300000>;
-			};
-
-			vccpda_reg: LDO9 {
-			     regulator-name = "VCC_2.8V_PDA";
-			     regulator-min-microvolt = <2800000>;
-			     regulator-max-microvolt = <2800000>;
-			     regulator-always-on;
-			};
-
-			vpll_reg: LDO10 {
-			     regulator-name = "VPLL_1.1V_C210";
-			     regulator-min-microvolt = <1100000>;
-			     regulator-max-microvolt = <1100000>;
-			     regulator-always-on;
-			};
-
-			vtcam_reg: LDO12 {
-			     regulator-name = "VT_CAM_1.8V";
-			     regulator-min-microvolt = <1800000>;
-			     regulator-max-microvolt = <1800000>;
-			};
-
-			vcclcd_reg: LDO13 {
-			     regulator-name = "VCC_3.3V_LCD";
-			     regulator-min-microvolt = <3300000>;
-			     regulator-max-microvolt = <3300000>;
-			};
-
-			vlcd_reg: LDO15 {
-			     regulator-name = "VLCD_2.2V";
-			     regulator-min-microvolt = <2200000>;
-			     regulator-max-microvolt = <2200000>;
-			};
-
-			camsensor_reg: LDO16 {
-			     regulator-name = "CAM_SENSOR_IO_1.8V";
-			     regulator-min-microvolt = <1800000>;
-			     regulator-max-microvolt = <1800000>;
-			};
-
-			tflash_reg: LDO17 {
-			     regulator-name = "VTF_2.8V";
-			     regulator-min-microvolt = <2800000>;
-			     regulator-max-microvolt = <2800000>;
-			};
-
-			vddq_reg: LDO21 {
-			     regulator-name = "VDDQ_M1M2_1.2V";
-			     regulator-min-microvolt = <1200000>;
-			     regulator-max-microvolt = <1200000>;
-			     regulator-always-on;
-			};
-
-			varm_breg: BUCK1 {
-			     /*
-			      * HACK: The real name is VARM_1.2V_C210,
-			      * but exynos-cpufreq does not support
-			      * DT-based regulator lookup yet.
-			      */
-			     regulator-name = "vdd_arm";
-			     regulator-min-microvolt = <900000>;
-			     regulator-max-microvolt = <1350000>;
-			     regulator-always-on;
-			};
-
-			vint_breg: BUCK2 {
-			     regulator-name = "VINT_1.1V_C210";
-			     regulator-min-microvolt = <900000>;
-			     regulator-max-microvolt = <1100000>;
-			     regulator-always-on;
-			};
-
-			camisp_breg: BUCK4 {
-			     regulator-name = "CAM_ISP_CORE_1.2V";
-			     regulator-min-microvolt = <1200000>;
-			     regulator-max-microvolt = <1200000>;
-			};
-
-			vmem_breg: BUCK5 {
-			     regulator-name = "VMEM_1.2V_C210";
-			     regulator-min-microvolt = <1200000>;
-			     regulator-max-microvolt = <1200000>;
-			     regulator-always-on;
-			};
-
-			vccsub_breg: BUCK7 {
-			     regulator-name = "VCC_SUB_2.0V";
-			     regulator-min-microvolt = <2000000>;
-			     regulator-max-microvolt = <2000000>;
-			     regulator-always-on;
-			};
-
-			safe1_sreg: ESAFEOUT1 {
-			     regulator-name = "SAFEOUT1";
-			};
-
-			safe2_sreg: ESAFEOUT2 {
-			     regulator-name = "SAFEOUT2";
-			     regulator-boot-on;
-			};
-		};
-	};
-};
-
-&sdhci_0 {
-	bus-width = <8>;
-	non-removable;
-	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
-	pinctrl-names = "default";
-	vmmc-supply = <&vemmc_reg>;
-	status = "okay";
-};
-
-&sdhci_2 {
-	bus-width = <4>;
-	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
-	pinctrl-names = "default";
-	vmmc-supply = <&tflash_reg>;
-	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&serial_0 {
-	status = "okay";
-};
-
-&serial_1 {
-	status = "okay";
-};
-
-&serial_2 {
-	status = "okay";
-};
-
-&serial_3 {
-	status = "okay";
-};
-
-&tmu {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi b/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi
deleted file mode 100644
index 3a3b2fafefdd..000000000000
--- a/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi
+++ /dev/null
@@ -1,47 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device tree sources for Exynos4412 PPMU common device tree
- *
- * Copyright (C) 2015 Samsung Electronics
- * Author: Chanwoo Choi <cw00.choi@samsung.com>
- */
-
-&ppmu_dmc0 {
-       status = "okay";
-
-       events {
-	       ppmu_dmc0_3: ppmu-event3-dmc0 {
-		       event-name = "ppmu-event3-dmc0";
-	       };
-       };
-};
-
-&ppmu_dmc1 {
-       status = "okay";
-
-       events {
-	       ppmu_dmc1_3: ppmu-event3-dmc1 {
-		       event-name = "ppmu-event3-dmc1";
-	       };
-       };
-};
-
-&ppmu_leftbus {
-       status = "okay";
-
-       events {
-	       ppmu_leftbus_3: ppmu-event3-leftbus {
-		       event-name = "ppmu-event3-leftbus";
-	       };
-       };
-};
-
-&ppmu_rightbus {
-       status = "okay";
-
-       events {
-	       ppmu_rightbus_3: ppmu-event3-rightbus {
-		       event-name = "ppmu-event3-rightbus";
-	       };
-       };
-};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
deleted file mode 100644
index c3c2d85267da..000000000000
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
+++ /dev/null
@@ -1,89 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Hardkernel Odroid XU3 audio subsystem device tree source
- *
- * Copyright (c) 2015 Krzysztof Kozlowski
- * Copyright (c) 2014 Collabora Ltd.
- * Copyright (c) 2013 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- */
-
-#include <dt-bindings/sound/samsung-i2s.h>
-
-/ {
-	sound: sound {
-		compatible = "samsung,odroid-xu3-audio";
-		model = "Odroid-XU3";
-
-		samsung,audio-widgets =
-			"Headphone", "Headphone Jack",
-			"Speakers", "Speakers";
-		samsung,audio-routing =
-			"Headphone Jack", "HPL",
-			"Headphone Jack", "HPR",
-			"Headphone Jack", "MICBIAS",
-			"IN12", "Headphone Jack",
-			"Speakers", "SPKL",
-			"Speakers", "SPKR",
-			"I2S Playback", "Mixer DAI TX",
-			"HiFi Playback", "Mixer DAI TX",
-			"Mixer DAI RX", "HiFi Capture";
-
-		assigned-clocks = <&clock CLK_MOUT_EPLL>,
-				<&clock CLK_MOUT_MAU_EPLL>,
-				<&clock CLK_MOUT_USER_MAU_EPLL>,
-				<&clock_audss EXYNOS_MOUT_AUDSS>,
-				<&clock_audss EXYNOS_MOUT_I2S>,
-				<&clock_audss EXYNOS_DOUT_SRP>,
-				<&clock_audss EXYNOS_DOUT_AUD_BUS>,
-				<&clock_audss EXYNOS_DOUT_I2S>;
-
-		assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
-				<&clock CLK_MOUT_EPLL>,
-				<&clock CLK_MOUT_MAU_EPLL>,
-				<&clock CLK_MAU_EPLL>,
-				<&clock_audss EXYNOS_MOUT_AUDSS>;
-
-		assigned-clock-rates = <0>,
-				<0>,
-				<0>,
-				<0>,
-				<0>,
-				<196608001>,
-				<(196608002 / 2)>,
-				<196608000>;
-
-		cpu {
-			sound-dai = <&i2s0 0>, <&i2s0 1>;
-		};
-		codec {
-			sound-dai = <&hdmi>, <&max98090>;
-		};
-	};
-};
-
-&clock_audss {
-	assigned-clocks = <&clock_audss EXYNOS_DOUT_SRP>,
-			  <&clock CLK_FOUT_EPLL>;
-	assigned-clock-rates = <(196608000 / 256)>,
-			       <196608000>;
-};
-
-&hsi2c_5 {
-	status = "okay";
-	max98090: max98090@10 {
-		compatible = "maxim,max98090";
-		reg = <0x10>;
-		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_NONE>;
-		clocks = <&i2s0 CLK_I2S_CDCLK>;
-		clock-names = "mclk";
-		#sound-dai-cells = <0>;
-	};
-};
-
-&i2s0 {
-	status = "okay";
-	assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>;
-	assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>;
-};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts
deleted file mode 100644
index a31ca2ef750f..000000000000
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts
+++ /dev/null
@@ -1,47 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Hardkernel Odroid XU3-Lite board device tree source
- *
- * Copyright (c) 2015 Krzysztof Kozlowski
- * Copyright (c) 2014 Collabora Ltd.
- * Copyright (c) 2013 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- */
-
-/dts-v1/;
-#include "exynos5422-odroidxu3-common.dtsi"
-#include "exynos5422-odroidxu3-audio.dtsi"
-#include "exynos54xx-odroidxu-leds.dtsi"
-
-/ {
-	model = "Hardkernel Odroid XU3 Lite";
-	compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5";
-};
-
-&arm_a7_pmu {
-	status = "disabled";
-};
-
-&arm_a15_pmu {
-	status = "disabled";
-};
-
-&chipid {
-	samsung,asv-bin = <2>;
-};
-
-&pwm {
-	/*
-	 * PWM 0 -- fan
-	 * PWM 1 -- Green LED
-	 * PWM 2 -- Blue LED
-	 * PWM 3 -- on MIPI connector for backlight
-	 */
-	pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&usbdrd_dwc3_1 {
-	dr_mode = "peripheral";
-};
diff --git a/arch/arm/boot/dts/gemini/Makefile b/arch/arm/boot/dts/gemini/Makefile
new file mode 100644
index 000000000000..f9f63ce3eb49
--- /dev/null
+++ b/arch/arm/boot/dts/gemini/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_GEMINI) += \
+	gemini-dlink-dir-685.dtb \
+	gemini-dlink-dns-313.dtb \
+	gemini-nas4220b.dtb \
+	gemini-ns2502.dtb \
+	gemini-rut1xx.dtb \
+	gemini-sl93512r.dtb \
+	gemini-sq201.dtb \
+	gemini-ssi1328.dtb \
+	gemini-wbd111.dtb \
+	gemini-wbd222.dtb
diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
index e2030ba16512..396149664297 100644
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
@@ -61,9 +61,9 @@
 		#size-cells = <0>;
 
 		/* Collides with IDE pins, that's cool (we do not use them) */
-		gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 
@@ -119,13 +119,11 @@
 
 	/*
 	 * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
-	 * Since the platform has no temperature sensor, this is controlled
-	 * from userspace by using the hard disks S.M.A.R.T. temperature
 	 * sensor. It is turned on when the temperature exceeds 46 degrees
 	 * and turned off when the temperatures goes below 41 degrees
 	 * (celsius).
 	 */
-	gpio-fan {
+	fan0: gpio-fan {
 		compatible = "gpio-fan";
 		/* Collides with IDE */
 		gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
@@ -133,11 +131,45 @@
 		#cooling-cells = <2>;
 	};
 
+	thermal-zones {
+		chassis-thermal {
+			/* Poll every 20 seconds */
+			polling-delay = <20000>;
+			/* Poll every 2nd second when cooling */
+			polling-delay-passive = <2000>;
+			/*  Use the thermal sensor in the hard drive */
+			thermal-sensors = <&drive0>;
+
+			/* Tripping points from the fan.script in the rootfs */
+			trips {
+				alert: chassis-alert {
+					/* At 43 degrees turn on the fan */
+					temperature = <43000>;
+					hysteresis = <3000>;
+					type = "active";
+				};
+				crit: chassis-crit {
+					/* Just shut down at 60 degrees */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&alert>;
+					cooling-device = <&fan0 1 1>;
+				};
+			};
+		};
+	};
+
 	/*
 	 * The touchpad input is connected to a GPIO bit-banged
 	 * I2C bus.
 	 */
-	gpio-i2c {
+	i2c {
 		compatible = "i2c-gpio";
 		/* Collides with ICE */
 		sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
@@ -407,24 +439,6 @@
 
 		pci@50000000 {
 			status = "okay";
-			interrupt-map-mask = <0xf800 0 0 7>;
-			interrupt-map =
-				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-				<0x4800 0 0 2 &pci_intc 1>,
-				<0x4800 0 0 3 &pci_intc 2>,
-				<0x4800 0 0 4 &pci_intc 3>,
-				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-				<0x5000 0 0 2 &pci_intc 2>,
-				<0x5000 0 0 3 &pci_intc 3>,
-				<0x5000 0 0 4 &pci_intc 0>,
-				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-				<0x5800 0 0 2 &pci_intc 3>,
-				<0x5800 0 0 3 &pci_intc 0>,
-				<0x5800 0 0 4 &pci_intc 1>,
-				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-				<0x6000 0 0 2 &pci_intc 0>,
-				<0x6000 0 0 3 &pci_intc 1>,
-				<0x6000 0 0 4 &pci_intc 2>;
 		};
 
 		ethernet@60000000 {
@@ -443,15 +457,24 @@
 			};
 		};
 
-		ata@63000000 {
+		ide@63000000 {
 			status = "okay";
+
+			/*
+			 * This drive may have a temperature sensor with a
+			 * thermal zone we can use for thermal control of the
+			 * chassis temperature using the fan.
+			 */
+			drive0: ide-port@0 {
+				reg = <0>;
+				#thermal-sensor-cells = <0>;
+			};
 		};
 
 		display-controller@6a000000 {
 			status = "okay";
 
-			port@0 {
-				reg = <0>;
+			port {
 				display_out: endpoint {
 					remote-endpoint = <&panel_in>;
 				};
diff --git a/arch/arm/boot/dts/gemini-dlink-dns-313.dts b/arch/arm/boot/dts/gemini/gemini-dlink-dns-313.dts
index 360642a02a48..138c47e1ac1b 100644
--- a/arch/arm/boot/dts/gemini-dlink-dns-313.dts
+++ b/arch/arm/boot/dts/gemini/gemini-dlink-dns-313.dts
@@ -80,9 +80,18 @@
 		#cooling-cells = <2>;
 	};
 
+	/*
+	 * This is the type B USB connector on the device,
+	 * a GPIO-controlled USB VBUS detect
+	 */
+	usb1_phy: phy {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		#phy-cells = <0>;
+		vbus-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+	};
 
 	/* Global Mixed-Mode Technology G751 mounted on GPIO I2C */
-	gpio-i2c {
+	i2c {
 		compatible = "i2c-gpio";
 		sda-gpios = <&gpio0 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&gpio0 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
@@ -140,7 +149,7 @@
 		};
 	};
 
-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		/* Uses MDC and MDIO */
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
@@ -164,6 +173,8 @@
 			compatible = "cortina,gemini-flash", "jedec-flash";
 			status = "okay";
 			reg = <0x30000000 0x00080000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
 			/*
 			 * This "RedBoot" is the Storlink derivative.
@@ -297,8 +308,16 @@
 			};
 		};
 
-		ata@63000000 {
+		ide@63000000 {
 			status = "okay";
 		};
+
+		usb@69000000 {
+			status = "okay";
+			dr_mode = "peripheral";
+			usb-phy = <&usb1_phy>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_default_pins>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/gemini-nas4220b.dts b/arch/arm/boot/dts/gemini/gemini-nas4220b.dts
index 521714f38eed..6544c730340f 100644
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini/gemini-nas4220b.dts
@@ -62,7 +62,7 @@
 		};
 	};
 
-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
@@ -84,7 +84,7 @@
 			partitions {
 				compatible = "redboot-fis";
 				/* Eraseblock at 0xfe0000 */
-				fis-index-block = <0x1fc>;
+				fis-index-block = <0x7f>;
 			};
 		};
 
@@ -170,11 +170,11 @@
 			};
 		};
 
-		ata@63000000 {
+		ide@63000000 {
 			status = "okay";
 		};
 
-		ata@63400000 {
+		ide@63400000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/gemini/gemini-ns2502.dts b/arch/arm/boot/dts/gemini/gemini-ns2502.dts
new file mode 100644
index 000000000000..e6eeb35e8819
--- /dev/null
+++ b/arch/arm/boot/dts/gemini/gemini-ns2502.dts
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com>
+ * Device Tree file for Edimax NS 2502
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+
+/ {
+	model = "Edimax NS-2502";
+	compatible = "edimax,ns-2502", "cortina,gemini";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 128 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,19200n8";
+		stdout-path = &uart0;
+	};
+
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+			device_type = "ethernet-phy";
+		};
+	};
+};
+
+&ethernet {
+	status = "okay";
+	ethernet-port@0 {
+		phy-mode = "rgmii-id";
+		phy-handle = <&phy0>;
+	};
+};
+
+&flash {
+	status = "okay";
+	/* 8MB of flash */
+	reg = <0x30000000 0x00800000>;
+
+	pinctrl-names = "enabled", "disabled";
+	pinctrl-0 = <&pflash_default_pins>;
+	pinctrl-1 = <&pflash_disabled_pins>;
+
+	partitions {
+		compatible = "redboot-fis";
+		/* Eraseblock at 0x7e0000 */
+		fis-index-block = <0x3f>;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio0_default_pins>;
+};
+
+&ide0 {
+	status = "okay";
+};
+
+&ide1 {
+	status = "okay";
+};
+
+&sata {
+	cortina,gemini-ata-muxmode = <3>;
+	cortina,gemini-enable-sata-bridge;
+	status = "okay";
+};
+
+&syscon {
+	pinctrl {
+		/*
+		 * gpio0agrp cover line 0-4
+		 * gpio0bgrp cover line 5
+		 */
+		gpio0_default_pins: pinctrl-gpio0 {
+			    mux {
+				    function = "gpio0";
+				    groups = "gpio0agrp", "gpio0bgrp", "gpio0hgrp";
+			    };
+		};
+		pflash_disabled_pins: pinctrl-pflash-disabled {
+			mux {
+				function = "gpio0";
+				groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+					 "gpio0kgrp";
+			};
+		};
+		pinctrl-gmii {
+			mux {
+				function = "gmii";
+				groups = "gmii_gmac0_grp";
+				};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/gemini-rut1xx.dts b/arch/arm/boot/dts/gemini/gemini-rut1xx.dts
index 9611ddf06792..0ebda4efd9d0 100644
--- a/arch/arm/boot/dts/gemini-rut1xx.dts
+++ b/arch/arm/boot/dts/gemini/gemini-rut1xx.dts
@@ -56,7 +56,7 @@
 		};
 	};
 
-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
@@ -125,18 +125,6 @@
 			};
 		};
 
-		ethernet@60000000 {
-			status = "okay";
-
-			ethernet-port@0 {
-				phy-mode = "rgmii";
-				phy-handle = <&phy0>;
-			};
-			ethernet-port@1 {
-				/* Not used in this platform */
-			};
-		};
-
 		usb@68000000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/gemini-sl93512r.dts b/arch/arm/boot/dts/gemini/gemini-sl93512r.dts
index a98af0351906..91c19e8ebfe8 100644
--- a/arch/arm/boot/dts/gemini-sl93512r.dts
+++ b/arch/arm/boot/dts/gemini/gemini-sl93512r.dts
@@ -87,9 +87,9 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		/* Check pin collisions */
-		gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 		cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 
@@ -256,24 +256,6 @@
 
 		pci@50000000 {
 			status = "okay";
-			interrupt-map-mask = <0xf800 0 0 7>;
-			interrupt-map =
-				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-				<0x4800 0 0 2 &pci_intc 1>,
-				<0x4800 0 0 3 &pci_intc 2>,
-				<0x4800 0 0 4 &pci_intc 3>,
-				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-				<0x5000 0 0 2 &pci_intc 2>,
-				<0x5000 0 0 3 &pci_intc 3>,
-				<0x5000 0 0 4 &pci_intc 0>,
-				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-				<0x5800 0 0 2 &pci_intc 3>,
-				<0x5800 0 0 3 &pci_intc 0>,
-				<0x5800 0 0 4 &pci_intc 1>,
-				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-				<0x6000 0 0 2 &pci_intc 0>,
-				<0x6000 0 0 3 &pci_intc 1>,
-				<0x6000 0 0 4 &pci_intc 2>;
 		};
 
 		ethernet@60000000 {
@@ -293,11 +275,11 @@
 			};
 		};
 
-		ata@63000000 {
+		ide@63000000 {
 			status = "okay";
 		};
 
-		ata@63400000 {
+		ide@63400000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/gemini-sq201.dts b/arch/arm/boot/dts/gemini/gemini-sq201.dts
index 239dfacaae4d..d0efd76695da 100644
--- a/arch/arm/boot/dts/gemini-sq201.dts
+++ b/arch/arm/boot/dts/gemini/gemini-sq201.dts
@@ -72,9 +72,9 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		/* Check pin collisions */
-		gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 		cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 
@@ -252,24 +252,6 @@
 
 		pci@50000000 {
 			status = "okay";
-			interrupt-map-mask = <0xf800 0 0 7>;
-			interrupt-map =
-				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-				<0x4800 0 0 2 &pci_intc 1>,
-				<0x4800 0 0 3 &pci_intc 2>,
-				<0x4800 0 0 4 &pci_intc 3>,
-				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-				<0x5000 0 0 2 &pci_intc 2>,
-				<0x5000 0 0 3 &pci_intc 3>,
-				<0x5000 0 0 4 &pci_intc 0>,
-				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-				<0x5800 0 0 2 &pci_intc 3>,
-				<0x5800 0 0 3 &pci_intc 0>,
-				<0x5800 0 0 4 &pci_intc 1>,
-				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-				<0x6000 0 0 2 &pci_intc 0>,
-				<0x6000 0 0 3 &pci_intc 1>,
-				<0x6000 0 0 4 &pci_intc 2>;
 		};
 
 		ethernet@60000000 {
@@ -289,7 +271,7 @@
 			};
 		};
 
-		ata@63000000 {
+		ide@63000000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/gemini/gemini-ssi1328.dts b/arch/arm/boot/dts/gemini/gemini-ssi1328.dts
new file mode 100644
index 000000000000..42e85f07cf76
--- /dev/null
+++ b/arch/arm/boot/dts/gemini/gemini-ssi1328.dts
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com>
+ * Device Tree file for SSI 1328
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+
+/ {
+	model = "SSI 1328";
+	compatible = "ssi,1328", "cortina,gemini";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 128 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	aliases {
+		mdio-gpio0 = &mdio0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,19200n8 initrd=0x900000,9M";
+		stdout-path = &uart0;
+	};
+
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* LAN Marvell 88E1118 */
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+			device_type = "ethernet-phy";
+		};
+		/* WAN ICPlus IP101A */
+		phy1: ethernet-phy@2 {
+			reg = <2>;
+			device_type = "ethernet-phy";
+		};
+	};
+};
+
+&ethernet {
+	status = "okay";
+	ethernet-port@0 {
+		phy-mode = "rgmii";
+		phy-handle = <&phy0>;
+	};
+	ethernet-port@1 {
+		phy-mode = "rgmii";
+		phy-handle = <&phy1>;
+	};
+};
+
+&flash {
+	status = "okay";
+	/* 32MB of flash */
+	reg = <0x30000000 0x03200000>;
+
+	pinctrl-names = "enabled", "disabled";
+	pinctrl-0 = <&pflash_default_pins>;
+	pinctrl-1 = <&pflash_disabled_pins>;
+
+	partitions {
+		compatible = "redboot-fis";
+		/* Eraseblock at 0xfe0000 */
+		fis-index-block = <0x7F>;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio0_default_pins>;
+};
+
+&ide0 {
+	status = "okay";
+};
+
+&ide1 {
+	status = "okay";
+};
+
+&sata {
+	cortina,gemini-ata-muxmode = <0>;
+	cortina,gemini-enable-sata-bridge;
+	status = "okay";
+};
+
+&syscon {
+	pinctrl {
+		/*
+		 * gpio0agrp cover line 0-4
+		 * gpio0bgrp cover line 5
+		 */
+		gpio0_default_pins: pinctrl-gpio0 {
+			mux {
+				function = "gpio0";
+				groups = "gpio0agrp", "gpio0bgrp";
+			};
+		};
+		pflash_disabled_pins: pinctrl-pflash-disabled {
+			mux {
+				function = "gpio0";
+				groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+					 "gpio0kgrp";
+			};
+		};
+		pinctrl-gmii {
+			/* This platform use both the ethernet ports */
+			mux {
+				function = "gmii";
+				groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/gemini-wbd111.dts b/arch/arm/boot/dts/gemini/gemini-wbd111.dts
index 3a2761dd460f..3c88c59ab481 100644
--- a/arch/arm/boot/dts/gemini-wbd111.dts
+++ b/arch/arm/boot/dts/gemini/gemini-wbd111.dts
@@ -68,7 +68,7 @@
 		};
 	};
 
-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
@@ -87,33 +87,10 @@
 			/* 8MB of flash */
 			reg = <0x30000000 0x00800000>;
 
-			partition@0 {
-				label = "RedBoot";
-				reg = <0x00000000 0x00020000>;
-				read-only;
-			};
-			partition@20000 {
-				label = "kernel";
-				reg = <0x00020000 0x00100000>;
-			};
-			partition@120000 {
-				label = "rootfs";
-				reg = <0x00120000 0x006a0000>;
-			};
-			partition@7c0000 {
-				label = "VCTL";
-				reg = <0x007c0000 0x00010000>;
-				read-only;
-			};
-			partition@7d0000 {
-				label = "cfg";
-				reg = <0x007d0000 0x00010000>;
-				read-only;
-			};
-			partition@7e0000 {
-				label = "FIS";
-				reg = <0x007e0000 0x00010000>;
-				read-only;
+			partitions {
+				compatible = "redboot-fis";
+				/* Eraseblock at 0x7e0000 */
+				fis-index-block = <0x3f>;
 			};
 		};
 
@@ -140,24 +117,6 @@
 
 		pci@50000000 {
 			status = "okay";
-			interrupt-map-mask = <0xf800 0 0 7>;
-			interrupt-map =
-				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-				<0x4800 0 0 2 &pci_intc 1>,
-				<0x4800 0 0 3 &pci_intc 2>,
-				<0x4800 0 0 4 &pci_intc 3>,
-				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-				<0x5000 0 0 2 &pci_intc 2>,
-				<0x5000 0 0 3 &pci_intc 3>,
-				<0x5000 0 0 4 &pci_intc 0>,
-				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-				<0x5800 0 0 2 &pci_intc 3>,
-				<0x5800 0 0 3 &pci_intc 0>,
-				<0x5800 0 0 4 &pci_intc 1>,
-				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-				<0x6000 0 0 2 &pci_intc 0>,
-				<0x6000 0 0 3 &pci_intc 1>,
-				<0x6000 0 0 4 &pci_intc 2>;
 		};
 
 		ethernet@60000000 {
diff --git a/arch/arm/boot/dts/gemini-wbd222.dts b/arch/arm/boot/dts/gemini/gemini-wbd222.dts
index 52b4dbc0c072..ff72bbc4db3e 100644
--- a/arch/arm/boot/dts/gemini-wbd222.dts
+++ b/arch/arm/boot/dts/gemini/gemini-wbd222.dts
@@ -67,7 +67,7 @@
 		};
 	};
 
-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
@@ -91,33 +91,10 @@
 			/* 8MB of flash */
 			reg = <0x30000000 0x00800000>;
 
-			partition@0 {
-				label = "RedBoot";
-				reg = <0x00000000 0x00020000>;
-				read-only;
-			};
-			partition@20000 {
-				label = "kernel";
-				reg = <0x00020000 0x00100000>;
-			};
-			partition@120000 {
-				label = "rootfs";
-				reg = <0x00120000 0x006a0000>;
-			};
-			partition@7c0000 {
-				label = "VCTL";
-				reg = <0x007c0000 0x00010000>;
-				read-only;
-			};
-			partition@7d0000 {
-				label = "cfg";
-				reg = <0x007d0000 0x00010000>;
-				read-only;
-			};
-			partition@7e0000 {
-				label = "FIS";
-				reg = <0x007e0000 0x00010000>;
-				read-only;
+			partitions {
+				compatible = "redboot-fis";
+				/* Eraseblock at 0x7e0000 */
+				fis-index-block = <0x3f>;
 			};
 		};
 
@@ -151,24 +128,6 @@
 
 		pci@50000000 {
 			status = "okay";
-			interrupt-map-mask = <0xf800 0 0 7>;
-			interrupt-map =
-				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-				<0x4800 0 0 2 &pci_intc 1>,
-				<0x4800 0 0 3 &pci_intc 2>,
-				<0x4800 0 0 4 &pci_intc 3>,
-				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-				<0x5000 0 0 2 &pci_intc 2>,
-				<0x5000 0 0 3 &pci_intc 3>,
-				<0x5000 0 0 4 &pci_intc 0>,
-				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-				<0x5800 0 0 2 &pci_intc 3>,
-				<0x5800 0 0 3 &pci_intc 0>,
-				<0x5800 0 0 4 &pci_intc 1>,
-				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-				<0x6000 0 0 2 &pci_intc 0>,
-				<0x6000 0 0 3 &pci_intc 1>,
-				<0x6000 0 0 4 &pci_intc 2>;
 		};
 
 		ethernet@60000000 {
diff --git a/arch/arm/boot/dts/gemini.dtsi b/arch/arm/boot/dts/gemini/gemini.dtsi
index 8cf67b11751f..befe322bd7de 100644
--- a/arch/arm/boot/dts/gemini.dtsi
+++ b/arch/arm/boot/dts/gemini/gemini.dtsi
@@ -16,14 +16,12 @@
 		compatible = "simple-bus";
 		interrupt-parent = <&intcon>;
 
-		flash@30000000 {
+		flash: flash@30000000 {
 			compatible = "cortina,gemini-flash", "cfi-flash";
 			syscon = <&syscon>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pflash_default_pins>;
 			bank-width = <2>;
-			#address-cells = <1>;
-			#size-cells = <1>;
 			status = "disabled";
 		};
 
@@ -191,7 +189,7 @@
 		};
 
 		rtc@45000000 {
-			compatible = "cortina,gemini-rtc";
+			compatible = "cortina,gemini-rtc", "faraday,ftrtc010";
 			reg = <0x45000000 0x100>;
 			interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&syscon GEMINI_RESET_RTC>;
@@ -286,11 +284,31 @@
 			clock-names = "PCLK", "PCICLK";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pci_default_pins>;
+			device_type = "pci";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <1>;
 			status = "disabled";
 
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+				<0x4800 0 0 2 &pci_intc 1>,
+				<0x4800 0 0 3 &pci_intc 2>,
+				<0x4800 0 0 4 &pci_intc 3>,
+				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+				<0x5000 0 0 2 &pci_intc 2>,
+				<0x5000 0 0 3 &pci_intc 3>,
+				<0x5000 0 0 4 &pci_intc 0>,
+				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+				<0x5800 0 0 2 &pci_intc 3>,
+				<0x5800 0 0 3 &pci_intc 0>,
+				<0x5800 0 0 4 &pci_intc 1>,
+				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+				<0x6000 0 0 2 &pci_intc 0>,
+				<0x6000 0 0 3 &pci_intc 1>,
+				<0x6000 0 0 4 &pci_intc 2>;
+
 			bus-range = <0x00 0xff>;
 			/* PCI ranges mappings */
 			ranges =
@@ -321,7 +339,7 @@
 			};
 		};
 
-		ethernet@60000000 {
+		ethernet: ethernet@60000000 {
 			compatible = "cortina,gemini-ethernet";
 			reg = <0x60000000 0x4000>, /* Global registers, queue */
 			      <0x60004000 0x2000>, /* V-bit */
@@ -356,7 +374,15 @@
 			};
 		};
 
-		ata@63000000 {
+		crypto: crypto@62000000 {
+			compatible = "cortina,sl3516-crypto";
+			reg = <0x62000000 0x10000>;
+			interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+			resets = <&syscon GEMINI_RESET_SECURITY>;
+			clocks = <&syscon GEMINI_CLK_GATE_SECURITY>;
+		};
+
+		ide0: ide@63000000 {
 			compatible = "cortina,gemini-pata", "faraday,ftide010";
 			reg = <0x63000000 0x1000>;
 			interrupts = <4 IRQ_TYPE_EDGE_RISING>;
@@ -365,9 +391,11 @@
 			clock-names = "PCLK";
 			sata = <&sata>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
-		ata@63400000 {
+		ide1: ide@63400000 {
 			compatible = "cortina,gemini-pata", "faraday,ftide010";
 			reg = <0x63400000 0x1000>;
 			interrupts = <5 IRQ_TYPE_EDGE_RISING>;
@@ -376,6 +404,8 @@
 			clock-names = "PCLK";
 			sata = <&sata>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
 		dma-controller@67000000 {
@@ -405,13 +435,11 @@
 			clock-names = "PCLK", "TVE";
 			pinctrl-names = "default";
 			pinctrl-0 = <&tvc_default_pins>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			status = "disabled";
 		};
 
-		usb@68000000 {
-			compatible = "cortina,gemini-usb", "faraday,fotg210";
+		usb0: usb@68000000 {
+			compatible = "cortina,gemini-usb", "faraday,fotg200";
 			reg = <0x68000000 0x1000>;
 			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&syscon GEMINI_RESET_USB0>;
@@ -427,12 +455,14 @@
 			 */
 			pinctrl-names = "default";
 			pinctrl-0 = <&usb_default_pins>;
+			/* Default to host mode */
+			dr_mode = "host";
 			syscon = <&syscon>;
 			status = "disabled";
 		};
 
-		usb@69000000 {
-			compatible = "cortina,gemini-usb", "faraday,fotg210";
+		usb1: usb@69000000 {
+			compatible = "cortina,gemini-usb", "faraday,fotg200";
 			reg = <0x69000000 0x1000>;
 			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&syscon GEMINI_RESET_USB1>;
diff --git a/arch/arm/boot/dts/hisilicon/Makefile b/arch/arm/boot/dts/hisilicon/Makefile
new file mode 100644
index 000000000000..5ce0512c0010
--- /dev/null
+++ b/arch/arm/boot/dts/hisilicon/Makefile
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_HI3xxx) += \
+	hi3620-hi4511.dtb
+dtb-$(CONFIG_ARCH_HIP01) += \
+	hip01-ca9x2.dtb
+dtb-$(CONFIG_ARCH_HIP04) += \
+	hip04-d01.dtb
+dtb-$(CONFIG_ARCH_HISI) += \
+	hi3519-demb.dtb
+dtb-$(CONFIG_ARCH_HIX5HD2) += \
+	hisi-x5hd2-dkb.dtb
+dtb-$(CONFIG_ARCH_SD5203) += \
+	sd5203.dtb
diff --git a/arch/arm/boot/dts/hi3519-demb.dts b/arch/arm/boot/dts/hisilicon/hi3519-demb.dts
index 64f8ed126931..f473fa22e9ce 100644
--- a/arch/arm/boot/dts/hi3519-demb.dts
+++ b/arch/arm/boot/dts/hisilicon/hi3519-demb.dts
@@ -14,7 +14,7 @@
 		serial0 = &uart0;
 	};
 
-	memory {
+	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x40000000>;
 	};
diff --git a/arch/arm/boot/dts/hi3519.dtsi b/arch/arm/boot/dts/hisilicon/hi3519.dtsi
index 410409a0ed66..a42b71cdc5d7 100644
--- a/arch/arm/boot/dts/hi3519.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hi3519.dtsi
@@ -52,45 +52,45 @@
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12100000 0x1000>;
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_UART0_CLK>;
-			clock-names = "apb_pclk";
-			status = "disable";
+			clocks = <&crg HI3519_UART0_CLK>, <&crg HI3519_UART0_CLK>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
 		};
 
 		uart1: serial@12101000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12101000 0x1000>;
 			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_UART1_CLK>;
-			clock-names = "apb_pclk";
-			status = "disable";
+			clocks = <&crg HI3519_UART1_CLK>, <&crg HI3519_UART1_CLK>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
 		};
 
 		uart2: serial@12102000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12102000 0x1000>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_UART2_CLK>;
-			clock-names = "apb_pclk";
-			status = "disable";
+			clocks = <&crg HI3519_UART2_CLK>, <&crg HI3519_UART2_CLK>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
 		};
 
 		uart3: serial@12103000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12103000 0x1000>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_UART3_CLK>;
-			clock-names = "apb_pclk";
-			status = "disable";
+			clocks = <&crg HI3519_UART3_CLK>, <&crg HI3519_UART3_CLK>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
 		};
 
 		uart4: serial@12104000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12104000 0x1000>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_UART4_CLK>;
-			clock-names = "apb_pclk";
-			status = "disable";
+			clocks = <&crg HI3519_UART4_CLK>, <&crg HI3519_UART4_CLK>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
 		};
 
 		dual_timer0: timer@12000000 {
@@ -100,7 +100,7 @@
 			reg = <0x12000000 0x1000>;
 			clocks = <&clk_3m>;
 			clock-names = "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		dual_timer1: timer@12001000 {
@@ -110,7 +110,7 @@
 			reg = <0x12001000 0x1000>;
 			clocks = <&clk_3m>;
 			clock-names = "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		dual_timer2: timer@12002000 {
@@ -120,43 +120,43 @@
 			reg = <0x12002000 0x1000>;
 			clocks = <&clk_3m>;
 			clock-names = "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		spi_bus0: spi@12120000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x12120000 0x1000>;
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_SPI0_CLK>;
-			clock-names = "apb_pclk";
+			clocks = <&crg HI3519_SPI0_CLK>, <&crg HI3519_SPI0_CLK>;
+			clock-names = "sspclk", "apb_pclk";
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		spi_bus1: spi@12121000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x12121000 0x1000>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_SPI1_CLK>;
-			clock-names = "apb_pclk";
+			clocks = <&crg HI3519_SPI1_CLK>, <&crg HI3519_SPI1_CLK>;
+			clock-names = "sspclk", "apb_pclk";
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		spi_bus2: spi@12122000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x12122000 0x1000>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&crg HI3519_SPI2_CLK>;
-			clock-names = "apb_pclk";
+			clocks = <&crg HI3519_SPI2_CLK>, <&crg HI3519_SPI2_CLK>;
+			clock-names = "sspclk", "apb_pclk";
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		sysctrl: system-controller@12020000 {
diff --git a/arch/arm/boot/dts/hi3620-hi4511.dts b/arch/arm/boot/dts/hisilicon/hi3620-hi4511.dts
index 8c703c3f2fe0..f1c816a1d7cf 100644
--- a/arch/arm/boot/dts/hi3620-hi4511.dts
+++ b/arch/arm/boot/dts/hisilicon/hi3620-hi4511.dts
@@ -17,168 +17,168 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x20000000>;
 	};
 
-	amba {
+	amba-bus {
 		dual_timer0: dual_timer@800000 {
-			status = "ok";
+			status = "okay";
 		};
 
-		uart0: uart@b00000 {	/* console */
-			pinctrl-names = "default", "idle";
+		uart0: serial@b00000 {	/* console */
+			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
 			pinctrl-1 = <&uart0_pmx_idle &uart0_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
-		uart1: uart@b01000 { /* modem */
-			pinctrl-names = "default", "idle";
+		uart1: serial@b01000 { /* modem */
+			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
 			pinctrl-1 = <&uart1_pmx_idle &uart1_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
-		uart2: uart@b02000 { /* audience */
-			pinctrl-names = "default", "idle";
+		uart2: serial@b02000 { /* audience */
+			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
 			pinctrl-1 = <&uart2_pmx_idle &uart2_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
-		uart3: uart@b03000 {
-			pinctrl-names = "default", "idle";
+		uart3: serial@b03000 {
+			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
 			pinctrl-1 = <&uart3_pmx_idle &uart3_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
-		uart4: uart@b04000 {
-			pinctrl-names = "default", "idle";
+		uart4: serial@b04000 {
+			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
 			pinctrl-1 = <&uart4_pmx_idle &uart4_cfg_func>;
-			status = "ok";
+			status = "okay";
 		};
 
 		pmx0: pinmux@803000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&board_pmx_pins>;
 
-			board_pmx_pins: board_pmx_pins {
+			board_pmx_pins: board-pins {
 				pinctrl-single,pins = <
 					0x008 0x0	/* GPIO -- eFUSE_DOUT */
 					0x100 0x0	/* USIM_CLK & USIM_DATA (IOMG63) */
 				>;
 			};
-			uart0_pmx_func: uart0_pmx_func {
+			uart0_pmx_func: uart0-pins {
 				pinctrl-single,pins = <
 					0x0f0 0x0
 					0x0f4 0x0	/* UART0_RX & UART0_TX */
 				>;
 			};
-			uart0_pmx_idle: uart0_pmx_idle {
+			uart0_pmx_idle: uart0-idle-pins {
 				pinctrl-single,pins = <
 					/*0x0f0 0x1*/	/* UART0_CTS & UART0_RTS */
 					0x0f4 0x1	/* UART0_RX & UART0_TX */
 				>;
 			};
-			uart1_pmx_func: uart1_pmx_func {
+			uart1_pmx_func: uart1-pins {
 				pinctrl-single,pins = <
 					0x0f8 0x0	/* UART1_CTS & UART1_RTS (IOMG61) */
 					0x0fc 0x0	/* UART1_RX & UART1_TX (IOMG62) */
 				>;
 			};
-			uart1_pmx_idle: uart1_pmx_idle {
+			uart1_pmx_idle: uart1-idle-pins {
 				pinctrl-single,pins = <
 					0x0f8 0x1	/* GPIO (IOMG61) */
 					0x0fc 0x1	/* GPIO (IOMG62) */
 				>;
 			};
-			uart2_pmx_func: uart2_pmx_func {
+			uart2_pmx_func: uart2-pins {
 				pinctrl-single,pins = <
 					0x104 0x2	/* UART2_RXD (IOMG96) */
 					0x108 0x2	/* UART2_TXD (IOMG64) */
 				>;
 			};
-			uart2_pmx_idle: uart2_pmx_idle {
+			uart2_pmx_idle: uart2-idle-pins {
 				pinctrl-single,pins = <
 					0x104 0x1	/* GPIO (IOMG96) */
 					0x108 0x1	/* GPIO (IOMG64) */
 				>;
 			};
-			uart3_pmx_func: uart3_pmx_func {
+			uart3_pmx_func: uart3-pins {
 				pinctrl-single,pins = <
 					0x160 0x2	/* UART3_CTS & UART3_RTS (IOMG85) */
 					0x164 0x2	/* UART3_RXD & UART3_TXD (IOMG86) */
 				>;
 			};
-			uart3_pmx_idle: uart3_pmx_idle {
+			uart3_pmx_idle: uart3-idle-pins {
 				pinctrl-single,pins = <
 					0x160 0x1	/* GPIO (IOMG85) */
 					0x164 0x1	/* GPIO (IOMG86) */
 				>;
 			};
-			uart4_pmx_func: uart4_pmx_func {
+			uart4_pmx_func: uart4-pins {
 				pinctrl-single,pins = <
 					0x168 0x0	/* UART4_CTS & UART4_RTS (IOMG87) */
 					0x16c 0x0	/* UART4_RXD (IOMG88) */
 					0x170 0x0	/* UART4_TXD (IOMG93) */
 				>;
 			};
-			uart4_pmx_idle: uart4_pmx_idle {
+			uart4_pmx_idle: uart4-idle-pins {
 				pinctrl-single,pins = <
 					0x168 0x1	/* GPIO (IOMG87) */
 					0x16c 0x1	/* GPIO (IOMG88) */
 					0x170 0x1	/* GPIO (IOMG93) */
 				>;
 			};
-			i2c0_pmx_func: i2c0_pmx_func {
+			i2c0_pmx_func: i2c0-pins {
 				pinctrl-single,pins = <
 					0x0b4 0x0	/* I2C0_SCL & I2C0_SDA (IOMG45) */
 				>;
 			};
-			i2c0_pmx_idle: i2c0_pmx_idle {
+			i2c0_pmx_idle: i2c0-idle-pins {
 				pinctrl-single,pins = <
 					0x0b4 0x1	/* GPIO (IOMG45) */
 				>;
 			};
-			i2c1_pmx_func: i2c1_pmx_func {
+			i2c1_pmx_func: i2c1-pins {
 				pinctrl-single,pins = <
 					0x0b8 0x0	/* I2C1_SCL & I2C1_SDA (IOMG46) */
 				>;
 			};
-			i2c1_pmx_idle: i2c1_pmx_idle {
+			i2c1_pmx_idle: i2c1-idle-pins {
 				pinctrl-single,pins = <
 					0x0b8 0x1	/* GPIO (IOMG46) */
 				>;
 			};
-			i2c2_pmx_func: i2c2_pmx_func {
+			i2c2_pmx_func: i2c2-pins {
 				pinctrl-single,pins = <
 					0x068 0x0	/* I2C2_SCL (IOMG26) */
 					0x06c 0x0	/* I2C2_SDA (IOMG27) */
 				>;
 			};
-			i2c2_pmx_idle: i2c2_pmx_idle {
+			i2c2_pmx_idle: i2c2-idle-pins {
 				pinctrl-single,pins = <
 					0x068 0x1	/* GPIO (IOMG26) */
 					0x06c 0x1	/* GPIO (IOMG27) */
 				>;
 			};
-			i2c3_pmx_func: i2c3_pmx_func {
+			i2c3_pmx_func: i2c3-pins {
 				pinctrl-single,pins = <
 					0x050 0x2	/* I2C3_SCL (IOMG20) */
 					0x054 0x2	/* I2C3_SDA (IOMG21) */
 				>;
 			};
-			i2c3_pmx_idle: i2c3_pmx_idle {
+			i2c3_pmx_idle: i2c3-idle-pins {
 				pinctrl-single,pins = <
 					0x050 0x1	/* GPIO (IOMG20) */
 					0x054 0x1	/* GPIO (IOMG21) */
 				>;
 			};
-			spi0_pmx_func: spi0_pmx_func {
+			spi0_pmx_func: spi0-pins {
 				pinctrl-single,pins = <
 					0x0d4 0x0	/* SPI0_CLK/SPI0_DI/SPI0_DO (IOMG53) */
 					0x0d8 0x0	/* SPI0_CS0 (IOMG54) */
@@ -187,7 +187,7 @@
 					0x0e4 0x0	/* SPI0_CS3 (IOMG57) */
 				>;
 			};
-			spi0_pmx_idle: spi0_pmx_idle {
+			spi0_pmx_idle: spi0-idle-pins {
 				pinctrl-single,pins = <
 					0x0d4 0x1	/* GPIO (IOMG53) */
 					0x0d8 0x1	/* GPIO (IOMG54) */
@@ -196,21 +196,21 @@
 					0x0e4 0x1	/* GPIO (IOMG57) */
 				>;
 			};
-			spi1_pmx_func: spi1_pmx_func {
+			spi1_pmx_func: spi1-pins {
 				pinctrl-single,pins = <
 					0x184 0x0	/* SPI1_CLK/SPI1_DI (IOMG98) */
 					0x0e8 0x0	/* SPI1_DO (IOMG58) */
 					0x0ec 0x0	/* SPI1_CS (IOMG95) */
 				>;
 			};
-			spi1_pmx_idle: spi1_pmx_idle {
+			spi1_pmx_idle: spi1-idle-pins {
 				pinctrl-single,pins = <
 					0x184 0x1	/* GPIO (IOMG98) */
 					0x0e8 0x1	/* GPIO (IOMG58) */
 					0x0ec 0x1	/* GPIO (IOMG95) */
 				>;
 			};
-			kpc_pmx_func: kpc_pmx_func {
+			kpc_pmx_func: kpc-pins {
 				pinctrl-single,pins = <
 					0x12c 0x0	/* KEY_IN0 (IOMG73) */
 					0x130 0x0	/* KEY_IN1 (IOMG74) */
@@ -220,7 +220,7 @@
 					0x114 0x0	/* KEY_OUT2 (IOMG67) */
 				>;
 			};
-			kpc_pmx_idle: kpc_pmx_idle {
+			kpc_pmx_idle: kpc-idle-pins {
 				pinctrl-single,pins = <
 					0x12c 0x1	/* GPIO (IOMG73) */
 					0x130 0x1	/* GPIO (IOMG74) */
@@ -230,13 +230,13 @@
 					0x114 0x1	/* GPIO (IOMG67) */
 				>;
 			};
-			gpio_key_func: gpio_key_func {
+			gpio_key_func: gpio-key-pins {
 				pinctrl-single,pins = <
 					0x10c 0x1	/* KEY_OUT0/GPIO (IOMG65) */
 					0x130 0x1	/* KEY_IN1/GPIO (IOMG74) */
 				>;
 			};
-			emmc_pmx_func: emmc_pmx_func {
+			emmc_pmx_func: emmc-pins {
 				pinctrl-single,pins = <
 					0x030 0x2	/* eMMC_CMD/eMMC_CLK (IOMG12) */
 					0x018 0x0	/* NAND_CS3_N (IOMG6) */
@@ -245,7 +245,7 @@
 					0x02c 0x2	/* eMMC_DATA[0:7] (IOMG10) */
 				>;
 			};
-			emmc_pmx_idle: emmc_pmx_idle {
+			emmc_pmx_idle: emmc-idle-pins {
 				pinctrl-single,pins = <
 					0x030 0x0	/* GPIO (IOMG12) */
 					0x018 0x1	/* GPIO (IOMG6) */
@@ -254,19 +254,19 @@
 					0x02c 0x1	/* GPIO (IOMG10) */
 				>;
 			};
-			sd_pmx_func: sd_pmx_func {
+			sd_pmx_func: sd-pins {
 				pinctrl-single,pins = <
 					0x0bc 0x0	/* SD_CLK/SD_CMD/SD_DATA0/SD_DATA1/SD_DATA2 (IOMG47) */
 					0x0c0 0x0	/* SD_DATA3 (IOMG48) */
 				>;
 			};
-			sd_pmx_idle: sd_pmx_idle {
+			sd_pmx_idle: sd-idle-pins {
 				pinctrl-single,pins = <
 					0x0bc 0x1	/* GPIO (IOMG47) */
 					0x0c0 0x1	/* GPIO (IOMG48) */
 				>;
 			};
-			nand_pmx_func: nand_pmx_func {
+			nand_pmx_func: nand-pins {
 				pinctrl-single,pins = <
 					0x00c 0x0	/* NAND_ALE/NAND_CLE/.../NAND_DATA[0:7] (IOMG3) */
 					0x010 0x0	/* NAND_CS1_N (IOMG4) */
@@ -279,7 +279,7 @@
 					0x02c 0x0	/* NAND_DATA[8:15] (IOMG10) */
 				>;
 			};
-			nand_pmx_idle: nand_pmx_idle {
+			nand_pmx_idle: nand-idle-pins {
 				pinctrl-single,pins = <
 					0x00c 0x1	/* GPIO (IOMG3) */
 					0x010 0x1	/* GPIO (IOMG4) */
@@ -292,17 +292,17 @@
 					0x02c 0x1	/* GPIO (IOMG10) */
 				>;
 			};
-			sdio_pmx_func: sdio_pmx_func {
+			sdio_pmx_func: sdio-pins {
 				pinctrl-single,pins = <
 					0x0c4 0x0	/* SDIO_CLK/SDIO_CMD/SDIO_DATA[0:3] (IOMG49) */
 				>;
 			};
-			sdio_pmx_idle: sdio_pmx_idle {
+			sdio_pmx_idle: sdio-idle-pins {
 				pinctrl-single,pins = <
 					0x0c4 0x1	/* GPIO (IOMG49) */
 				>;
 			};
-			audio_out_pmx_func: audio_out_pmx_func {
+			audio_out_pmx_func: audio-out-pins {
 				pinctrl-single,pins = <
 					0x0f0 0x1	/* GPIO (IOMG59), audio spk & earphone */
 				>;
@@ -314,7 +314,7 @@
 			pinctrl-0 = <	&board_pu_pins &board_pd_pins &board_pd_ps_pins
 					&board_np_pins &board_ps_pins &kpc_cfg_func
 					&audio_out_cfg_func>;
-			board_pu_pins: board_pu_pins {
+			board_pu_pins: board-pu-pins {
 				pinctrl-single,pins = <
 					0x014 0		/* GPIO_158 (IOCFG2) */
 					0x018 0		/* GPIO_159 (IOCFG3) */
@@ -324,7 +324,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 			};
-			board_pd_pins: board_pd_pins {
+			board_pd_pins: board-pd-pins {
 				pinctrl-single,pins = <
 					0x038 0		/* eFUSE_DOUT (IOCFG11) */
 					0x150 0		/* ISP_GPIO8 (IOCFG93) */
@@ -333,7 +333,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			board_pd_ps_pins: board_pd_ps_pins {
+			board_pd_ps_pins: board-pd-ps-pins {
 				pinctrl-single,pins = <
 					0x2d8 0		/* CLK_OUT0 (IOCFG190) */
 					0x004 0		/* PMU_SPI_DATA (IOCFG192) */
@@ -342,21 +342,21 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			board_np_pins: board_np_pins {
+			board_np_pins: board-np-pins {
 				pinctrl-single,pins = <
 					0x24c 0		/* KEYPAD_OUT7 (IOCFG155) */
 				>;
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			board_ps_pins: board_ps_pins {
+			board_ps_pins: board-ps-pins {
 				pinctrl-single,pins = <
 					0x000 0		/* PMU_SPI_CLK (IOCFG191) */
 					0x008 0		/* PMU_SPI_CS_N (IOCFG193) */
 				>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			uart0_cfg_func: uart0_cfg_func {
+			uart0_cfg_func: uart0-cfg-pins {
 				pinctrl-single,pins = <
 					0x208 0		/* UART0_RXD (IOCFG138) */
 					0x20c 0		/* UART0_TXD (IOCFG139) */
@@ -364,7 +364,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart0_cfg_idle: uart0_cfg_idle {
+			uart0_cfg_idle: uart0-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x208 0		/* UART0_RXD (IOCFG138) */
 					0x20c 0		/* UART0_TXD (IOCFG139) */
@@ -372,7 +372,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart1_cfg_func: uart1_cfg_func {
+			uart1_cfg_func: uart1-cfg-pins {
 				pinctrl-single,pins = <
 					0x210 0		/* UART1_CTS (IOCFG140) */
 					0x214 0		/* UART1_RTS (IOCFG141) */
@@ -382,7 +382,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart1_cfg_idle: uart1_cfg_idle {
+			uart1_cfg_idle: uart1-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x210 0		/* UART1_CTS (IOCFG140) */
 					0x214 0		/* UART1_RTS (IOCFG141) */
@@ -392,7 +392,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart2_cfg_func: uart2_cfg_func {
+			uart2_cfg_func: uart2-cfg-pins {
 				pinctrl-single,pins = <
 					0x220 0		/* UART2_CTS (IOCFG144) */
 					0x224 0		/* UART2_RTS (IOCFG145) */
@@ -402,7 +402,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart2_cfg_idle: uart2_cfg_idle {
+			uart2_cfg_idle: uart2-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x220 0		/* GPIO (IOCFG144) */
 					0x224 0		/* GPIO (IOCFG145) */
@@ -412,7 +412,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart3_cfg_func: uart3_cfg_func {
+			uart3_cfg_func: uart3-cfg-pins {
 				pinctrl-single,pins = <
 					0x294 0		/* UART3_CTS (IOCFG173) */
 					0x298 0		/* UART3_RTS (IOCFG174) */
@@ -422,7 +422,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart3_cfg_idle: uart3_cfg_idle {
+			uart3_cfg_idle: uart3-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x294 0		/* UART3_CTS (IOCFG173) */
 					0x298 0		/* UART3_RTS (IOCFG174) */
@@ -432,7 +432,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart4_cfg_func: uart4_cfg_func {
+			uart4_cfg_func: uart4-cfg-pins {
 				pinctrl-single,pins = <
 					0x2a4 0		/* UART4_CTS (IOCFG177) */
 					0x2a8 0		/* UART4_RTS (IOCFG178) */
@@ -442,7 +442,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			i2c0_cfg_func: i2c0_cfg_func {
+			i2c0_cfg_func: i2c0-cfg-pins {
 				pinctrl-single,pins = <
 					0x17c 0		/* I2C0_SCL (IOCFG103) */
 					0x180 0		/* I2C0_SDA (IOCFG104) */
@@ -451,7 +451,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			i2c1_cfg_func: i2c1_cfg_func {
+			i2c1_cfg_func: i2c1-cfg-pins {
 				pinctrl-single,pins = <
 					0x184 0		/* I2C1_SCL (IOCFG105) */
 					0x188 0		/* I2C1_SDA (IOCFG106) */
@@ -460,7 +460,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			i2c2_cfg_func: i2c2_cfg_func {
+			i2c2_cfg_func: i2c2-cfg-pins {
 				pinctrl-single,pins = <
 					0x118 0		/* I2C2_SCL (IOCFG79) */
 					0x11c 0		/* I2C2_SDA (IOCFG80) */
@@ -469,7 +469,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			i2c3_cfg_func: i2c3_cfg_func {
+			i2c3_cfg_func: i2c3-cfg-pins {
 				pinctrl-single,pins = <
 					0x100 0		/* I2C3_SCL (IOCFG73) */
 					0x104 0		/* I2C3_SDA (IOCFG74) */
@@ -478,7 +478,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi0_cfg_func1: spi0_cfg_func1 {
+			spi0_cfg_func1: spi0-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x1d4 0		/* SPI0_CLK (IOCFG125) */
 					0x1d8 0		/* SPI0_DI (IOCFG126) */
@@ -488,7 +488,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi0_cfg_func2: spi0_cfg_func2 {
+			spi0_cfg_func2: spi0-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x1e0 0		/* SPI0_CS0 (IOCFG128) */
 					0x1e4 0		/* SPI0_CS1 (IOCFG129) */
@@ -499,7 +499,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi1_cfg_func1: spi1_cfg_func1 {
+			spi1_cfg_func1: spi1-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x1f0 0		/* SPI1_CLK (IOCFG132) */
 					0x1f4 0		/* SPI1_DI (IOCFG133) */
@@ -509,7 +509,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi1_cfg_func2: spi1_cfg_func2 {
+			spi1_cfg_func2: spi1-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x1fc 0		/* SPI1_CS (IOCFG135) */
 				>;
@@ -517,7 +517,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			kpc_cfg_func: kpc_cfg_func {
+			kpc_cfg_func: kpc-cfg-pins {
 				pinctrl-single,pins = <
 					0x250 0		/* KEY_IN0 (IOCFG156) */
 					0x254 0		/* KEY_IN1 (IOCFG157) */
@@ -529,7 +529,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			emmc_cfg_func: emmc_cfg_func {
+			emmc_cfg_func: emmc-cfg-pins {
 				pinctrl-single,pins = <
 					0x0ac 0		/* eMMC_CMD (IOCFG40) */
 					0x0b0 0		/* eMMC_CLK (IOCFG41) */
@@ -549,7 +549,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			sd_cfg_func1: sd_cfg_func1 {
+			sd_cfg_func1: sd-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x18c 0		/* SD_CLK (IOCFG107) */
 					0x190 0		/* SD_CMD (IOCFG108) */
@@ -558,7 +558,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			sd_cfg_func2: sd_cfg_func2 {
+			sd_cfg_func2: sd-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x194 0		/* SD_DATA0 (IOCFG109) */
 					0x198 0		/* SD_DATA1 (IOCFG110) */
@@ -569,7 +569,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x70 0xf0>;
 			};
-			nand_cfg_func1: nand_cfg_func1 {
+			nand_cfg_func1: nand-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x03c 0		/* NAND_ALE (IOCFG12) */
 					0x040 0		/* NAND_CLE (IOCFG13) */
@@ -594,7 +594,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			nand_cfg_func2: nand_cfg_func2 {
+			nand_cfg_func2: nand-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x044 0		/* NAND_RE_N (IOCFG14) */
 					0x048 0		/* NAND_WE_N (IOCFG15) */
@@ -611,7 +611,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			sdio_cfg_func: sdio_cfg_func {
+			sdio_cfg_func: sdio-cfg-pins {
 				pinctrl-single,pins = <
 					0x1a4 0		/* SDIO0_CLK (IOCG113) */
 					0x1a8 0		/* SDIO0_CMD (IOCG114) */
@@ -624,7 +624,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			audio_out_cfg_func: audio_out_cfg_func {
+			audio_out_cfg_func: audio-out-cfg-pins {
 				pinctrl-single,pins = <
 					0x200 0		/* GPIO (IOCFG136) */
 					0x204 0		/* GPIO (IOCFG137) */
diff --git a/arch/arm/boot/dts/hi3620.dtsi b/arch/arm/boot/dts/hisilicon/hi3620.dtsi
index 9c207a690df5..a254ec009296 100644
--- a/arch/arm/boot/dts/hi3620.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hi3620.dtsi
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Hisilicon Ltd. Hi3620 SoC
+ * HiSilicon Ltd. Hi3620 SoC
  *
- * Copyright (C) 2012-2013 Hisilicon Ltd.
+ * Copyright (C) 2012-2013 HiSilicon Ltd.
  * Copyright (C) 2012-2013 Linaro Ltd.
  *
  * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
@@ -63,7 +63,7 @@
 		};
 	};
 
-	amba {
+	amba-bus {
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -71,7 +71,7 @@
 		interrupt-parent = <&gic>;
 		ranges = <0 0xfc000000 0x2000000>;
 
-		L2: l2-cache {
+		L2: cache-controller {
 			compatible = "arm,pl310-cache";
 			reg = <0x100000 0x100000>;
 			interrupts = <0 15 4>;
@@ -89,7 +89,7 @@
 		};
 
 		sysctrl: system-controller@802000 {
-			compatible = "hisilicon,sysctrl";
+			compatible = "hisilicon,sysctrl", "syscon";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x802000 0x1000>;
@@ -111,8 +111,10 @@
 			reg = <0x800000 0x1000>;
 			/* timer00 & timer01 */
 			interrupts = <0 0 4>, <0 1 4>;
-			clocks = <&clock HI3620_TIMER0_MUX>, <&clock HI3620_TIMER1_MUX>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_TIMER0_MUX>,
+				 <&clock HI3620_TIMER1_MUX>,
+				 <&clock HI3620_TIMER0_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -121,8 +123,10 @@
 			reg = <0x801000 0x1000>;
 			/* timer10 & timer11 */
 			interrupts = <0 2 4>, <0 3 4>;
-			clocks = <&clock HI3620_TIMER2_MUX>, <&clock HI3620_TIMER3_MUX>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_TIMER2_MUX>,
+				 <&clock HI3620_TIMER3_MUX>,
+				 <&clock HI3620_TIMER2_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -131,8 +135,10 @@
 			reg = <0xa01000 0x1000>;
 			/* timer20 & timer21 */
 			interrupts = <0 4 4>, <0 5 4>;
-			clocks = <&clock HI3620_TIMER4_MUX>, <&clock HI3620_TIMER5_MUX>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_TIMER4_MUX>,
+				 <&clock HI3620_TIMER5_MUX>,
+				 <&clock HI3620_TIMER4_MUX>;
+			clock-names = "timer0lck", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -141,8 +147,10 @@
 			reg = <0xa02000 0x1000>;
 			/* timer30 & timer31 */
 			interrupts = <0 6 4>, <0 7 4>;
-			clocks = <&clock HI3620_TIMER6_MUX>, <&clock HI3620_TIMER7_MUX>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_TIMER6_MUX>,
+				 <&clock HI3620_TIMER7_MUX>,
+				 <&clock HI3620_TIMER6_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -151,8 +159,10 @@
 			reg = <0xa03000 0x1000>;
 			/* timer40 & timer41 */
 			interrupts = <0 96 4>, <0 97 4>;
-			clocks = <&clock HI3620_TIMER8_MUX>, <&clock HI3620_TIMER9_MUX>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_TIMER8_MUX>,
+				 <&clock HI3620_TIMER9_MUX>,
+				 <&clock HI3620_TIMER8_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -162,48 +172,48 @@
 			interrupts = <1 13 0xf01>;
 		};
 
-		uart0: uart@b00000 {
+		uart0: serial@b00000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0xb00000 0x1000>;
 			interrupts = <0 20 4>;
-			clocks = <&clock HI3620_UARTCLK0>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_UARTCLK0>, <&clock HI3620_UARTCLK0>;
+			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
 
-		uart1: uart@b01000 {
+		uart1: serial@b01000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0xb01000 0x1000>;
 			interrupts = <0 21 4>;
-			clocks = <&clock HI3620_UARTCLK1>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_UARTCLK1>, <&clock HI3620_UARTCLK1>;
+			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
 
-		uart2: uart@b02000 {
+		uart2: serial@b02000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0xb02000 0x1000>;
 			interrupts = <0 22 4>;
-			clocks = <&clock HI3620_UARTCLK2>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_UARTCLK2>, <&clock HI3620_UARTCLK2>;
+			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
 
-		uart3: uart@b03000 {
+		uart3: serial@b03000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0xb03000 0x1000>;
 			interrupts = <0 23 4>;
-			clocks = <&clock HI3620_UARTCLK3>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_UARTCLK3>, <&clock HI3620_UARTCLK3>;
+			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
 
-		uart4: uart@b04000 {
+		uart4: serial@b04000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0xb04000 0x1000>;
 			interrupts = <0 24 4>;
-			clocks = <&clock HI3620_UARTCLK4>;
-			clock-names = "apb_pclk";
+			clocks = <&clock HI3620_UARTCLK4>, <&clock HI3620_UARTCLK4>;
+			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -535,10 +545,9 @@
 			compatible = "pinctrl-single";
 			reg = <0x803000 0x188>;
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			#pinctrl-cells = <1>;
 			#gpio-range-cells = <3>;
-			ranges;
 
 			pinctrl-single,register-width = <32>;
 			pinctrl-single,function-mask = <7>;
@@ -557,9 +566,8 @@
 			compatible = "pinconf-single";
 			reg = <0x803800 0x2dc>;
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			#pinctrl-cells = <1>;
-			ranges;
 
 			pinctrl-single,register-width = <32>;
 		};
diff --git a/arch/arm/boot/dts/hip01-ca9x2.dts b/arch/arm/boot/dts/hisilicon/hip01-ca9x2.dts
index f05e74eacfe0..f3faf247cd61 100644
--- a/arch/arm/boot/dts/hip01-ca9x2.dts
+++ b/arch/arm/boot/dts/hisilicon/hip01-ca9x2.dts
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Hisilicon Ltd. HiP01 SoC
+ * HiSilicon Ltd. HiP01 SoC
  *
- * Copyright (C) 2014 Hisilicon Ltd.
+ * Copyright (C) 2014 HiSilicon Ltd.
  * Copyright (C) 2014 Huawei Ltd.
  *
  * Author: Wang Long <long.wanglong@huawei.com>
@@ -37,7 +37,7 @@
 		};
 	};
 
-	memory {
+	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x80000000>;
 	};
diff --git a/arch/arm/boot/dts/hip01.dtsi b/arch/arm/boot/dts/hisilicon/hip01.dtsi
index 975d39828405..e17f36bd9006 100644
--- a/arch/arm/boot/dts/hip01.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hip01.dtsi
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Hisilicon Ltd. HiP01 SoC
+ * HiSilicon Ltd. HiP01 SoC
  *
- * Copyright (c) 2014 Hisilicon Ltd.
+ * Copyright (c) 2014 HiSilicon Ltd.
  * Copyright (c) 2014 Huawei Ltd.
  *
  * Author: Wang Long <long.wanglong@huawei.com>
@@ -35,47 +35,47 @@
 		interrupt-parent = <&gic>;
 		ranges = <0 0x10000000 0x20000000>;
 
-		amba {
+		amba-bus {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "simple-bus";
 			ranges;
 
-			uart0: uart@10001000 {
+			uart0: serial@10001000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x10001000 0x1000>;
-				clocks = <&hisi_refclk144mhz>;
-				clock-names = "apb_pclk";
+				clocks = <&hisi_refclk144mhz>, <&hisi_refclk144mhz>;
+				clock-names = "baudclk", "apb_pclk";
 				reg-shift = <2>;
 				interrupts = <0 32 4>;
 				status = "disabled";
 			};
 
-			uart1: uart@10002000 {
+			uart1: serial@10002000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x10002000 0x1000>;
-				clocks = <&hisi_refclk144mhz>;
-				clock-names = "apb_pclk";
+				clocks = <&hisi_refclk144mhz>, <&hisi_refclk144mhz>;
+				clock-names = "baudclk", "apb_pclk";
 				reg-shift = <2>;
 				interrupts = <0 33 4>;
 				status = "disabled";
 			};
 
-			uart2: uart@10003000 {
+			uart2: serial@10003000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x10003000 0x1000>;
-				clocks = <&hisi_refclk144mhz>;
-				clock-names = "apb_pclk";
+				clocks = <&hisi_refclk144mhz>, <&hisi_refclk144mhz>;
+				clock-names = "baudclk", "apb_pclk";
 				reg-shift = <2>;
 				interrupts = <0 34 4>;
 				status = "disabled";
 			};
 
-			uart3: uart@10006000 {
+			uart3: serial@10006000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x10006000 0x1000>;
-				clocks = <&hisi_refclk144mhz>;
-				clock-names = "apb_pclk";
+				clocks = <&hisi_refclk144mhz>, <&hisi_refclk144mhz>;
+				clock-names = "baudclk", "apb_pclk";
 				reg-shift = <2>;
 				interrupts = <0 4 4>;
 				status = "disabled";
diff --git a/arch/arm/boot/dts/hip04-d01.dts b/arch/arm/boot/dts/hisilicon/hip04-d01.dts
index 9019e0d2ef60..0210064bf6a5 100644
--- a/arch/arm/boot/dts/hip04-d01.dts
+++ b/arch/arm/boot/dts/hisilicon/hip04-d01.dts
@@ -22,8 +22,8 @@
 	};
 
 	soc {
-		uart0: uart@4007000 {
-			status = "ok";
+		uart0: serial@4007000 {
+			status = "okay";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/hip04.dtsi b/arch/arm/boot/dts/hisilicon/hip04.dtsi
index 4263a9339c2e..2424cc545c9c 100644
--- a/arch/arm/boot/dts/hip04.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hip04.dtsi
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Hisilicon Ltd. HiP04 SoC
+ * HiSilicon Ltd. HiP04 SoC
  *
- * Copyright (C) 2013-2014 Hisilicon Ltd.
+ * Copyright (C) 2013-2014 HiSilicon Ltd.
  * Copyright (C) 2013-2014 Linaro Ltd.
  *
  * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
@@ -213,7 +213,7 @@
 		};
 
 		sysctrl: sysctrl {
-			compatible = "hisilicon,sysctrl";
+			compatible = "hisilicon,sysctrl", "syscon";
 			reg = <0x3e00000 0x00100000>;
 		};
 
@@ -226,8 +226,8 @@
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x3000000 0x1000>;
 			interrupts = <0 224 4>;
-			clocks = <&clk_50m>, <&clk_50m>;
-			clock-names = "apb_pclk";
+			clocks = <&clk_50m>, <&clk_50m>, <&clk_50m>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
 		};
 
 		arm-pmu {
@@ -250,12 +250,12 @@
 				     <0 79 4>;
 		};
 
-		uart0: uart@4007000 {
+		uart0: serial@4007000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x4007000 0x1000>;
 			interrupts = <0 381 4>;
-			clocks = <&clk_168m>;
-			clock-names = "uartclk";
+			clocks = <&clk_168m>, <&clk_168m>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/hisi-x5hd2-dkb.dts b/arch/arm/boot/dts/hisilicon/hisi-x5hd2-dkb.dts
index d55e9cd3b12b..7758c19038f0 100644
--- a/arch/arm/boot/dts/hisi-x5hd2-dkb.dts
+++ b/arch/arm/boot/dts/hisilicon/hisi-x5hd2-dkb.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2013-2014 Linaro Ltd.
- * Copyright (c) 2013-2014 Hisilicon Limited.
+ * Copyright (c) 2013-2014 HiSilicon Limited.
  */
 
 /dts-v1/;
@@ -35,7 +35,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x80000000>;
 	};
diff --git a/arch/arm/boot/dts/hisi-x5hd2.dtsi b/arch/arm/boot/dts/hisilicon/hisi-x5hd2.dtsi
index 696e6982a688..dc991ba2a9fb 100644
--- a/arch/arm/boot/dts/hisi-x5hd2.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hisi-x5hd2.dtsi
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2013-2014 Linaro Ltd.
- * Copyright (c) 2013-2014 Hisilicon Limited.
+ * Copyright (c) 2013-2014 HiSilicon Limited.
  */
 
 #include <dt-bindings/clock/hix5hd2-clock.h>
@@ -30,7 +30,7 @@
 		interrupt-parent = <&gic>;
 		ranges = <0 0xf8000000 0x8000000>;
 
-		amba {
+		amba-bus {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "simple-bus";
@@ -86,48 +86,48 @@
 				status = "disabled";
 			};
 
-			uart0: uart@b00000 {
+			uart0: serial@b00000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x00b00000 0x1000>;
 				interrupts = <0 49 4>;
-				clocks = <&clock HIX5HD2_FIXED_83M>;
-				clock-names = "apb_pclk";
+				clocks = <&clock HIX5HD2_FIXED_83M>, <&clock HIX5HD2_FIXED_83M>;
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
-			uart1: uart@6000 {
+			uart1: serial@6000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x00006000 0x1000>;
 				interrupts = <0 50 4>;
-				clocks = <&clock HIX5HD2_FIXED_83M>;
-				clock-names = "apb_pclk";
+				clocks = <&clock HIX5HD2_FIXED_83M>, <&clock HIX5HD2_FIXED_83M>;
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
-			uart2: uart@b02000 {
+			uart2: serial@b02000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x00b02000 0x1000>;
 				interrupts = <0 51 4>;
-				clocks = <&clock HIX5HD2_FIXED_83M>;
-				clock-names = "apb_pclk";
+				clocks = <&clock HIX5HD2_FIXED_83M>, <&clock HIX5HD2_FIXED_83M>;
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
-			uart3: uart@b03000 {
+			uart3: serial@b03000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x00b03000 0x1000>;
 				interrupts = <0 52 4>;
-				clocks = <&clock HIX5HD2_FIXED_83M>;
-				clock-names = "apb_pclk";
+				clocks = <&clock HIX5HD2_FIXED_83M>, <&clock HIX5HD2_FIXED_83M>;
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
-			uart4: uart@b04000 {
+			uart4: serial@b04000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0xb04000 0x1000>;
 				interrupts = <0 53 4>;
-				clocks = <&clock HIX5HD2_FIXED_83M>;
-				clock-names = "apb_pclk";
+				clocks = <&clock HIX5HD2_FIXED_83M>, <&clock HIX5HD2_FIXED_83M>;
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
@@ -370,8 +370,9 @@
 				arm,primecell-periphid = <0x00141805>;
 				reg = <0xa2c000 0x1000>;
 				interrupts = <0 29 4>;
-				clocks = <&clock HIX5HD2_WDG0_RST>;
-				clock-names = "apb_pclk";
+				clocks = <&clock HIX5HD2_WDG0_RST>,
+					 <&clock HIX5HD2_WDG0_RST>;
+				clock-names = "wdog_clk", "apb_pclk";
 			};
 		};
 
@@ -381,7 +382,7 @@
 			interrupts = <1 13 0xf01>;
 		};
 
-		l2: l2-cache {
+		l2: cache-controller {
 			compatible = "arm,pl310-cache";
 			reg = <0x00a10000 0x100000>;
 			interrupts = <0 15 4>;
@@ -422,7 +423,7 @@
 			interrupts = <0 35 4>;
 			clocks = <&clock HIX5HD2_MMC_CIU_RST>,
 				 <&clock HIX5HD2_MMC_BIU_CLK>;
-			clock-names = "ciu", "biu";
+			clock-names = "biu", "ciu";
 		};
 
 		sd: mmc@1820000 {
@@ -431,7 +432,7 @@
 			interrupts = <0 34 4>;
 			clocks = <&clock HIX5HD2_SD_CIU_RST>,
 				 <&clock HIX5HD2_SD_BIU_CLK>;
-			clock-names = "ciu","biu";
+			clock-names = "biu", "ciu";
 		};
 
 		gmac0: ethernet@1840000 {
@@ -452,14 +453,14 @@
 			status = "disabled";
 		};
 
-		usb0: ehci@1890000 {
+		usb0: usb@1890000 {
 			compatible = "generic-ehci";
 			reg = <0x1890000 0x1000>;
 			interrupts = <0 66 4>;
 			clocks = <&clock HIX5HD2_USB_CLK>;
 		};
 
-		usb1: ohci@1880000 {
+		usb1: usb@1880000 {
 			compatible = "generic-ohci";
 			reg = <0x1880000 0x1000>;
 			interrupts = <0 67 4>;
@@ -467,7 +468,7 @@
 		};
 
 		peripheral_ctrl: syscon@a20000 {
-			compatible = "syscon";
+			compatible = "hisilicon,peri-subctrl", "syscon";
 			reg = <0xa20000 0x1000>;
 		};
 
diff --git a/arch/arm/boot/dts/hisilicon/sd5203.dts b/arch/arm/boot/dts/hisilicon/sd5203.dts
new file mode 100644
index 000000000000..69381819e07b
--- /dev/null
+++ b/arch/arm/boot/dts/hisilicon/sd5203.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020 HiSilicon Limited.
+ *
+ * DTS file for Hisilicon SD5203 Board
+ */
+
+/dts-v1/;
+
+/ {
+	model = "Hisilicon SD5203";
+	compatible = "H836ASDJ", "hisilicon,sd5203";
+	interrupt-parent = <&vic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen {
+		bootargs = "console=ttyS0,9600 earlycon=uart8250,mmio32,0x1600d000";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0 {
+			device_type = "cpu";
+			compatible = "arm,arm926ej-s";
+			reg = <0x0>;
+		};
+	};
+
+	memory@30000000 {
+		device_type = "memory";
+		reg = <0x30000000 0x8000000>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges;
+
+		vic: interrupt-controller@10130000 {
+			compatible = "snps,dw-apb-ictl";
+			reg = <0x10130000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		refclk125mhz: refclk125mhz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <125000000>;
+		};
+
+		timer0: timer@16002000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x16002000 0x1000>;
+			interrupts = <4>;
+			clocks = <&refclk125mhz>;
+			clock-names = "apb_pclk";
+		};
+
+		timer1: timer@16003000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x16003000 0x1000>;
+			interrupts = <5>;
+			clocks = <&refclk125mhz>;
+			clock-names = "apb_pclk";
+		};
+
+		uart0: serial@1600d000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x1600d000 0x1000>;
+			bus_id = "uart0";
+			clocks = <&refclk125mhz>;
+			clock-names = "baudclk", "apb_pclk";
+			reg-shift = <2>;
+			interrupts = <17>;
+		};
+
+		uart1: serial@1600c000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x1600c000 0x1000>;
+			clocks = <&refclk125mhz>;
+			clock-names = "baudclk", "apb_pclk";
+			reg-shift = <2>;
+			interrupts = <16>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/hpe/Makefile b/arch/arm/boot/dts/hpe/Makefile
new file mode 100644
index 000000000000..e175b1732cdb
--- /dev/null
+++ b/arch/arm/boot/dts/hpe/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_HPE_GXP) += \
+	hpe-bmc-dl360gen10.dtb
diff --git a/arch/arm/boot/dts/hpe/hpe-bmc-dl360gen10.dts b/arch/arm/boot/dts/hpe/hpe-bmc-dl360gen10.dts
new file mode 100644
index 000000000000..3a7382ce40ef
--- /dev/null
+++ b/arch/arm/boot/dts/hpe/hpe-bmc-dl360gen10.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for HPE DL360Gen10
+ */
+
+/include/ "hpe-gxp.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "hpe,gxp-dl360gen10", "hpe,gxp";
+	model = "Hewlett Packard Enterprise ProLiant dl360 Gen10";
+
+	aliases {
+		serial0 = &uartc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/hpe/hpe-gxp.dtsi b/arch/arm/boot/dts/hpe/hpe-gxp.dtsi
new file mode 100644
index 000000000000..cf735b3c4f35
--- /dev/null
+++ b/arch/arm/boot/dts/hpe/hpe-gxp.dtsi
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for HPE GXP
+ */
+
+/dts-v1/;
+/ {
+	model = "Hewlett Packard Enterprise GXP BMC";
+	compatible = "hpe,gxp";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+		};
+	};
+
+	clocks {
+		pll: clock-0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1600000000>;
+		};
+
+		iopclk: clock-1 {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <4>;
+			clock-mult = <1>;
+			clocks = <&pll>;
+		};
+	};
+
+	axi {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		dma-ranges;
+
+		L2: cache-controller@b0040000 {
+			compatible = "arm,pl310-cache";
+			reg = <0xb0040000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		ahb@c0000000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xc0000000 0x30000000>;
+			dma-ranges;
+
+			vic0: interrupt-controller@eff0000 {
+				compatible = "arm,pl192-vic";
+				reg = <0xeff0000 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			vic1: interrupt-controller@80f00000 {
+				compatible = "arm,pl192-vic";
+				reg = <0x80f00000 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			uarta: serial@e0 {
+				compatible = "ns16550a";
+				reg = <0xe0 0x8>;
+				interrupts = <17>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			uartb: serial@e8 {
+				compatible = "ns16550a";
+				reg = <0xe8 0x8>;
+				interrupts = <18>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			uartc: serial@f0 {
+				compatible = "ns16550a";
+				reg = <0xf0 0x8>;
+				interrupts = <19>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			usb0: usb@efe0000 {
+				compatible = "hpe,gxp-ehci", "generic-ehci";
+				reg = <0xefe0000 0x100>;
+				interrupts = <7>;
+				interrupt-parent = <&vic0>;
+			};
+
+			st: timer@80 {
+				compatible = "hpe,gxp-timer";
+				reg = <0x80 0x16>;
+				interrupts = <0>;
+				interrupt-parent = <&vic0>;
+				clocks = <&iopclk>;
+				clock-names = "iop";
+			};
+
+			usb1: usb@efe0100 {
+				compatible = "hpe,gxp-ohci", "generic-ohci";
+				reg = <0xefe0100 0x110>;
+				interrupts = <6>;
+				interrupt-parent = <&vic0>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx25-karo-tx25.dts b/arch/arm/boot/dts/imx25-karo-tx25.dts
deleted file mode 100644
index 0950eb66d3d9..000000000000
--- a/arch/arm/boot/dts/imx25-karo-tx25.dts
+++ /dev/null
@@ -1,108 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Sascha Hauer, Pengutronix
- */
-
-/dts-v1/;
-#include "imx25.dtsi"
-
-/ {
-	model = "Ka-Ro TX25";
-	compatible = "karo,imx25-tx25", "fsl,imx25";
-
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_fec_phy: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "fec-phy";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio4 9 0>;
-			enable-active-high;
-		};
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x02000000 0x90000000 0x02000000>;
-	};
-};
-
-&iomuxc {
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX25_PAD_UART1_TXD__UART1_TXD 0x80000000
-			MX25_PAD_UART1_RXD__UART1_RXD 0x80000000
-			MX25_PAD_UART1_CTS__UART1_CTS 0x80000000
-			MX25_PAD_UART1_RTS__UART1_RTS 0x80000000
-		>;
-	};
-
-	pinctrl_fec: fecgrp {
-		fsl,pins = <
-			MX25_PAD_D11__GPIO_4_9		0x80000000 /* FEC PHY power on pin */
-			MX25_PAD_D13__GPIO_4_7		0x80000000 /* FEC reset */
-			MX25_PAD_FEC_MDC__FEC_MDC	0x80000000
-			MX25_PAD_FEC_MDIO__FEC_MDIO	0x80000000
-			MX25_PAD_FEC_TDATA0__FEC_TDATA0	0x80000000
-			MX25_PAD_FEC_TDATA1__FEC_TDATA1	0x80000000
-			MX25_PAD_FEC_TX_EN__FEC_TX_EN	0x80000000
-			MX25_PAD_FEC_RDATA0__FEC_RDATA0	0x80000000
-			MX25_PAD_FEC_RDATA1__FEC_RDATA1	0x80000000
-			MX25_PAD_FEC_RX_DV__FEC_RX_DV	0x80000000
-			MX25_PAD_FEC_TX_CLK__FEC_TX_CLK	0x80000000
-		>;
-	};
-
-	pinctrl_nfc: nfcgrp {
-		fsl,pins = <
-			MX25_PAD_NF_CE0__NF_CE0		0x80000000
-			MX25_PAD_NFWE_B__NFWE_B		0x80000000
-			MX25_PAD_NFRE_B__NFRE_B		0x80000000
-			MX25_PAD_NFALE__NFALE		0x80000000
-			MX25_PAD_NFCLE__NFCLE		0x80000000
-			MX25_PAD_NFWP_B__NFWP_B		0x80000000
-			MX25_PAD_NFRB__NFRB		0x80000000
-			MX25_PAD_D7__D7			0x80000000
-			MX25_PAD_D6__D6			0x80000000
-			MX25_PAD_D5__D5			0x80000000
-			MX25_PAD_D4__D4			0x80000000
-			MX25_PAD_D3__D3			0x80000000
-			MX25_PAD_D2__D2			0x80000000
-			MX25_PAD_D1__D1			0x80000000
-			MX25_PAD_D0__D0			0x80000000
-		>;
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-reset-gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
-	phy-mode = "rmii";
-	phy-supply = <&reg_fec_phy>;
-	status = "okay";
-};
-
-&nfc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nfc>;
-	nand-on-flash-bbt;
-	nand-ecc-mode = "hw";
-	nand-bus-width = <8>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
deleted file mode 100644
index 3ed2b328f7ef..000000000000
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ /dev/null
@@ -1,80 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Armadeus Systems - <support@armadeus.com>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "Armadeus Systems APF28 module";
-	compatible = "armadeus,imx28-apf28", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			gpmi-nand@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-
-				partition@0 {
-					label = "u-boot";
-					reg = <0x0 0x300000>;
-				};
-
-				partition@300000 {
-					label = "env";
-					reg = <0x300000 0x80000>;
-				};
-
-				partition@380000 {
-					label = "env2";
-					reg = <0x380000 0x80000>;
-				};
-
-				partition@400000 {
-					label = "dtb";
-					reg = <0x400000 0x80000>;
-				};
-
-				partition@480000 {
-					label = "splash";
-					reg = <0x480000 0x80000>;
-				};
-
-				partition@500000 {
-					label = "kernel";
-					reg = <0x500000 0x800000>;
-				};
-
-				partition@d00000 {
-					label = "rootfs";
-					reg = <0xd00000 0xf300000>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			status = "okay";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
deleted file mode 100644
index 1b253b47006c..000000000000
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ /dev/null
@@ -1,225 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Armadeus Systems - <support@armadeus.com>
- */
-
-/* APF28Dev is a docking board for the APF28 SOM */
-#include "imx28-apf28.dts"
-
-/ {
-	model = "Armadeus Systems APF28Dev docking/development board";
-	compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_apf28dev>;
-
-				hog_pins_apf28dev: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D16__GPIO_1_16
-						MX28_PAD_LCD_D17__GPIO_1_17
-						MX28_PAD_LCD_D18__GPIO_1_18
-						MX28_PAD_LCD_D19__GPIO_1_19
-						MX28_PAD_LCD_D20__GPIO_1_20
-						MX28_PAD_LCD_D21__GPIO_1_21
-						MX28_PAD_LCD_D22__GPIO_1_22
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apf28dev: lcdif-apf28dev@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				usb0_otg_apf28dev: otg-apf28dev@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D23__GPIO_1_23
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_16bit_pins_a
-						&lcdif_pins_apf28dev>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <16>;
-					bus-width = <16>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33000033>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <96>;
-							hfront-porch = <96>;
-							vback-porch = <20>;
-							vfront-porch = <21>;
-							hsync-len = <64>;
-							vsync-len = <4>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				xceiver-supply = <&reg_can0_vcc>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				uart-has-rtscts;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_otg_apf28dev
-					&usb0_id_pins_b>;
-			vbus-supply = <&reg_usb0_vbus>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb0_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 23 1>;
-			enable-active-high;
-		};
-
-		reg_can0_vcc: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "can0_vcc";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio0 21 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-
-		pwms = <&pwm 3 191000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		user-button {
-			label = "User button";
-			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
-			linux,code = <0x100>;
-			wakeup-source;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
deleted file mode 100644
index 3a184d13887b..000000000000
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ /dev/null
@@ -1,230 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "Bluegiga APX4 Development Kit";
-	compatible = "bluegiga,apx4devkit", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x04000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			gpmi-nand@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_RDY1__GPIO_0_21
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_JTAG_RTCK__GPIO_4_20
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apx4: lcdif-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA4__SSP2_D0
-						MX28_PAD_SSP0_DATA5__SSP2_D3
-						MX28_PAD_SSP0_DATA6__SSP2_CMD
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-						MX28_PAD_SSP2_SS1__SSP2_D1
-						MX28_PAD_SSP2_SS2__SSP2_D2
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-					>;
-					fsl,drive-strength = <MXS_DRIVE_12mA>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_apx4>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <88>;
-							hfront-porch = <40>;
-							vback-porch = <32>;
-							vfront-porch = <13>;
-							hsync-len = <48>;
-							vsync-len = <3>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				pcf8563: rtc@51 {
-					compatible = "phg,pcf8563";
-					reg = <0x51>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_2pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-
-	sound {
-		compatible = "bluegiga,apx4devkit-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "apx4devkit-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio3 28 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
deleted file mode 100644
index 85aa1cc3ff66..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ /dev/null
@@ -1,140 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Free Electrons
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Crystalfontz CFA-10036 Board";
-	compatible = "crystalfontz,cfa10036", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				ssd1306_cfa10036: ssd1306-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__GPIO_2_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins_cfa10036: leds-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_RX__GPIO_3_4
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				usb0_otg_cfa10036: otg-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_RDY0__USB0_ID
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x31c3 /*
-						MX28_PAD_PWM3__GPIO_3_28 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
-				};
-
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				bus-width = <4>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_b>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_b>;
-				clock-frequency = <400000>;
-				status = "okay";
-
-				ssd1306: oled@3c {
-					compatible = "solomon,ssd1306fb-i2c";
-					pinctrl-names = "default";
-					pinctrl-0 = <&ssd1306_cfa10036>;
-					reg = <0x3c>;
-					reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-					solomon,height = <32>;
-					solomon,width = <128>;
-					solomon,page-offset = <0>;
-					solomon,com-lrremap;
-					solomon,com-invdir;
-					solomon,com-offset = <32>;
-				};
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_otg_cfa10036>;
-			dr_mode = "peripheral";
-			phy_type = "utmi";
-			status = "okay";
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_cfa10036>;
-
-		power {
-			gpios = <&gpio3 4 1>;
-			default-state = "on";
-		};
-	};
-
-	reg_vddio_sd0: vddio-sd0 {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&mmc_pwr_cfa10036>;
-		regulator-name = "vddio-sd0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 28 0>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
deleted file mode 100644
index a92b05ef390f..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ /dev/null
@@ -1,428 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Free Electrons
- */
-
-/*
- * The CFA-10049 is an expansion board for the CFA-10036 module, thus we
- * need to include the CFA-10036 DTS.
- */
-#include "imx28-cfa10036.dts"
-
-/ {
-	model = "Crystalfontz CFA-10049 Board";
-	compatible = "crystalfontz,cfa10049", "crystalfontz,cfa10036", "fsl,imx28";
-
-	i2cmux {
-		compatible = "i2c-mux-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2cmux_pins_cfa10049>;
-		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
-		i2c-parent = <&i2c1>;
-
-		i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			adc0: nau7802@2a {
-				compatible = "nuvoton,nau7802";
-				reg = <0x2a>;
-				nuvoton,vldo = <3000>;
-			};
-		};
-
-		i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			adc1: nau7802@2a {
-				compatible = "nuvoton,nau7802";
-				reg = <0x2a>;
-				nuvoton,vldo = <3000>;
-			};
-		};
-
-		i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-
-				adc2: nau7802@2a {
-				compatible = "nuvoton,nau7802";
-				reg = <0x2a>;
-				nuvoton,vldo = <3000>;
-			};
-		};
-
-		i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			pca9555: pca9555@20 {
-				compatible = "nxp,pca9555";
-				pinctrl-names = "default";
-				pinctrl-0 = <&pca_pins_cfa10049>;
-				interrupt-parent = <&gpio2>;
-				interrupts = <19 0x2>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x20>;
-			};
-		};
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10049: usb-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				i2cmux_pins_cfa10049: i2cmux-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D22__GPIO_1_22
-						MX28_PAD_LCD_D23__GPIO_1_23
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_pins_cfa10049: mac0-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS2__GPIO_2_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				pca_pins_cfa10049: pca-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS0__GPIO_2_19
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				rotary_pins_cfa10049: rotary-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF1_SDATA0__GPIO_3_26
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				spi2_pins_cfa10049: spi2-cfa10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				spi3_pins_cfa10049: spi3-cfa10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_RDN__GPIO_0_24
-						MX28_PAD_GPMI_RESETN__GPIO_0_28
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_ALE__GPIO_0_26
-						MX28_PAD_GPMI_CLE__GPIO_0_27
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10049: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				w1_gpio_pins: w1-gpio@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D21__GPIO_1_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
-					     &lcdif_pins_cfa10049
-					     &lcdif_pins_cfa10049_pullup>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9216000>;
-							hactive = <320>;
-							vactive = <480>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <15>;
-							vsync-len = <15>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-
-			i2c1: i2c@8005a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c1_pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10049>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a
-				&mac0_pins_cfa10049>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
-	spi2 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi2_pins_cfa10049>;
-		status = "okay";
-		gpio-sck = <&gpio2 16 0>;
-		gpio-mosi = <&gpio2 17 0>;
-		gpio-miso = <&gpio2 18 0>;
-		cs-gpios = <&gpio3 5 0>;
-		num-chipselects = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hx8357: hx8357@0 {
-			compatible = "himax,hx8357b", "himax,hx8357";
-			reg = <0>;
-			spi-max-frequency = <100000>;
-			spi-cpol;
-			spi-cpha;
-			gpios-reset = <&gpio3 30 0>;
-			im-gpios = <&gpio5 4 0 &gpio5 5 0 &gpio5 6 0>;
-		};
-	};
-
-	spi3 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi3_pins_cfa10049>;
-		status = "okay";
-		gpio-sck = <&gpio0 24 0>;
-		gpio-mosi = <&gpio0 28 0>;
-		cs-gpios = <&gpio0 17 0 &gpio0 26 0 &gpio0 27 0>;
-		num-chipselects = <3>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio5: gpio5@0 {
-			compatible = "fairchild,74hc595";
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <0>;
-			registers-number = <2>;
-			spi-max-frequency = <100000>;
-		};
-
-		gpio6: gpio6@1 {
-			compatible = "fairchild,74hc595";
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <1>;
-			registers-number = <4>;
-			spi-max-frequency = <100000>;
-		};
-
-		dac0: dh2228@2 {
-			compatible = "rohm,dh2228fv";
-			reg = <2>;
-			spi-max-frequency = <100000>;
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
-
-		rotary_button {
-			label = "rotary_button";
-			gpios = <&gpio3 26 1>;
-			debounce-interval = <10>;
-			linux,code = <28>;
-		};
-	};
-
-	rotary {
-		compatible = "rotary-encoder";
-		pinctrl-names = "default";
-		pinctrl-0 = <&rotary_pins_cfa10049>;
-		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
-		linux,axis = <1>; /* REL_Y */
-		rotary-encoder,relative-axis;
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-
-	};
-
-	onewire {
-		compatible = "w1-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&w1_gpio_pins>;
-		status = "okay";
-		gpios = <&gpio1 21 0>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
deleted file mode 100644
index d05c370dfc17..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ /dev/null
@@ -1,161 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Crystalfontz America, Inc.
- * 				  Free Electrons
- */
-
-/*
- * The CFA-10055 is an expansion board for the CFA-10036 module and
- * CFA-10037, thus we need to include the CFA-10037 DTS.
- */
-#include "imx28-cfa10037.dts"
-
-/ {
-	model = "Crystalfontz CFA-10055 Board";
-	compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				spi2_pins_cfa10055: spi2-cfa10055@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10055: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10055
-					     &lcdif_pins_cfa10055
-					     &lcdif_pins_cfa10055_pullup>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9216000>;
-							hactive = <320>;
-							vactive = <480>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <15>;
-							vsync-len = <15>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-		};
-	};
-
-	spi2 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi2_pins_cfa10055>;
-		status = "okay";
-		gpio-sck = <&gpio2 16 0>;
-		gpio-mosi = <&gpio2 17 0>;
-		gpio-miso = <&gpio2 18 0>;
-		cs-gpios = <&gpio3 5 0>;
-		num-chipselects = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hx8357: hx8357@0 {
-			compatible = "himax,hx8357b", "himax,hx8357";
-			reg = <0>;
-			spi-max-frequency = <100000>;
-			spi-cpol;
-			spi-cpha;
-			gpios-reset = <&gpio3 30 0>;
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
deleted file mode 100644
index c1060bd5f17f..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Free Electrons
- */
-
-/*
- * The CFA-10055 is an expansion board for the CFA-10036 module and
- * CFA-10037, thus we need to include the CFA-10037 DTS.
- */
-#include "imx28-cfa10037.dts"
-
-/ {
-	model = "Crystalfontz CFA-10056 Board";
-	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				spi2_pins_cfa10056: spi2-cfa10056@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_pins_cfa10056: lcdif-10056@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-						&lcdif_pins_cfa10056
-						&lcdif_pins_cfa10056_pullup >;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <32000000>;
-							hactive = <480>;
-							vactive = <800>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <5>;
-							vsync-len = <5>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-	};
-
-	spi2 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi2_pins_cfa10056>;
-		status = "okay";
-		gpio-sck = <&gpio2 16 0>;
-		gpio-mosi = <&gpio2 17 0>;
-		gpio-miso = <&gpio2 18 0>;
-		cs-gpios = <&gpio3 5 0>;
-		num-chipselects = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hx8369: hx8369@0 {
-			compatible = "himax,hx8369a", "himax,hx8369";
-			reg = <0>;
-			spi-max-frequency = <100000>;
-			spi-cpol;
-			spi-cpha;
-			gpios-reset = <&gpio3 30 0>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
deleted file mode 100644
index 2f7e479dbc74..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ /dev/null
@@ -1,171 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Crystalfontz America, Inc.
- * Copyright 2012 Free Electrons
- */
-
-/*
- * The CFA-10057 is an expansion board for the CFA-10036 module, thus we
- * need to include the CFA-10036 DTS.
- */
-#include "imx28-cfa10036.dts"
-
-/ {
-	model = "Crystalfontz CFA-10057 Board";
-	compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10057: usb-10057@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10057: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10057
-					     &lcdif_pins_cfa10057>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <480>;
-							vactive = <800>;
-							hfront-porch = <12>;
-							hback-porch = <2>;
-							vfront-porch = <5>;
-							vback-porch = <3>;
-							hsync-len = <2>;
-							vsync-len = <2>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-
-			i2c1: i2c@8005a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c1_pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10057>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 4 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
deleted file mode 100644
index 4465fd86785a..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ /dev/null
@@ -1,138 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Crystalfontz America, Inc.
- * Copyright 2013 Free Electrons
- */
-
-/*
- * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
- * need to include the CFA-10036 DTS.
- */
-#include "imx28-cfa10036.dts"
-
-/ {
-	model = "Crystalfontz CFA-10058 Board";
-	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10058: usb-10058@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10058: lcdif-10058@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-						 &lcdif_pins_cfa10058>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <40>;
-							hfront-porch = <40>;
-							vback-porch = <13>;
-							vfront-porch = <29>;
-							hsync-len = <8>;
-							vsync-len = <8>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10058>;
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
deleted file mode 100644
index d451fa018d83..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2-485.dts
+++ /dev/null
@@ -1,184 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2 485";
-	compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		rs485-red {
-			label = "duckbill:red:rs485";
-			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-		};
-
-		rs485-green {
-			label = "duckbill:green:rs485";
-			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
deleted file mode 100644
index bacb846f99e3..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
+++ /dev/null
@@ -1,213 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2 EnOcean";
-	compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_AUART0_CTS__GPIO_3_2
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				enocean_button: enocean-button@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		enocean-blue {
-			label = "duckbill:blue:enocean";
-			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-		};
-
-		enocean-red {
-			label = "duckbill:red:enocean";
-			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
-		};
-
-		enocean-green {
-			label = "duckbill:green:enocean";
-			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&enocean_button>;
-
-		enocean {
-			label = "EnOcean";
-			linux,code = <KEY_NEW>;
-			gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
deleted file mode 100644
index 0e8be5975709..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
+++ /dev/null
@@ -1,194 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2 SPI";
-	compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
-
-	aliases {
-		ethernet1 = &qca7000;
-	};
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				qca7000: ethernet@0 {
-					reg = <0>;
-					compatible = "qca,qca7000";
-					pinctrl-names = "default";
-					pinctrl-0 = <&qca7000_pins>;
-					interrupt-parent = <&gpio3>;
-					interrupts = <3 IRQ_TYPE_EDGE_RISING>;
-					spi-cpha;
-					spi-cpol;
-					spi-max-frequency = <8000000>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: led@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				qca7000_pins: qca7000@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
-						MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
-						MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
-						MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
-						MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
-						MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts
deleted file mode 100644
index 23fd3036404d..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2.dts
+++ /dev/null
@@ -1,178 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2";
-	compatible = "i2se,duckbill-2", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
deleted file mode 100644
index c666afb12445..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ /dev/null
@@ -1,147 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- */
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill";
-	compatible = "i2se,duckbill", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_RX__GPIO_3_4
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			status = "okay";
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
deleted file mode 100644
index 96c1d106bc64..000000000000
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ /dev/null
@@ -1,360 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2012 Freescale Semiconductor, Inc.
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "Freescale i.MX28 Evaluation Kit";
-	compatible = "fsl,imx28-evk", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	reg_vddio_sd0: regulator-vddio-sd0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vddio-sd0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 28 0>;
-	};
-
-	reg_fec_3v3: regulator-fec-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "fec-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 15 0>;
-	};
-
-	reg_usb0_vbus: regulator-usb0-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb0_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 9 0>;
-		enable-active-high;
-	};
-
-	reg_usb1_vbus: regulator-usb1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 8 0>;
-		enable-active-high;
-	};
-
-	reg_lcd_3v3: regulator-lcd-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 30 0>;
-		enable-active-high;
-	};
-
-	reg_can_3v3: regulator-can-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "can-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 13 0>;
-		enable-active-high;
-	};
-
-	reg_lcd_5v: regulator-lcd-5v {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd-5v";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	panel {
-		compatible = "sii,43wvf1g";
-		backlight = <&backlight_display>;
-		dvdd-supply = <&reg_lcd_3v3>;
-		avdd-supply = <&reg_lcd_5v>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&display_out>;
-			};
-		};
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			gpmi-nand@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
-					     &gpmi_pins_evk>;
-				status = "okay";
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				wp-gpios = <&gpio2 12 0>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp1: spi@80012000 {
-				compatible = "fsl,imx28-mmc";
-				bus-width = <8>;
-				wp-gpios = <&gpio0 28 0>;
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: m25p80@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "sst,sst25vf016b", "jedec,spi-nor";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP1_CMD__GPIO_2_13
-						MX28_PAD_SSP1_DATA3__GPIO_2_15
-						MX28_PAD_ENET0_RX_CLK__GPIO_4_13
-						MX28_PAD_SSP1_SCK__GPIO_2_12
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_AUART2_RX__GPIO_3_8
-						MX28_PAD_AUART2_TX__GPIO_3_9
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pin_gpio3_5: led_gpio3_5@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				gpmi_pins_evk: gpmi-nand-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPMI_CE1N
-						MX28_PAD_GPMI_RDY1__GPMI_READY1
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_evk: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_evk>;
-				status = "okay";
-
-				port {
-					display_out: endpoint {
-						remote-endpoint = <&panel_in>;
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				xceiver-supply = <&reg_can_3v3>;
-				status = "okay";
-			};
-
-			can1: can@80034000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can1_pins_a>;
-				xceiver-supply = <&reg_can_3v3>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-				fsl,ave-ctrl = <4>;
-				fsl,ave-delay = <2>;
-				fsl,settling = <10>;
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				at24@51 {
-					compatible = "atmel,24c32";
-					pagesize = <32>;
-					reg = <0x51>;
-				};
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				uart-has-rtscts;
-				status = "okay";
-			};
-
-			auart3: serial@80070000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_id_pins_a>;
-			vbus-supply = <&reg_usb0_vbus>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-supply = <&reg_fec_3v3>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx28-evk-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "imx28-evk-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_gpio3_5>;
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio3 5 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	backlight_display: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-m28.dtsi b/arch/arm/boot/dts/imx28-m28.dtsi
deleted file mode 100644
index 0bac72d5351f..000000000000
--- a/arch/arm/boot/dts/imx28-m28.dtsi
+++ /dev/null
@@ -1,56 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2014 Marek Vasut <marex@denx.de>
- */
-
-#include "imx28.dtsi"
-
-/ {
-	model = "Aries/DENX M28";
-	compatible = "aries,m28", "denx,m28", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			gpmi-nand@8000c000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				rtc: rtc@68 {
-					compatible = "st,m41t62";
-					reg = <0x68>;
-				};
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
deleted file mode 100644
index 91bd6deffee5..000000000000
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ /dev/null
@@ -1,266 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2013 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "MSR M28CU3";
-	compatible = "msr,m28cu3", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			gpmi-nand@8000c000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-
-				partition@0 {
-					label = "gpmi-nfc-0-boot";
-					reg = <0x00000000 0x01400000>;
-					read-only;
-				};
-
-				partition@1 {
-					label = "gpmi-nfc-general-use";
-					reg = <0x01400000 0x0ec00000>;
-				};
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					     &mmc0_cd_cfg
-					     &mmc0_sck_cfg>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_a
-					     &mmc2_cd_cfg
-					     &mmc2_sck_cfg_a>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd1>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS0__GPIO_2_19
-						MX28_PAD_PWM4__GPIO_3_29
-						MX28_PAD_AUART2_RX__GPIO_3_8
-						MX28_PAD_ENET0_RX_CLK__GPIO_4_13
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_m28: lcdif-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_VSYNC__LCD_VSYNC
-						MX28_PAD_LCD_HSYNC__LCD_HSYNC
-						MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
-						MX28_PAD_LCD_RESET__LCD_RESET
-						MX28_PAD_LCD_CS__LCD_ENABLE
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins_gpio: leds-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP3_MISO__GPIO_2_26
-						MX28_PAD_SSP3_SCK__GPIO_2_24
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			ocotp@8002c000 {
-				status = "okay";
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_m28>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <6410256>;
-							hactive = <320>;
-							vactive = <240>;
-							hback-porch = <38>;
-							hfront-porch = <20>;
-							vback-porch = <15>;
-							vfront-porch = <5>;
-							hsync-len = <30>;
-							vsync-len = <3>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_b>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			auart3: serial@80070000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_2pins_b>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb1_pins_a>;
-			disable-over-current;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_gpio>;
-
-		user1 {
-			label = "sd0-led";
-			gpios = <&gpio2 26 0>;
-			linux,default-trigger = "mmc0";
-		};
-
-		user2 {
-			label = "sd1-led";
-			gpios = <&gpio2 24 0>;
-			linux,default-trigger = "mmc2";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_vddio_sd0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 29 0>;
-		};
-
-		reg_vddio_sd1: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vddio-sd1";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 19 0>;
-		};
-
-		reg_usb1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 8 0>;
-			enable-active-high;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
deleted file mode 100644
index f3bddc5ada4b..000000000000
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ /dev/null
@@ -1,271 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
-
- * Copyright (C) 2012 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx28-m28.dtsi"
-
-/ {
-	model = "Aries/DENX M28EVK";
-	compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					     &mmc0_cd_cfg
-					     &mmc0_sck_cfg>;
-				bus-width = <8>;
-				wp-gpios = <&gpio3 10 0>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: m25p80@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "m25p80", "jedec,spi-nor";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_AUART2_CTS__GPIO_3_10
-						MX28_PAD_AUART2_RTS__GPIO_3_11
-						MX28_PAD_AUART3_RX__GPIO_3_12
-						MX28_PAD_AUART3_TX__GPIO_3_13
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_m28: lcdif-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
-						MX28_PAD_LCD_ENABLE__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_m28>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <16>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33260000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <0>;
-							hfront-porch = <256>;
-							vback-porch = <0>;
-							vfront-porch = <45>;
-							hsync-len = <1>;
-							vsync-len = <1>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				status = "okay";
-			};
-
-			can1: can@80034000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can1_pins_a>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				eeprom: eeprom@51 {
-					compatible = "atmel,24c128";
-					reg = <0x51>;
-					pagesize = <32>;
-				};
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_b>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			vbus-supply = <&reg_usb0_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_pins_a>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb1_pins_a>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			clocks = <&clks 57>, <&clks 57>;
-			clock-names = "ipg", "ahb";
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 4 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	regulators {
-		reg_vddio_sd0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 28 0>;
-		};
-
-		reg_usb0_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 12 0>;
-		};
-
-		reg_usb1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 13 0>;
-		};
-	};
-
-	sound {
-		compatible = "denx,m28evk-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "m28evk-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
deleted file mode 100644
index 43be7a6a769b..000000000000
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ /dev/null
@@ -1,166 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2012 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "SchulerControl GmbH, SC SPS 1";
-	compatible = "schulercontrol,imx28-sps1", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog-gpios@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D00__GPIO_0_0
-						MX28_PAD_GPMI_D03__GPIO_0_3
-						MX28_PAD_GPMI_D06__GPIO_0_6
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: m25p80@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "everspin,mr25h256", "mr25h256";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				rtc: rtc@51 {
-					compatible = "nxp,pcf8563";
-					reg = <0x51>;
-				};
-
-				eeprom: eeprom@52 {
-					compatible = "atmel,24c64";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			vbus-supply = <&reg_usb0_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_pins_b>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb0_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 9 0>;
-		};
-	};
-
-	leds {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "gpio-leds";
-		status = "okay";
-
-		led@1 {
-			label = "sps1-1:yellow:user";
-			gpios = <&gpio0 6 0>;
-			linux,default-trigger = "heartbeat";
-			reg = <0>;
-		};
-
-		led@2 {
-			label = "sps1-2:red:user";
-			gpios = <&gpio0 3 0>;
-			linux,default-trigger = "heartbeat";
-			reg = <1>;
-		};
-
-		led@3 {
-			label = "sps1-3:red:user";
-			gpios = <&gpio0 0 0>;
-			default-trigger = "heartbeat";
-			reg = <2>;
-		};
-
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-ts4600.dts b/arch/arm/boot/dts/imx28-ts4600.dts
deleted file mode 100644
index 097ec35c62d8..000000000000
--- a/arch/arm/boot/dts/imx28-ts4600.dts
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2016 Savoir-Faire Linux
- * Author: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-#include "dt-bindings/gpio/gpio.h"
-
-/ {
-
-	model = "Technologic Systems i.MX28 TS-4600";
-	compatible = "technologic,imx28-ts4600", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x10000000>;   /* 256MB */
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					     &mmc0_sck_cfg
-					     &en_sd_pwr>;
-				broken-cd = <1>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-
-				en_sd_pwr: en-sd-pwr@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_PWM3__GPIO_3_28
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-			};
-		};
-
-		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	reg_vddio_sd0: regulator-vddio-sd0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vddio-sd0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		gpio = <&gpio3 28 GPIO_ACTIVE_LOW>;
-	};
-
-};
diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
deleted file mode 100644
index cd075621de52..000000000000
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ /dev/null
@@ -1,297 +0,0 @@
-/*
- * Copyright 2014-2016 Toradex AG
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6dl.dtsi"
-#include "imx6qdl-colibri.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6DL/S on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
-		     "fsl,imx6dl";
-
-	/* Will be filled by the bootloader */
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0>;
-	};
-
-	aliases {
-		i2c0 = &i2c2;
-		i2c1 = &i2c3;
-	};
-
-	aliases {
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	/* Fixed crystal dedicated to mcp251x */
-	clk16m: clock-16m {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <16000000>;
-		clock-output-names = "clk16m";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
-
-/* Colibri SSP */
-&ecspi4 {
-	status = "okay";
-
-	mcp251x0: mcp251x@0 {
-		compatible = "microchip,mcp2515";
-		reg = <0>;
-		clocks = <&clk16m>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <27 0x2>;
-		spi-max-frequency = <10000000>;
-		status = "okay";
-	};
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/*
- * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
- */
-&i2c3 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pcap_1>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-		&pinctrl_weim_gpio_1 &pinctrl_weim_gpio_2
-		&pinctrl_weim_gpio_3 &pinctrl_weim_gpio_4
-		&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
-		&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
-	>;
-
-	pinctrl_pcap_1: pcap1grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0 /* SODIMM 28 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10	0x1b0b0 /* SODIMM 30 */
-		>;
-	};
-
-	pinctrl_mxt_ts: mxttsgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x130b0 /* SODIMM 107 */
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14	0x130b0 /* SODIMM 106 */
-		>;
-	};
-};
-
-&ipu1_di0_disp0 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	status = "okay";
-};
-
-/* Colibri MMC */
-&usdhc1 {
-	status = "okay";
-};
-
-&weim {
-	status = "okay";
-
-	/* weim memory map: 32MB on CS0, CS1, CS2 and CS3 */
-	ranges = <0 0 0x08000000 0x02000000
-		  1 0 0x0a000000 0x02000000
-		  2 0 0x0c000000 0x02000000
-		  3 0 0x0e000000 0x02000000>;
-
-	/* SRAM on Colibri nEXT_CS0 */
-	sram@0,0 {
-		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
-		reg = <0 0 0x00010000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		bank-width = <2>;
-		fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
-				      0x00000000 0x04000040 0x00000000>;
-	};
-
-	/* SRAM on Colibri nEXT_CS1 */
-	sram@1,0 {
-		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
-		reg = <1 0 0x00010000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		bank-width = <2>;
-		fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
-				      0x00000000 0x04000040 0x00000000>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-apalis-eval.dts b/arch/arm/boot/dts/imx6q-apalis-eval.dts
deleted file mode 100644
index 4665e15b196d..000000000000
--- a/arch/arm/boot/dts/imx6q-apalis-eval.dts
+++ /dev/null
@@ -1,309 +0,0 @@
-/*
- * Copyright 2014-2017 Toradex AG
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
-
-/ {
-	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
-	compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
-		     "fsl,imx6q";
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-		power-supply = <&reg_3v3_sw>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	reg_pcie_switch: regulator-pcie-switch {
-		compatible = "regulator-fixed";
-		regulator-name = "pcie_switch";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		startup-delay-us = <100000>;
-		enable-active-high;
-		status = "okay";
-	};
-
-	reg_3v3_sw: regulator-3v3-sw {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V_SW";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	power-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
-&can1 {
-	xceiver-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
-&can2 {
-	xceiver-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
-	pcie-switch@58 {
-		compatible = "plx,pex8605";
-		reg = <0x58>;
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
-};
-
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
-	vpcie-supply = <&reg_pcie_switch>;
-	status = "okay";
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_spdif {
-	status = "okay";
-};
-
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
-};
-
-/* MMC1 */
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
-	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-/* SD1 */
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
-	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&iomuxc {
-	/*
-	 * Mux the Apalis GPIOs
-	 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
deleted file mode 100644
index a3fa04a97d81..000000000000
--- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
+++ /dev/null
@@ -1,310 +0,0 @@
-/*
- * Copyright 2014-2017 Toradex AG
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
-
-/ {
-	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.1";
-	compatible = "toradex,apalis_imx6q-ixora-v1.1",
-		     "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
-		     "fsl,imx6q";
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds_ixora>;
-
-		led4-green {
-			label = "LED_4_GREEN";
-			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
-		};
-
-		led4-red {
-			label = "LED_4_RED";
-			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-green {
-			label = "LED_5_GREEN";
-			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-red {
-			label = "LED_5_RED";
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
-		};
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
-
-&can1 {
-	status = "okay";
-};
-
-&can2 {
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
-};
-
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
-	status = "okay";
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_spdif {
-	status = "okay";
-};
-
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
-};
-
-/* MMC1 */
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
-	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	status = "okay";
-};
-
-&iomuxc {
-	/*
-	 * Mux the Apalis GPIOs
-	 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-
-	pinctrl_leds_ixora: ledsixoragrp {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
-			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
-			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
deleted file mode 100644
index 5ba49d0f4880..000000000000
--- a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
+++ /dev/null
@@ -1,311 +0,0 @@
-/*
- * Copyright 2014-2017 Toradex AG
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
-
-/ {
-	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board";
-	compatible = "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
-		     "fsl,imx6q";
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds_ixora>;
-
-		led4-green {
-			label = "LED_4_GREEN";
-			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
-		};
-
-		led4-red {
-			label = "LED_4_RED";
-			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-green {
-			label = "LED_5_GREEN";
-			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-red {
-			label = "LED_5_RED";
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
-		};
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
-
-&can1 {
-	status = "okay";
-};
-
-&can2 {
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c02";
-		reg = <0x50>;
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
-};
-
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
-	status = "okay";
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_spdif {
-	status = "okay";
-};
-
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
-};
-
-/* SD1 */
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
-	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&iomuxc {
-	/* Mux the Apalis GPIOs */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-
-	pinctrl_leds_ixora: ledsixoragrp {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
-			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b0
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
-			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
deleted file mode 100644
index 5219553df1e7..000000000000
--- a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
+++ /dev/null
@@ -1,159 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+)
-/*
- * Copyright (C) 2015 DH electronics GmbH
- * Copyright (C) 2018 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-
-#include "imx6q-dhcom-som.dtsi"
-
-/ {
-	model = "Freescale i.MX6 Quad DHCOM Premium Developer Kit (2)";
-	compatible = "dh,imx6q-dhcom-pdk2", "dh,imx6q-dhcom-som", "fsl,imx6q";
-
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	clk_ext_audio_codec: clock-codec {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24000000>;
-	};
-
-	sound {
-		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&sgtl5000>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"LINE_IN", "Line In Jack",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <3>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux_ext>;
-	status = "okay";
-};
-
-&can1 {
-	status = "okay";
-};
-
-&can2 {
-	status = "disabled";
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c2 {
-	sgtl5000: codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		#sound-dai-cells = <0>;
-		clocks = <&clk_ext_audio_codec>;
-		VDDA-supply = <&reg_3p3v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog_base &pinctrl_hog>;
-
-	pinctrl_hog: hog-grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x400120b0
-			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x400120b0
-			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x400120b0
-			MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03	0x400120b0
-			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x120b0
-			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20		0x400120b0
-			MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x120b0
-			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x120b0
-			MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x400120b0
-			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x400120b0
-			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x400120b0
-			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x400120b0
-			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x400120b0
-			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x400120b0
-			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x400120b0
-			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x400120b0
-			MX6QDL_PAD_SD1_CMD__GPIO1_IO18		0x400120b0
-			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16		0x400120b0
-			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x400120b0
-			MX6QDL_PAD_SD1_DAT2__GPIO1_IO19		0x400120b0
-			MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x400120b0
-			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x400120b0
-			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x400120b0
-			MX6QDL_PAD_KEY_COL0__GPIO4_IO06		0x400120b0
-		>;
-	};
-
-	pinctrl_audmux_ext: audmux-ext-grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-		>;
-	};
-
-	pinctrl_enet_1G: enet-1G-grp {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
-			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
-			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
-			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
-			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
-			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
-			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
-			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
-			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
-			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
-			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
-			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
-			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
-			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
-			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x000b0
-			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x000b1
-			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x000b1
-		>;
-	};
-
-	pinctrl_pcie: pcie-grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1
-		>;
-	};
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pcie>;
-	reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&usdhc3 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
deleted file mode 100644
index 845cfad99bf9..000000000000
--- a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
+++ /dev/null
@@ -1,475 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+)
-/*
- * Copyright (C) 2015 DH electronics GmbH
- * Copyright (C) 2018 Marek Vasut <marex@denx.de>
- */
-
-#include "imx6q.dtsi"
-#include <dt-bindings/pwm/pwm.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/imx6qdl-clock.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	aliases {
-		mmc0 = &usdhc2;
-		mmc1 = &usdhc3;
-		mmc2 = &usdhc4;
-		mmc3 = &usdhc1;
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x40000000>;
-	};
-
-	reg_usb_otg_vbus: regulator-usb-otg-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb_otg_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usb_h1_vbus: regulator-usb-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb_h1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_3p3v: regulator-3P3V {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio4 11 GPIO_ACTIVE_HIGH>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	flash@0 {	/* S25FL116K */
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
-		reg = <0>;
-		m25p,fast-read;
-	};
-};
-
-&ecspi2 {
-	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet_100M>;
-	phy-mode = "rmii";
-	phy-handle = <&ethphy0>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy0: ethernet-phy@0 {	/* SMSC LAN8710Ai */
-			reg = <0>;
-			max-speed = <100>;
-			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-			reset-delay-us = <1000>;
-			reset-post-delay-us = <1000>;
-		};
-	};
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	ltc3676: pmic@3c {
-		compatible = "lltc,ltc3676";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pmic_hw300>;
-		reg = <0x3c>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
-
-		regulators {
-			sw1_reg: sw1 {
-				regulator-min-microvolt = <787500>;
-				regulator-max-microvolt = <1527272>;
-				lltc,fb-voltage-divider = <100000 110000>;
-				regulator-suspend-mem-microvolt = <1040000>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw2_reg: sw2 {
-				regulator-min-microvolt = <1885714>;
-				regulator-max-microvolt = <3657142>;
-				lltc,fb-voltage-divider = <100000 28000>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw3_reg: sw3 {
-				regulator-min-microvolt = <787500>;
-				regulator-max-microvolt = <1527272>;
-				lltc,fb-voltage-divider = <100000 110000>;
-				regulator-suspend-mem-microvolt = <980000>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw4_reg: sw4 {
-				regulator-min-microvolt = <855571>;
-				regulator-max-microvolt = <1659291>;
-				lltc,fb-voltage-divider = <100000 93100>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			ldo1_reg: ldo1 {
-				regulator-min-microvolt = <3240306>;
-				regulator-max-microvolt = <3240306>;
-				lltc,fb-voltage-divider = <102000 29400>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			ldo2_reg: ldo2 {
-				regulator-min-microvolt = <2484708>;
-				regulator-max-microvolt = <2484708>;
-				lltc,fb-voltage-divider = <100000 41200>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-		};
-	};
-
-	touchscreen@49 {	/* TSC2004 */
-		compatible = "ti,tsc2004";
-		reg = <0x49>;
-		vio-supply = <&reg_3p3v>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tsc2004_hw300>;
-		interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
-		status = "disabled";
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c02";
-		reg = <0x50>;
-		pagesize = <16>;
-	};
-
-	rtc@56 {
-		compatible = "rv3029c2";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_rtc_hw300>;
-		reg = <0x56>;
-		interrupt-parent = <&gpio7>;
-		interrupts = <12 2>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog_base>;
-
-	pinctrl_hog_base: hog-base-grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0x120b0
-			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x120b0
-			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x120b0
-			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x120b0
-			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x120b0
-		>;
-	};
-
-	pinctrl_ecspi1: ecspi1-grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-		>;
-	};
-
-	pinctrl_ecspi2: ecspi2-grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
-			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
-			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
-			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
-		>;
-	};
-
-	pinctrl_enet_100M: enet-100M-grp {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
-			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
-			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
-			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
-			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
-			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
-			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x000b0
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x000b1
-			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x120b0
-		>;
-	};
-
-	pinctrl_flexcan1: flexcan1-grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
-			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
-		>;
-	};
-
-	pinctrl_flexcan2: flexcan2-grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX	0x1b0b0
-			MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX	0x1b0b0
-		>;
-	};
-
-	pinctrl_i2c1: i2c1-grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-		>;
-	};
-
-	pinctrl_i2c2: i2c2-grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-		>;
-	};
-
-	pinctrl_i2c3: i2c3-grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
-			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-		>;
-	};
-
-	pinctrl_pmic_hw300: pmic-hw300-grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1B0B0
-		>;
-	};
-
-	pinctrl_rtc_hw300: rtc-hw300-grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x120B0
-		>;
-	};
-
-	pinctrl_tsc2004_hw300: tsc2004-hw300-grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x120B0
-		>;
-	};
-
-	pinctrl_uart1: uart1-grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			MX6QDL_PAD_EIM_D20__UART1_RTS_B		0x1b0b1
-			MX6QDL_PAD_EIM_D19__UART1_CTS_B		0x4001b0b1
-			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x4001b0b1
-			MX6QDL_PAD_EIM_D24__GPIO3_IO24		0x4001b0b1
-			MX6QDL_PAD_EIM_D25__GPIO3_IO25		0x4001b0b1
-			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x4001b0b1
-		>;
-	};
-
-	pinctrl_uart4: uart4-grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
-			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart5: uart5-grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
-			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA	0x1b0b1
-			MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B	0x1b0b1
-			MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B	0x4001b0b1
-		>;
-	};
-
-	pinctrl_usbh1: usbh1-grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120B0
-		>;
-	};
-
-	pinctrl_usbotg: usbotg-grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2-grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x120B0
-		>;
-	};
-
-	pinctrl_usdhc3: usdhc3-grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x120B0
-		>;
-	};
-
-	pinctrl_usdhc4: usdhc4-grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
-			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
-			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
-			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
-		>;
-	};
-};
-
-&reg_arm {
-	vin-supply = <&sw3_reg>;
-};
-
-&reg_soc {
-	vin-supply = <&sw1_reg>;
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
-	dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-	dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
-	dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-	rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbh1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1>;
-	vbus-supply = <&reg_usb_h1_vbus>;
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
-	keep-power-in-suspend;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
-	fsl,wp-controller;
-	keep-power-in-suspend;
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	non-removable;
-	bus-width = <8>;
-	no-1-8-v;
-	keep-power-in-suspend;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
deleted file mode 100644
index 47d3ce5d255f..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
+++ /dev/null
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6310 SOM";
-	compatible = "kontron,imx6ul-n6310-som", "fsl,imx6ul";
-
-	memory@80000000 {
-		reg = <0x80000000 0x10000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <108000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x08000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
deleted file mode 100644
index 239a1af3aeaa..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
+++ /dev/null
@@ -1,16 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ul-kontron-n6311-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6311 S";
-	compatible = "kontron,imx6ul-n6311-s", "kontron,imx6ul-n6311-som",
-		     "fsl,imx6ul";
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
deleted file mode 100644
index a095a7654ac6..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6311 SOM";
-	compatible = "kontron,imx6ul-n6311-som", "fsl,imx6ul";
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <104000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x18000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
deleted file mode 100644
index 08669a18349e..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-/dts-v1/;
-
-#include "imx6ull-colibri-nonwifi.dtsi"
-#include "imx6ull-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6ULL 256MB on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx6ull-eval", "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
deleted file mode 100644
index 95a11b8bcbdb..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
+++ /dev/null
@@ -1,24 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-#include "imx6ull-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio6 &pinctrl_gpio7>;
-};
-
-&iomuxc_snvs {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2 &pinctrl_snvs_gpio3>;
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts b/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
deleted file mode 100644
index df72ce1ae2cb..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-/dts-v1/;
-
-#include "imx6ull-colibri-wifi.dtsi"
-#include "imx6ull-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6ULL 512MB on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx6ull-wifi-eval", "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
deleted file mode 100644
index a0545431b3dc..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
+++ /dev/null
@@ -1,52 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-#include "imx6ull-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x20000000>;
-	};
-
-	wifi_pwrseq: sdio-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_wifi_pdn>;
-		reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&cpu0 {
-	clock-frequency = <792000000>;
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio7>;
-
-};
-
-&iomuxc_snvs {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2>;
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
-	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
-	assigned-clock-rates = <0>, <198000000>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	no-1-8-v;
-	non-removable;
-	vmmc-supply = <&reg_module_3v3>;
-	wakeup-source;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
deleted file mode 100644
index 6d850d997e1e..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ /dev/null
@@ -1,611 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-#include "imx6ull.dtsi"
-
-/ {
-	aliases {
-		ethernet0 = &fec2;
-		ethernet1 = &fec1;
-	};
-
-	bl: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
-		status = "disabled";
-	};
-
-	reg_module_3v3: regulator-module-3v3 {
-		compatible = "regulator-fixed";
-		regulator-always-on;
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_module_3v3_avdd: regulator-module-3v3-avdd {
-		compatible = "regulator-fixed";
-		regulator-always-on;
-		regulator-name = "+V3.3_AVDD_AUDIO";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_sd1_vmmc: regulator-sd1-vmmc {
-		compatible = "regulator-gpio";
-		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_reg_sd>;
-		regulator-always-on;
-		regulator-name = "+V3.3_1.8_SD";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		states = <1800000 0x1 3300000 0x0>;
-		vin-supply = <&reg_module_3v3>;
-	};
-};
-
-&adc1 {
-	num-channels = <10>;
-	vref-supply = <&reg_module_3v3_avdd>;
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-	status = "disabled";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "disabled";
-};
-
-/* Colibri SPI */
-&ecspi1 {
-	cs-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
-};
-
-&fec2 {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&pinctrl_enet2>;
-	pinctrl-1 = <&pinctrl_enet2_sleep>;
-	phy-mode = "rmii";
-	phy-handle = <&ethphy1>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy1: ethernet-phy@2 {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			max-speed = <100>;
-			reg = <2>;
-		};
-	};
-};
-
-&gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	nand-on-flash-bbt;
-	nand-ecc-mode = "hw";
-	nand-ecc-strength = <8>;
-	nand-ecc-step-size = <512>;
-	status = "okay";
-};
-
-&i2c1 {
-	pinctrl-names = "default", "gpio";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	pinctrl-1 = <&pinctrl_i2c1_gpio>;
-	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-};
-
-&i2c2 {
-	pinctrl-names = "default", "gpio";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	pinctrl-1 = <&pinctrl_i2c2_gpio>;
-	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	status = "okay";
-
-	ad7879@2c {
-		compatible = "adi,ad7879-1";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_ad7879_int>;
-		reg = <0x2c>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-		touchscreen-max-pressure = <4096>;
-		adi,resistance-plate-x = <120>;
-		adi,first-conversion-delay = /bits/ 8 <3>;
-		adi,acquisition-time = /bits/ 8 <1>;
-		adi,median-filter-size = /bits/ 8 <2>;
-		adi,averaging = /bits/ 8 <1>;
-		adi,conversion-interval = /bits/ 8 <255>;
-	};
-};
-
-&lcdif {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lcdif_dat
-		     &pinctrl_lcdif_ctrl>;
-};
-
-&pwm4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>;
-	#pwm-cells = <3>;
-};
-
-&pwm5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm5>;
-	#pwm-cells = <3>;
-};
-
-&pwm6 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm6>;
-	#pwm-cells = <3>;
-};
-
-&pwm7 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm7>;
-	#pwm-cells = <3>;
-};
-
-&sdma {
-	status = "okay";
-};
-
-&snvs_pwrkey {
-	status = "disabled";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
-	uart-has-rtscts;
-	fsl,dte-mode;
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	uart-has-rtscts;
-	fsl,dte-mode;
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	fsl,dte-mode;
-};
-
-&usbotg1 {
-	dr_mode = "otg";
-	srp-disable;
-	hnp-disable;
-	adp-disable;
-};
-
-&usbotg2 {
-	dr_mode = "host";
-};
-
-&usdhc1 {
-	assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
-	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
-	assigned-clock-rates = <0>, <198000000>;
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-};
-
-&iomuxc {
-	pinctrl_can_int: canint-grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0X14 /* SODIMM 73 */
-		>;
-	};
-
-	pinctrl_enet2: enet2-grp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
-			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
-			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
-			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
-			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
-			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
-			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
-			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
-			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
-			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
-		>;
-	};
-
-	pinctrl_enet2_sleep: enet2sleepgrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO06__GPIO1_IO06	0x0
-			MX6UL_PAD_GPIO1_IO07__GPIO1_IO07	0x0
-			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x0
-			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x0
-			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x0
-			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x0
-			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
-			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11	0x0
-			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12	0x0
-			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x0
-		>;
-	};
-
-	pinctrl_ecspi1_cs: ecspi1-cs-grp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x000a0
-		>;
-	};
-
-	pinctrl_ecspi1: ecspi1-grp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x000a0
-			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x000a0
-			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100a0
-		>;
-	};
-
-	pinctrl_flexcan1: flexcan1-grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX	0x1b020
-			MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX	0x1b020
-		>;
-	};
-
-	pinctrl_flexcan2: flexcan2-grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX	0x1b020
-			MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX	0x1b020
-		>;
-	};
-
-	pinctrl_gpio_bl_on: gpio-bl-on-grp {
-		fsl,pins = <
-			MX6UL_PAD_JTAG_TMS__GPIO1_IO11		0x000a0
-		>;
-	};
-
-	pinctrl_gpio1: gpio1-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0X14 /* SODIMM 77 */
-			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x14 /* SODIMM 99 */
-			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14	0x14 /* SODIMM 133 */
-			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24	0x14 /* SODIMM 135 */
-			MX6UL_PAD_UART3_CTS_B__GPIO1_IO26	0x14 /* SODIMM 100 */
-			MX6UL_PAD_JTAG_TRST_B__GPIO1_IO15	0x14 /* SODIMM 102 */
-			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07	0x14 /* SODIMM 104 */
-			MX6UL_PAD_UART3_RTS_B__GPIO1_IO27	0x14 /* SODIMM 186 */
-		>;
-	};
-
-	pinctrl_gpio2: gpio2-grp { /* Camera */
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x74 /* SODIMM 69 */
-			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x14 /* SODIMM 75 */
-			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x14 /* SODIMM 85 */
-			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x14 /* SODIMM 96 */
-			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x14 /* SODIMM 98 */
-		>;
-	};
-
-	pinctrl_gpio3: gpio3-grp { /* CAN2 */
-		fsl,pins = <
-			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02	0x14 /* SODIMM 178 */
-			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x14 /* SODIMM 188 */
-		>;
-	};
-
-	pinctrl_gpio4: gpio4-grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x74 /* SODIMM 65 */
-		>;
-	};
-
-	pinctrl_gpio5: gpio5-grp { /* ATMEL MXT TOUCH */
-		fsl,pins = <
-			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x74 /* SODIMM 106 */
-		>;
-	};
-
-	pinctrl_gpio6: gpio6-grp { /* Wifi pins */
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x14 /* SODIMM 89 */
-			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x14 /* SODIMM 79 */
-			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x14 /* SODIMM 81 */
-			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x14 /* SODIMM 97 */
-			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x14 /* SODIMM 101 */
-			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x14 /* SODIMM 103 */
-			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x14 /* SODIMM 94 */
-		>;
-	};
-
-	pinctrl_gpio7: gpio7-grp { /* CAN1 */
-		fsl,pins = <
-			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0x74 /* SODIMM 55 */
-			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01	0x74 /* SODIMM 63 */
-		>;
-	};
-
-	pinctrl_gpmi_nand: gpmi-nand-grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x100a9
-			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x100a9
-			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x100a9
-			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x100a9
-			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x100a9
-			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x100a9
-			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x100a9
-			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x100a9
-			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x100a9
-			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x100a9
-			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x100a9
-			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x100a9
-			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x100a9
-			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x100a9
-		>;
-	};
-
-	pinctrl_i2c1: i2c1-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
-			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
-		>;
-	};
-
-	pinctrl_i2c1_gpio: i2c1-gpio-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0
-			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0
-		>;
-	};
-
-	pinctrl_i2c2: i2c2-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
-			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
-		>;
-	};
-
-	pinctrl_i2c2_gpio: i2c2-gpio-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
-			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
-		>;
-	};
-
-	pinctrl_lcdif_dat: lcdif-dat-grp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00  0x00079
-			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01  0x00079
-			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02  0x00079
-			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03  0x00079
-			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04  0x00079
-			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05  0x00079
-			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06  0x00079
-			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07  0x00079
-			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08  0x00079
-			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09  0x00079
-			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10  0x00079
-			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11  0x00079
-			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12  0x00079
-			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13  0x00079
-			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14  0x00079
-			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15  0x00079
-			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16  0x00079
-			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17  0x00079
-		>;
-	};
-
-	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x00079
-			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x00079
-			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC    0x00079
-			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC    0x00079
-		>;
-	};
-
-	pinctrl_pwm4: pwm4-grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_WP_B__PWM4_OUT	0x00079
-		>;
-	};
-
-	pinctrl_pwm5: pwm5-grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_DQS__PWM5_OUT	0x00079
-		>;
-	};
-
-	pinctrl_pwm6: pwm6-grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_TX_EN__PWM6_OUT	0x00079
-		>;
-	};
-
-	pinctrl_pwm7: pwm7-grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT	0x00079
-		>;
-	};
-
-	pinctrl_uart1: uart1-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART1_TX_DATA__UART1_DTE_RX	0x1b0b1
-			MX6UL_PAD_UART1_RX_DATA__UART1_DTE_TX	0x1b0b1
-			MX6UL_PAD_UART1_RTS_B__UART1_DTE_CTS	0x1b0b1
-			MX6UL_PAD_UART1_CTS_B__UART1_DTE_RTS	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart1_ctrl1: uart1-ctrl1-grp { /* Additional DTR, DCD */
-		fsl,pins = <
-			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x1b0b1 /* DCD */
-			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x1b0b1 /* DSR */
-			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x1b0b1 /* DTR */
-			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x1b0b1 /* RI */
-		>;
-	};
-
-	pinctrl_uart2: uart2-grp {
-		fsl,pins = <
-			MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX	0x1b0b1
-			MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX	0x1b0b1
-			MX6UL_PAD_UART2_CTS_B__UART2_DTE_RTS	0x1b0b1
-			MX6UL_PAD_UART2_RTS_B__UART2_DTE_CTS	0x1b0b1
-		>;
-	};
-	pinctrl_uart5: uart5-grp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO04__UART5_DTE_RX	0x1b0b1
-			MX6UL_PAD_GPIO1_IO05__UART5_DTE_TX	0x1b0b1
-		>;
-	};
-
-	pinctrl_usbh_reg: gpio-usbh-reg {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x1b0b1 /* SODIMM 129 USBH PEN */
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1-grp {
-		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x10059
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
-		>;
-	};
-
-	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
-		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170b9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100b9
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
-		>;
-	};
-
-	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
-		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170f9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100f9
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2-grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17059
-			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17059
-			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17059
-			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17059
-			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17059
-			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x17059
-
-			MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT	0x14
-		>;
-	};
-
-	pinctrl_wdog: wdog-grp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY    0x30b0
-		>;
-	};
-};
-
-&iomuxc_snvs {
-	pinctrl_snvs_gpio1: snvs-gpio1-grp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x14 /* SODIMM 93 */
-			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x14 /* SODIMM 95 */
-			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x74 /* SODIMM 105 */
-			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x14 /* SODIMM 131 USBH OC */
-			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x74 /* SODIMM 138 */
-		>;
-	};
-
-	pinctrl_snvs_gpio2: snvs-gpio2-grp { /* ATMEL MXT TOUCH */
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x74 /* SODIMM 107 */
-		>;
-	};
-
-	pinctrl_snvs_gpio3: snvs-gpio3-grp { /* Wifi pins */
-		fsl,pins = <
-			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x14 /* SODIMM 127 */
-		>;
-	};
-
-	pinctrl_snvs_ad7879_int: snvs-ad7879-int-grp { /* TOUCH Interrupt */
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x100b0
-		>;
-	};
-
-	pinctrl_snvs_reg_sd: snvs-reg-sd-grp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400100b0
-		>;
-	};
-
-	pinctrl_snvs_usbc_det: snvs-usbc-det-grp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x130b0
-		>;
-	};
-
-	pinctrl_snvs_gpiokeys: snvs-gpiokeys-grp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130b0
-		>;
-	};
-
-	pinctrl_snvs_usdhc1_cd: snvs-usdhc1-cd-grp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* CD */
-		>;
-	};
-
-	pinctrl_snvs_usdhc1_sleep_cd: snvs-usdhc1-cd-grp-slp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x0
-		>;
-	};
-
-	pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
-		fsl,pins = <
-			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x14
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts b/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
deleted file mode 100644
index 57588a5e1e34..000000000000
--- a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
+++ /dev/null
@@ -1,16 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2019 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ull-kontron-n6411-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6411 S";
-	compatible = "kontron,imx6ull-n6411-s", "kontron,imx6ull-n6411-som",
-		     "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi b/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
deleted file mode 100644
index b7e984284e1a..000000000000
--- a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ull.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6411 SOM";
-	compatible = "kontron,imx6ull-n6311-som", "fsl,imx6ull";
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <104000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x18000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
deleted file mode 100644
index 6aa123cbdadb..000000000000
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ /dev/null
@@ -1,226 +0,0 @@
-/*
- * Copyright 2016 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/ {
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	/* fixed crystal dedicated to mpc258x */
-	clk16m: clk16m {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <16000000>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_5v0: regulator-5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usbh_vbus: regulator-usbh-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh_reg>;
-		regulator-name = "VCC_USB[1-4]";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
-		vin-supply = <&reg_5v0>;
-	};
-};
-
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-
-	status = "okay";
-};
-
-&adc1 {
-	status = "okay";
-};
-
-&adc2 {
-	status = "okay";
-};
-
-&ecspi3 {
-	status = "okay";
-
-	mcp2515: can@0 {
-		compatible = "microchip,mcp2515";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_can_int>;
-		reg = <0>;
-		clocks = <&clk16m>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <10000000>;
-		vdd-supply = <&reg_3v3>;
-		xceiver-supply = <&reg_5v0>;
-		status = "okay";
-	};
-};
-
-&fec1 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiotouch>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc: m41t0m6@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&usbotg1 {
-	status = "okay";
-};
-
-&usdhc1 {
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_gpiotouch: touchgpios {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74
-			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
deleted file mode 100644
index d05be3f0e2a7..000000000000
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ /dev/null
@@ -1,798 +0,0 @@
-/*
- * Copyright 2016 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/ {
-	bl: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm1 0 5000000 0>;
-		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_module_3v3: regulator-module-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	reg_module_3v3_avdd: regulator-module-3v3-avdd {
-		compatible = "regulator-fixed";
-		regulator-name = "+V3.3_AVDD_AUDIO";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "imx7-sgtl5000";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink_master>;
-		simple-audio-card,frame-master = <&dailink_master>;
-		simple-audio-card,cpu {
-			sound-dai = <&sai1>;
-		};
-
-		dailink_master: simple-audio-card,codec {
-			sound-dai = <&codec>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
-		};
-	};
-};
-
-&adc1 {
-	vref-supply = <&reg_DCDC3>;
-};
-
-&adc2 {
-	vref-supply = <&reg_DCDC3>;
-};
-
-&cpu0 {
-	cpu-supply = <&reg_DCDC2>;
-};
-
-&ecspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
-	cs-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
-};
-
-&fec1 {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&pinctrl_enet1>;
-	pinctrl-1 = <&pinctrl_enet1_sleep>;
-	clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
-		<&clks IMX7D_ENET_AXI_ROOT_CLK>,
-		<&clks IMX7D_ENET1_TIME_ROOT_CLK>,
-		<&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
-	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
-	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
-			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
-	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
-	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rmii";
-	phy-supply = <&reg_LDO1>;
-	fsl,magic-packet;
-};
-
-&flexcan1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-	status = "disabled";
-};
-
-&flexcan2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "disabled";
-};
-
-&gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	fsl,use-minimum-ecc;
-	nand-on-flash-bbt;
-	nand-ecc-mode = "hw";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default", "gpio";
-	pinctrl-0 = <&pinctrl_i2c1 &pinctrl_i2c1_int>;
-	pinctrl-1 = <&pinctrl_i2c1_recovery &pinctrl_i2c1_int>;
-	scl-gpios = <&gpio1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	sda-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		#sound-dai-cells = <0>;
-		reg = <0x0a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_sai1_mclk>;
-		VDDA-supply = <&reg_module_3v3_avdd>;
-		VDDIO-supply = <&reg_module_3v3>;
-		VDDD-supply = <&reg_DCDC3>;
-	};
-
-	ad7879@2c {
-		compatible = "adi,ad7879-1";
-		reg = <0x2c>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
-		touchscreen-max-pressure = <4096>;
-		adi,resistance-plate-x = <120>;
-		adi,first-conversion-delay = /bits/ 8 <3>;
-		adi,acquisition-time = /bits/ 8 <1>;
-		adi,median-filter-size = /bits/ 8 <2>;
-		adi,averaging = /bits/ 8 <1>;
-		adi,conversion-interval = /bits/ 8 <255>;
-	};
-
-	pmic@33 {
-		compatible = "ricoh,rn5t567";
-		reg = <0x33>;
-
-		regulators {
-			reg_DCDC1: DCDC1 {  /* V1.0_SOC */
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_DCDC2: DCDC2 { /* V1.1_ARM */
-				regulator-min-microvolt = <975000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_DCDC3: DCDC3 { /* V1.8 */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_DCDC4: DCDC4 { /* V1.35_DRAM */
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_LDO1: LDO1 { /* PWR_EN_+V3.3_ETH */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-			};
-
-			reg_LDO2: LDO2 { /* +V1.8_SD */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_LDO3: LDO3 { /* PWR_EN_+V3.3_LPSR */
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_LDO4: LDO4 { /* V1.8_LPSR */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_LDO5: LDO5 { /* PWR_EN_+V3.3 */
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-		};
-	};
-};
-
-&i2c4 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default", "gpio";
-	pinctrl-0 = <&pinctrl_i2c4>;
-	pinctrl-1 = <&pinctrl_i2c4_recovery>;
-	scl-gpios = <&gpio7 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	sda-gpios = <&gpio7 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-};
-
-&lcdif {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lcdif_dat
-		     &pinctrl_lcdif_ctrl>;
-};
-
-&pwm1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-};
-
-&pwm2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>;
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-};
-
-&pwm4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>;
-};
-
-&reg_1p0d {
-	vin-supply = <&reg_DCDC3>;
-};
-
-&sai1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sai1>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
-	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
-	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	uart-has-rtscts;
-	fsl,dte-mode;
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	assigned-clocks = <&clks IMX7D_UART2_ROOT_SRC>;
-	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	uart-has-rtscts;
-	fsl,dte-mode;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
-	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	fsl,dte-mode;
-};
-
-&usbotg1 {
-	dr_mode = "host";
-};
-
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
-	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	vqmmc-supply = <&reg_LDO2>;
-};
-
-&usdhc3 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
-	assigned-clock-rates = <400000000>;
-	bus-width = <8>;
-	fsl,tuning-step = <2>;
-	max-frequency = <100000000>;
-	vmmc-supply = <&reg_module_3v3>;
-	vqmmc-supply = <&reg_DCDC3>;
-	non-removable;
-	sdhci-caps-mask = <0x80000000 0x0>;
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4
-		     &pinctrl_gpio7>;
-
-	pinctrl_gpio1: gpio1-grp {
-		fsl,pins = <
-			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
-			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
-			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
-			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14 /* SODIMM 93 */
-			MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x14 /* SODIMM 95 */
-			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11	0x14 /* SODIMM 99 */
-			MX7D_PAD_EPDC_DATA10__GPIO2_IO10	0x74 /* SODIMM 105 */
-			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x74 /* SODIMM 107 */
-			MX7D_PAD_EPDC_DATA00__GPIO2_IO0		0x14 /* SODIMM 111 */
-			MX7D_PAD_EPDC_DATA01__GPIO2_IO1		0x14 /* SODIMM 113 */
-			MX7D_PAD_EPDC_DATA02__GPIO2_IO2		0x14 /* SODIMM 115 */
-			MX7D_PAD_EPDC_DATA03__GPIO2_IO3		0x14 /* SODIMM 117 */
-			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x14 /* SODIMM 119 */
-			MX7D_PAD_EPDC_DATA05__GPIO2_IO5		0x14 /* SODIMM 121 */
-			MX7D_PAD_EPDC_DATA06__GPIO2_IO6		0x14 /* SODIMM 123 */
-			MX7D_PAD_EPDC_DATA07__GPIO2_IO7		0x14 /* SODIMM 125 */
-			MX7D_PAD_EPDC_SDCE2__GPIO2_IO22		0x14 /* SODIMM 127 */
-			MX7D_PAD_UART3_RTS_B__GPIO4_IO6		0x14 /* SODIMM 131 */
-			MX7D_PAD_EPDC_GDRL__GPIO2_IO26		0x14 /* SODIMM 133 */
-			MX7D_PAD_SAI1_RX_DATA__GPIO6_IO12	0x14 /* SODIMM 169 */
-			MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17	0x14 /* SODIMM 24 */
-			MX7D_PAD_SD2_DATA2__GPIO5_IO16		0x14 /* SODIMM 100 */
-			MX7D_PAD_SD2_DATA3__GPIO5_IO17		0x14 /* SODIMM 102 */
-			MX7D_PAD_EPDC_GDSP__GPIO2_IO27		0x14 /* SODIMM 104 */
-			MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x74 /* SODIMM 106 */
-			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x14 /* SODIMM 110 */
-			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x14 /* SODIMM 112 */
-			MX7D_PAD_EPDC_SDCLK__GPIO2_IO16		0x14 /* SODIMM 114 */
-			MX7D_PAD_EPDC_SDLE__GPIO2_IO17		0x14 /* SODIMM 116 */
-			MX7D_PAD_EPDC_SDOE__GPIO2_IO18		0x14 /* SODIMM 118 */
-			MX7D_PAD_EPDC_SDSHR__GPIO2_IO19		0x14 /* SODIMM 120 */
-			MX7D_PAD_EPDC_SDCE0__GPIO2_IO20		0x14 /* SODIMM 122 */
-			MX7D_PAD_EPDC_SDCE1__GPIO2_IO21		0x14 /* SODIMM 124 */
-			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x14 /* SODIMM 126 */
-			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x14 /* SODIMM 128 */
-			MX7D_PAD_EPDC_SDCE3__GPIO2_IO23		0x14 /* SODIMM 130 */
-			MX7D_PAD_EPDC_GDCLK__GPIO2_IO24		0x14 /* SODIMM 132 */
-			MX7D_PAD_EPDC_GDOE__GPIO2_IO25		0x14 /* SODIMM 134 */
-			MX7D_PAD_EPDC_DATA12__GPIO2_IO12	0x14 /* SODIMM 150 */
-			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x14 /* SODIMM 152 */
-			MX7D_PAD_SD2_CLK__GPIO5_IO12		0x14 /* SODIMM 184 */
-			MX7D_PAD_SD2_CMD__GPIO5_IO13		0x14 /* SODIMM 186 */
-		>;
-	};
-
-	pinctrl_gpio2: gpio2-grp { /* On X22 Camera interface */
-		fsl,pins = <
-			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x14 /* SODIMM 65 */
-			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x74 /* SODIMM 69 */
-			MX7D_PAD_I2C4_SDA__GPIO4_IO15		0x14 /* SODIMM 75 */
-			MX7D_PAD_ECSPI1_MISO__GPIO4_IO18	0x14 /* SODIMM 79 */
-			MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x14 /* SODIMM 81 */
-			MX7D_PAD_ECSPI2_MISO__GPIO4_IO22	0x14 /* SODIMM 85 */
-			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19		0x14 /* SODIMM 97 */
-			MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16	0x14 /* SODIMM 101 */
-			MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17	0x14 /* SODIMM 103 */
-			MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x14 /* SODIMM 94 */
-			MX7D_PAD_I2C4_SCL__GPIO4_IO14		0x14 /* SODIMM 96 */
-			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14 /* SODIMM 98 */
-		>;
-	};
-
-	pinctrl_gpio3: gpio3-grp { /* LCD 18-23 */
-		fsl,pins = <
-			MX7D_PAD_LCD_DATA18__GPIO3_IO23		0x14 /* SODIMM 136 */
-			MX7D_PAD_LCD_DATA19__GPIO3_IO24		0x14 /* SODIMM 138 */
-			MX7D_PAD_LCD_DATA20__GPIO3_IO25		0x14 /* SODIMM 140 */
-			MX7D_PAD_LCD_DATA21__GPIO3_IO26		0x14 /* SODIMM 142 */
-			MX7D_PAD_LCD_DATA22__GPIO3_IO27		0x74 /* SODIMM 144 */
-			MX7D_PAD_LCD_DATA23__GPIO3_IO28		0x74 /* SODIMM 146 */
-		>;
-	};
-
-	pinctrl_gpio4: gpio4-grp { /* Alternatively CAN2 */
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO15__GPIO1_IO15		0x14 /* SODIMM 178 */
-			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x14 /* SODIMM 188 */
-		>;
-	};
-
-	pinctrl_gpio7: gpio7-grp { /* Alternatively CAN1 */
-		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x14 /* SODIMM 55 */
-			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x14 /* SODIMM 63 */
-		>;
-	};
-
-	pinctrl_i2c1_int: i2c1-int-grp { /* PMIC / TOUCH */
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x79
-		>;
-	};
-
-	pinctrl_can_int: can-int-grp {
-		fsl,pins = <
-			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
-		>;
-	};
-
-	pinctrl_enet1: enet1grp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_CRS__GPIO7_IO14			0x14
-			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x73
-			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x73
-			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x73
-			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER		0x73
-
-			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x73
-			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x73
-			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x73
-			MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1		0x73
-			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x3
-			MX7D_PAD_SD2_WP__ENET1_MDC			0x3
-		>;
-	};
-
-	pinctrl_enet1_sleep: enet1sleepgrp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4		0x0
-			MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0		0x0
-			MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1		0x0
-			MX7D_PAD_ENET1_RGMII_RXC__GPIO7_IO5		0x0
-
-			MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10		0x0
-			MX7D_PAD_ENET1_RGMII_TD0__GPIO7_IO6		0x0
-			MX7D_PAD_ENET1_RGMII_TD1__GPIO7_IO7		0x0
-			MX7D_PAD_GPIO1_IO12__GPIO1_IO12			0x0
-			MX7D_PAD_SD2_CD_B__GPIO5_IO9			0x0
-			MX7D_PAD_SD2_WP__GPIO5_IO10			0x0
-		>;
-	};
-
-	pinctrl_ecspi3_cs: ecspi3-cs-grp {
-		fsl,pins = <
-			MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x14
-		>;
-	};
-
-	pinctrl_ecspi3: ecspi3-grp {
-		fsl,pins = <
-			MX7D_PAD_I2C1_SCL__ECSPI3_MISO		0x2
-			MX7D_PAD_I2C1_SDA__ECSPI3_MOSI		0x2
-			MX7D_PAD_I2C2_SCL__ECSPI3_SCLK		0x2
-		>;
-	};
-
-	pinctrl_flexcan1: flexcan1-grp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX	0x79 /* SODIMM 55 */
-			MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX	0x79 /* SODIMM 63 */
-		>;
-	};
-
-	pinctrl_flexcan2: flexcan2-grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x79 /* SODIMM 188 */
-			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x79 /* SODIMM 178 */
-		>;
-	};
-
-	pinctrl_gpio_bl_on: gpio-bl-on {
-		fsl,pins = <
-			MX7D_PAD_SD1_WP__GPIO5_IO1		0x14 /* SODIMM 71 */
-		>;
-	};
-
-	pinctrl_gpmi_nand: gpmi-nand-grp {
-		fsl,pins = <
-			MX7D_PAD_SD3_CLK__NAND_CLE		0x71
-			MX7D_PAD_SD3_CMD__NAND_ALE		0x71
-			MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	0x71
-			MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	0x74
-			MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
-			MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
-			MX7D_PAD_SD3_DATA0__NAND_DATA00		0x71
-			MX7D_PAD_SD3_DATA1__NAND_DATA01		0x71
-			MX7D_PAD_SD3_DATA2__NAND_DATA02		0x71
-			MX7D_PAD_SD3_DATA3__NAND_DATA03		0x71
-			MX7D_PAD_SD3_DATA4__NAND_DATA04		0x71
-			MX7D_PAD_SD3_DATA5__NAND_DATA05		0x71
-			MX7D_PAD_SD3_DATA6__NAND_DATA06		0x71
-			MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
-		>;
-	};
-
-	pinctrl_i2c4: i2c4-grp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA	0x4000007f
-			MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL	0x4000007f
-		>;
-	};
-
-	pinctrl_i2c4_recovery: i2c4-recoverygrp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_TD2__GPIO7_IO8	0x4000007f
-			MX7D_PAD_ENET1_RGMII_TD3__GPIO7_IO9	0x4000007f
-		>;
-	};
-
-	pinctrl_lcdif_dat: lcdif-dat-grp {
-		fsl,pins = <
-			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79
-			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79
-			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79
-			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79
-			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79
-			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79
-			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79
-			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79
-			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79
-			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79
-			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79
-			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79
-			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79
-			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79
-			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79
-			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79
-			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79
-			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79
-		>;
-	};
-
-	pinctrl_lcdif_dat_24: lcdif-dat-24-grp {
-		fsl,pins = <
-			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79
-			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79
-			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79
-			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79
-			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79
-			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79
-		>;
-	};
-
-	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
-		fsl,pins = <
-			MX7D_PAD_LCD_CLK__LCD_CLK		0x79
-			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79
-			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79
-			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79
-		>;
-	};
-
-	pinctrl_pwm1: pwm1-grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO08__PWM1_OUT		0x79
-			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x4
-		>;
-	};
-
-	pinctrl_pwm2: pwm2-grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__PWM2_OUT		0x79
-		>;
-	};
-
-	pinctrl_pwm3: pwm3-grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__PWM3_OUT		0x79
-		>;
-	};
-
-	pinctrl_pwm4: pwm4-grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO11__PWM4_OUT		0x79
-			MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20	0x4
-		>;
-	};
-
-	pinctrl_uart1: uart1-grp {
-		fsl,pins = <
-			MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX	0x79
-			MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX	0x79
-			MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS	0x79
-			MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS	0x79
-		>;
-	};
-
-	pinctrl_uart1_ctrl1: uart1-ctrl1-grp {
-		fsl,pins = <
-			MX7D_PAD_SD2_DATA1__GPIO5_IO15		0x14 /* DCD */
-			MX7D_PAD_SD2_DATA0__GPIO5_IO14		0x14 /* DTR */
-		>;
-	};
-
-	pinctrl_uart2: uart2-grp {
-		fsl,pins = <
-			MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX 0x79
-			MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX 0x79
-			MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS 0x79
-			MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS 0x79
-		>;
-	};
-	pinctrl_uart3: uart3-grp {
-		fsl,pins = <
-			MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX 0x79
-			MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX 0x79
-		>;
-	};
-
-	pinctrl_usbh_reg: gpio-usbh-vbus {
-		fsl,pins = <
-			MX7D_PAD_UART3_CTS_B__GPIO4_IO7	0x14 /* SODIMM 129 USBH PEN */
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1-grp {
-		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x59
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x19
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x59
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x59
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x59
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x59
-		>;
-	};
-
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
-		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5a
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1a
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5a
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5a
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5a
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5a
-		>;
-	};
-
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
-		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5b
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1b
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5b
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5b
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5b
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5b
-		>;
-	};
-
-	pinctrl_usdhc3: usdhc3grp {
-		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
-			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
-			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
-			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
-			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
-			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
-			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
-			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
-			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
-			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
-			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x19
-		>;
-	};
-
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
-		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
-			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
-			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
-			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
-			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
-			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5a
-			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5a
-			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5a
-			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5a
-			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5a
-			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1a
-		>;
-	};
-
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
-		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
-			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
-			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
-			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
-			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
-			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5b
-			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5b
-			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5b
-			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5b
-			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5b
-			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1b
-		>;
-	};
-
-	pinctrl_sai1: sai1-grp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
-			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x1f
-			MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
-			MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
-		>;
-	};
-
-	pinctrl_sai1_mclk: sai1grp_mclk {
-		fsl,pins = <
-			MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
-		>;
-	};
-};
-
-&iomuxc_lpsr {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio_lpsr>;
-
-	pinctrl_gpio_lpsr: gpio1-grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59
-			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59
-		>;
-	};
-
-	pinctrl_gpiokeys: gpiokeysgrp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x19
-		>;
-	};
-
-	pinctrl_i2c1: i2c1-grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
-			MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL	0x4000007f
-		>;
-	};
-
-	pinctrl_i2c1_recovery: i2c1-recoverygrp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4	0x4000007f
-			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x4000007f
-		>;
-	};
-
-	pinctrl_cd_usdhc1: usdhc1-cd-grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* CD */
-		>;
-	};
-
-	pinctrl_uart1_ctrl2: uart1-ctrl2-grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x14 /* DSR */
-			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14 /* RI */
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi b/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
deleted file mode 100644
index 898f4b8d7421..000000000000
--- a/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
+++ /dev/null
@@ -1,22 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2017 Toradex AG
- */
-
-#include "imx7d.dtsi"
-#include "imx7-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>;
-	};
-};
-
-&usbotg2 {
-	dr_mode = "host";
-};
-
-&usdhc3 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
deleted file mode 100644
index 136e11ab4893..000000000000
--- a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * Copyright 2016 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx7d-colibri.dtsi"
-#include "imx7-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX7D on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx7d-eval-v3", "toradex,colibri-imx7d",
-		     "fsl,imx7d";
-};
-
-&usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx7d-colibri.dtsi b/arch/arm/boot/dts/imx7d-colibri.dtsi
deleted file mode 100644
index e2e327f437e3..000000000000
--- a/arch/arm/boot/dts/imx7d-colibri.dtsi
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright 2016 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "imx7d.dtsi"
-#include "imx7-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x20000000>;
-	};
-};
-
-&gpmi {
-	status = "okay";
-};
-
-&usbotg2 {
-	dr_mode = "host";
-};
diff --git a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
deleted file mode 100644
index bd2a49c1ade6..000000000000
--- a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * Copyright 2016 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx7s-colibri.dtsi"
-#include "imx7-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX7S on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx7s-eval-v3", "toradex,colibri-imx7s",
-		     "fsl,imx7s";
-};
diff --git a/arch/arm/boot/dts/imx7s-colibri.dtsi b/arch/arm/boot/dts/imx7s-colibri.dtsi
deleted file mode 100644
index 1fb1ec5d3d70..000000000000
--- a/arch/arm/boot/dts/imx7s-colibri.dtsi
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * Copyright 2016 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "imx7s.dtsi"
-#include "imx7-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>;
-	};
-};
diff --git a/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts b/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts
deleted file mode 100644
index 8fcd95805ff4..000000000000
--- a/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts
+++ /dev/null
@@ -1,109 +0,0 @@
-// SPDX-License-Identifier: ISC
-/*
- * Device Tree file for Linksys NSLU2
- */
-
-/dts-v1/;
-
-#include "intel-ixp42x.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
-	model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)";
-	compatible = "linksys,nslu2", "intel,ixp42x";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	memory@0 {
-		/* 32 MB SDRAM */
-		device_type = "memory";
-		reg = <0x00000000 0x2000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
-		stdout-path = "uart0:115200n8";
-	};
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		led-status {
-			label = "nslu2:red:status";
-			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-			linux,default-trigger = "heartbeat";
-		};
-		led-ready {
-			label = "nslu2:green:ready";
-			gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-		led-disk-1 {
-			label = "nslu2:green:disk-1";
-			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-		led-disk-2 {
-			label = "nslu2:green:disk-2";
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-
-		button-power {
-			wakeup-source;
-			linux,code = <KEY_POWER>;
-			label = "power";
-			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
-		};
-		button-reset {
-			wakeup-source;
-			linux,code = <KEY_ESC>;
-			label = "reset";
-			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	i2c {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		rtc@6f {
-			compatible = "xicor,x1205";
-			reg = <0x6f>;
-		};
-	};
-
-	gpio-poweroff {
-		compatible = "gpio-poweroff";
-		gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
-		timeout-ms = <5000>;
-	};
-
-	/* The first 16MB region on the expansion bus */
-	flash@50000000 {
-		compatible = "intel,ixp4xx-flash", "cfi-flash";
-		bank-width = <2>;
-		/*
-		 * 8 MB of Flash in 0x20000 byte blocks
-		 * mapped in at 0x50000000
-		 */
-		reg = <0x50000000 0x800000>;
-
-		partitions {
-			compatible = "redboot-fis";
-			/* Eraseblock at 0x7e0000 */
-			fis-index-block = <0x3f>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358.dts b/arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358.dts
deleted file mode 100644
index ba1163a1e1e7..000000000000
--- a/arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358.dts
+++ /dev/null
@@ -1,94 +0,0 @@
-// SPDX-License-Identifier: ISC
-/*
- * Device Tree file for Gateworks IXP43x-based Cambria GW2358
- */
-
-/dts-v1/;
-
-#include "intel-ixp43x.dtsi"
-
-/ {
-	model = "Gateworks Cambria GW2358";
-	compatible = "gateworks,gw2358", "intel,ixp43x";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	memory@0 {
-		/* 128 MB SDRAM */
-		device_type = "memory";
-		reg = <0x00000000 0x8000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
-		stdout-path = "uart0:115200n8";
-	};
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		led-user {
-			label = "gw2358:green:LED";
-			gpios = <&pld1 0 GPIO_ACTIVE_LOW>;
-			default-state = "on";
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-
-	i2c {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hwmon@28 {
-			compatible = "adi,ad7418";
-			reg = <0x28>;
-		};
-		rtc: ds1672@68 {
-			compatible = "dallas,ds1672";
-			reg = <0x68>;
-		};
-		eeprom@51 {
-			compatible = "atmel,24c08";
-			reg = <0x51>;
-			pagesize = <16>;
-			size = <1024>;
-			read-only;
-		};
-		pld0: pld@56 {
-			compatible = "gateworks,pld-gpio";
-			reg = <0x56>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-		/* This PLD just handles the LED and user button */
-		pld1: pld@57 {
-			compatible = "gateworks,pld-gpio";
-			reg = <0x57>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-	};
-
-	flash@50000000 {
-		compatible = "intel,ixp4xx-flash", "cfi-flash";
-		bank-width = <2>;
-		/*
-		 * 32 MB of Flash in 0x20000 byte blocks
-		 * mapped in at 0x50000000
-		 */
-		reg = <0x50000000 0x2000000>;
-
-		partitions {
-			compatible = "redboot-fis";
-			/* Eraseblock at 0x1fe0000 */
-			fis-index-block = <0xff>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi b/arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi
deleted file mode 100644
index f8cd506659dc..000000000000
--- a/arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi
+++ /dev/null
@@ -1,34 +0,0 @@
-// SPDX-License-Identifier: ISC
-/*
- * Device Tree file for Intel XScale Network Processors
- * in the IXP45x and IXP46x series. This series has 64 interrupts and adds a
- * few more peripherals over the 42x and 43x series so this extends the
- * basic IXP4xx DTSI.
- */
-#include "intel-ixp4xx.dtsi"
-
-/ {
-	soc {
-		interrupt-controller@c8003000 {
-			compatible = "intel,ixp43x-interrupt";
-		};
-
-		/*
-		 * This is the USB Device Mode (UDC) controller, which is used
-		 * to present the IXP4xx as a device on a USB bus.
-		 */
-		usb@c800b000 {
-			compatible = "intel,ixp4xx-udc";
-			reg = <0xc800b000 0x1000>;
-			interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		i2c@c8011000 {
-			compatible = "intel,ixp4xx-i2c";
-			reg = <0xc8011000 0x18>;
-			interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/intel-ixp4xx.dtsi b/arch/arm/boot/dts/intel-ixp4xx.dtsi
deleted file mode 100644
index d4a09584f417..000000000000
--- a/arch/arm/boot/dts/intel-ixp4xx.dtsi
+++ /dev/null
@@ -1,69 +0,0 @@
-// SPDX-License-Identifier: ISC
-/*
- * Device Tree file for Intel XScale Network Processors
- * in the IXP 4xx series.
- */
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-		interrupt-parent = <&intcon>;
-
-		qmgr: queue-manager@60000000 {
-			compatible = "intel,ixp4xx-ahb-queue-manager";
-			reg = <0x60000000 0x4000>;
-			interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		uart0: serial@c8000000 {
-			compatible = "intel,xscale-uart";
-			reg = <0xc8000000 0x1000>;
-			/*
-			 * The reg-offset and reg-shift is a side effect
-			 * of running the platform in big endian mode.
-			 */
-			reg-offset = <3>;
-			reg-shift = <2>;
-			interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
-			clock-frequency = <14745600>;
-			no-loopback-test;
-		};
-
-		gpio0: gpio@c8004000 {
-			compatible = "intel,ixp4xx-gpio";
-			reg = <0xc8004000 0x1000>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		intcon: interrupt-controller@c8003000 {
-			/*
-			 * Note: no compatible string. The subvariant of the
-			 * chip needs to define what version it is. The
-			 * location of the interrupt controller is fixed in
-			 * memory across all variants.
-			 */
-			reg = <0xc8003000 0x100>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		timer@c8005000 {
-			compatible = "intel,ixp4xx-timer";
-			reg = <0xc8005000 0x100>;
-			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		npe@c8006000 {
-			compatible = "intel,ixp4xx-network-processing-engine";
-			reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/intel/Makefile b/arch/arm/boot/dts/intel/Makefile
new file mode 100644
index 000000000000..c5fc845deb61
--- /dev/null
+++ b/arch/arm/boot/dts/intel/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += axm
+subdir-y += ixp
+subdir-y += pxa
+subdir-y += socfpga
diff --git a/arch/arm/boot/dts/intel/axm/Makefile b/arch/arm/boot/dts/intel/axm/Makefile
new file mode 100644
index 000000000000..7c7dc679964d
--- /dev/null
+++ b/arch/arm/boot/dts/intel/axm/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_AXXIA) += \
+	axm5516-amarillo.dtb
+dtb-$(CONFIG_ARCH_AXXIA) += \
+	axm5516-amarillo.dtb
diff --git a/arch/arm/boot/dts/axm5516-amarillo.dts b/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts
index 2e2ad3c7ee77..2e2ad3c7ee77 100644
--- a/arch/arm/boot/dts/axm5516-amarillo.dts
+++ b/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts
diff --git a/arch/arm/boot/dts/axm5516-cpus.dtsi b/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi
index 3bcf4e0a3c85..f13ef80b6637 100644
--- a/arch/arm/boot/dts/axm5516-cpus.dtsi
+++ b/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi
@@ -73,7 +73,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x00>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -81,7 +81,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x01>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -89,7 +89,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x02>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -97,7 +97,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x03>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -105,7 +105,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x100>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -113,7 +113,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x101>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -121,7 +121,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x102>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -129,7 +129,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x103>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -137,7 +137,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x200>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -145,7 +145,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x201>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -153,7 +153,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x202>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -161,7 +161,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x203>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -169,7 +169,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x300>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -177,7 +177,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x301>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -185,7 +185,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x302>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -193,7 +193,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x303>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 	};
diff --git a/arch/arm/boot/dts/axm55xx.dtsi b/arch/arm/boot/dts/intel/axm/axm55xx.dtsi
index 7676a65059a4..5277890cfad2 100644
--- a/arch/arm/boot/dts/axm55xx.dtsi
+++ b/arch/arm/boot/dts/intel/axm/axm55xx.dtsi
@@ -108,7 +108,7 @@
 			#size-cells = <2>;
 			ranges;
 
-			serial0: uart@2010080000 {
+			serial0: serial@2010080000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10080000 0 0x1000>;
 				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
@@ -117,7 +117,7 @@
 				status = "disabled";
 			};
 
-			serial1: uart@2010081000 {
+			serial1: serial@2010081000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10081000 0 0x1000>;
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
@@ -126,7 +126,7 @@
 				status = "disabled";
 			};
 
-			serial2: uart@2010082000 {
+			serial2: serial@2010082000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10082000 0 0x1000>;
 				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
@@ -135,7 +135,7 @@
 				status = "disabled";
 			};
 
-			serial3: uart@2010083000 {
+			serial3: serial@2010083000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10083000 0 0x1000>;
 				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/intel/ixp/Makefile b/arch/arm/boot/dts/intel/ixp/Makefile
new file mode 100644
index 000000000000..ab8525f1ea1d
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/Makefile
@@ -0,0 +1,20 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_IXP4XX) += \
+	intel-ixp42x-linksys-nslu2.dtb \
+	intel-ixp42x-linksys-wrv54g.dtb \
+	intel-ixp42x-freecom-fsg-3.dtb \
+	intel-ixp42x-welltech-epbx100.dtb \
+	intel-ixp42x-ixdp425.dtb \
+	intel-ixp43x-kixrp435.dtb \
+	intel-ixp46x-ixdp465.dtb \
+	intel-ixp42x-adi-coyote.dtb \
+	intel-ixp42x-ixdpg425.dtb \
+	intel-ixp42x-goramo-multilink.dtb \
+	intel-ixp42x-iomega-nas100d.dtb \
+	intel-ixp42x-dlink-dsm-g600.dtb \
+	intel-ixp42x-gateworks-gw2348.dtb \
+	intel-ixp43x-gateworks-gw2358.dtb \
+	intel-ixp42x-netgear-wg302v1.dtb \
+	intel-ixp42x-arcom-vulcan.dtb \
+	intel-ixp42x-gateway-7001.dtb \
+	intel-ixp42x-usrobotics-usr8200.dtb
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts
new file mode 100644
index 000000000000..765ab36e6f0c
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for ADI Engineering Coyote platform.
+ * Derived from boardfiles written by MontaVista software.
+ * Ethernet set-up from OpenWrt.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ADI Engineering Coyote reference design";
+	compatible = "adieng,coyote", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* CHECKME: 16 MB SDRAM minimum, maybe the Coyote actually has more */
+		device_type = "memory";
+		reg = <0x00000000 0x01000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+		stdout-path = "uart1:115200n8";
+	};
+
+	aliases {
+		/* These are switched around */
+		serial0 = &uart1;
+		serial1 = &uart0;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 32 MB of Flash in 128 0x20000 sized blocks
+				 * mapped in at CS0 and CS1
+				 */
+				reg = <0 0x00000000 0x2000000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* CHECKME: guess this is Redboot FIS */
+					fis-index-block = <0x1ff>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from Coyote PCI boardfile.
+			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+			 * each handling all IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 6 */
+			<0x0800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 6 */
+			<0x0800 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 6 */
+			<0x0800 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 6 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */
+			<0x1000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 11 */
+			<0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */
+			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 11 */
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy4: ethernet-phy@4 {
+					reg = <4>;
+				};
+
+				phy5: ethernet-phy@5 {
+					reg = <5>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy4>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts
new file mode 100644
index 000000000000..6f5b4e4eb1cc
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Arcom/Eurotech Vulcan board.
+ * This board is a single board computer in the PC/104 form factor based on
+ * IXP425, and was released around 2005. It previously had the name "Mercury".
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Arcom/Eurotech Vulcan";
+	compatible = "arcom,vulcan", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		/* CHECKME: using a harddrive at /dev/sda1 as rootfs by default */
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 32 MB of Flash in 0x20000 byte blocks
+				 * mapped in at CS0 and CS1.
+				 *
+				 * The documentation mentions the existence
+				 * of a 16MB version, which we conveniently
+				 * ignore. Shout if you own one!
+				 */
+				reg = <0 0x00000000 0x2000000>;
+
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-t3 = <3>;
+				intel,ixp4xx-eb-byte-access-on-halfword = <1>;
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					fis-index-block = <0x1ff>;
+				};
+			};
+			sram@2,0 {
+				/* 256 KB SDRAM memory at CS2 */
+				compatible = "shared-dma-pool";
+				device_type = "memory";
+				reg = <2 0x00000000 0x40000>;
+				no-map;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-t3 = <1>;
+				intel,ixp4xx-eb-t4 = <2>;
+				intel,ixp4xx-eb-ahb-split-transfers = <1>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+			};
+			serial@3,0 {
+				/*
+				 * 8250-compatible Exar XR16L2551 2 x UART
+				 *
+				 * CHECKME: if special tweaks are needed, then fix the
+				 * operating system to handle it.
+				 */
+				compatible = "exar,xr16l2551", "ns8250";
+				reg = <3 0x00000000 0x10>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+				clock-frequency = <1843200>;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-t3 = <3>;
+				intel,ixp4xx-eb-cycle-type = <1>; /* Motorola cycles */
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+			};
+			gpio1: gpio@4,0 {
+				/*
+				 * MMIO GPIO in one byte
+				 */
+				compatible = "arcom,vulcan-gpio";
+				reg = <4 0x00000000 0x1>;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+			};
+			watchdog@5,0 {
+				compatible = "maxim,max6369";
+				reg = <5 0x00000000 0x1>;
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from Vulcan PCI boardfile.
+			 *
+			 * We have 2 slots (IDSEL) 1 and 2 with one dedicated interrupt
+			 * per slot. This interrupt is shared (OR:ed) by all four pins.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 2 */
+			<0x0800 0 0 2 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 2 */
+			<0x0800 0 0 3 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 2 */
+			<0x0800 0 0 4 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 2 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 3 */
+			<0x1000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 3 */
+			<0x1000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 3 */
+			<0x1000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 3 */
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts
new file mode 100644
index 000000000000..fa133c913606
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for D-Link DSM-G600 revision A based on IXP420
+ * NOTE: revision B of this device uses PowerPC and is NOT supported by
+ * this device tree.
+ *
+ * Inspired by the boardfile by Rod Whitby, Tower Technologies, Alessandro Zummo
+ * and Michael Westerhof.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "D-Link DSM-G600 rev A";
+	compatible = "dlink,dsm-g600-a", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 64 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-power {
+			label = "dsmg600:green:power";
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		led-wlan {
+			label = "dsmg600:green:wlan";
+			/* CHECKME: flagged as active low in the old board file */
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			/* We don't have WLAN trigger in the kernel (yet) */
+			linux,default-trigger = "netdev";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_keys_polled {
+		compatible = "gpio-keys-polled";
+
+		/*
+		 * According to the board file this key cannot handle interrupts and
+		 * need to be polled. Investigate if this is really the case or if
+		 * this can be moved adjacent to the ordinary gpio-keys above.
+		 */
+		button-power {
+			wakeup-source;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+		timeout-ms = <5000>;
+	};
+
+	soc {
+		bus@c4000000 {
+			/* The first 16MB region at CS0 on the expansion bus */
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 16 MB of Flash in 128 0x20000 sized blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/*
+					 * A boot log says the directory is at 0xfe0000
+					 * 0x7f * 0x20000 = 0xfe0000
+					 */
+					fis-index-block = <0x7f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from DSM-G600 PCI boardfile (dsmg600-pci.c)
+			 * We have slots (IDSEL) 1, 2, 3, 4 and pins 1, 2 and 3.
+			 * Only slot 3 have three IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 7  IRQ_TYPE_LEVEL_LOW>, /* INT E on slot 1 is irq 7 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 10 */
+			<0x1800 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 9 */
+			<0x1800 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 8 */
+			/* IDSEL 4 */
+			<0x2000 0 0 3 &gpio0 6  IRQ_TYPE_LEVEL_LOW>; /* INT F on slot 4 is irq 6 */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts
new file mode 100644
index 000000000000..73d3c11dd0d4
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts
@@ -0,0 +1,219 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Freecom FSG-3 router.
+ * This machine is based on IXP425.
+ * This device tree is inspired by the board file by Rod Whitby.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Freecom FSG-3";
+	compatible = "freecom,fsg-3", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 64 MB memory */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		/* Boot from the first partition on the hard drive */
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-sync {
+			wakeup-source;
+			/* Closest approximation of what the key should do */
+			linux,code = <KEY_CONNECT>;
+			label = "sync";
+			gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		};
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+		};
+		button-usb {
+			wakeup-source;
+			/* Unplug USB, closest approximation of what the key should do */
+			linux,code = <KEY_EJECTCD>;
+			label = "usb";
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hwmon@28 {
+			/*
+			 * Temperature sensor and fan control chip.
+			 *
+			 * TODO: create a proper device tree binding for
+			 * the sensor and temperature zone and create a
+			 * zone with fan control.
+			 */
+			compatible = "winbond,w83781d";
+			reg = <0x28>;
+		};
+		rtc@6f {
+			compatible = "isil,isl1208";
+			reg = <0x6f>;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 4 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x400000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x3e0000 */
+					fis-index-block = <0x1f>;
+				};
+			};
+
+			/* Small syscon with some LEDs at CS2 */
+			syscon@2,0 {
+				compatible = "freecom,fsg-cs2-system-controller", "syscon";
+				reg = <2 0x0 0x200>;
+				reg-io-width = <2>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <2 0x0 0x0 0x200>;
+
+				led@0,0 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x01>;
+					label = "fsg:blue:wlan";
+					linux,default-trigger = "wlan";
+					default-state = "on";
+				};
+				led@0,1 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x02>;
+					label = "fsg:blue:wan";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,2 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x04>;
+					label = "fsg:blue:sata";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,3 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x04>;
+					label = "fsg:blue:usb";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,4 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x08>;
+					label = "fsg:blue:sync";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,5 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x10>;
+					label = "fsg:blue:ring";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Written based on the FSG-3 PCI boardfile.
+			 * We have slots 12, 13 & 14 (IDSEL) with one IRQ each.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 12 */
+			<0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */
+			<0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */
+			<0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */
+			<0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */
+			/* IDSEL 13 */
+			<0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
+			<0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
+			<0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
+			<0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
+			/* IDSEL 14 */
+			<0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
+			<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
+			<0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
+			<0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy4: ethernet-phy@4 {
+					reg = <4>;
+				};
+
+				phy5: ethernet-phy@5 {
+					reg = <5>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy4>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts
new file mode 100644
index 000000000000..4d70f6afd13a
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Gateway 7001 AP based on IXP422
+ * Derived from boardfiles written by Imre Kaloz
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Gateway 7001 AP";
+	compatible = "gateway,7001", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	aliases {
+		/* second UART is the primary console */
+		serial0 = &uart1;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of flash
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x7e0000 */
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from Gateway 7001 PCI boardfile (gateway7001-pci.c)
+			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+			 * each handling all IRQs.
+			 */
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 11 */
+			<0x0800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 11 */
+			<0x0800 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 11 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 10 */
+			<0x1000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 10 */
+			<0x1000 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 10 */
+		};
+
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy2>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts
new file mode 100644
index 000000000000..97e3f25bb210
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Gateworks Avila GW2348 board.
+ * This machine is based on IXP425.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Gateworks Avila GW2348";
+	compatible = "gateworks,gw2348", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-user {
+			label = "gw2348:green:user";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hwmon@28 {
+			compatible = "adi,ad7418";
+			reg = <0x28>;
+		};
+		rtc: ds1672@68 {
+			compatible = "dallas,ds1672";
+			reg = <0x68>;
+		};
+		eeprom@51 {
+			compatible = "atmel,24c08";
+			reg = <0x51>;
+			pagesize = <16>;
+			size = <1024>;
+			read-only;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+			ide@1,0 {
+				compatible = "intel,ixp4xx-compact-flash";
+				/*
+				 * Set up expansion bus config to a really slow timing.
+				 * The CF driver will dynamically reconfigure these timings
+				 * depending on selected PIO mode (0-4).
+				 */
+				intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase
+				intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase
+				intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
+				intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
+				intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
+				intel,ixp4xx-eb-byte-access-on-halfword = <1>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+				/* First register set is CMD second is CTL (notice it uses CS2) */
+				reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+			};
+			/*
+			 * FIXME: Latch LEDs or extra UARTs at CS4
+			 */
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from Avila PCI boardfile.
+			 *
+			 * We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
+			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
+			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
+			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
+			<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
+			/* IDSEL 4 */
+			<0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
+			<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
+			<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
+			<0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts
new file mode 100644
index 000000000000..9ec0169bacf8
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Goramo MultiLink Router
+ * There are two variants:
+ * - MultiLink Basic (a box)
+ * - MultiLink Max (19" rack mount)
+ * This device tree supports MultiLink Basic.
+ * This machine is based on IXP425.
+ * This is one of the few devices supporting the IXP4xx High-Speed Serial
+ * (HSS) link for a V.35 WAN interface.
+ * The hardware originates in Poland.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Goramo MultiLink Router";
+	compatible = "goramo,multilink-router", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/*
+		 * 64 MB of RAM according to the manual. The MultiLink
+		 * Max has 128 MB.
+		 */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	/*
+	 * 74HC4094 which is used as a rudimentary GPIO expander
+	 * FIXME:
+	 * - Create device tree bindings for this as GPIO expander
+	 * - Write a pure DT GPIO driver using these bindings
+	 * - Support cascading in the style of gpio-74x164.c (cannot be reused, very different)
+	 */
+	gpio_74: gpio-74hc4094 {
+		compatible = "nxp,74hc4094";
+		cp-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+		d-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+		str-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+		/* oe-gpios is optional */
+		gpio-controller;
+		#gpio-cells = <2>;
+		/* We are not cascaded */
+		registers-number = <1>;
+		gpio-line-names = "CONTROL_HSS0_CLK_INT", "CONTROL_HSS1_CLK_INT", "CONTROL_HSS0_DTR_N",
+				"CONTROL_HSS1_DTR_N", "CONTROL_EXT", "CONTROL_AUTO_RESET",
+				"CONTROL_PCI_RESET_N", "CONTROL_EEPROM_WC_N";
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * The device has 4 slots (IDSEL) with one dedicated IRQ per slot.
+			 * The slots have Ethernet, Ethernet, NEC and MPCI.
+			 * The IDSELs are 11, 12, 13, 14.
+			 */
+			interrupt-map =
+			/* IDSEL 11 - Ethernet A */
+			<0x5800 0 0 1 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 11 is irq 4 */
+			<0x5800 0 0 2 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 11 is irq 4 */
+			<0x5800 0 0 3 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 11 is irq 4 */
+			<0x5800 0 0 4 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 11 is irq 4 */
+			/* IDSEL 12 - Ethernet B */
+			<0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */
+			<0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */
+			<0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */
+			<0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */
+			/* IDSEL 13 - MPCI */
+			<0x6800 0 0 1 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 12 */
+			<0x6800 0 0 2 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 12 */
+			<0x6800 0 0 3 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 12 */
+			<0x6800 0 0 4 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 12 */
+			/* IDSEL 14 - NEC */
+			<0x7000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 3 */
+			<0x7000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 3 */
+			<0x7000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 3 */
+			<0x7000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 3 */
+		};
+
+		/* HSS links */
+		npe@c8006000 {
+			hss@0 {
+				status = "okay";
+				intel,queue-chl-rxtrig = <&qmgr 12>;
+				intel,queue-chl-txready = <&qmgr 34>;
+				intel,queue-pkt-rx = <&qmgr 13>;
+				intel,queue-pkt-tx = <&qmgr 14>, <&qmgr 15>, <&qmgr 16>, <&qmgr 17>;
+				intel,queue-pkt-rxfree = <&qmgr 18>, <&qmgr 19>, <&qmgr 20>, <&qmgr 21>;
+				intel,queue-pkt-txdone = <&qmgr 22>;
+				/* The Goramo GPIO-based clock etc control */
+				cts-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+				rts-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+				dcd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+				dtr-gpios = <&gpio_74 2 GPIO_ACTIVE_LOW>;
+				clk-internal-gpios = <&gpio_74 0 GPIO_ACTIVE_HIGH>;
+			};
+			hss@1 {
+				status = "okay";
+				intel,queue-chl-rxtrig = <&qmgr 10>;
+				intel,queue-chl-txready = <&qmgr 35>;
+				intel,queue-pkt-rx = <&qmgr 0>;
+				intel,queue-pkt-tx = <&qmgr 5>, <&qmgr 6>, <&qmgr 7>, <&qmgr 8>;
+				intel,queue-pkt-rxfree = <&qmgr 1>, <&qmgr 2>, <&qmgr 3>, <&qmgr 4>;
+				intel,queue-pkt-txdone = <&qmgr 9>;
+				/* The Goramo GPIO-based clock etc control */
+				cts-gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+				rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+				dcd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+				dtr-gpios = <&gpio_74 3 GPIO_ACTIVE_LOW>;
+				clk-internal-gpios = <&gpio_74 1 GPIO_ACTIVE_HIGH>;
+			};
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 32>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 33>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts
new file mode 100644
index 000000000000..26f02dad6a54
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Iomega NAS 100D
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Iomega NAS 100D";
+	compatible = "iom,nas-100d", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 64 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-wlan {
+			label = "nas100d:red:wlan";
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			/* We don't have WLAN trigger in the kernel (yet) */
+			linux,default-trigger = "netdev";
+		};
+		led-disk {
+			label = "nas100d:red:disk";
+			gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "disk-activity";
+		};
+		led-power {
+			label = "nas100d:red:power";
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-power {
+			wakeup-source;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		};
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		timeout-ms = <5000>;
+	};
+
+	soc {
+		bus@c4000000 {
+			/* The first 16MB region at CS0 on the expansion bus */
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 0x20000 byte blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x7e0000 */
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from NAS 100D PCI boardfile (nas100d-pci.c)
+			 * We have slots (IDSEL) 1, 2 and 3 and pins 1, 2 and 3.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 7  IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 3 is irq 7 */
+		};
+
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts
new file mode 100644
index 000000000000..194945748dc3
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Intel IXDP425 also known as IXCDP1100 Control Plane
+ * processor reference design.
+ *
+ * This platform has the codename "Richfield".
+ *
+ * This machine is based on a 533 MHz IXP425.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include "intel-ixp4xx-reference-design.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Intel IXDP425/IXCDP1100 Richfield Reference Design";
+	compatible = "intel,ixdp425", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts
new file mode 100644
index 000000000000..7011fea6205b
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Intel IXDPG425 reference design.
+ * Derived from boardfiles written by MontaVista software.
+ * Ethernet set-up from OpenWrt.
+ *
+ * The device has 4 x FXS RJ11 ports for analog phones for
+ * internet telephony. (Not supported yet.)
+ *
+ * The device has 9 status LEDs we do not support yet.
+ *
+ * This device is very similar to ADI engingeering Coyote.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Intel IXDPG425 reference design";
+	compatible = "intel,ixdpg425", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * CHECKME: the product brief says 16MB in a flash
+				 * socket.
+				 */
+				reg = <0 0x00000000 0x1000000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* CHECKME: guess this is Redboot FIS */
+					fis-index-block = <0x7f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from IXDPG425 PCI boardfile.
+			 * We have slots (IDSEL) 12, 13 and 14 with one assigned IRQ
+			 * for 12 & 13 and one for 14.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 12 */
+			<0x6000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 7 */
+			<0x6000 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 7 */
+			<0x6000 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 7 */
+			<0x6000 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 7 */
+			/* IDSEL 13 */
+			<0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
+			<0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
+			<0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
+			<0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
+			/* IDSEL 14 */
+			<0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
+			<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
+			<0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
+			<0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
+		};
+
+		/*
+		 * CHECKME: this ethernet setup seems dubious. Photos of the board shows some kind
+		 * of Realtek DSA switch on the board.
+		 */
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy4: ethernet-phy@4 {
+					reg = <4>;
+				};
+
+				phy5: ethernet-phy@5 {
+					reg = <5>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy4>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts
new file mode 100644
index 000000000000..2eec5f63d399
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Linksys NSLU2
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)";
+	compatible = "linksys,nslu2", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-status {
+			label = "nslu2:red:status";
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		led-ready {
+			label = "nslu2:green:ready";
+			gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+		led-disk-1 {
+			label = "nslu2:green:disk-1";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-disk-2 {
+			label = "nslu2:green:disk-2";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-power {
+			wakeup-source;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		};
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@6f {
+			compatible = "xicor,x1205";
+			reg = <0x6f>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+		timeout-ms = <5000>;
+	};
+
+	gpio-beeper {
+		compatible = "gpio-beeper";
+		gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+	};
+
+	soc {
+		bus@c4000000 {
+			/* The first 16MB region at CS0 on the expansion bus */
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/*
+				 * 8 MB of Flash in 0x20000 byte blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x7e0000 */
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant
+			 * We have slots (IDSEL) 1, 2 and 3.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
+			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
+			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */
+			<0x1000 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 8 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */
+			<0x1800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */
+			<0x1800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 8 */
+		};
+
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts
new file mode 100644
index 000000000000..98275a363c57
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Linksys WRV54G router
+ * Also known as Gemtek GTWX5715
+ * Based on a board file by George T. Joseph and other patches.
+ * This machine is based on IXP425.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Linksys WRV54G / Gemtek GTWX5715";
+	compatible = "linksys,wrv54g", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB memory */
+		device_type = "memory";
+		reg = <0x00000000 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	aliases {
+		/* UART2 is the primary console */
+		serial0 = &uart1;
+		serial1 = &uart0;
+	};
+
+	/* There is an unpopulated LED slot (3) connected to GPIO 8 */
+	leds {
+		compatible = "gpio-leds";
+		led-power {
+			label = "wrv54g:yellow:power";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		led-wireless {
+			label = "wrv54g:yellow:wireless";
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+		led-internet {
+			label = "wrv54g:yellow:internet";
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+		led-dmz {
+			label = "wrv54g:green:dmz";
+			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+
+	/* This set-up comes from an OpenWrt patch */
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		switch@0 {
+			compatible = "micrel,ks8995";
+			reg = <0>;
+			spi-max-frequency = <50000000>;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 8 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x00800000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					/*
+					 * Partition info from a boot log
+					 * CHECKME: not using redboot? FIS index 0x3f @7e00000?
+					 */
+					#address-cells = <1>;
+					#size-cells = <1>;
+					partition@0 {
+						label = "boot";
+						reg = <0x0 0x140000>;
+						read-only;
+					};
+					partition@140000 {
+						label = "linux";
+						reg = <0x140000 0x100000>;
+						read-only;
+					};
+					partition@240000 {
+						label = "root";
+						reg = <0x240000 0x480000>;
+						read-write;
+					};
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * We have up to 2 slots (IDSEL) with 2 swizzled IRQs.
+			 * Derived from the GTWX5715 PCI boardfile.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 0 */
+			<0x0000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 0 is irq 10 */
+			<0x0000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 0 is irq 11 */
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 1 is irq 10 */
+		};
+
+		/*
+		 * EthB - connected to the KS8995 switch ports 1-4
+		 * FIXME: the boardfile defines .phy_mask = 0x1e for this port to enable output to
+		 * all four switch ports, also using an out of tree multiphy patch.
+		 * Do we need a new binding and property for this?
+		 */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy4>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* Should be ports 1-4 on the KS8995 switch */
+				phy4: ethernet-phy@4 {
+					reg = <4>;
+				};
+
+				/* Should be port 5 on the KS8995 switch */
+				phy5: ethernet-phy@5 {
+					reg = <5>;
+				};
+			};
+		};
+
+		/* EthC - connected to KS8995 switch port 5 */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts
new file mode 100644
index 000000000000..19d56e9aec9d
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Netgear WG302v2 based on IXP422BB
+ * Derived from boardfiles written by Imre Kaloz
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear WG302 v1";
+	compatible = "netgear,wg302v1", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM according to boot arguments */
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		/* The RedBoot comes up in 9600 baud so let's keep this */
+		bootargs = "console=ttyS0,9600n8";
+		stdout-path = "uart1:9600n8";
+	};
+
+	aliases {
+		/* These are switched around */
+		serial0 = &uart1;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 64 0x20000 sized blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
+			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+			 * each handling all IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */
+			<0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */
+			<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
+			<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
+			<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
+			<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
+		};
+
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy30>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy30: ethernet-phy@30 {
+					reg = <30>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts
new file mode 100644
index 000000000000..2c89db34c8d8
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts
@@ -0,0 +1,251 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the USRobotics USR8200 firewall
+ * VPN and NAS. Based on know-how from Peter Denison.
+ *
+ * This machine is based on IXP422, the USR internal codename
+ * is "Jeeves".
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "USRobotics USR8200";
+	compatible = "usr,usr8200", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	aliases {
+		/* These are switched around */
+		serial0 = &uart1;
+		serial1 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ieee1394_led: led-1394 {
+			label = "usr8200:green:1394";
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		usb1_led: led-usb1 {
+			label = "usr8200:green:usb1";
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		usb2_led: led-usb2 {
+			label = "usr8200:green:usb2";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		wireless_led: led-wireless {
+			/*
+			 * This LED is mounted inside the case but cannot be
+			 * seen from the outside: probably USR planned at one
+			 * point for the device to have a wireless card, then
+			 * changed their mind and didn't mount it, leaving the
+			 * LED in place.
+			 */
+			label = "usr8200:green:wireless";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		pwr_led: led-pwr {
+			label = "usr8200:green:pwr";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+			rtc@2,0 {
+				/* EPSON RTC7301 DG DIL-capsule */
+				compatible = "epson,rtc7301dg";
+				/*
+				 * These timing settings were found in the boardfile patch:
+				 * IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN |
+				 *                  IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN;
+				 */
+				intel,ixp4xx-eb-t1 = <0>; // no cycles extra address phase
+				intel,ixp4xx-eb-t2 = <0>; // no cycles extra setup phase
+				intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
+				intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
+				intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle
+				intel,ixp4xx-eb-byte-access-on-halfword = <0>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+				/* 512 bytes at CS2 */
+				reg = <2 0x00000000 0x0000200>;
+				reg-io-width = <1>;
+				native-endian;
+				/* FIXME: try to check if there is an IRQ for the RTC? */
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from USR8200 boardfile from OpenWrt
+			 *
+			 * We have 3 slots (IDSEL) with partly swizzled IRQs on slot 16.
+			 * We assume the same IRQ for all pins on the remaining slots, that
+			 * is what the boardfile was doing.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 14 used for "Wireless" in the board file */
+			<0x7000 0 0 1 &gpio0 7  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */
+			/* IDSEL 15 used for VIA VT6307 IEEE 1394 Firewire */
+			<0x7800 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 8 */
+			/* IDSEL 16 used for VIA VT6202 USB 2.0 4+1 */
+			<0x8000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 16 is irq 11 */
+			<0x8000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 16 is irq 10 */
+			<0x8000 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 16 is irq 9 */
+		};
+
+		gpio@c8004000 {
+			/* Enable clock out on GPIO 15 */
+			intel,ixp4xx-gpio15-clkout;
+		};
+
+		/* EthB WAN */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy9>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * PHY 0..4 are internal to the MV88E6060 switch but appear
+				 * as independent devices.
+				 */
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+				phy3: ethernet-phy@3 {
+					reg = <3>;
+				};
+
+				/* Altima AMI101L used by the WAN port */
+				phy9: ethernet-phy@9 {
+					reg = <9>;
+				};
+
+				/* The switch uses MDIO addresses 16 thru 31 */
+				switch@16 {
+					compatible = "marvell,mv88e6060";
+					reg = <16>;
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+							label = "lan1";
+							phy-handle = <&phy0>;
+						};
+
+						port@1 {
+							reg = <1>;
+							label = "lan2";
+							phy-handle = <&phy1>;
+						};
+
+						port@2 {
+							reg = <2>;
+							label = "lan3";
+							phy-handle = <&phy2>;
+						};
+
+						port@3 {
+							reg = <3>;
+							label = "lan4";
+							phy-handle = <&phy3>;
+						};
+
+						port@5 {
+							/* Port 5 is the CPU port according to the MV88E6060 datasheet */
+							reg = <5>;
+							phy-mode = "rgmii-id";
+							ethernet = <&ethc>;
+							label = "cpu";
+							fixed-link {
+								speed = <100>;
+								full-duplex;
+							};
+						};
+					};
+				};
+			};
+		};
+
+		/* EthC LAN connected to the Marvell DSA Switch */
+		ethc: ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts
new file mode 100644
index 000000000000..c550c421b659
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+
+/ {
+	model = "Welltech EPBX100";
+	compatible = "welltech,epbx100", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 64 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/ram0 initrd=0x00800000,9M";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 16 MB of Flash
+				 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "RedBoot";
+						reg = <0x00000000 0x00080000>;
+						read-only;
+					};
+					partition@80000 {
+						label = "zImage";
+						reg = <0x00080000 0x00100000>;
+						read-only;
+					};
+					partition@180000 {
+						label = "ramdisk";
+						reg = <0x00180000 0x00300000>;
+						read-only;
+					};
+					partition@480000 {
+						label = "User";
+						reg = <0x00480000 0x00b60000>;
+						read-only;
+					};
+					partition@fe0000 {
+						label = "FIS directory";
+						reg = <0x00fe0000 0x001f000>;
+						read-only;
+					};
+					partition@fff000 {
+						label = "RedBoot config";
+						reg = <0x00fff000 0x0001000>;
+						read-only;
+					};
+				};
+			};
+		};
+
+		/* LAN port */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy5: ethernet-phy@5 {
+					reg = <5>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi
index a9622ca850cc..84cee8ec3ab8 100644
--- a/arch/arm/boot/dts/intel-ixp42x.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi
@@ -7,6 +7,15 @@
 
 / {
 	soc {
+		bus@c4000000 {
+			compatible = "intel,ixp42x-expansion-bus-controller", "syscon";
+			reg = <0xc4000000 0x30>;
+		};
+
+		pci@c0000000 {
+			compatible = "intel,ixp42x-pci";
+		};
+
 		interrupt-controller@c8003000 {
 			compatible = "intel,ixp42x-interrupt";
 		};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts
new file mode 100644
index 000000000000..1db849515f9e
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Gateworks IXP43x-based Cambria GW2358
+ */
+
+/dts-v1/;
+
+#include "intel-ixp43x.dtsi"
+
+/ {
+	model = "Gateworks Cambria GW2358";
+	compatible = "gateworks,gw2358", "intel,ixp43x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 128 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-user {
+			label = "gw2358:green:LED";
+			gpios = <&pld1 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hwmon@28 {
+			compatible = "adi,ad7418";
+			reg = <0x28>;
+		};
+		rtc: ds1672@68 {
+			compatible = "dallas,ds1672";
+			reg = <0x68>;
+		};
+		eeprom@51 {
+			compatible = "atmel,24c08";
+			reg = <0x51>;
+			pagesize = <16>;
+			size = <1024>;
+			read-only;
+		};
+		pld0: pld@56 {
+			compatible = "gateworks,pld-gpio";
+			reg = <0x56>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+		/* This PLD just handles the LED and user button */
+		pld1: pld@57 {
+			compatible = "gateworks,pld-gpio";
+			reg = <0x57>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/*
+				 * 32 MB of Flash in 0x20000 byte blocks
+				 * mapped in at CS0 and CS1
+				 */
+				reg = <0 0x00000000 0x2000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x1fe0000 */
+					fis-index-block = <0xff>;
+				};
+			};
+			ide@3,0 {
+				compatible = "intel,ixp4xx-compact-flash";
+				/*
+				 * Set up expansion bus config to a really slow timing.
+				 * The CF driver will dynamically reconfigure these timings
+				 * depending on selected PIO mode (0-4).
+				 */
+				intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase
+				intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase
+				intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
+				intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
+				intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
+				intel,ixp4xx-eb-byte-access-on-halfword = <1>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+				/* First register set is CMD second is CTL */
+				reg = <3 0xe00000 0x40000>, <3 0xe40000 0x40000>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * In the boardfile for the Cambria from OpenWRT the interrupts
+			 * are assigned one per IDSEL, so all 4 interrupts from IDSEL
+			 * 1 are connected to IRQ 11, all 4 interrupts from IDSEL 2
+			 * connected to IRQ 10 etc. I find this highly unlikely so I
+			 * have instead assumed that they are rotated (swizzled) like
+			 * this with 11, 10, 9, 8 for the 4 pins on IDSEL 1 etc.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
+			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
+			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
+			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
+			<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
+			/* IDSEL 4 */
+			<0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */
+			<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */
+			<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */
+			<0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 9 */
+			/* IDSEL 6 */
+			<0x3000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 10 */
+			<0x3000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 9 */
+			<0x3000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 8 */
+			<0x3000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 11 */
+			/* IDSEL 15 */
+			<0x7800 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */
+			<0x7800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */
+			<0x7800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */
+			<0x7800 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 9 */
+		};
+
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
+		};
+
+		ethernet@c800c000 {
+			status = "okay";
+			queue-rx = <&qmgr 2>;
+			queue-txready = <&qmgr 19>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy2>;
+			intel,npe-handle = <&npe 0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts
new file mode 100644
index 000000000000..4703a8b24765
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Intel KIXRP435 Control Plane
+ * processor reference design.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp43x.dtsi"
+#include "intel-ixp4xx-reference-design.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Intel KIXRP435 Reference Design";
+	compatible = "intel,kixrp435", "intel,ixp43x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+		};
+
+		/* CHECKME: ethernet set-up taken from Gateworks Cambria */
+		ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
+		};
+
+		ethernet@c800c000 {
+			status = "okay";
+			queue-rx = <&qmgr 2>;
+			queue-txready = <&qmgr 19>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy2>;
+			intel,npe-handle = <&npe 0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp43x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi
index 494fb2ff57a0..60bf9903e0f8 100644
--- a/arch/arm/boot/dts/intel-ixp43x.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi
@@ -8,6 +8,16 @@
 
 / {
 	soc {
+		bus@c4000000 {
+			compatible = "intel,ixp43x-expansion-bus-controller", "syscon";
+			/* Uses at least up to 0x230 */
+			reg = <0xc4000000 0x1000>;
+		};
+
+		pci@c0000000 {
+			compatible = "intel,ixp43x-pci";
+		};
+
 		interrupt-controller@c8003000 {
 			compatible = "intel,ixp43x-interrupt";
 		};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi
new file mode 100644
index 000000000000..1dd4a65cb7a6
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP45x and IXP46x series. This series has 64 interrupts and adds a
+ * few more peripherals over the 42x and 43x series so this extends the
+ * basic IXP4xx DTSI.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+	soc {
+		bus@c4000000 {
+			compatible = "intel,ixp46x-expansion-bus-controller", "syscon";
+			/* Uses at least up to 0x124 */
+			reg = <0xc4000000 0x1000>;
+		};
+
+		rng@70002100 {
+			compatible = "intel,ixp46x-rng";
+			reg = <0x70002100 4>;
+		};
+
+		interrupt-controller@c8003000 {
+			compatible = "intel,ixp43x-interrupt";
+		};
+
+		/*
+		 * This is the USB Device Mode (UDC) controller, which is used
+		 * to present the IXP4xx as a device on a USB bus.
+		 */
+		usb@c800b000 {
+			compatible = "intel,ixp4xx-udc";
+			reg = <0xc800b000 0x1000>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		i2c@c8011000 {
+			compatible = "intel,ixp4xx-i2c";
+			reg = <0xc8011000 0x18>;
+			interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		/* This is known as EthB1 */
+		ethernet@c800d000 {
+			compatible = "intel,ixp4xx-ethernet";
+			reg = <0xc800d000 0x1000>;
+			status = "disabled";
+			intel,npe = <1>;
+			/* Dummy values that depend on firmware */
+			queue-rx = <&qmgr 0>;
+			queue-txready = <&qmgr 0>;
+		};
+
+		/* This is known as EthB2 */
+		ethernet@c800e000 {
+			compatible = "intel,ixp4xx-ethernet";
+			reg = <0xc800e000 0x1000>;
+			status = "disabled";
+			intel,npe = <2>;
+			/* Dummy values that depend on firmware */
+			queue-rx = <&qmgr 0>;
+			queue-txready = <&qmgr 0>;
+		};
+
+		/* This is known as EthB3 */
+		ethernet@c800f000 {
+			compatible = "intel,ixp4xx-ethernet";
+			reg = <0xc800f000 0x1000>;
+			status = "disabled";
+			intel,npe = <3>;
+			/* Dummy values that depend on firmware */
+			queue-rx = <&qmgr 0>;
+			queue-txready = <&qmgr 0>;
+		};
+
+		ptp-timer@c8010000 {
+			compatible = "intel,ixp46x-ptp-timer";
+			reg = <0xc8010000 0x1000>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <8 IRQ_TYPE_EDGE_FALLING>, <7 IRQ_TYPE_EDGE_FALLING>;
+			interrupt-names = "master", "slave";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts
new file mode 100644
index 000000000000..a062cd1a6588
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Intel IXDP465 Control Plane processor reference
+ * design, codename "BMP".
+ */
+
+/dts-v1/;
+
+#include "intel-ixp45x-ixp46x.dtsi"
+#include "intel-ixp4xx-reference-design.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Intel IXDP465 BMP Reference Design";
+	compatible = "intel,ixdp465", "intel,ixp46x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 32 MB of Flash mapped in at CS0 and CS1 */
+				reg = <0 0x00000000 0x2000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x1fe0000 */
+					fis-index-block = <0xff>;
+				};
+			};
+		};
+		/* TODO: configure ethernet etc */
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi
new file mode 100644
index 000000000000..31c0a69771c4
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree include file for Intel reference designs for the
+ * XScale Network Processors in the IXP 4xx series. Common device
+ * set-up for IXDP425, IXCDP1100, KIXRP435 and IXDP465.
+ */
+
+/ {
+	memory@0 {
+		/*
+		 * The board supports up to 256 MB of memory. Here we put in
+		 * 64 MB and this may be modified by the boot loader.
+		 */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eeprom@50 {
+			/*
+			 * Philips PCF8582C-2T/03 512byte I2C EEPROM
+			 * should behave like an Atmel 24c04.
+			 */
+			compatible = "atmel,24c04";
+			reg = <0x50>;
+			pagesize = <16>;
+			size = <512>;
+			read-only;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			/* Flash memory defined per-variant */
+			nand-controller@3,0 {
+				/* Some designs have a NAND on CS3 enable it here if present */
+				status = "disabled";
+
+				/*
+				 * gen_nand needs to be extended and documented to get
+				 * command byte = 1 and address byte = 2 from the device
+				 * tree.
+				 */
+				compatible = "gen_nand";
+
+				/* Expansion bus set-up */
+				intel,ixp4xx-eb-t1 = <0>;
+				intel,ixp4xx-eb-t2 = <0>;
+				intel,ixp4xx-eb-t3 = <1>; // 1 cycle extra strobe phase
+				intel,ixp4xx-eb-t4 = <0>;
+				intel,ixp4xx-eb-t5 = <0>;
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
+				intel,ixp4xx-eb-byte-access-on-halfword = <0>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+
+				/* 512 bytes memory window */
+				reg = <3 0x00000000 0x200>;
+				nand-on-flash-bbt;
+				nand-ecc-mode = "soft_bch";
+				nand-ecc-step-size = <512>;
+				nand-ecc-strength = <4>;
+				nce-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* NCE */
+
+				label = "ixp400 NAND";
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					fs@0 {
+						label = "ixp400 NAND FS 0";
+						reg = <0x0 0x800000>;
+					};
+					fs@800000 {
+						label = "ixp400 NAND FS 1";
+						reg = <0x800000 0x0>;
+					};
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from IXDP425 PCI boardfile.
+			 * PCI slots on the BIXMB425BD base card.
+			 * We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
+			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
+			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
+			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
+			<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
+			/* IDSEL 4 */
+			<0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
+			<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
+			<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
+			<0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi
new file mode 100644
index 000000000000..51a716c59669
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 4xx series.
+ */
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+		interrupt-parent = <&intcon>;
+
+		/*
+		 * The IXP4xx expansion bus is a set of up to 7 each up to 16MB
+		 * windows in the 256MB space from 0x50000000 to 0x5fffffff.
+		 */
+		bus@c4000000 {
+			/* compatible and reg filled in by per-soc device tree */
+			native-endian;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0 0x0 0x50000000 0x01000000>,
+				 <1 0x0 0x51000000 0x01000000>,
+				 <2 0x0 0x52000000 0x01000000>,
+				 <3 0x0 0x53000000 0x01000000>,
+				 <4 0x0 0x54000000 0x01000000>,
+				 <5 0x0 0x55000000 0x01000000>,
+				 <6 0x0 0x56000000 0x01000000>,
+				 <7 0x0 0x57000000 0x01000000>;
+			dma-ranges = <0 0x0 0x50000000 0x01000000>,
+				 <1 0x0 0x51000000 0x01000000>,
+				 <2 0x0 0x52000000 0x01000000>,
+				 <3 0x0 0x53000000 0x01000000>,
+				 <4 0x0 0x54000000 0x01000000>,
+				 <5 0x0 0x55000000 0x01000000>,
+				 <6 0x0 0x56000000 0x01000000>,
+				 <7 0x0 0x57000000 0x01000000>;
+		};
+
+		qmgr: queue-manager@60000000 {
+			compatible = "intel,ixp4xx-ahb-queue-manager";
+			reg = <0x60000000 0x4000>;
+			interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pci@c0000000 {
+			/* compatible filled in by per-soc device tree */
+			reg = <0xc0000000 0x1000>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>,
+				     <9 IRQ_TYPE_LEVEL_HIGH>,
+				     <10 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			bus-range = <0x00 0xff>;
+			status = "disabled";
+
+			ranges =
+			/*
+			 * 64MB 32bit non-prefetchable memory 0x48000000-0x4bffffff
+			 * done in 4 chunks of 16MB each.
+			 */
+			<0x02000000 0 0x48000000 0x48000000 0 0x04000000>,
+			/* 64KB I/O space at 0x4c000000 */
+			<0x01000000 0 0x00000000 0x4c000000 0 0x00010000>;
+
+			/*
+			 * This needs to map to the start of physical memory so
+			 * PCI devices can see all (hopefully) memory. This is done
+			 * using 4 1:1 16MB windows, so the RAM should not be more than
+			 * 64 MB for this to work. If your memory is anywhere else
+			 * than at 0x0 you need to alter this.
+			 */
+			dma-ranges =
+			<0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+			/* Each unique DTS using PCI must specify the swizzling */
+		};
+
+		uart0: serial@c8000000 {
+			compatible = "intel,xscale-uart";
+			reg = <0xc8000000 0x1000>;
+			/*
+			 * The reg-offset and reg-shift is a side effect
+			 * of running the platform in big endian mode.
+			 */
+			reg-offset = <3>;
+			reg-shift = <2>;
+			interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <14745600>;
+			no-loopback-test;
+		};
+
+		uart1: serial@c8001000 {
+			compatible = "intel,xscale-uart";
+			reg = <0xc8001000 0x1000>;
+			/*
+			 * The reg-offset and reg-shift is a side effect
+			 * of running the platform in big endian mode.
+			 */
+			reg-offset = <3>;
+			reg-shift = <2>;
+			interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <14745600>;
+			no-loopback-test;
+		};
+
+		gpio0: gpio@c8004000 {
+			compatible = "intel,ixp4xx-gpio";
+			reg = <0xc8004000 0x1000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		intcon: interrupt-controller@c8003000 {
+			/*
+			 * Note: no compatible string. The subvariant of the
+			 * chip needs to define what version it is. The
+			 * location of the interrupt controller is fixed in
+			 * memory across all variants.
+			 */
+			reg = <0xc8003000 0x100>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		timer@c8005000 {
+			compatible = "intel,ixp4xx-timer";
+			reg = <0xc8005000 0x100>;
+			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		npe: npe@c8006000 {
+			compatible = "intel,ixp4xx-network-processing-engine";
+			reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* NPE-A contains two high-speed serial links */
+			hss@0 {
+				compatible = "intel,ixp4xx-hss";
+				reg = <0>;
+				intel,npe-handle = <&npe 0>;
+				status = "disabled";
+			};
+
+			hss@1 {
+				compatible = "intel,ixp4xx-hss";
+				reg = <1>;
+				intel,npe-handle = <&npe 0>;
+				status = "disabled";
+			};
+
+			/* NPE-C contains a crypto accelerator */
+			crypto {
+				compatible = "intel,ixp4xx-crypto";
+				intel,npe-handle = <&npe 2>;
+				queue-rx = <&qmgr 30>;
+				queue-txready = <&qmgr 29>;
+			};
+		};
+
+		/* This is known as EthB */
+		ethernet@c8009000 {
+			compatible = "intel,ixp4xx-ethernet";
+			reg = <0xc8009000 0x1000>;
+			status = "disabled";
+			/* Dummy values that depend on firmware */
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			intel,npe-handle = <&npe 1>;
+		};
+
+		/* This is known as EthC */
+		ethernet@c800a000 {
+			compatible = "intel,ixp4xx-ethernet";
+			reg = <0xc800a000 0x1000>;
+			status = "disabled";
+			/* Dummy values that depend on firmware */
+			queue-rx = <&qmgr 0>;
+			queue-txready = <&qmgr 0>;
+			intel,npe-handle = <&npe 2>;
+		};
+
+		/* This is known as EthA */
+		ethernet@c800c000 {
+			compatible = "intel,ixp4xx-ethernet";
+			reg = <0xc800c000 0x1000>;
+			status = "disabled";
+			intel,npe = <0>;
+			/* Dummy values that depend on firmware */
+			queue-rx = <&qmgr 0>;
+			queue-txready = <&qmgr 0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/pxa/Makefile b/arch/arm/boot/dts/intel/pxa/Makefile
new file mode 100644
index 000000000000..24d5240f08e7
--- /dev/null
+++ b/arch/arm/boot/dts/intel/pxa/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_PXA) += \
+	pxa300-raumfeld-connector.dtb \
+	pxa300-raumfeld-controller.dtb \
+	pxa300-raumfeld-speaker-l.dtb \
+	pxa300-raumfeld-speaker-m.dtb \
+	pxa300-raumfeld-speaker-one.dtb \
+	pxa300-raumfeld-speaker-s.dtb
diff --git a/arch/arm/boot/dts/pxa25x.dtsi b/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi
index a248bf038033..5f8300e356ad 100644
--- a/arch/arm/boot/dts/pxa25x.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi
@@ -38,9 +38,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <16>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <16>;
+			dma-channels = <16>;
 			#dma-requests = <40>;
+			dma-requests = <40>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/pxa27x.dtsi b/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi
index ccbecad9c5c7..a2cbfb3be609 100644
--- a/arch/arm/boot/dts/pxa27x.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi
@@ -12,9 +12,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <32>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <32>;
+			dma-channels = <32>;
 			#dma-requests = <75>;
+			dma-requests = <75>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/pxa2xx.dtsi b/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi
index 84154c43fe65..84154c43fe65 100644
--- a/arch/arm/boot/dts/pxa2xx.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi
index 8a6721d436bd..147c99191dc2 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi
@@ -189,31 +189,31 @@
 
 		regulators {
 			regulator-v3 {
-				regulator-compatible= "V3(DCDC)";
+				regulator-compatible = "V3(DCDC)";
 				regulator-min-microvolt = <725000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			regulator-v4 {
-				regulator-compatible= "V4(DCDC)";
+				regulator-compatible = "V4(DCDC)";
 				regulator-min-microvolt = <725000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			regulator-v5 {
-				regulator-compatible= "V5(LDO)";
+				regulator-compatible = "V5(LDO)";
 				regulator-min-microvolt = <1700000>;
 				regulator-max-microvolt = <2000000>;
 			};
 
 			reg_vcc_sdio: regulator-v6 {
-				regulator-compatible= "V6(LDO)";
+				regulator-compatible = "V6(LDO)";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			regulator-v7 {
-				regulator-compatible= "V7(LDO)";
+				regulator-compatible = "V7(LDO)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-connector.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts
index 3e9445419e39..3e9445419e39 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-connector.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-controller.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts
index 12b15945ac6d..12b15945ac6d 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-controller.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-l.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts
index 5a0f7f17856f..5a0f7f17856f 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-l.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-m.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts
index fa10d896282c..fa10d896282c 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-m.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-one.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts
index a70560a8ea92..a70560a8ea92 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-one.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-s.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts
index 36e20cbf8704..36e20cbf8704 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-s.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-tuneable-clock.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi
index 561483b93989..561483b93989 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-tuneable-clock.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi
diff --git a/arch/arm/boot/dts/pxa3xx.dtsi b/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi
index c237a0e4b12a..f9c216f91865 100644
--- a/arch/arm/boot/dts/pxa3xx.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi
@@ -122,9 +122,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <32>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <32>;
+			dma-channels = <32>;
 			#dma-requests = <100>;
+			dma-requests = <100>;
 			status = "okay";
 		};
 
@@ -170,7 +173,7 @@
 			clocks = <&clks CLK_GPIO>;
 			gpio-ranges = <&pinctrl 0 0 128>;
 			interrupt-names = "gpio0", "gpio1", "gpio_mux";
-			interrupts = <8 9 10>;
+			interrupts = <8>, <9>, <10>;
 			gpio-controller;
 			#gpio-cells = <0x2>;
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/intel/socfpga/Makefile b/arch/arm/boot/dts/intel/socfpga/Makefile
new file mode 100644
index 000000000000..c467828aeb4b
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/Makefile
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
+	socfpga_arria5_socdk.dtb \
+	socfpga_arria10_chameleonv3.dtb \
+	socfpga_arria10_mercury_pe1.dtb \
+	socfpga_arria10_socdk_nand.dtb \
+	socfpga_arria10_socdk_qspi.dtb \
+	socfpga_arria10_socdk_sdmmc.dtb \
+	socfpga_cyclone5_chameleon96.dtb \
+	socfpga_cyclone5_mcvevk.dtb \
+	socfpga_cyclone5_socdk.dtb \
+	socfpga_cyclone5_de0_nano_soc.dtb \
+	socfpga_cyclone5_sockit.dtb \
+	socfpga_cyclone5_socrates.dtb \
+	socfpga_cyclone5_sodia.dtb \
+	socfpga_cyclone5_vining_fpga.dtb \
+	socfpga_vt.dtb
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi
index 4f3993cc0227..35be14150f41 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi
@@ -46,7 +46,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@fffed000 {
+	intc: interrupt-controller@fffed000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -80,8 +80,6 @@
 					     <0 110 4>,
 					     <0 111 4>;
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				clocks = <&l4_main_clk>;
 				clock-names = "apb_pclk";
 				resets = <&rst DMA_RESET>;
@@ -455,7 +453,6 @@
 						compatible = "altr,socfpga-gate-clk";
 						clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
 						clk-gate = <0xa0 8>;
-						clk-phase = <0 135>;
 					};
 
 					sdmmc_clk_divided: sdmmc_clk_divided {
@@ -531,6 +528,7 @@
 			reg = <0xff400000 0x100000>;
 			resets = <&rst LWHPS2FPGA_RESET>;
 			clocks = <&l4_main_clk>;
+			status = "disabled";
 		};
 
 		fpga_bridge1: fpga_bridge@ff500000 {
@@ -538,6 +536,21 @@
 			reg = <0xff500000 0x10000>;
 			resets = <&rst HPS2FPGA_RESET>;
 			clocks = <&l4_main_clk>;
+			status = "disabled";
+		};
+
+		fpga_bridge2: fpga-bridge@ff600000 {
+			compatible = "altr,socfpga-fpga2hps-bridge";
+			reg = <0xff600000 0x100000>;
+			resets = <&rst FPGA2HPS_RESET>;
+			clocks = <&l4_main_clk>;
+			status = "disabled";
+		};
+
+		fpga_bridge3: fpga-bridge@ffc25080 {
+			compatible = "altr,socfpga-fpga2sdram-bridge";
+			reg = <0xffc25080 0x4>;
+			status = "disabled";
 		};
 
 		fpgamgr0: fpgamgr@ff706000 {
@@ -547,6 +560,12 @@
 			interrupts = <0 175 4>;
 		};
 
+		socfpga_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <0xf>;
+			snps,rd_osr_lmt = <0xf>;
+			snps,blen = <0 0 0 0 16 0 0>;
+		};
+
 		gmac0: ethernet@ff700000 {
 			compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac";
 			altr,sysmgr-syscon = <&sysmgr 0x60 0>;
@@ -562,6 +581,7 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <4096>;
+			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
 
@@ -580,6 +600,7 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <4096>;
+			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
 
@@ -710,7 +731,7 @@
 			};
 		};
 
-		L2: l2-cache@fffef000 {
+		L2: cache-controller@fffef000 {
 			compatible = "arm,pl310-cache";
 			reg = <0xfffef000 0x1000>;
 			interrupts = <0 38 0x04>;
@@ -728,12 +749,12 @@
 			arm,prefetch-offset = <7>;
 		};
 
-		l3regs@0xff800000 {
+		l3regs@ff800000 {
 			compatible = "altr,l3regs", "syscon";
 			reg = <0xff800000 0x1000>;
 		};
 
-		mmc: dwmmc0@ff704000 {
+		mmc: mmc@ff704000 {
 			compatible = "altr,socfpga-dw-mshc";
 			reg = <0xff704000 0x1000>;
 			interrupts = <0 139 4>;
@@ -743,10 +764,11 @@
 			clocks = <&l4_mp_clk>, <&sdmmc_clk_divided>;
 			clock-names = "biu", "ciu";
 			resets = <&rst SDMMC_RESET>;
+			altr,sysmgr-syscon = <&sysmgr 0x108 3>;
 			status = "disabled";
 		};
 
-		nand0: nand@ff900000 {
+		nand0: nand-controller@ff900000 {
 			#address-cells = <0x1>;
 			#size-cells = <0x0>;
 			compatible = "altr,socfpga-denali-nand";
@@ -766,7 +788,7 @@
 		};
 
 		qspi: spi@ff705000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff705000 0x1000>,
@@ -813,6 +835,7 @@
 			num-cs = <4>;
 			clocks = <&spi_m_clk>;
 			resets = <&rst SPIM0_RESET>;
+			reset-names = "spi";
 			status = "disabled";
 		};
 
@@ -825,6 +848,7 @@
 			num-cs = <4>;
 			clocks = <&spi_m_clk>;
 			resets = <&rst SPIM1_RESET>;
+			reset-names = "spi";
 			status = "disabled";
 		};
 
@@ -881,7 +905,7 @@
 			reset-names = "timer";
 		};
 
-		uart0: serial0@ffc02000 {
+		uart0: serial@ffc02000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc02000 0x1000>;
 			interrupts = <0 162 4>;
@@ -894,7 +918,7 @@
 			resets = <&rst UART0_RESET>;
 		};
 
-		uart1: serial1@ffc03000 {
+		uart1: serial@ffc03000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc03000 0x1000>;
 			interrupts = <0 163 4>;
diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi
index 2a86e72d9791..6b6e77596ffa 100644
--- a/arch/arm/boot/dts/socfpga_arria10.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi
@@ -15,13 +15,13 @@
 		#size-cells = <0>;
 		enable-method = "altr,socfpga-a10-smp";
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0>;
 			next-level-cache = <&L2>;
 		};
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <1>;
@@ -29,7 +29,16 @@
 		};
 	};
 
-	intc: intc@ffffd000 {
+	pmu: pmu@ff111000 {
+		compatible = "arm,cortex-a9-pmu";
+		interrupt-parent = <&intc>;
+		interrupts = <0 124 4>, <0 125 4>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+		reg = <0xff111000 0x1000>,
+		      <0xff113000 0x1000>;
+	};
+
+	intc: interrupt-controller@ffffd000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -64,8 +73,6 @@
 					     <0 90 IRQ_TYPE_LEVEL_HIGH>,
 					     <0 91 IRQ_TYPE_LEVEL_HIGH>;
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				clocks = <&l4_main_clk>;
 				clock-names = "apb_pclk";
 				resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>;
@@ -358,7 +365,6 @@
 						compatible = "altr,socfpga-a10-gate-clk";
 						clocks = <&sdmmc_free_clk>;
 						clk-gate = <0xC8 5>;
-						clk-phase = <0 135>;
 					};
 
 					qspi_clk: qspi_clk {
@@ -431,10 +437,10 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <16384>;
-			clocks = <&l4_mp_clk>;
-			clock-names = "stmmaceth";
+			clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>;
+			clock-names = "stmmaceth", "ptp_ref";
 			resets = <&rst EMAC0_RESET>, <&rst EMAC0_OCP_RESET>;
-			reset-names = "stmmaceth", "stmmaceth-ocp";
+			reset-names = "stmmaceth", "ahb";
 			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
@@ -451,10 +457,10 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <16384>;
-			clocks = <&l4_mp_clk>;
-			clock-names = "stmmaceth";
+			clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>;
+			clock-names = "stmmaceth", "ptp_ref";
 			resets = <&rst EMAC1_RESET>, <&rst EMAC1_OCP_RESET>;
-			reset-names = "stmmaceth", "stmmaceth-ocp";
+			reset-names = "stmmaceth", "ahb";
 			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
@@ -471,10 +477,10 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <16384>;
-			clocks = <&l4_mp_clk>;
-			clock-names = "stmmaceth";
+			clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>;
+			clock-names = "stmmaceth", "ptp_ref";
 			resets = <&rst EMAC2_RESET>, <&rst EMAC2_OCP_RESET>;
-			reset-names = "stmmaceth", "stmmaceth-ocp";
+			reset-names = "stmmaceth", "ahb";
 			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
@@ -613,6 +619,7 @@
 			/*32bit_access;*/
 			clocks = <&spi_m_clk>;
 			resets = <&rst SPIM0_RESET>;
+			reset-names = "spi";
 			status = "disabled";
 		};
 
@@ -628,6 +635,7 @@
 			rx-dma-channel = <&pdma 17>;
 			clocks = <&spi_m_clk>;
 			resets = <&rst SPIM1_RESET>;
+			reset-names = "spi";
 			status = "disabled";
 		};
 
@@ -636,7 +644,7 @@
 			reg = <0xffcfb100 0x80>;
 		};
 
-		L2: l2-cache@fffff000 {
+		L2: cache-controller@fffff000 {
 			compatible = "arm,pl310-cache";
 			reg = <0xfffff000 0x1000>;
 			interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
@@ -647,7 +655,7 @@
 			arm,shared-override;
 		};
 
-		mmc: dwmmc0@ff808000 {
+		mmc: mmc@ff808000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "altr,socfpga-dw-mshc";
@@ -657,10 +665,11 @@
 			clocks = <&l4_mp_clk>, <&sdmmc_clk>;
 			clock-names = "biu", "ciu";
 			resets = <&rst SDMMC_RESET>;
+			altr,sysmgr-syscon = <&sysmgr 0x28 4>;
 			status = "disabled";
 		};
 
-		nand: nand@ffb90000 {
+		nand: nand-controller@ffb90000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "altr,socfpga-denali-nand";
@@ -727,6 +736,16 @@
 					     <37 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
+			sdmmca-ecc@ff8c2c00 {
+				compatible = "altr,socfpga-sdmmc-ecc";
+				reg = <0xff8c2c00 0x400>;
+				altr,ecc-parent = <&mmc>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+					     <47 IRQ_TYPE_LEVEL_HIGH>,
+					     <16 IRQ_TYPE_LEVEL_HIGH>,
+					     <48 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			dma-ecc@ff8c8000 {
 				compatible = "altr,socfpga-dma-ecc";
 				reg = <0xff8c8000 0x400>;
@@ -745,7 +764,7 @@
 		};
 
 		qspi: spi@ff809000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff809000 0x100>,
@@ -819,14 +838,14 @@
 		timer3: timer3@ffd00100 {
 			compatible = "snps,dw-apb-timer";
 			interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>;
-			reg = <0xffd01000 0x100>;
+			reg = <0xffd00100 0x100>;
 			clocks = <&l4_sys_free_clk>;
 			clock-names = "timer";
 			resets = <&rst L4SYSTIMER1_RESET>;
 			reset-names = "timer";
 		};
 
-		uart0: serial0@ffc02000 {
+		uart0: serial@ffc02000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc02000 0x100>;
 			interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -837,7 +856,7 @@
 			status = "disabled";
 		};
 
-		uart1: serial1@ffc02100 {
+		uart1: serial@ffc02100 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc02100 0x100>;
 			interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts
new file mode 100644
index 000000000000..422d00cd4c74
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2022 Google LLC
+ */
+/dts-v1/;
+#include "socfpga_arria10_mercury_aa1.dtsi"
+
+/ {
+	model = "Google Chameleon V3";
+	compatible = "google,chameleon-v3", "enclustra,mercury-aa1",
+		     "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		serial0 = &uart0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	ssm2603: audio-codec@1a {
+		compatible = "adi,ssm2603";
+		reg = <0x1a>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	u80: gpio@21 {
+		compatible = "nxp,pca9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SOM_AUD_MUTE",
+			"DP1_OUT_CEC_EN",
+			"DP2_OUT_CEC_EN",
+			"DP1_SOM_PS8469_CAD",
+			"DPD_SOM_PS8469_CAD",
+			"DP_OUT_PWR_EN",
+			"STM32_RST_L",
+			"STM32_BOOT0",
+
+			"FPGA_PROT",
+			"STM32_FPGA_COMM0",
+			"TP119",
+			"TP120",
+			"TP121",
+			"TP122",
+			"TP123",
+			"TP124";
+	};
+};
+
+&mmc {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi
new file mode 100644
index 000000000000..41f865c8c098
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2022 Google LLC
+ */
+
+#include "socfpga_arria10.dtsi"
+
+/ {
+
+	model = "Enclustra Mercury AA1";
+	compatible = "enclustra,mercury-aa1", "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial1 = &uart1;
+	};
+
+	memory@0 {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>; /* probe for phy addr */
+
+	max-frame-size = <3800>;
+
+	phy-handle = <&phy3>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy3: ethernet-phy@3 {
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <1860>; /* 960ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	atsha204a: crypto@64 {
+		compatible = "atmel,atsha204a";
+		reg = <0x64>;
+	};
+
+	isl12022: isl12022@6f {
+		compatible = "isil,isl12022";
+		reg = <0x6f>;
+	};
+};
+
+/* Following mappings are taken from arria10 socdk dts */
+&mmc {
+	cap-sd-highspeed;
+	broken-cd;
+	bus-width = <4>;
+	clk-phase-sd-hs = <0>, <135>;
+};
+
+&osc1 {
+	clock-frequency = <33330000>;
+};
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts
new file mode 100644
index 000000000000..cf533f76a9fd
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2023 Steffen Trumtrar <kernel@pengutronix.de>
+ */
+/dts-v1/;
+#include "socfpga_arria10_mercury_aa1.dtsi"
+
+/ {
+	model = "Enclustra Mercury+ PE1";
+	compatible = "enclustra,mercury-pe1", "enclustra,mercury-aa1",
+		     "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&mmc {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi
index 0efbeccc5cd2..ec7365444a3b 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi
@@ -6,7 +6,7 @@
 
 / {
 	model = "Altera SOCFPGA Arria 10";
-	compatible = "altr,socfpga-arria10", "altr,socfpga";
+	compatible = "altr,socfpga-arria10-socdk", "altr,socfpga-arria10", "altr,socfpga";
 
 	aliases {
 		ethernet0 = &gmac0;
@@ -162,6 +162,11 @@
 		compatible = "ltc2977";
 		reg = <0x5c>;
 	};
+
+	temp@4c {
+		compatible = "maxim,max1619";
+		reg = <0x4c>;
+	};
 };
 
 &uart1 {
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_nand.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts
index 9bd9e04c7361..a662df319a84 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_nand.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts
@@ -16,11 +16,11 @@
 
 		partition@0 {
 			label = "Boot and fpga data";
-			reg = <0x0 0x1C00000>;
+			reg = <0x0 0x02500000>;
 		};
 		partition@1c00000 {
 			label = "Root Filesystem - JFFS2";
-			reg = <0x1C00000 0x6400000>;
+			reg = <0x02500000 0x05500000>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts
index 2b645642b935..0434f1c7b665 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts
@@ -9,16 +9,14 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q00@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00aa";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <3>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_sdmmc.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts
index 64dc0799f3d7..d3969367f4b5 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_sdmmc.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts
@@ -12,6 +12,7 @@
 	cap-mmc-highspeed;
 	broken-cd;
 	bus-width = <4>;
+	clk-phase-sd-hs = <0>, <135>;
 };
 
 &eccmgr {
diff --git a/arch/arm/boot/dts/socfpga_arria5.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi
index 22dbf07afcff..40fecde65c54 100644
--- a/arch/arm/boot/dts/socfpga_arria5.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi
@@ -18,11 +18,12 @@
 			};
 		};
 
-		mmc0: dwmmc0@ff704000 {
+		mmc0: mmc@ff704000 {
 			broken-cd;
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			cap-sd-highspeed;
+			clk-phase-sd-hs = <0>, <135>;
 		};
 
 		sysmgr@ffd08000 {
diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts
index 90e676e7019f..7342f5942b0d 100644
--- a/arch/arm/boot/dts/socfpga_arria5_socdk.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts
@@ -7,7 +7,7 @@
 
 / {
 	model = "Altera SOCFPGA Arria V SoC Development Kit";
-	compatible = "altr,socfpga-arria5", "altr,socfpga";
+	compatible = "altr,socfpga-arria5-socdk", "altr,socfpga-arria5", "altr,socfpga";
 
 	chosen {
 		bootargs = "earlyprintk";
@@ -29,28 +29,28 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led-hps0 {
 			label = "hps_led0";
 			gpios = <&porta 0 1>;
 		};
 
-		hps1 {
+		led-hps1 {
 			label = "hps_led1";
 			gpios = <&portb 11 1>;
 		};
 
-		hps2 {
+		led-hps2 {
 			label = "hps_led2";
 			gpios = <&porta 17 1>;
 		};
 
-		hps3 {
+		led-hps3 {
 			label = "hps_led3";
 			gpios = <&porta 18 1>;
 		};
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -119,13 +119,11 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi
index 319a71e41ea4..305fe207b237 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi
@@ -18,11 +18,12 @@
 			};
 		};
 
-		mmc0: dwmmc0@ff704000 {
+		mmc0: mmc@ff704000 {
 			broken-cd;
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			cap-sd-highspeed;
+			clk-phase-sd-hs = <0>, <135>;
 		};
 
 		sysmgr@ffd08000 {
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts
index f6561766d83f..76262f1e5e03 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts
@@ -24,7 +24,7 @@
 		reg = <0x0 0x20000000>; /* 512MB */
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts
index 67076e1b1c7f..bedf577cb056 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts
@@ -24,7 +24,7 @@
 		ethernet0 = &gmac1;
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -33,7 +33,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led-hps0 {
 			label = "hps_led0";
 			gpios = <&portb 24 0>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi
index bd92806ffc12..3b9daddf91cd 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi
@@ -18,5 +18,6 @@
 
 &mmc0 {	/* On-SoM eMMC */
 	bus-width = <8>;
+	clk-phase-sd-hs = <0>, <135>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts
index ceaec29770c6..ceaec29770c6 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts
index 6f138b2b2616..d37a982e8571 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts
@@ -29,28 +29,28 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led-hps0 {
 			label = "hps_led0";
 			gpios = <&portb 15 1>;
 		};
 
-		hps1 {
+		led-hps1 {
 			label = "hps_led1";
 			gpios = <&portb 14 1>;
 		};
 
-		hps2 {
+		led-hps2 {
 			label = "hps_led2";
 			gpios = <&portb 13 1>;
 		};
 
-		hps3 {
+		led-hps3 {
 			label = "hps_led3";
 			gpios = <&portb 12 1>;
 		};
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -121,16 +121,14 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q00@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;	/* chip select */
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts
index c155ff02eb6e..9e4db7407f1a 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts
@@ -111,7 +111,7 @@
 		};
 	};
 
-	regulator_3_3v: vcc3p3-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC3P3";
 		regulator-min-microvolt = <3300000>;
@@ -169,13 +169,11 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts
index 8d5d3996f6f2..ca18b959e655 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts
@@ -80,7 +80,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts
index 99a71757cdf4..ce0d6514eeb5 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts
@@ -26,7 +26,7 @@
 		ethernet0 = &gmac1;
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -113,16 +113,14 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q512a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q512a";
+		compatible = "micron,n25q512a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
index a060718758b6..65f390bf8975 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
@@ -141,7 +141,7 @@
 		reg = <0x50>;
 	};
 
-	i2cswitch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -221,16 +221,14 @@
 &qspi {
 	status = "okay";
 
-	n25q128@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q128";
+		compatible = "micron,n25q128", "jedec,spi-nor";
 		reg = <0>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
 
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
@@ -238,16 +236,14 @@
 		cdns,tslch-ns = <4>;
 	};
 
-	n25q00@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <1>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
 
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_vt.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts
index a77846f73b34..845ab2cc5ce6 100644
--- a/arch/arm/boot/dts/socfpga_vt.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts
@@ -29,7 +29,7 @@
 			};
 		};
 
-		dwmmc0@ff704000 {
+		mmc@ff704000 {
 			broken-cd;
 			bus-width = <4>;
 			cap-mmc-highspeed;
@@ -57,11 +57,11 @@
 			clock-frequency = <7000000>;
 		};
 
-		serial0@ffc02000 {
+		serial@ffc02000 {
 			clock-frequency = <7372800>;
 		};
 
-		serial1@ffc03000 {
+		serial@ffc03000 {
 			clock-frequency = <7372800>;
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6192.dts b/arch/arm/boot/dts/kirkwood-rd88f6192.dts
deleted file mode 100644
index 712d6042b132..000000000000
--- a/arch/arm/boot/dts/kirkwood-rd88f6192.dts
+++ /dev/null
@@ -1,106 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Marvell RD88F6192 Board descrition
- *
- * Andrew Lunn <andrew@lunn.ch>
- *
- * This file contains the definitions that are common between the three
- * variants of the Marvell Kirkwood Development Board.
- */
-/dts-v1/;
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6192.dtsi"
-
-/ {
-	model = "Marvell RD88F6192 reference design";
-	compatible = "marvell,rd88f6192", "marvell,kirkwood-88f6192", "marvell,kirkwood";
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-		stdout-path = &uart0;
-	};
-
-	ocp@f1000000 {
-		pinctrl: pin-controller@10000 {
-			pinctrl-0 = <&pmx_usb_power>;
-			pinctrl-names = "default";
-
-                        pmx_usb_power: pmx-usb-power {
-                                marvell,pins = "mpp10";
-                                marvell,function = "gpo";
-                        };
-		};
-
-		serial@12000 {
-			status = "okay";
-
-		};
-
-		spi@10600 {
-			status = "okay";
-
-			m25p128@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "st,m25p128", "jedec,spi-nor";
-				reg = <0>;
-				spi-max-frequency = <20000000>;
-				mode = <0>;
-			};
-		};
-
-		sata@80000 {
-			status = "okay";
-			nr-ports = <2>;
-		};
-	};
-
-	regulators {
-                compatible = "simple-bus";
-                #address-cells = <1>;
-                #size-cells = <0>;
-                pinctrl-0 = <&pmx_usb_power>;
-                pinctrl-names = "default";
-
-                usb_power: regulator@0 {
-                        compatible = "regulator-fixed";
-                        reg = <0>;
-                        regulator-name = "USB VBUS";
-                        regulator-min-microvolt = <5000000>;
-                        regulator-max-microvolt = <5000000>;
-                        enable-active-high;
-                        regulator-always-on;
-                        regulator-boot-on;
-                        gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>;
-                };
-	};
-};
-
-&mdio {
-        status = "okay";
-
-        ethphy0: ethernet-phy@8 {
-                reg = <8>;
-        };
-};
-
-&eth0 {
-        status = "okay";
-        ethernet0-port@0 {
-                phy-handle = <&ethphy0>;
-        };
-};
-
-&pciec {
-        status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
deleted file mode 100644
index 2a0a98fe67f0..000000000000
--- a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
+++ /dev/null
@@ -1,13 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-
-/dts-v1/;
-
-#include "omap34xx.dtsi"
-#include "logicpd-som-lv.dtsi"
-#include "logicpd-som-lv-baseboard.dtsi"
-#include "omap-gpmc-smsc9221.dtsi"
-
-/ {
-	model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
-	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
-};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
deleted file mode 100644
index a604d92221a4..000000000000
--- a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
+++ /dev/null
@@ -1,13 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-
-/dts-v1/;
-
-#include "omap36xx.dtsi"
-#include "logicpd-som-lv.dtsi"
-#include "logicpd-som-lv-baseboard.dtsi"
-#include "omap-gpmc-smsc9221.dtsi"
-
-/ {
-	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
-	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
-};
diff --git a/arch/arm/boot/dts/marvell/Makefile b/arch/arm/boot/dts/marvell/Makefile
new file mode 100644
index 000000000000..1e0f5ff492f7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/Makefile
@@ -0,0 +1,165 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MMP) += \
+	pxa168-aspenite.dtb \
+	pxa910-dkb.dtb \
+	mmp2-brownstone.dtb \
+	mmp2-olpc-xo-1-75.dtb \
+	mmp3-dell-ariel.dtb
+dtb-$(CONFIG_ARCH_ORION5X) += \
+	orion5x-kuroboxpro.dtb \
+	orion5x-lacie-d2-network.dtb \
+	orion5x-lacie-ethernet-disk-mini-v2.dtb \
+	orion5x-linkstation-lsgl.dtb \
+	orion5x-linkstation-lswtgl.dtb \
+	orion5x-linkstation-lschl.dtb \
+	orion5x-lswsgl.dtb \
+	orion5x-maxtor-shared-storage-2.dtb \
+	orion5x-netgear-wnr854t.dtb \
+	orion5x-rd88f5182-nas.dtb
+dtb-$(CONFIG_MACH_ARMADA_370) += \
+	armada-370-c200-v2.dtb \
+	armada-370-db.dtb \
+	armada-370-dlink-dns327l.dtb \
+	armada-370-mirabox.dtb \
+	armada-370-netgear-rn102.dtb \
+	armada-370-netgear-rn104.dtb \
+	armada-370-rd.dtb \
+	armada-370-seagate-nas-2bay.dtb \
+	armada-370-seagate-nas-4bay.dtb \
+	armada-370-seagate-personal-cloud.dtb \
+	armada-370-seagate-personal-cloud-2bay.dtb \
+	armada-370-synology-ds213j.dtb
+dtb-$(CONFIG_MACH_ARMADA_375) += \
+	armada-375-db.dtb
+dtb-$(CONFIG_MACH_ARMADA_38X) += \
+	armada-381-netgear-gs110emx.dtb \
+	armada-382-rd-ac3x-48g4x2xl.dtb \
+	armada-385-atl-x530.dtb \
+	armada-385-clearfog-gtr-s4.dtb \
+	armada-385-clearfog-gtr-l8.dtb \
+	armada-385-db-88f6820-amc.dtb \
+	armada-385-db-ap.dtb \
+	armada-385-linksys-caiman.dtb \
+	armada-385-linksys-cobra.dtb \
+	armada-385-linksys-rango.dtb \
+	armada-385-linksys-shelby.dtb \
+	armada-385-synology-ds116.dtb \
+	armada-385-turris-omnia.dtb \
+	armada-388-clearfog.dtb \
+	armada-388-clearfog-base.dtb \
+	armada-388-clearfog-pro.dtb \
+	armada-388-db.dtb \
+	armada-388-gp.dtb \
+	armada-388-helios4.dtb \
+	armada-388-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_39X) += \
+	armada-390-db.dtb \
+	armada-395-gp.dtb \
+	armada-398-db.dtb
+dtb-$(CONFIG_MACH_ARMADA_XP) += \
+	armada-xp-axpwifiap.dtb \
+	armada-xp-crs305-1g-4s.dtb \
+	armada-xp-crs305-1g-4s-bit.dtb \
+	armada-xp-crs326-24g-2s.dtb \
+	armada-xp-crs326-24g-2s-bit.dtb \
+	armada-xp-crs328-4c-20s-4s.dtb \
+	armada-xp-crs328-4c-20s-4s-bit.dtb \
+	armada-xp-db.dtb \
+	armada-xp-db-dxbc2.dtb \
+	armada-xp-db-xc3-24g4xg.dtb \
+	armada-xp-gp.dtb \
+	armada-xp-lenovo-ix4-300d.dtb \
+	armada-xp-linksys-mamba.dtb \
+	armada-xp-matrix.dtb \
+	armada-xp-netgear-rn2120.dtb \
+	armada-xp-openblocks-ax3-4.dtb \
+	armada-xp-synology-ds414.dtb
+dtb-$(CONFIG_MACH_DOVE) += \
+	dove-cubox.dtb \
+	dove-cubox-es.dtb \
+	dove-d2plug.dtb \
+	dove-d3plug.dtb \
+	dove-dove-db.dtb \
+	dove-sbc-a510.dtb
+dtb-$(CONFIG_MACH_KIRKWOOD) += \
+	kirkwood-4i-edge-200.dtb \
+	kirkwood-b3.dtb \
+	kirkwood-blackarmor-nas220.dtb \
+	kirkwood-c200-v1.dtb \
+	kirkwood-cloudbox.dtb \
+	kirkwood-d2net.dtb \
+	kirkwood-db-88f6281.dtb \
+	kirkwood-db-88f6282.dtb \
+	kirkwood-dir665.dtb \
+	kirkwood-dns320.dtb \
+	kirkwood-dns325.dtb \
+	kirkwood-dockstar.dtb \
+	kirkwood-dreamplug.dtb \
+	kirkwood-ds109.dtb \
+	kirkwood-ds110jv10.dtb \
+	kirkwood-ds111.dtb \
+	kirkwood-ds112.dtb \
+	kirkwood-ds209.dtb \
+	kirkwood-ds210.dtb \
+	kirkwood-ds212.dtb \
+	kirkwood-ds212j.dtb \
+	kirkwood-ds409.dtb \
+	kirkwood-ds409slim.dtb \
+	kirkwood-ds411.dtb \
+	kirkwood-ds411j.dtb \
+	kirkwood-ds411slim.dtb \
+	kirkwood-goflexnet.dtb \
+	kirkwood-guruplug-server-plus.dtb \
+	kirkwood-ib62x0.dtb \
+	kirkwood-iconnect.dtb \
+	kirkwood-iomega_ix2_200.dtb \
+	kirkwood-is2.dtb \
+	kirkwood-km_fixedeth.dtb \
+	kirkwood-km_kirkwood.dtb \
+	kirkwood-l-50.dtb \
+	kirkwood-laplug.dtb \
+	kirkwood-linkstation-lsqvl.dtb \
+	kirkwood-linkstation-lsvl.dtb \
+	kirkwood-linkstation-lswsxl.dtb \
+	kirkwood-linkstation-lswvl.dtb \
+	kirkwood-linkstation-lswxl.dtb \
+	kirkwood-linksys-viper.dtb \
+	kirkwood-lschlv2.dtb \
+	kirkwood-lsxhl.dtb \
+	kirkwood-mplcec4.dtb \
+	kirkwood-mv88f6281gtw-ge.dtb \
+	kirkwood-nas2big.dtb \
+	kirkwood-net2big.dtb \
+	kirkwood-net5big.dtb \
+	kirkwood-netgear_readynas_duo_v2.dtb \
+	kirkwood-netgear_readynas_nv+_v2.dtb \
+	kirkwood-ns2.dtb \
+	kirkwood-ns2lite.dtb \
+	kirkwood-ns2max.dtb \
+	kirkwood-ns2mini.dtb \
+	kirkwood-nsa310.dtb \
+	kirkwood-nsa310a.dtb \
+	kirkwood-nsa310s.dtb \
+	kirkwood-nsa320.dtb \
+	kirkwood-nsa325.dtb \
+	kirkwood-openblocks_a6.dtb \
+	kirkwood-openblocks_a7.dtb \
+	kirkwood-openrd-base.dtb \
+	kirkwood-openrd-client.dtb \
+	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
+	kirkwood-pogoplug-series-4.dtb \
+	kirkwood-rd88f6192.dtb \
+	kirkwood-rd88f6281-z0.dtb \
+	kirkwood-rd88f6281-a.dtb \
+	kirkwood-rs212.dtb \
+	kirkwood-rs409.dtb \
+	kirkwood-rs411.dtb \
+	kirkwood-sheevaplug.dtb \
+	kirkwood-sheevaplug-esata.dtb \
+	kirkwood-t5325.dtb \
+	kirkwood-topkick.dtb \
+	kirkwood-ts219-6281.dtb \
+	kirkwood-ts219-6282.dtb \
+	kirkwood-ts419-6281.dtb \
+	kirkwood-ts419-6282.dtb
diff --git a/arch/arm/boot/dts/marvell/armada-370-c200-v2.dts b/arch/arm/boot/dts/marvell/armada-370-c200-v2.dts
new file mode 100644
index 000000000000..84d40e1d70ef
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-370-c200-v2.dts
@@ -0,0 +1,388 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Device Tree file for Ctera C200-V2
+ *
+ * Copyright (C) 2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Ctera C200 V2";
+	compatible = "ctera,c200-v2", "marvell,armada370", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1024 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+	};
+
+	thermal-zones {
+		ethphy-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&ethphy0>;
+
+			trips {
+				ethphy_alert1: trip1 {
+					temperature = <65000>;
+					hysteresis = <4000>;
+					type = "passive";
+				};
+
+				ethphy_crit: trip2 {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	beeper {
+		compatible = "pwm-beeper";
+		pinctrl-0 = <&pmx_beeper>;
+		pinctrl-names = "default";
+		pwms = <&gpio1 31 4000>;
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_poweroff>;
+		pinctrl-names = "default";
+		gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+
+		button-power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		};
+
+		button-usb1 {
+			label = "USB1 Button";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button-usb2 {
+			label = "USB2 Button";
+			linux,code = <BTN_1>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+		pinctrl-names = "default";
+
+		led-0 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-8 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-9 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+		};
+
+		led-10 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led-11 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-12 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&coherencyfab {
+	broken-idle;
+};
+
+&eth1 {
+	pinctrl-0 = <&ge1_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-handle = <&ethphy0>;
+	phy-connection-type = "rgmii-id";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <100000>;
+	status = "okay";
+
+	hwmon@2a {
+		compatible = "nuvoton,nct7802";
+		reg = <0x2a>;
+	};
+
+	rtc@30 {
+		compatible = "sii,s35390a";
+		reg = <0x30>;
+	};
+};
+
+&mdio {
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+
+	ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
+		reg = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "pxa3xx_nand-0";
+		nand-rb = <0>;
+		marvell,nand-keep-config;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x0000000 0x200000>;
+				read-only;
+			};
+
+			partition@200000 {
+				label = "certificate";
+				reg = <0x0200000 0x100000>;
+				read-only;
+			};
+
+			partition@300000 {
+				label = "preset_cfg";
+				reg = <0x0300000 0x100000>;
+				read-only;
+			};
+
+			partition@400000 {
+				label = "dev_params";
+				reg = <0x0400000 0x100000>;
+				read-only;
+			};
+			partition@500000 {
+				label = "active_bank";
+				reg = <0x0500000 0x0100000>;
+			};
+
+			partition@600000 {
+				label = "magic";
+				reg = <0x0600000 0x0100000>;
+				read-only;
+			};
+
+			partition@700000 {
+				label = "bank1";
+				reg = <0x0700000 0x2800000>;
+			};
+
+			partition@2f00000 {
+				label = "bank2";
+				reg = <0x2f00000 0x2800000>;
+			};
+
+			/* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+			partition@5a00000 {
+				label = "reserved";
+				reg = <0x5a00000 0x2000000>;
+			};
+
+			partition@7a00000 {
+				label = "rootfs";
+				reg = <0x7a00000 0x8600000>;
+			};
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+
+	pcie@1,0 { /* Renesas uPD720202 USB 3.0 controller */
+		pinctrl-0 = <&pmx_pcie>;
+		pinctrl-names = "default";
+		status = "okay";
+		reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	pmx_poweroff: pmx-poweroff {
+		marvell,pins = "mpp7";
+		marvell,function = "gpo";
+	};
+
+	pmx_power_cpu: pmx-power-cpu {
+		marvell,pins = "mpp4";
+		marvell,function = "vdd";
+	};
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp6", "mpp10", "mpp14", "mpp32";
+		marvell,function = "gpio";
+	};
+
+	pmx_leds1: pmx-leds1 {
+		marvell,pins = "mpp47";
+		marvell,function = "gpo";
+	};
+
+	pmx_leds2: pmx-leds2 {
+		marvell,pins = "mpp12", "mpp13", "mpp15", "mpp16", "mpp50", "mpp51",
+			       "mpp52", "mpp53", "mpp55", "mpp56", "mpp57", "mpp58";
+		marvell,function = "gpio";
+	};
+
+	pmx_pcie: pmx-pcie {
+		marvell,pins = "mpp59";
+		marvell,function = "gpio";
+	};
+
+	pmx_beeper: pmx-beeper {
+		marvell,pins = "mpp63";
+		marvell,function = "gpio";
+	};
+};
+
+&pmsu {
+	pinctrl-0 = <&pmx_power_cpu>;
+	pinctrl-names = "default";
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	nr-ports = <2>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hdd0_temp: sata-port@0 {
+		reg = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	hdd1_temp: sata-port@1 {
+		reg = <1>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/marvell/armada-370-db.dts
index 77261a2fb949..a7dc4c04d10b 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-db.dts
@@ -203,7 +203,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "mx25l25635e", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts b/arch/arm/boot/dts/marvell/armada-370-dlink-dns327l.dts
index baa459dd51e4..d4c4efabd254 100644
--- a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-dlink-dns327l.dts
@@ -86,73 +86,64 @@
 
 		pinctrl-names = "default";
 
-		sata-r-amber-pin {
+		led-sata-r-amber {
 			label = "dns327l:amber:sata-r";
 			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 
-		sata-l-amber-pin {
+		led-sata-l-amber {
 			label = "dns327l:amber:sata-l";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 
-		backup-led-pin {
+		led-backup {
 			label = "dns327l:white:usb";
 			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			pinctrl-0 = <&xhci_pwr_pin>;
-			pinctrl-names = "default";
-			regulator-name = "USB3.0 Port Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-boot-on;
-			regulator-always-on;
-			gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-		};
+	usb_power: regulator-1 {
+		compatible = "regulator-fixed";
+		pinctrl-0 = <&xhci_pwr_pin>;
+		pinctrl-names = "default";
+		regulator-name = "USB3.0 Port Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+		gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+	};
 
-		sata_r_power: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			pinctrl-0 = <&sata_r_pwr_pin>;
-			pinctrl-names = "default";
-			regulator-name = "SATA-R Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <2000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		};
+	sata_r_power: regulator-2 {
+		compatible = "regulator-fixed";
+		pinctrl-0 = <&sata_r_pwr_pin>;
+		pinctrl-names = "default";
+		regulator-name = "SATA-R Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <2000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+	};
 
-		sata_l_power: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			pinctrl-0 = <&sata_l_pwr_pin>;
-			pinctrl-names = "default";
-			regulator-name = "SATA-L Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <4000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-		};
+	sata_l_power: regulator-3 {
+		compatible = "regulator-fixed";
+		pinctrl-0 = <&sata_l_pwr_pin>;
+		pinctrl-names = "default";
+		regulator-name = "SATA-L Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <4000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -247,9 +238,8 @@
 &mdio {
 	phy0: ethernet-phy@0 { /* Marvell 88E1318 */
 		reg = <0>;
-		marvell,reg-init = <0x0 0x16 0x0 0x0002>,
-				<0x0 0x19 0x0 0x0077>,
-				<0x0 0x18 0x0 0x5747>;
+		marvell,reg-init = <0x2 0x19 0x0 0x0077>,
+				   <0x2 0x18 0x0 0x5747>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/marvell/armada-370-mirabox.dts
index 7c2f5a79b50d..7c2f5a79b50d 100644
--- a/arch/arm/boot/dts/armada-370-mirabox.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-mirabox.dts
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/marvell/armada-370-netgear-rn102.dts
index b0b640b7de40..079b37cf148a 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-netgear-rn102.dts
@@ -85,11 +85,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <8192>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <8192>;
+		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/marvell/armada-370-netgear-rn104.dts
index 85e2e9e27a9f..d752ac1d7b58 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-netgear-rn104.dts
@@ -94,11 +94,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <8192>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <8192>;
+		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/marvell/armada-370-rd.dts
index c910d157a686..f23f6b3fc8f3 100644
--- a/arch/arm/boot/dts/armada-370-rd.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-rd.dts
@@ -20,6 +20,7 @@
 /dts-v1/;
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/gpio/gpio.h>
 #include "armada-370.dtsi"
 
@@ -61,8 +62,8 @@
 				status = "okay";
 				phy-mode = "rgmii-id";
 				fixed-link {
-					   speed = <1000>;
-					   full-duplex;
+					speed = <1000>;
+					full-duplex;
 				};
 			};
 
@@ -84,8 +85,6 @@
 
 			gpio-keys {
 				compatible = "gpio-keys";
-				#address-cells = <1>;
-				#size-cells = <0>;
 				button {
 					label = "Software Button";
 					linux,code = <KEY_POWER>;
@@ -96,7 +95,7 @@
 			gpio-fan {
 				compatible = "gpio-fan";
 				gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
-				gpio-fan,speed-map = <0 0 3000 1>;
+				gpio-fan,speed-map = <0 0>, <3000 1>;
 				pinctrl-0 = <&fan_pins>;
 				pinctrl-names = "default";
 			};
@@ -137,44 +136,53 @@
 	pinctrl-names = "default";
 	phy0: ethernet-phy@0 {
 		reg = <0>;
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_WHITE>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 
-	switch: switch@10 {
+	switch: ethernet-switch@10 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0x10>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan0";
 			};
 
-			port@1 {
-			       reg = <1>;
-			       label = "lan1";
+			ethernet-port@1 {
+				reg = <1>;
+				label = "lan1";
 			};
 
-			port@2 {
-			       reg = <2>;
-			       label = "lan2";
+			ethernet-port@2 {
+				reg = <2>;
+				label = "lan2";
 			};
 
-			port@3 {
-			       reg = <3>;
-			       label = "lan3";
+			ethernet-port@3 {
+				reg = <3>;
+				label = "lan3";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
 				ethernet = <&eth1>;
+				phy-mode = "rgmii-id";
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
@@ -186,25 +194,25 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switchphy0: switchphy@0 {
+			switchphy0: ethernet-phy@0 {
 				reg = <0>;
 				interrupt-parent = <&switch>;
 				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			switchphy1: switchphy@1 {
+			switchphy1: ethernet-phy@1 {
 				reg = <1>;
 				interrupt-parent = <&switch>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			switchphy2: switchphy@2 {
+			switchphy2: ethernet-phy@2 {
 				reg = <2>;
 				interrupt-parent = <&switch>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			switchphy3: switchphy@3 {
+			switchphy3: ethernet-phy@3 {
 				reg = <3>;
 				interrupt-parent = <&switch>;
 				interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-2bay.dts
index 8dd242e668e6..6ec3dd3337f4 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-2bay.dts
@@ -25,9 +25,9 @@
 
 	gpio-fan {
 		gpio-fan,speed-map =
-			<   0 3
-			  950 2
-			 1400 1
-			 1800 0>;
+			<   0 3>,
+			< 950 2>,
+			<1400 1>,
+			<1800 0>;
 	};
 };
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-4bay.dts
index 3cf70c72c5ca..3011578a3124 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-4bay.dts
@@ -46,37 +46,34 @@
 		};
 	};
 
-	regulators {
-		regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "SATA2 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pca9554 6 GPIO_ACTIVE_HIGH>;
-		};
-		regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "SATA3 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pca9554 7 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA2 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pca9554 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA3 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pca9554 7 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-leds {
-		red-sata2 {
+		led-red-sata2 {
 			label = "dart:red:sata2";
 			gpios = <&pca9554 0 GPIO_ACTIVE_LOW>;
 		};
-		red-sata3 {
+		led-red-sata3 {
 			label = "dart:red:sata3";
 			gpios = <&pca9554 3 GPIO_ACTIVE_LOW>;
 		};
@@ -109,10 +106,10 @@
 
 	gpio-fan {
 		gpio-fan,speed-map =
-			<   0 3
-			  800 2
-			  1050 1
-			  1300 0>;
+			<   0 3>,
+			< 800 2>,
+			<1050 1>,
+			<1300 0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-xbay.dtsi
index b52634ecf1d9..ffb3179033e7 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-xbay.dtsi
@@ -70,34 +70,26 @@
 
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-names = "default";
-
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA0 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-		};
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA1 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA0 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	};
+
+	regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-fan {
@@ -108,22 +100,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		backup {
+		button-backup {
 			label = "Backup button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
@@ -134,21 +124,21 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		white-power {
+		led-white-power {
 			label = "dart:white:power";
 			gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 
 		};
-		red-power {
+		led-red-power {
 			label = "dart:red:power";
 			gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
 		};
-		red-sata0 {
+		led-red-sata0 {
 			label = "dart:red:sata0";
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		red-sata1 {
+		led-red-sata1 {
 			label = "dart:red:sata1";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud-2bay.dts
index 5ee572dc9242..45d8ec5dfeb7 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud-2bay.dts
@@ -32,17 +32,14 @@
 		};
 	};
 
-	regulators {
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA1 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
 	};
 };
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dts
index 578b54b39c8f..578b54b39c8f 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dts
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dtsi
index a624b2371fb6..054124857235 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dtsi
@@ -53,52 +53,43 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
-		};
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA0 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	};
+
+	regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA0 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		button {
+		button-usb {
 			label = "USB VBUS error";
 			linux,code = <KEY_UNKNOWN>;
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
@@ -109,7 +100,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		red-sata0 {
+		led-red-sata0 {
 			label = "cumulus:red:sata0";
 			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -159,7 +150,7 @@
 	pinctrl-0 = <&spi0_pins2>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		/* MX25L8006E */
diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/marvell/armada-370-synology-ds213j.dts
index 64f2ce254fb6..02599a3e9816 100644
--- a/arch/arm/boot/dts/armada-370-synology-ds213j.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-synology-ds213j.dts
@@ -91,9 +91,9 @@
 			};
 
 			ethernet@70000 {
-			       status = "okay";
-			       phy = <&phy1>;
-			       phy-mode = "sgmii";
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "sgmii";
 			};
 
 			sata@a0000 {
@@ -113,14 +113,14 @@
 			 &gpio2  0 GPIO_ACTIVE_HIGH
 			 &gpio2  1 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       1000 1
-				       1150 2
-				       1350 4
-				       1500 3
-				       1650 5
-				       1750 6
-				       1900 7 >;
+		gpio-fan,speed-map = <   0 0>,
+				     <1000 1>,
+				     <1150 2>,
+				     <1350 4>,
+				     <1500 3>,
+				     <1650 5>,
+				     <1750 6>,
+				     <1900 7>;
 	};
 
 	gpio-leds {
@@ -142,38 +142,32 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>;
+	sata1_regulator: sata1-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <2000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata1_pwr_pin>;
 		pinctrl-names = "default";
+	};
 
-		sata1_regulator: sata1-regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA1 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <2000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
-		};
-
-		sata2_regulator: sata2-regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA2 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <4000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		};
+	sata2_regulator: sata2-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA2 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <4000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata2_pwr_pin>;
+		pinctrl-names = "default";
 	};
 };
 
@@ -258,7 +252,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q064", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/marvell/armada-370-xp.dtsi
index c15f5e92f97f..0b8c2a64b36f 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370-xp.dtsi
@@ -114,7 +114,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <31>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -124,7 +123,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <32>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/marvell/armada-370.dtsi
index 46e6d3ed8f35..2013a5ccecd3 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370.dtsi
@@ -60,34 +60,54 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
                                           0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x80000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
                                           0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/marvell/armada-375-db.dts
index 0e679465cbb5..4c4092790a20 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-375-db.dts
@@ -64,7 +64,7 @@
 
 	status = "disabled";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/marvell/armada-375.dtsi
index 2932a29ae272..ddc49547d786 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-375.dtsi
@@ -178,6 +178,8 @@
 
 			/* Network controller */
 			ethernet: ethernet@f0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "marvell,armada-375-pp2";
 				reg = <0xf0000 0xa000>, /* Packet Processor regs */
 				      <0xc0000 0x3060>, /* LMS regs */
@@ -187,15 +189,17 @@
 				clock-names = "pp_clk", "gop_clk";
 				status = "disabled";
 
-				eth0: eth0 {
+				eth0: ethernet-port@0 {
 					interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-					port-id = <0>;
+					reg = <0>;
+					port-id = <0>; /* For backward compatibility. */
 					status = "disabled";
 				};
 
-				eth1: eth1 {
+				eth1: ethernet-port@1 {
 					interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
-					port-id = <1>;
+					reg = <1>;
+					port-id = <1>; /* For backward compatibility. */
 					status = "disabled";
 				};
 			};
@@ -236,7 +240,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -247,7 +250,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -428,7 +430,7 @@
 				status = "disabled";
 			};
 
-			usb2: usb3@58000 {
+			usb2: usb@58000 {
 				compatible = "marvell,armada-375-xhci";
 				reg = <0x58000 0x20000>,<0x5b880 0x80>;
 				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
@@ -570,34 +572,54 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 		};
diff --git a/arch/arm/boot/dts/armada-380.dtsi b/arch/arm/boot/dts/marvell/armada-380.dtsi
index cff1269f3fbf..e94f22b0e9b5 100644
--- a/arch/arm/boot/dts/armada-380.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-380.dtsi
@@ -64,54 +64,84 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts b/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
new file mode 100644
index 000000000000..5baf83e5253d
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
@@ -0,0 +1,293 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2021, Marcel Ziswiler <marcel@ziswiler.com> */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear GS110EMX";
+	compatible = "netgear,gs110emx", "marvell,armada380";
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&front_button_pins>;
+		pinctrl-names = "default";
+
+		key-factory-default {
+			label = "Factory Default";
+			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>; /* 128 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+			rtc@a3800 {
+				/*
+				 * If the rtc doesn't work, run "date reset"
+				 * twice in u-boot.
+				 */
+				status = "okay";
+			};
+		};
+	};
+};
+
+&eth0 {
+	/* ethernet@70000 */
+	bm,pool-long = <0>;
+	bm,pool-short = <1>;
+	buffer-manager = <&bm>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&ge0_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	fixed-link {
+		full-duplex;
+		pause;
+		speed = <1000>;
+	};
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+	status = "okay";
+
+	ethernet-switch@0 {
+		compatible = "marvell,mv88e6190";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&switch_interrupt_pins>;
+		pinctrl-names = "default";
+		reg = <0>;
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy1: ethernet-phy@1 {
+				reg = <0x1>;
+			};
+
+			switch0phy2: ethernet-phy@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy3: ethernet-phy@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy4: ethernet-phy@4 {
+				reg = <0x4>;
+			};
+
+			switch0phy5: ethernet-phy@5 {
+				reg = <0x5>;
+			};
+
+			switch0phy6: ethernet-phy@6 {
+				reg = <0x6>;
+			};
+
+			switch0phy7: ethernet-phy@7 {
+				reg = <0x7>;
+			};
+
+			switch0phy8: ethernet-phy@8 {
+				reg = <0x8>;
+			};
+		};
+
+		mdio-external {
+			compatible = "marvell,mv88e6xxx-mdio-external";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			phy1: ethernet-phy@b {
+				reg = <0xb>;
+				compatible = "ethernet-phy-ieee802.3-c45";
+			};
+
+			phy2: ethernet-phy@c {
+				reg = <0xc>;
+				compatible = "ethernet-phy-ieee802.3-c45";
+			};
+		};
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet-port@0 {
+				ethernet = <&eth0>;
+				phy-mode = "rgmii";
+				reg = <0>;
+
+				fixed-link {
+					full-duplex;
+					pause;
+					speed = <1000>;
+				};
+			};
+
+			ethernet-port@1 {
+				label = "lan1";
+				phy-handle = <&switch0phy1>;
+				reg = <1>;
+			};
+
+			ethernet-port@2 {
+				label = "lan2";
+				phy-handle = <&switch0phy2>;
+				reg = <2>;
+			};
+
+			ethernet-port@3 {
+				label = "lan3";
+				phy-handle = <&switch0phy3>;
+				reg = <3>;
+			};
+
+			ethernet-port@4 {
+				label = "lan4";
+				phy-handle = <&switch0phy4>;
+				reg = <4>;
+			};
+
+			ethernet-port@5 {
+				label = "lan5";
+				phy-handle = <&switch0phy5>;
+				reg = <5>;
+			};
+
+			ethernet-port@6 {
+				label = "lan6";
+				phy-handle = <&switch0phy6>;
+				reg = <6>;
+			};
+
+			ethernet-port@7 {
+				label = "lan7";
+				phy-handle = <&switch0phy7>;
+				reg = <7>;
+			};
+
+			ethernet-port@8 {
+				label = "lan8";
+				phy-handle = <&switch0phy8>;
+				reg = <8>;
+			};
+
+			ethernet-port@9 {
+				/* 88X3310P external phy */
+				label = "lan9";
+				phy-handle = <&phy1>;
+				phy-mode = "xaui";
+				reg = <9>;
+			};
+
+			ethernet-port@a {
+				/* 88X3310P external phy */
+				label = "lan10";
+				phy-handle = <&phy2>;
+				phy-mode = "xaui";
+				reg = <0xa>;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	front_button_pins: front-button-pins {
+		marvell,pins = "mpp38";
+		marvell,function = "gpio";
+	};
+
+	switch_interrupt_pins: switch-interrupt-pins {
+		marvell,pins = "mpp39";
+		marvell,function = "gpio";
+	};
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <3000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot";
+				read-only;
+				reg = <0x00000000 0x00100000>;
+			};
+
+			partition@100000 {
+				label = "env";
+				reg = <0x00100000 0x00010000>;
+			};
+
+			partition@200000 {
+				label = "rsv";
+				reg = <0x00110000 0x00010000>;
+			};
+
+			partition@300000 {
+				label = "image0";
+				reg = <0x00120000 0x00900000>;
+			};
+
+			partition@400000 {
+				label = "config";
+				reg = <0x00a20000 0x00300000>;
+			};
+
+			partition@480000 {
+				label = "debug";
+				reg = <0x00d20000 0x002e0000>;
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/marvell/armada-382-rd-ac3x-48g4x2xl.dts b/arch/arm/boot/dts/marvell/armada-382-rd-ac3x-48g4x2xl.dts
new file mode 100644
index 000000000000..6ab65d21861a
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-382-rd-ac3x-48g4x2xl.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Marvell Armada 382 reference board
+ * (RD-AC3X-48G4X2XL)
+ *
+ * Copyright (C) 2020 Allied Telesis Labs
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Marvell Armada 382 RD-AC3X";
+	compatible = "marvell,rd-ac3x-48g4x2xl", "marvell,rd-ac3x",
+			 "marvell,armada385", "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		ethernet0 = &eth1;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	eeprom@53 {
+		compatible = "atmel,24c64";
+		reg = <0x53>;
+	};
+
+	/* CPLD device present at 0x3c. Function unknown */
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&eth1 {
+	status = "okay";
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie1 {
+	/* Port 0, Lane 0 */
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "pxa3xx_nand-0";
+		nand-rb = <0>;
+		nand-on-flash-bbt;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				reg = <0x00000000 0x00500000>;
+				label = "u-boot";
+			};
+			partition@500000 {
+				reg = <0x00500000 0x00400000>;
+				label = "u-boot env";
+			};
+			partition@900000 {
+				reg = <0x00900000 0x3F700000>;
+				label = "user";
+			};
+		};
+	};
+};
+
+&refclk {
+	clock-frequency = <200000000>;
+};
diff --git a/arch/arm/boot/dts/marvell/armada-385-atl-x530.dts b/arch/arm/boot/dts/marvell/armada-385-atl-x530.dts
new file mode 100644
index 000000000000..5a9ab8410b7b
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-385-atl-x530.dts
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Armada 385 Allied Telesis x530/GS980MX Board.
+ (x530/AT-GS980MX)
+ *
+ Copyright (C) 2020 Allied Telesis Labs
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "x530/AT-GS980MX";
+	compatible = "alliedtelesis,gs980mx", "alliedtelesis,x530", "marvell,armada385", "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x3d) 0 0xf4800000 0x80000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			i2c0: i2c@11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+			};
+
+			uart0: serial@12000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart0_pins>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+	reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <400000>;
+};
+
+&pcie2 {
+	status = "okay";
+};
+
+&devbus_cs1 {
+	compatible = "marvell,mvebu-devbus";
+	status = "okay";
+
+	devbus,bus-width    = <8>;
+	devbus,turn-off-ps  = <60000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <124000>;
+	devbus,acc-next-ps  = <248000>;
+	devbus,rd-setup-ps  = <0>;
+	devbus,rd-hold-ps   = <0>;
+
+	/* Write parameters */
+	devbus,sync-enable = <0>;
+	devbus,wr-high-ps  = <60000>;
+	devbus,wr-low-ps   = <60000>;
+	devbus,ale-wr-ps   = <60000>;
+
+	nvs@0 {
+		status = "okay";
+
+		compatible = "mtd-ram";
+		reg = <0 0x00080000>;
+		bank-width = <1>;
+		label = "nvs";
+	};
+};
+
+&pinctrl {
+	i2c0_gpio_pins: i2c-gpio-pins-0 {
+		marvell,pins = "mpp2", "mpp3";
+		marvell,function = "gpio";
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-1 = <&i2c0_gpio_pins>;
+	scl-gpio = <&gpio0 2 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	sda-gpio = <&gpio0 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+	i2c0mux: mux@71 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "nxp,pca9544";
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		i2c@0 { /* POE devices MUX */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			adt7476_2e: hwmon@2e {
+				compatible = "adi,adt7476";
+				reg = <0x2e>;
+			};
+
+			adt7476_2d: hwmon@2d {
+				compatible = "adi,adt7476";
+				reg = <0x2d>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			rtc@68 {
+				compatible = "dallas,ds1340";
+				reg = <0x68>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			gpio@20 {
+				compatible = "nxp,pca9554";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	status = "okay";
+
+	flash@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <1>; /* Chip select 1 */
+		spi-max-frequency = <54000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				reg = <0x00000000 0x00100000>;
+				label = "u-boot";
+			};
+			partition@100000 {
+				reg = <0x00100000 0x00040000>;
+				label = "u-boot-env";
+			};
+			partition@140000 {
+				reg = <0x00140000 0x00e80000>;
+				label = "unused";
+			};
+			partition@fc0000 {
+				reg = <0x00fc0000 0x00040000>;
+				label = "idprom";
+			};
+		};
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "pxa3xx_nand-0";
+		nand-rb = <0>;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		marvell,nand-enable-arbiter;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				reg = <0x00000000 0x0f000000>;
+				label = "user";
+			};
+			partition@f000000 {
+				/* Maximum mtdoops size is 8MB, so set to that. */
+				reg = <0x0f000000 0x00800000>;
+				label = "errlog";
+			};
+			partition@f800000 {
+				reg = <0x0f800000 0x00800000>;
+				label = "nand-bbt";
+			};
+		};
+	};
+};
+
diff --git a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
new file mode 100644
index 000000000000..1707d1b01545
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "armada-385-clearfog-gtr.dtsi"
+
+/ {
+	model = "SolidRun Clearfog GTR L8";
+};
+
+&mdio {
+	switch0: ethernet-switch@4 {
+		compatible = "marvell,mv88e6190";
+		reg = <4>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
+		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet-port@1 {
+				reg = <1>;
+				label = "lan8";
+				phy-handle = <&switch0phy0>;
+			};
+
+			ethernet-port@2 {
+				reg = <2>;
+				label = "lan7";
+				phy-handle = <&switch0phy1>;
+			};
+
+			ethernet-port@3 {
+				reg = <3>;
+				label = "lan6";
+				phy-handle = <&switch0phy2>;
+			};
+
+			ethernet-port@4 {
+				reg = <4>;
+				label = "lan5";
+				phy-handle = <&switch0phy3>;
+			};
+
+			ethernet-port@5 {
+				reg = <5>;
+				label = "lan4";
+				phy-handle = <&switch0phy4>;
+			};
+
+			ethernet-port@6 {
+				reg = <6>;
+				label = "lan3";
+				phy-handle = <&switch0phy5>;
+			};
+
+			ethernet-port@7 {
+				reg = <7>;
+				label = "lan2";
+				phy-handle = <&switch0phy6>;
+			};
+
+			ethernet-port@8 {
+				reg = <8>;
+				label = "lan1";
+				phy-handle = <&switch0phy7>;
+			};
+
+			ethernet-port@10 {
+				reg = <10>;
+				phy-mode = "2500base-x";
+
+				ethernet = <&eth1>;
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: ethernet-phy@1 {
+				reg = <0x1>;
+			};
+
+			switch0phy1: ethernet-phy@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy2: ethernet-phy@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy3: ethernet-phy@4 {
+				reg = <0x4>;
+			};
+
+			switch0phy4: ethernet-phy@5 {
+				reg = <0x5>;
+			};
+
+			switch0phy5: ethernet-phy@6 {
+				reg = <0x6>;
+			};
+
+			switch0phy6: ethernet-phy@7 {
+				reg = <0x7>;
+			};
+
+			switch0phy7: ethernet-phy@8 {
+				reg = <0x8>;
+			};
+		};
+
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
new file mode 100644
index 000000000000..a7678a784c18
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "armada-385-clearfog-gtr.dtsi"
+
+/ {
+	model = "SolidRun Clearfog GTR S4";
+};
+
+&sfp0 {
+	tx-fault-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+};
+
+&mdio {
+	switch0: ethernet-switch@4 {
+		compatible = "marvell,mv88e6085";
+		reg = <4>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
+		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet-port@1 {
+				reg = <1>;
+				label = "lan2";
+				phy-handle = <&switch0phy0>;
+			};
+
+			ethernet-port@2 {
+				reg = <2>;
+				label = "lan1";
+				phy-handle = <&switch0phy1>;
+			};
+
+			ethernet-port@3 {
+				reg = <3>;
+				label = "lan4";
+				phy-handle = <&switch0phy2>;
+			};
+
+			ethernet-port@4 {
+				reg = <4>;
+				label = "lan3";
+				phy-handle = <&switch0phy3>;
+			};
+
+			ethernet-port@5 {
+				reg = <5>;
+				phy-mode = "2500base-x";
+				ethernet = <&eth1>;
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: ethernet-phy@11 {
+				reg = <0x11>;
+			};
+
+			switch0phy1: ethernet-phy@12 {
+				reg = <0x12>;
+			};
+
+			switch0phy2: ethernet-phy@13 {
+				reg = <0x13>;
+			};
+
+			switch0phy3: ethernet-phy@14 {
+				reg = <0x14>;
+			};
+		};
+
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
new file mode 100644
index 000000000000..d1452a04e904
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Clearfog GTR machines rev 1.0 (88F6825)
+ *
+ *  Rabeeh Khoury <rabeeh@solid-run.com>, based on Russell King clearfog work
+ */
+
+/*
+	SERDES mapping -
+	0. SATA1 on CON18, or optionally mini PCIe CON3 - PCIe0
+	1. 6141 switch (2.5Gbps capable)
+	2. SATA0 on CON17, or optionally mini PCIe CON4 - PCIe1
+	3. USB 3.0 Host
+	4. mini PCIe CON2 - PCIe2
+	5. SFP connector, or optionally SGMII Ethernet 1512 PHY
+
+	USB 2.0 mapping -
+	0. USB 2.0 - 0 USB pins header CON12
+	1. USB 2.0 - 1 mini PCIe CON2
+	2. USB 2.0 - 2 to USB 3.0 connector (used with SERDES #3)
+
+	Pin mapping -
+	0,1 - console UART
+	2,3 - I2C0 - connected to I2C EEPROM, two temperature sensors,
+	      front panel and PSE controller
+	4,5 - MDC/MDIO
+	6..17 - RGMII
+	18 - Topaz switch reset (active low)
+	19 - 1512 phy reset
+	20 - 1512 phy reset (eth2, optional)
+	21,28,37,38,39,40 - SD0
+	22 - USB 3.0 current limiter enable (active high)
+	24 - SFP TX fault (input active high)
+	25 - SFP present (input active low)
+	26,27 - I2C1 - connected to SFP
+	29 - Fan PWM
+	30 - CON4 mini PCIe wifi disable
+	31 - CON3 mini PCIe wifi disable
+	32 - Fuse programming power toggle (1.8v)
+	33 - CON4 mini PCIe reset
+	34 - CON2 mini PCIe wifi disable
+	35 - CON3 mini PCIe reset
+	36 - Rear button (GPIO active low)
+	41 - CON1 front panel connector
+	42 - Front LED1, or front panel CON1
+	43 - Micron L-PBGA 24 ball SPI (1Gb) CS, or TPM SPI CS
+	44 - CON2 mini PCIe reset
+	45 - TPM PIRQ signal, or front panel CON1
+	46 - SFP TX disable
+	47 - Control isolation of boot sensitive SAR signals
+	48 - PSE reset
+	49 - PSE OSS signal
+	50 - PSE interrupt
+	52 - Front LED2, or front panel
+	53 - Front button
+	54 - SFP LOS (input active high)
+	55 - Fan sense
+	56(mosi),57(clk),58(miso) - SPI interface - 32Mb SPI, 1Gb SPI and TPM
+	59 - SPI 32Mb W25Q32BVZPIG CS0 chip select (bootable)
+*/
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-385.dtsi"
+
+/ {
+	compatible = "marvell,armada385", "marvell,armada380";
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+		ethernet2 = &eth1;
+		ethernet3 = &eth2;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "5P0V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	v_usb3_con: regulator-v-usb3-con {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 22 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cf_gtr_usb3_con_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "v_usb3_con";
+		vin-supply = <&reg_5p0v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+
+			rtc@a3800 {
+				status = "okay";
+			};
+
+			i2c@11000 { /* ROM, temp sensor and front panel */
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			i2c@11100 { /* SFP (CON5/CON6) */
+				pinctrl-0 = <&cf_gtr_i2c1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins {
+					marvell,pins = "mpp18";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
+					marvell,pins = "mpp22";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_fan_pwm: cf-gtr-fan-pwm {
+					marvell,pins = "mpp23";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_i2c1_pins: i2c1-pins {
+					/* SFP */
+					marvell,pins = "mpp26", "mpp27";
+					marvell,function = "i2c1";
+				};
+
+				cf_gtr_sdhci_pins: cf-gtr-sdhci-pins {
+					marvell,pins = "mpp21", "mpp28",
+						       "mpp37", "mpp38",
+						       "mpp39", "mpp40";
+					marvell,function = "sd0";
+				};
+
+				cf_gtr_isolation_pins: cf-gtr-isolation-pins {
+					marvell,pins = "mpp47";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
+					marvell,pins = "mpp48";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_spi1_cs_pins: spi1-cs-pins {
+					marvell,pins = "mpp59";
+					marvell,function = "spi1";
+				};
+
+				cf_gtr_front_button_pins: cf-gtr-front-button-pins {
+					marvell,pins = "mpp53";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_rear_button_pins: cf-gtr-rear-button-pins {
+					marvell,pins = "mpp36";
+					marvell,function = "gpio";
+				};
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				no-1-8-v;
+				non-removable;
+				pinctrl-0 = <&cf_gtr_sdhci_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			usb@58000 {
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				vbus-supply = <&v_usb3_con>;
+				status = "okay";
+			};
+		};
+
+		pcie {
+			status = "okay";
+			/*
+			 * The PCIe units are accessible through
+			 * the mini-PCIe connectors on the board.
+			 */
+			pcie@1,0 {
+				reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+
+			pcie@3,0 {
+				reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+		};
+	};
+
+	sfp0: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>;
+		pinctrl-names = "default";
+
+		button-0 {
+			label = "Rear Button";
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_0>;
+		};
+
+		button-1 {
+			label = "Front Button";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_1>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			function = LED_FUNCTION_CPU;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led2 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&bm {
+	status = "okay";
+};
+
+&bm_bppi {
+	status = "okay";
+};
+
+&eth0 {
+	/* ethernet@70000 */
+	pinctrl-0 = <&ge0_rgmii_pins>;
+	pinctrl-names = "default";
+	phy = <&phy_dedicated>;
+	phy-mode = "rgmii-id";
+	buffer-manager = <&bm>;
+	bm,pool-long = <0>;
+	bm,pool-short = <1>;
+	status = "okay";
+};
+
+&eth1 {
+	/* ethernet@30000 */
+	bm,pool-long = <2>;
+	bm,pool-short = <1>;
+	buffer-manager = <&bm>;
+	phys = <&comphy1 1>;
+	phy-mode = "2500base-x";
+	status = "okay";
+
+	fixed-link {
+		speed = <2500>;
+		full-duplex;
+	};
+};
+
+&eth2 {
+	/* ethernet@34000 */
+	bm,pool-long = <3>;
+	bm,pool-short = <1>;
+	buffer-manager = <&bm>;
+	managed = "in-band-status";
+	phys = <&comphy5 1>;
+	phy-mode = "sgmii";
+	sfp = <&sfp0>;
+	status = "okay";
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+	status = "okay";
+
+	phy_dedicated: ethernet-phy@0 {
+		/*
+		 * Annoyingly, the marvell phy driver configures the LED
+		 * register, rather than preserving reset-loaded setting.
+		 * We undo that rubbish here.
+		 */
+		marvell,reg-init = <3 16 0 0x1017>;
+		reg = <0>;
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&spi1 {
+	/*
+	 * CS0: W25Q32 flash
+	 */
+	pinctrl-0 = <&spi1_pins &cf_gtr_spi1_cs_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "w25q32", "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <3000000>;
+		status = "okay";
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* U26 temperature sensor placed near SoC */
+	temp1: nct75@4c {
+		compatible = "lm75";
+		reg = <0x4c>;
+	};
+
+	/* U27 temperature sensor placed near RTC battery */
+	temp2: nct75@4d {
+		compatible = "lm75";
+		reg = <0x4d>;
+	};
+
+	/* 2Kb eeprom */
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+	};
+};
+
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&cf_gtr_fan_pwm>;
+	pinctrl-names = "default";
+
+	wifi-disable {
+		gpio-hog;
+		gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "wifi-disable";
+	};
+};
+
+&gpio1 {
+	pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins>;
+	pinctrl-names = "default";
+
+	lte-disable {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "lte-disable";
+	};
+
+	/*
+	 * This signal, when asserted, isolates Armada 38x sample at reset pins
+	 * from control of external devices. Should be de-asserted after reset.
+	 */
+	sar-isolation {
+		gpio-hog;
+		gpios = <15 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "sar-isolation";
+	};
+
+	poe-reset {
+		gpio-hog;
+		gpios = <16 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "poe-reset";
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts b/arch/arm/boot/dts/marvell/armada-385-db-88f6820-amc.dts
index 7881df3b28a0..389d9c75d546 100644
--- a/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-db-88f6820-amc.dts
@@ -126,7 +126,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/marvell/armada-385-db-ap.dts
index 0e4613bb56ee..332f8fce77dc 100644
--- a/arch/arm/boot/dts/armada-385-db-ap.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-db-ap.dts
@@ -192,7 +192,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-linksys-caiman.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-caiman.dts
index a03050c97084..88b2921fed55 100644
--- a/arch/arm/boot/dts/armada-385-linksys-caiman.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-caiman.dts
@@ -62,11 +62,11 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		label = "caiman:white:power";
 	};
 
-	sata {
+	led-sata {
 		label = "caiman:white:sata";
 	};
 };
diff --git a/arch/arm/boot/dts/armada-385-linksys-cobra.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-cobra.dts
index e3e4877a6f49..88200f930d0d 100644
--- a/arch/arm/boot/dts/armada-385-linksys-cobra.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-cobra.dts
@@ -62,11 +62,11 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		label = "cobra:white:power";
 	};
 
-	sata {
+	led-sata {
 		label = "cobra:white:sata";
 	};
 };
diff --git a/arch/arm/boot/dts/armada-385-linksys-rango.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-rango.dts
index 3c4af57ec2b9..4ab45f294de2 100644
--- a/arch/arm/boot/dts/armada-385-linksys-rango.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-rango.dts
@@ -54,22 +54,22 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
 		label = "rango:white:power";
 	};
 
-	sata {
+	led-sata {
 		gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		label = "rango:white:sata";
 	};
 
-	wlan_2g {
+	led-wlan_2g {
 		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
 		label = "rango:white:wlan_2g";
 	};
 
-	wlan_5g {
+	led-wlan_5g {
 		gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		label = "rango:white:wlan_5g";
 	};
diff --git a/arch/arm/boot/dts/armada-385-linksys-shelby.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-shelby.dts
index 3451cd3e5dff..f1b1f22413f1 100644
--- a/arch/arm/boot/dts/armada-385-linksys-shelby.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-shelby.dts
@@ -62,11 +62,11 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		label = "shelby:white:power";
 	};
 
-	sata {
+	led-sata {
 		label = "shelby:white:sata";
 	};
 };
diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
index 827e82be2201..4116ed60f709 100644
--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
@@ -53,13 +53,13 @@
 		pinctrl-0 = <&gpio_keys_pins>;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
@@ -71,12 +71,12 @@
 		pinctrl-0 = <&gpio_leds_pins>;
 		pinctrl-names = "default";
 
-		power {
+		led-power {
 			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		sata {
+		led-sata {
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "disk-activity";
@@ -148,6 +148,8 @@
 		reg = <0>;
 		label = "pxa3xx_nand-0";
 		nand-rb = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
 		marvell,nand-keep-config;
 		nand-on-flash-bbt;
 	};
@@ -156,44 +158,42 @@
 &mdio {
 	status = "okay";
 
-	switch@0 {
+	ethernet-switch@0 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan4";
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan3";
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan2";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan1";
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "wan";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "sgmii";
 				ethernet = <&eth2>;
 
 				fixed-link {
diff --git a/arch/arm/boot/dts/armada-385-synology-ds116.dts b/arch/arm/boot/dts/marvell/armada-385-synology-ds116.dts
index d8769956cbfc..6caa5c50175a 100644
--- a/arch/arm/boot/dts/armada-385-synology-ds116.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-synology-ds116.dts
@@ -131,14 +131,14 @@
 			gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>,
 				<&gpio1 17 GPIO_ACTIVE_HIGH>,
 				<&gpio1 16 GPIO_ACTIVE_HIGH>;
-			gpio-fan,speed-map = <   0 0
-					      1500 1
-					      2500 2
-					      3000 3
-					      3400 4
-					      3700 5
-					      3900 6
-					      4000 7>;
+			gpio-fan,speed-map = <   0 0>,
+					     <1500 1>,
+					     <2500 2>,
+					     <3000 3>,
+					     <3400 4>,
+					     <3700 5>,
+					     <3900 6>,
+					     <4000 7>;
 			#cooling-cells = <2>;
 		};
 
@@ -149,7 +149,7 @@
 			 * sata0, and accesses to SATA disk 0 make it blink so it
 			 * doesn't need to be declared here.
 			 */
-			orange {
+			led-orange {
 				gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 				label = "ds116:orange:disk";
 				default-state = "off";
@@ -223,7 +223,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "macronix,mx25l6405d", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts b/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
new file mode 100644
index 000000000000..7b755bb4e4e7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
@@ -0,0 +1,569 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for the Turris Omnia
+ *
+ * Copyright (C) 2016 Uwe Kleine-König <uwe@kleine-koenig.org>
+ * Copyright (C) 2016 Tomas Hlavacek <tmshlvkc@gmail.com>
+ *
+ * Schematic available at https://www.turris.cz/doc/_media/rtrom01-schema.pdf
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-385.dtsi"
+
+/ {
+	model = "Turris Omnia";
+	compatible = "cznic,turris-omnia", "marvell,armada385", "marvell,armada380";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1024 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+
+			/* USB part of the PCIe2/USB 2.0 port */
+			usb@58000 {
+				status = "okay";
+			};
+
+			sata@a8000 {
+				status = "okay";
+			};
+
+			sdhci@d8000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&sdhci_pins>;
+				status = "okay";
+
+				bus-width = <8>;
+				no-1-8-v;
+				non-removable;
+			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+			};
+		};
+
+		pcie {
+			status = "okay";
+
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+				slot-power-limit-milliwatt = <10000>;
+			};
+
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+				slot-power-limit-milliwatt = <10000>;
+			};
+
+			pcie@3,0 {
+				/* Port 2, Lane 0 */
+				status = "okay";
+				slot-power-limit-milliwatt = <10000>;
+			};
+		};
+	};
+
+	sfp: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&sfp_i2c>;
+		tx-fault-gpios = <&pcawan 0 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&pcawan 1 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&pcawan 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&pcawan 3 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pcawan 4 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <3000>;
+
+		/*
+		 * For now this has to be enabled at boot time by U-Boot when
+		 * a SFP module is present. Read more in the comment in the
+		 * eth2 node below.
+		 */
+		status = "disabled";
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,cpu {
+			sound-dai = <&audio_controller 1>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+};
+
+&audio_controller {
+	/* Pin header U16, GPIO51 in SPDIFO mode */
+	pinctrl-0 = <&spdif_pins>;
+	pinctrl-names = "default";
+	spdif-mode;
+	status = "okay";
+};
+
+&bm {
+	status = "okay";
+};
+
+&bm_bppi {
+	status = "okay";
+};
+
+/* Connected to 88E6176 switch, port 6 */
+&eth0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ge0_rgmii_pins>;
+	status = "okay";
+	phy-mode = "rgmii";
+	buffer-manager = <&bm>;
+	bm,pool-long = <0>;
+	bm,pool-short = <3>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+/* Connected to 88E6176 switch, port 5 */
+&eth1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ge1_rgmii_pins>;
+	status = "okay";
+	phy-mode = "rgmii";
+	buffer-manager = <&bm>;
+	bm,pool-long = <1>;
+	bm,pool-short = <3>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+/* WAN port */
+&eth2 {
+	/*
+	 * eth2 is connected via a multiplexor to both the SFP cage and to
+	 * ethernet-phy@1. The multiplexor switches the signal to SFP cage when
+	 * a SFP module is present, as determined by the mode-def0 GPIO.
+	 *
+	 * Until kernel supports this configuration properly, in case SFP module
+	 * is present, U-Boot has to enable the sfp node above, remove phy
+	 * handle and add managed = "in-band-status" property.
+	 */
+	status = "okay";
+	phy-mode = "sgmii";
+	phy-handle = <&phy1>;
+	phys = <&comphy5 2>;
+	sfp = <&sfp>;
+	buffer-manager = <&bm>;
+	bm,pool-long = <2>;
+	bm,pool-short = <3>;
+	label = "wan";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	i2cmux@70 {
+		compatible = "nxp,pca9547";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			/* STM32F0 command interface at address 0x2a */
+
+			led-controller@2b {
+				compatible = "cznic,turris-omnia-leds";
+				reg = <0x2b>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "okay";
+
+				/*
+				 * LEDs are controlled by MCU (STM32F0) at
+				 * address 0x2b.
+				 *
+				 * LED functions are not stable yet:
+				 * - there are 3 LEDs connected via MCU to PCIe
+				 *   ports. One of these ports supports mSATA.
+				 *   There is no mSATA nor PCIe function.
+				 *   For now we use LED_FUNCTION_WLAN, since
+				 *   in most cases users have wifi cards in
+				 *   these slots
+				 * - there are 2 LEDs dedicated for user: A and
+				 *   B. Again there is no such function defined.
+				 *   For now we use LED_FUNCTION_INDICATOR
+				 */
+
+				multi-led@0 {
+					reg = <0x0>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_INDICATOR;
+					function-enumerator = <2>;
+				};
+
+				multi-led@1 {
+					reg = <0x1>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_INDICATOR;
+					function-enumerator = <1>;
+				};
+
+				multi-led@2 {
+					reg = <0x2>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WLAN;
+					function-enumerator = <3>;
+				};
+
+				multi-led@3 {
+					reg = <0x3>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WLAN;
+					function-enumerator = <2>;
+				};
+
+				multi-led@4 {
+					reg = <0x4>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WLAN;
+					function-enumerator = <1>;
+				};
+
+				multi-led@5 {
+					reg = <0x5>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_WAN;
+				};
+
+				multi-led@6 {
+					reg = <0x6>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <4>;
+				};
+
+				multi-led@7 {
+					reg = <0x7>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <3>;
+				};
+
+				multi-led@8 {
+					reg = <0x8>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <2>;
+				};
+
+				multi-led@9 {
+					reg = <0x9>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <1>;
+				};
+
+				multi-led@a {
+					reg = <0xa>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_LAN;
+					function-enumerator = <0>;
+				};
+
+				multi-led@b {
+					reg = <0xb>;
+					color = <LED_COLOR_ID_RGB>;
+					function = LED_FUNCTION_POWER;
+				};
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+
+				/* The EEPROM contains data for bootloader.
+				 * Contents:
+				 * 	struct omnia_eeprom {
+				 * 		u32 magic; (=0x0341a034 in LE)
+				 *		u32 ramsize; (in GiB)
+				 * 		char regdomain[4];
+				 * 		u32 crc32;
+				 * 	};
+				 */
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			/* routed to PCIe0/mSATA connector (CN7A) */
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			/* routed to PCIe1/USB2 connector (CN61A) */
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			/* routed to PCIe2 connector (CN62A) */
+		};
+
+		sfp_i2c: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			/* routed to SFP+ */
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			/* ATSHA204A-MAHDA-T crypto module */
+			crypto@64 {
+				compatible = "atmel,atsha204a";
+				reg = <0x64>;
+			};
+		};
+
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			/* exposed on pin header */
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			pcawan: gpio@71 {
+				/*
+				 * GPIO expander for SFP+ signals and
+				 * and phy irq
+				 */
+				compatible = "nxp,pca9538";
+				reg = <0x71>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&pcawan_pins>;
+
+				interrupt-parent = <&gpio1>;
+				interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		marvell,reg-init = <3 18 0 0x4985>,
+				   <3 16 0xfff0 0x0001>;
+
+		/* irq is connected to &pcawan pin 7 */
+	};
+
+	/* Switch MV88E6176 at address 0x10 */
+	ethernet-switch@10 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&swint_pins>;
+		compatible = "marvell,mv88e6085";
+
+		dsa,member = <0 0>;
+		reg = <0x10>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet-port@0 {
+				reg = <0>;
+				label = "lan0";
+			};
+
+			ethernet-port@1 {
+				reg = <1>;
+				label = "lan1";
+			};
+
+			ethernet-port@2 {
+				reg = <2>;
+				label = "lan2";
+			};
+
+			ethernet-port@3 {
+				reg = <3>;
+				label = "lan3";
+			};
+
+			ethernet-port@4 {
+				reg = <4>;
+				label = "lan4";
+			};
+
+			ethernet-port@5 {
+				reg = <5>;
+				ethernet = <&eth1>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet-port@6 {
+				reg = <6>;
+				ethernet = <&eth0>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pcawan_pins: pcawan-pins {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	swint_pins: swint-pins {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	spi0cs0_pins: spi0cs0-pins {
+		marvell,pins = "mpp25";
+		marvell,function = "spi0";
+	};
+
+	spi0cs2_pins: spi0cs2-pins {
+		marvell,pins = "mpp26";
+		marvell,function = "spi0";
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0cs0_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spansion,s25fl164k", "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				reg = <0x0 0x00100000>;
+				label = "U-Boot";
+			};
+
+			partition@100000 {
+				reg = <0x00100000 0x00700000>;
+				label = "Rescue system";
+			};
+		};
+	};
+
+	/* MISO, MOSI, SCLK and CS2 are routed to pin header CN11 */
+};
+
+&uart0 {
+	/* Pin header CN10 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	/* Pin header CN11 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/marvell/armada-385.dtsi
index f0022d10c715..be8d607c59b2 100644
--- a/arch/arm/boot/dts/armada-385.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-385.dtsi
@@ -69,54 +69,81 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/*
@@ -125,20 +152,29 @@
 			 */
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x48000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/armada-388-clearfog-base.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
index 53b4bd35522a..f7daa3bc707e 100644
--- a/arch/arm/boot/dts/armada-388-clearfog-base.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
@@ -19,7 +19,7 @@
 		pinctrl-0 = <&rear_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear SW3 button */
 			label = "Rear Button";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-388-clearfog-pro.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog-pro.dts
index ff890c09c3ed..ff890c09c3ed 100644
--- a/arch/arm/boot/dts/armada-388-clearfog-pro.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog-pro.dts
diff --git a/arch/arm/boot/dts/armada-388-clearfog.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
index 20f8d4667753..3290ccad2374 100644
--- a/arch/arm/boot/dts/armada-388-clearfog.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
@@ -35,7 +35,7 @@
 		pinctrl-0 = <&rear_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear SW3 button */
 			label = "Rear Button";
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
@@ -47,6 +47,8 @@
 
 &eth1 {
 	/* ethernet@30000 */
+	phy-mode = "1000base-x";
+
 	fixed-link {
 		speed = <1000>;
 		full-duplex;
@@ -73,13 +75,13 @@
 	 * 14-SFP_TX_DISABLE
 	 * 15-SFP_MOD_DEF0
 	 */
-	pcie2_0_clkreq {
+	pcie2-0-clkreq-hog {
 		gpio-hog;
 		gpios = <4 GPIO_ACTIVE_LOW>;
 		input;
 		line-name = "pcie2.0-clkreq";
 	};
-	pcie2_0_w_disable {
+	pcie2-0-w-disable-hog {
 		gpio-hog;
 		gpios = <7 GPIO_ACTIVE_LOW>;
 		output-low;
@@ -90,57 +92,58 @@
 &mdio {
 	status = "okay";
 
-	switch@4 {
+	ethernet-switch@4 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <4>;
 		pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
 		pinctrl-names = "default";
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan5";
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan4";
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan3";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan2";
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "lan1";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
 				ethernet = <&eth1>;
+				phy-mode = "1000base-x";
+
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
 				};
 			};
 
-			port@6 {
+			ethernet-port@6 {
 				/* 88E1512 external phy */
 				reg = <6>;
 				label = "lan6";
+				phy-mode = "rgmii-id";
+
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
diff --git a/arch/arm/boot/dts/armada-388-clearfog.dtsi b/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
index 0d81600ca247..f8a06ae4a3c9 100644
--- a/arch/arm/boot/dts/armada-388-clearfog.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
@@ -111,11 +111,6 @@
 };
 
 &i2c0 {
-	clock-frequency = <400000>;
-	pinctrl-0 = <&i2c0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
 	/*
 	 * PCA9655 GPIO expander, up to 1MHz clock.
 	 *  0-CON3 CLKREQ#
@@ -146,31 +141,31 @@
 		#gpio-cells = <2>;
 		reg = <0x20>;
 
-		pcie1_0_clkreq {
+		pcie1-0-clkreq-hog {
 			gpio-hog;
 			gpios = <0 GPIO_ACTIVE_LOW>;
 			input;
 			line-name = "pcie1.0-clkreq";
 		};
-		pcie1_0_w_disable {
+		pcie1-0-w-disable-hog {
 			gpio-hog;
 			gpios = <3 GPIO_ACTIVE_LOW>;
 			output-low;
 			line-name = "pcie1.0-w-disable";
 		};
-		usb3_ilimit {
+		usb3-ilimit-hog {
 			gpio-hog;
 			gpios = <5 GPIO_ACTIVE_LOW>;
 			input;
 			line-name = "usb3-current-limit";
 		};
-		usb3_power {
+		usb3-power-hog {
 			gpio-hog;
 			gpios = <6 GPIO_ACTIVE_HIGH>;
 			output-high;
 			line-name = "usb3-power";
 		};
-		m2_devslp {
+		m2-devslp-hog {
 			gpio-hog;
 			gpios = <11 GPIO_ACTIVE_HIGH>;
 			output-low;
@@ -183,6 +178,12 @@
 		compatible = "microchip,mcp3021";
 		reg = <0x4c>;
 	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
 };
 
 &i2c1 {
diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/marvell/armada-388-db.dts
index a2bec07bf4c5..45cc784659fd 100644
--- a/arch/arm/boot/dts/armada-388-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-db.dts
@@ -36,6 +36,11 @@
 			i2c@11000 {
 				status = "okay";
 				clock-frequency = <100000>;
+				audio_codec: audio-codec@4a {
+					#sound-dai-cells = <0>;
+					compatible = "cirrus,cs42l51";
+					reg = <0x4a>;
+				};
 			};
 
 			i2c@11100 {
@@ -57,7 +62,7 @@
 			};
 
 			usb@58000 {
-				status = "ok";
+				status = "okay";
 			};
 
 			ethernet@70000 {
@@ -99,6 +104,12 @@
 				no-1-8-v;
 			};
 
+			audio-controller@e8000 {
+				pinctrl-0 = <&i2s_pins>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
 			usb3@f0000 {
 				status = "okay";
 			};
@@ -128,12 +139,70 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "Armada 385 DB Audio";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Headphone", "Out Jack",
+			"Line", "In Jack";
+		simple-audio-card,routing =
+			"Out Jack", "HPL",
+			"Out Jack", "HPR",
+			"AIN1L", "In Jack",
+			"AIN1R", "In Jack";
+		status = "disabled";
+
+		simple-audio-card,dai-link@0 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 0>;
+			};
+
+			codec {
+				sound-dai = <&audio_codec>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_out>;
+			};
+		};
+
+		simple-audio-card,dai-link@2 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_in>;
+			};
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
+	spdif_in: spdif-in {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dir";
+	};
 };
 
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/marvell/armada-388-gp.dts
index 9d873257ac45..1de0a172aa5f 100644
--- a/arch/arm/boot/dts/armada-388-gp.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-gp.dts
@@ -237,8 +237,8 @@
 		gpio-fan {
 			compatible = "gpio-fan";
 			gpios = <&expander1 3 GPIO_ACTIVE_HIGH>;
-			gpio-fan,speed-map = <	 0 0
-					      3000 1>;
+			gpio-fan,speed-map = <	 0 0>,
+					     <3000 1>;
 		};
 	};
 
@@ -395,7 +395,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/marvell/armada-388-helios4.dts
index 705adfa8c680..ec134e22bae3 100644
--- a/arch/arm/boot/dts/armada-388-helios4.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-helios4.dts
@@ -70,6 +70,9 @@
 
 	system-leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_system_led_pins>;
+
 		status-led {
 			label = "helios4:green:status";
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
@@ -86,6 +89,9 @@
 
 	io-leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_io_led_pins>;
+
 		sata1-led {
 			label = "helios4:green:ata1";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
@@ -121,11 +127,15 @@
 	fan1: j10-pwm {
 		compatible = "pwm-fan";
 		pwms = <&gpio1 9 40000>;	/* Target freq:25 kHz */
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_fan1_pins>;
 	};
 
 	fan2: j17-pwm {
 		compatible = "pwm-fan";
 		pwms = <&gpio1 23 40000>;	/* Target freq:25 kHz */
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_fan2_pins>;
 	};
 
 	usb2_phy: usb2-phy {
@@ -140,11 +150,6 @@
 	soc {
 		internal-regs {
 			i2c@11000 {
-				clock-frequency = <400000>;
-				pinctrl-0 = <&i2c0_pins>;
-				pinctrl-names = "default";
-				status = "okay";
-
 				/*
 				 * PCA9655 GPIO expander, up to 1MHz clock.
 				 *  0-Board Revision bit 0 #
@@ -171,19 +176,19 @@
 					interrupt-controller;
 					#interrupt-cells = <2>;
 
-					board_rev_bit_0 {
+					board-rev-bit-0-hog {
 						gpio-hog;
 						gpios = <0 GPIO_ACTIVE_LOW>;
 						input;
 						line-name = "board-rev-0";
 					};
-					board_rev_bit_1 {
+					board-rev-bit-1-hog {
 						gpio-hog;
 						gpios = <1 GPIO_ACTIVE_LOW>;
 						input;
 						line-name = "board-rev-1";
 					};
-					usb3_ilimit {
+					usb3-ilimit-hog {
 						gpio-hog;
 						gpios = <5 GPIO_ACTIVE_HIGH>;
 						input;
@@ -291,16 +296,22 @@
 						       "mpp39", "mpp40";
 					marvell,function = "sd0";
 				};
-				helios_led_pins: helios-led-pins {
-					marvell,pins = "mpp24", "mpp25",
-						       "mpp49", "mpp50",
+				helios_system_led_pins: helios-system-led-pins {
+					marvell,pins = "mpp24", "mpp25";
+					marvell,function = "gpio";
+				};
+				helios_io_led_pins: helios-io-led-pins {
+					marvell,pins = "mpp49", "mpp50",
 						       "mpp52", "mpp53",
 						       "mpp54";
 					marvell,function = "gpio";
 				};
-				helios_fan_pins: helios-fan-pins {
-					marvell,pins = "mpp41", "mpp43",
-						       "mpp48", "mpp55";
+				helios_fan1_pins: helios_fan1_pins {
+					marvell,pins = "mpp41", "mpp43";
+					marvell,function = "gpio";
+				};
+				helios_fan2_pins: helios_fan2_pins {
+					marvell,pins = "mpp48", "mpp55";
 					marvell,function = "gpio";
 				};
 				microsom_spi1_cs_pins: spi1-cs-pins {
diff --git a/arch/arm/boot/dts/armada-388-rd.dts b/arch/arm/boot/dts/marvell/armada-388-rd.dts
index 328a4d6afd2c..c0efafd45b33 100644
--- a/arch/arm/boot/dts/armada-388-rd.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-rd.dts
@@ -97,7 +97,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388.dtsi b/arch/arm/boot/dts/marvell/armada-388.dtsi
index f3a020ff577e..f3a020ff577e 100644
--- a/arch/arm/boot/dts/armada-388.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-388.dtsi
diff --git a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/boot/dts/marvell/armada-38x-solidrun-microsom.dtsi
index 3a7f9c1ac346..2c64bc6e5a17 100644
--- a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-38x-solidrun-microsom.dtsi
@@ -71,6 +71,19 @@
 	};
 };
 
+&i2c0 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
 &pinctrl {
 	microsom_phy_clk_pins: microsom-phy-clk-pins {
 		marvell,pins = "mpp45";
@@ -88,7 +101,7 @@
 	/* The microsom has an optional W25Q32 on board, connected to CS0 */
 	pinctrl-0 = <&spi1_pins>;
 
-	w25q32: spi-flash@0 {
+	w25q32: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/marvell/armada-38x.dtsi
index e038abc0c6b4..446861b6b17b 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-38x.dtsi
@@ -153,7 +153,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -164,13 +163,12 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
 
 			uart0: serial@12000 {
-				compatible = "marvell,armada-38x-uart";
+				compatible = "marvell,armada-38x-uart", "ns16550a";
 				reg = <0x12000 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
@@ -180,7 +178,7 @@
 			};
 
 			uart1: serial@12100 {
-				compatible = "marvell,armada-38x-uart";
+				compatible = "marvell,armada-38x-uart", "ns16550a";
 				reg = <0x12100 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
@@ -291,6 +289,18 @@
 					marvell,pins = "mpp44";
 					marvell,function = "sata3";
 				};
+
+				i2s_pins: i2s-pins {
+					marvell,pins = "mpp48", "mpp49",
+						       "mpp50", "mpp51",
+						       "mpp52", "mpp53";
+					marvell,function = "audio";
+				};
+
+				spdif_pins: spdif-pins {
+					marvell,pins = "mpp51";
+					marvell,function = "audio";
+				};
 			};
 
 			gpio0: gpio@18100 {
@@ -300,6 +310,7 @@
 				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
+				gpio-ranges = <&pinctrl 0 0 32>;
 				#gpio-cells = <2>;
 				#pwm-cells = <2>;
 				interrupt-controller;
@@ -318,6 +329,7 @@
 				reg-names = "gpio", "pwm";
 				ngpios = <28>;
 				gpio-controller;
+				gpio-ranges = <&pinctrl 0 32 28>;
 				#gpio-cells = <2>;
 				#pwm-cells = <2>;
 				interrupt-controller;
@@ -344,7 +356,8 @@
 
 			comphy: phy@18300 {
 				compatible = "marvell,armada-380-comphy";
-				reg = <0x18300 0x100>;
+				reg-names = "comphy", "conf";
+				reg = <0x18300 0x100>, <0x18460 4>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -619,6 +632,18 @@
 				status = "disabled";
 			};
 
+			audio_controller: audio-controller@e8000 {
+				#sound-dai-cells = <1>;
+				compatible = "marvell,armada-380-audio";
+				reg = <0xe8000 0x4000>, <0x18410 0xc>,
+				      <0x18204 0x4>;
+				reg-names = "i2s_regs", "pll_regs", "soc_ctrl";
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 0>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+
 			usb3_0: usb3@f0000 {
 				compatible = "marvell,armada-380-xhci";
 				reg = <0xf0000 0x4000>,<0xf4000 0x4000>;
diff --git a/arch/arm/boot/dts/armada-390-db.dts b/arch/arm/boot/dts/marvell/armada-390-db.dts
index 0e29474ae9a2..20f518dbac97 100644
--- a/arch/arm/boot/dts/armada-390-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-390-db.dts
@@ -81,7 +81,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@1 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13",
diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/marvell/armada-390.dtsi
index aa2057d4d6f8..aa2057d4d6f8 100644
--- a/arch/arm/boot/dts/armada-390.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-390.dtsi
diff --git a/arch/arm/boot/dts/armada-395-gp.dts b/arch/arm/boot/dts/marvell/armada-395-gp.dts
index 6dd9e9077f84..6dd9e9077f84 100644
--- a/arch/arm/boot/dts/armada-395-gp.dts
+++ b/arch/arm/boot/dts/marvell/armada-395-gp.dts
diff --git a/arch/arm/boot/dts/armada-395.dtsi b/arch/arm/boot/dts/marvell/armada-395.dtsi
index e18a7d9cd7d4..e18a7d9cd7d4 100644
--- a/arch/arm/boot/dts/armada-395.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-395.dtsi
diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/marvell/armada-398-db.dts
index fc28308e5bc5..ec6cdbeedde7 100644
--- a/arch/arm/boot/dts/armada-398-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-398-db.dts
@@ -79,7 +79,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/marvell/armada-398.dtsi
index c5ac89399ce1..c5ac89399ce1 100644
--- a/arch/arm/boot/dts/armada-398.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-398.dtsi
diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/marvell/armada-39x.dtsi
index b1b86934c688..9d1cac49c022 100644
--- a/arch/arm/boot/dts/armada-39x.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-39x.dtsi
@@ -108,7 +108,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -119,7 +118,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -130,7 +128,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -141,7 +138,6 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
-				timeout-ms = <1000>;
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
@@ -442,54 +438,84 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/*
@@ -498,20 +524,30 @@
 			 */
 			pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x48000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/marvell/armada-xp-98dx3236.dtsi
index 654648b05c7c..7a7e2066c498 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-98dx3236.dtsi
@@ -76,16 +76,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
@@ -264,11 +274,8 @@
 &i2c0 {
 	compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
 	reg = <0x11000 0x100>;
-};
-
-&i2c1 {
-	compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
-	reg = <0x11100 0x100>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
 };
 
 &mpic {
@@ -289,6 +296,7 @@
 	compatible = "marvell,armada-xp-wdt";
 	clocks = <&coreclk 2>, <&refclk>;
 	clock-names = "nbclk", "fixed";
+	interrupts = <93>, <38>;
 };
 
 &cpurst {
@@ -324,6 +332,11 @@
 			       "mpp2", "mpp3";
 		marvell,function = "spi0";
 	};
+
+	i2c0_pins: i2c-pins-0 {
+		marvell,pins = "mpp14", "mpp15";
+		marvell,function = "i2c0";
+	};
 };
 
 &spi0 {
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/marvell/armada-xp-98dx3336.dtsi
index 1d9d8a8ea60c..1d9d8a8ea60c 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-98dx3336.dtsi
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/marvell/armada-xp-98dx4251.dtsi
index 48ffdc72bfc7..48ffdc72bfc7 100644
--- a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-98dx4251.dtsi
diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/marvell/armada-xp-axpwifiap.dts
index 606fd3476a59..5a74197be0ad 100644
--- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-axpwifiap.dts
@@ -69,14 +69,12 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_SETUP>;
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -134,7 +132,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s-bit.dts b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s-bit.dts
new file mode 100644
index 000000000000..c28e140b4afc
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s-bit.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for MikroTik CRS305-1G-4S+ Bit board
+ *
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ */
+
+#include "armada-xp-crs305-1g-4s.dtsi"
+
+/ {
+	model = "MikroTik CRS305-1G-4S+ Bit";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <108000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x001f0000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x001f0000 0x00010000>;
+			label = "u-boot-env";
+		};
+		partition@ubi1 {
+			reg = <0x00200000 0x03f00000>;
+			label = "ubi1";
+		};
+		partition@ubi2 {
+			reg = <0x04100000 0x03f00000>;
+			label = "ubi2";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dts b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dts
new file mode 100644
index 000000000000..010b83b54212
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for MikroTik CRS305-1G-4S+ board
+ *
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ */
+
+#include "armada-xp-crs305-1g-4s.dtsi"
+
+/ {
+	model = "MikroTik CRS305-1G-4S+";
+};
+
+&spi0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dtsi b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dtsi
new file mode 100644
index 000000000000..47b003a81bd4
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dtsi
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CRS305-1G-4S board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ * Copyright (C) 2020 Sartura Ltd.
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+	model = "CRS305-1G-4S+";
+	compatible = "mikrotik,crs305-1g-4s", "marvell,armadaxp-98dx3236", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+	};
+};
+
+&L2 {
+	arm,parity-enable;
+	marvell,ecc-enable;
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	/* Device Bus parameters are required */
+
+	/* Read parameters */
+	devbus,bus-width    = <16>;
+	devbus,turn-off-ps  = <60000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <124000>;
+	devbus,acc-next-ps  = <248000>;
+	devbus,rd-setup-ps  = <0>;
+	devbus,rd-hold-ps   = <0>;
+
+	/* Write parameters */
+	devbus,sync-enable = <0>;
+	devbus,wr-high-ps  = <60000>;
+	devbus,wr-low-ps   = <60000>;
+	devbus,ale-wr-ps   = <60000>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <108000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x001f0000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x001f0000 0x00010000>;
+			label = "u-boot-env";
+		};
+		partition@ubi1 {
+			reg = <0x00200000 0x00e00000>;
+			label = "ubi1";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s-bit.dts b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s-bit.dts
new file mode 100644
index 000000000000..20ba5c823bb2
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s-bit.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for MikroTik CRS326-24G-2S+ Bit board
+ *
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ */
+
+#include "armada-xp-crs326-24g-2s.dtsi"
+
+/ {
+	model = "MikroTik CRS326-24G-2S+ Bit";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <108000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x001f0000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x001f0000 0x00010000>;
+			label = "u-boot-env";
+		};
+		partition@ubi1 {
+			reg = <0x00200000 0x03f00000>;
+			label = "ubi1";
+		};
+		partition@ubi2 {
+			reg = <0x04100000 0x03f00000>;
+			label = "ubi2";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dts b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dts
new file mode 100644
index 000000000000..83aef43f66d5
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for MikroTik CRS326-24G-2S+ board
+ *
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ */
+
+#include "armada-xp-crs326-24g-2s.dtsi"
+
+/ {
+	model = "MikroTik CRS326-24G-2S+";
+};
+
+&spi0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dtsi b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dtsi
new file mode 100644
index 000000000000..cab99d8e2911
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dtsi
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CRS326-24G-2S board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ * Copyright (C) 2020 Sartura Ltd.
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+	model = "CRS326-24G-2S+";
+	compatible = "mikrotik,crs326-24g-2s", "marvell,armadaxp-98dx3236", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+	};
+};
+
+&L2 {
+	arm,parity-enable;
+	marvell,ecc-enable;
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	/* Device Bus parameters are required */
+
+	/* Read parameters */
+	devbus,bus-width    = <16>;
+	devbus,turn-off-ps  = <60000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <124000>;
+	devbus,acc-next-ps  = <248000>;
+	devbus,rd-setup-ps  = <0>;
+	devbus,rd-hold-ps   = <0>;
+
+	/* Write parameters */
+	devbus,sync-enable = <0>;
+	devbus,wr-high-ps  = <60000>;
+	devbus,wr-low-ps   = <60000>;
+	devbus,ale-wr-ps   = <60000>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <108000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x001f0000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x001f0000 0x00010000>;
+			label = "u-boot-env";
+		};
+		partition@ubi1 {
+			reg = <0x00200000 0x00e00000>;
+			label = "ubi1";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s-bit.dts b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s-bit.dts
new file mode 100644
index 000000000000..2caa3980fdf6
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s-bit.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for MikroTik CRS328-4C-20S-4S+ Bit board
+ *
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ */
+
+#include "armada-xp-crs328-4c-20s-4s.dtsi"
+
+/ {
+	model = "MikroTik CRS328-4C-20S-4S+ Bit";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <108000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x001f0000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x001f0000 0x00010000>;
+			label = "u-boot-env";
+		};
+		partition@ubi1 {
+			reg = <0x00200000 0x03f00000>;
+			label = "ubi1";
+		};
+		partition@ubi2 {
+			reg = <0x04100000 0x03f00000>;
+			label = "ubi2";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dts b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dts
new file mode 100644
index 000000000000..665757f6e18e
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for MikroTik CRS328-4C-20S-4S+ board
+ *
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ */
+
+#include "armada-xp-crs328-4c-20s-4s.dtsi"
+
+/ {
+	model = "MikroTik CRS328-4C-20S-4S+";
+};
+
+&spi0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dtsi b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dtsi
new file mode 100644
index 000000000000..7028482ce4b2
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dtsi
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CRS328-4C-20S-4S+ board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ * Copyright (C) 2020 Sartura Ltd.
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+	model = "CRS328-4C-20S-4S+";
+	compatible = "mikrotik,crs328-4c-20s-4s", "marvell,armadaxp-98dx3236", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+	};
+};
+
+&L2 {
+	arm,parity-enable;
+	marvell,ecc-enable;
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	/* Device Bus parameters are required */
+
+	/* Read parameters */
+	devbus,bus-width    = <16>;
+	devbus,turn-off-ps  = <60000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <124000>;
+	devbus,acc-next-ps  = <248000>;
+	devbus,rd-setup-ps  = <0>;
+	devbus,rd-hold-ps   = <0>;
+
+	/* Write parameters */
+	devbus,sync-enable = <0>;
+	devbus,wr-high-ps  = <60000>;
+	devbus,wr-low-ps   = <60000>;
+	devbus,ale-wr-ps   = <60000>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <108000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x001f0000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x001f0000 0x00010000>;
+			label = "u-boot-env";
+		};
+		partition@ubi1 {
+			reg = <0x00200000 0x00e00000>;
+			label = "ubi1";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts b/arch/arm/boot/dts/marvell/armada-xp-db-dxbc2.dts
index 8a3aa616bbd0..02bef8dc4270 100644
--- a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-db-dxbc2.dts
@@ -93,7 +93,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64";
diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/marvell/armada-xp-db-xc3-24g4xg.dts
index 4ec0ae01b61d..d1b61dad0c46 100644
--- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-db-xc3-24g4xg.dts
@@ -89,7 +89,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/marvell/armada-xp-db.dts
index 5d04dc68cf57..75318fd0fc11 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-db.dts
@@ -235,7 +235,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/marvell/armada-xp-gp.dts
index b4cca507cf13..d1d348b91c0a 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-gp.dts
@@ -220,7 +220,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/marvell/armada-xp-lenovo-ix4-300d.dts
index 87dcb502f72d..21b95578fe95 100644
--- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-lenovo-ix4-300d.dts
@@ -164,11 +164,11 @@
 		};
 	};
 
-	spi3 {
+	spi-3 {
 		compatible = "spi-gpio";
 		status = "okay";
-		gpio-sck = <&gpio0 25 GPIO_ACTIVE_LOW>;
-		gpio-mosi = <&gpio1 15 GPIO_ACTIVE_LOW>; /*gpio 47*/
+		sck-gpios  = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		mosi-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; /*gpio 47*/
 		cs-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
index 8480a16919a0..ea859f7ea042 100644
--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
@@ -172,20 +172,18 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -197,7 +195,7 @@
 		pinctrl-0 = <&power_led_pin>;
 		pinctrl-names = "default";
 
-		power {
+		led-power {
 			label = "mamba:white:power";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -255,7 +253,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "everspin,mr25h256";
@@ -267,44 +265,42 @@
 &mdio {
 	status = "okay";
 
-	switch@0 {
+	ethernet-switch@0 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan4";
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan3";
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan2";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan1";
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "internet";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0>;
 				fixed-link {
 					speed = <1000>;
diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/marvell/armada-xp-matrix.dts
index 1395cea12759..1395cea12759 100644
--- a/arch/arm/boot/dts/armada-xp-matrix.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-matrix.dts
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/marvell/armada-xp-mv78230.dtsi
index 8558bf6bb54c..5ea9d509cd30 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-mv78230.dtsi
@@ -83,88 +83,138 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/marvell/armada-xp-mv78260.dtsi
index 2d85fe8ac327..6c6fbb9faf5a 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-mv78260.dtsi
@@ -98,160 +98,250 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie6: pcie@6,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+				assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 63>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
 					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie6_intc 0>,
+						<0 0 0 2 &pcie6_intc 1>,
+						<0 0 0 3 &pcie6_intc 2>,
+						<0 0 0 4 &pcie6_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 10>;
 				status = "disabled";
+
+				pcie6_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie7: pcie@7,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+				assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 64>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
 					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie7_intc 0>,
+						<0 0 0 2 &pcie7_intc 1>,
+						<0 0 0 3 &pcie7_intc 2>,
+						<0 0 0 4 &pcie7_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 11>;
 				status = "disabled";
+
+				pcie7_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie8: pcie@8,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+				assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 65>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
 					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie8_intc 0>,
+						<0 0 0 2 &pcie8_intc 1>,
+						<0 0 0 3 &pcie8_intc 2>,
+						<0 0 0 4 &pcie8_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 12>;
 				status = "disabled";
+
+				pcie8_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie9: pcie@9,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 99>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
 					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie9_intc 0>,
+						<0 0 0 2 &pcie9_intc 1>,
+						<0 0 0 3 &pcie9_intc 2>,
+						<0 0 0 4 &pcie9_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 26>;
 				status = "disabled";
+
+				pcie9_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/marvell/armada-xp-mv78460.dtsi
index 230a3fd36b30..16185edf9aa5 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-mv78460.dtsi
@@ -119,16 +119,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -137,16 +147,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
@@ -155,16 +175,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
@@ -173,16 +203,26 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
@@ -191,16 +231,26 @@
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie6: pcie@6,0 {
@@ -209,16 +259,26 @@
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 63>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
 					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie6_intc 0>,
+						<0 0 0 2 &pcie6_intc 1>,
+						<0 0 0 3 &pcie6_intc 2>,
+						<0 0 0 4 &pcie6_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 10>;
 				status = "disabled";
+
+				pcie6_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie7: pcie@7,0 {
@@ -227,16 +287,26 @@
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 64>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
 					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie7_intc 0>,
+						<0 0 0 2 &pcie7_intc 1>,
+						<0 0 0 3 &pcie7_intc 2>,
+						<0 0 0 4 &pcie7_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 11>;
 				status = "disabled";
+
+				pcie7_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie8: pcie@8,0 {
@@ -245,16 +315,26 @@
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 65>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
 					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie8_intc 0>,
+						<0 0 0 2 &pcie8_intc 1>,
+						<0 0 0 3 &pcie8_intc 2>,
+						<0 0 0 4 &pcie8_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 12>;
 				status = "disabled";
+
+				pcie8_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie9: pcie@9,0 {
@@ -263,16 +343,26 @@
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 99>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
 					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie9_intc 0>,
+						<0 0 0 2 &pcie9_intc 1>,
+						<0 0 0 3 &pcie9_intc 2>,
+						<0 0 0 4 &pcie9_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 26>;
 				status = "disabled";
+
+				pcie9_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie10: pcie@a,0 {
@@ -281,16 +371,26 @@
 				reg = <0x5000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 103>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
 					  0x81000000 0 0 0x81000000 0xa 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie10_intc 0>,
+						<0 0 0 2 &pcie10_intc 1>,
+						<0 0 0 3 &pcie10_intc 2>,
+						<0 0 0 4 &pcie10_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 27>;
 				status = "disabled";
+
+				pcie10_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/marvell/armada-xp-netgear-rn2120.dts
index 8ea73587db81..31933f81144e 100644
--- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-netgear-rn2120.dts
@@ -121,11 +121,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <32768>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/marvell/armada-xp-openblocks-ax3-4.dts
index 0efcc166dabf..1ecf72a61bca 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-openblocks-ax3-4.dts
@@ -97,12 +97,10 @@
 				};
 			};
 
-			gpio_keys {
+			gpio-keys {
 				compatible = "gpio-keys";
-				#address-cells = <1>;
-				#size-cells = <0>;
 
-				init {
+				button-init {
 					label = "Init Button";
 					linux,code = <KEY_POWER>;
 					gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/marvell/armada-xp-synology-ds414.dts
index 809e821d7399..1b65059794bf 100644
--- a/arch/arm/boot/dts/armada-xp-synology-ds414.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-synology-ds414.dts
@@ -109,65 +109,60 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
-			     &sata3_pwr_pin &sata4_pwr_pin>;
+	sata1_regulator: sata1-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <2000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata1_pwr_pin>;
 		pinctrl-names = "default";
+	};
 
-		sata1_regulator: sata1-regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA1 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <2000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		};
-
-		sata2_regulator: sata2-regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA2 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <4000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		};
+	sata2_regulator: sata2-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA2 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <4000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata2_pwr_pin>;
+		pinctrl-names = "default";
+	};
 
-		sata3_regulator: sata3-regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "SATA3 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <6000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
-		};
+	sata3_regulator: sata3-regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA3 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <6000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata3_pwr_pin>;
+		pinctrl-names = "default";
+	};
 
-		sata4_regulator: sata4-regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "SATA4 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <8000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
-		};
+	sata4_regulator: sata4-regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA4 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <8000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata4_pwr_pin>;
+		pinctrl-names = "default";
 	};
 };
 
@@ -274,7 +269,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q064", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/marvell/armada-xp.dtsi
index 6c19984d668e..4297482da62f 100644
--- a/arch/arm/boot/dts/armada-xp.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp.dtsi
@@ -260,6 +260,7 @@
 	compatible = "marvell,armada-xp-wdt";
 	clocks = <&coreclk 2>, <&refclk>;
 	clock-names = "nbclk", "fixed";
+	interrupts = <93>, <38>;
 };
 
 &cpurst {
diff --git a/arch/arm/boot/dts/dove-cm-a510.dtsi b/arch/arm/boot/dts/marvell/dove-cm-a510.dtsi
index 9b9dfbe07be4..621cb145a8f6 100644
--- a/arch/arm/boot/dts/dove-cm-a510.dtsi
+++ b/arch/arm/boot/dts/marvell/dove-cm-a510.dtsi
@@ -101,32 +101,34 @@
 		pinctrl-0 = <&pmx_nand_gpo>;
 		pinctrl-names = "default";
 
-		system {
+		led-system {
 			label = "cm-a510:system:green";
 			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		wifi_power: regulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "WiFi Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>;
-		};
+	wifi_power: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "WiFi Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>;
 	};
 };
 
 /* Optional RTL8211D GbE PHY on SMI address 0x03 */
-&ethphy {
-	reg = <3>;
-	status = "disabled";
+&mdio {
+	ethphy: ethernet-phy@3 {
+		reg = <3>;
+		status = "disabled";
+	};
+};
+
+&eth {
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
 };
 
 &i2c0 {
diff --git a/arch/arm/boot/dts/dove-cubox-es.dts b/arch/arm/boot/dts/marvell/dove-cubox-es.dts
index ad361ec1361d..ad361ec1361d 100644
--- a/arch/arm/boot/dts/dove-cubox-es.dts
+++ b/arch/arm/boot/dts/marvell/dove-cubox-es.dts
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/marvell/dove-cubox.dts
index 3e1584e787ae..bfde99486a87 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/marvell/dove-cubox.dts
@@ -21,31 +21,24 @@
 		pinctrl-0 = <&pmx_gpio_18>;
 		pinctrl-names = "default";
 
-		power {
+		led-power {
 			label = "Power";
 			gpios = <&gpio0 18 1>;
 			default-state = "keep";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 1 0>;
-			pinctrl-0 = <&pmx_gpio_1>;
-			pinctrl-names = "default";
-		};
+	usb_power: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio0 1 0>;
+		pinctrl-0 = <&pmx_gpio_1>;
+		pinctrl-names = "default";
 	};
 
 	clocks {
@@ -72,11 +65,18 @@
 &uart0 { status = "okay"; };
 &sata0 { status = "okay"; };
 &mdio { status = "okay"; };
-&eth { status = "okay"; };
+&eth {
+	status = "okay";
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
 
-&ethphy {
-	compatible = "marvell,88e1310";
-	reg = <1>;
+&mdio {
+	ethphy: ethernet-phy@1 {
+		compatible = "marvell,88e1310";
+		reg = <1>;
+	};
 };
 
 &gpu {
@@ -127,7 +127,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Winbond W25Q32BV */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,w25q32";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/marvell/dove-d2plug.dts
index 273f12ca2512..79ee2b32409d 100644
--- a/arch/arm/boot/dts/dove-d2plug.dts
+++ b/arch/arm/boot/dts/marvell/dove-d2plug.dts
@@ -21,17 +21,17 @@
 		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
 		pinctrl-names = "default";
 
-		wlan-ap {
+		led-wlan-ap {
 			label = "wlan-ap";
 			gpios = <&gpio0 0 1>;
 		};
 
-		wlan-act {
+		led-wlan-act {
 			label = "wlan-act";
 			gpios = <&gpio0 1 1>;
 		};
 
-		bluetooth-act {
+		led-bluetooth-act {
 			label = "bt-act";
 			gpios = <&gpio0 2 1>;
 		};
@@ -62,7 +62,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Macronix MX25L3205D */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25l3205d";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-d3plug.dts b/arch/arm/boot/dts/marvell/dove-d3plug.dts
index 826026c28f90..a451fd576990 100644
--- a/arch/arm/boot/dts/dove-d3plug.dts
+++ b/arch/arm/boot/dts/marvell/dove-d3plug.dts
@@ -21,40 +21,33 @@
 		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
 		pinctrl-names = "default";
 
-		wlan-act {
+		led-wlan-act {
 			label = "wlan-act";
 			gpios = <&gpio0 0 1>;
 		};
 
-		wlan-ap {
+		led-wlan-ap {
 			label = "wlan-ap";
 			gpios = <&gpio0 1 1>;
 		};
 
-		status {
+		led-status {
 			label = "status";
 			gpios = <&gpio0 2 1>;
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 8 0>;
-			pinctrl-0 = <&pmx_gpio_8>;
-			pinctrl-names = "default";
-		};
+	usb_power: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio0 8 0>;
+		pinctrl-0 = <&pmx_gpio_8>;
+		pinctrl-names = "default";
 	};
 };
 
@@ -79,7 +72,7 @@
 	status = "okay";
 
 	/* spi0.0: 2M Flash Macronix MX25L1605D */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25l1605d";
 		spi-max-frequency = <86000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-dove-db.dts b/arch/arm/boot/dts/marvell/dove-dove-db.dts
index 1754a62e014e..c1912dc6bfc3 100644
--- a/arch/arm/boot/dts/dove-dove-db.dts
+++ b/arch/arm/boot/dts/marvell/dove-dove-db.dts
@@ -27,7 +27,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash ST-M25P32-VMF6P */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25p32";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-sbc-a510.dts b/arch/arm/boot/dts/marvell/dove-sbc-a510.dts
index 2bb85a9b7614..8585ee5533bf 100644
--- a/arch/arm/boot/dts/dove-sbc-a510.dts
+++ b/arch/arm/boot/dts/marvell/dove-sbc-a510.dts
@@ -76,22 +76,20 @@
 		stdout-path = &uart0;
 	};
 
-	regulators {
-		usb0_power: regulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
-		};
-
-		mmc_power: regulator@3 {
-			compatible = "regulator-fixed";
-			regulator-name = "MMC Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio_ext 13 GPIO_ACTIVE_HIGH>;
-		};
+	usb0_power: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	mmc_power: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MMC Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio_ext 13 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -143,6 +141,7 @@
 	gpio_ext: gpio@20 {
 		compatible = "nxp,pca9555";
 		reg = <0x20>;
+		gpio-controller;
 		#gpio-cells = <2>;
 	};
 };
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/marvell/dove.dtsi
index 3081b04e8c08..062c86361640 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/marvell/dove.dtsi
@@ -122,14 +122,24 @@
 				bus-range = <0x00 0xff>;
 
 				#interrupt-cells = <1>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 16>;
+				interrupt-names = "intx", "error";
+				interrupts = <16>, <15>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2 {
 				device_type = "pci";
 				status = "disabled";
-				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x80000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				clocks = <&gate_clk 5>;
 				marvell,pcie-port = <1>;
@@ -141,8 +151,18 @@
 				bus-range = <0x00 0xff>;
 
 				#interrupt-cells = <1>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 18>;
+				interrupt-names = "intx", "error";
+				interrupts = <18>, <17>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
@@ -175,7 +195,6 @@
 				#size-cells = <0>;
 				interrupts = <11>;
 				clock-frequency = <400000>;
-				timeout-ms = <1000>;
 				clocks = <&core_clk 0>;
 				status = "okay";
 			};
@@ -248,7 +267,7 @@
 				marvell,#interrupts = <5>;
 			};
 
-			intc: main-interrupt-ctrl@20200 {
+			intc: interrupt-controller@20200 {
 				compatible = "marvell,orion-intc";
 				interrupt-controller;
 				#interrupt-cells = <1>;
@@ -363,7 +382,6 @@
 					interrupts = <29>;
 					/* overwrite MAC address in bootloader */
 					local-mac-address = [00 00 00 00 00 00];
-					phy-handle = <&ethphy>;
 				};
 			};
 
@@ -375,10 +393,6 @@
 				interrupts = <30>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
-
-				ethphy: ethernet-phy {
-					/* set phy address in board file */
-				};
 			};
 
 			sdio0: sdio-host@92000 {
@@ -408,7 +422,7 @@
 				clocks = <&gate_clk 3>;
 				clock-names = "sata";
 				#phy-cells = <0>;
-				status = "ok";
+				status = "okay";
 			};
 
 			audio0: audio-controller@b0000 {
diff --git a/arch/arm/boot/dts/marvell/kirkwood-4i-edge-200.dts b/arch/arm/boot/dts/marvell/kirkwood-4i-edge-200.dts
new file mode 100644
index 000000000000..b1749d3f60b7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-4i-edge-200.dts
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Endian 4i Edge 200 Board Description
+ * Note: Endian UTM Mini is hardware clone of Endian Edge 200
+ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Endian 4i Edge 200";
+	compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led>;
+		pinctrl-names = "default";
+
+		led-1 {
+			function = LED_FUNCTION_SD;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth0port {
+	speed = <1000>;
+	duplex = <1>;
+};
+
+&eth1 {
+	status = "okay";
+};
+
+&eth1port {
+	phy-handle = <&ethphyb>;
+};
+
+&mdio {
+	status = "okay";
+
+	ethphyb: ethernet-phy@b {
+		reg = <0x0b>;
+
+		marvell,reg-init =
+			/* link-activity, bi-color mode 4 */
+			<3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */
+	};
+
+	switch0: switch@11 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x11>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "port1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "port2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "port3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "port4";
+			};
+
+			port@5 {
+				reg = <5>;
+				phy-mode = "rgmii-id";
+				ethernet = <&eth0port>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x00000000 0x000a0000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "u-boot-env";
+		reg = <0x000a0000 0x00060000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "kernel";
+		reg = <0x00100000 0x00400000>;
+	};
+
+	partition@500000 {
+		label = "ubi";
+		reg = <0x00500000 0x1fb00000>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_sysrst>;
+	pinctrl-names = "default";
+
+	pmx_sysrst: pmx-sysrst {
+		marvell,pins = "mpp6";
+		marvell,function = "sysrst";
+	};
+
+	pmx_sdio_cd: pmx-sdio-cd {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	pmx_led: pmx-led {
+		marvell,pins = "mpp34", "mpp35", "mpp49";
+		marvell,function = "gpio";
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata_phy0 {
+	status = "disabled";
+};
+
+&sata_phy1 {
+	status = "disabled";
+};
+
+&sdio {
+	pinctrl-0 = <&pmx_sdio_cd>;
+	pinctrl-names = "default";
+	status = "okay";
+	cd-gpios = <&gpio0 28 9>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/kirkwood-6192.dtsi b/arch/arm/boot/dts/marvell/kirkwood-6192.dtsi
index 396bcba08adb..705c0d7effed 100644
--- a/arch/arm/boot/dts/kirkwood-6192.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-6192.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-6281.dtsi b/arch/arm/boot/dts/marvell/kirkwood-6281.dtsi
index faa05849a40d..8e311165fd13 100644
--- a/arch/arm/boot/dts/kirkwood-6281.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-6281.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-6282.dtsi b/arch/arm/boot/dts/marvell/kirkwood-6282.dtsi
index e84c54b77dea..e33723160ce7 100644
--- a/arch/arm/boot/dts/kirkwood-6282.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-6282.dtsi
@@ -30,12 +30,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2,0 {
@@ -48,12 +58,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 10>;
+				interrupt-names = "intx", "error";
+				interrupts = <10>, <45>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 18>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-98dx4122.dtsi b/arch/arm/boot/dts/marvell/kirkwood-98dx4122.dtsi
index 299c147298c3..c3469a2fc58a 100644
--- a/arch/arm/boot/dts/kirkwood-98dx4122.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-98dx4122.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-b3.dts b/arch/arm/boot/dts/marvell/kirkwood-b3.dts
index 17f48f88a983..681343c1357a 100644
--- a/arch/arm/boot/dts/kirkwood-b3.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-b3.dts
@@ -9,7 +9,7 @@
  * L2 cache. If your B3 silently fails to boot, u-boot is probably too
  * old. Either upgrade, or consider the following email:
  *
- * http://lists.debian.org/debian-arm/2012/08/msg00128.html
+ * https://lists.debian.org/debian-arm/2012/08/msg00128.html
  */
 
 /dts-v1/;
@@ -187,7 +187,7 @@
 
 /* Wifi model has Atheros chipset on pcie port */
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts b/arch/arm/boot/dts/marvell/kirkwood-blackarmor-nas220.dts
index 07fbfca444d5..07fbfca444d5 100644
--- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-blackarmor-nas220.dts
diff --git a/arch/arm/boot/dts/marvell/kirkwood-c200-v1.dts b/arch/arm/boot/dts/marvell/kirkwood-c200-v1.dts
new file mode 100644
index 000000000000..f59ff7578dfc
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-c200-v1.dts
@@ -0,0 +1,310 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Ctera C200 V1 Board Description
+ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Ctera C200 V1";
+	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+
+		power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+
+		usb1 {
+			label = "USB1 Button";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+
+		usb2 {
+			label = "USB2 Button";
+			linux,code = <BTN_1>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_poweroff>;
+		pinctrl-names = "default";
+		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds>;
+		pinctrl-names = "default";
+
+		led-0 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-8 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-9 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-10 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port2>;
+		};
+
+		led-11 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-12 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port1>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth0port {
+	phy-handle = <&ethphy9>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	rtc@30 {
+		compatible = "s35390a";
+		reg = <0x30>;
+	};
+
+	lm63@4c {
+		compatible = "national,lm63";
+		reg = <0x4c>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy9: ethernet-phy@9 {
+		reg = <9>;
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <40>;
+
+	partition@0 {
+		label = "uboot";
+		reg = <0x0000000 0x200000>;
+	};
+
+	partition@200000 {
+		label = "certificate";
+		reg = <0x0200000 0x100000>;
+	};
+
+	partition@300000 {
+		label = "preset_cfg";
+		reg = <0x0300000 0x100000>;
+	};
+
+	partition@400000 {
+		label = "dev_params";
+		reg = <0x0400000 0x100000>;
+	};
+
+	partition@500000 {
+		label = "active_bank";
+		reg = <0x0500000 0x0100000>;
+	};
+
+	partition@600000 {
+		label = "magic";
+		reg = <0x0600000 0x0100000>;
+	};
+
+	partition@700000 {
+		label = "bank1";
+		reg = <0x0700000 0x2800000>;
+	};
+
+	partition@2f00000 {
+		label = "bank2";
+		reg = <0x2f00000 0x2800000>;
+	};
+
+	/* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+	partition@5a00000 {
+		label = "reserved";
+		reg = <0x5a00000 0x2000000>;
+	};
+
+	partition@7a00000 {
+		label = "rootfs";
+		reg = <0x7a00000 0x8600000>;
+	};
+};
+
+&pinctrl {
+	/* Buzzer gpios are connected to two pins of buzzer.
+	 * This buzzer require a modulated signal from gpio.
+	 * Leave it as is due lack of proper driver.
+	 */
+	pmx_buzzer: pmx-buzzer {
+		marvell,pins = "mpp12", "mpp13";
+		marvell,function = "gpio";
+	};
+
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
+			       "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
+			       "mpp45", "mpp46", "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
+		marvell,function = "gpio";
+	};
+
+	pmx_poweroff: pmx-poweroff {
+		marvell,pins = "mpp34";
+		marvell,function = "gpio";
+	};
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	port@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		#trigger-source-cells = <0>;
+
+		hub_port1: port@1 {
+			reg = <1>;
+			#trigger-source-cells = <0>;
+		};
+
+		hub_port2: port@2 {
+			reg = <2>;
+			#trigger-source-cells = <0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-cloudbox.dts b/arch/arm/boot/dts/marvell/kirkwood-cloudbox.dts
index 448b0cd23b5f..448b0cd23b5f 100644
--- a/arch/arm/boot/dts/kirkwood-cloudbox.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-cloudbox.dts
diff --git a/arch/arm/boot/dts/kirkwood-d2net.dts b/arch/arm/boot/dts/marvell/kirkwood-d2net.dts
index bd3b266dd766..bd3b266dd766 100644
--- a/arch/arm/boot/dts/kirkwood-d2net.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-d2net.dts
diff --git a/arch/arm/boot/dts/kirkwood-db-88f6281.dts b/arch/arm/boot/dts/marvell/kirkwood-db-88f6281.dts
index 2adb17c955aa..a9a8e6b744c7 100644
--- a/arch/arm/boot/dts/kirkwood-db-88f6281.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-db-88f6281.dts
@@ -18,7 +18,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-db-88f6282.dts b/arch/arm/boot/dts/marvell/kirkwood-db-88f6282.dts
index f84a48539917..6dc6579d4524 100644
--- a/arch/arm/boot/dts/kirkwood-db-88f6282.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-db-88f6282.dts
@@ -18,7 +18,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/marvell/kirkwood-db.dtsi
index 6fe2e31534af..6fe2e31534af 100644
--- a/arch/arm/boot/dts/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-db.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-dir665.dts b/arch/arm/boot/dts/marvell/kirkwood-dir665.dts
index b3ad3f607d31..0c0851cd9bec 100644
--- a/arch/arm/boot/dts/kirkwood-dir665.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dir665.dts
@@ -78,7 +78,7 @@
 
 		spi@10600 {
 			status = "okay";
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
@@ -211,18 +211,18 @@
 			};
 
 			port@1 {
-			       reg = <1>;
-			       label = "lan3";
+				reg = <1>;
+				label = "lan3";
 			};
 
 			port@2 {
-			       reg = <2>;
-			       label = "lan2";
+				reg = <2>;
+				label = "lan2";
 			};
 
 			port@3 {
-			       reg = <3>;
-			       label = "lan1";
+				reg = <3>;
+				label = "lan1";
 			};
 
 			port@4 {
@@ -232,7 +232,7 @@
 
 			port@6 {
 				reg = <6>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -251,6 +251,7 @@
 	ethernet0-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
@@ -268,7 +269,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-dns320.dts b/arch/arm/boot/dts/marvell/kirkwood-dns320.dts
index d6b0f418fd01..d6b0f418fd01 100644
--- a/arch/arm/boot/dts/kirkwood-dns320.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dns320.dts
diff --git a/arch/arm/boot/dts/kirkwood-dns325.dts b/arch/arm/boot/dts/marvell/kirkwood-dns325.dts
index 94d9c06cbbf5..94d9c06cbbf5 100644
--- a/arch/arm/boot/dts/kirkwood-dns325.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dns325.dts
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/marvell/kirkwood-dnskw.dtsi
index eb917462b219..0738eb679fcd 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-dnskw.dtsi
@@ -38,9 +38,9 @@
 		pinctrl-names = "default";
 		gpios = <&gpio1 14 GPIO_ACTIVE_HIGH
 			 &gpio1 13 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <0    0
-				      3000 1
-				      6000 2>;
+		gpio-fan,speed-map = <0    0>,
+				     <3000 1>,
+				     <6000 2>;
 	};
 
 	gpio_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/marvell/kirkwood-dockstar.dts
index 6a3f1bf6d9f1..264938dfa4d9 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dockstar.dts
@@ -34,7 +34,7 @@
 			};
 		};
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 	};
 	gpio-leds {
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/marvell/kirkwood-dreamplug.dts
index 7f326e267494..328516351e84 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dreamplug.dts
@@ -34,7 +34,7 @@
 			};
 		};
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		spi@10600 {
diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/marvell/kirkwood-ds109.dts
index 29982e7acb7f..29982e7acb7f 100644
--- a/arch/arm/boot/dts/kirkwood-ds109.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds109.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/marvell/kirkwood-ds110jv10.dts
index d68c616e9309..d68c616e9309 100644
--- a/arch/arm/boot/dts/kirkwood-ds110jv10.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds110jv10.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/marvell/kirkwood-ds111.dts
index e1420cbcd7e4..e1420cbcd7e4 100644
--- a/arch/arm/boot/dts/kirkwood-ds111.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds111.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/marvell/kirkwood-ds112.dts
index f48609e95afe..3912f1b525b6 100644
--- a/arch/arm/boot/dts/kirkwood-ds112.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds112.dts
@@ -43,7 +43,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie1 {
diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/marvell/kirkwood-ds209.dts
index f41fe95e055f..f41fe95e055f 100644
--- a/arch/arm/boot/dts/kirkwood-ds209.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds209.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/marvell/kirkwood-ds210.dts
index 729f959a7838..729f959a7838 100644
--- a/arch/arm/boot/dts/kirkwood-ds210.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds210.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/marvell/kirkwood-ds212.dts
index 416bab50d170..416bab50d170 100644
--- a/arch/arm/boot/dts/kirkwood-ds212.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds212.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/marvell/kirkwood-ds212j.dts
index 14cf4d8afaf3..14cf4d8afaf3 100644
--- a/arch/arm/boot/dts/kirkwood-ds212j.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds212j.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/marvell/kirkwood-ds409.dts
index a8650f9e3eb7..a8650f9e3eb7 100644
--- a/arch/arm/boot/dts/kirkwood-ds409.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds409.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/marvell/kirkwood-ds409slim.dts
index 27a1d840bd15..27a1d840bd15 100644
--- a/arch/arm/boot/dts/kirkwood-ds409slim.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds409slim.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/marvell/kirkwood-ds411.dts
index 86907be70cf9..1d4256ef325d 100644
--- a/arch/arm/boot/dts/kirkwood-ds411.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds411.dts
@@ -47,7 +47,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie1 {
diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/marvell/kirkwood-ds411j.dts
index bb3200daea1e..bb3200daea1e 100644
--- a/arch/arm/boot/dts/kirkwood-ds411j.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds411j.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/marvell/kirkwood-ds411slim.dts
index 9c5364a4e0a8..9c5364a4e0a8 100644
--- a/arch/arm/boot/dts/kirkwood-ds411slim.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds411slim.dts
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/marvell/kirkwood-goflexnet.dts
index 02d87e0a1061..d4cb3cd3e2a2 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-goflexnet.dts
@@ -66,7 +66,7 @@
 			};
 		};
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		sata@80000 {
diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/marvell/kirkwood-guruplug-server-plus.dts
index ff1260ee3fe8..dfb41393941d 100644
--- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-guruplug-server-plus.dts
@@ -38,7 +38,7 @@
 			};
 		};
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		sata@80000 {
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/marvell/kirkwood-ib62x0.dts
index 962a910a6f5c..962a910a6f5c 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ib62x0.dts
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/marvell/kirkwood-iconnect.dts
index 4a512d80912c..aed20185fd7a 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-iconnect.dts
@@ -72,7 +72,7 @@
 			};
 		};
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 	};
 
@@ -187,7 +187,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/marvell/kirkwood-iomega_ix2_200.dts
index 62272d58664f..2338f495d517 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-iomega_ix2_200.dts
@@ -112,7 +112,7 @@
 		};
 
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		sata@80000 {
diff --git a/arch/arm/boot/dts/kirkwood-is2.dts b/arch/arm/boot/dts/marvell/kirkwood-is2.dts
index 1bc16a5cdbaa..1bc16a5cdbaa 100644
--- a/arch/arm/boot/dts/kirkwood-is2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-is2.dts
diff --git a/arch/arm/boot/dts/kirkwood-km_common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-km_common.dtsi
index 75dc83914f56..52baffe45f12 100644
--- a/arch/arm/boot/dts/kirkwood-km_common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-km_common.dtsi
@@ -39,7 +39,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-km_fixedeth.dts b/arch/arm/boot/dts/marvell/kirkwood-km_fixedeth.dts
index 515be7bccc0a..515be7bccc0a 100644
--- a/arch/arm/boot/dts/kirkwood-km_fixedeth.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-km_fixedeth.dts
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/marvell/kirkwood-km_kirkwood.dts
index f035eff1c111..f035eff1c111 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-km_kirkwood.dts
diff --git a/arch/arm/boot/dts/marvell/kirkwood-l-50.dts b/arch/arm/boot/dts/marvell/kirkwood-l-50.dts
new file mode 100644
index 000000000000..dffb9f84e67c
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-l-50.dts
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Check Point L-50 Board Description
+ * Copyright 2020 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Check Point L-50";
+	compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
+			pinctrl-names = "default";
+
+			pmx_sysrst: pmx-sysrst {
+				marvell,pins = "mpp6";
+				marvell,function = "sysrst";
+			};
+
+			pmx_button29: pmx_button29 {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led38: pmx_led38 {
+				marvell,pins = "mpp38";
+				marvell,function = "gpio";
+			};
+
+			pmx_sdio_cd: pmx-sdio-cd {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+
+		mvsdio@90000 {
+			status = "okay";
+			cd-gpios = <&gpio1 14 9>;
+		};
+
+		i2c@11000 {
+			status = "okay";
+			clock-frequency = <400000>;
+
+			gpio2: gpio-expander@20 {
+				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
+				compatible = "semtech,sx1505q";
+				reg = <0x20>;
+
+				gpio-controller;
+			};
+
+			/* Three GPIOs from 0x21 exp. are undescribed in dts:
+			 * 1: DSL module reset (active low)
+			 * 5: mPCIE reset (active low)
+			 * 6: Express card reset (active low)
+			 */
+			gpio3: gpio-expander@21 {
+				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
+				compatible = "semtech,sx1505q";
+				reg = <0x21>;
+
+				gpio-controller;
+			};
+
+			rtc@30 {
+				compatible = "s35390a";
+				reg = <0x30>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status_green {
+			label = "l-50:green:status";
+			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		};
+
+		status_red {
+			label = "l-50:red:status";
+			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi {
+			label = "l-50:green:wifi";
+			gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		internet_green {
+			label = "l-50:green:internet";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+
+		internet_red {
+			label = "l-50:red:internet";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+		};
+
+		usb1_green {
+			label = "l-50:green:usb1";
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port3>;
+		};
+
+		usb1_red {
+			label = "l-50:red:usb1";
+			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		};
+
+		usb2_green {
+			label = "l-50:green:usb2";
+			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port1>;
+		};
+
+		usb2_red {
+			label = "l-50:red:usb2";
+			gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	usb2_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_pwr";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	usb1_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_pwr";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	mpcie_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "mpcie_pwr";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	express_card_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "express_card_pwr";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		factory_defaults {
+			label = "factory_defaults";
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy8: ethernet-phy@8 {
+		reg = <0x08>;
+	};
+
+	switch0: switch@10 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10>;
+		dsa,member = <0 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan5";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan1";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan6";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan2";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan7";
+			};
+
+			switch0port5: port@5 {
+				reg = <5>;
+				phy-mode = "rgmii-txid";
+				link = <&switch1port5>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@6 {
+				reg = <6>;
+				phy-mode = "rgmii-id";
+				ethernet = <&eth1port>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+
+	switch@11 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11>;
+		dsa,member = <0 1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan3";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan8";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan4";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "dmz";
+			};
+
+			switch1port5: port@5 {
+				reg = <5>;
+				phy-mode = "rgmii-txid";
+				link = <&switch0port5>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "dsl";
+				fixed-link {
+					speed = <100>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy8>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+		phy-mode = "rgmii";
+	};
+};
+
+&nand {
+	status = "okay";
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x00000000 0x000c0000>;
+	};
+
+	partition@a0000 {
+		label = "bootldr-env";
+		reg = <0x000c0000 0x00040000>;
+	};
+
+	partition@100000 {
+		label = "kernel-1";
+		reg = <0x00100000 0x00800000>;
+	};
+
+	partition@900000 {
+		label = "rootfs-1";
+		reg = <0x00900000 0x07100000>;
+	};
+
+	partition@7a00000 {
+		label = "kernel-2";
+		reg = <0x07a00000 0x00800000>;
+	};
+
+	partition@8200000 {
+		label = "rootfs-2";
+		reg = <0x08200000 0x07100000>;
+	};
+
+	partition@f300000 {
+		label = "default_sw";
+		reg = <0x0f300000 0x07900000>;
+	};
+
+	partition@16c00000 {
+		label = "logs";
+		reg = <0x16c00000 0x01800000>;
+	};
+
+	partition@18400000 {
+		label = "preset_cfg";
+		reg = <0x18400000 0x00100000>;
+	};
+
+	partition@18500000 {
+		label = "adsl";
+		reg = <0x18500000 0x00100000>;
+	};
+
+	partition@18600000 {
+		label = "storage";
+		reg = <0x18600000 0x07a00000>;
+	};
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&sata_phy0 {
+	status = "disabled";
+};
+
+&sata_phy1 {
+	status = "disabled";
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	port@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		#trigger-source-cells = <0>;
+
+		hub_port1: port@1 {
+			reg = <1>;
+			#trigger-source-cells = <0>;
+		};
+
+		hub_port3: port@3 {
+			reg = <3>;
+			#trigger-source-cells = <0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-laplug.dts b/arch/arm/boot/dts/marvell/kirkwood-laplug.dts
index 6158214a939a..8c2b540eaf4f 100644
--- a/arch/arm/boot/dts/kirkwood-laplug.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-laplug.dts
@@ -160,7 +160,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-6282.dtsi b/arch/arm/boot/dts/marvell/kirkwood-linkstation-6282.dtsi
index 377b6e970259..dfac2045a1eb 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-6282.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-6282.dtsi
@@ -118,10 +118,11 @@
 		gpios = <&gpio0 17 GPIO_ACTIVE_LOW
 			 &gpio0 16 GPIO_ACTIVE_LOW>;
 
-		gpio-fan,speed-map = <0 3
-				1500 2
-				3250 1
-				5000 0>;
+		gpio-fan,speed-map =
+				<   0 3>,
+				<1500 2>,
+				<3250 1>,
+				<5000 0>;
 
 		alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi b/arch/arm/boot/dts/marvell/kirkwood-linkstation-duo-6281.dtsi
index ba629e02ba31..ba629e02ba31 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-duo-6281.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lsqvl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsqvl.dts
index 8bb381088910..8bb381088910 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lsqvl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsqvl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lsvl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsvl.dts
index 3f2a0bfe03ed..3f2a0bfe03ed 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lsvl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsvl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswsxl.dts
index c42d0da38fe7..c42d0da38fe7 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswsxl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswvl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswvl.dts
index e0f62adc0d5d..e0f62adc0d5d 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lswvl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswvl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswxl.dts
index c6024b569423..0425df8cb91c 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswxl.dts
@@ -69,10 +69,11 @@
 		gpios = <&gpio1 16 GPIO_ACTIVE_LOW
 			 &gpio1 15 GPIO_ACTIVE_LOW>;
 
-		gpio-fan,speed-map = <0 3
-				1500 2
-				3250 1
-				5000 0>;
+		gpio-fan,speed-map =
+				<   0 3>,
+				<1500 2>,
+				<3250 1>,
+				<5000 0>;
 
 		alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation.dtsi b/arch/arm/boot/dts/marvell/kirkwood-linkstation.dtsi
index 407d6d8b3a7f..b54c9980f636 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation.dtsi
@@ -156,7 +156,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-linksys-viper.dts b/arch/arm/boot/dts/marvell/kirkwood-linksys-viper.dts
index 2f9660f3b457..27fd6e2337d5 100644
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linksys-viper.dts
@@ -198,7 +198,7 @@
 
 			port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -221,6 +221,7 @@
 	ethernet0-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
diff --git a/arch/arm/boot/dts/kirkwood-lschlv2.dts b/arch/arm/boot/dts/marvell/kirkwood-lschlv2.dts
index 1d737d903f5f..1d737d903f5f 100644
--- a/arch/arm/boot/dts/kirkwood-lschlv2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-lschlv2.dts
diff --git a/arch/arm/boot/dts/kirkwood-lsxhl.dts b/arch/arm/boot/dts/marvell/kirkwood-lsxhl.dts
index a56e0d797778..a56e0d797778 100644
--- a/arch/arm/boot/dts/kirkwood-lsxhl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-lsxhl.dts
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/marvell/kirkwood-lsxl.dtsi
index 7b151acb9984..f80af24b9e90 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-lsxl.dtsi
@@ -10,6 +10,11 @@
 
 	ocp@f1000000 {
 		pinctrl: pin-controller@10000 {
+			/* Non-default UART pins */
+			pmx_uart0: pmx-uart0 {
+				marvell,pins = "mpp4", "mpp5";
+			};
+
 			pmx_power_hdd: pmx-power-hdd {
 				marvell,pins = "mpp10";
 				marvell,function = "gpo";
@@ -167,10 +172,11 @@
 		pinctrl-names = "default";
 		gpios = <&gpio0 19 GPIO_ACTIVE_LOW
 		         &gpio0 18 GPIO_ACTIVE_LOW>;
-		gpio-fan,speed-map = <0    3
-		                      1500 2
-		                      3250 1
-		                      5000 0>;
+		gpio-fan,speed-map =
+				<0    3>,
+				<1500 2>,
+				<3250 1>,
+				<5000 0>;
 		alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
 
@@ -213,22 +219,11 @@
 &mdio {
 	status = "okay";
 
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-
 	ethphy1: ethernet-phy@8 {
 		reg = <8>;
 	};
 };
 
-&eth0 {
-	status = "okay";
-	ethernet0-port@0 {
-		phy-handle = <&ethphy0>;
-	};
-};
-
 &eth1 {
 	status = "okay";
 	ethernet1-port@0 {
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/marvell/kirkwood-mplcec4.dts
index b80d12f6aa49..e87ea7146546 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-mplcec4.dts
@@ -8,10 +8,10 @@
 	model = "MPL CEC4";
 	compatible = "mpl,cec4-10", "mpl,cec4", "marvell,kirkwood-88f6281", "marvell,kirkwood";
 
-        memory {
-                device_type = "memory";
-                reg = <0x00000000 0x20000000>;
-        };
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
 
 	chosen {
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
@@ -66,8 +66,8 @@
 			};
 		};
 
-                i2c@11000 {
-                        status = "okay";
+		i2c@11000 {
+			status = "okay";
 
 			rtc@51 {
 				compatible = "nxp,pcf8563";
@@ -79,7 +79,7 @@
 				reg = <0x57>;
 			};
 
-                };
+		};
 
 		serial@12000 {
 			status = "okay";
@@ -208,7 +208,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/marvell/kirkwood-mv88f6281gtw-ge.dts
index 2e1a75348908..5a77286136c7 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-mv88f6281gtw-ge.dts
@@ -149,7 +149,7 @@
 
 			port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -166,11 +166,12 @@
 	ethernet0-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nas2big.dts b/arch/arm/boot/dts/marvell/kirkwood-nas2big.dts
index 6a2934b7d0ce..0b0a15093146 100644
--- a/arch/arm/boot/dts/kirkwood-nas2big.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nas2big.dts
@@ -131,7 +131,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-net2big.dts b/arch/arm/boot/dts/marvell/kirkwood-net2big.dts
index 3e3ac289e5b0..d5f6bb50ba11 100644
--- a/arch/arm/boot/dts/kirkwood-net2big.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-net2big.dts
@@ -46,11 +46,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <32768>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/kirkwood-net5big.dts b/arch/arm/boot/dts/marvell/kirkwood-net5big.dts
index cba8a2b6f6d9..2497ad26b5b6 100644
--- a/arch/arm/boot/dts/kirkwood-net5big.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-net5big.dts
@@ -78,11 +78,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <32768>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 
 	netxbig-leds {
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_duo_v2.dts
index cb564c3bcdc4..cb564c3bcdc4 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_duo_v2.dts
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_nv+_v2.dts
index 8cc8550242ef..6cf76430cfab 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_nv+_v2.dts
@@ -78,11 +78,11 @@
 		};
 
 		clocks {
-		       g762_clk: g762-oscillator {
-				 compatible = "fixed-clock";
-				 #clock-cells = <0>;
-				 clock-frequency = <8192>;
-		       };
+			g762_clk: g762-oscillator {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <8192>;
+			};
 		};
 
 		i2c@11000 {
@@ -113,6 +113,20 @@
 		};
 	};
 
+	auxdisplay {
+		compatible = "hit,hd44780";
+		data-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>,
+				<&gpio1 1 GPIO_ACTIVE_HIGH>,
+				<&gpio1 3 GPIO_ACTIVE_HIGH>,
+				<&gpio1 17 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		rs-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		rw-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		backlight-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		display-height-chars = <2>;
+		display-width-chars = <16>;
+	};
+
 	gpio-leds {
 		compatible = "gpio-leds";
 		pinctrl-0 = < &pmx_led_blue_power &pmx_led_blue_backup
@@ -252,7 +266,7 @@
 
 /* Connected to NEC uPD720200 USB 3.0 controller */
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-netxbig.dtsi b/arch/arm/boot/dts/marvell/kirkwood-netxbig.dtsi
index b5737026e244..b5737026e244 100644
--- a/arch/arm/boot/dts/kirkwood-netxbig.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-netxbig.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-ns2-common.dtsi
index 51530ea86622..51530ea86622 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2-common.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-ns2.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2.dts
index 7b67083e1ec0..7b67083e1ec0 100644
--- a/arch/arm/boot/dts/kirkwood-ns2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2.dts
diff --git a/arch/arm/boot/dts/kirkwood-ns2lite.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2lite.dts
index b0cb5907ed63..b0cb5907ed63 100644
--- a/arch/arm/boot/dts/kirkwood-ns2lite.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2lite.dts
diff --git a/arch/arm/boot/dts/kirkwood-ns2max.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2max.dts
index c0a087e77408..044958bc55da 100644
--- a/arch/arm/boot/dts/kirkwood-ns2max.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2max.dts
@@ -29,15 +29,15 @@
 			 &gpio1  1 GPIO_ACTIVE_LOW
 			 &gpio0 23 GPIO_ACTIVE_LOW>;
 		gpio-fan,speed-map =
-			<   0  0
-			 1500 15
-			 1700 14
-			 1800 13
-			 2100 12
-			 3100 11
-			 3300 10
-			 4300  9
-			 5500  8>;
+			<   0  0>,
+			<1500 15>,
+			<1700 14>,
+			<1800 13>,
+			<2100 12>,
+			<3100 11>,
+			<3300 10>,
+			<4300  9>,
+			<5500  8>;
 		alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
 	};
 
diff --git a/arch/arm/boot/dts/kirkwood-ns2mini.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2mini.dts
index 5b9fa14b6428..3fbe008f9141 100644
--- a/arch/arm/boot/dts/kirkwood-ns2mini.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2mini.dts
@@ -30,15 +30,15 @@
 			 &gpio1  1 GPIO_ACTIVE_LOW
 			 &gpio0 23 GPIO_ACTIVE_LOW>;
 		gpio-fan,speed-map =
-			<   0  0
-			 3000 15
-			 3180 14
-			 4140 13
-			 4570 12
-			 6760 11
-			 7140 10
-			 7980  9
-			 9200  8>;
+			<   0  0>,
+			<3000 15>,
+			<3180 14>,
+			<4140 13>,
+			<4570 12>,
+			<6760 11>,
+			<7140 10>,
+			<7980  9>,
+			<9200  8>;
 		alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
 	};
 
diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa310.dts
index 9b861c2e76c5..c1799a07816e 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa310.dts
@@ -131,7 +131,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nsa310a.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa310a.dts
index b85e314f045a..b85e314f045a 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310a.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa310a.dts
diff --git a/arch/arm/boot/dts/marvell/kirkwood-nsa310s.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa310s.dts
new file mode 100644
index 000000000000..49da633a1bc0
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa310s.dts
@@ -0,0 +1,259 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * ZyXEL NSA310S Board Description
+ * Copyright 2020-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ * Copyright (c) 2015-2021, Tony Dinh <mibodhi@gmail.com>
+ * Copyright (c) 2014, Adam Baker <linux@baker-net.org.uk>
+ * Based upon the board setup file created by Peter Schildmann
+ */
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "ZyXEL NSA310S";
+	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_pwr_off>;
+		pinctrl-names = "default";
+		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+
+		power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		copy {
+			label = "Copy Button";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds>;
+		pinctrl-names = "default";
+
+		led-1 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_USB;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-host";
+		};
+
+		led-3 {
+			function = LED_FUNCTION_DISK;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata1";
+		};
+
+		led-4 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-6 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-7 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	usb0_power: regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+	};
+
+	sata1_power: regulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 Power";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	thermal-zones {
+		disk-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&hdd_temp>;
+
+			trips {
+				disk_alert: disk-alert {
+					temperature = <40000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				disk_crit: disk-crit {
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	rtc@68 {
+		compatible = "htk,ht1382";
+		reg = <0x68>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		reg = <1>;
+		phy-mode = "rgmii-id";
+		marvell,reg-init = <0x1 0x16 0x0 0x3>,
+				   <0x1 0x10 0x0 0x1017>,
+				   <0x1 0x11 0x0 0x4408>,
+				   <0x1 0x16 0x0 0x0>;
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <35>;
+
+	partition@0 {
+		label = "uboot";
+		reg = <0x0000000 0x00c0000>;
+		read-only;
+	};
+	partition@c0000 {
+		label = "uboot_env";
+		reg = <0x00c0000 0x0080000>;
+	};
+	partition@140000 {
+		label = "ubi";
+		reg = <0x0140000 0x7ec0000>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp24", "mpp25", "mpp26";
+		marvell,function = "gpio";
+	};
+
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23",
+						"mpp28", "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_power: pmx-power {
+		marvell,pins = "mpp21", "mpp33";
+		marvell,function = "gpio";
+	};
+
+	pmx_pwr_off: pmx-pwr-off {
+		marvell,pins = "mpp27";
+		marvell,function = "gpio";
+	};
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+	nr-ports = <1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hdd_temp: sata-port@0 {
+		reg = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/kirkwood-nsa320.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
index b69b096f267b..652405e65006 100644
--- a/arch/arm/boot/dts/kirkwood-nsa320.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
@@ -211,7 +211,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa325.dts
index 6f8085dbb1f4..371456de34b2 100644
--- a/arch/arm/boot/dts/kirkwood-nsa325.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa325.dts
@@ -224,7 +224,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-nsa3x0-common.dtsi
index 2c4037b07282..ea3d36512e9f 100644
--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa3x0-common.dtsi
@@ -45,7 +45,7 @@
 		};
 
 		serial@12000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		sata@80000 {
@@ -150,7 +150,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a6.dts
index 8ea430168ea5..8ea430168ea5 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a6.dts
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a7.dts b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a7.dts
index 946f0f453dd1..946f0f453dd1 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a7.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a7.dts
diff --git a/arch/arm/boot/dts/kirkwood-openrd-base.dts b/arch/arm/boot/dts/marvell/kirkwood-openrd-base.dts
index 094191ece3d7..094191ece3d7 100644
--- a/arch/arm/boot/dts/kirkwood-openrd-base.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd-base.dts
diff --git a/arch/arm/boot/dts/kirkwood-openrd-client.dts b/arch/arm/boot/dts/marvell/kirkwood-openrd-client.dts
index d4e0b8150a84..d4e0b8150a84 100644
--- a/arch/arm/boot/dts/kirkwood-openrd-client.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd-client.dts
diff --git a/arch/arm/boot/dts/kirkwood-openrd-ultimate.dts b/arch/arm/boot/dts/marvell/kirkwood-openrd-ultimate.dts
index 888e13320c19..888e13320c19 100644
--- a/arch/arm/boot/dts/kirkwood-openrd-ultimate.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd-ultimate.dts
diff --git a/arch/arm/boot/dts/kirkwood-openrd.dtsi b/arch/arm/boot/dts/marvell/kirkwood-openrd.dtsi
index 47f03c69c55a..47f03c69c55a 100644
--- a/arch/arm/boot/dts/kirkwood-openrd.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/marvell/kirkwood-pogo_e02.dts
index f9e95e55f36d..f9e95e55f36d 100644
--- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-pogo_e02.dts
diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/marvell/kirkwood-pogoplug-series-4.dts
index 5aa4669ae254..5aa4669ae254 100644
--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-pogoplug-series-4.dts
diff --git a/arch/arm/boot/dts/marvell/kirkwood-rd88f6192.dts b/arch/arm/boot/dts/marvell/kirkwood-rd88f6192.dts
new file mode 100644
index 000000000000..f00325ffde07
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6192.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell RD88F6192 Board descrition
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are common between the three
+ * variants of the Marvell Kirkwood Development Board.
+ */
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+	model = "Marvell RD88F6192 reference design";
+	compatible = "marvell,rd88f6192", "marvell,kirkwood-88f6192", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = <&pmx_usb_power>;
+			pinctrl-names = "default";
+
+			pmx_usb_power: pmx-usb-power {
+				marvell,pins = "mpp10";
+				marvell,function = "gpo";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+
+		};
+
+		spi@10600 {
+			status = "okay";
+
+			m25p128@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "st,m25p128", "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <20000000>;
+				mode = <0>;
+			};
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "USB VBUS";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281-a.dts b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-a.dts
index 5da163591bbf..5da163591bbf 100644
--- a/arch/arm/boot/dts/kirkwood-rd88f6281-a.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-a.dts
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-z0.dts
index 9d88301daf0e..72edd47e19ff 100644
--- a/arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-z0.dts
@@ -19,7 +19,7 @@
 };
 
 &eth1 {
-      status = "disabled";
+	status = "disabled";
 };
 
 &switch {
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281.dtsi
index f1f8eee132e8..9d62f910cddf 100644
--- a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281.dtsi
@@ -48,7 +48,7 @@
 			cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
 			/* No WP GPIO */
 		};
-       };
+	};
 };
 
 &nand {
@@ -105,7 +105,7 @@
 
 			port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -126,7 +126,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/marvell/kirkwood-rs212.dts
index c51cea883215..4ad412115a24 100644
--- a/arch/arm/boot/dts/kirkwood-rs212.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rs212.dts
@@ -43,7 +43,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie1 {
diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/marvell/kirkwood-rs409.dts
index 43673b03cb35..43673b03cb35 100644
--- a/arch/arm/boot/dts/kirkwood-rs409.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rs409.dts
diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/marvell/kirkwood-rs411.dts
index 41fa63cec839..41fa63cec839 100644
--- a/arch/arm/boot/dts/kirkwood-rs411.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rs411.dts
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-common.dtsi
index 0a698d3b7393..0a698d3b7393 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-common.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-esata.dts b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-esata.dts
index ae8f493c9a0f..ae8f493c9a0f 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-esata.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-esata.dts
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug.dts b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug.dts
index c73cc904e5c4..c73cc904e5c4 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug.dts
diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/marvell/kirkwood-synology.dtsi
index 217bd374e52b..20964eb48fd7 100644
--- a/arch/arm/boot/dts/kirkwood-synology.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-synology.dtsi
@@ -198,7 +198,7 @@
 		spi@10600 {
 			status = "okay";
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "st,m25p80", "jedec,spi-nor";
@@ -286,14 +286,15 @@
 		gpios = <&gpio1 0 GPIO_ACTIVE_HIGH
 			 &gpio1 1 GPIO_ACTIVE_HIGH
 			 &gpio1 2 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2200 1
-				       2500 2
-				       3000 4
-				       3300 3
-				       3700 5
-				       3800 6
-				       4200 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2200 1>,
+				<2500 2>,
+				<3000 4>,
+				<3300 3>,
+				<3700 5>,
+				<3800 6>,
+				<4200 7>;
 	};
 
 	gpio-fan-150-15-18 {
@@ -306,14 +307,15 @@
 			 &gpio0 16 GPIO_ACTIVE_HIGH
 			 &gpio0 17 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2200 1
-				       2500 2
-				       3000 4
-				       3300 3
-				       3700 5
-				       3800 6
-				       4200 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2200 1>,
+				<2500 2>,
+				<3000 4>,
+				<3300 3>,
+				<3700 5>,
+				<3800 6>,
+				<4200 7>;
 	};
 
 	gpio-fan-100-32-35 {
@@ -326,14 +328,15 @@
 			 &gpio1 1 GPIO_ACTIVE_HIGH
 			 &gpio1 2 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-fan-100-15-18 {
@@ -346,14 +349,15 @@
 			 &gpio0 16 GPIO_ACTIVE_HIGH
 			 &gpio0 17 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-fan-100-15-35-1 {
@@ -366,14 +370,15 @@
 			 &gpio0 16 GPIO_ACTIVE_HIGH
 			 &gpio0 17 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-fan-100-15-35-3 {
@@ -388,14 +393,15 @@
 		alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH
 			       &gpio1 12 GPIO_ACTIVE_HIGH
 			       &gpio1 13 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-leds-alarm-12 {
@@ -847,7 +853,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/marvell/kirkwood-t5325.dts
index fe63b3a03a72..ad093324e075 100644
--- a/arch/arm/boot/dts/kirkwood-t5325.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-t5325.dts
@@ -219,7 +219,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/marvell/kirkwood-topkick.dts
index a5b51e29f63e..a5b51e29f63e 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-topkick.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/marvell/kirkwood-ts219-6281.dts
index 30892c19aceb..30892c19aceb 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6281.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts219-6281.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/marvell/kirkwood-ts219-6282.dts
index aba1205981f1..aba1205981f1 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts219-6282.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/marvell/kirkwood-ts219.dtsi
index 994cabcf4b51..1939462a5f48 100644
--- a/arch/arm/boot/dts/kirkwood-ts219.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts219.dtsi
@@ -86,7 +86,7 @@
 	status = "okay";
 
 	ethphy0: ethernet-phy@X {
-                /* overwrite reg property in board file */
+		/* overwrite reg property in board file */
 	};
 };
 
@@ -98,7 +98,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-ts419-6281.dts b/arch/arm/boot/dts/marvell/kirkwood-ts419-6281.dts
index 4a42ebcca4f0..4a42ebcca4f0 100644
--- a/arch/arm/boot/dts/kirkwood-ts419-6281.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts419-6281.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts419-6282.dts b/arch/arm/boot/dts/marvell/kirkwood-ts419-6282.dts
index be772e194c2b..be772e194c2b 100644
--- a/arch/arm/boot/dts/kirkwood-ts419-6282.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts419-6282.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts419.dtsi b/arch/arm/boot/dts/marvell/kirkwood-ts419.dtsi
index 717236853e45..717236853e45 100644
--- a/arch/arm/boot/dts/kirkwood-ts419.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts419.dtsi
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/marvell/kirkwood.dtsi
index 2161e23bd98e..815ef7719d13 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood.dtsi
@@ -24,9 +24,9 @@
 	};
 
 	aliases {
-	       gpio0 = &gpio0;
-	       gpio1 = &gpio1;
-	       i2c0 = &i2c0;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		i2c0 = &i2c0;
 	};
 
 	mbus@f1000000 {
@@ -228,7 +228,7 @@
 			reg = <0x20128 0x4>;
 		};
 
-		intc: main-interrupt-ctrl@20200 {
+		intc: interrupt-controller@20200 {
 			compatible = "marvell,orion-intc";
 			interrupt-controller;
 			#interrupt-cells = <1>;
@@ -279,15 +279,15 @@
 			clocks = <&gate_clk 8>;
 
 			xor00 {
-			      interrupts = <5>;
-			      dmacap,memcpy;
-			      dmacap,xor;
+				interrupts = <5>;
+				dmacap,memcpy;
+				dmacap,xor;
 			};
 			xor01 {
-			      interrupts = <6>;
-			      dmacap,memcpy;
-			      dmacap,xor;
-			      dmacap,memset;
+				interrupts = <6>;
+				dmacap,memcpy;
+				dmacap,xor;
+				dmacap,memset;
 			};
 		};
 
@@ -299,15 +299,15 @@
 			clocks = <&gate_clk 16>;
 
 			xor00 {
-			      interrupts = <7>;
-			      dmacap,memcpy;
-			      dmacap,xor;
+				interrupts = <7>;
+				dmacap,memcpy;
+				dmacap,xor;
 			};
 			xor01 {
-			      interrupts = <8>;
-			      dmacap,memcpy;
-			      dmacap,xor;
-			      dmacap,memset;
+				interrupts = <8>;
+				dmacap,memcpy;
+				dmacap,xor;
+				dmacap,memset;
 			};
 		};
 
@@ -369,7 +369,7 @@
 			clocks = <&gate_clk 14>;
 			clock-names = "sata";
 			#phy-cells = <0>;
-			status = "ok";
+			status = "okay";
 		};
 
 		sata_phy1: sata-phy@84000 {
@@ -378,7 +378,7 @@
 			clocks = <&gate_clk 15>;
 			clock-names = "sata";
 			#phy-cells = <0>;
-			status = "ok";
+			status = "okay";
 		};
 
 		audio0: audio-controller@a0000 {
diff --git a/arch/arm/boot/dts/marvell/mmp2-brownstone.dts b/arch/arm/boot/dts/marvell/mmp2-brownstone.dts
new file mode 100644
index 000000000000..04f1ae1382e7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/mmp2-brownstone.dts
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2012 Marvell Technology Group Ltd.
+ *  Author: Haojian Zhuang <haojian.zhuang@marvell.com>
+ */
+
+/dts-v1/;
+#include "mmp2.dtsi"
+
+/ {
+	model = "Marvell MMP2 Brownstone Development Board";
+	compatible = "mrvl,mmp2-brownstone", "mrvl,mmp2";
+
+	chosen {
+		bootargs = "console=ttyS2,38400 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&twsi1 {
+	status = "okay";
+	pmic: max8925@3c {
+		compatible = "maxium,max8925";
+		reg = <0x3c>;
+		interrupts = <1>;
+		interrupt-parent = <&intcmux4>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		maxim,tsc-irq = <0>;
+
+		regulators {
+			SDV1 {
+				regulator-min-microvolt = <637500>;
+				regulator-max-microvolt = <1425000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			SDV2 {
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <2225000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			SDV3 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO1 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO2 {
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <2250000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO3 {
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <2250000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO4 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO5 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO6 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO7 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO8 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO9 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO10 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+			};
+			LDO11 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO12 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO13 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO14 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO15 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO16 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO17 {
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <2250000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO18 {
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <2250000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO19 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO20 {
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+		backlight {
+			maxim,max8925-dual-string = <0>;
+		};
+		charger {
+			batt-detect = <0>;
+			topoff-threshold = <1>;
+			fast-charge = <7>;
+			no-temp-support = <0>;
+			no-insert-detect = <0>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts b/arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dts
index 6cfa0d4a1884..55ea87870af3 100644
--- a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts
+++ b/arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dts
@@ -2,7 +2,7 @@
 /*
  * OLPC XO 1.75 Laptop.
  *
- * Copyright (C) 2018,2019 Lubomir Rintel <lkundrak@v3.sk>
+ * Copyright (C) 2018,2019,2020 Lubomir Rintel <lkundrak@v3.sk>
  */
 
 /dts-v1/;
@@ -10,6 +10,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/marvell,mmp2-audio.h>
 
 / {
 	model = "OLPC XO-1.75";
@@ -32,8 +33,7 @@
 		};
 	};
 
-	memory {
-		linux,usable-memory = <0x0 0x1f800000>;
+	memory@0 {
 		available = <0xcf000 0x1ef31000 0x1000 0xbf000>;
 		reg = <0x0 0x20000000>;
 		device_type = "memory";
@@ -57,30 +57,12 @@
 			linux,code = <SW_TABLET_MODE>;
 			wakeup-source;
 		};
-
-		microphone_insert {
-			label = "Microphone Plug";
-			gpios = <&gpio 96 GPIO_ACTIVE_HIGH>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_MICROPHONE_INSERT>;
-			debounce-interval = <100>;
-			wakeup-source;
-		};
-
-		headphone_insert {
-			label = "Headphone Plug";
-			gpios = <&gpio 97 GPIO_ACTIVE_HIGH>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_HEADPHONE_INSERT>;
-			debounce-interval = <100>;
-			wakeup-source;
-		};
 	};
 
-	camera_i2c {
+	i2c {
 		compatible = "i2c-gpio";
-		gpios = <&gpio 109 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>,
-			<&gpio 108 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		sda-gpios = <&gpio 109 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio 108 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		i2c-gpio,timeout-ms = <1000>;
@@ -123,6 +105,18 @@
 		reset-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>;
 	};
 
+	sound-card {
+		compatible = "audio-graph-card";
+		label = "OLPC XO";
+		dais = <&sspa0_dai>;
+		routing = "Headphones", "HPOL",
+			  "Headphones", "HPOR",
+			  "MIC2", "Mic Jack";
+		widgets = "Headphone", "Headphones", "Microphone", "Mic Jack";
+		hp-det-gpio = <&gpio 97 GPIO_ACTIVE_HIGH>;
+		mic-det-gpio = <&gpio 96 GPIO_ACTIVE_HIGH>;
+	};
+
 	soc {
 		axi@d4200000 {
 			ap-sp@d4290000 {
@@ -197,6 +191,14 @@
 		compatible = "realtek,alc5631";
 		reg = <0x1a>;
 		status = "okay";
+
+		port {
+			rt5631_0: endpoint {
+				mclk-fs = <256>;
+				clocks = <&audio_clk MMP2_CLK_AUDIO_SYSCLK>;
+				remote-endpoint = <&sspa0_0>;
+			};
+		};
 	};
 };
 
@@ -224,12 +226,12 @@
 	#address-cells = <0>;
 	spi-slave;
 	status = "okay";
-	ready-gpio = <&gpio 125 GPIO_ACTIVE_HIGH>;
+	ready-gpios = <&gpio 125 GPIO_ACTIVE_HIGH>;
 
 	slave {
 		compatible = "olpc,xo1.75-ec";
 		spi-cpha;
-		cmd-gpio = <&gpio 155 GPIO_ACTIVE_HIGH>;
+		cmd-gpios = <&gpio 155 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -242,3 +244,34 @@
 		};
 	};
 };
+
+&asram {
+	status = "okay";
+};
+
+&adma0 {
+	status = "okay";
+};
+
+&audio_clk {
+	status = "okay";
+};
+
+&sspa0 {
+	status = "okay";
+	dmas = <&adma0 0>, <&adma0 1>;
+	dma-names = "tx", "rx";
+
+	sspa0_dai: port {
+		sspa0_0: endpoint {
+			remote-endpoint = <&rt5631_0>;
+			frame-master;
+			bitclock-master;
+			dai-format = "i2s";
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/marvell/mmp2.dtsi
index 6a2f072c1d0a..987d792f67ea 100644
--- a/arch/arm/boot/dts/mmp2.dtsi
+++ b/arch/arm/boot/dts/marvell/mmp2.dtsi
@@ -5,6 +5,8 @@
  */
 
 #include <dt-bindings/clock/marvell,mmp2.h>
+#include <dt-bindings/power/marvell,mmp2.h>
+#include <dt-bindings/clock/marvell,mmp2-audio.h>
 
 / {
 	#address-cells = <1>;
@@ -38,6 +40,17 @@
 			reg = <0xd4200000 0x00200000>;
 			ranges;
 
+			gpu: gpu@d420d000 {
+				compatible = "vivante,gc";
+				reg = <0xd420d000 0x4000>;
+				interrupts = <8>;
+				status = "disabled";
+				clocks = <&soc_clocks MMP2_CLK_GPU_3D>,
+					 <&soc_clocks MMP2_CLK_GPU_BUS>;
+				clock-names = "core", "bus";
+				power-domains = <&soc_clocks MMP2_POWER_DOMAIN_GPU>;
+			};
+
 			intc: interrupt-controller@d4282000 {
 				compatible = "mrvl,mmp2-intc";
 				interrupt-controller;
@@ -192,6 +205,63 @@
 				clock-output-names = "mclk";
 				status = "disabled";
 			};
+
+			adma0: dma-controller@d42a0800 {
+				compatible = "marvell,adma-1.0";
+				reg = <0xd42a0800 0x100>;
+				interrupts = <48>;
+				#dma-cells = <1>;
+				asram = <&asram>;
+				iram = <&asram>;
+				status = "disabled";
+			};
+
+			adma1: dma-controller@d42a0900 {
+				compatible = "marvell,adma-1.0";
+				reg = <0xd42a0900 0x100>;
+				interrupts = <48>;
+				#dma-cells = <1>;
+				status = "disabled";
+			};
+
+			audio_clk: clocks@d42a0c30 {
+				compatible = "marvell,mmp2-audio-clock";
+				reg = <0xd42a0c30 0x10>;
+				clock-names = "audio", "vctcxo", "i2s0", "i2s1";
+				clocks = <&soc_clocks MMP2_CLK_AUDIO>,
+					 <&soc_clocks MMP2_CLK_VCTCXO>,
+					 <&soc_clocks MMP2_CLK_I2S0>,
+					 <&soc_clocks MMP2_CLK_I2S1>;
+				power-domains = <&soc_clocks MMP2_POWER_DOMAIN_AUDIO>;
+				#clock-cells = <1>;
+				status = "disabled";
+			};
+
+			sspa0: audio-controller@d42a0c00 {
+				compatible = "marvell,mmp-sspa";
+				reg = <0xd42a0c00 0x30>,
+				      <0xd42a0c80 0x30>;
+				interrupts = <2>;
+				clock-names = "audio", "bitclk";
+				clocks = <&soc_clocks MMP2_CLK_AUDIO>,
+					 <&audio_clk MMP2_CLK_AUDIO_SSPA0>;
+				power-domains = <&soc_clocks MMP2_POWER_DOMAIN_AUDIO>;
+				#sound-dai-cells = <0>;
+				status = "disabled";
+			};
+
+			sspa1: audio-controller@d42a0d00 {
+				compatible = "marvell,mmp-sspa";
+				reg = <0xd42a0d00 0x30>,
+				      <0xd42a0d80 0x30>;
+				interrupts = <3>;
+				clock-names = "audio", "bitclk";
+				clocks = <&soc_clocks MMP2_CLK_AUDIO>,
+					 <&audio_clk MMP2_CLK_AUDIO_SSPA1>;
+				power-domains = <&soc_clocks MMP2_POWER_DOMAIN_AUDIO>;
+				#sound-dai-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		apb@d4000000 {	/* APB */
@@ -201,6 +271,16 @@
 			reg = <0xd4000000 0x00200000>;
 			ranges;
 
+			dma-controller@d4000000 {
+				compatible = "marvell,pdma-1.0";
+				reg = <0xd4000000 0x10000>;
+				interrupts = <48>;
+				/* For backwards compatibility: */
+				#dma-channels = <16>;
+				dma-channels = <16>;
+				status = "disabled";
+			};
+
 			timer0: timer@d4014000 {
 				compatible = "mrvl,mmp-timer";
 				reg = <0xd4014000 0x100>;
@@ -208,8 +288,8 @@
 				clocks = <&soc_clocks MMP2_CLK_TIMER>;
 			};
 
-			uart1: uart@d4030000 {
-				compatible = "mrvl,mmp-uart";
+			uart1: serial@d4030000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4030000 0x1000>;
 				interrupts = <27>;
 				clocks = <&soc_clocks MMP2_CLK_UART0>;
@@ -218,8 +298,8 @@
 				status = "disabled";
 			};
 
-			uart2: uart@d4017000 {
-				compatible = "mrvl,mmp-uart";
+			uart2: serial@d4017000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4017000 0x1000>;
 				interrupts = <28>;
 				clocks = <&soc_clocks MMP2_CLK_UART1>;
@@ -228,8 +308,8 @@
 				status = "disabled";
 			};
 
-			uart3: uart@d4018000 {
-				compatible = "mrvl,mmp-uart";
+			uart3: serial@d4018000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4018000 0x1000>;
 				interrupts = <24>;
 				clocks = <&soc_clocks MMP2_CLK_UART2>;
@@ -238,8 +318,8 @@
 				status = "disabled";
 			};
 
-			uart4: uart@d4016000 {
-				compatible = "mrvl,mmp-uart";
+			uart4: serial@d4016000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4016000 0x1000>;
 				interrupts = <46>;
 				clocks = <&soc_clocks MMP2_CLK_UART3>;
@@ -364,7 +444,7 @@
 			rtc: rtc@d4010000 {
 				compatible = "mrvl,mmp-rtc";
 				reg = <0xd4010000 0x1000>;
-				interrupts = <1 0>;
+				interrupts = <1>, <0>;
 				interrupt-names = "rtc 1Hz", "rtc alarm";
 				interrupt-parent = <&intcmux5>;
 				clocks = <&soc_clocks MMP2_CLK_RTC>;
@@ -413,14 +493,24 @@
 			};
 		};
 
+		asram: sram@e0000000 {
+			compatible = "mmio-sram";
+			reg = <0xe0000000 0x10000>;
+			ranges = <0 0xe0000000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
+
 		soc_clocks: clocks {
 			compatible = "marvell,mmp2-clock";
-			reg = <0xd4050000 0x1000>,
+			reg = <0xd4050000 0x2000>,
 			      <0xd4282800 0x400>,
 			      <0xd4015000 0x1000>;
 			reg-names = "mpmu", "apmu", "apbc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			#power-domain-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/marvell/mmp3-dell-ariel.dts b/arch/arm/boot/dts/marvell/mmp3-dell-ariel.dts
new file mode 100644
index 000000000000..fe6df364a9eb
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/mmp3-dell-ariel.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
+ *
+ * Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
+ */
+
+/dts-v1/;
+#include "mmp3.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Dell Ariel";
+	compatible = "dell,wyse-ariel", "marvell,mmp3";
+
+	aliases {
+		serial2 = &uart3;
+	};
+
+	chosen {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		ranges;
+		bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
+	};
+
+	memory@0 {
+		available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
+		reg = <0x0 0x80000000>;
+		device_type = "memory";
+	};
+
+	ec_input_spi: spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		num-chipselects = <0>;
+		sck-gpios = <&gpio 55 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio 57 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&usb_otg0 {
+	status = "okay";
+};
+
+&usb_otg_phy0 {
+	status = "okay";
+};
+
+&hsic0 {
+	status = "okay";
+
+	usb1@1 {
+		compatible = "usb424,2640";
+		reg = <0x01>;
+		#address-cells = <0x01>;
+		#size-cells = <0x00>;
+
+		mass-storage@1 {
+			compatible = "usb424,4040";
+			reg = <0x01>;
+			status = "disabled";
+		};
+	};
+};
+
+&hsic_phy0 {
+	status = "okay";
+	reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>;
+};
+
+&mmc3 {
+	status = "okay";
+	max-frequency = <50000000>;
+	status = "okay";
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-highspeed;
+};
+
+&twsi1 {
+	status = "okay";
+
+	rtc@68 {
+		compatible = "dallas,ds1338";
+		reg = <0x68>;
+		status = "okay";
+	};
+};
+
+&twsi3 {
+	status = "okay";
+};
+
+&twsi4 {
+	status = "okay";
+
+	embedded-controller@58 {
+		compatible = "dell,wyse-ariel-ec", "ene,kb3930";
+		reg = <0x58>;
+		system-power-controller;
+
+		off-gpios = <&gpio 126 GPIO_ACTIVE_HIGH>,
+			    <&gpio 127 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&ssp1 {
+	status = "okay";
+	cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+
+	firmware-flash@0 {
+		compatible = "winbond,w25q32", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		m25p,fast-read;
+	};
+};
+
+&ec_input_spi {
+	status = "okay";
+	cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+
+	power-button@0 {
+		reg = <0>;
+		interrupt-parent = <&gpio>;
+		interrupts = <60 IRQ_TYPE_EDGE_RISING>;
+		compatible = "dell,wyse-ariel-ec-input", "ene,kb3930-input";
+		spi-max-frequency = <33000000>;
+	};
+};
+
+&gpu_2d {
+	status = "okay";
+};
+
+&gpu_3d {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mmp3.dtsi b/arch/arm/boot/dts/marvell/mmp3.dtsi
index d9762de0ed34..a4fb9203ec1f 100644
--- a/arch/arm/boot/dts/mmp3.dtsi
+++ b/arch/arm/boot/dts/marvell/mmp3.dtsi
@@ -4,6 +4,7 @@
  */
 
 #include <dt-bindings/clock/marvell,mmp2.h>
+#include <dt-bindings/power/marvell,mmp2.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
@@ -183,14 +184,14 @@
 				mrvl,intc-nr-irqs = <5>;
 			};
 
-			usb_otg_phy0: usb-otg-phy@d4207000 {
+			usb_otg_phy0: usb-phy@d4207000 {
 				compatible = "marvell,mmp3-usb-phy";
 				reg = <0xd4207000 0x40>;
 				#phy-cells = <0>;
 				status = "disabled";
 			};
 
-			usb_otg0: usb-otg@d4208000 {
+			usb_otg0: usb@d4208000 {
 				compatible = "marvell,pxau2o-ehci";
 				reg = <0xd4208000 0x200>;
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
@@ -201,6 +202,48 @@
 				status = "disabled";
 			};
 
+			hsic_phy0: usb-phy@f0001800 {
+				compatible = "marvell,mmp3-hsic-phy";
+				reg = <0xf0001800 0x40>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			hsic0: usb@f0001000 {
+				compatible = "marvell,pxau2o-ehci";
+				reg = <0xf0001000 0x200>;
+				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&soc_clocks MMP2_CLK_USBHSIC0>;
+				clock-names = "USBCLK";
+				phys = <&hsic_phy0>;
+				phy-names = "usb";
+				phy_type = "hsic";
+				#address-cells = <0x01>;
+				#size-cells = <0x00>;
+				status = "disabled";
+			};
+
+			hsic_phy1: usb-phy@f0002800 {
+				compatible = "marvell,mmp3-hsic-phy";
+				reg = <0xf0002800 0x40>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			hsic1: usb@f0002000 {
+				compatible = "marvell,pxau2o-ehci";
+				reg = <0xf0002000 0x200>;
+				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&soc_clocks MMP2_CLK_USBHSIC1>;
+				clock-names = "USBCLK";
+				phys = <&hsic_phy1>;
+				phy-names = "usb";
+				phy_type = "hsic";
+				#address-cells = <0x01>;
+				#size-cells = <0x00>;
+				status = "disabled";
+			};
+
 			mmc1: mmc@d4280000 {
 				compatible = "mrvl,pxav3-mmc";
 				reg = <0xd4280000 0x120>;
@@ -237,12 +280,24 @@
 				status = "disabled";
 			};
 
+			mmc5: mmc@d4217000 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0xd4217000 0x120>;
+				clocks = <&soc_clocks MMP3_CLK_SDH4>;
+				clock-names = "io";
+				interrupt-parent = <&hsi1_mux>;
+				interrupts = <0>;
+				status = "disabled";
+			};
+
 			camera0: camera@d420a000 {
 				compatible = "marvell,mmp2-ccic";
 				reg = <0xd420a000 0x800>;
-				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <1>;
+				interrupt-parent = <&ci_mux>;
 				clocks = <&soc_clocks MMP2_CLK_CCIC0>;
 				clock-names = "axi";
+				power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>;
 				#clock-cells = <0>;
 				clock-output-names = "mclk";
 				status = "disabled";
@@ -251,13 +306,39 @@
 			camera1: camera@d420a800 {
 				compatible = "marvell,mmp2-ccic";
 				reg = <0xd420a800 0x800>;
-				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <2>;
+				interrupt-parent = <&ci_mux>;
 				clocks = <&soc_clocks MMP2_CLK_CCIC1>;
 				clock-names = "axi";
+				power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>;
 				#clock-cells = <0>;
 				clock-output-names = "mclk";
 				status = "disabled";
 			};
+
+			gpu_3d: gpu@d420d000 {
+				compatible = "vivante,gc";
+				reg = <0xd420d000 0x2000>;
+				interrupt-parent = <&gpu_mux>;
+				interrupts = <0>;
+				status = "disabled";
+				clocks = <&soc_clocks MMP3_CLK_GPU_3D>,
+					 <&soc_clocks MMP3_CLK_GPU_BUS>;
+				clock-names = "core", "bus";
+				power-domains = <&soc_clocks MMP2_POWER_DOMAIN_GPU>;
+			};
+
+			gpu_2d: gpu@d420f000 {
+				compatible = "vivante,gc";
+				reg = <0xd420f000 0x2000>;
+				interrupt-parent = <&gpu_mux>;
+				interrupts = <2>;
+				status = "disabled";
+				clocks = <&soc_clocks MMP3_CLK_GPU_2D>,
+					 <&soc_clocks MMP3_CLK_GPU_BUS>;
+				clock-names = "core", "bus";
+				power-domains = <&soc_clocks MMP2_POWER_DOMAIN_GPU>;
+			};
 		};
 
 		apb@d4000000 {
@@ -274,8 +355,8 @@
 				clocks = <&soc_clocks MMP2_CLK_TIMER>;
 			};
 
-			uart1: uart@d4030000 {
-				compatible = "mrvl,mmp-uart";
+			uart1: serial@d4030000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4030000 0x1000>;
 				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_UART0>;
@@ -284,8 +365,8 @@
 				status = "disabled";
 			};
 
-			uart2: uart@d4017000 {
-				compatible = "mrvl,mmp-uart";
+			uart2: serial@d4017000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4017000 0x1000>;
 				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_UART1>;
@@ -294,8 +375,8 @@
 				status = "disabled";
 			};
 
-			uart3: uart@d4018000 {
-				compatible = "mrvl,mmp-uart";
+			uart3: serial@d4018000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4018000 0x1000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_UART2>;
@@ -304,8 +385,8 @@
 				status = "disabled";
 			};
 
-			uart4: uart@d4016000 {
-				compatible = "mrvl,mmp-uart";
+			uart4: serial@d4016000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4016000 0x1000>;
 				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_UART3>;
@@ -356,7 +437,7 @@
 
 			twsi1: i2c@d4011000 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4011000 0x1000>;
+				reg = <0xd4011000 0x70>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI0>;
 				resets = <&soc_clocks MMP2_CLK_TWSI0>;
@@ -368,7 +449,7 @@
 
 			twsi2: i2c@d4031000 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4031000 0x1000>;
+				reg = <0xd4031000 0x70>;
 				interrupt-parent = <&twsi_mux>;
 				interrupts = <0>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI1>;
@@ -380,7 +461,7 @@
 
 			twsi3: i2c@d4032000 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4032000 0x1000>;
+				reg = <0xd4032000 0x70>;
 				interrupt-parent = <&twsi_mux>;
 				interrupts = <1>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI2>;
@@ -392,7 +473,7 @@
 
 			twsi4: i2c@d4033000 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4033000 0x1000>;
+				reg = <0xd4033000 0x70>;
 				interrupt-parent = <&twsi_mux>;
 				interrupts = <2>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI3>;
@@ -405,7 +486,7 @@
 
 			twsi5: i2c@d4033800 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4033800 0x1000>;
+				reg = <0xd4033800 0x70>;
 				interrupt-parent = <&twsi_mux>;
 				interrupts = <3>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI4>;
@@ -417,7 +498,7 @@
 
 			twsi6: i2c@d4034000 {
 				compatible = "mrvl,mmp-twsi";
-				reg = <0xd4034000 0x1000>;
+				reg = <0xd4034000 0x70>;
 				interrupt-parent = <&twsi_mux>;
 				interrupts = <4>;
 				clocks = <&soc_clocks MMP2_CLK_TWSI5>;
@@ -430,7 +511,7 @@
 			rtc: rtc@d4010000 {
 				compatible = "mrvl,mmp-rtc";
 				reg = <0xd4010000 0x1000>;
-				interrupts = <1 0>;
+				interrupts = <1>, <0>;
 				interrupt-names = "rtc 1Hz", "rtc alarm";
 				interrupt-parent = <&rtc_mux>;
 				clocks = <&soc_clocks MMP2_CLK_RTC>;
@@ -479,7 +560,7 @@
 			};
 		};
 
-		l2: l2-cache-controller@d0020000 {
+		l2: cache-controller@d0020000 {
 			compatible = "marvell,tauros3-cache", "arm,pl310-cache";
 			reg = <0xd0020000 0x1000>;
 			cache-unified;
@@ -487,8 +568,8 @@
 		};
 
 		soc_clocks: clocks@d4050000 {
-			compatible = "marvell,mmp2-clock";
-			reg = <0xd4050000 0x1000>,
+			compatible = "marvell,mmp3-clock";
+			reg = <0xd4050000 0x2000>,
 			      <0xd4282800 0x400>,
 			      <0xd4015000 0x1000>;
 			reg-names = "mpmu", "apmu", "apbc";
diff --git a/arch/arm/boot/dts/mvebu-linkstation-fan.dtsi b/arch/arm/boot/dts/marvell/mvebu-linkstation-fan.dtsi
index e172029a0c4d..a260c42dbda3 100644
--- a/arch/arm/boot/dts/mvebu-linkstation-fan.dtsi
+++ b/arch/arm/boot/dts/marvell/mvebu-linkstation-fan.dtsi
@@ -50,10 +50,10 @@
 		pinctrl-names = "default";
 
 		gpio-fan,speed-map =
-			<0		3
-			1500	2
-			3250	1
-			5000	0>;
+			<   0 3>,
+			<1500 2>,
+			<3250 1>,
+			<5000 0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/mvebu-linkstation-gpio-simple.dtsi b/arch/arm/boot/dts/marvell/mvebu-linkstation-gpio-simple.dtsi
index c2d87ba6190a..c2d87ba6190a 100644
--- a/arch/arm/boot/dts/mvebu-linkstation-gpio-simple.dtsi
+++ b/arch/arm/boot/dts/marvell/mvebu-linkstation-gpio-simple.dtsi
diff --git a/arch/arm/boot/dts/orion5x-kuroboxpro.dts b/arch/arm/boot/dts/marvell/orion5x-kuroboxpro.dts
index e28b568e741a..e28b568e741a 100644
--- a/arch/arm/boot/dts/orion5x-kuroboxpro.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-kuroboxpro.dts
diff --git a/arch/arm/boot/dts/orion5x-lacie-d2-network.dts b/arch/arm/boot/dts/marvell/orion5x-lacie-d2-network.dts
index 422958d13d42..03471d30bfd9 100644
--- a/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-lacie-d2-network.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/marvell/orion5x-lacie-ethernet-disk-mini-v2.dts
index 0043e0040153..f17e25ac98dd 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /*
  * TODO: add Orion USB device port init when kernel.org support is added.
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lschl.dts b/arch/arm/boot/dts/marvell/orion5x-linkstation-lschl.dts
index ee751995c8d0..ee751995c8d0 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lschl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation-lschl.dts
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lsgl.dts b/arch/arm/boot/dts/marvell/orion5x-linkstation-lsgl.dts
index 9f6fedd39170..9f6fedd39170 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lsgl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation-lsgl.dts
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts b/arch/arm/boot/dts/marvell/orion5x-linkstation-lswtgl.dts
index 7f77ce8cc1fc..7f77ce8cc1fc 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation-lswtgl.dts
diff --git a/arch/arm/boot/dts/orion5x-linkstation.dtsi b/arch/arm/boot/dts/marvell/orion5x-linkstation.dtsi
index b6c9b85951ea..b6c9b85951ea 100644
--- a/arch/arm/boot/dts/orion5x-linkstation.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation.dtsi
diff --git a/arch/arm/boot/dts/orion5x-lswsgl.dts b/arch/arm/boot/dts/marvell/orion5x-lswsgl.dts
index 2fbc17d6dfa4..2fbc17d6dfa4 100644
--- a/arch/arm/boot/dts/orion5x-lswsgl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-lswsgl.dts
diff --git a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts b/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts
index 0ca6208a267d..d57859998350 100644
--- a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/orion5x-mv88f5181.dtsi b/arch/arm/boot/dts/marvell/orion5x-mv88f5181.dtsi
index f667012b26ca..819f9efb7058 100644
--- a/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x-mv88f5181.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 #include "orion5x.dtsi"
 
diff --git a/arch/arm/boot/dts/orion5x-mv88f5182.dtsi b/arch/arm/boot/dts/marvell/orion5x-mv88f5182.dtsi
index d1ed71c60209..86b87fb26dc9 100644
--- a/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x-mv88f5182.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #include "orion5x.dtsi"
 
diff --git a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts b/arch/arm/boot/dts/marvell/orion5x-netgear-wnr854t.dts
index ea081afa469d..fb203e7d37f5 100644
--- a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-netgear-wnr854t.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 /dts-v1/;
 
@@ -142,8 +137,12 @@
 
 			port@3 {
 				reg = <3>;
-				label = "cpu";
 				ethernet = <&ethport>;
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
 			};
 
 			port@5 {
@@ -213,6 +212,7 @@
 		/* Hardwired to DSA switch */
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
diff --git a/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts b/arch/arm/boot/dts/marvell/orion5x-rd88f5182-nas.dts
index 487324f7c54e..fd78aa02a3c5 100644
--- a/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-rd88f5182-nas.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/marvell/orion5x.dtsi
index 61e631b3fd8b..2d41f5c166ee 100644
--- a/arch/arm/boot/dts/orion5x.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
 
diff --git a/arch/arm/boot/dts/pxa168-aspenite.dts b/arch/arm/boot/dts/marvell/pxa168-aspenite.dts
index 2ad40e373194..8bade6bf395b 100644
--- a/arch/arm/boot/dts/pxa168-aspenite.dts
+++ b/arch/arm/boot/dts/marvell/pxa168-aspenite.dts
@@ -18,18 +18,16 @@
 	memory {
 		reg = <0x00000000 0x04000000>;
 	};
+};
 
-	soc {
-		apb@d4000000 {
-			uart1: uart@d4017000 {
-				status = "okay";
-			};
-			twsi1: i2c@d4011000 {
-				status = "okay";
-			};
-			rtc: rtc@d4010000 {
-				status = "okay";
-			};
-		};
-	};
+&uart1 {
+	status = "okay";
+};
+
+&twsi1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
 };
diff --git a/arch/arm/boot/dts/pxa168.dtsi b/arch/arm/boot/dts/marvell/pxa168.dtsi
index 72f8cb60cb53..22ed10cb5619 100644
--- a/arch/arm/boot/dts/pxa168.dtsi
+++ b/arch/arm/boot/dts/marvell/pxa168.dtsi
@@ -53,29 +53,34 @@
 				compatible = "mrvl,mmp-timer";
 				reg = <0xd4014000 0x100>;
 				interrupts = <13>;
+				clocks = <&soc_clocks PXA168_CLK_TIMER>;
+				resets = <&soc_clocks PXA168_CLK_TIMER>;
 			};
 
-			uart1: uart@d4017000 {
-				compatible = "mrvl,mmp-uart";
+			uart1: serial@d4017000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4017000 0x1000>;
+				reg-shift = <2>;
 				interrupts = <27>;
 				clocks = <&soc_clocks PXA168_CLK_UART0>;
 				resets = <&soc_clocks PXA168_CLK_UART0>;
 				status = "disabled";
 			};
 
-			uart2: uart@d4018000 {
-				compatible = "mrvl,mmp-uart";
+			uart2: serial@d4018000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4018000 0x1000>;
+				reg-shift = <2>;
 				interrupts = <28>;
 				clocks = <&soc_clocks PXA168_CLK_UART1>;
 				resets = <&soc_clocks PXA168_CLK_UART1>;
 				status = "disabled";
 			};
 
-			uart3: uart@d4026000 {
-				compatible = "mrvl,mmp-uart";
+			uart3: serial@d4026000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4026000 0x1000>;
+				reg-shift = <2>;
 				interrupts = <29>;
 				clocks = <&soc_clocks PXA168_CLK_UART2>;
 				resets = <&soc_clocks PXA168_CLK_UART2>;
@@ -94,7 +99,7 @@
 				resets = <&soc_clocks PXA168_CLK_GPIO>;
 				interrupt-names = "gpio_mux";
 				interrupt-controller;
-				#interrupt-cells = <1>;
+				#interrupt-cells = <2>;
 				ranges;
 
 				gcb0: gpio@d4019000 {
@@ -116,6 +121,8 @@
 
 			twsi1: i2c@d4011000 {
 				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xd4011000 0x1000>;
 				interrupts = <7>;
 				clocks = <&soc_clocks PXA168_CLK_TWSI0>;
@@ -126,6 +133,8 @@
 
 			twsi2: i2c@d4025000 {
 				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xd4025000 0x1000>;
 				interrupts = <58>;
 				clocks = <&soc_clocks PXA168_CLK_TWSI1>;
@@ -136,7 +145,7 @@
 			rtc: rtc@d4010000 {
 				compatible = "mrvl,mmp-rtc";
 				reg = <0xd4010000 0x1000>;
-				interrupts = <5 6>;
+				interrupts = <5>, <6>;
 				interrupt-names = "rtc 1Hz", "rtc alarm";
 				clocks = <&soc_clocks PXA168_CLK_RTC>;
 				resets = <&soc_clocks PXA168_CLK_RTC>;
@@ -144,7 +153,7 @@
 			};
 		};
 
-		soc_clocks: clocks{
+		soc_clocks: clocks {
 			compatible = "marvell,pxa168-clock";
 			reg = <0xd4050000 0x1000>,
 			      <0xd4282800 0x400>,
diff --git a/arch/arm/boot/dts/marvell/pxa910-dkb.dts b/arch/arm/boot/dts/marvell/pxa910-dkb.dts
new file mode 100644
index 000000000000..ce76158867c7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/pxa910-dkb.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2012 Marvell Technology Group Ltd.
+ *  Author: Haojian Zhuang <haojian.zhuang@marvell.com>
+ */
+
+/dts-v1/;
+#include "pxa910.dtsi"
+
+/ {
+	model = "Marvell PXA910 DKB Development Board";
+	compatible = "mrvl,pxa910-dkb", "mrvl,pxa910";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on";
+	};
+
+	memory {
+		reg = <0x00000000 0x10000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&twsi1 {
+	status = "okay";
+
+	pmic: 88pm860x@34 {
+		compatible = "marvell,88pm860x";
+		reg = <0x34>;
+		interrupts = <4>;
+		interrupt-parent = <&intc>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		marvell,88pm860x-irq-read-clr;
+		marvell,88pm860x-slave-addr = <0x11>;
+
+		regulators {
+			BUCK1 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			BUCK2 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			BUCK3 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+			LDO5 {
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO7 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO8 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO9 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO10 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			LDO12 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+			LDO13 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+			LDO14 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+		rtc {
+			marvell,88pm860x-vrtc = <1>;
+		};
+		touch {
+			marvell,88pm860x-gpadc-prebias = <1>;
+			marvell,88pm860x-gpadc-slot-cycle = <1>;
+			marvell,88pm860x-tsi-prebias = <6>;
+			marvell,88pm860x-pen-prebias = <16>;
+			marvell,88pm860x-pen-prechg = <2>;
+			marvell,88pm860x-resistor-X = <300>;
+		};
+		backlights {
+			backlight-0 {
+				marvell,88pm860x-iset = <4>;
+				marvell,88pm860x-pwm = <3>;
+			};
+			backlight-2 {
+			};
+		};
+		leds {
+			led0-red {
+				marvell,88pm860x-iset = <12>;
+			};
+			led0-green {
+				marvell,88pm860x-iset = <12>;
+			};
+			led0-blue {
+				marvell,88pm860x-iset = <12>;
+			};
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/pxa910.dtsi b/arch/arm/boot/dts/marvell/pxa910.dtsi
index b3d6182d4de4..bd64ac1ec66f 100644
--- a/arch/arm/boot/dts/pxa910.dtsi
+++ b/arch/arm/boot/dts/marvell/pxa910.dtsi
@@ -67,27 +67,30 @@
 				status = "disabled";
 			};
 
-			uart1: uart@d4017000 {
-				compatible = "mrvl,mmp-uart";
+			uart1: serial@d4017000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4017000 0x1000>;
+				reg-shift = <2>;
 				interrupts = <27>;
 				clocks = <&soc_clocks PXA910_CLK_UART0>;
 				resets = <&soc_clocks PXA910_CLK_UART0>;
 				status = "disabled";
 			};
 
-			uart2: uart@d4018000 {
-				compatible = "mrvl,mmp-uart";
+			uart2: serial@d4018000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4018000 0x1000>;
+				reg-shift = <2>;
 				interrupts = <28>;
 				clocks = <&soc_clocks PXA910_CLK_UART1>;
 				resets = <&soc_clocks PXA910_CLK_UART1>;
 				status = "disabled";
 			};
 
-			uart3: uart@d4036000 {
-				compatible = "mrvl,mmp-uart";
+			uart3: serial@d4036000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
 				reg = <0xd4036000 0x1000>;
+				reg-shift = <2>;
 				interrupts = <59>;
 				clocks = <&soc_clocks PXA910_CLK_UART2>;
 				resets = <&soc_clocks PXA910_CLK_UART2>;
@@ -106,7 +109,7 @@
 				clocks = <&soc_clocks PXA910_CLK_GPIO>;
 				resets = <&soc_clocks PXA910_CLK_GPIO>;
 				interrupt-controller;
-				#interrupt-cells = <1>;
+				#interrupt-cells = <2>;
 				ranges;
 
 				gcb0: gpio@d4019000 {
@@ -152,7 +155,7 @@
 			rtc: rtc@d4010000 {
 				compatible = "mrvl,mmp-rtc";
 				reg = <0xd4010000 0x1000>;
-				interrupts = <5 6>;
+				interrupts = <5>, <6>;
 				interrupt-names = "rtc 1Hz", "rtc alarm";
 				clocks = <&soc_clocks PXA910_CLK_RTC>;
 				resets = <&soc_clocks PXA910_CLK_RTC>;
@@ -160,7 +163,7 @@
 			};
 		};
 
-		soc_clocks: clocks{
+		soc_clocks: clocks {
 			compatible = "marvell,pxa910-clock";
 			reg = <0xd4050000 0x1000>,
 			      <0xd4282800 0x400>,
diff --git a/arch/arm/boot/dts/mediatek/Makefile b/arch/arm/boot/dts/mediatek/Makefile
new file mode 100644
index 000000000000..1957947cb41c
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/Makefile
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MEDIATEK) += \
+	mt2701-evb.dtb \
+	mt6580-evbp1.dtb \
+	mt6582-prestigio-pmt5008-3g.dtb \
+	mt6589-aquaris5.dtb \
+	mt6589-fairphone-fp1.dtb \
+	mt6592-evb.dtb \
+	mt7623a-rfb-emmc.dtb \
+	mt7623a-rfb-nand.dtb \
+	mt7623n-rfb-emmc.dtb \
+	mt7623n-bananapi-bpi-r2.dtb \
+	mt7629-rfb.dtb \
+	mt8127-moose.dtb \
+	mt8135-evbp1.dtb
diff --git a/arch/arm/boot/dts/mt2701-evb.dts b/arch/arm/boot/dts/mediatek/mt2701-evb.dts
index 88f8fd22302a..9c7325f18933 100644
--- a/arch/arm/boot/dts/mt2701-evb.dts
+++ b/arch/arm/boot/dts/mediatek/mt2701-evb.dts
@@ -6,6 +6,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "mt2701.dtsi"
 
 / {
@@ -61,6 +62,15 @@
 		>;
 		default-brightness-level = <9>;
 	};
+
+	usb_vbus: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 45 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &auxadc {
@@ -230,3 +240,14 @@
 &uart0 {
 	status = "okay";
 };
+
+&usb2 {
+	status = "okay";
+	usb-role-switch;
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		id-gpios = <&pio 44 GPIO_ACTIVE_HIGH>;
+		vbus-supply = <&usb_vbus>;
+	};
+};
diff --git a/arch/arm/boot/dts/mt2701-pinfunc.h b/arch/arm/boot/dts/mediatek/mt2701-pinfunc.h
index 136a25a0ae28..136a25a0ae28 100644
--- a/arch/arm/boot/dts/mt2701-pinfunc.h
+++ b/arch/arm/boot/dts/mediatek/mt2701-pinfunc.h
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mediatek/mt2701.dtsi
index 51e1305c6471..ce6a4015fed5 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt2701.dtsi
@@ -148,7 +148,7 @@
 		reg = <0 0x10005000 0 0x1000>;
 	};
 
-	scpsys: scpsys@10006000 {
+	scpsys: power-controller@10006000 {
 		compatible = "mediatek,mt2701-scpsys", "syscon";
 		#power-domain-cells = <1>;
 		reg = <0 0x10006000 0 0x1000>;
@@ -178,7 +178,6 @@
 		compatible = "mediatek,mt2701-pinctrl";
 		reg = <0 0x1000b000 0 0x1000>;
 		mediatek,pctl-regmap = <&syscfg_pctl_a>;
-		pins-are-numbered;
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -360,7 +359,7 @@
 		mediatek,apmixedsys = <&apmixedsys>;
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt2701-nfc";
 		reg = <0 0x1100d000 0 0x1000>;
 		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
@@ -427,9 +426,9 @@
 
 		afe: audio-controller {
 			compatible = "mediatek,mt2701-audio";
-			interrupts =  <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
 				      <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupt-names = "afe", "asys";
 			power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
 
 			clocks = <&infracfg CLK_INFRA_AUDIO>,
@@ -559,16 +558,27 @@
 		compatible = "mediatek,mt2701-jpgdec";
 		reg = <0 0x15004000 0 0x1000>;
 		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_JPGDEC_SMI>,
+		clocks = <&imgsys CLK_IMG_JPGDEC_SMI>,
 			  <&imgsys CLK_IMG_JPGDEC>;
 		clock-names = "jpgdec-smi",
 			      "jpgdec";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
 	};
 
+	jpegenc: jpegenc@1500a000 {
+		compatible = "mediatek,mt2701-jpgenc",
+			     "mediatek,mtk-jpgenc";
+		reg = <0 0x1500a000 0 0x1000>;
+		interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&imgsys CLK_IMG_VENC>;
+		clock-names = "jpgenc";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
+		iommus = <&iommu MT2701_M4U_PORT_JPGENC_RDMA>,
+			 <&iommu MT2701_M4U_PORT_JPGENC_BSDMA>;
+	};
+
 	vdecsys: syscon@16000000 {
 		compatible = "mediatek,mt2701-vdecsys", "syscon";
 		reg = <0 0x16000000 0 0x1000>;
@@ -594,7 +604,7 @@
 	};
 
 	usb0: usb@1a1c0000 {
-		compatible = "mediatek,mt8173-xhci";
+		compatible = "mediatek,mt2701-xhci", "mediatek,mtk-xhci";
 		reg = <0 0x1a1c0000 0 0x1000>,
 		      <0 0x1a1c4700 0 0x0100>;
 		reg-names = "mac", "ippc";
@@ -607,8 +617,9 @@
 		status = "disabled";
 	};
 
-	u3phy0: usb-phy@1a1c4000 {
-		compatible = "mediatek,mt2701-u3phy";
+	u3phy0: t-phy@1a1c4000 {
+		compatible = "mediatek,mt2701-tphy",
+			     "mediatek,generic-tphy-v1";
 		reg = <0 0x1a1c4000 0 0x0700>;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -633,7 +644,7 @@
 	};
 
 	usb1: usb@1a240000 {
-		compatible = "mediatek,mt8173-xhci";
+		compatible = "mediatek,mt2701-xhci", "mediatek,mtk-xhci";
 		reg = <0 0x1a240000 0 0x1000>,
 		      <0 0x1a244700 0 0x0100>;
 		reg-names = "mac", "ippc";
@@ -646,8 +657,9 @@
 		status = "disabled";
 	};
 
-	u3phy1: usb-phy@1a244000 {
-		compatible = "mediatek,mt2701-u3phy";
+	u3phy1: t-phy@1a244000 {
+		compatible = "mediatek,mt2701-tphy",
+			     "mediatek,generic-tphy-v1";
 		reg = <0 0x1a244000 0 0x0700>;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -671,6 +683,40 @@
 		};
 	};
 
+	usb2: usb@11200000 {
+		compatible = "mediatek,mt2701-musb",
+			     "mediatek,mtk-musb";
+		reg = <0 0x11200000 0 0x1000>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "mc";
+		phys = <&u2port2 PHY_TYPE_USB2>;
+		dr_mode = "otg";
+		clocks = <&pericfg CLK_PERI_USB0>,
+			 <&pericfg CLK_PERI_USB0_MCU>,
+			 <&pericfg CLK_PERI_USB_SLV>;
+		clock-names = "main","mcu","univpll";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+		status = "disabled";
+	};
+
+	u2phy0: t-phy@11210000 {
+		compatible = "mediatek,mt2701-tphy",
+			     "mediatek,generic-tphy-v1";
+		reg = <0 0x11210000 0 0x0800>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		status = "okay";
+
+		u2port2: usb-phy@1a1c4800 {
+			reg = <0 0x11210800 0 0x0100>;
+			clocks = <&topckgen CLK_TOP_USB_PHY48M>;
+			clock-names = "ref";
+			#phy-cells = <1>;
+			status = "okay";
+		};
+	};
+
 	ethsys: syscon@1b000000 {
 		compatible = "mediatek,mt2701-ethsys", "syscon";
 		reg = <0 0x1b000000 0 0x1000>;
diff --git a/arch/arm/boot/dts/mt6323.dtsi b/arch/arm/boot/dts/mediatek/mt6323.dtsi
index 7fda40ab5fe8..c230c865116d 100644
--- a/arch/arm/boot/dts/mt6323.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6323.dtsi
@@ -21,10 +21,10 @@
 			status = "disabled";
 		};
 
-		mt6323regulator: mt6323regulator{
+		mt6323regulator: mt6323regulator {
 			compatible = "mediatek,mt6323-regulator";
 
-			mt6323_vproc_reg: buck_vproc{
+			mt6323_vproc_reg: buck_vproc {
 				regulator-name = "vproc";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -33,7 +33,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vsys_reg: buck_vsys{
+			mt6323_vsys_reg: buck_vsys {
 				regulator-name = "vsys";
 				regulator-min-microvolt = <1400000>;
 				regulator-max-microvolt = <2987500>;
@@ -42,13 +42,13 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vpa_reg: buck_vpa{
+			mt6323_vpa_reg: buck_vpa {
 				regulator-name = "vpa";
 				regulator-min-microvolt = < 500000>;
 				regulator-max-microvolt = <3650000>;
 			};
 
-			mt6323_vtcxo_reg: ldo_vtcxo{
+			mt6323_vtcxo_reg: ldo_vtcxo {
 				regulator-name = "vtcxo";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -57,28 +57,28 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcn28_reg: ldo_vcn28{
+			mt6323_vcn28_reg: ldo_vcn28 {
 				regulator-name = "vcn28";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
 				regulator-enable-ramp-delay = <185>;
 			};
 
-			mt6323_vcn33_bt_reg: ldo_vcn33_bt{
+			mt6323_vcn33_bt_reg: ldo_vcn33_bt {
 				regulator-name = "vcn33_bt";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3600000>;
 				regulator-enable-ramp-delay = <185>;
 			};
 
-			mt6323_vcn33_wifi_reg: ldo_vcn33_wifi{
+			mt6323_vcn33_wifi_reg: ldo_vcn33_wifi {
 				regulator-name = "vcn33_wifi";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3600000>;
 				regulator-enable-ramp-delay = <185>;
 			};
 
-			mt6323_va_reg: ldo_va{
+			mt6323_va_reg: ldo_va {
 				regulator-name = "va";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -87,14 +87,14 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcama_reg: ldo_vcama{
+			mt6323_vcama_reg: ldo_vcama {
 				regulator-name = "vcama";
 				regulator-min-microvolt = <1500000>;
 				regulator-max-microvolt = <2800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vio28_reg: ldo_vio28{
+			mt6323_vio28_reg: ldo_vio28 {
 				regulator-name = "vio28";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -103,7 +103,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vusb_reg: ldo_vusb{
+			mt6323_vusb_reg: ldo_vusb {
 				regulator-name = "vusb";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -111,7 +111,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vmc_reg: ldo_vmc{
+			mt6323_vmc_reg: ldo_vmc {
 				regulator-name = "vmc";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
@@ -119,7 +119,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vmch_reg: ldo_vmch{
+			mt6323_vmch_reg: ldo_vmch {
 				regulator-name = "vmch";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -127,7 +127,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vemc3v3_reg: ldo_vemc3v3{
+			mt6323_vemc3v3_reg: ldo_vemc3v3 {
 				regulator-name = "vemc3v3";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -135,49 +135,49 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vgp1_reg: ldo_vgp1{
+			mt6323_vgp1_reg: ldo_vgp1 {
 				regulator-name = "vgp1";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vgp2_reg: ldo_vgp2{
+			mt6323_vgp2_reg: ldo_vgp2 {
 				regulator-name = "vgp2";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vgp3_reg: ldo_vgp3{
+			mt6323_vgp3_reg: ldo_vgp3 {
 				regulator-name = "vgp3";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vcn18_reg: ldo_vcn18{
+			mt6323_vcn18_reg: ldo_vcn18 {
 				regulator-name = "vcn18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vsim1_reg: ldo_vsim1{
+			mt6323_vsim1_reg: ldo_vsim1 {
 				regulator-name = "vsim1";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vsim2_reg: ldo_vsim2{
+			mt6323_vsim2_reg: ldo_vsim2 {
 				regulator-name = "vsim2";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vrtc_reg: ldo_vrtc{
+			mt6323_vrtc_reg: ldo_vrtc {
 				regulator-name = "vrtc";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -185,28 +185,28 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcamaf_reg: ldo_vcamaf{
+			mt6323_vcamaf_reg: ldo_vcamaf {
 				regulator-name = "vcamaf";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vibr_reg: ldo_vibr{
+			mt6323_vibr_reg: ldo_vibr {
 				regulator-name = "vibr";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-enable-ramp-delay = <36>;
 			};
 
-			mt6323_vrf18_reg: ldo_vrf18{
+			mt6323_vrf18_reg: ldo_vrf18 {
 				regulator-name = "vrf18";
 				regulator-min-microvolt = <1825000>;
 				regulator-max-microvolt = <1825000>;
 				regulator-enable-ramp-delay = <187>;
 			};
 
-			mt6323_vm_reg: ldo_vm{
+			mt6323_vm_reg: ldo_vm {
 				regulator-name = "vm";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1800000>;
@@ -215,7 +215,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vio18_reg: ldo_vio18{
+			mt6323_vio18_reg: ldo_vio18 {
 				regulator-name = "vio18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -224,14 +224,14 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcamd_reg: ldo_vcamd{
+			mt6323_vcamd_reg: ldo_vcamd {
 				regulator-name = "vcamd";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vcamio_reg: ldo_vcamio{
+			mt6323_vcamio_reg: ldo_vcamio {
 				regulator-name = "vcamio";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
diff --git a/arch/arm/boot/dts/mt6580-evbp1.dts b/arch/arm/boot/dts/mediatek/mt6580-evbp1.dts
index 755a0774a8ee..755a0774a8ee 100644
--- a/arch/arm/boot/dts/mt6580-evbp1.dts
+++ b/arch/arm/boot/dts/mediatek/mt6580-evbp1.dts
diff --git a/arch/arm/boot/dts/mt6580.dtsi b/arch/arm/boot/dts/mediatek/mt6580.dtsi
index 9e17698c0609..9e17698c0609 100644
--- a/arch/arm/boot/dts/mt6580.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6580.dtsi
diff --git a/arch/arm/boot/dts/mediatek/mt6582-prestigio-pmt5008-3g.dts b/arch/arm/boot/dts/mediatek/mt6582-prestigio-pmt5008-3g.dts
new file mode 100644
index 000000000000..b057e037f940
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt6582-prestigio-pmt5008-3g.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Maxim Kutnij <gtk3@inbox.ru>
+ */
+
+/dts-v1/;
+#include "mt6582.dtsi"
+
+/ {
+	model = "Prestigio PMT5008 3G";
+	compatible = "prestigio,pmt5008-3g", "mediatek,mt6582";
+
+	aliases {
+		bootargs = "console=ttyS0,921600n8 earlyprintk";
+		serial0 = &uart0;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mediatek/mt6582.dtsi b/arch/arm/boot/dts/mediatek/mt6582.dtsi
new file mode 100644
index 000000000000..4263371784cd
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt6582.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Maxim Kutnij <gtk3@inbox.ru>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mediatek,mt6582";
+	interrupt-parent = <&sysirq>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+		};
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+		};
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+		};
+	};
+
+	system_clk: dummy13m {
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+		#clock-cells = <0>;
+	};
+
+	rtc_clk: dummy32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32000>;
+		#clock-cells = <0>;
+	};
+
+	uart_clk: dummy26m {
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+		#clock-cells = <0>;
+	};
+
+	timer: timer@11008000 {
+		compatible = "mediatek,mt6577-timer";
+		reg = <0x10008000 0x80>;
+		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&system_clk>, <&rtc_clk>;
+		clock-names = "system-clk", "rtc-clk";
+	};
+
+	sysirq: interrupt-controller@10200100 {
+		compatible = "mediatek,mt6582-sysirq",
+			     "mediatek,mt6577-sysirq";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		interrupt-parent = <&gic>;
+		reg = <0x10200100 0x1c>;
+	};
+
+	gic: interrupt-controller@10211000 {
+		compatible = "arm,cortex-a7-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		interrupt-parent = <&gic>;
+		reg = <0x10211000 0x1000>,
+		      <0x10212000 0x2000>,
+		      <0x10214000 0x2000>,
+		      <0x10216000 0x2000>;
+	};
+
+	uart0: serial@11002000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11002000 0x400>;
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	uart1: serial@11003000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11003000 0x400>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	uart2: serial@11004000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11004000 0x400>;
+		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	uart3: serial@11005000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11005000 0x400>;
+		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	watchdog: watchdog@10007000 {
+		compatible = "mediatek,mt6582-wdt",
+			     "mediatek,mt6589-wdt";
+		reg = <0x10007000 0x100>;
+	};
+};
diff --git a/arch/arm/boot/dts/mt6589-aquaris5.dts b/arch/arm/boot/dts/mediatek/mt6589-aquaris5.dts
index 1e7079a3b449..1e7079a3b449 100644
--- a/arch/arm/boot/dts/mt6589-aquaris5.dts
+++ b/arch/arm/boot/dts/mediatek/mt6589-aquaris5.dts
diff --git a/arch/arm/boot/dts/mediatek/mt6589-fairphone-fp1.dts b/arch/arm/boot/dts/mediatek/mt6589-fairphone-fp1.dts
new file mode 100644
index 000000000000..c952347981de
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt6589-fairphone-fp1.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+#include "mt6589.dtsi"
+
+/ {
+	model = "Fairphone 1";
+	compatible = "fairphone,fp1", "mediatek,mt6589";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&cpus {
+	/* SMP is not stable on this board, makes the kernel panic */
+	/delete-property/ enable-method;
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mt6589.dtsi b/arch/arm/boot/dts/mediatek/mt6589.dtsi
index f3ccb70c0779..c6babc8ad2ba 100644
--- a/arch/arm/boot/dts/mt6589.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6589.dtsi
@@ -14,9 +14,10 @@
 	compatible = "mediatek,mt6589";
 	interrupt-parent = <&sysirq>;
 
-	cpus {
+	cpus: cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "mediatek,mt6589-smp";
 
 		cpu@0 {
 			device_type = "cpu";
diff --git a/arch/arm/boot/dts/mt6592-evb.dts b/arch/arm/boot/dts/mediatek/mt6592-evb.dts
index 5e00c1cca2d1..5e00c1cca2d1 100644
--- a/arch/arm/boot/dts/mt6592-evb.dts
+++ b/arch/arm/boot/dts/mediatek/mt6592-evb.dts
diff --git a/arch/arm/boot/dts/mt6592.dtsi b/arch/arm/boot/dts/mediatek/mt6592.dtsi
index 3716f8db951c..3716f8db951c 100644
--- a/arch/arm/boot/dts/mt6592.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6592.dtsi
diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mediatek/mt7623.dtsi
index a79f0b6c3429..f0b4a09004b3 100644
--- a/arch/arm/boot/dts/mt7623.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt7623.dtsi
@@ -3,6 +3,7 @@
  * Copyright (c) 2017-2018 MediaTek Inc.
  * Author: John Crispin <john@phrozen.org>
  *	   Sean Wang <sean.wang@mediatek.com>
+ *	   Ryder Lee <ryder.lee@mediatek.com>
  *
  */
 
@@ -13,7 +14,6 @@
 #include <dt-bindings/power/mt2701-power.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/phy/phy.h>
-#include <dt-bindings/memory/mt2701-larb-port.h>
 #include <dt-bindings/reset/mt2701-resets.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -160,7 +160,7 @@
 
 				trips {
 					cpu_passive: cpu-passive {
-						temperature = <47000>;
+						temperature = <57000>;
 						hysteresis = <2000>;
 						type = "passive";
 					};
@@ -241,7 +241,7 @@
 	};
 
 	pericfg: syscon@10003000 {
-		compatible =  "mediatek,mt7623-pericfg",
+		compatible = "mediatek,mt7623-pericfg",
 			      "mediatek,mt2701-pericfg",
 			      "syscon";
 		reg = <0 0x10003000 0 0x1000>;
@@ -253,7 +253,6 @@
 		compatible = "mediatek,mt7623-pinctrl";
 		reg = <0 0x1000b000 0 0x1000>;
 		mediatek,pctl-regmap = <&syscfg_pctl_a>;
-		pins-are-numbered;
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -268,7 +267,7 @@
 		reg = <0 0x10005000 0 0x1000>;
 	};
 
-	scpsys: scpsys@10006000 {
+	scpsys: power-controller@10006000 {
 		compatible = "mediatek,mt7623-scpsys",
 			     "mediatek,mt2701-scpsys",
 			     "syscon";
@@ -296,17 +295,6 @@
 		clock-names = "system-clk", "rtc-clk";
 	};
 
-	smi_common: smi@1000c000 {
-		compatible = "mediatek,mt7623-smi-common",
-			     "mediatek,mt2701-smi-common";
-		reg = <0 0x1000c000 0 0x1000>;
-		clocks = <&infracfg CLK_INFRA_SMI>,
-			 <&mmsys CLK_MM_SMI_COMMON>,
-			 <&infracfg CLK_INFRA_SMI>;
-		clock-names = "apb", "smi", "async";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
-	};
-
 	pwrap: pwrap@1000d000 {
 		compatible = "mediatek,mt7623-pwrap",
 			     "mediatek,mt2701-pwrap";
@@ -338,17 +326,6 @@
 		reg = <0 0x10200100 0 0x1c>;
 	};
 
-	iommu: mmsys_iommu@10205000 {
-		compatible = "mediatek,mt7623-m4u",
-			     "mediatek,mt2701-m4u";
-		reg = <0 0x10205000 0 0x1000>;
-		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&infracfg CLK_INFRA_M4U>;
-		clock-names = "bclk";
-		mediatek,larbs = <&larb0 &larb1 &larb2>;
-		#iommu-cells = <1>;
-	};
-
 	efuse: efuse@10206000 {
 		compatible = "mediatek,mt7623-efuse",
 			     "mediatek,mt8173-efuse";
@@ -607,6 +584,39 @@
 		status = "disabled";
 	};
 
+	usb0: usb@11200000 {
+		compatible = "mediatek,mt7623-musb",
+			     "mediatek,mtk-musb";
+		reg = <0 0x11200000 0 0x1000>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "mc";
+		phys = <&u2port2 PHY_TYPE_USB2>;
+		dr_mode = "otg";
+		clocks = <&pericfg CLK_PERI_USB0>,
+			 <&pericfg CLK_PERI_USB0_MCU>,
+			 <&pericfg CLK_PERI_USB_SLV>;
+		clock-names = "main","mcu","univpll";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+		status = "disabled";
+	};
+
+	u2phy1: t-phy@11210000 {
+		compatible = "mediatek,mt7623-tphy",
+			     "mediatek,generic-tphy-v1";
+		reg = <0 0x11210000 0 0x0800>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		status = "disabled";
+
+		u2port2: usb-phy@11210800 {
+			reg = <0 0x11210800 0 0x0100>;
+			clocks = <&topckgen CLK_TOP_USB_PHY48M>;
+			clock-names = "ref";
+			#phy-cells = <1>;
+		};
+	};
+
 	audsys: clock-controller@11220000 {
 		compatible = "mediatek,mt7623-audsys",
 			     "mediatek,mt2701-audsys",
@@ -617,9 +627,9 @@
 		afe: audio-controller {
 			compatible = "mediatek,mt7623-audio",
 				     "mediatek,mt2701-audio";
-			interrupts =  <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
 				      <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupt-names = "afe", "asys";
 			power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
 
 			clocks = <&infracfg CLK_INFRA_AUDIO>,
@@ -724,70 +734,6 @@
 		status = "disabled";
 	};
 
-	g3dsys: syscon@13000000 {
-		compatible = "mediatek,mt7623-g3dsys",
-			     "mediatek,mt2701-g3dsys",
-			     "syscon";
-		reg = <0 0x13000000 0 0x200>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-	};
-
-	mmsys: syscon@14000000 {
-		compatible = "mediatek,mt7623-mmsys",
-			     "mediatek,mt2701-mmsys",
-			     "syscon";
-		reg = <0 0x14000000 0 0x1000>;
-		#clock-cells = <1>;
-	};
-
-	larb0: larb@14010000 {
-		compatible = "mediatek,mt7623-smi-larb",
-			     "mediatek,mt2701-smi-larb";
-		reg = <0 0x14010000 0 0x1000>;
-		mediatek,smi = <&smi_common>;
-		mediatek,larb-id = <0>;
-		clocks = <&mmsys CLK_MM_SMI_LARB0>,
-			 <&mmsys CLK_MM_SMI_LARB0>;
-		clock-names = "apb", "smi";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
-	};
-
-	imgsys: syscon@15000000 {
-		compatible = "mediatek,mt7623-imgsys",
-			     "mediatek,mt2701-imgsys",
-			     "syscon";
-		reg = <0 0x15000000 0 0x1000>;
-		#clock-cells = <1>;
-	};
-
-	larb2: larb@15001000 {
-		compatible = "mediatek,mt7623-smi-larb",
-			     "mediatek,mt2701-smi-larb";
-		reg = <0 0x15001000 0 0x1000>;
-		mediatek,smi = <&smi_common>;
-		mediatek,larb-id = <2>;
-		clocks = <&imgsys CLK_IMG_SMI_COMM>,
-			 <&imgsys CLK_IMG_SMI_COMM>;
-		clock-names = "apb", "smi";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-	};
-
-	jpegdec: jpegdec@15004000 {
-		compatible = "mediatek,mt7623-jpgdec",
-			     "mediatek,mt2701-jpgdec";
-		reg = <0 0x15004000 0 0x1000>;
-		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_JPGDEC_SMI>,
-			  <&imgsys CLK_IMG_JPGDEC>;
-		clock-names = "jpgdec-smi",
-			      "jpgdec";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
-		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
-			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
-	};
-
 	vdecsys: syscon@16000000 {
 		compatible = "mediatek,mt7623-vdecsys",
 			     "mediatek,mt2701-vdecsys",
@@ -796,18 +742,6 @@
 		#clock-cells = <1>;
 	};
 
-	larb1: larb@16010000 {
-		compatible = "mediatek,mt7623-smi-larb",
-			     "mediatek,mt2701-smi-larb";
-		reg = <0 0x16010000 0 0x1000>;
-		mediatek,smi = <&smi_common>;
-		mediatek,larb-id = <1>;
-		clocks = <&vdecsys CLK_VDEC_CKGEN>,
-			 <&vdecsys CLK_VDEC_LARB>;
-		clock-names = "apb", "smi";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_VDEC>;
-	};
-
 	hifsys: syscon@1a000000 {
 		compatible = "mediatek,mt7623-hifsys",
 			     "mediatek,mt2701-hifsys",
@@ -885,8 +819,9 @@
 		};
 	};
 
-	pcie0_phy: pcie-phy@1a149000 {
-		compatible = "mediatek,generic-tphy-v1";
+	pcie0_phy: t-phy@1a149000 {
+		compatible = "mediatek,mt7623-tphy",
+			     "mediatek,generic-tphy-v1";
 		reg = <0 0x1a149000 0 0x0700>;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -902,8 +837,9 @@
 		};
 	};
 
-	pcie1_phy: pcie-phy@1a14a000 {
-		compatible = "mediatek,generic-tphy-v1";
+	pcie1_phy: t-phy@1a14a000 {
+		compatible = "mediatek,mt7623-tphy",
+			     "mediatek,generic-tphy-v1";
 		reg = <0 0x1a14a000 0 0x0700>;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -921,7 +857,7 @@
 
 	usb1: usb@1a1c0000 {
 		compatible = "mediatek,mt7623-xhci",
-			     "mediatek,mt8173-xhci";
+			     "mediatek,mtk-xhci";
 		reg = <0 0x1a1c0000 0 0x1000>,
 		      <0 0x1a1c4700 0 0x0100>;
 		reg-names = "mac", "ippc";
@@ -934,9 +870,9 @@
 		status = "disabled";
 	};
 
-	u3phy1: usb-phy@1a1c4000 {
-		compatible = "mediatek,mt7623-u3phy",
-			     "mediatek,mt2701-u3phy";
+	u3phy1: t-phy@1a1c4000 {
+		compatible = "mediatek,mt7623-tphy",
+			     "mediatek,generic-tphy-v1";
 		reg = <0 0x1a1c4000 0 0x0700>;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -962,7 +898,7 @@
 
 	usb2: usb@1a240000 {
 		compatible = "mediatek,mt7623-xhci",
-			     "mediatek,mt8173-xhci";
+			     "mediatek,mtk-xhci";
 		reg = <0 0x1a240000 0 0x1000>,
 		      <0 0x1a244700 0 0x0100>;
 		reg-names = "mac", "ippc";
@@ -975,9 +911,9 @@
 		status = "disabled";
 	};
 
-	u3phy2: usb-phy@1a244000 {
-		compatible = "mediatek,mt7623-u3phy",
-			     "mediatek,mt2701-u3phy";
+	u3phy2: t-phy@1a244000 {
+		compatible = "mediatek,mt7623-tphy",
+			     "mediatek,generic-tphy-v1";
 		reg = <0 0x1a244000 0 0x0700>;
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -1044,6 +980,18 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		status = "disabled";
+
+		gmac0: mac@0 {
+			compatible = "mediatek,eth-mac";
+			reg = <0>;
+			status = "disabled";
+		};
+
+		gmac1: mac@1 {
+			compatible = "mediatek,eth-mac";
+			reg = <1>;
+			status = "disabled";
+		};
 	};
 
 	crypto: crypto@1b240000 {
diff --git a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts b/arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dts
index 13c86936d1c8..5654284bab01 100644
--- a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dts
@@ -45,13 +45,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -112,75 +112,31 @@
 	status = "okay";
 };
 
-&eth {
-	status = "okay";
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "lan0";
+		};
+
+		port@1 {
+			status = "okay";
+			label = "lan1";
+		};
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
+		port@2 {
+			status = "okay";
+			label = "lan2";
+		};
 
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
+		port@3 {
+			status = "okay";
+			label = "lan3";
 		};
-	};
 
-	mdio-bus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		switch@0 {
-			compatible = "mediatek,mt7530";
-			reg = <0>;
-			mediatek,mcm;
-			resets = <&ethsys MT2701_ETHSYS_MCM_RST>;
-			reset-names = "mcm";
-			core-supply = <&mt6323_vpa_reg>;
-			io-supply = <&mt6323_vemc3v3_reg>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					label = "lan0";
-				};
-
-				port@1 {
-					reg = <1>;
-					label = "lan1";
-				};
-
-				port@2 {
-					reg = <2>;
-					label = "lan2";
-				};
-
-				port@3 {
-					reg = <3>;
-					label = "lan3";
-				};
-
-				port@4 {
-					reg = <4>;
-					label = "wan";
-				};
-
-				port@6 {
-					reg = <6>;
-					label = "cpu";
-					ethernet = <&gmac0>;
-					phy-mode = "trgmii";
-
-					fixed-link {
-						speed = <1000>;
-						full-duplex;
-					};
-				};
-			};
+		port@4 {
+			status = "okay";
+			label = "wan";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/mt7623a-rfb-nand.dts b/arch/arm/boot/dts/mediatek/mt7623a-rfb-nand.dts
index 88d8f0b2f4c2..afd177b3b516 100644
--- a/arch/arm/boot/dts/mt7623a-rfb-nand.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623a-rfb-nand.dts
@@ -45,13 +45,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -116,75 +116,31 @@
 	status = "okay";
 };
 
-&eth {
-	status = "okay";
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "lan0";
+		};
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
+		port@1 {
+			status = "okay";
+			label = "lan1";
+		};
 
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
+		port@2 {
+			status = "okay";
+			label = "lan2";
 		};
-	};
 
-	mdio-bus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		switch@0 {
-			compatible = "mediatek,mt7530";
-			reg = <0>;
-			mediatek,mcm;
-			resets = <&ethsys MT2701_ETHSYS_MCM_RST>;
-			reset-names = "mcm";
-			core-supply = <&mt6323_vpa_reg>;
-			io-supply = <&mt6323_vemc3v3_reg>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					label = "lan0";
-				};
-
-				port@1 {
-					reg = <1>;
-					label = "lan1";
-				};
-
-				port@2 {
-					reg = <2>;
-					label = "lan2";
-				};
-
-				port@3 {
-					reg = <3>;
-					label = "lan3";
-				};
-
-				port@4 {
-					reg = <4>;
-					label = "wan";
-				};
-
-				port@6 {
-					reg = <6>;
-					label = "cpu";
-					ethernet = <&gmac0>;
-					phy-mode = "trgmii";
-
-					fixed-link {
-						speed = <1000>;
-						full-duplex;
-					};
-				};
-			};
+		port@3 {
+			status = "okay";
+			label = "lan3";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "wan";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/mediatek/mt7623a.dtsi b/arch/arm/boot/dts/mediatek/mt7623a.dtsi
new file mode 100644
index 000000000000..bcf909d58a1c
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt7623a.dtsi
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017-2018 MediaTek Inc.
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/power/mt7623a-power.h>
+#include "mt7623.dtsi"
+
+&afe {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
+};
+
+&crypto {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "trgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&eth {
+	status = "okay";
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0: switch@1f {
+			compatible = "mediatek,mt7530";
+			reg = <0x1f>;
+			mediatek,mcm;
+			resets = <&ethsys MT2701_ETHSYS_MCM_RST>;
+			reset-names = "mcm";
+			core-supply = <&mt6323_vpa_reg>;
+			io-supply = <&mt6323_vemc3v3_reg>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					status = "disabled";
+					reg = <0>;
+					label = "swp0";
+				};
+
+				port@1 {
+					status = "disabled";
+					reg = <1>;
+					label = "swp1";
+				};
+
+				port@2 {
+					status = "disabled";
+					reg = <2>;
+					label = "swp2";
+				};
+
+				port@3 {
+					status = "disabled";
+					reg = <3>;
+					label = "swp3";
+				};
+
+				port@4 {
+					status = "disabled";
+					reg = <4>;
+					label = "swp4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "trgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+&nandc {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
+};
+
+&pcie {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
+};
+
+&scpsys {
+	compatible = "mediatek,mt7623a-scpsys";
+	clocks = <&topckgen CLK_TOP_ETHIF_SEL>;
+	clock-names = "ethif";
+};
+
+&usb0 {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
+};
+
+&usb1 {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
+};
+
+&usb2 {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
+};
diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mediatek/mt7623n-bananapi-bpi-r2.dts
index 2b760f90f38c..a37f3fa223c7 100644
--- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623n-bananapi-bpi-r2.dts
@@ -6,7 +6,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/input.h>
-#include "mt7623.dtsi"
+#include "mt7623n.dtsi"
 #include "mt6323.dtsi"
 
 / {
@@ -21,6 +21,19 @@
 		stdout-path = "serial2:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "d";
+		ddc-i2c-bus = <&hdmiddc0>;
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi0_out>;
+			};
+		};
+	};
+
 	cpus {
 		cpu@0 {
 			proc-supply = <&mt6323_vproc_reg>;
@@ -66,18 +79,25 @@
 		regulator-always-on;
 	};
 
+	reg_vgpu: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_fixed_vgpu";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -114,10 +134,18 @@
 	};
 };
 
+&bls {
+	status = "okay";
+};
+
 &btif {
 	status = "okay";
 };
 
+&cec {
+	status = "okay";
+};
+
 &cir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cir_pins_a>;
@@ -128,28 +156,53 @@
 	status = "okay";
 };
 
-&eth {
+&dpi0 {
 	status = "okay";
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
-
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+			dpi0_out: endpoint {
+				remote-endpoint = <&hdmi0_in>;
+			};
 		};
 	};
+};
 
-	mdio: mdio-bus {
+&gmac0 {
+	status = "okay";
+	phy-mode = "trgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	mdio-bus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		switch@0 {
+		switch@1f {
 			compatible = "mediatek,mt7530";
-			reg = <0>;
+			reg = <0x1f>;
 			reset-gpios = <&pio 33 0>;
 			core-supply = <&mt6323_vpa_reg>;
 			io-supply = <&mt6323_vemc3v3_reg>;
@@ -183,6 +236,19 @@
 					label = "lan3";
 				};
 
+				port@5 {
+					reg = <5>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+
 				port@6 {
 					reg = <6>;
 					label = "cpu";
@@ -192,6 +258,7 @@
 					fixed-link {
 						speed = <1000>;
 						full-duplex;
+						pause;
 					};
 				};
 			};
@@ -199,6 +266,42 @@
 	};
 };
 
+&hdmi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_pins_a>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+			hdmi0_in: endpoint {
+				remote-endpoint = <&dpi0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi_connector_in>;
+			};
+		};
+	};
+};
+
+&hdmiddc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_ddc_pins_a>;
+	status = "okay";
+};
+
+&hdmi_phy {
+	mediatek,ibias = <0xa>;
+	mediatek,ibias_up = <0x1c>;
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins_a>;
@@ -211,6 +314,11 @@
 	status = "okay";
 };
 
+&mali {
+	mali-supply = <&reg_vgpu>;
+	status = "okay";
+};
+
 &mmc0 {
 	pinctrl-names = "default", "state_uhs";
 	pinctrl-0 = <&mmc0_pins_default>;
@@ -237,6 +345,12 @@
 	vqmmc-supply = <&reg_3p3v>;
 };
 
+&mt6323keys {
+	home {
+		status = "disabled";
+	};
+};
+
 &mt6323_leds {
 	status = "okay";
 
@@ -281,6 +395,14 @@
 	status = "okay";
 };
 
+&pio {
+	musb_pins: musb {
+		pins-musb {
+			pinmux = <MT7623_PIN_237_EXT_SDIO2_FUNC_DRV_VBUS>;
+		};
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm_pins_a>;
@@ -311,6 +433,19 @@
 	status = "okay";
 };
 
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&musb_pins>;
+	status = "okay";
+	usb-role-switch;
+
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		id-gpios = <&pio 44 GPIO_ACTIVE_HIGH>;
+	};
+};
+
 &usb1 {
 	vusb33-supply = <&reg_3p3v>;
 	vbus-supply = <&reg_5v>;
@@ -323,6 +458,10 @@
 	status = "okay";
 };
 
+&u2phy1 {
+	status = "okay";
+};
+
 &u3phy1 {
 	status = "okay";
 };
@@ -330,4 +469,3 @@
 &u3phy2 {
 	status = "okay";
 };
-
diff --git a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts b/arch/arm/boot/dts/mediatek/mt7623n-rfb-emmc.dts
index b7606130ade9..34994f3f5a4b 100644
--- a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623n-rfb-emmc.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/input.h>
-#include "mt7623.dtsi"
+#include "mt7623n.dtsi"
 #include "mt6323.dtsi"
 
 / {
@@ -24,6 +24,19 @@
 		stdout-path = "serial2:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "d";
+		ddc-i2c-bus = <&hdmiddc0>;
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi0_out>;
+			};
+		};
+	};
+
 	cpus {
 		cpu@0 {
 			proc-supply = <&mt6323_vproc_reg>;
@@ -47,13 +60,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -106,10 +119,18 @@
 	};
 };
 
+&bls {
+	status = "okay";
+};
+
 &btif {
 	status = "okay";
 };
 
+&cec {
+	status = "okay";
+};
+
 &cir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cir_pins_a>;
@@ -120,26 +141,40 @@
 	status = "okay";
 };
 
-&eth {
+&dpi0 {
 	status = "okay";
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
-
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+			dpi0_out: endpoint {
+				remote-endpoint = <&hdmi0_in>;
+			};
 		};
 	};
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "trgmii";
 
-	mac@1 {
-		compatible = "mediatek,eth-mac";
-		reg = <1>;
-		phy-handle = <&phy5>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
 	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&phy5>;
+};
+
+&eth {
+	status = "okay";
 
 	mdio-bus {
 		#address-cells = <1>;
@@ -150,9 +185,9 @@
 			phy-mode = "rgmii-rxid";
 		};
 
-		switch@0 {
+		switch@1f {
 			compatible = "mediatek,mt7530";
-			reg = <0>;
+			reg = <0x1f>;
 			reset-gpios = <&pio 33 0>;
 			core-supply = <&mt6323_vpa_reg>;
 			io-supply = <&mt6323_vemc3v3_reg>;
@@ -195,6 +230,7 @@
 					fixed-link {
 						speed = <1000>;
 						full-duplex;
+						pause;
 					};
 				};
 			};
@@ -202,6 +238,42 @@
 	};
 };
 
+&hdmi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_pins_a>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+			hdmi0_in: endpoint {
+				remote-endpoint = <&dpi0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi_connector_in>;
+			};
+		};
+	};
+};
+
+&hdmiddc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_ddc_pins_a>;
+	status = "okay";
+};
+
+&hdmi_phy {
+	mediatek,ibias = <0xa>;
+	mediatek,ibias_up = <0x1c>;
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins_a>;
diff --git a/arch/arm/boot/dts/mediatek/mt7623n.dtsi b/arch/arm/boot/dts/mediatek/mt7623n.dtsi
new file mode 100644
index 000000000000..3e5cabf19cde
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt7623n.dtsi
@@ -0,0 +1,301 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright © 2017-2020 MediaTek Inc.
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ *	   Ryder Lee <ryder.lee@mediatek.com>
+ *
+ */
+
+#include "mt7623.dtsi"
+#include <dt-bindings/memory/mt2701-larb-port.h>
+
+/ {
+	aliases {
+		rdma0 = &rdma0;
+		rdma1 = &rdma1;
+	};
+
+	g3dsys: syscon@13000000 {
+		compatible = "mediatek,mt7623-g3dsys",
+			     "mediatek,mt2701-g3dsys",
+			     "syscon";
+		reg = <0 0x13000000 0 0x200>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+	mali: gpu@13040000 {
+		compatible = "mediatek,mt7623-mali", "arm,mali-450";
+		reg = <0 0x13040000 0 0x30000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 171 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 172 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 173 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 174 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 175 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 176 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 177 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 178 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 179 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pp1",
+				  "ppmmu1", "pp2", "ppmmu2", "pp3", "ppmmu3",
+				  "pp";
+		clocks = <&topckgen CLK_TOP_MMPLL>,
+			 <&g3dsys CLK_G3DSYS_CORE>;
+		clock-names = "bus", "core";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_MFG>;
+		resets = <&g3dsys MT2701_G3DSYS_CORE_RST>;
+	};
+
+	mmsys: syscon@14000000 {
+		compatible = "mediatek,mt7623-mmsys",
+			     "mediatek,mt2701-mmsys",
+			     "syscon";
+		reg = <0 0x14000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	larb0: larb@14010000 {
+		compatible = "mediatek,mt7623-smi-larb",
+			     "mediatek,mt2701-smi-larb";
+		reg = <0 0x14010000 0 0x1000>;
+		mediatek,smi = <&smi_common>;
+		mediatek,larb-id = <0>;
+		clocks = <&mmsys CLK_MM_SMI_LARB0>,
+			 <&mmsys CLK_MM_SMI_LARB0>;
+		clock-names = "apb", "smi";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
+	};
+
+	larb1: larb@16010000 {
+		compatible = "mediatek,mt7623-smi-larb",
+			     "mediatek,mt2701-smi-larb";
+		reg = <0 0x16010000 0 0x1000>;
+		mediatek,smi = <&smi_common>;
+		mediatek,larb-id = <1>;
+		clocks = <&vdecsys CLK_VDEC_CKGEN>,
+			 <&vdecsys CLK_VDEC_LARB>;
+		clock-names = "apb", "smi";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_VDEC>;
+	};
+
+	larb2: larb@15001000 {
+		compatible = "mediatek,mt7623-smi-larb",
+			     "mediatek,mt2701-smi-larb";
+		reg = <0 0x15001000 0 0x1000>;
+		mediatek,smi = <&smi_common>;
+		mediatek,larb-id = <2>;
+		clocks = <&imgsys CLK_IMG_SMI_COMM>,
+			 <&imgsys CLK_IMG_SMI_COMM>;
+		clock-names = "apb", "smi";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
+	};
+
+	imgsys: syscon@15000000 {
+		compatible = "mediatek,mt7623-imgsys",
+			     "mediatek,mt2701-imgsys",
+			     "syscon";
+		reg = <0 0x15000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	iommu: mmsys_iommu@10205000 {
+		compatible = "mediatek,mt7623-m4u",
+			     "mediatek,mt2701-m4u";
+		reg = <0 0x10205000 0 0x1000>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&infracfg CLK_INFRA_M4U>;
+		clock-names = "bclk";
+		mediatek,larbs = <&larb0 &larb1 &larb2>;
+		#iommu-cells = <1>;
+	};
+
+	jpegdec: jpegdec@15004000 {
+		compatible = "mediatek,mt7623-jpgdec",
+			     "mediatek,mt2701-jpgdec";
+		reg = <0 0x15004000 0 0x1000>;
+		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&imgsys CLK_IMG_JPGDEC_SMI>,
+			 <&imgsys CLK_IMG_JPGDEC>;
+		clock-names = "jpgdec-smi",
+			      "jpgdec";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
+		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
+			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
+	};
+
+	smi_common: smi@1000c000 {
+		compatible = "mediatek,mt7623-smi-common",
+			     "mediatek,mt2701-smi-common";
+		reg = <0 0x1000c000 0 0x1000>;
+		clocks = <&infracfg CLK_INFRA_SMI>,
+			 <&mmsys CLK_MM_SMI_COMMON>,
+			 <&infracfg CLK_INFRA_SMI>;
+		clock-names = "apb", "smi", "async";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
+	};
+
+	ovl: ovl@14007000 {
+		compatible = "mediatek,mt7623-disp-ovl",
+			     "mediatek,mt2701-disp-ovl";
+		reg = <0 0x14007000 0 0x1000>;
+		interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DISP_OVL>;
+		iommus = <&iommu MT2701_M4U_PORT_DISP_OVL_0>;
+	};
+
+	rdma0: rdma@14008000 {
+		compatible = "mediatek,mt7623-disp-rdma",
+			     "mediatek,mt2701-disp-rdma";
+		reg = <0 0x14008000 0 0x1000>;
+		interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DISP_RDMA>;
+		iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA>;
+	};
+
+	wdma@14009000 {
+		compatible = "mediatek,mt7623-disp-wdma",
+			     "mediatek,mt2701-disp-wdma";
+		reg = <0 0x14009000 0 0x1000>;
+		interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DISP_WDMA>;
+		iommus = <&iommu MT2701_M4U_PORT_DISP_WDMA>;
+	};
+
+	bls: pwm@1400a000 {
+		compatible = "mediatek,mt7623-disp-pwm",
+			     "mediatek,mt2701-disp-pwm";
+		reg = <0 0x1400a000 0 0x1000>;
+		#pwm-cells = <2>;
+		clocks = <&mmsys CLK_MM_MDP_BLS_26M>,
+			 <&mmsys CLK_MM_DISP_BLS>;
+		clock-names = "main", "mm";
+		status = "disabled";
+	};
+
+	color: color@1400b000 {
+		compatible = "mediatek,mt7623-disp-color",
+			     "mediatek,mt2701-disp-color";
+		reg = <0 0x1400b000 0 0x1000>;
+		interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DISP_COLOR>;
+	};
+
+	dsi: dsi@1400c000 {
+		compatible = "mediatek,mt7623-dsi",
+			     "mediatek,mt2701-dsi";
+		reg = <0 0x1400c000 0 0x1000>;
+		interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DSI_ENGINE>,
+			 <&mmsys CLK_MM_DSI_DIG>,
+			 <&mipi_tx0>;
+		clock-names = "engine", "digital", "hs";
+		phys = <&mipi_tx0>;
+		phy-names = "dphy";
+		status = "disabled";
+	};
+
+	mutex: mutex@1400e000 {
+		compatible = "mediatek,mt7623-disp-mutex",
+			     "mediatek,mt2701-disp-mutex";
+		reg = <0 0x1400e000 0 0x1000>;
+		interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_MUTEX_32K>;
+	};
+
+	rdma1: rdma@14012000 {
+		compatible = "mediatek,mt7623-disp-rdma",
+			     "mediatek,mt2701-disp-rdma";
+		reg = <0 0x14012000 0 0x1000>;
+		interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DISP_RDMA1>;
+		iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA1>;
+	};
+
+	dpi0: dpi@14014000 {
+		compatible = "mediatek,mt7623-dpi",
+			     "mediatek,mt2701-dpi";
+		reg = <0 0x14014000 0 0x1000>;
+		interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&mmsys CLK_MM_DPI1_DIGL>,
+			 <&mmsys CLK_MM_DPI1_ENGINE>,
+			 <&apmixedsys CLK_APMIXED_TVDPLL>;
+		clock-names = "pixel", "engine", "pll";
+		status = "disabled";
+	};
+
+	hdmi0: hdmi@14015000 {
+		compatible = "mediatek,mt7623-hdmi",
+			     "mediatek,mt2701-hdmi";
+		reg = <0 0x14015000 0 0x400>;
+		clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
+			 <&mmsys CLK_MM_HDMI_PLL>,
+			 <&mmsys CLK_MM_HDMI_AUDIO>,
+			 <&mmsys CLK_MM_HDMI_SPDIF>;
+		clock-names = "pixel", "pll", "bclk", "spdif";
+		phys = <&hdmi_phy>;
+		phy-names = "hdmi";
+		mediatek,syscon-hdmi = <&mmsys 0x900>;
+		cec = <&cec>;
+		status = "disabled";
+	};
+
+	mipi_tx0: dsi-phy@10010000 {
+		compatible = "mediatek,mt7623-mipi-tx",
+			     "mediatek,mt2701-mipi-tx";
+		reg = <0 0x10010000 0 0x90>;
+		clocks = <&clk26m>;
+		clock-output-names = "mipi_tx0_pll";
+		#clock-cells = <0>;
+		#phy-cells = <0>;
+	};
+
+	cec: cec@10012000 {
+		compatible = "mediatek,mt7623-cec",
+			     "mediatek,mt8173-cec";
+		reg = <0 0x10012000 0 0xbc>;
+		interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&infracfg CLK_INFRA_CEC>;
+		status = "disabled";
+	};
+
+	hdmi_phy: hdmi-phy@10209100 {
+		compatible = "mediatek,mt7623-hdmi-phy",
+			     "mediatek,mt2701-hdmi-phy";
+		reg = <0 0x10209100 0 0x24>;
+		clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
+		clock-names = "pll_ref";
+		clock-output-names = "hdmitx_dig_cts";
+		#clock-cells = <0>;
+		#phy-cells = <0>;
+		status = "disabled";
+	};
+
+	hdmiddc0: i2c@11013000 {
+		compatible = "mediatek,mt7623-hdmi-ddc",
+			     "mediatek,mt8173-hdmi-ddc";
+		interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
+		reg = <0 0x11013000 0 0x1C>;
+		clocks = <&pericfg CLK_PERI_I2C3>;
+		clock-names = "ddc-i2c";
+		status = "disabled";
+	};
+};
+
+&pio {
+	hdmi_pins_a: hdmi-default {
+		pins-hdmi {
+			pinmux = <MT7623_PIN_123_HTPLG_FUNC_HTPLG>;
+			input-enable;
+			bias-pull-down;
+		};
+	};
+
+	hdmi_ddc_pins_a: hdmi_ddc-default {
+		pins-hdmi-ddc {
+			pinmux = <MT7623_PIN_124_GPIO124_FUNC_HDMISCK>,
+				 <MT7623_PIN_125_GPIO125_FUNC_HDMISD>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/mt7629-rfb.dts b/arch/arm/boot/dts/mediatek/mt7629-rfb.dts
index 9980c10c6e29..f24ebc20732a 100644
--- a/arch/arm/boot/dts/mt7629-rfb.dts
+++ b/arch/arm/boot/dts/mediatek/mt7629-rfb.dts
@@ -23,13 +23,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		reset {
+		button-reset {
 			label = "factory";
 			linux,code = <KEY_RESTART>;
 			gpios = <&pio 60 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 58 GPIO_ACTIVE_LOW>;
@@ -140,9 +140,10 @@
 	};
 };
 
-&pcie {
+&pcie1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
 };
 
 &pciephy1 {
@@ -167,7 +168,7 @@
 	i2c_pins: i2c-pins {
 		mux {
 			function = "i2c";
-			groups =  "i2c_0";
+			groups = "i2c_0";
 		};
 
 		conf {
diff --git a/arch/arm/boot/dts/mt7629.dtsi b/arch/arm/boot/dts/mediatek/mt7629.dtsi
index 867b88103b9d..acab0883a3bb 100644
--- a/arch/arm/boot/dts/mt7629.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt7629.dtsi
@@ -90,7 +90,7 @@
 			#clock-cells = <1>;
 		};
 
-		scpsys: scpsys@10006000 {
+		scpsys: power-controller@10006000 {
 			compatible = "mediatek,mt7629-scpsys",
 				     "mediatek,mt7622-scpsys";
 			#power-domain-cells = <1>;
@@ -106,8 +106,7 @@
 			compatible = "mediatek,mt7629-timer",
 				     "mediatek,mt6765-timer";
 			reg = <0x10009000 0x60>;
-			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk20m>;
 			clock-names = "clk20m";
 		};
@@ -241,6 +240,20 @@
 			status = "disabled";
 		};
 
+		pwm: pwm@11006000 {
+			compatible = "mediatek,mt7629-pwm";
+			reg = <0x11006000 0x1000>;
+			#pwm-cells = <2>;
+			clocks = <&topckgen CLK_TOP_PWM_SEL>,
+				 <&pericfg CLK_PERI_PWM_PD>,
+				 <&pericfg CLK_PERI_PWM1_PD>;
+			clock-names = "top", "main", "pwm1";
+			assigned-clocks = <&topckgen CLK_TOP_PWM_SEL>;
+			assigned-clock-parents =
+					<&topckgen CLK_TOP_UNIVPLL2_D4>;
+			status = "disabled";
+		};
+
 		i2c: i2c@11007000 {
 			compatible = "mediatek,mt7629-i2c",
 				     "mediatek,mt2712-i2c";
@@ -315,8 +328,9 @@
 			status = "disabled";
 		};
 
-		u3phy0: usb-phy@1a0c4000 {
-			compatible = "mediatek,generic-tphy-v2";
+		u3phy0: t-phy@1a0c4000 {
+			compatible = "mediatek,mt7629-tphy",
+				     "mediatek,generic-tphy-v2";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x1a0c4000 0xe00>;
@@ -346,16 +360,21 @@
 			#reset-cells = <1>;
 		};
 
-		pcie: pcie@1a140000 {
+		pciecfg: pciecfg@1a140000 {
+			compatible = "mediatek,generic-pciecfg", "syscon";
+			reg = <0x1a140000 0x1000>;
+		};
+
+		pcie1: pcie@1a145000 {
 			compatible = "mediatek,mt7629-pcie";
 			device_type = "pci";
-			reg = <0x1a140000 0x1000>,
-			      <0x1a145000 0x1000>;
-			reg-names = "subsys","port1";
+			reg = <0x1a145000 0x1000>;
+			reg-names = "port1";
+			linux,pci-domain = <1>;
 			#address-cells = <3>;
 			#size-cells = <2>;
-			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_LOW>,
-				     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-names = "pcie_irq";
 			clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
 				 <&pciesys CLK_PCIE_P0_AHB_EN>,
 				 <&pciesys CLK_PCIE_P1_AUX_EN>,
@@ -376,37 +395,30 @@
 			power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
 			bus-range = <0x00 0xff>;
 			ranges = <0x82000000 0 0x20000000 0x20000000 0 0x10000000>;
+			status = "disabled";
 
-			pcie1: pcie@1,0 {
-				device_type = "pci";
-				reg = <0x0800 0 0 0 0>;
-				#address-cells = <3>;
-				#size-cells = <2>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+					<0 0 0 2 &pcie_intc1 1>,
+					<0 0 0 3 &pcie_intc1 2>,
+					<0 0 0 4 &pcie_intc1 3>;
+			pcie_intc1: interrupt-controller {
+				interrupt-controller;
+				#address-cells = <0>;
 				#interrupt-cells = <1>;
-				ranges;
-				num-lanes = <1>;
-				interrupt-map-mask = <0 0 0 7>;
-				interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-						<0 0 0 2 &pcie_intc1 1>,
-						<0 0 0 3 &pcie_intc1 2>,
-						<0 0 0 4 &pcie_intc1 3>;
-
-				pcie_intc1: interrupt-controller {
-					interrupt-controller;
-					#address-cells = <0>;
-					#interrupt-cells = <1>;
-				};
 			};
 		};
 
-		pciephy1: pcie-phy@1a14a000 {
-			compatible = "mediatek,generic-tphy-v2";
+		pciephy1: t-phy@1a14a000 {
+			compatible = "mediatek,mt7629-tphy",
+				     "mediatek,generic-tphy-v2";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x1a14a000 0x1000>;
 			status = "disabled";
 
-			pcieport1: port1phy@0 {
+			pcieport1: pcie-phy@0 {
 				reg = <0 0x1000>;
 				clocks = <&clk20m>;
 				clock-names = "ref";
diff --git a/arch/arm/boot/dts/mt8127-moose.dts b/arch/arm/boot/dts/mediatek/mt8127-moose.dts
index 560687af87dc..560687af87dc 100644
--- a/arch/arm/boot/dts/mt8127-moose.dts
+++ b/arch/arm/boot/dts/mediatek/mt8127-moose.dts
diff --git a/arch/arm/boot/dts/mt8127.dtsi b/arch/arm/boot/dts/mediatek/mt8127.dtsi
index aced173c2a52..aced173c2a52 100644
--- a/arch/arm/boot/dts/mt8127.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt8127.dtsi
diff --git a/arch/arm/boot/dts/mt8135-evbp1.dts b/arch/arm/boot/dts/mediatek/mt8135-evbp1.dts
index f6147fe62f41..f6147fe62f41 100644
--- a/arch/arm/boot/dts/mt8135-evbp1.dts
+++ b/arch/arm/boot/dts/mediatek/mt8135-evbp1.dts
diff --git a/arch/arm/boot/dts/mt8135.dtsi b/arch/arm/boot/dts/mediatek/mt8135.dtsi
index 0e4e835026db..0f291ad22d3a 100644
--- a/arch/arm/boot/dts/mt8135.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt8135.dtsi
@@ -9,7 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/reset/mt8135-resets.h>
-#include "mt8135-pinfunc.h"
+#include <dt-bindings/pinctrl/mt8135-pinfunc.h>
 
 / {
 	#address-cells = <2>;
@@ -152,7 +152,6 @@
 			compatible = "mediatek,mt8135-pinctrl";
 			reg = <0 0x1000b000 0 0x1000>;
 			mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
-			pins-are-numbered;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile
new file mode 100644
index 000000000000..efde9546c8f4
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/Makefile
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: GPL-2.0
+# Enables support for device-tree overlays
+DTC_FLAGS_at91-sam9x60_curiosity := -@
+DTC_FLAGS_at91-sam9x60ek := -@
+DTC_FLAGS_at91-sama5d27_som1_ek := -@
+DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@
+DTC_FLAGS_at91-sama5d29_curiosity := -@
+DTC_FLAGS_at91-sama5d2_icp := -@
+DTC_FLAGS_at91-sama5d2_ptc_ek := -@
+DTC_FLAGS_at91-sama5d2_xplained := -@
+DTC_FLAGS_at91-sama5d3_eds := -@
+DTC_FLAGS_at91-sama5d3_xplained := -@
+DTC_FLAGS_at91-sama5d4_xplained := -@
+DTC_FLAGS_at91-sama7g5ek := -@
+dtb-$(CONFIG_SOC_AT91RM9200) += \
+	at91rm9200ek.dtb \
+	mpa1600.dtb
+dtb-$(CONFIG_SOC_AT91SAM9) += \
+	animeo_ip.dtb \
+	at91-qil_a9260.dtb \
+	aks-cdu.dtb \
+	ethernut5.dtb \
+	evk-pro3.dtb \
+	tny_a9260.dtb \
+	usb_a9260.dtb \
+	at91sam9260ek.dtb \
+	at91sam9261ek.dtb \
+	at91sam9263ek.dtb \
+	at91-sam9_l9260.dtb \
+	tny_a9263.dtb \
+	usb_a9263.dtb \
+	at91-foxg20.dtb \
+	at91-kizbox.dtb \
+	at91-lmu5000.dtb \
+	at91sam9g20ek.dtb \
+	at91sam9g20ek_2mmc.dtb \
+	tny_a9g20.dtb \
+	usb_a9g20.dtb \
+	usb_a9g20_lpw.dtb \
+	at91sam9m10g45ek.dtb \
+	pm9g45.dtb \
+	at91sam9n12ek.dtb \
+	at91sam9rlek.dtb \
+	at91-ariag25.dtb \
+	at91-ariettag25.dtb \
+	at91-cosino_mega2560.dtb \
+	at91-kizboxmini-base.dtb \
+	at91-kizboxmini-mb.dtb \
+	at91-kizboxmini-rd.dtb \
+	at91-q5xr5.dtb \
+	at91-smartkiz.dtb \
+	at91-wb45n.dtb \
+	at91sam9g15ek.dtb \
+	at91sam9g25-gardena-smart-gateway.dtb \
+	at91sam9g25ek.dtb \
+	at91sam9g35ek.dtb \
+	at91sam9x25ek.dtb \
+	at91sam9x35ek.dtb
+dtb-$(CONFIG_SOC_SAM9X60) += \
+	at91-sam9x60_curiosity.dtb \
+	at91-sam9x60ek.dtb
+dtb-$(CONFIG_SOC_SAM_V7) += \
+	at91-kizbox2-2.dtb \
+	at91-kizbox3-hs.dtb \
+	at91-nattis-2-natte-2.dtb \
+	at91-sama5d27_som1_ek.dtb \
+	at91-sama5d27_wlsom1_ek.dtb \
+	at91-sama5d29_curiosity.dtb \
+	at91-sama5d2_icp.dtb \
+	at91-sama5d2_ptc_ek.dtb \
+	at91-sama5d2_xplained.dtb \
+	at91-sama5d3_eds.dtb \
+	at91-sama5d3_ksz9477_evb.dtb \
+	at91-sama5d3_xplained.dtb \
+	at91-dvk_som60.dtb \
+	at91-gatwick.dtb \
+	at91-tse850-3.dtb \
+	at91-wb50n.dtb \
+	sama5d31ek.dtb \
+	sama5d33ek.dtb \
+	sama5d34ek.dtb \
+	sama5d35ek.dtb \
+	sama5d36ek.dtb \
+	sama5d36ek_cmp.dtb \
+	at91-sama5d4_ma5d4evk.dtb \
+	at91-sama5d4_xplained.dtb \
+	at91-sama5d4ek.dtb \
+	at91-vinco.dtb
+dtb-$(CONFIG_SOC_SAMA7G5) += \
+	at91-sama7g5ek.dtb
+
+dtb-$(CONFIG_SOC_LAN966) += \
+	lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb \
+	lan966x-kontron-kswitch-d10-mmt-8g.dtb \
+	lan966x-pcb8290.dtb \
+	lan966x-pcb8291.dtb \
+	lan966x-pcb8309.dtb
diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/microchip/aks-cdu.dts
index 742fcf525e1b..742fcf525e1b 100644
--- a/arch/arm/boot/dts/aks-cdu.dts
+++ b/arch/arm/boot/dts/microchip/aks-cdu.dts
diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/microchip/animeo_ip.dts
index c36d28c295d6..29936bfbeeb7 100644
--- a/arch/arm/boot/dts/animeo_ip.dts
+++ b/arch/arm/boot/dts/microchip/animeo_ip.dts
@@ -26,7 +26,7 @@
 		stdout-path = &usart2;
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -81,6 +81,7 @@
 				pinctrl-0 = <&pinctrl_mmc0_clk
 					     &pinctrl_mmc0_slot1_cmd_dat0
 					     &pinctrl_mmc0_slot1_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 
 				slot@1 {
@@ -167,26 +168,24 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		keyswitch_in {
+		key-switch-in {
 			label = "keyswitch_in";
 			gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <28>;
 			wakeup-source;
 		};
 
-		error_in {
+		key-error-in {
 			label = "error_in";
 			gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <29>;
 			wakeup-source;
 		};
 
-		btn {
+		key-s {
 			label = "btn";
 			gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
 			linux,code = <31>;
diff --git a/arch/arm/boot/dts/at91-ariag25.dts b/arch/arm/boot/dts/microchip/at91-ariag25.dts
index dbfefef2869d..713d18f80356 100644
--- a/arch/arm/boot/dts/at91-ariag25.dts
+++ b/arch/arm/boot/dts/microchip/at91-ariag25.dts
@@ -22,7 +22,7 @@
 		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
 	};
 
-	memory {
+	memory@20000000 {
 		/* 128 MB, change this for 256 MB revision */
 		reg = <0x20000000 0x8000000>;
 	};
@@ -93,6 +93,7 @@
 	pinctrl-0 = <
 		&pinctrl_mmc0_slot0_clk_cmd_dat0
 		&pinctrl_mmc0_slot0_dat1_3>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	slot@0 {
diff --git a/arch/arm/boot/dts/at91-ariettag25.dts b/arch/arm/boot/dts/microchip/at91-ariettag25.dts
index 0267e72c074a..2c52a71752c2 100644
--- a/arch/arm/boot/dts/at91-ariettag25.dts
+++ b/arch/arm/boot/dts/microchip/at91-ariettag25.dts
@@ -15,7 +15,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x8000000>;
 	};
 
@@ -48,6 +48,7 @@
 	pinctrl-0 = <
 		&pinctrl_mmc0_slot0_clk_cmd_dat0
 		&pinctrl_mmc0_slot0_dat1_3>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	slot@0 {
diff --git a/arch/arm/boot/dts/at91-cosino.dtsi b/arch/arm/boot/dts/microchip/at91-cosino.dtsi
index feebd54f670e..ee0f5da6d819 100644
--- a/arch/arm/boot/dts/at91-cosino.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-cosino.dtsi
@@ -20,7 +20,7 @@
 		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x8000000>;
 	};
 
@@ -112,6 +112,7 @@
 		&pinctrl_board_mmc0
 		&pinctrl_mmc0_slot0_clk_cmd_dat0
 		&pinctrl_mmc0_slot0_dat1_3>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	slot@0 {
diff --git a/arch/arm/boot/dts/at91-cosino_mega2560.dts b/arch/arm/boot/dts/microchip/at91-cosino_mega2560.dts
index 73e88d1ba4ed..04cb7bee937d 100644
--- a/arch/arm/boot/dts/at91-cosino_mega2560.dts
+++ b/arch/arm/boot/dts/microchip/at91-cosino_mega2560.dts
@@ -34,6 +34,7 @@
 	pinctrl-0 = <
 		&pinctrl_mmc1_slot0_clk_cmd_dat0
 		&pinctrl_mmc1_slot0_dat1_3>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	slot@0 {
diff --git a/arch/arm/boot/dts/at91-dvk_som60.dts b/arch/arm/boot/dts/microchip/at91-dvk_som60.dts
index ededd5b0d27b..ededd5b0d27b 100644
--- a/arch/arm/boot/dts/at91-dvk_som60.dts
+++ b/arch/arm/boot/dts/microchip/at91-dvk_som60.dts
diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc.dtsi
index 21876da7c442..3542ad8a243e 100644
--- a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc.dtsi
@@ -44,7 +44,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25u4035", "jedec,spi-nor";
 		spi-max-frequency = <33000000>;
 		reg = <0>;
@@ -62,7 +62,7 @@
 	wm8904: wm8904@1a {
 		compatible = "wlf,wm8904";
 		reg = <0x1a>;
-		clocks = <&pck2>;
+		clocks = <&pmc PMC_TYPE_SYSTEM 10>;
 		clock-names = "mclk";
 	};
 };
diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc_lcm.dtsi
index df0f0cc575c1..bea920b192b6 100644
--- a/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc_lcm.dtsi
@@ -17,7 +17,7 @@
 	};
 
 	panel: panel {
-		compatible = "winstar,wf70gtiagdng0", "innolux,at070tn92", "simple-panel";
+		compatible = "winstar,wf70gtiagdng0", "innolux,at070tn92";
 		backlight = <&backlight>;
 		power-supply = <&vcc_lcd_reg>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/at91-foxg20.dts b/arch/arm/boot/dts/microchip/at91-foxg20.dts
index 683b9e37f9c5..9dfd5de808d1 100644
--- a/arch/arm/boot/dts/at91-foxg20.dts
+++ b/arch/arm/boot/dts/microchip/at91-foxg20.dts
@@ -17,7 +17,7 @@
 		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -55,6 +55,7 @@
 					&pinctrl_mmc0_clk
 					&pinctrl_mmc0_slot1_cmd_dat0
 					&pinctrl_mmc0_slot1_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 
 				slot@1 {
@@ -154,10 +155,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn {
+		button {
 			label = "Button";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
diff --git a/arch/arm/boot/dts/at91-gatwick.dts b/arch/arm/boot/dts/microchip/at91-gatwick.dts
index 5a81cab5fc3a..551300fd7746 100644
--- a/arch/arm/boot/dts/at91-gatwick.dts
+++ b/arch/arm/boot/dts/microchip/at91-gatwick.dts
@@ -13,7 +13,7 @@
 	model = "Laird Workgroup Bridge 50N - Project Gatwick";
 	compatible = "laird,gatwick", "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
 
@@ -31,37 +31,37 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ethernet {
+		led-ethernet {
 			label = "gatwick:yellow:ethernet";
 			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		wifi {
+		led-wifi {
 			label = "gatwick:green:wifi";
 			gpios = <&pioA 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		ble {
+		led-ble {
 			label = "gatwick:blue:ble";
 			gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		lora {
+		led-lora {
 			label = "gatwick:orange:lora";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		blank {
+		led-blank {
 			label = "gatwick:green:blank";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		user {
+		led-user {
 			label = "gatwick:yellow:user";
 			gpios = <&pioA 12 GPIO_ACTIVE_LOW>;
 			default-state = "off";
diff --git a/arch/arm/boot/dts/microchip/at91-kizbox.dts b/arch/arm/boot/dts/microchip/at91-kizbox.dts
new file mode 100644
index 000000000000..307663b4eec2
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-kizbox.dts
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * at91-kizbox.dts - Device Tree file for Overkiz Kizbox board
+ *
+ * Copyright (C) 2012-2014 Boris BREZILLON <b.brezillon@overkiz.com>
+ *               2014-2015 Gaël PORTAY <g.portay@overkiz.com>
+ */
+/dts-v1/;
+#include "at91sam9g20.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Overkiz Kizbox";
+	compatible = "overkiz,kizbox", "atmel,at91sam9g20", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "ubi.mtd=ubi";
+		stdout-path = &dbgu;
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x2000000>;
+	};
+
+	clocks {
+		main_xtal {
+			clock-frequency = <18432000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			label = "PB_RST";
+			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x100>;
+			wakeup-source;
+		};
+
+		button-user {
+			label = "PB_USER";
+			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x101>;
+			wakeup-source;
+		};
+	};
+
+	led-controller {
+		compatible = "pwm-leds";
+
+		led-1 {
+			label = "pwm:green:network";
+			pwms = <&tcb1_pwm1 0 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2 {
+			label = "pwm:red:network";
+			pwms = <&tcb1_pwm2 0 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-3 {
+			label = "pwm:green:user";
+			pwms = <&tcb1_pwm0 0 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-4 {
+			label = "pwm:red:user";
+			pwms = <&tcb1_pwm0 1 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+	};
+};
+
+&tcb0 {
+	timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>, <1>;
+	};
+
+	timer@2 {
+		compatible = "atmel,tcb-timer";
+		reg = <2>;
+	};
+};
+
+&tcb1 {
+	tcb1_pwm0: pwm@0 {
+		compatible = "atmel,tcb-pwm";
+		reg = <0>;
+		#pwm-cells = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tcb1_tioa0 &pinctrl_tcb1_tiob0>;
+	};
+
+	tcb1_pwm1: pwm@1 {
+		compatible = "atmel,tcb-pwm";
+		reg = <1>;
+		#pwm-cells = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tcb1_tioa1>;
+	};
+
+	tcb1_pwm2: pwm@2 {
+		compatible = "atmel,tcb-pwm";
+		reg = <2>;
+		#pwm-cells = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tcb1_tioa2>;
+	};
+};
+
+&ebi {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+	pinctrl-names = "default";
+
+	nand@3 {
+		reg = <0x3 0x0 0x800000>;
+		rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "soft";
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "mii";
+	pinctrl-0 = <&pinctrl_macb_rmii
+		     &pinctrl_macb_rmii_mii_alt>;
+	status = "okay";
+};
+
+&usart3 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&watchdog {
+	timeout-sec = <15>;
+	atmel,max-heartbeat-sec = <16>;
+	atmel,min-heartbeat-sec = <0>;
+	status = "okay";
+};
+
+&usb0 {
+	num-ports = <1>;
+	status = "okay";
+};
+
+&i2c_gpio0 {
+	status = "okay";
+
+	rtc: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
diff --git a/arch/arm/boot/dts/at91-kizbox2-2.dts b/arch/arm/boot/dts/microchip/at91-kizbox2-2.dts
index cab8b3579efa..cab8b3579efa 100644
--- a/arch/arm/boot/dts/at91-kizbox2-2.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizbox2-2.dts
diff --git a/arch/arm/boot/dts/at91-kizbox2-common.dtsi b/arch/arm/boot/dts/microchip/at91-kizbox2-common.dtsi
index af38253a6e7a..e5e21dff882f 100644
--- a/arch/arm/boot/dts/at91-kizbox2-common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-kizbox2-common.dtsi
@@ -17,7 +17,7 @@
 		stdout-path = &dbgu;
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x10000000>;
 	};
 
@@ -31,26 +31,24 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		prog {
+		button-prog {
 			label = "PB_PROG";
 			gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		reset {
+		button-reset {
 			label = "PB_RST";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
 			wakeup-source;
 		};
 
-		user {
+		button-user {
 			label = "PB_USER";
 			gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
@@ -58,24 +56,24 @@
 		};
 	};
 
-	pwm_leds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		blue {
+		led-1 {
 			label = "pwm:blue:user";
 			pwms = <&pwm0 2 10000000 0>;
 			max-brightness = <255>;
 			linux,default-trigger = "none";
 		};
 
-		green {
+		led-2 {
 			label = "pwm:green:user";
 			pwms = <&pwm0 1 10000000 0>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};
 
-		red {
+		led-3 {
 			label = "pwm:red:user";
 			pwms = <&pwm0 0 10000000 0>;
 			max-brightness = <255>;
diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
index 8734e7f8939e..fec7269088d1 100644
--- a/arch/arm/boot/dts/at91-kizbox3-hs.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
@@ -15,47 +15,47 @@
 	model = "Overkiz KIZBOX3-HS";
 	compatible = "overkiz,kizbox3-hs", "atmel,sama5d2", "atmel,sama5";
 
-	pwm_leds {
+	led-controller-1 {
 		status = "okay";
 
-		red {
+		led-1 {
 			status = "okay";
 		};
 
-		green {
+		led-2 {
 			status = "okay";
 		};
 
-		blue {
+		led-3 {
 			status = "okay";
 		};
 
-		white {
+		led-4 {
 			status = "okay";
 		};
 	};
 
-	leds  {
+	led-controller-2  {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led_red
 			     &pinctrl_led_white>;
 		status = "okay";
 
-		red {
+		led-5 {
 			label = "pio:red:user";
 			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		white {
+		led-6 {
 			label = "pio:white:user";
 			gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default" , "default", "default",
 				"default", "default" ;
@@ -68,35 +68,35 @@
 			     &pinctrl_pio_zbe_rst>;
 		pinctrl-4 = <&pinctrl_pio_input>;
 
-		SW1 {
+		switch-1 {
 			label = "SW1";
 			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x101>;
 			wakeup-source;
 		};
 
-		SW2 {
+		switch-2 {
 			label = "SW2";
 			gpios = <&pioA PIN_PA18 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		SW3 {
+		switch-3 {
 			label = "SW3";
 			gpios = <&pioA PIN_PA22 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		SW7 {
+		switch-7 {
 			label = "SW7";
 			gpios = <&pioA PIN_PA26 GPIO_ACTIVE_LOW>;
 			linux,code = <0x107>;
 			wakeup-source;
 		};
 
-		SW8 {
+		switch-8 {
 			label = "SW8";
 			gpios = <&pioA PIN_PA24 GPIO_ACTIVE_LOW>;
 			linux,code = <0x108>;
@@ -186,7 +186,7 @@
 
 &pioA {
 	pinctrl_key_gpio_default: key_gpio_default {
-		pinmux=  <PIN_PA22__GPIO>,
+		pinmux = <PIN_PA22__GPIO>,
 		<PIN_PA24__GPIO>,
 		<PIN_PA26__GPIO>,
 		<PIN_PA29__GPIO>,
@@ -225,7 +225,7 @@
 		pinctrl_pio_io_reset: gpio_io_reset {
 			pinmux = <PIN_PB30__GPIO>;
 			bias-disable;
-			drive-open-drain = <1>;
+			drive-open-drain;
 			output-low;
 		};
 		pinctrl_pio_input: gpio_input {
@@ -283,7 +283,7 @@
 
 &flx3 {
 	status = "okay";
-	uart6: serial@200 {
+	uart8: serial@200 {
 		status = "okay";
 	};
 };
@@ -291,7 +291,7 @@
 &flx4 {
 	status = "okay";
 
-	i2c2: i2c@600 {
+	i2c6: i2c@600 {
 		status = "okay";
 	};
 };
diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
index 299e74d23184..465664628419 100644
--- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
@@ -28,7 +28,7 @@
 		serial3 = &uart3;
 		serial4 = &uart4;
 		serial5 = &uart5;
-		serial6 = &uart6;
+		serial6 = &uart8;
 	};
 
 	chosen {
@@ -62,7 +62,7 @@
 		regulator-always-on;
 	};
 
-	pwm_leds {
+	led-controller-1 {
 		compatible = "pwm-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pwm0_pwm_h0
@@ -71,7 +71,7 @@
 			     &pinctrl_pwm0_pwm_h3>;
 		status = "disabled";
 
-		red {
+		led-1 {
 			label = "pwm:red:user";
 			pwms = <&pwm0 0 10000000 0>;
 			max-brightness = <255>;
@@ -79,7 +79,7 @@
 			status = "disabled";
 		};
 
-		green {
+		led-2 {
 			label = "pwm:green:user";
 			pwms = <&pwm0 1 10000000 0>;
 			max-brightness = <255>;
@@ -87,14 +87,14 @@
 			status = "disabled";
 		};
 
-		blue {
+		led-3 {
 			label = "pwm:blue:user";
 			pwms = <&pwm0 2 10000000 0>;
 			max-brightness = <255>;
 			status = "disabled";
 		};
 
-		white {
+		led-4 {
 			label = "pwm:white:user";
 			pwms = <&pwm0 3 10000000 0>;
 			max-brightness = <255>;
@@ -207,11 +207,11 @@
 		};
 	};
 
-	pinctrl_flx4_default: flx4_i2c2_default {
+	pinctrl_flx4_default: flx4_i2c6_default {
 		pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA
 		<PIN_PD13__FLEXCOM4_IO1>; //CLK
 		bias-disable;
-		drive-open-drain = <1>;
+		drive-open-drain;
 	};
 
 	pinctrl_pwm0 {
@@ -299,21 +299,8 @@
 	status = "disabled";
 
 	uart5: serial@200  {
-		compatible = "atmel,at91sam9260-usart";
-		reg = <0x200 0x400>;
-		interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
-		dmas = <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(11))>,
-		       <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(12))>;
-		dma-names = "tx", "rx";
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
-		clock-names = "usart";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx0_default>;
-		atmel,fifo-size = <32>;
 		atmel,use-dma-rx;
 		atmel,use-dma-tx;
 		status = "disabled";
@@ -324,22 +311,9 @@
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
 	status = "disabled";
 
-	uart6: serial@200 {
-		compatible = "atmel,at91sam9260-usart";
-		reg = <0x200 0x400>;
-		interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-		dmas = <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(17))>,
-		       <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(18))>;
-		dma-names = "tx", "rx";
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-		clock-names = "usart";
+	uart8: serial@200 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx3_default>;
-		atmel,fifo-size = <32>;
 		atmel,use-dma-rx;
 		atmel,use-dma-tx;
 		status = "disabled";
@@ -350,23 +324,9 @@
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
 	status = "disabled";
 
-	i2c2: i2c@600 {
-		compatible = "atmel,sama5d2-i2c";
-		reg = <0x600 0x200>;
-		interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
-		dmas = <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(19))>,
-		       <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(20))>;
-		dma-names = "tx", "rx";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+	i2c6: i2c@600 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx4_default>;
-		atmel,fifo-size = <16>;
 		status = "disabled";
 	};
 };
@@ -376,12 +336,11 @@
 };
 
 &shutdown_controller {
-	atmel,shdwc-debouncer = <976>;
+	debounce-delay-us = <976>;
 	atmel,wakeup-rtc-timer;
 
 	input@0 {
 		reg = <0>;
-		atmel,wakeup-type = "low";
 	};
 };
 
diff --git a/arch/arm/boot/dts/microchip/at91-kizboxmini-base.dts b/arch/arm/boot/dts/microchip/at91-kizboxmini-base.dts
new file mode 100644
index 000000000000..81c29ca5cc1b
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-base.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * at91-kizboxmini-base.dts - Device Tree file for Overkiz Kizbox mini
+ * base board
+ *
+ * Copyright (C) 2015 Overkiz SAS
+ *   Author: Antoine Aubert <a.aubert@overkiz.com>
+ *           Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+	model = "Overkiz Kizbox Mini";
+	compatible = "overkiz,kizboxmini-base", "atmel,at91sam9g25",
+		     "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&pinctrl_usart0 {
+	atmel,pins =
+		<AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+		 AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE
+		 AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+};
diff --git a/arch/arm/boot/dts/microchip/at91-kizboxmini-common.dtsi b/arch/arm/boot/dts/microchip/at91-kizboxmini-common.dtsi
new file mode 100644
index 000000000000..42640fe6b6d0
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-common.dtsi
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
+ *
+ * Copyright (C) 2014-2018 Overkiz SAS
+ *   Author: Antoine Aubert <a.aubert@overkiz.com>
+ *           Gaël Portay <g.portay@overkiz.com>
+ *           Kévin Raymond <k.raymond@overkiz.com>
+ *           Dorian Rocipon <d.rocipon@overkiz.com>
+ */
+#include "at91sam9g25.dtsi"
+
+/ {
+	chosen {
+		bootargs = "ubi.mtd=ubi";
+		stdout-path = &dbgu;
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		adc_op_clk {
+			status = "disabled";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		key-prog {
+			label = "PB_PROG";
+			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
+			linux,code = <0x102>;
+			wakeup-source;
+		};
+
+		key-reset {
+			label = "PB_RST";
+			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
+			linux,code = <0x100>;
+			wakeup-source;
+		};
+	};
+
+	leds: led-controller-1 {
+		compatible = "pwm-leds";
+
+		led_blue: led-1 {
+			label = "pwm:blue:user";
+			pwms = <&pwm0 2 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "none";
+			status = "disabled";
+		};
+
+		led_green: led-2 {
+			label = "pwm:green:user";
+			pwms = <&pwm0 0 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		led_red: led-3 {
+			label = "pwm:red:user";
+			pwms = <&pwm0 1 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+	};
+};
+
+&usart0 {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&macb0 {
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_pwm0_1
+		     &pinctrl_pwm0_pwm1_1
+		     &pinctrl_pwm0_pwm2_1>;
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&adc0 {
+	status = "disabled";
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_addr_nand
+			&pinctrl_ebi_data_0_7>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_nand_oe_we
+		     &pinctrl_nand_cs
+		     &pinctrl_nand_rb>;
+	pinctrl-names = "default";
+
+	nand@3 {
+		reg = <0x3 0x0 0x800000>;
+		rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	num-ports = <1>;
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/microchip/at91-kizboxmini-mb.dts b/arch/arm/boot/dts/microchip/at91-kizboxmini-mb.dts
new file mode 100644
index 000000000000..c07d3076a9bc
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-mb.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2018 Overkiz SAS
+ *   Author: Mickael Gardet <m.gardet@overkiz.com>
+ *           Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+	model = "Overkiz Kizbox Mini Mother Board";
+	compatible = "overkiz,kizboxmini-mb", "atmel,at91sam9g25",
+		     "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&usb0 {
+	num-ports = <2>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&led_blue {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/at91-kizboxmini-rd.dts b/arch/arm/boot/dts/microchip/at91-kizboxmini-rd.dts
new file mode 100644
index 000000000000..ab50f4d22387
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-rd.dts
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2018 Overkiz SAS
+ *   Author: Mickael Gardet <m.gardet@overkiz.com>
+ *           Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+	model = "Overkiz Kizbox Mini RailDIN";
+	compatible = "overkiz,kizboxmini-rd", "atmel,at91sam9g25",
+		     "atmel,at91sam9x5", "atmel,at91sam9";
+
+	clocks {
+		adc_op_clk {
+			status = "okay";
+		};
+	};
+};
+
+&pinctrl {
+	adc0 {
+		pinctrl_adc0_ad5: adc0_ad5-0 {
+			/* pull-up disable */
+			atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+};
+
+&usart0 {
+	status = "disabled";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&led_blue {
+	status = "okay";
+};
+
+&adc0 {
+	atmel,adc-vref = <2500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_ad5>;
+	atmel,adc-channels-used = <0x0020>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/microchip/at91-linea.dtsi
index 41f163955b1e..533a440d5583 100644
--- a/arch/arm/boot/dts/at91-linea.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-linea.dtsi
@@ -13,7 +13,7 @@
 	compatible = "axentia,linea",
 		     "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 };
diff --git a/arch/arm/boot/dts/microchip/at91-lmu5000.dts b/arch/arm/boot/dts/microchip/at91-lmu5000.dts
new file mode 100644
index 000000000000..f8863d7c0798
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-lmu5000.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree file for CalAmp LMU5000 board
+ *
+ * Copyright (C) 2013 Adam Porter <porter.adam@gmail.com>
+ */
+
+/dts-v1/;
+#include "at91sam9g20.dtsi"
+
+/ {
+	model = "CalAmp LMU5000";
+	compatible = "calamp,lmu5000", "atmel,at91sam9g20", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "mem=64M console=ttyS0,115200 rootfstype=jffs2";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+	};
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	status = "okay";
+
+	nand_controller: nand-controller {
+		pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+			status = "okay";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				kernel@0 {
+					label = "kernel";
+					reg = <0x0 0x400000>;
+				};
+
+				rootfs@400000 {
+					label = "rootfs";
+					reg = <0x400000 0x3C00000>;
+				};
+
+				user1@4000000 {
+					label = "user1";
+					reg = <0x4000000 0x2000000>;
+				};
+
+				user2@6000000 {
+					label = "user2";
+					reg = <0x6000000 0x2000000>;
+				};
+			};
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&pinctrl {
+	board {
+		pinctrl_pck0_as_mck: pck0_as_mck {
+			atmel,pins = <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	usb0 {
+		pinctrl_usb1_vbus_gpio: usb0_vbus_gpio {
+			atmel,pins = <AT91_PIOC 5 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+};
+
+&ssc0 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_ssc0_tx>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usart0 {
+	pinctrl-0 =
+		<&pinctrl_usart0
+		 &pinctrl_usart0_rts
+		 &pinctrl_usart0_cts
+		 &pinctrl_usart0_dtr_dsr
+		 &pinctrl_usart0_dcd
+		 &pinctrl_usart0_ri>;
+	status = "okay";
+};
+
+&usart2 {
+	status = "okay";
+};
+
+&usb0 {
+	num-ports = <2>;
+	status = "okay";
+};
+
+&usb1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_vbus_gpio>;
+	atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-natte.dtsi b/arch/arm/boot/dts/microchip/at91-natte.dtsi
index 49f0a0c46cde..49f0a0c46cde 100644
--- a/arch/arm/boot/dts/at91-natte.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-natte.dtsi
diff --git a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts b/arch/arm/boot/dts/microchip/at91-nattis-2-natte-2.dts
index f245944bd5d7..f71377c9b757 100644
--- a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
+++ b/arch/arm/boot/dts/microchip/at91-nattis-2-natte-2.dts
@@ -8,7 +8,6 @@
  */
 /dts-v1/;
 #include "at91-linea.dtsi"
-#include "sama5d3_lcd.dtsi"
 #include "at91-natte.dtsi"
 
 / {
@@ -19,7 +18,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "Wakeup";
 			linux,code = <10>;
 			wakeup-source;
diff --git a/arch/arm/boot/dts/microchip/at91-q5xr5.dts b/arch/arm/boot/dts/microchip/at91-q5xr5.dts
new file mode 100644
index 000000000000..9cf60b6f695c
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-q5xr5.dts
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree file for Exegin Q5xR5 board
+ *
+ * Copyright (C) 2014 Owen Kirby <osk@exegin.com>
+ */
+
+/dts-v1/;
+#include "at91sam9g20.dtsi"
+
+/ {
+	model = "Exegin Q5x (rev5)";
+	compatible = "exegin,q5xr5", "atmel,at91sam9g20", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 rootfstype=squashfs,jffs2";
+	};
+
+	memory {
+		reg = <0x20000000 0x0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <18432000>;
+		};
+	};
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "cfi-flash";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x1000000 0x800000>;
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			kernel@0 {
+				label = "kernel";
+				reg = <0x0 0x200000>;
+			};
+
+			rootfs@200000 {
+				label = "rootfs";
+				reg = <0x200000 0x600000>;
+			};
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&pinctrl {
+	board {
+		pinctrl_pck0_as_mck: pck0_as_mck {
+			atmel,pins = <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	spi0 {
+		pinctrl_spi0: spi0-0 {
+			atmel,pins =
+				<AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi0_npcs0: spi0_npcs0 {
+			atmel,pins = <AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi0_npcs1: spi0_npcs1 {
+			atmel,pins = <AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	spi1 {
+		pinctrl_spi1: spi1-0 {
+			atmel,pins =
+				<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi1_npcs0: spi1_npcs0 {
+			atmel,pins = <AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi1_npcs1: spi1_npcs1 {
+			atmel,pins = <AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0 &pinctrl_spi0_npcs0 &pinctrl_spi0_npcs1>;
+	cs-gpios = <&pioA 3 GPIO_ACTIVE_HIGH>, <&pioC 11 GPIO_ACTIVE_LOW>, <0>, <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		at91boot@0 {
+			label = "at91boot";
+			reg = <0x0 0x4000>;
+		};
+
+		uenv@4000 {
+			label = "uboot-env";
+			reg = <0x4000 0x4000>;
+		};
+
+		uboot@8000 {
+			label = "uboot";
+			reg = <0x8000 0x3E000>;
+		};
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1 &pinctrl_spi1_npcs0 &pinctrl_spi1_npcs1>;
+	cs-gpios = <&pioB 3 GPIO_ACTIVE_HIGH>, <&pioC 5 GPIO_ACTIVE_LOW>, <0>, <0>;
+	status = "okay";
+};
+
+&usart0 {
+	pinctrl-0 =
+		<&pinctrl_usart0
+		 &pinctrl_usart0_rts
+		 &pinctrl_usart0_cts
+		 &pinctrl_usart0_dtr_dsr
+		 &pinctrl_usart0_dcd
+		 &pinctrl_usart0_ri>;
+	status = "okay";
+};
+
+&usb0 {
+	num-ports = <2>;
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-qil_a9260.dts b/arch/arm/boot/dts/microchip/at91-qil_a9260.dts
index a50b7fd2149f..5ccb3c139592 100644
--- a/arch/arm/boot/dts/at91-qil_a9260.dts
+++ b/arch/arm/boot/dts/microchip/at91-qil_a9260.dts
@@ -14,7 +14,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -52,6 +52,7 @@
 					&pinctrl_mmc0_clk
 					&pinctrl_mmc0_slot0_cmd_dat0
 					&pinctrl_mmc0_slot0_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@0 {
 					reg = <0>;
@@ -107,7 +108,7 @@
 				status = "okay";
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
@@ -197,10 +198,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		user_pb {
+		button-user {
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91-sam9_l9260.dts b/arch/arm/boot/dts/microchip/at91-sam9_l9260.dts
index 954404ed8158..2fb51b9aca2a 100644
--- a/arch/arm/boot/dts/at91-sam9_l9260.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9_l9260.dts
@@ -15,7 +15,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -49,6 +49,7 @@
 					&pinctrl_mmc0_clk
 					&pinctrl_mmc0_slot1_cmd_dat0
 					&pinctrl_mmc0_slot1_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 
 				slot@1 {
@@ -100,7 +101,7 @@
 		nand0: nand@40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "soft";
-			nand-on-flash-bbt = <1>;
+			nand-on-flash-bbt;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
new file mode 100644
index 000000000000..c6fbdd29019f
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
@@ -0,0 +1,510 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x60_curiosity.dts - Device Tree file for Microchip SAM9X60 Curiosity board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Durai Manickam KR <durai.manickamkr@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x60.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Microchip SAM9X60 Curiosity";
+	compatible = "microchip,sam9x60-curiosity", "microchip,sam9x60", "atmel,at91sam9";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c6;
+		serial2 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-user {
+			label = "PB_USER";
+			gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-red {
+			label = "red";
+			gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioD 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	vdd_1v8: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "VDD_1V8";
+	};
+
+	vdd_1v15: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <1150000>;
+		regulator-min-microvolt = <1150000>;
+		regulator-name = "VDD_1V15";
+	};
+
+	vdd1_3v3: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD1_3V3";
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd1_3v3>;
+	vref-supply = <&vdd1_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_rx_tx>;
+	status = "disabled"; /* Conflict with dbgu. */
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_rx_tx>;
+	status = "okay";
+};
+
+&dbgu {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu>;
+	status = "okay"; /* Conflict with can0. */
+};
+
+&ebi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_lsb>;
+	status = "okay";
+
+	nand_controller: nand-controller {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <8>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				uboot@40000 {
+					label = "u-boot";
+					reg = <0x40000 0xc0000>;
+				};
+
+				ubootenvred@100000 {
+					label = "U-Boot Env Redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				ubootenv@140000 {
+					label = "U-Boot Env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x1f800000>;
+				};
+			};
+		};
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c0: i2c@600 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		eeprom@53 {
+			compatible = "atmel,24c02";
+			reg = <0x53>;
+			pagesize = <16>;
+		};
+	};
+};
+
+&flx6 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c6: i2c@600 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx6_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "disabled";
+	};
+};
+
+&flx7 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart7: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx7_default>;
+		status = "okay";
+	};
+};
+
+&macb0 {
+	phy-mode = "rmii";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_macb0_rmii>;
+	status = "okay";
+
+	ethernet-phy@0 {
+		reg = <0x0>;
+		interrupt-parent = <&pioB>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl {
+	adc {
+		pinctrl_adc_default: adc-default {
+			atmel,pins = <AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_adtrg_default: adtrg-default {
+			atmel,pins = <AT91_PIOB 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	can0 {
+		pinctrl_can0_rx_tx: can0-rx-tx {
+			atmel,pins =
+				<AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX0 */
+				 AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANTX0 */
+				 AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>;	/* Enable CAN Transceivers */
+		};
+	};
+
+	can1 {
+		pinctrl_can1_rx_tx: can1-rx-tx {
+			atmel,pins =
+				<AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX1 */
+				 AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANTX1 */
+				 AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>;	/* Enable CAN Transceivers */
+		};
+	};
+
+	dbgu {
+		pinctrl_dbgu: dbgu-0 {
+			atmel,pins = <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				      AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+	};
+
+	ebi {
+		pinctrl_ebi_data_lsb: ebi-data-lsb {
+			atmel,pins =
+				<AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_ebi_addr_nand: ebi-addr-nand {
+			atmel,pins =
+				<AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+	};
+
+	flexcom {
+		pinctrl_flx0_default: flx0-twi {
+			atmel,pins =
+				<AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_flx6_default: flx6-twi {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_flx7_default: flx7-usart {
+			atmel,pins =
+				<AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+				 AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+		};
+	};
+
+	gpio-keys {
+		pinctrl_key_gpio_default: pinctrl-key-gpio {
+			atmel,pins = <AT91_PIOA 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	leds {
+		pinctrl_gpio_leds: gpio-leds {
+			atmel,pins = <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	macb0 {
+		pinctrl_macb0_rmii: macb0-rmii-0 {
+			atmel,pins =
+				<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB0 periph A */
+				 AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB1 periph A */
+				 AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB2 periph A */
+				 AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB3 periph A */
+				 AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB4 periph A */
+				 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB5 periph A */
+				 AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB6 periph A */
+				 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB7 periph A */
+				 AT91_PIOB 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE	/* PB8 IRQ GPIO */
+				 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB9 periph A */
+				 AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PB10 periph A */
+		};
+	};
+
+	nand {
+		pinctrl_nand_oe_we: nand-oe-we-0 {
+			atmel,pins =
+				<AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_nand_rb: nand-rb-0 {
+			atmel,pins =
+				<AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_nand_cs: nand-cs-0 {
+			atmel,pins =
+				<AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	pwm0 {
+		pinctrl_pwm0_0: pwm0-0 {
+			atmel,pins = <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_1: pwm0-1 {
+			atmel,pins = <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_2: pwm0-2 {
+			atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc0 {
+		pinctrl_sdmmc0_default: sdmmc0 {
+			atmel,pins =
+				<AT91_PIOA 17 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI)				/* PA17 CK  periph A with pullup */
+				 AT91_PIOA 16 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA16 CMD periph A with pullup */
+				 AT91_PIOA 15 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA15 DAT0 periph A */
+				 AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA18 DAT1 periph A with pullup */
+				 AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA19 DAT2 periph A with pullup */
+				 AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>;	/* PA20 DAT3 periph A with pullup */
+		};
+
+		pinctrl_sdmmc0_cd: sdmmc0-cd {
+			atmel,pins =
+				<AT91_PIOA 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc1 {
+		pinctrl_sdmmc1_default: sdmmc1 {
+			atmel,pins =
+				<AT91_PIOA 13 AT91_PERIPH_B (AT91_PINCTRL_DRIVE_STRENGTH_HI)				/* PA13 CK periph B */
+				 AT91_PIOA 12 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA12 CMD periph B with pullup */
+				 AT91_PIOA 11 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA11 DAT0 periph B with pullup */
+				 AT91_PIOA 2 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA2 DAT1 periph B with pullup */
+				 AT91_PIOA 3 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA3 DAT2 periph B with pullup */
+				 AT91_PIOA 4 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>;	/* PA4 DAT3 periph B with pullup */
+		};
+	};
+
+	usb0 {
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins = <AT91_PIOA 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	usb1 {
+		pinctrl_usb_default: usb-default {
+			atmel,pins = <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+}; /* pinctrl */
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_0 &pinctrl_pwm0_1 &pinctrl_pwm0_2>;
+	status = "okay";
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
+	cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	disable-wp;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA 27 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+			   &pioD 18 GPIO_ACTIVE_HIGH
+			   &pioD 15 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
new file mode 100644
index 000000000000..f3cbb675cea4
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
@@ -0,0 +1,672 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x60ek.dts - Device Tree file for Microchip SAM9X60-EK board
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Sandeep Sheriker M <sandeepsheriker.mallikarjun@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x60.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Microchip SAM9X60-EK";
+	compatible = "microchip,sam9x60ek", "microchip,sam9x60", "atmel,at91sam9";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c6;
+		serial1 = &uart5;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-1 {
+			label = "SW1";
+			gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+		status = "okay"; /* Conflict with pwm0. */
+
+		red {
+			label = "red";
+			gpios = <&pioB 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		green {
+			label = "green";
+			gpios = <&pioB 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		blue {
+			label = "blue";
+			gpios = <&pioB 13 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vdd_1v8: fixed-regulator-vdd_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vdd_1v15: fixed-regulator-vdd_1v15 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-always-on;
+	};
+
+	vdd1_3v3: fixed-regulator-vdd1_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD1_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd2_3v3: regulator-fixed-vdd2_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD2_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd1_3v3>;
+	vref-supply = <&vdd1_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_rx_tx>;
+	status = "disabled"; /* Conflict with dbgu. */
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_rx_tx>;
+	status = "okay";
+};
+
+&classd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_classd_default>;
+	atmel,pwm-type = "diff";
+	atmel,non-overlap-time = <10>;
+	status = "okay";
+};
+
+&dbgu {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu>;
+	status = "okay"; /* Conflict with can0. */
+};
+
+&ebi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_0_7>;
+	status = "okay";
+
+	nand_controller: nand-controller {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <8>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				uboot@40000 {
+					label = "u-boot";
+					reg = <0x40000 0xc0000>;
+				};
+
+				ubootenvred@100000 {
+					label = "U-Boot Env Redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				ubootenv@140000 {
+					label = "U-Boot Env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x1f800000>;
+				};
+			};
+		};
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c0: i2c@600 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		eeprom@53 {
+			compatible = "atmel,24c02";
+			reg = <0x53>;
+			pagesize = <16>;
+			status = "okay";
+		};
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "disabled";
+
+	spi4: spi@400 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx4_default>;
+		status = "disabled";
+	};
+};
+
+&flx5 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart5: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx5_default>;
+		status = "okay";
+	};
+};
+
+&flx6 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c6: i2c@600 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx6_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		gpio_exp: mcp23008@20 {
+			compatible = "microchip,mcp23008";
+			reg = <0x20>;
+		};
+	};
+};
+
+&gpbr {
+	status = "okay";
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2s_default>;
+	#sound-dai-cells = <0>;
+	status = "disabled"; /* Conflict with QSPI. */
+};
+
+&macb0 {
+	phy-mode = "rmii";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_macb0_rmii>;
+	status = "okay";
+
+	ethernet-phy@0 {
+		reg = <0x0>;
+		interrupt-parent = <&pioB>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl {
+	adc {
+		pinctrl_adc_default: adc_default {
+			atmel,pins = <AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_adtrg_default: adtrg_default {
+			atmel,pins = <AT91_PIOB 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	dbgu {
+		pinctrl_dbgu: dbgu-0 {
+			atmel,pins = <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				      AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+	};
+
+	i2s {
+		pinctrl_i2s_default: i2s {
+			atmel,pins =
+				<AT91_PIOB 19 AT91_PERIPH_B AT91_PINCTRL_NONE		/* I2SCK */
+				 AT91_PIOB 20 AT91_PERIPH_B AT91_PINCTRL_NONE		/* I2SWS */
+				 AT91_PIOB 21 AT91_PERIPH_B AT91_PINCTRL_NONE		/* I2SDIN */
+				 AT91_PIOB 22 AT91_PERIPH_B AT91_PINCTRL_NONE		/* I2SDOUT */
+				 AT91_PIOB 23 AT91_PERIPH_B AT91_PINCTRL_NONE>;		/* I2SMCK */
+		};
+	};
+
+	qspi {
+		pinctrl_qspi: qspi {
+			atmel,pins =
+				<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_SLEWRATE_DIS
+				 AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_SLEWRATE_DIS
+				 AT91_PIOB 21 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOB 22 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOB 23 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOB 24 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+	};
+
+	nand {
+		pinctrl_nand_oe_we: nand-oe-we-0 {
+			atmel,pins =
+				<AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_nand_rb: nand-rb-0 {
+			atmel,pins =
+				<AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_nand_cs: nand-cs-0 {
+			atmel,pins =
+				<AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	ebi {
+		pinctrl_ebi_data_0_7: ebi-data-lsb-0 {
+			atmel,pins =
+				<AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_ebi_data_0_15: ebi-data-msb-0 {
+			atmel,pins =
+				<AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_ebi_addr_nand: ebi-addr-0 {
+			atmel,pins =
+				<AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+	};
+
+	flexcom {
+		pinctrl_flx0_default: flx0_twi {
+			atmel,pins =
+				<AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_flx4_default: flx4_spi {
+			atmel,pins =
+				<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE
+				 AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_flx5_default: flx5_uart {
+			atmel,pins =
+				<AT91_PIOA 7 AT91_PERIPH_C AT91_PINCTRL_NONE
+				 AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE
+				 AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE
+				 AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_flx6_default: flx6_twi {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	classd {
+		pinctrl_classd_default: classd {
+			atmel,pins =
+				<AT91_PIOA 24 AT91_PERIPH_C AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 25 AT91_PERIPH_C AT91_PINCTRL_PULL_DOWN
+				 AT91_PIOA 26 AT91_PERIPH_C AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 27 AT91_PERIPH_C AT91_PINCTRL_PULL_DOWN>;
+		};
+	};
+
+	can0 {
+		pinctrl_can0_rx_tx: can0_rx_tx {
+			atmel,pins =
+				<AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX0 */
+				 AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANTX0 */
+				 AT91_PIOD 20 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN	/* Enable CAN0 mux */
+				 AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>;	/* Enable CAN Transceivers */
+		};
+	};
+
+	can1 {
+		pinctrl_can1_rx_tx: can1_rx_tx {
+			atmel,pins =
+				<AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX1 RXD1 */
+				 AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANTX1 TXD1 */
+				 AT91_PIOD 19 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN	/* Enable CAN1 mux */
+				 AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>;	/* Enable CAN Transceivers */
+		};
+	};
+
+	macb0 {
+		pinctrl_macb0_rmii: macb0_rmii-0 {
+			atmel,pins =
+				<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB0 periph A */
+				 AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB1 periph A */
+				 AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB2 periph A */
+				 AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB3 periph A */
+				 AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB4 periph A */
+				 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB5 periph A */
+				 AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB6 periph A */
+				 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB7 periph A */
+				 AT91_PIOB 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE	/* PB8 IRQ GPIO */
+				 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB9 periph A */
+				 AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PB10 periph A */
+		};
+	};
+
+	pwm0 {
+		pinctrl_pwm0_0: pwm0_0 {
+			atmel,pins = <AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_1: pwm0_1 {
+			atmel,pins = <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_2: pwm0_2 {
+			atmel,pins = <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_3: pwm0_3 {
+			atmel,pins = <AT91_PIOB 14 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc0 {
+		pinctrl_sdmmc0_default: sdmmc0 {
+			atmel,pins =
+				<AT91_PIOA 17 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI)				/* PA17 CK  periph A with pullup */
+				 AT91_PIOA 16 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA16 CMD periph A with pullup */
+				 AT91_PIOA 15 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA15 DAT0 periph A */
+				 AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA18 DAT1 periph A with pullup */
+				 AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA19 DAT2 periph A with pullup */
+				 AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>;	/* PA20 DAT3 periph A with pullup */
+		};
+		pinctrl_sdmmc0_cd: sdmmc0_cd {
+			atmel,pins =
+				<AT91_PIOA 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc1 {
+		pinctrl_sdmmc1_default: sdmmc1 {
+			atmel,pins =
+				<AT91_PIOA 13 AT91_PERIPH_B (AT91_PINCTRL_DRIVE_STRENGTH_HI)				/* PA13 CK periph B */
+				 AT91_PIOA 12 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA12 CMD periph B with pullup */
+				 AT91_PIOA 11 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA11 DAT0 periph B with pullup */
+				 AT91_PIOA  2 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA2 DAT1 periph B with pullup */
+				 AT91_PIOA  3 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA3 DAT2 periph B with pullup */
+				 AT91_PIOA  4 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>;	/* PA4 DAT3 periph B with pullup */
+		};
+	};
+
+	gpio_keys {
+		pinctrl_key_gpio_default: pinctrl_key_gpio {
+			atmel,pins = <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	usb0 {
+		pinctrl_usba_vbus: usba_vbus {
+			atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	usb1 {
+		pinctrl_usb_default: usb_default {
+			atmel,pins = <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	leds {
+		pinctrl_gpio_leds: gpio_leds {
+			atmel,pins = <AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOB 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+}; /* pinctrl */
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_0 &pinctrl_pwm0_1 &pinctrl_pwm0_2 &pinctrl_pwm0_3>;
+	status = "disabled"; /* Conflict with leds. */
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
+	status = "okay";
+	cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+	disable-wp;
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	no-1-8-v;
+	non-removable;
+	status = "disabled"; /* Conflict with flx4. */
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay"; /* Conflict with i2s. */
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-ns = <7>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+
+		at91bootstrap@0 {
+			label = "qspi: at91bootstrap";
+			reg = <0x0 0x40000>;
+		};
+
+		bootloader@40000 {
+			label = "qspi: bootloader";
+			reg = <0x40000 0xc0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "qspi: bootloader env redundant";
+			reg = <0x100000 0x40000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "qspi: bootloader env";
+			reg = <0x140000 0x40000>;
+		};
+
+		dtb@180000 {
+			label = "qspi: device tree";
+			reg = <0x180000 0x80000>;
+		};
+
+		kernel@200000 {
+			label = "qspi: kernel";
+			reg = <0x200000 0x600000>;
+		};
+	};
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+			   &pioD 15 GPIO_ACTIVE_HIGH
+			   &pioD 16 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi b/arch/arm/boot/dts/microchip/at91-sama5d27_som1.dtsi
index 7788d5db65c2..95ecb7d040a8 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_som1.dtsi
@@ -8,11 +8,16 @@
  */
 #include "sama5d2.dtsi"
 #include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Atmel SAMA5D27 SoM1";
 	compatible = "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
 
+	aliases {
+		i2c0 = &i2c0;
+	};
+
 	clocks {
 		slow_xtal {
 			clock-frequency = <32768>;
@@ -24,28 +29,67 @@
 	};
 
 	ahb {
+		sdmmc0: sdio-host@a0000000 {
+			microchip,sdcal-inverted;
+		};
+
 		apb {
 			qspi1: spi@f0024000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_qspi1_default>;
 
 				flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
 					compatible = "jedec,spi-nor";
 					reg = <0>;
-					spi-max-frequency = <80000000>;
+					spi-max-frequency = <104000000>;
+					spi-cs-setup-ns = <7>;
 					spi-tx-bus-width = <4>;
 					spi-rx-bus-width = <4>;
 					m25p,fast-read;
+
+					at91bootstrap@0 {
+						label = "at91bootstrap";
+						reg = <0x00000000 0x00040000>;
+					};
+
+					bootloader@40000 {
+						label = "bootloader";
+						reg = <0x00040000 0x000c0000>;
+					};
+
+					bootloaderenvred@100000 {
+						label = "bootloader env redundant";
+						reg = <0x00100000 0x00040000>;
+					};
+
+					bootloaderenv@140000 {
+						label = "bootloader env";
+						reg = <0x00140000 0x00040000>;
+					};
+
+					dtb@180000 {
+						label = "device tree";
+						reg = <0x00180000 0x00080000>;
+					};
+
+					kernel@200000 {
+						label = "kernel";
+						reg = <0x00200000 0x00600000>;
+					};
 				};
 			};
 
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 
-				ethernet-phy@0 {
-					reg = <0x0>;
+				ethernet-phy@7 {
+					reg = <0x7>;
 					interrupt-parent = <&pioA>;
 					interrupts = <PIN_PD31 IRQ_TYPE_LEVEL_LOW>;
 					pinctrl-names = "default";
@@ -53,7 +97,34 @@
 				};
 			};
 
+			i2c0: i2c@f8028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&pinctrl_i2c0_default>;
+				pinctrl-1 = <&pinctrl_i2c0_gpio>;
+				sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				status = "okay";
+
+				at24@50 {
+					compatible = "atmel,24c02";
+					reg = <0x50>;
+					pagesize = <8>;
+				};
+			};
+
 			pinctrl@fc038000 {
+				pinctrl_i2c0_default: i2c0_default {
+					pinmux = <PIN_PD21__TWD0>,
+						 <PIN_PD22__TWCK0>;
+					bias-disable;
+				};
+
+				pinctrl_i2c0_gpio: i2c0_gpio {
+					pinmux = <PIN_PD21__GPIO>,
+						 <PIN_PD22__GPIO>;
+					bias-disable;
+				};
 
 				pinctrl_qspi1_default: qspi1_default {
 					sck_cs {
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
index fca5716ce44f..f3ffb8f01d8a 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
@@ -11,6 +11,7 @@
 #include "at91-sama5d27_som1.dtsi"
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Atmel SAMA5D27 SOM1 EK";
@@ -20,8 +21,8 @@
 		serial0 = &uart1;	/* DBGU */
 		serial1 = &uart4;	/* mikro BUS 1 */
 		serial2 = &uart2;	/* mikro BUS 2 */
-		i2c1	= &i2c1;
-		i2c2	= &i2c2;
+		i2c1 = &i2c1;
+		i2c2 = &i2c3;
 	};
 
 	chosen {
@@ -53,7 +54,6 @@
 
 		sdmmc0: sdio-host@a0000000 {
 			bus-width = <8>;
-			mmc-ddr-3_3v;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sdmmc0_default>;
 			status = "okay";
@@ -70,7 +70,6 @@
 			isc: isc@f0008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
-				status = "okay";
 			};
 
 			qspi1: spi@f0024000 {
@@ -125,29 +124,26 @@
 				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
 				status = "okay";
 
-				i2c2: i2c@600 {
-					compatible = "atmel,sama5d2-i2c";
-					reg = <0x600 0x200>;
-					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+				i2c3: i2c@600 {
 					dmas = <0>, <0>;
-					dma-names = "tx", "rx";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
-					pinctrl-names = "default";
+					i2c-analog-filter;
+					i2c-digital-filter;
+					i2c-digital-filter-width-ns = <35>;
+					pinctrl-names = "default", "gpio";
 					pinctrl-0 = <&pinctrl_mikrobus_i2c>;
-					atmel,fifo-size = <16>;
+					pinctrl-1 = <&pinctrl_i2c3_gpio>;
+					sda-gpios = <&pioA PIN_PA24 GPIO_ACTIVE_HIGH>;
+					scl-gpios = <&pioA PIN_PA23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 					status = "okay";
 				};
 			};
 
-			shdwc@f8048010 {
-				atmel,shdwc-debouncer = <976>;
+			poweroff@f8048010 {
+				debounce-delay-us = <976>;
 				atmel,wakeup-rtc-timer;
 
 				input@0 {
 					reg = <0>;
-					atmel,wakeup-type = "low";
 				};
 			};
 
@@ -175,27 +171,17 @@
 				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
 				status = "disabled";
 
-				uart7: serial@200 {
-					compatible = "atmel,at91sam9260-usart";
-					reg = <0x200 0x200>;
-					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-					clock-names = "usart";
+				uart8: serial@200 {
+					dmas = <0>, <0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx3_default>;
-					atmel,fifo-size = <32>;
 					status = "disabled"; /* Conflict with isc. */
 				};
 
-				spi2: spi@400 {
-					compatible = "atmel,at91rm9200-spi";
-					reg = <0x400 0x200>;
-					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-					clock-names = "spi_clk";
+				spi5: spi@400 {
+					dmas = <0>, <0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx3_default>;
-					atmel,fifo-size = <16>;
 					status = "disabled"; /* Conflict with isc. */
 				};
 			};
@@ -204,58 +190,48 @@
 				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
 				status = "okay";
 
-				uart6: serial@200 {
-					compatible = "atmel,at91sam9260-usart";
-					reg = <0x200 0x200>;
-					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
-					clock-names = "usart";
+				uart9: serial@200 {
+					dmas = <0>, <0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx4_default>;
-					atmel,fifo-size = <32>;
-					status = "disabled"; /* Conflict with spi3 and i2c3. */
+					status = "disabled"; /* Conflict with spi6 and i2c6. */
 				};
 
-				spi3: spi@400 {
-					compatible = "atmel,at91rm9200-spi";
-					reg = <0x400 0x200>;
-					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
-					clock-names = "spi_clk";
+				spi6: spi@400 {
+					dmas = <0>, <0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
-					atmel,fifo-size = <16>;
-					status = "okay"; /* Conflict with uart6 and i2c3. */
+					status = "okay"; /* Conflict with uart5 and i2c6. */
 				};
 
-				i2c3: i2c@600 {
-					compatible = "atmel,sama5d2-i2c";
-					reg = <0x600 0x200>;
-					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+				i2c6: i2c@600 {
 					dmas = <0>, <0>;
-					dma-names = "tx", "rx";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx4_default>;
-					atmel,fifo-size = <16>;
-					status = "disabled"; /* Conflict with uart6 and spi3. */
+					status = "disabled"; /* Conflict with uart5 and spi6. */
 				};
 			};
 
 			i2c1: i2c@fc028000 {
 				dmas = <0>, <0>;
-				pinctrl-names = "default";
+				i2c-analog-filter;
+				i2c-digital-filter;
+				i2c-digital-filter-width-ns = <35>;
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c1_default>;
+				pinctrl-1 = <&pinctrl_i2c1_gpio>;
+				sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 			};
 
 			adc: adc@fc030000 {
 				vddana-supply = <&vddana>;
 				vref-supply = <&advref>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mikrobus1_an &pinctrl_mikrobus2_an>;
 
-				status = "disabled";
+				status = "okay";
 			};
 
 			pinctrl@fc038000 {
@@ -281,6 +257,13 @@
 					bias-disable;
 				};
 
+				pinctrl_i2c1_gpio: i2c1_gpio {
+                                        pinmux = <PIN_PD4__GPIO>,
+                                                 <PIN_PD5__GPIO>;
+                                        bias-disable;
+                                };
+
+
 				pinctrl_isc_base: isc_base {
 					pinmux = <PIN_PC21__ISC_PCK>,
 						 <PIN_PC22__ISC_VSYNC>,
@@ -470,6 +453,12 @@
 					bias-disable;
 				};
 
+				pinctrl_i2c3_gpio: i2c3_gpio {
+					pinmux = <PIN_PA24__GPIO>,
+						 <PIN_PA23__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_flx4_default: flx4_uart_default {
 					pinmux = <PIN_PC28__FLEXCOM4_IO0>,
 						 <PIN_PC29__FLEXCOM4_IO1>,
@@ -488,16 +477,16 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		pb4 {
+		button {
 			label = "USER";
 			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
-			linux,code = <0x104>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
@@ -508,17 +497,17 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay"; /* Conflict with pwm0. */
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PA10 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1.dtsi
new file mode 100644
index 000000000000..4617805c7748
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1.dtsi
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d27_wlsom1.dtsi - Device Tree file for SAMA5D27 WLSOM1
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Nicolas Ferre <nicolas.ferre@microcihp.com>
+ * Author: Eugen Hristev <eugen.hristev@microcihp.com>
+ */
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+	model = "Microchip SAMA5D27 WLSOM1";
+	compatible = "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+	aliases {
+		i2c0 = &i2c0;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-wilc1000";
+		reset-gpios = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
+		powerdown-gpios = <&pioA PIN_PA29 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_wilc_pwrseq>;
+		pinctrl-names = "default";
+	};
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+
+	uart6: serial@200 {
+		pinctrl-0 = <&pinctrl_flx1_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	pinctrl-names = "default", "gpio";
+	sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c1 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	mcp16502@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+		status = "okay";
+		lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddio_ddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1200000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1200000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vdd_core: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vdd_ddr: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&macb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_macb0_default>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	phy-mode = "rmii";
+
+	ethernet-phy@0 {
+		reg = <0x0>;
+		interrupt-parent = <&pioA>;
+		interrupts = <PIN_PB24 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_macb0_phy_irq>;
+	};
+};
+
+&pmc {
+	atmel,osc-bypass;
+};
+
+&qspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi1_default>;
+	status = "disabled";
+
+	qspi1_flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-ns = <7>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		m25p,fast-read;
+		status = "disabled";
+
+		at91bootstrap@0 {
+			label = "at91bootstrap";
+			reg = <0x0 0x40000>;
+		};
+
+		bootloader@40000 {
+			label = "bootloader";
+			reg = <0x40000 0xc0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "bootloader env redundant";
+			reg = <0x100000 0x40000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "bootloader env";
+			reg = <0x140000 0x40000>;
+		};
+
+		dtb@180000 {
+			label = "device tree";
+			reg = <0x180000 0x80000>;
+		};
+
+		kernel@200000 {
+			label = "kernel";
+			reg = <0x200000 0x600000>;
+		};
+	};
+};
+
+&pioA {
+	pinctrl_flx1_default: flx1_usart_default {
+		pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+			 <PIN_PA23__FLEXCOM1_IO1>,
+			 <PIN_PA25__FLEXCOM1_IO3>,
+			 <PIN_PA26__FLEXCOM1_IO4>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_default: i2c0_default {
+		pinmux = <PIN_PD21__TWD0>,
+			 <PIN_PD22__TWCK0>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_gpio: i2c0_gpio {
+		pinmux = <PIN_PD21__GPIO>,
+			 <PIN_PD22__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_default: i2c1_default {
+		pinmux = <PIN_PD19__TWD1>,
+			 <PIN_PD20__TWCK1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_gpio: i2c1_gpio {
+		pinmux = <PIN_PD19__GPIO>,
+			 <PIN_PD20__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_macb0_default: macb0_default {
+		pinmux = <PIN_PB14__GTXCK>,
+			 <PIN_PB15__GTXEN>,
+			 <PIN_PB16__GRXDV>,
+			 <PIN_PB17__GRXER>,
+			 <PIN_PB18__GRX0>,
+			 <PIN_PB19__GRX1>,
+			 <PIN_PB20__GTX0>,
+			 <PIN_PB21__GTX1>,
+			 <PIN_PB22__GMDC>,
+			 <PIN_PB23__GMDIO>;
+		bias-disable;
+	};
+
+	pinctrl_macb0_phy_irq: macb0_phy_irq {
+		pinmux = <PIN_PB24__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_qspi1_default: qspi1_default {
+		pinmux = <PIN_PB5__QSPI1_SCK>,
+			 <PIN_PB6__QSPI1_CS>,
+			 <PIN_PB7__QSPI1_IO0>,
+			 <PIN_PB8__QSPI1_IO1>,
+			 <PIN_PB9__QSPI1_IO2>,
+			 <PIN_PB10__QSPI1_IO3>;
+		bias-pull-up;
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1_default {
+		cmd-data {
+			pinmux = <PIN_PA28__SDMMC1_CMD>,
+				 <PIN_PA18__SDMMC1_DAT0>,
+				 <PIN_PA19__SDMMC1_DAT1>,
+				 <PIN_PA20__SDMMC1_DAT2>,
+				 <PIN_PA21__SDMMC1_DAT3>;
+			bias-disable;
+		};
+
+		conf-ck {
+			pinmux = <PIN_PA22__SDMMC1_CK>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_wilc_default: wilc_default {
+		conf-irq {
+			pinmux = <PIN_PB25__GPIO>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_wilc_pwrseq: wilc_pwrseq {
+		conf-ce-nrst {
+			pinmux = <PIN_PA27__GPIO>,
+				 <PIN_PA29__GPIO>;
+			bias-disable;
+		};
+
+		conf-rtcclk {
+			pinmux = <PIN_PB13__PCK1>;
+			bias-disable;
+		};
+	};
+};
+
+&sdmmc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	no-1-8-v;
+	non-removable;
+	bus-width = <4>;
+	status = "okay";
+
+	wilc: wifi@0 {
+		reg = <0>;
+		compatible = "microchip,wilc1000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wilc_default>;
+		clocks = <&pmc PMC_TYPE_SYSTEM 9>;
+		clock-names = "rtc";
+		interrupts = <PIN_PB25 IRQ_TYPE_NONE>;
+		interrupt-parent = <&pioA>;
+		assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
+		assigned-clock-rates = <32768>;
+	};
+};
+
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
new file mode 100644
index 000000000000..15239834d886
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d27_wlsom1_ek.dts - Device Tree file for SAMA5D27 WLSOM1 EK
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Nicolas Ferre <nicolas.ferre@microcihp.com>
+ */
+/dts-v1/;
+#include "at91-sama5d27_wlsom1.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Microchip SAMA5D27 WLSOM1 EK";
+	compatible = "microchip,sama5d27-wlsom1-ek", "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+	aliases {
+		serial0 = &uart0;	/* DBGU */
+		serial1 = &uart6;	/* BT */
+		serial2 = &uart5;	/* mikro BUS 2 */
+		serial3 = &uart3;	/* mikro BUS 1 */
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-1 {
+			label = "USER BUTTON";
+			gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay";
+
+		led-red {
+			label = "red";
+			gpios = <&pioA PIN_PA6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd_3v3>;
+	vref-supply = <&vdd_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default>;
+	status = "okay";
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart5: serial@200 {
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		pinctrl-names = "default";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		status = "okay";
+	};
+};
+
+&flx1 {
+	status = "okay";
+
+	uart6: serial@200 {
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		status = "okay";
+	};
+};
+
+&macb0 {
+	status = "okay";
+};
+
+&pioA {
+	/*
+	 * There is no real pinmux for ADC, if the pin
+	 * is not requested by another peripheral then
+	 * the muxing is done when channel is enabled.
+	 * Requesting pins for ADC is GPIO is
+	 * encouraged to prevent conflicts and to
+	 * disable bias in order to be in the same
+	 * state when the pin is not muxed to the adc.
+	 */
+	pinctrl_adc_default: adc_default {
+		pinmux = <PIN_PD25__GPIO>,
+			 <PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_flx0_default: flx0_usart_default {
+		pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+			 <PIN_PB29__FLEXCOM0_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_key_gpio_default: key_gpio_default {
+		pinmux = <PIN_PB2__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led_gpio_default {
+		pinmux = <PIN_PA6__GPIO>,
+			 <PIN_PA7__GPIO>,
+			 <PIN_PA8__GPIO>;
+		bias-pull-down;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0_default {
+		cmd_data {
+			pinmux = <PIN_PA1__SDMMC0_CMD>,
+				 <PIN_PA2__SDMMC0_DAT0>,
+				 <PIN_PA3__SDMMC0_DAT1>,
+				 <PIN_PA4__SDMMC0_DAT2>,
+				 <PIN_PA5__SDMMC0_DAT3>;
+			bias-disable;
+		};
+
+		ck_cd_vddsel {
+			pinmux = <PIN_PA0__SDMMC0_CK>,
+				 <PIN_PA11__SDMMC0_VDDSEL>,
+				 <PIN_PA12__SDMMC0_WP>,
+				 <PIN_PA13__SDMMC0_CD>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart0_default: uart0_default {
+		pinmux = <PIN_PB26__URXD0>,
+			 <PIN_PB27__UTXD0>;
+		bias-disable;
+	};
+
+	pinctrl_uart3_default: uart3_default {
+		pinmux = <PIN_PB11__URXD3>,
+			 <PIN_PB12__UTXD3>;
+		bias-disable;
+	};
+
+	pinctrl_pwm0_default: pwm0_default {
+		pinmux = <PIN_PA31__PWML0>,
+			 <PIN_PA30__PWMH0>;
+		bias-disable;
+	};
+
+	pinctrl_usb_default: usb_default {
+		pinmux = <PIN_PA10__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_usba_vbus: usba_vbus {
+		pinmux = <PIN_PA16__GPIO>;
+		bias-disable;
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default>;
+	status = "okay";
+};
+
+&qspi1 {
+	status = "okay";
+
+	qspi1_flash: flash@0 {
+		status = "okay";
+	};
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	atmel,wakeup-rtc-timer;
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_default>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA PIN_PA16 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+			   &pioA PIN_PA10 GPIO_ACTIVE_HIGH
+			   0
+			  >;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	phy_type = "hsic";
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
new file mode 100644
index 000000000000..6b02b7bcfd49
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
@@ -0,0 +1,600 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d29_curiosity.dts - Device Tree file for SAMA5D29 Curiosity board
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Mihai Sain <mihai.sain@microchip.com>
+ *
+ */
+/dts-v1/;
+#include "sama5d29.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/ {
+	model = "Microchip SAMA5D29 Curiosity";
+	compatible = "microchip,sama5d29-curiosity", "atmel,sama5d29", "atmel,sama5d2", "atmel,sama5";
+
+	aliases {
+		serial0 = &uart0;	// debug
+		serial1 = &uart1;	// RPi
+		serial2 = &uart3;	// mikro BUS 2
+		serial3 = &uart4;	// mikro BUS 1
+		serial4 = &uart6;	// flx1 Bluetooth
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-1 {
+			label = "USER BUTTON";
+			gpios = <&pioA PIN_PA17 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay";
+
+		led-red {
+			label = "red";
+			gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioA PIN_PA9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x20000000>;
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd_3v3>;
+	vref-supply = <&vdd_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart6: serial@200 {
+		pinctrl-0 = <&pinctrl_flx1_default>;
+		pinctrl-names = "default";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi6: spi@400 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rpi_spi>;
+		status = "okay";
+	};
+};
+
+&i2c0 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	sda-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PC0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	i2c-sda-hold-time-ns = <350>;
+	status = "okay";
+
+	mcp16502@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+		status = "okay";
+		lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddio_ddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1200000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1200000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vdd_core: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vdd_ddr: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pioA {
+	pinctrl_adc_default: adc-default {
+		pinmux = <PIN_PD25__GPIO>,
+			 <PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_adtrg_default: adtrg-default {
+		pinmux = <PIN_PD31__ADTRG>;
+		bias-pull-up;
+	};
+
+	pinctrl_can0_default: can0-default {
+		pinmux = <PIN_PC10__CANTX0>,
+			 <PIN_PC11__CANRX0>;
+		bias-disable;
+	};
+
+	pinctrl_can1_default: can1-default {
+		pinmux = <PIN_PC26__CANTX1>,
+			 <PIN_PC27__CANRX1>;
+		bias-disable;
+	};
+
+	pinctrl_debug_uart: debug-uart {
+		pinmux = <PIN_PB26__URXD0>,
+			 <PIN_PB27__UTXD0>;
+		bias-disable;
+	};
+
+	pinctrl_flx1_default: flx1-default {
+		pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+			 <PIN_PA23__FLEXCOM1_IO1>,
+			 <PIN_PA25__FLEXCOM1_IO3>,
+			 <PIN_PA26__FLEXCOM1_IO4>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_default: i2c0-default {
+		pinmux = <PIN_PB31__TWD0>,
+			 <PIN_PC0__TWCK0>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio-default {
+		pinmux = <PIN_PB31__GPIO>,
+			 <PIN_PC0__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		pinmux = <PIN_PD4__TWD1>,
+			 <PIN_PD5__TWCK1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-default {
+		pinmux = <PIN_PD4__GPIO>,
+			 <PIN_PD5__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_key_gpio_default: key-gpio-default {
+		pinmux = <PIN_PA17__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led-gpio-default {
+		pinmux = <PIN_PA7__GPIO>,
+			 <PIN_PA8__GPIO>,
+			 <PIN_PA9__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_mikrobus1_pwm: mikrobus1-pwm {
+		pinmux = <PIN_PA31__PWML0>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_pwm: mikrobus2-pwm {
+		pinmux = <PIN_PB0__PWMH1>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_uart: mikrobus1-uart {
+		pinmux = <PIN_PB3__URXD4>,
+			 <PIN_PB4__UTXD4>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_uart: mikrobus2-uart {
+		pinmux = <PIN_PB11__URXD3>,
+			 <PIN_PB12__UTXD3>;
+		bias-disable;
+	};
+
+	pinctrl_qspi1_default: qspi1-default {
+		pinmux = <PIN_PB5__QSPI1_SCK>,
+			 <PIN_PB6__QSPI1_CS>,
+			 <PIN_PB7__QSPI1_IO0>,
+			 <PIN_PB8__QSPI1_IO1>,
+			 <PIN_PB9__QSPI1_IO2>,
+			 <PIN_PB10__QSPI1_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_rpi_spi: rpi-spi {
+		pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+			 <PIN_PD13__FLEXCOM4_IO1>,
+			 <PIN_PD14__FLEXCOM4_IO2>,
+			 <PIN_PD15__FLEXCOM4_IO3>,
+			 <PIN_PD16__FLEXCOM4_IO4>;
+		bias-disable;
+	};
+
+	pinctrl_rpi_uart: rpi-uart {
+		pinmux = <PIN_PD2__URXD1>,
+			 <PIN_PD3__UTXD1>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0-default {
+		pinmux = <PIN_PA0__SDMMC0_CK>,
+			 <PIN_PA1__SDMMC0_CMD>,
+			 <PIN_PA2__SDMMC0_DAT0>,
+			 <PIN_PA3__SDMMC0_DAT1>,
+			 <PIN_PA4__SDMMC0_DAT2>,
+			 <PIN_PA5__SDMMC0_DAT3>,
+			 <PIN_PA11__SDMMC0_VDDSEL>,
+			 <PIN_PA13__SDMMC0_CD>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1-default {
+		pinmux = <PIN_PA18__SDMMC1_DAT0>,
+			 <PIN_PA19__SDMMC1_DAT1>,
+			 <PIN_PA20__SDMMC1_DAT2>,
+			 <PIN_PA21__SDMMC1_DAT3>,
+			 <PIN_PA22__SDMMC1_CK>,
+			 <PIN_PA28__SDMMC1_CMD>,
+			 <PIN_PA30__SDMMC1_CD>;
+		bias-disable;
+	};
+
+	pinctrl_spi1_default: spi1-default {
+		pinmux = <PIN_PC1__SPI1_SPCK>,
+			 <PIN_PC2__SPI1_MOSI>,
+			 <PIN_PC3__SPI1_MISO>,
+			 <PIN_PC4__SPI1_NPCS0>,
+			 <PIN_PC5__SPI1_NPCS1>,
+			 <PIN_PC6__SPI1_NPCS2>,
+			 <PIN_PC7__SPI1_NPCS3>;
+		bias-disable;
+	};
+
+	pinctrl_usb_default: usb-default {
+		pinmux = <PIN_PA6__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_usba_vbus: usba-vbus {
+		pinmux = <PIN_PB13__GPIO>;
+		bias-disable;
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_pwm &pinctrl_mikrobus2_pwm>;
+	status = "okay";
+};
+
+&qspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi1_default>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+		label = "atmel_qspi1";
+		status = "okay";
+
+		at91bootstrap@0 {
+			label = "at91bootstrap";
+			reg = <0x0 0x40000>;
+		};
+
+		bootloader@40000 {
+			label = "bootloader";
+			reg = <0x40000 0xc0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "bootloader env redundant";
+			reg = <0x100000 0x40000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "bootloader env";
+			reg = <0x140000 0x40000>;
+		};
+
+		dtb@180000 {
+			label = "device tree";
+			reg = <0x180000 0x80000>;
+		};
+
+		kernel@200000 {
+			label = "kernel";
+			reg = <0x200000 0x600000>;
+		};
+	};
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	disable-wp;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	disable-wp;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	atmel,wakeup-rtc-timer;
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_debug_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rpi_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus2_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA PIN_PB13 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+			   &pioA PIN_PA6 GPIO_ACTIVE_HIGH
+			   0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
new file mode 100644
index 000000000000..999adeca6f33
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
@@ -0,0 +1,790 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d2_icp.dts - Device Tree file for SAMA5D2-ICP board
+ *
+ *  Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ *	Author: Radu Pirea & Razvan Stefanescu,
+ *		Codrin Ciubotariu <codrin.ciubotariu@microchip.com>,
+ *		Cristian Birsan <cristian.birsan@microchip.com>
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/ {
+	model = "Microchip SAMA5D2-ICP";
+	compatible = "microchip,sama5d2-icp", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+	aliases {
+		serial0 = &uart0;	/* debug uart0 + mikro BUS 1 */
+		serial1 = &uart1;	/* mikro BUS 3 */
+		serial3 = &uart3;	/* mikro BUS 2 */
+		serial5 = &uart7;	/* flx2 */
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-1 {
+			label = "USER_PB1";
+			gpios = <&pioA PIN_PD0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay"; /* conflict with pwm0 */
+
+		led-red {
+			label = "red";
+			gpios = <&pioA PIN_PB0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd_io_reg>;
+	vref-supply = <&vdd_io_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
+&flx0 { /* mikrobus2 spi */
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi2: spi@400 {
+		dmas = <0>, <0>;
+		cs-gpios = <&pioA PIN_PC0 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mikrobus2_spi &pinctrl_ksz_spi_cs>;
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0: ksz8563@0 {
+			compatible = "microchip,ksz8563";
+			reg = <0>;
+			reset-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_LOW>;
+
+			spi-max-frequency = <500000>;
+			spi-cpha;
+			spi-cpol;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "lan1";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan2";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "cpu";
+					ethernet = <&macb0>;
+					phy-mode = "mii";
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
+};
+
+&flx2 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart7: serial@200 {
+		pinctrl-0 = <&pinctrl_flx2_default>;
+		pinctrl-names = "default";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		status = "okay"; /* Conflict w/ qspi1. */
+	};
+};
+
+&flx3 { /* mikrobus1 spi */
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi5: spi@400 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mikrobus1_spi &pinctrl_mikrobus1_spi_cs>;
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c6: i2c@600 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx4_default>;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		mcp16502@5b {
+			compatible = "microchip,mcp16502";
+			reg = <0x5b>;
+			status = "okay";
+			lpm-gpios = <&pioBU 7 GPIO_ACTIVE_LOW>;
+
+			regulators {
+				vdd_io_reg: VDD_IO {
+					regulator-name = "VDD_IO";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				VDD_DDR {
+					regulator-name = "VDD_DDR";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				VDD_CORE {
+					regulator-name = "VDD_CORE";
+					regulator-min-microvolt = <1250000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				VDD_OTHER {
+					regulator-name = "VDD_OTHER";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1850000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				LDO1 {
+					regulator-name = "LDO1";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				LDO2 {
+					regulator-name = "LDO2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+			};
+		};
+	};
+};
+
+&i2c0 { /* mikrobus i2c */
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_mikrobus_i2c>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	status = "okay";
+};
+
+&i2c1 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+		status = "okay";
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+		status = "disabled";
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+		status = "disabled";
+	};
+};
+
+&macb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq &pinctrl_macb0_rst>;
+	phy-mode = "mii";
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&pioA {
+	pinctrl_adc_default: adc_default {
+		pinmux = <PIN_PD24__GPIO>,
+				<PIN_PD25__GPIO>,
+				<PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	/*
+	 * The ADTRG pin can work on any edge type.
+	 * In here it's being pulled up, so need to
+	 * connect it to ground to get an edge e.g.
+	 * Trigger can be configured on falling, rise
+	 * or any edge, and the pull-up can be changed
+	 * to pull-down or left floating according to
+	 * needs.
+	 */
+	pinctrl_adtrg_default: adtrg_default {
+		pinmux = <PIN_PD31__ADTRG>;
+		bias-pull-up;
+	};
+
+	pinctrl_flx4_default: flx4_default {
+		pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+			 <PIN_PC29__FLEXCOM4_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_can0_default: can0_default {
+		pinmux = <PIN_PC10__CANTX0>,
+			 <PIN_PC11__CANRX0>;
+		bias-disable;
+	};
+
+	pinctrl_can1_default: can1_default {
+		pinmux = <PIN_PC26__CANTX1>,
+			 <PIN_PC27__CANRX1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_default: i2c1_default {
+		pinmux = <PIN_PD19__TWD1>,
+			 <PIN_PD20__TWCK1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_gpio: i2c1_gpio {
+                pinmux = <PIN_PD19__GPIO>,
+                         <PIN_PD20__GPIO>;
+                bias-disable;
+        };
+
+	pinctrl_key_gpio_default: key_gpio_default {
+		pinmux = <PIN_PD0__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led_gpio_default {
+		pinmux = <PIN_PB0__GPIO>,
+			 <PIN_PB1__GPIO>,
+			 <PIN_PA31__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_qspi1_default: qspi1_default {
+		pinmux = <PIN_PA6__QSPI1_SCK>,
+			 <PIN_PA7__QSPI1_IO0>,
+			 <PIN_PA8__QSPI1_IO1>,
+			 <PIN_PA9__QSPI1_IO2>,
+			 <PIN_PA10__QSPI1_IO3>,
+			 <PIN_PA11__QSPI1_CS>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0_default {
+		cmd_data {
+			pinmux = <PIN_PA1__SDMMC0_CMD>,
+				 <PIN_PA2__SDMMC0_DAT0>,
+				 <PIN_PA3__SDMMC0_DAT1>,
+				 <PIN_PA4__SDMMC0_DAT2>,
+				 <PIN_PA5__SDMMC0_DAT3>;
+			bias-disable;
+		};
+
+		ck_cd {
+			pinmux = <PIN_PA0__SDMMC0_CK>,
+				 <PIN_PA13__SDMMC0_CD>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1_default {
+		cmd_data {
+			pinmux = <PIN_PA18__SDMMC1_DAT0>,
+				 <PIN_PA19__SDMMC1_DAT1>,
+				 <PIN_PA20__SDMMC1_DAT2>,
+				 <PIN_PA21__SDMMC1_DAT3>;
+			bias-disable;
+		};
+
+		ck_cd {
+			pinmux = <PIN_PA22__SDMMC1_CK>,
+				 <PIN_PA28__SDMMC1_CMD>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_mikrobus_i2c: mikrobus_i2c {
+		pinmux = <PIN_PD22__TWCK0>,
+			 <PIN_PD21__TWD0>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_gpio: i2c0_gpio {
+		pinmux = <PIN_PD21__GPIO>,
+			 <PIN_PD22__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_an: mikrobus1_an {
+		pinmux = <PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_rst: mikrobus1_rst {
+		pinmux = <PIN_PC5__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_spi_cs: mikrobus1_spi_cs {
+		pinmux = <PIN_PC21__FLEXCOM3_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_spi: mikrobus1_spi {
+		pinmux = <PIN_PC20__FLEXCOM3_IO0>,
+			 <PIN_PC19__FLEXCOM3_IO1>,
+			 <PIN_PC18__FLEXCOM3_IO2>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_pwm: mikrobus1_pwm {
+		pinmux = <PIN_PC4__TIOB1>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_int: mikrobus1_int {
+		pinmux = <PIN_PC3__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_uart: mikrobus1_uart {
+		pinmux = <PIN_PB26__URXD0>,
+			 <PIN_PB27__UTXD0>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_an: mikrobus2_an {
+		pinmux = <PIN_PD25__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_rst: mikrobus2_rst {
+		pinmux = <PIN_PB24__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_spi_cs: mikrobus2_spi_cs {
+		pinmux = <PIN_PB31__FLEXCOM0_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_spi: mikrobus2_spi {
+		pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+			 <PIN_PB29__FLEXCOM0_IO1>,
+			 <PIN_PB30__FLEXCOM0_IO2>;
+		bias-disable;
+	};
+
+	pinctrl_ksz_spi_cs: ksz_spi_cs {
+		pinmux = <PIN_PC0__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_pwm: mikrobus2_pwm {
+		pinmux = <PIN_PB23__TIOB2>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_int: mikrobus2_int {
+		pinmux = <PIN_PB22__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_uart: mikrobus2_uart {
+		pinmux = <PIN_PC12__URXD3>,
+			 <PIN_PC13__UTXD3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_an: mikrobus3_an {
+		pinmux = <PIN_PD24__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_rst: mikrobus3_rst {
+		pinmux = <PIN_PB21__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_spi_cs: mikrobus3_spi_cs {
+		pinmux = <PIN_PA17__SPI0_NPCS0>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_spi: mikrobus3_spi {
+		pinmux = <PIN_PA14__SPI0_SPCK>,
+			 <PIN_PA16__SPI0_MISO>,
+			 <PIN_PA15__SPI0_MOSI>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_pwm: mikrobus3_pwm {
+		pinmux = <PIN_PB20__TIOB3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_int: mikrobus3_int {
+		pinmux = <PIN_PB18__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus3_uart: mikrobus3_uart {
+		pinmux = <PIN_PC7__URXD1>,
+			 <PIN_PC8__UTXD1>;
+		bias-disable;
+	};
+
+	pinctrl_usb_default: usb_default {
+		pinmux = <PIN_PC17__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_usba_vbus: usba_vbus {
+		pinmux = <PIN_PD23__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+		pinmux = <PIN_PB5__PWMH2>,
+			 <PIN_PB6__PWML2>;
+		bias-pull-up;
+	};
+
+	pinctrl_macb0_default: macb0_default {
+		pinmux = <PIN_PD1__GRXCK>,
+			 <PIN_PD2__GTXER>,
+			 <PIN_PD5__GRX2>,
+			 <PIN_PD6__GRX3>,
+			 <PIN_PD7__GTX2>,
+			 <PIN_PD8__GTX3>,
+			 <PIN_PD9__GTXCK>,
+			 <PIN_PD10__GTXEN>,
+			 <PIN_PD11__GRXDV>,
+			 <PIN_PD12__GRXER>,
+			 <PIN_PD13__GRX0>,
+			 <PIN_PD14__GRX1>,
+			 <PIN_PD15__GTX0>,
+			 <PIN_PD16__GTX1>,
+			 <PIN_PD17__GMDC>,
+			 <PIN_PD18__GMDIO>;
+		bias-disable;
+	};
+
+	pinctrl_macb0_phy_irq: macb0_phy_irq {
+		pinmux = <PIN_PD3__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_macb0_rst: macb0_sw_rst {
+		pinmux = <PIN_PD4__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_flx2_default: flx2_default {
+		pinmux = <PIN_PA6__FLEXCOM2_IO0>,
+			 <PIN_PA7__FLEXCOM2_IO1>,
+			 <PIN_PA9__FLEXCOM2_IO3>,
+			 <PIN_PA10__FLEXCOM2_IO4>;
+		bias-disable;
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_pwm2_default>;
+	status = "disabled"; /* conflict with leds, HSIC */
+};
+
+&qspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi1_default>;
+	status = "disabled"; /* Conflict with wilc_pwrseq, flx2 */
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-ns = <7>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+
+		at91bootstrap@0 {
+			label = "qspi: at91bootstrap";
+			reg = <0x00000000 0x00040000>;
+		};
+
+		bootloader@40000 {
+			label = "qspi: bootloader";
+			reg = <0x00040000 0x000c0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "qspi: bootloader env redundant";
+			reg = <0x00100000 0x00040000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "qspi: bootloader env";
+			reg = <0x00140000 0x00040000>;
+		};
+
+		dtb@180000 {
+			label = "qspi: device tree";
+			reg = <0x00180000 0x00080000>;
+		};
+
+		kernel@200000 {
+			label = "qspi: kernel";
+			reg = <0x00200000 0x00600000>;
+		};
+	};
+};
+
+&sdmmc0 {
+	no-1-8-v;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	atmel,wakeup-rtc-timer;
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&spi0 {  /* mikrobus3 spi */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus3_spi &pinctrl_mikrobus3_spi_cs>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus3_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus2_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA PIN_PD23 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	phy_type = "hsic";
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_ptc_ek.dts
index ba7f3e646c26..200b20515ab1 100644
--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_ptc_ek.dts
@@ -11,6 +11,7 @@
 #include "sama5d2-pinfunc.h"
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/at91.h>
 
 / {
@@ -18,10 +19,10 @@
 	compatible = "atmel,sama5d2-ptc_ek", "atmel,sama5d2", "atmel,sama5";
 
 	aliases {
-		serial0 = &uart0;
-		i2c0	= &i2c0;
-		i2c1	= &i2c1;
-		i2c2	= &i2c2;
+		serial0 = &uart0;	/* DBGU */
+		i2c0 = &i2c0;	/* mikroBUS 1 */
+		i2c1 = &i2c1;	/* XPRO EXT1 */
+		i2c2 = &i2c2;
 	};
 
 	chosen {
@@ -40,7 +41,7 @@
 
 	ahb {
 		usb0: gadget@300000 {
-			atmel,vbus-gpio = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
+			atmel,vbus-gpio = <&pioA PIN_PB11 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usba_vbus>;
 			status = "okay";
@@ -92,12 +93,12 @@
 							reg = <0x40000 0xc0000>;
 						};
 
-						bootloaderenvred@0x100000 {
+						bootloaderenvred@100000 {
 							label = "bootloader env redundant";
 							reg = <0x100000 0x40000>;
 						};
 
-						bootloaderenv@0x140000 {
+						bootloaderenv@140000 {
 							label = "bootloader env";
 							reg = <0x140000 0x40000>;
 						};
@@ -125,8 +126,6 @@
 			bus-width = <8>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sdmmc0_default>;
-			non-removable;
-			mmc-ddr-1_8v;
 			status = "okay";
 		};
 
@@ -140,6 +139,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 				status = "okay";
 
@@ -180,8 +181,11 @@
 
 			i2c0: i2c@f8028000 {
 				dmas = <0>, <0>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c0_default>;
+				pinctrl-1 = <&pinctrl_i2c0_gpio>;
+				sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 			};
 
@@ -190,27 +194,21 @@
 				status = "okay";
 
 				i2c2: i2c@600 {
-					compatible = "atmel,sama5d2-i2c";
-					reg = <0x600 0x200>;
-					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
 					dmas = <0>, <0>;
-					dma-names = "tx", "rx";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
-					pinctrl-names = "default";
+					pinctrl-names = "default", "gpio";
 					pinctrl-0 = <&pinctrl_flx0_default>;
-					atmel,fifo-size = <16>;
+					pinctrl-1 = <&pinctrl_flx0_gpio>;
+					sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
+					scl-gpios = <&pioA PIN_PB29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 					status = "okay";
 				};
 			};
 
-			shdwc@f8048010 {
-				atmel,shdwc-debouncer = <976>;
+			poweroff@f8048010 {
+				debounce-delay-us = <976>;
 
 				input@0 {
 					reg = <0>;
-					atmel,wakeup-type = "low";
 				};
 			};
 
@@ -226,8 +224,11 @@
 
 			i2c1: i2c@fc028000 {
 				dmas = <0>, <0>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c1_default>;
+				pinctrl-1 = <&pinctrl_i2c1_gpio>;
+				sda-gpios = <&pioA PIN_PC6 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA PIN_PC7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 
 				at24@50 {
@@ -244,18 +245,36 @@
 					bias-disable;
 				};
 
+				pinctrl_flx0_gpio: flx0_gpio {
+					pinmux = <PIN_PB28__GPIO>,
+						 <PIN_PB29__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_i2c0_default: i2c0_default {
 					pinmux = <PIN_PD21__TWD0>,
 						 <PIN_PD22__TWCK0>;
 					bias-disable;
 				};
 
+				pinctrl_i2c0_gpio: i2c0_gpio {
+					pinmux = <PIN_PD21__GPIO>,
+						 <PIN_PD22__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_i2c1_default: i2c1_default {
 					pinmux = <PIN_PC6__TWD1>,
 						 <PIN_PC7__TWCK1>;
 					bias-disable;
 				};
 
+				pinctrl_i2c1_gpio: i2c1_gpio {
+					pinmux = <PIN_PC6__GPIO>,
+						 <PIN_PC7__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_key_gpio_default: key_gpio_default {
 					pinmux = <PIN_PA10__GPIO>;
 					bias-pull-up;
@@ -377,16 +396,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button-1 {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>;
-			linux,code = <0x104>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
 		};
 	};
 
@@ -396,17 +416,17 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay";
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PB10 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PB6 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
index 9d0a7fbea725..6680031387e8 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
@@ -10,12 +10,20 @@
 #include "sama5d2-pinfunc.h"
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/regulator/active-semi,8945a-regulator.h>
 
 / {
 	model = "Atmel SAMA5D2 Xplained";
 	compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5";
 
+	aliases {
+		serial0 = &uart1;	/* DBGU */
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;		/* XPRO EXT2 */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -58,7 +66,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sdmmc0_default>;
 			non-removable;
-			mmc-ddr-1_8v;
+			mmc-ddr-3_3v;
 			status = "okay";
 		};
 
@@ -72,12 +80,64 @@
 		};
 
 		apb {
+			qspi0: spi@f0020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_qspi0_default>;
+				status = "disabled"; /* conflict with sdmmc1 */
+
+				flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "jedec,spi-nor";
+					reg = <0>;
+					spi-max-frequency = <80000000>;
+					spi-tx-bus-width = <4>;
+					spi-rx-bus-width = <4>;
+					m25p,fast-read;
+
+					at91bootstrap@0 {
+						label = "at91bootstrap";
+						reg = <0x00000000 0x00040000>;
+					};
+
+					bootloader@40000 {
+						label = "bootloader";
+						reg = <0x00040000 0x000c0000>;
+					};
+
+					bootloaderenvred@100000 {
+						label = "bootloader env redundant";
+						reg = <0x00100000 0x00040000>;
+					};
+
+					bootloaderenv@140000 {
+						label = "bootloader env";
+						reg = <0x00140000 0x00040000>;
+					};
+
+					dtb@180000 {
+						label = "device tree";
+						reg = <0x00180000 0x00080000>;
+					};
+
+					kernel@200000 {
+						label = "kernel";
+						reg = <0x00200000 0x00600000>;
+					};
+
+					misc@800000 {
+						label = "misc";
+						reg = <0x00800000 0x00000000>;
+					};
+				};
+			};
+
 			spi0: spi@f8000000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0_default>;
 				status = "okay";
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					reg = <0>;
 					spi-max-frequency = <50000000>;
@@ -87,6 +147,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 				status = "okay";
 
@@ -109,16 +171,6 @@
 				};
 			};
 
-			pdmic@f8018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_pdmic_default>;
-				atmel,model = "PDMIC @ sama5d2_xplained";
-				atmel,mic-min-freq = <1000000>;
-				atmel,mic-max-freq = <3246000>;
-				atmel,mic-offset = <0x0>;
-				status = "okay";
-			};
-
 			uart1: serial@f8020000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1_default>;
@@ -129,8 +181,11 @@
 
 			i2c0: i2c@f8028000 {
 				dmas = <0>, <0>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c0_default>;
+				pinctrl-1 = <&pinctrl_i2c0_gpio>;
+				sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				i2c-sda-hold-time-ns = <350>;
 				status = "okay";
 
@@ -152,10 +207,10 @@
 
 							regulator-state-mem {
 								regulator-on-in-suspend;
-								regulator-suspend-min-microvolt=<1400000>;
-								regulator-suspend-max-microvolt=<1400000>;
+								regulator-suspend-min-microvolt = <1400000>;
+								regulator-suspend-max-microvolt = <1400000>;
 								regulator-changeable-in-suspend;
-								regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+								regulator-mode = <ACT8945A_REGULATOR_MODE_LOWPOWER>;
 							};
 						};
 
@@ -272,25 +327,33 @@
 				status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
 
 				uart5: serial@200 {
-					compatible = "atmel,at91sam9260-usart";
-					reg = <0x200 0x200>;
-					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
-					clock-names = "usart";
+					dmas = <0>, <0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx0_default>;
-					atmel,fifo-size = <32>;
 					status = "okay";
 				};
+
+				i2c2: i2c@600 {
+					dmas = <0>, <0>;
+					pinctrl-names = "default", "gpio";
+					pinctrl-0 = <&pinctrl_flx0_default>;
+					pinctrl-1 = <&pinctrl_i2c2_gpio>;
+					sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
+					scl-gpios = <&pioA PIN_PB29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+					i2c-sda-hold-time-ns = <350>;
+					i2c-analog-filter;
+					i2c-digital-filter;
+					i2c-digital-filter-width-ns = <35>;
+					status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+				};
 			};
 
-			shdwc@f8048010 {
-				atmel,shdwc-debouncer = <976>;
+			poweroff@f8048010 {
+				debounce-delay-us = <976>;
 				atmel,wakeup-rtc-timer;
 
 				input@0 {
 					reg = <0>;
-					atmel,wakeup-type = "low";
 				};
 			};
 
@@ -322,18 +385,13 @@
 				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
 				status = "okay";
 
-				i2c2: i2c@600 {
-					compatible = "atmel,sama5d2-i2c";
-					reg = <0x600 0x200>;
-					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+				i2c6: i2c@600 {
 					dmas = <0>, <0>;
-					dma-names = "tx", "rx";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
-					pinctrl-names = "default";
+					pinctrl-names = "default", "gpio";
 					pinctrl-0 = <&pinctrl_flx4_default>;
-					atmel,fifo-size = <16>;
+					pinctrl-1 = <&pinctrl_flx4_gpio>;
+					sda-gpios = <&pioA PIN_PD12 GPIO_ACTIVE_HIGH>;
+					scl-gpios = <&pioA PIN_PD13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 					i2c-analog-filter;
 					i2c-digital-filter;
 					i2c-digital-filter-width-ns = <35>;
@@ -343,11 +401,14 @@
 
 			i2c1: i2c@fc028000 {
 				dmas = <0>, <0>;
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c1_default>;
 				i2c-analog-filter;
 				i2c-digital-filter;
 				i2c-digital-filter-width-ns = <35>;
+				pinctrl-1 = <&pinctrl_i2c1_gpio>;
+				sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 
 				at24@54 {
@@ -421,14 +482,18 @@
 					bias-pull-up;
 				};
 
-				pinctrl_classd_default: classd_default {
+				pinctrl_classd_default_pfets: classd_default_pfets {
 					pinmux = <PIN_PB1__CLASSD_R0>,
-						 <PIN_PB2__CLASSD_R1>,
-						 <PIN_PB3__CLASSD_R2>,
-						 <PIN_PB4__CLASSD_R3>;
+						 <PIN_PB3__CLASSD_R2>;
 					bias-pull-up;
 				};
 
+				pinctrl_classd_default_nfets: classd_default_nfets {
+					pinmux = <PIN_PB2__CLASSD_R1>,
+						 <PIN_PB4__CLASSD_R3>;
+					bias-pull-down;
+				};
+
 				pinctrl_flx0_default: flx0_default {
 					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
 						 <PIN_PB29__FLEXCOM0_IO1>;
@@ -441,18 +506,42 @@
 					bias-disable;
 				};
 
+				pinctrl_flx4_gpio: flx4_gpio {
+					pinmux = <PIN_PD12__GPIO>,
+						 <PIN_PD13__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_i2c0_default: i2c0_default {
 					pinmux = <PIN_PD21__TWD0>,
 						 <PIN_PD22__TWCK0>;
 					bias-disable;
 				};
 
+				pinctrl_i2c0_gpio: i2c0_gpio {
+					pinmux = <PIN_PD21__GPIO>,
+						 <PIN_PD22__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_i2c1_default: i2c1_default {
 					pinmux = <PIN_PD4__TWD1>,
 						 <PIN_PD5__TWCK1>;
 					bias-disable;
 				};
 
+				pinctrl_i2c1_gpio: i2c1_gpio {
+					pinmux = <PIN_PD4__GPIO>,
+						 <PIN_PD5__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_i2c2_gpio: i2c2_gpio {
+					pinmux = <PIN_PB28__GPIO>,
+						 <PIN_PB29__GPIO>;
+					bias-disable;
+				};
+
 				pinctrl_i2s0_default: i2s0_default {
 					pinmux = <PIN_PC1__I2SC0_CK>,
 						 <PIN_PC2__I2SC0_MCK>,
@@ -502,10 +591,20 @@
 					bias-disable;
 				};
 
-				pinctrl_pdmic_default: pdmic_default {
-					pinmux = <PIN_PB26__PDMIC_DAT>,
-						<PIN_PB27__PDMIC_CLK>;
-					bias-disable;
+				pinctrl_qspi0_default: qspi0_default {
+					sck_cs {
+						pinmux = <PIN_PA22__QSPI0_SCK>,
+							 <PIN_PA23__QSPI0_CS>;
+						bias-disable;
+					};
+
+					data {
+						pinmux = <PIN_PA24__QSPI0_IO0>,
+							 <PIN_PA25__QSPI0_IO1>,
+							 <PIN_PA26__QSPI0_IO2>,
+							 <PIN_PA27__QSPI0_IO3>;
+						bias-pull-up;
+					};
 				};
 
 				pinctrl_sdmmc0_default: sdmmc0_default {
@@ -522,10 +621,9 @@
 						bias-disable;
 					};
 
-					ck_cd_rstn_vddsel {
+					ck_cd_rstn {
 						pinmux = <PIN_PA0__SDMMC0_CK>,
 							 <PIN_PA10__SDMMC0_RSTN>,
-							 <PIN_PA11__SDMMC0_VDDSEL>,
 							 <PIN_PA13__SDMMC0_CD>;
 						bias-disable;
 					};
@@ -587,7 +685,7 @@
 
 			classd: classd@fc048000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_classd_default>;
+				pinctrl-0 = <&pinctrl_classd_default_pfets &pinctrl_classd_default_nfets>;
 				atmel,pwm-type = "diff";
 				atmel,non-overlap-time = <10>;
 				status = "okay";
@@ -607,16 +705,16 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
-			linux,code = <0x104>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
@@ -627,18 +725,18 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay"; /* conflict with pwm0 */
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>;
 		};
 
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d3_eds.dts b/arch/arm/boot/dts/microchip/at91-sama5d3_eds.dts
new file mode 100644
index 000000000000..c287b03d768b
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d3_eds.dts
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * at91-sama5d3_eds.dts - Device Tree file for the SAMA5D3 Ethernet
+ *    Development System board.
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Jerry Ray <jerry.ray@microchip.com>
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "SAMA5D3 Ethernet Development System";
+	compatible = "microchip,sama5d3-eds", "atmel,sama5d36",
+		     "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio>;
+
+		button-3 {
+			label = "PB_USER";
+			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x104>;
+			wakeup-source;
+		};
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	vcc_3v3_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vcc_2v5_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_2V5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+
+	vcc_1v8_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+
+	vcc_1v2_reg: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
+
+	vcc_mmc0_reg: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc0-card-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
+		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can0 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand_controller: nand-controller {
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x2>;
+			atmel,rb = <0>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <4>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				bootloader@40000 {
+					label = "bootloader";
+					reg = <0x40000 0xc0000>;
+				};
+
+				bootloaderenvred@100000 {
+					label = "bootloader env redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				bootloaderenv@140000 {
+					label = "bootloader env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x0f800000>;
+				};
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&pinctrl_i2c0_pu>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&pinctrl_i2c2_pu>;
+	status = "okay";
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&mmc0 {
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
+		     &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+	vmmc-supply = <&vcc_mmc0_reg>;
+	vqmmc-supply = <&vcc_3v3_reg>;
+	status = "okay";
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+		cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_i2c0_pu: i2c0-pu {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_i2c2_pu: i2c2-pu {
+			atmel,pins =
+				<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_key_gpio: key-gpio-0 {
+			atmel,pins =
+				<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		pinctrl_mmc0_cd: mmc0-cd {
+			atmel,pins =
+				<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		/* Reserved for reset signal to the RGMII connector. */
+		pinctrl_rgmii_rstn: rgmii-rstn {
+			atmel,pins =
+				<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		/* Reserved for an interrupt line from the RMII and RGMII connectors. */
+		pinctrl_spi_irqn: spi-irqn {
+			atmel,pins =
+				<AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_spi0_cs: spi0-cs-default {
+			atmel,pins =
+				<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				 AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi1_cs: spi1-cs-default {
+			atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOC 28 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins =
+				<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_usb_default: usb-default {
+			atmel,pins =
+				<AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				 AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		/* Reserved for VBUS fault interrupt. */
+		pinctrl_vbusfault_irqn: vbusfault-irqn {
+			atmel,pins =
+				<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_vcc_mmc0_reg_gpio: vcc-mmc0-reg-gpio-default {
+			atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&spi0 {
+	pinctrl-names = "default", "cs";
+	pinctrl-1 = <&pinctrl_spi0_cs>;
+	cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default", "cs";
+	pinctrl-1 = <&pinctrl_spi1_cs>;
+	cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioC 28 0>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {	/* USB Device port with VBUS detection. */
+	atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {	/* 3-port Host. First port is unused. */
+	atmel,vbus-gpio = <0
+			   &pioE 3 GPIO_ACTIVE_HIGH
+			   &pioE 4 GPIO_ACTIVE_HIGH
+			  >;
+	num-ports = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d3_ksz9477_evb.dts b/arch/arm/boot/dts/microchip/at91-sama5d3_ksz9477_evb.dts
new file mode 100644
index 000000000000..b66570080894
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d3_ksz9477_evb.dts
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "EVB-KSZ9477";
+	compatible = "microchip,sama5d3-ksz9477-evb", "atmel,sama5d36",
+		     "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = &dbgu;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vcc_mmc0: regulator-mmc0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mcc0_vcc>;
+		regulator-name = "mmc0-vcc";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&pinctrl_i2c0_pu>;
+	status = "okay";
+};
+
+&macb0 {
+	phy-mode = "rgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&mmc0 {
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
+		     &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+	status = "okay";
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+		cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+		disable-wp;
+		vmmc-supply = <&reg_vcc_mmc0>;
+		vqmmc-supply = <&reg_3v3>;
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@3 {
+		reg = <0x3 0x0 0x2>;
+		atmel,rb = <0>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&spi0 {
+	cs-gpios = <&pioD 13 GPIO_ACTIVE_LOW>, <0>, <0>,
+		   <&pioD 16 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-0 = <&pinctrl_spi_ksz>;
+	cs-gpios = <&pioC 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	switch@0 {
+		compatible = "microchip,ksz9477";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cpha;
+		spi-cpol;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan1";
+				phy-mode = "internal";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan2";
+				phy-mode = "internal";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan3";
+				phy-mode = "internal";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan4";
+				phy-mode = "internal";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan5";
+				phy-mode = "internal";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&macb0>;
+				phy-mode = "rgmii-txid";
+				tx-internal-delay-ps = <2000>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&pinctrl {
+	board {
+		pinctrl_i2c0_pu: i2c0-pu {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_mmc0_cd: mmc0-cd {
+			atmel,pins = <AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_mcc0_vcc: mmc0-vcc {
+			atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi_ksz: spi-ksz {
+			atmel,pins =
+				<
+				/* SPI1_MISO */
+				AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				/* SPI1_MOSI */
+				AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE
+				/* SPI1_SPCK */
+				AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE
+
+				/* SPI CS */
+				AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				/* switch IRQ */
+				AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH
+				/* switch PME_N, SoC IN */
+				AT91_PIOC 30 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP
+				/* switch RST */
+				AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH
+				>;
+		};
+
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins =
+				<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d3_xplained.dts
index 61f068a7b362..820033727088 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d3_xplained.dts
@@ -7,6 +7,7 @@
  */
 /dts-v1/;
 #include "sama5d36.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "SAMA5D3 Xplained";
@@ -16,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x10000000>;
 	};
 
@@ -56,6 +57,8 @@
 			};
 
 			spi0: spi@f0004000 {
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi0_cs>;
 				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
 			};
@@ -128,7 +131,7 @@
 			};
 
 			macb0: ethernet@f0028000 {
-				phy-mode = "rgmii";
+				phy-mode = "rgmii-rxid";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "okay";
@@ -168,6 +171,8 @@
 			};
 
 			spi1: spi@f8008000 {
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioC 25 0>;
 				status = "okay";
 			};
@@ -242,6 +247,31 @@
 						atmel,pins =
 							<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PE9, conflicts with A9 */
 					};
+					pinctrl_usb_default: usb_default {
+						atmel,pins =
+							<AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_gpio_leds: gpio_leds_default {
+						atmel,pins =
+							<AT91_PIOE 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_spi0_cs: spi0_cs_default {
+						atmel,pins =
+							<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_spi1_cs: spi1_cs_default {
+						atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_vcc_mmc0_reg_gpio: vcc_mmc0_reg_gpio_default {
+						atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 			};
 		};
@@ -259,6 +289,8 @@
 					   &pioE 3 GPIO_ACTIVE_LOW
 					   &pioE 4 GPIO_ACTIVE_LOW
 					  >;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
 			status = "okay";
 		};
 
@@ -331,6 +363,8 @@
 
 	vcc_mmc0_reg: fixedregulator_mmc0 {
 		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
 		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
 		regulator-name = "mmc0-card-supply";
 		regulator-min-microvolt = <3300000>;
@@ -338,31 +372,34 @@
 		regulator-always-on;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		bp3 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
-			linux,code = <0x104>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+		status = "okay";
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioE 23 GPIO_ACTIVE_LOW>;	/* PE23, conflicts with A23, CTS2 */
 			linux,default-trigger = "heartbeat";
 		};
 
-		d3 {
-			label = "d3";
+		led-d3 {
+			label = "d3"; /* Conflict with EBI CS0, USART2 CTS. */
 			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
 		};
 	};
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4.dtsi
index 0be184a870eb..fd1086f52b40 100644
--- a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4.dtsi
@@ -9,7 +9,7 @@
 	model = "Aries/DENX MA5D4";
 	compatible = "aries,ma5d4", "denx,ma5d4", "atmel,sama5d4", "atmel,sama5";
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x10000000>;
 	};
 
@@ -49,7 +49,7 @@
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4evk.dts
index af4969485c88..8adf567f2f0f 100644
--- a/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4evk.dts
@@ -115,19 +115,19 @@
 		compatible = "gpio-leds";
 		status = "okay";
 
-		user1 {
+		led-user1 {
 			label = "user1";
 			gpios = <&pioD 28 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		user2 {
+		led-user2 {
 			label = "user2";
 			gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		user3 {
+		led-user3 {
 			label = "user3";
 			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -136,7 +136,7 @@
 
 	panel: panel {
 		/* Actually Ampire 800480R2 */
-		compatible = "foxlink,fl500wvr00-a0t", "simple-panel";
+		compatible = "foxlink,fl500wvr00-a0t";
 		backlight = <&backlight>;
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d4_xplained.dts
index 924d9491780d..95d701d13fef 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4_xplained.dts
@@ -7,6 +7,7 @@
  */
 /dts-v1/;
 #include "sama5d4.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Atmel SAMA5D4 Xplained";
@@ -16,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x20000000>;
 	};
 
@@ -38,16 +39,6 @@
 				status = "okay";
 			};
 
-			spi0: spi@f8010000 {
-				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
-				status = "okay";
-				m25p80@0 {
-					compatible = "atmel,at25df321a";
-					spi-max-frequency = <50000000>;
-					reg = <0>;
-				};
-			};
-
 			i2c0: i2c@f8014000 {
 				i2c-digital-filter;
 				status = "okay";
@@ -90,6 +81,8 @@
 			};
 
 			spi1: spi@fc018000 {
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioB 21 0>;
 				status = "okay";
 			};
@@ -134,6 +127,11 @@
 						atmel,pins =
 							<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
 					};
+					pinctrl_usb_default: usb_default {
+						atmel,pins =
+							<AT91_PIOE 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOE 14 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 					pinctrl_key_gpio: key_gpio_0 {
 						atmel,pins =
 							<AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
@@ -142,6 +140,19 @@
 						atmel,pins =
 							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
 					};
+					pinctrl_spi1_cs: spi1_cs_default {
+						atmel,pins =
+							<AT91_PIOB 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+					pinctrl_gpio_leds: gpio_leds_default {
+						atmel,pins =
+							<AT91_PIOD 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOE 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+					pinctrl_vcc_mmc1_reg: vcc_mmc1_reg {
+						atmel,pins =
+							<AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 			};
 		};
@@ -159,6 +170,8 @@
 					   &pioE 11 GPIO_ACTIVE_HIGH
 					   &pioE 14 GPIO_ACTIVE_HIGH
 					  >;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
 			status = "okay";
 		};
 
@@ -229,31 +242,33 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		pb_user1 {
+		button {
 			label = "pb_user1";
 			gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
-			linux,code = <0x100>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
 		status = "okay";
 
-		d8 {
+		led-d8 {
 			label = "d8";
 			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		d10 {
+		led-d10 {
 			label = "d10";
 			gpios = <&pioE 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
@@ -271,6 +286,8 @@
 
 	vcc_mmc1_reg: fixedregulator_mmc1 {
 		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc1_reg>;
 		gpio = <&pioE 4 GPIO_ACTIVE_LOW>;
 		regulator-name = "VDD MCI1";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d4ek.dts
index 0cc1cff13e46..20ac775059ca 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4ek.dts
@@ -16,7 +16,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x20000000>;
 	};
 
@@ -65,7 +65,7 @@
 			spi0: spi@f8010000 {
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -269,13 +269,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		pb_user1 {
+		button {
 			label = "pb_user1";
 			gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
@@ -287,18 +287,18 @@
 		compatible = "gpio-leds";
 		status = "okay";
 
-		d8 {
+		led-d8 {
 			label = "d8";
 			/* PE28, conflicts with usart4 rts pin */
 			gpios = <&pioE 28 GPIO_ACTIVE_LOW>;
 		};
 
-		d9 {
+		led-d9 {
 			label = "d9";
 			gpios = <&pioE 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		d10 {
+		led-d10 {
 			label = "d10";
 			gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91-sama7g5ek.dts b/arch/arm/boot/dts/microchip/at91-sama7g5ek.dts
new file mode 100644
index 000000000000..217e9b96c61e
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama7g5ek.dts
@@ -0,0 +1,834 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ *  at91-sama7g5ek.dts - Device Tree file for SAMA7G5-EK board
+ *
+ *  Copyright (c) 2020 Microchip Technology Inc. and its subsidiaries
+ *
+ *  Author: Eugen Hristev <eugen.hristev@microchip.com>
+ *  Author: Claudiu Beznea <claudiu.beznea@microchip.com>
+ *
+ */
+/dts-v1/;
+#include "sama7g5-pinfunc.h"
+#include "sama7g5.dtsi"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/sound/microchip,pdmc.h>
+
+/ {
+	model = "Microchip SAMA7G5-EK";
+	compatible = "microchip,sama7g5ek", "microchip,sama7g5", "microchip,sama7";
+
+	chosen {
+		bootargs = "rw root=/dev/mmcblk1p2 rootfstype=ext4 rootwait";
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart3;
+		serial1 = &uart4;
+		serial2 = &uart7;
+		serial3 = &uart0;
+		i2c0 = &i2c1;
+		i2c1 = &i2c8;
+		i2c2 = &i2c9;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button {
+			label = "PB_USER";
+			gpios = <&pioA PIN_PA12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay"; /* Conflict with pwm. */
+
+		red_led {
+			label = "red";
+			gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
+		};
+
+		green_led {
+			label = "green";
+			gpios = <&pioA PIN_PA13 GPIO_ACTIVE_HIGH>;
+		};
+
+		blue_led {
+			label = "blue";
+			gpios = <&pioA PIN_PD20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	/* 512 M */
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x20000000>;
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "sama7g5ek audio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			cpu {
+				sound-dai = <&spdiftx>;
+			};
+			codec {
+				sound-dai = <&spdif_out>;
+			};
+		};
+		simple-audio-card,dai-link@1 {
+			reg = <1>;
+			cpu {
+				sound-dai = <&spdifrx>;
+			};
+			codec {
+				sound-dai = <&spdif_in>;
+			};
+		};
+	};
+
+	spdif_in: spdif-in {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dir";
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+};
+
+&adc {
+	vddana-supply = <&vddout25>;
+	vref-supply = <&vddout25>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_an_default &pinctrl_mikrobus2_an_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+};
+
+&qspi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <133000000>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		m25p,fast-read;
+
+		at91bootstrap@0 {
+			label = "ospi: at91bootstrap";
+			reg = <0x0 0x40000>;
+		};
+
+		bootloader@40000 {
+			label = "ospi: bootloader";
+			reg = <0x40000 0xc0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "ospi: bootloader env redundant";
+			reg = <0x100000 0x40000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "ospi: bootloader env";
+			reg = <0x140000 0x40000>;
+		};
+
+		dtb@180000 {
+			label = "ospi: device tree";
+			reg = <0x180000 0x80000>;
+		};
+
+		kernel@200000 {
+			label = "ospi: kernel";
+			reg = <0x200000 0x600000>;
+		};
+
+		rootfs@800000 {
+			label = "ospi: rootfs";
+			reg = <0x800000 0x7800000>;
+		};
+
+	};
+};
+
+&dma0 {
+	status = "okay";
+};
+
+&dma1 {
+	status = "okay";
+};
+
+&dma2 {
+	status = "okay";
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "disabled";
+
+	uart0: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		status = "disabled";
+	};
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c1: i2c@600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c1_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		mcp16502@5b {
+			compatible = "microchip,mcp16502";
+			reg = <0x5b>;
+			status = "okay";
+
+			regulators {
+				vdd_3v3: VDD_IO {
+					regulator-name = "VDD_IO";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <3300000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				vddioddr: VDD_DDR {
+					regulator-name = "VDD_DDR";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1350000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1350000>;
+						regulator-mode = <4>;
+					};
+				};
+
+				vddcore: VDD_CORE {
+					regulator-name = "VDD_CORE";
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-voltage = <1150000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				vddcpu: VDD_OTHER {
+					regulator-name = "VDD_OTHER";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-ramp-delay = <3125>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-voltage = <1050000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				vldo1: LDO1 {
+					regulator-name = "LDO1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-suspend-voltage = <1800000>;
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				vldo2: LDO2 {
+					regulator-name = "LDO2";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <3700000>;
+
+					regulator-state-standby {
+						regulator-suspend-voltage = <1800000>;
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+			};
+		};
+	};
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart3: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx3_default>;
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart4: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx4_default>;
+		status = "okay";
+	};
+};
+
+&flx7 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart7: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx7_default>;
+		status = "okay";
+	};
+};
+
+&flx8 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c8: i2c@600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c8_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+	};
+};
+
+&flx9 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c9: i2c@600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c9_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+	};
+};
+
+&flx11 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi11: spi@400 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mikrobus1_spi &pinctrl_mikrobus1_spi_cs>;
+		status = "okay";
+	};
+};
+
+&gmac0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gmac0_default
+		     &pinctrl_gmac0_mdio_default
+		     &pinctrl_gmac0_txck_default
+		     &pinctrl_gmac0_phy_irq>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	ethernet-phy@7 {
+		reg = <0x7>;
+		interrupt-parent = <&pioA>;
+		interrupts = <PIN_PA31 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&gmac1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gmac1_default
+		     &pinctrl_gmac1_mdio_default
+		     &pinctrl_gmac1_phy_irq>;
+	phy-mode = "rmii";
+	status = "okay"; /* Conflict with pdmc0. */
+
+	ethernet-phy@0 {
+		reg = <0x0>;
+		interrupt-parent = <&pioA>;
+		interrupts = <PIN_PA21 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2s0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2s0_default>;
+};
+
+&pdmc0 {
+	#sound-dai-cells = <0>;
+	microchip,mic-pos = <MCHP_PDMC_DS0 MCHP_PDMC_CLK_NEGATIVE>, /* MIC 1 */
+			    <MCHP_PDMC_DS1 MCHP_PDMC_CLK_NEGATIVE>, /* MIC 2 */
+			    <MCHP_PDMC_DS0 MCHP_PDMC_CLK_POSITIVE>, /* MIC 3 */
+			    <MCHP_PDMC_DS1 MCHP_PDMC_CLK_POSITIVE>; /* MIC 4 */
+	status = "disabled"; /* Conflict with gmac1. */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pdmc0_default>;
+};
+
+&pioA {
+
+	pinctrl_can0_default: can0_default {
+		pinmux = <PIN_PD12__CANTX0>,
+			 <PIN_PD13__CANRX0 >;
+		bias-disable;
+	};
+
+	pinctrl_can1_default: can1_default {
+		pinmux = <PIN_PD14__CANTX1>,
+			 <PIN_PD15__CANRX1 >;
+		bias-disable;
+	};
+
+	pinctrl_flx0_default: flx0_default {
+		pinmux = <PIN_PE3__FLEXCOM0_IO0>,
+			 <PIN_PE4__FLEXCOM0_IO1>,
+			 <PIN_PE6__FLEXCOM0_IO3>,
+			 <PIN_PE7__FLEXCOM0_IO4>;
+		bias-disable;
+	};
+
+	pinctrl_flx3_default: flx3_default {
+		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
+			 <PIN_PD17__FLEXCOM3_IO1>;
+		bias-pull-up;
+	};
+
+	pinctrl_flx4_default: flx4_default {
+		pinmux = <PIN_PD18__FLEXCOM4_IO0>,
+			 <PIN_PD19__FLEXCOM4_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_flx7_default: flx7_default {
+		pinmux = <PIN_PC23__FLEXCOM7_IO0>,
+			 <PIN_PC24__FLEXCOM7_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_default: gmac0_default {
+		pinmux = <PIN_PA16__G0_TX0>,
+			 <PIN_PA17__G0_TX1>,
+			 <PIN_PA26__G0_TX2>,
+			 <PIN_PA27__G0_TX3>,
+			 <PIN_PA19__G0_RX0>,
+			 <PIN_PA20__G0_RX1>,
+			 <PIN_PA28__G0_RX2>,
+			 <PIN_PA29__G0_RX3>,
+			 <PIN_PA15__G0_TXEN>,
+			 <PIN_PA30__G0_RXCK>,
+			 <PIN_PA18__G0_RXDV>,
+			 <PIN_PA25__G0_125CK>;
+		slew-rate = <0>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_mdio_default: gmac0_mdio_default {
+		pinmux = <PIN_PA22__G0_MDC>,
+			 <PIN_PA23__G0_MDIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_txck_default: gmac0_txck_default {
+		pinmux = <PIN_PA24__G0_TXCK>;
+		slew-rate = <0>;
+		bias-pull-up;
+	};
+
+	pinctrl_gmac0_phy_irq: gmac0_phy_irq {
+		pinmux = <PIN_PA31__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac1_default: gmac1_default {
+		pinmux = <PIN_PD30__G1_TXCK>,
+			 <PIN_PD22__G1_TX0>,
+			 <PIN_PD23__G1_TX1>,
+			 <PIN_PD21__G1_TXEN>,
+			 <PIN_PD25__G1_RX0>,
+			 <PIN_PD26__G1_RX1>,
+			 <PIN_PD27__G1_RXER>,
+			 <PIN_PD24__G1_RXDV>;
+		slew-rate = <0>;
+		bias-disable;
+	};
+
+	pinctrl_gmac1_mdio_default: gmac1_mdio_default {
+		pinmux = <PIN_PD28__G1_MDC>,
+			 <PIN_PD29__G1_MDIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac1_phy_irq: gmac1_phy_irq {
+		pinmux = <PIN_PA21__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_default: i2c1_default {
+		pinmux = <PIN_PC9__FLEXCOM1_IO0>,
+			 <PIN_PC10__FLEXCOM1_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c8_default: i2c8_default {
+		pinmux = <PIN_PC14__FLEXCOM8_IO0>,
+			 <PIN_PC13__FLEXCOM8_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c9_default: i2c9_default {
+		pinmux = <PIN_PC18__FLEXCOM9_IO0>,
+			 <PIN_PC19__FLEXCOM9_IO1>;
+		bias-disable;
+	};
+
+	pinctrl_i2s0_default: i2s0_default {
+		pinmux = <PIN_PB23__I2SMCC0_CK>,
+			 <PIN_PB24__I2SMCC0_WS>,
+			 <PIN_PB25__I2SMCC0_DOUT1>,
+			 <PIN_PB26__I2SMCC0_DOUT0>,
+			 <PIN_PB27__I2SMCC0_MCK>;
+		bias-disable;
+	};
+
+	pinctrl_key_gpio_default: key_gpio_default {
+		pinmux = <PIN_PA12__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led_gpio_default {
+		pinmux = <PIN_PA13__GPIO>,
+			 <PIN_PB8__GPIO>,
+			 <PIN_PD20__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_mikrobus1_an_default: mikrobus1_an_default {
+		pinmux = <PIN_PD0__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_an_default: mikrobus2_an_default {
+		pinmux = <PIN_PD1__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_pwm2_default: mikrobus1_pwm2_default {
+		pinmux = <PIN_PA13__PWMH2>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_pwm3_default: mikrobus2_pwm3_default {
+		pinmux = <PIN_PD20__PWMH3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_spi_cs: mikrobus1_spi_cs {
+		pinmux = <PIN_PB6__FLEXCOM11_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_spi: mikrobus1_spi {
+		pinmux = <PIN_PB3__FLEXCOM11_IO0>,
+			 <PIN_PB4__FLEXCOM11_IO1>,
+			 <PIN_PB5__FLEXCOM11_IO2>;
+		bias-disable;
+	};
+
+	pinctrl_pdmc0_default: pdmc0_default {
+		pinmux = <PIN_PD23__PDMC0_DS0>,
+			 <PIN_PD24__PDMC0_DS1>,
+			 <PIN_PD22__PDMC0_CLK>;
+		bias_disable;
+	};
+
+	pinctrl_qspi: qspi {
+		pinmux = <PIN_PB12__QSPI0_IO0>,
+			 <PIN_PB11__QSPI0_IO1>,
+			 <PIN_PB10__QSPI0_IO2>,
+			 <PIN_PB9__QSPI0_IO3>,
+			 <PIN_PB16__QSPI0_IO4>,
+			 <PIN_PB17__QSPI0_IO5>,
+			 <PIN_PB18__QSPI0_IO6>,
+			 <PIN_PB19__QSPI0_IO7>,
+			 <PIN_PB13__QSPI0_CS>,
+			 <PIN_PB14__QSPI0_SCK>,
+			 <PIN_PB15__QSPI0_SCKN>,
+			 <PIN_PB20__QSPI0_DQS>,
+			 <PIN_PB21__QSPI0_INT>;
+		bias-disable;
+		slew-rate = <0>;
+		atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0_default {
+		cmd_data {
+			pinmux = <PIN_PA1__SDMMC0_CMD>,
+				 <PIN_PA3__SDMMC0_DAT0>,
+				 <PIN_PA4__SDMMC0_DAT1>,
+				 <PIN_PA5__SDMMC0_DAT2>,
+				 <PIN_PA6__SDMMC0_DAT3>,
+				 <PIN_PA7__SDMMC0_DAT4>,
+				 <PIN_PA8__SDMMC0_DAT5>,
+				 <PIN_PA9__SDMMC0_DAT6>,
+				 <PIN_PA10__SDMMC0_DAT7>;
+			slew-rate = <0>;
+			bias-pull-up;
+		};
+
+		ck_cd_rstn_vddsel {
+			pinmux = <PIN_PA0__SDMMC0_CK>,
+				 <PIN_PA2__SDMMC0_RSTN>,
+				 <PIN_PA11__SDMMC0_DS>;
+			slew-rate = <0>;
+			bias-pull-up;
+		};
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1_default {
+		cmd_data {
+			pinmux = <PIN_PB29__SDMMC1_CMD>,
+				 <PIN_PB31__SDMMC1_DAT0>,
+				 <PIN_PC0__SDMMC1_DAT1>,
+				 <PIN_PC1__SDMMC1_DAT2>,
+				 <PIN_PC2__SDMMC1_DAT3>;
+			slew-rate = <0>;
+			bias-pull-up;
+		};
+
+		ck_cd_rstn_vddsel {
+			pinmux = <PIN_PB30__SDMMC1_CK>,
+				 <PIN_PB28__SDMMC1_RSTN>,
+				 <PIN_PC5__SDMMC1_1V8SEL>,
+				 <PIN_PC4__SDMMC1_CD>;
+			slew-rate = <0>;
+			bias-pull-up;
+		};
+	};
+
+	pinctrl_sdmmc2_default: sdmmc2_default {
+		cmd_data {
+			pinmux = <PIN_PD3__SDMMC2_CMD>,
+				 <PIN_PD5__SDMMC2_DAT0>,
+				 <PIN_PD6__SDMMC2_DAT1>,
+				 <PIN_PD7__SDMMC2_DAT2>,
+				 <PIN_PD8__SDMMC2_DAT3>;
+			slew-rate = <0>;
+			bias-pull-up;
+		};
+
+		ck {
+			pinmux = <PIN_PD4__SDMMC2_CK>;
+			slew-rate = <0>;
+			bias-pull-up;
+		};
+	};
+
+	pinctrl_spdifrx_default: spdifrx_default {
+		pinmux = <PIN_PB0__SPDIF_RX>;
+		bias-disable;
+	};
+
+	pinctrl_spdiftx_default: spdiftx_default {
+		pinmux = <PIN_PB1__SPDIF_TX>;
+		bias-disable;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_pwm2_default &pinctrl_mikrobus2_pwm3_default>;
+	status = "disabled"; /* Conflict with leds. */
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc0 {
+	bus-width = <8>;
+	non-removable;
+	sdhci-caps-mask = <0x0 0x00200000>;
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vldo1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	no-1-8-v;
+	sdhci-caps-mask = <0x0 0x00200000>;
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vdd_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	bus-width = <4>;
+	no-1-8-v;
+	sdhci-caps-mask = <0x0 0x00200000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc2_default>;
+};
+
+&shdwc {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&spdifrx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdifrx_default>;
+	status = "okay";
+};
+
+&spdiftx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdiftx_default>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&vddout25 {
+	vin-supply = <&vdd_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/at91-smartkiz.dts b/arch/arm/boot/dts/microchip/at91-smartkiz.dts
new file mode 100644
index 000000000000..b76a6b5ac464
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-smartkiz.dts
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017-2018 Overkiz SAS
+ *   Author: Mickael Gardet <m.gardet@overkiz.com>
+ *           Kévin Raymond <k.raymond@overkiz.com>
+ *           Dorian Rocipon <d.rocipon@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+	model = "Overkiz SmartKiz";
+	compatible = "overkiz,smartkiz", "atmel,at91sam9g25",
+		     "atmel,at91sam9x5", "atmel,at91sam9";
+
+	clocks {
+		adc_op_clk {
+			status = "okay";
+		};
+	};
+
+	aliases {
+		serial5 = &uart0;
+	};
+
+	pio_keys {
+		hk_reset {
+			label = "HK_RESET";
+			gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_rf {
+			label = "POWER_RF";
+			gpios = <&pioA 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_wifi {
+			label = "POWER_WIFI";
+			gpios = <&pioA 21 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	i2c1 {
+		pinctrl_i2c1: i2c1-0 {
+			atmel,pins =
+				<AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_PULL_UP
+				AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	adc0 {
+		pinctrl_adc0_ad0: adc0_ad0-0 {
+			/* pull-up disable */
+			atmel,pins = <AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_adc0_ad5: adc0_ad5-0 {
+			/* pull-up disable */
+			atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_adc0_ad6: adc0_ad6-0 {
+			/* pull-up disable */
+			atmel,pins = <AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_adc0_ad11: adc0_ad11-0 {
+			/* pull-up disable */
+			atmel,pins = <AT91_PIOB 10 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+};
+
+&i2c1 {
+	dmas = <0>, <0>;
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "disabled";
+};
+
+&macb0 {
+	status = "disabled";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&led_blue {
+	status = "okay";
+};
+
+&adc0 {
+	atmel,adc-vref = <2500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_adc0_ad0
+		&pinctrl_adc0_ad5
+		&pinctrl_adc0_ad6
+		&pinctrl_adc0_ad11
+	>;
+	atmel,adc-channels-used = <0x0861>;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/at91-som60.dtsi b/arch/arm/boot/dts/microchip/at91-som60.dtsi
index 241682a207c5..39474a112b16 100644
--- a/arch/arm/boot/dts/at91-som60.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-som60.dtsi
@@ -16,7 +16,7 @@
 		stdout-path = &dbgu;
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x8000000>;
 	};
 
diff --git a/arch/arm/boot/dts/at91-tse850-3.dts b/arch/arm/boot/dts/microchip/at91-tse850-3.dts
index 3ca97b47c69c..9d58a3931207 100644
--- a/arch/arm/boot/dts/at91-tse850-3.dts
+++ b/arch/arm/boot/dts/microchip/at91-tse850-3.dts
@@ -106,35 +106,35 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ch1-red {
+		led-ch1-red {
 			label = "ch-1:red";
 			gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
 		};
-		ch1-green {
+		led-ch1-green {
 			label = "ch-1:green";
 			gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
 		};
-		ch2-red {
+		led-ch2-red {
 			label = "ch-2:red";
 			gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
 		};
-		ch2-green {
+		led-ch2-green {
 			label = "ch-2:green";
 			gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
 		};
-		data-red {
+		led-data-red {
 			label = "data:red";
 			gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
 		};
-		data-green {
+		led-data-green {
 			label = "data:green";
 			gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
 		};
-		alarm-red {
+		led-alarm-red {
 			label = "alarm:red";
 			gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
 		};
-		alarm-green {
+		led-alarm-green {
 			label = "alarm:green";
 			gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
 		};
@@ -262,7 +262,7 @@
 &macb1 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rmii";
 
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -300,3 +300,63 @@
 
 	dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
 };
+
+&pioA {
+	gpio-line-names =
+	/*  0 */	"SUP-A", "SUP-B", "SUP-C", "SIG<LEV",
+	/*  4 */	"", "/RFRST", "", "",
+	/*  8 */	"/ADD", "", "/LOOP1", "/LOOP2",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"LED1GREEN", "LED1RED", "LED2GREEN", "LED2RED",
+	/* 20 */	"LED3GREEN", "LED3RED", "LED4GREEN", "LED4RED",
+	/* 24 */	"", "", "", "",
+	/* 28 */	"", "", "SDA", "SCL";
+};
+
+&pioB {
+	gpio-line-names =
+	/*  0 */	"", "", "", "",
+	/*  4 */	"", "", "", "",
+	/*  8 */	"", "", "", "",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"", "", "", "",
+	/* 20 */	"", "", "", "",
+	/* 24 */	"", "", "SIG<LIN", "SIG>LIN",
+	/* 28 */	"RXD", "TXD", "BRX", "BTX";
+};
+
+&pioC {
+	gpio-line-names =
+	/*  0 */	"ETX0", "ETX1", "ERX0", "ERX1",
+	/*  4 */	"ETXEN", "ECRSDV", "ERXER", "EREFCK",
+	/*  8 */	"EMDC", "EMDIO", "", "",
+	/* 12 */	"", "", "", "/ILIM",
+	/* 16 */	"BCK", "LRCK", "DIN", "",
+	/* 20 */	"", "", "", "",
+	/* 24 */	"", "", "", "",
+	/* 28 */	"", "", "", "VBUS";
+};
+
+&pioD {
+	gpio-line-names =
+	/*  0 */	"I1", "I2", "O1", "EXTVEN",
+	/*  4 */	"", "456KHZ", "VCTRL", "SYNCSEL",
+	/*  8 */	"STEREO", "", "", "",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"", ">LIN", "LIN>", "",
+	/* 20 */	"VREFEN", "", "", "",
+	/* 24 */	"", "", "VINOK", "",
+	/* 28 */	"POEOK", "USBON", "POELOAD", "";
+};
+
+&pioE {
+	gpio-line-names =
+	/*  0 */	"", "", "", "",
+	/*  4 */	"", "", "", "",
+	/*  8 */	"", "", "", "",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"", "", "", "",
+	/* 20 */	"", "ALE", "CLE", "",
+	/* 24 */	"", "", "", "",
+	/* 28 */	"", "", "", "/ETHINT";
+};
diff --git a/arch/arm/boot/dts/at91-vinco.dts b/arch/arm/boot/dts/microchip/at91-vinco.dts
index 15050fdd479d..ecbdacf48708 100644
--- a/arch/arm/boot/dts/at91-vinco.dts
+++ b/arch/arm/boot/dts/microchip/at91-vinco.dts
@@ -17,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -59,7 +59,7 @@
 			spi0: spi@f8010000 {
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
-				m25p80@0 {
+				flash@0 {
 					compatible = "n25q32b", "jedec,spi-nor";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -159,7 +159,7 @@
 			atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usba_vbus>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		usb1: ohci@500000 {
@@ -168,7 +168,7 @@
 					   &pioE 11 GPIO_ACTIVE_LOW
 					   &pioE 12 GPIO_ACTIVE_LOW
 					  >;
-			status = "disable";
+			status = "disabled";
 		};
 
 		usb2: ehci@600000 {
diff --git a/arch/arm/boot/dts/at91-wb45n.dts b/arch/arm/boot/dts/microchip/at91-wb45n.dts
index 54d130c92185..ef73f727f7bd 100644
--- a/arch/arm/boot/dts/at91-wb45n.dts
+++ b/arch/arm/boot/dts/microchip/at91-wb45n.dts
@@ -12,13 +12,10 @@
 	model = "Laird Workgroup Bridge 45N - Atmel AT91SAM (dt)";
 	compatible = "laird,wb45n", "laird,wbxx", "atmel,at91sam9x5", "atmel,at91sam9";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		irqbtn@18 {
-			reg = <18>;
+		button {
 			label = "IRQBTN";
 			linux,code = <99>;
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/at91-wb45n.dtsi b/arch/arm/boot/dts/microchip/at91-wb45n.dtsi
index ebe61a25ca96..430c75358086 100644
--- a/arch/arm/boot/dts/at91-wb45n.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-wb45n.dtsi
@@ -17,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -145,6 +145,7 @@
 };
 
 &mmc0 {
+	pinctrl-names = "default";
 	pinctrl-0 = <
 		&pinctrl_mmc0_slot0_clk_cmd_dat0
 		&pinctrl_mmc0_slot0_dat1_3>;
diff --git a/arch/arm/boot/dts/at91-wb50n.dts b/arch/arm/boot/dts/microchip/at91-wb50n.dts
index a5e45bb95c04..ec2becf6133b 100644
--- a/arch/arm/boot/dts/at91-wb50n.dts
+++ b/arch/arm/boot/dts/microchip/at91-wb50n.dts
@@ -13,21 +13,17 @@
 	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
 	compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		btn0@10 {
-			reg = <10>;
+		button-0 {
 			label = "BTNESC";
 			linux,code = <1>; /* ESC button */
 			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		irqbtn@31 {
-			reg = <31>;
+		button-1 {
 			label = "IRQBTN";
 			linux,code = <99>; /* SysReq button */
 			gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
@@ -90,12 +86,6 @@
 
 &spi1 {
 	status = "okay";
-
-	spidev@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <8000000>;
-	};
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/at91-wb50n.dtsi b/arch/arm/boot/dts/microchip/at91-wb50n.dtsi
index 4ed8500a5cb8..74b249bb6351 100644
--- a/arch/arm/boot/dts/at91-wb50n.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-wb50n.dtsi
@@ -17,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 };
@@ -46,10 +46,6 @@
 	atmel,osc-bypass;
 };
 
-&usart1_clk {
-	atmel,clk-output-range = <0 132000000>;
-};
-
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/microchip/at91rm9200.dtsi
index 44385718d9d4..16c675e3a890 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/microchip/at91rm9200.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -39,16 +40,17 @@
 		ssc2 = &ssc2;
 	};
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm920t";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x04000000>;
 	};
@@ -70,6 +72,9 @@
 	sram: sram@200000 {
 		compatible = "mmio-sram";
 		reg = <0x00200000 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00200000 0x4000>;
 	};
 
 	ahb {
@@ -97,263 +102,13 @@
 				reg = <0xffffff00 0x100>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91rm9200-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				#interrupt-cells = <1>;
-
-				main_osc: main_osc {
-					compatible = "atmel,at91rm9200-clk-main-osc";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clocks = <&main_xtal>;
-				};
-
-				main: mainck {
-					compatible = "atmel,at91rm9200-clk-main";
-					#clock-cells = <0>;
-					clocks = <&main_osc>;
-				};
-
-				plla: pllack {
-					compatible = "atmel,at91rm9200-clk-pll";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_LOCKA>;
-					clocks = <&main>;
-					reg = <0>;
-					atmel,clk-input-range = <1000000 32000000>;
-					#atmel,pll-clk-output-range-cells = <3>;
-					atmel,pll-clk-output-ranges = <80000000 160000000 0>,
-								<150000000 180000000 2>;
-				};
-
-				pllb: pllbck {
-					compatible = "atmel,at91rm9200-clk-pll";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_LOCKB>;
-					clocks = <&main>;
-					reg = <1>;
-					atmel,clk-input-range = <1000000 32000000>;
-					#atmel,pll-clk-output-range-cells = <3>;
-					atmel,pll-clk-output-ranges = <80000000 160000000 0>,
-								<150000000 180000000 2>;
-				};
-
-				mck: masterck {
-					compatible = "atmel,at91rm9200-clk-master";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
-					clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
-					atmel,clk-output-range = <0 80000000>;
-					atmel,clk-divisors = <1 2 3 4>;
-				};
-
-				usb: usbck {
-					compatible = "atmel,at91rm9200-clk-usb";
-					#clock-cells = <0>;
-					atmel,clk-divisors = <1 2 0 0>;
-					clocks = <&pllb>;
-				};
-
-				prog: progck {
-					compatible = "atmel,at91rm9200-clk-programmable";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					interrupt-parent = <&pmc>;
-					clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
-
-					prog0: prog0 {
-						#clock-cells = <0>;
-						reg = <0>;
-						interrupts = <AT91_PMC_PCKRDY(0)>;
-					};
-
-					prog1: prog1 {
-						#clock-cells = <0>;
-						reg = <1>;
-						interrupts = <AT91_PMC_PCKRDY(1)>;
-					};
-
-					prog2: prog2 {
-						#clock-cells = <0>;
-						reg = <2>;
-						interrupts = <AT91_PMC_PCKRDY(2)>;
-					};
-
-					prog3: prog3 {
-						#clock-cells = <0>;
-						reg = <3>;
-						interrupts = <AT91_PMC_PCKRDY(3)>;
-					};
-				};
-
-				systemck {
-					compatible = "atmel,at91rm9200-clk-system";
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					udpck: udpck {
-						#clock-cells = <0>;
-						reg = <2>;
-						clocks = <&usb>;
-					};
-
-					uhpck: uhpck {
-						#clock-cells = <0>;
-						reg = <4>;
-						clocks = <&usb>;
-					};
-
-					pck0: pck0 {
-						#clock-cells = <0>;
-						reg = <8>;
-						clocks = <&prog0>;
-					};
-
-					pck1: pck1 {
-						#clock-cells = <0>;
-						reg = <9>;
-						clocks = <&prog1>;
-					};
-
-					pck2: pck2 {
-						#clock-cells = <0>;
-						reg = <10>;
-						clocks = <&prog2>;
-					};
-
-					pck3: pck3 {
-						#clock-cells = <0>;
-						reg = <11>;
-						clocks = <&prog3>;
-					};
-				};
-
-				periphck {
-					compatible = "atmel,at91rm9200-clk-peripheral";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&mck>;
-
-					pioA_clk: pioA_clk {
-						#clock-cells = <0>;
-						reg = <2>;
-					};
-
-					pioB_clk: pioB_clk {
-						#clock-cells = <0>;
-						reg = <3>;
-					};
-
-					pioC_clk: pioC_clk {
-						#clock-cells = <0>;
-						reg = <4>;
-					};
-
-					pioD_clk: pioD_clk {
-						#clock-cells = <0>;
-						reg = <5>;
-					};
-
-					usart0_clk: usart0_clk {
-						#clock-cells = <0>;
-						reg = <6>;
-					};
-
-					usart1_clk: usart1_clk {
-						#clock-cells = <0>;
-						reg = <7>;
-					};
-
-					usart2_clk: usart2_clk {
-						#clock-cells = <0>;
-						reg = <8>;
-					};
-
-					usart3_clk: usart3_clk {
-						#clock-cells = <0>;
-						reg = <9>;
-					};
-
-					mci0_clk: mci0_clk {
-						#clock-cells = <0>;
-						reg = <10>;
-					};
-
-					udc_clk: udc_clk {
-						#clock-cells = <0>;
-						reg = <11>;
-					};
-
-					twi0_clk: twi0_clk {
-						reg = <12>;
-						#clock-cells = <0>;
-					};
-
-					spi0_clk: spi0_clk {
-						#clock-cells = <0>;
-						reg = <13>;
-					};
-
-					ssc0_clk: ssc0_clk {
-						#clock-cells = <0>;
-						reg = <14>;
-					};
-
-					ssc1_clk: ssc1_clk {
-						#clock-cells = <0>;
-						reg = <15>;
-					};
-
-					ssc2_clk: ssc2_clk {
-						#clock-cells = <0>;
-						reg = <16>;
-					};
-
-					tc0_clk: tc0_clk {
-						#clock-cells = <0>;
-						reg = <17>;
-					};
-
-					tc1_clk: tc1_clk {
-						#clock-cells = <0>;
-						reg = <18>;
-					};
-
-					tc2_clk: tc2_clk {
-						#clock-cells = <0>;
-						reg = <19>;
-					};
-
-					tc3_clk: tc3_clk {
-						#clock-cells = <0>;
-						reg = <20>;
-					};
-
-					tc4_clk: tc4_clk {
-						#clock-cells = <0>;
-						reg = <21>;
-					};
-
-					tc5_clk: tc5_clk {
-						#clock-cells = <0>;
-						reg = <22>;
-					};
-
-					ohci_clk: ohci_clk {
-						#clock-cells = <0>;
-						reg = <23>;
-					};
-
-					macb0_clk: macb0_clk {
-						#clock-cells = <0>;
-						reg = <24>;
-					};
-				};
+				#clock-cells = <2>;
+				clocks = <&slow_xtal>, <&main_xtal>;
+				clock-names = "slow_xtal", "main_xtal";
 			};
 
 			st: timer@fffffd00 {
@@ -380,10 +135,10 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
-				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
-					      18 IRQ_TYPE_LEVEL_HIGH 0
-					      19 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>, <&slow_xtal>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <18 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <19 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 19>, <&slow_xtal>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
 
@@ -392,10 +147,10 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffa4000 0x100>;
-				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0
-					      21 IRQ_TYPE_LEVEL_HIGH 0
-					      22 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tc3_clk>, <&tc4_clk>, <&tc5_clk>, <&slow_xtal>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <21 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <22 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>, <&pmc PMC_TYPE_PERIPHERAL 21>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&slow_xtal>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
 
@@ -405,7 +160,7 @@
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_twi>;
-				clocks = <&twi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -415,11 +170,10 @@
 				compatible = "atmel,hsmci";
 				reg = <0xfffb4000 0x4000>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&mci0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
 				clock-names = "mci_clk";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				pinctrl-names = "default";
 				status = "disabled";
 			};
 
@@ -429,7 +183,7 @@
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
-				clocks = <&ssc0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -440,7 +194,7 @@
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
-				clocks = <&ssc1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -451,7 +205,7 @@
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>;
-				clocks = <&ssc2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -463,7 +217,7 @@
 				phy-mode = "rmii";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb_rmii>;
-				clocks = <&macb0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 24>;
 				clock-names = "ether_clk";
 				status = "disabled";
 			};
@@ -803,7 +557,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioA_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
 				};
 
 				pioB: gpio@fffff600 {
@@ -814,7 +568,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioB_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
 				};
 
 				pioC: gpio@fffff800 {
@@ -825,7 +579,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioC_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
 				};
 
 				pioD: gpio@fffffa00 {
@@ -836,17 +590,18 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioD_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
 				};
 			};
 
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -854,12 +609,13 @@
 			usart0: serial@fffc0000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
-				clocks = <&usart0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -867,12 +623,13 @@
 			usart1: serial@fffc4000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
-				clocks = <&usart1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -880,12 +637,13 @@
 			usart2: serial@fffc8000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart2>;
-				clocks = <&usart2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -893,12 +651,13 @@
 			usart3: serial@fffcc000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffcc000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart3>;
-				clocks = <&usart3_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -907,7 +666,7 @@
 				compatible = "atmel,at91rm9200-udc";
 				reg = <0xfffb0000 0x4000>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>;
-				clocks = <&udc_clk>, <&udpck>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>, <&pmc PMC_TYPE_SYSTEM 1>;
 				clock-names = "pclk", "hclk";
 				status = "disabled";
 			};
@@ -920,7 +679,7 @@
 				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0>;
-				clocks = <&spi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
@@ -947,7 +706,7 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00300000 0x100000>;
 			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&ohci_clk>, <&ohci_clk>, <&uhpck>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_SYSTEM 4>;
 			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/at91rm9200_pqfp.dtsi b/arch/arm/boot/dts/microchip/at91rm9200_pqfp.dtsi
index c3d4177b9823..c3d4177b9823 100644
--- a/arch/arm/boot/dts/at91rm9200_pqfp.dtsi
+++ b/arch/arm/boot/dts/microchip/at91rm9200_pqfp.dtsi
diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
index 1e0bf5afa913..4624a6f076f8 100644
--- a/arch/arm/boot/dts/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
@@ -15,7 +15,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -73,7 +73,7 @@
 			spi0: spi@fffe0000 {
 				status = "okay";
 				cs-gpios = <&pioA 3 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <15000000>;
 					reg = <0>;
@@ -94,7 +94,7 @@
 			status = "okay";
 		};
 
-		nor_flash@10000000 {
+		flash@10000000 {
 			compatible = "cfi-flash";
 			reg = <0x10000000 0x800000>;
 			linux,mtd-name = "physmap-flash.0";
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/microchip/at91sam9260.dtsi
index dee9c0c8a096..e56d5546554c 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9260.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -36,16 +37,17 @@
 		ssc0 = &ssc0;
 	};
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x04000000>;
 	};
@@ -63,7 +65,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <5000000>;
@@ -73,6 +75,9 @@
 	sram0: sram@2ff000 {
 		compatible = "mmio-sram";
 		reg = <0x002ff000 0x2000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x002ff000 0x2000>;
 	};
 
 	ahb {
@@ -110,7 +115,7 @@
 				reg = <0xffffee00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9260-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -119,13 +124,13 @@
 				clock-names = "slow_xtal", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>;
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>;
@@ -143,9 +148,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
-				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
-					      18 IRQ_TYPE_LEVEL_HIGH 0
-					      19 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <18 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <19 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 19>, <&pmc PMC_TYPE_CORE PMC_SLOW>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
@@ -155,14 +160,14 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffdc000 0x100>;
-				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0
-					      27 IRQ_TYPE_LEVEL_HIGH 0
-					      28 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <27 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <28 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_PERIPHERAL 28>, <&pmc PMC_TYPE_CORE PMC_SLOW>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
 
-			pinctrl@fffff400 {
+			pinctrl: pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
@@ -187,7 +192,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -221,7 +226,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -239,7 +244,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -257,7 +262,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -275,7 +280,7 @@
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_NONE
+							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
 					};
 				};
@@ -283,7 +288,7 @@
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 				};
@@ -528,6 +533,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -539,6 +545,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -552,6 +559,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -565,6 +573,7 @@
 			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -578,6 +587,7 @@
 			usart3: serial@fffd0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -591,6 +601,7 @@
 			uart0: serial@fffd4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -604,6 +615,7 @@
 			uart1: serial@fffd8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -650,7 +662,6 @@
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				pinctrl-names = "default";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				clock-names = "mci_clk";
 				status = "disabled";
@@ -694,8 +705,6 @@
 			};
 
 			adc0: adc@fffe0000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffe0000 0x100>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -705,29 +714,6 @@
 				atmel,adc-channels-used = <0xf>;
 				atmel,adc-vref = <3300>;
 				atmel,adc-startup-time = <15>;
-				atmel,adc-res = <8 10>;
-				atmel,adc-res-names = "lowres", "highres";
-				atmel,adc-use-res = "highres";
-
-				trigger0 {
-					trigger-name = "timer-counter-0";
-					trigger-value = <0x1>;
-				};
-				trigger1 {
-					trigger-name = "timer-counter-1";
-					trigger-value = <0x3>;
-				};
-
-				trigger2 {
-					trigger-name = "timer-counter-2";
-					trigger-value = <0x5>;
-				};
-
-				trigger3 {
-					trigger-name = "external";
-					trigger-value = <0xd>;
-					trigger-external;
-				};
 			};
 
 			rtc@fffffd20 {
@@ -738,7 +724,7 @@
 				status = "disabled";
 			};
 
-			watchdog@fffffd40 {
+			watchdog: watchdog@fffffd40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffd40 0x10>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -793,7 +779,7 @@
 		};
 	};
 
-	i2c-gpio-0 {
+	i2c_gpio0: i2c-gpio-0 {
 		compatible = "i2c-gpio";
 		gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
 			 &pioA 24 GPIO_ACTIVE_HIGH /* scl */
diff --git a/arch/arm/boot/dts/at91sam9260ek.dts b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
index 81f808a10931..720c15472c4a 100644
--- a/arch/arm/boot/dts/at91sam9260ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
@@ -7,6 +7,7 @@
  */
 /dts-v1/;
 #include "at91sam9260.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Atmel at91sam9260ek";
@@ -16,7 +17,7 @@
 		stdout-path = &dbgu;
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -55,6 +56,7 @@
 					&pinctrl_mmc0_clk
 					&pinctrl_mmc0_slot1_cmd_dat0
 					&pinctrl_mmc0_slot1_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@1 {
 					reg = <1>;
@@ -90,7 +92,7 @@
 
 			spi0: spi@fffc8000 {
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
-				mtd_dataflash@1 {
+				flash@1 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <1>;
@@ -110,7 +112,7 @@
 				};
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
@@ -142,20 +144,20 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn3 {
+		button-3 {
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		btn4 {
+		button-4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
-			linux,code = <0x104>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/microchip/at91sam9261.dtsi
index dba025a98527..307b60658014 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9261.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -33,16 +34,17 @@
 	};
 
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x08000000>;
 	};
@@ -64,6 +66,9 @@
 	sram: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x28000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x28000>;
 	};
 
 	ahb {
@@ -175,6 +180,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -188,6 +194,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -198,9 +205,10 @@
 				status = "disabled";
 			};
 
-			usart2: serial@fffb8000{
+			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -297,6 +305,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -329,7 +338,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -347,7 +356,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -365,7 +374,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -590,7 +599,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9261-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -599,13 +608,13 @@
 				clock-names = "slow_xtal", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&slow_xtal>;
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&slow_xtal>;
diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
index c4ef74fea97c..045cb253f23a 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
@@ -16,7 +16,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -145,7 +145,7 @@
 				cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>;
 				status = "okay";
 
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					reg = <0>;
 					spi-max-frequency = <15000000>;
@@ -156,7 +156,7 @@
 					compatible = "ti,ads7843";
 					interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>;
 					spi-max-frequency = <3000000>;
-					pendown-gpio = <&pioC 2 GPIO_ACTIVE_HIGH>;
+					pendown-gpio = <&pioC 2 GPIO_ACTIVE_LOW>;
 
 					ti,x-min = /bits/ 16 <150>;
 					ti,x-max = /bits/ 16 <3830>;
@@ -178,6 +178,10 @@
 				status = "okay";
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			watchdog@fffffd40 {
 				status = "okay";
 			};
@@ -207,31 +211,31 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		button_0 {
+		button-0 {
 			label = "button_0";
 			gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
 			linux,code = <256>;
 			wakeup-source;
 		};
 
-		button_1 {
+		button-1 {
 			label = "button_1";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			linux,code = <257>;
 			wakeup-source;
 		};
 
-		button_2 {
+		button-2 {
 			label = "button_2";
 			gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
 			linux,code = <258>;
 			wakeup-source;
 		};
 
-		button_3 {
+		button-3 {
 			label = "button_3";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <259>;
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/microchip/at91sam9263.dtsi
index 99678abdda93..75d8ff2d12c8 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9263.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -35,16 +36,17 @@
 	};
 
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x08000000>;
 	};
@@ -66,11 +68,17 @@
 	sram0: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x14000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x14000>;
 	};
 
 	sram1: sram@500000 {
 		compatible = "mmio-sram";
 		reg = <0x00500000 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00500000 0x4000>;
 	};
 
 	ahb {
@@ -93,7 +101,7 @@
 				atmel,external-irqs = <30 31>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9263-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -144,13 +152,13 @@
 				clock-names = "t0_clk", "slow_clk";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&slow_xtal>;
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&slow_xtal>;
@@ -183,7 +191,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -201,7 +209,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -219,7 +227,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -533,6 +541,7 @@
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -544,6 +553,7 @@
 			usart0: serial@fff8c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff8c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -557,6 +567,7 @@
 			usart1: serial@fff90000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff90000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -570,6 +581,7 @@
 			usart2: serial@fff94000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff94000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -647,7 +659,6 @@
 				compatible = "atmel,hsmci";
 				reg = <0xfff80000 0x600>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
-				pinctrl-names = "default";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
@@ -659,7 +670,6 @@
 				compatible = "atmel,hsmci";
 				reg = <0xfff84000 0x600>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
-				pinctrl-names = "default";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
index 62d218542a48..ce8baff6a9f4 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
@@ -16,7 +16,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -72,6 +72,7 @@
 					&pinctrl_mmc0_clk
 					&pinctrl_mmc0_slot0_cmd_dat0
 					&pinctrl_mmc0_slot0_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@0 {
 					reg = <0>;
@@ -94,13 +95,17 @@
 			spi0: spi@fffa4000 {
 				status = "okay";
 				cs-gpios = <&pioA 5 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
 				};
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			watchdog@fffffd40 {
 				status = "okay";
 			};
@@ -227,17 +232,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			wakeup-source;
 		};
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
diff --git a/arch/arm/boot/dts/at91sam9g15.dtsi b/arch/arm/boot/dts/microchip/at91sam9g15.dtsi
index dde88276fe52..dde88276fe52 100644
--- a/arch/arm/boot/dts/at91sam9g15.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g15.dtsi
diff --git a/arch/arm/boot/dts/at91sam9g15ek.dts b/arch/arm/boot/dts/microchip/at91sam9g15ek.dts
index 889a5097eb2d..889a5097eb2d 100644
--- a/arch/arm/boot/dts/at91sam9g15ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g15ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/microchip/at91sam9g20.dtsi
index 4117cf880508..738a43ffd228 100644
--- a/arch/arm/boot/dts/at91sam9g20.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g20.dtsi
@@ -11,7 +11,7 @@
 	model = "Atmel AT91SAM9G20 family SoC";
 	compatible = "atmel,at91sam9g20";
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x08000000>;
 	};
 
@@ -22,6 +22,9 @@
 	sram1: sram@2fc000 {
 		compatible = "mmio-sram";
 		reg = <0x002fc000 0x8000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x002fc000 0x8000>;
 	};
 
 	ahb {
@@ -38,7 +41,7 @@
 				atmel,adc-startup-time = <40>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g20-pmc", "atmel,at91sam9260-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9g20ek.dts b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
index 6de7a7cd3c07..6de7a7cd3c07 100644
--- a/arch/arm/boot/dts/at91sam9g20ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts b/arch/arm/boot/dts/microchip/at91sam9g20ek_2mmc.dts
index 2db95e8ffc64..172af6ff4b18 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek_2mmc.dts
@@ -12,7 +12,7 @@
 	compatible = "atmel,at91sam9g20ek_2mmc", "atmel,at91sam9g20", "atmel,at91sam9";
 
 	ahb {
-		apb{
+		apb {
 			mmc0: mmc@fffa8000 {
 				/* clk already mux wuth slot0 */
 				pinctrl-0 = <
diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/microchip/at91sam9g20ek_common.dtsi
index bda22700110c..565b99e79c52 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek_common.dtsi
@@ -5,6 +5,7 @@
  * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
 #include "at91sam9g20.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 
@@ -13,7 +14,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -38,6 +39,13 @@
 
 				};
 
+				usb1 {
+					pinctrl_usb1_vbus_gpio: usb1_vbus_gpio {
+						atmel,pins =
+							<AT91_PIOC 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PC5 GPIO */
+					};
+				};
+
 				mmc0_slot1 {
 					pinctrl_board_mmc0_slot1: mmc0_slot1-board {
 						atmel,pins =
@@ -83,6 +91,8 @@
 			};
 
 			usb1: gadget@fffa4000 {
+				pinctrl-0 = <&pinctrl_usb1_vbus_gpio>;
+				pinctrl-names = "default";
 				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
@@ -93,6 +103,7 @@
 					&pinctrl_mmc0_clk
 					&pinctrl_mmc0_slot1_cmd_dat0
 					&pinctrl_mmc0_slot1_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@1 {
 					reg = <1>;
@@ -108,14 +119,14 @@
 
 			spi0: spi@fffc8000 {
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
-				mtd_dataflash@1 {
+				flash@1 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <1>;
 				};
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
@@ -212,28 +223,40 @@
 		24c512@50 {
 			compatible = "atmel,24c512";
 			reg = <0x50>;
+			vcc-supply = <&reg_3v3>;
 		};
 
 		wm8731: wm8731@1b {
 			compatible = "wm8731";
 			reg = <0x1b>;
+
+			/* PCK0 at 12MHz */
+			clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			clock-names = "mclk";
+			assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			assigned-clock-rates = <12000000>;
+
+			HPVDD-supply = <&vcc_dac>;
+			AVDD-supply = <&vcc_dac>;
+			DCVDD-supply = <&reg_3v3>;
+			DBVDD-supply = <&reg_3v3>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn3 {
+		button-3 {
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		btn4 {
+		button-4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
-			linux,code = <0x104>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
@@ -252,4 +275,35 @@
 		atmel,ssc-controller = <&ssc0>;
 		atmel,audio-codec = <&wm8731>;
 	};
+
+	reg_5v: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_3v3: fixedregulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		vin-supply = <&reg_5v>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_1v: fixedregulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V";
+		vin-supply = <&reg_5v>;
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+	vcc_dac: fixedregulator3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_DAC";
+		vin-supply = <&reg_3v3>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
diff --git a/arch/arm/boot/dts/microchip/at91sam9g25-gardena-smart-gateway.dts b/arch/arm/boot/dts/microchip/at91sam9g25-gardena-smart-gateway.dts
new file mode 100644
index 000000000000..92f2c05c873f
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91sam9g25-gardena-smart-gateway.dts
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for the GARDENA smart Gateway (Article No. 19000)
+ *
+ *  Copyright (C) 2020 GARDENA GmbH
+ */
+
+/dts-v1/;
+
+#include "at91sam9g25.dtsi"
+#include "at91sam9x5ek.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "GARDENA smart Gateway (Article No. 19000)";
+	compatible = "gardena,smart-gateway-at91sam", "atmel,at91sam9g25", "atmel,at91sam9x5",
+		"atmel,at91sam9";
+
+	aliases {
+		serial1 = &usart3;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button {
+			label = "USER_BTN1";
+			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+		};
+	};
+
+	1wire_cm {
+		status = "disabled";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power_blue {
+			label = "smartgw:power:blue";
+			gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		power_green {
+			label = "smartgw:power:green";
+			gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		power_red {
+			label = "smartgw:power:red";
+			gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		radio_blue {
+			label = "smartgw:radio:blue";
+			gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		radio_green {
+			label = "smartgw:radio:green";
+			gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		radio_red {
+			label = "smartgw:radio:red";
+			gpios = <&pioC 16 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		internet_blue {
+			label = "smartgw:internet:blue";
+			gpios = <&pioC 15 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		internet_green {
+			label = "smartgw:internet:green";
+			gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		internet_red {
+			label = "smartgw:internet:red";
+			gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		heartbeat {
+			label = "smartgw:heartbeat";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		pb18 {
+			status = "disabled";
+		};
+
+		pd21 {
+			status = "disabled";
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&usart0 {
+	status = "disabled";
+};
+
+&usart2 {
+	status = "disabled";
+};
+
+&usart3 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_usart3
+		     &pinctrl_usart3_rts
+		     &pinctrl_usart3_cts
+		    >;
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&mmc0 {
+	status = "disabled";
+};
+
+&mmc1 {
+	status = "disabled";
+};
+
+&spi0 {
+	status = "disabled";
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&adc0 {
+	status = "disabled";
+};
+
+&ssc0 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/at91sam9g25.dtsi b/arch/arm/boot/dts/microchip/at91sam9g25.dtsi
index d2f13afb35ea..ec3c77221881 100644
--- a/arch/arm/boot/dts/at91sam9g25.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g25.dtsi
@@ -26,7 +26,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g25-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/microchip/at91sam9g25ek.dts
index 61b0bdb615dc..61b0bdb615dc 100644
--- a/arch/arm/boot/dts/at91sam9g25ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g25ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g35.dtsi b/arch/arm/boot/dts/microchip/at91sam9g35.dtsi
index 48c2bc4a7753..c9cfb93092ee 100644
--- a/arch/arm/boot/dts/at91sam9g35.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g35.dtsi
@@ -25,7 +25,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g35-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9g35ek.dts b/arch/arm/boot/dts/microchip/at91sam9g35ek.dts
index f966b56de63c..f966b56de63c 100644
--- a/arch/arm/boot/dts/at91sam9g35ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g35ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/microchip/at91sam9g45.dtsi
index 691c95ea6175..325c63a53118 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g45.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -41,16 +42,17 @@
 		pwm0 = &pwm0;
 	};
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@70000000 {
 		device_type = "memory";
 		reg = <0x70000000 0x10000000>;
 	};
@@ -68,7 +70,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <300000>;
@@ -78,6 +80,9 @@
 	sram: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x10000>;
 	};
 
 	ahb {
@@ -103,14 +108,14 @@
 			ramc0: ramc@ffffe400 {
 				compatible = "atmel,at91sam9g45-ddramc";
 				reg = <0xffffe400 0x200>;
-				clocks = <&ddrck>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>;
 				clock-names = "ddrck";
 			};
 
 			ramc1: ramc@ffffe600 {
 				compatible = "atmel,at91sam9g45-ddramc";
 				reg = <0xffffe600 0x200>;
-				clocks = <&ddrck>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>;
 				clock-names = "ddrck";
 			};
 
@@ -124,278 +129,16 @@
 				reg = <0xffffea00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g45-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				#interrupt-cells = <1>;
-
-				main_osc: main_osc {
-					compatible = "atmel,at91rm9200-clk-main-osc";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clocks = <&main_xtal>;
-				};
-
-				main: mainck {
-					compatible = "atmel,at91rm9200-clk-main";
-					#clock-cells = <0>;
-					clocks = <&main_osc>;
-				};
-
-				plla: pllack {
-					compatible = "atmel,at91rm9200-clk-pll";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_LOCKA>;
-					clocks = <&main>;
-					reg = <0>;
-					atmel,clk-input-range = <2000000 32000000>;
-					#atmel,pll-clk-output-range-cells = <4>;
-					atmel,pll-clk-output-ranges = <745000000 800000000 0 0
-								       695000000 750000000 1 0
-								       645000000 700000000 2 0
-								       595000000 650000000 3 0
-								       545000000 600000000 0 1
-								       495000000 555000000 1 1
-								       445000000 500000000 2 1
-								       400000000 450000000 3 1>;
-				};
-
-				plladiv: plladivck {
-					compatible = "atmel,at91sam9x5-clk-plldiv";
-					#clock-cells = <0>;
-					clocks = <&plla>;
-				};
-
-				utmi: utmick {
-					compatible = "atmel,at91sam9x5-clk-utmi";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_LOCKU>;
-					clocks = <&main>;
-				};
-
-				mck: masterck {
-					compatible = "atmel,at91rm9200-clk-master";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
-					clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
-					atmel,clk-output-range = <0 133333333>;
-					atmel,clk-divisors = <1 2 4 3>;
-				};
-
-				usb: usbck {
-					compatible = "atmel,at91sam9x5-clk-usb";
-					#clock-cells = <0>;
-					clocks = <&plladiv>, <&utmi>;
-				};
-
-				prog: progck {
-					compatible = "atmel,at91sam9g45-clk-programmable";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					interrupt-parent = <&pmc>;
-					clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
-
-					prog0: prog0 {
-						#clock-cells = <0>;
-						reg = <0>;
-						interrupts = <AT91_PMC_PCKRDY(0)>;
-					};
-
-					prog1: prog1 {
-						#clock-cells = <0>;
-						reg = <1>;
-						interrupts = <AT91_PMC_PCKRDY(1)>;
-					};
-				};
-
-				systemck {
-					compatible = "atmel,at91rm9200-clk-system";
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					ddrck: ddrck {
-						#clock-cells = <0>;
-						reg = <2>;
-						clocks = <&mck>;
-					};
-
-					uhpck: uhpck {
-						#clock-cells = <0>;
-						reg = <6>;
-						clocks = <&usb>;
-					};
-
-					pck0: pck0 {
-						#clock-cells = <0>;
-						reg = <8>;
-						clocks = <&prog0>;
-					};
-
-					pck1: pck1 {
-						#clock-cells = <0>;
-						reg = <9>;
-						clocks = <&prog1>;
-					};
-				};
-
-				periphck {
-					compatible = "atmel,at91rm9200-clk-peripheral";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&mck>;
-
-					pioA_clk: pioA_clk {
-						#clock-cells = <0>;
-						reg = <2>;
-					};
-
-					pioB_clk: pioB_clk {
-						#clock-cells = <0>;
-						reg = <3>;
-					};
-
-					pioC_clk: pioC_clk {
-						#clock-cells = <0>;
-						reg = <4>;
-					};
-
-					pioDE_clk: pioDE_clk {
-						#clock-cells = <0>;
-						reg = <5>;
-					};
-
-					trng_clk: trng_clk {
-						#clock-cells = <0>;
-						reg = <6>;
-					};
-
-					usart0_clk: usart0_clk {
-						#clock-cells = <0>;
-						reg = <7>;
-					};
-
-					usart1_clk: usart1_clk {
-						#clock-cells = <0>;
-						reg = <8>;
-					};
-
-					usart2_clk: usart2_clk {
-						#clock-cells = <0>;
-						reg = <9>;
-					};
-
-					usart3_clk: usart3_clk {
-						#clock-cells = <0>;
-						reg = <10>;
-					};
-
-					mci0_clk: mci0_clk {
-						#clock-cells = <0>;
-						reg = <11>;
-					};
-
-					twi0_clk: twi0_clk {
-						#clock-cells = <0>;
-						reg = <12>;
-					};
-
-					twi1_clk: twi1_clk {
-						#clock-cells = <0>;
-						reg = <13>;
-					};
-
-					spi0_clk: spi0_clk {
-						#clock-cells = <0>;
-						reg = <14>;
-					};
-
-					spi1_clk: spi1_clk {
-						#clock-cells = <0>;
-						reg = <15>;
-					};
-
-					ssc0_clk: ssc0_clk {
-						#clock-cells = <0>;
-						reg = <16>;
-					};
-
-					ssc1_clk: ssc1_clk {
-						#clock-cells = <0>;
-						reg = <17>;
-					};
-
-					tcb0_clk: tcb0_clk {
-						#clock-cells = <0>;
-						reg = <18>;
-					};
-
-					pwm_clk: pwm_clk {
-						#clock-cells = <0>;
-						reg = <19>;
-					};
-
-					adc_clk: adc_clk {
-						#clock-cells = <0>;
-						reg = <20>;
-					};
-
-					dma0_clk: dma0_clk {
-						#clock-cells = <0>;
-						reg = <21>;
-					};
-
-					uhphs_clk: uhphs_clk {
-						#clock-cells = <0>;
-						reg = <22>;
-					};
-
-					lcd_clk: lcd_clk {
-						#clock-cells = <0>;
-						reg = <23>;
-					};
-
-					ac97_clk: ac97_clk {
-						#clock-cells = <0>;
-						reg = <24>;
-					};
-
-					macb0_clk: macb0_clk {
-						#clock-cells = <0>;
-						reg = <25>;
-					};
-
-					isi_clk: isi_clk {
-						#clock-cells = <0>;
-						reg = <26>;
-					};
-
-					udphs_clk: udphs_clk {
-						#clock-cells = <0>;
-						reg = <27>;
-					};
-
-					aestdessha_clk: aestdessha_clk {
-						#clock-cells = <0>;
-						reg = <28>;
-					};
-
-					mci1_clk: mci1_clk {
-						#clock-cells = <0>;
-						reg = <29>;
-					};
-
-					vdec_clk: vdec_clk {
-						#clock-cells = <0>;
-						reg = <30>;
-					};
-				};
+				#clock-cells = <2>;
+				clocks = <&clk32k>, <&main_xtal>;
+				clock-names = "slow_clk", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&clk32k>;
@@ -405,11 +148,11 @@
 				compatible = "atmel,at91sam9260-pit";
 				reg = <0xfffffd30 0xf>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			};
 
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9rl-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&clk32k>;
@@ -421,7 +164,7 @@
 				#size-cells = <0>;
 				reg = <0xfff7c000 0x100>;
 				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tcb0_clk>, <&tcb0_clk>, <&tcb0_clk>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&clk32k>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
 
@@ -431,7 +174,7 @@
 				#size-cells = <0>;
 				reg = <0xfffd4000 0x100>;
 				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tcb0_clk>, <&tcb0_clk>, <&tcb0_clk>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&clk32k>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
 
@@ -440,7 +183,7 @@
 				reg = <0xffffec00 0x200>;
 				interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
 				#dma-cells = <2>;
-				clocks = <&dma0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
 				clock-names = "dma_clk";
 			};
 
@@ -556,7 +299,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -574,7 +317,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -592,7 +335,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -610,7 +353,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -883,7 +626,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioA_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
 				};
 
 				pioB: gpio@fffff400 {
@@ -894,7 +637,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioB_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
 				};
 
 				pioC: gpio@fffff600 {
@@ -905,7 +648,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioC_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
 				};
 
 				pioD: gpio@fffff800 {
@@ -916,7 +659,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioDE_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
 				};
 
 				pioE: gpio@fffffa00 {
@@ -927,17 +670,18 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioDE_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
 				};
 			};
 
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				reg = <0xffffee00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -945,12 +689,13 @@
 			usart0: serial@fff8c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff8c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
-				clocks = <&usart0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -958,12 +703,13 @@
 			usart1: serial@fff90000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff90000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
-				clocks = <&usart1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -971,12 +717,13 @@
 			usart2: serial@fff94000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff94000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
-				clocks = <&usart2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -984,12 +731,13 @@
 			usart3: serial@fff98000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff98000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
-				clocks = <&usart3_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -1000,7 +748,7 @@
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb_rmii>;
-				clocks = <&macb0_clk>, <&macb0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 25>, <&pmc PMC_TYPE_PERIPHERAL 25>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
 			};
@@ -1009,7 +757,7 @@
 				compatible = "atmel,at91sam9g45-trng";
 				reg = <0xfffcc000 0x100>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&trng_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
 			};
 
 			i2c0: i2c@fff84000 {
@@ -1020,7 +768,7 @@
 				pinctrl-0 = <&pinctrl_i2c0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&twi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				status = "disabled";
 			};
 
@@ -1032,7 +780,7 @@
 				pinctrl-0 = <&pinctrl_i2c1>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&twi1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
 				status = "disabled";
 			};
 
@@ -1042,7 +790,7 @@
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
-				clocks = <&ssc0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -1053,7 +801,7 @@
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
-				clocks = <&ssc1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -1064,54 +812,27 @@
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 4>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ac97>;
-				clocks = <&ac97_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 24>;
 				clock-names = "ac97_clk";
 				status = "disabled";
 			};
 
 			adc0: adc@fffb0000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9g45-adc";
 				reg = <0xfffb0000 0x100>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&adc_clk>, <&adc_op_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>, <&adc_op_clk>;
 				clock-names = "adc_clk", "adc_op_clk";
 				atmel,adc-channels-used = <0xff>;
 				atmel,adc-vref = <3300>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-res = <8 10>;
-				atmel,adc-res-names = "lowres", "highres";
-				atmel,adc-use-res = "highres";
-
-				trigger0 {
-					trigger-name = "external-rising";
-					trigger-value = <0x1>;
-					trigger-external;
-				};
-				trigger1 {
-					trigger-name = "external-falling";
-					trigger-value = <0x2>;
-					trigger-external;
-				};
-
-				trigger2 {
-					trigger-name = "external-any";
-					trigger-value = <0x3>;
-					trigger-external;
-				};
-
-				trigger3 {
-					trigger-name = "continuous";
-					trigger-value = <0x6>;
-				};
 			};
 
 			isi@fffb4000 {
 				compatible = "atmel,at91sam9g45-isi";
 				reg = <0xfffb4000 0x4000>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 5>;
-				clocks = <&isi_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 26>;
 				clock-names = "isi_clk";
 				status = "disabled";
 				port {
@@ -1125,7 +846,7 @@
 				reg = <0xfffb8000 0x300>;
 				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>;
 				#pwm-cells = <3>;
-				clocks = <&pwm_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
 				status = "disabled";
 			};
 
@@ -1133,12 +854,11 @@
 				compatible = "atmel,hsmci";
 				reg = <0xfff80000 0x600>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
-				pinctrl-names = "default";
 				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>;
 				dma-names = "rxtx";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&mci0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
 				clock-names = "mci_clk";
 				status = "disabled";
 			};
@@ -1147,12 +867,11 @@
 				compatible = "atmel,hsmci";
 				reg = <0xfffd0000 0x600>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0>;
-				pinctrl-names = "default";
 				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(13)>;
 				dma-names = "rxtx";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&mci1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 29>;
 				clock-names = "mci_clk";
 				status = "disabled";
 			};
@@ -1176,7 +895,7 @@
 				interrupts = <14 4 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0>;
-				clocks = <&spi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
@@ -1189,76 +908,22 @@
 				interrupts = <15 4 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi1>;
-				clocks = <&spi1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
 
 			usb2: gadget@fff78000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9g45-udc";
 				reg = <0x00600000 0x80000
 				       0xfff78000 0x400>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&udphs_clk>, <&utmi>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
 				clock-names = "pclk", "hclk";
 				status = "disabled";
-
-				ep@0 {
-					reg = <0>;
-					atmel,fifo-size = <64>;
-					atmel,nb-banks = <1>;
-				};
-
-				ep@1 {
-					reg = <1>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <2>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@2 {
-					reg = <2>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <2>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@3 {
-					reg = <3>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-				};
-
-				ep@4 {
-					reg = <4>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-				};
-
-				ep@5 {
-					reg = <5>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@6 {
-					reg = <6>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
 			};
 
-			clk32k: sckc@fffffd50 {
+			clk32k: clock-controller@fffffd50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffd50 0x4>;
 				clocks = <&slow_xtal>;
@@ -1294,7 +959,7 @@
 			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_fb>;
-			clocks = <&lcd_clk>, <&lcd_clk>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_PERIPHERAL 23>;
 			clock-names = "hclk", "lcdc_clk";
 			status = "disabled";
 		};
@@ -1303,7 +968,7 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
 			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
@@ -1312,7 +977,7 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00800000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&utmi>, <&uhphs_clk>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
 			clock-names = "usb_clk", "ehci_clk";
 			status = "disabled";
 		};
@@ -1330,7 +995,7 @@
 				  0x3 0x0 0x40000000 0x10000000
 				  0x4 0x0 0x50000000 0x10000000
 				  0x5 0x0 0x60000000 0x10000000>;
-			clocks = <&mck>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			status = "disabled";
 
 			nand_controller: nand-controller {
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/microchip/at91sam9m10g45ek.dts
index 84bed6f55fcd..071db4f16313 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9m10g45ek.dts
@@ -18,7 +18,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@70000000 {
 		reg = <0x70000000 0x4000000>;
 	};
 
@@ -72,9 +72,9 @@
 					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
 					resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
 					pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
-					clocks = <&pck1>;
+					clocks = <&pmc PMC_TYPE_SYSTEM 9>;
 					clock-names = "xvclk";
-					assigned-clocks = <&pck1>;
+					assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
 					assigned-clock-rates = <25000000>;
 
 					port {
@@ -99,6 +99,7 @@
 					&pinctrl_board_mmc0
 					&pinctrl_mmc0_slot0_clk_cmd_dat0
 					&pinctrl_mmc0_slot0_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@0 {
 					reg = <0>;
@@ -112,6 +113,7 @@
 					&pinctrl_board_mmc1
 					&pinctrl_mmc1_slot0_clk_cmd_dat0
 					&pinctrl_mmc1_slot0_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@0 {
 					reg = <0>;
@@ -162,10 +164,10 @@
 				};
 			};
 
-			spi0: spi@fffa4000{
+			spi0: spi@fffa4000 {
 				status = "okay";
 				cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <13000000>;
 					reg = <0>;
@@ -313,27 +315,27 @@
 		};
 	};
 
-	leds {
+	led-controller-1 {
 		compatible = "gpio-leds";
 
-		d8 {
+		led-1 {
 			label = "d8";
 			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	pwmleds {
+	led-controller-2 {
 		compatible = "pwm-leds";
 
-		d6 {
+		led-2 {
 			label = "d6";
 			pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 			linux,default-trigger = "nand-disk";
 		};
 
-		d7 {
+		led-3 {
 			label = "d7";
 			pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
@@ -341,48 +343,48 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			wakeup-source;
 		};
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			wakeup-source;
 		};
 
-		left {
+		button-left {
 			label = "Joystick Left";
 			gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
 			linux,code = <105>;
 		};
 
-		right {
+		button-right {
 			label = "Joystick Right";
 			gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
 			linux,code = <106>;
 		};
 
-		up {
+		button-up {
 			label = "Joystick Up";
 			gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
 			linux,code = <103>;
 		};
 
-		down {
+		button-down {
 			label = "Joystick Down";
 			gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
 			linux,code = <108>;
 		};
 
-		enter {
+		button-enter {
 			label = "Joystick Press";
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/microchip/at91sam9n12.dtsi
index ea675174432e..8dc04e9031a6 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9n12.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -37,16 +38,17 @@
 		pwm0 = &pwm0;
 	};
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x10000000>;
 	};
@@ -68,6 +70,9 @@
 	sram: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x8000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x8000>;
 	};
 
 	ahb {
@@ -104,7 +109,7 @@
 			ramc0: ramc@ffffe800 {
 				compatible = "atmel,at91sam9g45-ddramc";
 				reg = <0xffffe800 0x200>;
-				clocks = <&ddrck>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>;
 				clock-names = "ddrck";
 			};
 
@@ -113,284 +118,16 @@
 				reg = <0xffffea00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9n12-pmc", "syscon";
 				reg = <0xfffffc00 0x200>;
+				#clock-cells = <2>;
+				clocks = <&clk32k>, <&main_xtal>;
+				clock-names = "slow_clk", "main_xtal";
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				#interrupt-cells = <1>;
-
-				main_rc_osc: main_rc_osc {
-					compatible = "atmel,at91sam9x5-clk-main-rc-osc";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCRCS>;
-					clock-frequency = <12000000>;
-					clock-accuracy = <50000000>;
-				};
-
-				main_osc: main_osc {
-					compatible = "atmel,at91rm9200-clk-main-osc";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clocks = <&main_xtal>;
-				};
-
-				main: mainck {
-					compatible = "atmel,at91sam9x5-clk-main";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MOSCSELS>;
-					clocks = <&main_rc_osc>, <&main_osc>;
-				};
-
-				plla: pllack {
-					compatible = "atmel,at91rm9200-clk-pll";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_LOCKA>;
-					clocks = <&main>;
-					reg = <0>;
-					atmel,clk-input-range = <2000000 32000000>;
-					#atmel,pll-clk-output-range-cells = <4>;
-					atmel,pll-clk-output-ranges = <745000000 800000000 0 0>,
-								      <695000000 750000000 1 0>,
-								      <645000000 700000000 2 0>,
-								      <595000000 650000000 3 0>,
-								      <545000000 600000000 0 1>,
-								      <495000000 555000000 1 1>,
-								      <445000000 500000000 2 1>,
-								      <400000000 450000000 3 1>;
-				};
-
-				plladiv: plladivck {
-					compatible = "atmel,at91sam9x5-clk-plldiv";
-					#clock-cells = <0>;
-					clocks = <&plla>;
-				};
-
-				pllb: pllbck {
-					compatible = "atmel,at91rm9200-clk-pll";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_LOCKB>;
-					clocks = <&main>;
-					reg = <1>;
-					atmel,clk-input-range = <2000000 32000000>;
-					#atmel,pll-clk-output-range-cells = <3>;
-					atmel,pll-clk-output-ranges = <30000000 100000000 0>;
-				};
-
-				mck: masterck {
-					compatible = "atmel,at91sam9x5-clk-master";
-					#clock-cells = <0>;
-					interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
-					clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>;
-					atmel,clk-output-range = <0 133333333>;
-					atmel,clk-divisors = <1 2 4 3>;
-					atmel,master-clk-have-div3-pres;
-				};
-
-				usb: usbck {
-					compatible = "atmel,at91sam9n12-clk-usb";
-					#clock-cells = <0>;
-					clocks = <&pllb>;
-				};
-
-				prog: progck {
-					compatible = "atmel,at91sam9x5-clk-programmable";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					interrupt-parent = <&pmc>;
-					clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>, <&mck>;
-
-					prog0: prog0 {
-						#clock-cells = <0>;
-						reg = <0>;
-						interrupts = <AT91_PMC_PCKRDY(0)>;
-					};
-
-					prog1: prog1 {
-						#clock-cells = <0>;
-						reg = <1>;
-						interrupts = <AT91_PMC_PCKRDY(1)>;
-					};
-				};
-
-				systemck {
-					compatible = "atmel,at91rm9200-clk-system";
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					ddrck: ddrck {
-						#clock-cells = <0>;
-						reg = <2>;
-						clocks = <&mck>;
-					};
-
-					lcdck: lcdck {
-						#clock-cells = <0>;
-						reg = <3>;
-						clocks = <&mck>;
-					};
-
-					uhpck: uhpck {
-						#clock-cells = <0>;
-						reg = <6>;
-						clocks = <&usb>;
-					};
-
-					udpck: udpck {
-						#clock-cells = <0>;
-						reg = <7>;
-						clocks = <&usb>;
-					};
-
-					pck0: pck0 {
-						#clock-cells = <0>;
-						reg = <8>;
-						clocks = <&prog0>;
-					};
-
-					pck1: pck1 {
-						#clock-cells = <0>;
-						reg = <9>;
-						clocks = <&prog1>;
-					};
-				};
-
-				periphck {
-					compatible = "atmel,at91sam9x5-clk-peripheral";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&mck>;
-
-					pioAB_clk: pioAB_clk {
-						#clock-cells = <0>;
-						reg = <2>;
-					};
-
-					pioCD_clk: pioCD_clk {
-						#clock-cells = <0>;
-						reg = <3>;
-					};
-
-					fuse_clk: fuse_clk {
-						#clock-cells = <0>;
-						reg = <4>;
-					};
-
-					usart0_clk: usart0_clk {
-						#clock-cells = <0>;
-						reg = <5>;
-					};
-
-					usart1_clk: usart1_clk {
-						#clock-cells = <0>;
-						reg = <6>;
-					};
-
-					usart2_clk: usart2_clk {
-						#clock-cells = <0>;
-						reg = <7>;
-					};
-
-					usart3_clk: usart3_clk {
-						#clock-cells = <0>;
-						reg = <8>;
-					};
-
-					twi0_clk: twi0_clk {
-						reg = <9>;
-						#clock-cells = <0>;
-					};
-
-					twi1_clk: twi1_clk {
-						#clock-cells = <0>;
-						reg = <10>;
-					};
-
-					mci0_clk: mci0_clk {
-						#clock-cells = <0>;
-						reg = <12>;
-					};
-
-					spi0_clk: spi0_clk {
-						#clock-cells = <0>;
-						reg = <13>;
-					};
-
-					spi1_clk: spi1_clk {
-						#clock-cells = <0>;
-						reg = <14>;
-					};
-
-					uart0_clk: uart0_clk {
-						#clock-cells = <0>;
-						reg = <15>;
-					};
-
-					uart1_clk: uart1_clk {
-						#clock-cells = <0>;
-						reg = <16>;
-					};
-
-					tcb_clk: tcb_clk {
-						#clock-cells = <0>;
-						reg = <17>;
-					};
-
-					pwm_clk: pwm_clk {
-						#clock-cells = <0>;
-						reg = <18>;
-					};
-
-					adc_clk: adc_clk {
-						#clock-cells = <0>;
-						reg = <19>;
-					};
-
-					dma0_clk: dma0_clk {
-						#clock-cells = <0>;
-						reg = <20>;
-					};
-
-					uhphs_clk: uhphs_clk {
-						#clock-cells = <0>;
-						reg = <22>;
-					};
-
-					udphs_clk: udphs_clk {
-						#clock-cells = <0>;
-						reg = <23>;
-					};
-
-					lcdc_clk: lcdc_clk {
-						#clock-cells = <0>;
-						reg = <25>;
-					};
-
-					sha_clk: sha_clk {
-						#clock-cells = <0>;
-						reg = <27>;
-					};
-
-					ssc0_clk: ssc0_clk {
-						#clock-cells = <0>;
-						reg = <28>;
-					};
-
-					aes_clk: aes_clk {
-						#clock-cells = <0>;
-						reg = <29>;
-					};
-
-					trng_clk: trng_clk {
-						#clock-cells = <0>;
-						reg = <30>;
-					};
-				};
 			};
 
-			rstc@fffffe00 {
+			reset-controller@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
@@ -400,37 +137,20 @@
 				compatible = "atmel,at91sam9260-pit";
 				reg = <0xfffffe30 0xf>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			};
 
-			shdwc@fffffe10 {
+			poweroff@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			sckc@fffffe50 {
+			clk32k: clock-controller@fffffe50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffe50 0x4>;
-
-				slow_osc: slow_osc {
-					compatible = "atmel,at91sam9x5-clk-slow-osc";
-					#clock-cells = <0>;
-					clocks = <&slow_xtal>;
-				};
-
-				slow_rc_osc: slow_rc_osc {
-					compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
-					#clock-cells = <0>;
-					clock-frequency = <32768>;
-					clock-accuracy = <50000000>;
-				};
-
-				clk32k: slck {
-					compatible = "atmel,at91sam9x5-clk-slow";
-					#clock-cells = <0>;
-					clocks = <&slow_rc_osc>, <&slow_osc>;
-				};
+				clocks = <&slow_xtal>;
+				#clock-cells = <0>;
 			};
 
 			mmc0: mmc@f0008000 {
@@ -439,7 +159,7 @@
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
 				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>;
 				dma-names = "rxtx";
-				clocks = <&mci0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "mci_clk";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -452,7 +172,7 @@
 				#size-cells = <0>;
 				reg = <0xf8008000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tcb_clk>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k>;
 				clock-names = "t0_clk", "slow_clk";
 			};
 
@@ -462,7 +182,7 @@
 				#size-cells = <0>;
 				reg = <0xf800c000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tcb_clk>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k>;
 				clock-names = "t0_clk", "slow_clk";
 			};
 
@@ -470,7 +190,7 @@
 				compatible = "atmel,at91sam9n12-hlcdc";
 				reg = <0xf8038000 0x2000>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 25>, <&pmc PMC_TYPE_SYSTEM 3>, <&clk32k>;
 				clock-names = "periph_clk", "sys_clk", "slow_clk";
 				status = "disabled";
 
@@ -499,7 +219,7 @@
 				reg = <0xffffec00 0x200>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 				#dma-cells = <2>;
-				clocks = <&dma0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
 				clock-names = "dma_clk";
 			};
 
@@ -817,7 +537,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioAB_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
 				};
 
 				pioB: gpio@fffff600 {
@@ -828,7 +548,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioAB_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
 				};
 
 				pioC: gpio@fffff800 {
@@ -839,7 +559,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioCD_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
 				};
 
 				pioD: gpio@fffffa00 {
@@ -850,17 +570,18 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioCD_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
 				};
 			};
 
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -874,7 +595,7 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
-				clocks = <&ssc0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -882,10 +603,11 @@
 			usart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
-				clocks = <&usart0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -893,10 +615,11 @@
 			usart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
-				clocks = <&usart1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -904,10 +627,11 @@
 			usart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
-				clocks = <&usart2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -915,10 +639,11 @@
 			usart3: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
-				clocks = <&usart3_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -934,7 +659,7 @@
 				#size-cells = <0>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_i2c0>;
-				clocks = <&twi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				status = "disabled";
 			};
 
@@ -949,7 +674,7 @@
 				#size-cells = <0>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_i2c1>;
-				clocks = <&twi1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
 				status = "disabled";
 			};
 
@@ -964,7 +689,7 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0>;
-				clocks = <&spi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
@@ -980,7 +705,7 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi1>;
-				clocks = <&spi1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
@@ -1009,7 +734,7 @@
 				reg = <0xf8034000 0x300>;
 				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
 				#pwm-cells = <3>;
-				clocks = <&pwm_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
 				status = "disabled";
 			};
 
@@ -1017,7 +742,7 @@
 				compatible = "atmel,at91sam9260-udc";
 				reg = <0xf803c000 0x4000>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
-				clocks = <&udphs_clk>, <&udpck>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_SYSTEM 7>;
 				clock-names = "pclk", "hclk";
 				status = "disabled";
 			};
@@ -1027,7 +752,7 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x00100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
 			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
@@ -1045,7 +770,7 @@
 				  0x3 0x0 0x40000000 0x10000000
 				  0x4 0x0 0x50000000 0x10000000
 				  0x5 0x0 0x60000000 0x10000000>;
-			clocks = <&mck>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			status = "disabled";
 
 			nand_controller: nand-controller {
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/microchip/at91sam9n12ek.dts
index ea5cef0b0974..4c644d4c6be7 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9n12ek.dts
@@ -17,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x8000000>;
 	};
 
@@ -59,7 +59,7 @@
 				wm8904: codec@1a {
 					compatible = "wlf,wm8904";
 					reg = <0x1a>;
-					clocks = <&pck0>;
+					clocks = <&pmc PMC_TYPE_SYSTEM 8>;
 					clock-names = "mclk";
 				};
 
@@ -119,7 +119,7 @@
 			spi0: spi@f0000000 {
 				status = "okay";
 				cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -226,10 +226,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		enter {
+		button-enter {
 			label = "Enter";
 			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
@@ -238,7 +238,7 @@
 	};
 
 	panel: panel {
-		compatible = "qiaodian,qd43003c0-40", "simple-panel";
+		compatible = "qiaodian,qd43003c0-40";
 		backlight = <&backlight>;
 		power-supply = <&panel_reg>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/microchip/at91sam9rl.dtsi
index 8643b7151565..7436b5c862b1 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9rl.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -38,16 +39,17 @@
 	};
 
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x04000000>;
 	};
@@ -65,7 +67,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -75,6 +77,9 @@
 	sram: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x10000>;
 	};
 
 	ahb {
@@ -171,6 +176,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -184,6 +190,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -197,6 +204,7 @@
 			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -210,6 +218,7 @@
 			usart3: serial@fffbc000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffbc000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -262,8 +271,6 @@
 			};
 
 			adc0: adc@fffd0000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9rl-adc";
 				reg = <0xfffd0000 0x100>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -273,34 +280,9 @@
 				atmel,adc-channels-used = <0x3f>;
 				atmel,adc-vref = <3300>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-res = <8 10>;
-				atmel,adc-res-names = "lowres", "highres";
-				atmel,adc-use-res = "highres";
-
-				trigger0 {
-					trigger-name = "timer-counter-0";
-					trigger-value = <0x1>;
-				};
-				trigger1 {
-					trigger-name = "timer-counter-1";
-					trigger-value = <0x3>;
-				};
-
-				trigger2 {
-					trigger-name = "timer-counter-2";
-					trigger-value = <0x5>;
-				};
-
-				trigger3 {
-					trigger-name = "external";
-					trigger-value = <0x13>;
-					trigger-external;
-				};
 			};
 
 			usb0: gadget@fffd4000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9rl-udc";
 				reg = <0x00600000 0x100000>,
 				      <0xfffd4000 0x4000>;
@@ -308,58 +290,6 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
 				clock-names = "pclk", "hclk";
 				status = "disabled";
-
-				ep@0 {
-					reg = <0>;
-					atmel,fifo-size = <64>;
-					atmel,nb-banks = <1>;
-				};
-
-				ep@1 {
-					reg = <1>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <2>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@2 {
-					reg = <2>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <2>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@3 {
-					reg = <3>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-				};
-
-				ep@4 {
-					reg = <4>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-				};
-
-				ep@5 {
-					reg = <5>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@6 {
-					reg = <6>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
 			};
 
 			dma0: dma-controller@ffffe600 {
@@ -397,6 +327,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -682,7 +613,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -721,7 +652,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -744,7 +675,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -767,7 +698,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -832,7 +763,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9rl-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -841,13 +772,13 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&clk32k>;
@@ -868,7 +799,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fffffd50 {
+			clk32k: clock-controller@fffffd50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffd50 0x4>;
 				clocks = <&slow_xtal>;
diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/microchip/at91sam9rlek.dts
index 0de75d3c4f18..a57351270551 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9rlek.dts
@@ -17,7 +17,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -180,7 +180,7 @@
 			spi0: spi@fffcc000 {
 				status = "okay";
 				cs-gpios = <&pioA 28 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <15000000>;
 					reg = <0>;
@@ -212,49 +212,53 @@
 				status = "okay";
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			rtc@fffffe00 {
 				status = "okay";
 			};
 		};
 	};
 
-	pwmleds {
+	led-controller-1 {
 		compatible = "pwm-leds";
 
-		ds1 {
+		led-1 {
 			label = "ds1";
 			pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 		};
 
-		ds2 {
+		led-2 {
 			label = "ds2";
 			pwms = <&pwm0 2 5000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 		};
 	};
 
-	leds {
+	led-controller-2 {
 		compatible = "gpio-leds";
 
-		ds3 {
+		led-3 {
 			label = "ds3";
 			gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			wakeup-source;
 		};
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
diff --git a/arch/arm/boot/dts/at91sam9x25.dtsi b/arch/arm/boot/dts/microchip/at91sam9x25.dtsi
index 0fe8802e1242..7036f5f04571 100644
--- a/arch/arm/boot/dts/at91sam9x25.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x25.dtsi
@@ -27,7 +27,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9x25-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9x25ek.dts b/arch/arm/boot/dts/microchip/at91sam9x25ek.dts
index ad7c6b36f0ba..ad7c6b36f0ba 100644
--- a/arch/arm/boot/dts/at91sam9x25ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9x25ek.dts
diff --git a/arch/arm/boot/dts/at91sam9x35.dtsi b/arch/arm/boot/dts/microchip/at91sam9x35.dtsi
index 0bfa21f18f87..eb03b0497e37 100644
--- a/arch/arm/boot/dts/at91sam9x35.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x35.dtsi
@@ -26,7 +26,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9x35-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9x35ek.dts b/arch/arm/boot/dts/microchip/at91sam9x35ek.dts
index 66675c787b97..66675c787b97 100644
--- a/arch/arm/boot/dts/at91sam9x35ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9x35ek.dts
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5.dtsi
index 7c2eb93f8cac..a7456c2191fa 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -39,16 +40,17 @@
 		pwm0 = &pwm0;
 	};
 	cpus {
-		#address-cells = <0>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu {
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x10000000>;
 	};
@@ -66,7 +68,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -76,6 +78,9 @@
 	sram: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x8000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x8000>;
 	};
 
 	ahb {
@@ -121,7 +126,7 @@
 				reg = <0xffffea00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9x5-pmc", "syscon";
 				reg = <0xfffffc00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -130,13 +135,13 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shdwc@fffffe10 {
+			shutdown_controller: poweroff@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
@@ -149,7 +154,7 @@
 				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			};
 
-			clk32k: sckc@fffffe50 {
+			clk32k: clock-controller@fffffe50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffe50 0x4>;
 				clocks = <&slow_xtal>;
@@ -647,7 +652,6 @@
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
 				dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(0)>;
 				dma-names = "rxtx";
-				pinctrl-names = "default";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "mci_clk";
 				#address-cells = <1>;
@@ -661,7 +665,6 @@
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
 				dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(0)>;
 				dma-names = "rxtx";
-				pinctrl-names = "default";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 26>;
 				clock-names = "mci_clk";
 				#address-cells = <1>;
@@ -672,6 +675,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -686,6 +690,7 @@
 			usart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
@@ -700,6 +705,7 @@
 			usart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
@@ -714,6 +720,7 @@
 			usart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
@@ -773,6 +780,7 @@
 			uart0: serial@f8040000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8040000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -784,6 +792,7 @@
 			uart1: serial@f8044000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8044000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
@@ -793,8 +802,6 @@
 			};
 
 			adc0: adc@f804c000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9x5-adc";
 				reg = <0xf804c000 0x100>;
 				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -806,32 +813,6 @@
 				atmel,adc-vref = <3300>;
 				atmel,adc-startup-time = <40>;
 				atmel,adc-sample-hold-time = <11>;
-				atmel,adc-res = <8 10>;
-				atmel,adc-res-names = "lowres", "highres";
-				atmel,adc-use-res = "highres";
-
-				trigger0 {
-					trigger-name = "external-rising";
-					trigger-value = <0x1>;
-					trigger-external;
-				};
-
-				trigger1 {
-					trigger-name = "external-falling";
-					trigger-value = <0x2>;
-					trigger-external;
-				};
-
-				trigger2 {
-					trigger-name = "external-any";
-					trigger-value = <0x3>;
-					trigger-external;
-				};
-
-				trigger3 {
-					trigger-name = "continuous";
-					trigger-value = <0x6>;
-				};
 			};
 
 			spi0: spi@f0000000 {
@@ -867,8 +848,6 @@
 			};
 
 			usb2: gadget@f803c000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "atmel,at91sam9g45-udc";
 				reg = <0x00500000 0x80000
 				       0xf803c000 0x400>;
@@ -876,58 +855,6 @@
 				clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 23>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
-
-				ep@0 {
-					reg = <0>;
-					atmel,fifo-size = <64>;
-					atmel,nb-banks = <1>;
-				};
-
-				ep@1 {
-					reg = <1>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <2>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@2 {
-					reg = <2>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <2>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@3 {
-					reg = <3>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-				};
-
-				ep@4 {
-					reg = <4>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-				};
-
-				ep@5 {
-					reg = <5>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
-
-				ep@6 {
-					reg = <6>;
-					atmel,fifo-size = <1024>;
-					atmel,nb-banks = <3>;
-					atmel,can-dma;
-					atmel,can-isoc;
-				};
 			};
 
 			watchdog: watchdog@fffffe40 {
diff --git a/arch/arm/boot/dts/at91sam9x5_can.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_can.dtsi
index 04ccb25d342c..04ccb25d342c 100644
--- a/arch/arm/boot/dts/at91sam9x5_can.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_can.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_isi.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_isi.dtsi
index 4ce98f05d7db..4ce98f05d7db 100644
--- a/arch/arm/boot/dts/at91sam9x5_isi.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_isi.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_lcd.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_lcd.dtsi
index f81c9d1691e0..f81c9d1691e0 100644
--- a/arch/arm/boot/dts/at91sam9x5_lcd.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_lcd.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_macb0.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_macb0.dtsi
index 222aa30f6860..222aa30f6860 100644
--- a/arch/arm/boot/dts/at91sam9x5_macb0.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_macb0.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_macb1.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_macb1.dtsi
index 26bf9b5de9ee..26bf9b5de9ee 100644
--- a/arch/arm/boot/dts/at91sam9x5_macb1.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_macb1.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_usart3.dtsi
index 098d3fef5c37..a47c765e1b20 100644
--- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_usart3.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	aliases {
@@ -44,6 +45,7 @@
 			usart3: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
diff --git a/arch/arm/boot/dts/at91sam9x5cm.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5cm.dtsi
index 75d2f7fd314f..cdd37f67280b 100644
--- a/arch/arm/boot/dts/at91sam9x5cm.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5cm.dtsi
@@ -7,7 +7,7 @@
  */
 
 / {
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x8000000>;
 	};
 
diff --git a/arch/arm/boot/dts/at91sam9x5dm.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5dm.dtsi
index 7f00c1f57b90..a9278038af3b 100644
--- a/arch/arm/boot/dts/at91sam9x5dm.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5dm.dtsi
@@ -27,7 +27,7 @@
 	};
 
 	panel: panel {
-		compatible = "foxlink,fl500wvr00-a0t", "simple-panel";
+		compatible = "foxlink,fl500wvr00-a0t";
 		backlight = <&backlight>;
 		power-supply = <&panel_reg>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5ek.dtsi
index c934928742b0..5f4eaa618ab4 100644
--- a/arch/arm/boot/dts/at91sam9x5ek.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5ek.dtsi
@@ -56,6 +56,7 @@
 		&pinctrl_board_mmc0
 		&pinctrl_mmc0_slot0_clk_cmd_dat0
 		&pinctrl_mmc0_slot0_dat1_3>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	slot@0 {
@@ -70,6 +71,7 @@
 		&pinctrl_board_mmc1
 		&pinctrl_mmc1_slot0_clk_cmd_dat0
 		&pinctrl_mmc1_slot0_dat1_3>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	slot@0 {
@@ -123,7 +125,7 @@
 	cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
 	status = "disabled"; /* conflicts with mmc1 */
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "atmel,at25df321a";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/at91sam9xe.dtsi b/arch/arm/boot/dts/microchip/at91sam9xe.dtsi
index 3f9d8caf8b0a..f571f77779c3 100644
--- a/arch/arm/boot/dts/at91sam9xe.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9xe.dtsi
@@ -19,5 +19,8 @@
 	sram1: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x4000>;
 	};
 };
diff --git a/arch/arm/boot/dts/ethernut5.dts b/arch/arm/boot/dts/microchip/ethernut5.dts
index 052a52f947ce..ad7a0850252a 100644
--- a/arch/arm/boot/dts/ethernut5.dts
+++ b/arch/arm/boot/dts/microchip/ethernut5.dts
@@ -15,7 +15,7 @@
 		bootargs = "console=ttyS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x08000000>;
 	};
 
diff --git a/arch/arm/boot/dts/evk-pro3.dts b/arch/arm/boot/dts/microchip/evk-pro3.dts
index 6d519d02d190..6d519d02d190 100644
--- a/arch/arm/boot/dts/evk-pro3.dts
+++ b/arch/arm/boot/dts/microchip/evk-pro3.dts
diff --git a/arch/arm/boot/dts/ge863-pro3.dtsi b/arch/arm/boot/dts/microchip/ge863-pro3.dtsi
index dbba33e5a06c..dbba33e5a06c 100644
--- a/arch/arm/boot/dts/ge863-pro3.dtsi
+++ b/arch/arm/boot/dts/microchip/ge863-pro3.dtsi
diff --git a/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts
new file mode 100644
index 000000000000..0f555eb45bda
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for the Kontron KSwitch D10 MMT 6G-2GS
+ */
+
+/dts-v1/;
+#include "lan966x-kontron-kswitch-d10-mmt.dtsi"
+
+/ {
+	model = "Kontron KSwitch D10 MMT 6G-2GS";
+	compatible = "kontron,kswitch-d10-mmt-6g-2gs", "kontron,s1921",
+		     "microchip,lan9668", "microchip,lan966";
+
+	aliases {
+		i2c0 = &i2c4;
+		i2c1 = &i2c1;
+	};
+
+	sfp0: sfp0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c4>;
+		los-gpios = <&sgpio_in 1 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 1 1 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <2500>;
+		tx-disable-gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 0 2 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&sgpio_out 2 0 GPIO_ACTIVE_HIGH>;
+		rate-select1-gpios = <&sgpio_out 2 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp1: sfp1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpios = <&sgpio_in 1 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 1 3 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <2500>;
+		tx-disable-gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 0 3 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&sgpio_out 2 2 GPIO_ACTIVE_HIGH>;
+		rate-select1-gpios = <&sgpio_out 2 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c1: i2c@600 {
+		pinctrl-0 = <&fc1_c_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c4: i2c@600 {
+		pinctrl-0 = <&fc4_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&gpio {
+	fc1_c_pins: fc1-c-i2c-pins {
+		/* SCL, SDA */
+		pins = "GPIO_47", "GPIO_48";
+		function = "fc1_c";
+	};
+
+	fc4_b_pins: fc4-b-i2c-pins {
+		/* SCL, SDA */
+		pins = "GPIO_57", "GPIO_58";
+		function = "fc4_b";
+	};
+};
+
+&port2 {
+	phys = <&serdes 2 SERDES6G(0)>;
+	sfp = <&sfp0>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&port3 {
+	phys = <&serdes 3 SERDES6G(1)>;
+	sfp = <&sfp1>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-8g.dts b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-8g.dts
new file mode 100644
index 000000000000..ad5d8b56e6fa
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-8g.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for the Kontron KSwitch D10 MMT 8G
+ */
+
+/dts-v1/;
+#include "lan966x-kontron-kswitch-d10-mmt.dtsi"
+
+/ {
+	model = "Kontron KSwitch D10 MMT 8G";
+	compatible = "kontron,kswitch-d10-mmt-8g", "kontron,s1921",
+		     "microchip,lan9668", "microchip,lan966";
+};
+
+&mdio0 {
+	phy2: ethernet-phy@3 {
+		reg = <3>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	phy3: ethernet-phy@4 {
+		reg = <4>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&port2 {
+	phys = <&serdes 2 SERDES6G(0)>;
+	phy-handle = <&phy2>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&port3 {
+	phys = <&serdes 3 SERDES6G(1)>;
+	phy-handle = <&phy3>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt.dtsi b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt.dtsi
new file mode 100644
index 000000000000..426893750d51
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt.dtsi
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common part of the device tree for the Kontron KSwitch D10 MMT
+ */
+
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	aliases {
+		serial0 = &usart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		pinctrl-0 = <&reset_pins>;
+		pinctrl-names = "default";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart0: serial@200 {
+		pinctrl-0 = <&usart0_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi3: spi@400 {
+		pinctrl-0 = <&fc3_b_pins>, <&spi3_cs_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+		cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&phy_int_pins>;
+	pinctrl-names = "default";
+
+	fc3_b_pins: fc3-b-pins {
+		/* SCK, MISO, MOSI */
+		pins = "GPIO_51", "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	miim_c_pins: miim-c-pins {
+		/* MDC, MDIO */
+		pins = "GPIO_59", "GPIO_60";
+		function = "miim_c";
+	};
+
+	phy_int_pins: phy-int-pins {
+		/* PHY_INT# */
+		pins = "GPIO_24";
+		function = "gpio";
+	};
+
+	reset_pins: reset-pins {
+		/* SYS_RST# */
+		pins = "GPIO_56";
+		function = "gpio";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1 */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34";
+		function = "sgpio_a";
+	};
+
+	sgpio_b_pins: sgpio-b-pins {
+		/* LD */
+		pins = "GPIO_64";
+		function = "sgpio_b";
+	};
+
+	spi3_cs_pins: spi3-cs-pins {
+		/* CS# */
+		pins = "GPIO_46";
+		function = "gpio";
+	};
+
+	usart0_pins: usart0-pins {
+		/* RXD, TXD */
+		pins = "GPIO_25", "GPIO_26";
+		function = "fc0_b";
+	};
+
+	usbs_a_pins: usbs-a-pins {
+		/* VBUS_DET */
+		pins = "GPIO_66";
+		function = "gpio";
+	};
+};
+
+&mdio0 {
+	pinctrl-0 = <&miim_c_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+	clock-frequency = <2500000>;
+	status = "okay";
+
+	phy4: ethernet-phy@5 {
+		reg = <5>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy5: ethernet-phy@6 {
+		reg = <6>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy6: ethernet-phy@7 {
+		reg = <7>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy7: ethernet-phy@8 {
+		reg = <8>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phys = <&serdes 0 CU(0)>;
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&port1 {
+	phys = <&serdes 1 CU(1)>;
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&port4 {
+	phys = <&serdes 4 SERDES6G(2)>;
+	phy-handle = <&phy4>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port5 {
+	phys = <&serdes 5 SERDES6G(2)>;
+	phy-handle = <&phy5>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port6 {
+	phys = <&serdes 6 SERDES6G(2)>;
+	phy-handle = <&phy6>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port7 {
+	phys = <&serdes 7 SERDES6G(2)>;
+	phy-handle = <&phy7>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>, <&sgpio_b_pins>;
+	pinctrl-names = "default";
+	bus-frequency = <8000000>;
+	/* arbitrary range because all GPIOs are in software mode */
+	microchip,sgpio-port-ranges = <0 11>;
+	status = "okay";
+
+	sgpio_in: gpio@0 {
+		ngpios = <128>;
+	};
+
+	sgpio_out: gpio@1 {
+		ngpios = <128>;
+	};
+};
+
+&switch {
+	status = "okay";
+};
+
+&udc {
+	pinctrl-0 = <&usbs_a_pins>;
+	pinctrl-names = "default";
+	atmel,vbus-gpio = <&gpio 66 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8290.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8290.dts
new file mode 100644
index 000000000000..3b7577e48b46
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-pcb8290.dts
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x-pcb8290.dts - Device Tree file for LAN966X-PCB8290 board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Horatiu Vultur <horatiu.vultur@microchip.com>
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB LAN9668";
+	compatible = "microchip,lan9668-pcb8290", "microchip,lan9668", "microchip,lan966";
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&gpio {
+	miim_a_pins: mdio-pins {
+		/* MDC, MDIO */
+		pins = "GPIO_28", "GPIO_29";
+		function = "miim_a";
+	};
+
+	pps_out_pins: pps-out-pins {
+		/* 1pps output */
+		pins = "GPIO_38";
+		function = "ptpsync_3";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		/* 1pps input */
+		pins = "GPIO_35";
+		function = "ptpsync_0";
+	};
+
+	udc_pins: ucd-pins {
+		/* VBUS_DET B */
+		pins = "GPIO_8";
+		function = "usb_slave_b";
+	};
+};
+
+&mdio0 {
+	pinctrl-0 = <&miim_a_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ext_phy0: ethernet-phy@7 {
+		reg = <7>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy1: ethernet-phy@8 {
+		reg = <8>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy2: ethernet-phy@9 {
+		reg = <9>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy3: ethernet-phy@10 {
+		reg = <10>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy4: ethernet-phy@15 {
+		reg = <15>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy5: ethernet-phy@16 {
+		reg = <16>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy6: ethernet-phy@17 {
+		reg = <17>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy7: ethernet-phy@18 {
+		reg = <18>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+};
+
+&port0 {
+	reg = <2>;
+	phy-handle = <&ext_phy2>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 0 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port1 {
+	reg = <3>;
+	phy-handle = <&ext_phy3>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 1 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port2 {
+	reg = <0>;
+	phy-handle = <&ext_phy0>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 2 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port3 {
+	reg = <1>;
+	phy-handle = <&ext_phy1>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 3 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port4 {
+	reg = <6>;
+	phy-handle = <&ext_phy6>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 4 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port5 {
+	reg = <7>;
+	phy-handle = <&ext_phy7>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 5 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port6 {
+	reg = <4>;
+	phy-handle = <&ext_phy4>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 6 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port7 {
+	reg = <5>;
+	phy-handle = <&ext_phy5>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 7 SERDES6G(2)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&switch {
+	pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&udc {
+	pinctrl-0 = <&udc_pins>;
+	pinctrl-names = "default";
+	atmel,vbus-gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
new file mode 100644
index 000000000000..3a3d76af8612
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x_pcb8291.dts - Device Tree file for PCB8291
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB - LAN9662";
+	compatible = "microchip,lan9662-pcb8291", "microchip,lan9662", "microchip,lan966";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &usart3;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-s0-blue {
+			label = "s0:blue";
+			gpios = <&sgpio_out 2 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s0-green {
+			label = "s0:green";
+			gpios = <&sgpio_out 2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-blue {
+			label = "s1:blue";
+			gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-green {
+			label = "s1:green";
+			gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* RX, TX */
+		pins = "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	can0_b_pins:  can0-b-pins {
+		/* RX, TX */
+		pins = "GPIO_35", "GPIO_36";
+		function = "can0_b";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34", "GPIO_35";
+		function = "sgpio_a";
+	};
+};
+
+&can0 {
+	pinctrl-0 = <&can0_b_pins>;
+	pinctrl-names = "default";
+	status = "disabled"; /* Conflict with switch */
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart3: serial@200 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	phys = <&serdes 0 CU(0)>;
+	status = "okay";
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	phys = <&serdes 1 CU(1)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 3>, <8 11>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&switch {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8309.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8309.dts
new file mode 100644
index 000000000000..0cb505f79ba1
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-pcb8309.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x_pcb8309.dts - Device Tree file for PCB8309
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB - LAN9662";
+	compatible = "microchip,lan9662-pcb8309", "microchip,lan9662", "microchip,lan966";
+
+	aliases {
+		serial0 = &usart3;
+		i2c102 = &i2c102;
+		i2c103 = &i2c103;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-controls = <&mux>;
+		i2c-parent = <&i2c4>;
+
+		i2c102: i2c-sfp@1 {
+			reg = <1>;
+		};
+
+		i2c103: i2c-sfp@2 {
+			reg = <2>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-s0-green {
+			label = "s0:green";
+			gpios = <&sgpio_out 2 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s0-red {
+			label = "s0:red";
+			gpios = <&sgpio_out 2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-green {
+			label = "s1:green";
+			gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-red {
+			label = "s1:red";
+			gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+
+		mux-gpios = <&sgpio_out 11 0 GPIO_ACTIVE_HIGH>, /* p11b0 */
+			    <&sgpio_out 11 1 GPIO_ACTIVE_HIGH>; /* p11b1 */
+	};
+
+	sfp2: sfp2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c102>;
+		tx-disable-gpios = <&sgpio_out 10 0 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sgpio_in  2 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in  2 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in  1 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp3: sfp3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c103>;
+		tx-disable-gpios = <&sgpio_out 10 1 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sgpio_in  3 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in  3 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in  1 1 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart3: serial@200 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c4: i2c@600 {
+		compatible = "microchip,sam9x60-i2c";
+		reg = <0x600 0x200>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&nic_clk>;
+		pinctrl-0 = <&fc4_b_pins>;
+		pinctrl-names = "default";
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		i2c-sda-hold-time-ns = <1500>;
+		status = "okay";
+	};
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* RXD, TXD */
+		pins = "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	fc4_b_pins: fc4-b-pins {
+		/* SCL, SDA */
+		pins = "GPIO_57", "GPIO_58";
+		function = "fc4_b";
+	};
+
+	pps_out_pins: pps-out-pins {
+		/* 1pps output */
+		pins = "GPIO_38";
+		function = "ptpsync_3";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		/* 1pps input */
+		pins = "GPIO_39";
+		function = "ptpsync_4";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34", "GPIO_35";
+		function = "sgpio_a";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	phys = <&serdes 0 CU(0)>;
+	status = "okay";
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	phys = <&serdes 1 CU(1)>;
+	status = "okay";
+};
+
+&port2 {
+	sfp = <&sfp2>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	phys = <&serdes 2 SERDES6G(0)>;
+	status = "okay";
+};
+
+&port3 {
+	sfp = <&sfp3>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	phys = <&serdes 3 SERDES6G(1)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 3>, <8 11>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&switch {
+	pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x.dtsi b/arch/arm/boot/dts/microchip/lan966x.dtsi
new file mode 100644
index 000000000000..05b73f7cf0c7
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x.dtsi
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x.dtsi - Device Tree Include file for Microchip LAN966 family SoC
+ *
+ * Copyright (C) 2021 Microchip Technology, Inc. and its subsidiaries
+ *
+ * Author: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/microchip,lan966x.h>
+
+/ {
+	model = "Microchip LAN966 family SoC";
+	compatible = "microchip,lan966";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			clock-frequency = <600000000>;
+			reg = <0x0>;
+		};
+	};
+
+	clocks {
+		sys_clk: sys_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <165625000>;
+		};
+
+		cpu_clk: cpu_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <600000000>;
+		};
+
+		ddr_clk: ddr_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <300000000>;
+		};
+
+		nic_clk: nic_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	clks: clock-controller@e00c00a8 {
+		compatible = "microchip,lan966x-gck";
+		#clock-cells = <1>;
+		clocks = <&cpu_clk>, <&ddr_clk>, <&sys_clk>;
+		clock-names = "cpu", "ddr", "sys";
+		reg = <0xe00c00a8 0x38>, <0xe00c02cc 0x4>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <37500000>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		udc: usb@200000 {
+			compatible = "microchip,lan9662-udc",
+				     "atmel,sama5d3-udc";
+			reg = <0x00200000 0x80000>,
+			      <0xe0808000 0x400>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks GCK_GATE_UDPHS>, <&nic_clk>;
+			clock-names = "pclk", "hclk";
+			status = "disabled";
+		};
+
+		switch: switch@e0000000 {
+			compatible = "microchip,lan966x-switch";
+			reg = <0xe0000000 0x0100000>,
+			      <0xe2000000 0x0800000>;
+			reg-names = "cpu", "gcb";
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "xtr", "fdma", "ana", "ptp",
+					  "ptp-ext";
+			resets = <&reset 0>;
+			reset-names = "switch";
+			status = "disabled";
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port0: port@0 {
+					reg = <0>;
+					status = "disabled";
+				};
+
+				port1: port@1 {
+					reg = <1>;
+					status = "disabled";
+				};
+
+				port2: port@2 {
+					reg = <2>;
+					status = "disabled";
+				};
+
+				port3: port@3 {
+					reg = <3>;
+					status = "disabled";
+				};
+
+				port4: port@4 {
+					reg = <4>;
+					status = "disabled";
+				};
+
+				port5: port@5 {
+					reg = <5>;
+					status = "disabled";
+				};
+
+				port6: port@6 {
+					reg = <6>;
+					status = "disabled";
+				};
+
+				port7: port@7 {
+					reg = <7>;
+					status = "disabled";
+				};
+			};
+		};
+
+		otp: otp@e0021000 {
+			compatible = "microchip,lan9668-otpc", "microchip,lan9662-otpc";
+			reg = <0xe0021000 0x300>;
+		};
+
+		flx0: flexcom@e0040000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0040000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0040000 0x800>;
+			status = "disabled";
+
+			usart0: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e0044000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0044000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0044000 0x800>;
+			status = "disabled";
+
+			usart1: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		trng: rng@e0048000 {
+			compatible = "atmel,at91sam9g45-trng";
+			reg = <0xe0048000 0x100>;
+			clocks = <&nic_clk>;
+		};
+
+		aes: crypto@e004c000 {
+			compatible = "atmel,at91sam9g46-aes";
+			reg = <0xe004c000 0x100>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(13)>;
+			dma-names = "tx", "rx";
+			clocks = <&nic_clk>;
+			clock-names = "aes_clk";
+		};
+
+		flx2: flexcom@e0060000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0060000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0060000 0x800>;
+			status = "disabled";
+
+			usart2: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e0064000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0064000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM3>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0064000 0x800>;
+			status = "disabled";
+
+			usart3: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		dma0: dma-controller@e0068000 {
+			compatible = "microchip,sama7g5-dma";
+			reg = <0xe0068000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&nic_clk>;
+			clock-names = "dma_clk";
+		};
+
+		sha: crypto@e006c000 {
+			compatible = "atmel,at91sam9g46-sha";
+			reg = <0xe006c000 0xec>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>;
+			dma-names = "tx";
+			clocks = <&nic_clk>;
+			clock-names = "sha_clk";
+		};
+
+		flx4: flexcom@e0070000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0070000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0070000 0x800>;
+			status = "disabled";
+
+			usart4: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		timer0: timer@e008c000 {
+			compatible = "snps,dw-apb-timer";
+			reg = <0xe008c000 0x400>;
+			clocks = <&nic_clk>;
+			clock-names = "timer";
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		watchdog: watchdog@e0090000 {
+			compatible = "snps,dw-wdt";
+			reg = <0xe0090000 0x1000>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&nic_clk>;
+			status = "disabled";
+		};
+
+		cpu_ctrl: syscon@e00c0000 {
+			compatible = "microchip,lan966x-cpu-syscon", "syscon";
+			reg = <0xe00c0000 0x350>;
+		};
+
+		can0: can@e081c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe081c000 0xfc>, <0x00100000 0x4000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&clks GCK_ID_MCAN0>, <&clks GCK_ID_MCAN0>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&clks GCK_ID_MCAN0>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@e0820000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0820000 0xfc>, <0x00100000 0x8000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&clks GCK_ID_MCAN1>, <&clks GCK_ID_MCAN1>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&clks GCK_ID_MCAN1>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x4000 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		reset: reset-controller@e200400c {
+			compatible = "microchip,lan966x-switch-reset";
+			reg = <0xe200400c 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
+		};
+
+		gpio: pinctrl@e2004064 {
+			compatible = "microchip,lan966x-pinctrl";
+			reg = <0xe2004064 0xb4>,
+			    <0xe2010024 0x138>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 78>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+		};
+
+		mdio0: mdio@e2004118 {
+			compatible = "microchip,lan966x-miim";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe2004118 0x24>;
+			clocks = <&sys_clk>;
+			status = "disabled";
+		};
+
+		mdio1: mdio@e200413c {
+			compatible = "microchip,lan966x-miim";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe200413c 0x24>,
+			      <0xe2010020 0x4>;
+			clocks = <&sys_clk>;
+			status = "disabled";
+
+			phy0: ethernet-phy@1 {
+				reg = <1>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			phy1: ethernet-phy@2 {
+				reg = <2>;
+				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		sgpio: gpio@e2004190 {
+			compatible = "microchip,sparx5-sgpio";
+			reg = <0xe2004190 0x118>;
+			clocks = <&sys_clk>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgpio_in: gpio@0 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+			};
+
+			sgpio_out: gpio@1 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+			};
+		};
+
+		hwmon: hwmon@e2010180 {
+			compatible = "microchip,lan9668-hwmon";
+			reg = <0xe2010180 0xc>,
+			      <0xe20042a8 0xc>;
+			reg-names = "pvt", "fan";
+			clocks = <&sys_clk>;
+		};
+
+		serdes: serdes@e202c000 {
+			compatible = "microchip,lan966x-serdes";
+			reg = <0xe202c000 0x9c>,
+			      <0xe2004010 0x4>;
+			#phy-cells = <2>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,gic-400", "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			reg = <0xe8c11000 0x1000>,
+			      <0xe8c12000 0x2000>,
+			      <0xe8c14000 0x2000>,
+			      <0xe8c16000 0x2000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/mpa1600.dts b/arch/arm/boot/dts/microchip/mpa1600.dts
index a5c91c240db9..005c2758e229 100644
--- a/arch/arm/boot/dts/mpa1600.dts
+++ b/arch/arm/boot/dts/microchip/mpa1600.dts
@@ -11,7 +11,7 @@
 	model = "Phontech MPA 1600";
 	compatible = "phontech,mpa1600", "atmel,at91rm9200";
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/microchip/pm9g45.dts
index 4dfe0f15d7bd..c349fd3758a6 100644
--- a/arch/arm/boot/dts/pm9g45.dts
+++ b/arch/arm/boot/dts/microchip/pm9g45.dts
@@ -15,7 +15,7 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	memory {
+	memory@70000000 {
 		reg = <0x70000000 0x8000000>;
 	};
 
@@ -68,6 +68,7 @@
 					&pinctrl_board_mmc
 					&pinctrl_mmc0_slot0_clk_cmd_dat0
 					&pinctrl_mmc0_slot0_dat1_3>;
+				pinctrl-names = "default";
 				status = "okay";
 				slot@0 {
 					reg = <0>;
diff --git a/arch/arm/boot/dts/microchip/sam9x60.dtsi b/arch/arm/boot/dts/microchip/sam9x60.dtsi
new file mode 100644
index 000000000000..73d570a17269
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sam9x60.dtsi
@@ -0,0 +1,1353 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x60.dtsi - Device Tree Include file for Microchip SAM9X60 SoC
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Sandeep Sheriker M <sandeepsheriker.mallikarjun@microchip.com>
+ */
+
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Microchip SAM9X60 SoC";
+	compatible = "microchip,sam9x60";
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+		tcb0 = &tcb0;
+		tcb1 = &tcb1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x10000000>;
+	};
+
+	clocks {
+		slow_xtal: slow_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		main_xtal: main_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+	};
+
+	sram: sram@300000 {
+		compatible = "mmio-sram";
+		reg = <0x00300000 0x100000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x100000>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		usb0: gadget@500000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "microchip,sam9x60-udc";
+			reg = <0x00500000 0x100000
+				0xf803c000 0x400>;
+			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			clock-names = "pclk", "hclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			assigned-clock-rates = <480000000>;
+			status = "disabled";
+		};
+
+		usb1: ohci@600000 {
+			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+			reg = <0x00600000 0x100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
+			status = "disabled";
+		};
+
+		usb2: ehci@700000 {
+			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+			reg = <0x00700000 0x100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
+			clock-names = "usb_clk", "ehci_clk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			assigned-clock-rates = <480000000>;
+			status = "disabled";
+		};
+
+		ebi: ebi@10000000 {
+			compatible = "microchip,sam9x60-ebi";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			atmel,smc = <&smc>;
+			microchip,sfr = <&sfr>;
+			reg = <0x10000000 0x60000000>;
+			ranges = <0x0 0x0 0x10000000 0x10000000
+				  0x1 0x0 0x20000000 0x10000000
+				  0x2 0x0 0x30000000 0x10000000
+				  0x3 0x0 0x40000000 0x10000000
+				  0x4 0x0 0x50000000 0x10000000
+				  0x5 0x0 0x60000000 0x10000000>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
+			status = "disabled";
+
+			nand_controller: nand-controller {
+				compatible = "microchip,sam9x60-nand-controller";
+				ecc-engine = <&pmecc>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				ranges;
+				status = "disabled";
+			};
+		};
+
+		sdmmc0: sdio-host@80000000 {
+			compatible = "microchip,sam9x60-sdhci";
+			reg = <0x80000000 0x300>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		sdmmc1: sdio-host@90000000 {
+			compatible = "microchip,sam9x60-sdhci";
+			reg = <0x90000000 0x300>;
+			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			flx4: flexcom@f0000000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0000000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0000000 0x800>;
+				status = "disabled";
+
+				uart4: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi4: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c4: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx5: flexcom@f0004000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0004000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0004000 0x800>;
+				status = "disabled";
+
+				uart5: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi5: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c5: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			dma0: dma-controller@f0008000 {
+				compatible = "microchip,sam9x60-dma", "atmel,sama5d4-dma";
+				reg = <0xf0008000 0x1000>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+				#dma-cells = <1>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+				clock-names = "dma_clk";
+			};
+
+			ssc: ssc@f0010000 {
+				compatible = "atmel,at91sam9g45-ssc";
+				reg = <0xf0010000 0x4000>;
+				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(38))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(39))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+				clock-names = "pclk";
+				status = "disabled";
+			};
+
+			qspi: spi@f0014000 {
+				compatible = "microchip,sam9x60-qspi";
+				reg = <0xf0014000 0x100>, <0x70000000 0x10000000>;
+				reg-names = "qspi_base", "qspi_mmap";
+				interrupts = <35 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(26))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(27))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_SYSTEM 19>;
+				clock-names = "pclk", "qspick";
+				atmel,pmc = <&pmc>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2s: i2s@f001c000 {
+				compatible = "microchip,sam9x60-i2smcc";
+				reg = <0xf001c000 0x100>;
+				interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(36))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(37))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
+			flx11: flexcom@f0020000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0020000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0020000 0x800>;
+				status = "disabled";
+
+				uart11: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c11: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx12: flexcom@f0024000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0024000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0024000 0x800>;
+				status = "disabled";
+
+				uart12: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c12: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			pit64b: timer@f0028000 {
+				compatible = "microchip,sam9x60-pit64b";
+				reg = <0xf0028000 0x100>;
+				interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+				clock-names = "pclk", "gclk";
+			};
+
+			sha: crypto@f002c000 {
+				compatible = "atmel,at91sam9g46-sha";
+				reg = <0xf002c000 0x100>;
+				interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(34))>;
+				dma-names = "tx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+				clock-names = "sha_clk";
+			};
+
+			trng: trng@f0030000 {
+				compatible = "microchip,sam9x60-trng";
+				reg = <0xf0030000 0x100>;
+				interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			};
+
+			aes: crypto@f0034000 {
+				compatible = "atmel,at91sam9g46-aes";
+				reg = <0xf0034000 0x100>;
+				interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(32))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(33))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				clock-names = "aes_clk";
+			};
+
+			tdes: crypto@f0038000 {
+				compatible = "atmel,at91sam9g46-tdes";
+				reg = <0xf0038000 0x100>;
+				interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(31))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(30))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+				clock-names = "tdes_clk";
+			};
+
+			classd: classd@f003c000 {
+				compatible = "atmel,sama5d2-classd";
+				reg = <0xf003c000 0x100>;
+				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(35))>;
+				dma-names = "tx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
+			can0: can@f8000000 {
+				compatible = "microchip,sam9x60-can", "atmel,at91sam9x5-can";
+				reg = <0xf8000000 0x300>;
+				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 29>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
+
+			can1: can@f8004000 {
+				compatible = "microchip,sam9x60-can", "atmel,at91sam9x5-can";
+				reg = <0xf8004000 0x300>;
+				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 30>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
+
+			tcb0: timer@f8008000 {
+				compatible = "microchip,sam9x60-tcb", "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0xf8008000 0x100>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k 0>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
+			tcb1: timer@f800c000 {
+				compatible = "microchip,sam9x60-tcb", "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0xf800c000 0x100>;
+				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 45>, <&clk32k 0>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
+			flx6: flexcom@f8010000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8010000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8010000 0x800>;
+				status = "disabled";
+
+				uart6: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c6: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx7: flexcom@f8014000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8014000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8014000 0x800>;
+				status = "disabled";
+
+				uart7: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c7: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx8: flexcom@f8018000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8018000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8018000 0x800>;
+				status = "disabled";
+
+				uart8: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c8: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx0: flexcom@f801c000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf801c000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf801c000 0x800>;
+				status = "disabled";
+
+				uart0: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi0: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c0: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx1: flexcom@f8020000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8020000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8020000 0x800>;
+				status = "disabled";
+
+				uart1: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi1: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c1: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx2: flexcom@f8024000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8024000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8024000 0x800>;
+				status = "disabled";
+
+				uart2: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi2: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c2: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx3: flexcom@f8028000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8028000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8028000 0x800>;
+				status = "disabled";
+
+				uart3: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi3: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c3: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			macb0: ethernet@f802c000 {
+				compatible = "cdns,sam9x60-macb", "cdns,macb";
+				reg = <0xf802c000 0x1000>;
+				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>;
+				clock-names = "hclk", "pclk";
+				status = "disabled";
+			};
+
+			macb1: ethernet@f8030000 {
+				compatible = "cdns,sam9x60-macb", "cdns,macb";
+				reg = <0xf8030000 0x1000>;
+				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_PERIPHERAL 27>;
+				clock-names = "hclk", "pclk";
+				status = "disabled";
+			};
+
+			pwm0: pwm@f8034000 {
+				compatible = "microchip,sam9x60-pwm";
+				reg = <0xf8034000 0x300>;
+				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			hlcdc: hlcdc@f8038000 {
+				compatible = "microchip,sam9x60-hlcdc";
+				reg = <0xf8038000 0x4000>;
+				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 25>, <&pmc PMC_TYPE_GCK 25>, <&clk32k 1>;
+				clock-names = "periph_clk","sys_clk", "slow_clk";
+				assigned-clocks = <&pmc PMC_TYPE_GCK 25>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_MCK>;
+				status = "disabled";
+
+				hlcdc-display-controller {
+					compatible = "atmel,hlcdc-display-controller";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						#address-cells = <1>;
+						#size-cells = <0>;
+						reg = <0>;
+					};
+				};
+
+				hlcdc_pwm: hlcdc-pwm {
+					compatible = "atmel,hlcdc-pwm";
+					#pwm-cells = <3>;
+				};
+			};
+
+			flx9: flexcom@f8040000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8040000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8040000 0x800>;
+				status = "disabled";
+
+				uart9: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c9: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx10: flexcom@f8044000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8044000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8044000 0x800>;
+				status = "disabled";
+
+				uart10: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c10: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			isi: isi@f8048000 {
+				compatible = "microchip,sam9x60-isi", "atmel,at91sam9g45-isi";
+				reg = <0xf8048000 0x100>;
+				interrupts = <43 IRQ_TYPE_LEVEL_HIGH 5>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+				clock-names = "isi_clk";
+				status = "disabled";
+				port {
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+
+			adc: adc@f804c000 {
+				compatible = "microchip,sam9x60-adc", "atmel,sama5d2-adc";
+				reg = <0xf804c000 0x100>;
+				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+				clock-names = "adc_clk";
+				dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(40))>;
+				dma-names = "rx";
+				atmel,min-sample-rate-hz = <200000>;
+				atmel,max-sample-rate-hz = <20000000>;
+				atmel,startup-time-ms = <4>;
+				atmel,trigger-edge-type = <IRQ_TYPE_EDGE_RISING>;
+				#io-channel-cells = <1>;
+				status = "disabled";
+			};
+
+			sfr: sfr@f8050000 {
+				compatible = "microchip,sam9x60-sfr", "syscon";
+				reg = <0xf8050000 0x100>;
+			};
+
+			matrix: matrix@ffffde00 {
+				compatible = "microchip,sam9x60-matrix", "atmel,at91sam9x5-matrix", "syscon";
+				reg = <0xffffde00 0x200>;
+			};
+
+			pmecc: ecc-engine@ffffe000 {
+				compatible = "microchip,sam9x60-pmecc", "atmel,at91sam9g45-pmecc";
+				reg = <0xffffe000 0x300>,
+				      <0xffffe600 0x100>;
+			};
+
+			mpddrc: mpddrc@ffffe800 {
+				compatible = "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
+				reg = <0xffffe800 0x200>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 49>;
+				clock-names = "ddrck", "mpddr";
+			};
+
+			smc: smc@ffffea00 {
+				compatible = "microchip,sam9x60-smc", "atmel,at91sam9260-smc", "syscon";
+				reg = <0xffffea00 0x100>;
+			};
+
+			aic: interrupt-controller@fffff100 {
+				compatible = "microchip,sam9x60-aic";
+				#interrupt-cells = <3>;
+				interrupt-controller;
+				reg = <0xfffff100 0x100>;
+				atmel,external-irqs = <31>;
+			};
+
+			dbgu: serial@fffff200 {
+				compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(28))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(29))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			pinctrl: pinctrl@fffff400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "microchip,sam9x60-pinctrl", "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+				ranges = <0xfffff400 0xfffff400 0x800>;
+
+				/* mux-mask corresponding to sam9x60 SoC in TFBGA228L package */
+				atmel,mux-mask = <
+						 /*	A	B	C	*/
+						 0xffffffff 0xffe03fff 0xef00019d	/* pioA */
+						 0x03ffffff 0x02fc7e7f 0x00780000	/* pioB */
+						 0xffffffff 0xffffffff 0xf83fffff	/* pioC */
+						 0x003fffff 0x003f8000 0x00000000	/* pioD */
+						 >;
+
+				pioA: gpio@fffff400 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff400 0x200>;
+					interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+				};
+
+				pioB: gpio@fffff600 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff600 0x200>;
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					#gpio-lines = <26>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+				};
+
+				pioC: gpio@fffff800 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff800 0x200>;
+					interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+				};
+
+				pioD: gpio@fffffa00 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffffa00 0x200>;
+					interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					#gpio-lines = <22>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+				};
+			};
+
+			pmc: clock-controller@fffffc00 {
+				compatible = "microchip,sam9x60-pmc", "syscon";
+				reg = <0xfffffc00 0x200>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				#clock-cells = <2>;
+				clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+				clock-names = "td_slck", "md_slck", "main_xtal";
+			};
+
+			reset_controller: reset-controller@fffffe00 {
+				compatible = "microchip,sam9x60-rstc";
+				reg = <0xfffffe00 0x10>;
+				clocks = <&clk32k 0>;
+			};
+
+			shutdown_controller: poweroff@fffffe10 {
+				compatible = "microchip,sam9x60-shdwc";
+				reg = <0xfffffe10 0x10>;
+				clocks = <&clk32k 0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,wakeup-rtc-timer;
+				atmel,wakeup-rtt-timer;
+				status = "disabled";
+			};
+
+			rtt: rtc@fffffe20 {
+				compatible = "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
+				reg = <0xfffffe20 0x20>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+			};
+
+			pit: timer@fffffe40 {
+				compatible = "atmel,at91sam9260-pit";
+				reg = <0xfffffe40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
+			};
+
+			clk32k: clock-controller@fffffe50 {
+				compatible = "microchip,sam9x60-sckc";
+				reg = <0xfffffe50 0x4>;
+				clocks = <&slow_xtal>;
+				#clock-cells = <1>;
+			};
+
+			gpbr: syscon@fffffe60 {
+				compatible = "microchip,sam9x60-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+				reg = <0xfffffe60 0x10>;
+			};
+
+			rtc: rtc@fffffea8 {
+				compatible = "microchip,sam9x60-rtc", "atmel,at91sam9x5-rtc";
+				reg = <0xfffffea8 0x100>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+			};
+
+			watchdog: watchdog@ffffff80 {
+				compatible = "microchip,sam9x60-wdt";
+				reg = <0xffffff80 0x24>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sama5d2-pinfunc.h b/arch/arm/boot/dts/microchip/sama5d2-pinfunc.h
index 28a2e45752fe..28a2e45752fe 100644
--- a/arch/arm/boot/dts/sama5d2-pinfunc.h
+++ b/arch/arm/boot/dts/microchip/sama5d2-pinfunc.h
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/microchip/sama5d2.dtsi
index 565204816e34..5f8e297e19ed 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d2.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/iio/adc/at91-sama5d2_adc.h>
 
 / {
@@ -21,10 +22,6 @@
 	aliases {
 		serial0 = &uart1;
 		serial1 = &uart3;
-		tcb0 = &tcb0;
-		tcb1 = &tcb1;
-		i2s0 = &i2s0;
-		i2s1 = &i2s1;
 	};
 
 	cpus {
@@ -44,7 +41,7 @@
 		interrupts = <2 IRQ_TYPE_LEVEL_HIGH 0>;
 	};
 
-	etb {
+	etb@740000 {
 		compatible = "arm,coresight-etb10", "arm,primecell";
 		reg = <0x740000 0x1000>;
 
@@ -60,9 +57,9 @@
 		};
 	};
 
-	etm {
+	etm@73c000 {
 		compatible = "arm,coresight-etm3x", "arm,primecell";
-		reg = <0x73C000 0x1000>;
+		reg = <0x73c000 0x1000>;
 
 		clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 		clock-names = "apb_pclk";
@@ -76,7 +73,7 @@
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x20000000>;
 	};
@@ -98,6 +95,19 @@
 	ns_sram: sram@200000 {
 		compatible = "mmio-sram";
 		reg = <0x00200000 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00200000 0x20000>;
+	};
+
+	resistive_touch: resistive-touch {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc AT91_SAMA5D2_ADC_X_CHANNEL>,
+			      <&adc AT91_SAMA5D2_ADC_Y_CHANNEL>,
+			      <&adc AT91_SAMA5D2_ADC_P_CHANNEL>;
+		io-channel-names = "x", "y", "pressure";
+		touchscreen-min-pressure = <50000>;
+		status = "disabled";
 	};
 
 	ahb {
@@ -110,11 +120,13 @@
 			compatible = "mmio-sram";
 			no-memory-wc;
 			reg = <0x00100000 0x2400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x00100000 0x2400>;
+
 		};
 
 		usb0: gadget@300000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "atmel,sama5d3-udc";
 			reg = <0x00300000 0x100000
 			       0xfc02c000 0x400>;
@@ -122,124 +134,6 @@
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
 			clock-names = "pclk", "hclk";
 			status = "disabled";
-
-			ep@0 {
-				reg = <0>;
-				atmel,fifo-size = <64>;
-				atmel,nb-banks = <1>;
-			};
-
-			ep@1 {
-				reg = <1>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <3>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@2 {
-				reg = <2>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <3>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@3 {
-				reg = <3>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@4 {
-				reg = <4>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@5 {
-				reg = <5>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@6 {
-				reg = <6>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@7 {
-				reg = <7>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@8 {
-				reg = <8>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@9 {
-				reg = <9>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@10 {
-				reg = <10>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@11 {
-				reg = <11>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@12 {
-				reg = <12>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@13 {
-				reg = <13>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@14 {
-				reg = <14>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@15 {
-				reg = <15>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
 		};
 
 		usb1: ohci@400000 {
@@ -300,6 +194,8 @@
 			interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 31>, <&pmc PMC_TYPE_GCK 31>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
 			clock-names = "hclock", "multclk", "baseclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 31>;
+			assigned-clock-rates = <480000000>;
 			status = "disabled";
 		};
 
@@ -309,6 +205,8 @@
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_GCK 32>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
 			clock-names = "hclock", "multclk", "baseclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 32>;
+			assigned-clock-rates = <480000000>;
 			status = "disabled";
 		};
 
@@ -386,7 +284,7 @@
 				clock-names = "dma_clk";
 			};
 
-			pmc: pmc@f0014000 {
+			pmc: clock-controller@f0014000 {
 				compatible = "atmel,sama5d2-pmc", "syscon";
 				reg = <0xf0014000 0x160>;
 				interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -401,6 +299,7 @@
 				reg-names = "qspi_base", "qspi_mmap";
 				interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 52>;
+				clock-names = "pclk";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -412,12 +311,13 @@
 				reg-names = "qspi_base", "qspi_mmap";
 				interrupts = <53 IRQ_TYPE_LEVEL_HIGH 7>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 53>;
+				clock-names = "pclk";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
 			};
 
-			sha@f0028000 {
+			sha: crypto@f0028000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xf0028000 0x100>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -427,10 +327,9 @@
 				dma-names = "tx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "sha_clk";
-				status = "okay";
 			};
 
-			aes@f002c000 {
+			aes: crypto@f002c000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xf002c000 0x100>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -443,7 +342,6 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				clock-names = "aes_clk";
-				status = "okay";
 			};
 
 			spi0: spi@f8000000 {
@@ -484,34 +382,32 @@
 			macb0: ethernet@f8008000 {
 				compatible = "atmel,sama5d2-gem";
 				reg = <0xf8008000 0x1000>;
-				interrupts = <5  IRQ_TYPE_LEVEL_HIGH 3		/* Queue 0 */
-					      66 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 1 */
-					      67 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 2 */
-				#address-cells = <1>;
-				#size-cells = <0>;
+				interrupts = <5  IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 0 */
+					     <66 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 1 */
+					     <67 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 2 */
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>, <&pmc PMC_TYPE_PERIPHERAL 5>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
 			};
 
 			tcb0: timer@f800c000 {
-				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				compatible = "atmel,sama5d2-tcb", "simple-mfd", "syscon";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xf800c000 0x100>;
 				interrupts = <35 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&clk32k>;
-				clock-names = "t0_clk", "slow_clk";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_GCK 35>, <&clk32k>;
+				clock-names = "t0_clk", "gclk", "slow_clk";
 			};
 
 			tcb1: timer@f8010000 {
-				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				compatible = "atmel,sama5d2-tcb", "simple-mfd", "syscon";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xf8010000 0x100>;
 				interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&pmc PMC_TYPE_PERIPHERAL 36>, <&clk32k>;
-				clock-names = "t0_clk", "slow_clk";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 36>, <&pmc PMC_TYPE_GCK 36>, <&clk32k>;
+				clock-names = "t0_clk", "gclk", "slow_clk";
 			};
 
 			hsmc: hsmc@f8014000 {
@@ -526,7 +422,7 @@
 				pmecc: ecc-engine@f8014070 {
 					compatible = "atmel,sama5d2-pmecc";
 					reg = <0xf8014070 0x490>,
-					      <0xf8014500 0x100>;
+					      <0xf8014500 0x200>;
 				};
 			};
 
@@ -546,6 +442,7 @@
 			uart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -562,6 +459,7 @@
 			uart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -578,6 +476,7 @@
 			uart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -615,6 +514,7 @@
 				interrupts = <38 IRQ_TYPE_LEVEL_HIGH 7>;
 				#pwm-cells = <3>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				status = "disabled";
 			};
 
 			sfr: sfr@f8030000 {
@@ -630,6 +530,67 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8034000 0x800>;
 				status = "disabled";
+
+				uart5: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+					clock-names = "usart";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi2: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c2: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx1: flexcom@f8038000 {
@@ -640,6 +601,67 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xf8038000 0x800>;
 				status = "disabled";
+
+				uart6: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+					clock-names = "usart";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi3: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c3: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			securam: sram@f8044000 {
@@ -648,16 +670,17 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 51>;
 				#address-cells = <1>;
 				#size-cells = <1>;
+				no-memory-wc;
 				ranges = <0 0xf8044000 0x1420>;
 			};
 
-			reset_controller: rstc@f8048000 {
+			reset_controller: reset-controller@f8048000 {
 				compatible = "atmel,sama5d3-rstc";
 				reg = <0xf8048000 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shdwc@f8048010 {
+			shutdown_controller: poweroff@f8048010 {
 				compatible = "atmel,sama5d2-shdwc";
 				reg = <0xf8048010 0x10>;
 				clocks = <&clk32k>;
@@ -681,16 +704,15 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@f8048050 {
+			clk32k: clock-controller@f8048050 {
 				compatible = "atmel,sama5d4-sckc";
 				reg = <0xf8048050 0x4>;
-
 				clocks = <&slow_xtal>;
 				#clock-cells = <0>;
 			};
 
 			rtc: rtc@f80480b0 {
-				compatible = "atmel,at91rm9200-rtc";
+				compatible = "atmel,sama5d2-rtc";
 				reg = <0xf80480b0 0x30>;
 				interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>;
 				clocks = <&clk32k>;
@@ -716,7 +738,7 @@
 
 			can0: can@f8054000 {
 				compatible = "bosch,m_can";
-				reg = <0xf8054000 0x4000>, <0x210000 0x4000>;
+				reg = <0xf8054000 0x4000>, <0x210000 0x1c00>;
 				reg-names = "m_can", "message_ram";
 				interrupts = <56 IRQ_TYPE_LEVEL_HIGH 7>,
 					     <64 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -752,6 +774,7 @@
 			uart3: serial@fc008000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc008000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -768,6 +791,7 @@
 			uart4: serial@fc00c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc00c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
 					 AT91_XDMAC_DT_PERID(43))>,
@@ -789,6 +813,67 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xfc010000 0x800>;
 				status = "disabled";
+
+				uart7: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
+					clock-names = "usart";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi4: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c4: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx3: flexcom@fc014000 {
@@ -799,6 +884,68 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xfc014000 0x800>;
 				status = "disabled";
+
+				uart8: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+					clock-names = "usart";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi5: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c5: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
 			};
 
 			flx4: flexcom@fc018000 {
@@ -809,6 +956,67 @@
 				#size-cells = <1>;
 				ranges = <0x0 0xfc018000 0x800>;
 				status = "disabled";
+
+				uart9: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+					clock-names = "usart";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi6: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c6: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			trng@fc01c000 {
@@ -860,16 +1068,6 @@
 				status = "disabled";
 			};
 
-			resistive_touch: resistive-touch {
-				compatible = "resistive-adc-touch";
-				io-channels = <&adc AT91_SAMA5D2_ADC_X_CHANNEL>,
-					      <&adc AT91_SAMA5D2_ADC_Y_CHANNEL>,
-					      <&adc AT91_SAMA5D2_ADC_P_CHANNEL>;
-				io-channel-names = "x", "y", "pressure";
-				touchscreen-min-pressure = <50000>;
-				status = "disabled";
-			};
-
 			pioA: pinctrl@fc038000 {
 				compatible = "atmel,sama5d2-pinctrl";
 				reg = <0xfc038000 0x600>;
@@ -884,12 +1082,15 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
 			};
 
-			secumod@fc040000 {
+			pioBU: secumod@fc040000 {
 				compatible = "atmel,sama5d2-secumod", "syscon";
 				reg = <0xfc040000 0x100>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
 			};
 
-			tdes@fc044000 {
+			tdes: crypto@fc044000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xfc044000 0x100>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -902,7 +1103,6 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
 				clock-names = "tdes_clk";
-				status = "okay";
 			};
 
 			classd: classd@fc048000 {
@@ -932,13 +1132,13 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 55>, <&pmc PMC_TYPE_GCK 55>;
 				clock-names = "pclk", "gclk";
 				assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S1_MUX>;
-				assigned-parrents = <&pmc PMC_TYPE_GCK 55>;
+				assigned-clock-parents = <&pmc PMC_TYPE_GCK 55>;
 				status = "disabled";
 			};
 
 			can1: can@fc050000 {
 				compatible = "bosch,m_can";
-				reg = <0xfc050000 0x4000>, <0x210000 0x4000>;
+				reg = <0xfc050000 0x4000>, <0x210000 0x3800>;
 				reg-names = "m_can", "message_ram";
 				interrupts = <57 IRQ_TYPE_LEVEL_HIGH 7>,
 					     <65 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -948,7 +1148,7 @@
 				assigned-clocks = <&pmc PMC_TYPE_GCK 57>;
 				assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>;
 				assigned-clock-rates = <40000000>;
-				bosch,mram-cfg = <0x1100 0 0 64 0 0 32 32>;
+				bosch,mram-cfg = <0x1c00 0 0 64 0 0 32 32>;
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/microchip/sama5d29.dtsi b/arch/arm/boot/dts/microchip/sama5d29.dtsi
new file mode 100644
index 000000000000..17991c28a256
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sama5d29.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sama5d29.dtsi - Device Tree Include file for SAMA5D29 SoC of the SAMA5D2
+ * family.
+ *
+ *  Copyright (C) 2021 Microchip Technology, Inc. and its subsidiaries
+ *
+ *  Author: Hari Prasath <Hari.PrasathGE@microchip.com>
+ *
+ */
+
+#include "sama5d2.dtsi"
+
+&macb0 {
+	compatible = "atmel,sama5d29-gem";
+};
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/microchip/sama5d3.dtsi
index f770aace0efd..d4fc0c1dfc10 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -55,7 +56,7 @@
 		interrupts = <46 IRQ_TYPE_LEVEL_HIGH 0>;
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x8000000>;
 	};
@@ -73,7 +74,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -83,6 +84,9 @@
 	sram: sram@300000 {
 		compatible = "mmio-sram";
 		reg = <0x00300000 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x20000>;
 	};
 
 	ahb {
@@ -108,7 +112,7 @@
 				status = "disabled";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&mci0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
 				clock-names = "mci_clk";
 			};
 
@@ -123,7 +127,7 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0>;
-				clocks = <&spi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 24>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
@@ -137,7 +141,7 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
-				clocks = <&ssc0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
@@ -148,7 +152,7 @@
 				#size-cells = <0>;
 				reg = <0xf0010000 0x100>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tcb0_clk>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&clk32k>;
 				clock-names = "t0_clk", "slow_clk";
 			};
 
@@ -159,11 +163,14 @@
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(7)>,
 				       <&dma0 2 AT91_DMA_CFG_PER_ID(8)>;
 				dma-names = "tx", "rx";
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c0>;
+				pinctrl-1 = <&pinctrl_i2c0_gpio>;
+				sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&twi0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
 				status = "disabled";
 			};
 
@@ -174,24 +181,28 @@
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(9)>,
 				       <&dma0 2 AT91_DMA_CFG_PER_ID(10)>;
 				dma-names = "tx", "rx";
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c1>;
+				pinctrl-1 = <&pinctrl_i2c1_gpio>;
+				sda-gpios = <&pioC 26 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioC 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&twi1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
 				status = "disabled";
 			};
 
 			usart0: serial@f001c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf001c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
 				       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
-				clocks = <&usart0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -199,13 +210,14 @@
 			usart1: serial@f0020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(5)>,
 				       <&dma0 2 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
-				clocks = <&usart1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -213,10 +225,11 @@
 			uart0: serial@f0024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
-				clocks = <&uart0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -226,7 +239,7 @@
 				reg = <0xf002c000 0x300>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 4>;
 				#pwm-cells = <3>;
-				clocks = <&pwm_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
 				status = "disabled";
 			};
 
@@ -236,7 +249,7 @@
 				interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_isi_data_0_7>;
-				clocks = <&isi_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
 				clock-names = "isi_clk";
 				status = "disabled";
 				port {
@@ -261,7 +274,7 @@
 				status = "disabled";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&mci1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
 				clock-names = "mci_clk";
 			};
 
@@ -276,7 +289,7 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi1>;
-				clocks = <&spi1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 25>;
 				clock-names = "spi_clk";
 				status = "disabled";
 			};
@@ -290,15 +303,13 @@
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
-				clocks = <&ssc1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
 				clock-names = "pclk";
 				status = "disabled";
 			};
 
 			adc0: adc@f8018000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "atmel,at91sam9x5-adc";
+				compatible = "atmel,sama5d3-adc";
 				reg = <0xf8018000 0x100>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
@@ -317,37 +328,15 @@
 					&pinctrl_adc0_ad10
 					&pinctrl_adc0_ad11
 					>;
-				clocks = <&adc_clk>,
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 29>,
 					 <&adc_op_clk>;
 				clock-names = "adc_clk", "adc_op_clk";
 				atmel,adc-channels-used = <0xfff>;
 				atmel,adc-startup-time = <40>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-vref = <3000>;
-				atmel,adc-res = <10 12>;
 				atmel,adc-sample-hold-time = <11>;
-				atmel,adc-res-names = "lowres", "highres";
 				status = "disabled";
-
-				trigger0 {
-					trigger-name = "external-rising";
-					trigger-value = <0x1>;
-					trigger-external;
-				};
-				trigger1 {
-					trigger-name = "external-falling";
-					trigger-value = <0x2>;
-					trigger-external;
-				};
-				trigger2 {
-					trigger-name = "external-any";
-					trigger-value = <0x3>;
-					trigger-external;
-				};
-				trigger3 {
-					trigger-name = "continuous";
-					trigger-value = <0x6>;
-				};
 			};
 
 			i2c2: i2c@f801c000 {
@@ -357,24 +346,28 @@
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(11)>,
 				       <&dma1 2 AT91_DMA_CFG_PER_ID(12)>;
 				dma-names = "tx", "rx";
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c2>;
+				pinctrl-1 = <&pinctrl_i2c2_gpio>;
+				sda-gpios = <&pioA 18 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				clocks = <&twi2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
 				status = "disabled";
 			};
 
 			usart2: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(7)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(8) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
-				clocks = <&usart2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -382,46 +375,47 @@
 			usart3: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(9)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(10) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
-				clocks = <&usart3_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
 				clock-names = "usart";
 				status = "disabled";
 			};
 
-			sha@f8034000 {
+			sha: crypto@f8034000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xf8034000 0x100>;
 				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 0>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(17)>;
 				dma-names = "tx";
-				clocks = <&sha_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
 				clock-names = "sha_clk";
 			};
 
-			aes@f8038000 {
+			aes: crypto@f8038000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xf8038000 0x100>;
 				interrupts = <43 IRQ_TYPE_LEVEL_HIGH 0>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(18)>,
 				       <&dma1 2 AT91_DMA_CFG_PER_ID(19)>;
 				dma-names = "tx", "rx";
-				clocks = <&aes_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
 				clock-names = "aes_clk";
 			};
 
-			tdes@f803c000 {
+			tdes: crypto@f803c000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xf803c000 0x100>;
 				interrupts = <44 IRQ_TYPE_LEVEL_HIGH 0>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(20)>,
 				       <&dma1 2 AT91_DMA_CFG_PER_ID(21)>;
 				dma-names = "tx", "rx";
-				clocks = <&tdes_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
 				clock-names = "tdes_clk";
 			};
 
@@ -429,14 +423,14 @@
 				compatible = "atmel,at91sam9g45-trng";
 				reg = <0xf8040000 0x100>;
 				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&trng_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
 			};
 
 			hsmc: hsmc@ffffc000 {
 				compatible = "atmel,sama5d3-smc", "syscon", "simple-mfd";
 				reg = <0xffffc000 0x1000>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>;
-				clocks = <&hsmc_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges;
@@ -453,7 +447,7 @@
 				reg = <0xffffe600 0x200>;
 				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0>;
 				#dma-cells = <2>;
-				clocks = <&dma0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 30>;
 				clock-names = "dma_clk";
 			};
 
@@ -462,27 +456,28 @@
 				reg = <0xffffe800 0x200>;
 				interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
 				#dma-cells = <2>;
-				clocks = <&dma1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 31>;
 				clock-names = "dma_clk";
 			};
 
 			ramc0: ramc@ffffea00 {
 				compatible = "atmel,sama5d3-ddramc";
 				reg = <0xffffea00 0x200>;
-				clocks = <&ddrck>, <&mpddr_clk>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 49>;
 				clock-names = "ddrck", "mpddr";
 			};
 
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(14) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
-				clocks = <&dbgu_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -639,6 +634,12 @@
 							<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PA30 periph A TWD0 pin, conflicts with URXD1, ISI_VSYNC */
 							 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA31 periph A TWCK0 pin, conflicts with UTXD1, ISI_HSYNC */
 					};
+
+					pinctrl_i2c0_gpio: i2c0-gpio {
+						atmel,pins =
+							<AT91_PIOA 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOA 31 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 
 				i2c1 {
@@ -647,6 +648,12 @@
 							<AT91_PIOC 26 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PC26 periph B TWD1 pin, conflicts with SPI1_NPCS1, ISI_D11 */
 							 AT91_PIOC 27 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC27 periph B TWCK1 pin, conflicts with SPI1_NPCS2, ISI_D10 */
 					};
+
+					pinctrl_i2c1_gpio: i2c1-gpio {
+						atmel,pins =
+							<AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOC 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 
 				i2c2 {
@@ -655,6 +662,12 @@
 							<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE	/* TWD2 pin, conflicts with LCDDAT18, ISI_D2 */
 							 AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TWCK2 pin, conflicts with LCDDAT19, ISI_D3 */
 					};
+
+					pinctrl_i2c2_gpio: i2c2-gpio {
+						atmel,pins =
+							<AT91_PIOA 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOA 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 
 				isi {
@@ -703,7 +716,7 @@
 						atmel,pins =
 							<AT91_PIOD 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD5 periph A MCI0_DA4 with pullup, conflicts with TIOA0, PWMH2 */
 							 AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD6 periph A MCI0_DA5 with pullup, conflicts with TIOB0, PWML2 */
-							 AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD7 periph A MCI0_DA6 with pullup, conlicts with TCLK0, PWMH3 */
+							 AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD7 periph A MCI0_DA6 with pullup, conflicts with TCLK0, PWMH3 */
 							 AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;	/* PD8 periph A MCI0_DA7 with pullup, conflicts with PWML3 */
 					};
 				};
@@ -940,7 +953,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioA_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
 				};
 
 				pioB: gpio@fffff400 {
@@ -951,7 +964,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioB_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
 				};
 
 				pioC: gpio@fffff600 {
@@ -962,7 +975,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioC_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
 				};
 
 				pioD: gpio@fffff800 {
@@ -973,7 +986,7 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioD_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				};
 
 				pioE: gpio@fffffa00 {
@@ -984,370 +997,26 @@
 					gpio-controller;
 					interrupt-controller;
 					#interrupt-cells = <2>;
-					clocks = <&pioE_clk>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,sama5d3-pmc", "syscon";
 				reg = <0xfffffc00 0x120>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				#interrupt-cells = <1>;
-
-				main_rc_osc: main_rc_osc {
-					compatible = "atmel,at91sam9x5-clk-main-rc-osc";
-					#clock-cells = <0>;
-					interrupt-parent = <&pmc>;
-					interrupts = <AT91_PMC_MOSCRCS>;
-					clock-frequency = <12000000>;
-					clock-accuracy = <50000000>;
-				};
-
-				main_osc: main_osc {
-					compatible = "atmel,at91rm9200-clk-main-osc";
-					#clock-cells = <0>;
-					interrupt-parent = <&pmc>;
-					interrupts = <AT91_PMC_MOSCS>;
-					clocks = <&main_xtal>;
-				};
-
-				main: mainck {
-					compatible = "atmel,at91sam9x5-clk-main";
-					#clock-cells = <0>;
-					interrupt-parent = <&pmc>;
-					interrupts = <AT91_PMC_MOSCSELS>;
-					clocks = <&main_rc_osc &main_osc>;
-				};
-
-				plla: pllack {
-					compatible = "atmel,sama5d3-clk-pll";
-					#clock-cells = <0>;
-					interrupt-parent = <&pmc>;
-					interrupts = <AT91_PMC_LOCKA>;
-					clocks = <&main>;
-					reg = <0>;
-					atmel,clk-input-range = <8000000 50000000>;
-					#atmel,pll-clk-output-range-cells = <4>;
-					atmel,pll-clk-output-ranges = <400000000 1000000000 0 0>;
-				};
-
-				plladiv: plladivck {
-					compatible = "atmel,at91sam9x5-clk-plldiv";
-					#clock-cells = <0>;
-					clocks = <&plla>;
-				};
-
-				utmi: utmick {
-					compatible = "atmel,at91sam9x5-clk-utmi";
-					#clock-cells = <0>;
-					interrupt-parent = <&pmc>;
-					interrupts = <AT91_PMC_LOCKU>;
-					clocks = <&main>;
-				};
-
-				mck: masterck {
-					compatible = "atmel,at91sam9x5-clk-master";
-					#clock-cells = <0>;
-					interrupt-parent = <&pmc>;
-					interrupts = <AT91_PMC_MCKRDY>;
-					clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
-					atmel,clk-output-range = <0 166000000>;
-					atmel,clk-divisors = <1 2 4 3>;
-				};
-
-				usb: usbck {
-					compatible = "atmel,at91sam9x5-clk-usb";
-					#clock-cells = <0>;
-					clocks = <&plladiv>, <&utmi>;
-				};
-
-				prog: progck {
-					compatible = "atmel,at91sam9x5-clk-programmable";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					interrupt-parent = <&pmc>;
-					clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
-
-					prog0: prog0 {
-						#clock-cells = <0>;
-						reg = <0>;
-						interrupts = <AT91_PMC_PCKRDY(0)>;
-					};
-
-					prog1: prog1 {
-						#clock-cells = <0>;
-						reg = <1>;
-						interrupts = <AT91_PMC_PCKRDY(1)>;
-					};
-
-					prog2: prog2 {
-						#clock-cells = <0>;
-						reg = <2>;
-						interrupts = <AT91_PMC_PCKRDY(2)>;
-					};
-				};
-
-				smd: smdclk {
-					compatible = "atmel,at91sam9x5-clk-smd";
-					#clock-cells = <0>;
-					clocks = <&plladiv>, <&utmi>;
-				};
-
-				systemck {
-					compatible = "atmel,at91rm9200-clk-system";
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					ddrck: ddrck {
-						#clock-cells = <0>;
-						reg = <2>;
-						clocks = <&mck>;
-					};
-
-					smdck: smdck {
-						#clock-cells = <0>;
-						reg = <4>;
-						clocks = <&smd>;
-					};
-
-					uhpck: uhpck {
-						#clock-cells = <0>;
-						reg = <6>;
-						clocks = <&usb>;
-					};
-
-					udpck: udpck {
-						#clock-cells = <0>;
-						reg = <7>;
-						clocks = <&usb>;
-					};
-
-					pck0: pck0 {
-						#clock-cells = <0>;
-						reg = <8>;
-						clocks = <&prog0>;
-					};
-
-					pck1: pck1 {
-						#clock-cells = <0>;
-						reg = <9>;
-						clocks = <&prog1>;
-					};
-
-					pck2: pck2 {
-						#clock-cells = <0>;
-						reg = <10>;
-						clocks = <&prog2>;
-					};
-				};
-
-				periphck {
-					compatible = "atmel,at91sam9x5-clk-peripheral";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					clocks = <&mck>;
-
-					dbgu_clk: dbgu_clk {
-						#clock-cells = <0>;
-						reg = <2>;
-					};
-
-					hsmc_clk: hsmc_clk {
-						#clock-cells = <0>;
-						reg = <5>;
-					};
-
-					pioA_clk: pioA_clk {
-						#clock-cells = <0>;
-						reg = <6>;
-					};
-
-					pioB_clk: pioB_clk {
-						#clock-cells = <0>;
-						reg = <7>;
-					};
-
-					pioC_clk: pioC_clk {
-						#clock-cells = <0>;
-						reg = <8>;
-					};
-
-					pioD_clk: pioD_clk {
-						#clock-cells = <0>;
-						reg = <9>;
-					};
-
-					pioE_clk: pioE_clk {
-						#clock-cells = <0>;
-						reg = <10>;
-					};
-
-					usart0_clk: usart0_clk {
-						#clock-cells = <0>;
-						reg = <12>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					usart1_clk: usart1_clk {
-						#clock-cells = <0>;
-						reg = <13>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					usart2_clk: usart2_clk {
-						#clock-cells = <0>;
-						reg = <14>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					usart3_clk: usart3_clk {
-						#clock-cells = <0>;
-						reg = <15>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					uart0_clk: uart0_clk {
-						#clock-cells = <0>;
-						reg = <16>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					twi0_clk: twi0_clk {
-						reg = <18>;
-						#clock-cells = <0>;
-						atmel,clk-output-range = <0 16625000>;
-					};
-
-					twi1_clk: twi1_clk {
-						#clock-cells = <0>;
-						reg = <19>;
-						atmel,clk-output-range = <0 16625000>;
-					};
-
-					twi2_clk: twi2_clk {
-						#clock-cells = <0>;
-						reg = <20>;
-						atmel,clk-output-range = <0 16625000>;
-					};
-
-					mci0_clk: mci0_clk {
-						#clock-cells = <0>;
-						reg = <21>;
-					};
-
-					mci1_clk: mci1_clk {
-						#clock-cells = <0>;
-						reg = <22>;
-					};
-
-					spi0_clk: spi0_clk {
-						#clock-cells = <0>;
-						reg = <24>;
-						atmel,clk-output-range = <0 133000000>;
-					};
-
-					spi1_clk: spi1_clk {
-						#clock-cells = <0>;
-						reg = <25>;
-						atmel,clk-output-range = <0 133000000>;
-					};
-
-					tcb0_clk: tcb0_clk {
-						#clock-cells = <0>;
-						reg = <26>;
-						atmel,clk-output-range = <0 133000000>;
-					};
-
-					pwm_clk: pwm_clk {
-						#clock-cells = <0>;
-						reg = <28>;
-					};
-
-					adc_clk: adc_clk {
-						#clock-cells = <0>;
-						reg = <29>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					dma0_clk: dma0_clk {
-						#clock-cells = <0>;
-						reg = <30>;
-					};
-
-					dma1_clk: dma1_clk {
-						#clock-cells = <0>;
-						reg = <31>;
-					};
-
-					uhphs_clk: uhphs_clk {
-						#clock-cells = <0>;
-						reg = <32>;
-					};
-
-					udphs_clk: udphs_clk {
-						#clock-cells = <0>;
-						reg = <33>;
-					};
-
-					isi_clk: isi_clk {
-						#clock-cells = <0>;
-						reg = <37>;
-					};
-
-					ssc0_clk: ssc0_clk {
-						#clock-cells = <0>;
-						reg = <38>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					ssc1_clk: ssc1_clk {
-						#clock-cells = <0>;
-						reg = <39>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					sha_clk: sha_clk {
-						#clock-cells = <0>;
-						reg = <42>;
-					};
-
-					aes_clk: aes_clk {
-						#clock-cells = <0>;
-						reg = <43>;
-					};
-
-					tdes_clk: tdes_clk {
-						#clock-cells = <0>;
-						reg = <44>;
-					};
-
-					trng_clk: trng_clk {
-						#clock-cells = <0>;
-						reg = <45>;
-					};
-
-					fuse_clk: fuse_clk {
-						#clock-cells = <0>;
-						reg = <48>;
-					};
-
-					mpddr_clk: mpddr_clk {
-						#clock-cells = <0>;
-						reg = <49>;
-					};
-				};
+				#clock-cells = <2>;
+				clocks = <&clk32k>, <&main_xtal>;
+				clock-names = "slow_clk", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shutdown-controller@fffffe10 {
+			shutdown_controller: poweroff@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
@@ -1357,7 +1026,7 @@
 				compatible = "atmel,at91sam9260-pit";
 				reg = <0xfffffe30 0xf>;
 				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>;
-				clocks = <&mck>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			};
 
 			watchdog: watchdog@fffffe40 {
@@ -1371,7 +1040,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fffffe50 {
+			clk32k: clock-controller@fffffe50 {
 				compatible = "atmel,sama5d3-sckc";
 				reg = <0xfffffe50 0x4>;
 				clocks = <&slow_xtal>;
@@ -1390,130 +1059,26 @@
 			compatible = "mmio-sram";
 			no-memory-wc;
 			reg = <0x200000 0x2400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x200000 0x2400>;
 		};
 
 		usb0: gadget@500000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "atmel,sama5d3-udc";
 			reg = <0x00500000 0x100000
 			       0xf8030000 0x4000>;
 			interrupts = <33 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&udphs_clk>, <&utmi>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 33>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
 			clock-names = "pclk", "hclk";
 			status = "disabled";
-
-			ep@0 {
-				reg = <0>;
-				atmel,fifo-size = <64>;
-				atmel,nb-banks = <1>;
-			};
-
-			ep@1 {
-				reg = <1>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <3>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@2 {
-				reg = <2>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <3>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@3 {
-				reg = <3>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-			};
-
-			ep@4 {
-				reg = <4>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-			};
-
-			ep@5 {
-				reg = <5>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-			};
-
-			ep@6 {
-				reg = <6>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-			};
-
-			ep@7 {
-				reg = <7>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-			};
-
-			ep@8 {
-				reg = <8>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@9 {
-				reg = <9>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@10 {
-				reg = <10>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@11 {
-				reg = <11>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@12 {
-				reg = <12>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@13 {
-				reg = <13>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@14 {
-				reg = <14>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
-
-			ep@15 {
-				reg = <15>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-			};
 		};
 
 		usb1: ohci@600000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_SYSTEM 6>;
 			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
@@ -1522,7 +1087,7 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&utmi>, <&uhphs_clk>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 32>;
 			clock-names = "usb_clk", "ehci_clk";
 			status = "disabled";
 		};
@@ -1538,7 +1103,7 @@
 				  0x1 0x0 0x40000000 0x10000000
 				  0x2 0x0 0x50000000 0x10000000
 				  0x3 0x0 0x60000000 0x10000000>;
-			clocks = <&mck>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			status = "disabled";
 
 			nand_controller: nand-controller {
diff --git a/arch/arm/boot/dts/sama5d31.dtsi b/arch/arm/boot/dts/microchip/sama5d31.dtsi
index cbe8f275ecc4..cbe8f275ecc4 100644
--- a/arch/arm/boot/dts/sama5d31.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d31.dtsi
diff --git a/arch/arm/boot/dts/sama5d31ek.dts b/arch/arm/boot/dts/microchip/sama5d31ek.dts
index 10fc80d6d30d..1f2dfb3127ab 100644
--- a/arch/arm/boot/dts/sama5d31ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d31ek.dts
@@ -40,7 +40,7 @@
 	};
 
 	leds {
-		d3 {
+		led-d3 {
 			label = "d3";
 			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sama5d33.dtsi b/arch/arm/boot/dts/microchip/sama5d33.dtsi
index 146fd59acea5..146fd59acea5 100644
--- a/arch/arm/boot/dts/sama5d33.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d33.dtsi
diff --git a/arch/arm/boot/dts/sama5d33ek.dts b/arch/arm/boot/dts/microchip/sama5d33ek.dts
index 7d4ae1682933..7d4ae1682933 100644
--- a/arch/arm/boot/dts/sama5d33ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d33ek.dts
diff --git a/arch/arm/boot/dts/sama5d34.dtsi b/arch/arm/boot/dts/microchip/sama5d34.dtsi
index 132918c889a0..132918c889a0 100644
--- a/arch/arm/boot/dts/sama5d34.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d34.dtsi
diff --git a/arch/arm/boot/dts/sama5d34ek.dts b/arch/arm/boot/dts/microchip/sama5d34ek.dts
index 2335bf906f69..bffd61397cb5 100644
--- a/arch/arm/boot/dts/sama5d34ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d34ek.dts
@@ -50,7 +50,7 @@
 	};
 
 	leds {
-		d3 {
+		led-d3 {
 			label = "d3";
 			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sama5d35.dtsi b/arch/arm/boot/dts/microchip/sama5d35.dtsi
index b2ccfa77c4be..b2ccfa77c4be 100644
--- a/arch/arm/boot/dts/sama5d35.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d35.dtsi
diff --git a/arch/arm/boot/dts/sama5d35ek.dts b/arch/arm/boot/dts/microchip/sama5d35ek.dts
index 8edfcebb1df0..8edfcebb1df0 100644
--- a/arch/arm/boot/dts/sama5d35ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d35ek.dts
diff --git a/arch/arm/boot/dts/sama5d36.dtsi b/arch/arm/boot/dts/microchip/sama5d36.dtsi
index 5d88f9967138..5d88f9967138 100644
--- a/arch/arm/boot/dts/sama5d36.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d36.dtsi
diff --git a/arch/arm/boot/dts/sama5d36ek.dts b/arch/arm/boot/dts/microchip/sama5d36ek.dts
index 26950f9284c2..26950f9284c2 100644
--- a/arch/arm/boot/dts/sama5d36ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d36ek.dts
diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/microchip/sama5d36ek_cmp.dts
index 66695b9a3e77..66695b9a3e77 100644
--- a/arch/arm/boot/dts/sama5d36ek_cmp.dts
+++ b/arch/arm/boot/dts/microchip/sama5d36ek_cmp.dts
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/microchip/sama5d3_can.dtsi
index cf06a018ed0f..9ac29bf3f933 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_can.dtsi
@@ -31,29 +31,13 @@
 
 			};
 
-			pmc: pmc@fffffc00 {
-				periphck {
-					can0_clk: can0_clk {
-						#clock-cells = <0>;
-						reg = <40>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					can1_clk: can1_clk {
-						#clock-cells = <0>;
-						reg = <41>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-				};
-			};
-
 			can0: can@f000c000 {
 				compatible = "atmel,at91sam9x5-can";
 				reg = <0xf000c000 0x300>;
 				interrupts = <40 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_can0_rx_tx>;
-				clocks = <&can0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
 				clock-names = "can_clk";
 				status = "disabled";
 			};
@@ -64,7 +48,7 @@
 				interrupts = <41 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_can1_rx_tx>;
-				clocks = <&can1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
 				clock-names = "can_clk";
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/sama5d3_emac.dtsi b/arch/arm/boot/dts/microchip/sama5d3_emac.dtsi
index 9aef414bcd2e..5d7ce13de8cc 100644
--- a/arch/arm/boot/dts/sama5d3_emac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_emac.dtsi
@@ -30,13 +30,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
-				periphck {
-					macb1_clk: macb1_clk {
-						#clock-cells = <0>;
-						reg = <35>;
-					};
-				};
+			pmc: clock-controller@fffffc00 {
 			};
 
 			macb1: ethernet@f802c000 {
@@ -45,7 +39,7 @@
 				interrupts = <35 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb1_rmii>;
-				clocks = <&macb1_clk>, <&macb1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_PERIPHERAL 35>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/sama5d3_gmac.dtsi b/arch/arm/boot/dts/microchip/sama5d3_gmac.dtsi
index 3667765a138b..884df7a54dbb 100644
--- a/arch/arm/boot/dts/sama5d3_gmac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_gmac.dtsi
@@ -63,22 +63,13 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
-				periphck {
-					macb0_clk: macb0_clk {
-						#clock-cells = <0>;
-						reg = <34>;
-					};
-				};
-			};
-
 			macb0: ethernet@f0028000 {
 				compatible = "atmel,sama5d3-gem";
 				reg = <0xf0028000 0x100>;
 				interrupts = <34 IRQ_TYPE_LEVEL_HIGH 3>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_data_rgmii &pinctrl_macb0_signal_rgmii>;
-				clocks = <&macb0_clk>, <&macb0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_PERIPHERAL 34>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/sama5d3_lcd.dtsi b/arch/arm/boot/dts/microchip/sama5d3_lcd.dtsi
index 2cf046cd4e99..308d2fc276d6 100644
--- a/arch/arm/boot/dts/sama5d3_lcd.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_lcd.dtsi
@@ -16,7 +16,7 @@
 				compatible = "atmel,sama5d3-hlcdc";
 				reg = <0xf0030000 0x2000>;
 				interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 36>, <&pmc PMC_TYPE_SYSTEM 3>, <&clk32k>;
 				clock-names = "periph_clk","sys_clk", "slow_clk";
 				status = "disabled";
 
@@ -192,23 +192,6 @@
 					};
 				};
 			};
-
-			pmc: pmc@fffffc00 {
-				periphck {
-					lcdc_clk: lcdc_clk {
-						#clock-cells = <0>;
-						reg = <36>;
-					};
-				};
-
-				systemck {
-					lcdck: lcdck {
-						#clock-cells = <0>;
-						reg = <3>;
-						clocks = <&mck>;
-					};
-				};
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/microchip/sama5d3_mci2.dtsi
index 3c83c1c36ac8..7141ee97ec3e 100644
--- a/arch/arm/boot/dts/sama5d3_mci2.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_mci2.dtsi
@@ -30,15 +30,6 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
-				periphck {
-					mci2_clk: mci2_clk {
-						#clock-cells = <0>;
-						reg = <23>;
-					};
-				};
-			};
-
 			mmc2: mmc@f8004000 {
 				compatible = "atmel,hsmci";
 				reg = <0xf8004000 0x600>;
@@ -47,7 +38,7 @@
 				dma-names = "rxtx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_mmc2_clk_cmd_dat0 &pinctrl_mmc2_dat1_3>;
-				clocks = <&mci2_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
 				clock-names = "mci_clk";
 				status = "disabled";
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/microchip/sama5d3_tcb1.dtsi
index 1584035daf51..2b18c5c2cc03 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_tcb1.dtsi
@@ -17,22 +17,13 @@
 
 	ahb {
 		apb {
-			pmc: pmc@fffffc00 {
-				periphck {
-					tcb1_clk: tcb1_clk {
-						#clock-cells = <0>;
-						reg = <27>;
-					};
-				};
-			};
-
 			tcb1: timer@f8014000 {
 				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xf8014000 0x100>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&tcb1_clk>, <&clk32k>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 27>, <&clk32k>;
 				clock-names = "t0_clk", "slow_clk";
 			};
 		};
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/microchip/sama5d3_uart.dtsi
index 4316bdbdc25d..44d1173f2ffb 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_uart.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	aliases {
@@ -36,29 +37,14 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
-				periphck {
-					uart0_clk: uart0_clk {
-						#clock-cells = <0>;
-						reg = <16>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-
-					uart1_clk: uart1_clk {
-						#clock-cells = <0>;
-						reg = <17>;
-						atmel,clk-output-range = <0 66000000>;
-					};
-				};
-			};
-
 			uart0: serial@f0024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
-				clocks = <&uart0_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
 				clock-names = "usart";
 				status = "disabled";
 			};
@@ -66,10 +52,11 @@
 			uart1: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
-				clocks = <&uart1_clk>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>;
 				clock-names = "usart";
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/microchip/sama5d3xcm.dtsi
index 65566e4b78d8..7d1d7859edb4 100644
--- a/arch/arm/boot/dts/sama5d3xcm.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xcm.dtsi
@@ -14,7 +14,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x20000000>;
 	};
 
@@ -130,7 +130,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioE 25 GPIO_ACTIVE_LOW>;	/* PE25, conflicts with A25, RXD2 */
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/microchip/sama5d3xcm_cmp.dtsi
index 9d2563602cbe..830a0954ba1b 100644
--- a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xcm_cmp.dtsi
@@ -12,7 +12,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x20000000>;
 	};
 
@@ -184,7 +184,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioE 25 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/sama5d3xdm.dtsi b/arch/arm/boot/dts/microchip/sama5d3xdm.dtsi
index 3c1c4d62fbf9..3c1c4d62fbf9 100644
--- a/arch/arm/boot/dts/sama5d3xdm.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xdm.dtsi
diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb.dtsi
index 35031bbc7e70..3652c9e24124 100644
--- a/arch/arm/boot/dts/sama5d3xmb.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb.dtsi
@@ -26,7 +26,7 @@
 			spi0: spi@f0004000 {
 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -46,7 +46,7 @@
 				wm8904: wm8904@1a {
 					compatible = "wlf,wm8904";
 					reg = <0x1a>;
-					clocks = <&pck0>;
+					clocks = <&pmc PMC_TYPE_SYSTEM 8>;
 					clock-names = "mclk";
 				};
 			};
@@ -60,9 +60,9 @@
 					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
 					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
 					/* use pck1 for the master clock of ov2640 */
-					clocks = <&pck1>;
+					clocks = <&pmc PMC_TYPE_SYSTEM 9>;
 					clock-names = "xvclk";
-					assigned-clocks = <&pck1>;
+					assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
 					assigned-clock-rates = <25000000>;
 
 					port {
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb_cmp.dtsi
index 8a6916a69da4..5d9e97fecf83 100644
--- a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb_cmp.dtsi
@@ -25,7 +25,7 @@
 			spi0: spi@f0004000 {
 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -45,7 +45,7 @@
 				wm8904: wm8904@1a {
 					compatible = "wlf,wm8904";
 					reg = <0x1a>;
-					clocks = <&pck0>;
+					clocks = <&pmc PMC_TYPE_SYSTEM 8>;
 					clock-names = "mclk";
 				};
 			};
@@ -59,9 +59,9 @@
 					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
 					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
 					/* use pck1 for the master clock of ov2640 */
-					clocks = <&pck1>;
+					clocks = <&pmc PMC_TYPE_SYSTEM 9>;
 					clock-names = "xvclk";
-					assigned-clocks = <&pck1>;
+					assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>;
 					assigned-clock-rates = <25000000>;
 
 					port {
diff --git a/arch/arm/boot/dts/sama5d3xmb_emac.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb_emac.dtsi
index a5dd41cd9522..a5dd41cd9522 100644
--- a/arch/arm/boot/dts/sama5d3xmb_emac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb_emac.dtsi
diff --git a/arch/arm/boot/dts/sama5d3xmb_gmac.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb_gmac.dtsi
index d750da38ff3c..d750da38ff3c 100644
--- a/arch/arm/boot/dts/sama5d3xmb_gmac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb_gmac.dtsi
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/microchip/sama5d4.dtsi
index 6ab27a7b388d..58ceed997889 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d4.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/clock/at91.h>
 #include <dt-bindings/dma/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -53,7 +54,7 @@
 		};
 	};
 
-	memory {
+	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x20000000>;
 	};
@@ -71,7 +72,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -81,6 +82,9 @@
 	ns_sram: sram@210000 {
 		compatible = "mmio-sram";
 		reg = <0x00210000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00210000 0x10000>;
 	};
 
 	ahb {
@@ -93,11 +97,19 @@
 			compatible = "mmio-sram";
 			no-memory-wc;
 			reg = <0x100000 0x2400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x100000 0x2400>;
+		};
+
+		vdec0: vdec@300000 {
+			compatible = "microchip,sama5d4-vdec";
+			reg = <0x00300000 0x100000>;
+			interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
 		};
 
 		usb0: gadget@400000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "atmel,sama5d3-udc";
 			reg = <0x00400000 0x100000
 			       0xfc02c000 0x4000>;
@@ -105,124 +117,6 @@
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
 			clock-names = "pclk", "hclk";
 			status = "disabled";
-
-			ep@0 {
-				reg = <0>;
-				atmel,fifo-size = <64>;
-				atmel,nb-banks = <1>;
-			};
-
-			ep@1 {
-				reg = <1>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <3>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@2 {
-				reg = <2>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <3>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@3 {
-				reg = <3>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@4 {
-				reg = <4>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@5 {
-				reg = <5>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@6 {
-				reg = <6>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@7 {
-				reg = <7>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-dma;
-				atmel,can-isoc;
-			};
-
-			ep@8 {
-				reg = <8>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@9 {
-				reg = <9>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@10 {
-				reg = <10>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@11 {
-				reg = <11>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@12 {
-				reg = <12>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@13 {
-				reg = <13>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@14 {
-				reg = <14>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
-
-			ep@15 {
-				reg = <15>;
-				atmel,fifo-size = <1024>;
-				atmel,nb-banks = <2>;
-				atmel,can-isoc;
-			};
 		};
 
 		usb1: ohci@500000 {
@@ -356,7 +250,7 @@
 				clock-names = "dma_clk";
 			};
 
-			pmc: pmc@f0018000 {
+			pmc: clock-controller@f0018000 {
 				compatible = "atmel,sama5d4-pmc", "syscon";
 				reg = <0xf0018000 0x120>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -385,6 +279,7 @@
 			uart0: serial@f8004000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8004000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -458,8 +353,11 @@
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
 					| AT91_XDMAC_DT_PERID(3))>;
 				dma-names = "tx", "rx";
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c0>;
+				pinctrl-1 = <&pinctrl_i2c0_gpio>;
+				sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
@@ -477,8 +375,11 @@
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
 					| AT91_XDMAC_DT_PERID(5))>;
 				dma-names = "tx", "rx";
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c1>;
+				pinctrl-1 = <&pinctrl_i2c1_gpio>;
+				sda-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioE 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
@@ -519,8 +420,11 @@
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
 					| AT91_XDMAC_DT_PERID(7))>;
 				dma-names = "tx", "rx";
-				pinctrl-names = "default";
+				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&pinctrl_i2c2>;
+				pinctrl-1 = <&pinctrl_i2c2_gpio>;
+				sda-gpios = <&pioB 29 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&pioB 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
@@ -535,6 +439,7 @@
 			usart0: serial@f802c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf802c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -553,6 +458,7 @@
 			usart1: serial@f8030000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8030000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -588,6 +494,7 @@
 			uart1: serial@fc004000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc004000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -606,6 +513,7 @@
 			usart2: serial@fc008000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc008000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -624,6 +532,7 @@
 			usart3: serial@fc00c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc00c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -642,6 +551,7 @@
 			usart4: serial@fc010000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc010000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <31 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -766,34 +676,12 @@
 				atmel,adc-startup-time = <40>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-vref = <3000>;
-				atmel,adc-res = <8 10>;
 				atmel,adc-sample-hold-time = <11>;
-				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "disabled";
-
-				trigger0 {
-					trigger-name = "external-rising";
-					trigger-value = <0x1>;
-					trigger-external;
-				};
-				trigger1 {
-					trigger-name = "external-falling";
-					trigger-value = <0x2>;
-					trigger-external;
-				};
-				trigger2 {
-					trigger-name = "external-any";
-					trigger-value = <0x3>;
-					trigger-external;
-				};
-				trigger3 {
-					trigger-name = "continuous";
-					trigger-value = <0x6>;
-				};
 			};
 
-			aes@fc044000 {
+			aes: crypto@fc044000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xfc044000 0x100>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -804,10 +692,9 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "aes_clk";
-				status = "okay";
 			};
 
-			tdes@fc04c000 {
+			tdes: crypto@fc04c000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xfc04c000 0x100>;
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -818,10 +705,9 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
 				clock-names = "tdes_clk";
-				status = "okay";
 			};
 
-			sha@fc050000 {
+			sha: crypto@fc050000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xfc050000 0x100>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -830,7 +716,6 @@
 				dma-names = "tx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
 				clock-names = "sha_clk";
-				status = "okay";
 			};
 
 			hsmc: smc@fc05c000 {
@@ -849,13 +734,13 @@
 				};
 			};
 
-			reset_controller: rstc@fc068600 {
+			reset_controller: reset-controller@fc068600 {
 				compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
 				reg = <0xfc068600 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shdwc@fc068610 {
+			shutdown_controller: poweroff@fc068610 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfc068610 0x10>;
 				clocks = <&clk32k>;
@@ -876,7 +761,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fc068650 {
+			clk32k: clock-controller@fc068650 {
 				compatible = "atmel,sama5d4-sckc";
 				reg = <0xfc068650 0x4>;
 				#clock-cells = <0>;
@@ -884,7 +769,7 @@
 			};
 
 			rtc@fc0686b0 {
-				compatible = "atmel,at91rm9200-rtc";
+				compatible = "atmel,sama5d4-rtc";
 				reg = <0xfc0686b0 0x30>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				clocks = <&clk32k>;
@@ -893,6 +778,7 @@
 			dbgu: serial@fc069000 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfc069000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -914,7 +800,7 @@
 					0xffffffff 0x3ffcfe7c 0x1c010101	/* pioA */
 					0x7fffffff 0xfffccc3a 0x3f00cc3a	/* pioB */
 					0xffffffff 0x3ff83fff 0xff00ffff	/* pioC */
-					0x0003ff00 0x8002a800 0x00000000	/* pioD */
+					0xb003ff00 0x8002a800 0x00000000	/* pioD */
 					0xffffffff 0x7fffffff 0x76fff1bf	/* pioE */
 					>;
 
@@ -1122,6 +1008,12 @@
 							<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE
 							 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
 					};
+
+					pinctrl_i2c0_gpio: i2c0-gpio {
+						atmel,pins =
+							<AT91_PIOA 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOA 31 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 
 				i2c1 {
@@ -1130,6 +1022,12 @@
 							<AT91_PIOE 29 AT91_PERIPH_C AT91_PINCTRL_NONE	/* TWD1, conflicts with UART0 RX and DIBP */
 							 AT91_PIOE 30 AT91_PERIPH_C AT91_PINCTRL_NONE>;	/* TWCK1, conflicts with UART0 TX and DIBN */
 					};
+
+					pinctrl_i2c1_gpio: i2c1-gpio {
+						atmel,pins =
+							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOE 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 
 				i2c2 {
@@ -1138,6 +1036,12 @@
 							<AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE	/* TWD2, conflicts with RD0 and PWML1 */
 							 AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* TWCK2, conflicts with RF0 */
 					};
+
+					pinctrl_i2c2_gpio: i2c2-gpio {
+						atmel,pins =
+							<AT91_PIOB 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+							 AT91_PIOB 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 				};
 
 				isi {
diff --git a/arch/arm/boot/dts/microchip/sama7g5-pinfunc.h b/arch/arm/boot/dts/microchip/sama7g5-pinfunc.h
new file mode 100644
index 000000000000..a67a156e26ab
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sama7g5-pinfunc.h
@@ -0,0 +1,923 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+#define PINMUX_PIN(no, func, ioset) \
+(((no) & 0xffff) | (((func) & 0xf) << 16) | (((ioset) & 0xff) << 20))
+
+#define PIN_PA0				0
+#define PIN_PA0__GPIO			PINMUX_PIN(PIN_PA0, 0, 0)
+#define PIN_PA0__SDMMC0_CK		PINMUX_PIN(PIN_PA0, 1, 1)
+#define PIN_PA0__FLEXCOM0_IO0		PINMUX_PIN(PIN_PA0, 2, 1)
+#define PIN_PA0__CANTX3			PINMUX_PIN(PIN_PA0, 3, 1)
+#define PIN_PA0__PWML0			PINMUX_PIN(PIN_PA0, 5, 2)
+#define PIN_PA1				1
+#define PIN_PA1__GPIO			PINMUX_PIN(PIN_PA1, 0, 0)
+#define PIN_PA1__SDMMC0_CMD		PINMUX_PIN(PIN_PA1, 1, 1)
+#define PIN_PA1__FLEXCOM0_IO1		PINMUX_PIN(PIN_PA1, 2, 1)
+#define PIN_PA1__CANRX3			PINMUX_PIN(PIN_PA1, 3, 1)
+#define PIN_PA1__D14			PINMUX_PIN(PIN_PA1, 4, 1)
+#define PIN_PA1__PWMH0			PINMUX_PIN(PIN_PA1, 5, 3)
+#define PIN_PA2				2
+#define PIN_PA2__GPIO			PINMUX_PIN(PIN_PA2, 0, 0)
+#define PIN_PA2__SDMMC0_RSTN		PINMUX_PIN(PIN_PA2, 1, 1)
+#define PIN_PA2__FLEXCOM0_IO2		PINMUX_PIN(PIN_PA2, 2, 1)
+#define PIN_PA2__PDMC1_CLK		PINMUX_PIN(PIN_PA2, 3, 1)
+#define PIN_PA2__D15			PINMUX_PIN(PIN_PA2, 4, 1)
+#define PIN_PA2__PWMH1			PINMUX_PIN(PIN_PA2, 5, 3)
+#define PIN_PA2__FLEXCOM1_IO0		PINMUX_PIN(PIN_PA2, 6, 3)
+#define PIN_PA3				3
+#define PIN_PA3__GPIO			PINMUX_PIN(PIN_PA3, 0, 0)
+#define PIN_PA3__SDMMC0_DAT0		PINMUX_PIN(PIN_PA3, 1, 1)
+#define PIN_PA3__FLEXCOM0_IO3		PINMUX_PIN(PIN_PA3, 2, 1)
+#define PIN_PA3__PDMC1_DS0		PINMUX_PIN(PIN_PA3, 3, 1)
+#define PIN_PA3__NWR1_NBS1		PINMUX_PIN(PIN_PA3, 4, 1)
+#define PIN_PA3__PWML3			PINMUX_PIN(PIN_PA3, 5, 3)
+#define PIN_PA3__FLEXCOM1_IO1		PINMUX_PIN(PIN_PA3, 6, 3)
+#define PIN_PA4				4
+#define PIN_PA4__GPIO			PINMUX_PIN(PIN_PA4, 0, 0)
+#define PIN_PA4__SDMMC0_DAT1		PINMUX_PIN(PIN_PA4, 1, 1)
+#define PIN_PA4__FLEXCOM0_IO4		PINMUX_PIN(PIN_PA4, 2, 1)
+#define PIN_PA4__PDMC1_DS1		PINMUX_PIN(PIN_PA4, 3, 1)
+#define PIN_PA4__NCS2			PINMUX_PIN(PIN_PA4, 4, 1)
+#define PIN_PA4__PWMH3			PINMUX_PIN(PIN_PA4, 5, 3)
+#define PIN_PA4__FLEXCOM2_IO0		PINMUX_PIN(PIN_PA4, 6, 3)
+#define PIN_PA5				5
+#define PIN_PA5__GPIO			PINMUX_PIN(PIN_PA5, 0, 0)
+#define PIN_PA5__SDMMC0_DAT2		PINMUX_PIN(PIN_PA5, 1, 1)
+#define PIN_PA5__FLEXCOM1_IO0		PINMUX_PIN(PIN_PA5, 2, 1)
+#define PIN_PA5__CANTX2			PINMUX_PIN(PIN_PA5, 3, 1)
+#define PIN_PA5__A23			PINMUX_PIN(PIN_PA5, 4, 1)
+#define PIN_PA5__PWMEXTRG0		PINMUX_PIN(PIN_PA5, 5, 3)
+#define PIN_PA5__FLEXCOM2_IO1		PINMUX_PIN(PIN_PA5, 6, 3)
+#define PIN_PA6				6
+#define PIN_PA6__GPIO			PINMUX_PIN(PIN_PA6, 0, 0)
+#define PIN_PA6__SDMMC0_DAT3		PINMUX_PIN(PIN_PA6, 1, 1)
+#define PIN_PA6__FLEXCOM1_IO1		PINMUX_PIN(PIN_PA6, 2, 1)
+#define PIN_PA6__CANRX2			PINMUX_PIN(PIN_PA6, 3, 1)
+#define PIN_PA6__A24			PINMUX_PIN(PIN_PA6, 4, 1)
+#define PIN_PA6__PWMEXTRG1		PINMUX_PIN(PIN_PA6, 5, 3)
+#define PIN_PA6__FLEXCOM3_IO0		PINMUX_PIN(PIN_PA6, 6, 3)
+#define PIN_PA7				7
+#define PIN_PA7__GPIO			PINMUX_PIN(PIN_PA7, 0, 0)
+#define PIN_PA7__SDMMC0_DAT4		PINMUX_PIN(PIN_PA7, 1, 1)
+#define PIN_PA7__FLEXCOM2_IO0		PINMUX_PIN(PIN_PA7, 2, 1)
+#define PIN_PA7__CANTX1			PINMUX_PIN(PIN_PA7, 3, 1)
+#define PIN_PA7__NWAIT			PINMUX_PIN(PIN_PA7, 4, 1)
+#define PIN_PA7__PWMFI0			PINMUX_PIN(PIN_PA7, 5, 3)
+#define PIN_PA7__FLEXCOM3_IO1		PINMUX_PIN(PIN_PA7, 6, 3)
+#define PIN_PA8				8
+#define PIN_PA8__GPIO			PINMUX_PIN(PIN_PA8, 0, 0)
+#define PIN_PA8__SDMMC0_DAT5		PINMUX_PIN(PIN_PA8, 1, 1)
+#define PIN_PA8__FLEXCOM2_IO1		PINMUX_PIN(PIN_PA8, 2, 1)
+#define PIN_PA8__CANRX1			PINMUX_PIN(PIN_PA8, 3, 1)
+#define PIN_PA8__NCS0			PINMUX_PIN(PIN_PA8, 4, 1)
+#define PIN_PA8__PWMIF1			PINMUX_PIN(PIN_PA8, 5, 3)
+#define PIN_PA8__FLEXCOM4_IO0		PINMUX_PIN(PIN_PA8, 6, 3)
+#define PIN_PA9				9
+#define PIN_PA9__GPIO			PINMUX_PIN(PIN_PA9, 0, 0)
+#define PIN_PA9__SDMMC0_DAT6		PINMUX_PIN(PIN_PA9, 1, 1)
+#define PIN_PA9__FLEXCOM2_IO2		PINMUX_PIN(PIN_PA9, 2, 1)
+#define PIN_PA9__CANTX0			PINMUX_PIN(PIN_PA9, 3, 1)
+#define PIN_PA9__SMCK			PINMUX_PIN(PIN_PA9, 4, 1)
+#define PIN_PA9__SPDIF_RX		PINMUX_PIN(PIN_PA9, 5, 1)
+#define PIN_PA9__FLEXCOM4_IO1		PINMUX_PIN(PIN_PA9, 6, 3)
+#define PIN_PA10			10
+#define PIN_PA10__GPIO			PINMUX_PIN(PIN_PA10, 0, 0)
+#define PIN_PA10__SDMMC0_DAT7		PINMUX_PIN(PIN_PA10, 1, 1)
+#define PIN_PA10__FLEXCOM2_IO3		PINMUX_PIN(PIN_PA10, 2, 1)
+#define PIN_PA10__CANRX0		PINMUX_PIN(PIN_PA10, 3, 1)
+#define PIN_PA10__NCS1			PINMUX_PIN(PIN_PA10, 4, 1)
+#define PIN_PA10__SPDIF_TX		PINMUX_PIN(PIN_PA10, 5, 1)
+#define PIN_PA10__FLEXCOM5_IO0		PINMUX_PIN(PIN_PA10, 6, 3)
+#define PIN_PA11			11
+#define PIN_PA11__GPIO			PINMUX_PIN(PIN_PA11, 0, 0)
+#define PIN_PA11__SDMMC0_DS		PINMUX_PIN(PIN_PA11, 1, 1)
+#define PIN_PA11__FLEXCOM2_IO4		PINMUX_PIN(PIN_PA11, 2, 1)
+#define PIN_PA11__A0_NBS0		PINMUX_PIN(PIN_PA11, 4, 1)
+#define PIN_PA11__TIOA0			PINMUX_PIN(PIN_PA11, 5, 1)
+#define PIN_PA11__FLEXCOM5_IO1		PINMUX_PIN(PIN_PA11, 6, 3)
+#define PIN_PA12			12
+#define PIN_PA12__GPIO			PINMUX_PIN(PIN_PA12, 0, 0)
+#define PIN_PA12__SDMMC0_WP		PINMUX_PIN(PIN_PA12, 1, 1)
+#define PIN_PA12__FLEXCOM1_IO3		PINMUX_PIN(PIN_PA12, 2, 1)
+#define PIN_PA12__FLEXCOM3_IO5		PINMUX_PIN(PIN_PA12, 4, 1)
+#define PIN_PA12__PWML2			PINMUX_PIN(PIN_PA12, 5, 3)
+#define PIN_PA12__FLEXCOM6_IO0		PINMUX_PIN(PIN_PA12, 6, 3)
+#define PIN_PA13			13
+#define PIN_PA13__GPIO			PINMUX_PIN(PIN_PA13, 0, 0)
+#define PIN_PA13__SDMMC0_1V8SEL		PINMUX_PIN(PIN_PA13, 1, 1)
+#define PIN_PA13__FLEXCOM1_IO2		PINMUX_PIN(PIN_PA13, 2, 1)
+#define PIN_PA13__FLEXCOM3_IO6		PINMUX_PIN(PIN_PA13, 4, 1)
+#define PIN_PA13__PWMH2			PINMUX_PIN(PIN_PA13, 5, 3)
+#define PIN_PA13__FLEXCOM6_IO1		PINMUX_PIN(PIN_PA13, 6, 3)
+#define PIN_PA14			14
+#define PIN_PA14__GPIO			PINMUX_PIN(PIN_PA14, 0, 0)
+#define PIN_PA14__SDMMC0_CD		PINMUX_PIN(PIN_PA14, 1, 1)
+#define PIN_PA14__FLEXCOM1_IO4		PINMUX_PIN(PIN_PA14, 2, 1)
+#define PIN_PA14__A25			PINMUX_PIN(PIN_PA14, 4, 1)
+#define PIN_PA14__PWML1			PINMUX_PIN(PIN_PA14, 5, 3)
+#define PIN_PA15			15
+#define PIN_PA15__GPIO			PINMUX_PIN(PIN_PA15, 0, 0)
+#define PIN_PA15__G0_TXEN		PINMUX_PIN(PIN_PA15, 1, 1)
+#define PIN_PA15__FLEXCOM3_IO0		PINMUX_PIN(PIN_PA15, 2, 1)
+#define PIN_PA15__ISC_MCK		PINMUX_PIN(PIN_PA15, 3, 1)
+#define PIN_PA15__A1			PINMUX_PIN(PIN_PA15, 4, 1)
+#define PIN_PA15__TIOB0			PINMUX_PIN(PIN_PA15, 5, 1)
+#define PIN_PA16			16
+#define PIN_PA16__GPIO			PINMUX_PIN(PIN_PA16, 0, 0)
+#define PIN_PA16__G0_TX0		PINMUX_PIN(PIN_PA16, 1, 1)
+#define PIN_PA16__FLEXCOM3_IO1		PINMUX_PIN(PIN_PA16, 2, 1)
+#define PIN_PA16__ISC_D0		PINMUX_PIN(PIN_PA16, 3, 1)
+#define PIN_PA16__A2			PINMUX_PIN(PIN_PA16, 4, 1)
+#define PIN_PA16__TCLK0			PINMUX_PIN(PIN_PA16, 5, 1)
+#define PIN_PA17			17
+#define PIN_PA17__GPIO			PINMUX_PIN(PIN_PA17, 0, 0)
+#define PIN_PA17__G0_TX1		PINMUX_PIN(PIN_PA17, 1, 1)
+#define PIN_PA17__FLEXCOM3_IO2		PINMUX_PIN(PIN_PA17, 2, 1)
+#define PIN_PA17__ISC_D1		PINMUX_PIN(PIN_PA17, 3, 1)
+#define PIN_PA17__A3			PINMUX_PIN(PIN_PA17, 4, 1)
+#define PIN_PA17__TIOA1			PINMUX_PIN(PIN_PA17, 5, 1)
+#define PIN_PA18			18
+#define PIN_PA18__GPIO			PINMUX_PIN(PIN_PA18, 0, 0)
+#define PIN_PA18__G0_RXDV		PINMUX_PIN(PIN_PA18, 1, 1)
+#define PIN_PA18__FLEXCOM3_IO3		PINMUX_PIN(PIN_PA18, 2, 1)
+#define PIN_PA18__ISC_D2		PINMUX_PIN(PIN_PA18, 3, 1)
+#define PIN_PA18__A4			PINMUX_PIN(PIN_PA18, 4, 1)
+#define PIN_PA18__TIOB1			PINMUX_PIN(PIN_PA18, 5, 1)
+#define PIN_PA19			19
+#define PIN_PA19__GPIO			PINMUX_PIN(PIN_PA19, 0, 0)
+#define PIN_PA19__G0_RX0		PINMUX_PIN(PIN_PA19, 1, 1)
+#define PIN_PA19__FLEXCOM3_IO4		PINMUX_PIN(PIN_PA19, 2, 1)
+#define PIN_PA19__ISC_D3		PINMUX_PIN(PIN_PA19, 3, 1)
+#define PIN_PA19__A5			PINMUX_PIN(PIN_PA19, 4, 1)
+#define PIN_PA19__TCLK1			PINMUX_PIN(PIN_PA19, 5, 1)
+#define PIN_PA20			20
+#define PIN_PA20__GPIO			PINMUX_PIN(PIN_PA20, 0, 0)
+#define PIN_PA20__G0_RX1		PINMUX_PIN(PIN_PA20, 1, 1)
+#define PIN_PA20__FLEXCOM4_IO0		PINMUX_PIN(PIN_PA20, 2, 1)
+#define PIN_PA20__ISC_D4		PINMUX_PIN(PIN_PA20, 3, 1)
+#define PIN_PA20__A6			PINMUX_PIN(PIN_PA20, 4, 1)
+#define PIN_PA20__TIOA2			PINMUX_PIN(PIN_PA20, 5, 1)
+#define PIN_PA21			21
+#define PIN_PA21__GPIO			PINMUX_PIN(PIN_PA21, 0, 0)
+#define PIN_PA21__G0_RXER		PINMUX_PIN(PIN_PA21, 1, 1)
+#define PIN_PA21__FLEXCOM4_IO1		PINMUX_PIN(PIN_PA21, 2, 1)
+#define PIN_PA21__ISC_D5		PINMUX_PIN(PIN_PA21, 3, 1)
+#define PIN_PA21__A7			PINMUX_PIN(PIN_PA21, 4, 1)
+#define PIN_PA21__TIOB2			PINMUX_PIN(PIN_PA21, 5, 1)
+#define PIN_PA22			22
+#define PIN_PA22__GPIO			PINMUX_PIN(PIN_PA22, 0, 0)
+#define PIN_PA22__G0_MDC		PINMUX_PIN(PIN_PA22, 1, 1)
+#define PIN_PA22__FLEXCOM4_IO2		PINMUX_PIN(PIN_PA22, 2, 1)
+#define PIN_PA22__ISC_D6		PINMUX_PIN(PIN_PA22, 3, 1)
+#define PIN_PA22__A8			PINMUX_PIN(PIN_PA22, 4, 1)
+#define PIN_PA22__TCLK2			PINMUX_PIN(PIN_PA22, 5, 1)
+#define PIN_PA23			23
+#define PIN_PA23__GPIO			PINMUX_PIN(PIN_PA23, 0, 0)
+#define PIN_PA23__G0_MDIO		PINMUX_PIN(PIN_PA23, 1, 1)
+#define PIN_PA23__FLEXCOM4_IO3		PINMUX_PIN(PIN_PA23, 2, 1)
+#define PIN_PA23__ISC_D7		PINMUX_PIN(PIN_PA23, 3, 1)
+#define PIN_PA23__A9			PINMUX_PIN(PIN_PA23, 4, 1)
+#define PIN_PA24			24
+#define PIN_PA24__GPIO			PINMUX_PIN(PIN_PA24, 0, 0)
+#define PIN_PA24__G0_TXCK		PINMUX_PIN(PIN_PA24, 1, 1)
+#define PIN_PA24__FLEXCOM4_IO4		PINMUX_PIN(PIN_PA24, 2, 1)
+#define PIN_PA24__ISC_HSYNC		PINMUX_PIN(PIN_PA24, 3, 1)
+#define PIN_PA24__A10			PINMUX_PIN(PIN_PA24, 4, 1)
+#define PIN_PA24__FLEXCOM0_IO5		PINMUX_PIN(PIN_PA24, 5, 1)
+#define PIN_PA25			25
+#define PIN_PA25__GPIO			PINMUX_PIN(PIN_PA25, 0, 0)
+#define PIN_PA25__G0_125CK		PINMUX_PIN(PIN_PA25, 1, 1)
+#define PIN_PA25__FLEXCOM5_IO4		PINMUX_PIN(PIN_PA25, 2, 1)
+#define PIN_PA25__ISC_VSYNC		PINMUX_PIN(PIN_PA25, 3, 1)
+#define PIN_PA25__A11			PINMUX_PIN(PIN_PA25, 4, 1)
+#define PIN_PA25__FLEXCOM0_IO6		PINMUX_PIN(PIN_PA25, 5, 1)
+#define PIN_PA25__FLEXCOM7_IO0		PINMUX_PIN(PIN_PA25, 6, 3)
+#define PIN_PA26			26
+#define PIN_PA26__GPIO			PINMUX_PIN(PIN_PA26, 0, 0)
+#define PIN_PA26__G0_TX2		PINMUX_PIN(PIN_PA26, 1, 1)
+#define PIN_PA26__FLEXCOM5_IO2		PINMUX_PIN(PIN_PA26, 2, 1)
+#define PIN_PA26__ISC_FIELD		PINMUX_PIN(PIN_PA26, 3, 1)
+#define PIN_PA26__A12			PINMUX_PIN(PIN_PA26, 4, 1)
+#define PIN_PA26__TF0			PINMUX_PIN(PIN_PA26, 5, 1)
+#define PIN_PA26__FLEXCOM7_IO1		PINMUX_PIN(PIN_PA26, 6, 3)
+#define PIN_PA27			27
+#define PIN_PA27__GPIO			PINMUX_PIN(PIN_PA27, 0, 0)
+#define PIN_PA27__G0_TX3		PINMUX_PIN(PIN_PA27, 1, 1)
+#define PIN_PA27__FLEXCOM5_IO3		PINMUX_PIN(PIN_PA27, 2, 1)
+#define PIN_PA27__ISC_PCK		PINMUX_PIN(PIN_PA27, 3, 1)
+#define PIN_PA27__A13			PINMUX_PIN(PIN_PA27, 4, 1)
+#define PIN_PA27__TK0			PINMUX_PIN(PIN_PA27, 5, 1)
+#define PIN_PA27__FLEXCOM8_IO0		PINMUX_PIN(PIN_PA27, 6, 3)
+#define PIN_PA28			28
+#define PIN_PA28__GPIO			PINMUX_PIN(PIN_PA28, 0, 0)
+#define PIN_PA28__G0_RX2		PINMUX_PIN(PIN_PA28, 1, 1)
+#define PIN_PA28__FLEXCOM5_IO0		PINMUX_PIN(PIN_PA28, 2, 1)
+#define PIN_PA28__ISC_D8		PINMUX_PIN(PIN_PA28, 3, 1)
+#define PIN_PA28__A14			PINMUX_PIN(PIN_PA28, 4, 1)
+#define PIN_PA28__RD0			PINMUX_PIN(PIN_PA28, 5, 1)
+#define PIN_PA28__FLEXCOM8_IO1		PINMUX_PIN(PIN_PA28, 6, 3)
+#define PIN_PA29			29
+#define PIN_PA29__GPIO			PINMUX_PIN(PIN_PA29, 0, 0)
+#define PIN_PA29__G0_RX3		PINMUX_PIN(PIN_PA29, 1, 1)
+#define PIN_PA29__FLEXCOM5_IO1		PINMUX_PIN(PIN_PA29, 2, 1)
+#define PIN_PA29__ISC_D9		PINMUX_PIN(PIN_PA29, 3, 1)
+#define PIN_PA29__A15			PINMUX_PIN(PIN_PA29, 4, 1)
+#define PIN_PA29__RF0			PINMUX_PIN(PIN_PA29, 5, 1)
+#define PIN_PA29__FLEXCOM9_IO0		PINMUX_PIN(PIN_PA29, 6, 3)
+#define PIN_PA30			30
+#define PIN_PA30__GPIO			PINMUX_PIN(PIN_PA30, 0, 0)
+#define PIN_PA30__G0_RXCK		PINMUX_PIN(PIN_PA30, 1, 1)
+#define PIN_PA30__FLEXCOM6_IO4		PINMUX_PIN(PIN_PA30, 2, 1)
+#define PIN_PA30__ISC_D10		PINMUX_PIN(PIN_PA30, 3, 1)
+#define PIN_PA30__A16			PINMUX_PIN(PIN_PA30, 4, 1)
+#define PIN_PA30__RK0			PINMUX_PIN(PIN_PA30, 5, 1)
+#define PIN_PA30__FLEXCOM9_IO1		PINMUX_PIN(PIN_PA30, 6, 3)
+#define PIN_PA31			31
+#define PIN_PA31__GPIO			PINMUX_PIN(PIN_PA31, 0, 0)
+#define PIN_PA31__G0_TXER		PINMUX_PIN(PIN_PA31, 1, 1)
+#define PIN_PA31__FLEXCOM6_IO2		PINMUX_PIN(PIN_PA31, 2, 1)
+#define PIN_PA31__ISC_D11		PINMUX_PIN(PIN_PA31, 3, 1)
+#define PIN_PA31__A17			PINMUX_PIN(PIN_PA31, 4, 1)
+#define PIN_PA31__TD0			PINMUX_PIN(PIN_PA31, 5, 1)
+#define PIN_PA31__FLEXCOM10_IO0		PINMUX_PIN(PIN_PA31, 6, 3)
+#define PIN_PB0				32
+#define PIN_PB0__GPIO			PINMUX_PIN(PIN_PB0, 0, 0)
+#define PIN_PB0__G0_COL			PINMUX_PIN(PIN_PB0, 1, 1)
+#define PIN_PB0__FLEXCOM6_IO3		PINMUX_PIN(PIN_PB0, 2, 2)
+#define PIN_PB0__EXT_IRQ0		PINMUX_PIN(PIN_PB0, 3, 1)
+#define PIN_PB0__A18			PINMUX_PIN(PIN_PB0, 4, 1)
+#define PIN_PB0__SPDIF_RX		PINMUX_PIN(PIN_PB0, 5, 2)
+#define PIN_PB0__FLEXCOM10_IO1		PINMUX_PIN(PIN_PB0, 6, 3)
+#define PIN_PB1				33
+#define PIN_PB1__GPIO			PINMUX_PIN(PIN_PB1, 0, 0)
+#define PIN_PB1__G0_CRS			PINMUX_PIN(PIN_PB1, 1, 1)
+#define PIN_PB1__FLEXCOM6_IO1		PINMUX_PIN(PIN_PB1, 2, 2)
+#define PIN_PB1__EXT_IRQ1		PINMUX_PIN(PIN_PB1, 3, 1)
+#define PIN_PB1__A19			PINMUX_PIN(PIN_PB1, 4, 1)
+#define PIN_PB1__SPDIF_TX		PINMUX_PIN(PIN_PB1, 5, 2)
+#define PIN_PB1__FLEXCOM11_IO0		PINMUX_PIN(PIN_PB1, 6, 3)
+#define PIN_PB2				34
+#define PIN_PB2__GPIO			PINMUX_PIN(PIN_PB2, 0, 0)
+#define PIN_PB2__G0_TSUCOMP		PINMUX_PIN(PIN_PB2, 1, 1)
+#define PIN_PB2__FLEXCOM6_IO0		PINMUX_PIN(PIN_PB2, 2, 1)
+#define PIN_PB2__ADTRG			PINMUX_PIN(PIN_PB2, 3, 1)
+#define PIN_PB2__A20			PINMUX_PIN(PIN_PB2, 4, 1)
+#define PIN_PB2__FLEXCOM11_IO1		PINMUX_PIN(PIN_PB2, 6, 3)
+#define PIN_PB3				35
+#define PIN_PB3__GPIO			PINMUX_PIN(PIN_PB3, 0, 0)
+#define PIN_PB3__RF1			PINMUX_PIN(PIN_PB3, 1, 1)
+#define PIN_PB3__FLEXCOM11_IO0		PINMUX_PIN(PIN_PB3, 2, 1)
+#define PIN_PB3__PCK2			PINMUX_PIN(PIN_PB3, 3, 2)
+#define PIN_PB3__D8			PINMUX_PIN(PIN_PB3, 4, 1)
+#define PIN_PB4				36
+#define PIN_PB4__GPIO			PINMUX_PIN(PIN_PB4, 0, 0)
+#define PIN_PB4__TF1			PINMUX_PIN(PIN_PB4, 1, 1)
+#define PIN_PB4__FLEXCOM11_IO1		PINMUX_PIN(PIN_PB4, 2, 1)
+#define PIN_PB4__PCK3			PINMUX_PIN(PIN_PB4, 3, 2)
+#define PIN_PB4__D9			PINMUX_PIN(PIN_PB4, 4, 1)
+#define PIN_PB5				37
+#define PIN_PB5__GPIO			PINMUX_PIN(PIN_PB5, 0, 0)
+#define PIN_PB5__TK1			PINMUX_PIN(PIN_PB5, 1, 1)
+#define PIN_PB5__FLEXCOM11_IO2		PINMUX_PIN(PIN_PB5, 2, 1)
+#define PIN_PB5__PCK4			PINMUX_PIN(PIN_PB5, 3, 2)
+#define PIN_PB5__D10			PINMUX_PIN(PIN_PB5, 4, 1)
+#define PIN_PB6				38
+#define PIN_PB6__GPIO			PINMUX_PIN(PIN_PB6, 0, 0)
+#define PIN_PB6__RK1			PINMUX_PIN(PIN_PB6, 1, 1)
+#define PIN_PB6__FLEXCOM11_IO3		PINMUX_PIN(PIN_PB6, 2, 1)
+#define PIN_PB6__PCK5			PINMUX_PIN(PIN_PB6, 3, 2)
+#define PIN_PB6__D11			PINMUX_PIN(PIN_PB6, 4, 1)
+#define PIN_PB7				39
+#define PIN_PB7__GPIO			PINMUX_PIN(PIN_PB7, 0, 0)
+#define PIN_PB7__TD1			PINMUX_PIN(PIN_PB7, 1, 1)
+#define PIN_PB7__FLEXCOM11_IO4		PINMUX_PIN(PIN_PB7, 2, 1)
+#define PIN_PB7__FLEXCOM3_IO5		PINMUX_PIN(PIN_PB7, 3, 2)
+#define PIN_PB7__D12			PINMUX_PIN(PIN_PB7, 4, 1)
+#define PIN_PB8				40
+#define PIN_PB8__GPIO			PINMUX_PIN(PIN_PB8, 0, 0)
+#define PIN_PB8__RD1			PINMUX_PIN(PIN_PB8, 1, 1)
+#define PIN_PB8__FLEXCOM8_IO0		PINMUX_PIN(PIN_PB8, 2, 1)
+#define PIN_PB8__FLEXCOM3_IO6		PINMUX_PIN(PIN_PB8, 3, 2)
+#define PIN_PB8__D13			PINMUX_PIN(PIN_PB8, 4, 1)
+#define PIN_PB9				41
+#define PIN_PB9__GPIO			PINMUX_PIN(PIN_PB9, 0, 0)
+#define PIN_PB9__QSPI0_IO3		PINMUX_PIN(PIN_PB9, 1, 1)
+#define PIN_PB9__FLEXCOM8_IO1		PINMUX_PIN(PIN_PB9, 2, 1)
+#define PIN_PB9__PDMC0_CLK		PINMUX_PIN(PIN_PB9, 3, 1)
+#define PIN_PB9__NCS3_NANDCS		PINMUX_PIN(PIN_PB9, 4, 1)
+#define PIN_PB9__PWML0			PINMUX_PIN(PIN_PB9, 5, 2)
+#define PIN_PB10			42
+#define PIN_PB10__GPIO			PINMUX_PIN(PIN_PB10, 0, 0)
+#define PIN_PB10__QSPI0_IO2		PINMUX_PIN(PIN_PB10, 1, 1)
+#define PIN_PB10__FLEXCOM8_IO2		PINMUX_PIN(PIN_PB10, 2, 1)
+#define PIN_PB10__PDMC0_DS0		PINMUX_PIN(PIN_PB10, 3, 1)
+#define PIN_PB10__NWE_NWR0_NANDWE	PINMUX_PIN(PIN_PB10, 4, 1)
+#define PIN_PB10__PWMH0			PINMUX_PIN(PIN_PB10, 5, 2)
+#define PIN_PB11			43
+#define PIN_PB11__GPIO			PINMUX_PIN(PIN_PB11, 0, 0)
+#define PIN_PB11__QSPI0_IO1		PINMUX_PIN(PIN_PB11, 1, 1)
+#define PIN_PB11__FLEXCOM8_IO3		PINMUX_PIN(PIN_PB11, 2, 1)
+#define PIN_PB11__PDMC0_DS1		PINMUX_PIN(PIN_PB11, 3, 1)
+#define PIN_PB11__NRD_NANDOE		PINMUX_PIN(PIN_PB11, 4, 1)
+#define PIN_PB11__PWML1			PINMUX_PIN(PIN_PB11, 5, 2)
+#define PIN_PB12			44
+#define PIN_PB12__GPIO			PINMUX_PIN(PIN_PB12, 0, 0)
+#define PIN_PB12__QSPI0_IO0		PINMUX_PIN(PIN_PB12, 1, 1)
+#define PIN_PB12__FLEXCOM8_IO4		PINMUX_PIN(PIN_PB12, 2, 1)
+#define PIN_PB12__FLEXCOM6_IO5		PINMUX_PIN(PIN_PB12, 3, 1)
+#define PIN_PB12__A21_NANDALE		PINMUX_PIN(PIN_PB12, 4, 1)
+#define PIN_PB12__PWMH1			PINMUX_PIN(PIN_PB12, 5, 2)
+#define PIN_PB13			45
+#define PIN_PB13__GPIO			PINMUX_PIN(PIN_PB13, 0, 0)
+#define PIN_PB13__QSPI0_CS		PINMUX_PIN(PIN_PB13, 1, 1)
+#define PIN_PB13__FLEXCOM9_IO0		PINMUX_PIN(PIN_PB13, 2, 1)
+#define PIN_PB13__FLEXCOM6_IO6		PINMUX_PIN(PIN_PB13, 3, 1)
+#define PIN_PB13__A22_NANDCLE		PINMUX_PIN(PIN_PB13, 4, 1)
+#define PIN_PB13__PWML2			PINMUX_PIN(PIN_PB13, 5, 2)
+#define PIN_PB14			46
+#define PIN_PB14__GPIO			PINMUX_PIN(PIN_PB14, 0, 0)
+#define PIN_PB14__QSPI0_SCK		PINMUX_PIN(PIN_PB14, 1, 1)
+#define PIN_PB14__FLEXCOM9_IO1		PINMUX_PIN(PIN_PB14, 2, 1)
+#define PIN_PB14__D0			PINMUX_PIN(PIN_PB14, 4, 1)
+#define PIN_PB14__PWMH2			PINMUX_PIN(PIN_PB14, 5, 2)
+#define PIN_PB15			47
+#define PIN_PB15__GPIO			PINMUX_PIN(PIN_PB15, 0, 0)
+#define PIN_PB15__QSPI0_SCKN		PINMUX_PIN(PIN_PB15, 1, 1)
+#define PIN_PB15__FLEXCOM9_IO2		PINMUX_PIN(PIN_PB15, 2, 1)
+#define PIN_PB15__D1			PINMUX_PIN(PIN_PB15, 4, 1)
+#define PIN_PB15__PWML3			PINMUX_PIN(PIN_PB15, 5, 2)
+#define PIN_PB16			48
+#define PIN_PB16__GPIO			PINMUX_PIN(PIN_PB16, 0, 0)
+#define PIN_PB16__QSPI0_IO4		PINMUX_PIN(PIN_PB16, 1, 1)
+#define PIN_PB16__FLEXCOM9_IO3		PINMUX_PIN(PIN_PB16, 2, 1)
+#define PIN_PB16__PCK0			PINMUX_PIN(PIN_PB16, 3, 1)
+#define PIN_PB16__D2			PINMUX_PIN(PIN_PB16, 4, 1)
+#define PIN_PB16__PWMH3			PINMUX_PIN(PIN_PB16, 5, 2)
+#define PIN_PB16__EXT_IRQ0		PINMUX_PIN(PIN_PB16, 6, 2)
+#define PIN_PB17			49
+#define PIN_PB17__GPIO			PINMUX_PIN(PIN_PB17, 0, 0)
+#define PIN_PB17__QSPI0_IO5		PINMUX_PIN(PIN_PB17, 1, 1)
+#define PIN_PB17__FLEXCOM9_IO4		PINMUX_PIN(PIN_PB17, 2, 1)
+#define PIN_PB17__PCK1			PINMUX_PIN(PIN_PB17, 3, 1)
+#define PIN_PB17__D3			PINMUX_PIN(PIN_PB17, 4, 1)
+#define PIN_PB17__PWMEXTRG0		PINMUX_PIN(PIN_PB17, 5, 2)
+#define PIN_PB17__EXT_IRQ1		PINMUX_PIN(PIN_PB17, 6, 2)
+#define PIN_PB18			50
+#define PIN_PB18__GPIO			PINMUX_PIN(PIN_PB18, 0, 0)
+#define PIN_PB18__QSPI0_IO6		PINMUX_PIN(PIN_PB18, 1, 1)
+#define PIN_PB18__FLEXCOM10_IO0		PINMUX_PIN(PIN_PB18, 2, 1)
+#define PIN_PB18__PCK2			PINMUX_PIN(PIN_PB18, 3, 1)
+#define PIN_PB18__D4			PINMUX_PIN(PIN_PB18, 4, 1)
+#define PIN_PB18__PWMEXTRG1		PINMUX_PIN(PIN_PB18, 5, 2)
+#define PIN_PB19			51
+#define PIN_PB19__GPIO			PINMUX_PIN(PIN_PB19, 0, 0)
+#define PIN_PB19__QSPI0_IO7		PINMUX_PIN(PIN_PB19, 1, 1)
+#define PIN_PB19__FLEXCOM10_IO1		PINMUX_PIN(PIN_PB19, 2, 1)
+#define PIN_PB19__PCK3			PINMUX_PIN(PIN_PB19, 3, 1)
+#define PIN_PB19__D5			PINMUX_PIN(PIN_PB19, 4, 1)
+#define PIN_PB19__PWMFI0		PINMUX_PIN(PIN_PB19, 5, 2)
+#define PIN_PB20			52
+#define PIN_PB20__GPIO			PINMUX_PIN(PIN_PB20, 0, 0)
+#define PIN_PB20__QSPI0_DQS		PINMUX_PIN(PIN_PB20, 1, 1)
+#define PIN_PB20__FLEXCOM10_IO2		PINMUX_PIN(PIN_PB20, 2, 1)
+#define PIN_PB20__D6			PINMUX_PIN(PIN_PB20, 4, 1)
+#define PIN_PB20__PWMFI1		PINMUX_PIN(PIN_PB20, 5, 2)
+#define PIN_PB21			53
+#define PIN_PB21__GPIO			PINMUX_PIN(PIN_PB21, 0, 0)
+#define PIN_PB21__QSPI0_INT		PINMUX_PIN(PIN_PB21, 1, 1)
+#define PIN_PB21__FLEXCOM10_IO3		PINMUX_PIN(PIN_PB21, 2, 1)
+#define PIN_PB21__FLEXCOM9_IO5		PINMUX_PIN(PIN_PB21, 3, 1)
+#define PIN_PB21__D7			PINMUX_PIN(PIN_PB21, 4, 1)
+#define PIN_PB22			54
+#define PIN_PB22__GPIO			PINMUX_PIN(PIN_PB22, 0, 0)
+#define PIN_PB22__QSPI1_IO3		PINMUX_PIN(PIN_PB22, 1, 1)
+#define PIN_PB22__FLEXCOM10_IO4		PINMUX_PIN(PIN_PB22, 2, 1)
+#define PIN_PB22__FLEXCOM9_IO6		PINMUX_PIN(PIN_PB22, 3, 1)
+#define PIN_PB22__NANDRDY		PINMUX_PIN(PIN_PB22, 4, 1)
+#define PIN_PB23			55
+#define PIN_PB23__GPIO			PINMUX_PIN(PIN_PB23, 0, 0)
+#define PIN_PB23__QSPI1_IO2		PINMUX_PIN(PIN_PB23, 1, 1)
+#define PIN_PB23__FLEXCOM7_IO0		PINMUX_PIN(PIN_PB23, 2, 1)
+#define PIN_PB23__I2SMCC0_CK		PINMUX_PIN(PIN_PB23, 3, 1)
+#define PIN_PB23__PCK4			PINMUX_PIN(PIN_PB23, 6, 1)
+#define PIN_PB24			56
+#define PIN_PB24__GPIO			PINMUX_PIN(PIN_PB24, 0, 0)
+#define PIN_PB24__QSPI1_IO1		PINMUX_PIN(PIN_PB24, 1, 1)
+#define PIN_PB24__FLEXCOM7_IO1		PINMUX_PIN(PIN_PB24, 2, 1)
+#define PIN_PB24__I2SMCC0_WS		PINMUX_PIN(PIN_PB24, 3, 1)
+#define PIN_PB24__PCK5			PINMUX_PIN(PIN_PB24, 6, 1)
+#define PIN_PB25			57
+#define PIN_PB25__GPIO			PINMUX_PIN(PIN_PB25, 0, 0)
+#define PIN_PB25__QSPI1_IO0		PINMUX_PIN(PIN_PB25, 1, 1)
+#define PIN_PB25__FLEXCOM7_IO2		PINMUX_PIN(PIN_PB25, 2, 1)
+#define PIN_PB25__I2SMCC0_DOUT1		PINMUX_PIN(PIN_PB25, 3, 1)
+#define PIN_PB25__PCK6			PINMUX_PIN(PIN_PB25, 6, 1)
+#define PIN_PB26			58
+#define PIN_PB26__GPIO			PINMUX_PIN(PIN_PB26, 0, 0)
+#define PIN_PB26__QSPI1_CS		PINMUX_PIN(PIN_PB26, 1, 1)
+#define PIN_PB26__FLEXCOM7_IO3		PINMUX_PIN(PIN_PB26, 2, 1)
+#define PIN_PB26__I2SMCC0_DOUT0		PINMUX_PIN(PIN_PB26, 3, 1)
+#define PIN_PB26__PWMEXTRG0		PINMUX_PIN(PIN_PB26, 5, 1)
+#define PIN_PB26__PCK7			PINMUX_PIN(PIN_PB26, 6, 1)
+#define PIN_PB27			59
+#define PIN_PB27__GPIO			PINMUX_PIN(PIN_PB27, 0, 0)
+#define PIN_PB27__QSPI1_SCK		PINMUX_PIN(PIN_PB27, 1, 1)
+#define PIN_PB27__FLEXCOM7_IO4		PINMUX_PIN(PIN_PB27, 2, 1)
+#define PIN_PB27__I2SMCC0_MCK		PINMUX_PIN(PIN_PB27, 3, 1)
+#define PIN_PB27__PWMEXTRG1		PINMUX_PIN(PIN_PB27, 5, 1)
+#define PIN_PB28			60
+#define PIN_PB28__GPIO			PINMUX_PIN(PIN_PB28, 0, 0)
+#define PIN_PB28__SDMMC1_RSTN		PINMUX_PIN(PIN_PB28, 1, 1)
+#define PIN_PB28__ADTRG			PINMUX_PIN(PIN_PB28, 2, 2)
+#define PIN_PB28__PWMFI0		PINMUX_PIN(PIN_PB28, 5, 1)
+#define PIN_PB28__FLEXCOM7_IO0		PINMUX_PIN(PIN_PB28, 6, 4)
+#define PIN_PB29			61
+#define PIN_PB29__GPIO			PINMUX_PIN(PIN_PB29, 0, 0)
+#define PIN_PB29__SDMMC1_CMD		PINMUX_PIN(PIN_PB29, 1, 1)
+#define PIN_PB29__FLEXCOM3_IO2		PINMUX_PIN(PIN_PB29, 2, 2)
+#define PIN_PB29__FLEXCOM0_IO5		PINMUX_PIN(PIN_PB29, 3, 2)
+#define PIN_PB29__TIOA3			PINMUX_PIN(PIN_PB29, 4, 2)
+#define PIN_PB29__PWMFI1		PINMUX_PIN(PIN_PB29, 5, 1)
+#define PIN_PB29__FLEXCOM7_IO1		PINMUX_PIN(PIN_PB29, 6, 4)
+#define PIN_PB30			62
+#define PIN_PB30__GPIO			PINMUX_PIN(PIN_PB30, 0, 0)
+#define PIN_PB30__SDMMC1_CK		PINMUX_PIN(PIN_PB30, 1, 1)
+#define PIN_PB30__FLEXCOM3_IO3		PINMUX_PIN(PIN_PB30, 2, 2)
+#define PIN_PB30__FLEXCOM0_IO6		PINMUX_PIN(PIN_PB30, 3, 2)
+#define PIN_PB30__TIOB3			PINMUX_PIN(PIN_PB30, 4, 1)
+#define PIN_PB30__PWMH0			PINMUX_PIN(PIN_PB30, 5, 1)
+#define PIN_PB30__FLEXCOM8_IO0		PINMUX_PIN(PIN_PB30, 6, 4)
+#define PIN_PB31			63
+#define PIN_PB31__GPIO			PINMUX_PIN(PIN_PB31, 0, 0)
+#define PIN_PB31__SDMMC1_DAT0		PINMUX_PIN(PIN_PB31, 1, 1)
+#define PIN_PB31__FLEXCOM3_IO4		PINMUX_PIN(PIN_PB31, 2, 2)
+#define PIN_PB31__FLEXCOM9_IO5		PINMUX_PIN(PIN_PB31, 3, 2)
+#define PIN_PB31__TCLK3			PINMUX_PIN(PIN_PB31, 4, 1)
+#define PIN_PB31__PWML0			PINMUX_PIN(PIN_PB31, 5, 1)
+#define PIN_PB31__FLEXCOM8_IO1		PINMUX_PIN(PIN_PB31, 6, 4)
+#define PIN_PC0				64
+#define PIN_PC0__GPIO			PINMUX_PIN(PIN_PC0, 0, 0)
+#define PIN_PC0__SDMMC1_DAT1		PINMUX_PIN(PIN_PC0, 1, 1)
+#define PIN_PC0__FLEXCOM3_IO0		PINMUX_PIN(PIN_PC0, 2, 2)
+#define PIN_PC0__TIOA4			PINMUX_PIN(PIN_PC0, 4, 1)
+#define PIN_PC0__PWML1			PINMUX_PIN(PIN_PC0, 5, 1)
+#define PIN_PC0__FLEXCOM9_IO0		PINMUX_PIN(PIN_PC0, 6, 4)
+#define PIN_PC1				65
+#define PIN_PC1__GPIO			PINMUX_PIN(PIN_PC1, 0, 0)
+#define PIN_PC1__SDMMC1_DAT2		PINMUX_PIN(PIN_PC1, 1, 1)
+#define PIN_PC1__FLEXCOM3_IO1		PINMUX_PIN(PIN_PC1, 2, 2)
+#define PIN_PC1__TIOB4			PINMUX_PIN(PIN_PC1, 4, 1)
+#define PIN_PC1__PWMH1			PINMUX_PIN(PIN_PC1, 5, 1)
+#define PIN_PC1__FLEXCOM9_IO1		PINMUX_PIN(PIN_PC1, 6, 4)
+#define PIN_PC2				66
+#define PIN_PC2__GPIO			PINMUX_PIN(PIN_PC2, 0, 0)
+#define PIN_PC2__SDMMC1_DAT3		PINMUX_PIN(PIN_PC2, 1, 1)
+#define PIN_PC2__FLEXCOM4_IO0		PINMUX_PIN(PIN_PC2, 2, 2)
+#define PIN_PC2__TCLK4			PINMUX_PIN(PIN_PC2, 4, 1)
+#define PIN_PC2__PWML2			PINMUX_PIN(PIN_PC2, 5, 1)
+#define PIN_PC2__FLEXCOM10_IO0		PINMUX_PIN(PIN_PC2, 6, 4)
+#define PIN_PC3				67
+#define PIN_PC3__GPIO			PINMUX_PIN(PIN_PC3, 0, 0)
+#define PIN_PC3__SDMMC1_WP		PINMUX_PIN(PIN_PC3, 1, 1)
+#define PIN_PC3__FLEXCOM4_IO1		PINMUX_PIN(PIN_PC3, 2, 2)
+#define PIN_PC3__TIOA5			PINMUX_PIN(PIN_PC3, 4, 1)
+#define PIN_PC3__PWMH2			PINMUX_PIN(PIN_PC3, 5, 1)
+#define PIN_PC3__FLEXCOM10_IO1		PINMUX_PIN(PIN_PC3, 6, 4)
+#define PIN_PC4				68
+#define PIN_PC4__GPIO			PINMUX_PIN(PIN_PC4, 0, 0)
+#define PIN_PC4__SDMMC1_CD		PINMUX_PIN(PIN_PC4, 1, 1)
+#define PIN_PC4__FLEXCOM4_IO2		PINMUX_PIN(PIN_PC4, 2, 2)
+#define PIN_PC4__FLEXCOM9_IO6		PINMUX_PIN(PIN_PC4, 3, 2)
+#define PIN_PC4__TIOB5			PINMUX_PIN(PIN_PC4, 4, 1)
+#define PIN_PC4__PWML3			PINMUX_PIN(PIN_PC4, 5, 1)
+#define PIN_PC4__FLEXCOM11_IO0		PINMUX_PIN(PIN_PC4, 6, 4)
+#define PIN_PC5				69
+#define PIN_PC5__GPIO			PINMUX_PIN(PIN_PC5, 0, 0)
+#define PIN_PC5__SDMMC1_1V8SEL		PINMUX_PIN(PIN_PC5, 1, 1)
+#define PIN_PC5__FLEXCOM4_IO3		PINMUX_PIN(PIN_PC5, 2, 2)
+#define PIN_PC5__FLEXCOM6_IO5		PINMUX_PIN(PIN_PC5, 3, 2)
+#define PIN_PC5__TCLK5			PINMUX_PIN(PIN_PC5, 4, 1)
+#define PIN_PC5__PWMH3			PINMUX_PIN(PIN_PC5, 5, 1)
+#define PIN_PC5__FLEXCOM11_IO1		PINMUX_PIN(PIN_PC5, 6, 4)
+#define PIN_PC6				70
+#define PIN_PC6__GPIO			PINMUX_PIN(PIN_PC6, 0, 0)
+#define PIN_PC6__FLEXCOM4_IO4		PINMUX_PIN(PIN_PC6, 2, 2)
+#define PIN_PC6__FLEXCOM6_IO6		PINMUX_PIN(PIN_PC6, 3, 2)
+#define PIN_PC7				71
+#define PIN_PC7__GPIO			PINMUX_PIN(PIN_PC7, 0, 0)
+#define PIN_PC7__I2SMCC0_DIN0		PINMUX_PIN(PIN_PC7, 1, 1)
+#define PIN_PC7__FLEXCOM7_IO0		PINMUX_PIN(PIN_PC7, 2, 2)
+#define PIN_PC8				72
+#define PIN_PC8__GPIO			PINMUX_PIN(PIN_PC8, 0, 0)
+#define PIN_PC8__I2SMCC0_DIN1		PINMUX_PIN(PIN_PC8, 1, 1)
+#define PIN_PC8__FLEXCOM7_IO1		PINMUX_PIN(PIN_PC8, 2, 2)
+#define PIN_PC9				73
+#define PIN_PC9__GPIO			PINMUX_PIN(PIN_PC9, 0, 0)
+#define PIN_PC9__I2SMCC0_DOUT3		PINMUX_PIN(PIN_PC9, 1, 1)
+#define PIN_PC9__FLEXCOM7_IO2		PINMUX_PIN(PIN_PC9, 2, 2)
+#define PIN_PC9__FLEXCOM1_IO0		PINMUX_PIN(PIN_PC9, 6, 4)
+#define PIN_PC10			74
+#define PIN_PC10__GPIO			PINMUX_PIN(PIN_PC10, 0, 0)
+#define PIN_PC10__I2SMCC0_DOUT2		PINMUX_PIN(PIN_PC10, 1, 1)
+#define PIN_PC10__FLEXCOM7_IO3		PINMUX_PIN(PIN_PC10, 2, 2)
+#define PIN_PC10__FLEXCOM1_IO1		PINMUX_PIN(PIN_PC10, 6, 4)
+#define PIN_PC11			75
+#define PIN_PC11__GPIO			PINMUX_PIN(PIN_PC11, 0, 0)
+#define PIN_PC11__I2SMCC1_CK		PINMUX_PIN(PIN_PC11, 1, 1)
+#define PIN_PC11__FLEXCOM7_IO4		PINMUX_PIN(PIN_PC11, 2, 2)
+#define PIN_PC11__FLEXCOM2_IO0		PINMUX_PIN(PIN_PC11, 6, 4)
+#define PIN_PC12			76
+#define PIN_PC12__GPIO			PINMUX_PIN(PIN_PC12, 0, 0)
+#define PIN_PC12__I2SMCC1_WS		PINMUX_PIN(PIN_PC12, 1, 1)
+#define PIN_PC12__FLEXCOM8_IO2		PINMUX_PIN(PIN_PC12, 2, 2)
+#define PIN_PC12__FLEXCOM2_IO1		PINMUX_PIN(PIN_PC12, 6, 4)
+#define PIN_PC13			77
+#define PIN_PC13__GPIO			PINMUX_PIN(PIN_PC13, 0, 0)
+#define PIN_PC13__I2SMCC1_MCK		PINMUX_PIN(PIN_PC13, 1, 1)
+#define PIN_PC13__FLEXCOM8_IO1		PINMUX_PIN(PIN_PC13, 2, 2)
+#define PIN_PC13__FLEXCOM3_IO0		PINMUX_PIN(PIN_PC13, 6, 4)
+#define PIN_PC14			78
+#define PIN_PC14__GPIO			PINMUX_PIN(PIN_PC14, 0, 0)
+#define PIN_PC14__I2SMCC1_DOUT0		PINMUX_PIN(PIN_PC14, 1, 1)
+#define PIN_PC14__FLEXCOM8_IO0		PINMUX_PIN(PIN_PC14, 2, 2)
+#define PIN_PC14__FLEXCOM3_IO1		PINMUX_PIN(PIN_PC14, 6, 4)
+#define PIN_PC15			79
+#define PIN_PC15__GPIO			PINMUX_PIN(PIN_PC15, 0, 0)
+#define PIN_PC15__I2SMCC1_DOUT1		PINMUX_PIN(PIN_PC15, 1, 1)
+#define PIN_PC15__FLEXCOM8_IO3		PINMUX_PIN(PIN_PC15, 2, 2)
+#define PIN_PC15__FLEXCOM4_IO0		PINMUX_PIN(PIN_PC15, 6, 4)
+#define PIN_PC16			80
+#define PIN_PC16__GPIO			PINMUX_PIN(PIN_PC16, 0, 0)
+#define PIN_PC16__I2SMCC1_DOUT2		PINMUX_PIN(PIN_PC16, 1, 1)
+#define PIN_PC16__FLEXCOM8_IO4		PINMUX_PIN(PIN_PC16, 2, 2)
+#define PIN_PC16__FLEXCOM3_IO1		PINMUX_PIN(PIN_PC16, 6, 4)
+#define PIN_PC17			81
+#define PIN_PC17__GPIO			PINMUX_PIN(PIN_PC17, 0, 0)
+#define PIN_PC17__I2SMCC1_DOUT3		PINMUX_PIN(PIN_PC17, 1, 1)
+#define PIN_PC17__EXT_IRQ0		PINMUX_PIN(PIN_PC17, 2, 3)
+#define PIN_PC17__FLEXCOM5_IO0		PINMUX_PIN(PIN_PC17, 6, 4)
+#define PIN_PC18			82
+#define PIN_PC18__GPIO			PINMUX_PIN(PIN_PC18, 0, 0)
+#define PIN_PC18__I2SMCC1_DIN0		PINMUX_PIN(PIN_PC18, 1, 1)
+#define PIN_PC18__FLEXCOM9_IO0		PINMUX_PIN(PIN_PC18, 2, 2)
+#define PIN_PC18__FLEXCOM5_IO1		PINMUX_PIN(PIN_PC18, 6, 4)
+#define PIN_PC19			83
+#define PIN_PC19__GPIO			PINMUX_PIN(PIN_PC19, 0, 0)
+#define PIN_PC19__I2SMCC1_DIN1		PINMUX_PIN(PIN_PC19, 1, 1)
+#define PIN_PC19__FLEXCOM9_IO1		PINMUX_PIN(PIN_PC19, 2, 2)
+#define PIN_PC19__FLEXCOM6_IO0		PINMUX_PIN(PIN_PC19, 6, 4)
+#define PIN_PC20			84
+#define PIN_PC20__GPIO			PINMUX_PIN(PIN_PC20, 0, 0)
+#define PIN_PC20__I2SMCC1_DIN2		PINMUX_PIN(PIN_PC20, 1, 1)
+#define PIN_PC20__FLEXCOM9_IO4		PINMUX_PIN(PIN_PC20, 2, 2)
+#define PIN_PC20__FLEXCOM6_IO1		PINMUX_PIN(PIN_PC20, 6, 4)
+#define PIN_PC21			85
+#define PIN_PC21__GPIO			PINMUX_PIN(PIN_PC21, 0, 0)
+#define PIN_PC21__I2SMCC1_DIN3		PINMUX_PIN(PIN_PC21, 1, 1)
+#define PIN_PC21__FLEXCOM9_IO2		PINMUX_PIN(PIN_PC21, 2, 2)
+#define PIN_PC21__D3			PINMUX_PIN(PIN_PC21, 4, 2)
+#define PIN_PC21__FLEXCOM6_IO0		PINMUX_PIN(PIN_PC21, 6, 5)
+#define PIN_PC22			86
+#define PIN_PC22__GPIO			PINMUX_PIN(PIN_PC22, 0, 0)
+#define PIN_PC22__I2SMCC0_DIN2		PINMUX_PIN(PIN_PC22, 1, 1)
+#define PIN_PC22__FLEXCOM9_IO3		PINMUX_PIN(PIN_PC22, 2, 2)
+#define PIN_PC22__D4			PINMUX_PIN(PIN_PC22, 4, 2)
+#define PIN_PC22__FLEXCOM6_IO1		PINMUX_PIN(PIN_PC22, 6, 5)
+#define PIN_PC23			87
+#define PIN_PC23__GPIO			PINMUX_PIN(PIN_PC23, 0, 0)
+#define PIN_PC23__I2SMCC0_DIN3		PINMUX_PIN(PIN_PC23, 1, 1)
+#define PIN_PC23__FLEXCOM0_IO5		PINMUX_PIN(PIN_PC23, 2, 3)
+#define PIN_PC23__D5			PINMUX_PIN(PIN_PC23, 4, 2)
+#define PIN_PC23__FLEXCOM7_IO0		PINMUX_PIN(PIN_PC23, 6, 5)
+#define PIN_PC24			88
+#define PIN_PC24__GPIO			PINMUX_PIN(PIN_PC24, 0, 0)
+#define PIN_PC24__FLEXCOM0_IO6		PINMUX_PIN(PIN_PC24, 2, 3)
+#define PIN_PC24__EXT_IRQ1		PINMUX_PIN(PIN_PC24, 3, 3)
+#define PIN_PC24__D6			PINMUX_PIN(PIN_PC24, 4, 2)
+#define PIN_PC24__FLEXCOM7_IO1		PINMUX_PIN(PIN_PC24, 6, 5)
+#define PIN_PC25			89
+#define PIN_PC25__GPIO			PINMUX_PIN(PIN_PC25, 0, 0)
+#define PIN_PC25__NTRST			PINMUX_PIN(PIN_PC25, 1, 1)
+#define PIN_PC26			90
+#define PIN_PC26__GPIO			PINMUX_PIN(PIN_PC26, 0, 0)
+#define PIN_PC26__TCK_SWCLK		PINMUX_PIN(PIN_PC26, 1, 1)
+#define PIN_PC27			91
+#define PIN_PC27__GPIO			PINMUX_PIN(PIN_PC27, 0, 0)
+#define PIN_PC27__TMS_SWDIO		PINMUX_PIN(PIN_PC27, 1, 1)
+#define PIN_PC28			92
+#define PIN_PC28__GPIO			PINMUX_PIN(PIN_PC28, 0, 0)
+#define PIN_PC28__TDI			PINMUX_PIN(PIN_PC28, 1, 1)
+#define PIN_PC29			93
+#define PIN_PC29__GPIO			PINMUX_PIN(PIN_PC29, 0, 0)
+#define PIN_PC29__TDO			PINMUX_PIN(PIN_PC29, 1, 1)
+#define PIN_PC30			94
+#define PIN_PC30__GPIO			PINMUX_PIN(PIN_PC30, 0, 0)
+#define PIN_PC30__FLEXCOM10_IO0		PINMUX_PIN(PIN_PC30, 2, 2)
+#define PIN_PC31			95
+#define PIN_PC31__GPIO			PINMUX_PIN(PIN_PC31, 0, 0)
+#define PIN_PC31__FLEXCOM10_IO1		PINMUX_PIN(PIN_PC31, 2, 2)
+#define PIN_PD0				96
+#define PIN_PD0__GPIO			PINMUX_PIN(PIN_PD0, 0, 0)
+#define PIN_PD0__FLEXCOM11_IO0		PINMUX_PIN(PIN_PD0, 2, 2)
+#define PIN_PD1				97
+#define PIN_PD1__GPIO			PINMUX_PIN(PIN_PD1, 0, 0)
+#define PIN_PD1__FLEXCOM11_IO1		PINMUX_PIN(PIN_PD1, 2, 2)
+#define PIN_PD2				98
+#define PIN_PD2__GPIO			PINMUX_PIN(PIN_PD2, 0, 0)
+#define PIN_PD2__SDMMC2_RSTN		PINMUX_PIN(PIN_PD2, 1, 1)
+#define PIN_PD2__PCK0			PINMUX_PIN(PIN_PD2, 2, 2)
+#define PIN_PD2__CANTX4			PINMUX_PIN(PIN_PD2, 3, 1)
+#define PIN_PD2__D7			PINMUX_PIN(PIN_PD2, 4, 2)
+#define PIN_PD2__TIOA0			PINMUX_PIN(PIN_PD2, 5, 2)
+#define PIN_PD2__FLEXCOM8_IO0		PINMUX_PIN(PIN_PD2, 6, 5)
+#define PIN_PD3				99
+#define PIN_PD3__GPIO			PINMUX_PIN(PIN_PD3, 0, 0)
+#define PIN_PD3__SDMMC2_CMD		PINMUX_PIN(PIN_PD3, 1, 1)
+#define PIN_PD3__FLEXCOM0_IO0		PINMUX_PIN(PIN_PD3, 2, 2)
+#define PIN_PD3__CANRX4			PINMUX_PIN(PIN_PD3, 3, 1)
+#define PIN_PD3__NANDRDY		PINMUX_PIN(PIN_PD3, 4, 2)
+#define PIN_PD3__TIOB0			PINMUX_PIN(PIN_PD3, 5, 2)
+#define PIN_PD3__FLEXCOM8_IO1		PINMUX_PIN(PIN_PD3, 6, 5)
+#define PIN_PD4				100
+#define PIN_PD4__GPIO			PINMUX_PIN(PIN_PD4, 0, 0)
+#define PIN_PD4__SDMMC2_CK		PINMUX_PIN(PIN_PD4, 1, 1)
+#define PIN_PD4__FLEXCOM0_IO1		PINMUX_PIN(PIN_PD4, 2, 2)
+#define PIN_PD4__CANTX5			PINMUX_PIN(PIN_PD4, 3, 1)
+#define PIN_PD4__NCS3_NANDCS		PINMUX_PIN(PIN_PD4, 4, 2)
+#define PIN_PD4__TCLK0			PINMUX_PIN(PIN_PD4, 5, 2)
+#define PIN_PD4__FLEXCOM9_IO0		PINMUX_PIN(PIN_PD4, 6, 5)
+#define PIN_PD5				101
+#define PIN_PD5__GPIO			PINMUX_PIN(PIN_PD5, 0, 0)
+#define PIN_PD5__SDMMC2_DAT0		PINMUX_PIN(PIN_PD5, 1, 1)
+#define PIN_PD5__FLEXCOM0_IO2		PINMUX_PIN(PIN_PD5, 2, 2)
+#define PIN_PD5__CANRX5			PINMUX_PIN(PIN_PD5, 3, 1)
+#define PIN_PD5__NWE_NWR0_NANDWE	PINMUX_PIN(PIN_PD5, 4, 2)
+#define PIN_PD5__TIOA1			PINMUX_PIN(PIN_PD5, 5, 2)
+#define PIN_PD5__FLEXCOM9_IO1		PINMUX_PIN(PIN_PD5, 6, 5)
+#define PIN_PD6				102
+#define PIN_PD6__GPIO			PINMUX_PIN(PIN_PD6, 0, 0)
+#define PIN_PD6__SDMMC2_DAT1		PINMUX_PIN(PIN_PD6, 1, 1)
+#define PIN_PD6__FLEXCOM0_IO3		PINMUX_PIN(PIN_PD6, 2, 2)
+#define PIN_PD6__SPDIF_RX		PINMUX_PIN(PIN_PD6, 3, 3)
+#define PIN_PD6__NRD_NANDOE		PINMUX_PIN(PIN_PD6, 4, 2)
+#define PIN_PD6__TIOB1			PINMUX_PIN(PIN_PD6, 5, 2)
+#define PIN_PD6__FLEXCOM10_IO0		PINMUX_PIN(PIN_PD6, 6, 5)
+#define PIN_PD7				103
+#define PIN_PD7__GPIO			PINMUX_PIN(PIN_PD7, 0, 0)
+#define PIN_PD7__SDMMC2_DAT2		PINMUX_PIN(PIN_PD7, 1, 1)
+#define PIN_PD7__FLEXCOM0_IO4		PINMUX_PIN(PIN_PD7, 2, 2)
+#define PIN_PD7__SPDIF_TX		PINMUX_PIN(PIN_PD7, 2, 2)
+#define PIN_PD7__A21_NANDALE		PINMUX_PIN(PIN_PD7, 4, 2)
+#define PIN_PD7__TCLK1			PINMUX_PIN(PIN_PD7, 5, 2)
+#define PIN_PD7__FLEXCOM10_IO1		PINMUX_PIN(PIN_PD7, 6, 5)
+#define PIN_PD8				104
+#define PIN_PD8__GPIO			PINMUX_PIN(PIN_PD8, 0, 0)
+#define PIN_PD8__SDMMC2_DAT3		PINMUX_PIN(PIN_PD8, 1, 1)
+#define PIN_PD8__I2SMCC0_DIN0		PINMUX_PIN(PIN_PD8, 3, 1)
+#define PIN_PD8__A22_NANDCLE		PINMUX_PIN(PIN_PD8, 4, 2)
+#define PIN_PD8__TIOA2			PINMUX_PIN(PIN_PD8, 5, 2)
+#define PIN_PD8__FLEXCOM11_IO0		PINMUX_PIN(PIN_PD8, 6, 5)
+#define PIN_PD9				105
+#define PIN_PD9__GPIO			PINMUX_PIN(PIN_PD9, 0, 0)
+#define PIN_PD9__SDMMC2_WP		PINMUX_PIN(PIN_PD9, 1, 1)
+#define PIN_PD9__I2SMCC0_DIN1		PINMUX_PIN(PIN_PD9, 3, 2)
+#define PIN_PD9__D0			PINMUX_PIN(PIN_PD9, 4, 2)
+#define PIN_PD9__TIOB2			PINMUX_PIN(PIN_PD9, 5, 2)
+#define PIN_PD9__FLEXCOM11_IO1		PINMUX_PIN(PIN_PD9, 6, 5)
+#define PIN_PD10			106
+#define PIN_PD10__GPIO			PINMUX_PIN(PIN_PD10, 0, 0)
+#define PIN_PD10__SDMMC2_CD		PINMUX_PIN(PIN_PD10, 1, 1)
+#define PIN_PD10__PCK6			PINMUX_PIN(PIN_PD10, 2, 2)
+#define PIN_PD10__I2SMCC0_DIN2		PINMUX_PIN(PIN_PD10, 3, 2)
+#define PIN_PD10__D1			PINMUX_PIN(PIN_PD10, 4, 2)
+#define PIN_PD10__TCLK2			PINMUX_PIN(PIN_PD10, 5, 2)
+#define PIN_PD10__FLEXCOM0_IO0		PINMUX_PIN(PIN_PD10, 6, 3)
+#define PIN_PD11			107
+#define PIN_PD11__GPIO			PINMUX_PIN(PIN_PD11, 0, 0)
+#define PIN_PD11__SDMMC2_1V8SEL		PINMUX_PIN(PIN_PD11, 1, 1)
+#define PIN_PD11__PCK7			PINMUX_PIN(PIN_PD11, 2, 2)
+#define PIN_PD11__I2SMCC0_DIN3		PINMUX_PIN(PIN_PD11, 3, 2)
+#define PIN_PD11__D2			PINMUX_PIN(PIN_PD11, 4, 2)
+#define PIN_PD11__TIOA3			PINMUX_PIN(PIN_PD11, 5, 2)
+#define PIN_PD11__FLEXCOM0_IO1		PINMUX_PIN(PIN_PD11, 6, 3)
+#define PIN_PD12			108
+#define PIN_PD12__GPIO			PINMUX_PIN(PIN_PD12, 0, 0)
+#define PIN_PD12__PCK1			PINMUX_PIN(PIN_PD12, 1, 2)
+#define PIN_PD12__FLEXCOM1_IO0		PINMUX_PIN(PIN_PD12, 2, 2)
+#define PIN_PD12__CANTX0		PINMUX_PIN(PIN_PD12, 4, 2)
+#define PIN_PD12__TIOB3			PINMUX_PIN(PIN_PD12, 5, 2)
+#define PIN_PD13			109
+#define PIN_PD13__GPIO			PINMUX_PIN(PIN_PD13, 0, 0)
+#define PIN_PD13__I2SMCC0_CK		PINMUX_PIN(PIN_PD13, 1, 2)
+#define PIN_PD13__FLEXCOM1_IO1		PINMUX_PIN(PIN_PD13, 2, 2)
+#define PIN_PD13__PWML0			PINMUX_PIN(PIN_PD13, 3, 4)
+#define PIN_PD13__CANRX0		PINMUX_PIN(PIN_PD13, 4, 2)
+#define PIN_PD13__TCLK3			PINMUX_PIN(PIN_PD13, 5, 2)
+#define PIN_PD14			110
+#define PIN_PD14__GPIO			PINMUX_PIN(PIN_PD14, 0, 0)
+#define PIN_PD14__I2SMCC0_MCK		PINMUX_PIN(PIN_PD14, 1, 2)
+#define PIN_PD14__FLEXCOM1_IO2		PINMUX_PIN(PIN_PD14, 2, 2)
+#define PIN_PD14__PWMH0			PINMUX_PIN(PIN_PD14, 3, 4)
+#define PIN_PD14__CANTX1		PINMUX_PIN(PIN_PD14, 4, 2)
+#define PIN_PD14__TIOA4			PINMUX_PIN(PIN_PD14, 5, 2)
+#define PIN_PD14__FLEXCOM2_IO0		PINMUX_PIN(PIN_PD14, 6, 5)
+#define PIN_PD15			111
+#define PIN_PD15__GPIO			PINMUX_PIN(PIN_PD15, 0, 0)
+#define PIN_PD15__I2SMCC0_WS		PINMUX_PIN(PIN_PD15, 1, 2)
+#define PIN_PD15__FLEXCOM1_IO3		PINMUX_PIN(PIN_PD15, 2, 2)
+#define PIN_PD15__PWML1			PINMUX_PIN(PIN_PD15, 3, 4)
+#define PIN_PD15__CANRX1		PINMUX_PIN(PIN_PD15, 4, 2)
+#define PIN_PD15__TIOB4			PINMUX_PIN(PIN_PD15, 5, 2)
+#define PIN_PD15__FLEXCOM2_IO1		PINMUX_PIN(PIN_PD15, 6, 5)
+#define PIN_PD16			112
+#define PIN_PD16__GPIO			PINMUX_PIN(PIN_PD16, 0, 0)
+#define PIN_PD16__I2SMCC0_DOUT0		PINMUX_PIN(PIN_PD16, 1, 2)
+#define PIN_PD16__FLEXCOM1_IO4		PINMUX_PIN(PIN_PD16, 2, 2)
+#define PIN_PD16__PWMH1			PINMUX_PIN(PIN_PD16, 3, 4)
+#define PIN_PD16__CANTX2		PINMUX_PIN(PIN_PD16, 4, 2)
+#define PIN_PD16__TCLK4			PINMUX_PIN(PIN_PD16, 5, 2)
+#define PIN_PD16__FLEXCOM3_IO0		PINMUX_PIN(PIN_PD16, 6, 5)
+#define PIN_PD17			113
+#define PIN_PD17__GPIO			PINMUX_PIN(PIN_PD17, 0, 0)
+#define PIN_PD17__I2SMCC0_DOUT1		PINMUX_PIN(PIN_PD17, 1, 2)
+#define PIN_PD17__FLEXCOM2_IO0		PINMUX_PIN(PIN_PD17, 2, 2)
+#define PIN_PD17__PWML2			PINMUX_PIN(PIN_PD17, 3, 4)
+#define PIN_PD17__CANRX2		PINMUX_PIN(PIN_PD17, 4, 2)
+#define PIN_PD17__TIOA5			PINMUX_PIN(PIN_PD17, 5, 2)
+#define PIN_PD17__FLEXCOM3_IO1		PINMUX_PIN(PIN_PD17, 6, 5)
+#define PIN_PD18			114
+#define PIN_PD18__GPIO			PINMUX_PIN(PIN_PD18, 0, 0)
+#define PIN_PD18__I2SMCC0_DOUT2		PINMUX_PIN(PIN_PD18, 1, 2)
+#define PIN_PD18__FLEXCOM2_IO1		PINMUX_PIN(PIN_PD18, 2, 2)
+#define PIN_PD18__PWMH2			PINMUX_PIN(PIN_PD18, 3, 4)
+#define PIN_PD18__CANTX3		PINMUX_PIN(PIN_PD18, 4, 2)
+#define PIN_PD18__TIOB5			PINMUX_PIN(PIN_PD18, 5, 2)
+#define PIN_PD18__FLEXCOM4_IO0		PINMUX_PIN(PIN_PD18, 6, 5)
+#define PIN_PD19			115
+#define PIN_PD19__GPIO			PINMUX_PIN(PIN_PD19, 0, 0)
+#define PIN_PD19__I2SMCC0_DOUT3		PINMUX_PIN(PIN_PD19, 1, 2)
+#define PIN_PD19__FLEXCOM2_IO2		PINMUX_PIN(PIN_PD19, 2, 2)
+#define PIN_PD19__PWML3			PINMUX_PIN(PIN_PD19, 3, 4)
+#define PIN_PD19__CANRX3		PINMUX_PIN(PIN_PD19, 4, 2)
+#define PIN_PD19__TCLK5			PINMUX_PIN(PIN_PD19, 5, 2)
+#define PIN_PD19__FLEXCOM4_IO1		PINMUX_PIN(PIN_PD19, 6, 5)
+#define PIN_PD20			116
+#define PIN_PD20__GPIO			PINMUX_PIN(PIN_PD20, 0, 0)
+#define PIN_PD20__PCK0			PINMUX_PIN(PIN_PD20, 1, 3)
+#define PIN_PD20__FLEXCOM2_IO3		PINMUX_PIN(PIN_PD20, 2, 2)
+#define PIN_PD20__PWMH3			PINMUX_PIN(PIN_PD20, 3, 4)
+#define PIN_PD20__CANTX4		PINMUX_PIN(PIN_PD20, 4, 2)
+#define PIN_PD20__FLEXCOM5_IO0		PINMUX_PIN(PIN_PD20, 6, 5)
+#define PIN_PD21			117
+#define PIN_PD21__GPIO			PINMUX_PIN(PIN_PD21, 0, 0)
+#define PIN_PD21__PCK1			PINMUX_PIN(PIN_PD21, 1, 3)
+#define PIN_PD21__FLEXCOM2_IO4		PINMUX_PIN(PIN_PD21, 2, 2)
+#define PIN_PD21__CANRX4		PINMUX_PIN(PIN_PD21, 4, 2)
+#define PIN_PD21__FLEXCOM5_IO1		PINMUX_PIN(PIN_PD21, 6, 5)
+#define PIN_PD21__G1_TXEN		PINMUX_PIN(PIN_PD21, 7, 1)
+#define PIN_PD22			118
+#define PIN_PD22__GPIO			PINMUX_PIN(PIN_PD22, 0, 0)
+#define PIN_PD22__PDMC0_CLK		PINMUX_PIN(PIN_PD22, 1, 2)
+#define PIN_PD22__PWMEXTRG0		PINMUX_PIN(PIN_PD22, 3, 4)
+#define PIN_PD22__RD1			PINMUX_PIN(PIN_PD22, 4, 2)
+#define PIN_PD22__CANTX5		PINMUX_PIN(PIN_PD22, 6, 2)
+#define PIN_PD22__G1_TX0		PINMUX_PIN(PIN_PD22, 7, 1)
+#define PIN_PD23			119
+#define PIN_PD23__GPIO			PINMUX_PIN(PIN_PD23, 0, 0)
+#define PIN_PD23__PDMC0_DS0		PINMUX_PIN(PIN_PD23, 1, 2)
+#define PIN_PD23__PWMEXTRG1		PINMUX_PIN(PIN_PD23, 3, 4)
+#define PIN_PD23__RF1			PINMUX_PIN(PIN_PD23, 4, 2)
+#define PIN_PD23__ISC_MCK		PINMUX_PIN(PIN_PD23, 5, 2)
+#define PIN_PD23__CANRX5		PINMUX_PIN(PIN_PD23, 6, 2)
+#define PIN_PD23__G1_TX1		PINMUX_PIN(PIN_PD23, 7, 1)
+#define PIN_PD24			120
+#define PIN_PD24__GPIO			PINMUX_PIN(PIN_PD24, 0, 0)
+#define PIN_PD24__PDMC0_DS1		PINMUX_PIN(PIN_PD24, 1, 2)
+#define PIN_PD24__PWMFI0		PINMUX_PIN(PIN_PD24, 3, 4)
+#define PIN_PD24__RK1			PINMUX_PIN(PIN_PD24, 4, 2)
+#define PIN_PD24__ISC_D0		PINMUX_PIN(PIN_PD24, 5, 2)
+#define PIN_PD24__G1_RXDV		PINMUX_PIN(PIN_PD24, 7, 1)
+#define PIN_PD25			121
+#define PIN_PD25__GPIO			PINMUX_PIN(PIN_PD25, 0, 0)
+#define PIN_PD25__PDMC1_CLK		PINMUX_PIN(PIN_PD25, 1, 2)
+#define PIN_PD25__FLEXCOM5_IO0		PINMUX_PIN(PIN_PD25, 2, 2)
+#define PIN_PD25__PWMFI1		PINMUX_PIN(PIN_PD25, 3, 4)
+#define PIN_PD25__TD1			PINMUX_PIN(PIN_PD25, 4, 2)
+#define PIN_PD25__ISC_D1		PINMUX_PIN(PIN_PD25, 5, 2)
+#define PIN_PD25__G1_RX0		PINMUX_PIN(PIN_PD25, 7, 1)
+#define PIN_PD26			122
+#define PIN_PD26__GPIO			PINMUX_PIN(PIN_PD26, 0, 0)
+#define PIN_PD26__PDMC1_DS0		PINMUX_PIN(PIN_PD26, 1, 2)
+#define PIN_PD26__FLEXCOM5_IO1		PINMUX_PIN(PIN_PD26, 2, 2)
+#define PIN_PD26__ADTRG			PINMUX_PIN(PIN_PD26, 3, 3)
+#define PIN_PD26__TF1			PINMUX_PIN(PIN_PD26, 4, 2)
+#define PIN_PD26__ISC_D2		PINMUX_PIN(PIN_PD26, 5, 2)
+#define PIN_PD26__G1_RX1		PINMUX_PIN(PIN_PD26, 7, 1)
+#define PIN_PD27			123
+#define PIN_PD27__GPIO			PINMUX_PIN(PIN_PD27, 0, 0)
+#define PIN_PD27__PDMC1_DS1		PINMUX_PIN(PIN_PD27, 1, 2)
+#define PIN_PD27__FLEXCOM5_IO2		PINMUX_PIN(PIN_PD27, 2, 2)
+#define PIN_PD27__TIOA0			PINMUX_PIN(PIN_PD27, 3, 3)
+#define PIN_PD27__TK1			PINMUX_PIN(PIN_PD27, 4, 2)
+#define PIN_PD27__ISC_D3		PINMUX_PIN(PIN_PD27, 5, 2)
+#define PIN_PD27__G1_RXER		PINMUX_PIN(PIN_PD27, 7, 1)
+#define PIN_PD28			124
+#define PIN_PD28__GPIO			PINMUX_PIN(PIN_PD28, 0, 0)
+#define PIN_PD28__RD0			PINMUX_PIN(PIN_PD28, 1, 2)
+#define PIN_PD28__FLEXCOM5_IO3		PINMUX_PIN(PIN_PD28, 2, 2)
+#define PIN_PD28__TIOB0			PINMUX_PIN(PIN_PD28, 3, 3)
+#define PIN_PD28__I2SMCC1_CK		PINMUX_PIN(PIN_PD28, 4, 2)
+#define PIN_PD28__ISC_D4		PINMUX_PIN(PIN_PD28, 5, 2)
+#define PIN_PD28__PWML3			PINMUX_PIN(PIN_PD28, 6, 5)
+#define PIN_PD28__G1_MDC		PINMUX_PIN(PIN_PD28, 7, 1)
+#define PIN_PD29			125
+#define PIN_PD29__GPIO			PINMUX_PIN(PIN_PD29, 0, 0)
+#define PIN_PD29__RF0			PINMUX_PIN(PIN_PD29, 1, 2)
+#define PIN_PD29__FLEXCOM5_IO4		PINMUX_PIN(PIN_PD29, 2, 2)
+#define PIN_PD29__TCLK0			PINMUX_PIN(PIN_PD29, 3, 3)
+#define PIN_PD29__I2SMCC1_WS		PINMUX_PIN(PIN_PD29, 4, 2)
+#define PIN_PD29__ISC_D5		PINMUX_PIN(PIN_PD29, 5, 2)
+#define PIN_PD29__PWMH3			PINMUX_PIN(PIN_PD29, 6, 5)
+#define PIN_PD29__G1_MDIO		PINMUX_PIN(PIN_PD29, 7, 1)
+#define PIN_PD30			126
+#define PIN_PD30__GPIO			PINMUX_PIN(PIN_PD30, 0, 0)
+#define PIN_PD30__RK0			PINMUX_PIN(PIN_PD30, 1, 2)
+#define PIN_PD30__FLEXCOM6_IO0		PINMUX_PIN(PIN_PD30, 2, 2)
+#define PIN_PD30__TIOA1			PINMUX_PIN(PIN_PD30, 3, 3)
+#define PIN_PD30__I2SMCC1_MCK		PINMUX_PIN(PIN_PD30, 4, 2)
+#define PIN_PD30__ISC_D6		PINMUX_PIN(PIN_PD30, 5, 2)
+#define PIN_PD30__PWMEXTRG0		PINMUX_PIN(PIN_PD30, 6, 5)
+#define PIN_PD30__G1_TXCK		PINMUX_PIN(PIN_PD30, 7, 1)
+#define PIN_PD31			127
+#define PIN_PD31__GPIO			PINMUX_PIN(PIN_PD31, 0, 0)
+#define PIN_PD31__TD0			PINMUX_PIN(PIN_PD31, 1, 2)
+#define PIN_PD31__FLEXCOM6_IO1		PINMUX_PIN(PIN_PD31, 2, 2)
+#define PIN_PD31__TIOB1			PINMUX_PIN(PIN_PD31, 3, 3)
+#define PIN_PD31__I2SMCC1_DOUT0		PINMUX_PIN(PIN_PD31, 4, 2)
+#define PIN_PD31__ISC_D7		PINMUX_PIN(PIN_PD31, 5, 2)
+#define PIN_PD31__PWM_EXTRG1		PINMUX_PIN(PIN_PD31, 6, 5)
+#define PIN_PD31__G1_TX2		PINMUX_PIN(PIN_PD31, 7, 1)
+#define PIN_PE0				128
+#define PIN_PE0__GPIO			PINMUX_PIN(PIN_PE0, 0, 0)
+#define PIN_PE0__TF0			PINMUX_PIN(PIN_PE0, 1, 2)
+#define PIN_PE0__FLEXCOM6_IO2		PINMUX_PIN(PIN_PE0, 2, 2)
+#define PIN_PE0__TCLK1			PINMUX_PIN(PIN_PE0, 3, 3)
+#define PIN_PE0__I2SMCC1_DOUT1		PINMUX_PIN(PIN_PE0, 4, 2)
+#define PIN_PE0__ISC_HSYNC		PINMUX_PIN(PIN_PE0, 5, 2)
+#define PIN_PE0__PWMFI0			PINMUX_PIN(PIN_PE0, 6, 5)
+#define PIN_PE0__G1_TX3			PINMUX_PIN(PIN_PE0, 7, 1)
+#define PIN_PE1				129
+#define PIN_PE1__GPIO			PINMUX_PIN(PIN_PE1, 0, 0)
+#define PIN_PE1__TK0			PINMUX_PIN(PIN_PE1, 1, 2)
+#define PIN_PE1__FLEXCOM6_IO3		PINMUX_PIN(PIN_PE1, 2, 2)
+#define PIN_PE1__TIOA2			PINMUX_PIN(PIN_PE1, 3, 3)
+#define PIN_PE1__I2SMCC1_DOUT2		PINMUX_PIN(PIN_PE1, 4, 2)
+#define PIN_PE1__ISC_VSYNC		PINMUX_PIN(PIN_PE1, 5, 2)
+#define PIN_PE1__PWMFI1			PINMUX_PIN(PIN_PE1, 6, 5)
+#define PIN_PE1__G1_RX2			PINMUX_PIN(PIN_PE1, 7, 1)
+#define PIN_PE2				130
+#define PIN_PE2__GPIO			PINMUX_PIN(PIN_PE2, 0, 0)
+#define PIN_PE2__PWML0			PINMUX_PIN(PIN_PE2, 1, 5)
+#define PIN_PE2__FLEXCOM6_IO4		PINMUX_PIN(PIN_PE2, 2, 2)
+#define PIN_PE2__TIOB2			PINMUX_PIN(PIN_PE2, 3, 3)
+#define PIN_PE2__I2SMCC1_DOUT3		PINMUX_PIN(PIN_PE2, 4, 2)
+#define PIN_PE2__ISC_FIELD		PINMUX_PIN(PIN_PE2, 5, 2)
+#define PIN_PE2__G1_RX3			PINMUX_PIN(PIN_PE2, 7, 1)
+#define PIN_PE3				131
+#define PIN_PE3__GPIO			PINMUX_PIN(PIN_PE3, 0, 0)
+#define PIN_PE3__PWMH0			PINMUX_PIN(PIN_PE3, 1, 5)
+#define PIN_PE3__FLEXCOM0_IO0		PINMUX_PIN(PIN_PE3, 2, 4)
+#define PIN_PE3__TCLK2			PINMUX_PIN(PIN_PE3, 3, 3)
+#define PIN_PE3__I2SMCC1_DIN0		PINMUX_PIN(PIN_PE3, 4, 2)
+#define PIN_PE3__ISC_PCK		PINMUX_PIN(PIN_PE3, 5, 2)
+#define PIN_PE3__G1_RXCK		PINMUX_PIN(PIN_PE3, 7, 1)
+#define PIN_PE4				132
+#define PIN_PE4__GPIO			PINMUX_PIN(PIN_PE4, 0, 0)
+#define PIN_PE4__PWML1			PINMUX_PIN(PIN_PE4, 1, 5)
+#define PIN_PE4__FLEXCOM0_IO1		PINMUX_PIN(PIN_PE4, 2, 4)
+#define PIN_PE4__TIOA3			PINMUX_PIN(PIN_PE4, 3, 3)
+#define PIN_PE4__I2SMCC1_DIN1		PINMUX_PIN(PIN_PE4, 4, 2)
+#define PIN_PE4__ISC_D8			PINMUX_PIN(PIN_PE4, 5, 2)
+#define PIN_PE4__G1_TXER		PINMUX_PIN(PIN_PE4, 7, 1)
+#define PIN_PE5				133
+#define PIN_PE5__GPIO			PINMUX_PIN(PIN_PE5, 0, 0)
+#define PIN_PE5__PWMH1			PINMUX_PIN(PIN_PE5, 1, 5)
+#define PIN_PE5__FLEXCOM0_IO2		PINMUX_PIN(PIN_PE5, 2, 4)
+#define PIN_PE5__TIOB3			PINMUX_PIN(PIN_PE5, 3, 3)
+#define PIN_PE5__I2SMCC1_DIN2		PINMUX_PIN(PIN_PE5, 4, 2)
+#define PIN_PE5__ISC_D9			PINMUX_PIN(PIN_PE5, 5, 2)
+#define PIN_PE5__G1_COL			PINMUX_PIN(PIN_PE5, 7, 1)
+#define PIN_PE6				134
+#define PIN_PE6__GPIO			PINMUX_PIN(PIN_PE6, 0, 0)
+#define PIN_PE6__PWML2			PINMUX_PIN(PIN_PE6, 1, 5)
+#define PIN_PE6__FLEXCOM0_IO3		PINMUX_PIN(PIN_PE6, 2, 4)
+#define PIN_PE6__TCLK3			PINMUX_PIN(PIN_PE6, 3, 3)
+#define PIN_PE6__I2SMCC1_DIN3		PINMUX_PIN(PIN_PE6, 4, 2)
+#define PIN_PE6__ISC_D10		PINMUX_PIN(PIN_PE6, 5, 2)
+#define PIN_PE6__G1_CRS			PINMUX_PIN(PIN_PE6, 7, 1)
+#define PIN_PE7				135
+#define PIN_PE7__GPIO			PINMUX_PIN(PIN_PE7, 0, 0)
+#define PIN_PE7__PWMH2			PINMUX_PIN(PIN_PE7, 1, 5)
+#define PIN_PE7__FLEXCOM0_IO4		PINMUX_PIN(PIN_PE7, 2, 4)
+#define PIN_PE7__TIOA4			PINMUX_PIN(PIN_PE7, 3, 3)
+#define PIN_PE7__ISC_D11		PINMUX_PIN(PIN_PE7, 5, 2)
+#define PIN_PE7__G1_TSUCOMP		PINMUX_PIN(PIN_PE7, 7, 1)
diff --git a/arch/arm/boot/dts/microchip/sama7g5.dtsi b/arch/arm/boot/dts/microchip/sama7g5.dtsi
new file mode 100644
index 000000000000..269e0a3ca269
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sama7g5.dtsi
@@ -0,0 +1,1016 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ *  sama7g5.dtsi - Device Tree Include file for SAMA7G5 family SoC
+ *
+ *  Copyright (C) 2020 Microchip Technology, Inc. and its subsidiaries
+ *
+ *  Author: Eugen Hristev <eugen.hristev@microchip.com>
+ *  Author: Claudiu Beznea <claudiu.beznea@microchip.com>
+ *
+ */
+
+#include <dt-bindings/iio/adc/at91-sama5d2_adc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/nvmem/microchip,sama7g5-otpc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	model = "Microchip SAMA7G5 family SoC";
+	compatible = "microchip,sama7g5";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_CPUPLL>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+	};
+
+	cpu_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-90000000 {
+			opp-hz = /bits/ 64 <90000000>;
+			opp-microvolt = <1050000 1050000 1225000>;
+			clock-latency-ns = <320000>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <1050000 1050000 1225000>;
+			clock-latency-ns = <320000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1050000 1050000 1225000>;
+			clock-latency-ns = <320000>;
+			opp-suspend;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1150000 1125000 1225000>;
+			clock-latency-ns = <320000>;
+		};
+
+		opp-1000000002 {
+			opp-hz = /bits/ 64 <1000000002>;
+			opp-microvolt = <1250000 1225000 1300000>;
+			clock-latency-ns = <320000>;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&thermal_sensor>;
+
+			trips {
+				cpu_normal: cpu-alert0 {
+					temperature = <90000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				cpu_hot: cpu-alert1 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_normal>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	clocks {
+		slow_xtal: slow_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		main_xtal: main_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		usb_clk: usb_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <48000000>;
+		};
+	};
+
+	vddout25: fixed-regulator-vddout25 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VDDOUT25";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-boot-on;
+		status = "disabled";
+	};
+
+	ns_sram: sram@100000 {
+		compatible = "mmio-sram";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x100000 0x20000>;
+		ranges;
+	};
+
+	thermal_sensor: thermal-sensor {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc AT91_SAMA7G5_ADC_TEMP_CHANNEL>;
+		io-channel-names = "sensor-channel";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		nfc_sram: sram@600000 {
+			compatible = "mmio-sram";
+			no-memory-wc;
+			reg = <0x00600000 0x2400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x00600000 0x2400>;
+		};
+
+		nfc_io: nfc-io@10000000 {
+			compatible = "atmel,sama5d3-nfc-io", "syscon";
+			reg = <0x10000000 0x8000000>;
+		};
+
+		ebi: ebi@40000000 {
+			compatible = "atmel,sama5d3-ebi";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			atmel,smc = <&hsmc>;
+			reg = <0x40000000 0x20000000>;
+			ranges = <0x0 0x0 0x40000000 0x8000000
+				  0x1 0x0 0x48000000 0x8000000
+				  0x2 0x0 0x50000000 0x8000000
+				  0x3 0x0 0x58000000 0x8000000>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK1>;
+			status = "disabled";
+
+			nand_controller: nand-controller {
+				compatible = "atmel,sama5d3-nand-controller";
+				atmel,nfc-sram = <&nfc_sram>;
+				atmel,nfc-io = <&nfc_io>;
+				ecc-engine = <&pmecc>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				ranges;
+				status = "disabled";
+			};
+		};
+
+		securam: sram@e0000000 {
+			compatible = "microchip,sama7g5-securam", "atmel,sama5d2-securam", "mmio-sram";
+			reg = <0xe0000000 0x4000>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xe0000000 0x4000>;
+			no-memory-wc;
+		};
+
+		secumod: secumod@e0004000 {
+			compatible = "microchip,sama7g5-secumod", "atmel,sama5d2-secumod", "syscon";
+			reg = <0xe0004000 0x4000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		sfrbu: sfr@e0008000 {
+			compatible = "microchip,sama7g5-sfrbu", "atmel,sama5d2-sfrbu", "syscon";
+			reg = <0xe0008000 0x20>;
+		};
+
+		pioA: pinctrl@e0014000 {
+			compatible = "microchip,sama7g5-pinctrl";
+			reg = <0xe0014000 0x800>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+		};
+
+		pmc: clock-controller@e0018000 {
+			compatible = "microchip,sama7g5-pmc", "syscon";
+			reg = <0xe0018000 0x200>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			#clock-cells = <2>;
+			clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+			clock-names = "td_slck", "md_slck", "main_xtal";
+		};
+
+		reset_controller: reset-controller@e001d000 {
+			compatible = "microchip,sama7g5-rstc";
+			reg = <0xe001d000 0xc>, <0xe001d0e4 0x4>;
+			#reset-cells = <1>;
+			clocks = <&clk32k 0>;
+		};
+
+		shdwc: poweroff@e001d010 {
+			compatible = "microchip,sama7g5-shdwc", "syscon";
+			reg = <0xe001d010 0x10>;
+			clocks = <&clk32k 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			atmel,wakeup-rtc-timer;
+			atmel,wakeup-rtt-timer;
+			status = "disabled";
+		};
+
+		rtt: rtc@e001d020 {
+			compatible = "microchip,sama7g5-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
+			reg = <0xe001d020 0x30>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 0>;
+		};
+
+		clk32k: clock-controller@e001d050 {
+			compatible = "microchip,sama7g5-sckc", "microchip,sam9x60-sckc";
+			reg = <0xe001d050 0x4>;
+			clocks = <&slow_xtal>;
+			#clock-cells = <1>;
+		};
+
+		gpbr: gpbr@e001d060 {
+			compatible = "microchip,sama7g5-gpbr", "syscon";
+			reg = <0xe001d060 0x48>;
+		};
+
+		rtc: rtc@e001d0a8 {
+			compatible = "microchip,sama7g5-rtc", "microchip,sam9x60-rtc";
+			reg = <0xe001d0a8 0x30>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 1>;
+		};
+
+		ps_wdt: watchdog@e001d180 {
+			compatible = "microchip,sama7g5-wdt";
+			reg = <0xe001d180 0x24>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 0>;
+		};
+
+		chipid@e0020000 {
+			compatible = "microchip,sama7g5-chipid";
+			reg = <0xe0020000 0x8>;
+		};
+
+		tcb1: timer@e0800000 {
+			compatible = "atmel,sama5d2-tcb", "simple-mfd", "syscon";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe0800000 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 91>, <&pmc PMC_TYPE_PERIPHERAL 92>, <&pmc PMC_TYPE_PERIPHERAL 93>, <&clk32k 1>;
+			clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
+		};
+
+		hsmc: hsmc@e0808000 {
+			compatible = "atmel,sama5d2-smc", "syscon", "simple-mfd";
+			reg = <0xe0808000 0x1000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pmecc: ecc-engine@e0808070 {
+				compatible = "atmel,sama5d2-pmecc";
+				reg = <0xe0808070 0x490>,
+				      <0xe0808500 0x200>;
+			};
+		};
+
+		qspi0: spi@e080c000 {
+			compatible = "microchip,sama7g5-ospi";
+			reg = <0xe080c000 0x400>, <0x20000000 0x10000000>;
+			reg-names = "qspi_base", "qspi_mmap";
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(41)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(40)>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 78>, <&pmc PMC_TYPE_GCK 78>;
+			clock-names = "pclk", "gclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		qspi1: spi@e0810000 {
+			compatible = "microchip,sama7g5-qspi";
+			reg = <0xe0810000 0x400>, <0x30000000 0x10000000>;
+			reg-names = "qspi_base", "qspi_mmap";
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(43)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(42)>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 79>, <&pmc PMC_TYPE_GCK 79>;
+			clock-names = "pclk", "gclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		can0: can@e0828000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0828000 0x100>, <0x100000 0x7800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 61>, <&pmc PMC_TYPE_GCK 61>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 61>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@e082c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe082c000 0x100>, <0x100000 0xbc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 62>, <&pmc PMC_TYPE_GCK 62>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 62>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can2: can@e0830000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0830000 0x100>, <0x100000 0x10000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 63>, <&pmc PMC_TYPE_GCK 63>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 63>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0xbc00 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can3: can@e0834000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0834000 0x100>, <0x110000 0x4400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 64>, <&pmc PMC_TYPE_GCK 64>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 64>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can4: can@e0838000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0838000 0x100>, <0x110000 0x8800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 65>, <&pmc PMC_TYPE_GCK 65>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 65>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x4400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can5: can@e083c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe083c000 0x100>, <0x110000 0xcc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 66>, <&pmc PMC_TYPE_GCK 66>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 66>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x8800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		adc: adc@e1000000 {
+			compatible = "microchip,sama7g5-adc";
+			reg = <0xe1000000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clock-rates = <100000000>;
+			clock-names = "adc_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(0)>;
+			dma-names = "rx";
+			atmel,min-sample-rate-hz = <200000>;
+			atmel,max-sample-rate-hz = <20000000>;
+			atmel,startup-time-ms = <4>;
+			#io-channel-cells = <1>;
+			nvmem-cells = <&temperature_calib>;
+			nvmem-cell-names = "temperature_calib";
+			status = "disabled";
+		};
+
+		sdmmc0: mmc@e1204000 {
+			compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0xe1204000 0x4000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 80>, <&pmc PMC_TYPE_GCK 80>;
+			clock-names = "hclock", "multclk";
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clocks = <&pmc PMC_TYPE_GCK 80>;
+			assigned-clock-rates = <200000000>;
+			microchip,sdcal-inverted;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@e1208000 {
+			compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0xe1208000 0x4000>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 81>, <&pmc PMC_TYPE_GCK 81>;
+			clock-names = "hclock", "multclk";
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clocks = <&pmc PMC_TYPE_GCK 81>;
+			assigned-clock-rates = <200000000>;
+			microchip,sdcal-inverted;
+			status = "disabled";
+		};
+
+		sdmmc2: mmc@e120c000 {
+			compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0xe120c000 0x4000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 82>, <&pmc PMC_TYPE_GCK 82>;
+			clock-names = "hclock", "multclk";
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clocks = <&pmc PMC_TYPE_GCK 82>;
+			assigned-clock-rates = <200000000>;
+			microchip,sdcal-inverted;
+			status = "disabled";
+		};
+
+		csi2dc: csi2dc@e1404000 {
+			compatible = "microchip,sama7g5-csi2dc";
+			reg = <0xe1404000 0x500>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&xisc>;
+			clock-names = "pclk", "scck";
+			assigned-clocks = <&xisc>;
+			assigned-clock-rates = <266000000>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					csi2dc_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					csi2dc_out: endpoint {
+						bus-width = <14>;
+						hsync-active = <1>;
+						vsync-active = <1>;
+						remote-endpoint = <&xisc_in>;
+					};
+				};
+			};
+		};
+
+		xisc: xisc@e1408000 {
+			compatible = "microchip,sama7g5-isc";
+			reg = <0xe1408000 0x2000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 56>;
+			clock-names = "hclock";
+			#clock-cells = <0>;
+			clock-output-names = "isc-mck";
+			status = "disabled";
+
+			port {
+				xisc_in: endpoint {
+					bus-type = <5>; /* Parallel */
+					bus-width = <14>;
+					hsync-active = <1>;
+					vsync-active = <1>;
+					remote-endpoint = <&csi2dc_out>;
+				};
+			};
+		};
+
+		pwm: pwm@e1604000 {
+			compatible = "microchip,sama7g5-pwm", "atmel,sama5d2-pwm";
+			reg = <0xe1604000 0x4000>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+			#pwm-cells = <3>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 77>;
+			status = "disabled";
+		};
+
+		pdmc0: sound@e1608000 {
+			compatible = "microchip,sama7g5-pdmc";
+			reg = <0xe1608000 0x1000>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			#sound-dai-cells = <0>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(37)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 68>, <&pmc PMC_TYPE_GCK 68>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		pdmc1: sound@e160c000 {
+			compatible = "microchip,sama7g5-pdmc";
+			reg = <0xe160c000 0x1000>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			#sound-dai-cells = <0>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(38)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 69>, <&pmc PMC_TYPE_GCK 69>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		spdifrx: spdifrx@e1614000 {
+			#sound-dai-cells = <0>;
+			compatible = "microchip,sama7g5-spdifrx";
+			reg = <0xe1614000 0x4000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(49)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 84>, <&pmc PMC_TYPE_GCK 84>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		spdiftx: spdiftx@e1618000 {
+			#sound-dai-cells = <0>;
+			compatible = "microchip,sama7g5-spdiftx";
+			reg = <0xe1618000 0x4000>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(50)>;
+			dma-names = "tx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 85>, <&pmc PMC_TYPE_GCK 85>;
+			clock-names = "pclk", "gclk";
+		};
+
+		i2s0: i2s@e161c000 {
+			compatible = "microchip,sama7g5-i2smcc";
+			#sound-dai-cells = <0>;
+			reg = <0xe161c000 0x4000>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(34)>, <&dma0 AT91_XDMAC_DT_PERID(33)>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 57>, <&pmc PMC_TYPE_GCK 57>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		i2s1: i2s@e1620000 {
+			compatible = "microchip,sama7g5-i2smcc";
+			#sound-dai-cells = <0>;
+			reg = <0xe1620000 0x4000>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(36)>, <&dma0 AT91_XDMAC_DT_PERID(35)>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		eic: interrupt-controller@e1628000 {
+			compatible = "microchip,sama7g5-eic";
+			reg = <0xe1628000 0xec>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+			clock-names = "pclk";
+			status = "disabled";
+		};
+
+		pit64b0: timer@e1800000 {
+			compatible = "microchip,sama7g5-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xe1800000 0x4000>;
+			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 70>, <&pmc PMC_TYPE_GCK 70>;
+			clock-names = "pclk", "gclk";
+		};
+
+		pit64b1: timer@e1804000 {
+			compatible = "microchip,sama7g5-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xe1804000 0x4000>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 71>, <&pmc PMC_TYPE_GCK 71>;
+			clock-names = "pclk", "gclk";
+		};
+
+		aes: crypto@e1810000 {
+			compatible = "atmel,at91sam9g46-aes";
+			reg = <0xe1810000 0x100>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 27>;
+			clock-names = "aes_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(1)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+			dma-names = "tx", "rx";
+		};
+
+		sha: crypto@e1814000 {
+			compatible = "atmel,at91sam9g46-sha";
+			reg = <0xe1814000 0x100>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 83>;
+			clock-names = "sha_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(48)>;
+			dma-names = "tx";
+		};
+
+		flx0: flexcom@e1818000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe1818000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe1818000 0x800>;
+			status = "disabled";
+
+			uart0: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>,
+					<&dma1 AT91_XDMAC_DT_PERID(5)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e181c000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe181c000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe181c000 0x800>;
+			status = "disabled";
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+					<&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e1824000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe1824000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe1824000 0x800>;
+			status = "disabled";
+
+			uart3: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(12)>,
+					<&dma1 AT91_XDMAC_DT_PERID(11)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "disabled";
+			};
+		};
+
+		trng: rng@e2010000 {
+			compatible = "microchip,sama7g5-trng", "atmel,at91sam9g45-trng";
+			reg = <0xe2010000 0x100>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 97>;
+			status = "disabled";
+		};
+
+		tdes: crypto@e2014000 {
+			compatible = "atmel,at91sam9g46-tdes";
+			reg = <0xe2014000 0x100>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 96>;
+			clock-names = "tdes_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(54)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(53)>;
+			dma-names = "tx", "rx";
+		};
+
+		flx4: flexcom@e2018000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe2018000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe2018000 0x800>;
+			status = "disabled";
+
+			uart4: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>,
+					<&dma1 AT91_XDMAC_DT_PERID(13)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx7: flexcom@e2024000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe2024000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe2024000 0x800>;
+			status = "disabled";
+
+			uart7: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>,
+					<&dma1 AT91_XDMAC_DT_PERID(19)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		gmac0: ethernet@e2800000 {
+			compatible = "microchip,sama7g5-gem";
+			reg = <0xe2800000 0x1000>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_GCK 51>, <&pmc PMC_TYPE_GCK 53>;
+			clock-names = "pclk", "hclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 51>;
+			assigned-clock-rates = <125000000>;
+			status = "disabled";
+		};
+
+		gmac1: ethernet@e2804000 {
+			compatible = "microchip,sama7g5-emac";
+			reg = <0xe2804000 0x1000>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 52>, <&pmc PMC_TYPE_PERIPHERAL 52>;
+			clock-names = "pclk", "hclk";
+			status = "disabled";
+		};
+
+		dma0: dma-controller@e2808000 {
+			compatible = "microchip,sama7g5-dma";
+			reg = <0xe2808000 0x1000>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+			clock-names = "dma_clk";
+			status = "disabled";
+		};
+
+		dma1: dma-controller@e280c000 {
+			compatible = "microchip,sama7g5-dma";
+			reg = <0xe280c000 0x1000>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+			clock-names = "dma_clk";
+			status = "disabled";
+		};
+
+		/* Place dma2 here despite it's address */
+		dma2: dma-controller@e1200000 {
+			compatible = "microchip,sama7g5-dma";
+			reg = <0xe1200000 0x1000>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 24>;
+			clock-names = "dma_clk";
+			dma-requests = <0>;
+			status = "disabled";
+		};
+
+		tcb0: timer@e2814000 {
+			compatible = "atmel,sama5d2-tcb", "simple-mfd", "syscon";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe2814000 0x100>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 88>, <&pmc PMC_TYPE_PERIPHERAL 89>, <&pmc PMC_TYPE_PERIPHERAL 90>, <&clk32k 1>;
+			clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
+		};
+
+		flx8: flexcom@e2818000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe2818000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe2818000 0x800>;
+			status = "disabled";
+
+			i2c8: i2c@600 {
+				compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+					<&dma0 AT91_XDMAC_DT_PERID(21)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		flx9: flexcom@e281c000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe281c000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe281c000 0x800>;
+			status = "disabled";
+
+			i2c9: i2c@600 {
+				compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+					<&dma0 AT91_XDMAC_DT_PERID(23)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		flx11: flexcom@e2824000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe2824000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 49>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe2824000 0x800>;
+			status = "disabled";
+
+			spi11: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 49>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(28)>,
+					    <&dma0 AT91_XDMAC_DT_PERID(27)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		uddrc: uddrc@e3800000 {
+			compatible = "microchip,sama7g5-uddrc";
+			reg = <0xe3800000 0x4000>;
+		};
+
+		ddr3phy: ddr3phy@e3804000 {
+			compatible = "microchip,sama7g5-ddr3phy";
+			reg = <0xe3804000 0x1000>;
+		};
+
+		otpc: efuse@e8c00000 {
+			compatible = "microchip,sama7g5-otpc", "syscon";
+			reg = <0xe8c00000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			temperature_calib: calib@1 {
+				reg = <OTP_PKT(1) 76>;
+			};
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0xe8c11000 0x1000>,
+				<0xe8c12000 0x2000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tny_a9260.dts b/arch/arm/boot/dts/microchip/tny_a9260.dts
index ef6d586ce887..ef6d586ce887 100644
--- a/arch/arm/boot/dts/tny_a9260.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9260.dts
diff --git a/arch/arm/boot/dts/tny_a9260_common.dtsi b/arch/arm/boot/dts/microchip/tny_a9260_common.dtsi
index dd6957b20772..70e5635c78ed 100644
--- a/arch/arm/boot/dts/tny_a9260_common.dtsi
+++ b/arch/arm/boot/dts/microchip/tny_a9260_common.dtsi
@@ -10,7 +10,7 @@
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock6 rw rootfstype=ubifs";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
diff --git a/arch/arm/boot/dts/tny_a9263.dts b/arch/arm/boot/dts/microchip/tny_a9263.dts
index 2820635952e3..62b7d9f9a926 100644
--- a/arch/arm/boot/dts/tny_a9263.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9263.dts
@@ -15,7 +15,7 @@
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
diff --git a/arch/arm/boot/dts/tny_a9g20.dts b/arch/arm/boot/dts/microchip/tny_a9g20.dts
index 118d766a1265..118d766a1265 100644
--- a/arch/arm/boot/dts/tny_a9g20.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9g20.dts
diff --git a/arch/arm/boot/dts/usb_a9260.dts b/arch/arm/boot/dts/microchip/usb_a9260.dts
index ec8cd86b260d..66f8da89007d 100644
--- a/arch/arm/boot/dts/usb_a9260.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9260.dts
@@ -16,13 +16,13 @@
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
 	ahb {
 		apb {
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
diff --git a/arch/arm/boot/dts/usb_a9260_common.dtsi b/arch/arm/boot/dts/microchip/usb_a9260_common.dtsi
index 8744b5f6f792..8744b5f6f792 100644
--- a/arch/arm/boot/dts/usb_a9260_common.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9260_common.dtsi
diff --git a/arch/arm/boot/dts/usb_a9263.dts b/arch/arm/boot/dts/microchip/usb_a9263.dts
index e7a705fddda9..45745915b2e1 100644
--- a/arch/arm/boot/dts/usb_a9263.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9263.dts
@@ -15,7 +15,7 @@
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
@@ -60,14 +60,14 @@
 			spi0: spi@fffa4000 {
 				cs-gpios = <&pioB 15 GPIO_ACTIVE_HIGH>;
 				status = "okay";
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					reg = <0>;
 					spi-max-frequency = <15000000>;
 				};
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
diff --git a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi b/arch/arm/boot/dts/microchip/usb_a9g20-dab-mmx.dtsi
index 08d58081201a..08d58081201a 100644
--- a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9g20-dab-mmx.dtsi
diff --git a/arch/arm/boot/dts/usb_a9g20.dts b/arch/arm/boot/dts/microchip/usb_a9g20.dts
index 2f667b083e81..2f667b083e81 100644
--- a/arch/arm/boot/dts/usb_a9g20.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9g20.dts
diff --git a/arch/arm/boot/dts/usb_a9g20_common.dtsi b/arch/arm/boot/dts/microchip/usb_a9g20_common.dtsi
index adbe75024739..7d10b36db1ee 100644
--- a/arch/arm/boot/dts/usb_a9g20_common.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9g20_common.dtsi
@@ -14,7 +14,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@20000000 {
 		reg = <0x20000000 0x4000000>;
 	};
 
diff --git a/arch/arm/boot/dts/usb_a9g20_lpw.dts b/arch/arm/boot/dts/microchip/usb_a9g20_lpw.dts
index f65712015d40..f65712015d40 100644
--- a/arch/arm/boot/dts/usb_a9g20_lpw.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9g20_lpw.dts
diff --git a/arch/arm/boot/dts/mmp2-brownstone.dts b/arch/arm/boot/dts/mmp2-brownstone.dts
deleted file mode 100644
index aaedc4c742ea..000000000000
--- a/arch/arm/boot/dts/mmp2-brownstone.dts
+++ /dev/null
@@ -1,194 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2012 Marvell Technology Group Ltd.
- *  Author: Haojian Zhuang <haojian.zhuang@marvell.com>
- */
-
-/dts-v1/;
-#include "mmp2.dtsi"
-
-/ {
-	model = "Marvell MMP2 Brownstone Development Board";
-	compatible = "mrvl,mmp2-brownstone", "mrvl,mmp2";
-
-	chosen {
-		bootargs = "console=ttyS2,38400 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on";
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x08000000>;
-	};
-
-	soc {
-		apb@d4000000 {
-			uart3: uart@d4018000 {
-				status = "okay";
-			};
-			twsi1: i2c@d4011000 {
-				status = "okay";
-				pmic: max8925@3c {
-					compatible = "maxium,max8925";
-					reg = <0x3c>;
-					interrupts = <1>;
-					interrupt-parent = <&intcmux4>;
-					interrupt-controller;
-					#interrupt-cells = <1>;
-					maxim,tsc-irq = <0>;
-
-					regulators {
-						SDV1 {
-							regulator-min-microvolt = <637500>;
-							regulator-max-microvolt = <1425000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						SDV2 {
-							regulator-min-microvolt = <650000>;
-							regulator-max-microvolt = <2225000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						SDV3 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO1 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO2 {
-							regulator-min-microvolt = <650000>;
-							regulator-max-microvolt = <2250000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO3 {
-							regulator-min-microvolt = <650000>;
-							regulator-max-microvolt = <2250000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO4 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO5 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO6 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO7 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO8 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO9 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO10 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-						};
-						LDO11 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO12 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO13 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO14 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO15 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO16 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO17 {
-							regulator-min-microvolt = <650000>;
-							regulator-max-microvolt = <2250000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO18 {
-							regulator-min-microvolt = <650000>;
-							regulator-max-microvolt = <2250000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO19 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO20 {
-							regulator-min-microvolt = <750000>;
-							regulator-max-microvolt = <3900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-					};
-					backlight {
-						maxim,max8925-dual-string = <0>;
-					};
-					charger {
-						batt-detect = <0>;
-						topoff-threshold = <1>;
-						fast-charge = <7>;
-						no-temp-support = <0>;
-						no-insert-detect = <0>;
-					};
-				};
-			};
-			rtc: rtc@d4010000 {
-				status = "okay";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/mmp3-dell-ariel.dts
deleted file mode 100644
index c1947b5a688d..000000000000
--- a/arch/arm/boot/dts/mmp3-dell-ariel.dts
+++ /dev/null
@@ -1,94 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
- *
- * Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
- */
-
-/dts-v1/;
-#include "mmp3.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
-	model = "Dell Ariel";
-	compatible = "dell,wyse-ariel", "marvell,mmp3";
-
-	aliases {
-		serial2 = &uart3;
-	};
-
-	chosen {
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
-		ranges;
-		bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
-	};
-
-	memory@0 {
-		linux,usable-memory = <0x0 0x7f600000>;
-		available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
-		reg = <0x0 0x80000000>;
-		device_type = "memory";
-	};
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&rtc {
-	status = "okay";
-};
-
-&usb_otg0 {
-	status = "okay";
-};
-
-&usb_otg_phy0 {
-	status = "okay";
-};
-
-&mmc3 {
-	status = "okay";
-	max-frequency = <50000000>;
-	status = "okay";
-	bus-width = <8>;
-	non-removable;
-	cap-mmc-highspeed;
-};
-
-&twsi1 {
-	status = "okay";
-
-	rtc@68 {
-		compatible = "dallas,ds1338";
-		reg = <0x68>;
-		status = "okay";
-	};
-};
-
-&twsi3 {
-	status = "okay";
-};
-
-&twsi4 {
-	status = "okay";
-};
-
-&ssp3 {
-	status = "okay";
-	cs-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
-
-	firmware-flash@0 {
-		compatible = "st,m25p80", "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <40000000>;
-		m25p,fast-read;
-	};
-};
-
-&ssp4 {
-	cs-gpios = <&gpio 56 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
deleted file mode 100644
index da6b107da84a..000000000000
--- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi
+++ /dev/null
@@ -1,786 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/dts-v1/;
-
-#include <dt-bindings/input/input.h>
-#include "omap443x.dtsi"
-#include "motorola-cpcap-mapphone.dtsi"
-
-/ {
-	chosen {
-		stdout-path = &uart3;
-	};
-
-	aliases {
-		display0 = &lcd0;
-		display1 = &hdmi0;
-	};
-
-	/*
-	 * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
-	 * then 1023 - 1024 seems to contain mbm.
-	 */
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x3fd00000>;	/* 1021 MB */
-	};
-
-	/* Poweroff GPIO probably connected to CPCAP */
-	gpio-poweroff {
-		compatible = "gpio-poweroff";
-		pinctrl-0 = <&poweroff_gpio>;
-		pinctrl-names = "default";
-		gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;	/* gpio50 */
-	};
-
-	hdmi0: connector {
-		compatible = "hdmi-connector";
-		pinctrl-0 = <&hdmi_hpd_gpio>;
-		pinctrl-names = "default";
-		label = "hdmi";
-		type = "d";
-
-		hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;	/* gpio63 */
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_out>;
-			};
-		};
-	};
-
-	/*
-	 * HDMI 5V regulator probably sourced from battery. Let's keep
-	 * keep this as always enabled for HDMI to work until we've
-	 * figured what the encoder chip is.
-	 */
-	hdmi_regulator: regulator-hdmi {
-		compatible = "regulator-fixed";
-		regulator-name = "hdmi";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;	/* gpio59 */
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	/* FS USB Host PHY on port 1 for mdm6600 */
-	fsusb1_phy: usb-phy@1 {
-		compatible = "motorola,mapphone-mdm6600";
-		pinctrl-0 = <&usb_mdm6600_pins>;
-		pinctrl-names = "default";
-		enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
-		power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;	/* gpio_54 */
-		reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;	/* gpio_49 */
-		/* mode: gpio_148 gpio_149 */
-		motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
-				      <&gpio5 21 GPIO_ACTIVE_HIGH>;
-		/* cmd: gpio_103 gpio_104 gpio_142 */
-		motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
-				     <&gpio4 8 GPIO_ACTIVE_HIGH>,
-				     <&gpio5 14 GPIO_ACTIVE_HIGH>;
-		/* status: gpio_52 gpio_53 gpio_55 */
-		motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
-					<&gpio2 21 GPIO_ACTIVE_HIGH>,
-					<&gpio2 23 GPIO_ACTIVE_HIGH>;
-		#phy-cells = <0>;
-	};
-
-	/* HS USB host TLL nop-phy on port 2 for w3glte */
-	hsusb2_phy: usb-phy@2 {
-		compatible = "usb-nop-xceiv";
-		#phy-cells = <0>;
-	};
-
-	/* LCD regulator from sw5 source */
-	lcd_regulator: regulator-lcd {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd";
-		regulator-min-microvolt = <5050000>;
-		regulator-max-microvolt = <5050000>;
-		gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;	/* gpio96 */
-		enable-active-high;
-		vin-supply = <&sw5>;
-	};
-
-	/* This is probably coming straight from the battery.. */
-	wl12xx_vmmc: regulator-wl12xx {
-		compatible = "regulator-fixed";
-		regulator-name = "vwl1271";
-		regulator-min-microvolt = <1650000>;
-		regulator-max-microvolt = <1650000>;
-		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;	/* gpio94 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-
-		volume_down {
-			label = "Volume Down";
-			gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
-			linux,code = <KEY_VOLUMEDOWN>;
-			linux,can-disable;
-			/* Value above 7.95ms for no GPIO hardware debounce */
-			debounce-interval = <10>;
-		};
-
-		slider {
-			label = "Keypad Slide";
-			gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_KEYPAD_SLIDE>;
-			linux,can-disable;
-			/* Value above 7.95ms for no GPIO hardware debounce */
-			debounce-interval = <10>;
-		};
-	};
-
-	soundcard {
-		compatible = "audio-graph-card";
-		label = "Droid 4 Audio";
-
-		simple-graph-card,widgets =
-			"Speaker", "Earpiece",
-			"Speaker", "Loudspeaker",
-			"Headphone", "Headphone Jack",
-			"Microphone", "Internal Mic";
-
-		simple-graph-card,routing =
-			"Earpiece", "EP",
-			"Loudspeaker", "SPKR",
-			"Headphone Jack", "HSL",
-			"Headphone Jack", "HSR",
-			"MICR", "Internal Mic";
-
-		dais = <&mcbsp2_port>, <&mcbsp3_port>;
-	};
-
-	pwm8: dmtimer-pwm-8 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&vibrator_direction_pin>;
-
-		compatible = "ti,omap-dmtimer-pwm";
-		#pwm-cells = <3>;
-		ti,timers = <&timer8>;
-		ti,clock-source = <0x01>;
-	};
-
-	pwm9: dmtimer-pwm-9 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&vibrator_enable_pin>;
-
-		compatible = "ti,omap-dmtimer-pwm";
-		#pwm-cells = <3>;
-		ti,timers = <&timer9>;
-		ti,clock-source = <0x01>;
-	};
-
-	vibrator {
-		compatible = "pwm-vibrator";
-		pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
-		pwm-names = "enable", "direction";
-		direction-duty-cycle-ns = <10000000>;
-	};
-};
-
-&dss {
-	status = "okay";
-};
-
-&dsi1 {
-	status = "okay";
-	vdd-supply = <&vcsi>;
-
-	port {
-		dsi1_out_ep: endpoint {
-			remote-endpoint = <&lcd0_in>;
-			lanes = <0 1 2 3 4 5>;
-		};
-	};
-
-	lcd0: display {
-		compatible = "panel-dsi-cm";
-		label = "lcd0";
-		vddi-supply = <&lcd_regulator>;
-		reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;	/* gpio101 */
-
-		width-mm = <50>;
-		height-mm = <89>;
-
-		panel-timing {
-			clock-frequency = <0>;		/* Calculated by dsi */
-
-			hback-porch = <2>;
-			hactive = <540>;
-			hfront-porch = <0>;
-			hsync-len = <2>;
-
-			vback-porch = <1>;
-			vactive = <960>;
-			vfront-porch = <0>;
-			vsync-len = <1>;
-
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-
-		port {
-			lcd0_in: endpoint {
-				remote-endpoint = <&dsi1_out_ep>;
-			};
-		};
-	};
-};
-
-&hdmi {
-	status = "okay";
-	pinctrl-0 = <&dss_hdmi_pins>;
-	pinctrl-names = "default";
-	vdda-supply = <&vdac>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&hdmi_connector_in>;
-			lanes = <1 0 3 2 5 4 7 6>;
-		};
-	};
-};
-
-&i2c1 {
-	tmp105@48 {
-		compatible = "ti,tmp105";
-		reg = <0x48>;
-		pinctrl-0 = <&tmp105_irq>;
-		pinctrl-names = "default";
-		/* kpd_row0.gpio_178 */
-		interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
-				       &omap4_pmx_core 0x14e>;
-		interrupt-names = "irq", "wakeup";
-		wakeup-source;
-	};
-};
-
-&keypad {
-	keypad,num-rows = <8>;
-	keypad,num-columns = <8>;
-	linux,keymap = <
-
-	/* Row 1 */
-	MATRIX_KEY(0, 2, KEY_1)
-	MATRIX_KEY(0, 6, KEY_2)
-	MATRIX_KEY(2, 3, KEY_3)
-	MATRIX_KEY(0, 7, KEY_4)
-	MATRIX_KEY(0, 4, KEY_5)
-	MATRIX_KEY(5, 5, KEY_6)
-	MATRIX_KEY(0, 1, KEY_7)
-	MATRIX_KEY(0, 5, KEY_8)
-	MATRIX_KEY(0, 0, KEY_9)
-	MATRIX_KEY(1, 6, KEY_0)
-
-	/* Row 2 */
-	MATRIX_KEY(3, 4, KEY_APOSTROPHE)
-	MATRIX_KEY(7, 6, KEY_Q)
-	MATRIX_KEY(7, 7, KEY_W)
-	MATRIX_KEY(7, 2, KEY_E)
-	MATRIX_KEY(1, 0, KEY_R)
-	MATRIX_KEY(4, 4, KEY_T)
-	MATRIX_KEY(1, 2, KEY_Y)
-	MATRIX_KEY(6, 7, KEY_U)
-	MATRIX_KEY(2, 2, KEY_I)
-	MATRIX_KEY(5, 6, KEY_O)
-	MATRIX_KEY(3, 7, KEY_P)
-	MATRIX_KEY(6, 5, KEY_BACKSPACE)
-
-	/* Row 3 */
-	MATRIX_KEY(5, 4, KEY_TAB)
-	MATRIX_KEY(5, 7, KEY_A)
-	MATRIX_KEY(2, 7, KEY_S)
-	MATRIX_KEY(7, 0, KEY_D)
-	MATRIX_KEY(2, 6, KEY_F)
-	MATRIX_KEY(6, 2, KEY_G)
-	MATRIX_KEY(6, 6, KEY_H)
-	MATRIX_KEY(1, 4, KEY_J)
-	MATRIX_KEY(3, 1, KEY_K)
-	MATRIX_KEY(2, 1, KEY_L)
-	MATRIX_KEY(4, 6, KEY_ENTER)
-
-	/* Row 4 */
-	MATRIX_KEY(3, 6, KEY_LEFTSHIFT)		/* KEY_CAPSLOCK */
-	MATRIX_KEY(6, 1, KEY_Z)
-	MATRIX_KEY(7, 4, KEY_X)
-	MATRIX_KEY(5, 1, KEY_C)
-	MATRIX_KEY(1, 7, KEY_V)
-	MATRIX_KEY(2, 4, KEY_B)
-	MATRIX_KEY(4, 1, KEY_N)
-	MATRIX_KEY(1, 1, KEY_M)
-	MATRIX_KEY(3, 5, KEY_COMMA)
-	MATRIX_KEY(5, 2, KEY_DOT)
-	MATRIX_KEY(6, 3, KEY_UP)
-	MATRIX_KEY(7, 3, KEY_OK)
-
-	/* Row 5 */
-	MATRIX_KEY(2, 5, KEY_LEFTCTRL)		/* KEY_LEFTSHIFT */
-	MATRIX_KEY(4, 5, KEY_LEFTALT)		/* SYM */
-	MATRIX_KEY(6, 0, KEY_MINUS)
-	MATRIX_KEY(4, 7, KEY_EQUAL)
-	MATRIX_KEY(1, 5, KEY_SPACE)
-	MATRIX_KEY(3, 2, KEY_SLASH)
-	MATRIX_KEY(4, 3, KEY_LEFT)
-	MATRIX_KEY(5, 3, KEY_DOWN)
-	MATRIX_KEY(3, 3, KEY_RIGHT)
-
-	/* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
-	MATRIX_KEY(5, 0, KEY_VOLUMEUP)
-	>;
-};
-
-&mmc1 {
-	vmmc-supply = <&vwlan2>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;	/* gpio176 */
-};
-
-&mmc2 {
-	vmmc-supply = <&vsdio>;
-	bus-width = <8>;
-	ti,non-removable;
-};
-
-&mmc3 {
-	vmmc-supply = <&wl12xx_vmmc>;
-	/* uart2_tx.sdmmc3_dat1 pad as wakeirq */
-	interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0xde>;
-	interrupt-names = "irq", "wakeup";
-	non-removable;
-	bus-width = <4>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-	wlcore: wlcore@2 {
-		compatible = "ti,wl1285", "ti,wl1283";
-		reg = <2>;
-		/* gpio_100 with gpmc_wait2 pad as wakeirq */
-		interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
-				      <&omap4_pmx_core 0x4e>;
-		interrupt-names = "irq", "wakeup";
-		ref-clock-frequency = <26000000>;
-		tcxo-clock-frequency = <26000000>;
-	};
-};
-
-&i2c1 {
-	led-controller@38 {
-		compatible = "ti,lm3532";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x38>;
-
-		enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
-
-		ramp-up-us = <1024>;
-		ramp-down-us = <8193>;
-
-		led@0 {
-			reg = <0>;
-			led-sources = <2>;
-			ti,led-mode = <0>;
-			label = ":backlight";
-			linux,default-trigger = "backlight";
-		};
-
-		led@1 {
-			reg = <1>;
-			led-sources = <1>;
-			ti,led-mode = <0>;
-			label = ":kbd_backlight";
-		};
-	};
-};
-
-&i2c2 {
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&touchscreen_pins>;
-
-		reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
-
-		/* gpio_183 with sys_nirq2 pad as wakeup */
-		interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING>,
-				      <&omap4_pmx_core 0x160>;
-		interrupt-names = "irq", "wakeup";
-		wakeup-source;
-	};
-
-	isl29030@44 {
-		compatible = "isil,isl29030";
-		reg = <0x44>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&als_proximity_pins>;
-
-		interrupt-parent = <&gpio6>;
-		interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
-	};
-};
-
-&omap4_pmx_core {
-
-	/* hdmi_hpd.gpio_63 */
-	hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
-		>;
-	};
-
-	/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
-		>;
-	};
-
-	/* gpmc_ncs0.gpio_50 */
-	poweroff_gpio: pinmux_poweroff_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	/* kpd_row0.gpio_178 */
-	tmp105_irq: pinmux_tmp105_irq {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
-		/* gpio_60 */
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
-		>;
-	};
-
-	touchscreen_pins: pinmux_touchscreen_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	als_proximity_pins: pinmux_als_proximity_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
-		pinctrl-single,pins = <
-		/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
-		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
-
-		/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
-		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
-
-		/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
-		OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
-
-		/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
-		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
-
-		/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
-		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
-
-		/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
-		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
-
-		/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
-		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
-
-		/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
-		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
-
-		/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
-		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
-
-		/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
-		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
-
-		/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
-		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
-		>;
-	};
-
-	usb_ulpi_pins: pinmux_usb_ulpi_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x196, MUX_MODE7)
-		OMAP4_IOPAD(0x198, MUX_MODE7)
-		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
-		>;
-	};
-
-	/* usb0_otg_dp and usb0_otg_dm */
-	usb_utmi_pins: pinmux_usb_utmi_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
-		>;
-	};
-
-	/*
-	 * Note that the v3.0.8 stock userspace dynamically remuxes uart1
-	 * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
-	 * when not used. If needed, we can add rts pin remux later based
-	 * on power measurements.
-	 */
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-		/* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
-		OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
-
-		/* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
-		OMAP4_IOPAD(0x13e, MUX_MODE1)
-
-		/* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
-		OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
-
-		/* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
-		OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
-		>;
-	};
-
-	/* uart3_tx_irtx and uart3_rx_irrx */
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x196, MUX_MODE7)
-		OMAP4_IOPAD(0x198, MUX_MODE7)
-		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1ba, MUX_MODE2)
-		OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
-		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
-		>;
-	};
-
-	uart4_pins: pinmux_uart4_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)		/* uart4_rx */
-		OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)		/* uart4_tx */
-		OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)	/* uart4_cts */
-		OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)	/* uart4_rts */
-		>;
-	};
-
-	mcbsp2_pins: pinmux_mcbsp2_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_clkx */
-		OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_dr */
-		OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)	/* abe_mcbsp2_dx */
-		OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_fsx */
-		>;
-	};
-
-	mcbsp3_pins: pinmux_mcbsp3_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_dr */
-		OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)	/* abe_mcbsp3_dx */
-		OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_clkx */
-		OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_fsx */
-		>;
-	};
-
-	vibrator_direction_pin: pinmux_vibrator_direction_pin {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)	/* dmtimer8_pwm_evt (gpio_27) */
-		>;
-	};
-
-	vibrator_enable_pin: pinmux_vibrator_enable_pin {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)	/* dmtimer9_pwm_evt (gpio_28) */
-		>;
-	};
-};
-
-&omap4_pmx_wkup {
-	usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
-		/* gpio_wk0 */
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
-		>;
-	};
-};
-
-/* Configure pwm clock source for timers 8 & 9 */
-&timer8 {
-	assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_clkin_ck>;
-};
-
-&timer9 {
-	assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_clkin_ck>;
-};
-
-/*
- * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
- * uart1 wakeirq.
- */
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
-	interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0xfc>;
-};
-
-&uart3 {
-	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0x17c>;
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins>;
-
-	bluetooth {
-		compatible = "ti,wl1285-st";
-		enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
-		max-speed = <3686400>;
-	};
-};
-
-&usbhsohci {
-	phys = <&fsusb1_phy>;
-	phy-names = "usb";
-};
-
-&usbhsehci {
-	phys = <&hsusb2_phy>;
-};
-
-&usbhshost {
-	port1-mode = "ohci-phy-4pin-dpdm";
-	port2-mode = "ehci-tll";
-};
-
-/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
-&usb_otg_hs {
-	interface-type = <1>;
-	mode = <3>;
-
-	/*
-	 * Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4.
-	 * VBUS Regulator Main Characteristics". Binding uses 2 mA units.
-	 */
-	power = <150>;
-};
-
-&i2c4 {
-	ak8975: magnetometer@c {
-		compatible = "asahi-kasei,ak8975";
-		reg = <0x0c>;
-
-		vdd-supply = <&vhvio>;
-
-		interrupt-parent = <&gpio6>;
-		interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
-
-		rotation-matrix = "-1", "0", "0",
-				  "0", "1", "0",
-				  "0", "0", "-1";
-
-	};
-
-	lis3dh: accelerometer@18 {
-		compatible = "st,lis3dh-accel";
-		reg = <0x18>;
-
-		vdd-supply = <&vhvio>;
-
-		interrupt-parent = <&gpio2>;
-		interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
-
-		rotation-matrix = "0", "-1", "0",
-				  "1", "0", "0",
-				  "0", "0", "1";
-	};
-};
-
-&mcbsp2 {
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp2_pins>;
-	status = "okay";
-
-	mcbsp2_port: port {
-		cpu_dai2: endpoint {
-			dai-format = "i2s";
-			remote-endpoint = <&cpcap_audio_codec0>;
-			frame-master = <&cpcap_audio_codec0>;
-			bitclock-master = <&cpcap_audio_codec0>;
-		};
-	};
-};
-
-&mcbsp3 {
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp3_pins>;
-	status = "okay";
-
-	mcbsp3_port: port {
-		cpu_dai3: endpoint {
-			dai-format = "dsp_a";
-			frame-master = <&cpcap_audio_codec1>;
-			bitclock-master = <&cpcap_audio_codec1>;
-			remote-endpoint = <&cpcap_audio_codec1>;
-		};
-	};
-};
-
-&cpcap_audio_codec0 {
-	remote-endpoint = <&cpu_dai2>;
-};
-
-&cpcap_audio_codec1 {
-	remote-endpoint = <&cpu_dai3>;
-};
diff --git a/arch/arm/boot/dts/moxa/Makefile b/arch/arm/boot/dts/moxa/Makefile
new file mode 100644
index 000000000000..d61ce8d4e732
--- /dev/null
+++ b/arch/arm/boot/dts/moxa/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MOXART) += \
+	moxart-uc7112lx.dtb
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxa/moxart-uc7112lx.dts
index eb5291b0ee3a..e07b807b4cec 100644
--- a/arch/arm/boot/dts/moxart-uc7112lx.dts
+++ b/arch/arm/boot/dts/moxa/moxart-uc7112lx.dts
@@ -79,7 +79,7 @@
 	clocks = <&ref12>;
 };
 
-&sdhci {
+&mmc {
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxa/moxart.dtsi
index f5f070a87482..11cbea5b94d2 100644
--- a/arch/arm/boot/dts/moxart.dtsi
+++ b/arch/arm/boot/dts/moxa/moxart.dtsi
@@ -93,8 +93,8 @@
 			clock-names = "PCLK";
 		};
 
-		sdhci: sdhci@98e00000 {
-			compatible = "moxa,moxart-sdhci";
+		mmc: mmc@98e00000 {
+			compatible = "moxa,moxart-mmc";
 			reg = <0x98e00000 0x5C>;
 			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_apb>;
@@ -138,7 +138,7 @@
 			status = "disabled";
 		};
 
-		uart0: uart@98200000 {
+		uart0: serial@98200000 {
 			compatible = "ns16550a";
 			reg = <0x98200000 0x20>;
 			interrupts = <31 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/mt7623a.dtsi b/arch/arm/boot/dts/mt7623a.dtsi
deleted file mode 100644
index 0735a1fb8ad9..000000000000
--- a/arch/arm/boot/dts/mt7623a.dtsi
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (c) 2017-2018 MediaTek Inc.
- * Author: Sean Wang <sean.wang@mediatek.com>
- *
- */
-
-/dts-v1/;
-#include <dt-bindings/power/mt7623a-power.h>
-#include "mt7623.dtsi"
-
-&afe {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
-};
-
-&crypto {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
-};
-
-&eth {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
-};
-
-&nandc {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
-};
-
-&pcie {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
-};
-
-&scpsys {
-	compatible = "mediatek,mt7623a-scpsys";
-	clocks = <&topckgen CLK_TOP_ETHIF_SEL>;
-	clock-names = "ethif";
-};
-
-&usb1 {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
-};
-
-&usb2 {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
-};
diff --git a/arch/arm/boot/dts/mt8135-pinfunc.h b/arch/arm/boot/dts/mt8135-pinfunc.h
deleted file mode 100644
index ce0cb5a440eb..000000000000
--- a/arch/arm/boot/dts/mt8135-pinfunc.h
+++ /dev/null
@@ -1,1294 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (c) 2014 MediaTek Inc.
- * Author: Hongzhou.Yang <hongzhou.yang@mediatek.com>
- */
-
-#ifndef __DTS_MT8135_PINFUNC_H
-#define __DTS_MT8135_PINFUNC_H
-
-#include <dt-bindings/pinctrl/mt65xx.h>
-
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_GPIO0 (MTK_PIN_NO(0) | 0)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_MSDC0_DAT7 (MTK_PIN_NO(0) | 1)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_EINT49 (MTK_PIN_NO(0) | 2)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_I2SOUT_DAT (MTK_PIN_NO(0) | 3)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_DAC_DAT_OUT (MTK_PIN_NO(0) | 4)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_PCM1_DO (MTK_PIN_NO(0) | 5)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_SPI1_MO (MTK_PIN_NO(0) | 6)
-#define MT8135_PIN_0_MSDC0_DAT7__FUNC_NALE (MTK_PIN_NO(0) | 7)
-
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_GPIO1 (MTK_PIN_NO(1) | 0)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_MSDC0_DAT6 (MTK_PIN_NO(1) | 1)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_EINT48 (MTK_PIN_NO(1) | 2)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_I2SIN_WS (MTK_PIN_NO(1) | 3)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_DAC_WS (MTK_PIN_NO(1) | 4)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_PCM1_WS (MTK_PIN_NO(1) | 5)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_SPI1_CSN (MTK_PIN_NO(1) | 6)
-#define MT8135_PIN_1_MSDC0_DAT6__FUNC_NCLE (MTK_PIN_NO(1) | 7)
-
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_GPIO2 (MTK_PIN_NO(2) | 0)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_MSDC0_DAT5 (MTK_PIN_NO(2) | 1)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_EINT47 (MTK_PIN_NO(2) | 2)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_I2SIN_CK (MTK_PIN_NO(2) | 3)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_DAC_CK (MTK_PIN_NO(2) | 4)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_PCM1_CK (MTK_PIN_NO(2) | 5)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_SPI1_CLK (MTK_PIN_NO(2) | 6)
-#define MT8135_PIN_2_MSDC0_DAT5__FUNC_NLD4 (MTK_PIN_NO(2) | 7)
-
-#define MT8135_PIN_3_MSDC0_DAT4__FUNC_GPIO3 (MTK_PIN_NO(3) | 0)
-#define MT8135_PIN_3_MSDC0_DAT4__FUNC_MSDC0_DAT4 (MTK_PIN_NO(3) | 1)
-#define MT8135_PIN_3_MSDC0_DAT4__FUNC_EINT46 (MTK_PIN_NO(3) | 2)
-#define MT8135_PIN_3_MSDC0_DAT4__FUNC_A_FUNC_CK (MTK_PIN_NO(3) | 3)
-#define MT8135_PIN_3_MSDC0_DAT4__FUNC_LSCE1B_2X (MTK_PIN_NO(3) | 6)
-#define MT8135_PIN_3_MSDC0_DAT4__FUNC_NLD5 (MTK_PIN_NO(3) | 7)
-
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_GPIO4 (MTK_PIN_NO(4) | 0)
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_MSDC0_CMD (MTK_PIN_NO(4) | 1)
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_EINT41 (MTK_PIN_NO(4) | 2)
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_A_FUNC_DOUT_0 (MTK_PIN_NO(4) | 3)
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_USB_TEST_IO_0 (MTK_PIN_NO(4) | 5)
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_LRSTB_2X (MTK_PIN_NO(4) | 6)
-#define MT8135_PIN_4_MSDC0_CMD__FUNC_NRNB (MTK_PIN_NO(4) | 7)
-
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_GPIO5 (MTK_PIN_NO(5) | 0)
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_MSDC0_CLK (MTK_PIN_NO(5) | 1)
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_EINT40 (MTK_PIN_NO(5) | 2)
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_A_FUNC_DOUT_1 (MTK_PIN_NO(5) | 3)
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_USB_TEST_IO_1 (MTK_PIN_NO(5) | 5)
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_LPTE (MTK_PIN_NO(5) | 6)
-#define MT8135_PIN_5_MSDC0_CLK__FUNC_NREB (MTK_PIN_NO(5) | 7)
-
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_GPIO6 (MTK_PIN_NO(6) | 0)
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_MSDC0_DAT3 (MTK_PIN_NO(6) | 1)
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_EINT45 (MTK_PIN_NO(6) | 2)
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_A_FUNC_DOUT_2 (MTK_PIN_NO(6) | 3)
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_USB_TEST_IO_2 (MTK_PIN_NO(6) | 5)
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_LSCE0B_2X (MTK_PIN_NO(6) | 6)
-#define MT8135_PIN_6_MSDC0_DAT3__FUNC_NLD7 (MTK_PIN_NO(6) | 7)
-
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_GPIO7 (MTK_PIN_NO(7) | 0)
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_MSDC0_DAT2 (MTK_PIN_NO(7) | 1)
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_EINT44 (MTK_PIN_NO(7) | 2)
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_A_FUNC_DOUT_3 (MTK_PIN_NO(7) | 3)
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_USB_TEST_IO_3 (MTK_PIN_NO(7) | 5)
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_LSA0_2X (MTK_PIN_NO(7) | 6)
-#define MT8135_PIN_7_MSDC0_DAT2__FUNC_NLD14 (MTK_PIN_NO(7) | 7)
-
-#define MT8135_PIN_8_MSDC0_DAT1__FUNC_GPIO8 (MTK_PIN_NO(8) | 0)
-#define MT8135_PIN_8_MSDC0_DAT1__FUNC_MSDC0_DAT1 (MTK_PIN_NO(8) | 1)
-#define MT8135_PIN_8_MSDC0_DAT1__FUNC_EINT43 (MTK_PIN_NO(8) | 2)
-#define MT8135_PIN_8_MSDC0_DAT1__FUNC_USB_TEST_IO_4 (MTK_PIN_NO(8) | 5)
-#define MT8135_PIN_8_MSDC0_DAT1__FUNC_LSCK_2X (MTK_PIN_NO(8) | 6)
-#define MT8135_PIN_8_MSDC0_DAT1__FUNC_NLD11 (MTK_PIN_NO(8) | 7)
-
-#define MT8135_PIN_9_MSDC0_DAT0__FUNC_GPIO9 (MTK_PIN_NO(9) | 0)
-#define MT8135_PIN_9_MSDC0_DAT0__FUNC_MSDC0_DAT0 (MTK_PIN_NO(9) | 1)
-#define MT8135_PIN_9_MSDC0_DAT0__FUNC_EINT42 (MTK_PIN_NO(9) | 2)
-#define MT8135_PIN_9_MSDC0_DAT0__FUNC_USB_TEST_IO_5 (MTK_PIN_NO(9) | 5)
-#define MT8135_PIN_9_MSDC0_DAT0__FUNC_LSDA_2X (MTK_PIN_NO(9) | 6)
-
-#define MT8135_PIN_10_NCEB0__FUNC_GPIO10 (MTK_PIN_NO(10) | 0)
-#define MT8135_PIN_10_NCEB0__FUNC_NCEB0 (MTK_PIN_NO(10) | 1)
-#define MT8135_PIN_10_NCEB0__FUNC_EINT139 (MTK_PIN_NO(10) | 2)
-#define MT8135_PIN_10_NCEB0__FUNC_TESTA_OUT4 (MTK_PIN_NO(10) | 7)
-
-#define MT8135_PIN_11_NCEB1__FUNC_GPIO11 (MTK_PIN_NO(11) | 0)
-#define MT8135_PIN_11_NCEB1__FUNC_NCEB1 (MTK_PIN_NO(11) | 1)
-#define MT8135_PIN_11_NCEB1__FUNC_EINT140 (MTK_PIN_NO(11) | 2)
-#define MT8135_PIN_11_NCEB1__FUNC_USB_DRVVBUS (MTK_PIN_NO(11) | 6)
-#define MT8135_PIN_11_NCEB1__FUNC_TESTA_OUT5 (MTK_PIN_NO(11) | 7)
-
-#define MT8135_PIN_12_NRNB__FUNC_GPIO12 (MTK_PIN_NO(12) | 0)
-#define MT8135_PIN_12_NRNB__FUNC_NRNB (MTK_PIN_NO(12) | 1)
-#define MT8135_PIN_12_NRNB__FUNC_EINT141 (MTK_PIN_NO(12) | 2)
-#define MT8135_PIN_12_NRNB__FUNC_A_FUNC_DOUT_4 (MTK_PIN_NO(12) | 3)
-#define MT8135_PIN_12_NRNB__FUNC_TESTA_OUT6 (MTK_PIN_NO(12) | 7)
-
-#define MT8135_PIN_13_NCLE__FUNC_GPIO13 (MTK_PIN_NO(13) | 0)
-#define MT8135_PIN_13_NCLE__FUNC_NCLE (MTK_PIN_NO(13) | 1)
-#define MT8135_PIN_13_NCLE__FUNC_EINT142 (MTK_PIN_NO(13) | 2)
-#define MT8135_PIN_13_NCLE__FUNC_A_FUNC_DOUT_5 (MTK_PIN_NO(13) | 3)
-#define MT8135_PIN_13_NCLE__FUNC_CM2PDN_1X (MTK_PIN_NO(13) | 4)
-#define MT8135_PIN_13_NCLE__FUNC_NALE (MTK_PIN_NO(13) | 6)
-#define MT8135_PIN_13_NCLE__FUNC_TESTA_OUT7 (MTK_PIN_NO(13) | 7)
-
-#define MT8135_PIN_14_NALE__FUNC_GPIO14 (MTK_PIN_NO(14) | 0)
-#define MT8135_PIN_14_NALE__FUNC_NALE (MTK_PIN_NO(14) | 1)
-#define MT8135_PIN_14_NALE__FUNC_EINT143 (MTK_PIN_NO(14) | 2)
-#define MT8135_PIN_14_NALE__FUNC_A_FUNC_DOUT_6 (MTK_PIN_NO(14) | 3)
-#define MT8135_PIN_14_NALE__FUNC_CM2MCLK_1X (MTK_PIN_NO(14) | 4)
-#define MT8135_PIN_14_NALE__FUNC_IRDA_RXD (MTK_PIN_NO(14) | 5)
-#define MT8135_PIN_14_NALE__FUNC_NCLE (MTK_PIN_NO(14) | 6)
-#define MT8135_PIN_14_NALE__FUNC_TESTA_OUT8 (MTK_PIN_NO(14) | 7)
-
-#define MT8135_PIN_15_NREB__FUNC_GPIO15 (MTK_PIN_NO(15) | 0)
-#define MT8135_PIN_15_NREB__FUNC_NREB (MTK_PIN_NO(15) | 1)
-#define MT8135_PIN_15_NREB__FUNC_EINT144 (MTK_PIN_NO(15) | 2)
-#define MT8135_PIN_15_NREB__FUNC_A_FUNC_DOUT_7 (MTK_PIN_NO(15) | 3)
-#define MT8135_PIN_15_NREB__FUNC_CM2RST_1X (MTK_PIN_NO(15) | 4)
-#define MT8135_PIN_15_NREB__FUNC_IRDA_TXD (MTK_PIN_NO(15) | 5)
-#define MT8135_PIN_15_NREB__FUNC_TESTA_OUT9 (MTK_PIN_NO(15) | 7)
-
-#define MT8135_PIN_16_NWEB__FUNC_GPIO16 (MTK_PIN_NO(16) | 0)
-#define MT8135_PIN_16_NWEB__FUNC_NWEB (MTK_PIN_NO(16) | 1)
-#define MT8135_PIN_16_NWEB__FUNC_EINT145 (MTK_PIN_NO(16) | 2)
-#define MT8135_PIN_16_NWEB__FUNC_A_FUNC_DIN_0 (MTK_PIN_NO(16) | 3)
-#define MT8135_PIN_16_NWEB__FUNC_CM2PCLK_1X (MTK_PIN_NO(16) | 4)
-#define MT8135_PIN_16_NWEB__FUNC_IRDA_PDN (MTK_PIN_NO(16) | 5)
-#define MT8135_PIN_16_NWEB__FUNC_TESTA_OUT10 (MTK_PIN_NO(16) | 7)
-
-#define MT8135_PIN_17_NLD0__FUNC_GPIO17 (MTK_PIN_NO(17) | 0)
-#define MT8135_PIN_17_NLD0__FUNC_NLD0 (MTK_PIN_NO(17) | 1)
-#define MT8135_PIN_17_NLD0__FUNC_EINT146 (MTK_PIN_NO(17) | 2)
-#define MT8135_PIN_17_NLD0__FUNC_A_FUNC_DIN_1 (MTK_PIN_NO(17) | 3)
-#define MT8135_PIN_17_NLD0__FUNC_CM2DAT_1X_0 (MTK_PIN_NO(17) | 4)
-#define MT8135_PIN_17_NLD0__FUNC_I2SIN_CK (MTK_PIN_NO(17) | 5)
-#define MT8135_PIN_17_NLD0__FUNC_DAC_CK (MTK_PIN_NO(17) | 6)
-#define MT8135_PIN_17_NLD0__FUNC_TESTA_OUT11 (MTK_PIN_NO(17) | 7)
-
-#define MT8135_PIN_18_NLD1__FUNC_GPIO18 (MTK_PIN_NO(18) | 0)
-#define MT8135_PIN_18_NLD1__FUNC_NLD1 (MTK_PIN_NO(18) | 1)
-#define MT8135_PIN_18_NLD1__FUNC_EINT147 (MTK_PIN_NO(18) | 2)
-#define MT8135_PIN_18_NLD1__FUNC_A_FUNC_DIN_2 (MTK_PIN_NO(18) | 3)
-#define MT8135_PIN_18_NLD1__FUNC_CM2DAT_1X_1 (MTK_PIN_NO(18) | 4)
-#define MT8135_PIN_18_NLD1__FUNC_I2SIN_WS (MTK_PIN_NO(18) | 5)
-#define MT8135_PIN_18_NLD1__FUNC_DAC_WS (MTK_PIN_NO(18) | 6)
-#define MT8135_PIN_18_NLD1__FUNC_TESTA_OUT12 (MTK_PIN_NO(18) | 7)
-
-#define MT8135_PIN_19_NLD2__FUNC_GPIO19 (MTK_PIN_NO(19) | 0)
-#define MT8135_PIN_19_NLD2__FUNC_NLD2 (MTK_PIN_NO(19) | 1)
-#define MT8135_PIN_19_NLD2__FUNC_EINT148 (MTK_PIN_NO(19) | 2)
-#define MT8135_PIN_19_NLD2__FUNC_A_FUNC_DIN_3 (MTK_PIN_NO(19) | 3)
-#define MT8135_PIN_19_NLD2__FUNC_CM2DAT_1X_2 (MTK_PIN_NO(19) | 4)
-#define MT8135_PIN_19_NLD2__FUNC_I2SOUT_DAT (MTK_PIN_NO(19) | 5)
-#define MT8135_PIN_19_NLD2__FUNC_DAC_DAT_OUT (MTK_PIN_NO(19) | 6)
-#define MT8135_PIN_19_NLD2__FUNC_TESTA_OUT13 (MTK_PIN_NO(19) | 7)
-
-#define MT8135_PIN_20_NLD3__FUNC_GPIO20 (MTK_PIN_NO(20) | 0)
-#define MT8135_PIN_20_NLD3__FUNC_NLD3 (MTK_PIN_NO(20) | 1)
-#define MT8135_PIN_20_NLD3__FUNC_EINT149 (MTK_PIN_NO(20) | 2)
-#define MT8135_PIN_20_NLD3__FUNC_A_FUNC_DIN_4 (MTK_PIN_NO(20) | 3)
-#define MT8135_PIN_20_NLD3__FUNC_CM2DAT_1X_3 (MTK_PIN_NO(20) | 4)
-#define MT8135_PIN_20_NLD3__FUNC_TESTA_OUT14 (MTK_PIN_NO(20) | 7)
-
-#define MT8135_PIN_21_NLD4__FUNC_GPIO21 (MTK_PIN_NO(21) | 0)
-#define MT8135_PIN_21_NLD4__FUNC_NLD4 (MTK_PIN_NO(21) | 1)
-#define MT8135_PIN_21_NLD4__FUNC_EINT150 (MTK_PIN_NO(21) | 2)
-#define MT8135_PIN_21_NLD4__FUNC_A_FUNC_DIN_5 (MTK_PIN_NO(21) | 3)
-#define MT8135_PIN_21_NLD4__FUNC_CM2DAT_1X_4 (MTK_PIN_NO(21) | 4)
-#define MT8135_PIN_21_NLD4__FUNC_TESTA_OUT15 (MTK_PIN_NO(21) | 7)
-
-#define MT8135_PIN_22_NLD5__FUNC_GPIO22 (MTK_PIN_NO(22) | 0)
-#define MT8135_PIN_22_NLD5__FUNC_NLD5 (MTK_PIN_NO(22) | 1)
-#define MT8135_PIN_22_NLD5__FUNC_EINT151 (MTK_PIN_NO(22) | 2)
-#define MT8135_PIN_22_NLD5__FUNC_A_FUNC_DIN_6 (MTK_PIN_NO(22) | 3)
-#define MT8135_PIN_22_NLD5__FUNC_CM2DAT_1X_5 (MTK_PIN_NO(22) | 4)
-#define MT8135_PIN_22_NLD5__FUNC_TESTA_OUT16 (MTK_PIN_NO(22) | 7)
-
-#define MT8135_PIN_23_NLD6__FUNC_GPIO23 (MTK_PIN_NO(23) | 0)
-#define MT8135_PIN_23_NLD6__FUNC_NLD6 (MTK_PIN_NO(23) | 1)
-#define MT8135_PIN_23_NLD6__FUNC_EINT152 (MTK_PIN_NO(23) | 2)
-#define MT8135_PIN_23_NLD6__FUNC_A_FUNC_DIN_7 (MTK_PIN_NO(23) | 3)
-#define MT8135_PIN_23_NLD6__FUNC_CM2DAT_1X_6 (MTK_PIN_NO(23) | 4)
-#define MT8135_PIN_23_NLD6__FUNC_TESTA_OUT17 (MTK_PIN_NO(23) | 7)
-
-#define MT8135_PIN_24_NLD7__FUNC_GPIO24 (MTK_PIN_NO(24) | 0)
-#define MT8135_PIN_24_NLD7__FUNC_NLD7 (MTK_PIN_NO(24) | 1)
-#define MT8135_PIN_24_NLD7__FUNC_EINT153 (MTK_PIN_NO(24) | 2)
-#define MT8135_PIN_24_NLD7__FUNC_A_FUNC_DIN_8 (MTK_PIN_NO(24) | 3)
-#define MT8135_PIN_24_NLD7__FUNC_CM2DAT_1X_7 (MTK_PIN_NO(24) | 4)
-#define MT8135_PIN_24_NLD7__FUNC_TESTA_OUT18 (MTK_PIN_NO(24) | 7)
-
-#define MT8135_PIN_25_NLD8__FUNC_GPIO25 (MTK_PIN_NO(25) | 0)
-#define MT8135_PIN_25_NLD8__FUNC_NLD8 (MTK_PIN_NO(25) | 1)
-#define MT8135_PIN_25_NLD8__FUNC_EINT154 (MTK_PIN_NO(25) | 2)
-#define MT8135_PIN_25_NLD8__FUNC_CM2DAT_1X_8 (MTK_PIN_NO(25) | 4)
-
-#define MT8135_PIN_26_NLD9__FUNC_GPIO26 (MTK_PIN_NO(26) | 0)
-#define MT8135_PIN_26_NLD9__FUNC_NLD9 (MTK_PIN_NO(26) | 1)
-#define MT8135_PIN_26_NLD9__FUNC_EINT155 (MTK_PIN_NO(26) | 2)
-#define MT8135_PIN_26_NLD9__FUNC_CM2DAT_1X_9 (MTK_PIN_NO(26) | 4)
-#define MT8135_PIN_26_NLD9__FUNC_PWM1 (MTK_PIN_NO(26) | 5)
-
-#define MT8135_PIN_27_NLD10__FUNC_GPIO27 (MTK_PIN_NO(27) | 0)
-#define MT8135_PIN_27_NLD10__FUNC_NLD10 (MTK_PIN_NO(27) | 1)
-#define MT8135_PIN_27_NLD10__FUNC_EINT156 (MTK_PIN_NO(27) | 2)
-#define MT8135_PIN_27_NLD10__FUNC_CM2VSYNC_1X (MTK_PIN_NO(27) | 4)
-#define MT8135_PIN_27_NLD10__FUNC_PWM2 (MTK_PIN_NO(27) | 5)
-
-#define MT8135_PIN_28_NLD11__FUNC_GPIO28 (MTK_PIN_NO(28) | 0)
-#define MT8135_PIN_28_NLD11__FUNC_NLD11 (MTK_PIN_NO(28) | 1)
-#define MT8135_PIN_28_NLD11__FUNC_EINT157 (MTK_PIN_NO(28) | 2)
-#define MT8135_PIN_28_NLD11__FUNC_CM2HSYNC_1X (MTK_PIN_NO(28) | 4)
-#define MT8135_PIN_28_NLD11__FUNC_PWM3 (MTK_PIN_NO(28) | 5)
-
-#define MT8135_PIN_29_NLD12__FUNC_GPIO29 (MTK_PIN_NO(29) | 0)
-#define MT8135_PIN_29_NLD12__FUNC_NLD12 (MTK_PIN_NO(29) | 1)
-#define MT8135_PIN_29_NLD12__FUNC_EINT158 (MTK_PIN_NO(29) | 2)
-#define MT8135_PIN_29_NLD12__FUNC_I2SIN_CK (MTK_PIN_NO(29) | 3)
-#define MT8135_PIN_29_NLD12__FUNC_DAC_CK (MTK_PIN_NO(29) | 4)
-#define MT8135_PIN_29_NLD12__FUNC_PCM1_CK (MTK_PIN_NO(29) | 5)
-
-#define MT8135_PIN_30_NLD13__FUNC_GPIO30 (MTK_PIN_NO(30) | 0)
-#define MT8135_PIN_30_NLD13__FUNC_NLD13 (MTK_PIN_NO(30) | 1)
-#define MT8135_PIN_30_NLD13__FUNC_EINT159 (MTK_PIN_NO(30) | 2)
-#define MT8135_PIN_30_NLD13__FUNC_I2SIN_WS (MTK_PIN_NO(30) | 3)
-#define MT8135_PIN_30_NLD13__FUNC_DAC_WS (MTK_PIN_NO(30) | 4)
-#define MT8135_PIN_30_NLD13__FUNC_PCM1_WS (MTK_PIN_NO(30) | 5)
-
-#define MT8135_PIN_31_NLD14__FUNC_GPIO31 (MTK_PIN_NO(31) | 0)
-#define MT8135_PIN_31_NLD14__FUNC_NLD14 (MTK_PIN_NO(31) | 1)
-#define MT8135_PIN_31_NLD14__FUNC_EINT160 (MTK_PIN_NO(31) | 2)
-#define MT8135_PIN_31_NLD14__FUNC_I2SOUT_DAT (MTK_PIN_NO(31) | 3)
-#define MT8135_PIN_31_NLD14__FUNC_DAC_DAT_OUT (MTK_PIN_NO(31) | 4)
-#define MT8135_PIN_31_NLD14__FUNC_PCM1_DO (MTK_PIN_NO(31) | 5)
-
-#define MT8135_PIN_32_NLD15__FUNC_GPIO32 (MTK_PIN_NO(32) | 0)
-#define MT8135_PIN_32_NLD15__FUNC_NLD15 (MTK_PIN_NO(32) | 1)
-#define MT8135_PIN_32_NLD15__FUNC_EINT161 (MTK_PIN_NO(32) | 2)
-#define MT8135_PIN_32_NLD15__FUNC_DISP_PWM (MTK_PIN_NO(32) | 3)
-#define MT8135_PIN_32_NLD15__FUNC_PWM4 (MTK_PIN_NO(32) | 4)
-#define MT8135_PIN_32_NLD15__FUNC_PCM1_DI (MTK_PIN_NO(32) | 5)
-
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_GPIO33 (MTK_PIN_NO(33) | 0)
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_MSDC0_RSTB (MTK_PIN_NO(33) | 1)
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_EINT50 (MTK_PIN_NO(33) | 2)
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_I2SIN_DAT (MTK_PIN_NO(33) | 3)
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_PCM1_DI (MTK_PIN_NO(33) | 5)
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_SPI1_MI (MTK_PIN_NO(33) | 6)
-#define MT8135_PIN_33_MSDC0_RSTB__FUNC_NLD10 (MTK_PIN_NO(33) | 7)
-
-#define MT8135_PIN_34_IDDIG__FUNC_GPIO34 (MTK_PIN_NO(34) | 0)
-#define MT8135_PIN_34_IDDIG__FUNC_IDDIG (MTK_PIN_NO(34) | 1)
-#define MT8135_PIN_34_IDDIG__FUNC_EINT34 (MTK_PIN_NO(34) | 2)
-
-#define MT8135_PIN_35_SCL3__FUNC_GPIO35 (MTK_PIN_NO(35) | 0)
-#define MT8135_PIN_35_SCL3__FUNC_SCL3 (MTK_PIN_NO(35) | 1)
-#define MT8135_PIN_35_SCL3__FUNC_EINT96 (MTK_PIN_NO(35) | 2)
-#define MT8135_PIN_35_SCL3__FUNC_CLKM6 (MTK_PIN_NO(35) | 3)
-#define MT8135_PIN_35_SCL3__FUNC_PWM6 (MTK_PIN_NO(35) | 4)
-
-#define MT8135_PIN_36_SDA3__FUNC_GPIO36 (MTK_PIN_NO(36) | 0)
-#define MT8135_PIN_36_SDA3__FUNC_SDA3 (MTK_PIN_NO(36) | 1)
-#define MT8135_PIN_36_SDA3__FUNC_EINT97 (MTK_PIN_NO(36) | 2)
-
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_GPIO37 (MTK_PIN_NO(37) | 0)
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_AUD_CLK (MTK_PIN_NO(37) | 1)
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_ADC_CK (MTK_PIN_NO(37) | 2)
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_HDMI_SDATA0 (MTK_PIN_NO(37) | 3)
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_EINT19 (MTK_PIN_NO(37) | 4)
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_USB_TEST_IO_6 (MTK_PIN_NO(37) | 5)
-#define MT8135_PIN_37_AUD_CLK_MOSI__FUNC_TESTA_OUT19 (MTK_PIN_NO(37) | 7)
-
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_GPIO38 (MTK_PIN_NO(38) | 0)
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_AUD_DAT_MOSI (MTK_PIN_NO(38) | 1)
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_ADC_WS (MTK_PIN_NO(38) | 2)
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_AUD_DAT_MISO (MTK_PIN_NO(38) | 3)
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_EINT21 (MTK_PIN_NO(38) | 4)
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_USB_TEST_IO_7 (MTK_PIN_NO(38) | 5)
-#define MT8135_PIN_38_AUD_DAT_MOSI__FUNC_TESTA_OUT20 (MTK_PIN_NO(38) | 7)
-
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_GPIO39 (MTK_PIN_NO(39) | 0)
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_AUD_DAT_MISO (MTK_PIN_NO(39) | 1)
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_ADC_DAT_IN (MTK_PIN_NO(39) | 2)
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_AUD_DAT_MOSI (MTK_PIN_NO(39) | 3)
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_EINT20 (MTK_PIN_NO(39) | 4)
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_USB_TEST_IO_8 (MTK_PIN_NO(39) | 5)
-#define MT8135_PIN_39_AUD_DAT_MISO__FUNC_TESTA_OUT21 (MTK_PIN_NO(39) | 7)
-
-#define MT8135_PIN_40_DAC_CLK__FUNC_GPIO40 (MTK_PIN_NO(40) | 0)
-#define MT8135_PIN_40_DAC_CLK__FUNC_DAC_CK (MTK_PIN_NO(40) | 1)
-#define MT8135_PIN_40_DAC_CLK__FUNC_EINT22 (MTK_PIN_NO(40) | 2)
-#define MT8135_PIN_40_DAC_CLK__FUNC_HDMI_SDATA1 (MTK_PIN_NO(40) | 3)
-#define MT8135_PIN_40_DAC_CLK__FUNC_USB_TEST_IO_9 (MTK_PIN_NO(40) | 5)
-#define MT8135_PIN_40_DAC_CLK__FUNC_TESTA_OUT22 (MTK_PIN_NO(40) | 7)
-
-#define MT8135_PIN_41_DAC_WS__FUNC_GPIO41 (MTK_PIN_NO(41) | 0)
-#define MT8135_PIN_41_DAC_WS__FUNC_DAC_WS (MTK_PIN_NO(41) | 1)
-#define MT8135_PIN_41_DAC_WS__FUNC_EINT24 (MTK_PIN_NO(41) | 2)
-#define MT8135_PIN_41_DAC_WS__FUNC_HDMI_SDATA2 (MTK_PIN_NO(41) | 3)
-#define MT8135_PIN_41_DAC_WS__FUNC_USB_TEST_IO_10 (MTK_PIN_NO(41) | 5)
-#define MT8135_PIN_41_DAC_WS__FUNC_TESTA_OUT23 (MTK_PIN_NO(41) | 7)
-
-#define MT8135_PIN_42_DAC_DAT_OUT__FUNC_GPIO42 (MTK_PIN_NO(42) | 0)
-#define MT8135_PIN_42_DAC_DAT_OUT__FUNC_DAC_DAT_OUT (MTK_PIN_NO(42) | 1)
-#define MT8135_PIN_42_DAC_DAT_OUT__FUNC_EINT23 (MTK_PIN_NO(42) | 2)
-#define MT8135_PIN_42_DAC_DAT_OUT__FUNC_HDMI_SDATA3 (MTK_PIN_NO(42) | 3)
-#define MT8135_PIN_42_DAC_DAT_OUT__FUNC_USB_TEST_IO_11 (MTK_PIN_NO(42) | 5)
-#define MT8135_PIN_42_DAC_DAT_OUT__FUNC_TESTA_OUT24 (MTK_PIN_NO(42) | 7)
-
-#define MT8135_PIN_43_PWRAP_SPI0_MO__FUNC_GPIO43 (MTK_PIN_NO(43) | 0)
-#define MT8135_PIN_43_PWRAP_SPI0_MO__FUNC_PWRAP_SPIDI (MTK_PIN_NO(43) | 1)
-#define MT8135_PIN_43_PWRAP_SPI0_MO__FUNC_EINT29 (MTK_PIN_NO(43) | 2)
-
-#define MT8135_PIN_44_PWRAP_SPI0_MI__FUNC_GPIO44 (MTK_PIN_NO(44) | 0)
-#define MT8135_PIN_44_PWRAP_SPI0_MI__FUNC_PWRAP_SPIDO (MTK_PIN_NO(44) | 1)
-#define MT8135_PIN_44_PWRAP_SPI0_MI__FUNC_EINT28 (MTK_PIN_NO(44) | 2)
-
-#define MT8135_PIN_45_PWRAP_SPI0_CSN__FUNC_GPIO45 (MTK_PIN_NO(45) | 0)
-#define MT8135_PIN_45_PWRAP_SPI0_CSN__FUNC_PWRAP_SPICS_B_I (MTK_PIN_NO(45) | 1)
-#define MT8135_PIN_45_PWRAP_SPI0_CSN__FUNC_EINT27 (MTK_PIN_NO(45) | 2)
-
-#define MT8135_PIN_46_PWRAP_SPI0_CLK__FUNC_GPIO46 (MTK_PIN_NO(46) | 0)
-#define MT8135_PIN_46_PWRAP_SPI0_CLK__FUNC_PWRAP_SPICK_I (MTK_PIN_NO(46) | 1)
-#define MT8135_PIN_46_PWRAP_SPI0_CLK__FUNC_EINT26 (MTK_PIN_NO(46) | 2)
-
-#define MT8135_PIN_47_PWRAP_EVENT__FUNC_GPIO47 (MTK_PIN_NO(47) | 0)
-#define MT8135_PIN_47_PWRAP_EVENT__FUNC_PWRAP_EVENT_IN (MTK_PIN_NO(47) | 1)
-#define MT8135_PIN_47_PWRAP_EVENT__FUNC_EINT25 (MTK_PIN_NO(47) | 2)
-#define MT8135_PIN_47_PWRAP_EVENT__FUNC_TESTA_OUT2 (MTK_PIN_NO(47) | 7)
-
-#define MT8135_PIN_48_RTC32K_CK__FUNC_GPIO48 (MTK_PIN_NO(48) | 0)
-#define MT8135_PIN_48_RTC32K_CK__FUNC_RTC32K_CK (MTK_PIN_NO(48) | 1)
-
-#define MT8135_PIN_49_WATCHDOG__FUNC_GPIO49 (MTK_PIN_NO(49) | 0)
-#define MT8135_PIN_49_WATCHDOG__FUNC_WATCHDOG (MTK_PIN_NO(49) | 1)
-#define MT8135_PIN_49_WATCHDOG__FUNC_EINT36 (MTK_PIN_NO(49) | 2)
-
-#define MT8135_PIN_50_SRCLKENA__FUNC_GPIO50 (MTK_PIN_NO(50) | 0)
-#define MT8135_PIN_50_SRCLKENA__FUNC_SRCLKENA (MTK_PIN_NO(50) | 1)
-#define MT8135_PIN_50_SRCLKENA__FUNC_EINT38 (MTK_PIN_NO(50) | 2)
-
-#define MT8135_PIN_51_SRCVOLTEN__FUNC_GPIO51 (MTK_PIN_NO(51) | 0)
-#define MT8135_PIN_51_SRCVOLTEN__FUNC_SRCVOLTEN (MTK_PIN_NO(51) | 1)
-#define MT8135_PIN_51_SRCVOLTEN__FUNC_EINT37 (MTK_PIN_NO(51) | 2)
-
-#define MT8135_PIN_52_EINT0__FUNC_GPIO52 (MTK_PIN_NO(52) | 0)
-#define MT8135_PIN_52_EINT0__FUNC_EINT0 (MTK_PIN_NO(52) | 1)
-#define MT8135_PIN_52_EINT0__FUNC_PWM1 (MTK_PIN_NO(52) | 2)
-#define MT8135_PIN_52_EINT0__FUNC_CLKM0 (MTK_PIN_NO(52) | 3)
-#define MT8135_PIN_52_EINT0__FUNC_SPDIF_OUT (MTK_PIN_NO(52) | 4)
-#define MT8135_PIN_52_EINT0__FUNC_USB_TEST_IO_12 (MTK_PIN_NO(52) | 5)
-#define MT8135_PIN_52_EINT0__FUNC_USB_SCL (MTK_PIN_NO(52) | 7)
-
-#define MT8135_PIN_53_URXD2__FUNC_GPIO53 (MTK_PIN_NO(53) | 0)
-#define MT8135_PIN_53_URXD2__FUNC_URXD2 (MTK_PIN_NO(53) | 1)
-#define MT8135_PIN_53_URXD2__FUNC_EINT83 (MTK_PIN_NO(53) | 2)
-#define MT8135_PIN_53_URXD2__FUNC_HDMI_LRCK (MTK_PIN_NO(53) | 4)
-#define MT8135_PIN_53_URXD2__FUNC_CLKM3 (MTK_PIN_NO(53) | 5)
-#define MT8135_PIN_53_URXD2__FUNC_UTXD2 (MTK_PIN_NO(53) | 7)
-
-#define MT8135_PIN_54_UTXD2__FUNC_GPIO54 (MTK_PIN_NO(54) | 0)
-#define MT8135_PIN_54_UTXD2__FUNC_UTXD2 (MTK_PIN_NO(54) | 1)
-#define MT8135_PIN_54_UTXD2__FUNC_EINT82 (MTK_PIN_NO(54) | 2)
-#define MT8135_PIN_54_UTXD2__FUNC_HDMI_BCK_OUT (MTK_PIN_NO(54) | 4)
-#define MT8135_PIN_54_UTXD2__FUNC_CLKM2 (MTK_PIN_NO(54) | 5)
-#define MT8135_PIN_54_UTXD2__FUNC_URXD2 (MTK_PIN_NO(54) | 7)
-
-#define MT8135_PIN_55_UCTS2__FUNC_GPIO55 (MTK_PIN_NO(55) | 0)
-#define MT8135_PIN_55_UCTS2__FUNC_UCTS2 (MTK_PIN_NO(55) | 1)
-#define MT8135_PIN_55_UCTS2__FUNC_EINT84 (MTK_PIN_NO(55) | 2)
-#define MT8135_PIN_55_UCTS2__FUNC_PWM1 (MTK_PIN_NO(55) | 5)
-#define MT8135_PIN_55_UCTS2__FUNC_URTS2 (MTK_PIN_NO(55) | 7)
-
-#define MT8135_PIN_56_URTS2__FUNC_GPIO56 (MTK_PIN_NO(56) | 0)
-#define MT8135_PIN_56_URTS2__FUNC_URTS2 (MTK_PIN_NO(56) | 1)
-#define MT8135_PIN_56_URTS2__FUNC_EINT85 (MTK_PIN_NO(56) | 2)
-#define MT8135_PIN_56_URTS2__FUNC_PWM2 (MTK_PIN_NO(56) | 5)
-#define MT8135_PIN_56_URTS2__FUNC_UCTS2 (MTK_PIN_NO(56) | 7)
-
-#define MT8135_PIN_57_JTCK__FUNC_GPIO57 (MTK_PIN_NO(57) | 0)
-#define MT8135_PIN_57_JTCK__FUNC_JTCK (MTK_PIN_NO(57) | 1)
-#define MT8135_PIN_57_JTCK__FUNC_EINT188 (MTK_PIN_NO(57) | 2)
-#define MT8135_PIN_57_JTCK__FUNC_DSP1_ICK (MTK_PIN_NO(57) | 3)
-
-#define MT8135_PIN_58_JTDO__FUNC_GPIO58 (MTK_PIN_NO(58) | 0)
-#define MT8135_PIN_58_JTDO__FUNC_JTDO (MTK_PIN_NO(58) | 1)
-#define MT8135_PIN_58_JTDO__FUNC_EINT190 (MTK_PIN_NO(58) | 2)
-#define MT8135_PIN_58_JTDO__FUNC_DSP2_IMS (MTK_PIN_NO(58) | 3)
-
-#define MT8135_PIN_59_JTRST_B__FUNC_GPIO59 (MTK_PIN_NO(59) | 0)
-#define MT8135_PIN_59_JTRST_B__FUNC_JTRST_B (MTK_PIN_NO(59) | 1)
-#define MT8135_PIN_59_JTRST_B__FUNC_EINT0 (MTK_PIN_NO(59) | 2)
-#define MT8135_PIN_59_JTRST_B__FUNC_DSP2_ICK (MTK_PIN_NO(59) | 3)
-
-#define MT8135_PIN_60_JTDI__FUNC_GPIO60 (MTK_PIN_NO(60) | 0)
-#define MT8135_PIN_60_JTDI__FUNC_JTDI (MTK_PIN_NO(60) | 1)
-#define MT8135_PIN_60_JTDI__FUNC_EINT189 (MTK_PIN_NO(60) | 2)
-#define MT8135_PIN_60_JTDI__FUNC_DSP1_IMS (MTK_PIN_NO(60) | 3)
-
-#define MT8135_PIN_61_JRTCK__FUNC_GPIO61 (MTK_PIN_NO(61) | 0)
-#define MT8135_PIN_61_JRTCK__FUNC_JRTCK (MTK_PIN_NO(61) | 1)
-#define MT8135_PIN_61_JRTCK__FUNC_EINT187 (MTK_PIN_NO(61) | 2)
-#define MT8135_PIN_61_JRTCK__FUNC_DSP1_ID (MTK_PIN_NO(61) | 3)
-
-#define MT8135_PIN_62_JTMS__FUNC_GPIO62 (MTK_PIN_NO(62) | 0)
-#define MT8135_PIN_62_JTMS__FUNC_JTMS (MTK_PIN_NO(62) | 1)
-#define MT8135_PIN_62_JTMS__FUNC_EINT191 (MTK_PIN_NO(62) | 2)
-#define MT8135_PIN_62_JTMS__FUNC_DSP2_ID (MTK_PIN_NO(62) | 3)
-
-#define MT8135_PIN_63_MSDC1_INSI__FUNC_GPIO63 (MTK_PIN_NO(63) | 0)
-#define MT8135_PIN_63_MSDC1_INSI__FUNC_MSDC1_INSI (MTK_PIN_NO(63) | 1)
-#define MT8135_PIN_63_MSDC1_INSI__FUNC_SCL5 (MTK_PIN_NO(63) | 3)
-#define MT8135_PIN_63_MSDC1_INSI__FUNC_PWM6 (MTK_PIN_NO(63) | 4)
-#define MT8135_PIN_63_MSDC1_INSI__FUNC_CLKM5 (MTK_PIN_NO(63) | 5)
-#define MT8135_PIN_63_MSDC1_INSI__FUNC_TESTB_OUT6 (MTK_PIN_NO(63) | 7)
-
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_GPIO64 (MTK_PIN_NO(64) | 0)
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_MSDC1_SDWPI (MTK_PIN_NO(64) | 1)
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_EINT58 (MTK_PIN_NO(64) | 2)
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_SDA5 (MTK_PIN_NO(64) | 3)
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_PWM7 (MTK_PIN_NO(64) | 4)
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_CLKM6 (MTK_PIN_NO(64) | 5)
-#define MT8135_PIN_64_MSDC1_SDWPI__FUNC_TESTB_OUT7 (MTK_PIN_NO(64) | 7)
-
-#define MT8135_PIN_65_MSDC2_INSI__FUNC_GPIO65 (MTK_PIN_NO(65) | 0)
-#define MT8135_PIN_65_MSDC2_INSI__FUNC_MSDC2_INSI (MTK_PIN_NO(65) | 1)
-#define MT8135_PIN_65_MSDC2_INSI__FUNC_USB_TEST_IO_27 (MTK_PIN_NO(65) | 5)
-#define MT8135_PIN_65_MSDC2_INSI__FUNC_TESTA_OUT3 (MTK_PIN_NO(65) | 7)
-
-#define MT8135_PIN_66_MSDC2_SDWPI__FUNC_GPIO66 (MTK_PIN_NO(66) | 0)
-#define MT8135_PIN_66_MSDC2_SDWPI__FUNC_MSDC2_SDWPI (MTK_PIN_NO(66) | 1)
-#define MT8135_PIN_66_MSDC2_SDWPI__FUNC_EINT66 (MTK_PIN_NO(66) | 2)
-#define MT8135_PIN_66_MSDC2_SDWPI__FUNC_USB_TEST_IO_28 (MTK_PIN_NO(66) | 5)
-
-#define MT8135_PIN_67_URXD4__FUNC_GPIO67 (MTK_PIN_NO(67) | 0)
-#define MT8135_PIN_67_URXD4__FUNC_URXD4 (MTK_PIN_NO(67) | 1)
-#define MT8135_PIN_67_URXD4__FUNC_EINT89 (MTK_PIN_NO(67) | 2)
-#define MT8135_PIN_67_URXD4__FUNC_URXD1 (MTK_PIN_NO(67) | 3)
-#define MT8135_PIN_67_URXD4__FUNC_UTXD4 (MTK_PIN_NO(67) | 6)
-#define MT8135_PIN_67_URXD4__FUNC_TESTB_OUT10 (MTK_PIN_NO(67) | 7)
-
-#define MT8135_PIN_68_UTXD4__FUNC_GPIO68 (MTK_PIN_NO(68) | 0)
-#define MT8135_PIN_68_UTXD4__FUNC_UTXD4 (MTK_PIN_NO(68) | 1)
-#define MT8135_PIN_68_UTXD4__FUNC_EINT88 (MTK_PIN_NO(68) | 2)
-#define MT8135_PIN_68_UTXD4__FUNC_UTXD1 (MTK_PIN_NO(68) | 3)
-#define MT8135_PIN_68_UTXD4__FUNC_URXD4 (MTK_PIN_NO(68) | 6)
-#define MT8135_PIN_68_UTXD4__FUNC_TESTB_OUT11 (MTK_PIN_NO(68) | 7)
-
-#define MT8135_PIN_69_URXD1__FUNC_GPIO69 (MTK_PIN_NO(69) | 0)
-#define MT8135_PIN_69_URXD1__FUNC_URXD1 (MTK_PIN_NO(69) | 1)
-#define MT8135_PIN_69_URXD1__FUNC_EINT79 (MTK_PIN_NO(69) | 2)
-#define MT8135_PIN_69_URXD1__FUNC_URXD4 (MTK_PIN_NO(69) | 3)
-#define MT8135_PIN_69_URXD1__FUNC_UTXD1 (MTK_PIN_NO(69) | 6)
-#define MT8135_PIN_69_URXD1__FUNC_TESTB_OUT24 (MTK_PIN_NO(69) | 7)
-
-#define MT8135_PIN_70_UTXD1__FUNC_GPIO70 (MTK_PIN_NO(70) | 0)
-#define MT8135_PIN_70_UTXD1__FUNC_UTXD1 (MTK_PIN_NO(70) | 1)
-#define MT8135_PIN_70_UTXD1__FUNC_EINT78 (MTK_PIN_NO(70) | 2)
-#define MT8135_PIN_70_UTXD1__FUNC_UTXD4 (MTK_PIN_NO(70) | 3)
-#define MT8135_PIN_70_UTXD1__FUNC_URXD1 (MTK_PIN_NO(70) | 6)
-#define MT8135_PIN_70_UTXD1__FUNC_TESTB_OUT25 (MTK_PIN_NO(70) | 7)
-
-#define MT8135_PIN_71_UCTS1__FUNC_GPIO71 (MTK_PIN_NO(71) | 0)
-#define MT8135_PIN_71_UCTS1__FUNC_UCTS1 (MTK_PIN_NO(71) | 1)
-#define MT8135_PIN_71_UCTS1__FUNC_EINT80 (MTK_PIN_NO(71) | 2)
-#define MT8135_PIN_71_UCTS1__FUNC_CLKM0 (MTK_PIN_NO(71) | 5)
-#define MT8135_PIN_71_UCTS1__FUNC_URTS1 (MTK_PIN_NO(71) | 6)
-#define MT8135_PIN_71_UCTS1__FUNC_TESTB_OUT31 (MTK_PIN_NO(71) | 7)
-
-#define MT8135_PIN_72_URTS1__FUNC_GPIO72 (MTK_PIN_NO(72) | 0)
-#define MT8135_PIN_72_URTS1__FUNC_URTS1 (MTK_PIN_NO(72) | 1)
-#define MT8135_PIN_72_URTS1__FUNC_EINT81 (MTK_PIN_NO(72) | 2)
-#define MT8135_PIN_72_URTS1__FUNC_CLKM1 (MTK_PIN_NO(72) | 5)
-#define MT8135_PIN_72_URTS1__FUNC_UCTS1 (MTK_PIN_NO(72) | 6)
-#define MT8135_PIN_72_URTS1__FUNC_TESTB_OUT21 (MTK_PIN_NO(72) | 7)
-
-#define MT8135_PIN_73_PWM1__FUNC_GPIO73 (MTK_PIN_NO(73) | 0)
-#define MT8135_PIN_73_PWM1__FUNC_PWM1 (MTK_PIN_NO(73) | 1)
-#define MT8135_PIN_73_PWM1__FUNC_EINT73 (MTK_PIN_NO(73) | 2)
-#define MT8135_PIN_73_PWM1__FUNC_USB_DRVVBUS (MTK_PIN_NO(73) | 5)
-#define MT8135_PIN_73_PWM1__FUNC_DISP_PWM (MTK_PIN_NO(73) | 6)
-#define MT8135_PIN_73_PWM1__FUNC_TESTB_OUT8 (MTK_PIN_NO(73) | 7)
-
-#define MT8135_PIN_74_PWM2__FUNC_GPIO74 (MTK_PIN_NO(74) | 0)
-#define MT8135_PIN_74_PWM2__FUNC_PWM2 (MTK_PIN_NO(74) | 1)
-#define MT8135_PIN_74_PWM2__FUNC_EINT74 (MTK_PIN_NO(74) | 2)
-#define MT8135_PIN_74_PWM2__FUNC_DPI33_CK (MTK_PIN_NO(74) | 3)
-#define MT8135_PIN_74_PWM2__FUNC_PWM5 (MTK_PIN_NO(74) | 4)
-#define MT8135_PIN_74_PWM2__FUNC_URXD2 (MTK_PIN_NO(74) | 5)
-#define MT8135_PIN_74_PWM2__FUNC_DISP_PWM (MTK_PIN_NO(74) | 6)
-#define MT8135_PIN_74_PWM2__FUNC_TESTB_OUT9 (MTK_PIN_NO(74) | 7)
-
-#define MT8135_PIN_75_PWM3__FUNC_GPIO75 (MTK_PIN_NO(75) | 0)
-#define MT8135_PIN_75_PWM3__FUNC_PWM3 (MTK_PIN_NO(75) | 1)
-#define MT8135_PIN_75_PWM3__FUNC_EINT75 (MTK_PIN_NO(75) | 2)
-#define MT8135_PIN_75_PWM3__FUNC_DPI33_D0 (MTK_PIN_NO(75) | 3)
-#define MT8135_PIN_75_PWM3__FUNC_PWM6 (MTK_PIN_NO(75) | 4)
-#define MT8135_PIN_75_PWM3__FUNC_UTXD2 (MTK_PIN_NO(75) | 5)
-#define MT8135_PIN_75_PWM3__FUNC_DISP_PWM (MTK_PIN_NO(75) | 6)
-#define MT8135_PIN_75_PWM3__FUNC_TESTB_OUT12 (MTK_PIN_NO(75) | 7)
-
-#define MT8135_PIN_76_PWM4__FUNC_GPIO76 (MTK_PIN_NO(76) | 0)
-#define MT8135_PIN_76_PWM4__FUNC_PWM4 (MTK_PIN_NO(76) | 1)
-#define MT8135_PIN_76_PWM4__FUNC_EINT76 (MTK_PIN_NO(76) | 2)
-#define MT8135_PIN_76_PWM4__FUNC_DPI33_D1 (MTK_PIN_NO(76) | 3)
-#define MT8135_PIN_76_PWM4__FUNC_PWM7 (MTK_PIN_NO(76) | 4)
-#define MT8135_PIN_76_PWM4__FUNC_DISP_PWM (MTK_PIN_NO(76) | 6)
-#define MT8135_PIN_76_PWM4__FUNC_TESTB_OUT13 (MTK_PIN_NO(76) | 7)
-
-#define MT8135_PIN_77_MSDC2_DAT2__FUNC_GPIO77 (MTK_PIN_NO(77) | 0)
-#define MT8135_PIN_77_MSDC2_DAT2__FUNC_MSDC2_DAT2 (MTK_PIN_NO(77) | 1)
-#define MT8135_PIN_77_MSDC2_DAT2__FUNC_EINT63 (MTK_PIN_NO(77) | 2)
-#define MT8135_PIN_77_MSDC2_DAT2__FUNC_DSP2_IMS (MTK_PIN_NO(77) | 4)
-#define MT8135_PIN_77_MSDC2_DAT2__FUNC_DPI33_D6 (MTK_PIN_NO(77) | 6)
-#define MT8135_PIN_77_MSDC2_DAT2__FUNC_TESTA_OUT25 (MTK_PIN_NO(77) | 7)
-
-#define MT8135_PIN_78_MSDC2_DAT3__FUNC_GPIO78 (MTK_PIN_NO(78) | 0)
-#define MT8135_PIN_78_MSDC2_DAT3__FUNC_MSDC2_DAT3 (MTK_PIN_NO(78) | 1)
-#define MT8135_PIN_78_MSDC2_DAT3__FUNC_EINT64 (MTK_PIN_NO(78) | 2)
-#define MT8135_PIN_78_MSDC2_DAT3__FUNC_DSP2_ID (MTK_PIN_NO(78) | 4)
-#define MT8135_PIN_78_MSDC2_DAT3__FUNC_DPI33_D7 (MTK_PIN_NO(78) | 6)
-#define MT8135_PIN_78_MSDC2_DAT3__FUNC_TESTA_OUT26 (MTK_PIN_NO(78) | 7)
-
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_GPIO79 (MTK_PIN_NO(79) | 0)
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_MSDC2_CMD (MTK_PIN_NO(79) | 1)
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_EINT60 (MTK_PIN_NO(79) | 2)
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_DSP1_IMS (MTK_PIN_NO(79) | 4)
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_PCM1_WS (MTK_PIN_NO(79) | 5)
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_DPI33_D3 (MTK_PIN_NO(79) | 6)
-#define MT8135_PIN_79_MSDC2_CMD__FUNC_TESTA_OUT0 (MTK_PIN_NO(79) | 7)
-
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_GPIO80 (MTK_PIN_NO(80) | 0)
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_MSDC2_CLK (MTK_PIN_NO(80) | 1)
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_EINT59 (MTK_PIN_NO(80) | 2)
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_DSP1_ICK (MTK_PIN_NO(80) | 4)
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_PCM1_CK (MTK_PIN_NO(80) | 5)
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_DPI33_D2 (MTK_PIN_NO(80) | 6)
-#define MT8135_PIN_80_MSDC2_CLK__FUNC_TESTA_OUT1 (MTK_PIN_NO(80) | 7)
-
-#define MT8135_PIN_81_MSDC2_DAT1__FUNC_GPIO81 (MTK_PIN_NO(81) | 0)
-#define MT8135_PIN_81_MSDC2_DAT1__FUNC_MSDC2_DAT1 (MTK_PIN_NO(81) | 1)
-#define MT8135_PIN_81_MSDC2_DAT1__FUNC_EINT62 (MTK_PIN_NO(81) | 2)
-#define MT8135_PIN_81_MSDC2_DAT1__FUNC_DSP2_ICK (MTK_PIN_NO(81) | 4)
-#define MT8135_PIN_81_MSDC2_DAT1__FUNC_PCM1_DO (MTK_PIN_NO(81) | 5)
-#define MT8135_PIN_81_MSDC2_DAT1__FUNC_DPI33_D5 (MTK_PIN_NO(81) | 6)
-
-#define MT8135_PIN_82_MSDC2_DAT0__FUNC_GPIO82 (MTK_PIN_NO(82) | 0)
-#define MT8135_PIN_82_MSDC2_DAT0__FUNC_MSDC2_DAT0 (MTK_PIN_NO(82) | 1)
-#define MT8135_PIN_82_MSDC2_DAT0__FUNC_EINT61 (MTK_PIN_NO(82) | 2)
-#define MT8135_PIN_82_MSDC2_DAT0__FUNC_DSP1_ID (MTK_PIN_NO(82) | 4)
-#define MT8135_PIN_82_MSDC2_DAT0__FUNC_PCM1_DI (MTK_PIN_NO(82) | 5)
-#define MT8135_PIN_82_MSDC2_DAT0__FUNC_DPI33_D4 (MTK_PIN_NO(82) | 6)
-
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_GPIO83 (MTK_PIN_NO(83) | 0)
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_MSDC1_DAT0 (MTK_PIN_NO(83) | 1)
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_EINT53 (MTK_PIN_NO(83) | 2)
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_SCL1 (MTK_PIN_NO(83) | 3)
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_PWM2 (MTK_PIN_NO(83) | 4)
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_CLKM1 (MTK_PIN_NO(83) | 5)
-#define MT8135_PIN_83_MSDC1_DAT0__FUNC_TESTB_OUT2 (MTK_PIN_NO(83) | 7)
-
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_GPIO84 (MTK_PIN_NO(84) | 0)
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_MSDC1_DAT1 (MTK_PIN_NO(84) | 1)
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_EINT54 (MTK_PIN_NO(84) | 2)
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_SDA1 (MTK_PIN_NO(84) | 3)
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_PWM3 (MTK_PIN_NO(84) | 4)
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_CLKM2 (MTK_PIN_NO(84) | 5)
-#define MT8135_PIN_84_MSDC1_DAT1__FUNC_TESTB_OUT3 (MTK_PIN_NO(84) | 7)
-
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_GPIO85 (MTK_PIN_NO(85) | 0)
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_MSDC1_CMD (MTK_PIN_NO(85) | 1)
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_EINT52 (MTK_PIN_NO(85) | 2)
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_SDA0 (MTK_PIN_NO(85) | 3)
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_PWM1 (MTK_PIN_NO(85) | 4)
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_CLKM0 (MTK_PIN_NO(85) | 5)
-#define MT8135_PIN_85_MSDC1_CMD__FUNC_TESTB_OUT1 (MTK_PIN_NO(85) | 7)
-
-#define MT8135_PIN_86_MSDC1_CLK__FUNC_GPIO86 (MTK_PIN_NO(86) | 0)
-#define MT8135_PIN_86_MSDC1_CLK__FUNC_MSDC1_CLK (MTK_PIN_NO(86) | 1)
-#define MT8135_PIN_86_MSDC1_CLK__FUNC_EINT51 (MTK_PIN_NO(86) | 2)
-#define MT8135_PIN_86_MSDC1_CLK__FUNC_SCL0 (MTK_PIN_NO(86) | 3)
-#define MT8135_PIN_86_MSDC1_CLK__FUNC_DISP_PWM (MTK_PIN_NO(86) | 4)
-#define MT8135_PIN_86_MSDC1_CLK__FUNC_TESTB_OUT0 (MTK_PIN_NO(86) | 7)
-
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_GPIO87 (MTK_PIN_NO(87) | 0)
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_MSDC1_DAT2 (MTK_PIN_NO(87) | 1)
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_EINT55 (MTK_PIN_NO(87) | 2)
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_SCL4 (MTK_PIN_NO(87) | 3)
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_PWM4 (MTK_PIN_NO(87) | 4)
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_CLKM3 (MTK_PIN_NO(87) | 5)
-#define MT8135_PIN_87_MSDC1_DAT2__FUNC_TESTB_OUT4 (MTK_PIN_NO(87) | 7)
-
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_GPIO88 (MTK_PIN_NO(88) | 0)
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_MSDC1_DAT3 (MTK_PIN_NO(88) | 1)
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_EINT56 (MTK_PIN_NO(88) | 2)
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_SDA4 (MTK_PIN_NO(88) | 3)
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_PWM5 (MTK_PIN_NO(88) | 4)
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_CLKM4 (MTK_PIN_NO(88) | 5)
-#define MT8135_PIN_88_MSDC1_DAT3__FUNC_TESTB_OUT5 (MTK_PIN_NO(88) | 7)
-
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_GPIO89 (MTK_PIN_NO(89) | 0)
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_MSDC4_DAT0 (MTK_PIN_NO(89) | 1)
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_EINT133 (MTK_PIN_NO(89) | 2)
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_EXT_FRAME_SYNC (MTK_PIN_NO(89) | 4)
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_USB_DRVVBUS (MTK_PIN_NO(89) | 5)
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_A_FUNC_DIN_9 (MTK_PIN_NO(89) | 6)
-#define MT8135_PIN_89_MSDC4_DAT0__FUNC_LPTE (MTK_PIN_NO(89) | 7)
-
-#define MT8135_PIN_90_MSDC4_DAT1__FUNC_GPIO90 (MTK_PIN_NO(90) | 0)
-#define MT8135_PIN_90_MSDC4_DAT1__FUNC_MSDC4_DAT1 (MTK_PIN_NO(90) | 1)
-#define MT8135_PIN_90_MSDC4_DAT1__FUNC_EINT134 (MTK_PIN_NO(90) | 2)
-#define MT8135_PIN_90_MSDC4_DAT1__FUNC_A_FUNC_DIN_10 (MTK_PIN_NO(90) | 6)
-#define MT8135_PIN_90_MSDC4_DAT1__FUNC_LRSTB_1X (MTK_PIN_NO(90) | 7)
-
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_GPIO91 (MTK_PIN_NO(91) | 0)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_MSDC4_DAT5 (MTK_PIN_NO(91) | 1)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_EINT136 (MTK_PIN_NO(91) | 2)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_I2SIN_WS (MTK_PIN_NO(91) | 3)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_DAC_WS (MTK_PIN_NO(91) | 4)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_PCM1_WS (MTK_PIN_NO(91) | 5)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_A_FUNC_DIN_11 (MTK_PIN_NO(91) | 6)
-#define MT8135_PIN_91_MSDC4_DAT5__FUNC_SPI1_CSN (MTK_PIN_NO(91) | 7)
-
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_GPIO92 (MTK_PIN_NO(92) | 0)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_MSDC4_DAT6 (MTK_PIN_NO(92) | 1)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_EINT137 (MTK_PIN_NO(92) | 2)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_I2SOUT_DAT (MTK_PIN_NO(92) | 3)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_DAC_DAT_OUT (MTK_PIN_NO(92) | 4)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_PCM1_DO (MTK_PIN_NO(92) | 5)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_A_FUNC_DIN_12 (MTK_PIN_NO(92) | 6)
-#define MT8135_PIN_92_MSDC4_DAT6__FUNC_SPI1_MO (MTK_PIN_NO(92) | 7)
-
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_GPIO93 (MTK_PIN_NO(93) | 0)
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_MSDC4_DAT7 (MTK_PIN_NO(93) | 1)
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_EINT138 (MTK_PIN_NO(93) | 2)
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_I2SIN_DAT (MTK_PIN_NO(93) | 3)
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_PCM1_DI (MTK_PIN_NO(93) | 5)
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_A_FUNC_DIN_13 (MTK_PIN_NO(93) | 6)
-#define MT8135_PIN_93_MSDC4_DAT7__FUNC_SPI1_MI (MTK_PIN_NO(93) | 7)
-
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_GPIO94 (MTK_PIN_NO(94) | 0)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_MSDC4_DAT4 (MTK_PIN_NO(94) | 1)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_EINT135 (MTK_PIN_NO(94) | 2)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_I2SIN_CK (MTK_PIN_NO(94) | 3)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_DAC_CK (MTK_PIN_NO(94) | 4)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_PCM1_CK (MTK_PIN_NO(94) | 5)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_A_FUNC_DIN_14 (MTK_PIN_NO(94) | 6)
-#define MT8135_PIN_94_MSDC4_DAT4__FUNC_SPI1_CLK (MTK_PIN_NO(94) | 7)
-
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_GPIO95 (MTK_PIN_NO(95) | 0)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_MSDC4_DAT2 (MTK_PIN_NO(95) | 1)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_EINT131 (MTK_PIN_NO(95) | 2)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_I2SIN_WS (MTK_PIN_NO(95) | 3)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_CM2PDN_2X (MTK_PIN_NO(95) | 4)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_DAC_WS (MTK_PIN_NO(95) | 5)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_PCM1_WS (MTK_PIN_NO(95) | 6)
-#define MT8135_PIN_95_MSDC4_DAT2__FUNC_LSCE0B_1X (MTK_PIN_NO(95) | 7)
-
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_GPIO96 (MTK_PIN_NO(96) | 0)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_MSDC4_CLK (MTK_PIN_NO(96) | 1)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_EINT129 (MTK_PIN_NO(96) | 2)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_DPI1_CK_2X (MTK_PIN_NO(96) | 3)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_CM2PCLK_2X (MTK_PIN_NO(96) | 4)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_PWM4 (MTK_PIN_NO(96) | 5)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_PCM1_DI (MTK_PIN_NO(96) | 6)
-#define MT8135_PIN_96_MSDC4_CLK__FUNC_LSCK_1X (MTK_PIN_NO(96) | 7)
-
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_GPIO97 (MTK_PIN_NO(97) | 0)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_MSDC4_DAT3 (MTK_PIN_NO(97) | 1)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_EINT132 (MTK_PIN_NO(97) | 2)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_I2SOUT_DAT (MTK_PIN_NO(97) | 3)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_CM2RST_2X (MTK_PIN_NO(97) | 4)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_DAC_DAT_OUT (MTK_PIN_NO(97) | 5)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_PCM1_DO (MTK_PIN_NO(97) | 6)
-#define MT8135_PIN_97_MSDC4_DAT3__FUNC_LSCE1B_1X (MTK_PIN_NO(97) | 7)
-
-#define MT8135_PIN_98_MSDC4_CMD__FUNC_GPIO98 (MTK_PIN_NO(98) | 0)
-#define MT8135_PIN_98_MSDC4_CMD__FUNC_MSDC4_CMD (MTK_PIN_NO(98) | 1)
-#define MT8135_PIN_98_MSDC4_CMD__FUNC_EINT128 (MTK_PIN_NO(98) | 2)
-#define MT8135_PIN_98_MSDC4_CMD__FUNC_DPI1_DE_2X (MTK_PIN_NO(98) | 3)
-#define MT8135_PIN_98_MSDC4_CMD__FUNC_PWM3 (MTK_PIN_NO(98) | 5)
-#define MT8135_PIN_98_MSDC4_CMD__FUNC_LSDA_1X (MTK_PIN_NO(98) | 7)
-
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_GPIO99 (MTK_PIN_NO(99) | 0)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_MSDC4_RSTB (MTK_PIN_NO(99) | 1)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_EINT130 (MTK_PIN_NO(99) | 2)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_I2SIN_CK (MTK_PIN_NO(99) | 3)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_CM2MCLK_2X (MTK_PIN_NO(99) | 4)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_DAC_CK (MTK_PIN_NO(99) | 5)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_PCM1_CK (MTK_PIN_NO(99) | 6)
-#define MT8135_PIN_99_MSDC4_RSTB__FUNC_LSA0_1X (MTK_PIN_NO(99) | 7)
-
-#define MT8135_PIN_100_SDA0__FUNC_GPIO100 (MTK_PIN_NO(100) | 0)
-#define MT8135_PIN_100_SDA0__FUNC_SDA0 (MTK_PIN_NO(100) | 1)
-#define MT8135_PIN_100_SDA0__FUNC_EINT91 (MTK_PIN_NO(100) | 2)
-#define MT8135_PIN_100_SDA0__FUNC_CLKM1 (MTK_PIN_NO(100) | 3)
-#define MT8135_PIN_100_SDA0__FUNC_PWM1 (MTK_PIN_NO(100) | 4)
-#define MT8135_PIN_100_SDA0__FUNC_A_FUNC_DIN_15 (MTK_PIN_NO(100) | 7)
-
-#define MT8135_PIN_101_SCL0__FUNC_GPIO101 (MTK_PIN_NO(101) | 0)
-#define MT8135_PIN_101_SCL0__FUNC_SCL0 (MTK_PIN_NO(101) | 1)
-#define MT8135_PIN_101_SCL0__FUNC_EINT90 (MTK_PIN_NO(101) | 2)
-#define MT8135_PIN_101_SCL0__FUNC_CLKM0 (MTK_PIN_NO(101) | 3)
-#define MT8135_PIN_101_SCL0__FUNC_DISP_PWM (MTK_PIN_NO(101) | 4)
-#define MT8135_PIN_101_SCL0__FUNC_A_FUNC_DIN_16 (MTK_PIN_NO(101) | 7)
-
-#define MT8135_PIN_102_EINT10_AUXIN2__FUNC_GPIO102 (MTK_PIN_NO(102) | 0)
-#define MT8135_PIN_102_EINT10_AUXIN2__FUNC_EINT10 (MTK_PIN_NO(102) | 1)
-#define MT8135_PIN_102_EINT10_AUXIN2__FUNC_USB_TEST_IO_16 (MTK_PIN_NO(102) | 5)
-#define MT8135_PIN_102_EINT10_AUXIN2__FUNC_TESTB_OUT16 (MTK_PIN_NO(102) | 6)
-#define MT8135_PIN_102_EINT10_AUXIN2__FUNC_A_FUNC_DIN_17 (MTK_PIN_NO(102) | 7)
-
-#define MT8135_PIN_103_EINT11_AUXIN3__FUNC_GPIO103 (MTK_PIN_NO(103) | 0)
-#define MT8135_PIN_103_EINT11_AUXIN3__FUNC_EINT11 (MTK_PIN_NO(103) | 1)
-#define MT8135_PIN_103_EINT11_AUXIN3__FUNC_USB_TEST_IO_17 (MTK_PIN_NO(103) | 5)
-#define MT8135_PIN_103_EINT11_AUXIN3__FUNC_TESTB_OUT17 (MTK_PIN_NO(103) | 6)
-#define MT8135_PIN_103_EINT11_AUXIN3__FUNC_A_FUNC_DIN_18 (MTK_PIN_NO(103) | 7)
-
-#define MT8135_PIN_104_EINT16_AUXIN4__FUNC_GPIO104 (MTK_PIN_NO(104) | 0)
-#define MT8135_PIN_104_EINT16_AUXIN4__FUNC_EINT16 (MTK_PIN_NO(104) | 1)
-#define MT8135_PIN_104_EINT16_AUXIN4__FUNC_USB_TEST_IO_18 (MTK_PIN_NO(104) | 5)
-#define MT8135_PIN_104_EINT16_AUXIN4__FUNC_TESTB_OUT18 (MTK_PIN_NO(104) | 6)
-#define MT8135_PIN_104_EINT16_AUXIN4__FUNC_A_FUNC_DIN_19 (MTK_PIN_NO(104) | 7)
-
-#define MT8135_PIN_105_I2S_CLK__FUNC_GPIO105 (MTK_PIN_NO(105) | 0)
-#define MT8135_PIN_105_I2S_CLK__FUNC_I2SIN_CK (MTK_PIN_NO(105) | 1)
-#define MT8135_PIN_105_I2S_CLK__FUNC_EINT10 (MTK_PIN_NO(105) | 2)
-#define MT8135_PIN_105_I2S_CLK__FUNC_DAC_CK (MTK_PIN_NO(105) | 3)
-#define MT8135_PIN_105_I2S_CLK__FUNC_PCM1_CK (MTK_PIN_NO(105) | 4)
-#define MT8135_PIN_105_I2S_CLK__FUNC_USB_TEST_IO_19 (MTK_PIN_NO(105) | 5)
-#define MT8135_PIN_105_I2S_CLK__FUNC_TESTB_OUT19 (MTK_PIN_NO(105) | 6)
-#define MT8135_PIN_105_I2S_CLK__FUNC_A_FUNC_DIN_20 (MTK_PIN_NO(105) | 7)
-
-#define MT8135_PIN_106_I2S_WS__FUNC_GPIO106 (MTK_PIN_NO(106) | 0)
-#define MT8135_PIN_106_I2S_WS__FUNC_I2SIN_WS (MTK_PIN_NO(106) | 1)
-#define MT8135_PIN_106_I2S_WS__FUNC_EINT13 (MTK_PIN_NO(106) | 2)
-#define MT8135_PIN_106_I2S_WS__FUNC_DAC_WS (MTK_PIN_NO(106) | 3)
-#define MT8135_PIN_106_I2S_WS__FUNC_PCM1_WS (MTK_PIN_NO(106) | 4)
-#define MT8135_PIN_106_I2S_WS__FUNC_USB_TEST_IO_20 (MTK_PIN_NO(106) | 5)
-#define MT8135_PIN_106_I2S_WS__FUNC_TESTB_OUT20 (MTK_PIN_NO(106) | 6)
-#define MT8135_PIN_106_I2S_WS__FUNC_A_FUNC_DIN_21 (MTK_PIN_NO(106) | 7)
-
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_GPIO107 (MTK_PIN_NO(107) | 0)
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_I2SIN_DAT (MTK_PIN_NO(107) | 1)
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_EINT11 (MTK_PIN_NO(107) | 2)
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_PCM1_DI (MTK_PIN_NO(107) | 4)
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_USB_TEST_IO_21 (MTK_PIN_NO(107) | 5)
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_TESTB_OUT22 (MTK_PIN_NO(107) | 6)
-#define MT8135_PIN_107_I2S_DATA_IN__FUNC_A_FUNC_DIN_22 (MTK_PIN_NO(107) | 7)
-
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_GPIO108 (MTK_PIN_NO(108) | 0)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_I2SOUT_DAT (MTK_PIN_NO(108) | 1)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_EINT12 (MTK_PIN_NO(108) | 2)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_DAC_DAT_OUT (MTK_PIN_NO(108) | 3)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_PCM1_DO (MTK_PIN_NO(108) | 4)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_USB_TEST_IO_22 (MTK_PIN_NO(108) | 5)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_TESTB_OUT23 (MTK_PIN_NO(108) | 6)
-#define MT8135_PIN_108_I2S_DATA_OUT__FUNC_A_FUNC_DIN_23 (MTK_PIN_NO(108) | 7)
-
-#define MT8135_PIN_109_EINT5__FUNC_GPIO109 (MTK_PIN_NO(109) | 0)
-#define MT8135_PIN_109_EINT5__FUNC_EINT5 (MTK_PIN_NO(109) | 1)
-#define MT8135_PIN_109_EINT5__FUNC_PWM5 (MTK_PIN_NO(109) | 2)
-#define MT8135_PIN_109_EINT5__FUNC_CLKM3 (MTK_PIN_NO(109) | 3)
-#define MT8135_PIN_109_EINT5__FUNC_GPU_JTRSTB (MTK_PIN_NO(109) | 4)
-#define MT8135_PIN_109_EINT5__FUNC_USB_TEST_IO_23 (MTK_PIN_NO(109) | 5)
-#define MT8135_PIN_109_EINT5__FUNC_TESTB_OUT26 (MTK_PIN_NO(109) | 6)
-#define MT8135_PIN_109_EINT5__FUNC_A_FUNC_DIN_24 (MTK_PIN_NO(109) | 7)
-
-#define MT8135_PIN_110_EINT6__FUNC_GPIO110 (MTK_PIN_NO(110) | 0)
-#define MT8135_PIN_110_EINT6__FUNC_EINT6 (MTK_PIN_NO(110) | 1)
-#define MT8135_PIN_110_EINT6__FUNC_PWM6 (MTK_PIN_NO(110) | 2)
-#define MT8135_PIN_110_EINT6__FUNC_CLKM4 (MTK_PIN_NO(110) | 3)
-#define MT8135_PIN_110_EINT6__FUNC_GPU_JTMS (MTK_PIN_NO(110) | 4)
-#define MT8135_PIN_110_EINT6__FUNC_USB_TEST_IO_24 (MTK_PIN_NO(110) | 5)
-#define MT8135_PIN_110_EINT6__FUNC_TESTB_OUT27 (MTK_PIN_NO(110) | 6)
-#define MT8135_PIN_110_EINT6__FUNC_A_FUNC_DIN_25 (MTK_PIN_NO(110) | 7)
-
-#define MT8135_PIN_111_EINT7__FUNC_GPIO111 (MTK_PIN_NO(111) | 0)
-#define MT8135_PIN_111_EINT7__FUNC_EINT7 (MTK_PIN_NO(111) | 1)
-#define MT8135_PIN_111_EINT7__FUNC_PWM7 (MTK_PIN_NO(111) | 2)
-#define MT8135_PIN_111_EINT7__FUNC_CLKM5 (MTK_PIN_NO(111) | 3)
-#define MT8135_PIN_111_EINT7__FUNC_GPU_JTDO (MTK_PIN_NO(111) | 4)
-#define MT8135_PIN_111_EINT7__FUNC_USB_TEST_IO_25 (MTK_PIN_NO(111) | 5)
-#define MT8135_PIN_111_EINT7__FUNC_TESTB_OUT28 (MTK_PIN_NO(111) | 6)
-#define MT8135_PIN_111_EINT7__FUNC_A_FUNC_DIN_26 (MTK_PIN_NO(111) | 7)
-
-#define MT8135_PIN_112_EINT8__FUNC_GPIO112 (MTK_PIN_NO(112) | 0)
-#define MT8135_PIN_112_EINT8__FUNC_EINT8 (MTK_PIN_NO(112) | 1)
-#define MT8135_PIN_112_EINT8__FUNC_DISP_PWM (MTK_PIN_NO(112) | 2)
-#define MT8135_PIN_112_EINT8__FUNC_CLKM6 (MTK_PIN_NO(112) | 3)
-#define MT8135_PIN_112_EINT8__FUNC_GPU_JTDI (MTK_PIN_NO(112) | 4)
-#define MT8135_PIN_112_EINT8__FUNC_USB_TEST_IO_26 (MTK_PIN_NO(112) | 5)
-#define MT8135_PIN_112_EINT8__FUNC_TESTB_OUT29 (MTK_PIN_NO(112) | 6)
-#define MT8135_PIN_112_EINT8__FUNC_EXT_FRAME_SYNC (MTK_PIN_NO(112) | 7)
-
-#define MT8135_PIN_113_EINT9__FUNC_GPIO113 (MTK_PIN_NO(113) | 0)
-#define MT8135_PIN_113_EINT9__FUNC_EINT9 (MTK_PIN_NO(113) | 1)
-#define MT8135_PIN_113_EINT9__FUNC_GPU_JTCK (MTK_PIN_NO(113) | 4)
-#define MT8135_PIN_113_EINT9__FUNC_USB_DRVVBUS (MTK_PIN_NO(113) | 5)
-#define MT8135_PIN_113_EINT9__FUNC_TESTB_OUT30 (MTK_PIN_NO(113) | 6)
-#define MT8135_PIN_113_EINT9__FUNC_A_FUNC_DIN_27 (MTK_PIN_NO(113) | 7)
-
-#define MT8135_PIN_114_LPCE1B__FUNC_GPIO114 (MTK_PIN_NO(114) | 0)
-#define MT8135_PIN_114_LPCE1B__FUNC_LPCE1B (MTK_PIN_NO(114) | 1)
-#define MT8135_PIN_114_LPCE1B__FUNC_EINT127 (MTK_PIN_NO(114) | 2)
-#define MT8135_PIN_114_LPCE1B__FUNC_PWM2 (MTK_PIN_NO(114) | 5)
-#define MT8135_PIN_114_LPCE1B__FUNC_TESTB_OUT14 (MTK_PIN_NO(114) | 6)
-#define MT8135_PIN_114_LPCE1B__FUNC_A_FUNC_DIN_28 (MTK_PIN_NO(114) | 7)
-
-#define MT8135_PIN_115_LPCE0B__FUNC_GPIO115 (MTK_PIN_NO(115) | 0)
-#define MT8135_PIN_115_LPCE0B__FUNC_LPCE0B (MTK_PIN_NO(115) | 1)
-#define MT8135_PIN_115_LPCE0B__FUNC_EINT126 (MTK_PIN_NO(115) | 2)
-#define MT8135_PIN_115_LPCE0B__FUNC_PWM1 (MTK_PIN_NO(115) | 5)
-#define MT8135_PIN_115_LPCE0B__FUNC_TESTB_OUT15 (MTK_PIN_NO(115) | 6)
-#define MT8135_PIN_115_LPCE0B__FUNC_A_FUNC_DIN_29 (MTK_PIN_NO(115) | 7)
-
-#define MT8135_PIN_116_DISP_PWM__FUNC_GPIO116 (MTK_PIN_NO(116) | 0)
-#define MT8135_PIN_116_DISP_PWM__FUNC_DISP_PWM (MTK_PIN_NO(116) | 1)
-#define MT8135_PIN_116_DISP_PWM__FUNC_EINT77 (MTK_PIN_NO(116) | 2)
-#define MT8135_PIN_116_DISP_PWM__FUNC_LSDI (MTK_PIN_NO(116) | 3)
-#define MT8135_PIN_116_DISP_PWM__FUNC_PWM1 (MTK_PIN_NO(116) | 4)
-#define MT8135_PIN_116_DISP_PWM__FUNC_PWM2 (MTK_PIN_NO(116) | 5)
-#define MT8135_PIN_116_DISP_PWM__FUNC_PWM3 (MTK_PIN_NO(116) | 7)
-
-#define MT8135_PIN_117_EINT1__FUNC_GPIO117 (MTK_PIN_NO(117) | 0)
-#define MT8135_PIN_117_EINT1__FUNC_EINT1 (MTK_PIN_NO(117) | 1)
-#define MT8135_PIN_117_EINT1__FUNC_PWM2 (MTK_PIN_NO(117) | 2)
-#define MT8135_PIN_117_EINT1__FUNC_CLKM1 (MTK_PIN_NO(117) | 3)
-#define MT8135_PIN_117_EINT1__FUNC_USB_TEST_IO_13 (MTK_PIN_NO(117) | 5)
-#define MT8135_PIN_117_EINT1__FUNC_USB_SDA (MTK_PIN_NO(117) | 7)
-
-#define MT8135_PIN_118_EINT2__FUNC_GPIO118 (MTK_PIN_NO(118) | 0)
-#define MT8135_PIN_118_EINT2__FUNC_EINT2 (MTK_PIN_NO(118) | 1)
-#define MT8135_PIN_118_EINT2__FUNC_PWM3 (MTK_PIN_NO(118) | 2)
-#define MT8135_PIN_118_EINT2__FUNC_CLKM2 (MTK_PIN_NO(118) | 3)
-#define MT8135_PIN_118_EINT2__FUNC_USB_TEST_IO_14 (MTK_PIN_NO(118) | 5)
-#define MT8135_PIN_118_EINT2__FUNC_SRCLKENAI2 (MTK_PIN_NO(118) | 6)
-#define MT8135_PIN_118_EINT2__FUNC_A_FUNC_DIN_30 (MTK_PIN_NO(118) | 7)
-
-#define MT8135_PIN_119_EINT3__FUNC_GPIO119 (MTK_PIN_NO(119) | 0)
-#define MT8135_PIN_119_EINT3__FUNC_EINT3 (MTK_PIN_NO(119) | 1)
-#define MT8135_PIN_119_EINT3__FUNC_USB_TEST_IO_15 (MTK_PIN_NO(119) | 5)
-#define MT8135_PIN_119_EINT3__FUNC_SRCLKENAI1 (MTK_PIN_NO(119) | 6)
-#define MT8135_PIN_119_EINT3__FUNC_EXT_26M_CK (MTK_PIN_NO(119) | 7)
-
-#define MT8135_PIN_120_EINT4__FUNC_GPIO120 (MTK_PIN_NO(120) | 0)
-#define MT8135_PIN_120_EINT4__FUNC_EINT4 (MTK_PIN_NO(120) | 1)
-#define MT8135_PIN_120_EINT4__FUNC_PWM4 (MTK_PIN_NO(120) | 2)
-#define MT8135_PIN_120_EINT4__FUNC_USB_DRVVBUS (MTK_PIN_NO(120) | 5)
-#define MT8135_PIN_120_EINT4__FUNC_A_FUNC_DIN_31 (MTK_PIN_NO(120) | 7)
-
-#define MT8135_PIN_121_DPIDE__FUNC_GPIO121 (MTK_PIN_NO(121) | 0)
-#define MT8135_PIN_121_DPIDE__FUNC_DPI0_DE (MTK_PIN_NO(121) | 1)
-#define MT8135_PIN_121_DPIDE__FUNC_EINT100 (MTK_PIN_NO(121) | 2)
-#define MT8135_PIN_121_DPIDE__FUNC_I2SOUT_DAT (MTK_PIN_NO(121) | 3)
-#define MT8135_PIN_121_DPIDE__FUNC_DAC_DAT_OUT (MTK_PIN_NO(121) | 4)
-#define MT8135_PIN_121_DPIDE__FUNC_PCM1_DO (MTK_PIN_NO(121) | 5)
-#define MT8135_PIN_121_DPIDE__FUNC_IRDA_TXD (MTK_PIN_NO(121) | 6)
-
-#define MT8135_PIN_122_DPICK__FUNC_GPIO122 (MTK_PIN_NO(122) | 0)
-#define MT8135_PIN_122_DPICK__FUNC_DPI0_CK (MTK_PIN_NO(122) | 1)
-#define MT8135_PIN_122_DPICK__FUNC_EINT101 (MTK_PIN_NO(122) | 2)
-#define MT8135_PIN_122_DPICK__FUNC_I2SIN_DAT (MTK_PIN_NO(122) | 3)
-#define MT8135_PIN_122_DPICK__FUNC_PCM1_DI (MTK_PIN_NO(122) | 5)
-#define MT8135_PIN_122_DPICK__FUNC_IRDA_PDN (MTK_PIN_NO(122) | 6)
-
-#define MT8135_PIN_123_DPIG4__FUNC_GPIO123 (MTK_PIN_NO(123) | 0)
-#define MT8135_PIN_123_DPIG4__FUNC_DPI0_G4 (MTK_PIN_NO(123) | 1)
-#define MT8135_PIN_123_DPIG4__FUNC_EINT114 (MTK_PIN_NO(123) | 2)
-#define MT8135_PIN_123_DPIG4__FUNC_CM2DAT_2X_0 (MTK_PIN_NO(123) | 4)
-#define MT8135_PIN_123_DPIG4__FUNC_DSP2_ID (MTK_PIN_NO(123) | 5)
-
-#define MT8135_PIN_124_DPIG5__FUNC_GPIO124 (MTK_PIN_NO(124) | 0)
-#define MT8135_PIN_124_DPIG5__FUNC_DPI0_G5 (MTK_PIN_NO(124) | 1)
-#define MT8135_PIN_124_DPIG5__FUNC_EINT115 (MTK_PIN_NO(124) | 2)
-#define MT8135_PIN_124_DPIG5__FUNC_CM2DAT_2X_1 (MTK_PIN_NO(124) | 4)
-#define MT8135_PIN_124_DPIG5__FUNC_DSP2_ICK (MTK_PIN_NO(124) | 5)
-
-#define MT8135_PIN_125_DPIR3__FUNC_GPIO125 (MTK_PIN_NO(125) | 0)
-#define MT8135_PIN_125_DPIR3__FUNC_DPI0_R3 (MTK_PIN_NO(125) | 1)
-#define MT8135_PIN_125_DPIR3__FUNC_EINT121 (MTK_PIN_NO(125) | 2)
-#define MT8135_PIN_125_DPIR3__FUNC_CM2DAT_2X_7 (MTK_PIN_NO(125) | 4)
-
-#define MT8135_PIN_126_DPIG1__FUNC_GPIO126 (MTK_PIN_NO(126) | 0)
-#define MT8135_PIN_126_DPIG1__FUNC_DPI0_G1 (MTK_PIN_NO(126) | 1)
-#define MT8135_PIN_126_DPIG1__FUNC_EINT111 (MTK_PIN_NO(126) | 2)
-#define MT8135_PIN_126_DPIG1__FUNC_DSP1_ICK (MTK_PIN_NO(126) | 5)
-
-#define MT8135_PIN_127_DPIVSYNC__FUNC_GPIO127 (MTK_PIN_NO(127) | 0)
-#define MT8135_PIN_127_DPIVSYNC__FUNC_DPI0_VSYNC (MTK_PIN_NO(127) | 1)
-#define MT8135_PIN_127_DPIVSYNC__FUNC_EINT98 (MTK_PIN_NO(127) | 2)
-#define MT8135_PIN_127_DPIVSYNC__FUNC_I2SIN_CK (MTK_PIN_NO(127) | 3)
-#define MT8135_PIN_127_DPIVSYNC__FUNC_DAC_CK (MTK_PIN_NO(127) | 4)
-#define MT8135_PIN_127_DPIVSYNC__FUNC_PCM1_CK (MTK_PIN_NO(127) | 5)
-
-#define MT8135_PIN_128_DPIHSYNC__FUNC_GPIO128 (MTK_PIN_NO(128) | 0)
-#define MT8135_PIN_128_DPIHSYNC__FUNC_DPI0_HSYNC (MTK_PIN_NO(128) | 1)
-#define MT8135_PIN_128_DPIHSYNC__FUNC_EINT99 (MTK_PIN_NO(128) | 2)
-#define MT8135_PIN_128_DPIHSYNC__FUNC_I2SIN_WS (MTK_PIN_NO(128) | 3)
-#define MT8135_PIN_128_DPIHSYNC__FUNC_DAC_WS (MTK_PIN_NO(128) | 4)
-#define MT8135_PIN_128_DPIHSYNC__FUNC_PCM1_WS (MTK_PIN_NO(128) | 5)
-#define MT8135_PIN_128_DPIHSYNC__FUNC_IRDA_RXD (MTK_PIN_NO(128) | 6)
-
-#define MT8135_PIN_129_DPIB0__FUNC_GPIO129 (MTK_PIN_NO(129) | 0)
-#define MT8135_PIN_129_DPIB0__FUNC_DPI0_B0 (MTK_PIN_NO(129) | 1)
-#define MT8135_PIN_129_DPIB0__FUNC_EINT102 (MTK_PIN_NO(129) | 2)
-#define MT8135_PIN_129_DPIB0__FUNC_SCL0 (MTK_PIN_NO(129) | 4)
-#define MT8135_PIN_129_DPIB0__FUNC_DISP_PWM (MTK_PIN_NO(129) | 5)
-
-#define MT8135_PIN_130_DPIB1__FUNC_GPIO130 (MTK_PIN_NO(130) | 0)
-#define MT8135_PIN_130_DPIB1__FUNC_DPI0_B1 (MTK_PIN_NO(130) | 1)
-#define MT8135_PIN_130_DPIB1__FUNC_EINT103 (MTK_PIN_NO(130) | 2)
-#define MT8135_PIN_130_DPIB1__FUNC_CLKM0 (MTK_PIN_NO(130) | 3)
-#define MT8135_PIN_130_DPIB1__FUNC_SDA0 (MTK_PIN_NO(130) | 4)
-#define MT8135_PIN_130_DPIB1__FUNC_PWM1 (MTK_PIN_NO(130) | 5)
-
-#define MT8135_PIN_131_DPIB2__FUNC_GPIO131 (MTK_PIN_NO(131) | 0)
-#define MT8135_PIN_131_DPIB2__FUNC_DPI0_B2 (MTK_PIN_NO(131) | 1)
-#define MT8135_PIN_131_DPIB2__FUNC_EINT104 (MTK_PIN_NO(131) | 2)
-#define MT8135_PIN_131_DPIB2__FUNC_CLKM1 (MTK_PIN_NO(131) | 3)
-#define MT8135_PIN_131_DPIB2__FUNC_SCL1 (MTK_PIN_NO(131) | 4)
-#define MT8135_PIN_131_DPIB2__FUNC_PWM2 (MTK_PIN_NO(131) | 5)
-
-#define MT8135_PIN_132_DPIB3__FUNC_GPIO132 (MTK_PIN_NO(132) | 0)
-#define MT8135_PIN_132_DPIB3__FUNC_DPI0_B3 (MTK_PIN_NO(132) | 1)
-#define MT8135_PIN_132_DPIB3__FUNC_EINT105 (MTK_PIN_NO(132) | 2)
-#define MT8135_PIN_132_DPIB3__FUNC_CLKM2 (MTK_PIN_NO(132) | 3)
-#define MT8135_PIN_132_DPIB3__FUNC_SDA1 (MTK_PIN_NO(132) | 4)
-#define MT8135_PIN_132_DPIB3__FUNC_PWM3 (MTK_PIN_NO(132) | 5)
-
-#define MT8135_PIN_133_DPIB4__FUNC_GPIO133 (MTK_PIN_NO(133) | 0)
-#define MT8135_PIN_133_DPIB4__FUNC_DPI0_B4 (MTK_PIN_NO(133) | 1)
-#define MT8135_PIN_133_DPIB4__FUNC_EINT106 (MTK_PIN_NO(133) | 2)
-#define MT8135_PIN_133_DPIB4__FUNC_CLKM3 (MTK_PIN_NO(133) | 3)
-#define MT8135_PIN_133_DPIB4__FUNC_SCL2 (MTK_PIN_NO(133) | 4)
-#define MT8135_PIN_133_DPIB4__FUNC_PWM4 (MTK_PIN_NO(133) | 5)
-
-#define MT8135_PIN_134_DPIB5__FUNC_GPIO134 (MTK_PIN_NO(134) | 0)
-#define MT8135_PIN_134_DPIB5__FUNC_DPI0_B5 (MTK_PIN_NO(134) | 1)
-#define MT8135_PIN_134_DPIB5__FUNC_EINT107 (MTK_PIN_NO(134) | 2)
-#define MT8135_PIN_134_DPIB5__FUNC_CLKM4 (MTK_PIN_NO(134) | 3)
-#define MT8135_PIN_134_DPIB5__FUNC_SDA2 (MTK_PIN_NO(134) | 4)
-#define MT8135_PIN_134_DPIB5__FUNC_PWM5 (MTK_PIN_NO(134) | 5)
-
-#define MT8135_PIN_135_DPIB6__FUNC_GPIO135 (MTK_PIN_NO(135) | 0)
-#define MT8135_PIN_135_DPIB6__FUNC_DPI0_B6 (MTK_PIN_NO(135) | 1)
-#define MT8135_PIN_135_DPIB6__FUNC_EINT108 (MTK_PIN_NO(135) | 2)
-#define MT8135_PIN_135_DPIB6__FUNC_CLKM5 (MTK_PIN_NO(135) | 3)
-#define MT8135_PIN_135_DPIB6__FUNC_SCL3 (MTK_PIN_NO(135) | 4)
-#define MT8135_PIN_135_DPIB6__FUNC_PWM6 (MTK_PIN_NO(135) | 5)
-
-#define MT8135_PIN_136_DPIB7__FUNC_GPIO136 (MTK_PIN_NO(136) | 0)
-#define MT8135_PIN_136_DPIB7__FUNC_DPI0_B7 (MTK_PIN_NO(136) | 1)
-#define MT8135_PIN_136_DPIB7__FUNC_EINT109 (MTK_PIN_NO(136) | 2)
-#define MT8135_PIN_136_DPIB7__FUNC_CLKM6 (MTK_PIN_NO(136) | 3)
-#define MT8135_PIN_136_DPIB7__FUNC_SDA3 (MTK_PIN_NO(136) | 4)
-#define MT8135_PIN_136_DPIB7__FUNC_PWM7 (MTK_PIN_NO(136) | 5)
-
-#define MT8135_PIN_137_DPIG0__FUNC_GPIO137 (MTK_PIN_NO(137) | 0)
-#define MT8135_PIN_137_DPIG0__FUNC_DPI0_G0 (MTK_PIN_NO(137) | 1)
-#define MT8135_PIN_137_DPIG0__FUNC_EINT110 (MTK_PIN_NO(137) | 2)
-#define MT8135_PIN_137_DPIG0__FUNC_DSP1_ID (MTK_PIN_NO(137) | 5)
-
-#define MT8135_PIN_138_DPIG2__FUNC_GPIO138 (MTK_PIN_NO(138) | 0)
-#define MT8135_PIN_138_DPIG2__FUNC_DPI0_G2 (MTK_PIN_NO(138) | 1)
-#define MT8135_PIN_138_DPIG2__FUNC_EINT112 (MTK_PIN_NO(138) | 2)
-#define MT8135_PIN_138_DPIG2__FUNC_DSP1_IMS (MTK_PIN_NO(138) | 5)
-
-#define MT8135_PIN_139_DPIG3__FUNC_GPIO139 (MTK_PIN_NO(139) | 0)
-#define MT8135_PIN_139_DPIG3__FUNC_DPI0_G3 (MTK_PIN_NO(139) | 1)
-#define MT8135_PIN_139_DPIG3__FUNC_EINT113 (MTK_PIN_NO(139) | 2)
-#define MT8135_PIN_139_DPIG3__FUNC_DSP2_IMS (MTK_PIN_NO(139) | 5)
-
-#define MT8135_PIN_140_DPIG6__FUNC_GPIO140 (MTK_PIN_NO(140) | 0)
-#define MT8135_PIN_140_DPIG6__FUNC_DPI0_G6 (MTK_PIN_NO(140) | 1)
-#define MT8135_PIN_140_DPIG6__FUNC_EINT116 (MTK_PIN_NO(140) | 2)
-#define MT8135_PIN_140_DPIG6__FUNC_CM2DAT_2X_2 (MTK_PIN_NO(140) | 4)
-
-#define MT8135_PIN_141_DPIG7__FUNC_GPIO141 (MTK_PIN_NO(141) | 0)
-#define MT8135_PIN_141_DPIG7__FUNC_DPI0_G7 (MTK_PIN_NO(141) | 1)
-#define MT8135_PIN_141_DPIG7__FUNC_EINT117 (MTK_PIN_NO(141) | 2)
-#define MT8135_PIN_141_DPIG7__FUNC_CM2DAT_2X_3 (MTK_PIN_NO(141) | 4)
-
-#define MT8135_PIN_142_DPIR0__FUNC_GPIO142 (MTK_PIN_NO(142) | 0)
-#define MT8135_PIN_142_DPIR0__FUNC_DPI0_R0 (MTK_PIN_NO(142) | 1)
-#define MT8135_PIN_142_DPIR0__FUNC_EINT118 (MTK_PIN_NO(142) | 2)
-#define MT8135_PIN_142_DPIR0__FUNC_CM2DAT_2X_4 (MTK_PIN_NO(142) | 4)
-
-#define MT8135_PIN_143_DPIR1__FUNC_GPIO143 (MTK_PIN_NO(143) | 0)
-#define MT8135_PIN_143_DPIR1__FUNC_DPI0_R1 (MTK_PIN_NO(143) | 1)
-#define MT8135_PIN_143_DPIR1__FUNC_EINT119 (MTK_PIN_NO(143) | 2)
-#define MT8135_PIN_143_DPIR1__FUNC_CM2DAT_2X_5 (MTK_PIN_NO(143) | 4)
-
-#define MT8135_PIN_144_DPIR2__FUNC_GPIO144 (MTK_PIN_NO(144) | 0)
-#define MT8135_PIN_144_DPIR2__FUNC_DPI0_R2 (MTK_PIN_NO(144) | 1)
-#define MT8135_PIN_144_DPIR2__FUNC_EINT120 (MTK_PIN_NO(144) | 2)
-#define MT8135_PIN_144_DPIR2__FUNC_CM2DAT_2X_6 (MTK_PIN_NO(144) | 4)
-
-#define MT8135_PIN_145_DPIR4__FUNC_GPIO145 (MTK_PIN_NO(145) | 0)
-#define MT8135_PIN_145_DPIR4__FUNC_DPI0_R4 (MTK_PIN_NO(145) | 1)
-#define MT8135_PIN_145_DPIR4__FUNC_EINT122 (MTK_PIN_NO(145) | 2)
-#define MT8135_PIN_145_DPIR4__FUNC_CM2DAT_2X_8 (MTK_PIN_NO(145) | 4)
-
-#define MT8135_PIN_146_DPIR5__FUNC_GPIO146 (MTK_PIN_NO(146) | 0)
-#define MT8135_PIN_146_DPIR5__FUNC_DPI0_R5 (MTK_PIN_NO(146) | 1)
-#define MT8135_PIN_146_DPIR5__FUNC_EINT123 (MTK_PIN_NO(146) | 2)
-#define MT8135_PIN_146_DPIR5__FUNC_CM2DAT_2X_9 (MTK_PIN_NO(146) | 4)
-
-#define MT8135_PIN_147_DPIR6__FUNC_GPIO147 (MTK_PIN_NO(147) | 0)
-#define MT8135_PIN_147_DPIR6__FUNC_DPI0_R6 (MTK_PIN_NO(147) | 1)
-#define MT8135_PIN_147_DPIR6__FUNC_EINT124 (MTK_PIN_NO(147) | 2)
-#define MT8135_PIN_147_DPIR6__FUNC_CM2VSYNC_2X (MTK_PIN_NO(147) | 4)
-
-#define MT8135_PIN_148_DPIR7__FUNC_GPIO148 (MTK_PIN_NO(148) | 0)
-#define MT8135_PIN_148_DPIR7__FUNC_DPI0_R7 (MTK_PIN_NO(148) | 1)
-#define MT8135_PIN_148_DPIR7__FUNC_EINT125 (MTK_PIN_NO(148) | 2)
-#define MT8135_PIN_148_DPIR7__FUNC_CM2HSYNC_2X (MTK_PIN_NO(148) | 4)
-
-#define MT8135_PIN_149_TDN3__FUNC_GPIO149 (MTK_PIN_NO(149) | 0)
-#define MT8135_PIN_149_TDN3__FUNC_EINT36 (MTK_PIN_NO(149) | 2)
-
-#define MT8135_PIN_150_TDP3__FUNC_GPIO150 (MTK_PIN_NO(150) | 0)
-#define MT8135_PIN_150_TDP3__FUNC_EINT35 (MTK_PIN_NO(150) | 2)
-
-#define MT8135_PIN_151_TDN2__FUNC_GPIO151 (MTK_PIN_NO(151) | 0)
-#define MT8135_PIN_151_TDN2__FUNC_EINT169 (MTK_PIN_NO(151) | 2)
-
-#define MT8135_PIN_152_TDP2__FUNC_GPIO152 (MTK_PIN_NO(152) | 0)
-#define MT8135_PIN_152_TDP2__FUNC_EINT168 (MTK_PIN_NO(152) | 2)
-
-#define MT8135_PIN_153_TCN__FUNC_GPIO153 (MTK_PIN_NO(153) | 0)
-#define MT8135_PIN_153_TCN__FUNC_EINT163 (MTK_PIN_NO(153) | 2)
-
-#define MT8135_PIN_154_TCP__FUNC_GPIO154 (MTK_PIN_NO(154) | 0)
-#define MT8135_PIN_154_TCP__FUNC_EINT162 (MTK_PIN_NO(154) | 2)
-
-#define MT8135_PIN_155_TDN1__FUNC_GPIO155 (MTK_PIN_NO(155) | 0)
-#define MT8135_PIN_155_TDN1__FUNC_EINT167 (MTK_PIN_NO(155) | 2)
-
-#define MT8135_PIN_156_TDP1__FUNC_GPIO156 (MTK_PIN_NO(156) | 0)
-#define MT8135_PIN_156_TDP1__FUNC_EINT166 (MTK_PIN_NO(156) | 2)
-
-#define MT8135_PIN_157_TDN0__FUNC_GPIO157 (MTK_PIN_NO(157) | 0)
-#define MT8135_PIN_157_TDN0__FUNC_EINT165 (MTK_PIN_NO(157) | 2)
-
-#define MT8135_PIN_158_TDP0__FUNC_GPIO158 (MTK_PIN_NO(158) | 0)
-#define MT8135_PIN_158_TDP0__FUNC_EINT164 (MTK_PIN_NO(158) | 2)
-
-#define MT8135_PIN_159_RDN3__FUNC_GPIO159 (MTK_PIN_NO(159) | 0)
-#define MT8135_PIN_159_RDN3__FUNC_EINT18 (MTK_PIN_NO(159) | 2)
-
-#define MT8135_PIN_160_RDP3__FUNC_GPIO160 (MTK_PIN_NO(160) | 0)
-#define MT8135_PIN_160_RDP3__FUNC_EINT30 (MTK_PIN_NO(160) | 2)
-
-#define MT8135_PIN_161_RDN2__FUNC_GPIO161 (MTK_PIN_NO(161) | 0)
-#define MT8135_PIN_161_RDN2__FUNC_EINT31 (MTK_PIN_NO(161) | 2)
-
-#define MT8135_PIN_162_RDP2__FUNC_GPIO162 (MTK_PIN_NO(162) | 0)
-#define MT8135_PIN_162_RDP2__FUNC_EINT32 (MTK_PIN_NO(162) | 2)
-
-#define MT8135_PIN_163_RCN__FUNC_GPIO163 (MTK_PIN_NO(163) | 0)
-#define MT8135_PIN_163_RCN__FUNC_EINT33 (MTK_PIN_NO(163) | 2)
-
-#define MT8135_PIN_164_RCP__FUNC_GPIO164 (MTK_PIN_NO(164) | 0)
-#define MT8135_PIN_164_RCP__FUNC_EINT39 (MTK_PIN_NO(164) | 2)
-
-#define MT8135_PIN_165_RDN1__FUNC_GPIO165 (MTK_PIN_NO(165) | 0)
-
-#define MT8135_PIN_166_RDP1__FUNC_GPIO166 (MTK_PIN_NO(166) | 0)
-
-#define MT8135_PIN_167_RDN0__FUNC_GPIO167 (MTK_PIN_NO(167) | 0)
-
-#define MT8135_PIN_168_RDP0__FUNC_GPIO168 (MTK_PIN_NO(168) | 0)
-
-#define MT8135_PIN_169_RDN1_A__FUNC_GPIO169 (MTK_PIN_NO(169) | 0)
-#define MT8135_PIN_169_RDN1_A__FUNC_CMDAT6 (MTK_PIN_NO(169) | 1)
-#define MT8135_PIN_169_RDN1_A__FUNC_EINT175 (MTK_PIN_NO(169) | 2)
-
-#define MT8135_PIN_170_RDP1_A__FUNC_GPIO170 (MTK_PIN_NO(170) | 0)
-#define MT8135_PIN_170_RDP1_A__FUNC_CMDAT7 (MTK_PIN_NO(170) | 1)
-#define MT8135_PIN_170_RDP1_A__FUNC_EINT174 (MTK_PIN_NO(170) | 2)
-
-#define MT8135_PIN_171_RCN_A__FUNC_GPIO171 (MTK_PIN_NO(171) | 0)
-#define MT8135_PIN_171_RCN_A__FUNC_CMDAT8 (MTK_PIN_NO(171) | 1)
-#define MT8135_PIN_171_RCN_A__FUNC_EINT171 (MTK_PIN_NO(171) | 2)
-
-#define MT8135_PIN_172_RCP_A__FUNC_GPIO172 (MTK_PIN_NO(172) | 0)
-#define MT8135_PIN_172_RCP_A__FUNC_CMDAT9 (MTK_PIN_NO(172) | 1)
-#define MT8135_PIN_172_RCP_A__FUNC_EINT170 (MTK_PIN_NO(172) | 2)
-
-#define MT8135_PIN_173_RDN0_A__FUNC_GPIO173 (MTK_PIN_NO(173) | 0)
-#define MT8135_PIN_173_RDN0_A__FUNC_CMHSYNC (MTK_PIN_NO(173) | 1)
-#define MT8135_PIN_173_RDN0_A__FUNC_EINT173 (MTK_PIN_NO(173) | 2)
-
-#define MT8135_PIN_174_RDP0_A__FUNC_GPIO174 (MTK_PIN_NO(174) | 0)
-#define MT8135_PIN_174_RDP0_A__FUNC_CMVSYNC (MTK_PIN_NO(174) | 1)
-#define MT8135_PIN_174_RDP0_A__FUNC_EINT172 (MTK_PIN_NO(174) | 2)
-
-#define MT8135_PIN_175_RDN1_B__FUNC_GPIO175 (MTK_PIN_NO(175) | 0)
-#define MT8135_PIN_175_RDN1_B__FUNC_CMDAT2 (MTK_PIN_NO(175) | 1)
-#define MT8135_PIN_175_RDN1_B__FUNC_EINT181 (MTK_PIN_NO(175) | 2)
-#define MT8135_PIN_175_RDN1_B__FUNC_CMCSD2 (MTK_PIN_NO(175) | 3)
-
-#define MT8135_PIN_176_RDP1_B__FUNC_GPIO176 (MTK_PIN_NO(176) | 0)
-#define MT8135_PIN_176_RDP1_B__FUNC_CMDAT3 (MTK_PIN_NO(176) | 1)
-#define MT8135_PIN_176_RDP1_B__FUNC_EINT180 (MTK_PIN_NO(176) | 2)
-#define MT8135_PIN_176_RDP1_B__FUNC_CMCSD3 (MTK_PIN_NO(176) | 3)
-
-#define MT8135_PIN_177_RCN_B__FUNC_GPIO177 (MTK_PIN_NO(177) | 0)
-#define MT8135_PIN_177_RCN_B__FUNC_CMDAT4 (MTK_PIN_NO(177) | 1)
-#define MT8135_PIN_177_RCN_B__FUNC_EINT177 (MTK_PIN_NO(177) | 2)
-
-#define MT8135_PIN_178_RCP_B__FUNC_GPIO178 (MTK_PIN_NO(178) | 0)
-#define MT8135_PIN_178_RCP_B__FUNC_CMDAT5 (MTK_PIN_NO(178) | 1)
-#define MT8135_PIN_178_RCP_B__FUNC_EINT176 (MTK_PIN_NO(178) | 2)
-
-#define MT8135_PIN_179_RDN0_B__FUNC_GPIO179 (MTK_PIN_NO(179) | 0)
-#define MT8135_PIN_179_RDN0_B__FUNC_CMDAT0 (MTK_PIN_NO(179) | 1)
-#define MT8135_PIN_179_RDN0_B__FUNC_EINT179 (MTK_PIN_NO(179) | 2)
-#define MT8135_PIN_179_RDN0_B__FUNC_CMCSD0 (MTK_PIN_NO(179) | 3)
-
-#define MT8135_PIN_180_RDP0_B__FUNC_GPIO180 (MTK_PIN_NO(180) | 0)
-#define MT8135_PIN_180_RDP0_B__FUNC_CMDAT1 (MTK_PIN_NO(180) | 1)
-#define MT8135_PIN_180_RDP0_B__FUNC_EINT178 (MTK_PIN_NO(180) | 2)
-#define MT8135_PIN_180_RDP0_B__FUNC_CMCSD1 (MTK_PIN_NO(180) | 3)
-
-#define MT8135_PIN_181_CMPCLK__FUNC_GPIO181 (MTK_PIN_NO(181) | 0)
-#define MT8135_PIN_181_CMPCLK__FUNC_CMPCLK (MTK_PIN_NO(181) | 1)
-#define MT8135_PIN_181_CMPCLK__FUNC_EINT182 (MTK_PIN_NO(181) | 2)
-#define MT8135_PIN_181_CMPCLK__FUNC_CMCSK (MTK_PIN_NO(181) | 3)
-#define MT8135_PIN_181_CMPCLK__FUNC_CM2MCLK_4X (MTK_PIN_NO(181) | 4)
-#define MT8135_PIN_181_CMPCLK__FUNC_TS_AUXADC_SEL_3 (MTK_PIN_NO(181) | 5)
-#define MT8135_PIN_181_CMPCLK__FUNC_VENC_TEST_CK (MTK_PIN_NO(181) | 6)
-#define MT8135_PIN_181_CMPCLK__FUNC_TESTA_OUT27 (MTK_PIN_NO(181) | 7)
-
-#define MT8135_PIN_182_CMMCLK__FUNC_GPIO182 (MTK_PIN_NO(182) | 0)
-#define MT8135_PIN_182_CMMCLK__FUNC_CMMCLK (MTK_PIN_NO(182) | 1)
-#define MT8135_PIN_182_CMMCLK__FUNC_EINT183 (MTK_PIN_NO(182) | 2)
-#define MT8135_PIN_182_CMMCLK__FUNC_TS_AUXADC_SEL_2 (MTK_PIN_NO(182) | 5)
-#define MT8135_PIN_182_CMMCLK__FUNC_TESTA_OUT28 (MTK_PIN_NO(182) | 7)
-
-#define MT8135_PIN_183_CMRST__FUNC_GPIO183 (MTK_PIN_NO(183) | 0)
-#define MT8135_PIN_183_CMRST__FUNC_CMRST (MTK_PIN_NO(183) | 1)
-#define MT8135_PIN_183_CMRST__FUNC_EINT185 (MTK_PIN_NO(183) | 2)
-#define MT8135_PIN_183_CMRST__FUNC_TS_AUXADC_SEL_1 (MTK_PIN_NO(183) | 5)
-#define MT8135_PIN_183_CMRST__FUNC_TESTA_OUT30 (MTK_PIN_NO(183) | 7)
-
-#define MT8135_PIN_184_CMPDN__FUNC_GPIO184 (MTK_PIN_NO(184) | 0)
-#define MT8135_PIN_184_CMPDN__FUNC_CMPDN (MTK_PIN_NO(184) | 1)
-#define MT8135_PIN_184_CMPDN__FUNC_EINT184 (MTK_PIN_NO(184) | 2)
-#define MT8135_PIN_184_CMPDN__FUNC_TS_AUXADC_SEL_0 (MTK_PIN_NO(184) | 5)
-#define MT8135_PIN_184_CMPDN__FUNC_TESTA_OUT29 (MTK_PIN_NO(184) | 7)
-
-#define MT8135_PIN_185_CMFLASH__FUNC_GPIO185 (MTK_PIN_NO(185) | 0)
-#define MT8135_PIN_185_CMFLASH__FUNC_CMFLASH (MTK_PIN_NO(185) | 1)
-#define MT8135_PIN_185_CMFLASH__FUNC_EINT186 (MTK_PIN_NO(185) | 2)
-#define MT8135_PIN_185_CMFLASH__FUNC_CM2MCLK_3X (MTK_PIN_NO(185) | 3)
-#define MT8135_PIN_185_CMFLASH__FUNC_MFG_TEST_CK_1 (MTK_PIN_NO(185) | 6)
-#define MT8135_PIN_185_CMFLASH__FUNC_TESTA_OUT31 (MTK_PIN_NO(185) | 7)
-
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_GPIO186 (MTK_PIN_NO(186) | 0)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_MRG_I2S_P_CLK (MTK_PIN_NO(186) | 1)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_EINT14 (MTK_PIN_NO(186) | 2)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_I2SIN_CK (MTK_PIN_NO(186) | 3)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_PCM0_CK (MTK_PIN_NO(186) | 4)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_DSP2_ICK (MTK_PIN_NO(186) | 5)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_IMG_TEST_CK (MTK_PIN_NO(186) | 6)
-#define MT8135_PIN_186_MRG_I2S_PCM_CLK__FUNC_USB_SCL (MTK_PIN_NO(186) | 7)
-
-#define MT8135_PIN_187_MRG_I2S_PCM_SYNC__FUNC_GPIO187 (MTK_PIN_NO(187) | 0)
-#define MT8135_PIN_187_MRG_I2S_PCM_SYNC__FUNC_MRG_I2S_SYNC (MTK_PIN_NO(187) | 1)
-#define MT8135_PIN_187_MRG_I2S_PCM_SYNC__FUNC_EINT16 (MTK_PIN_NO(187) | 2)
-#define MT8135_PIN_187_MRG_I2S_PCM_SYNC__FUNC_I2SIN_WS (MTK_PIN_NO(187) | 3)
-#define MT8135_PIN_187_MRG_I2S_PCM_SYNC__FUNC_PCM0_WS (MTK_PIN_NO(187) | 4)
-#define MT8135_PIN_187_MRG_I2S_PCM_SYNC__FUNC_DISP_TEST_CK (MTK_PIN_NO(187) | 6)
-
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_GPIO188 (MTK_PIN_NO(188) | 0)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_MRG_I2S_PCM_RX (MTK_PIN_NO(188) | 1)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_EINT15 (MTK_PIN_NO(188) | 2)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_I2SIN_DAT (MTK_PIN_NO(188) | 3)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_PCM0_DI (MTK_PIN_NO(188) | 4)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_DSP2_ID (MTK_PIN_NO(188) | 5)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_MFG_TEST_CK (MTK_PIN_NO(188) | 6)
-#define MT8135_PIN_188_MRG_I2S_PCM_RX__FUNC_USB_SDA (MTK_PIN_NO(188) | 7)
-
-#define MT8135_PIN_189_MRG_I2S_PCM_TX__FUNC_GPIO189 (MTK_PIN_NO(189) | 0)
-#define MT8135_PIN_189_MRG_I2S_PCM_TX__FUNC_MRG_I2S_PCM_TX (MTK_PIN_NO(189) | 1)
-#define MT8135_PIN_189_MRG_I2S_PCM_TX__FUNC_EINT17 (MTK_PIN_NO(189) | 2)
-#define MT8135_PIN_189_MRG_I2S_PCM_TX__FUNC_I2SOUT_DAT (MTK_PIN_NO(189) | 3)
-#define MT8135_PIN_189_MRG_I2S_PCM_TX__FUNC_PCM0_DO (MTK_PIN_NO(189) | 4)
-#define MT8135_PIN_189_MRG_I2S_PCM_TX__FUNC_VDEC_TEST_CK (MTK_PIN_NO(189) | 6)
-
-#define MT8135_PIN_190_SRCLKENAI__FUNC_GPIO190 (MTK_PIN_NO(190) | 0)
-#define MT8135_PIN_190_SRCLKENAI__FUNC_SRCLKENAI (MTK_PIN_NO(190) | 1)
-
-#define MT8135_PIN_191_URXD3__FUNC_GPIO191 (MTK_PIN_NO(191) | 0)
-#define MT8135_PIN_191_URXD3__FUNC_URXD3 (MTK_PIN_NO(191) | 1)
-#define MT8135_PIN_191_URXD3__FUNC_EINT87 (MTK_PIN_NO(191) | 2)
-#define MT8135_PIN_191_URXD3__FUNC_UTXD3 (MTK_PIN_NO(191) | 3)
-#define MT8135_PIN_191_URXD3__FUNC_TS_AUX_ST (MTK_PIN_NO(191) | 5)
-#define MT8135_PIN_191_URXD3__FUNC_PWM4 (MTK_PIN_NO(191) | 6)
-
-#define MT8135_PIN_192_UTXD3__FUNC_GPIO192 (MTK_PIN_NO(192) | 0)
-#define MT8135_PIN_192_UTXD3__FUNC_UTXD3 (MTK_PIN_NO(192) | 1)
-#define MT8135_PIN_192_UTXD3__FUNC_EINT86 (MTK_PIN_NO(192) | 2)
-#define MT8135_PIN_192_UTXD3__FUNC_URXD3 (MTK_PIN_NO(192) | 3)
-#define MT8135_PIN_192_UTXD3__FUNC_TS_AUX_CS_B (MTK_PIN_NO(192) | 5)
-#define MT8135_PIN_192_UTXD3__FUNC_PWM3 (MTK_PIN_NO(192) | 6)
-
-#define MT8135_PIN_193_SDA2__FUNC_GPIO193 (MTK_PIN_NO(193) | 0)
-#define MT8135_PIN_193_SDA2__FUNC_SDA2 (MTK_PIN_NO(193) | 1)
-#define MT8135_PIN_193_SDA2__FUNC_EINT95 (MTK_PIN_NO(193) | 2)
-#define MT8135_PIN_193_SDA2__FUNC_CLKM5 (MTK_PIN_NO(193) | 3)
-#define MT8135_PIN_193_SDA2__FUNC_PWM5 (MTK_PIN_NO(193) | 4)
-#define MT8135_PIN_193_SDA2__FUNC_TS_AUX_PWDB (MTK_PIN_NO(193) | 5)
-
-#define MT8135_PIN_194_SCL2__FUNC_GPIO194 (MTK_PIN_NO(194) | 0)
-#define MT8135_PIN_194_SCL2__FUNC_SCL2 (MTK_PIN_NO(194) | 1)
-#define MT8135_PIN_194_SCL2__FUNC_EINT94 (MTK_PIN_NO(194) | 2)
-#define MT8135_PIN_194_SCL2__FUNC_CLKM4 (MTK_PIN_NO(194) | 3)
-#define MT8135_PIN_194_SCL2__FUNC_PWM4 (MTK_PIN_NO(194) | 4)
-#define MT8135_PIN_194_SCL2__FUNC_TS_AUXADC_TEST_CK (MTK_PIN_NO(194) | 5)
-
-#define MT8135_PIN_195_SDA1__FUNC_GPIO195 (MTK_PIN_NO(195) | 0)
-#define MT8135_PIN_195_SDA1__FUNC_SDA1 (MTK_PIN_NO(195) | 1)
-#define MT8135_PIN_195_SDA1__FUNC_EINT93 (MTK_PIN_NO(195) | 2)
-#define MT8135_PIN_195_SDA1__FUNC_CLKM3 (MTK_PIN_NO(195) | 3)
-#define MT8135_PIN_195_SDA1__FUNC_PWM3 (MTK_PIN_NO(195) | 4)
-#define MT8135_PIN_195_SDA1__FUNC_TS_AUX_SCLK_PWDB (MTK_PIN_NO(195) | 5)
-
-#define MT8135_PIN_196_SCL1__FUNC_GPIO196 (MTK_PIN_NO(196) | 0)
-#define MT8135_PIN_196_SCL1__FUNC_SCL1 (MTK_PIN_NO(196) | 1)
-#define MT8135_PIN_196_SCL1__FUNC_EINT92 (MTK_PIN_NO(196) | 2)
-#define MT8135_PIN_196_SCL1__FUNC_CLKM2 (MTK_PIN_NO(196) | 3)
-#define MT8135_PIN_196_SCL1__FUNC_PWM2 (MTK_PIN_NO(196) | 4)
-#define MT8135_PIN_196_SCL1__FUNC_TS_AUX_DIN (MTK_PIN_NO(196) | 5)
-
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_GPIO197 (MTK_PIN_NO(197) | 0)
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_MSDC3_DAT2 (MTK_PIN_NO(197) | 1)
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_EINT71 (MTK_PIN_NO(197) | 2)
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_SCL6 (MTK_PIN_NO(197) | 3)
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_PWM5 (MTK_PIN_NO(197) | 4)
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_CLKM4 (MTK_PIN_NO(197) | 5)
-#define MT8135_PIN_197_MSDC3_DAT2__FUNC_MFG_TEST_CK_2 (MTK_PIN_NO(197) | 6)
-
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_GPIO198 (MTK_PIN_NO(198) | 0)
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_MSDC3_DAT3 (MTK_PIN_NO(198) | 1)
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_EINT72 (MTK_PIN_NO(198) | 2)
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_SDA6 (MTK_PIN_NO(198) | 3)
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_PWM6 (MTK_PIN_NO(198) | 4)
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_CLKM5 (MTK_PIN_NO(198) | 5)
-#define MT8135_PIN_198_MSDC3_DAT3__FUNC_MFG_TEST_CK_3 (MTK_PIN_NO(198) | 6)
-
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_GPIO199 (MTK_PIN_NO(199) | 0)
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_MSDC3_CMD (MTK_PIN_NO(199) | 1)
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_EINT68 (MTK_PIN_NO(199) | 2)
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_SDA2 (MTK_PIN_NO(199) | 3)
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_PWM2 (MTK_PIN_NO(199) | 4)
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_CLKM1 (MTK_PIN_NO(199) | 5)
-#define MT8135_PIN_199_MSDC3_CMD__FUNC_MFG_TEST_CK_4 (MTK_PIN_NO(199) | 6)
-
-#define MT8135_PIN_200_MSDC3_CLK__FUNC_GPIO200 (MTK_PIN_NO(200) | 0)
-#define MT8135_PIN_200_MSDC3_CLK__FUNC_MSDC3_CLK (MTK_PIN_NO(200) | 1)
-#define MT8135_PIN_200_MSDC3_CLK__FUNC_EINT67 (MTK_PIN_NO(200) | 2)
-#define MT8135_PIN_200_MSDC3_CLK__FUNC_SCL2 (MTK_PIN_NO(200) | 3)
-#define MT8135_PIN_200_MSDC3_CLK__FUNC_PWM1 (MTK_PIN_NO(200) | 4)
-#define MT8135_PIN_200_MSDC3_CLK__FUNC_CLKM0 (MTK_PIN_NO(200) | 5)
-
-#define MT8135_PIN_201_MSDC3_DAT1__FUNC_GPIO201 (MTK_PIN_NO(201) | 0)
-#define MT8135_PIN_201_MSDC3_DAT1__FUNC_MSDC3_DAT1 (MTK_PIN_NO(201) | 1)
-#define MT8135_PIN_201_MSDC3_DAT1__FUNC_EINT70 (MTK_PIN_NO(201) | 2)
-#define MT8135_PIN_201_MSDC3_DAT1__FUNC_SDA3 (MTK_PIN_NO(201) | 3)
-#define MT8135_PIN_201_MSDC3_DAT1__FUNC_PWM4 (MTK_PIN_NO(201) | 4)
-#define MT8135_PIN_201_MSDC3_DAT1__FUNC_CLKM3 (MTK_PIN_NO(201) | 5)
-
-#define MT8135_PIN_202_MSDC3_DAT0__FUNC_GPIO202 (MTK_PIN_NO(202) | 0)
-#define MT8135_PIN_202_MSDC3_DAT0__FUNC_MSDC3_DAT0 (MTK_PIN_NO(202) | 1)
-#define MT8135_PIN_202_MSDC3_DAT0__FUNC_EINT69 (MTK_PIN_NO(202) | 2)
-#define MT8135_PIN_202_MSDC3_DAT0__FUNC_SCL3 (MTK_PIN_NO(202) | 3)
-#define MT8135_PIN_202_MSDC3_DAT0__FUNC_PWM3 (MTK_PIN_NO(202) | 4)
-#define MT8135_PIN_202_MSDC3_DAT0__FUNC_CLKM2 (MTK_PIN_NO(202) | 5)
-
-#endif /* __DTS_MT8135_PINFUNC_H */
diff --git a/arch/arm/boot/dts/nspire-clp.dts b/arch/arm/boot/dts/nspire-clp.dts
deleted file mode 100644
index f52f38c61588..000000000000
--- a/arch/arm/boot/dts/nspire-clp.dts
+++ /dev/null
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/boot/nspire-clp.dts
- *
- *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
- */
-/dts-v1/;
-
-/include/ "nspire-classic.dtsi"
-
-&keypad {
-	linux,keymap = <
-	0x0000001c 	0x0001001c 	0x00020039
-	0x0004002c 	0x00050034 	0x00060015
-	0x0007000b 	0x0008002d 	0x01000033
-	0x0101004e 	0x01020011 	0x01030004
-	0x0104002f 	0x01050003 	0x01060016
-	0x01070002 	0x01080014 	0x02000062
-	0x0201000c 	0x0202001f 	0x02030007
-	0x02040013 	0x02050006 	0x02060010
-	0x02070005 	0x02080019 	0x03000027
-	0x03010037 	0x03020018 	0x0303000a
-	0x03040031 	0x03050009 	0x03060032
-	0x03070008 	0x03080026 	0x04000028
-	0x04010035 	0x04020025 	0x04040024
-	0x04060017 	0x04080023 	0x05000028
-	0x05020022 	0x0503001b 	0x05040021
-	0x0505001a 	0x05060012 	0x0507006f
-	0x05080020 	0x0509002a 	0x0601001c
-	0x0602002e 	0x06030068 	0x06040030
-	0x0605006d 	0x0606001e 	0x06070001
-	0x0608002b 	0x0609000f 	0x07000067
-	0x0702006a 	0x0704006c 	0x07060069
-	0x0707000e 	0x0708001d 	0x070a000d
-	>;
-};
-
-/ {
-	model = "TI-NSPIRE Clickpad";
-	compatible = "ti,nspire-clp";
-};
diff --git a/arch/arm/boot/dts/nspire-cx.dts b/arch/arm/boot/dts/nspire-cx.dts
deleted file mode 100644
index 0c16b04e2744..000000000000
--- a/arch/arm/boot/dts/nspire-cx.dts
+++ /dev/null
@@ -1,125 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/boot/nspire-cx.dts
- *
- *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
- */
-/dts-v1/;
-
-/include/ "nspire.dtsi"
-
-&lcd {
-	port {
-		clcd_pads: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-&fast_timer {
-	/* compatible = "arm,sp804", "arm,primecell"; */
-};
-
-&uart {
-	compatible = "arm,pl011", "arm,primecell";
-
-	clocks = <&uart_clk>, <&apb_pclk>;
-	clock-names = "uart_clk", "apb_pclk";
-};
-
-&timer0 {
-	compatible = "arm,sp804", "arm,primecell";
-};
-
-&timer1 {
-	compatible = "arm,sp804", "arm,primecell";
-};
-
-&base_clk {
-	compatible = "lsi,nspire-cx-clock";
-};
-
-&ahb_clk {
-	compatible = "lsi,nspire-cx-ahb-divider";
-};
-
-&keypad {
-	linux,keymap = <
-	0x0000001c 	0x0001001c 	0x00040039
-	0x0005002c 	0x00060015 	0x0007000b
-	0x0008000f 	0x0100002d 	0x01010011
-	0x0102002f 	0x01030004 	0x01040016
-	0x01050014 	0x0106001f 	0x01070002
-	0x010a006a 	0x02000013 	0x02010010
-	0x02020019 	0x02030007 	0x02040018
-	0x02050031 	0x02060032 	0x02070005
-	0x02080028 	0x0209006c 	0x03000026
-	0x03010025 	0x03020024 	0x0303000a
-	0x03040017 	0x03050023 	0x03060022
-	0x03070008 	0x03080035 	0x03090069
-	0x04000021 	0x04010012 	0x04020020
-	0x0404002e 	0x04050030 	0x0406001e
-	0x0407000d 	0x04080037 	0x04090067
-	0x05010038 	0x0502000c 	0x0503001b
-	0x05040034 	0x0505001a 	0x05060006
-	0x05080027 	0x0509000e 	0x050a006f
-	0x0600002b 	0x0602004e 	0x06030068
-	0x06040003 	0x0605006d 	0x06060009
-	0x06070001 	0x0609000f 	0x0708002a
-	0x0709001d 	0x070a0033 	>;
-};
-
-&vbus_reg {
-	gpio = <&gpio 2 0>;
-};
-
-/ {
-	model = "TI-NSPIRE CX";
-	compatible = "ti,nspire-cx";
-
-	memory {
-		device_type = "memory";
-		reg = <0x10000000 0x4000000>; /* 64 MB */
-	};
-
-	uart_clk: uart_clk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <12000000>;
-	};
-
-	ahb {
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		intc: interrupt-controller@DC000000 {
-			compatible = "arm,pl190-vic";
-			interrupt-controller;
-			reg = <0xDC000000 0x1000>;
-			#interrupt-cells = <1>;
-		};
-
-		apb@90000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			i2c@90050000 {
-				compatible = "snps,designware-i2c";
-				reg = <0x90050000 0x1000>;
-				interrupts = <20>;
-			};
-		};
-	};
-
-	panel {
-		compatible = "ti,nspire-cx-lcd-panel";
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&clcd_pads>;
-			};
-		};
-	};
-	chosen {
-		bootargs = "debug earlyprintk console=tty0 console=ttyAMA0,115200n8 root=/dev/ram0";
-	};
-};
diff --git a/arch/arm/boot/dts/nspire-tp.dts b/arch/arm/boot/dts/nspire-tp.dts
deleted file mode 100644
index f7d0faacd4cc..000000000000
--- a/arch/arm/boot/dts/nspire-tp.dts
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/boot/nspire-tp.dts
- *
- *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
- */
-/dts-v1/;
-
-/include/ "nspire-classic.dtsi"
-
-&keypad {
-	linux,keymap = <
-	0x0000001c 	0x0001001c 	0x00040039
-	0x0005002c 	0x00060015 	0x0007000b
-	0x0008000f 	0x0100002d 	0x01010011
-	0x0102002f 	0x01030004 	0x01040016
-	0x01050014 	0x0106001f 	0x01070002
-	0x010a006a 	0x02000013 	0x02010010
-	0x02020019 	0x02030007 	0x02040018
-	0x02050031 	0x02060032 	0x02070005
-	0x02080028 	0x0209006c 	0x03000026
-	0x03010025 	0x03020024 	0x0303000a
-	0x03040017 	0x03050023 	0x03060022
-	0x03070008 	0x03080035 	0x03090069
-	0x04000021 	0x04010012 	0x04020020
-	0x0404002e 	0x04050030 	0x0406001e
-	0x0407000d 	0x04080037 	0x04090067
-	0x05010038 	0x0502000c 	0x0503001b
-	0x05040034 	0x0505001a 	0x05060006
-	0x05080027 	0x0509000e 	0x050a006f
-	0x0600002b 	0x0602004e 	0x06030068
-	0x06040003 	0x0605006d 	0x06060009
-	0x06070001 	0x0609000f 	0x0708002a
-	0x0709001d 	0x070a0033 	>;
-};
-
-/ {
-	model = "TI-NSPIRE Touchpad";
-	compatible = "ti,nspire-tp";
-};
diff --git a/arch/arm/boot/dts/nspire/Makefile b/arch/arm/boot/dts/nspire/Makefile
new file mode 100644
index 000000000000..82a2515bdd46
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NSPIRE) += \
+	nspire-cx.dtb \
+	nspire-tp.dtb \
+	nspire-clp.dtb
diff --git a/arch/arm/boot/dts/nspire-classic.dtsi b/arch/arm/boot/dts/nspire/nspire-classic.dtsi
index 41744cc2bc72..a6e9cbf51524 100644
--- a/arch/arm/boot/dts/nspire-classic.dtsi
+++ b/arch/arm/boot/dts/nspire/nspire-classic.dtsi
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- *  linux/arch/arm/boot/nspire-classic.dts
- *
  *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
  */
 
@@ -17,7 +15,7 @@
 
 &fast_timer {
 	/* compatible = "lsi,zevio-timer"; */
-	reg = <0x90010000 0x1000>, <0x900A0010 0x8>;
+	reg = <0x90010000 0x1000>, <0x900a0010 0x8>;
 };
 
 &uart {
@@ -30,12 +28,12 @@
 
 &timer0 {
 	/* compatible = "lsi,zevio-timer"; */
-	reg = <0x900C0000 0x1000>, <0x900A0018 0x8>;
+	reg = <0x900c0000 0x1000>, <0x900a0018 0x8>;
 };
 
 &timer1 {
 	compatible = "lsi,zevio-timer";
-	reg = <0x900D0000 0x1000>, <0x900A0020 0x8>;
+	reg = <0x900d0000 0x1000>, <0x900a0020 0x8>;
 };
 
 &keypad {
@@ -66,10 +64,10 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		intc: interrupt-controller@DC000000 {
+		intc: interrupt-controller@dc000000 {
 			compatible = "lsi,zevio-intc";
 			interrupt-controller;
-			reg = <0xDC000000 0x1000>;
+			reg = <0xdc000000 0x1000>;
 			#interrupt-cells = <1>;
 		};
 	};
diff --git a/arch/arm/boot/dts/nspire/nspire-clp.dts b/arch/arm/boot/dts/nspire/nspire-clp.dts
new file mode 100644
index 000000000000..c5773f770fd4
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/nspire-clp.dts
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+/include/ "nspire-classic.dtsi"
+
+&keypad {
+	linux,keymap = <
+		MATRIX_KEY(0,  0, 0x1c)
+		MATRIX_KEY(0,  1, 0x1c)
+		MATRIX_KEY(0,  2, 0x39)
+		MATRIX_KEY(0,  4, 0x2c)
+		MATRIX_KEY(0,  5, 0x34)
+		MATRIX_KEY(0,  6, 0x15)
+		MATRIX_KEY(0,  7, 0x0b)
+		MATRIX_KEY(0,  8, 0x2d)
+		MATRIX_KEY(1,  0, 0x33)
+		MATRIX_KEY(1,  1, 0x4e)
+		MATRIX_KEY(1,  2, 0x11)
+		MATRIX_KEY(1,  3, 0x04)
+		MATRIX_KEY(1,  4, 0x2f)
+		MATRIX_KEY(1,  5, 0x03)
+		MATRIX_KEY(1,  6, 0x16)
+		MATRIX_KEY(1,  7, 0x02)
+		MATRIX_KEY(1,  8, 0x14)
+		MATRIX_KEY(2,  0, 0x62)
+		MATRIX_KEY(2,  1, 0x0c)
+		MATRIX_KEY(2,  2, 0x1f)
+		MATRIX_KEY(2,  3, 0x07)
+		MATRIX_KEY(2,  4, 0x13)
+		MATRIX_KEY(2,  5, 0x06)
+		MATRIX_KEY(2,  6, 0x10)
+		MATRIX_KEY(2,  7, 0x05)
+		MATRIX_KEY(2,  8, 0x19)
+		MATRIX_KEY(3,  0, 0x27)
+		MATRIX_KEY(3,  1, 0x37)
+		MATRIX_KEY(3,  2, 0x18)
+		MATRIX_KEY(3,  3, 0x0a)
+		MATRIX_KEY(3,  4, 0x31)
+		MATRIX_KEY(3,  5, 0x09)
+		MATRIX_KEY(3,  6, 0x32)
+		MATRIX_KEY(3,  7, 0x08)
+		MATRIX_KEY(3,  8, 0x26)
+		MATRIX_KEY(4,  0, 0x28)
+		MATRIX_KEY(4,  1, 0x35)
+		MATRIX_KEY(4,  2, 0x25)
+		MATRIX_KEY(4,  4, 0x24)
+		MATRIX_KEY(4,  6, 0x17)
+		MATRIX_KEY(4,  8, 0x23)
+		MATRIX_KEY(5,  0, 0x28)
+		MATRIX_KEY(5,  2, 0x22)
+		MATRIX_KEY(5,  3, 0x1b)
+		MATRIX_KEY(5,  4, 0x21)
+		MATRIX_KEY(5,  5, 0x1a)
+		MATRIX_KEY(5,  6, 0x12)
+		MATRIX_KEY(5,  7, 0x6f)
+		MATRIX_KEY(5,  8, 0x20)
+		MATRIX_KEY(5,  9, 0x2a)
+		MATRIX_KEY(6,  1, 0x1c)
+		MATRIX_KEY(6,  2, 0x2e)
+		MATRIX_KEY(6,  3, 0x68)
+		MATRIX_KEY(6,  4, 0x30)
+		MATRIX_KEY(6,  5, 0x6d)
+		MATRIX_KEY(6,  6, 0x1e)
+		MATRIX_KEY(6,  7, 0x01)
+		MATRIX_KEY(6,  8, 0x2b)
+		MATRIX_KEY(6,  9, 0x0f)
+		MATRIX_KEY(7,  0, 0x67)
+		MATRIX_KEY(7,  2, 0x6a)
+		MATRIX_KEY(7,  4, 0x6c)
+		MATRIX_KEY(7,  6, 0x69)
+		MATRIX_KEY(7,  7, 0x0e)
+		MATRIX_KEY(7,  8, 0x1d)
+		MATRIX_KEY(7, 10, 0x0d)
+	>;
+};
+
+/ {
+	model = "TI-NSPIRE Clickpad";
+	compatible = "ti,nspire-clp";
+};
diff --git a/arch/arm/boot/dts/nspire/nspire-cx.dts b/arch/arm/boot/dts/nspire/nspire-cx.dts
new file mode 100644
index 000000000000..29f0181e5b38
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/nspire-cx.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+/include/ "nspire.dtsi"
+
+&lcd {
+	port {
+		clcd_pads: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&fast_timer {
+	/* compatible = "arm,sp804", "arm,primecell"; */
+};
+
+&uart {
+	compatible = "arm,pl011", "arm,primecell";
+
+	clocks = <&uart_clk>, <&apb_pclk>;
+	clock-names = "uartclk", "apb_pclk";
+};
+
+&timer0 {
+	compatible = "arm,sp804", "arm,primecell";
+};
+
+&timer1 {
+	compatible = "arm,sp804", "arm,primecell";
+};
+
+&base_clk {
+	compatible = "lsi,nspire-cx-clock";
+};
+
+&ahb_clk {
+	compatible = "lsi,nspire-cx-ahb-divider";
+};
+
+&keypad {
+	linux,keymap = <
+		MATRIX_KEY(0,  0, 0x1c)
+		MATRIX_KEY(0,  1, 0x1c)
+		MATRIX_KEY(0,  4, 0x39)
+		MATRIX_KEY(0,  5, 0x2c)
+		MATRIX_KEY(0,  6, 0x15)
+		MATRIX_KEY(0,  7, 0x0b)
+		MATRIX_KEY(0,  8, 0x0f)
+		MATRIX_KEY(1,  0, 0x2d)
+		MATRIX_KEY(1,  1, 0x11)
+		MATRIX_KEY(1,  2, 0x2f)
+		MATRIX_KEY(1,  3, 0x04)
+		MATRIX_KEY(1,  4, 0x16)
+		MATRIX_KEY(1,  5, 0x14)
+		MATRIX_KEY(1,  6, 0x1f)
+		MATRIX_KEY(1,  7, 0x02)
+		MATRIX_KEY(1, 10, 0x6a)
+		MATRIX_KEY(2,  0, 0x13)
+		MATRIX_KEY(2,  1, 0x10)
+		MATRIX_KEY(2,  2, 0x19)
+		MATRIX_KEY(2,  3, 0x07)
+		MATRIX_KEY(2,  4, 0x18)
+		MATRIX_KEY(2,  5, 0x31)
+		MATRIX_KEY(2,  6, 0x32)
+		MATRIX_KEY(2,  7, 0x05)
+		MATRIX_KEY(2,  8, 0x28)
+		MATRIX_KEY(2,  9, 0x6c)
+		MATRIX_KEY(3,  0, 0x26)
+		MATRIX_KEY(3,  1, 0x25)
+		MATRIX_KEY(3,  2, 0x24)
+		MATRIX_KEY(3,  3, 0x0a)
+		MATRIX_KEY(3,  4, 0x17)
+		MATRIX_KEY(3,  5, 0x23)
+		MATRIX_KEY(3,  6, 0x22)
+		MATRIX_KEY(3,  7, 0x08)
+		MATRIX_KEY(3,  8, 0x35)
+		MATRIX_KEY(3,  9, 0x69)
+		MATRIX_KEY(4,  0, 0x21)
+		MATRIX_KEY(4,  1, 0x12)
+		MATRIX_KEY(4,  2, 0x20)
+		MATRIX_KEY(4,  4, 0x2e)
+		MATRIX_KEY(4,  5, 0x30)
+		MATRIX_KEY(4,  6, 0x1e)
+		MATRIX_KEY(4,  7, 0x0d)
+		MATRIX_KEY(4,  8, 0x37)
+		MATRIX_KEY(4,  9, 0x67)
+		MATRIX_KEY(5,  1, 0x38)
+		MATRIX_KEY(5,  2, 0x0c)
+		MATRIX_KEY(5,  3, 0x1b)
+		MATRIX_KEY(5,  4, 0x34)
+		MATRIX_KEY(5,  5, 0x1a)
+		MATRIX_KEY(5,  6, 0x06)
+		MATRIX_KEY(5,  8, 0x27)
+		MATRIX_KEY(5,  9, 0x0e)
+		MATRIX_KEY(5, 10, 0x6f)
+		MATRIX_KEY(6,  0, 0x2b)
+		MATRIX_KEY(6,  2, 0x4e)
+		MATRIX_KEY(6,  3, 0x68)
+		MATRIX_KEY(6,  4, 0x03)
+		MATRIX_KEY(6,  5, 0x6d)
+		MATRIX_KEY(6,  6, 0x09)
+		MATRIX_KEY(6,  7, 0x01)
+		MATRIX_KEY(6,  9, 0x0f)
+		MATRIX_KEY(7,  8, 0x2a)
+		MATRIX_KEY(7,  9, 0x1d)
+		MATRIX_KEY(7, 10, 0x33)
+	>;
+};
+
+&vbus_reg {
+	gpio = <&gpio 2 0>;
+};
+
+/ {
+	model = "TI-NSPIRE CX";
+	compatible = "ti,nspire-cx";
+
+	memory {
+		device_type = "memory";
+		reg = <0x10000000 0x4000000>; /* 64 MB */
+	};
+
+	uart_clk: uart_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		intc: interrupt-controller@dc000000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xdc000000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		apb@90000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			i2c@90050000 {
+				compatible = "snps,designware-i2c";
+				reg = <0x90050000 0x1000>;
+				interrupts = <20>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "ti,nspire-cx-lcd-panel";
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&clcd_pads>;
+			};
+		};
+	};
+	chosen {
+		bootargs = "debug earlyprintk console=tty0 console=ttyAMA0,115200n8 root=/dev/ram0";
+	};
+};
diff --git a/arch/arm/boot/dts/nspire/nspire-tp.dts b/arch/arm/boot/dts/nspire/nspire-tp.dts
new file mode 100644
index 000000000000..3f0107f1c2c7
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/nspire-tp.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+/include/ "nspire-classic.dtsi"
+
+&keypad {
+	linux,keymap = <
+		MATRIX_KEY(0,  0, 0x1c)
+		MATRIX_KEY(0,  1, 0x1c)
+		MATRIX_KEY(0,  4, 0x39)
+		MATRIX_KEY(0,  5, 0x2c)
+		MATRIX_KEY(0,  6, 0x15)
+		MATRIX_KEY(0,  7, 0x0b)
+		MATRIX_KEY(0,  8, 0x0f)
+		MATRIX_KEY(1,  0, 0x2d)
+		MATRIX_KEY(1,  1, 0x11)
+		MATRIX_KEY(1,  2, 0x2f)
+		MATRIX_KEY(1,  3, 0x04)
+		MATRIX_KEY(1,  4, 0x16)
+		MATRIX_KEY(1,  5, 0x14)
+		MATRIX_KEY(1,  6, 0x1f)
+		MATRIX_KEY(1,  7, 0x02)
+		MATRIX_KEY(1, 10, 0x6a)
+		MATRIX_KEY(2,  0, 0x13)
+		MATRIX_KEY(2,  1, 0x10)
+		MATRIX_KEY(2,  2, 0x19)
+		MATRIX_KEY(2,  3, 0x07)
+		MATRIX_KEY(2,  4, 0x18)
+		MATRIX_KEY(2,  5, 0x31)
+		MATRIX_KEY(2,  6, 0x32)
+		MATRIX_KEY(2,  7, 0x05)
+		MATRIX_KEY(2,  8, 0x28)
+		MATRIX_KEY(2,  9, 0x6c)
+		MATRIX_KEY(3,  0, 0x26)
+		MATRIX_KEY(3,  1, 0x25)
+		MATRIX_KEY(3,  2, 0x24)
+		MATRIX_KEY(3,  3, 0x0a)
+		MATRIX_KEY(3,  4, 0x17)
+		MATRIX_KEY(3,  5, 0x23)
+		MATRIX_KEY(3,  6, 0x22)
+		MATRIX_KEY(3,  7, 0x08)
+		MATRIX_KEY(3,  8, 0x35)
+		MATRIX_KEY(3,  9, 0x69)
+		MATRIX_KEY(4,  0, 0x21)
+		MATRIX_KEY(4,  1, 0x12)
+		MATRIX_KEY(4,  2, 0x20)
+		MATRIX_KEY(4,  4, 0x2e)
+		MATRIX_KEY(4,  5, 0x30)
+		MATRIX_KEY(4,  6, 0x1e)
+		MATRIX_KEY(4,  7, 0x0d)
+		MATRIX_KEY(4,  8, 0x37)
+		MATRIX_KEY(4,  9, 0x67)
+		MATRIX_KEY(5,  1, 0x38)
+		MATRIX_KEY(5,  2, 0x0c)
+		MATRIX_KEY(5,  3, 0x1b)
+		MATRIX_KEY(5,  4, 0x34)
+		MATRIX_KEY(5,  5, 0x1a)
+		MATRIX_KEY(5,  6, 0x06)
+		MATRIX_KEY(5,  8, 0x27)
+		MATRIX_KEY(5,  9, 0x0e)
+		MATRIX_KEY(5, 10, 0x6f)
+		MATRIX_KEY(6,  0, 0x2b)
+		MATRIX_KEY(6,  2, 0x4e)
+		MATRIX_KEY(6,  3, 0x68)
+		MATRIX_KEY(6,  4, 0x03)
+		MATRIX_KEY(6,  5, 0x6d)
+		MATRIX_KEY(6,  6, 0x09)
+		MATRIX_KEY(6,  7, 0x01)
+		MATRIX_KEY(6,  9, 0x0f)
+		MATRIX_KEY(7,  8, 0x2a)
+		MATRIX_KEY(7,  9, 0x1d)
+		MATRIX_KEY(7, 10, 0x33)
+	>;
+};
+
+/ {
+	model = "TI-NSPIRE Touchpad";
+	compatible = "ti,nspire-tp";
+};
diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire/nspire.dtsi
index d9a0fd7524dc..d56fef7250db 100644
--- a/arch/arm/boot/dts/nspire.dtsi
+++ b/arch/arm/boot/dts/nspire/nspire.dtsi
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- *  linux/arch/arm/boot/nspire.dtsi
- *
  *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
  */
 
@@ -11,8 +9,13 @@
 	interrupt-parent = <&intc>;
 
 	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
 		cpu@0 {
 			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
@@ -20,9 +23,16 @@
 		reg = <0x00000000 0x80000>;
 	};
 
-	sram: sram@A4000000 {
-		device = "memory";
-		reg = <0xA4000000 0x20000>;
+	sram: sram@a4000000 {
+		compatible = "mmio-sram";
+		reg = <0xa4000000 0x20000>; /* 128k */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xa4000000 0x20000>;
+
+		sram@0 {
+			reg = <0x0 0x20000>;
+		};
 	};
 
 	timer_clk: timer_clk {
@@ -33,12 +43,12 @@
 
 	base_clk: base_clk {
 		#clock-cells = <0>;
-		reg = <0x900B0024 0x4>;
+		reg = <0x900b0024 0x4>;
 	};
 
 	ahb_clk: ahb_clk {
 		#clock-cells = <0>;
-		reg = <0x900B0024 0x4>;
+		reg = <0x900b0024 0x4>;
 		clocks = <&base_clk>;
 	};
 
@@ -59,7 +69,6 @@
 		compatible = "regulator-fixed";
 
 		regulator-name = "USB VBUS output";
-		regulator-type = "voltage";
 
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -71,28 +80,28 @@
 		#size-cells = <1>;
 		ranges;
 
-		spi: spi@A9000000 {
-			reg = <0xA9000000 0x1000>;
+		spi: spi@a9000000 {
+			reg = <0xa9000000 0x1000>;
 		};
 
-		usb0: usb@B0000000 {
+		usb0: usb@b0000000 {
 			compatible = "lsi,zevio-usb";
-			reg = <0xB0000000 0x1000>;
+			reg = <0xb0000000 0x1000>;
 			interrupts = <8>;
 
 			usb-phy = <&usb_phy>;
 			vbus-supply = <&vbus_reg>;
 		};
 
-		usb1: usb@B4000000 {
-			reg = <0xB4000000 0x1000>;
+		usb1: usb@b4000000 {
+			reg = <0xb4000000 0x1000>;
 			interrupts = <9>;
 			status = "disabled";
 		};
 
-		lcd: lcd@C0000000 {
+		lcd: lcd@c0000000 {
 			compatible = "arm,pl111", "arm,primecell";
-			reg = <0xC0000000 0x1000>;
+			reg = <0xc0000000 0x1000>;
 			interrupts = <21>;
 
 			/*
@@ -105,17 +114,17 @@
 			clock-names = "clcdclk", "apb_pclk";
 		};
 
-		adc: adc@C4000000 {
-			reg = <0xC4000000 0x1000>;
+		adc: adc@c4000000 {
+			reg = <0xc4000000 0x1000>;
 			interrupts = <11>;
 		};
 
-		tdes: crypto@C8010000 {
-			reg = <0xC8010000 0x1000>;
+		tdes: crypto@c8010000 {
+			reg = <0xc8010000 0x1000>;
 		};
 
-		sha256: crypto@CC000000 {
-			reg = <0xCC000000 0x1000>;
+		sha256: crypto@cc000000 {
+			reg = <0xcc000000 0x1000>;
 		};
 
 		apb@90000000 {
@@ -143,21 +152,25 @@
 				interrupts = <1>;
 			};
 
-			timer0: timer@900C0000 {
-				reg = <0x900C0000 0x1000>;
-
-				clocks = <&timer_clk>;
+			timer0: timer@900c0000 {
+				reg = <0x900c0000 0x1000>;
+				clocks = <&timer_clk>, <&timer_clk>,
+					 <&timer_clk>;
+				clock-names = "timer0clk", "timer1clk",
+					      "apb_pclk";
 			};
 
-			timer1: timer@900D0000 {
-				reg = <0x900D0000 0x1000>;
+			timer1: timer@900d0000 {
+				reg = <0x900d0000 0x1000>;
 				interrupts = <19>;
-
-				clocks = <&timer_clk>;
+				clocks = <&timer_clk>, <&timer_clk>,
+					 <&timer_clk>;
+				clock-names = "timer0clk", "timer1clk",
+					      "apb_pclk";
 			};
 
 			watchdog: watchdog@90060000 {
-				compatible = "arm,amba-primecell";
+				compatible = "arm,primecell";
 				reg = <0x90060000 0x1000>;
 				interrupts = <3>;
 			};
@@ -167,18 +180,25 @@
 				interrupts = <4>;
 			};
 
-			misc: misc@900A0000 {
-				reg = <0x900A0000 0x1000>;
+			misc: misc@900a0000 {
+				compatible = "ti,nspire-misc", "syscon", "simple-mfd";
+				reg = <0x900a0000 0x1000>;
+
+				reboot {
+					compatible = "syscon-reboot";
+					offset = <0x08>;
+					value = <0x02>;
+				};
 			};
 
-			pwr: pwr@900B0000 {
-				reg = <0x900B0000 0x1000>;
+			pwr: pwr@900b0000 {
+				reg = <0x900b0000 0x1000>;
 				interrupts = <15>;
 			};
 
-			keypad: input@900E0000 {
+			keypad: input@900e0000 {
 				compatible = "ti,nspire-keypad";
-				reg = <0x900E0000 0x1000>;
+				reg = <0x900e0000 0x1000>;
 				interrupts = <16>;
 
 				scan-interval = <1000>;
@@ -187,8 +207,8 @@
 				clocks = <&apb_pclk>;
 			};
 
-			contrast: contrast@900F0000 {
-				reg = <0x900F0000 0x1000>;
+			contrast: contrast@900f0000 {
+				reg = <0x900f0000 0x1000>;
 			};
 
 			led: led@90110000 {
diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
deleted file mode 100644
index d2d0761295a4..000000000000
--- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
+++ /dev/null
@@ -1,187 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
-// Copyright 2018 Google, Inc.
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&gic>;
-
-	/* external reference clock */
-	clk_refclk: clk_refclk {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-		clock-output-names = "refclk";
-	};
-
-	/* external reference clock for cpu. float in normal operation */
-	clk_sysbypck: clk_sysbypck {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <800000000>;
-		clock-output-names = "sysbypck";
-	};
-
-	/* external reference clock for MC. float in normal operation */
-	clk_mcbypck: clk_mcbypck {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <800000000>;
-		clock-output-names = "mcbypck";
-	};
-
-	 /* external clock signal rg1refck, supplied by the phy */
-	clk_rg1refck: clk_rg1refck {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <125000000>;
-		clock-output-names = "clk_rg1refck";
-	};
-
-	 /* external clock signal rg2refck, supplied by the phy */
-	clk_rg2refck: clk_rg2refck {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <125000000>;
-		clock-output-names = "clk_rg2refck";
-	};
-
-	clk_xin: clk_xin {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <50000000>;
-		clock-output-names = "clk_xin";
-	};
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		interrupt-parent = <&gic>;
-		ranges = <0x0 0xf0000000 0x00900000>;
-
-		gcr: gcr@800000 {
-			compatible = "nuvoton,npcm750-gcr", "syscon",
-				"simple-mfd";
-			reg = <0x800000 0x1000>;
-		};
-
-		scu: scu@3fe000 {
-			compatible = "arm,cortex-a9-scu";
-			reg = <0x3fe000 0x1000>;
-		};
-
-		l2: cache-controller@3fc000 {
-			compatible = "arm,pl310-cache";
-			reg = <0x3fc000 0x1000>;
-			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-			cache-unified;
-			cache-level = <2>;
-			clocks = <&clk 10>;
-			arm,shared-override;
-		};
-
-		gic: interrupt-controller@3ff000 {
-			compatible = "arm,cortex-a9-gic";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x3ff000 0x1000>,
-				<0x3fe100 0x100>;
-		};
-	};
-
-	ahb {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		interrupt-parent = <&gic>;
-		ranges;
-
-		clk: clock-controller@f0801000 {
-			compatible = "nuvoton,npcm750-clk", "syscon";
-			#clock-cells = <1>;
-			clock-controller;
-			reg = <0xf0801000 0x1000>;
-			clock-names = "refclk", "sysbypck", "mcbypck";
-			clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>;
-		};
-
-		apb {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			interrupt-parent = <&gic>;
-			ranges = <0x0 0xf0000000 0x00300000>;
-
-			timer0: timer@8000 {
-				compatible = "nuvoton,npcm750-timer";
-				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x8000 0x50>;
-				clocks = <&clk 5>;
-			};
-
-			watchdog0: watchdog@801C {
-				compatible = "nuvoton,npcm750-wdt";
-				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x801C 0x4>;
-				status = "disabled";
-				clocks = <&clk 5>;
-			};
-
-			watchdog1: watchdog@901C {
-				compatible = "nuvoton,npcm750-wdt";
-				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x901C 0x4>;
-				status = "disabled";
-				clocks = <&clk 5>;
-			};
-
-			watchdog2: watchdog@a01C {
-				compatible = "nuvoton,npcm750-wdt";
-				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xa01C 0x4>;
-				status = "disabled";
-				clocks = <&clk 5>;
-			};
-
-			serial0: serial@1000 {
-				compatible = "nuvoton,npcm750-uart";
-				reg = <0x1000 0x1000>;
-				clocks = <&clk 6>;
-				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-				reg-shift = <2>;
-				status = "disabled";
-			};
-
-			serial1: serial@2000 {
-				compatible = "nuvoton,npcm750-uart";
-				reg = <0x2000 0x1000>;
-				clocks = <&clk 6>;
-				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-				reg-shift = <2>;
-				status = "disabled";
-			};
-
-			serial2: serial@3000 {
-				compatible = "nuvoton,npcm750-uart";
-				reg = <0x3000 0x1000>;
-				clocks = <&clk 6>;
-				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
-				reg-shift = <2>;
-				status = "disabled";
-			};
-
-			serial3: serial@4000 {
-				compatible = "nuvoton,npcm750-uart";
-				reg = <0x4000 0x1000>;
-				clocks = <&clk 6>;
-				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
-				reg-shift = <2>;
-				status = "disabled";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
deleted file mode 100644
index 15f744f1beea..000000000000
--- a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
+++ /dev/null
@@ -1,39 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
-// Copyright 2018 Google, Inc.
-
-/dts-v1/;
-#include "nuvoton-npcm750.dtsi"
-
-/ {
-	model = "Nuvoton npcm750 Development Board (Device Tree)";
-	compatible = "nuvoton,npcm750";
-
-	chosen {
-		stdout-path = &serial3;
-	};
-
-	memory {
-		reg = <0 0x40000000>;
-	};
-};
-
-&watchdog1 {
-	status = "okay";
-};
-
-&serial0 {
-	status = "okay";
-};
-
-&serial1 {
-	status = "okay";
-};
-
-&serial2 {
-	status = "okay";
-};
-
-&serial3 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/nuvoton/Makefile b/arch/arm/boot/dts/nuvoton/Makefile
new file mode 100644
index 000000000000..89c157dad312
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NPCM7XX) += \
+	nuvoton-npcm730-gsj.dtb \
+	nuvoton-npcm730-gbs.dtb \
+	nuvoton-npcm730-kudo.dtb \
+	nuvoton-npcm750-evb.dtb \
+	nuvoton-npcm750-runbmc-olympus.dtb
+dtb-$(CONFIG_ARCH_WPCM450) += \
+	nuvoton-wpcm450-supermicro-x9sci-ln4f.dtb
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
new file mode 100644
index 000000000000..868454ae6bde
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
@@ -0,0 +1,1132 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
+// Copyright 2018 Google, Inc.
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/nuvoton,npcm7xx-clock.h>
+#include <dt-bindings/reset/nuvoton,npcm7xx-reset.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	/* external reference clock */
+	clk_refclk: clk_refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "refclk";
+	};
+
+	/* external reference clock for cpu. float in normal operation */
+	clk_sysbypck: clk_sysbypck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <800000000>;
+		clock-output-names = "sysbypck";
+	};
+
+	/* external reference clock for MC. float in normal operation */
+	clk_mcbypck: clk_mcbypck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <800000000>;
+		clock-output-names = "mcbypck";
+	};
+
+	 /* external clock signal rg1refck, supplied by the phy */
+	clk_rg1refck: clk_rg1refck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "clk_rg1refck";
+	};
+
+	 /* external clock signal rg2refck, supplied by the phy */
+	clk_rg2refck: clk_rg2refck {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "clk_rg2refck";
+	};
+
+	clk_xin: clk_xin {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "clk_xin";
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges = <0x0 0xf0000000 0x00900000>;
+
+		scu: scu@3fe000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0x3fe000 0x1000>;
+		};
+
+		l2: cache-controller@3fc000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x3fc000 0x1000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			cache-unified;
+			cache-level = <2>;
+			clocks = <&clk NPCM7XX_CLK_AXI>;
+			arm,shared-override;
+		};
+
+		gic: interrupt-controller@3ff000 {
+			compatible = "arm,cortex-a9-gic";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x3ff000 0x1000>,
+				<0x3fe100 0x100>;
+		};
+
+		gcr: gcr@800000 {
+			compatible = "nuvoton,npcm750-gcr", "syscon", "simple-mfd";
+			reg = <0x800000 0x1000>;
+		};
+
+		rst: rst@801000 {
+			compatible = "nuvoton,npcm750-rst", "syscon", "simple-mfd";
+			reg = <0x801000 0x6C>;
+		};
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		rstc: rstc@f0801000 {
+			compatible = "nuvoton,npcm750-reset";
+			reg = <0xf0801000 0x70>;
+			#reset-cells = <2>;
+			nuvoton,sysgcr = <&gcr>;
+		};
+
+		clk: clock-controller@f0801000 {
+			compatible = "nuvoton,npcm750-clk", "syscon";
+			#clock-cells = <1>;
+			clock-controller;
+			reg = <0xf0801000 0x1000>;
+			clock-names = "refclk", "sysbypck", "mcbypck";
+			clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>;
+		};
+
+		gmac0: eth@f0802000 {
+			device_type = "network";
+			compatible = "snps,dwmac";
+			reg = <0xf0802000 0x2000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			ethernet = <0>;
+			clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "stmmaceth", "clk_gmac";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rg1_pins
+					&rg1mdio_pins>;
+			status = "disabled";
+		};
+
+		ehci1: usb@f0806000 {
+			compatible = "nuvoton,npcm750-ehci";
+			reg = <0xf0806000 0x1000>;
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		fiu0: spi@fb000000 {
+			compatible = "nuvoton,npcm750-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfb000000 0x1000>;
+			reg-names = "control", "memory";
+			clocks = <&clk NPCM7XX_CLK_SPI0>;
+			clock-names = "clk_spi0";
+			status = "disabled";
+		};
+
+		fiu3: spi@c0000000 {
+			compatible = "nuvoton,npcm750-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xc0000000 0x1000>;
+			reg-names = "control", "memory";
+			clocks = <&clk NPCM7XX_CLK_SPI3>;
+			clock-names = "clk_spi3";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi3_pins>;
+			status = "disabled";
+		};
+
+		fiux: spi@fb001000 {
+			compatible = "nuvoton,npcm750-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfb001000 0x1000>;
+			reg-names = "control", "memory";
+			clocks = <&clk NPCM7XX_CLK_SPIX>;
+			clock-names = "clk_spix";
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			interrupt-parent = <&gic>;
+			ranges = <0x0 0xf0000000 0x00300000>;
+
+			lpc_kcs: lpc_kcs@7000 {
+				compatible = "nuvoton,npcm750-lpc-kcs", "simple-mfd", "syscon";
+				reg = <0x7000 0x40>;
+				reg-io-width = <1>;
+
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x40>;
+
+				kcs1: kcs1@0 {
+					compatible = "nuvoton,npcm750-kcs-bmc";
+					reg = <0x0 0x40>;
+					interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+					kcs_chan = <1>;
+					status = "disabled";
+				};
+
+				kcs2: kcs2@0 {
+					compatible = "nuvoton,npcm750-kcs-bmc";
+					reg = <0x0 0x40>;
+					interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+					kcs_chan = <2>;
+					status = "disabled";
+				};
+
+				kcs3: kcs3@0 {
+					compatible = "nuvoton,npcm750-kcs-bmc";
+					reg = <0x0 0x40>;
+					interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+					kcs_chan = <3>;
+					status = "disabled";
+				};
+			};
+
+			peci: peci-controller@f0100000 {
+				compatible = "nuvoton,npcm750-peci";
+				reg = <0xf0100000 0x200>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_APB3>;
+				cmd-timeout-ms = <1000>;
+				status = "disabled";
+			};
+
+			spi0: spi@200000 {
+				compatible = "nuvoton,npcm750-pspi";
+				reg = <0x200000 0x1000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pspi1_pins>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_APB5>;
+				clock-names = "clk_apb5";
+				resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI1>;
+				status = "disabled";
+			};
+
+			spi1: spi@201000 {
+				compatible = "nuvoton,npcm750-pspi";
+				reg = <0x201000 0x1000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pspi2_pins>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_APB5>;
+				clock-names = "clk_apb5";
+				resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI2>;
+				status = "disabled";
+			};
+
+			timer0: timer@8000 {
+				compatible = "nuvoton,npcm750-timer";
+				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x8000 0x1C>;
+				clocks = <&clk NPCM7XX_CLK_TIMER>;
+			};
+
+			watchdog0: watchdog@801C {
+				compatible = "nuvoton,npcm750-wdt";
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x801C 0x4>;
+				status = "disabled";
+				clocks = <&clk NPCM7XX_CLK_TIMER>;
+			};
+
+			watchdog1: watchdog@901C {
+				compatible = "nuvoton,npcm750-wdt";
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x901C 0x4>;
+				status = "disabled";
+				clocks = <&clk NPCM7XX_CLK_TIMER>;
+			};
+
+			watchdog2: watchdog@a01C {
+				compatible = "nuvoton,npcm750-wdt";
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xa01C 0x4>;
+				status = "disabled";
+				clocks = <&clk NPCM7XX_CLK_TIMER>;
+			};
+
+			serial0: serial@1000 {
+				compatible = "nuvoton,npcm750-uart";
+				reg = <0x1000 0x1000>;
+				clocks = <&clk NPCM7XX_CLK_UART>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial1: serial@2000 {
+				compatible = "nuvoton,npcm750-uart";
+				reg = <0x2000 0x1000>;
+				clocks = <&clk NPCM7XX_CLK_UART>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial2: serial@3000 {
+				compatible = "nuvoton,npcm750-uart";
+				reg = <0x3000 0x1000>;
+				clocks = <&clk NPCM7XX_CLK_UART>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial3: serial@4000 {
+				compatible = "nuvoton,npcm750-uart";
+				reg = <0x4000 0x1000>;
+				clocks = <&clk NPCM7XX_CLK_UART>;
+				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			rng: rng@b000 {
+				compatible = "nuvoton,npcm750-rng";
+				reg = <0xb000 0x8>;
+				status = "disabled";
+			};
+
+			adc: adc@c000 {
+				compatible = "nuvoton,npcm750-adc";
+				reg = <0xc000 0x8>;
+				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_ADC>;
+				resets = <&rstc NPCM7XX_RESET_IPSRST1 NPCM7XX_RESET_ADC>;
+				status = "disabled";
+			};
+
+			pwm_fan: pwm-fan-controller@103000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "nuvoton,npcm750-pwm-fan";
+				reg = <0x103000 0x2000>, <0x180000 0x8000>;
+				reg-names = "pwm", "fan";
+				clocks = <&clk NPCM7XX_CLK_APB3>,
+					<&clk NPCM7XX_CLK_APB4>;
+				clock-names = "pwm","fan";
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm0_pins &pwm1_pins
+						&pwm2_pins &pwm3_pins
+						&pwm4_pins &pwm5_pins
+						&pwm6_pins &pwm7_pins
+						&fanin0_pins &fanin1_pins
+						&fanin2_pins &fanin3_pins
+						&fanin4_pins &fanin5_pins
+						&fanin6_pins &fanin7_pins
+						&fanin8_pins &fanin9_pins
+						&fanin10_pins &fanin11_pins
+						&fanin12_pins &fanin13_pins
+						&fanin14_pins &fanin15_pins>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@80000 {
+				reg = <0x80000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb0_pins>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@81000 {
+				reg = <0x81000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb1_pins>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@82000 {
+				reg = <0x82000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb2_pins>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@83000 {
+				reg = <0x83000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb3_pins>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@84000 {
+				reg = <0x84000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb4_pins>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@85000 {
+				reg = <0x85000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb5_pins>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@86000 {
+				reg = <0x86000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb6_pins>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@87000 {
+				reg = <0x87000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb7_pins>;
+				status = "disabled";
+			};
+
+			i2c8: i2c@88000 {
+				reg = <0x88000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb8_pins>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@89000 {
+				reg = <0x89000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb9_pins>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@8a000 {
+				reg = <0x8a000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb10_pins>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@8b000 {
+				reg = <0x8b000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb11_pins>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@8c000 {
+				reg = <0x8c000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb12_pins>;
+				status = "disabled";
+			};
+
+			i2c13: i2c@8d000 {
+				reg = <0x8d000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb13_pins>;
+				status = "disabled";
+			};
+
+			i2c14: i2c@8e000 {
+				reg = <0x8e000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb14_pins>;
+				status = "disabled";
+			};
+
+			i2c15: i2c@8f000 {
+				reg = <0x8f000 0x1000>;
+				compatible = "nuvoton,npcm750-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk NPCM7XX_CLK_APB2>;
+				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb15_pins>;
+				status = "disabled";
+			};
+		};
+	};
+
+	pinctrl: pinctrl@f0800000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "nuvoton,npcm750-pinctrl", "syscon", "simple-mfd";
+		ranges = <0 0xf0010000 0x8000>;
+		gpio0: gpio@f0010000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x0 0x80>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 0 32>;
+		};
+		gpio1: gpio@f0011000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x1000 0x80>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 32 32>;
+		};
+		gpio2: gpio@f0012000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x2000 0x80>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 64 32>;
+		};
+		gpio3: gpio@f0013000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x3000 0x80>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 96 32>;
+		};
+		gpio4: gpio@f0014000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x4000 0x80>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 128 32>;
+		};
+		gpio5: gpio@f0015000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x5000 0x80>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 160 32>;
+		};
+		gpio6: gpio@f0016000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x6000 0x80>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 192 32>;
+		};
+		gpio7: gpio@f0017000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x7000 0x80>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&pinctrl 0 224 32>;
+		};
+
+		iox1_pins: iox1-pins {
+			groups = "iox1";
+			function = "iox1";
+		};
+		iox2_pins: iox2-pins {
+			groups = "iox2";
+			function = "iox2";
+		};
+		smb1d_pins: smb1d-pins {
+			groups = "smb1d";
+			function = "smb1d";
+		};
+		smb2d_pins: smb2d-pins {
+			groups = "smb2d";
+			function = "smb2d";
+		};
+		lkgpo1_pins: lkgpo1-pins {
+			groups = "lkgpo1";
+			function = "lkgpo1";
+		};
+		lkgpo2_pins: lkgpo2-pins {
+			groups = "lkgpo2";
+			function = "lkgpo2";
+		};
+		ioxh_pins: ioxh-pins {
+			groups = "ioxh";
+			function = "ioxh";
+		};
+		gspi_pins: gspi-pins {
+			groups = "gspi";
+			function = "gspi";
+		};
+		smb5b_pins: smb5b-pins {
+			groups = "smb5b";
+			function = "smb5b";
+		};
+		smb5c_pins: smb5c-pins {
+			groups = "smb5c";
+			function = "smb5c";
+		};
+		lkgpo0_pins: lkgpo0-pins {
+			groups = "lkgpo0";
+			function = "lkgpo0";
+		};
+		pspi2_pins: pspi2-pins {
+			groups = "pspi2";
+			function = "pspi2";
+		};
+		smb4den_pins: smb4den-pins {
+			groups = "smb4den";
+			function = "smb4den";
+		};
+		smb4b_pins: smb4b-pins {
+			groups = "smb4b";
+			function = "smb4b";
+		};
+		smb4c_pins: smb4c-pins {
+			groups = "smb4c";
+			function = "smb4c";
+		};
+		smb15_pins: smb15-pins {
+			groups = "smb15";
+			function = "smb15";
+		};
+		smb4d_pins: smb4d-pins {
+			groups = "smb4d";
+			function = "smb4d";
+		};
+		smb14_pins: smb14-pins {
+			groups = "smb14";
+			function = "smb14";
+		};
+		smb5_pins: smb5-pins {
+			groups = "smb5";
+			function = "smb5";
+		};
+		smb4_pins: smb4-pins {
+			groups = "smb4";
+			function = "smb4";
+		};
+		smb3_pins: smb3-pins {
+			groups = "smb3";
+			function = "smb3";
+		};
+		spi0cs1_pins: spi0cs1-pins {
+			groups = "spi0cs1";
+			function = "spi0cs1";
+		};
+		spi0cs2_pins: spi0cs2-pins {
+			groups = "spi0cs2";
+			function = "spi0cs2";
+		};
+		spi0cs3_pins: spi0cs3-pins {
+			groups = "spi0cs3";
+			function = "spi0cs3";
+		};
+		smb3c_pins: smb3c-pins {
+			groups = "smb3c";
+			function = "smb3c";
+		};
+		smb3b_pins: smb3b-pins {
+			groups = "smb3b";
+			function = "smb3b";
+		};
+		bmcuart0a_pins: bmcuart0a-pins {
+			groups = "bmcuart0a";
+			function = "bmcuart0a";
+		};
+		uart1_pins: uart1-pins {
+			groups = "uart1";
+			function = "uart1";
+		};
+		jtag2_pins: jtag2-pins {
+			groups = "jtag2";
+			function = "jtag2";
+		};
+		bmcuart1_pins: bmcuart1-pins {
+			groups = "bmcuart1";
+			function = "bmcuart1";
+		};
+		uart2_pins: uart2-pins {
+			groups = "uart2";
+			function = "uart2";
+		};
+		bmcuart0b_pins: bmcuart0b-pins {
+			groups = "bmcuart0b";
+			function = "bmcuart0b";
+		};
+		r1err_pins: r1err-pins {
+			groups = "r1err";
+			function = "r1err";
+		};
+		r1md_pins: r1md-pins {
+			groups = "r1md";
+			function = "r1md";
+		};
+		smb3d_pins: smb3d-pins {
+			groups = "smb3d";
+			function = "smb3d";
+		};
+		fanin0_pins: fanin0-pins {
+			groups = "fanin0";
+			function = "fanin0";
+		};
+		fanin1_pins: fanin1-pins {
+			groups = "fanin1";
+			function = "fanin1";
+		};
+		fanin2_pins: fanin2-pins {
+			groups = "fanin2";
+			function = "fanin2";
+		};
+		fanin3_pins: fanin3-pins {
+			groups = "fanin3";
+			function = "fanin3";
+		};
+		fanin4_pins: fanin4-pins {
+			groups = "fanin4";
+			function = "fanin4";
+		};
+		fanin5_pins: fanin5-pins {
+			groups = "fanin5";
+			function = "fanin5";
+		};
+		fanin6_pins: fanin6-pins {
+			groups = "fanin6";
+			function = "fanin6";
+		};
+		fanin7_pins: fanin7-pins {
+			groups = "fanin7";
+			function = "fanin7";
+		};
+		fanin8_pins: fanin8-pins {
+			groups = "fanin8";
+			function = "fanin8";
+		};
+		fanin9_pins: fanin9-pins {
+			groups = "fanin9";
+			function = "fanin9";
+		};
+		fanin10_pins: fanin10-pins {
+			groups = "fanin10";
+			function = "fanin10";
+		};
+		fanin11_pins: fanin11-pins {
+			groups = "fanin11";
+			function = "fanin11";
+		};
+		fanin12_pins: fanin12-pins {
+			groups = "fanin12";
+			function = "fanin12";
+		};
+		fanin13_pins: fanin13-pins {
+			groups = "fanin13";
+			function = "fanin13";
+		};
+		fanin14_pins: fanin14-pins {
+			groups = "fanin14";
+			function = "fanin14";
+		};
+		fanin15_pins: fanin15-pins {
+			groups = "fanin15";
+			function = "fanin15";
+		};
+		pwm0_pins: pwm0-pins {
+			groups = "pwm0";
+			function = "pwm0";
+		};
+		pwm1_pins: pwm1-pins {
+			groups = "pwm1";
+			function = "pwm1";
+		};
+		pwm2_pins: pwm2-pins {
+			groups = "pwm2";
+			function = "pwm2";
+		};
+		pwm3_pins: pwm3-pins {
+			groups = "pwm3";
+			function = "pwm3";
+		};
+		r2_pins: r2-pins {
+			groups = "r2";
+			function = "r2";
+		};
+		r2err_pins: r2err-pins {
+			groups = "r2err";
+			function = "r2err";
+		};
+		r2md_pins: r2md-pins {
+			groups = "r2md";
+			function = "r2md";
+		};
+		ga20kbc_pins: ga20kbc-pins {
+			groups = "ga20kbc";
+			function = "ga20kbc";
+		};
+		smb5d_pins: smb5d-pins {
+			groups = "smb5d";
+			function = "smb5d";
+		};
+		lpc_pins: lpc-pins {
+			groups = "lpc";
+			function = "lpc";
+		};
+		espi_pins: espi-pins {
+			groups = "espi";
+			function = "espi";
+		};
+		rg1_pins: rg1-pins {
+			groups = "rg1";
+			function = "rg1";
+		};
+		rg1mdio_pins: rg1mdio-pins {
+			groups = "rg1mdio";
+			function = "rg1mdio";
+		};
+		rg2_pins: rg2-pins {
+			groups = "rg2";
+			function = "rg2";
+		};
+		ddr_pins: ddr-pins {
+			groups = "ddr";
+			function = "ddr";
+		};
+		smb0_pins: smb0-pins {
+			groups = "smb0";
+			function = "smb0";
+		};
+		smb1_pins: smb1-pins {
+			groups = "smb1";
+			function = "smb1";
+		};
+		smb2_pins: smb2-pins {
+			groups = "smb2";
+			function = "smb2";
+		};
+		smb2c_pins: smb2c-pins {
+			groups = "smb2c";
+			function = "smb2c";
+		};
+		smb2b_pins: smb2b-pins {
+			groups = "smb2b";
+			function = "smb2b";
+		};
+		smb1c_pins: smb1c-pins {
+			groups = "smb1c";
+			function = "smb1c";
+		};
+		smb1b_pins: smb1b-pins {
+			groups = "smb1b";
+			function = "smb1b";
+		};
+		smb8_pins: smb8-pins {
+			groups = "smb8";
+			function = "smb8";
+		};
+		smb9_pins: smb9-pins {
+			groups = "smb9";
+			function = "smb9";
+		};
+		smb10_pins: smb10-pins {
+			groups = "smb10";
+			function = "smb10";
+		};
+		smb11_pins: smb11-pins {
+			groups = "smb11";
+			function = "smb11";
+		};
+		sd1_pins: sd1-pins {
+			groups = "sd1";
+			function = "sd1";
+		};
+		sd1pwr_pins: sd1pwr-pins {
+			groups = "sd1pwr";
+			function = "sd1pwr";
+		};
+		pwm4_pins: pwm4-pins {
+			groups = "pwm4";
+			function = "pwm4";
+		};
+		pwm5_pins: pwm5-pins {
+			groups = "pwm5";
+			function = "pwm5";
+		};
+		pwm6_pins: pwm6-pins {
+			groups = "pwm6";
+			function = "pwm6";
+		};
+		pwm7_pins: pwm7-pins {
+			groups = "pwm7";
+			function = "pwm7";
+		};
+		mmc8_pins: mmc8-pins {
+			groups = "mmc8";
+			function = "mmc8";
+		};
+		mmc_pins: mmc-pins {
+			groups = "mmc";
+			function = "mmc";
+		};
+		mmcwp_pins: mmcwp-pins {
+			groups = "mmcwp";
+			function = "mmcwp";
+		};
+		mmccd_pins: mmccd-pins {
+			groups = "mmccd";
+			function = "mmccd";
+		};
+		mmcrst_pins: mmcrst-pins {
+			groups = "mmcrst";
+			function = "mmcrst";
+		};
+		clkout_pins: clkout-pins {
+			groups = "clkout";
+			function = "clkout";
+		};
+		serirq_pins: serirq-pins {
+			groups = "serirq";
+			function = "serirq";
+		};
+		lpcclk_pins: lpcclk-pins {
+			groups = "lpcclk";
+			function = "lpcclk";
+		};
+		scipme_pins: scipme-pins {
+			groups = "scipme";
+			function = "scipme";
+		};
+		sci_pins: sci-pins {
+			groups = "sci";
+			function = "sci";
+		};
+		smb6_pins: smb6-pins {
+			groups = "smb6";
+			function = "smb6";
+		};
+		smb7_pins: smb7-pins {
+			groups = "smb7";
+			function = "smb7";
+		};
+		pspi1_pins: pspi1-pins {
+			groups = "pspi1";
+			function = "pspi1";
+		};
+		faninx_pins: faninx-pins {
+			groups = "faninx";
+			function = "faninx";
+		};
+		r1_pins: r1-pins {
+			groups = "r1";
+			function = "r1";
+		};
+		spi3_pins: spi3-pins {
+			groups = "spi3";
+			function = "spi3";
+		};
+		spi3cs1_pins: spi3cs1-pins {
+			groups = "spi3cs1";
+			function = "spi3cs1";
+		};
+		spi3quad_pins: spi3quad-pins {
+			groups = "spi3quad";
+			function = "spi3quad";
+		};
+		spi3cs2_pins: spi3cs2-pins {
+			groups = "spi3cs2";
+			function = "spi3cs2";
+		};
+		spi3cs3_pins: spi3cs3-pins {
+			groups = "spi3cs3";
+			function = "spi3cs3";
+		};
+		nprd_smi_pins: nprd-smi-pins {
+			groups = "nprd_smi";
+			function = "nprd_smi";
+		};
+		smb0b_pins: smb0b-pins {
+			groups = "smb0b";
+			function = "smb0b";
+		};
+		smb0c_pins: smb0c-pins {
+			groups = "smb0c";
+			function = "smb0c";
+		};
+		smb0den_pins: smb0den-pins {
+			groups = "smb0den";
+			function = "smb0den";
+		};
+		smb0d_pins: smb0d-pins {
+			groups = "smb0d";
+			function = "smb0d";
+		};
+		ddc_pins: ddc-pins {
+			groups = "ddc";
+			function = "ddc";
+		};
+		rg2mdio_pins: rg2mdio-pins {
+			groups = "rg2mdio";
+			function = "rg2mdio";
+		};
+		wdog1_pins: wdog1-pins {
+			groups = "wdog1";
+			function = "wdog1";
+		};
+		wdog2_pins: wdog2-pins {
+			groups = "wdog2";
+			function = "wdog2";
+		};
+		smb12_pins: smb12-pins {
+			groups = "smb12";
+			function = "smb12";
+		};
+		smb13_pins: smb13-pins {
+			groups = "smb13";
+			function = "smb13";
+		};
+		spix_pins: spix-pins {
+			groups = "spix";
+			function = "spix";
+		};
+		spixcs1_pins: spixcs1-pins {
+			groups = "spixcs1";
+			function = "spixcs1";
+		};
+		clkreq_pins: clkreq-pins {
+			groups = "clkreq";
+			function = "clkreq";
+		};
+		hgpio0_pins: hgpio0-pins {
+			groups = "hgpio0";
+			function = "hgpio0";
+		};
+		hgpio1_pins: hgpio1-pins {
+			groups = "hgpio1";
+			function = "hgpio1";
+		};
+		hgpio2_pins: hgpio2-pins {
+			groups = "hgpio2";
+			function = "hgpio2";
+		};
+		hgpio3_pins: hgpio3-pins {
+			groups = "hgpio3";
+			function = "hgpio3";
+		};
+		hgpio4_pins: hgpio4-pins {
+			groups = "hgpio4";
+			function = "hgpio4";
+		};
+		hgpio5_pins: hgpio5-pins {
+			groups = "hgpio5";
+			function = "hgpio5";
+		};
+		hgpio6_pins: hgpio6-pins {
+			groups = "hgpio6";
+			function = "hgpio6";
+		};
+		hgpio7_pins: hgpio7-pins {
+			groups = "hgpio7";
+			function = "hgpio7";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts
new file mode 100644
index 000000000000..9f64c85e1c20
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts
@@ -0,0 +1,1135 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020 Quanta Computer Inc. George.Hung@quantatw.com
+
+/dts-v1/;
+#include "nuvoton-npcm730.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Quanta GBS Board (Device Tree)";
+	compatible = "quanta,gbs-bmc","nuvoton,npcm730";
+
+	aliases {
+		ethernet1 = &gmac0;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
+		i2c16 = &i2c0_slotPE0_0;
+		i2c17 = &i2c0_slotPE1_1;
+		i2c18 = &i2c0_slotUSB_2;
+		i2c19 = &i2c0_3;
+		i2c20 = &i2c5_i2cool_0;
+		i2c21 = &i2c5_i2cool_1;
+		i2c22 = &i2c5_i2cool_2;
+		i2c23 = &i2c5_hsbp_fru_3;
+		i2c24 = &i2c6_u2_15_0;
+		i2c25 = &i2c6_u2_14_1;
+		i2c26 = &i2c6_u2_13_2;
+		i2c27 = &i2c6_u2_12_3;
+		i2c28 = &i2c7_u2_11_0;
+		i2c29 = &i2c7_u2_10_1;
+		i2c30 = &i2c7_u2_9_2;
+		i2c31 = &i2c7_u2_8_3;
+		i2c32 = &i2c9_vddcr_cpu;
+		i2c33 = &i2c9_vddcr_soc;
+		i2c34 = &i2c9_vddio_efgh;
+		i2c35 = &i2c9_vddio_abcd;
+		i2c36 = &i2c10_u2_7_0;
+		i2c37 = &i2c10_u2_6_1;
+		i2c38 = &i2c10_u2_5_2;
+		i2c39 = &i2c10_u2_4_3;
+		i2c40 = &i2c11_clk_buf0_0;
+		i2c41 = &i2c11_clk_buf1_1;
+		i2c42 = &i2c11_clk_buf2_2;
+		i2c43 = &i2c11_clk_buf3_3;
+		i2c44 = &i2c14_u2_3_0;
+		i2c45 = &i2c14_u2_2_1;
+		i2c46 = &i2c14_u2_1_2;
+		i2c47 = &i2c14_u2_0_3;
+		fiu0 = &fiu0;
+		fiu1 = &fiu3;
+	};
+
+	chosen {
+		stdout-path = &serial0;
+	};
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		sas-cable0 {
+			label = "sas-cable0";
+			gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+			linux,code = <73>;
+		};
+
+		sas-cable1 {
+			label = "sas-cable1";
+			gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+			linux,code = <72>;
+		};
+
+		sas-cable2 {
+			label = "sas-cable2";
+			gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <71>;
+		};
+
+		sas-cable3 {
+			label = "sas-cable3";
+			gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+			linux,code = <70>;
+		};
+
+		sata0 {
+			label = "sata0";
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <5>;
+		};
+
+		hsbp-cable {
+			label = "hsbp-cable";
+			gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			linux,code = <57>;
+		};
+
+		fanbd-cable {
+			label = "fanbd-cable";
+			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+			linux,code = <58>;
+		};
+
+		bp12v-cable {
+			label = "bp12v-cable";
+			gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+			linux,code = <69>;
+		};
+
+		pe-slot0 {
+			label = "pe-slot0";
+			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+			linux,code = <120>;
+		};
+
+		pe-slot1 {
+			label = "pe-slot1";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+			linux,code = <121>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 1>, <&adc 2>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat { /* gpio153 */
+			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		attention { /* gpio215 */
+			gpios = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		sys_boot_status { /* gpio216 */
+			gpios = <&gpio6 24 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+			retain-state-shutdown;
+		};
+
+		bmc_fault { /* gpio217 */
+			gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "panic";
+			panic-indicator;
+		};
+
+		led_u2_0_locate {
+			gpios = <&pca9535_ledlocate 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_1_locate {
+			gpios = <&pca9535_ledlocate 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_2_locate {
+			gpios = <&pca9535_ledlocate 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_3_locate {
+			gpios = <&pca9535_ledlocate 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_4_locate {
+			gpios = <&pca9535_ledlocate 7 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_5_locate {
+			gpios = <&pca9535_ledlocate 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_6_locate {
+			gpios = <&pca9535_ledlocate 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_7_locate {
+			gpios = <&pca9535_ledlocate 4 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_8_locate {
+			gpios = <&pca9535_ledlocate 11 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_9_locate {
+			gpios = <&pca9535_ledlocate 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_10_locate {
+			gpios = <&pca9535_ledlocate 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_11_locate {
+			gpios = <&pca9535_ledlocate 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_12_locate {
+			gpios = <&pca9535_ledlocate 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_13_locate {
+			gpios = <&pca9535_ledlocate 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_14_locate {
+			gpios = <&pca9535_ledlocate 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_15_locate {
+			gpios = <&pca9535_ledlocate 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_0_fault {
+			gpios = <&pca9535_ledfault 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_1_fault {
+			gpios = <&pca9535_ledfault 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_2_fault {
+			gpios = <&pca9535_ledfault 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_3_fault {
+			gpios = <&pca9535_ledfault 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_4_fault {
+			gpios = <&pca9535_ledfault 7 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_5_fault {
+			gpios = <&pca9535_ledfault 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_6_fault {
+			gpios = <&pca9535_ledfault 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_7_fault {
+			gpios = <&pca9535_ledfault 4 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_8_fault {
+			gpios = <&pca9535_ledfault 11 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_9_fault {
+			gpios = <&pca9535_ledfault 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_10_fault {
+			gpios = <&pca9535_ledfault 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_11_fault {
+			gpios = <&pca9535_ledfault 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_12_fault {
+			gpios = <&pca9535_ledfault 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_13_fault {
+			gpios = <&pca9535_ledfault 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_14_fault {
+			gpios = <&pca9535_ledfault 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_u2_15_fault {
+			gpios = <&pca9535_ledfault 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+	};
+
+	seven-seg-disp {
+		compatible = "seven-seg-gpio-dev";
+		refresh-interval-ms = /bits/ 16 <600>;
+		clock-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+		data-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+		clear-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	pcie-slot {
+		pcie1: pcie-slot@1 {
+			label = "PE0";
+		};
+		pcie2: pcie-slot@2 {
+			label = "PE1";
+		};
+	};
+};
+
+&fiu0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0cs1_pins>;
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <2>;
+		label = "bmc";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			u-boot@0 {
+				label = "u-boot";
+				reg = <0x0000000 0xf0000>;
+			};
+			image-descriptor@f0000 {
+				label = "image-descriptor";
+				reg = <0xf0000 0x10000>;
+			};
+			hoth-update@100000 {
+				label = "hoth-update";
+				reg = <0x100000 0x100000>;
+			};
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x200000 0x500000>;
+			};
+			rofs@700000 {
+				label = "rofs";
+				reg = <0x700000 0x35f0000>;
+			};
+			rwfs@3cf0000 {
+				label = "rwfs";
+				reg = <0x3cf0000 0x300000>;
+			};
+			hoth-mailbox@3ff0000 {
+				label = "hoth-mailbox";
+				reg = <0x3ff0000 0x10000>;
+			};
+		};
+	};
+};
+
+&fiu3 {
+	pinctrl-0 = <&spi3_pins>, <&spi3cs1_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <2>;
+		m25p,fast-read;
+		label = "pnor";
+	};
+	flash@1 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1>;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <2>;
+		m25p,fast-read;
+	};
+};
+
+&gcr {
+	serial_port_mux: uart-mux-controller {
+		compatible = "mmio-mux";
+		#mux-control-cells = <1>;
+		mux-reg-masks = <0x38 0x07>;
+		idle-states = <2>; /* Serial port mode 3 (takeover) */
+	};
+
+	uart1_mode_mux: uart1-mode-mux-controller {
+		compatible = "mmio-mux";
+		#mux-control-cells = <1>;
+		mux-reg-masks = <0x64 0x01000000>;
+		idle-states = <0>; /* Set UART1 mode to normal (follow SPMOD) */
+	};
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii-id";
+	snps,eee-force-disable;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&watchdog1 {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&serial3 {
+	status = "okay";
+};
+
+&adc {
+	#io-channel-cells = <1>;
+	status = "okay";
+};
+
+&lpc_kcs {
+	kcs1: kcs1@0 {
+		status = "okay";
+	};
+
+	kcs2: kcs2@0 {
+		status = "okay";
+	};
+
+	kcs3: kcs3@0 {
+		status = "okay";
+	};
+};
+
+&spi1 {
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; /* dummy - gpio147 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio224ol_pins &gpio227o_pins
+			&gpio228_pins>;
+	status = "okay";
+
+	jtag_master@0 {
+		compatible = "nuvoton,npcm750-jtag-master";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+		status = "okay";
+
+		pinctrl-names = "pspi", "gpio";
+		pinctrl-0 = <&pspi2_pins>;
+		pinctrl-1 = <&gpio224ol_pins &gpio227o_pins
+				&gpio228_pins>;
+
+		tck-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		tdi-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
+		tdo-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+		tms-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+		reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+
+		i2c0_slotPE0_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			pcie-slot = &pcie1;
+		};
+
+		i2c0_slotPE1_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			pcie-slot = &pcie2;
+		};
+
+		i2c0_slotUSB_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pca9535_ifdet: pca9535-ifdet@24 {
+		compatible = "nxp,pca9535";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9535_pwren: pca9535-pwren@20 {
+		compatible = "nxp,pca9535";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"pwr_u2_3_en","pwr_u2_2_en",
+			"pwr_u2_1_en","pwr_u2_0_en",
+			"pwr_u2_7_en","pwr_u2_6_en",
+			"pwr_u2_5_en","pwr_u2_4_en",
+			"pwr_u2_11_en","pwr_u2_10_en",
+			"pwr_u2_9_en","pwr_u2_8_en",
+			"pwr_u2_15_en","pwr_u2_14_en",
+			"pwr_u2_13_en","pwr_u2_12_en";
+	};
+
+	pca9535_pwrgd: pca9535-pwrgd@21 {
+		compatible = "nxp,pca9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9535_ledlocate: pca9535-ledlocate@22 {
+		compatible = "nxp,pca9535";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+	};
+
+	pca9535_ledfault: pca9535-ledfault@23 {
+		compatible = "nxp,pca9535";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+	};
+
+	pca9535_pwrdisable: pca9535-pwrdisable@25 {
+		compatible = "nxp,pca9535";
+		reg = <0x25>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"u2_3_pwr_dis","u2_2_pwr_dis",
+			"u2_1_pwr_dis","u2_0_pwr_dis",
+			"u2_7_pwr_dis","u2_6_pwr_dis",
+			"u2_5_pwr_dis","u2_4_pwr_dis",
+			"u2_11_pwr_dis","u2_10_pwr_dis",
+			"u2_9_pwr_dis","u2_8_pwr_dis",
+			"u2_15_pwr_dis","u2_14_pwr_dis",
+			"u2_13_pwr_dis","u2_12_pwr_dis";
+	};
+
+	pca9535_perst: pca9535-perst@26 {
+		compatible = "nxp,pca9535";
+		reg = <0x26>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"u2_15_perst","u2_14_perst",
+			"u2_13_perst","u2_12_perst",
+			"u2_11_perst","u2_10_perst",
+			"u2_9_perst","u2_8_perst",
+			"u2_7_perst","u2_6_perst",
+			"u2_5_perst","u2_4_perst",
+			"u2_3_perst","u2_2_perst",
+			"u2_1_perst","u2_0_perst";
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	sbtsi@4c {
+		compatible = "amd,sbtsi";
+		reg = <0x4c>;
+	};
+};
+
+&i2c5 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	mb_fru@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		i2c5_i2cool_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			max31725@54 {
+				compatible = "maxim,max31725";
+				reg = <0x54>;
+				status = "okay";
+			};
+		};
+
+		i2c5_i2cool_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			max31725@55 {
+				compatible = "maxim,max31725";
+				reg = <0x55>;
+				status = "okay";
+			};
+		};
+
+		i2c5_i2cool_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			max31725@5d {
+				compatible = "maxim,max31725";
+				reg = <0x5d>;
+				status = "okay";
+			};
+			fan_fru@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+
+		i2c5_hsbp_fru_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			hsbp_fru@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x73>;
+		i2c-mux-idle-disconnect;
+
+		i2c6_u2_15_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c6_u2_14_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c6_u2_13_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c6_u2_12_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c7 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		i2c-mux-idle-disconnect;
+
+		i2c7_u2_11_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c7_u2_10_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c7_u2_9_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c7_u2_8_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c8 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c8_adm1272: adm1272@10 {
+		compatible = "adi,adm1272";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10>;
+		shunt-resistor-micro-ohms = <300>;
+	};
+};
+
+&i2c9 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+
+		i2c9_vddcr_cpu: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			vrm@60 {
+				compatible = "isil,isl68137";
+				reg = <0x60>;
+			};
+		};
+
+		i2c9_vddcr_soc: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			vrm@61 {
+				compatible = "isil,isl68137";
+				reg = <0x61>;
+			};
+		};
+
+		i2c9_vddio_efgh: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			vrm@63 {
+				compatible = "isil,isl68137";
+				reg = <0x63>;
+			};
+		};
+
+		i2c9_vddio_abcd: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			vrm@45 {
+				compatible = "isil,isl68137";
+				reg = <0x45>;
+			};
+		};
+	};
+};
+
+&i2c10 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		i2c10_u2_7_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c10_u2_6_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c10_u2_5_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c10_u2_4_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c11 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x76>;
+		i2c-mux-idle-disconnect;
+
+		i2c11_clk_buf0_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c11_clk_buf1_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c11_clk_buf2_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c11_clk_buf3_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c12 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	max34451@4e {
+		compatible = "maxim,max34451";
+		reg = <0x4e>;
+	};
+	vrm@5d {
+		compatible = "isil,isl68137";
+		reg = <0x5d>;
+	};
+	vrm@5e {
+		compatible = "isil,isl68137";
+		reg = <0x5e>;
+	};
+};
+
+&i2c13 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c14 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c14_u2_3_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c14_u2_2_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c14_u2_1_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c14_u2_0_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&pwm_fan {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pwm0_pins &pwm1_pins
+		&pwm2_pins &pwm3_pins
+		&pwm4_pins
+		&fanin0_pins &fanin1_pins
+		&fanin2_pins &fanin3_pins
+		&fanin4_pins
+	>;
+	status = "okay";
+
+	fan@0 {
+		reg = <0x00>;
+		fan-tach-ch = /bits/ 8 <0x00>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		fan-tach-ch = /bits/ 8 <0x01>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		fan-tach-ch = /bits/ 8 <0x02>;
+	};
+	fan@3 {
+		reg = <0x04>;
+		fan-tach-ch = /bits/ 8 <0x04>;
+	};
+	fan@4 {
+		reg = <0x03>;
+		fan-tach-ch = /bits/ 8 <0x03>;
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+
+	gpio0: gpio@f0010000 {
+		/* POWER_OUT=gpio07, RESET_OUT=gpio06, PS_PWROK=gpio13 */
+		gpio-line-names =
+		/*0-31*/
+		"","","","","","","RESET_OUT","POWER_OUT",
+		"","","","","","PS_PWROK","","",
+		"","","","","","","","",
+		"","","","","","","","";
+	};
+	gpio1: gpio@f0011000 {
+		/* SIO_POWER_GOOD=gpio59 */
+		gpio-line-names =
+		/*32-63*/
+		"","","","","","","","",
+		"","","","","","","","",
+		"","","","","","","","",
+		"","","","SIO_POWER_GOOD","","","","";
+	};
+	gpio2: gpio@f0012000 {
+		bmc_usb_mux_oe_n {
+			gpio-hog;
+			gpios = <25 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "bmc-usb-mux-oe-n";
+		};
+		bmc_usb_mux_sel {
+			gpio-hog;
+			gpios = <26 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "bmc-usb-mux-sel";
+		};
+		bmc_usb2517_reset_n {
+			gpio-hog;
+			gpios = <27 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "bmc-usb2517-reset-n";
+		};
+	};
+	gpio3: gpio@f0013000 {
+		assert_cpu0_reset {
+			gpio-hog;
+			gpios = <14 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "assert-cpu0-reset";
+		};
+		assert_pwrok_cpu0_n {
+			gpio-hog;
+			gpios = <15 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "assert-pwrok-cpu0-n";
+		};
+		assert_cpu0_prochot {
+			gpio-hog;
+			gpios = <16 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "assert-cpu0-prochot";
+		};
+	};
+	gpio4: gpio@f0014000 {
+		/* POST_COMPLETE=gpio143 */
+		gpio-line-names =
+			/*128-159*/
+			"","","","","","","","",
+			"","","","","","","","POST_COMPLETE",
+			"","","","","","","","",
+			"","","","","","","","";
+	};
+	gpio5: gpio@f0015000 {
+		/* POWER_BUTTON=gpio177 */
+		gpio-line-names =
+			/*160-191*/
+			"","","","","","","","",
+			"","","","","","","","",
+			"","POWER_BUTTON","","","","","","",
+			"","","","","","","","";
+	};
+	gpio6: gpio@f0016000 {
+		/* SIO_S5=gpio199, RESET_BUTTON=gpio203 */
+		gpio-line-names =
+			/*192-223*/
+			"","","","","","","","SIO_S5",
+			"","","","RESET_BUTTON","","","","",
+			"","","","","","","","",
+			"","","","","","","","";
+	};
+
+	gpio224ol_pins: gpio224ol-pins {
+		pins = "GPIO224/SPIXCK";
+		bias-disable;
+		output-low;
+	};
+	gpio227o_pins: gpio227o-pins {
+		pins = "GPIO227/nSPIXCS0";
+		bias-disable;
+		output-high;
+	};
+	gpio228_pins: gpio228-pins {
+		pins = "GPIO228/nSPIXCS1";
+		bias-disable;
+		input-enable;
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj-gpio.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj-gpio.dtsi
new file mode 100644
index 000000000000..53cfd15fa03f
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj-gpio.dtsi
@@ -0,0 +1,477 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
+
+/ {
+	pinctrl: pinctrl@f0800000 {
+		gpio0pp_pins: gpio0pp-pins {
+			pins = "GPIO0/IOX1DI";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio1pp_pins: gpio1pp-pins {
+			pins = "GPIO1/IOX1LD";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio2pp_pins: gpio2pp-pins {
+			pins = "GPIO2/IOX1CK";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio3pp_pins: gpio3pp-pins {
+			pins = "GPIO3/IOX1D0";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio4pp_pins: gpio4pp-pins {
+			pins = "GPIO4/IOX2DI/SMB1DSDA";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio5pp_pins: gpio5pp-pins {
+			pins = "GPIO5/IOX2LD/SMB1DSCL";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio6pp_pins: gpio6pp-pins {
+			pins = "GPIO6/IOX2CK/SMB2DSDA";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio7pp_pins: gpio7pp-pins {
+			pins = "GPIO7/IOX2D0/SMB2DSCL";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio8_pins: gpio8-pins {
+			pins = "GPIO8/LKGPO1";
+			bias-disable;
+			input-enable;
+		};
+		gpio9_pins: gpio9-pins {
+			pins = "GPIO9/LKGPO2";
+			bias-disable;
+			input-enable;
+		};
+		gpio10pp_pins: gpio10pp-pins {
+			pins = "GPIO10/IOXHLD";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio11pp_pins: gpio11pp-pins {
+			pins = "GPIO11/IOXHCK";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio12_pins: gpio12-pins {
+			pins = "GPIO12/GSPICK/SMB5BSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio13_pins: gpio13-pins {
+			pins = "GPIO13/GSPIDO/SMB5BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio14_pins: gpio14-pins {
+			pins = "GPIO14/GSPIDI/SMB5CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio15od_pins: gpio15od-pins {
+			pins = "GPIO15/GSPICS/SMB5CSDA";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio17pp_pins: gpio17pp-pins {
+			pins = "GPIO17/PSPI2DI/SMB4DEN";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio18pp_pins: gpio18pp-pins {
+			pins = "GPIO18/PSPI2D0/SMB4BSDA";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio19pp_pins: gpio19pp-pins {
+			pins = "GPIO19/PSPI2CK/SMB4BSCL";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio24pp_pins: gpio24pp-pins {
+			pins = "GPIO24/IOXHDO";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio25pp_pins: gpio25pp-pins {
+			pins = "GPIO25/IOXHDI";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio37od_pins: gpio37od-pins {
+			pins = "GPIO37/SMB3CSDA";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio59pp_pins: gpio59pp-pins {
+			pins = "GPIO59/SMB3DSDA";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio60_pins: gpio60-pins {
+			pins = "GPIO60/SMB3DSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio72od_pins: gpio72od-pins {
+			pins = "GPIO72/FANIN8";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio73od_pins: gpio73od-pins {
+			pins = "GPIO73/FANIN9";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio74od_pins: gpio74od-pins {
+			pins = "GPIO74/FANIN10";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio75od_pins: gpio75od-pins {
+			pins = "GPIO75/FANIN11";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio76od_pins: gpio76od-pins {
+			pins = "GPIO76/FANIN12";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio77od_pins: gpio77od-pins {
+			pins = "GPIO77/FANIN13";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio78od_pins: gpio78od-pins {
+			pins = "GPIO78/FANIN14";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio79od_pins: gpio79od-pins {
+			pins = "GPIO79/FANIN15";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio83_pins: gpio83-pins {
+			pins = "GPIO83/PWM3";
+			bias-disable;
+			input-enable;
+		};
+		gpio84pp_pins: gpio84pp-pins {
+			pins = "GPIO84/R2TXD0";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio85pp_pins: gpio85pp-pins {
+			pins = "GPIO85/R2TXD1";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio86pp_pins: gpio86pp-pins {
+			pins = "GPIO86/R2TXEN";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio87pp_pins: gpio87pp-pins {
+			pins = "GPIO87/R2RXD0";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio88pp_pins: gpio88pp-pins {
+			pins = "GPIO88/R2RXD1";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio89pp_pins: gpio89pp-pins {
+			pins = "GPIO89/R2CRSDV";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio90pp_pins: gpio90pp-pins {
+			pins = "GPIO90/R2RXERR";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio91_pins: gpio91-pins {
+			pins = "GPIO91/R2MDC";
+			bias-disable;
+			input-enable;
+		};
+		gpio92_pins: gpio92-pins {
+			pins = "GPIO92/R2MDIO";
+			bias-disable;
+			input-enable;
+		};
+		gpio93pp_pins: gpio93pp-pins {
+			pins = "GPIO93/GA20/SMB5DSCL";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio94pp_pins: gpio94pp-pins {
+			pins = "GPIO94/nKBRST/SMB5DSDA";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio95_pins: gpio95-pins {
+			pins = "GPIO95/nLRESET/nESPIRST";
+			bias-disable;
+			input-enable;
+		};
+		gpio125pp_pins: gpio125pp-pins {
+			pins = "GPIO125/SMB1CSCL";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio126od_pins: gpio126od-pins {
+			pins = "GPIO126/SMB1BSDA";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio127od_pins: gpio127od-pins {
+			pins = "GPIO127/SMB1BSCL";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio136_pins: gpio136-pins {
+			pins = "GPIO136/SD1DT0";
+			bias-disable;
+			input-enable;
+		};
+		gpio137_pins: gpio137-pins {
+			pins = "GPIO137/SD1DT1";
+			bias-disable;
+			input-enable;
+		};
+		gpio141_pins: gpio141-pins {
+			pins = "GPIO141/SD1WP";
+			bias-disable;
+			input-enable;
+		};
+		gpio142od_pins: gpio142od-pins {
+			pins = "GPIO142/SD1CMD";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio143ol_pins: gpio143ol-pins {
+			pins = "GPIO143/SD1CD/SD1PWR";
+			bias-disable;
+			output-low;
+		};
+		gpio144_pins: gpio144-pins {
+			pins = "GPIO144/PWM4";
+			bias-disable;
+			input-enable;
+		};
+		gpio145_pins: gpio145-pins {
+			pins = "GPIO145/PWM5";
+			bias-disable;
+			input-enable;
+		};
+		gpio146_pins: gpio146-pins {
+			pins = "GPIO146/PWM6";
+			bias-disable;
+			input-enable;
+		};
+		gpio147_pins: gpio147-pins {
+			pins = "GPIO147/PWM7";
+			bias-disable;
+			input-enable;
+		};
+		gpio148_pins: gpio148-pins {
+			pins = "GPIO148/MMCDT4";
+			bias-disable;
+			input-enable;
+		};
+		gpio149_pins: gpio149-pins {
+			pins = "GPIO149/MMCDT5";
+			bias-disable;
+			input-enable;
+		};
+		gpio150_pins: gpio150-pins {
+			pins = "GPIO150/MMCDT6";
+			bias-disable;
+			input-enable;
+		};
+		gpio151_pins: gpio151-pins {
+			pins = "GPIO151/MMCDT7";
+			bias-disable;
+			input-enable;
+		};
+		gpio152_pins: gpio152-pins {
+			pins = "GPIO152/MMCCLK";
+			bias-disable;
+			input-enable;
+		};
+		gpio153_pins: gpio153-pins {
+			pins = "GPIO153/MMCWP";
+			bias-disable;
+			input-enable;
+		};
+		gpio154_pins: gpio154-pins {
+			pins = "GPIO154/MMCCMD";
+			bias-disable;
+			input-enable;
+		};
+		gpio155_pins: gpio155-pins {
+			pins = "GPIO155/nMMCCD/nMMCRST";
+			bias-disable;
+			input-enable;
+		};
+		gpio156_pins: gpio156-pins {
+			pins = "GPIO156/MMCDT0";
+			bias-disable;
+			input-enable;
+		};
+		gpio157_pins: gpio157-pins {
+			pins = "GPIO157/MMCDT1";
+			bias-disable;
+			input-enable;
+		};
+		gpio158_pins: gpio158-pins {
+			pins = "GPIO158/MMCDT2";
+			bias-disable;
+			input-enable;
+		};
+		gpio159_pins: gpio159-pins {
+			pins = "GPIO159/MMCDT3";
+			bias-disable;
+			input-enable;
+		};
+		gpio161_pins: gpio161-pins {
+			pins = "GPIO161/nLFRAME/nESPICS";
+			bias-disable;
+			input-enable;
+		};
+		gpio162_pins: gpio162-pins {
+			pins = "GPIO162/SERIRQ";
+			bias-disable;
+			input-enable;
+		};
+		gpio163_pins: gpio163-pins {
+			pins = "GPIO163/LCLK/ESPICLK";
+			bias-disable;
+			input-enable;
+		};
+		gpio164_pins: gpio164-pins {
+			pins = "GPIO164/LAD0/ESPI_IO0";
+			bias-disable;
+			input-enable;
+		};
+		gpio165_pins: gpio165-pins {
+			pins = "GPIO165/LAD1/ESPI_IO1";
+			bias-disable;
+			input-enable;
+		};
+		gpio166_pins: gpio166-pins {
+			pins = "GPIO166/LAD2/ESPI_IO2";
+			bias-disable;
+			input-enable;
+		};
+		gpio167_pins: gpio167-pins {
+			pins = "GPIO167/LAD3/ESPI_IO3";
+			bias-disable;
+			input-enable;
+		};
+		gpio168_pins: gpio168-pins {
+			pins = "GPIO168/nCLKRUN/nESPIALERT";
+			bias-disable;
+			input-enable;
+		};
+		gpio169_pins: gpio169-pins {
+			pins = "GPIO169/nSCIPME";
+			bias-disable;
+			input-enable;
+		};
+		gpio170_pins: gpio170-pins {
+			pins = "GPIO170/nSMI";
+			bias-disable;
+			input-enable;
+		};
+		gpio175od_pins: gpio175od-pins {
+			pins = "GPIO175/PSPI1CK/FANIN19";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio176od_pins: gpio176od-pins {
+			pins = "GPIO176/PSPI1DO/FANIN18";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio177_pins: gpio177-pins {
+			pins = "GPIO177/PSPI1DI/FANIN17";
+			bias-disable;
+			input-enable;
+		};
+		gpio190od_pins: gpio190od-pins {
+			pins = "GPIO190/nPRD_SMI";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio191_pins: gpio191-pins {
+			pins = "GPIO191";
+			bias-disable;
+			input-enable;
+		};
+		gpio192_pins: gpio192-pins {
+			pins = "GPIO192";
+			bias-disable;
+			input-enable;
+		};
+		gpio194pp_pins: gpio194pp-pins {
+			pins = "GPIO194/SMB0BSCL";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio195od_pins: gpio195od-pins {
+			pins = "GPIO195/SMB0BSDA";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio196od_pins: gpio196od-pins {
+			pins = "GPIO196/SMB0CSCL";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio197od_pins: gpio197od-pins {
+			pins = "GPIO197/SMB0DEN";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio198od_pins: gpio198od-pins {
+			pins = "GPIO198/SMB0DSDA";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio199od_pins: gpio199od-pins {
+			pins = "GPIO199/SMB0DSCL";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio200pp_pins: gpio200pp-pins {
+			pins = "GPIO200/R2CK";
+			bias-disable;
+			drive-push-pull;
+		};
+		gpio202od_pins: gpio202od-pins {
+			pins = "GPIO202/SMB0CSDA";
+			bias-disable;
+			drive-open-drain;
+		};
+		gpio203_pins: gpio203-pins {
+			pins = "GPIO203/FANIN16";
+			bias-disable;
+			input-enable;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj.dts
new file mode 100644
index 000000000000..cd7843339c24
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj.dts
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Quanta Computer lnc. Fran.Hsu@quantatw.com
+
+/dts-v1/;
+#include "nuvoton-npcm730.dtsi"
+#include "nuvoton-npcm730-gsj-gpio.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Quanta GSJ Board (Device Tree v12)";
+	compatible = "nuvoton,npcm750";
+
+	aliases {
+		ethernet1 = &gmac0;
+		serial3 = &serial3;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c15 = &i2c15;
+		fiu0 = &fiu0;
+	};
+
+	chosen {
+		stdout-path = &serial3;
+	};
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-bmc-live {
+			gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		LED_U2_0_LOCATE {
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_1_LOCATE {
+			gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_2_LOCATE {
+			gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_3_LOCATE {
+			gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_4_LOCATE {
+			gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_5_LOCATE {
+			gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_BMC_TRAY_PWRGD {
+			gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_7_FAULT {
+			gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_6_LOCATE {
+			gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_7_LOCATE {
+			gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_0_FAULT {
+			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_1_FAULT {
+			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_2_FAULT {
+			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_3_FAULT {
+			gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_4_FAULT {
+			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_5_FAULT {
+			gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		LED_U2_6_FAULT {
+			gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&fiu0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0cs1_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-rx-bus-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bmc@0 {
+				label = "bmc";
+				reg = <0x000000 0x2000000>;
+			};
+			u-boot@0 {
+				label = "u-boot";
+				reg = <0x0000000 0x80000>;
+				read-only;
+			};
+			u-boot-env@100000 {
+				label = "u-boot-env";
+				reg = <0x00100000 0x40000>;
+			};
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x0200000 0x600000>;
+			};
+			rofs@800000 {
+				label = "rofs";
+				reg = <0x800000 0x1400000>;
+			};
+			rwfs@1c00000 {
+				label = "rwfs";
+				reg = <0x1c00000 0x300000>;
+			};
+			reserved@1f00000 {
+				label = "reserved";
+				reg = <0x1f00000 0x100000>;
+			};
+		};
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&watchdog1 {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&serial3 {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	lm75@5c {
+		compatible = "maxim,max31725";
+		reg = <0x5c>;
+		status = "okay";
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	lm75@5c {
+		compatible = "maxim,max31725";
+		reg = <0x5c>;
+		status = "okay";
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	lm75@5c {
+		compatible = "maxim,max31725";
+		reg = <0x5c>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	lm75@5c {
+		compatible = "maxim,max31725";
+		reg = <0x5c>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+
+	eeprom@55 {
+		compatible = "atmel,24c64";
+		reg = <0x55>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	eeprom@55 {
+		compatible = "atmel,24c64";
+		reg = <0x55>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	/* P12V Quarter Brick DC/DC Power Module Q54SH12050 @60 */
+	power-brick@36 {
+		compatible = "delta,dps800";
+		reg = <0x36>;
+	};
+
+	hotswap@15 {
+		compatible = "ti,lm5066i";
+		reg = <0x15>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	ucd90160@6b {
+		compatible = "ti,ucd90160";
+		reg = <0x6b>;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		i2c_u20: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c_u21: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c_u22: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c_u23: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		i2c_u24: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c_u25: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c_u26: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		i2c_u27: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&pwm_fan {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins &pwm1_pins &pwm2_pins
+			&fanin0_pins &fanin1_pins
+			&fanin2_pins &fanin3_pins
+			&fanin4_pins &fanin5_pins>;
+	status = "okay";
+
+	fan@0 {
+		reg = <0x00>;
+		fan-tach-ch = /bits/ 8 <0x00 0x01>;
+		cooling-levels = <127 255>;
+	};
+
+	fan@1 {
+		reg = <0x01>;
+		fan-tach-ch = /bits/ 8 <0x02 0x03>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+
+	fan@2 {
+		reg = <0x02>;
+		fan-tach-ch = /bits/ 8 <0x04 0x05>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			/* GPI pins*/
+			&gpio8_pins
+			&gpio9_pins
+			&gpio12_pins
+			&gpio13_pins
+			&gpio14_pins
+			&gpio60_pins
+			&gpio83_pins
+			&gpio91_pins
+			&gpio92_pins
+			&gpio95_pins
+			&gpio136_pins
+			&gpio137_pins
+			&gpio141_pins
+			&gpio144_pins
+			&gpio145_pins
+			&gpio146_pins
+			&gpio147_pins
+			&gpio148_pins
+			&gpio149_pins
+			&gpio150_pins
+			&gpio151_pins
+			&gpio152_pins
+			&gpio153_pins
+			&gpio154_pins
+			&gpio155_pins
+			&gpio156_pins
+			&gpio157_pins
+			&gpio158_pins
+			&gpio159_pins
+			&gpio161_pins
+			&gpio162_pins
+			&gpio163_pins
+			&gpio164_pins
+			&gpio165_pins
+			&gpio166_pins
+			&gpio167_pins
+			&gpio168_pins
+			&gpio169_pins
+			&gpio170_pins
+			&gpio177_pins
+			&gpio191_pins
+			&gpio192_pins
+			&gpio203_pins
+			/* GPO pins*/
+			&gpio0pp_pins
+			&gpio1pp_pins
+			&gpio2pp_pins
+			&gpio3pp_pins
+			&gpio4pp_pins
+			&gpio5pp_pins
+			&gpio6pp_pins
+			&gpio7pp_pins
+			&gpio10pp_pins
+			&gpio11pp_pins
+			&gpio15od_pins
+			&gpio17pp_pins
+			&gpio18pp_pins
+			&gpio19pp_pins
+			&gpio24pp_pins
+			&gpio25pp_pins
+			&gpio37od_pins
+			&gpio59pp_pins
+			&gpio72od_pins
+			&gpio73od_pins
+			&gpio74od_pins
+			&gpio75od_pins
+			&gpio76od_pins
+			&gpio77od_pins
+			&gpio78od_pins
+			&gpio79od_pins
+			&gpio84pp_pins
+			&gpio85pp_pins
+			&gpio86pp_pins
+			&gpio87pp_pins
+			&gpio88pp_pins
+			&gpio89pp_pins
+			&gpio90pp_pins
+			&gpio93pp_pins
+			&gpio94pp_pins
+			&gpio125pp_pins
+			&gpio126od_pins
+			&gpio127od_pins
+			&gpio142od_pins
+			&gpio143ol_pins
+			&gpio175od_pins
+			&gpio176od_pins
+			&gpio190od_pins
+			&gpio194pp_pins
+			&gpio195od_pins
+			&gpio196od_pins
+			&gpio197od_pins
+			&gpio198od_pins
+			&gpio199od_pins
+			&gpio200pp_pins
+			&gpio202od_pins
+			>;
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
new file mode 100644
index 000000000000..5787ae95d3b4
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
@@ -0,0 +1,826 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020 Fii USA Inc.
+
+/dts-v1/;
+#include "nuvoton-npcm730.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Fii Kudo Board";
+	compatible = "fii,kudo", "nuvoton,npcm730";
+
+	aliases {
+		ethernet1 = &gmac0;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		fiu0 = &fiu0;
+		fiu1 = &fiu3;
+	};
+
+	chosen {
+		stdout-path = &serial3;
+	};
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>;
+	};
+
+	jtag_master {
+		compatible = "nuvoton,npcm750-jtag-master";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		// dev/jtag0
+		dev-num = <0>;
+		// pspi or gpio
+		mode = "pspi";
+
+		// pspi2
+		pspi-controller = <2>;
+		reg = <0xf0201000 0x1000>;
+		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk NPCM7XX_CLK_APB5>;
+
+		// TCK, TDI, TDO, TMS
+		jtag-gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>,
+				<&gpio0 18 GPIO_ACTIVE_HIGH>,
+				<&gpio0 17 GPIO_ACTIVE_HIGH>,
+				<&gpio0 16 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat {
+			label = "heartbeat";
+			gpios = <&gpio0 14 1>;
+		};
+	};
+
+	pinctrl: pinctrl@f0800000 {
+		gpio61oh_pins: gpio61oh-pins {
+			pins = "GPO61/nDTR1_BOUT1/STRAP6";
+			bias-disable;
+			output-high;
+		};
+		gpio62oh_pins: gpio62oh-pins {
+			pins = "GPO62/nRTST1/STRAP5";
+			bias-disable;
+			output-high;
+		};
+		gpio161ol_pins: gpio161ol-pins {
+			pins = "GPIO161/nLFRAME/nESPICS";
+			bias-disable;
+			output-low;
+		};
+		gpio163i_pins: gpio163i-pins {
+			pins = "GPIO163/LCLK/ESPICLK";
+			bias-disable;
+			input-enable;
+		};
+		gpio167ol_pins: gpio167ol-pins {
+			pins = "GPIO167/LAD3/ESPI_IO3";
+			bias-disable;
+			output-low;
+		};
+		gpio95i_pins: gpio95i-pins {
+			pins = "GPIO95/nLRESET/nESPIRST";
+			bias-disable;
+			input-enable;
+		};
+		gpio65ol_pins: gpio65ol-pins {
+			pins = "GPIO65/FANIN1";
+			bias-disable;
+			output-low;
+		};
+		gpio66oh_pins: gpio66oh-pins {
+			pins = "GPIO66/FANIN2";
+			bias-disable;
+			output-high;
+		};
+		gpio67oh_pins: gpio67oh-pins {
+			pins = "GPIO67/FANIN3";
+			bias-disable;
+			output-high;
+		};
+		gpio68ol_pins: gpio68ol-pins {
+			pins = "GPIO68/FANIN4";
+			bias-disable;
+			output-low;
+		};
+		gpio69i_pins: gpio69i-pins {
+			pins = "GPIO69/FANIN5";
+			bias-disable;
+			input-enable;
+		};
+		gpio70ol_pins: gpio70ol-pins {
+			pins = "GPIO70/FANIN6";
+			bias-disable;
+			output-low;
+		};
+		gpio71i_pins: gpio71i-pins {
+			pins = "GPIO71/FANIN7";
+			bias-disable;
+			input-enable;
+		};
+		gpio72i_pins: gpio72i-pins {
+			pins = "GPIO72/FANIN8";
+			bias-disable;
+			input-enable;
+		};
+		gpio73i_pins: gpio73i-pins {
+			pins = "GPIO73/FANIN9";
+			bias-disable;
+			input-enable;
+		};
+		gpio74i_pins: gpio74i-pins {
+			pins = "GPIO74/FANIN10";
+			bias-disable;
+			input-enable;
+		};
+		gpio75i_pins: gpio75i-pins {
+			pins = "GPIO75/FANIN11";
+			bias-disable;
+			input-enable;
+		};
+		gpio76i_pins: gpio76i-pins {
+			pins = "GPIO76/FANIN12";
+			bias-disable;
+			input-enable;
+		};
+		gpio77i_pins: gpio77i-pins {
+			pins = "GPIO77/FANIN13";
+			bias-disable;
+			input-enable;
+		};
+		gpio78i_pins: gpio78i-pins {
+			pins = "GPIO78/FANIN14";
+			bias-disable;
+			input-enable;
+		};
+		gpio79ol_pins: gpio79ol-pins {
+			pins = "GPIO79/FANIN15";
+			bias-disable;
+			output-low;
+		};
+		gpio80oh_pins: gpio80oh-pins {
+			pins = "GPIO80/PWM0";
+			bias-disable;
+			output-high;
+		};
+		gpio81i_pins: gpio81i-pins {
+			pins = "GPIO81/PWM1";
+			bias-disable;
+			input-enable;
+		};
+		gpio82i_pins: gpio82i-pins {
+			pins = "GPIO82/PWM2";
+			bias-disable;
+			input-enable;
+		};
+		gpio83i_pins: gpio83i-pins {
+			pins = "GPIO83/PWM3";
+			bias-disable;
+			input-enable;
+		};
+		gpio144i_pins: gpio144i-pins {
+			pins = "GPIO144/PWM4";
+			bias-disable;
+			input-enable;
+		};
+		gpio145i_pins: gpio145i-pins {
+			pins = "GPIO145/PWM5";
+			bias-disable;
+			input-enable;
+		};
+		gpio146i_pins: gpio146i-pins {
+			pins = "GPIO146/PWM6";
+			bias-disable;
+			input-enable;
+		};
+		gpio147oh_pins: gpio147oh-pins {
+			pins = "GPIO147/PWM7";
+			bias-disable;
+			output-high;
+		};
+		gpio168ol_pins: gpio168ol-pins {
+			pins = "GPIO168/nCLKRUN/nESPIALERT";
+			bias-disable;
+			output-low;
+		};
+		gpio169oh_pins: gpio169oh-pins {
+			pins = "GPIO169/nSCIPME";
+			bias-disable;
+			output-high;
+		};
+		gpio170ol_pins: gpio170ol-pins {
+			pins = "GPIO170/nSMI";
+			bias-disable;
+			output-low;
+		};
+		gpio218oh_pins: gpio218oh-pins {
+			pins = "GPIO218/nWDO1";
+			bias-disable;
+			output-high;
+		};
+		gpio37i_pins: gpio37i-pins {
+			pins = "GPIO37/SMB3CSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio38i_pins: gpio38i-pins {
+			pins = "GPIO38/SMB3CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio39i_pins: gpio39i-pins {
+			pins = "GPIO39/SMB3BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio40i_pins: gpio40i-pins {
+			pins = "GPIO40/SMB3BSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio121i_pins: gpio121i-pins {
+			pins = "GPIO121/SMB2CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio122i_pins: gpio122i-pins {
+			pins = "GPIO122/SMB2BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio123i_pins: gpio123i-pins {
+			pins = "GPIO123/SMB2BSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio124i_pins: gpio124i-pins {
+			pins = "GPIO124/SMB1CSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio125i_pins: gpio125i-pins {
+			pins = "GPIO125/SMB1CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio126i_pins: gpio126i-pins {
+			pins = "GPIO126/SMB1BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio127i_pins: gpio127i-pins {
+			pins = "GPIO127/SMB1BSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio136i_pins: gpio136i-pins {
+			pins = "GPIO136/SD1DT0";
+			bias-disable;
+			input-enable;
+		};
+		gpio137oh_pins: gpio137oh-pins {
+			pins = "GPIO137/SD1DT1";
+			bias-disable;
+			output-high;
+		};
+		gpio138i_pins: gpio138i-pins {
+			pins = "GPIO138/SD1DT2";
+			bias-disable;
+			input-enable;
+		};
+		gpio139i_pins: gpio139i-pins {
+			pins = "GPIO139/SD1DT3";
+			bias-disable;
+			input-enable;
+		};
+		gpio140i_pins: gpio140i-pins {
+			pins = "GPIO140/SD1CLK";
+			bias-disable;
+			input-enable;
+		};
+		gpio141i_pins: gpio141i-pins {
+			pins = "GPIO141/SD1WP";
+			bias-disable;
+			input-enable;
+		};
+		gpio190oh_pins: gpio190oh-pins {
+			pins = "GPIO190/nPRD_SMI";
+			bias-disable;
+			output-high;
+		};
+		gpio191oh_pins: gpio191oh-pins {
+			pins = "GPIO191";
+			bias-disable;
+			output-high;
+		};
+		gpio195ol_pins: gpio195ol-pins {
+			pins = "GPIO195/SMB0BSDA";
+			bias-disable;
+			output-low;
+		};
+		gpio196ol_pins: gpio196ol-pins {
+			pins = "GPIO196/SMB0CSCL";
+			bias-disable;
+			output-low;
+		};
+		gpio199i_pins: gpio199i-pins {
+			pins = "GPIO199/SMB0DSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio202ol_pins: gpio202ol-pins {
+			pins = "GPIO202/SMB0CSDA";
+			bias-disable;
+			output-low;
+		};
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii-id";
+	snps,eee-force-disable;
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&fiu0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0cs1_pins>;
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		spi-rx-bus-width = <2>;
+		label = "bmc";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			u-boot@0 {
+				label = "u-boot";
+				reg = <0x0000000 0xC0000>;
+				read-only;
+			};
+			u-boot-env@100000 {
+				label = "u-boot-env";
+				reg = <0x00100000 0x40000>;
+			};
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x0200000 0x600000>;
+			};
+			rofs@800000 {
+				label = "rofs";
+				reg = <0x800000 0x3500000>;
+			};
+			rwfs@3d00000 {
+				label = "rwfs";
+				reg = <0x3d00000 0x300000>;
+			};
+		};
+	};
+	flash@1 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1>;
+		spi-max-frequency = <5000000>;
+		spi-rx-bus-width = <2>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			spare1@0 {
+				label = "spi0-cs1-spare1";
+				reg = <0x0 0x800000>;
+			};
+			spare2@800000 {
+				label = "spi0-cs1-spare2";
+				reg = <0x800000 0x0>;
+			};
+		};
+	};
+};
+
+&fiu3 {
+	pinctrl-0 = <&spi3_pins>;
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		spi-rx-bus-width = <2>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			system1@0 {
+				label = "bios";
+				reg = <0x0 0x0>;
+			};
+			system2@800000 {
+				label = "spi3-system2";
+				reg = <0x800000 0x0>;
+			};
+		};
+	};
+};
+
+&watchdog1 {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&serial3 {
+	status = "okay";
+};
+
+&adc {
+	#io-channel-cells = <1>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			// Rear-Fan
+			max31790@58 {
+				compatible = "maxim,max31790";
+				reg = <0x58>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			// Mid-Fan
+			max31790@58 {
+				compatible = "maxim,max31790";
+				reg = <0x58>;
+			};
+		};
+
+		i2c-bus@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			// INLET1_T
+			lm75@5c {
+				compatible = "ti,lm75";
+				reg = <0x5c>;
+			};
+		};
+
+		i2c-bus@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			// OUTLET1_T
+			lm75@5c {
+				compatible = "ti,lm75";
+				reg = <0x5c>;
+			};
+		};
+
+		i2c-bus@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			// OUTLET2_T
+			lm75@5c {
+				compatible = "ti,lm75";
+				reg = <0x5c>;
+			};
+		};
+
+		i2c-bus@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			// OUTLET3_T
+			lm75@5c {
+				compatible = "ti,lm75";
+				reg = <0x5c>;
+			};
+		};
+	};
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		i2c-bus@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			// STB-T
+			pmbus@74 {
+				compatible = "pmbus";
+				reg = <0x74>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	smpro@4f {
+		compatible = "ampere,smpro";
+		reg = <0x4f>;
+	};
+
+	smpro@4e {
+		compatible = "ampere,smpro";
+		reg = <0x4e>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		i2c-bus@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			// ADC sensors
+			adm1266@40 {
+				compatible = "adi,adm1266";
+				reg = <0x40>;
+			};
+		};
+
+		i2c-bus@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// ADC sensors
+			adm1266@41 {
+				compatible = "adi,adm1266";
+				reg = <0x41>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		i2c-bus@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			// M2_ZONE_T
+			lm75@28 {
+				compatible = "ti,lm75";
+				reg = <0x28>;
+			};
+		};
+
+		i2c-bus@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			// BATT_ZONE_T
+			lm75@29 {
+				compatible = "ti,lm75";
+				reg = <0x29>;
+			};
+		};
+
+		i2c-bus@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			// NBM1_ZONE_T
+			lm75@28 {
+				compatible = "ti,lm75";
+				reg = <0x28>;
+			};
+		};
+		i2c-bus@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			// NBM2_ZONE_T
+			lm75@29 {
+				compatible = "ti,lm75";
+				reg = <0x29>;
+			};
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&spi0 {
+	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&gpio61oh_pins
+			&gpio62oh_pins
+			&gpio161ol_pins
+			&gpio163i_pins
+			&gpio167ol_pins
+			&gpio95i_pins
+			&gpio65ol_pins
+			&gpio66oh_pins
+			&gpio67oh_pins
+			&gpio68ol_pins
+			&gpio69i_pins
+			&gpio70ol_pins
+			&gpio71i_pins
+			&gpio72i_pins
+			&gpio73i_pins
+			&gpio74i_pins
+			&gpio75i_pins
+			&gpio76i_pins
+			&gpio77i_pins
+			&gpio78i_pins
+			&gpio79ol_pins
+			&gpio80oh_pins
+			&gpio81i_pins
+			&gpio82i_pins
+			&gpio83i_pins
+			&gpio144i_pins
+			&gpio145i_pins
+			&gpio146i_pins
+			&gpio147oh_pins
+			&gpio168ol_pins
+			&gpio169oh_pins
+			&gpio170ol_pins
+			&gpio218oh_pins
+			&gpio37i_pins
+			&gpio38i_pins
+			&gpio39i_pins
+			&gpio40i_pins
+			&gpio121i_pins
+			&gpio122i_pins
+			&gpio123i_pins
+			&gpio124i_pins
+			&gpio125i_pins
+			&gpio126i_pins
+			&gpio127i_pins
+			&gpio136i_pins
+			&gpio137oh_pins
+			&gpio138i_pins
+			&gpio139i_pins
+			&gpio140i_pins
+			&gpio141i_pins
+			&gpio190oh_pins
+			&gpio191oh_pins
+			&gpio195ol_pins
+			&gpio196ol_pins
+			&gpio199i_pins
+			&gpio202ol_pins
+			>;
+};
+
+&gcr {
+	serial_port_mux: mux-controller {
+		compatible = "mmio-mux";
+		#mux-control-cells = <1>;
+
+		mux-reg-masks = <0x38 0x07>;
+		idle-states = <2>;
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730.dtsi
index 6ac340533587..86ec12ec2b50 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730.dtsi
@@ -1,6 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
-// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
-// Copyright 2018 Google, Inc.
+// Copyright (c) 2020 Nuvoton Technology
 
 #include "nuvoton-common-npcm7xx.dtsi"
 
@@ -17,7 +16,7 @@
 		cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
-			clocks = <&clk 0>;
+			clocks = <&clk NPCM7XX_CLK_CPU>;
 			clock-names = "clk_cpu";
 			reg = <0>;
 			next-level-cache = <&l2>;
@@ -26,19 +25,20 @@
 		cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
-			clocks = <&clk 0>;
+			clocks = <&clk NPCM7XX_CLK_CPU>;
 			clock-names = "clk_cpu";
 			reg = <1>;
 			next-level-cache = <&l2>;
 		};
 	};
+
 	soc {
 		timer@3fe600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x3fe600 0x20>;
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
 						  IRQ_TYPE_LEVEL_HIGH)>;
-			clocks = <&clk 5>;
+			clocks = <&clk NPCM7XX_CLK_AHB>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
new file mode 100644
index 000000000000..f53d45fa1de8
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
@@ -0,0 +1,404 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
+// Copyright 2018 Google, Inc.
+
+/dts-v1/;
+#include "nuvoton-npcm750.dtsi"
+#include "dt-bindings/gpio/gpio.h"
+#include "nuvoton-npcm750-pincfg-evb.dtsi"
+
+/ {
+	model = "Nuvoton npcm750 Development Board (Device Tree)";
+	compatible = "nuvoton,npcm750-evb", "nuvoton,npcm750";
+
+	aliases {
+		ethernet2 = &gmac0;
+		ethernet3 = &gmac1;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		fiu0 = &fiu0;
+		fiu1 = &fiu3;
+		fiu2 = &fiux;
+	};
+
+	chosen {
+		stdout-path = &serial3;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x20000000>;
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gmac1 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&fiu0 {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-rx-bus-width = <2>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bbuboot1@0 {
+				label = "bb-uboot-1";
+				reg = <0x0000000 0x80000>;
+				read-only;
+				};
+			bbuboot2@80000 {
+				label = "bb-uboot-2";
+				reg = <0x0080000 0x80000>;
+				read-only;
+				};
+			envparam@100000 {
+				label = "env-param";
+				reg = <0x0100000 0x40000>;
+				read-only;
+				};
+			spare@140000 {
+				label = "spare";
+				reg = <0x0140000 0xC0000>;
+				};
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x0200000 0x400000>;
+				};
+			rootfs@600000 {
+				label = "rootfs";
+				reg = <0x0600000 0x700000>;
+				};
+			spare1@d00000 {
+				label = "spare1";
+				reg = <0x0D00000 0x200000>;
+				};
+			spare2@f00000 {
+				label = "spare2";
+				reg = <0x0F00000 0x200000>;
+				};
+			spare3@1100000 {
+				label = "spare3";
+				reg = <0x1100000 0x200000>;
+				};
+			spare4@1300000 {
+				label = "spare4";
+				reg = <0x1300000 0x0>;
+			};
+		};
+	};
+};
+
+&fiu3 {
+	pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>;
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-rx-bus-width = <2>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			system1@0 {
+				label = "spi3-system1";
+				reg = <0x0 0x0>;
+			};
+		};
+	};
+};
+
+&fiux {
+	spix-mode;
+};
+
+&watchdog1 {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&serial3 {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&lpc_kcs {
+	kcs1: kcs1@0 {
+		status = "okay";
+	};
+
+	kcs2: kcs2@0 {
+		status = "okay";
+	};
+
+	kcs3: kcs3@0 {
+		status = "okay";
+	};
+};
+
+/* lm75 on SVB */
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+	lm75@48 {
+		compatible = "lm75";
+		reg = <0x48>;
+		status = "okay";
+	};
+};
+
+/* lm75 on EB */
+&i2c1 {
+	clock-frequency = <100000>;
+	status = "okay";
+	lm75@48 {
+		compatible = "lm75";
+		reg = <0x48>;
+		status = "okay";
+	};
+};
+
+/* tmp100 on EB */
+&i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+	tmp100@48 {
+		compatible = "tmp100";
+		reg = <0x48>;
+		status = "okay";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c5 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+/* tmp100 on SVB */
+&i2c6 {
+	clock-frequency = <100000>;
+	status = "okay";
+	tmp100@48 {
+		compatible = "tmp100";
+		reg = <0x48>;
+		status = "okay";
+	};
+};
+
+&i2c7 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c8 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c9 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c10 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c11 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c14 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&pwm_fan {
+	status = "okay";
+	fan@0 {
+		reg = <0x00>;
+		fan-tach-ch = /bits/ 8 <0x00 0x01>;
+		cooling-levels = <127 255>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		fan-tach-ch = /bits/ 8 <0x02 0x03>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		fan-tach-ch = /bits/ 8 <0x04 0x05>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		fan-tach-ch = /bits/ 8 <0x06 0x07>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		fan-tach-ch = /bits/ 8 <0x08 0x09>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		fan-tach-ch = /bits/ 8 <0x0A 0x0B>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		fan-tach-ch = /bits/ 8 <0x0C 0x0D>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@7 {
+		reg = <0x07>;
+		fan-tach-ch = /bits/ 8 <0x0E 0x0F>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+};
+
+&spi0 {
+	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+	flash@0 {
+		compatible = "winbond,w25q128",
+		"jedec,spi-nor";
+		reg = <0x0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <5000000>;
+		partition@0 {
+			label = "spi0_spare1";
+			reg = <0x0000000 0x800000>;
+		};
+		partition@1 {
+			label = "spi0_spare2";
+			reg = <0x800000 0x0>;
+		};
+	};
+};
+
+&spi1 {
+	cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+	status = "okay";
+	flash@0 {
+		compatible = "winbond,w25q128fw",
+		"jedec,spi-nor";
+		reg = <0x0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <5000000>;
+		partition@0 {
+			label = "spi1_spare1";
+			reg = <0x0000000 0x800000>;
+		};
+		partition@1 {
+			label = "spi1_spare2";
+			reg = <0x800000 0x0>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <	&iox1_pins
+			&pin8_input
+			&pin9_output_high
+			&pin10_input
+			&pin11_output_high
+			&pin16_input
+			&pin24_output_high
+			&pin25_output_low
+			&pin32_output_high
+			&jtag2_pins
+			&pin61_output_high
+			&pin62_output_high
+			&pin63_output_high
+			&lpc_pins
+			&pin160_input
+			&pin162_input
+			&pin168_input
+			&pin169_input
+			&pin170_input
+			&pin187_output_high
+			&pin190_input
+			&pin191_output_high
+			&pin192_output_high
+			&pin197_output_low
+			&ddc_pins
+			&pin218_input
+			&pin219_output_low
+			&pin220_output_low
+			&pin221_output_high
+			&pin222_input
+			&pin223_output_low
+			&spix_pins
+			&pin228_output_low
+			&pin231_output_high
+			&pin255_input>;
+};
+
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-pincfg-evb.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-pincfg-evb.dtsi
new file mode 100644
index 000000000000..3b3806274adf
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-pincfg-evb.dtsi
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Nuvoton Technology
+
+/ {
+	pinctrl: pinctrl@f0800000 {
+		pin8_input: pin8-input {
+			pins = "GPIO8/LKGPO1";
+			bias-disable;
+			input-enable;
+		};
+		pin9_output_high: pin9-output-high {
+			pins = "GPIO9/LKGPO2";
+			bias-disable;
+			output-high;
+		};
+		pin10_input: pin10-input {
+			pins = "GPIO10/IOXHLD";
+			bias-disable;
+			input-enable;
+		};
+		pin11_output_high: pin11-output-high {
+			pins = "GPIO11/IOXHCK";
+			bias-disable;
+			output-high;
+		};
+		pin16_input: pin16-input {
+			pins = "GPIO16/LKGPO0";
+			bias-disable;
+			input-enable;
+		};
+		pin24_output_high: pin24-output-high {
+			pins = "GPIO24/IOXHDO";
+			bias-disable;
+			output-high;
+		};
+		pin25_output_low: pin25-output-low {
+			pins = "GPIO25/IOXHDI";
+			bias-disable;
+			output-low;
+		};
+		pin32_output_high: pin32-output-high {
+			pins = "GPIO32/nSPI0CS1";
+			bias-disable;
+			output-high;
+		};
+		pin61_output_high: pin61-output-high {
+			pins = "GPO61/nDTR1_BOUT1/STRAP6";
+			bias-disable;
+			output-high;
+		};
+		pin62_output_high: pin62-output-high {
+			pins = "GPO62/nRTST1/STRAP5";
+			bias-disable;
+			output-high;
+		};
+		pin63_output_high: pin63-output-high {
+			pins = "GPO63/TXD1/STRAP4";
+			bias-disable;
+			output-high;
+		};
+		pin160_input: pin160-input {
+			pins = "GPIO160/CLKOUT/RNGOSCOUT";
+			bias-disable;
+			input-enable;
+		};
+		pin162_input: pin162-input {
+			pins = "GPIO162/SERIRQ";
+			bias-disable;
+			input-enable;
+		};
+		pin168_input: pin168-input {
+			pins = "GPIO168/nCLKRUN/nESPIALERT";
+			bias-disable;
+			input-enable;
+		};
+		pin169_input: pin169-input {
+			pins = "GPIO169/nSCIPME";
+			bias-disable;
+			input-enable;
+		};
+		pin170_input: pin170-input {
+			pins = "GPIO170/nSMI";
+			bias-disable;
+			input-enable;
+		};
+		pin187_output_high: pin187-output-high {
+			pins = "GPIO187/nSPI3CS1";
+			bias-disable;
+			output-high;
+		};
+		pin190_input: pin190-input {
+			pins = "GPIO190/nPRD_SMI";
+			bias-disable;
+			input-enable;
+		};
+		pin191_output_high: pin191-output-high {
+			pins = "GPIO191";
+			bias-disable;
+			output-high;
+		};
+		pin192_output_high: pin192-output-high {
+			pins = "GPIO192";
+			bias-disable;
+			output-high;
+		};
+		pin197_output_low: pin197-output-low {
+			pins = "GPIO197/SMB0DEN";
+			bias-disable;
+			output-low;
+		};
+		pin218_input: pin218-input {
+			pins = "GPIO218/nWDO1";
+			bias-disable;
+			input-enable;
+		};
+		pin219_output_low: pin219-output-low {
+			pins = "GPIO219/nWDO2";
+			bias-disable;
+			output-low;
+		};
+		pin220_output_low: pin220-output-low {
+			pins = "GPIO220/SMB12SCL";
+			bias-disable;
+			output-low;
+		};
+		pin221_output_high: pin221-output-high {
+			pins = "GPIO221/SMB12SDA";
+			bias-disable;
+			output-high;
+		};
+		pin222_input: pin222-input {
+			pins = "GPIO222/SMB13SCL";
+			bias-disable;
+			input-enable;
+		};
+		pin223_output_low: pin223-output-low {
+			pins = "GPIO223/SMB13SDA";
+			bias-disable;
+			output-low;
+		};
+		pin228_output_low: pin228-output-low {
+			pins = "GPIO228/nSPIXCS1";
+			bias-disable;
+			output-low;
+		};
+		pin231_output_high: pin231-output-high {
+			pins = "GPIO230/SPIXD3";
+			bias-disable;
+			output-high;
+		};
+		pin255_input: pin255-input {
+			pins = "GPI255/DACOSEL";
+			bias-disable;
+			input-enable;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi
new file mode 100644
index 000000000000..230cb344b2e1
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi
@@ -0,0 +1,517 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Quanta Computer Inc. Samuel.Jiang@quantatw.com
+
+/ {
+	pinctrl: pinctrl@f0800000 {
+		gpio0ol_pins: gpio0ol-pins {
+			pins = "GPIO0/IOX1DI";
+			bias-disable;
+			output-low;
+		};
+		gpio1ol_pins: gpio1ol-pins {
+			pins = "GPIO1/IOX1LD";
+			bias-disable;
+			output-low;
+		};
+		gpio2ol_pins: gpio2ol-pins {
+			pins = "GPIO2/IOX1CK";
+			bias-disable;
+			output-low;
+		};
+		gpio3ol_pins: gpio3ol-pins {
+			pins = "GPIO3/IOX1D0";
+			bias-disable;
+			output-low;
+		};
+		gpio5_pins: gpio5-pins {
+			pins = "GPIO5/IOX2LD/SMB1DSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio6_pins: gpio6-pins {
+			pins = "GPIO6/IOX2CK/SMB2DSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio7_pins: gpio7-pins {
+			pins = "GPIO7/IOX2D0/SMB2DSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio8o_pins: gpio8o-pins {
+			pins = "GPIO8/LKGPO1";
+			bias-disable;
+			output-high;
+		};
+		gpio9ol_pins: gpio9ol-pins {
+			pins = "GPIO9/LKGPO2";
+			bias-disable;
+			output-low;
+		};
+		gpio10_pins: gpio10-pins {
+			pins = "GPIO10/IOXHLD";
+			bias-disable;
+			input-enable;
+		};
+		gpio11_pins: gpio11-pins {
+			pins = "GPIO11/IOXHCK";
+			bias-disable;
+			input-enable;
+		};
+		gpio12ol_pins: gpio12ol-pins {
+			pins = "GPIO12/GSPICK/SMB5BSCL";
+			bias-disable;
+			output-low;
+		};
+		gpio13ol_pins: gpio13ol-pins {
+			pins = "GPIO13/GSPIDO/SMB5BSDA";
+			bias-disable;
+			output-low;
+		};
+		gpio14ol_pins: gpio14ol-pins {
+			pins = "GPIO14/GSPIDI/SMB5CSCL";
+			bias-disable;
+			output-low;
+		};
+		gpio15ol_pins: gpio15ol-pins {
+			pins = "GPIO15/GSPICS/SMB5CSDA";
+			bias-disable;
+			output-low;
+		};
+		gpio20_pins: gpio20-pins {
+			pins = "GPIO20/SMB4CSDA/SMB15SDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio21_pins: gpio21-pins {
+			pins = "GPIO21/SMB4CSCL/SMB15SCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio22o_pins: gpio22o-pins {
+			pins = "GPIO22/SMB4DSDA/SMB14SDA";
+			bias-disable;
+			output-high;
+		};
+		gpio23_pins: gpio23-pins {
+			pins = "GPIO23/SMB4DSCL/SMB14SCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio24_pins: gpio24-pins {
+			pins = "GPIO24/IOXHDO";
+			bias-disable;
+			input-enable;
+		};
+		gpio25_pins: gpio25-pins {
+			pins = "GPIO25/IOXHDI";
+			bias-disable;
+			input-enable;
+		};
+		gpio30_pins: gpio30-pins {
+			pins = "GPIO30/SMB3SDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio31_pins: gpio31-pins {
+			pins = "GPIO31/SMB3SCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio37o_pins: gpio37o-pins {
+			pins = "GPIO37/SMB3CSDA";
+			bias-disable;
+			output-high;
+		};
+		gpio38_pins: gpio38-pins {
+			pins = "GPIO38/SMB3CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio39_pins: gpio39-pins {
+			pins = "GPIO39/SMB3BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio40o_pins: gpio40o-pins {
+			pins = "GPIO40/SMB3BSCL";
+			bias-disable;
+			output-high;
+		};
+		gpio59_pins: gpio59-pins {
+			pins = "GPIO59/SMB3DSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio76_pins: gpio76-pins {
+			pins = "GPIO76/FANIN12";
+			bias-disable;
+			input-enable;
+		};
+		gpio77_pins: gpio77-pins {
+			pins = "GPIO77/FANIN13";
+			bias-disable;
+			input-enable;
+		};
+		gpio78o_pins: gpio78o-pins {
+			pins = "GPIO78/FANIN14";
+			bias-disable;
+			output-high;
+		};
+		gpio79_pins: gpio79-pins {
+			pins = "GPIO79/FANIN15";
+			bias-disable;
+			input-enable;
+		};
+		gpio82_pins: gpio82-pins {
+			pins = "GPIO82/PWM2";
+			bias-disable;
+			input-enable;
+		};
+		gpio83_pins: gpio83-pins {
+			pins = "GPIO83/PWM3";
+			bias-disable;
+			input-enable;
+		};
+		gpio84_pins: gpio84-pins {
+			pins = "GPIO84/R2TXD0";
+			bias-disable;
+			input-enable;
+		};
+		gpio85o_pins: gpio85o-pins {
+			pins = "GPIO85/R2TXD1";
+			bias-disable;
+			output-high;
+		};
+		gpio86ol_pins: gpio86ol-pins {
+			pins = "GPIO86/R2TXEN";
+			bias-disable;
+			output-low;
+		};
+		gpio87_pins: gpio87-pins {
+			pins = "GPIO87/R2RXD0";
+			bias-disable;
+			input-enable;
+		};
+		gpio88_pins: gpio88-pins {
+			pins = "GPIO88/R2RXD1";
+			bias-disable;
+			input-enable;
+		};
+		gpio89_pins: gpio89-pins {
+			pins = "GPIO89/R2CRSDV";
+			bias-disable;
+			input-enable;
+		};
+		gpio90_pins: gpio90-pins {
+			pins = "GPIO90/R2RXERR";
+			bias-disable;
+			input-enable;
+		};
+		gpio93_pins: gpio93-pins {
+			pins = "GPIO93/GA20/SMB5DSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio94ol_pins: gpio94ol-pins {
+			pins = "GPIO94/nKBRST/SMB5DSDA";
+			bias-disable;
+			output-low;
+		};
+		gpio108ol_pins: gpio108ol-pins {
+			pins = "GPIO108/RG1MDC";
+			bias-disable;
+			output-low;
+		};
+		gpio109ol_pins: gpio109ol-pins {
+			pins = "GPIO109/RG1MDIO";
+			bias-disable;
+			output-low;
+		};
+		gpio110ol_pins: gpio110ol-pins {
+			pins = "GPIO110/RG2TXD0/DDRV0";
+			bias-disable;
+			output-low;
+		};
+		gpio111ol_pins: gpio111ol-pins {
+			pins = "GPIO111/RG2TXD1/DDRV1";
+			bias-disable;
+			output-low;
+		};
+		gpio112ol_pins: gpio112ol-pins {
+			pins = "GPIO112/RG2TXD2/DDRV2";
+			bias-disable;
+			output-low;
+		};
+		gpio113ol_pins: gpio113ol-pins {
+			pins = "GPIO113/RG2TXD3/DDRV3";
+			bias-disable;
+			output-low;
+		};
+		gpio114o_pins: gpio114o-pins {
+			pins = "GPIO114/SMB0SCL";
+			bias-disable;
+			output-high;
+		};
+		gpio115_pins: gpio115-pins {
+			pins = "GPIO115/SMB0SDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio120_pins: gpio120-pins {
+			pins = "GPIO120/SMB2CSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio121_pins: gpio121-pins {
+			pins = "GPIO121/SMB2CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio122_pins: gpio122-pins {
+			pins = "GPIO122/SMB2BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio123_pins: gpio123-pins {
+			pins = "GPIO123/SMB2BSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio124_pins: gpio124-pins {
+			pins = "GPIO124/SMB1CSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio125_pins: gpio125-pins {
+			pins = "GPIO125/SMB1CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio126_pins: gpio126-pins {
+			pins = "GPIO126/SMB1BSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio127o_pins: gpio127o-pins {
+			pins = "GPIO127/SMB1BSCL";
+			bias-disable;
+			output-high;
+		};
+		gpio136_pins: gpio136-pins {
+			pins = "GPIO136/SD1DT0";
+			bias-disable;
+			input-enable;
+		};
+		gpio137_pins: gpio137-pins {
+			pins = "GPIO137/SD1DT1";
+			bias-disable;
+			input-enable;
+		};
+		gpio138_pins: gpio138-pins {
+			pins = "GPIO138/SD1DT2";
+			bias-disable;
+			input-enable;
+		};
+		gpio139_pins: gpio139-pins {
+			pins = "GPIO139/SD1DT3";
+			bias-disable;
+			input-enable;
+		};
+		gpio140_pins: gpio140-pins {
+			pins = "GPIO140/SD1CLK";
+			bias-disable;
+			input-enable;
+		};
+		gpio141_pins: gpio141-pins {
+			pins = "GPIO141/SD1WP";
+			bias-disable;
+			input-enable;
+		};
+		gpio142_pins: gpio142-pins {
+			pins = "GPIO142/SD1CMD";
+			bias-disable;
+			input-enable;
+		};
+		gpio143_pins: gpio143-pins {
+			pins = "GPIO143/SD1CD/SD1PWR";
+			bias-disable;
+			input-enable;
+		};
+		gpio144_pins: gpio144-pins {
+			pins = "GPIO144/PWM4";
+			bias-disable;
+			input-enable;
+		};
+		gpio145_pins: gpio145-pins {
+			pins = "GPIO145/PWM5";
+			bias-disable;
+			input-enable;
+		};
+		gpio146_pins: gpio146-pins {
+			pins = "GPIO146/PWM6";
+			bias-disable;
+			input-enable;
+		};
+		gpio147_pins: gpio147-pins {
+			pins = "GPIO147/PWM7";
+			bias-disable;
+			input-enable;
+		};
+		gpio153o_pins: gpio153o-pins {
+			pins = "GPIO153/MMCWP";
+			bias-disable;
+			output-high;
+		};
+		gpio155_pins: gpio155-pins {
+			pins = "GPIO155/nMMCCD/nMMCRST";
+			bias-disable;
+			input-enable;
+		};
+		gpio160o_pins: gpio160o-pins {
+			pins = "GPIO160/CLKOUT/RNGOSCOUT";
+			bias-disable;
+			output-high;
+		};
+		gpio169o_pins: gpio169o-pins {
+			pins = "GPIO169/nSCIPME";
+			bias-disable;
+			output-high;
+		};
+		gpio188o_pins: gpio188o-pins {
+			pins = "GPIO188/SPI3D2/nSPI3CS2";
+			bias-disable;
+			output-high;
+		};
+		gpio189_pins: gpio189-pins {
+			pins = "GPIO189/SPI3D3/nSPI3CS3";
+			bias-disable;
+			input-enable;
+		};
+		gpio196_pins: gpio196-pins {
+			pins = "GPIO196/SMB0CSCL";
+			bias-disable;
+			input-enable;
+		};
+		gpio197_pins: gpio197-pins {
+			pins = "GPIO197/SMB0DEN";
+			bias-disable;
+			input-enable;
+		};
+		gpio198o_pins: gpio198o-pins {
+			pins = "GPIO198/SMB0DSDA";
+			bias-disable;
+			output-high;
+		};
+		gpio199o_pins: gpio199o-pins {
+			pins = "GPIO199/SMB0DSCL";
+			bias-disable;
+			output-high;
+		};
+		gpio200_pins: gpio200-pins {
+			pins = "GPIO200/R2CK";
+			input-enable;
+			bias-disable;
+		};
+		gpio202_pins: gpio202-pins {
+			pins = "GPIO202/SMB0CSDA";
+			bias-disable;
+			input-enable;
+		};
+		gpio203o_pins: gpio203o-pins {
+			pins = "GPIO203/FANIN16";
+			bias-disable;
+			output-high;
+		};
+		gpio208_pins: gpio208-pins {
+			pins = "GPIO208/RG2TXC/DVCK";
+			bias-disable;
+			input-enable;
+		};
+		gpio209ol_pins: gpio209ol-pins {
+			pins = "GPIO209/RG2TXCTL/DDRV4";
+			bias-disable;
+			output-low;
+		};
+		gpio210ol_pins: gpio210ol-pins {
+			pins = "GPIO210/RG2RXD0/DDRV5";
+			bias-disable;
+			output-low;
+		};
+		gpio211ol_pins: gpio211ol-pins {
+			pins = "GPIO211/RG2RXD1/DDRV6";
+			bias-disable;
+			output-low;
+		};
+		gpio212ol_pins: gpio212ol-pins {
+			pins = "GPIO212/RG2RXD2/DDRV7";
+			bias-disable;
+			output-low;
+		};
+		gpio213ol_pins: gpio213ol-pins {
+			pins = "GPIO213/RG2RXD3/DDRV8";
+			bias-disable;
+			output-low;
+		};
+		gpio214ol_pins: gpio214ol-pins {
+			pins = "GPIO214/RG2RXC/DDRV9";
+			bias-disable;
+			output-low;
+		};
+		gpio215ol_pins: gpio215ol-pins {
+			pins = "GPIO215/RG2RXCTL/DDRV10";
+			bias-disable;
+			output-low;
+		};
+		gpio216ol_pins: gpio216ol-pins {
+			pins = "GPIO216/RG2MDC/DDRV11";
+			bias-disable;
+			output-low;
+		};
+		gpio217ol_pins: gpio217ol-pins {
+			pins = "GPIO217/RG2MDIO/DVHSYNC";
+			bias-disable;
+			output-low;
+		};
+		gpio224_pins: gpio224-pins {
+			pins = "GPIO224/SPIXCK";
+			bias-disable;
+			input-enable;
+		};
+		gpio225ol_pins: gpio225ol-pins {
+			pins = "GPO225/SPIXD0/STRAP12";
+			bias-disable;
+			output-low;
+		};
+		gpio226ol_pins: gpio226ol-pins {
+			pins = "GPO226/SPIXD1/STRAP13";
+			bias-disable;
+			output-low;
+		};
+		gpio227ol_pins: gpio227ol-pins {
+			pins = "GPIO227/nSPIXCS0";
+			bias-disable;
+			output-low;
+		};
+		gpio228o_pins: gpio228ol-pins {
+			pins = "GPIO228/nSPIXCS1";
+			bias-disable;
+			output-high;
+		};
+		gpio229o_pins: gpio229o-pins {
+			pins = "GPO229/SPIXD2/STRAP3";
+			bias-disable;
+			output-high;
+		};
+		gpio230_pins: gpio230-pins {
+			pins = "GPIO230/SPIXD3";
+			bias-disable;
+			input-enable;
+		};
+		gpio231o_pins: gpio231o-pins {
+			pins = "GPIO231/nCLKREQ";
+			bias-disable;
+			output-high;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts
new file mode 100644
index 000000000000..baa39d0c1032
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts
@@ -0,0 +1,1052 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Nuvoton Technology <kwliu@nuvoton.com>
+// Copyright (c) 2019 Quanta Computer Inc. <Samuel.Jiang@quantatw.com>
+
+/dts-v1/;
+#include "nuvoton-npcm750.dtsi"
+#include "nuvoton-npcm750-runbmc-olympus-pincfg.dtsi"
+
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Nuvoton npcm750 RunBMC Olympus";
+	compatible = "nuvoton,npcm750";
+
+	aliases {
+		ethernet1 = &gmac0;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		fiu0 = &fiu0;
+		fiu1 = &fiu3;
+	};
+
+	chosen {
+		stdout-path = &serial3;
+	};
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat {
+		label = "heartbeat";
+			gpios = <&gpio3 14 1>;
+		};
+
+		identify {
+			label = "identify";
+			gpios = <&gpio3 15 1>;
+		};
+	};
+
+	jtag {
+		compatible = "nuvoton,npcm750-jtag";
+		enable_pspi_jtag = <1>;
+		pspi-index = <2>;
+		tck {
+			label = "tck";
+			gpios = <&gpio0 19 0>; /* gpio19 */
+			regbase = <0xf0010000 0x1000>;
+		};
+
+		tdi {
+			label = "tdi";
+			gpios = <&gpio0 18 0>; /* gpio18 */
+			regbase = <0xf0010000 0x1000>;
+		};
+
+		tdo {
+			label = "tdo";
+			gpios = <&gpio0 17 0>; /* gpio17 */
+			regbase = <0xf0010000 0x1000>;
+		};
+		tms {
+			label = "tms";
+			gpios = <&gpio0 16 0>; /* gpio16 */
+			regbase = <0xf0010000 0x1000>;
+		};
+	};
+};
+
+&fiu0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0cs1_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-rx-bus-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bmc@0 {
+				label = "bmc";
+				reg = <0x000000 0x2000000>;
+			};
+			u-boot@0 {
+				label = "u-boot";
+				reg = <0x0000000 0x80000>;
+				read-only;
+			};
+			u-boot-env@100000 {
+				label = "u-boot-env";
+				reg = <0x00100000 0x40000>;
+			};
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x0200000 0x600000>;
+			};
+			rofs@800000 {
+				label = "rofs";
+				reg = <0x800000 0x1500000>;
+			};
+			rwfs@1d00000 {
+				label = "rwfs";
+				reg = <0x1d00000 0x300000>;
+			};
+		};
+	};
+
+	flash@1 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1>;
+		npcm,fiu-rx-bus-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			spare1@0 {
+				label = "spi0-cs1-spare1";
+				reg = <0x0 0x800000>;
+			};
+			spare2@800000 {
+				label = "spi0-cs1-spare2";
+				reg = <0x800000 0x0>;
+			};
+		};
+	};
+};
+
+&fiu3 {
+	pinctrl-0 = <&spi3_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-rx-bus-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			system1@0 {
+				label = "spi3-system1";
+				reg = <0x0 0x800000>;
+			};
+			system2@800000 {
+				label = "spi3-system2";
+				reg = <0x800000 0x0>;
+			};
+		};
+	};
+};
+
+&gcr {
+	mux-controller {
+		compatible = "mmio-mux";
+		#mux-control-cells = <1>;
+
+		mux-reg-masks = <0x38 0x07>;
+		idle-states = <6>;
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii-id";
+	snps,eee-force-disable;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c_slot1a: i2c-bus@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c_slot1b: i2c-bus@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c_slot2a: i2c-bus@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c_slot2b: i2c-bus@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		i2c_slot3: i2c-bus@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c_slot4: i2c-bus@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c_slot5: i2c-bus@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c_m2_s1: i2c-bus@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c_m2_s2: i2c-bus@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c_m2_s3: i2c-bus@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c_m2_s4: i2c-bus@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	tmp421@4c {
+		compatible = "ti,tmp421";
+		reg = <0x4c>;
+	};
+
+	power-supply@58 {
+		compatible = "delta,dps800";
+		reg = <0x58>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-slave-mqueue@10 {
+		compatible = "i2c-slave-mqueue";
+		reg = <(I2C_OWN_SLAVE_ADDRESS | 0x10)>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	ina219@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+	};
+	ina219@41 {
+		compatible = "ti,ina219";
+		reg = <0x41>;
+	};
+	ina219@44 {
+		compatible = "ti,ina219";
+		reg = <0x44>;
+	};
+	ina219@45 {
+		compatible = "ti,ina219";
+		reg = <0x45>;
+	};
+	tps53679@60 {
+		compatible = "ti,tps53679";
+		reg = <0x60>;
+	};
+	tps53659@62 {
+		compatible = "ti,tps53659";
+		reg = <0x62>;
+	};
+	tps53659@64 {
+		compatible = "ti,tps53659";
+		reg = <0x64>;
+	};
+	tps53622@67 {
+		compatible = "ti,tps53622";
+		reg = <0x67>;
+	};
+	tps53622@69 {
+		compatible = "ti,tps53622";
+		reg = <0x69>;
+	};
+	tps53679@70 {
+		compatible = "ti,tps53679";
+		reg = <0x70>;
+	};
+	tps53659@72 {
+		compatible = "ti,tps53659";
+		reg = <0x72>;
+	};
+	tps53659@74 {
+		compatible = "ti,tps53659";
+		reg = <0x74>;
+	};
+	tps53622@77 {
+		compatible = "ti,tps53622";
+		reg = <0x77>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	tmp421@4c {
+		compatible = "ti,tmp421";
+		reg = <0x4c>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	adm1278@11 {
+		compatible = "adm1278";
+		reg = <0x11>;
+		Rsense = <500>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+
+	gpio: pca9555@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	pca9539_g1a: pca9539-g1a@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		reset-gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
+		G1A_P0_0 {
+			gpio-hog;
+			gpios = <0 0>;
+			output-high;
+			line-name = "TPM_BMC_ALERT_N";
+		};
+		G1A_P0_1 {
+			gpio-hog;
+			gpios = <1 0>;
+			input;
+			line-name = "FM_BIOS_TOP_SWAP";
+		};
+		G1A_P0_2 {
+			gpio-hog;
+			gpios = <2 0>;
+			input;
+			line-name = "FM_BIOS_PREFRB2_GOOD";
+		};
+		G1A_P0_3 {
+			gpio-hog;
+			gpios = <3 0>;
+			input;
+			line-name = "BMC_SATAXPCIE_0TO3_SEL";
+		};
+		G1A_P0_4 {
+			gpio-hog;
+			gpios = <4 0>;
+			input;
+			line-name = "BMC_SATAXPCIE_4TO7_SEL";
+		};
+		G1A_P0_5 {
+			gpio-hog;
+			gpios = <5 0>;
+			output-low;
+			line-name = "FM_UV_ADR_TRIGGER_EN_N";
+		};
+		G1A_P0_6 {
+			gpio-hog;
+			gpios = <6 0>;
+			input;
+			line-name = "RM_THROTTLE_EN_N";
+		};
+		G1A_P1_0 {
+			gpio-hog;
+			gpios = <8 0>;
+			input;
+			line-name = "FM_BMC_TPM_PRES_N";
+		};
+		G1A_P1_1 {
+			gpio-hog;
+			gpios = <9 0>;
+			input;
+			line-name = "FM_CPU0_SKTOCC_LVT3_N";
+		};
+		G1A_P1_2 {
+			gpio-hog;
+			gpios = <10 0>;
+			input;
+			line-name = "FM_CPU1_SKTOCC_LVT3_N";
+		};
+		G1A_P1_3 {
+			gpio-hog;
+			gpios = <11 0>;
+			input;
+			line-name = "PSU1_ALERT_N";
+		};
+		G1A_P1_4 {
+			gpio-hog;
+			gpios = <12 0>;
+			input;
+			line-name = "PSU2_ALERT_N";
+		};
+		G1A_P1_5 {
+			gpio-hog;
+			gpios = <13 0>;
+			input;
+			line-name = "H_CPU0_FAST_WAKE_LVT3_N";
+		};
+		G1A_P1_6 {
+			gpio-hog;
+			gpios = <14 0>;
+			output-high;
+			line-name = "I2C_MUX1_RESET_N";
+		};
+		G1A_P1_7 {
+			gpio-hog;
+			gpios = <15 0>;
+			input;
+			line-name = "FM_CPU_CATERR_LVT3_N";
+		};
+	};
+
+	pca9539_g1b: pca9539-g1b@75 {
+		compatible = "nxp,pca9539";
+		reg = <0x75>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		G1B_P0_0 {
+			gpio-hog;
+			gpios = <0 0>;
+			input;
+			line-name = "PVDDQ_ABC_PINALERT_N";
+		};
+		G1B_P0_1 {
+			gpio-hog;
+			gpios = <1 0>;
+			input;
+			line-name = "PVDDQ_DEF_PINALERT_N";
+		};
+		G1B_P0_2 {
+			gpio-hog;
+			gpios = <2 0>;
+			input;
+			line-name = "PVDDQ_GHJ_PINALERT_N";
+		};
+		G1B_P0_3 {
+			gpio-hog;
+			gpios = <3 0>;
+			input;
+			line-name = "PVDDQ_KLM_PINALERT_N";
+		};
+		G1B_P0_5 {
+			gpio-hog;
+			gpios = <5 0>;
+			input;
+			line-name = "FM_BOARD_REV_ID0";
+		};
+		G1B_P0_6 {
+			gpio-hog;
+			gpios = <6 0>;
+			input;
+			line-name = "FM_BOARD_REV_ID1";
+		};
+		G1B_P0_7 {
+			gpio-hog;
+			gpios = <7 0>;
+			input;
+			line-name = "FM_BOARD_REV_ID2";
+		};
+		G1B_P1_0 {
+			gpio-hog;
+			gpios = <8 0>;
+			input;
+			line-name = "FM_OC_DETECT_EN_N";
+		};
+		G1B_P1_1 {
+			gpio-hog;
+			gpios = <9 0>;
+			input;
+			line-name = "FM_FLASH_DESC_OVERRIDE";
+		};
+		G1B_P1_2 {
+			gpio-hog;
+			gpios = <10 0>;
+			output-low;
+			line-name = "FP_PWR_ID_LED_N";
+		};
+		G1B_P1_3 {
+			gpio-hog;
+			gpios = <11 0>;
+			output-low;
+			line-name = "BMC_LED_PWR_GRN";
+		};
+		G1B_P1_4 {
+			gpio-hog;
+			gpios = <12 0>;
+			output-low;
+			line-name = "BMC_LED_PWR_AMBER";
+		};
+		G1B_P1_5 {
+			gpio-hog;
+			gpios = <13 0>;
+			output-high;
+			line-name = "FM_BMC_FAULT_LED_N";
+		};
+		G1B_P1_6 {
+			gpio-hog;
+			gpios = <14 0>;
+			output-high;
+			line-name = "FM_CPLD_BMC_PWRDN_N";
+		};
+		G1B_P1_7 {
+			gpio-hog;
+			gpios = <15 0>;
+			output-high;
+			line-name = "BMC_LED_CATERR_N";
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	pca9539_g2a: pca9539-g2a@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		reset-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+		G2A_P0_0 {
+			gpio-hog;
+			gpios = <0 0>;
+			output-high;
+			line-name = "BMC_PON_RST_REQ_N";
+		};
+		G2A_P0_1 {
+			gpio-hog;
+			gpios = <1 0>;
+			output-high;
+			line-name = "BMC_RST_IND_REQ_N";
+		};
+		G2A_P0_2 {
+			gpio-hog;
+			gpios = <2 0>;
+			input;
+			line-name = "RST_BMC_RTCRST";
+		};
+		G2A_P0_3 {
+			gpio-hog;
+			gpios = <3 0>;
+			output-high;
+			line-name = "FM_BMC_PWRBTN_OUT_N";
+		};
+		G2A_P0_4 {
+			gpio-hog;
+			gpios = <4 0>;
+			output-high;
+			line-name = "RST_BMC_SYSRST_BTN_OUT_N";
+		};
+		G2A_P0_5 {
+			gpio-hog;
+			gpios = <5 0>;
+			output-high;
+			line-name = "FM_BATTERY_SENSE_EN_N";
+		};
+		G2A_P0_6 {
+			gpio-hog;
+			gpios = <6 0>;
+			output-high;
+			line-name = "FM_BMC_READY_N";
+		};
+		G2A_P0_7 {
+			gpio-hog;
+			gpios = <7 0>;
+			input;
+			line-name = "IRQ_BMC_PCH_SMI_LPC_N";
+		};
+		G2A_P1_0 {
+			gpio-hog;
+			gpios = <8 0>;
+			input;
+			line-name = "FM_SLOT4_CFG0";
+		};
+		G2A_P1_1 {
+			gpio-hog;
+			gpios = <9 0>;
+			input;
+			line-name = "FM_SLOT4_CFG1";
+		};
+		G2A_P1_2 {
+			gpio-hog;
+			gpios = <10 0>;
+			input;
+			line-name = "FM_NVDIMM_EVENT_N";
+		};
+		G2A_P1_3 {
+			gpio-hog;
+			gpios = <11 0>;
+			input;
+			line-name = "PSU1_BLADE_EN_N";
+		};
+		G2A_P1_4 {
+			gpio-hog;
+			gpios = <12 0>;
+			input;
+			line-name = "BMC_PCH_FNM";
+		};
+		G2A_P1_5 {
+			gpio-hog;
+			gpios = <13 0>;
+			input;
+			line-name = "FM_SOL_UART_CH_SEL";
+		};
+		G2A_P1_6 {
+			gpio-hog;
+			gpios = <14 0>;
+			input;
+			line-name = "FM_BIOS_POST_CMPLT_N";
+		};
+	};
+
+	pca9539_g2b: pca9539-g2b@75 {
+		compatible = "nxp,pca9539";
+		reg = <0x75>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		G2B_P0_0 {
+			gpio-hog;
+			gpios = <0 0>;
+			input;
+			line-name = "FM_CPU_MSMI_LVT3_N";
+		};
+		G2B_P0_1 {
+			gpio-hog;
+			gpios = <1 0>;
+			input;
+			line-name = "FM_BIOS_MRC_DEBUG_MSG_DIS";
+		};
+		G2B_P0_2 {
+			gpio-hog;
+			gpios = <2 0>;
+			input;
+			line-name = "FM_CPU1_DISABLE_BMC_N";
+		};
+		G2B_P0_3 {
+			gpio-hog;
+			gpios = <3 0>;
+			output-low;
+			line-name = "BMC_JTAG_SELECT";
+		};
+		G2B_P0_4 {
+			gpio-hog;
+			gpios = <4 0>;
+			output-high;
+			line-name = "PECI_MUX_SELECT";
+		};
+		G2B_P0_5 {
+			gpio-hog;
+			gpios = <5 0>;
+			output-high;
+			line-name = "I2C_MUX2_RESET_N";
+		};
+		G2B_P0_6 {
+			gpio-hog;
+			gpios = <6 0>;
+			input;
+			line-name = "FM_BMC_CPLD_PSU2_ON";
+		};
+		G2B_P0_7 {
+			gpio-hog;
+			gpios = <7 0>;
+			output-high;
+			line-name = "PSU2_ALERT_EN_N";
+		};
+		G2B_P1_0 {
+			gpio-hog;
+			gpios = <8 0>;
+			output-high;
+			line-name = "FM_CPU_BMC_INIT";
+		};
+		G2B_P1_1 {
+			gpio-hog;
+			gpios = <9 0>;
+			output-high;
+			line-name = "IRQ_BMC_PCH_SCI_LPC_N";
+		};
+		G2B_P1_2 {
+			gpio-hog;
+			gpios = <10 0>;
+			output-low;
+			line-name = "PMB_ALERT_EN_N";
+		};
+		G2B_P1_3 {
+			gpio-hog;
+			gpios = <11 0>;
+			output-high;
+			line-name = "FM_FAST_PROCHOT_EN_N";
+		};
+		G2B_P1_4 {
+			gpio-hog;
+			gpios = <12 0>;
+			output-high;
+			line-name = "BMC_NVDIMM_PRSNT_N";
+		};
+		G2B_P1_5 {
+			gpio-hog;
+			gpios = <13 0>;
+			output-low;
+			line-name = "FM_BACKUP_BIOS_SEL_H_BMC";
+		};
+		G2B_P1_6 {
+			gpio-hog;
+			gpios = <14 0>;
+			output-high;
+			line-name = "FM_PWRBRK_N";
+		};
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	tmp75@4a {
+		compatible = "ti,tmp75";
+		reg = <0x4a>;
+		status = "okay";
+	};
+	m24128_fru@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <64>;
+		status = "okay";
+	};
+};
+
+&pwm_fan {
+	pinctrl-names = "default";
+	pinctrl-0 = <   &pwm0_pins &pwm1_pins
+			&fanin0_pins &fanin1_pins
+			&fanin2_pins &fanin3_pins
+			&fanin4_pins &fanin5_pins
+			&fanin6_pins &fanin7_pins
+			&fanin8_pins &fanin9_pins
+			&fanin10_pins &fanin11_pins>;
+	status = "okay";
+
+	fan@0 {
+		reg = <0x00>;
+		fan-tach-ch = /bits/ 8 <0x00 0x01>;
+		cooling-levels = <127 255>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		fan-tach-ch = /bits/ 8 <0x02 0x03>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		fan-tach-ch = /bits/ 8 <0x04 0x05>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		fan-tach-ch = /bits/ 8 <0x06 0x07>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		fan-tach-ch = /bits/ 8 <0x08 0x09>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		fan-tach-ch = /bits/ 8 <0x0A 0x0B>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		fan-tach-ch = /bits/ 8 <0x0C 0x0D>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+	fan@7 {
+		reg = <0x07>;
+		fan-tach-ch = /bits/ 8 <0x0E 0x0F>;
+		cooling-levels = /bits/ 8 <127 255>;
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&watchdog1 {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&serial3 {
+	status = "okay";
+};
+
+&adc {
+	#io-channel-cells = <1>;
+	status = "okay";
+};
+
+&kcs1 {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+};
+
+&kcs3 {
+	status = "okay";
+};
+
+&spi0 {
+	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			/******* RunBMC inside Module pins *******/
+			&gpio0ol_pins
+			&gpio1ol_pins
+			&gpio2ol_pins
+			&gpio3ol_pins
+			&gpio8o_pins
+			&gpio9ol_pins
+			&gpio12ol_pins
+			&gpio13ol_pins
+			&gpio14ol_pins
+			&gpio15ol_pins
+			&gpio37o_pins
+			&gpio38_pins
+			&gpio39_pins
+			&gpio94ol_pins
+			&gpio108ol_pins
+			&gpio109ol_pins
+			&gpio111ol_pins
+			&gpio112ol_pins
+			&gpio113ol_pins
+			&gpio208_pins
+			&gpio209ol_pins
+			&gpio210ol_pins
+			&gpio211ol_pins
+			&gpio212ol_pins
+			&gpio213ol_pins
+			&gpio214ol_pins
+			&gpio215ol_pins
+			&gpio216ol_pins
+			&gpio217ol_pins
+			/******* RunBMC outside Connector pins *******/
+			&gpio5_pins
+			&gpio6_pins
+			&gpio7_pins
+			&gpio10_pins
+			&gpio11_pins
+			&gpio20_pins
+			&gpio21_pins
+			&gpio22o_pins
+			&gpio23_pins
+			&gpio24_pins
+			&gpio25_pins
+			&gpio30_pins
+			&gpio31_pins
+			&gpio40o_pins
+			&gpio59_pins
+			&gpio76_pins
+			&gpio77_pins
+			&gpio78o_pins
+			&gpio79_pins
+			&gpio82_pins
+			&gpio83_pins
+			&gpio84_pins
+			&gpio85o_pins
+			&gpio86ol_pins
+			&gpio87_pins
+			&gpio88_pins
+			&gpio89_pins
+			&gpio90_pins
+			&gpio93_pins
+			&gpio114o_pins
+			&gpio115_pins
+			&gpio120_pins
+			&gpio121_pins
+			&gpio122_pins
+			&gpio123_pins
+			&gpio124_pins
+			&gpio125_pins
+			&gpio126_pins
+			&gpio127o_pins
+			&gpio136_pins
+			&gpio137_pins
+			&gpio138_pins
+			&gpio139_pins
+			&gpio140_pins
+			&gpio141_pins
+			&gpio142_pins
+			&gpio143_pins
+			&gpio144_pins
+			&gpio146_pins
+			&gpio145_pins
+			&gpio147_pins
+			&gpio153o_pins
+			&gpio155_pins
+			&gpio160o_pins
+			&gpio169o_pins
+			&gpio188o_pins
+			&gpio189_pins
+			&gpio196_pins
+			&gpio197_pins
+			&gpio198o_pins
+			&gpio199o_pins
+			&gpio200_pins
+			&gpio202_pins
+			&gpio203o_pins
+			&gpio224_pins
+			&gpio225ol_pins
+			&gpio226ol_pins
+			&gpio227ol_pins
+			&gpio228o_pins
+			&gpio229o_pins
+			&gpio230_pins
+			&gpio231o_pins
+			&ddc_pins
+			&wdog1_pins
+			&wdog2_pins
+			>;
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi
new file mode 100644
index 000000000000..30eed40b89b5
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
+// Copyright 2018 Google, Inc.
+
+#include "nuvoton-common-npcm7xx.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "nuvoton,npcm750-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			clocks = <&clk NPCM7XX_CLK_CPU>;
+			clock-names = "clk_cpu";
+			reg = <0>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			clocks = <&clk NPCM7XX_CLK_CPU>;
+			clock-names = "clk_cpu";
+			reg = <1>;
+			next-level-cache = <&l2>;
+		};
+	};
+
+	soc {
+		timer@3fe600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x3fe600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&clk NPCM7XX_CLK_AHB>;
+		};
+	};
+
+	ahb {
+		gmac1: eth@f0804000 {
+			device_type = "network";
+			compatible = "snps,dwmac";
+			reg = <0xf0804000 0x2000>;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			ethernet = <1>;
+			clocks = <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "stmmaceth", "clk_gmac";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rg2_pins
+					&rg2mdio_pins>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
new file mode 100644
index 000000000000..b78c116cbc18
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+// Copyright 2021 Jonathan Neuschäfer
+
+/dts-v1/;
+
+/* The last 16 MiB are dedicated to the GPU */
+/memreserve/ 0x07000000 0x01000000;
+
+#include "nuvoton-wpcm450.dtsi"
+
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Supermicro X9SCi-LN4F BMC";
+	compatible = "supermicro,x9sci-ln4f-bmc", "nuvoton,wpcm450";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x08000000>; /* 128 MiB */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_pins>;
+
+		uid {
+			label = "UID button";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		uid {
+			label = "UID";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		heartbeat {
+			label = "heartbeat";
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&fiu {
+	status = "okay";
+
+	flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+		/* 0 */ "", "host-reset-control-n", "", "", "", "", "", "",
+		/* 8 */ "", "", "", "", "power-chassis-control-n", "", "uid-button", "";
+};
+
+&gpio1 {
+	gpio-line-names =
+		/* 0 */ "", "", "", "", "led-heartbeat", "", "", "led-uid",
+		/* 8 */ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		/* 0 */ "", "", "", "", "", "", "", "",
+		/* 8 */ "", "", "", "", "", "", "", "power-chassis-good";
+};
+
+&pinctrl {
+	key_pins: mux-keys {
+		groups = "gspi", "sspi";
+		function = "gpio";
+	};
+
+	led_pins: mux-leds {
+		groups = "hg3", "hg0", "pwm4";
+		function = "gpio";
+	};
+};
+
+&serial0 {
+	/*
+	 * Debug serial port. TX is exposed on the right pad of unpopulated
+	 * resistor R1247, RX on the right pad of R1162.
+	 */
+	status = "okay";
+};
+
+&serial1 {
+	/* "Serial over LAN" port. Connected to ttyS2 of the host system. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450.dtsi
new file mode 100644
index 000000000000..fd671c7a1e5d
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450.dtsi
@@ -0,0 +1,493 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+// Copyright 2021 Jonathan Neuschäfer
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "nuvoton,wpcm450";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+		gpio5 = &gpio5;
+		gpio6 = &gpio6;
+		gpio7 = &gpio7;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	clk24m: clock-24mhz {
+		/* 24 MHz dummy clock */
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+	refclk: clock-48mhz {
+		/* 48 MHz reference oscillator */
+		compatible = "fixed-clock";
+		clock-output-names = "ref";
+		clock-frequency = <48000000>;
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&aic>;
+		ranges;
+
+		gcr: syscon@b0000000 {
+			compatible = "nuvoton,wpcm450-gcr", "syscon", "simple-mfd";
+			reg = <0xb0000000 0x200>;
+		};
+
+		clk: clock-controller@b0000200 {
+			compatible = "nuvoton,wpcm450-clk";
+			reg = <0xb0000200 0x100>;
+			clocks = <&refclk>;
+			clock-names = "ref";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		serial0: serial@b8000000 {
+			compatible = "nuvoton,wpcm450-uart";
+			reg = <0xb8000000 0x20>;
+			reg-shift = <2>;
+			interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk24m>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&bsp_pins>;
+			status = "disabled";
+		};
+
+		serial1: serial@b8000100 {
+			compatible = "nuvoton,wpcm450-uart";
+			reg = <0xb8000100 0x20>;
+			reg-shift = <2>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk24m>;
+			status = "disabled";
+		};
+
+		timer0: timer@b8001000 {
+			compatible = "nuvoton,wpcm450-timer";
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0xb8001000 0x1c>;
+			clocks = <&clk24m>;
+		};
+
+		watchdog0: watchdog@b800101c {
+			compatible = "nuvoton,wpcm450-wdt";
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0xb800101c 0x4>;
+			clocks = <&clk24m>;
+		};
+
+		aic: interrupt-controller@b8002000 {
+			compatible = "nuvoton,wpcm450-aic";
+			reg = <0xb8002000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pinctrl: pinctrl@b8003000 {
+			compatible = "nuvoton,wpcm450-pinctrl";
+			reg = <0xb8003000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio0: gpio@0 {
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
+					     <3 IRQ_TYPE_LEVEL_HIGH>,
+					     <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+			};
+
+			gpio1: gpio@1 {
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+			};
+
+			gpio2: gpio@2 {
+				reg = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio3: gpio@3 {
+				reg = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio4: gpio@4 {
+				reg = <4>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio5: gpio@5 {
+				reg = <5>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio6: gpio@6 {
+				reg = <6>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio7: gpio@7 {
+				reg = <7>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			smb3_pins: mux-smb3 {
+				groups = "smb3";
+				function = "smb3";
+			};
+
+			smb4_pins: mux-smb4 {
+				groups = "smb4";
+				function = "smb4";
+			};
+
+			smb5_pins: mux-smb5 {
+				groups = "smb5";
+				function = "smb5";
+			};
+
+			scs1_pins: mux-scs1 {
+				groups = "scs1";
+				function = "scs1";
+			};
+
+			scs2_pins: mux-scs2 {
+				groups = "scs2";
+				function = "scs2";
+			};
+
+			scs3_pins: mux-scs3 {
+				groups = "scs3";
+				function = "scs3";
+			};
+
+			smb0_pins: mux-smb0 {
+				groups = "smb0";
+				function = "smb0";
+			};
+
+			smb1_pins: mux-smb1 {
+				groups = "smb1";
+				function = "smb1";
+			};
+
+			smb2_pins: mux-smb2 {
+				groups = "smb2";
+				function = "smb2";
+			};
+
+			bsp_pins: mux-bsp {
+				groups = "bsp";
+				function = "bsp";
+			};
+
+			hsp1_pins: mux-hsp1 {
+				groups = "hsp1";
+				function = "hsp1";
+			};
+
+			hsp2_pins: mux-hsp2 {
+				groups = "hsp2";
+				function = "hsp2";
+			};
+
+			r1err_pins: mux-r1err {
+				groups = "r1err";
+				function = "r1err";
+			};
+
+			r1md_pins: mux-r1md {
+				groups = "r1md";
+				function = "r1md";
+			};
+
+			rmii2_pins: mux-rmii2 {
+				groups = "rmii2";
+				function = "rmii2";
+			};
+
+			r2err_pins: mux-r2err {
+				groups = "r2err";
+				function = "r2err";
+			};
+
+			r2md_pins: mux-r2md {
+				groups = "r2md";
+				function = "r2md";
+			};
+
+			kbcc_pins: mux-kbcc {
+				groups = "kbcc";
+				function = "kbcc";
+			};
+
+			dvo0_pins: mux-dvo0 {
+				groups = "dvo";
+				function = "dvo0";
+			};
+
+			dvo3_pins: mux-dvo3 {
+				groups = "dvo";
+				function = "dvo3";
+			};
+
+			clko_pins: mux-clko {
+				groups = "clko";
+				function = "clko";
+			};
+
+			smi_pins: mux-smi {
+				groups = "smi";
+				function = "smi";
+			};
+
+			uinc_pins: mux-uinc {
+				groups = "uinc";
+				function = "uinc";
+			};
+
+			gspi_pins: mux-gspi {
+				groups = "gspi";
+				function = "gspi";
+			};
+
+			mben_pins: mux-mben {
+				groups = "mben";
+				function = "mben";
+			};
+
+			xcs2_pins: mux-xcs2 {
+				groups = "xcs2";
+				function = "xcs2";
+			};
+
+			xcs1_pins: mux-xcs1 {
+				groups = "xcs1";
+				function = "xcs1";
+			};
+
+			sdio_pins: mux-sdio {
+				groups = "sdio";
+				function = "sdio";
+			};
+
+			sspi_pins: mux-sspi {
+				groups = "sspi";
+				function = "sspi";
+			};
+
+			fi0_pins: mux-fi0 {
+				groups = "fi0";
+				function = "fi0";
+			};
+
+			fi1_pins: mux-fi1 {
+				groups = "fi1";
+				function = "fi1";
+			};
+
+			fi2_pins: mux-fi2 {
+				groups = "fi2";
+				function = "fi2";
+			};
+
+			fi3_pins: mux-fi3 {
+				groups = "fi3";
+				function = "fi3";
+			};
+
+			fi4_pins: mux-fi4 {
+				groups = "fi4";
+				function = "fi4";
+			};
+
+			fi5_pins: mux-fi5 {
+				groups = "fi5";
+				function = "fi5";
+			};
+
+			fi6_pins: mux-fi6 {
+				groups = "fi6";
+				function = "fi6";
+			};
+
+			fi7_pins: mux-fi7 {
+				groups = "fi7";
+				function = "fi7";
+			};
+
+			fi8_pins: mux-fi8 {
+				groups = "fi8";
+				function = "fi8";
+			};
+
+			fi9_pins: mux-fi9 {
+				groups = "fi9";
+				function = "fi9";
+			};
+
+			fi10_pins: mux-fi10 {
+				groups = "fi10";
+				function = "fi10";
+			};
+
+			fi11_pins: mux-fi11 {
+				groups = "fi11";
+				function = "fi11";
+			};
+
+			fi12_pins: mux-fi12 {
+				groups = "fi12";
+				function = "fi12";
+			};
+
+			fi13_pins: mux-fi13 {
+				groups = "fi13";
+				function = "fi13";
+			};
+
+			fi14_pins: mux-fi14 {
+				groups = "fi14";
+				function = "fi14";
+			};
+
+			fi15_pins: mux-fi15 {
+				groups = "fi15";
+				function = "fi15";
+			};
+
+			pwm0_pins: mux-pwm0 {
+				groups = "pwm0";
+				function = "pwm0";
+			};
+
+			pwm1_pins: mux-pwm1 {
+				groups = "pwm1";
+				function = "pwm1";
+			};
+
+			pwm2_pins: mux-pwm2 {
+				groups = "pwm2";
+				function = "pwm2";
+			};
+
+			pwm3_pins: mux-pwm3 {
+				groups = "pwm3";
+				function = "pwm3";
+			};
+
+			pwm4_pins: mux-pwm4 {
+				groups = "pwm4";
+				function = "pwm4";
+			};
+
+			pwm5_pins: mux-pwm5 {
+				groups = "pwm5";
+				function = "pwm5";
+			};
+
+			pwm6_pins: mux-pwm6 {
+				groups = "pwm6";
+				function = "pwm6";
+			};
+
+			pwm7_pins: mux-pwm7 {
+				groups = "pwm7";
+				function = "pwm7";
+			};
+
+			hg0_pins: mux-hg0 {
+				groups = "hg0";
+				function = "hg0";
+			};
+
+			hg1_pins: mux-hg1 {
+				groups = "hg1";
+				function = "hg1";
+			};
+
+			hg2_pins: mux-hg2 {
+				groups = "hg2";
+				function = "hg2";
+			};
+
+			hg3_pins: mux-hg3 {
+				groups = "hg3";
+				function = "hg3";
+			};
+
+			hg4_pins: mux-hg4 {
+				groups = "hg4";
+				function = "hg4";
+			};
+
+			hg5_pins: mux-hg5 {
+				groups = "hg5";
+				function = "hg5";
+			};
+
+			hg6_pins: mux-hg6 {
+				groups = "hg6";
+				function = "hg6";
+			};
+
+			hg7_pins: mux-hg7 {
+				groups = "hg7";
+				function = "hg7";
+			};
+		};
+
+		fiu: spi-controller@c8000000 {
+			compatible = "nuvoton,wpcm450-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xc8000000 0x1000>, <0xc0000000 0x4000000>;
+			reg-names = "control", "memory";
+			clocks = <&clk 0>;
+			nuvoton,shm = <&shm>;
+			status = "disabled";
+		};
+
+		shm: syscon@c8001000 {
+			compatible = "nuvoton,wpcm450-shm", "syscon";
+			reg = <0xc8001000 0x1000>;
+			reg-io-width = <1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/Makefile b/arch/arm/boot/dts/nvidia/Makefile
new file mode 100644
index 000000000000..60091bf7e48b
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/Makefile
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_TEGRA_114_SOC) += \
+	tegra114-asus-tf701t.dtb \
+	tegra114-dalmore.dtb \
+	tegra114-roth.dtb \
+	tegra114-tn7.dtb
+dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \
+	tegra124-apalis-eval.dtb \
+	tegra124-apalis-v1.2-eval.dtb \
+	tegra124-jetson-tk1.dtb \
+	tegra124-nyan-big.dtb \
+	tegra124-nyan-big-fhd.dtb \
+	tegra124-nyan-blaze.dtb \
+	tegra124-venice2.dtb
+dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
+	tegra20-acer-a500-picasso.dtb \
+	tegra20-asus-tf101.dtb \
+	tegra20-harmony.dtb \
+	tegra20-colibri-eval-v3.dtb \
+	tegra20-colibri-iris.dtb \
+	tegra20-medcom-wide.dtb \
+	tegra20-paz00.dtb \
+	tegra20-plutux.dtb \
+	tegra20-seaboard.dtb \
+	tegra20-tec.dtb \
+	tegra20-trimslice.dtb \
+	tegra20-ventana.dtb
+dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
+	tegra30-apalis-eval.dtb \
+	tegra30-apalis-v1.1-eval.dtb \
+	tegra30-asus-nexus7-grouper-PM269.dtb \
+	tegra30-asus-nexus7-grouper-E1565.dtb \
+	tegra30-asus-nexus7-tilapia-E1565.dtb \
+	tegra30-asus-tf201.dtb \
+	tegra30-asus-tf300t.dtb \
+	tegra30-asus-tf300tg.dtb \
+	tegra30-asus-tf700t.dtb \
+	tegra30-beaver.dtb \
+	tegra30-cardhu-a02.dtb \
+	tegra30-cardhu-a04.dtb \
+	tegra30-colibri-eval-v3.dtb \
+	tegra30-ouya.dtb \
+	tegra30-pegatron-chagall.dtb
diff --git a/arch/arm/boot/dts/nvidia/tegra114-asus-tf701t.dts b/arch/arm/boot/dts/nvidia/tegra114-asus-tf701t.dts
new file mode 100644
index 000000000000..763ab812eb87
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra114-asus-tf701t.dts
@@ -0,0 +1,809 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+
+#include "tegra114.dtsi"
+
+/ {
+	model = "Asus Transformer Pad TF701T";
+	compatible = "asus,tf701t", "nvidia,tegra114";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = "/mmc@78000600"; /* eMMC */
+		mmc1 = "/mmc@78000400"; /* uSD slot */
+		mmc2 = "/mmc@78000000"; /* WiFi */
+
+		rtc0 = &palmas;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd; /* Console */
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;
+			linux,cma-default;
+			reusable;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		dsi@54300000 {
+			status = "okay";
+
+			avdd-dsi-csi-supply = <&tps65913_ldo2>;
+
+			nvidia,ganged-mode = <&dsib>;
+
+			panel_primary: panel@0 {
+				compatible = "sharp,lq101r1sx01";
+				reg = <0>;
+
+				link2 = <&panel_secondary>;
+
+				power-supply = <&vdd_lcd>;
+				backlight = <&backlight>;
+			};
+		};
+
+		dsi@54400000 {
+			status = "okay";
+
+			avdd-dsi-csi-supply = <&tps65913_ldo2>;
+
+			panel_secondary: panel@0 {
+				compatible = "sharp,lq101r1sx01";
+				reg = <0>;
+			};
+		};
+	};
+
+	pinmux@70000868 {
+		asus_pad_ec_default: pinmux-asus-pad-ec-default {
+			ec-interrupt {
+				nvidia,pins = "kb_col5_pq5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ec-request {
+				nvidia,pins = "kb_col2_pq2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		backlight_default: pinmux-backlight-default {
+			backlight-enable {
+				nvidia,pins = "gmi_ad10_ph2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		codec_default: pinmux-codec-default {
+			interrupt {
+				nvidia,pins = "gpio_w2_aud_pw2",
+						"gpio_w3_aud_pw3";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ldo1-en {
+				nvidia,pins = "sdmmc1_wp_n_pv3";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		gpio_hall_sensor_default: pinmux-gpio-hall-sensor-default {
+			ulpi_data4_po5 {
+				nvidia,pins = "ulpi_data4_po5";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		gpio_keys_default: pinmux-gpio-keys-default {
+			power {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			volume {
+				nvidia,pins = "kb_row1_pr1",
+						"kb_row2_pr2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		hp_det_default: pinmux-hp-det-default {
+			gmi_iordy_pi5 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		imu_default: pinmux-imu-default {
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		pwm_default: pinmux-pwm-default {
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		/* XXX make this something more sensible */
+		pwm_sleep: pinmux-pwm-sleep {
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		sdmmc3_default: pinmux-sdmmc3-default {
+			drive_sdio3 {
+				nvidia,pins = "drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_ENABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <22>;
+				nvidia,pull-up-strength = <36>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat3_pb4",
+						"kb_col4_pq4",
+						"sdmmc3_clk_lb_out_pee4",
+						"sdmmc3_clk_lb_in_pee5",
+						"sdmmc3_cd_n_pv2";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		sdmmc3_vdd_default: pinmux-sdmmc3-vdd-default {
+			gmi_clk_pk1 {
+				nvidia,pins = "gmi_clk_pk1";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		vdd_lcd_default: pinmux-vdd-lcd-default {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	serial@70006040 {
+		/* GPS */
+	};
+
+	serial@70006200 {
+		/* Bluetooth */
+	};
+
+	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+		status = "okay";
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm_default>;
+		pinctrl-1 = <&pwm_sleep>;
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		magnetometer@c {
+			compatible = "asahi-kasei,ak09911";
+			reg = <0xc>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+
+		rt5639: audio-codec@1c {
+			compatible = "realtek,rt5639";
+			reg = <0x1c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
+
+			realtek,ldo1-en-gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&codec_default>;
+		};
+
+		temp_sensor: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		motion-tracker@68 {
+			compatible = "invensense,mpu6500";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(R, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			mount-matrix =  "0", "-1", "0",
+					"1",  "0", "0",
+					"0",  "0", "1";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&imu_default>;
+		};
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		power-sensor@44 {
+			compatible = "ti,ina230";
+			reg = <0x44>;
+		};
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		light-sensor@1c {
+			compatible = "dynaimage,al3320a";
+			reg = <0x1c>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+	};
+
+	i2c@7000c700 {
+		/* HDMI DDC */
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		palmas: pmic@58 {
+			compatible = "ti,tps65913", "ti,palmas";
+			reg = <0x58>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			ti,system-power-controller;
+
+			palmas_gpio: gpio {
+				compatible = "ti,palmas-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			pinmux {
+				compatible = "ti,tps65913-pinctrl";
+				ti,palmas-enable-dvfs1;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&palmas_default>;
+
+				palmas_default: pinmux {
+					pin_gpio0 {
+						pins = "gpio0";
+						function = "gpio";
+					};
+
+					pin_gpio1 {
+						pins = "gpio1";
+						function = "gpio";
+					};
+
+					pin_gpio2 {
+						pins = "gpio2";
+						function = "gpio";
+					};
+
+					pin_gpio3 {
+						pins = "gpio3";
+						function = "gpio";
+					};
+
+					pin_gpio4 {
+						pins = "gpio4";
+						function = "gpio";
+					};
+
+					pin_gpio5 {
+						pins = "gpio5";
+						function = "gpio";
+					};
+
+					pin_gpio6 {
+						pins = "gpio6";
+						function = "gpio";
+					};
+
+					pin_gpio7 {
+						pins = "gpio7";
+						function = "gpio";
+					};
+
+					pin_powergood {
+						pins = "powergood";
+						function = "powergood";
+					};
+
+					pin_vac {
+						pins = "vac";
+						function = "vac";
+					};
+				};
+			};
+
+			pmic {
+				compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+
+				ldo1-in-supply = <&tps65913_smps7>;
+				ldo2-in-supply = <&tps65913_smps7>;
+				ldo4-in-supply = <&tps65913_smps8>;
+				ldo5-in-supply = <&tps65913_smps9>;
+				ldo6-in-supply = <&tps65913_smps9>;
+				ldo7-in-supply = <&tps65913_smps9>;
+				ldo9-in-supply = <&tps65913_smps9>;
+
+				regulators {
+					tps65913_smps123: smps123 {
+						regulator-name = "vdd-cpu";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <1>;
+						ti,mode-sleep = <3>;
+					};
+
+					tps65913_smps45: smps45 {
+						regulator-name = "vdd-core";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1400000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <3>;
+					};
+
+					smps6 {
+						regulator-name = "va-lcd-hv";
+						regulator-min-microvolt = <1000000>;
+						regulator-max-microvolt = <1000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps7: smps7 {
+						regulator-name = "vdd-ddr";
+						regulator-min-microvolt = <1350000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps8: smps8 {
+						regulator-name = "vdd-1v8";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps9: smps9 {
+						regulator-name = "vdd-sd";
+						regulator-min-microvolt = <2900000>;
+						regulator-max-microvolt = <2900000>;
+						regulator-always-on;
+					};
+
+					tps65913_smps10_out1: smps10_out1 {
+						regulator-name = "vd-smps10-out1";
+						regulator-min-microvolt = <5000000>;
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps10_out2: smps10_out2 {
+						regulator-name = "vd-smps10-out2";
+						regulator-min-microvolt = <5000000>;
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_ldo1: ldo1 {
+						regulator-name = "vdd-hdmi-pll";
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <1050000>;
+						regulator-always-on;
+						ti,roof-floor = <3>;
+					};
+
+					tps65913_ldo2: ldo2 {
+						regulator-name = "vdd-2v8-dsi-csi";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+						regulator-boot-on;
+					};
+
+					ldo3 {
+						regulator-name = "vpp-fuse";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ldo4 {
+						regulator-name = "vdd-1v2-cam";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+					};
+
+					ldo5 {
+						regulator-name = "vdd-cam";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					ldo6 {
+						regulator-name = "vdd-dev";
+						regulator-min-microvolt = <2850000>;
+						regulator-max-microvolt = <2850000>;
+						regulator-boot-on;
+					};
+
+					ldo7 {
+						regulator-name = "vdd-2v8-cam";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					tps65913_ldo8: ldo8 {
+						regulator-name = "vdd-rtc";
+						regulator-min-microvolt = <950000>;
+						regulator-max-microvolt = <950000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,enable-ldo8-tracking;
+					};
+
+					tps65913_ldo9: ldo9 {
+						regulator-name = "vdd-sdmmc";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <2900000>;
+					};
+
+					tps65913_ldoln: ldoln {
+						regulator-name = "vdd-hdmi";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ldousb {
+						regulator-name = "vdd-usb";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+				};
+			};
+
+			rtc {
+				compatible = "ti,palmas-rtc";
+				interrupt-parent = <&palmas>;
+				interrupts = <8 0>;
+			};
+		};
+	};
+
+	ahub@70080000 {
+		i2s@70080300 {
+			status = "okay";
+		};
+	};
+
+	mmc@78000000 {
+		/* WiFi */
+	};
+
+	/* MicroSD card */
+	mmc@78000400 {
+		status = "okay";
+
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+
+		nvidia,default-tap = <0x3>;
+		nvidia,default-trim = <0x3>;
+
+		vmmc-supply = <&vdd_usd>;
+		vqmmc-supply = <&tps65913_ldo9>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc3_default>;
+	};
+
+	mmc@78000600 {
+		/* eMMC */
+	};
+
+	usb@7d000000 {
+		compatible = "nvidia,tegra114-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+
+		/* Peripheral USB via ASUS connector */
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+	};
+
+	usb@7d008000 {
+		status = "okay";
+
+		/* Host USB via dock */
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_sys>;
+		pwms = <&pwm 1 1000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <224>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_default>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		label = "GPIO Hall Effect Sensor";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_hall_sensor_default>;
+
+		switch-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		label = "GPIO Buttons";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		button-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		button-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+		};
+
+		button-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+		};
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5639-tf701t",
+			     "nvidia,tegra-audio-rt5640";
+		nvidia,model = "Asus Transformer Pad TF701T RT5639";
+
+		nvidia,audio-routing =
+			"Headphones", "HPOR",
+			"Headphones", "HPOL",
+			"Speakers", "SPORP",
+			"Speakers", "SPORN",
+			"Speakers", "SPOLP",
+			"Speakers", "SPOLN",
+			"Mic Jack", "MICBIAS1",
+			"IN2P", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s0>;
+		nvidia,audio-codec = <&rt5639>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_LOW>;
+
+		clocks = <&tegra_car TEGRA114_CLK_PLL_A>,
+			 <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA114_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA114_CLK_EXTERN1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_det_default>;
+	};
+
+	vdd_5v0_sys: regulator-5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_lcd: regulator-vdd-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_lcd_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&tps65913_smps8>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(CC, 4) GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_lcd_default>;
+	};
+
+	vdd_usd: regulator-vdd-usd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sd_slot";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		vin-supply = <&tps65913_smps9>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc3_vdd_default>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/nvidia/tegra114-dalmore.dts
index 97a5c3504bbe..c06b52fe330a 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/nvidia/tegra114-dalmore.dts
@@ -46,8 +46,7 @@
 			avdd-dsi-csi-supply = <&avdd_1v2_reg>;
 
 			panel@0 {
-				compatible = "panasonic,vvx10f004b00",
-					     "simple-panel";
+				compatible = "panasonic,vvx10f004b00";
 				reg = <0>;
 
 				power-supply = <&avdd_lcd_reg>;
@@ -756,6 +755,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -770,7 +771,6 @@
 		battery: smart-battery@b {
 			compatible = "ti,bq20z45", "sbs,sbs-battery";
 			reg = <0xb>;
-			battery-name = "battery";
 			sbs,i2c-retry-count = <2>;
 			sbs,poll-retry-count = <100>;
 			power-supplies = <&charger>;
@@ -790,7 +790,7 @@
 			reg = <0x4c>;
 			vcc-supply = <&palmas_ldo6_reg>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_EDGE_FALLING>;
 		};
 	};
 
@@ -896,7 +896,7 @@
 		};
 
 		palmas: tps65913@58 {
-			compatible = "ti,palmas";
+			compatible = "ti,tps65913", "ti,palmas";
 			reg = <0x58>;
 			interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -911,6 +911,19 @@
 				#gpio-cells = <2>;
 			};
 
+			pinmux {
+				compatible = "ti,tps65913-pinctrl";
+				pinctrl-names = "default";
+				pinctrl-0 = <&palmas_default>;
+
+				palmas_default: pinmux {
+					pin_gpio6 {
+						pins = "gpio6";
+						function = "gpio";
+					};
+				};
+			};
+
 			pmic {
 				compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
 				smps1-in-supply = <&tps65090_dcdc3_reg>;
@@ -1067,26 +1080,14 @@
 				interrupt-parent = <&palmas>;
 				interrupts = <8 0>;
 			};
-
-			pinmux {
-				compatible = "ti,tps65913-pinctrl";
-				pinctrl-names = "default";
-				pinctrl-0 = <&palmas_default>;
-
-				palmas_default: pinmux {
-					pin_gpio6 {
-						pins = "gpio6";
-						function = "gpio";
-					};
-				};
-			};
 		};
 	};
 
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q32dw", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <20000000>;
@@ -1110,14 +1111,14 @@
 		};
 	};
 
-	sdhci@78000400 {
+	mmc@78000400 {
 		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
 		bus-width = <4>;
 		status = "okay";
 	};
 
-	sdhci@78000600 {
+	mmc@78000600 {
 		bus-width = <8>;
 		status = "okay";
 		non-removable;
@@ -1153,125 +1154,105 @@
 		default-brightness-level = <6>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_ac_bat_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd_ac_bat";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_ac_bat_reg: regulator-acbat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ac_bat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		dvdd_ts_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "dvdd_ts";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
-		};
+	dvdd_ts_reg: regulator-ts {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd_ts";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+	};
 
-		usb1_vbus_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&tps65090_dcdc1_reg>;
-		};
+	usb1_vbus_reg: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&tps65090_dcdc1_reg>;
+	};
 
-		usb3_vbus_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "usb2_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&tps65090_dcdc1_reg>;
-		};
+	usb3_vbus_reg: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&tps65090_dcdc1_reg>;
+	};
 
-		vdd_hdmi_reg: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "vdd_hdmi_5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			vin-supply = <&tps65090_dcdc1_reg>;
-		};
+	vdd_hdmi_reg: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_hdmi_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&tps65090_dcdc1_reg>;
+	};
 
-		vdd_cam_1v8_reg: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "vdd_cam_1v8_reg";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			enable-active-high;
-			gpio = <&palmas_gpio 6 0>;
-		};
+	vdd_cam_1v8_reg: regulator-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_cam_1v8_reg";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		gpio = <&palmas_gpio 6 0>;
+	};
 
-		vdd_5v0_hdmi: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "VDD_5V0_HDMI_CON";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&tps65090_dcdc1_reg>;
-		};
+	vdd_5v0_hdmi: regulator-hdmicon {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_5V0_HDMI_CON";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&tps65090_dcdc1_reg>;
 	};
 
 	sound {
@@ -1296,7 +1277,13 @@
 
 		clocks = <&tegra_car TEGRA114_CLK_PLL_A>,
 			 <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA114_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA114_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA114_CLK_EXTERN1>;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra114-roth.dts b/arch/arm/boot/dts/nvidia/tegra114-roth.dts
index 3d3835591cd2..a89b16573b42 100644
--- a/arch/arm/boot/dts/tegra114-roth.dts
+++ b/arch/arm/boot/dts/nvidia/tegra114-roth.dts
@@ -37,7 +37,7 @@
 		dsi@54300000 {
 			status = "okay";
 
-			vdd-supply = <&vdd_1v2_ap>;
+			avdd-dsi-csi-supply = <&vdd_1v2_ap>;
 
 			panel@0 {
 				compatible = "lg,lh500wx1-sd03";
@@ -779,6 +779,8 @@
 
 	/* Usable on reworked devices only */
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -801,7 +803,7 @@
 		};
 
 		palmas: pmic@58 {
-			compatible = "ti,palmas";
+			compatible = "ti,tps65913", "ti,palmas";
 			reg = <0x58>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -962,7 +964,7 @@
 	};
 
 	/* SD card */
-	sdhci@78000400 {
+	mmc@78000400 {
 		status = "okay";
 		bus-width = <4>;
 		vqmmc-supply = <&vddio_sdmmc3>;
@@ -971,7 +973,7 @@
 	};
 
 	/* eMMC */
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1016,35 +1018,28 @@
 		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1052,76 +1047,64 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		lcd_bl_en: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "lcd_bl_en";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-boot-on;
-		};
+	lcd_bl_en: regulator-lcden {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd_bl_en";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
 
-		vdd_lcd: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vdd_lcd_1v8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			vin-supply = <&vdd_1v8>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
-			regulator-boot-on;
-		};
+	vdd_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_lcd_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vdd_1v8>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+	};
 
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vdd_1v8_ts";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			gpio = <&gpio TEGRA_GPIO(K, 3) GPIO_ACTIVE_LOW>;
-			regulator-boot-on;
-		};
+	regulator-1v8ts {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_ts";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio TEGRA_GPIO(K, 3) GPIO_ACTIVE_LOW>;
+		regulator-boot-on;
+	};
 
-		regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vdd_3v3_ts";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
-			regulator-boot-on;
-		};
+	regulator-3v3ts {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_ts";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+	};
 
-		regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "vdd_1v8_com";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			vin-supply = <&vdd_1v8>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
-			regulator-boot-on;
-		};
+	regulator-1v8com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_com";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vdd_1v8>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+	};
 
-		regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "vdd_3v3_com";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vdd_3v3_sys>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
+	regulator-3v3com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vdd_3v3_sys>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra114-tn7.dts b/arch/arm/boot/dts/nvidia/tegra114-tn7.dts
index bfdd1bf61816..bfbdb345575a 100644
--- a/arch/arm/boot/dts/tegra114-tn7.dts
+++ b/arch/arm/boot/dts/nvidia/tegra114-tn7.dts
@@ -37,7 +37,7 @@
 		dsi@54300000 {
 			status = "okay";
 
-			vdd-supply = <&vdd_1v2_ap>;
+			avdd-dsi-csi-supply = <&vdd_1v2_ap>;
 
 			panel@0 {
 				compatible = "lg,ld070wx3-sl01";
@@ -50,6 +50,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -62,7 +64,7 @@
 		clock-frequency = <400000>;
 
 		palmas: pmic@58 {
-			compatible = "ti,palmas";
+			compatible = "ti,tps65913", "ti,palmas";
 			reg = <0x58>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -242,7 +244,7 @@
 	};
 
 	/* eMMC */
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -273,80 +275,64 @@
 		power-supply = <&lcd_bl_en>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* FIXME: output of BQ24192 */
-		vs_sys: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "VS_SYS";
-			regulator-min-microvolt = <4200000>;
-			regulator-max-microvolt = <4200000>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
+	/* FIXME: output of BQ24192 */
+	vs_sys: regulator-vs {
+		compatible = "regulator-fixed";
+		regulator-name = "VS_SYS";
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 
-		lcd_bl_en: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "VDD_LCD_BL";
-			regulator-min-microvolt = <16500000>;
-			regulator-max-microvolt = <16500000>;
-			gpio = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vs_sys>;
-			regulator-boot-on;
-		};
+	lcd_bl_en: regulator-lcden {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_LCD_BL";
+		regulator-min-microvolt = <16500000>;
+		regulator-max-microvolt = <16500000>;
+		gpio = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vs_sys>;
+		regulator-boot-on;
+	};
 
-		vdd_lcd: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "VD_LCD_1V8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			gpio = <&palmas_gpio 4 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_1v8>;
-			regulator-boot-on;
-		};
+	vdd_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "VD_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&palmas_gpio 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_1v8>;
+		regulator-boot-on;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra114.dtsi b/arch/arm/boot/dts/nvidia/tegra114.dtsi
index 0d7a6327e404..86f14e2fd29f 100644
--- a/arch/arm/boot/dts/tegra114.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra114.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/memory/tegra114-mc.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/tegra-pmc.h>
 
 / {
 	compatible = "nvidia,tegra114";
@@ -16,14 +17,29 @@
 		reg = <0x80000000 0x0>;
 	};
 
+	sram@40000000 {
+		compatible = "mmio-sram";
+		reg = <0x40000000 0x40000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x40000000 0x40000>;
+
+		vde_pool: sram@400 {
+			reg = <0x400 0x3fc00>;
+			pool;
+		};
+	};
+
 	host1x@50000000 {
-		compatible = "nvidia,tegra114-host1x", "simple-bus";
+		compatible = "nvidia,tegra114-host1x";
 		reg = <0x50000000 0x00028000>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */
 			     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */
+		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA114_CLK_HOST1X>;
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		clock-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA114_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 		iommus = <&mc TEGRA_SWGROUP_HC>;
 
 		#address-cells = <1>;
@@ -32,28 +48,28 @@
 		ranges = <0x54000000 0x54000000 0x01000000>;
 
 		gr2d@54140000 {
-			compatible = "nvidia,tegra114-gr2d", "nvidia,tegra20-gr2d";
+			compatible = "nvidia,tegra114-gr2d";
 			reg = <0x54140000 0x00040000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA114_CLK_GR2D>;
-			resets = <&tegra_car 21>;
-			reset-names = "2d";
+			resets = <&tegra_car 21>, <&mc TEGRA114_MC_RESET_2D>;
+			reset-names = "2d", "mc";
 
 			iommus = <&mc TEGRA_SWGROUP_G2>;
 		};
 
 		gr3d@54180000 {
-			compatible = "nvidia,tegra114-gr3d", "nvidia,tegra20-gr3d";
+			compatible = "nvidia,tegra114-gr3d";
 			reg = <0x54180000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_GR3D>;
-			resets = <&tegra_car 24>;
-			reset-names = "3d";
+			resets = <&tegra_car 24>, <&mc TEGRA114_MC_RESET_3D>;
+			reset-names = "3d", "mc";
 
 			iommus = <&mc TEGRA_SWGROUP_NV>;
 		};
 
 		dc@54200000 {
-			compatible = "nvidia,tegra114-dc", "nvidia,tegra20-dc";
+			compatible = "nvidia,tegra114-dc";
 			reg = <0x54200000 0x00040000>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA114_CLK_DISP1>,
@@ -72,7 +88,7 @@
 		};
 
 		dc@54240000 {
-			compatible = "nvidia,tegra114-dc", "nvidia,tegra20-dc";
+			compatible = "nvidia,tegra114-dc";
 			reg = <0x54240000 0x00040000>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA114_CLK_DISP2>,
@@ -102,7 +118,7 @@
 			status = "disabled";
 		};
 
-		dsi@54300000 {
+		dsia: dsi@54300000 {
 			compatible = "nvidia,tegra114-dsi";
 			reg = <0x54300000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_DSIA>,
@@ -118,7 +134,7 @@
 			#size-cells = <0>;
 		};
 
-		dsi@54400000 {
+		dsib: dsi@54400000 {
 			compatible = "nvidia,tegra114-dsi";
 			reg = <0x54400000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_DSIB>,
@@ -161,7 +177,7 @@
 	};
 
 	timer@60005000 {
-		compatible = "nvidia,tegra114-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+		compatible = "nvidia,tegra114-timer", "nvidia,tegra30-timer";
 		reg = <0x60005000 0x400>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
@@ -245,21 +261,43 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 246>;
-		*/
+	};
+
+	vde@6001a000 {
+		compatible = "nvidia,tegra114-vde";
+		reg = <0x6001a000 0x1000>, /* Syntax Engine */
+		      <0x6001b000 0x1000>, /* Video Bitstream Engine */
+		      <0x6001c000  0x100>, /* Macroblock Engine */
+		      <0x6001c200  0x100>, /* Post-processing Engine */
+		      <0x6001c400  0x100>, /* Motion Compensation Engine */
+		      <0x6001c600  0x100>, /* Transform Engine */
+		      <0x6001c800  0x100>, /* Pixel prediction block */
+		      <0x6001ca00  0x100>, /* Video DMA */
+		      <0x6001d800  0x400>; /* Video frame controls */
+		reg-names = "sxe", "bsev", "mbe", "ppe", "mce",
+			    "tfe", "ppb", "vdma", "frameid";
+		iram = <&vde_pool>; /* IRAM region */
+		interrupts = <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>, /* Sync token interrupt */
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, /* BSE-V interrupt */
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; /* SXE interrupt */
+		interrupt-names = "sync-token", "bsev", "sxe";
+		clocks = <&tegra_car TEGRA114_CLK_VDE>;
+		reset-names = "vde", "mc";
+		resets = <&tegra_car 61>, <&mc TEGRA114_MC_RESET_VDE>;
+		iommus = <&mc TEGRA_SWGROUP_VDE>;
 	};
 
 	apbmisc@70000800 {
 		compatible = "nvidia,tegra114-apbmisc", "nvidia,tegra20-apbmisc";
-		reg = <0x70000800 0x64   /* Chip revision */
-		       0x70000008 0x04>; /* Strapping options */
+		reg = <0x70000800 0x64>, /* Chip revision */
+		      <0x70000008 0x04>; /* Strapping options */
 	};
 
 	pinmux: pinmux@70000868 {
 		compatible = "nvidia,tegra114-pinmux";
-		reg = <0x70000868 0x148		/* Pad control registers */
-		       0x70003000 0x40c>;	/* Mux registers */
+		reg = <0x70000868 0x148>, /* Pad control registers */
+		      <0x70003000 0x40c>; /* Mux registers */
 	};
 
 	/*
@@ -277,7 +315,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -290,7 +327,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -303,7 +339,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -316,7 +351,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -514,11 +548,12 @@
 		status = "disabled";
 	};
 
-	pmc@7000e400 {
+	tegra_pmc: pmc@7000e400 {
 		compatible = "nvidia,tegra114-pmc";
 		reg = <0x7000e400 0x400>;
 		clocks = <&tegra_car TEGRA114_CLK_PCLK>, <&clk32k_in>;
 		clock-names = "pclk", "clk32k_in";
+		#clock-cells = <1>;
 	};
 
 	fuse@7000f800 {
@@ -538,6 +573,7 @@
 
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 
+		#reset-cells = <1>;
 		#iommu-cells = <1>;
 	};
 
@@ -642,48 +678,52 @@
 		#nvidia,mipi-calibrate-cells = <1>;
 	};
 
-	sdhci@78000000 {
-		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+	mmc@78000000 {
+		compatible = "nvidia,tegra114-sdhci";
 		reg = <0x78000000 0x200>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_SDMMC1>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 14>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@78000200 {
-		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+	mmc@78000200 {
+		compatible = "nvidia,tegra114-sdhci";
 		reg = <0x78000200 0x200>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_SDMMC2>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 9>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@78000400 {
-		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+	mmc@78000400 {
+		compatible = "nvidia,tegra114-sdhci";
 		reg = <0x78000400 0x200>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_SDMMC3>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 69>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@78000600 {
-		compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+	mmc@78000600 {
+		compatible = "nvidia,tegra114-sdhci";
 		reg = <0x78000600 0x200>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_SDMMC4>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 15>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
 	usb@7d000000 {
-		compatible = "nvidia,tegra114-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra114-ehci", "nvidia,tegra30-ehci";
 		reg = <0x7d000000 0x4000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -696,7 +736,9 @@
 
 	phy1: usb-phy@7d000000 {
 		compatible = "nvidia,tegra114-usb-phy", "nvidia,tegra30-usb-phy";
-		reg = <0x7d000000 0x4000 0x7d000000 0x4000>;
+		reg = <0x7d000000 0x4000>,
+		      <0x7d000000 0x4000>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA114_CLK_USBD>,
 			 <&tegra_car TEGRA114_CLK_PLL_U>,
@@ -704,6 +746,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 22>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -715,11 +758,12 @@
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
 		nvidia,has-utmi-pad-registers;
+		nvidia,pmc = <&tegra_pmc 0>;
 		status = "disabled";
 	};
 
 	usb@7d008000 {
-		compatible = "nvidia,tegra114-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra114-ehci", "nvidia,tegra30-ehci";
 		reg = <0x7d008000 0x4000>;
 		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -732,7 +776,9 @@
 
 	phy3: usb-phy@7d008000 {
 		compatible = "nvidia,tegra114-usb-phy", "nvidia,tegra30-usb-phy";
-		reg = <0x7d008000 0x4000 0x7d000000 0x4000>;
+		reg = <0x7d008000 0x4000>,
+		      <0x7d000000 0x4000>;
+		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA114_CLK_USB3>,
 			 <&tegra_car TEGRA114_CLK_PLL_U>,
@@ -740,6 +786,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 59>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -750,6 +797,7 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,pmc = <&tegra_pmc 2>;
 		status = "disabled";
 	};
 
diff --git a/arch/arm/boot/dts/tegra124-apalis-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-apalis-emc.dtsi
index d18eaf4a4a3a..970f33dd9101 100644
--- a/arch/arm/boot/dts/tegra124-apalis-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-emc.dtsi
@@ -4,6 +4,8 @@
  *
  */
 
+#include <dt-bindings/clock/tegra124-car.h>
+
 / {
 	clock@60006000 {
 		emc-timings-1 {
@@ -15,66 +17,77 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-924000000 {
 				clock-frequency = <924000000>;
 				nvidia,parent-clock-frequency = <924000000>;
@@ -84,7 +97,217 @@
 		};
 	};
 
-	emc@7001b000 {
+	memory-controller@70019000 {
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 0x8000000a
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x77e30303 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 0x80000012
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x76230303 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 0x80000017
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x74a30303 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 0x8000001e
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x74230403 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 0x80000026
+					0x00000001 0x00000001
+					0x00000003 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0503
+					0x73c30504 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 0x80000040
+					0x00000001 0x00000001
+					0x00000004 0x00000002
+					0x00000003 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000004 0x00000006
+					0x06040203 0x000a0504
+					0x73840a05 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 0x80000040
+					0x00000001 0x00000002
+					0x00000007 0x00000004
+					0x00000004 0x00000001
+					0x00000002 0x00000007
+					0x00000002 0x00000002
+					0x00000004 0x00000006
+					0x06040202 0x000b0607
+					0x77450e08 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 0x80000040
+					0x00000001 0x00000002
+					0x00000009 0x00000005
+					0x00000006 0x00000001
+					0x00000002 0x00000008
+					0x00000002 0x00000002
+					0x00000004 0x00000006
+					0x06040202 0x000d0709
+					0x7586120a 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 0x80000040
+					0x00000002 0x00000003
+					0x0000000c 0x00000007
+					0x00000008 0x00000001
+					0x00000002 0x00000009
+					0x00000002 0x00000002
+					0x00000005 0x00000006
+					0x06050202 0x0010090c
+					0x7428180d 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 0x80000040
+					0x00000003 0x00000004
+					0x0000000e 0x00000009
+					0x0000000a 0x00000001
+					0x00000003 0x0000000b
+					0x00000002 0x00000002
+					0x00000005 0x00000007
+					0x07050202 0x00130b0e
+					0x73a91b0f 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b 0x80000040
+					0x00000004 0x00000005
+					0x00000013 0x0000000c
+					0x0000000d 0x00000002
+					0x00000003 0x0000000c
+					0x00000002 0x00000002
+					0x00000006 0x00000008
+					0x08060202 0x00170e13
+					0x736c2414 0x70000f02
+					0x001f0000
+				>;
+			};
+
+			timing-924000000 {
+				clock-frequency = <924000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000d 0x80000040
+					0x00000005 0x00000006
+					0x00000016 0x0000000e
+					0x0000000f 0x00000002
+					0x00000004 0x0000000e
+					0x00000002 0x00000002
+					0x00000006 0x00000009
+					0x09060202 0x001a1016
+					0x734e2a17 0x70000f02
+					0x001f0000
+				>;
+			};
+		};
+	};
+
+	external-memory-controller@7001b000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
 
@@ -1251,217 +1474,14 @@
 					0x00000011
 				>;
 			};
-
 		};
 	};
 
-	memory-controller@70019000 {
-		emc-timings-1 {
-			nvidia,ram-code = <1>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 0x8000000a
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x77e30303 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 0x80000012
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x76230303 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 0x80000017
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x74a30303 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 0x8000001e
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x74230403 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 0x80000026
-					0x00000001 0x00000001
-					0x00000003 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0503
-					0x73c30504 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 0x80000040
-					0x00000001 0x00000001
-					0x00000004 0x00000002
-					0x00000003 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000004 0x00000006
-					0x06040203 0x000a0504
-					0x73840a05 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 0x80000040
-					0x00000001 0x00000002
-					0x00000007 0x00000004
-					0x00000004 0x00000001
-					0x00000002 0x00000007
-					0x00000002 0x00000002
-					0x00000004 0x00000006
-					0x06040202 0x000b0607
-					0x77450e08 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 0x80000040
-					0x00000001 0x00000002
-					0x00000009 0x00000005
-					0x00000006 0x00000001
-					0x00000002 0x00000008
-					0x00000002 0x00000002
-					0x00000004 0x00000006
-					0x06040202 0x000d0709
-					0x7586120a 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 0x80000040
-					0x00000002 0x00000003
-					0x0000000c 0x00000007
-					0x00000008 0x00000001
-					0x00000002 0x00000009
-					0x00000002 0x00000002
-					0x00000005 0x00000006
-					0x06050202 0x0010090c
-					0x7428180d 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 0x80000040
-					0x00000003 0x00000004
-					0x0000000e 0x00000009
-					0x0000000a 0x00000001
-					0x00000003 0x0000000b
-					0x00000002 0x00000002
-					0x00000005 0x00000007
-					0x07050202 0x00130b0e
-					0x73a91b0f 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b 0x80000040
-					0x00000004 0x00000005
-					0x00000013 0x0000000c
-					0x0000000d 0x00000002
-					0x00000003 0x0000000c
-					0x00000002 0x00000002
-					0x00000006 0x00000008
-					0x08060202 0x00170e13
-					0x736c2414 0x70000f02
-					0x001f0000
-				>;
-			};
-
-			timing-924000000 {
-				clock-frequency = <924000000>;
+	opp-table-actmon {
+		/delete-node/ opp-1200000000;
+	};
 
-				nvidia,emem-configuration = <
-					0x0e00000d 0x80000040
-					0x00000005 0x00000006
-					0x00000016 0x0000000e
-					0x0000000f 0x00000002
-					0x00000004 0x0000000e
-					0x00000002 0x00000002
-					0x00000006 0x00000009
-					0x09060202 0x001a1016
-					0x734e2a17 0x70000f02
-					0x001f0000
-				>;
-			};
-		};
+	opp-table-emc {
+		/delete-node/ opp-1200000000-1100;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra124-apalis-eval.dts b/arch/arm/boot/dts/nvidia/tegra124-apalis-eval.dts
index ceb3f6388c7d..0f3debeb294b 100644
--- a/arch/arm/boot/dts/tegra124-apalis-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-eval.dts
@@ -40,8 +40,20 @@
 		};
 	};
 
+	gpio: gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -130,7 +142,7 @@
 	};
 
 	/* Apalis MMC1 */
-	sdhci@700b0000 {
+	mmc@700b0000 {
 		status = "okay";
 		bus-width = <4>;
 		/* MMC1_CD# */
@@ -139,7 +151,7 @@
 	};
 
 	/* Apalis SD1 */
-	sdhci@700b0400 {
+	mmc@700b0400 {
 		status = "okay";
 		bus-width = <4>;
 		/* SD1_CD# */
@@ -191,7 +203,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -243,13 +255,3 @@
 		vin-supply = <&reg_5v0>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2-eval.dts
index 826b776fbe6f..d13b8d25ca6a 100644
--- a/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2-eval.dts
@@ -41,8 +41,20 @@
 		};
 	};
 
+	gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -132,7 +144,7 @@
 	};
 
 	/* Apalis MMC1 */
-	sdhci@700b0000 {
+	mmc@700b0000 {
 		status = "okay";
 		bus-width = <4>;
 		/* MMC1_CD# */
@@ -141,7 +153,7 @@
 	};
 
 	/* Apalis SD1 */
-	sdhci@700b0400 {
+	mmc@700b0400 {
 		status = "okay";
 		bus-width = <4>;
 		/* SD1_CD# */
@@ -193,7 +205,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -245,13 +257,3 @@
 		vin-supply = <&reg_5v0>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2.dtsi
index 0462ed2dd8b8..54b7da4b6920 100644
--- a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2.dtsi
@@ -40,7 +40,7 @@
 			phy-names = "pcie-0";
 			status = "okay";
 
-			pcie@0 {
+			ethernet@0,0 {
 				reg = <0 0 0 0 0>;
 				local-mac-address = [00 00 00 00 00 00];
 			};
@@ -57,7 +57,7 @@
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -65,6 +65,24 @@
 		vdd-supply = <&reg_vdd_gpu>;
 	};
 
+	gpio@6000d000 {
+		/* I210 Gigabit Ethernet Controller Reset */
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET_N";
+		};
+
+		/* Control MXM3 pin 26 Reset Module Output Carrier Input */
+		reset-moci-ctrl-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "RESET_MOCI_CTRL";
+		};
+	};
+
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -1539,14 +1557,20 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -1562,6 +1586,7 @@
 		sgtl5000: codec@a {
 			compatible = "fsl,sgtl5000";
 			reg = <0x0a>;
+			#sound-dai-cells = <0>;
 			VDDA-supply = <&reg_module_3v3_audio>;
 			VDDD-supply = <&reg_1v8_vddio>;
 			VDDIO-supply = <&reg_1v8_vddio>;
@@ -1581,18 +1606,18 @@
 			pinctrl-0 = <&as3722_default>;
 
 			as3722_default: pinmux {
+				gpio0-1-3-4-5-6 {
+					pins = "gpio0", "gpio1", "gpio3",
+					       "gpio4", "gpio5", "gpio6";
+					bias-high-impedance;
+				};
+
 				gpio2-7 {
 					pins = "gpio2", /* PWR_EN_+V3.3 */
 					       "gpio7"; /* +V1.6_LPO */
 					function = "gpio";
 					bias-pull-up;
 				};
-
-				gpio0-1-3-4-5-6 {
-					pins = "gpio0", "gpio1", "gpio3",
-					       "gpio4", "gpio5", "gpio6";
-					bias-high-impedance;
-				};
 			};
 
 			regulators {
@@ -1750,7 +1775,7 @@
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 			#thermal-sensor-cells = <1>;
 			vcc-supply = <&reg_module_3v3>;
 		};
@@ -1884,6 +1909,7 @@
 			usb2-0 {
 				status = "okay";
 				mode = "otg";
+				usb-role-switch;
 				vbus-supply = <&reg_usbo1_vbus>;
 			};
 
@@ -1916,7 +1942,7 @@
 	};
 
 	/* eMMC */
-	sdhci@700b0600 {
+	mmc@700b0600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1938,18 +1964,18 @@
 		};
 	};
 
-	clk32k_in: osc3 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-	};
-
 	cpus {
 		cpu@0 {
 			vdd-cpu-supply = <&reg_vdd_cpu>;
 		};
 	};
 
+	clk32k_in: osc3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
 	reg_1v05_avdd_hdmi_pll: regulator-1v05-avdd-hdmi-pll {
 		compatible = "regulator-fixed";
 		regulator-name = "+V1.05_AVDD_HDMI_PLL";
@@ -2009,12 +2035,18 @@
 		nvidia,audio-codec = <&sgtl5000>;
 		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA124_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA124_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA124_CLK_EXTERN1>;
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu-shutdown-trip {
 					temperature = <101000>;
@@ -2024,7 +2056,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			trips {
 				mem-shutdown-trip {
 					temperature = <101000>;
@@ -2034,7 +2066,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			trips {
 				gpu-shutdown-trip {
 					temperature = <101000>;
@@ -2045,21 +2077,3 @@
 		};
 	};
 };
-
-&gpio {
-	/* I210 Gigabit Ethernet Controller Reset */
-	lan-reset-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET_N";
-	};
-
-	/* Control MXM3 pin 26 Reset Module Output Carrier Input */
-	reset-moci-ctrl {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "RESET_MOCI_CTRL";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-apalis.dtsi b/arch/arm/boot/dts/nvidia/tegra124-apalis.dtsi
index d1e8593ef0d9..c5a0d6aebaec 100644
--- a/arch/arm/boot/dts/tegra124-apalis.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis.dtsi
@@ -39,7 +39,7 @@
 			phy-names = "pcie-0";
 			status = "okay";
 
-			pcie@0 {
+			ethernet@0,0 {
 				reg = <0 0 0 0 0>;
 				local-mac-address = [00 00 00 00 00 00];
 			};
@@ -56,7 +56,7 @@
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -64,6 +64,24 @@
 		vdd-supply = <&reg_vdd_gpu>;
 	};
 
+	gpio@6000d000 {
+		/* I210 Gigabit Ethernet Controller Reset */
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET_N";
+		};
+
+		/* Control MXM3 pin 26 Reset Module Output Carrier Input */
+		reset-moci-ctrl-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "RESET_MOCI_CTRL";
+		};
+	};
+
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -1532,14 +1550,20 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c400 {
@@ -1555,6 +1579,7 @@
 		sgtl5000: codec@a {
 			compatible = "fsl,sgtl5000";
 			reg = <0x0a>;
+			#sound-dai-cells = <0>;
 			VDDA-supply = <&reg_module_3v3_audio>;
 			VDDD-supply = <&reg_1v8_vddio>;
 			VDDIO-supply = <&reg_1v8_vddio>;
@@ -1574,18 +1599,18 @@
 			pinctrl-0 = <&as3722_default>;
 
 			as3722_default: pinmux {
+				gpio0-1-3-4-5-6 {
+					pins = "gpio0", "gpio1", "gpio3",
+					       "gpio4", "gpio5", "gpio6";
+					bias-high-impedance;
+				};
+
 				gpio2-7 {
 					pins = "gpio2", /* PWR_EN_+V3.3 */
 					       "gpio7"; /* +V1.6_LPO */
 					function = "gpio";
 					bias-pull-up;
 				};
-
-				gpio0-1-3-4-5-6 {
-					pins = "gpio0", "gpio1", "gpio3",
-					       "gpio4", "gpio5", "gpio6";
-					bias-high-impedance;
-				};
 			};
 
 			regulators {
@@ -1743,7 +1768,7 @@
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 			#thermal-sensor-cells = <1>;
 			vcc-supply = <&reg_module_3v3>;
 		};
@@ -1876,6 +1901,7 @@
 			usb2-0 {
 				status = "okay";
 				mode = "otg";
+				usb-role-switch;
 				vbus-supply = <&reg_usbo1_vbus>;
 			};
 
@@ -1908,7 +1934,7 @@
 	};
 
 	/* eMMC */
-	sdhci@700b0600 {
+	mmc@700b0600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1930,18 +1956,18 @@
 		};
 	};
 
-	clk32k_in: osc3 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-	};
-
 	cpus {
 		cpu@0 {
 			vdd-cpu-supply = <&reg_vdd_cpu>;
 		};
 	};
 
+	clk32k_in: osc3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
 	reg_1v05_avdd_hdmi_pll: regulator-1v05-avdd-hdmi-pll {
 		compatible = "regulator-fixed";
 		regulator-name = "+V1.05_AVDD_HDMI_PLL";
@@ -2001,12 +2027,18 @@
 		nvidia,audio-codec = <&sgtl5000>;
 		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA124_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA124_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA124_CLK_EXTERN1>;
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu-shutdown-trip {
 					temperature = <101000>;
@@ -2016,7 +2048,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			trips {
 				mem-shutdown-trip {
 					temperature = <101000>;
@@ -2026,7 +2058,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			trips {
 				gpu-shutdown-trip {
 					temperature = <101000>;
@@ -2037,21 +2069,3 @@
 		};
 	};
 };
-
-&gpio {
-	/* I210 Gigabit Ethernet Controller Reset */
-	lan-reset-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET_N";
-	};
-
-	/* Control MXM3 pin 26 Reset Module Output Carrier Input */
-	reset-moci-ctrl {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "RESET_MOCI_CTRL";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1-emc.dtsi
index 784a529e1f19..d10e5334a6c6 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1-emc.dtsi
@@ -1,4 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/clock/tegra124-car.h>
+
 / {
 	clock@60006000 {
 		emc-timings-3 {
@@ -10,66 +13,77 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-924000000 {
 				clock-frequency = <924000000>;
 				nvidia,parent-clock-frequency = <924000000>;
@@ -79,7 +93,325 @@
 		};
 	};
 
-	emc@7001b000 {
+	memory-controller@70019000 {
+		emc-timings-3 {
+			nvidia,ram-code = <3>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001
+					0x8000000a
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x77e30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001
+					0x80000012
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x76230303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001
+					0x80000017
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x74a30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001
+					0x8000001e
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x74230403
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001
+					0x80000026
+					0x00000001
+					0x00000001
+					0x00000003
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0503
+					0x73c30504
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003
+					0x80000040
+					0x00000001
+					0x00000001
+					0x00000004
+					0x00000002
+					0x00000003
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040203
+					0x000a0504
+					0x73840a05
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000004
+					0x00000004
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000b0607
+					0x77450e08
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000005
+					0x00000006
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000d0709
+					0x7586120a
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007
+					0x80000040
+					0x00000002
+					0x00000003
+					0x0000000c
+					0x00000007
+					0x00000008
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000006
+					0x06050202
+					0x0010090c
+					0x7428180d
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009
+					0x80000040
+					0x00000003
+					0x00000004
+					0x0000000e
+					0x00000009
+					0x0000000a
+					0x00000001
+					0x00000003
+					0x0000000b
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000007
+					0x07050202
+					0x00130b0e
+					0x73a91b0f
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b
+					0x80000040
+					0x00000004
+					0x00000005
+					0x00000013
+					0x0000000c
+					0x0000000d
+					0x00000002
+					0x00000003
+					0x0000000c
+					0x00000002
+					0x00000002
+					0x00000006
+					0x00000008
+					0x08060202
+					0x00170e13
+					0x736c2414
+					0x70000f02
+					0x001f0000
+				>;
+			};
+
+			timing-924000000 {
+				clock-frequency = <924000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000d
+					0x80000040
+					0x00000005
+					0x00000006
+					0x00000016
+					0x0000000e
+					0x0000000f
+					0x00000002
+					0x00000004
+					0x0000000e
+					0x00000002
+					0x00000002
+					0x00000006
+					0x00000009
+					0x09060202
+					0x001a1016
+					0x734e2a17
+					0x70000f02
+					0x001f0000
+				>;
+			};
+		};
+	};
+
+	external-memory-controller@7001b000 {
 		emc-timings-3 {
 			nvidia,ram-code = <3>;
 
@@ -2098,325 +2430,14 @@
 					0x00000011
 				>;
 			};
-
 		};
 	};
 
-	memory-controller@70019000 {
-		emc-timings-3 {
-			nvidia,ram-code = <3>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001
-					0x8000000a
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x77e30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001
-					0x80000012
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x76230303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001
-					0x80000017
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x74a30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001
-					0x8000001e
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x74230403
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001
-					0x80000026
-					0x00000001
-					0x00000001
-					0x00000003
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0503
-					0x73c30504
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003
-					0x80000040
-					0x00000001
-					0x00000001
-					0x00000004
-					0x00000002
-					0x00000003
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040203
-					0x000a0504
-					0x73840a05
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000004
-					0x00000004
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000b0607
-					0x77450e08
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000005
-					0x00000006
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000d0709
-					0x7586120a
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007
-					0x80000040
-					0x00000002
-					0x00000003
-					0x0000000c
-					0x00000007
-					0x00000008
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000006
-					0x06050202
-					0x0010090c
-					0x7428180d
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009
-					0x80000040
-					0x00000003
-					0x00000004
-					0x0000000e
-					0x00000009
-					0x0000000a
-					0x00000001
-					0x00000003
-					0x0000000b
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000007
-					0x07050202
-					0x00130b0e
-					0x73a91b0f
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b
-					0x80000040
-					0x00000004
-					0x00000005
-					0x00000013
-					0x0000000c
-					0x0000000d
-					0x00000002
-					0x00000003
-					0x0000000c
-					0x00000002
-					0x00000002
-					0x00000006
-					0x00000008
-					0x08060202
-					0x00170e13
-					0x736c2414
-					0x70000f02
-					0x001f0000
-				>;
-			};
-
-			timing-924000000 {
-				clock-frequency = <924000000>;
+	opp-table-actmon {
+		/delete-node/ opp-1200000000;
+	};
 
-				nvidia,emem-configuration = <
-					0x0e00000d
-					0x80000040
-					0x00000005
-					0x00000006
-					0x00000016
-					0x0000000e
-					0x0000000f
-					0x00000002
-					0x00000004
-					0x0000000e
-					0x00000002
-					0x00000002
-					0x00000006
-					0x00000009
-					0x09060202
-					0x001a1016
-					0x734e2a17
-					0x70000f02
-					0x001f0000
-				>;
-			};
-		};
+	opp-table-emc {
+		/delete-node/ opp-1200000000-1100;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1.dts
index d5fd642f8b77..f09109be1152 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1.dts
@@ -68,11 +68,7 @@
 		};
 	};
 
-	cec@70015000 {
-		status = "okay";
-	};
-
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -1389,6 +1385,8 @@
 	 */
 	serial@70006000 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
@@ -1401,11 +1399,15 @@
 	 */
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
 	/* DB9 serial port */
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -1427,7 +1429,7 @@
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 		};
 
 		eeprom@56 {
@@ -1655,7 +1657,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q32dw", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <20000000>;
@@ -1680,6 +1683,10 @@
 		};
 	};
 
+	cec@70015000 {
+		status = "okay";
+	};
+
 	/* Serial ATA */
 	sata@70020000 {
 		status = "okay";
@@ -1785,7 +1792,7 @@
 			/* Micro A/B */
 			usb2-0 {
 				status = "okay";
-				mode = "otg";
+				mode = "host";
 			};
 
 			/* Mini PCIe */
@@ -1810,7 +1817,7 @@
 	};
 
 	/* SD card */
-	sdhci@700b0400 {
+	mmc@700b0400 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 		power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
@@ -1820,7 +1827,7 @@
 	};
 
 	/* eMMC */
-	sdhci@700b0600 {
+	mmc@700b0600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1868,17 +1875,10 @@
 		vbus-supply = <&vdd_usb3_vbus>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	cpus {
@@ -1890,7 +1890,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1899,145 +1899,127 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_mux: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "+VDD_MUX";
-			regulator-min-microvolt = <12000000>;
-			regulator-max-microvolt = <12000000>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
+	vdd_mux: regulator-mux {
+		compatible = "regulator-fixed";
+		regulator-name = "+VDD_MUX";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 
-		vdd_5v0_sys: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "+5V_SYS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_5v0_sys: regulator-5v0sys {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_SYS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_3v3_sys: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "+3.3V_SYS";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_3v3_sys: regulator-3v3sys {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_SYS";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_3v3_run: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "+3.3V_RUN";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
+	vdd_3v3_run: regulator-3v3run {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_RUN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
 
-		vdd_3v3_hdmi: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vdd_3v3_run>;
-		};
+	vdd_3v3_hdmi: regulator-3v3hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vdd_3v3_run>;
+	};
 
-		vdd_usb1_vbus: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "+USB0_VBUS_SW";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_usb1_vbus: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "+USB0_VBUS_SW";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_usb3_vbus: regulator@8 {
-			compatible = "regulator-fixed";
-			reg = <8>;
-			regulator-name = "+5V_USB_HS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_usb3_vbus: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_USB_HS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_3v3_lp0: regulator@10 {
-			compatible = "regulator-fixed";
-			reg = <10>;
-			regulator-name = "+3.3V_LP0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
+	vdd_3v3_lp0: regulator-lp0 {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_LP0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
 
-		vdd_hdmi_pll: regulator@11 {
-			compatible = "regulator-fixed";
-			reg = <11>;
-			regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
-			vin-supply = <&vdd_1v05_run>;
-		};
+	vdd_hdmi_pll: regulator-hdmipll {
+		compatible = "regulator-fixed";
+		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+		vin-supply = <&vdd_1v05_run>;
+	};
 
-		vdd_5v0_hdmi: regulator@12 {
-			compatible = "regulator-fixed";
-			reg = <12>;
-			regulator-name = "+5V_HDMI_CON";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_5v0_hdmi: regulator-hdmicon {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_HDMI_CON";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		/* Molex power connector */
-		vdd_5v0_sata: regulator@13 {
-			compatible = "regulator-fixed";
-			reg = <13>;
-			regulator-name = "+5V_SATA";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(EE, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	/* Molex power connector */
+	vdd_5v0_sata: regulator-5v0sata {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_SATA";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(EE, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_12v0_sata: regulator@14 {
-			compatible = "regulator-fixed";
-			reg = <14>;
-			regulator-name = "+12V_SATA";
-			regulator-min-microvolt = <12000000>;
-			regulator-max-microvolt = <12000000>;
-			gpio = <&gpio TEGRA_GPIO(EE, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_12v0_sata: regulator-12v0sata {
+		compatible = "regulator-fixed";
+		regulator-name = "+12V_SATA";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio TEGRA_GPIO(EE, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_mux>;
 	};
 
 	sound {
@@ -2058,12 +2040,18 @@
 
 		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA124_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA124_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA124_CLK_EXTERN1>;
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu-shutdown-trip {
 					temperature = <101000>;
@@ -2073,7 +2061,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			trips {
 				mem-shutdown-trip {
 					temperature = <101000>;
@@ -2083,7 +2071,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			trips {
 				gpu-shutdown-trip {
 					temperature = <101000>;
diff --git a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-emc.dtsi
index fb6b3e1a0b1f..cadb1969f1cc 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-emc.dtsi
@@ -1,9 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
-/ {
-	apbmisc@70000800 {
-		nvidia,long-ram-code;
-	};
 
+#include <dt-bindings/clock/tegra124-car.h>
+
+/ {
 	clock@60006000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
@@ -14,60 +13,70 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -85,60 +94,70 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -156,60 +175,70 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -219,7 +248,883 @@
 		};
 	};
 
-	emc@7001b000 {
+	apbmisc@70000800 {
+		nvidia,long-ram-code;
+	};
+
+	memory-controller@70019000 {
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 /* MC_EMEM_ARB_CFG */
+					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x76230303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 /* MC_EMEM_ARB_CFG */
+					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74a30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74230403 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 /* MC_EMEM_ARB_CFG */
+					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
+					0x77450e08 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7586120a /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
+					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
+					0x7428180e /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
+					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
+					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x734c2414 /* MC_EMEM_ARB_MISC0 */
+					0x70000f02 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-4 {
+			nvidia,ram-code = <4>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 /* MC_EMEM_ARB_CFG */
+					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x77430303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 /* MC_EMEM_ARB_CFG */
+					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75430403 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 /* MC_EMEM_ARB_CFG */
+					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x74e30504 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0504 /* MC_EMEM_ARB_DA_COVERS */
+					0x74a40a05 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
+					0x77450e08 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7586120a /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RC */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x0010090c /* MC_EMEM_ARB_DA_COVERS */
+					0x7488180d /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
+					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
+					0x74691b0f /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00170e13 /* MC_EMEM_ARB_DA_COVERS */
+					0x746c2414 /* MC_EMEM_ARB_MISC0 */
+					0x70000f02 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-6 {
+			nvidia,ram-code = <6>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 /* MC_EMEM_ARB_CFG */
+					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x76230303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 /* MC_EMEM_ARB_CFG */
+					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74a30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74230403 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 /* MC_EMEM_ARB_CFG */
+					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
+					0x77450e08 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7586120a /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
+					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
+					0x7428180e /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
+					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
+					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x734c2414 /* MC_EMEM_ARB_MISC0 */
+					0x70000f02 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+	};
+
+	external-memory-controller@7001b000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
 
@@ -5777,875 +6682,13 @@
 		};
 	};
 
-	memory-controller@70019000 {
-		emc-timings-1 {
-			nvidia,ram-code = <1>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 /* MC_EMEM_ARB_CFG */
-					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x77e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 /* MC_EMEM_ARB_CFG */
-					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x76230303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 /* MC_EMEM_ARB_CFG */
-					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74a30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 /* MC_EMEM_ARB_CFG */
-					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74230403 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 /* MC_EMEM_ARB_CFG */
-					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
-					0x73c30504 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
-					0x73840a06 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
-					0x77450e08 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-					0x7586120a /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
-					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
-					0x7428180e /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
-					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
-					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-					0x734c2414 /* MC_EMEM_ARB_MISC0 */
-					0x70000f02 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-		};
-
-		emc-timings-4 {
-			nvidia,ram-code = <4>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 /* MC_EMEM_ARB_CFG */
-					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x77e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 /* MC_EMEM_ARB_CFG */
-					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x77430303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 /* MC_EMEM_ARB_CFG */
-					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x75e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 /* MC_EMEM_ARB_CFG */
-					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x75430403 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 /* MC_EMEM_ARB_CFG */
-					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
-					0x74e30504 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0504 /* MC_EMEM_ARB_DA_COVERS */
-					0x74a40a05 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
-					0x77450e08 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-					0x7586120a /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RC */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x0010090c /* MC_EMEM_ARB_DA_COVERS */
-					0x7488180d /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
-					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
-					0x74691b0f /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00170e13 /* MC_EMEM_ARB_DA_COVERS */
-					0x746c2414 /* MC_EMEM_ARB_MISC0 */
-					0x70000f02 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-		};
-
-		emc-timings-6 {
-			nvidia,ram-code = <6>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 /* MC_EMEM_ARB_CFG */
-					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x77e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 /* MC_EMEM_ARB_CFG */
-					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x76230303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 /* MC_EMEM_ARB_CFG */
-					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74a30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 /* MC_EMEM_ARB_CFG */
-					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74230403 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 /* MC_EMEM_ARB_CFG */
-					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
-					0x73c30504 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
-					0x73840a06 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
-					0x77450e08 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-					0x7586120a /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
-					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
-					0x7428180e /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
-					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
-					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
+	opp-table-actmon {
+		/delete-node/ opp-924000000;
+		/delete-node/ opp-1200000000;
+	};
 
-				nvidia,emem-configuration = <
-					0x0e00000b /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-					0x734c2414 /* MC_EMEM_ARB_MISC0 */
-					0x70000f02 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-		};
+	opp-table-emc {
+		/delete-node/ opp-924000000-1100;
+		/delete-node/ opp-1200000000-1100;
 	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra124-nyan-big-fhd.dts b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-fhd.dts
new file mode 100644
index 000000000000..4db43324dafa
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-fhd.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra124-nyan-big.dts"
+
+/ {
+	/* Version of Nyan Big with 1080p panel */
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "auo,b133htn01";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/nvidia/tegra124-nyan-big.dts
index d97791b98958..8bca9599ad6e 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-big.dts
@@ -13,29 +13,23 @@
 		     "google,nyan-big-rev1", "google,nyan-big-rev0",
 		     "google,nyan-big", "google,nyan", "nvidia,tegra124";
 
-	panel: panel {
-		compatible = "auo,b133xtn01";
-
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
-	};
-
-	sdhci@700b0400 { /* SD Card on this bus */
-		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-max98090-nyan-big",
-			     "nvidia,tegra-audio-max98090-nyan",
-			     "nvidia,tegra-audio-max98090";
-		nvidia,model = "GoogleNyanBig";
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "auo,b133xtn01";
+					power-supply = <&vdd_3v3_panel>;
+					backlight = <&backlight>;
+				};
+			};
+		};
 	};
 
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinmux_default>;
 
-		pinmux_default: common {
+		pinmux_default: pinmux {
 			clk_32k_out_pa0 {
 				nvidia,pins = "clk_32k_out_pa0";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -1340,4 +1334,15 @@
 			};
 		};
 	};
+
+	mmc@700b0400 { /* SD Card on this bus */
+		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-max98090-nyan-big",
+			     "nvidia,tegra-audio-max98090-nyan",
+			     "nvidia,tegra-audio-max98090";
+		nvidia,model = "GoogleNyanBig";
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze-emc.dtsi
index c7c31d4c1a2b..e8dcc4f51fc5 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze-emc.dtsi
@@ -1,4 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/clock/tegra124-car.h>
+
 / {
 	clock@60006000 {
 		emc-timings-1 {
@@ -10,55 +13,65 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			/* TODO: Add 528MHz frequency */
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -68,7 +81,299 @@
 		};
 	};
 
-	emc@7001b000 {
+	memory-controller@70019000 {
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001
+					0x8000000a
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x77e30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001
+					0x80000012
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x76230303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001
+					0x80000017
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x74a30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001
+					0x8000001e
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x74230403
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001
+					0x80000026
+					0x00000001
+					0x00000001
+					0x00000003
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0403
+					0x73c30504
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003
+					0x80000040
+					0x00000001
+					0x00000001
+					0x00000005
+					0x00000002
+					0x00000004
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040203
+					0x000a0405
+					0x73840a06
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000004
+					0x00000005
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000b0607
+					0x77450e08
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000005
+					0x00000007
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000d0709
+					0x7586120a
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007
+					0x80000040
+					0x00000002
+					0x00000003
+					0x0000000d
+					0x00000008
+					0x0000000a
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000006
+					0x06050202
+					0x0010090d
+					0x7428180e
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009
+					0x80000040
+					0x00000003
+					0x00000004
+					0x0000000e
+					0x00000009
+					0x0000000b
+					0x00000001
+					0x00000003
+					0x0000000b
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000007
+					0x07050202
+					0x00130b0e
+					0x73a91b0f
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b
+					0x80000040
+					0x00000004
+					0x00000005
+					0x00000013
+					0x0000000c
+					0x0000000f
+					0x00000002
+					0x00000003
+					0x0000000c
+					0x00000002
+					0x00000002
+					0x00000006
+					0x00000008
+					0x08060202
+					0x00160d13
+					0x734c2414
+					0x70000f02
+					0x001f0000
+				>;
+			};
+		};
+	};
+
+	external-memory-controller@7001b000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
 
@@ -1751,300 +2056,16 @@
 					0x0000000f
 				>;
 			};
-
 		};
 	};
 
-	memory-controller@70019000 {
-		emc-timings-1 {
-			nvidia,ram-code = <1>;
-
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001
-					0x8000000a
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x77e30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001
-					0x80000012
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x76230303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001
-					0x80000017
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x74a30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001
-					0x8000001e
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x74230403
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001
-					0x80000026
-					0x00000001
-					0x00000001
-					0x00000003
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0403
-					0x73c30504
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003
-					0x80000040
-					0x00000001
-					0x00000001
-					0x00000005
-					0x00000002
-					0x00000004
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040203
-					0x000a0405
-					0x73840a06
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000004
-					0x00000005
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000b0607
-					0x77450e08
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000005
-					0x00000007
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000d0709
-					0x7586120a
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007
-					0x80000040
-					0x00000002
-					0x00000003
-					0x0000000d
-					0x00000008
-					0x0000000a
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000006
-					0x06050202
-					0x0010090d
-					0x7428180e
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009
-					0x80000040
-					0x00000003
-					0x00000004
-					0x0000000e
-					0x00000009
-					0x0000000b
-					0x00000001
-					0x00000003
-					0x0000000b
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000007
-					0x07050202
-					0x00130b0e
-					0x73a91b0f
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
+	opp-table-actmon {
+		/delete-node/ opp-924000000;
+		/delete-node/ opp-1200000000;
+	};
 
-				nvidia,emem-configuration = <
-					0x0e00000b
-					0x80000040
-					0x00000004
-					0x00000005
-					0x00000013
-					0x0000000c
-					0x0000000f
-					0x00000002
-					0x00000003
-					0x0000000c
-					0x00000002
-					0x00000002
-					0x00000006
-					0x00000008
-					0x08060202
-					0x00160d13
-					0x734c2414
-					0x70000f02
-					0x001f0000
-				>;
-			};
-		};
+	opp-table-emc {
+		/delete-node/ opp-924000000-1100;
+		/delete-node/ opp-1200000000-1100;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze.dts
index 2a029ee86dd7..432540c10065 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze.dts
@@ -15,25 +15,23 @@
 		     "google,nyan-blaze-rev0", "google,nyan-blaze",
 		     "google,nyan", "nvidia,tegra124";
 
-	panel: panel {
-		compatible = "samsung,ltn140at29-301";
-
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-max98090-nyan-blaze",
-			     "nvidia,tegra-audio-max98090-nyan",
-			     "nvidia,tegra-audio-max98090";
-		nvidia,model = "GoogleNyanBlaze";
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "samsung,ltn140at29-301";
+					power-supply = <&vdd_3v3_panel>;
+					backlight = <&backlight>;
+				};
+			};
+		};
 	};
 
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinmux_default>;
 
-		pinmux_default: common {
+		pinmux_default: pinmux {
 			clk_32k_out_pa0 {
 				nvidia,pins = "clk_32k_out_pa0";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -1338,4 +1336,11 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-max98090-nyan-blaze",
+			     "nvidia,tegra-audio-max98090-nyan",
+			     "nvidia,tegra-audio-max98090";
+		nvidia,model = "GoogleNyanBlaze";
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/nvidia/tegra124-nyan.dtsi
index 3b10f475037f..a2ee37180200 100644
--- a/arch/arm/boot/dts/tegra124-nyan.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan.dtsi
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "tegra124.dtsi"
 
 / {
@@ -48,6 +49,9 @@
 		sor@54540000 {
 			status = "okay";
 
+			avdd-io-hdmi-dp-supply = <&vdd_3v3_hdmi>;
+			vdd-hdmi-dp-pll-supply = <&vdd_hdmi_pll>;
+
 			nvidia,dpaux = <&dpaux>;
 			nvidia,panel = <&panel>;
 		};
@@ -58,7 +62,7 @@
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		status = "okay";
 
 		vdd-supply = <&vdd_gpu>;
@@ -66,6 +70,8 @@
 
 	serial@70006000 {
 		/* Debug connector on the bottom of the board near SD card. */
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -84,11 +90,11 @@
 			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
 		};
 
-		temperature-sensor@4c {
+		tmp451: temperature-sensor@4c {
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_EDGE_FALLING>;
 
 			#thermal-sensor-cells = <1>;
 		};
@@ -387,6 +393,10 @@
 		nvidia,sys-clock-req-active-high;
 	};
 
+	cec@70015000 {
+		status = "okay";
+	};
+
 	hda@70030000 {
 		status = "okay";
 	};
@@ -463,6 +473,7 @@
 				vbus-supply = <&vdd_usb1_vbus>;
 				status = "okay";
 				mode = "otg";
+				usb-role-switch;
 			};
 
 			usb2-1 {
@@ -489,13 +500,7 @@
 		};
 	};
 
-	sdhci0_pwrseq: sdhci0_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-
-		reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
-	};
-
-	sdhci@700b0000 { /* WiFi/BT on this bus */
+	mmc@700b0000 { /* WiFi/BT on this bus */
 		status = "okay";
 		bus-width = <4>;
 		no-1-8-v;
@@ -506,7 +511,7 @@
 		keep-power-in-suspend;
 	};
 
-	sdhci@700b0400 { /* SD Card on this bus */
+	mmc@700b0400 { /* SD Card on this bus */
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 		power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
@@ -515,7 +520,7 @@
 		vqmmc-supply = <&vddio_sdmmc3>;
 	};
 
-	sdhci@700b0600 { /* eMMC on this bus */
+	mmc@700b0600 { /* eMMC on this bus */
 		status = "okay";
 		bus-width = <8>;
 		no-1-8-v;
@@ -524,7 +529,7 @@
 
 	/* CPU DFLL clock */
 	clock@70110000 {
-		status = "disabled";
+		status = "okay";
 		vdd-cpu-supply = <&vdd_cpu>;
 		nvidia,i2c-fs-rate = <400000>;
 	};
@@ -579,29 +584,43 @@
 			 256>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	cpus {
-		cpu@0 {
+		cpu0: cpu@0 {
+			#cooling-cells = <2>;
 			vdd-cpu-supply = <&vdd_cpu>;
 		};
+
+		cpu1: cpu@1 {
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			#cooling-cells = <2>;
+		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		lid {
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <30>;
+			wakeup-source;
+		};
+
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;
@@ -609,167 +628,152 @@
 			debounce-interval = <1>;
 			wakeup-source;
 		};
+	};
 
-		power {
-			label = "Power";
-			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <30>;
-			wakeup-source;
-		};
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		priority = <200>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	sdhci0_pwrseq: pwrseq-sdhci0 {
+		compatible = "mmc-pwrseq-simple";
 
-		vdd_mux: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "+VDD_MUX";
-			regulator-min-microvolt = <12000000>;
-			regulator-max-microvolt = <12000000>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
+		reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
+	};
 
-		vdd_5v0_sys: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "+5V_SYS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_mux: regulator-mux {
+		compatible = "regulator-fixed";
+		regulator-name = "+VDD_MUX";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 
-		vdd_3v3_sys: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "+3.3V_SYS";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_5v0_sys: regulator-5v0sys {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_SYS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_3v3_run: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "+3.3V_RUN";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
+	vdd_3v3_sys: regulator-3v3sys {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_SYS";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_3v3_hdmi: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vdd_3v3_run>;
-		};
+	vdd_3v3_run: regulator-3v3run {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_RUN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
 
-		vdd_led: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "+VDD_LED";
-			gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_3v3_hdmi: regulator-3v3hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vdd_3v3_run>;
+	};
 
-		vdd_5v0_ts: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "+5V_VDD_TS_SW";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-boot-on;
-			gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_led: regulator-led {
+		compatible = "regulator-fixed";
+		regulator-name = "+VDD_LED";
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_usb1_vbus: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "+5V_USB_HS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_5v0_ts: regulator-ts {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_VDD_TS_SW";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_usb3_vbus: regulator@8 {
-			compatible = "regulator-fixed";
-			reg = <8>;
-			regulator-name = "+5V_USB_SS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_usb1_vbus: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_USB_HS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_3v3_panel: regulator@9 {
-			compatible = "regulator-fixed";
-			reg = <9>;
-			regulator-name = "+3.3V_PANEL";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_run>;
-		};
+	vdd_usb3_vbus: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_USB_SS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_3v3_lp0: regulator@10 {
-			compatible = "regulator-fixed";
-			reg = <10>;
-			regulator-name = "+3.3V_LP0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			/*
-			 * TODO: find a way to wire this up with the USB EHCI
-			 * controllers so that it can be enabled on demand.
-			 */
-			regulator-always-on;
-			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
+	vdd_3v3_panel: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_PANEL";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_run>;
+	};
 
-		vdd_hdmi_pll: regulator@11 {
-			compatible = "regulator-fixed";
-			reg = <11>;
-			regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
-			vin-supply = <&vdd_1v05_run>;
-		};
+	vdd_3v3_lp0: regulator-lp0 {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_LP0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/*
+		 * TODO: find a way to wire this up with the USB EHCI
+		 * controllers so that it can be enabled on demand.
+		 */
+		regulator-always-on;
+		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
 
-		vdd_5v0_hdmi: regulator@12 {
-			compatible = "regulator-fixed";
-			reg = <12>;
-			regulator-name = "+5V_HDMI_CON";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_hdmi_pll: regulator-hdmipll {
+		compatible = "regulator-fixed";
+		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+		vin-supply = <&vdd_1v05_run>;
+	};
+
+	vdd_5v0_hdmi: regulator-hdmicon {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_HDMI_CON";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
 	};
 
 	sound {
@@ -788,19 +792,47 @@
 
 		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA124_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 
+		assigned-clocks = <&tegra_car TEGRA124_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA124_CLK_EXTERN1>;
+
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
 		nvidia,mic-det-gpios =
 				<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
 	};
 
-	gpio-restart {
-		compatible = "gpio-restart";
-		gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
-		priority = <200>;
+	thermal-zones {
+		cpu-skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&tmp451 0>;
+
+			trips {
+				cpu_passive_trip: cpu-alert0 {
+					/* throttle at 70C until temperature drops to 69.8C */
+					temperature = <70000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_passive_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
 	};
 };
 
-#include "cros-ec-keyboard.dtsi"
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/nvidia/tegra124-peripherals-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra124-peripherals-opp.dtsi
new file mode 100644
index 000000000000..b262c1289da5
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra124-peripherals-opp.dtsi
@@ -0,0 +1,424 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	emc_icc_dvfs_opp_table: opp-table-emc {
+		compatible = "operating-points-v2";
+
+		opp-12750000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-12750000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-12750000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-12750000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-20400000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-20400000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-20400000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-20400000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-40800000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-40800000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-40800000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-40800000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-68000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-68000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-68000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-68000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-102000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-102000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-102000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-102000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-204000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0003>;
+			opp-suspend;
+		};
+
+		opp-204000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0008>;
+			opp-suspend;
+		};
+
+		opp-204000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0010>;
+			opp-suspend;
+		};
+
+		opp-204000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0004>;
+			opp-suspend;
+		};
+
+		opp-264000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-264000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-264000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-264000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-300000000-850 {
+			opp-microvolt = <850000 850000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-300000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-300000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-300000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-348000000-850 {
+			opp-microvolt = <850000 850000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-348000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-348000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-348000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-396000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-396000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-396000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-396000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-528000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-528000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-528000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-528000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-600000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-600000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-600000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-600000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-792000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x000B>;
+		};
+
+		opp-792000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-792000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-924000000-1100 {
+			opp-microvolt = <1100000 1100000 1150000>;
+			opp-hz = /bits/ 64 <924000000>;
+			opp-supported-hw = <0x0013>;
+		};
+
+		opp-1200000000-1100 {
+			opp-microvolt = <1100000 1100000 1150000>;
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-supported-hw = <0x0003>;
+		};
+	};
+
+	emc_bw_dfs_opp_table: opp-table-actmon {
+		compatible = "operating-points-v2";
+
+		opp-12750000 {
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <204000>;
+		};
+
+		opp-20400000 {
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <326400>;
+		};
+
+		opp-40800000 {
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <652800>;
+		};
+
+		opp-68000000 {
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <1088000>;
+		};
+
+		opp-102000000 {
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <1632000>;
+		};
+
+		opp-204000000 {
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <3264000>;
+			opp-suspend;
+		};
+
+		opp-264000000 {
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <4224000>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <4800000>;
+		};
+
+		opp-348000000 {
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <5568000>;
+		};
+
+		opp-396000000 {
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <6336000>;
+		};
+
+		opp-528000000 {
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <8448000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <9600000>;
+		};
+
+		opp-792000000 {
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <12672000>;
+		};
+
+		opp-924000000 {
+			opp-hz = /bits/ 64 <924000000>;
+			opp-supported-hw = <0x0013>;
+			opp-peak-kBps = <14784000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-supported-hw = <0x0003>;
+			opp-peak-kBps = <19200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra124-venice2.dts b/arch/arm/boot/dts/nvidia/tegra124-venice2.dts
index 7309393bfced..3924ee385dee 100644
--- a/arch/arm/boot/dts/tegra124-venice2.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-venice2.dts
@@ -48,10 +48,18 @@
 		dpaux@545c0000 {
 			vdd-supply = <&vdd_3v3_panel>;
 			status = "okay";
+
+			aux-bus {
+				panel: panel {
+					compatible = "lg,lp129qe";
+					power-supply = <&vdd_3v3_panel>;
+					backlight = <&backlight>;
+				};
+			};
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -63,7 +71,7 @@
 		pinctrl-names = "boot";
 		pinctrl-0 = <&pinmux_boot>;
 
-		pinmux_boot: common {
+		pinmux_boot: pinmux {
 			dap_mclk1_pw4 {
 				nvidia,pins = "dap_mclk1_pw4";
 				nvidia,function = "extperiph1";
@@ -601,6 +609,8 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -881,7 +891,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q32dw", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <20000000>;
@@ -972,7 +983,7 @@
 			usb2-0 {
 				status = "okay";
 				mode = "otg";
-
+				usb-role-switch;
 				vbus-supply = <&vdd_usb1_vbus>;
 			};
 
@@ -1002,7 +1013,7 @@
 		};
 	};
 
-	sdhci@700b0400 {
+	mmc@700b0400 {
 		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
 		power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
 		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
@@ -1011,7 +1022,7 @@
 		vqmmc-supply = <&vddio_sdmmc3>;
 	};
 
-	sdhci@700b0600 {
+	mmc@700b0600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1061,23 +1072,16 @@
 		default-brightness-level = <6>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1086,166 +1090,140 @@
 		};
 	};
 
-	panel: panel {
-		compatible = "lg,lp129qe", "simple-panel";
-
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
+	vdd_mux: regulator-mux {
+		compatible = "regulator-fixed";
+		regulator-name = "+VDD_MUX";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_mux: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "+VDD_MUX";
-			regulator-min-microvolt = <12000000>;
-			regulator-max-microvolt = <12000000>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
-
-		vdd_5v0_sys: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "+5V_SYS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_5v0_sys: regulator-5v0sys {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_SYS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_3v3_sys: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "+3.3V_SYS";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_3v3_sys: regulator-3v3sys {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_SYS";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_3v3_run: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "+3.3V_RUN";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
+	vdd_3v3_run: regulator-3v3run {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_RUN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
 
-		vdd_3v3_hdmi: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vdd_3v3_run>;
-		};
+	vdd_3v3_hdmi: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vdd_3v3_run>;
+	};
 
-		vdd_led: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "+VDD_LED";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_mux>;
-		};
+	vdd_led: regulator-led {
+		compatible = "regulator-fixed";
+		regulator-name = "+VDD_LED";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_mux>;
+	};
 
-		vdd_5v0_ts: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "+5V_VDD_TS_SW";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-boot-on;
-			gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_5v0_ts: regulator-ts {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_VDD_TS_SW";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_usb1_vbus: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "+5V_USB_HS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_usb1_vbus: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_USB_HS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_usb3_vbus: regulator@8 {
-			compatible = "regulator-fixed";
-			reg = <8>;
-			regulator-name = "+5V_USB_SS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_usb3_vbus: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_USB_SS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
 
-		vdd_3v3_panel: regulator@9 {
-			compatible = "regulator-fixed";
-			reg = <9>;
-			regulator-name = "+3.3V_PANEL";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_run>;
-		};
+	vdd_3v3_panel: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_PANEL";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_run>;
+	};
 
-		vdd_3v3_lp0: regulator@10 {
-			compatible = "regulator-fixed";
-			reg = <10>;
-			regulator-name = "+3.3V_LP0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			/*
-			 * TODO: find a way to wire this up with the USB EHCI
-			 * controllers so that it can be enabled on demand.
-			 */
-			regulator-always-on;
-			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
+	vdd_3v3_lp0: regulator-lp0 {
+		compatible = "regulator-fixed";
+		regulator-name = "+3.3V_LP0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/*
+		 * TODO: find a way to wire this up with the USB EHCI
+		 * controllers so that it can be enabled on demand.
+		 */
+		regulator-always-on;
+		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
 
-		vdd_hdmi_pll: regulator@11 {
-			compatible = "regulator-fixed";
-			reg = <11>;
-			regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
-			vin-supply = <&vdd_1v05_run>;
-		};
+	vdd_hdmi_pll: regulator-hdmipll {
+		compatible = "regulator-fixed";
+		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+		vin-supply = <&vdd_1v05_run>;
+	};
 
-		vdd_5v0_hdmi: regulator@12 {
-			compatible = "regulator-fixed";
-			reg = <12>;
-			regulator-name = "+5V_HDMI_CON";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
+	vdd_5v0_hdmi: regulator-hdmicon {
+		compatible = "regulator-fixed";
+		regulator-name = "+5V_HDMI_CON";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
 	};
 
 	sound {
@@ -1266,9 +1244,15 @@
 
 		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA124_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA124_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA124_CLK_EXTERN1>;
 	};
 };
 
-#include "cros-ec-keyboard.dtsi"
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/nvidia/tegra124.dtsi
index 413bfb981de8..8f1fff373461 100644
--- a/arch/arm/boot/dts/tegra124.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124.dtsi
@@ -6,6 +6,9 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/reset/tegra124-car.h>
 #include <dt-bindings/thermal/tegra124-soctherm.h>
+#include <dt-bindings/soc/tegra-pmc.h>
+
+#include "tegra124-peripherals-opp.dtsi"
 
 / {
 	compatible = "nvidia,tegra124";
@@ -21,9 +24,9 @@
 	pcie@1003000 {
 		compatible = "nvidia,tegra124-pcie";
 		device_type = "pci";
-		reg = <0x0 0x01003000 0x0 0x00000800   /* PADS registers */
-		       0x0 0x01003800 0x0 0x00000800   /* AFI registers */
-		       0x0 0x02000000 0x0 0x10000000>; /* configuration space */
+		reg = <0x0 0x01003000 0x0 0x00000800>, /* PADS registers */
+		      <0x0 0x01003800 0x0 0x00000800>, /* AFI registers */
+		      <0x0 0x02000000 0x0 0x10000000>; /* configuration space */
 		reg-names = "pads", "afi", "cs";
 		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
 			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
@@ -37,11 +40,11 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 
-		ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000   /* port 0 configuration space */
-			  0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000   /* port 1 configuration space */
-			  0x81000000 0 0x0        0x0 0x12000000 0 0x00010000   /* downstream I/O (64 KiB) */
-			  0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000   /* non-prefetchable memory (208 MiB) */
-			  0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */
+		ranges = <0x02000000 0 0x01000000 0x0 0x01000000 0 0x00001000>, /* port 0 configuration space */
+			 <0x02000000 0 0x01001000 0x0 0x01001000 0 0x00001000>, /* port 1 configuration space */
+			 <0x01000000 0 0x0        0x0 0x12000000 0 0x00010000>, /* downstream I/O (64 KiB) */
+			 <0x02000000 0 0x13000000 0x0 0x13000000 0 0x0d000000>, /* non-prefetchable memory (208 MiB) */
+			 <0x42000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */
 
 		clocks = <&tegra_car TEGRA124_CLK_PCIE>,
 			 <&tegra_car TEGRA124_CLK_AFI>,
@@ -84,13 +87,15 @@
 	};
 
 	host1x@50000000 {
-		compatible = "nvidia,tegra124-host1x", "simple-bus";
+		compatible = "nvidia,tegra124-host1x";
 		reg = <0x0 0x50000000 0x0 0x00034000>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */
 			     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */
+		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA124_CLK_HOST1X>;
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		clock-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA124_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 		iommus = <&mc TEGRA_SWGROUP_HC>;
 
 		#address-cells = <2>;
@@ -102,30 +107,50 @@
 			compatible = "nvidia,tegra124-dc";
 			reg = <0x0 0x54200000 0x0 0x00040000>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&tegra_car TEGRA124_CLK_DISP1>,
-				 <&tegra_car TEGRA124_CLK_PLL_P>;
-			clock-names = "dc", "parent";
+			clocks = <&tegra_car TEGRA124_CLK_DISP1>;
+			clock-names = "dc";
 			resets = <&tegra_car 27>;
 			reset-names = "dc";
 
 			iommus = <&mc TEGRA_SWGROUP_DC>;
 
 			nvidia,head = <0>;
+
+			interconnects = <&mc TEGRA124_MC_DISPLAY0A &emc>,
+					<&mc TEGRA124_MC_DISPLAY0B &emc>,
+					<&mc TEGRA124_MC_DISPLAY0C &emc>,
+					<&mc TEGRA124_MC_DISPLAYHC &emc>,
+					<&mc TEGRA124_MC_DISPLAYD &emc>,
+					<&mc TEGRA124_MC_DISPLAYT &emc>;
+			interconnect-names = "wina",
+					     "winb",
+					     "winc",
+					     "cursor",
+					     "wind",
+					     "wint";
 		};
 
 		dc@54240000 {
 			compatible = "nvidia,tegra124-dc";
 			reg = <0x0 0x54240000 0x0 0x00040000>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&tegra_car TEGRA124_CLK_DISP2>,
-				 <&tegra_car TEGRA124_CLK_PLL_P>;
-			clock-names = "dc", "parent";
+			clocks = <&tegra_car TEGRA124_CLK_DISP2>;
+			clock-names = "dc";
 			resets = <&tegra_car 26>;
 			reset-names = "dc";
 
 			iommus = <&mc TEGRA_SWGROUP_DCB>;
 
 			nvidia,head = <1>;
+
+			interconnects = <&mc TEGRA124_MC_DISPLAY0AB &emc>,
+					<&mc TEGRA124_MC_DISPLAY0BB &emc>,
+					<&mc TEGRA124_MC_DISPLAY0CB &emc>,
+					<&mc TEGRA124_MC_DISPLAYHCB &emc>;
+			interconnect-names = "wina",
+					     "winb",
+					     "winc",
+					     "cursor";
 		};
 
 		hdmi: hdmi@54280000 {
@@ -177,6 +202,11 @@
 			resets = <&tegra_car 181>;
 			reset-names = "dpaux";
 			status = "disabled";
+
+			i2c-bus {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 	};
 
@@ -193,12 +223,7 @@
 		interrupt-parent = <&gic>;
 	};
 
-	/*
-	 * Please keep the following 0, notation in place as a former mainline
-	 * U-Boot version was looking for that particular notation in order to
-	 * perform required fix-ups on that GPU node.
-	 */
-	gpu@0,57000000 {
+	gpu@57000000 {
 		compatible = "nvidia,gk20a";
 		reg = <0x0 0x57000000 0x0 0x01000000>,
 		      <0x0 0x58000000 0x0 0x01000000>;
@@ -229,7 +254,7 @@
 	};
 
 	timer@60005000 {
-		compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+		compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer";
 		reg = <0x0 0x60005000 0x0 0x400>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
@@ -253,7 +278,7 @@
 		reg = <0x0 0x60007000 0x0 0x1000>;
 	};
 
-	actmon@6000c800 {
+	actmon: actmon@6000c800 {
 		compatible = "nvidia,tegra124-actmon";
 		reg = <0x0 0x6000c800 0x0 0x400>;
 		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
@@ -262,6 +287,10 @@
 		clock-names = "actmon", "emc";
 		resets = <&tegra_car 119>;
 		reset-names = "actmon";
+		operating-points-v2 = <&emc_bw_dfs_opp_table>;
+		interconnects = <&mc TEGRA124_MC_MPCORER &emc>;
+		interconnect-names = "cpu-read";
+		#cooling-cells = <2>;
 	};
 
 	gpio: gpio@6000d000 {
@@ -279,9 +308,7 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 251>;
-		*/
 	};
 
 	apbdma: dma@60020000 {
@@ -353,7 +380,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -366,7 +392,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -379,7 +404,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -392,7 +416,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -409,7 +432,7 @@
 	};
 
 	i2c@7000c000 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c000 0x0 0x100>;
 		interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -424,7 +447,7 @@
 	};
 
 	i2c@7000c400 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c400 0x0 0x100>;
 		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -439,7 +462,7 @@
 	};
 
 	i2c@7000c500 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c500 0x0 0x100>;
 		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -454,7 +477,7 @@
 	};
 
 	i2c@7000c700 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c700 0x0 0x100>;
 		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -469,7 +492,7 @@
 	};
 
 	i2c@7000d000 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000d000 0x0 0x100>;
 		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -484,7 +507,7 @@
 	};
 
 	i2c@7000d100 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000d100 0x0 0x100>;
 		interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -595,11 +618,12 @@
 		clocks = <&tegra_car TEGRA124_CLK_RTC>;
 	};
 
-	pmc@7000e400 {
+	tegra_pmc: pmc@7000e400 {
 		compatible = "nvidia,tegra124-pmc";
 		reg = <0x0 0x7000e400 0x0 0x400>;
 		clocks = <&tegra_car TEGRA124_CLK_PCLK>, <&clk32k_in>;
 		clock-names = "pclk", "clk32k_in";
+		#clock-cells = <1>;
 	};
 
 	fuse@7000f800 {
@@ -611,6 +635,16 @@
 		reset-names = "fuse";
 	};
 
+	cec@70015000 {
+		compatible = "nvidia,tegra124-cec";
+		reg = <0x0 0x70015000 0x0 0x00001000>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA124_CLK_CEC>;
+		clock-names = "cec";
+		status = "disabled";
+		hdmi-phandle = <&hdmi>;
+	};
+
 	mc: memory-controller@70019000 {
 		compatible = "nvidia,tegra124-mc";
 		reg = <0x0 0x70019000 0x0 0x1000>;
@@ -620,13 +654,20 @@
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 
 		#iommu-cells = <1>;
+		#reset-cells = <1>;
+		#interconnect-cells = <1>;
 	};
 
-	emc: emc@7001b000 {
+	emc: external-memory-controller@7001b000 {
 		compatible = "nvidia,tegra124-emc";
 		reg = <0x0 0x7001b000 0x0 0x1000>;
+		clocks = <&tegra_car TEGRA124_CLK_EMC>;
+		clock-names = "emc";
 
 		nvidia,memory-controller = <&mc>;
+		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
+
+		#interconnect-cells = <0>;
 	};
 
 	sata@70020000 {
@@ -635,14 +676,12 @@
 		      <0x0 0x70020000 0x0 0x7000>; /* SATA */
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SATA>,
-			 <&tegra_car TEGRA124_CLK_SATA_OOB>,
-			 <&tegra_car TEGRA124_CLK_CML1>,
-			 <&tegra_car TEGRA124_CLK_PLL_E>;
-		clock-names = "sata", "sata-oob", "cml1", "pll_e";
+			 <&tegra_car TEGRA124_CLK_SATA_OOB>;
+		clock-names = "sata", "sata-oob";
 		resets = <&tegra_car 124>,
-			 <&tegra_car 123>,
-			 <&tegra_car 129>;
-		reset-names = "sata", "sata-oob", "sata-cold";
+			 <&tegra_car 129>,
+			 <&tegra_car 123>;
+		reset-names = "sata", "sata-cold", "sata-oob";
 		status = "disabled";
 	};
 
@@ -829,64 +868,60 @@
 		};
 	};
 
-	sdhci@700b0000 {
+	mmc@700b0000 {
 		compatible = "nvidia,tegra124-sdhci";
 		reg = <0x0 0x700b0000 0x0 0x200>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SDMMC1>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 14>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@700b0200 {
+	mmc@700b0200 {
 		compatible = "nvidia,tegra124-sdhci";
 		reg = <0x0 0x700b0200 0x0 0x200>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SDMMC2>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 9>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@700b0400 {
+	mmc@700b0400 {
 		compatible = "nvidia,tegra124-sdhci";
 		reg = <0x0 0x700b0400 0x0 0x200>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SDMMC3>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 69>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@700b0600 {
+	mmc@700b0600 {
 		compatible = "nvidia,tegra124-sdhci";
 		reg = <0x0 0x700b0600 0x0 0x200>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SDMMC4>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 15>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	cec@70015000 {
-		compatible = "nvidia,tegra124-cec";
-		reg = <0x0 0x70015000 0x0 0x00001000>;
-		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA124_CLK_CEC>;
-		clock-names = "cec";
-		status = "disabled";
-		hdmi-phandle = <&hdmi>;
-	};
-
 	soctherm: thermal-sensor@700e2000 {
 		compatible = "nvidia,tegra124-soctherm";
-		reg = <0x0 0x700e2000 0x0 0x600 /* SOC_THERM reg_base */
-			0x0 0x60006000 0x0 0x400>; /* CAR reg_base */
+		reg = <0x0 0x700e2000 0x0 0x600>, /* SOC_THERM reg_base */
+		      <0x0 0x60006000 0x0 0x400>; /* CAR reg_base */
 		reg-names = "soctherm-reg", "car-reg";
-		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "thermal", "edp";
 		clocks = <&tegra_car TEGRA124_CLK_TSENSOR>,
-			<&tegra_car TEGRA124_CLK_SOC_THERM>;
+			 <&tegra_car TEGRA124_CLK_SOC_THERM>;
 		clock-names = "tsensor", "soctherm";
 		resets = <&tegra_car 78>;
 		reset-names = "soctherm";
@@ -896,6 +931,7 @@
 			throttle_heavy: heavy {
 				nvidia,priority = <100>;
 				nvidia,cpu-throt-percent = <85>;
+				nvidia,gpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_HIGH>;
 
 				#cooling-cells = <2>;
 			};
@@ -1030,7 +1066,7 @@
 	};
 
 	usb@7d000000 {
-		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d000000 0x0 0x4000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1045,6 +1081,7 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d000000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USBD>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
@@ -1052,6 +1089,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 22>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -1063,11 +1101,12 @@
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
 		nvidia,has-utmi-pad-registers;
+		nvidia,pmc = <&tegra_pmc 0>;
 		status = "disabled";
 	};
 
 	usb@7d004000 {
-		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d004000 0x0 0x4000>;
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1082,6 +1121,7 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d004000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB2>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
@@ -1089,6 +1129,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 58>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -1099,11 +1140,12 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,pmc = <&tegra_pmc 1>;
 		status = "disabled";
 	};
 
 	usb@7d008000 {
-		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d008000 0x0 0x4000>;
 		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1118,6 +1160,7 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d008000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB3>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
@@ -1125,6 +1168,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 59>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -1135,6 +1179,7 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,pmc = <&tegra_pmc 2>;
 		status = "disabled";
 	};
 
@@ -1189,7 +1234,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1217,7 +1262,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1230,6 +1275,11 @@
 					hysteresis = <0>;
 					type = "critical";
 				};
+				mem-throttle-trip {
+					temperature = <99000>;
+					hysteresis = <1000>;
+					type = "hot";
+				};
 			};
 
 			cooling-maps {
@@ -1240,7 +1290,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1268,7 +1318,7 @@
 			};
 		};
 
-		pllx {
+		pllx-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1281,6 +1331,11 @@
 					hysteresis = <0>;
 					type = "critical";
 				};
+				pllx-throttle-trip {
+					temperature = <99000>;
+					hysteresis = <1000>;
+					type = "hot";
+				};
 			};
 
 			cooling-maps {
diff --git a/arch/arm/boot/dts/nvidia/tegra20-acer-a500-picasso.dts b/arch/arm/boot/dts/nvidia/tegra20-acer-a500-picasso.dts
new file mode 100644
index 000000000000..a619ea83ed3b
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra20-acer-a500-picasso.dts
@@ -0,0 +1,1527 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/atmel-maxtouch.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra20.dtsi"
+#include "tegra20-cpu-opp.dtsi"
+#include "tegra20-cpu-opp-microvolt.dtsi"
+
+/ {
+	model = "Acer Iconia Tab A500";
+	compatible = "acer,picasso", "nvidia,tegra20";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc3; /* MicroSD */
+		mmc2 = &sdmmc1; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd; /* Docking station */
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	memory@0 {
+		reg = <0x00000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@2ffe0000 {
+			compatible = "ramoops";
+			reg = <0x2ffe0000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		linux,cma@30000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x30000000 0x10000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+	};
+
+	host1x@50000000 {
+		dc@54200000 {
+			rgb {
+				status = "okay";
+
+				port {
+					lcd_output: endpoint {
+						remote-endpoint = <&lvds_encoder_input>;
+						bus-width = <18>;
+					};
+				};
+			};
+		};
+
+		hdmi@54280000 {
+			status = "okay";
+
+			vdd-supply = <&hdmi_vdd_reg>;
+			pll-supply = <&hdmi_pll_reg>;
+			hdmi-supply = <&vdd_5v0_sys>;
+
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7)
+				GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	pinmux@70000014 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			ata {
+				nvidia,pins = "ata";
+				nvidia,function = "ide";
+			};
+			atb {
+				nvidia,pins = "atb", "gma", "gme";
+				nvidia,function = "sdio4";
+			};
+			atc {
+				nvidia,pins = "atc";
+				nvidia,function = "nand";
+			};
+			atd {
+				nvidia,pins = "atd", "ate", "gmb", "spia",
+					"spib", "spic";
+				nvidia,function = "gmi";
+			};
+			cdev1 {
+				nvidia,pins = "cdev1";
+				nvidia,function = "plla_out";
+			};
+			cdev2 {
+				nvidia,pins = "cdev2";
+				nvidia,function = "pllp_out4";
+			};
+			crtp {
+				nvidia,pins = "crtp", "lm1";
+				nvidia,function = "crt";
+			};
+			csus {
+				nvidia,pins = "csus";
+				nvidia,function = "vi_sensor_clk";
+			};
+			dap1 {
+				nvidia,pins = "dap1";
+				nvidia,function = "dap1";
+			};
+			dap2 {
+				nvidia,pins = "dap2";
+				nvidia,function = "dap2";
+			};
+			dap3 {
+				nvidia,pins = "dap3";
+				nvidia,function = "dap3";
+			};
+			dap4 {
+				nvidia,pins = "dap4";
+				nvidia,function = "dap4";
+			};
+			dta {
+				nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+				nvidia,function = "vi";
+			};
+			dtf {
+				nvidia,pins = "dtf";
+				nvidia,function = "i2c3";
+			};
+			gmc {
+				nvidia,pins = "gmc";
+				nvidia,function = "uartd";
+			};
+			gmd {
+				nvidia,pins = "gmd";
+				nvidia,function = "sflash";
+			};
+			gpu {
+				nvidia,pins = "gpu";
+				nvidia,function = "pwm";
+			};
+			gpu7 {
+				nvidia,pins = "gpu7";
+				nvidia,function = "rtck";
+			};
+			gpv {
+				nvidia,pins = "gpv", "slxa";
+				nvidia,function = "pcie";
+			};
+			hdint {
+				nvidia,pins = "hdint";
+				nvidia,function = "hdmi";
+			};
+			i2cp {
+				nvidia,pins = "i2cp";
+				nvidia,function = "i2cp";
+			};
+			irrx {
+				nvidia,pins = "irrx", "irtx";
+				nvidia,function = "uartb";
+			};
+			kbca {
+				nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+					"kbce", "kbcf";
+				nvidia,function = "kbc";
+			};
+			lcsn {
+				nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
+					"lsdi", "lvp0";
+				nvidia,function = "rsvd4";
+			};
+			ld0 {
+				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+					"ld5", "ld6", "ld7", "ld8", "ld9",
+					"ld10", "ld11", "ld12", "ld13", "ld14",
+					"ld15", "ld16", "ld17", "ldi", "lhp0",
+					"lhp1", "lhp2", "lhs", "lpp", "lsc0",
+					"lsc1", "lsck", "lsda", "lspi", "lvp1",
+					"lvs";
+				nvidia,function = "displaya";
+			};
+			owc {
+				nvidia,pins = "owc", "spdi", "spdo", "uac";
+				nvidia,function = "rsvd2";
+			};
+			pmc {
+				nvidia,pins = "pmc";
+				nvidia,function = "pwr_on";
+			};
+			rm {
+				nvidia,pins = "rm";
+				nvidia,function = "i2c1";
+			};
+			sdb {
+				nvidia,pins = "sdb", "sdc", "sdd", "slxc", "slxk";
+				nvidia,function = "sdio3";
+			};
+			sdio1 {
+				nvidia,pins = "sdio1";
+				nvidia,function = "sdio1";
+			};
+			slxd {
+				nvidia,pins = "slxd";
+				nvidia,function = "spdif";
+			};
+			spid {
+				nvidia,pins = "spid", "spie", "spif";
+				nvidia,function = "spi1";
+			};
+			spig {
+				nvidia,pins = "spig", "spih";
+				nvidia,function = "spi2_alt";
+			};
+			uaa {
+				nvidia,pins = "uaa", "uab", "uda";
+				nvidia,function = "ulpi";
+			};
+			uad {
+				nvidia,pins = "uad";
+				nvidia,function = "irda";
+			};
+			uca {
+				nvidia,pins = "uca", "ucb";
+				nvidia,function = "uartc";
+			};
+			conf_ata {
+				nvidia,pins = "ata", "atb", "atc", "atd",
+					"cdev1", "cdev2", "csus", "dap1",
+					"dap4", "dte", "dtf", "gma", "gmc",
+					"gme", "gpu", "gpu7", "gpv", "i2cp",
+					"irrx", "irtx", "pta", "rm",
+					"sdc", "sdd", "slxc", "slxd", "slxk",
+					"spdi", "spdo", "uac", "uad", "uda";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+			conf_ate {
+				nvidia,pins = "ate", "dap2", "dap3",
+					"gmd", "owc", "spia", "spib", "spic",
+					"spid", "spie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+			conf_ck32 {
+				nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+					"pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+			};
+			conf_crtp {
+				nvidia,pins = "crtp", "gmb", "slxa", "spig",
+					"spih";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+			conf_dta {
+				nvidia,pins = "dta", "dtb", "dtc", "dtd", "kbcb";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+			conf_dte {
+				nvidia,pins = "spif";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+			conf_hdint {
+				nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+					"lpw1", "lsck", "lsda", "lsdi",
+					"lvp0";
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+			conf_kbca {
+				nvidia,pins = "kbca", "kbcc", "kbcd",
+					"kbce", "kbcf", "sdio1", "uaa",
+					"uab", "uca", "ucb";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+			conf_lc {
+				nvidia,pins = "lc", "ls";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+			};
+			conf_ld0 {
+				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+					"ld5", "ld6", "ld7", "ld8", "ld9",
+					"ld10", "ld11", "ld12", "ld13", "ld14",
+					"ld15", "ld16", "ld17", "ldi", "lhp0",
+					"lhp1", "lhp2", "lhs", "lm0", "lpp",
+					"lpw0", "lpw2", "lsc0", "lsc1", "lspi",
+					"lvp1", "lvs", "pmc", "sdb";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+			conf_ld17_0 {
+				nvidia,pins = "ld17_0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+			};
+			drive_ddc {
+				nvidia,pins = "drive_ddc",
+						"drive_vi1",
+						"drive_sdio1";
+				nvidia,pull-up-strength = <31>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+			drive_dbg {
+				nvidia,pins = "drive_dbg",
+						"drive_vi2",
+						"drive_at1",
+						"drive_ao1";
+				nvidia,pull-up-strength = <31>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+		};
+
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "i2c2";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "rsvd4";
+			};
+		};
+
+		state_i2cmux_idle: pinmux-i2cmux-idle {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "rsvd4";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "rsvd4";
+			};
+		};
+
+		state_i2cmux_pta: pinmux-i2cmux-pta {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "rsvd4";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "i2c2";
+			};
+		};
+	};
+
+	tegra_spdif: spdif@70002400 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
+	tegra_i2s1: i2s@70002800 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		/* GPS BCM4751 */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Azurewave AW-NH665 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			/* PLLP 216MHz / 16 / 4 */
+			max-speed = <3375000>;
+
+			clocks = <&rtc_32k_wifi>;
+			clock-names = "txco";
+
+			vbat-supply  = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8_sys>;
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	uartd: serial@70006300 {
+		/* Docking station */
+	};
+
+	pwm: pwm@7000a000 {
+		status = "okay";
+	};
+
+	i2c@7000c000 {
+		clock-frequency = <400000>;
+		status = "okay";
+
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 3) IRQ_TYPE_EDGE_BOTH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <
+				0x0000 /* MIC_LR_OUT#    GPIO, output, low */
+				0x0000 /* FM2018-enable  GPIO, output, low */
+				0x0000 /* Speaker-enable GPIO, output, low */
+				0x0200 /* Interrupt, output */
+				0x01a0 /* BCLK, input, active high */
+			>;
+
+			AVDD-supply  = <&vdd_1v8_sys>;
+			CPVDD-supply = <&vdd_1v8_sys>;
+			DBVDD-supply = <&vdd_1v8_sys>;
+			DCVDD-supply = <&vdd_1v8_sys>;
+		};
+
+		touchscreen@4c {
+			compatible = "atmel,maxtouch";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(V, 6) IRQ_TYPE_LEVEL_LOW>;
+
+			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+
+			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Z, 4) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply    = <&vdd_3v3_sys>;
+			vlogic-supply = <&vdd_1v8_sys>;
+
+			mount-matrix =	 "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0x0f>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(S, 7) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply   = <&vdd_1v8_sys>;
+					vddio-supply = <&vdd_1v8_sys>;
+
+					mount-matrix =	 "0",  "1",  "0",
+							 "1",  "0",  "0",
+							 "0",  "0", "-1";
+				};
+			};
+		};
+	};
+
+	i2c@7000c400 {
+		clock-frequency = <10000>;
+		status = "okay";
+	};
+
+	i2c@7000d000 {
+		clock-frequency = <100000>;
+		status = "okay";
+
+		magnetometer@c {
+			compatible = "asahi-kasei,ak8975";
+			reg = <0x0c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 5) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+			vid-supply = <&vdd_1v8_sys>;
+
+			mount-matrix =	"1",  "0",  "0",
+					"0", "-1",  "0",
+					"0",  "0", "-1";
+		};
+
+		pmic: pmic@34 {
+			compatible = "ti,tps6586x";
+			reg = <0x34>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			sys-supply       = <&vdd_5v0_sys>;
+			vin-sm0-supply   = <&sys_reg>;
+			vin-sm1-supply   = <&sys_reg>;
+			vin-sm2-supply   = <&sys_reg>;
+			vinldo01-supply  = <&sm2_reg>;
+			vinldo23-supply  = <&sm2_reg>;
+			vinldo4-supply   = <&sm2_reg>;
+			vinldo678-supply = <&sm2_reg>;
+			vinldo9-supply   = <&sm2_reg>;
+
+			regulators {
+				sys_reg: sys {
+					regulator-name = "vdd_sys";
+					regulator-always-on;
+				};
+
+				vdd_core: sm0 {
+					regulator-name = "vdd_sm0,vdd_core";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&rtc_vdd &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
+				};
+
+				vdd_cpu: sm1 {
+					regulator-name = "vdd_sm1,vdd_cpu";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-coupled-with = <&vdd_core &rtc_vdd>;
+					regulator-coupled-max-spread = <550000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				sm2_reg: sm2 {
+					regulator-name = "vdd_sm2,vin_ldo*";
+					regulator-min-microvolt = <3700000>;
+					regulator-max-microvolt = <3700000>;
+					regulator-always-on;
+				};
+
+				/* LDO0 is not connected to anything */
+
+				ldo1 {
+					regulator-name = "vdd_ldo1,avdd_pll*";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				rtc_vdd: ldo2 {
+					regulator-name = "vdd_ldo2,vdd_rtc";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&vdd_core &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-rtc-regulator;
+				};
+
+				ldo3 {
+					regulator-name = "vdd_ldo3,avdd_usb*";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_ldo4,avdd_osc,vddio_sys";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vcore_emmc: ldo5 {
+					regulator-name = "vdd_ldo5,vcore_mmc";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				avdd_vdac_reg: ldo6 {
+					regulator-name = "vdd_ldo6,avdd_vdac";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+				};
+
+				hdmi_vdd_reg: ldo7 {
+					regulator-name = "vdd_ldo7,avdd_hdmi";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				hdmi_pll_reg: ldo8 {
+					regulator-name = "vdd_ldo8,avdd_hdmi_pll";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo9 {
+					regulator-name = "vdd_ldo9,avdd_2v85,vdd_ddr_rx";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo_rtc {
+					regulator-name = "vdd_rtc_out,vdd_cell";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+
+		nct1008: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+			vcc-supply = <&vdd_3v3_sys>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 6) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	pmc@7000e400 {
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <1>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <100>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <458>;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+	};
+
+	memory-controller@7000f400 {
+		nvidia,use-ram-code;
+
+		emc-tables@0 {
+			nvidia,ram-code = <0>; /* elpida-8gb */
+			reg = <0>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			emc-table@25000 {
+				reg = <25000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <25000>;
+				nvidia,emc-registers = <0x00000002 0x00000006
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000004
+					0x00000003 0x00000008 0x0000000b 0x0000004d
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000068 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@50000 {
+				reg = <50000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <50000>;
+				nvidia,emc-registers = <0x00000003 0x00000007
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000009f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000007
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x000000d0 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000005
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@75000 {
+				reg = <75000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <75000>;
+				nvidia,emc-registers = <0x00000005 0x0000000a
+					0x00000004 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x000000ff
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x0000000b
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000138 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000007
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@150000 {
+				reg = <150000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <150000>;
+				nvidia,emc-registers = <0x00000009 0x00000014
+					0x00000007 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000021f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000015
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000270 0x00000000 0x00000001
+					0x00000000 0x00000000 0x00000282 0xa07c04ae
+					0x007dd510 0x00000000 0x00000000 0x0000000e
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@300000 {
+				reg = <300000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <300000>;
+				nvidia,emc-registers = <0x00000012 0x00000027
+					0x0000000d 0x00000006 0x00000007 0x00000005
+					0x00000003 0x00000009 0x00000006 0x00000006
+					0x00000003 0x00000003 0x00000002 0x00000006
+					0x00000003 0x00000009 0x0000000c 0x0000045f
+					0x00000000 0x00000004 0x00000004 0x00000006
+					0x00000008 0x00000001 0x0000000e 0x0000002a
+					0x00000003 0x0000000f 0x00000007 0x00000005
+					0x00000002 0x000004e1 0x00000005 0x00000002
+					0x00000000 0x00000000 0x00000282 0xe059048b
+					0x007e1510 0x00000000 0x00000000 0x0000001b
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+
+		emc-tables@1 {
+			nvidia,ram-code = <1>; /* elpida-4gb */
+			reg = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			emc-table@25000 {
+				reg = <25000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <25000>;
+				nvidia,emc-registers = <0x00000002 0x00000006
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000004
+					0x00000003 0x00000008 0x0000000b 0x0000004d
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000068 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x0007c000 0x00000000 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@50000 {
+				reg = <50000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <50000>;
+				nvidia,emc-registers = <0x00000003 0x00000007
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000009f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000007
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x000000d0 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x0007c000 0x00000000 0x00000000 0x00000005
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@75000 {
+				reg = <75000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <75000>;
+				nvidia,emc-registers = <0x00000005 0x0000000a
+					0x00000004 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x000000ff
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x0000000b
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000138 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x0007c000 0x00000000 0x00000000 0x00000007
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@150000 {
+				reg = <150000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <150000>;
+				nvidia,emc-registers = <0x00000009 0x00000014
+					0x00000007 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000021f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000015
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000270 0x00000000 0x00000001
+					0x00000000 0x00000000 0x00000282 0xa07c04ae
+					0x007e4010 0x00000000 0x00000000 0x0000000e
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@300000 {
+				reg = <300000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <300000>;
+				nvidia,emc-registers = <0x00000012 0x00000027
+					0x0000000d 0x00000006 0x00000007 0x00000005
+					0x00000003 0x00000009 0x00000006 0x00000006
+					0x00000003 0x00000003 0x00000002 0x00000006
+					0x00000003 0x00000009 0x0000000c 0x0000045f
+					0x00000000 0x00000004 0x00000004 0x00000006
+					0x00000008 0x00000001 0x0000000e 0x0000002a
+					0x00000003 0x0000000f 0x00000007 0x00000005
+					0x00000002 0x000004e1 0x00000005 0x00000002
+					0x00000000 0x00000000 0x00000282 0xe059048b
+					0x007e0010 0x00000000 0x00000000 0x0000001b
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+
+		emc-tables@2 {
+			nvidia,ram-code = <2>; /* hynix-8gb */
+			reg = <2>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			emc-table@25000 {
+				reg = <25000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <25000>;
+				nvidia,emc-registers = <0x00000002 0x00000006
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000004
+					0x00000003 0x00000008 0x0000000b 0x0000004d
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000068 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@50000 {
+				reg = <50000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <50000>;
+				nvidia,emc-registers = <0x00000003 0x00000007
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000009f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000007
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x000000d0 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000005
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@75000 {
+				reg = <75000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <75000>;
+				nvidia,emc-registers = <0x00000005 0x0000000a
+					0x00000004 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x000000ff
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x0000000b
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000138 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000007
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@150000 {
+				reg = <150000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <150000>;
+				nvidia,emc-registers = <0x00000009 0x00000014
+					0x00000007 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000021f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000015
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000270 0x00000000 0x00000001
+					0x00000000 0x00000000 0x00000282 0xa07c04ae
+					0x007dd010 0x00000000 0x00000000 0x0000000e
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@300000 {
+				reg = <300000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <300000>;
+				nvidia,emc-registers = <0x00000012 0x00000027
+					0x0000000d 0x00000006 0x00000007 0x00000005
+					0x00000003 0x00000009 0x00000006 0x00000006
+					0x00000003 0x00000003 0x00000002 0x00000006
+					0x00000003 0x00000009 0x0000000c 0x0000045f
+					0x00000000 0x00000004 0x00000004 0x00000006
+					0x00000008 0x00000001 0x0000000e 0x0000002a
+					0x00000003 0x0000000f 0x00000007 0x00000005
+					0x00000002 0x000004e1 0x00000005 0x00000002
+					0x00000000 0x00000000 0x00000282 0xe059048b
+					0x007e2010 0x00000000 0x00000000 0x0000001b
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+
+		emc-tables@3 {
+			nvidia,ram-code = <3>; /* hynix-4gb */
+			reg = <3>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			emc-table@25000 {
+				reg = <25000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <25000>;
+				nvidia,emc-registers = <0x00000002 0x00000006
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000004
+					0x00000003 0x00000008 0x0000000b 0x0000004d
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000068 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x0007c000 0x00000000 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@50000 {
+				reg = <50000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <50000>;
+				nvidia,emc-registers = <0x00000003 0x00000007
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000009f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000007
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x000000d0 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x0007c000 0x00078000 0x00000000 0x00000005
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@75000 {
+				reg = <75000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <75000>;
+				nvidia,emc-registers = <0x00000005 0x0000000a
+					0x00000004 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x000000ff
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x0000000b
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000138 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x0007c000 0x00000000 0x00000000 0x00000007
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@150000 {
+				reg = <150000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <150000>;
+				nvidia,emc-registers = <0x00000009 0x00000014
+					0x00000007 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000021f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000015
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000270 0x00000000 0x00000001
+					0x00000000 0x00000000 0x00000282 0xa07c04ae
+					0x007e4010 0x00000000 0x00000000 0x0000000e
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@300000 {
+				reg = <300000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <300000>;
+				nvidia,emc-registers = <0x00000012 0x00000027
+					0x0000000d 0x00000006 0x00000007 0x00000005
+					0x00000003 0x00000009 0x00000006 0x00000006
+					0x00000003 0x00000003 0x00000002 0x00000006
+					0x00000003 0x00000009 0x0000000c 0x0000045f
+					0x00000000 0x00000004 0x00000004 0x00000006
+					0x00000008 0x00000001 0x0000000e 0x0000002a
+					0x00000003 0x0000000f 0x00000007 0x00000005
+					0x00000002 0x000004e1 0x00000005 0x00000002
+					0x00000000 0x00000000 0x00000282 0xe059048b
+					0x007e0010 0x00000000 0x00000000 0x0000001b
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+	};
+
+	usb@c5000000 {
+		compatible = "nvidia,tegra20-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@c5000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+	};
+
+	usb@c5008000 {
+		status = "okay";
+	};
+
+	usb-phy@c5008000 {
+		status = "okay";
+		nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	sdmmc1: mmc@c8000000 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA20_CLK_SDMMC1>;
+		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_1v8_sys>;
+
+		/* Azurewave AW-NH611 BCM4329 */
+		wifi@1 {
+			reg = <1>;
+			compatible = "brcm,bcm4329-fmac";
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc3: mmc@c8000400 {
+		status = "okay";
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		power-gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+	};
+
+	sdmmc4: mmc@c8000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+		non-removable;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_3v3_sys>;
+		pwms = <&pwm 2 41667>;
+
+		brightness-levels = <7 255>;
+		num-interpolated-steps = <248>;
+		default-brightness-level = <20>;
+	};
+
+	bat1010: battery-2s1p {
+		compatible = "simple-battery";
+		charge-full-design-microamp-hours = <3260000>;
+		energy-full-design-microwatt-hours = <24000000>;
+		operating-range-celsius = <0 40>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k-in {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "tps658621-out32k";
+	};
+
+	/*
+	 * This standalone onboard fixed-clock always-ON 32KHz
+	 * oscillator is used as a reference clock-source by the
+	 * Azurewave WiFi/BT module.
+	 */
+	rtc_32k_wifi: clock-32k-wifi {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "kk3270032";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	display-panel {
+		compatible = "auo,b101ew05", "panel-lvds";
+
+		ddc-i2c-bus = <&panel_ddc>;
+		power-supply = <&vdd_pnl>;
+		backlight = <&backlight>;
+
+		width-mm = <218>;
+		height-mm = <135>;
+
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <71200000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <8>;
+			hback-porch = <18>;
+			hsync-len = <184>;
+			vsync-len = <3>;
+			vfront-porch = <4>;
+			vback-porch = <8>;
+		};
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&lvds_encoder_output>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-rotation-lock {
+			label = "Rotate-lock";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_HIGH>;
+			linux,code = <SW_ROTATE_LOCK>;
+			linux,input-type = <EV_SW>;
+			debounce-interval = <10>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		panel_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			embedded-controller@58 {
+				compatible = "acer,a500-iconia-ec", "ene,kb930";
+				reg = <0x58>;
+
+				system-power-controller;
+
+				monitored-battery = <&bat1010>;
+				power-supplies = <&mains>;
+			};
+		};
+	};
+
+	lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+
+		powerdown-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_3v3_sys>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_input: endpoint {
+					remote-endpoint = <&lcd_output>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_output: endpoint {
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-666000000;
+		/delete-node/ opp-760000000;
+	};
+
+	vdd_5v0_sys: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_vs";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_1v8_sys: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_vs";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <300000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-wm8903-picasso",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Acer Iconia Tab A500 WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "LINEOUTL",
+			"Int Spk", "LINEOUTR",
+			"Mic Jack", "MICBIAS",
+			"IN2L", "Mic Jack",
+			"IN2R", "Mic Jack",
+			"IN1L", "Int Mic",
+			"IN1R", "Int Mic";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,int-mic-en-gpios = <&wm8903 1 GPIO_ACTIVE_HIGH>;
+		nvidia,headset;
+
+		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
+			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
+			 <&tegra_car TEGRA20_CLK_CDEV1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+	};
+
+	thermal-zones {
+		/*
+		 * NCT1008 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents A500 from
+		 * getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* start throttling at 60C */
+					temperature = <60000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 70C */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&rtc_32k_wifi>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra20-asus-tf101.dts b/arch/arm/boot/dts/nvidia/tegra20-asus-tf101.dts
new file mode 100644
index 000000000000..e118809dc6d9
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra20-asus-tf101.dts
@@ -0,0 +1,1295 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/atmel-maxtouch.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra20.dtsi"
+#include "tegra20-cpu-opp.dtsi"
+#include "tegra20-cpu-opp-microvolt.dtsi"
+
+/ {
+	model = "ASUS EeePad Transformer TF101";
+	compatible = "asus,tf101", "nvidia,tegra20";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc3; /* MicroSD */
+		mmc2 = &sdmmc1; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd;
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	memory@0 {
+		reg = <0x00000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@2ffe0000 {
+			compatible = "ramoops";
+			reg = <0x2ffe0000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		linux,cma@30000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x30000000 0x10000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+	};
+
+	host1x@50000000 {
+		dc@54200000 {
+			rgb {
+				status = "okay";
+
+				port {
+					lcd_output: endpoint {
+						remote-endpoint = <&lvds_encoder_input>;
+						bus-width = <18>;
+					};
+				};
+			};
+		};
+
+		hdmi@54280000 {
+			status = "okay";
+
+			vdd-supply = <&hdmi_vdd_reg>;
+			pll-supply = <&hdmi_pll_reg>;
+			hdmi-supply = <&vdd_hdmi_en>;
+
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7)
+				GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio@6000d000 {
+		charging-enable-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(R, 6) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000014 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			ata {
+				nvidia,pins = "ata";
+				nvidia,function = "ide";
+			};
+
+			atb {
+				nvidia,pins = "atb", "gma", "gme";
+				nvidia,function = "sdio4";
+			};
+
+			atc {
+				nvidia,pins = "atc";
+				nvidia,function = "nand";
+			};
+
+			atd {
+				nvidia,pins = "atd", "ate", "gmb", "spia",
+					"spib", "spic";
+				nvidia,function = "gmi";
+			};
+
+			cdev1 {
+				nvidia,pins = "cdev1";
+				nvidia,function = "plla_out";
+			};
+
+			cdev2 {
+				nvidia,pins = "cdev2";
+				nvidia,function = "pllp_out4";
+			};
+
+			crtp {
+				nvidia,pins = "crtp";
+				nvidia,function = "crt";
+			};
+
+			lm1 {
+				nvidia,pins = "lm1";
+				nvidia,function = "rsvd3";
+			};
+
+			csus {
+				nvidia,pins = "csus";
+				nvidia,function = "vi_sensor_clk";
+			};
+
+			dap1 {
+				nvidia,pins = "dap1";
+				nvidia,function = "dap1";
+			};
+
+			dap2 {
+				nvidia,pins = "dap2";
+				nvidia,function = "dap2";
+			};
+
+			dap3 {
+				nvidia,pins = "dap3";
+				nvidia,function = "dap3";
+			};
+
+			dap4 {
+				nvidia,pins = "dap4";
+				nvidia,function = "dap4";
+			};
+
+			dta {
+				nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+				nvidia,function = "vi";
+			};
+
+			dtf {
+				nvidia,pins = "dtf";
+				nvidia,function = "i2c3";
+			};
+
+			gmc {
+				nvidia,pins = "gmc";
+				nvidia,function = "uartd";
+			};
+
+			gmd {
+				nvidia,pins = "gmd";
+				nvidia,function = "sflash";
+			};
+
+			gpu {
+				nvidia,pins = "gpu";
+				nvidia,function = "pwm";
+			};
+
+			gpu7 {
+				nvidia,pins = "gpu7";
+				nvidia,function = "rtck";
+			};
+
+			gpv {
+				nvidia,pins = "gpv", "slxa";
+				nvidia,function = "pcie";
+			};
+
+			hdint {
+				nvidia,pins = "hdint";
+				nvidia,function = "hdmi";
+			};
+
+			i2cp {
+				nvidia,pins = "i2cp";
+				nvidia,function = "i2cp";
+			};
+
+			irrx {
+				nvidia,pins = "irrx", "irtx";
+				nvidia,function = "uartb";
+			};
+
+			kbca {
+				nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+					"kbce", "kbcf";
+				nvidia,function = "kbc";
+			};
+
+			lcsn {
+				nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
+					"lsdi", "lvp0";
+				nvidia,function = "rsvd4";
+			};
+
+			ld0 {
+				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+					"ld5", "ld6", "ld7", "ld8", "ld9",
+					"ld10", "ld11", "ld12", "ld13", "ld14",
+					"ld15", "ld16", "ld17", "ldi", "lhp0",
+					"lhp1", "lhp2", "lhs", "lpp", "lpw0",
+					"lpw2", "lsc0", "lsc1", "lsck", "lsda",
+					"lspi", "lvp1", "lvs";
+				nvidia,function = "displaya";
+			};
+
+			owc {
+				nvidia,pins = "owc", "spdi", "spdo", "uac";
+				nvidia,function = "rsvd2";
+			};
+
+			pmc {
+				nvidia,pins = "pmc";
+				nvidia,function = "pwr_on";
+			};
+
+			rm {
+				nvidia,pins = "rm";
+				nvidia,function = "i2c1";
+			};
+
+			sdb {
+				nvidia,pins = "sdb", "sdc", "sdd", "slxc", "slxk";
+				nvidia,function = "sdio3";
+			};
+
+			sdio1 {
+				nvidia,pins = "sdio1";
+				nvidia,function = "sdio1";
+			};
+
+			slxd {
+				nvidia,pins = "slxd";
+				nvidia,function = "spdif";
+			};
+
+			spid {
+				nvidia,pins = "spid", "spie", "spif";
+				nvidia,function = "spi1";
+			};
+
+			spig {
+				nvidia,pins = "spig", "spih";
+				nvidia,function = "spi2_alt";
+			};
+
+			uaa {
+				nvidia,pins = "uaa", "uab", "uda";
+				nvidia,function = "ulpi";
+			};
+
+			uad {
+				nvidia,pins = "uad";
+				nvidia,function = "irda";
+			};
+
+			uca {
+				nvidia,pins = "uca", "ucb";
+				nvidia,function = "uartc";
+			};
+
+			conf_ata {
+				nvidia,pins = "ata", "atb", "atc", "atd",
+					"cdev1", "cdev2", "dap1", "dap4",
+					"dte", "ddc", "dtf", "gma", "gmc",
+					"gme", "gpu", "gpu7", "gpv", "i2cp",
+					"irrx", "irtx", "pta", "rm", "sdc",
+					"sdd", "slxc", "slxd", "slxk", "spdi",
+					"spdo", "uac", "uad",
+					"uda", "csus";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_ate {
+				nvidia,pins = "ate", "dap2", "dap3", "gmb", "gmd",
+					"owc", "spia", "spib", "spic",
+					"spid", "spie", "spig", "slxa";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_ck32 {
+				nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+					"pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+			};
+
+			conf_crtp {
+				nvidia,pins = "crtp", "spih";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_dta {
+				nvidia,pins = "dta", "dtb", "dtc", "dtd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_spif {
+				nvidia,pins = "spif";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_hdint {
+				nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+					"lpw1", "lsck", "lsda", "lsdi", "lvp0";
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_kbca {
+				nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+					"kbce", "kbcf", "sdio1", "uaa", "uab",
+					"uca", "ucb";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_lc {
+				nvidia,pins = "lc", "ls";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+			};
+
+			conf_ld0 {
+				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+					"ld5", "ld6", "ld7", "ld8", "ld9",
+					"ld10", "ld11", "ld12", "ld13", "ld14",
+					"ld15", "ld16", "ld17", "ldi", "lhp0",
+					"lhp1", "lhp2", "lhs", "lm0", "lpp",
+					"lpw0", "lpw2", "lsc0", "lsc1", "lspi",
+					"lvp1", "lvs", "pmc", "sdb";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_ld17_0 {
+				nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+					"ld23_22";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1", "drive_ddc", "drive_vi1";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			drive_csus {
+				nvidia,pins = "drive_csus";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+		};
+
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "i2c2";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "rsvd4";
+			};
+		};
+
+		state_i2cmux_idle: pinmux-i2cmux-idle {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "rsvd4";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "rsvd4";
+			};
+		};
+
+		state_i2cmux_pta: pinmux-i2cmux-pta {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "rsvd4";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "i2c2";
+			};
+		};
+	};
+
+	spdif@70002400 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
+	i2s@70002800 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
+	serial@70006040 {
+		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		/* GPS BCM4751 */
+	};
+
+	serial@70006200 {
+		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			/* PLLP 216MHz / 16 / 4 */
+			max-speed = <3375000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			vbat-supply  = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8_sys>;
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+		status = "okay";
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Aichi AMI306 digital compass */
+		magnetometer@e {
+			compatible = "asahi-kasei,ak8974";
+			reg = <0xe>;
+
+			avdd-supply = <&vdd_3v3_sys>;
+			dvdd-supply = <&vdd_1v8_sys>;
+
+			mount-matrix = "-1",  "0",  "0",
+					"0",  "1",  "0",
+					"0",  "0", "-1";
+		};
+
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_BOTH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0x83>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <
+				0x00000600 /* DMIC_LR, output */
+				0x00000680 /* DMIC_DAT, input */
+				0x00000000 /* Speaker-enable GPIO, output, low */
+				0xffffffff /* don't touch */
+				0xffffffff /* don't touch */
+			>;
+
+			AVDD-supply  = <&vdd_1v8_sys>;
+			CPVDD-supply = <&vdd_1v8_sys>;
+			DBVDD-supply = <&vdd_1v8_sys>;
+			DCVDD-supply = <&vdd_1v8_sys>;
+		};
+
+		/* Atmel MXT1386 Touchscreen */
+		touchscreen@5b {
+			compatible = "atmel,maxtouch";
+			reg = <0x5b>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(V, 6) IRQ_TYPE_LEVEL_LOW>;
+
+			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+
+			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Z, 4) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply    = <&vdd_3v3_sys>;
+			vlogic-supply = <&vdd_1v8_sys>;
+
+			mount-matrix =	 "0",  "1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0",  "1";
+
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0xf>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(N, 4) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_1v8_sys>;
+					vddio-supply = <&vdd_1v8_sys>;
+
+					mount-matrix =	"-1",  "0",  "0",
+							 "0", "-1",  "0",
+							 "0",  "0", "-1";
+				};
+			};
+		};
+	};
+
+	i2c2: i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		pmic: pmic@34 {
+			compatible = "ti,tps6586x";
+			reg = <0x34>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			ti,system-power-controller;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			sys-supply = <&vdd_5v0_sys>;
+			vin-sm0-supply = <&sys_reg>;
+			vin-sm1-supply = <&sys_reg>;
+			vin-sm2-supply = <&sys_reg>;
+			vinldo01-supply = <&sm2_reg>;
+			vinldo23-supply = <&sm2_reg>;
+			vinldo4-supply = <&sm2_reg>;
+			vinldo678-supply = <&sm2_reg>;
+			vinldo9-supply = <&sm2_reg>;
+
+			regulators {
+				sys_reg: sys {
+					regulator-name = "vdd_sys";
+					regulator-always-on;
+				};
+
+				vdd_core: sm0 {
+					regulator-name = "vdd_sm0,vdd_core";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&rtc_vdd &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
+				};
+
+				vdd_cpu: sm1 {
+					regulator-name = "vdd_sm1,vdd_cpu";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-coupled-with = <&vdd_core &rtc_vdd>;
+					regulator-coupled-max-spread = <550000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				sm2_reg: sm2 {
+					regulator-name = "vdd_sm2,vin_ldo*";
+					regulator-min-microvolt = <3700000>;
+					regulator-max-microvolt = <3700000>;
+					regulator-always-on;
+				};
+
+				/* LDO0 is not connected to anything */
+
+				ldo1 {
+					regulator-name = "vdd_ldo1,avdd_pll*";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				rtc_vdd: ldo2 {
+					regulator-name = "vdd_ldo2,vdd_rtc";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&vdd_core &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-rtc-regulator;
+				};
+
+				ldo3 {
+					regulator-name = "vdd_ldo3,avdd_usb*";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_ldo4,avdd_osc,vddio_sys";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				vcore_emmc: ldo5 {
+					regulator-name = "vdd_ldo5,vcore_mmc";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				ldo6 {
+					regulator-name = "vdd_ldo6,avdd_vdac";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				hdmi_vdd_reg: ldo7 {
+					regulator-name = "vdd_ldo7,avdd_hdmi,vdd_fuse";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				hdmi_pll_reg: ldo8 {
+					regulator-name = "vdd_ldo8,avdd_hdmi_pll";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo9 {
+					regulator-name = "vdd_ldo9,avdd_2v85,vdd_ddr_rx";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				ldo_rtc {
+					regulator-name = "vdd_rtc_out,vdd_cell";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+			};
+		};
+
+		nct1008: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+			vcc-supply = <&vdd_3v3_sys>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 6) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	pmc@7000e400 {
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <1>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <100>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <458>;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+	};
+
+	memory-controller@7000f400 {
+		nvidia,use-ram-code;
+
+		emc-tables@3 {
+			reg = <0x3>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			emc-table@25000 {
+				reg = <25000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <25000>;
+				nvidia,emc-registers = <0x00000002 0x00000006
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000004
+					0x00000003 0x00000008 0x0000000b 0x0000004d
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000068 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@50000 {
+				reg = <50000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <50000>;
+				nvidia,emc-registers = <0x00000003 0x00000007
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000009f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000007
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x000000d0 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000005
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@75000 {
+				reg = <75000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <75000>;
+				nvidia,emc-registers = <0x00000005 0x0000000a
+					0x00000004 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x000000ff
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x0000000b
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000138 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000007
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@150000 {
+				reg = <150000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <150000>;
+				nvidia,emc-registers = <0x00000009 0x00000014
+					0x00000007 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000021f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000015
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000270 0x00000000 0x00000001
+					0x00000000 0x00000000 0x00000282 0xa07c04ae
+					0x007dc010 0x00000000 0x00000000 0x0000000e
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@300000 {
+				reg = <300000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <300000>;
+				nvidia,emc-registers = <0x00000012 0x00000027
+					0x0000000d 0x00000006 0x00000007 0x00000005
+					0x00000003 0x00000009 0x00000006 0x00000006
+					0x00000003 0x00000003 0x00000002 0x00000006
+					0x00000003 0x00000009 0x0000000c 0x0000045f
+					0x00000000 0x00000004 0x00000004 0x00000006
+					0x00000008 0x00000001 0x0000000e 0x0000002a
+					0x00000003 0x0000000f 0x00000007 0x00000005
+					0x00000002 0x000004e0 0x00000005 0x00000002
+					0x00000000 0x00000000 0x00000282 0xe059048b
+					0x007e0010 0x00000000 0x00000000 0x0000001b
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			lpddr2 {
+				compatible = "elpida,B8132B2PB-6D-F", "jedec,lpddr2-s4";
+				revision-id = <1 0>;
+				density = <2048>;
+				io-width = <16>;
+			};
+		};
+	};
+
+	/* Peripheral USB via ASUS connector */
+	usb@c5000000 {
+		compatible = "nvidia,tegra20-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@c5000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	/* Dock's USB port */
+	usb@c5008000 {
+		status = "okay";
+	};
+
+	usb-phy@c5008000 {
+		status = "okay";
+		nvidia,xcvr-setup-use-fuses;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	sdmmc1: mmc@c8000000 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA20_CLK_SDMMC1>;
+		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_C>;
+		assigned-clock-rates = <40000000>;
+
+		max-frequency = <40000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+
+		/* Azurewave AW-NH615 BCM4329B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc3: mmc@c8000400 {
+		status = "okay";
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
+		power-gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+	};
+
+	sdmmc4: mmc@c8000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+		non-removable;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_3v3_sys>;
+		pwms = <&pwm 2 4000000>;
+
+		brightness-levels = <7 255>;
+		num-interpolated-steps = <248>;
+		default-brightness-level = <20>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k-in {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	display-panel {
+		compatible = "auo,b101ew05", "panel-lvds";
+
+		/* AUO B101EW05 using custom timings */
+
+		backlight = <&backlight>;
+		ddc-i2c-bus = <&lvds_ddc>;
+		power-supply = <&vdd_pnl_reg>;
+
+		width-mm = <218>;
+		height-mm = <135>;
+
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <71200000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <8>;
+			hback-porch = <18>;
+			hsync-len = <184>;
+			vsync-len = <3>;
+			vfront-porch = <4>;
+			vback-porch = <8>;
+		};
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&lvds_encoder_output>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-dock-hall-sensor {
+			label = "Lid";
+			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&i2c2>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		lvds_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smart-battery@b {
+				compatible = "ti,bq20z75", "sbs,sbs-battery";
+				reg = <0xb>;
+				sbs,i2c-retry-count = <2>;
+				sbs,poll-retry-count = <10>;
+				power-supplies = <&mains>;
+			};
+		};
+	};
+
+	lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+
+		powerdown-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_3v3_sys>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_input: endpoint {
+					remote-endpoint = <&lcd_output>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_output: endpoint {
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-666000000;
+		/delete-node/ opp-760000000;
+	};
+
+	vdd_5v0_sys: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_vs";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	regulator-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie_vdd";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+
+	vdd_pnl_reg: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_pnl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_1v8_sys: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_vs";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_hdmi_en: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_hdmi_en";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+		gpio = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-wm8903-tf101",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Asus EeePad Transformer WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"IN2L", "Mic Jack",
+			"DMICDAT", "Int Mic";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,mic-det-gpios = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_LOW>;
+		nvidia,coupled-mic-hp-det;
+
+		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
+			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
+			 <&tegra_car TEGRA20_CLK_CDEV1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+	};
+
+	thermal-zones {
+		/*
+		 * NCT1008 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents TF101 from
+		 * getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* start throttling at 60C */
+					temperature = <60000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 70C */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+		power-off-delay-us = <200>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts b/arch/arm/boot/dts/nvidia/tegra20-colibri-eval-v3.dts
index 3c0f2681fcde..be2ead4147f2 100644
--- a/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-colibri-eval-v3.dts
@@ -70,11 +70,11 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-a-b {
+			sdc {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-c-d {
+			sdb_sdd {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
@@ -102,6 +102,8 @@
 
 	/* Colibri UART-A */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -143,6 +145,24 @@
 		status = "okay";
 	};
 
+	/* SPI4: Colibri SSP */
+	spi@7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+
+		can@0 {
+			compatible = "microchip,mcp2515";
+			reg = <0>;
+			clocks = <&clk16m>;
+			interrupt-parent = <&gpio>;
+			/* CAN_INT */
+			interrupts = <TEGRA_GPIO(A, 0) IRQ_TYPE_EDGE_FALLING>;
+			spi-max-frequency = <10000000>;
+			vdd-supply = <&reg_3v3>;
+			xceiver-supply = <&reg_5v0>;
+		};
+	};
+
 	/* EHCI instance 0: USB1_DP/N -> USBC_P/N */
 	usb@c5000000 {
 		status = "okay";
@@ -164,26 +184,8 @@
 		vbus-supply = <&reg_usbh_vbus>;
 	};
 
-	/* SPI4: Colibri SSP */
-	spi@7000da00 {
-		status = "okay";
-		spi-max-frequency = <25000000>;
-
-		can@0 {
-			compatible = "microchip,mcp2515";
-			reg = <0>;
-			clocks = <&clk16m>;
-			interrupt-parent = <&gpio>;
-			/* CAN_INT */
-			interrupts = <TEGRA_GPIO(A, 0) IRQ_TYPE_EDGE_FALLING>;
-			spi-max-frequency = <10000000>;
-			vdd-supply = <&reg_3v3>;
-			xceiver-supply = <&reg_5v0>;
-		};
-	};
-
 	/* SD/MMC */
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		status = "okay";
 		bus-width = <4>;
 		cd-gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_LOW>; /* MMCD */
@@ -200,7 +202,7 @@
 		pwms = <&pwm 0 5000000>; /* PWM<A> */
 	};
 
-	clk16m: osc3 {
+	clk16m: clock-osc3 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <16000000>;
@@ -209,7 +211,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
@@ -223,7 +225,7 @@
 		 * edt,et057090dhu: EDT 5.7" LCD TFT
 		 * edt,et070080dh6: EDT 7.0" LCD TFT
 		 */
-		compatible = "edt,et057090dhu", "simple-panel";
+		compatible = "edt,et057090dhu";
 		backlight = <&backlight>;
 		power-supply = <&reg_3v3>;
 	};
diff --git a/arch/arm/boot/dts/tegra20-colibri-iris.dts b/arch/arm/boot/dts/nvidia/tegra20-colibri-iris.dts
index d8004d68efa0..1da202ad1ded 100644
--- a/arch/arm/boot/dts/tegra20-colibri-iris.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-colibri-iris.dts
@@ -70,11 +70,11 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-a-b {
+			sdc {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-c-d {
+			sdb_sdd {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
@@ -102,6 +102,8 @@
 
 	/* Colibri UART-A */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -143,6 +145,12 @@
 		status = "okay";
 	};
 
+	/* SPI4: Colibri SSP */
+	spi@7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+	};
+
 	/* EHCI instance 0: USB1_DP/N -> USBC_P/N */
 	usb@c5000000 {
 		status = "okay";
@@ -164,14 +172,8 @@
 		vbus-supply = <&reg_usbh_vbus>;
 	};
 
-	/* SPI4: Colibri SSP */
-	spi@7000da00 {
-		status = "okay";
-		spi-max-frequency = <25000000>;
-	};
-
 	/* SD/MMC */
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		status = "okay";
 		bus-width = <4>;
 		cd-gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_LOW>; /* MMCD */
@@ -191,7 +193,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
@@ -205,7 +207,7 @@
 		 * edt,et057090dhu: EDT 5.7" LCD TFT
 		 * edt,et070080dh6: EDT 7.0" LCD TFT
 		 */
-		compatible = "edt,et057090dhu", "simple-panel";
+		compatible = "edt,et057090dhu";
 		backlight = <&backlight>;
 		power-supply = <&reg_3v3>;
 	};
diff --git a/arch/arm/boot/dts/tegra20-colibri.dtsi b/arch/arm/boot/dts/nvidia/tegra20-colibri.dtsi
index 6162d193e12c..8c1d5c9fa483 100644
--- a/arch/arm/boot/dts/tegra20-colibri.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-colibri.dtsi
@@ -27,6 +27,31 @@
 		};
 	};
 
+	gpio@6000d000 {
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET#";
+		};
+
+		/* Tri-stating GMI_WR_N on SODIMM pin 99 nPWE */
+		npwe-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "Tri-state nPWE";
+		};
+
+		/* Not tri-stating GMI_WR_N on SODIMM pin 93 RDnWR */
+		rdnwr-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(T, 6) GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "Not tri-state RDnWR";
+		};
+	};
+
 	pinmux@70000014 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -113,7 +138,7 @@
 			};
 
 			/* Colibri Backlight PWM<A>, PWM<B> */
-			pwm-a-b {
+			sdc {
 				nvidia,pins = "sdc";
 				nvidia,function = "pwm";
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -242,7 +267,7 @@
 			};
 
 			/* Colibri PWM<C>, PWM<D> */
-			pwm-c-d {
+			sdb_sdd {
 				nvidia,pins = "sdb", "sdd";
 				nvidia,function = "pwm";
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -421,17 +446,21 @@
 	tegra_ac97: ac97@70002000 {
 		status = "okay";
 		nvidia,codec-reset-gpio =
-			<&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+			<&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 		nvidia,codec-sync-gpio =
 			<&gpio TEGRA_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
 	};
 
 	serial@70006040 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	nand-controller@70008000 {
@@ -495,7 +524,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "VDD_CORE_1.2V";
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
@@ -601,6 +630,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 
 		/* Set SLEEP MODE bit in SUPPLYENE register of TPS658643 PMIC */
 		i2c-thermtrip {
@@ -688,7 +718,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		asix@1 {
+		ethernet@1 {
+			compatible = "usbb95,772b";
 			reg = <1>;
 			local-mac-address = [00 00 00 00 00 00];
 		};
@@ -701,12 +732,16 @@
 		vbus-supply = <&reg_lan_v_bus>;
 	};
 
-	clk32k_in: xtal3 {
+	clk32k_in: clock-xtal3 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
 	};
 
+	opp-table-emc {
+		/delete-node/ opp-760000000;
+	};
+
 	reg_lan_v_bus: regulator-lan-v-bus {
 		compatible = "regulator-fixed";
 		regulator-name = "LAN_V_BUS";
@@ -741,28 +776,3 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };
-
-&gpio {
-	lan-reset-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET#";
-	};
-
-	/* Tri-stating GMI_WR_N on SODIMM pin 99 nPWE */
-	npwe {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "Tri-state nPWE";
-	};
-
-	/* Not tri-stating GMI_WR_N on SODIMM pin 93 RDnWR */
-	rdnwr {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(T, 6) GPIO_ACTIVE_HIGH>;
-		output-low;
-		line-name = "Not tri-state RDnWR";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp-microvolt.dtsi
index e85ffdbef876..7330c1b13d93 100644
--- a/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp-microvolt.dtsi
@@ -1,200 +1,164 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	cpu0_opp_table: cpu_opp_table0 {
-		opp@216000000_750 {
+	cpu0_opp_table: opp-table-cpu0 {
+		opp-216000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@216000000_800 {
+		opp-216000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@312000000_750 {
+		opp-312000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@312000000_800 {
+		opp-312000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@456000000_750 {
+		opp-456000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@456000000_800 {
+		opp-456000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@456000000_800_2_2 {
-			opp-microvolt = <800000 800000 1125000>;
-		};
-
-		opp@456000000_800_3_2 {
-			opp-microvolt = <800000 800000 1125000>;
-		};
-
-		opp@456000000_825 {
+		opp-456000000-825 {
 			opp-microvolt = <825000 825000 1125000>;
 		};
 
-		opp@608000000_750 {
+		opp-608000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@608000000_800 {
-			opp-microvolt = <800000 800000 1125000>;
-		};
-
-		opp@608000000_800_3_2 {
+		opp-608000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@608000000_825 {
+		opp-608000000-825 {
 			opp-microvolt = <825000 825000 1125000>;
 		};
 
-		opp@608000000_850 {
+		opp-608000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@608000000_900 {
+		opp-608000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@760000000_775 {
+		opp-760000000-775 {
 			opp-microvolt = <775000 775000 1125000>;
 		};
 
-		opp@760000000_800 {
+		opp-760000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@760000000_850 {
+		opp-760000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@760000000_875 {
+		opp-760000000-875 {
 			opp-microvolt = <875000 875000 1125000>;
 		};
 
-		opp@760000000_875_1_1 {
-			opp-microvolt = <875000 875000 1125000>;
-		};
-
-		opp@760000000_875_0_2 {
-			opp-microvolt = <875000 875000 1125000>;
-		};
-
-		opp@760000000_875_1_2 {
-			opp-microvolt = <875000 875000 1125000>;
-		};
-
-		opp@760000000_900 {
+		opp-760000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@760000000_975 {
+		opp-760000000-975 {
 			opp-microvolt = <975000 975000 1125000>;
 		};
 
-		opp@816000000_800 {
+		opp-816000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@816000000_850 {
+		opp-816000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@816000000_875 {
+		opp-816000000-875 {
 			opp-microvolt = <875000 875000 1125000>;
 		};
 
-		opp@816000000_950 {
+		opp-816000000-950 {
 			opp-microvolt = <950000 950000 1125000>;
 		};
 
-		opp@816000000_1000 {
+		opp-816000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@912000000_850 {
+		opp-912000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@912000000_900 {
+		opp-912000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@912000000_925 {
+		opp-912000000-925 {
 			opp-microvolt = <925000 925000 1125000>;
 		};
 
-		opp@912000000_950 {
-			opp-microvolt = <950000 950000 1125000>;
-		};
-
-		opp@912000000_950_0_2 {
+		opp-912000000-950 {
 			opp-microvolt = <950000 950000 1125000>;
 		};
 
-		opp@912000000_950_2_2 {
-			opp-microvolt = <950000 950000 1125000>;
-		};
-
-		opp@912000000_1000 {
+		opp-912000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@912000000_1050 {
+		opp-912000000-1050 {
 			opp-microvolt = <1050000 1050000 1125000>;
 		};
 
-		opp@1000000000_875 {
+		opp-1000000000-875 {
 			opp-microvolt = <875000 875000 1125000>;
 		};
 
-		opp@1000000000_900 {
+		opp-1000000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@1000000000_950 {
+		opp-1000000000-950 {
 			opp-microvolt = <950000 950000 1125000>;
 		};
 
-		opp@1000000000_975 {
+		opp-1000000000-975 {
 			opp-microvolt = <975000 975000 1125000>;
 		};
 
-		opp@1000000000_1000 {
-			opp-microvolt = <1000000 1000000 1125000>;
-		};
-
-		opp@1000000000_1000_0_2 {
+		opp-1000000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@1000000000_1025 {
+		opp-1000000000-1025 {
 			opp-microvolt = <1025000 1025000 1125000>;
 		};
 
-		opp@1000000000_1100 {
+		opp-1000000000-1100 {
 			opp-microvolt = <1100000 1100000 1125000>;
 		};
 
-		opp@1200000000_1000 {
+		opp-1200000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@1200000000_1050 {
+		opp-1200000000-1050 {
 			opp-microvolt = <1050000 1050000 1125000>;
 		};
 
-		opp@1200000000_1100 {
+		opp-1200000000-1100 {
 			opp-microvolt = <1100000 1100000 1125000>;
 		};
 
-		opp@1200000000_1125 {
+		opp-1200000000-1125 {
 			opp-microvolt = <1125000 1125000 1125000>;
 		};
 	};
diff --git a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp.dtsi
index c878f4231791..47c8e78ca958 100644
--- a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp.dtsi
@@ -1,299 +1,250 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	cpu0_opp_table: cpu_opp_table0 {
+	cpu0_opp_table: opp-table-cpu0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp@216000000_750 {
+		opp-216000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0003>;
 			opp-hz = /bits/ 64 <216000000>;
+			opp-suspend;
 		};
 
-		opp@216000000_800 {
+		opp-216000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0004>;
 			opp-hz = /bits/ 64 <216000000>;
+			opp-suspend;
 		};
 
-		opp@312000000_750 {
+		opp-312000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0003>;
 			opp-hz = /bits/ 64 <312000000>;
 		};
 
-		opp@312000000_800 {
+		opp-312000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0004>;
 			opp-hz = /bits/ 64 <312000000>;
 		};
 
-		opp@456000000_750 {
+		opp-456000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0C 0x0003>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@456000000_800 {
+		opp-456000000-800 {
 			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x03 0x0006>;
-			opp-hz = /bits/ 64 <456000000>;
-		};
-
-		opp@456000000_800_2_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x04 0x0004>;
+			opp-supported-hw = <0x03 0x0006>, <0x04 0x0004>,
+					   <0x08 0x0004>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@456000000_800_3_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <456000000>;
-		};
-
-		opp@456000000_825 {
+		opp-456000000-825 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@608000000_750 {
+		opp-608000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0003>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000_800 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x04 0x0006>;
-			opp-hz = /bits/ 64 <608000000>;
-		};
-
-		opp@608000000_800_3_2 {
+		opp-608000000-800 {
 			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x08 0x0004>;
+			opp-supported-hw = <0x04 0x0006>, <0x08 0x0004>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000_825 {
+		opp-608000000-825 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000_850 {
+		opp-608000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0006>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000_900 {
+		opp-608000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@760000000_775 {
+		opp-760000000-775 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0003>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000_800 {
+		opp-760000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0004>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000_850 {
+		opp-760000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0006>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000_875 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x04 0x0001>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_875_1_1 {
+		opp-760000000-875 {
 			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x02 0x0002>;
+			opp-supported-hw = <0x04 0x0001>, <0x02 0x0002>,
+					   <0x01 0x0004>, <0x02 0x0004>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000_875_0_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x01 0x0004>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_875_1_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x02 0x0004>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900 {
+		opp-760000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0002>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000_975 {
+		opp-760000000-975 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@816000000_800 {
+		opp-816000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0007>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000_850 {
+		opp-816000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0002>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000_875 {
+		opp-816000000-875 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0005>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000_950 {
+		opp-816000000-950 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0006>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000_1000 {
+		opp-816000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@912000000_850 {
+		opp-912000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0007>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000_900 {
+		opp-912000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0002>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000_925 {
+		opp-912000000-925 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000_950 {
+		opp-912000000-950 {
 			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x02 0x0006>;
+			opp-supported-hw = <0x02 0x0006>, <0x01 0x0004>,
+					   <0x04 0x0004>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000_950_0_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x01 0x0004>;
-			opp-hz = /bits/ 64 <912000000>;
-		};
-
-		opp@912000000_950_2_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <912000000>;
-		};
-
-		opp@912000000_1000 {
+		opp-912000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0002>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000_1050 {
+		opp-912000000-1050 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@1000000000_875 {
+		opp-1000000000-875 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0007>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000_900 {
+		opp-1000000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0002>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000_950 {
+		opp-1000000000-950 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0004>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000_975 {
+		opp-1000000000-975 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000_1000 {
+		opp-1000000000-1000 {
 			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x02 0x0006>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_1000_0_2 {
-			clock-latency-ns = <400000>;
-			opp-supported-hw = <0x01 0x0004>;
+			opp-supported-hw = <0x02 0x0006>, <0x01 0x0004>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000_1025 {
+		opp-1000000000-1025 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0002>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000_1100 {
+		opp-1000000000-1100 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1200000000_1000 {
+		opp-1200000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000_1050 {
+		opp-1200000000-1050 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000_1100 {
+		opp-1200000000-1100 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x02 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000_1125 {
+		opp-1200000000-1125 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
diff --git a/arch/arm/boot/dts/tegra20-harmony.dts b/arch/arm/boot/dts/nvidia/tegra20-harmony.dts
index 1d96d92b72a7..5c31a6c8dabe 100644
--- a/arch/arm/boot/dts/tegra20-harmony.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-harmony.dts
@@ -273,6 +273,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -339,7 +341,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
@@ -565,6 +567,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	pcie@80003000 {
@@ -595,8 +598,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -613,7 +614,7 @@
 		status = "okay";
 	};
 
-	sdhci@c8000200 {
+	mmc@c8000200 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
@@ -621,7 +622,7 @@
 		bus-width = <4>;
 	};
 
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
@@ -640,23 +641,16 @@
 		default-brightness-level = <6>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -665,7 +659,7 @@
 	};
 
 	panel: panel {
-		compatible = "auo,b101aw03", "simple-panel";
+		compatible = "auo,b101aw03";
 
 		power-supply = <&vdd_pnl_reg>;
 		enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
@@ -673,79 +667,66 @@
 		backlight = <&backlight>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_5v0_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd_5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vdd_1v5";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v5";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+	};
 
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vdd_1v2";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		pci_vdd_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vdd_1v05";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	pci_vdd_reg: regulator-1v05 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v05";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_pnl_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "vdd_pnl";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_pnl_reg: regulator-pn1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_pnl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_bl_reg: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "vdd_bl";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_bl_reg: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_5v0_hdmi: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "VDDIO_HDMI";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(T, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_reg>;
-		};
+	vdd_5v0_hdmi: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_HDMI";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(T, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_reg>;
 	};
 
 	sound {
@@ -768,7 +749,7 @@
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
-			GPIO_ACTIVE_HIGH>;
+			GPIO_ACTIVE_LOW>;
 		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(X, 0)
 			GPIO_ACTIVE_HIGH>;
 		nvidia,ext-mic-en-gpios = <&gpio TEGRA_GPIO(X, 1)
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/nvidia/tegra20-medcom-wide.dts
index cda5448c2ace..8c657182fff3 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-medcom-wide.dts
@@ -15,10 +15,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	pwm@7000a000 {
-		status = "okay";
-	};
-
 	host1x@50000000 {
 		dc@54200000 {
 			rgb {
@@ -28,6 +24,10 @@
 		};
 	};
 
+	pwm@7000a000 {
+		status = "okay";
+	};
+
 	i2c@7000c000 {
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";
@@ -54,12 +54,15 @@
 
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
+
+		/* close enough */
+		power-supply = <&vdd_3v3_reg>;
 	};
 
 	panel: panel {
-		compatible = "innolux,n156bge-l21", "simple-panel";
+		compatible = "innolux,n156bge-l21";
 
-		power-supply =  <&vdd_1v8_reg>, <&vdd_3v3_reg>;
+		power-supply =  <&vdd_1v8_reg>; // <&vdd_3v3_reg>;
 		enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
 
 		backlight = <&backlight>;
@@ -84,7 +87,7 @@
 		nvidia,audio-codec = <&wm8903>;
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
 
 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
@@ -92,44 +95,38 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	regulators {
-		vcc_24v_reg: regulator@100 {
-			compatible = "regulator-fixed";
-			reg = <100>;
-			regulator-name = "vcc_24v";
-			regulator-min-microvolt = <24000000>;
-			regulator-max-microvolt = <24000000>;
-			regulator-always-on;
-		};
+	vcc_24v_reg: regulator-24v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_24v";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+		regulator-always-on;
+	};
 
-		vdd_5v0_reg: regulator@101 {
-			compatible = "regulator-fixed";
-			reg = <101>;
-			regulator-name = "vdd_5v0";
-			vin-supply = <&vcc_24v_reg>;
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		vin-supply = <&vcc_24v_reg>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		vdd_3v3_reg: regulator@102 {
-			compatible = "regulator-fixed";
-			reg = <102>;
-			regulator-name = "vdd_3v3";
-			vin-supply = <&vcc_24v_reg>;
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	vdd_3v3_reg: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		vin-supply = <&vcc_24v_reg>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		vdd_1v8_reg: regulator@103 {
-			compatible = "regulator-fixed";
-			reg = <103>;
-			regulator-name = "vdd_1v8";
-			vin-supply = <&vdd_3v3_reg>;
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
+	vdd_1v8_reg: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8";
+		vin-supply = <&vdd_3v3_reg>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
index 85fce5bc72d6..afb922bd79a7 100644
--- a/arch/arm/boot/dts/tegra20-paz00.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
 #include "tegra20.dtsi"
 #include "tegra20-cpu-opp.dtsi"
 #include "tegra20-cpu-opp-microvolt.dtsi"
@@ -11,6 +13,8 @@
 	compatible = "compal,paz00", "nvidia,tegra20";
 
 	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* MicroSD */
 		rtc0 = "/i2c@7000d000/tps6586x@34";
 		rtc1 = "/rtc@7000e000";
 		serial0 = &uarta;
@@ -262,15 +266,27 @@
 		};
 	};
 
+	spdif@70002400 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
 	i2s@70002800 {
 		status = "okay";
+
+		nvidia,fixed-parent-rate;
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
 	serial@70006200 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -295,20 +311,19 @@
 		clock-frequency = <100000>;
 	};
 
-	nvec@7000c500 {
+	i2c@7000c500 {
 		compatible = "nvidia,nvec";
-		reg = <0x7000c500 0x100>;
-		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
+
+		/delete-property/ #address-cells;
+		/delete-property/ #size-cells;
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+
 		clock-frequency = <80000>;
 		request-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
 		slave-addr = <138>;
-		clocks = <&tegra_car TEGRA20_CLK_I2C3>,
-			 <&tegra_car TEGRA20_CLK_PLL_P_OUT3>;
-		clock-names = "div-clk", "fast-clk";
-		resets = <&tegra_car 67>;
-		reset-names = "i2c";
+
+		status = "okay";
 	};
 
 	i2c@7000d000 {
@@ -341,10 +356,10 @@
 
 				core_vdd_reg: sm0 {
 					regulator-name = "+1.2vs_sm0,vdd_core";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1225000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
 					regulator-coupled-with = <&rtc_vdd_reg &cpu_vdd_reg>;
-					regulator-coupled-max-spread = <170000 450000>;
+					regulator-coupled-max-spread = <170000 550000>;
 					regulator-always-on;
 
 					nvidia,tegra-core-regulator;
@@ -355,7 +370,7 @@
 					regulator-min-microvolt = <750000>;
 					regulator-max-microvolt = <1100000>;
 					regulator-coupled-with = <&core_vdd_reg &rtc_vdd_reg>;
-					regulator-coupled-max-spread = <450000 450000>;
+					regulator-coupled-max-spread = <550000 550000>;
 					regulator-always-on;
 
 					nvidia,tegra-cpu-regulator;
@@ -379,10 +394,10 @@
 
 				rtc_vdd_reg: ldo2 {
 					regulator-name = "+1.2vs_ldo2,vdd_rtc";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1225000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
 					regulator-coupled-with = <&core_vdd_reg &cpu_vdd_reg>;
-					regulator-coupled-max-spread = <170000 450000>;
+					regulator-coupled-max-spread = <170000 550000>;
 					regulator-always-on;
 
 					nvidia,tegra-rtc-regulator;
@@ -451,9 +466,14 @@
 			};
 		};
 
-		adt7461@4c {
+		adt7461: temperature-sensor@4c {
 			compatible = "adi,adt7461";
 			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 6) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
 		};
 	};
 
@@ -465,6 +485,54 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&core_vdd_reg>;
+	};
+
+	memory-controller@7000f400 {
+		nvidia,use-ram-code;
+
+		emc-tables@0 {
+			nvidia,ram-code = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			emc-table@166500 {
+				reg = <166500>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <166500>;
+				nvidia,emc-registers = <0x0000000a 0x00000016
+					0x00000008 0x00000003 0x00000004 0x00000004
+					0x00000002 0x0000000c 0x00000003 0x00000003
+					0x00000002 0x00000001 0x00000004 0x00000005
+					0x00000004 0x00000009 0x0000000d 0x000004df
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000003 0x00000001 0x0000000a 0x000000c8
+					0x00000003 0x00000006 0x00000004 0x00000008
+					0x00000002 0x00000000 0x00000000 0x00000002
+					0x00000000 0x00000000 0x00000083 0xe03b0323
+					0x007fe010 0x00001414 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@333000 {
+				reg = <333000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <333000>;
+				nvidia,emc-registers = <0x00000018 0x00000033
+					0x00000012 0x00000004 0x00000004 0x00000005
+					0x00000003 0x0000000c 0x00000006 0x00000006
+					0x00000003 0x00000001 0x00000004 0x00000005
+					0x00000004 0x00000009 0x0000000d 0x00000bff
+					0x00000000 0x00000003 0x00000003 0x00000006
+					0x00000006 0x00000001 0x00000011 0x000000c8
+					0x00000003 0x0000000e 0x00000007 0x00000008
+					0x00000002 0x00000000 0x00000000 0x00000002
+					0x00000000 0x00000000 0x00000083 0xf0440303
+					0x007fe010 0x00001414 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
 	};
 
 	usb@c5000000 {
@@ -479,8 +547,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 0)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -497,7 +563,7 @@
 		status = "okay";
 	};
 
-	sdhci@c8000000 {
+	sdmmc1: mmc@c8000000 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
@@ -505,7 +571,7 @@
 		bus-width = <4>;
 	};
 
-	sdhci@c8000600 {
+	sdmmc4: mmc@c8000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -520,26 +586,34 @@
 		brightness-levels = <0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 255>;
 		default-brightness-level = <10>;
 
-		backlight-boot-off;
+		/* close enough */
+		power-supply = <&vdd_pnl_reg>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
 
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&cpu_vdd_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&cpu_vdd_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "Wakeup";
 			gpios = <&gpio TEGRA_GPIO(J, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -550,15 +624,19 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		wifi {
+		led-0 {
 			label = "wifi-led";
 			gpios = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "rfkill0";
 		};
 	};
 
+	opp-table-emc {
+		/delete-node/ opp-760000000;
+	};
+
 	panel: panel {
-		compatible = "samsung,ltn101nt05", "simple-panel";
+		compatible = "samsung,ltn101nt05";
 
 		ddc-i2c-bus = <&lvds_ddc>;
 		power-supply = <&vdd_pnl_reg>;
@@ -567,30 +645,22 @@
 		backlight = <&backlight>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		p5valw_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "+5valw";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	p5valw_reg: regulator-5v0alw {
+		compatible = "regulator-fixed";
+		regulator-name = "+5valw";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		vdd_pnl_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "+3VS,vdd_pnl";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-boot-on;
-			gpio = <&gpio TEGRA_GPIO(A, 4) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_pnl_reg: regulator-3v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "+3VS,vdd_pnl";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(A, 4) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
@@ -619,15 +689,36 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	cpus {
-		cpu0: cpu@0 {
-			cpu-supply = <&cpu_vdd_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <500>; /* milliseconds */
+			polling-delay = <1500>; /* milliseconds */
 
-		cpu@1 {
-			cpu-supply = <&cpu_vdd_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
+			thermal-sensors = <&adt7461 1>;
+
+			trips {
+				trip0: cpu-alert0 {
+					/* start throttling at 80C */
+					temperature = <80000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: cpu-crit {
+					/* shut down at 85C */
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra20-peripherals-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra20-peripherals-opp.dtsi
new file mode 100644
index 000000000000..1b808233a933
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra20-peripherals-opp.dtsi
@@ -0,0 +1,1022 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	core_opp_table: opp-table-core {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		core_opp_950: opp-950000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-level = <950000>;
+		};
+
+		core_opp_1000: opp-1000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-level = <1000000>;
+		};
+
+		core_opp_1100: opp-1100000 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-level = <1100000>;
+		};
+
+		core_opp_1200: opp-1200000 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-level = <1200000>;
+		};
+
+		core_opp_1225: opp-1225000 {
+			opp-microvolt = <1225000 1225000 1300000>;
+			opp-level = <1225000>;
+		};
+
+		core_opp_1275: opp-1275000 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-level = <1275000>;
+		};
+
+		core_opp_1300: opp-1300000 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-level = <1300000>;
+		};
+	};
+
+	emc_icc_dvfs_opp_table: opp-table-emc {
+		compatible = "operating-points-v2";
+
+		opp-36000000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <36000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-47500000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <47500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-50000000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <50000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-54000000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <54000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-57000000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <57000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-100000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-108000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <108000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-126666000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <126666000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-150000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <150000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-216000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <216000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+			opp-suspend;
+		};
+
+		opp-300000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-333000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <333000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-380000000 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-600000000 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-666000000 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <666000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-760000000 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <760000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1300>;
+		};
+	};
+
+	host1x_dvfs_opp_table: opp-table-host1x {
+		compatible = "operating-points-v2";
+
+		opp-104500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <104500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-133000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-166000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <166000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	mpe_dvfs_opp_table: opp-table-mpe {
+		compatible = "operating-points-v2";
+
+		opp-104500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <104500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-142500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <142500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-152000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-228000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <228000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-228000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <228000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-237500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <237500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-266000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <266000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-275500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <275500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	vi_dvfs_opp_table: opp-table-vi {
+		compatible = "operating-points-v2";
+
+		opp-85000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <85000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-100000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-150000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <150000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	epp_dvfs_opp_table: opp-table-epp {
+		compatible = "operating-points-v2";
+
+		opp-133000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-171000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	gr2d_dvfs_opp_table: opp-table-gr2d {
+		compatible = "operating-points-v2";
+
+		opp-133000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-171000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	gr3d_dvfs_opp_table: opp-table-gr3d {
+		compatible = "operating-points-v2";
+
+		opp-114000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <114000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-161500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <161500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-161500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <161500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-209000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <209000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-218500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <218500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-247000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-247000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-256500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <256500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-285000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-304000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-323000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <323000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-333500000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-333500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-351500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <351500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-380000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-400000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-400000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	disp1_dvfs_opp_table: opp-table-disp1 {
+		compatible = "operating-points-v2";
+
+		opp-158000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <158000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-190000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	disp2_dvfs_opp_table: opp-table-disp2 {
+		compatible = "operating-points-v2";
+
+		opp-158000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <158000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-190000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	dsi_dvfs_opp_table: opp-table-dsi {
+		compatible = "operating-points-v2";
+
+		opp-100000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-500000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	hdmi_dvfs_opp_table: opp-table-hdmi {
+		compatible = "operating-points-v2";
+
+		opp-148500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <148500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	tvo_dvfs_opp_table: opp-table-tvo {
+		compatible = "operating-points-v2";
+
+		opp-250000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <250000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sclk_dvfs_opp_table: opp-table-sclk {
+		compatible = "operating-points-v2";
+
+		opp-95000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <95000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-123500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <123500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-133000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-152000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-159500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <159500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-171000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-180500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <180500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-207000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <207000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-218500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <218500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-222500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <222500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-229500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <229500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-240000000-1225 {
+			opp-microvolt = <1225000 1225000 1300000>;
+			opp-hz = /bits/ 64 <240000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1225>;
+		};
+
+		opp-240000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <240000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-247000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-256500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <256500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-260000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <260000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-262000000-1300 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <262000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-264000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-277500000-1300 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <277500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-285000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-292500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <292500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1300 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-300000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1275>;
+		};
+	};
+
+	vde_dvfs_opp_table: opp-table-vde {
+		compatible = "operating-points-v2";
+
+		opp-95000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <95000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-123500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <123500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-123500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <123500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-152000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-152000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-171000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-209000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <209000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-209000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <209000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-218500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <218500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-237500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <237500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-275500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <275500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-285000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	ndflash_dvfs_opp_table: opp-table-ndflash {
+		compatible = "operating-points-v2";
+
+		opp-130000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <130000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-150000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <150000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-158000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <158000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-164000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <164000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	nor_dvfs_opp_table: opp-table-nor {
+		compatible = "operating-points-v2";
+
+		opp-92000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <92000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc1_dvfs_opp_table: opp-table-sdmmc1 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc2_dvfs_opp_table: opp-table-sdmmc2 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc3_dvfs_opp_table: opp-table-sdmmc3 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc4_dvfs_opp_table: opp-table-sdmmc4 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	pcie_dvfs_opp_table: opp-table-pcie {
+		compatible = "operating-points-v2";
+
+		opp-250000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <250000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	usbd_dvfs_opp_table: opp-table-usbd {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	usb2_dvfs_opp_table: opp-table-usb2 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	usb3_dvfs_opp_table: opp-table-usb3 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra20-plutux.dts b/arch/arm/boot/dts/nvidia/tegra20-plutux.dts
index 429e4605fbdb..71a8236491df 100644
--- a/arch/arm/boot/dts/tegra20-plutux.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-plutux.dts
@@ -52,7 +52,7 @@
 		nvidia,audio-codec = <&wm8903>;
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
 
 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
@@ -60,44 +60,38 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	regulators {
-		vcc_24v_reg: regulator@100 {
-			compatible = "regulator-fixed";
-			reg = <100>;
-			regulator-name = "vcc_24v";
-			regulator-min-microvolt = <24000000>;
-			regulator-max-microvolt = <24000000>;
-			regulator-always-on;
-		};
+	vcc_24v_reg: regulator-24v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_24v";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+		regulator-always-on;
+	};
 
-		vdd_5v0_reg: regulator@101 {
-			compatible = "regulator-fixed";
-			reg = <101>;
-			regulator-name = "vdd_5v0";
-			vin-supply = <&vcc_24v_reg>;
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		vin-supply = <&vcc_24v_reg>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		vdd_3v3_reg: regulator@102 {
-			compatible = "regulator-fixed";
-			reg = <102>;
-			regulator-name = "vdd_3v3";
-			vin-supply = <&vcc_24v_reg>;
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	vdd_3v3_reg: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		vin-supply = <&vcc_24v_reg>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		vdd_1v8_reg: regulator@103 {
-			compatible = "regulator-fixed";
-			reg = <103>;
-			regulator-name = "vdd_1v8";
-			vin-supply = <&vdd_3v3_reg>;
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
+	vdd_1v8_reg: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8";
+		vin-supply = <&vdd_3v3_reg>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra20-seaboard.dts b/arch/arm/boot/dts/nvidia/tegra20-seaboard.dts
index f91441683aad..e944ae9b86c2 100644
--- a/arch/arm/boot/dts/tegra20-seaboard.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-seaboard.dts
@@ -285,7 +285,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -296,25 +296,25 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -324,6 +324,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -358,7 +360,7 @@
 		};
 
 		gyrometer@68 {
-			compatible = "invn,mpu3050";
+			compatible = "invensense,mpu3050";
 			reg = <0x68>;
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(Z, 4) IRQ_TYPE_LEVEL_HIGH>;
@@ -370,38 +372,6 @@
 		clock-frequency = <100000>;
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		lvds_ddc: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			smart-battery@b {
-				compatible = "ti,bq20z75", "smart-battery-1.1";
-				reg = <0xb>;
-				ti,i2c-retry-count = <2>;
-				ti,poll-retry-count = <10>;
-			};
-		};
-	};
-
 	i2c@7000c500 {
 		status = "okay";
 		clock-frequency = <400000>;
@@ -444,7 +414,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
 					regulator-min-microvolt = <1300000>;
 					regulator-max-microvolt = <1300000>;
@@ -689,6 +659,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	memory-controller@7000f400 {
@@ -742,8 +713,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -760,14 +729,14 @@
 		status = "okay";
 	};
 
-	sdhci@c8000000 {
+	mmc@c8000000 {
 		status = "okay";
 		power-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
 		bus-width = <4>;
 		keep-power-in-suspend;
 	};
 
-	sdhci@c8000400 {
+	mmc@c8000400 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
@@ -775,7 +744,7 @@
 		bus-width = <4>;
 	};
 
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -792,30 +761,23 @@
 		default-brightness-level = <6>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
 			linux,input-type = <5>; /* EV_SW */
@@ -825,8 +787,40 @@
 		};
 	};
 
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		lvds_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smart-battery@b {
+				compatible = "ti,bq20z75", "sbs,sbs-battery";
+				reg = <0xb>;
+				sbs,i2c-retry-count = <2>;
+				sbs,poll-retry-count = <10>;
+			};
+		};
+	};
+
 	panel: panel {
-		compatible = "chunghwa,claa101wa01a", "simple-panel";
+		compatible = "chunghwa,claa101wa01a";
 
 		power-supply = <&vdd_pnl_reg>;
 		enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
@@ -835,81 +829,68 @@
 		ddc-i2c-bus = <&lvds_ddc>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_5v0_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd_5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vdd_1v5";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v5";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+	};
 
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vdd_1v2";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vbus_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vdd_vbus_wup1";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(D, 0) 0>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
+	vbus_reg: regulator-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbus_wup1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(D, 0) 0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 
-		vdd_pnl_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "vdd_pnl";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_pnl_reg: regulator-pnl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_pnl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_bl_reg: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "vdd_bl";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_bl_reg: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_hdmi: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "VDDIO_HDMI";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_reg>;
-		};
+	vdd_hdmi: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_HDMI";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_reg>;
 	};
 
 	sound {
@@ -931,7 +912,7 @@
 		nvidia,audio-codec = <&wm8903>;
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_LOW>;
 
 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
diff --git a/arch/arm/boot/dts/tegra20-tamonten.dtsi b/arch/arm/boot/dts/nvidia/tegra20-tamonten.dtsi
index 20137fc578b1..5c214dd060bb 100644
--- a/arch/arm/boot/dts/tegra20-tamonten.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-tamonten.dtsi
@@ -183,10 +183,11 @@
 			};
 			conf_ata {
 				nvidia,pins = "ata", "atb", "atc", "atd", "ate",
-					"cdev1", "cdev2", "dap1", "dtb", "gma",
-					"gmb", "gmc", "gmd", "gme", "gpu7",
-					"gpv", "i2cp", "pta", "rm", "slxa",
-					"slxk", "spia", "spib", "uac";
+					"cdev1", "cdev2", "dap1", "dtb", "dtf",
+					"gma", "gmb", "gmc", "gmd", "gme", "gpu7",
+					"gpv", "i2cp", "irrx", "irtx", "pta",
+					"rm", "slxa", "slxk", "spia", "spib",
+					"uac";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
@@ -202,7 +203,7 @@
 			};
 			conf_crtp {
 				nvidia,pins = "crtp", "dap2", "dap3", "dap4",
-					"dtc", "dte", "dtf", "gpu", "sdio1",
+					"dtc", "dte", "gpu", "sdio1",
 					"slxc", "slxd", "spdi", "spdo", "spig",
 					"uda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -211,7 +212,7 @@
 			conf_ddc {
 				nvidia,pins = "ddc", "dta", "dtd", "kbca",
 					"kbcb", "kbcc", "kbcd", "kbce", "kbcf",
-					"sdc";
+					"sdc", "uad", "uca";
 				nvidia,pull = <TEGRA_PIN_PULL_UP>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
@@ -221,10 +222,9 @@
 					"lvp0", "owc", "sdb";
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
-			conf_irrx {
-				nvidia,pins = "irrx", "irtx", "sdd", "spic",
-					"spie", "spih", "uaa", "uab", "uad",
-					"uca", "ucb";
+			conf_sdd {
+				nvidia,pins = "sdd", "spic", "spie", "spih",
+					"uaa", "uab", "ucb";
 				nvidia,pull = <TEGRA_PIN_PULL_UP>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
@@ -249,7 +249,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -260,25 +260,25 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -288,6 +288,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -301,31 +303,6 @@
 		status = "okay";
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
 	i2c@7000d000 {
 		clock-frequency = <400000>;
 		status = "okay";
@@ -357,7 +334,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sys_sm0,vdd_core";
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
@@ -477,6 +454,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	pcie@80003000 {
@@ -495,40 +473,50 @@
 		status = "okay";
 	};
 
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		cd-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
 		bus-width = <4>;
 		status = "okay";
 	};
 
-	clocks {
-		compatible = "simple-bus";
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
-	};
+		i2c-parent = <&{/i2c@7000c400}>;
 
-	regulators {
-		compatible = "simple-bus";
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
 
-		#address-cells = <1>;
-		#size-cells = <0>;
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
 
-		pci_vdd_reg: regulator@1 {
-			compatible = "regulator-fixed";
+		i2c@1 {
 			reg = <1>;
-			regulator-name = "vdd_1v05";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			gpio = <&pmic 2 0>;
-			enable-active-high;
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 	};
+
+	pci_vdd_reg: regulator-1v05 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v05";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		gpio = <&pmic 2 0>;
+		enable-active-high;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra20-tec.dts b/arch/arm/boot/dts/nvidia/tegra20-tec.dts
index 4dec27737238..4f41c74384b2 100644
--- a/arch/arm/boot/dts/tegra20-tec.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-tec.dts
@@ -61,7 +61,7 @@
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
-			GPIO_ACTIVE_HIGH>;
+			GPIO_ACTIVE_LOW>;
 
 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
@@ -69,44 +69,38 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	regulators {
-		vcc_24v_reg: regulator@100 {
-			compatible = "regulator-fixed";
-			reg = <100>;
-			regulator-name = "vcc_24v";
-			regulator-min-microvolt = <24000000>;
-			regulator-max-microvolt = <24000000>;
-			regulator-always-on;
-		};
+	vcc_24v_reg: regulator-24v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_24v";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+		regulator-always-on;
+	};
 
-		vdd_5v0_reg: regulator@101 {
-			compatible = "regulator-fixed";
-			reg = <101>;
-			regulator-name = "vdd_5v0";
-			vin-supply = <&vcc_24v_reg>;
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		vin-supply = <&vcc_24v_reg>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		vdd_3v3_reg: regulator@102 {
-			compatible = "regulator-fixed";
-			reg = <102>;
-			regulator-name = "vdd_3v3";
-			vin-supply = <&vcc_24v_reg>;
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	vdd_3v3_reg: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		vin-supply = <&vcc_24v_reg>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		vdd_1v8_reg: regulator@103 {
-			compatible = "regulator-fixed";
-			reg = <103>;
-			regulator-name = "vdd_1v8";
-			vin-supply = <&vdd_3v3_reg>;
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
+	vdd_1v8_reg: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8";
+		vin-supply = <&vdd_3v3_reg>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra20-trimslice.dts b/arch/arm/boot/dts/nvidia/tegra20-trimslice.dts
index 8debd3d3c20d..7cae6ad57544 100644
--- a/arch/arm/boot/dts/tegra20-trimslice.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-trimslice.dts
@@ -276,6 +276,8 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -287,7 +289,8 @@
 	spi@7000c380 {
 		status = "okay";
 		spi-max-frequency = <48000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q80bl", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <48000000>;
@@ -321,6 +324,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	pcie@80003000 {
@@ -348,8 +352,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 0)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -366,36 +368,39 @@
 		status = "okay";
 	};
 
-	sdhci@c8000000 {
+	mmc@c8000000 {
 		status = "okay";
 		broken-cd;
 		bus-width = <4>;
 	};
 
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(P, 1) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
 		bus-width = <4>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
 
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+	cpus {
+		cpu0: cpu@0 {
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@1 {
+			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(X, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -408,58 +413,55 @@
 		gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	hdmi_vdd_reg: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd_hdmi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		hdmi_vdd_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "avdd_hdmi";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	hdmi_pll_reg: regulator-hdmipll {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd_hdmi_pll";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
 
-		hdmi_pll_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "avdd_hdmi_pll";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
+	vbus_reg: regulator-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(V, 2) 0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 
-		vbus_reg: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(V, 2) 0>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
+	pci_clk_reg: regulator-pciclk {
+		compatible = "regulator-fixed";
+		regulator-name = "pci_clk";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		pci_clk_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "pci_clk";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	pci_vdd_reg: regulator-pcivdd {
+		compatible = "regulator-fixed";
+		regulator-name = "pci_vdd";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-always-on;
+	};
 
-		pci_vdd_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "pci_vdd";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			regulator-always-on;
-		};
+	vdd_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_core";
+		regulator-min-microvolt = <1300000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-always-on;
 	};
 
 	sound {
@@ -472,14 +474,4 @@
 			 <&tegra_car TEGRA20_CLK_CDEV1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
-
-	cpus {
-		cpu0: cpu@0 {
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@1 {
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/nvidia/tegra20-ventana.dts
index f44551e2d9d0..f3273941437c 100644
--- a/arch/arm/boot/dts/tegra20-ventana.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-ventana.dts
@@ -2,7 +2,10 @@
 /dts-v1/;
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "tegra20.dtsi"
+#include "tegra20-cpu-opp.dtsi"
+#include "tegra20-cpu-opp-microvolt.dtsi"
 
 / {
 	model = "NVIDIA Tegra20 Ventana evaluation board";
@@ -281,7 +284,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -292,25 +295,25 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -320,6 +323,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -359,31 +364,6 @@
 		clock-frequency = <100000>;
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		lvds_ddc: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
 	i2c@7000c500 {
 		status = "okay";
 		clock-frequency = <400000>;
@@ -419,18 +399,28 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&rtc_vdd &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
 					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
 				};
 
-				sm1 {
+				vdd_cpu: sm1 {
 					regulator-name = "vdd_sm1,vdd_cpu";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-coupled-with = <&vdd_core &rtc_vdd>;
+					regulator-coupled-max-spread = <550000 550000>;
 					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				sm2_reg: sm2 {
@@ -449,10 +439,16 @@
 					regulator-always-on;
 				};
 
-				ldo2 {
+				rtc_vdd: ldo2 {
 					regulator-name = "vdd_ldo2,vdd_rtc";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&vdd_core &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-rtc-regulator;
 				};
 
 				ldo3 {
@@ -510,9 +506,10 @@
 			};
 		};
 
-		temperature-sensor@4c {
+		nct1008: temperature-sensor@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
+			#thermal-sensor-cells = <1>;
 		};
 	};
 
@@ -524,6 +521,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <458>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	usb@c5000000 {
@@ -536,8 +534,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -554,14 +550,14 @@
 		status = "okay";
 	};
 
-	sdhci@c8000000 {
+	mmc@c8000000 {
 		status = "okay";
 		power-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
 		bus-width = <4>;
 		keep-power-in-suspend;
 	};
 
-	sdhci@c8000400 {
+	mmc@c8000400 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
@@ -569,7 +565,7 @@
 		bus-width = <4>;
 	};
 
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -586,23 +582,30 @@
 		default-brightness-level = <6>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
 
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -610,8 +613,33 @@
 		};
 	};
 
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		lvds_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	panel: panel {
-		compatible = "chunghwa,claa101wa01a", "simple-panel";
+		compatible = "chunghwa,claa101wa01a";
 
 		power-supply = <&vdd_pnl_reg>;
 		enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
@@ -620,58 +648,47 @@
 		ddc-i2c-bus = <&lvds_ddc>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_5v0_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd_5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vdd_1v5";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v5";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+	};
 
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vdd_1v2";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_pnl_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vdd_pnl";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_pnl_reg: regulator-pnl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_pnl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		vdd_bl_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "vdd_bl";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	vdd_bl_reg: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
@@ -693,7 +710,7 @@
 		nvidia,audio-codec = <&wm8903>;
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
 		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(X, 0)
 			GPIO_ACTIVE_HIGH>;
 		nvidia,ext-mic-en-gpios = <&gpio TEGRA_GPIO(X, 1)
@@ -704,4 +721,37 @@
 			 <&tegra_car TEGRA20_CLK_CDEV1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip0: cpu-alert0 {
+					/* start throttling at 50C */
+					temperature = <50000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: cpu-crit {
+					/* shut down at 60C */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/nvidia/tegra20.dtsi
index 9c58e7fcf5c0..8da75ccc4402 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20.dtsi
@@ -4,6 +4,9 @@
 #include <dt-bindings/memory/tegra20-mc.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/tegra-pmc.h>
+
+#include "tegra20-peripherals-opp.dtsi"
 
 / {
 	compatible = "nvidia,tegra20";
@@ -16,27 +19,31 @@
 		reg = <0 0>;
 	};
 
-	iram@40000000 {
+	sram@40000000 {
 		compatible = "mmio-sram";
 		reg = <0x40000000 0x40000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x40000000 0x40000>;
 
-		vde_pool: vde@400 {
+		vde_pool: sram@400 {
 			reg = <0x400 0x3fc00>;
 			pool;
 		};
 	};
 
 	host1x@50000000 {
-		compatible = "nvidia,tegra20-host1x", "simple-bus";
+		compatible = "nvidia,tegra20-host1x";
 		reg = <0x50000000 0x00024000>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */
 			     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */
+		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		clock-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA20_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&host1x_dvfs_opp_table>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -50,6 +57,9 @@
 			clocks = <&tegra_car TEGRA20_CLK_MPE>;
 			resets = <&tegra_car 60>;
 			reset-names = "mpe";
+			power-domains = <&pd_mpe>;
+			operating-points-v2 = <&mpe_dvfs_opp_table>;
+			status = "disabled";
 		};
 
 		vi@54080000 {
@@ -59,6 +69,9 @@
 			clocks = <&tegra_car TEGRA20_CLK_VI>;
 			resets = <&tegra_car 20>;
 			reset-names = "vi";
+			power-domains = <&pd_venc>;
+			operating-points-v2 = <&vi_dvfs_opp_table>;
+			status = "disabled";
 		};
 
 		epp@540c0000 {
@@ -68,6 +81,9 @@
 			clocks = <&tegra_car TEGRA20_CLK_EPP>;
 			resets = <&tegra_car 19>;
 			reset-names = "epp";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&epp_dvfs_opp_table>;
+			status = "disabled";
 		};
 
 		isp@54100000 {
@@ -77,6 +93,8 @@
 			clocks = <&tegra_car TEGRA20_CLK_ISP>;
 			resets = <&tegra_car 23>;
 			reset-names = "isp";
+			power-domains = <&pd_venc>;
+			status = "disabled";
 		};
 
 		gr2d@54140000 {
@@ -84,16 +102,20 @@
 			reg = <0x54140000 0x00040000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA20_CLK_GR2D>;
-			resets = <&tegra_car 21>;
-			reset-names = "2d";
+			resets = <&tegra_car 21>, <&mc TEGRA20_MC_RESET_2D>;
+			reset-names = "2d", "mc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&gr2d_dvfs_opp_table>;
 		};
 
 		gr3d@54180000 {
 			compatible = "nvidia,tegra20-gr3d";
 			reg = <0x54180000 0x00040000>;
 			clocks = <&tegra_car TEGRA20_CLK_GR3D>;
-			resets = <&tegra_car 24>;
-			reset-names = "3d";
+			resets = <&tegra_car 24>, <&mc TEGRA20_MC_RESET_3D>;
+			reset-names = "3d", "mc";
+			power-domains = <&pd_3d>;
+			operating-points-v2 = <&gr3d_dvfs_opp_table>;
 		};
 
 		dc@54200000 {
@@ -105,9 +127,22 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 27>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp1_dvfs_opp_table>;
 
 			nvidia,head = <0>;
 
+			interconnects = <&mc TEGRA20_MC_DISPLAY0A &emc>,
+					<&mc TEGRA20_MC_DISPLAY0B &emc>,
+					<&mc TEGRA20_MC_DISPLAY1B &emc>,
+					<&mc TEGRA20_MC_DISPLAY0C &emc>,
+					<&mc TEGRA20_MC_DISPLAYHC &emc>;
+			interconnect-names = "wina",
+					     "winb",
+					     "winb-vfilter",
+					     "winc",
+					     "cursor";
+
 			rgb {
 				status = "disabled";
 			};
@@ -122,15 +157,28 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 26>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp2_dvfs_opp_table>;
 
 			nvidia,head = <1>;
 
+			interconnects = <&mc TEGRA20_MC_DISPLAY0AB &emc>,
+					<&mc TEGRA20_MC_DISPLAY0BB &emc>,
+					<&mc TEGRA20_MC_DISPLAY1BB &emc>,
+					<&mc TEGRA20_MC_DISPLAY0CB &emc>,
+					<&mc TEGRA20_MC_DISPLAYHCB &emc>;
+			interconnect-names = "wina",
+					     "winb",
+					     "winb-vfilter",
+					     "winc",
+					     "cursor";
+
 			rgb {
 				status = "disabled";
 			};
 		};
 
-		hdmi@54280000 {
+		tegra_hdmi: hdmi@54280000 {
 			compatible = "nvidia,tegra20-hdmi";
 			reg = <0x54280000 0x00040000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -139,6 +187,9 @@
 			clock-names = "hdmi", "parent";
 			resets = <&tegra_car 51>;
 			reset-names = "hdmi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&hdmi_dvfs_opp_table>;
+			#sound-dai-cells = <0>;
 			status = "disabled";
 		};
 
@@ -147,15 +198,21 @@
 			reg = <0x542c0000 0x00040000>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA20_CLK_TVO>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&tvo_dvfs_opp_table>;
 			status = "disabled";
 		};
 
 		dsi@54300000 {
 			compatible = "nvidia,tegra20-dsi";
 			reg = <0x54300000 0x00040000>;
-			clocks = <&tegra_car TEGRA20_CLK_DSI>;
+			clocks = <&tegra_car TEGRA20_CLK_DSI>,
+				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "parent";
 			resets = <&tegra_car 48>;
 			reset-names = "dsi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&dsi_dvfs_opp_table>;
 			status = "disabled";
 		};
 	};
@@ -171,8 +228,8 @@
 
 	intc: interrupt-controller@50041000 {
 		compatible = "arm,cortex-a9-gic";
-		reg = <0x50041000 0x1000
-		       0x50040100 0x0100>;
+		reg = <0x50041000 0x1000>,
+		      <0x50040100 0x0100>;
 		interrupt-controller;
 		#interrupt-cells = <3>;
 		interrupt-parent = <&intc>;
@@ -213,6 +270,13 @@
 		reg = <0x60006000 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
+
+		sclk {
+			compatible = "nvidia,tegra20-sclk";
+			clocks = <&tegra_car TEGRA20_CLK_SCLK>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&sclk_dvfs_opp_table>;
+		};
 	};
 
 	flow-controller@60007000 {
@@ -264,22 +328,20 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 224>;
-		*/
 	};
 
 	vde@6001a000 {
 		compatible = "nvidia,tegra20-vde";
-		reg = <0x6001a000 0x1000   /* Syntax Engine */
-		       0x6001b000 0x1000   /* Video Bitstream Engine */
-		       0x6001c000  0x100   /* Macroblock Engine */
-		       0x6001c200  0x100   /* Post-processing Engine */
-		       0x6001c400  0x100   /* Motion Compensation Engine */
-		       0x6001c600  0x100   /* Transform Engine */
-		       0x6001c800  0x100   /* Pixel prediction block */
-		       0x6001ca00  0x100   /* Video DMA */
-		       0x6001d800  0x300>; /* Video frame controls */
+		reg = <0x6001a000 0x1000>, /* Syntax Engine */
+		      <0x6001b000 0x1000>, /* Video Bitstream Engine */
+		      <0x6001c000  0x100>, /* Macroblock Engine */
+		      <0x6001c200  0x100>, /* Post-processing Engine */
+		      <0x6001c400  0x100>, /* Motion Compensation Engine */
+		      <0x6001c600  0x100>, /* Transform Engine */
+		      <0x6001c800  0x100>, /* Pixel prediction block */
+		      <0x6001ca00  0x100>, /* Video DMA */
+		      <0x6001d800  0x300>; /* Video frame controls */
 		reg-names = "sxe", "bsev", "mbe", "ppe", "mce",
 			    "tfe", "ppb", "vdma", "frameid";
 		iram = <&vde_pool>; /* IRAM region */
@@ -290,20 +352,22 @@
 		clocks = <&tegra_car TEGRA20_CLK_VDE>;
 		reset-names = "vde", "mc";
 		resets = <&tegra_car 61>, <&mc TEGRA20_MC_RESET_VDE>;
-	};
-
-	apbmisc@70000800 {
-		compatible = "nvidia,tegra20-apbmisc";
-		reg = <0x70000800 0x64   /* Chip revision */
-		       0x70000008 0x04>; /* Strapping options */
+		power-domains = <&pd_vde>;
+		operating-points-v2 = <&vde_dvfs_opp_table>;
 	};
 
 	pinmux: pinmux@70000014 {
 		compatible = "nvidia,tegra20-pinmux";
-		reg = <0x70000014 0x10   /* Tri-state registers */
-		       0x70000080 0x20   /* Mux registers */
-		       0x700000a0 0x14   /* Pull-up/down registers */
-		       0x70000868 0xa8>; /* Pad control registers */
+		reg = <0x70000014 0x10>, /* Tri-state registers */
+		      <0x70000080 0x20>, /* Mux registers */
+		      <0x700000a0 0x14>, /* Pull-up/down registers */
+		      <0x70000868 0xa8>; /* Pad control registers */
+	};
+
+	apbmisc@70000800 {
+		compatible = "nvidia,tegra20-apbmisc";
+		reg = <0x70000800 0x64>, /* Chip revision */
+		      <0x70000008 0x04>; /* Strapping options */
 	};
 
 	das@70000c00 {
@@ -323,6 +387,23 @@
 		status = "disabled";
 	};
 
+	tegra_spdif: spdif@70002400 {
+		compatible = "nvidia,tegra20-spdif";
+		reg = <0x70002400 0x200>;
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA20_CLK_SPDIF_OUT>,
+			 <&tegra_car TEGRA20_CLK_SPDIF_IN>;
+		clock-names = "out", "in";
+		resets = <&tegra_car 10>;
+		dmas = <&apbdma 3>, <&apbdma 3>;
+		dma-names = "rx", "tx";
+		#sound-dai-cells = <0>;
+		status = "disabled";
+
+		assigned-clocks = <&tegra_car TEGRA20_CLK_SPDIF_OUT>;
+		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_A_OUT0>;
+	};
+
 	tegra_i2s1: i2s@70002800 {
 		compatible = "nvidia,tegra20-i2s";
 		reg = <0x70002800 0x200>;
@@ -361,7 +442,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -374,7 +454,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -387,7 +466,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -400,7 +478,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -413,7 +490,6 @@
 		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTE>;
 		resets = <&tegra_car 66>;
-		reset-names = "serial";
 		dmas = <&apbdma 20>, <&apbdma 20>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -431,6 +507,8 @@
 		reset-names = "nand";
 		assigned-clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
 		assigned-clock-rates = <150000000>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&ndflash_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -444,6 +522,8 @@
 		clock-names = "gmi";
 		resets = <&tegra_car 42>;
 		reset-names = "gmi";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&nor_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -457,13 +537,6 @@
 		status = "disabled";
 	};
 
-	rtc@7000e000 {
-		compatible = "nvidia,tegra20-rtc";
-		reg = <0x7000e000 0x100>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA20_CLK_RTC>;
-	};
-
 	i2c@7000c000 {
 		compatible = "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
@@ -494,7 +567,7 @@
 		status = "disabled";
 	};
 
-	i2c@7000c400 {
+	i2c2: i2c@7000c400 {
 		compatible = "nvidia,tegra20-i2c";
 		reg = <0x7000c400 0x100>;
 		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
@@ -598,6 +671,13 @@
 		status = "disabled";
 	};
 
+	rtc@7000e000 {
+		compatible = "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA20_CLK_RTC>;
+	};
+
 	kbc@7000e200 {
 		compatible = "nvidia,tegra20-kbc";
 		reg = <0x7000e200 0x100>;
@@ -608,31 +688,84 @@
 		status = "disabled";
 	};
 
-	pmc@7000e400 {
+	tegra_pmc: pmc@7000e400 {
 		compatible = "nvidia,tegra20-pmc";
 		reg = <0x7000e400 0x400>;
 		clocks = <&tegra_car TEGRA20_CLK_PCLK>, <&clk32k_in>;
 		clock-names = "pclk", "clk32k_in";
+		#clock-cells = <1>;
+
+		pd_core: core-domain {
+			#power-domain-cells = <0>;
+			operating-points-v2 = <&core_opp_table>;
+		};
+
+		powergates {
+			pd_mpe: mpe {
+				clocks = <&tegra_car TEGRA20_CLK_MPE>;
+				resets = <&mc TEGRA20_MC_RESET_MPEA>,
+					 <&mc TEGRA20_MC_RESET_MPEB>,
+					 <&mc TEGRA20_MC_RESET_MPEC>,
+					 <&tegra_car TEGRA20_CLK_MPE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_3d: td {
+				clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+				resets = <&mc TEGRA20_MC_RESET_3D>,
+					 <&tegra_car TEGRA20_CLK_GR3D>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_vde: vdec {
+				clocks = <&tegra_car TEGRA20_CLK_VDE>;
+				resets = <&mc TEGRA20_MC_RESET_VDE>,
+					 <&tegra_car TEGRA20_CLK_VDE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_venc: venc {
+				clocks = <&tegra_car TEGRA20_CLK_ISP>,
+					 <&tegra_car TEGRA20_CLK_VI>,
+					 <&tegra_car TEGRA20_CLK_CSI>;
+				resets = <&mc TEGRA20_MC_RESET_ISP>,
+					 <&mc TEGRA20_MC_RESET_VI>,
+					 <&tegra_car TEGRA20_CLK_ISP>,
+					 <&tegra_car 20 /* VI */>,
+					 <&tegra_car TEGRA20_CLK_CSI>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+		};
 	};
 
 	mc: memory-controller@7000f000 {
 		compatible = "nvidia,tegra20-mc-gart";
-		reg = <0x7000f000 0x400		/* controller registers */
-		       0x58000000 0x02000000>;	/* GART aperture */
+		reg = <0x7000f000 0x00000400>, /* controller registers */
+		      <0x58000000 0x02000000>; /* GART aperture */
 		clocks = <&tegra_car TEGRA20_CLK_MC>;
 		clock-names = "mc";
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 		#reset-cells = <1>;
 		#iommu-cells = <0>;
+		#interconnect-cells = <1>;
 	};
 
-	memory-controller@7000f400 {
+	emc: memory-controller@7000f400 {
 		compatible = "nvidia,tegra20-emc";
-		reg = <0x7000f400 0x200>;
+		reg = <0x7000f400 0x400>;
 		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_EMC>;
+		power-domains = <&pd_core>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		#interconnect-cells = <0>;
+
+		nvidia,memory-controller = <&mc>;
+		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
 	};
 
 	fuse@7000f800 {
@@ -647,12 +780,12 @@
 	pcie@80003000 {
 		compatible = "nvidia,tegra20-pcie";
 		device_type = "pci";
-		reg = <0x80003000 0x00000800   /* PADS registers */
-		       0x80003800 0x00000200   /* AFI registers */
-		       0x90000000 0x10000000>; /* configuration space */
+		reg = <0x80003000 0x00000800>, /* PADS registers */
+		      <0x80003800 0x00000200>, /* AFI registers */
+		      <0x90000000 0x10000000>; /* configuration space */
 		reg-names = "pads", "afi", "cs";
-		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH   /* controller interrupt */
-			      GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
 		interrupt-names = "intr", "msi";
 
 		#interrupt-cells = <1>;
@@ -663,11 +796,11 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 
-		ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000   /* port 0 registers */
-			  0x82000000 0 0x80001000 0x80001000 0 0x00001000   /* port 1 registers */
-			  0x81000000 0 0          0x82000000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0xa0000000 0xa0000000 0 0x08000000   /* non-prefetchable memory */
-			  0xc2000000 0 0xa8000000 0xa8000000 0 0x18000000>; /* prefetchable memory */
+		ranges = <0x02000000 0 0x80000000 0x80000000 0 0x00001000>, /* port 0 registers */
+			 <0x02000000 0 0x80001000 0x80001000 0 0x00001000>, /* port 1 registers */
+			 <0x01000000 0 0          0x82000000 0 0x00010000>, /* downstream I/O */
+			 <0x02000000 0 0xa0000000 0xa0000000 0 0x08000000>, /* non-prefetchable memory */
+			 <0x42000000 0 0xa8000000 0xa8000000 0 0x18000000>; /* prefetchable memory */
 
 		clocks = <&tegra_car TEGRA20_CLK_PEX>,
 			 <&tegra_car TEGRA20_CLK_AFI>,
@@ -677,6 +810,9 @@
 			 <&tegra_car 72>,
 			 <&tegra_car 74>;
 		reset-names = "pex", "afi", "pcie_x";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&pcie_dvfs_opp_table>;
+
 		status = "disabled";
 
 		pci@1,0 {
@@ -709,22 +845,25 @@
 	};
 
 	usb@c5000000 {
-		compatible = "nvidia,tegra20-ehci", "usb-ehci";
+		compatible = "nvidia,tegra20-ehci";
 		reg = <0xc5000000 0x4000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
-		nvidia,has-legacy-mode;
 		clocks = <&tegra_car TEGRA20_CLK_USBD>;
 		resets = <&tegra_car 22>;
 		reset-names = "usb";
 		nvidia,needs-double-reset;
 		nvidia,phy = <&phy1>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usbd_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	phy1: usb-phy@c5000000 {
 		compatible = "nvidia,tegra20-usb-phy";
-		reg = <0xc5000000 0x4000 0xc5000000 0x4000>;
+		reg = <0xc5000000 0x4000>,
+		      <0xc5000000 0x4000>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA20_CLK_USBD>,
 			 <&tegra_car TEGRA20_CLK_PLL_U>,
@@ -733,6 +872,7 @@
 		clock-names = "reg", "pll_u", "timer", "utmi-pads";
 		resets = <&tegra_car 22>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,has-legacy-mode;
 		nvidia,hssync-start-delay = <9>;
 		nvidia,idle-wait-delay = <17>;
@@ -742,11 +882,12 @@
 		nvidia,xcvr-lsfslew = <1>;
 		nvidia,xcvr-lsrslew = <1>;
 		nvidia,has-utmi-pad-registers;
+		nvidia,pmc = <&tegra_pmc 0>;
 		status = "disabled";
 	};
 
 	usb@c5004000 {
-		compatible = "nvidia,tegra20-ehci", "usb-ehci";
+		compatible = "nvidia,tegra20-ehci";
 		reg = <0xc5004000 0x4000>;
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "ulpi";
@@ -754,12 +895,15 @@
 		resets = <&tegra_car 58>;
 		reset-names = "usb";
 		nvidia,phy = <&phy2>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	phy2: usb-phy@c5004000 {
 		compatible = "nvidia,tegra20-usb-phy";
 		reg = <0xc5004000 0x4000>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "ulpi";
 		clocks = <&tegra_car TEGRA20_CLK_USB2>,
 			 <&tegra_car TEGRA20_CLK_PLL_U>,
@@ -767,11 +911,13 @@
 		clock-names = "reg", "pll_u", "ulpi-link";
 		resets = <&tegra_car 58>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
+		nvidia,pmc = <&tegra_pmc 1>;
 		status = "disabled";
 	};
 
 	usb@c5008000 {
-		compatible = "nvidia,tegra20-ehci", "usb-ehci";
+		compatible = "nvidia,tegra20-ehci";
 		reg = <0xc5008000 0x4000>;
 		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -779,12 +925,16 @@
 		resets = <&tegra_car 59>;
 		reset-names = "usb";
 		nvidia,phy = <&phy3>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	phy3: usb-phy@c5008000 {
 		compatible = "nvidia,tegra20-usb-phy";
-		reg = <0xc5008000 0x4000 0xc5000000 0x4000>;
+		reg = <0xc5008000 0x4000>,
+		      <0xc5000000 0x4000>;
+		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA20_CLK_USB3>,
 			 <&tegra_car TEGRA20_CLK_PLL_U>,
@@ -793,6 +943,7 @@
 		clock-names = "reg", "pll_u", "timer", "utmi-pads";
 		resets = <&tegra_car 59>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <9>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -800,46 +951,59 @@
 		nvidia,xcvr-setup = <9>;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
+		nvidia,pmc = <&tegra_pmc 2>;
 		status = "disabled";
 	};
 
-	sdhci@c8000000 {
+	mmc@c8000000 {
 		compatible = "nvidia,tegra20-sdhci";
 		reg = <0xc8000000 0x200>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_SDMMC1>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 14>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc1_dvfs_opp_table>;
 		status = "disabled";
 	};
 
-	sdhci@c8000200 {
+	mmc@c8000200 {
 		compatible = "nvidia,tegra20-sdhci";
 		reg = <0xc8000200 0x200>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_SDMMC2>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 9>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
-	sdhci@c8000400 {
+	mmc@c8000400 {
 		compatible = "nvidia,tegra20-sdhci";
 		reg = <0xc8000400 0x200>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_SDMMC3>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 69>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
-	sdhci@c8000600 {
+	mmc@c8000600 {
 		compatible = "nvidia,tegra20-sdhci";
 		reg = <0xc8000600 0x200>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_SDMMC4>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 15>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc4_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -869,4 +1033,24 @@
 		interrupt-affinity = <&{/cpus/cpu@0}>,
 				     <&{/cpus/cpu@1}>;
 	};
+
+	sound-hdmi {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "NVIDIA Tegra20 HDMI";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+
+			codec {
+				sound-dai = <&tegra_hdmi>;
+			};
+
+			cpu {
+				sound-dai = <&tegra_spdif>;
+			};
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/nvidia/tegra30-apalis-eval.dts
index 749fc6d1ff70..fc284155cd76 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-eval.dts
@@ -47,8 +47,20 @@
 		};
 	};
 
+	gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -120,7 +132,7 @@
 	};
 
 	/* Apalis SD1 */
-	sdhci@78000000 {
+	mmc@78000000 {
 		status = "okay";
 		bus-width = <4>;
 		/* SD1_CD# */
@@ -129,7 +141,7 @@
 	};
 
 	/* Apalis MMC1 */
-	sdhci@78000400 {
+	mmc@78000400 {
 		status = "okay";
 		bus-width = <8>;
 		/* MMC1_CD# */
@@ -181,7 +193,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -195,7 +207,7 @@
 		 * edt,et057090dhu: EDT 5.7" LCD TFT
 		 * edt,et070080dh6: EDT 7.0" LCD TFT
 		 */
-		compatible = "edt,et057090dhu", "simple-panel";
+		compatible = "edt,et057090dhu";
 		backlight = <&backlight>;
 		power-supply = <&reg_3v3>;
 	};
@@ -236,13 +248,3 @@
 		vin-supply = <&reg_5v0>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1-eval.dts
index 0be50e881684..9d08e2b094b4 100644
--- a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1-eval.dts
@@ -48,8 +48,20 @@
 		};
 	};
 
+	gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -121,7 +133,7 @@
 	};
 
 	/* Apalis SD1 */
-	sdhci@78000000 {
+	mmc@78000000 {
 		status = "okay";
 		bus-width = <4>;
 		/* SD1_CD# */
@@ -130,7 +142,7 @@
 	};
 
 	/* Apalis MMC1 */
-	sdhci@78000400 {
+	mmc@78000400 {
 		status = "okay";
 		bus-width = <8>;
 		/* MMC1_CD# */
@@ -182,7 +194,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -196,7 +208,7 @@
 		 * edt,et057090dhu: EDT 5.7" LCD TFT
 		 * edt,et070080dh6: EDT 7.0" LCD TFT
 		 */
-		compatible = "edt,et057090dhu", "simple-panel";
+		compatible = "edt,et057090dhu";
 		backlight = <&backlight>;
 		power-supply = <&reg_3v3>;
 	};
@@ -248,19 +260,9 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-type = "voltage";
 		gpios = <&gpio TEGRA_GPIO(J, 5) GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x0
-			  3300000 0x1>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
 		startup-delay-us = <100000>;
 		vin-supply = <&vddio_sdmmc_1v8_reg>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1.dtsi
index 8b7a827d604d..1640763fd4af 100644
--- a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1.dtsi
@@ -37,7 +37,7 @@
 			status = "okay";
 			nvidia,num-lanes = <1>;
 
-			pcie@0 {
+			ethernet@0,0 {
 				reg = <0 0 0 0 0>;
 				local-mac-address = [00 00 00 00 00 00];
 			};
@@ -829,14 +829,20 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -855,6 +861,7 @@
 		sgtl5000: codec@a {
 			compatible = "fsl,sgtl5000";
 			reg = <0x0a>;
+			#sound-dai-cells = <0>;
 			VDDA-supply = <&reg_module_3v3_audio>;
 			VDDD-supply = <&reg_1v8_vio>;
 			VDDIO-supply = <&reg_module_3v3>;
@@ -989,7 +996,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			interrupt-controller;
 			id = <0>;
 			blocks = <0x5>;
@@ -1003,6 +1010,12 @@
 			/* ADC converstion time: 80 clocks */
 			st,sample-time = <4>;
 
+			stmpe_adc {
+				compatible = "st,stmpe-adc";
+				/* forbid to use ADC channels 3-0 (touch) */
+				st,norequest-mask = <0x0F>;
+			};
+
 			stmpe_touchscreen {
 				compatible = "st,stmpe-ts";
 				/* 8 sample average control */
@@ -1019,12 +1032,6 @@
 				/* 5 ms touch detect interrupt delay */
 				st,touch-det-delay = <5>;
 			};
-
-			stmpe_adc {
-				compatible = "st,stmpe-adc";
-				/* forbid to use ADC channels 3-0 (touch) */
-				st,norequest-mask = <0x0F>;
-			};
 		};
 
 		/*
@@ -1046,9 +1053,6 @@
 			regulator-max-microvolt = <1400000>;
 			regulator-boot-on;
 			regulator-always-on;
-			ti,vsel0-state-low;
-			/* VSEL1: EN_CORE_DVFS_N low for DVFS */
-			ti,vsel1-state-low;
 		};
 	};
 
@@ -1112,7 +1116,7 @@
 	};
 
 	/* eMMC */
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1121,16 +1125,16 @@
 		mmc-ddr-1_8v;
 	};
 
-	clk32k_in: xtal1 {
+	clk16m: clock-osc4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
+		clock-frequency = <16000000>;
 	};
 
-	clk16m: osc4 {
+	clk32k_in: clock-xtal1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <16000000>;
+		clock-frequency = <32768>;
 	};
 
 	reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
@@ -1189,7 +1193,13 @@
 		nvidia,audio-codec = <&sgtl5000>;
 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA30_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 };
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/nvidia/tegra30-apalis.dtsi
index c18f6f61d764..3b6fad273cab 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis.dtsi
@@ -36,7 +36,7 @@
 			status = "okay";
 			nvidia,num-lanes = <1>;
 
-			pcie@0 {
+			ethernet@0,0 {
 				reg = <0 0 0 0 0>;
 				local-mac-address = [00 00 00 00 00 00];
 			};
@@ -820,14 +820,20 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -846,6 +852,7 @@
 		sgtl5000: codec@a {
 			compatible = "fsl,sgtl5000";
 			reg = <0x0a>;
+			#sound-dai-cells = <0>;
 			VDDA-supply = <&reg_module_3v3_audio>;
 			VDDD-supply = <&reg_1v8_vio>;
 			VDDIO-supply = <&reg_module_3v3>;
@@ -859,6 +866,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
+			wakeup-source;
 
 			ti,system-power-controller;
 
@@ -971,7 +979,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			interrupt-controller;
 			id = <0>;
 			blocks = <0x5>;
@@ -985,6 +993,12 @@
 			/* ADC converstion time: 80 clocks */
 			st,sample-time = <4>;
 
+			stmpe_adc {
+				compatible = "st,stmpe-adc";
+				/* forbid to use ADC channels 3-0 (touch) */
+				st,norequest-mask = <0x0F>;
+			};
+
 			stmpe_touchscreen {
 				compatible = "st,stmpe-ts";
 				/* 8 sample average control */
@@ -1001,12 +1015,6 @@
 				/* 5 ms touch detect interrupt delay */
 				st,touch-det-delay = <5>;
 			};
-
-			stmpe_adc {
-				compatible = "st,stmpe-adc";
-				/* forbid to use ADC channels 3-0 (touch) */
-				st,norequest-mask = <0x0F>;
-			};
 		};
 
 		/*
@@ -1028,9 +1036,6 @@
 			regulator-max-microvolt = <1400000>;
 			regulator-boot-on;
 			regulator-always-on;
-			ti,vsel0-state-low;
-			/* VSEL1: EN_CORE_DVFS_N low for DVFS */
-			ti,vsel1-state-low;
 		};
 	};
 
@@ -1094,7 +1099,7 @@
 	};
 
 	/* eMMC */
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1103,16 +1108,16 @@
 		mmc-ddr-1_8v;
 	};
 
-	clk32k_in: xtal1 {
+	clk16m: clock-osc4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
+		clock-frequency = <16000000>;
 	};
 
-	clk16m: osc4 {
+	clk32k_in: clock-xtal1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <16000000>;
+		clock-frequency = <32768>;
 	};
 
 	reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
@@ -1171,7 +1176,13 @@
 		nvidia,audio-codec = <&sgtl5000>;
 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA30_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-lvds-display.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-lvds-display.dtsi
new file mode 100644
index 000000000000..680edff0f26f
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-lvds-display.dtsi
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This dtsi file describes parts common for Asus T30 devices with a LVDS panel. */
+
+#include <dt-bindings/gpio/tegra-gpio.h>
+
+/ {
+	host1x@50000000 {
+		lcd: dc@54200000 {
+			rgb {
+				status = "okay";
+
+				port {
+					dpi_output: endpoint {
+						remote-endpoint = <&bridge_input>;
+						bus-width = <24>;
+					};
+				};
+			};
+		};
+	};
+
+	display-panel {
+		power-supply = <&vdd_pnl>;
+		ddc-i2c-bus = <&lcd_ddc>;
+		backlight = <&backlight>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&bridge_output>;
+			};
+		};
+	};
+
+	/* Texas Instruments SN75LVDS83B LVDS Transmitter */
+	lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+
+		powerdown-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_3v3_sys>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				bridge_input: endpoint {
+					remote-endpoint = <&dpi_output>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				bridge_output: endpoint {
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-E1565.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-E1565.dts
new file mode 100644
index 000000000000..a25b8560b0cd
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-E1565.dts
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-nexus7-grouper-maxim-pmic.dtsi"
+#include "tegra30-asus-nexus7-grouper.dtsi"
+
+/ {
+	model = "ASUS Google Nexus 7 (Project Nakasi / ME370T) E1565";
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-PM269.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-PM269.dts
new file mode 100644
index 000000000000..06ef13ea5df8
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-PM269.dts
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-nexus7-grouper-ti-pmic.dtsi"
+#include "tegra30-asus-nexus7-grouper.dtsi"
+
+/ {
+	model = "ASUS Google Nexus 7 (Project Nakasi / ME370T) PM269";
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-common.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-common.dtsi
new file mode 100644
index 000000000000..a9342e04b14b
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-common.dtsi
@@ -0,0 +1,1318 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/power/summit,smb347-charger.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc3; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <0x0>;
+			tlm,version-minor = <0x0>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@bfdf0000 {
+			compatible = "ramoops";
+			reg = <0xbfdf0000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;
+			no-map;
+		};
+	};
+
+	gpio@6000d000 {
+		init-low-power-mode-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+			input;
+		};
+
+		init-mode-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(CC, 6) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			clk_32k_out_pa0 {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			uart3_cts_n_pa1 {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap2_fs_pa2 {
+				nvidia,pins = "dap2_fs_pa2",
+						"dap2_sclk_pa3",
+						"dap2_din_pa4",
+						"dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat3_pb4",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat4_pd1",
+						"sdmmc3_dat6_pd3",
+						"sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+						"gmi_a18_pb1";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+						"lcd_pwr1_pc1",
+						"lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			lcd_pclk_pb3 {
+				nvidia,pins = "lcd_pclk_pb3",
+						"lcd_d0_pe0",
+						"lcd_d1_pe1",
+						"lcd_d2_pe2",
+						"lcd_d3_pe3",
+						"lcd_d4_pe4",
+						"lcd_d5_pe5",
+						"lcd_d6_pe6",
+						"lcd_d7_pe7",
+						"lcd_d8_pf0",
+						"lcd_d9_pf1",
+						"lcd_d10_pf2",
+						"lcd_d11_pf3",
+						"lcd_d12_pf4",
+						"lcd_d13_pf5",
+						"lcd_d14_pf6",
+						"lcd_d15_pf7",
+						"lcd_de_pj1",
+						"lcd_hsync_pj3",
+						"lcd_vsync_pj4",
+						"lcd_d16_pm0",
+						"lcd_d17_pm1",
+						"lcd_d18_pm2",
+						"lcd_d19_pm3",
+						"lcd_d20_pm4",
+						"lcd_d21_pm5",
+						"lcd_d22_pm6",
+						"lcd_d23_pm7",
+						"lcd_cs0_n_pn4",
+						"lcd_sdout_pn5",
+						"lcd_dc0_pn6",
+						"lcd_cs1_n_pw0",
+						"lcd_sdin_pz2",
+						"lcd_sck_pz4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			uart3_rts_n_pc0 {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			uart2_txd_pc2 {
+				nvidia,pins = "uart2_txd_pc2",
+						"uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			uart2_rxd_pc3 {
+				nvidia,pins = "uart2_rxd_pc3",
+						"uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gen1_i2c_scl_pc4 {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7",
+						"gmi_wait_pi7",
+						"gmi_cs4_n_pk2",
+						"gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad12_ph4 {
+				nvidia,pins = "gmi_ad12_ph4",
+						"gmi_cs0_n_pj0",
+						"gmi_cs1_n_pj2",
+						"gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc3_dat5_pd0 {
+				nvidia,pins = "sdmmc3_dat5_pd0";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+						"gmi_ad1_pg1",
+						"gmi_ad14_ph6",
+						"pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad2_pg2 {
+				nvidia,pins = "gmi_ad2_pg2",
+						"gmi_ad3_pg3",
+						"gmi_ad6_pg6",
+						"gmi_ad7_pg7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad4_pg4 {
+				nvidia,pins = "gmi_ad4_pg4",
+						"gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_ad8_ph0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad11_ph3 {
+				nvidia,pins = "gmi_ad11_ph3";
+				nvidia,function = "pwm3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5",
+						"gmi_wr_n_pi0",
+						"gmi_oe_n_pi1",
+						"gmi_adv_n_pk0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_ad15_ph7 {
+				nvidia,pins = "gmi_ad15_ph7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_dqs_pi2 {
+				nvidia,pins = "gmi_dqs_pi2",
+						"pu2",
+						"pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_rst_n_pi4 {
+				nvidia,pins = "gmi_rst_n_pi4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_iordy_pi5 {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_cs7_n_pi6 {
+				nvidia,pins = "gmi_cs7_n_pi6",
+						"gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_a16_pj7 {
+				nvidia,pins = "gmi_a16_pj7",
+						"gmi_a19_pk7";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spdif_out_pk5 {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spdif_in_pk6 {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_din_pn1",
+						"dap1_dout_pn2",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			hdmi_int_pn7 {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			ulpi_data3_po4 {
+				nvidia,pins = "ulpi_data3_po4";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3_fs_pp0 {
+				nvidia,pins = "dap3_fs_pp0";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			dap4_fs_pp4 {
+				nvidia,pins = "dap4_fs_pp4",
+						"dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_col0_pq0 {
+				nvidia,pins = "kb_col0_pq0",
+						"kb_col1_pq1",
+						"kb_row1_pr1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_col2_pq2 {
+				nvidia,pins = "kb_col2_pq2",
+						"kb_col3_pq3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_col4_pq4 {
+				nvidia,pins = "kb_col4_pq4",
+						"kb_col5_pq5",
+						"kb_col7_pq7",
+						"kb_row2_pr2",
+						"kb_row4_pr4",
+						"kb_row5_pr5",
+						"kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_row6_pr6 {
+				nvidia,pins = "kb_row6_pr6",
+						"kb_row8_ps0",
+						"kb_row9_ps1",
+						"kb_row10_ps2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_row11_ps3 {
+				nvidia,pins = "kb_row11_ps3",
+						"kb_row12_ps4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gen2_i2c_scl_pt5 {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4_cmd_pt7 {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pu0 {
+				nvidia,pins = "pu0",
+						"pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			jtag_rtck_pu7 {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pv0 {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ddc_scl_pv4 {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6",
+						"crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spi2_cs1_n_pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2",
+						"spi2_miso_px1",
+						"spi2_sck_px2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk1_out_pw4 {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk2_out_pw5 {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi2_cs0_n_px3 {
+				nvidia,pins = "spi2_cs0_n_px3";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4",
+						"spi1_cs0_n_px6";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0",
+						"ulpi_dir_py1";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			sdmmc1_dat3_py4 {
+				nvidia,pins = "sdmmc1_dat3_py4",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat0_py7",
+						"sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1_clk_pz0 {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd_wr_n_pz3 {
+				nvidia,pins = "lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sys_clk_req_pz5 {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pwr_i2c_scl_pz6 {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+			pbb0 {
+				nvidia,pins = "pbb0",
+						"pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			cam_i2c_scl_pbb1 {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb7 {
+				nvidia,pins = "pbb7",
+						"pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			cam_mclk_pcc0 {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4_rst_n_pcc3 {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pex_l2_rst_n_pcc6 {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+						"pex_l2_clkreq_n_pcc7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pex_wake_n_pdd3 {
+				nvidia,pins = "pex_wake_n_pdd3",
+						"pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			hdmi_cec_pee3 {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			drive_dap1 {
+				nvidia,pins = "drive_dap1",
+						"drive_dap2",
+						"drive_dbg",
+						"drive_at5",
+						"drive_gme",
+						"drive_ddc",
+						"drive_ao1",
+						"drive_uart3";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1",
+						"drive_sdio3";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+			drive_gma {
+				nvidia,pins = "drive_gma",
+						"drive_gmb",
+						"drive_gmc",
+						"drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+		};
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		/* GPS BCM4751 */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		/* Azurewave AW-NH665 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			vbat-supply  = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8>;
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	pwm: pwm@7000a000 {
+		status = "okay";
+	};
+
+	i2c@7000c400 {
+		clock-frequency = <400000>;
+		status = "okay";
+
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_LEVEL_LOW>;
+
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vcc_3v3_ts>;
+			vccio-supply = <&vcc_3v3_ts>;
+
+			touchscreen-size-x = <2112>;
+			touchscreen-size-y = <1280>;
+			touchscreen-swapped-x-y;
+			touchscreen-inverted-x;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <100000>;
+		status = "okay";
+
+		compass@e {
+			compatible = "asahi-kasei,ak8974";
+			reg = <0x0e>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 0) IRQ_TYPE_EDGE_RISING>;
+
+			avdd-supply = <&vdd_3v3_sys>;
+			dvdd-supply = <&vdd_1v8>;
+
+			mount-matrix =	 "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+		};
+
+		light-sensor@1c {
+			compatible = "dynaimage,al3010";
+			reg = <0x1c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+
+		accelerometer@68 {
+			compatible = "invensense,mpu6050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply   = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8>;
+
+			mount-matrix =	 "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+		};
+	};
+
+	i2c@7000d000 {
+		clock-frequency = <100000>;
+		status = "okay";
+
+		rt5640: audio-codec@1c {
+			compatible = "realtek,rt5640";
+			reg = <0x1c>;
+
+			realtek,dmic1-data-pin = <1>;
+		};
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+			vcc-supply = <&vdd_3v3_sys>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 3) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
+		};
+
+		fuel-gauge@55 {
+			compatible = "ti,bq27541";
+			reg = <0x55>;
+			power-supplies = <&power_supply>;
+		};
+
+		power_supply: charger@6a {
+			compatible = "summit,smb347";
+			reg = <0x6a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(V, 1) IRQ_TYPE_EDGE_BOTH>;
+
+			summit,enable-charge-control = <SMB3XX_CHG_ENABLE_PIN_ACTIVE_LOW>;
+			summit,inok-polarity = <SMB3XX_SYSOK_INOK_ACTIVE_LOW>;
+			summit,enable-usb-charging;
+
+			monitored-battery = <&battery_cell>;
+
+			usb_vbus: usb-vbus {
+				regulator-name = "usb_vbus";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-min-microamp = <750000>;
+				regulator-max-microamp = <750000>;
+
+				/*
+				 * SMB347 INOK input pin is connected to PMIC's
+				 * ACOK output, which is fixed to ACTIVE_LOW as
+				 * long as battery voltage is in a good range.
+				 *
+				 * Active INOK disables SMB347 output, so polarity
+				 * needs to be toggled when we want to get the
+				 * output.
+				 */
+				summit,needs-inok-toggle;
+			};
+		};
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <1>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+	};
+
+	ahub@70080000 {
+		i2s@70080400 {
+			status = "okay";
+		};
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_1v8>;
+
+		/* Azurewave AW-NH665 BCM4330 */
+		wifi@1 {
+			reg = <1>;
+			compatible = "brcm,bcm4329-fmac";
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8>;
+		non-removable;
+	};
+
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "otg";
+		vbus-supply = <&usb_vbus>;
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "otg";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		power-supply = <&vdd_5v0_sys>;
+		pwms = <&pwm 0 50000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <15>;
+	};
+
+	battery_cell: battery-cell {
+		compatible = "simple-battery";
+		constant-charge-current-max-microamp = <1800000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	display-panel {
+		/*
+		 * Some device variants come with a Hydis HV070WX2-1E0, but
+		 * since they are all largely compatible, we'll go with the
+		 * Chunghwa one here.
+		 */
+		compatible = "chunghwa,claa070wp03xg", "panel-lvds";
+
+		width-mm = <94>;
+		height-mm = <150>;
+		rotation = <180>;
+
+		data-mapping = "jeida-24";
+
+		/* DDC unconnected on Nexus 7 */
+		/delete-property/ ddc-i2c-bus;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-hall-sensor {
+			label = "Lid";
+			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	vdd_5v0_sys: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <300000>;
+		gpio = <&gpio TEGRA_GPIO(W, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vcc_3v3_ts: regulator-ts {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo_s-1167_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-rt5640-grouper",
+			     "nvidia,tegra-audio-rt5640";
+		nvidia,model = "ASUS Google Nexus 7 ALC5642";
+
+		nvidia,audio-routing =
+			"Headphones", "HPOR",
+			"Headphones", "HPOL",
+			"Speakers", "SPORP",
+			"Speakers", "SPORN",
+			"Speakers", "SPOLP",
+			"Speakers", "SPOLN",
+			"DMIC1", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&rt5640>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents Nexus 7
+		 * from getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
new file mode 100644
index 000000000000..694c7fe37eb8
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/max77620.h>
+
+/ {
+	i2c@7000d000 {
+		pmic: pmic@3c {
+			compatible = "maxim,max77663";
+			reg = <0x3c>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			system-power-controller;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77620_default>;
+
+			cpu-pwr-req-hog {
+				gpio-hog;
+				gpios = <6 GPIO_ACTIVE_HIGH>;
+				input;
+			};
+
+			fps {
+				fps0 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+				};
+
+				fps1 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+				};
+
+				fps2 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+				};
+			};
+
+			max77620_default: pinmux {
+				gpio4 {
+					pins = "gpio4";
+					function = "32k-out1";
+				};
+			};
+
+			regulators {
+				in-sd0-supply = <&vdd_5v0_sys>;
+				in-sd1-supply = <&vdd_5v0_sys>;
+				in-sd2-supply = <&vdd_5v0_sys>;
+				in-sd3-supply = <&vdd_5v0_sys>;
+				in-sd4-supply = <&vdd_5v0_sys>;
+
+				in-ldo0-1-supply = <&vdd_1v35>;
+				in-ldo2-supply   = <&vdd_3v3_sys>;
+				in-ldo3-5-supply = <&vdd_3v3_sys>;
+				in-ldo4-6-supply = <&vdd_5v0_sys>;
+				in-ldo7-8-supply = <&vdd_1v35>;
+
+				vdd_cpu: sd0 {
+					regulator-name = "vdd_cpu";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_core: sd1 {
+					regulator-name = "vdd_core";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-coupled-with = <&vdd_cpu>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
+				};
+
+				vdd_1v8: sd2 {
+					regulator-name = "vdd_gen1v8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_1v35: sd3 {
+					regulator-name = "vdd_ddr3l_1v35";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo0 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo2 {
+					regulator-name = "vdd_ddr_rx";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vcore_emmc: ldo3 {
+					regulator-name = "vcore_emmc";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <3100000>;
+					regulator-always-on;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo5 {
+					regulator-name = "vdd_camera";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo6 {
+					regulator-name = "vddio_sdmmc";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo7 {
+					regulator-name = "avdd_dsi_csi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo8 {
+					regulator-name = "avdd_pll";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		gpio = <&pmic 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	regulator-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd_usb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	pmc@7000e400 {
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x3c>;
+			nvidia,reg-addr = <0x41>;
+			nvidia,reg-data = <0xe0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-memory-timings.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-memory-timings.dtsi
new file mode 100644
index 000000000000..8944a4a5a8d7
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-memory-timings.dtsi
@@ -0,0 +1,1577 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			nvidia,ram-code = <0>; /* Elpida EDJ2108EDBG-DJL-F */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = <
+					0x00020001 /* MC_EMEM_ARB_CFG */
+					0xc0000020 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74830303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = <
+					0x00010001 /* MC_EMEM_ARB_CFG */
+					0xc0000020 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x73430303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0xc0000030 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x72830504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000003 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x72440a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = <
+					0x00000005 /* MC_EMEM_ARB_CFG */
+					0xc000003d /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000008 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0608 /* MC_EMEM_ARB_DA_COVERS */
+					0x70850f09 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = <
+					0x0000000a /* MC_EMEM_ARB_CFG */
+					0xc0000079 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000010 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000b /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b10 /* MC_EMEM_ARB_DA_COVERS */
+					0x70ea1f11 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>; /* Hynix H5TC2G83CFR */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = <
+					0x00020001 /* MC_EMEM_ARB_CFG */
+					0xc0000020 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74830303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = <
+					0x00010001 /* MC_EMEM_ARB_CFG */
+					0xc0000020 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x73430303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0xc0000030 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x72830504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000003 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x72440a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = <
+					0x00000005 /* MC_EMEM_ARB_CFG */
+					0xc000003d /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000008 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0608 /* MC_EMEM_ARB_DA_COVERS */
+					0x70850f09 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = <
+					0x0000000a /* MC_EMEM_ARB_CFG */
+					0xc0000079 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000010 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000b /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b10 /* MC_EMEM_ARB_DA_COVERS */
+					0x70ea1f11 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			nvidia,ram-code = <0>; /* Elpida EDJ2108EDBG-DJL-F */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000004 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000005 /* EMC_TXSR */
+					0x00000005 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000001 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x00000008 /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000009 /* EMC_TXSR */
+					0x00000009 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000005 /* EMC_RC */
+					0x00000010 /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000012 /* EMC_TXSR */
+					0x00000012 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000004 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x0000000a /* EMC_RC */
+					0x00000020 /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000023 /* EMC_TXSR */
+					0x00000023 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000007 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration = <
+					0x0000000f /* EMC_RC */
+					0x00000034 /* EMC_RFC */
+					0x0000000a /* EMC_RAS */
+					0x00000003 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x00000009 /* EMC_W2P */
+					0x00000003 /* EMC_RD_RCD */
+					0x00000003 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x000009e9 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x0000027a /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000e /* EMC_RW2PDEN */
+					0x00000039 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x0000000a /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000a2a /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x002600a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x00014000 /* EMC_DLL_XFORM_DQS4 */
+					0x00014000 /* EMC_DLL_XFORM_DQS5 */
+					0x00014000 /* EMC_DLL_XFORM_DQS6 */
+					0x00014000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x018b000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800014d4 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x0000001f /* EMC_RC */
+					0x00000069 /* EMC_RFC */
+					0x00000017 /* EMC_RAS */
+					0x00000007 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000c /* EMC_W2R */
+					0x00000003 /* EMC_R2P */
+					0x00000011 /* EMC_W2P */
+					0x00000007 /* EMC_RD_RCD */
+					0x00000007 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000b /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001412 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x0000000e /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000c /* EMC_AR2PDEN */
+					0x00000016 /* EMC_RW2PDEN */
+					0x00000072 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000015 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000006 /* EMC_TCLKSTABLE */
+					0x00000007 /* EMC_TCLKSTOP */
+					0x00001453 /* EMC_TREFBW */
+					0x0000000c /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf00b0191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00000008 /* EMC_DLL_XFORM_DQS0 */
+					0x00000008 /* EMC_DLL_XFORM_DQS1 */
+					0x00000008 /* EMC_DLL_XFORM_DQS2 */
+					0x00000008 /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000c /* EMC_DLL_XFORM_DQ0 */
+					0x0000000c /* EMC_DLL_XFORM_DQ1 */
+					0x0000000c /* EMC_DLL_XFORM_DQ2 */
+					0x0000000c /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x0a000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0156000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */
+					0xf8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>; /* Hynix H5TC2G83CFR */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000004 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000005 /* EMC_TXSR */
+					0x00000005 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000001 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x00000008 /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000009 /* EMC_TXSR */
+					0x00000009 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000005 /* EMC_RC */
+					0x00000010 /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000012 /* EMC_TXSR */
+					0x00000012 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000004 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x0000000a /* EMC_RC */
+					0x00000020 /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000023 /* EMC_TXSR */
+					0x00000023 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000007 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration = <
+					0x0000000f /* EMC_RC */
+					0x00000034 /* EMC_RFC */
+					0x0000000a /* EMC_RAS */
+					0x00000003 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x00000009 /* EMC_W2P */
+					0x00000003 /* EMC_RD_RCD */
+					0x00000003 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x000009e9 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x0000027a /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000e /* EMC_RW2PDEN */
+					0x00000039 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x0000000a /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000a2a /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x002600a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x00014000 /* EMC_DLL_XFORM_DQS4 */
+					0x00014000 /* EMC_DLL_XFORM_DQS5 */
+					0x00014000 /* EMC_DLL_XFORM_DQS6 */
+					0x00014000 /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x018b000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800014d4 /* EMC_DYN_SELF_REF_CONTROL */
+					0xf8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000020 /* EMC_RC */
+					0x0000006a /* EMC_RFC */
+					0x00000017 /* EMC_RAS */
+					0x00000007 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000c /* EMC_W2R */
+					0x00000003 /* EMC_R2P */
+					0x00000011 /* EMC_W2P */
+					0x00000007 /* EMC_RD_RCD */
+					0x00000007 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001412 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x0000000e /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000c /* EMC_AR2PDEN */
+					0x00000016 /* EMC_RW2PDEN */
+					0x00000072 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000015 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000006 /* EMC_TCLKSTABLE */
+					0x00000007 /* EMC_TCLKSTOP */
+					0x00001453 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf00b0191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000000a /* EMC_DLL_XFORM_DQS0 */
+					0x0000000a /* EMC_DLL_XFORM_DQS1 */
+					0x0000000a /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000c /* EMC_DLL_XFORM_DQ0 */
+					0x0000000c /* EMC_DLL_XFORM_DQ1 */
+					0x0000000c /* EMC_DLL_XFORM_DQ2 */
+					0x0000000c /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0400013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x0a000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0155000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-ti-pmic.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
new file mode 100644
index 000000000000..ee4a3f482769
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	i2c@7000d000 {
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_sys>;
+			vcc2-supply = <&vdd_5v0_sys>;
+			vcc3-supply = <&vdd_1v8>;
+			vcc4-supply = <&vdd_5v0_sys>;
+			vcc5-supply = <&vdd_5v0_sys>;
+			vcc6-supply = <&vdd2_reg>;
+			vcc7-supply = <&vdd_5v0_sys>;
+			vccio-supply = <&vdd_5v0_sys>;
+
+			regulators {
+				vdd1 {
+					regulator-name = "vddio_ddr_1v2";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				vdd2_reg: vdd2 {
+					regulator-name = "vdd2_1v2";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8: vio {
+					regulator-name = "vdd_1v8_gen";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_pexa,vdd_pexb";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo2 {
+					regulator-name = "vdd_sata,avdd_plle";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+				};
+
+				/* LDO3 is not connected to anything */
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo5 {
+					regulator-name = "vddio_sdmmc,avdd_vdac";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	pmc@7000e400 {
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x80>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper.dtsi
new file mode 100644
index 000000000000..c19a0419112a
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper.dtsi
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "tegra30-asus-nexus7-grouper-common.dtsi"
+#include "tegra30-asus-nexus7-grouper-memory-timings.dtsi"
+
+/ {
+	compatible = "asus,grouper", "nvidia,tegra30";
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_dc1_pd2 {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spi2_cs2_n_pw3 {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_row15_ps7 {
+				nvidia,pins = "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_row13_ps5 {
+				nvidia,pins = "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7",
+						"gmi_wait_pi7",
+						"gmi_cs4_n_pk2",
+						"gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi_cs6_n_pi3 {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	i2c@7000c500 {
+		nfc@28 {
+			compatible = "nxp,pn544-i2c";
+			reg = <0x28>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 0) IRQ_TYPE_EDGE_RISING>;
+
+			enable-gpios   = <&gpio TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+			firmware-gpios = <&gpio TEGRA_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	display-panel {
+		panel-timing {
+			clock-frequency = <68000000>;
+			hactive = <800>;
+			vactive = <1280>;
+			hfront-porch = <24>;
+			hback-porch = <32>;
+			hsync-len = <24>;
+			vsync-len = <1>;
+			vfront-porch = <5>;
+			vback-porch = <32>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-E1565.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-E1565.dts
new file mode 100644
index 000000000000..f1c63feb4af9
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-E1565.dts
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-nexus7-grouper-maxim-pmic.dtsi"
+#include "tegra30-asus-nexus7-tilapia.dtsi"
+
+/ {
+	model = "ASUS Google Nexus 7 (Project Bach / ME370TG) E1565";
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-memory-timings.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-memory-timings.dtsi
new file mode 100644
index 000000000000..9169de34fa00
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-memory-timings.dtsi
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "tegra30-asus-nexus7-grouper-memory-timings.dtsi"
+
+/ {
+	/*
+	 * Tilapia's memory timings are pretty much the same as the Grouper's
+	 * ones. There are few minor tunings made for a higher clock rates,
+	 * these differentiating timings are overridden here for Tilapia.
+	 */
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x0000001f /* EMC_RC */
+					0x00000069 /* EMC_RFC */
+					0x00000017 /* EMC_RAS */
+					0x00000007 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000c /* EMC_W2R */
+					0x00000003 /* EMC_R2P */
+					0x00000011 /* EMC_W2P */
+					0x00000007 /* EMC_RD_RCD */
+					0x00000007 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000b /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001412 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x0000000e /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000c /* EMC_AR2PDEN */
+					0x00000016 /* EMC_RW2PDEN */
+					0x00000072 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000015 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000006 /* EMC_TCLKSTABLE */
+					0x00000007 /* EMC_TCLKSTOP */
+					0x00001453 /* EMC_TREFBW */
+					0x0000000c /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf00b0191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00000008 /* EMC_DLL_XFORM_DQS0 */
+					0x00000008 /* EMC_DLL_XFORM_DQS1 */
+					0x00000008 /* EMC_DLL_XFORM_DQS2 */
+					0x00000008 /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000c /* EMC_DLL_XFORM_DQ0 */
+					0x0000000c /* EMC_DLL_XFORM_DQ1 */
+					0x0000000c /* EMC_DLL_XFORM_DQ2 */
+					0x0000000c /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0156000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration = <
+					0x0000000f /* EMC_RC */
+					0x00000034 /* EMC_RFC */
+					0x0000000a /* EMC_RAS */
+					0x00000003 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x00000009 /* EMC_W2P */
+					0x00000003 /* EMC_RD_RCD */
+					0x00000003 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x000009e9 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x0000027a /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000e /* EMC_RW2PDEN */
+					0x00000039 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x0000000a /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000a2a /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x002600a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x00014000 /* EMC_DLL_XFORM_DQS4 */
+					0x00014000 /* EMC_DLL_XFORM_DQS5 */
+					0x00014000 /* EMC_DLL_XFORM_DQS6 */
+					0x00014000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x018b000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800014d4 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration = <
+					0x00000020 /* EMC_RC */
+					0x0000006a /* EMC_RFC */
+					0x00000017 /* EMC_RAS */
+					0x00000007 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000c /* EMC_W2R */
+					0x00000003 /* EMC_R2P */
+					0x00000011 /* EMC_W2P */
+					0x00000007 /* EMC_RD_RCD */
+					0x00000007 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001412 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000504 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x0000000e /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000c /* EMC_AR2PDEN */
+					0x00000016 /* EMC_RW2PDEN */
+					0x00000072 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000015 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000006 /* EMC_TCLKSTABLE */
+					0x00000007 /* EMC_TCLKSTOP */
+					0x00001453 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf00b0191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00000008 /* EMC_DLL_XFORM_DQS0 */
+					0x00000008 /* EMC_DLL_XFORM_DQS1 */
+					0x00000008 /* EMC_DLL_XFORM_DQS2 */
+					0x00000008 /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000a /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x0c000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0155000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800028a5 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia.dtsi
new file mode 100644
index 000000000000..94c80134574e
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia.dtsi
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "tegra30-asus-nexus7-grouper-common.dtsi"
+#include "tegra30-asus-nexus7-tilapia-memory-timings.dtsi"
+
+/ {
+	compatible = "asus,tilapia", "asus,grouper", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		init-mode-3g-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(P, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 5) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 5) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 0) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(EE, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(Y, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(Y, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(N, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(N, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(N, 0) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(N, 3) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_dc1_pd2 {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spi2_cs2_n_pw3 {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			ulpi_stp_py3 {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_row15_ps7 {
+				nvidia,pins = "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3_sclk_pp3 {
+				nvidia,pins = "dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3",
+						"kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb_row13_ps5 {
+				nvidia,pins = "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7",
+						"gmi_wait_pi7",
+						"gmi_cs4_n_pk2",
+						"gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi_cs6_n_pi3 {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	i2c@7000c500 {
+		proximity-sensor@28 {
+			compatible = "microchip,cap1106";
+			reg = <0x28>;
+
+			/*
+			 * Binding doesn't support specifying linux,input-type
+			 * and this results in unwanted key-presses handled by
+			 * applications, hence keep it disabled for now.
+			 */
+			status = "disabled";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(R, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			linux,keycodes = <KEY_RESERVED>,
+					 <KEY_RESERVED>,
+					 <KEY_RESERVED>,
+					 <KEY_RESERVED>,
+					 <KEY_RESERVED>,
+					 <SW_FRONT_PROXIMITY>;
+		};
+
+		nfc@2a {
+			compatible = "nxp,pn544-i2c";
+			reg = <0x2a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 7) IRQ_TYPE_EDGE_RISING>;
+
+			enable-gpios   = <&gpio TEGRA_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
+			firmware-gpios = <&gpio TEGRA_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	display-panel {
+		enable-gpios = <&gpio TEGRA_GPIO(V, 6) GPIO_ACTIVE_HIGH>;
+
+		panel-timing {
+			clock-frequency = <81750000>;
+			hactive = <800>;
+			vactive = <1280>;
+			hfront-porch = <64>;
+			hback-porch = <128>;
+			hsync-len = <64>;
+			vsync-len = <1>;
+			vfront-porch = <5>;
+			vback-porch = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-tf201.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf201.dts
new file mode 100644
index 000000000000..0406c5a69c12
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf201.dts
@@ -0,0 +1,644 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Prime TF201";
+	compatible = "asus,tf201", "nvidia,tegra30";
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Atmel MXT768E touchscreen */
+		touchscreen@4d {
+			compatible = "atmel,maxtouch";
+			reg = <0x4d>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <100000>;
+
+		magnetometer@e {
+			mount-matrix =  "-1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "1",  "0",  "0",
+							 "0", "-1",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB EDB8132B2MA-8D-F LPDDR2 400MHz */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0x80000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0x80000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0x80000048
+					0x00000002 0x00000003 0x0000000c 0x00000007
+					0x00000009 0x00000001 0x00000002 0x00000006
+					0x00000001 0x00000000 0x00000004 0x00000004
+					0x04040001 0x000d090c 0x71c6120d 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* TF201 Unknown 1GB LPDDR2 500MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0x80000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0x80000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-500000000 {
+				clock-frequency = <500000000>;
+
+				nvidia,emem-configuration = < 0x00000007 0x8000005a
+					0x00000003 0x00000004 0x0000000e 0x00000009
+					0x0000000c 0x00000002 0x00000002 0x00000008
+					0x00000001 0x00000000 0x00000004 0x00000005
+					0x05040001 0x00100a0e 0x71c8170f 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB EDB8132B2MA-8D-F LPDDR2 400MHz */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x00098000 0x00098000 0x00098000
+					0x00098000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000009 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x00098000 0x00098000 0x00098000
+					0x00098000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000018 0x00000018 0x00000018
+					0x00000018 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000009 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000a0000 0x000a0000 0x000a0000
+					0x000a0000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00120220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x00440084
+					0x00008000 0x00074000 0x00074000 0x00074000
+					0x00074000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000018 0x00000018 0x00000018
+					0x00000018 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00078000 0x00078000 0x00078000
+					0x00078000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010082>;
+				nvidia,emc-mode-2 = <0x00020004>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000024>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000017
+					0x00000033 0x00000010 0x00000007 0x00000007
+					0x00000007 0x00000002 0x0000000a 0x00000007
+					0x00000007 0x00000003 0x00000002 0x00000000
+					0x00000003 0x00000007 0x00000004 0x0000000d
+					0x0000000e 0x000005e9 0x00000000 0x0000017a
+					0x00000002 0x00000002 0x00000007 0x00000000
+					0x00000001 0x0000000c 0x00000038 0x00000038
+					0x00000006 0x00000014 0x00000009 0x00000004
+					0x00000002 0x00000680 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0x001d0084
+					0x00008000 0x0002c000 0x0002c000 0x0002c000
+					0x0002c000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000c0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000024 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000ce6 0xe0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* TF201 Unknown 1GB LPDDR2 500MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x00440084
+					0x00008000 0x00060000 0x00060000 0x00060000
+					0x00060000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000d0000 0x000d0000 0x000d0000
+					0x000d0000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-500000000 {
+				clock-frequency = <500000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020005>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000002d>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001d
+					0x00000040 0x00000014 0x00000008 0x00000007
+					0x00000009 0x00000003 0x0000000d 0x00000008
+					0x00000008 0x00000004 0x00000002 0x00000000
+					0x00000004 0x00000008 0x00000005 0x0000000d
+					0x0000000f 0x00000763 0x00000000 0x000001d8
+					0x00000003 0x00000003 0x00000008 0x00000000
+					0x00000001 0x0000000e 0x00000046 0x00000046
+					0x00000008 0x00000019 0x0000000b 0x00000004
+					0x00000002 0x00000820 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0xf0140091
+					0x00008000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x00080220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000b4 0x000d000d 0xa0f10404 0x00000000
+					0x00000000 0x80000fde 0xe0000000 0xff00ff88 >;
+			};
+		};
+	};
+
+	usb-phy@7d000000 {
+		/delete-property/ nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-setup = <5>;      /* Based on TF201 fuse value - 48 */
+	};
+
+	usb-phy@7d008000 {
+		/delete-property/ nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-setup = <5>;      /* Based on TF201 fuse value - 48 */
+	};
+
+	display-panel {
+		compatible = "hannstar,hsd101pww2";
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-533000000;
+		/delete-node/ opp-625000000;
+		/delete-node/ opp-667000000;
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-533000000-1200;
+		/delete-node/ opp-625000000-1200;
+		/delete-node/ opp-625000000-1250;
+		/delete-node/ opp-667000000-1200;
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf201",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Prime TF201 RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-tf300t.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300t.dts
new file mode 100644
index 000000000000..970a1f08dc8c
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300t.dts
@@ -0,0 +1,1032 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Pad TF300T";
+	compatible = "asus,tf300t", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		tf300t-init-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(BB, 5) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech EKTH1036 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2240>;
+			touchscreen-size-y = <1408>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <400000>;
+
+		magnetometer@e {
+			mount-matrix =   "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "-1",  "0",  "0",
+					  "0",  "1",  "0",
+					  "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Wolfson Microelectronics WM8903 audio codec */
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <
+				0x00000600 /* DMIC_LR, output */
+				0x00000680 /* DMIC_DAT, input */
+				0x00000000 /* Speaker-enable GPIO, output, low */
+				0xffffffff /* don't touch */
+				0xffffffff /* don't touch */
+			>;
+
+			AVDD-supply  = <&vdd_1v8_vio>;
+			CPVDD-supply = <&vdd_1v8_vio>;
+			DBVDD-supply = <&vdd_1v8_vio>;
+			DCVDD-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00030003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x00000014 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00030003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0605 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000005
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x00000014 0xc0000079
+					0x00000003 0x00000004 0x00000011 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00140b11 0x70ea1f12 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00140b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x0f000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000003 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000b 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000020
+					0x0000006a 0x00000018 0x00000008 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0155000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xd8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xd8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000016 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000008
+					0x00000008 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xf8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	display-panel {
+		compatible = "innolux,g101ice-l01";
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-wm8903-tf300t",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Asus Transformer Pad TF300T WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"IN2L", "Mic Jack",
+			"DMICDAT", "Int Mic";
+
+		nvidia,audio-codec = <&wm8903>;
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tg.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tg.dts
new file mode 100644
index 000000000000..4861db8e1e59
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tg.dts
@@ -0,0 +1,1104 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Pad 3G TF300TG";
+	compatible = "asus,tf300tg", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		tf300tg-init-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(P, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 5) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 5) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 0) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(Y, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(Y, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(EE, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 3) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_cs2_n_pw3 {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+			};
+
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_stp_py3 {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech EKTH1036 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2240>;
+			touchscreen-size-y = <1408>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <400000>;
+
+		magnetometer@e {
+			mount-matrix =   "1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "-1",  "0",  "0",
+					  "0",  "1",  "0",
+					  "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0x8000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0x80000079
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00050000 0x00050000 0x00050000
+					0x00050000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0a00013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x0a000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000020
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00040000 0x00040000 0x00040000
+					0x00040000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000016 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0600013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	display-panel {
+		compatible = "innolux,g101ice-l01";
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf300tg",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Pad TF300TG RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-tf700t.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf700t.dts
new file mode 100644
index 000000000000..9c480fde2e76
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf700t.dts
@@ -0,0 +1,840 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+
+/ {
+	model = "Asus Transformer Infinity TF700T";
+	compatible = "asus,tf700t", "nvidia,tegra30";
+
+	host1x@50000000 {
+		lcd: dc@54200000 {
+			clocks = <&tegra_car TEGRA30_CLK_DISP1>,
+				 <&tegra_car TEGRA30_CLK_PLL_D_OUT0>;
+
+			rgb {
+				status = "okay";
+
+				port {
+					dpi_output: endpoint {
+						remote-endpoint = <&bridge_input>;
+						bus-width = <24>;
+					};
+				};
+			};
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH665 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech ELAN-3024-7053 or 5184N FPC-1 REV: 2/3 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2944>;
+			touchscreen-size-y = <1856>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <100000>;
+
+		magnetometer@e {
+			mount-matrix =   "1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Micron 1GB 800MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x75830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74630303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000002 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x73c30504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000004 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x73840a06 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000007 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086120a 0x001f0000 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emem-configuration = < 0x0000000c 0xc0000090
+					0x00000004 0x00000005 0x00000013 0x0000000c
+					0x0000000f 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d13 0x712c2414 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Elpida 1GB 800MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x75830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74630303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000002 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x73c30504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000004 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x73840a06 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000007 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086120a 0x001f0000 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emem-configuration = < 0x0000000c 0xc0000090
+					0x00000004 0x00000005 0x00000013 0x0000000c
+					0x0000000f 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d13 0x712c2414 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Micron 1GB 800MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000006 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000007 0x00000007
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000d 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000000e 0x0000000e
+					0x00000004 0x00000003 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001a 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000001c 0x0000001c
+					0x00000004 0x00000005 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000035 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000038 0x00000038
+					0x00000004 0x00000009 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000012
+					0x00000066 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000bf0 0x00000000 0x000002fc
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000008 0x0000000f 0x0000006c 0x00000200
+					0x00000004 0x00000010 0x00000000 0x00000004
+					0x00000005 0x00000c30 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x001d0084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0600013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0158000c 0xa0f10000 0x00000000
+					0x00000000 0x800018c8 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000025
+					0x000000ce 0x0000001a 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000004 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001820 0x00000000 0x00000608
+					0x00000003 0x00000012 0x00000001 0x00000000
+					0x0000000f 0x00000018 0x000000d8 0x00000200
+					0x00000005 0x00000020 0x00000000 0x00000007
+					0x00000008 0x00001860 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf0070191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00f0000c 0xa0f10000 0x00000000
+					0x00000000 0x8000308c 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Elpida 1GB 800MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000006 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000007 0x00000007
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000d 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000000e 0x0000000e
+					0x00000004 0x00000003 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001a 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000001c 0x0000001c
+					0x00000004 0x00000005 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000035 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000038 0x00000038
+					0x00000004 0x00000009 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000012
+					0x00000066 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000bf0 0x00000000 0x000002fc
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000008 0x0000000f 0x0000006c 0x00000200
+					0x00000004 0x00000010 0x00000000 0x00000004
+					0x00000005 0x00000c30 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x001d0084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0600013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0158000c 0xa0f10000 0x00000000
+					0x00000000 0x800018c8 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000025
+					0x000000ce 0x0000001a 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000004 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001820 0x00000000 0x00000608
+					0x00000003 0x00000012 0x00000001 0x00000000
+					0x0000000f 0x00000018 0x000000d8 0x00000200
+					0x00000005 0x00000020 0x00000000 0x00000007
+					0x00000008 0x00001860 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf0070191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0a00013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00f0000c 0xa0f10000 0x00000000
+					0x00000000 0x8000308c 0xe8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	tc358768_refclk: clock-tc358768 {
+		compatible = "fixed-clock";
+		clock-frequency = <23100000>;
+		clock-accuracy = <100>;
+		#clock-cells = <0>;
+	};
+
+	tc358768_osc: clock-tc358768-osc-gate {
+		compatible = "gpio-gate-clock";
+		enable-gpios = <&gpio TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>;
+		clocks = <&tc358768_refclk>;
+		#clock-cells = <0>;
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux-gpio";
+
+		mux-gpios = <&gpio TEGRA_GPIO(X, 0) GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&lcd_ddc>;
+		idle-state = <0x0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsi@7 {
+				compatible = "toshiba,tc358768";
+				reg = <0x7>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				clocks = <&tc358768_osc>;
+				clock-names = "refclk";
+
+				reset-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_LOW>;
+
+				vddc-supply = <&vdd_1v2_mipi>;
+				vddio-supply = <&vdd_1v8_vio>;
+				vddmipi-supply = <&vdd_1v2_mipi>;
+
+				/*
+				 * Panasonic VVX10F004B00 or HYDIS HV101WU1-1E1
+				 * LCD SuperIPS+ Full HD panel.
+				 */
+				panel@1 {
+					compatible = "panasonic,vvx10f004b00";
+					reg = <1>;
+
+					power-supply = <&vdd_pnl>;
+					backlight = <&backlight>;
+
+					port {
+						panel_input: endpoint {
+							remote-endpoint = <&bridge_output>;
+						};
+					};
+				};
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						bridge_input: endpoint {
+							remote-endpoint = <&dpi_output>;
+							data-lines = <24>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						bridge_output: endpoint {
+							remote-endpoint = <&panel_input>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-900000000-1350;
+	};
+
+	vdd_1v2_mipi: regulator-mipi {
+		compatible = "regulator-fixed";
+		regulator-name = "tc358768_1v2_vdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-enable-ramp-delay = <10000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf700t",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Infinity TF700T RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-transformer-common.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-transformer-common.dtsi
new file mode 100644
index 000000000000..ead95306840f
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-transformer-common.dtsi
@@ -0,0 +1,1790 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+
+/ {
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = "/mmc@78000600"; /* eMMC */
+		mmc1 = "/mmc@78000000"; /* uSD slot */
+		mmc2 = "/mmc@78000400"; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		display0 = &lcd;
+		display1 = &hdmi;
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;		/* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@beb00000 {
+			compatible = "ramoops";
+			reg = <0xbeb00000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;	/* 2MB */
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi: hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&vdd_1v8_vio>;
+			vdd-supply = <&vdd_3v3_sys>;
+
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+		};
+	};
+
+	gpio@6000d000 {
+		init-lpm-in-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
+			input;
+		};
+
+		init-lpm-out-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(K, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+
+		usb-charge-limit-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			output-high;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* SDMMC1 pinmux */
+			sdmmc1_clk {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_cmd {
+				nvidia,pins = "sdmmc1_dat3_py4",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat0_py7",
+						"sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_cd {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_wp {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC2 pinmux */
+			vi_d1_pd5 {
+				nvidia,pins = "vi_d1_pd5",
+						"vi_d2_pl0",
+						"vi_d3_pl1",
+						"vi_d5_pl3",
+						"vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d8_pl6 {
+				nvidia,pins = "vi_d8_pl6",
+						"vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* SDMMC3 pinmux */
+			sdmmc3_clk {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat3_pb4",
+						"sdmmc3_dat4_pd1",
+						"sdmmc3_dat5_pd0",
+						"sdmmc3_dat6_pd3",
+						"sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC4 pinmux */
+			sdmmc4_clk {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_cmd {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_rst_n {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			cam_mclk {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			drive_sdmmc4 {
+				nvidia,pins = "drive_gma",
+						"drive_gmb",
+						"drive_gmc",
+						"drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			/* I2C pinmux */
+			gen1_i2c {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			gen2_i2c {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			cam_i2c {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			ddc_i2c {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			pwr_i2c {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			hotplug_i2c {
+				nvidia,pins = "pu4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI pinmux */
+			hdmi_cec {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			hdmi_hpd {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-A */
+			ulpi_data0_po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data1_po2 {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data5_po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0",
+						"ulpi_data2_po3",
+						"ulpi_data3_po4",
+						"ulpi_data4_po5",
+						"ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-B */
+			uartb_txd_rts {
+				nvidia,pins = "uart2_txd_pc2",
+						"uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uartb_rxd_cts {
+				nvidia,pins = "uart2_rxd_pc3",
+						"uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-C */
+			uartc_rxd_cts {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uartc_txd_rts {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-D */
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0",
+						"ulpi_dir_py1",
+						"ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* I2S pinmux */
+			dap_i2s0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_din_pn1",
+						"dap1_dout_pn2",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap_i2s1 {
+				nvidia,pins = "dap2_fs_pa2",
+						"dap2_sclk_pa3",
+						"dap2_din_pa4",
+						"dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_fs {
+				nvidia,pins = "dap3_fs_pp0",
+						"dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_dout {
+				nvidia,pins = "dap3_dout_pp2",
+						"dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap_i2s3 {
+				nvidia,pins = "dap4_fs_pp4",
+						"dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			nct_irq {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Asus EC pinmux */
+			ec_irqs {
+				nvidia,pins = "kb_row10_ps2",
+						"kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ec_reqs {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Memory type bootstrap */
+			mem_boostraps {
+				nvidia,pins = "gmi_ad4_pg4",
+						"gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PCI-e pinmux */
+			pex_l2_rst_n {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+						"pex_l0_rst_n_pdd1",
+						"pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_clkreq_n {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7",
+						"pex_l0_prsnt_n_pdd0",
+						"pex_l0_clkreq_n_pdd2",
+						"pex_wake_n_pdd3",
+						"pex_l1_prsnt_n_pdd4",
+						"pex_l1_clkreq_n_pdd6",
+						"pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SPI pinmux */
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4",
+						"spi1_sck_px5",
+						"spi1_cs0_n_px6",
+						"spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			hp_detect {
+				nvidia,pins = "spi2_cs1_n_pw2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			mic_detect {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+						"gmi_a16_pj7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_a18_pb1 {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a19_pk7 {
+				nvidia,pins = "gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Display A pinmux */
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+						"lcd_pclk_pb3",
+						"lcd_pwr1_pc1",
+						"lcd_d0_pe0",
+						"lcd_d1_pe1",
+						"lcd_d2_pe2",
+						"lcd_d3_pe3",
+						"lcd_d4_pe4",
+						"lcd_d5_pe5",
+						"lcd_d6_pe6",
+						"lcd_d7_pe7",
+						"lcd_d8_pf0",
+						"lcd_d9_pf1",
+						"lcd_d10_pf2",
+						"lcd_d11_pf3",
+						"lcd_d12_pf4",
+						"lcd_d13_pf5",
+						"lcd_d14_pf6",
+						"lcd_d15_pf7",
+						"lcd_de_pj1",
+						"lcd_hsync_pj3",
+						"lcd_vsync_pj4",
+						"lcd_d16_pm0",
+						"lcd_d17_pm1",
+						"lcd_d18_pm2",
+						"lcd_d19_pm3",
+						"lcd_d20_pm4",
+						"lcd_d21_pm5",
+						"lcd_d22_pm6",
+						"lcd_d23_pm7",
+						"lcd_dc0_pn6",
+						"lcd_sdin_pz2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_cs0_n_pn4 {
+				nvidia,pins = "lcd_cs0_n_pn4",
+						"lcd_sdout_pn5",
+						"lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			blink {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC keys */
+			kb_col0_pq0 {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col1_pq1 {
+				nvidia,pins = "kb_row1_pr1",
+						"kb_row3_pr3",
+						"kb_row8_ps0",
+						"kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_col4_pq4 {
+				nvidia,pins = "kb_col4_pq4",
+						"kb_col5_pq5",
+						"kb_col7_pq7",
+						"kb_row2_pr2",
+						"kb_row4_pr4",
+						"kb_row5_pr5",
+						"kb_row12_ps4",
+						"kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7",
+						"gmi_wait_pi7",
+						"gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs0_n_pj0 {
+				nvidia,pins = "gmi_cs0_n_pj0",
+						"gmi_cs1_n_pj2",
+						"gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_pclk_pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* GPIO keys pinmux */
+			power_key {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vol_keys {
+				nvidia,pins = "kb_col2_pq2",
+						"kb_col3_pq3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Bluetooth */
+			bt_shutdown {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			bt_dev_wake {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			bt_host_wake {
+				nvidia,pins = "pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv2 {
+				nvidia,pins = "pv2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_vsync_pd6 {
+				nvidia,pins = "vi_vsync_pd6",
+						"vi_hsync_pd7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			vi_d10_pt2 {
+				nvidia,pins = "vi_d10_pt2",
+						"vi_d0_pt4", "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+						"gmi_ad1_pg1",
+						"gmi_ad2_pg2",
+						"gmi_ad3_pg3",
+						"gmi_ad6_pg6",
+						"gmi_ad7_pg7",
+						"gmi_wr_n_pi0",
+						"gmi_oe_n_pi1",
+						"gmi_dqs_pi2",
+						"gmi_adv_n_pk0",
+						"gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+						"gmi_ad11_ph3",
+						"gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad12_ph4 {
+				nvidia,pins = "gmi_ad12_ph4",
+						"gmi_rst_n_pi4",
+						"gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Vibrator control */
+			vibrator {
+				nvidia,pins = "gmi_ad15_ph7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* PWM pimnmux */
+			pwm_0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwm_2 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs6_n_pi3 {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Spdif pinmux */
+			spdif_out {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_in {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d4_pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d6_pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			vi_mclk_pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag_rtck {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6",
+						"crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1_out {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_out {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_out {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sys_clk_req {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5",
+						"clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive_dap1 {
+				nvidia,pins = "drive_dap1",
+						"drive_dap2",
+						"drive_dbg",
+						"drive_at5",
+						"drive_gme",
+						"drive_ddc",
+						"drive_ao1",
+						"drive_uart3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1",
+						"drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+		};
+	};
+
+	serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Broadcom GPS BCM47511 */
+	};
+
+	serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		bluetooth {
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+
+			vbat-supply  = <&vdd_3v3_com>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	lcd_ddc: i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+
+		/* Aichi AMI306 digital compass */
+		magnetometer@e {
+			compatible = "asahi-kasei,ak8974";
+			reg = <0x0e>;
+
+			avdd-supply = <&vdd_3v3_sys>;
+			dvdd-supply = <&vdd_1v8_vio>;
+		};
+
+		/* Dynaimage ambient light sensor */
+		light-sensor@1c {
+			compatible = "dynaimage,al3010";
+			reg = <0x1c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply    = <&vdd_3v3_sys>;
+			vlogic-supply = <&vdd_1v8_vio>;
+
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0x0f>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(O, 5) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_1v8_vio>;
+					vddio-supply = <&vdd_1v8_vio>;
+				};
+			};
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <93750>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Texas Instruments TPS659110 PMIC */
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_bat>;
+			vcc2-supply = <&vdd_5v0_bat>;
+			vcc3-supply = <&vdd_1v8_vio>;
+			vcc4-supply = <&vdd_5v0_sys>;
+			vcc5-supply = <&vdd_5v0_bat>;
+			vcc6-supply = <&vdd_3v3_sys>;
+			vcc7-supply = <&vdd_5v0_bat>;
+			vccio-supply = <&vdd_5v0_bat>;
+
+			pmic-sleep-hog {
+				gpio-hog;
+				gpios = <2 GPIO_ACTIVE_HIGH>;
+				output-high;
+			};
+
+			regulators {
+				/* VDD1 is not used by Transformers */
+
+				vddio_ddr: vdd2 {
+					regulator-name = "vddio_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8_vio: vio {
+					regulator-name = "vdd_1v8_gen";
+					/* FIXME: eMMC won't work, if set to 1.8 V */
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* eMMC VDD */
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_emmc_core";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDD */
+				vdd_usd: ldo2 {
+					regulator-name = "vdd_usd";
+					regulator-min-microvolt = <3100000>;
+					regulator-max-microvolt = <3100000>;
+					/* FIXME: Without this, voltage switching fails */
+					regulator-always-on;
+				};
+
+				/* uSD slot VDDIO */
+				vddio_usd: ldo3 {
+					regulator-name = "vddio_usd";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3100000>;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				/* LDO5 is not used by Transformers */
+
+				ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1770000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		/* FIXME: LP1 doesn't work at the moment */
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		/* Set DEV_OFF + PWR_OFF_SET bit in DCDC control register of TPS65911 PMIC  */
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x81>;
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		i2s@70080400 {		/* i2s1 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 {		/* i2s3 */
+			status = "okay";
+		};
+	};
+
+	mmc@78000000 {
+		status = "okay";
+
+		/* FIXME: Full 208Mhz clock rate doesn't work reliably */
+		max-frequency = <104000000>;
+
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		bus-width = <4>;
+
+		vmmc-supply = <&vdd_usd>;	/* ldo2 */
+		vqmmc-supply = <&vddio_usd>;	/* ldo3 */
+	};
+
+	mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_com>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* Azurewave AW-NH615 BCM4329B1 or AW-NH665 BCM4330B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+		mmc-ddr-3_3v;
+		non-removable;
+	};
+
+	/* USB via ASUS connector */
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	/* Dock's USB port */
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_bat>;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_bl>;
+		pwms = <&pwm 0 4000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <40>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+
+		switch-dock-hall-sensor {
+			label = "Lid sensor";
+			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-lineout-detect {
+			label = "Audio dock line-out detect";
+			gpios = <&gpio TEGRA_GPIO(X, 3) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LINEOUT_INSERT>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	vdd_5v0_bat: regulator-bat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ac_bat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_5v0_cp: regulator-sby {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sby";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_5v0_sys: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_1v5_ddr: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_3v3_sys: regulator-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <20000>;
+		gpio = <&gpio TEGRA_GPIO(W, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_3v3_com: regulator-com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_5v0_bl: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	sound {
+		nvidia,i2s-controller = <&tegra_i2s1>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,mic-det-gpios = <&gpio TEGRA_GPIO(X, 2) GPIO_ACTIVE_LOW>;
+		nvidia,coupled-mic-hp-det;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * Transformers from getting too hot from a user's
+		 * tactile perspective. The CPU zone is intended to
+		 * protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 75C until temperature drops to 74.8C */
+					temperature = <75000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-beaver.dts b/arch/arm/boot/dts/nvidia/tegra30-beaver.dts
index a3b0f3555cd2..1d74179dde79 100644
--- a/arch/arm/boot/dts/tegra30-beaver.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-beaver.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 
 #include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
 
 / {
 	model = "NVIDIA Tegra30 Beaver evaluation board";
@@ -1731,6 +1733,8 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -1774,6 +1778,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
+			wakeup-source;
 
 			ti,system-power-controller;
 
@@ -1806,9 +1811,14 @@
 
 				vddctrl_reg: vddctrl {
 					regulator-name = "vdd_cpu,vdd_sys";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&core_vdd_reg>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
 					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				vio_reg: vio {
@@ -1868,24 +1878,30 @@
 			};
 		};
 
-		tps62361@60 {
+		core_vdd_reg: tps62361@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
 
 			regulator-name = "tps62361-vout";
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1500000>;
+			regulator-coupled-with = <&vddctrl_reg>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
 			regulator-boot-on;
 			regulator-always-on;
 			ti,vsel0-state-high;
 			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
 		};
 	};
 
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@1 {
+
+		flash@1 {
 			compatible = "winbond,w25q32", "jedec,spi-nor";
 			reg = <1>;
 			spi-max-frequency = <20000000>;
@@ -1902,6 +1918,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&core_vdd_reg>;
 	};
 
 	ahub@70080000 {
@@ -1910,7 +1927,7 @@
 		};
 	};
 
-	sdhci@78000000 {
+	mmc@78000000 {
 		status = "okay";
 		vqmmc-supply = <&ldo5_reg>;
 		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
@@ -1919,7 +1936,7 @@
 		bus-width = <4>;
 	};
 
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -1953,16 +1970,31 @@
 		status = "okay";
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@1 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@2 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
 
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+		cpu@3 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};
 
@@ -1979,118 +2011,103 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_5v_in_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd_5v_in";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_5v_in_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v_in";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		chargepump_5v_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "chargepump_5v";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-boot-on;
-			regulator-always-on;
-			enable-active-high;
-			gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
-		};
+	chargepump_5v_reg: regulator-chargepump {
+		compatible = "regulator-fixed";
+		regulator-name = "chargepump_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+	};
 
-		ddr_reg: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vdd_ddr";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
-			vin-supply = <&vdd_5v_in_reg>;
-		};
+	ddr_reg: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vdd_5v_in_reg>;
+	};
 
-		vdd_5v_sata_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vdd_5v_sata";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(D, 6) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&vdd_5v_in_reg>;
-		};
+	vdd_5v_sata_reg: regulator-sata {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v_sata";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(D, 6) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vdd_5v_in_reg>;
+	};
 
-		usb1_vbus_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(DD, 6) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v_in_reg>;
-		};
+	usb1_vbus_reg: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 6) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v_in_reg>;
+	};
 
-		usb3_vbus_reg: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "usb3_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v_in_reg>;
-		};
+	usb3_vbus_reg: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v_in_reg>;
+	};
 
-		sys_3v3_reg: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "sys_3v3,vdd_3v3_alw";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
-			vin-supply = <&vdd_5v_in_reg>;
-		};
+	sys_3v3_reg: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "sys_3v3,vdd_3v3_alw";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vdd_5v_in_reg>;
+	};
 
-		sys_3v3_pexs_reg: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "sys_3v3_pexs";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	sys_3v3_pexs_reg: regulator-pexs {
+		compatible = "regulator-fixed";
+		regulator-name = "sys_3v3_pexs";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_5v0_hdmi: regulator@8 {
-			compatible = "regulator-fixed";
-			reg = <8>;
-			regulator-name = "+VDD_5V_HDMI";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_5v0_hdmi: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "+VDD_5V_HDMI";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&sys_3v3_reg>;
 	};
 
 	sound {
@@ -2111,7 +2128,13 @@
 
 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA30_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra30-cardhu-a02.dts b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a02.dts
new file mode 100644
index 000000000000..247185314f46
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a02.dts
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-cardhu.dtsi"
+
+/* This dts file support the cardhu A02 version of board */
+
+/ {
+	model = "NVIDIA Tegra30 Cardhu A02 evaluation board";
+	compatible = "nvidia,cardhu-a02", "nvidia,cardhu", "nvidia,tegra30";
+
+	mmc@78000400 {
+		status = "okay";
+		power-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		bus-width = <4>;
+		keep-power-in-suspend;
+	};
+
+	ddr_reg: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	sys_3v3_reg: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "sys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	usb1_vbus_reg: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(I, 4) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_reg>;
+	};
+
+	usb3_vbus_reg: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_reg>;
+	};
+
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_bl_reg: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(K, 3) GPIO_ACTIVE_HIGH>;
+	};
+};
+
diff --git a/arch/arm/boot/dts/nvidia/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a04.dts
new file mode 100644
index 000000000000..2911f08863a0
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a04.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-cardhu.dtsi"
+
+/* This dts file support the cardhu A04 and later versions of board */
+
+/ {
+	model = "NVIDIA Tegra30 Cardhu A04 (A05, A06, A07) evaluation board";
+	compatible = "nvidia,cardhu-a04", "nvidia,cardhu", "nvidia,tegra30";
+
+	mmc@78000400 {
+		status = "okay";
+		power-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
+		bus-width = <4>;
+		keep-power-in-suspend;
+	};
+
+	ddr_reg: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	sys_3v3_reg: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "sys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	usb1_vbus_reg: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 6) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_reg>;
+	};
+
+	usb3_vbus_reg: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_reg>;
+	};
+
+	vdd_5v0_reg: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_bl_reg: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 2) GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_bl2_reg: regulator-bl2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_bl2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/nvidia/tegra30-cardhu.dtsi
index 7ce61edd52f5..0120859d6d72 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-cardhu.dtsi
@@ -1,6 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
 
 /**
  * This file contains common DT entry for all fab version of Cardhu.
@@ -167,11 +170,15 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
@@ -206,7 +213,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x70>;
-			reset-gpio = <&gpio TEGRA_GPIO(BB, 0) GPIO_ACTIVE_LOW>;
+			reset-gpios = <&gpio TEGRA_GPIO(BB, 0) GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -240,6 +247,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
+			wakeup-source;
 
 			ti,system-power-controller;
 
@@ -272,9 +280,14 @@
 
 				vddctrl_reg: vddctrl {
 					regulator-name = "vdd_cpu,vdd_sys";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
 					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				vio_reg: vio {
@@ -334,32 +347,39 @@
 			};
 		};
 
-		temperature-sensor@4c {
+		nct1008: temperature-sensor@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
 			vcc-supply = <&sys_3v3_reg>;
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+			#thermal-sensor-cells = <1>;
 		};
 
-		tps62361@60 {
+		vdd_core: tps62361@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
 
 			regulator-name = "tps62361-vout";
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1500000>;
+			regulator-coupled-with = <&vddctrl_reg>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
 			regulator-boot-on;
 			regulator-always-on;
 			ti,vsel0-state-high;
 			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
 		};
 	};
 
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@1 {
+
+		flash@1 {
 			compatible = "winbond,w25q32", "jedec,spi-nor";
 			reg = <1>;
 			spi-max-frequency = <20000000>;
@@ -376,6 +396,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	ahub@70080000 {
@@ -384,7 +405,7 @@
 		};
 	};
 
-	sdhci@78000000 {
+	mmc@78000000 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(T, 3) GPIO_ACTIVE_HIGH>;
@@ -392,7 +413,7 @@
 		bus-width = <4>;
 	};
 
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -418,21 +439,67 @@
 		default-brightness-level = <6>;
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			interrupt-parent = <&pmic>;
+			interrupts = <2 0>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <100>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+		};
 
-		clk32k_in: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
 		};
 	};
 
 	panel: panel {
-		compatible = "chunghwa,claa101wb01", "simple-panel";
+		compatible = "chunghwa,claa101wb01";
 		ddc-i2c-bus = <&panelddc>;
 
 		power-supply = <&vdd_pnl1_reg>;
@@ -441,158 +508,139 @@
 		backlight = <&backlight>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_ac_bat_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd_ac_bat";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	vdd_ac_bat_reg: regulator-acbat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ac_bat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		cam_1v8_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "cam_1v8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(BB, 4) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&vio_reg>;
-		};
+	cam_1v8_reg: regulator-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(BB, 4) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vio_reg>;
+	};
 
-		cp_5v_reg: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "cp_5v";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-boot-on;
-			regulator-always-on;
-			enable-active-high;
-			gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
-		};
+	cp_5v_reg: regulator-5v0cp {
+		compatible = "regulator-fixed";
+		regulator-name = "cp_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+	};
 
-		emmc_3v3_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "emmc_3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(D, 1) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	emmc_3v3_reg: regulator-emmc {
+		compatible = "regulator-fixed";
+		regulator-name = "emmc_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(D, 1) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		modem_3v3_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "modem_3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(D, 6) GPIO_ACTIVE_HIGH>;
-		};
+	modem_3v3_reg: regulator-modem {
+		compatible = "regulator-fixed";
+		regulator-name = "modem_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(D, 6) GPIO_ACTIVE_HIGH>;
+	};
 
-		pex_hvdd_3v3_reg: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "pex_hvdd_3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	pex_hvdd_3v3_reg: regulator-pex {
+		compatible = "regulator-fixed";
+		regulator-name = "pex_hvdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_cam1_ldo_reg: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "vdd_cam1_ldo";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(R, 6) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_cam1_ldo_reg: regulator-cam1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_cam1_ldo";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(R, 6) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_cam2_ldo_reg: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "vdd_cam2_ldo";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_cam2_ldo_reg: regulator-cam2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_cam2_ldo";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_cam3_ldo_reg: regulator@8 {
-			compatible = "regulator-fixed";
-			reg = <8>;
-			regulator-name = "vdd_cam3_ldo";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_cam3_ldo_reg: regulator-cam3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_cam3_ldo";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_com_reg: regulator@9 {
-			compatible = "regulator-fixed";
-			reg = <9>;
-			regulator-name = "vdd_com";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_com_reg: regulator-com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_fuse_3v3_reg: regulator@10 {
-			compatible = "regulator-fixed";
-			reg = <10>;
-			regulator-name = "vdd_fuse_3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(L, 6) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_fuse_3v3_reg: regulator-fuse {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_fuse_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(L, 6) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_pnl1_reg: regulator@11 {
-			compatible = "regulator-fixed";
-			reg = <11>;
-			regulator-name = "vdd_pnl1";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
-			vin-supply = <&sys_3v3_reg>;
-		};
+	vdd_pnl1_reg: regulator-pnl1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_pnl1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
 
-		vdd_vid_reg: regulator@12 {
-			compatible = "regulator-fixed";
-			reg = <12>;
-			regulator-name = "vddio_vid";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(T, 0) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_reg>;
-		};
+	vdd_vid_reg: regulator-vid {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio_vid";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(T, 0) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_reg>;
 	};
 
 	sound {
@@ -615,38 +663,52 @@
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
-			GPIO_ACTIVE_HIGH>;
+			GPIO_ACTIVE_LOW>;
 
 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA30_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
 
-		power {
-			label = "Power";
-			interrupt-parent = <&pmic>;
-			interrupts = <2 0>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <100>;
-			wakeup-source;
-		};
+			thermal-sensors = <&nct1008 1>;
 
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <10>;
-		};
+			trips {
+				trip0: cpu-alert0 {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
 
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <10>;
+				trip1: cpu-crit {
+					/* shut down at 60C */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts b/arch/arm/boot/dts/nvidia/tegra30-colibri-eval-v3.dts
index 5965150ecdd2..1990bf8e122d 100644
--- a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-colibri-eval-v3.dts
@@ -38,6 +38,8 @@
 
 	/* Colibri UART-A */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -98,7 +100,7 @@
 	};
 
 	/* SD/MMC */
-	sdhci@78000200 {
+	mmc@78000200 {
 		status = "okay";
 		bus-width = <4>;
 		cd-gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_LOW>; /* MMCD */
@@ -136,7 +138,7 @@
 		pwms = <&pwm 0 5000000>; /* PWM<A> */
 	};
 
-	clk16m: osc3 {
+	clk16m: clock-osc3 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <16000000>;
@@ -145,7 +147,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
@@ -159,7 +161,7 @@
 		 * edt,et057090dhu: EDT 5.7" LCD TFT
 		 * edt,et070080dh6: EDT 7.0" LCD TFT
 		 */
-		compatible = "edt,et057090dhu", "simple-panel";
+		compatible = "edt,et057090dhu";
 		backlight = <&backlight>;
 		power-supply = <&reg_3v3>;
 	};
diff --git a/arch/arm/boot/dts/tegra30-colibri.dtsi b/arch/arm/boot/dts/nvidia/tegra30-colibri.dtsi
index 1f9198bb24ff..4eb526fe9c55 100644
--- a/arch/arm/boot/dts/tegra30-colibri.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-colibri.dtsi
@@ -20,6 +20,15 @@
 		};
 	};
 
+	gpio: gpio@6000d000 {
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET#";
+		};
+	};
+
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -239,7 +248,7 @@
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 			};
 			spdif-in-pk6 {
-				nvidia,pins =	"spdif_in_pk6";
+				nvidia,pins = "spdif_in_pk6";
 				nvidia,function = "hda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -364,7 +373,7 @@
 			};
 			/* Multiplexed and therefore disabled */
 			cam-mclk-pcc0 {
-				nvidia,pins =	"cam_mclk_pcc0";
+				nvidia,pins = "cam_mclk_pcc0";
 				nvidia,function = "vi_alt3";
 				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -511,7 +520,7 @@
 
 			/* Colibri USBC_DET */
 			spdif-out-pk5 {
-				nvidia,pins =	"spdif_out_pk5";
+				nvidia,pins = "spdif_out_pk5";
 				nvidia,function = "rsvd2";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -527,7 +536,7 @@
 			};
 
 			/* Colibri USBH_OC */
-			spi2-cs2-n-pw3, {
+			spi2-cs2-n-pw3 {
 				nvidia,pins = "spi2_cs2_n_pw3";
 				nvidia,function = "spi2_alt";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -701,10 +710,14 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -723,6 +736,7 @@
 		sgtl5000: codec@a {
 			compatible = "fsl,sgtl5000";
 			reg = <0x0a>;
+			#sound-dai-cells = <0>;
 			VDDA-supply = <&reg_module_3v3_audio>;
 			VDDD-supply = <&reg_1v8_vio>;
 			VDDIO-supply = <&reg_module_3v3>;
@@ -736,6 +750,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
+			wakeup-source;
 
 			ti,system-power-controller;
 
@@ -763,9 +778,14 @@
 
 				vddctrl_reg: vddctrl {
 					regulator-name = "+V1.0_VDD_CPU";
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
 					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				reg_1v8_vio: vio {
@@ -840,7 +860,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			interrupt-controller;
 			id = <0>;
 			blocks = <0x5>;
@@ -855,6 +875,11 @@
 			st,sample-time = <4>;
 			/* forbid to use ADC channels 3-0 (touch) */
 
+			stmpe_adc {
+				compatible = "st,stmpe-adc";
+				st,norequest-mask = <0x0F>;
+			};
+
 			stmpe_touchscreen {
 				compatible = "st,stmpe-ts";
 				/* 8 sample average control */
@@ -871,11 +896,6 @@
 				/* 5 ms touch detect interrupt delay */
 				st,touch-det-delay = <5>;
 			};
-
-			stmpe_adc {
-				compatible = "st,stmpe-adc";
-				st,norequest-mask = <0x0F>;
-			};
 		};
 
 		/*
@@ -888,18 +908,20 @@
 		};
 
 		/* SW: +V1.2_VDD_CORE */
-		regulator@60 {
+		vdd_core: regulator@60 {
 			compatible = "ti,tps62362";
 			reg = <0x60>;
 
 			regulator-name = "tps62362-vout";
 			regulator-min-microvolt = <900000>;
 			regulator-max-microvolt = <1400000>;
+			regulator-coupled-with = <&vddctrl_reg>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
 			regulator-boot-on;
 			regulator-always-on;
-			ti,vsel0-state-low;
-			/* VSEL1: EN_CORE_DVFS_N low for DVFS */
-			ti,vsel1-state-low;
+
+			nvidia,tegra-core-regulator;
 		};
 	};
 
@@ -912,6 +934,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 
 		/* Set DEV_OFF bit in DCDC control register of TPS65911 PMIC */
 		i2c-thermtrip {
@@ -933,7 +956,7 @@
 	};
 
 	/* eMMC */
-	sdhci@78000600 {
+	mmc@78000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -948,7 +971,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		asix@1 {
+		ethernet@1 {
+			compatible = "usbb95,772b";
 			reg = <1>;
 			local-mac-address = [00 00 00 00 00 00];
 		};
@@ -959,7 +983,7 @@
 		vbus-supply = <&reg_lan_v_bus>;
 	};
 
-	clk32k_in: xtal1 {
+	clk32k_in: clock-xtal1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
@@ -1030,16 +1054,13 @@
 		nvidia,audio-codec = <&sgtl5000>;
 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA30_CLK_EXTERN1>;
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
-	};
-};
 
-&gpio {
-	lan-reset-n {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET#";
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra30-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp-microvolt.dtsi
new file mode 100644
index 000000000000..b8e0e9117021
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp-microvolt.dtsi
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	cpu0_opp_table: opp-table-cpu0 {
+		opp-51000000-800 {
+			opp-microvolt = <800000 800000 1250000>;
+		};
+
+		opp-51000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-51000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-102000000-800 {
+			opp-microvolt = <800000 800000 1250000>;
+		};
+
+		opp-102000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-102000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-204000000-800 {
+			opp-microvolt = <800000 800000 1250000>;
+		};
+
+		opp-204000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-204000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-312000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-312000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-340000000-800 {
+			opp-microvolt = <800000 800000 1250000>;
+		};
+
+		opp-340000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-370000000-800 {
+			opp-microvolt = <800000 800000 1250000>;
+		};
+
+		opp-456000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-456000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-475000000-800 {
+			opp-microvolt = <800000 800000 1250000>;
+		};
+
+		opp-475000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-608000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-608000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-620000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-640000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-640000000-900 {
+			opp-microvolt = <900000 900000 1250000>;
+		};
+
+		opp-760000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-760000000-900 {
+			opp-microvolt = <900000 900000 1250000>;
+		};
+
+		opp-760000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-760000000-975 {
+			opp-microvolt = <975000 975000 1250000>;
+		};
+
+		opp-816000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-816000000-912 {
+			opp-microvolt = <912000 912000 1250000>;
+		};
+
+		opp-860000000-850 {
+			opp-microvolt = <850000 850000 1250000>;
+		};
+
+		opp-860000000-900 {
+			opp-microvolt = <900000 900000 1250000>;
+		};
+
+		opp-860000000-975 {
+			opp-microvolt = <975000 975000 1250000>;
+		};
+
+		opp-860000000-1000 {
+			opp-microvolt = <1000000 1000000 1250000>;
+		};
+
+		opp-910000000-900 {
+			opp-microvolt = <900000 900000 1250000>;
+		};
+
+		opp-1000000000-900 {
+			opp-microvolt = <900000 900000 1250000>;
+		};
+
+		opp-1000000000-975 {
+			opp-microvolt = <975000 975000 1250000>;
+		};
+
+		opp-1000000000-1000 {
+			opp-microvolt = <1000000 1000000 1250000>;
+		};
+
+		opp-1000000000-1025 {
+			opp-microvolt = <1025000 1025000 1250000>;
+		};
+
+		opp-1100000000-900 {
+			opp-microvolt = <900000 900000 1250000>;
+		};
+
+		opp-1100000000-975 {
+			opp-microvolt = <975000 975000 1250000>;
+		};
+
+		opp-1100000000-1000 {
+			opp-microvolt = <1000000 1000000 1250000>;
+		};
+
+		opp-1100000000-1025 {
+			opp-microvolt = <1025000 1025000 1250000>;
+		};
+
+		opp-1100000000-1075 {
+			opp-microvolt = <1075000 1075000 1250000>;
+		};
+
+		opp-1150000000-975 {
+			opp-microvolt = <975000 975000 1250000>;
+		};
+
+		opp-1200000000-975 {
+			opp-microvolt = <975000 975000 1250000>;
+		};
+
+		opp-1200000000-1000 {
+			opp-microvolt = <1000000 1000000 1250000>;
+		};
+
+		opp-1200000000-1025 {
+			opp-microvolt = <1025000 1025000 1250000>;
+		};
+
+		opp-1200000000-1050 {
+			opp-microvolt = <1050000 1050000 1250000>;
+		};
+
+		opp-1200000000-1075 {
+			opp-microvolt = <1075000 1075000 1250000>;
+		};
+
+		opp-1200000000-1100 {
+			opp-microvolt = <1100000 1100000 1250000>;
+		};
+
+		opp-1300000000-1000 {
+			opp-microvolt = <1000000 1000000 1250000>;
+		};
+
+		opp-1300000000-1025 {
+			opp-microvolt = <1025000 1025000 1250000>;
+		};
+
+		opp-1300000000-1050 {
+			opp-microvolt = <1050000 1050000 1250000>;
+		};
+
+		opp-1300000000-1075 {
+			opp-microvolt = <1075000 1075000 1250000>;
+		};
+
+		opp-1300000000-1100 {
+			opp-microvolt = <1100000 1100000 1250000>;
+		};
+
+		opp-1300000000-1125 {
+			opp-microvolt = <1125000 1125000 1250000>;
+		};
+
+		opp-1300000000-1150 {
+			opp-microvolt = <1150000 1150000 1250000>;
+		};
+
+		opp-1300000000-1175 {
+			opp-microvolt = <1175000 1175000 1250000>;
+		};
+
+		opp-1400000000-1100 {
+			opp-microvolt = <1100000 1100000 1250000>;
+		};
+
+		opp-1400000000-1125 {
+			opp-microvolt = <1125000 1125000 1250000>;
+		};
+
+		opp-1400000000-1150 {
+			opp-microvolt = <1150000 1150000 1250000>;
+		};
+
+		opp-1400000000-1175 {
+			opp-microvolt = <1175000 1175000 1250000>;
+		};
+
+		opp-1400000000-1237 {
+			opp-microvolt = <1237000 1237000 1250000>;
+		};
+
+		opp-1500000000-1125 {
+			opp-microvolt = <1125000 1125000 1250000>;
+		};
+
+		opp-1500000000-1150 {
+			opp-microvolt = <1150000 1150000 1250000>;
+		};
+
+		opp-1500000000-1200 {
+			opp-microvolt = <1200000 1200000 1250000>;
+		};
+
+		opp-1500000000-1237 {
+			opp-microvolt = <1237000 1237000 1250000>;
+		};
+
+		opp-1600000000-1212 {
+			opp-microvolt = <1212000 1212000 1250000>;
+		};
+
+		opp-1600000000-1237 {
+			opp-microvolt = <1237000 1237000 1250000>;
+		};
+
+		opp-1700000000-1212 {
+			opp-microvolt = <1212000 1212000 1250000>;
+		};
+
+		opp-1700000000-1237 {
+			opp-microvolt = <1237000 1237000 1250000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-cpu-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp.dtsi
new file mode 100644
index 000000000000..5b9ebb75a09f
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp.dtsi
@@ -0,0 +1,499 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	cpu0_opp_table: opp-table-cpu0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-51000000-800 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x31FE>;
+			opp-hz = /bits/ 64 <51000000>;
+		};
+
+		opp-51000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0C01>;
+			opp-hz = /bits/ 64 <51000000>;
+		};
+
+		opp-51000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <51000000>;
+		};
+
+		opp-102000000-800 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x31FE>;
+			opp-hz = /bits/ 64 <102000000>;
+		};
+
+		opp-102000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0C01>;
+			opp-hz = /bits/ 64 <102000000>;
+		};
+
+		opp-102000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <102000000>;
+		};
+
+		opp-204000000-800 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x31FE>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-suspend;
+		};
+
+		opp-204000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0C01>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-suspend;
+		};
+
+		opp-204000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-suspend;
+		};
+
+		opp-312000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0C00>;
+			opp-hz = /bits/ 64 <312000000>;
+		};
+
+		opp-312000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <312000000>;
+		};
+
+		opp-340000000-800 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0192>;
+			opp-hz = /bits/ 64 <340000000>;
+		};
+
+		opp-340000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x0F 0x0001>;
+			opp-hz = /bits/ 64 <340000000>;
+		};
+
+		opp-370000000-800 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1E 0x306C>;
+			opp-hz = /bits/ 64 <370000000>;
+		};
+
+		opp-456000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0C00>;
+			opp-hz = /bits/ 64 <456000000>;
+		};
+
+		opp-456000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <456000000>;
+		};
+
+		opp-475000000-800 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1E 0x31FE>;
+			opp-hz = /bits/ 64 <475000000>;
+		};
+
+		opp-475000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x0F 0x0001>, <0x01 0x0002>,
+					   <0x01 0x0010>, <0x01 0x0080>,
+					   <0x01 0x0100>;
+			opp-hz = /bits/ 64 <475000000>;
+		};
+
+		opp-608000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0400>;
+			opp-hz = /bits/ 64 <608000000>;
+		};
+
+		opp-608000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <608000000>;
+		};
+
+		opp-620000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1E 0x306C>;
+			opp-hz = /bits/ 64 <620000000>;
+		};
+
+		opp-640000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x0F 0x0001>, <0x02 0x0002>,
+					   <0x04 0x0002>, <0x08 0x0002>,
+					   <0x02 0x0010>, <0x04 0x0010>,
+					   <0x08 0x0010>, <0x02 0x0080>,
+					   <0x04 0x0080>, <0x08 0x0080>,
+					   <0x10 0x0080>, <0x02 0x0100>,
+					   <0x04 0x0100>, <0x08 0x0100>,
+					   <0x10 0x0100>;
+			opp-hz = /bits/ 64 <640000000>;
+		};
+
+		opp-640000000-900 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0192>;
+			opp-hz = /bits/ 64 <640000000>;
+		};
+
+		opp-760000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1E 0x3461>, <0x08 0x0002>,
+					   <0x08 0x0004>, <0x08 0x0008>,
+					   <0x08 0x0010>, <0x08 0x0080>,
+					   <0x10 0x0080>, <0x08 0x0100>,
+					   <0x10 0x0100>, <0x01 0x0400>;
+			opp-hz = /bits/ 64 <760000000>;
+		};
+
+		opp-760000000-900 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0001>, <0x02 0x0002>,
+					   <0x04 0x0002>, <0x02 0x0004>,
+					   <0x04 0x0004>, <0x02 0x0008>,
+					   <0x04 0x0008>, <0x02 0x0010>,
+					   <0x04 0x0010>, <0x02 0x0080>,
+					   <0x04 0x0080>, <0x02 0x0100>,
+					   <0x04 0x0100>;
+			opp-hz = /bits/ 64 <760000000>;
+		};
+
+		opp-760000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <760000000>;
+		};
+
+		opp-760000000-975 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0192>;
+			opp-hz = /bits/ 64 <760000000>;
+		};
+
+		opp-816000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0400>;
+			opp-hz = /bits/ 64 <816000000>;
+		};
+
+		opp-816000000-912 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x1F 0x0200>;
+			opp-hz = /bits/ 64 <816000000>;
+		};
+
+		opp-860000000-850 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x0C 0x0001>;
+			opp-hz = /bits/ 64 <860000000>;
+		};
+
+		opp-860000000-900 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x0001>, <0x04 0x0002>,
+					   <0x08 0x0002>, <0x04 0x0004>,
+					   <0x08 0x0004>, <0x04 0x0008>,
+					   <0x08 0x0008>, <0x04 0x0010>,
+					   <0x08 0x0010>, <0x04 0x0080>,
+					   <0x08 0x0080>, <0x10 0x0080>,
+					   <0x04 0x0100>, <0x08 0x0100>,
+					   <0x10 0x0100>;
+			opp-hz = /bits/ 64 <860000000>;
+		};
+
+		opp-860000000-975 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0001>, <0x02 0x0002>,
+					   <0x02 0x0004>, <0x02 0x0008>,
+					   <0x02 0x0010>, <0x02 0x0080>,
+					   <0x02 0x0100>;
+			opp-hz = /bits/ 64 <860000000>;
+		};
+
+		opp-860000000-1000 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0192>;
+			opp-hz = /bits/ 64 <860000000>;
+		};
+
+		opp-910000000-900 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x18 0x3060>;
+			opp-hz = /bits/ 64 <910000000>;
+		};
+
+		opp-1000000000-900 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x0C 0x0001>;
+			opp-hz = /bits/ 64 <1000000000>;
+		};
+
+		opp-1000000000-975 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x03 0x0001>, <0x04 0x0002>,
+					   <0x08 0x0002>, <0x04 0x0004>,
+					   <0x08 0x0004>, <0x04 0x0008>,
+					   <0x08 0x0008>, <0x04 0x0010>,
+					   <0x08 0x0010>, <0x04 0x0080>,
+					   <0x08 0x0080>, <0x10 0x0080>,
+					   <0x04 0x0100>, <0x08 0x0100>,
+					   <0x10 0x0100>;
+			opp-hz = /bits/ 64 <1000000000>;
+		};
+
+		opp-1000000000-1000 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x019E>;
+			opp-hz = /bits/ 64 <1000000000>;
+		};
+
+		opp-1000000000-1025 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0192>;
+			opp-hz = /bits/ 64 <1000000000>;
+		};
+
+		opp-1100000000-900 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x08 0x0001>;
+			opp-hz = /bits/ 64 <1100000000>;
+		};
+
+		opp-1100000000-975 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x06 0x0001>, <0x08 0x0002>,
+					   <0x08 0x0004>, <0x08 0x0008>,
+					   <0x08 0x0010>, <0x08 0x0080>,
+					   <0x10 0x0080>, <0x08 0x0100>,
+					   <0x10 0x0100>;
+			opp-hz = /bits/ 64 <1100000000>;
+		};
+
+		opp-1100000000-1000 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0001>, <0x04 0x0002>,
+					   <0x04 0x0004>, <0x04 0x0008>,
+					   <0x04 0x0010>, <0x04 0x0080>,
+					   <0x04 0x0100>;
+			opp-hz = /bits/ 64 <1100000000>;
+		};
+
+		opp-1100000000-1025 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x019E>;
+			opp-hz = /bits/ 64 <1100000000>;
+		};
+
+		opp-1100000000-1075 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0192>;
+			opp-hz = /bits/ 64 <1100000000>;
+		};
+
+		opp-1150000000-975 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x18 0x3060>;
+			opp-hz = /bits/ 64 <1150000000>;
+		};
+
+		opp-1200000000-975 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x08 0x0001>;
+			opp-hz = /bits/ 64 <1200000000>;
+		};
+
+		opp-1200000000-1000 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x04 0x0001>, <0x08 0x0002>,
+					   <0x08 0x0004>, <0x08 0x0008>,
+					   <0x08 0x0010>, <0x08 0x0080>,
+					   <0x10 0x0080>, <0x08 0x0100>,
+					   <0x10 0x0100>;
+			opp-hz = /bits/ 64 <1200000000>;
+		};
+
+		opp-1200000000-1025 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x0001>, <0x04 0x0002>,
+					   <0x04 0x0004>, <0x04 0x0008>,
+					   <0x04 0x0010>, <0x04 0x0080>,
+					   <0x04 0x0100>;
+			opp-hz = /bits/ 64 <1200000000>;
+		};
+
+		opp-1200000000-1050 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x019E>;
+			opp-hz = /bits/ 64 <1200000000>;
+		};
+
+		opp-1200000000-1075 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0001>;
+			opp-hz = /bits/ 64 <1200000000>;
+		};
+
+		opp-1200000000-1100 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0192>;
+			opp-hz = /bits/ 64 <1200000000>;
+		};
+
+		opp-1300000000-1000 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x08 0x0001>, <0x10 0x0080>,
+					   <0x10 0x0100>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1025 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x04 0x0001>, <0x08 0x0002>,
+					   <0x08 0x0080>, <0x08 0x0100>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1050 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x12 0x3061>, <0x04 0x0002>,
+					   <0x08 0x0004>, <0x08 0x0008>,
+					   <0x08 0x0010>, <0x08 0x0020>,
+					   <0x08 0x0040>, <0x04 0x0080>,
+					   <0x04 0x0100>, <0x08 0x1000>,
+					   <0x08 0x2000>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1075 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x0182>, <0x04 0x0004>,
+					   <0x04 0x0008>, <0x04 0x0010>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1100 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x001C>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1125 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0001>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1150 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0182>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1300000000-1175 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0010>;
+			opp-hz = /bits/ 64 <1300000000>;
+		};
+
+		opp-1400000000-1100 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x18 0x307C>;
+			opp-hz = /bits/ 64 <1400000000>;
+		};
+
+		opp-1400000000-1125 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x04 0x000C>;
+			opp-hz = /bits/ 64 <1400000000>;
+		};
+
+		opp-1400000000-1150 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x000C>, <0x04 0x0010>;
+			opp-hz = /bits/ 64 <1400000000>;
+		};
+
+		opp-1400000000-1175 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x0010>;
+			opp-hz = /bits/ 64 <1400000000>;
+		};
+
+		opp-1400000000-1237 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0010>;
+			opp-hz = /bits/ 64 <1400000000>;
+		};
+
+		opp-1500000000-1125 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x08 0x0010>, <0x10 0x0020>,
+					   <0x10 0x0040>, <0x10 0x1000>,
+					   <0x10 0x2000>;
+			opp-hz = /bits/ 64 <1500000000>;
+		};
+
+		opp-1500000000-1150 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x04 0x0010>, <0x08 0x0020>,
+					   <0x08 0x0040>, <0x08 0x1000>,
+					   <0x08 0x2000>;
+			opp-hz = /bits/ 64 <1500000000>;
+		};
+
+		opp-1500000000-1200 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x02 0x0010>;
+			opp-hz = /bits/ 64 <1500000000>;
+		};
+
+		opp-1500000000-1237 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x01 0x0010>;
+			opp-hz = /bits/ 64 <1500000000>;
+		};
+
+		opp-1600000000-1212 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x10 0x3060>;
+			opp-hz = /bits/ 64 <1600000000>;
+		};
+
+		opp-1600000000-1237 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x08 0x3060>;
+			opp-hz = /bits/ 64 <1600000000>;
+		};
+
+		opp-1700000000-1212 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x10 0x3060>;
+			opp-hz = /bits/ 64 <1700000000>;
+		};
+
+		opp-1700000000-1237 {
+			clock-latency-ns = <100000>;
+			opp-supported-hw = <0x08 0x3060>;
+			opp-hz = /bits/ 64 <1700000000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-ouya.dts b/arch/arm/boot/dts/nvidia/tegra30-ouya.dts
new file mode 100644
index 000000000000..7e3de26ca960
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-ouya.dts
@@ -0,0 +1,4798 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+
+/ {
+	model = "Ouya Game Console";
+	compatible = "ouya,ouya", "nvidia,tegra30";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc3; /* WiFi */
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+		serial0 = &uartd; /* Debug Port */
+		serial1 = &uartc; /* Bluetooth */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <0x0>;
+			tlm,version-minor = <0x0>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@bfdf0000 {
+			compatible = "ramoops";
+			reg = <0xbfdf0000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi@54280000 {
+			status = "okay";
+			vdd-supply = <&vdd_vid_reg>;
+			pll-supply = <&ldo7_reg>;
+			hdmi-supply = <&sys_3v3_reg>;
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			clk_32k_out_pa0 {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart3_cts_n_pa1 {
+				nvidia,pins = "uart3_cts_n_pa1";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_fs_pa2 {
+				nvidia,pins = "dap2_fs_pa2";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_sclk_pa3 {
+				nvidia,pins = "dap2_sclk_pa3";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_din_pa4 {
+				nvidia,pins = "dap2_din_pa4";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_dout_pa5 {
+				nvidia,pins = "dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_a18_pb1 {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pclk_pb3 {
+				nvidia,pins = "lcd_pclk_pb3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat3_pb4 {
+				nvidia,pins = "sdmmc3_dat3_pb4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat2_pb5 {
+				nvidia,pins = "sdmmc3_dat2_pb5";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat1_pb6 {
+				nvidia,pins = "sdmmc3_dat1_pb6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat0_pb7 {
+				nvidia,pins = "sdmmc3_dat0_pb7";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uart3_rts_n_pc0 {
+				nvidia,pins = "uart3_rts_n_pc0";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pwr1_pc1 {
+				nvidia,pins = "lcd_pwr1_pc1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_txd_pc2 {
+				nvidia,pins = "uart2_txd_pc2";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_rxd_pc3 {
+				nvidia,pins = "uart2_rxd_pc3";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen1_i2c_scl_pc4 {
+				nvidia,pins = "gen1_i2c_scl_pc4";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen1_i2c_sda_pc5 {
+				nvidia,pins = "gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat5_pd0 {
+				nvidia,pins = "sdmmc3_dat5_pd0";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat4_pd1 {
+				nvidia,pins = "sdmmc3_dat4_pd1";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_dc1_pd2 {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat6_pd3 {
+				nvidia,pins = "sdmmc3_dat6_pd3";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat7_pd4 {
+				nvidia,pins = "sdmmc3_dat7_pd4";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d1_pd5 {
+				nvidia,pins = "vi_d1_pd5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_vsync_pd6 {
+				nvidia,pins = "vi_vsync_pd6";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_hsync_pd7 {
+				nvidia,pins = "vi_hsync_pd7";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_d0_pe0 {
+				nvidia,pins = "lcd_d0_pe0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d1_pe1 {
+				nvidia,pins = "lcd_d1_pe1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d2_pe2 {
+				nvidia,pins = "lcd_d2_pe2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d3_pe3 {
+				nvidia,pins = "lcd_d3_pe3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d4_pe4 {
+				nvidia,pins = "lcd_d4_pe4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d5_pe5 {
+				nvidia,pins = "lcd_d5_pe5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d6_pe6 {
+				nvidia,pins = "lcd_d6_pe6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d7_pe7 {
+				nvidia,pins = "lcd_d7_pe7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d8_pf0 {
+				nvidia,pins = "lcd_d8_pf0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d9_pf1 {
+				nvidia,pins = "lcd_d9_pf1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d10_pf2 {
+				nvidia,pins = "lcd_d10_pf2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d11_pf3 {
+				nvidia,pins = "lcd_d11_pf3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d12_pf4 {
+				nvidia,pins = "lcd_d12_pf4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d13_pf5 {
+				nvidia,pins = "lcd_d13_pf5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d14_pf6 {
+				nvidia,pins = "lcd_d14_pf6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d15_pf7 {
+				nvidia,pins = "lcd_d15_pf7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad1_pg1 {
+				nvidia,pins = "gmi_ad1_pg1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad2_pg2 {
+				nvidia,pins = "gmi_ad2_pg2";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad3_pg3 {
+				nvidia,pins = "gmi_ad3_pg3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad4_pg4 {
+				nvidia,pins = "gmi_ad4_pg4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad5_pg5 {
+				nvidia,pins = "gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad6_pg6 {
+				nvidia,pins = "gmi_ad6_pg6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad7_pg7 {
+				nvidia,pins = "gmi_ad7_pg7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad8_ph0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad11_ph3 {
+				nvidia,pins = "gmi_ad11_ph3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad12_ph4 {
+				nvidia,pins = "gmi_ad12_ph4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad14_ph6 {
+				nvidia,pins = "gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wr_n_pi0 {
+				nvidia,pins = "gmi_wr_n_pi0";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_oe_n_pi1 {
+				nvidia,pins = "gmi_oe_n_pi1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_dqs_pi2 {
+				nvidia,pins = "gmi_dqs_pi2";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_iordy_pi5 {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs7_n_pi6 {
+				nvidia,pins = "gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wait_pi7 {
+				nvidia,pins = "gmi_wait_pi7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_de_pj1 {
+				nvidia,pins = "lcd_de_pj1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs1_n_pj2 {
+				nvidia,pins = "gmi_cs1_n_pj2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_hsync_pj3 {
+				nvidia,pins = "lcd_hsync_pj3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_vsync_pj4 {
+				nvidia,pins = "lcd_vsync_pj4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_cts_n_pj5 {
+				nvidia,pins = "uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_rts_n_pj6 {
+				nvidia,pins = "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_a16_pj7 {
+				nvidia,pins = "gmi_a16_pj7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_adv_n_pk0 {
+				nvidia,pins = "gmi_adv_n_pk0";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_clk_pk1 {
+				nvidia,pins = "gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs2_n_pk3 {
+				nvidia,pins = "gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs3_n_pk4 {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_out_pk5 {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_in_pk6 {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a19_pk7 {
+				nvidia,pins = "gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d2_pl0 {
+				nvidia,pins = "vi_d2_pl0";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d3_pl1 {
+				nvidia,pins = "vi_d3_pl1";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d4_pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d5_pl3 {
+				nvidia,pins = "vi_d5_pl3";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d6_pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d7_pl5 {
+				nvidia,pins = "vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d8_pl6 {
+				nvidia,pins = "vi_d8_pl6";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d9_pl7 {
+				nvidia,pins = "vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d16_pm0 {
+				nvidia,pins = "lcd_d16_pm0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d17_pm1 {
+				nvidia,pins = "lcd_d17_pm1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d18_pm2 {
+				nvidia,pins = "lcd_d18_pm2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d19_pm3 {
+				nvidia,pins = "lcd_d19_pm3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d20_pm4 {
+				nvidia,pins = "lcd_d20_pm4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d21_pm5 {
+				nvidia,pins = "lcd_d21_pm5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d22_pm6 {
+				nvidia,pins = "lcd_d22_pm6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d23_pm7 {
+				nvidia,pins = "lcd_d23_pm7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_dout_pn2 {
+				nvidia,pins = "dap1_dout_pn2";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_sclk_pn3 {
+				nvidia,pins = "dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_cs0_n_pn4 {
+				nvidia,pins = "lcd_cs0_n_pn4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_sdout_pn5 {
+				nvidia,pins = "lcd_sdout_pn5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_dc0_pn6 {
+				nvidia,pins = "lcd_dc0_pn6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			hdmi_int_pn7 {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data0_po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data1_po2 {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data2_po3 {
+				nvidia,pins = "ulpi_data2_po3";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data3_po4 {
+				nvidia,pins = "ulpi_data3_po4";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data4_po5 {
+				nvidia,pins = "ulpi_data4_po5";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data5_po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data6_po7 {
+				nvidia,pins = "ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap3_fs_pp0 {
+				nvidia,pins = "dap3_fs_pp0";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_dout_pp2 {
+				nvidia,pins = "dap3_dout_pp2";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_sclk_pp3 {
+				nvidia,pins = "dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_fs_pp4 {
+				nvidia,pins = "dap4_fs_pp4";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_din_pp5 {
+				nvidia,pins = "dap4_din_pp5";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_dout_pp6 {
+				nvidia,pins = "dap4_dout_pp6";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_sclk_pp7 {
+				nvidia,pins = "dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_col0_pq0 {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col1_pq1 {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col2_pq2 {
+				nvidia,pins = "kb_col2_pq2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col3_pq3 {
+				nvidia,pins = "kb_col3_pq3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col4_pq4 {
+				nvidia,pins = "kb_col4_pq4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col5_pq5 {
+				nvidia,pins = "kb_col5_pq5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col6_pq6 {
+				nvidia,pins = "kb_col6_pq6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col7_pq7 {
+				nvidia,pins = "kb_col7_pq7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row1_pr1 {
+				nvidia,pins = "kb_row1_pr1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row2_pr2 {
+				nvidia,pins = "kb_row2_pr2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row4_pr4 {
+				nvidia,pins = "kb_row4_pr4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row5_pr5 {
+				nvidia,pins = "kb_row5_pr5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row6_pr6 {
+				nvidia,pins = "kb_row6_pr6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row8_ps0 {
+				nvidia,pins = "kb_row8_ps0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row9_ps1 {
+				nvidia,pins = "kb_row9_ps1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row10_ps2 {
+				nvidia,pins = "kb_row10_ps2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row11_ps3 {
+				nvidia,pins = "kb_row11_ps3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row12_ps4 {
+				nvidia,pins = "kb_row12_ps4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row13_ps5 {
+				nvidia,pins = "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row14_ps6 {
+				nvidia,pins = "kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row15_ps7 {
+				nvidia,pins = "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_pclk_pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_mclk_pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d10_pt2 {
+				nvidia,pins = "vi_d10_pt2";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d11_pt3 {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d0_pt4 {
+				nvidia,pins = "vi_d0_pt4";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gen2_i2c_scl_pt5 {
+				nvidia,pins = "gen2_i2c_scl_pt5";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen2_i2c_sda_pt6 {
+				nvidia,pins = "gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_cmd_pt7 {
+				nvidia,pins = "sdmmc4_cmd_pt7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu0 {
+				nvidia,pins = "pu0";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu1 {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu6 {
+				nvidia,pins = "pu6";
+				nvidia,function = "pwm3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag_rtck_pu7 {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv0 {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv1 {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv2 {
+				nvidia,pins = "pv2";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "clk_12m_out";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ddc_scl_pv4 {
+				nvidia,pins = "ddc_scl_pv4";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ddc_sda_pv5 {
+				nvidia,pins = "ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_vsync_pv7 {
+				nvidia,pins = "crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_cs1_n_pw0 {
+				nvidia,pins = "lcd_cs1_n_pw0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_m1_pw1 {
+				nvidia,pins = "lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_cs1_n_pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1_out_pw4 {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_out_pw5 {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uart3_txd_pw6 {
+				nvidia,pins = "uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart3_rxd_pw7 {
+				nvidia,pins = "uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_sck_px2 {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_cs0_n_px6 {
+				nvidia,pins = "spi1_cs0_n_px6";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_dir_py1 {
+				nvidia,pins = "ulpi_dir_py1";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_stp_py3 {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat3_py4 {
+				nvidia,pins = "sdmmc1_dat3_py4";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat2_py5 {
+				nvidia,pins = "sdmmc1_dat2_py5";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat1_py6 {
+				nvidia,pins = "sdmmc1_dat1_py6";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat0_py7 {
+				nvidia,pins = "sdmmc1_dat0_py7";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_clk_pz0 {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_cmd_pz1 {
+				nvidia,pins = "sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_sdin_pz2 {
+				nvidia,pins = "lcd_sdin_pz2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_wr_n_pz3 {
+				nvidia,pins = "lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_sck_pz4 {
+				nvidia,pins = "lcd_sck_pz4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sys_clk_req_pz5 {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwr_i2c_scl_pz6 {
+				nvidia,pins = "pwr_i2c_scl_pz6";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+
+			pwr_i2c_sda_pz7 {
+				nvidia,pins = "pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_dat0_paa0 {
+				nvidia,pins = "sdmmc4_dat0_paa0";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat1_paa1 {
+				nvidia,pins = "sdmmc4_dat1_paa1";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat2_paa2 {
+				nvidia,pins = "sdmmc4_dat2_paa2";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat3_paa3 {
+				nvidia,pins = "sdmmc4_dat3_paa3";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat4_paa4 {
+				nvidia,pins = "sdmmc4_dat4_paa4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat5_paa5 {
+				nvidia,pins = "sdmmc4_dat5_paa5";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat6_paa6 {
+				nvidia,pins = "sdmmc4_dat6_paa6";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat7_paa7 {
+				nvidia,pins = "sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb0 {
+				nvidia,pins = "pbb0";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam_i2c_scl_pbb1 {
+				nvidia,pins = "cam_i2c_scl_pbb1";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam_i2c_sda_pbb2 {
+				nvidia,pins = "cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam_mclk_pcc0 {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc2 {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_rst_n_pcc3 {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_rst_n_pcc6 {
+				nvidia,pins = "pex_l2_rst_n_pcc6";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_clkreq_n_pcc7 {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l0_prsnt_n_pdd0 {
+				nvidia,pins = "pex_l0_prsnt_n_pdd0";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l0_rst_n_pdd1 {
+				nvidia,pins = "pex_l0_rst_n_pdd1";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l0_clkreq_n_pdd2 {
+				nvidia,pins = "pex_l0_clkreq_n_pdd2";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_wake_n_pdd3 {
+				nvidia,pins = "pex_wake_n_pdd3";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l1_prsnt_n_pdd4 {
+				nvidia,pins = "pex_l1_prsnt_n_pdd4";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l1_rst_n_pdd5 {
+				nvidia,pins = "pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l1_clkreq_n_pdd6 {
+				nvidia,pins = "pex_l1_clkreq_n_pdd6";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_prsnt_n_pdd7 {
+				nvidia,pins = "pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			hdmi_cec_pee3 {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			drive_groups {
+				nvidia,pins = "drive_gma",
+					      "drive_gmb",
+					      "drive_gmc",
+					      "drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+		};
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		/* Azurewave AW-NH660 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			vbat-supply  = <&sys_3v3_reg>;
+			vddio-supply = <&vdd_1v8>;
+
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	uartd: serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+		status = "okay";
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 1 1 1 1 1 0 0 1>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_reg>;
+			vcc2-supply = <&vdd_5v0_reg>;
+			vcc3-supply = <&vdd_1v8>;
+			vcc4-supply = <&vdd_5v0_reg>;
+			vcc5-supply = <&vdd_5v0_reg>;
+			vcc6-supply = <&vdd2_reg>;
+			vcc7-supply = <&vdd_5v0_reg>;
+			vccio-supply = <&vdd_5v0_reg>;
+
+			regulators {
+				vdd1_reg: vdd1 {
+					regulator-name = "vddio_ddr_1v2";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				vdd2_reg: vdd2 {
+					regulator-name = "vdd_1v5_gen";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1270000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8: vio {
+					regulator-name = "vdd_1v8_gen";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo1_reg: ldo1 {
+					regulator-name = "vdd_pexa,vdd_pexb";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-always-on;
+				};
+
+				ldo2_reg: ldo2 {
+					regulator-name = "vdd_sata,avdd_plle";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-always-on;
+				};
+
+				/* LDO3 is not connected to anything */
+
+				ldo4_reg: ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo5_reg: ldo5 {
+					regulator-name = "vddio_sdmmc,avdd_vdac";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo6_reg: ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo7_reg: ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo8_reg: ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+			};
+		};
+
+		cpu_temp: nct1008@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+			vcc-supply = <&sys_3v3_reg>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
+		};
+
+		vdd_core: tps62361@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <950000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+			ti,enable-vout-discharge;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <1>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <458>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			nvidia,ram-code = <0>; /* Samsung RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emem-configuration = <
+					0x00030003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75830303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emem-configuration = <
+					0x00010003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74630303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emem-configuration = <
+					0x00000006 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emem-configuration = <
+					0x0000000c /* MC_EMEM_ARB_CFG */
+					0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7086120a /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emem-configuration = <
+					0x00000018 /* MC_EMEM_ARB_CFG */
+					0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x712c2414 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>; /* Hynix M RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emem-configuration = <
+					0x00030003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75830303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emem-configuration = <
+					0x00010003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74630303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emem-configuration = <
+					0x00000006 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emem-configuration = <
+					0x0000000c /* MC_EMEM_ARB_CFG */
+					0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7086120a /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emem-configuration = <
+					0x00000018 /* MC_EMEM_ARB_CFG */
+					0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x712c2414 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-2 {
+			nvidia,ram-code = <2>; /* Hynix A RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emem-configuration = <
+					0x00030003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75e30303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emem-configuration = <
+					0x00010003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74e30303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x74430504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emem-configuration = <
+					0x00000006 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x74040a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emem-configuration = <
+					0x0000000c /* MC_EMEM_ARB_CFG */
+					0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7086120a /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emem-configuration = <
+					0x00000018 /* MC_EMEM_ARB_CFG */
+					0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x712c2414 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			nvidia,ram-code = <0>;  /* Samsung RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000006 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000007 /* EMC_TXSR */
+					0x00000007 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x0000000d /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000000e /* EMC_TXSR */
+					0x0000000e /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000003 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000004 /* EMC_RC */
+					0x0000001a /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000001c /* EMC_TXSR */
+					0x0000001c /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000009 /* EMC_RC */
+					0x00000035 /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000038 /* EMC_TXSR */
+					0x00000038 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000009 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-configuration = <
+					0x00000012 /* EMC_RC */
+					0x00000066 /* EMC_RFC */
+					0x0000000c /* EMC_RAS */
+					0x00000004 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x0000000a /* EMC_W2P */
+					0x00000004 /* EMC_RD_RCD */
+					0x00000004 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x00000bf0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000008 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000006c /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000010 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000c30 /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x001d0084 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS4 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS5 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS6 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0158000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-configuration = <
+					0x00000025 /* EMC_RC */
+					0x000000ce /* EMC_RFC */
+					0x0000001a /* EMC_RAS */
+					0x00000009 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000d /* EMC_W2R */
+					0x00000004 /* EMC_R2P */
+					0x00000013 /* EMC_W2P */
+					0x00000009 /* EMC_RD_RCD */
+					0x00000009 /* EMC_WR_RCD */
+					0x00000004 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001820 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000003 /* EMC_PDEX2WR */
+					0x00000012 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000f /* EMC_AR2PDEN */
+					0x00000018 /* EMC_RW2PDEN */
+					0x000000d8 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000020 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000007 /* EMC_TCLKSTABLE */
+					0x00000008 /* EMC_TCLKSTOP */
+					0x00001860 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf0070191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000800a /* EMC_DLL_XFORM_DQS0 */
+					0x0000000a /* EMC_DLL_XFORM_DQS1 */
+					0x0000000a /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000a /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x00f0000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>;  /* Hynix M RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000006 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000007 /* EMC_TXSR */
+					0x00000007 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x0000000d /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000000e /* EMC_TXSR */
+					0x0000000e /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000003 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000004 /* EMC_RC */
+					0x0000001a /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000001c /* EMC_TXSR */
+					0x0000001c /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000009 /* EMC_RC */
+					0x00000035 /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000038 /* EMC_TXSR */
+					0x00000038 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000009 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-configuration = <
+					0x00000012 /* EMC_RC */
+					0x00000066 /* EMC_RFC */
+					0x0000000c /* EMC_RAS */
+					0x00000004 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x0000000a /* EMC_W2P */
+					0x00000004 /* EMC_RD_RCD */
+					0x00000004 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x00000bf0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000008 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000006c /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000010 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000c30 /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x001d0084 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS4 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS5 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS6 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0158000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-configuration = <
+					0x00000025 /* EMC_RC */
+					0x000000ce /* EMC_RFC */
+					0x0000001a /* EMC_RAS */
+					0x00000009 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000d /* EMC_W2R */
+					0x00000004 /* EMC_R2P */
+					0x00000013 /* EMC_W2P */
+					0x00000009 /* EMC_RD_RCD */
+					0x00000009 /* EMC_WR_RCD */
+					0x00000004 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001820 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000003 /* EMC_PDEX2WR */
+					0x00000012 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000f /* EMC_AR2PDEN */
+					0x00000018 /* EMC_RW2PDEN */
+					0x000000d8 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000020 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000007 /* EMC_TCLKSTABLE */
+					0x00000008 /* EMC_TCLKSTOP */
+					0x00001860 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf0070191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000800a /* EMC_DLL_XFORM_DQS0 */
+					0x0000000a /* EMC_DLL_XFORM_DQS1 */
+					0x0000000a /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000a /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x00f0000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+
+		emc-timings-2 {
+			nvidia,ram-code = <2>;  /* Hynix A RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000007 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000008 /* EMC_TXSR */
+					0x00000008 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x0000000f /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000010 /* EMC_TXSR */
+					0x00000010 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000003 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000004 /* EMC_RC */
+					0x0000001e /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000020 /* EMC_TXSR */
+					0x00000020 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000009 /* EMC_RC */
+					0x0000003d /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000040 /* EMC_TXSR */
+					0x00000040 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000009 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-configuration = <
+					0x00000012 /* EMC_RC */
+					0x00000076 /* EMC_RFC */
+					0x0000000c /* EMC_RAS */
+					0x00000004 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x0000000a /* EMC_W2P */
+					0x00000004 /* EMC_RD_RCD */
+					0x00000004 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x00000bf0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000008 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000007c /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000010 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000c30 /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x001d0084 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00044000 /* EMC_DLL_XFORM_DQS0 */
+					0x00044000 /* EMC_DLL_XFORM_DQS1 */
+					0x00044000 /* EMC_DLL_XFORM_DQS2 */
+					0x00044000 /* EMC_DLL_XFORM_DQS3 */
+					0x00044000 /* EMC_DLL_XFORM_DQS4 */
+					0x00044000 /* EMC_DLL_XFORM_DQS5 */
+					0x00044000 /* EMC_DLL_XFORM_DQS6 */
+					0x00044000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00058000 /* EMC_DLL_XFORM_DQ0 */
+					0x00058000 /* EMC_DLL_XFORM_DQ1 */
+					0x00058000 /* EMC_DLL_XFORM_DQ2 */
+					0x00058000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0148000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-configuration = <
+					0x00000025 /* EMC_RC */
+					0x000000ee /* EMC_RFC */
+					0x0000001a /* EMC_RAS */
+					0x00000009 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000d /* EMC_W2R */
+					0x00000004 /* EMC_R2P */
+					0x00000013 /* EMC_W2P */
+					0x00000009 /* EMC_RD_RCD */
+					0x00000009 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001820 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000003 /* EMC_PDEX2WR */
+					0x00000012 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000f /* EMC_AR2PDEN */
+					0x00000018 /* EMC_RW2PDEN */
+					0x000000f8 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000020 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000007 /* EMC_TCLKSTABLE */
+					0x00000008 /* EMC_TCLKSTOP */
+					0x00001860 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf0070191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000000c /* EMC_DLL_XFORM_DQS0 */
+					0x007fc00a /* EMC_DLL_XFORM_DQS1 */
+					0x00000008 /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000c /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x0a000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x00d0000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&wifi_pwrseq>;
+		vmmc-supply = <&sdmmc_3v3_reg>;
+		vqmmc-supply = <&vdd_1v8>;
+
+		/* Azurewave AW-NH660 BCM4330 */
+		brcmf: wifi@1 {
+			reg = <1>;
+			compatible = "brcm,bcm4329-fmac";
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+
+		keep-power-in-suspend;
+		bus-width = <8>;
+		non-removable;
+		vmmc-supply = <&sys_3v3_reg>;
+		vqmmc-supply = <&vdd_1v8>;
+		nvidia,default-tap = <0x0F>;
+		max-frequency = <25500000>;
+	};
+
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb@7d004000 {
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet@2 { /* SMSC 10/100T Ethernet Controller */
+			compatible = "usb424,9e00";
+			reg = <2>;
+			local-mac-address = [00 11 22 33 44 55];
+		};
+	};
+
+	usb-phy@7d004000 {
+		vbus-supply = <&vdd_smsc>;
+		status = "okay";
+	};
+
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		vbus-supply = <&usb3_vbus_reg>;
+		status = "okay";
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			operating-points-v2 = <&cpu0_opp_table>;
+			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			operating-points-v2 = <&cpu0_opp_table>;
+			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			operating-points-v2 = <&cpu0_opp_table>;
+			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			operating-points-v2 = <&cpu0_opp_table>;
+			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	fan: fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio TEGRA_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0    0
+				      4500 1>;
+		#cooling-cells = <2>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			debounce-interval = <10>;
+			linux,code = <KEY_POWER>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "power-led";
+			gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+			retain-state-suspended;
+		};
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-900000000-1350;
+	};
+
+	wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	vdd_12v_in: regulator-vdd-12v-in {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_12v_in";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	sdmmc_3v3_reg: regulator-sdmmc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "sdmmc_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+	};
+
+	vdd_fuse_3v3_reg: regulator-vdd-fuse-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_fuse_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(L, 6) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&sys_3v3_reg>;
+		regulator-always-on;
+	};
+
+	vdd_vid_reg: regulator-vdd-vid {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio_vid";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(T, 0) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vdd_5v0_reg>;
+		regulator-boot-on;
+	};
+
+	ddr_reg: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+		vin-supply = <&vdd_12v_in>;
+	};
+
+	sys_3v3_reg: regulator-sys-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "sys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_12v_in>;
+	};
+
+	vdd_5v0_reg: regulator-vdd-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_12v_in>;
+	};
+
+	vdd_smsc: regulator-vdd-smsc {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_smsc";
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	usb3_vbus_reg: regulator-usb3-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vdd_5v0_reg>;
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay = <5000>;
+			polling-delay-passive = <5000>;
+
+			thermal-sensors = <&cpu_temp 1>;
+
+			trips {
+				cpu_alert0: cpu-alert0 {
+					temperature = <50000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+				cpu_alert1: cpu-alert1 {
+					temperature = <70000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+				map1 {
+					trip = <&cpu_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-pegatron-chagall.dts b/arch/arm/boot/dts/nvidia/tegra30-pegatron-chagall.dts
new file mode 100644
index 000000000000..4012f9c799a8
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-pegatron-chagall.dts
@@ -0,0 +1,2860 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Pegatron Chagall";
+	compatible = "pegatron,chagall", "nvidia,tegra30";
+	chassis-type = "tablet";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* uSD slot */
+		mmc2 = &sdmmc3; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		display0 = &lcd;
+		display1 = &hdmi;
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@beb00000 {
+			compatible = "ramoops";
+			reg = <0xbeb00000 0x10000>; /* 64kB */
+			console-size = <0x8000>; /* 32kB */
+			record-size = <0x400>; /* 1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>; /* 2MB */
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi: hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&vdd_1v8_vio>;
+			vdd-supply = <&vdd_3v3_sys>;
+
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* SDMMC1 pinmux */
+			sdmmc1_clk_pz0 {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_dat3_py4 {
+				nvidia,pins = "sdmmc1_dat3_py4",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat0_py7",
+						"sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC2 pinmux */
+			vi_d1_pd5 {
+				nvidia,pins = "vi_d1_pd5",
+						"vi_d2_pl0",
+						"vi_d3_pl1",
+						"vi_d5_pl3",
+						"vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d8_pl6 {
+				nvidia,pins = "vi_d8_pl6",
+						"vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* SDMMC3 pinmux */
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat3_pb4",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat5_pd0",
+						"sdmmc3_dat4_pd1",
+						"sdmmc3_dat6_pd3",
+						"sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC4 pinmux */
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_cmd_pt7 {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2C pinmux */
+			gen1_i2c_scl_pc4 {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			gen2_i2c_scl_pt5 {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			cam_i2c_scl_pbb1 {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			ddc_scl_pv4 {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			pwr_i2c_scl_pz6 {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			/* HDMI-CEC pinmux */
+			hdmi_cec_pee3 {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			/* UART-A */
+			ulpi_data0_po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data1_po2 {
+				nvidia,pins = "ulpi_data1_po2",
+						"ulpi_data2_po3",
+						"ulpi_data3_po4",
+						"ulpi_data4_po5",
+						"ulpi_data5_po6",
+						"ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-B */
+			uart2_txd_pc2 {
+				nvidia,pins = "uart2_txd_pc2",
+						"uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_rxd_pc3 {
+				nvidia,pins = "uart2_rxd_pc3",
+						"uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-C */
+			uart3_cts_n_pa1 {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uart3_rts_n_pc0 {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-D */
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0",
+						"ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_dir_py1 {
+				nvidia,pins = "ulpi_dir_py1",
+						"ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2S pinmux */
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_din_pn1",
+						"dap1_dout_pn2",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_fs_pa2 {
+				nvidia,pins = "dap2_fs_pa2",
+						"dap2_sclk_pa3",
+						"dap2_din_pa4",
+						"dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_fs_pp0 {
+				nvidia,pins = "dap3_fs_pp0",
+						"dap3_din_pp1",
+						"dap3_dout_pp2",
+						"dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_fs_pp4 {
+				nvidia,pins = "dap4_fs_pp4",
+						"dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc2 {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PCI-e pinmux */
+			pex_l2_rst_n_pcc6 {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+						"pex_l0_rst_n_pdd1",
+						"pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_clkreq_n_pcc7 {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7",
+						"pex_l0_prsnt_n_pdd0",
+						"pex_l0_clkreq_n_pdd2",
+						"pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pex_wake_n_pdd3 {
+				nvidia,pins = "pex_wake_n_pdd3";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* SPI pinmux */
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4",
+						"spi1_sck_px5",
+						"spi1_cs0_n_px6",
+						"spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_cs1_n_pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2",
+						"spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_sck_px2 {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a16_pj7 {
+				nvidia,pins = "gmi_a16_pj7",
+						"gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+						"gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_out_pk5 {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_in_pk6 {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Display A pinmux */
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+						"lcd_pclk_pb3",
+						"lcd_pwr1_pc1",
+						"lcd_pwr2_pc6",
+						"lcd_d0_pe0",
+						"lcd_d1_pe1",
+						"lcd_d2_pe2",
+						"lcd_d3_pe3",
+						"lcd_d4_pe4",
+						"lcd_d5_pe5",
+						"lcd_d6_pe6",
+						"lcd_d7_pe7",
+						"lcd_d8_pf0",
+						"lcd_d9_pf1",
+						"lcd_d10_pf2",
+						"lcd_d11_pf3",
+						"lcd_d12_pf4",
+						"lcd_d13_pf5",
+						"lcd_d14_pf6",
+						"lcd_d15_pf7",
+						"lcd_de_pj1",
+						"lcd_hsync_pj3",
+						"lcd_vsync_pj4",
+						"lcd_d16_pm0",
+						"lcd_d17_pm1",
+						"lcd_d18_pm2",
+						"lcd_d19_pm3",
+						"lcd_d20_pm4",
+						"lcd_d21_pm5",
+						"lcd_d22_pm6",
+						"lcd_d23_pm7",
+						"lcd_cs0_n_pn4",
+						"lcd_sdout_pn5",
+						"lcd_dc0_pn6",
+						"lcd_sdin_pz2",
+						"lcd_wr_n_pz3",
+						"lcd_sck_pz4",
+						"lcd_cs1_n_pw0",
+						"lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_dc1_pd2 {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk_32k_out_pa0 {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC keys */
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0",
+						"kb_row1_pr1",
+						"kb_row2_pr2",
+						"kb_row3_pr3",
+						"kb_row8_ps0",
+						"kb_col0_pq0",
+						"kb_col1_pq1",
+						"kb_col2_pq2",
+						"kb_col3_pq3",
+						"kb_col4_pq4",
+						"kb_col5_pq5",
+						"kb_col7_pq7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row4_pr4 {
+				nvidia,pins = "kb_row4_pr4",
+						"kb_row7_pr7",
+						"kb_row10_ps2",
+						"kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row11_ps3 {
+				nvidia,pins = "kb_row11_ps3",
+						"kb_row12_ps4",
+						"kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row14_ps6 {
+				nvidia,pins = "kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_iordy_pi5 {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_pclk_pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			pu1 {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv0 {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv1 {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_rst_n_pcc3 {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_vsync_pd6 {
+				nvidia,pins = "vi_vsync_pd6",
+						"vi_hsync_pd7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			vi_d10_pt2 {
+				nvidia,pins = "vi_d10_pt2",
+						"vi_d0_pt4", "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d11_pt3 {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu0 {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu6 {
+				nvidia,pins = "pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pex_l1_prsnt_n_pdd4 {
+				nvidia,pins = "pex_l1_prsnt_n_pdd4",
+						"pex_l1_clkreq_n_pdd6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_wait_pi7 {
+				nvidia,pins = "gmi_wait_pi7",
+						"gmi_cs0_n_pj0",
+						"gmi_cs1_n_pj2",
+						"gmi_cs4_n_pk2";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+						"gmi_ad1_pg1",
+						"gmi_ad2_pg2",
+						"gmi_ad3_pg3",
+						"gmi_ad4_pg4",
+						"gmi_ad5_pg5",
+						"gmi_ad6_pg6",
+						"gmi_ad7_pg7",
+						"gmi_wr_n_pi0",
+						"gmi_oe_n_pi1",
+						"gmi_dqs_pi2",
+						"gmi_adv_n_pk0",
+						"gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs2_n_pk3 {
+				nvidia,pins = "gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs3_n_pk4 {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+						"gmi_ad11_ph3",
+						"gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5",
+						"gmi_ad12_ph4",
+						"gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_rst_n_pi4 {
+				nvidia,pins = "gmi_rst_n_pi4";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad8_ph0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs6_n_pi3 {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "sata";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d4_pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d6_pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			vi_mclk_pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI hot-plug-detect */
+			hdmi_int_pn7 {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag_rtck_pu7 {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6",
+						"crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1_out_pw4 {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_out_pw5 {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sys_clk_req_pz5 {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv2 {
+				nvidia,pins = "pv2",
+						"kb_row5_pr5";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			cam_mclk_pcc0 {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive_dap1 {
+				nvidia,pins = "drive_dap1",
+						"drive_dap2",
+						"drive_dbg",
+						"drive_at5",
+						"drive_gme",
+						"drive_ddc",
+						"drive_ao1",
+						"drive_uart3";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <5>;
+				nvidia,pull-up-strength = <5>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+
+			drive_sdio3 {
+				nvidia,pins = "drive_sdio3";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+
+			drive_gma {
+				nvidia,pins = "drive_gma",
+						"drive_gmb",
+						"drive_gmc",
+						"drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			drive_lcd2 {
+				nvidia,pins = "drive_lcd2";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_4>;
+				nvidia,pull-down-strength = <20>;
+				nvidia,pull-up-strength = <20>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+		};
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Broadcom GPS BCM47511 */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		/* Azurewave AW-AH663 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+
+			vbat-supply  = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	pwm: pwm@7000a000 {
+		status = "okay";
+	};
+
+	lcd_ddc: i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Wolfson Microelectronics WM8903 audio codec */
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_BOTH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+
+			AVDD-supply  = <&vdd_1v8_vio>;
+			CPVDD-supply = <&vdd_1v8_vio>;
+			DBVDD-supply = <&vdd_1v8_vio>;
+			DCVDD-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	i2c2: i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Atmel touchscreen */
+		touchscreen@4d {
+			compatible = "atmel,maxtouch";
+			reg = <0x4d>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+		};
+	};
+
+	i2c3: i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* AsahiKASEI AK8975 magnetometer sensor */
+		magnetometer@c {
+			compatible = "asahi-kasei,ak8975";
+			reg = <0x0c>;
+
+			vdd-supply = <&vdd_3v3_sen>;
+			vid-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =   "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+		};
+
+		light-sensor@44 {
+			compatible = "isil,isl29023";
+			reg = <0x44>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Q, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			vcc-supply = <&vdd_3v3_sen>;
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply = <&vdd_3v3_sen>;
+			vlogic-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =   "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0x0f>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(L, 1) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_1v8_vio>;
+					vddio-supply = <&vdd_1v8_vio>;
+
+					mount-matrix =  "-1",  "0",  "0",
+							 "0",  "1",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <93750>;
+	};
+
+	i2c5: i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Texas Instruments TPS659110 PMIC */
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_sys>;
+			vcc2-supply = <&vdd_5v0_sys>;
+			vcc3-supply = <&vdd_1v8_vio>;
+			vcc4-supply = <&vdd_1v8_vio>;
+			vcc5-supply = <&vdd_5v0_sys>;
+			vcc6-supply = <&vddio_1v2_ddr>;
+			vcc7-supply = <&vdd_5v0_sys>;
+			vccio-supply = <&vdd_5v0_sys>;
+
+			pmic-sleep-hog {
+				gpio-hog;
+				gpios = <0 GPIO_ACTIVE_HIGH>,
+					<2 GPIO_ACTIVE_HIGH>,
+					<6 GPIO_ACTIVE_HIGH>,
+					<8 GPIO_ACTIVE_HIGH>;
+				output-high;
+			};
+
+			regulators {
+				/* VDD1 is not used by Chagall */
+
+				vddio_1v2_ddr: vdd2 {
+					regulator-name = "vddio_1v2_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8_vio: vio {
+					regulator-name = "vdd_1v8_gen";
+					/* FIXME: eMMC won't work, if set to 1.8 V */
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* eMMC VDD */
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_emmc_core";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDD */
+				vdd_usd: ldo2 {
+					regulator-name = "vdd_usd";
+					regulator-min-microvolt = <3200000>;
+					regulator-max-microvolt = <3200000>;
+				};
+
+				/* uSD slot VDDIO */
+				vddio_usd: ldo3 {
+					regulator-name = "vddio_usd";
+					regulator-min-microvolt = <1900000>;
+					regulator-max-microvolt = <3200000>;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo5 {
+					regulator-name = "vdd_1v3_cam_isp";
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+				};
+
+				ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 5) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1770000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	vdd_5v0_sys: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_sys: regulator-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <300000>;
+		gpio = <&gpio TEGRA_GPIO(W, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_3v3_sen: regulator-sensors {
+		compatible = "regulator-fixed";
+		regulator-name = "sen_3v3_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio TEGRA_GPIO(K, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_5v0_bl: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_vbus_usb1: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbus_micro_usb";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_vbus_usb3: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbus_typea_usb";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(CC, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		/* Set DEV_OFF + PWR_OFF_SET bit in DCDC control register of TPS65911 PMIC  */
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x81>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* SAMSUNG K4P8G304EB FGC1 */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000002 0x00000003 0x0000000c 0x00000007
+					0x00000009 0x00000001 0x00000002 0x00000006
+					0x00000001 0x00000000 0x00000004 0x00000004
+					0x04040001 0x000d090c 0x7026120d 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* ELPIDA EDB8132B2MA 8D_F */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000002 0x00000003 0x0000000c 0x00000007
+					0x00000009 0x00000001 0x00000002 0x00000006
+					0x00000001 0x00000000 0x00000004 0x00000004
+					0x04040001 0x000d090c 0x7026120d 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* SAMSUNG K4P8G304EB FGC2 */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emem-configuration = < 0x00000008 0xc0000060
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000d 0x00000002 0x00000002 0x00000008
+					0x00000002 0x00000000 0x00000004 0x00000005
+					0x05040002 0x00110b10 0x70281811 0x001f0000 >;
+			};
+		};
+
+		emc-timings-3 {
+			/* HYNIX H9TCNNN8JDMMPR NGM */
+			nvidia,ram-code = <3>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emem-configuration = < 0x00000008 0xc0000060
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000d 0x00000002 0x00000002 0x00000008
+					0x00000002 0x00000000 0x00000004 0x00000005
+					0x05040002 0x00110b10 0x70281811 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* SAMSUNG K4P8G304EB FGC1 */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010082>;
+				nvidia,emc-mode-2 = <0x00020004>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000024>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000017
+					0x00000033 0x00000010 0x00000007 0x00000007
+					0x00000007 0x00000002 0x0000000a 0x00000007
+					0x00000007 0x00000003 0x00000002 0x00000000
+					0x00000003 0x00000007 0x00000004 0x0000000d
+					0x0000000e 0x000005e9 0x00000000 0x0000017a
+					0x00000002 0x00000002 0x00000007 0x00000000
+					0x00000001 0x0000000c 0x00000038 0x00000038
+					0x00000006 0x00000014 0x00000009 0x00000004
+					0x00000002 0x00000680 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0x001d0084
+					0x00008000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00038000 0x00038000 0x00038000
+					0x00038000 0x00080220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000090 0x000c000c 0xa0f10404 0x00000000
+					0x00000000 0x80000ce6 0xe0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* ELPIDA EDB8132B2MA 8D_F */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010082>;
+				nvidia,emc-mode-2 = <0x00020004>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000024>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000017
+					0x00000033 0x00000010 0x00000007 0x00000007
+					0x00000007 0x00000002 0x0000000a 0x00000007
+					0x00000007 0x00000003 0x00000002 0x00000000
+					0x00000003 0x00000007 0x00000004 0x0000000d
+					0x0000000e 0x000005e9 0x00000000 0x0000017a
+					0x00000002 0x00000002 0x00000007 0x00000000
+					0x00000001 0x0000000c 0x00000038 0x00000038
+					0x00000006 0x00000014 0x00000009 0x00000004
+					0x00000002 0x00000680 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0x001d0084
+					0x00008000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x00060220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000090 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000ce6 0xe0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* SAMSUNG K4P8G304EB FGC2 */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000004 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000005 0x00000004
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020006>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000030>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000045 0x00000016 0x00000009 0x00000008
+					0x00000009 0x00000003 0x0000000d 0x00000009
+					0x00000009 0x00000005 0x00000003 0x00000000
+					0x00000004 0x0000000a 0x00000006 0x0000000d
+					0x00000010 0x000007df 0x00000000 0x000001f7
+					0x00000003 0x00000003 0x00000009 0x00000000
+					0x00000001 0x0000000f 0x0000004b 0x0000004b
+					0x00000008 0x0000001b 0x0000000c 0x00000004
+					0x00000002 0x000008aa 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0xf0120091
+					0x00008000 0x007f8008 0x007f8008 0x007f8008
+					0x007f8008 0x007f8008 0x007f8008 0x007f8008
+					0x007f8008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x00080220 0x0200003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000c0 0x000e000e 0xa0f10000 0x00000000
+					0x00000000 0x800010d9 0xf0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-3 {
+			/* HYNIX H9TCNNN8JDMMPR NGM */
+			nvidia,ram-code = <3>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xd0000000 0xff00ff00 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020006>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000030>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000045 0x00000016 0x00000009 0x00000008
+					0x00000009 0x00000003 0x0000000d 0x00000009
+					0x00000009 0x00000005 0x00000003 0x00000000
+					0x00000004 0x00000009 0x00000006 0x0000000d
+					0x00000010 0x000007df 0x00000000 0x000001f7
+					0x00000003 0x00000003 0x00000009 0x00000000
+					0x00000001 0x0000000f 0x0000004b 0x0000004b
+					0x00000008 0x0000001b 0x0000000c 0x00000004
+					0x00000002 0x000008aa 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0xf0120091
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000a0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000c0 0x000e000e 0xa0f10000 0x00000000
+					0x00000000 0x800010d9 0xe0000000 0xff00ff88 >;
+			};
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		i2s@70080400 { /* i2s1 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 { /* i2s3 */
+			status = "okay";
+		};
+	};
+
+	sdmmc1: mmc@78000000 {
+		status = "okay";
+
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		bus-width = <4>;
+
+		vmmc-supply = <&vdd_usd>; /* ldo2 */
+		vqmmc-supply = <&vddio_usd>; /* ldo3 */
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* Azurewave AW-AH663 BCM4330B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+		non-removable;
+	};
+
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "otg";
+		vbus-supply = <&vdd_vbus_usb1>;
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "otg";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+	};
+
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_vbus_usb3>;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_bl>;
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <15>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	display-panel {
+		compatible = "hannstar,hsd101pww2", "panel-lvds";
+
+		width-mm = <217>;
+		height-mm = <136>;
+
+		data-mapping = "jeida-24";
+
+		panel-timing {
+			/* 1280x800@60Hz */
+			clock-frequency = <68000000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <48>;
+			hback-porch = <18>;
+			hsync-len = <30>;
+			vsync-len = <5>;
+			vfront-porch = <3>;
+			vback-porch = <12>;
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+
+		switch-dock-insert {
+			label = "Chagall Dock";
+			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_DOCK>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-lineout-detect {
+			label = "Audio dock line-out detect";
+			gpios = <&gpio TEGRA_GPIO(S, 3) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LINEOUT_INSERT>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-625000000;
+		/delete-node/ opp-667000000;
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-625000000-1200;
+		/delete-node/ opp-625000000-1250;
+		/delete-node/ opp-667000000-1200;
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	sound {
+		compatible = "pegatron,tegra-audio-wm8903-chagall",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Pegatron Chagall WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"IN1R", "Mic Jack",
+			"DMICDAT", "Int Mic";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,headset;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * Chagall from getting too hot from a user's tactile
+		 * perspective. The CPU zone is intended to protect
+		 * silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-peripherals-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra30-peripherals-opp.dtsi
new file mode 100644
index 000000000000..a2d557155114
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-peripherals-opp.dtsi
@@ -0,0 +1,1648 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	core_opp_table: opp-table-core {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		core_opp_950: opp-950000 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-level = <950000>;
+		};
+
+		core_opp_1000: opp-1000000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-level = <1000000>;
+		};
+
+		core_opp_1050: opp-1050000 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-level = <1050000>;
+		};
+
+		core_opp_1100: opp-1100000 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-level = <1100000>;
+		};
+
+		core_opp_1150: opp-1150000 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-level = <1150000>;
+		};
+
+		core_opp_1200: opp-1200000 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-level = <1200000>;
+		};
+
+		core_opp_1250: opp-1250000 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-level = <1250000>;
+		};
+
+		core_opp_1300: opp-1300000 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-level = <1300000>;
+		};
+
+		core_opp_1350: opp-1350000 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-level = <1350000>;
+		};
+	};
+
+	emc_icc_dvfs_opp_table: opp-table-emc {
+		compatible = "operating-points-v2";
+
+		opp-12750000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-12750000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-12750000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-25500000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <25500000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-25500000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <25500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-25500000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <25500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-27000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <27000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-27000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <27000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-27000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <27000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-51000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <51000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-51000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <51000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-51000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <51000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-54000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <54000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-54000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <54000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-54000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <54000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-102000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-102000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-102000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-108000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <108000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-108000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <108000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-204000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+			opp-suspend;
+		};
+
+		opp-204000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+			opp-suspend;
+		};
+
+		opp-266500000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <266500000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-266500000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <266500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-333500000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-333500000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-333500000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-375000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <375000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-375000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <375000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-375000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <375000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-400000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-400000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-400000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-416000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-450000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <450000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-450000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <450000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-500000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-500000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-533000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-533000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-625000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <625000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-625000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <625000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-667000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <667000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-750000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <750000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-800000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-900000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <900000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	emc_bw_dfs_opp_table: opp-table-actmon {
+		compatible = "operating-points-v2";
+
+		opp-12750000 {
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <102000>;
+		};
+
+		opp-25500000 {
+			opp-hz = /bits/ 64 <25500000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <204000>;
+		};
+
+		opp-27000000 {
+			opp-hz = /bits/ 64 <27000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <216000>;
+		};
+
+		opp-51000000 {
+			opp-hz = /bits/ 64 <51000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <408000>;
+		};
+
+		opp-54000000 {
+			opp-hz = /bits/ 64 <54000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <432000>;
+		};
+
+		opp-102000000 {
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <816000>;
+		};
+
+		opp-108000000 {
+			opp-hz = /bits/ 64 <108000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <864000>;
+		};
+
+		opp-204000000 {
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <1632000>;
+			opp-suspend;
+		};
+
+		opp-266500000 {
+			opp-hz = /bits/ 64 <266500000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <2132000>;
+		};
+
+		opp-333500000 {
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <2668000>;
+		};
+
+		opp-375000000 {
+			opp-hz = /bits/ 64 <375000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <3000000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <3200000>;
+		};
+
+		opp-416000000 {
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <3328000>;
+		};
+
+		opp-450000000 {
+			opp-hz = /bits/ 64 <450000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <3600000>;
+		};
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <4000000>;
+		};
+
+		opp-533000000 {
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <4264000>;
+		};
+
+		opp-625000000 {
+			opp-hz = /bits/ 64 <625000000>;
+			opp-supported-hw = <0x000E>;
+			opp-peak-kBps = <5000000>;
+		};
+
+		opp-667000000 {
+			opp-hz = /bits/ 64 <667000000>;
+			opp-supported-hw = <0x0006>;
+			opp-peak-kBps = <5336000>;
+		};
+
+		opp-750000000 {
+			opp-hz = /bits/ 64 <750000000>;
+			opp-supported-hw = <0x0004>;
+			opp-peak-kBps = <6000000>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x0004>;
+			opp-peak-kBps = <6400000>;
+		};
+
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-supported-hw = <0x0004>;
+			opp-peak-kBps = <7200000>;
+		};
+	};
+
+	pcie_dvfs_opp_table: opp-table-pcie {
+		compatible = "operating-points-v2";
+
+		opp-250000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <250000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	host1x_dvfs_opp_table: opp-table-host1x {
+		compatible = "operating-points-v2";
+
+		opp-152000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-188000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <188000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-222000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <222000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-242000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <242000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-254000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <254000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-267000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	mpe_dvfs_opp_table: opp-table-mpe {
+		compatible = "operating-points-v2";
+
+		opp-234000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <234000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	vi_dvfs_opp_table: opp-table-vi {
+		compatible = "operating-points-v2";
+
+		opp-216000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <216000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-219000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <219000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-267000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-300000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-371000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <371000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-409000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <409000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-425000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <425000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-470000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <470000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+	};
+
+	epp_dvfs_opp_table: opp-table-epp {
+		compatible = "operating-points-v2";
+
+		opp-267000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	gr2d_dvfs_opp_table: opp-table-gr2d {
+		compatible = "operating-points-v2";
+
+		opp-267000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	gr3d_dvfs_opp_table: opp-table-gr3d {
+		compatible = "operating-points-v2";
+
+		opp-234000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <234000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>, <&core_opp_1000>;
+		};
+
+		opp-247000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>, <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>, <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>, <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>, <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>, <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>, <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>, <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>, <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>, <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>, <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>, <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>, <&core_opp_1350>;
+		};
+	};
+
+	disp1_dvfs_opp_table: opp-table-disp1 {
+		compatible = "operating-points-v2";
+
+		opp-120000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <120000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-155000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <155000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-268000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <268000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1050>;
+		};
+	};
+
+	disp2_dvfs_opp_table: opp-table-disp2 {
+		compatible = "operating-points-v2";
+
+		opp-120000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <120000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-155000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <155000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-268000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <268000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1050>;
+		};
+	};
+
+	hdmi_dvfs_opp_table: opp-table-hdmi {
+		compatible = "operating-points-v2";
+
+		opp-148500000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <148500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	tvo_dvfs_opp_table: opp-table-tvo {
+		compatible = "operating-points-v2";
+
+		opp-297000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <297000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+	};
+
+	dsia_dvfs_opp_table: opp-table-dsia {
+		compatible = "operating-points-v2";
+
+		opp-275000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <275000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	dsib_dvfs_opp_table: opp-table-dsib {
+		compatible = "operating-points-v2";
+
+		opp-275000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <275000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sclk_dvfs_opp_table: opp-table-sclk {
+		compatible = "operating-points-v2";
+
+		opp-51000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <51000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-136000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <136000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-164000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <164000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-191000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <191000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-205000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <205000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-216000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <216000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-227000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <227000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-267000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-334000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <334000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-378000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <378000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+	};
+
+	pll_c_dvfs_opp_table: opp-table-pllc {
+		compatible = "operating-points-v2";
+
+		opp-533000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-667000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <667000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-800000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-1066000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <1066000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-1200000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	pll_e_dvfs_opp_table: opp-table-plle {
+		compatible = "operating-points-v2";
+
+		opp-100000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	pll_m_dvfs_opp_table: opp-table-pllm {
+		compatible = "operating-points-v2";
+
+		opp-533000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-667000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <667000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-800000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-1066000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <1066000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	vde_dvfs_opp_table: opp-table-vde {
+		compatible = "operating-points-v2";
+
+		opp-228000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <228000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-275000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <275000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-352000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <352000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-400000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-437000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <437000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	fuse_burn_dvfs_opp_table: opp-table-fuseburn {
+		compatible = "operating-points-v2";
+
+		opp-26000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <26000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1150>;
+		};
+	};
+
+	nor_dvfs_opp_table: opp-table-nor {
+		compatible = "operating-points-v2";
+
+		opp-108000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <108000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-115000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <115000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-130000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <130000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-133000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1150>;
+		};
+	};
+
+	pwm_dvfs_opp_table: opp-table-pwm {
+		compatible = "operating-points-v2";
+
+		opp-408000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sbc1_dvfs_opp_table: opp-table-sbc1 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc2_dvfs_opp_table: opp-table-sbc2 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc3_dvfs_opp_table: opp-table-sbc3 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc4_dvfs_opp_table: opp-table-sbc4 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc5_dvfs_opp_table: opp-table-sbc5 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc6_dvfs_opp_table: opp-table-sbc6 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sdmmc1_dvfs_opp_table: opp-table-sdmmc1 {
+		compatible = "operating-points-v2";
+
+		opp-104000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <104000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-208000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <208000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sdmmc3_dvfs_opp_table: opp-table-sdmmc3 {
+		compatible = "operating-points-v2";
+
+		opp-104000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <104000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-208000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <208000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	usbd_dvfs_opp_table: opp-table-usbd {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	usb2_dvfs_opp_table: opp-table-usb2 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	usb3_dvfs_opp_table: opp-table-usb3 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/nvidia/tegra30.dtsi
index 55ae050042ce..f866fa7b55a5 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30.dtsi
@@ -4,6 +4,10 @@
 #include <dt-bindings/memory/tegra30-mc.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/tegra-pmc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30-peripherals-opp.dtsi"
 
 / {
 	compatible = "nvidia,tegra30";
@@ -19,12 +23,12 @@
 	pcie@3000 {
 		compatible = "nvidia,tegra30-pcie";
 		device_type = "pci";
-		reg = <0x00003000 0x00000800   /* PADS registers */
-		       0x00003800 0x00000200   /* AFI registers */
-		       0x10000000 0x10000000>; /* configuration space */
+		reg = <0x00003000 0x00000800>, /* PADS registers */
+		      <0x00003800 0x00000200>, /* AFI registers */
+		      <0x10000000 0x10000000>; /* configuration space */
 		reg-names = "pads", "afi", "cs";
-		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH   /* controller interrupt */
-			      GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
 		interrupt-names = "intr", "msi";
 
 		#interrupt-cells = <1>;
@@ -35,12 +39,12 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 
-		ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000   /* port 0 configuration space */
-			  0x82000000 0 0x00001000 0x00001000 0 0x00001000   /* port 1 configuration space */
-			  0x82000000 0 0x00004000 0x00004000 0 0x00001000   /* port 2 configuration space */
-			  0x81000000 0 0          0x02000000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x20000000 0x20000000 0 0x08000000   /* non-prefetchable memory */
-			  0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */
+		ranges = <0x02000000 0 0x00000000 0x00000000 0 0x00001000>, /* port 0 configuration space */
+			 <0x02000000 0 0x00001000 0x00001000 0 0x00001000>, /* port 1 configuration space */
+			 <0x02000000 0 0x00004000 0x00004000 0 0x00001000>, /* port 2 configuration space */
+			 <0x01000000 0 0          0x02000000 0 0x00010000>, /* downstream I/O */
+			 <0x02000000 0 0x20000000 0x20000000 0 0x08000000>, /* non-prefetchable memory */
+			 <0x42000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */
 
 		clocks = <&tegra_car TEGRA30_CLK_PCIE>,
 			 <&tegra_car TEGRA30_CLK_AFI>,
@@ -51,6 +55,8 @@
 			 <&tegra_car 72>,
 			 <&tegra_car 74>;
 		reset-names = "pex", "afi", "pcie_x";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&pcie_dvfs_opp_table>;
 		status = "disabled";
 
 		pci@1,0 {
@@ -96,28 +102,32 @@
 		};
 	};
 
-	iram@40000000 {
+	sram@40000000 {
 		compatible = "mmio-sram";
 		reg = <0x40000000 0x40000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x40000000 0x40000>;
 
-		vde_pool: vde@400 {
+		vde_pool: sram@400 {
 			reg = <0x400 0x3fc00>;
 			pool;
 		};
 	};
 
 	host1x@50000000 {
-		compatible = "nvidia,tegra30-host1x", "simple-bus";
+		compatible = "nvidia,tegra30-host1x";
 		reg = <0x50000000 0x00024000>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */
 			     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */
+		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA30_CLK_HOST1X>;
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		clock-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA30_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 		iommus = <&mc TEGRA_SWGROUP_HC>;
+		power-domains = <&pd_heg>;
+		operating-points-v2 = <&host1x_dvfs_opp_table>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -131,8 +141,12 @@
 			clocks = <&tegra_car TEGRA30_CLK_MPE>;
 			resets = <&tegra_car 60>;
 			reset-names = "mpe";
+			power-domains = <&pd_mpe>;
+			operating-points-v2 = <&mpe_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_MPE>;
+
+			status = "disabled";
 		};
 
 		vi@54080000 {
@@ -142,8 +156,12 @@
 			clocks = <&tegra_car TEGRA30_CLK_VI>;
 			resets = <&tegra_car 20>;
 			reset-names = "vi";
+			power-domains = <&pd_venc>;
+			operating-points-v2 = <&vi_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_VI>;
+
+			status = "disabled";
 		};
 
 		epp@540c0000 {
@@ -153,8 +171,12 @@
 			clocks = <&tegra_car TEGRA30_CLK_EPP>;
 			resets = <&tegra_car 19>;
 			reset-names = "epp";
+			power-domains = <&pd_heg>;
+			operating-points-v2 = <&epp_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_EPP>;
+
+			status = "disabled";
 		};
 
 		isp@54100000 {
@@ -164,8 +186,11 @@
 			clocks = <&tegra_car TEGRA30_CLK_ISP>;
 			resets = <&tegra_car 23>;
 			reset-names = "isp";
+			power-domains = <&pd_venc>;
 
 			iommus = <&mc TEGRA_SWGROUP_ISP>;
+
+			status = "disabled";
 		};
 
 		gr2d@54140000 {
@@ -173,8 +198,10 @@
 			reg = <0x54140000 0x00040000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA30_CLK_GR2D>;
-			resets = <&tegra_car 21>;
-			reset-names = "2d";
+			resets = <&tegra_car 21>, <&mc TEGRA30_MC_RESET_2D>;
+			reset-names = "2d", "mc";
+			power-domains = <&pd_heg>;
+			operating-points-v2 = <&gr2d_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_G2>;
 		};
@@ -182,19 +209,24 @@
 		gr3d@54180000 {
 			compatible = "nvidia,tegra30-gr3d";
 			reg = <0x54180000 0x00040000>;
-			clocks = <&tegra_car TEGRA30_CLK_GR3D
-				  &tegra_car TEGRA30_CLK_GR3D2>;
+			clocks = <&tegra_car TEGRA30_CLK_GR3D>,
+				 <&tegra_car TEGRA30_CLK_GR3D2>;
 			clock-names = "3d", "3d2";
 			resets = <&tegra_car 24>,
-				 <&tegra_car 98>;
-			reset-names = "3d", "3d2";
+				 <&tegra_car 98>,
+				 <&mc TEGRA30_MC_RESET_3D>,
+				 <&mc TEGRA30_MC_RESET_3D2>;
+			reset-names = "3d", "3d2", "mc", "mc2";
+			power-domains = <&pd_3d0>, <&pd_3d1>;
+			power-domain-names = "3d0", "3d1";
+			operating-points-v2 = <&gr3d_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_NV>,
 				 <&mc TEGRA_SWGROUP_NV2>;
 		};
 
 		dc@54200000 {
-			compatible = "nvidia,tegra30-dc", "nvidia,tegra20-dc";
+			compatible = "nvidia,tegra30-dc";
 			reg = <0x54200000 0x00040000>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA30_CLK_DISP1>,
@@ -202,11 +234,24 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 27>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp1_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_DC>;
 
 			nvidia,head = <0>;
 
+			interconnects = <&mc TEGRA30_MC_DISPLAY0A &emc>,
+					<&mc TEGRA30_MC_DISPLAY0B &emc>,
+					<&mc TEGRA30_MC_DISPLAY1B &emc>,
+					<&mc TEGRA30_MC_DISPLAY0C &emc>,
+					<&mc TEGRA30_MC_DISPLAYHC &emc>;
+			interconnect-names = "wina",
+					     "winb",
+					     "winb-vfilter",
+					     "winc",
+					     "cursor";
+
 			rgb {
 				status = "disabled";
 			};
@@ -221,11 +266,24 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 26>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp2_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_DCB>;
 
 			nvidia,head = <1>;
 
+			interconnects = <&mc TEGRA30_MC_DISPLAY0AB &emc>,
+					<&mc TEGRA30_MC_DISPLAY0BB &emc>,
+					<&mc TEGRA30_MC_DISPLAY1BB &emc>,
+					<&mc TEGRA30_MC_DISPLAY0CB &emc>,
+					<&mc TEGRA30_MC_DISPLAYHCB &emc>;
+			interconnect-names = "wina",
+					     "winb",
+					     "winb-vfilter",
+					     "winc",
+					     "cursor";
+
 			rgb {
 				status = "disabled";
 			};
@@ -240,6 +298,8 @@
 			clock-names = "hdmi", "parent";
 			resets = <&tegra_car 51>;
 			reset-names = "hdmi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&hdmi_dvfs_opp_table>;
 			status = "disabled";
 		};
 
@@ -248,15 +308,34 @@
 			reg = <0x542c0000 0x00040000>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA30_CLK_TVO>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&tvo_dvfs_opp_table>;
 			status = "disabled";
 		};
 
 		dsi@54300000 {
 			compatible = "nvidia,tegra30-dsi";
 			reg = <0x54300000 0x00040000>;
-			clocks = <&tegra_car TEGRA30_CLK_DSIA>;
+			clocks = <&tegra_car TEGRA30_CLK_DSIA>,
+				 <&tegra_car TEGRA30_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "parent";
 			resets = <&tegra_car 48>;
 			reset-names = "dsi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&dsia_dvfs_opp_table>;
+			status = "disabled";
+		};
+
+		dsi@54400000 {
+			compatible = "nvidia,tegra30-dsi";
+			reg = <0x54400000 0x00040000>;
+			clocks = <&tegra_car TEGRA30_CLK_DSIB>,
+				 <&tegra_car TEGRA30_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "parent";
+			resets = <&tegra_car 84>;
+			reset-names = "dsi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&dsib_dvfs_opp_table>;
 			status = "disabled";
 		};
 	};
@@ -272,8 +351,8 @@
 
 	intc: interrupt-controller@50041000 {
 		compatible = "arm,cortex-a9-gic";
-		reg = <0x50041000 0x1000
-		       0x50040100 0x0100>;
+		reg = <0x50041000 0x1000>,
+		      <0x50040100 0x0100>;
 		interrupt-controller;
 		#interrupt-cells = <3>;
 		interrupt-parent = <&intc>;
@@ -317,6 +396,34 @@
 		reg = <0x60006000 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
+
+		pll-c {
+			compatible = "nvidia,tegra30-pllc";
+			clocks = <&tegra_car TEGRA30_CLK_PLL_C>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&pll_c_dvfs_opp_table>;
+		};
+
+		pll-e {
+			compatible = "nvidia,tegra30-plle";
+			clocks = <&tegra_car TEGRA30_CLK_PLL_E>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&pll_e_dvfs_opp_table>;
+		};
+
+		pll-m {
+			compatible = "nvidia,tegra30-pllm";
+			clocks = <&tegra_car TEGRA30_CLK_PLL_M>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&pll_m_dvfs_opp_table>;
+		};
+
+		sclk {
+			compatible = "nvidia,tegra30-sclk";
+			clocks = <&tegra_car TEGRA30_CLK_SCLK>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&sclk_dvfs_opp_table>;
+		};
 	};
 
 	flow-controller@60007000 {
@@ -370,7 +477,7 @@
 		reg = <0x6000c000 0x150>; /* AHB Arbitration + Gizmo Controller */
 	};
 
-	actmon@6000c800 {
+	actmon: actmon@6000c800 {
 		compatible = "nvidia,tegra30-actmon";
 		reg = <0x6000c800 0x400>;
 		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
@@ -379,6 +486,10 @@
 		clock-names = "actmon", "emc";
 		resets = <&tegra_car TEGRA30_CLK_ACTMON>;
 		reset-names = "actmon";
+		operating-points-v2 = <&emc_bw_dfs_opp_table>;
+		interconnects = <&mc TEGRA30_MC_MPCORER &emc>;
+		interconnect-names = "cpu-read";
+		#cooling-cells = <2>;
 	};
 
 	gpio: gpio@6000d000 {
@@ -396,22 +507,20 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 248>;
-		*/
 	};
 
 	vde@6001a000 {
 		compatible = "nvidia,tegra30-vde", "nvidia,tegra20-vde";
-		reg = <0x6001a000 0x1000   /* Syntax Engine */
-		       0x6001b000 0x1000   /* Video Bitstream Engine */
-		       0x6001c000  0x100   /* Macroblock Engine */
-		       0x6001c200  0x100   /* Post-processing Engine */
-		       0x6001c400  0x100   /* Motion Compensation Engine */
-		       0x6001c600  0x100   /* Transform Engine */
-		       0x6001c800  0x100   /* Pixel prediction block */
-		       0x6001ca00  0x100   /* Video DMA */
-		       0x6001d800  0x400>; /* Video frame controls */
+		reg = <0x6001a000 0x1000>, /* Syntax Engine */
+		      <0x6001b000 0x1000>, /* Video Bitstream Engine */
+		      <0x6001c000  0x100>, /* Macroblock Engine */
+		      <0x6001c200  0x100>, /* Post-processing Engine */
+		      <0x6001c400  0x100>, /* Motion Compensation Engine */
+		      <0x6001c600  0x100>, /* Transform Engine */
+		      <0x6001c800  0x100>, /* Pixel prediction block */
+		      <0x6001ca00  0x100>, /* Video DMA */
+		      <0x6001d800  0x400>; /* Video frame controls */
 		reg-names = "sxe", "bsev", "mbe", "ppe", "mce",
 			    "tfe", "ppb", "vdma", "frameid";
 		iram = <&vde_pool>; /* IRAM region */
@@ -423,18 +532,20 @@
 		reset-names = "vde", "mc";
 		resets = <&tegra_car 61>, <&mc TEGRA30_MC_RESET_VDE>;
 		iommus = <&mc TEGRA_SWGROUP_VDE>;
+		power-domains = <&pd_vde>;
+		operating-points-v2 = <&vde_dvfs_opp_table>;
 	};
 
 	apbmisc@70000800 {
 		compatible = "nvidia,tegra30-apbmisc", "nvidia,tegra20-apbmisc";
-		reg = <0x70000800 0x64   /* Chip revision */
-		       0x70000008 0x04>; /* Strapping options */
+		reg = <0x70000800 0x64>, /* Chip revision */
+		      <0x70000008 0x04>; /* Strapping options */
 	};
 
 	pinmux: pinmux@70000868 {
 		compatible = "nvidia,tegra30-pinmux";
-		reg = <0x70000868 0xd4    /* Pad control registers */
-		       0x70003000 0x3e4>; /* Mux registers */
+		reg = <0x70000868 0x0d4>, /* Pad control registers */
+		      <0x70003000 0x3e4>; /* Mux registers */
 	};
 
 	/*
@@ -452,7 +563,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -465,7 +575,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -478,7 +587,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -491,7 +599,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -504,7 +611,6 @@
 		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTE>;
 		resets = <&tegra_car 66>;
-		reset-names = "serial";
 		dmas = <&apbdma 20>, <&apbdma 20>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -520,6 +626,8 @@
 		clock-names = "gmi";
 		resets = <&tegra_car 42>;
 		reset-names = "gmi";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&nor_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -530,16 +638,11 @@
 		clocks = <&tegra_car TEGRA30_CLK_PWM>;
 		resets = <&tegra_car 17>;
 		reset-names = "pwm";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&pwm_dvfs_opp_table>;
 		status = "disabled";
 	};
 
-	rtc@7000e000 {
-		compatible = "nvidia,tegra30-rtc", "nvidia,tegra20-rtc";
-		reg = <0x7000e000 0x100>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA30_CLK_RTC>;
-	};
-
 	i2c@7000c000 {
 		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
@@ -621,7 +724,7 @@
 	};
 
 	spi@7000d400 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000d400 0x200>;
 		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -631,11 +734,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 15>, <&apbdma 15>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc1_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000d600 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000d600 0x200>;
 		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -645,11 +750,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 16>, <&apbdma 16>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000d800 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000d800 0x200>;
 		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -659,11 +766,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 17>, <&apbdma 17>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000da00 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000da00 0x200>;
 		interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -673,11 +782,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 18>, <&apbdma 18>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc4_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000dc00 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000dc00 0x200>;
 		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -687,11 +798,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 27>, <&apbdma 27>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc5_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000de00 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000de00 0x200>;
 		interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -701,9 +814,18 @@
 		reset-names = "spi";
 		dmas = <&apbdma 28>, <&apbdma 28>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc6_dvfs_opp_table>;
 		status = "disabled";
 	};
 
+	rtc@7000e000 {
+		compatible = "nvidia,tegra30-rtc", "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA30_CLK_RTC>;
+	};
+
 	kbc@7000e200 {
 		compatible = "nvidia,tegra30-kbc", "nvidia,tegra20-kbc";
 		reg = <0x7000e200 0x100>;
@@ -714,11 +836,78 @@
 		status = "disabled";
 	};
 
-	pmc@7000e400 {
+	tegra_pmc: pmc@7000e400 {
 		compatible = "nvidia,tegra30-pmc";
 		reg = <0x7000e400 0x400>;
 		clocks = <&tegra_car TEGRA30_CLK_PCLK>, <&clk32k_in>;
 		clock-names = "pclk", "clk32k_in";
+		#clock-cells = <1>;
+
+		pd_core: core-domain {
+			#power-domain-cells = <0>;
+			operating-points-v2 = <&core_opp_table>;
+		};
+
+		powergates {
+			pd_heg: heg {
+				clocks = <&tegra_car TEGRA30_CLK_GR2D>,
+					 <&tegra_car TEGRA30_CLK_EPP>,
+					 <&tegra_car TEGRA30_CLK_HOST1X>;
+				resets = <&mc TEGRA30_MC_RESET_2D>,
+					 <&mc TEGRA30_MC_RESET_EPP>,
+					 <&mc TEGRA30_MC_RESET_HC>,
+					 <&tegra_car TEGRA30_CLK_GR2D>,
+					 <&tegra_car TEGRA30_CLK_EPP>,
+					 <&tegra_car TEGRA30_CLK_HOST1X>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_mpe: mpe {
+				clocks = <&tegra_car TEGRA30_CLK_MPE>;
+				resets = <&mc TEGRA30_MC_RESET_MPE>,
+					 <&tegra_car TEGRA30_CLK_MPE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_3d0: td {
+				clocks = <&tegra_car TEGRA30_CLK_GR3D>;
+				resets = <&mc TEGRA30_MC_RESET_3D>,
+					 <&tegra_car TEGRA30_CLK_GR3D>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_3d1: td2 {
+				clocks = <&tegra_car TEGRA30_CLK_GR3D2>;
+				resets = <&mc TEGRA30_MC_RESET_3D2>,
+					 <&tegra_car TEGRA30_CLK_GR3D2>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_vde: vdec {
+				clocks = <&tegra_car TEGRA30_CLK_VDE>;
+				resets = <&mc TEGRA30_MC_RESET_VDE>,
+					 <&tegra_car TEGRA30_CLK_VDE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_venc: venc {
+				clocks = <&tegra_car TEGRA30_CLK_ISP>,
+					 <&tegra_car TEGRA30_CLK_VI>,
+					 <&tegra_car TEGRA30_CLK_CSI>;
+				resets = <&mc TEGRA30_MC_RESET_ISP>,
+					 <&mc TEGRA30_MC_RESET_VI>,
+					 <&tegra_car TEGRA30_CLK_ISP>,
+					 <&tegra_car 20 /* VI */>,
+					 <&tegra_car TEGRA30_CLK_CSI>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+		};
 	};
 
 	mc: memory-controller@7000f000 {
@@ -731,15 +920,20 @@
 
 		#iommu-cells = <1>;
 		#reset-cells = <1>;
+		#interconnect-cells = <1>;
 	};
 
-	memory-controller@7000f400 {
+	emc: memory-controller@7000f400 {
 		compatible = "nvidia,tegra30-emc";
 		reg = <0x7000f400 0x400>;
 		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_EMC>;
+		power-domains = <&pd_core>;
 
 		nvidia,memory-controller = <&mc>;
+		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
+
+		#interconnect-cells = <0>;
 	};
 
 	fuse@7000f800 {
@@ -749,6 +943,22 @@
 		clock-names = "fuse";
 		resets = <&tegra_car 39>;
 		reset-names = "fuse";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&fuse_burn_dvfs_opp_table>;
+	};
+
+	tsensor: tsensor@70014000 {
+		compatible = "nvidia,tegra30-tsensor";
+		reg = <0x70014000 0x500>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA30_CLK_TSENSOR>;
+		resets = <&tegra_car TEGRA30_CLK_TSENSOR>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_TSENSOR>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_CLK_M>;
+		assigned-clock-rates = <500000>;
+
+		#thermal-sensor-cells = <1>;
 	};
 
 	hda@70030000 {
@@ -768,8 +978,8 @@
 
 	ahub@70080000 {
 		compatible = "nvidia,tegra30-ahub";
-		reg = <0x70080000 0x200
-		       0x70080200 0x100>;
+		reg = <0x70080000 0x200>,
+		      <0x70080200 0x100>;
 		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_D_AUDIO>,
 			 <&tegra_car TEGRA30_CLK_APBIF>;
@@ -849,48 +1059,56 @@
 		};
 	};
 
-	sdhci@78000000 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+	mmc@78000000 {
+		compatible = "nvidia,tegra30-sdhci";
 		reg = <0x78000000 0x200>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_SDMMC1>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 14>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc1_dvfs_opp_table>;
 		status = "disabled";
 	};
 
-	sdhci@78000200 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+	mmc@78000200 {
+		compatible = "nvidia,tegra30-sdhci";
 		reg = <0x78000200 0x200>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_SDMMC2>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 9>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
-	sdhci@78000400 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+	mmc@78000400 {
+		compatible = "nvidia,tegra30-sdhci";
 		reg = <0x78000400 0x200>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 69>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
-	sdhci@78000600 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+	mmc@78000600 {
+		compatible = "nvidia,tegra30-sdhci";
 		reg = <0x78000600 0x200>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_SDMMC4>;
+		clock-names = "sdhci";
 		resets = <&tegra_car 15>;
 		reset-names = "sdhci";
 		status = "disabled";
 	};
 
 	usb@7d000000 {
-		compatible = "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra30-ehci";
 		reg = <0x7d000000 0x4000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -899,12 +1117,16 @@
 		reset-names = "usb";
 		nvidia,needs-double-reset;
 		nvidia,phy = <&phy1>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usbd_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	phy1: usb-phy@7d000000 {
 		compatible = "nvidia,tegra30-usb-phy";
-		reg = <0x7d000000 0x4000 0x7d000000 0x4000>;
+		reg = <0x7d000000 0x4000>,
+		      <0x7d000000 0x4000>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA30_CLK_USBD>,
 			 <&tegra_car TEGRA30_CLK_PLL_U>,
@@ -912,6 +1134,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 22>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <9>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -924,11 +1147,12 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,has-utmi-pad-registers;
+		nvidia,pmc = <&tegra_pmc 0>;
 		status = "disabled";
 	};
 
 	usb@7d004000 {
-		compatible = "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra30-ehci";
 		reg = <0x7d004000 0x4000>;
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -936,12 +1160,16 @@
 		resets = <&tegra_car 58>;
 		reset-names = "usb";
 		nvidia,phy = <&phy2>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	phy2: usb-phy@7d004000 {
 		compatible = "nvidia,tegra30-usb-phy";
-		reg = <0x7d004000 0x4000 0x7d000000 0x4000>;
+		reg = <0x7d004000 0x4000>,
+		      <0x7d000000 0x4000>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA30_CLK_USB2>,
 			 <&tegra_car TEGRA30_CLK_PLL_U>,
@@ -949,6 +1177,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 58>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <9>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -960,11 +1189,12 @@
 		nvidia,xcvr-hsslew = <32>;
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
+		nvidia,pmc = <&tegra_pmc 2>;
 		status = "disabled";
 	};
 
 	usb@7d008000 {
-		compatible = "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra30-ehci";
 		reg = <0x7d008000 0x4000>;
 		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -972,12 +1202,16 @@
 		resets = <&tegra_car 59>;
 		reset-names = "usb";
 		nvidia,phy = <&phy3>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	phy3: usb-phy@7d008000 {
 		compatible = "nvidia,tegra30-usb-phy";
-		reg = <0x7d008000 0x4000 0x7d000000 0x4000>;
+		reg = <0x7d008000 0x4000>,
+		      <0x7d000000 0x4000>;
+		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA30_CLK_USB3>,
 			 <&tegra_car TEGRA30_CLK_PLL_U>,
@@ -985,6 +1219,7 @@
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 59>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
+		#phy-cells = <0>;
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
@@ -996,6 +1231,7 @@
 		nvidia,xcvr-hsslew = <32>;
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
+		nvidia,pmc = <&tegra_pmc 1>;
 		status = "disabled";
 	};
 
@@ -1003,32 +1239,36 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <1>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <2>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <3>;
 			clocks = <&tegra_car TEGRA30_CLK_CCLK_G>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -1038,9 +1278,66 @@
 			     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&{/cpus/cpu@0}>,
-				     <&{/cpus/cpu@1}>,
-				     <&{/cpus/cpu@2}>,
-				     <&{/cpus/cpu@3}>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	thermal-zones {
+		tsensor0-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&tsensor 0>;
+
+			trips {
+				level1_trip: dvfs-alert {
+					/* throttle at 80C until temperature drops to 79.8C */
+					temperature = <80000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				level2_trip: cpu-div2-throttle {
+					/* hardware CPU x2 freq throttle at 85C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "hot";
+				};
+
+				level3_trip: soc-critical {
+					/* hardware shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&level1_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		tsensor1-thermal {
+			status = "disabled";
+
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <0>; /* milliseconds */
+
+			thermal-sensors = <&tsensor 1>;
+
+			trips {
+				dvfs-alert {
+					temperature = <80000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/Makefile b/arch/arm/boot/dts/nxp/Makefile
new file mode 100644
index 000000000000..db44e7a0a198
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += imx
+subdir-y += lpc
+subdir-y += ls
+subdir-y += mxs
+subdir-y += vf
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
new file mode 100644
index 000000000000..a724d1a7a9a0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -0,0 +1,391 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_IMX1) += \
+	imx1-ads.dtb \
+	imx1-apf9328.dtb
+dtb-$(CONFIG_SOC_IMX25) += \
+	imx25-eukrea-mbimxsd25-baseboard.dtb \
+	imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb \
+	imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb \
+	imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb \
+	imx25-karo-tx25.dtb \
+	imx25-pdk.dtb
+dtb-$(CONFIG_SOC_IMX27) += \
+	imx27-apf27.dtb \
+	imx27-apf27dev.dtb \
+	imx27-eukrea-mbimxsd27-baseboard.dtb \
+	imx27-pdk.dtb \
+	imx27-phytec-phycore-rdk.dtb \
+	imx27-phytec-phycard-s-rdk.dtb
+dtb-$(CONFIG_SOC_IMX31) += \
+	imx31-bug.dtb \
+	imx31-lite.dtb
+dtb-$(CONFIG_SOC_IMX35) += \
+	imx35-eukrea-mbimxsd35-baseboard.dtb \
+	imx35-pdk.dtb
+dtb-$(CONFIG_SOC_IMX50) += \
+	imx50-evk.dtb \
+	imx50-kobo-aura.dtb
+dtb-$(CONFIG_SOC_IMX51) += \
+	imx51-apf51.dtb \
+	imx51-apf51dev.dtb \
+	imx51-babbage.dtb \
+	imx51-digi-connectcore-jsk.dtb \
+	imx51-eukrea-mbimxsd51-baseboard.dtb \
+	imx51-ts4800.dtb \
+	imx51-zii-rdu1.dtb \
+	imx51-zii-scu2-mezz.dtb \
+	imx51-zii-scu3-esb.dtb
+dtb-$(CONFIG_SOC_IMX53) += \
+	imx53-ard.dtb \
+	imx53-cx9020.dtb \
+	imx53-kp-ddc.dtb \
+	imx53-kp-hsc.dtb \
+	imx53-m53evk.dtb \
+	imx53-m53menlo.dtb \
+	imx53-mba53.dtb \
+	imx53-ppd.dtb \
+	imx53-qsb.dtb \
+	imx53-qsrb.dtb \
+	imx53-sk-imx53.dtb \
+	imx53-sk-imx53-atm0700d4-lvds.dtb \
+	imx53-sk-imx53-atm0700d4-rgb.dtb \
+	imx53-smd.dtb \
+	imx53-tx53-x03x.dtb \
+	imx53-tx53-x13x.dtb \
+	imx53-usbarmory.dtb \
+	imx53-voipac-bsb.dtb
+dtb-$(CONFIG_SOC_IMX6Q) += \
+	imx6dl-alti6p.dtb \
+	imx6dl-apf6dev.dtb \
+	imx6dl-aristainetos_4.dtb \
+	imx6dl-aristainetos_7.dtb \
+	imx6dl-aristainetos2_4.dtb \
+	imx6dl-aristainetos2_7.dtb \
+	imx6dl-colibri-aster.dtb \
+	imx6dl-colibri-eval-v3.dtb \
+	imx6dl-colibri-iris.dtb \
+	imx6dl-colibri-iris-v2.dtb \
+	imx6dl-cubox-i.dtb \
+	imx6dl-cubox-i-emmc-som-v15.dtb \
+	imx6dl-cubox-i-som-v15.dtb \
+	imx6dl-dfi-fs700-m60.dtb \
+	imx6dl-dhcom-picoitx.dtb \
+	imx6dl-eckelmann-ci4x10.dtb \
+	imx6dl-emcon-avari.dtb \
+	imx6dl-gw51xx.dtb \
+	imx6dl-gw52xx.dtb \
+	imx6dl-gw53xx.dtb \
+	imx6dl-gw54xx.dtb \
+	imx6dl-gw551x.dtb \
+	imx6dl-gw552x.dtb \
+	imx6dl-gw553x.dtb \
+	imx6dl-gw560x.dtb \
+	imx6dl-gw5903.dtb \
+	imx6dl-gw5904.dtb \
+	imx6dl-gw5907.dtb \
+	imx6dl-gw5910.dtb \
+	imx6dl-gw5912.dtb \
+	imx6dl-gw5913.dtb \
+	imx6dl-hummingboard.dtb \
+	imx6dl-hummingboard-emmc-som-v15.dtb \
+	imx6dl-hummingboard-som-v15.dtb \
+	imx6dl-hummingboard2.dtb \
+	imx6dl-hummingboard2-emmc-som-v15.dtb \
+	imx6dl-hummingboard2-som-v15.dtb \
+	imx6dl-icore.dtb \
+	imx6dl-icore-mipi.dtb \
+	imx6dl-icore-rqs.dtb \
+	imx6dl-lanmcu.dtb \
+	imx6dl-mamoj.dtb \
+	imx6dl-mba6a.dtb \
+	imx6dl-mba6b.dtb \
+	imx6dl-nit6xlite.dtb \
+	imx6dl-nitrogen6x.dtb \
+	imx6dl-phytec-mira-rdk-nand.dtb \
+	imx6dl-phytec-pbab01.dtb \
+	imx6dl-pico-dwarf.dtb \
+	imx6dl-pico-hobbit.dtb \
+	imx6dl-pico-nymph.dtb \
+	imx6dl-pico-pi.dtb \
+	imx6dl-plybas.dtb \
+	imx6dl-plym2m.dtb \
+	imx6dl-prtmvt.dtb \
+	imx6dl-prtrvt.dtb \
+	imx6dl-prtvt7.dtb \
+	imx6dl-rex-basic.dtb \
+	imx6dl-riotboard.dtb \
+	imx6dl-sabreauto.dtb \
+	imx6dl-sabrelite.dtb \
+	imx6dl-sabresd.dtb \
+	imx6dl-savageboard.dtb \
+	imx6dl-skov-revc-lt2.dtb \
+	imx6dl-skov-revc-lt6.dtb \
+	imx6dl-solidsense.dtb \
+	imx6dl-ts4900.dtb \
+	imx6dl-ts7970.dtb \
+	imx6dl-tx6dl-comtft.dtb \
+	imx6dl-tx6s-8034.dtb \
+	imx6dl-tx6s-8034-mb7.dtb \
+	imx6dl-tx6s-8035.dtb \
+	imx6dl-tx6s-8035-mb7.dtb \
+	imx6dl-tx6u-801x.dtb \
+	imx6dl-tx6u-80xx-mb7.dtb \
+	imx6dl-tx6u-8033.dtb \
+	imx6dl-tx6u-8033-mb7.dtb \
+	imx6dl-tx6u-811x.dtb \
+	imx6dl-tx6u-81xx-mb7.dtb \
+	imx6dl-udoo.dtb \
+	imx6dl-victgo.dtb \
+	imx6dl-vicut1.dtb \
+	imx6dl-wandboard.dtb \
+	imx6dl-wandboard-revb1.dtb \
+	imx6dl-wandboard-revd1.dtb \
+	imx6dl-yapp4-draco.dtb \
+	imx6dl-yapp4-hydra.dtb \
+	imx6dl-yapp4-lynx.dtb \
+	imx6dl-yapp4-orion.dtb \
+	imx6dl-yapp4-phoenix.dtb \
+	imx6dl-yapp4-ursa.dtb \
+	imx6q-apalis-eval.dtb \
+	imx6q-apalis-ixora.dtb \
+	imx6q-apalis-ixora-v1.1.dtb \
+	imx6q-apalis-ixora-v1.2.dtb \
+	imx6q-apf6dev.dtb \
+	imx6q-arm2.dtb \
+	imx6q-b450v3.dtb \
+	imx6q-b650v3.dtb \
+	imx6q-b850v3.dtb \
+	imx6q-bosch-acc.dtb \
+	imx6q-cm-fx6.dtb \
+	imx6q-cubox-i.dtb \
+	imx6q-cubox-i-emmc-som-v15.dtb \
+	imx6q-cubox-i-som-v15.dtb \
+	imx6q-dfi-fs700-m60.dtb \
+	imx6q-dhcom-pdk2.dtb \
+	imx6q-display5-tianma-tm070-1280x768.dtb \
+	imx6q-dmo-edmqmx6.dtb \
+	imx6q-dms-ba16.dtb \
+	imx6q-ds.dtb \
+	imx6q-emcon-avari.dtb \
+	imx6q-evi.dtb \
+	imx6dl-b105pv2.dtb \
+	imx6dl-b105v2.dtb \
+	imx6dl-b125v2.dtb \
+	imx6dl-b125pv2.dtb \
+	imx6dl-b155v2.dtb \
+	imx6q-gk802.dtb \
+	imx6q-gw51xx.dtb \
+	imx6q-gw52xx.dtb \
+	imx6q-gw53xx.dtb \
+	imx6q-gw5400-a.dtb \
+	imx6q-gw54xx.dtb \
+	imx6q-gw551x.dtb \
+	imx6q-gw552x.dtb \
+	imx6q-gw553x.dtb \
+	imx6q-gw560x.dtb \
+	imx6q-gw5903.dtb \
+	imx6q-gw5904.dtb \
+	imx6q-gw5907.dtb \
+	imx6q-gw5910.dtb \
+	imx6q-gw5912.dtb \
+	imx6q-gw5913.dtb \
+	imx6q-h100.dtb \
+	imx6q-hummingboard.dtb \
+	imx6q-hummingboard-emmc-som-v15.dtb \
+	imx6q-hummingboard-som-v15.dtb \
+	imx6q-hummingboard2.dtb \
+	imx6q-hummingboard2-emmc-som-v15.dtb \
+	imx6q-hummingboard2-som-v15.dtb \
+	imx6q-icore.dtb \
+	imx6q-icore-mipi.dtb \
+	imx6q-icore-ofcap10.dtb \
+	imx6q-icore-ofcap12.dtb \
+	imx6q-icore-rqs.dtb \
+	imx6q-kp-tpc.dtb \
+	imx6q-logicpd.dtb \
+	imx6q-marsboard.dtb \
+	imx6q-mba6a.dtb \
+	imx6q-mba6b.dtb \
+	imx6q-mccmon6.dtb \
+	imx6q-nitrogen6x.dtb \
+	imx6q-nitrogen6_max.dtb \
+	imx6q-nitrogen6_som2.dtb \
+	imx6q-novena.dtb \
+	imx6q-phytec-mira-rdk-emmc.dtb \
+	imx6q-phytec-mira-rdk-nand.dtb \
+	imx6q-phytec-pbab01.dtb \
+	imx6q-pico-dwarf.dtb \
+	imx6q-pico-hobbit.dtb \
+	imx6q-pico-nymph.dtb \
+	imx6q-pico-pi.dtb \
+	imx6q-pistachio.dtb \
+	imx6q-prti6q.dtb \
+	imx6q-prtwd2.dtb \
+	imx6q-rex-pro.dtb \
+	imx6q-sabreauto.dtb \
+	imx6q-sabrelite.dtb \
+	imx6q-sabresd.dtb \
+	imx6q-savageboard.dtb \
+	imx6q-sbc6x.dtb \
+	imx6q-skov-revc-lt2.dtb \
+	imx6q-skov-revc-lt6.dtb \
+	imx6q-skov-reve-mi1010ait-1cp1.dtb \
+	imx6q-solidsense.dtb \
+	imx6q-tbs2910.dtb \
+	imx6q-ts4900.dtb \
+	imx6q-ts7970.dtb \
+	imx6q-tx6q-1010.dtb \
+	imx6q-tx6q-1010-comtft.dtb \
+	imx6q-tx6q-1020.dtb \
+	imx6q-tx6q-1020-comtft.dtb \
+	imx6q-tx6q-1036.dtb \
+	imx6q-tx6q-1036-mb7.dtb \
+	imx6q-tx6q-10x0-mb7.dtb \
+	imx6q-tx6q-1110.dtb \
+	imx6q-tx6q-11x0-mb7.dtb \
+	imx6q-udoo.dtb \
+	imx6q-utilite-pro.dtb \
+	imx6q-var-dt6customboard.dtb \
+	imx6q-var-mx6customboard.dtb \
+	imx6q-vicut1.dtb \
+	imx6q-wandboard.dtb \
+	imx6q-wandboard-revb1.dtb \
+	imx6q-wandboard-revd1.dtb \
+	imx6q-yapp4-crux.dtb \
+	imx6q-yapp4-pegasus.dtb \
+	imx6q-zii-rdu2.dtb \
+	imx6qp-mba6b.dtb \
+	imx6qp-nitrogen6_max.dtb \
+	imx6qp-nitrogen6_som2.dtb \
+	imx6qp-phytec-mira-rdk-nand.dtb \
+	imx6qp-prtwd3.dtb \
+	imx6qp-sabreauto.dtb \
+	imx6qp-sabresd.dtb \
+	imx6qp-tx6qp-8037.dtb \
+	imx6qp-tx6qp-8037-mb7.dtb \
+	imx6qp-tx6qp-8137.dtb \
+	imx6qp-tx6qp-8137-mb7.dtb \
+	imx6qp-vicutp.dtb \
+	imx6qp-wandboard-revd1.dtb \
+	imx6qp-yapp4-crux-plus.dtb \
+	imx6qp-yapp4-pegasus-plus.dtb \
+	imx6qp-zii-rdu2.dtb \
+	imx6s-dhcom-drc02.dtb
+dtb-$(CONFIG_SOC_IMX6SL) += \
+	imx6sl-evk.dtb \
+	imx6sl-kobo-aura2.dtb \
+	imx6sl-tolino-shine2hd.dtb \
+	imx6sl-tolino-shine3.dtb \
+	imx6sl-tolino-vision.dtb \
+	imx6sl-tolino-vision5.dtb \
+	imx6sl-warp.dtb
+dtb-$(CONFIG_SOC_IMX6SLL) += \
+	imx6sll-evk.dtb \
+	imx6sll-kobo-clarahd.dtb \
+	imx6sll-kobo-librah2o.dtb
+dtb-$(CONFIG_SOC_IMX6SX) += \
+	imx6sx-nitrogen6sx.dtb \
+	imx6sx-sabreauto.dtb \
+	imx6sx-sdb-reva.dtb \
+	imx6sx-sdb-sai.dtb \
+	imx6sx-sdb.dtb \
+	imx6sx-sdb-mqs.dtb \
+	imx6sx-softing-vining-2000.dtb \
+	imx6sx-udoo-neo-basic.dtb \
+	imx6sx-udoo-neo-extended.dtb \
+	imx6sx-udoo-neo-full.dtb
+dtb-$(CONFIG_SOC_IMX6UL) += \
+	imx6ul-14x14-evk.dtb \
+	imx6ul-ccimx6ulsbcexpress.dtb \
+	imx6ul-ccimx6ulsbcpro.dtb \
+	imx6ul-geam.dtb \
+	imx6ul-isiot-emmc.dtb \
+	imx6ul-isiot-nand.dtb \
+	imx6ul-kontron-bl.dtb \
+	imx6ul-kontron-bl-43.dtb \
+	imx6ul-liteboard.dtb \
+	imx6ul-tqma6ul1-mba6ulx.dtb \
+	imx6ul-tqma6ul2-mba6ulx.dtb \
+	imx6ul-tqma6ul2l-mba6ulx.dtb \
+	imx6ul-opos6uldev.dtb \
+	imx6ul-pico-dwarf.dtb \
+	imx6ul-pico-hobbit.dtb \
+	imx6ul-pico-pi.dtb \
+	imx6ul-phytec-segin-ff-rdk-emmc.dtb \
+	imx6ul-phytec-segin-ff-rdk-nand.dtb \
+	imx6ul-prti6g.dtb \
+	imx6ul-tx6ul-0010.dtb \
+	imx6ul-tx6ul-0011.dtb \
+	imx6ul-tx6ul-mainboard.dtb \
+	imx6ull-14x14-evk.dtb \
+	imx6ull-colibri-aster.dtb \
+	imx6ull-colibri-emmc-aster.dtb \
+	imx6ull-colibri-emmc-eval-v3.dtb \
+	imx6ull-colibri-emmc-iris.dtb \
+	imx6ull-colibri-emmc-iris-v2.dtb \
+	imx6ull-colibri-eval-v3.dtb \
+	imx6ull-colibri-iris.dtb \
+	imx6ull-colibri-iris-v2.dtb \
+	imx6ull-colibri-wifi-aster.dtb \
+	imx6ull-colibri-wifi-eval-v3.dtb \
+	imx6ull-colibri-wifi-iris.dtb \
+	imx6ull-colibri-wifi-iris-v2.dtb \
+	imx6ull-dhcom-drc02.dtb \
+	imx6ull-dhcom-pdk2.dtb \
+	imx6ull-dhcom-picoitx.dtb \
+	imx6ull-dhcor-maveo-box.dtb \
+	imx6ull-jozacp.dtb \
+	imx6ull-kontron-bl.dtb \
+	imx6ull-myir-mys-6ulx-eval.dtb \
+	imx6ull-opos6uldev.dtb \
+	imx6ull-phytec-segin-ff-rdk-nand.dtb \
+	imx6ull-phytec-segin-ff-rdk-emmc.dtb \
+	imx6ull-phytec-segin-lc-rdk-nand.dtb \
+	imx6ull-phytec-tauri-emmc.dtb \
+	imx6ull-phytec-tauri-nand.dtb \
+	imx6ull-tarragon-master.dtb \
+	imx6ull-tarragon-micro.dtb \
+	imx6ull-tarragon-slave.dtb \
+	imx6ull-tarragon-slavext.dtb \
+	imx6ull-tqma6ull2-mba6ulx.dtb \
+	imx6ull-tqma6ull2l-mba6ulx.dtb \
+	imx6ulz-14x14-evk.dtb \
+	imx6ulz-bsh-smm-m2.dtb
+dtb-$(CONFIG_SOC_IMX7D) += \
+	imx7d-cl-som-imx7.dtb \
+	imx7d-colibri-aster.dtb \
+	imx7d-colibri-emmc-aster.dtb \
+	imx7d-colibri-emmc-iris.dtb \
+	imx7d-colibri-emmc-iris-v2.dtb \
+	imx7d-colibri-emmc-eval-v3.dtb \
+	imx7d-colibri-eval-v3.dtb \
+	imx7d-colibri-iris.dtb \
+	imx7d-colibri-iris-v2.dtb \
+	imx7d-flex-concentrator.dtb \
+	imx7d-flex-concentrator-mfg.dtb \
+	imx7d-mba7.dtb \
+	imx7d-meerkat96.dtb \
+	imx7d-nitrogen7.dtb \
+	imx7d-pico-dwarf.dtb \
+	imx7d-pico-hobbit.dtb \
+	imx7d-pico-nymph.dtb \
+	imx7d-pico-pi.dtb \
+	imx7d-remarkable2.dtb \
+	imx7d-sbc-imx7.dtb \
+	imx7d-sdb.dtb \
+	imx7d-sdb-reva.dtb \
+	imx7d-sdb-sht11.dtb \
+	imx7d-smegw01.dtb \
+	imx7d-zii-rmu2.dtb \
+	imx7d-zii-rpu2.dtb \
+	imx7s-colibri-aster.dtb \
+	imx7s-colibri-eval-v3.dtb \
+	imx7s-colibri-iris.dtb \
+	imx7s-colibri-iris-v2.dtb \
+	imx7s-mba7.dtb \
+	imx7s-warp.dtb
+dtb-$(CONFIG_SOC_IMX7ULP) += \
+	imx7ulp-com.dtb \
+	imx7ulp-evk.dtb
+dtb-$(CONFIG_SOC_IMXRT) += \
+	imxrt1050-evk.dtb
diff --git a/arch/arm/boot/dts/e60k02.dtsi b/arch/arm/boot/dts/nxp/imx/e60k02.dtsi
index 6472b056a001..dd03e3860f97 100644
--- a/arch/arm/boot/dts/e60k02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/e60k02.dtsi
@@ -22,14 +22,14 @@
 	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -41,14 +41,15 @@
 	leds: leds {
 		compatible = "gpio-leds";
 
-		on {
+		led {
 			label = "e60k02:white:on";
 			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 	};
 
-	memory {
+	memory@80000000 {
+		device_type = "memory";
 		reg = <0x80000000 0x20000000>;
 	};
 
@@ -103,7 +104,16 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	/* TODO: CYTTSP5 touch controller at 0x24 */
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cyttsp5_gpio>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&ldo5_reg>;
+	};
 
 	/* TODO: TPS65185 PMIC for E Ink at 0x68 */
 
@@ -116,6 +126,8 @@
 	ricoh619: pmic@32 {
 		compatible = "ricoh,rc5t619";
 		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 		system-power-controller;
 
 		regulators {
@@ -265,11 +277,6 @@
 				regulator-name = "LDORTC1";
 				regulator-boot-on;
 			};
-
-			ldortc2_reg: LDORTC2 {
-				regulator-name = "LDORTC2";
-				regulator-boot-on;
-			};
 		};
 	};
 };
@@ -280,6 +287,12 @@
 };
 
 &uart1 {
+	/* J4, through-hole */
+	status = "okay";
+};
+
+&uart4 {
+	/* TP198, next to J4, SMD pads */
 	status = "okay";
 };
 
@@ -298,6 +311,7 @@
 
 &usbotg1 {
 	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	disable-over-current;
 	srp-disable;
 	hnp-disable;
diff --git a/arch/arm/boot/dts/nxp/imx/e70k02.dtsi b/arch/arm/boot/dts/nxp/imx/e70k02.dtsi
new file mode 100644
index 000000000000..4e1bf080eaca
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/e70k02.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021 Andreas Kemnade
+ * based on works
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ * and
+ * Copyright (C) 2014 Ricoh Electronic Devices Co., Ltd
+ *
+ * Netronix E70K02 board common.
+ * This board is equipped with different SoCs and
+ * found in ebook-readers like the Kobo Clara HD (with i.MX6SLL) and
+ * the Tolino Shine 3 (with i.MX6SL)
+ */
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc3;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-cover {
+			label = "Cover";
+			gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-pageup {
+			label = "PageUp";
+			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PAGEUP>;
+		};
+
+		key-pagedown {
+			label = "PageDown";
+			gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PAGEDOWN>;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+
+		led {
+			label = "e70k02:white:on";
+			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	lm3630a: backlight@36 {
+		reg = <0x36>;
+		compatible = "ti,lm3630a";
+		enable-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0>;
+			label = "backlight_warm";
+			default-brightness = <0>;
+			max-brightness = <255>;
+		};
+
+		led@1 {
+			reg = <1>;
+			led-sources = <1>;
+			label = "backlight_cold";
+			default-brightness = <0>;
+			max-brightness = <255>;
+		};
+	};
+
+	/* TODO: KX122 acceleration sensor a 0x1e */
+
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cyttsp5_gpio>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&ldo5_reg>;
+	};
+
+	/* TODO: SY7636 PMIC for E Ink at 0x62 */
+
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	ricoh619: pmic@32 {
+		compatible = "ricoh,rc5t619";
+		reg = <0x32>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+
+		regulators {
+			dcdc1_reg: DCDC1 {
+				regulator-name = "DCDC1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <900000>;
+					regulator-suspend-min-microvolt = <900000>;
+				};
+			};
+
+			/* Core3_3V3 */
+			dcdc2_reg: DCDC2 {
+				regulator-name = "DCDC2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3300000>;
+					regulator-suspend-min-microvolt = <3300000>;
+				};
+			};
+
+			dcdc3_reg: DCDC3 {
+				regulator-name = "DCDC3";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V2 */
+			dcdc4_reg: DCDC4 {
+				regulator-name = "DCDC4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V8 */
+			dcdc5_reg: DCDC5 {
+				regulator-name = "DCDC5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1700000>;
+					regulator-suspend-min-microvolt = <1700000>;
+				};
+			};
+
+			ldo1_reg: LDO1  {
+				regulator-name = "LDO1";
+				regulator-boot-on;
+			};
+
+			/* Core1_3V3 */
+			ldo2_reg: LDO2  {
+				regulator-name = "LDO2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3000000>;
+					regulator-suspend-min-microvolt = <3000000>;
+				};
+			};
+
+			/* Core5_1V2 */
+			ldo3_reg: LDO3  {
+				regulator-name = "LDO3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-boot-on;
+			};
+
+			/* SPD_3V3 */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* DDR_0V6 */
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* VDD_PWM */
+			ldo7_reg: LDO7 {
+				regulator-name = "LDO7";
+				regulator-boot-on;
+			};
+
+			/* ldo_1v8 */
+			ldo8_reg: LDO8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "LDO9";
+				regulator-boot-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "LDO10";
+				regulator-boot-on;
+			};
+
+			ldortc1_reg: LDORTC1  {
+				regulator-name = "LDORTC1";
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&snvs_rtc {
+	/* we are using the rtc in the pmic, not disabled in imx6sll.dtsi */
+	status = "disabled";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usdhc1 {
+	non-removable;
+	no-1-8-v;
+	status = "okay";
+};
+
+&usdhc3 {
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx1-ads.dts b/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
index 5833fb6f15d8..2c817c4a4c68 100644
--- a/arch/arm/boot/dts/imx1-ads.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <4>;
diff --git a/arch/arm/boot/dts/imx1-apf9328.dts b/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
index 77b21aa7a146..e66eef87a7a4 100644
--- a/arch/arm/boot/dts/imx1-apf9328.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
@@ -45,7 +45,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
@@ -58,10 +58,8 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_eth>;
 		compatible = "davicom,dm9000";
-		reg = <
-			4 0x00c00000 0x2
-			4 0x00c00002 0x2
-		>;
+		reg = <4 0x00c00000 0x2>,
+		      <4 0x00c00002 0x2>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
 		fsl,weim-cs-timing = <0x0000c700 0x19190d01>;
diff --git a/arch/arm/boot/dts/imx1-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx1-pinfunc.h
index 050a1fc46a77..bd2e679cb26c 100644
--- a/arch/arm/boot/dts/imx1-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx1-pinfunc.h
@@ -26,9 +26,9 @@
  *                2 - 0
  *                3 - 1
  *
- * 'pin' is an integer between 0 and 0xbf. i.MX1 has 4 ports with 32 configurable
- * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin
- * number on the specific port (between 0 and 31).
+ * 'pin' is an integer between 0 and 0xbf. i.MX1 has 4 ports with 32
+ * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is
+ * the pin number on the specific port (between 0 and 31).
  */
 
 #define MX1_PAD_A24__A24			0x00 0x004
diff --git a/arch/arm/boot/dts/imx1.dtsi b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
index b30448cde582..1ac10965fdfd 100644
--- a/arch/arm/boot/dts/imx1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
@@ -55,7 +55,7 @@
 
 	clocks {
 		clk32 {
-			compatible = "fsl,imx-clk32", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32000>;
 		};
@@ -68,7 +68,7 @@
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi@200000 {
+		bus@200000 {
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -125,7 +125,7 @@
 			};
 
 			pwm: pwm@208000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx1-pwm";
 				reg = <0x00208000 0x1000>;
 				interrupts = <34>;
@@ -155,7 +155,7 @@
 			};
 		};
 
-		aipi@210000 {
+		bus@210000 {
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -268,9 +268,12 @@
 			status = "disabled";
 		};
 
-		esram: esram@300000 {
+		esram: sram@300000 {
 			compatible = "mmio-sram";
 			reg = <0x00300000 0x20000>;
+			ranges = <0 0x00300000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-cpuimx25.dtsi
index 0703f62d10d1..93a6e4e680b4 100644
--- a/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-cpuimx25.dtsi
@@ -27,7 +27,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
index 7d4301b22b90..6cddb2cc36fe 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&qvga_timings>;
-			qvga_timings: 320x240 {
+			qvga_timings: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
@@ -30,22 +30,15 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_lcd_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_reg_lcd_3v3>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_lcd_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_lcd_3v3>;
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
index 80a7f96de4c6..64b2ffac463b 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_svga_timings>;
-			dvi_svga_timings: 800x600 {
+			dvi_svga_timings: timing0 {
 				clock-frequency = <40000000>;
 				hactive = <800>;
 				vactive = <600>;
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
index 24027a1fb46d..fb074bfdaa8d 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_vga_timings>;
-			dvi_vga_timings: 640x480 {
+			dvi_vga_timings: timing0 {
 				clock-frequency = <31250000>;
 				hactive = <640>;
 				vactive = <480>;
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard.dts
index 0fde90df2b54..c7207ea437c4 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard.dts
@@ -13,12 +13,12 @@
 	model = "Eukrea MBIMXSD25";
 	compatible = "eukrea,mbimxsd25-baseboard", "eukrea,cpuimx25", "fsl,imx25";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		bp1 {
+		button {
 			label = "BP1";
 			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -165,8 +165,6 @@
 };
 
 &usbhost1 {
-	phy_type = "serial";
-	dr_mode = "host";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dts b/arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dts
new file mode 100644
index 000000000000..458b94d3d4ed
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx25.dtsi"
+
+/ {
+	model = "Ka-Ro TX25";
+	compatible = "karo,imx25-tx25", "fsl,imx25";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_fec_phy: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-phy";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 9 0>;
+		enable-active-high;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x02000000 0x90000000 0x02000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX25_PAD_UART1_TXD__UART1_TXD 0x00000020
+			MX25_PAD_UART1_RXD__UART1_RXD 0x000000a0
+			MX25_PAD_UART1_CTS__UART1_CTS 0x00000060
+			MX25_PAD_UART1_RTS__UART1_RTS 0x000000e0
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX25_PAD_D11__GPIO_4_9		0x00000021 /* FEC PHY power on pin */
+			MX25_PAD_D13__GPIO_4_7		0x000000a1 /* FEC reset */
+			MX25_PAD_FEC_MDC__FEC_MDC	0x00000060
+			MX25_PAD_FEC_MDIO__FEC_MDIO	0x000001f0
+			MX25_PAD_FEC_TDATA0__FEC_TDATA0	0x00000060
+			MX25_PAD_FEC_TDATA1__FEC_TDATA1	0x00000060
+			MX25_PAD_FEC_TX_EN__FEC_TX_EN	0x00000060
+			MX25_PAD_FEC_RDATA0__FEC_RDATA0	0x000000c1
+			MX25_PAD_FEC_RDATA1__FEC_RDATA1	0x000000c0
+			MX25_PAD_FEC_RX_DV__FEC_RX_DV	0x000000c0
+			MX25_PAD_FEC_TX_CLK__FEC_TX_CLK	0x000000c0
+		>;
+	};
+
+	pinctrl_nfc: nfcgrp {
+		fsl,pins = <
+			MX25_PAD_NF_CE0__NF_CE0		0x00000001
+			MX25_PAD_NFWE_B__NFWE_B		0x80000000
+			MX25_PAD_NFRE_B__NFRE_B		0x80000000
+			MX25_PAD_NFALE__NFALE		0x80000000
+			MX25_PAD_NFCLE__NFCLE		0x80000000
+			MX25_PAD_NFWP_B__NFWP_B		0x80000000
+			MX25_PAD_NFRB__NFRB		0x000000e0
+			MX25_PAD_D7__D7			0x00000080
+			MX25_PAD_D6__D6			0x00000080
+			MX25_PAD_D5__D5			0x00000080
+			MX25_PAD_D4__D4			0x00000080
+			MX25_PAD_D3__D3			0x00000080
+			MX25_PAD_D2__D2			0x00000080
+			MX25_PAD_D1__D1			0x00000000
+			MX25_PAD_D0__D0			0x00000080
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-reset-gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_fec_phy>;
+	status = "okay";
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nfc>;
+	nand-on-flash-bbt;
+	nand-ecc-mode = "hw";
+	nand-bus-width = <8>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx25-pdk.dts b/arch/arm/boot/dts/nxp/imx/imx25-pdk.dts
index 05cccd12624c..dd176fb54e58 100644
--- a/arch/arm/boot/dts/imx25-pdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-pdk.dts
@@ -16,45 +16,35 @@
 		reg = <0x80000000 0x4000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_fec_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "fec-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 3 0>;
-			enable-active-high;
-		};
+	reg_fec_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 3 0>;
+		enable-active-high;
+	};
 
-		reg_2p5v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-		};
+	reg_2p5v: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+	};
 
-		reg_3p3v: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	reg_3p3v: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
-		reg_can_3v3: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "can-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio4 6 0>;
-		};
+	reg_can_3v3: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 6 0>;
 	};
 
 	sound {
@@ -78,7 +68,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&wvga_timings>;
-			wvga_timings: 640x480 {
+			wvga_timings: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <45>;
@@ -132,6 +122,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks 129>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -304,8 +295,6 @@
 };
 
 &usbhost1 {
-	phy_type = "serial";
-	dr_mode = "host";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx25-pinfunc.h
index f4516ccf2c1a..908caf810351 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx25-pinfunc.h
@@ -82,10 +82,12 @@
 #define MX25_PAD_EB0__EB0			0x040 0x258 0x000 0x00 0x000
 #define MX25_PAD_EB0__AUD4_TXD			0x040 0x258 0x464 0x04 0x000
 #define MX25_PAD_EB0__GPIO_2_12			0x040 0x258 0x000 0x05 0x000
+#define MX25_PAD_EB0__CSPI3_SS0			0x040 0x258 0x4bc 0x06 0x000
 
 #define MX25_PAD_EB1__EB1			0x044 0x25c 0x000 0x00 0x000
 #define MX25_PAD_EB1__AUD4_RXD			0x044 0x25c 0x460 0x04 0x000
 #define MX25_PAD_EB1__GPIO_2_13			0x044 0x25c 0x000 0x05 0x000
+#define MX25_PAD_EB1__CSPI3_SS1			0x044 0x25c 0x4c0 0x06 0x000
 
 #define MX25_PAD_OE__OE				0x048 0x260 0x000 0x00 0x000
 #define MX25_PAD_OE__AUD4_TXC			0x048 0x260 0x000 0x04 0x000
@@ -102,22 +104,27 @@
 #define MX25_PAD_CS4__NF_CE1			0x054 0x264 0x000 0x01 0x000
 #define MX25_PAD_CS4__UART5_CTS			0x054 0x264 0x000 0x03 0x000
 #define MX25_PAD_CS4__GPIO_3_20			0x054 0x264 0x000 0x05 0x000
+#define MX25_PAD_CS4__CSPI3_MOSI		0x054 0x264 0x4b8 0x06 0x000
 
 #define MX25_PAD_CS5__CS5			0x058 0x268 0x000 0x00 0x000
 #define MX25_PAD_CS5__NF_CE2			0x058 0x268 0x000 0x01 0x000
 #define MX25_PAD_CS5__UART5_RTS			0x058 0x268 0x574 0x03 0x000
 #define MX25_PAD_CS5__GPIO_3_21			0x058 0x268 0x000 0x05 0x000
+#define MX25_PAD_CS5__CSPI3_MISO		0x058 0x268 0x4b4 0x06 0x000
 
 #define MX25_PAD_NF_CE0__NF_CE0			0x05c 0x26c 0x000 0x00 0x000
+#define MX25_PAD_NF_CE0__CSPI1_SS3		0x05c 0x26c 0x490 0x01 0x000
 #define MX25_PAD_NF_CE0__GPIO_3_22		0x05c 0x26c 0x000 0x05 0x000
 
 #define MX25_PAD_ECB__ECB			0x060 0x270 0x000 0x00 0x000
 #define MX25_PAD_ECB__UART5_TXD			0x060 0x270 0x000 0x03 0x000
 #define MX25_PAD_ECB__GPIO_3_23			0x060 0x270 0x000 0x05 0x000
+#define MX25_PAD_ECB__CSPI3_SCLK		0x060 0x270 0x4ac 0x06 0x000
 
 #define MX25_PAD_LBA__LBA			0x064 0x274 0x000 0x00 0x000
 #define MX25_PAD_LBA__UART5_RXD			0x064 0x274 0x578 0x03 0x000
 #define MX25_PAD_LBA__GPIO_3_24			0x064 0x274 0x000 0x05 0x000
+#define MX25_PAD_LBA__CSPI3_RDY			0x064 0x274 0x4b0 0x06 0x000
 
 #define MX25_PAD_BCLK__BCLK			0x068 0x000 0x000 0x00 0x000
 #define MX25_PAD_BCLK__GPIO_4_4			0x068 0x000 0x000 0x05 0x000
@@ -251,10 +258,12 @@
 
 #define MX25_PAD_LD12__LD12			0x0f8 0x2f0 0x000 0x00 0x000
 #define MX25_PAD_LD12__CSPI2_MOSI		0x0f8 0x2f0 0x4a0 0x02 0x000
+#define MX25_PAD_LD12__KPP_ROW6			0x0f8 0x2f0 0x544 0x04 0x000
 #define MX25_PAD_LD12__FEC_RDATA3		0x0f8 0x2f0 0x510 0x05 0x001
 
 #define MX25_PAD_LD13__LD13			0x0fc 0x2f4 0x000 0x00 0x000
 #define MX25_PAD_LD13__CSPI2_MISO		0x0fc 0x2f4 0x49c 0x02 0x000
+#define MX25_PAD_LD13__KPP_ROW7			0x0fc 0x2f4 0x548 0x04 0x000
 #define MX25_PAD_LD13__FEC_TDATA2		0x0fc 0x2f4 0x000 0x05 0x000
 
 #define MX25_PAD_LD14__LD14			0x100 0x2f8 0x000 0x00 0x000
@@ -279,7 +288,8 @@
 #define MX25_PAD_OE_ACD__GPIO_1_25		0x114 0x30c 0x000 0x05 0x000
 
 #define MX25_PAD_CONTRAST__CONTRAST		0x118 0x310 0x000 0x00 0x000
-#define MX25_PAD_CONTRAST__CC4			0x118 0x310 0x000 0x01 0x000
+#define MX25_PAD_CONTRAST__GPT4_CAPIN1		0x118 0x310 0x000 0x01 0x000
+#define MX25_PAD_CONTRAST__CSPI2_SS1		0x118 0x310 0x4a8 0x02 0x000
 #define MX25_PAD_CONTRAST__PWM4_PWMO		0x118 0x310 0x000 0x04 0x000
 #define MX25_PAD_CONTRAST__FEC_CRS		0x118 0x310 0x508 0x05 0x001
 #define MX25_PAD_CONTRAST__USBH2_PWR		0x118 0x310 0x000 0x06 0x000
@@ -292,7 +302,7 @@
 #define MX25_PAD_CSI_D2__UART5_RXD		0x120 0x318 0x578 0x01 0x001
 #define MX25_PAD_CSI_D2__SIM1_CLK0		0x120 0x318 0x000 0x04 0x000
 #define MX25_PAD_CSI_D2__GPIO_1_27		0x120 0x318 0x000 0x05 0x000
-#define MX25_PAD_CSI_D2__CSPI3_MOSI		0x120 0x318 0x000 0x07 0x000
+#define MX25_PAD_CSI_D2__CSPI3_MOSI		0x120 0x318 0x4b8 0x07 0x001
 
 #define MX25_PAD_CSI_D3__CSI_D3			0x124 0x31c 0x000 0x00 0x000
 #define MX25_PAD_CSI_D3__UART5_TXD		0x124 0x31c 0x000 0x01 0x000
@@ -304,23 +314,25 @@
 #define MX25_PAD_CSI_D4__UART5_RTS		0x128 0x320 0x574 0x01 0x001
 #define MX25_PAD_CSI_D4__SIM1_VEN0		0x128 0x320 0x000 0x04 0x000
 #define MX25_PAD_CSI_D4__GPIO_1_29		0x128 0x320 0x000 0x05 0x000
-#define MX25_PAD_CSI_D4__CSPI3_SCLK		0x128 0x320 0x000 0x07 0x000
+#define MX25_PAD_CSI_D4__CSPI3_SCLK		0x128 0x320 0x4ac 0x07 0x001
 
 #define MX25_PAD_CSI_D5__CSI_D5			0x12c 0x324 0x000 0x00 0x000
 #define MX25_PAD_CSI_D5__UART5_CTS		0x12c 0x324 0x000 0x01 0x000
 #define MX25_PAD_CSI_D5__SIM1_TX0		0x12c 0x324 0x000 0x04 0x000
 #define MX25_PAD_CSI_D5__GPIO_1_30		0x12c 0x324 0x000 0x05 0x000
-#define MX25_PAD_CSI_D5__CSPI3_RDY		0x12c 0x324 0x000 0x07 0x000
+#define MX25_PAD_CSI_D5__CSPI3_RDY		0x12c 0x324 0x4b0 0x07 0x001
 
 #define MX25_PAD_CSI_D6__CSI_D6			0x130 0x328 0x000 0x00 0x000
 /* SION must be set; see the comment for MX25_PAD_SD1_CMD__ESDHC1_CMD. */
 #define MX25_PAD_CSI_D6__ESDHC2_CMD		0x130 0x328 0x4e0 0x12 0x001
 #define MX25_PAD_CSI_D6__SIM1_PD0		0x130 0x328 0x000 0x04 0x000
 #define MX25_PAD_CSI_D6__GPIO_1_31		0x130 0x328 0x000 0x05 0x000
+#define MX25_PAD_CSI_D6__CSPI3_SS0		0x130 0x328 0x4bc 0x07 0x001
 
 #define MX25_PAD_CSI_D7__CSI_D7			0x134 0x32c 0x000 0x00 0x000
 #define MX25_PAD_CSI_D7__ESDHC2_CLK		0x134 0x32C 0x4dc 0x02 0x001
 #define MX25_PAD_CSI_D7__GPIO_1_6		0x134 0x32c 0x000 0x05 0x000
+#define MX25_PAD_CSI_D7__CSPI3_SS1		0x134 0x32c 0x4c0 0x07 0x001
 
 #define MX25_PAD_CSI_D8__CSI_D8			0x138 0x330 0x000 0x00 0x000
 #define MX25_PAD_CSI_D8__AUD6_RXC		0x138 0x330 0x000 0x02 0x000
@@ -392,7 +404,7 @@
 
 #define MX25_PAD_UART1_RTS__UART1_RTS		0x178 0x370 0x000 0x00 0x000
 #define MX25_PAD_UART1_RTS__CSI_D0		0x178 0x370 0x488 0x01 0x001
-#define MX25_PAD_UART1_RTS__CC3			0x178 0x370 0x000 0x02 0x000
+#define MX25_PAD_UART1_RTS__GPT3_CAPIN1		0x178 0x370 0x000 0x02 0x000
 #define MX25_PAD_UART1_RTS__UART2_DCD		0x178 0x370 0x000 0x03 0x000
 #define MX25_PAD_UART1_RTS__GPIO_4_24		0x178 0x370 0x000 0x05 0x000
 
@@ -409,12 +421,14 @@
 
 #define MX25_PAD_UART2_RTS__UART2_RTS		0x188 0x380 0x000 0x00 0x000
 #define MX25_PAD_UART2_RTS__FEC_COL		0x188 0x380 0x504 0x02 0x002
-#define MX25_PAD_UART2_RTS__CC1			0x188 0x380 0x000 0x03 0x000
+#define MX25_PAD_UART2_RTS__GPT1_CAPIN1		0x188 0x380 0x000 0x03 0x000
 #define MX25_PAD_UART2_RTS__GPIO_4_28		0x188 0x380 0x000 0x05 0x000
+#define MX25_PAD_UART2_RTS__CSPI2_SS3		0x188 0x380 0x000 0x06 0x000
 
 #define MX25_PAD_UART2_CTS__UART2_CTS		0x18c 0x384 0x000 0x00 0x000
 #define MX25_PAD_UART2_CTS__FEC_RX_ERR		0x18c 0x384 0x518 0x02 0x002
 #define MX25_PAD_UART2_CTS__GPIO_4_29		0x18c 0x384 0x000 0x05 0x000
+#define MX25_PAD_UART2_CTS__CSPI3_SS3		0x18c 0x384 0x4c8 0x06 0x001
 
 /*
  * Removing the SION bit from MX25_PAD_*__ESDHCn_CMD breaks detecting an SD
@@ -440,14 +454,17 @@
 #define MX25_PAD_SD1_DATA0__GPIO_2_25		0x198 0x390 0x000 0x05 0x000
 
 #define MX25_PAD_SD1_DATA1__ESDHC1_DAT1		0x19c 0x394 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA1__CSPI2_RDY		0x19c 0x394 0x498 0x01 0x001
 #define MX25_PAD_SD1_DATA1__AUD7_RXD		0x19c 0x394 0x478 0x03 0x000
 #define MX25_PAD_SD1_DATA1__GPIO_2_26		0x19c 0x394 0x000 0x05 0x000
 
 #define MX25_PAD_SD1_DATA2__ESDHC1_DAT2		0x1a0 0x398 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA2__CSPI2_SS0		0x1a0 0x398 0x4a4 0x01 0x001
 #define MX25_PAD_SD1_DATA2__FEC_RX_CLK		0x1a0 0x398 0x514 0x02 0x002
 #define MX25_PAD_SD1_DATA2__GPIO_2_27		0x1a0 0x398 0x000 0x05 0x000
 
 #define MX25_PAD_SD1_DATA3__ESDHC1_DAT3		0x1a4 0x39c 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA3__CSPI2_SS1		0x1a4 0x39c 0x4a8 0x01 0x001
 #define MX25_PAD_SD1_DATA3__FEC_CRS		0x1a4 0x39c 0x508 0x02 0x002
 #define MX25_PAD_SD1_DATA3__GPIO_2_28		0x1a4 0x39c 0x000 0x05 0x000
 
@@ -512,9 +529,11 @@
 
 #define MX25_PAD_FEC_TX_EN__FEC_TX_EN		0x1d8 0x3d0 0x000 0x00 0x000
 #define MX25_PAD_FEC_TX_EN__GPIO_3_9		0x1d8 0x3d0 0x000 0x05 0x000
+#define MX25_PAD_FEC_TX_EN__KPP_ROW4		0x1d8 0x3d0 0x53c 0x06 0x000
 
 #define MX25_PAD_FEC_RDATA0__FEC_RDATA0		0x1dc 0x3d4 0x000 0x00 0x000
 #define MX25_PAD_FEC_RDATA0__GPIO_3_10		0x1dc 0x3d4 0x000 0x05 0x000
+#define MX25_PAD_FEC_RDATA0__KPP_ROW5 		0x1dc 0x3d4 0x540 0x06 0x000
 
 #define MX25_PAD_FEC_RDATA1__FEC_RDATA1		0x1e0 0x3d8 0x000 0x00 0x000
 /*
@@ -544,31 +563,35 @@
 #define MX25_PAD_DE_B__DE_B			0x1f0 0x3ec 0x000 0x00 0x000
 #define MX25_PAD_DE_B__GPIO_2_20		0x1f0 0x3ec 0x000 0x05 0x000
 
-#define MX25_PAD_GPIO_A__GPIO_A			0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__GPIO_1_0		0x1f4 0x3f0 0x000 0x00 0x000
 #define MX25_PAD_GPIO_A__CAN1_TX		0x1f4 0x3f0 0x000 0x06 0x000
 #define MX25_PAD_GPIO_A__USBOTG_PWR		0x1f4 0x3f0 0x000 0x02 0x000
 
-#define MX25_PAD_GPIO_B__GPIO_B			0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__GPIO_1_1		0x1f8 0x3f4 0x000 0x00 0x000
 #define MX25_PAD_GPIO_B__USBOTG_OC		0x1f8 0x3f4 0x57c 0x02 0x001
 #define MX25_PAD_GPIO_B__CAN1_RX		0x1f8 0x3f4 0x480 0x06 0x001
 
-#define MX25_PAD_GPIO_C__GPIO_C			0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__GPIO_1_2		0x1fc 0x3f8 0x000 0x00 0x000
 #define MX25_PAD_GPIO_C__PWM4_PWMO		0x1fc 0x3f8 0x000 0x01 0x000
 #define MX25_PAD_GPIO_C__I2C2_SCL		0x1fc 0x3f8 0x51c 0x02 0x001
 #define MX25_PAD_GPIO_C__KPP_COL4		0x1fc 0x3f8 0x52c 0x03 0x001
+#define MX25_PAD_GPIO_C__GPT2_CAPIN1		0x1fc 0x3f8 0x000 0x04 0x000
+#define MX25_PAD_GPIO_C__CSPI1_SS2		0x1fc 0x3f8 0x000 0x05 0x000
 #define MX25_PAD_GPIO_C__CAN2_TX		0x1fc 0x3f8 0x000 0x06 0x000
+#define MX25_PAD_GPIO_C__CSPI2_SS2		0x1fc 0x3f8 0x000 0x07 0x000
 
-#define MX25_PAD_GPIO_D__GPIO_D			0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__GPIO_1_3		0x200 0x3fc 0x000 0x00 0x000
 #define MX25_PAD_GPIO_D__I2C2_SDA		0x200 0x3fc 0x520 0x02 0x001
 #define MX25_PAD_GPIO_D__CAN2_RX		0x200 0x3fc 0x484 0x06 0x001
+#define MX25_PAD_GPIO_D__CSPI3_SS2		0x200 0x3fc 0x4c4 0x07 0x001
 
-#define MX25_PAD_GPIO_E__GPIO_E			0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__GPIO_1_4		0x204 0x400 0x000 0x00 0x000
 #define MX25_PAD_GPIO_E__I2C3_CLK		0x204 0x400 0x524 0x01 0x002
 #define MX25_PAD_GPIO_E__LD16			0x204 0x400 0x000 0x02 0x000
 #define MX25_PAD_GPIO_E__AUD7_TXD		0x204 0x400 0x000 0x04 0x000
 #define MX25_PAD_GPIO_E__UART4_RXD		0x204 0x400 0x570 0x06 0x002
 
-#define MX25_PAD_GPIO_F__GPIO_F			0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__GPIO_1_5		0x208 0x404 0x000 0x00 0x000
 #define MX25_PAD_GPIO_F__LD17			0x208 0x404 0x000 0x02 0x000
 #define MX25_PAD_GPIO_F__AUD7_TXC		0x208 0x404 0x000 0x04 0x000
 #define MX25_PAD_GPIO_F__UART4_TXD		0x208 0x404 0x000 0x06 0x000
@@ -585,6 +608,7 @@
 #define MX25_PAD_VSTBY_REQ__UART4_RTS		0x214 0x408 0x56c 0x06 0x002
 
 #define MX25_PAD_VSTBY_ACK__VSTBY_ACK		0x218 0x40c 0x000 0x00 0x000
+#define MX25_PAD_VSTBY_ACK__CSPI1_SS3		0x218 0x40c 0x490 0x02 0x001
 #define MX25_PAD_VSTBY_ACK__GPIO_3_18		0x218 0x40c 0x000 0x05 0x000
 
 #define MX25_PAD_POWER_FAIL__POWER_FAIL		0x21c 0x410 0x000 0x00 0x000
diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/nxp/imx/imx25.dtsi
index 9a097ef014af..9cfff2151b7e 100644
--- a/arch/arm/boot/dts/imx25.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx25.dtsi
@@ -62,20 +62,30 @@
 
 	clocks {
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};
 
-	soc {
+	usbphy0: usb-phy0 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
+	usbphy1: usb-phy1 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&asic>;
 		ranges;
 
-		aips@43f00000 { /* AIPS1 */
+		bus@43f00000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -93,7 +103,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f80000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <3>;
 				status = "disabled";
 			};
@@ -104,7 +114,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f84000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <10>;
 				status = "disabled";
 			};
@@ -151,7 +161,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f98000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <4>;
 				status = "disabled";
 			};
@@ -178,12 +188,9 @@
 			};
 
 			kpp: kpp@43fa8000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "fsl,imx25-kpp", "fsl,imx21-kpp";
 				reg = <0x43fa8000 0x4000>;
 				clocks = <&clks 102>;
-				clock-names = "";
 				interrupts = <24>;
 				status = "disabled";
 			};
@@ -200,7 +207,7 @@
 			};
 		};
 
-		spba@50000000 {
+		spba-bus@50000000 {
 			compatible = "fsl,spba-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -332,7 +339,7 @@
 			};
 		};
 
-		aips@53f00000 { /* AIPS2 */
+		bus@53f00000 { /* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -411,7 +418,7 @@
 
 			pwm2: pwm@53fa0000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				reg = <0x53fa0000 0x4000>;
 				clocks = <&clks 106>, <&clks 52>;
 				clock-names = "ipg", "per";
@@ -430,7 +437,7 @@
 
 			pwm3: pwm@53fa8000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				reg = <0x53fa8000 0x4000>;
 				clocks = <&clks 107>, <&clks 52>;
 				clock-names = "ipg", "per";
@@ -453,7 +460,7 @@
 				interrupts = <22>;
 			};
 
-			esdhc1: esdhc@53fb4000 {
+			esdhc1: mmc@53fb4000 {
 				compatible = "fsl,imx25-esdhc";
 				reg = <0x53fb4000 0x4000>;
 				interrupts = <9>;
@@ -462,7 +469,7 @@
 				status = "disabled";
 			};
 
-			esdhc2: esdhc@53fb8000 {
+			esdhc2: mmc@53fb8000 {
 				compatible = "fsl,imx25-esdhc";
 				reg = <0x53fb8000 0x4000>;
 				interrupts = <8>;
@@ -488,7 +495,7 @@
 
 			pwm4: pwm@53fc8000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				reg = <0x53fc8000 0x4000>;
 				clocks = <&clks 108>, <&clks 52>;
 				clock-names = "ipg", "per";
@@ -515,7 +522,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx25-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 112>, <&clks 68>;
@@ -525,25 +532,24 @@
 				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx25.bin";
 			};
 
-			wdog@53fdc000 {
+			watchdog@53fdc000 {
 				compatible = "fsl,imx25-wdt", "fsl,imx21-wdt";
 				reg = <0x53fdc000 0x4000>;
 				clocks = <&clks 126>;
-				clock-names = "";
 				interrupts = <55>;
 			};
 
 			pwm1: pwm@53fe0000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				reg = <0x53fe0000 0x4000>;
 				clocks = <&clks 105>, <&clks 52>;
 				clock-names = "ipg", "per";
 				interrupts = <26>;
 			};
 
-			iim: iim@53ff0000 {
-				compatible = "fsl,imx25-iim", "fsl,imx27-iim";
+			iim: efuse@53ff0000 {
+				compatible = "fsl,imx25-iim";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <19>;
 				clocks = <&clks 99>;
@@ -570,6 +576,9 @@
 				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 1>;
 				fsl,usbphy = <&usbphy1>;
+				maximum-speed = "full-speed";
+				phy_type = "serial";
+				dr_mode = "host";
 				status = "disabled";
 			};
 
@@ -580,10 +589,9 @@
 			};
 
 			dryice@53ffc000 {
-				compatible = "fsl,imx25-dryice", "fsl,imx25-rtc";
+				compatible = "fsl,imx25-rtc";
 				reg = <0x53ffc000 0x4000>;
 				clocks = <&clks 81>;
-				clock-names = "ipg";
 				interrupts = <25 56>;
 			};
 		};
@@ -591,9 +599,12 @@
 		iram: sram@78000000 {
 			compatible = "mmio-sram";
 			reg = <0x78000000 0x20000>;
+			ranges = <0 0x78000000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
-		emi@80000000 {
+		bus@80000000 {
 			compatible = "fsl,emi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -613,22 +624,4 @@
 			};
 		};
 	};
-
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usb-phy@0 {
-			reg = <0>;
-			compatible = "usb-nop-xceiv";
-			#phy-cells = <0>;
-		};
-
-		usbphy1: usb-phy@1 {
-			reg = <1>;
-			compatible = "usb-nop-xceiv";
-			#phy-cells = <0>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/imx27-apf27.dts b/arch/arm/boot/dts/nxp/imx/imx27-apf27.dts
index 745d5d409952..745d5d409952 100644
--- a/arch/arm/boot/dts/imx27-apf27.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-apf27.dts
diff --git a/arch/arm/boot/dts/imx27-apf27dev.dts b/arch/arm/boot/dts/nxp/imx/imx27-apf27dev.dts
index 6f1e8ce9e76e..849306cb4532 100644
--- a/arch/arm/boot/dts/imx27-apf27dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-apf27dev.dts
@@ -16,7 +16,7 @@
 		fsl,pcr = <0xfae80083>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 800x480 {
+			timing0: timing0 {
 				clock-frequency = <33000033>;
 				hactive = <800>;
 				vactive = <480>;
@@ -47,26 +47,19 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_max5821: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "max5821-reg";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
+	reg_max5821: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "max5821-reg";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
index 74110bbcd9d4..c7e923584878 100644
--- a/arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
@@ -33,7 +33,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -90,7 +90,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
diff --git a/arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
index 9c3ec82ec7e5..d78793601306 100644
--- a/arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
@@ -16,7 +16,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 320x240 {
+			timing0: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
@@ -54,22 +54,15 @@
 		};
 	};
 
-	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "simple-bus";
-
-		reg_lcd: regulator@0 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_lcdreg>;
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "LCD";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_lcd: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcdreg>;
+		regulator-name = "LCD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-pdk.dts b/arch/arm/boot/dts/nxp/imx/imx27-pdk.dts
index 35123b7cb6b3..21d436972aa4 100644
--- a/arch/arm/boot/dts/imx27-pdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-pdk.dts
@@ -14,18 +14,12 @@
 		reg = <0xa0000000 0x08000000>;
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+
+	usbphy0: usbphy {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-rdk.dts
index 0cd75dadf292..27c93b9fe049 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-rdk.dts
@@ -19,7 +19,7 @@
 		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 640x480 {
+			timing0: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <112>;
@@ -33,19 +33,12 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 };
 
@@ -75,8 +68,8 @@
 	imx27-phycard-s-rdk {
 		pinctrl_i2c1: i2c1grp {
 			fsl,pins = <
-				MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
-				MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
+				MX27_PAD_I2C_DATA__I2C_DATA 0x0
+				MX27_PAD_I2C_CLK__I2C_CLK 0x0
 			>;
 		};
 
diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
index 52c95248e25d..abc9233c5a1b 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
@@ -18,8 +18,8 @@
 };
 
 &cspi1 {
-	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
-		   <&gpio4 27 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>,
+		   <&gpio4 27 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -34,7 +34,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	at24@52 {
+	eeprom@52 {
 		compatible = "atmel,24c32";
 		pagesize = <32>;
 		reg = <0x52>;
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-rdk.dts
index bf883e45576a..b8048e12e3d9 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-rdk.dts
@@ -19,7 +19,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 240x320 {
+			timing0: timing0 {
 				clock-frequency = <5500000>;
 				hactive = <240>;
 				vactive = <320>;
@@ -37,35 +37,29 @@
 		};
 	};
 
-	regulators {
-		regulator@2 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_csien>;
-			reg = <2>;
-			regulator-name = "CSI_EN";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
-			regulator-always-on;
-		};
+	regulator-2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_csien>;
+		regulator-name = "CSI_EN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
 	};
 
-	usbphy {
-		usbphy2: usbphy@2 {
-			compatible = "usb-nop-xceiv";
-			reg = <2>;
-			vcc-supply = <&reg_5v0>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+	usbphy2: usbphy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_5v0>;
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
 &cspi1 {
 	pinctrl-0 = <&pinctrl_cspi1>, <&pinctrl_cspi1cs1>;
-	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>,
 		   <&gpio4 27 GPIO_ACTIVE_LOW>;
 };
 
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
index 3d10273177e9..e958d7286ae9 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
@@ -15,41 +15,27 @@
 		reg = <0xa0000000 0x08000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	reg_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
-		reg_5v0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "5V0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
+	reg_5v0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			vcc-supply = <&sw3_reg>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+
+	usbphy0: usbphy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&sw3_reg>;
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
@@ -57,12 +43,12 @@
 	status = "okay";
 
 	/* SSI0 <=> PINS_4 (MC13783 Audio) */
-	ssi0 {
+	mux-ssi0 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <0xcb205000>;
 	};
 
-	pins4 {
+	mux-pins4 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <0x00001000>;
 	};
@@ -188,13 +174,13 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	at24@52 {
+	eeprom@52 {
 		compatible = "atmel,24c32";
 		pagesize = <32>;
 		reg = <0x52>;
 	};
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -322,7 +308,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
diff --git a/arch/arm/boot/dts/imx27-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx27-pinfunc.h
index 1514d80a3112..75aea0c701d4 100644
--- a/arch/arm/boot/dts/imx27-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx27-pinfunc.h
@@ -26,9 +26,9 @@
  *                2 - 0
  *                3 - 1
  *
- * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable
- * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin
- * number on the specific port (between 0 and 31).
+ * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32
+ * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is
+ * the pin number on the specific port (between 0 and 31).
  */
 
 #define MX27_PAD_USBH2_CLK__USBH2_CLK                      0x00 0x000
diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
index f3464cf52e49..ec472695c71e 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
@@ -74,14 +74,14 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi@10000000 { /* AIPI1 */
+		aipi1: bus@10000000 { /* AIPI1 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -96,10 +96,10 @@
 					 <&clks IMX27_CLK_DMA_AHB_GATE>;
 				clock-names = "ipg", "ahb";
 				#dma-cells = <1>;
-				#dma-channels = <16>;
+				dma-channels = <16>;
 			};
 
-			wdog: wdog@10002000 {
+			wdog: watchdog@10002000 {
 				compatible = "fsl,imx27-wdt", "fsl,imx21-wdt";
 				reg = <0x10002000 0x1000>;
 				interrupts = <27>;
@@ -134,7 +134,7 @@
 			};
 
 			pwm: pwm@10006000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx27-pwm";
 				reg = <0x10006000 0x1000>;
 				interrupts = <23>;
@@ -265,7 +265,7 @@
 				status = "disabled";
 			};
 
-			sdhci1: sdhci@10013000 {
+			sdhci1: mmc@10013000 {
 				compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
 				reg = <0x10013000 0x1000>;
 				interrupts = <11>;
@@ -277,7 +277,7 @@
 				status = "disabled";
 			};
 
-			sdhci2: sdhci@10014000 {
+			sdhci2: mmc@10014000 {
 				compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
 				reg = <0x10014000 0x1000>;
 				interrupts = <10>;
@@ -431,7 +431,7 @@
 				status = "disabled";
 			};
 
-			sdhci3: sdhci@1001e000 {
+			sdhci3: mmc@1001e000 {
 				compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
 				reg = <0x1001e000 0x1000>;
 				interrupts = <9>;
@@ -453,7 +453,7 @@
 			};
 		};
 
-		aipi@10020000 { /* AIPI2 */
+		aipi2: bus@10020000 { /* AIPI2 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -525,7 +525,7 @@
 				reg = <0x10024600 0x200>;
 			};
 
-			sahara2: sahara@10025000 {
+			sahara2: crypto@10025000 {
 				compatible = "fsl,imx27-sahara";
 				reg = <0x10025000 0x1000>;
 				interrupts = <59>;
@@ -534,13 +534,13 @@
 				clock-names = "ipg", "ahb";
 			};
 
-			clks: ccm@10027000{
+			clks: ccm@10027000 {
 				compatible = "fsl,imx27-ccm";
 				reg = <0x10027000 0x1000>;
 				#clock-cells = <1>;
 			};
 
-			iim: iim@10028000 {
+			iim: efuse@10028000 {
 				compatible = "fsl,imx27-iim";
 				reg = <0x10028000 0x1000>;
 				interrupts = <62>;
@@ -558,7 +558,7 @@
 			};
 		};
 
-		nfc: nand@d8000000 {
+		nfc: nand-controller@d8000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "fsl,imx27-nand";
@@ -588,6 +588,9 @@
 		iram: sram@ffff4c00 {
 			compatible = "mmio-sram";
 			reg = <0xffff4c00 0xb400>;
+			ranges = <0 0xffff4c00 0xb400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx31-bug.dts b/arch/arm/boot/dts/nxp/imx/imx31-bug.dts
index d87eee3f9b3c..d87eee3f9b3c 100644
--- a/arch/arm/boot/dts/imx31-bug.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx31-bug.dts
diff --git a/arch/arm/boot/dts/imx31-lite.dts b/arch/arm/boot/dts/nxp/imx/imx31-lite.dts
index d17abdfb6330..d17abdfb6330 100644
--- a/arch/arm/boot/dts/imx31-lite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx31-lite.dts
diff --git a/arch/arm/boot/dts/imx31.dtsi b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
index 6b62f0745b82..e1ae7c175f7d 100644
--- a/arch/arm/boot/dts/imx31.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
@@ -48,7 +48,7 @@
 		reg = <0x68000000 0x100000>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -63,7 +63,7 @@
 			ranges = <0 0x1fffc000 0x4000>;
 		};
 
-		aips@43f00000 { /* AIPS1 */
+		aips1: bus@43f00000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -166,14 +166,14 @@
 			};
 		};
 
-		spba@50000000 {
+		spba-bus@50000000 {
 			compatible = "fsl,spba-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x50000000 0x100000>;
 			ranges;
 
-			sdhci1: sdhci@50004000 {
+			sdhci1: mmc@50004000 {
 				compatible = "fsl,imx31-mmc";
 				reg = <0x50004000 0x4000>;
 				interrupts = <9>;
@@ -184,7 +184,7 @@
 				status = "disabled";
 			};
 
-			sdhci2: sdhci@50008000 {
+			sdhci2: mmc@50008000 {
 				compatible = "fsl,imx31-mmc";
 				reg = <0x50008000 0x4000>;
 				interrupts = <8>;
@@ -217,7 +217,7 @@
 				status = "disabled";
 			};
 
-			iim: iim@5001c000 {
+			iim: efuse@5001c000 {
 				compatible = "fsl,imx31-iim", "fsl,imx27-iim";
 				reg = <0x5001c000 0x1000>;
 				interrupts = <19>;
@@ -225,14 +225,14 @@
 			};
 		};
 
-		aips@53f00000 { /* AIPS2 */
+		bus@53f00000 { /* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x53f00000 0x100000>;
 			ranges;
 
-			clks: ccm@53f80000{
+			clks: ccm@53f80000 {
 				compatible = "fsl,imx31-ccm";
 				reg = <0x53f80000 0x4000>;
 				interrupts = <31>, <53>;
@@ -297,7 +297,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx31-sdma";
 				reg = <0x53fd4000 0x4000>;
 				interrupts = <34>;
@@ -315,10 +315,11 @@
 				clock-names = "ref", "ipg";
 			};
 
-			wdog: wdog@53fdc000 {
+			wdog: watchdog@53fdc000 {
 				compatible = "fsl,imx31-wdt", "fsl,imx21-wdt";
 				reg = <0x53fdc000 0x4000>;
 				clocks = <&clks 41>;
+				interrupts = <55>;
 			};
 
 			pwm: pwm@53fe0000 {
@@ -327,7 +328,7 @@
 				interrupts = <26>;
 				clocks = <&clks 10>, <&clks 42>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 		};
diff --git a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-cpuimx35.dtsi
index 17bd2a97609a..17bd2a97609a 100644
--- a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-cpuimx35.dtsi
diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-mbimxsd35-baseboard.dts
index b1c11170ac25..7f4f812b0811 100644
--- a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-mbimxsd35-baseboard.dts
@@ -13,12 +13,12 @@
 	model = "Eukrea CPUIMX35";
 	compatible = "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_bp1>;
 
-		bp1 {
+		button {
 			label = "BP1";
 			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
diff --git a/arch/arm/boot/dts/imx35-pdk.dts b/arch/arm/boot/dts/nxp/imx/imx35-pdk.dts
index ddce0a844758..ddce0a844758 100644
--- a/arch/arm/boot/dts/imx35-pdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx35-pdk.dts
diff --git a/arch/arm/boot/dts/imx35-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx35-pinfunc.h
index 9d6cc9564b72..9d6cc9564b72 100644
--- a/arch/arm/boot/dts/imx35-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx35-pinfunc.h
diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
index 9cbdc1a15cda..2d20e5541acc 100644
--- a/arch/arm/boot/dts/imx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
@@ -59,14 +59,14 @@
 		interrupt-parent = <&avic>;
 		ranges;
 
-		L2: l2-cache@30000000 {
+		L2: cache-controller@30000000 {
 			compatible = "arm,l210-cache";
 			reg = <0x30000000 0x1000>;
 			cache-unified;
 			cache-level = <2>;
 		};
 
-		aips1: aips@43f00000 {
+		aips1: bus@43f00000 {
 			compatible = "fsl,aips", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -189,7 +189,7 @@
 				status = "disabled";
 			};
 
-			fec: fec@50038000 {
+			fec: ethernet@50038000 {
 				compatible = "fsl,imx35-fec", "fsl,imx27-fec";
 				reg = <0x50038000 0x4000>;
 				clocks = <&clks 46>, <&clks 8>;
@@ -199,7 +199,7 @@
 			};
 		};
 
-		aips2: aips@53f00000 {
+		aips2: bus@53f00000 {
 			compatible = "fsl,aips", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -231,7 +231,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			esdhc1: esdhc@53fb4000 {
+			esdhc1: mmc@53fb4000 {
 				compatible = "fsl,imx35-esdhc";
 				reg = <0x53fb4000 0x4000>;
 				interrupts = <7>;
@@ -240,7 +240,7 @@
 				status = "disabled";
 			};
 
-			esdhc2: esdhc@53fb8000 {
+			esdhc2: mmc@53fb8000 {
 				compatible = "fsl,imx35-esdhc";
 				reg = <0x53fb8000 0x4000>;
 				interrupts = <8>;
@@ -249,7 +249,7 @@
 				status = "disabled";
 			};
 
-			esdhc3: esdhc@53fbc000 {
+			esdhc3: mmc@53fbc000 {
 				compatible = "fsl,imx35-esdhc";
 				reg = <0x53fbc000 0x4000>;
 				interrupts = <9>;
@@ -284,7 +284,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx35-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 9>, <&clks 65>;
@@ -294,11 +294,10 @@
 				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx35.bin";
 			};
 
-			wdog: wdog@53fdc000 {
+			wdog: watchdog@53fdc000 {
 				compatible = "fsl,imx35-wdt", "fsl,imx21-wdt";
 				reg = <0x53fdc000 0x4000>;
 				clocks = <&clks 74>;
-				clock-names = "";
 				interrupts = <55>;
 			};
 
@@ -320,7 +319,7 @@
 				status = "disabled";
 			};
 
-			iim@53ff0000 {
+			efuse@53ff0000 {
 				compatible = "fsl,imx35-iim";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <19>;
diff --git a/arch/arm/boot/dts/imx50-evk.dts b/arch/arm/boot/dts/nxp/imx/imx50-evk.dts
index a25da415cb02..3f45c01d9cce 100644
--- a/arch/arm/boot/dts/imx50-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx50-evk.dts
@@ -20,10 +20,10 @@
 &cspi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_cspi>;
-	cs-gpios = <&gpio4 11 0>, <&gpio4 13 0>;
+	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	flash: m25p32@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p32", "jedec,spi-nor";
@@ -59,7 +59,7 @@
 				MX50_PAD_CSPI_MISO__CSPI_MISO		0x00
 				MX50_PAD_CSPI_MOSI__CSPI_MOSI		0x00
 				MX50_PAD_CSPI_SS0__GPIO4_11		0xc4
-				MX50_PAD_ECSPI1_MOSI__CSPI_SS1		0xf4
+				MX50_PAD_ECSPI1_MOSI__GPIO4_13		0x84
 			>;
 		};
 
diff --git a/arch/arm/boot/dts/imx50-kobo-aura.dts b/arch/arm/boot/dts/nxp/imx/imx50-kobo-aura.dts
index a0eaf869b913..b1a6a9c58ac3 100644
--- a/arch/arm/boot/dts/imx50-kobo-aura.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx50-kobo-aura.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx50.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Kobo Aura (N514)";
@@ -25,7 +26,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds>;
 
-		on {
+		led-on {
 			label = "kobo_aura:orange:on";
 			gpios = <&gpio6 24 GPIO_ACTIVE_LOW>;
 			panic-indicator;
@@ -37,20 +38,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 		};
 
-		hallsensor {
+		event-hallsensor {
 			label = "Hallsensor";
 			gpios = <&gpio5 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESERVED>;
 			linux,input-type = <EV_SW>;
 		};
 
-		frontlight {
+		event-frontlight {
 			label = "Frontlight";
 			gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DISPLAYTOGGLE>;
@@ -72,7 +73,7 @@
 		states = <3300000 0>;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		enable-gpio = <&gpio4 12 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
 		startup-delay-us = <100000>;
 	};
 };
@@ -119,7 +120,14 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	/* TODO: ektf2132 touch controller at 0x15 */
+	touchscreen@15 {
+		reg = <0x15>;
+		compatible = "elan,ektf2132";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ts>;
+		power-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&gpio5 13 IRQ_TYPE_EDGE_FALLING>;
+	};
 };
 
 &i2c2 {
@@ -135,11 +143,25 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	/* TODO: embedded controller at 0x43 */
+	embedded-controller@43 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ec>;
+		compatible = "netronix,ntxec";
+		reg = <0x43>;
+		system-power-controller;
+		interrupts-extended = <&gpio4 11 IRQ_TYPE_EDGE_FALLING>;
+		#pwm-cells = <2>;
+	};
 };
 
 &iomuxc {
-	pinctrl_gpiokeys: gpiokeys {
+	pinctrl_ec: ecgrp {
+		fsl,pins = <
+			MX50_PAD_CSPI_SS0__GPIO4_11		0x0	/* INT */
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeysgrp {
 		fsl,pins = <
 			MX50_PAD_CSPI_MISO__GPIO4_10		0x0
 			MX50_PAD_SD2_D7__GPIO5_15		0x0
@@ -147,34 +169,34 @@
 		>;
 	};
 
-	pinctrl_i2c1: i2c1 {
+	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX50_PAD_I2C1_SCL__I2C1_SCL		0x400001fd
 			MX50_PAD_I2C1_SDA__I2C1_SDA		0x400001fd
 		>;
 	};
 
-	pinctrl_i2c2: i2c2 {
+	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX50_PAD_I2C2_SCL__I2C2_SCL		0x400001fd
 			MX50_PAD_I2C2_SDA__I2C2_SDA		0x400001fd
 		>;
 	};
 
-	pinctrl_i2c3: i2c3 {
+	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
 			MX50_PAD_I2C3_SCL__I2C3_SCL		0x400001fd
 			MX50_PAD_I2C3_SDA__I2C3_SDA		0x400001fd
 		>;
 	};
 
-	pinctrl_leds: leds {
+	pinctrl_leds: ledsgrp {
 		fsl,pins = <
 			MX50_PAD_PWM1__GPIO6_24			0x0
 		>;
 	};
 
-	pinctrl_sd1: sd1 {
+	pinctrl_sd1: sd1grp {
 		fsl,pins = <
 			MX50_PAD_SD1_CMD__ESDHC1_CMD		0x1e4
 			MX50_PAD_SD1_CLK__ESDHC1_CLK		0xd4
@@ -187,7 +209,7 @@
 		>;
 	};
 
-	pinctrl_sd2: sd2 {
+	pinctrl_sd2: sd2grp {
 		fsl,pins = <
 			MX50_PAD_SD2_CMD__ESDHC2_CMD		0x1e4
 			MX50_PAD_SD2_CLK__ESDHC2_CLK		0xd4
@@ -198,19 +220,19 @@
 		>;
 	};
 
-	pinctrl_sd2_reset: sd2-reset {
+	pinctrl_sd2_reset: sd2-resetgrp {
 		fsl,pins = <
 			MX50_PAD_ECSPI2_MOSI__GPIO4_17		0x0
 		>;
 	};
 
-	pinctrl_sd2_vmmc: sd2-vmmc {
+	pinctrl_sd2_vmmc: sd2-vmmcgrp {
 		fsl,pins = <
 			MX50_PAD_ECSPI1_SCLK__GPIO4_12		0x0
 		>;
 	};
 
-	pinctrl_sd3: sd3 {
+	pinctrl_sd3: sd3grp {
 		fsl,pins = <
 			MX50_PAD_SD3_CMD__ESDHC3_CMD		0x1e4
 			MX50_PAD_SD3_CLK__ESDHC3_CLK		0xd4
@@ -225,14 +247,21 @@
 		>;
 	};
 
-	pinctrl_uart2: uart2 {
+	pinctrl_ts: tsgrp {
+		fsl,pins = <
+			MX50_PAD_CSPI_MOSI__GPIO4_9		0x0
+			MX50_PAD_SD2_D5__GPIO5_13		0x0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX50_PAD_UART2_TXD__UART2_TXD_MUX	0x1e4
 			MX50_PAD_UART2_RXD__UART2_RXD_MUX	0x1e4
 		>;
 	};
 
-	pinctrl_usbphy: usbphy {
+	pinctrl_usbphy: usbphygrp {
 		fsl,pins = <
 			MX50_PAD_ECSPI2_SS0__GPIO4_19		0x0
 		>;
diff --git a/arch/arm/boot/dts/imx50-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx50-pinfunc.h
index 5e6b30247543..5e6b30247543 100644
--- a/arch/arm/boot/dts/imx50-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx50-pinfunc.h
diff --git a/arch/arm/boot/dts/imx50.dtsi b/arch/arm/boot/dts/nxp/imx/imx50.dtsi
index 0bfe7c91d0eb..c5b25d2f6264 100644
--- a/arch/arm/boot/dts/imx50.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx50.dtsi
@@ -62,25 +62,25 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <22579200>;
 		};
 
 		ckih2 {
-			compatible = "fsl,imx-ckih2", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -94,28 +94,28 @@
 		status = "okay";
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&tzic>;
 		ranges;
 
-		aips@50000000 { /* AIPS1 */
+		aips1: bus@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x50000000 0x10000000>;
 			ranges;
 
-			spba@50000000 {
+			spba-bus@50000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0x50000000 0x40000>;
 				ranges;
 
-				esdhc1: esdhc@50004000 {
+				esdhc1: mmc@50004000 {
 					compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
 					reg = <0x50004000 0x4000>;
 					interrupts = <1>;
@@ -127,7 +127,7 @@
 					status = "disabled";
 				};
 
-				esdhc2: esdhc@50008000 {
+				esdhc2: mmc@50008000 {
 					compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
 					reg = <0x50008000 0x4000>;
 					interrupts = <2>;
@@ -176,7 +176,7 @@
 					status = "disabled";
 				};
 
-				esdhc3: esdhc@50020000 {
+				esdhc3: mmc@50020000 {
 					compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
 					reg = <0x50020000 0x4000>;
 					interrupts = <3>;
@@ -188,7 +188,7 @@
 					status = "disabled";
 				};
 
-				esdhc4: esdhc@50024000 {
+				esdhc4: mmc@50024000 {
 					compatible = "fsl,imx50-esdhc", "fsl,imx53-esdhc";
 					reg = <0x50024000 0x4000>;
 					interrupts = <4>;
@@ -267,7 +267,7 @@
 					      <&iomuxc 20 140 11>;
 			};
 
-			wdog1: wdog@53f98000 {
+			wdog1: watchdog@53f98000 {
 				compatible = "fsl,imx50-wdt", "fsl,imx21-wdt";
 				reg = <0x53f98000 0x4000>;
 				interrupts = <58>;
@@ -288,13 +288,8 @@
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			gpr: iomuxc-gpr@53fa8000 {
-				compatible = "fsl,imx50-iomuxc-gpr", "syscon";
-				reg = <0x53fa8000 0xc>;
-			};
-
 			pwm1: pwm@53fb4000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx50-pwm", "fsl,imx27-pwm";
 				reg = <0x53fb4000 0x4000>;
 				clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>,
@@ -304,7 +299,7 @@
 			};
 
 			pwm2: pwm@53fb8000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx50-pwm", "fsl,imx27-pwm";
 				reg = <0x53fb8000 0x4000>;
 				clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>,
@@ -333,13 +328,14 @@
 				status = "disabled";
 			};
 
-			src: src@53fd0000 {
+			src: reset-controller@53fd0000 {
 				compatible = "fsl,imx50-src", "fsl,imx51-src";
 				reg = <0x53fd0000 0x4000>;
+				interrupts = <75>;
 				#reset-cells = <1>;
 			};
 
-			clks: ccm@53fd4000{
+			clks: ccm@53fd4000 {
 				compatible = "fsl,imx50-ccm";
 				reg = <0x53fd4000 0x4000>;
 				interrupts = <0 71 0x04 0 72 0x04>;
@@ -389,7 +385,7 @@
 			};
 		};
 
-		aips@60000000 {	/* AIPS2 */
+		aips2: bus@60000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -425,7 +421,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx50-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
diff --git a/arch/arm/boot/dts/imx51-apf51.dts b/arch/arm/boot/dts/nxp/imx/imx51-apf51.dts
index ba28ffe06fe2..ba28ffe06fe2 100644
--- a/arch/arm/boot/dts/imx51-apf51.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-apf51.dts
diff --git a/arch/arm/boot/dts/imx51-apf51dev.dts b/arch/arm/boot/dts/nxp/imx/imx51-apf51dev.dts
index 563c1aae8c0c..b61d55ca1467 100644
--- a/arch/arm/boot/dts/imx51-apf51dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-apf51dev.dts
@@ -63,7 +63,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -74,8 +74,8 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>,
-		   <&gpio4 25 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+		   <&gpio4 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/nxp/imx/imx51-babbage.dts
index ed6a3ce874b2..16ff543f3fbf 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-babbage.dts
@@ -58,29 +58,27 @@
 
 	display1: disp1 {
 		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
 		interface-pix-fmt = "rgb24";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_ipu_disp1>;
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: dvi {
-				clock-frequency = <65000000>;
-				hactive = <1024>;
-				vactive = <768>;
-				hback-porch = <220>;
-				hfront-porch = <40>;
-				vback-porch = <21>;
-				vfront-porch = <7>;
-				hsync-len = <60>;
-				vsync-len = <10>;
-			};
-		};
 
-		port {
+		port@0 {
+		reg = <0>;
+
 			display0_in: endpoint {
 				remote-endpoint = <&ipu_di0_disp1>;
 			};
 		};
+
+		port@1 {
+			reg = <1>;
+
+			parallel_display_out: endpoint {
+				remote-endpoint = <&tfp410_in>;
+			};
+		};
 	};
 
 	display2: disp2 {
@@ -115,12 +113,48 @@
 		};
 	};
 
+	dvi-connector {
+		compatible = "dvi-connector";
+		digital;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+
+	dvi-encoder {
+		compatible = "ti,tfp410";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint {
+					remote-endpoint = <&parallel_display_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_POWER>;
@@ -139,22 +173,15 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_hub_reset: regulator@0 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbotgreg>;
-			reg = <0>;
-			regulator-name = "hub_reset";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_hub_reset: regulator-hub-reset {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotgreg>;
+		regulator-name = "hub_reset";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
diff --git a/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-jsk.dts
index aab8d6f137c3..10cae7c3a879 100644
--- a/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-jsk.dts
@@ -13,6 +13,13 @@
 	chosen {
 		stdout-path = &uart1;
 	};
+
+	usbphy1: usbphy1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
+	};
 };
 
 &esdhc1 {
@@ -63,6 +70,7 @@
 &usbh1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
+	fsl,usbphy = <&usbphy1>;
 	dr_mode = "host";
 	phy_type = "ulpi";
 	disable-over-current;
diff --git a/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi
index 16addb3a2a1b..f0809a16a2ce 100644
--- a/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi
@@ -34,22 +34,22 @@
 
 		regulators {
 			sw1_reg: sw1 {
-				regulator-min-microvolt = <1000000>;
+				regulator-min-microvolt = <1050000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			sw2_reg: sw2 {
-				regulator-min-microvolt = <1225000>;
-				regulator-max-microvolt = <1225000>;
+				regulator-min-microvolt = <1175000>;
+				regulator-max-microvolt = <1275000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			sw3_reg: sw3 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1350000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
@@ -102,18 +102,6 @@
 				regulator-always-on;
 			};
 
-			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-			};
-
-			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <3150000>;
-				regulator-max-microvolt = <3150000>;
-				regulator-always-on;
-			};
-
 			vgen3_reg: vgen3 {
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -124,8 +112,6 @@
 				regulator-always-on;
 			};
 
-			gpo1_reg: gpo1 { };
-
 			gpo2_reg: gpo2 { };
 
 			gpo3_reg: gpo3 { };
@@ -198,6 +184,7 @@
 &usbotg {
 	phy_type = "utmi_wide";
 	disable-over-current;
+	vbus-supply = <&swbst_reg>;
 	/* Device role is not known, keep status disabled */
 };
 
@@ -206,7 +193,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	lan9221: lan9221@5,0 {
+	lan9221: ethernet@5,0 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lan9221>;
 		compatible = "smsc,lan9221", "smsc,lan9115";
diff --git a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-cpuimx51.dtsi
index c2a929ba8ceb..c2a929ba8ceb 100644
--- a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-cpuimx51.dtsi
diff --git a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-mbimxsd51-baseboard.dts
index b6d931e96a8f..aff380e999c7 100644
--- a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-mbimxsd51-baseboard.dts
@@ -45,21 +45,14 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_can: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "CAN_RST";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <20000>;
-			enable-active-high;
-		};
+	reg_can: regulator-can {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN_RST";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <20000>;
+		enable-active-high;
 	};
 
 	sound {
diff --git a/arch/arm/boot/dts/imx51-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx51-pinfunc.h
index 910e0ec50ef3..910e0ec50ef3 100644
--- a/arch/arm/boot/dts/imx51-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx51-pinfunc.h
diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
index 4344632f7940..f7408722d68a 100644
--- a/arch/arm/boot/dts/imx51-ts4800.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
@@ -102,7 +102,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	rtc: m41t00@68 {
+	rtc: rtc@68 {
 		compatible = "st,m41t00";
 		reg = <0x68>;
 	};
@@ -113,6 +113,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm_backlight>;
 	status = "okay";
@@ -173,7 +174,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_interrupt_fpga>;
 			interrupt-parent = <&gpio2>;
-			interrupts= <9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
 		};
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts
index 3596060f52e7..7cd17b43b4b2 100644
--- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts
@@ -119,8 +119,8 @@
 		compatible = "i2c-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_swi2c>;
-		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>, /* sda */
-			<&gpio3 4 GPIO_ACTIVE_HIGH>; /* scl */
+		sda-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <50>;
 		status = "okay";
 
@@ -137,7 +137,7 @@
 		};
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -145,9 +145,9 @@
 		pinctrl-0 = <&pinctrl_gpiospi0>;
 		status = "okay";
 
-		gpio-sck = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio4 12 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 		cs-gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
 
@@ -181,7 +181,7 @@
 
 				port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rev-mii";
 					ethernet = <&fec>;
 
 					fixed-link {
@@ -217,8 +217,8 @@
 		simple-audio-card,widgets =
 			"Headphone", "Headphone Jack";
 		simple-audio-card,routing =
-			"Headphone Jack", "HPLEFT",
-			"Headphone Jack", "HPRIGHT";
+			"Headphone Jack", "TPA6130A2 HPLEFT",
+			"Headphone Jack", "TPA6130A2 HPRIGHT";
 		simple-audio-card,aux-devs = <&hpa1>;
 
 		sound_cpu: simple-audio-card,cpu {
@@ -451,7 +451,7 @@
 			  "", "", "", "",
 			  "", "", "", "";
 
-	unused-sd3-wp-gpio {
+	unused-sd3-wp-hog {
 		/*
 		 * See pinctrl_esdhc1 below for more details on this
 		 */
@@ -470,6 +470,7 @@
 		compatible = "ti,tpa6130a2";
 		reg = <0x60>;
 		Vdd-supply = <&reg_3p3v>;
+		sound-name-prefix = "TPA6130A2";
 	};
 
 	ds1341: rtc@68 {
@@ -555,7 +556,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu1";
 		current-speed = <38400>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu2-mezz.dts
index aa91e5dde4b8..625f9ac671ae 100644
--- a/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu2-mezz.dts
@@ -82,7 +82,7 @@
 
 				port@4 {
 					reg = <4>;
-					label = "cpu";
+					phy-mode = "rev-mii";
 					ethernet = <&fec>;
 
 					fixed-link {
@@ -311,7 +311,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-mezz";
 		current-speed = <57600>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx51-zii-scu3-esb.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu3-esb.dts
index 875b10a7d674..19a3b142c964 100644
--- a/arch/arm/boot/dts/imx51-zii-scu3-esb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu3-esb.dts
@@ -267,7 +267,6 @@
 
 				port@6 {
 					reg = <6>;
-					label = "cpu";
 					phy-mode = "mii";
 					ethernet = <&fec>;
 
@@ -319,7 +318,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-esb";
 		current-speed = <57600>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
index dea86b98e9c3..c96d6311dfa7 100644
--- a/arch/arm/boot/dts/imx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
@@ -48,25 +48,25 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		ckih2 {
-			compatible = "fsl,imx-ckih2", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -104,12 +104,17 @@
 		#phy-cells = <0>;
 	};
 
+	capture-subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu_csi0>, <&ipu_csi1>;
+	};
+
 	display-subsystem {
 		compatible = "fsl,imx-display-subsystem";
 		ports = <&ipu_di0>, <&ipu_di1>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -119,6 +124,9 @@
 		iram: sram@1ffe0000 {
 			compatible = "mmio-sram";
 			reg = <0x1ffe0000 0x20000>;
+			ranges = <0 0x1ffe0000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		gpu: gpu@30000000 {
@@ -143,6 +151,14 @@
 			clock-names = "bus", "di0", "di1";
 			resets = <&src 2>;
 
+			ipu_csi0: port@0 {
+				reg = <0>;
+			};
+
+			ipu_csi1: port@1 {
+				reg = <1>;
+			};
+
 			ipu_di0: port@2 {
 				reg = <2>;
 
@@ -158,21 +174,21 @@
 			};
 		};
 
-		aips@70000000 { /* AIPS1 */
+		aips1: bus@70000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x70000000 0x10000000>;
 			ranges;
 
-			spba@70000000 {
+			spba-bus@70000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0x70000000 0x40000>;
 				ranges;
 
-				esdhc1: esdhc@70004000 {
+				esdhc1: mmc@70004000 {
 					compatible = "fsl,imx51-esdhc";
 					reg = <0x70004000 0x4000>;
 					interrupts = <1>;
@@ -183,7 +199,7 @@
 					status = "disabled";
 				};
 
-				esdhc2: esdhc@70008000 {
+				esdhc2: mmc@70008000 {
 					compatible = "fsl,imx51-esdhc";
 					reg = <0x70008000 0x4000>;
 					interrupts = <2>;
@@ -202,6 +218,8 @@
 					clocks = <&clks IMX5_CLK_UART3_IPG_GATE>,
 						 <&clks IMX5_CLK_UART3_PER_GATE>;
 					clock-names = "ipg", "per";
+					dmas = <&sdma 43 5 1>, <&sdma 44 5 2>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -232,7 +250,7 @@
 					status = "disabled";
 				};
 
-				esdhc3: esdhc@70020000 {
+				esdhc3: mmc@70020000 {
 					compatible = "fsl,imx51-esdhc";
 					reg = <0x70020000 0x4000>;
 					interrupts = <3>;
@@ -244,7 +262,7 @@
 					status = "disabled";
 				};
 
-				esdhc4: esdhc@70024000 {
+				esdhc4: mmc@70024000 {
 					compatible = "fsl,imx51-esdhc";
 					reg = <0x70024000 0x4000>;
 					interrupts = <4>;
@@ -357,14 +375,14 @@
 				status = "disabled";
 			};
 
-			wdog1: wdog@73f98000 {
+			wdog1: watchdog@73f98000 {
 				compatible = "fsl,imx51-wdt", "fsl,imx21-wdt";
 				reg = <0x73f98000 0x4000>;
 				interrupts = <58>;
 				clocks = <&clks IMX5_CLK_DUMMY>;
 			};
 
-			wdog2: wdog@73f9c000 {
+			wdog2: watchdog@73f9c000 {
 				compatible = "fsl,imx51-wdt", "fsl,imx21-wdt";
 				reg = <0x73f9c000 0x4000>;
 				interrupts = <59>;
@@ -387,7 +405,7 @@
 			};
 
 			pwm1: pwm@73fb4000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx51-pwm", "fsl,imx27-pwm";
 				reg = <0x73fb4000 0x4000>;
 				clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>,
@@ -397,7 +415,7 @@
 			};
 
 			pwm2: pwm@73fb8000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx51-pwm", "fsl,imx27-pwm";
 				reg = <0x73fb8000 0x4000>;
 				clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>,
@@ -413,6 +431,8 @@
 				clocks = <&clks IMX5_CLK_UART1_IPG_GATE>,
 					 <&clks IMX5_CLK_UART1_PER_GATE>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 18 4 1>, <&sdma 19 4 2>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -423,16 +443,19 @@
 				clocks = <&clks IMX5_CLK_UART2_IPG_GATE>,
 					 <&clks IMX5_CLK_UART2_PER_GATE>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 16 4 1>, <&sdma 17 4 2>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
-			src: src@73fd0000 {
+			src: reset-controller@73fd0000 {
 				compatible = "fsl,imx51-src";
 				reg = <0x73fd0000 0x4000>;
+				interrupts = <75>;
 				#reset-cells = <1>;
 			};
 
-			clks: ccm@73fd4000{
+			clks: ccm@73fd4000 {
 				compatible = "fsl,imx51-ccm";
 				reg = <0x73fd4000 0x4000>;
 				interrupts = <0 71 0x04 0 72 0x04>;
@@ -440,7 +463,7 @@
 			};
 		};
 
-		aips@80000000 {	/* AIPS2 */
+		aips2: bus@80000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -452,8 +475,8 @@
 				reg = <0x83f00000 0x60>;
 			};
 
-			iim: iim@83f98000 {
-				compatible = "fsl,imx51-iim", "fsl,imx27-iim";
+			iim: efuse@83f98000 {
+				compatible = "fsl,imx51-iim", "fsl,imx27-iim", "syscon";
 				reg = <0x83f98000 0x4000>;
 				interrupts = <69>;
 				clocks = <&clks IMX5_CLK_IIM_GATE>;
@@ -484,7 +507,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@83fb0000 {
+			sdma: dma-controller@83fb0000 {
 				compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
 				reg = <0x83fb0000 0x4000>;
 				interrupts = <6>;
@@ -628,7 +651,7 @@
 			};
 
 			sahara: crypto@83ff8000 {
-				compatible = "fsl,imx53-sahara", "fsl,imx51-sahara";
+				compatible = "fsl,imx53-sahara";
 				reg = <0x83ff8000 0x4000>;
 				interrupts = <19 20>;
 				clocks = <&clks IMX5_CLK_SAHARA_IPG_GATE>,
diff --git a/arch/arm/boot/dts/imx53-ard.dts b/arch/arm/boot/dts/nxp/imx/imx53-ard.dts
index 9a2e1fde7128..165e1b00b721 100644
--- a/arch/arm/boot/dts/imx53-ard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-ard.dts
@@ -24,7 +24,7 @@
 		reg = <0xf4000000 0x3ff0000>;
 		ranges;
 
-		lan9220@f4000000 {
+		ethernet@f4000000 {
 			compatible = "smsc,lan9220", "smsc,lan9115";
 			reg = <0xf4000000 0x2000000>;
 			phy-mode = "mii";
@@ -43,52 +43,45 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio5 10 0>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio5 11 0>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		program {
+		key-program {
 			label = "Program";
 			gpios = <&gpio5 12 0>;
 			linux,code = <KEY_PROGRAM >;
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio5 13 0>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio4 0 0>;
 			linux,code = <KEY_VOLUMEDOWN>;
diff --git a/arch/arm/boot/dts/imx53-cx9020.dts b/arch/arm/boot/dts/nxp/imx/imx53-cx9020.dts
index 0a475c234054..0814f5665a59 100644
--- a/arch/arm/boot/dts/imx53-cx9020.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-cx9020.dts
@@ -22,7 +22,7 @@
 	};
 
 	display-0 {
-		#address-cells =<1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "fsl,imx-parallel-display";
 		interface-pix-fmt = "rgb24";
@@ -59,23 +59,26 @@
 	};
 
 	dvi-converter {
-		#address-cells = <1>;
-		#size-cells = <0>;
 		compatible = "ti,tfp410";
 
-		port@0 {
-			reg = <0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
 
-			tfp410_in: endpoint {
-				remote-endpoint = <&display0_out>;
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint {
+					remote-endpoint = <&display0_out>;
+				};
 			};
-		};
 
-		port@1 {
-			reg = <1>;
+			port@1 {
+				reg = <1>;
 
-			tfp410_out: endpoint {
-				remote-endpoint = <&dvi_connector_in>;
+				tfp410_out: endpoint {
+					remote-endpoint = <&dvi_connector_in>;
+				};
 			};
 		};
 	};
@@ -83,27 +86,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		pwr-r {
+		led-pwr-r {
 			gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		pwr-g {
+		led-pwr-g {
 			gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		pwr-b {
+		led-pwr-b {
 			gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		sd1-b {
+		led-sd1-b {
 			linux,default-trigger = "mmc0";
 			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		sd2-b {
+		led-sd2-b {
 			linux,default-trigger = "mmc1";
 			gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/imx53-kp-ddc.dts b/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
index 0e7f071fd10e..0e7f071fd10e 100644
--- a/arch/arm/boot/dts/imx53-kp-ddc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
diff --git a/arch/arm/boot/dts/imx53-kp-hsc.dts b/arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dts
index 6e3d71baac0f..6e3d71baac0f 100644
--- a/arch/arm/boot/dts/imx53-kp-hsc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dts
diff --git a/arch/arm/boot/dts/imx53-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
index 8b25416a5303..4508f34139a0 100644
--- a/arch/arm/boot/dts/imx53-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
@@ -162,6 +162,14 @@
 	>;
 };
 
+&pwm1 {
+	#pwm-cells = <2>;
+};
+
+&pwm2 {
+	#pwm-cells = <2>;
+};
+
 &uart1 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx53-m53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-m53.dtsi
index fe5e0d308e99..00b8d7ca41a2 100644
--- a/arch/arm/boot/dts/imx53-m53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53.dtsi
@@ -15,28 +15,20 @@
 		      <0xb0000000 0x20000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p2v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P2V";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
+	reg_3p2v: regulator-3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
 
-		reg_backlight: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "lcd-supply";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-supply";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx53-m53evk.dts b/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
index daab56abe94a..c323b4dbe9f0 100644
--- a/arch/arm/boot/dts/imx53-m53evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
@@ -52,41 +52,33 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pin_gpio>;
 
-		user1 {
+		led-user1 {
 			label = "user1";
 			gpios = <&gpio2 8 0>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		user2 {
+		led-user2 {
 			label = "user2";
 			gpios = <&gpio2 9 0>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usbh1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 2 0>;
-		};
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 0>;
+	};
 
-		reg_usb_otg_vbus: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 4 0>;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 4 0>;
 	};
 
 	sound {
@@ -321,6 +313,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dts
index 719ed5ca454a..4d77b6077fc1 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dts
@@ -34,33 +34,59 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user1 {
+		led-user1 {
 			label = "TestLed601";
 			gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
 		};
 
-		user2 {
+		led-user2 {
 			label = "TestLed602";
 			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		eth {
+		led-eth {
 			label = "EthLedYe";
 			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "netdev";
 		};
 	};
 
+	lvds-decoder {
+		compatible = "ti,ds90cf364a", "lvds-decoder";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_decoder_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_decoder_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+
 	panel {
 		compatible = "edt,etm0700g0dh6";
 		pinctrl-0 = <&pinctrl_display_gpio>;
+		pinctrl-names = "default";
 		enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
+				remote-endpoint = <&lvds_decoder_out>;
 			};
 		};
 	};
@@ -76,8 +102,7 @@
 		regulator-name = "vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		gpio = <&gpio1 2 0>;
 	};
 };
 
@@ -104,7 +129,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio2 27 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>, <&gpio2 27 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	spidev@0 {
@@ -388,13 +413,13 @@
 
 		pinctrl_power_button: powerbutgrp {
 			fsl,pins = <
-				MX53_PAD_SD2_DATA2__GPIO1_13		0x1e4
+				MX53_PAD_SD2_DATA0__GPIO1_15		0x1e4
 			>;
 		};
 
 		pinctrl_power_out: poweroutgrp {
 			fsl,pins = <
-				MX53_PAD_SD2_DATA0__GPIO1_15		0x1e4
+				MX53_PAD_SD2_DATA2__GPIO1_13		0x1e4
 			>;
 		};
 
@@ -450,7 +475,7 @@
 			reg = <2>;
 
 			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
+				remote-endpoint = <&lvds_decoder_in>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
index 09eee0dd44c1..6a37616cef1c 100644
--- a/arch/arm/boot/dts/imx53-mba53.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
@@ -38,27 +38,19 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_backlight: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "lcd-supply";
-			gpio = <&gpio2 5 0>;
-			startup-delay-us = <5000>;
-		};
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-supply";
+		gpio = <&gpio2 5 0>;
+		startup-delay-us = <5000>;
+	};
 
-		reg_3p2v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P2V";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
+	reg_3p2v: regulator-3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
 	};
 
 	sound {
@@ -169,6 +161,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
 		VDDA-supply = <&reg_3p2v>;
 		VDDIO-supply = <&reg_3p2v>;
diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx53-pinfunc.h
index 67bd06610fdf..67bd06610fdf 100644
--- a/arch/arm/boot/dts/imx53-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx53-pinfunc.h
diff --git a/arch/arm/boot/dts/imx53-ppd.dts b/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
index 5ff9a179c83c..70c4a4852256 100644
--- a/arch/arm/boot/dts/imx53-ppd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
@@ -70,6 +70,12 @@
 		clock-frequency = <11289600>;
 	};
 
+	achc_24M: achc-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
 	sgtlsound: sound {
 		compatible = "fsl,imx53-cpuvo-sgtl5000",
 			     "fsl,imx-audio-sgtl5000";
@@ -176,15 +182,42 @@
 		power-supply = <&reg_3v3_lcd>;
 	};
 
-	leds {
+	led-controller-1 {
 		compatible = "pwm-leds";
 
-		alarm-brightness {
+		led-1 {
+			label = "alarm-brightness";
 			pwms = <&pwm1 0 100000>;
 			max-brightness = <255>;
 		};
 	};
 
+	led-controller-2 {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_alarmled_pins>;
+
+		led-2 {
+			label = "alarm:red";
+			gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			label = "alarm:yellow";
+			gpios = <&gpio7 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "alarm:blue";
+			gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			label = "alarm:silenced";
+			gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	gpio-poweroff {
 		compatible = "gpio-poweroff";
 		gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>;
@@ -287,16 +320,13 @@
 		    &gpio4 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	spidev0: spi@0 {
-		compatible = "ge,achc";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "ge,achc";
-		reg = <1>;
-		spi-max-frequency = <1000000>;
+	spidev0: spi@1 {
+		compatible = "ge,achc", "nxp,kinetis-k20";
+		reg = <1>, <0>;
+		vdd-supply = <&reg_3v3>;
+		vdda-supply = <&reg_3v3>;
+		clocks = <&achc_24M>;
+		reset-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
 	};
 
 	gpioxra0: gpio@2 {
@@ -458,7 +488,7 @@
 	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -563,7 +593,7 @@
 
 	touchscreen@4b {
 		compatible = "atmel,maxtouch";
-		reset-gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
+		reset-gpio = <&gpio5 19 GPIO_ACTIVE_LOW>;
 		reg = <0x4b>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
@@ -598,12 +628,14 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
@@ -622,6 +654,7 @@
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,dma-info = <24 20>;
 	status = "okay";
 };
 
@@ -641,6 +674,7 @@
 &uart5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart5>;
+	fsl,dma-info = <4096 4>;
 	status = "okay";
 };
 
@@ -909,18 +943,10 @@
 			MX53_PAD_NANDF_CS3__GPIO6_16		0x0
 			/* POWER_AND_BOOT_STATUS_INDICATOR */
 			MX53_PAD_PATA_INTRQ__GPIO7_2		0x1e4
-			/* ACTIVATE_ALARM_LIGHT_RED */
-			MX53_PAD_PATA_DIOR__GPIO7_3		0x0
-			/* ACTIVATE_ALARM_LIGHT_YELLOW */
-			MX53_PAD_PATA_DA_1__GPIO7_7		0x0
-			/* ACTIVATE_ALARM_LIGHT_CYAN */
-			MX53_PAD_PATA_DA_2__GPIO7_8		0x0
 			/* RUNNING_ON_BATTERY_INDICATOR_GREEN */
 			MX53_PAD_GPIO_16__GPIO7_11		0x0
 			/* BATTERY_STATUS_INDICATOR_AMBER */
 			MX53_PAD_GPIO_17__GPIO7_12		0x0
-			/* AUDIO_ALARMS_SILENCED_INDICATOR */
-			MX53_PAD_GPIO_18__GPIO7_13		0x0
 		>;
 	};
 
@@ -1080,4 +1106,17 @@
 			MX53_PAD_KEY_COL4__USBOH3_USBOTG_OC	0x180
 		>;
 	};
+
+	pinctrl_alarmled_pins: qmx6alarmledgrp {
+		fsl,pins = <
+			/* ACTIVATE_ALARM_LIGHT_RED */
+			MX53_PAD_PATA_DIOR__GPIO7_3		0x0
+			/* ACTIVATE_ALARM_LIGHT_YELLOW */
+			MX53_PAD_PATA_DA_1__GPIO7_7		0x0
+			/* ACTIVATE_ALARM_LIGHT_CYAN */
+			MX53_PAD_PATA_DA_2__GPIO7_8		0x0
+			/* AUDIO_ALARMS_SILENCED_INDICATOR */
+			MX53_PAD_GPIO_18__GPIO7_13		0x0
+		>;
+	};
 };
diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-qsb-common.dtsi
index 9b4efcd82636..d80440446473 100644
--- a/arch/arm/boot/dts/imx53-qsb-common.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsb-common.dtsi
@@ -16,6 +16,13 @@
 		      <0xb0000000 0x20000000>;
 	};
 
+	backlight_parallel: backlight-parallel {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+	};
+
 	display0: disp0 {
 		compatible = "fsl,imx-parallel-display";
 		pinctrl-names = "default";
@@ -45,20 +52,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -71,7 +78,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pin_gpio7_7>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio7 7 0>;
 			linux,default-trigger = "heartbeat";
@@ -80,6 +87,10 @@
 
 	panel {
 		compatible = "sii,43wvf1g";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_display_power>;
+		backlight = <&backlight_parallel>;
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
 
 		port {
 			panel_in: endpoint {
@@ -88,29 +99,21 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p2v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P2V";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
+	reg_3p2v: regulator-3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
 
-		reg_usb_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio7 8 0>;
-			enable-active-high;
-		};
+	reg_usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 8 0>;
+		enable-active-high;
 	};
 
 	sound {
@@ -142,6 +145,7 @@
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -201,6 +205,12 @@
 			>;
 		};
 
+		pinctrl_display_power: displaypowergrp {
+			fsl,pins = <
+				MX53_PAD_EIM_D24__GPIO3_24		0x1e4
+			>;
+		};
+
 		pinctrl_esdhc1: esdhc1grp {
 			fsl,pins = <
 				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
@@ -209,6 +219,7 @@
 				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
 				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
 				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+				MX53_PAD_EIM_DA13__GPIO3_13		0xe4
 			>;
 		};
 
@@ -290,6 +301,12 @@
 			>;
 		};
 
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX53_PAD_GPIO_1__PWM2_PWMO		0x5
+			>;
+		};
+
 		pinctrl_vga_sync: vgasync-grp {
 			fsl,pins = <
 				/* VGA_HSYNC, VSYNC with max drive strength */
@@ -365,6 +382,12 @@
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
 &sata {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx53-qsb.dts b/arch/arm/boot/dts/nxp/imx/imx53-qsb.dts
index 6831836bd726..6831836bd726 100644
--- a/arch/arm/boot/dts/imx53-qsb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsb.dts
diff --git a/arch/arm/boot/dts/imx53-qsrb.dts b/arch/arm/boot/dts/nxp/imx/imx53-qsrb.dts
index 1bbf24ad308a..1bbf24ad308a 100644
--- a/arch/arm/boot/dts/imx53-qsrb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsrb.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-lvds.dts b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-lvds.dts
new file mode 100644
index 000000000000..b1c1e7c759b3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-lvds.dts
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx53-sk-imx53-atm0700d4.dtsi"
+
+/ {
+	lvds-decoder {
+		compatible = "ti,sn65lvds94", "lvds-decoder";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_decoder_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_decoder_out: endpoint {
+					remote-endpoint = <&panel_rgb_in>;
+				};
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_lvds0: lvds0grp {
+		/* LVDS pins only have pin mux configuration */
+		fsl,pins = <
+			MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK	0x80000000
+			MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0	0x80000000
+			MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1	0x80000000
+			MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2	0x80000000
+			MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3	0x80000000
+		>;
+	};
+
+	pinctrl_spi_gpio: spigrp {
+		fsl,pins = <
+			MX53_PAD_EIM_A22__GPIO2_16		0x1f4
+			MX53_PAD_EIM_A21__GPIO2_17		0x1f4
+			MX53_PAD_EIM_A16__GPIO2_22		0x1f4
+			MX53_PAD_EIM_A18__GPIO2_20		0x1f4
+		>;
+	};
+};
+
+&ldb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lvds0>;
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		reg = <0>;
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@2 {
+			reg = <2>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_decoder_in>;
+			};
+		};
+	};
+};
+
+&panel_rgb_in {
+	remote-endpoint = <&lvds_decoder_out>;
+};
+
+&spi_ts {
+	pinctrl-0 = <&pinctrl_spi_gpio>;
+	pinctrl-names = "default";
+
+	sck-gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+	miso-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+	mosi-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+};
+
+&touchscreen {
+	interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_BOTH>;
+	pendown-gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-rgb.dts b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-rgb.dts
new file mode 100644
index 000000000000..2559ada7e401
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-rgb.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx53-sk-imx53-atm0700d4.dtsi"
+
+/ {
+	display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-0 = <&pinctrl_rgb24>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_rgb_in>;
+			};
+		};
+	};
+
+};
+
+&iomuxc {
+	pinctrl_rgb24: rgb24grp {
+		fsl,pins = <
+			MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK		0x5
+			MX53_PAD_DI0_PIN15__IPU_DI0_PIN15		0x5
+			MX53_PAD_DI0_PIN2__IPU_DI0_PIN2			0x5
+			MX53_PAD_DI0_PIN3__IPU_DI0_PIN3			0x5
+			MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0		0x5
+			MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1		0x5
+			MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2		0x5
+			MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3		0x5
+			MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4		0x5
+			MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5		0x5
+			MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6		0x5
+			MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7		0x5
+			MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8		0x5
+			MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9		0x5
+			MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10		0x5
+			MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11		0x5
+			MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12		0x5
+			MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13		0x5
+			MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14		0x5
+			MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15		0x5
+			MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16		0x5
+			MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17		0x5
+			MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18		0x5
+			MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19		0x5
+			MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20		0x5
+			MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21		0x5
+			MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22		0x5
+			MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23		0x5
+		>;
+	};
+
+	pinctrl_spi_gpio: spigrp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA1__GPIO1_17		0x1f4
+			MX53_PAD_GPIO_7__GPIO1_7		0x1f4
+			MX53_PAD_PATA_DATA3__GPIO2_3		0x1f4
+			MX53_PAD_PATA_DATA8__GPIO2_8		0x1f4
+		>;
+	};
+};
+
+&ipu_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&panel {
+	enable-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+};
+
+&panel_rgb_in {
+	remote-endpoint = <&display_out>;
+};
+
+&pwm1 {
+	status = "disabled";
+};
+
+&spi_ts {
+	pinctrl-0 = <&pinctrl_spi_gpio>;
+	pinctrl-names = "default";
+
+	sck-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+	mosi-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	miso-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
+};
+
+&touchscreen {
+	interrupts-extended = <&gpio2 6 IRQ_TYPE_EDGE_BOTH>;
+	pendown-gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4.dtsi
new file mode 100644
index 000000000000..e395004e80e6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx53-sk-imx53.dts"
+
+/ {
+	panel: panel-rgb {
+		compatible = "powertip,ph800480t013-idf02";
+
+		port {
+			panel_rgb_in: endpoint {
+			};
+		};
+	};
+
+	spi_ts: spi {
+		compatible = "spi-gpio";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		num-chipselects = <1>;
+
+		touchscreen: touchscreen@0 {
+			reg = <0>;
+			compatible = "ti,ads7843";
+			spi-max-frequency = <300000>;
+
+			ti,vref-mv = /bits/ 16 <3300>;
+			ti,x-plate-ohms = /bits/ 16 <450>;
+			ti,y-plate-ohms = /bits/ 16 <250>;
+			ti,debounce-tol = /bits/ 16 <10>;
+			ti,debounce-rep = /bits/ 16 <0>;
+			touchscreen-size-x = <4096>;
+			touchscreen-size-y = <4096>;
+			touchscreen-swapped-x-y;
+			touchscreen-max-pressure = <100>;
+
+			wakeup-source;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53.dts b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53.dts
new file mode 100644
index 000000000000..1a00d290092a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53.dts
@@ -0,0 +1,367 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include "imx53.dtsi"
+
+/ {
+	model = "StarterKit SK-iMX53 Board";
+	compatible = "starterkit,sk-imx53", "fsl,imx53";
+
+	aliases {
+		/*
+		 * iMX RTC is not battery powered on this board.
+		 * Use the i2c RTC as rtc0.
+		 */
+		rtc0 = &rtc;
+		rtc1 = &srtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@70000000 {
+		device_type = "memory";
+		/* v2 had only 256 MB, v3 has 512 MB */
+		reg = <0x70000000 0x20000000>;
+	};
+
+	reg_usb1_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&cpu0 {
+	/* CPU rated to 800 MHz, not the default 1.2GHz. */
+	operating-points = <
+		/* kHz   uV */
+		166666  850000
+		400000  900000
+		800000  1050000
+	>;
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&esdhc1 {
+	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+	mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	tlv320aic23: codec@1a {
+		compatible = "ti,tlv320aic23";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_codec>;
+		#sound-dai-cells = <0>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1338";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX53_PAD_SD2_DATA3__AUDMUX_AUD4_TXC	0x1e4
+			MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD	0x1e4
+			MX53_PAD_SD2_DATA1__AUDMUX_AUD4_TXFS	0x1e4
+			MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD	0x1e4
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_INTRQ__CAN1_TXCAN		0x1e4
+			MX53_PAD_PATA_DIOR__CAN1_RXCAN		0x1e4
+		>;
+	};
+
+	pinctrl_codec: codecgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x1c4
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D16__ECSPI1_SCLK		0x1e4
+			MX53_PAD_EIM_D17__ECSPI1_MISO		0x1e4
+			MX53_PAD_EIM_D18__ECSPI1_MOSI		0x1e4
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT9__ECSPI2_MOSI		0x1e4
+			MX53_PAD_CSI0_DAT10__ECSPI2_MISO	0x1e4
+			MX53_PAD_EIM_CS0__ECSPI2_SCLK		0x1e4
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+			MX53_PAD_EIM_DA14__GPIO3_14		0x1f0
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x1e4
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x1e4
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x1e4
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x1e4
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x1e4
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x1e4
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x1e4
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x1c4
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x1e4
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x1e4
+			MX53_PAD_GPIO_1__GPIO1_1		0x1c4
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
+			MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__I2C2_SDA             0x400001e4
+			MX53_PAD_EIM_EB2__I2C2_SCL		0x400001e4
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__GPIO4_13		0x1e4
+			MX53_PAD_EIM_EB2__GPIO2_30		0x1e4
+		>;
+	};
+
+	pinctrl_nand: nandgrp {
+		fsl,pins = <
+			MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
+			MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
+			MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
+			MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
+			MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
+			MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
+			MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
+			MX53_PAD_NANDF_CS1__EMI_NANDF_CS_1	0x4
+			MX53_PAD_NANDF_CS2__EMI_NANDF_CS_2	0x4
+			MX53_PAD_NANDF_CS3__EMI_NANDF_CS_3	0x4
+			MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0	0xa4
+			MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1	0xa4
+			MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2	0xa4
+			MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3	0xa4
+			MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4	0xa4
+			MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5	0xa4
+			MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6	0xa4
+			MX53_PAD_EIM_DA7__EMI_NAND_WEIM_DA_7	0xa4
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_9__PWM1_PWMO		0x5
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D24__UART3_TXD_MUX		0x1e4
+			MX53_PAD_EIM_D25__UART3_RXD_MUX		0x1e4
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL0__UART4_TXD_MUX	0x1e4
+			MX53_PAD_KEY_ROW0__UART4_RXD_MUX	0x1e4
+		>;
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand>;
+	nand-bus-width = <8>;
+	status = "okay";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x00100000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "u-boot";
+			reg = <0x00100000 0x00100000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x00200000 0x00100000>;
+			read-only;
+		};
+
+		partition@1000000 {
+			label = "kernel-safe";
+			reg = <0x01000000 0x00a00000>;
+			read-only;
+		};
+
+		partition@1a00000 {
+			label = "kernel";
+			reg = <0x01a00000 0x005e0000>;
+		};
+
+		partition@2000000 {
+			label = "ubifs";
+			reg = <0x02000000 0x0e000000>;
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	phy_type = "utmi";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "peripheral";
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/nxp/imx/imx53-smd.dts
index ec9fb8940ffa..55435dfdff8a 100644
--- a/arch/arm/boot/dts/imx53-smd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-smd.dts
@@ -19,13 +19,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio2 14 0>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio2 15 0>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -58,7 +58,7 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	zigbee: mc1323@0 {
@@ -67,10 +67,10 @@
 		reg = <0>;
 	};
 
-	flash: m25p32@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "st,m25p32", "st,m25p", "jedec,spi-nor";
+		compatible = "st,m25p32", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <1>;
 
diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
index ea90fd95ad01..294811bfc8d2 100644
--- a/arch/arm/boot/dts/imx53-tqma53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
@@ -15,19 +15,12 @@
 		reg = <0x70000000 0x40000000>; /* Up to 1GiB */
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 };
 
@@ -50,8 +43,8 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>,
-		   <&gpio3 24 0>, <&gpio3 25 0>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>,
+		   <&gpio3 24 GPIO_ACTIVE_LOW>, <&gpio3 25 GPIO_ACTIVE_LOW>;
 	status = "disabled";
 };
 
@@ -209,6 +202,14 @@
 	};
 };
 
+&pwm1 {
+	#pwm-cells = <2>;
+};
+
+&pwm2 {
+	#pwm-cells = <2>;
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -243,8 +244,8 @@
 &cspi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_cspi>;
-	cs-gpios = <&gpio1 18 0>, <&gpio1 19 0>,
-		   <&gpio1 21 0>;
+	cs-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>, <&gpio1 19 GPIO_ACTIVE_LOW>,
+		   <&gpio1 21 GPIO_ACTIVE_LOW>;
 	status = "disabled";
 };
 
@@ -266,7 +267,7 @@
 		reg = <0x48>;
 	};
 
-	eeprom: 24c64@50 {
+	eeprom: eeprom@50 {
 		compatible = "atmel,24c64";
 		pagesize = <32>;
 		reg = <0x50>;
diff --git a/arch/arm/boot/dts/imx53-tx53-x03x.dts b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x03x.dts
index a7f77527269d..a7f77527269d 100644
--- a/arch/arm/boot/dts/imx53-tx53-x03x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x03x.dts
diff --git a/arch/arm/boot/dts/imx53-tx53-x13x.dts b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x13x.dts
index 6cdf2082c742..6cdf2082c742 100644
--- a/arch/arm/boot/dts/imx53-tx53-x13x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x13x.dts
diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-tx53.dtsi
index 4ab135906949..a439a47fb65a 100644
--- a/arch/arm/boot/dts/imx53-tx53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tx53.dtsi
@@ -81,7 +81,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_key>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <116>; /* KEY_POWER */
@@ -94,7 +94,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_stk5led>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -192,17 +192,6 @@
 		&gpio3 19 GPIO_ACTIVE_HIGH
 	>;
 
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <54000000>;
-	};
 };
 
 &esdhc1 {
@@ -252,7 +241,7 @@
 	clock-frequency = <400000>;
 	status = "okay";
 
-	rtc1: ds1339@68 {
+	rtc1: rtc@68 {
 		compatible = "dallas,ds1339";
 		reg = <0x68>;
 		pinctrl-names = "default";
@@ -542,7 +531,6 @@
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
-	#pwm-cells = <3>;
 };
 
 &sdma {
diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/nxp/imx/imx53-usbarmory.dts
index f34993a490ee..acc44010d510 100644
--- a/arch/arm/boot/dts/imx53-usbarmory.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-usbarmory.dts
@@ -67,7 +67,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "LED";
 			gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/imx53-voipac-bsb.dts b/arch/arm/boot/dts/nxp/imx/imx53-voipac-bsb.dts
index ae53d178a683..ae53d178a683 100644
--- a/arch/arm/boot/dts/imx53-voipac-bsb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-voipac-bsb.dts
diff --git a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-voipac-dmm-668.dtsi
index 289feab42b88..c0622cf7188c 100644
--- a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-voipac-dmm-668.dtsi
@@ -15,29 +15,21 @@
 		      <0xb0000000 0x20000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 31 0>; /* PEN */
-			enable-active-high;
-		};
+	reg_usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 31 0>; /* PEN */
+		enable-active-high;
 	};
 };
 
@@ -119,7 +111,8 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>, <&gpio2 16 0>, <&gpio2 17 0>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>,
+		   <&gpio2 16 GPIO_ACTIVE_LOW>, <&gpio2 17 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53.dtsi
index ed341cfd9d09..07658e477095 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53.dtsi
@@ -86,25 +86,25 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <22579200>;
 		};
 
 		ckih2 {
-			compatible = "fsl,imx-ckih2", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -132,7 +132,7 @@
 		status = "okay";
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -222,21 +222,21 @@
 			clock-names = "core_clk", "mem_iface_clk";
 		};
 
-		aips@50000000 { /* AIPS1 */
+		aips1: bus@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x50000000 0x10000000>;
 			ranges;
 
-			spba@50000000 {
+			spba-bus@50000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0x50000000 0x40000>;
 				ranges;
 
-				esdhc1: esdhc@50004000 {
+				esdhc1: mmc@50004000 {
 					compatible = "fsl,imx53-esdhc";
 					reg = <0x50004000 0x4000>;
 					interrupts = <1>;
@@ -248,7 +248,7 @@
 					status = "disabled";
 				};
 
-				esdhc2: esdhc@50008000 {
+				esdhc2: mmc@50008000 {
 					compatible = "fsl,imx53-esdhc";
 					reg = <0x50008000 0x4000>;
 					interrupts = <2>;
@@ -275,7 +275,7 @@
 				ecspi1: spi@50010000 {
 					#address-cells = <1>;
 					#size-cells = <0>;
-					compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi";
+					compatible = "fsl,imx53-ecspi";
 					reg = <0x50010000 0x4000>;
 					interrupts = <36>;
 					clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>,
@@ -301,7 +301,7 @@
 					status = "disabled";
 				};
 
-				esdhc3: esdhc@50020000 {
+				esdhc3: mmc@50020000 {
 					compatible = "fsl,imx53-esdhc";
 					reg = <0x50020000 0x4000>;
 					interrupts = <3>;
@@ -313,7 +313,7 @@
 					status = "disabled";
 				};
 
-				esdhc4: esdhc@50024000 {
+				esdhc4: mmc@50024000 {
 					compatible = "fsl,imx53-esdhc";
 					reg = <0x50024000 0x4000>;
 					interrupts = <4>;
@@ -427,14 +427,14 @@
 				status = "disabled";
 			};
 
-			wdog1: wdog@53f98000 {
+			wdog1: watchdog@53f98000 {
 				compatible = "fsl,imx53-wdt", "fsl,imx21-wdt";
 				reg = <0x53f98000 0x4000>;
 				interrupts = <58>;
 				clocks = <&clks IMX5_CLK_DUMMY>;
 			};
 
-			wdog2: wdog@53f9c000 {
+			wdog2: watchdog@53f9c000 {
 				compatible = "fsl,imx53-wdt", "fsl,imx21-wdt";
 				reg = <0x53f9c000 0x4000>;
 				interrupts = <59>;
@@ -525,7 +525,7 @@
 			};
 
 			pwm1: pwm@53fb4000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx53-pwm", "fsl,imx27-pwm";
 				reg = <0x53fb4000 0x4000>;
 				clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>,
@@ -535,7 +535,7 @@
 			};
 
 			pwm2: pwm@53fb8000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx53-pwm", "fsl,imx27-pwm";
 				reg = <0x53fb8000 0x4000>;
 				clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>,
@@ -588,13 +588,14 @@
 				status = "disabled";
 			};
 
-			src: src@53fd0000 {
+			src: reset-controller@53fd0000 {
 				compatible = "fsl,imx53-src", "fsl,imx51-src";
 				reg = <0x53fd0000 0x4000>;
+				interrupts = <75>;
 				#reset-cells = <1>;
 			};
 
-			clks: ccm@53fd4000{
+			clks: ccm@53fd4000 {
 				compatible = "fsl,imx53-ccm";
 				reg = <0x53fd4000 0x4000>;
 				interrupts = <0 71 0x04 0 72 0x04>;
@@ -654,7 +655,7 @@
 			};
 		};
 
-		aips@60000000 {	/* AIPS2 */
+		aips2: bus@60000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -666,8 +667,8 @@
 				reg = <0x63f00000 0x60>;
 			};
 
-			iim: iim@63f98000 {
-				compatible = "fsl,imx53-iim", "fsl,imx27-iim";
+			iim: efuse@63f98000 {
+				compatible = "fsl,imx53-iim", "fsl,imx27-iim", "syscon";
 				reg = <0x63f98000 0x4000>;
 				interrupts = <69>;
 				clocks = <&clks IMX5_CLK_IIM_GATE>;
@@ -700,7 +701,7 @@
 			ecspi2: spi@63fac000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi";
+				compatible = "fsl,imx53-ecspi";
 				reg = <0x63fac000 0x4000>;
 				interrupts = <37>;
 				clocks = <&clks IMX5_CLK_ECSPI2_IPG_GATE>,
@@ -709,7 +710,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
@@ -849,6 +850,9 @@
 		ocram: sram@f8000000 {
 			compatible = "mmio-sram";
 			reg = <0xf8000000 0x20000>;
+			ranges = <0 0xf8000000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX5_CLK_OCRAM>;
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-baseboard.dtsi
index 9e027b9a5f91..d477a937b47a 100644
--- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-baseboard.dtsi
@@ -6,7 +6,7 @@
 	keyboard {
 		compatible = "gpio-keys";
 
-		btn0 {
+		button-0 {
 			gpios = <&pcf8575 0 GPIO_ACTIVE_LOW>;
 			label = "btn0";
 			linux,code = <KEY_WAKEUP>;
@@ -14,7 +14,7 @@
 			wakeup-source;
 		};
 
-		btn1 {
+		button-1 {
 			gpios = <&pcf8575 1 GPIO_ACTIVE_LOW>;
 			label = "btn1";
 			linux,code = <KEY_WAKEUP>;
@@ -22,7 +22,7 @@
 			wakeup-source;
 		};
 
-		btn2 {
+		button-2 {
 			gpios = <&pcf8575 2 GPIO_ACTIVE_LOW>;
 			label = "btn2";
 			linux,code = <KEY_WAKEUP>;
@@ -30,7 +30,7 @@
 			wakeup-source;
 		};
 
-		btn3 {
+		button-3 {
 			gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
 			label = "btn3";
 			linux,code = <KEY_WAKEUP>;
@@ -212,6 +212,7 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
 	status = "disabled";
 };
 
@@ -237,7 +238,6 @@
 		compatible = "wlf,wm8962";
 		reg = <0x1a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
-		clock-names = "xclk";
 		DCVDD-supply = <&reg_audio>;
 		DBVDD-supply = <&reg_audio>;
 		AVDD-supply = <&reg_audio>;
@@ -383,7 +383,7 @@
 			MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK	0x100b1
 			MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI	0x100b1
 			MX6QDL_PAD_KEY_COL1__ECSPI1_MISO	0x100b1
-			MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0		0x100b1
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x1b0b0
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6-logicpd-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-som.dtsi
index 547fb141ec0c..547fb141ec0c 100644
--- a/arch/arm/boot/dts/imx6-logicpd-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-som.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dts
new file mode 100644
index 000000000000..4989e8d069a1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dts
@@ -0,0 +1,578 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Altesco I6P Board";
+	compatible = "alt,alti6p", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	clock_ksz8081: clock-ksz8081 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	i2c2-mux {
+		compatible = "i2c-mux";
+		i2c-parent = <&i2c2>;
+		mux-controls = <&i2c_mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c4-mux {
+		compatible = "i2c-mux";
+		i2c-parent = <&i2c4>;
+		mux-controls = <&i2c_mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-debug0 {
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-debug1 {
+			function = LED_FUNCTION_SD;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+
+	i2c_mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2cmux>;
+
+		mux-gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>,
+			    <&gpio5 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_h1_vbus: regulator-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "h1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0		       IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&clock_ksz8081>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "SD1_CD", "", "USB_H1_OC", "", "", "", "",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "", "USB_EXT1_OC", "USB_EXT1_PWR", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ETH_RESET", "", "", "BUZZER", "ETH_INTRP", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "I2C_EN13", "I2C_EN24", "", "", "", "",
+		"", "", "", "", "", "AUDIO_RESET", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	ddc-i2c-bus = <&i2c1>;
+	status = "okay";
+};
+
+/* DDC */
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c2 {
+	clock-frequency = <50000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	/* external interface, device are configured from user space */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <50000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&ssi1 {
+	#sound-dai-cells = <0>;
+	fsl,mode = "ac97-slave";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_h1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_hdmi: hdmigrp {
+		fsl,pins = <
+			/* NOTE: DDC is done via I2C2, so DON'T configure DDC
+			 * pins for HDMI!
+			 */
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE		0x1f8b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL			0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__I2C4_SDA			0x4001f8b1
+			MX6QDL_PAD_NANDF_WP_B__I2C4_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2cmux: i2cmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10		0x1b0b0
+			MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11		0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x8
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__USB_H1_OC			0x1B058
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1B058
+
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-apf6dev.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-apf6dev.dts
index 3dcce3454b08..3dcce3454b08 100644
--- a/arch/arm/boot/dts/imx6dl-apf6dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-apf6dev.dts
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_4.dts
index b16603f27dce..dfa6f64d43cc 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_4.dts
@@ -46,7 +46,7 @@
 
 / {
 	model = "aristainetos2 i.MX6 Dual Lite Board 4";
-	compatible = "fsl,imx6dl";
+	compatible = "abb,aristainetos2-imx6dl-4", "fsl,imx6dl";
 
 	memory@10000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_7.dts
index abb2a1b9ce08..5e15212eaf3a 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_7.dts
@@ -46,7 +46,7 @@
 
 / {
 	model = "aristainetos2 i.MX6 Dual Lite Board 7";
-	compatible = "fsl,imx6dl";
+	compatible = "abb,aristainetos2-imx6dl-7", "fsl,imx6dl";
 
 	memory@10000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
index 37f80ab8ccd0..cc861a43eb58 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "aristainetos i.MX6 Dual Lite Board 4";
-	compatible = "fsl,imx6dl";
+	compatible = "abb,aristainetos-imx6dl-4", "fsl,imx6dl";
 
 	backlight {
 		compatible = "pwm-backlight";
@@ -61,7 +61,7 @@
 };
 
 &ecspi2 {
-	cs-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
@@ -79,5 +79,6 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
index 8d8c8c27e482..b6cb78870cd5 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "aristainetos i.MX6 Dual Lite Board 7";
-	compatible = "fsl,imx6dl";
+	compatible = "abb,aristainetos-imx6dl-7", "fsl,imx6dl";
 
 	memory@10000000 {
 		device_type = "memory";
@@ -69,5 +69,6 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b105pv2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b105pv2.dts
new file mode 100644
index 000000000000..63cdf24eb397
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b105pv2.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B105Pv2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5pv2.dtsi"
+
+/ {
+	model = "General Electric B105Pv2";
+	compatible = "ge,imx6dl-b105pv2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g101evn010";
+	};
+};
+
+&i2c3 {
+	touchscreen@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b105v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b105v2.dts
new file mode 100644
index 000000000000..2e75d700efdb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b105v2.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B105v2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5v2.dtsi"
+
+/ {
+	model = "General Electric B105v2";
+	compatible = "ge,imx6dl-b105v2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g101evn010";
+	};
+};
+
+&i2c3 {
+	touchscreen@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b125pv2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b125pv2.dts
new file mode 100644
index 000000000000..94625d5d5918
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b125pv2.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B125Pv2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5pv2.dtsi"
+
+/ {
+	model = "General Electric B125Pv2";
+	compatible = "ge,imx6dl-b125pv2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g121ean01";
+	};
+};
+
+&i2c3 {
+	touchscreen@2a {
+		compatible = "eeti,exc80h60";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b125v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b125v2.dts
new file mode 100644
index 000000000000..b3cfa8110ade
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b125v2.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B125v2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5v2.dtsi"
+
+/ {
+	model = "General Electric B125v2";
+	compatible = "ge,imx6dl-b125v2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g121ean01";
+	};
+};
+
+&i2c3 {
+	touchscreen@2a {
+		compatible = "eeti,exc80h60";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b155v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b155v2.dts
new file mode 100644
index 000000000000..7edc788bcb8f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b155v2.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B155v2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5v2.dtsi"
+
+/ {
+	model = "General Electric B155v2";
+	compatible = "ge,imx6dl-b155v2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g156xtn01";
+	};
+};
+
+&i2c3 {
+	touchscreen@2a {
+		compatible = "eeti,exc80h84";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5pv2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5pv2.dtsi
new file mode 100644
index 000000000000..9f1655540cb9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5pv2.dtsi
@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B1x5Pv2
+// patient monitor series
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+#include <dt-bindings/input/input.h>
+#include "imx6dl-qmx6.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	/* Do not allow frequencies above 800MHz */
+	cpus {
+		cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				792000  1175000
+				396000  1150000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz	SOC-PU uV */
+				792000	1175000
+				396000	1175000
+			>;
+		};
+
+		cpu@1 {
+			operating-points = <
+				/* kHz    uV */
+				792000  1175000
+				396000  1150000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz	SOC-PU uV */
+				792000	1175000
+				396000	1175000
+			>;
+		};
+	};
+
+	reg_syspwr: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "SYS_PWR";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	reg_5v_pmc: regulator-5v-pmc {
+		compatible = "regulator-fixed";
+		regulator-name = "5V PMC";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_syspwr>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_syspwr>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_syspwr>;
+	};
+
+	reg_5v0_audio: regulator-5v0-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "5V0_AUDIO";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+		gpio = <&tca6424a 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * This must be always-on for da7212, which has some not
+		 * properly documented dependencies for it's speaker supply
+		 * pin. The issue manifests as speaker volume being very low.
+		 */
+		regulator-always-on;
+	};
+
+
+	reg_3v3_audio: regulator-3v3-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_3v3>;
+		pinctrl-0 = <&pinctrl_q7_hda_reset>;
+		pinctrl-names = "default";
+		gpio = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_2v5_audio: regulator-2v5-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "2V5_AUDIO";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&reg_3v3_audio>;
+
+	};
+
+	reg_wlan: regulator-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WLAN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_3v3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_sdio_power>;
+		gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <70000>;
+	};
+
+	reg_bl: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "LED_VCC";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&reg_syspwr>;
+		pinctrl-0 = <&pinctrl_q7_lcd_power>;
+		pinctrl-names = "default";
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+	};
+
+	usb_power: regulator-usb-power {
+		compatible = "regulator-fixed";
+		regulator-name = "USB POWER";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+	};
+
+	charger: battery-charger {
+		compatible = "gpio-charger"; /* ti,bq24172 */
+		charger-type = "mains";
+		gpios = <&tca6424a 3 GPIO_ACTIVE_LOW>;
+		charge-current-limit-gpios = <&tca6424a 11 GPIO_ACTIVE_HIGH>,
+					     <&tca6424a 12 GPIO_ACTIVE_HIGH>;
+		charge-current-limit-mapping = <1300000 0x0>,
+					       <700000 0x1>,
+					       <0 0x2>;
+		charge-status-gpios = <&tca6424a 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_spi_cs1>;
+		gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+	};
+
+	power-button-key {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_sleep_button>;
+
+		power-button {
+			label = "power button";
+			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+	};
+
+	rotary-encoder-key {
+		compatible = "gpio-keys";
+
+		rotary-encoder-event {
+			label = "rotary-encoder press";
+			gpios = <&tca6424a 0 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_ENTER>;
+			linux,can-disable;
+		};
+	};
+
+	rotary-encoder {
+		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio2 &pinctrl_q7_gpio4>;
+		gpios = <&gpio4 26 GPIO_ACTIVE_LOW>, <&gpio1 0 GPIO_ACTIVE_LOW>;
+		rotary-encoder,relative-axis;
+		rotary-encoder,steps-per-period = <2>;
+		wakeup-source;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio1 &pinctrl_q7_gpio3 &pinctrl_q7_gpio5>;
+
+		led-alarm1 {
+			label = "alarm:red";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-alarm2 {
+			label = "alarm:yellow";
+			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-alarm3 {
+			label = "alarm:blue";
+			gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_backlight_enable>;
+		power-supply = <&reg_bl>;
+		pwms = <&pwm4 0 5000000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <179>;
+		enable-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	};
+
+	panel {
+		backlight = <&backlight>;
+		power-supply = <&reg_lcd>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,widgets = "Speaker", "Ext Spk";
+		simple-audio-card,routing = "Ext Spk", "LINE";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12288000>;
+	};
+};
+
+&audmux {
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	battery: battery@b {
+		compatible = "ti,bq20z65", "sbs,sbs-battery";
+		reg = <0x0b>;
+		sbs,battery-detect-gpios = <&tca6424a 5 GPIO_ACTIVE_LOW>;
+		sbs,i2c-retry-count = <5>;
+		power-supplies = <&charger>;
+	};
+
+	codec: audio-codec@1a {
+		compatible = "dlg,da7212";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_2v5_audio>;
+		VDDSP-supply = <&reg_5v0_audio>;
+		VDDMIC-supply = <&reg_3v3_audio>;
+		VDDIO-supply = <&reg_3v3_audio>;
+		clocks = <&clk_ext_audio_codec>;
+		clock-names = "mclk";
+	};
+};
+
+&i2c5 {
+	tca6424a: gpio-controller@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio6>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-line-names = "GPIO_ROTOR#", "ACM_IO_INT", "TMP_SENSOR_IRQ", "AC_IN",
+				  "TF_S", "BATT_T", "LED_INC_CHAR", "ACM1_OCF",
+				  "ACM2_OCF", "ACM_IO_RST", "USB1_POWER_EN", "EGPIO_CC_CTL0",
+				  "EGPIO_CC_CTL1", "12V_OEMNBP_EN", "CP2105_RST", "",
+				  "SPEAKER_PA_EN", "ARM7_UPI_RESET", "ARM7_PWR_RST", "NURSE_CALL",
+				  "MARKER_EN", "EGPIO_TOUCH_RST", "PRESSURE_INT1", "PRESSURE_INT2";
+
+	};
+
+	tmp75: temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+		vs-supply = <&reg_3v3>;
+		interrupt-parent = <&tca6424a>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		status = "okay";
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&ssi1 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&usb_power>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+
+	/*
+	 * TPS2051BDGN fault-gpio is connected to Q7[86] USB_0_1_OC_N.
+	 * On QMX6 this is not connceted to the i.MX6, but to the USB Hub
+	 * from &usbh1. This means, that we cannot easily detect and handle
+	 * over-current events. Fortunately the regulator limits the current
+	 * automatically, so the hardware is still protected.
+	 */
+};
+
+&usdhc4 {
+	/* WiFi module */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	wakeup-source;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	max-frequency = <25000000>;
+	vmmc-supply = <&reg_wlan>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio7>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
+
+		tcxo-clock-frequency = <26000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5v2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5v2.dtsi
new file mode 100644
index 000000000000..590dcc0953cc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5v2.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for General Electric B1x5v2
+// patient monitor series
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+#include <dt-bindings/input/input.h>
+#include "imx6dl-b1x5pv2.dtsi"
+
+/ {
+	reg_3v3_acm: regulator-3v3-acm {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3 ACM";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_3v3>;
+	};
+};
+
+&i2c1 {
+	tca6416: gpio-controller@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		reset-gpios = <&tca6424a 9 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&reg_3v3_acm>;
+		gpio-line-names = "ACM1_EN", "ACM1_CL0", "ACM1_CL1", "ACM1_CL2",
+				  "", "ACM2_EN", "ACM2_CL0", "ACM2_CL1",
+				  "ACM2_CL2", "", "", "",
+				  "", "", "", "";
+
+		/*
+		 * The interrupt pin is connected to &tca6424a pin 1, but the Linux
+		 * TCA6424 driver cannot handle low type interrupts at the moment
+		 * (and support cannot be added without some ugly hacks). Since this
+		 * controller does not have any input type GPIOs, just pretend
+		 * that the interrupt pin is unconnected.
+		 */
+	};
+};
+
+&i2c5 {
+	mpl3115a2: pressure-sensor@60 {
+		compatible = "fsl,mpl3115";
+		reg = <0x60>;
+
+		/*
+		 * The MPL3115 interrupts are connected to pin 22 and 23
+		 * of &tca6424a, but the binding does not yet support
+		 * interrupts.
+		 */
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-aster.dts
new file mode 100644
index 000000000000..82a0d1a28d12
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-aster.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Aster Board";
+	compatible = "toradex,colibri_imx6dl-aster", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	cs-gpios = <
+		&gpio5 2 GPIO_ACTIVE_HIGH
+		&gpio5 4 GPIO_ACTIVE_HIGH
+	>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4 &pinctrl_csi_gpio_2>;
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c3 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_csi_gpio_1
+		&pinctrl_gpio_2
+		&pinctrl_gpio_aster
+		&pinctrl_usbh_oc_1
+		&pinctrl_usbc_id_1
+		&pinctrl_weim_gpio_5
+	>;
+
+	pinctrl_gpio_aster: gpioaster {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06		0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08		0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11		0x1b0b0
+		>;
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-eval-v3.dts
new file mode 100644
index 000000000000..f50a26dd34c0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-eval-v3.dts
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Fixed crystal dedicated to mcp251x */
+	clk16m: clock-16m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <16000000>;
+		clock-output-names = "clk16m";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	status = "okay";
+
+	mcp251x0: mcp251x@0 {
+		compatible = "microchip,mcp2515";
+		clocks = <&clk16m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <27 0x2>;
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		status = "okay";
+	};
+};
+
+/*
+ * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
+ */
+&i2c3 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_weim_gpio_1 &pinctrl_weim_gpio_2
+		&pinctrl_weim_gpio_3 &pinctrl_weim_gpio_4
+		&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
+		&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
+	>;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
+
+&weim {
+	status = "okay";
+
+	/* weim memory map: 32MB on CS0, CS1, CS2 and CS3 */
+	ranges = <0 0 0x08000000 0x02000000
+		  1 0 0x0a000000 0x02000000
+		  2 0 0x0c000000 0x02000000
+		  3 0 0x0e000000 0x02000000>;
+
+	/* SRAM on Colibri nEXT_CS0 */
+	sram@0,0 {
+		compatible = "cypress,cy7c1019dv33-10zsxi", "mtd-ram";
+		reg = <0 0 0x00010000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
+				      0x00000000 0x04000040 0x00000000>;
+	};
+
+	/* SRAM on Colibri nEXT_CS1 */
+	sram@1,0 {
+		compatible = "cypress,cy7c1019dv33-10zsxi", "mtd-ram";
+		reg = <1 0 0x00010000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
+				      0x00000000 0x04000040 0x00000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris-v2.dts
new file mode 100644
index 000000000000..3a6d3889760d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris-v2.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-iris.dts"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Iris V2 Board";
+	compatible = "toradex,colibri_imx6dl-iris-v2", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+		regulator-name = "3v3_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_iris	&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1>;
+
+	pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11	0x1b0b0
+		>;
+	};
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	cap-power-off-card;
+	/* uncomment the following to enable SD card UHS mode if you have a V1.1 module */
+	/* /delete-property/ no-1-8-v; */
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris.dts
new file mode 100644
index 000000000000..4303c88bb2a9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris.dts
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Iris Board";
+	compatible = "toradex,colibri_imx6dl-iris", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	status = "okay";
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_forceoff &pinctrl_uart23_forceoff>;
+
+	/*
+	 * uart-a-on-x13-enable turns the UART transceiver for UART_A on. If one
+	 * wants to turn the transceiver off, that property has to be deleted
+	 * and the gpio handled in userspace.
+	 * The same applies to uart-b-c-on-x14-enable where the UART_B and
+	 * UART_C transceiver is turned on.
+	 */
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <8 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+/*
+ * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
+ */
+&i2c3 {
+	status = "okay";
+
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_gpio_iris
+		&pinctrl_usbh_oc_1
+		&pinctrl_usbc_id_1
+	>;
+
+	pinctrl_gpio_iris: gpioirisgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21	0x1b0b0
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20	0x1b0b0
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19	0x1b0b0
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18	0x1b0b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06	0x1b0b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27	0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03	0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15	0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1_forceoff: uart1forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+		>;
+	};
+
+	pinctrl_uart23_forceoff: uart23forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+		>;
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-emmc-som-v15.dts
index 2b2fc360b865..2b2fc360b865 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-som-v15.dts
index e09c565d1d1f..e09c565d1d1f 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-cubox-i.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i.dts
index 2b1b3e193f53..2b1b3e193f53 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i.dts
diff --git a/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-dfi-fs700-m60.dts
index cece4aafdad8..cece4aafdad8 100644
--- a/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-dfi-fs700-m60.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-picoitx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-picoitx.dts
new file mode 100644
index 000000000000..038bb0025556
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-picoitx.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 DH electronics GmbH
+ *
+ * DHCOM iMX6 variant:
+ * DHCM-iMX6DL-C0800-R102-F0819-E-SD-RTC-T-HS-I-01D2
+ * DHCOM PCB number: 493-300 or newer
+ * PicoITX PCB number: 487-600 or newer
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-dhcom-som.dtsi"
+#include "imx6qdl-dhcom-picoitx.dtsi"
+
+/ {
+	model = "DH electronics i.MX6DL DHCOM on PicoITX";
+	compatible = "dh,imx6dl-dhcom-picoitx", "dh,imx6dl-dhcom-som",
+		     "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-eckelmann-ci4x10.dts
index 9eb2b73951b2..33825b5a8f26 100644
--- a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-eckelmann-ci4x10.dts
@@ -28,6 +28,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_usb_h1_vbus: regulator-usb-h1-vbus {
@@ -64,10 +65,17 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&rmii_clk>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&rmii_clk>;
+};
+
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio5 12 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	flash@0 {
@@ -80,7 +88,7 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	tpm@0 {
@@ -297,7 +305,6 @@
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
 	phy-handle = <&phy>;
-	clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
 	status = "okay";
 
 	mdio {
diff --git a/arch/arm/boot/dts/imx6dl-emcon-avari.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dts
index 407ad8d43c84..77d7600b2675 100644
--- a/arch/arm/boot/dts/imx6dl-emcon-avari.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
diff --git a/arch/arm/boot/dts/imx6dl-gw51xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dts
index 9956d12a1245..9956d12a1245 100644
--- a/arch/arm/boot/dts/imx6dl-gw51xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw52xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw52xx.dts
index 9ea23dd54f3c..9ea23dd54f3c 100644
--- a/arch/arm/boot/dts/imx6dl-gw52xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw52xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw53xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw53xx.dts
index 182e8194c249..182e8194c249 100644
--- a/arch/arm/boot/dts/imx6dl-gw53xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw53xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw54xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw54xx.dts
index a106c4e3e329..a106c4e3e329 100644
--- a/arch/arm/boot/dts/imx6dl-gw54xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw54xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw551x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw551x.dts
index 82d5f85722ea..82d5f85722ea 100644
--- a/arch/arm/boot/dts/imx6dl-gw551x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw551x.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw552x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw552x.dts
index 4864a36f9b36..4864a36f9b36 100644
--- a/arch/arm/boot/dts/imx6dl-gw552x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw552x.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw553x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw553x.dts
index 59b8afc36e66..59b8afc36e66 100644
--- a/arch/arm/boot/dts/imx6dl-gw553x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw553x.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw560x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dts
index 21bdfaf8df53..21bdfaf8df53 100644
--- a/arch/arm/boot/dts/imx6dl-gw560x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw5903.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5903.dts
index 103261ea9334..103261ea9334 100644
--- a/arch/arm/boot/dts/imx6dl-gw5903.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5903.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw5904.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5904.dts
index 9c6d3cd3d6a7..9c6d3cd3d6a7 100644
--- a/arch/arm/boot/dts/imx6dl-gw5904.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5904.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw5907.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5907.dts
new file mode 100644
index 000000000000..3fa2822beffc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5907.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5907.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW5907";
+	compatible = "gw,imx6dl-gw5907", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw5910.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5910.dts
new file mode 100644
index 000000000000..0d5e7e5da536
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5910.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5910.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW5910";
+	compatible = "gw,imx6dl-gw5910", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw5912.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5912.dts
new file mode 100644
index 000000000000..5260e0142d63
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5912.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5912.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW5912";
+	compatible = "gw,imx6dl-gw5912", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw5913.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5913.dts
new file mode 100644
index 000000000000..b74e533c8e67
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5913.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5913.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW5913";
+	compatible = "gw,imx6dl-gw5913", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-emmc-som-v15.dts
index a63f742f20d9..a63f742f20d9 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-som-v15.dts
index 66a06cf3cdf3..66a06cf3cdf3 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard.dts
index cbd02eb486e1..cbd02eb486e1 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard2-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-emmc-som-v15.dts
index 80313c13bcdb..80313c13bcdb 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard2-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard2-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-som-v15.dts
index e61ef1156f8b..e61ef1156f8b 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard2-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2.dts
index b12cd87f3f94..b12cd87f3f94 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2.dts
diff --git a/arch/arm/boot/dts/imx6dl-icore-mipi.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-mipi.dts
index e43bccb78ab2..d8f3821a0ffd 100644
--- a/arch/arm/boot/dts/imx6dl-icore-mipi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-mipi.dts
@@ -8,7 +8,7 @@
 /dts-v1/;
 
 #include "imx6dl.dtsi"
-#include "imx6qdl-icore.dtsi"
+#include "imx6qdl-icore-1.5.dtsi"
 
 / {
 	model = "Engicam i.CoreM6 DualLite/Solo MIPI Starter Kit";
diff --git a/arch/arm/boot/dts/imx6dl-icore-rqs.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-rqs.dts
index 73d710d34b9d..73d710d34b9d 100644
--- a/arch/arm/boot/dts/imx6dl-icore-rqs.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-rqs.dts
diff --git a/arch/arm/boot/dts/imx6dl-icore.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-icore.dts
index 80fa60607ab1..80fa60607ab1 100644
--- a/arch/arm/boot/dts/imx6dl-icore.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-icore.dts
diff --git a/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i.dtsi
index a864fdbd5f16..a864fdbd5f16 100644
--- a/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-lanmcu.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-lanmcu.dts
new file mode 100644
index 000000000000..7c62db91173b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-lanmcu.dts
@@ -0,0 +1,483 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2019 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Van der Laan LANMCU";
+	compatible = "vdl,lanmcu", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	clock_ksz8081: clock-ksz8081 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 1000>;
+		num-interpolated-steps = <20>;
+		default-brightness-level = <19>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0bdh6";
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usdhc2_wifi_pwrseq: usdhc2-wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+	};
+
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&clock_ksz8081>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "BL_PWM", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "ENET_LED_GREEN",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "TS_INT", "USB_OTG1_OC", "USB_OTG1_PWR", "",
+		"", "", "", "", "UART2_CTS", "", "UART3_CTS", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "ENET_RST", "ENET_INT",
+		"", "", "I2C1_SDA", "I2C1_SCL", "", "", "", "";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "WLAN_REG_ON", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio7 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"EMMC_RST", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ts_edt>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+
+		touchscreen-size-x = <1792>;
+		touchscreen-size-y = <1024>;
+
+		touchscreen-fuzz-x = <0>;
+		touchscreen-fuzz-y = <0>;
+
+		/* Touch screen calibration */
+		threshold = <50>;
+		gain = <5>;
+		offset = <10>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	no-1-8-v;
+	non-removable;
+	mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_disp: ipudisp1grp {
+		fsl,pins = <
+			/* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x30
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x30
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x30
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x30
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x30
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x30
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x30
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x30
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x30
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x30
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x30
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x30
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x30
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x30
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x30
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x30
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x30
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x30
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x30
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x30
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x30
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x30
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT			0x8
+		>;
+	};
+
+	pinctrl_ts_edt: ts1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x1b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_RX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_CTS_B			0x130b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D30__UART3_CTS_B			0x130b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__SD1_CD_B			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD			0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK			0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0			0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1			0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2			0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3			0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+
+	pinctrl_wifi_npd: wifigrp {
+		fsl,pins = <
+			/* WL_REG_ON */
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10		0x13069
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
index 385ce7b0029e..028951955bde 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
@@ -303,6 +303,7 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6.dtsi
new file mode 100644
index 000000000000..b749b424bbd6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&ethphy {
+	rxdv-skew-ps = <180>;
+	txen-skew-ps = <0>;
+	rxd3-skew-ps = <180>;
+	rxd2-skew-ps = <180>;
+	rxd1-skew-ps = <180>;
+	rxd0-skew-ps = <180>;
+	txd3-skew-ps = <120>;
+	txd2-skew-ps = <0>;
+	txd1-skew-ps = <300>;
+	txd0-skew-ps = <120>;
+	txc-skew-ps = <1860>;
+	rxc-skew-ps = <1860>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-mba6a.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6a.dts
new file mode 100644
index 000000000000..df0a96b28af0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6a.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6dl-tqma6a.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6a.dtsi"
+#include "imx6dl-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6S/DL on MBa6x";
+	compatible = "tq,imx6dl-mba6x-a", "tq,mba6a",
+		     "tq,imx6dl-tqma6dl-a", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-mba6b.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6b.dts
new file mode 100644
index 000000000000..610b19d2db0f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6b.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6dl-tqma6b.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6b.dtsi"
+#include "imx6dl-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6S/DL on MBa6x";
+	compatible = "tq,imx6dl-mba6x-b", "tq,mba6b",
+		     "tq,imx6dl-tqma6dl-b", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-nit6xlite.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-nit6xlite.dts
index 61fa30991d67..61fa30991d67 100644
--- a/arch/arm/boot/dts/imx6dl-nit6xlite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-nit6xlite.dts
diff --git a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-nitrogen6x.dts
index ef58d3b0ea0d..ef58d3b0ea0d 100644
--- a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-nitrogen6x.dts
diff --git a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-mira-rdk-nand.dts
index 9f7f9f98139d..d906a7f05aaa 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
 #include "imx6dl.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira DualLite/Solo Carrier-Board with NAND";
diff --git a/arch/arm/boot/dts/imx6dl-phytec-pbab01.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pbab01.dts
index 0a07cc6f815e..0a07cc6f815e 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-pbab01.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pbab01.dts
diff --git a/arch/arm/boot/dts/imx6dl-phytec-pfla02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pfla02.dtsi
index 6f8aaf524425..6f8aaf524425 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pfla02.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-dwarf.dts
new file mode 100644
index 000000000000..d85b15a8c127
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-dwarf.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-pico-pi.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 DualLite/Solo Board and Dwarf baseboard";
+	compatible = "technexion,imx6dl-pico-dwarf", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-hobbit.dts
new file mode 100644
index 000000000000..08fedcbcc91b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-hobbit.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-pico-hobbit.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 DualLite/Solo Board and Hobbit baseboard";
+	compatible = "technexion,imx6dl-pico-hobbit", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-pico-nymph.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-nymph.dts
new file mode 100644
index 000000000000..32ccfc5d41ce
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-nymph.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-pico-pi.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 DualLite/Solo Board and Nymph baseboard";
+	compatible = "technexion,imx6dl-pico-nymph", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-pi.dts
new file mode 100644
index 000000000000..4590e8ad9a91
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-pi.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-pico-pi.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 DualLite/Solo Board and PI baseboard";
+	compatible = "technexion,imx6dl-pico-pi", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6dl-pinfunc.h
index 9d88d09f9bf6..9d88d09f9bf6 100644
--- a/arch/arm/boot/dts/imx6dl-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pinfunc.h
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-plybas.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-plybas.dts
new file mode 100644
index 000000000000..84f34da06267
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-plybas.dts
@@ -0,0 +1,396 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent BAS board";
+	compatible = "ply,plybas", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		button-start {
+			label = "START";
+			linux,code = <31>;
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+		};
+
+		button-clean {
+			label = "CLEAN";
+			linux,code = <46>;
+			gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			label = "debug1";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "light_tower1";
+			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-3 {
+			label = "light_tower2";
+			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "light_tower3";
+			gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			label = "light_tower4";
+			gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+			"IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+		"IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+			"IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+		"IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+			"IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+		"IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-delay = <0 20>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG_0 */
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+			/* DEBUG_1 */
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09			0x1b0b0
+
+			/* LED1 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22		0x13070
+			/* LED2 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23		0x13070
+			/* LED3 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24		0x13070
+			/* LED4 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25		0x13070
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B		0x130b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..dfa8110b1d97
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dts
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent M2M board";
+	compatible = "ply,plym2m", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 1000>;
+		num-interpolated-steps = <20>;
+		default-brightness-level = <19>;
+		power-supply = <&reg_12v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0bdh6";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
+
+			trips {
+				alert {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+
+			trips {
+				alert {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
+
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
+
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc2046>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 {
+			reg = <0>;
+			settling-time-us = <300>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@2 {
+			reg = <2>;
+			settling-time-us = <300>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		/* channel 6 is not connected */
+
+		channel@7 {
+			reg = <7>;
+			settling-time-us = <300>;
+			oversampling-ratio = <5>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	tsens0: temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usbotg {
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO			0x10000
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK			0x3008
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_disp: ipudisp1grp {
+		fsl,pins = <
+			/* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x30
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x30
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x30
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x30
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x30
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x30
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x30
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x30
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x30
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x30
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x30
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x30
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x30
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x30
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x30
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x30
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x30
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x30
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x30
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x30
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x30
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x30
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT			0x8
+		>;
+	};
+
+	pinctrl_tsc2046: tsc2046grp {
+		fsl,pins = <
+			/* TSC_PENIRQ */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x1b0b1
+			/* TSC_BUSY */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-prtmvt.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-prtmvt.dts
new file mode 100644
index 000000000000..773a84a5739d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-prtmvt.dts
@@ -0,0 +1,860 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Protonic MVT board";
+	compatible = "prt,prtmvt", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <1>;
+		power-supply = <&reg_3v3>;
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-f1 {
+			label = "GPIO Key F1";
+			linux,code = <KEY_F1>;
+			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f2 {
+			label = "GPIO Key F2";
+			linux,code = <KEY_F2>;
+			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f3 {
+			label = "GPIO Key F3";
+			linux,code = <KEY_F3>;
+			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f4 {
+			label = "GPIO Key F4";
+			linux,code = <KEY_F4>;
+			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f5 {
+			label = "GPIO Key F5";
+			linux,code = <KEY_F5>;
+			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+		};
+
+		key-cycle {
+			label = "GPIO Key CYCLE";
+			linux,code = <KEY_CYCLEWINDOWS>;
+			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+		};
+
+		key-esc {
+			label = "GPIO Key ESC";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+		};
+
+		key-up {
+			label = "GPIO Key UP";
+			linux,code = <KEY_UP>;
+			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+		};
+
+		key-down {
+			label = "GPIO Key DOWN";
+			linux,code = <KEY_DOWN>;
+			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+		};
+
+		key-ok {
+			label = "GPIO Key OK";
+			linux,code = <KEY_OK>;
+			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f6 {
+			label = "GPIO Key F6";
+			linux,code = <KEY_F6>;
+			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f7 {
+			label = "GPIO Key F7";
+			linux,code = <KEY_F7>;
+			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f8 {
+			label = "GPIO Key F8";
+			linux,code = <KEY_F8>;
+			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f9 {
+			label = "GPIO Key F9";
+			linux,code = <KEY_F9>;
+			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f10 {
+			label = "GPIO Key F10";
+			linux,code = <KEY_F10>;
+			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+		};
+
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "debug1";
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		led-2 {
+			label = "power_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg070wvlq", "lg,lb070wv8";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_h1_vbus: regulator-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "h1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0				IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>, <&clk50m_phy>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-handle = <&rmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <3000>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
+			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "", "", "", "", "", "", "ON_SWITCH",
+		"POWER_LED", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+			"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
+		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+			"YACO_RESET";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "", "", "", "",
+		"CPU_LIGHT_ON", "", "ETH_RESET", "", "BL_EN",
+			"BL_PWM", "ETH_INTRP", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	video@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+
+	gpio_pca: gpio@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9539>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&ssi1 {
+	#sound-dai-cells = <0>;
+	fsl,mode = "ac97-slave";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_h1_vbus>;
+	pinctrl-names = "default";
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* ITU656_nRESET */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
+			/* CAM1_MIRROR */
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
+			/* CAM2_MIRROR */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
+			/* CAM_nDETECT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
+			/* ISB_IN1 */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
+			/* ISB_nIN2 */
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
+			/* WARN_LIGHT */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
+			/* ON2_FB */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
+			/* YACO_nIRQ */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
+			/* YACO_BOOT0 */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
+			/* YACO_nRESET */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
+			/* FORCE_ON1 */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+			/* AUDIO_nRESET */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
+			/* ITU656_nPDN */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
+
+			/* HW revision detect */
+			/* REV_ID0 */
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
+			/* REV_ID1 */
+			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
+			/* REV_ID2 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
+			/* REV_ID3 */
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
+			/* REV_ID4 */
+			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
+
+			/* New in HW revision 1 */
+			/* ON1_FB */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
+			/* DIP1_FB */
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG0 */
+			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
+			/* DEBUG1 */
+			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
+			/* POWER_LED */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+		>;
+	};
+
+	pinctrl_pca9539: pca9539 {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+		>;
+	};
+
+	/* YaCO Touchscreen UART */
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-prtrvt.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-prtrvt.dts
new file mode 100644
index 000000000000..36b031236e47
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-prtrvt.dts
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Protonic RVT board";
+	compatible = "prt,prtrvt", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x10000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-debug0 {
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+
+	nfc@0 {
+		compatible = "ti,trf7970a";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nfc>;
+		spi-max-frequency = <2000000>;
+		interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
+		ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
+				  <&gpio5 11 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_3v3>;
+		autosuspend-delay = <30000>;
+		irq-status-read-quirk;
+		en2-rf-quirk;
+		status = "okay";
+	};
+};
+
+&i2c3 {
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* nc */
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		/* nc */
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		/* can1_l */
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		/* can1_h */
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "disabled";
+};
+
+&usbotg {
+	disable-over-current;
+};
+
+&vpu {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_can1phy: can1phy {
+		fsl,pins = <
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12	0x13070
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x000b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0
+		>;
+	};
+
+	pinctrl_nfc: nfcgrp {
+		fsl,pins = <
+			/* NFC_ASK_OOK */
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09	0x100b1
+			/* NFC_PWR_EN */
+			MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10	0x100b1
+			/* NFC_EN2 */
+			MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11	0x100b1
+			/* NFC_EN */
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x100b1
+			/* NFC_MOD */
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x100b1
+			/* NFC_IRQ */
+			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x100b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-prtvt7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-prtvt7.dts
new file mode 100644
index 000000000000..568e98cb62aa
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-prtvt7.dts
@@ -0,0 +1,612 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	model = "Protonic VT7";
+	compatible = "prt,prtvt7", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 0>;
+		brightness-levels = <0 20 81 248 1000>;
+		default-brightness-level = <65>;
+		num-interpolated-steps = <21>;
+		power-supply = <&reg_bl_12v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-esc {
+			label = "GPIO Key ESC";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+		};
+
+		key-up {
+			label = "GPIO Key UP";
+			linux,code = <KEY_UP>;
+			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+		};
+
+		key-down {
+			label = "GPIO Key DOWN";
+			linux,code = <KEY_DOWN>;
+			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+		};
+
+		key-enter {
+			label = "GPIO Key Enter";
+			linux,code = <KEY_ENTER>;
+			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+		};
+
+		key-cycle {
+			label = "GPIO Key CYCLE";
+			linux,code = <KEY_CYCLEWINDOWS>;
+			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f1 {
+			label = "GPIO Key F1";
+			linux,code = <KEY_F1>;
+			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f2 {
+			label = "GPIO Key F2";
+			linux,code = <KEY_F2>;
+			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f3 {
+			label = "GPIO Key F3";
+			linux,code = <KEY_F3>;
+			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f4 {
+			label = "GPIO Key F4";
+			linux,code = <KEY_F4>;
+			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f5 {
+			label = "GPIO Key F5";
+			linux,code = <KEY_F5>;
+			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f6 {
+			label = "GPIO Key F6";
+			linux,code = <KEY_F6>;
+			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f7 {
+			label = "GPIO Key F7";
+			linux,code = <KEY_F7>;
+			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f8 {
+			label = "GPIO Key F8";
+			linux,code = <KEY_F8>;
+			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f9 {
+			label = "GPIO Key F9";
+			linux,code = <KEY_F9>;
+			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+		};
+
+		key-f10 {
+			label = "GPIO Key F10";
+			linux,code = <KEY_F10>;
+			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-debug0 {
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
+	reg_bl_12v0: regulator-bl-12v0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_bl_12v0>;
+		regulator-name = "bl-12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
+
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
+
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0		       IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+	};
+};
+
+&i2c1 {
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_codec>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	video@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	tsens0: temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	gpio_pca: gpio@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+};
+
+&ipu1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_can1phy: can1phy {
+		fsl,pins = <
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x13070
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
+		>;
+	};
+
+	pinctrl_codec: codecgrp {
+		fsl,pins = <
+			/* AUDIO_nRESET */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x1f0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO		0x100b1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK		0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI		0x100b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x000b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19	0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+			/* ITU656_nRESET */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			/* ITU656_nPDN */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b0
+		>;
+	};
+
+	pinctrl_ipu1_disp: ipudisp1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15	   0xb0
+
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
+
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
+
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b0
+		>;
+	};
+
+	pinctrl_reg_bl_12v0: 12blgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_tsc: tscgrp {
+
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x1b0b0
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-qmx6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-qmx6.dtsi
new file mode 100644
index 000000000000..8a637fdff073
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-qmx6.dtsi
@@ -0,0 +1,612 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Device Tree Source for i.MX6DL based congatec QMX6
+// System on Module
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+// Copyright 2016 congatec AG
+
+#include "imx6dl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	memory@10000000 {
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_3p3v: 3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c2>;
+
+		i2c5: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c6: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+
+	mux-ssi1 {
+		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_TFSDIR |
+			IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT6) |
+			IMX_AUDMUX_V2_PTCR_TCLKDIR |
+			IMX_AUDMUX_V2_PTCR_TCSEL(MX51_AUDMUX_PORT6) |
+			IMX_AUDMUX_V2_PTCR_SYN)
+			IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT6)
+		>;
+	};
+
+	mux-aud6 {
+		fsl,audmux-port = <MX51_AUDMUX_PORT6>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN
+			IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT1_SSI0)
+		>;
+	};
+};
+
+&clks {
+	clocks = <&rtc_sqw>;
+	clock-names = "ckil";
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+				 <&clks IMX6QDL_CLK_PLL2_PFD0_352M>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf032b", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "bootloader";
+			reg = <0x0000000 0x100000>;
+		};
+
+		partition@100000 {
+			label = "user";
+			reg = <0x0100000 0x2fc000>;
+		};
+
+		partition@3fc000 {
+			label = "reserved";
+			reg = <0x03fc000 0x4000>;
+			read-only;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet &pinctrl_phy_reset>;
+	phy-mode = "rgmii-id";
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	fsl,magic-packet;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@6 {
+			reg = <6>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	rtc: m41t62@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+
+		rtc_sqw: clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&i2c6 {
+	pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/*
+			 * keep VGEN3, VGEN4 and VGEN5 enabled in order to
+			 * maintain backward compatibility with hw-rev. A.0
+			 */
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			/* supply voltage for eMMC */
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&pcie {
+	reset-gpio = <&gpio1 20 0>;
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+};
+
+&reg_arm {
+	vin-supply = <&sw1a_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1c_reg>;
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbh1 {
+	/* Connected to USB-Hub SMSC USB2514, provides P0, P2, P3, P4 on Qseven connector */
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+};
+
+&usdhc2 {
+	/* MicroSD card slot */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usdhc3 {
+	/* eMMC module */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	non-removable;
+	bus-width = <8>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	qmx6mux: imx6qdl-qmx6 {
+		pinctrl_audmux: audmuxgrp {
+			fsl,pins = <
+				MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x110b0 /* Q7[67] HDA_SDO */
+				MX6QDL_PAD_DI0_PIN3__AUD6_TXFS		0x30b0 /* Q7[59] HDA_SYNC */
+				MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x30b0 /* Q7[65] HDA_SDI */
+				MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x30b0 /* Q7[63] HDA_BITCLK */
+			>;
+		};
+
+		/* PHY is on System on Module, Q7[3-15] have Ethernet lines */
+		pinctrl_enet: enet {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+				MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			>;
+		};
+
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000 /* PCIE_WAKE_B */
+				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x80000000 /* I2C multiplexer */
+				MX6QDL_PAD_NANDF_D6__GPIO2_IO06		0x80000000 /* SD4_CD# */
+				MX6QDL_PAD_NANDF_D7__GPIO2_IO07		0x80000000 /* SD4_WP */
+				MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x80000000 /* Camera MCLK */
+			>;
+		};
+
+		pinctrl_i2c1: i2c1 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1 /* Q7[66] I2C_CLK */
+				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1 /* Q7[68] I2C_DAT */
+			>;
+		};
+
+		pinctrl_i2c1_gpio: i2c1-gpio {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x1b0b0 /* Q7[66] I2C_CLK */
+				MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x1b0b0 /* Q7[68] I2C_DAT */
+			>;
+		};
+
+		pinctrl_i2c2: i2c2 {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1 /* Q7[152] SDVO_CTRL_CLK */
+				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1 /* Q7[150] SDVO_CTRL_DAT */
+			>;
+		};
+
+		pinctrl_i2c2_gpio: i2c2-gpio {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0 /* Q7[152] SDVO_CTRL_CLK */
+				MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x1b0b0 /* Q7[150] SDVO_CTRL_DAT */
+			>;
+		};
+
+		pinctrl_i2c3: i2c3 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1 /* Q7[60] SMB_CLK */
+				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1 /* Q7[62] SMB_DAT */
+			>;
+		};
+
+		pinctrl_i2c3_gpio: i2c3-gpio {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x1b0b0 /* Q7[60] SMB_CLK */
+				MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0 /* Q7[62] SMB_DAT */
+			>;
+		};
+
+		pinctrl_phy_reset: phy-reset {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0 /* RGMII Phy Reset */
+			>;
+		};
+
+		pinctrl_pwm4: pwm4 {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1 /* Q7[123] LVDS_BLT_CTRL */
+			>;
+		};
+
+		pinctrl_q7_backlight_enable: q7-backlight-enable {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x1b0b0 /* Q7[112] LVDS_BLEN */
+			>;
+		};
+
+		pinctrl_q7_gpio0: q7-gpio0 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0 /* Q7[185] GPIO0 */
+			>;
+		};
+
+		pinctrl_q7_gpio1: q7-gpio1 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0 /* Q7[186] GPIO1 */
+			>;
+		};
+
+		pinctrl_q7_gpio2: q7-gpio2 {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26	0x1b0b0 /* Q7[187] GPIO2 */
+			>;
+		};
+
+		pinctrl_q7_gpio3: q7-gpio3 {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27	0x1b0b0 /* Q7[188] GPIO3 */
+			>;
+		};
+
+		pinctrl_q7_gpio4: q7-gpio4 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0 /* Q7[189] GPIO4 */
+			>;
+		};
+
+		pinctrl_q7_gpio5: q7-gpio5 {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0 /* Q7[190] GPIO5 */
+			>;
+		};
+
+		pinctrl_q7_gpio6: q7-gpio6 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_16__GPIO7_IO11		0x1b0b0 /* Q7[191] GPIO6 */
+			>;
+		};
+
+		pinctrl_q7_gpio7: q7-gpio7 {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0 /* Q7[192] GPIO7 */
+			>;
+		};
+
+		pinctrl_q7_hda_reset: q7-hda-reset {
+			fsl,pins = <
+				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0 /* Q7[61] HDA_RST_N */
+			>;
+		};
+
+		pinctrl_q7_lcd_power: lcd-power {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x1b0b0 /* Q7[111] LVDS_PPEN */
+			>;
+		};
+
+		pinctrl_q7_sdio_power: q7-sdio-power {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30	0x1b0b0 /* Q7[47] SDIO_PWR# */
+			>;
+		};
+
+		pinctrl_q7_sleep_button: q7-sleep-button {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0 /* Q7[21] SLP_BTN# */
+			>;
+		};
+
+		pinctrl_q7_spi_cs1: spi-cs1 {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x1b0b0 /* Q7[202] SPI_CS1# */
+			>;
+		};
+
+		/* SPI1 bus does not leave System on Module */
+		pinctrl_spi1: spi1 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
+			>;
+		};
+
+		/* Debug connector on Q7 module */
+		pinctrl_uart2: uart2 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_uart3: uart3 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1 /* Q7[177] UART0_RX */
+				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1 /* Q7[171] UART0_TX */
+			>;
+		};
+
+		pinctrl_usbotg: usbotg {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059 /* Q7[92] USB_ID */
+			>;
+		};
+
+		/* µSD card slot on Q7 module */
+		pinctrl_usdhc2: usdhc2 {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0 /* SD2_CD */
+			>;
+		};
+
+		/* eMMC module on Q7 module */
+		pinctrl_usdhc3: usdhc3 {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+			>;
+		};
+
+		pinctrl_usdhc4: usdhc4 {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059 /* Q7[45] SDIO_CMD */
+				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x17059 /* Q7[42] SDIO_CLK */
+				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059 /* Q7[48] SDIO_DAT1 */
+				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059 /* Q7[49] SDIO_DAT0 */
+				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059 /* Q7[50] SDIO_DAT3 */
+				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059 /* Q7[51] SDIO_DAT2 */
+			>;
+		};
+
+		pinctrl_wdog: wdog {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0 /* Watchdog output signal */
+			>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-rex-basic.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-rex-basic.dts
index 0f1616bfa9a8..b72f8ea1e6f6 100644
--- a/arch/arm/boot/dts/imx6dl-rex-basic.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-rex-basic.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-riotboard.dts
index 829654e1835a..114739d10447 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-riotboard.dts
@@ -25,14 +25,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -89,11 +89,28 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
+	phy-handle = <&rgmii_phy>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Atheros AR8035 PHY */
+		rgmii_phy: ethernet-phy@4 {
+			reg = <4>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <1000>;
+			qca,smarteee-tw-us-1g = <24>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
 };
 
 &gpio1 {
@@ -155,12 +172,13 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};
 
-	pmic: pf0100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 		interrupt-parent = <&gpio5>;
diff --git a/arch/arm/boot/dts/imx6dl-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sabreauto.dts
index ff3283c83a39..ff3283c83a39 100644
--- a/arch/arm/boot/dts/imx6dl-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sabreauto.dts
diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dts
index 33040761b253..33040761b253 100644
--- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dts
diff --git a/arch/arm/boot/dts/imx6dl-sabresd.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sabresd.dts
index cd6bbf22a16f..cd6bbf22a16f 100644
--- a/arch/arm/boot/dts/imx6dl-sabresd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sabresd.dts
diff --git a/arch/arm/boot/dts/imx6dl-savageboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-savageboard.dts
index b95469c520a4..b95469c520a4 100644
--- a/arch/arm/boot/dts/imx6dl-savageboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-savageboard.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dts
new file mode 100644
index 000000000000..b12b5aabe70a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+#include "imx6qdl-skov-revc-lt2.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU SoloCore";
+	compatible = "skov,imx6dl-skov-revc-lt2", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt6.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt6.dts
new file mode 100644
index 000000000000..5dcc433fe2af
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt6.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU SoloCore";
+	compatible = "skov,imx6dl-skov-revc-lt6", "fsl,imx6dl";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "logictechno,lttd800480070-l6wh-rt";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/vf610-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-solidsense.dts
index ef9b4d6209f6..2a3699adbed0 100644
--- a/arch/arm/boot/dts/vf610-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-solidsense.dts
@@ -1,5 +1,6 @@
 /*
- * Copyright 2014 Toradex AG
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on dt work by Russell King
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -38,12 +39,16 @@
  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
-
 /dts-v1/;
-#include "vf610-colibri.dtsi"
-#include "vf-colibri-eval-v3.dtsi"
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+#include "imx6qdl-solidsense.dtsi"
 
 / {
-	model = "Toradex Colibri VF61 on Colibri Evaluation Board";
-	compatible = "toradex,vf610-colibri_vf61-on-eval", "toradex,vf610-colibri_vf61", "fsl,vf610";
+	model = "SolidRun SolidSense Solo/DualLite (1.5som+emmc)";
+	compatible = "solidrun,solidsense/dl", "fsl,imx6dl";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6a.dtsi
new file mode 100644
index 000000000000..e891ef9b0091
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6a.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-tqma6a.dtsi"
+#include "imx6qdl-tqma6.dtsi"
+
+/ {
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6b.dtsi
new file mode 100644
index 000000000000..38cd8501a886
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6b.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-tqma6b.dtsi"
+#include "imx6qdl-tqma6.dtsi"
+
+/ {
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-ts4900.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-ts4900.dts
index 3d60cc725d9e..3d60cc725d9e 100644
--- a/arch/arm/boot/dts/imx6dl-ts4900.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-ts4900.dts
diff --git a/arch/arm/boot/dts/imx6dl-ts7970.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-ts7970.dts
index 5da6feba2e66..5da6feba2e66 100644
--- a/arch/arm/boot/dts/imx6dl-ts7970.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-ts7970.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6dl-comtft.dts
index 51a9bb9d6bc2..51a9bb9d6bc2 100644
--- a/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6dl-comtft.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034-mb7.dts
index fc23b4d291a1..fc23b4d291a1 100644
--- a/arch/arm/boot/dts/imx6dl-tx6s-8034-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034-mb7.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034.dts
index 9eb2ef17339c..9eb2ef17339c 100644
--- a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035-mb7.dts
index 4101c6597721..4101c6597721 100644
--- a/arch/arm/boot/dts/imx6dl-tx6s-8035-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035-mb7.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035.dts
index a5532ecc18c5..a5532ecc18c5 100644
--- a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-801x.dts
index 67ed0452f5de..67ed0452f5de 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-801x.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033-mb7.dts
index d34189fc52d9..d34189fc52d9 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-8033-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033-mb7.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033.dts
index 7030b2654bbd..7030b2654bbd 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-80xx-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-80xx-mb7.dts
index aef5fcc42904..aef5fcc42904 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-80xx-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-80xx-mb7.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-811x.dts
index 5342f2f5a8a8..5342f2f5a8a8 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-811x.dts
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-81xx-mb7.dts
index c4588fb0bf6f..c4588fb0bf6f 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-81xx-mb7.dts
diff --git a/arch/arm/boot/dts/imx6dl-udoo.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-udoo.dts
index d871cac1711f..d871cac1711f 100644
--- a/arch/arm/boot/dts/imx6dl-udoo.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-udoo.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-victgo.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-victgo.dts
new file mode 100644
index 000000000000..4875afadb630
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-victgo.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+	model = "Kverneland TGO";
+	compatible = "kvg,victgo", "fsl,imx6dl";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-enter {
+			label = "Rotary Key";
+			gpios = <&gpio2 05 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+			wakeup-source;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
+	};
+
+	panel {
+		compatible = "lg,lb070wv8";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	rotary-encoder {
+		compatible = "rotary-encoder";
+		pinctrl-0 = <&pinctrl_rotary_ch>;
+		gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>,
+			<&gpio2 4 GPIO_ACTIVE_HIGH>;
+		linux,axis = <REL_WHEEL>;
+		rotary-encoder,steps-per-period = <4>;
+		rotary-encoder,relative-axis;
+		rotary-encoder,rollover;
+		wakeup-source;
+	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
+
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
+
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
+
+	vdiv_hitch_pos: voltage-divider-hitch-pos {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 6>;
+		output-ohms = <3300>;
+		full-ohms = <13300>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-handle = <&rmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "ETH_MDIO", "",
+		"", "", "", "", "", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+			"HITCH_IN_OUT",
+		"LIGHT_ON", "", "ETH_RESET", "CONTACT_IN", "BL_EN",
+			"BL_PWM", "ETH_INT", "ISB_LED";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
+			"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	keypad@70 {
+		compatible = "holtek,ht16k33";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_keypad>;
+		reg = <0x70>;
+		refresh-rate-hz = <20>;
+		debounce-delay-ms = <50>;
+		interrupts-extended = <&gpio4 5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+		keypad,num-rows = <12>;
+		keypad,num-columns = <3>;
+		linux,keymap = <
+			MATRIX_KEY(2, 0, KEY_F6)
+			MATRIX_KEY(3, 0, KEY_F8)
+			MATRIX_KEY(4, 0, KEY_F10)
+			MATRIX_KEY(5, 0, KEY_F4)
+			MATRIX_KEY(6, 0, KEY_F2)
+			MATRIX_KEY(2, 1, KEY_F5)
+			MATRIX_KEY(3, 1, KEY_F7)
+			MATRIX_KEY(4, 1, KEY_F9)
+			MATRIX_KEY(5, 1, KEY_F3)
+			MATRIX_KEY(6, 1, KEY_F1)
+		      >;
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI		0x100b1
+			MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO		0x100b1
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12		0x100b1
+			MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK		0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* ROTARY_BTN */
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05			0x1b0b0
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+
+	pinctrl_keypad: keypadgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
+		>;
+	};
+
+	pinctrl_rotary_ch: rotarychgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03			0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04			0x1b0b0
+		>;
+	};
+
+	pinctrl_touchscreen: touchscreengrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08		0x1b0b0
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-vicut1.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-vicut1.dts
new file mode 100644
index 000000000000..5035d303447d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-vicut1.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
+
+/ {
+	model = "Kverneland UT1 Board";
+	compatible = "kvg,vicut1", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revb1.dts
index c2946fbaa0dd..c2946fbaa0dd 100644
--- a/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revb1.dts
diff --git a/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revd1.dts
index 6d1d863c2e3a..6d1d863c2e3a 100644
--- a/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revd1.dts
diff --git a/arch/arm/boot/dts/imx6dl-wandboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard.dts
index 4a08d5a99452..4a08d5a99452 100644
--- a/arch/arm/boot/dts/imx6dl-wandboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard.dts
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-common.dtsi
index 80ed5f16a76e..3be38a3c4bb1 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-common.dtsi
@@ -5,9 +5,17 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pwm/pwm.h>
 
 / {
+	aliases: aliases {
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
+	};
+
 	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
@@ -47,6 +55,7 @@
 	panel: panel {
 		compatible = "dataimage,scf0700c48ggu18";
 		power-supply = <&sw2_reg>;
+		backlight = <&backlight>;
 		status = "disabled";
 
 		port {
@@ -89,7 +98,6 @@
 		regulator-max-microvolt = <5000000>;
 		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
-		status = "okay";
 	};
 };
 
@@ -97,12 +105,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <20>;
 	phy-supply = <&sw2_reg>;
-	phy-handle = <&ethphy0>;
 	status = "okay";
 
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
 	mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -118,6 +128,7 @@
 		switch@10 {
 			compatible = "qca,qca8334";
 			reg = <10>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 
 			switch_ports: ports {
 				#address-cells = <1>;
@@ -135,13 +146,13 @@
 					};
 				};
 
-				port@2 {
+				eth2: port@2 {
 					reg = <2>;
 					label = "eth2";
 					phy-handle = <&phy_port2>;
 				};
 
-				port@3 {
+				eth1: port@3 {
 					reg = <3>;
 					label = "eth1";
 					phy-handle = <&phy_port3>;
@@ -257,30 +268,32 @@
 		compatible = "ti,lp5562";
 		reg = <0x30>;
 		clock-mode = /bits/ 8 <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 		status = "disabled";
 
-		chan0 {
+		led@0 {
 			chan-name = "R";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <0>;
+			color = <LED_COLOR_ID_RED>;
 		};
 
-		chan1 {
+		led@1 {
 			chan-name = "G";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
 		};
 
-		chan2 {
+		led@2 {
 			chan-name = "B";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
-		};
-
-		chan3 {
-			chan-name = "W";
-			led-cur = /bits/ 8 <0x0>;
-			max-cur = /bits/ 8 <0x0>;
+			reg = <2>;
+			color = <LED_COLOR_ID_BLUE>;
 		};
 	};
 
@@ -288,7 +301,6 @@
 		compatible = "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <64>;
-		status = "okay";
 	};
 
 	touchscreen: touchscreen@5c {
@@ -298,7 +310,7 @@
 		interrupt-parent = <&gpio4>;
 		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
-		reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		touchscreen-size-x = <800>;
 		touchscreen-size-y = <480>;
 		status = "disabled";
@@ -311,12 +323,26 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	oled: oled@3d {
+	oled_1309: oled@3c {
+		compatible = "solomon,ssd1309fb-i2c";
+		reg = <0x3c>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,segment-no-remap;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	oled_1305: oled@3d {
 		compatible = "solomon,ssd1305fb-i2c";
 		reg = <0x3d>;
 		solomon,height = <64>;
 		solomon,width = <128>;
 		solomon,page-offset = <0>;
+		solomon,col-offset = <4>;
 		solomon,prechargep2 = <15>;
 		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
 		vbat-supply = <&sw2_reg>;
@@ -540,7 +566,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "disabled";
@@ -562,6 +587,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
 	vbus-supply = <&reg_usb_h1_vbus>;
+	over-current-active-low;
 	status = "disabled";
 };
 
@@ -569,6 +595,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
 	vbus-supply = <&reg_usb_otg_vbus>;
+	over-current-active-low;
 	srp-disable;
 	hnp-disable;
 	adp-disable;
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-draco.dts
index a38c407fd837..a38c407fd837 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-draco.dts
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-hydra.dts
index 6010d3d872ab..a19609c7c7c0 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-hydra.dts
@@ -29,7 +29,11 @@
 	status = "okay";
 };
 
-&oled {
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-lynx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-lynx.dts
new file mode 100644
index 000000000000..5c2cd517589b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-lynx.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Lynx i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-lynx", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-orion.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-orion.dts
new file mode 100644
index 000000000000..884b236746bb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-orion.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2020 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Orion i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-orion", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&uart2 {
+	status = "disabled";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-phoenix.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-phoenix.dts
new file mode 100644
index 000000000000..e0292f11d03e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-phoenix.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Phoenix i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-phoenix", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
+
+&aliases {
+	/delete-property/ ethernet1;
+};
+
+&gpio_keys {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&switch_ports {
+	/delete-node/ port@2;
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-ursa.dts
index 0d594e4bd559..f6ae24efd4aa 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-ursa.dts
@@ -17,6 +17,10 @@
 	};
 };
 
+&aliases {
+	/delete-property/ ethernet1;
+};
+
 &backlight {
 	status = "okay";
 };
@@ -38,7 +42,7 @@
 };
 
 &switch_ports {
-	/delete-node/ port@2;
+	/delete-node/ port@3;
 };
 
 &touchscreen {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp43-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp43-common.dtsi
new file mode 100644
index 000000000000..52a0f6ee426f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp43-common.dtsi
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases: aliases {
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 32 64 128 255>;
+		default-brightness-level = <32>;
+		num-interpolated-steps = <8>;
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		button {
+			label = "Factory RESET";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	lcd_display: display {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel: panel {
+		compatible = "dataimage,scf0700c48ggu18";
+		power-supply = <&sw2_reg>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&sw2_reg>;
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@0 {
+			compatible = "marvell,mv88e6085";
+			reg = <0>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+
+			switch_ports: ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethphy0: port@0 {
+					reg = <0>;
+					label = "cpu";
+					phy-mode = "rgmii-id";
+					ethernet = <&fec>;
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				eth2: port@1 {
+					reg = <1>;
+					label = "eth2";
+					phy-handle = <&phy_port1>;
+				};
+
+				eth1: port@2 {
+					reg = <2>;
+					label = "eth1";
+					phy-handle = <&phy_port2>;
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_port1: switchphy@11 {
+					reg = <0x11>;
+				};
+
+				phy_port2: switchphy@12 {
+					reg = <0x12>;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze200";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x8>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vsnvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	leds: led-controller@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		clock-mode = /bits/ 8 <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		led@0 {
+			chan-name = "R";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+			reg = <0>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@1 {
+			chan-name = "G";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@2 {
+			chan-name = "B";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+			reg = <2>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <64>;
+	};
+
+	touchscreen: touchscreen@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		reg = <0x5c>;
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		status = "disabled";
+	};
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1341";
+		reg = <0x68>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "disabled";
+
+	oled_1309: oled@3c {
+		compatible = "solomon,ssd1309fb-i2c";
+		reg = <0x3c>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,segment-no-remap;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	oled_1305: oled@3d {
+		compatible = "solomon,ssd1305fb-i2c";
+		reg = <0x3d>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,col-offset = <4>;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_oled: gpio@41 {
+		compatible = "nxp,pca9536";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x41>;
+		vcc-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	touchkeys: keys@5a {
+		compatible = "fsl,mpr121-touchkey";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchkeys>;
+		reg = <0x5a>;
+		vdd-supply = <&sw2_reg>;
+		autorepeat;
+		linux,keycodes = <KEY_1>, <KEY_2>, <KEY_3>, <KEY_4>, <KEY_5>,
+				<KEY_6>, <KEY_7>, <KEY_8>, <KEY_9>,
+				<KEY_BACKSPACE>, <KEY_0>, <KEY_ENTER>;
+		poll-interval = <50>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b020
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b020
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b020
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b020
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b020
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b020
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b020
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b020
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b020
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b020
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b020
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b020
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b020
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b010
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b010
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b098
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07                  0x1b0b0
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b098
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x8
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b098
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b098
+		>;
+	};
+
+	pinctrl_touchkeys: touchkeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b098
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x1b098
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0a8
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0a8
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__UART2_TX_DATA	0x1b098
+			MX6QDL_PAD_GPIO_8__UART2_RX_DATA	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__USB_H1_OC	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b098
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b098
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotg-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD	0x1f069
+			MX6QDL_PAD_SD4_CLK__SD4_CLK	0x10069
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0	0x17069
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1	0x17069
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2	0x17069
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3	0x17069
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4	0x17069
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5	0x17069
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6	0x17069
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7	0x17069
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B	0x1b0b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "disabled";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	over-current-active-low;
+	status = "disabled";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	over-current-active-low;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+	status = "okay";
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <109>;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	vmmc-supply = <&sw2_reg>;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl.dtsi
index 008312ee0c31..dc919e09a505 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl.dtsi
@@ -44,6 +44,8 @@
 			arm-supply = <&reg_arm>;
 			pu-supply = <&reg_pu>;
 			soc-supply = <&reg_soc>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		cpu@1 {
@@ -78,18 +80,17 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-		aips1: aips-bus@2000000 {
-			iomuxc: iomuxc@20e0000 {
-				compatible = "fsl,imx6dl-iomuxc";
-			};
-
+		aips1: bus@2000000 {
 			pxp: pxp@20f0000 {
 				reg = <0x020f0000 0x4000>;
 				interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
@@ -101,7 +102,7 @@
 			};
 		};
 
-		aips2: aips-bus@2100000 {
+		aips2: bus@2100000 {
 			i2c4: i2c@21f8000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -296,6 +297,10 @@
 	compatible = "fsl,imx6dl-hdmi";
 };
 
+&iomuxc {
+	compatible = "fsl,imx6dl-iomuxc";
+};
+
 &ipu1_csi1 {
 	ipu1_csi1_from_ipu1_csi1_mux: endpoint {
 		remote-endpoint = <&ipu1_csi1_mux_to_ipu1_csi1>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
new file mode 100644
index 000000000000..3fc079dfd61e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
+	compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_pcie_switch: regulator-pcie-switch {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "pcie_switch";
+		startup-delay-us = <100000>;
+		status = "okay";
+	};
+
+	reg_3v3_sw: regulator-3v3-sw {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SW";
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_3v3_sw>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_3v3_sw>;
+	status = "okay";
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
+&i2c1 {
+	status = "okay";
+
+	pcie-switch@58 {
+		compatible = "plx,pex8605";
+		reg = <0x58>;
+	};
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+	vpcie-supply = <&reg_pcie_switch>;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sound_spdif {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.1.dts
new file mode 100644
index 000000000000..44637d606e61
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.1.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+#include "imx6q-apalis-ixora-v1.2.dts"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.1";
+	compatible = "toradex,apalis_imx6q-ixora-v1.1", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+
+};
+
+/delete-node/ &eeprom;
+/delete-node/ &reg_3v3_vmmc;
+/delete-node/ &reg_can1_supply;
+/delete-node/ &reg_can2_supply;
+
+&can1 {
+	/delete-property/ xceiver-supply;
+};
+
+&can2 {
+	/delete-property/ xceiver-supply;
+};
+
+/* MMC1 */
+&usdhc1 {
+	/delete-property/ cap-power-off-card;
+	/delete-property/ pinctrl-1;
+	/delete-property/ vmmc-supply;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.2.dts
new file mode 100644
index 000000000000..3ac7a4501620
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.2.dts
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.2";
+	compatible = "toradex,apalis_imx6q-ixora-v1.2", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_ixora>;
+
+		led4-green {
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_GREEN";
+		};
+
+		led4-red {
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_RED";
+		};
+
+		led5-green {
+			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_GREEN";
+		};
+
+		led5-red {
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_RED";
+		};
+	};
+
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+
+	reg_can1_supply: regulator-can1-supply {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can1_power>;
+		regulator-name = "can1_supply";
+		startup-delay-us = <1000>;
+	};
+
+	reg_can2_supply: regulator-can2-supply {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can2_power>;
+		regulator-name = "can2_supply";
+		startup-delay-us = <1000>;
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_can1_supply>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_can2_supply>;
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart24_forceoff>;
+
+	/*
+	 * uart-2-4-on-x21-enable-hog enables the UART transceiver for Apalis
+	 * UART2 and UART3. If one wants to disable the transceiver force
+	 * the GPIO to output-low, if one wants to control the transceiver
+	 * from user space delete the hog node.
+	 */
+	uart-2-4-on-x21-enable-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* MXM3 180 */
+		output-high;
+	};
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
+&i2c1 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sound_spdif {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_4bit_sleep &pinctrl_mmc_cd_sleep>;
+	bus-width = <4>;
+	cap-power-off-card;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can1_power: enablecan1powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can2_power: enablecan2powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b0
+		>;
+	};
+
+	pinctrl_uart24_forceoff: uart24forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x1b0b0
+		>;
+	};
+
+	pinctrl_leds_ixora: ledsixoragrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+		>;
+	};
+
+	pinctrl_mmc_cd_sleep: mmccdslpgrp {
+		fsl,pins = <
+			 /* MMC1 CD */
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0
+		>;
+	};
+
+	pinctrl_usdhc1_4bit_sleep: usdhc1-4bitslpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD     0x3000
+			MX6QDL_PAD_SD1_CLK__SD1_CLK     0x3000
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0  0x3000
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1  0x3000
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2  0x3000
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3  0x3000
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora.dts
new file mode 100644
index 000000000000..f338be435277
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board";
+	compatible = "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_ixora>;
+
+		led4-green {
+			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_GREEN";
+		};
+
+		led4-red {
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_RED";
+		};
+
+		led5-green {
+			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_GREEN";
+		};
+
+		led5-red {
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_RED";
+		};
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
+&i2c1 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sound_spdif {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_leds_ixora: ledsixoragrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-apf6dev.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apf6dev.dts
index 664b0af8f0bb..664b0af8f0bb 100644
--- a/arch/arm/boot/dts/imx6q-apf6dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apf6dev.dts
diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-arm2.dts
index 0b40f52268b3..631d6d690959 100644
--- a/arch/arm/boot/dts/imx6q-arm2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-arm2.dts
@@ -17,29 +17,21 @@
 		reg = <0x10000000 0x80000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
 	};
 
 	leds {
@@ -178,6 +170,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-b450v3.dts b/arch/arm/boot/dts/nxp/imx/imx6q-b450v3.dts
index 95b8f2d71821..d994b32ad825 100644
--- a/arch/arm/boot/dts/imx6q-b450v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-b450v3.dts
@@ -65,13 +65,6 @@
 	};
 };
 
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
 &ldb {
 	status = "okay";
 
@@ -91,19 +84,24 @@
 };
 
 &pca9539 {
-	P04 {
+	gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN",
+			  "", "SM_D_ACT", "DP1_RST#", "",
+			  "WD15S_EN", "WD15S_DIS#", "", "",
+			  "", "", "", "";
+
+	P04-hog {
 		gpio-hog;
 		gpios = <4 0>;
 		output-low;
 		line-name = "PCA9539-P04";
 	};
 
-        P07 {
-                gpio-hog;
-                gpios = <7 0>;
-                output-low;
-                line-name = "PCA9539-P07";
-        };
+	P07-hog {
+		gpio-hog;
+		gpios = <7 0>;
+		output-low;
+		line-name = "PCA9539-P07";
+	};
 };
 
 &pci_root {
diff --git a/arch/arm/boot/dts/imx6q-b650v3.dts b/arch/arm/boot/dts/nxp/imx/imx6q-b650v3.dts
index 611cb7ae7e55..b0d345f5d071 100644
--- a/arch/arm/boot/dts/imx6q-b650v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-b650v3.dts
@@ -65,13 +65,6 @@
 	};
 };
 
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
 &ldb {
 	status = "okay";
 
@@ -91,17 +84,22 @@
 };
 
 &pca9539 {
-        P07 {
-                gpio-hog;
-                gpios = <7 0>;
-                output-low;
-                line-name = "PCA9539-P07";
-        };
+	gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN",
+			  "", "SM_D_ACT", "DP1_RST#", "",
+			  "WD15S_EN", "WD15S_DIS#", "", "",
+			  "", "", "", "";
+
+	P07-hog {
+		gpio-hog;
+		gpios = <7 0>;
+		output-low;
+		line-name = "PCA9539-P07";
+	};
 };
 
 &usbphy1 {
-	fsl,tx-cal-45-dn-ohms = <55>;
-	fsl,tx-cal-45-dp-ohms = <55>;
+	fsl,tx-cal-45-dn-ohms = <54>;
+	fsl,tx-cal-45-dp-ohms = <54>;
 	fsl,tx-d-cal = <100>;
 };
 
diff --git a/arch/arm/boot/dts/imx6q-b850v3.dts b/arch/arm/boot/dts/nxp/imx/imx6q-b850v3.dts
index e4cb118f88c6..db8c332df6a1 100644
--- a/arch/arm/boot/dts/imx6q-b850v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-b850v3.dts
@@ -53,17 +53,6 @@
 	};
 };
 
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
-			  <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
-			  <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
-				 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
-				 <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
-				 <&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
-};
-
 &ldb {
 	fsl,dual-channel;
 	status = "okay";
@@ -210,14 +199,19 @@
 };
 
 &pca9539 {
-	P10 {
+	gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN",
+			  "REMOTE_ON_PML#", "SM_D_ACT", "DP1_RST#", "DP2_RST#",
+			  "", "", "", "",
+			  "", "", "", "";
+
+	P10-hog {
 		gpio-hog;
 		gpios = <8 0>;
 		output-low;
 		line-name = "PCA9539-P10";
 	};
 
-	P11 {
+	P11-hog {
 		gpio-hog;
 		gpios = <9 0>;
 		output-low;
diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
index 37c63402157b..f266f1b7e0cf 100644
--- a/arch/arm/boot/dts/imx6q-ba16.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
@@ -124,6 +124,9 @@
 		regulator-name = "usb_otg_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 };
 
@@ -134,12 +137,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: n25q032@0 {
+	flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -172,7 +175,19 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
+	phy-supply = <&reg_3p3v>;
+	phy-handle = <&phy0>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
 };
 
 &hdmi {
@@ -334,6 +349,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -574,6 +590,12 @@
 		>;
 	};
 
+	pinctrl_usbotg_vbus: usbotgvbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+		>;
+	};
+
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD2_CMD__SD2_CMD	0x17059
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
new file mode 100644
index 000000000000..02648806c275
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
@@ -0,0 +1,777 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Support for the i.MX6-based Bosch ACC board.
+ *
+ * Copyright (C) 2016 Garz & Fricke GmbH
+ * Copyright (C) 2018 DENX Software Engineering GmbH, Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2018 DENX Software Engineering GmbH, Niel Fourie <lusus@denx.de>
+ * Copyright (C) 2019-2021 Bosch Thermotechnik GmbH, Matthias Winker <matthias.winker@bosch.com>
+ * Copyright (C) 2022 DENX Software Engineering GmbH, Philip Oberfichtner <pro@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6q.dtsi"
+
+/ {
+	model = "Bosch ACC";
+	compatible = "bosch,imx6q-acc", "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+		serial0 = &uart2;
+		serial1 = &uart1;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 200000>;
+		brightness-levels = <0 61 499 1706 4079 8022 13938 22237 33328 47623 65535>;
+		num-interpolated-steps = <10>;
+		default-brightness-level = <60>;
+		power-supply = <&reg_lcd>;
+	};
+
+	panel {
+		compatible = "dataimage,fg1001l0dsswmg01";
+		backlight = <&backlight_lvds>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	refclk: refclk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-div = <1>;
+		clock-mult = <1>;
+		clock-output-names = "12mhz_refclk";
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO2>,
+				  <&clks IMX6QDL_CLK_CKO2_SEL>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>,
+					 <&clks IMX6QDL_CLK_CKO2_PODF>,
+					 <&clks IMX6QDL_CLK_OSC>;
+		assigned-clock-rates = <0>, <12000000>, <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				1200000 1275000
+				996000  1225000
+				852000  1225000
+				792000  1150000
+				396000  950000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz  SOC-PU uV */
+				1200000 1225000
+				996000	1175000
+				852000	1175000
+				792000	1150000
+				396000	1150000
+			>;
+		};
+
+		cpu1: cpu@1 {
+			operating-points = <
+				/* kHz    uV */
+				1200000 1275000
+				996000  1225000
+				852000  1225000
+				792000  1150000
+				396000  950000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz  SOC-PU uV */
+				1200000 1225000
+				996000	1175000
+				852000	1175000
+				792000	1150000
+				396000	1150000
+			>;
+		};
+	};
+
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led_red: led-0 {
+			color = <LED_COLOR_ID_RED>;
+			max-brightness = <248>;
+			default-state = "off";
+			pwms = <&pwm2 0 500000>;
+		};
+
+		led_white: led-1 {
+			color = <LED_COLOR_ID_WHITE>;
+			max-brightness = <248>;
+			default-state = "off";
+			pwms = <&pwm3 0 500000>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reset_gpio_led>;
+
+		led-2 {
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_5p0: regulator-5p0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5p0";
+	};
+
+	reg_vin: regulator-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "VIN";
+		regulator-min-microvolt = <4500000>;
+		regulator-max-microvolt = <4500000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_usb_h2_vbus: regulator-usb-h2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5p0> ;
+		regulator-always-on;
+	};
+
+	reg_vsnvs: regulator-vsnvs {
+		compatible = "regulator-fixed";
+		regulator-name = "VSNVS_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD0 POWER";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd_enable>;
+		gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_dac: regulator-dac {
+		compatible = "regulator-fixed";
+		regulator-name = "vref_dac";
+		regulator-min-microvolt = <20000>;
+		regulator-max-microvolt = <20000>;
+		vin-supply = <&reg_5p0> ;
+		regulator-boot-on;
+	};
+
+	reg_sw4: regulator-sw4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SW4_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_sys: regulator-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "SYS_4V2";
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+};
+
+&reg_arm {
+	vin-supply = <&sw2_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&reg_vdd3p0 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
+	phy-mode = "rmii";
+	phy-supply = <&reg_sw4>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpu_vg {
+	status = "disabled";
+};
+
+&gpu_2d {
+	status = "disabled";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pmic: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1c_reg: sw1c {
+				regulator-name = "VDD_SOC (sw1abc)";
+				regulator-min-microvolt = <1275000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "VDD_ARM (sw2)";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-name = "DDR_1V5a";
+				regulator-boot-on;
+				regulator-always-on;
+
+			};
+
+			sw3b_reg: sw3b {
+				regulator-name = "DDR_1V5b";
+				regulator-boot-on;
+				regulator-always-on;
+
+			};
+
+			sw4_reg: sw4 {
+				regulator-name = "AUX 3V15 (sw4)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+				regulator-always-on;
+				status = "disabled";
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lm75: sensor@49 {
+		compatible = "national,lm75b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lm75>;
+		reg = <0x49>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@51 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	eeprom_ext: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	usb3503: usb@8 {
+		compatible = "smsc,usb3503";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb3503>;
+		reg = <0x08>;
+		connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
+		intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
+		reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
+		initial-mode = <1>;
+		clocks = <&refclk>;
+		clock-names = "refclk";
+		refclk-frequency = <12000000>;
+	};
+
+	exc3000: touchscreen@2a {
+		compatible = "eeti,exc3000";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctouch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-size-x = <4096>;
+		touchscreen-size-y = <4096>;
+	};
+
+	vcnl4035: light-sensor@60 {
+		compatible = "vishay,vcnl4035";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_proximity>;
+		reg = <0x60>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	rts-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbh2 {
+	pinctrl-names = "idle", "active";
+	pinctrl-0 = <&pinctrl_usbh2_idle>;
+	pinctrl-1 = <&pinctrl_usbh2_active>;
+	vbus-supply = <&reg_usb_h2_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	disable-over-current;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphynop1 {
+	clocks = <&clks IMX6QDL_CLK_USBPHY1>;
+	clock-names = "main_clk";
+	vcc-supply = <&reg_usb_h1_vbus>;
+};
+
+&usbphynop2 {
+	vcc-supply = <&reg_usb_h2_vbus>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	voltage-ranges = <3300 3300>;
+	vmmc-supply = <&reg_sw4>;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	voltage-ranges = <3300 3300>;
+	vmmc-supply = <&reg_sw4>;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+	timeout-sec = <10>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b0	/* FEC INT */
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x0001b098
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x0001b098
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x0001b098
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_reset_gpio_led: reset-gpio-led-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b810
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b810
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL  0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_lcd_enable: lcdenablegrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23  0x1b0b0 /* lcd enable */
+			MX6QDL_PAD_EIM_D16__GPIO3_IO16  0x1b0b0 /* sel6_8 */
+		>;
+	};
+
+	pinctrl_lm75: lm75grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_proximity: proximitygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11  0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_rtc: rtc-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0 /* RTC INT */
+		>;
+	};
+
+	pinctrl_ctouch: ctouch-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 /* CTOUCH_INT */
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x0001b0b0 /* CTOUCH_RESET */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x0001b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh2_idle: usbh2-idle-grp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TXC__USB_H2_DATA      0x00013018
+			MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00013018
+		>;
+	};
+
+	pinctrl_usbh2_active: usbh2-active-grp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TXC__USB_H2_DATA      0x00013018
+			MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00017018
+		>;
+	};
+
+	pinctrl_usb3503: usb3503-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1    0x00000018
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12     0x1b0b0 /* USB INT */
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x0001b0b0 /* USB Reset */
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16    0x1b0b0 /* USB Connect */
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x00017069
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x00010038
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017069
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017069
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017069
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017069
+			MX6QDL_PAD_GPIO_4__SD2_CD_B    0x0001b0b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD    0x00017059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK    0x00010059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x00017059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x00017059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x00017059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x00017059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x00017059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x00017059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x00017059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x00017059
+		>;
+	};
+
+	pinctrl_wdog1: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-bx50v3.dtsi
index fa27dcdf06f1..99f4f6ac71d4 100644
--- a/arch/arm/boot/dts/imx6q-bx50v3.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-bx50v3.dtsi
@@ -102,10 +102,15 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		switch@0 {
+		switch: switch@0 {
 			compatible = "marvell,mv88e6085"; /* 88e6240*/
 			reg = <0>;
 
+			interrupt-parent = <&gpio2>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
 			switch_ports: ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -117,22 +122,32 @@
 
 				switchphy0: switchphy@0 {
 					reg = <0>;
+					interrupt-parent = <&switch>;
+					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
 				switchphy1: switchphy@1 {
 					reg = <1>;
+					interrupt-parent = <&switch>;
+					interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
 				switchphy2: switchphy@2 {
 					reg = <2>;
+					interrupt-parent = <&switch>;
+					interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
 				switchphy3: switchphy@3 {
 					reg = <3>;
+					interrupt-parent = <&switch>;
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
 				switchphy4: switchphy@4 {
 					reg = <4>;
+					interrupt-parent = <&switch>;
+					interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
 				};
 			};
 		};
@@ -140,12 +155,12 @@
 };
 
 &ecspi5 {
-	cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: flash@0 {
 		compatible = "atmel,at25";
 		spi-max-frequency = <10000000>;
 		size = <0x8000>;
@@ -158,8 +173,8 @@
 &i2c1 {
 	pinctrl-names = "default", "gpio";
 	pinctrl-1 = <&pinctrl_i2c1_gpio>;
-	sda-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
-	scl-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 
 	pca9547: mux@70 {
 		compatible = "nxp,pca9547";
@@ -213,6 +228,7 @@
 			sgtl5000: codec@a {
 				compatible = "fsl,sgtl5000";
 				reg = <0x0a>;
+				#sound-dai-cells = <0>;
 				clocks = <&mclk>;
 				VDDA-supply = <&reg_1p8v>;
 				VDDIO-supply = <&reg_3p3v>;
@@ -233,42 +249,42 @@
 				interrupt-parent = <&gpio2>;
 				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 
-				P12 {
+				P12-hog {
 					gpio-hog;
 					gpios = <10 0>;
 					output-low;
 					line-name = "PCA9539-P12";
 				};
 
-				P13 {
+				P13-hog {
 					gpio-hog;
 					gpios = <11 0>;
 					output-low;
 					line-name = "PCA9539-P13";
 				};
 
-				P14 {
+				P14-hog {
 					gpio-hog;
 					gpios = <12 0>;
 					output-low;
 					line-name = "PCA9539-P14";
 				};
 
-				P15 {
+				P15-hog {
 					gpio-hog;
 					gpios = <13 0>;
 					output-low;
 					line-name = "PCA9539-P15";
 				};
 
-				P16 {
+				P16-hog {
 					gpio-hog;
 					gpios = <14 0>;
 					output-low;
 					line-name = "PCA9539-P16";
 				};
 
-				P17 {
+				P17-hog {
 					gpio-hog;
 					gpios = <15 0>;
 					output-low;
@@ -300,15 +316,15 @@
 &i2c2 {
 	pinctrl-names = "default", "gpio";
 	pinctrl-1 = <&pinctrl_i2c2_gpio>;
-	sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
-	scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 };
 
 &i2c3 {
 	pinctrl-names = "default", "gpio";
 	pinctrl-1 = <&pinctrl_i2c3_gpio>;
-	sda-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
-	scl-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 };
 
 &iomuxc {
@@ -377,3 +393,18 @@
 		#interrupt-cells = <1>;
 	};
 };
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+			  <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
+			  <&clks IMX6QDL_CLK_IPU1_DI1_PRE_SEL>,
+			  <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>,
+			  <&clks IMX6QDL_CLK_IPU2_DI1_PRE_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+				 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+				 <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+				 <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+				 <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+				 <&clks IMX6QDL_CLK_PLL2_PFD0_352M>;
+};
diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cm-fx6.dts
index cab9e92531c7..95b49fc83f7b 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cm-fx6.dts
@@ -141,7 +141,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_RCLKDIR |
@@ -152,7 +152,7 @@
 		>;
 	};
 
-	audmux4 {
+	mux-audmux4 {
 		fsl,audmux-port = <3>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -255,15 +255,15 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "st,m25p", "jedec,spi-nor";
+		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
 	};
diff --git a/arch/arm/boot/dts/imx6q-cubox-i-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-emmc-som-v15.dts
index 3e59ebbb3608..3e59ebbb3608 100644
--- a/arch/arm/boot/dts/imx6q-cubox-i-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-cubox-i-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-som-v15.dts
index dab70d1230a2..dab70d1230a2 100644
--- a/arch/arm/boot/dts/imx6q-cubox-i-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-cubox-i.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i.dts
index 1c7b262e3709..1c7b262e3709 100644
--- a/arch/arm/boot/dts/imx6q-cubox-i.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i.dts
diff --git a/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dfi-fs700-m60.dts
index 8bfe6337cd65..8bfe6337cd65 100644
--- a/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dfi-fs700-m60.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dhcom-pdk2.dts
new file mode 100644
index 000000000000..d4d57370615d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dhcom-pdk2.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2021 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM iMX6 variant:
+ * DHCM-iMX6Q-C0800-R102-F0819-E-SD-RTC-T-HS-I-01D2
+ * DHCOM PCB number: 493-300 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-dhcom-som.dtsi"
+#include "imx6qdl-dhcom-pdk2.dtsi"
+
+/ {
+	model = "DH electronics i.MX6Q DHCOM on Premium Developer Kit (2)";
+	compatible = "dh,imx6q-dhcom-pdk2", "dh,imx6q-dhcom-som",
+		     "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/nxp/imx/imx6q-display5-tianma-tm070-1280x768.dts
index 16658b76fc4e..16658b76fc4e 100644
--- a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-display5-tianma-tm070-1280x768.dts
diff --git a/arch/arm/boot/dts/imx6q-display5.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-display5.dtsi
index 83524bb99eb3..4ab31f2217cd 100644
--- a/arch/arm/boot/dts/imx6q-display5.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-display5.dtsi
@@ -147,7 +147,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -159,7 +159,7 @@
 		>;
 	};
 
-	aud6 {
+	mux-aud6 {
 		fsl,audmux-port = <5>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_RFSEL(8) |
@@ -276,7 +276,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	at24@50 {
+	eeprom@50 {
 		compatible = "atmel,24c256";
 		pagesize = <64>;
 		reg = <0x50>;
@@ -399,7 +399,6 @@
 };
 
 &pwm2 {
-	#pwm-cells = <3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dts
index f9df207b2778..9f7ac7158c46 100644
--- a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dts
@@ -28,40 +28,31 @@
 		reg = <0x10000000 0x80000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_switch: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg_switch";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio7 12 0>;
-			regulator-boot-on;
-			regulator-always-on;
-		};
+	reg_usb_otg_switch: regulator-usb-otg-switch {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_switch";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 12 0>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 
-		reg_usb_host1: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_host1_en";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 31 0>;
-			enable-active-high;
-		};
+	reg_usb_host1: regulator-usb-host1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_host1_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 31 0>;
+		enable-active-high;
 	};
 
 	gpio-leds {
@@ -99,10 +90,10 @@
 &ecspi5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi5>;
-	cs-gpios = <&gpio1 12 0>;
+	cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80", "jedec,spi-nor";
 		spi-max-frequency = <40000000>;
 		reg = <0>;
@@ -112,7 +103,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	phy-supply = <&vgen2_1v2_eth>;
 	status = "okay";
@@ -134,7 +125,7 @@
 		     &pinctrl_pfuze>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 		interrupt-parent = <&gpio3>;
diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dms-ba16.dts
index 57761f3172fa..d2d0a82ea178 100644
--- a/arch/arm/boot/dts/imx6q-dms-ba16.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dms-ba16.dts
@@ -42,12 +42,12 @@
 };
 
 &ecspi5 {
-	cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: flash@0 {
 		compatible = "atmel,at25256B", "atmel,at25";
 		spi-max-frequency = <20000000>;
 		size = <0x8000>;
@@ -96,6 +96,7 @@
 	sgtl5000: codec@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		lrclk-strength = <0x3>;
 		VDDA-supply = <&reg_1p8v>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-ds.dts b/arch/arm/boot/dts/nxp/imx/imx6q-ds.dts
new file mode 100644
index 000000000000..b0a63a133977
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ds.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
+//
+// Based on imx6qdl-sabresd.dtsi which is:
+// Copyright 2012 Freescale Semiconductor, Inc.
+// Copyright 2011 Linaro Ltd.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-ds.dtsi"
+
+/ {
+	model = "DaSheng i.MX6 Quad Com-9xx Board";
+	compatible = "ds,imx6q-sbc", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-emcon-avari.dts b/arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dts
index 0f582a9d4c0e..02813368a820 100644
--- a/arch/arm/boot/dts/imx6q-emcon-avari.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/nxp/imx/imx6q-evi.dts
index c63f371ede8b..78d941fef5df 100644
--- a/arch/arm/boot/dts/imx6q-evi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-evi.dts
@@ -146,6 +146,7 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-gk802.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gk802.dts
index ccc2487d47ca..ce55c9558679 100644
--- a/arch/arm/boot/dts/imx6q-gk802.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gk802.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2013 Philipp Zabel
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Philipp Zabel
 
 /dts-v1/;
 #include <dt-bindings/gpio/gpio.h>
@@ -24,19 +19,12 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	gpio-keys {
diff --git a/arch/arm/boot/dts/imx6q-gw51xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw51xx.dts
index f80173458e3f..f80173458e3f 100644
--- a/arch/arm/boot/dts/imx6q-gw51xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw51xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw52xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw52xx.dts
index 6e1c493c9c8c..6e1c493c9c8c 100644
--- a/arch/arm/boot/dts/imx6q-gw52xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw52xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw53xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw53xx.dts
index f13df8e9c8c4..f13df8e9c8c4 100644
--- a/arch/arm/boot/dts/imx6q-gw53xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw53xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5400-a.dts
index b6e2b580051d..c5c144879fa6 100644
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5400-a.dts
@@ -34,20 +34,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 -> MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* 106 -> MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* 111 -> MX6_LOCLED# */
 			default-state = "off";
@@ -67,47 +67,37 @@
 		status = "okay";
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_1p0v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "1P0V";
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-			regulator-always-on;
-		};
+	reg_1p0v: regulator-1p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P0V";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_h1_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
@@ -132,12 +122,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,w25q256", "jedec,spi-nor";
 		spi-max-frequency = <30000000>;
 		reg = <0>;
@@ -206,7 +196,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -320,6 +310,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&sw4_reg>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6q-gw54xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw54xx.dts
index d5d46908cf6e..d5d46908cf6e 100644
--- a/arch/arm/boot/dts/imx6q-gw54xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw54xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw551x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw551x.dts
index 2c7feeef1b0e..2c7feeef1b0e 100644
--- a/arch/arm/boot/dts/imx6q-gw551x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw551x.dts
diff --git a/arch/arm/boot/dts/imx6q-gw552x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw552x.dts
index c973b7304225..c973b7304225 100644
--- a/arch/arm/boot/dts/imx6q-gw552x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw552x.dts
diff --git a/arch/arm/boot/dts/imx6q-gw553x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw553x.dts
index e9c224cea752..e9c224cea752 100644
--- a/arch/arm/boot/dts/imx6q-gw553x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw553x.dts
diff --git a/arch/arm/boot/dts/imx6q-gw560x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw560x.dts
index 735f2bbf1439..735f2bbf1439 100644
--- a/arch/arm/boot/dts/imx6q-gw560x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw560x.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5903.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5903.dts
index a182e4cb0e6e..a182e4cb0e6e 100644
--- a/arch/arm/boot/dts/imx6q-gw5903.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5903.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5904.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5904.dts
index ca1e2ae3341e..ca1e2ae3341e 100644
--- a/arch/arm/boot/dts/imx6q-gw5904.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5904.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw5907.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5907.dts
new file mode 100644
index 000000000000..b25526ef5886
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5907.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5907.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW5907";
+	compatible = "gw,imx6q-gw5907", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw5910.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5910.dts
new file mode 100644
index 000000000000..6aafa2fcee08
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5910.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5910.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW5910";
+	compatible = "gw,imx6q-gw5910", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw5912.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5912.dts
new file mode 100644
index 000000000000..4dcbd943cd93
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5912.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5912.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW5912";
+	compatible = "gw,imx6q-gw5912", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw5913.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5913.dts
new file mode 100644
index 000000000000..6f511f1665fd
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5913.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5913.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW5913";
+	compatible = "gw,imx6q-gw5913", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-h100.dts b/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts
index b8feadbff967..a603562ea49a 100644
--- a/arch/arm/boot/dts/imx6q-h100.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts
@@ -76,19 +76,19 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_h100_leds>;
 
-		led0: power {
+		led0: led-power {
 			label = "power";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		led1: stream {
+		led1: led-stream {
 			label = "stream";
 			gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		led2: rec {
+		led2: led-rec {
 			label = "rec";
 			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -166,7 +166,7 @@
 	pinctrl-0 = <&pinctrl_h100_i2c1>;
 	status = "okay";
 
-	eeprom: 24c02@51 {
+	eeprom: eeprom@51 {
 		compatible = "microchip,24c02", "atmel,24c02";
 		reg = <0x51>;
 	};
@@ -179,6 +179,7 @@
 	sgtl5000: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_h100_sgtl5000>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
diff --git a/arch/arm/boot/dts/imx6q-hummingboard-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-emmc-som-v15.dts
index c51b4e4fd71e..c51b4e4fd71e 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-som-v15.dts
index e4132d62ffa2..e4132d62ffa2 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard.dts
index 8c9e94e648a7..8c9e94e648a7 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard2-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-emmc-som-v15.dts
index 1998ebfa0fe0..1998ebfa0fe0 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard2-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard2-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-som-v15.dts
index d3ad7329cd6d..d3ad7329cd6d 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard2-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2.dts
index 5249f53dcdbc..5249f53dcdbc 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-mipi.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-mipi.dts
index d51745268dbf..d51745268dbf 100644
--- a/arch/arm/boot/dts/imx6q-icore-mipi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-mipi.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap10.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap10.dts
index 81cc346dd149..02aca1e28ce3 100644
--- a/arch/arm/boot/dts/imx6q-icore-ofcap10.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap10.dts
@@ -12,6 +12,17 @@
 / {
 	model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 10.1 Kit";
 	compatible = "engicam,imx6-icore", "fsl,imx6q";
+
+	panel {
+		compatible = "ampire,am-1280800n3tzqw-t00h";
+		backlight = <&backlight_lvds>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
 };
 
 &ldb {
@@ -22,18 +33,11 @@
 		fsl,data-width = <24>;
 		status = "okay";
 
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: timing0 {
-				clock-frequency = <60000000>;
-				hactive = <1280>;
-				vactive = <800>;
-				hback-porch = <40>;
-				hfront-porch = <40>;
-				vback-porch = <10>;
-				vfront-porch = <3>;
-				hsync-len = <80>;
-				vsync-len = <10>;
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap12.dts
index 241811c52b62..241811c52b62 100644
--- a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap12.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-rqs.dts
index cf6ba724f497..cf6ba724f497 100644
--- a/arch/arm/boot/dts/imx6q-icore-rqs.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-rqs.dts
diff --git a/arch/arm/boot/dts/imx6q-icore.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore.dts
index fe28c3cf54c0..fe28c3cf54c0 100644
--- a/arch/arm/boot/dts/imx6q-icore.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore.dts
diff --git a/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i.dtsi
index 2618eccfe50d..4d6a0c3e8455 100644
--- a/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i.dtsi
@@ -14,10 +14,9 @@
 
 /* Quad/Dual SoMs have 3 chip-select signals */
 &ecspi4 {
-	fsl,spi-num-chipselects = <3>;
-	cs-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>,
-		   <&gpio3 29 GPIO_ACTIVE_HIGH>,
-		   <&gpio3 25 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>,
+		   <&gpio3 29 GPIO_ACTIVE_LOW>,
+		   <&gpio3 25 GPIO_ACTIVE_LOW>;
 };
 
 &pinctrl_ecspi4 {
diff --git a/arch/arm/boot/dts/imx6q-kp-tpc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-kp-tpc.dts
index 50fbf46d17c2..50fbf46d17c2 100644
--- a/arch/arm/boot/dts/imx6q-kp-tpc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kp-tpc.dts
diff --git a/arch/arm/boot/dts/imx6q-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
index 24c8169baf44..091903f53a56 100644
--- a/arch/arm/boot/dts/imx6q-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
@@ -66,14 +66,14 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-green {
 			label = "led1";
 			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "gpio";
 			default-state = "off";
 		};
 
-		red {
+		led-red {
 			label = "led0";
 			gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "gpio";
@@ -135,7 +135,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -147,7 +147,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -378,12 +378,14 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6q-logicpd.dts b/arch/arm/boot/dts/nxp/imx/imx6q-logicpd.dts
index d96ae54be338..46a4ddedb423 100644
--- a/arch/arm/boot/dts/imx6q-logicpd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-logicpd.dts
@@ -9,11 +9,11 @@
 
 / {
 	model = "Logic PD i.MX6QD SOM-M3";
-	compatible = "fsl,imx6q";
+	compatible = "logicpd,imx6q-logicpd", "fsl,imx6q";
 
 	backlight: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 20000>;
+		pwms = <&pwm3 0 20000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		power-supply = <&reg_lcd>;
@@ -73,6 +73,16 @@
 	status = "okay";
 };
 
+&i2c1 {
+	touchscreen@26 {
+		compatible = "ilitek,ili2117";
+		reg = <0x26>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupts-extended = <&gpio1 6 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
 &ldb {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6q-marsboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-marsboard.dts
index 84b30bd6908f..2c9961333b0a 100644
--- a/arch/arm/boot/dts/imx6q-marsboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-marsboard.dts
@@ -73,14 +73,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user1 {
+		led-user1 {
 			label = "imx6:green:user1";
 			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
 		};
 
-		user2 {
+		led-user2 {
 			label = "imx6:green:user2";
 			gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -100,7 +100,7 @@
 	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -111,8 +111,22 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
+	phy-handle = <&rgmii_phy>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Atheros AR8035 PHY */
+		rgmii_phy: ethernet-phy@4 {
+			reg = <4>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <1000>;
+		};
+	};
 };
 
 &hdmi {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-mba6.dtsi
new file mode 100644
index 000000000000..0d7be4567291
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mba6.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&ecspi5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi5_mba6x>;
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+};
+
+&ethphy {
+	rxdv-skew-ps = <180>;
+	txen-skew-ps = <120>;
+	rxd3-skew-ps = <180>;
+	rxd2-skew-ps = <180>;
+	rxd1-skew-ps = <180>;
+	rxd0-skew-ps = <180>;
+	txd3-skew-ps = <120>;
+	txd2-skew-ps = <0>;
+	txd1-skew-ps = <180>;
+	txd0-skew-ps = <360>;
+	txc-skew-ps = <1860>;
+	rxc-skew-ps = <1860>;
+};
+
+&sata {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi5_mba6x: ecspi5grp-mba6x {
+		fsl,pins = <
+			/* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
+			MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO 0x1b099
+			MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI 0xb099
+			MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK 0xb099
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0xb099 /* eCSPI5 SS0 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dts b/arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dts
new file mode 100644
index 000000000000..349a08605a5e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6q-tqma6a.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6a.dtsi"
+#include "imx6q-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6Q on MBa6x";
+	compatible = "tq,imx6q-mba6x-a", "tq,mba6a",
+		     "tq,imx6q-tqma6q-a", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-mba6b.dts b/arch/arm/boot/dts/nxp/imx/imx6q-mba6b.dts
new file mode 100644
index 000000000000..02c9f3e91b8f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mba6b.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6q-tqma6b.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6b.dtsi"
+#include "imx6q-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6Q on MBa6x";
+	compatible = "tq,imx6q-mba6x-b", "tq,mba6b",
+		     "tq,imx6q-tqma6q-b", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-mccmon6.dts
index a4d295455e67..f08b37010291 100644
--- a/arch/arm/boot/dts/imx6q-mccmon6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mccmon6.dts
@@ -100,8 +100,10 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
@@ -237,7 +239,6 @@
 };
 
 &pwm2 {
-	#pwm-cells = <3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6_max.dts b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dts
index 03bec0c53063..03bec0c53063 100644
--- a/arch/arm/boot/dts/imx6q-nitrogen6_max.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dts
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6_som2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_som2.dts
index eb4eecb6ed22..eb4eecb6ed22 100644
--- a/arch/arm/boot/dts/imx6q-nitrogen6_som2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_som2.dts
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6x.dts
index 435445a34ad0..435445a34ad0 100644
--- a/arch/arm/boot/dts/imx6q-nitrogen6x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6x.dts
diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
index 61347a545d6c..a7d5a68110fc 100644
--- a/arch/arm/boot/dts/imx6q-novena.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
@@ -86,7 +86,7 @@
 			linux,code = <KEY_POWER>;
 		};
 
-		lid {
+		lid-event {
 			label = "Lid";
 			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;	/* EV_SW */
@@ -99,7 +99,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds_novena>;
 
-		heartbeat {
+		led-heartbeat {
 			label = "novena:white:panel";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
@@ -107,7 +107,7 @@
 	};
 
 	panel: panel {
-		compatible = "innolux,n133hse-ea1", "simple-panel";
+		compatible = "innolux,n133hse-ea1";
 		backlight = <&backlight>;
 	};
 
@@ -222,20 +222,30 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet_novena>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-	rxc-skew-ps = <3000>;
-	rxdv-skew-ps = <0>;
-	txc-skew-ps = <3000>;
-	txen-skew-ps = <0>;
-	rxd0-skew-ps = <0>;
-	rxd1-skew-ps = <0>;
-	rxd2-skew-ps = <0>;
-	rxd3-skew-ps = <0>;
-	txd0-skew-ps = <3000>;
-	txd1-skew-ps = <3000>;
-	txd2-skew-ps = <3000>;
-	txd3-skew-ps = <3000>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			rxc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			txen-skew-ps = <0>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <3000>;
+			txd1-skew-ps = <3000>;
+			txd2-skew-ps = <3000>;
+			txd3-skew-ps = <3000>;
+		};
+	};
 };
 
 &hdmi {
@@ -298,7 +308,7 @@
 	pinctrl-0 = <&pinctrl_i2c2_novena>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -455,6 +465,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-emmc.dts
index 2e70ea5623c6..322f071d972f 100644
--- a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-emmc.dts
@@ -8,6 +8,9 @@
 #include "imx6q.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with eMMC";
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-nand.dts
index 65d2e483c136..3f13726c8058 100644
--- a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
 #include "imx6q.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with NAND";
diff --git a/arch/arm/boot/dts/imx6q-phytec-pbab01.dts b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pbab01.dts
index affe30b02d5a..affe30b02d5a 100644
--- a/arch/arm/boot/dts/imx6q-phytec-pbab01.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pbab01.dts
diff --git a/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pfla02.dtsi
index 500944bd2a05..500944bd2a05 100644
--- a/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pfla02.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-dwarf.dts
new file mode 100644
index 000000000000..479a63ed42af
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-dwarf.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-pico-pi.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 Quad Board and Dwarf baseboard";
+	compatible = "technexion,imx6q-pico-dwarf", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-hobbit.dts
new file mode 100644
index 000000000000..b767131068f5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-hobbit.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-pico-hobbit.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 Quad Board and Hobbit baseboard";
+	compatible = "technexion,imx6q-pico-hobbit", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-pico-nymph.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-nymph.dts
new file mode 100644
index 000000000000..e8ad4c12b263
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-nymph.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-pico-pi.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 Quad Board and Nymph baseboard";
+	compatible = "technexion,imx6q-pico-nymph", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-pi.dts
new file mode 100644
index 000000000000..cc2394ddad6c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-pi.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-pico-pi.dtsi"
+
+/ {
+	model = "TechNexion PICO-IMX6 Quad Board and PI baseboard";
+	compatible = "technexion,imx6q-pico-pi", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6q-pinfunc.h
index e40409d04b97..e40409d04b97 100644
--- a/arch/arm/boot/dts/imx6q-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6q-pistachio.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
index a31b17eaf51c..46c6b96d8073 100644
--- a/arch/arm/boot/dts/imx6q-pistachio.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
@@ -100,7 +100,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 			wakeup-source;
@@ -196,6 +196,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c1_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_1p8v>;
@@ -208,7 +209,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -570,6 +571,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -635,11 +637,11 @@
 };
 
 &usbphy1 {
-	fsl,tx-d-cal = <0x5>;
+	fsl,tx-d-cal = <79>;
 };
 
 &usbphy2 {
-	fsl,tx-d-cal = <0x5>;
+	fsl,tx-d-cal = <79>;
 };
 
 &usdhc1 {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts b/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
new file mode 100644
index 000000000000..3508a2cd928a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	model = "Protonic PRTI6Q board";
+	compatible = "prt,prti6q", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <1>;
+		power-supply = <&reg_3v3>;
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	can_osc: can-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-debug0 {
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-debug1 {
+			function = LED_FUNCTION_SD;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg121xglp";
+		backlight = <&backlight_lcd>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		enable-active-high;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "regulator-WL12xx";
+		startup-delay-us = <70000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+
+	sound-spdif {
+		compatible = "fsl,imx-audio-spdif";
+		model = "imx-spdif";
+		spdif-controller = <&spdif>;
+		spdif-in;
+		spdif-out;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0		       IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>, <&gpio4 25 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+	status = "okay";
+
+	can@0 {
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can3>;
+		clocks = <&can_osc>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <5000000>;
+	};
+
+	adc@1 {
+		compatible = "ti,adc128s052";
+		reg = <1>;
+		spi-max-frequency = <2000000>;
+		vref-supply = <&reg_3v3>;
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ9031RNX PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+};
+
+/* DDC */
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* can2_l */
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		/* can2_h */
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		/* can1_l */
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		/* can1_h */
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&sata {
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdif>;
+	status = "okay";
+};
+
+&ssi1 {
+	#sound-dai-cells = <0>;
+	fsl,mode = "ac97-slave";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	non-removable;
+	vmmc-supply = <&reg_wifi>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wifi@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi>;
+		interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+		ref-clock-frequency = <38400000>;
+		tcxo-clock-frequency = <19200000>;
+	};
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX	0x1b008
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX	0x1b008
+		>;
+	};
+
+	pinctrl_can3: can3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x1b0b1
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO		0x100b1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK		0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI		0x100b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x000b1
+		>;
+	};
+
+	pinctrl_ecspi2_cs: ecspi2csgrp {
+		fsl,pins = <
+			/* ADC128S022 CS */
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x1b0b1
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x10030
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x10030
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x10030
+
+			/* Phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b1
+		>;
+	};
+
+	pinctrl_hdmi: hdmigrp {
+		fsl,pins = <
+			/* NOTE: DDC is done via I2C2, so DON'T
+			 * configure DDC pins for HDMI!
+			 */
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1f8b0
+		>;
+	};
+
+	/* DDC */
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b0
+		>;
+	};
+
+	pinctrl_spdif: spdifgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_16__SPDIF_IN		0x1b0b0
+			MX6QDL_PAD_GPIO_19__SPDIF_OUT		0x1b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B	0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg_id: usbotgidgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1f058
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_wifi: wifigrp {
+		fsl,pins = <
+			/* WL12xx IRQ */
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x10880
+		>;
+	};
+
+	pinctrl_wifi_npd: wifinpd {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b8b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-prtwd2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-prtwd2.dts
new file mode 100644
index 000000000000..792b8903d345
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-prtwd2.dts
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2018 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Protonic WD2 board";
+	compatible = "prt,prtwd2", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+	};
+
+	/* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
+	i2c {
+		compatible = "i2c-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c4>;
+		sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+		i2c-gpio,delay-us = <20>;	/* ~10 kHz */
+		i2c-gpio,scl-output-only;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		pause;
+		full-duplex;
+	};
+};
+
+&i2c3 {
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* V in */
+		channel@4 {
+			reg = <4>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+
+		/* I charge */
+		channel@5 {
+			reg = <5>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+
+		/* V bus  */
+		channel@6 {
+			reg = <6>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+
+		/* nc */
+		channel@7 {
+			reg = <7>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	no-1-8-v;
+	non-removable;
+	mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_eth_chg>;
+
+	pinctrl_can1phy: can1phy {
+		fsl,pins = <
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12	0x13070
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x130b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22	0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__GPIO1_IO22	0x1f8b0
+			MX6QDL_PAD_ENET_MDC__GPIO1_IO31		0x1f8b0
+		>;
+	};
+
+	pinctrl_usb_eth_chg: usbethchggrp {
+		fsl,pins = <
+			/* USB charging control */
+			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x130b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x130b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x130b0
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x130b0
+			>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_wifi_npd: wifinpd {
+		fsl,pins = <
+			/* WL_REG_ON */
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x13069
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-rex-pro.dts b/arch/arm/boot/dts/nxp/imx/imx6q-rex-pro.dts
index 1767e1a3cd53..271f4b2d9b9f 100644
--- a/arch/arm/boot/dts/imx6q-rex-pro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-rex-pro.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf032b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dts
index 6e981a3e0a83..6e981a3e0a83 100644
--- a/arch/arm/boot/dts/imx6q-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dts
new file mode 100644
index 000000000000..7c6a2f234ccb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-sabrelite.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad SABRE Lite Board";
+	compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
+
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabresd.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sabresd.dts
index eec944673c0b..eec944673c0b 100644
--- a/arch/arm/boot/dts/imx6q-sabresd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sabresd.dts
diff --git a/arch/arm/boot/dts/imx6q-savageboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-savageboard.dts
index 717ac62fc2cf..717ac62fc2cf 100644
--- a/arch/arm/boot/dts/imx6q-savageboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-savageboard.dts
diff --git a/arch/arm/boot/dts/imx6q-sbc6x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sbc6x.dts
index 9054c1d58b9d..9054c1d58b9d 100644
--- a/arch/arm/boot/dts/imx6q-sbc6x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sbc6x.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt2.dts
new file mode 100644
index 000000000000..ff97d22eb09f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt2.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+#include "imx6qdl-skov-revc-lt2.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU QuadCore";
+	compatible = "skov,imx6q-skov-revc-lt2", "fsl,imx6q";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001f878
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001f878
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt6.dts
new file mode 100644
index 000000000000..3e3b36ad362a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt6.dts
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+#include "imx6qdl-skov-cpu-revc.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU QuadCore";
+	compatible = "skov,imx6q-skov-revc-lt6", "fsl,imx6q";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	display {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "logictechno,lttd800480070-l6wh-rt";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001F878
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001F878
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-skov-reve-mi1010ait-1cp1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-skov-reve-mi1010ait-1cp1.dts
new file mode 100644
index 000000000000..0342a79ccd5d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-skov-reve-mi1010ait-1cp1.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-skov-cpu.dtsi"
+
+/ {
+	model = "SKOV IMX6 CPU QuadCore";
+	compatible = "skov,imx6q-skov-reve-mi1010ait-1cp1", "fsl,imx6q";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	panel {
+		compatible = "multi-inno,mi1010ait-1cp";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>, <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+				 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>, <&clk50m_phy>;
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+		wakeup-source;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			/* external 1 k pull up */
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x40010878
+			/* external 1 k pull up */
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x40010878
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001F878
+			/* internal 22 k pull up required */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001F878
+		>;
+	};
+
+	pinctrl_touchscreen: touchscreengrp {
+		fsl,pins = <
+			/* external 10 k pull up */
+			/* CTP_INT */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
+			/* CTP_RST */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0
+		>;
+	};
+};
+
+&reg_tft_vcom {
+	regulator-min-microvolt = <3160000>;
+	regulator-max-microvolt = <3160000>;
+	voltage-table = <3160000 73>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/nxp/imx/imx6q-solidsense.dts
index dc51262e7b2f..0e6a325df363 100644
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-solidsense.dts
@@ -1,6 +1,6 @@
 /*
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
+ * Copyright (C) 2015 Rabeeh Khoury <rabeeh@solid-run.com>
+ * Based on dt work by Russell King
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -39,21 +39,16 @@
  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
-
 /dts-v1/;
+
 #include "imx6q.dtsi"
-#include "imx6qdl-sabrelite.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-emmc.dtsi"
+#include "imx6qdl-sr-som-ti.dtsi"
+#include "imx6qdl-hummingboard2.dtsi"
+#include "imx6qdl-solidsense.dtsi"
 
 / {
-	model = "Freescale i.MX6 Quad SABRE Lite Board";
-	compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
-};
-
-&sata {
-	status = "okay";
-};
-
-&ipu1_csi1_from_mipi_vc1 {
-	clock-lanes = <0>;
-	data-lanes = <1 2>;
+	model = "SolidRun SolidSense Dual/Quad (1.5som+emmc)";
+	compatible = "solidrun,solidsense/q", "fsl,imx6q";
 };
diff --git a/arch/arm/boot/dts/imx6q-tbs2910.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tbs2910.dts
index bfff87ce2e1f..7c298d9aa21e 100644
--- a/arch/arm/boot/dts/imx6q-tbs2910.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tbs2910.dts
@@ -16,6 +16,13 @@
 		stdout-path = &uart1;
 	};
 
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc4;
+		/delete-property/ mmc3;
+	};
+
 	memory@10000000 {
 		device_type = "memory";
 		reg = <0x10000000 0x80000000>;
@@ -42,7 +49,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		blue {
+		led-blue {
 			label = "blue_status_led";
 			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -99,8 +106,20 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-handle = <&phy>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+		};
+	};
 };
 
 &hdmi {
@@ -122,6 +141,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};
@@ -140,7 +160,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	rtc: ds1307@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1307";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tqma6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6a.dtsi
new file mode 100644
index 000000000000..ab4c07c13a13
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6a.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6q.dtsi"
+#include "imx6qdl-tqma6a.dtsi"
+#include "imx6qdl-tqma6.dtsi"
+
+/ {
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6b.dtsi
new file mode 100644
index 000000000000..7224c376c318
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6b.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ */
+
+#include "imx6q.dtsi"
+#include "imx6qdl-tqma6b.dtsi"
+#include "imx6qdl-tqma6.dtsi"
+
+/ {
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-ts4900.dts b/arch/arm/boot/dts/nxp/imx/imx6q-ts4900.dts
index dce1e8671ebe..dce1e8671ebe 100644
--- a/arch/arm/boot/dts/imx6q-ts4900.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ts4900.dts
diff --git a/arch/arm/boot/dts/imx6q-ts7970.dts b/arch/arm/boot/dts/nxp/imx/imx6q-ts7970.dts
index 570bd3c309a6..570bd3c309a6 100644
--- a/arch/arm/boot/dts/imx6q-ts7970.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ts7970.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010-comtft.dts
index ac3050a835e5..ac3050a835e5 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010-comtft.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010.dts
index 4ee860b626ff..4ee860b626ff 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1010.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020-comtft.dts
index a773f252816c..a773f252816c 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020-comtft.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020.dts
index 0a4daec8d3ad..0a4daec8d3ad 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1020.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036-mb7.dts
index 9ffbb0fe7df8..9ffbb0fe7df8 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1036-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036-mb7.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036.dts
index cb2fcb4896c6..cb2fcb4896c6 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1036.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-10x0-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-10x0-mb7.dts
index d43a5d8f1749..d43a5d8f1749 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-10x0-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-10x0-mb7.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1110.dts
index f7b0acb65352..f7b0acb65352 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1110.dts
diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-11x0-mb7.dts
index 387edf2b3f96..387edf2b3f96 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-11x0-mb7.dts
diff --git a/arch/arm/boot/dts/imx6q-udoo.dts b/arch/arm/boot/dts/nxp/imx/imx6q-udoo.dts
index 52e9f4a211d0..52e9f4a211d0 100644
--- a/arch/arm/boot/dts/imx6q-udoo.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-udoo.dts
diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/nxp/imx/imx6q-utilite-pro.dts
index d16ff2083d62..ad59b23ef27a 100644
--- a/arch/arm/boot/dts/imx6q-utilite-pro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-utilite-pro.dts
@@ -89,7 +89,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
index c54362fcc508..2290c1237634 100644
--- a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
@@ -28,7 +28,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		back {
+		key-back {
 			gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			label = "Key Back";
@@ -37,7 +37,7 @@
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			label = "Key Home";
@@ -46,7 +46,7 @@
 			wakeup-source;
 		};
 
-		menu {
+		key-menu {
 			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
 			label = "Key Menu";
@@ -144,8 +144,8 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
-		   <&gpio4 10 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>,
+		   <&gpio4 10 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -203,6 +203,7 @@
 };
 
 &pwm2 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-var-mx6customboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-var-mx6customboard.dts
new file mode 100644
index 000000000000..18a620832a2a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-var-mx6customboard.dts
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite MX6 Carrier-board
+ *
+ * Copyright 2016 Variscite, Ltd. All Rights Reserved
+ * Copyright 2022 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6qdl-var-som.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6 Custom Board";
+	compatible = "variscite,mx6customboard", "variscite,var-som-imx6q", "fsl,imx6q";
+
+	panel0: lvds-panel0 {
+		compatible = "panel-lvds";
+		backlight = <&backlight_lvds>;
+		width-mm = <152>;
+		height-mm = <91>;
+		label = "etm070001adh6";
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <32000000>;
+			hactive = <800>;
+			vactive = <480>;
+			hback-porch = <39>;
+			hfront-porch = <39>;
+			vback-porch = <29>;
+			vfront-porch = <13>;
+			hsync-len = <47>;
+			vsync-len = <2>;
+		};
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	panel1: lvds-panel1 {
+		compatible = "panel-lvds";
+		width-mm = <152>;
+		height-mm = <91>;
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <38251000>;
+			hactive = <800>;
+			vactive = <600>;
+			hback-porch = <112>;
+			hfront-porch = <32>;
+			vback-porch = <3>;
+			vfront-porch = <17>;
+			hsync-len = <80>;
+			vsync-len = <4>;
+		};
+
+		port {
+			panel_in_lvds1: endpoint {
+				remote-endpoint = <&lvds1_out>;
+			};
+		};
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 50000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 248>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_3p3v>;
+		touchscreen-size-x = <880>;
+		touchscreen-size-y = <1280>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <1800>;
+		touchscreen-size-y = <1000>;
+	};
+};
+
+&iomuxc {
+	pinctrl_camera: cameragrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN	0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC		0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__FLEXCAN1_TX		0x1b0b0
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_EB3__UART3_RTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg_var: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17071
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x10071
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x17071
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x17071
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x17071
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x17071
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+				remote-endpoint = <&panel_in_lvds1>;
+			};
+		};
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-vicut1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-vicut1.dts
new file mode 100644
index 000000000000..dd91aff3f9e2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-vicut1.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
+
+/ {
+	model = "Kverneland UT1Q Board";
+	compatible = "kvg,vicut1q", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-wandboard-revb1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revb1.dts
index f6ccbecff92c..f6ccbecff92c 100644
--- a/arch/arm/boot/dts/imx6q-wandboard-revb1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revb1.dts
diff --git a/arch/arm/boot/dts/imx6q-wandboard-revd1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revd1.dts
index 55331021d80c..55331021d80c 100644
--- a/arch/arm/boot/dts/imx6q-wandboard-revd1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revd1.dts
diff --git a/arch/arm/boot/dts/imx6q-wandboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard.dts
index 0be548beef86..0be548beef86 100644
--- a/arch/arm/boot/dts/imx6q-wandboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-crux.dts b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-crux.dts
new file mode 100644
index 000000000000..bddf3822ebf7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-crux.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Crux i.MX6Quad board";
+	compatible = "ysoft,imx6q-yapp4-crux", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&uart2 {
+	status = "disabled";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-pegasus.dts b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-pegasus.dts
new file mode 100644
index 000000000000..ec6651ba4ba2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-pegasus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Pegasus i.MX6Quad board";
+	compatible = "ysoft,imx6q-yapp4-pegasus", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-zii-rdu2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-zii-rdu2.dts
index a1c5e69d81ba..a1c5e69d81ba 100644
--- a/arch/arm/boot/dts/imx6q-zii-rdu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-zii-rdu2.dts
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q.dtsi
index 9d3be1cc6b64..df86049a695b 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q.dtsi
@@ -49,6 +49,8 @@
 			arm-supply = <&reg_arm>;
 			pu-supply = <&reg_pu>;
 			soc-supply = <&reg_soc>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		cpu1: cpu@1 {
@@ -157,14 +159,17 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-		aips-bus@2000000 { /* AIPS1 */
+		aips1: bus@2000000 { /* AIPS1 */
 			spba-bus@2000000 {
 				ecspi5: spi@2018000 {
 					#address-cells = <1>;
@@ -175,15 +180,11 @@
 					clocks = <&clks IMX6Q_CLK_ECSPI5>,
 						 <&clks IMX6Q_CLK_ECSPI5>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 11 8 1>, <&sdma 12 8 2>;
+					dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 			};
-
-			iomuxc: iomuxc@20e0000 {
-				compatible = "fsl,imx6q-iomuxc";
-			};
 		};
 
 		sata: sata@2200000 {
@@ -408,23 +409,29 @@
 &hdmi {
 	compatible = "fsl,imx6q-hdmi";
 
-	port@2 {
-		reg = <2>;
+	ports {
+		port@2 {
+			reg = <2>;
 
-		hdmi_mux_2: endpoint {
-			remote-endpoint = <&ipu2_di0_hdmi>;
+			hdmi_mux_2: endpoint {
+				remote-endpoint = <&ipu2_di0_hdmi>;
+			};
 		};
-	};
 
-	port@3 {
-		reg = <3>;
+		port@3 {
+			reg = <3>;
 
-		hdmi_mux_3: endpoint {
-			remote-endpoint = <&ipu2_di1_hdmi>;
+			hdmi_mux_3: endpoint {
+				remote-endpoint = <&ipu2_di1_hdmi>;
+			};
 		};
 	};
 };
 
+&iomuxc {
+	compatible = "fsl,imx6q-iomuxc";
+};
+
 &ipu1_csi1 {
 	ipu1_csi1_from_mipi_vc1: endpoint {
 		remote-endpoint = <&mipi_vc1_to_ipu1_csi1>;
diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis.dtsi
index ff1287e6b7ce..2ae93f57fe5a 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis.dtsi
@@ -1,52 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2017 Toradex AG
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Toradex Apalis iMX6Q/D Module";
 	compatible = "toradex,apalis_imx6q", "fsl,imx6q";
 
+	aliases {
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC1 slot */
+		mmc2 = &usdhc2; /* SD1 slot */
+		/delete-property/ mmc3;
+	};
+
 	/* Will be filled by the bootloader */
 	memory@10000000 {
 		device_type = "memory";
@@ -55,88 +27,182 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm4 0 5000000>;
-		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm4 0 5000000 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	clk_ov5640_osc: clk-ov5640-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
 		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di1_disp1>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel_lvds: panel-lvds {
+		compatible = "panel-lvds";
+		backlight = <&backlight>;
+		status = "disabled";
+
+		port {
+			lvds_panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
 	};
 
 	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3";
 	};
 
 	reg_module_3v3_audio: regulator-module-3v3-audio {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3_AUDIO";
-		regulator-min-microvolt = <3300000>;
+		regulator-always-on;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_AUDIO";
+	};
+
+	reg_ov5640_1v8_d_o_vdd: regulator-ov5640-1v8-d-o-vdd {
+		compatible = "regulator-fixed";
 		regulator-always-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "DOVDD/DVDD_1.8V";
+		/* Note: The CSI module uses on-board 3.3V_SW supply */
+		vin-supply = <&reg_module_3v3>;
+	};
+
+	reg_ov5640_2v8_a_vdd: regulator-ov5640-2v8-a-vdd {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <2800000>;
+		regulator-min-microvolt = <2800000>;
+		regulator-name = "AVDD/AFVDD_2.8V";
+		/* Note: The CSI module uses on-board 3.3V_SW supply */
+		vin-supply = <&reg_module_3v3>;
 	};
 
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbotg_pwr>;
-		regulator-name = "usb_otg_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg_vbus";
 		status = "disabled";
 	};
 
 	/* on module USB hub */
 	reg_usb_host_vbus_hub: regulator-usb-host-vbus-hub {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbhub_pwr>;
-		regulator-name = "usb_host_vbus_hub";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus_hub";
 		startup-delay-us = <2000>;
-		enable-active-high;
 		status = "okay";
 	};
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
-		regulator-name = "usb_host_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio =  <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus";
 		vin-supply = <&reg_usb_host_vbus_hub>;
 		status = "disabled";
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx6q-apalis-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"LINE_IN", "Line In Jack",
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias",
 			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
+		model = "imx6q-apalis-sgtl5000";
 		mux-ext-port = <4>;
+		mux-int-port = <1>;
+		ssi-controller = <&ssi1>;
 	};
 
 	sound_spdif: sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
-		model = "imx-spdif";
 		spdif-controller = <&spdif>;
 		spdif-in;
 		spdif-out;
+		model = "imx-spdif";
 		status = "disabled";
 	};
 };
@@ -161,9 +227,13 @@
 	status = "disabled";
 };
 
+&clks {
+	fsl,pmic-stby-poweroff;
+};
+
 /* Apalis SPI1 */
 &ecspi1 {
-	cs-gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "disabled";
@@ -171,16 +241,224 @@
 
 /* Apalis SPI2 */
 &ecspi2 {
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "disabled";
 };
 
+&gpio1 {
+	gpio-line-names = "MXM3_84",
+			  "MXM3_4",
+			  "MXM3_15/GPIO7",
+			  "MXM3_96",
+			  "MXM3_37",
+			  "",
+			  "MXM3_17/GPIO8",
+			  "MXM3_14",
+			  "MXM3_12",
+			  "MXM3_2",
+			  "MXM3_184",
+			  "MXM3_180",
+			  "MXM3_178",
+			  "MXM3_176",
+			  "MXM3_188",
+			  "MXM3_186",
+			  "MXM3_160",
+			  "MXM3_162",
+			  "MXM3_150",
+			  "MXM3_144",
+			  "MXM3_154",
+			  "MXM3_146",
+			  "",
+			  "",
+			  "MXM3_72";
+};
+
+&gpio2 {
+	gpio-line-names = "MXM3_148",
+			  "MXM3_152",
+			  "MXM3_156",
+			  "MXM3_158",
+			  "MXM3_1/GPIO1",
+			  "MXM3_3/GPIO2",
+			  "MXM3_5/GPIO3",
+			  "MXM3_7/GPIO4",
+			  "MXM3_95",
+			  "MXM3_6",
+			  "MXM3_8",
+			  "MXM3_123",
+			  "MXM3_126",
+			  "MXM3_128",
+			  "MXM3_130",
+			  "MXM3_132",
+			  "MXM3_253",
+			  "MXM3_251",
+			  "MXM3_283",
+			  "MXM3_281",
+			  "MXM3_279",
+			  "MXM3_277",
+			  "MXM3_243",
+			  "MXM3_235",
+			  "MXM3_231",
+			  "MXM3_229",
+			  "MXM3_233",
+			  "MXM3_198",
+			  "MXM3_275",
+			  "MXM3_273",
+			  "MXM3_207",
+			  "MXM3_122";
+};
+
+&gpio3 {
+	gpio-line-names = "MXM3_271",
+			  "MXM3_269",
+			  "MXM3_301",
+			  "MXM3_299",
+			  "MXM3_297",
+			  "MXM3_295",
+			  "MXM3_293",
+			  "MXM3_291",
+			  "MXM3_289",
+			  "MXM3_287",
+			  "MXM3_249",
+			  "MXM3_247",
+			  "MXM3_245",
+			  "MXM3_286",
+			  "MXM3_239",
+			  "MXM3_35",
+			  "MXM3_205",
+			  "MXM3_203",
+			  "MXM3_201",
+			  "MXM3_116",
+			  "MXM3_114",
+			  "MXM3_262",
+			  "MXM3_274",
+			  "MXM3_124",
+			  "MXM3_110",
+			  "MXM3_120",
+			  "MXM3_263",
+			  "MXM3_265",
+			  "",
+			  "MXM3_135",
+			  "MXM3_261",
+			  "MXM3_259";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_194",
+			  "MXM3_136",
+			  "MXM3_134",
+			  "MXM3_140",
+			  "MXM3_138",
+			  "",
+			  "MXM3_220",
+			  "",
+			  "",
+			  "MXM3_18",
+			  "MXM3_16",
+			  "",
+			  "",
+			  "MXM3_214",
+			  "MXM3_216",
+			  "MXM3_164";
+};
+
+&gpio5 {
+	gpio-line-names = "MXM3_159",
+			  "",
+			  "",
+			  "",
+			  "MXM3_257",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_200",
+			  "MXM3_196",
+			  "MXM3_204",
+			  "MXM3_202",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_191",
+			  "MXM3_197",
+			  "MXM3_77",
+			  "MXM3_195",
+			  "MXM3_221",
+			  "MXM3_225",
+			  "MXM3_223",
+			  "MXM3_227",
+			  "MXM3_209",
+			  "MXM3_211",
+			  "MXM3_118",
+			  "MXM3_112",
+			  "MXM3_187",
+			  "MXM3_185";
+};
+
+&gpio6 {
+	gpio-line-names = "MXM3_183",
+			  "MXM3_181",
+			  "MXM3_179",
+			  "MXM3_177",
+			  "MXM3_175",
+			  "MXM3_173",
+			  "MXM3_255",
+			  "MXM3_83",
+			  "MXM3_91",
+			  "MXM3_13/GPIO6",
+			  "MXM3_11/GPIO5",
+			  "MXM3_79",
+			  "",
+			  "",
+			  "MXM3_190",
+			  "MXM3_193",
+			  "MXM3_89";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_99",
+			  "MXM3_85",
+			  "MXM3_217",
+			  "MXM3_215";
+};
+
+&gpr {
+	ipu1_csi0_mux {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		port@1 {
+			reg = <1>;
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+				remote-endpoint = <&adv7280_to_ipu1_csi0_mux>;
+			};
+		};
+	};
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy>;
 	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
@@ -200,7 +478,7 @@
 
 &hdmi {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hdmi_ddc>;
+	pinctrl-0 = <&pinctrl_hdmi_ddc &pinctrl_hdmi_cec>;
 	status = "disabled";
 };
 
@@ -213,6 +491,16 @@
 	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		/* These GPIOs are muxed with the iomuxc node */
+		interrupt-parent = <&gpio6>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;	/* MXM3_11 */
+		reg = <0x4a>;
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;	/* MXM3_13 */
+		status = "disabled";
+	};
 };
 
 /*
@@ -228,101 +516,105 @@
 	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
+		fsl,pmic-stby-poweroff;
 		reg = <0x08>;
 
 		regulators {
 			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <400000>;
 			};
 
 			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <5150000>;
+				regulator-min-microvolt = <5000000>;
 			};
 
 			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1000000>;
 			};
 
 			vref_reg: vrefddr {
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
 			};
 
 			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 		};
 	};
 
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&vgen4_reg>;
@@ -331,25 +623,25 @@
 	/* STMPE811 touch screen controller */
 	stmpe811@41 {
 		compatible = "st,stmpe811";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch_int>;
-		reg = <0x41>;
+		blocks = <0x5>;
+		id = <0>;
 		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-parent = <&gpio4>;
 		interrupt-controller;
-		id = <0>;
-		blocks = <0x5>;
+		interrupt-parent = <&gpio4>;
 		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		reg = <0x41>;
 		/* 3.25 MHz ADC clock speed */
 		st,adc-freq = <1>;
 		/* 12-bit ADC */
 		st,mod-12b = <1>;
 		/* internal ADC reference */
 		st,ref-sel = <0>;
-		/* ADC converstion time: 80 clocks */
+		/* ADC conversion time: 80 clocks */
 		st,sample-time = <4>;
 
-		stmpe_touchscreen {
+		stmpe_ts: stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
 			/* 8 sample average control */
 			st,ave-ctrl = <3>;
@@ -364,10 +656,12 @@
 			st,settling = <3>;
 			/* 5 ms touch detect interrupt delay */
 			st,touch-det-delay = <5>;
+			status = "disabled";
 		};
 
-		stmpe_adc {
+		stmpe_adc: stmpe_adc {
 			compatible = "st,stmpe-adc";
+			#io-channel-cells = <1>;
 			/* forbid to use ADC channels 3-0 (touch) */
 			st,norequest-mask = <0x0F>;
 		};
@@ -386,6 +680,90 @@
 	scl-gpios = <&gpio3 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	adv_7280: adv7280@21 {
+		compatible = "adi,adv7280";
+		adv,force-bt656-4;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_csi0>;
+		reg = <0x21>;
+		status = "disabled";
+
+		port {
+			adv7280_to_ipu1_csi0_mux: endpoint {
+				bus-width = <8>;
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+
+	ov5640_csi_cam: ov5640_mipi@3c {
+		compatible = "ovti,ov5640";
+		AVDD-supply = <&reg_ov5640_2v8_a_vdd>;
+		DOVDD-supply = <&reg_ov5640_1v8_d_o_vdd>;
+		DVDD-supply = <&reg_ov5640_1v8_d_o_vdd>;
+		clock-names = "xclk";
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cam_mclk>;
+		/* These GPIOs are muxed with the iomuxc node */
+		powerdown-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		reg = <0x3c>;
+		reset-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&mipi_csi_from_ov5640>;
+			};
+		};
+	};
+};
+
+&ipu1_di1_disp1 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	lvds-channel@0 {
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+			};
+		};
+	};
+};
+
+&mipi_csi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "disabled";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi_from_ov5640: endpoint {
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+		};
+	};
 };
 
 &pwm1 {
@@ -423,72 +801,72 @@
 };
 
 &uart1 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 &uart2 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2_dte>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 &uart4 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
 &uart5 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart5_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
 &usbotg {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
 	status = "disabled";
 };
 
 /* MMC1 */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
+	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "disabled";
 };
 
 /* SD1 */
 &usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	disable-wp;
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "disabled";
 };
 
 /* eMMC */
 &usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "okay";
 };
 
@@ -497,49 +875,57 @@
 };
 
 &iomuxc {
-	pinctrl_apalis_gpio1: gpio2io04grp {
+	/* Mux the Apalis GPIOs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
+		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
+		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
+		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
+		    >;
+
+	pinctrl_apalis_gpio1: apalisgpio1grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio2: gpio2io05grp {
+	pinctrl_apalis_gpio2: apalisgpio2grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio3: gpio2io06grp {
+	pinctrl_apalis_gpio3: apalisgpio3grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio4: gpio2io07grp {
+	pinctrl_apalis_gpio4: apalisgpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio5: gpio6io10grp {
+	pinctrl_apalis_gpio5: apalisgpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio6: gpio6io09grp {
+	pinctrl_apalis_gpio6: apalisgpio6grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio7: gpio1io02grp {
+	pinctrl_apalis_gpio7: apalisgpio7grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio8: gpio1io06grp {
+	pinctrl_apalis_gpio8: apalisgpio8grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x130b0
 		>;
@@ -551,8 +937,6 @@
 			MX6QDL_PAD_DISP0_DAT21__AUD4_TXD	0x130b0
 			MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS	0x130b0
 			MX6QDL_PAD_DISP0_DAT23__AUD4_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
 		>;
 	};
 
@@ -634,7 +1018,7 @@
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpioblon {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b0
 		>;
@@ -779,7 +1163,7 @@
 		>;
 	};
 
-	pinctrl_mmc_cd: gpiommccdgrp {
+	pinctrl_mmc_cd: mmccdgrp {
 		fsl,pins = <
 			 /* MMC1 CD */
 			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x000b0
@@ -810,41 +1194,47 @@
 		>;
 	};
 
-	pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
+	pinctrl_regulator_usbh_pwr: regusbhpwrgrp {
 		fsl,pins = <
 			/* USBH_EN */
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x0f058
 		>;
 	};
 
-	pinctrl_regulator_usbhub_pwr: gpioregusbhubpwrgrp {
+	pinctrl_regulator_usbhub_pwr: regusbhubpwrgrp {
 		fsl,pins = <
 			/* USBH_HUB_EN */
 			MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0f058
 		>;
 	};
 
-	pinctrl_regulator_usbotg_pwr: gpioregusbotgpwrgrp {
+	pinctrl_regulator_usbotg_pwr: regusbotgpwrgrp {
 		fsl,pins = <
 			/* USBO1 power en */
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0f058
 		>;
 	};
 
-	pinctrl_reset_moci: gpioresetmocigrp {
+	pinctrl_reset_moci: resetmocigrp {
 		fsl,pins = <
 			/* RESET_MOCI control */
 			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0f058
 		>;
 	};
 
-	pinctrl_sd_cd: gpiosdcdgrp {
+	pinctrl_sd_cd: sdcdgrp {
 		fsl,pins = <
 			/* SD1 CD */
 			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x000b0
 		>;
 	};
 
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1	0x130b0
+		>;
+	};
+
 	pinctrl_spdif: spdifgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_16__SPDIF_IN  0x1b0b0
@@ -852,13 +1242,22 @@
 		>;
 	};
 
-	pinctrl_touch_int: gpiotouchintgrp {
+	pinctrl_touch_int: touchintgrp {
 		fsl,pins = <
 			/* STMPE811 interrupt */
 			MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
 		>;
 	};
 
+	/* Additional DTR, DSR, DCD */
+	pinctrl_uart1_ctrl: uart1ctrlgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
+			MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
+			MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
+		>;
+	};
+
 	pinctrl_uart1_dce: uart1dcegrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
@@ -876,15 +1275,6 @@
 		>;
 	};
 
-	/* Additional DTR, DSR, DCD */
-	pinctrl_uart1_ctrl: uart1ctrlgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
-			MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
-			MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
-		>;
-	};
-
 	pinctrl_uart2_dce: uart2dcegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
@@ -938,7 +1328,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_4bit: usdhc1grp_4bit {
+	pinctrl_usdhc1_4bit: usdhc1-4bitgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17071
 			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10071
@@ -949,7 +1339,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_8bit: usdhc1grp_8bit {
+	pinctrl_usdhc1_8bit: usdhc1-8bitgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17071
 			MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17071
diff --git a/arch/arm/boot/dts/imx6qdl-apf6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6.dtsi
index b78ed7974ea9..b78ed7974ea9 100644
--- a/arch/arm/boot/dts/imx6qdl-apf6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
index b8e74ab3c993..338d292553ad 100644
--- a/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
@@ -181,6 +181,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -211,6 +212,7 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos.dtsi
index d954661fa055..baa197c90060 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos.dtsi
@@ -91,12 +91,12 @@
 };
 
 &ecspi4 {
-	cs-gpios = <&gpio3 20 0>;
+	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
index 376750882ed3..db1bc511e71f 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
@@ -110,28 +110,28 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH
-		    &gpio4 10 GPIO_ACTIVE_HIGH
-		    &gpio4 11 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW
+		    &gpio4 10 GPIO_ACTIVE_LOW
+		    &gpio4 11 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 };
 
 &ecspi2 {
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH &gpio2 27 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW &gpio2 27 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 };
 
 &ecspi4 {
-	cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 29 GPIO_ACTIVE_LOW &gpio5 2 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
@@ -154,112 +154,112 @@
 		regulators {
 			bcore1 {
 				regulator-name = "bcore1";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bcore2 {
 				regulator-name = "bcore2";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bpro {
 				regulator-name = "bpro";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bperi {
 				regulator-name = "bperi";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bmem {
 				regulator-name = "bmem";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo2 {
 				regulator-name = "ldo2";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			ldo3 {
 				regulator-name = "ldo3";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo4 {
 				regulator-name = "ldo4";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo5 {
 				regulator-name = "ldo5";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo6 {
 				regulator-name = "ldo6";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo7 {
 				regulator-name = "ldo7";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo8 {
 				regulator-name = "ldo8";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo9 {
 				regulator-name = "ldo9";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo10 {
 				regulator-name = "ldo10";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo11 {
 				regulator-name = "ldo11";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bio {
 				regulator-name = "bio";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 			};
@@ -301,12 +301,12 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	eeprom@50{
+	eeprom@50 {
 		compatible = "atmel,24c64";
 		reg = <0x50>;
 	};
 
-	eeprom@57{
+	eeprom@57 {
 		compatible = "atmel,24c64";
 		reg = <0x57>;
 	};
@@ -316,12 +316,22 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio7 18 GPIO_ACTIVE_LOW>;
-	txd0-skew-ps = <0>;
-	txd1-skew-ps = <0>;
-	txd2-skew-ps = <0>;
-	txd3-skew-ps = <0>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
 };
 
 &gpmi {
@@ -336,6 +346,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri.dtsi
index d03dff23863d..55c90f6393ad 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri.dtsi
@@ -1,61 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2014-2016 Toradex AG
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Toradex Colibri iMX6DL/S Module";
 	compatible = "toradex,colibri_imx6dl", "fsl,imx6dl";
 
+	aliases {
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC/SD Slot */
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+	};
+
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm3 0 5000000>;
-		enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm3 0 5000000 PWM_POLARITY_INVERTED>;
 		status = "disabled";
 	};
 
+	extcon_usbc_det: usbc-det {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbc_det>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio2 22 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	/* Will be filled by the bootloader */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
+	panel_dpi: panel-dpi {
+		/*
+		 * edt,et057090dhu: EDT 5.7" LCD TFT
+		 * edt,et070080dh6: EDT 7.0" LCD TFT
+		 */
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
 	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "+V3.3";
@@ -74,36 +119,36 @@
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
+		gpio = <&gpio3 31 GPIO_ACTIVE_LOW>; /* SODIMM 129 / USBH_PEN */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
-		regulator-name = "usb_host_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus";
 		status = "disabled";
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx6dl-colibri-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"Headphone Jack", "HP_OUT",
 			"LINE_IN", "Line In Jack",
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias";
+		model = "imx6dl-colibri-sgtl5000";
 		mux-int-port = <1>;
 		mux-ext-port = <5>;
+		ssi-controller = <&ssi1>;
 	};
 
 	/* Optional S/PDIF in on SODIMM 88 and out on SODIMM 90, 137 or 168 */
 	sound_spdif: sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
-		model = "imx-spdif";
 		spdif-controller = <&spdif>;
 		spdif-in;
 		spdif-out;
+		model = "imx-spdif";
 		status = "disabled";
 	};
 };
@@ -128,19 +173,23 @@
 	status = "disabled";
 };
 
+&clks {
+	fsl,pmic-stby-poweroff;
+};
+
 /* Colibri SSP */
 &ecspi4 {
-	cs-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "disabled";
 };
 
 &fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
 	status = "okay";
 
 	mdio {
@@ -154,6 +203,224 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "",
+			  "SODIMM_67",
+			  "SODIMM_180",
+			  "SODIMM_196",
+			  "SODIMM_174",
+			  "SODIMM_176",
+			  "SODIMM_194",
+			  "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_28",
+			  "SODIMM_93",
+			  "SODIMM_69",
+			  "SODIMM_99",
+			  "SODIMM_130",
+			  "SODIMM_106",
+			  "SODIMM_98",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_190",
+			  "SODIMM_51",
+			  "SODIMM_47",
+			  "SODIMM_53",
+			  "",
+			  "SODIMM_22";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_132",
+			  "SODIMM_134",
+			  "SODIMM_135",
+			  "SODIMM_133",
+			  "SODIMM_102",
+			  "SODIMM_43",
+			  "SODIMM_127",
+			  "SODIMM_37",
+			  "SODIMM_104",
+			  "SODIMM_59",
+			  "SODIMM_30",
+			  "SODIMM_100",
+			  "SODIMM_38",
+			  "SODIMM_34",
+			  "SODIMM_32",
+			  "SODIMM_36",
+			  "SODIMM_59",
+			  "SODIMM_67",
+			  "SODIMM_97",
+			  "SODIMM_79",
+			  "SODIMM_103",
+			  "SODIMM_101",
+			  "SODIMM_45",
+			  "SODIMM_105",
+			  "SODIMM_107",
+			  "SODIMM_91",
+			  "SODIMM_89",
+			  "SODIMM_150",
+			  "SODIMM_126",
+			  "SODIMM_128",
+			  "",
+			  "SODIMM_94";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_111",
+			  "SODIMM_113",
+			  "SODIMM_115",
+			  "SODIMM_117",
+			  "SODIMM_119",
+			  "SODIMM_121",
+			  "SODIMM_123",
+			  "SODIMM_125",
+			  "SODIMM_110",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_118",
+			  "SODIMM_120",
+			  "SODIMM_122",
+			  "SODIMM_124",
+			  "",
+			  "SODIMM_96",
+			  "SODIMM_77",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_88",
+			  "SODIMM_90",
+			  "SODIMM_31",
+			  "SODIMM_23",
+			  "SODIMM_29",
+			  "SODIMM_71",
+			  "SODIMM_73",
+			  "SODIMM_92",
+			  "SODIMM_81",
+			  "SODIMM_131",
+			  "SODIMM_129";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_168",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_184",
+			  "SODIMM_186",
+			  "HDMI_15",
+			  "HDMI_16",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "SODIMM_24",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_95",
+			  "",
+			  "SODIMM_86",
+			  "",
+			  "SODIMM_65",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_136",
+			  "SODIMM_138",
+			  "SODIMM_140",
+			  "SODIMM_142",
+			  "SODIMM_144",
+			  "SODIMM_146",
+			  "SODIMM_172",
+			  "SODIMM_170",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_159",
+			  "SODIMM_161",
+			  "SODIMM_163",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_165",
+			  "SODIMM_167";
+};
+
+&gpio6 {
+	gpio-line-names = "SODIMM_169",
+			  "SODIMM_171",
+			  "SODIMM_173",
+			  "SODIMM_175",
+			  "SODIMM_177",
+			  "SODIMM_179",
+			  "SODIMM_85",
+			  "SODIMM_166",
+			  "SODIMM_160",
+			  "SODIMM_162",
+			  "SODIMM_158",
+			  "SODIMM_164",
+			  "",
+			  "",
+			  "SODIMM_156",
+			  "SODIMM_75",
+			  "SODIMM_154",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_152";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "",
+			  "SODIMM_137";
+};
+
 &hdmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hdmi_ddc>;
@@ -168,114 +435,127 @@
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
-	pinctrl-0 = <&pinctrl_i2c2_gpio>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
 	scl-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
+		fsl,pmic-stby-poweroff;
 		reg = <0x08>;
 
 		regulators {
 			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <400000>;
 			};
 
 			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <5150000>;
+				regulator-min-microvolt = <5000000>;
 			};
 
 			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1000000>;
 			};
 
 			vref_reg: vrefddr {
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
 			};
 
 			/* vgen1: unused */
 
 			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
-			/* vgen3: unused */
+			/*
+			 * +V3.3_1.8_SD1 coming off VGEN3 and supplying
+			 * the i.MX 6 NVCC_SD1.
+			 */
+			vgen3_reg: vgen3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+			};
 
 			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 		};
 	};
 
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
+		lrclk-strength = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&vgen4_reg>;
-		lrclk-strength = <3>;
 	};
 
 	/* STMPE811 touch screen controller */
 	stmpe811@41 {
 		compatible = "st,stmpe811";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch_int>;
-		reg = <0x41>;
+		blocks = <0x5>;
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-parent = <&gpio6>;
 		interrupt-controller;
 		id = <0>;
-		blocks = <0x5>;
 		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		reg = <0x41>;
 		/* 3.25 MHz ADC clock speed */
 		st,adc-freq = <1>;
 		/* 12-bit ADC */
@@ -285,7 +565,7 @@
 		/* ADC converstion time: 80 clocks */
 		st,sample-time = <4>;
 
-		stmpe_touchscreen {
+		stmpe_ts: stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
 			/* 8 sample average control */
 			st,ave-ctrl = <3>;
@@ -300,9 +580,10 @@
 			st,settling = <3>;
 			/* 5 ms touch detect interrupt delay */
 			st,touch-det-delay = <5>;
+			status = "disabled";
 		};
 
-		stmpe_adc {
+		stmpe_adc: stmpe_adc {
 			compatible = "st,stmpe-adc";
 			/* forbid to use ADC channels 3-0 (touch) */
 			st,norequest-mask = <0x0F>;
@@ -321,6 +602,21 @@
 	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;	/* SODIMM 107 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;	/* SODIMM 106 */
+		status = "disabled";
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
 };
 
 /* Colibri PWM<B> */
@@ -364,57 +660,66 @@
 
 /* Colibri UART_A */
 &uart1 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 /* Colibri UART_B */
 &uart2 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2_dte>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 /* Colibri UART_C */
 &uart3 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
+/* Colibri USBH */
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+};
+
+/* Colibri USBC */
 &usbotg {
-	pinctrl-names = "default";
-	disable-over-current;
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	extcon = <0>, <&extcon_usbc_det>;
 	status = "disabled";
 };
 
 /* Colibri MMC */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
 	cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
-	disable-wp;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	no-1-8-v;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_mmc_cd_sleep>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&vgen3_reg>;
 	status = "disabled";
 };
 
 /* eMMC */
 &usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "okay";
 };
 
@@ -432,14 +737,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh_oc_1>;
 
+	/* Atmel MXT touchsceen + Capacitive Touch Adapter */
+	/* NOTE: This pin group conflicts with pin groups
+	 * pinctrl_pwm1/pinctrl_pwm4. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adap: atmeladaptergrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09   0xb0b1  /* SODIMM  28 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0xb0b1  /* SODIMM  30 */
+		>;
+	};
+
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	/* NOTE: This pin group conflicts with pin groups pinctrl_weim_cs1 and
+	 * pinctrl_weim_cs2. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_conn: atmelconnectorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24  0xb0b1  /* SODIMM_107 */
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0xb0b1  /* SODIMM_106 */
+		>;
+	};
+
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__AUD5_TXC	0x130b0
 			MX6QDL_PAD_KEY_ROW0__AUD5_TXD	0x130b0
 			MX6QDL_PAD_KEY_COL1__AUD5_TXFS	0x130b0
 			MX6QDL_PAD_KEY_ROW1__AUD5_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x000b0
 		>;
 	};
 
@@ -450,28 +775,52 @@
 		>;
 	};
 
+	/* CSI pins used as GPIOs */
+	pinctrl_csi_gpio_1: csigpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D18__GPIO3_IO18   0x1b0b0
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19   0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29   0x130b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06   0x1b0b0
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18   0x1b0b0
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21   0x1b0b0
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20   0x1b0b0
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31   0x1b0b0
+			MX6QDL_PAD_EIM_D17__GPIO3_IO17   0x1b0b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11   0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15  0x1b0b0
+		>;
+	};
+
+	pinctrl_csi_gpio_2: csigpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04   0x1b0b0
+		>;
+	};
+
 	pinctrl_ecspi4: ecspi4grp {
 		fsl,pins = <
+			/* SPI CS */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x000b1
 			MX6QDL_PAD_EIM_D22__ECSPI4_MISO	0x100b1
 			MX6QDL_PAD_EIM_D28__ECSPI4_MOSI	0x100b1
 			MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
-			/* SPI CS */
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x000b1
 		>;
 	};
 
 	pinctrl_enet: enetgrp {
 		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
 			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
-			MX6QDL_PAD_GPIO_16__ENET_REF_CLK     ((1<<30) | 0x1b0b0)
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	((1<<30) | 0x1b0b0)
 		>;
 	};
 
@@ -489,13 +838,32 @@
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpioblon {
+	pinctrl_gpio_1: gpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20     0x1b0b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27      0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03     0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04     0x1b0b0
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06     0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08     0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11     0x1b0b0
+		>;
+	};
+	pinctrl_gpio_2: gpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07       0x1b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08       0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x1b0b0
 		>;
 	};
 
-	pinctrl_gpio_keys: gpiokeys {
+	pinctrl_gpio_keys: gpiokeysgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x130b0
 		>;
@@ -510,15 +878,15 @@
 
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
 		>;
 	};
 
-	pinctrl_i2c2_gpio: i2c2grp {
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x4001b8b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 		>;
 	};
 
@@ -550,8 +918,8 @@
 			MX6QDL_PAD_EIM_EB3__IPU1_CSI1_HSYNC	0xb0b1
 			MX6QDL_PAD_EIM_D29__IPU1_CSI1_VSYNC	0xb0b1
 			/* Disable PWM pins on camera interface */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x40
 			MX6QDL_PAD_GPIO_1__GPIO1_IO01		0x40
+			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x40
 		>;
 	};
 
@@ -582,19 +950,34 @@
 		>;
 	};
 
-	pinctrl_mic_gnd: gpiomicgnd {
+	pinctrl_lvds_transceiver: lvdstxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x03030 /* SODIMM  95 */
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07   0x0b030 /* SODIMM  55 */
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x03030 /* SODIMM  63 */
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x03030 /* SODIMM  99 */
+		>;
+	};
+
+	pinctrl_mic_gnd: micgndgrp {
 		fsl,pins = <
 			/* Controls Mic GND, PU or '1' pull Mic GND to GND */
 			MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x1b0b0
 		>;
 	};
 
-	pinctrl_mmc_cd: gpiommccd {
+	pinctrl_mmc_cd: mmccdgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05	0x1b0b1
 		>;
 	};
 
+	pinctrl_mmc_cd_sleep: mmccdslpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05	0x0
+		>;
+	};
+
 	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x1b0b1
@@ -603,15 +986,15 @@
 
 	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
 			MX6QDL_PAD_EIM_A21__GPIO2_IO17	0x00040
+			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
 		>;
 	};
 
 	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b1
 			MX6QDL_PAD_EIM_A22__GPIO2_IO16	0x00040
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b1
 		>;
 	};
 
@@ -623,15 +1006,15 @@
 
 	pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
 		fsl,pins = <
-			/* USBH_EN */
+			/* SODIMM 129 / USBH_PEN */
 			MX6QDL_PAD_EIM_D31__GPIO3_IO31	0x0f058
 		>;
 	};
 
-	pinctrl_usbh_oc_1: usbhoc1grp {
+	pinctrl_sgtl5000: sgtl5000grp {
 		fsl,pins = <
-			/* USBH_OC */
-			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x000b0
 		>;
 	};
 
@@ -677,9 +1060,9 @@
 	pinctrl_uart2_dte: uart2dtegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA	0x1b0b1
-			MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
-			MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
 			MX6QDL_PAD_SD4_DAT5__UART2_CTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
 		>;
 	};
 
@@ -692,22 +1075,29 @@
 
 	pinctrl_usbc_det: usbcdetgrp {
 		fsl,pins = <
-			/* USBC_DET */
+			/* SODIMM 137 / USBC_DET */
 			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
-			/* USBC_DET_EN */
-			MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26	0x0f058
 			/* USBC_DET_OVERWRITE */
 			MX6QDL_PAD_RGMII_RXC__GPIO6_IO30	0x0f058
+			/* USBC_DET_EN */
+			MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26	0x0f058
 		>;
 	};
 
-	pinctrl_usbc_id_1: usbc_id-1 {
+	pinctrl_usbc_id_1: usbcid1grp {
 		fsl,pins = <
 			/* USBC_ID */
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
 		>;
 	};
 
+	pinctrl_usbh_oc_1: usbhoc1grp {
+		fsl,pins = <
+			/* USBH_OC */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x17071
@@ -719,6 +1109,40 @@
 		>;
 	};
 
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170b1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100b1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170f1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100f1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
+		>;
+	};
+
+	/* avoid backfeeding with removed card power */
+	pinctrl_usdhc1_sleep: usdhc1sleepgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x3000
+			MX6QDL_PAD_SD1_CLK__SD1_CLK	0x3000
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0	0x3000
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1	0x3000
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2	0x3000
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3	0x3000
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
@@ -757,135 +1181,136 @@
 		>;
 	};
 
-	pinctrl_weim_sram: weimsramgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
-			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
-			/* Data */
-			MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00	0x1b0b0
-			MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT4__EIM_DATA02	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT5__EIM_DATA03	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT6__EIM_DATA04	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT7__EIM_DATA05	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT8__EIM_DATA06	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT9__EIM_DATA07	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT12__EIM_DATA08	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT13__EIM_DATA09	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT14__EIM_DATA10	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT15__EIM_DATA11	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT16__EIM_DATA12	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT17__EIM_DATA13	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT18__EIM_DATA14	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT19__EIM_DATA15	0x1b0b0
-			/* Address */
-			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
-			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
-			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
-			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
-			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
-			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
-			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
-			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
-			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
-			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
-			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
-			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
-			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
-			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
-			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
-			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
-		>;
-	};
-
-	pinctrl_weim_rdnwr: weimrdnwr {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_CLK__GPIO1_IO10		0x0040
-			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23	0x130b0
-		>;
-	};
-
-	pinctrl_weim_npwe: weimnpwe {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x0040
-			MX6QDL_PAD_RGMII_TD2__GPIO6_IO22	0x130b0
-		>;
-	};
-
 	/* ADDRESS[16:18] [25] used as GPIO */
-	pinctrl_weim_gpio_1: weimgpio-1 {
+	pinctrl_weim_gpio_1: weimgpio1grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
 			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
 		>;
 	};
 
 	/* ADDRESS[19:24] used as GPIO */
-	pinctrl_weim_gpio_2: weimgpio-2 {
+	pinctrl_weim_gpio_2: weimgpio2grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
-			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
 		>;
 	};
 
 	/* DATA[16:31] used as GPIO */
-	pinctrl_weim_gpio_3: weimgpio-3 {
+	pinctrl_weim_gpio_3: weimgpio3grp {
 		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
 			MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x1b0b0
 			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b0
-			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0
-			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
-			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b0
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b0
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
 			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0
-			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
 			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x1b0b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0
 			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x1b0b0
-			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
-			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x1b0b0
-			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
-			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
-			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b0
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b0
+			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
 		>;
 	};
 
 	/* DQM[0:3] used as GPIO */
-	pinctrl_weim_gpio_4: weimgpio-4 {
+	pinctrl_weim_gpio_4: weimgpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0
 			MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0
-			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
+			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
 		>;
 	};
 
 	/* RDY used as GPIO */
-	pinctrl_weim_gpio_5: weimgpio-5 {
+	pinctrl_weim_gpio_5: weimgpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x1b0b0
 		>;
 	};
 
 	/* ADDRESS[16] DATA[30] used as GPIO */
-	pinctrl_weim_gpio_6: weimgpio-6 {
+	pinctrl_weim_gpio_6: weimgpio6grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
 			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
+	pinctrl_weim_npwe: weimnpwegrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD2__GPIO6_IO22	0x130b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x0040
+		>;
+	};
+
+	pinctrl_weim_sram: weimsramgrp {
+		fsl,pins = <
+			/* Data */
+			MX6QDL_PAD_CSI0_DAT4__EIM_DATA02	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__EIM_DATA03	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__EIM_DATA04	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT7__EIM_DATA05	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT8__EIM_DATA06	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT9__EIM_DATA07	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT12__EIM_DATA08	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__EIM_DATA09	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__EIM_DATA10	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__EIM_DATA11	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__EIM_DATA12	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__EIM_DATA13	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__EIM_DATA14	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__EIM_DATA15	0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00	0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01	0x1b0b0
+			/* Address */
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
+			/* Ctrl */
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
+		>;
+	};
+
+	pinctrl_weim_rdnwr: weimrdnwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23	0x130b0
+			MX6QDL_PAD_SD2_CLK__GPIO1_IO10		0x0040
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
index e3be453d8a4a..1e530d892b76 100644
--- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
@@ -55,12 +55,12 @@
 		pinctrl-0 = <&pinctrl_cubox_i_ir>;
 	};
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
 
-		front {
+		led-1 {
 			active-low;
 			label = "imx6:red:front";
 			max-brightness = <248>;
@@ -233,6 +233,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dfi-fs700-m60.dtsi
index ebe7a8bddf04..0a6c3a092b34 100644
--- a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dfi-fs700-m60.dtsi
@@ -2,26 +2,18 @@
 #include <dt-bindings/gpio/gpio.h>
 
 / {
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		dummy_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "dummy-supply";
-		};
+	dummy_reg: regulator-dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "dummy-supply";
+	};
 
-		reg_usb_otg_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
 	};
 
 	chosen {
@@ -30,12 +22,12 @@
 };
 
 &ecspi3 {
-	cs-gpios = <&gpio4 24 0>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "sst,sst25vf040b", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi
new file mode 100644
index 000000000000..702cd4a1b2e6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 DH electronics GmbH
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/*
+ * Special SoM hardware required which uses the pins from micro SD card. The
+ * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2
+ * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. Therefore the micro SD
+ * card must be disabled and the uart1 rts/cts must be output on other DHCOM
+ * pins, see uart1 and usdhc3 node below.
+ */
+&can2 {
+	status = "okay";
+};
+
+&gpio1 {
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the i.MX6 UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <18 0>; /* GPIO Q */
+		line-name = "rs485-rx-en";
+		output-low;
+	};
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "DRC02-In1", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "DHCOM-E", "DRC02-In2", "DHCOM-H",
+		"DHCOM-I", "DRC02-HW0", "", "", "", "", "", "",
+		"", "", "", "", "DRC02-Out1", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"", "", "", "DRC02-Out2", "", "", "SOM-HW1", "",
+		"", "", "", "", "", "", "DRC02-HW2", "DRC02-HW1",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&uart1 {
+	/*
+	 * Due to the use of can2 the signals for can2 Tx and Rx are routed to
+	 * DHCOM UART1 rts/cts pins. Therefore this UART have to use DHCOM GPIOs
+	 * for rts/cts. So configure DHCOM GPIO I as rts and GPIO M as cts.
+	 */
+	/delete-property/ uart-has-rtscts;
+	cts-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; /* GPIO M */
+	pinctrl-0 = <&pinctrl_uart1 &pinctrl_dhcom_i &pinctrl_dhcom_m>;
+	pinctrl-names = "default";
+	rts-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+};
+
+&uart5 {
+	/*
+	 * On DRC02 this UART is used as RS485 interface and RS485_TX_En is
+	 * controlled by DHCOM GPIO P. So remove rts/cts pins and the property
+	 * uart-has-rtscts from this UART and add the DHCOM GPIO P pin via
+	 * rts-gpios. The RS485_RX_En is controlled by DHCOM GPIO Q, see gpio1
+	 * node above.
+	 */
+	/delete-property/ uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	pinctrl-0 = <&pinctrl_uart5_core &pinctrl_dhcom_p &pinctrl_dhcom_q>;
+	pinctrl-names = "default";
+	rts-gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>; /* GPIO P */
+};
+
+&usbh1 {
+	disable-over-current;
+};
+
+&usdhc2 { /* SD card */
+	status = "okay";
+};
+
+&usdhc3 {
+	/*
+	 * Due to the use of can2 the micro SD card on module have to be
+	 * disabled, because the pins SD3_DAT0 and SD3_DAT1 are muxed as
+	 * can2 Tx and Rx.
+	 */
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl-0 = <
+			/*
+			 * The following DHCOM GPIOs are used on this board.
+			 * Therefore, they have been removed from the list below.
+			 * I: uart1 rts
+			 * M: uart1 cts
+			 * P: uart5 rs485-tx-en
+			 * Q: uart5 rs485-rx-en
+			 */
+			&pinctrl_hog_base
+			&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
+			&pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
+			&pinctrl_dhcom_g &pinctrl_dhcom_h
+			&pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
+			&pinctrl_dhcom_n &pinctrl_dhcom_o
+			&pinctrl_dhcom_r
+			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
+			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
+		>;
+	pinctrl-names = "default";
+
+	pinctrl_uart5_core: uart5-core-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA	0x1b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-pdk2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-pdk2.dtsi
new file mode 100644
index 000000000000..6248b126b557
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-pdk2.dtsi
@@ -0,0 +1,335 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2021 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		compatible = "fixed-clock";
+	};
+
+	display_bl: display-bl {
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		compatible = "pwm-backlight";
+		default-brightness-level = <8>;
+		enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; /* GPIO G */
+		pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
+		status = "okay";
+	};
+
+	lcd_display: disp0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif &pinctrl_dhcom_g>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	gpio-keys {
+		#size-cells = <0>;
+		compatible = "gpio-keys";
+
+		button-0 {
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* GPIO A */
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			pinctrl-0 = <&pinctrl_dhcom_a>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+
+		button-1 {
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* GPIO B */
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			pinctrl-0 = <&pinctrl_dhcom_b>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+
+		button-2 {
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; /* GPIO C */
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			pinctrl-0 = <&pinctrl_dhcom_c>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+
+		button-3 {
+			gpios = <&gpio6 3 GPIO_ACTIVE_LOW>; /* GPIO D */
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			pinctrl-0 = <&pinctrl_dhcom_d>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		/*
+		 * Disable led-5, because GPIO E is
+		 * already used as touch interrupt.
+		 */
+		led-5 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* GPIO E */
+			pinctrl-0 = <&pinctrl_dhcom_e>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
+		led-6 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>; /* GPIO F */
+			pinctrl-0 = <&pinctrl_dhcom_f>;
+			pinctrl-names = "default";
+		};
+
+		led-7 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* GPIO H */
+			pinctrl-0 = <&pinctrl_dhcom_h>;
+			pinctrl-names = "default";
+		};
+
+		led-8 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+			pinctrl-0 = <&pinctrl_dhcom_i>;
+			pinctrl-names = "default";
+		};
+	};
+
+	panel {
+		backlight = <&display_bl>;
+		compatible = "edt,etm0700g0edh6";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	sound {
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx-sgtl5000";
+		mux-ext-port = <3>;
+		mux-int-port = <1>;
+		ssi-controller = <&ssi1>;
+	};
+};
+
+&audmux {
+	pinctrl-0 = <&pinctrl_audmux_ext>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "disabled";
+};
+
+/* 1G ethernet */
+/delete-node/ &ethphy0;
+&fec {
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy7>;
+	pinctrl-0 = <&pinctrl_enet_1G>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy7: ethernet-phy@7 { /* KSZ 9021 */
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_ethphy7>;
+			pinctrl-names = "default";
+			reg = <7>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			rxdv-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+			txen-skew-ps = <0>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	sgtl5000: codec@a {
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&sw2_reg>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		pinctrl-0 = <&pinctrl_dhcom_e>;
+		pinctrl-names = "default";
+		reg = <0x38>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pcie {
+	pinctrl-0 = <&pinctrl_pcie &pinctrl_dhcom_j>;
+	reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>; /* GPIO J */
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+};
+
+&usdhc2 { /* SD card */
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <
+			/*
+			 * The following DHCOM GPIOs are used on this board.
+			 * Therefore, they have been removed from the list below.
+			 * A: key TA1
+			 * B: key TA2
+			 * C: key TA3
+			 * D: key TA4
+			 * E: touchscreen
+			 * F: led6
+			 * G: backlight enable
+			 * H: led7
+			 * I: led8
+			 * J: PCIe reset
+			 */
+			&pinctrl_hog_base
+			&pinctrl_dhcom_k &pinctrl_dhcom_l
+			&pinctrl_dhcom_m &pinctrl_dhcom_n &pinctrl_dhcom_o
+			&pinctrl_dhcom_p &pinctrl_dhcom_q &pinctrl_dhcom_r
+			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
+			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
+		>;
+	pinctrl-names = "default";
+
+	pinctrl_audmux_ext: audmux-ext-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+		>;
+	};
+
+	pinctrl_enet_1G: enet-1G-grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
+		>;
+	};
+
+	pinctrl_ethphy7: ethphy7-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0xb1 /* WOL */
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0xb0 /* Reset */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0xb1 /* Int */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-picoitx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-picoitx.dtsi
new file mode 100644
index 000000000000..4cd4cb9543c8
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-picoitx.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 DH electronics GmbH
+ */
+
+#include <dt-bindings/leds/common.h>
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_YELLOW>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+			pinctrl-0 = <&pinctrl_dhcom_i>;
+			pinctrl-names = "default";
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "DHCOM-A", "", "DHCOM-B", "PicoITX-In2", "", "",
+		"", "", "", "", "", "", "", "",
+		"DHCOM-R", "DHCOM-S", "DHCOM-Q", "DHCOM-T", "DHCOM-U", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "PicoITX-In1", "DHCOM-INT", "DHCOM-H",
+		"DHCOM-I", "PicoITX-HW2", "", "", "", "", "", "",
+		"", "", "", "", "PicoITX-Out1", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"", "", "", "PicoITX-Out2", "", "", "SOM-HW1", "",
+		"", "", "", "", "", "", "PicoITX-HW0", "PicoITX-HW1",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&iomuxc {
+	pinctrl-0 = <
+			/*
+			 * The following DHCOM GPIOs are used on this board.
+			 * Therefore, they have been removed from the list below.
+			 * I: yellow led
+			 */
+			&pinctrl_hog_base
+			&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
+			&pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
+			&pinctrl_dhcom_g &pinctrl_dhcom_h
+			&pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
+			&pinctrl_dhcom_m &pinctrl_dhcom_n &pinctrl_dhcom_o
+			&pinctrl_dhcom_p &pinctrl_dhcom_q &pinctrl_dhcom_r
+			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
+			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
+		>;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-som.dtsi
new file mode 100644
index 000000000000..eaa87b333164
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-som.dtsi
@@ -0,0 +1,850 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2021 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c1;
+		i2c2 = &i2c3;
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc4;
+		mmc3 = &usdhc1;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+		serial0 = &uart1;
+		serial1 = &uart5;
+		serial2 = &uart4;
+		serial3 = &uart2;
+		serial4 = &uart3;
+	};
+
+	memory@10000000 { /* Appropriate memory size will be filled by U-Boot */
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	reg_3p3v: regulator-3P3V {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3P3V";
+	};
+
+	reg_eth_vio: regulator-eth-vio {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 7 0>;
+		pinctrl-0 = <&pinctrl_enet_vio>;
+		pinctrl-names = "default";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "eth_vio";
+		vin-supply = <&sw2_reg>;
+	};
+
+	/* OE pin of the latch is low active */
+	reg_latch_oe_on: regulator-latch-oe-on {
+		compatible = "regulator-fixed";
+		gpio = <&gpio3 22 0>;
+		regulator-always-on;
+		regulator-name = "latch_oe_on";
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 31 0>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "usb_h1_vbus";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "usb_otg_vbus";
+	};
+};
+
+&can1 {
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * Special SoM hardware required which uses the pins from micro SD card. The
+ * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2
+ * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. So to enable can2 on
+ * the board device tree file, the micro SD card must be disabled and the uart1
+ * rts/cts must be disabled or output on other DHCOM pins.
+ */
+&can2 {
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 { /* S25FL116K */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		m25p,fast-read;
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&fec {
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	pinctrl-0 = <&pinctrl_enet_100M>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
+			compatible = "ethernet-phy-id0007.c0f0",
+				     "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio4>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reg = <0>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "DHCOM-A", "", "DHCOM-B", "DHCOM-C", "", "",
+		"", "", "", "", "", "", "", "",
+		"DHCOM-R", "DHCOM-S", "DHCOM-Q", "DHCOM-T", "DHCOM-U", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"SOM-HW2", "", "", "SOM-HW0", "", "SOM-MEM1", "SOM-MEM0", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "DHCOM-G", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "DHCOM-E", "DHCOM-INT", "DHCOM-H",
+		"DHCOM-I", "DHCOM-L", "", "", "", "", "", "",
+		"", "", "", "", "DHCOM-F", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "DHCOM-V", "DHCOM-W", "", "DHCOM-O", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"", "", "", "DHCOM-D", "", "", "SOM-HW1", "",
+		"", "", "", "", "", "", "DHCOM-J", "DHCOM-K",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio7 {
+	gpio-line-names =
+		"DHCOM-M", "DHCOM-N", "", "", "", "", "", "",
+		"", "", "", "", "", "DHCOM-P", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	/*
+	 * Info: According to erratum ERR007805 clock frequency limit is 375000.
+	 * The erratum for i.MX6S/DL is here [1] and for i.MX6Q/D is here [2].
+	 * [1] https://www.nxp.com/docs/en/errata/IMX6SDLCE.pdf
+	 * [2] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
+	 */
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c2 {
+	/* Info: Clock frequency limit is 375000 (for details see i2c1) */
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	/* Info: Clock frequency limit is 375000 (for details see i2c1) */
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	ltc3676: pmic@3c {
+		compatible = "lltc,ltc3676";
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+		reg = <0x3c>;
+
+		regulators {
+			sw1_reg: sw1 {
+				lltc,fb-voltage-divider = <100000 110000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1527272>;
+				regulator-min-microvolt = <787500>;
+				regulator-ramp-delay = <7000>;
+				regulator-suspend-mem-microvolt = <1040000>;
+			};
+
+			sw2_reg: sw2 {
+				lltc,fb-voltage-divider = <100000 28000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3657142>;
+				regulator-min-microvolt = <1885714>;
+				regulator-ramp-delay = <7000>;
+			};
+
+			sw3_reg: sw3 {
+				lltc,fb-voltage-divider = <100000 110000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1527272>;
+				regulator-min-microvolt = <787500>;
+				regulator-ramp-delay = <7000>;
+				regulator-suspend-mem-microvolt = <980000>;
+			};
+
+			sw4_reg: sw4 {
+				lltc,fb-voltage-divider = <100000 93100>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1659291>;
+				regulator-min-microvolt = <855571>;
+				regulator-ramp-delay = <7000>;
+			};
+
+			ldo1_reg: ldo1 {
+				lltc,fb-voltage-divider = <102000 29400>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3240306>;
+				regulator-min-microvolt = <3240306>;
+			};
+
+			ldo2_reg: ldo2 {
+				lltc,fb-voltage-divider = <100000 41200>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2484708>;
+				regulator-min-microvolt = <2484708>;
+			};
+		};
+	};
+
+	touchscreen@49 { /* TSC2004 */
+		compatible = "ti,tsc2004";
+		interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-0 = <&pinctrl_tsc2004>;
+		pinctrl-names = "default";
+		reg = <0x49>;
+		vio-supply = <&reg_3p3v>;
+		status = "disabled";
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+
+	rtc_i2c: rtc@56 {
+		compatible = "microcrystal,rv3029";
+		interrupt-parent = <&gpio7>;
+		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-0 = <&pinctrl_rtc>;
+		pinctrl-names = "default";
+		reg = <0x56>;
+	};
+};
+
+&pcie {
+	pinctrl-0 = <&pinctrl_pcie>;
+	pinctrl-names = "default";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-names = "default";
+};
+
+&reg_arm {
+	vin-supply = <&sw3_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&sw1_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1_reg>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&sw2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&sw2_reg>;
+};
+
+&uart1 { /* DHCOM UART1 */
+	dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+	dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 { /* DHCOM UART3 */
+	pinctrl-0 = <&pinctrl_uart4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart5 { /* DHCOM UART2 */
+	pinctrl-0 = <&pinctrl_uart5>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	dr_mode = "host";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	pinctrl-names = "default";
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	dr_mode = "otg";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	pinctrl-names = "default";
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+&usdhc2 { /* External SD card via DHCOM */
+	cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&usdhc3 { /* Micro SD card on module */
+	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	keep-power-in-suspend;
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usdhc4 { /* eMMC on module */
+	bus-width = <8>;
+	keep-power-in-suspend;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&weim {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	fsl,weim-cs-gpr = <&gpr>;
+	pinctrl-0 = <&pinctrl_weim &pinctrl_weim_cs0 &pinctrl_weim_cs1>;
+	pinctrl-names = "default";
+	/* It is necessary to setup 2x 64MB otherwise setting gpr fails */
+	ranges = <0 0 0x08000000 0x04000000>, /* CS0 */
+		 <1 0 0x0c000000 0x04000000>; /* CS1 */
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl-0 = <
+			&pinctrl_hog_base
+			&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
+			&pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
+			&pinctrl_dhcom_g &pinctrl_dhcom_h &pinctrl_dhcom_i
+			&pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
+			&pinctrl_dhcom_m &pinctrl_dhcom_n &pinctrl_dhcom_o
+			&pinctrl_dhcom_p &pinctrl_dhcom_q &pinctrl_dhcom_r
+			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
+			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
+		>;
+	pinctrl-names = "default";
+
+	pinctrl_hog_base: hog-base-grp {
+		fsl,pins = <
+			/* GPIOs for memory coding */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x120b0
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x120b0
+			/* GPIOs for hardware coding */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0x120b0
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x120b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x120b0
+		>;
+	};
+
+	/* DHCOM GPIOs */
+	pinctrl_dhcom_a: dhcom-a-grp {
+		fsl,pins = <MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x400120b0>;
+	};
+
+	pinctrl_dhcom_b: dhcom-b-grp {
+		fsl,pins = <MX6QDL_PAD_GPIO_4__GPIO1_IO04	0x400120b0>;
+	};
+
+	pinctrl_dhcom_c: dhcom-c-grp {
+		fsl,pins = <MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x400120b0>;
+	};
+
+	pinctrl_dhcom_d: dhcom-d-grp {
+		fsl,pins = <MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03	0x400120b0>;
+	};
+
+	pinctrl_dhcom_e: dhcom-e-grp {
+		fsl,pins = <MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x400120b0>;
+	};
+
+	pinctrl_dhcom_f: dhcom-f-grp {
+		fsl,pins = <MX6QDL_PAD_DI0_PIN4__GPIO4_IO20	0x400120b0>;
+	};
+
+	pinctrl_dhcom_g: dhcom-g-grp {
+		fsl,pins = <MX6QDL_PAD_EIM_D27__GPIO3_IO27	0x400120b0>;
+	};
+
+	pinctrl_dhcom_h: dhcom-h-grp {
+		fsl,pins = <MX6QDL_PAD_KEY_ROW0__GPIO4_IO07	0x400120b0>;
+	};
+
+	pinctrl_dhcom_i: dhcom-i-grp {
+		fsl,pins = <MX6QDL_PAD_KEY_COL1__GPIO4_IO08	0x400120b0>;
+	};
+
+	pinctrl_dhcom_j: dhcom-j-grp {
+		fsl,pins = <MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x400120b0>;
+	};
+
+	pinctrl_dhcom_k: dhcom-k-grp {
+		fsl,pins = <MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x400120b0>;
+	};
+
+	pinctrl_dhcom_l: dhcom-l-grp {
+		fsl,pins = <MX6QDL_PAD_KEY_ROW1__GPIO4_IO09	0x400120b0>;
+	};
+
+	pinctrl_dhcom_m: dhcom-m-grp {
+		fsl,pins = <MX6QDL_PAD_SD3_DAT5__GPIO7_IO00	0x400120b0>;
+	};
+
+	pinctrl_dhcom_n: dhcom-n-grp {
+		fsl,pins = <MX6QDL_PAD_SD3_DAT4__GPIO7_IO01	0x400120b0>;
+	};
+
+	pinctrl_dhcom_o: dhcom-o-grp {
+		fsl,pins = <MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x400120b0>;
+	};
+
+	pinctrl_dhcom_p: dhcom-p-grp {
+		fsl,pins = <MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x400120b0>;
+	};
+
+	pinctrl_dhcom_q: dhcom-q-grp {
+		fsl,pins = <MX6QDL_PAD_SD1_CMD__GPIO1_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_r: dhcom-r-grp {
+		fsl,pins = <MX6QDL_PAD_SD1_DAT0__GPIO1_IO16	0x400120b0>;
+	};
+
+	pinctrl_dhcom_s: dhcom-s-grp {
+		fsl,pins = <MX6QDL_PAD_SD1_DAT1__GPIO1_IO17	0x400120b0>;
+	};
+
+	pinctrl_dhcom_t: dhcom-t-grp {
+		fsl,pins = <MX6QDL_PAD_SD1_DAT2__GPIO1_IO19	0x400120b0>;
+	};
+
+	pinctrl_dhcom_u: dhcom-u-grp {
+		fsl,pins = <MX6QDL_PAD_SD1_CLK__GPIO1_IO20	0x400120b0>;
+	};
+
+	pinctrl_dhcom_v: dhcom-v-grp {
+		fsl,pins = <MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_w: dhcom-w-grp {
+		fsl,pins = <MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x400120b0>;
+	};
+
+	pinctrl_dhcom_int: dhcom-int-grp {
+		fsl,pins = <MX6QDL_PAD_KEY_COL0__GPIO4_IO06	0x400120b0>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet_100M: enet-100M-grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet_vio: enet-vio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x120b0
+		>;
+	};
+
+	pinctrl_ethphy0: ethphy0-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0xb0 /* Reset */
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0xb1 /* Int */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX	0x1b0b0
+			MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3-gpio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x38
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x38
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x38
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x38
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x38
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x38
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x38
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x38
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x38
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x38
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x38
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x38
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x38
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x38
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x38
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x38
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x38
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x38
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x38
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x38
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x38
+		>;
+	};
+
+	pinctrl_pcie: pcie-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1 /* Wake */
+		>;
+	};
+
+	pinctrl_pmic: pmic-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_rtc: rtc-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x120b0
+		>;
+	};
+
+	pinctrl_tsc2004: tsc2004-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x120b0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__UART1_CTS_B		0x4001b0b1
+			MX6QDL_PAD_EIM_D20__UART1_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x4001b0b1
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24		0x4001b0b1
+			MX6QDL_PAD_EIM_D25__GPIO3_IO25		0x4001b0b1
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x4001b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B	0x4001b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120b0
+			MX6QDL_PAD_EIM_D30__USB_H1_OC		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotg-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x120b0
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x120b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+
+	pinctrl_weim: weim-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0a6
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0a6
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0a6
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0a6
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0a6
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0a6
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0a6
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0a6
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0a6
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0a6
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0a6
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0a6
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0a6
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0a6
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0a6
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0a6
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
+			MX6QDL_PAD_EIM_LBA__EIM_LBA_B		0xb060 /* LE */
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0a6
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0a6 /* WE */
+		>;
+	};
+
+	pinctrl_weim_cs0: weim-cs0-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0b1
+		>;
+	};
+
+	pinctrl_weim_cs1: weim-cs1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS1__EIM_CS1_B		0xb0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-ds.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-ds.dtsi
new file mode 100644
index 000000000000..f7e517555697
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-ds.dtsi
@@ -0,0 +1,458 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
+//
+// Based on imx6qdl-sabresd.dtsi which is:
+// Copyright 2012 Freescale Semiconductor, Inc.
+// Copyright 2011 Linaro Ltd.
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-0 {
+			gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vsync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&ov2659_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_gpio>;
+	status = "okay";
+
+	m25p80: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p80", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
+			reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+		};
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_cec>;
+	ddc-i2c-bus = <&i2c3>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pfuze100: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	ov2659: camera@30 {
+		compatible = "ovti,ov2659";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov2659>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xvclk";
+		reg = <0x30>;
+		powerdown-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		status = "okay";
+
+		port {
+			ov2659_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				link-frequencies = /bits/ 64 <70000000>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+		>;
+	};
+
+	pinctrl_ecspi1_gpio: ecspi1grpgpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10         0x1b0b0
+		>;
+	};
+
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1f8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+		>;
+	};
+
+	pinctrl_ov2659: ov2659grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_16__GPIO7_IO11		0x1b0b0
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x1b0b0
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17059
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x10059
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x17059
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x17059
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x17059
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_gpio: usdhc1grpgpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0
+		>;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+	status = "disabled";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon-avari.dtsi
index 828cf3e39784..5587069b6052 100644
--- a/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon-avari.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
@@ -54,7 +54,7 @@
 	clk_codec: clock-codec {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency  = <12000000>;
+		clock-frequency = <12000000>;
 	};
 
 	sound {
@@ -126,7 +126,7 @@
 		compatible = "nxp,pca8574";
 		reg = <0x3a>;
 		gpio-controller;
-		#gpio-cells = <1>;
+		#gpio-cells = <2>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-emcon.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
index 70d26616d771..a63e73adc1fc 100644
--- a/arch/arm/boot/dts/imx6qdl-emcon.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
@@ -46,14 +46,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_som_leds>;
 
-		green {
+		led-green {
 			label = "som:green";
 			gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			default-state = "on";
 		};
 
-		red {
+		led-red {
 			label = "som:red";
 			gpios = <&gpio3 1 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
@@ -168,8 +168,8 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>,
-		<&gpio2 27 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>,
+		<&gpio2 27 GPIO_ACTIVE_LOW>;
 };
 
 &ecspi4 {
@@ -737,14 +737,17 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw51xx.dtsi
index 419a7cdc8ab5..e75e1a5364b8 100644
--- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw51xx.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -19,19 +21,64 @@
 		bootargs = "console=ttymxc1,115200";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
@@ -102,6 +149,103 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_an1";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -126,13 +270,6 @@
 		pagesize = <16>;
 	};
 
-	gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	rtc: ds1672@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -387,6 +524,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x0001b0b0 /* GSC_IRQ# */
 		>;
 	};
 
@@ -488,6 +626,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0 /* OTG_PWR_EN */
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x17059
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
index 1a9a9d98f284..535679c27d6f 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -28,25 +30,70 @@
 		default-brightness-level = <7>;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -90,6 +137,16 @@
 		regulator-always-on;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg_vbus";
@@ -123,6 +180,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -134,7 +192,7 @@
 };
 
 &ecspi3 {
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
@@ -165,6 +223,109 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+
+			channel@29 {
+				gw,mode = <1>;
+				reg = <0x29>;
+				label = "vdd_an1";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -189,13 +350,6 @@
 		pagesize = <16>;
 	};
 
-	gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	rtc: ds1672@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -273,7 +427,7 @@
 
 			/* VDD_AUD_1P8: Audio codec */
 			reg_aud_1p8v: ldo3 {
-				regulator-name = "vdd1p8";
+				regulator-name = "vdd1p8a";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -301,6 +455,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -313,6 +468,11 @@
 		interrupts = <12 2>;
 		wakeup-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
 	};
+
+	accel@1e {
+		compatible = "nxp,fxos8700";
+		reg = <0x1e>;
+	};
 };
 
 &ldb {
@@ -360,6 +520,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -463,7 +624,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -499,6 +659,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
@@ -552,6 +713,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
@@ -578,6 +745,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x1b0b0 /* OTG_PWR_EN */
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x17059
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
index 54b2beadd7a2..3e1c572af582 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -28,25 +30,70 @@
 		default-brightness-level = <7>;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -82,6 +129,16 @@
 		regulator-always-on;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_usb_h1_vbus: regulator-usb-h1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_h1_vbus";
@@ -123,6 +180,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -158,6 +216,115 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+
+			channel@26 {
+				gw,mode = <1>;
+				reg = <0x26>;
+				label = "vdd_gps";
+			};
+
+			channel@29 {
+				gw,mode = <1>;
+				reg = <0x29>;
+				label = "vdd_an1";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -182,13 +349,6 @@
 		pagesize = <16>;
 	};
 
-	gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	rtc: ds1672@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -292,6 +452,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -304,6 +465,11 @@
 		interrupts = <11 2>;
 		wakeup-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 	};
+
+	accel@1e {
+		compatible = "nxp,fxos8700";
+		reg = <0x1e>;
+	};
 };
 
 &ldb {
@@ -351,6 +517,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -445,7 +612,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -481,6 +647,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
@@ -535,6 +702,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
index 1b6c1331c220..0ffa0357a6fa 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/sound/fsl-imx-audmux.h>
 
 / {
@@ -29,25 +31,70 @@
 		default-brightness-level = <7>;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -67,47 +114,47 @@
 		status = "okay";
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	reg_1p0v: regulator-1p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P0V";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-always-on;
+	};
 
-		reg_1p0v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "1P0V";
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
-		reg_usb_h1_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound-analog {
@@ -130,7 +177,7 @@
 	pinctrl-0 = <&pinctrl_audmux>; /* AUD4<->sgtl5000 */
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -142,7 +189,7 @@
 		>;
 	};
 
-	aud5 {
+	mux-aud5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -153,6 +200,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -164,7 +212,7 @@
 };
 
 &ecspi2 {
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
@@ -195,6 +243,115 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+
+			channel@26 {
+				gw,mode = <1>;
+				reg = <0x26>;
+				label = "vdd_gps";
+			};
+		};
+
+		fan-controller@2c {
+			compatible = "gw,gsc-fan";
+			reg = <0x2c>;
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -219,13 +376,6 @@
 		pagesize = <16>;
 	};
 
-	gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	rtc: ds1672@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -238,7 +388,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -349,6 +499,7 @@
 	sgtl5000: audio-codec@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&sw4_reg>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -361,6 +512,11 @@
 		interrupts = <12 2>;
 		wakeup-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
 	};
+
+	accel@1e {
+		compatible = "nxp,fxos8700";
+		reg = <0x1e>;
+	};
 };
 
 &ldb {
@@ -414,6 +570,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default", "state_dio";
 	pinctrl-0 = <&pinctrl_pwm4_backlight>;
 	pinctrl-1 = <&pinctrl_pwm4_dio>;
@@ -530,7 +687,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -566,6 +722,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
@@ -628,6 +785,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
@@ -654,6 +817,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0 /* PWR_EN */
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x17059
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw551x.dtsi
index c38e86eedcc0..29960d1cf6a0 100644
--- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw551x.dtsi
@@ -47,6 +47,8 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/media/tda1997x.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/sound/fsl-imx-audmux.h>
 
 / {
@@ -63,12 +65,57 @@
 		bootargs = "console=ttymxc1,115200";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
 			default-state = "on";
@@ -110,7 +157,7 @@
 		simple-audio-card,frame-master = <&sound_codec>;
 
 		sound_cpu: simple-audio-card,cpu {
-			sound-dai = <&ssi2>;
+			sound-dai = <&ssi1>;
 		};
 
 		sound_codec: simple-audio-card,codec {
@@ -124,7 +171,7 @@
 	pinctrl-0 = <&pinctrl_audmux>; /* AUD5<->tda1997x */
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -136,7 +183,7 @@
 		>;
 	};
 
-	aud5 {
+	mux-aud5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -167,6 +214,97 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8a";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0b";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -191,13 +329,6 @@
 		pagesize = <16>;
 	};
 
-	gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	rtc: ds1672@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -464,6 +595,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw552x.dtsi
index dc646b72b59a..77ae611b817a 100644
--- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw552x.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -20,25 +22,70 @@
 		bootargs = "console=ttymxc1,115200";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -92,6 +139,103 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -116,13 +260,6 @@
 		pagesize = <16>;
 	};
 
-	gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	rtc: ds1672@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -258,6 +395,14 @@
 	status = "okay";
 };
 
+&usbotg {
+	vbus-supply = <&reg_5p0v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
@@ -297,6 +442,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
@@ -359,6 +505,12 @@
 		>;
 	};
 
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x13059
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0
diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw553x.dtsi
index a1066897be18..7f16c602cc07 100644
--- a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw553x.dtsi
@@ -46,6 +46,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -61,19 +63,64 @@
 		stdout-path = &uart2;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
@@ -130,11 +177,101 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	gpio: pca9555@23 {
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8a";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0b";
+			};
+
+			channel@26 {
+				gw,mode = <1>;
+				reg = <0x26>;
+				label = "vdd_an1";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
 		compatible = "nxp,pca9555";
 		reg = <0x23>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
 	};
 
 	eeprom1: eeprom@50 {
@@ -173,6 +310,25 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
+	magn@1c {
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mag>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	imu@6a {
+		compatible = "st,lsm9ds1-imu";
+		reg = <0x6a>;
+		st,drdy-int-pin = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	ltc3676: pmic@3c {
 		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
@@ -409,6 +565,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
@@ -426,6 +583,12 @@
 		>;
 	};
 
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
+		>;
+	};
+
 	pinctrl_ipu1_csi0: ipu1csi0grp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
@@ -449,6 +612,12 @@
 		>;
 	};
 
+	pinctrl_mag: maggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+		>;
+	};
+
 	pinctrl_pcie: pciegrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
@@ -518,6 +687,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0 /* OTG_PWR_EN */
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x17059
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
index e8e36dfd0a6b..46cf4080fec3 100644
--- a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
@@ -47,6 +47,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -88,25 +89,70 @@
 		default-on;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -205,7 +251,7 @@
 };
 
 &ecspi3 {
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
@@ -243,6 +289,115 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_an1";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+
+			channel@26 {
+				gw,mode = <1>;
+				reg = <0x26>;
+				label = "vdd_gps";
+			};
+
+			channel@29 {
+				gw,mode = <1>;
+				reg = <0x29>;
+				label = "vdd_an2";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
 	eeprom1: eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -267,13 +422,6 @@
 		pagesize = <16>;
 	};
 
-	pca9555: gpio@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
 	ds1672: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
@@ -295,6 +443,15 @@
 		VDDIO-supply = <&reg_3p3v>;
 	};
 
+	magn@1c {
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mag>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+	};
+
 	tca8418: keypad@34 {
 		compatible = "ti,tca8418";
 		pinctrl-names = "default";
@@ -389,6 +546,16 @@
 			};
 		};
 	};
+
+	imu@6a {
+		compatible = "st,lsm9ds1-imu";
+		reg = <0x6a>;
+		st,drdy-int-pin = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+	};
 };
 
 &i2c3 {
@@ -452,6 +619,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -464,7 +632,6 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
 	rts-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
@@ -589,6 +756,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0xb0b1
 		>;
 	};
 
@@ -609,6 +777,12 @@
 		>;
 	};
 
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06	0x1b0b0
+		>;
+	};
+
 	pinctrl_keypad: keypadgrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11	0x0001b0b0 /* KEYPAD_IRQ# */
@@ -616,6 +790,12 @@
 		>;
 	};
 
+	pinctrl_mag: maggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09	0x1b0b0
+		>;
+	};
+
 	pinctrl_pcie: pciegrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31	0x1b0b0    /* PCI_RST# */
diff --git a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
index aee9221f0f29..a74cde050158 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
@@ -46,6 +46,8 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	chosen {
@@ -71,12 +73,57 @@
 		default-brightness-level = <100>;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio6 14 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -183,11 +230,101 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pca9555: gpio@23 {
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_an1";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
 		compatible = "nxp,pca9555";
 		reg = <0x23>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
 	};
 
 	eeprom1: eeprom@50 {
@@ -365,6 +502,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
index 6d21cc6a9d4b..1e723807ab4c 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
@@ -46,10 +46,17 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
 	aliases {
+		ethernet0 = &fec;
+		ethernet1 = &lan1;
+		ethernet2 = &lan2;
+		ethernet3 = &lan3;
+		ethernet4 = &lan4;
 		led0 = &led0;
 		led1 = &led1;
 		led2 = &led2;
@@ -68,25 +75,70 @@
 		default-brightness-level = <7>;
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -165,34 +217,72 @@
 			compatible = "marvell,mv88e6085";
 			reg = <0>;
 
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sw_phy0: ethernet-phy@0 {
+					reg = <0x0>;
+				};
+
+				sw_phy1: ethernet-phy@1 {
+					reg = <0x1>;
+				};
+
+				sw_phy2: ethernet-phy@2 {
+					reg = <0x2>;
+				};
+
+				sw_phy3: ethernet-phy@3 {
+					reg = <0x3>;
+				};
+			};
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				lan4: port@0 {
 					reg = <0>;
 					label = "lan4";
+					phy-handle = <&sw_phy0>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
-				port@1 {
+				lan3: port@1 {
 					reg = <1>;
 					label = "lan3";
+					phy-handle = <&sw_phy1>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
-				port@2 {
+				lan2: port@2 {
 					reg = <2>;
 					label = "lan2";
+					phy-handle = <&sw_phy2>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
-				port@3 {
+				lan1: port@3 {
 					reg = <3>;
 					label = "lan1";
+					phy-handle = <&sw_phy3>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
 				port@5 {
 					reg = <5>;
-					label = "cpu";
 					ethernet = <&fec>;
+					phy-mode = "rgmii-id";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
 				};
 			};
 		};
@@ -205,11 +295,101 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pca9555: gpio@23 {
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_an1";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
 		compatible = "nxp,pca9555";
 		reg = <0x23>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
 	};
 
 	eeprom1: eeprom@50 {
@@ -248,6 +428,15 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
+	magn@1c {
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mag>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+	};
+
 	ltc3676: pmic@3c {
 		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
@@ -320,6 +509,21 @@
 			};
 		};
 	};
+
+	crypto@60 {
+		compatible = "atmel,atecc508a";
+		reg = <0x60>;
+	};
+
+	imu@6a {
+		compatible = "st,lsm9ds1-imu";
+		reg = <0x6a>;
+		st,drdy-int-pin = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+	};
 };
 
 &i2c3 {
@@ -382,6 +586,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -484,6 +689,7 @@
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x0001b0b0 /* GSC_IRQ# */
 		>;
 	};
 
@@ -501,6 +707,18 @@
 		>;
 	};
 
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
+		>;
+	};
+
+	pinctrl_mag: maggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
+		>;
+	};
+
 	pinctrl_pcie: pciegrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0 /* PCIE RST */
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5907.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5907.dtsi
new file mode 100644
index 000000000000..955a51226eda
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5907.dtsi
@@ -0,0 +1,536 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	/* these are used by bootloader for disabling nodes */
+	aliases {
+		led0 = &led0;
+		led1 = &led1;
+		nand = &gpmi;
+		usb0 = &usbh1;
+		usb1 = &usbotg;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led0: led-user1 {
+			label = "user1";
+			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led1: led-user2 {
+			label = "user2";
+			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+			default-state = "off";
+		};
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	pps {
+		compatible = "pps-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pps>;
+		gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "5P0V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_an1";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	ds1672@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	adc@48 {
+		compatible = "ti,ads1015";
+		reg = <0x48>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <0>;
+			ti,datarate = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <0>;
+			ti,datarate = <5>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <0>;
+			ti,datarate = <5>;
+		};
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06		0x1b0b0
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x0001b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
+		>;
+	};
+
+	pinctrl_pps: ppsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5910.dtsi
new file mode 100644
index 000000000000..424dc7fcd533
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5910.dtsi
@@ -0,0 +1,663 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	/* these are used by bootloader for disabling nodes */
+	aliases {
+		led0 = &led0;
+		led1 = &led1;
+		led2 = &led2;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led0: led-user1 {
+			label = "user1";
+			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led1: led-user2 {
+			label = "user2";
+			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+			default-state = "off";
+		};
+
+		led2: led-user3 {
+			label = "user3";
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
+			default-state = "off";
+		};
+	};
+
+	pps {
+		compatible = "pps-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pps>;
+		gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "5P0V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_wl: regulator-wl {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_wl>;
+		compatible = "regulator-fixed";
+		regulator-name = "wl";
+		gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@6 {
+				gw,mode = <0>;
+				reg = <0x06>;
+				label = "temp";
+			};
+
+			channel@8 {
+				gw,mode = <3>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@82 {
+				gw,mode = <2>;
+				reg = <0x82>;
+				label = "vdd_vin";
+				gw,voltage-divider-ohms = <22100 1000>;
+				gw,voltage-offset-microvolt = <800000>;
+			};
+
+			channel@84 {
+				gw,mode = <2>;
+				reg = <0x84>;
+				label = "vdd_5p0";
+				gw,voltage-divider-ohms = <22100 10000>;
+			};
+
+			channel@86 {
+				gw,mode = <2>;
+				reg = <0x86>;
+				label = "vdd_3p3";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@88 {
+				gw,mode = <2>;
+				reg = <0x88>;
+				label = "vdd_2p5";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@8c {
+				gw,mode = <2>;
+				reg = <0x8c>;
+				label = "vdd_3p0";
+			};
+
+			channel@8e {
+				gw,mode = <2>;
+				reg = <0x8e>;
+				label = "vdd_arm";
+			};
+
+			channel@90 {
+				gw,mode = <2>;
+				reg = <0x90>;
+				label = "vdd_soc";
+			};
+
+			channel@92 {
+				gw,mode = <2>;
+				reg = <0x92>;
+				label = "vdd_1p5";
+			};
+
+			channel@98 {
+				gw,mode = <2>;
+				reg = <0x98>;
+				label = "vdd_1p8";
+			};
+
+			channel@9a {
+				gw,mode = <2>;
+				reg = <0x9a>;
+				label = "vdd_1p0";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@9c {
+				gw,mode = <2>;
+				reg = <0x9c>;
+				label = "vdd_an1";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@a2 {
+				gw,mode = <2>;
+				reg = <0xa2>;
+				label = "vdd_gsc";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	accel@19 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accel>;
+		compatible = "st,lis2de12";
+		reg = <0x19>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <13 0>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
+/* off-board RS232 */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* serial console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* cc1352 */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* Sterling-LWB Bluetooth */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>,<&pinctrl_bten>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		shutdown-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* GPS */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_5p0v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+/* Sterling-LWB SDIO WiFi */
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_wl>;
+	non-removable;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl_accel: accelmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b1
+		>;
+	};
+
+	pinctrl_bten: btengrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b1
+		>;
+	};
+
+	pinctrl_ecspi3: escpi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06  0x1b0b0
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07  0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15  0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x0001b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x1b0b0
+		>;
+	};
+
+	pinctrl_pps: ppsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16	0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_wl: regwlgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D31__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x4001b0b1 /* DIO20 */
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05	0x4001b0b1 /* DIO14 */
+			MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06	0x4001b0b1 /* DIO15 */
+			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08	0x1b0b1 /* TMS */
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09	0x1b0b1 /* TCK */
+			MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10	0x1b0b1 /* TDO */
+			MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11	0x1b0b1 /* TDI */
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x4001b0b1 /* RST# */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x13059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x17059 /* CD */
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x17059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x170b9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x170b9 /* CD */
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x170f9 /* CD */
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x170f9
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5912.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5912.dtsi
new file mode 100644
index 000000000000..49ea25c71967
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5912.dtsi
@@ -0,0 +1,603 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	/* these are used by bootloader for disabling nodes */
+	aliases {
+		led0 = &led0;
+		led1 = &led1;
+		led2 = &led2;
+		nand = &gpmi;
+		usb0 = &usbh1;
+		usb1 = &usbotg;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led0: led-user1 {
+			label = "user1";
+			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led1: led-user2 {
+			label = "user2";
+			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+			default-state = "off";
+		};
+
+		led2: led-user3 {
+			label = "user3";
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
+			default-state = "off";
+		};
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	pps {
+		compatible = "pps-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pps>;
+		gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_vbus: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				gw,mode = <0>;
+				reg = <0x00>;
+				label = "temp";
+			};
+
+			channel@2 {
+				gw,mode = <1>;
+				reg = <0x02>;
+				label = "vdd_vin";
+			};
+
+			channel@5 {
+				gw,mode = <1>;
+				reg = <0x05>;
+				label = "vdd_3p3";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@b {
+				gw,mode = <1>;
+				reg = <0x0b>;
+				label = "vdd_5p0";
+			};
+
+			channel@e {
+				gw,mode = <1>;
+				reg = <0xe>;
+				label = "vdd_arm";
+			};
+
+			channel@11 {
+				gw,mode = <1>;
+				reg = <0x11>;
+				label = "vdd_soc";
+			};
+
+			channel@14 {
+				gw,mode = <1>;
+				reg = <0x14>;
+				label = "vdd_3p0";
+			};
+
+			channel@17 {
+				gw,mode = <1>;
+				reg = <0x17>;
+				label = "vdd_1p5";
+			};
+
+			channel@1d {
+				gw,mode = <1>;
+				reg = <0x1d>;
+				label = "vdd_1p8";
+			};
+
+			channel@20 {
+				gw,mode = <1>;
+				reg = <0x20>;
+				label = "vdd_1p0";
+			};
+
+			channel@23 {
+				gw,mode = <1>;
+				reg = <0x23>;
+				label = "vdd_2p5";
+			};
+		};
+
+		fan-controller@a {
+			compatible = "gw,gsc-fan";
+			reg = <0x0a>;
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	accel@19 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accel>;
+		compatible = "st,lis2de12";
+		reg = <0x19>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <13 0>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>; /* MX6_DIO0 */
+	status = "disabled";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	rts-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_vbus>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	no-1-8-v; /* firmware will remove if board revision supports */
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_accel: accelmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: escpi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26	0x100b1
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06		0x1b0b0
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x0001b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x1b0b0
+		>;
+	};
+
+	pinctrl_pps: ppsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x4001b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11		0x4001b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x13059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x17059 /* CD */
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x17059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x170b9 /* CD */
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x170f9 /* CD */
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x170f9
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__WDOG2_B		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5913.dtsi
new file mode 100644
index 000000000000..82f47c295b08
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5913.dtsi
@@ -0,0 +1,498 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	/* these are used by bootloader for disabling nodes */
+	aliases {
+		led0 = &led0;
+		led1 = &led1;
+		nand = &gpmi;
+		usb0 = &usbh1;
+		usb1 = &usbotg;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pb {
+			label = "user_pb";
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key-erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led0: led-user1 {
+			label = "user1";
+			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led1: led-user2 {
+			label = "user2";
+			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+			default-state = "off";
+		};
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	pps {
+		compatible = "pps-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pps>;
+		gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "5P0V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@6 {
+				gw,mode = <0>;
+				reg = <0x06>;
+				label = "temp";
+			};
+
+			channel@8 {
+				gw,mode = <3>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@82 {
+				gw,mode = <2>;
+				reg = <0x82>;
+				label = "vdd_vin";
+				gw,voltage-divider-ohms = <22100 1000>;
+				gw,voltage-offset-microvolt = <800000>;
+			};
+
+			channel@84 {
+				gw,mode = <2>;
+				reg = <0x84>;
+				label = "vdd_5p0";
+				gw,voltage-divider-ohms = <22100 10000>;
+			};
+
+			channel@86 {
+				gw,mode = <2>;
+				reg = <0x86>;
+				label = "vdd_3p3";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@88 {
+				gw,mode = <2>;
+				reg = <0x88>;
+				label = "vdd_2p5";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@8c {
+				gw,mode = <2>;
+				reg = <0x8c>;
+				label = "vdd_arm";
+			};
+
+			channel@8e {
+				gw,mode = <2>;
+				reg = <0x8e>;
+				label = "vdd_soc";
+			};
+
+			channel@90 {
+				gw,mode = <2>;
+				reg = <0x90>;
+				label = "vdd_1p5";
+			};
+
+			channel@92 {
+				gw,mode = <2>;
+				reg = <0x92>;
+				label = "vdd_1p0";
+			};
+
+			channel@98 {
+				gw,mode = <2>;
+				reg = <0x98>;
+				label = "vdd_3p0";
+			};
+
+			channel@9a {
+				gw,mode = <2>;
+				reg = <0x9a>;
+				label = "vdd_an1";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@a2 {
+				gw,mode = <2>;
+				reg = <0xa2>;
+				label = "vdd_gsc";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+		};
+	};
+
+	gsc_gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+	status = "disabled";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06		0x1b0b0
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x0001b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
+		>;
+	};
+
+	pinctrl_pps: ppsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard.dtsi
index 2ffb21dd89f2..bfade7149080 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard.dtsi
@@ -147,7 +147,7 @@
 &audmux {
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -159,7 +159,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard2-emmc.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2-emmc.dtsi
index f400405381a7..f400405381a7 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard2-emmc.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2-emmc.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2.dtsi
index e4231331f04e..0883ef99cded 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2.dtsi
@@ -179,7 +179,7 @@
 &audmux {
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -191,7 +191,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -203,7 +203,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hummingboard2_ecspi2>;
-	cs-gpios = <&gpio2 26 0>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-icore-1.5.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-1.5.dtsi
index d91d46b5898f..0fd7f2e24d9c 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-1.5.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-1.5.dtsi
@@ -25,10 +25,8 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
 	clocks = <&clks IMX6QDL_CLK_ENET>,
 		 <&clks IMX6QDL_CLK_ENET>,
 		 <&clks IMX6QDL_CLK_ENET_REF>;
-	phy-mode = "rmii";
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-rqs.dtsi
index a4217f564a53..d339957cc097 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-rqs.dtsi
@@ -118,7 +118,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	audmux_ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -130,7 +130,7 @@
 		>;
 	};
 
-	audmux_aud4 {
+	mux-aud4 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -262,7 +262,7 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	vmcc-supply = <&reg_sd3_vmmc>;
+	vmmc-supply = <&reg_sd3_vmmc>;
 	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	no-1-8-v;
@@ -274,7 +274,7 @@
 	pinctrl-0 = <&pinctrl_usdhc4>;
 	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
-	vmcc-supply = <&reg_sd4_vmmc>;
+	vmmc-supply = <&reg_sd4_vmmc>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
index 7814f1ef0804..efe11524b885 100644
--- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
@@ -109,7 +109,7 @@
 	status = "okay";
 
 
-	audmux_ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -121,7 +121,7 @@
 		>;
 	};
 
-	audmux_aud4 {
+	mux-aud4 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -150,10 +150,23 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
 	clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
 	phy-mode = "rmii";
+	phy-handle = <&eth_phy>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <4000>;
+			reset-deassert-us = <4000>;
+		};
+	};
 };
 
 &gpmi {
@@ -232,6 +245,7 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
@@ -384,7 +398,7 @@
 
 	pinctrl_usbotg: usbotggrp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
 		>;
 	};
 
@@ -396,6 +410,7 @@
 			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17070
 			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17070
 			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01  0x1b0b0
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i.dtsi
index 81c7ebb4b3fb..85aeebc9485d 100644
--- a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i.dtsi
@@ -51,16 +51,6 @@
 		vin-supply = <&reg_3p3v_s5>;
 	};
 
-	reg_3p3v_s0: regulator-3p3v-s0 {
-		compatible = "regulator-fixed";
-		regulator-name = "V_3V3_S0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_3p3v_s5>;
-	};
-
 	reg_3p3v_s5: regulator-3p3v-s5 {
 		compatible = "regulator-fixed";
 		regulator-name = "V_3V3_S5";
@@ -137,7 +127,7 @@
 
 	lcd_backlight: lcd-backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		pwm-names = "LCD_BKLT_PWM";
 
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
@@ -167,7 +157,7 @@
 		i2c-gpio,delay-us = <2>; /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabld";
+		status = "disabled";
 	};
 
 	i2c_cam: i2c-gpio-cam {
@@ -179,7 +169,7 @@
 		i2c-gpio,delay-us = <2>; /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabld";
+		status = "disabled";
 	};
 };
 
@@ -245,21 +235,21 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>,
-		   <&gpio2 27 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>,
+		   <&gpio2 27 GPIO_ACTIVE_LOW>;
 };
 
 /* SPI0 */
 &ecspi4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
-	cs-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>,
-		   <&gpio3 29 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>,
+		   <&gpio3 29 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	/* default boot source: workaround #1 for errata ERR006282 */
-	smarc_flash: spi-flash@0 {
-		compatible = "winbond,w25q16dw", "jedec,spi-nor";
+	smarc_flash: flash@0 {
+		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <20000000>;
 	};
@@ -270,7 +260,23 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-handle = <&ethphy>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
 };
 
 &i2c_intern {
@@ -390,7 +396,7 @@
 
 /* I2C_GP */
 &i2c1 {
-	clock-frequency = <100000>;
+	clock-frequency = <375000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 };
@@ -404,7 +410,7 @@
 
 /* I2C_PM */
 &i2c3 {
-	clock-frequency = <100000>;
+	clock-frequency = <375000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
@@ -551,7 +557,7 @@
 
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
 			MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
 		>;
 	};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
new file mode 100644
index 000000000000..4d2abcd44eff
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
@@ -0,0 +1,593 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+		rtc0 = &rtc0;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	beeper: gpio-beeper {
+		compatible = "gpio-beeper";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobeeper>;
+		gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_buttons: gpio-buttons {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobuttons>;
+
+		button-1 {
+			label = "s6";
+			linux,code = <KEY_F6>;
+			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-2 {
+			label = "s7";
+			linux,code = <KEY_F7>;
+			gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-3 {
+			label = "s8";
+			linux,code = <KEY_F8>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_mba6_3p3v: regulator-mba6-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6-3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_regpcie>;
+		regulator-name = "supply-pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* PCIE.PWR_EN */
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		vin-supply = <&reg_mba6_3p3v>;
+	};
+
+	reg_vcc3v3_audio: regulator-vcc3v3-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3-audio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_mba6_3p3v>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_audmux>;
+		model = "imx-audio-tlv320aic32x4";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&tlv320aic32x4>;
+		audio-asrc = <&asrc>;
+		audio-routing =
+			"IN3_L", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"IN1_L", "Line In Jack",
+			"IN1_R", "Line In Jack",
+			"Line Out Jack", "LOL",
+			"Line Out Jack", "LOR";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	status = "okay";
+
+	mux-ssi0 {
+		fsl,audmux-port = <MX31_AUDMUX_PORT1_SSI0>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_SYN |
+				IMX_AUDMUX_V2_PTCR_TFSDIR |
+				IMX_AUDMUX_V2_PTCR_TFSEL(MX31_AUDMUX_PORT3_SSI_PINS_3) |
+				IMX_AUDMUX_V2_PTCR_TCLKDIR |
+				IMX_AUDMUX_V2_PTCR_TCSEL(MX31_AUDMUX_PORT3_SSI_PINS_3))
+			IMX_AUDMUX_V2_PDCR_RXDSEL(MX31_AUDMUX_PORT3_SSI_PINS_3)
+		>;
+	};
+
+	mux-aud3 {
+		fsl,audmux-port = <MX31_AUDMUX_PORT3_SSI_PINS_3>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN
+			IMX_AUDMUX_V2_PDCR_RXDSEL(MX31_AUDMUX_PORT1_SSI0)
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_mba6>;
+	cs-gpios = <&gpio3 19 0>, <&gpio3 24 0>;
+};
+
+&fec {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy>;
+	mac-address = [00 00 00 00 00 00];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@3 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <3>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <100000>;
+			micrel,force-master;
+			max-speed = <1000>;
+		};
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "mclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_codec>;
+		ldoin-supply = <&reg_vcc3v3_audio>;
+		iov-supply = <&reg_mba6_3p3v>;
+	};
+};
+
+/* DDC */
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_recovery>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 7 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@1 {
+		compatible = "usb424,2517";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet@1 {
+			compatible = "usb424,9e00";
+			reg = <1>;
+			nvmem-cells = <&mba_mac_address>;
+			nvmem-cell-names = "mac-address";
+		};
+	};
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	power-active-high;
+	over-current-active-low;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+/* SD card slot */
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_mba6_3p3v>;
+	bus-width = <4>;
+	no-1-8-v;
+	no-mmc;
+	no-sdio;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	/* does not work on unmodified starter kit */
+	/* fsl,ext-reset-output; */
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0xb099
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0xb099
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0xb099
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0xb099
+		>;
+	};
+
+	pinctrl_codec: codecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0xb0 /* CLK */
+		>;
+	};
+
+	pinctrl_ecspi1_mba6: ecspimba6grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24 0xb099 /* eCSPI1 SS2 */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* FEC phy IRQ */
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28     0x00011008
+			/* FEC phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25   0x1b099
+			/* DSE = 100, 100k up, SPEED = MED */
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0xb0a0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC         0xb0a0
+			/* DSE = 111, pull 100k up */
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0xb038
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0xb038
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0xb038
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0xb038
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0xb038
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0xb038
+			/* DSE = 111, pull external */
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x0038
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x0038
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x0038
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x0038
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x0038
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x0038
+			/* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0f0
+		>;
+	};
+
+	pinctrl_gpiobeeper: gpiobeepergrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0xb099
+		>;
+	};
+
+	pinctrl_gpiobuttons: gpiobuttongrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0001b099
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x0001b099
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0001b099
+		>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0xb099 /* LED V15 */
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb099 /* LED V16 */
+		>;
+	};
+
+	pinctrl_hdmi: hdmigrp {
+		/* NOTE: DDC is done via I2C2, so DON'T
+		 * configure DDC pins for HDMI!
+		 */
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0001b099
+
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b099
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b099
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b099
+
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x0001b099
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x0001b099
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x0001b099
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x0001b099
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x0001b099
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x0001b099
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x0001b099
+
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x0001b099
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x0001b099
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x0001b099
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0001b099
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x0001b099
+
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b099
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b099
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x0001b099
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x0001b099
+
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x0001b099
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x0001b099
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x0001b099
+
+			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0001b099
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x0001b099
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
+		>;
+	};
+
+	pinctrl_i2c2_recovery: i2c2recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b899
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b899
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			/* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x001b0f0 /* #PCIE.WAKE */
+			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x001b0f0 /* #PCIE.RST */
+			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x001b0f0 /* #PCIE.DIS */
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
+			MX6QDL_PAD_GPIO_9__PWM1_OUT 0x00003050
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x00003050
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
+			MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x00003050
+		>;
+	};
+
+	pinctrl_regpcie: regpciegrp {
+		fsl,pins = <
+			/* HYS = 1, DSE = 110, PUE+PKE, SPEED = HIGH (11)*/
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x00130f0 /* PCIE.PWR_EN */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b099
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b099
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CLK__UART3_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD4_CMD__UART3_TX_DATA 0x1b0b1
+			MX6QDL_PAD_EIM_D30__UART3_CTS_B   0x1b0b1
+			MX6QDL_PAD_EIM_D31__UART3_RTS_B   0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			/* CLK: 47k Pup SPD_LOW DSE 40Ohm SRE_FAST HYS */
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x00017071
+			/* SD2: 47k Pup SPD_LOW DSE 80Ohm SRE_FAST HYS */
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x00017059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017059
+
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x0001b099 /* usdhc2 CD */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02  0x0001b099 /* usdhc2 WP */
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC  0x0001b0b0
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID   0x00017059
+			MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x0001b099
+		>;
+	};
+
+	pinctrl_wdog1: wdog1grp {
+		fsl,pins = <
+			 /* Watchdog out */
+			MX6QDL_PAD_SD1_DAT2__WDOG1_B 0x0000b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6a.dtsi
new file mode 100644
index 000000000000..238f3af42822
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6a.dtsi
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>, <&pinctrl_enet_fix>;
+};
+
+&i2c1 {
+	lm75: temperature-sensor@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+		vs-supply = <&reg_mba6_3p3v>;
+	};
+
+	m24c64_57: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		vcc-supply = <&reg_mba6_3p3v>;
+
+		mba_mac_address: mac-address@20 {
+			reg = <0x20 0x6>;
+		};
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6b.dtsi
new file mode 100644
index 000000000000..a587bc88f76f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6b.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_recovery>;
+	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	lm75: temperature-sensor@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+		vs-supply = <&reg_mba6_3p3v>;
+	};
+
+	m24c64_57: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		vcc-supply = <&reg_mba6_3p3v>;
+
+		mba_mac_address: mac-address@20 {
+			reg = <0x20 0x6>;
+		};
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
index 2418cf8f2317..f2542d725ce7 100644
--- a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
@@ -15,51 +15,41 @@
 		reg = <0x10000000 0x20000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
 
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_wlan_vmmc: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_wlan_vmmc>;
-			regulator-name = "reg_wlan_vmmc";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <70000>;
-			enable-active-high;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
 	};
 
 	gpio-keys {
@@ -85,31 +75,31 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds>;
 
-		j14-pin1 {
+		led-j14-pin1 {
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
 			retain-state-suspended;
 			default-state = "off";
 		};
 
-		j14-pin3 {
+		led-j14-pin3 {
 			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 			retain-state-suspended;
 			default-state = "off";
 		};
 
-		j14-pins8-9 {
+		led-j14-pins8-9 {
 			gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 			retain-state-suspended;
 			default-state = "off";
 		};
 
-		j46-pin2 {
+		led-j46-pin2 {
 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
 			retain-state-suspended;
 			default-state = "off";
 		};
 
-		j46-pin3 {
+		led-j46-pin3 {
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			retain-state-suspended;
 			default-state = "off";
@@ -179,7 +169,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -190,23 +180,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	txen-skew-ps = <0>;
-	txc-skew-ps = <3000>;
-	rxdv-skew-ps = <0>;
-	rxc-skew-ps = <3000>;
-	rxd0-skew-ps = <0>;
-	rxd1-skew-ps = <0>;
-	rxd2-skew-ps = <0>;
-	rxd3-skew-ps = <0>;
-	txd0-skew-ps = <0>;
-	txd1-skew-ps = <0>;
-	txd2-skew-ps = <0>;
-	txd3-skew-ps = <0>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
 };
 
 &hdmi {
@@ -225,6 +226,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -497,6 +499,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -509,6 +512,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
index c3415aa348a2..32a110a35b02 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
@@ -15,83 +15,70 @@
 		reg = <0x10000000 0xF0000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
 
-		reg_1p8v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "1P8V";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
 
-		reg_2p5v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb_otg_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb_h1_vbus: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_wlan_vmmc: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_wlan_vmmc>;
-			regulator-name = "reg_wlan_vmmc";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <70000>;
-			enable-active-high;
-		};
-
-		reg_can_xcvr: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "CAN XCVR";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_can_xcvr>;
-			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
-		};
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
 	};
 
 	gpio-keys {
@@ -181,13 +168,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		speaker-enable {
+		led-speaker-enable {
 			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 			retain-state-suspended;
 			default-state = "off";
 		};
 
-		ttymxc4-rs232 {
+		led-ttymxc4-rs232 {
 			gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
 			retain-state-suspended;
 			default-state = "on";
@@ -316,12 +303,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -332,23 +319,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	txen-skew-ps = <0>;
-	txc-skew-ps = <3000>;
-	rxdv-skew-ps = <0>;
-	rxc-skew-ps = <3000>;
-	rxd0-skew-ps = <0>;
-	rxd1-skew-ps = <0>;
-	rxd2-skew-ps = <0>;
-	rxd3-skew-ps = <0>;
-	txd0-skew-ps = <0>;
-	txd1-skew-ps = <0>;
-	txd2-skew-ps = <0>;
-	txd3-skew-ps = <0>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
 };
 
 &hdmi {
@@ -367,6 +365,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -736,12 +735,14 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
@@ -754,6 +755,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
index ed53f07c6b7b..414196b75991 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
@@ -247,12 +247,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -263,6 +263,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -285,6 +286,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -639,6 +641,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -651,6 +654,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
index 8b0e432099b5..f278b14911ce 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
@@ -17,74 +17,62 @@
 		reg = <0x10000000 0x40000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
 
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-
-		reg_can_xcvr: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "CAN XCVR";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_can_xcvr>;
-			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
-		};
-
-		reg_wlan_vmmc: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_wlan_vmmc>;
-			regulator-name = "reg_wlan_vmmc";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <70000>;
-			enable-active-high;
-		};
-
-		reg_usb_h1_vbus: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	gpio-keys {
@@ -232,12 +220,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 0>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -265,23 +253,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	txen-skew-ps = <0>;
-	txc-skew-ps = <3000>;
-	rxdv-skew-ps = <0>;
-	rxc-skew-ps = <3000>;
-	rxd0-skew-ps = <0>;
-	rxd1-skew-ps = <0>;
-	rxd2-skew-ps = <0>;
-	rxd3-skew-ps = <0>;
-	txd0-skew-ps = <0>;
-	txd1-skew-ps = <0>;
-	txd2-skew-ps = <0>;
-	txd3-skew-ps = <0>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
 };
 
 &hdmi {
@@ -298,6 +297,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -596,6 +596,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -608,6 +609,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-av-02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-av-02.dtsi
new file mode 100644
index 000000000000..0020dbb1722c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-av-02.dtsi
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/ {
+	display: display0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_disp0>;
+		interface-pix-fmt = "rgb24";
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&peb_panel_lcd_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "edt,etm0700g0edh6";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_disp0_pwr>;
+		power-supply = <&reg_display>;
+		enable-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		backlight = <&backlight>;
+		status = "disabled";
+
+		port {
+			peb_panel_lcd_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+
+	reg_display: regulator-peb-display {
+		compatible = "regulator-fixed";
+		regulator-name = "peb-display";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&i2c1 {
+	edt_ft5x06: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_edt_ft5x06>;
+		reg = <0x38>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <2 IRQ_TYPE_NONE>;
+		status = "disabled";
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_disp0: disp0grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x1b080
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_disp0_pwr: disp0pwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_edt_ft5x06: edtft5x06grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02			0xb0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-eval-01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-eval-01.dtsi
new file mode 100644
index 000000000000..037b60197598
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-eval-01.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+
+		sleep {
+			label = "Sleep Button";
+			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_SLEEP>;
+		};
+	};
+
+	user_leds: user-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_user_leds>;
+		status = "disabled";
+
+		user-led1 {
+			gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+
+		user-led2 {
+			gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+
+		user-led3 {
+			gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT6__GPIO6_IO18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28	0x1b0b0
+		>;
+	};
+
+	pinctrl_user_leds: userledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1b0b0
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-wlbt-05.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
new file mode 100644
index 000000000000..84f884d6e55b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	reg_wl_en: regulator-wl-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wl>;
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		status = "disabled";
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_bt>;
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&usdhc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_wl>;
+	vmmc-supply = <&reg_wl_en>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	status = "disabled";
+
+	brmcf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl_uart3_bt: uart3grp-bt {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_EB3__UART3_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0xb0b1	/* BT ENABLE */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0xb0b1	/* DEV WAKEUP */
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0xb0b1  /* HOST WAKEUP */
+		>;
+	};
+
+	pinctrl_usdhc3_wl: usdhc3grp-wl {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_wl: wlgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02      0xb0b1	/* WLAN ENABLE */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
index 9ebd438dce7d..1ca4d219609f 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
@@ -25,17 +25,17 @@
 		pinctrl-0 = <&pinctrl_gpioleds>;
 		status = "disabled";
 
-		red {
+		led-red {
 			label = "phyboard-mira:red";
 			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "phyboard-mira:green";
 			gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "phyboard-mira:blue";
 			gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
@@ -145,8 +145,11 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <400000>;
 	status = "disabled";
 
@@ -179,14 +182,17 @@
 		pinctrl-0 = <&pinctrl_rtc_int>;
 		reg = <0x68>;
 		interrupt-parent = <&gpio7>;
-		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		status = "disabled";
 	};
 };
 
 &i2c2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <100000>;
 	status = "disabled";
 };
@@ -218,6 +224,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -255,6 +262,7 @@
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
 	no-1-8-v;
+	disable-wp;
 	status = "disabled";
 };
 
@@ -298,6 +306,20 @@
 		>;
 	};
 
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x4001b8b1
+		>;
+	};
+
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
@@ -305,10 +327,10 @@
 		>;
 	};
 
-	pinctrl_i2c1: i2c1grp {
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x4001b8b1
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x4001b8b1
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pbab01.dtsi
index d434868e870a..e40041871b28 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pbab01.dtsi
@@ -10,22 +10,18 @@
 		stdout-path = &uart4;
 	};
 
-	regulators {
-		sound_1v8: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "i2s-audio-1v8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
+	sound_1v8: regulator-sound-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "i2s-audio-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
 
-		sound_3v3: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "i2s-audio-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	sound_3v3: regulator-sound-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "i2s-audio-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 	};
 
 	tlv320_mclk: oscillator {
@@ -75,10 +71,11 @@
 &audmux {
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
-			(IMX_AUDMUX_V2_PTCR_TFSDIR |
+			(IMX_AUDMUX_V2_PTCR_SYN |
+			IMX_AUDMUX_V2_PTCR_TFSDIR |
 			IMX_AUDMUX_V2_PTCR_TFSEL(4) |
 			IMX_AUDMUX_V2_PTCR_TCLKDIR |
 			IMX_AUDMUX_V2_PTCR_TCSEL(4))
@@ -86,10 +83,10 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
-			0x00000000
+			IMX_AUDMUX_V2_PTCR_SYN
 			IMX_AUDMUX_V2_PDCR_RXDSEL(1)
 		>;
 	};
@@ -164,6 +161,7 @@
 
 &usbotg {
 	status = "okay";
+	dr_mode = "peripheral";
 };
 
 &usdhc2 {
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pfla02.dtsi
index bc43c75f1745..113974520d54 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pfla02.dtsi
@@ -14,41 +14,37 @@
 		reg = <0x10000000 0x80000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb_otg_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio4 15 0>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 15 0>;
+		enable-active-high;
+	};
 
-		reg_usb_h1_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 0 0>;
-			enable-active-high;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 0>;
+		enable-active-high;
 	};
 
 	gpio_leds: leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
 		compatible = "gpio-leds";
 
-		green {
+		led_green: led-green {
 			label = "phyflex:green";
 			gpios = <&gpio1 30 0>;
 		};
 
-		red {
+		led_red: led-red {
 			label = "phyflex:red";
 			gpios = <&gpio2 31 0>;
 		};
@@ -71,7 +67,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
-	cs-gpios = <&gpio4 24 0>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 
 	som_flash: flash@0 {
 		compatible = "m25p80", "jedec,spi-nor";
@@ -116,11 +112,14 @@
 	status = "okay";
 
 	som_eeprom: eeprom@50 {
-		compatible = "atmel,24c32";
+		compatible = "catalyst,24c32", "atmel,24c32";
+		pagesize = <32>;
 		reg = <0x50>;
 	};
 
 	pmic@58 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
 		compatible = "dlg,da9063";
 		reg = <0x58>;
 		interrupt-parent = <&gpio2>;
@@ -198,6 +197,19 @@
 				regulator-always-on;
 			};
 		};
+
+		da9063_rtc: rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		da9063_wdog: watchdog {
+			compatible = "dlg,da9063-watchdog";
+		};
+
+		onkey {
+			compatible = "dlg,da9063-onkey";
+			status = "disabled";
+		};
 	};
 };
 
@@ -214,25 +226,13 @@
 };
 
 &iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
 	imx6q-phytec-pfla02 {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000
-				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* SPI NOR chipselect */
-				MX6QDL_PAD_SD4_DAT1__GPIO2_IO09  0x80000000 /* PMIC interrupt */
-				MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* Green LED */
-				MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x80000000 /* Red LED */
-			>;
-		};
-
 		pinctrl_ecspi3: ecspi3grp {
 			fsl,pins = <
 				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
 				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
 				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x80000000 /* CS0 */
 			>;
 		};
 
@@ -254,6 +254,7 @@
 				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
 				MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x80000000 /* Reset GPIO */
 			>;
 		};
 
@@ -307,16 +308,27 @@
 			>;
 		};
 
+		pinctrl_leds: ledsgrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000 /* Green LED */
+				MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x80000000 /* Red LED */
+			>;
+		};
+
 		pinctrl_pcie: pciegrp {
 			fsl,pins = <MX6QDL_PAD_DI0_PIN15__GPIO4_IO17  0x80000000>;
 		};
 
+		pinctrl_pmic: pmicgrp {
+			fsl,pins = <MX6QDL_PAD_SD4_DAT1__GPIO2_IO09	0x80000000>; /* PMIC interrupt */
+		};
+
 		pinctrl_uart3: uart3grp {
 			fsl,pins = <
 				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
 				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D30__UART3_RTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_CTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
 			>;
 		};
 
@@ -327,9 +339,9 @@
 			>;
 		};
 
-		pinctrl_usbh1: usbh1grp {
+		pinctrl_usbh1_vbus: usbh1vbusgrp {
 			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__USB_H1_PWR		0x80000000
+				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
 			>;
 		};
 
@@ -403,6 +415,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
 	status = "disabled";
 };
 
@@ -414,8 +427,6 @@
 
 &usbh1 {
 	vbus-supply = <&reg_usb_h1_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1>;
 	status = "disabled";
 };
 
@@ -432,6 +443,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vdd_sd1_reg>;
 	status = "disabled";
 };
 
@@ -441,5 +453,14 @@
 		     &pinctrl_usdhc3_cdwp>;
 	cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vdd_sd0_reg>;
+	status = "disabled";
+};
+
+&wdog1 {
+	/*
+	 * Rely on PMIC reboot handler. Internal i.MX6 watchdog, that is also
+	 * used for reboot, does not reset all external PMIC voltages on reset.
+	 */
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
index 6486df3e2942..86b4269e0e01 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
@@ -5,6 +5,7 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/dlg,da9063-regulator.h>
 
 / {
 	aliases {
@@ -77,17 +78,21 @@
 };
 
 &i2c3 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <400000>;
 	status = "okay";
 
 	eeprom@50 {
-		compatible = "atmel,24c32";
+		compatible = "st,24c32", "atmel,24c32";
+		pagesize = <32>;
 		reg = <0x50>;
 	};
 
-	pmic@58 {
+	pmic: pmic@58 {
 		compatible = "dlg,da9062";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;
@@ -95,27 +100,46 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
+		gpio-controller;
+		#gpio-cells = <2>;
 
 		da9062_rtc: rtc {
 			compatible = "dlg,da9062-rtc";
 		};
 
+		da9062_onkey: onkey {
+			compatible = "dlg,da9062-onkey";
+		};
+
 		watchdog {
 			compatible = "dlg,da9062-watchdog";
+			dlg,use-sw-pm;
+		};
+
+		thermal {
+			compatible = "dlg,da9062-thermal";
+			status = "disabled";
+		};
+
+		gpio {
+			compatible = "dlg,da9062-gpio";
+			status = "disabled";
 		};
 
 		regulators {
 			vdd_arm: buck1 {
 				regulator-name = "vdd_arm";
-				regulator-min-microvolt = <730000>;
+				regulator-min-microvolt = <925000>;
 				regulator-max-microvolt = <1380000>;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
 				regulator-always-on;
 			};
 
 			vdd_soc: buck2 {
 				regulator-name = "vdd_soc";
-				regulator-min-microvolt = <730000>;
+				regulator-min-microvolt = <1150000>;
 				regulator-max-microvolt = <1380000>;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
 				regulator-always-on;
 			};
 
@@ -123,6 +147,7 @@
 				regulator-name = "vdd_ddr3";
 				regulator-min-microvolt = <1500000>;
 				regulator-max-microvolt = <1500000>;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
 				regulator-always-on;
 			};
 
@@ -130,6 +155,7 @@
 				regulator-name = "vdd_eth";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1200000>;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
 				regulator-always-on;
 			};
 
@@ -183,7 +209,6 @@
 	pinctrl-0 = <&pinctrl_usdhc4>;
 	bus-width = <8>;
 	non-removable;
-	vmmc-supply = <&vdd_emmc_1p8>;
 	status = "disabled";
 };
 
@@ -247,6 +272,13 @@
 		>;
 	};
 
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06	0x4001b8b1
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x4001b8b1
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
@@ -277,3 +309,11 @@
 		>;
 	};
 };
+
+&wdog1 {
+	/*
+	 * Rely on PMIC reboot handler. Internal i.MX6 watchdog, that is also
+	 * used for reboot, does not reset all external PMIC voltages on reset.
+	 */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-dwarf.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-dwarf.dtsi
new file mode 100644
index 000000000000..3a968782e854
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-dwarf.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+//
+// Copyright 2017 NXP
+
+#include "imx6qdl-pico.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led {
+			label = "gpio-led";
+			gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+};
+
+&i2c1 {
+	mpl3115@60 {
+		compatible = "fsl,mpl3115";
+		reg = <0x60>;
+	};
+};
+
+&i2c2 {
+	io-expander@25 {
+		compatible = "nxp,pca9554";
+		reg = <0x25>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+};
+
+&iomuxc {
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-hobbit.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-hobbit.dtsi
new file mode 100644
index 000000000000..144c4727fbc7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-hobbit.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+//
+// Copyright 2017 NXP
+
+#include "imx6qdl-pico.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led {
+			label = "gpio-led";
+			gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+};
+
+&i2c2 {
+	status = "okay";
+
+	adc081c: adc@50 {
+		compatible = "ti,adc081c";
+		reg = <0x50>;
+		vref-supply = <&reg_3p3v>;
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-nymph.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-nymph.dtsi
new file mode 100644
index 000000000000..3d56a4216448
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-nymph.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+
+#include "imx6qdl-pico.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led {
+			label = "gpio-led";
+			gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+};
+
+&i2c1 {
+	adc@52 {
+		compatible = "ti,adc081c";
+		reg = <0x52>;
+		vref-supply = <&reg_2p5v>;
+	};
+};
+
+&i2c2 {
+	io-expander@25 {
+		compatible = "nxp,pca9554";
+		reg = <0x25>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+};
+
+&i2c3 {
+	rtc@68 {
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-pi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-pi.dtsi
new file mode 100644
index 000000000000..b823dce62e63
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-pi.dtsi
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+//
+// Copyright 2017 NXP
+
+#include "imx6qdl-pico.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led {
+			label = "gpio-led";
+			gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+};
+
+&hdmi {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico.dtsi
new file mode 100644
index 000000000000..c39a9ebdaba1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico.dtsi
@@ -0,0 +1,627 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright 2018 Technexion Ltd.
+//
+// Author: Wig Cheng <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_1p5v: regulator-1p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reg_2p8v: regulator-2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
+	};
+
+	codec_osc: clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx6-pico-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 50000 0>;
+		brightness-levels = <0 36 72 108 144 180 216 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_lcd>;
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "vxt,vl050-8048nt-c01";
+		backlight = <&backlight>;
+		power-supply = <&reg_lcd_3v3>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+	phy-handle = <&phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	sgtl5000: audio-codec@a {
+		#sound-dai-cells = <0>;
+		reg = <0x0a>;
+		compatible = "fsl,sgtl5000";
+		clocks = <&codec_osc>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_1p8v>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio5 27 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		wakeup-source;
+	};
+
+	camera@3c {
+		compatible = "ovti,ov5645";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5645>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-frequency = <24000000>;
+		vdddo-supply = <&reg_1p8v>;
+		vdda-supply = <&reg_2p8v>;
+		vddd-supply = <&reg_1p5v>;
+		enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5645_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&mipi_csi {
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5645_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie_reset>;
+	reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {  /* Bluetooth module */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	cd-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc2 {  /* Wifi/BT  */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x4001b0b5 /* PICO_P24 */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x4001b0b5 /* PICO_P26 */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x4001b0b5 /* PICO_P28 */
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x4001b0b5 /* PICO_P30 */
+			MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27	0x4001b0b5 /* PICO_P32 */
+			MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x4001b0b5 /* PICO_P34 */
+			MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30	0x4001b0b5 /* PICO_P42 */
+			MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31	0x4001b0b5 /* PICO_P44 */
+			MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01	0x4001b0b5 /* PICO_P48 */
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x000f0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO		0x1b0b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI		0x1b0b1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK		0x1b0b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x000f0b0
+			MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x000f0b0
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1f0b1
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX	0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_ov5645: ov5645grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x0b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x0b0b0
+			MX6QDL_PAD_GPIO_3__CCM_CLKO2		0x000b0
+		>;
+	};
+
+	pinctrl_pcie_reset: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x130b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__PWM2_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_lcd: reglcdgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11		0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT5__UART2_RTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT6__UART2_CTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotgvbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17071
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x17071
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x17071
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x17071
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x17071
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x17071
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0xb0b1
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-prti6q.dtsi
new file mode 100644
index 000000000000..36f84f4da6b0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-prti6q.dtsi
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_h1_vbus: regulator-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "h1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b008
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b008
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC	0x1b0b0
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-rex.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-rex.dtsi
index de514eb5aa99..eba698d04243 100644
--- a/arch/arm/boot/dts/imx6qdl-rex.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-rex.dtsi
@@ -13,41 +13,32 @@
 		stdout-path = &uart1;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usbh1_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			pinctrl-names = "default";
-			regulator-name = "usbh1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		regulator-name = "usbh1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			pinctrl-names = "default";
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	leds {
@@ -55,7 +46,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		led0: usr {
+		led0: led-usr {
 			label = "usr";
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -120,6 +111,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
index cf628465cd0a..68e97180d33e 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
@@ -21,7 +21,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>;
 		};
@@ -267,12 +267,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 0>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
 	status = "disabled"; /* pin conflict with WEIM NOR */
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -295,9 +295,11 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
+	fsl,magic-packet;
 	status = "okay";
 };
 
@@ -334,7 +336,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -450,8 +452,8 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_egalax_int>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -800,6 +802,7 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
index 8468216dae9b..84c8a9531e18 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
@@ -1,43 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
 /*
  * Copyright 2011 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/clock/imx6qdl-clock.h>
@@ -49,93 +14,84 @@
 		stdout-path = &uart2;
 	};
 
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
+	};
+
 	memory@10000000 {
 		device_type = "memory";
 		reg = <0x10000000 0x40000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
 
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-
-		reg_can_xcvr: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "CAN XCVR";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_can_xcvr>;
-			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
-		};
-
-		reg_1p5v: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "1P5V";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			regulator-always-on;
-		};
-
-		reg_1p8v: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "1P8V";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		reg_2p8v: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "2P8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			regulator-always-on;
-		};
-
-		reg_usb_h1_vbus: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_1p5v: regulator-1p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_2p8v: regulator-2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	mipi_xclk: mipi_xclk {
@@ -308,12 +264,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 0>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -324,20 +280,30 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-	txen-skew-ps = <0>;
-	txc-skew-ps = <3000>;
-	rxdv-skew-ps = <0>;
-	rxc-skew-ps = <3000>;
-	rxd0-skew-ps = <0>;
-	rxd1-skew-ps = <0>;
-	rxd2-skew-ps = <0>;
-	rxd3-skew-ps = <0>;
-	txd0-skew-ps = <0>;
-	txd1-skew-ps = <0>;
-	txd2-skew-ps = <0>;
-	txd3-skew-ps = <0>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
 };
 
 &hdmi {
@@ -354,6 +320,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -687,18 +654,21 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
index 71ca76a5e4a5..4fe58764b929 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
@@ -97,17 +97,24 @@
 		compatible = "fsl,imx6q-sabresd-wm8962",
 			   "fsl,imx-audio-wm8962";
 		model = "wm8962-audio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
 		ssi-controller = <&ssi2>;
 		audio-codec = <&codec>;
+		audio-asrc = <&asrc>;
 		audio-routing =
 			"Headphone Jack", "HPOUTL",
 			"Headphone Jack", "HPOUTR",
 			"Ext Spk", "SPKOUTL",
 			"Ext Spk", "SPKOUTR",
 			"AMIC", "MICBIAS",
-			"IN3R", "AMIC";
+			"IN3R", "AMIC",
+			"DMIC", "MICBIAS",
+			"DMICDAT", "DMIC";
 		mux-int-port = <2>;
 		mux-ext-port = <3>;
+		hp-det-gpio = <&gpio7 8 GPIO_ACTIVE_LOW>;
+		mic-det-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
 	};
 
 	backlight_lvds: backlight-lvds {
@@ -123,7 +130,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		red {
+		led-red {
 			gpios = <&gpio1 2 0>;
 			default-state = "on";
 		};
@@ -185,12 +192,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio4 9 0>;
+	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -203,8 +210,21 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-handle = <&phy>;
+	fsl,magic-packet;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+		};
+	};
 };
 
 &hdmi {
@@ -291,8 +311,8 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c2_egalax_int>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-gpios = <&gpio6 8 GPIO_ACTIVE_LOW>;
 	};
 
 	ov5640: camera@3c {
@@ -318,7 +338,7 @@
 		};
 	};
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -430,8 +450,8 @@
 		compatible = "eeti,egalax_ts";
 		reg = <0x04>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <7 2>;
-		wakeup-gpios = <&gpio6 7 0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
 	};
 
 	magnetometer@e {
@@ -528,6 +548,13 @@
 			>;
 		};
 
+		pinctrl_hp: hpgrp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_RST__GPIO7_IO08          0x1b0b0
+				MX6QDL_PAD_GPIO_9__GPIO1_IO09           0x1b0b0
+			>;
+		};
+
 		pinctrl_i2c1: i2c1grp {
 			fsl,pins = <
 				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
@@ -728,6 +755,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -749,10 +777,6 @@
 	vin-supply = <&vgen5_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen5_reg>;
 };
diff --git a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
index a616e3c400d3..02e6d36e85fa 100644
--- a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
@@ -140,6 +140,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu-revc.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
new file mode 100644
index 000000000000..596b3bb3ddd1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+/ {
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>, <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <65000>;
+		touchscreen-inverted-y;
+		touchscreen-swapped-x-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+};
+
+&ecspi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_touch>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 19 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D28__ECSPI4_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D22__ECSPI4_MISO			0x000b1
+			MX6QDL_PAD_EIM_D21__ECSPI4_SCLK			0x000b1
+			/* *no* external pull up */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x40000058
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			/* external pull up */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x10040
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
new file mode 100644
index 000000000000..2731faede1cb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	aliases {
+		can0 = &can1;
+		can1 = &can2;
+		mdio-gpio0 = &mdio;
+		nand = &gpmi;
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs;
+		usb0 = &usbh1;
+		usb1 = &usbotg;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, /* 24V */
+		              <&adc 1>; /* temperature */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "D1";
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_STATUS;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "D2";
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "D3";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	mdio: mdio {
+		compatible = "microchip,mdio-smi0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mdio>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>,
+			<&gpio1 22 GPIO_ACTIVE_HIGH>;
+
+		switch@0 {
+			compatible = "microchip,ksz8873";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_switch>;
+			interrupt-parent = <&gpio3>;
+			interrupt = <30 IRQ_TYPE_LEVEL_HIGH>;
+			reset-gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+			reg = <0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports@0 {
+					reg = <0>;
+					phy-mode = "internal";
+					label = "lan1";
+				};
+
+				ports@1 {
+					reg = <1>;
+					phy-mode = "internal";
+					label = "lan2";
+				};
+
+				ports@2 {
+					reg = <2>;
+					label = "cpu";
+					ethernet = <&fec>;
+					phy-mode = "rmii";
+
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+			};
+		};
+
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_5v0>;
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_24v0: regulator-24v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "24v0";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+	};
+
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can1_stby>;
+		regulator-name = "can1-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_can2_stby: regulator-can2-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can2_stby>;
+		regulator-name = "can2-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 11 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_tft_vcom: regulator-tft-vcom {
+		compatible = "pwm-regulator";
+		pwms = <&pwm3 0 20000 0>;
+		regulator-name = "tft_vcom";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		regulator-always-on;
+		voltage-table = <3600000 26>;
+	};
+
+	reg_vcc_mmc: regulator-vcc-mmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc>;
+		vin-supply = <&reg_3v3>;
+		regulator-name = "mmc_vcc_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+	};
+
+	reg_vcc_mmc_io: regulator-vcc-mmc-io {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc_io>;
+		vin-supply = <&reg_5v0>;
+		regulator-name = "mmc_io_supply";
+		regulator-type = "voltage";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		states = <1800000 0x1>, <3300000 0x0>;
+		startup-delay-us = <100>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can1_stby>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_can2_stby>;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <54000000>;
+		reg = <0>;
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	adc: adc@0 {
+		compatible = "microchip,mcp3002";
+		reg = <0>;
+		vref-supply = <&reg_3v3>;
+		spi-max-frequency = <1000000>;
+		#io-channel-cells = <1>;
+	};
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_3v3>;
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	i2c_rtc: rtc@51 {
+		compatible = "nxp,pcf85063";
+		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	#pwm-cells = <2>;
+	status = "okay";
+};
+
+&pwm3 {
+	/* used for LCD contrast control */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_5v0>;
+	disable-over-current;
+	status = "okay";
+};
+
+/* no usbh2 */
+&usbphynop1 {
+	status = "disabled";
+};
+
+/* no usbh3 */
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usbotg {
+	vbus-supply = <&reg_5v0>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	cap-power-off-card;
+	full-pwr-cycle;
+	bus-width = <4>;
+	max-frequency = <50000000>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	mmc-ddr-1_8v;
+	vmmc-supply = <&reg_vcc_mmc>;
+	vqmmc-supply = <&reg_vcc_mmc_io>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__FLEXCAN1_TX			0x3008
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX			0x1b000
+		>;
+	};
+
+	pinctrl_can1_stby: can1stbygrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x13008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+		>;
+	};
+
+	pinctrl_can2_stby: can2stbygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0xb1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0xb1
+			/* *no* external pull up */
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24			0x58
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO			0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI			0xb1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK			0xb1
+			/* external pull up */
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26			0x58
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* RMII 50 MHz */
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x100f5
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x100f5
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x100c0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x100c0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x100f5
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x100f5
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05			0x58
+			/* GPIO for "link active" */
+			MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24		0x3038
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE			0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE			0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B		0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B		0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B		0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B			0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B			0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00		0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01		0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02		0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03		0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04		0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05		0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06		0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07		0xb0b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			/* external 10 k pull up */
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x40010878
+			/* external 10 k pull up */
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x40010878
+		>;
+	};
+
+	pinctrl_mdio: mdiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__GPIO1_IO22		0x100b1
+			MX6QDL_PAD_ENET_MDC__GPIO1_IO31			0xb1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__PWM2_OUT			0x58
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT			0x58
+		>;
+	};
+
+	pinctrl_switch: switchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0xb0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			/* SoC internal pull up required */
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17059
+			/* SoC internal pull up required */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01			0x1b040
+			/* SoC internal pull up required */
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00			0x1b040
+		>;
+	};
+
+	pinctrl_vcc_mmc: vccmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08			0x58
+		>;
+	};
+
+	pinctrl_vcc_mmc_io: vccmmciogrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13			0x58
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-revc-lt2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-revc-lt2.dtsi
new file mode 100644
index 000000000000..48c9ce051f47
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-revc-lt2.dtsi
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (C) 2021 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
+
+/ {
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		enable-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
+		pwms = <&pwm2 0 20000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <17>;
+		default-brightness-level = <8>;
+		power-supply = <&reg_24v0>;
+	};
+
+	display {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "logictechno,lttd800480070-l2rt";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23		0x58
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-solidsense.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-solidsense.dtsi
new file mode 100644
index 000000000000..234827e554d0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-solidsense.dtsi
@@ -0,0 +1,160 @@
+/*
+ * Copyright (C) 2021 Russell King <rmk@armlinux.org.uk>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/leds/common.h>
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_solidsense_leds>;
+
+		/* Red/Green LED1 - next to WiFi SMA */
+		led-11 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <0>;
+			gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+		};
+
+		led-12 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <0>;
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Red/Green LED2 - next to GPS SMA */
+		led-21 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-22 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&audio {
+	status = "disabled";
+};
+
+&ecspi2 {
+	status = "disabled";
+};
+
+&i2c3 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog>, <&pinctrl_solidsense_hog>;
+
+	solidsense {
+		pinctrl_solidsense_hog: solidsense-hog {
+			fsl,pins = <
+				/* Nordic RESET_N */
+				MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x400130b1
+				/* Nordic Chip 1 SWDIO - GPIO 125 */
+				MX6QDL_PAD_DISP0_DAT8__GPIO4_IO29 0x400130b1
+				/* Nordic Chip 1 SWDCLK - GPIO 59 */
+				/* already claimed in the HB2 hogs */
+				/* MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x400130b1 */
+				/* Nordic Chip 2 SWDIO - GPIO 81 */
+				MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x400130b1
+				/* Nordic Chip 2 SWCLK - GPIO 82 */
+				MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x400130b1
+			>;
+		};
+
+		pinctrl_solidsense_leds: solidsense-leds {
+			fsl,pins = <
+				/* Red LED 1 - GPIO 58 */
+				MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x400130b1
+				/* Green LED 1 - GPIO 55 */
+				MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x400130b1
+				/* Red LED 2 - GPIO 57 */
+				MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x400130b1
+				/* Green LED 2 - GPIO 56 */
+				MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x400130b1
+			>;
+		};
+
+		pinctrl_solidsense_uart2: solidsense-uart2 {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_solidsense_uart3: solidsense-uart3 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			>;
+		};
+	};
+};
+
+&pwm1 {
+	status = "disabled";
+};
+
+&sgtl5000 {
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_solidsense_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_solidsense_uart3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som-brcm.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-brcm.dtsi
index b55af61dfeca..b55af61dfeca 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som-brcm.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-brcm.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som-emmc.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-emmc.dtsi
index 5f3b8baab20f..5f3b8baab20f 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som-emmc.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-emmc.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som-ti.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-ti.dtsi
index 44a97ba93a95..352ac585ca6b 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som-ti.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-ti.dtsi
@@ -153,6 +153,7 @@
 	bus-width = <4>;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&pwrseq_ti_wifi>;
+	cap-power-off-card;
 	non-removable;
 	vmmc-supply = <&vcc_3v3>;
 	/* vqmmc-supply = <&nvcc_sd1>; - MMC layer doesn't like it! */
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som.dtsi
index 6d7f6b9035bc..ce543e325cd3 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som.dtsi
@@ -54,9 +54,46 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
 	phy-mode = "rgmii-id";
-	phy-reset-duration = <2>;
+
+	/*
+	 * The PHY seems to require a long-enough reset duration to avoid
+	 * some rare issues where the PHY gets stuck in an inconsistent and
+	 * non-functional state at boot-up. 10ms proved to be fine .
+	 */
+	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/*
+		 * The PHY can appear at either address 0 or 4 due to the
+		 * configuration (LED) pin not being pulled sufficiently.
+		 */
+		ethernet-phy@0 {
+			reg = <0>;
+			qca,clk-out-frequency = <125000000>;
+			qca,smarteee-tw-us-1g = <24>;
+		};
+
+		ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+			qca,smarteee-tw-us-1g = <24>;
+		};
+
+		/*
+		 * ADIN1300 (som rev 1.9 or later) is always at address 1. It
+		 * will be enabled automatically by U-Boot if detected.
+		 */
+		ethernet-phy@1 {
+			reg = <1>;
+			adi,phy-output-clock = "125mhz-free-running";
+			status = "disabled";
+		};
+	};
 };
 
 &iomuxc {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6.dtsi
new file mode 100644
index 000000000000..344ea935c7da
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	m25p80: flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		m25p,fast-read;
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			/* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b099
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0xb099
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0xb099
+			 /* eCSPI1 SS1 */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19 0xb099
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
+		>;
+	};
+
+	pinctrl_i2c1_recovery: i2c1recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x4001b899
+			MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3_recovery: i2c3recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b899
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b899
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b099 /* PMIC irq */
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+		>;
+	};
+};
+
+&pmic {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+	interrupt-parent = <&gpio6>;
+	interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+	regulators {
+		reg_vddcore: sw1ab {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1875000>;
+			regulator-always-on;
+		};
+
+		reg_vddsoc: sw1c {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1875000>;
+			regulator-always-on;
+		};
+
+		reg_gen_3v3: sw2 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_ddr_1v5a: sw3a {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <1975000>;
+			regulator-always-on;
+		};
+
+		reg_ddr_1v5b: sw3b {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <1975000>;
+			regulator-always-on;
+		};
+
+		sw4_reg: sw4 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_5v_600mA: swbst {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5150000>;
+			regulator-always-on;
+		};
+
+		reg_snvs_3v: vsnvs {
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+
+		reg_vrefddr: vrefddr {
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		reg_vgen1_1v5: vgen1 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1550000>;
+			/* not used */
+		};
+
+		reg_vgen2_1v2_eth: vgen2 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1550000>;
+			regulator-always-on;
+		};
+
+		reg_vgen3_2v8: vgen3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_vgen4_1v8: vgen4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_vgen5_1v8_eth: vgen5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_vgen6_3v3: vgen6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vmmc-supply = <&reg_3p3v>;
+	non-removable;
+	disable-wp;
+	no-sd;
+	no-sdio;
+	bus-width = <8>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	mmccard: mmccard@0 {
+		reg = <0>;
+		compatible = "mmc-card";
+		broken-hpi;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6a.dtsi
new file mode 100644
index 000000000000..68525f0205d3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6a.dtsi
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+&fec {
+	/delete-property/ interrupts;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_recovery>;
+	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmic: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+	};
+
+	sensor@48 {
+		compatible = "national,lm75";
+		reg = <0x48>;
+		vs-supply = <&reg_3p3v>;
+	};
+
+	eeprom@50 {
+		compatible = "st,24c64", "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&reg_3p3v>;
+	};
+};
+
+&iomuxc {
+	/*
+	 * This pinmuxing is required for the ERR006687 workaround. Board
+	 * DTS files that enable the FEC controller with
+	 * fsl,err006687-workaround-present must include this group.
+	 */
+	pinctrl_enet_fix: enetfixgrp {
+		fsl,pins = <
+			/* ENET ping patch */
+			MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6b.dtsi
new file mode 100644
index 000000000000..aeba0a273600
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6b.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+&i2c3 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_recovery>;
+	scl-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmic: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+	};
+
+	sensor@48 {
+		compatible = "national,lm75";
+		reg = <0x48>;
+		vs-supply = <&reg_3p3v>;
+	};
+
+	eeprom@50 {
+		compatible = "st,24c64", "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&reg_3p3v>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-ts4900.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts4900.dtsi
index 267c956d8910..f88da757edda 100644
--- a/arch/arm/boot/dts/imx6qdl-ts4900.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts4900.dtsi
@@ -95,7 +95,7 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
@@ -108,7 +108,7 @@
 };
 
 &ecspi2 {
-	cs-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts7970.dtsi
index f0be516dc28e..e2db875b61c4 100644
--- a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts7970.dtsi
@@ -73,13 +73,13 @@
 			default-state = "off";
 		};
 
-		en-usb-5v {
+		en-usb-5v-led {
 			label = "en-usb-5v";
 			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		sel_dc_usb {
+		sel-dc-usb-led {
 			label = "sel_dc_usb";
 			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -165,7 +165,7 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
@@ -179,9 +179,9 @@
 
 &ecspi2 {
 	cs-gpios = <
-		&gpio5 31 GPIO_ACTIVE_HIGH
-		&gpio7 12 GPIO_ACTIVE_HIGH
-		&gpio5 18 GPIO_ACTIVE_HIGH
+		&gpio5 31 GPIO_ACTIVE_LOW
+		&gpio7 12 GPIO_ACTIVE_LOW
+		&gpio5 18 GPIO_ACTIVE_LOW
 	>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
@@ -192,6 +192,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -226,7 +227,7 @@
 		reg = <0x28>;
 		#gpio-cells = <2>;
 		gpio-controller;
-		ngpio = <32>;
+		ngpios = <62>;
 	};
 
 	sgtl5000: codec@a {
@@ -234,6 +235,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -506,7 +508,6 @@
 };
 
 &ssi1 {
-	fsl,mode = "i2s-slave";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lcd.dtsi
index 79f2354886b7..79f2354886b7 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lcd.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-lvds.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lvds.dtsi
index 2ca2eb37e14f..2ca2eb37e14f 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6-lvds.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lvds.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-mb7.dtsi
index 410972e1dca9..99ec7a838f8d 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-mb7.dtsi
@@ -85,7 +85,7 @@
 };
 
 &i2c3 {
-	rtc: mcp7940x@6f {
+	rtc: rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6.dtsi
index c68cb90fd801..e2fe337f7d9e 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6.dtsi
@@ -92,7 +92,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user_led: user {
+		user_led: led-user {
 			label = "Heartbeat";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_user_led>;
@@ -216,7 +216,7 @@
 &audmux {
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -228,7 +228,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -259,28 +259,11 @@
 		&gpio3 19 GPIO_ACTIVE_HIGH
 	>;
 	status = "disabled";
-
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <54000000>;
-	};
 };
 
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet &pinctrl_enet_mdio &pinctrl_etnphy_rst>;
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET_REF>,
-		 <&clks IMX6QDL_CLK_ENET_REF>;
-	clock-names = "ipg", "ahb", "ptp", "enet_out";
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
 	phy-reset-post-delay = <10>;
@@ -738,14 +721,12 @@
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	#pwm-cells = <3>;
 	status = "disabled";
 };
 
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
-	#pwm-cells = <3>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi
index 828dd20cd27d..647ba5e623dd 100644
--- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi
@@ -5,6 +5,8 @@
  * Author: Fabio Estevam <fabio.estevam@freescale.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	aliases {
 		backlight = &backlight;
@@ -57,29 +59,21 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb_h1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */
-			gpio = <&gpio7 12 0>;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */
+		gpio = <&gpio7 12 0>;
+	};
 
-		reg_panel: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "lcd_panel";
-			enable-active-high;
-			gpio = <&gpio1 2 0>;
-		};
+	reg_panel: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd_panel";
+		enable-active-high;
+		gpio = <&gpio1 2 0>;
 	};
 
 	sound {
@@ -98,7 +92,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
@@ -226,6 +220,7 @@
 				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
 			>;
 		};
 
@@ -292,7 +287,7 @@
 	pinctrl-0 = <&pinctrl_usbh>;
 	vbus-supply = <&reg_usb_h1_vbus>;
 	clocks = <&clks IMX6QDL_CLK_CKO>;
-	status = "okay";
+	status = "disabled";
 };
 
 &usbotg {
@@ -304,7 +299,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	non-removable;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-var-dart.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-dart.dtsi
index c41cac502bac..200559d7158d 100644
--- a/arch/arm/boot/dts/imx6qdl-var-dart.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-dart.dtsi
@@ -39,7 +39,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -51,7 +51,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-var-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-som.dtsi
new file mode 100644
index 000000000000..a1ea33c4eeb7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-som.dtsi
@@ -0,0 +1,569 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite VAR-SOM-MX6 Module
+ *
+ * Copyright 2011 Linaro Ltd.
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright (C) 2014-2016 Variscite, Ltd.
+ * Author: Donio Ron <ron.d@variscite.com>
+ * Copyright 2022 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	model = "Variscite VAR-SOM-MX6 module";
+	compatible = "variscite,var-som-imx6q", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbud {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_wl18xx_vmmc: regulator-wl18xx {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1807";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <70000>;
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "var-som-audio";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&sound_codec>;
+		simple-audio-card,frame-master = <&sound_codec>;
+		simple-audio-card,widgets = "Headphone", "Headphone Jack",
+					    "Line", "Line In", "Microphone", "Mic Jack";
+		simple-audio-card,routing = "Headphone Jack", "HPLOUT",
+					    "Headphone Jack", "HPROUT",
+					    "LINE1L", "Line In",
+					    "LINE1R", "Line In";
+
+		sound_cpu: simple-audio-card,cpu {
+			sound-dai = <&ssi2>;
+		};
+
+		sound_codec: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&clks IMX6QDL_CLK_CKO>;
+		};
+	};
+
+	rfkill {
+		compatible = "rfkill-gpio";
+		name = "rfkill";
+		radio-type = "bluetooth";
+		shutdown-gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi2 {
+		fsl,audmux-port = <1>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_SYN |
+			IMX_AUDMUX_V2_PTCR_TFSDIR |
+			IMX_AUDMUX_V2_PTCR_TFSEL(2) |
+			IMX_AUDMUX_V2_PTCR_TCLKDIR |
+			IMX_AUDMUX_V2_PTCR_TCSEL(2))
+			IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-aud3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN
+			IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+		>;
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rgmii_phy: ethernet-phy@7 {
+			reg = <7>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+
+	tlv320aic3106: audio-codec@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		#sound-dai-cells = <0>;
+		DRVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_3p3v>;
+		IOVDD-supply = <&reg_3p3v>;
+		DVDD-supply = <&reg_1p8v>;
+		ai3x-ocmv = <0>;
+		reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+		ai3x-gpio-func = <
+			0 /* AIC3X_GPIO1_FUNC_DISABLED */
+			5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
+		>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			/* Audio Clock */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0
+		>;
+	};
+
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			/* Bluetooth/wifi enable */
+			MX6QDL_PAD_SD3_DAT6__GPIO6_IO18		0x1b0b1
+			/* Wifi Slow Clock */
+			MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT	0x000b0
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet_irq: enetirqgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_6__ENET_IRQ	0x000b1
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* CTW6120 IRQ */
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07		0xb0b1
+			/* SDMMC2 CD/WP */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA	0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			/* PMIC INT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_RTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17069
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x10069
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x17069
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x17069
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x17069
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x17069
+			/* WL_EN */
+			MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x13059
+			/* WL_IRQ */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x13059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x170B9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x100B9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x170B9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x170B9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x170B9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x170B9
+			/* WL_EN */
+			MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x130B9
+			/* WL_IRQ */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x130B9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x170F9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x100F9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x170F9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x170F9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x170F9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x170F9
+			/* WL_EN */
+			MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x130F9
+			/* WL_IRQ */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x130F9
+		>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&reg_arm {
+	vin-supply = <&sw1a_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&vgen5_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&vgen5_reg>;
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg_var>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <0x5>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <0x5>;
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_wl18xx_vmmc>;
+	non-removable;
+	wakeup-source;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi: wifi@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+		ref-clock-frequency = <38400000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1-12inch.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1-12inch.dtsi
new file mode 100644
index 000000000000..73f381e14467
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1-12inch.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Protonic Holland
+ */
+
+/ {
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		power-button {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg121xglp";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ9031RNX PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "ETH_MDIO", "",
+		"", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+			"HITCH_IN_OUT",
+		"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+			"ISB_LED";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+			"RGMII_TD3",
+		"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+			"RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x1b0b1
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1.dtsi
new file mode 100644
index 000000000000..96e4f4b0b248
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1.dtsi
@@ -0,0 +1,712 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight_lcd: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	backlight_led: backlight-led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
+	/* only for backwards compatibility with old HW */
+	backlight_isb: backlight-isb {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 8 48 255>;
+		num-interpolated-steps = <5>;
+		default-brightness-level = <0>;
+		power-supply = <&reg_3v3>;
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
+	counter-0 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter0>;
+		gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-1 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter1>;
+		gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-2 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter2>;
+		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "debug1";
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		led-2 {
+			label = "power_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led-3 {
+			label = "isb_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0				IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	termination-ohms = <150>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&gpio2 {
+	gpio-line-names =
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
+		"", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+		"POWER_LED", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+			"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
+		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+			"YACO_RESET";
+};
+
+&gpio7 {
+	gpio-line-names =
+		"EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+			"EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+		"EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+		"", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	video-decoder@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	tsens0: temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_counter0: counter0grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00			0x1b000
+		>;
+	};
+
+	pinctrl_counter1: counter1grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01			0x1b000
+		>;
+	};
+
+	pinctrl_counter2: counter2grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02			0x1b000
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* ITU656_nRESET */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
+			/* CAM1_MIRROR */
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
+			/* CAM2_MIRROR */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
+			/* CAM_nDETECT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
+			/* ISB_IN1 */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
+			/* ISB_nIN2 */
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
+			/* WARN_LIGHT */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
+			/* ON2_FB */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
+			/* YACO_nIRQ */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
+			/* YACO_BOOT0 */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
+			/* YACO_nRESET */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
+			/* FORCE_ON1 */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+			/* AUDIO_nRESET */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
+			/* ITU656_nPDN */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
+
+			/* New in HW revision 1 */
+			/* ON1_FB */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
+			/* DIP1_FB */
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG0 */
+			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
+			/* DEBUG1 */
+			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
+			/* POWER_LED */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+			/* ISB_LED */
+			MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31		0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	/* YaCO Touchscreen UART */
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revb1.dtsi
index e781a45785ed..e781a45785ed 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revb1.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revc1.dtsi
index 3874e74703f0..3874e74703f0 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revc1.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revd1.dtsi
index 93909796885a..9b8c9c23ab54 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revd1.dtsi
@@ -27,7 +27,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -142,7 +142,6 @@
 	imx6qdl-wandboard {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				MX6QDL_PAD_EIM_D22__USB_OTG_PWR		0x80000000	/* USB Power Enable */
 				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* USDHC1 CD */
 				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
 				MX6QDL_PAD_EIM_D29__GPIO3_IO29   	0x1f0b1		/* RGMII PHY reset */
@@ -166,7 +165,6 @@
 				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
 				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard.dtsi
index c070893c509e..38abb6b50f6c 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard.dtsi
@@ -97,15 +97,21 @@
 
 &i2c1 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
 &i2c2 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	codec: sgtl5000@a {
@@ -113,6 +119,7 @@
 		pinctrl-0 = <&pinctrl_mclk>;
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -125,7 +132,6 @@
 		pinctrl-0 = <&pinctrl_ov5645>;
 		reg = <0x3c>;
 		clocks = <&clks IMX6QDL_CLK_CKO2>;
-		clock-names = "xclk";
 		clock-frequency = <24000000>;
 		vdddo-supply = <&reg_1p8v>;
 		vdda-supply = <&reg_2p8v>;
@@ -185,6 +191,13 @@
 			>;
 		};
 
+		pinctrl_i2c1_gpio: i2c1gpiogrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x4001b8b0
+				MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x4001b8b0
+			>;
+		};
+
 		pinctrl_i2c2: i2c2grp {
 			fsl,pins = <
 				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
@@ -192,6 +205,13 @@
 			>;
 		};
 
+		pinctrl_i2c2_gpio: i2c2gpiogrp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x4001b8b0
+				MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x4001b8b0
+			>;
+		};
+
 		pinctrl_mclk: mclkgrp {
 			fsl,pins = <
 				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0
@@ -289,6 +309,7 @@
 
 		ethphy: ethernet-phy@1 {
 			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-zii-rdu2.dtsi
index a2a4f33a3e3e..9ff183e4e069 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-zii-rdu2.dtsi
@@ -60,18 +60,6 @@
 		regulator-always-on;
 	};
 
-	reg_5p0v_user_usb: regulator-5p0v-user-usb {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_user_usb>;
-		vin-supply = <&reg_5p0v_main>;
-		regulator-name = "5V_USER_USB";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
-		startup-delay-us = <1000>;
-	};
-
 	reg_3p3v_pmic: regulator-3p3v-pmic {
 		compatible = "regulator-fixed";
 		vin-supply = <&reg_12p0v>;
@@ -124,17 +112,17 @@
 
 	sound1 {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "Front";
+		simple-audio-card,name = "front";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&sound1_codec>;
 		simple-audio-card,frame-master = <&sound1_codec>;
 		simple-audio-card,widgets =
 			"Headphone", "Headphone Jack";
 		simple-audio-card,routing =
-			"Headphone Jack", "HPLEFT",
-			"Headphone Jack", "HPRIGHT",
-			"LEFTIN", "HPL",
-			"RIGHTIN", "HPR";
+			"Headphone Jack", "HPA1 HPLEFT",
+			"Headphone Jack", "HPA1 HPRIGHT",
+			"HPA1 LEFTIN", "HPL",
+			"HPA1 RIGHTIN", "HPR";
 		simple-audio-card,aux-devs = <&hpa1>;
 
 		sound1_cpu: simple-audio-card,cpu {
@@ -149,17 +137,17 @@
 
 	sound2 {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "Back";
+		simple-audio-card,name = "periph";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&sound2_codec>;
 		simple-audio-card,frame-master = <&sound2_codec>;
 		simple-audio-card,widgets =
 			"Headphone", "Headphone Jack";
 		simple-audio-card,routing =
-			"Headphone Jack", "HPLEFT",
-			"Headphone Jack", "HPRIGHT",
-			"LEFTIN", "HPL",
-			"RIGHTIN", "HPR";
+			"Headphone Jack", "HPA1 HPLEFT",
+			"Headphone Jack", "HPA1 HPRIGHT",
+			"HPA1 LEFTIN", "HPL",
+			"HPA1 RIGHTIN", "HPR";
 		simple-audio-card,aux-devs = <&hpa2>;
 
 		sound2_cpu: simple-audio-card,cpu {
@@ -228,6 +216,13 @@
 	};
 };
 
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+	                         <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
 &cpu0 {
 	fsl,soc-operating-points = <
 		/* ARM kHz  SOC-PU uV */
@@ -282,7 +277,7 @@
 	pinctrl-0 = <&pinctrl_uart4>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -321,7 +316,7 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	flash@0 {
@@ -331,6 +326,39 @@
 	};
 };
 
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio3_hog>;
+
+	usb-emulation-hog {
+		gpio-hog;
+		gpios = <19 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "usb-emulation";
+	};
+
+	usb-mode1-hog {
+		gpio-hog;
+		gpios = <20 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-mode1";
+	};
+
+	usb-pwr-hog {
+		gpio-hog;
+		gpios = <22 GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "usb-pwr-ctrl-en-n";
+	};
+
+	usb-mode2-hog {
+		gpio-hog;
+		gpios = <23 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-mode2";
+	};
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
@@ -371,6 +399,7 @@
 		reg = <0x60>;
 		power-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		Vdd-supply = <&reg_5p0v_main>;
+		sound-name-prefix = "HPA1";
 	};
 
 	edp-bridge@68 {
@@ -570,6 +599,8 @@
 			touchscreen-inverted-x;
 			touchscreen-swapped-x-y;
 			syna,sensor-type = <1>;
+			syna,delta-x-threshold = <5>;
+			syna,delta-y-threshold = <10>;
 		};
 
 		rmi4-f12@12 {
@@ -592,6 +623,16 @@
 		status = "disabled";
 	};
 
+	reg_5p0v_user_usb: charger@32 {
+		compatible = "microchip,ucs1002";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ucs1002_pins>;
+		reg = <0x32>;
+		interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>,
+		                      <&gpio3 21 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "a_det", "alert";
+	};
+
 	hpa1: amp@60 {
 		compatible = "ti,tpa6130a2";
 		pinctrl-names = "default";
@@ -599,6 +640,7 @@
 		reg = <0x60>;
 		power-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 		Vdd-supply = <&reg_5p0v_main>;
+		sound-name-prefix = "HPA1";
 	};
 };
 
@@ -629,7 +671,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
@@ -642,7 +684,7 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
@@ -681,6 +723,8 @@
 	mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clock-frequency = <12500000>;
+		suppress-preamble;
 		status = "okay";
 
 		switch: switch@0 {
@@ -713,7 +757,7 @@
 
 				port@2 {
 					reg = <2>;
-					label = "cpu";
+					phy-mode = "rev-rmii";
 					ethernet = <&fec>;
 
 					fixed-link {
@@ -776,6 +820,7 @@
 &usbh1 {
 	vbus-supply = <&reg_5p0v_main>;
 	disable-over-current;
+	maximum-speed = "full-speed";
 	status = "okay";
 };
 
@@ -803,7 +848,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -815,7 +860,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -823,7 +868,7 @@
 		>;
 	};
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -835,7 +880,7 @@
 		>;
 	};
 
-	aud5 {
+	mux-aud5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -844,10 +889,6 @@
 	};
 };
 
-&wdog1 {
-	status = "disabled";
-};
-
 &iomuxc {
 	pinctrl_accel: accelgrp {
 		fsl,pins = <
@@ -936,24 +977,33 @@
 		>;
 	};
 
+	pinctrl_gpio3_hog: gpio3hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x1b0b0
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
-			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b811
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b811
 		>;
 	};
 
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b811
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b811
 		>;
 	};
 
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
-			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b811
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b811
 		>;
 	};
 
@@ -983,12 +1033,6 @@
 		>;
 	};
 
-	pinctrl_reg_user_usb: usbotggrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x40000038
-		>;
-	};
-
 	pinctrl_rmii_phy_irq: phygrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x40010000
@@ -1048,6 +1092,13 @@
 		>;
 	};
 
+	pinctrl_ucs1002_pins: ucs1002grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02  	0x1b0b0
+			MX6QDL_PAD_EIM_D21__GPIO3_IO21  	0x1b0b0
+		>;
+	};
+
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x10059
@@ -1056,7 +1107,6 @@
 			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
 			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
 			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x40010040
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x40010040
 		>;
 	};
@@ -1069,7 +1119,6 @@
 			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x40010040
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x40010040
 
 		>;
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index e6b4b8525f98..81142c523fa8 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -45,40 +45,34 @@
 		spi1 = &ecspi2;
 		spi2 = &ecspi3;
 		spi3 = &ecspi4;
+		usb0 = &usbotg;
+		usb1 = &usbh1;
+		usb2 = &usbh2;
+		usb3 = &usbh3;
 		usbphy0 = &usbphy1;
 		usbphy1 = &usbphy2;
 	};
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};
 
-	tempmon: tempmon {
-		compatible = "fsl,imx6q-tempmon";
-		interrupt-parent = <&gpc>;
-		interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
-		fsl,tempmon = <&anatop>;
-		fsl,tempmon-data = <&ocotp>;
-		clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-		#thermal-sensor-cells = <0>;
-	};
-
 	ldb: ldb {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -149,27 +143,26 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&gpc>;
 		ranges;
 
-		dma_apbh: dma-apbh@110000 {
+		dma_apbh: dma-controller@110000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x00110000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX6QDL_CLK_APBH_DMA>;
 		};
 
-		gpmi: gpmi-nand@112000 {
+		gpmi: nand-controller@112000 {
 			compatible = "fsl,imx6q-gpmi-nand";
 			reg = <0x00112000 0x2000>, <0x00114000 0x2000>;
 			reg-names = "gpmi-nand", "bch";
@@ -188,8 +181,6 @@
 		};
 
 		hdmi: hdmi@120000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			reg = <0x00120000 0x9000>;
 			interrupts = <0 115 0x04>;
 			gpr = <&gpr>;
@@ -198,19 +189,24 @@
 			clock-names = "iahb", "isfr";
 			status = "disabled";
 
-			port@0 {
-				reg = <0>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
 
-				hdmi_mux_0: endpoint {
-					remote-endpoint = <&ipu1_di0_hdmi>;
+					hdmi_mux_0: endpoint {
+						remote-endpoint = <&ipu1_di0_hdmi>;
+					};
 				};
-			};
 
-			port@1 {
-				reg = <1>;
+				port@1 {
+					reg = <1>;
 
-				hdmi_mux_1: endpoint {
-					remote-endpoint = <&ipu1_di1_hdmi>;
+					hdmi_mux_1: endpoint {
+						remote-endpoint = <&ipu1_di1_hdmi>;
+					};
 				};
 			};
 		};
@@ -255,7 +251,7 @@
 			interrupt-parent = <&intc>;
 		};
 
-		L2: l2-cache@a02000 {
+		L2: cache-controller@a02000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x00a02000 0x1000>;
 			interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>;
@@ -267,7 +263,7 @@
 		};
 
 		pcie: pcie@1ffc000 {
-			compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+			compatible = "fsl,imx6q-pcie";
 			reg = <0x01ffc000 0x04000>,
 			      <0x01f00000 0x80000>;
 			reg-names = "dbi", "config";
@@ -275,10 +271,9 @@
 			#size-cells = <2>;
 			device_type = "pci";
 			bus-range = <0x00 0xff>;
-			ranges = <0x81000000 0 0          0x01f80000 0 0x00010000 /* downstream I/O */
-				  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0 0          0x01f80000 0 0x00010000>, /* downstream I/O */
+				 <0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			num-viewport = <4>;
 			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
@@ -294,7 +289,7 @@
 			status = "disabled";
 		};
 
-		aips-bus@2000000 { /* AIPS1 */
+		aips1: bus@2000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -337,7 +332,7 @@
 					clocks = <&clks IMX6QDL_CLK_ECSPI1>,
 						 <&clks IMX6QDL_CLK_ECSPI1>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 3 8 1>, <&sdma 4 8 2>;
+					dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};
@@ -351,7 +346,7 @@
 					clocks = <&clks IMX6QDL_CLK_ECSPI2>,
 						 <&clks IMX6QDL_CLK_ECSPI2>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 5 8 1>, <&sdma 6 8 2>;
+					dmas = <&sdma 5 7 1>, <&sdma 6 7 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};
@@ -365,7 +360,7 @@
 					clocks = <&clks IMX6QDL_CLK_ECSPI3>,
 						 <&clks IMX6QDL_CLK_ECSPI3>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 7 8 1>, <&sdma 8 8 2>;
+					dmas = <&sdma 7 7 1>, <&sdma 8 7 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};
@@ -379,7 +374,7 @@
 					clocks = <&clks IMX6QDL_CLK_ECSPI4>,
 						 <&clks IMX6QDL_CLK_ECSPI4>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 9 8 1>, <&sdma 10 8 2>;
+					dmas = <&sdma 9 7 1>, <&sdma 10 7 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};
@@ -480,12 +475,12 @@
 						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 							"txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
 
-				spba@203c000 {
+				spba-bus@203c000 {
 					reg = <0x0203c000 0x4000>;
 				};
 			};
@@ -509,7 +504,7 @@
 			};
 
 			pwm1: pwm@2080000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
 				reg = <0x02080000 0x4000>;
 				interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>;
@@ -520,7 +515,7 @@
 			};
 
 			pwm2: pwm@2084000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
 				reg = <0x02084000 0x4000>;
 				interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
@@ -531,7 +526,7 @@
 			};
 
 			pwm3: pwm@2088000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
 				reg = <0x02088000 0x4000>;
 				interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
@@ -542,7 +537,7 @@
 			};
 
 			pwm4: pwm@208c000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
 				reg = <0x0208c000 0x4000>;
 				interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
@@ -552,29 +547,29 @@
 				status = "disabled";
 			};
 
-			can1: flexcan@2090000 {
+			can1: can@2090000 {
 				compatible = "fsl,imx6q-flexcan";
 				reg = <0x02090000 0x4000>;
 				interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_CAN1_IPG>,
 					 <&clks IMX6QDL_CLK_CAN1_SERIAL>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x34 28 0x10 17>;
+				fsl,stop-mode = <&gpr 0x34 28>;
 				status = "disabled";
 			};
 
-			can2: flexcan@2094000 {
+			can2: can@2094000 {
 				compatible = "fsl,imx6q-flexcan";
 				reg = <0x02094000 0x4000>;
 				interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_CAN2_IPG>,
 					 <&clks IMX6QDL_CLK_CAN2_SERIAL>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x34 29 0x10 18>;
+				fsl,stop-mode = <&gpr 0x34 29>;
 				status = "disabled";
 			};
 
-			gpt: gpt@2098000 {
+			gpt: timer@2098000 {
 				compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -661,7 +656,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			kpp: kpp@20b8000 {
+			kpp: keypad@20b8000 {
 				compatible = "fsl,imx6q-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -669,14 +664,14 @@
 				status = "disabled";
 			};
 
-			wdog1: wdog@20bc000 {
+			wdog1: watchdog@20bc000 {
 				compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
 				reg = <0x020bc000 0x4000>;
 				interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_IPG>;
 			};
 
-			wdog2: wdog@20c0000 {
+			wdog2: watchdog@20c0000 {
 				compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
 				reg = <0x020c0000 0x4000>;
 				interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>;
@@ -684,7 +679,7 @@
 				status = "disabled";
 			};
 
-			clks: ccm@20c4000 {
+			clks: clock-controller@20c4000 {
 				compatible = "fsl,imx6q-ccm";
 				reg = <0x020c4000 0x4000>;
 				interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>,
@@ -766,7 +761,7 @@
 					regulator-name = "vddpu";
 					regulator-min-microvolt = <725000>;
 					regulator-max-microvolt = <1450000>;
-					regulator-enable-ramp-delay = <150>;
+					regulator-enable-ramp-delay = <380>;
 					anatop-reg-offset = <0x140>;
 					anatop-vol-bit-shift = <9>;
 					anatop-vol-bit-width = <5>;
@@ -794,6 +789,17 @@
 					anatop-min-voltage = <725000>;
 					anatop-max-voltage = <1450000>;
 				};
+
+				tempmon: tempmon {
+					compatible = "fsl,imx6q-tempmon";
+					interrupt-parent = <&gpc>;
+					interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
+					fsl,tempmon = <&anatop>;
+					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+					nvmem-cell-names = "calib", "temp_grade";
+					clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+					#thermal-sensor-cells = <0>;
+				};
 			};
 
 			usbphy1: usbphy@20c9000 {
@@ -857,7 +863,7 @@
 				interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6q-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -870,8 +876,7 @@
 				reg = <0x020dc000 0x4000>;
 				interrupt-controller;
 				#interrupt-cells = <3>;
-				interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
-					     <0 90 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&intc>;
 				clocks = <&clks IMX6QDL_CLK_IPG>;
 				clock-names = "ipg";
@@ -908,7 +913,7 @@
 				};
 			};
 
-			iomuxc: iomuxc@20e0000 {
+			iomuxc: pinctrl@20e0000 {
 				compatible = "fsl,imx6dl-iomuxc", "fsl,imx6q-iomuxc";
 				reg = <0x20e0000 0x4000>;
 			};
@@ -923,7 +928,7 @@
 				interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -935,14 +940,14 @@
 			};
 		};
 
-		aips-bus@2100000 { /* AIPS2 */
+		aips2: bus@2100000 { /* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x02100000 0x100000>;
 			ranges;
 
-			crypto: caam@2100000 {
+			crypto: crypto@2100000 {
 				compatible = "fsl,sec-v4.0";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -954,13 +959,13 @@
 					 <&clks IMX6QDL_CLK_EIM_SLOW>;
 				clock-names = "mem", "aclk", "ipg", "emi_slow";
 
-				sec_jr0: jr0@1000 {
+				sec_jr0: jr@1000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr1: jr1@2000 {
+				sec_jr1: jr@2000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x2000 0x1000>;
 					interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
@@ -1039,13 +1044,16 @@
 				compatible = "fsl,imx6q-fec";
 				reg = <0x02188000 0x4000>;
 				interrupt-names = "int0", "pps";
-				interrupts-extended =
-					<&intc 0 118 IRQ_TYPE_LEVEL_HIGH>,
-					<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>,
+					     <0 119 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_ENET>,
 					 <&clks IMX6QDL_CLK_ENET>,
-					 <&clks IMX6QDL_CLK_ENET_REF>;
-				clock-names = "ipg", "ahb", "ptp";
+					 <&clks IMX6QDL_CLK_ENET_REF>,
+					 <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+				clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+				fsl,stop-mode = <&gpr 0x34 27>;
+				nvmem-cells = <&fec_mac_addr>;
+				nvmem-cell-names = "mac-address";
 				status = "disabled";
 			};
 
@@ -1056,7 +1064,7 @@
 					     <0 126 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			usdhc1: usdhc@2190000 {
+			usdhc1: mmc@2190000 {
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -1068,7 +1076,7 @@
 				status = "disabled";
 			};
 
-			usdhc2: usdhc@2194000 {
+			usdhc2: mmc@2194000 {
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -1080,7 +1088,7 @@
 				status = "disabled";
 			};
 
-			usdhc3: usdhc@2198000 {
+			usdhc3: mmc@2198000 {
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x02198000 0x4000>;
 				interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
@@ -1092,7 +1100,7 @@
 				status = "disabled";
 			};
 
-			usdhc4: usdhc@219c000 {
+			usdhc4: mmc@219c000 {
 				compatible = "fsl,imx6q-usdhc";
 				reg = <0x0219c000 0x4000>;
 				interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
@@ -1161,10 +1169,28 @@
 				status = "disabled";
 			};
 
-			ocotp: ocotp@21bc000 {
+			ocotp: efuse@21bc000 {
 				compatible = "fsl,imx6q-ocotp", "syscon";
 				reg = <0x021bc000 0x4000>;
 				clocks = <&clks IMX6QDL_CLK_IIM>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
+
+				tempmon_calib: calib@38 {
+					reg = <0x38 4>;
+				};
+
+				tempmon_temp_grade: temp-grade@20 {
+					reg = <0x20 4>;
+				};
+
+				fec_mac_addr: mac-addr@88 {
+					reg = <0x88 6>;
+				};
 			};
 
 			tzasc@21d0000 { /* TZASC1 */
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-mba6b.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-mba6b.dts
new file mode 100644
index 000000000000..eee2e09d6e94
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-mba6b.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2015-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6qp-tqma6b.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6b.dtsi"
+#include "imx6q-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6QP on MBa6x";
+	compatible = "tq,imx6qp-mba6x-b", "tq,mba6b",
+		     "tq,imx6qp-tqma6qp-b", "fsl,imx6qp";
+};
diff --git a/arch/arm/boot/dts/imx6qp-nitrogen6_max.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dts
index 741d1ed338ca..741d1ed338ca 100644
--- a/arch/arm/boot/dts/imx6qp-nitrogen6_max.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dts
diff --git a/arch/arm/boot/dts/imx6qp-nitrogen6_som2.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_som2.dts
index 1593ac86b2a4..1593ac86b2a4 100644
--- a/arch/arm/boot/dts/imx6qp-nitrogen6_som2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_som2.dts
diff --git a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-phytec-mira-rdk-nand.dts
index f27d7ab42626..a18266598d39 100644
--- a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
 #include "imx6qp.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira QuadPlus Carrier-Board with NAND";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-prtwd3.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-prtwd3.dts
new file mode 100644
index 000000000000..ae00d538a4df
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-prtwd3.dts
@@ -0,0 +1,557 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2018 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6qp.dtsi"
+
+/ {
+	model = "Protonic WD3 board";
+	compatible = "prt,prtwd3", "fsl,imx6qp";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	clock_ksz8081: clock-ksz8081 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	clock_ksz9031: clock-ksz9031 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_mcp251xfd: clock-mcp251xfd {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <20000000>;
+	};
+
+	clock_sja1105: clock-sja1105 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	mdio {
+		compatible = "virtual,mdio-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mdio>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio5 6 GPIO_ACTIVE_HIGH
+			 &gpio5 7 GPIO_ACTIVE_HIGH>;
+
+		/* Microchip KSZ8081 */
+		usbeth_phy: ethernet-phy@3 {
+			reg = <0x3>;
+
+			interrupts-extended = <&gpio5 12 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <1000>;
+			clocks = <&clock_ksz8081>;
+			clock-names = "rmii-ref";
+			micrel,led-mode = <0>;
+		};
+
+		tja1102_phy0: ethernet-phy@4 {
+			reg = <0x4>;
+
+			interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <20>;
+			reset-deassert-us = <2000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tja1102_phy1: ethernet-phy@5 {
+				reg = <0x5>;
+
+				interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+			};
+		};
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usdhc2_wifi_pwrseq: usdhc2-wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	switch@0 {
+		compatible = "nxp,sja1105q";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-rx-delay-us = <1>;
+		spi-tx-delay-us = <1>;
+		spi-cpha;
+
+		reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
+
+		clocks = <&clock_sja1105>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "usb";
+				phy-handle = <&usbeth_phy>;
+				phy-mode = "rmii";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "t1slave";
+				phy-handle = <&tja1102_phy1>;
+				phy-mode = "rmii";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "t1master";
+				phy-handle = <&tja1102_phy0>;
+				phy-mode = "rmii";
+
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "rj45";
+				phy-handle = <&rgmii_phy>;
+				phy-mode = "rgmii-id";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "cpu";
+				ethernet = <&fec>;
+				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <2000>;
+				tx-internal-delay-ps = <2000>;
+
+				fixed-link {
+					speed = <100>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+
+	can@0 {
+		compatible = "microchip,mcp251xfd";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can2>;
+		reg = <0>;
+		clocks = <&clock_mcp251xfd>;
+		spi-max-frequency = <10000000>;
+		interrupts-extended = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF>;
+	assigned-clock-rates = <125000000>;
+	status = "okay";
+
+	phy-mode = "rgmii";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ9031 */
+		rgmii_phy: ethernet-phy@2 {
+			reg = <2>;
+
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <1000>;
+
+			clocks = <&clock_ksz9031>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "SD1_CD", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "PHY3_RESET", "", "", "PHY3_INT", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "BOARD_ID3",
+			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "", "", "", "", "", "", "",
+		"", "", "ECSPI2_SS0", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "USB_OTG_OC", "USB_OTG_PWR", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+		"", "", "", "", "", "", "", "",
+		"ECSPI3_SS0", "CANFD_INT", "USB_ETH_RESET", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "SW_RESET", "", "",
+		"PHY12_INT", "PHY12_RESET", "PHY12_EN", "PHY0_RESET",
+			"PHY0_INT", "", "", "",
+		"", "", "DISP1_EN", "DISP1_LR", "DISP1_TS_IRQ", "LVDS1_PD",
+			"", "",
+		"", "LVDS1_INT", "", "", "DISP0_LR", "DISP0_TS_IRQ",
+			"DISP0_EN", "CAM_GPIO0";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"LVDS0_INT", "LVDS0_PD", "CAM_INT", "CAM_GPIO1", "CAM_PD",
+			"CAM_LOCK", "", "POWER_TG",
+		"POWER_VSEL", "", "WLAN_REG_ON", "USB_ETH_CHG", "", "",
+			"USB_ETH_CHG_ID0", "USB_ETH_CHG_ID1",
+		"USB_ETH_CHG_ID2", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* VIN */
+		channel@4 {
+			reg = <4>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+
+		/* VBUS */
+		channel@5 {
+			reg = <5>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+
+		/* ICHG */
+		channel@6 {
+			reg = <6>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <1>;
+			ti,datarate = <3>;
+		};
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	no-1-8-v;
+	non-removable;
+	mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			/* CAN2_nINT */
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25		0x1b0b1
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13070
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO			0x100b1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK			0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI			0x100b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26			0x000b1
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK		0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI		0x100b1
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO		0x100b1
+			/* CS */
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24		0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
+
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
+
+			/* Configure clock provider for RGMII ref clock */
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x4001b0b0
+			/* Configure clock consumer for RGMII ref clock */
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
+
+			/* SJA1105Q switch reset */
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05		0x10030
+
+			/* phy3/rgmii_phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x10030
+			/* phy3/rgmii_phy int */
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x40010000
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_mdio: mdiogrp {
+		fsl,pins = <
+			/* phy0/usbeth_phy reset */
+			MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11		0x10030
+			/* phy0/usbeth_phy int */
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12		0x100b1
+
+			/* phy12/tja1102_phy0 reset */
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09		0x10030
+			/* phy12/tja1102_phy0 int */
+			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08		0x100b1
+			/* phy12/tja1102_phy0 enable. Set 100K pull-up */
+			MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10		0x1f030
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD			0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK			0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0			0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1			0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2			0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3			0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+
+	pinctrl_wifi_npd: wifinpd {
+		fsl,pins = <
+			/* WL_REG_ON */
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10		0x13069
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qp-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
index d4caeeb0af70..2bb3bfb18ec3 100644
--- a/arch/arm/boot/dts/imx6qp-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
@@ -47,7 +47,12 @@
 };
 
 &pcie {
-	status = "disabled";
+	reset-gpio = <&max7310_c 5 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
 };
 
 &vgen3_reg {
diff --git a/arch/arm/boot/dts/imx6qp-sabresd.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-sabresd.dts
index f1b9cb104fdd..f69eec18d865 100644
--- a/arch/arm/boot/dts/imx6qp-sabresd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabresd.dts
@@ -50,6 +50,14 @@
 	};
 };
 
+&vgen3_reg {
+	regulator-always-on;
+};
+
 &pcie {
-	status = "disabled";
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qp-tqma6b.dtsi
new file mode 100644
index 000000000000..bb6ff7c64b27
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tqma6b.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ */
+
+#include "imx6q.dtsi"
+#include "imx6qp.dtsi"
+#include "imx6qdl-tqma6b.dtsi"
+#include "imx6qdl-tqma6.dtsi"
+
+/ {
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8037-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037-mb7.dts
index 92b38e6699aa..92b38e6699aa 100644
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8037-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037-mb7.dts
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8037.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037.dts
index ffc0f2ee11d2..ffc0f2ee11d2 100644
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8037.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037.dts
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8137-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137-mb7.dts
index 07ad70718aec..07ad70718aec 100644
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8137-mb7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137-mb7.dts
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8137.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137.dts
index dd494d587014..dd494d587014 100644
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8137.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-vicutp.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-vicutp.dts
new file mode 100644
index 000000000000..49ff145fffe5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-vicutp.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
+
+/ {
+	model = "Kverneland UT1P Board";
+	compatible = "kvg,vicutp", "fsl,imx6qp";
+};
diff --git a/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-wandboard-revd1.dts
index 08d8b78a2096..08d8b78a2096 100644
--- a/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-wandboard-revd1.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-crux-plus.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-crux-plus.dts
new file mode 100644
index 000000000000..afaf4a6759d4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-crux-plus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Crux+ i.MX6QuadPlus board";
+	compatible = "ysoft,imx6qp-yapp4-crux-plus", "fsl,imx6qp";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&uart2 {
+	status = "disabled";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-pegasus-plus.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-pegasus-plus.dts
new file mode 100644
index 000000000000..4a961a33bf2d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-pegasus-plus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Pegasus+ i.MX6QuadPlus board";
+	compatible = "ysoft,imx6qp-yapp4-pegasus-plus", "fsl,imx6qp";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qp-zii-rdu2.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-zii-rdu2.dts
index 57de447c4609..57de447c4609 100644
--- a/arch/arm/boot/dts/imx6qp-zii-rdu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-zii-rdu2.dts
diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qp.dtsi
index 5f51f8e5c1fa..fc164991d2ae 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp.dtsi
@@ -9,16 +9,22 @@
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-		aips-bus@2100000 {
+		bus@2100000 {
 			pre1: pre@21c8000 {
 				compatible = "fsl,imx6qp-pre";
 				reg = <0x021c8000 0x1000>;
@@ -77,7 +83,6 @@
 };
 
 &fec {
-	/delete-property/interrupts-extended;
 	interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>,
 		     <0 119 IRQ_TYPE_LEVEL_HIGH>;
 };
@@ -111,5 +116,5 @@
 };
 
 &pcie {
-	compatible = "fsl,imx6qp-pcie", "snps,dw-pcie";
+	compatible = "fsl,imx6qp-pcie";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6s-dhcom-drc02.dts b/arch/arm/boot/dts/nxp/imx/imx6s-dhcom-drc02.dts
new file mode 100644
index 000000000000..4077b607c29e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6s-dhcom-drc02.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 DH electronics GmbH
+ *
+ * DHCOM iMX6 variant:
+ * DHCM-iMX6S-C0800-R102-F0409-E-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 493-400 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+/*
+ * The kernel only distinguishes between i.MX6 Quad and DualLite,
+ * but the Solo is actually a DualLite with only one CPU. So use
+ * DualLite for the Solo and disable one CPU node.
+ */
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-dhcom-som.dtsi"
+#include "imx6qdl-dhcom-drc02.dtsi"
+
+/ {
+	model = "DH electronics i.MX6S DHCOM on DRC02";
+	compatible = "dh,imx6s-dhcom-drc02", "dh,imx6s-dhcom-som",
+		     "fsl,imx6dl";
+
+	cpus {
+		/delete-node/ cpu@1;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
index 4829aa682aeb..239bc6dfc584 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
@@ -33,7 +33,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -94,6 +94,8 @@
 
 	sound {
 		compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
 		model = "wm8962-audio";
 		ssi-controller = <&ssi2>;
 		audio-codec = <&codec>;
@@ -106,6 +108,7 @@
 			"IN3R", "AMIC";
 		mux-int-port = <2>;
 		mux-ext-port = <3>;
+		hp-det-gpio = <&gpio4 19 GPIO_ACTIVE_LOW>;
 	};
 
 	panel {
@@ -129,12 +132,12 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio4 11 0>;
+	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -157,7 +160,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -343,6 +346,12 @@
 			>;
 		};
 
+		pinctrl_hp: hpgrp {
+			fsl,pins = <
+				MX6SL_PAD_FEC_RX_ER__GPIO4_IO19	  0x1b0b0
+			>;
+		};
+
 		pinctrl_i2c1: i2c1grp {
 			fsl,pins = <
 				MX6SL_PAD_I2C1_SCL__I2C1_SCL	0x4001b8b1
@@ -575,6 +584,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -584,10 +594,6 @@
 	vin-supply = <&sw2_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&sw2_reg>;
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-kobo-aura2.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-kobo-aura2.dts
new file mode 100644
index 000000000000..657d0f1b6115
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-kobo-aura2.dts
@@ -0,0 +1,555 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Kobo Aura 2 ebook reader
+ *
+ * Name on mainboard is: 37NB-E60QL0+4B1
+ * Serials start with: E60QL2
+ *
+ * Copyright 2022 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Kobo Aura 2";
+	compatible = "kobo,aura2", "fsl,imx6sl";
+
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led-0 {
+			label = "koboaura2:white:on";
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_WHITE>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	lm3630a: backlight@36 {
+		compatible = "ti,lm3630a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lm3630a_bl_gpio>;
+		reg = <0x36>;
+		enable-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0>;
+			label = "backlight";
+			default-brightness = <0>;
+			max-brightness = <255>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* eKTF2232 at 0x15 */
+	/* FP9928 at 0x48 */
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ricoh619: pmic@32 {
+		compatible = "ricoh,rc5t619";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ricoh_gpio>;
+		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		system-power-controller;
+
+		regulators {
+			dcdc1_reg: DCDC1 {
+				regulator-name = "DCDC1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <900000>;
+					regulator-suspend-min-microvolt = <900000>;
+				};
+			};
+
+			/* Core3_3V3 */
+			dcdc2_reg: DCDC2 {
+				regulator-name = "DCDC2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3100000>;
+					regulator-suspend-min-microvolt = <3100000>;
+				};
+			};
+
+			dcdc3_reg: DCDC3 {
+				regulator-name = "DCDC3";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V2 */
+			dcdc4_reg: DCDC4 {
+				regulator-name = "DCDC4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V8 */
+			dcdc5_reg: DCDC5 {
+				regulator-name = "DCDC5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1700000>;
+					regulator-suspend-min-microvolt = <1700000>;
+				};
+			};
+
+			/* IR_3V3 */
+			ldo1_reg: LDO1  {
+				regulator-name = "LDO1";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* Core1_3V3 */
+			ldo2_reg: LDO2  {
+				regulator-name = "LDO2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3000000>;
+					regulator-suspend-min-microvolt = <3000000>;
+				};
+			};
+
+			/* Core5_1V2 */
+			ldo3_reg: LDO3  {
+				regulator-name = "LDO3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-boot-on;
+			};
+
+			/* SPD_3V3 */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* DDR_0V6 */
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* VDD_PWM */
+			ldo7_reg: LDO7 {
+				regulator-name = "LDO7";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* ldo_1v8 */
+			ldo8_reg: LDO8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "LDO9";
+				regulator-boot-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "LDO10";
+				regulator-boot-on;
+			};
+
+			ldortc1_reg: LDORTC1  {
+				regulator-name = "LDORTC1";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_arm {
+	vin-supply = <&dcdc3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4, through-holes */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* TP198, next to J4, SMD pads */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	non-removable;
+	status = "okay";
+
+	/* internal uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * RTL8189F SDIO WiFi
+	 */
+};
+
+&usbotg1 {
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x17059
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x17059
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT6__GPIO5_IO07 0x17059
+		>;
+	};
+
+	pinctrl_lm3630a_bl_gpio: lm3630a-bl-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059 /* HWEN */
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CLK__GPIO5_IO15	0x1b8b1 /* ricoh619 chg */
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11	0x1b8b1 /* ricoh619 irq */
+			MX6SL_PAD_KEY_COL2__GPIO3_IO28	0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6sl-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6sl-pinfunc.h
index bcf16060ecdc..bcf16060ecdc 100644
--- a/arch/arm/boot/dts/imx6sl-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-pinfunc.h
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts
new file mode 100644
index 000000000000..815119c12bd4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts
@@ -0,0 +1,634 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Tolino Shine 2 HD ebook reader
+ *
+ * Name on mainboard is: 37NB-E60QF0+4A2 or 37NB-E60QF0+4A3
+ * Serials start with: E60QF2
+ *
+ * Copyright 2020 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Tolino Shine 2 HD";
+	compatible = "kobo,tolino-shine2hd", "fsl,imx6sl";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ec 0 50000>;
+		power-supply = <&backlight_regulator>;
+	};
+
+	backlight_regulator: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_power>;
+		regulator-name = "backlight";
+		gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-fl {
+			label = "Frontlight";
+			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BRIGHTNESS_CYCLE>;
+		};
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led-0 {
+			label = "tolinoshine2hd:white:on";
+			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-1 {
+			label = "tolinoshine2hd:white:backlightboost";
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "off";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	ec: embedded-controller@43 {
+		compatible = "netronix,ntxec";
+		reg = <0x43>;
+		#pwm-cells = <2>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	zforce: touchscreen@50 {
+		compatible = "neonode,zforce";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_zforce>;
+		reg = <0x50>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&ldo1_reg>;
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+		x-size = <1072>;
+		y-size = <1448>;
+	};
+
+	/* TODO: TPS65185 PMIC for E Ink at 0x68 */
+
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ricoh619: pmic@32 {
+		compatible = "ricoh,rc5t619";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ricoh_gpio>;
+		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+
+		regulators {
+			dcdc1_reg: DCDC1 {
+				regulator-name = "DCDC1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <900000>;
+					regulator-suspend-min-microvolt = <900000>;
+				};
+			};
+
+			/* Core3_3V3 */
+			dcdc2_reg: DCDC2 {
+				regulator-name = "DCDC2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3100000>;
+					regulator-suspend-min-microvolt = <3100000>;
+				};
+			};
+
+			dcdc3_reg: DCDC3 {
+				regulator-name = "DCDC3";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V2 */
+			dcdc4_reg: DCDC4 {
+				regulator-name = "DCDC4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V8 */
+			dcdc5_reg: DCDC5 {
+				regulator-name = "DCDC5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1700000>;
+					regulator-suspend-min-microvolt = <1700000>;
+				};
+			};
+
+			/* IR_3V3 */
+			ldo1_reg: LDO1  {
+				regulator-name = "LDO1";
+				regulator-boot-on;
+			};
+
+			/* Core1_3V3 */
+			ldo2_reg: LDO2  {
+				regulator-name = "LDO2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3000000>;
+					regulator-suspend-min-microvolt = <3000000>;
+				};
+			};
+
+			/* Core5_1V2 */
+			ldo3_reg: LDO3  {
+				regulator-name = "LDO3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-boot-on;
+			};
+
+			/* SPD_3V3 */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* DDR_0V6 */
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* VDD_PWM */
+			ldo7_reg: LDO7 {
+				regulator-name = "LDO7";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* ldo_1v8 */
+			ldo8_reg: LDO8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "LDO9";
+				regulator-boot-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "LDO10";
+				regulator-boot-on;
+			};
+
+			ldortc1_reg: LDORTC1  {
+				regulator-name = "LDORTC1";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_backlight_power: backlight-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x17059
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x17059
+			MX6SL_PAD_KEY_COL1__GPIO3_IO26  0x17059
+			MX6SL_PAD_KEY_ROW0__GPIO3_IO25  0x17059
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SL_PAD_LCD_DAT0__GPIO2_IO20	0x79
+			MX6SL_PAD_LCD_DAT1__GPIO2_IO21	0x79
+			MX6SL_PAD_LCD_DAT2__GPIO2_IO22	0x79
+			MX6SL_PAD_LCD_DAT3__GPIO2_IO23	0x79
+			MX6SL_PAD_LCD_DAT4__GPIO2_IO24	0x79
+			MX6SL_PAD_LCD_DAT5__GPIO2_IO25	0x79
+			MX6SL_PAD_LCD_DAT6__GPIO2_IO26	0x79
+			MX6SL_PAD_LCD_DAT7__GPIO2_IO27	0x79
+			MX6SL_PAD_LCD_DAT8__GPIO2_IO28	0x79
+			MX6SL_PAD_LCD_DAT9__GPIO2_IO29	0x79
+			MX6SL_PAD_LCD_DAT10__GPIO2_IO30	0x79
+			MX6SL_PAD_LCD_DAT11__GPIO2_IO31	0x79
+			MX6SL_PAD_LCD_DAT12__GPIO3_IO00	0x79
+			MX6SL_PAD_LCD_DAT13__GPIO3_IO01	0x79
+			MX6SL_PAD_LCD_DAT14__GPIO3_IO02	0x79
+			MX6SL_PAD_LCD_DAT15__GPIO3_IO03	0x79
+			MX6SL_PAD_LCD_DAT16__GPIO3_IO04	0x79
+			MX6SL_PAD_LCD_DAT17__GPIO3_IO05	0x79
+			MX6SL_PAD_LCD_DAT18__GPIO3_IO06	0x79
+			MX6SL_PAD_LCD_DAT19__GPIO3_IO07	0x79
+			MX6SL_PAD_LCD_DAT20__GPIO3_IO08	0x79
+			MX6SL_PAD_LCD_DAT21__GPIO3_IO09	0x79
+			MX6SL_PAD_LCD_DAT22__GPIO3_IO10	0x79
+			MX6SL_PAD_LCD_DAT23__GPIO3_IO11	0x79
+			MX6SL_PAD_LCD_CLK__GPIO2_IO15		0x79
+			MX6SL_PAD_LCD_ENABLE__GPIO2_IO16	0x79
+			MX6SL_PAD_LCD_HSYNC__GPIO2_IO17	0x79
+			MX6SL_PAD_LCD_VSYNC__GPIO2_IO18	0x79
+			MX6SL_PAD_LCD_RESET__GPIO2_IO19	0x79
+			MX6SL_PAD_KEY_COL3__GPIO3_IO30		0x79
+			MX6SL_PAD_KEY_ROW7__GPIO4_IO07		0x79
+			MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
+			MX6SL_PAD_KEY_COL5__GPIO4_IO02		0x79
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13    0x17059
+			MX6SL_PAD_EPDC_SDCE2__GPIO1_IO29  0x17059
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh_gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CLK__GPIO5_IO15	0x1b8b1 /* ricoh619 chg */
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11	0x1b8b1 /* ricoh619 irq */
+			MX6SL_PAD_KEY_COL2__GPIO3_IO28	0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+
+	pinctrl_zforce: zforcegrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06		0x17059 /* TP_INT */
+			MX6SL_PAD_SD1_DAT5__GPIO5_IO09		0x10059 /* TP_RST */
+		>;
+	};
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_arm {
+	vin-supply = <&dcdc3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4, through-holes */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* TP198, next to J4, SMD pads */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	non-removable;
+	status = "okay";
+
+	/* internal uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * 37NB-E60QF0+4A2: CyberTan WC121 (BCM43362) SDIO WiFi
+	 * 37NB-E60QF0+4A3: RTL8189F SDIO WiFi
+	 */
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine3.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine3.dts
new file mode 100644
index 000000000000..db5d8509935f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine3.dts
@@ -0,0 +1,340 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * Device tree for the Tolino Shine 3 ebook reader
+ *
+ * Name on mainboard is: 37NB-E60K00+4A4
+ * Serials start with: E60K02 (a number also seen in
+ * vendor kernel sources)
+ *
+ * This mainboard seems to be equipped with different SoCs.
+ * In the Toline Shine 3 ebook reader it is a i.MX6SL
+ *
+ * Copyright 2019 Andreas Kemnade
+ * based on works
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+#include "e60k02.dtsi"
+
+/ {
+	model = "Tolino Shine 3";
+	compatible = "kobo,tolino-shine3", "fsl,imx6sl";
+};
+
+&gpio_keys {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_keys>;
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06                0x17059 /* TP_INT */
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13                0x10059 /* TP_RST */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08	0x17059	/* PWR_SW */
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12	0x17059	/* HALL_EN */
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SL_PAD_LCD_DAT0__GPIO2_IO20	0x79
+			MX6SL_PAD_LCD_DAT1__GPIO2_IO21	0x79
+			MX6SL_PAD_LCD_DAT2__GPIO2_IO22	0x79
+			MX6SL_PAD_LCD_DAT3__GPIO2_IO23	0x79
+			MX6SL_PAD_LCD_DAT4__GPIO2_IO24	0x79
+			MX6SL_PAD_LCD_DAT5__GPIO2_IO25	0x79
+			MX6SL_PAD_LCD_DAT6__GPIO2_IO26	0x79
+			MX6SL_PAD_LCD_DAT7__GPIO2_IO27	0x79
+			MX6SL_PAD_LCD_DAT8__GPIO2_IO28	0x79
+			MX6SL_PAD_LCD_DAT9__GPIO2_IO29	0x79
+			MX6SL_PAD_LCD_DAT10__GPIO2_IO30	0x79
+			MX6SL_PAD_LCD_DAT11__GPIO2_IO31	0x79
+			MX6SL_PAD_LCD_DAT12__GPIO3_IO00	0x79
+			MX6SL_PAD_LCD_DAT13__GPIO3_IO01	0x79
+			MX6SL_PAD_LCD_DAT14__GPIO3_IO02	0x79
+			MX6SL_PAD_LCD_DAT15__GPIO3_IO03	0x79
+			MX6SL_PAD_LCD_DAT16__GPIO3_IO04	0x79
+			MX6SL_PAD_LCD_DAT17__GPIO3_IO05	0x79
+			MX6SL_PAD_LCD_DAT18__GPIO3_IO06	0x79
+			MX6SL_PAD_LCD_DAT19__GPIO3_IO07	0x79
+			MX6SL_PAD_LCD_DAT20__GPIO3_IO08	0x79
+			MX6SL_PAD_LCD_DAT21__GPIO3_IO09	0x79
+			MX6SL_PAD_LCD_DAT22__GPIO3_IO10	0x79
+			MX6SL_PAD_LCD_DAT23__GPIO3_IO11	0x79
+			MX6SL_PAD_LCD_CLK__GPIO2_IO15		0x79
+			MX6SL_PAD_LCD_ENABLE__GPIO2_IO16	0x79
+			MX6SL_PAD_LCD_HSYNC__GPIO2_IO17	0x79
+			MX6SL_PAD_LCD_VSYNC__GPIO2_IO18	0x79
+			MX6SL_PAD_LCD_RESET__GPIO2_IO19	0x79
+			MX6SL_PAD_KEY_COL3__GPIO3_IO30		0x79
+			MX6SL_PAD_KEY_ROW7__GPIO4_IO07		0x79
+			MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
+			MX6SL_PAD_KEY_COL5__GPIO4_IO02		0x79
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT6__GPIO5_IO07 0x17059
+		>;
+	};
+
+	pinctrl_lm3630a_bl_gpio: lm3630a-bl-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10		0x10059 /* HWEN */
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh_gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CLK__GPIO5_IO15                  0x1b8b1 /* ricoh619 chg */
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11        0x1b8b1 /* ricoh619 irq */
+			MX6SL_PAD_KEY_COL2__GPIO3_IO28                         0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
+
+&leds {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_led>;
+};
+
+&lm3630a {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lm3630a_bl_gpio>;
+};
+
+&reg_wifi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wifi_power>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&ricoh619 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ricoh_gpio>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+};
+
+&wifi_pwrseq {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wifi_reset>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision.dts
new file mode 100644
index 000000000000..2694fe18a91b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision.dts
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Tolino Vison ebook reader
+ *
+ * Name on mainboard is: 37NB-E60Q30+4A3
+ * Serials start with: 6032
+ *
+ * Copyright 2023 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Tolino Vision";
+	compatible = "kobo,tolino-vision", "fsl,imx6sl";
+
+	aliases {
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ec 0 50000>;
+		power-supply = <&backlight_regulator>;
+	};
+
+	backlight_regulator: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_power>;
+		regulator-name = "backlight";
+		gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			/* magnetic sensor in the corner next to the uSD slot */
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-fl {
+			label = "Frontlight";
+			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BRIGHTNESS_CYCLE>;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			/* LED on home button */
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* LED on power button */
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	touchscreen@15 {
+		compatible = "elan,ektf2132";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ts>;
+		power-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&gpio5 6 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	accelerometer@1d {
+		compatible = "fsl,mma8652";
+		reg = <0x1d>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	ec: embedded-controller@43 {
+		compatible = "netronix,ntxec";
+		reg = <0x43>;
+		#pwm-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ec>;
+		interrupts-extended = <&gpio5 11 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+	};
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* J9 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	cd-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	/* removable uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/* CyberTan WC121 (BCM43362) SDIO WiFi */
+};
+
+&usdhc4 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc4_sleep>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	status = "okay";
+
+	/* internal eMMC */
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_backlight_power: backlight-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059
+		>;
+	};
+
+	pinctrl_ec: ecgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11  0x17000
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x110B0
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x110B0
+			MX6SL_PAD_KEY_COL1__GPIO3_IO26  0x11030
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT6__GPIO5_IO07    0x17059
+			MX6SL_PAD_SD1_DAT7__GPIO5_IO10    0x17059
+			MX6SL_PAD_EPDC_SDCE2__GPIO1_IO29  0x17059
+		>;
+	};
+
+	pinctrl_ts: tsgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13	0x110B0
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06	0x1B0B1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6SL_PAD_SD2_DAT4__GPIO5_IO02		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x17059
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x13059
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x17059
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x17059
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x17059
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x17059
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x17059
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x17059
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x17059
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x17059
+			MX6SL_PAD_FEC_REF_CLK__SD4_RESET	0x17068
+		>;
+	};
+
+	pinctrl_usdhc4_100mhz: usdhc4-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x170b9
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x130b9
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x170b9
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x170b9
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x170b9
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x170b9
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x170b9
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x170b9
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x170b9
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc4_200mhz: usdhc4-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x170f9
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x130f9
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x170f9
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x170f9
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x170f9
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x170f9
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x170f9
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x170f9
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x170f9
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc4_sleep: usdhc4-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__GPIO4_IO21	0x100c1
+			MX6SL_PAD_FEC_MDIO__GPIO4_IO20		0x100c1
+			MX6SL_PAD_FEC_RX_ER__GPIO4_IO19		0x100c1
+			MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25	0x100c1
+			MX6SL_PAD_FEC_RXD1__GPIO4_IO18		0x100c1
+			MX6SL_PAD_FEC_TXD0__GPIO4_IO24		0x100c1
+			MX6SL_PAD_FEC_MDC__GPIO4_IO23		0x100c1
+			MX6SL_PAD_FEC_RXD0__GPIO4_IO17		0x100c1
+			MX6SL_PAD_FEC_TX_EN__GPIO4_IO22		0x100c1
+			MX6SL_PAD_FEC_TXD1__GPIO4_IO16		0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision5.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision5.dts
new file mode 100644
index 000000000000..6bc342035e2b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision5.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * Device tree for the Tolino Vision 5 ebook reader
+ *
+ * Name on mainboard is: 37NB-E70K0M+6A3
+ * Serials start with: E70K02 (a number also seen in
+ * vendor kernel sources)
+ *
+ * This mainboard seems to be equipped with different SoCs.
+ * In the Tolino Vision 5 ebook reader it is a i.MX6SL
+ *
+ * Copyright 2021 Andreas Kemnade
+ * based on works
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+#include "e70k02.dtsi"
+
+/ {
+	model = "Tolino Vision 5";
+	compatible = "kobo,tolino-vision5", "fsl,imx6sl";
+};
+
+&gpio_keys {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_keys>;
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TXD0__GPIO4_IO24          0x17059 /* TP_INT */
+			MX6SL_PAD_FEC_RXD1__GPIO4_IO18          0x10059 /* TP_RST */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25	0x17059	/* PWR_SW */
+			MX6SL_PAD_FEC_MDC__GPIO4_IO23	0x17059	/* HALL_EN */
+			MX6SL_PAD_KEY_COL4__GPIO4_IO00		0x17059	/* PAGE_UP */
+			MX6SL_PAD_KEY_COL5__GPIO4_IO02		0x17059	/* PAGE_DOWN */
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SL_PAD_LCD_DAT1__GPIO2_IO21	0x79
+			MX6SL_PAD_LCD_DAT4__GPIO2_IO24	0x79
+			MX6SL_PAD_LCD_DAT5__GPIO2_IO25	0x79
+			MX6SL_PAD_LCD_DAT6__GPIO2_IO26	0x79
+			MX6SL_PAD_LCD_DAT7__GPIO2_IO27	0x79
+			MX6SL_PAD_LCD_DAT8__GPIO2_IO28	0x79
+			MX6SL_PAD_LCD_DAT9__GPIO2_IO29	0x79
+			MX6SL_PAD_LCD_DAT10__GPIO2_IO30	0x79
+			MX6SL_PAD_LCD_DAT11__GPIO2_IO31	0x79
+			MX6SL_PAD_LCD_DAT12__GPIO3_IO00	0x79
+			MX6SL_PAD_LCD_DAT13__GPIO3_IO01	0x79
+			MX6SL_PAD_LCD_DAT14__GPIO3_IO02	0x79
+			MX6SL_PAD_LCD_DAT15__GPIO3_IO03	0x79
+			MX6SL_PAD_LCD_DAT16__GPIO3_IO04	0x79
+			MX6SL_PAD_LCD_DAT17__GPIO3_IO05	0x79
+			MX6SL_PAD_LCD_DAT18__GPIO3_IO06	0x79
+			MX6SL_PAD_LCD_DAT19__GPIO3_IO07	0x79
+			MX6SL_PAD_LCD_DAT20__GPIO3_IO08	0x79
+			MX6SL_PAD_LCD_DAT21__GPIO3_IO09	0x79
+			MX6SL_PAD_LCD_DAT22__GPIO3_IO10	0x79
+			MX6SL_PAD_LCD_DAT23__GPIO3_IO11	0x79
+			MX6SL_PAD_LCD_CLK__GPIO2_IO15		0x79
+			MX6SL_PAD_LCD_ENABLE__GPIO2_IO16	0x79
+			MX6SL_PAD_LCD_HSYNC__GPIO2_IO17	0x79
+			MX6SL_PAD_LCD_VSYNC__GPIO2_IO18	0x79
+			MX6SL_PAD_LCD_RESET__GPIO2_IO19	0x79
+			MX6SL_PAD_FEC_TX_CLK__GPIO4_IO21	0x79
+			MX6SL_PAD_FEC_REF_CLK__GPIO4_IO26	0x79
+			MX6SL_PAD_KEY_COL3__GPIO3_IO30		0x79
+			MX6SL_PAD_KEY_ROW7__GPIO4_IO07		0x79
+			MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_RXD0__GPIO4_IO17	0x10059
+		>;
+	};
+
+	pinctrl_lm3630a_bl_gpio: lm3630a-bl-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10		0x10059 /* HWEN */
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_MDIO__GPIO4_IO20		0x1b8b1 /* ricoh619 chg */
+			MX6SL_PAD_FEC_RX_ER__GPIO4_IO19		0x1b8b1 /* ricoh619 irq */
+			MX6SL_PAD_KEY_COL2__GPIO3_IO28		0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD	0x17059
+			MX6SL_PAD_SD1_CLK__SD1_CLK	0x17059
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0	0x17059
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1	0x17059
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2	0x17059
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3	0x17059
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4	0x17059
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5	0x17059
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6	0x17059
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD	0x170b9
+			MX6SL_PAD_SD1_CLK__SD1_CLK	0x170b9
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0	0x170b9
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1	0x170b9
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2	0x170b9
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3	0x170b9
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4	0x170b9
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5	0x170b9
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6	0x170b9
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD	0x170f9
+			MX6SL_PAD_SD1_CLK__SD1_CLK	0x170f9
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0	0x170f9
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1	0x170f9
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2	0x170f9
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3	0x170f9
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4	0x170b9
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5	0x170b9
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6	0x170b9
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_sleep: usdhc1-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD	0x10059
+			MX6SL_PAD_SD1_CLK__SD1_CLK	0x10059
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0	0x10059
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1	0x10059
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2	0x10059
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3	0x10059
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4	0x10059
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5	0x10059
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6	0x10059
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7	0x10059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	 /* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
+
+&leds {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_led>;
+};
+
+&lm3630a {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lm3630a_bl_gpio>;
+};
+
+&reg_wifi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wifi_power>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_arm {
+	vin-supply = <&dcdc3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&ricoh619 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ricoh_gpio>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep>;
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+};
+
+&wifi_pwrseq {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wifi_reset>;
+};
diff --git a/arch/arm/boot/dts/imx6sl-warp.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-warp.dts
index 408da704c459..9d7c8884892a 100644
--- a/arch/arm/boot/dts/imx6sl-warp.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-warp.dts
@@ -51,8 +51,8 @@
 #include "imx6sl.dtsi"
 
 / {
-	model = "WaRP Board";
-	compatible = "warp,imx6sl-warp", "fsl,imx6sl";
+	model = "Revotics WaRP Board";
+	compatible = "revotics,imx6sl-warp", "fsl,imx6sl";
 
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
index 59c54e6ad09a..28111efb19a6 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
@@ -39,6 +39,9 @@
 		spi1 = &ecspi2;
 		spi2 = &ecspi3;
 		spi3 = &ecspi4;
+		usb0 = &usbotg1;
+		usb1 = &usbotg2;
+		usb2 = &usbh;
 		usbphy0 = &usbphy1;
 		usbphy1 = &usbphy2;
 	};
@@ -47,23 +50,21 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0x0>;
 			next-level-cache = <&L2>;
-			operating-points = <
+			operating-points =
 				/* kHz    uV */
-				996000  1275000
-				792000  1175000
-				396000  975000
-			>;
-			fsl,soc-operating-points = <
-				/* ARM kHz      SOC-PU uV */
-				996000          1225000
-				792000          1175000
-				396000          1175000
-			>;
+				<996000  1275000>,
+				<792000  1175000>,
+				<396000  975000>;
+			fsl,soc-operating-points =
+				/* ARM kHz	SOC-PU uV */
+				<996000		1225000>,
+				<792000		1175000>,
+				<396000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SL_CLK_ARM>, <&clks IMX6SL_CLK_PLL2_PFD2>,
@@ -74,6 +75,8 @@
 			arm-supply = <&reg_arm>;
 			pu-supply = <&reg_pu>;
 			soc-supply = <&reg_soc>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 	};
 
@@ -91,15 +94,6 @@
 		};
 	};
 
-	tempmon: tempmon {
-		compatible = "fsl,imx6q-tempmon";
-		interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-parent = <&gpc>;
-		fsl,tempmon = <&anatop>;
-		fsl,tempmon-data = <&ocotp>;
-		clocks = <&clks IMX6SL_CLK_PLL3_USB_OTG>;
-	};
-
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
 		interrupt-parent = <&gpc>;
@@ -121,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
@@ -133,7 +130,7 @@
 			interrupt-parent = <&intc>;
 		};
 
-		L2: l2-cache@a02000 {
+		L2: cache-controller@a02000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x00a02000 0x1000>;
 			interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>;
@@ -143,7 +140,7 @@
 			arm,data-latency = <4 2 3>;
 		};
 
-		aips1: aips-bus@2000000 {
+		aips1: bus@2000000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -228,7 +225,7 @@
 
 				uart5: serial@2018000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02018000 0x4000>;
 					interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -241,7 +238,7 @@
 
 				uart1: serial@2020000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -254,7 +251,7 @@
 
 				uart2: serial@2024000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02024000 0x4000>;
 					interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -315,7 +312,7 @@
 
 				uart3: serial@2034000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02034000 0x4000>;
 					interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -328,7 +325,7 @@
 
 				uart4: serial@2038000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02038000 0x4000>;
 					interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -341,7 +338,7 @@
 			};
 
 			pwm1: pwm@2080000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
 				reg = <0x02080000 0x4000>;
 				interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>;
@@ -351,7 +348,7 @@
 			};
 
 			pwm2: pwm@2084000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
 				reg = <0x02084000 0x4000>;
 				interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
@@ -361,7 +358,7 @@
 			};
 
 			pwm3: pwm@2088000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
 				reg = <0x02088000 0x4000>;
 				interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
@@ -371,7 +368,7 @@
 			};
 
 			pwm4: pwm@208c000 {
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
 				reg = <0x0208c000 0x4000>;
 				interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
@@ -380,7 +377,7 @@
 				clock-names = "ipg", "per";
 			};
 
-			gpt: gpt@2098000 {
+			gpt: timer@2098000 {
 				compatible = "fsl,imx6sl-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -491,7 +488,7 @@
 					      <&iomuxc 21 161 1>;
 			};
 
-			kpp: kpp@20b8000 {
+			kpp: keypad@20b8000 {
 				compatible = "fsl,imx6sl-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -499,14 +496,14 @@
 				status = "disabled";
 			};
 
-			wdog1: wdog@20bc000 {
+			wdog1: watchdog@20bc000 {
 				compatible = "fsl,imx6sl-wdt", "fsl,imx21-wdt";
 				reg = <0x020bc000 0x4000>;
 				interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_IPG>;
 			};
 
-			wdog2: wdog@20c0000 {
+			wdog2: watchdog@20c0000 {
 				compatible = "fsl,imx6sl-wdt", "fsl,imx21-wdt";
 				reg = <0x020c0000 0x4000>;
 				interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>;
@@ -514,7 +511,7 @@
 				status = "disabled";
 			};
 
-			clks: ccm@20c4000 {
+			clks: clock-controller@20c4000 {
 				compatible = "fsl,imx6sl-ccm";
 				reg = <0x020c4000 0x4000>;
 				interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>,
@@ -625,6 +622,16 @@
 					anatop-min-voltage = <725000>;
 					anatop-max-voltage = <1450000>;
 				};
+
+				tempmon: tempmon {
+					compatible = "fsl,imx6q-tempmon";
+					interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-parent = <&gpc>;
+					fsl,tempmon = <&anatop>;
+					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+					nvmem-cell-names = "calib", "temp_grade";
+					clocks = <&clks IMX6SL_CLK_PLL3_USB_OTG>;
+				};
 			};
 
 			usbphy1: usbphy@20c9000 {
@@ -675,7 +682,7 @@
 				interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6sl-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -707,7 +714,7 @@
 						#power-domain-cells = <0>;
 						power-supply = <&reg_pu>;
 						clocks = <&clks IMX6SL_CLK_GPU2D_OVG>,
-						         <&clks IMX6SL_CLK_GPU2D_PODF>;
+							 <&clks IMX6SL_CLK_GPU2D_PODF>;
 					};
 
 					pd_disp: power-domain@2 {
@@ -728,7 +735,7 @@
 				reg = <0x020e0000 0x38>;
 			};
 
-			iomuxc: iomuxc@20e0000 {
+			iomuxc: pinctrl@20e0000 {
 				compatible = "fsl,imx6sl-iomuxc";
 				reg = <0x020e0000 0x4000>;
 			};
@@ -743,7 +750,7 @@
 				interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sl-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -777,7 +784,7 @@
 				power-domains = <&pd_disp>;
 			};
 
-			dcp: dcp@20fc000 {
+			dcp: crypto@20fc000 {
 				compatible = "fsl,imx6sl-dcp", "fsl,imx28-dcp";
 				reg = <0x020fc000 0x4000>;
 				interrupts = <0 99 IRQ_TYPE_LEVEL_HIGH>,
@@ -786,7 +793,7 @@
 			};
 		};
 
-		aips2: aips-bus@2100000 {
+		aips2: bus@2100000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -851,7 +858,7 @@
 				status = "disabled";
 			};
 
-			usdhc1: usdhc@2190000 {
+			usdhc1: mmc@2190000 {
 				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -863,7 +870,7 @@
 				status = "disabled";
 			};
 
-			usdhc2: usdhc@2194000 {
+			usdhc2: mmc@2194000 {
 				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -875,7 +882,7 @@
 				status = "disabled";
 			};
 
-			usdhc3: usdhc@2198000 {
+			usdhc3: mmc@2198000 {
 				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
 				reg = <0x02198000 0x4000>;
 				interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
@@ -887,7 +894,7 @@
 				status = "disabled";
 			};
 
-			usdhc4: usdhc@219c000 {
+			usdhc4: mmc@219c000 {
 				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
 				reg = <0x0219c000 0x4000>;
 				interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
@@ -936,8 +943,10 @@
 			};
 
 			rngb: rngb@21b4000 {
+				compatible = "fsl,imx6sl-rngb", "fsl,imx25-rngb";
 				reg = <0x021b4000 0x4000>;
 				interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6SL_CLK_DUMMY>;
 			};
 
 			weim: weim@21b8000 {
@@ -949,10 +958,24 @@
 				status = "disabled";
 			};
 
-			ocotp: ocotp@21bc000 {
+			ocotp: efuse@21bc000 {
 				compatible = "fsl,imx6sl-ocotp", "syscon";
 				reg = <0x021bc000 0x4000>;
 				clocks = <&clks IMX6SL_CLK_OCOTP>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
+
+				tempmon_calib: calib@38 {
+					reg = <0x38 4>;
+				};
+
+				tempmon_temp_grade: temp-grade@20 {
+					reg = <0x20 4>;
+				};
 			};
 
 			audmux: audmux@21d8000 {
diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
index 3e1d32fdf4b8..e3e9b0ec4f73 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
@@ -37,7 +37,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -109,6 +109,14 @@
 		enable-active-high;
 	};
 
+	reg_sd2_vmmc: regulator-sd2-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "eMMC-VCCQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+	};
+
 	reg_sd3_vmmc: regulator-sd3-vmmc {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -132,6 +140,31 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
+		model = "wm8962-audio";
+		audio-cpu = <&ssi2>;
+		audio-codec = <&wm8962>;
+		audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Ext Spk", "SPKOUTL",
+			"Ext Spk", "SPKOUTR",
+			"AMIC", "MICBIAS",
+			"IN3R", "AMIC";
+		mux-int-port = <2>;
+		mux-ext-port = <3>;
+		hp-det-gpio = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux3>;
+	status = "okay";
 };
 
 &cpu0 {
@@ -247,6 +280,27 @@
 	};
 };
 
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	wm8962: audio-codec@1a {
+		compatible = "wlf,wm8962";
+		reg = <0x1a>;
+		clocks = <&clks IMX6SLL_CLK_EXTERN_AUDIO>;
+		DCVDD-supply = <&vgen3_reg>;
+		DBVDD-supply = <&reg_aud3v>;
+		AVDD-supply = <&vgen3_reg>;
+		CPVDD-supply = <&vgen3_reg>;
+		MICVDD-supply = <&reg_aud3v>;
+		PLLVDD-supply = <&vgen3_reg>;
+		SPKVDD1-supply = <&reg_aud4v>;
+		SPKVDD2-supply = <&reg_aud4v>;
+	};
+};
+
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcd>;
@@ -260,15 +314,12 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
-&reg_3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &snvs_poweroff {
 	status = "okay";
 };
@@ -277,6 +328,10 @@
 	status = "okay";
 };
 
+&ssi2 {
+	status = "okay";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -296,6 +351,17 @@
 	status = "okay";
 };
 
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	vqmmc-supply = <&reg_sd2_vmmc>;
+	status = "okay";
+};
+
 &usbotg1 {
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	pinctrl-names = "default";
@@ -333,6 +399,22 @@
 };
 
 &iomuxc {
+	pinctrl_audmux3: audmux3grp {
+		fsl,pins = <
+			MX6SLL_PAD_AUD_TXC__AUD3_TXC		0x4130b0
+			MX6SLL_PAD_AUD_TXFS__AUD3_TXFS		0x4130b0
+			MX6SLL_PAD_AUD_TXD__AUD3_TXD		0x4110b0
+			MX6SLL_PAD_AUD_RXD__AUD3_RXD		0x4130b0
+			MX6SLL_PAD_AUD_MCLK__AUDIO_CLK_OUT	0x4130b0
+		>;
+	};
+
+	pinctrl_hp: hpgrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24 0x17059 /* HP DETECT */
+		>;
+	};
+
 	pinctrl_reg_sd3_vmmc: sd3vmmcgrp {
 		fsl,pins = <
 			MX6SLL_PAD_KEY_COL6__GPIO4_IO04 0x17059
@@ -381,7 +463,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1grp-100mhz {
 		fsl,pins = <
 			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x170b9
 			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x130b9
@@ -392,7 +474,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1grp-200mhz {
 		fsl,pins = <
 			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x170f9
 			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x130f9
@@ -403,6 +485,54 @@
 		>;
 	};
 
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x17059
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x17059
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x17059
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x17059
+			MX6SLL_PAD_SD2_DATA4__SD2_DATA4		0x17059
+			MX6SLL_PAD_SD2_DATA5__SD2_DATA5		0x17059
+			MX6SLL_PAD_SD2_DATA6__SD2_DATA6		0x17059
+			MX6SLL_PAD_SD2_DATA7__SD2_DATA7		0x17059
+			MX6SLL_PAD_GPIO4_IO21__SD2_STROBE	0x13059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x170b9
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x170b9
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x170b9
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x170b9
+			MX6SLL_PAD_SD2_DATA4__SD2_DATA4		0x170b9
+			MX6SLL_PAD_SD2_DATA5__SD2_DATA5		0x170b9
+			MX6SLL_PAD_SD2_DATA6__SD2_DATA6		0x170b9
+			MX6SLL_PAD_SD2_DATA7__SD2_DATA7		0x170b9
+			MX6SLL_PAD_GPIO4_IO21__SD2_STROBE	0x130b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x170f9
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x170f9
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x170f9
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x170f9
+			MX6SLL_PAD_SD2_DATA4__SD2_DATA4		0x170f9
+			MX6SLL_PAD_SD2_DATA5__SD2_DATA5		0x170f9
+			MX6SLL_PAD_SD2_DATA6__SD2_DATA6		0x170f9
+			MX6SLL_PAD_SD2_DATA7__SD2_DATA7		0x170f9
+			MX6SLL_PAD_GPIO4_IO21__SD2_STROBE	0x130f9
+		>;
+	};
+
 	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <
 			MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
@@ -421,7 +551,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__SD3_CMD		0x170a1
 			MX6SLL_PAD_SD3_CLK__SD3_CLK		0x130a1
@@ -433,7 +563,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__SD3_CMD		0x170e9
 			MX6SLL_PAD_SD3_CLK__SD3_CLK		0x130f9
@@ -452,6 +582,13 @@
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SLL_PAD_AUD_RXFS__I2C3_SCL  0x4041b8b1
+			MX6SLL_PAD_AUD_RXC__I2C3_SDA   0x4041b8b1
+		>;
+	};
+
 	pinctrl_lcd: lcdgrp {
 		fsl,pins = <
 			MX6SLL_PAD_LCD_DATA00__LCD_DATA00	0x79
diff --git a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clarahd.dts
index 7214d1c98249..c7cfe0b70f04 100644
--- a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clarahd.dts
@@ -62,6 +62,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD1_DATA3__GPIO5_IO06                0x17059 /* TP_INT */
+			MX6SLL_PAD_SD1_DATA2__GPIO5_IO13                0x10059 /* TP_RST */
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio-keysgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD1_DATA1__GPIO5_IO08	0x17059	/* PWR_SW */
@@ -104,7 +111,6 @@
 			MX6SLL_PAD_KEY_ROW7__GPIO4_IO07		0x79
 			MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
 			MX6SLL_PAD_KEY_COL5__GPIO4_IO02		0x79
-			MX6SLL_PAD_KEY_ROW6__GPIO4_IO05		0x79
 		>;
 	};
 
@@ -170,6 +176,13 @@
 		>;
 	};
 
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SLL_PAD_KEY_ROW6__UART4_DCE_TX 0x1b0b1
+			MX6SLL_PAD_KEY_COL6__UART4_DCE_RX 0x1b0b1
+		>;
+	};
+
 	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <
 			MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
@@ -302,6 +315,11 @@
 	pinctrl-0 = <&pinctrl_uart1>;
 };
 
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
 	pinctrl-0 = <&pinctrl_usdhc2>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-librah2o.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-librah2o.dts
new file mode 100644
index 000000000000..7e4f38dd11e2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-librah2o.dts
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * Device tree for the Kobo Libra H2O ebook reader
+ *
+ * Name on mainboard is: 37NB-E70K0M+6A3
+ * Serials start with: E70K02 (a number also seen in
+ * vendor kernel sources)
+ *
+ * This mainboard seems to be equipped with different SoCs.
+ * In the Kobo Libra H2O ebook reader it is an i.MX6SLL
+ *
+ * Copyright 2021 Andreas Kemnade
+ * based on works
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sll.dtsi"
+#include "e70k02.dtsi"
+
+/ {
+	model = "Kobo Libra H2O";
+	compatible = "kobo,librah2o", "fsl,imx6sll";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6SLL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <393216000>;
+};
+
+&cpu0 {
+	arm-supply = <&dcdc3_reg>;
+	soc-supply = <&dcdc1_reg>;
+};
+
+&gpio_keys {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_keys>;
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24	0x17059 /* TP_INT */
+			MX6SLL_PAD_GPIO4_IO18__GPIO4_IO18	0x10059 /* TP_RST */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO25__GPIO4_IO25	0x17059	/* PWR_SW */
+			MX6SLL_PAD_GPIO4_IO23__GPIO4_IO23	0x17059	/* HALL_EN */
+			MX6SLL_PAD_KEY_COL4__GPIO4_IO00		0x17059	/* PAGE_UP */
+			MX6SLL_PAD_KEY_COL5__GPIO4_IO02		0x17059	/* PAGE_DOWN */
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SLL_PAD_LCD_DATA01__GPIO2_IO21	0x79
+			MX6SLL_PAD_LCD_DATA04__GPIO2_IO24	0x79
+			MX6SLL_PAD_LCD_DATA05__GPIO2_IO25	0x79
+			MX6SLL_PAD_LCD_DATA06__GPIO2_IO26	0x79
+			MX6SLL_PAD_LCD_DATA07__GPIO2_IO27	0x79
+			MX6SLL_PAD_LCD_DATA08__GPIO2_IO28	0x79
+			MX6SLL_PAD_LCD_DATA09__GPIO2_IO29	0x79
+			MX6SLL_PAD_LCD_DATA10__GPIO2_IO30	0x79
+			MX6SLL_PAD_LCD_DATA11__GPIO2_IO31	0x79
+			MX6SLL_PAD_LCD_DATA12__GPIO3_IO00	0x79
+			MX6SLL_PAD_LCD_DATA13__GPIO3_IO01	0x79
+			MX6SLL_PAD_LCD_DATA14__GPIO3_IO02	0x79
+			MX6SLL_PAD_LCD_DATA15__GPIO3_IO03	0x79
+			MX6SLL_PAD_LCD_DATA16__GPIO3_IO04	0x79
+			MX6SLL_PAD_LCD_DATA17__GPIO3_IO05	0x79
+			MX6SLL_PAD_LCD_DATA18__GPIO3_IO06	0x79
+			MX6SLL_PAD_LCD_DATA19__GPIO3_IO07	0x79
+			MX6SLL_PAD_LCD_DATA20__GPIO3_IO08	0x79
+			MX6SLL_PAD_LCD_DATA21__GPIO3_IO09	0x79
+			MX6SLL_PAD_LCD_DATA22__GPIO3_IO10	0x79
+			MX6SLL_PAD_LCD_DATA23__GPIO3_IO11	0x79
+			MX6SLL_PAD_LCD_CLK__GPIO2_IO15		0x79
+			MX6SLL_PAD_LCD_ENABLE__GPIO2_IO16	0x79
+			MX6SLL_PAD_LCD_HSYNC__GPIO2_IO17	0x79
+			MX6SLL_PAD_LCD_VSYNC__GPIO2_IO18	0x79
+			MX6SLL_PAD_LCD_RESET__GPIO2_IO19	0x79
+			MX6SLL_PAD_GPIO4_IO21__GPIO4_IO21	0x79
+			MX6SLL_PAD_GPIO4_IO26__GPIO4_IO26	0x79
+			MX6SLL_PAD_KEY_COL3__GPIO3_IO30		0x79
+			MX6SLL_PAD_KEY_ROW7__GPIO4_IO07		0x79
+			MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SLL_PAD_I2C1_SCL__I2C1_SCL   0x4001f8b1
+			MX6SLL_PAD_I2C1_SDA__I2C1_SDA   0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1grp-sleep {
+		fsl,pins = <
+			MX6SLL_PAD_I2C1_SCL__I2C1_SCL   0x400108b1
+			MX6SLL_PAD_I2C1_SDA__I2C1_SDA   0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SLL_PAD_I2C2_SCL__I2C2_SCL   0x4001f8b1
+			MX6SLL_PAD_I2C2_SDA__I2C2_SDA   0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2grp-sleep {
+		fsl,pins = <
+			MX6SLL_PAD_I2C2_SCL__I2C2_SCL   0x400108b1
+			MX6SLL_PAD_I2C2_SDA__I2C2_SDA   0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SLL_PAD_REF_CLK_24M__I2C3_SCL 0x4001f8b1
+			MX6SLL_PAD_REF_CLK_32K__I2C3_SDA 0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO17__GPIO4_IO17	0x10059
+		>;
+	};
+
+	pinctrl_lm3630a_bl_gpio: lm3630a-bl-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_EPDC_PWR_CTRL3__GPIO2_IO10   0x10059 /* HWEN */
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO20__GPIO4_IO20	0x1b8b1 /* ricoh619 chg */
+			MX6SLL_PAD_GPIO4_IO19__GPIO4_IO19	0x1b8b1 /* ricoh619 irq */
+			MX6SLL_PAD_KEY_COL2__GPIO3_IO28		0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SLL_PAD_UART1_TXD__UART1_DCE_TX 0x1b0b1
+			MX6SLL_PAD_UART1_RXD__UART1_DCE_RX 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x17059
+			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x17059
+			MX6SLL_PAD_SD1_DATA0__SD1_DATA0	0x17059
+			MX6SLL_PAD_SD1_DATA1__SD1_DATA1	0x17059
+			MX6SLL_PAD_SD1_DATA2__SD1_DATA2	0x17059
+			MX6SLL_PAD_SD1_DATA3__SD1_DATA3	0x17059
+			MX6SLL_PAD_SD1_DATA4__SD1_DATA4	0x17059
+			MX6SLL_PAD_SD1_DATA5__SD1_DATA5	0x17059
+			MX6SLL_PAD_SD1_DATA6__SD1_DATA6	0x17059
+			MX6SLL_PAD_SD1_DATA7__SD1_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x170b9
+			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x170b9
+			MX6SLL_PAD_SD1_DATA0__SD1_DATA0	0x170b9
+			MX6SLL_PAD_SD1_DATA1__SD1_DATA1	0x170b9
+			MX6SLL_PAD_SD1_DATA2__SD1_DATA2	0x170b9
+			MX6SLL_PAD_SD1_DATA3__SD1_DATA3	0x170b9
+			MX6SLL_PAD_SD1_DATA4__SD1_DATA4	0x170b9
+			MX6SLL_PAD_SD1_DATA5__SD1_DATA5	0x170b9
+			MX6SLL_PAD_SD1_DATA6__SD1_DATA6	0x170b9
+			MX6SLL_PAD_SD1_DATA7__SD1_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x170f9
+			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x170f9
+			MX6SLL_PAD_SD1_DATA0__SD1_DATA0	0x170f9
+			MX6SLL_PAD_SD1_DATA1__SD1_DATA1	0x170f9
+			MX6SLL_PAD_SD1_DATA2__SD1_DATA2	0x170f9
+			MX6SLL_PAD_SD1_DATA3__SD1_DATA3	0x170f9
+			MX6SLL_PAD_SD1_DATA4__SD1_DATA4	0x170b9
+			MX6SLL_PAD_SD1_DATA5__SD1_DATA5	0x170b9
+			MX6SLL_PAD_SD1_DATA6__SD1_DATA6	0x170b9
+			MX6SLL_PAD_SD1_DATA7__SD1_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_sleep: usdhc1-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x10059
+			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x10059
+			MX6SLL_PAD_SD1_DATA0__SD1_DATA0	0x10059
+			MX6SLL_PAD_SD1_DATA1__SD1_DATA1	0x10059
+			MX6SLL_PAD_SD1_DATA2__SD1_DATA2	0x10059
+			MX6SLL_PAD_SD1_DATA3__SD1_DATA3	0x10059
+			MX6SLL_PAD_SD1_DATA4__SD1_DATA4	0x10059
+			MX6SLL_PAD_SD1_DATA5__SD1_DATA5	0x10059
+			MX6SLL_PAD_SD1_DATA6__SD1_DATA6	0x10059
+			MX6SLL_PAD_SD1_DATA7__SD1_DATA7	0x10059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SLL_PAD_SD3_DATA0__SD3_DATA0	0x11059
+			MX6SLL_PAD_SD3_DATA1__SD3_DATA1	0x11059
+			MX6SLL_PAD_SD3_DATA2__SD3_DATA2	0x11059
+			MX6SLL_PAD_SD3_DATA3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SLL_PAD_SD3_DATA0__SD3_DATA0	0x170b9
+			MX6SLL_PAD_SD3_DATA1__SD3_DATA1	0x170b9
+			MX6SLL_PAD_SD3_DATA2__SD3_DATA2	0x170b9
+			MX6SLL_PAD_SD3_DATA3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SLL_PAD_SD3_DATA0__SD3_DATA0	0x170f9
+			MX6SLL_PAD_SD3_DATA1__SD3_DATA1	0x170f9
+			MX6SLL_PAD_SD3_DATA2__SD3_DATA2	0x170f9
+			MX6SLL_PAD_SD3_DATA3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SLL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SLL_PAD_SD3_DATA0__GPIO5_IO19	0x100c1
+			MX6SLL_PAD_SD3_DATA1__GPIO5_IO20	0x100c1
+			MX6SLL_PAD_SD3_DATA2__GPIO5_IO16	0x100c1
+			MX6SLL_PAD_SD3_DATA3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_DATA6__GPIO4_IO29	0x10059	 /* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_DATA7__GPIO5_IO00	0x10059	 /* WIFI_RST */
+		>;
+	};
+};
+
+&leds {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_led>;
+};
+
+&lm3630a {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lm3630a_bl_gpio>;
+};
+
+&reg_wifi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wifi_power>;
+};
+
+&ricoh619 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ricoh_gpio>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep>;
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+};
+
+&wifi_pwrseq {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wifi_reset>;
+};
diff --git a/arch/arm/boot/dts/imx6sll-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6sll-pinfunc.h
index 713a346f4c89..713a346f4c89 100644
--- a/arch/arm/boot/dts/imx6sll-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sll.dtsi
index 85aa8bb98528..3659fd5ecfa6 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll.dtsi
@@ -36,6 +36,8 @@
 		spi1 = &ecspi2;
 		spi3 = &ecspi3;
 		spi4 = &ecspi4;
+		usb0 = &usbotg1;
+		usb1 = &usbotg2;
 		usbphy0 = &usbphy1;
 		usbphy1 = &usbphy2;
 	};
@@ -49,20 +51,18 @@
 			device_type = "cpu";
 			reg = <0>;
 			next-level-cache = <&L2>;
-			operating-points = <
+			operating-points =
 				/* kHz    uV */
-				996000  1275000
-				792000  1175000
-				396000  1075000
-				198000	975000
-			>;
-			fsl,soc-operating-points = <
+				<996000  1275000>,
+				<792000  1175000>,
+				<396000  1075000>,
+				<198000	  975000>;
+			fsl,soc-operating-points =
 				/* ARM kHz      SOC-PU uV */
-				996000          1175000
-				792000          1175000
-				396000          1175000
-				198000		1175000
-			>;
+				<996000         1175000>,
+				<792000         1175000>,
+				<396000         1175000>,
+				<198000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SLL_CLK_ARM>,
@@ -72,6 +72,8 @@
 				 <&clks IMX6SLL_CLK_PLL1_SYS>;
 			clock-names = "arm", "pll2_pfd2_396m", "step",
 				      "pll1_sw", "pll1_sys";
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 	};
 
@@ -103,16 +105,6 @@
 		clock-output-names = "ipp_di1";
 	};
 
-	tempmon: temperature-sensor {
-		compatible = "fsl,imx6sll-tempmon", "fsl,imx6sx-tempmon";
-		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-parent = <&gpc>;
-		fsl,tempmon = <&anatop>;
-		nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
-		nvmem-cell-names = "calib", "temp_grade";
-		clocks = <&clks IMX6SLL_CLK_PLL3_USB_OTG>;
-	};
-
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -123,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -134,7 +129,7 @@
 			interrupt-parent = <&intc>;
 		};
 
-		L2: l2-cache@a02000 {
+		L2: cache-controller@a02000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x00a02000 0x1000>;
 			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
@@ -144,7 +139,7 @@
 			arm,data-latency = <4 2 3>;
 		};
 
-		aips1: aips-bus@2000000 {
+		aips1: bus@2000000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -269,7 +264,7 @@
 					status = "disabled";
 				};
 
-				ssi1: ssi-controller@2028000 {
+				ssi1: ssi@2028000 {
 					compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi";
 					reg = <0x02028000 0x4000>;
 					interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
@@ -282,7 +277,7 @@
 					status = "disabled";
 				};
 
-				ssi2: ssi-controller@202c000 {
+				ssi2: ssi@202c000 {
 					compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi";
 					reg = <0x0202c000 0x4000>;
 					interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
@@ -295,7 +290,7 @@
 					status = "disabled";
 				};
 
-				ssi3: ssi-controller@2030000 {
+				ssi3: ssi@2030000 {
 					compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi";
 					reg = <0x02030000 0x4000>;
 					interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
@@ -329,7 +324,7 @@
 				clocks = <&clks IMX6SLL_CLK_PWM1>,
 					 <&clks IMX6SLL_CLK_PWM1>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm2: pwm@2084000 {
@@ -339,7 +334,7 @@
 				clocks = <&clks IMX6SLL_CLK_PWM2>,
 					 <&clks IMX6SLL_CLK_PWM2>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm3: pwm@2088000 {
@@ -349,7 +344,7 @@
 				clocks = <&clks IMX6SLL_CLK_PWM3>,
 					 <&clks IMX6SLL_CLK_PWM3>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm4: pwm@208c000 {
@@ -359,7 +354,7 @@
 				clocks = <&clks IMX6SLL_CLK_PWM4>,
 					 <&clks IMX6SLL_CLK_PWM4>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			gpt1: timer@2098000 {
@@ -529,6 +524,16 @@
 					anatop-max-voltage = <3400000>;
 					anatop-enable-bit = <0>;
 				};
+
+				tempmon: temperature-sensor {
+					compatible = "fsl,imx6sll-tempmon", "fsl,imx6sx-tempmon";
+					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-parent = <&gpc>;
+					fsl,tempmon = <&anatop>;
+					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+					nvmem-cell-names = "calib", "temp_grade";
+					clocks = <&clks IMX6SLL_CLK_PLL3_USB_OTG>;
+				};
 			};
 
 			usbphy1: usb-phy@20c9000 {
@@ -547,7 +552,7 @@
 				reg = <0x020ca000 0x1000>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SLL_CLK_USBPHY2>;
-				phy-reg_3p0-supply = <&reg_3p0>;
+				phy-3p0-supply = <&reg_3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -632,6 +637,15 @@
 				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin";
 			};
 
+			pxp: pxp@20f0000 {
+				compatible = "fsl,imx6sll-pxp", "fsl,imx6ull-pxp";
+				reg = <0x20f0000 0x4000>;
+				interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6SLL_CLK_PXP>;
+				clock-names = "axi";
+			};
+
 			lcdif: lcd-controller@20f8000 {
 				compatible = "fsl,imx6sll-lcdif", "fsl,imx28-lcdif";
 				reg = <0x020f8000 0x4000>;
@@ -643,7 +657,7 @@
 				status = "disabled";
 			};
 
-			dcp: dcp@20fc000 {
+			dcp: crypto@20fc000 {
 				compatible = "fsl,imx28-dcp";
 				reg = <0x020fc000 0x4000>;
 				interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
@@ -654,7 +668,7 @@
 			};
 		};
 
-		aips2: aips-bus@2100000 {
+		aips2: bus@2100000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -775,13 +789,24 @@
 				clocks = <&clks IMX6SLL_CLK_MMDC_P0_IPG>;
 			};
 
-			ocotp: ocotp-ctrl@21bc000 {
+			rngb: rng@21b4000 {
+				compatible = "fsl,imx6sll-rngb", "fsl,imx25-rngb";
+				reg = <0x021b4000 0x4000>;
+				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6SLL_CLK_DUMMY>;
+			};
+
+			ocotp: efuse@21bc000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6sll-ocotp", "syscon";
 				reg = <0x021bc000 0x4000>;
 				clocks = <&clks IMX6SLL_CLK_OCOTP>;
 
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
+
 				tempmon_calib: calib@38 {
 					reg = <0x38 4>;
 				};
diff --git a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
index 832b5c5d7441..cd9cbc9ccc9e 100644
--- a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
@@ -72,7 +72,6 @@
 		pinctrl-0 = <&pinctrl_reg_wlan>;
 		compatible = "regulator-fixed";
 		clocks = <&clks IMX6SX_CLK_CKO>;
-		clock-names = "slow";
 		regulator-name = "wlan-en";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -107,7 +106,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -196,6 +195,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6SX_CLK_CKO2>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_1p8v>;
@@ -229,6 +229,7 @@
 };
 
 &pwm4 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -484,31 +485,31 @@
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
-			MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX		0x1b0b1
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX6SX_PAD_GPIO1_IO06__UART2_TX		0x1b0b1
-			MX6SX_PAD_GPIO1_IO07__UART2_RX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX		0x1b0b1
 		>;
 	};
 
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
-			MX6SX_PAD_QSPI1B_SS0_B__UART3_TX	0x1b0b1
-			MX6SX_PAD_QSPI1B_SCLK__UART3_RX		0x1b0b1
+			MX6SX_PAD_QSPI1B_SS0_B__UART3_DCE_TX		0x1b0b1
+			MX6SX_PAD_QSPI1B_SCLK__UART3_DCE_RX		0x1b0b1
 		>;
 	};
 
 	pinctrl_uart5: uart5grp {
 		fsl,pins = <
-			MX6SX_PAD_KEY_COL3__UART5_TX		0x1b0b1
-			MX6SX_PAD_KEY_ROW3__UART5_RX		0x1b0b1
-			MX6SX_PAD_SD3_DATA6__UART3_RTS_B	0x1b0b1
-			MX6SX_PAD_SD3_DATA7__UART3_CTS_B	0x1b0b1
+			MX6SX_PAD_KEY_COL3__UART5_DCE_TX		0x1b0b1
+			MX6SX_PAD_KEY_ROW3__UART5_DCE_RX		0x1b0b1
+			MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS		0x1b0b1
+			MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS		0x1b0b1
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6sx-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6sx-pinfunc.h
index aa194a2fdd53..f4dc46207954 100644
--- a/arch/arm/boot/dts/imx6sx-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-pinfunc.h
@@ -42,8 +42,8 @@
 #define MX6SX_PAD_GPIO1_IO03__GPIO1_IO_3                          0x0020 0x0368 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO03__CCM_PLL3_BYP                        0x0020 0x0368 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO03__PHY_TCK                             0x0020 0x0368 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO04__UART1_RX                            0x0024 0x036C 0x0830 0x0 0x0
-#define MX6SX_PAD_GPIO1_IO04__UART1_TX                            0x0024 0x036C 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX                        0x0024 0x036C 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO04__UART1_DTE_RX                        0x0024 0x036C 0x0830 0x0 0x0
 #define MX6SX_PAD_GPIO1_IO04__USDHC2_RESET_B                      0x0024 0x036C 0x0000 0x1 0x0
 #define MX6SX_PAD_GPIO1_IO04__ENET1_MDC                           0x0024 0x036C 0x0000 0x2 0x0
 #define MX6SX_PAD_GPIO1_IO04__OSC32K_32K_OUT                      0x0024 0x036C 0x0000 0x3 0x0
@@ -51,8 +51,8 @@
 #define MX6SX_PAD_GPIO1_IO04__GPIO1_IO_4                          0x0024 0x036C 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO04__CCM_PLL2_BYP                        0x0024 0x036C 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO04__PHY_TMS                             0x0024 0x036C 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO05__UART1_RX                            0x0028 0x0370 0x0830 0x0 0x1
-#define MX6SX_PAD_GPIO1_IO05__UART1_TX                            0x0028 0x0370 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX                        0x0028 0x0370 0x0830 0x0 0x1
+#define MX6SX_PAD_GPIO1_IO05__UART1_DTE_TX                        0x0028 0x0370 0x0000 0x0 0x0
 #define MX6SX_PAD_GPIO1_IO05__USDHC2_VSELECT                      0x0028 0x0370 0x0000 0x1 0x0
 #define MX6SX_PAD_GPIO1_IO05__ENET1_MDIO                          0x0028 0x0370 0x0764 0x2 0x0
 #define MX6SX_PAD_GPIO1_IO05__ASRC_ASRC_EXT_CLK                   0x0028 0x0370 0x0000 0x3 0x0
@@ -60,21 +60,23 @@
 #define MX6SX_PAD_GPIO1_IO05__GPIO1_IO_5                          0x0028 0x0370 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO05__SRC_TESTER_ACK                      0x0028 0x0370 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO05__PHY_TDO                             0x0028 0x0370 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO06__UART2_RX                            0x002C 0x0374 0x0838 0x0 0x0
-#define MX6SX_PAD_GPIO1_IO06__UART2_TX                            0x002C 0x0374 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX                        0x002C 0x0374 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART2_DTE_RX                        0x002C 0x0374 0x0838 0x0 0x0
 #define MX6SX_PAD_GPIO1_IO06__USDHC2_CD_B                         0x002C 0x0374 0x086C 0x1 0x1
 #define MX6SX_PAD_GPIO1_IO06__ENET2_MDC                           0x002C 0x0374 0x0000 0x2 0x0
 #define MX6SX_PAD_GPIO1_IO06__CSI1_MCLK                           0x002C 0x0374 0x0000 0x3 0x0
-#define MX6SX_PAD_GPIO1_IO06__UART1_RTS_B                         0x002C 0x0374 0x082C 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART1_DCE_RTS                       0x002C 0x0374 0x082C 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO06__UART1_DTE_CTS                       0x002C 0x0374 0x0000 0x4 0x0
 #define MX6SX_PAD_GPIO1_IO06__GPIO1_IO_6                          0x002C 0x0374 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO06__SRC_ANY_PU_RESET                    0x002C 0x0374 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO06__OCOTP_CTRL_WRAPPER_FUSE_LATCHED     0x002C 0x0374 0x0000 0x7 0x0
-#define MX6SX_PAD_GPIO1_IO07__UART2_RX                            0x0030 0x0378 0x0838 0x0 0x1
-#define MX6SX_PAD_GPIO1_IO07__UART2_TX                            0x0030 0x0378 0x0000 0x0 0x0
+#define MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX                        0x0030 0x0378 0x0838 0x0 0x1
+#define MX6SX_PAD_GPIO1_IO07__UART2_DTE_TX                        0x0030 0x0378 0x0000 0x0 0x0
 #define MX6SX_PAD_GPIO1_IO07__USDHC2_WP                           0x0030 0x0378 0x0870 0x1 0x1
 #define MX6SX_PAD_GPIO1_IO07__ENET2_MDIO                          0x0030 0x0378 0x0770 0x2 0x0
 #define MX6SX_PAD_GPIO1_IO07__AUDMUX_MCLK                         0x0030 0x0378 0x0000 0x3 0x0
-#define MX6SX_PAD_GPIO1_IO07__UART1_CTS_B                         0x0030 0x0378 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO07__UART1_DCE_CTS                       0x0030 0x0378 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO07__UART1_DTE_RTS                       0x0030 0x0378 0x082C 0x4 0x1
 #define MX6SX_PAD_GPIO1_IO07__GPIO1_IO_7                          0x0030 0x0378 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO07__SRC_EARLY_RESET                     0x0030 0x0378 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO07__DCIC2_OUT                           0x0030 0x0378 0x0000 0x7 0x0
@@ -83,7 +85,8 @@
 #define MX6SX_PAD_GPIO1_IO08__WDOG1_WDOG_B                        0x0034 0x037C 0x0000 0x1 0x0
 #define MX6SX_PAD_GPIO1_IO08__SDMA_EXT_EVENT_0                    0x0034 0x037C 0x081C 0x2 0x0
 #define MX6SX_PAD_GPIO1_IO08__CCM_PMIC_RDY                        0x0034 0x037C 0x069C 0x3 0x1
-#define MX6SX_PAD_GPIO1_IO08__UART2_RTS_B                         0x0034 0x037C 0x0834 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO08__UART2_DCE_RTS                       0x0034 0x037C 0x0834 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO08__UART2_DTE_CTS                       0x0034 0x037C 0x0000 0x4 0x0
 #define MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8                          0x0034 0x037C 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO08__SRC_SYSTEM_RESET                    0x0034 0x037C 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO08__DCIC1_OUT                           0x0034 0x037C 0x0000 0x7 0x0
@@ -92,7 +95,8 @@
 #define MX6SX_PAD_GPIO1_IO09__WDOG2_WDOG_B                        0x0038 0x0380 0x0000 0x1 0x0
 #define MX6SX_PAD_GPIO1_IO09__SDMA_EXT_EVENT_1                    0x0038 0x0380 0x0820 0x2 0x0
 #define MX6SX_PAD_GPIO1_IO09__CCM_OUT0                            0x0038 0x0380 0x0000 0x3 0x0
-#define MX6SX_PAD_GPIO1_IO09__UART2_CTS_B                         0x0038 0x0380 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO09__UART2_DCE_CTS                       0x0038 0x0380 0x0000 0x4 0x0
+#define MX6SX_PAD_GPIO1_IO09__UART2_DTE_RTS                       0x0038 0x0380 0x0834 0x4 0x1
 #define MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9                          0x0038 0x0380 0x0000 0x5 0x0
 #define MX6SX_PAD_GPIO1_IO09__SRC_INT_BOOT                        0x0038 0x0380 0x0000 0x6 0x0
 #define MX6SX_PAD_GPIO1_IO09__OBSERVE_MUX_OUT_4                   0x0038 0x0380 0x0000 0x7 0x0
@@ -177,8 +181,8 @@
 #define MX6SX_PAD_CSI_DATA04__ESAI_TX1                            0x005C 0x03A4 0x0794 0x1 0x1
 #define MX6SX_PAD_CSI_DATA04__SPDIF_OUT                           0x005C 0x03A4 0x0000 0x2 0x0
 #define MX6SX_PAD_CSI_DATA04__KPP_COL_6                           0x005C 0x03A4 0x07CC 0x3 0x0
-#define MX6SX_PAD_CSI_DATA04__UART6_RX                            0x005C 0x03A4 0x0858 0x4 0x0
-#define MX6SX_PAD_CSI_DATA04__UART6_TX                            0x005C 0x03A4 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA04__UART6_DCE_RX                        0x005C 0x03A4 0x0858 0x4 0x0
+#define MX6SX_PAD_CSI_DATA04__UART6_DTE_TX                        0x005C 0x03A4 0x0000 0x4 0x0
 #define MX6SX_PAD_CSI_DATA04__GPIO1_IO_18                         0x005C 0x03A4 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_DATA04__WEIM_DATA_19                        0x005C 0x03A4 0x0000 0x6 0x0
 #define MX6SX_PAD_CSI_DATA04__PWM5_OUT                            0x005C 0x03A4 0x0000 0x7 0x0
@@ -188,8 +192,8 @@
 #define MX6SX_PAD_CSI_DATA05__ESAI_TX4_RX1                        0x0060 0x03A8 0x07A0 0x1 0x1
 #define MX6SX_PAD_CSI_DATA05__SPDIF_IN                            0x0060 0x03A8 0x0824 0x2 0x1
 #define MX6SX_PAD_CSI_DATA05__KPP_ROW_6                           0x0060 0x03A8 0x07D8 0x3 0x0
-#define MX6SX_PAD_CSI_DATA05__UART6_RX                            0x0060 0x03A8 0x0858 0x4 0x1
-#define MX6SX_PAD_CSI_DATA05__UART6_TX                            0x0060 0x03A8 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA05__UART6_DCE_TX                        0x0060 0x03A8 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA05__UART6_DTE_RX                        0x0060 0x03A8 0x0858 0x4 0x1
 #define MX6SX_PAD_CSI_DATA05__GPIO1_IO_19                         0x0060 0x03A8 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_DATA05__WEIM_DATA_18                        0x0060 0x03A8 0x0000 0x6 0x0
 #define MX6SX_PAD_CSI_DATA05__PWM6_OUT                            0x0060 0x03A8 0x0000 0x7 0x0
@@ -199,7 +203,8 @@
 #define MX6SX_PAD_CSI_DATA06__ESAI_TX2_RX3                        0x0064 0x03AC 0x0798 0x1 0x1
 #define MX6SX_PAD_CSI_DATA06__I2C4_SCL                            0x0064 0x03AC 0x07C0 0x2 0x2
 #define MX6SX_PAD_CSI_DATA06__KPP_COL_7                           0x0064 0x03AC 0x07D0 0x3 0x0
-#define MX6SX_PAD_CSI_DATA06__UART6_RTS_B                         0x0064 0x03AC 0x0854 0x4 0x0
+#define MX6SX_PAD_CSI_DATA06__UART6_DCE_RTS                       0x0064 0x03AC 0x0854 0x4 0x0
+#define MX6SX_PAD_CSI_DATA06__UART6_DTE_CTS                       0x0064 0x03AC 0x0000 0x4 0x0
 #define MX6SX_PAD_CSI_DATA06__GPIO1_IO_20                         0x0064 0x03AC 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_DATA06__WEIM_DATA_17                        0x0064 0x03AC 0x0000 0x6 0x0
 #define MX6SX_PAD_CSI_DATA06__DCIC2_OUT                           0x0064 0x03AC 0x0000 0x7 0x0
@@ -209,7 +214,8 @@
 #define MX6SX_PAD_CSI_DATA07__ESAI_TX3_RX2                        0x0068 0x03B0 0x079C 0x1 0x1
 #define MX6SX_PAD_CSI_DATA07__I2C4_SDA                            0x0068 0x03B0 0x07C4 0x2 0x2
 #define MX6SX_PAD_CSI_DATA07__KPP_ROW_7                           0x0068 0x03B0 0x07DC 0x3 0x0
-#define MX6SX_PAD_CSI_DATA07__UART6_CTS_B                         0x0068 0x03B0 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA07__UART6_DCE_CTS                       0x0068 0x03B0 0x0000 0x4 0x0
+#define MX6SX_PAD_CSI_DATA07__UART6_DTE_RTS                       0x0068 0x03B0 0x0854 0x4 0x1
 #define MX6SX_PAD_CSI_DATA07__GPIO1_IO_21                         0x0068 0x03B0 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_DATA07__WEIM_DATA_16                        0x0068 0x03B0 0x0000 0x6 0x0
 #define MX6SX_PAD_CSI_DATA07__DCIC1_OUT                           0x0068 0x03B0 0x0000 0x7 0x0
@@ -218,7 +224,8 @@
 #define MX6SX_PAD_CSI_HSYNC__CSI1_HSYNC                           0x006C 0x03B4 0x0700 0x0 0x0
 #define MX6SX_PAD_CSI_HSYNC__ESAI_TX0                             0x006C 0x03B4 0x0790 0x1 0x1
 #define MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD                      0x006C 0x03B4 0x0678 0x2 0x1
-#define MX6SX_PAD_CSI_HSYNC__UART4_RTS_B                          0x006C 0x03B4 0x0844 0x3 0x2
+#define MX6SX_PAD_CSI_HSYNC__UART4_DCE_RTS                        0x006C 0x03B4 0x0844 0x3 0x2
+#define MX6SX_PAD_CSI_HSYNC__UART4_DTE_CTS                        0x006C 0x03B4 0x0000 0x3 0x0
 #define MX6SX_PAD_CSI_HSYNC__MQS_LEFT                             0x006C 0x03B4 0x0000 0x4 0x0
 #define MX6SX_PAD_CSI_HSYNC__GPIO1_IO_22                          0x006C 0x03B4 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_HSYNC__WEIM_DATA_25                         0x006C 0x03B4 0x0000 0x6 0x0
@@ -228,8 +235,8 @@
 #define MX6SX_PAD_CSI_MCLK__CSI1_MCLK                             0x0070 0x03B8 0x0000 0x0 0x0
 #define MX6SX_PAD_CSI_MCLK__ESAI_TX_HF_CLK                        0x0070 0x03B8 0x0784 0x1 0x1
 #define MX6SX_PAD_CSI_MCLK__OSC32K_32K_OUT                        0x0070 0x03B8 0x0000 0x2 0x0
-#define MX6SX_PAD_CSI_MCLK__UART4_RX                              0x0070 0x03B8 0x0848 0x3 0x2
-#define MX6SX_PAD_CSI_MCLK__UART4_TX                              0x0070 0x03B8 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_MCLK__UART4_DCE_RX                          0x0070 0x03B8 0x0848 0x3 0x2
+#define MX6SX_PAD_CSI_MCLK__UART4_DTE_TX                          0x0070 0x03B8 0x0000 0x3 0x0
 #define MX6SX_PAD_CSI_MCLK__ANATOP_32K_OUT                        0x0070 0x03B8 0x0000 0x4 0x0
 #define MX6SX_PAD_CSI_MCLK__GPIO1_IO_23                           0x0070 0x03B8 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_MCLK__WEIM_DATA_26                          0x0070 0x03B8 0x0000 0x6 0x0
@@ -239,8 +246,8 @@
 #define MX6SX_PAD_CSI_PIXCLK__CSI1_PIXCLK                         0x0074 0x03BC 0x0704 0x0 0x0
 #define MX6SX_PAD_CSI_PIXCLK__ESAI_RX_HF_CLK                      0x0074 0x03BC 0x0780 0x1 0x1
 #define MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK                         0x0074 0x03BC 0x0000 0x2 0x0
-#define MX6SX_PAD_CSI_PIXCLK__UART4_RX                            0x0074 0x03BC 0x0848 0x3 0x3
-#define MX6SX_PAD_CSI_PIXCLK__UART4_TX                            0x0074 0x03BC 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_PIXCLK__UART4_DCE_TX                        0x0074 0x03BC 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_PIXCLK__UART4_DTE_RX                        0x0074 0x03BC 0x0848 0x3 0x3
 #define MX6SX_PAD_CSI_PIXCLK__ANATOP_24M_OUT                      0x0074 0x03BC 0x0000 0x4 0x0
 #define MX6SX_PAD_CSI_PIXCLK__GPIO1_IO_24                         0x0074 0x03BC 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_PIXCLK__WEIM_DATA_27                        0x0074 0x03BC 0x0000 0x6 0x0
@@ -250,7 +257,8 @@
 #define MX6SX_PAD_CSI_VSYNC__CSI1_VSYNC                           0x0078 0x03C0 0x0708 0x0 0x0
 #define MX6SX_PAD_CSI_VSYNC__ESAI_TX5_RX0                         0x0078 0x03C0 0x07A4 0x1 0x1
 #define MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD                      0x0078 0x03C0 0x0674 0x2 0x1
-#define MX6SX_PAD_CSI_VSYNC__UART4_CTS_B                          0x0078 0x03C0 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_VSYNC__UART4_DCE_CTS                        0x0078 0x03C0 0x0000 0x3 0x0
+#define MX6SX_PAD_CSI_VSYNC__UART4_DTE_RTS                        0x0078 0x03C0 0x0844 0x3 0x3
 #define MX6SX_PAD_CSI_VSYNC__MQS_RIGHT                            0x0078 0x03C0 0x0000 0x4 0x0
 #define MX6SX_PAD_CSI_VSYNC__GPIO1_IO_25                          0x0078 0x03C0 0x0000 0x5 0x0
 #define MX6SX_PAD_CSI_VSYNC__WEIM_DATA_24                         0x0078 0x03C0 0x0000 0x6 0x0
@@ -330,8 +338,8 @@
 #define MX6SX_PAD_ENET2_COL__ENET2_COL                            0x0094 0x03DC 0x0000 0x0 0x0
 #define MX6SX_PAD_ENET2_COL__ENET1_MDC                            0x0094 0x03DC 0x0000 0x1 0x0
 #define MX6SX_PAD_ENET2_COL__AUDMUX_AUD4_RXC                      0x0094 0x03DC 0x064C 0x2 0x1
-#define MX6SX_PAD_ENET2_COL__UART1_RX                             0x0094 0x03DC 0x0830 0x3 0x2
-#define MX6SX_PAD_ENET2_COL__UART1_TX                             0x0094 0x03DC 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_COL__UART1_DCE_RX                         0x0094 0x03DC 0x0830 0x3 0x2
+#define MX6SX_PAD_ENET2_COL__UART1_DTE_TX                         0x0094 0x03DC 0x0000 0x3 0x0
 #define MX6SX_PAD_ENET2_COL__SPDIF_IN                             0x0094 0x03DC 0x0824 0x4 0x3
 #define MX6SX_PAD_ENET2_COL__GPIO2_IO_6                           0x0094 0x03DC 0x0000 0x5 0x0
 #define MX6SX_PAD_ENET2_COL__ANATOP_OTG1_ID                       0x0094 0x03DC 0x0624 0x6 0x1
@@ -341,8 +349,8 @@
 #define MX6SX_PAD_ENET2_CRS__ENET2_CRS                            0x0098 0x03E0 0x0000 0x0 0x0
 #define MX6SX_PAD_ENET2_CRS__ENET1_MDIO                           0x0098 0x03E0 0x0764 0x1 0x2
 #define MX6SX_PAD_ENET2_CRS__AUDMUX_AUD4_RXFS                     0x0098 0x03E0 0x0650 0x2 0x1
-#define MX6SX_PAD_ENET2_CRS__UART1_RX                             0x0098 0x03E0 0x0830 0x3 0x3
-#define MX6SX_PAD_ENET2_CRS__UART1_TX                             0x0098 0x03E0 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_CRS__UART1_DCE_TX                         0x0098 0x03E0 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_CRS__UART1_DTE_RX                         0x0098 0x03E0 0x0830 0x3 0x3
 #define MX6SX_PAD_ENET2_CRS__MLB_SIG                              0x0098 0x03E0 0x07F0 0x4 0x1
 #define MX6SX_PAD_ENET2_CRS__GPIO2_IO_7                           0x0098 0x03E0 0x0000 0x5 0x0
 #define MX6SX_PAD_ENET2_CRS__ANATOP_OTG2_ID                       0x0098 0x03E0 0x0628 0x6 0x1
@@ -352,7 +360,8 @@
 #define MX6SX_PAD_ENET2_RX_CLK__ENET2_RX_CLK                      0x009C 0x03E4 0x0774 0x0 0x0
 #define MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M                 0x009C 0x03E4 0x0000 0x1 0x0
 #define MX6SX_PAD_ENET2_RX_CLK__I2C3_SCL                          0x009C 0x03E4 0x07B8 0x2 0x1
-#define MX6SX_PAD_ENET2_RX_CLK__UART1_RTS_B                       0x009C 0x03E4 0x082C 0x3 0x2
+#define MX6SX_PAD_ENET2_RX_CLK__UART1_DCE_RTS                     0x009C 0x03E4 0x082C 0x3 0x2
+#define MX6SX_PAD_ENET2_RX_CLK__UART1_DTE_CTS                     0x009C 0x03E4 0x0000 0x3 0x0
 #define MX6SX_PAD_ENET2_RX_CLK__MLB_DATA                          0x009C 0x03E4 0x07EC 0x4 0x1
 #define MX6SX_PAD_ENET2_RX_CLK__GPIO2_IO_8                        0x009C 0x03E4 0x0000 0x5 0x0
 #define MX6SX_PAD_ENET2_RX_CLK__USB_OTG2_OC                       0x009C 0x03E4 0x085C 0x6 0x1
@@ -362,7 +371,8 @@
 #define MX6SX_PAD_ENET2_TX_CLK__ENET2_TX_CLK                      0x00A0 0x03E8 0x0000 0x0 0x0
 #define MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2                    0x00A0 0x03E8 0x076C 0x1 0x1
 #define MX6SX_PAD_ENET2_TX_CLK__I2C3_SDA                          0x00A0 0x03E8 0x07BC 0x2 0x1
-#define MX6SX_PAD_ENET2_TX_CLK__UART1_CTS_B                       0x00A0 0x03E8 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_TX_CLK__UART1_DCE_CTS                     0x00A0 0x03E8 0x0000 0x3 0x0
+#define MX6SX_PAD_ENET2_TX_CLK__UART1_DTE_RTS                     0x00A0 0x03E8 0x082C 0x3 0x3
 #define MX6SX_PAD_ENET2_TX_CLK__MLB_CLK                           0x00A0 0x03E8 0x07E8 0x4 0x1
 #define MX6SX_PAD_ENET2_TX_CLK__GPIO2_IO_9                        0x00A0 0x03E8 0x0000 0x5 0x0
 #define MX6SX_PAD_ENET2_TX_CLK__USB_OTG2_PWR                      0x00A0 0x03E8 0x0000 0x6 0x0
@@ -371,7 +381,8 @@
 #define MX6SX_PAD_ENET2_TX_CLK__PCIE_CTRL_DEBUG_24                0x00A0 0x03E8 0x0000 0x9 0x0
 #define MX6SX_PAD_KEY_COL0__KPP_COL_0                             0x00A4 0x03EC 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_COL0__USDHC3_CD_B                           0x00A4 0x03EC 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_COL0__UART6_RTS_B                           0x00A4 0x03EC 0x0854 0x2 0x2
+#define MX6SX_PAD_KEY_COL0__UART6_DCE_RTS                         0x00A4 0x03EC 0x0854 0x2 0x2
+#define MX6SX_PAD_KEY_COL0__UART6_DTE_CTS                         0x00A4 0x03EC 0x0000 0x2 0x0
 #define MX6SX_PAD_KEY_COL0__ECSPI1_SCLK                           0x00A4 0x03EC 0x0710 0x3 0x0
 #define MX6SX_PAD_KEY_COL0__AUDMUX_AUD5_TXC                       0x00A4 0x03EC 0x066C 0x4 0x0
 #define MX6SX_PAD_KEY_COL0__GPIO2_IO_10                           0x00A4 0x03EC 0x0000 0x5 0x0
@@ -380,8 +391,8 @@
 #define MX6SX_PAD_KEY_COL0__VADC_DATA_0                           0x00A4 0x03EC 0x0000 0x8 0x0
 #define MX6SX_PAD_KEY_COL1__KPP_COL_1                             0x00A8 0x03F0 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_COL1__USDHC3_RESET_B                        0x00A8 0x03F0 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_COL1__UART6_RX                              0x00A8 0x03F0 0x0858 0x2 0x2
-#define MX6SX_PAD_KEY_COL1__UART6_TX                              0x00A8 0x03F0 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL1__UART6_DCE_TX                          0x00A8 0x03F0 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL1__UART6_DTE_RX                          0x00A8 0x03F0 0x0858 0x2 0x2
 #define MX6SX_PAD_KEY_COL1__ECSPI1_MISO                           0x00A8 0x03F0 0x0714 0x3 0x0
 #define MX6SX_PAD_KEY_COL1__AUDMUX_AUD5_TXFS                      0x00A8 0x03F0 0x0670 0x4 0x0
 #define MX6SX_PAD_KEY_COL1__GPIO2_IO_11                           0x00A8 0x03F0 0x0000 0x5 0x0
@@ -389,7 +400,8 @@
 #define MX6SX_PAD_KEY_COL1__SAI2_TX_SYNC                          0x00A8 0x03F0 0x0818 0x7 0x0
 #define MX6SX_PAD_KEY_COL2__KPP_COL_2                             0x00AC 0x03F4 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_COL2__USDHC4_CD_B                           0x00AC 0x03F4 0x0874 0x1 0x1
-#define MX6SX_PAD_KEY_COL2__UART5_RTS_B                           0x00AC 0x03F4 0x084C 0x2 0x2
+#define MX6SX_PAD_KEY_COL2__UART5_DCE_RTS                         0x00AC 0x03F4 0x084C 0x2 0x2
+#define MX6SX_PAD_KEY_COL2__UART5_DTE_CTS                         0x00AC 0x03F4 0x0000 0x2 0x0
 #define MX6SX_PAD_KEY_COL2__CAN1_TX                               0x00AC 0x03F4 0x0000 0x3 0x0
 #define MX6SX_PAD_KEY_COL2__CANFD_TX1                             0x00AC 0x03F4 0x0000 0x4 0x0
 #define MX6SX_PAD_KEY_COL2__GPIO2_IO_12                           0x00AC 0x03F4 0x0000 0x5 0x0
@@ -397,8 +409,8 @@
 #define MX6SX_PAD_KEY_COL2__ECSPI1_RDY                            0x00AC 0x03F4 0x0000 0x7 0x0
 #define MX6SX_PAD_KEY_COL3__KPP_COL_3                             0x00B0 0x03F8 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_COL3__USDHC4_LCTL                           0x00B0 0x03F8 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_COL3__UART5_RX                              0x00B0 0x03F8 0x0850 0x2 0x2
-#define MX6SX_PAD_KEY_COL3__UART5_TX                              0x00B0 0x03F8 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL3__UART5_DCE_TX                          0x00B0 0x03F8 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_COL3__UART5_DTE_RX                          0x00B0 0x03F8 0x0850 0x2 0x2
 #define MX6SX_PAD_KEY_COL3__CAN2_TX                               0x00B0 0x03F8 0x0000 0x3 0x0
 #define MX6SX_PAD_KEY_COL3__CANFD_TX2                             0x00B0 0x03F8 0x0000 0x4 0x0
 #define MX6SX_PAD_KEY_COL3__GPIO2_IO_13                           0x00B0 0x03F8 0x0000 0x5 0x0
@@ -414,7 +426,8 @@
 #define MX6SX_PAD_KEY_COL4__SAI2_RX_BCLK                          0x00B4 0x03FC 0x0808 0x7 0x0
 #define MX6SX_PAD_KEY_ROW0__KPP_ROW_0                             0x00B8 0x0400 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_ROW0__USDHC3_WP                             0x00B8 0x0400 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_ROW0__UART6_CTS_B                           0x00B8 0x0400 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW0__UART6_DCE_CTS                         0x00B8 0x0400 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW0__UART6_DTE_RTS                         0x00B8 0x0400 0x0854 0x2 0x3
 #define MX6SX_PAD_KEY_ROW0__ECSPI1_MOSI                           0x00B8 0x0400 0x0718 0x3 0x0
 #define MX6SX_PAD_KEY_ROW0__AUDMUX_AUD5_TXD                       0x00B8 0x0400 0x0660 0x4 0x0
 #define MX6SX_PAD_KEY_ROW0__GPIO2_IO_15                           0x00B8 0x0400 0x0000 0x5 0x0
@@ -423,8 +436,8 @@
 #define MX6SX_PAD_KEY_ROW0__GPU_IDLE                              0x00B8 0x0400 0x0000 0x8 0x0
 #define MX6SX_PAD_KEY_ROW1__KPP_ROW_1                             0x00BC 0x0404 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_ROW1__USDHC4_VSELECT                        0x00BC 0x0404 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_ROW1__UART6_RX                              0x00BC 0x0404 0x0858 0x2 0x3
-#define MX6SX_PAD_KEY_ROW1__UART6_TX                              0x00BC 0x0404 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW1__UART6_DCE_RX                          0x00BC 0x0404 0x0858 0x2 0x3
+#define MX6SX_PAD_KEY_ROW1__UART6_DTE_TX                          0x00BC 0x0404 0x0000 0x2 0x0
 #define MX6SX_PAD_KEY_ROW1__ECSPI1_SS0                            0x00BC 0x0404 0x071C 0x3 0x0
 #define MX6SX_PAD_KEY_ROW1__AUDMUX_AUD5_RXD                       0x00BC 0x0404 0x065C 0x4 0x0
 #define MX6SX_PAD_KEY_ROW1__GPIO2_IO_16                           0x00BC 0x0404 0x0000 0x5 0x0
@@ -433,7 +446,8 @@
 #define MX6SX_PAD_KEY_ROW1__M4_NMI                                0x00BC 0x0404 0x0000 0x8 0x0
 #define MX6SX_PAD_KEY_ROW2__KPP_ROW_2                             0x00C0 0x0408 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_ROW2__USDHC4_WP                             0x00C0 0x0408 0x0878 0x1 0x1
-#define MX6SX_PAD_KEY_ROW2__UART5_CTS_B                           0x00C0 0x0408 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS                         0x00C0 0x0408 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW2__UART5_DTE_RTS                         0x00C0 0x0408 0x084C 0x2 0x3
 #define MX6SX_PAD_KEY_ROW2__CAN1_RX                               0x00C0 0x0408 0x068C 0x3 0x1
 #define MX6SX_PAD_KEY_ROW2__CANFD_RX1                             0x00C0 0x0408 0x0694 0x4 0x1
 #define MX6SX_PAD_KEY_ROW2__GPIO2_IO_17                           0x00C0 0x0408 0x0000 0x5 0x0
@@ -441,8 +455,8 @@
 #define MX6SX_PAD_KEY_ROW2__ECSPI1_SS3                            0x00C0 0x0408 0x0000 0x7 0x0
 #define MX6SX_PAD_KEY_ROW3__KPP_ROW_3                             0x00C4 0x040C 0x0000 0x0 0x0
 #define MX6SX_PAD_KEY_ROW3__USDHC3_LCTL                           0x00C4 0x040C 0x0000 0x1 0x0
-#define MX6SX_PAD_KEY_ROW3__UART5_RX                              0x00C4 0x040C 0x0850 0x2 0x3
-#define MX6SX_PAD_KEY_ROW3__UART5_TX                              0x00C4 0x040C 0x0000 0x2 0x0
+#define MX6SX_PAD_KEY_ROW3__UART5_DCE_RX                          0x00C4 0x040C 0x0850 0x2 0x3
+#define MX6SX_PAD_KEY_ROW3__UART5_DTE_TX                          0x00C4 0x040C 0x0000 0x2 0x0
 #define MX6SX_PAD_KEY_ROW3__CAN2_RX                               0x00C4 0x040C 0x0690 0x3 0x1
 #define MX6SX_PAD_KEY_ROW3__CANFD_RX2                             0x00C4 0x040C 0x0698 0x4 0x1
 #define MX6SX_PAD_KEY_ROW3__GPIO2_IO_18                           0x00C4 0x040C 0x0000 0x5 0x0
@@ -815,7 +829,8 @@
 #define MX6SX_PAD_NAND_DATA04__RAWNAND_DATA04                     0x0160 0x04A8 0x0000 0x0 0x0
 #define MX6SX_PAD_NAND_DATA04__USDHC2_DATA4                       0x0160 0x04A8 0x0000 0x1 0x0
 #define MX6SX_PAD_NAND_DATA04__QSPI2_B_SS1_B                      0x0160 0x04A8 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA04__UART3_RTS_B                        0x0160 0x04A8 0x083C 0x3 0x0
+#define MX6SX_PAD_NAND_DATA04__UART3_DCE_RTS                      0x0160 0x04A8 0x083C 0x3 0x0
+#define MX6SX_PAD_NAND_DATA04__UART3_DTE_CTS                      0x0160 0x04A8 0x0000 0x3 0x0
 #define MX6SX_PAD_NAND_DATA04__AUDMUX_AUD4_RXFS                   0x0160 0x04A8 0x0650 0x4 0x0
 #define MX6SX_PAD_NAND_DATA04__GPIO4_IO_8                         0x0160 0x04A8 0x0000 0x5 0x0
 #define MX6SX_PAD_NAND_DATA04__WEIM_AD_4                          0x0160 0x04A8 0x0000 0x6 0x0
@@ -825,7 +840,8 @@
 #define MX6SX_PAD_NAND_DATA05__RAWNAND_DATA05                     0x0164 0x04AC 0x0000 0x0 0x0
 #define MX6SX_PAD_NAND_DATA05__USDHC2_DATA5                       0x0164 0x04AC 0x0000 0x1 0x0
 #define MX6SX_PAD_NAND_DATA05__QSPI2_B_DQS                        0x0164 0x04AC 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA05__UART3_CTS_B                        0x0164 0x04AC 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA05__UART3_DCE_CTS                      0x0164 0x04AC 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA05__UART3_DTE_RTS                      0x0164 0x04AC 0x083C 0x3 0x1
 #define MX6SX_PAD_NAND_DATA05__AUDMUX_AUD4_RXC                    0x0164 0x04AC 0x064C 0x4 0x0
 #define MX6SX_PAD_NAND_DATA05__GPIO4_IO_9                         0x0164 0x04AC 0x0000 0x5 0x0
 #define MX6SX_PAD_NAND_DATA05__WEIM_AD_5                          0x0164 0x04AC 0x0000 0x6 0x0
@@ -835,8 +851,8 @@
 #define MX6SX_PAD_NAND_DATA06__RAWNAND_DATA06                     0x0168 0x04B0 0x0000 0x0 0x0
 #define MX6SX_PAD_NAND_DATA06__USDHC2_DATA6                       0x0168 0x04B0 0x0000 0x1 0x0
 #define MX6SX_PAD_NAND_DATA06__QSPI2_A_SS1_B                      0x0168 0x04B0 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA06__UART3_RX                           0x0168 0x04B0 0x0840 0x3 0x0
-#define MX6SX_PAD_NAND_DATA06__UART3_TX                           0x0168 0x04B0 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA06__UART3_DCE_RX                       0x0168 0x04B0 0x0840 0x3 0x0
+#define MX6SX_PAD_NAND_DATA06__UART3_DTE_TX                       0x0168 0x04B0 0x0000 0x3 0x0
 #define MX6SX_PAD_NAND_DATA06__PWM3_OUT                           0x0168 0x04B0 0x0000 0x4 0x0
 #define MX6SX_PAD_NAND_DATA06__GPIO4_IO_10                        0x0168 0x04B0 0x0000 0x5 0x0
 #define MX6SX_PAD_NAND_DATA06__WEIM_AD_6                          0x0168 0x04B0 0x0000 0x6 0x0
@@ -846,8 +862,8 @@
 #define MX6SX_PAD_NAND_DATA07__RAWNAND_DATA07                     0x016C 0x04B4 0x0000 0x0 0x0
 #define MX6SX_PAD_NAND_DATA07__USDHC2_DATA7                       0x016C 0x04B4 0x0000 0x1 0x0
 #define MX6SX_PAD_NAND_DATA07__QSPI2_A_DQS                        0x016C 0x04B4 0x0000 0x2 0x0
-#define MX6SX_PAD_NAND_DATA07__UART3_RX                           0x016C 0x04B4 0x0840 0x3 0x1
-#define MX6SX_PAD_NAND_DATA07__UART3_TX                           0x016C 0x04B4 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA07__UART3_DCE_TX                       0x016C 0x04B4 0x0000 0x3 0x0
+#define MX6SX_PAD_NAND_DATA07__UART3_DTE_RX                       0x016C 0x04B4 0x0840 0x3 0x1
 #define MX6SX_PAD_NAND_DATA07__PWM4_OUT                           0x016C 0x04B4 0x0000 0x4 0x0
 #define MX6SX_PAD_NAND_DATA07__GPIO4_IO_11                        0x016C 0x04B4 0x0000 0x5 0x0
 #define MX6SX_PAD_NAND_DATA07__WEIM_AD_7                          0x016C 0x04B4 0x0000 0x6 0x0
@@ -967,7 +983,8 @@
 #define MX6SX_PAD_QSPI1A_SS1_B__SIM_M_HADDR_12                    0x019C 0x04E4 0x0000 0x7 0x0
 #define MX6SX_PAD_QSPI1A_SS1_B__SDMA_DEBUG_PC_3                   0x019C 0x04E4 0x0000 0x9 0x0
 #define MX6SX_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0                    0x01A0 0x04E8 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_DATA0__UART3_CTS_B                       0x01A0 0x04E8 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_DATA0__UART3_DCE_CTS                     0x01A0 0x04E8 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_DATA0__UART3_DTE_RTS                     0x01A0 0x04E8 0x083C 0x1 0x4
 #define MX6SX_PAD_QSPI1B_DATA0__ECSPI3_MOSI                       0x01A0 0x04E8 0x0738 0x2 0x1
 #define MX6SX_PAD_QSPI1B_DATA0__ESAI_RX_FS                        0x01A0 0x04E8 0x0778 0x3 0x2
 #define MX6SX_PAD_QSPI1B_DATA0__CSI1_DATA_22                      0x01A0 0x04E8 0x06F4 0x4 0x1
@@ -975,7 +992,8 @@
 #define MX6SX_PAD_QSPI1B_DATA0__WEIM_DATA_14                      0x01A0 0x04E8 0x0000 0x6 0x0
 #define MX6SX_PAD_QSPI1B_DATA0__SIM_M_HADDR_9                     0x01A0 0x04E8 0x0000 0x7 0x0
 #define MX6SX_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1                    0x01A4 0x04EC 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_DATA1__UART3_RTS_B                       0x01A4 0x04EC 0x083C 0x1 0x5
+#define MX6SX_PAD_QSPI1B_DATA1__UART3_DCE_RTS                     0x01A4 0x04EC 0x083C 0x1 0x5
+#define MX6SX_PAD_QSPI1B_DATA1__UART3_DTE_CTS                     0x01A4 0x04EC 0x0000 0x1 0x0
 #define MX6SX_PAD_QSPI1B_DATA1__ECSPI3_MISO                       0x01A4 0x04EC 0x0734 0x2 0x1
 #define MX6SX_PAD_QSPI1B_DATA1__ESAI_RX_CLK                       0x01A4 0x04EC 0x0788 0x3 0x2
 #define MX6SX_PAD_QSPI1B_DATA1__CSI1_DATA_21                      0x01A4 0x04EC 0x06F0 0x4 0x1
@@ -1007,8 +1025,8 @@
 #define MX6SX_PAD_QSPI1B_DQS__WEIM_DATA_15                        0x01B0 0x04F8 0x0000 0x6 0x0
 #define MX6SX_PAD_QSPI1B_DQS__SIM_M_HADDR_15                      0x01B0 0x04F8 0x0000 0x7 0x0
 #define MX6SX_PAD_QSPI1B_SCLK__QSPI1_B_SCLK                       0x01B4 0x04FC 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_SCLK__UART3_RX                           0x01B4 0x04FC 0x0840 0x1 0x4
-#define MX6SX_PAD_QSPI1B_SCLK__UART3_TX                           0x01B4 0x04FC 0x0000 0x0 0x0
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_DCE_RX                       0x01B4 0x04FC 0x0840 0x1 0x4
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_DTE_TX                       0x01B4 0x04FC 0x0000 0x1 0x0
 #define MX6SX_PAD_QSPI1B_SCLK__ECSPI3_SCLK                        0x01B4 0x04FC 0x0730 0x2 0x1
 #define MX6SX_PAD_QSPI1B_SCLK__ESAI_RX_HF_CLK                     0x01B4 0x04FC 0x0780 0x3 0x2
 #define MX6SX_PAD_QSPI1B_SCLK__CSI1_DATA_16                       0x01B4 0x04FC 0x06DC 0x4 0x1
@@ -1016,8 +1034,8 @@
 #define MX6SX_PAD_QSPI1B_SCLK__WEIM_DATA_8                        0x01B4 0x04FC 0x0000 0x6 0x0
 #define MX6SX_PAD_QSPI1B_SCLK__SIM_M_HADDR_11                     0x01B4 0x04FC 0x0000 0x7 0x0
 #define MX6SX_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B                     0x01B8 0x0500 0x0000 0x0 0x0
-#define MX6SX_PAD_QSPI1B_SS0_B__UART3_RX                          0x01B8 0x0500 0x0840 0x1 0x5
-#define MX6SX_PAD_QSPI1B_SS0_B__UART3_TX                          0x01B8 0x0500 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_DCE_TX                      0x01B8 0x0500 0x0000 0x1 0x0
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_DTE_RX                      0x01B8 0x0500 0x0840 0x1 0x5
 #define MX6SX_PAD_QSPI1B_SS0_B__ECSPI3_SS0                        0x01B8 0x0500 0x073C 0x2 0x1
 #define MX6SX_PAD_QSPI1B_SS0_B__ESAI_TX_HF_CLK                    0x01B8 0x0500 0x0784 0x3 0x3
 #define MX6SX_PAD_QSPI1B_SS0_B__CSI1_DATA_17                      0x01B8 0x0500 0x06E0 0x4 0x1
@@ -1224,8 +1242,8 @@
 #define MX6SX_PAD_SD1_DATA0__AUDMUX_AUD5_RXD                      0x0228 0x0570 0x065C 0x1 0x1
 #define MX6SX_PAD_SD1_DATA0__CAAM_WRAPPER_RNG_OSC_OBS             0x0228 0x0570 0x0000 0x2 0x0
 #define MX6SX_PAD_SD1_DATA0__GPT_CAPTURE1                         0x0228 0x0570 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA0__UART2_RX                             0x0228 0x0570 0x0838 0x4 0x2
-#define MX6SX_PAD_SD1_DATA0__UART2_TX                             0x0228 0x0570 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA0__UART2_DCE_RX                         0x0228 0x0570 0x0838 0x4 0x2
+#define MX6SX_PAD_SD1_DATA0__UART2_DTE_TX                         0x0228 0x0570 0x0000 0x4 0x0
 #define MX6SX_PAD_SD1_DATA0__GPIO6_IO_2                           0x0228 0x0570 0x0000 0x5 0x0
 #define MX6SX_PAD_SD1_DATA0__ENET1_1588_EVENT1_IN                 0x0228 0x0570 0x0000 0x6 0x0
 #define MX6SX_PAD_SD1_DATA0__CCM_OUT2                             0x0228 0x0570 0x0000 0x7 0x0
@@ -1235,8 +1253,8 @@
 #define MX6SX_PAD_SD1_DATA1__AUDMUX_AUD5_TXC                      0x022C 0x0574 0x066C 0x1 0x1
 #define MX6SX_PAD_SD1_DATA1__PWM4_OUT                             0x022C 0x0574 0x0000 0x2 0x0
 #define MX6SX_PAD_SD1_DATA1__GPT_CAPTURE2                         0x022C 0x0574 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA1__UART2_RX                             0x022C 0x0574 0x0838 0x4 0x3
-#define MX6SX_PAD_SD1_DATA1__UART2_TX                             0x022C 0x0574 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA1__UART2_DCE_TX                         0x022C 0x0574 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA1__UART2_DTE_RX                         0x022C 0x0574 0x0838 0x4 0x3
 #define MX6SX_PAD_SD1_DATA1__GPIO6_IO_3                           0x022C 0x0574 0x0000 0x5 0x0
 #define MX6SX_PAD_SD1_DATA1__ENET1_1588_EVENT1_OUT                0x022C 0x0574 0x0000 0x6 0x0
 #define MX6SX_PAD_SD1_DATA1__CCM_CLKO2                            0x022C 0x0574 0x0000 0x7 0x0
@@ -1246,7 +1264,8 @@
 #define MX6SX_PAD_SD1_DATA2__AUDMUX_AUD5_TXFS                     0x0230 0x0578 0x0670 0x1 0x1
 #define MX6SX_PAD_SD1_DATA2__PWM3_OUT                             0x0230 0x0578 0x0000 0x2 0x0
 #define MX6SX_PAD_SD1_DATA2__GPT_COMPARE2                         0x0230 0x0578 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA2__UART2_CTS_B                          0x0230 0x0578 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA2__UART2_DCE_CTS                        0x0230 0x0578 0x0000 0x4 0x0
+#define MX6SX_PAD_SD1_DATA2__UART2_DTE_RTS                        0x0230 0x0578 0x0834 0x4 0x2
 #define MX6SX_PAD_SD1_DATA2__GPIO6_IO_4                           0x0230 0x0578 0x0000 0x5 0x0
 #define MX6SX_PAD_SD1_DATA2__ECSPI4_RDY                           0x0230 0x0578 0x0000 0x6 0x0
 #define MX6SX_PAD_SD1_DATA2__CCM_OUT0                             0x0230 0x0578 0x0000 0x7 0x0
@@ -1255,7 +1274,8 @@
 #define MX6SX_PAD_SD1_DATA3__AUDMUX_AUD5_TXD                      0x0234 0x057C 0x0660 0x1 0x1
 #define MX6SX_PAD_SD1_DATA3__AUDMUX_AUD5_RXD                      0x0234 0x057C 0x065C 0x2 0x2
 #define MX6SX_PAD_SD1_DATA3__GPT_COMPARE3                         0x0234 0x057C 0x0000 0x3 0x0
-#define MX6SX_PAD_SD1_DATA3__UART2_RTS_B                          0x0234 0x057C 0x0834 0x4 0x3
+#define MX6SX_PAD_SD1_DATA3__UART2_DCE_RTS                        0x0234 0x057C 0x0834 0x4 0x3
+#define MX6SX_PAD_SD1_DATA3__UART2_DTE_CTS                        0x0234 0x057C 0x0000 0x4 0x0
 #define MX6SX_PAD_SD1_DATA3__GPIO6_IO_5                           0x0234 0x057C 0x0000 0x5 0x0
 #define MX6SX_PAD_SD1_DATA3__ECSPI4_SS1                           0x0234 0x057C 0x0000 0x6 0x0
 #define MX6SX_PAD_SD1_DATA3__CCM_PMIC_RDY                         0x0234 0x057C 0x069C 0x7 0x2
@@ -1287,8 +1307,8 @@
 #define MX6SX_PAD_SD2_DATA0__I2C4_SDA                             0x0240 0x0588 0x07C4 0x4 0x3
 #define MX6SX_PAD_SD2_DATA0__GPIO6_IO_8                           0x0240 0x0588 0x0000 0x5 0x0
 #define MX6SX_PAD_SD2_DATA0__ECSPI4_SS3                           0x0240 0x0588 0x0000 0x6 0x0
-#define MX6SX_PAD_SD2_DATA0__UART4_RX                             0x0240 0x0588 0x0848 0x7 0x4
-#define MX6SX_PAD_SD2_DATA0__UART4_TX                             0x0240 0x0588 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA0__UART4_DCE_RX                         0x0240 0x0588 0x0848 0x7 0x4
+#define MX6SX_PAD_SD2_DATA0__UART4_DTE_TX                         0x0240 0x0588 0x0000 0x7 0x0
 #define MX6SX_PAD_SD2_DATA0__VADC_CLAMP_CURRENT_0                 0x0240 0x0588 0x0000 0x8 0x0
 #define MX6SX_PAD_SD2_DATA0__MMDC_DEBUG_50                        0x0240 0x0588 0x0000 0x9 0x0
 #define MX6SX_PAD_SD2_DATA1__USDHC2_DATA1                         0x0244 0x058C 0x0000 0x0 0x0
@@ -1298,8 +1318,8 @@
 #define MX6SX_PAD_SD2_DATA1__I2C4_SCL                             0x0244 0x058C 0x07C0 0x4 0x3
 #define MX6SX_PAD_SD2_DATA1__GPIO6_IO_9                           0x0244 0x058C 0x0000 0x5 0x0
 #define MX6SX_PAD_SD2_DATA1__ECSPI4_SS2                           0x0244 0x058C 0x0000 0x6 0x0
-#define MX6SX_PAD_SD2_DATA1__UART4_RX                             0x0244 0x058C 0x0848 0x7 0x5
-#define MX6SX_PAD_SD2_DATA1__UART4_TX                             0x0244 0x058C 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA1__UART4_DCE_TX                         0x0244 0x058C 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA1__UART4_DTE_RX                         0x0244 0x058C 0x0848 0x7 0x5
 #define MX6SX_PAD_SD2_DATA1__VADC_CLAMP_CURRENT_1                 0x0244 0x058C 0x0000 0x8 0x0
 #define MX6SX_PAD_SD2_DATA1__MMDC_DEBUG_49                        0x0244 0x058C 0x0000 0x9 0x0
 #define MX6SX_PAD_SD2_DATA2__USDHC2_DATA2                         0x0248 0x0590 0x0000 0x0 0x0
@@ -1309,8 +1329,8 @@
 #define MX6SX_PAD_SD2_DATA2__SDMA_EXT_EVENT_0                     0x0248 0x0590 0x081C 0x4 0x2
 #define MX6SX_PAD_SD2_DATA2__GPIO6_IO_10                          0x0248 0x0590 0x0000 0x5 0x0
 #define MX6SX_PAD_SD2_DATA2__SPDIF_OUT                            0x0248 0x0590 0x0000 0x6 0x0
-#define MX6SX_PAD_SD2_DATA2__UART6_RX                             0x0248 0x0590 0x0858 0x7 0x4
-#define MX6SX_PAD_SD2_DATA2__UART6_TX                             0x0248 0x0590 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA2__UART6_DCE_RX                         0x0248 0x0590 0x0858 0x7 0x4
+#define MX6SX_PAD_SD2_DATA2__UART6_DTE_TX                         0x0248 0x0590 0x0000 0x7 0x0
 #define MX6SX_PAD_SD2_DATA2__VADC_CLAMP_CURRENT_2                 0x0248 0x0590 0x0000 0x8 0x0
 #define MX6SX_PAD_SD2_DATA2__MMDC_DEBUG_32                        0x0248 0x0590 0x0000 0x9 0x0
 #define MX6SX_PAD_SD2_DATA3__USDHC2_DATA3                         0x024C 0x0594 0x0000 0x0 0x0
@@ -1320,12 +1340,13 @@
 #define MX6SX_PAD_SD2_DATA3__MLB_DATA                             0x024C 0x0594 0x07EC 0x4 0x2
 #define MX6SX_PAD_SD2_DATA3__GPIO6_IO_11                          0x024C 0x0594 0x0000 0x5 0x0
 #define MX6SX_PAD_SD2_DATA3__SPDIF_IN                             0x024C 0x0594 0x0824 0x6 0x4
-#define MX6SX_PAD_SD2_DATA3__UART6_RX                             0x024C 0x0594 0x0858 0x7 0x5
-#define MX6SX_PAD_SD2_DATA3__UART6_TX                             0x024C 0x0594 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA3__UART6_DCE_TX                         0x024C 0x0594 0x0000 0x7 0x0
+#define MX6SX_PAD_SD2_DATA3__UART6_DTE_RX                         0x024C 0x0594 0x0858 0x7 0x5
 #define MX6SX_PAD_SD2_DATA3__VADC_CLAMP_CURRENT_3                 0x024C 0x0594 0x0000 0x8 0x0
 #define MX6SX_PAD_SD2_DATA3__MMDC_DEBUG_31                        0x024C 0x0594 0x0000 0x9 0x0
 #define MX6SX_PAD_SD3_CLK__USDHC3_CLK                             0x0250 0x0598 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_CLK__UART4_CTS_B                            0x0250 0x0598 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CLK__UART4_DCE_CTS                          0x0250 0x0598 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CLK__UART4_DTE_RTS                          0x0250 0x0598 0x0844 0x1 0x0
 #define MX6SX_PAD_SD3_CLK__ECSPI4_SCLK                            0x0250 0x0598 0x0740 0x2 0x0
 #define MX6SX_PAD_SD3_CLK__AUDMUX_AUD6_RXFS                       0x0250 0x0598 0x0680 0x3 0x0
 #define MX6SX_PAD_SD3_CLK__LCDIF2_VSYNC                           0x0250 0x0598 0x0000 0x4 0x0
@@ -1334,8 +1355,8 @@
 #define MX6SX_PAD_SD3_CLK__TPSMP_HDATA_29                         0x0250 0x0598 0x0000 0x7 0x0
 #define MX6SX_PAD_SD3_CLK__SDMA_DEBUG_EVENT_CHANNEL_5             0x0250 0x0598 0x0000 0x9 0x0
 #define MX6SX_PAD_SD3_CMD__USDHC3_CMD                             0x0254 0x059C 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_CMD__UART4_RX                               0x0254 0x059C 0x0848 0x1 0x0
-#define MX6SX_PAD_SD3_CMD__UART4_TX                               0x0254 0x059C 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CMD__UART4_DCE_TX                           0x0254 0x059C 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_CMD__UART4_DTE_RX                           0x0254 0x059C 0x0848 0x1 0x0
 #define MX6SX_PAD_SD3_CMD__ECSPI4_MOSI                            0x0254 0x059C 0x0748 0x2 0x0
 #define MX6SX_PAD_SD3_CMD__AUDMUX_AUD6_RXC                        0x0254 0x059C 0x067C 0x3 0x0
 #define MX6SX_PAD_SD3_CMD__LCDIF2_HSYNC                           0x0254 0x059C 0x07E4 0x4 0x1
@@ -1364,7 +1385,8 @@
 #define MX6SX_PAD_SD3_DATA1__GPU_DEBUG_1                          0x025C 0x05A4 0x0000 0x8 0x0
 #define MX6SX_PAD_SD3_DATA1__SDMA_DEBUG_EVT_CHN_LINES_1           0x025C 0x05A4 0x0000 0x9 0x0
 #define MX6SX_PAD_SD3_DATA2__USDHC3_DATA2                         0x0260 0x05A8 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_DATA2__UART4_RTS_B                          0x0260 0x05A8 0x0844 0x1 0x1
+#define MX6SX_PAD_SD3_DATA2__UART4_DCE_RTS                        0x0260 0x05A8 0x0844 0x1 0x1
+#define MX6SX_PAD_SD3_DATA2__UART4_DTE_CTS                        0x0260 0x05A8 0x0000 0x1 0x0
 #define MX6SX_PAD_SD3_DATA2__ECSPI4_SS0                           0x0260 0x05A8 0x074C 0x2 0x0
 #define MX6SX_PAD_SD3_DATA2__AUDMUX_AUD6_TXFS                     0x0260 0x05A8 0x0688 0x3 0x0
 #define MX6SX_PAD_SD3_DATA2__LCDIF2_CLK                           0x0260 0x05A8 0x0000 0x4 0x0
@@ -1374,8 +1396,8 @@
 #define MX6SX_PAD_SD3_DATA2__GPU_DEBUG_2                          0x0260 0x05A8 0x0000 0x8 0x0
 #define MX6SX_PAD_SD3_DATA2__SDMA_DEBUG_EVENT_CHANNEL_2           0x0260 0x05A8 0x0000 0x9 0x0
 #define MX6SX_PAD_SD3_DATA3__USDHC3_DATA3                         0x0264 0x05AC 0x0000 0x0 0x0
-#define MX6SX_PAD_SD3_DATA3__UART4_RX                             0x0264 0x05AC 0x0848 0x1 0x1
-#define MX6SX_PAD_SD3_DATA3__UART4_TX                             0x0264 0x05AC 0x0000 0x1 0x0
+#define MX6SX_PAD_SD3_DATA3__UART4_DCE_RX                         0x0264 0x05AC 0x0848 0x1 0x1
+#define MX6SX_PAD_SD3_DATA3__UART4_DTE_TX                         0x0264 0x05AC 0x0000 0x1 0x0
 #define MX6SX_PAD_SD3_DATA3__ECSPI4_MISO                          0x0264 0x05AC 0x0744 0x2 0x0
 #define MX6SX_PAD_SD3_DATA3__AUDMUX_AUD6_TXD                      0x0264 0x05AC 0x0678 0x3 0x0
 #define MX6SX_PAD_SD3_DATA3__LCDIF2_ENABLE                        0x0264 0x05AC 0x0000 0x4 0x0
@@ -1387,8 +1409,8 @@
 #define MX6SX_PAD_SD3_DATA4__USDHC3_DATA4                         0x0268 0x05B0 0x0000 0x0 0x0
 #define MX6SX_PAD_SD3_DATA4__CAN2_RX                              0x0268 0x05B0 0x0690 0x1 0x0
 #define MX6SX_PAD_SD3_DATA4__CANFD_RX2                            0x0268 0x05B0 0x0698 0x2 0x0
-#define MX6SX_PAD_SD3_DATA4__UART3_RX                             0x0268 0x05B0 0x0840 0x3 0x2
-#define MX6SX_PAD_SD3_DATA4__UART3_TX                             0x0268 0x05B0 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA4__UART3_DCE_RX                         0x0268 0x05B0 0x0840 0x3 0x2
+#define MX6SX_PAD_SD3_DATA4__UART3_DTE_TX                         0x0268 0x05B0 0x0000 0x3 0x0
 #define MX6SX_PAD_SD3_DATA4__LCDIF2_DATA_3                        0x0268 0x05B0 0x0000 0x4 0x0
 #define MX6SX_PAD_SD3_DATA4__GPIO7_IO_6                           0x0268 0x05B0 0x0000 0x5 0x0
 #define MX6SX_PAD_SD3_DATA4__ENET2_1588_EVENT0_IN                 0x0268 0x05B0 0x0000 0x6 0x0
@@ -1398,8 +1420,8 @@
 #define MX6SX_PAD_SD3_DATA5__USDHC3_DATA5                         0x026C 0x05B4 0x0000 0x0 0x0
 #define MX6SX_PAD_SD3_DATA5__CAN1_TX                              0x026C 0x05B4 0x0000 0x1 0x0
 #define MX6SX_PAD_SD3_DATA5__CANFD_TX1                            0x026C 0x05B4 0x0000 0x2 0x0
-#define MX6SX_PAD_SD3_DATA5__UART3_RX                             0x026C 0x05B4 0x0840 0x3 0x3
-#define MX6SX_PAD_SD3_DATA5__UART3_TX                             0x026C 0x05B4 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA5__UART3_DCE_TX                         0x026C 0x05B4 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA5__UART3_DTE_RX                         0x026C 0x05B4 0x0840 0x3 0x3
 #define MX6SX_PAD_SD3_DATA5__LCDIF2_DATA_2                        0x026C 0x05B4 0x0000 0x4 0x0
 #define MX6SX_PAD_SD3_DATA5__GPIO7_IO_7                           0x026C 0x05B4 0x0000 0x5 0x0
 #define MX6SX_PAD_SD3_DATA5__ENET2_1588_EVENT0_OUT                0x026C 0x05B4 0x0000 0x6 0x0
@@ -1409,7 +1431,8 @@
 #define MX6SX_PAD_SD3_DATA6__USDHC3_DATA6                         0x0270 0x05B8 0x0000 0x0 0x0
 #define MX6SX_PAD_SD3_DATA6__CAN2_TX                              0x0270 0x05B8 0x0000 0x1 0x0
 #define MX6SX_PAD_SD3_DATA6__CANFD_TX2                            0x0270 0x05B8 0x0000 0x2 0x0
-#define MX6SX_PAD_SD3_DATA6__UART3_RTS_B                          0x0270 0x05B8 0x083C 0x3 0x2
+#define MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS                        0x0270 0x05B8 0x083C 0x3 0x2
+#define MX6SX_PAD_SD3_DATA6__UART3_DTE_CTS                        0x0270 0x05B8 0x0000 0x3 0x0
 #define MX6SX_PAD_SD3_DATA6__LCDIF2_DATA_4                        0x0270 0x05B8 0x0000 0x4 0x0
 #define MX6SX_PAD_SD3_DATA6__GPIO7_IO_8                           0x0270 0x05B8 0x0000 0x5 0x0
 #define MX6SX_PAD_SD3_DATA6__ENET1_1588_EVENT0_OUT                0x0270 0x05B8 0x0000 0x6 0x0
@@ -1419,7 +1442,8 @@
 #define MX6SX_PAD_SD3_DATA7__USDHC3_DATA7                         0x0274 0x05BC 0x0000 0x0 0x0
 #define MX6SX_PAD_SD3_DATA7__CAN1_RX                              0x0274 0x05BC 0x068C 0x1 0x0
 #define MX6SX_PAD_SD3_DATA7__CANFD_RX1                            0x0274 0x05BC 0x0694 0x2 0x0
-#define MX6SX_PAD_SD3_DATA7__UART3_CTS_B                          0x0274 0x05BC 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS                        0x0274 0x05BC 0x0000 0x3 0x0
+#define MX6SX_PAD_SD3_DATA7__UART3_DTE_RTS                        0x0274 0x05BC 0x083C 0x3 0x3
 #define MX6SX_PAD_SD3_DATA7__LCDIF2_DATA_5                        0x0274 0x05BC 0x0000 0x4 0x0
 #define MX6SX_PAD_SD3_DATA7__GPIO7_IO_9                           0x0274 0x05BC 0x0000 0x5 0x0
 #define MX6SX_PAD_SD3_DATA7__ENET1_1588_EVENT0_IN                 0x0274 0x05BC 0x0000 0x6 0x0
@@ -1488,8 +1512,8 @@
 #define MX6SX_PAD_SD4_DATA3__SDMA_DEBUG_MATCHED_DMBUS             0x028C 0x05D4 0x0000 0x9 0x0
 #define MX6SX_PAD_SD4_DATA4__USDHC4_DATA4                         0x0290 0x05D8 0x0000 0x0 0x0
 #define MX6SX_PAD_SD4_DATA4__RAWNAND_DATA09                       0x0290 0x05D8 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA4__UART5_RX                             0x0290 0x05D8 0x0850 0x2 0x0
-#define MX6SX_PAD_SD4_DATA4__UART5_TX                             0x0290 0x05D8 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA4__UART5_DCE_RX                         0x0290 0x05D8 0x0850 0x2 0x0
+#define MX6SX_PAD_SD4_DATA4__UART5_DTE_TX                         0x0290 0x05D8 0x0000 0x2 0x0
 #define MX6SX_PAD_SD4_DATA4__ECSPI3_SCLK                          0x0290 0x05D8 0x0730 0x3 0x0
 #define MX6SX_PAD_SD4_DATA4__LCDIF2_DATA_8                        0x0290 0x05D8 0x0000 0x4 0x0
 #define MX6SX_PAD_SD4_DATA4__GPIO6_IO_18                          0x0290 0x05D8 0x0000 0x5 0x0
@@ -1499,8 +1523,8 @@
 #define MX6SX_PAD_SD4_DATA4__SDMA_DEBUG_RTBUFFER_WRITE            0x0290 0x05D8 0x0000 0x9 0x0
 #define MX6SX_PAD_SD4_DATA5__USDHC4_DATA5                         0x0294 0x05DC 0x0000 0x0 0x0
 #define MX6SX_PAD_SD4_DATA5__RAWNAND_CE2_B                        0x0294 0x05DC 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA5__UART5_RX                             0x0294 0x05DC 0x0850 0x2 0x1
-#define MX6SX_PAD_SD4_DATA5__UART5_TX                             0x0294 0x05DC 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA5__UART5_DCE_TX                         0x0294 0x05DC 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA5__UART5_DTE_RX                         0x0294 0x05DC 0x0850 0x2 0x1
 #define MX6SX_PAD_SD4_DATA5__ECSPI3_MOSI                          0x0294 0x05DC 0x0738 0x3 0x0
 #define MX6SX_PAD_SD4_DATA5__LCDIF2_DATA_7                        0x0294 0x05DC 0x0000 0x4 0x0
 #define MX6SX_PAD_SD4_DATA5__GPIO6_IO_19                          0x0294 0x05DC 0x0000 0x5 0x0
@@ -1510,7 +1534,8 @@
 #define MX6SX_PAD_SD4_DATA5__SDMA_DEBUG_EVENT_CHANNEL_0           0x0294 0x05DC 0x0000 0x9 0x0
 #define MX6SX_PAD_SD4_DATA6__USDHC4_DATA6                         0x0298 0x05E0 0x0000 0x0 0x0
 #define MX6SX_PAD_SD4_DATA6__RAWNAND_CE3_B                        0x0298 0x05E0 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA6__UART5_RTS_B                          0x0298 0x05E0 0x084C 0x2 0x0
+#define MX6SX_PAD_SD4_DATA6__UART5_DCE_RTS                        0x0298 0x05E0 0x084C 0x2 0x0
+#define MX6SX_PAD_SD4_DATA6__UART5_DTE_CTS                        0x0298 0x05E0 0x0000 0x2 0x0
 #define MX6SX_PAD_SD4_DATA6__ECSPI3_MISO                          0x0298 0x05E0 0x0734 0x3 0x0
 #define MX6SX_PAD_SD4_DATA6__LCDIF2_DATA_6                        0x0298 0x05E0 0x0000 0x4 0x0
 #define MX6SX_PAD_SD4_DATA6__GPIO6_IO_20                          0x0298 0x05E0 0x0000 0x5 0x0
@@ -1520,7 +1545,8 @@
 #define MX6SX_PAD_SD4_DATA6__SDMA_DEBUG_EVENT_CHANNEL_1           0x0298 0x05E0 0x0000 0x9 0x0
 #define MX6SX_PAD_SD4_DATA7__USDHC4_DATA7                         0x029C 0x05E4 0x0000 0x0 0x0
 #define MX6SX_PAD_SD4_DATA7__RAWNAND_DATA08                       0x029C 0x05E4 0x0000 0x1 0x0
-#define MX6SX_PAD_SD4_DATA7__UART5_CTS_B                          0x029C 0x05E4 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA7__UART5_DCE_CTS                        0x029C 0x05E4 0x0000 0x2 0x0
+#define MX6SX_PAD_SD4_DATA7__UART5_DTE_RTS                        0x029C 0x05E4 0x084C 0x2 0x1
 #define MX6SX_PAD_SD4_DATA7__ECSPI3_SS0                           0x029C 0x05E4 0x073C 0x3 0x0
 #define MX6SX_PAD_SD4_DATA7__LCDIF2_DATA_15                       0x029C 0x05E4 0x0000 0x4 0x0
 #define MX6SX_PAD_SD4_DATA7__GPIO6_IO_21                          0x029C 0x05E4 0x0000 0x5 0x0
@@ -1551,4 +1577,92 @@
 #define MX6SX_PAD_USB_H_STROBE__WDOG3_WDOG_RST_B_DEB              0x02A8 0x05F0 0x0000 0x4 0x0
 #define MX6SX_PAD_USB_H_STROBE__GPIO7_IO_11                       0x02A8 0x05F0 0x0000 0x5 0x0
 
+/* these are not supposed to be used any more and remove them after some time */
+#define MX6SX_PAD_GPIO1_IO04__UART1_RX		MX6SX_PAD_GPIO1_IO04__UART1_DTE_RX
+#define MX6SX_PAD_GPIO1_IO04__UART1_TX		MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX
+#define MX6SX_PAD_GPIO1_IO05__UART1_RX		MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX
+#define MX6SX_PAD_GPIO1_IO05__UART1_TX		MX6SX_PAD_GPIO1_IO05__UART1_DTE_TX
+#define MX6SX_PAD_GPIO1_IO06__UART2_RX		MX6SX_PAD_GPIO1_IO06__UART2_DTE_RX
+#define MX6SX_PAD_GPIO1_IO06__UART2_TX		MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX
+#define MX6SX_PAD_GPIO1_IO06__UART1_RTS_B	MX6SX_PAD_GPIO1_IO06__UART1_DCE_RTS
+#define MX6SX_PAD_GPIO1_IO07__UART2_RX		MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX
+#define MX6SX_PAD_GPIO1_IO07__UART2_TX		MX6SX_PAD_GPIO1_IO07__UART2_DTE_TX
+#define MX6SX_PAD_GPIO1_IO07__UART1_CTS_B	MX6SX_PAD_GPIO1_IO07__UART1_DCE_CTS
+#define MX6SX_PAD_GPIO1_IO08__UART2_RTS_B	MX6SX_PAD_GPIO1_IO08__UART2_DCE_RTS
+#define MX6SX_PAD_GPIO1_IO09__UART2_CTS_B	MX6SX_PAD_GPIO1_IO09__UART2_DCE_CTS
+#define MX6SX_PAD_CSI_DATA04__UART6_RX		MX6SX_PAD_CSI_DATA04__UART6_DCE_RX
+#define MX6SX_PAD_CSI_DATA04__UART6_TX		MX6SX_PAD_CSI_DATA04__UART6_DTE_TX
+#define MX6SX_PAD_CSI_DATA05__UART6_RX		MX6SX_PAD_CSI_DATA05__UART6_DTE_RX
+#define MX6SX_PAD_CSI_DATA05__UART6_TX		MX6SX_PAD_CSI_DATA05__UART6_DCE_TX
+#define MX6SX_PAD_CSI_DATA06__UART6_RTS_B	MX6SX_PAD_CSI_DATA06__UART6_DCE_RTS
+#define MX6SX_PAD_CSI_DATA07__UART6_CTS_B	MX6SX_PAD_CSI_DATA07__UART6_DCE_CTS
+#define MX6SX_PAD_CSI_HSYNC__UART4_RTS_B	MX6SX_PAD_CSI_HSYNC__UART4_DCE_RTS
+#define MX6SX_PAD_CSI_MCLK__UART4_RX		MX6SX_PAD_CSI_MCLK__UART4_DCE_RX
+#define MX6SX_PAD_CSI_MCLK__UART4_TX		MX6SX_PAD_CSI_MCLK__UART4_DTE_TX
+#define MX6SX_PAD_CSI_PIXCLK__UART4_RX		MX6SX_PAD_CSI_PIXCLK__UART4_DTE_RX
+#define MX6SX_PAD_CSI_PIXCLK__UART4_TX		MX6SX_PAD_CSI_PIXCLK__UART4_DCE_TX
+#define MX6SX_PAD_CSI_VSYNC__UART4_CTS_B	MX6SX_PAD_CSI_VSYNC__UART4_DCE_CTS
+#define MX6SX_PAD_ENET2_COL__UART1_RX		MX6SX_PAD_ENET2_COL__UART1_DCE_RX
+#define MX6SX_PAD_ENET2_COL__UART1_TX		MX6SX_PAD_ENET2_COL__UART1_DTE_TX
+#define MX6SX_PAD_ENET2_CRS__UART1_RX		MX6SX_PAD_ENET2_CRS__UART1_DTE_RX
+#define MX6SX_PAD_ENET2_CRS__UART1_TX		MX6SX_PAD_ENET2_CRS__UART1_DCE_TX
+#define MX6SX_PAD_ENET2_RX_CLK__UART1_RTS_B	MX6SX_PAD_ENET2_RX_CLK__UART1_DCE_RTS
+#define MX6SX_PAD_ENET2_TX_CLK__UART1_CTS_B	MX6SX_PAD_ENET2_TX_CLK__UART1_DCE_CTS
+#define MX6SX_PAD_KEY_COL0__UART6_RTS_B		MX6SX_PAD_KEY_COL0__UART6_DCE_RTS
+#define MX6SX_PAD_KEY_COL1__UART6_RX		MX6SX_PAD_KEY_COL1__UART6_DTE_RX
+#define MX6SX_PAD_KEY_COL1__UART6_TX		MX6SX_PAD_KEY_COL1__UART6_DCE_TX
+#define MX6SX_PAD_KEY_COL2__UART5_RTS_B		MX6SX_PAD_KEY_COL2__UART5_DCE_RTS
+#define MX6SX_PAD_KEY_COL3__UART5_RX		MX6SX_PAD_KEY_COL3__UART5_DTE_RX
+#define MX6SX_PAD_KEY_COL3__UART5_TX		MX6SX_PAD_KEY_COL3__UART5_DCE_TX
+#define MX6SX_PAD_KEY_ROW0__UART6_CTS_B		MX6SX_PAD_KEY_ROW0__UART6_DCE_CTS
+#define MX6SX_PAD_KEY_ROW1__UART6_RX		MX6SX_PAD_KEY_ROW1__UART6_DCE_RX
+#define MX6SX_PAD_KEY_ROW1__UART6_TX		MX6SX_PAD_KEY_ROW1__UART6_DTE_TX
+#define MX6SX_PAD_KEY_ROW2__UART5_CTS_B		MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS
+#define MX6SX_PAD_KEY_ROW3__UART5_RX		MX6SX_PAD_KEY_ROW3__UART5_DCE_RX
+#define MX6SX_PAD_KEY_ROW3__UART5_TX		MX6SX_PAD_KEY_ROW3__UART5_DTE_TX
+#define MX6SX_PAD_NAND_DATA04__UART3_RTS_B	MX6SX_PAD_NAND_DATA04__UART3_DCE_RTS
+#define MX6SX_PAD_NAND_DATA05__UART3_CTS_B	MX6SX_PAD_NAND_DATA05__UART3_DCE_CTS
+#define MX6SX_PAD_NAND_DATA06__UART3_RX		MX6SX_PAD_NAND_DATA06__UART3_DCE_RX
+#define MX6SX_PAD_NAND_DATA06__UART3_TX		MX6SX_PAD_NAND_DATA06__UART3_DTE_TX
+#define MX6SX_PAD_NAND_DATA07__UART3_RX		MX6SX_PAD_NAND_DATA07__UART3_DTE_RX
+#define MX6SX_PAD_NAND_DATA07__UART3_TX		MX6SX_PAD_NAND_DATA07__UART3_DCE_TX
+#define MX6SX_PAD_QSPI1B_DATA0__UART3_CTS_B	MX6SX_PAD_QSPI1B_DATA0__UART3_DCE_CTS
+#define MX6SX_PAD_QSPI1B_DATA1__UART3_RTS_B	MX6SX_PAD_QSPI1B_DATA1__UART3_DCE_RTS
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_RX		MX6SX_PAD_QSPI1B_SCLK__UART3_DCE_RX
+#define MX6SX_PAD_QSPI1B_SCLK__UART3_TX		MX6SX_PAD_QSPI1B_SCLK__UART3_DTE_TX
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_RX	MX6SX_PAD_QSPI1B_SS0_B__UART3_DTE_RX
+#define MX6SX_PAD_QSPI1B_SS0_B__UART3_TX	MX6SX_PAD_QSPI1B_SS0_B__UART3_DCE_TX
+#define MX6SX_PAD_SD1_DATA0__UART2_RX		MX6SX_PAD_SD1_DATA0__UART2_DCE_RX
+#define MX6SX_PAD_SD1_DATA0__UART2_TX		MX6SX_PAD_SD1_DATA0__UART2_DTE_TX
+#define MX6SX_PAD_SD1_DATA1__UART2_RX		MX6SX_PAD_SD1_DATA1__UART2_DTE_RX
+#define MX6SX_PAD_SD1_DATA1__UART2_TX		MX6SX_PAD_SD1_DATA1__UART2_DCE_TX
+#define MX6SX_PAD_SD1_DATA2__UART2_CTS_B	MX6SX_PAD_SD1_DATA2__UART2_DCE_CTS
+#define MX6SX_PAD_SD1_DATA3__UART2_RTS_B	MX6SX_PAD_SD1_DATA3__UART2_DCE_RTS
+#define MX6SX_PAD_SD2_DATA0__UART4_RX		MX6SX_PAD_SD2_DATA0__UART4_DCE_RX
+#define MX6SX_PAD_SD2_DATA0__UART4_TX		MX6SX_PAD_SD2_DATA0__UART4_DTE_TX
+#define MX6SX_PAD_SD2_DATA1__UART4_RX		MX6SX_PAD_SD2_DATA1__UART4_DTE_RX
+#define MX6SX_PAD_SD2_DATA1__UART4_TX		MX6SX_PAD_SD2_DATA1__UART4_DCE_TX
+#define MX6SX_PAD_SD2_DATA2__UART6_RX		MX6SX_PAD_SD2_DATA2__UART6_DCE_RX
+#define MX6SX_PAD_SD2_DATA2__UART6_TX		MX6SX_PAD_SD2_DATA2__UART6_DTE_TX
+#define MX6SX_PAD_SD2_DATA3__UART6_RX		MX6SX_PAD_SD2_DATA3__UART6_DTE_RX
+#define MX6SX_PAD_SD2_DATA3__UART6_TX		MX6SX_PAD_SD2_DATA3__UART6_DCE_TX
+#define MX6SX_PAD_SD3_CLK__UART4_CTS_B		MX6SX_PAD_SD3_CLK__UART4_DCE_CTS
+#define MX6SX_PAD_SD3_CMD__UART4_RX		MX6SX_PAD_SD3_CMD__UART4_DTE_RX
+#define MX6SX_PAD_SD3_CMD__UART4_TX		MX6SX_PAD_SD3_CMD__UART4_DCE_TX
+#define MX6SX_PAD_SD3_DATA2__UART4_RTS_B	MX6SX_PAD_SD3_DATA2__UART4_DCE_RTS
+#define MX6SX_PAD_SD3_DATA3__UART4_RX		MX6SX_PAD_SD3_DATA3__UART4_DCE_RX
+#define MX6SX_PAD_SD3_DATA3__UART4_TX		MX6SX_PAD_SD3_DATA3__UART4_DTE_TX
+#define MX6SX_PAD_SD3_DATA4__UART3_RX		MX6SX_PAD_SD3_DATA4__UART3_DCE_RX
+#define MX6SX_PAD_SD3_DATA4__UART3_TX		MX6SX_PAD_SD3_DATA4__UART3_DTE_TX
+#define MX6SX_PAD_SD3_DATA5__UART3_RX		MX6SX_PAD_SD3_DATA5__UART3_DTE_RX
+#define MX6SX_PAD_SD3_DATA5__UART3_TX		MX6SX_PAD_SD3_DATA5__UART3_DCE_TX
+#define MX6SX_PAD_SD3_DATA6__UART3_RTS_B	MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS
+#define MX6SX_PAD_SD3_DATA7__UART3_CTS_B	MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS
+#define MX6SX_PAD_SD4_DATA4__UART5_RX		MX6SX_PAD_SD4_DATA4__UART5_DCE_RX
+#define MX6SX_PAD_SD4_DATA4__UART5_TX		MX6SX_PAD_SD4_DATA4__UART5_DTE_TX
+#define MX6SX_PAD_SD4_DATA5__UART5_RX		MX6SX_PAD_SD4_DATA5__UART5_DTE_RX
+#define MX6SX_PAD_SD4_DATA5__UART5_TX		MX6SX_PAD_SD4_DATA5__UART5_DCE_TX
+#define MX6SX_PAD_SD4_DATA6__UART5_RTS_B	MX6SX_PAD_SD4_DATA6__UART5_DCE_RTS
+#define MX6SX_PAD_SD4_DATA7__UART5_CTS_B	MX6SX_PAD_SD4_DATA7__UART5_DCE_CTS
+
 #endif /* __DTS_IMX6SX_PINFUNC_H */
diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sabreauto.dts
index 315044ccd65f..b0c27b9b0244 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sabreauto.dts
@@ -20,7 +20,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -66,12 +66,68 @@
 		enable-active-high;
 		vin-supply = <&reg_can_en>;
 	};
+
+	reg_cs42888: cs42888_supply {
+		compatible = "regulator-fixed";
+		regulator-name = "cs42888_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	sound-cs42888 {
+		compatible = "fsl,imx6-sabreauto-cs42888",
+			     "fsl,imx-audio-cs42888";
+		model = "imx-cs42888";
+		audio-cpu = <&esai>;
+		audio-asrc = <&asrc>;
+		audio-codec = <&cs42888>;
+		audio-routing =
+			"Line Out Jack", "AOUT1L",
+			"Line Out Jack", "AOUT1R",
+			"Line Out Jack", "AOUT2L",
+			"Line Out Jack", "AOUT2R",
+			"Line Out Jack", "AOUT3L",
+			"Line Out Jack", "AOUT3R",
+			"Line Out Jack", "AOUT4L",
+			"Line Out Jack", "AOUT4R",
+			"AIN1L", "Line In Jack",
+			"AIN1R", "Line In Jack",
+			"AIN2L", "Line In Jack",
+			"AIN2R", "Line In Jack";
+	};
+
+	sound-spdif {
+		compatible = "fsl,imx-audio-spdif";
+		model = "imx-spdif";
+		spdif-controller = <&spdif>;
+		spdif-in;
+	};
 };
 
 &anaclk2 {
 	clock-frequency = <24576000>;
 };
 
+&clks {
+	assigned-clocks = <&clks IMX6SX_PLL4_BYPASS_SRC>,
+			  <&clks IMX6SX_PLL4_BYPASS>,
+			  <&clks IMX6SX_CLK_PLL4_POST_DIV>;
+	assigned-clock-parents = <&clks IMX6SX_CLK_LVDS2_IN>,
+				 <&clks IMX6SX_PLL4_BYPASS_SRC>;
+	assigned-clock-rates = <0>, <0>, <24576000>;
+};
+
+&esai {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esai>;
+	assigned-clocks = <&clks IMX6SX_CLK_ESAI_SEL>,
+			<&clks IMX6SX_CLK_ESAI_EXTAL>;
+	assigned-clock-parents = <&clks IMX6SX_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <24576000>;
+	status = "okay";
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
@@ -99,7 +155,7 @@
 &fec2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet2>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
 	fsl,magic-packet;
 	status = "okay";
@@ -193,6 +249,21 @@
 		>;
 	};
 
+	pinctrl_esai: esaigrp {
+		fsl,pins = <
+			MX6SX_PAD_CSI_DATA00__ESAI_TX_CLK   0x1b030
+			MX6SX_PAD_CSI_DATA01__ESAI_TX_FS    0x1b030
+			MX6SX_PAD_CSI_HSYNC__ESAI_TX0       0x1b030
+			MX6SX_PAD_CSI_DATA04__ESAI_TX1      0x1b030
+			MX6SX_PAD_CSI_DATA06__ESAI_TX2_RX3  0x1b030
+			MX6SX_PAD_CSI_DATA07__ESAI_TX3_RX2  0x1b030
+			MX6SX_PAD_CSI_DATA02__ESAI_RX_CLK   0x1b030
+			MX6SX_PAD_CSI_DATA03__ESAI_RX_FS    0x1b030
+			MX6SX_PAD_CSI_VSYNC__ESAI_TX5_RX0   0x1b030
+			MX6SX_PAD_CSI_DATA05__ESAI_TX4_RX1  0x1b030
+		>;
+	};
+
 	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6SX_PAD_QSPI1B_DQS__CAN1_TX   0x1b020
@@ -227,10 +298,16 @@
 		>;
 	};
 
+	pinctrl_spdif: spdifgrp {
+		fsl,pins = <
+			MX6SX_PAD_ENET2_COL__SPDIF_IN           0x1b0b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
-			MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX		0x1b0b1
 		>;
 	};
 
@@ -313,6 +390,17 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
+	cs42888: cs42888@48 {
+		compatible = "cirrus,cs42888";
+		reg = <0x48>;
+		clocks = <&anaclk2 0>;
+		clock-names = "mclk";
+		VA-supply = <&reg_cs42888>;
+		VD-supply = <&reg_cs42888>;
+		VLS-supply = <&reg_cs42888>;
+		VLC-supply = <&reg_cs42888>;
+	};
+
 	touchscreen@4 {
 		compatible = "eeti,egalax_ts";
 		reg = <0x04>;
@@ -454,6 +542,14 @@
 	};
 };
 
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdif>;
+	assigned-clocks = <&clks IMX6SX_CLK_SPDIF_PODF>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dts
new file mode 100644
index 000000000000..a4ab2d3e960c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2014 Freescale Semiconductor, Inc.
+
+#include "imx6sx-sdb.dts"
+/ {
+
+	sound {
+		status = "disabled";
+	};
+
+	sound-mqs {
+		compatible = "fsl,imx6sx-sdb-mqs",
+			     "fsl,imx-audio-mqs";
+		model = "mqs-audio";
+		audio-cpu = <&sai1>;
+		audio-asrc = <&asrc>;
+		audio-codec = <&mqs>;
+	};
+};
+
+&usdhc2 {
+	/* pin conflict with mqs*/
+	status = "disabled";
+};
+
+&mqs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mqs>;
+	clocks = <&clks IMX6SX_CLK_SAI1>;
+	clock-names = "mclk";
+	status = "okay";
+};
+
+&sai1 {
+	pinctrl-0 = <>;
+	status = "okay";
+};
+
+&ssi2 {
+	status = "disabled";
+};
+
+&sdma {
+	gpr = <&gpr>;
+	/* SDMA event remap for SAI1 */
+	fsl,sdma-event-remap = <0 15 1>, <0 16 1>;
+};
diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-reva.dts
index f1830ed387a5..48f19dede467 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-reva.dts
@@ -6,6 +6,7 @@
 
 / {
 	model = "Freescale i.MX6 SoloX SDB RevA Board";
+	compatible = "fsl,imx6sx-sdb-reva", "fsl,imx6sx";
 };
 
 &i2c1 {
@@ -14,7 +15,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -122,7 +123,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: s25fl128s@0 {
+	flash0: flash@0 {
 		reg = <0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -132,7 +133,7 @@
 		spi-tx-bus-width = <4>;
 	};
 
-	flash1: s25fl128s@2 {
+	flash1: flash@2 {
 		reg = <2>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -159,10 +160,6 @@
 	vin-supply = <&vgen6_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
diff --git a/arch/arm/boot/dts/imx6sx-sdb-sai.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-sai.dts
index 1c4eacd68e1b..1c4eacd68e1b 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-sai.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-sai.dts
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dts
index a8ee7087af5a..e05a1be5553c 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dts
@@ -14,7 +14,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze200";
 		reg = <0x08>;
 
@@ -108,23 +108,23 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 
-	flash1: n25q256a@2 {
+	flash1: flash@2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <2>;
 	};
 };
@@ -141,10 +141,6 @@
 	vin-supply = <&vgen6_reg>;
 };
 
-&reg_vdd3p0 {
-	vin-supply = <&sw2_reg>;
-};
-
 &reg_vdd2p5 {
 	vin-supply = <&vgen6_reg>;
 };
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
index f6972deb5e39..c6e85e4a0883 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
@@ -153,6 +153,8 @@
 
 	sound {
 		compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
 		model = "wm8962-audio";
 		ssi-controller = <&ssi2>;
 		audio-codec = <&codec>;
@@ -165,6 +167,7 @@
 			"IN3R", "AMIC";
 		mux-int-port = <2>;
 		mux-ext-port = <6>;
+		hp-det-gpio = <&gpio1 17 GPIO_ACTIVE_LOW>;
 	};
 
 	panel {
@@ -179,6 +182,15 @@
 			};
 		};
 	};
+
+	sound-spdif {
+		compatible = "fsl,imx-audio-spdif",
+			   "fsl,imx6sx-sdb-spdif";
+		model = "imx-spdif";
+		spdif-controller = <&spdif>;
+		spdif-out;
+	};
+
 };
 
 &audmux {
@@ -194,6 +206,7 @@
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	fsl,magic-packet;
 	status = "okay";
 
 	mdio {
@@ -213,8 +226,9 @@
 &fec2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet2>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy2>;
+	fsl,magic-packet;
 	status = "okay";
 };
 
@@ -281,6 +295,7 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
@@ -296,6 +311,14 @@
 	status = "disabled";
 };
 
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdif>;
+	assigned-clocks = <&clks IMX6SX_CLK_SPDIF_PODF>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
 &ssi2 {
 	status = "okay";
 };
@@ -450,6 +473,12 @@
 			>;
 		};
 
+		pinctrl_hp: hpgrp {
+			fsl,pins = <
+				MX6SX_PAD_CSI_DATA03__GPIO1_IO_17 0x17059
+			>;
+		};
+
 		pinctrl_i2c1: i2c1grp {
 			fsl,pins = <
 				MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1
@@ -505,6 +534,13 @@
 			>;
 		};
 
+		pinctrl_mqs: mqsgrp {
+			fsl,pins = <
+				MX6SX_PAD_SD2_CLK__MQS_RIGHT 0x120b0
+				MX6SX_PAD_SD2_CMD__MQS_LEFT  0x120b0
+			>;
+		};
+
 		pinctrl_pcie: pciegrp {
 			fsl,pins = <
 				MX6SX_PAD_ENET1_COL__GPIO2_IO_0 0x10b0
@@ -562,19 +598,25 @@
 			>;
 		};
 
+		pinctrl_spdif: spdifgrp {
+			fsl,pins = <
+				MX6SX_PAD_SD4_DATA4__SPDIF_OUT          0x1b0b0
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
-				MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1
+				MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1
+				MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX	0x1b0b1
 			>;
 		};
 
 		pinctrl_uart5: uart5grp {
 			fsl,pins = <
-				MX6SX_PAD_KEY_ROW3__UART5_RX		0x1b0b1
-				MX6SX_PAD_KEY_COL3__UART5_TX		0x1b0b1
-				MX6SX_PAD_KEY_ROW2__UART5_CTS_B		0x1b0b1
-				MX6SX_PAD_KEY_COL2__UART5_RTS_B		0x1b0b1
+				MX6SX_PAD_KEY_ROW3__UART5_DCE_RX	0x1b0b1
+				MX6SX_PAD_KEY_COL3__UART5_DCE_TX	0x1b0b1
+				MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS	0x1b0b1
+				MX6SX_PAD_KEY_COL2__UART5_DCE_RTS	0x1b0b1
 			>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
index 28563f21024e..bfcd8f7d86dd 100644
--- a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
@@ -40,22 +40,22 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		red {
+		led-1 {
 			label = "red";
 			max-brightness = <255>;
 			pwms = <&pwm6 0 50000>;
 		};
 
-		green {
+		led-2 {
 			label = "green";
 			max-brightness = <255>;
 			pwms = <&pwm2 0 50000>;
 		};
 
-		blue {
+		led-3 {
 			label = "blue";
 			max-brightness = <255>;
 			pwms = <&pwm1 0 50000>;
@@ -93,7 +93,7 @@
 &ecspi4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
-	cs-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -171,7 +171,7 @@
 		reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
 	};
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze200";
 		reg = <0x08>;
 
@@ -352,6 +352,12 @@
 		>;
 	};
 
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_DATA02__GPIO4_IO_6	0x10b0
+		>;
+	};
+
 	pinctrl_pwm1: pwm1grp-1 {
 		fsl,pins = <
 			/* blue LED */
@@ -384,15 +390,15 @@
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
-			MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX	0x1b0b1
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX6SX_PAD_GPIO1_IO06__UART2_TX		0x1b0b1
-			MX6SX_PAD_GPIO1_IO07__UART2_RX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX	0x1b0b1
+			MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX	0x1b0b1
 		>;
 	};
 
@@ -490,19 +496,30 @@
 	};
 };
 
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+	status = "okay";
+};
+
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
 };
 
 &pwm6 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm6>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo-basic.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-basic.dts
index 205ea26484e3..205ea26484e3 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo-basic.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-basic.dts
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo-extended.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-extended.dts
index 5817b4985391..5817b4985391 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo-extended.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-extended.dts
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo-full.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-full.dts
index 96f4d89848a3..96f4d89848a3 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo-full.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-full.dts
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo.dtsi
index 25d4aa985a69..725d0b5cb55f 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo.dtsi
@@ -15,14 +15,14 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-red {
 			label = "udoo-neo:red:mmc";
 			gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "mmc0";
 		};
 
-		orange {
+		led-orange {
 			label = "udoo-neo:orange:user";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -183,6 +183,27 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	hdmi-transmitter@70 {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+		interrupts-extended = <&gpio3 27 IRQ_TYPE_LEVEL_LOW>;
+
+		ports {
+			port {
+				hdmi: endpoint {
+					remote-endpoint = <&lcdc>;
+				};
+			};
+		};
+	};
+};
+
 &i2c4 { /* Onboard Motion sensors */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c4>;
@@ -190,10 +211,22 @@
 	status = "disabled";
 };
 
+&lcdif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcd>;
+	status = "okay";
+
+	port {
+		lcdc: endpoint {
+			remote-endpoint = <&hdmi>;
+		};
+	};
+};
+
 &iomuxc {
 	pinctrl_bt_reg: btreggrp {
 		fsl,pins =
-			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17        0x15059>;
+			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17	0x15059>;
 	};
 
 	pinctrl_enet1: enet1grp {
@@ -227,36 +260,76 @@
 			<MX6SX_PAD_GPIO1_IO02__I2C2_SCL		0x4001b8b1>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX6SX_PAD_KEY_ROW4__I2C3_SDA			0x4001b8b1>,
+			<MX6SX_PAD_KEY_COL4__I2C3_SCL			0x4001b8b1>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins =
 			<MX6SX_PAD_USB_H_DATA__I2C4_SDA		0x4001b8b1>,
 			<MX6SX_PAD_USB_H_STROBE__I2C4_SCL	0x4001b8b1>;
 	};
 
+	pinctrl_lcd: lcdgrp {
+		fsl,pins = <
+			MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23		0x4001b0b0
+			MX6SX_PAD_LCD1_CLK__LCDIF1_CLK		0x4001b0b0
+			MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE		0x4001b0b0
+			MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC		0x4001b0b0
+			MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC		0x4001b0b0
+			MX6SX_PAD_LCD1_RESET__GPIO3_IO_27		0x4001b0b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1>,
-			<MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1>;
+			<MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1>,
+			<MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX	0x1b0b1>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO06__UART2_TX		0x1b0b1>,
-			<MX6SX_PAD_GPIO1_IO07__UART2_RX		0x1b0b1>;
+			<MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX	0x1b0b1>,
+			<MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX	0x1b0b1>;
 	};
 
 	pinctrl_uart3: uart3grp {
 		fsl,pins =
-			<MX6SX_PAD_SD3_DATA4__UART3_RX          0x13059>,
-			<MX6SX_PAD_SD3_DATA5__UART3_TX          0x13059>,
-			<MX6SX_PAD_SD3_DATA6__UART3_RTS_B       0x13059>,
-			<MX6SX_PAD_SD3_DATA7__UART3_CTS_B       0x13059>;
+			<MX6SX_PAD_SD3_DATA4__UART3_DCE_RX	0x13059>,
+			<MX6SX_PAD_SD3_DATA5__UART3_DCE_TX	0x13059>,
+			<MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS	0x13059>,
+			<MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS	0x13059>;
 	};
 
 	pinctrl_uart5: uart5grp {
 		fsl,pins =
-			<MX6SX_PAD_SD4_DATA4__UART5_RX		0x1b0b1>,
-			<MX6SX_PAD_SD4_DATA5__UART5_TX		0x1b0b1>;
+			<MX6SX_PAD_SD4_DATA4__UART5_DCE_RX	0x1b0b1>,
+			<MX6SX_PAD_SD4_DATA5__UART5_DCE_TX	0x1b0b1>;
 	};
 
 	pinctrl_uart6: uart6grp {
@@ -265,32 +338,31 @@
 			<MX6SX_PAD_CSI_DATA01__UART6_DSR_B	0x1b0b1>,
 			<MX6SX_PAD_CSI_DATA02__UART6_DTR_B	0x1b0b1>,
 			<MX6SX_PAD_CSI_DATA03__UART6_DCD_B	0x1b0b1>,
-			<MX6SX_PAD_CSI_DATA04__UART6_RX		0x1b0b1>,
-			<MX6SX_PAD_CSI_DATA05__UART6_TX		0x1b0b1>,
-			<MX6SX_PAD_CSI_DATA06__UART6_RTS_B	0x1b0b1>,
-			<MX6SX_PAD_CSI_DATA07__UART6_CTS_B	0x1b0b1>;
+			<MX6SX_PAD_CSI_DATA04__UART6_DCE_RX	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA05__UART6_DCE_TX	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA06__UART6_DCE_RTS	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA07__UART6_DCE_CTS	0x1b0b1>;
 	};
 
 	pinctrl_otg1_reg: otg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9        0x10b0>;
+			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0>;
 	};
 
-
 	pinctrl_otg2_reg: otg2grp {
 		fsl,pins =
-			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12        0x10b0>;
+			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12	0x10b0>;
 	};
 
 	pinctrl_usb_otg1: usbotg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID    0x17059>,
-			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC       0x10b0>;
+			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059>,
+			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC	0x10b0>;
 	};
 
 	pinctrl_usb_otg2: usbot2ggrp {
 		fsl,pins =
-			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC     0x10b0>;
+			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC	0x10b0>;
 	};
 
 	pinctrl_usdhc2: usdhc2grp {
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index 59bad60a47dc..df3a375f0a3e 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -49,6 +49,9 @@
 		spi2 = &ecspi3;
 		spi3 = &ecspi4;
 		spi4 = &ecspi5;
+		usb0 = &usbotg1;
+		usb1 = &usbotg2;
+		usb2 = &usbh;
 		usbphy0 = &usbphy1;
 		usbphy1 = &usbphy2;
 	};
@@ -87,6 +90,8 @@
 				      "pll1_sw", "pll1_sys";
 			arm-supply = <&reg_arm>;
 			soc-supply = <&reg_soc>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 	};
 
@@ -132,14 +137,10 @@
 		clock-output-names = "anaclk2";
 	};
 
-	tempmon: tempmon {
-		compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
-		interrupt-parent = <&gpc>;
-		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-		fsl,tempmon = <&anatop>;
-		nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
-		nvmem-cell-names = "calib", "temp_grade";
-		clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+	mqs: mqs {
+		compatible = "fsl,imx6sx-mqs";
+		gpr = <&gpr>;
+		status = "disabled";
 	};
 
 	pmu {
@@ -153,7 +154,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -163,12 +164,18 @@
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
@@ -181,7 +188,7 @@
 			interrupt-parent = <&intc>;
 		};
 
-		L2: l2-cache@a02000 {
+		L2: cache-controller@a02000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x00a02000 0x1000>;
 			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
@@ -202,20 +209,19 @@
 			power-domains = <&pd_pu>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX6SX_CLK_APBH_DMA>;
 		};
 
-		gpmi: gpmi-nand@1806000{
+		gpmi: nand-controller@1806000 {
 			compatible = "fsl,imx6sx-gpmi-nand";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -235,7 +241,7 @@
 			status = "disabled";
 		};
 
-		aips1: aips-bus@2000000 {
+		aips1: bus@2000000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -333,6 +339,7 @@
 				};
 
 				esai: esai@2024000 {
+					compatible = "fsl,imx6sx-esai", "fsl,imx35-esai";
 					reg = <0x02024000 0x4000>;
 					interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SX_CLK_ESAI_IPG>,
@@ -342,6 +349,9 @@
 						 <&clks IMX6SX_CLK_SPBA>;
 					clock-names = "core", "mem", "extal",
 						      "fsys", "spba";
+					dmas = <&sdma 23 21 0>,
+					       <&sdma 24 21 0>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -388,18 +398,28 @@
 				};
 
 				asrc: asrc@2034000 {
+					compatible = "fsl,imx6sx-asrc", "fsl,imx53-asrc";
 					reg = <0x02034000 0x4000>;
 					interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-					clocks = <&clks IMX6SX_CLK_ASRC_MEM>,
-						 <&clks IMX6SX_CLK_ASRC_IPG>,
-						 <&clks IMX6SX_CLK_SPDIF>,
-						 <&clks IMX6SX_CLK_SPBA>;
-					clock-names = "mem", "ipg", "asrck", "spba";
-					dmas = <&sdma 17 20 1>, <&sdma 18 20 1>,
-					       <&sdma 19 20 1>, <&sdma 20 20 1>,
-					       <&sdma 21 20 1>, <&sdma 22 20 1>;
+					clocks = <&clks IMX6SX_CLK_ASRC_IPG>,
+						<&clks IMX6SX_CLK_ASRC_MEM>, <&clks 0>,
+						<&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+						<&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+						<&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+						<&clks IMX6SX_CLK_SPDIF>, <&clks 0>, <&clks 0>,
+						<&clks IMX6SX_CLK_SPBA>;
+					clock-names = "mem", "ipg", "asrck_0",
+						"asrck_1", "asrck_2", "asrck_3", "asrck_4",
+						"asrck_5", "asrck_6", "asrck_7", "asrck_8",
+						"asrck_9", "asrck_a", "asrck_b", "asrck_c",
+						"asrck_d", "asrck_e", "asrck_f", "spba";
+					dmas = <&sdma 17 23 1>, <&sdma 18 23 1>,
+					       <&sdma 19 23 1>, <&sdma 20 23 1>,
+					       <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 						    "txa", "txb", "txc";
+					fsl,asrc-rate = <48000>;
+					fsl,asrc-width = <16>;
 					status = "okay";
 				};
 			};
@@ -411,7 +431,7 @@
 				clocks = <&clks IMX6SX_CLK_PWM1>,
 					 <&clks IMX6SX_CLK_PWM1>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm2: pwm@2084000 {
@@ -421,7 +441,7 @@
 				clocks = <&clks IMX6SX_CLK_PWM2>,
 					 <&clks IMX6SX_CLK_PWM2>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm3: pwm@2088000 {
@@ -431,7 +451,7 @@
 				clocks = <&clks IMX6SX_CLK_PWM3>,
 					 <&clks IMX6SX_CLK_PWM3>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm4: pwm@208c000 {
@@ -441,7 +461,7 @@
 				clocks = <&clks IMX6SX_CLK_PWM4>,
 					 <&clks IMX6SX_CLK_PWM4>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			flexcan1: can@2090000 {
@@ -451,7 +471,7 @@
 				clocks = <&clks IMX6SX_CLK_CAN1_IPG>,
 					 <&clks IMX6SX_CLK_CAN1_SERIAL>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x10 1 0x10 17>;
+				fsl,stop-mode = <&gpr 0x10 1>;
 				status = "disabled";
 			};
 
@@ -462,11 +482,11 @@
 				clocks = <&clks IMX6SX_CLK_CAN2_IPG>,
 					 <&clks IMX6SX_CLK_CAN2_SERIAL>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x10 2 0x10 18>;
+				fsl,stop-mode = <&gpr 0x10 2>;
 				status = "disabled";
 			};
 
-			gpt: gpt@2098000 {
+			gpt: timer@2098000 {
 				compatible = "fsl,imx6sx-gpt", "fsl,imx6dl-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -559,7 +579,7 @@
 				gpio-ranges = <&iomuxc 0 148 10>, <&iomuxc 10 169 2>;
 			};
 
-			kpp: kpp@20b8000 {
+			kpp: keypad@20b8000 {
 				compatible = "fsl,imx6sx-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -567,14 +587,14 @@
 				status = "disabled";
 			};
 
-			wdog1: wdog@20bc000 {
+			wdog1: watchdog@20bc000 {
 				compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt";
 				reg = <0x020bc000 0x4000>;
 				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_IPG>;
 			};
 
-			wdog2: wdog@20c0000 {
+			wdog2: watchdog@20c0000 {
 				compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt";
 				reg = <0x020c0000 0x4000>;
 				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
@@ -582,7 +602,7 @@
 				status = "disabled";
 			};
 
-			clks: ccm@20c4000 {
+			clks: clock-controller@20c4000 {
 				compatible = "fsl,imx6sx-ccm";
 				reg = <0x020c4000 0x4000>;
 				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
@@ -694,6 +714,16 @@
 					anatop-min-voltage = <725000>;
 					anatop-max-voltage = <1450000>;
 				};
+
+				tempmon: tempmon {
+					compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
+					interrupt-parent = <&gpc>;
+					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+					fsl,tempmon = <&anatop>;
+					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+					nvmem-cell-names = "calib", "temp_grade";
+					clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+				};
 			};
 
 			usbphy1: usbphy@20c9000 {
@@ -752,7 +782,7 @@
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6sx-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -806,18 +836,47 @@
 				};
 			};
 
-			iomuxc: iomuxc@20e0000 {
+			iomuxc: pinctrl@20e0000 {
 				compatible = "fsl,imx6sx-iomuxc";
 				reg = <0x020e0000 0x4000>;
 			};
 
-			gpr: iomuxc-gpr@20e4000 {
+			gpr: syscon@20e4000 {
 				compatible = "fsl,imx6sx-iomuxc-gpr",
-					     "fsl,imx6q-iomuxc-gpr", "syscon";
+					     "fsl,imx6q-iomuxc-gpr", "syscon", "simple-mfd";
+				#address-cells = <1>;
+				#size-cells = <1>;
 				reg = <0x020e4000 0x4000>;
+
+				lvds_bridge: bridge@18 {
+					compatible = "fsl,imx6sx-ldb";
+					reg = <0x18 0x4>;
+					clocks = <&clks IMX6SX_CLK_LDB_DI0>;
+					clock-names = "ldb";
+					status = "disabled";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							ldb_from_lcdif1: endpoint {
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							ldb_lvds_ch0: endpoint {
+							};
+						};
+					};
+				};
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sx-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -830,14 +889,14 @@
 			};
 		};
 
-		aips2: aips-bus@2100000 {
+		aips2: bus@2100000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x02100000 0x100000>;
 			ranges;
 
-			crypto: caam@2100000 {
+			crypto: crypto@2100000 {
 				compatible = "fsl,sec-v4.0";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -850,13 +909,13 @@
 					 <&clks IMX6SX_CLK_EIM_SLOW>;
 				clock-names = "mem", "aclk", "ipg", "emi_slow";
 
-				sec_jr0: jr0@1000 {
+				sec_jr0: jr@1000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr1: jr1@2000 {
+				sec_jr1: jr@2000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x2000 0x1000>;
 					interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
@@ -928,6 +987,7 @@
 					      "enet_clk_ref", "enet_out";
 				fsl,num-tx-queues = <3>;
 				fsl,num-rx-queues = <3>;
+				fsl,stop-mode = <&gpr 0x10 3>;
 				status = "disabled";
 			};
 
@@ -940,7 +1000,7 @@
 				status = "disabled";
 			};
 
-			usdhc1: usdhc@2190000 {
+			usdhc1: mmc@2190000 {
 				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -949,10 +1009,12 @@
 					 <&clks IMX6SX_CLK_USDHC1>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
-			usdhc2: usdhc@2194000 {
+			usdhc2: mmc@2194000 {
 				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -961,10 +1023,12 @@
 					 <&clks IMX6SX_CLK_USDHC2>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
-			usdhc3: usdhc@2198000 {
+			usdhc3: mmc@2198000 {
 				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x02198000 0x4000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
@@ -973,10 +1037,12 @@
 					 <&clks IMX6SX_CLK_USDHC3>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
-			usdhc4: usdhc@219c000 {
+			usdhc4: mmc@219c000 {
 				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x0219c000 0x4000>;
 				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
@@ -1037,6 +1103,7 @@
 					 <&clks IMX6SX_CLK_ENET_PTP>;
 				clock-names = "ipg", "ahb", "ptp",
 					      "enet_clk_ref", "enet_out";
+				fsl,stop-mode = <&gpr 0x10 4>;
 				status = "disabled";
 			};
 
@@ -1051,13 +1118,17 @@
 				status = "disabled";
 			};
 
-			ocotp: ocotp@21bc000 {
+			ocotp: efuse@21bc000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6sx-ocotp", "syscon";
 				reg = <0x021bc000 0x4000>;
 				clocks = <&clks IMX6SX_CLK_OCOTP>;
 
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
+
 				tempmon_calib: calib@38 {
 					reg = <0x38 4>;
 				};
@@ -1188,7 +1259,7 @@
 			};
 		};
 
-		aips3: aips-bus@2200000 {
+		aips3: bus@2200000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1240,8 +1311,17 @@
 						 <&clks IMX6SX_CLK_LCDIF_APB>,
 						 <&clks IMX6SX_CLK_DISPLAY_AXI>;
 					clock-names = "pix", "axi", "disp_axi";
+					assigned-clocks = <&clks IMX6SX_CLK_LCDIF1_PRE_SEL>,
+							  <&clks IMX6SX_CLK_LCDIF1_SEL>;
+					assigned-clock-parents = <&clks IMX6SX_CLK_PLL5_VIDEO_DIV>,
+								 <&clks IMX6SX_CLK_LCDIF1_PODF>;
 					power-domains = <&pd_disp>;
 					status = "disabled";
+
+					port {
+						lcdif1_to_ldb: endpoint {
+						};
+					};
 				};
 
 				lcdif2: lcdif@2224000 {
@@ -1289,7 +1369,7 @@
 				status = "disabled";
 			};
 
-			wdog3: wdog@2288000 {
+			wdog3: watchdog@2288000 {
 				compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt";
 				reg = <0x02288000 0x4000>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
@@ -1329,7 +1409,7 @@
 				clocks = <&clks IMX6SX_CLK_PWM5>,
 					 <&clks IMX6SX_CLK_PWM5>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm6: pwm@22a8000 {
@@ -1339,7 +1419,7 @@
 				clocks = <&clks IMX6SX_CLK_PWM6>,
 					 <&clks IMX6SX_CLK_PWM6>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm7: pwm@22ac000 {
@@ -1349,30 +1429,30 @@
 				clocks = <&clks IMX6SX_CLK_PWM7>,
 					 <&clks IMX6SX_CLK_PWM7>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 
 			pwm8: pwm@22b0000 {
 				compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
-				reg = <0x0022b0000 0x4000>;
+				reg = <0x022b0000 0x4000>;
 				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_PWM8>,
 					 <&clks IMX6SX_CLK_PWM8>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 			};
 		};
 
 		pcie: pcie@8ffc000 {
-			compatible = "fsl,imx6sx-pcie", "snps,dw-pcie";
+			compatible = "fsl,imx6sx-pcie";
 			reg = <0x08ffc000 0x04000>, <0x08f00000 0x80000>;
 			reg-names = "dbi", "config";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
 			bus-range = <0x00 0xff>;
-			ranges = <0x81000000 0 0          0x08f80000 0 0x00010000 /* downstream I/O */
-				  0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0 0          0x08f80000 0 0x00010000>, /* downstream I/O */
+				 <0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
 			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dts
index 2438669f149a..2438669f149a 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dts
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
index 1506eb12b21e..2ac40d69425b 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
@@ -2,6 +2,8 @@
 //
 // Copyright (C) 2015 Freescale Semiconductor, Inc.
 
+#include <dt-bindings/media/video-interfaces.h>
+
 / {
 	chosen {
 		stdout-path = &uart1;
@@ -30,14 +32,26 @@
 		enable-active-high;
 	};
 
-	reg_sensors: regulator-sensors {
+	reg_peri_3v3: regulator-peri-3v3 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_sensors_reg>;
-		regulator-name = "sensors-supply";
+		pinctrl-0 = <&pinctrl_peri_3v3>;
+		regulator-name = "VPERI_3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio5 2 GPIO_ACTIVE_LOW>;
+		/*
+		 * If you want to want to make this dynamic please
+		 * check schematics and test all affected peripherals:
+		 *
+		 * - sensors
+		 * - ethernet phy
+		 * - can
+		 * - bluetooth
+		 * - wm8960 audio codec
+		 * - ov5640 camera
+		 */
+		regulator-always-on;
 	};
 
 	reg_can_3v3: regulator-can-3v3 {
@@ -48,48 +62,36 @@
 		gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>;
 	};
 
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "mx6ul-wm8960";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink_master>;
-		simple-audio-card,frame-master = <&dailink_master>;
-		simple-audio-card,widgets =
-			"Microphone", "Mic Jack",
-			"Line", "Line In",
-			"Line", "Line Out",
-			"Speaker", "Speaker",
-			"Headphone", "Headphone Jack";
-		simple-audio-card,routing =
+	sound-wm8960 {
+		compatible = "fsl,imx-audio-wm8960";
+		model = "wm8960-audio";
+		audio-cpu = <&sai2>;
+		audio-codec = <&codec>;
+		audio-asrc = <&asrc>;
+		hp-det-gpio = <&gpio5 4 0>;
+		audio-routing =
 			"Headphone Jack", "HP_L",
 			"Headphone Jack", "HP_R",
-			"Speaker", "SPK_LP",
-			"Speaker", "SPK_LN",
-			"Speaker", "SPK_RP",
-			"Speaker", "SPK_RN",
-			"LINPUT1", "Mic Jack",
+			"Ext Spk", "SPK_LP",
+			"Ext Spk", "SPK_LN",
+			"Ext Spk", "SPK_RP",
+			"Ext Spk", "SPK_RN",
+			"LINPUT2", "Mic Jack",
 			"LINPUT3", "Mic Jack",
-			"RINPUT1", "Mic Jack",
-			"RINPUT2", "Mic Jack";
-
-		simple-audio-card,cpu {
-			sound-dai = <&sai2>;
-		};
-
-		dailink_master: simple-audio-card,codec {
-			sound-dai = <&codec>;
-			clocks = <&clks IMX6UL_CLK_SAI2>;
-		};
+			"RINPUT1", "AMIC",
+			"RINPUT2", "AMIC",
+			"Mic Jack", "MICB",
+			"AMIC", "MICB";
 	};
 
-	spi4 {
+	spi-4 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi4>;
 		status = "okay";
-		gpio-sck = <&gpio5 11 0>;
-		gpio-mosi = <&gpio5 10 0>;
-		cs-gpios = <&gpio5 7 0>;
+		sck-gpios = <&gpio5 11 0>;
+		mosi-gpios = <&gpio5 10 0>;
+		cs-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -101,6 +103,7 @@
 			reg = <0>;
 			registers-number = <1>;
 			spi-max-frequency = <100000>;
+			enable-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -132,6 +135,45 @@
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
 		wlf,shared-lrclk;
+		wlf,hp-cfg = <3 2 3>;
+		wlf,gpio-cfg = <1 3>;
+		clocks = <&clks IMX6UL_CLK_SAI2>;
+		clock-names = "mclk";
+	};
+
+	camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_camera_clock>;
+		clocks = <&clks IMX6UL_CLK_CSI>;
+		clock-names = "xclk";
+		powerdown-gpios = <&gpio_spi 6 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio_spi 5 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5640_to_parallel: endpoint {
+				remote-endpoint = <&parallel_from_ov5640>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <0>;
+				vsync-active = <0>;
+				pclk-sample = <1>;
+			};
+		};
+	};
+};
+
+&csi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_csi1>;
+	status = "okay";
+
+	port {
+		parallel_from_ov5640: endpoint {
+			remote-endpoint = <&ov5640_to_parallel>;
+			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
+		};
 	};
 };
 
@@ -140,6 +182,7 @@
 	pinctrl-0 = <&pinctrl_enet1>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_peri_3v3>;
 	status = "okay";
 };
 
@@ -148,6 +191,7 @@
 	pinctrl-0 = <&pinctrl_enet2>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_peri_3v3>;
 	status = "okay";
 
 	mdio {
@@ -155,13 +199,16 @@
 		#size-cells = <0>;
 
 		ethphy0: ethernet-phy@2 {
+			compatible = "ethernet-phy-id0022.1560";
 			reg = <2>;
 			micrel,led-mode = <1>;
 			clocks = <&clks IMX6UL_CLK_ENET_REF>;
 			clock-names = "rmii-ref";
+
 		};
 
 		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0022.1560";
 			reg = <1>;
 			micrel,led-mode = <1>;
 			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
@@ -184,6 +231,22 @@
 	status = "okay";
 };
 
+&gpio_spi {
+	eth0-phy-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "eth0-phy";
+	};
+
+	eth1-phy-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "eth1-phy";
+	};
+};
+
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -193,8 +256,8 @@
 	magnetometer@e {
 		compatible = "fsl,mag3110";
 		reg = <0x0e>;
-		vdd-supply = <&reg_sensors>;
-		vddio-supply = <&reg_sensors>;
+		vdd-supply = <&reg_peri_3v3>;
+		vddio-supply = <&reg_peri_3v3>;
 	};
 };
 
@@ -214,6 +277,7 @@
 };
 
 &pwm1 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -224,13 +288,13 @@
 	pinctrl-0 = <&pinctrl_qspi>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "micron,n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 };
@@ -313,6 +377,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	no-1-8-v;
+	broken-cd;
 	keep-power-in-suspend;
 	wakeup-source;
 	status = "okay";
@@ -327,9 +392,14 @@
 &iomuxc {
 	pinctrl-names = "default";
 
-	pinctrl_csi1: csi1grp {
+	pinctrl_camera_clock: cameraclockgrp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_MCLK__CSI_MCLK		0x1b088
+		>;
+	};
+
+	pinctrl_csi1: csi1grp {
+		fsl,pins = <
 			MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK	0x1b088
 			MX6UL_PAD_CSI_VSYNC__CSI_VSYNC		0x1b088
 			MX6UL_PAD_CSI_HSYNC__CSI_HSYNC		0x1b088
@@ -372,14 +442,14 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1grp{
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
 			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2grp{
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
 			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
@@ -462,7 +532,7 @@
 		>;
 	};
 
-	pinctrl_sensors_reg: sensorsreggrp {
+	pinctrl_peri_3v3: peri3v3grp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0
 		>;
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcexpress.dts
index 3792679c0c90..ad7f63ca521a 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcexpress.dts
@@ -145,7 +145,7 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1grp{
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA08__FLEXCAN1_TX	0x1b020
 			MX6UL_PAD_LCD_DATA09__FLEXCAN1_RX	0x1b020
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
index 3749fdda3611..1762bc47e18d 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
@@ -25,7 +25,7 @@
 	};
 
 	panel {
-		compatible = "auo,g101evn010", "simple-panel";
+		compatible = "auo,g101evn010";
 		power-supply = <&ldo4_ext>;
 		backlight = <&lcd_backlight>;
 
@@ -110,7 +110,7 @@
 };
 
 &gpio5 {
-	emmc-usd-mux {
+	emmc-usd-mux-hog {
 		gpio-hog;
 		gpios = <1 GPIO_ACTIVE_LOW>;
 		output-high;
@@ -168,6 +168,7 @@
 };
 
 &pwm5 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm5>;
 	status = "okay";
@@ -290,20 +291,20 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1grp{
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
 			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
 		>;
 	};
-	pinctrl_flexcan2: flexcan2grp{
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
 			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
 		>;
 	};
 
-	pinctrl_goodix_touch: goodixgrp{
+	pinctrl_goodix_touch: goodixgrp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1020
 		>;
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsom.dtsi
index b5781c3656d1..4a03ea6d24dc 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsom.dtsi
@@ -114,7 +114,6 @@
 			};
 
 			vdda_adc_3v3: vldo1 {
-				compatible = "regulator-fixed";
 				regulator-name = "vref-adc-3v3";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -158,7 +157,7 @@
 				regulator-max-microvolt = <3300000>;
 			};
 
-			vcoin_chg: vcoin {
+			vcoin_chg: coin {
 				regulator-min-microvolt = <2500000>;
 				regulator-max-microvolt = <3300000>;
 			};
diff --git a/arch/arm/boot/dts/imx6ul-geam.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
index 9f63706383a7..875ae699c5cb 100644
--- a/arch/arm/boot/dts/imx6ul-geam.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
@@ -148,7 +148,6 @@
 		reg = <0x0a>;
 		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6UL_CLK_OSC>;
-		clock-names = "mclk";
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
 		VDDD-supply = <&reg_1p8v>;
@@ -195,6 +194,7 @@
 };
 
 &pwm8 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-imx6ull-opos6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6ul.dtsi
index f2386dcb9ff2..f2386dcb9ff2 100644
--- a/arch/arm/boot/dts/imx6ul-imx6ull-opos6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6ul.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
index 18966350bfd8..18cac19aa9b0 100644
--- a/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
@@ -114,18 +114,6 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>, <&gpio4 3 GPIO_ACTIVE_LOW>;
 	status = "okay";
-
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <5000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <5000000>;
-	};
 };
 
 &i2c1 {
@@ -155,6 +143,7 @@
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-isiot-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-emmc.dts
index 1df3e376ae2c..1df3e376ae2c 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-emmc.dts
diff --git a/arch/arm/boot/dts/imx6ul-isiot-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dts
index 8c26d4d1a7bf..8c26d4d1a7bf 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dts
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
index cc9adce638f5..14fc4828ba4e 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
@@ -187,6 +187,7 @@
 };
 
 &pwm8 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
index 5bad29683cc3..0c643706a158 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
@@ -5,12 +5,12 @@
  * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
  */
 
-#include "imx6ul-kontron-n6310-s.dts"
+#include "imx6ul-kontron-bl.dts"
 
 / {
-	model = "Kontron N6310 S 43";
-	compatible = "kontron,imx6ul-n6310-s-43", "kontron,imx6ul-n6310-s",
-		     "kontron,imx6ul-n6310-som", "fsl,imx6ul";
+	model = "Kontron BL i.MX6UL 43 (N631X S 43)";
+	compatible = "kontron,bl-imx6ul-43", "kontron,bl-imx6ul",
+		     "kontron,sl-imx6ul", "fsl,imx6ul";
 
 	backlight {
 		compatible = "pwm-backlight";
@@ -41,6 +41,7 @@
 };
 
 &pwm7 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm7>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
index f05e91841202..33d5f27285a4 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
@@ -72,7 +72,6 @@
 &adc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc1>;
-	num-channels = <3>;
 	vref-supply = <&reg_vref_adc>;
 	status = "okay";
 };
@@ -84,7 +83,7 @@
 };
 
 &ecspi1 {
-	cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
@@ -153,6 +152,7 @@
 };
 
 &pwm8 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
@@ -177,7 +177,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
-	fsl,uart-has-rtscts;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -232,13 +232,6 @@
 	status = "okay";
 };
 
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-	status = "okay";
-};
-
 &iomuxc {
 	pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
 
@@ -279,7 +272,7 @@
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2grp{
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
 			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
@@ -409,10 +402,4 @@
 			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
 		>;
 	};
-
-	pinctrl_wdog: wdoggrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY	0x30b0
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl.dts
index 5a3e06d6219b..dadf6d3d5f52 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl.dts
@@ -7,11 +7,10 @@
 
 /dts-v1/;
 
-#include "imx6ul-kontron-n6310-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
+#include "imx6ul-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
 
 / {
-	model = "Kontron N6310 S";
-	compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som",
-		     "fsl,imx6ul";
+	model = "Kontron BL i.MX6UL (N631X S)";
+	compatible = "kontron,bl-imx6ul", "kontron,sl-imx6ul", "fsl,imx6ul";
 };
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl-common.dtsi
index a17af4d9bfdf..dcf88f610346 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl-common.dtsi
@@ -11,15 +11,20 @@
 	chosen {
 		stdout-path = &uart4;
 	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x10000000>;
+		device_type = "memory";
+	};
 };
 
 &ecspi2 {
-	cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
@@ -55,6 +60,23 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_qspi>;
 	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		spi-max-frequency = <104000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		reg = <0>;
+	};
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
 };
 
 &iomuxc {
@@ -106,4 +128,10 @@
 			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x1b0b0
 		>;
 	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY    0x18b0
+		>;
+	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl.dtsi
new file mode 100644
index 000000000000..0580d043e5ae
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+	model = "Kontron SL i.MX6UL (N631X SOM)";
+	compatible = "kontron,sl-imx6ul", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-liteboard.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-liteboard.dts
index 1d863a16bcf0..1d863a16bcf0 100644
--- a/arch/arm/boot/dts/imx6ul-liteboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-liteboard.dts
diff --git a/arch/arm/boot/dts/imx6ul-litesom.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-litesom.dtsi
index 8d6893210842..8d6893210842 100644
--- a/arch/arm/boot/dts/imx6ul-litesom.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-litesom.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-opos6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6ul.dtsi
index 6ce84f92b027..6ce84f92b027 100644
--- a/arch/arm/boot/dts/imx6ul-opos6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6ul.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-opos6uldev.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6uldev.dts
index 375b98d7205a..375b98d7205a 100644
--- a/arch/arm/boot/dts/imx6ul-opos6uldev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6uldev.dts
diff --git a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-phycore-som.dtsi
index 88f631c8fabb..a3ea1b208462 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-phycore-som.dtsi
@@ -30,7 +30,7 @@
 		pinctrl-0 = <&pinctrl_gpioleds_som>;
 		compatible = "gpio-leds";
 
-		phycore-green {
+		led-phycore-green {
 			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
@@ -68,13 +68,17 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <100000>;
 	status = "okay";
 
 	eeprom@52 {
 		compatible = "catalyst,24c32", "atmel,24c32";
+		pagesize = <32>;
 		reg = <0x52>;
 	};
 };
@@ -98,6 +102,10 @@
 	status = "disabled";
 };
 
+&wdog1 {
+	fsl,suspend-in-wait;
+};
+
 &iomuxc {
 	pinctrl_enet1: enet1grp {
 		fsl,pins = <
@@ -146,6 +154,13 @@
 		>;
 	};
 
+	pinctrl_i2c1_gpio: i2cgpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28	0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29	0x4001b8b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-emmc.dts
new file mode 100644
index 000000000000..cfc744f8fcad
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-emmc.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-phytec-phycore-som.dtsi"
+#include "imx6ul-phytec-segin.dtsi"
+#include "imx6ul-phytec-segin-peb-eval-01.dtsi"
+#include "imx6ul-phytec-segin-peb-av-02.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with eMMC";
+	compatible = "phytec,imx6ul-pbacd10-emmc", "phytec,imx6ul-pbacd10",
+		     "phytec,imx6ul-pcl063","fsl,imx6ul";
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&ecspi3 {
+	status = "okay";
+};
+
+&ethphy1 {
+	status = "okay";
+};
+
+&ethphy2 {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&fec2 {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&reg_can1_en {
+	status = "okay";
+};
+
+&reg_sound_1v8 {
+	status = "okay";
+};
+
+&reg_sound_3v3 {
+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&sound {
+	status = "okay";
+};
+
+&tlv320 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	status = "okay";
+};
+
+&usbotg2 {
+	status = "okay";
+};
+
+&usdhc1 {
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-nand.dts
index 699dfcbf9a60..607eddc5030f 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-nand.dts
@@ -9,6 +9,8 @@
 #include "imx6ul-phytec-phycore-som.dtsi"
 #include "imx6ul-phytec-segin.dtsi"
 #include "imx6ul-phytec-segin-peb-eval-01.dtsi"
+#include "imx6ul-phytec-segin-peb-av-02.dtsi"
+#include "imx6ul-phytec-segin-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with NAND";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-av-02.dtsi
new file mode 100644
index 000000000000..ec042648bd98
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-av-02.dtsi
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2016, 2020 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ * Author: Stefan Riedmueller <s.riedmueller@phytec.de>
+ */
+
+/ {
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <5>;
+		power-supply = <&reg_backlight_en>;
+		pwms = <&pwm3 0 5000000 0>;
+		status = "disabled";
+	};
+
+	lcd_panel: lcd-panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&backlight_lcd>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_parallel_out>;
+			};
+		};
+	};
+
+	reg_backlight_en: regulator-backlight-en {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_en>;
+		regulator-name = "backlight-lcd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&i2c1 {
+	edt_ft5406: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_edt_ft5406>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-source;
+		status = "disabled";
+	};
+
+	stmpe: touchscreen@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio5>;
+		wakeup-source;
+		status = "disabled";
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+			touchscreen-inverted-x;
+			touchscreen-inverted-y;
+		};
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat>;
+	status = "disabled";
+
+	port {
+		lcdif_parallel_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_edt_ft5406: edtft5406grp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0
+		>;
+	};
+
+	pinctrl_backlight_en: bachlightengrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x1b0b0
+		>;
+	};
+
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00  0x59
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01  0x59
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02  0x59
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03  0x59
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04  0x59
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05  0x59
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06  0x59
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07  0x59
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08  0x59
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09  0x59
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10  0x59
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11  0x59
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12  0x59
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13  0x59
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14  0x59
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15  0x59
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16  0x59
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17  0x59
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x59
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x59
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC    0x59
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC    0x59
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-eval-01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-eval-01.dtsi
index 2f3fd32a1167..2f3fd32a1167 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-eval-01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-eval-01.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-wlbt-05.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-wlbt-05.dtsi
new file mode 100644
index 000000000000..04477fd4b9a9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-wlbt-05.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	reg_wl_en: regulator-wl-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wl>;
+		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x3031	/* BT ENABLE */
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x3031	/* HOST WAKEUP */
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x3031	/* DEV WAKEUP */
+		>;
+	};
+
+	pinctrl_uart2_bt: uart2grp-bt {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX   0x17059
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX   0x17059
+			MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS    0x17059
+			MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS    0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_wl: usdhc2grp-wl {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__USDHC2_CMD    0x10051
+			MX6UL_PAD_LCD_DATA19__USDHC2_CLK    0x10061
+			MX6UL_PAD_LCD_DATA20__USDHC2_DATA0  0x10051
+			MX6UL_PAD_LCD_DATA21__USDHC2_DATA1  0x10051
+			MX6UL_PAD_LCD_DATA22__USDHC2_DATA2  0x10051
+			MX6UL_PAD_LCD_DATA23__USDHC2_DATA3  0x10051
+		>;
+	};
+
+	pinctrl_wl: wlgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09  0x3031	/* WLAN ENABLE */
+		>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_bt &pinctrl_bt>;
+	uart-has-rtscts;
+	status = "disabled";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usdhc2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_wl>;
+	vmmc-supply = <&reg_wl_en>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	status = "disabled";
+
+	brmcf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin.dtsi
index 8d5f8dc6ad58..38ea4dcfa228 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin.dtsi
@@ -83,11 +83,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc1>;
 	vref-supply = <&reg_adc1_vref_3v3>;
-	/*
-	 * driver can not separate a specific channel so we request 4 channels
-	 * here - we need only the fourth channel
-	 */
-	num-channels = <4>;
 	status = "disabled";
 };
 
@@ -106,7 +101,7 @@
 &ecspi3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
-	cs-gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
 	status = "disabled";
 };
 
@@ -130,31 +125,6 @@
 		status = "disabled";
 	};
 
-	stmpe: touchscreen@44 {
-		compatible = "st,stmpe811";
-		reg = <0x44>;
-		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-parent = <&gpio5>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_stmpe>;
-		status = "disabled";
-
-		touchscreen {
-			compatible = "st,stmpe-ts";
-			st,sample-time = <4>;
-			st,mod-12b = <1>;
-			st,ref-sel = <0>;
-			st,adc-freq = <1>;
-			st,ave-ctrl = <1>;
-			st,touch-det-delay = <2>;
-			st,settling = <2>;
-			st,fraction-z = <7>;
-			st,i-drive = <1>;
-			touchscreen-inverted-x = <1>;
-			touchscreen-inverted-y = <1>;
-		};
-	};
-
 	i2c_rtc: rtc@68 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc_int>;
@@ -176,12 +146,6 @@
 	};
 };
 
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "disabled";
-};
-
 &sai2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai2>;
@@ -222,6 +186,7 @@
 	no-1-8-v;
 	keep-power-in-suspend;
 	wakeup-source;
+	disable-wp;
 	status = "disabled";
 };
 
@@ -267,12 +232,6 @@
 		>;
 	};
 
-	pinctrl_pwm3: pwm3grp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
-		>;
-	};
-
 	pinctrl_rtc_int: rtcintgrp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
@@ -289,12 +248,6 @@
 		>;
 	};
 
-	pinctrl_stmpe: stmpegrp {
-		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
-		>;
-	};
-
 	pinctrl_uart5: uart5grp {
 		fsl,pins = <
 			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dts
new file mode 100644
index 000000000000..fb206c1d8aca
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright 2015 Technexion Ltd.
+//
+// Author: Wig Cheng  <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+/dts-v1/;
+
+#include "imx6ul-pico.dtsi"
+/ {
+	model = "TechNexion PICO-IMX6UL and DWARF baseboard";
+	compatible = "technexion,imx6ul-pico-dwarf", "fsl,imx6ul";
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx6ul-sgtl5000";
+		audio-cpu = <&sai1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"LINE_IN", "Line In Jack",
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+	};
+
+	sys_mclk: clock-sys-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	sgtl5000: audio-codec@a {
+		reg = <0x0a>;
+		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
+		clocks = <&sys_mclk>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	pressure-sensor@60 {
+		compatible = "fsl,mpl3115";
+		reg = <0x60>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-hobbit.dts
index 09f7ffa9ad8c..bf7dbb4f1f3e 100644
--- a/arch/arm/boot/dts/imx6ul-pico-hobbit.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-hobbit.dts
@@ -51,6 +51,7 @@
 	sgtl5000: codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6ul-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-pi.dts
index 6cd7d5877d20..6cfc943a8fa3 100644
--- a/arch/arm/boot/dts/imx6ul-pico-pi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-pi.dts
@@ -51,6 +51,7 @@
 	sgtl5000: codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6ul-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
index de9f83189ba8..07dcecbe485d 100644
--- a/arch/arm/boot/dts/imx6ul-pico.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
@@ -20,7 +20,7 @@
 		stdout-path = &uart6;
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm3 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -72,6 +72,17 @@
 		regulator-max-microvolt = <3300000>;
 		startup-delay-us = <200000>;
 	};
+
+	panel {
+		compatible = "vxt,vl050-8048nt-c01";
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
 };
 
 &can1 {
@@ -110,6 +121,8 @@
 			max-speed = <100>;
 			interrupt-parent = <&gpio5>;
 			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
 		};
 	};
 };
@@ -120,7 +133,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -154,36 +167,17 @@
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>;
-	display = <&display0>;
 	status = "okay";
 
-	display0: display0 {
-		bits-per-pixel = <32>;
-		bus-width = <24>;
-
-		display-timings {
-			native-mode = <&timing0>;
-
-			timing0: timing0 {
-				clock-frequency = <33200000>;
-				hactive = <800>;
-				vactive = <480>;
-				hfront-porch = <210>;
-				hback-porch = <46>;
-				hsync-len = <1>;
-				vback-porch = <22>;
-				vfront-porch = <23>;
-				vsync-len = <1>;
-				hsync-active = <0>;
-				vsync-active = <0>;
-				de-active = <1>;
-				pixelclk-active = <0>;
-			};
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
 		};
 	};
 };
 
 &pwm3 {
+	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6ul-pinfunc.h
index 380d2db13a9b..380d2db13a9b 100644
--- a/arch/arm/boot/dts/imx6ul-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pinfunc.h
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-prti6g.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-prti6g.dts
new file mode 100644
index 000000000000..c3c50f51a5a8
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-prti6g.dts
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Protonic PRTI6G Board";
+	compatible = "prt,prti6g", "fsl,imx6ul";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	clock_ksz8081_in: clock-ksz8081-in {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_ksz8081_out: clock-ksz8081-out {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet1_ref_pad";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_3v2: regulator-3v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v2";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>, <&clock_ksz8081_out>;
+	clock-names = "ckil", "osc", "ipp_di0", "ipp_di1", "enet1_ref_pad";
+	assigned-clocks = <&clks IMX6UL_CLK_ENET1_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081_out>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eth1>;
+	phy-mode = "rmii";
+	phy-handle = <&rmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+			clocks = <&clock_ksz8081_in>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3v2>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX		0x0b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX		0x0b0b0
+			/* SR */
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03		0x0b0b0
+			/* TERM */
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04		0x0b0b0
+			/* nSMBALERT */
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02		0x0b0b0
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX		0x0b0b0
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX		0x0b0b0
+			/* SR */
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05		0x0b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK		0x0b0b0
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26		0x000b1
+			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI		0x0b0b0
+			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO		0x0b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK		0x0b0b0
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22		0x000b1
+			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI		0x0b0b0
+			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO		0x0b0b0
+		>;
+	};
+
+	pinctrl_eth1: eth1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC			0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO		0x100b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00		0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01		0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN		0x100b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER		0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN		0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00		0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01		0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1		0x1b000
+			/* PHY ENET1_RST */
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00		0x00880
+			/* PHY ENET1_IRQ */
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01		0x00880
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* HW revision detect */
+			/* REV_ID0 */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08		0x1b0b0
+			/* REV_ID1 */
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09		0x1b0b0
+			/* REV_ID2 */
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10		0x1b0b0
+			/* REV_ID3 */
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11		0x1b0b0
+			/* BOARD_ID0 */
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13		0x1b0b0
+			/* BOARD_ID1 */
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14		0x1b0b0
+			/* BOARD_ID2 */
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15		0x1b0b0
+			/* BOARD_ID3 */
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12		0x1b0b0
+			/* Safety controller IO */
+			/* WAKE_SC */
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06		0x1b0b0
+			/* PROGRAM_SC */
+			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__I2C2_SDA		0x4001b8b0
+			MX6UL_PAD_CSI_HSYNC__I2C2_SCL		0x4001b8b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16			0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX		0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x070b1
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x07099
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x070b1
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x070b1
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x070b1
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x070b1
+			/* SD1 CD */
+			MX6UL_PAD_NAND_READY_B__GPIO4_IO12		0x170b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD			0x170f9
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK			0x100f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0		0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1		0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2		0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3		0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4		0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5		0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6		0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7		0x170f9
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B		0x170b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul-common.dtsi
new file mode 100644
index 000000000000..57e647fc3237
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul-common.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULxL
+ * - TQMa6ULLx
+ * - TQMa6ULLxL
+ */
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_recovery>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3000: pmic@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			reg_sw1a: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <6250>;
+				/* not used */
+			};
+
+			reg_sw1b_core: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			reg_sw2: sw2 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_sw3_ddr: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_swbst: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				/* not used */
+			};
+
+			reg_snvs_3v0: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vrefddr: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vccsd: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_v33_3v3: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vldo1_3v3: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				/* not used */
+			};
+
+			reg_vldo2: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				/* not used */
+			};
+
+			reg_vldo3: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				/* not used */
+			};
+
+			reg_vldo4: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	jc42_1a: eeprom-temperature@1a {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x1a>;
+	};
+
+	m24c64_50: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	m24c02_52: eeprom@52 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+		read-only;
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	/*
+	 * PMIC & temperature sensor IRQ
+	 * Both do currently not use IRQ
+	 * potentially dangerous if used on baseboard
+	 */
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <24 0>;
+		input;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <33000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+		reg = <0>;
+	};
+};
+
+/* eMMC */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz" , "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+
+	bus-width = <8>;
+	disable-wp;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001b8b0
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c4_recovery: i2c4recoverygrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x4001b8b0
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x4001b8b0
+		>;
+	};
+
+	pinctrl_pmic: pmic {
+		fsl,pins = <
+			/* PMIC irq */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x1b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1-mba6ulx.dts
new file mode 100644
index 000000000000..f2a5f17f312e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1-mba6ulx.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul1.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL1 SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul1-mba6ulx", "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * Note: can2 and fec2 are enabled on mba6ulx level (for i.MX6ULG2 usage)
+ * and need to be disabled here again
+ */
+&can2 {
+	status = "disabled";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_mdc>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			reg = <0>;
+		};
+	};
+};
+
+&fec2 {
+	/delete-property/ phy-handle;
+	/delete-node/ mdio;
+};
+
+&iomuxc {
+	pinctrl_enet1_mdc: enet1mdcgrp {
+		fsl,pins = <
+			/* mdio */
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1.dtsi
new file mode 100644
index 000000000000..24192d012ef7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul-tqma6ul2.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL1 SoM";
+	compatible = "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * There are no module specific differences compared to TQMa6UL2,
+ * only external interfaces differ
+ */
+
+/*
+ * Devices not available on i.MX6ULG1 and should not be enabled on
+ * mainboard level (again)
+ */
+&can2 {
+	status = "disabled";
+};
+
+&csi {
+	status = "disabled";
+};
+
+&fec2 {
+	status = "disabled";
+};
+
+&lcdif {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2-mba6ulx.dts
new file mode 100644
index 000000000000..0757df2b8f48
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULx SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul2-mba6ulx", "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2.dtsi
new file mode 100644
index 000000000000..e2e95dd92263
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL2 SoM";
+	compatible = "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017051
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017051
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017051
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017051
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017051
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017051
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017051
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017051
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017051
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017051
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170e1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170e1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170e1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170e1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170e1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170e1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170e1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170e1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170e1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170e1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dts
new file mode 100644
index 000000000000..9d9b6b744a1c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6UL2L SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul2l-mba6ulx", "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l.dtsi
new file mode 100644
index 000000000000..4b87e2dc70dc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL2L SoM";
+	compatible = "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017051
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017051
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017051
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017051
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017051
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017051
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017051
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017051
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017051
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017051
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170e1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulx-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulx-common.dtsi
new file mode 100644
index 000000000000..5afb9046c202
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulx-common.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULLx
+ */
+
+&m24c64_50 {
+	vcc-supply = <&reg_sw2>;
+};
+
+&m24c02_52 {
+	vcc-supply = <&reg_sw2>;
+};
+
+&reg_sw2 {
+	regulator-boot-on;
+	regulator-always-on;
+};
+
+/* eMMC */
+&usdhc2 {
+	vmmc-supply = <&reg_sw2>;
+	vqmmc-supply = <&reg_vldo4>;
+};
+
+&iomuxc {
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70b9
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70b9
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70b9
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70b9
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70b9
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulxl-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulxl-common.dtsi
new file mode 100644
index 000000000000..ba84a4f70ebd
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulxl-common.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULxL
+ * - TQMa6ULLxL
+ */
+
+/ {
+	reg_vin: reg-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "VIN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&m24c64_50 {
+	vcc-supply = <&reg_vin>;
+};
+
+&m24c02_52 {
+	vcc-supply = <&reg_vin>;
+};
+
+/* eMMC */
+&usdhc2 {
+	vmmc-supply = <&reg_vin>;
+	vqmmc-supply = <&reg_vldo4>;
+};
+
+&iomuxc {
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70a9
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a9
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70a9
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70a9
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70a9
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dts
index 8c2f3df79b47..8c2f3df79b47 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dts
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0011.dts
index d82698e7d50f..d82698e7d50f 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0011.dts
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-mainboard.dts
index 97686097a86e..ef76ece21010 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-mainboard.dts
@@ -119,7 +119,7 @@
 	/delete-node/ codec@a;
 	/delete-node/ touchscreen@48;
 
-	rtc: mcp7940x@6f {
+	rtc: rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
 	};
@@ -133,7 +133,7 @@
 	pinctrl-0 = <&pinctrl_disp0_3>;
 };
 
-&reg_usbotg_vbus{
+&reg_usbotg_vbus {
 	status = "disabled";
 };
 
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
index bb6dbfd5546b..1db146ac1c17 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
@@ -114,10 +114,8 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c_gpio>;
-		gpios = <
-			&gpio5 1 GPIO_ACTIVE_HIGH /* SDA */
-			&gpio5 0 GPIO_ACTIVE_HIGH /* SCL */
-		>;
+		sda-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
 		clock-frequency = <400000>;
 		status = "okay";
 
@@ -131,7 +129,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user_led: user {
+		user_led: led-user {
 			label = "Heartbeat";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_led>;
@@ -212,33 +210,21 @@
 		enable-active-high;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi_gpio>;
-		gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>;
-		gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <2>;
 		cs-gpios = <
 			&gpio1 29 GPIO_ACTIVE_HIGH
 			&gpio1 10 GPIO_ACTIVE_HIGH
 		>;
 		status = "disabled";
-
-		spi@0 {
-			compatible = "spidev";
-			reg = <0>;
-			spi-max-frequency = <660000>;
-		};
-
-		spi@1 {
-			compatible = "spidev";
-			reg = <1>;
-			spi-max-frequency = <660000>;
-		};
 	};
 
 	sound {
@@ -290,18 +276,6 @@
 		&gpio1 10 GPIO_ACTIVE_HIGH
 	>;
 	status = "disabled";
-
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <60000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <60000000>;
-	};
 };
 
 &fec1 {
@@ -549,7 +523,6 @@
 &pwm5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm5>;
-	#pwm-cells = <3>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index d9fdca12819b..a27a7554c2e7 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -47,6 +47,8 @@
 		spi1 = &ecspi2;
 		spi2 = &ecspi3;
 		spi3 = &ecspi4;
+		usb0 = &usbotg1;
+		usb1 = &usbotg2;
 		usbphy0 = &usbphy1;
 		usbphy1 = &usbphy2;
 	};
@@ -62,20 +64,18 @@
 			clock-frequency = <696000000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
-			operating-points = <
+			operating-points =
 				/* kHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1025000
-				198000	950000
-			>;
-			fsl,soc-operating-points = <
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1025000>,
+				<198000	950000>;
+			fsl,soc-operating-points =
 				/* KHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1175000
-				198000	1175000
-			>;
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1175000>,
+				<198000	1175000>;
 			clocks = <&clks IMX6UL_CLK_ARM>,
 				 <&clks IMX6UL_CLK_PLL2_BUS>,
 				 <&clks IMX6UL_CLK_PLL2_PFD2>,
@@ -131,23 +131,13 @@
 		clock-output-names = "ipp_di1";
 	};
 
-	tempmon: tempmon {
-		compatible = "fsl,imx6ul-tempmon", "fsl,imx6sx-tempmon";
-		interrupt-parent = <&gpc>;
-		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-		fsl,tempmon = <&anatop>;
-		nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
-		nvmem-cell-names = "calib", "temp_grade";
-		clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
-	};
-
 	pmu {
 		compatible = "arm,cortex-a7-pmu";
 		interrupt-parent = <&gpc>;
 		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -157,6 +147,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -171,23 +164,22 @@
 			      <0x00a06000 0x2000>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX6UL_CLK_APBHDMA>;
 		};
 
-		gpmi: gpmi-nand@1806000 {
+		gpmi: nand-controller@1806000 {
 			compatible = "fsl,imx6q-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x01806000 0x2000>, <0x01808000 0x2000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -204,7 +196,7 @@
 			status = "disabled";
 		};
 
-		aips1: aips-bus@2000000 {
+		aips1: bus@2000000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -351,6 +343,31 @@
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};
+
+				asrc: asrc@2034000 {
+					compatible = "fsl,imx6ul-asrc", "fsl,imx53-asrc";
+					reg = <0x2034000 0x4000>;
+					interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_ASRC_IPG>,
+						<&clks IMX6UL_CLK_ASRC_MEM>, <&clks 0>,
+						<&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+						<&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+						<&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+						<&clks IMX6UL_CLK_SPDIF>, <&clks 0>, <&clks 0>,
+						<&clks IMX6UL_CLK_SPBA>;
+					clock-names = "mem", "ipg", "asrck_0",
+						"asrck_1", "asrck_2", "asrck_3", "asrck_4",
+						"asrck_5", "asrck_6", "asrck_7", "asrck_8",
+						"asrck_9", "asrck_a", "asrck_b", "asrck_c",
+						"asrck_d", "asrck_e", "asrck_f", "spba";
+					dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>,
+						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
+					dma-names = "rxa", "rxb", "rxc",
+						    "txa", "txb", "txc";
+					fsl,asrc-rate = <48000>;
+					fsl,asrc-width = <16>;
+					status = "okay";
+				};
 			};
 
 			tsc: tsc@2040000 {
@@ -371,7 +388,7 @@
 				clocks = <&clks IMX6UL_CLK_PWM1>,
 					 <&clks IMX6UL_CLK_PWM1>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -382,7 +399,7 @@
 				clocks = <&clks IMX6UL_CLK_PWM2>,
 					 <&clks IMX6UL_CLK_PWM2>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -393,7 +410,7 @@
 				clocks = <&clks IMX6UL_CLK_PWM3>,
 					 <&clks IMX6UL_CLK_PWM3>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -404,33 +421,33 @@
 				clocks = <&clks IMX6UL_CLK_PWM4>,
 					 <&clks IMX6UL_CLK_PWM4>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
-			can1: flexcan@2090000 {
+			can1: can@2090000 {
 				compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
 				reg = <0x02090000 0x4000>;
 				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_CAN1_IPG>,
 					 <&clks IMX6UL_CLK_CAN1_SERIAL>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x10 1 0x10 17>;
+				fsl,stop-mode = <&gpr 0x10 1>;
 				status = "disabled";
 			};
 
-			can2: flexcan@2094000 {
+			can2: can@2094000 {
 				compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
 				reg = <0x02094000 0x4000>;
 				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_CAN2_IPG>,
 					 <&clks IMX6UL_CLK_CAN2_SERIAL>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x10 2 0x10 18>;
+				fsl,stop-mode = <&gpr 0x10 2>;
 				status = "disabled";
 			};
 
-			gpt1: gpt@2098000 {
+			gpt1: timer@2098000 {
 				compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -514,31 +531,32 @@
 				clocks = <&clks IMX6UL_CLK_ENET>,
 					 <&clks IMX6UL_CLK_ENET_AHB>,
 					 <&clks IMX6UL_CLK_ENET_PTP>,
-					 <&clks IMX6UL_CLK_ENET2_REF_125M>,
-					 <&clks IMX6UL_CLK_ENET2_REF_125M>;
+					 <&clks IMX6UL_CLK_ENET2_REF_SEL>;
 				clock-names = "ipg", "ahb", "ptp",
-					      "enet_clk_ref", "enet_out";
+					      "enet_clk_ref";
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
+				fsl,stop-mode = <&gpr 0x10 4>;
+				fsl,magic-packet;
 				status = "disabled";
 			};
 
-			kpp: kpp@20b8000 {
-				compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
+			kpp: keypad@20b8000 {
+				compatible = "fsl,imx6ul-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_KPP>;
 				status = "disabled";
 			};
 
-			wdog1: wdog@20bc000 {
+			wdog1: watchdog@20bc000 {
 				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
 				reg = <0x020bc000 0x4000>;
 				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_WDOG1>;
 			};
 
-			wdog2: wdog@20c0000 {
+			wdog2: watchdog@20c0000 {
 				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
 				reg = <0x020c0000 0x4000>;
 				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
@@ -546,7 +564,7 @@
 				status = "disabled";
 			};
 
-			clks: ccm@20c4000 {
+			clks: clock-controller@20c4000 {
 				compatible = "fsl,imx6ul-ccm";
 				reg = <0x020c4000 0x4000>;
 				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
@@ -611,6 +629,16 @@
 					anatop-min-voltage = <725000>;
 					anatop-max-voltage = <1450000>;
 				};
+
+				tempmon: tempmon {
+					compatible = "fsl,imx6ul-tempmon", "fsl,imx6sx-tempmon";
+					interrupt-parent = <&gpc>;
+					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+					fsl,tempmon = <&anatop>;
+					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+					nvmem-cell-names = "calib", "temp_grade";
+					clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
+				};
 			};
 
 			usbphy1: usbphy@20c9000 {
@@ -676,7 +704,7 @@
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6ul-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -691,9 +719,21 @@
 				#interrupt-cells = <3>;
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&intc>;
+				clocks = <&clks IMX6UL_CLK_IPG>;
+				clock-names = "ipg";
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					power-domain@0 {
+						reg = <0>;
+						#power-domain-cells = <0>;
+					};
+				};
 			};
 
-			iomuxc: iomuxc@20e0000 {
+			iomuxc: pinctrl@20e0000 {
 				compatible = "fsl,imx6ul-iomuxc";
 				reg = <0x020e0000 0x4000>;
 			};
@@ -704,7 +744,7 @@
 				reg = <0x020e4000 0x4000>;
 			};
 
-			gpt2: gpt@20e8000 {
+			gpt2: timer@20e8000 {
 				compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
 				reg = <0x020e8000 0x4000>;
 				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
@@ -714,7 +754,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
 					     "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
@@ -733,7 +773,7 @@
 				clocks = <&clks IMX6UL_CLK_PWM5>,
 					 <&clks IMX6UL_CLK_PWM5>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -744,7 +784,7 @@
 				clocks = <&clks IMX6UL_CLK_PWM6>,
 					 <&clks IMX6UL_CLK_PWM6>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -755,7 +795,7 @@
 				clocks = <&clks IMX6UL_CLK_PWM7>,
 					 <&clks IMX6UL_CLK_PWM7>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -766,19 +806,19 @@
 				clocks = <&clks IMX6UL_CLK_PWM8>,
 					 <&clks IMX6UL_CLK_PWM8>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 		};
 
-		aips2: aips-bus@2100000 {
+		aips2: bus@2100000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x02100000 0x100000>;
 			ranges;
 
-			crypto: caam@2140000 {
+			crypto: crypto@2140000 {
 				compatible = "fsl,imx6ul-caam", "fsl,sec-v4.0";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -789,19 +829,19 @@
 					 <&clks IMX6UL_CLK_CAAM_MEM>;
 				clock-names = "ipg", "aclk", "mem";
 
-				sec_jr0: jr0@1000 {
+				sec_jr0: jr@1000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr1: jr1@2000 {
+				sec_jr1: jr@2000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x2000 0x1000>;
 					interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr2: jr2@3000 {
+				sec_jr2: jr@3000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x3000 0x1000>;
 					interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
@@ -850,16 +890,17 @@
 				clocks = <&clks IMX6UL_CLK_ENET>,
 					 <&clks IMX6UL_CLK_ENET_AHB>,
 					 <&clks IMX6UL_CLK_ENET_PTP>,
-					 <&clks IMX6UL_CLK_ENET_REF>,
-					 <&clks IMX6UL_CLK_ENET_REF>;
+					 <&clks IMX6UL_CLK_ENET1_REF_SEL>;
 				clock-names = "ipg", "ahb", "ptp",
-					      "enet_clk_ref", "enet_out";
+					      "enet_clk_ref";
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
+				fsl,stop-mode = <&gpr 0x10 3>;
+				fsl,magic-packet;
 				status = "disabled";
 			};
 
-			usdhc1: usdhc@2190000 {
+			usdhc1: mmc@2190000 {
 				compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -873,7 +914,7 @@
 				status = "disabled";
 			};
 
-			usdhc2: usdhc@2194000 {
+			usdhc2: mmc@2194000 {
 				compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -892,7 +933,6 @@
 				reg = <0x02198000 0x4000>;
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_ADC1>;
-				num-channels = <2>;
 				clock-names = "adc";
 				fsl,adck-max-frequency = <30000000>, <40000000>,
 							 <20000000>;
@@ -946,7 +986,7 @@
 				status = "disabled";
 			};
 
-			ocotp: ocotp-ctrl@21bc000 {
+			ocotp: efuse@21bc000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6ul-ocotp", "syscon";
@@ -967,7 +1007,7 @@
 			};
 
 			csi: csi@21c4000 {
-				compatible = "fsl,imx6ul-csi", "fsl,imx7-csi";
+				compatible = "fsl,imx6ul-csi";
 				reg = <0x021c4000 0x4000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_CSI>;
@@ -976,7 +1016,7 @@
 			};
 
 			lcdif: lcdif@21c8000 {
-				compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx6ul-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x021c8000 0x4000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_LCDIF_PIX>,
@@ -997,7 +1037,7 @@
 			qspi: spi@21e0000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
+				compatible = "fsl,imx6ul-qspi";
 				reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
 				reg-names = "QuadSPI", "QuadSPI-memory";
 				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
@@ -1007,7 +1047,7 @@
 				status = "disabled";
 			};
 
-			wdog3: wdog@21e4000 {
+			wdog3: watchdog@21e4000 {
 				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
 				reg = <0x021e4000 0x4000>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/imx6ull-14x14-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-14x14-evk.dts
index 74aaa8a56a3d..74aaa8a56a3d 100644
--- a/arch/arm/boot/dts/imx6ull-14x14-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-14x14-evk.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dts
new file mode 100644
index 000000000000..3e0897c3a296
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-aster",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
+
+/* PWM <C> */
+&pwm6 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtsi
new file mode 100644
index 000000000000..de4dc7c1a03a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtsi
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		power {
+			label = "Wake-Up";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&ecspi1 {
+	status = "okay";
+
+	num-cs = <2>;
+	cs-gpios = <
+		&gpio3 26 GPIO_ACTIVE_HIGH /* SODIMM 86 LCD_DATA21 */
+		&gpio4 28 GPIO_ACTIVE_HIGH /* SODIMM 65 CSI_DATA07 */
+	>;
+};
+
+/*
+ * Following SODIMM Pins should not be accessed as GPIO on Aster board:
+ * 134 - AIN5_SCL (no connection)
+ * 127 - Voltage Level Translator OE# signal (IC11 and IC12)
+ *
+ * To configure GPIO to LED5, please disable FEC2 and uncomment the following:
+ *	&iomuxc {
+ *		pinctrl-names = "default";
+ *		pinctrl-0 = <
+ *			&pinctrl_gpio1
+ *			&pinctrl_gpio2
+ *			&pinctrl_gpio3
+ *			&pinctrl_gpio4
+ *			&pinctrl_gpio6 - for non-WiFi modules only
+ *			&pinctrl_gpio7
+ *			&pinctrl_gpio_aster
+ *		>;
+ *
+ *		pinctrl_gpio_aster: gpio-aster {
+ *			fsl,pins = <
+ *				MX6UL_PAD_GPIO1_IO07__GPIO1_IO07    0x1b0b0
+ *			>;
+ *		};
+ *  };
+ */
+
+&i2c1 {
+	status = "okay";
+
+	m41t0m6: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	status = "okay";
+};
+
+/* PWM <C> */
+&pwm6 {
+	status = "okay";
+};
+
+/* PWM <D> */
+&pwm7 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-aster.dts
new file mode 100644
index 000000000000..b2cdf4877718
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-aster.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-emmc-aster",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-eval-v3.dts
new file mode 100644
index 000000000000..2dc16c54fc78
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-eval-v3.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2021 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx6ull-emmc-eval",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..9bae08fb7f85
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris-v2.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1G (eMMC) on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-emmc-iris-v2",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..0b1603ff9420
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-emmc-iris",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-nonwifi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-nonwifi.dtsi
new file mode 100644
index 000000000000..ea238525d5c0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-nonwifi.dtsi
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx6ull-colibri.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &usdhc2; /* eMMC */
+		mmc1 = &usdhc1; /* MMC 4-bit slot */
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "SODIMM_89",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_140",
+			  "SODIMM_59",
+			  "SODIMM_142",
+			  "SODIMM_144",
+			  "SODIMM_133",
+			  "SODIMM_146",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "SODIMM_81",
+			  "SODIMM_94",
+			  "SODIMM_101",
+			  "SODIMM_103",
+			  "SODIMM_79",
+			  "SODIMM_97",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "SODIMM_93",
+			  "",
+			  "SODIMM_138",
+			  "",
+			  "SODIMM_105",
+			  "SODIMM_127";
+};
+
+/* NAND */
+&gpmi {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
+		&pinctrl_gpio4 &pinctrl_gpio6 &pinctrl_gpio7
+		&pinctrl_gpmi_gpio>;
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
+};
+
+/* eMMC */
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2emmc>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+	bus-width = <8>;
+	keep-power-in-suspend;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_module_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dts
new file mode 100644
index 000000000000..c5bc255b21e1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx6ull-eval", "toradex,colibri-imx6ull", "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dtsi
index a78849fd2afa..692ef26fbab3 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 / {
@@ -8,20 +8,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
 	/* fixed crystal dedicated to mcp2515 */
 	clk16m: clk16m {
 		compatible = "fixed-clock";
@@ -29,18 +15,6 @@
 		clock-frequency = <16000000>;
 	};
 
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
 	reg_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
@@ -71,14 +45,6 @@
 	status = "okay";
 };
 
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-	pwms = <&pwm4 0 5000000 1>;
-	status = "okay";
-};
-
 &ecspi1 {
 	status = "okay";
 
@@ -107,16 +73,6 @@
 	};
 };
 
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
 /* PWM <A> */
 &pwm4 {
 	status = "okay";
@@ -150,29 +106,18 @@
 };
 
 &usbotg1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
+	disable-over-current;
 	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
 
 &usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
-	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	wakeup-source;
-	keep-power-in-suspend;
 	vmmc-supply = <&reg_3v3>;
-	vqmmc-supply = <&reg_sd1_vmmc>;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dts
new file mode 100644
index 000000000000..f6b31118be17
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dts
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256M/512B on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-iris-v2",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio1 {
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+};
+
+&gpio5 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
+
+/* PWM <C> */
+&pwm6 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..93649cad0cc0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dtsi
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+	};
+};
+
+
+&usdhc1 {
+	cap-power-off-card;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dts
new file mode 100644
index 000000000000..2a0d0fc3b9d6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-iris",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dtsi
new file mode 100644
index 000000000000..f52f8b5ad8a6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		power {
+			label = "Wake-Up";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&gpio1 {
+	/*
+	 * uart25_tx_on turns the UART transceiver on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled
+	 * in userspace.
+	 * The same applies to uart1_tx_on.
+	 */
+	uart25_tx_on-hog {
+		gpio-hog;
+		gpios = <15 0>;
+		output-high;
+	};
+};
+
+&gpio2 {
+	uart1_tx_on-hog {
+		gpio-hog;
+		gpios = <7 0>;
+		output-high;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	m41t0m6: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	status = "okay";
+};
+
+/* PWM <C> */
+&pwm6 {
+	status = "okay";
+};
+
+/* PWM <D> */
+&pwm7 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-nonwifi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-nonwifi.dtsi
new file mode 100644
index 000000000000..88901db255d6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-nonwifi.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "SODIMM_89",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_59",
+			  "",
+			  "",
+			  "SODIMM_133",
+			  "",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "SODIMM_81",
+			  "SODIMM_94",
+			  "SODIMM_101",
+			  "SODIMM_103",
+			  "SODIMM_79",
+			  "SODIMM_97",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "SODIMM_93",
+			  "",
+			  "SODIMM_138",
+			  "",
+			  "SODIMM_105",
+			  "SODIMM_127";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
+		&pinctrl_gpio4 &pinctrl_gpio6 &pinctrl_gpio7>;
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-aster.dts
new file mode 100644
index 000000000000..d3bbd05da293
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-aster.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-wifi-aster",
+		     "toradex,colibri-imx6ull-wifi",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
+
+/* PWM <C> */
+&pwm6 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-eval-v3.dts
new file mode 100644
index 000000000000..0ac306c9cef2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-eval-v3.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx6ull-wifi-eval", "toradex,colibri-imx6ull-wifi", "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris-v2.dts
new file mode 100644
index 000000000000..38cd52c45496
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris-v2.dts
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-wifi-iris-v2",
+		     "toradex,colibri-imx6ull-wifi",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio1 {
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+};
+
+&gpio5 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris.dts
new file mode 100644
index 000000000000..5f60df64f173
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-wifi-iris",
+		     "toradex,colibri-imx6ull-wifi",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi.dtsi
new file mode 100644
index 000000000000..db59ee6b1c86
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi.dtsi
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	wifi_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_wifi_pdn>;
+		reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_59",
+			  "",
+			  "",
+			  "SODIMM_133",
+			  "",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_105";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
+		&pinctrl_gpio4 &pinctrl_gpio7>;
+
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_gpio1>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	max-frequency = <25000000>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_module_3v3>;
+	wakeup-source;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri.dtsi
new file mode 100644
index 000000000000..ec3c1e7301f4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri.dtsi
@@ -0,0 +1,772 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull.dtsi"
+
+/ {
+	/* Ethernet aliases to ensure correct MAC addresses */
+	aliases {
+		ethernet0 = &fec2;
+		ethernet1 = &fec1;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_bl_on>;
+		power-supply = <&reg_3v3>;
+		pwms = <&pwm4 0 5000000 1>;
+		status = "disabled";
+	};
+
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_usbc_det>;
+		id-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		label = "USBC";
+		self-powered;
+		type = "micro";
+
+		port {
+			usb_dr_connector: endpoint {
+				remote-endpoint = <&usb1_drd_sw>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio5 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_module_3v3_avdd: regulator-module-3v3-avdd {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-name = "+V3.3_AVDD_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_sd1_vqmmc: regulator-sd1-vqmmc {
+		compatible = "regulator-gpio";
+		gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_reg_sd>;
+		regulator-always-on;
+		regulator-name = "+V3.3_1.8_SD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <1800000 0x1 3300000 0x0>;
+		vin-supply = <&reg_module_3v3>;
+	};
+
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed-clock";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		vin-supply = <&reg_module_3v3>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+		startup-delay-us = <150000>;
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_module_3v3_avdd>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "disabled";
+};
+
+/* Colibri SPI */
+&ecspi1 {
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
+};
+
+/* Ethernet */
+&fec2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet2>;
+	pinctrl-1 = <&pinctrl_enet2_sleep>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_eth_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@2 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			reg = <2>;
+		};
+	};
+};
+
+/* NAND */
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	fsl,use-minimum-ecc;
+	nand-on-flash-bbt;
+	nand-ecc-mode = "hw";
+	nand-ecc-strength = <8>;
+	nand-ecc-step-size = <512>;
+	status = "okay";
+};
+
+/* I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board) */
+&i2c1 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn &pinctrl_atmel_snvs_conn>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;       /* SODIMM 107 / INT */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;    /* SODIMM 106 / RST */
+		status = "disabled";
+	};
+};
+
+/*
+ * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
+ * touch screen controller
+ */
+&i2c2 {
+	/* Use low frequency to compensate for the high pull-up values. */
+	clock-frequency = <40000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	ad7879_ts: touchscreen@2c {
+		compatible = "adi,ad7879-1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_ad7879_int>;
+		reg = <0x2c>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-max-pressure = <4096>;
+		adi,resistance-plate-x = <120>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+		status = "disabled";
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	status = "disabled";
+
+	port {
+		lcdif_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+};
+
+/* PWM <B> */
+&pwm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm5>;
+};
+
+/* PWM <C> */
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+};
+
+/* PWM <D> */
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+};
+
+&sdma {
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "disabled";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
+	uart-has-rtscts;
+	fsl,dte-mode;
+};
+
+/* Colibri UART_B */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	fsl,dte-mode;
+};
+
+/* Colibri UART_C */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	fsl,dte-mode;
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	usb-role-switch;
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	dr_mode = "host";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd_sleep>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* MMC_CD */
+	disable-wp;
+	keep-power-in-suspend;
+	no-1-8-v;
+	vqmmc-supply = <&reg_sd1_vqmmc>;
+	wakeup-source;
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00        0x3000 /* SODIMM 8 */
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01        0x3000 /* SODIMM 6 */
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08        0x3000 /* SODIMM 4 */
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09        0x3000 /* SODIMM 2 */
+		>;
+	};
+
+	pinctrl_atmel_adap: atmeladapgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16          0xb0a0  /* SODIMM 28 */
+			MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05       0xb0a0  /* SODIMM 30 */
+		>;
+	};
+
+	pinctrl_atmel_conn: atmelconngrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10          0xb0a0  /* SODIMM 106 */
+		>;
+	};
+
+	pinctrl_can_int: canintgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0x13010	/* SODIMM 73 */
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet2_sleep: enet2-sleepgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__GPIO1_IO06	0x0
+			MX6UL_PAD_GPIO1_IO07__GPIO1_IO07	0x0
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x0
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x0
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x0
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11	0x0
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12	0x0
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x0
+		>;
+	};
+
+	pinctrl_ecspi1_cs: ecspi1csgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x70a0	/* SODIMM 86 */
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x000a0	/* SODIMM 88 */
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x000a0 /* SODIMM 92 */
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100a0 /* SODIMM 90 */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX	0x1b020
+			MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpioblongrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TMS__GPIO1_IO11		0x30a0	/* SODIMM 71 */
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x10b0 /* SODIMM 77 */
+			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x70a0 /* SODIMM 99 */
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14	0x10b0 /* SODIMM 133 */
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24	0x10b0 /* SODIMM 135 */
+			MX6UL_PAD_UART3_CTS_B__GPIO1_IO26	0x10b0 /* SODIMM 100 */
+			MX6UL_PAD_JTAG_TRST_B__GPIO1_IO15	0x70a0 /* SODIMM 102 */
+			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07	0x10b0 /* SODIMM 104 */
+			MX6UL_PAD_UART3_RTS_B__GPIO1_IO27	0x10b0 /* SODIMM 186 */
+		>;
+	};
+
+	pinctrl_gpio2: gpio2grp { /* Camera */
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x10b0 /* SODIMM 69 */
+			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x10b0 /* SODIMM 75 */
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x10b0 /* SODIMM 85 */
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x10b0 /* SODIMM 96 */
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x10b0 /* SODIMM 98 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp { /* CAN2 */
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02	0x10b0 /* SODIMM 178 */
+			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x10b0 /* SODIMM 188 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x10b0 /* SODIMM 65 */
+		>;
+	};
+
+	pinctrl_gpio6: gpio6grp { /* Wifi pins */
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x10b0 /* SODIMM 89 */
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x10b0 /* SODIMM 79 */
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x10b0 /* SODIMM 81 */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x10b0 /* SODIMM 97 */
+			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x10b0 /* SODIMM 101 */
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x10b0 /* SODIMM 103 */
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x10b0 /* SODIMM 94 */
+		>;
+	};
+
+	pinctrl_gpio7: gpio7grp { /* CAN1 */
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0xb0b0/* SODIMM 55 */
+			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01	0xb0b0 /* SODIMM 63 */
+		>;
+	};
+
+	/*
+	 * With an eMMC instead of a raw NAND device the following pins
+	 * are available at SODIMM pins.
+	 */
+	pinctrl_gpmi_gpio: gpmigpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x10b0 /* SODIMM 140 */
+			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13	0x10b0 /* SODIMM 144 */
+			MX6UL_PAD_NAND_CLE__GPIO4_IO15		0x10b0 /* SODIMM 146 */
+			MX6UL_PAD_NAND_READY_B__GPIO4_IO12	0x10b0 /* SODIMM 142 */
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x100a9
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x100a9
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x100a9
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x100a9
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x100a9
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x100a9
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x100a9
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x100a9
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x100a9
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x100a9
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x100a9
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x100a9
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x100a9
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x100a9
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0	/* SODIMM 196 */
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0	/* SODIMM 194 */
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0	/* SODIMM 196 */
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0	/* SODIMM 194 */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001f8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001f8b0
+		>;
+	};
+
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x00079	/* SODIMM 76 */
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x00079	/* SODIMM 70 */
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x00079	/* SODIMM 60 */
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x00079	/* SODIMM 58 */
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x00079	/* SODIMM 78 */
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x00079	/* SODIMM 72 */
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x00079	/* SODIMM 80 */
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x00079	/* SODIMM 46 */
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x00079	/* SODIMM 62 */
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x00079	/* SODIMM 48 */
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x00079	/* SODIMM 74 */
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x00079	/* SODIMM 50 */
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x00079	/* SODIMM 52 */
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x00079	/* SODIMM 54 */
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x00079	/* SODIMM 66 */
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x00079	/* SODIMM 64 */
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x00079	/* SODIMM 57 */
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x00079	/* SODIMM 61 */
+		>;
+	};
+
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x00079	/* SODIMM 56 */
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x00079	/* SODIMM 44 */
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC    0x00079	/* SODIMM 68 */
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC    0x00079	/* SODIMM 82 */
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__PWM4_OUT	0x00079		/* SODIMM 59 */
+		>;
+	};
+
+	pinctrl_pwm5: pwm5grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__PWM5_OUT	0x00079		/* SODIMM 28 */
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_EN__PWM6_OUT	0x00079		/* SODIMM 30 */
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT	0x00079	/* SODIMM 67 */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DTE_RX	0x1b0b1	/* SODIMM 33 */
+			MX6UL_PAD_UART1_RX_DATA__UART1_DTE_TX	0x1b0b1	/* SODIMM 35 */
+			MX6UL_PAD_UART1_RTS_B__UART1_DTE_CTS	0x1b0b1	/* SODIMM 27 */
+			MX6UL_PAD_UART1_CTS_B__UART1_DTE_RTS	0x1b0b1	/* SODIMM 25 */
+		>;
+	};
+
+	pinctrl_uart1_ctrl1: uart1ctrl1grp { /* Additional DTR, DCD */
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x70a0 /* SODIMM 31 / DCD */
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x10b0 /* SODIMM 29 / DSR */
+			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x90b1 /* SODIMM 23 / DTR */
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x10b0 /* SODIMM 37 / RI */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX	0x1b0b1 /* SODIMM 36 */
+			MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX	0x1b0b1 /* SODIMM 38 */
+			MX6UL_PAD_UART2_CTS_B__UART2_DTE_RTS	0x1b0b1 /* SODIMM 32 */
+			MX6UL_PAD_UART2_RTS_B__UART2_DTE_CTS	0x1b0b1 /* SODIMM 34 */
+		>;
+	};
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__UART5_DTE_RX	0x1b0b1 /* SODIMM 19 */
+			MX6UL_PAD_GPIO1_IO05__UART5_DTE_TX	0x1b0b1 /* SODIMM 21 */
+		>;
+	};
+
+	pinctrl_usbh_reg: usbhreggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x10b0 /* SODIMM 129 / USBH_PEN */
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059 /* SODIMM 47 */
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059 /* SODIMM 190 */
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059 /* SODIMM 192 */
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059 /* SODIMM 49 */
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059 /* SODIMM 51 */
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059 /* SODIMM 53 */
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17069
+			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17069
+			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17069
+			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17069
+			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17069
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x10069
+
+			MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT	0x10
+		>;
+	};
+
+	pinctrl_usdhc2emmc: usdhc2emmcgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK     0x17059
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD     0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY    0x30b0
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl_atmel_snvs_conn: atmelsnvsconngrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04     0xb0a0	/* SODIMM 107 */
+		>;
+	};
+
+	pinctrl_snvs_gpio1: snvsgpio1grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x110a0	/* SODIMM 93 */
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x110a0	/* SODIMM 95 */
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x1b0a0	/* SODIMM 105 */
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0a0	/* SODIMM 131 / USBH_OC */
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x110a0	/* SODIMM 138 */
+		>;
+	};
+
+	pinctrl_snvs_gpio3: snvsgpio3grp { /* Wifi pins */
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x130a0	/* SODIMM 127 */
+		>;
+	};
+
+	pinctrl_snvs_ad7879_int: snvsad7879intgrp { /* TOUCH Interrupt */
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x100b0
+		>;
+	};
+
+	pinctrl_snvs_reg_sd: snvsregsdgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400100b0
+		>;
+	};
+
+	pinctrl_snvs_usbc_det: snvsusbcdetgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x130b0
+		>;
+	};
+
+	pinctrl_snvs_gpiokeys: snvsgpiokeysgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130a0	/* SODIMM 45 / WAKE_UP */
+		>;
+	};
+
+	pinctrl_snvs_usdhc1_cd: snvsusdhc1cdgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0a0 /* SODIMM 43 / MMC_CD */
+		>;
+	};
+
+	pinctrl_snvs_usdhc1_cd_sleep: snvsusdhc1cd-sleepgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x0
+		>;
+	};
+
+	pinctrl_snvs_wifi_pdn: snvswifipdngrp {
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x130a0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-drc02.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-drc02.dts
new file mode 100644
index 000000000000..b539975a872c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-drc02.dts
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * DRC02 PCB number: 568-100 or newer (2nd ethernet by SoM)
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+#include "imx6ull-dhcom-som-cfg-sdcard.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOM on DRC02";
+	compatible = "dh,imx6ull-dhcom-drc02", "dh,imx6ull-dhcom-som",
+		     "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+};
+
+/*
+ * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
+ * Therefore the UART RTS/CTS must be output on other DHCOM pins, see uart1
+ * node below.
+ */
+&can2 {
+	status = "okay";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "DRC02-In2",
+		"", "", "", "",
+		"", "", "DHCOM-I", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "DRC02-HW0", "DRC02-HW1", "DHCOM-M",
+		"DRC02-HW2", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the i.MX6ULL UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <25 0>; /* GPIO Q */
+		line-name = "rs485-rx-en";
+		output-low;
+	};
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "DHCOM-C", "DRC02-Out2",
+		"DHCOM-E", "", "", "DRC02-Out1",
+		"DRC02-In1", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+/* DHCOM I2C2 */
+&i2c1 {
+	eeprom@56 {
+		compatible = "atmel,24c04";
+		reg = <0x56>;
+		pagesize = <16>;
+	};
+};
+
+&uart1 {
+	/delete-property/ uart-has-rtscts;
+	rts-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+	cts-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; /* GPIO M */
+};
+
+/* Use UART as RS485 */
+&uart2 {
+	/delete-property/ uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rts-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* GPIO P */
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dts
new file mode 100644
index 000000000000..b29713831a74
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-RTC-WBT-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOM on Premium Developer Kit (2)";
+	compatible = "dh,imx6ull-dhcom-pdk2", "dh,imx6ull-dhcom-som",
+		     "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; /* GPIO G */
+		power-supply = <&reg_panel_3v3>;
+		pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* GPIO A */
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			wakeup-source;
+		};
+
+		button-1 {
+			gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; /* GPIO B */
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			wakeup-source;
+		};
+
+		button-2 {
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; /* GPIO C */
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			wakeup-source;
+		};
+
+		button-3 {
+			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; /* GPIO D */
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			wakeup-source;
+		};
+	};
+
+	led: led {
+		compatible = "gpio-leds";
+
+		/*
+		 * Disable PDK2 LED5, because GPIO E is
+		 * already used as touch interrupt.
+		 */
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <5>; /* PDK2 LED5 */
+			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; /* GPIO E */
+			status = "disabled";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <6>; /* PDK2 LED6 */
+			gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO F */
+		};
+
+		/*
+		 * Disable PDK2 LED7, because GPIO H is
+		 * already used for WiFi pin WL_REG_ON.
+		 */
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <7>; /* PDK2 LED7 */
+			gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; /* GPIO H */
+			status = "disabled";
+		};
+
+		/*
+		 * Disable PDK2 LED8, because GPIO I is
+		 * already used for BT pin BT_REG_ON.
+		 */
+		led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <8>; /* PDK2 LED8 */
+			gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+			status = "disabled";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+		power-supply = <&reg_panel_3v3>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	/* Filtered supply voltage */
+	reg_pdk2_24v: regulator-pdk2-24v {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <24000000>;
+		regulator-min-microvolt = <24000000>;
+		regulator-name = "24V_PDK2";
+	};
+
+	/* PDK2 U35 */
+	reg_pdk2_3v3: regulator-pdk2-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3V3_PDK2";
+		vin-supply = <&reg_pdk2_24v>;
+	};
+
+	/* 560-200 U1 */
+	reg_panel_3v3: regulator-panel-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3V3_PANEL";
+		vin-supply = <&reg_pdk2_24v>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "sgtl5000";
+		simple-audio-card,routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk_ext_audio_codec>;
+			sound-dai = <&sgtl5000>;
+		};
+	};
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&reg_pdk2_3v3>;
+		VDDIO-supply = <&reg_pdk2_3v3>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		power-supply = <&reg_panel_3v3>;
+	};
+};
+
+&lcdif {
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-picoitx.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-picoitx.dts
new file mode 100644
index 000000000000..e4cc2223583a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-picoitx.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * PicoITX PCB number: 487-600 or newer
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+#include "imx6ull-dhcom-som-cfg-sdcard.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOM on PicoITX";
+	compatible = "dh,imx6ull-dhcom-picoitx", "dh,imx6ull-dhcom-som",
+		     "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_YELLOW>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+		};
+	};
+};
+
+&fec1 {
+	phy-handle = <&mdio1_phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio1_phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+	};
+};
+
+&fec2 {
+	status = "disabled";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "PicoITX-HW2", "PicoITX-HW1", "DHCOM-M",
+		"PicoITX-HW0", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "PicoITX-In2", "PicoITX-Out2",
+		"PicoITX-In1", "", "", "PicoITX-Out1",
+		"DHCOM-G", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&iomuxc {
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b010
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b010
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som-cfg-sdcard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som-cfg-sdcard.dtsi
new file mode 100644
index 000000000000..040421f9c970
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som-cfg-sdcard.dtsi
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+/*
+ * Special SoM configuration: SD card
+ *
+ * Enabled:  Micro SD card on module or
+ *           external SD card via DHCOM depends on hardware variant
+ *           GPIO H and GPIO I will be available
+ *           DHCOM UART2 will be available
+ * Disabled: WiFi and BT
+ */
+
+/*
+ * To use usdhc1 as SD card, the WiFi node must be deleted.
+ * BT is also not available, so remove BT from the UART node.
+ */
+/delete-node/ &brcmf;
+/delete-node/ &bluetooth;
+
+/ {
+	aliases {
+		mmc1 = &usdhc1;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+	};
+
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VSD_3V3";
+	};
+};
+
+/* Micro SD card on module or external SD card via DHCOM */
+&usdhc1 {
+	/delete-property/ #address-cells;
+	/delete-property/ #size-cells;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ mmc-pwrseq;
+	/delete-property/ non-removable;
+	/delete-property/ wakeup-source;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	vmmc-supply = <&reg_sd1_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc1: usdhc1-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x120b0 /* SD1 CD */
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x120b0 /* SD1 CD */
+
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x120b0 /* SD1 CD */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
new file mode 100644
index 000000000000..830b5a5064f2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+	aliases {
+		/delete-property/ spi2;
+		/delete-property/ spi3;
+		i2c0 = &i2c2;
+		i2c1 = &i2c1;
+		mmc2 = &usdhc2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+		serial0 = &uart1;
+		serial1 = &uart6; /* DHCOM UART2, special hardware required */
+		serial2 = &uart3;
+		serial3 = &uart2; /* Use BT UART always as ttymxc3 */
+		serial4 = &uart4;
+		serial5 = &uart5;
+		spi0 = &ecspi1;
+		spi1 = &ecspi4; /* DHCOM SPI2, special hardware required */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_ext_3v3_ref: regulator-ext-3v3-ref {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3_REF";
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg1-vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg2-vbus";
+	};
+
+	/* SoM with WiFi/BT: WiFi pin WL_REG_ON is connected to a DHCOM GPIO */
+	/omit-if-no-ref/ usdhc1_pwrseq: usdhc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; /* GPIO H */
+	};
+};
+
+/* SoM with WiFi/BT: BT pin BT_REG_ON is connected to a DHCOM GPIO */
+&bluetooth {
+	shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+};
+
+&can1 {
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
+ * Only if this pins are used as CAN interface enable it on board layer.
+ */
+&can2 {
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM SPI1 */
+&ecspi1 {
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * DHCOM SPI2
+ * Special hardware required that uses the pins of FEC2. Therefore this SPI
+ * interface can only be used if FEC2 is disabled.
+ */
+&ecspi4 {
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM ETH1 */
+&fec1 {
+	phy-handle = <&mdio2_phy0>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* DHCOM ETH2 */
+&fec2 {
+	phy-handle = <&mdio2_phy1>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_fec2>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio2_phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+
+		mdio2_phy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec2_phy &pinctrl_snvs_fec2_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "DHCOM-INT",
+		"", "", "", "",
+		"", "", "DHCOM-I", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+	pinctrl-0 = <&pinctrl_spi1_switch
+		     &pinctrl_dhcom_i &pinctrl_dhcom_int>;
+	pinctrl-names = "default";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "DHCOM-L", "DHCOM-K", "DHCOM-M",
+		"DHCOM-J", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+	pinctrl-0 = <&pinctrl_dhcom_j &pinctrl_dhcom_k
+		     &pinctrl_dhcom_l &pinctrl_dhcom_m
+		     &pinctrl_dhcom_n &pinctrl_dhcom_o
+		     &pinctrl_dhcom_p &pinctrl_dhcom_q
+		     &pinctrl_dhcom_r &pinctrl_dhcom_s
+		     &pinctrl_dhcom_t &pinctrl_dhcom_u>;
+	pinctrl-names = "default";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "DHCOM-C", "DHCOM-D",
+		"DHCOM-E", "", "", "DHCOM-F",
+		"DHCOM-G", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+	pinctrl-0 = <&pinctrl_snvs_dhcom_a &pinctrl_snvs_dhcom_b
+		     &pinctrl_snvs_dhcom_c &pinctrl_snvs_dhcom_d
+		     &pinctrl_snvs_dhcom_e &pinctrl_snvs_dhcom_f
+		     &pinctrl_snvs_dhcom_g &pinctrl_snvs_dhcom_h>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM I2C2 */
+&i2c1 {
+	rtc_i2c: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH1 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	/* TI ADC101C027 */
+	adc@51 {
+		compatible = "ti,adc101c";
+		reg = <0x51>;
+		vref-supply = <&reg_ext_3v3_ref>;
+	};
+
+	/* TI ADC101C027 */
+	adc@52 {
+		compatible = "ti,adc101c";
+		reg = <0x52>;
+		vref-supply = <&reg_ext_3v3_ref>;
+	};
+
+	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH2 */
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-0 = <&pinctrl_lcdif>;
+	pinctrl-names = "default";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-names = "default";
+};
+
+&sai2 {
+	assigned-clock-rates = <320000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
+	pinctrl-0 = <&pinctrl_sai2>;
+	pinctrl-names = "default";
+};
+
+&tsc {
+	measure-delay-time = <0xffff>;
+	pinctrl-0 = <&pinctrl_tsc>;
+	pinctrl-names = "default";
+	pre-charge-time = <0xfff>;
+	touchscreen-average-samples = <32>;
+	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+};
+
+/* DHCOM UART1 */
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * DHCOM UART2 (alternative)
+ * Special hardware required that uses DHCOM GPIO pins for DHCOM UART2.
+ * Therefore this UART interface can only be used if DHCOM GPIOs J/K/L/M are
+ * removed from GPIO hog muxing.
+ */
+&uart6 {
+	pinctrl-0 = <&pinctrl_uart6>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&usbotg1 {
+	adp-disable;
+	disable-over-current;
+	dr_mode = "otg";
+	hnp-disable;
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	pinctrl-names = "default";
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current; /* Overcurrent pin is used for TSC */
+	dr_mode = "host";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	pinctrl-names = "default";
+	tpl-support;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+};
+
+/* eMMC on module */
+&usdhc2 {
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&iomuxc {
+	/* DHCOM GPIOs I..U + INT_HIGHEST_PRIORITY */
+	pinctrl_dhcom_i: dhcom-i-grp {
+		fsl,pins = <MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_j: dhcom-j-grp {
+		fsl,pins = <MX6UL_PAD_CSI_HSYNC__GPIO4_IO20	0x400120b0>;
+	};
+
+	pinctrl_dhcom_k: dhcom-k-grp {
+		fsl,pins = <MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_l: dhcom-l-grp {
+		fsl,pins = <MX6UL_PAD_CSI_MCLK__GPIO4_IO17	0x400120b0>;
+	};
+
+	pinctrl_dhcom_m: dhcom-m-grp {
+		fsl,pins = <MX6UL_PAD_CSI_VSYNC__GPIO4_IO19	0x400120b0>;
+	};
+
+	pinctrl_dhcom_n: dhcom-n-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x400120b0>;
+	};
+
+	pinctrl_dhcom_o: dhcom-o-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x400120b0>;
+	};
+
+	pinctrl_dhcom_p: dhcom-p-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x400120b0>;
+	};
+
+	pinctrl_dhcom_q: dhcom-q-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x400120b0>;
+	};
+
+	pinctrl_dhcom_r: dhcom-r-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x400120b0>;
+	};
+
+	pinctrl_dhcom_s: dhcom-s-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x400120b0>;
+	};
+
+	pinctrl_dhcom_t: dhcom-t-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x400120b0>;
+	};
+
+	pinctrl_dhcom_u: dhcom-u-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x400120b0>;
+	};
+
+	pinctrl_dhcom_int: dhcom-int-grp {
+		fsl,pins = <MX6UL_PAD_JTAG_TMS__GPIO1_IO11	0x400120b0>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO	0x100b1
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI	0x100b1
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK	0x100b1
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			/* FEC1 uses MDIO bus from FEC2 */
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b010
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b010
+		>;
+	};
+
+	pinctrl_fec1_phy: fec1-phy-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0xb0 /* SMSC PHY reset */
+		>;
+	};
+
+	pinctrl_fec2: fec2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
+		>;
+	};
+
+	pinctrl_fec2_phy: fec2-phy-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24	0xb0 /* SMSC PHY reset */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x4001b8b0
+		>;
+	};
+
+	pinctrl_lcdif: lcdif-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+		>;
+	};
+
+	pinctrl_pwm1: pwm1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__PWM1_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_sai2: sai2-grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
+	pinctrl_tsc: tsc-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6: uart6-grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x120b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B	0x17059 /* SD2 Reset */
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	/* DHCOM GPIOs A..H */
+	pinctrl_snvs_dhcom_a: snvs-dhcom-a-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_b: snvs-dhcom-b-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_c: snvs-dhcom-c-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_d: snvs-dhcom-d-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_e: snvs-dhcom-e-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_f: snvs-dhcom-f-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_g: snvs-dhcom-g-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_h: snvs-dhcom-h-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400120b0>;
+	};
+
+	pinctrl_snvs_fec1_phy: snvs-fec1-phy-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0xb1 /* SMSC PHY Int */
+		>;
+	};
+
+	pinctrl_snvs_fec2_phy: snvs-fec2-phy-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0xb1 /* SMSC PHY Int */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-maveo-box.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-maveo-box.dts
new file mode 100644
index 000000000000..047f7b2d8526
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-maveo-box.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ * Copyright (C) 2023 Marantec electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCR-iMX6ULL-C080-R051-SPI-WBT-I-01LG
+ * DHCOR PCB number: 578-200 or newer
+ * maveo box PCB number: 525-200 or newer
+ */
+
+/dts-v1/;
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOR on maveo box";
+	compatible = "marantec,imx6ull-dhcor-maveo-box", "dh,imx6ull-dhcor-som",
+		     "fsl,imx6ull";
+
+	aliases {
+		mmc2 = &usdhc2;
+		spi0 = &ecspi4;
+		spi3 = &ecspi1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg1-vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg2-vbus";
+	};
+
+	/* WiFi pin WL_REG_ON is connected to GPIO 5.9 */
+	usdhc1_pwrseq: usdhc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* BT pin BT_REG_ON is connected to GPIO 1.18 */
+&bluetooth {
+	shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+};
+
+/* X10 connector */
+&ecspi4 {
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	spidev@0 {
+		compatible = "dh,dhcom-board";
+		reg = <0>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <54000000>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "BUTTON-USER", "", "",
+		"BUTTON-RESET", "", "", "",
+		"", "", "", "",
+		"", "", "BT-REG-ON", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"PSOC-GPIO-1", "", "", "X10-12",
+		"X10-10", "PSOC-GPIO-2", "PSOC-GPIO-3", "",
+		"X10-11", "X10-9", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"DHCOR-HW0", "DHCOR-HW1", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "MAVEO-BOX-HW0", "LED-G", "MAVEO-BOX-VAR1",
+		"MAVEO-BOX-VAR0", "MAVEO-BOX-HW1", "MAVEO-BOX-HW2", "LED-B",
+		"LED-R", "", "", "",
+		"", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"PSOC-SWD-IO", "PSOC-SWD-CLK", "PSOC-RESET", "ZIGBEE-PROG",
+		"ZIGBEE-RESET", "", "PSOC-PWR-FAIL-OUT", "NFC-ENABLE",
+		"NFC-IRQ", "WL-REG-ON", "DHCOR-BOOT-M0", "DHCOR-BOOT-M1",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+/* Console UART */
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* BT on LGA */
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt_gpio>;
+};
+
+/* Zigbee UART */
+&uart3 {
+	pinctrl-0 = <&pinctrl_uart3 &pinctrl_snvs_zigbee_gpio>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg1 {
+	adp-disable;
+	disable-over-current; /* Overcurrent pin isn't connected */
+	dr_mode = "otg";
+	hnp-disable;
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	pinctrl-names = "default";
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current; /* Overcurrent pin isn't connected */
+	dr_mode = "host";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	pinctrl-names = "default";
+	tpl-support;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+	pinctrl-0 = <&pinctrl_usdhc1_wifi &pinctrl_snvs_wifi_gpio>;
+};
+
+/* eMMC */
+&usdhc2 {
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog_maveo_box>;
+	pinctrl-names = "default";
+
+	pinctrl_hog_maveo_box: hog-maveo-box-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x120b0    /* BUTTON_USER */
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x120b0    /* BUTTON_RESET */
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x400120b0 /* LED_G */
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x400120b0 /* LED_B */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x400120b0 /* LED_R */
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x400120b0 /* X10_9 */
+			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0x400120b0 /* X10_10 */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x400120b0 /* X10_11 */
+			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x400120b0 /* X10_12 */
+			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0x400120b0 /* PSOC_GPIO_1 */
+			MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05	0x400120b0 /* PSOC_GPIO_2 */
+			MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06	0x400120b0 /* PSOC_GPIO_3 */
+			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x120b0    /* MAVEO_BOX_HW0 */
+			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x120b0    /* MAVEO_BOX_HW1 */
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x120b0    /* MAVEO_BOX_HW2 */
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x120b0    /* MAVEO_BOX_VAR0 */
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x120b0    /* MAVEO_BOX_VAR1 */
+			MX6UL_PAD_LCD_CLK__GPIO3_IO00		0x120b0    /* DHCOR_HW0 */
+			MX6UL_PAD_LCD_ENABLE__GPIO3_IO01	0x120b0    /* DHCOR_HW1 */
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0x120b0
+			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0x120b0
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0x120b0
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0x120b0
+			MX6UL_PAD_LCD_DATA04__GPIO3_IO09	0x120b0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x120b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x120b0
+			MX6UL_PAD_LCD_DATA07__GPIO3_IO12	0x120b0
+			MX6UL_PAD_LCD_DATA08__GPIO3_IO13	0x120b0
+			MX6UL_PAD_LCD_DATA09__GPIO3_IO14	0x120b0
+			MX6UL_PAD_LCD_DATA10__GPIO3_IO15	0x120b0
+			MX6UL_PAD_LCD_DATA11__GPIO3_IO16	0x120b0
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17	0x120b0
+			MX6UL_PAD_LCD_DATA13__GPIO3_IO18	0x120b0
+			MX6UL_PAD_LCD_DATA14__GPIO3_IO19	0x120b0
+			MX6UL_PAD_LCD_DATA15__GPIO3_IO20	0x120b0
+			MX6UL_PAD_LCD_DATA16__GPIO3_IO21	0x120b0
+			MX6UL_PAD_LCD_DATA17__GPIO3_IO22	0x120b0
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x120b0
+		>;
+	};
+
+	pinctrl_bt_gpio: bt-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x400120b0 /* BT_REG_ON */
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO	0x100b1
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI	0x100b1
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK	0x100b1
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x4001b8b0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_READY_B__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_NAND_CE0_B__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x120b0 /* USB_OTG1_PWR */
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x120b0 /* USB_OTG2_PWR */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B	0x17059 /* SD2 Reset */
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-0 = <&pinctrl_snvs_hog_maveo_box>;
+	pinctrl-names = "default";
+
+	pinctrl_snvs_hog_maveo_box: snvs-hog-maveo-box-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x400120b0 /* PSOC_SWD_IO */
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x400120b0 /* PSOC_SWD_CLK */
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x400120b0 /* PSOC_RESET */
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x400120b0 /* PSOC_PWR_FAIL_OUT */
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x400120b0 /* NFC_ENABLE */
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x400120b0 /* NFC_IRQ */
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x120b0    /* DHCOR_BOOT_M0 */
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x120b0    /* DHCOR_BOOT_M1 */
+		>;
+	};
+
+	pinctrl_snvs_wifi_gpio: snvs-wifi-gpio-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400120b0 /* WL_REG_ON */
+		>;
+	};
+
+	pinctrl_snvs_zigbee_gpio: snvs-zigbee-gpio-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x400120b0 /* ZIGBEE_PROG */
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x400120b0 /* ZIGBEE_RESET */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-som.dtsi
new file mode 100644
index 000000000000..45315adfaa86
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-som.dtsi
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/regulator/dlg,da9063-regulator.h>
+#include "imx6ull.dtsi"
+
+/ {
+	aliases {
+		/delete-property/ mmc0;
+		/delete-property/ mmc1;
+	};
+
+	memory@80000000 {
+		/* Appropriate memory size will be filled by U-Boot */
+		reg = <0x80000000 0>;
+		device_type = "memory";
+	};
+};
+
+&cpu0 {
+	/*
+	 * Due to the design as a solderable SOM, there are no capacitors
+	 * below the SoC, therefore higher voltages are required.
+	 */
+	operating-points = <
+		/* kHz	uV */
+		900000	1275000
+		792000	1250000 /* Voltage increased */
+		528000	1175000
+		396000	1025000
+		198000	950000
+	>;
+	fsl,soc-operating-points = <
+		/* KHz	uV */
+		900000	1250000
+		792000	1250000 /* Voltage increased */
+		528000	1175000
+		396000	1175000
+		198000	1175000
+	>;
+};
+
+&gpio1 {
+	pinctrl-0 = <&pinctrl_spi1_switch>;
+	pinctrl-names = "default";
+	/*
+	 * Pin SPI_BOOT_FLASH_EN (GPIO 1.9) is a switch for either using the
+	 * DHCOM SPI1 interface or accessing the SPI bootflash. Both using
+	 * ecspi1, but muxed to different pins. The DHCOM SPI1 interface uses
+	 * the pins PAD_LCD_DATA21..23 and the SPI bootflash uses the pins
+	 * PAD_CSI_DATA04..07. If the SPI bootflash is enabled the pins for
+	 * DHCOM GPIOs N/O/P/Q/R/S/T/U aren't usable anymore, because they
+	 * are used for the bus interface to the SPI bootflash. The GPIOs are
+	 * disconnected by a buffer which is also controlled via the pin
+	 * SPI_BOOT_FLASH_EN. Therefore the access to the bootflash is a
+	 * special case and is disabled by setting GPIO 1.9 to high.
+	 */
+	spi1-switch-hog {
+		gpio-hog;
+		gpios = <9 0>;
+		output-high;
+		line-name = "spi1-switch";
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic@58 {
+		compatible = "dlg,da9061";
+		reg = <0x58>;
+
+		onkey {
+			compatible = "dlg,da9061-onkey", "dlg,da9062-onkey";
+			status = "disabled";
+		};
+
+		regulators {
+			vdd_soc_in_1v4: buck1 {
+				regulator-allowed-modes = <DA9063_BUCK_MODE_SLEEP>; /* PFM */
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SLEEP>;
+				regulator-max-microvolt = <1400000>;
+				regulator-min-microvolt = <1400000>;
+				regulator-name = "vdd_soc_in_1v4";
+			};
+
+			vcc_3v3: buck2 {
+				regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "vcc_3v3";
+			};
+
+			/*
+			 * The current DRR3 memory can be supplied with a
+			 * voltage of either 1.35V or 1.5V. For reasons of
+			 * backward compatibility to only 1.5V DDR3 memory,
+			 * the voltage is set to 1.5V.
+			 */
+			vcc_ddr_1v35: buck3 {
+				regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+				regulator-max-microvolt = <1500000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-name = "vcc_ddr_1v35";
+			};
+
+			vcc_2v5: ldo1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2500000>;
+				regulator-min-microvolt = <2500000>;
+				regulator-name = "vcc_2v5";
+			};
+
+			vdd_snvs_in_3v3: ldo2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "vdd_snvs_in_3v3";
+			};
+
+			vcc_1v8: ldo3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vcc_1v8";
+			};
+
+			vcc_1v2: ldo4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <1200000>;
+				regulator-name = "vcc_1v2";
+			};
+		};
+
+		thermal {
+			compatible = "dlg,da9061-thermal", "dlg,da9062-thermal";
+			status = "disabled";
+		};
+
+		watchdog {
+			compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
+			status = "disabled";
+		};
+	};
+};
+
+&ocotp {
+	/* Don't get write access by default */
+	read-only;
+};
+
+&reg_arm {
+	vin-supply = <&vdd_soc_in_1v4>;
+};
+
+&reg_soc {
+	vin-supply = <&vdd_soc_in_1v4>;
+};
+
+/* BT on LGA (BT_REG_ON is connected to LGA pin E1) */
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+
+	/*
+	 * Actually, the maximum speed of the chip is 4MBdps, but there are
+	 * limitations that prevent this speed. It hasn't yet been figured out
+	 * what the reason for this is. Currently, the maximum speed of 3MBdps
+	 * can be used without any problems. If the limitation can be overcome,
+	 * the speed can be increased accordingly.
+	 */
+	bluetooth: bluetooth {
+		compatible = "brcm,bcm43430a1-bt"; /* muRata 1DX */
+		max-speed = <3000000>;
+		vbat-supply = <&vcc_3v3>;
+		vddio-supply = <&vcc_3v3>;
+	};
+};
+
+/* WiFi on LGA (WL_REG_ON is connected to LGA pin E3) */
+&usdhc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	pinctrl-0 = <&pinctrl_usdhc1_wifi>;
+	pinctrl-names = "default";
+	wakeup-source;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac"; /* muRata 1DX */
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL	0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28	0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29	0x4001b8b0
+		>;
+	};
+
+	pinctrl_spi1_switch: spi1-switch-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x120b0 /* SPI_BOOT_FLASH_EN */
+		>;
+	};
+
+	pinctrl_uart2: uart2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS	0x1b0b1
+			MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1_wifi: usdhc1-wifi-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x1b0b0
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10010
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x1b0b0
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x1b0b0
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x1b0b0
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-jozacp.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-jozacp.dts
new file mode 100644
index 000000000000..a152eeb78e88
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-jozacp.dts
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2020 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6ull.dtsi"
+
+/ {
+	model = "JOZ Access Point";
+	compatible = "joz,jozacp", "fsl,imx6ull";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	/* On board name LED_RGB1 */
+	led-controller-1 {
+		compatible = "pwm-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <0>;
+			pwms = <&pwm1 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			pwms = <&pwm3 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <2>;
+			pwms = <&pwm5 0 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	/* On board name LED_RGB2 */
+	led-controller-2 {
+		compatible = "pwm-leds";
+
+		led-3 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <3>;
+			pwms = <&pwm2 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-4 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <4>;
+			pwms = <&pwm4 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-5 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <5>;
+			pwms = <&pwm6 0 10000000 0>;
+			max-brightness = <255>;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_5v0>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vbus: regulator-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vbus>;
+		regulator-name = "vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v0>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usdhc2_wifi_pwrseq: usdhc2-wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		reset-gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+			interrupts-extended = <&gpio1 29 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&pwm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm5>;
+	status = "okay";
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	status = "okay";
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	dtr-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	vbus-supply = <&reg_vbus>;
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	vmmc-supply = <&reg_3v3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	cap-mmc-hw-reset;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+	bus-width = <4>;
+	no-1-8-v;
+	no-mmc;
+	no-sd;
+	non-removable;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC	 0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28	0x038b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29	0x170b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* HW Revision */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x1b0b0
+
+			/* HW ID */
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0
+
+			/* Digital inputs */
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x11000
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x11000
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x11000
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x11000
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x11000
+
+			/* Isolated outputs */
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x01020
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x01020
+			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23	0x01020
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24	0x01020
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x01020
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001f8b1
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001f8b1
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001f8b1
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__PWM1_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__PWM2_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA02__PWM3_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__PWM4_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm5: pwm5grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__PWM5_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA19__PWM6_OUT		0x01010
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DCE_TX		0x1b0b0
+			MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX	0x1b0b0
+			MX6UL_PAD_LCD_HSYNC__UART4_DCE_CTS	0x1b0b0
+			MX6UL_PAD_LCD_VSYNC__UART4_DCE_RTS	0x1b0b0
+			MX6UL_PAD_LCD_RESET__GPIO3_IO04		0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC	0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__USDHC1_RESET_B	0x17099
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x1f099
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10099
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17099
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17099
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17099
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17099
+			MX6UL_PAD_NAND_READY_B__USDHC1_DATA4	0x17099
+			MX6UL_PAD_NAND_CE0_B__USDHC1_DATA5	0x17099
+			MX6UL_PAD_NAND_CE1_B__USDHC1_DATA6	0x17099
+			MX6UL_PAD_NAND_CLE__USDHC1_DATA7	0x17099
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x100b9
+			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x170b9
+			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_vbus: vbus0grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x030b0
+		>;
+	};
+
+	pinctrl_wifi_npd: wifigrp {
+		fsl,pins = <
+			/* WL_REG_ON */
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x03020
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_hog>;
+
+	pinctrl_snvs_hog: snvs-hog-grp {
+		fsl,pins = <
+			/* Digital outputs */
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x00020
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x00020
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x00020
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x00020
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x00020
+
+			/* Digital outputs fault feedback */
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17000
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17000
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x17000
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x17000
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x17000
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dts
new file mode 100644
index 000000000000..fa016465cdbc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ull-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
+
+/ {
+	model = "Kontron BL i.MX6ULL (N641X S)";
+	compatible = "kontron,bl-imx6ull", "kontron,sl-imx6ull", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-sl.dtsi
new file mode 100644
index 000000000000..93f10eb3494f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-sl.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+	model = "Kontron SL i.MX6ULL (N641X SOM)";
+	compatible = "kontron,sl-imx6ull", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx-eval.dts
new file mode 100644
index 000000000000..79cc45728cd2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx-eval.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-myir-mys-6ulx.dtsi"
+
+/ {
+	model = "MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND";
+	compatible = "myir,imx6ull-mys-6ulx-eval", "fsl,imx6ull";
+};
+
+&gpmi {
+	fsl,use-minimum-ecc;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx.dtsi
new file mode 100644
index 000000000000..d03694feaf5c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx.dtsi
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "MYiR MYS-6ULX Single Board Computer";
+	compatible = "fsl,imx6ull";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_vdd_5v: regulator-vdd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_vdd_3v3: regulator-vdd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_vdd_5v>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_vdd_3v3>;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_vdd_3v3>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	keep-power-in-suspend;
+	vmmc-supply = <&reg_vdd_3v3>;
+};
+
+&iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x0b0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170b9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170b9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170b9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-opos6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6ul.dtsi
index 155f941f2811..155f941f2811 100644
--- a/arch/arm/boot/dts/imx6ull-opos6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6ul.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-opos6uldev.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6uldev.dts
index 198fdb72641b..198fdb72641b 100644
--- a/arch/arm/boot/dts/imx6ull-opos6uldev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6uldev.dts
diff --git a/arch/arm/boot/dts/imx6ull-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-phycore-som.dtsi
index 56cd16e5a77f..56cd16e5a77f 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-emmc.dts
index 9648d4ecaf58..8e2a4c5d7765 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-emmc.dts
@@ -9,6 +9,7 @@
 #include "imx6ull-phytec-phycore-som.dtsi"
 #include "imx6ull-phytec-segin.dtsi"
 #include "imx6ull-phytec-segin-peb-eval-01.dtsi"
+#include "imx6ull-phytec-segin-peb-av-02.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 ULL Full Featured with eMMC";
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-nand.dts
index 656baf846453..1d7362b5ac91 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-nand.dts
@@ -9,6 +9,8 @@
 #include "imx6ull-phytec-phycore-som.dtsi"
 #include "imx6ull-phytec-segin.dtsi"
 #include "imx6ull-phytec-segin-peb-eval-01.dtsi"
+#include "imx6ull-phytec-segin-peb-av-02.dtsi"
+#include "imx6ull-phytec-segin-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 ULL Full Featured with NAND";
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-lc-rdk-nand.dts
index e168494e0a6d..4bcbae024d8d 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-lc-rdk-nand.dts
@@ -9,6 +9,7 @@
 #include "imx6ull-phytec-phycore-som.dtsi"
 #include "imx6ull-phytec-segin.dtsi"
 #include "imx6ull-phytec-segin-peb-eval-01.dtsi"
+#include "imx6ull-phytec-segin-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 ULL Low Cost with NAND";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-av-02.dtsi
new file mode 100644
index 000000000000..06bb7f327780
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-av-02.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Stefan Riedmueller <s.riedmueller@phytec.de>
+ */
+
+#include "imx6ul-phytec-segin-peb-av-02.dtsi"
+
+&iomuxc {
+	/delete-node/ edtft5406grp;
+	/delete-node/ stmpegrp;
+};
+
+&iomuxc_snvs {
+	pinctrl_edt_ft5406: edtft5406grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-eval-01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-eval-01.dtsi
index ff08d95a1aa2..ff08d95a1aa2 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-eval-01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-eval-01.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-wlbt-05.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-wlbt-05.dtsi
new file mode 100644
index 000000000000..df25814a3371
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-wlbt-05.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include "imx6ul-phytec-segin-peb-wlbt-05.dtsi"
+
+&iomuxc {
+	/delete-node/ wlgrp;
+};
+
+&iomuxc_snvs {
+	pinctrl_wl: wlgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x3031
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin.dtsi
index c1595fc785f7..e287a0453b5f 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin.dtsi
@@ -14,7 +14,6 @@
 &iomuxc {
 	/delete-node/ flexcan1engrp;
 	/delete-node/ rtcintgrp;
-	/delete-node/ stmpegrp;
 };
 
 &iomuxc_snvs {
@@ -29,10 +28,4 @@
 			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
 		>;
 	};
-
-	pinctrl_stmpe: stmpegrp {
-		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dts
new file mode 100644
index 000000000000..1610f3892d9e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri-emmc",
+		     "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* EMMC-Version */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-nand.dts
new file mode 100644
index 000000000000..92e7d38d5637
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-nand.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri-nand",
+		     "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* NAND-Version */
+&gpmi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri.dtsi
new file mode 100644
index 000000000000..44cc4ff1d0df
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri.dtsi
@@ -0,0 +1,582 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-phytec-phycore-som.dtsi"
+
+/ {
+	aliases {
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-key";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key {
+			label = "KEY-A";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_A>;
+			wakeup-source;
+		};
+	};
+
+	reg_adc1_vref_3v3: regulator-vref-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_s25fl064_hold: regulator-s25fl064-hold {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_s25fl064_hold>;
+		compatible = "regulator-fixed";
+		regulator-name = "s25fl064_hold";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb_hub_vbus: regulator-hub-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbhubpwr>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_hub_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1pwr>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	user_leds: user-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_user_leds>,
+			    <&pinctrl_user_leds_snvs>;
+
+		user-led1 {
+			label = "yellow";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "off";
+		};
+
+		user-led2 {
+			label = "red";
+			gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "off";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>,
+		    <&pinctrl_ecspi1_cs>;
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>,
+		   <&gpio3 10 GPIO_ACTIVE_LOW>,
+		   <&gpio3 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	tpm_tis: tpm@1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tpm>;
+		compatible = "tcg,tpm_tis-spi";
+		reg = <1>;
+		spi-max-frequency = <20000000>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	s25fl064: flash@2 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = " jedec,spi-nor";
+		reg = <2>;
+		spi-max-frequency = <40000000>;
+		m25p,fast-read;
+		status = "disabled";
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+	dmas = <&sdma 7 8 0>,
+	       <&sdma 8 8 0>;
+	dma-names = "rx", "tx";
+	status = "okay";
+};
+
+&ethphy1 {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	tmp102: tmp@49 {
+		compatible = "ti,tmp102";
+		reg = <0x49>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tempsense>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		#thermal-sensor-cells = <1>;
+	};
+
+	i2c_rtc: rtc@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	sda-gpios = <&gpio3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio3 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&mdio {
+	ethphy2: ethernet-phy@2 {
+		reg = <2>;
+		micrel,led-mode = <1>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+		clock-names = "rmii-ref";
+		status = "okay";
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* UART4 * RS485  */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	rts-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+/* UART5 * RS232  */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart7>;
+	status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_hub_vbus>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "disabled";
+};
+
+&iomuxc_snvs {
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+
+	pinctrl_tempsense: tempsensegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17059
+		>;
+	};
+
+	pinctrl_tpm: tpmgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x17059
+		>;
+	};
+
+	pinctrl_usbhubpwr: usbhubpwrgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x17059
+		>;
+	};
+
+	pinctrl_user_leds_snvs: user_ledsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x79
+		>;
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x17059  /* nUART_MUX_RS232 */
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x17059  /* nUART_MUX_DUAL_RX_TX */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x79
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK	0x100b1
+			MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO	0x100b1
+			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI	0x100b1
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x10b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi1_cs: ecspi1csgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x10b0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x10b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x10b0
+		>;
+	};
+
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x0b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA10__FLEXCAN2_TX	0x0b0b0
+			MX6UL_PAD_LCD_DATA11__FLEXCAN2_RX	0x0b0b0
+		>;
+	};
+
+	princtrl_flexcan2_en: flexcan2engrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x17059
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__I2C2_SCL	0xb0
+			MX6UL_PAD_GPIO1_IO01__I2C2_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00	0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__I2C3_SCL	0xb0
+			MX6UL_PAD_LCD_DATA00__I2C3_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0xb0
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0xb0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__I2C4_SCL	0xb0
+			MX6UL_PAD_LCD_DATA02__I2C4_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0xb0
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0xb0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__PWM6_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_s25fl064_hold: s25fl064holdgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17	0x100b1
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
+			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DCE_TX		0x1b0b1
+			MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX	0x1b0b1
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart7: uart7grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA16__UART7_DCE_TX	0x1b0b1
+			MX6UL_PAD_LCD_DATA17__UART7_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x80
+		>;
+	};
+
+	pinctrl_usbotg1pwr: usbotg1pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_user_leds: userledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x79
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc-snvs.h
index 54cfe72295aa..54cfe72295aa 100644
--- a/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc-snvs.h
diff --git a/arch/arm/boot/dts/imx6ull-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc.h
index eb025a9d4759..7328d4ef8559 100644
--- a/arch/arm/boot/dts/imx6ull-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc.h
@@ -82,6 +82,6 @@
 #define MX6ULL_PAD_CSI_DATA04__ESAI_TX_FS                         0x01F4 0x0480 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA05__ESAI_TX_CLK                        0x01F8 0x0484 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA06__ESAI_TX5_RX0                       0x01FC 0x0488 0x0000 0x9 0x0
-#define MX6ULL_PAD_CSI_DATA07__ESAI_T0                            0x0200 0x048C 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA07__ESAI_TX0                           0x0200 0x048C 0x0000 0x9 0x0
 
 #endif /* __DTS_IMX6ULL_PINFUNC_H */
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-common.dtsi
new file mode 100644
index 000000000000..3fdece5bd31f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-common.dtsi
@@ -0,0 +1,852 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx6ull.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &usdhc2; /* eMMC */
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-0 = <&pinctrl_emmc_rst>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_dcdc_3v3: regulator-dcdc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "dcdc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_status_leds>;
+
+		led-1 {
+			function = LED_FUNCTION_BOOT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_PROGRAMMING;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_motor
+		     &pinctrl_adc_cp
+		     &pinctrl_adc_pp>;
+	vref-supply = <&vgen1_reg>;
+	status = "okay";
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <3>;
+	cs-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH
+		    &gpio3 2  GPIO_ACTIVE_HIGH
+		    &gpio3 4  GPIO_ACTIVE_HIGH>;
+};
+
+&ecspi4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	num-cs = <1>;
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1
+		     &pinctrl_enet1_phy_rst
+		     &pinctrl_enet_mdio>;
+	phy-supply = <&reg_dcdc_3v3>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet1_phy_int>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&gpio2 7 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+			max-speed = <100>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "CP_INVERT",
+			  "",
+			  "",				/* 15 */
+			  "",
+			  "",
+			  "",
+			  "MOTOR_1_FAULT_N",
+			  "",				/* 20 */
+			  "",
+			  "ROTARY_SWITCH_1_2_N",
+			  "ROTARY_SWITCH_1_4_N",
+			  "ROTARY_SWITCH_1_8_N",
+			  "MOTOR_2_FAULT_N";		/* 25 */
+};
+
+&gpio3 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "EXT_GPIO",
+			  "MOTOR_1_DRIVER_IN1_N",
+			  "MOTOR_1_DRIVER_IN2",
+			  "MOTOR_2_DRIVER_IN1",
+			  "STM32_BOOT0",		/* 10 */
+			  "STM32_RST_N",
+			  "RELAY_1_ENABLE",
+			  "RELAY_2_ENABLE",
+			  "",
+			  "",				/* 15 */
+			  "QCA700X_MAINS_BOOTLOADER_N",
+			  "QCA700X_CP_RST_N",
+			  "QCA700X_CP_BOOTLOADER_N",
+			  "",
+			  "DIGITAL_OUT_1",		/* 20 */
+			  "DIGITAL_OUT_2",
+			  "DIGITAL_OUT_3",
+			  "DIGITAL_OUT_4",
+			  "DIGITAL_OUT_5",
+			  "DIGITAL_OUT_6",		/* 25 */
+			  "ROTARY_SWITCH_2_8_N",
+			  "ROTARY_SWITCH_2_4_N",
+			  "ROTARY_SWITCH_2_2_N";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "BOARD_VARIANT_1",
+			  "BOARD_VARIANT_2",
+			  "BOARD_VARIANT_0",		/* 15 */
+			  "BOARD_VARIANT_3",
+			  "",
+			  "ROTARY_SWITCH_2_1_N",
+			  "",
+			  "DIGITAL_IN_5",		/* 20 */
+			  "",
+			  "",
+			  "DIGITAL_IN_6",
+			  "",
+			  "DIGITAL_IN_1",		/* 25 */
+			  "DIGITAL_IN_2",
+			  "DIGITAL_IN_4",
+			  "DIGITAL_IN_3";
+
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <19 0>;
+		input;
+	};
+};
+
+&gpio5 {
+	gpio-line-names = "ROTARY_SWITCH_1_1_N",	/* 0 */
+			  "",
+			  "RELAY_2_SENSE",
+			  "RELAY_1_SENSE",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "QCA700X_MAINS_RST_N",
+			  "MOTOR_2_DRIVER_IN2",
+			  "",
+			  "CP_POSITIVE_PEAK_RST",	/* 10 */
+			  "CP_NEGATIVE_PEAK_RST";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3001: pmic@8 {
+		compatible = "fsl,pfuze3001";
+		reg = <0x08>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-name = "SW1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "SW2";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-name = "SW3";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-name = "VSNVS";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-name = "VLDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-name = "VLDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-name = "VCCSD";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-name = "V33";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-name = "VLDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-name = "VLDO4";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	onewire@18 {
+		compatible = "maxim,ds2484";
+		reg = <0x18>;
+	};
+
+	accelerometer@19 {
+		compatible = "st,iis328dq", "st,h3lis331dl-accel";
+		reg = <0x19>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accelerometer_int1_snvs>;
+		vdd-supply = <&reg_dcdc_3v3>;
+		vddio-supply = <&reg_dcdc_3v3>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <5 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_board_var
+		     &pinctrl_digital_input
+		     &pinctrl_digital_output
+		     &pinctrl_gpio_motor
+		     &pinctrl_hog_pins
+		     &pinctrl_rotary_switch1
+		     &pinctrl_rotary_switch2>;
+
+	pinctrl_adc_cp: adc-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02            0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03            0xb0
+		>;
+	};
+
+	pinctrl_adc_motor: adc-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00            0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01            0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04            0xb0
+		>;
+	};
+
+	pinctrl_adc_pp: adc-ppgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05            0xb0
+		>;
+	};
+
+	pinctrl_board_var: board-vargrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__GPIO4_IO15              0xb0
+			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13            0xb0
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14            0xb0
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16              0xb0
+		>;
+	};
+
+	pinctrl_digital_input: digital-inputgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25            0xb0
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26            0xb0
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28            0xb0
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27            0xb0
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20             0xb0
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23            0xb0
+		>;
+	};
+
+	pinctrl_digital_output: digital-outputgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA15__GPIO3_IO20            0x400000b0
+			MX6UL_PAD_LCD_DATA16__GPIO3_IO21            0x400000b0
+			MX6UL_PAD_LCD_DATA17__GPIO3_IO22            0x400000b0
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23            0x400000b0
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24            0x400000b0
+			MX6UL_PAD_LCD_DATA20__GPIO3_IO25            0x400000b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29         0x10b0
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02             0xb0
+			MX6UL_PAD_LCD_RESET__GPIO3_IO04             0xb0
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK        0x10b0
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO        0x10b0
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI        0x10b0
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15           0x10b0
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK       0x10b0
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO         0x10b0
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI          0x10b0
+		>;
+	};
+
+	pinctrl_emmc_rst: emmc-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10              0x400010b0
+		>;
+	};
+
+	pinctrl_enet_mdio: enet-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO            0x10b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC             0x10b0
+		>;
+	};
+
+	pinctrl_enet1_phy_int: enet1-phy-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07           0x10b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00     0x100b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01     0x100b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN          0x100b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1      0x400000b1
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00     0xb0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01     0xb0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN          0xb0
+		>;
+	};
+
+	pinctrl_ext_uart: ext-uartgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_DATA0__UART7_DCE_RX      0xb0
+			MX6UL_PAD_ENET2_RX_EN__UART7_DCE_TX         0xb0
+		>;
+	};
+
+	pinctrl_fan_enable: fan-enablegrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05            0x400000b0
+		>;
+	};
+
+	pinctrl_gpio_motor: gpio-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07            0x400000b0
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08            0x400000b0
+			MX6UL_PAD_LCD_DATA04__GPIO3_IO09            0x400000b0
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19           0xb0
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25         0xb0
+		>;
+	};
+
+	pinctrl_hog_pins: hog-pinsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA07__GPIO3_IO12            0x400000b0
+			MX6UL_PAD_LCD_DATA08__GPIO3_IO13            0x400000b0
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13              0x400070a0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10            0x400000b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11            0x400000b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA           0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL           0x400008b0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21         0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20         0x400008b0
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__USDHC2_VSELECT        0x70b1
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19             0xb0
+		>;
+	};
+
+	pinctrl_pwm_cp: pinctrl-pwm-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT             0x60a0
+		>;
+	};
+
+	pinctrl_pwm_digital_input_ref: pwm-digital-input-refgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT              0xb0
+		>;
+	};
+
+	pinctrl_pwm_fan: pwm-fangrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT                0x60a0
+		>;
+	};
+
+	pinctrl_qca700x_cp_btld: qca700x-cp-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA13__GPIO3_IO18            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_int: qca700x-cp-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_DATA1__GPIO2_IO19             0x10b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_rst: qca700x-cp-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_mains_btld: qca700x-mains-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA11__GPIO3_IO16            0x400000b0
+		>;
+	};
+
+	pinctrl_rotary_switch1: rotary-switch1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22           0xb0
+			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23           0xb0
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24         0xb0
+		>;
+	};
+
+	pinctrl_rotary_switch2: rotary-switch2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18            0xb0
+			MX6UL_PAD_LCD_DATA23__GPIO3_IO28            0xb0
+			MX6UL_PAD_LCD_DATA22__GPIO3_IO27            0xb0
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26            0xb0
+		>;
+	};
+
+	pinctrl_rs485_1: rs485-1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18           0xb0
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX       0xb0
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX       0xb0
+		>;
+	};
+
+	pinctrl_rs485_2: rs485-2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24            0x10b0
+			MX6UL_PAD_CSI_DATA01__UART5_DCE_RX          0x10b0
+			MX6UL_PAD_CSI_DATA00__UART5_DCE_TX          0x10b0
+		>;
+	};
+
+	pinctrl_status_leds: status-ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA09__GPIO3_IO14            0xb0
+			MX6UL_PAD_LCD_DATA10__GPIO3_IO15            0xb0
+			MX6UL_PAD_LCD_DATA14__GPIO3_IO19            0xb0
+		>;
+	};
+
+	pinctrl_stm32: stm32grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA1__UART6_DCE_RX      0x10b0
+			MX6UL_PAD_ENET2_RX_DATA0__UART6_DCE_TX      0x10b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DTE_RX             0xb0
+			MX6UL_PAD_LCD_ENABLE__UART4_DTE_TX          0xb0
+		>;
+	};
+
+	pinctrl_usb: usbgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USB_OTG1_OC              0x70b0
+			MX6UL_PAD_SD1_DATA0__ANATOP_OTG1_ID         0x70b0
+		>;
+	};
+
+	pinctrl_usb_pwr: usb-pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USB_OTG1_PWR             0xb0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x7071
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x7071
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x7071
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x7071
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x7071
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x7071
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x7071
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x7071
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x7071
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x7071
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70b1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70b1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70b1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70b1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70b1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70b1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70b1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70b1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70b1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70b1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70f1
+		>;
+	};
+
+	pinctrl_wdog2: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_VSYNC__WDOG2_WDOG_B           0x10b0
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default_snvs";
+	pinctrl-0 = <&pinctrl_cp_peak_snvs
+		     &pinctrl_gpio_motor_snvs
+		     &pinctrl_relay_sense_snvs
+		     &pinctrl_rotary_switch1_snvs>;
+
+	pinctrl_accelerometer_int1_snvs: accelerometer-int1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05         0x130a0
+		>;
+	};
+
+	pinctrl_cp_peak_snvs: cp-peak-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10           0x130a0
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11           0x130a0
+		>;
+	};
+
+	pinctrl_enet1_phy_rst: enet1-phy-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06         0x100a0
+		>;
+	};
+
+	pinctrl_fan_sense_snvs: fan-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01         0x100a0
+		>;
+	};
+
+	pinctrl_gpio_motor_snvs: gpio-motor-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08         0x110a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_int: qca700x-mains-intgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09         0x130a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_rst: qca700x-mains-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07         0x400100a0
+		>;
+	};
+
+	pinctrl_relay_sense_snvs: relay-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03         0x100a0
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02         0x100a0
+		>;
+	};
+
+	pinctrl_rotary_switch1_snvs: rotary-switch1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00         0x110a0
+		>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_digital_input_ref>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_cp>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	fsl,dte-mode;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_2>;
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_stm32>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ext_uart>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb
+		     &pinctrl_usb_pwr>;
+	dr_mode = "host";
+	power-active-high;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usbphy2 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&sw2_reg>;
+	vqmmc-supply = <&reg_1v8>;
+	mmc-pwrseq = <&emmc_pwrseq>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog2>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-master.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-master.dts
new file mode 100644
index 000000000000..67007ce383e3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-master.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Master";
+	compatible = "chargebyte,imx6ull-tarragon-master", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&ecspi4 {
+	status = "okay";
+
+	qca700x_mains: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_mains_int
+			     &pinctrl_qca700x_mains_rst
+			     &pinctrl_qca700x_mains_btld>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-micro.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-micro.dts
new file mode 100644
index 000000000000..e471c2005bee
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-micro.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Micro";
+	compatible = "chargebyte,imx6ull-tarragon-micro", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slave.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slave.dts
new file mode 100644
index 000000000000..cee223b5f8e1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slave.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Slave";
+	compatible = "chargebyte,imx6ull-tarragon-slave", "fsl,imx6ull";
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slavext.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slavext.dts
new file mode 100644
index 000000000000..7fd53b7a4372
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slavext.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon SlaveXT";
+	compatible = "chargebyte,imx6ull-tarragon-slavext", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dts
new file mode 100644
index 000000000000..e593b7036fc7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULL2 SoM on MBa6ULx board";
+	compatible = "tq,imx6ull-tqma6ull2-mba6ulx", "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2.dtsi
new file mode 100644
index 000000000000..8541cb3f3b3e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULL2 SoM";
+	compatible = "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+	/* Errata ERR010450 Workaround */
+	max-frequency = <99000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017031
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017039
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017039
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017039
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017039
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017039
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017039
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017039
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017039
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017039
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l-mba6ulx.dts
new file mode 100644
index 000000000000..33437aae9822
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6ULL2L SoM on MBa6ULx board";
+	compatible = "tq,imx6ull-tqma6ull2l-mba6ulx", "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l.dtsi
new file mode 100644
index 000000000000..be593d47e3b1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6ULL2L SoM";
+	compatible = "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+	/* Errata ERR010450 Workaround */
+	max-frequency = <99000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017031
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017039
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017039
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017039
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017039
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017039
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017039
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017039
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017039
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017039
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
index b7e67d121322..2bccd45e9fc2 100644
--- a/arch/arm/boot/dts/imx6ull.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
@@ -50,8 +50,8 @@
 };
 
 / {
-	soc {
-		aips3: aips-bus@2200000 {
+	soc: soc {
+		aips3: bus@2200000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -68,6 +68,13 @@
 				clock-names = "dcp";
 			};
 
+			rngb: rng@2284000 {
+				compatible = "fsl,imx6ull-rngb", "fsl,imx25-rngb";
+				reg = <0x02284000 0x4000>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_DUMMY>;
+			};
+
 			iomuxc_snvs: iomuxc-snvs@2290000 {
 				compatible = "fsl,imx6ull-iomuxc-snvs";
 				reg = <0x02290000 0x4000>;
diff --git a/arch/arm/boot/dts/imx6ulz-14x14-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6ulz-14x14-evk.dts
index 483d9732c002..483d9732c002 100644
--- a/arch/arm/boot/dts/imx6ulz-14x14-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ulz-14x14-evk.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
new file mode 100644
index 000000000000..c92e4e2f6ab9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 BSH Hausgeraete GmbH
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx6ulz.dtsi"
+
+/ {
+	model = "BSH SMM M2";
+	compatible = "bsh,imx6ulz-bsh-smm-m2", "fsl,imx6ull", "fsl,imx6ulz";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	usdhc2_pwrseq: usdhc2-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "peripheral";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usdhc2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wlan>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	cap-sdio-irq;
+	mmc-pwrseq = <&usdhc2_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&gpio1>;
+		interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&wdog1 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpmi_nand: gpmi-nand {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0xb0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0xb0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0xb0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0xb000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0xb0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0xb0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0xb0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0xb0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0xb0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0xb0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0xb0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0xb0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0xb0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0xb0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b099
+			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
+			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b099
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x79		/* BT_REG_ON */
+			MX6UL_PAD_SD1_CLK__GPIO2_IO17		0x100b1		/* BT_DEV_WAKE out */
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x1b0b0		/* BT_HOST_WAKE in */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17059
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x10059
+			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_SD1_DATA3__GPIO2_IO21		0x79		/* WL_REG_ON */
+			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22	0x100b1		/* WL_DEV_WAKE - WiFi_GPIO_4 - WiFi FW UART */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x1b0b1		/* WL_HOST_WAKE - WIFI_GPIO_0 - OOB IRQ */
+			MX6UL_PAD_ENET1_RX_EN__OSC32K_32K_OUT	0x4001b031	/* OSC 32Khz wifi clk in */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ulz.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ulz.dtsi
index 0b5f1a763567..0b5f1a763567 100644
--- a/arch/arm/boot/dts/imx6ulz.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ulz.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-aster.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-aster.dtsi
new file mode 100644
index 000000000000..01612741f792
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-aster.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	cs-gpios = <
+		&gpio4 11 GPIO_ACTIVE_LOW /* SODIMM 86 / regular SSPFRM as UNO_SPI_CS or  */
+		&gpio4 23 GPIO_ACTIVE_LOW /* SODIMM 65 / already muxed pinctrl_gpio2 as SPI_CE0_N */
+		&gpio4 22 GPIO_ACTIVE_LOW /* SODIMM 85 / already muxed pinctrl_gpio2 as SPI_CE1_N */
+	>;
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-eval-v3.dtsi
new file mode 100644
index 000000000000..326440f2b4f4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-eval-v3.dtsi
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+/ {
+	/* Fixed crystal dedicated to MCP2515. */
+	clk16m: clk16m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <16000000>;
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+	status = "disabled";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+
+	mcp2515: can@0 {
+		clocks = <&clk16m>;
+		compatible = "microchip,mcp2515";
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_int>;
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		vdd-supply = <&reg_3v3>;
+		xceiver-supply = <&reg_5v0>;
+	};
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris-v2.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..b687727f956a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris-v2.dtsi
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* SODIMM 100 */
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart_b_c_on_x14_enable turns the UART transceiver for UART2 and 5 on. If one wants to
+	 * turn the transceiver off, that property has to be deleted and the gpio handled in
+	 * userspace.
+	 * The same applies to uart_a_on_x13_enable where the UART_A transceiver is turned on.
+	 */
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD, UHS-I capable uSD slot */
+&usdhc1 {
+	cap-power-off-card;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris.dtsi
new file mode 100644
index 000000000000..6a9e5ab59691
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris.dtsi
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart25 turns the UART transceiver for UART2 and 5 on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled in userspace.
+	 * The same applies to uart1_tx_on where the UART1 transceiver is turned on.
+	 */
+	uart25-tx-on-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart1-tx-on-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri.dtsi
new file mode 100644
index 000000000000..9fe51884af79
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri.dtsi
@@ -0,0 +1,1142 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		compatible = "pwm-backlight";
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_bl_on>;
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	extcon_usbc_det: usbc-det {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbc_det>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		backlight = <&backlight>;
+		compatible = "edt,et057090dhu";
+		power-supply = <&reg_3v3>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V";
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "5V";
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3";
+	};
+
+	reg_module_3v3_avdd: regulator-module-3v3-avdd {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_AVDD_AUDIO";
+	};
+
+	reg_module_3v3_eth: regulator-module-3v3-eth {
+		compatible = "regulator-fixed";
+		off-on-delay-us = <200000>;
+		regulator-name = "+V3.3_ETH";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_LDO1>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>; /* SODIMM 129 / USBH_PEN */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "VCC_USB[1-4]";
+		vin-supply = <&reg_5v0>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx7-sgtl5000";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai1>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
+			sound-dai = <&codec>;
+		};
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	vref-supply = <&reg_DCDC3>;
+};
+
+/* ADC2 is not available as it conflicts with AD7879 resistive touchscreen. */
+
+&cpu0 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* SODIMM 86 / SSPFRM */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+	clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+		 <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+		 <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+		 <&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
+	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_module_3v3_eth>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet1>;
+	pinctrl-1 = <&pinctrl_enet1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Micrel KSZ8041RNL */
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			micrel,led-mode = <0>;
+			reg = <0>;
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_135",
+			  "SODIMM_22",
+			  "",
+			  "",
+			  "SODIMM_37",
+			  "SODIMM_29",
+			  "SODIMM_59",
+			  "SODIMM_28",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "",
+			  "",
+			  "SODIMM_188",
+			  "SODIMM_178";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_111",
+			  "SODIMM_113",
+			  "SODIMM_115",
+			  "SODIMM_117",
+			  "SODIMM_119",
+			  "SODIMM_121",
+			  "SODIMM_123",
+			  "SODIMM_125",
+			  "SODIMM_91",
+			  "SODIMM_89",
+			  "SODIMM_105",
+			  "SODIMM_152",
+			  "SODIMM_150",
+			  "SODIMM_95",
+			  "SODIMM_126",
+			  "SODIMM_107",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_118",
+			  "SODIMM_120",
+			  "SODIMM_122",
+			  "SODIMM_124",
+			  "SODIMM_127",
+			  "SODIMM_130",
+			  "SODIMM_132",
+			  "SODIMM_134",
+			  "SODIMM_133",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_110",
+			  "SODIMM_112",
+			  "SODIMM_128";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "SODIMM_93",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_136",
+			  "SODIMM_138",
+			  "SODIMM_140",
+			  "SODIMM_142",
+			  "SODIMM_144",
+			  "SODIMM_146";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_35",
+			  "SODIMM_33",
+			  "SODIMM_38",
+			  "SODIMM_36",
+			  "SODIMM_21",
+			  "SODIMM_19",
+			  "SODIMM_131",
+			  "SODIMM_129",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_81",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_75",
+			  "SODIMM_101",
+			  "SODIMM_103",
+			  "SODIMM_79",
+			  "SODIMM_97",
+			  "SODIMM_67",
+			  "SODIMM_59",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_69",
+			  "SODIMM_71",
+			  "SODIMM_73",
+			  "SODIMM_47",
+			  "SODIMM_190",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53",
+			  "",
+			  "",
+			  "SODIMM_98",
+			  "SODIMM_184",
+			  "SODIMM_186",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_100",
+			  "SODIMM_102";
+};
+
+&gpio6 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_169",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_77",
+			  "SODIMM_24",
+			  "",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_32",
+			  "SODIMM_34";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "SODIMM_63",
+			  "SODIMM_55",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_196",
+			  "SODIMM_194",
+			  "",
+			  "SODIMM_99",
+			  "",
+			  "",
+			  "SODIMM_137";
+};
+
+/* NAND on such SKUs */
+&gpmi {
+	fsl,use-minimum-ecc;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+};
+
+/* On-module Power I2C */
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1 &pinctrl_i2c1_int>;
+	pinctrl-1 = <&pinctrl_i2c1_recovery &pinctrl_i2c1_int>;
+	scl-gpios = <&gpio1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
+		compatible = "fsl,sgtl5000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sai1_mclk>;
+		reg = <0xa>;
+		VDDA-supply = <&reg_module_3v3_avdd>;
+		VDDD-supply = <&reg_DCDC3>;
+		VDDIO-supply = <&reg_module_3v3>;
+	};
+
+	ad7879_ts: touchscreen@2c {
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,resistance-plate-x = <120>;
+		compatible = "adi,ad7879-1";
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x2c>;
+		touchscreen-max-pressure = <4096>;
+		status = "disabled";
+	};
+
+	pmic@33 {
+		compatible = "ricoh,rn5t567";
+		reg = <0x33>;
+
+		regulators {
+			reg_DCDC1: DCDC1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1000000>;
+				regulator-name = "+V1.0_SOC";
+			};
+
+			reg_DCDC2: DCDC2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <975000>;
+				regulator-name = "+V1.1_ARM";
+			};
+
+			reg_DCDC3: DCDC3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8";
+			};
+
+			reg_DCDC4: DCDC4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1350000>;
+				regulator-min-microvolt = <1350000>;
+				regulator-name = "+V1.35_DRAM";
+			};
+
+			reg_LDO1: LDO1 {
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3_ETH";
+			};
+
+			reg_LDO2: LDO2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_SD";
+			};
+
+			reg_LDO3: LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3_LPSR";
+			};
+
+			reg_LDO4: LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_LPSR";
+			};
+
+			reg_LDO5: LDO5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3";
+			};
+		};
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_recovery>;
+	scl-gpios = <&gpio7 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio7 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;        /* SODIMM 107 / INT */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_connector>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;      /* SODIMM 106 / RST */
+		status = "disabled";
+	};
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+		status = "disabled";
+	};
+};
+
+&lcdif {
+	assigned-clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_VIDEO_POST_DIV>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+	status = "disabled";
+
+	port {
+		lcdif_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+};
+
+&reg_1p0d {
+	vin-supply = <&reg_DCDC3>; /* VDDA_1P8_IN */
+};
+
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
+	uart-has-rtscts;
+};
+
+/* Colibri UART_B */
+&uart2 {
+	assigned-clocks = <&clks IMX7D_UART2_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+};
+
+/* Colibri UART_C */
+&uart3 {
+	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	dr_mode = "otg";
+	extcon = <0>, <&extcon_usbc_det>;
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_cd_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_cd_usdhc1>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_cd_usdhc1_sleep>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_LDO2>;
+	wakeup-source;
+};
+
+/* eMMC on 1GB (eMMC) SKUs */
+&usdhc3 {
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	fsl,tuning-step = <2>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	sdhci-caps-mask = <0x80000000 0x0>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&reg_DCDC3>;
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4>;
+
+	/*
+	 * Atmel MXT touchsceen + Capacitive Touch Adapter
+	 * NOTE: This pin group conflicts with pin groups pinctrl_pwm2/pinctrl_pwm3.
+	 * Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adapter: atmeladaptergrp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74 /* SODIMM 28 / INT */
+			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14 /* SODIMM 30 / RST */
+		>;
+	};
+
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	pinctrl_atmel_connector: atmelconnectorgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x14 /* SODIMM 106 / RST */
+			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x74 /* SODIMM 107 / INT */
+		>;
+	};
+
+	pinctrl_can_int: canintgrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SCL__ECSPI3_MISO		0x2 /* SODIMM 90 */
+			MX7D_PAD_I2C1_SDA__ECSPI3_MOSI		0x2 /* SODIMM 92 */
+			MX7D_PAD_I2C2_SCL__ECSPI3_SCLK		0x2 /* SODIMM 88 */
+		>;
+	};
+
+	pinctrl_ecspi3_cs: ecspi3csgrp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x14 /* SODIMM 86 */
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x73
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x73
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER		0x73
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x73
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x73
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x73
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x73
+			MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1		0x73
+			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x3
+			MX7D_PAD_SD2_WP__ENET1_MDC			0x3
+		>;
+	};
+
+	pinctrl_enet1_sleep: enet1-sleepgrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0		0x0
+			MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1		0x0
+			MX7D_PAD_ENET1_RGMII_RXC__GPIO7_IO5		0x0
+			MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4		0x0
+			MX7D_PAD_ENET1_RGMII_TD0__GPIO7_IO6		0x0
+			MX7D_PAD_ENET1_RGMII_TD1__GPIO7_IO7		0x0
+			MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10		0x0
+			MX7D_PAD_GPIO1_IO12__GPIO1_IO12			0x0
+			MX7D_PAD_SD2_CD_B__GPIO5_IO9			0x0
+			MX7D_PAD_SD2_WP__GPIO5_IO10			0x0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX	0x79 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX	0x79 /* SODIMM 55 */
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x79 /* SODIMM 188 */
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x79 /* SODIMM 178 */
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x14 /* SODIMM 110 */
+			MX7D_PAD_EPDC_DATA00__GPIO2_IO0		0x14 /* SODIMM 111 */
+			MX7D_PAD_EPDC_DATA01__GPIO2_IO1		0x14 /* SODIMM 113 */
+			MX7D_PAD_EPDC_DATA02__GPIO2_IO2		0x14 /* SODIMM 115 */
+			MX7D_PAD_EPDC_DATA03__GPIO2_IO3		0x14 /* SODIMM 117 */
+			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x14 /* SODIMM 119 */
+			MX7D_PAD_EPDC_DATA05__GPIO2_IO5		0x14 /* SODIMM 121 */
+			MX7D_PAD_EPDC_DATA06__GPIO2_IO6		0x14 /* SODIMM 123 */
+			MX7D_PAD_EPDC_DATA07__GPIO2_IO7		0x14 /* SODIMM 125 */
+			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
+			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
+			MX7D_PAD_EPDC_DATA10__GPIO2_IO10	0x74 /* SODIMM 105 */
+			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x14 /* SODIMM 152 */
+			MX7D_PAD_EPDC_DATA12__GPIO2_IO12	0x14 /* SODIMM 150 */
+			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x14 /* SODIMM 126 */
+			MX7D_PAD_EPDC_GDCLK__GPIO2_IO24		0x14 /* SODIMM 132 */
+			MX7D_PAD_EPDC_GDOE__GPIO2_IO25		0x14 /* SODIMM 134 */
+			MX7D_PAD_EPDC_GDRL__GPIO2_IO26		0x14 /* SODIMM 133 */
+			MX7D_PAD_EPDC_GDSP__GPIO2_IO27		0x14 /* SODIMM 104 */
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x14 /* SODIMM 112 */
+			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x14 /* SODIMM 128 */
+			MX7D_PAD_EPDC_SDCE0__GPIO2_IO20		0x14 /* SODIMM 122 */
+			MX7D_PAD_EPDC_SDCE1__GPIO2_IO21		0x14 /* SODIMM 124 */
+			MX7D_PAD_EPDC_SDCE2__GPIO2_IO22		0x14 /* SODIMM 127 */
+			MX7D_PAD_EPDC_SDCE3__GPIO2_IO23		0x14 /* SODIMM 130 */
+			MX7D_PAD_EPDC_SDCLK__GPIO2_IO16		0x14 /* SODIMM 114 */
+			MX7D_PAD_EPDC_SDLE__GPIO2_IO17		0x14 /* SODIMM 116 */
+			MX7D_PAD_EPDC_SDOE__GPIO2_IO18		0x14 /* SODIMM 118 */
+			MX7D_PAD_EPDC_SDSHR__GPIO2_IO19		0x14 /* SODIMM 120 */
+			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14 /* SODIMM 93 */
+			MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17	0x14 /* SODIMM 24 */
+			MX7D_PAD_SAI1_RX_DATA__GPIO6_IO12	0x14 /* SODIMM 169 */
+			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
+			MX7D_PAD_SD2_CLK__GPIO5_IO12		0x14 /* SODIMM 184 */
+			MX7D_PAD_SD2_CMD__GPIO5_IO13		0x14 /* SODIMM 186 */
+			MX7D_PAD_SD2_DATA2__GPIO5_IO16		0x14 /* SODIMM 100 */
+			MX7D_PAD_SD2_DATA3__GPIO5_IO17		0x14 /* SODIMM 102 */
+			MX7D_PAD_UART3_RTS_B__GPIO4_IO6		0x14 /* SODIMM 131 */
+		>;
+	};
+
+	pinctrl_gpio2: gpio2grp { /* On X22 Camera interface */
+		fsl,pins = <
+			MX7D_PAD_ECSPI1_MISO__GPIO4_IO18	0x14 /* SODIMM 79 */
+			MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17	0x14 /* SODIMM 103 */
+			MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16	0x14 /* SODIMM 101 */
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19		0x14 /* SODIMM 97 */
+			MX7D_PAD_ECSPI2_MISO__GPIO4_IO22	0x14 /* SODIMM 85 */
+			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x14 /* SODIMM 65 */
+			MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x14 /* SODIMM 81 */
+			MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x14 /* SODIMM 94 */
+			MX7D_PAD_I2C4_SCL__GPIO4_IO14		0x14 /* SODIMM 96 */
+			MX7D_PAD_I2C4_SDA__GPIO4_IO15		0x14 /* SODIMM 75 */
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x74 /* SODIMM 69 */
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14 /* SODIMM 98 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp { /* LCD 18-23 */
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA18__GPIO3_IO23		0x14 /* SODIMM 136 */
+			MX7D_PAD_LCD_DATA19__GPIO3_IO24		0x14 /* SODIMM 138 */
+			MX7D_PAD_LCD_DATA20__GPIO3_IO25		0x14 /* SODIMM 140 */
+			MX7D_PAD_LCD_DATA21__GPIO3_IO26		0x14 /* SODIMM 142 */
+			MX7D_PAD_LCD_DATA22__GPIO3_IO27		0x74 /* SODIMM 144 */
+			MX7D_PAD_LCD_DATA23__GPIO3_IO28		0x74 /* SODIMM 146 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp { /* Alternatively CAN2 */
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x14 /* SODIMM 188 */
+			MX7D_PAD_GPIO1_IO15__GPIO1_IO15		0x14 /* SODIMM 178 */
+		>;
+	};
+
+	pinctrl_gpio7: gpio7grp { /* Alternatively CAN1 */
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x14 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x14 /* SODIMM 55 */
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpioblongrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_WP__GPIO5_IO1		0x14 /* SODIMM 71 */
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	0x71
+			MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	0x74
+			MX7D_PAD_SD3_CLK__NAND_CLE		0x71
+			MX7D_PAD_SD3_CMD__NAND_ALE		0x71
+			MX7D_PAD_SD3_DATA0__NAND_DATA00		0x71
+			MX7D_PAD_SD3_DATA1__NAND_DATA01		0x71
+			MX7D_PAD_SD3_DATA2__NAND_DATA02		0x71
+			MX7D_PAD_SD3_DATA3__NAND_DATA03		0x71
+			MX7D_PAD_SD3_DATA4__NAND_DATA04		0x71
+			MX7D_PAD_SD3_DATA5__NAND_DATA05		0x71
+			MX7D_PAD_SD3_DATA6__NAND_DATA06		0x71
+			MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
+			MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+			MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
+		>;
+	};
+
+	pinctrl_i2c1_int: i2c1intgrp { /* PMIC / TOUCH */
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x79
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL	0x4000007f /* SODIMM 196 */
+			MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA	0x4000007f /* SODIMM 194 */
+		>;
+	};
+
+	pinctrl_i2c4_recovery: i2c4-recoverygrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_TD2__GPIO7_IO8	0x4000007f
+			MX7D_PAD_ENET1_RGMII_TD3__GPIO7_IO9	0x4000007f
+		>;
+	};
+
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79 /* SODIMM 76 */
+			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79 /* SODIMM 70 */
+			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79 /* SODIMM 60 */
+			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79 /* SODIMM 58 */
+			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79 /* SODIMM 78 */
+			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79 /* SODIMM 72 */
+			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79 /* SODIMM 80 */
+			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79 /* SODIMM 46 */
+			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79 /* SODIMM 62 */
+			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79 /* SODIMM 48 */
+			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79 /* SODIMM 74 */
+			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79 /* SODIMM 50 */
+			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79 /* SODIMM 52 */
+			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79 /* SODIMM 54 */
+			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79 /* SODIMM 66 */
+			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79 /* SODIMM 64 */
+			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79 /* SODIMM 57 */
+			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79 /* SODIMM 61 */
+		>;
+	};
+
+	pinctrl_lcdif_dat_24: lcdifdat24grp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79 /* SODIMM 136 */
+			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79 /* SODIMM 138 */
+			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79 /* SODIMM 140 */
+			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79 /* SODIMM 142 */
+			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79 /* SODIMM 144 */
+			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79 /* SODIMM 146 */
+		>;
+	};
+
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_CLK__LCD_CLK		0x79 /* SODIMM 56 */
+			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79 /* SODIMM 44 */
+			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79 /* SODIMM 68 */
+			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79 /* SODIMM 82 */
+		>;
+	};
+
+	pinctrl_lvds_transceiver: lvdstx {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2     0x14 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3     0x74 /* SODIMM 55 */
+			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11    0x14 /* SODIMM 99 */
+			MX7D_PAD_EPDC_DATA13__GPIO2_IO13        0x14 /* SODIMM 95 */
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x4  /* SODIMM 59 */
+			MX7D_PAD_GPIO1_IO08__PWM1_OUT		0x79 /* SODIMM 59 */
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO09__PWM2_OUT		0x79 /* SODIMM 28 */
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO10__PWM3_OUT		0x79 /* SODIMM 30 */
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20	0x4  /* SODIMM 67 */
+			MX7D_PAD_GPIO1_IO11__PWM4_OUT		0x79 /* SODIMM 67 */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS	0x79 /* SODIMM 25 */
+			MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS	0x79 /* SODIMM 27 */
+			MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX	0x79 /* SODIMM 35 */
+			MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX	0x79 /* SODIMM 33 */
+		>;
+	};
+
+	pinctrl_uart1_ctrl1: uart1ctrl1grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_DATA0__GPIO5_IO14		0x14 /* SODIMM 23 / DTR */
+			MX7D_PAD_SD2_DATA1__GPIO5_IO15		0x14 /* SODIMM 31 / DCD */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS	0x79 /* SODIMM 32 / CTS */
+			MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS	0x79 /* SODIMM 34 / RTS */
+			MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX	0x79 /* SODIMM 38 */
+			MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX	0x79 /* SODIMM 36 */
+		>;
+	};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX	0x79 /* SODIMM 21 */
+			MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX	0x79 /* SODIMM 19 */
+		>;
+	};
+
+	pinctrl_usbc_det: usbcdetgrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_CRS__GPIO7_IO14		0x14 /* SODIMM 137 / USBC_DET */
+		>;
+	};
+
+	pinctrl_usbh_reg: usbhreggrp {
+		fsl,pins = <
+			MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14 /* SODIMM 129 / USBH_PEN */
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19 /* SODIMM 47 */
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59 /* SODIMM 190 */
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59 /* SODIMM 192 */
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59 /* SODIMM 49 */
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59 /* SODIMM 51 */
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59 /* SODIMM 53 */
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
+		>;
+	};
+
+	/* Avoid backfeeding with removed card power. */
+	pinctrl_usdhc1_sleep: usdhc1-slpgrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x10
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x10
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x10
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x10
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x10
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x10
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
+			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x19
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5a
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5a
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5a
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5a
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5a
+			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1a
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5b
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5b
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5b
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5b
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5b
+			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1b
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
+			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
+			MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
+			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x1f
+		>;
+	};
+
+	pinctrl_sai1_mclk: sai1mclkgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
+		>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_lpsr>;
+
+	pinctrl_cd_usdhc1: cdusdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* SODIMM 43 / MMC_CD */
+		>;
+	};
+
+	pinctrl_cd_usdhc1_sleep: cdusdhc1-slpgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x0
+		>;
+	};
+
+	pinctrl_gpio_lpsr: gpiolpsrgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59 /* SODIMM 135 */
+			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59 /* SODIMM 22 */
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeysgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x19 /* SODIMM 45 / WAKE_UP */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL	0x4000007f
+			MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
+		>;
+	};
+
+	pinctrl_i2c1_recovery: i2c1-recoverygrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4	0x4000007f
+			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x4000007f
+		>;
+	};
+
+	pinctrl_uart1_ctrl2: uart1ctrl2grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14 /* SODIMM 37 / RI */
+			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x14 /* SODIMM 29 / DSR */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7-mba7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi
index 50abf18ad30b..3df6dff7734a 100644
--- a/arch/arm/boot/dts/imx7-mba7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0 OR X11
 /*
- * Device Tree Include file for TQ Systems MBa7 carrier board.
+ * Device Tree Include file for TQ-Systems MBa7 carrier board.
  *
- * Copyright (C) 2016 TQ Systems GmbH
+ * Copyright (C) 2016 TQ-Systems GmbH
  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
  * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
  *
@@ -14,6 +14,12 @@
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc1;
+		/delete-property/ mmc2;
+	};
+
 	beeper {
 		compatible = "gpio-beeper";
 		gpios = <&pca9555 0 GPIO_ACTIVE_HIGH>;
@@ -164,6 +170,20 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "imx-audio-tlv320aic32x4";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+		audio-routing =
+			"IN3_L", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"IN1_L", "Line In Jack",
+			"IN1_R", "Line In Jack",
+			"Line Out Jack", "LOL",
+			"Line Out Jack", "LOR";
+	};
 };
 
 &adc1 {
@@ -179,7 +199,6 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	num-chipselects = <3>;
 	cs-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>, <&gpio4 1 GPIO_ACTIVE_LOW>,
 		   <&gpio4 2 GPIO_ACTIVE_LOW>;
 	status = "okay";
@@ -188,7 +207,6 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
-	num-chipselects = <1>;
 	status = "okay";
 };
 
@@ -198,7 +216,6 @@
 	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>;
 	phy-reset-duration = <1>;
-	phy-reset-delay = <1>;
 	phy-supply = <&reg_fec1_pwdn>;
 	phy-handle = <&ethphy1_0>;
 	fsl,magic-packet;
@@ -214,10 +231,45 @@
 			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
 			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
 			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-			/* LED1: Link/Activity, LED2: Error */
-			ti,led-function = <0x0db0>;
-			/* Active low, LED1 and LED2 driven by phy */
-			ti,led-ctrl = <0x1001>;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		};
+	};
+};
+
+&flash0 {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		uboot@0 {
+			label = "U-Boot";
+			reg = <0x0 0xd0000>;
+		};
+
+		env1@d0000 {
+			label = "ENV1";
+			reg = <0xd0000 0x10000>;
+		};
+
+		env2@e0000 {
+			label = "ENV2";
+			reg = <0xe0000 0x10000>;
+		};
+
+		dtb@f0000 {
+			label = "DTB";
+			reg = <0xf0000 0x10000>;
+		};
+
+		linux@100000 {
+			label = "Linux";
+			reg = <0x100000 0x700000>;
+		};
+
+		rootfs@800000 {
+			label = "RootFS";
+			reg = <0x800000 0x3800000>;
 		};
 	};
 };
@@ -250,7 +302,7 @@
 	tlv320aic32x4: audio-codec@18 {
 		compatible = "ti,tlv320aic32x4";
 		reg = <0x18>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		ldoin-supply = <&reg_audio_3v3>;
 		iov-supply = <&reg_audio_3v3>;
@@ -362,13 +414,25 @@
 		>;
 	};
 
-
 	pinctrl_pca9555: pca95550grp {
 		fsl,pins = <
 			MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x78
 		>;
 	};
 
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_MCLK__SAI1_MCLK		0x11
+			MX7D_PAD_SAI1_RX_BCLK__SAI1_RX_BCLK	0x1c
+			MX7D_PAD_SAI1_RX_DATA__SAI1_RX_DATA0	0x1c
+			MX7D_PAD_SAI1_RX_SYNC__SAI2_RX_SYNC	0x1c
+
+			MX7D_PAD_SAI1_TX_BCLK__SAI1_TX_BCLK	0x1c
+			MX7D_PAD_SAI1_TX_DATA__SAI1_TX_DATA0	0x14
+			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x14
+		>;
+	};
+
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
 			MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x7e
@@ -472,6 +536,12 @@
 			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x59
 		>;
 	};
+
+	pinctrl_wdog1: wdog1grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B	0x30
+		>;
+	};
 };
 
 &pwm1 {
@@ -480,6 +550,16 @@
 	status = "okay";
 };
 
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&clks IMX7D_SAI1_ROOT_SRC>,
+			  <&clks IMX7D_SAI1_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
+	assigned-clock-rates = <0>, <36864000>;
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -518,6 +598,9 @@
 	assigned-clocks = <&clks IMX7D_UART7_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
 	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
 	status = "okay";
 };
 
@@ -532,7 +615,8 @@
 	srp-disable;
 	hnp-disable;
 	adp-disable;
-	dr_mode = "host";
+	over-current-active-low;
+	dr_mode = "otg";
 	status = "okay";
 };
 
@@ -548,3 +632,9 @@
 	no-1-8-v;
 	status = "okay";
 };
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+};
diff --git a/arch/arm/boot/dts/imx7-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
index 9aaed85138cb..3fc3130f9def 100644
--- a/arch/arm/boot/dts/imx7-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0 OR X11
 /*
- * Device Tree Include file for TQ Systems TQMa7x boards with full mounted PCB.
+ * Device Tree Include file for TQ-Systems TQMa7x boards with full mounted PCB.
  *
- * Copyright (C) 2016 TQ Systems GmbH
+ * Copyright (C) 2016 TQ-Systems GmbH
  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
  * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
  */
@@ -16,7 +16,17 @@
 };
 
 &cpu0 {
-	arm-supply = <&sw1a_reg>;
+	cpu-supply = <&sw1a_reg>;
+};
+
+&gpio2 {
+	/* Configured as pullup by QSPI pin group */
+	qspi-reset-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "qspi-reset";
+	};
 };
 
 &i2c1 {
@@ -118,11 +128,16 @@
 		};
 	};
 
-	/* NXP SE97BTP with temperature sensor + eeprom */
+	/* LM75A temperature sensor, TQMa7x 01xx */
+	lm75a: temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+	};
+
+	/* NXP SE97BTP with temperature sensor + eeprom, TQMa7x 02xx */
 	se97b: temperature-sensor-eeprom@1e {
 		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
 		reg = <0x1e>;
-		status = "okay";
 	};
 
 	/* ST M24C64 */
@@ -160,6 +175,25 @@
 		>;
 	};
 
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0	0x5A
+			MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1	0x5A
+			MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2	0x5A
+			MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3	0x5A
+			MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK	0x11
+			MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B	0x54
+			MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B	0x54
+		>;
+	};
+
+	pinctrl_qspi_reset: qspi_resetgrp {
+		fsl,pins = <
+			/* #QSPI_RESET */
+			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x52
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
@@ -217,6 +251,20 @@
 	};
 };
 
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi &pinctrl_qspi_reset>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <29000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+	};
+};
+
 &sdma {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-cl-som-imx7.dts
index 7646284e13a7..713483c39c9d 100644
--- a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-cl-som-imx7.dts
@@ -37,6 +37,10 @@
 	cpu-supply = <&sw1a_reg>;
 };
 
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
@@ -85,12 +89,12 @@
 
 	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
-		reg = <0x08>;
+		reg = <0x8>;
 
 		regulators {
 			sw1a_reg: sw1a {
 				regulator-min-microvolt = <700000>;
-				regulator-max-microvolt = <1475000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <6250>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-aster.dts
new file mode 100644
index 000000000000..00ab92e56da4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-aster.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Aster Carrier Board";
+	compatible = "toradex,colibri-imx7d-aster",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-aster.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-aster.dts
new file mode 100644
index 000000000000..212e0685585d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-aster.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ *
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB (eMMC) on Aster Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-aster",
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-eval-v3.dts
index 8ee73c870b12..1deece7e7129 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 /dts-v1/;
@@ -10,10 +10,12 @@
 / {
 	model = "Toradex Colibri iMX7D 1GB (eMMC) on Colibri Evaluation Board V3";
 	compatible = "toradex,colibri-imx7d-emmc-eval-v3",
-		     "toradex,colibri-imx7d-emmc", "fsl,imx7d";
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
 };
 
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
+	disable-over-current;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..22e7863c2e80
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris-v2.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris-v2",
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..a3cf8f50e3dc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris",
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc.dtsi
new file mode 100644
index 000000000000..9670f45eab3b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc.dtsi
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+#include "imx7d.dtsi"
+#include "imx7-colibri.dtsi"
+
+/ {
+	aliases {
+		/* Required to properly pass MAC addresses from bootloader. */
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC/SD slot */
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
+&gpio6 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_169",
+			  "SODIMM_157",
+			  "",
+			  "SODIMM_163",
+			  "SODIMM_77",
+			  "SODIMM_24",
+			  "",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_32",
+			  "SODIMM_34";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
+};
+
+/* eMMC */
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-eval-v3.dts
new file mode 100644
index 000000000000..33d787617db0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-eval-v3.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx7d-eval-v3",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris-v2.dts
new file mode 100644
index 000000000000..afdb1d06c7f6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris-v2.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris-v2",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris.dts
new file mode 100644
index 000000000000..531b0b99bd5a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-colibri.dtsi
new file mode 100644
index 000000000000..531a45b176a1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+#include "imx7d.dtsi"
+#include "imx7-colibri.dtsi"
+
+/ {
+	aliases {
+		/* Required to properly pass MAC addresses from bootloader. */
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
+/* NAND */
+&gpmi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator-mfg.dts b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator-mfg.dts
new file mode 100644
index 000000000000..a6d68165fb1e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator-mfg.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Kamstrup OMNIA Flex Concentrator in
+ * manufacturing/debugging mode.
+ *
+ * Copyright (C) 2020 Kamstrup A/S
+ * Author: Bruno Thomsen <bruno.thomsen@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx7d-flex-concentrator.dts"
+
+/ {
+	model = "Kamstrup OMNIA Flex Concentrator - Manufacturing";
+	compatible = "kam,imx7d-flex-concentrator-mfg", "fsl,imx7d";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+};
+
+&uart4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator.dts b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator.dts
new file mode 100644
index 000000000000..3a723843d562
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator.dts
@@ -0,0 +1,313 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Kamstrup OMNIA Flex Concentrator.
+ *
+ * Copyright (C) 2020 Kamstrup A/S
+ * Author: Bruno Thomsen <bruno.thomsen@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx7d-tqma7.dtsi"
+
+/* One I2C device on TQMa7 SoM is not mounted */
+/delete-node/ &ds1339;
+
+/ {
+	model = "Kamstrup OMNIA Flex Concentrator";
+	compatible = "kam,imx7d-flex-concentrator", "fsl,imx7d";
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 1024 MB - TQMa7D board configuration */
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "VBUS_USBOTG2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_vref_1v8: regulator-vref-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1V8_REF";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&sw2_reg>;
+	};
+
+	/*
+	 * Human Machine Interface consists of 4 dual red/green LEDs.
+	 * hmi-a:green is controlled directly by the switch-mode power supply.
+	 * hmi-a:red is not used.
+	 */
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "hmi-b:red:heartbeat-degraded";
+			gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			label = "hmi-b:green:heartbeat-running";
+			gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			label = "hmi-c:red:mesh-error";
+			gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			label = "hmi-c:green:mesh-activity";
+			gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "hmi-d:red:omnia-error";
+			gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			label = "hmi-d:green:omnia-activity";
+			gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	/*
+	 * Errata e10574 board restart workaround.
+	 */
+	gpio-restart {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_restart>;
+		compatible = "gpio-restart";
+		gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+/*
+ * Analog signals
+ * ADC1_IN0: SMPS - 5V output monitor (voltage divider: 1/0.2806)
+ */
+&adc1 {
+	vref-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	pcf2127: rtc@0 {
+		compatible = "nxp,pcf2127";
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+		reset-source;
+	};
+};
+
+&ecspi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	cs-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	/*
+	 * ST chip maximum SPI clock frequency is 33 MHz.
+	 *
+	 * TCG specification - Section 6.4.1 Clocking:
+	 * TPM shall support a SPI clock frequency range of 10-24 MHz.
+	 */
+	st33htph: tpm-tis@0 {
+		compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	/*
+	 * MDIO bus reset is used to generate PHY device reset before
+	 * Ethernet PHY type ID auto-detection. Otherwise this communication
+	 * fails as device does not answer when recommended reset circuit
+	 * is used.
+	 */
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-delay-us = <100000>;
+		reset-post-delay-us = <500000>;
+		reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>;
+
+		/* Microchip/Micrel KSZ8081RNB */
+		ethphy: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio1>;
+			interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+		};
+	};
+};
+
+/*
+ * Detection signals for internal USB modules.
+ * Used for robust USB plug and play handling such as USB downstream port
+ * power-cycle and USB hub reset in case of misbehaving or crashed modules.
+ *
+ * SMPS - AC input monitor based on zero crossing.
+ * Used for last gasp notification.
+ */
+&gpio3 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+	"", "", "", "", "smps-ac-monitor", "", "usb-hub-reset", "",
+	"", "", "", "", "", "", "", "",
+	"", "module-b-detection", "", "module-a-detection", "", "", "", "";
+};
+
+/*
+ * Tamper IRQ trigger timestamp reading.
+ * Used for sealed cover opened/closed notification.
+ */
+&gpio5 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+	"", "", "", "", "rtc-tamper-irq", "", "", "",
+	"", "", "", "", "", "", "", "",
+	"", "", "", "", "", "", "", "";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_misc>;
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO		0x7c /* X2-15 */
+			MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI		0x74 /* X2-18 */
+			MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK		0x74 /* X2-13 */
+			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23			0x74 /* X2-20 */
+			/* RTC - Tamper IRQ */
+			MX7D_PAD_SD2_CLK__GPIO5_IO12			0x3c /* X1-92 */
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX7D_PAD_LCD_CLK__ECSPI4_MISO			0x7c /* X2-72 */
+			MX7D_PAD_LCD_ENABLE__ECSPI4_MOSI		0x74 /* X2-68 */
+			MX7D_PAD_LCD_HSYNC__ECSPI4_SCLK			0x74 /* X2-76 */
+			MX7D_PAD_LCD_VSYNC__GPIO3_IO3			0x74 /* X2-78 */
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x03 /* X2-48 */
+			MX7D_PAD_GPIO1_IO11__ENET1_MDC			0x03 /* X2-46 */
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x71 /* X2-53 */
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x71 /* X2-55 */
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x71 /* X2-61 */
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x79 /* X2-56 */
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x79 /* X2-58 */
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x79 /* X2-64 */
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER		0x73 /* X2-52 */
+			/* PHY reset: SRE_FAST, DSE_X1 */
+			MX7D_PAD_ENET1_COL__GPIO7_IO15			0x00 /* X1-96 */
+			/* Clock from PHY to MAC: 100kPU */
+			MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1		0x70 /* X3-4 */
+			/* PHY interrupt: 100kPU, HYS */
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9			0x78 /* X1-80 */
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA01__GPIO3_IO6			0x14 /* X2-82 */
+			MX7D_PAD_EPDC_BDR0__GPIO2_IO28			0x14 /* X1-82 */
+			MX7D_PAD_EPDC_BDR1__GPIO2_IO29			0x14 /* X1-84 */
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30		0x14 /* X1-86 */
+			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31		0x14 /* X1-88 */
+			MX7D_PAD_UART2_TX_DATA__GPIO4_IO3		0x14 /* X1-90 */
+		>;
+	};
+
+	pinctrl_misc: miscgrp {
+		fsl,pins = <
+			/* Module A detection (low = present) */
+			MX7D_PAD_LCD_DATA22__GPIO3_IO27			0x7c /* X2-105 */
+			/* Module B detection (low = present) */
+			MX7D_PAD_LCD_DATA20__GPIO3_IO25			0x7c /* X2-103 */
+			/* SMPS - AC input monitor (high = failure) */
+			MX7D_PAD_LCD_DATA07__GPIO3_IO12			0x7c /* X2-88 */
+			/* USB - Hub reset */
+			MX7D_PAD_LCD_DATA09__GPIO3_IO14			0x74 /* X2-92 */
+		>;
+	};
+
+	pinctrl_restart: restartgrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x74 /* X1-94 */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX	0x7e /* X3-14 */
+			MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX	0x76 /* X3-16 */
+		>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC	0x5c /* X3-11 */
+			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x59 /* X3-9 */
+		>;
+	};
+
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	assigned-clocks = <&clks IMX7D_UART4_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	over-current-active-low;
+	dr_mode = "host";
+	status = "okay";
+};
+
+/*
+ * External watchdog feature provided by pcf2127.
+ */
+&wdog1 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx7d-mba7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts
index 221274c73dbd..32bf9fa9d00e 100644
--- a/arch/arm/boot/dts/imx7d-mba7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0 OR X11
 /*
- * Device Tree Source for TQ Systems TQMa7D board on MBa7 carrier board.
+ * Device Tree Source for TQ-Systems TQMa7D board on MBa7 carrier board.
  *
- * Copyright (C) 2016 TQ Systems GmbH
+ * Copyright (C) 2016 TQ-Systems GmbH
  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
  * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
  */
@@ -13,8 +13,8 @@
 #include "imx7-mba7.dtsi"
 
 / {
-	model = "TQ Systems TQMa7D board on MBa7 carrier board";
-	compatible = "tq,imx7d-mba7", "fsl,imx7d";
+	model = "TQ-Systems TQMa7D board on MBa7 carrier board";
+	compatible = "tq,imx7d-mba7", "tq,imx7d-tqma7", "fsl,imx7d";
 };
 
 &fec2 {
@@ -23,7 +23,6 @@
 	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 	phy-reset-duration = <1>;
-	phy-reset-delay = <1>;
 	phy-supply = <&reg_fec2_pwdn>;
 	phy-handle = <&ethphy2_0>;
 	fsl,magic-packet;
@@ -39,10 +38,7 @@
 			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
 			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
 			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-			/* LED1: Link/Activity, LED2: error */
-			ti,led-function = <0x0db0>;
-			/* active low, LED1/2 driven by phy */
-			ti,led-ctrl = <0x1001>;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
 		};
 	};
 };
@@ -102,8 +98,6 @@
 	/* probe deferral not supported */
 	/* pcie-bus-supply = <&reg_mpcie_1v5>; */
 	reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>;
-	disable-gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;
-	power-on-gpio = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx7d-meerkat96.dts b/arch/arm/boot/dts/nxp/imx/imx7d-meerkat96.dts
index 5339210b63d0..f0fda15f3020 100644
--- a/arch/arm/boot/dts/imx7d-meerkat96.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-meerkat96.dts
@@ -193,7 +193,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	keep-power-in-suspend;
-	tuning-step = <2>;
+	fsl,tuning-step = <2>;
 	vmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
 	broken-cd;
@@ -212,7 +212,7 @@
 	keep-power-in-suspend;
 	wakeup-source;
 	vmmc-supply = <&reg_wlreg_on>;
-	vqmmc-supply =<&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
 	status = "okay";
 
 	brcmf: wifi@1 {
diff --git a/arch/arm/boot/dts/imx7d-nitrogen7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-nitrogen7.dts
index 6b4acea1ef79..9c6476bda4a0 100644
--- a/arch/arm/boot/dts/imx7d-nitrogen7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-nitrogen7.dts
@@ -121,6 +121,10 @@
 	cpu-supply = <&sw1a_reg>;
 };
 
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
@@ -155,7 +159,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -284,7 +288,7 @@
 	codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		wlf,shared-lrclk;
 	};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-dwarf.dts
new file mode 100644
index 000000000000..12361fcbe24a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-dwarf.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright 2015 Technexion Ltd.
+//
+// Author: Wig Cheng  <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+/dts-v1/;
+
+#include "imx7d-pico.dtsi"
+/ {
+	model = "TechNexion PICO-IMX7D and DWARF baseboard";
+	compatible = "technexion,imx7d-pico-dwarf", "fsl,imx7d";
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx7d-sgtl5000";
+		audio-cpu = <&sai1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"LINE_IN", "Line In Jack",
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+	};
+
+	sys_mclk: clock-sys-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	sgtl5000: audio-codec@a {
+		reg = <0x0a>;
+		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
+		clocks = <&sys_mclk>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	pressure-sensor@60 {
+		compatible = "fsl,mpl3115";
+		reg = <0x60>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9554: io-expander@25 {
+		compatible = "nxp,pca9554";
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		reg = <0x25>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pca9554 4 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+	};
+};
+
+&iomuxc {
+	pinctrl_touchscreen: touchscreengrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x14
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7d-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-hobbit.dts
index 7b2198a9372c..6ad39dca7009 100644
--- a/arch/arm/boot/dts/imx7d-pico-hobbit.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-hobbit.dts
@@ -31,7 +31,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -41,7 +41,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_vref_1v8>;
 	};
@@ -64,7 +64,7 @@
 		interrupt-parent = <&gpio2>;
 		interrupts = <7 0>;
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio2 7 0>;
+		pendown-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_3p3v>;
 		ti,x-min = /bits/ 16 <0>;
 		ti,x-max = /bits/ 16 <4095>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-pico-nymph.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-nymph.dts
new file mode 100644
index 000000000000..af26284297a2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-nymph.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright 2015 Technexion Ltd.
+//
+// Author: Wig Cheng  <wig.cheng@technexion.com>
+//	   Richard Hu <richard.hu@technexion.com>
+//	   Tapani Utriainen <tapani@technexion.com>
+/dts-v1/;
+
+#include "imx7d-pico.dtsi"
+/ {
+	model = "TechNexion PICO-IMX7 and NYMPH baseboard";
+	compatible = "technexion,imx7d-pico-nymph", "fsl,imx7d";
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led {
+			label = "gpio-led";
+			gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx7d-sgtl5000";
+		audio-cpu = <&sai1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"LINE_IN", "Line In Jack",
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+	};
+
+	sys_mclk: clock-sys-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	sgtl5000: audio-codec@a {
+		reg = <0x0a>;
+		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
+		clocks = <&sys_mclk>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	adc@52 {
+		compatible = "ti,adc081c";
+		reg = <0x52>;
+		vref-supply = <&reg_2p5v>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	rtc@68 {
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x14
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7d-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-pi.dts
index 70bea95c06d8..62221131336f 100644
--- a/arch/arm/boot/dts/imx7d-pico-pi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-pi.dts
@@ -31,7 +31,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -41,7 +41,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_vref_1v8>;
 	};
@@ -61,6 +61,10 @@
 	};
 };
 
+&usdhc1 {
+	status = "disabled";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
diff --git a/arch/arm/boot/dts/imx7d-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-pico.dtsi
index 6f50ebf31a0a..8d5037ac03c7 100644
--- a/arch/arm/boot/dts/imx7d-pico.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico.dtsi
@@ -7,12 +7,42 @@
 #include "imx7d.dtsi"
 
 / {
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 50000 0>;
+		brightness-levels = <0 36 72 108 144 180 216 255>;
+		default-brightness-level = <6>;
+	};
+
 	/* Will be filled by the bootloader */
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0>;
 	};
 
+	panel {
+		compatible = "vxt,vl050-8048nt-c01";
+		backlight = <&backlight>;
+		power-supply = <&reg_lcd_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_lcdreg_on>;
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_wlreg_on: regulator-wlreg_on {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -78,6 +108,14 @@
 	assigned-clock-rates = <0>, <32768>;
 };
 
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &ecspi3 {
 	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -140,7 +178,7 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -230,6 +268,18 @@
 	};
 };
 
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
 &sai1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai1>;
@@ -260,6 +310,8 @@
 };
 
 &pwm4 { /* Backlight */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
 };
 
@@ -307,7 +359,7 @@
 	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
-	tuning-step = <2>;
+	fsl,tuning-step = <2>;
 	vmmc-supply = <&reg_3p3v>;
 	wakeup-source;
 	no-1-8-v;
@@ -388,7 +440,7 @@
 			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
 			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
 			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
-			MX7D_PAD_SD3_RESET_B__GPIO6_IO11                0x1  /* Ethernet reset */
+			MX7D_PAD_SD3_RESET_B__GPIO6_IO11		0x1  /* Ethernet reset */
 		>;
 	};
 
@@ -413,21 +465,61 @@
 		>;
 	};
 
+	pinctrl_lcdif: lcdifgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79
+			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79
+			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79
+			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79
+			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79
+			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79
+			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79
+			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79
+			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79
+			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79
+			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79
+			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79
+			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79
+			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79
+			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79
+			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79
+			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79
+			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79
+			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79
+			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79
+			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79
+			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79
+			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79
+			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79
+			MX7D_PAD_LCD_CLK__LCD_CLK		0x79
+			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x78
+			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x78
+			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x78
+			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14
+		>;
+	};
+
 	pinctrl_pwm1: pwm1 {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO08__PWM1_OUT   0x7f
+			MX7D_PAD_GPIO1_IO08__PWM1_OUT	0x7f
 		>;
 	};
 
 	pinctrl_pwm2: pwm2 {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__PWM2_OUT   0x7f
+			MX7D_PAD_GPIO1_IO09__PWM2_OUT	0x7f
 		>;
 	};
 
 	pinctrl_pwm3: pwm3 {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__PWM3_OUT   0x7f
+			MX7D_PAD_GPIO1_IO10__PWM3_OUT	0x7f
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO11__PWM4_OUT	0x7f
 		>;
 	};
 
@@ -577,6 +669,12 @@
 		>;
 	};
 
+	pinctrl_reg_lcdreg_on: reglcdongrp {
+	fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x59
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B	0x74
diff --git a/arch/arm/boot/dts/imx7d-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx7d-pinfunc.h
index 08ca1608fdb1..69f2c1ec8254 100644
--- a/arch/arm/boot/dts/imx7d-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pinfunc.h
@@ -592,7 +592,7 @@
 #define MX7D_PAD_UART2_RX_DATA__ECSPI1_SS3                        0x0130 0x03A0 0x0000 0x3 0x0
 #define MX7D_PAD_UART2_RX_DATA__ENET2_1588_EVENT1_IN              0x0130 0x03A0 0x0000 0x4 0x0
 #define MX7D_PAD_UART2_RX_DATA__GPIO4_IO2                         0x0130 0x03A0 0x0000 0x5 0x0
-#define MX7D_PAD_UART2_RX_DATA__ENET2_MDIO                        0x0130 0x03A0 0x0000 0x6 0x0
+#define MX7D_PAD_UART2_RX_DATA__ENET2_MDIO                        0x0130 0x03A0 0x0574 0x6 0x1
 #define MX7D_PAD_UART2_TX_DATA__UART2_DCE_TX                      0x0134 0x03A4 0x0000 0x0 0x0
 #define MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX                      0x0134 0x03A4 0x06FC 0x0 0x3
 #define MX7D_PAD_UART2_TX_DATA__I2C2_SDA                          0x0134 0x03A4 0x05E0 0x1 0x0
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-remarkable2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-remarkable2.dts
new file mode 100644
index 000000000000..92cb45dacda6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-remarkable2.dts
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ * Copyright (C) 2019 reMarkable AS - http://www.remarkable.com/
+ *
+ */
+
+/dts-v1/;
+
+#include "imx7d.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	model = "reMarkable 2.0";
+	compatible = "remarkable,imx7d-remarkable2", "fsl,imx7d";
+
+	chosen {
+		stdout-path = &uart6;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	thermal-zones {
+		epd-thermal {
+			thermal-sensors = <&sy7636a>;
+			polling-delay-passive = <30000>;
+			polling-delay = <30000>;
+
+			trips {
+				trip0 {
+					temperature = <49000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <50000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	reg_brcm: regulator-brcm {
+		compatible = "regulator-fixed";
+		regulator-name = "brcm_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_brcm_reg>;
+		gpio = <&gpio6 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <150>;
+	};
+
+	reg_digitizer: regulator-digitizer {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3_DIGITIZER";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pinctrl_digitizer_reg>;
+		pinctrl-1 = <&pinctrl_digitizer_reg>;
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100000>; /* 100 ms */
+	};
+
+	reg_touch: regulator-touch {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3_TOUCH";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_reg>;
+		gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi>;
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+		clocks = <&clks IMX7D_CLKO2_ROOT_DIV>;
+		clock-names = "ext_clock";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&buck1>;
+};
+
+&clks {
+	assigned-clocks = <&clks IMX7D_CLKO2_ROOT_SRC>,
+			  <&clks IMX7D_CLKO2_ROOT_DIV>;
+	assigned-clock-parents = <&clks IMX7D_CKIL>;
+	assigned-clock-rates = <0>, <32768>;
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	wacom_digitizer: digitizer@9 {
+		compatible = "hid-over-i2c";
+		reg = <0x09>;
+		hid-descr-addr = <0x01>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wacom>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		vdd-supply = <&reg_digitizer>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	bd71815: pmic@4b {
+		compatible = "rohm,bd71815";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bd71815>;
+		interrupt-parent = <&gpio6>; /* PMIC_INT_B GPIO6_IO16 */
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		gpio-controller;
+		clocks = <&clks IMX7D_CLKO2_ROOT_SRC>;
+		clock-output-names = "bd71815-32k-out";
+		#clock-cells = <0>;
+		#gpio-cells = <2>;
+
+		regulators {
+			buck1: buck1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2: buck2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3: buck3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <2700000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: buck4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: ldo1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: ldo2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: ldo3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: ldo4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: ldo5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6: ldodvref {
+				regulator-name = "ldodvref";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo7: ldolpsr {
+				regulator-name = "ldolpsr";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			boost: wled {
+				regulator-name = "wled";
+				regulator-min-microamp = <10>;
+				regulator-max-microamp = <25000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_touch>;
+		touchscreen-size-x = <880>;
+		touchscreen-size-y = <1280>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@0 {
+			reg = <0>;
+			linux,keycodes = <KEY_HOMEPAGE>;
+		};
+
+		button@1 {
+			reg = <1>;
+			linux,keycodes = <KEY_MENU>;
+		};
+
+		button@2 {
+			reg = <2>;
+			linux,keycodes = <KEY_BACK>;
+		};
+
+		button@3 {
+			reg = <3>;
+			linux,keycodes = <KEY_SEARCH>;
+		};
+
+		button@4 {
+			reg = <4>;
+			linux,keycodes = <KEY_VOLUMEDOWN>;
+		};
+
+		button@5 {
+			reg = <5>;
+			linux,keycodes = <KEY_VOLUMEUP>;
+		};
+
+		button@6 {
+			reg = <6>;
+			linux,keycodes = <KEY_CAMERA>;
+		};
+
+		button@7 {
+			reg = <7>;
+			linux,keycodes = <KEY_POWER>;
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	sy7636a: pmic@62 {
+		compatible = "silergy,sy7636a";
+		reg = <0x62>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_epdpmic>;
+		#thermal-sensor-cells = <0>;
+		epd-pwr-good-gpios = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			reg_epdpmic: vcom {
+				regulator-name = "vcom";
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	assigned-clocks = <&clks IMX7D_UART6_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
+	status = "okay";
+};
+
+&usbotg2 {
+	srp-disable;
+	hnp-disable;
+	status = "okay";
+};
+
+&usdhc2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	vmmc-supply = <&reg_brcm>;
+	bus-width = <4>;
+	non-removable;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc_lpsr {
+	pinctrl_digitizer_reg: digitizerreggrp {
+		fsl,pins = <
+			/* DIGITIZER_PWR_EN */
+			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14
+		>;
+	};
+
+	pinctrl_wacom: wacomgrp {
+		fsl,pins = <
+			/*MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x00000014 FWE */
+			MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4	0x00000074 /* PDCTB */
+			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x00000034 /* WACOM INT */
+			/*MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x00000014 WACOM PWR ENABLE */
+			/*MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x00000074 WACOM RESET */
+		>;
+	};
+};
+
+&iomuxc {
+	pinctrl_bd71815: bd71815grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x59
+		>;
+	};
+
+	pinctrl_brcm_reg: brcmreggrp {
+		fsl,pins = <
+			/* WIFI_PWR_EN */
+			MX7D_PAD_SAI1_TX_BCLK__GPIO6_IO13	0x14
+		>;
+	};
+
+	pinctrl_epdpmic: epdpmicgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21	0x00000074
+			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11	0x00000014
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			/* CYTTSP interrupt */
+			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x54
+			/* CYTTSP reset */
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13		0x04
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
+			MX7D_PAD_I2C1_SCL__I2C1_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x4000007f
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX7D_PAD_I2C3_SDA__I2C3_SDA		0x4000007f
+			MX7D_PAD_I2C3_SCL__I2C3_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX7D_PAD_I2C4_SDA__I2C4_SDA		0x4000007f
+			MX7D_PAD_I2C4_SCL__I2C4_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_touch_reg: touchreggrp {
+		fsl,pins = <
+			/* TOUCH_PWR_EN */
+			MX7D_PAD_GPIO1_IO11__GPIO1_IO11		0x14
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
+			MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x79
+		>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA09__UART6_DCE_TX		0x79
+			MX7D_PAD_EPDC_DATA08__UART6_DCE_RX		0x79
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x59
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x19
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
+		fsl,pins = <
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x5a
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x1a
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x5a
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x5a
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x5a
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x5a
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
+		fsl,pins = <
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x5b
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x1b
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x5b
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x5b
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x5b
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x5b
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x19
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5a
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5a
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5a
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5a
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5a
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x1a
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5b
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5b
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5b
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5b
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5b
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x1b
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_COL__WDOG1_WDOG_ANY	0x74
+		>;
+	};
+
+	pinctrl_wifi: wifigrp {
+		fsl,pins = <
+			/* WiFi Reg On */
+			MX7D_PAD_SD2_CD_B__GPIO5_IO9		0x00000014
+			/* WiFi Sleep 32k */
+			MX7D_PAD_SD1_WP__CCM_CLKO2		0x00000014
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7d-sbc-imx7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sbc-imx7.dts
index f8a868552707..f8a868552707 100644
--- a/arch/arm/boot/dts/imx7d-sbc-imx7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sbc-imx7.dts
diff --git a/arch/arm/boot/dts/imx7d-sdb-reva.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-reva.dts
index 7ce9d8c91985..cabdaa6dc518 100644
--- a/arch/arm/boot/dts/imx7d-sdb-reva.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-reva.dts
@@ -7,6 +7,9 @@
 #include "imx7d-sdb.dts"
 
 / {
+	model = "Freescale i.MX7 SabreSD RevA Board";
+	compatible = "fsl,imx7d-sdb-reva", "fsl,imx7d";
+
 	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
 		pinctrl-0 = <&pinctrl_usb_otg2_vbus_reg_reva>;
 		gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/imx7d-sdb-sht11.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-sht11.dts
index 996555596d40..996555596d40 100644
--- a/arch/arm/boot/dts/imx7d-sdb-sht11.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-sht11.dts
diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
index 869efbc4af42..0462e43ec09b 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
@@ -10,6 +10,11 @@
 	model = "Freescale i.MX7 SabreSD Board";
 	compatible = "fsl,imx7d-sdb", "fsl,imx7d";
 
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+	};
+
 	chosen {
 		stdout-path = &uart1;
 	};
@@ -24,14 +29,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -39,13 +44,13 @@
 		};
 	};
 
-	spi4 {
+	spi-4 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi4>;
-		gpio-sck = <&gpio1 13 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-		cs-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -60,6 +65,17 @@
 		};
 	};
 
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_SD1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <200000>;
+		off-on-delay-us = <20000>;
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -146,6 +162,31 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "fsl,imx7d-evk-wm8960",
+			     "fsl,imx-audio-wm8960";
+		model = "wm8960-audio";
+		audio-cpu = <&sai1>;
+		audio-codec = <&codec>;
+		hp-det-gpio = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+		audio-routing =
+			"Headphone Jack", "HP_L",
+			"Headphone Jack", "HP_R",
+			"Ext Spk", "SPK_LP",
+			"Ext Spk", "SPK_LN",
+			"Ext Spk", "SPK_RP",
+			"Ext Spk", "SPK_RN",
+			"LINPUT1", "AMIC",
+			"AMIC", "MICB";
+	};
+
+	sound-hdmi {
+		compatible = "fsl,imx-audio-sii902x";
+		model = "sii902x-audio";
+		audio-cpu = <&sai3>;
+		hdmi-out;
+	};
 };
 
 &adc1 {
@@ -162,27 +203,26 @@
 	cpu-supply = <&sw1a_reg>;
 };
 
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &ecspi3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	tsc2046@0 {
 		compatible = "ti,tsc2046";
 		reg = <0>;
 		spi-max-frequency = <1000000>;
-		pinctrl-names ="default";
+		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_tsc2046_pendown>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
-		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
@@ -240,7 +280,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -356,9 +396,16 @@
 	codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		wlf,shared-lrclk;
+		wlf,hp-cfg = <2 2 3>;
+		wlf,gpio-cfg = <1 3>;
+		assigned-clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_SRC>,
+				  <&clks IMX7D_PLL_AUDIO_POST_DIV>,
+				  <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
+		assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
+		assigned-clock-rates = <0>, <884736000>, <12288000>;
 	};
 };
 
@@ -387,6 +434,28 @@
 	vin-supply = <&sw2_reg>;
 };
 
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&clks IMX7D_SAI1_ROOT_SRC>,
+			  <&clks IMX7D_PLL_AUDIO_POST_DIV>,
+			  <&clks IMX7D_SAI1_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
+	assigned-clock-rates = <0>, <884736000>, <36864000>;
+	status = "okay";
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3 &pinctrl_sai3_mclk>;
+	assigned-clocks = <&clks IMX7D_SAI3_ROOT_SRC>,
+			  <&clks IMX7D_PLL_AUDIO_POST_DIV>,
+			  <&clks IMX7D_SAI3_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
+	assigned-clock-rates = <0>, <884736000>, <36864000>;
+	status = "okay";
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -420,10 +489,13 @@
 };
 
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
 	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_sd1_vmmc>;
 	wakeup-source;
 	keep-power-in-suspend;
 	status = "okay";
@@ -546,6 +618,7 @@
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
 				MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x34  /* bt reg on */
+				MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x59  /* headphone detect */
 			>;
 		};
 
@@ -611,6 +684,33 @@
 			>;
 		};
 
+		pinctrl_sai1: sai1grp {
+			fsl,pins = <
+				MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
+				MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
+				MX7D_PAD_ENET1_CRS__SAI1_TX_SYNC	0x1f
+				MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
+				MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
+			>;
+		};
+
+		pinctrl_sai2: sai2grp {
+			fsl,pins = <
+				MX7D_PAD_SAI2_TX_BCLK__SAI2_TX_BCLK     0x1f
+				MX7D_PAD_SAI2_TX_SYNC__SAI2_TX_SYNC     0x1f
+				MX7D_PAD_SAI2_TX_DATA__SAI2_TX_DATA0    0x30
+				MX7D_PAD_SAI2_RX_DATA__SAI2_RX_DATA0    0x1f
+			>;
+		};
+
+		pinctrl_sai3: sai3grp {
+			fsl,pins = <
+				MX7D_PAD_UART3_TX_DATA__SAI3_TX_BCLK   0x1f
+				MX7D_PAD_UART3_CTS_B__SAI3_TX_SYNC     0x1f
+				MX7D_PAD_UART3_RTS_B__SAI3_TX_DATA0    0x30
+			>;
+		};
+
 		pinctrl_spi4: spi4grp {
 			fsl,pins = <
 				MX7D_PAD_GPIO1_IO09__GPIO1_IO9	0x59
@@ -650,6 +750,15 @@
 			>;
 		};
 
+		pinctrl_usdhc1_gpio: usdhc1_gpiogrp {
+			fsl,pins = <
+				MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
+				MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
+				MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0x59 /* vmmc */
+				MX7D_PAD_GPIO1_IO08__SD1_VSELECT	0x59 /* VSELECT */
+			>;
+		};
+
 		pinctrl_usdhc1: usdhc1grp {
 			fsl,pins = <
 				MX7D_PAD_SD1_CMD__SD1_CMD		0x59
@@ -658,9 +767,28 @@
 				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
 				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
 				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
-				MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
-				MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
-				MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0x59 /* vmmc */
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+				MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+				MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+				MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+				MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
 			>;
 		};
 
@@ -772,4 +900,10 @@
 			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	  0x14
 		>;
 	};
+
+	pinctrl_sai3_mclk: sai3grp_mclk {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO03__SAI3_MCLK	0x1f
+		>;
+	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-smegw01.dts b/arch/arm/boot/dts/nxp/imx/imx7d-smegw01.dts
new file mode 100644
index 000000000000..7ed27c7ad726
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-smegw01.dts
@@ -0,0 +1,468 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+//
+// Copyright (C) 2020 PHYTEC Messtechnik GmbH
+// Author: Jens Lang  <J.Lang@phytec.de>
+// Copyright (C) 2021 Fabio Estevam <festevam@denx.de>
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "Storopack SMEGW01 board";
+	compatible = "storopack,imx7d-smegw01", "fsl,imx7d";
+
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc2;
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_lte_on: regulator-lte-on {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lte_on>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "lte_on";
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_lte_nreset: regulator-lte-nreset {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lte_nreset>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "LTE_nReset";
+		gpio = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi>;
+		regulator-name = "wifi_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_wlan_rfkill: regulator-wlan-rfkill {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rfkill>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "wlan_rfkill";
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1_pwr_gpio>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 05 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	sram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+
+		ethphy1: ethernet-phy@2 {
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <2>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c_rtc: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		reg = <0x52>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1_lpsr>;
+	dr_mode = "otg";
+	vbus-supply = <&reg_usbotg_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	over-current-active-low;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	wakeup-source;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_wifi>;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	max-frequency = <200000000>;
+	bus-width = <8>;
+	fsl,tuning-step = <1>;
+	non-removable;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	mmc-ddr-1_8v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19	0x04
+			MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x04
+			MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x04
+			MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO	0x04
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x5
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x5
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x5
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x5
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x5
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x5
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x5
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x5
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x5
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x5
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x5
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x5
+			MX7D_PAD_GPIO1_IO10__ENET1_MDIO		0x7
+			MX7D_PAD_GPIO1_IO11__ENET1_MDC		0x7
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x5
+			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC	0x5
+			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0	0x5
+			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1	0x5
+			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2	0x5
+			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3	0x5
+			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0	0x5
+			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1	0x5
+			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2	0x5
+			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3	0x5
+			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x5
+			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC	0x5
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9	0x08
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x40000004
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x40000004
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX	0x0b0b0
+			MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x0b0b0
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x0b0b0
+		>;
+	};
+
+	pinctrl_lte_on: lteongrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x17059
+		>;
+	};
+
+	pinctrl_lte_nreset: ltenresetgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21	0x17059
+		>;
+	};
+
+	pinctrl_rfkill: rfkillgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x17059
+		>;
+	};
+
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x17059
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x74
+			MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x7c
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x7c
+			MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x74
+		>;
+	};
+
+	pinctrl_usbotg1_lpsr: usbotg1grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO04__USB_OTG1_OC	0x04
+		>;
+	};
+
+	pinctrl_usbotg1_pwr: usbotg1-pwrgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO05__USB_OTG1_PWR	0x04
+		>;
+	};
+
+	pinctrl_usbotg1_pwr_gpio: usbotg1-pwr-gpiogrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x04
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_RTS_B__USB_OTG2_OC	0x5c
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x19
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x59
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
+			MX7D_PAD_SD2_CD_B__SD2_CD_B		0x08
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5d
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1d
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5d
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5d
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5d
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5d
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5d
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5d
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5d
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5d
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1d
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5e
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1e
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5e
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5e
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5e
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5e
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5e
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5e
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5e
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5e
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1e
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5f
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x0f
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5f
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5f
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5f
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5f
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5f
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5f
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5f
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5f
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1f
+		>;
+	};
+
+	pinctrl_wifi: wifigrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x04
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x04
+		>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B 0x74
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7d-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-tqma7.dtsi
index 8ad3048dac0d..3ee2017c1ab3 100644
--- a/arch/arm/boot/dts/imx7d-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-tqma7.dtsi
@@ -1,11 +1,15 @@
 // SPDX-License-Identifier: GPL-2.0 OR X11
 /*
- * Device Tree Include file for TQ Systems TQMa7D board with NXP i.MX7Dual SoC.
+ * Device Tree Include file for TQ-Systems TQMa7D board with NXP i.MX7Dual SoC.
  *
- * Copyright (C) 2016 TQ Systems GmbH
+ * Copyright (C) 2016 TQ-Systems GmbH
  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
  * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
  */
 
 #include "imx7d.dtsi"
 #include "imx7-tqma7.dtsi"
+
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
diff --git a/arch/arm/boot/dts/imx7d-zii-rmu2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts
index 2b8d6cc45a53..521493342fe9 100644
--- a/arch/arm/boot/dts/imx7d-zii-rmu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts
@@ -24,7 +24,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -33,13 +33,13 @@
 };
 
 &cpu0 {
-	arm-supply = <&sw1a_reg>;
+	cpu-supply = <&sw1a_reg>;
 };
 
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	flash@0 {
@@ -58,7 +58,7 @@
 			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&fec1_phy>;
 	status = "okay";
 
@@ -204,7 +204,7 @@
 	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx7d-zii-rpu2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rpu2.dts
index 39812c92bf0d..decc19af3b83 100644
--- a/arch/arm/boot/dts/imx7d-zii-rpu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rpu2.dts
@@ -36,7 +36,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -182,7 +182,7 @@
 };
 
 &cpu0 {
-	arm-supply = <&sw1a_reg>;
+	cpu-supply = <&sw1a_reg>;
 };
 
 &clks {
@@ -193,7 +193,7 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	flash@0 {
@@ -607,7 +607,7 @@
 	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
index d8acd7cc7918..0484e349e064 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
@@ -7,12 +7,18 @@
 #include <dt-bindings/reset/imx7-reset.h>
 
 / {
+	aliases {
+		usb0 = &usbotg1;
+		usb1 = &usbotg2;
+		usb2 = &usbh;
+	};
+
 	cpus {
 		cpu0: cpu@0 {
 			clock-frequency = <996000000>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			#cooling-cells = <2>;
-			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cells = <&fuse_grade>;
 			nvmem-cell-names = "speed_grade";
 		};
 
@@ -44,7 +50,7 @@
 			opp-hz = /bits/ 64 <792000000>;
 			opp-microvolt = <1000000>;
 			clock-latency-ns = <150000>;
-			opp-supported-hw = <0xd>, <0xf>;
+			opp-supported-hw = <0xd>, <0x7>;
 			opp-suspend;
 		};
 
@@ -52,7 +58,7 @@
 			opp-hz = /bits/ 64 <996000000>;
 			opp-microvolt = <1100000>;
 			clock-latency-ns = <150000>;
-			opp-supported-hw = <0xc>, <0xf>;
+			opp-supported-hw = <0xc>, <0x7>;
 			opp-suspend;
 		};
 
@@ -60,7 +66,7 @@
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <1225000>;
 			clock-latency-ns = <150000>;
-			opp-supported-hw = <0x8>, <0xf>;
+			opp-supported-hw = <0x8>, <0x3>;
 			opp-suspend;
 		};
 	};
@@ -72,7 +78,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		etm@3007d000 {
 			compatible = "arm,coresight-etm3x", "arm,primecell";
 			reg = <0x3007d000 0x1000>;
@@ -107,6 +113,49 @@
 			      <0x31004000 0x2000>,
 			      <0x31006000 0x2000>;
 		};
+
+		pcie: pcie@33800000 {
+			compatible = "fsl,imx7d-pcie";
+			reg = <0x33800000 0x4000>,
+			      <0x4ff00000 0x80000>;
+			reg-names = "dbi", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			bus-range = <0x00 0xff>;
+			ranges = <0x81000000 0 0          0x4ff80000 0 0x00010000>, /* downstream I/O */
+				 <0x82000000 0 0x40000000 0x40000000 0 0x0ff00000>; /* non-prefetchable memory */
+			num-lanes = <1>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			/*
+			 * Reference manual lists pci irqs incorrectly
+			 * Real hardware ordering is same as imx6: D+MSI, C, B, A
+			 */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
+				 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
+				 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;
+			clock-names = "pcie", "pcie_bus", "pcie_phy";
+			assigned-clocks = <&clks IMX7D_PCIE_CTRL_ROOT_SRC>,
+					  <&clks IMX7D_PCIE_PHY_ROOT_SRC>;
+			assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_250M_CLK>,
+						 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+
+			fsl,max-link-speed = <2>;
+			power-domains = <&pgc_pcie_phy>;
+			resets = <&src IMX7_RESET_PCIEPHY>,
+				 <&src IMX7_RESET_PCIE_CTRL_APPS_EN>,
+				 <&src IMX7_RESET_PCIE_CTRL_APPS_TURNOFF>;
+			reset-names = "pciephy", "apps", "turnoff";
+			fsl,imx7d-pcie-phy = <&pcie_phy>;
+			status = "disabled";
+		};
 	};
 };
 
@@ -116,6 +165,15 @@
 		  reg = <0x306d0000 0x10000>;
 		  status = "disabled";
 	};
+
+	pxp: pxp@30700000 {
+		compatible = "fsl,imx7d-pxp";
+		reg = <0x30700000 0x10000>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX7D_PXP_CLK>;
+		clock-names = "axi";
+	};
 };
 
 &aips3 {
@@ -153,58 +211,12 @@
 			"enet_clk_ref", "enet_out";
 		fsl,num-tx-queues = <3>;
 		fsl,num-rx-queues = <3>;
-		status = "disabled";
-	};
-
-	pcie: pcie@33800000 {
-		compatible = "fsl,imx7d-pcie", "snps,dw-pcie";
-		reg = <0x33800000 0x4000>,
-		      <0x4ff00000 0x80000>;
-		reg-names = "dbi", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		bus-range = <0x00 0xff>;
-		ranges = <0x81000000 0 0          0x4ff80000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x40000000 0x40000000 0 0x0ff00000>; /* non-prefetchable memory */
-		num-lanes = <1>;
-		num-viewport = <4>;
-		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "msi";
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0x7>;
-		/*
-		 * Reference manual lists pci irqs incorrectly
-		 * Real hardware ordering is same as imx6: D+MSI, C, B, A
-		 */
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
-			 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
-			 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;
-		clock-names = "pcie", "pcie_bus", "pcie_phy";
-		assigned-clocks = <&clks IMX7D_PCIE_CTRL_ROOT_SRC>,
-				  <&clks IMX7D_PCIE_PHY_ROOT_SRC>;
-		assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_250M_CLK>,
-					 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
-
-		fsl,max-link-speed = <2>;
-		power-domains = <&pgc_pcie_phy>;
-		resets = <&src IMX7_RESET_PCIEPHY>,
-			 <&src IMX7_RESET_PCIE_CTRL_APPS_EN>,
-			 <&src IMX7_RESET_PCIE_CTRL_APPS_TURNOFF>;
-		reset-names = "pciephy", "apps", "turnoff";
-		fsl,imx7d-pcie-phy = <&pcie_phy>;
+		fsl,stop-mode = <&gpr 0x10 4>;
 		status = "disabled";
 	};
 };
 
 &ca_funnel_in_ports {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	port@1 {
 		reg = <1>;
 		ca_funnel_in_port1: endpoint {
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-aster.dts
new file mode 100644
index 000000000000..58ebb02d948a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-aster.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ *
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Aster Carrier Board";
+	compatible = "toradex,colibri-imx7s-aster",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-eval-v3.dts
new file mode 100644
index 000000000000..38de76630d6a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-eval-v3.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx7s-eval-v3",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris-v2.dts
new file mode 100644
index 000000000000..72b5c17ab1ab
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris-v2.dts
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris-v2",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris.dts
new file mode 100644
index 000000000000..26ba72c17feb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx7s-colibri.dtsi
new file mode 100644
index 000000000000..ef51395d3537
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+#include "imx7s.dtsi"
+#include "imx7-colibri.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+/* NAND */
+&gpmi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-mba7.dts b/arch/arm/boot/dts/nxp/imx/imx7s-mba7.dts
index a143d566a38b..8e4cf589c92c 100644
--- a/arch/arm/boot/dts/imx7s-mba7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-mba7.dts
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0 OR X11
 /*
- * Device Tree Source for TQ Systems TQMa7S board on MBa7 carrier board.
+ * Device Tree Source for TQ-Systems TQMa7S board on MBa7 carrier board.
  *
- * Copyright (C) 2016 TQ Systems GmbH
+ * Copyright (C) 2016 TQ-Systems GmbH
  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
  * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
  */
@@ -13,6 +13,6 @@
 #include "imx7-mba7.dtsi"
 
 / {
-	model = "TQ Systems TQMa7S board on MBa7 carrier board";
-	compatible = "tq,imx7s-mba7", "fsl,imx7s";
+	model = "TQ-Systems TQMa7S board on MBa7 carrier board";
+	compatible = "tq,imx7s-mba7", "tq,imx7s-tqma7", "fsl,imx7s";
 };
diff --git a/arch/arm/boot/dts/imx7s-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7s-tqma7.dtsi
index 5f5433eb7dd7..7a190fdb2d30 100644
--- a/arch/arm/boot/dts/imx7s-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-tqma7.dtsi
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0 OR X11
 /*
- * Device Tree Include file for TQ Systems TQMa7S board with NXP i.MX7Solo SoC.
+ * Device Tree Include file for TQ-Systems TQMa7S board with NXP i.MX7Solo SoC.
  *
- * Copyright (C) 2016 TQ Systems GmbH
+ * Copyright (C) 2016 TQ-Systems GmbH
  * Author: Markus Niebel <Markus.Niebel@tq-group.com>
  * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
  */
diff --git a/arch/arm/boot/dts/imx7s-warp.dts b/arch/arm/boot/dts/nxp/imx/imx7s-warp.dts
index d6b4888fa686..ba7231b364bb 100644
--- a/arch/arm/boot/dts/imx7s-warp.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-warp.dts
@@ -10,8 +10,8 @@
 #include "imx7s.dtsi"
 
 / {
-	model = "Warp i.MX7 Board";
-	compatible = "warp,imx7s-warp", "fsl,imx7s";
+	model = "Element14 Warp i.MX7 Board";
+	compatible = "element14,imx7s-warp", "fsl,imx7s";
 
 	memory@80000000 {
 		device_type = "memory";
@@ -75,7 +75,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&codec>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -94,7 +94,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -232,7 +232,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sai1_mclk>;
 		VDDA-supply = <&vgen4_reg>;
@@ -248,17 +248,17 @@
 
 &mipi_csi {
 	clock-frequency = <166000000>;
-	fsl,csis-hs-settle = <3>;
 	status = "okay";
 
-	port@0 {
-		reg = <0>;
+	ports {
+		port@0 {
+			reg = <0>;
 
-		mipi_from_sensor: endpoint {
-			remote-endpoint = <&ov2680_to_mipi>;
-			data-lanes = <1>;
+			mipi_from_sensor: endpoint {
+				remote-endpoint = <&ov2680_to_mipi>;
+				data-lanes = <1>;
+			};
 		};
-
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/nxp/imx/imx7s.dtsi
index 1b812f4e7453..ebf7befcc11e 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7s.dtsi
@@ -47,6 +47,8 @@
 		spi1 = &ecspi2;
 		spi2 = &ecspi3;
 		spi3 = &ecspi4;
+		usb0 = &usbotg1;
+		usb1 = &usbh;
 	};
 
 	cpus {
@@ -74,6 +76,22 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clks IMX7D_CLK_ARM>;
 			cpu-idle-states = <&cpu_sleep_wait>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+			nvmem-cells = <&fuse_grade>;
+			nvmem-cell-names = "speed_grade";
+		};
+	};
+
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-792000000 {
+			opp-hz = /bits/ 64 <792000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <150000>;
+			opp-supported-hw = <0xf>, <0xf>;
 		};
 	};
 
@@ -102,6 +120,7 @@
 		compatible = "usb-nop-xceiv";
 		clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_hsic_phy>;
 		#phy-cells = <0>;
 	};
 
@@ -147,19 +166,9 @@
 		};
 	};
 
-	tempmon: tempmon {
-		compatible = "fsl,imx7d-tempmon";
-		interrupt-parent = <&gpc>;
-		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-		fsl,tempmon = <&anatop>;
-		nvmem-cells = <&tempmon_calib>,
-			<&tempmon_temp_grade>;
-		nvmem-cell-names = "calib", "temp_grade";
-		clocks = <&clks IMX7D_PLL_SYS_MAIN_CLK>;
-	};
-
 	timer {
 		compatible = "arm,armv7-timer";
+		arm,cpu-registers-not-fw-configured;
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
@@ -167,13 +176,22 @@
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&gpc>;
 		ranges;
 
+		ocram: sram@900000 {
+			compatible = "mmio-sram";
+			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&clks IMX7D_OCRAM_CLK>;
+		};
+
 		funnel@30041000 {
 			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x30041000 0x1000>;
@@ -181,7 +199,11 @@
 			clock-names = "apb_pclk";
 
 			ca_funnel_in_ports: in-ports {
-				port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
 					ca_funnel_in_port0: endpoint {
 						remote-endpoint = <&etm0_out_port>;
 					};
@@ -316,7 +338,7 @@
 			      <0x31006000 0x2000>;
 		};
 
-		aips1: aips-bus@30000000 {
+		aips1: bus@30000000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -407,14 +429,14 @@
 				gpio-ranges = <&iomuxc 0 139 16>;
 			};
 
-			wdog1: wdog@30280000 {
+			wdog1: watchdog@30280000 {
 				compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
 				reg = <0x30280000 0x10000>;
 				interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_WDOG1_ROOT_CLK>;
 			};
 
-			wdog2: wdog@30290000 {
+			wdog2: watchdog@30290000 {
 				compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
 				reg = <0x30290000 0x10000>;
 				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
@@ -422,7 +444,7 @@
 				status = "disabled";
 			};
 
-			wdog3: wdog@302a0000 {
+			wdog3: watchdog@302a0000 {
 				compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
 				reg = <0x302a0000 0x10000>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
@@ -430,7 +452,7 @@
 				status = "disabled";
 			};
 
-			wdog4: wdog@302b0000 {
+			wdog4: watchdog@302b0000 {
 				compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
 				reg = <0x302b0000 0x10000>;
 				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
@@ -438,14 +460,14 @@
 				status = "disabled";
 			};
 
-			iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+			iomuxc_lpsr: pinctrl@302c0000 {
 				compatible = "fsl,imx7d-iomuxc-lpsr";
 				reg = <0x302c0000 0x10000>;
 				fsl,input-sel = <&iomuxc>;
 			};
 
-			gpt1: gpt@302d0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+			gpt1: timer@302d0000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302d0000 0x10000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT1_ROOT_CLK>,
@@ -453,8 +475,8 @@
 				clock-names = "ipg", "per";
 			};
 
-			gpt2: gpt@302e0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+			gpt2: timer@302e0000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302e0000 0x10000>;
 				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT2_ROOT_CLK>,
@@ -463,8 +485,8 @@
 				status = "disabled";
 			};
 
-			gpt3: gpt@302f0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+			gpt3: timer@302f0000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302f0000 0x10000>;
 				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT3_ROOT_CLK>,
@@ -473,8 +495,8 @@
 				status = "disabled";
 			};
 
-			gpt4: gpt@30300000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+			gpt4: timer@30300000 {
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x30300000 0x10000>;
 				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT4_ROOT_CLK>,
@@ -483,7 +505,7 @@
 				status = "disabled";
 			};
 
-			kpp: kpp@30320000 {
+			kpp: keypad@30320000 {
 				compatible = "fsl,imx7d-kpp", "fsl,imx21-kpp";
 				reg = <0x30320000 0x10000>;
 				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
@@ -491,7 +513,7 @@
 				status = "disabled";
 			};
 
-			iomuxc: iomuxc@30330000 {
+			iomuxc: pinctrl@30330000 {
 				compatible = "fsl,imx7d-iomuxc";
 				reg = <0x30330000 0x10000>;
 			};
@@ -504,7 +526,7 @@
 
 				mux: mux-controller {
 					compatible = "mmio-mux";
-					#mux-control-cells = <0>;
+					#mux-control-cells = <1>;
 					mux-reg-masks = <0x14 0x00000010>;
 				};
 
@@ -537,7 +559,7 @@
 				};
 			};
 
-			ocotp: ocotp-ctrl@30350000 {
+			ocotp: efuse@30350000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx7d-ocotp", "syscon";
@@ -548,11 +570,7 @@
 					reg = <0x3c 0x4>;
 				};
 
-				tempmon_temp_grade: temp-grade@10 {
-					reg = <0x10 0x4>;
-				};
-
-				cpu_speed_grade: speed-grade@10 {
+				fuse_grade: fuse-grade@10 {
 					reg = <0x10 0x4>;
 				};
 			};
@@ -591,6 +609,17 @@
 					anatop-max-voltage = <1300000>;
 					anatop-enable-bit = <0>;
 				};
+
+				tempmon: tempmon {
+					compatible = "fsl,imx7d-tempmon";
+					interrupt-parent = <&gpc>;
+					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+					fsl,tempmon = <&anatop>;
+					nvmem-cells = <&tempmon_calib>,	<&fuse_grade>;
+					nvmem-cell-names = "calib", "temp_grade";
+					clocks = <&clks IMX7D_PLL_SYS_MAIN_CLK>;
+					#thermal-sensor-cells = <0>;
+				};
 			};
 
 			snvs: snvs@30370000 {
@@ -611,13 +640,15 @@
 					compatible = "fsl,sec-v4.0-pwrkey";
 					regmap = <&snvs>;
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX7D_SNVS_CLK>;
+					clock-names = "snvs-pwrkey";
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
 					status = "disabled";
 				};
 			};
 
-			clks: ccm@30380000 {
+			clks: clock-controller@30380000 {
 				compatible = "fsl,imx7d-ccm";
 				reg = <0x30380000 0x10000>;
 				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
@@ -627,7 +658,7 @@
 				clock-names = "ckil", "osc";
 			};
 
-			src: src@30390000 {
+			src: reset-controller@30390000 {
 				compatible = "fsl,imx7d-src", "syscon";
 				reg = <0x30390000 0x10000>;
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
@@ -641,7 +672,6 @@
 				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <3>;
 				interrupt-parent = <&intc>;
-				#power-domain-cells = <1>;
 
 				pgc {
 					#address-cells = <1>;
@@ -658,11 +688,17 @@
 						reg = <1>;
 						power-supply = <&reg_1p0d>;
 					};
+
+					pgc_hsic_phy: power-domain@2 {
+						#power-domain-cells = <0>;
+						reg = <2>;
+						power-supply = <&reg_1p2>;
+					};
 				};
 			};
 		};
 
-		aips2: aips-bus@30400000 {
+		aips2: bus@30400000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -698,6 +734,36 @@
 				clocks = <&clks IMX7D_ECSPI4_ROOT_CLK>,
 					<&clks IMX7D_ECSPI4_ROOT_CLK>;
 				clock-names = "ipg", "per";
+				dma-names = "rx", "tx";
+				dmas = <&sdma 6 7 1>, <&sdma 7 7 2>;
+				status = "disabled";
+			};
+
+			ftm1: pwm@30640000 {
+				compatible = "fsl,vf610-ftm-pwm";
+				reg = <0x30640000 0x10000>;
+				#pwm-cells = <3>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "ftm_sys", "ftm_ext",
+				"ftm_fix", "ftm_cnt_clk_en";
+				clocks = <&clks IMX7D_FLEXTIMER1_ROOT_CLK>,
+					<&clks IMX7D_FLEXTIMER1_ROOT_CLK>,
+					<&clks IMX7D_FLEXTIMER1_ROOT_CLK>,
+					<&clks IMX7D_FLEXTIMER1_ROOT_CLK>;
+				status = "disabled";
+			};
+
+			ftm2: pwm@30650000 {
+				compatible = "fsl,vf610-ftm-pwm";
+				reg = <0x30650000 0x10000>;
+				#pwm-cells = <3>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "ftm_sys", "ftm_ext",
+				"ftm_fix", "ftm_cnt_clk_en";
+				clocks = <&clks IMX7D_FLEXTIMER2_ROOT_CLK>,
+					<&clks IMX7D_FLEXTIMER2_ROOT_CLK>,
+					<&clks IMX7D_FLEXTIMER2_ROOT_CLK>,
+					<&clks IMX7D_FLEXTIMER2_ROOT_CLK>;
 				status = "disabled";
 			};
 
@@ -749,10 +815,8 @@
 				compatible = "fsl,imx7-csi";
 				reg = <0x30710000 0x10000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks IMX7D_CLK_DUMMY>,
-					 <&clks IMX7D_CSI_MCLK_ROOT_CLK>,
-					 <&clks IMX7D_CLK_DUMMY>;
-				clock-names = "axi", "mclk", "dcic";
+				clocks = <&clks IMX7D_CSI_MCLK_ROOT_CLK>;
+				clock-names = "mclk";
 				status = "disabled";
 
 				port {
@@ -763,20 +827,28 @@
 			};
 
 			lcdif: lcdif@30730000 {
-				compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx7d-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x30730000 0x10000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
 					<&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>;
 				clock-names = "pix", "axi";
 				status = "disabled";
+
+				port {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					lcdif_out_mipi_dsi: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&mipi_dsi_in_lcdif>;
+					};
+				};
 			};
 
 			mipi_csi: mipi-csi@30750000 {
 				compatible = "fsl,imx7-mipi-csi2";
 				reg = <0x30750000 0x10000>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_IPG_ROOT_CLK>,
 					 <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
@@ -785,24 +857,64 @@
 				power-domains = <&pgc_mipi_phy>;
 				phy-supply = <&reg_1p0d>;
 				resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
-				reset-names = "mrst";
 				status = "disabled";
 
-				port@0 {
-					reg = <0>;
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mipi_vc0_to_csi_mux: endpoint {
+							remote-endpoint = <&csi_mux_from_mipi_vc0>;
+						};
+					};
 				};
+			};
 
-				port@1 {
-					reg = <1>;
+			mipi_dsi: dsi@30760000 {
+				compatible = "fsl,imx7d-mipi-dsim", "fsl,imx8mm-mipi-dsim";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x30760000 0x400>;
+				clocks = <&clks IMX7D_MIPI_DSI_ROOT_CLK>,
+					 <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
+				clock-names = "bus_clk", "sclk_mipi";
+				assigned-clocks = <&clks IMX7D_MIPI_DSI_ROOT_SRC>,
+						  <&clks IMX7D_PLL_SYS_PFD5_CLK>;
+				assigned-clock-parents = <&clks IMX7D_PLL_SYS_PFD5_CLK>;
+				assigned-clock-rates = <0>, <333000000>;
+				power-domains = <&pgc_mipi_phy>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+				samsung,burst-clock-frequency = <891000000>;
+				samsung,esc-clock-frequency = <20000000>;
+				samsung,pll-clock-frequency = <24000000>;
+				status = "disabled";
 
-					mipi_vc0_to_csi_mux: endpoint {
-						remote-endpoint = <&csi_mux_from_mipi_vc0>;
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						mipi_dsi_in_lcdif: endpoint@0 {
+							reg = <0>;
+							remote-endpoint = <&lcdif_out_mipi_dsi>;
+						};
 					};
 				};
 			};
 		};
 
-		aips3: aips-bus@30800000 {
+		aips3: bus@30800000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -825,6 +937,8 @@
 					clocks = <&clks IMX7D_ECSPI1_ROOT_CLK>,
 						<&clks IMX7D_ECSPI1_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 0 7 1>, <&sdma 1 7 2>;
 					status = "disabled";
 				};
 
@@ -837,6 +951,8 @@
 					clocks = <&clks IMX7D_ECSPI2_ROOT_CLK>,
 						<&clks IMX7D_ECSPI2_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 2 7 1>, <&sdma 3 7 2>;
 					status = "disabled";
 				};
 
@@ -849,6 +965,8 @@
 					clocks = <&clks IMX7D_ECSPI3_ROOT_CLK>,
 						<&clks IMX7D_ECSPI3_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 4 7 1>, <&sdma 5 7 2>;
 					status = "disabled";
 				};
 
@@ -931,7 +1049,7 @@
 				};
 			};
 
-			crypto: caam@30900000 {
+			crypto: crypto@30900000 {
 				compatible = "fsl,sec-v4.0";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -942,19 +1060,19 @@
 					 <&clks IMX7D_AHB_CHANNEL_ROOT_CLK>;
 				clock-names = "ipg", "aclk";
 
-				sec_jr0: jr0@1000 {
+				sec_jr0: jr@1000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr1: jr1@2000 {
+				sec_jr1: jr@2000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x2000 0x1000>;
 					interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr2: jr1@3000 {
+				sec_jr2: jr@3000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x3000 0x1000>;
 					interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
@@ -968,7 +1086,7 @@
 				clocks = <&clks IMX7D_CLK_DUMMY>,
 					<&clks IMX7D_CAN1_ROOT_CLK>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x10 1 0x10 17>;
+				fsl,stop-mode = <&gpr 0x10 1>;
 				status = "disabled";
 			};
 
@@ -979,7 +1097,7 @@
 				clocks = <&clks IMX7D_CLK_DUMMY>,
 					<&clks IMX7D_CAN2_ROOT_CLK>;
 				clock-names = "ipg", "per";
-				fsl,stop-mode = <&gpr 0x10 2 0x10 18>;
+				fsl,stop-mode = <&gpr 0x10 2>;
 				status = "disabled";
 			};
 
@@ -1122,7 +1240,7 @@
 				reg = <0x30b30200 0x200>;
 			};
 
-			usdhc1: usdhc@30b40000 {
+			usdhc1: mmc@30b40000 {
 				compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x30b40000 0x10000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -1131,10 +1249,12 @@
 					<&clks IMX7D_USDHC1_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
-			usdhc2: usdhc@30b50000 {
+			usdhc2: mmc@30b50000 {
 				compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x30b50000 0x10000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -1143,10 +1263,12 @@
 					<&clks IMX7D_USDHC2_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
-			usdhc3: usdhc@30b60000 {
+			usdhc3: mmc@30b60000 {
 				compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
 				reg = <0x30b60000 0x10000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
@@ -1155,10 +1277,25 @@
 					<&clks IMX7D_USDHC3_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
+				status = "disabled";
+			};
+
+			qspi: spi@30bb0000 {
+				compatible = "fsl,imx7d-qspi";
+				reg = <0x30bb0000 0x10000>, <0x60000000 0x10000000>;
+				reg-names = "QuadSPI", "QuadSPI-memory";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_QSPI_ROOT_CLK>,
+					<&clks IMX7D_QSPI_ROOT_CLK>;
+				clock-names = "qspi_en", "qspi";
 				status = "disabled";
 			};
 
-			sdma: sdma@30bd0000 {
+			sdma: dma-controller@30bd0000 {
 				compatible = "fsl,imx7d-sdma", "fsl,imx35-sdma";
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -1186,27 +1323,27 @@
 					"enet_clk_ref", "enet_out";
 				fsl,num-tx-queues = <3>;
 				fsl,num-rx-queues = <3>;
+				fsl,stop-mode = <&gpr 0x10 3>;
 				status = "disabled";
 			};
 		};
 
-		dma_apbh: dma-apbh@33000000 {
+		dma_apbh: dma-controller@33000000 {
 			compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x33000000 0x2000>;
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
 		};
 
-		gpmi: gpmi-nand@33002000{
+		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx7ulp-com.dts b/arch/arm/boot/dts/nxp/imx/imx7ulp-com.dts
new file mode 100644
index 000000000000..d76fea3b35c6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp-com.dts
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2019 NXP
+
+/dts-v1/;
+
+#include "imx7ulp.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Embedded Artists i.MX7ULP COM";
+	compatible = "ea,imx7ulp-com", "fsl,imx7ulp";
+
+	chosen {
+		stdout-path = &lpuart4;
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x4000000>;
+	};
+};
+
+&lpuart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1_id>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usdhc0 {
+	assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>;
+	assigned-clock-parents = <&scg1 IMX7ULP_CLK_APLL_PFD1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc0>;
+	non-removable;
+	bus-width = <8>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&iomuxc1 {
+	pinctrl_lpuart4: lpuart4grp {
+		fsl,pins = <
+			IMX7ULP_PAD_PTC3__LPUART4_RX	0x3
+			IMX7ULP_PAD_PTC2__LPUART4_TX	0x3
+		>;
+	};
+
+	pinctrl_usbotg1_id: otg1idgrp {
+		fsl,pins = <
+			IMX7ULP_PAD_PTC13__USB0_ID	0x10003
+		>;
+	};
+
+	pinctrl_usdhc0: usdhc0grp {
+		fsl,pins = <
+			IMX7ULP_PAD_PTD1__SDHC0_CMD	0x43
+			IMX7ULP_PAD_PTD2__SDHC0_CLK	0x10042
+			IMX7ULP_PAD_PTD3__SDHC0_D7	0x43
+			IMX7ULP_PAD_PTD4__SDHC0_D6	0x43
+			IMX7ULP_PAD_PTD5__SDHC0_D5	0x43
+			IMX7ULP_PAD_PTD6__SDHC0_D4	0x43
+			IMX7ULP_PAD_PTD7__SDHC0_D3	0x43
+			IMX7ULP_PAD_PTD8__SDHC0_D2	0x43
+			IMX7ULP_PAD_PTD9__SDHC0_D1	0x43
+			IMX7ULP_PAD_PTD10__SDHC0_D0	0x43
+			IMX7ULP_PAD_PTD11__SDHC0_DQS	0x42
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7ulp-evk.dts b/arch/arm/boot/dts/nxp/imx/imx7ulp-evk.dts
index a863a2b337d6..eff51e113db4 100644
--- a/arch/arm/boot/dts/imx7ulp-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp-evk.dts
@@ -72,7 +72,7 @@
 	srp-disable;
 	hnp-disable;
 	adp-disable;
-	over-current-active-low;
+	disable-over-current;
 	status = "okay";
 };
 
@@ -110,7 +110,6 @@
 	pinctrl_usbotg1_id: otg1idgrp {
 		fsl,pins = <
 			IMX7ULP_PAD_PTC13__USB0_ID	0x10003
-			IMX7ULP_PAD_PTC16__USB1_OC2	0x10003
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx7ulp-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx7ulp-pinfunc.h
index c0148d79b62d..c0148d79b62d 100644
--- a/arch/arm/boot/dts/imx7ulp-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp-pinfunc.h
diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/nxp/imx/imx7ulp.dtsi
index d37a1927c88e..ac338320ac1d 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp.dtsi
@@ -37,10 +37,10 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu0: cpu@0 {
+		cpu0: cpu@f00 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
-			reg = <0>;
+			reg = <0xf00>;
 		};
 	};
 
@@ -132,13 +132,13 @@
 				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
 			clock-names = "aclk", "ipg";
 
-			sec_jr0: jr0@1000 {
+			sec_jr0: jr@1000 {
 				compatible = "fsl,sec-v4.0-job-ring";
 				reg = <0x1000 0x1000>;
 				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sec_jr1: jr1@2000 {
+			sec_jr1: jr@2000 {
 				compatible = "fsl,sec-v4.0-job-ring";
 				reg = <0x2000 0x1000>;
 				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -189,7 +189,7 @@
 		};
 
 		usbotg1: usb@40330000 {
-			compatible = "fsl,imx7ulp-usb", "fsl,imx6ul-usb";
+			compatible = "fsl,imx7ulp-usb", "fsl,imx6ul-usb", "fsl,imx27-usb";
 			reg = <0x40330000 0x200>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_USB0>;
@@ -202,13 +202,14 @@
 		};
 
 		usbmisc1: usbmisc@40330200 {
-			compatible = "fsl,imx7ulp-usbmisc", "fsl,imx7d-usbmisc";
+			compatible = "fsl,imx7ulp-usbmisc", "fsl,imx7d-usbmisc",
+				     "fsl,imx6q-usbmisc";
 			#index-cells = <1>;
 			reg = <0x40330200 0x200>;
 		};
 
 		usbphy1: usb-phy@40350000 {
-			compatible = "fsl,imx7ulp-usbphy", "fsl,imx6ul-usbphy";
+			compatible = "fsl,imx7ulp-usbphy";
 			reg = <0x40350000 0x1000>;
 			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_USB_PHY>;
@@ -259,7 +260,7 @@
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_WDG1>;
 			assigned-clocks = <&pcc2 IMX7ULP_CLK_WDG1>;
-			assigned-clocks-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>;
 			timeout-sec = <40>;
 		};
 
@@ -328,8 +329,9 @@
 			compatible = "fsl,imx7ulp-lpi2c";
 			reg = <0x40a40000 0x10000>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
-			clock-names = "ipg";
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>,
+				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
+			clock-names = "per", "ipg";
 			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
 			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
 			assigned-clock-rates = <48000000>;
@@ -340,8 +342,9 @@
 			compatible = "fsl,imx7ulp-lpi2c";
 			reg = <0x40a50000 0x10000>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
-			clock-names = "ipg";
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>,
+				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
+			clock-names = "per", "ipg";
 			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
 			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
 			assigned-clock-rates = <48000000>;
@@ -394,7 +397,7 @@
 			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
 				 <&pcc3 IMX7ULP_CLK_PCTLC>;
 			clock-names = "gpio", "port";
-			gpio-ranges = <&iomuxc1 0 0 32>;
+			gpio-ranges = <&iomuxc1 0 0 20>;
 		};
 
 		gpio_ptd: gpio@40af0000 {
@@ -408,7 +411,7 @@
 			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
 				 <&pcc3 IMX7ULP_CLK_PCTLD>;
 			clock-names = "gpio", "port";
-			gpio-ranges = <&iomuxc1 0 32 32>;
+			gpio-ranges = <&iomuxc1 0 32 12>;
 		};
 
 		gpio_pte: gpio@40b00000 {
@@ -422,7 +425,7 @@
 			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
 				 <&pcc3 IMX7ULP_CLK_PCTLE>;
 			clock-names = "gpio", "port";
-			gpio-ranges = <&iomuxc1 0 64 32>;
+			gpio-ranges = <&iomuxc1 0 64 16>;
 		};
 
 		gpio_ptf: gpio@40b10000 {
@@ -436,7 +439,7 @@
 			clocks = <&pcc2 IMX7ULP_CLK_RGPIO2P1>,
 				 <&pcc3 IMX7ULP_CLK_PCTLF>;
 			clock-names = "gpio", "port";
-			gpio-ranges = <&iomuxc1 0 96 32>;
+			gpio-ranges = <&iomuxc1 0 96 20>;
 		};
 	};
 
@@ -452,10 +455,12 @@
 			reg = <0x410a3000 0x1000>;
 		};
 
-		ocotp: ocotp-ctrl@410a6000 {
+		ocotp: efuse@410a6000 {
 			compatible = "fsl,imx7ulp-ocotp", "syscon";
 			reg = <0x410a6000 0x4000>;
 			clocks = <&scg1 IMX7ULP_CLK_DUMMY>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1050-evk.dts b/arch/arm/boot/dts/nxp/imx/imxrt1050-evk.dts
new file mode 100644
index 000000000000..6a9c10decf52
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1050-evk.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+/dts-v1/;
+#include "imxrt1050.dtsi"
+#include "imxrt1050-pinfunc.h"
+
+/ {
+	model = "NXP IMXRT1050-evk board";
+	compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	aliases {
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		mmc0 = &usdhc1;
+		serial0 = &lpuart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x2000000>;
+	};
+};
+
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl_lpuart1: lpuart1grp {
+		fsl,pins = <
+			MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD	0xf1
+			MXRT1050_IOMUXC_GPIO_AD_B0_13_LPUART1_RXD	0xf1
+		>;
+	};
+
+	pinctrl_usdhc0: usdhc0grp {
+		fsl,pins = <
+			MXRT1050_IOMUXC_GPIO_B1_12_USDHC1_CD_B		0x1B000
+			MXRT1050_IOMUXC_GPIO_B1_14_USDHC1_VSELECT	0xB069
+			MXRT1050_IOMUXC_GPIO_SD_B0_00_USDHC1_CMD	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_01_USDHC1_CLK	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0	0x17061
+		>;
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc0>;
+	pinctrl-1 = <&pinctrl_usdhc0>;
+	pinctrl-2 = <&pinctrl_usdhc0>;
+	pinctrl-3 = <&pinctrl_usdhc0>;
+	cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1050-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imxrt1050-pinfunc.h
new file mode 100644
index 000000000000..22c14a3262ad
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1050-pinfunc.h
@@ -0,0 +1,993 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_IMXRT1050_PINFUNC_H
+#define _DT_BINDINGS_PINCTRL_IMXRT1050_PINFUNC_H
+
+#define IMX_PAD_SION	0x40000000
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+
+#define MXRT1050_IOMUXC_GPIO_EMC_00_SEMC_DA00				0x014 0x204 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_FLEXPWM4_PWM0_A			0x014 0x204 0x494 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_LPSPI2_SCK				0x014 0x204 0x500 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_00_XBAR_INOUT2				0x014 0x204 0x60C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_FLEXIO1_D00				0x014 0x204 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_GPIO4_IO00				0x014 0x204 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_01_SEMC_DA01				0x018 0x208 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_FLEXPWM4_PWM0_B			0x018 0x208 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_LPSPI2_PCS0				0x018 0x208 0x4FC 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_01_XBAR_INOUT3				0x018 0x208 0x610 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_FLEXIO1_D01				0x018 0x208 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_GPIO4_IO01				0x018 0x208 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_02_SEMC_DA02				0x01C 0x20C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_FLEXPWM4_PWM1_A			0x01C 0x20C 0x498 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_LPSPI2_SDO				0x01C 0x20C 0x508 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_02_XBAR_INOUT4				0x01C 0x20C 0x614 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_FLEXIO1_D02				0x01C 0x20C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_GPIO4_IO02				0x01C 0x20C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_03_SEMC_DA03				0x020 0x210 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_FLEXPWM4_PWM1_B			0x020 0x210 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_LPSPI2_SDI				0x020 0x210 0x504 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_03_XBAR_INOUT5				0x020 0x210 0x618 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_FLEXIO1_D03				0x020 0x210 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_GPIO4_IO03				0x020 0x210 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_04_SEMC_DA04				0x024 0x214 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_FLEXPWM4_PWM2_A			0x024 0x214 0x49C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_SAI2_TX_DATA			0x024 0x214 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_XBAR_INOUT6				0x024 0x214 0x61C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_FLEXIO1_D04				0x024 0x214 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_GPIO4_IO04				0x024 0x214 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_05_SEMC_DA05				0x028 0x218 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_FLEXPWM4_PWM2_B			0x028 0x218 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_SAI2_TX_SYNC			0x028 0x218 0x5C4 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_XBAR_INOUT7				0x028 0x218 0x620 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_FLEXIO1_D05				0x028 0x218 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_GPIO4_IO05				0x028 0x218 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_06_SEMC_DA06				0x02C 0x21C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_FLEXPWM2_PWM0_A			0x02C 0x21C 0x478 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_SAI2_TX_BCLK			0x02C 0x21C 0x5C0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_XBAR_INOUT8				0x02C 0x21C 0x624 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_FLEXIO1_D06				0x02C 0x21C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_GPIO4_IO06				0x02C 0x21C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_07_SEMC_DA07				0x030 0x220 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_FLEXPWM2_PWM0_B			0x030 0x220 0x488 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_SAI2_MCLK				0x030 0x220 0x5B0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_XBAR_INOUT9				0x030 0x220 0x628 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_FLEXIO1_D07				0x030 0x220 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_GPIO4_IO07				0x030 0x220 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_08_SEMC_DM00				0x034 0x224 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_FLEXPWM2_PWM1_A			0x034 0x224 0x47C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_SAI2_RX_DATA			0x034 0x224 0x5B8 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_XBAR_INOUT17			0x034 0x224 0x62C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_FLEXIO1_D08				0x034 0x224 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_GPIO4_IO08				0x034 0x224 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_09_SEMC_ADDR00				0x038 0x228 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_FLEXPWM2_PWM1_B			0x038 0x228 0x48C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_SAI2_RX_SYNC			0x038 0x228 0x5BC 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_FLEXCAN2_TX				0x038 0x228 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_FLEXIO1_D09				0x038 0x228 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_GPIO4_IO09				0x038 0x228 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_10_SEMC_ADDR01				0x03C 0x22C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_FLEXPWM2_PWM2_A			0x03C 0x22C 0x480 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_SAI2_RX_BCLK			0x03C 0x22C 0x5B4 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_FLEXCAN2_RX				0x03C 0x22C 0x450 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_FLEXIO1_D10				0x03C 0x22C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_GPIO4_IO10				0x03C 0x22C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_11_SEMC_ADDR02				0x040 0x230 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_FLEXPWM2_PWM2_B			0x040 0x230 0x490 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_LPI2C4_SDA				0x040 0x230 0x4E8 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_USDHC2_RESET_B			0x040 0x230 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_FLEXIO1_D11				0x040 0x230 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_GPIO4_IO11				0x040 0x230 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_12_SEMC_ADDR03				0x044 0x234 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_XBAR_INOUT24			0x044 0x234 0x640 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_LPI2C4_SCL				0x044 0x234 0x4E4 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_USDHC2_WP				0x044 0x234 0x5D8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_FLEXPWM1_PWM3_A			0x044 0x234 0x454 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_12_GPIO4_IO12				0x044 0x234 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_13_SEMC_ADDR04				0x048 0x238 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_13_XBAR_INOUT25			0x048 0x238 0x650 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_13_LPUART3_TXD				0x048 0x238 0x53C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_13_MQS_RIGHT				0x048 0x238 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_13_FLEXPWM1_PWM3_B			0x048 0x238 0x464 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_13_GPIO4_IO13				0x048 0x238 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_14_SEMC_ADDR05				0x04C 0x23C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_XBAR_INOUT19			0x04C 0x23C 0x654 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_LPUART3_RXD				0x04C 0x23C 0x538 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_MQS_LEFT				0x04C 0x23C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_LPSPI2_PCS1				0x04C 0x23C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_GPIO4_IO14				0x04C 0x23C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_15_SEMC_ADDR06				0x050 0x240 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_XBAR_INOUT20			0x050 0x240 0x634 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_LPUART3_CTS_B			0x050 0x240 0x534 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_SPDIF_OUT				0x050 0x240 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_TMR3_TIMER0				0x050 0x240 0x57C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_GPIO4_IO15				0x050 0x240 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_16_SEMC_ADDR07				0x054 0x244 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_XBAR_INOUT21			0x054 0x244 0x658 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_LPUART3_RTS_B			0x054 0x244 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_SPDIF_IN				0x054 0x244 0x5C8 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_16_TMR3_TIMER1				0x054 0x244 0x580 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_GPIO4_IO16				0x054 0x244 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_17_SEMC_ADDR08				0x058 0x248 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_FLEXPWM4_PWM3_A			0x058 0x248 0x4A0 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_LPUART4_CTS_B			0x058 0x248 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_FLEXCAN1_TX				0x058 0x248 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_TMR3_TIMER2				0x058 0x248 0x584 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_GPIO4_IO17				0x058 0x248 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_18_SEMC_ADDR09				0x05C 0x24C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_FLEXPWM4_PWM3_B			0x05C 0x24C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_LPUART4_RTS_B			0x05C 0x24C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_FLEXCAN1_RX				0x05C 0x24C 0x44C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_18_TMR3_TIMER3				0x05C 0x24C 0x588 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_GPIO4_IO18				0x05C 0x24C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_SNVS_VIO_5_CTL			0x05C 0x24C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_19_SEMC_ADDR11				0x060 0x250 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_FLEXPWM2_PWM3_A			0x060 0x250 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_LPUART4_TXD				0x060 0x250 0x544 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_19_ENET_RX_DATA01			0x060 0x250 0x438 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_TMR2_TIMER0				0x060 0x250 0x56C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_GPIO4_IO19				0x060 0x250 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_SNVS_VIO_5				0x060 0x250 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_20_SEMC_ADDR12				0x064 0x254 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_20_FLEXPWM2_PWM3_B			0x064 0x254 0x484 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_20_LPUART4_RXD				0x064 0x254 0x540 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_20_ENET_RX_DATA00			0x064 0x254 0x434 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_20_TMR2_TIMER0				0x064 0x254 0x570 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_20_GPIO4_IO20				0x064 0x254 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_21_SEMC_BA0				0x068 0x258 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_FLEXPWM3_PWM3_A			0x068 0x258 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_LPI2C3_SDA				0x068 0x258 0x4E0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_ENET_TX_DATA01			0x068 0x258 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_TMR2_TIMER2				0x068 0x258 0x574 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_GPIO4_IO21				0x068 0x258 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_22_SEMC_BA1				0x06C 0x25C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_FLEXPWM3_PWM3_B			0x06C 0x25C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_LPI2C3_SCL				0x06C 0x25C 0x4DC 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_ENET_TX_DATA00			0x06C 0x25C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_TMR2_TIMER3				0x06C 0x25C 0x578 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_GPIO4_IO22				0x06C 0x25C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_23_SEMC_ADDR10				0x070 0x260 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_FLEXPWM1_PWM0_A			0x070 0x260 0x458 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_LPUART5_TXD				0x070 0x260 0x54C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_ENET_RX_EN				0x070 0x260 0x43C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_GPT1_CAPTURE2			0x070 0x260 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_GPIO4_IO23				0x070 0x260 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_24_SEMC_CAS				0x074 0x264 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_FLEXPWM1_PWM0_B			0x074 0x264 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_LPUART5_RXD				0x074 0x264 0x548 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_ENET_TX_EN				0x074 0x264 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_GPT1_CAPTURE1			0x074 0x264 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_GPIO4_IO24				0x074 0x264 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_25_SEMC_RAS				0x078 0x268 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_FLEXPWM1_PWM1_A			0x078 0x268 0x45C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_LPUART6_TXD				0x078 0x268 0x554 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_ENET_TX_CLK				0x078 0x268 0x448 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_ENET_REF_CLK			0x078 0x268 0x42C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_GPIO4_IO25				0x078 0x268 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_26_SEMC_CLK				0x07C 0x26C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_FLEXPWM1_PWM1_B			0x07C 0x26C 0x46C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_LPUART6_RXD				0x07C 0x26C 0x550 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_ENET_RX_ER				0x07C 0x26C 0x440 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_FLEXIO1_D12				0x07C 0x26C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_GPIO4_IO26				0x07C 0x26C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_27_SEMC_CKE				0x080 0x270 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_FLEXPWM1_PWM2_A			0x080 0x270 0x460 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_LPUART5_RTS_B			0x080 0x270 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_LPSPI1_SCK				0x080 0x270 0x4F0 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_FLEXIO1_D13				0x080 0x270 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_GPIO4_IO27				0x080 0x270 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_28_SEMC_WE				0x084 0x274 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_FLEXPWM1_PWM2_B			0x084 0x274 0x470 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_LPUART5_CTS_B			0x084 0x274 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_LPSPI1_SDO				0x084 0x274 0x4F8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_FLEXIO1_D14				0x084 0x274 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_GPIO4_IO28				0x084 0x274 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_29_SEMC_CS0				0x088 0x278 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_FLEXPWM3_PWM0_A			0x088 0x278 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_LPUART6_RTS_B			0x088 0x278 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_LPSPI1_SDI				0x088 0x278 0x4F4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_FLEXIO1_D15				0x088 0x278 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_GPIO4_IO29				0x088 0x278 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_30_SEMC_DA08				0x08C 0x27C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_FLEXPWM3_PWM0_B			0x08C 0x27C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_LPUART6_CTS_B			0x08C 0x27C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_LPSPI1_PCS0				0x08C 0x27C 0x4EC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_30_CSI_DATA23				0x08C 0x27C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_GPIO4_IO30				0x08C 0x27C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_31_SEMC_DA09				0x090 0x280 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_FLEXPWM3_PWM1_A			0x090 0x280 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_LPUART7_TXD				0x090 0x280 0x55C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_31_LPSPI1_PCS1				0x090 0x280 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_CSI_DATA22				0x090 0x280 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_GPIO4_IO31				0x090 0x280 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_32_SEMC_DA10				0x094 0x284 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_32_FLEXPWM3_PWM1_B			0x094 0x284 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_32_LPUART7_RXD				0x094 0x284 0x558 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_32_CCM_PMIC_READY			0x094 0x284 0x3FC 0x3 0x4
+#define MXRT1050_IOMUXC_GPIO_EMC_32_CSI_DATA21				0x094 0x284 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_32_GPIO3_IO18				0x094 0x284 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_33_SEMC_DA11				0x098 0x288 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_FLEXPWM3_PWM2_A			0x098 0x288 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_USDHC1_RESET_B			0x098 0x288 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_SAI3_RX_DATA			0x098 0x288 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_CSI_DATA20				0x098 0x288 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_GPIO3_IO19				0x098 0x288 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_34_SEMC_DA12				0x09C 0x28C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_FLEXPWM3_PWM2_B			0x09C 0x28C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_USDHC1_VSELECT			0x09C 0x28C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_SAI3_RX_SYNC			0x09C 0x28C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_CSI_DATA19				0x09C 0x28C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_GPIO3_IO20				0x09C 0x28C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_35_SEMC_DA13				0x0A0 0x290 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_XBAR_INOUT18			0x0A0 0x290 0x630 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_GPT1_COMPARE1			0x0A0 0x290 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_SAI3_RX_BCLK			0x0A0 0x290 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_CSI_DATA18				0x0A0 0x290 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_GPIO3_IO21				0x0A0 0x290 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_USDHC1_CD_B				0x0A0 0x290 0x5D4 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_36_SEMC_DA14				0x0A4 0x294 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_XBAR_INOUT22			0x0A4 0x294 0x638 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_GPT1_COMPARE2			0x0A4 0x294 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_SAI3_TX_DATA			0x0A4 0x294 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_CSI_DATA17				0x0A4 0x294 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_GPIO3_IO22				0x0A4 0x294 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_USDHC1_WP				0x0A4 0x294 0x5D8 0x6 0x1
+
+#define MXRT1050_IOMUXC_GPIO_EMC_37_SEMC_DA15				0x0A8 0x298 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_XBAR_INOUT23			0x0A8 0x298 0x63C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_GPT1_COMPARE3			0x0A8 0x298 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_SAI3_MCLK				0x0A8 0x298 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_CSI_DATA16				0x0A8 0x298 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_GPIO3_IO23				0x0A8 0x298 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_USDHC2_WP				0x0A8 0x298 0x608 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_38_SEMC_DM01				0x0AC 0x29C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_FLEXPWM1_PWM3_A			0x0AC 0x29C 0x454 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_38_LPUART8_TXD				0x0AC 0x29C 0x564 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_38_SAI3_TX_BCLK			0x0AC 0x29C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_CSI_FIELD				0x0AC 0x29C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_GPIO3_IO24				0x0AC 0x29C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_USDHC2_VSELECT			0x0AC 0x29C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_39_SEMC_DQS				0x0B0 0x2A0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_FLEXPWM1_PWM3_B			0x0B0 0x2A0 0x464 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_39_LPUART8_RXD				0x0B0 0x2A0 0x560 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_39_SAI3_TX_SYNC			0x0B0 0x2A0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_WDOG1_B				0x0B0 0x2A0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_GPIO3_IO25				0x0B0 0x2A0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_USDHC2_CD_B				0x0B0 0x2A0 0x5E0 0x6 0x1
+
+#define MXRT1050_IOMUXC_GPIO_EMC_40_SEMC_RDY				0x0B4 0x2A4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_GPT2_CAPTURE2			0x0B4 0x2A4 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_LPSPI1_PCS2				0x0B4 0x2A4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_USB_OTG2_OC				0x0B4 0x2A4 0x5CC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_40_ENET_MDC				0x0B4 0x2A4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_GPIO3_IO26				0x0B4 0x2A4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_USDHC2_RESET_B			0x0B4 0x2A4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_41_SEMC_CSX0				0x0B8 0x2A8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_GPT2_CAPTURE1			0x0B8 0x2A8 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_LPSPI1_PCS3				0x0B8 0x2A8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_USB_OTG2_PWR			0x0B8 0x2A8 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_ENET_MDIO				0x0B8 0x2A8 0x430 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_41_GPIO3_IO27				0x0B8 0x2A8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_USDHC2_VSELECT			0x0B8 0x2A8 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_FLEXPWM2_PWM3_A			0x0BC 0x2AC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_XBAR_INOUT14			0x0BC 0x2AC 0x644 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_REF_CLK_32K			0x0BC 0x2AC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_USB_OTG2_ID			0x0BC 0x2AC 0x3F8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_LPI2C1_SCLS			0x0BC 0x2AC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_GPIO1_IO00			0x0BC 0x2AC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_USDHC1_RESET_B			0x0BC 0x2AC 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_LPSPI3_SCK			0x0BC 0x2AC 0x510 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_FLEXPWM2_PWM3_B			0x0C0 0x2B0 0x484 0x0 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_XBAR_INOUT15			0x0C0 0x2B0 0x648 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_REF_CLK_24M			0x0C0 0x2B0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_USB_OTG1_ID			0x0C0 0x2B0 0x3F4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_LPI2C1_SDAS			0x0C0 0x2B0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_GPIO1_IO01			0x0C0 0x2B0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_EWM_OUT_B				0x0C0 0x2B0 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_LPSPI3_SDO			0x0C0 0x2B0 0x518 0x7 0x1
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_FLEXCAN2_TX			0x0C4 0x2B4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_XBAR_INOUT16			0x0C4 0x2B4 0x64C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_LPUART6_TXD			0x0C4 0x2B4 0x554 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_USB_OTG1_PWR			0x0C4 0x2B4 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_FLEXPWM1_PWM0_X			0x0C4 0x2B4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_GPIO1_IO02			0x0C4 0x2B4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_LPI2C1_HREQ			0x0C4 0x2B4 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_LPSPI3_SDI			0x0C4 0x2B4 0x514 0x7 0x1
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_FLEXCAN2_RX			0x0C8 0x2B8 0x450 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_XBAR_INOUT17			0x0C8 0x2B8 0x62C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_LPUART6_RXD			0x0C8 0x2B8 0x550 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_USB_OTG1_OC			0x0C8 0x2B8 0x5D0 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_FLEXPWM1_PWM1_X			0x0C8 0x2B8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_GPIO1_IO03			0x0C8 0x2B8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_REF_CLK_24M			0x0C8 0x2B8 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_LPSPI3_PCS0			0x0C8 0x2B8 0x50C 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_SRC_BOOT_MODE00			0x0CC 0x2BC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_MQS_RIGHT				0x0CC 0x2BC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_ENET_TX_DATA03			0x0CC 0x2BC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_SAI2_TX_SYNC			0x0CC 0x2BC 0x5C4 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_CSI_DATA09			0x0CC 0x2BC 0x41C 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_GPIO1_IO04			0x0CC 0x2BC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_PIT_TRIGGER00			0x0CC 0x2BC 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_LPSPI3_PCS1			0x0CC 0x2BC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_SRC_BOOT_MODE01			0x0D0 0x2C0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_MQS_LEFT				0x0D0 0x2C0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_ENET_TX_DATA02			0x0D0 0x2C0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_SAI2_TX_BCLK			0x0D0 0x2C0 0x5C0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_CSI_DATA08			0x0D0 0x2C0 0x418 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_GPIO1_IO05			0x0D0 0x2C0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_XBAR_INOUT17			0x0D0 0x2C0 0x62C 0x6 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_LPSPI3_PCS2			0x0D0 0x2C0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_JTAG_TMS				0x0D4 0x2C4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_GPT2_COMPARE1			0x0D4 0x2C4 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_ENET_RX_CLK			0x0D4 0x2C4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_SAI2_RX_BCLK			0x0D4 0x2C4 0x5B4 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_CSI_DATA07			0x0D4 0x2C4 0x414 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_GPIO1_IO06			0x0D4 0x2C4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_XBAR_INOUT18			0x0D4 0x2C4 0x630 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_LPSPI3_PCS3			0x0D4 0x2C4 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_JTAG_TCK				0x0D8 0x2C8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_GPT2_COMPARE2			0x0D8 0x2C8 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_ENET_TX_ER			0x0D8 0x2C8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_SAI2_RX_SYNC			0x0D8 0x2C8 0x5BC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_CSI_DATA06			0x0D8 0x2C8 0x410 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_GPIO1_IO07			0x0D8 0x2C8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_XBAR_INOUT19			0x0D8 0x2C8 0x654 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_ENET_1588_EVENT3_OUT		0x0D8 0x2C8 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_JTAG_MOD				0x0DC 0x2CC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_GPT2_COMPARE3			0x0DC 0x2CC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_ENET_RX_DATA03			0x0DC 0x2CC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_SAI2_RX_DATA			0x0DC 0x2CC 0x5B8 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_CSI_DATA05			0x0DC 0x2CC 0x40C 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_GPIO1_IO08			0x0DC 0x2CC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_XBAR_INOUT20			0x0DC 0x2CC 0x634 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_ENET_1588_EVENT3_IN		0x0DC 0x2CC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_JTAG_TDI				0x0E0 0x2D0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_FLEXPWM2_PWM3_A			0x0E0 0x2D0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_ENET_RX_DATA02			0x0E0 0x2D0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_SAI2_TX_DATA			0x0E0 0x2D0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_CSI_DATA04			0x0E0 0x2D0 0x408 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_GPIO1_IO09			0x0E0 0x2D0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_XBAR_INOUT21			0x0E0 0x2D0 0x658 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_GPT2_CLK				0x0E0 0x2D0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_JTAG_TDO				0x0E4 0x2D4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_FLEXPWM1_PWM3_A			0x0E4 0x2D4 0x454 0x1 0x3
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_ENET_CRS				0x0E4 0x2D4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_SAI2_MCLK				0x0E4 0x2D4 0x5B0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_CSI_DATA03			0x0E4 0x2D4 0x404 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_GPIO1_IO10			0x0E4 0x2D4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_XBAR_INOUT22			0x0E4 0x2D4 0x638 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_ENET_1588_EVENT0_OUT		0x0E4 0x2D4 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_JTAG_TRSTB			0x0E8 0x2D8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_FLEXPWM1_PWM3_B			0x0E8 0x2D8 0x464 0x1 0x3
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_ENET_COL				0x0E8 0x2D8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_WDOG1_B				0x0E8 0x2D8 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_CSI_DATA02			0x0E8 0x2D8 0x400 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_GPIO1_IO11			0x0E8 0x2D8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_XBAR_INOUT23			0x0E8 0x2D8 0x63C 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_ENET_1588_EVENT0_IN		0x0E8 0x2D8 0x444 0x7 0x1
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_LPI2C4_SCL			0x0EC 0x2DC 0x4E4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_CCM_PMIC_READY			0x0EC 0x2DC 0x3FC 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD			0x0EC 0x2DC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_WDOG2_B				0x0EC 0x2DC 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_FLEXPWM1_PWM2_X			0x0EC 0x2DC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_GPIO1_IO12			0x0EC 0x2DC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_ENET_1588_EVENT1_OUT		0x0EC 0x2DC 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_NMI				0x0EC 0x2DC 0x568 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_LPI2C4_SDA			0x0F0 0x2E0 0x4E8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_GPT1_CLK				0x0F0 0x2E0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_LPUART1_RXD			0x0F0 0x2E0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_EWM_OUT_B				0x0F0 0x2E0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_FLEXPWM1_PWM3_X			0x0F0 0x2E0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_GPIO1_IO13			0x0F0 0x2E0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_ENET_1588_EVENT1_IN		0x0F0 0x2E0 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_REF_CLK_24M			0x0F0 0x2E0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_USB_OTG2_OC			0x0F4 0x2E4 0x5CC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_XBAR_INOUT24			0x0F4 0x2E4 0x640 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_LPUART1_CTS_B			0x0F4 0x2E4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_ENET_1588_EVENT0_OUT		0x0F4 0x2E4 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_CSI_VSYNC				0x0F4 0x2E4 0x428 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_GPIO1_IO14			0x0F4 0x2E4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_FLEXCAN2_TX			0x0F4 0x2E4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_USB_OTG2_PWR			0x0F8 0x2E8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_XBAR_INOUT25			0x0F8 0x2E8 0x650 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_LPUART1_RTS_B			0x0F8 0x2E8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_ENET_1588_EVENT0_IN		0x0F8 0x2E8 0x444 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_CSI_HSYNC				0x0F8 0x2E8 0x420 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_GPIO1_IO15			0x0F8 0x2E8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_FLEXCAN2_RX			0x0F8 0x2E8 0x450 0x6 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_WDOG1_WDOG_RST_B_DEB		0x0F8 0x2E8 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_USB_OTG2_ID			0x0FC 0x2EC 0x3F8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_TMR3_TIMER0			0x0FC 0x2EC 0x57C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_LPUART2_CTS_B			0x0FC 0x2EC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL			0x0FC 0x2EC 0x4CC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_WDOG1_B				0x0FC 0x2EC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_GPIO1_IO16			0x0FC 0x2EC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_USDHC1_WP				0x0FC 0x2EC 0x5D8 0x6 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_KPP_ROW07				0x0FC 0x2EC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_USB_OTG1_PWR			0x100 0x2F0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_TMR3_TIMER1			0x100 0x2F0 0x580 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_LPUART2_RTS_B			0x100 0x2F0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA			0x100 0x2F0 0x4D0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_CCM_PMIC_READY			0x100 0x2F0 0x3FC 0x4 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_GPIO1_IO17			0x100 0x2F0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_USDHC1_VSELECT			0x100 0x2F0 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_KPP_COL07				0x100 0x2F0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_USB_OTG1_ID			0x104 0x2F4 0x3F4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_TMR3_TIMER2			0x104 0x2F4 0x584 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_LPUART2_TXD			0x104 0x2F4 0x530 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_SPDIF_OUT				0x104 0x2F4 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_ENET_1588_EVENT2_OUT		0x104 0x2F4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_GPIO1_IO18			0x104 0x2F4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_USDHC1_CD_B			0x104 0x2F4 0x5D4 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_KPP_ROW06				0x104 0x2F4 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_USB_OTG1_OC			0x108 0x2F8 0x5D0 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_TMR3_TIMER3			0x108 0x2F8 0x588 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_LPUART2_RXD			0x108 0x2F8 0x52C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_SPDIF_IN				0x108 0x2F8 0x5C8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_ENET_1588_EVENT2_IN		0x108 0x2F8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_GPIO1_IO19			0x108 0x2F8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_USDHC2_CD_B			0x108 0x2F8 0x5E0 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_KPP_COL06				0x108 0x2F8 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_FLEXSPI_B_DATA3			0x10C 0x2FC 0x4C4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_ENET_MDC				0x10C 0x2FC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_LPUART3_CTS_B			0x10C 0x2FC 0x534 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_SPDIF_SR_CLK			0x10C 0x2FC 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_CSI_PIXCLK			0x10C 0x2FC 0x424 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_GPIO1_IO20			0x10C 0x2FC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_USDHC2_DATA0			0x10C 0x2FC 0x5E8 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_KPP_ROW05				0x10C 0x2FC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_FLEXSPI_B_DATA2			0x110 0x300 0x4C0 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_ENET_MDIO				0x110 0x300 0x430 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_LPUART3_RTS_B			0x110 0x300 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_SPDIF_OUT				0x110 0x300 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_CSI_MCLK				0x110 0x300 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_GPIO1_IO21			0x110 0x300 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_USDHC2_DATA1			0x110 0x300 0x5EC 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_KPP_COL05				0x110 0x300 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_FLEXSPI_B_DATA1			0x114 0x304 0x4BC 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_LPI2C3_SDA			0x114 0x304 0x4E0 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_LPUART3_TXD			0x114 0x304 0x53C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_SPDIF_LOCK			0x114 0x304 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_CSI_VSYNC				0x114 0x304 0x428 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_GPIO1_IO22			0x114 0x304 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_USDHC2_DATA2			0x114 0x304 0x5F0 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_KPP_ROW04				0x114 0x304 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_FLEXSPI_B_DATA0			0x118 0x308 0x4B8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_LPI2C3_SCL			0x118 0x308 0x4DC 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_LPUART3_RXD			0x118 0x308 0x538 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_SPDIF_EXT_CLK			0x118 0x308 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_CSI_HSYNC				0x118 0x308 0x420 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_GPIO1_IO23			0x118 0x308 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_USDHC2_DATA3			0x118 0x308 0x5F4 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_KPP_COL04				0x118 0x308 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_FLEXSPI_A_SS1_B			0x11C 0x30C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_FLEXPWM4_PWM0_A			0x11C 0x30C 0x494 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_FLEXCAN1_TX			0x11C 0x30C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_CCM_PMIC_READY			0x11C 0x30C 0x3FC 0x3 0x3
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_CSI_DATA09			0x11C 0x30C 0x41C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_GPIO1_IO24			0x11C 0x30C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_USDHC2_CMD			0x11C 0x30C 0x5E4 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_KPP_ROW03				0x11C 0x30C 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_FLEXSPI_A_DQS			0x120 0x310 0x4A4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_FLEXPWM4_PWM1_A			0x120 0x310 0x498 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_FLEXCAN1_RX			0x120 0x310 0x44C 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_SAI1_MCLK				0x120 0x310 0x58C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_CSI_DATA08			0x120 0x310 0x418 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_GPIO1_IO25			0x120 0x310 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_USDHC2_CLK			0x120 0x310 0x5DC 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_KPP_COL03				0x120 0x310 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_FLEXSPI_A_DATA3			0x124 0x314 0x4B4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_WDOG1_B				0x124 0x314 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_LPUART8_TXD			0x124 0x314 0x564 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_SAI1_RX_SYNC			0x124 0x314 0x5A4 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_CSI_DATA07			0x124 0x314 0x414 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_GPIO1_IO26			0x124 0x314 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_USDHC2_WP				0x124 0x314 0x608 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_KPP_ROW02				0x124 0x314 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_FLEXSPI_A_DATA2			0x128 0x318 0x4B0 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_EWM_OUT_B				0x128 0x318 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_LPUART8_RXD			0x128 0x318 0x560 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_SAI1_RX_BCLK			0x128 0x318 0x590 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_CSI_DATA06			0x128 0x318 0x410 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_GPIO1_IO27			0x128 0x318 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_USDHC2_RESET_B			0x128 0x318 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_KPP_COL02				0x128 0x318 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_FLEXSPI_A_DATA1			0x12C 0x31C 0x4AC 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_ACMP1_OUT				0x12C 0x31C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_LPSPI3_PCS0			0x12C 0x31C 0x50C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_SAI1_RX_DATA00			0x12C 0x31C 0x594 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_CSI_DATA05			0x12C 0x31C 0x40C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_GPIO1_IO28			0x12C 0x31C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_USDHC2_DATA4			0x12C 0x31C 0x5F8 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_KPP_ROW01				0x12C 0x31C 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_FLEXSPI_A_DATA0			0x130 0x320 0x4A8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_ACMP2_OUT				0x130 0x320 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_LPSPI3_SDI			0x130 0x320 0x514 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_SAI1_TX_DATA00			0x130 0x320 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_CSI_DATA04			0x130 0x320 0x408 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_GPIO1_IO29			0x130 0x320 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_USDHC2_DATA5			0x130 0x320 0x5FC 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_KPP_COL01				0x130 0x320 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_FLEXSPI_A_SCLK			0x134 0x324 0x4C8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_ACMP3_OUT				0x134 0x324 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_LPSPI3_SDO			0x134 0x324 0x518 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_SAI1_TX_BCLK			0x134 0x324 0x5A8 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_CSI_DATA03			0x134 0x324 0x404 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_GPIO1_IO30			0x134 0x324 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_USDHC2_DATA6			0x134 0x324 0x600 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_KPP_ROW00				0x134 0x324 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_FLEXSPI_A_SS0_B			0x138 0x328 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_ACMP4_OUT				0x138 0x328 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_LPSPI3_SCK			0x138 0x328 0x510 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_SAI1_TX_SYNC			0x138 0x328 0x5AC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_CSI_DATA02			0x138 0x328 0x400 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_GPIO1_IO31			0x138 0x328 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_USDHC2_DATA7			0x138 0x328 0x604 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_KPP_COL00				0x138 0x328 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_00_LCD_CLK				0x13C 0x32C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_TMR1_TIMER0				0x13C 0x32C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_MQS_RIGHT				0x13C 0x32C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_LPSPI4_PCS0				0x13C 0x32C 0x51C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_FLEXIO2_D00				0x13C 0x32C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_GPIO2_IO00				0x13C 0x32C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_SEMC_CSX1				0x13C 0x32C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_01_LCD_ENABLE				0x140 0x330 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_TMR1_TIMER1				0x140 0x330 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_MQS_LEFT				0x140 0x330 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_LPSPI4_SDI				0x140 0x330 0x524 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_FLEXIO2_D01				0x140 0x330 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_GPIO2_IO01				0x140 0x330 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_SEMC_CSX2				0x140 0x330 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_02_LCD_HSYNC				0x144 0x334 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_TMR1_TIMER2				0x144 0x334 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_FLEXCAN1_TX				0x144 0x334 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_LPSPI4_SDO				0x144 0x334 0x528 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_FLEXIO2_D02				0x144 0x334 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_GPIO2_IO02				0x144 0x334 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_SEMC_CSX3				0x144 0x334 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_03_LCD_VSYNC				0x148 0x338 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_TMR2_TIMER0				0x148 0x338 0x56C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_03_FLEXCAN1_RX				0x148 0x338 0x44C 0x2 0x3
+#define MXRT1050_IOMUXC_GPIO_B0_03_LPSPI4_SCK				0x148 0x338 0x520 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_FLEXIO2_D03				0x148 0x338 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_GPIO2_IO03				0x148 0x338 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_WDOG2_RESET_B_DEB			0x148 0x338 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_04_LCD_DATA00				0x14C 0x33C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_TMR2_TIMER1				0x14C 0x33C 0x570 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_04_LPI2C2_SCL				0x14C 0x33C 0x4D4 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_04_ARM_TRACE00				0x14C 0x33C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_FLEXIO2_D04				0x14C 0x33C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_GPIO2_IO04				0x14C 0x33C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_SRC_BT_CFG00				0x14C 0x33C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_05_LCD_DATA01				0x150 0x340 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_TMR2_TIMER2				0x150 0x340 0x574 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_05_LPI2C2_SDA				0x150 0x340 0x4D8 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_05_ARM_TRACE01				0x150 0x340 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_FLEXIO2_D05				0x150 0x340 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_GPIO2_IO05				0x150 0x340 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_SRC_BT_CFG01				0x150 0x340 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_06_LCD_DATA02				0x154 0x344 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_TMR3_TIMER0				0x154 0x344 0x57C 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_06_FLEXPWM2_PWM0_A			0x154 0x344 0x478 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_06_ARM_TRACE02				0x154 0x344 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_FLEXIO2_D06				0x154 0x344 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_GPIO2_IO06				0x154 0x344 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_SRC_BT_CFG02				0x154 0x344 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_07_LCD_DATA03				0x158 0x348 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_TMR3_TIMER1				0x158 0x348 0x580 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_07_FLEXPWM2_PWM0_B			0x158 0x348 0x488 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_07_ARM_TRACE03				0x158 0x348 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_FLEXIO2_D07				0x158 0x348 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_GPIO2_IO07				0x158 0x348 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_SRC_BT_CFG03				0x158 0x348 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_08_LCD_DATA04				0x15C 0x34C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_08_TMR3_TIMER2				0x15C 0x34C 0x584 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_08_FLEXPWM2_PWM1_A			0x15C 0x34C 0x47C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_08_LPUART3_TXD				0x15C 0x34C 0x53C 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_08_FLEXIO2_D08				0x15C 0x34C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_08_GPIO2_IO08				0x15C 0x34C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_08_SRC_BT_CFG04				0x15C 0x34C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_09_LCD_DATA05				0x160 0x350 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_TMR4_TIMER0				0x160 0x350 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_FLEXPWM2_PWM1_B			0x160 0x350 0x48C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_09_LPUART3_RXD				0x160 0x350 0x538 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_09_FLEXIO2_D09				0x160 0x350 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_GPIO2_IO09				0x160 0x350 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_SRC_BT_CFG05				0x160 0x350 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_10_LCD_DATA06				0x164 0x354 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_TMR4_TIMER1				0x164 0x354 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_FLEXPWM2_PWM2_A			0x164 0x354 0x480 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_10_SAI1_TX_DATA03			0x164 0x354 0x598 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_10_FLEXIO2_D10				0x164 0x354 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_GPIO2_IO10				0x164 0x354 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_SRC_BT_CFG06				0x164 0x354 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_11_LCD_DATA07				0x168 0x358 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_TMR4_TIMER2				0x168 0x358 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_FLEXPWM2_PWM2_B			0x168 0x358 0x490 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_11_SAI1_TX_DATA02			0x168 0x358 0x59C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_11_FLEXIO2_D11				0x168 0x358 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_GPIO2_IO11				0x168 0x358 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_SRC_BT_CFG07				0x168 0x358 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_12_LCD_DATA08				0x16C 0x35C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_XBAR_INOUT10				0x16C 0x35C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_ARM_TRACE_CLK			0x16C 0x35C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_SAI1_TX_DATA01			0x16C 0x35C 0x5A0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_12_FLEXIO2_D12				0x16C 0x35C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_GPIO2_IO12				0x16C 0x35C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_SRC_BT_CFG08				0x16C 0x35C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_13_LCD_DATA09				0x170 0x360 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_XBAR_INOUT11				0x170 0x360 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_ARM_TRACE_SWO			0x170 0x360 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_SAI1_MCLK				0x170 0x360 0x58C 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_13_FLEXIO2_D13				0x170 0x360 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_GPIO2_IO13				0x170 0x360 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_SRC_BT_CFG09				0x170 0x360 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_14_LCD_DATA10				0x174 0x364 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_XBAR_INOUT12				0x174 0x364 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_ARM_CM7_TXEV				0x174 0x364 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_SAI1_RX_SYNC				0x174 0x364 0x5A4 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_14_FLEXIO2_D14				0x174 0x364 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_GPIO2_IO14				0x174 0x364 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_SRC_BT_CFG10				0x174 0x364 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_15_LCD_DATA11				0x178 0x368 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_XBAR_INOUT13				0x178 0x368 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_ARM_CM7_RXEV				0x178 0x368 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_SAI1_RX_BCLK				0x178 0x368 0x590 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_15_FLEXIO2_D15				0x178 0x368 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_GPIO2_IO15				0x178 0x368 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_SRC_BT_CFG11				0x178 0x368 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_00_LCD_DATA12				0x17C 0x36C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_00_XBAR_INOUT14				0x17C 0x36C 0x644 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_00_LPUART4_TXD				0x17C 0x36C 0x544 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_00_SAI1_RX_DATA00			0x17C 0x36C 0x594 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_00_FLEXIO2_D16				0x17C 0x36C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_00_GPIO2_IO16				0x17C 0x36C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_00_FLEXPWM1_PWM3_A			0x17C 0x36C 0x454 0x6 0x4
+
+#define MXRT1050_IOMUXC_GPIO_B1_01_LCD_DATA13				0x180 0x370 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_XBAR_INOUT15				0x180 0x370 0x648 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_01_LPUART4_RXD				0x180 0x370 0x540 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_01_SAI1_TX_DATA00			0x180 0x370 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_FLEXIO2_D17				0x180 0x370 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_GPIO2_IO17				0x180 0x370 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_FLEXPWM1_PWM3_B			0x180 0x370 0x464 0x6 0x4
+
+#define MXRT1050_IOMUXC_GPIO_B1_02_LCD_DATA14				0x184 0x374 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_XBAR_INOUT16				0x184 0x374 0x64C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_02_LPSPI4_PCS2				0x184 0x374 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_SAI1_TX_BCLK				0x184 0x374 0x5A8 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_02_FLEXIO2_D18				0x184 0x374 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_GPIO2_IO18				0x184 0x374 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_FLEXPWM2_PWM3_A			0x184 0x374 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_03_LCD_DATA15				0x188 0x378 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_XBAR_INOUT17				0x188 0x378 0x62C 0x1 0x3
+#define MXRT1050_IOMUXC_GPIO_B1_03_LPSPI4_PCS1				0x188 0x378 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_SAI1_TX_SYNC				0x188 0x378 0x5AC 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_03_FLEXIO2_D19				0x188 0x378 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_GPIO2_IO19				0x188 0x378 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_FLEXPWM2_PWM3_B			0x188 0x378 0x484 0x6 0x3
+
+#define MXRT1050_IOMUXC_GPIO_B1_04_LCD_DATA16				0x18C 0x37C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_04_LPSPI4_PCS0				0x18C 0x37C 0x51C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_04_CSI_DATA15				0x18C 0x37C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_04_ENET_RX_DATA00			0x18C 0x37C 0x434 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_04_FLEXIO2_D20				0x18C 0x37C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_04_GPIO2_IO20				0x18C 0x37C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_05_LCD_DATA17				0x190 0x380 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_05_LPSPI4_SDI				0x190 0x380 0x524 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_05_CSI_DATA14				0x190 0x380 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_05_ENET_RX_DATA01			0x190 0x380 0x438 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_05_FLEXIO2_D21				0x190 0x380 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_05_GPIO2_IO21				0x190 0x380 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_06_LCD_DATA18				0x194 0x384 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_06_LPSPI4_SDO				0x194 0x384 0x528 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_06_CSI_DATA13				0x194 0x384 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_06_ENET_RX_EN				0x194 0x384 0x43C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_06_FLEXIO2_D22				0x194 0x384 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_06_GPIO2_IO22				0x194 0x384 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_07_LCD_DATA19				0x198 0x388 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_LPSPI4_SCK				0x198 0x388 0x520 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_07_CSI_DATA12				0x198 0x388 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_ENET_TX_DATA00			0x198 0x388 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_FLEXIO2_D23				0x198 0x388 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_GPIO2_IO23				0x198 0x388 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_08_LCD_DATA20				0x19C 0x38C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_TMR1_TIMER3				0x19C 0x38C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_CSI_DATA11				0x19C 0x38C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_ENET_TX_DATA01			0x19C 0x38C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_FLEXIO2_D24				0x19C 0x38C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_GPIO2_IO24				0x19C 0x38C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_FLEXCAN2_TX				0x19C 0x38C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_09_LCD_DATA21				0x1A0 0x390 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_TMR2_TIMER3				0x1A0 0x390 0x578 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_09_CSI_DATA10				0x1A0 0x390 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_ENET_TX_EN				0x1A0 0x390 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_FLEXIO2_D25				0x1A0 0x390 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_GPIO2_IO25				0x1A0 0x390 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_FLEXCAN2_RX				0x1A0 0x390 0x450 0x6 0x3
+
+#define MXRT1050_IOMUXC_GPIO_B1_10_LCD_DATA22				0x1A4 0x394 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_TMR3_TIMER3				0x1A4 0x394 0x588 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_10_CSI_DATA00				0x1A4 0x394 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_ENET_TX_CLK				0x1A4 0x394 0x448 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_10_FLEXIO2_D26				0x1A4 0x394 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_GPIO2_IO26				0x1A4 0x394 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_ENET_REF_CLK				0x1A4 0x394 0x42C 0x6 0x1
+
+#define MXRT1050_IOMUXC_GPIO_B1_11_LCD_DATA23				0x1A8 0x398 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_TMR4_TIMER3				0x1A8 0x398 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_CSI_DATA01				0x1A8 0x398 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_ENET_RX_ER				0x1A8 0x398 0x440 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_11_FLEXIO2_D27				0x1A8 0x398 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_GPIO2_IO27				0x1A8 0x398 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_LPSPI4_PCS3				0x1A8 0x398 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_12_LPUART5_TXD				0x1AC 0x39C 0x54C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_12_CSI_PIXCLK				0x1AC 0x39C 0x424 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_12_ENET_1588_EVENT0_IN			0x1AC 0x39C 0x444 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_12_FLEXIO2_D28				0x1AC 0x39C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_12_GPIO2_IO28				0x1AC 0x39C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_12_USDHC1_CD_B				0x1AC 0x39C 0x5D4 0x6 0x2
+
+#define MXRT1050_IOMUXC_GPIO_B1_13_WDOG1_B				0x1B0 0x3A0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_LPUART5_RXD				0x1B0 0x3A0 0x548 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_13_CSI_VSYNC				0x1B0 0x3A0 0x428 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_13_ENET_1588_EVENT0_OUT			0x1B0 0x3A0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_FLEXIO2_D29				0x1B0 0x3A0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_GPIO2_IO29				0x1B0 0x3A0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_USDHC1_WP				0x1B0 0x3A0 0x5D8 0x6 0x3
+
+#define MXRT1050_IOMUXC_GPIO_B1_14_ENET_MDC				0x1B4 0x3A4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_14_FLEXPWM4_PWM2_A			0x1B4 0x3A4 0x49C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_14_CSI_HSYNC				0x1B4 0x3A4 0x420 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_14_XBAR_INOUT02				0x1B4 0x3A4 0x60C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_14_FLEXIO2_D30				0x1B4 0x3A4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_14_GPIO2_IO30				0x1B4 0x3A4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_14_USDHC1_VSELECT			0x1B4 0x3A4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_15_ENET_MDIO				0x1B8 0x3A8 0x430 0x0 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_15_FLEXPWM4_PWM3_A			0x1B8 0x3A8 0x4A0 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_15_CSI_MCLK				0x1B8 0x3A8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_15_XBAR_INOUT03				0x1B8 0x3A8 0x610 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_15_FLEXIO2_D31				0x1B8 0x3A8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_15_GPIO2_IO31				0x1B8 0x3A8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_15_USDHC1_RESET_B			0x1B8 0x3A8 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_USDHC1_CMD			0x1BC 0x3AC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_FLEXPWM1_PWM0_A			0x1BC 0x3AC 0x458 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_LPI2C3_SCL			0x1BC 0x3AC 0x4DC 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_XBAR_INOUT04			0x1BC 0x3AC 0x614 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_LPSPI1_SCK			0x1BC 0x3AC 0x4F0 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_GPIO3_IO12			0x1BC 0x3AC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_FLEXSPI_A_SS1_B			0x1BC 0x3AC 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_USDHC1_CLK			0x1C0 0x3B0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_FLEXPWM1_PWM0_B			0x1C0 0x3B0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_LPI2C3_SDA			0x1C0 0x3B0 0x4E0 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_XBAR_INOUT05			0x1C0 0x3B0 0x618 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_LPSPI1_PCS0			0x1C0 0x3B0 0x4EC 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_GPIO3_IO13			0x1C0 0x3B0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_FLEXSPI_B_SS1_B			0x1C0 0x3B0 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0			0x1C4 0x3B4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_FLEXPWM1_PWM1_A			0x1C4 0x3B4 0x45C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_LPUART8_CTS_B			0x1C4 0x3B4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_XBAR_INOUT06			0x1C4 0x3B4 0x61C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_LPSPI1_SDO			0x1C4 0x3B4 0x4F8 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_GPIO3_IO14			0x1C4 0x3B4 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1			0x1C8 0x3B8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_FLEXPWM1_PWM1_B			0x1C8 0x3B8 0x46C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_LPUART8_RTS_B			0x1C8 0x3B8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_XBAR_INOUT07			0x1C8 0x3B8 0x620 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_LPSPI1_SDI			0x1C8 0x3B8 0x4F4 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_GPIO3_IO15			0x1C8 0x3B8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2			0x1CC 0x3BC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_FLEXPWM1_PWM2_A			0x1CC 0x3BC 0x460 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_LPUART8_TXD			0x1CC 0x3BC 0x564 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_XBAR_INOUT08			0x1CC 0x3BC 0x624 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_FLEXSPI_B_SS0_B			0x1CC 0x3BC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_GPIO3_IO16			0x1CC 0x3BC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_CCM_CLKO1				0x1CC 0x3BC 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3			0x1D0 0x3C0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_FLEXPWM1_PWM2_B			0x1D0 0x3C0 0x470 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_LPUART8_RXD			0x1D0 0x3C0 0x560 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_XBAR_INOUT09			0x1D0 0x3C0 0x628 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_FLEXSPI_B_DQS			0x1D0 0x3C0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_GPIO3_IO17			0x1D0 0x3C0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_CCM_CLKO2				0x1D0 0x3C0 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_USDHC2_DATA3			0x1D4 0x3C4 0x5F4 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_FLEXSPI_B_DATA3			0x1D4 0x3C4 0x4C4 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_FLEXPWM1_PWM3_A			0x1D4 0x3C4 0x454 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_SAI1_TX_DATA03			0x1D4 0x3C4 0x598 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_LPUART4_TXD			0x1D4 0x3C4 0x544 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_GPIO3_IO00			0x1D4 0x3C4 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_USDHC2_DATA2			0x1D8 0x3C8 0x5F0 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_FLEXSPI_B_DATA2			0x1D8 0x3C8 0x4C0 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_FLEXPWM1_PWM3_B			0x1D8 0x3C8 0x464 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_SAI1_TX_DATA02			0x1D8 0x3C8 0x59C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_LPUART4_RXD			0x1D8 0x3C8 0x540 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_GPIO3_IO01			0x1D8 0x3C8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_USDHC2_DATA1			0x1DC 0x3CC 0x5EC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_FLEXSPI_B_DATA1			0x1DC 0x3CC 0x4BC 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_FLEXPWM2_PWM3_A			0x1DC 0x3CC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_SAI1_TX_DATA01			0x1DC 0x3CC 0x5A0 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_FLEXCAN1_TX			0x1DC 0x3CC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_GPIO3_IO02			0x1DC 0x3CC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_CCM_WAIT				0x1DC 0x3CC 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_USDHC2_DATA0			0x1E0 0x3D0 0x5E8 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_FLEXSPI_B_DATA0			0x1E0 0x3D0 0x4B8 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_FLEXPWM2_PWM3_B			0x1E0 0x3D0 0x484 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_SAI1_MCLK				0x1E0 0x3D0 0x58C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_FLEXCAN1_RX			0x1E0 0x3D0 0x44C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_GPIO3_IO03			0x1E0 0x3D0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_CCM_PMIC_READY			0x1E0 0x3D0 0x3FC 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_USDHC2_CLK			0x1E4 0x3D4 0x5DC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_FLEXSPI_B_SCLK			0x1E4 0x3D4 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_LPI2C1_SCL			0x1E4 0x3D4 0x4CC 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_SAI1_RX_SYNC			0x1E4 0x3D4 0x5A4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_FLEXCAN1_A_SS1_B			0x1E4 0x3D4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_GPIO3_IO04			0x1E4 0x3D4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_CCM_STOP				0x1E4 0x3D4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_USDHC2_CMD			0x1E8 0x3D8 0x5E4 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_FLEXSPI_A_DQS			0x1E8 0x3D8 0x4A4 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_LPI2C1_SDA			0x1E8 0x3D8 0x4D0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_SAI1_RX_BCLK			0x1E8 0x3D8 0x590 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_FLEXCAN1_B_SS0_B			0x1E8 0x3D8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_GPIO3_IO05			0x1E8 0x3D8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_USDHC2_RESET_B			0x1EC 0x3DC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_FLEXSPI_A_SS0_B			0x1EC 0x3DC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_LPUART7_CTS_B			0x1EC 0x3DC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_SAI1_RX_DATA00			0x1EC 0x3DC 0x594 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_LPSPI2_PCS0			0x1EC 0x3DC 0x4FC 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_GPIO3_IO06			0x1EC 0x3DC 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_SEMC_CSX1				0x1F0 0x3E0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_FLEXSPI_A_SCLK			0x1F0 0x3E0 0x4C8 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_LPUART7_RTS_B			0x1F0 0x3E0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_SAI1_TX_DATA00			0x1F0 0x3E0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_LPSPI2_SCK			0x1F0 0x3E0 0x500 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_GPIO3_IO07			0x1F0 0x3E0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_CCM_REF_EN_B			0x1F0 0x3E0 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_USDHC2_DATA4			0x1F4 0x3E4 0x5F8 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_FLEXSPI_A_DATA0			0x1F4 0x3E4 0x4A8 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_LPUART7_TXD			0x1F4 0x3E4 0x55C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_SAI1_TX_BLCK			0x1F4 0x3E4 0x5A8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_LPSPI2_SDO			0x1F4 0x3E4 0x508 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_GPIO3_IO08			0x1F4 0x3E4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_SEMC_CSX2				0x1F4 0x3E4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_USDHC2_DATA5			0x1F8 0x3E8 0x5FC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_FLEXSPI_A_DATA1			0x1F8 0x3E8 0x4AC 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_LPUART7_RXD			0x1F8 0x3E8 0x558 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_SAI1_TX_SYNC			0x1F8 0x3E8 0x5AC 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_LPSPI2_SDI			0x1F8 0x3E8 0x504 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_GPIO3_IO09			0x1F8 0x3E8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_USDHC2_DATA6			0x1FC 0x3EC 0x600 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_FLEXSPI_A_DATA2			0x1FC 0x3EC 0x4B0 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_LPUART2_RXD			0x1FC 0x3EC 0x52C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_LPI2C2_SDA			0x1FC 0x3EC 0x4D8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_LPSPI2_PCS2			0x1FC 0x3EC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_GPIO3_IO10			0x1FC 0x3EC 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_USDHC2_DATA7			0x200 0x3F0 0x604 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_FLEXSPI_A_DATA3			0x200 0x3F0 0x4B4 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_LPUART2_TXD			0x200 0x3F0 0x530 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_LPI2C2_SCL			0x200 0x3F0 0x4D4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_LPSPI2_PCS3			0x200 0x3F0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_GPIO3_IO11			0x200 0x3F0 0x000 0x5 0x0
+
+#endif /* _DT_BINDINGS_PINCTRL_IMXRT1050_PINFUNC_H */
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1050.dtsi b/arch/arm/boot/dts/nxp/imx/imxrt1050.dtsi
new file mode 100644
index 000000000000..dd714d235d5f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1050.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include "../../armv7-m.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/imxrt1050-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	clocks {
+		osc: osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+
+		osc3M: osc3M {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <3000000>;
+		};
+	};
+
+	soc {
+		lpuart1: serial@40184000 {
+			compatible = "fsl,imxrt1050-lpuart", "fsl,imx7ulp-lpuart";
+			reg = <0x40184000 0x4000>;
+			interrupts = <20>;
+			clocks = <&clks IMXRT1050_CLK_LPUART1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		iomuxc: pinctrl@401f8000 {
+			compatible = "fsl,imxrt1050-iomuxc";
+			reg = <0x401f8000 0x4000>;
+			fsl,mux_mask = <0x7>;
+		};
+
+		anatop: anatop@400d8000 {
+			compatible = "fsl,imxrt-anatop";
+			reg = <0x400d8000 0x4000>;
+		};
+
+		clks: clock-controller@400fc000 {
+			compatible = "fsl,imxrt1050-ccm";
+			reg = <0x400fc000 0x4000>;
+			interrupts = <95>, <96>;
+			clocks = <&osc>;
+			clock-names = "osc";
+			#clock-cells = <1>;
+			assigned-clocks = <&clks IMXRT1050_CLK_PLL1_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL1_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL2_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL3_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL3_PFD1_664_62M>,
+				<&clks IMXRT1050_CLK_PLL2_PFD2_396M>;
+			assigned-clock-parents = <&clks IMXRT1050_CLK_PLL1_REF_SEL>,
+				<&clks IMXRT1050_CLK_PLL1_ARM>,
+				<&clks IMXRT1050_CLK_PLL2_SYS>,
+				<&clks IMXRT1050_CLK_PLL3_USB_OTG>,
+				<&clks IMXRT1050_CLK_PLL3_USB_OTG>,
+				<&clks IMXRT1050_CLK_PLL2_SYS>;
+		};
+
+		edma1: dma-controller@400e8000 {
+			#dma-cells = <2>;
+			compatible = "fsl,imx7ulp-edma";
+			reg = <0x400e8000 0x4000>,
+				<0x400ec000 0x4000>;
+			dma-channels = <32>;
+			interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>, <8>,
+				<9>, <10>, <11>, <12>, <13>, <14>, <15>, <16>;
+			clock-names = "dma", "dmamux0";
+			clocks = <&clks IMXRT1050_CLK_DMA>,
+				 <&clks IMXRT1050_CLK_DMA_MUX>;
+		};
+
+		usdhc1: mmc@402c0000 {
+			compatible = "fsl,imxrt1050-usdhc", "fsl,imx6sl-usdhc";
+			reg = <0x402c0000 0x4000>;
+			interrupts = <110>;
+			clocks = <&clks IMXRT1050_CLK_IPG_PDOF>,
+				<&clks IMXRT1050_CLK_OSC>,
+				<&clks IMXRT1050_CLK_USDHC1>;
+			clock-names = "ipg", "ahb", "per";
+			bus-width = <4>;
+			fsl,wp-controller;
+			no-1-8-v;
+			max-frequency = <200000000>;
+			fsl,tuning-start-tap = <20>;
+			fsl,tuning-step = <2>;
+			status = "disabled";
+		};
+
+		gpio1: gpio@401b8000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401b8000 0x4000>;
+			interrupts = <80>, <81>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@401bc000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401bc000 0x4000>;
+			interrupts = <82>, <83>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@401c0000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401c0000 0x4000>;
+			interrupts = <84>, <85>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio@401c4000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401c4000 0x4000>;
+			interrupts = <86>, <87>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio5: gpio@400c0000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x400c0000 0x4000>;
+			interrupts = <88>, <89>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpt: timer@401ec000 {
+			compatible = "fsl,imxrt1050-gpt", "fsl,imx6dl-gpt", "fsl,imx6sl-gpt";
+			reg = <0x401ec000 0x4000>;
+			interrupts = <100>;
+			clocks = <&osc3M>;
+			clock-names = "per";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1170-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imxrt1170-pinfunc.h
new file mode 100644
index 000000000000..3b9fff2f08e1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1170-pinfunc.h
@@ -0,0 +1,1561 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2021
+ * Author(s): Jesse Taube <Mr.Bossman075@gmail.com>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H
+#define _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H
+
+#define IMX_PAD_SION		0x40000000
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+
+#define IOMUXC_GPIO_LPSR_00_FLEXCAN3_TX				0x000 0x040 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_00_MIC_CLK				0x000 0x040 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_00_MQS_RIGHT				0x000 0x040 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_00_ARM_CM4_EVENTO			0x000 0x040 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_00_GPIO_MUX6_IO00			0x000 0x040 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_00_LPUART12_TXD			0x000 0x040 0x0B0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_00_SAI4_MCLK				0x000 0x040 0x0C8 0x7 0x0
+#define IOMUXC_GPIO_LPSR_00_GPIO12_IO00				0x000 0x040 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_01_FLEXCAN3_RX				0x004 0x044 0x080 0x0 0x0
+#define IOMUXC_GPIO_LPSR_01_MIC_BITSTREAM0			0x004 0x044 0x0B4 0x1 0x0
+#define IOMUXC_GPIO_LPSR_01_MQS_LEFT				0x004 0x044 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_01_ARM_CM4_EVENTI			0x004 0x044 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_01_GPIO_MUX6_IO01			0x004 0x044 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_01_LPUART12_RXD			0x004 0x044 0x0AC 0x6 0x0
+#define IOMUXC_GPIO_LPSR_01_GPIO12_IO01				0x004 0x044 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_02_GPIO12_IO02				0x008 0x048 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_02_SRC_BOOT_MODE00			0x008 0x048 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_02_LPSPI5_SCK				0x008 0x048 0x098 0x1 0x0
+#define IOMUXC_GPIO_LPSR_02_SAI4_TX_DATA			0x008 0x048 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_02_MQS_RIGHT				0x008 0x048 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_02_GPIO_MUX6_IO02			0x008 0x048 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_LPSR_03_SRC_BOOT_MODE01			0x00C 0x04C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_03_LPSPI5_PCS0				0x00C 0x04C 0x094 0x1 0x0
+#define IOMUXC_GPIO_LPSR_03_SAI4_TX_SYNC			0x00C 0x04C 0x0DC 0x2 0x0
+#define IOMUXC_GPIO_LPSR_03_MQS_LEFT				0x00C 0x04C 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_03_GPIO_MUX6_IO03			0x00C 0x04C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_03_GPIO12_IO03				0x00C 0x04C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_04_LPI2C5_SDA				0x010 0x050 0x088 0x0 0x0
+#define IOMUXC_GPIO_LPSR_04_LPSPI5_SOUT				0x010 0x050 0x0A0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_04_SAI4_TX_BCLK			0x010 0x050 0x0D8 0x2 0x0
+#define IOMUXC_GPIO_LPSR_04_LPUART12_RTS_B			0x010 0x050 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_04_GPIO_MUX6_IO04			0x010 0x050 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_04_LPUART11_TXD			0x010 0x050 0x0A8 0x6 0x0
+#define IOMUXC_GPIO_LPSR_04_GPIO12_IO04				0x010 0x050 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_05_GPIO12_IO05				0x014 0x054 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_05_LPI2C5_SCL				0x014 0x054 0x084 0x0 0x0
+#define IOMUXC_GPIO_LPSR_05_LPSPI5_SIN				0x014 0x054 0x09C 0x1 0x0
+#define IOMUXC_GPIO_LPSR_05_SAI4_MCLK				0x014 0x054 0x0C8 0x2 0x1
+#define IOMUXC_GPIO_LPSR_05_LPUART12_CTS_B			0x014 0x054 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_05_GPIO_MUX6_IO05			0x014 0x054 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_05_LPUART11_RXD			0x014 0x054 0x0A4 0x6 0x0
+#define IOMUXC_GPIO_LPSR_05_NMI_GLUE_NMI			0x014 0x054 0x0C4 0x7 0x0
+
+#define IOMUXC_GPIO_LPSR_06_LPI2C6_SDA				0x018 0x058 0x090 0x0 0x0
+#define IOMUXC_GPIO_LPSR_06_SAI4_RX_DATA			0x018 0x058 0x0D0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_06_LPUART12_TXD			0x018 0x058 0x0B0 0x3 0x1
+#define IOMUXC_GPIO_LPSR_06_LPSPI6_PCS3				0x018 0x058 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_06_GPIO_MUX6_IO06			0x018 0x058 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_06_FLEXCAN3_TX				0x018 0x058 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_06_PIT2_TRIGGER3			0x018 0x058 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_06_LPSPI5_PCS1				0x018 0x058 0x0 0x8 0x0
+#define IOMUXC_GPIO_LPSR_06_GPIO12_IO06				0x018 0x058 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_07_LPI2C6_SCL				0x01C 0x05C 0x08C 0x0 0x0
+#define IOMUXC_GPIO_LPSR_07_SAI4_RX_BCLK			0x01C 0x05C 0x0CC 0x2 0x0
+#define IOMUXC_GPIO_LPSR_07_LPUART12_RXD			0x01C 0x05C 0x0AC 0x3 0x1
+#define IOMUXC_GPIO_LPSR_07_LPSPI6_PCS2				0x01C 0x05C 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_07_GPIO_MUX6_IO07			0x01C 0x05C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_07_FLEXCAN3_RX				0x01C 0x05C 0x080 0x6 0x1
+#define IOMUXC_GPIO_LPSR_07_PIT2_TRIGGER2			0x01C 0x05C 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_07_LPSPI5_PCS2				0x01C 0x05C 0x0 0x8 0x0
+#define IOMUXC_GPIO_LPSR_07_GPIO12_IO07				0x01C 0x05C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_08_GPIO12_IO08				0x020 0x060 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_08_LPUART11_TXD			0x020 0x060 0x0A8 0x0 0x1
+#define IOMUXC_GPIO_LPSR_08_FLEXCAN3_TX				0x020 0x060 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_08_SAI4_RX_SYNC			0x020 0x060 0x0D4 0x2 0x0
+#define IOMUXC_GPIO_LPSR_08_MIC_CLK				0x020 0x060 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_08_LPSPI6_PCS1				0x020 0x060 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_08_GPIO_MUX6_IO08			0x020 0x060 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_08_LPI2C5_SDA				0x020 0x060 0x088 0x6 0x1
+#define IOMUXC_GPIO_LPSR_08_PIT2_TRIGGER1			0x020 0x060 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_08_LPSPI5_PCS3				0x020 0x060 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_LPSR_09_GPIO12_IO09				0x024 0x064 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_09_LPUART11_RXD			0x024 0x064 0x0A4 0x0 0x1
+#define IOMUXC_GPIO_LPSR_09_FLEXCAN3_RX				0x024 0x064 0x080 0x1 0x2
+#define IOMUXC_GPIO_LPSR_09_PIT2_TRIGGER0			0x024 0x064 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_09_MIC_BITSTREAM0			0x024 0x064 0x0B4 0x3 0x1
+#define IOMUXC_GPIO_LPSR_09_LPSPI6_PCS0				0x024 0x064 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_09_GPIO_MUX6_IO09			0x024 0x064 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_09_LPI2C5_SCL				0x024 0x064 0x084 0x6 0x1
+#define IOMUXC_GPIO_LPSR_09_SAI4_TX_DATA			0x024 0x064 0x0 0x7 0x0
+
+#define IOMUXC_GPIO_LPSR_10_GPIO12_IO10				0x028 0x068 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_10_JTAG_MUX_TRSTB			0x028 0x068 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_10_LPUART11_CTS_B			0x028 0x068 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_10_LPI2C6_SDA				0x028 0x068 0x090 0x2 0x1
+#define IOMUXC_GPIO_LPSR_10_MIC_BITSTREAM1			0x028 0x068 0x0B8 0x3 0x0
+#define IOMUXC_GPIO_LPSR_10_LPSPI6_SCK				0x028 0x068 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_10_GPIO_MUX6_IO10			0x028 0x068 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_10_LPI2C5_SCLS				0x028 0x068 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_10_SAI4_TX_SYNC			0x028 0x068 0x0DC 0x7 0x1
+#define IOMUXC_GPIO_LPSR_10_LPUART12_TXD			0x028 0x068 0x0B0 0x8 0x2
+
+#define IOMUXC_GPIO_LPSR_11_JTAG_MUX_TDO			0x02C 0x06C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_11_LPUART11_RTS_B			0x02C 0x06C 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_11_LPI2C6_SCL				0x02C 0x06C 0x08C 0x2 0x1
+#define IOMUXC_GPIO_LPSR_11_MIC_BITSTREAM2			0x02C 0x06C 0x0BC 0x3 0x0
+#define IOMUXC_GPIO_LPSR_11_LPSPI6_SOUT				0x02C 0x06C 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_11_GPIO_MUX6_IO11			0x02C 0x06C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_11_LPI2C5_SDAS				0x02C 0x06C 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_11_ARM_TRACE_SWO			0x02C 0x06C 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_11_LPUART12_RXD			0x02C 0x06C 0x0AC 0x8 0x2
+#define IOMUXC_GPIO_LPSR_11_GPIO12_IO11				0x02C 0x06C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_12_GPIO12_IO12				0x030 0x070 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_12_JTAG_MUX_TDI			0x030 0x070 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_12_PIT2_TRIGGER0			0x030 0x070 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_12_MIC_BITSTREAM3			0x030 0x070 0x0C0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_12_LPSPI6_SIN				0x030 0x070 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_12_GPIO_MUX6_IO12			0x030 0x070 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_12_LPI2C5_HREQ				0x030 0x070 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_12_SAI4_TX_BCLK			0x030 0x070 0x0D8 0x7 0x1
+#define IOMUXC_GPIO_LPSR_12_LPSPI5_SCK				0x030 0x070 0x098 0x8 0x1
+
+#define IOMUXC_GPIO_LPSR_13_GPIO12_IO13				0x034 0x074 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_13_JTAG_MUX_MOD			0x034 0x074 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_13_MIC_BITSTREAM1			0x034 0x074 0x0B8 0x1 0x1
+#define IOMUXC_GPIO_LPSR_13_PIT2_TRIGGER1			0x034 0x074 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_13_GPIO_MUX6_IO13			0x034 0x074 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_13_SAI4_RX_DATA			0x034 0x074 0x0D0 0x7 0x1
+#define IOMUXC_GPIO_LPSR_13_LPSPI5_PCS0				0x034 0x074 0x094 0x8 0x1
+
+#define IOMUXC_GPIO_LPSR_14_JTAG_MUX_TCK			0x038 0x078 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_14_MIC_BITSTREAM2			0x038 0x078 0x0BC 0x1 0x1
+#define IOMUXC_GPIO_LPSR_14_PIT2_TRIGGER2			0x038 0x078 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_14_GPIO_MUX6_IO14			0x038 0x078 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_14_SAI4_RX_BCLK			0x038 0x078 0x0CC 0x7 0x1
+#define IOMUXC_GPIO_LPSR_14_LPSPI5_SOUT				0x038 0x078 0x0A0 0x8 0x1
+#define IOMUXC_GPIO_LPSR_14_GPIO12_IO14				0x038 0x078 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_15_GPIO12_IO15				0x03C 0x07C 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_15_JTAG_MUX_TMS			0x03C 0x07C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_15_MIC_BITSTREAM3			0x03C 0x07C 0x0C0 0x1 0x1
+#define IOMUXC_GPIO_LPSR_15_PIT2_TRIGGER3			0x03C 0x07C 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_15_GPIO_MUX6_IO15			0x03C 0x07C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_15_SAI4_RX_SYNC			0x03C 0x07C 0x0D4 0x7 0x1
+#define IOMUXC_GPIO_LPSR_15_LPSPI5_SIN				0x03C 0x07C 0x09C 0x8 0x1
+
+#define IOMUXC_WAKEUP_DIG_GPIO13_IO00				0x40C94000 0x40C94040 0x0 0x5 0x0
+#define IOMUXC_WAKEUP_DIG_NMI_GLUE_NMI				0x40C94000 0x40C94040 0x0C4 0x7 0x1
+
+#define IOMUXC_PMIC_ON_REQ_DIG_SNVS_LP_PMIC_ON_REQ		0x40C94004 0x40C94044 0x0 0x0 0x0
+#define IOMUXC_PMIC_ON_REQ_DIG_GPIO13_IO01			0x40C94004 0x40C94044 0x0 0x5 0x0
+
+#define IOMUXC_PMIC_STBY_REQ_DIG_CCM_PMIC_VSTBY_REQ		0x40C94008 0x40C94048 0x0 0x0 0x0
+#define IOMUXC_PMIC_STBY_REQ_DIG_GPIO13_IO02			0x40C94008 0x40C94048 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_00_DIG_SNVS_TAMPER0			0x40C9400C 0x40C9404C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_00_DIG_GPIO13_IO03			0x40C9400C 0x40C9404C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_01_DIG_SNVS_TAMPER1			0x40C94010 0x40C94050 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_01_DIG_GPIO13_IO04			0x40C94010 0x40C94050 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_02_DIG_SNVS_TAMPER2			0x40C94014 0x40C94054 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_02_DIG_GPIO13_IO05			0x40C94014 0x40C94054 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_03_DIG_SNVS_TAMPER3			0x40C94018 0x40C94058 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_03_DIG_GPIO13_IO06			0x40C94018 0x40C94058 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_04_DIG_SNVS_TAMPER4			0x40C9401C 0x40C9405C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_04_DIG_GPIO13_IO07			0x40C9401C 0x40C9405C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_05_DIG_SNVS_TAMPER5			0x40C94020 0x40C94060 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_05_DIG_GPIO13_IO08			0x40C94020 0x40C94060 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_06_DIG_SNVS_TAMPER6			0x40C94024 0x40C94064 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_06_DIG_GPIO13_IO09			0x40C94024 0x40C94064 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_07_DIG_SNVS_TAMPER7			0x40C94028 0x40C94068 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_07_DIG_GPIO13_IO10			0x40C94028 0x40C94068 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_08_DIG_SNVS_TAMPER8			0x40C9402C 0x40C9406C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_08_DIG_GPIO13_IO11			0x40C9402C 0x40C9406C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_09_DIG_SNVS_TAMPER9			0x40C94030 0x40C94070 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_09_DIG_GPIO13_IO12			0x40C94030 0x40C94070 0x0 0x5 0x0
+
+#define IOMUXC_TEST_MODE_DIG					0x0 0x40C94034 0x0 0x0 0x0
+
+#define IOMUXC_POR_B_DIG					0x0 0x40C94038 0x0 0x0 0x0
+
+#define IOMUXC_ONOFF_DIG					0x0 0x40C9403C 0x0 0x0 0x0
+
+#define IOMUXC_GPIO_EMC_B1_00_SEMC_DATA00			0x010 0x254 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_00_FLEXPWM4_PWM0_A			0x010 0x254 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_00_GPIO_MUX1_IO00			0x010 0x254 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_00_FLEXIO1_D00			0x010 0x254 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_00_GPIO7_IO00			0x010 0x254 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_01_GPIO7_IO01			0x014 0x258 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_01_SEMC_DATA01			0x014 0x258 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_01_FLEXPWM4_PWM0_B			0x014 0x258 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_01_GPIO_MUX1_IO01			0x014 0x258 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_01_FLEXIO1_D01			0x014 0x258 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_02_SEMC_DATA02			0x018 0x25C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_02_FLEXPWM4_PWM1_A			0x018 0x25C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_02_GPIO_MUX1_IO02			0x018 0x25C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_02_FLEXIO1_D02			0x018 0x25C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_02_GPIO7_IO02			0x018 0x25C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_03_SEMC_DATA03			0x01C 0x260 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_03_FLEXPWM4_PWM1_B			0x01C 0x260 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_03_GPIO_MUX1_IO03			0x01C 0x260 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_03_FLEXIO1_D03			0x01C 0x260 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_03_GPIO7_IO03			0x01C 0x260 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_04_GPIO7_IO04			0x020 0x264 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_04_SEMC_DATA04			0x020 0x264 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_04_FLEXPWM4_PWM2_A			0x020 0x264 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_04_GPIO_MUX1_IO04			0x020 0x264 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_04_FLEXIO1_D04			0x020 0x264 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_05_SEMC_DATA05			0x024 0x268 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_05_FLEXPWM4_PWM2_B			0x024 0x268 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_05_GPIO_MUX1_IO05			0x024 0x268 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_05_FLEXIO1_D05			0x024 0x268 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_05_GPIO7_IO05			0x024 0x268 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_06_SEMC_DATA06			0x028 0x26C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_06_FLEXPWM2_PWM0_A			0x028 0x26C 0x518 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_06_GPIO_MUX1_IO06			0x028 0x26C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_06_FLEXIO1_D06			0x028 0x26C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_06_GPIO7_IO06			0x028 0x26C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_07_GPIO7_IO07			0x02C 0x270 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_07_SEMC_DATA07			0x02C 0x270 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_07_FLEXPWM2_PWM0_B			0x02C 0x270 0x524 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_07_GPIO_MUX1_IO07			0x02C 0x270 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_07_FLEXIO1_D07			0x02C 0x270 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_08_SEMC_DM00				0x030 0x274 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_08_FLEXPWM2_PWM1_A			0x030 0x274 0x51C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_08_GPIO_MUX1_IO08			0x030 0x274 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_08_FLEXIO1_D08			0x030 0x274 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_08_GPIO7_IO08			0x030 0x274 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_09_SEMC_ADDR00			0x034 0x278 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_09_FLEXPWM2_PWM1_B			0x034 0x278 0x528 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPT5_CAPTURE1			0x034 0x278 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPIO_MUX1_IO09			0x034 0x278 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_09_FLEXIO1_D09			0x034 0x278 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPIO7_IO09			0x034 0x278 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_10_SEMC_ADDR01			0x038 0x27C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_10_FLEXPWM2_PWM2_A			0x038 0x27C 0x520 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPT5_CAPTURE2			0x038 0x27C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPIO_MUX1_IO10			0x038 0x27C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_10_FLEXIO1_D10			0x038 0x27C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPIO7_IO10			0x038 0x27C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_11_GPIO7_IO11			0x03C 0x280 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_11_SEMC_ADDR02			0x03C 0x280 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_11_FLEXPWM2_PWM2_B			0x03C 0x280 0x52C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_11_GPT5_COMPARE1			0x03C 0x280 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_11_GPIO_MUX1_IO11			0x03C 0x280 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_11_FLEXIO1_D11			0x03C 0x280 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_12_SEMC_ADDR03			0x040 0x284 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_12_XBAR1_INOUT04			0x040 0x284 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPT5_COMPARE2			0x040 0x284 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPIO_MUX1_IO12			0x040 0x284 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_12_FLEXIO1_D12			0x040 0x284 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPIO7_IO12			0x040 0x284 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_13_SEMC_ADDR04			0x044 0x288 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_13_XBAR1_INOUT05			0x044 0x288 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPT5_COMPARE3			0x044 0x288 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPIO_MUX1_IO13			0x044 0x288 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_13_FLEXIO1_D13			0x044 0x288 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPIO7_IO13			0x044 0x288 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_14_GPIO7_IO14			0x048 0x28C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_14_SEMC_ADDR05			0x048 0x28C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_14_XBAR1_INOUT06			0x048 0x28C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_14_GPT5_CLK				0x048 0x28C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_14_GPIO_MUX1_IO14			0x048 0x28C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_14_FLEXIO1_D14			0x048 0x28C 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_15_SEMC_ADDR06			0x04C 0x290 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_15_XBAR1_INOUT07			0x04C 0x290 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_15_GPIO_MUX1_IO15			0x04C 0x290 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_15_FLEXIO1_D15			0x04C 0x290 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_15_GPIO7_IO15			0x04C 0x290 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_16_SEMC_ADDR07			0x050 0x294 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_16_XBAR1_INOUT08			0x050 0x294 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_16_GPIO_MUX1_IO16			0x050 0x294 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_16_FLEXIO1_D16			0x050 0x294 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_16_GPIO7_IO16			0x050 0x294 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_17_GPIO7_IO17			0x054 0x298 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_17_SEMC_ADDR08			0x054 0x298 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_17_FLEXPWM4_PWM3_A			0x054 0x298 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_17_TMR1_TIMER0			0x054 0x298 0x63C 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_17_GPIO_MUX1_IO17			0x054 0x298 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_17_FLEXIO1_D17			0x054 0x298 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_18_SEMC_ADDR09			0x058 0x29C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_18_FLEXPWM4_PWM3_B			0x058 0x29C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_18_TMR2_TIMER0			0x058 0x29C 0x648 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_18_GPIO_MUX1_IO18			0x058 0x29C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_18_FLEXIO1_D18			0x058 0x29C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_18_GPIO7_IO18			0x058 0x29C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_19_SEMC_ADDR11			0x05C 0x2A0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_19_FLEXPWM2_PWM3_A			0x05C 0x2A0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_19_TMR3_TIMER0			0x05C 0x2A0 0x654 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_19_GPIO_MUX1_IO19			0x05C 0x2A0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_19_FLEXIO1_D19			0x05C 0x2A0 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_19_GPIO7_IO19			0x05C 0x2A0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_20_SEMC_ADDR12			0x060 0x2A4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_20_FLEXPWM2_PWM3_B			0x060 0x2A4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_20_TMR4_TIMER0			0x060 0x2A4 0x660 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_20_GPIO_MUX1_IO20			0x060 0x2A4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_20_FLEXIO1_D20			0x060 0x2A4 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_20_GPIO7_IO20			0x060 0x2A4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_21_GPIO7_IO21			0x064 0x2A8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_21_SEMC_BA0				0x064 0x2A8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_21_FLEXPWM3_PWM3_A			0x064 0x2A8 0x53C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_21_GPIO_MUX1_IO21			0x064 0x2A8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_21_FLEXIO1_D21			0x064 0x2A8 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_22_GPIO7_IO22			0x068 0x2AC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_22_SEMC_BA1				0x068 0x2AC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_22_FLEXPWM3_PWM3_B			0x068 0x2AC 0x54C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_22_GPIO_MUX1_IO22			0x068 0x2AC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_22_FLEXIO1_D22			0x068 0x2AC 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_23_SEMC_ADDR10			0x06C 0x2B0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_23_FLEXPWM1_PWM0_A			0x06C 0x2B0 0x500 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_23_GPIO_MUX1_IO23			0x06C 0x2B0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_23_FLEXIO1_D23			0x06C 0x2B0 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_23_GPIO7_IO23			0x06C 0x2B0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_24_GPIO7_IO24			0x070 0x2B4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_24_SEMC_CAS				0x070 0x2B4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_24_FLEXPWM1_PWM0_B			0x070 0x2B4 0x50C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_24_GPIO_MUX1_IO24			0x070 0x2B4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_24_FLEXIO1_D24			0x070 0x2B4 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_25_GPIO7_IO25			0x074 0x2B8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_25_SEMC_RAS				0x074 0x2B8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_25_FLEXPWM1_PWM1_A			0x074 0x2B8 0x504 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_25_GPIO_MUX1_IO25			0x074 0x2B8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_25_FLEXIO1_D25			0x074 0x2B8 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_26_SEMC_CLK				0x078 0x2BC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_26_FLEXPWM1_PWM1_B			0x078 0x2BC 0x510 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_26_GPIO_MUX1_IO26			0x078 0x2BC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_26_FLEXIO1_D26			0x078 0x2BC 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_26_GPIO7_IO26			0x078 0x2BC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_27_GPIO7_IO27			0x07C 0x2C0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_27_SEMC_CKE				0x07C 0x2C0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_27_FLEXPWM1_PWM2_A			0x07C 0x2C0 0x508 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_27_GPIO_MUX1_IO27			0x07C 0x2C0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_27_FLEXIO1_D27			0x07C 0x2C0 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_28_GPIO7_IO28			0x080 0x2C4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_28_SEMC_WE				0x080 0x2C4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_28_FLEXPWM1_PWM2_B			0x080 0x2C4 0x514 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_28_GPIO_MUX1_IO28			0x080 0x2C4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_28_FLEXIO1_D28			0x080 0x2C4 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_29_SEMC_CS0				0x084 0x2C8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_29_FLEXPWM3_PWM0_A			0x084 0x2C8 0x530 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_29_GPIO_MUX1_IO29			0x084 0x2C8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_29_FLEXIO1_D29			0x084 0x2C8 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_29_GPIO7_IO29			0x084 0x2C8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_30_SEMC_DATA08			0x088 0x2CC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_30_FLEXPWM3_PWM0_B			0x088 0x2CC 0x540 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_30_GPIO_MUX1_IO30			0x088 0x2CC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_30_FLEXIO1_D30			0x088 0x2CC 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_30_GPIO7_IO30			0x088 0x2CC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_31_GPIO7_IO31			0x08C 0x2D0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_31_SEMC_DATA09			0x08C 0x2D0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_31_FLEXPWM3_PWM1_A			0x08C 0x2D0 0x534 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_31_GPIO_MUX1_IO31			0x08C 0x2D0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_31_FLEXIO1_D31			0x08C 0x2D0 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_32_GPIO8_IO00			0x090 0x2D4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_32_SEMC_DATA10			0x090 0x2D4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_32_FLEXPWM3_PWM1_B			0x090 0x2D4 0x544 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_32_GPIO_MUX2_IO00			0x090 0x2D4 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_33_SEMC_DATA11			0x094 0x2D8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_33_FLEXPWM3_PWM2_A			0x094 0x2D8 0x538 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_33_GPIO_MUX2_IO01			0x094 0x2D8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_33_GPIO8_IO01			0x094 0x2D8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_34_GPIO8_IO02			0x098 0x2DC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_34_SEMC_DATA12			0x098 0x2DC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_34_FLEXPWM3_PWM2_B			0x098 0x2DC 0x548 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_34_GPIO_MUX2_IO02			0x098 0x2DC 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_35_GPIO8_IO03			0x09C 0x2E0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_35_SEMC_DATA13			0x09C 0x2E0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_35_XBAR1_INOUT09			0x09C 0x2E0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_35_GPIO_MUX2_IO03			0x09C 0x2E0 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_36_SEMC_DATA14			0x0A0 0x2E4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_36_XBAR1_INOUT10			0x0A0 0x2E4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_36_GPIO_MUX2_IO04			0x0A0 0x2E4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_36_GPIO8_IO04			0x0A0 0x2E4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_37_GPIO8_IO05			0x0A4 0x2E8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_37_SEMC_DATA15			0x0A4 0x2E8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_37_XBAR1_INOUT11			0x0A4 0x2E8 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_37_GPIO_MUX2_IO05			0x0A4 0x2E8 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_38_GPIO8_IO06			0x0A8 0x2EC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_38_SEMC_DM01				0x0A8 0x2EC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_38_FLEXPWM1_PWM3_A			0x0A8 0x2EC 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_38_TMR1_TIMER1			0x0A8 0x2EC 0x640 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_38_GPIO_MUX2_IO06			0x0A8 0x2EC 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_39_SEMC_DQS				0x0AC 0x2F0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_39_FLEXPWM1_PWM3_B			0x0AC 0x2F0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_39_TMR2_TIMER1			0x0AC 0x2F0 0x64C 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_39_GPIO_MUX2_IO07			0x0AC 0x2F0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_39_GPIO8_IO07			0x0AC 0x2F0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_40_SEMC_RDY				0x0B0 0x2F4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_40_XBAR1_INOUT12			0x0B0 0x2F4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_40_MQS_RIGHT				0x0B0 0x2F4 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_40_LPUART6_TXD			0x0B0 0x2F4 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B1_40_GPIO_MUX2_IO08			0x0B0 0x2F4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_40_ENET_1G_MDC			0x0B0 0x2F4 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B1_40_CCM_CLKO1				0x0B0 0x2F4 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B1_40_GPIO8_IO08			0x0B0 0x2F4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_41_GPIO8_IO09			0x0B4 0x2F8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_41_SEMC_CSX00			0x0B4 0x2F8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_41_XBAR1_INOUT13			0x0B4 0x2F8 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_41_MQS_LEFT				0x0B4 0x2F8 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_41_LPUART6_RXD			0x0B4 0x2F8 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B1_41_FLEXSPI2_B_DATA07			0x0B4 0x2F8 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B1_41_GPIO_MUX2_IO09			0x0B4 0x2F8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_41_ENET_1G_MDIO			0x0B4 0x2F8 0x4C8 0x7 0x0
+#define IOMUXC_GPIO_EMC_B1_41_CCM_CLKO2				0x0B4 0x2F8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_00_SEMC_DATA16			0x0B8 0x2FC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_00_CCM_ENET_REF_CLK_25M		0x0B8 0x2FC 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_00_TMR3_TIMER1			0x0B8 0x2FC 0x658 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPUART6_CTS_B			0x0B8 0x2FC 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_00_FLEXSPI2_B_DATA06			0x0B8 0x2FC 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_00_GPIO_MUX2_IO10			0x0B8 0x2FC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_00_XBAR1_INOUT20			0x0B8 0x2FC 0x6D8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_00_ENET_QOS_1588_EVENT1_OUT		0x0B8 0x2FC 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPSPI1_SCK			0x0B8 0x2FC 0x5D0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPI2C2_SCL			0x0B8 0x2FC 0x5B4 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_00_GPIO8_IO10			0x0B8 0x2FC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_00_FLEXPWM3_PWM0_A			0x0B8 0x2FC 0x530 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_01_SEMC_DATA17			0x0BC 0x300 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_01_USDHC2_CD_B			0x0BC 0x300 0x6D0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_01_TMR4_TIMER1			0x0BC 0x300 0x664 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPUART6_RTS_B			0x0BC 0x300 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_01_FLEXSPI2_B_DATA05			0x0BC 0x300 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_01_GPIO_MUX2_IO11			0x0BC 0x300 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_01_XBAR1_INOUT21			0x0BC 0x300 0x6DC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_01_ENET_QOS_1588_EVENT1_IN		0x0BC 0x300 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPSPI1_PCS0			0x0BC 0x300 0x5CC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPI2C2_SDA			0x0BC 0x300 0x5B8 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_01_GPIO8_IO11			0x0BC 0x300 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_01_FLEXPWM3_PWM0_B			0x0BC 0x300 0x540 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_02_SEMC_DATA18			0x0C0 0x304 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_02_USDHC2_WP				0x0C0 0x304 0x6D4 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_02_VIDEO_MUX_CSI_DATA23		0x0C0 0x304 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_02_FLEXSPI2_B_DATA04			0x0C0 0x304 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_02_GPIO_MUX2_IO12			0x0C0 0x304 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_02_XBAR1_INOUT22			0x0C0 0x304 0x6E0 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_02_ENET_QOS_1588_EVENT1_AUX_IN	0x0C0 0x304 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_02_LPSPI1_SOUT			0x0C0 0x304 0x5D8 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_02_GPIO8_IO12			0x0C0 0x304 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_02_FLEXPWM3_PWM1_A			0x0C0 0x304 0x534 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_03_SEMC_DATA19			0x0C4 0x308 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_03_USDHC2_VSELECT			0x0C4 0x308 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_03_VIDEO_MUX_CSI_DATA22		0x0C4 0x308 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_03_FLEXSPI2_B_DATA03			0x0C4 0x308 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_03_GPIO_MUX2_IO13			0x0C4 0x308 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_03_XBAR1_INOUT23			0x0C4 0x308 0x6E4 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_03_ENET_1G_TX_DATA03			0x0C4 0x308 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_03_LPSPI1_SIN			0x0C4 0x308 0x5D4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_03_GPIO8_IO13			0x0C4 0x308 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_03_FLEXPWM3_PWM1_B			0x0C4 0x308 0x544 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_04_SEMC_DATA20			0x0C8 0x30C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_04_USDHC2_RESET_B			0x0C8 0x30C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_04_SAI2_MCLK				0x0C8 0x30C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_04_VIDEO_MUX_CSI_DATA21		0x0C8 0x30C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_04_FLEXSPI2_B_DATA02			0x0C8 0x30C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_04_GPIO_MUX2_IO14			0x0C8 0x30C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_04_XBAR1_INOUT24			0x0C8 0x30C 0x6E8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_04_ENET_1G_TX_DATA02			0x0C8 0x30C 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_04_LPSPI3_SCK			0x0C8 0x30C 0x600 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_04_GPIO8_IO14			0x0C8 0x30C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_04_FLEXPWM3_PWM2_A			0x0C8 0x30C 0x538 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_05_SEMC_DATA21			0x0CC 0x310 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPT3_CLK				0x0CC 0x310 0x598 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_05_SAI2_RX_SYNC			0x0CC 0x310 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_05_VIDEO_MUX_CSI_DATA20		0x0CC 0x310 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_05_FLEXSPI2_B_DATA01			0x0CC 0x310 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPIO_MUX2_IO15			0x0CC 0x310 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_05_XBAR1_INOUT25			0x0CC 0x310 0x6EC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_05_ENET_1G_RX_CLK			0x0CC 0x310 0x4CC 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_05_LPSPI3_PCS0			0x0CC 0x310 0x5F0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_05_PIT1_TRIGGER0			0x0CC 0x310 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPIO8_IO15			0x0CC 0x310 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_05_FLEXPWM3_PWM2_B			0x0CC 0x310 0x548 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_06_SEMC_DATA22			0x0D0 0x314 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPT3_CAPTURE1			0x0D0 0x314 0x590 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPIO8_IO16			0x0D0 0x314 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_06_SAI2_RX_BCLK			0x0D0 0x314 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_06_FLEXPWM3_PWM3_A			0x0D0 0x314 0x53C 0xB 0x1
+#define IOMUXC_GPIO_EMC_B2_06_VIDEO_MUX_CSI_DATA19		0x0D0 0x314 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_06_FLEXSPI2_B_DATA00			0x0D0 0x314 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPIO_MUX2_IO16			0x0D0 0x314 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_06_XBAR1_INOUT26			0x0D0 0x314 0x6F0 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_06_ENET_1G_TX_ER			0x0D0 0x314 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_06_LPSPI3_SOUT			0x0D0 0x314 0x608 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_06_PIT1_TRIGGER1			0x0D0 0x314 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_07_SEMC_DATA23			0x0D4 0x318 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPT3_CAPTURE2			0x0D4 0x318 0x594 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_07_SAI2_RX_DATA			0x0D4 0x318 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_07_VIDEO_MUX_CSI_DATA18		0x0D4 0x318 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_07_FLEXSPI2_B_DQS			0x0D4 0x318 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPIO_MUX2_IO17			0x0D4 0x318 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_07_XBAR1_INOUT27			0x0D4 0x318 0x6F4 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_07_ENET_1G_RX_DATA03			0x0D4 0x318 0x4DC 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_07_LPSPI3_SIN			0x0D4 0x318 0x604 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_07_PIT1_TRIGGER2			0x0D4 0x318 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPIO8_IO17			0x0D4 0x318 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_07_FLEXPWM3_PWM3_B			0x0D4 0x318 0x54C 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_08_SEMC_DM02				0x0D8 0x31C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPT3_COMPARE1			0x0D8 0x31C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_08_SAI2_TX_DATA			0x0D8 0x31C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_08_VIDEO_MUX_CSI_DATA17		0x0D8 0x31C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_08_FLEXSPI2_B_SS0_B			0x0D8 0x31C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPIO_MUX2_IO18			0x0D8 0x31C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_08_XBAR1_INOUT28			0x0D8 0x31C 0x6F8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_08_ENET_1G_RX_DATA02			0x0D8 0x31C 0x4D8 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_08_LPSPI3_PCS1			0x0D8 0x31C 0x5F4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_08_PIT1_TRIGGER3			0x0D8 0x31C 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPIO8_IO18			0x0D8 0x31C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_09_GPIO8_IO19			0x0DC 0x320 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_09_SEMC_DATA24			0x0DC 0x320 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_09_GPT3_COMPARE2			0x0DC 0x320 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_09_SAI2_TX_BCLK			0x0DC 0x320 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_09_VIDEO_MUX_CSI_DATA16		0x0DC 0x320 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_09_FLEXSPI2_B_SCLK			0x0DC 0x320 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_09_GPIO_MUX2_IO19			0x0DC 0x320 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_09_XBAR1_INOUT29			0x0DC 0x320 0x6FC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_09_ENET_1G_CRS			0x0DC 0x320 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_09_LPSPI3_PCS2			0x0DC 0x320 0x5F8 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_09_TMR1_TIMER0			0x0DC 0x320 0x63C 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_10_GPIO8_IO20			0x0E0 0x324 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_10_SEMC_DATA25			0x0E0 0x324 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_10_GPT3_COMPARE3			0x0E0 0x324 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_10_SAI2_TX_SYNC			0x0E0 0x324 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_10_VIDEO_MUX_CSI_FIELD		0x0E0 0x324 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_10_FLEXSPI2_A_SCLK			0x0E0 0x324 0x58C 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_10_GPIO_MUX2_IO20			0x0E0 0x324 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_10_XBAR1_INOUT30			0x0E0 0x324 0x700 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_10_ENET_1G_COL			0x0E0 0x324 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_10_LPSPI3_PCS3			0x0E0 0x324 0x5FC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_10_TMR1_TIMER1			0x0E0 0x324 0x640 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_11_SEMC_DATA26			0x0E4 0x328 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_11_SPDIF_IN				0x0E4 0x328 0x6B4 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_11_ENET_1G_TX_DATA00			0x0E4 0x328 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_11_SAI3_RX_SYNC			0x0E4 0x328 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_11_FLEXSPI2_A_SS0_B			0x0E4 0x328 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_11_GPIO_MUX2_IO21			0x0E4 0x328 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_11_XBAR1_INOUT31			0x0E4 0x328 0x704 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_11_EMVSIM1_IO			0x0E4 0x328 0x69C 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_11_TMR1_TIMER2			0x0E4 0x328 0x644 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_11_GPIO8_IO21			0x0E4 0x328 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_12_SEMC_DATA27			0x0E8 0x32C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_12_SPDIF_OUT				0x0E8 0x32C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_12_ENET_1G_TX_DATA01			0x0E8 0x32C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_12_SAI3_RX_BCLK			0x0E8 0x32C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_12_FLEXSPI2_A_DQS			0x0E8 0x32C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_12_GPIO_MUX2_IO22			0x0E8 0x32C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_12_XBAR1_INOUT32			0x0E8 0x32C 0x708 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_12_EMVSIM1_CLK			0x0E8 0x32C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_12_TMR1_TIMER3			0x0E8 0x32C 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_12_GPIO8_IO22			0x0E8 0x32C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_13_GPIO8_IO23			0x0EC 0x330 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_13_SEMC_DATA28			0x0EC 0x330 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_13_ENET_1G_TX_EN			0x0EC 0x330 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_13_SAI3_RX_DATA			0x0EC 0x330 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_13_FLEXSPI2_A_DATA00			0x0EC 0x330 0x57C 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_13_GPIO_MUX2_IO23			0x0EC 0x330 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_13_XBAR1_INOUT33			0x0EC 0x330 0x70C 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_13_EMVSIM1_RST			0x0EC 0x330 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_13_TMR2_TIMER0			0x0EC 0x330 0x648 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_14_SEMC_DATA29			0x0F0 0x334 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_14_ENET_1G_TX_CLK_IO			0x0F0 0x334 0x4E8 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_14_SAI3_TX_DATA			0x0F0 0x334 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_14_FLEXSPI2_A_DATA01			0x0F0 0x334 0x580 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_14_GPIO_MUX2_IO24			0x0F0 0x334 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_14_XBAR1_INOUT34			0x0F0 0x334 0x710 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_14_SFA_ipp_do_atx_clk_under_test	0x0F0 0x334 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_14_EMVSIM1_SVEN			0x0F0 0x334 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_14_TMR2_TIMER1			0x0F0 0x334 0x64C 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_14_GPIO8_IO24			0x0F0 0x334 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_15_SEMC_DATA30			0x0F4 0x338 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_15_ENET_1G_RX_DATA00			0x0F4 0x338 0x4D0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_15_SAI3_TX_BCLK			0x0F4 0x338 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_15_FLEXSPI2_A_DATA02			0x0F4 0x338 0x584 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_15_GPIO_MUX2_IO25			0x0F4 0x338 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_15_XBAR1_INOUT35			0x0F4 0x338 0x714 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_15_EMVSIM1_PD			0x0F4 0x338 0x6A0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_15_TMR2_TIMER2			0x0F4 0x338 0x650 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_15_GPIO8_IO25			0x0F4 0x338 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_16_GPIO8_IO26			0x0F8 0x33C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_16_SEMC_DATA31			0x0F8 0x33C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_16_XBAR1_INOUT14			0x0F8 0x33C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_16_ENET_1G_RX_DATA01			0x0F8 0x33C 0x4D4 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_16_SAI3_TX_SYNC			0x0F8 0x33C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_16_FLEXSPI2_A_DATA03			0x0F8 0x33C 0x588 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_16_GPIO_MUX2_IO26			0x0F8 0x33C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_16_EMVSIM1_POWER_FAIL		0x0F8 0x33C 0x6A4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_16_TMR2_TIMER3			0x0F8 0x33C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_17_SEMC_DM03				0x0FC 0x340 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_17_XBAR1_INOUT15			0x0FC 0x340 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_17_ENET_1G_RX_EN			0x0FC 0x340 0x4E0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_17_SAI3_MCLK				0x0FC 0x340 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_17_FLEXSPI2_A_DATA04			0x0FC 0x340 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_17_GPIO_MUX2_IO27			0x0FC 0x340 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_17_WDOG1_ANY				0x0FC 0x340 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_17_TMR3_TIMER0			0x0FC 0x340 0x654 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_17_GPIO8_IO27			0x0FC 0x340 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_18_SEMC_DQS4				0x100 0x344 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_18_XBAR1_INOUT16			0x100 0x344 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_18_ENET_1G_RX_ER			0x100 0x344 0x4E4 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_18_EWM_OUT_B				0x100 0x344 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_18_FLEXSPI2_A_DATA05			0x100 0x344 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_18_GPIO_MUX2_IO28			0x100 0x344 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_18_FLEXSPI1_A_DQS			0x100 0x344 0x550 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_18_WDOG1_B				0x100 0x344 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_18_TMR3_TIMER1			0x100 0x344 0x658 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_18_GPIO8_IO28			0x100 0x344 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_19_GPIO8_IO29			0x104 0x348 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_19_SEMC_CLKX00			0x104 0x348 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_MDC				0x104 0x348 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_1G_MDC			0x104 0x348 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_1G_REF_CLK			0x104 0x348 0x4C4 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_19_FLEXSPI2_A_DATA06			0x104 0x348 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_19_GPIO_MUX2_IO29			0x104 0x348 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_QOS_MDC			0x104 0x348 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_19_TMR3_TIMER2			0x104 0x348 0x65C 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_20_GPIO8_IO30			0x108 0x34C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_20_SEMC_CLKX01			0x108 0x34C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_MDIO				0x108 0x34C 0x4AC 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_1G_MDIO			0x108 0x34C 0x4C8 0x2 0x1
+#define IOMUXC_GPIO_EMC_B2_20_ENET_QOS_REF_CLK			0x108 0x34C 0x4A0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_20_FLEXSPI2_A_DATA07			0x108 0x34C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_20_GPIO_MUX2_IO30			0x108 0x34C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_QOS_MDIO			0x108 0x34C 0x4EC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_20_TMR3_TIMER3			0x108 0x34C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_00_GPIO8_IO31				0x10C 0x350 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_00_EMVSIM1_IO				0x10C 0x350 0x69C 0x0 0x1
+#define IOMUXC_GPIO_AD_00_FLEXCAN2_TX				0x10C 0x350 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_00_ENET_1G_1588_EVENT1_IN		0x10C 0x350 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_00_GPT2_CAPTURE1				0x10C 0x350 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_00_FLEXPWM1_PWM0_A			0x10C 0x350 0x500 0x4 0x1
+#define IOMUXC_GPIO_AD_00_GPIO_MUX2_IO31			0x10C 0x350 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_00_LPUART7_TXD				0x10C 0x350 0x630 0x6 0x0
+#define IOMUXC_GPIO_AD_00_FLEXIO2_D00				0x10C 0x350 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_00_FLEXSPI2_B_SS1_B			0x10C 0x350 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_01_GPIO9_IO00				0x110 0x354 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_01_EMVSIM1_CLK				0x110 0x354 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_01_FLEXCAN2_RX				0x110 0x354 0x49C 0x1 0x0
+#define IOMUXC_GPIO_AD_01_ENET_1G_1588_EVENT1_OUT		0x110 0x354 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_01_GPT2_CAPTURE2				0x110 0x354 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_01_FLEXPWM1_PWM0_B			0x110 0x354 0x50C 0x4 0x1
+#define IOMUXC_GPIO_AD_01_GPIO_MUX3_IO00			0x110 0x354 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_01_LPUART7_RXD				0x110 0x354 0x62C 0x6 0x0
+#define IOMUXC_GPIO_AD_01_FLEXIO2_D01				0x110 0x354 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_01_FLEXSPI2_A_SS1_B			0x110 0x354 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_02_GPIO9_IO01				0x114 0x358 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_02_EMVSIM1_RST				0x114 0x358 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_02_LPUART7_CTS_B				0x114 0x358 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_02_ENET_1G_1588_EVENT2_IN		0x114 0x358 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_02_GPT2_COMPARE1				0x114 0x358 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_02_FLEXPWM1_PWM1_A			0x114 0x358 0x504 0x4 0x1
+#define IOMUXC_GPIO_AD_02_GPIO_MUX3_IO01			0x114 0x358 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_02_LPUART8_TXD				0x114 0x358 0x638 0x6 0x0
+#define IOMUXC_GPIO_AD_02_FLEXIO2_D02				0x114 0x358 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_02_VIDEO_MUX_EXT_DCIC1			0x114 0x358 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_03_GPIO9_IO02				0x118 0x35C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_03_EMVSIM1_SVEN				0x118 0x35C 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_03_LPUART7_RTS_B				0x118 0x35C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_03_ENET_1G_1588_EVENT2_OUT		0x118 0x35C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_03_GPT2_COMPARE2				0x118 0x35C 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_03_FLEXPWM1_PWM1_B			0x118 0x35C 0x510 0x4 0x1
+#define IOMUXC_GPIO_AD_03_GPIO_MUX3_IO02			0x118 0x35C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_03_LPUART8_RXD				0x118 0x35C 0x634 0x6 0x0
+#define IOMUXC_GPIO_AD_03_FLEXIO2_D03				0x118 0x35C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_03_VIDEO_MUX_EXT_DCIC2			0x118 0x35C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_04_EMVSIM1_PD				0x11C 0x360 0x6A0 0x0 0x1
+#define IOMUXC_GPIO_AD_04_LPUART8_CTS_B				0x11C 0x360 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_04_ENET_1G_1588_EVENT3_IN		0x11C 0x360 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_04_GPT2_COMPARE3				0x11C 0x360 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_04_FLEXPWM1_PWM2_A			0x11C 0x360 0x508 0x4 0x1
+#define IOMUXC_GPIO_AD_04_GPIO_MUX3_IO03			0x11C 0x360 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_04_WDOG1_B				0x11C 0x360 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_04_FLEXIO2_D04				0x11C 0x360 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_04_TMR4_TIMER0				0x11C 0x360 0x660 0x9 0x1
+#define IOMUXC_GPIO_AD_04_GPIO9_IO03				0x11C 0x360 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_05_EMVSIM1_POWER_FAIL			0x120 0x364 0x6A4 0x0 0x1
+#define IOMUXC_GPIO_AD_05_LPUART8_RTS_B				0x120 0x364 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_05_ENET_1G_1588_EVENT3_OUT		0x120 0x364 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_05_GPT2_CLK				0x120 0x364 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_05_FLEXPWM1_PWM2_B			0x120 0x364 0x514 0x4 0x1
+#define IOMUXC_GPIO_AD_05_GPIO_MUX3_IO04			0x120 0x364 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_05_WDOG2_B				0x120 0x364 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_05_FLEXIO2_D05				0x120 0x364 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_05_TMR4_TIMER1				0x120 0x364 0x664 0x9 0x1
+#define IOMUXC_GPIO_AD_05_GPIO9_IO04				0x120 0x364 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_06_USB_OTG2_OC				0x124 0x368 0x6B8 0x0 0x0
+#define IOMUXC_GPIO_AD_06_FLEXCAN1_TX				0x124 0x368 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_06_EMVSIM2_IO				0x124 0x368 0x6A8 0x2 0x0
+#define IOMUXC_GPIO_AD_06_GPT3_CAPTURE1				0x124 0x368 0x590 0x3 0x1
+#define IOMUXC_GPIO_AD_06_VIDEO_MUX_CSI_DATA15			0x124 0x368 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_06_GPIO_MUX3_IO05			0x124 0x368 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_06_ENET_1588_EVENT1_IN			0x124 0x368 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_06_FLEXIO2_D06				0x124 0x368 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_06_TMR4_TIMER2				0x124 0x368 0x668 0x9 0x0
+#define IOMUXC_GPIO_AD_06_GPIO9_IO05				0x124 0x368 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_06_FLEXPWM1_PWM0_X			0x124 0x368 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_07_USB_OTG2_PWR				0x128 0x36C 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_07_FLEXCAN1_RX				0x128 0x36C 0x498 0x1 0x0
+#define IOMUXC_GPIO_AD_07_EMVSIM2_CLK				0x128 0x36C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_07_GPT3_CAPTURE2				0x128 0x36C 0x594 0x3 0x1
+#define IOMUXC_GPIO_AD_07_VIDEO_MUX_CSI_DATA14			0x128 0x36C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_07_GPIO_MUX3_IO06			0x128 0x36C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_07_ENET_1588_EVENT1_OUT			0x128 0x36C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_07_FLEXIO2_D07				0x128 0x36C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_07_TMR4_TIMER3				0x128 0x36C 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_07_GPIO9_IO06				0x128 0x36C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_07_FLEXPWM1_PWM1_X			0x128 0x36C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_08_USBPHY2_OTG_ID			0x12C 0x370 0x6C4 0x0 0x0
+#define IOMUXC_GPIO_AD_08_LPI2C1_SCL				0x12C 0x370 0x5AC 0x1 0x0
+#define IOMUXC_GPIO_AD_08_EMVSIM2_RST				0x12C 0x370 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_08_GPT3_COMPARE1				0x12C 0x370 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_08_VIDEO_MUX_CSI_DATA13			0x12C 0x370 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_08_GPIO_MUX3_IO07			0x12C 0x370 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_08_ENET_1588_EVENT2_IN			0x12C 0x370 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_08_FLEXIO2_D08				0x12C 0x370 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_08_GPIO9_IO07				0x12C 0x370 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_08_FLEXPWM1_PWM2_X			0x12C 0x370 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_09_USBPHY1_OTG_ID			0x130 0x374 0x6C0 0x0 0x0
+#define IOMUXC_GPIO_AD_09_LPI2C1_SDA				0x130 0x374 0x5B0 0x1 0x0
+#define IOMUXC_GPIO_AD_09_EMVSIM2_SVEN				0x130 0x374 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_09_GPT3_COMPARE2				0x130 0x374 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_09_VIDEO_MUX_CSI_DATA12			0x130 0x374 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_09_GPIO_MUX3_IO08			0x130 0x374 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_09_ENET_1588_EVENT2_OUT			0x130 0x374 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_09_FLEXIO2_D09				0x130 0x374 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_09_GPIO9_IO08				0x130 0x374 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_09_FLEXPWM1_PWM3_X			0x130 0x374 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_10_USB_OTG1_PWR				0x134 0x378 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_10_LPI2C1_SCLS				0x134 0x378 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_10_EMVSIM2_PD				0x134 0x378 0x6AC 0x2 0x0
+#define IOMUXC_GPIO_AD_10_GPT3_COMPARE3				0x134 0x378 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_10_VIDEO_MUX_CSI_DATA11			0x134 0x378 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_10_GPIO_MUX3_IO09			0x134 0x378 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_10_ENET_1588_EVENT3_IN			0x134 0x378 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_10_FLEXIO2_D10				0x134 0x378 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_10_GPIO9_IO09				0x134 0x378 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_10_FLEXPWM2_PWM0_X			0x134 0x378 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_11_USB_OTG1_OC				0x138 0x37C 0x6BC 0x0 0x0
+#define IOMUXC_GPIO_AD_11_LPI2C1_SDAS				0x138 0x37C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_11_EMVSIM2_POWER_FAIL			0x138 0x37C 0x6B0 0x2 0x0
+#define IOMUXC_GPIO_AD_11_GPT3_CLK				0x138 0x37C 0x598 0x3 0x1
+#define IOMUXC_GPIO_AD_11_VIDEO_MUX_CSI_DATA10			0x138 0x37C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_11_GPIO_MUX3_IO10			0x138 0x37C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_11_ENET_1588_EVENT3_OUT			0x138 0x37C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_11_FLEXIO2_D11				0x138 0x37C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_11_GPIO9_IO10				0x138 0x37C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_11_FLEXPWM2_PWM1_X			0x138 0x37C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_12_SPDIF_LOCK				0x13C 0x380 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_12_LPI2C1_HREQ				0x13C 0x380 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_12_GPT1_CAPTURE1				0x13C 0x380 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_12_FLEXSPI1_B_DATA03			0x13C 0x380 0x570 0x3 0x0
+#define IOMUXC_GPIO_AD_12_VIDEO_MUX_CSI_PIXCLK			0x13C 0x380 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_12_GPIO_MUX3_IO11			0x13C 0x380 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_12_ENET_TX_DATA03			0x13C 0x380 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_12_FLEXIO2_D12				0x13C 0x380 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_12_EWM_OUT_B				0x13C 0x380 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_12_GPIO9_IO11				0x13C 0x380 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_12_FLEXPWM2_PWM2_X			0x13C 0x380 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_13_SPDIF_SR_CLK				0x140 0x384 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_13_PIT1_TRIGGER0				0x140 0x384 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_13_GPT1_CAPTURE2				0x140 0x384 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_13_FLEXSPI1_B_DATA02			0x140 0x384 0x56C 0x3 0x0
+#define IOMUXC_GPIO_AD_13_VIDEO_MUX_CSI_MCLK			0x140 0x384 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_13_GPIO_MUX3_IO12			0x140 0x384 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_13_ENET_TX_DATA02			0x140 0x384 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_13_FLEXIO2_D13				0x140 0x384 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_13_REF_CLK_32K				0x140 0x384 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_13_GPIO9_IO12				0x140 0x384 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_13_FLEXPWM2_PWM3_X			0x140 0x384 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_14_SPDIF_EXT_CLK				0x144 0x388 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_14_REF_CLK_24M				0x144 0x388 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_14_GPT1_COMPARE1				0x144 0x388 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_14_FLEXSPI1_B_DATA01			0x144 0x388 0x568 0x3 0x0
+#define IOMUXC_GPIO_AD_14_VIDEO_MUX_CSI_VSYNC			0x144 0x388 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_14_GPIO_MUX3_IO13			0x144 0x388 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_14_ENET_RX_CLK				0x144 0x388 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_14_FLEXIO2_D14				0x144 0x388 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_14_CCM_ENET_REF_CLK_25M			0x144 0x388 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_14_GPIO9_IO13				0x144 0x388 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_14_FLEXPWM3_PWM0_X			0x144 0x388 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_15_GPIO9_IO14				0x148 0x38C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_15_FLEXPWM3_PWM1_X			0x148 0x38C 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_15_SPDIF_IN				0x148 0x38C 0x6B4 0x0 0x1
+#define IOMUXC_GPIO_AD_15_LPUART10_TXD				0x148 0x38C 0x628 0x1 0x0
+#define IOMUXC_GPIO_AD_15_GPT1_COMPARE2				0x148 0x38C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_15_FLEXSPI1_B_DATA00			0x148 0x38C 0x564 0x3 0x0
+#define IOMUXC_GPIO_AD_15_VIDEO_MUX_CSI_HSYNC			0x148 0x38C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_15_GPIO_MUX3_IO14			0x148 0x38C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_15_ENET_TX_ER				0x148 0x38C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_15_FLEXIO2_D15				0x148 0x38C 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_AD_16_SPDIF_OUT				0x14C 0x390 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_16_LPUART10_RXD				0x14C 0x390 0x624 0x1 0x0
+#define IOMUXC_GPIO_AD_16_GPT1_COMPARE3				0x14C 0x390 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_16_FLEXSPI1_B_SCLK			0x14C 0x390 0x578 0x3 0x0
+#define IOMUXC_GPIO_AD_16_VIDEO_MUX_CSI_DATA09			0x14C 0x390 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_16_GPIO_MUX3_IO15			0x14C 0x390 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_16_ENET_RX_DATA03			0x14C 0x390 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_16_FLEXIO2_D16				0x14C 0x390 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_16_ENET_1G_MDC				0x14C 0x390 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_16_GPIO9_IO15				0x14C 0x390 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_16_FLEXPWM3_PWM2_X			0x14C 0x390 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_17_SAI1_MCLK				0x150 0x394 0x66C 0x0 0x0
+#define IOMUXC_GPIO_AD_17_ACMP1_OUT				0x150 0x394 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_17_GPT1_CLK				0x150 0x394 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_17_FLEXSPI1_A_DQS			0x150 0x394 0x550 0x3 0x1
+#define IOMUXC_GPIO_AD_17_VIDEO_MUX_CSI_DATA08			0x150 0x394 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_17_GPIO_MUX3_IO16			0x150 0x394 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_17_ENET_RX_DATA02			0x150 0x394 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_17_FLEXIO2_D17				0x150 0x394 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_17_ENET_1G_MDIO				0x150 0x394 0x4C8 0x9 0x2
+#define IOMUXC_GPIO_AD_17_GPIO9_IO16				0x150 0x394 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_17_FLEXPWM3_PWM3_X			0x150 0x394 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_18_GPIO9_IO17				0x154 0x398 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_18_FLEXPWM4_PWM0_X			0x154 0x398 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_18_SAI1_RX_SYNC				0x154 0x398 0x678 0x0 0x0
+#define IOMUXC_GPIO_AD_18_ACMP2_OUT				0x154 0x398 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_18_LPSPI1_PCS1				0x154 0x398 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_18_FLEXSPI1_A_SS0_B			0x154 0x398 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_18_VIDEO_MUX_CSI_DATA07			0x154 0x398 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_18_GPIO_MUX3_IO17			0x154 0x398 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_18_ENET_CRS				0x154 0x398 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_18_FLEXIO2_D18				0x154 0x398 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_18_LPI2C2_SCL				0x154 0x398 0x5B4 0x9 0x1
+
+#define IOMUXC_GPIO_AD_19_SAI1_RX_BCLK				0x158 0x39C 0x670 0x0 0x0
+#define IOMUXC_GPIO_AD_19_ACMP3_OUT				0x158 0x39C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_19_LPSPI1_PCS2				0x158 0x39C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_19_FLEXSPI1_A_SCLK			0x158 0x39C 0x574 0x3 0x0
+#define IOMUXC_GPIO_AD_19_VIDEO_MUX_CSI_DATA06			0x158 0x39C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_19_GPIO_MUX3_IO18			0x158 0x39C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_19_ENET_COL				0x158 0x39C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_19_FLEXIO2_D19				0x158 0x39C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_19_LPI2C2_SDA				0x158 0x39C 0x5B8 0x9 0x1
+#define IOMUXC_GPIO_AD_19_GPIO9_IO18				0x158 0x39C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_19_FLEXPWM4_PWM1_X			0x158 0x39C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_20_SAI1_RX_DATA00			0x15C 0x3A0 0x674 0x0 0x0
+#define IOMUXC_GPIO_AD_20_ACMP4_OUT				0x15C 0x3A0 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_20_LPSPI1_PCS3				0x15C 0x3A0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_20_FLEXSPI1_A_DATA00			0x15C 0x3A0 0x554 0x3 0x0
+#define IOMUXC_GPIO_AD_20_VIDEO_MUX_CSI_DATA05			0x15C 0x3A0 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_20_GPIO_MUX3_IO19			0x15C 0x3A0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_20_KPP_ROW07				0x15C 0x3A0 0x5A8 0x6 0x0
+#define IOMUXC_GPIO_AD_20_FLEXIO2_D20				0x15C 0x3A0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_20_ENET_QOS_1588_EVENT2_OUT		0x15C 0x3A0 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_20_GPIO9_IO19				0x15C 0x3A0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_20_FLEXPWM4_PWM2_X			0x15C 0x3A0 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_21_SAI1_TX_DATA00			0x160 0x3A4 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_21_LPSPI2_PCS1				0x160 0x3A4 0x5E0 0x2 0x0
+#define IOMUXC_GPIO_AD_21_FLEXSPI1_A_DATA01			0x160 0x3A4 0x558 0x3 0x0
+#define IOMUXC_GPIO_AD_21_VIDEO_MUX_CSI_DATA04			0x160 0x3A4 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_21_GPIO_MUX3_IO20			0x160 0x3A4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_21_KPP_COL07				0x160 0x3A4 0x5A0 0x6 0x0
+#define IOMUXC_GPIO_AD_21_FLEXIO2_D21				0x160 0x3A4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_21_ENET_QOS_1588_EVENT2_IN		0x160 0x3A4 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_21_GPIO9_IO20				0x160 0x3A4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_21_FLEXPWM4_PWM3_X			0x160 0x3A4 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_22_GPIO9_IO21				0x164 0x3A8 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_22_SAI1_TX_BCLK				0x164 0x3A8 0x67C 0x0 0x0
+#define IOMUXC_GPIO_AD_22_LPSPI2_PCS2				0x164 0x3A8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_22_FLEXSPI1_A_DATA02			0x164 0x3A8 0x55C 0x3 0x0
+#define IOMUXC_GPIO_AD_22_VIDEO_MUX_CSI_DATA03			0x164 0x3A8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_22_GPIO_MUX3_IO21			0x164 0x3A8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_22_KPP_ROW06				0x164 0x3A8 0x5A4 0x6 0x0
+#define IOMUXC_GPIO_AD_22_FLEXIO2_D22				0x164 0x3A8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_22_ENET_QOS_1588_EVENT3_OUT		0x164 0x3A8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_23_SAI1_TX_SYNC				0x168 0x3AC 0x680 0x0 0x0
+#define IOMUXC_GPIO_AD_23_LPSPI2_PCS3				0x168 0x3AC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_23_FLEXSPI1_A_DATA03			0x168 0x3AC 0x560 0x3 0x0
+#define IOMUXC_GPIO_AD_23_VIDEO_MUX_CSI_DATA02			0x168 0x3AC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_23_GPIO_MUX3_IO22			0x168 0x3AC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_23_KPP_COL06				0x168 0x3AC 0x59C 0x6 0x0
+#define IOMUXC_GPIO_AD_23_FLEXIO2_D23				0x168 0x3AC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_23_ENET_QOS_1588_EVENT3_IN		0x168 0x3AC 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_23_GPIO9_IO22				0x168 0x3AC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_24_LPUART1_TXD				0x16C 0x3B0 0x620 0x0 0x0
+#define IOMUXC_GPIO_AD_24_LPSPI2_SCK				0x16C 0x3B0 0x5E4 0x1 0x0
+#define IOMUXC_GPIO_AD_24_VIDEO_MUX_CSI_DATA00			0x16C 0x3B0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_24_ENET_RX_EN				0x16C 0x3B0 0x4B8 0x3 0x0
+#define IOMUXC_GPIO_AD_24_FLEXPWM2_PWM0_A			0x16C 0x3B0 0x518 0x4 0x1
+#define IOMUXC_GPIO_AD_24_GPIO_MUX3_IO23			0x16C 0x3B0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_24_KPP_ROW05				0x16C 0x3B0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_24_FLEXIO2_D24				0x16C 0x3B0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_24_LPI2C4_SCL				0x16C 0x3B0 0x5C4 0x9 0x0
+#define IOMUXC_GPIO_AD_24_GPIO9_IO23				0x16C 0x3B0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_25_GPIO9_IO24				0x170 0x3B4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_25_LPUART1_RXD				0x170 0x3B4 0x61C 0x0 0x0
+#define IOMUXC_GPIO_AD_25_LPSPI2_PCS0				0x170 0x3B4 0x5DC 0x1 0x0
+#define IOMUXC_GPIO_AD_25_VIDEO_MUX_CSI_DATA01			0x170 0x3B4 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_25_ENET_RX_ER				0x170 0x3B4 0x4BC 0x3 0x0
+#define IOMUXC_GPIO_AD_25_FLEXPWM2_PWM0_B			0x170 0x3B4 0x524 0x4 0x1
+#define IOMUXC_GPIO_AD_25_GPIO_MUX3_IO24			0x170 0x3B4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_25_KPP_COL05				0x170 0x3B4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_25_FLEXIO2_D25				0x170 0x3B4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_25_LPI2C4_SDA				0x170 0x3B4 0x5C8 0x9 0x0
+
+#define IOMUXC_GPIO_AD_26_LPUART1_CTS_B				0x174 0x3B8 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_26_LPSPI2_SOUT				0x174 0x3B8 0x5EC 0x1 0x0
+#define IOMUXC_GPIO_AD_26_SEMC_CSX01				0x174 0x3B8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_26_ENET_RX_DATA00			0x174 0x3B8 0x4B0 0x3 0x0
+#define IOMUXC_GPIO_AD_26_FLEXPWM2_PWM1_A			0x174 0x3B8 0x51C 0x4 0x1
+#define IOMUXC_GPIO_AD_26_GPIO_MUX3_IO25			0x174 0x3B8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_26_KPP_ROW04				0x174 0x3B8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_26_FLEXIO2_D26				0x174 0x3B8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_26_ENET_QOS_MDC				0x174 0x3B8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_26_GPIO9_IO25				0x174 0x3B8 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_26_USDHC2_CD_B				0x174 0x3B8 0x6D0 0xB 0x1
+
+#define IOMUXC_GPIO_AD_27_LPUART1_RTS_B				0x178 0x3BC 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_27_LPSPI2_SIN				0x178 0x3BC 0x5E8 0x1 0x0
+#define IOMUXC_GPIO_AD_27_SEMC_CSX02				0x178 0x3BC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_27_ENET_RX_DATA01			0x178 0x3BC 0x4B4 0x3 0x0
+#define IOMUXC_GPIO_AD_27_FLEXPWM2_PWM1_B			0x178 0x3BC 0x528 0x4 0x1
+#define IOMUXC_GPIO_AD_27_GPIO_MUX3_IO26			0x178 0x3BC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_27_KPP_COL04				0x178 0x3BC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_27_FLEXIO2_D27				0x178 0x3BC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_27_ENET_QOS_MDIO				0x178 0x3BC 0x4EC 0x9 0x1
+#define IOMUXC_GPIO_AD_27_GPIO9_IO26				0x178 0x3BC 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_27_USDHC2_WP				0x178 0x3BC 0x6D4 0xB 0x1
+
+#define IOMUXC_GPIO_AD_28_GPIO9_IO27				0x17C 0x3C0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_28_USDHC2_VSELECT			0x17C 0x3C0 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_28_LPSPI1_SCK				0x17C 0x3C0 0x5D0 0x0 0x1
+#define IOMUXC_GPIO_AD_28_LPUART5_TXD				0x17C 0x3C0 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_28_SEMC_CSX03				0x17C 0x3C0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_28_ENET_TX_EN				0x17C 0x3C0 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_28_FLEXPWM2_PWM2_A			0x17C 0x3C0 0x520 0x4 0x1
+#define IOMUXC_GPIO_AD_28_GPIO_MUX3_IO27			0x17C 0x3C0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_28_KPP_ROW03				0x17C 0x3C0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_28_FLEXIO2_D28				0x17C 0x3C0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_28_VIDEO_MUX_EXT_DCIC1			0x17C 0x3C0 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_29_LPSPI1_PCS0				0x180 0x3C4 0x5CC 0x0 0x1
+#define IOMUXC_GPIO_AD_29_LPUART5_RXD				0x180 0x3C4 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_29_ENET_REF_CLK				0x180 0x3C4 0x4A8 0x2 0x0
+#define IOMUXC_GPIO_AD_29_ENET_TX_CLK				0x180 0x3C4 0x4C0 0x3 0x0
+#define IOMUXC_GPIO_AD_29_FLEXPWM2_PWM2_B			0x180 0x3C4 0x52C 0x4 0x1
+#define IOMUXC_GPIO_AD_29_GPIO_MUX3_IO28			0x180 0x3C4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_29_KPP_COL03				0x180 0x3C4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_29_FLEXIO2_D29				0x180 0x3C4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_29_VIDEO_MUX_EXT_DCIC2			0x180 0x3C4 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_29_GPIO9_IO28				0x180 0x3C4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_29_USDHC2_RESET_B			0x180 0x3C4 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_30_LPSPI1_SOUT				0x184 0x3C8 0x5D8 0x0 0x1
+#define IOMUXC_GPIO_AD_30_USB_OTG2_OC				0x184 0x3C8 0x6B8 0x1 0x1
+#define IOMUXC_GPIO_AD_30_FLEXCAN2_TX				0x184 0x3C8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_30_ENET_TX_DATA00			0x184 0x3C8 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_30_LPUART3_TXD				0x184 0x3C8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_30_GPIO_MUX3_IO29			0x184 0x3C8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_30_KPP_ROW02				0x184 0x3C8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_30_FLEXIO2_D30				0x184 0x3C8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_30_WDOG2_RESET_B_DEB			0x184 0x3C8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_30_GPIO9_IO29				0x184 0x3C8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_31_LPSPI1_SIN				0x188 0x3CC 0x5D4 0x0 0x1
+#define IOMUXC_GPIO_AD_31_USB_OTG2_PWR				0x188 0x3CC 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_31_FLEXCAN2_RX				0x188 0x3CC 0x49C 0x2 0x1
+#define IOMUXC_GPIO_AD_31_ENET_TX_DATA01			0x188 0x3CC 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_31_LPUART3_RXD				0x188 0x3CC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_31_GPIO_MUX3_IO30			0x188 0x3CC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_31_KPP_COL02				0x188 0x3CC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_31_FLEXIO2_D31				0x188 0x3CC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_31_WDOG1_RESET_B_DEB			0x188 0x3CC 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_31_GPIO9_IO30				0x188 0x3CC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_32_GPIO9_IO31				0x18C 0x3D0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_32_LPI2C1_SCL				0x18C 0x3D0 0x5AC 0x0 0x1
+#define IOMUXC_GPIO_AD_32_USBPHY2_OTG_ID			0x18C 0x3D0 0x6C4 0x1 0x1
+#define IOMUXC_GPIO_AD_32_PGMC_PMIC_RDY				0x18C 0x3D0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_32_ENET_MDC				0x18C 0x3D0 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_32_USDHC1_CD_B				0x18C 0x3D0 0x6C8 0x4 0x0
+#define IOMUXC_GPIO_AD_32_GPIO_MUX3_IO31			0x18C 0x3D0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_32_KPP_ROW01				0x18C 0x3D0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_32_LPUART10_TXD				0x18C 0x3D0 0x628 0x8 0x1
+#define IOMUXC_GPIO_AD_32_ENET_1G_MDC				0x18C 0x3D0 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_33_LPI2C1_SDA				0x190 0x3D4 0x5B0 0x0 0x1
+#define IOMUXC_GPIO_AD_33_USBPHY1_OTG_ID			0x190 0x3D4 0x6C0 0x1 0x1
+#define IOMUXC_GPIO_AD_33_XBAR1_INOUT17				0x190 0x3D4 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_33_ENET_MDIO				0x190 0x3D4 0x4AC 0x3 0x1
+#define IOMUXC_GPIO_AD_33_USDHC1_WP				0x190 0x3D4 0x6CC 0x4 0x0
+#define IOMUXC_GPIO_AD_33_GPIO_MUX4_IO00			0x190 0x3D4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_33_KPP_COL01				0x190 0x3D4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_33_LPUART10_RXD				0x190 0x3D4 0x624 0x8 0x1
+#define IOMUXC_GPIO_AD_33_ENET_1G_MDIO				0x190 0x3D4 0x4C8 0x9 0x3
+#define IOMUXC_GPIO_AD_33_GPIO10_IO00				0x190 0x3D4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_34_ENET_1G_1588_EVENT0_IN		0x194 0x3D8 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_34_USB_OTG1_PWR				0x194 0x3D8 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_34_XBAR1_INOUT18				0x194 0x3D8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_34_ENET_1588_EVENT0_IN			0x194 0x3D8 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_34_USDHC1_VSELECT			0x194 0x3D8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_34_GPIO_MUX4_IO01			0x194 0x3D8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_34_KPP_ROW00				0x194 0x3D8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_34_LPUART10_CTS_B			0x194 0x3D8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_34_WDOG1_ANY				0x194 0x3D8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_34_GPIO10_IO01				0x194 0x3D8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_35_GPIO10_IO02				0x198 0x3DC 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_35_ENET_1G_1588_EVENT0_OUT		0x198 0x3DC 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_35_USB_OTG1_OC				0x198 0x3DC 0x6BC 0x1 0x1
+#define IOMUXC_GPIO_AD_35_XBAR1_INOUT19				0x198 0x3DC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_35_ENET_1588_EVENT0_OUT			0x198 0x3DC 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_35_USDHC1_RESET_B			0x198 0x3DC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_35_GPIO_MUX4_IO02			0x198 0x3DC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_35_KPP_COL00				0x198 0x3DC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_35_LPUART10_RTS_B			0x198 0x3DC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_35_FLEXSPI1_B_SS1_B			0x198 0x3DC 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B1_00_USDHC1_CMD				0x19C 0x3E0 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_00_XBAR1_INOUT20			0x19C 0x3E0 0x6D8 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_00_GPT4_CAPTURE1			0x19C 0x3E0 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_00_GPIO_MUX4_IO03			0x19C 0x3E0 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_00_FLEXSPI2_A_SS0_B			0x19C 0x3E0 0x0 0x6 0x0
+#define IOMUXC_GPIO_SD_B1_00_KPP_ROW07				0x19C 0x3E0 0x5A8 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_00_GPIO10_IO03			0x19C 0x3E0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_01_USDHC1_CLK				0x1A0 0x3E4 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_01_XBAR1_INOUT21			0x1A0 0x3E4 0x6DC 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_01_GPT4_CAPTURE2			0x1A0 0x3E4 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_01_GPIO_MUX4_IO04			0x1A0 0x3E4 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_01_FLEXSPI2_A_SCLK			0x1A0 0x3E4 0x58C 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_01_KPP_COL07				0x1A0 0x3E4 0x5A0 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_01_GPIO10_IO04			0x1A0 0x3E4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_02_GPIO10_IO05			0x1A4 0x3E8 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B1_02_USDHC1_DATA0			0x1A4 0x3E8 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_02_XBAR1_INOUT22			0x1A4 0x3E8 0x6E0 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_02_GPT4_COMPARE1			0x1A4 0x3E8 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_02_GPIO_MUX4_IO05			0x1A4 0x3E8 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_02_FLEXSPI2_A_DATA00			0x1A4 0x3E8 0x57C 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_02_KPP_ROW06				0x1A4 0x3E8 0x5A4 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_02_FLEXSPI1_A_SS1_B			0x1A4 0x3E8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B1_03_USDHC1_DATA1			0x1A8 0x3EC 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_03_XBAR1_INOUT23			0x1A8 0x3EC 0x6E4 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_03_GPT4_COMPARE2			0x1A8 0x3EC 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_03_GPIO_MUX4_IO06			0x1A8 0x3EC 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_03_FLEXSPI2_A_DATA01			0x1A8 0x3EC 0x580 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_03_KPP_COL06				0x1A8 0x3EC 0x59C 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_03_FLEXSPI1_B_SS1_B			0x1A8 0x3EC 0x0 0x9 0x0
+#define IOMUXC_GPIO_SD_B1_03_GPIO10_IO06			0x1A8 0x3EC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_04_USDHC1_DATA2			0x1AC 0x3F0 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_04_XBAR1_INOUT24			0x1AC 0x3F0 0x6E8 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_04_GPT4_COMPARE3			0x1AC 0x3F0 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_04_GPIO_MUX4_IO07			0x1AC 0x3F0 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_04_FLEXSPI2_A_DATA02			0x1AC 0x3F0 0x584 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_04_FLEXSPI1_B_SS0_B			0x1AC 0x3F0 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B1_04_ENET_QOS_1588_EVENT2_AUX_IN	0x1AC 0x3F0 0x0 0x9 0x0
+#define IOMUXC_GPIO_SD_B1_04_GPIO10_IO07			0x1AC 0x3F0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_05_GPIO10_IO08			0x1B0 0x3F4 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B1_05_USDHC1_DATA3			0x1B0 0x3F4 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_05_XBAR1_INOUT25			0x1B0 0x3F4 0x6EC 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_05_GPT4_CLK				0x1B0 0x3F4 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_05_GPIO_MUX4_IO08			0x1B0 0x3F4 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_05_FLEXSPI2_A_DATA03			0x1B0 0x3F4 0x588 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_05_FLEXSPI1_B_DQS			0x1B0 0x3F4 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B1_05_ENET_QOS_1588_EVENT3_AUX_IN	0x1B0 0x3F4 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B2_00_GPIO10_IO09			0x1B4 0x3F8 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_00_USDHC2_DATA3			0x1B4 0x3F8 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_00_FLEXSPI1_B_DATA03			0x1B4 0x3F8 0x570 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_00_ENET_1G_RX_EN			0x1B4 0x3F8 0x4E0 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_00_LPUART9_TXD			0x1B4 0x3F8 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_00_LPSPI4_SCK				0x1B4 0x3F8 0x610 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_00_GPIO_MUX4_IO09			0x1B4 0x3F8 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_01_USDHC2_DATA2			0x1B8 0x3FC 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_01_FLEXSPI1_B_DATA02			0x1B8 0x3FC 0x56C 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_01_ENET_1G_RX_CLK			0x1B8 0x3FC 0x4CC 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_01_LPUART9_RXD			0x1B8 0x3FC 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_01_LPSPI4_PCS0			0x1B8 0x3FC 0x60C 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_01_GPIO_MUX4_IO10			0x1B8 0x3FC 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_01_GPIO10_IO10			0x1B8 0x3FC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_02_GPIO10_IO11			0x1BC 0x400 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_02_USDHC2_DATA1			0x1BC 0x400 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_02_FLEXSPI1_B_DATA01			0x1BC 0x400 0x568 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_02_ENET_1G_RX_DATA00			0x1BC 0x400 0x4D0 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_02_LPUART9_CTS_B			0x1BC 0x400 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_02_LPSPI4_SOUT			0x1BC 0x400 0x618 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_02_GPIO_MUX4_IO11			0x1BC 0x400 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_03_GPIO10_IO12			0x1C0 0x404 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_03_USDHC2_DATA0			0x1C0 0x404 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_03_FLEXSPI1_B_DATA00			0x1C0 0x404 0x564 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_03_ENET_1G_RX_DATA01			0x1C0 0x404 0x4D4 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_03_LPUART9_RTS_B			0x1C0 0x404 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_03_LPSPI4_SIN				0x1C0 0x404 0x614 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_03_GPIO_MUX4_IO12			0x1C0 0x404 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_04_USDHC2_CLK				0x1C4 0x408 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_04_FLEXSPI1_B_SCLK			0x1C4 0x408 0x578 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_04_ENET_1G_RX_DATA02			0x1C4 0x408 0x4D8 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_04_FLEXSPI1_A_SS1_B			0x1C4 0x408 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_04_LPSPI4_PCS1			0x1C4 0x408 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_04_GPIO_MUX4_IO13			0x1C4 0x408 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_04_GPIO10_IO13			0x1C4 0x408 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_05_GPIO10_IO14			0x1C8 0x40C 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_05_USDHC2_CMD				0x1C8 0x40C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_05_FLEXSPI1_A_DQS			0x1C8 0x40C 0x550 0x1 0x2
+#define IOMUXC_GPIO_SD_B2_05_ENET_1G_RX_DATA03			0x1C8 0x40C 0x4DC 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_05_FLEXSPI1_B_SS0_B			0x1C8 0x40C 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_05_LPSPI4_PCS2			0x1C8 0x40C 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_05_GPIO_MUX4_IO14			0x1C8 0x40C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_06_GPIO10_IO15			0x1CC 0x410 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_06_USDHC2_RESET_B			0x1CC 0x410 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_06_FLEXSPI1_A_SS0_B			0x1CC 0x410 0x0 0x1 0x0
+#define IOMUXC_GPIO_SD_B2_06_ENET_1G_TX_DATA03			0x1CC 0x410 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_06_LPSPI4_PCS3			0x1CC 0x410 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_06_GPT6_CAPTURE1			0x1CC 0x410 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_06_GPIO_MUX4_IO15			0x1CC 0x410 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_07_USDHC2_STROBE			0x1D0 0x414 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_07_FLEXSPI1_A_SCLK			0x1D0 0x414 0x574 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_07_ENET_1G_TX_DATA02			0x1D0 0x414 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_07_LPUART3_CTS_B			0x1D0 0x414 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_07_GPT6_CAPTURE2			0x1D0 0x414 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_07_GPIO_MUX4_IO16			0x1D0 0x414 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_07_LPSPI2_SCK				0x1D0 0x414 0x5E4 0x6 0x1
+#define IOMUXC_GPIO_SD_B2_07_ENET_TX_ER				0x1D0 0x414 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B2_07_ENET_QOS_REF_CLK			0x1D0 0x414 0x4A0 0x9 0x1
+#define IOMUXC_GPIO_SD_B2_07_GPIO10_IO16			0x1D0 0x414 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_08_GPIO10_IO17			0x1D4 0x418 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_08_USDHC2_DATA4			0x1D4 0x418 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_08_FLEXSPI1_A_DATA00			0x1D4 0x418 0x554 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_08_ENET_1G_TX_DATA01			0x1D4 0x418 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_08_LPUART3_RTS_B			0x1D4 0x418 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_08_GPT6_COMPARE1			0x1D4 0x418 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_08_GPIO_MUX4_IO17			0x1D4 0x418 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_08_LPSPI2_PCS0			0x1D4 0x418 0x5DC 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_09_GPIO10_IO18			0x1D8 0x41C 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_09_USDHC2_DATA5			0x1D8 0x41C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_09_FLEXSPI1_A_DATA01			0x1D8 0x41C 0x558 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_09_ENET_1G_TX_DATA00			0x1D8 0x41C 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_09_LPUART5_CTS_B			0x1D8 0x41C 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_09_GPT6_COMPARE2			0x1D8 0x41C 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_09_GPIO_MUX4_IO18			0x1D8 0x41C 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_09_LPSPI2_SOUT			0x1D8 0x41C 0x5EC 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_10_GPIO10_IO19			0x1DC 0x420 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_10_USDHC2_DATA6			0x1DC 0x420 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_10_FLEXSPI1_A_DATA02			0x1DC 0x420 0x55C 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_10_ENET_1G_TX_EN			0x1DC 0x420 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_10_LPUART5_RTS_B			0x1DC 0x420 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_10_GPT6_COMPARE3			0x1DC 0x420 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_10_GPIO_MUX4_IO19			0x1DC 0x420 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_10_LPSPI2_SIN				0x1DC 0x420 0x5E8 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_11_USDHC2_DATA7			0x1E0 0x424 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_11_FLEXSPI1_A_DATA03			0x1E0 0x424 0x560 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_11_ENET_1G_TX_CLK_IO			0x1E0 0x424 0x4E8 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_11_ENET_1G_REF_CLK			0x1E0 0x424 0x4C4 0x3 0x1
+#define IOMUXC_GPIO_SD_B2_11_GPT6_CLK				0x1E0 0x424 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_11_GPIO_MUX4_IO20			0x1E0 0x424 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_11_LPSPI2_PCS1			0x1E0 0x424 0x5E0 0x6 0x1
+#define IOMUXC_GPIO_SD_B2_11_GPIO10_IO20			0x1E0 0x424 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_00_VIDEO_MUX_LCDIF_CLK		0x1E4 0x428 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_00_ENET_1G_RX_EN			0x1E4 0x428 0x4E0 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_00_TMR1_TIMER0			0x1E4 0x428 0x63C 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_00_XBAR1_INOUT26			0x1E4 0x428 0x6F0 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_00_GPIO_MUX4_IO21			0x1E4 0x428 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_00_ENET_QOS_RX_EN			0x1E4 0x428 0x4F8 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_00_GPIO10_IO21			0x1E4 0x428 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_01_VIDEO_MUX_LCDIF_ENABLE		0x1E8 0x42C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_1G_RX_CLK			0x1E8 0x42C 0x4CC 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_01_ENET_1G_RX_ER			0x1E8 0x42C 0x4E4 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_01_TMR1_TIMER1			0x1E8 0x42C 0x640 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_01_XBAR1_INOUT27			0x1E8 0x42C 0x6F4 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_01_GPIO_MUX4_IO22			0x1E8 0x42C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_QOS_RX_CLK			0x1E8 0x42C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_QOS_RX_ER			0x1E8 0x42C 0x4FC 0x9 0x0
+#define IOMUXC_GPIO_DISP_B1_01_GPIO10_IO22			0x1E8 0x42C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_02_GPIO10_IO23			0x1EC 0x430 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_02_VIDEO_MUX_LCDIF_HSYNC		0x1EC 0x430 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_02_ENET_1G_RX_DATA00		0x1EC 0x430 0x4D0 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_02_LPI2C3_SCL			0x1EC 0x430 0x5BC 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_02_TMR1_TIMER2			0x1EC 0x430 0x644 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_02_XBAR1_INOUT28			0x1EC 0x430 0x6F8 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_02_GPIO_MUX4_IO23			0x1EC 0x430 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_02_ENET_QOS_RX_DATA00		0x1EC 0x430 0x4F0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_02_LPUART1_TXD			0x1EC 0x430 0x620 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_03_VIDEO_MUX_LCDIF_VSYNC		0x1F0 0x434 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_03_ENET_1G_RX_DATA01		0x1F0 0x434 0x4D4 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_03_LPI2C3_SDA			0x1F0 0x434 0x5C0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_03_TMR2_TIMER0			0x1F0 0x434 0x648 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_03_XBAR1_INOUT29			0x1F0 0x434 0x6FC 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_03_GPIO_MUX4_IO24			0x1F0 0x434 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_03_ENET_QOS_RX_DATA01		0x1F0 0x434 0x4F4 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_03_LPUART1_RXD			0x1F0 0x434 0x61C 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_03_GPIO10_IO24			0x1F0 0x434 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_04_VIDEO_MUX_LCDIF_DATA00		0x1F4 0x438 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_04_ENET_1G_RX_DATA02		0x1F4 0x438 0x4D8 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_04_LPUART4_RXD			0x1F4 0x438 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_04_TMR2_TIMER1			0x1F4 0x438 0x64C 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_04_XBAR1_INOUT30			0x1F4 0x438 0x700 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_04_GPIO_MUX4_IO25			0x1F4 0x438 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_04_ENET_QOS_RX_DATA02		0x1F4 0x438 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_04_LPSPI3_SCK			0x1F4 0x438 0x600 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_04_GPIO10_IO25			0x1F4 0x438 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_05_GPIO10_IO26			0x1F8 0x43C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_05_VIDEO_MUX_LCDIF_DATA01		0x1F8 0x43C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_05_ENET_1G_RX_DATA03		0x1F8 0x43C 0x4DC 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_05_LPUART4_CTS_B			0x1F8 0x43C 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_05_TMR2_TIMER2			0x1F8 0x43C 0x650 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_05_XBAR1_INOUT31			0x1F8 0x43C 0x704 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_05_GPIO_MUX4_IO26			0x1F8 0x43C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_05_ENET_QOS_RX_DATA03		0x1F8 0x43C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_05_LPSPI3_SIN			0x1F8 0x43C 0x604 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_06_VIDEO_MUX_LCDIF_DATA02		0x1FC 0x440 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_06_ENET_1G_TX_DATA03		0x1FC 0x440 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_06_LPUART4_TXD			0x1FC 0x440 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_06_TMR3_TIMER0			0x1FC 0x440 0x654 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_06_XBAR1_INOUT32			0x1FC 0x440 0x708 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_06_GPIO_MUX4_IO27			0x1FC 0x440 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_06_SRC_BT_CFG00			0x1FC 0x440 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_06_ENET_QOS_TX_DATA03		0x1FC 0x440 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_06_LPSPI3_SOUT			0x1FC 0x440 0x608 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_06_GPIO10_IO27			0x1FC 0x440 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_07_VIDEO_MUX_LCDIF_DATA03		0x200 0x444 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_07_ENET_1G_TX_DATA02		0x200 0x444 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_07_LPUART4_RTS_B			0x200 0x444 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_07_TMR3_TIMER1			0x200 0x444 0x658 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_07_XBAR1_INOUT33			0x200 0x444 0x70C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_07_GPIO_MUX4_IO28			0x200 0x444 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_07_SRC_BT_CFG01			0x200 0x444 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_07_ENET_QOS_TX_DATA02		0x200 0x444 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_07_LPSPI3_PCS0			0x200 0x444 0x5F0 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_07_GPIO10_IO28			0x200 0x444 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_08_GPIO10_IO29			0x204 0x448 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_08_VIDEO_MUX_LCDIF_DATA04		0x204 0x448 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_08_ENET_1G_TX_DATA01		0x204 0x448 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_08_USDHC1_CD_B			0x204 0x448 0x6C8 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_08_TMR3_TIMER2			0x204 0x448 0x65C 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_08_XBAR1_INOUT34			0x204 0x448 0x710 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_08_GPIO_MUX4_IO29			0x204 0x448 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_08_SRC_BT_CFG02			0x204 0x448 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_08_ENET_QOS_TX_DATA01		0x204 0x448 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_08_LPSPI3_PCS1			0x204 0x448 0x5F4 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_09_VIDEO_MUX_LCDIF_DATA05		0x208 0x44C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_09_ENET_1G_TX_DATA00		0x208 0x44C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_09_USDHC1_WP			0x208 0x44C 0x6CC 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_09_TMR4_TIMER0			0x208 0x44C 0x660 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_09_XBAR1_INOUT35			0x208 0x44C 0x714 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_09_GPIO_MUX4_IO30			0x208 0x44C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_09_SRC_BT_CFG03			0x208 0x44C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_09_ENET_QOS_TX_DATA00		0x208 0x44C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_09_LPSPI3_PCS2			0x208 0x44C 0x5F8 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_09_GPIO10_IO30			0x208 0x44C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_10_VIDEO_MUX_LCDIF_DATA06		0x20C 0x450 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_10_ENET_1G_TX_EN			0x20C 0x450 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_10_USDHC1_RESET_B			0x20C 0x450 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_10_TMR4_TIMER1			0x20C 0x450 0x664 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_10_XBAR1_INOUT36			0x20C 0x450 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B1_10_GPIO_MUX4_IO31			0x20C 0x450 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_10_SRC_BT_CFG04			0x20C 0x450 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_10_ENET_QOS_TX_EN			0x20C 0x450 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_10_LPSPI3_PCS3			0x20C 0x450 0x5FC 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_10_GPIO10_IO31			0x20C 0x450 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_11_VIDEO_MUX_LCDIF_DATA07		0x210 0x454 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_1G_TX_CLK_IO		0x210 0x454 0x4E8 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_11_ENET_1G_REF_CLK			0x210 0x454 0x4C4 0x2 0x2
+#define IOMUXC_GPIO_DISP_B1_11_TMR4_TIMER2			0x210 0x454 0x668 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_11_XBAR1_INOUT37			0x210 0x454 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B1_11_GPIO_MUX5_IO00			0x210 0x454 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_11_SRC_BT_CFG05			0x210 0x454 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_QOS_TX_CLK			0x210 0x454 0x4A4 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_QOS_REF_CLK			0x210 0x454 0x4A0 0x9 0x2
+#define IOMUXC_GPIO_DISP_B1_11_GPIO11_IO00			0x210 0x454 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_00_GPIO11_IO01			0x214 0x458 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_00_VIDEO_MUX_LCDIF_DATA08		0x214 0x458 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_00_WDOG1_B				0x214 0x458 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_00_MQS_RIGHT			0x214 0x458 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_00_ENET_1G_TX_ER			0x214 0x458 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_00_SAI1_TX_DATA03			0x214 0x458 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_00_GPIO_MUX5_IO01			0x214 0x458 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_00_SRC_BT_CFG06			0x214 0x458 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_00_ENET_QOS_TX_ER			0x214 0x458 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_01_VIDEO_MUX_LCDIF_DATA09		0x218 0x45C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_01_USDHC1_VSELECT			0x218 0x45C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_01_MQS_LEFT				0x218 0x45C 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_01_WDOG2_B				0x218 0x45C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_01_SAI1_TX_DATA02			0x218 0x45C 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_01_GPIO_MUX5_IO02			0x218 0x45C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_01_SRC_BT_CFG07			0x218 0x45C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_01_EWM_OUT_B			0x218 0x45C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_01_CCM_ENET_REF_CLK_25M		0x218 0x45C 0x0 0x9 0x0
+#define IOMUXC_GPIO_DISP_B2_01_GPIO11_IO02			0x218 0x45C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_02_GPIO11_IO03			0x21C 0x460 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_02_VIDEO_MUX_LCDIF_DATA10		0x21C 0x460 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ENET_TX_DATA00			0x21C 0x460 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_02_PIT1_TRIGGER3			0x21C 0x460 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ARM_TRACE00			0x21C 0x460 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_02_SAI1_TX_DATA01			0x21C 0x460 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_02_GPIO_MUX5_IO03			0x21C 0x460 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_02_SRC_BT_CFG08			0x21C 0x460 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ENET_QOS_TX_DATA00		0x21C 0x460 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_03_GPIO11_IO04			0x220 0x464 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_03_VIDEO_MUX_LCDIF_DATA11		0x220 0x464 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ENET_TX_DATA01			0x220 0x464 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_03_PIT1_TRIGGER2			0x220 0x464 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ARM_TRACE01			0x220 0x464 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_03_SAI1_MCLK			0x220 0x464 0x66C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_03_GPIO_MUX5_IO04			0x220 0x464 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_03_SRC_BT_CFG09			0x220 0x464 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ENET_QOS_TX_DATA01		0x220 0x464 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_04_VIDEO_MUX_LCDIF_DATA12		0x224 0x468 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ENET_TX_EN			0x224 0x468 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_04_PIT1_TRIGGER1			0x224 0x468 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ARM_TRACE02			0x224 0x468 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_04_SAI1_RX_SYNC			0x224 0x468 0x678 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_04_GPIO_MUX5_IO05			0x224 0x468 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_04_SRC_BT_CFG10			0x224 0x468 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ENET_QOS_TX_EN			0x224 0x468 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_04_GPIO11_IO05			0x224 0x468 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_05_GPIO11_IO06			0x228 0x46C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_05_VIDEO_MUX_LCDIF_DATA13		0x228 0x46C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_05_ENET_TX_CLK			0x228 0x46C 0x4C0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_05_ENET_REF_CLK			0x228 0x46C 0x4A8 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_05_ARM_TRACE03			0x228 0x46C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_05_SAI1_RX_BCLK			0x228 0x46C 0x670 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_05_GPIO_MUX5_IO06			0x228 0x46C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_05_SRC_BT_CFG11			0x228 0x46C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_05_ENET_QOS_TX_CLK			0x228 0x46C 0x4A4 0x8 0x1
+
+#define IOMUXC_GPIO_DISP_B2_06_GPIO11_IO07			0x22C 0x470 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_06_VIDEO_MUX_LCDIF_DATA14		0x22C 0x470 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_06_ENET_RX_DATA00			0x22C 0x470 0x4B0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_06_LPUART7_TXD			0x22C 0x470 0x630 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_06_ARM_TRACE_CLK			0x22C 0x470 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_06_SAI1_RX_DATA00			0x22C 0x470 0x674 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_06_GPIO_MUX5_IO07			0x22C 0x470 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_06_ENET_QOS_RX_DATA00		0x22C 0x470 0x4F0 0x8 0x1
+
+#define IOMUXC_GPIO_DISP_B2_07_VIDEO_MUX_LCDIF_DATA15		0x230 0x474 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_07_ENET_RX_DATA01			0x230 0x474 0x4B4 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_07_LPUART7_RXD			0x230 0x474 0x62C 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_07_ARM_TRACE_SWO			0x230 0x474 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_07_SAI1_TX_DATA00			0x230 0x474 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_07_GPIO_MUX5_IO08			0x230 0x474 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_07_ENET_QOS_RX_DATA01		0x230 0x474 0x4F4 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_07_GPIO11_IO08			0x230 0x474 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_08_GPIO11_IO09			0x234 0x478 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_08_VIDEO_MUX_LCDIF_DATA16		0x234 0x478 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_08_ENET_RX_EN			0x234 0x478 0x4B8 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_08_LPUART8_TXD			0x234 0x478 0x638 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_08_ARM_CM7_EVENTO			0x234 0x478 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_08_SAI1_TX_BCLK			0x234 0x478 0x67C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_08_GPIO_MUX5_IO09			0x234 0x478 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_08_ENET_QOS_RX_EN			0x234 0x478 0x4F8 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_08_LPUART1_TXD			0x234 0x478 0x620 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_09_GPIO11_IO10			0x238 0x47C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_09_VIDEO_MUX_LCDIF_DATA17		0x238 0x47C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_09_ENET_RX_ER			0x238 0x47C 0x4BC 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_09_LPUART8_RXD			0x238 0x47C 0x634 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_09_ARM_CM7_EVENTI			0x238 0x47C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_09_SAI1_TX_SYNC			0x238 0x47C 0x680 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_09_GPIO_MUX5_IO10			0x238 0x47C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_09_ENET_QOS_RX_ER			0x238 0x47C 0x4FC 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_09_LPUART1_RXD			0x238 0x47C 0x61C 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_10_GPIO11_IO11			0x23C 0x480 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_10_VIDEO_MUX_LCDIF_DATA18		0x23C 0x480 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_10_EMVSIM2_IO			0x23C 0x480 0x6A8 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_10_LPUART2_TXD			0x23C 0x480 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_10_WDOG2_RESET_B_DEB		0x23C 0x480 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_10_XBAR1_INOUT38			0x23C 0x480 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_10_GPIO_MUX5_IO11			0x23C 0x480 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_10_LPI2C3_SCL			0x23C 0x480 0x5BC 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_10_ENET_QOS_RX_ER			0x23C 0x480 0x4FC 0x8 0x2
+#define IOMUXC_GPIO_DISP_B2_10_SPDIF_IN				0x23C 0x480 0x6B4 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_11_VIDEO_MUX_LCDIF_DATA19		0x240 0x484 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_11_EMVSIM2_CLK			0x240 0x484 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_11_LPUART2_RXD			0x240 0x484 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_11_WDOG1_RESET_B_DEB		0x240 0x484 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_11_XBAR1_INOUT39			0x240 0x484 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_11_GPIO_MUX5_IO12			0x240 0x484 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_11_LPI2C3_SDA			0x240 0x484 0x5C0 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_11_ENET_QOS_CRS			0x240 0x484 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_11_SPDIF_OUT			0x240 0x484 0x0 0x9 0x0
+#define IOMUXC_GPIO_DISP_B2_11_GPIO11_IO12			0x240 0x484 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_12_GPIO11_IO13			0x244 0x488 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_12_VIDEO_MUX_LCDIF_DATA20		0x244 0x488 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_12_EMVSIM2_RST			0x244 0x488 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_12_FLEXCAN1_TX			0x244 0x488 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPUART2_CTS_B			0x244 0x488 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_12_XBAR1_INOUT40			0x244 0x488 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_12_GPIO_MUX5_IO13			0x244 0x488 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPI2C4_SCL			0x244 0x488 0x5C4 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_12_ENET_QOS_COL			0x244 0x488 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPSPI4_SCK			0x244 0x488 0x610 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B2_13_GPIO11_IO14			0x248 0x48C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_13_VIDEO_MUX_LCDIF_DATA21		0x248 0x48C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_13_EMVSIM2_SVEN			0x248 0x48C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_13_FLEXCAN1_RX			0x248 0x48C 0x498 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_13_LPUART2_RTS_B			0x248 0x48C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_13_ENET_REF_CLK			0x248 0x48C 0x4A8 0x4 0x2
+#define IOMUXC_GPIO_DISP_B2_13_GPIO_MUX5_IO14			0x248 0x48C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_13_LPI2C4_SDA			0x248 0x48C 0x5C8 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_13_ENET_QOS_1588_EVENT0_OUT		0x248 0x48C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_13_LPSPI4_SIN			0x248 0x48C 0x614 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B2_14_GPIO_MUX5_IO15			0x24C 0x490 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_14_FLEXCAN1_TX			0x24C 0x490 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_14_ENET_QOS_1588_EVENT0_IN		0x24C 0x490 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_14_LPSPI4_SOUT			0x24C 0x490 0x618 0x9 0x1
+#define IOMUXC_GPIO_DISP_B2_14_GPIO11_IO15			0x24C 0x490 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_14_VIDEO_MUX_LCDIF_DATA22		0x24C 0x490 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_14_EMVSIM2_PD			0x24C 0x490 0x6AC 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_14_WDOG2_B				0x24C 0x490 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_14_VIDEO_MUX_EXT_DCIC1		0x24C 0x490 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_14_ENET_1G_REF_CLK			0x24C 0x490 0x4C4 0x4 0x3
+
+#define IOMUXC_GPIO_DISP_B2_15_VIDEO_MUX_LCDIF_DATA23		0x250 0x494 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_15_EMVSIM2_POWER_FAIL		0x250 0x494 0x6B0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_15_WDOG1_B				0x250 0x494 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_15_VIDEO_MUX_EXT_DCIC2		0x250 0x494 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_15_PIT1_TRIGGER0			0x250 0x494 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_15_GPIO_MUX5_IO16			0x250 0x494 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_15_FLEXCAN1_RX			0x250 0x494 0x498 0x6 0x2
+#define IOMUXC_GPIO_DISP_B2_15_ENET_QOS_1588_EVENT0_AUX_IN	0x250 0x494 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_15_LPSPI4_PCS0			0x250 0x494 0x60C 0x9 0x1
+#define IOMUXC_GPIO_DISP_B2_15_GPIO11_IO16			0x250 0x494 0x0 0xA 0x0
+
+#endif  /* _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H */
diff --git a/arch/arm/boot/dts/nxp/imx/mba6ulx.dtsi b/arch/arm/boot/dts/nxp/imx/mba6ulx.dtsi
new file mode 100644
index 000000000000..e78d0a7d8cd2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/mba6ulx.dtsi
@@ -0,0 +1,575 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/ {
+	model = "TQ-Systems MBA6ULx Baseboard";
+
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc1;
+		rtc0 = &rtc0;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&reg_mba6ul_3v3>;
+		enable-gpios = <&expander_out0 4 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	beeper: beeper {
+		compatible = "gpio-beeper";
+		gpios = <&expander_out1 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_buttons: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_buttons>;
+
+		button-1 {
+			label = "s14";
+			linux,code = <KEY_1>;
+			gpios = <&expander_in0 0 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-2 {
+			label = "s6";
+			linux,code = <KEY_2>;
+			gpios = <&expander_in0 1 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-3 {
+			label = "s7";
+			linux,code = <KEY_3>;
+			gpios = <&expander_in0 2 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		power-button {
+			label = "POWER";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led1 {
+			label = "led1";
+			gpios = <&expander_out1 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&expander_out1 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_lcd_pwr: regulator-lcd-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-pwr";
+		gpio = <&expander_out0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_mba6ul_3v3: regulator-mba6ul-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6ul-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_mba6ul_5v0: regulator-mba6ul-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6ul-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_mpcie: regulator-mpcie-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "mpcie-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&expander_out0 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		startup-delay-us = <500000>;
+		vin-supply = <&reg_mba6ul_3v3>;
+	};
+
+	reg_otg2vbus_5v0: regulator-otg2-vbus-5v0 {
+		compatible = "regulator-fixed";
+		gpio = <&expander_out1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "otg2-vbus-supply-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_mpcie>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x6000000>;
+			linux,cma-default;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "imx-audio-tlv320aic32x4";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+		audio-asrc = <&asrc>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_mba6ul_3v3>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_mba6ul_3v3>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <768000000>;
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <1>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_mba6ul_3v3>;
+	phy-reset-gpios = <&expander_out1 1 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-reset-post-delay = <1>;
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_mdc>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_mba6ul_3v3>;
+	phy-reset-gpios = <&expander_out1 2 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-reset-post-delay = <1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			reg = <0>;
+			max-speed = <100>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+			reg = <1>;
+			max-speed = <100>;
+		};
+	};
+};
+
+&i2c4 {
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&clks IMX6UL_CLK_SAI1>;
+		clock-names = "mclk";
+		ldoin-supply = <&reg_mba6ul_3v3>;
+		iov-supply = <&reg_mba6ul_3v3>;
+	};
+
+	jc42: temperature-sensor@19 {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x19>;
+	};
+
+	expander_out0: gpio-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+	};
+
+	expander_in0: gpio-expander@21 {
+		compatible = "nxp,pca9554";
+		reg = <0x21>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander_in0>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+
+		enet1_int-hog {
+			gpio-hog;
+			gpios = <6 0>;
+			input;
+		};
+
+		enet2_int-hog {
+			gpio-hog;
+			gpios = <7 0>;
+			input;
+		};
+	};
+
+	expander_out1: gpio-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+	};
+
+	analog_touch: touchscreen@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpio4>;
+		status = "disabled";
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			st,adc-freq = <1>;      /* 3.25 MHz ADC clock speed */
+			st,ave-ctrl = <3>;      /* 8 sample average control */
+			st,fraction-z = <7>;    /* 7 length fractional part in z */
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			st,mod-12b = <1>;       /* 12-bit ADC */
+			st,ref-sel = <0>;       /* internal ADC reference */
+			st,sample-time = <4>;   /* ADC converstion time: 80 clocks */
+			st,settling = <3>;      /* 1 ms panel driver settling time */
+			st,touch-det-delay = <5>; /* 5 ms touch detect interrupt delay */
+		};
+	};
+
+	/* NXP SE97BTP with temperature sensor + eeprom */
+	se97b: eeprom@51 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&clks IMX6UL_CLK_SAI1_SEL>,
+			  <&clks IMX6UL_CLK_SAI1>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <24000000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode; */
+	/* pinctrl-0 = <&pinctrl_uart6dte>; */
+	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+/* otg-port */
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	power-active-high;
+	over-current-active-low;
+	/* we implement only dual role but not a fully featured OTG */
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+/* 7-port usb hub */
+/* id, pwr, oc pins not connected */
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_otg2vbus_5v0>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_mba6ul_3v3>;
+	vqmmc-supply = <&reg_vccsd>;
+	no-1-8-v;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_buttons: buttonsgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x100b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK	0x1b020
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO	0x1b020
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI	0x1b020
+			MX6UL_PAD_UART4_RX_DATA__ECSPI2_SS0	0x1b020
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0a0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0a0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet2_mdc: enet2mdcgrp {
+		fsl,pins = <
+			/* mdio */
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+		>;
+	};
+
+	pinctrl_expander_in0: expanderin0grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x1b0b1
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT		0x00003050
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK	0x1b0b1
+			MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC	0x1b0b1
+			MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA	0x1f0b8
+			MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA	0x110b0
+			MX6UL_PAD_CSI_DATA01__SAI1_MCLK		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6dte: uart6dte {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__UART6_DTE_TX	0x1b0b1
+			MX6UL_PAD_CSI_MCLK__UART6_DTE_RX	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DTE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DTE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x00017059
+			MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC	0x0001b0b0
+			MX6UL_PAD_GPIO1_IO04__USB_OTG1_PWR	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x00017059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x00017059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x00017059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x00017059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x00017059
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x000170b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x000170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x000170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x000170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x000170b9
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x000170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x000170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x000170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x000170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x000170f9
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_wdog1: wdog1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B	0x0001b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/lpc/Makefile b/arch/arm/boot/dts/nxp/lpc/Makefile
new file mode 100644
index 000000000000..56b9a0ebb917
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/lpc/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_LPC18XX) += \
+	lpc4337-ciaa.dtb \
+	lpc4350-hitex-eval.dtb \
+	lpc4357-ea4357-devkit.dtb \
+	lpc4357-myd-lpc4357.dtb
+dtb-$(CONFIG_ARCH_LPC32XX) += \
+	lpc3250-ea3250.dtb \
+	lpc3250-phy3250.dtb
diff --git a/arch/arm/boot/dts/lpc18xx.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc18xx.dtsi
index 10b8249b8ab6..6dd73290f0c6 100644
--- a/arch/arm/boot/dts/lpc18xx.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc18xx.dtsi
@@ -11,7 +11,7 @@
  *
  */
 
-#include "armv7-m.dtsi"
+#include "../../armv7-m.dtsi"
 
 #include "dt-bindings/clock/lpc18xx-cgu.h"
 #include "dt-bindings/clock/lpc18xx-ccu.h"
@@ -74,7 +74,7 @@
 		sct_pwm: pwm@40000000 {
 			compatible = "nxp,lpc1850-sct-pwm";
 			reg = <0x40000000 0x1000>;
-			clocks =<&ccu1 CLK_CPU_SCT>;
+			clocks = <&ccu1 CLK_CPU_SCT>;
 			clock-names = "pwm";
 			resets = <&rgu 37>;
 			#pwm-cells = <3>;
@@ -121,7 +121,7 @@
 			status = "disabled";
 		};
 
-		usb0: ehci@40006100 {
+		usb0: usb@40006100 {
 			compatible = "nxp,lpc1850-ehci", "generic-ehci";
 			reg = <0x40006100 0x100>;
 			interrupts = <8>;
@@ -133,7 +133,7 @@
 			status = "disabled";
 		};
 
-		usb1: ehci@40007100 {
+		usb1: usb@40007100 {
 			compatible = "nxp,lpc1850-ehci", "generic-ehci";
 			reg = <0x40007100 0x100>;
 			interrupts = <9>;
@@ -183,7 +183,7 @@
 			compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
 			reg = <0x40010000 0x2000>;
 			interrupts = <5>;
-			interrupt-names	= "macirq";
+			interrupt-names = "macirq";
 			clocks = <&ccu1 CLK_CPU_ETHERNET>;
 			clock-names = "stmmaceth";
 			resets = <&rgu 22>;
diff --git a/arch/arm/boot/dts/lpc3250-ea3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
index 63c6f17bb7c9..63c6f17bb7c9 100644
--- a/arch/arm/boot/dts/lpc3250-ea3250.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
diff --git a/arch/arm/boot/dts/lpc3250-phy3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
index 21a6d0bca1e8..21a6d0bca1e8 100644
--- a/arch/arm/boot/dts/lpc3250-phy3250.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc32xx.dtsi
index 7b7ec7b1217b..974410918f35 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc32xx.dtsi
@@ -123,7 +123,6 @@
 				clocks = <&usbclk LPC32XX_USB_CLK_I2C>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				pnx,timeout = <0x64>;
 			};
 
 			usbclk: clock-controller@f00 {
@@ -286,7 +285,6 @@
 				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				pnx,timeout = <0x64>;
 				clocks = <&clk LPC32XX_CLK_I2C1>;
 			};
 
@@ -297,7 +295,6 @@
 				interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				pnx,timeout = <0x64>;
 				clocks = <&clk LPC32XX_CLK_I2C2>;
 			};
 
@@ -318,7 +315,7 @@
 			/* System Control Block */
 			scb {
 				compatible = "simple-bus";
-				ranges = <0x0 0x040004000 0x00001000>;
+				ranges = <0x0 0x40004000 0x00001000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 
@@ -329,9 +326,6 @@
 
 					clocks = <&xtal_32k>, <&xtal>;
 					clock-names = "xtal_32k", "xtal";
-
-					assigned-clocks = <&clk LPC32XX_CLK_HCLK_PLL>;
-					assigned-clock-rates = <208000000>;
 				};
 			};
 
diff --git a/arch/arm/boot/dts/lpc4337-ciaa.dts b/arch/arm/boot/dts/nxp/lpc/lpc4337-ciaa.dts
index beddaba85393..beddaba85393 100644
--- a/arch/arm/boot/dts/lpc4337-ciaa.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4337-ciaa.dts
diff --git a/arch/arm/boot/dts/lpc4350-hitex-eval.dts b/arch/arm/boot/dts/nxp/lpc/lpc4350-hitex-eval.dts
index 93d0c2e99e7c..93d0c2e99e7c 100644
--- a/arch/arm/boot/dts/lpc4350-hitex-eval.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4350-hitex-eval.dts
diff --git a/arch/arm/boot/dts/lpc4350.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc4350.dtsi
index c4422f587055..c4422f587055 100644
--- a/arch/arm/boot/dts/lpc4350.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4350.dtsi
diff --git a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts b/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
index 224f80a4a31d..224f80a4a31d 100644
--- a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
diff --git a/arch/arm/boot/dts/lpc4357-myd-lpc4357.dts b/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
index 1f84654df50c..1f84654df50c 100644
--- a/arch/arm/boot/dts/lpc4357-myd-lpc4357.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
diff --git a/arch/arm/boot/dts/lpc4357.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc4357.dtsi
index 72f12db8d53a..72f12db8d53a 100644
--- a/arch/arm/boot/dts/lpc4357.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4357.dtsi
diff --git a/arch/arm/boot/dts/nxp/ls/Makefile b/arch/arm/boot/dts/nxp/ls/Makefile
new file mode 100644
index 000000000000..14759331dba2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_LS1021A) += \
+	ls1021a-iot.dtb \
+	ls1021a-moxa-uc-8410a.dtb \
+	ls1021a-qds.dtb \
+	ls1021a-tqmls1021a-mbls1021a.dtb \
+	ls1021a-tsn.dtb \
+	ls1021a-twr.dtb
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-iot.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-iot.dts
new file mode 100644
index 000000000000..e13ccae629a7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-iot.dts
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021-2022 NXP
+ *
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+	model = "LS1021A-IOT Board";
+	compatible = "fsl,ls1021a-iot", "fsl,ls1021a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	reg_3p3v: regulator-3V3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_2p5v: regulator-2V5 {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			frame-master;
+			bitclock-master;
+		};
+	};
+};
+
+&can0 {
+	status = "disabled";
+};
+
+&can1 {
+	status = "disabled";
+};
+
+&can2 {
+	status = "disabled";
+};
+
+&can3 {
+	status = "okay";
+};
+
+&dcu {
+	display = <&display>;
+	status = "okay";
+
+	display: display@0 {
+		bits-per-pixel = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+
+			timing0: mode0 {
+				clock-frequency = <25000000>;
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <80>;
+				hfront-porch = <80>;
+				vback-porch = <16>;
+				vfront-porch = <16>;
+				hsync-len = <12>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
+
+&enet0 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy1>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy3>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet2 {
+	fixed-link = <0 1 1000 0 0>;
+	phy-connection-type = "rgmii-id";
+	status = "okay";
+};
+
+&esdhc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9555: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sgtl5000: audio-codec@2a {
+		#sound-dai-cells = <0x0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0x2a>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_2p5v>;
+		clocks = <&sys_mclk>;
+	};
+
+	max1239: adc@35 {
+		compatible = "maxim,max1239";
+		reg = <0x35>;
+		#io-channel-cells = <1>;
+	};
+
+	ina2201: core-monitor@44 {
+		compatible = "ti,ina220";
+		reg = <0x44>;
+		shunt-resistor = <1000>;
+	};
+
+	ina2202: current-monitor@45 {
+		compatible = "ti,ina220";
+		reg = <0x45>;
+		shunt-resistor = <1000>;
+	};
+
+	lm75b: thermal-monitor@48 {
+		compatible = "national,lm75b";
+		reg = <0x48>;
+	};
+};
+
+&lpuart0 {
+	status = "okay";
+};
+
+&mdio0 {
+	phy0: ethernet-phy@0 {
+		reg = <0x0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <0x1>;
+	};
+
+	phy2: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
+	phy3: ethernet-phy@3 {
+		reg = <0x3>;
+	};
+
+	tbi1: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&qspi {
+	num-cs = <2>;
+	status = "okay";
+
+	s25fl128s: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
index f3ddea934f1b..d2cae8c7d7a6 100644
--- a/arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
@@ -30,11 +30,11 @@
 	};
 
 	reg_3p3v: regulator-3p3v {
-		  compatible = "regulator-fixed";
-		  regulator-name = "3P3V";
-		  regulator-min-microvolt = <3300000>;
-		  regulator-max-microvolt = <3300000>;
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	leds {
diff --git a/arch/arm/boot/dts/ls1021a-qds.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-qds.dts
index 74a67604876c..f1acb97aee69 100644
--- a/arch/arm/boot/dts/ls1021a-qds.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-qds.dts
@@ -1,49 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright 2013-2014 Freescale Semiconductor, Inc.
  * Copyright 2018 NXP
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -67,19 +25,12 @@
 		clock-frequency = <24576000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	sound {
@@ -231,9 +182,9 @@
 	#address-cells = <2>;
 	#size-cells = <1>;
 	/* NOR, NAND Flashes and FPGA on board */
-	ranges = <0x0 0x0 0x0 0x60000000 0x08000000
-		  0x2 0x0 0x0 0x7e800000 0x00010000
-		  0x3 0x0 0x0 0x7fb00000 0x00000100>;
+	ranges = <0x0 0x0 0x0 0x60000000 0x08000000>,
+		 <0x2 0x0 0x0 0x7e800000 0x00010000>,
+		 <0x3 0x0 0x0 0x7fb00000 0x00000100>;
 	status = "okay";
 
 	nor@0,0 {
@@ -254,7 +205,7 @@
 	fpga: board-control@3,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "simple-bus";
+		compatible = "simple-mfd";
 		reg = <0x3 0x0 0x0000100>;
 		bank-width = <1>;
 		device-width = <1>;
@@ -328,6 +279,20 @@
 	};
 };
 
+&qspi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+	};
+};
+
 &sai2 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
new file mode 100644
index 000000000000..34636fcdfd6a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+#include "ls1021a-tqmls1021a.dtsi"
+
+/ {
+	model = "TQMLS102xA SOM on MBLS102xA";
+	compatible = "tq,ls1021a-tqmls1021a-mbls102xa", "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+	audio_mclk: audio-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	backlight_dcu: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&pca9530 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		switch-1 {
+			label = "S6";
+			linux,code = <BTN_0>;
+			gpios = <&pca9554_0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		btn2: switch-2 {
+			label = "S7";
+			linux,code = <BTN_1>;
+			gpios = <&pca9554_0 1 GPIO_ACTIVE_LOW>;
+		};
+
+		switch-3 {
+			label = "S8";
+			linux,code = <BTN_2>;
+			gpios = <&pca9554_0 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_leds: gpio-leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <0>;
+			gpios = <&pca9554_2 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <1>;
+			gpios = <&pca9554_2 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <2>;
+			gpios = <&pca9554_2 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			function-enumerator = <0>;
+			gpios = <&pca9554_2 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	lvds_encoder: lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+		power-supply = <&reg_3p3v>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_in: endpoint {};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_out: endpoint {};
+			};
+		};
+	};
+
+	reg_1p2v: regulator-1p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P2V";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_3p3v>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	hdmi_out: hdmi {
+		compatible = "hdmi-connector";
+		type = "a";
+		ddc-i2c-bus = <&i2c0>;
+		status = "disabled";
+
+		port {
+			hdmi_in: endpoint {
+				remote-endpoint = <&sii9022a_out>;
+			};
+		};
+	};
+
+	display: panel {
+		backlight = <&backlight_dcu>;
+		enable-gpios = <&pca9554_1 3 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			panel_in: endpoint {};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "ls1021a-mbls1021a-tlv320aic32";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+	};
+
+};
+
+&can0 {
+	xceiver-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&can1 {
+	xceiver-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&dspi0 {
+	status = "okay";
+};
+
+&enet0 {
+	phy-handle = <&rgmii_phy0c>;
+	phy-mode = "rgmii-id";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&sgmii_phy03>;
+	phy-mode = "sgmii";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&enet2 {
+	phy-handle = <&rgmii_phy04>;
+	phy-mode = "rgmii-id";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&audio_mclk>;
+		clock-names = "mclk";
+		ldoin-supply = <&reg_3p3v>;
+		iov-supply = <&reg_3p3v>;
+	};
+
+	pca9554_0: gpio-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "BUTTON0", "BUTTON1",
+				  "BUTTON2", "EMMC_SEL",
+				  "DIP2", "DIP3",
+				  "EXT_TOUCH_INT", "GPIO_1";
+	};
+
+	pca9554_1: gpio-expander@21 {
+		compatible = "nxp,pca9554";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "PCIE_PWR_EN", "MPCIE_DISABLE#",
+				  "MPCIE_WAKE#", "LCD_BLT_EN",
+				  "LCD_PWR_EN", "EC1_PHY_PWDN",
+				  "EC3_PHY_PWDN", "SGMII_PHY_PWDN";
+	};
+
+	pca9554_2: gpio-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&extirq>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "MUX_SEL0", "MUX_SEL1",
+				  "MUX_SEL2", "MUX_SEL3",
+				  "V95", "V96", "V97", "V98";
+	};
+
+	sii9022a: hdmi-transmitter@3b {
+		compatible = "sil,sii9022";
+		reg = <0x3b>;
+		iovcc-supply = <&reg_3p3v>;
+		cvcc12-supply = <&reg_1p2v>;
+		interrupts = <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>;
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = <0>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022a_in: endpoint {};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022a_out: endpoint {
+					remote-endpoint = <&hdmi_in>;
+				};
+			};
+		};
+	};
+
+	stmpe811: port-expander@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&reg_3p3v>;
+		vio-supply = <&reg_3p3v>;
+
+		gpio {
+			compatible = "st,stmpe-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* GPIO 5-7 used for touch */
+			st,norequest-mask = <0xf0>;
+			gpio-line-names = "GPIO_ADC_I2C1_1",
+					  "GPIO_ADC_I2C1_2",
+					  "GPIO_ADC_I2C1_3",
+					  "GPIO_ADC_I2C1_4";
+		};
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			status = "disabled";
+		};
+	};
+
+	pca9530: leds@60 {
+		compatible = "nxp,pca9530";
+		reg = <0x60>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PWM_0", "PWM_1";
+
+		led-0 {
+			type = <PCA9532_TYPE_GPIO>;
+		};
+
+		led-1 {
+			type = <PCA9532_TYPE_GPIO>;
+		};
+	};
+
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&lpuart0 {
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&mdio0 {
+	sgmii_phy03: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x03>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+
+	rgmii_phy04: ethernet-phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x04>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+	};
+
+	rgmii_phy0c: ethernet-phy@c {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0c>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+	};
+};
+
+&pwm6 {
+	status = "okay";
+};
+
+&pwm7 {
+	status = "okay";
+};
+
+&sai1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb3 {
+	/*
+	 * Although DR connector, VBUS is always driven, so
+	 * restrict to host mode.
+	 */
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
new file mode 100644
index 000000000000..1b13851ad997
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include "ls1021a.dtsi"
+
+/ {
+	model = "TQMLS102xA SOM";
+	compatible = "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+	reg_3p3v_som: regulator-3p3v-som {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V_SOM";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&esdhc {
+	/* e-MMC over 8 data lines */
+	bus-width = <8>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* MC34VR500 DC/DC regulator at 0x8, managed by PMIC */
+	/* On-board PMC at 0x11 */
+
+	sa56004: temperature-sensor@4c {
+		compatible = "nxp,sa56004";
+		reg = <0x4c>;
+		vcc-supply = <&reg_3p3v_som>;
+	};
+
+	rtc0: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
+	};
+
+	m24c64_54: eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+		pagesize = <32>;
+		read-only;
+		vcc-supply = <&reg_3p3v_som>;
+	};
+};
+
+&mdio0 {
+	tbi1: tbi-phy@8 {
+		reg = <0x8>;
+		device_type = "tbi-phy";
+	};
+};
+
+&qspi {
+	status = "okay";
+
+	qflash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			uboot@0 {
+				label = "U-Boot-PBL";
+				reg = <0x0 0xe0000>;
+			};
+
+			env@e0000 {
+				label = "U-Boot Environment";
+				reg = <0xe0000 0x10000>;
+			};
+
+			dtb@f0000 {
+				label = "DTB";
+				reg = <0xf0000 0x10000>;
+			};
+
+			linux@100000 {
+				label = "Linux";
+				reg = <0x100000 0x700000>;
+			};
+
+			rootfs@800000 {
+				label = "RootFS";
+				reg = <0x800000 0x3800000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-tsn.dts
index 5b7689094b70..1ea32fff4120 100644
--- a/arch/arm/boot/dts/ls1021a-tsn.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tsn.dts
@@ -8,6 +8,7 @@
 
 / {
 	model = "NXP LS1021A-TSN Board";
+	compatible = "fsl,ls1021a-tsn", "fsl,ls1021a";
 
 	sys_mclk: clock-mclk {
 		compatible = "fixed-clock";
@@ -90,6 +91,8 @@
 				/* Internal port connected to eth2 */
 				ethernet = <&enet2>;
 				phy-mode = "rgmii";
+				rx-internal-delay-ps = <0>;
+				tx-internal-delay-ps = <0>;
 				reg = <4>;
 
 				fixed-link {
@@ -136,7 +139,6 @@
 	/* 3 axis accelerometer */
 	accelerometer@1e {
 		compatible = "fsl,fxls8471";
-		position = <0>;
 		reg = <0x1e>;
 	};
 
@@ -203,11 +205,15 @@
 	/* AR8031 */
 	sgmii_phy1: ethernet-phy@1 {
 		reg = <0x1>;
+		/* SGMII1_PHY_INT_B: connected to IRQ2, active low */
+		interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
 	};
 
 	/* AR8031 */
 	sgmii_phy2: ethernet-phy@2 {
 		reg = <0x2>;
+		/* SGMII2_PHY_INT_B: connected to IRQ2, active low */
+		interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
 	};
 
 	/* BCM5464 quad PHY */
@@ -247,7 +253,7 @@
 
 	flash@0 {
 		/* Rev. A uses 64MB flash, Rev. B & C use 32MB flash */
-		compatible = "jedec,spi-nor", "s25fl256s1", "s25fl512s";
+		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-twr.dts
index 9b1fe99d55b1..f5c03871b205 100644
--- a/arch/arm/boot/dts/ls1021a-twr.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-twr.dts
@@ -1,49 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright 2013-2014 Freescale Semiconductor, Inc.
  * Copyright 2018 NXP
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -65,19 +23,12 @@
 		clock-frequency = <24576000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	sound {
@@ -242,6 +193,20 @@
         status = "okay";
 };
 
+&qspi {
+	status = "okay";
+
+	n25q128a130: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+	};
+};
+
 &sai1 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/nxp/ls/ls1021a.dtsi
index 2f6977ada447..d471cc5efa94 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a.dtsi
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright 2013-2014 Freescale Semiconductor, Inc.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -51,7 +9,6 @@
 / {
 	#address-cells = <2>;
 	#size-cells = <2>;
-	compatible = "fsl,ls1021a";
 	interrupt-parent = <&gic>;
 
 	aliases {
@@ -59,6 +16,7 @@
 		ethernet0 = &enet0;
 		ethernet1 = &enet1;
 		ethernet2 = &enet2;
+		rtc1 = &ftm_alarm0;
 		serial0 = &lpuart0;
 		serial1 = &lpuart1;
 		serial2 = &lpuart2;
@@ -89,7 +47,7 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x0>;
 	};
@@ -154,7 +112,7 @@
 			compatible = "fsl,ls1021a-msi";
 			reg = <0x0 0x1570e00 0x0 0x8>;
 			msi-controller;
-			interrupts =  <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		msi2: msi-controller@1570e08 {
@@ -164,15 +122,23 @@
 			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		ifc: ifc@1530000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@1530000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x1530000 0x0 0x10000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1021a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen 4 3>;
+			clock-names = "sfp";
 		};
 
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1021a-dcfg", "syscon";
-			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			reg = <0x0 0x1ee0000 0x0 0x1000>;
 			big-endian;
 		};
 
@@ -181,7 +147,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x1550000 0x0 0x10000>,
-			      <0x0 0x40000000 0x0 0x40000000>;
+			      <0x0 0x40000000 0x0 0x20000000>;
 			reg-names = "QuadSPI", "QuadSPI-memory";
 			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "qspi_en", "qspi";
@@ -216,6 +182,25 @@
 			compatible = "fsl,ls1021a-scfg", "syscon";
 			reg = <0x0 0x1570000 0x0 0x10000>;
 			big-endian;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x1570000 0x10000>;
+
+			extirq: interrupt-controller@1ac {
+				compatible = "fsl,ls1021a-extirq";
+				#interrupt-cells = <2>;
+				#address-cells = <0>;
+				interrupt-controller;
+				reg = <0x1ac 4>;
+				interrupt-map =
+					<0 0 &gic GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0x7 0x0>;
+			};
 		};
 
 		crypto: crypto@1700000 {
@@ -226,6 +211,7 @@
 			reg		 = <0x0 0x1700000 0x0 0x100000>;
 			ranges		 = <0x0 0x0 0x1700000 0x100000>;
 			interrupts	 = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
 
 			sec_jr0: jr@10000 {
 				compatible = "fsl,sec-v5.0-job-ring",
@@ -268,82 +254,46 @@
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f00000 0x0 0x10000>;
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
-			fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x30061>;
-			fsl,tmu-calibration = <0x00000000 0x0000000f
-					       0x00000001 0x00000017
-					       0x00000002 0x0000001e
-					       0x00000003 0x00000026
-					       0x00000004 0x0000002e
-					       0x00000005 0x00000035
-					       0x00000006 0x0000003d
-					       0x00000007 0x00000044
-					       0x00000008 0x0000004c
-					       0x00000009 0x00000053
-					       0x0000000a 0x0000005b
-					       0x0000000b 0x00000064
-
-					       0x00010000 0x00000011
-					       0x00010001 0x0000001c
-					       0x00010002 0x00000024
-					       0x00010003 0x0000002b
-					       0x00010004 0x00000034
-					       0x00010005 0x00000039
-					       0x00010006 0x00000042
-					       0x00010007 0x0000004c
-					       0x00010008 0x00000051
-					       0x00010009 0x0000005a
-					       0x0001000a 0x00000063
-
-					       0x00020000 0x00000013
-					       0x00020001 0x00000019
-					       0x00020002 0x00000024
-					       0x00020003 0x0000002c
-					       0x00020004 0x00000035
-					       0x00020005 0x0000003d
-					       0x00020006 0x00000046
-					       0x00020007 0x00000050
-					       0x00020008 0x00000059
-
-					       0x00030000 0x00000002
-					       0x00030001 0x0000000d
-					       0x00030002 0x00000019
-					       0x00030003 0x00000024>;
+			fsl,tmu-range = <0xb0000 0x9002c 0x6004e 0x30066>;
+			fsl,tmu-calibration = <0x00000000 0x00000020>,
+					      <0x00000001 0x00000024>,
+					      <0x00000002 0x0000002a>,
+					      <0x00000003 0x00000032>,
+					      <0x00000004 0x00000038>,
+					      <0x00000005 0x0000003e>,
+					      <0x00000006 0x00000043>,
+					      <0x00000007 0x0000004a>,
+					      <0x00000008 0x00000050>,
+					      <0x00000009 0x00000059>,
+					      <0x0000000a 0x0000005f>,
+					      <0x0000000b 0x00000066>,
+
+					      <0x00010000 0x00000023>,
+					      <0x00010001 0x0000002b>,
+					      <0x00010002 0x00000033>,
+					      <0x00010003 0x0000003a>,
+					      <0x00010004 0x00000042>,
+					      <0x00010005 0x0000004a>,
+					      <0x00010006 0x00000054>,
+					      <0x00010007 0x0000005c>,
+					      <0x00010008 0x00000065>,
+					      <0x00010009 0x0000006f>,
+
+					      <0x00020000 0x00000029>,
+					      <0x00020001 0x00000033>,
+					      <0x00020002 0x0000003d>,
+					      <0x00020003 0x00000048>,
+					      <0x00020004 0x00000054>,
+					      <0x00020005 0x00000060>,
+					      <0x00020006 0x0000006c>,
+
+					      <0x00030000 0x00000025>,
+					      <0x00030001 0x00000033>,
+					      <0x00030002 0x00000043>,
+					      <0x00030003 0x00000055>;
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-
-				thermal-sensors = <&tmu 0>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-							<&cpu1 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		dspi0: spi@2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
@@ -376,10 +326,9 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2180000 0x0 0x10000>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
 			clocks = <&clockgen 4 1>;
-			dma-names = "tx", "rx";
-			dmas = <&edma0 1 39>, <&edma0 1 38>;
+			dma-names = "rx", "tx";
+			dmas = <&edma0 1 38>, <&edma0 1 39>;
 			status = "disabled";
 		};
 
@@ -389,10 +338,9 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2190000 0x0 0x10000>;
 			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
 			clocks = <&clockgen 4 1>;
-			dma-names = "tx", "rx";
-			dmas = <&edma0 1 37>, <&edma0 1 36>;
+			dma-names = "rx", "tx";
+			dmas = <&edma0 1 36>, <&edma0 1 37>;
 			status = "disabled";
 		};
 
@@ -402,10 +350,9 @@
 			#size-cells = <0>;
 			reg = <0x0 0x21a0000 0x0 0x10000>;
 			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
 			clocks = <&clockgen 4 1>;
-			dma-names = "tx", "rx";
-			dmas = <&edma0 1 35>, <&edma0 1 34>;
+			dma-names = "rx", "tx";
+			dmas = <&edma0 1 34>, <&edma0 1 35>;
 			status = "disabled";
 		};
 
@@ -700,7 +647,7 @@
 			status = "disabled";
 		};
 
-		edma0: edma@2c00000 {
+		edma0: dma-controller@2c00000 {
 			#dma-cells = <2>;
 			compatible = "fsl,vf610-edma";
 			reg = <0x0 0x2c00000 0x0 0x10000>,
@@ -728,7 +675,7 @@
 		};
 
 		mdio0: mdio@2d24000 {
-			compatible = "fsl,etsec2-mdio";
+			compatible = "gianfar";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -737,7 +684,7 @@
 		};
 
 		mdio1: mdio@2d64000 {
-			compatible = "fsl,etsec2-mdio";
+			compatible = "gianfar";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -753,7 +700,7 @@
 			fsl,tmr-prsc    = <2>;
 			fsl,tmr-add     = <0xaaaaaaab>;
 			fsl,tmr-fiper1  = <999999995>;
-			fsl,tmr-fiper2  = <99990>;
+			fsl,tmr-fiper2  = <999999995>;
 			fsl,max-adj     = <499999999>;
 			fsl,extts-fifo;
 		};
@@ -854,7 +801,7 @@
 			phy_type = "ulpi";
 		};
 
-		usb3: usb3@3100000 {
+		usb3: usb@3100000 {
 			compatible = "snps,dwc3";
 			reg = <0x0 0x3100000 0x0 0x10000>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
@@ -866,8 +813,8 @@
 
 		pcie@3400000 {
 			compatible = "fsl,ls1021a-pcie";
-			reg = <0x00 0x03400000 0x0 0x00010000   /* controller registers */
-			       0x40 0x00000000 0x0 0x00002000>; /* configuration space */
+			reg = <0x00 0x03400000 0x0 0x00010000>, /* controller registers */
+			      <0x40 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
 			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
 			fsl,pcie-scfg = <&scfg 0>;
@@ -876,8 +823,8 @@
 			device_type = "pci";
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
-			ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000   /* downstream I/O */
-				  0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000>, /* downstream I/O */
+				 <0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
 			msi-parent = <&msi1>, <&msi2>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
@@ -890,8 +837,8 @@
 
 		pcie@3500000 {
 			compatible = "fsl,ls1021a-pcie";
-			reg = <0x00 0x03500000 0x0 0x00010000   /* controller registers */
-			       0x48 0x00000000 0x0 0x00002000>; /* configuration space */
+			reg = <0x00 0x03500000 0x0 0x00010000>, /* controller registers */
+			      <0x48 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
 			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
 			fsl,pcie-scfg = <&scfg 1>;
@@ -900,8 +847,8 @@
 			device_type = "pci";
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
-			ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000   /* downstream I/O */
-				  0x82000000 0x0 0x40000000 0x48 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000>, /* downstream I/O */
+				 <0x82000000 0x0 0x40000000 0x48 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
 			msi-parent = <&msi1>, <&msi2>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
@@ -919,6 +866,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		can1: can@2a80000 {
@@ -928,6 +876,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		can2: can@2a90000 {
@@ -937,6 +886,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		can3: can@2aa0000 {
@@ -946,6 +896,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		ocram1: sram@10000000 {
@@ -974,6 +925,7 @@
 				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "qdma-error",
 				"qdma-queue0", "qdma-queue1";
+			#dma-cells = <2>;
 			dma-channels = <8>;
 			block-number = <1>;
 			block-offset = <0x1000>;
@@ -983,5 +935,53 @@
 			big-endian;
 		};
 
+		rcpm: power-controller@1ee2140 {
+			compatible = "fsl,ls1021a-rcpm", "fsl,qoriq-rcpm-2.1+";
+			reg = <0x0 0x1ee2140 0x0 0x8>;
+			#fsl,rcpm-wakeup-cells = <2>;
+			#power-domain-cells = <0>;
+		};
+
+		ftm_alarm0: timer0@29d0000 {
+			compatible = "fsl,ls1021a-ftm-alarm";
+			reg = <0x0 0x29d0000 0x0 0x10000>;
+			reg-names = "ftm";
+			fsl,rcpm-wakeup = <&rcpm 0x0 0x20000000>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			big-endian;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile b/arch/arm/boot/dts/nxp/mxs/Makefile
new file mode 100644
index 000000000000..a430d04f9c69
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/Makefile
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MXS) += \
+	imx23-evk.dtb \
+	imx23-olinuxino.dtb \
+	imx23-sansa.dtb \
+	imx23-stmp378x_devb.dtb \
+	imx23-xfi3.dtb \
+	imx28-apf28.dtb \
+	imx28-apf28dev.dtb \
+	imx28-apx4devkit.dtb \
+	imx28-cfa10036.dtb \
+	imx28-cfa10037.dtb \
+	imx28-cfa10049.dtb \
+	imx28-cfa10055.dtb \
+	imx28-cfa10056.dtb \
+	imx28-cfa10057.dtb \
+	imx28-cfa10058.dtb \
+	imx28-duckbill-2-485.dtb \
+	imx28-duckbill-2.dtb \
+	imx28-duckbill-2-enocean.dtb \
+	imx28-duckbill-2-spi.dtb \
+	imx28-duckbill.dtb \
+	imx28-eukrea-mbmx283lc.dtb \
+	imx28-eukrea-mbmx287lc.dtb \
+	imx28-evk.dtb \
+	imx28-m28cu3.dtb \
+	imx28-m28evk.dtb \
+	imx28-sps1.dtb \
+	imx28-ts4600.dtb \
+	imx28-tx28.dtb \
+	imx28-xea.dtb
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/nxp/mxs/imx23-evk.dts
index 0b2701ca2921..7365fe4581a3 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-evk.dts
@@ -53,7 +53,7 @@
 
 	apb@80000000 {
 		apbh@80000000 {
-			gpmi-nand@8000c000 {
+			nand-controller@8000c000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&gpmi_pins_a &gpmi_pins_fixup>;
 				status = "okay";
@@ -79,7 +79,6 @@
 						MX23_PAD_LCD_RESET__GPIO_1_18
 						MX23_PAD_PWM3__GPIO_1_29
 						MX23_PAD_PWM4__GPIO_1_30
-						MX23_PAD_SSP1_DETECT__SSP1_DETECT
 					>;
 					fsl,drive-strength = <MXS_DRIVE_4mA>;
 					fsl,voltage = <MXS_VOLTAGE_HIGH>;
@@ -138,7 +137,7 @@
 
 	backlight_display: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
+		pwms = <&pwm 2 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dts
index 4c9aafe00b5d..229e727b222e 100644
--- a/arch/arm/boot/dts/imx23-olinuxino.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dts
@@ -23,7 +23,7 @@
 			ssp0: spi@80010000 {
 				compatible = "fsl,imx23-mmc";
 				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
 				bus-width = <4>;
 				broken-cd;
 				status = "okay";
@@ -101,21 +101,14 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb0_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
-			gpio = <&gpio0 17 0>;
-		};
+	reg_usb0_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
+		gpio = <&gpio0 17 0>;
 	};
 
 	leds {
diff --git a/arch/arm/boot/dts/imx23-pinfunc.h b/arch/arm/boot/dts/nxp/mxs/imx23-pinfunc.h
index 5c0f32ca3a93..468c079f3c2b 100644
--- a/arch/arm/boot/dts/imx23-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX23 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MX23_PINCTRL_H__
diff --git a/arch/arm/boot/dts/imx23-sansa.dts b/arch/arm/boot/dts/nxp/mxs/imx23-sansa.dts
index 46057d9bf555..b23e7ada9c80 100644
--- a/arch/arm/boot/dts/imx23-sansa.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-sansa.dts
@@ -166,7 +166,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
+		pwms = <&pwm 2 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
@@ -175,10 +175,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio1 24 0		/* SDA */
-			&gpio1 22 0		/* SCL */
-		>;
+		sda-gpios = <&gpio1 24 0>;
+		scl-gpios = <&gpio1 22 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 
@@ -186,10 +184,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio0 31 0		/* SDA */
-			&gpio0 30 0		/* SCL */
-		>;
+		sda-gpios = <&gpio0 31 0>;
+		scl-gpios = <&gpio0 30 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 
 		touch: touch@20 {
diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/nxp/mxs/imx23-stmp378x_devb.dts
index da4b88f32eaa..69124ba6a666 100644
--- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-stmp378x_devb.dts
@@ -59,18 +59,11 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_vddio_sd0: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 29 0>;
-		};
+	reg_vddio_sd0: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 29 0>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx23-xfi3.dts b/arch/arm/boot/dts/nxp/mxs/imx23-xfi3.dts
index a6213c590f94..28341d8315c2 100644
--- a/arch/arm/boot/dts/imx23-xfi3.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-xfi3.dts
@@ -153,24 +153,24 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
+		pwms = <&pwm 2 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		voldown {
+		key-voldown {
 			label = "volume-down";
 			linux,code = <114>;
 			gpios = <&gpio2 7 0>;
 			debounce-interval = <20>;
 		};
 
-		volup {
+		key-volup {
 			label = "volume-up";
 			linux,code = <115>;
 			gpios = <&gpio2 8 0>;
diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/nxp/mxs/imx23.dtsi
index 8257630f7a49..0309592af1e1 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx23.dtsi
@@ -59,13 +59,11 @@
 				reg = <0x80000000 0x2000>;
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
 				reg = <0x80004000 0x2000>;
-				interrupts = <0 14 20 0
-					      13 13 13 13>;
-				interrupt-names = "empty", "ssp0", "ssp1", "empty",
-						  "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+				interrupts = <0>, <14>, <20>, <0>,
+					     <13>, <13>, <13>, <13>;
 				#dma-cells = <1>;
 				dma-channels = <8>;
 				clocks = <&clks 15>;
@@ -76,7 +74,7 @@
 				status = "disabled";
 			};
 
-			gpmi-nand@8000c000 {
+			nand-controller@8000c000 {
 				compatible = "fsl,imx23-gpmi-nand";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -112,7 +110,7 @@
 				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <0>;
 					interrupts = <16>;
 					gpio-controller;
@@ -122,7 +120,7 @@
 				};
 
 				gpio1: gpio@1 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <1>;
 					interrupts = <17>;
 					gpio-controller;
@@ -132,7 +130,7 @@
 				};
 
 				gpio2: gpio@2 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <2>;
 					interrupts = <18>;
 					gpio-controller;
@@ -267,6 +265,14 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				mmc0_sck_cfg: mmc0-sck-cfg@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX23_PAD_SSP1_SCK__SSP1_SCK
+					>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				mmc1_4bit_pins_a: mmc1-4bit@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -406,13 +412,13 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
 				reg = <0x80024000 0x2000>;
-				interrupts = <7 5 9 26
-					      19 0 25 23
-					      60 58 9 0
-					      0 0 0 0>;
+				interrupts = <7>, <5>, <9>, <26>,
+					     <19>, <0>, <25>, <23>,
+					     <60>, <58>, <9>, <0>,
+					     <0>, <0>, <0>, <0>;
 				interrupt-names = "audio-adc", "audio-dac", "spdif-tx", "i2c",
 						  "saif0", "empty", "auart0-rx", "auart0-tx",
 						  "auart1-rx", "auart1-tx", "saif1", "empty",
@@ -422,10 +428,10 @@
 				clocks = <&clks 16>;
 			};
 
-			dcp@80028000 {
+			dcp: crypto@80028000 {
 				compatible = "fsl,imx23-dcp";
 				reg = <0x80028000 0x2000>;
-				interrupts = <53 54>;
+				interrupts = <53>, <54>;
 				status = "okay";
 			};
 
@@ -434,7 +440,7 @@
 				status = "disabled";
 			};
 
-			ocotp@8002c000 {
+			efuse@8002c000 {
 				compatible = "fsl,imx23-ocotp", "fsl,ocotp";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -450,7 +456,7 @@
 			lcdif@80030000 {
 				compatible = "fsl,imx23-lcdif";
 				reg = <0x80030000 2000>;
-				interrupts = <46 45>;
+				interrupts = <46>, <45>;
 				clocks = <&clks 38>;
 				status = "disabled";
 			};
@@ -478,7 +484,7 @@
 			ranges;
 
 			clks: clkctrl@80040000 {
-				compatible = "fsl,imx23-clkctrl", "fsl,clkctrl";
+				compatible = "fsl,imx23-clkctrl";
 				reg = <0x80040000 0x2000>;
 				#clock-cells = <1>;
 			};
@@ -519,7 +525,8 @@
 			lradc: lradc@80050000 {
 				compatible = "fsl,imx23-lradc";
 				reg = <0x80050000 0x2000>;
-				interrupts = <36 37 38 39 40 41 42 43 44>;
+				interrupts = <36>, <37>, <38>, <39>, <40>,
+					     <41>, <42>, <43>, <44>;
 				status = "disabled";
 				clocks = <&clks 26>;
 				#io-channel-cells = <1>;
@@ -554,7 +561,7 @@
 				compatible = "fsl,imx23-pwm";
 				reg = <0x80064000 0x2000>;
 				clocks = <&clks 30>;
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				fsl,pwm-number = <5>;
 				status = "disabled";
 			};
@@ -562,7 +569,7 @@
 			timrot@80068000 {
 				compatible = "fsl,imx23-timrot", "fsl,timrot";
 				reg = <0x80068000 0x2000>;
-				interrupts = <28 29 30 31>;
+				interrupts = <28>, <29>, <30>, <31>;
 				clocks = <&clks 28>;
 			};
 
@@ -591,7 +598,7 @@
 				reg = <0x80070000 0x2000>;
 				interrupts = <0>;
 				clocks = <&clks 32>, <&clks 16>;
-				clock-names = "uart", "apb_pclk";
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-apf28.dts b/arch/arm/boot/dts/nxp/mxs/imx28-apf28.dts
new file mode 100644
index 000000000000..98672932e41b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-apf28.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "Armadeus Systems APF28 module";
+	compatible = "armadeus,imx28-apf28", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0 0x300000>;
+	};
+
+	partition@300000 {
+		label = "env";
+		reg = <0x300000 0x80000>;
+	};
+
+	partition@380000 {
+		label = "env2";
+		reg = <0x380000 0x80000>;
+	};
+
+	partition@400000 {
+		label = "dtb";
+		reg = <0x400000 0x80000>;
+	};
+
+	partition@480000 {
+		label = "splash";
+		reg = <0x480000 0x80000>;
+	};
+
+	partition@500000 {
+		label = "kernel";
+		reg = <0x500000 0x800000>;
+	};
+
+	partition@d00000 {
+		label = "rootfs";
+		reg = <0xd00000 0xf300000>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-apf28dev.dts b/arch/arm/boot/dts/nxp/mxs/imx28-apf28dev.dts
new file mode 100644
index 000000000000..6c87266eb135
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-apf28dev.dts
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ */
+
+/* APF28Dev is a docking board for the APF28 SOM */
+#include "imx28-apf28.dts"
+
+/ {
+	model = "Armadeus Systems APF28Dev docking/development board";
+	compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
+
+	reg_usb0_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 23 1>;
+		enable-active-high;
+	};
+
+	reg_can0_vcc: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "can0_vcc";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio0 21 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+
+		pwms = <&pwm 3 191000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-button {
+			label = "User button";
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+			linux,code = <0x100>;
+			wakeup-source;
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	xceiver-supply = <&reg_can0_vcc>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_16bit_pins_a
+		     &lcdif_pins_apf28dev>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <16>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33000033>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <96>;
+				hfront-porch = <96>;
+				vback-porch = <20>;
+				vfront-porch = <21>;
+				hsync-len = <64>;
+				vsync-len = <4>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_apf28dev>;
+
+	hog_pins_apf28dev: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D16__GPIO_1_16
+			MX28_PAD_LCD_D17__GPIO_1_17
+			MX28_PAD_LCD_D18__GPIO_1_18
+			MX28_PAD_LCD_D19__GPIO_1_19
+			MX28_PAD_LCD_D20__GPIO_1_20
+			MX28_PAD_LCD_D21__GPIO_1_21
+			MX28_PAD_LCD_D22__GPIO_1_22
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apf28dev: lcdif-apf28dev@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	usb0_otg_apf28dev: otg-apf28dev@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D23__GPIO_1_23
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_otg_apf28dev
+		     &usb0_id_pins_b>;
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-apx4devkit.dts b/arch/arm/boot/dts/nxp/mxs/imx28-apx4devkit.dts
new file mode 100644
index 000000000000..f9bf40d96568
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-apx4devkit.dts
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "Bluegiga APX4 Development Kit";
+	compatible = "bluegiga,apx4devkit", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x04000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_3p3v: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+
+	sound {
+		compatible = "bluegiga,apx4devkit-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "apx4devkit-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio3 28 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_2pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_apx4>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <88>;
+				hfront-porch = <40>;
+				vback-porch = <32>;
+				vfront-porch = <13>;
+				hsync-len = <48>;
+				vsync-len = <3>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "phg,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_RDY1__GPIO_0_21
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_JTAG_RTCK__GPIO_4_20
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apx4: lcdif-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA4__SSP2_D0
+			MX28_PAD_SSP0_DATA5__SSP2_D3
+			MX28_PAD_SSP0_DATA6__SSP2_CMD
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+			MX28_PAD_SSP2_SS1__SSP2_D1
+			MX28_PAD_SSP2_SS2__SSP2_D2
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_12mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb1 {
+      status = "okay";
+};
+
+&usbphy1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10036.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10036.dts
new file mode 100644
index 000000000000..d004b1cbb4ae
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10036.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Free Electrons
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Crystalfontz CFA-10036 Board";
+	compatible = "crystalfontz,cfa10036", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_cfa10036>;
+
+		power {
+			gpios = <&gpio3 4 1>;
+			default-state = "on";
+		};
+	};
+
+	reg_vddio_sd0: vddio-sd0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mmc_pwr_cfa10036>;
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_b>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ssd1306: oled@3c {
+		compatible = "solomon,ssd1306fb-i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ssd1306_cfa10036>;
+		reg = <0x3c>;
+		reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+		solomon,height = <32>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,com-lrremap;
+		solomon,com-invdir;
+		solomon,com-offset = <32>;
+	};
+};
+
+&pinctrl {
+	ssd1306_cfa10036: ssd1306-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins_cfa10036: leds-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_RX__GPIO_3_4
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	usb0_otg_cfa10036: otg-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY0__USB0_ID
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			0x31c3 /*
+			MX28_PAD_PWM3__GPIO_3_28 */
+		>;
+		fsl,drive-strength = <0>;
+		fsl,voltage = <1>;
+		fsl,pull-up = <0>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_otg_cfa10036>;
+	dr_mode = "peripheral";
+	phy_type = "utmi";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10037.dts
index d3e9a731525b..c72fe2d392f1 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10037.dts
@@ -64,20 +64,13 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10037>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10037>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10049.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10049.dts
new file mode 100644
index 000000000000..f0ce897b9d5c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10049.dts
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Free Electrons
+ */
+
+/*
+ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+#include "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10049 Board";
+	compatible = "crystalfontz,cfa10049", "crystalfontz,cfa10036", "fsl,imx28";
+
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2cmux_pins_cfa10049>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adc0: nau7802@2a {
+				compatible = "nuvoton,nau7802";
+				reg = <0x2a>;
+				nuvoton,vldo = <3000>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			adc1: nau7802@2a {
+				compatible = "nuvoton,nau7802";
+				reg = <0x2a>;
+				nuvoton,vldo = <3000>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+				adc2: nau7802@2a {
+				compatible = "nuvoton,nau7802";
+				reg = <0x2a>;
+				nuvoton,vldo = <3000>;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pca_pins_cfa10049>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <19 0x2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
+
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10049>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
+	};
+
+	spi-2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10049>;
+		status = "okay";
+		sck-gpios = <&gpio2 16 0>;
+		mosi-gpios = <&gpio2 17 0>;
+		miso-gpios = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8357: hx8357@0 {
+			compatible = "himax,hx8357b", "himax,hx8357";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+			im-gpios = <&gpio5 4 0 &gpio5 5 0 &gpio5 6 0>;
+		};
+	};
+
+	spi-3 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi3_pins_cfa10049>;
+		status = "okay";
+		sck-gpios = <&gpio0 24 0>;
+		mosi-gpios = <&gpio0 28 0>;
+		cs-gpios = <&gpio0 17 0 &gpio0 26 0 &gpio0 27 0>;
+		num-chipselects = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio5: gpio5@0 {
+			compatible = "fairchild,74hc595";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+			registers-number = <2>;
+			spi-max-frequency = <100000>;
+		};
+
+		gpio6: gpio6@1 {
+			compatible = "fairchild,74hc595";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <1>;
+			registers-number = <4>;
+			spi-max-frequency = <100000>;
+		};
+
+		dac0: dh2228@2 {
+			compatible = "rohm,dh2228fv";
+			reg = <2>;
+			spi-max-frequency = <100000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
+
+		rotary-button {
+			label = "rotary_button";
+			gpios = <&gpio3 26 1>;
+			debounce-interval = <10>;
+			linux,code = <28>;
+		};
+	};
+
+	rotary {
+		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_pins_cfa10049>;
+		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
+		linux,axis = <1>; /* REL_Y */
+		rotary-encoder,relative-axis;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&w1_gpio_pins>;
+		status = "okay";
+		gpios = <&gpio1 21 0>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10049
+		     &lcdif_pins_cfa10049
+		     &lcdif_pins_cfa10049_pullup>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9216000>;
+				hactive = <320>;
+				vactive = <480>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <15>;
+				vsync-len = <15>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a
+		&mac0_pins_cfa10049>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10049: usb-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	i2cmux_pins_cfa10049: i2cmux-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D22__GPIO_1_22
+			MX28_PAD_LCD_D23__GPIO_1_23
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_pins_cfa10049: mac0-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	pca_pins_cfa10049: pca-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS0__GPIO_2_19
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	rotary_pins_cfa10049: rotary-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_I2C0_SCL__GPIO_3_24
+			MX28_PAD_I2C0_SDA__GPIO_3_25
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SAIF1_SDATA0__GPIO_3_26
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	spi2_pins_cfa10049: spi2-cfa10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	spi3_pins_cfa10049: spi3-cfa10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_GPMI_RESETN__GPIO_0_28
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_ALE__GPIO_0_26
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10049: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	w1_gpio_pins: w1-gpio@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D21__GPIO_1_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dts
new file mode 100644
index 000000000000..cb68edd6101b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dts
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * 				  Free Electrons
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+#include "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10055 Board";
+	compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	spi-2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10055>;
+		status = "okay";
+		sck-gpios = <&gpio2 16 0>;
+		mosi-gpios = <&gpio2 17 0>;
+		miso-gpios = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8357: hx8357@0 {
+			compatible = "himax,hx8357b", "himax,hx8357";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10055
+		     &lcdif_pins_cfa10055
+		     &lcdif_pins_cfa10055_pullup>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9216000>;
+				hactive = <320>;
+				vactive = <480>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <15>;
+				vsync-len = <15>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&pinctrl {
+	spi2_pins_cfa10055: spi2-cfa10055@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10055: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10056.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10056.dts
new file mode 100644
index 000000000000..bc2d6fcad12f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10056.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Free Electrons
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+#include "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10056 Board";
+	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	spi-2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10056>;
+		status = "okay";
+		sck-gpios = <&gpio2 16 0>;
+		mosi-gpios = <&gpio2 17 0>;
+		miso-gpios = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8369: hx8369@0 {
+			compatible = "himax,hx8369a", "himax,hx8369";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+};
+
+&pinctrl {
+	spi2_pins_cfa10056: spi2-cfa10056@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_pins_cfa10056: lcdif-10056@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+			&lcdif_pins_cfa10056
+			&lcdif_pins_cfa10056_pullup >;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <32000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <5>;
+				vsync-len = <5>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10057.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10057.dts
new file mode 100644
index 000000000000..5875c3d7ba97
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10057.dts
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2012 Free Electrons
+ */
+
+/*
+ * The CFA-10057 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+#include "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10057 Board";
+	compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
+
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10057>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10057
+		     &lcdif_pins_cfa10057>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hfront-porch = <12>;
+				hback-porch = <2>;
+				vfront-porch = <5>;
+				vback-porch = <3>;
+				hsync-len = <2>;
+				vsync-len = <2>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10057: usb-10057@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10057: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10058.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10058.dts
new file mode 100644
index 000000000000..b414e67ef379
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10058.dts
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2013 Free Electrons
+ */
+
+/*
+ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+#include "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10058 Board";
+	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
+
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10058>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+			 &lcdif_pins_cfa10058>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <40>;
+				hfront-porch = <40>;
+				vback-porch = <13>;
+				vfront-porch = <29>;
+				hsync-len = <8>;
+				vsync-len = <8>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10058: usb-10058@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10058: lcdif-10058@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-485.dts
new file mode 100644
index 000000000000..b73020ff1053
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-485.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include "imx28-duckbill-2.dts"
+
+/ {
+	model = "I2SE Duckbill 2 485";
+	compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
+
+	leds {
+		rs485-red {
+			label = "duckbill:red:rs485";
+			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+		};
+
+		rs485-green {
+			label = "duckbill:green:rs485";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-enocean.dts
new file mode 100644
index 000000000000..473d99b9b42f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-enocean.dts
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "imx28-duckbill-2.dts"
+
+/ {
+	model = "I2SE Duckbill 2 EnOcean";
+	compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
+
+	leds {
+		enocean-blue {
+			label = "duckbill:blue:enocean";
+			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+		};
+
+		enocean-red {
+			label = "duckbill:red:enocean";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		};
+
+		enocean-green {
+			label = "duckbill:green:enocean";
+			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&enocean_button>;
+
+		key-enocean {
+			label = "EnOcean";
+			linux,code = <KEY_NEW>;
+			gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_AUART0_CTS__GPIO_3_2
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
+
+&pinctrl {
+	enocean_button: enocean-button@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-spi.dts
new file mode 100644
index 000000000000..859d97a5a775
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-spi.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include "imx28-duckbill-2.dts"
+
+/ {
+	model = "I2SE Duckbill 2 SPI";
+	compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
+
+	aliases {
+		ethernet1 = &qca7000;
+	};
+};
+
+&auart0 {
+	status = "disabled";
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&pinctrl {
+	qca7000_pins: qca7000@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
+			MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
+			MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
+			MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
+			MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
+			MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	/delete-property/ bus-width;
+	/delete-property/ vmmc-supply;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		reg = <0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&qca7000_pins>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <8000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2.dts
new file mode 100644
index 000000000000..4e28212e9626
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+	model = "I2SE Duckbill 2";
+	compatible = "i2se,duckbill-2", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		status-red {
+			label = "duckbill:red:status";
+			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		status-green {
+			label = "duckbill:green:status";
+			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+	phy-supply = <&reg_3p3v>;
+	phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_phy_int_pin>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			max-speed = <100>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_reset_pin: mac0-phy-reset@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_int_pin: mac0-phy-int@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SAIF0_MCLK__GPIO_3_20
+			MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+	non-removable;
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_b
+		&mmc2_cd_cfg &mmc2_sck_cfg_b>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill.dts
new file mode 100644
index 000000000000..13ffd533fdea
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+	model = "I2SE Duckbill";
+	compatible = "i2se,duckbill", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		status-red {
+			label = "duckbill:red:status";
+			gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		status-green {
+			label = "duckbill:green:status";
+			gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+	phy-supply = <&reg_3p3v>;
+	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_reset_pin: mac0-phy-reset@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_RX__GPIO_3_4
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx283lc.dts
index 29f8a3a245d4..7ae2d4ca8ef0 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx283lc.dts
@@ -47,7 +47,7 @@
 	status = "okay";
 };
 
-&pinctrl{
+&pinctrl {
 	pinctrl-names = "default";
 	pinctrl-0 = <&hog_pins_cpuimx283>;
 
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx287lc.dts
index cd875ace168d..cd875ace168d 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx287lc.dts
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx28lc.dtsi
index 3280fddaaf0d..652fc9e57a55 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx28lc.dtsi
@@ -14,17 +14,17 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 4 1000000>;
+		pwms = <&pwm 4 1000000 0>;
 		brightness-levels = <0 25 50 75 100 125 150 175 200 225 255>;
 		default-brightness-level = <10>;
 	};
 
-	button-sw3 {
+	gpio-keys-0 {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_button_sw3_pins_mbmx28lc>;
 
-		sw3 {
+		switch-sw3 {
 			label = "SW3";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -32,12 +32,12 @@
 		};
 	};
 
-	button-sw4 {
+	gpio-keys-1 {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_button_sw4_pins_mbmx28lc>;
 
-		sw4 {
+		switch-sw4 {
 			label = "SW4";
 			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -69,55 +69,45 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_lcd_3v3: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&reg_lcd_3v3_pins_mbmx28lc>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_lcd_3v3: regulator-1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&reg_lcd_3v3_pins_mbmx28lc>;
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb0_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&reg_usb0_vbus_pins_mbmx28lc>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb0_vbus: regulator-2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&reg_usb0_vbus_pins_mbmx28lc>;
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&reg_usb1_vbus_pins_mbmx28lc>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb1_vbus: regulator-3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&reg_usb1_vbus_pins_mbmx28lc>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-evk.dts b/arch/arm/boot/dts/nxp/mxs/imx28-evk.dts
new file mode 100644
index 000000000000..9ebb7371e235
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-evk.dts
@@ -0,0 +1,352 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2012 Freescale Semiconductor, Inc.
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "Freescale i.MX28 Evaluation Kit";
+	compatible = "fsl,imx28-evk", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+
+	reg_fec_3v3: regulator-fec-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 15 0>;
+	};
+
+	reg_usb0_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 9 0>;
+		enable-active-high;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 8 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 30 0>;
+		enable-active-high;
+	};
+
+	reg_can_3v3: regulator-can-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 13 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx28-evk-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "imx28-evk-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio3_5>;
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio3 5 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	backlight_display: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 2 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_pins_a>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	xceiver-supply = <&reg_can_3v3>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	xceiver-supply = <&reg_can_3v3>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+		     &gpmi_pins_evk>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_evk>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	fsl,ave-ctrl = <4>;
+	fsl,ave-delay = <2>;
+	fsl,settling = <10>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	at24@51 {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x51>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-supply = <&reg_fec_3v3>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP1_CMD__GPIO_2_13
+			MX28_PAD_SSP1_DATA3__GPIO_2_15
+			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+			MX28_PAD_SSP1_SCK__GPIO_2_12
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_AUART2_RX__GPIO_3_8
+			MX28_PAD_AUART2_TX__GPIO_3_9
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pin_gpio3_5: led_gpio3_5@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	gpmi_pins_evk: gpmi-nand-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPMI_CE1N
+			MX28_PAD_GPMI_RDY1__GPMI_READY1
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_evk: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <8>;
+	wp-gpios = <&gpio2 12 0>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp1 {
+	compatible = "fsl,imx28-mmc";
+	bus-width = <8>;
+	wp-gpios = <&gpio0 28 0>;
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_pins_a>;
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-lwe.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-lwe.dtsi
new file mode 100644
index 000000000000..69fcb0dde940
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-lwe.dtsi
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	aliases {
+		spi2 = &ssp3;
+	};
+
+	chosen {
+		bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1";
+	};
+
+	memory@40000000 {
+		reg = <0x40000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	reg_3v3: regulator-reg-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_5v: regulator-reg-usb-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_fec_3v3: regulator-reg-fec-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-phy";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	#sound-dai-cells = <0>;
+	assigned-clocks = <&clks 53>;
+	assigned-clock-rates = <12000000>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&spi3_pins_a {
+	fsl,pinmux-ids = <
+		MX28_PAD_AUART2_RX__SSP3_D4
+		MX28_PAD_AUART2_TX__SSP3_D5
+		MX28_PAD_SSP3_SCK__SSP3_SCK
+		MX28_PAD_SSP3_MOSI__SSP3_CMD
+		MX28_PAD_SSP3_MISO__SSP3_D0
+		MX28_PAD_SSP3_SS0__SSP3_D3
+		MX28_PAD_AUART2_TX__GPIO_3_9
+	>;
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a>;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	non-removable;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&ssp3 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi3_pins_a>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0 0x80000>;
+				read-only;
+			};
+
+			partition@80000 {
+				label = "env0";
+				reg = <0x80000 0x10000>;
+			};
+
+			partition@90000 {
+				label = "env1";
+				reg = <0x90000 0x10000>;
+			};
+
+			partition@100000 {
+				label = "kernel";
+				reg = <0x100000 0x400000>;
+			};
+
+			partition@500000 {
+				label = "swupdate";
+				reg = <0x500000 0x800000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb_5v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb_5v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_b>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-m28.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-m28.dtsi
new file mode 100644
index 000000000000..66facef10ba9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-m28.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx28.dtsi"
+
+/ {
+	model = "Aries/DENX M28";
+	compatible = "aries,m28", "denx,m28", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3p3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&gpmi {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	rtc: rtc@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-m28cu3.dts b/arch/arm/boot/dts/nxp/mxs/imx28-m28cu3.dts
new file mode 100644
index 000000000000..34b4d3246db1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-m28cu3.dts
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "MSR M28CU3";
+	compatible = "msr,m28cu3", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_gpio>;
+
+		user1 {
+			label = "sd0-led";
+			gpios = <&gpio2 26 0>;
+			linux,default-trigger = "mmc0";
+		};
+
+		user2 {
+			label = "sd1-led";
+			gpios = <&gpio2 24 0>;
+			linux,default-trigger = "mmc2";
+		};
+	};
+
+	reg_3p3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vddio_sd0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 29 0>;
+	};
+
+	reg_vddio_sd1: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 0>;
+	};
+
+	reg_usb1_vbus: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 8 0>;
+		enable-active-high;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_2pins_b>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&gpmi {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+
+	partition@0 {
+		label = "gpmi-nfc-0-boot";
+		reg = <0x00000000 0x01400000>;
+		read-only;
+	};
+
+	partition@1 {
+		label = "gpmi-nfc-general-use";
+		reg = <0x01400000 0x0ec00000>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_m28>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <6410256>;
+				hactive = <320>;
+				vactive = <240>;
+				hback-porch = <38>;
+				hfront-porch = <20>;
+				vback-porch = <15>;
+				vfront-porch = <5>;
+				hsync-len = <30>;
+				vsync-len = <3>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&ocotp {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS0__GPIO_2_19
+			MX28_PAD_PWM4__GPIO_3_29
+			MX28_PAD_AUART2_RX__GPIO_3_8
+			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_m28: lcdif-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_VSYNC__LCD_VSYNC
+			MX28_PAD_LCD_HSYNC__LCD_HSYNC
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_RESET__LCD_RESET
+			MX28_PAD_LCD_CS__LCD_ENABLE
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins_gpio: leds-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP3_MISO__GPIO_2_26
+			MX28_PAD_SSP3_SCK__GPIO_2_24
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_cd_cfg
+		     &mmc0_sck_cfg>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_a
+		     &mmc2_cd_cfg
+		     &mmc2_sck_cfg_a>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd1>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-m28evk.dts b/arch/arm/boot/dts/nxp/mxs/imx28-m28evk.dts
new file mode 100644
index 000000000000..13070ca08cff
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-m28evk.dts
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+
+ * Copyright (C) 2012 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx28-m28.dtsi"
+
+/ {
+	model = "Aries/DENX M28EVK";
+	compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	reg_vddio_sd0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+
+	reg_usb0_vbus: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 12 0>;
+	};
+
+	reg_usb1_vbus: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 13 0>;
+	};
+
+	sound {
+		compatible = "denx,m28evk-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "m28evk-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_b>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	eeprom: eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_m28>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33260000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <0>;
+				hfront-porch = <256>;
+				vback-porch = <0>;
+				vfront-porch = <45>;
+				hsync-len = <1>;
+				vsync-len = <1>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	status = "okay";
+	fsl,lradc-touchscreen-wires = <4>;
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	clocks = <&clks 57>, <&clks 57>;
+	clock-names = "ipg", "ahb";
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_AUART2_CTS__GPIO_3_10
+			MX28_PAD_AUART2_RTS__GPIO_3_11
+			MX28_PAD_AUART3_RX__GPIO_3_12
+			MX28_PAD_AUART3_TX__GPIO_3_13
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_m28: lcdif-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_ENABLE__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		     &mmc0_cd_cfg
+		     &mmc0_sck_cfg>;
+	bus-width = <8>;
+	wp-gpios = <&gpio3 10 0>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb0_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_a>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-pinfunc.h b/arch/arm/boot/dts/nxp/mxs/imx28-pinfunc.h
index e11f69ba0fe4..d427e6c2fa78 100644
--- a/arch/arm/boot/dts/imx28-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX28 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MX28_PINCTRL_H__
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-sps1.dts b/arch/arm/boot/dts/nxp/mxs/imx28-sps1.dts
new file mode 100644
index 000000000000..0f01dded4e3d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-sps1.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2012 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "SchulerControl GmbH, SC SPS 1";
+	compatible = "schulercontrol,imx28-sps1", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_usb0_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 9 0>;
+	};
+
+	leds {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led@1 {
+			label = "sps1-1:yellow:user";
+			gpios = <&gpio0 6 0>;
+			linux,default-trigger = "heartbeat";
+			reg = <0>;
+		};
+
+		led@2 {
+			label = "sps1-2:red:user";
+			gpios = <&gpio0 3 0>;
+			linux,default-trigger = "heartbeat";
+			reg = <1>;
+		};
+
+		led@3 {
+			label = "sps1-3:red:user";
+			gpios = <&gpio0 0 0>;
+			default-trigger = "heartbeat";
+			reg = <2>;
+		};
+
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog-gpios@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D06__GPIO_0_6
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "everspin,mr25h256", "mr25h256";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb0_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_b>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-ts4600.dts b/arch/arm/boot/dts/nxp/mxs/imx28-ts4600.dts
new file mode 100644
index 000000000000..ae6ed5c41be3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-ts4600.dts
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Savoir-Faire Linux
+ * Author: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+#include "dt-bindings/gpio/gpio.h"
+
+/ {
+
+	model = "Technologic Systems i.MX28 TS-4600";
+	compatible = "technologic,imx28-ts4600", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x10000000>;   /* 256MB */
+	};
+
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpio = <&gpio3 28 GPIO_ACTIVE_LOW>;
+	};
+
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	en_sd_pwr: en-sd-pwr@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_PWM3__GPIO_3_28
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_sck_cfg
+		     &en_sd_pwr>;
+	broken-cd;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/nxp/mxs/imx28-tx28.dts
index 164254c28f8e..5485fe118dc4 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-tx28.dts
@@ -1,43 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 /*
  * Copyright 2012 Shawn Guo <shawn.guo@linaro.org>
  * Copyright 2013-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -167,7 +131,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 0 500000>;
+		pwms = <&pwm 0 500000 0>;
 		/*
 		 * a silly way to create a 1:1 relationship between the
 		 * PWM value and the actual duty cycle
@@ -221,16 +185,16 @@
 		linux,no-autorepeat;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tx28_spi_gpio_pins>;
 
-		gpio-sck = <&gpio2 24 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio2 25 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <3>;
 		cs-gpios = <
 			&gpio2 27 GPIO_ACTIVE_LOW
@@ -239,24 +203,6 @@
 		>;
 		/* enable this and disable ssp3 below, if you need full duplex SPI transfer */
 		status = "disabled";
-
-		spi@0 {
-			compatible = "spidev";
-			reg = <0>;
-			spi-max-frequency = <57600000>;
-		};
-
-		spi@1 {
-			compatible = "spidev";
-			reg = <1>;
-			spi-max-frequency = <57600000>;
-		};
-
-		spi@2 {
-			compatible = "spidev";
-			reg = <2>;
-			spi-max-frequency = <57600000>;
-		};
 	};
 };
 
@@ -314,6 +260,7 @@
 	sgtl5000: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 		clocks = <&mclk>;
@@ -356,7 +303,7 @@
 	};
 
 	ds1339: rtc@68 {
-		compatible = "mxim,ds1339";
+		compatible = "dallas,ds1339";
 		reg = <0x68>;
 		trickle-resistor-ohms = <250>;
 		trickle-diode-disable;
@@ -700,30 +647,13 @@
 	pinctrl-0 = <&spi3_pins_a>;
 	clock-frequency = <57600000>;
 	status = "okay";
-
-	spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <57600000>;
-	};
-
-	spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <57600000>;
-	};
-
-	spi@2 {
-		compatible = "spidev";
-		reg = <2>;
-		spi-max-frequency = <57600000>;
-	};
 };
 
 &usb0 {
 	vbus-supply = <&reg_usb0_vbus>;
 	disable-over-current;
 	dr_mode = "peripheral";
+	phy_type = "utmi";
 	status = "okay";
 };
 
@@ -731,19 +661,18 @@
 	vbus-supply = <&reg_usb1_vbus>;
 	disable-over-current;
 	dr_mode = "host";
+	phy_type = "utmi";
 	status = "okay";
 };
 
 &usbphy0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&tx28_usbphy0_pins>;
-	phy_type = "utmi";
 	status = "okay";
 };
 
 &usbphy1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&tx28_usbphy1_pins>;
-	phy_type = "utmi";
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
new file mode 100644
index 000000000000..6c5e6856648a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28-lwe.dtsi"
+
+/ {
+	model = "Liebherr XEA board";
+	compatible = "lwn,imx28-xea", "fsl,imx28";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_GPMI_D02__GPIO_0_2
+			MX28_PAD_GPMI_D05__GPIO_0_5
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_RDY0__GPIO_0_20
+			MX28_PAD_GPMI_RDY1__GPIO_0_21
+			MX28_PAD_GPMI_RDY2__GPIO_0_22
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+			MX28_PAD_LCD_VSYNC__GPIO_1_28
+			MX28_PAD_SSP1_SCK__GPIO_2_12
+			MX28_PAD_SSP1_CMD__GPIO_2_13
+			MX28_PAD_SSP2_SS1__GPIO_2_20
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+			MX28_PAD_LCD_D00__GPIO_1_0
+			MX28_PAD_LCD_D01__GPIO_1_1
+			MX28_PAD_LCD_D02__GPIO_1_2
+			MX28_PAD_LCD_D03__GPIO_1_3
+			MX28_PAD_LCD_D04__GPIO_1_4
+			MX28_PAD_LCD_D05__GPIO_1_5
+			MX28_PAD_LCD_D06__GPIO_1_6
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	hog_pins_tiva: hog@1 {
+		reg = <1>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY3__GPIO_0_23
+			MX28_PAD_GPMI_WRN__GPIO_0_25
+		>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	hog_pins_coding: hog@2 {
+		reg = <2>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D01__GPIO_0_1
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D04__GPIO_0_4
+			MX28_PAD_GPMI_D06__GPIO_0_6
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&reg_fec_3v3 {
+	gpio = <&gpio0 0 0>;
+};
+
+&reg_usb_5v {
+	gpio = <&gpio0 2 0>;
+};
+
+&spi2_pins_a {
+	fsl,pinmux-ids = <
+		MX28_PAD_SSP2_SCK__SSP2_SCK
+		MX28_PAD_SSP2_MOSI__SSP2_CMD
+		MX28_PAD_SSP2_MISO__SSP2_D0
+		MX28_PAD_SSP2_SS0__GPIO_2_19
+	>;
+};
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
index e14d8ef0158b..4817fba2d938 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
@@ -78,17 +78,13 @@
 				status = "disabled";
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
 				reg = <0x80004000 0x2000>;
-				interrupts = <82 83 84 85
-					      88 88 88 88
-					      88 88 88 88
-					      87 86 0 0>;
-				interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
-						  "gpmi0", "gmpi1", "gpmi2", "gmpi3",
-						  "gpmi4", "gmpi5", "gpmi6", "gmpi7",
-						  "hsadc", "lcdif", "empty", "empty";
+				interrupts = <82>, <83>, <84>, <85>,
+					     <88>, <88>, <88>, <88>,
+					     <88>, <88>, <88>, <88>,
+					     <87>, <86>, <0>, <0>;
 				#dma-cells = <1>;
 				dma-channels = <16>;
 				clocks = <&clks 25>;
@@ -100,7 +96,7 @@
 				status = "disabled";
 			};
 
-			gpmi: gpmi-nand@8000c000 {
+			gpmi: nand-controller@8000c000 {
 				compatible = "fsl,imx28-gpmi-nand";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -110,6 +106,8 @@
 				interrupt-names = "bch";
 				clocks = <&clks 50>;
 				clock-names = "gpmi_io";
+				assigned-clocks = <&clks 13>;
+				assigned-clock-parents = <&clks 10>;
 				dmas = <&dma_apbh 4>;
 				dma-names = "rx-tx";
 				status = "disabled";
@@ -166,7 +164,7 @@
 				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <0>;
 					interrupts = <127>;
 					gpio-controller;
@@ -176,7 +174,7 @@
 				};
 
 				gpio1: gpio@1 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <1>;
 					interrupts = <126>;
 					gpio-controller;
@@ -186,7 +184,7 @@
 				};
 
 				gpio2: gpio@2 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <2>;
 					interrupts = <125>;
 					gpio-controller;
@@ -196,7 +194,7 @@
 				};
 
 				gpio3: gpio@3 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <3>;
 					interrupts = <124>;
 					gpio-controller;
@@ -206,7 +204,7 @@
 				};
 
 				gpio4: gpio@4 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <4>;
 					interrupts = <123>;
 					gpio-controller;
@@ -948,6 +946,16 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				usb1_pins_b: usb1@1 {
+					reg = <1>;
+					fsl,pinmux-ids = <
+						MX28_PAD_PWM2__USB1_OVERCURRENT
+					>;
+					fsl,drive-strength = <MXS_DRIVE_12mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				usb0_id_pins_a: usb0id@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -982,26 +990,22 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
 				reg = <0x80024000 0x2000>;
-				interrupts = <78 79 66 0
-					      80 81 68 69
-					      70 71 72 73
-					      74 75 76 77>;
-				interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
-						  "saif0", "saif1", "i2c0", "i2c1",
-						  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
-						  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+				interrupts = <78>, <79>, <66>, <0>,
+					     <80>, <81>, <68>, <69>,
+					     <70>, <71>, <72>, <73>,
+					     <74>, <75>, <76>, <77>;
 				#dma-cells = <1>;
 				dma-channels = <16>;
 				clocks = <&clks 26>;
 			};
 
-			dcp: dcp@80028000 {
-				compatible = "fsl,imx28-dcp", "fsl,imx23-dcp";
+			dcp: crypto@80028000 {
+				compatible = "fsl,imx28-dcp";
 				reg = <0x80028000 0x2000>;
-				interrupts = <52 53 54>;
+				interrupts = <52>, <53>, <54>;
 				status = "okay";
 			};
 
@@ -1011,7 +1015,7 @@
 				status = "disabled";
 			};
 
-			ocotp: ocotp@8002c000 {
+			ocotp: efuse@8002c000 {
 				compatible = "fsl,imx28-ocotp", "fsl,ocotp";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -1096,7 +1100,7 @@
 			ranges;
 
 			clks: clkctrl@80040000 {
-				compatible = "fsl,imx28-clkctrl", "fsl,clkctrl";
+				compatible = "fsl,imx28-clkctrl";
 				reg = <0x80040000 0x2000>;
 				#clock-cells = <1>;
 			};
@@ -1132,8 +1136,8 @@
 			lradc: lradc@80050000 {
 				compatible = "fsl,imx28-lradc";
 				reg = <0x80050000 0x2000>;
-				interrupts = <10 14 15 16 17 18 19
-						20 21 22 23 24 25>;
+				interrupts = <10>, <14>, <15>, <16>, <17>, <18>, <19>,
+					     <20>, <21>, <22>, <23>, <24>, <25>;
 				status = "disabled";
 				clocks = <&clks 41>;
 				#io-channel-cells = <1>;
@@ -1181,7 +1185,7 @@
 				compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
 				reg = <0x80064000 0x2000>;
 				clocks = <&clks 44>;
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				fsl,pwm-number = <8>;
 				status = "disabled";
 			};
@@ -1189,7 +1193,7 @@
 			timer: timrot@80068000 {
 				compatible = "fsl,imx28-timrot", "fsl,timrot";
 				reg = <0x80068000 0x2000>;
-				interrupts = <48 49 50 51>;
+				interrupts = <48>, <49>, <50>, <51>;
 				clocks = <&clks 26>;
 			};
 
@@ -1248,7 +1252,7 @@
 				reg = <0x80074000 0x1000>;
 				interrupts = <47>;
 				clocks = <&clks 45>, <&clks 26>;
-				clock-names = "uart", "apb_pclk";
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
@@ -1317,7 +1321,7 @@
 			status = "disabled";
 		};
 
-		etn_switch: switch@800f8000 {
+		eth_switch: switch@800f8000 {
 			reg = <0x800f8000 0x8000>;
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/mxs-pinfunc.h b/arch/arm/boot/dts/nxp/mxs/mxs-pinfunc.h
index c6da987b20cb..31297abcbc71 100644
--- a/arch/arm/boot/dts/mxs-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/mxs/mxs-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX28 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MXS_PINCTRL_H__
diff --git a/arch/arm/boot/dts/nxp/vf/Makefile b/arch/arm/boot/dts/nxp/vf/Makefile
new file mode 100644
index 000000000000..0a4a7f9dd43e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/Makefile
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_VF610) += \
+	vf500-colibri-eval-v3.dtb \
+	vf610-bk4.dtb \
+	vf610-colibri-eval-v3.dtb \
+	vf610m4-colibri.dtb \
+	vf610-cosmic.dtb \
+	vf610m4-cosmic.dtb \
+	vf610-twr.dtb \
+	vf610-zii-cfu1.dtb \
+	vf610-zii-dev-rev-b.dtb \
+	vf610-zii-dev-rev-c.dtb \
+	vf610-zii-scu4-aib.dtb \
+	vf610-zii-spb4.dtb \
+	vf610-zii-ssmb-dtu.dtb \
+	vf610-zii-ssmb-spu3.dtb
diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri-eval-v3.dtsi
index e2da122a63f4..5a19da9313ae 100644
--- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri-eval-v3.dtsi
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2014 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
+ * Copyright 2014-2020 Toradex
  */
 
 / {
@@ -91,7 +55,7 @@
 	brightness-levels = <0 4 8 16 32 64 128 255>;
 	default-brightness-level = <6>;
 	power-supply = <&reg_3v3>;
-	status  = "okay";
+	status = "okay";
 };
 
 &dcu0 {
@@ -139,7 +103,7 @@
 	status = "okay";
 
 	/* M41T0M6 real time clock on carrier board */
-	rtc: m41t0m6@68 {
+	rtc: rtc@68 {
 		compatible = "st,m41t0";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
index fba37b8756f7..cc1e069c44e6 100644
--- a/arch/arm/boot/dts/vf-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
@@ -1,42 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2014 Toradex AG
+ * Copyright 2014-2020 Toradex
  *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 / {
diff --git a/arch/arm/boot/dts/nxp/vf/vf500-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/vf/vf500-colibri-eval-v3.dts
new file mode 100644
index 000000000000..088964f8dc4b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf500-colibri-eval-v3.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2014-2020 Toradex
+ */
+
+/dts-v1/;
+#include "vf500-colibri.dtsi"
+#include "vf-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri VF50 on Colibri Evaluation Board";
+	compatible = "toradex,vf500-colibri_vf50-on-eval", "toradex,vf500-colibri_vf50", "fsl,vf500";
+};
+
+&touchscreen {
+	vf50-ts-min-pressure = <200>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/vf/vf500-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf500-colibri.dtsi
new file mode 100644
index 000000000000..8af7ed56e653
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf500-colibri.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2014-2020 Toradex
+ */
+
+#include "vf500.dtsi"
+#include "vf-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri VF50 COM";
+	compatible = "toradex,vf500-colibri_vf50", "fsl,vf500";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x8000000>;
+	};
+
+	touchscreen: vf50-touchscreen {
+		compatible = "toradex,vf50-touchscreen";
+		io-channels = <&adc1 0>,<&adc0 0>,
+				<&adc0 1>,<&adc1 2>;
+		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "idle","default","gpios";
+		pinctrl-0 = <&pinctrl_touchctrl_idle>;
+		pinctrl-1 = <&pinctrl_touchctrl_default>;
+		pinctrl-2 = <&pinctrl_touchctrl_gpios>;
+		vf50-ts-min-pressure = <200>;
+		status = "disabled";
+	};
+};
+
+&nfc {
+	assigned-clocks = <&clks VF610_CLK_NFC>;
+	assigned-clock-rates = <33000000>;
+};
+
+&iomuxc {
+	vf610-colibri {
+		pinctrl_touchctrl_idle: touchctrl_idle {
+			fsl,pins = <
+				VF610_PAD_PTA18__GPIO_8		0x006d
+				VF610_PAD_PTA19__GPIO_9		0x006c
+				>;
+		};
+
+		pinctrl_touchctrl_default: touchctrl_default {
+			fsl,pins = <
+				VF610_PAD_PTA18__ADC0_SE0	0x0040
+				VF610_PAD_PTA19__ADC0_SE1	0x0040
+				VF610_PAD_PTA16__ADC1_SE0	0x0040
+				VF610_PAD_PTB2__ADC1_SE2	0x0040
+				>;
+		};
+
+		pinctrl_touchctrl_gpios: touchctrl_gpios {
+			fsl,pins = <
+				VF610_PAD_PTA23__GPIO_13	0x22e9
+				VF610_PAD_PTB23__GPIO_93	0x22e9
+				VF610_PAD_PTA22__GPIO_12	0x22e9
+				VF610_PAD_PTA11__GPIO_4		0x22e9
+				>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/vf500.dtsi b/arch/arm/boot/dts/nxp/vf/vf500.dtsi
index b0ec475017ad..0c0dd442300a 100644
--- a/arch/arm/boot/dts/vf500.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf500.dtsi
@@ -23,7 +23,7 @@
 	};
 
 	soc {
-		aips-bus@40000000 {
+		bus@40000000 {
 
 			intc: interrupt-controller@40003000 {
 				compatible = "arm,cortex-a9-gic";
@@ -43,7 +43,7 @@
 			};
 		};
 
-		aips-bus@40080000 {
+		bus@40080000 {
 			pmu@40089000 {
 				compatible = "arm,cortex-a5-pmu";
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/vf610-bk4.dts b/arch/arm/boot/dts/nxp/vf/vf610-bk4.dts
index 830c85476b3d..722182f5fd17 100644
--- a/arch/arm/boot/dts/vf610-bk4.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-bk4.dts
@@ -38,7 +38,7 @@
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
 		/* LED D5 */
-		led0: heartbeat {
+		led0: led-heartbeat {
 			label = "heartbeat";
 			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -61,14 +61,14 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	spi-gpio {
+	spi {
 		compatible = "spi-gpio";
 		pinctrl-0 = <&pinctrl_gpio_spi>;
 		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		/* PTD12 ->RPIO[91] */
-		sck-gpios  = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		sck-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
 		/* PTD10 ->RPIO[89] */
 		miso-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <0>;
@@ -79,7 +79,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			/* PTB18 -> RGPIO[40] */
-			load-gpios  = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			load-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			spi-max-frequency = <100000>;
 		};
 	};
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/vf/vf610-colibri-eval-v3.dts
new file mode 100644
index 000000000000..fb661e8a2dc6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf610-colibri-eval-v3.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2014-2020 Toradex
+ */
+
+/dts-v1/;
+#include "vf610-colibri.dtsi"
+#include "vf-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri VF61 on Colibri Evaluation Board";
+	compatible = "toradex,vf610-colibri_vf61-on-eval", "toradex,vf610-colibri_vf61", "fsl,vf610";
+};
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf610-colibri.dtsi
new file mode 100644
index 000000000000..607cec2df861
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf610-colibri.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2014-2020 Toradex
+ */
+
+#include "vf610.dtsi"
+#include "vf-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri VF61 COM";
+	compatible = "toradex,vf610-colibri_vf61", "fsl,vf610";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&nfc {
+	assigned-clocks = <&clks VF610_CLK_NFC>;
+	assigned-clock-rates = <50000000>;
+};
diff --git a/arch/arm/boot/dts/vf610-cosmic.dts b/arch/arm/boot/dts/nxp/vf/vf610-cosmic.dts
index 703f375d7e24..703f375d7e24 100644
--- a/arch/arm/boot/dts/vf610-cosmic.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-cosmic.dts
diff --git a/arch/arm/boot/dts/vf610-pinfunc.h b/arch/arm/boot/dts/nxp/vf/vf610-pinfunc.h
index f1e5a7cf58a9..b7b7322a2d1b 100644
--- a/arch/arm/boot/dts/vf610-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/vf/vf610-pinfunc.h
@@ -420,7 +420,7 @@
 #define VF610_PAD_PTD29__FTM3_CH2		0x104 0x000 ALT4 0x0
 #define VF610_PAD_PTD29__DSPI2_SIN		0x104 0x000 ALT5 0x0
 #define VF610_PAD_PTD29__DEBUG_OUT11		0x104 0x000 ALT7 0x0
-#define VF610_PAD_PTD28__GPIO_66	 	0x108 0x000 ALT0 0x0
+#define VF610_PAD_PTD28__GPIO_66		0x108 0x000 ALT0 0x0
 #define VF610_PAD_PTD28__FB_AD28		0x108 0x000 ALT1 0x0
 #define VF610_PAD_PTD28__NF_IO12		0x108 0x000 ALT2 0x0
 #define VF610_PAD_PTD28__I2C2_SCL		0x108 0x34C ALT3 0x1
@@ -802,5 +802,55 @@
 #define VF610_PAD_PTE28__EWM_OUT		0x214 0x000 ALT7 0x0
 #define VF610_PAD_PTA7__GPIO_134		0x218 0x000 ALT0 0x0
 #define VF610_PAD_PTA7__VIU_PIX_CLK		0x218 0x3AC ALT1 0x1
+#define VF610_PAD_DDR_RESETB			0x21c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A15__DDR_A_15		0x220 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A14__DDR_A_14		0x224 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A13__DDR_A_13		0x228 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A12__DDR_A_12		0x22c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A11__DDR_A_11		0x230 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A10__DDR_A_10		0x234 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A9__DDR_A_9		0x238 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A8__DDR_A_8		0x23c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A7__DDR_A_7		0x240 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A6__DDR_A_6		0x244 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A5__DDR_A_5		0x248 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A4__DDR_A_4		0x24c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A3__DDR_A_3		0x250 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A2__DDR_A_2		0x254 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A1__DDR_A_1		0x258 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A0__DDR_A_0		0x25c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA2__DDR_BA_2		0x260 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA1__DDR_BA_1		0x264 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA0__DDR_BA_0		0x268 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CAS__DDR_CAS_B		0x26c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CKE__DDR_CKE_0		0x270 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CLK__DDR_CLK_0		0x274 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CS__DDR_CS_B_0		0x278 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D15__DDR_D_15		0x27c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D14__DDR_D_14		0x280 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D13__DDR_D_13		0x284 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D12__DDR_D_12		0x288 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D11__DDR_D_11		0x28c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D10__DDR_D_10		0x290 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D9__DDR_D_9		0x294 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D8__DDR_D_8		0x298 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D7__DDR_D_7		0x29c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D6__DDR_D_6		0x2a0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D5__DDR_D_5		0x2a4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D4__DDR_D_4		0x2a8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D3__DDR_D_3		0x2ac 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D2__DDR_D_2		0x2b0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D1__DDR_D_1		0x2b4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D0__DDR_D_0		0x2b8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQM1__DDR_DQM_1		0x2bc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQM0__DDR_DQM_0		0x2c0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQS1__DDR_DQS_1		0x2c4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQS0__DDR_DQS_0		0x2c8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_RAS__DDR_RAS_B		0x2cc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_WE__DDR_WE_B		0x2d0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_ODT1__DDR_ODT_0		0x2d4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_ODT0__DDR_ODT_1		0x2d8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DDRBYTE1__DDR_DDRBYTE1	0x2dc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DDRBYTE2__DDR_DDRBYTE2	0x2e0 0x000 ALT0 0x0
 
 #endif
diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/nxp/vf/vf610-twr.dts
index dbb5ffcdcec4..876c14ecceb6 100644
--- a/arch/arm/boot/dts/vf610-twr.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-twr.dts
@@ -30,27 +30,20 @@
 		clock-frequency = <50000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_vcc_3v3_mcu: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vcc_3v3_mcu";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_mcu";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 	};
 
 	sound {
@@ -169,7 +162,7 @@
 	       VDDA-supply = <&reg_3p3v>;
 	       VDDIO-supply = <&reg_3p3v>;
 	       clocks = <&clks VF610_CLK_SAI2>;
-       };
+	};
 };
 
 &iomuxc {
diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
index 28732249cfc0..7e72f860c3c5 100644
--- a/arch/arm/boot/dts/vf610-zii-cfu1.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
@@ -71,6 +71,14 @@
 		los-gpio = <&gpio4 4 GPIO_ACTIVE_HIGH>;
 		tx-disable-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 	};
+
+	supply-voltage-monitor {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 8>, /* 28VDC_IN */
+			      <&adc0 9>, /* +3.3V    */
+			      <&adc1 8>, /* VCC_1V5  */
+			      <&adc1 9>; /* VCC_1V2  */
+	};
 };
 
 &adc0 {
@@ -150,9 +158,11 @@
 	mdio1: mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clock-frequency = <12500000>;
+		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6085";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_switch>;
@@ -162,28 +172,27 @@
 			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
-			reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_fc_1000_1";
 					phy-mode = "1000base-x";
@@ -191,9 +200,9 @@
 					sfp = <&sff>;
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -216,6 +225,7 @@
 		compatible = "nxp,pca9554";
 		reg = <0x22>;
 		gpio-controller;
+		#gpio-cells = <2>;
 	};
 
 	lm75@48 {
@@ -346,7 +356,6 @@
 	pinctrl_switch: switch-grp {
 		fsl,pins = <
 			VF610_PAD_PTB28__GPIO_98		0x3061
-			VF610_PAD_PTE2__GPIO_107		0x1042
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-b.dts
index 48086c5e8549..b0ed68af0546 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-b.dts
@@ -75,7 +75,7 @@
 
 					port@6 {
 						reg = <6>;
-						label = "cpu";
+						phy-mode = "rmii";
 						ethernet = <&fec1>;
 
 						fixed-link {
@@ -149,7 +149,7 @@
 						reg = <5>;
 						label = "dsa";
 						link = <&switch2port9>;
-						phy-mode = "rgmii-txid";
+						phy-mode = "1000base-x";
 
 						fixed-link {
 							speed = <1000>;
@@ -211,12 +211,14 @@
 						reg = <0>;
 						label = "lan6";
 						phy-handle = <&switch2phy0>;
+						phy-mode = "sgmii";
 					};
 
 					port@1 {
 						reg = <1>;
 						label = "lan7";
 						phy-handle = <&switch2phy1>;
+						phy-mode = "sgmii";
 					};
 
 					port@2 {
@@ -252,7 +254,7 @@
 					switch2port9: port@9 {
 						reg = <9>;
 						label = "dsa";
-						phy-mode = "rgmii-txid";
+						phy-mode = "1000base-x";
 						link = <&switch1port5
 							&switch0port5>;
 
@@ -286,17 +288,17 @@
 		};
 	};
 
-	spi0 {
+	spi-0 {
 		compatible = "spi-gpio";
 		pinctrl-0 = <&pinctrl_gpio_spi0>;
 		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		gpio-sck  = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 11 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		cs-gpios  = <&gpio1  9 GPIO_ACTIVE_LOW
-			     &gpio1  8 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 9 GPIO_ACTIVE_LOW
+			    &gpio1 8 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <2>;
 
 		flash@0 {
@@ -311,8 +313,6 @@
 			compatible = "atmel,at93c46d";
 			pinctrl-0 = <&pinctrl_gpio_e6185_eeprom_sel>;
 			pinctrl-names = "default";
-			#address-cells = <0>;
-			#size-cells = <0>;
 			reg = <1>;
 			spi-max-frequency = <500000>;
 			spi-cs-high;
@@ -323,11 +323,6 @@
 };
 
 &i2c0 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c0>;
-	status = "okay";
-
 	gpio5: io-expander@20 {
 		compatible = "nxp,pca9554";
 		reg = <0x20>;
@@ -350,12 +345,7 @@
 };
 
 &i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
@@ -416,6 +406,9 @@
 	};
 };
 
+&mdio1 {
+	clock-frequency = <5000000>;
+};
 
 &iomuxc {
 	pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 {
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-c.dts
index 778e02c000d1..6f9878f124c4 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-c.dts
@@ -44,7 +44,7 @@
 
 					port@0 {
 						reg = <0>;
-						label = "cpu";
+						phy-mode = "rmii";
 						ethernet = <&fec1>;
 
 						fixed-link {
@@ -82,6 +82,11 @@
 						label = "dsa";
 						phy-mode = "xaui";
 						link = <&switch1port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 
@@ -164,7 +169,7 @@
 					port@9 {
 						reg = <9>;
 						label = "sff2";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff2>;
 					};
@@ -174,6 +179,11 @@
 						label = "dsa";
 						phy-mode = "xaui";
 						link = <&switch0port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 				mdio {
@@ -259,7 +269,7 @@
 		xtal-trim = /bits/ 8 <0x06>;
 
 		sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
-		reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+		reset-gpio = <&gpio6 10 GPIO_ACTIVE_LOW>;
 
 		fsl,spi-cs-sck-delay = <180>;
 		fsl,spi-sck-cs-delay = <250>;
@@ -340,7 +350,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/vf610-zii-dev.dtsi b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev.dtsi
index a1b4ccee2a10..ce5e52896b19 100644
--- a/arch/arm/boot/dts/vf610-zii-dev.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev.dtsi
@@ -59,7 +59,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -84,6 +84,14 @@
 		regulator-boot-on;
 		gpio = <&gpio0 6 0>;
 	};
+
+	supply-voltage-monitor {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 8>, /* VCC_1V5 */
+			      <&adc0 9>, /* VCC_1V8 */
+			      <&adc1 8>, /* VCC_1V0 */
+			      <&adc1 9>; /* VCC_1V2 */
+	};
 };
 
 &adc0 {
@@ -129,6 +137,8 @@
 	mdio1: mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clock-frequency = <12500000>;
+		suppress-preamble;
 		status = "okay";
 	};
 };
diff --git a/arch/arm/boot/dts/vf610-zii-scu4-aib.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
index d7caf618f980..77492eeea450 100644
--- a/arch/arm/boot/dts/vf610-zii-scu4-aib.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
@@ -23,7 +23,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -47,19 +47,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0: switch0@0 {
+			switch0: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 0>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
+					ethernet-port@0 {
 						reg = <0>;
-						label = "cpu";
+						phy-mode = "rmii";
 						ethernet = <&fec1>;
 
 						fixed-link {
@@ -68,37 +68,37 @@
 						};
 					};
 
-					port@1 {
+					ethernet-port@1 {
 						reg = <1>;
 						label = "aib2main_1";
 					};
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "aib2main_2";
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_cu_1000_5";
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_cu_1000_6";
 					};
 
-					port@5 {
+					ethernet-port@5 {
 						reg = <5>;
 						label = "eth_cu_1000_4";
 					};
 
-					port@6 {
+					ethernet-port@6 {
 						reg = <6>;
 						label = "eth_cu_1000_7";
 					};
 
-					port@7 {
+					ethernet-port@7 {
 						reg = <7>;
 						label = "modem_pic";
 
@@ -108,13 +108,18 @@
 						};
 					};
 
-					switch0port10: port@10 {
+					switch0port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch1port10
 							&switch3port10
 							&switch2port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -125,44 +130,54 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch1: switch1@0 {
+			switch1: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 1>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@1 {
+					ethernet-port@1 {
 						reg = <1>;
 						label = "eth_cu_1000_3";
 					};
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_cu_100_2";
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_cu_100_3";
 					};
 
-					switch1port9: port@9 {
+					switch1port9: ethernet-port@9 {
 						reg = <9>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch3port10
 							&switch2port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 
-					switch1port10: port@10 {
+					switch1port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch0port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -173,79 +188,84 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch2: switch2@0 {
+			switch2: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 2>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_fc_1000_2";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff1>;
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_fc_1000_3";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff2>;
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_fc_1000_4";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff3>;
 					};
 
-					port@5 {
+					ethernet-port@5 {
 						reg = <5>;
 						label = "eth_fc_1000_5";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff4>;
 					};
 
-					port@6 {
+					ethernet-port@6 {
 						reg = <6>;
 						label = "eth_fc_1000_6";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff5>;
 					};
 
-					port@7 {
+					ethernet-port@7 {
 						reg = <7>;
 						label = "eth_fc_1000_7";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff6>;
 					};
 
-					port@9 {
+					ethernet-port@9 {
 						reg = <9>;
 						label = "eth_fc_1000_1";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff0>;
 					};
 
-					switch2port10: port@10 {
+					switch2port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "2500base-x";
 						link = <&switch3port9
 							&switch1port9
 							&switch0port10>;
+
+						fixed-link {
+							speed = <2500>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -256,53 +276,63 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch3: switch3@0 {
+			switch3: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 3>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_fc_1000_8";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff7>;
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_fc_1000_9";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff8>;
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_fc_1000_10";
-						phy-mode = "sgmii";
+						phy-mode = "1000base-x";
 						managed = "in-band-status";
 						sfp = <&sff9>;
 					};
 
-					switch3port9: port@9 {
+					switch3port9: ethernet-port@9 {
 						reg = <9>;
 						label = "dsa";
 						phy-mode = "2500base-x";
 						link = <&switch2port10>;
+
+						fixed-link {
+							speed = <2500>;
+							full-duplex;
+						};
 					};
 
-					switch3port10: port@10 {
+					switch3port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch1port9
 							&switch0port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -407,7 +437,7 @@
 	pinctrl-0 = <&pinctrl_dspi1>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -420,7 +450,7 @@
 		};
 	};
 
-	spi-flash@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -509,7 +539,7 @@
 		#gpio-cells = <2>;
 	};
 
-	lm75@48 {
+	temp-sensor@48 {
 		compatible = "national,lm75";
 		reg = <0x48>;
 	};
@@ -524,7 +554,7 @@
 		reg = <0x52>;
 	};
 
-	ds1682@6b {
+	elapsed-time-recorder@6b {
 		compatible = "dallas,ds1682";
 		reg = <0x6b>;
 	};
@@ -536,7 +566,12 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	adt7411@4a {
+	watchdog@38 {
+		compatible = "zii,rave-wdt";
+		reg = <0x38>;
+	};
+
+	adc@4a {
 		compatible = "adi,adt7411";
 		reg = <0x4a>;
 	};
@@ -548,7 +583,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	gpio9: sx1503q@20 {
+	gpio9: io-expander@20 {
 		compatible = "semtech,sx1503q";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sx1503_20>;
@@ -559,12 +594,12 @@
 		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
 	};
 
-	lm75@4e {
+	temp-sensor@4e {
 		compatible = "national,lm75";
 		reg = <0x4e>;
 	};
 
-	lm75@4f {
+	temp-sensor@4f {
 		compatible = "national,lm75";
 		reg = <0x4f>;
 	};
@@ -576,17 +611,17 @@
 		reg = <0x23>;
 	};
 
-	adt7411@4a {
+	adc@4a {
 		compatible = "adi,adt7411";
 		reg = <0x4a>;
 	};
 
-	at24c08@54 {
+	eeprom@54 {
 		compatible = "atmel,24c08";
 		reg = <0x54>;
 	};
 
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-names = "default";
 		#address-cells = <1>;
@@ -625,7 +660,7 @@
 		};
 	};
 
-	tca9548@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		pinctrl-names = "default";
 		reg = <0x71>;
diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
index 77e1484211e4..2a490464660c 100644
--- a/arch/arm/boot/dts/vf610-zii-spb4.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
@@ -42,6 +42,14 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	supply-voltage-monitor {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 8>, /* 28V_SW   */
+			      <&adc0 9>, /* +3.3V    */
+			      <&adc1 8>, /* VCC_1V5  */
+			      <&adc1 9>; /* VCC_1V2  */
+	};
 };
 
 &adc0 {
@@ -111,27 +119,28 @@
 	mdio1: mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clock-frequency = <12500000>;
+		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
 			reg = <0>;
 			eeprom-length = <65536>;
-			reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
 			interrupt-parent = <&gpio3>;
 			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -140,32 +149,32 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@4 {
+				ethernet-port@4 {
 					reg = <4>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_6";
 				};
@@ -199,6 +208,18 @@
 	};
 };
 
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	watchdog@38 {
+		compatible = "zii,rave-wdt";
+		reg = <0x38>;
+	};
+};
+
 &snvsrtc {
 	status = "disabled";
 };
@@ -220,7 +241,7 @@
 	pinctrl-0 = <&pinctrl_uart2>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -304,7 +325,6 @@
 
 	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
 		fsl,pins = <
-			VF610_PAD_PTE2__GPIO_107		0x31c2
 			VF610_PAD_PTB28__GPIO_98		0x219d
 		>;
 	};
@@ -316,6 +336,13 @@
 		>;
 	};
 
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			VF610_PAD_PTB16__I2C1_SCL		0x37ff
+			VF610_PAD_PTB17__I2C1_SDA		0x37ff
+		>;
+	};
+
 	pinctrl_leds_debug: pinctrl-leds-debug {
 		fsl,pins = <
 			VF610_PAD_PTD3__GPIO_82			0x31c2
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
index 847c5858fea1..078d8699e16d 100644
--- a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
@@ -46,6 +46,14 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	supply-voltage-monitor {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 8>, /* 12V_MAIN */
+			      <&adc0 9>, /* +3.3V    */
+			      <&adc1 8>, /* VCC_1V5  */
+			      <&adc1 9>; /* VCC_1V2  */
+	};
 };
 
 &adc0 {
@@ -73,6 +81,8 @@
 	non-removable;
 	no-1-8-v;
 	keep-power-in-suspend;
+	no-sdio;
+	no-sd;
 	status = "okay";
 };
 
@@ -80,6 +90,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
 	bus-width = <4>;
+	no-sdio;
 	status = "okay";
 };
 
@@ -97,27 +108,28 @@
 	mdio1: mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clock-frequency = <12500000>;
+		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
 			reg = <0>;
 			eeprom-length = <65536>;
-			reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
 			interrupt-parent = <&gpio3>;
 			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -126,27 +138,27 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_100_3";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@8 {
+				ethernet-port@8 {
 					reg = <8>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@9 {
+				ethernet-port@9 {
 					reg = <9>;
 					label = "eth_cu_1000_2";
 					phy-handle = <&phy9>;
@@ -155,12 +167,12 @@
 				};
 			};
 
-			mdio1 {
+			mdio-external {
 				compatible = "marvell,mv88e6xxx-mdio-external";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				phy9: phy9@0 {
+				phy9: ethernet-phy@0 {
 					compatible = "ethernet-phy-ieee802.3-c45";
 					pinctrl-0 = <&pinctrl_gpio_phy9>;
 					pinctrl-names = "default";
@@ -280,7 +292,6 @@
 
 	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
 		fsl,pins = <
-			VF610_PAD_PTE2__GPIO_107		0x31c2
 			VF610_PAD_PTB28__GPIO_98		0x219d
 		>;
 	};
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
index 453fce80f858..22c8f44390a9 100644
--- a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
@@ -46,6 +46,14 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	supply-voltage-monitor {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 8>, /* 12V_MAIN */
+			      <&adc0 9>, /* +3.3V    */
+			      <&adc1 8>, /* VCC_1V5  */
+			      <&adc1 9>; /* VCC_1V2  */
+	};
 };
 
 &adc0 {
@@ -125,27 +133,28 @@
 	mdio1: mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clock-frequency = <12500000>;
+		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
 			reg = <0>;
 			eeprom-length = <65536>;
-			reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
 			interrupt-parent = <&gpio3>;
 			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -154,32 +163,32 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@4 {
+				ethernet-port@4 {
 					reg = <4>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_6";
 				};
@@ -218,6 +227,18 @@
 	};
 };
 
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	watchdog@38 {
+		compatible = "zii,rave-wdt";
+		reg = <0x38>;
+	};
+};
+
 &snvsrtc {
 	status = "disabled";
 };
@@ -233,7 +254,7 @@
 	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -311,7 +332,6 @@
 
 	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
 		fsl,pins = <
-			VF610_PAD_PTE2__GPIO_107		0x31c2
 			VF610_PAD_PTB28__GPIO_98		0x219d
 		>;
 	};
diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/nxp/vf/vf610.dtsi
index 7fd39817f8ab..2fba923821d0 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610.dtsi
@@ -2,7 +2,6 @@
 //
 // Copyright 2013 Freescale Semiconductor, Inc.
 
-
 #include "vf500.dtsi"
 
 &a5_cpu {
@@ -10,7 +9,7 @@
 };
 
 &aips0 {
-	L2: l2-cache@40006000 {
+	L2: cache-controller@40006000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x40006000 0x1000>;
 		cache-unified;
diff --git a/arch/arm/boot/dts/nxp/vf/vf610m4-colibri.dts b/arch/arm/boot/dts/nxp/vf/vf610m4-colibri.dts
new file mode 100644
index 000000000000..2c2db47af441
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf610m4-colibri.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device tree for Colibri VF61 Cortex-M4 support
+ *
+ * Copyright (C) 2015 Stefan Agner
+ */
+
+/dts-v1/;
+#include "vf610m4.dtsi"
+
+/ {
+	model = "VF610 Cortex-M4";
+	compatible = "fsl,vf610m4";
+
+	chosen {
+		bootargs = "clk_ignore_unused init=/linuxrc rw";
+		stdout-path = "serial2:115200";
+	};
+
+	memory@8c000000 {
+		device_type = "memory";
+		reg = <0x8c000000 0x3000000>;
+	};
+};
+
+&gpio0 {
+	status = "disabled";
+};
+
+&gpio1 {
+	status = "disabled";
+};
+
+&gpio2 {
+	status = "disabled";
+};
+
+&gpio3 {
+	status = "disabled";
+};
+
+&gpio4 {
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&iomuxc {
+	vf610-colibri {
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				VF610_PAD_PTD0__UART2_TX		0x21a2
+				VF610_PAD_PTD1__UART2_RX		0x21a1
+				VF610_PAD_PTD2__UART2_RTS		0x21a2
+				VF610_PAD_PTD3__UART2_CTS		0x21a1
+			>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/vf610m4-cosmic.dts b/arch/arm/boot/dts/nxp/vf/vf610m4-cosmic.dts
index f7474c11aabd..f7474c11aabd 100644
--- a/arch/arm/boot/dts/vf610m4-cosmic.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610m4-cosmic.dts
diff --git a/arch/arm/boot/dts/vf610m4.dtsi b/arch/arm/boot/dts/nxp/vf/vf610m4.dtsi
index 76bbfd5e32b6..2bb331a87721 100644
--- a/arch/arm/boot/dts/vf610m4.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610m4.dtsi
@@ -42,7 +42,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../../armv7-m.dtsi"
 #include "vfxxx.dtsi"
 
 / {
diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/nxp/vf/vfxxx.dtsi
index 028e0ec30e0c..acccf9a3c898 100644
--- a/arch/arm/boot/dts/vfxxx.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vfxxx.dtsi
@@ -59,7 +59,7 @@
 		interrupt-parent = <&mscm_ir>;
 		ranges;
 
-		aips0: aips-bus@40000000 {
+		aips0: bus@40000000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -95,7 +95,7 @@
 				status = "disabled";
 			};
 
-			can0: flexcan@40020000 {
+			can0: can@40020000 {
 				compatible = "fsl,vf610-flexcan";
 				reg = <0x40020000 0x4000>;
 				interrupts = <58 IRQ_TYPE_LEVEL_HIGH>;
@@ -111,8 +111,7 @@
 				interrupts = <61 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART0>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 2>,
-					<&edma0 0 3>;
+				dmas = <&edma0 0 2>, <&edma0 0 3>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -123,8 +122,7 @@
 				interrupts = <62 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART1>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 4>,
-					<&edma0 0 5>;
+				dmas = <&edma0 0 4>, <&edma0 0 5>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -135,8 +133,7 @@
 				interrupts = <63 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART2>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 6>,
-					<&edma0 0 7>;
+				dmas = <&edma0 0 6>, <&edma0 0 7>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -147,8 +144,7 @@
 				interrupts = <64 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART3>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 8>,
-					<&edma0 0 9>;
+				dmas = <&edma0 0 8>, <&edma0 0 9>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -162,8 +158,7 @@
 				clocks = <&clks VF610_CLK_DSPI0>;
 				clock-names = "dspi";
 				spi-num-chipselects = <6>;
-				dmas = <&edma1 1 12>,
-					<&edma1 1 13>;
+				dmas = <&edma1 1 12>, <&edma1 1 13>;
 				dma-names = "rx", "tx";
 				status = "disabled";
 			};
@@ -177,8 +172,7 @@
 				clocks = <&clks VF610_CLK_DSPI1>;
 				clock-names = "dspi";
 				spi-num-chipselects = <4>;
-				dmas = <&edma1 1 14>,
-					<&edma1 1 15>;
+				dmas = <&edma1 1 14>, <&edma1 1 15>;
 				dma-names = "rx", "tx";
 				status = "disabled";
 			};
@@ -191,9 +185,8 @@
 					<&clks VF610_CLK_SAI0_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 0 17>,
-					<&edma0 0 16>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 0 16>, <&edma0 0 17>;
 				status = "disabled";
 			};
 
@@ -205,9 +198,8 @@
 					<&clks VF610_CLK_SAI1_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 0 19>,
-					<&edma0 0 18>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 0 18>, <&edma0 0 19>;
 				status = "disabled";
 			};
 
@@ -219,9 +211,8 @@
 					<&clks VF610_CLK_SAI2_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 0 21>,
-					<&edma0 0 20>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 0 20>, <&edma0 0 21>;
 				status = "disabled";
 			};
 
@@ -233,9 +224,8 @@
 					<&clks VF610_CLK_SAI3_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 1 9>,
-					<&edma0 1 8>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 1 8>, <&edma0 1 9>;
 				status = "disabled";
 			};
 
@@ -293,12 +283,11 @@
 				status = "disabled";
 			};
 
-			wdoga5: wdog@4003e000 {
+			wdoga5: watchdog@4003e000 {
 				compatible = "fsl,vf610-wdt", "fsl,imx21-wdt";
 				reg = <0x4003e000 0x1000>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_WDT>;
-				clock-names = "wdog";
 				status = "disabled";
 			};
 
@@ -431,8 +420,7 @@
 				interrupts = <72 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_I2C1>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 52>,
-					<&edma0 0 53>;
+				dmas = <&edma0 0 52>, <&edma0 0 53>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -471,7 +459,7 @@
 			};
 		};
 
-		aips1: aips-bus@40080000 {
+		aips1: bus@40080000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -495,7 +483,7 @@
 			};
 
 			ocotp: ocotp@400a5000 {
-				compatible = "fsl,vf610-ocotp";
+				compatible = "fsl,vf610-ocotp", "syscon";
 				reg = <0x400a5000 0x1000>;
 				clocks = <&clks VF610_CLK_OCOTP>;
 			};
@@ -556,8 +544,7 @@
 				clocks = <&clks VF610_CLK_DSPI3>;
 				clock-names = "dspi";
 				spi-num-chipselects = <2>;
-				dmas = <&edma1 0 12>,
-					<&edma1 0 13>;
+				dmas = <&edma1 0 12>, <&edma1 0 13>;
 				dma-names = "rx", "tx";
 				status = "disabled";
 			};
@@ -574,7 +561,7 @@
 							<20000000>;
 			};
 
-			esdhc0: esdhc@400b1000 {
+			esdhc0: mmc@400b1000 {
 				compatible = "fsl,imx53-esdhc";
 				reg = <0x400b1000 0x1000>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
@@ -585,7 +572,7 @@
 				status = "disabled";
 			};
 
-			esdhc1: esdhc@400b2000 {
+			esdhc1: mmc@400b2000 {
 				compatible = "fsl,imx53-esdhc";
 				reg = <0x400b2000 0x1000>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
@@ -681,7 +668,7 @@
 				status = "disabled";
 			};
 
-			can1: flexcan@400d4000 {
+			can1: can@400d4000 {
 				compatible = "fsl,vf610-flexcan";
 				reg = <0x400d4000 0x4000>;
 				interrupts = <59 IRQ_TYPE_LEVEL_HIGH>;
@@ -724,11 +711,32 @@
 				interrupts = <74 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_I2C3>;
 				clock-names = "ipg";
-				dmas = <&edma0 1 38>,
-					<&edma0 1 39>;
+				dmas = <&edma0 1 38>, <&edma0 1 39>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
+
+			crypto: crypto@400f0000 {
+				compatible = "fsl,sec-v4.0";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0x400f0000 0x9000>;
+				ranges = <0 0x400f0000 0x9000>;
+				clocks = <&clks VF610_CLK_CAAM>;
+				clock-names = "ipg";
+
+				sec_jr0: jr0@1000 {
+					compatible = "fsl,sec-v4.0-job-ring";
+					reg = <0x1000 0x1000>;
+					interrupts = <102 IRQ_TYPE_LEVEL_HIGH>;
+				};
+
+				sec_jr1: jr1@2000 {
+					compatible = "fsl,sec-v4.0-job-ring";
+					reg = <0x2000 0x1000>;
+					interrupts = <102 IRQ_TYPE_LEVEL_HIGH>;
+				};
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/omap3-cpu-thermal.dtsi b/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
deleted file mode 100644
index 235ecfd61e2d..000000000000
--- a/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
+++ /dev/null
@@ -1,20 +0,0 @@
-/*
- * Device Tree Source for OMAP3 SoC CPU thermal
- *
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <dt-bindings/thermal/thermal.h>
-
-cpu_thermal: cpu_thermal {
-	polling-delay-passive = <250>; /* milliseconds */
-	polling-delay = <1000>; /* milliseconds */
-	coefficients = <0 20000>;
-
-			/* sensor       ID */
-	thermal-sensors = <&bandgap     0>;
-};
diff --git a/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi b/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
deleted file mode 100644
index 21079cdf2663..000000000000
--- a/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
+++ /dev/null
@@ -1,265 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Device Tree Source for OMAP34XX/OMAP36XX clock data
- *
- * Copyright (C) 2013 Texas Instruments, Inc.
- */
-&cm_clocks {
-	security_l4_ick2: security_l4_ick2 {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	aes1_ick: aes1_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		ti,bit-shift = <3>;
-		reg = <0x0a14>;
-	};
-
-	rng_ick: rng_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <2>;
-	};
-
-	sha11_ick: sha11_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <1>;
-	};
-
-	des1_ick: des1_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <0>;
-	};
-
-	cam_mclk: cam_mclk@f00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m5x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0f00>;
-		ti,set-rate-parent;
-	};
-
-	cam_ick: cam_ick@f10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&l4_ick>;
-		reg = <0x0f10>;
-		ti,bit-shift = <0>;
-	};
-
-	csi2_96m_fck: csi2_96m_fck@f00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0f00>;
-		ti,bit-shift = <1>;
-	};
-
-	security_l3_ick: security_l3_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l3_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	pka_ick: pka_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l3_ick>;
-		reg = <0x0a14>;
-		ti,bit-shift = <4>;
-	};
-
-	icr_ick: icr_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <29>;
-	};
-
-	des2_ick: des2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <26>;
-	};
-
-	mspro_ick: mspro_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <23>;
-	};
-
-	mailboxes_ick: mailboxes_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <7>;
-	};
-
-	ssi_l4_ick: ssi_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	sr1_fck: sr1_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <6>;
-	};
-
-	sr2_fck: sr2_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <7>;
-	};
-
-	sr_l4_ick: sr_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	dpll2_fck: dpll2_fck@40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <19>;
-		ti,max-div = <7>;
-		reg = <0x0040>;
-		ti,index-starts-at-one;
-	};
-
-	dpll2_ck: dpll2_ck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-clock";
-		clocks = <&sys_ck>, <&dpll2_fck>;
-		reg = <0x0004>, <0x0024>, <0x0040>, <0x0034>;
-		ti,low-power-stop;
-		ti,lock;
-		ti,low-power-bypass;
-	};
-
-	dpll2_m2_ck: dpll2_m2_ck@44 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll2_ck>;
-		ti,max-div = <31>;
-		reg = <0x0044>;
-		ti,index-starts-at-one;
-	};
-
-	iva2_ck: iva2_ck@0 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&dpll2_m2_ck>;
-		reg = <0x0000>;
-		ti,bit-shift = <0>;
-	};
-
-	modem_fck: modem_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <31>;
-	};
-
-	sad2d_ick: sad2d_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <3>;
-	};
-
-	mad2d_ick: mad2d_ick@a18 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&l3_ick>;
-		reg = <0x0a18>;
-		ti,bit-shift = <3>;
-	};
-
-	mspro_fck: mspro_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <23>;
-	};
-};
-
-&cm_clockdomains {
-	cam_clkdm: cam_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&cam_ick>, <&csi2_96m_fck>;
-	};
-
-	iva2_clkdm: iva2_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&iva2_ck>;
-	};
-
-	dpll2_clkdm: dpll2_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll2_ck>;
-	};
-
-	wkup_clkdm: wkup_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>,
-			 <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>,
-			 <&gpt1_ick>, <&sr1_fck>, <&sr2_fck>;
-	};
-
-	d2d_clkdm: d2d_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&modem_fck>, <&sad2d_ick>, <&mad2d_ick>;
-	};
-
-	core_l4_clkdm: core_l4_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>,
-			 <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>,
-			 <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>,
-			 <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>,
-			 <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>,
-			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
-			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
-			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
-			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>,
-			 <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,
-			 <&rng_ick>, <&mspro_fck>;
-	};
-};
diff --git a/arch/arm/boot/dts/omap3xxx-clocks.dtsi b/arch/arm/boot/dts/omap3xxx-clocks.dtsi
deleted file mode 100644
index 0656c32439d2..000000000000
--- a/arch/arm/boot/dts/omap3xxx-clocks.dtsi
+++ /dev/null
@@ -1,1662 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Device Tree Source for OMAP3 clock data
- *
- * Copyright (C) 2013 Texas Instruments, Inc.
- */
-&prm_clocks {
-	virt_16_8m_ck: virt_16_8m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <16800000>;
-	};
-
-	osc_sys_ck: osc_sys_ck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&virt_12m_ck>, <&virt_13m_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_38_4m_ck>, <&virt_16_8m_ck>;
-		reg = <0x0d40>;
-	};
-
-	sys_ck: sys_ck@1270 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&osc_sys_ck>;
-		ti,bit-shift = <6>;
-		ti,max-div = <3>;
-		reg = <0x1270>;
-		ti,index-starts-at-one;
-	};
-
-	sys_clkout1: sys_clkout1@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&osc_sys_ck>;
-		reg = <0x0d70>;
-		ti,bit-shift = <7>;
-	};
-
-	dpll3_x2_ck: dpll3_x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll3_m2x2_ck: dpll3_m2x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m2_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_x2_ck: dpll4_x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	corex2_fck: corex2_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m2x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	wkup_l4_ick: wkup_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&sys_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-};
-
-&scm_clocks {
-	mcbsp5_mux_fck: mcbsp5_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <4>;
-		reg = <0x68>;
-	};
-
-	mcbsp5_fck: mcbsp5_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp5_gate_fck>, <&mcbsp5_mux_fck>;
-	};
-
-	mcbsp1_mux_fck: mcbsp1_mux_fck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x04>;
-	};
-
-	mcbsp1_fck: mcbsp1_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp1_gate_fck>, <&mcbsp1_mux_fck>;
-	};
-
-	mcbsp2_mux_fck: mcbsp2_mux_fck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <6>;
-		reg = <0x04>;
-	};
-
-	mcbsp2_fck: mcbsp2_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp2_gate_fck>, <&mcbsp2_mux_fck>;
-	};
-
-	mcbsp3_mux_fck: mcbsp3_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		reg = <0x68>;
-	};
-
-	mcbsp3_fck: mcbsp3_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp3_gate_fck>, <&mcbsp3_mux_fck>;
-	};
-
-	mcbsp4_mux_fck: mcbsp4_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x68>;
-	};
-
-	mcbsp4_fck: mcbsp4_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp4_gate_fck>, <&mcbsp4_mux_fck>;
-	};
-};
-&cm_clocks {
-	dummy_apb_pclk: dummy_apb_pclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0x0>;
-	};
-
-	omap_32k_fck: omap_32k_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <32768>;
-	};
-
-	virt_12m_ck: virt_12m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <12000000>;
-	};
-
-	virt_13m_ck: virt_13m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <13000000>;
-	};
-
-	virt_19200000_ck: virt_19200000_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <19200000>;
-	};
-
-	virt_26000000_ck: virt_26000000_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <26000000>;
-	};
-
-	virt_38_4m_ck: virt_38_4m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <38400000>;
-	};
-
-	dpll4_ck: dpll4_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-per-clock";
-		clocks = <&sys_ck>, <&sys_ck>;
-		reg = <0x0d00>, <0x0d20>, <0x0d44>, <0x0d30>;
-	};
-
-	dpll4_m2_ck: dpll4_m2_ck@d48 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <63>;
-		reg = <0x0d48>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m2x2_mul_ck: dpll4_m2x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m2_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_m2x2_ck: dpll4_m2x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m2x2_mul_ck>;
-		ti,bit-shift = <0x1b>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	omap_96m_alwon_fck: omap_96m_alwon_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m2x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	dpll3_ck: dpll3_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-core-clock";
-		clocks = <&sys_ck>, <&sys_ck>;
-		reg = <0x0d00>, <0x0d20>, <0x0d40>, <0x0d30>;
-	};
-
-	dpll3_m3_ck: dpll3_m3_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll3_ck>;
-		ti,bit-shift = <16>;
-		ti,max-div = <31>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	dpll3_m3x2_mul_ck: dpll3_m3x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m3_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll3_m3x2_ck: dpll3_m3x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll3_m3x2_mul_ck>;
-		ti,bit-shift = <0xc>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	emu_core_alwon_ck: emu_core_alwon_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m3x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	sys_altclk: sys_altclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0x0>;
-	};
-
-	mcbsp_clks: mcbsp_clks {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0x0>;
-	};
-
-	dpll3_m2_ck: dpll3_m2_ck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll3_ck>;
-		ti,bit-shift = <27>;
-		ti,max-div = <31>;
-		reg = <0x0d40>;
-		ti,index-starts-at-one;
-	};
-
-	core_ck: core_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	dpll1_fck: dpll1_fck@940 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <19>;
-		ti,max-div = <7>;
-		reg = <0x0940>;
-		ti,index-starts-at-one;
-	};
-
-	dpll1_ck: dpll1_ck@904 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-clock";
-		clocks = <&sys_ck>, <&dpll1_fck>;
-		reg = <0x0904>, <0x0924>, <0x0940>, <0x0934>;
-	};
-
-	dpll1_x2_ck: dpll1_x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll1_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll1_x2m2_ck: dpll1_x2m2_ck@944 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll1_x2_ck>;
-		ti,max-div = <31>;
-		reg = <0x0944>;
-		ti,index-starts-at-one;
-	};
-
-	cm_96m_fck: cm_96m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_96m_alwon_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	omap_96m_fck: omap_96m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&cm_96m_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x0d40>;
-	};
-
-	dpll4_m3_ck: dpll4_m3_ck@e40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,bit-shift = <8>;
-		ti,max-div = <32>;
-		reg = <0x0e40>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m3x2_mul_ck: dpll4_m3x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m3_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_m3x2_ck: dpll4_m3x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m3x2_mul_ck>;
-		ti,bit-shift = <0x1c>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	omap_54m_fck: omap_54m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dpll4_m3x2_ck>, <&sys_altclk>;
-		ti,bit-shift = <5>;
-		reg = <0x0d40>;
-	};
-
-	cm_96m_d2_fck: cm_96m_d2_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&cm_96m_fck>;
-		clock-mult = <1>;
-		clock-div = <2>;
-	};
-
-	omap_48m_fck: omap_48m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&cm_96m_d2_fck>, <&sys_altclk>;
-		ti,bit-shift = <3>;
-		reg = <0x0d40>;
-	};
-
-	omap_12m_fck: omap_12m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_48m_fck>;
-		clock-mult = <1>;
-		clock-div = <4>;
-	};
-
-	dpll4_m4_ck: dpll4_m4_ck@e40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <16>;
-		reg = <0x0e40>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m4x2_mul_ck: dpll4_m4x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "ti,fixed-factor-clock";
-		clocks = <&dpll4_m4_ck>;
-		ti,clock-mult = <2>;
-		ti,clock-div = <1>;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m4x2_ck: dpll4_m4x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m4x2_mul_ck>;
-		ti,bit-shift = <0x1d>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m5_ck: dpll4_m5_ck@f40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <63>;
-		reg = <0x0f40>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m5x2_mul_ck: dpll4_m5x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "ti,fixed-factor-clock";
-		clocks = <&dpll4_m5_ck>;
-		ti,clock-mult = <2>;
-		ti,clock-div = <1>;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m5x2_ck: dpll4_m5x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m5x2_mul_ck>;
-		ti,bit-shift = <0x1e>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m6_ck: dpll4_m6_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,bit-shift = <24>;
-		ti,max-div = <63>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m6x2_mul_ck: dpll4_m6x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m6_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_m6x2_ck: dpll4_m6x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m6x2_mul_ck>;
-		ti,bit-shift = <0x1f>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	emu_per_alwon_ck: emu_per_alwon_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m6x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	clkout2_src_gate_ck: clkout2_src_gate_ck@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0d70>;
-	};
-
-	clkout2_src_mux_ck: clkout2_src_mux_ck@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_ck>, <&sys_ck>, <&cm_96m_fck>, <&omap_54m_fck>;
-		reg = <0x0d70>;
-	};
-
-	clkout2_src_ck: clkout2_src_ck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&clkout2_src_gate_ck>, <&clkout2_src_mux_ck>;
-	};
-
-	sys_clkout2: sys_clkout2@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&clkout2_src_ck>;
-		ti,bit-shift = <3>;
-		ti,max-div = <64>;
-		reg = <0x0d70>;
-		ti,index-power-of-two;
-	};
-
-	mpu_ck: mpu_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll1_x2m2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	arm_fck: arm_fck@924 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&mpu_ck>;
-		reg = <0x0924>;
-		ti,max-div = <2>;
-	};
-
-	emu_mpu_alwon_ck: emu_mpu_alwon_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&mpu_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	l3_ick: l3_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,max-div = <3>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
-	l4_ick: l4_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&l3_ick>;
-		ti,bit-shift = <2>;
-		ti,max-div = <3>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
-	rm_ick: rm_ick@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <1>;
-		ti,max-div = <3>;
-		reg = <0x0c40>;
-		ti,index-starts-at-one;
-	};
-
-	gpt10_gate_fck: gpt10_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <11>;
-		reg = <0x0a00>;
-	};
-
-	gpt10_mux_fck: gpt10_mux_fck@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x0a40>;
-	};
-
-	gpt10_fck: gpt10_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt10_gate_fck>, <&gpt10_mux_fck>;
-	};
-
-	gpt11_gate_fck: gpt11_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <12>;
-		reg = <0x0a00>;
-	};
-
-	gpt11_mux_fck: gpt11_mux_fck@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0a40>;
-	};
-
-	gpt11_fck: gpt11_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt11_gate_fck>, <&gpt11_mux_fck>;
-	};
-
-	core_96m_fck: core_96m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_96m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	mmchs2_fck: mmchs2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <25>;
-	};
-
-	mmchs1_fck: mmchs1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <24>;
-	};
-
-	i2c3_fck: i2c3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <17>;
-	};
-
-	i2c2_fck: i2c2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <16>;
-	};
-
-	i2c1_fck: i2c1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <15>;
-	};
-
-	mcbsp5_gate_fck: mcbsp5_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <10>;
-		reg = <0x0a00>;
-	};
-
-	mcbsp1_gate_fck: mcbsp1_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <9>;
-		reg = <0x0a00>;
-	};
-
-	core_48m_fck: core_48m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_48m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	mcspi4_fck: mcspi4_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <21>;
-	};
-
-	mcspi3_fck: mcspi3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <20>;
-	};
-
-	mcspi2_fck: mcspi2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <19>;
-	};
-
-	mcspi1_fck: mcspi1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <18>;
-	};
-
-	uart2_fck: uart2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <14>;
-	};
-
-	uart1_fck: uart1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <13>;
-	};
-
-	core_12m_fck: core_12m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_12m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	hdq_fck: hdq_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_12m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <22>;
-	};
-
-	core_l3_ick: core_l3_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l3_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	sdrc_ick: sdrc_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <1>;
-	};
-
-	gpmc_fck: gpmc_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&core_l3_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	core_l4_ick: core_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	mmchs2_ick: mmchs2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <25>;
-	};
-
-	mmchs1_ick: mmchs1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <24>;
-	};
-
-	hdq_ick: hdq_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <22>;
-	};
-
-	mcspi4_ick: mcspi4_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <21>;
-	};
-
-	mcspi3_ick: mcspi3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <20>;
-	};
-
-	mcspi2_ick: mcspi2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <19>;
-	};
-
-	mcspi1_ick: mcspi1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <18>;
-	};
-
-	i2c3_ick: i2c3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <17>;
-	};
-
-	i2c2_ick: i2c2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <16>;
-	};
-
-	i2c1_ick: i2c1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <15>;
-	};
-
-	uart2_ick: uart2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <14>;
-	};
-
-	uart1_ick: uart1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <13>;
-	};
-
-	gpt11_ick: gpt11_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <12>;
-	};
-
-	gpt10_ick: gpt10_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <11>;
-	};
-
-	mcbsp5_ick: mcbsp5_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <10>;
-	};
-
-	mcbsp1_ick: mcbsp1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <9>;
-	};
-
-	omapctrl_ick: omapctrl_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <6>;
-	};
-
-	dss_tv_fck: dss_tv_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&omap_54m_fck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <2>;
-	};
-
-	dss_96m_fck: dss_96m_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&omap_96m_fck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <2>;
-	};
-
-	dss2_alwon_fck: dss2_alwon_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <1>;
-	};
-
-	dummy_ck: dummy_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	gpt1_gate_fck: gpt1_gate_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0c00>;
-	};
-
-	gpt1_mux_fck: gpt1_mux_fck@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		reg = <0x0c40>;
-	};
-
-	gpt1_fck: gpt1_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt1_gate_fck>, <&gpt1_mux_fck>;
-	};
-
-	aes2_ick: aes2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		ti,bit-shift = <28>;
-		reg = <0x0a10>;
-	};
-
-	wkup_32k_fck: wkup_32k_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	gpio1_dbck: gpio1_dbck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&wkup_32k_fck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <3>;
-	};
-
-	sha12_ick: sha12_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <27>;
-	};
-
-	wdt2_fck: wdt2_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&wkup_32k_fck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <5>;
-	};
-
-	wdt2_ick: wdt2_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <5>;
-	};
-
-	wdt1_ick: wdt1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <4>;
-	};
-
-	gpio1_ick: gpio1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <3>;
-	};
-
-	omap_32ksync_ick: omap_32ksync_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <2>;
-	};
-
-	gpt12_ick: gpt12_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <1>;
-	};
-
-	gpt1_ick: gpt1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <0>;
-	};
-
-	per_96m_fck: per_96m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_96m_alwon_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	per_48m_fck: per_48m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_48m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	uart3_fck: uart3_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_48m_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <11>;
-	};
-
-	gpt2_gate_fck: gpt2_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x1000>;
-	};
-
-	gpt2_mux_fck: gpt2_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		reg = <0x1040>;
-	};
-
-	gpt2_fck: gpt2_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt2_gate_fck>, <&gpt2_mux_fck>;
-	};
-
-	gpt3_gate_fck: gpt3_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <4>;
-		reg = <0x1000>;
-	};
-
-	gpt3_mux_fck: gpt3_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x1040>;
-	};
-
-	gpt3_fck: gpt3_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt3_gate_fck>, <&gpt3_mux_fck>;
-	};
-
-	gpt4_gate_fck: gpt4_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <5>;
-		reg = <0x1000>;
-	};
-
-	gpt4_mux_fck: gpt4_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <2>;
-		reg = <0x1040>;
-	};
-
-	gpt4_fck: gpt4_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt4_gate_fck>, <&gpt4_mux_fck>;
-	};
-
-	gpt5_gate_fck: gpt5_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x1000>;
-	};
-
-	gpt5_mux_fck: gpt5_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x1040>;
-	};
-
-	gpt5_fck: gpt5_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt5_gate_fck>, <&gpt5_mux_fck>;
-	};
-
-	gpt6_gate_fck: gpt6_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x1000>;
-	};
-
-	gpt6_mux_fck: gpt6_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <4>;
-		reg = <0x1040>;
-	};
-
-	gpt6_fck: gpt6_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt6_gate_fck>, <&gpt6_mux_fck>;
-	};
-
-	gpt7_gate_fck: gpt7_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <8>;
-		reg = <0x1000>;
-	};
-
-	gpt7_mux_fck: gpt7_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <5>;
-		reg = <0x1040>;
-	};
-
-	gpt7_fck: gpt7_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt7_gate_fck>, <&gpt7_mux_fck>;
-	};
-
-	gpt8_gate_fck: gpt8_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <9>;
-		reg = <0x1000>;
-	};
-
-	gpt8_mux_fck: gpt8_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x1040>;
-	};
-
-	gpt8_fck: gpt8_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt8_gate_fck>, <&gpt8_mux_fck>;
-	};
-
-	gpt9_gate_fck: gpt9_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <10>;
-		reg = <0x1000>;
-	};
-
-	gpt9_mux_fck: gpt9_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x1040>;
-	};
-
-	gpt9_fck: gpt9_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt9_gate_fck>, <&gpt9_mux_fck>;
-	};
-
-	per_32k_alwon_fck: per_32k_alwon_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	gpio6_dbck: gpio6_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <17>;
-	};
-
-	gpio5_dbck: gpio5_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <16>;
-	};
-
-	gpio4_dbck: gpio4_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <15>;
-	};
-
-	gpio3_dbck: gpio3_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <14>;
-	};
-
-	gpio2_dbck: gpio2_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <13>;
-	};
-
-	wdt3_fck: wdt3_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <12>;
-	};
-
-	per_l4_ick: per_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	gpio6_ick: gpio6_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <17>;
-	};
-
-	gpio5_ick: gpio5_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <16>;
-	};
-
-	gpio4_ick: gpio4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <15>;
-	};
-
-	gpio3_ick: gpio3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <14>;
-	};
-
-	gpio2_ick: gpio2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <13>;
-	};
-
-	wdt3_ick: wdt3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <12>;
-	};
-
-	uart3_ick: uart3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <11>;
-	};
-
-	uart4_ick: uart4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <18>;
-	};
-
-	gpt9_ick: gpt9_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <10>;
-	};
-
-	gpt8_ick: gpt8_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <9>;
-	};
-
-	gpt7_ick: gpt7_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <8>;
-	};
-
-	gpt6_ick: gpt6_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <7>;
-	};
-
-	gpt5_ick: gpt5_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <6>;
-	};
-
-	gpt4_ick: gpt4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <5>;
-	};
-
-	gpt3_ick: gpt3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <4>;
-	};
-
-	gpt2_ick: gpt2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <3>;
-	};
-
-	mcbsp2_ick: mcbsp2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <0>;
-	};
-
-	mcbsp3_ick: mcbsp3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <1>;
-	};
-
-	mcbsp4_ick: mcbsp4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <2>;
-	};
-
-	mcbsp2_gate_fck: mcbsp2_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <0>;
-		reg = <0x1000>;
-	};
-
-	mcbsp3_gate_fck: mcbsp3_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <1>;
-		reg = <0x1000>;
-	};
-
-	mcbsp4_gate_fck: mcbsp4_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x1000>;
-	};
-
-	emu_src_mux_ck: emu_src_mux_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
-		reg = <0x1140>;
-	};
-
-	emu_src_ck: emu_src_ck {
-		#clock-cells = <0>;
-		compatible = "ti,clkdm-gate-clock";
-		clocks = <&emu_src_mux_ck>;
-	};
-
-	pclk_fck: pclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <8>;
-		ti,max-div = <7>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	pclkx2_fck: pclkx2_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <6>;
-		ti,max-div = <3>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	atclk_fck: atclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <4>;
-		ti,max-div = <3>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	traceclk_src_fck: traceclk_src_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
-		ti,bit-shift = <2>;
-		reg = <0x1140>;
-	};
-
-	traceclk_fck: traceclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&traceclk_src_fck>;
-		ti,bit-shift = <11>;
-		ti,max-div = <7>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	secure_32k_fck: secure_32k_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <32768>;
-	};
-
-	gpt12_fck: gpt12_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&secure_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	wdt1_fck: wdt1_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&secure_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-};
-
-&cm_clockdomains {
-	core_l3_clkdm: core_l3_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&sdrc_ick>;
-	};
-
-	dpll3_clkdm: dpll3_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll3_ck>;
-	};
-
-	dpll1_clkdm: dpll1_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll1_ck>;
-	};
-
-	per_clkdm: per_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&uart3_fck>, <&gpio6_dbck>, <&gpio5_dbck>,
-			 <&gpio4_dbck>, <&gpio3_dbck>, <&gpio2_dbck>,
-			 <&wdt3_fck>, <&gpio6_ick>, <&gpio5_ick>, <&gpio4_ick>,
-			 <&gpio3_ick>, <&gpio2_ick>, <&wdt3_ick>, <&uart3_ick>,
-			 <&uart4_ick>, <&gpt9_ick>, <&gpt8_ick>, <&gpt7_ick>,
-			 <&gpt6_ick>, <&gpt5_ick>, <&gpt4_ick>, <&gpt3_ick>,
-			 <&gpt2_ick>, <&mcbsp2_ick>, <&mcbsp3_ick>,
-			 <&mcbsp4_ick>;
-	};
-
-	emu_clkdm: emu_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&emu_src_ck>;
-	};
-
-	dpll4_clkdm: dpll4_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll4_ck>;
-	};
-
-	wkup_clkdm: wkup_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>,
-			 <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>,
-			 <&gpt1_ick>;
-	};
-
-	dss_clkdm: dss_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>;
-	};
-
-	core_l4_clkdm: core_l4_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>,
-			 <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>,
-			 <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>,
-			 <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>,
-			 <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>,
-			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
-			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
-			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
-			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>;
-	};
-};
diff --git a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi b/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
deleted file mode 100644
index ab7f87ae96f0..000000000000
--- a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Device Tree Source for OMAP4/5 SoC CPU thermal
- *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
- * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <dt-bindings/thermal/thermal.h>
-
-cpu_thermal: cpu_thermal {
-	polling-delay-passive = <250>; /* milliseconds */
-	polling-delay = <1000>; /* milliseconds */
-
-			/* sensor       ID */
-        thermal-sensors = <&bandgap     0>;
-
-	cpu_trips: trips {
-                cpu_alert0: cpu_alert {
-                        temperature = <100000>; /* millicelsius */
-                        hysteresis = <2000>; /* millicelsius */
-                        type = "passive";
-                };
-                cpu_crit: cpu_crit {
-                        temperature = <125000>; /* millicelsius */
-                        hysteresis = <2000>; /* millicelsius */
-                        type = "critical";
-                };
-        };
-
-	cpu_cooling_maps: cooling-maps {
-		map0 {
-			trip = <&cpu_alert0>;
-			cooling-device =
-				<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/omap4-droid-bionic-xt875.dts b/arch/arm/boot/dts/omap4-droid-bionic-xt875.dts
deleted file mode 100644
index ba5c35b7027d..000000000000
--- a/arch/arm/boot/dts/omap4-droid-bionic-xt875.dts
+++ /dev/null
@@ -1,9 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/dts-v1/;
-
-#include "motorola-mapphone-common.dtsi"
-
-/ {
-	model = "Motorola Droid Bionic XT875";
-	compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
-};
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
deleted file mode 100644
index c0d2fd92aea3..000000000000
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ /dev/null
@@ -1,9 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/dts-v1/;
-
-#include "motorola-mapphone-common.dtsi"
-
-/ {
-	model = "Motorola Droid 4 XT894";
-	compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
-};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
deleted file mode 100644
index 2de8a6b53de9..000000000000
--- a/arch/arm/boot/dts/omap4.dtsi
+++ /dev/null
@@ -1,470 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- */
-
-#include <dt-bindings/bus/ti-sysc.h>
-#include <dt-bindings/clock/omap4.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/omap.h>
-#include <dt-bindings/clock/omap4.h>
-
-/ {
-	compatible = "ti,omap4430", "ti,omap4";
-	interrupt-parent = <&wakeupgen>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-	chosen { };
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c2;
-		i2c2 = &i2c3;
-		i2c3 = &i2c4;
-		serial0 = &uart1;
-		serial1 = &uart2;
-		serial2 = &uart3;
-		serial3 = &uart4;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			compatible = "arm,cortex-a9";
-			device_type = "cpu";
-			next-level-cache = <&L2>;
-			reg = <0x0>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-		};
-		cpu@1 {
-			compatible = "arm,cortex-a9";
-			device_type = "cpu";
-			next-level-cache = <&L2>;
-			reg = <0x1>;
-		};
-	};
-
-	/*
-	 * Note that 4430 needs cross trigger interface (CTI) supported
-	 * before we can configure the interrupts. This means sampling
-	 * events are not supported for pmu. Note that 4460 does not use
-	 * CTI, see also 4460.dtsi.
-	 */
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		ti,hwmods = "debugss";
-	};
-
-	gic: interrupt-controller@48241000 {
-		compatible = "arm,cortex-a9-gic";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0x48241000 0x1000>,
-		      <0x48240100 0x0100>;
-		interrupt-parent = <&gic>;
-	};
-
-	L2: l2-cache-controller@48242000 {
-		compatible = "arm,pl310-cache";
-		reg = <0x48242000 0x1000>;
-		cache-unified;
-		cache-level = <2>;
-	};
-
-	local-timer@48240600 {
-		compatible = "arm,cortex-a9-twd-timer";
-		clocks = <&mpu_periphclk>;
-		reg = <0x48240600 0x20>;
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>;
-		interrupt-parent = <&gic>;
-	};
-
-	wakeupgen: interrupt-controller@48281000 {
-		compatible = "ti,omap4-wugen-mpu";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0x48281000 0x1000>;
-		interrupt-parent = <&gic>;
-	};
-
-	/*
-	 * The soc node represents the soc top level view. It is used for IPs
-	 * that are not memory mapped in the MPU view or for the MPU itself.
-	 */
-	soc {
-		compatible = "ti,omap-infra";
-		mpu {
-			compatible = "ti,omap4-mpu";
-			ti,hwmods = "mpu";
-			sram = <&ocmcram>;
-		};
-
-		dsp {
-			compatible = "ti,omap3-c64";
-			ti,hwmods = "dsp";
-		};
-
-		iva {
-			compatible = "ti,ivahd";
-			ti,hwmods = "iva";
-		};
-	};
-
-	/*
-	 * XXX: Use a flat representation of the OMAP4 interconnect.
-	 * The real OMAP interconnect network is quite complex.
-	 * Since it will not bring real advantage to represent that in DT for
-	 * the moment, just use a fake OCP bus entry to represent the whole bus
-	 * hierarchy.
-	 */
-	ocp {
-		compatible = "ti,omap4-l3-noc", "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
-		reg = <0x44000000 0x1000>,
-		      <0x44800000 0x2000>,
-		      <0x45000000 0x1000>;
-		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-
-		l4_wkup: interconnect@4a300000 {
-		};
-
-		l4_cfg: interconnect@4a000000 {
-		};
-
-		l4_per: interconnect@48000000 {
-		};
-
-		l4_abe: interconnect@40100000 {
-		};
-
-		ocmcram: sram@40304000 {
-			compatible = "mmio-sram";
-			reg = <0x40304000 0xa000>; /* 40k */
-		};
-
-		gpmc: gpmc@50000000 {
-			compatible = "ti,omap4430-gpmc";
-			reg = <0x50000000 0x1000>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma 4>;
-			dma-names = "rxtx";
-			gpmc,num-cs = <8>;
-			gpmc,num-waitpins = <4>;
-			ti,hwmods = "gpmc";
-			ti,no-idle-on-init;
-			clocks = <&l3_div_ck>;
-			clock-names = "fck";
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		mmu_dsp: mmu@4a066000 {
-			compatible = "ti,omap4-iommu";
-			reg = <0x4a066000 0x100>;
-			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu_dsp";
-			#iommu-cells = <0>;
-		};
-
-		target-module@52000000 {
-			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "iss";
-			reg = <0x52000000 0x4>,
-			      <0x52000010 0x4>;
-			reg-names = "rev", "sysc";
-			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
-			ti,sysc-midle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			ti,sysc-delay-us = <2>;
-			clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x52000000 0x1000000>;
-
-			/* No child device binding, driver in staging */
-		};
-
-		mmu_ipu: mmu@55082000 {
-			compatible = "ti,omap4-iommu";
-			reg = <0x55082000 0x100>;
-			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu_ipu";
-			#iommu-cells = <0>;
-			ti,iommu-bus-err-back;
-		};
-		target-module@4012c000 {
-			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "slimbus1";
-			reg = <0x4012c000 0x4>,
-			      <0x4012c010 0x4>;
-			reg-names = "rev", "sysc";
-			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			clocks = <&abe_clkctrl OMAP4_SLIMBUS1_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */
-				 <0x4902c000 0x4902c000 0x1000>; /* L3 */
-
-			/* No child device binding or driver in mainline */
-		};
-
-		dmm@4e000000 {
-			compatible = "ti,omap4-dmm";
-			reg = <0x4e000000 0x800>;
-			interrupts = <0 113 0x4>;
-			ti,hwmods = "dmm";
-		};
-
-		emif1: emif@4c000000 {
-			compatible = "ti,emif-4d";
-			reg = <0x4c000000 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "emif1";
-			ti,no-idle-on-init;
-			phy-type = <1>;
-			hw-caps-read-idle-ctrl;
-			hw-caps-ll-interface;
-			hw-caps-temp-alert;
-		};
-
-		emif2: emif@4d000000 {
-			compatible = "ti,emif-4d";
-			reg = <0x4d000000 0x100>;
-			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "emif2";
-			ti,no-idle-on-init;
-			phy-type = <1>;
-			hw-caps-read-idle-ctrl;
-			hw-caps-ll-interface;
-			hw-caps-temp-alert;
-		};
-
-		aes1: aes@4b501000 {
-			compatible = "ti,omap4-aes";
-			ti,hwmods = "aes1";
-			reg = <0x4b501000 0xa0>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma 111>, <&sdma 110>;
-			dma-names = "tx", "rx";
-		};
-
-		aes2: aes@4b701000 {
-			compatible = "ti,omap4-aes";
-			ti,hwmods = "aes2";
-			reg = <0x4b701000 0xa0>;
-			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma 114>, <&sdma 113>;
-			dma-names = "tx", "rx";
-		};
-
-		des: des@480a5000 {
-			compatible = "ti,omap4-des";
-			ti,hwmods = "des";
-			reg = <0x480a5000 0xa0>;
-			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma 117>, <&sdma 116>;
-			dma-names = "tx", "rx";
-		};
-
-		sham: sham@4b100000 {
-			compatible = "ti,omap4-sham";
-			ti,hwmods = "sham";
-			reg = <0x4b100000 0x300>;
-			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma 119>;
-			dma-names = "rx";
-		};
-
-		abb_mpu: regulator-abb-mpu {
-			compatible = "ti,abb-v2";
-			regulator-name = "abb_mpu";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			ti,tranxdone-status-mask = <0x80>;
-			clocks = <&sys_clkin_ck>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			status = "disabled";
-		};
-
-		abb_iva: regulator-abb-iva {
-			compatible = "ti,abb-v2";
-			regulator-name = "abb_iva";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			ti,tranxdone-status-mask = <0x80000000>;
-			clocks = <&sys_clkin_ck>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			status = "disabled";
-		};
-
-		target-module@56000000 {
-			compatible = "ti,sysc-omap4", "ti,sysc";
-			reg = <0x5600fe00 0x4>,
-			      <0x5600fe10 0x4>;
-			reg-names = "rev", "sysc";
-			ti,sysc-midle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x56000000 0x2000000>;
-
-			/*
-			 * Closed source PowerVR driver, no child device
-			 * binding or driver in mainline
-			 */
-		};
-
-		dss: dss@58000000 {
-			compatible = "ti,omap4-dss";
-			reg = <0x58000000 0x80>;
-			status = "disabled";
-			ti,hwmods = "dss_core";
-			clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			dispc@58001000 {
-				compatible = "ti,omap4-dispc";
-				reg = <0x58001000 0x1000>;
-				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
-				ti,hwmods = "dss_dispc";
-				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
-				clock-names = "fck";
-			};
-
-			rfbi: encoder@58002000  {
-				compatible = "ti,omap4-rfbi";
-				reg = <0x58002000 0x1000>;
-				status = "disabled";
-				ti,hwmods = "dss_rfbi";
-				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, <&l3_div_ck>;
-				clock-names = "fck", "ick";
-			};
-
-			venc: encoder@58003000 {
-				compatible = "ti,omap4-venc";
-				reg = <0x58003000 0x1000>;
-				status = "disabled";
-				ti,hwmods = "dss_venc";
-				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
-				clock-names = "fck";
-			};
-
-			dsi1: encoder@58004000 {
-				compatible = "ti,omap4-dsi";
-				reg = <0x58004000 0x200>,
-				      <0x58004200 0x40>,
-				      <0x58004300 0x20>;
-				reg-names = "proto", "phy", "pll";
-				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_dsi1";
-				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
-					 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-			};
-
-			dsi2: encoder@58005000 {
-				compatible = "ti,omap4-dsi";
-				reg = <0x58005000 0x200>,
-				      <0x58005200 0x40>,
-				      <0x58005300 0x20>;
-				reg-names = "proto", "phy", "pll";
-				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_dsi2";
-				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
-					 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-			};
-
-			hdmi: encoder@58006000 {
-				compatible = "ti,omap4-hdmi";
-				reg = <0x58006000 0x200>,
-				      <0x58006200 0x100>,
-				      <0x58006300 0x100>,
-				      <0x58006400 0x1000>;
-				reg-names = "wp", "pll", "phy", "core";
-				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_hdmi";
-				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
-					 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-				dmas = <&sdma 76>;
-				dma-names = "audio_tx";
-			};
-		};
-	};
-};
-
-#include "omap4-l4.dtsi"
-#include "omap4-l4-abe.dtsi"
-#include "omap44xx-clocks.dtsi"
-
-&prm {
-	prm_tesla: prm@400 {
-		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x400 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_core: prm@700 {
-		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x700 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_ivahd: prm@f00 {
-		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
-		reg = <0xf00 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_device: prm@1b00 {
-		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1b00 0x40>;
-		#reset-cells = <1>;
-	};
-};
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
deleted file mode 100644
index 1f6ad1debc90..000000000000
--- a/arch/arm/boot/dts/omap5.dtsi
+++ /dev/null
@@ -1,463 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on "omap4.dtsi"
- */
-
-#include <dt-bindings/bus/ti-sysc.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/omap.h>
-#include <dt-bindings/clock/omap5.h>
-
-/ {
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	compatible = "ti,omap5";
-	interrupt-parent = <&wakeupgen>;
-	chosen { };
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c2;
-		i2c2 = &i2c3;
-		i2c3 = &i2c4;
-		i2c4 = &i2c5;
-		serial0 = &uart1;
-		serial1 = &uart2;
-		serial2 = &uart3;
-		serial3 = &uart4;
-		serial4 = &uart5;
-		serial5 = &uart6;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a15";
-			reg = <0x0>;
-
-			operating-points = <
-				/* kHz    uV */
-				1000000 1060000
-				1500000 1250000
-			>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-
-			/* cooling options */
-			#cooling-cells = <2>; /* min followed by max */
-		};
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a15";
-			reg = <0x1>;
-
-			operating-points = <
-				/* kHz    uV */
-				1000000 1060000
-				1500000 1250000
-			>;
-
-			clocks = <&dpll_mpu_ck>;
-			clock-names = "cpu";
-
-			clock-latency = <300000>; /* From omap-cpufreq driver */
-
-			/* cooling options */
-			#cooling-cells = <2>; /* min followed by max */
-		};
-	};
-
-	thermal-zones {
-		#include "omap4-cpu-thermal.dtsi"
-		#include "omap5-gpu-thermal.dtsi"
-		#include "omap5-core-thermal.dtsi"
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		/* PPI secure/nonsecure IRQ */
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
-		interrupt-parent = <&gic>;
-	};
-
-	pmu {
-		compatible = "arm,cortex-a15-pmu";
-		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
-	gic: interrupt-controller@48211000 {
-		compatible = "arm,cortex-a15-gic";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0 0x48211000 0 0x1000>,
-		      <0 0x48212000 0 0x2000>,
-		      <0 0x48214000 0 0x2000>,
-		      <0 0x48216000 0 0x2000>;
-		interrupt-parent = <&gic>;
-	};
-
-	wakeupgen: interrupt-controller@48281000 {
-		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		reg = <0 0x48281000 0 0x1000>;
-		interrupt-parent = <&gic>;
-	};
-
-	/*
-	 * The soc node represents the soc top level view. It is used for IPs
-	 * that are not memory mapped in the MPU view or for the MPU itself.
-	 */
-	soc {
-		compatible = "ti,omap-infra";
-		mpu {
-			compatible = "ti,omap4-mpu";
-			ti,hwmods = "mpu";
-			sram = <&ocmcram>;
-		};
-	};
-
-	/*
-	 * XXX: Use a flat representation of the OMAP3 interconnect.
-	 * The real OMAP interconnect network is quite complex.
-	 * Since it will not bring real advantage to represent that in DT for
-	 * the moment, just use a fake OCP bus entry to represent the whole bus
-	 * hierarchy.
-	 */
-	ocp {
-		compatible = "ti,omap5-l3-noc", "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0xc0000000>;
-		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
-		reg = <0 0x44000000 0 0x2000>,
-		      <0 0x44800000 0 0x3000>,
-		      <0 0x45000000 0 0x4000>;
-		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-
-		l4_wkup: interconnect@4ae00000 {
-		};
-
-		l4_cfg: interconnect@4a000000 {
-		};
-
-		l4_per: interconnect@48000000 {
-		};
-
-		l4_abe: interconnect@40100000 {
-		};
-
-		ocmcram: sram@40300000 {
-			compatible = "mmio-sram";
-			reg = <0x40300000 0x20000>; /* 128k */
-		};
-
-		gpmc: gpmc@50000000 {
-			compatible = "ti,omap4430-gpmc";
-			reg = <0x50000000 0x1000>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&sdma 4>;
-			dma-names = "rxtx";
-			gpmc,num-cs = <8>;
-			gpmc,num-waitpins = <4>;
-			ti,hwmods = "gpmc";
-			clocks = <&l3_iclk_div>;
-			clock-names = "fck";
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		mmu_dsp: mmu@4a066000 {
-			compatible = "ti,omap4-iommu";
-			reg = <0x4a066000 0x100>;
-			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu_dsp";
-			#iommu-cells = <0>;
-		};
-
-		mmu_ipu: mmu@55082000 {
-			compatible = "ti,omap4-iommu";
-			reg = <0x55082000 0x100>;
-			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-			ti,hwmods = "mmu_ipu";
-			#iommu-cells = <0>;
-			ti,iommu-bus-err-back;
-		};
-
-		dmm@4e000000 {
-			compatible = "ti,omap5-dmm";
-			reg = <0x4e000000 0x800>;
-			interrupts = <0 113 0x4>;
-			ti,hwmods = "dmm";
-		};
-
-		emif1: emif@4c000000 {
-			compatible	= "ti,emif-4d5";
-			ti,hwmods	= "emif1";
-			ti,no-idle-on-init;
-			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
-			reg = <0x4c000000 0x400>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-			hw-caps-read-idle-ctrl;
-			hw-caps-ll-interface;
-			hw-caps-temp-alert;
-		};
-
-		emif2: emif@4d000000 {
-			compatible	= "ti,emif-4d5";
-			ti,hwmods	= "emif2";
-			ti,no-idle-on-init;
-			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
-			reg = <0x4d000000 0x400>;
-			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-			hw-caps-read-idle-ctrl;
-			hw-caps-ll-interface;
-			hw-caps-temp-alert;
-		};
-
-		bandgap: bandgap@4a0021e0 {
-			reg = <0x4a0021e0 0xc
-			       0x4a00232c 0xc
-			       0x4a002380 0x2c
-			       0x4a0023C0 0x3c>;
-			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
-			compatible = "ti,omap5430-bandgap";
-
-			#thermal-sensor-cells = <1>;
-		};
-
-		/* OCP2SCP3 */
-		sata: sata@4a141100 {
-			compatible = "snps,dwc-ahci";
-			reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
-			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&sata_phy>;
-			phy-names = "sata-phy";
-			clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>;
-			ti,hwmods = "sata";
-			ports-implemented = <0x1>;
-		};
-
-		target-module@56000000 {
-			compatible = "ti,sysc-omap4", "ti,sysc";
-			reg = <0x5600fe00 0x4>,
-			      <0x5600fe10 0x4>;
-			reg-names = "rev", "sysc";
-			ti,sysc-midle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
-			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
-			clocks = <&gpu_clkctrl OMAP5_GPU_CLKCTRL 0>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x56000000 0x2000000>;
-
-			/*
-			 * Closed source PowerVR driver, no child device
-			 * binding or driver in mainline
-			 */
-		};
-
-		dss: dss@58000000 {
-			compatible = "ti,omap5-dss";
-			reg = <0x58000000 0x80>;
-			status = "disabled";
-			ti,hwmods = "dss_core";
-			clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
-			clock-names = "fck";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			dispc@58001000 {
-				compatible = "ti,omap5-dispc";
-				reg = <0x58001000 0x1000>;
-				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
-				ti,hwmods = "dss_dispc";
-				clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
-				clock-names = "fck";
-			};
-
-			rfbi: encoder@58002000  {
-				compatible = "ti,omap5-rfbi";
-				reg = <0x58002000 0x100>;
-				status = "disabled";
-				ti,hwmods = "dss_rfbi";
-				clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, <&l3_iclk_div>;
-				clock-names = "fck", "ick";
-			};
-
-			dsi1: encoder@58004000 {
-				compatible = "ti,omap5-dsi";
-				reg = <0x58004000 0x200>,
-				      <0x58004200 0x40>,
-				      <0x58004300 0x40>;
-				reg-names = "proto", "phy", "pll";
-				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_dsi1";
-				clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>,
-					 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-			};
-
-			dsi2: encoder@58005000 {
-				compatible = "ti,omap5-dsi";
-				reg = <0x58009000 0x200>,
-				      <0x58009200 0x40>,
-				      <0x58009300 0x40>;
-				reg-names = "proto", "phy", "pll";
-				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_dsi2";
-				clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>,
-					 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-			};
-
-			hdmi: encoder@58060000 {
-				compatible = "ti,omap5-hdmi";
-				reg = <0x58040000 0x200>,
-				      <0x58040200 0x80>,
-				      <0x58040300 0x80>,
-				      <0x58060000 0x19000>;
-				reg-names = "wp", "pll", "phy", "core";
-				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				status = "disabled";
-				ti,hwmods = "dss_hdmi";
-				clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
-					 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
-				clock-names = "fck", "sys_clk";
-				dmas = <&sdma 76>;
-				dma-names = "audio_tx";
-			};
-		};
-
-		abb_mpu: regulator-abb-mpu {
-			compatible = "ti,abb-v2";
-			regulator-name = "abb_mpu";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			clocks = <&sys_clkin>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			reg = <0x4ae07cdc 0x8>, <0x4ae06014 0x4>,
-			      <0x4a0021c4 0x8>, <0x4ae0c318 0x4>;
-			reg-names = "base-address", "int-address",
-				    "efuse-address", "ldo-address";
-			ti,tranxdone-status-mask = <0x80>;
-			/* LDOVBBMPU_MUX_CTRL */
-			ti,ldovbb-override-mask = <0x400>;
-			/* LDOVBBMPU_VSET_OUT */
-			ti,ldovbb-vset-mask = <0x1F>;
-
-			/*
-			 * NOTE: only FBB mode used but actual vset will
-			 * determine final biasing
-			 */
-			ti,abb_info = <
-			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
-			1060000		0	0x0	0 0x02000000 0x01F00000
-			1250000		0	0x4	0 0x02000000 0x01F00000
-			>;
-		};
-
-		abb_mm: regulator-abb-mm {
-			compatible = "ti,abb-v2";
-			regulator-name = "abb_mm";
-			#address-cells = <0>;
-			#size-cells = <0>;
-			clocks = <&sys_clkin>;
-			ti,settling-time = <50>;
-			ti,clock-cycles = <16>;
-
-			reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
-			      <0x4a0021a4 0x8>, <0x4ae0c314 0x4>;
-			reg-names = "base-address", "int-address",
-				    "efuse-address", "ldo-address";
-			ti,tranxdone-status-mask = <0x80000000>;
-			/* LDOVBBMM_MUX_CTRL */
-			ti,ldovbb-override-mask = <0x400>;
-			/* LDOVBBMM_VSET_OUT */
-			ti,ldovbb-vset-mask = <0x1F>;
-
-			/*
-			 * NOTE: only FBB mode used but actual vset will
-			 * determine final biasing
-			 */
-			ti,abb_info = <
-			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
-			1025000		0	0x0	0 0x02000000 0x01F00000
-			1120000		0	0x4	0 0x02000000 0x01F00000
-			>;
-		};
-	};
-};
-
-&cpu_thermal {
-	polling-delay = <500>; /* milliseconds */
-	coefficients = <65 (-1791)>;
-};
-
-#include "omap5-l4.dtsi"
-#include "omap54xx-clocks.dtsi"
-
-&gpu_thermal {
-	coefficients = <117 (-2992)>;
-};
-
-&core_thermal {
-	coefficients = <0 2000>;
-};
-
-#include "omap5-l4-abe.dtsi"
-#include "omap54xx-clocks.dtsi"
-
-&prm {
-	prm_dsp: prm@400 {
-		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
-		reg = <0x400 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_core: prm@700 {
-		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
-		reg = <0x700 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_iva: prm@1200 {
-		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1200 0x100>;
-		#reset-cells = <1>;
-	};
-
-	prm_device: prm@1c00 {
-		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
-		reg = <0x1c00 0x100>;
-		#reset-cells = <1>;
-	};
-};
diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi
deleted file mode 100644
index 5ceb6cc4451d..000000000000
--- a/arch/arm/boot/dts/owl-s500.dtsi
+++ /dev/null
@@ -1,188 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Actions Semi S500 SoC
- *
- * Copyright (c) 2016-2017 Andreas Färber
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/power/owl-s500-powergate.h>
-
-/ {
-	compatible = "actions,s500";
-	interrupt-parent = <&gic>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	aliases {
-	};
-
-	chosen {
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0x0>;
-			enable-method = "actions,s500-smp";
-		};
-
-		cpu1: cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0x1>;
-			enable-method = "actions,s500-smp";
-		};
-
-		cpu2: cpu@2 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0x2>;
-			enable-method = "actions,s500-smp";
-			power-domains = <&sps S500_PD_CPU2>;
-		};
-
-		cpu3: cpu@3 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0x3>;
-			enable-method = "actions,s500-smp";
-			power-domains = <&sps S500_PD_CPU3>;
-		};
-	};
-
-	arm-pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-		             <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-		             <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-		             <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
-	};
-
-	hosc: hosc {
-		compatible = "fixed-clock";
-		clock-frequency = <24000000>;
-		#clock-cells = <0>;
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		scu: scu@b0020000 {
-			compatible = "arm,cortex-a9-scu";
-			reg = <0xb0020000 0x100>;
-		};
-
-		global_timer: timer@b0020200 {
-			compatible = "arm,cortex-a9-global-timer";
-			reg = <0xb0020200 0x100>;
-			interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
-			status = "disabled";
-		};
-
-		twd_timer: timer@b0020600 {
-			compatible = "arm,cortex-a9-twd-timer";
-			reg = <0xb0020600 0x20>;
-			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
-			status = "disabled";
-		};
-
-		twd_wdt: wdt@b0020620 {
-			compatible = "arm,cortex-a9-twd-wdt";
-			reg = <0xb0020620 0xe0>;
-			interrupts = <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
-			status = "disabled";
-		};
-
-		gic: interrupt-controller@b0021000 {
-			compatible = "arm,cortex-a9-gic";
-			reg = <0xb0021000 0x1000>,
-			      <0xb0020100 0x0100>;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-		};
-
-		l2: cache-controller@b0022000 {
-			compatible = "arm,pl310-cache";
-			reg = <0xb0022000 0x1000>;
-			cache-unified;
-			cache-level = <2>;
-			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
-			arm,tag-latency = <3 3 2>;
-			arm,data-latency = <5 3 3>;
-		};
-
-		uart0: serial@b0120000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb0120000 0x2000>;
-			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		uart1: serial@b0122000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb0122000 0x2000>;
-			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		uart2: serial@b0124000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb0124000 0x2000>;
-			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		uart3: serial@b0126000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb0126000 0x2000>;
-			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		uart4: serial@b0128000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb0128000 0x2000>;
-			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		uart5: serial@b012a000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb012a000 0x2000>;
-			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		uart6: serial@b012c000 {
-			compatible = "actions,s500-uart", "actions,owl-uart";
-			reg = <0xb012c000 0x2000>;
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		timer: timer@b0168000 {
-			compatible = "actions,s500-timer";
-			reg = <0xb0168000 0x8000>;
-			interrupts = <GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
-			             <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
-			             <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-			             <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "2hz0", "2hz1", "timer0", "timer1";
-		};
-
-		sps: power-controller@b01b0100 {
-			compatible = "actions,s500-sps";
-			reg = <0xb01b0100 0x100>;
-			#power-domain-cells = <1>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ox810se-wd-mbwe.dts b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
deleted file mode 100644
index 7e2fcb220aea..000000000000
--- a/arch/arm/boot/dts/ox810se-wd-mbwe.dts
+++ /dev/null
@@ -1,111 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * wd-mbwe.dtsi - Device tree file for Western Digital My Book World Edition
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-/dts-v1/;
-#include "ox810se.dtsi"
-
-/ {
-	model = "Western Digital My Book World Edition";
-
-	compatible = "wd,mbwe", "oxsemi,ox810se";
-
-	chosen {
-		bootargs = "console=ttyS1,115200n8 earlyprintk=serial";
-	};
-
-	memory {
-		/* 128Mbytes DDR */
-		reg = <0x48000000 0x8000000>;
-	};
-
-	aliases {
-		serial1 = &uart1;
-		gpio0 = &gpio0;
-		gpio1 = &gpio1;
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		poll-interval = <100>;
-
-		power {
-			label = "power";
-			gpios = <&gpio0 0 1>;
-			linux,code = <0x198>;
-		};
-
-		recovery {
-			label = "recovery";
-			gpios = <&gpio0 4 1>;
-			linux,code = <0xab>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		a0 {
-			label = "activity0";
-			gpios = <&gpio0 25 0>;
-			default-state = "keep";
-		};
-
-		a1 {
-			label = "activity1";
-			gpios = <&gpio0 26 0>;
-			default-state = "keep";
-		};
-
-		a2 {
-			label = "activity2";
-			gpios = <&gpio0 5 0>;
-			default-state = "keep";
-		};
-
-		a3 {
-			label = "activity3";
-			gpios = <&gpio0 6 0>;
-			default-state = "keep";
-		};
-
-		a4 {
-			label = "activity4";
-			gpios = <&gpio0 7 0>;
-			default-state = "keep";
-		};
-
-		a5 {
-			label = "activity5";
-			gpios = <&gpio1 2 0>;
-			default-state = "keep";
-		};
-	};
-
-	i2c-gpio {
-		compatible = "i2c-gpio";
-		gpios = <&gpio0 3 0 /* sda */
-			 &gpio0 2 0 /* scl */
-			 >;
-		i2c-gpio,delay-us = <2>;        /* ~100 kHz */
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		rtc0: rtc@48 {
-			compatible = "st,m41t00";
-			reg = <0x68>;
-		};
-	};
-};
-
-&uart1 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-};
diff --git a/arch/arm/boot/dts/ox810se.dtsi b/arch/arm/boot/dts/ox810se.dtsi
deleted file mode 100644
index 9f6c2b660ed3..000000000000
--- a/arch/arm/boot/dts/ox810se.dtsi
+++ /dev/null
@@ -1,339 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * ox810se.dtsi - Device tree file for Oxford Semiconductor OX810SE SoC
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-#include <dt-bindings/clock/oxsemi,ox810se.h>
-#include <dt-bindings/reset/oxsemi,ox810se.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	compatible = "oxsemi,ox810se";
-
-	cpus {
-		#address-cells = <0>;
-		#size-cells = <0>;
-
-		cpu {
-			device_type = "cpu";
-			compatible = "arm,arm926ej-s";
-			clocks = <&armclk>;
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		/* Max 256MB @ 0x48000000 */
-		reg = <0x48000000 0x10000000>;
-	};
-
-	clocks {
-		osc: oscillator {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <25000000>;
-		};
-
-		gmacclk: gmacclk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <125000000>;
-		};
-
-		rpsclk: rpsclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <1>;
-			clock-mult = <1>;
-			clocks = <&osc>;
-		};
-
-		pll400: pll400 {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <733333333>;
-		};
-
-		sysclk: sysclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <4>;
-			clock-mult = <1>;
-			clocks = <&pll400>;
-		};
-
-		armclk: armclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <2>;
-			clock-mult = <1>;
-			clocks = <&pll400>;
-		};
-	};
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges;
-		interrupt-parent = <&intc>;
-
-		apb-bridge@44000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x44000000 0x1000000>;
-
-			pinctrl: pinctrl {
-				compatible = "oxsemi,ox810se-pinctrl";
-
-				/* Regmap for sys registers */
-				oxsemi,sys-ctrl = <&sys>;
-
-				pinctrl_uart0: uart0 {
-					uart0a {
-						pins = "gpio31";
-						function = "fct3";
-					};
-					uart0b {
-						pins = "gpio32";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart0_modem: uart0_modem {
-					uart0c {
-						pins = "gpio27";
-						function = "fct3";
-					};
-					uart0d {
-						pins = "gpio28";
-						function = "fct3";
-					};
-					uart0e {
-						pins = "gpio29";
-						function = "fct3";
-					};
-					uart0f {
-						pins = "gpio30";
-						function = "fct3";
-					};
-					uart0g {
-						pins = "gpio33";
-						function = "fct3";
-					};
-					uart0h {
-						pins = "gpio34";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart1: uart1 {
-					uart1a {
-						pins = "gpio20";
-						function = "fct3";
-					};
-					uart1b {
-						pins = "gpio22";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart1_modem: uart1_modem {
-					uart1c {
-						pins = "gpio8";
-						function = "fct3";
-					};
-					uart1d {
-						pins = "gpio9";
-						function = "fct3";
-					};
-					uart1e {
-						pins = "gpio23";
-						function = "fct3";
-					};
-					uart1f {
-						pins = "gpio24";
-						function = "fct3";
-					};
-					uart1g {
-						pins = "gpio25";
-						function = "fct3";
-					};
-					uart1h {
-						pins = "gpio26";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart2: uart2 {
-					uart2a {
-						pins = "gpio6";
-						function = "fct3";
-					};
-					uart2b {
-						pins = "gpio7";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart2_modem: uart2_modem {
-					uart2c {
-						pins = "gpio0";
-						function = "fct3";
-					};
-					uart2d {
-						pins = "gpio1";
-						function = "fct3";
-					};
-					uart2e {
-						pins = "gpio2";
-						function = "fct3";
-					};
-					uart2f {
-						pins = "gpio3";
-						function = "fct3";
-					};
-					uart2g {
-						pins = "gpio4";
-						function = "fct3";
-					};
-					uart2h {
-						pins = "gpio5";
-						function = "fct3";
-					};
-				};
-			};
-
-			gpio0: gpio@0 {
-				compatible = "oxsemi,ox810se-gpio";
-				reg = <0x000000 0x100000>;
-				interrupts = <21>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <32>;
-				oxsemi,gpio-bank = <0>;
-				gpio-ranges = <&pinctrl 0 0 32>;
-			};
-
-			gpio1: gpio@100000 {
-				compatible = "oxsemi,ox810se-gpio";
-				reg = <0x100000 0x100000>;
-				interrupts = <22>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <3>;
-				oxsemi,gpio-bank = <1>;
-				gpio-ranges = <&pinctrl 0 32 3>;
-			};
-
-			uart0: serial@200000 {
-			       compatible = "ns16550a";
-			       reg = <0x200000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <23>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART1>;
-			};
-
-			uart1: serial@300000 {
-			       compatible = "ns16550a";
-			       reg = <0x300000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <24>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART2>;
-			};
-
-			uart2: serial@900000 {
-			       compatible = "ns16550a";
-			       reg = <0x900000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <29>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART3>;
-			};
-
-			uart3: serial@a00000 {
-			       compatible = "ns16550a";
-			       reg = <0xa00000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <30>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART4>;
-			};
-		};
-
-		apb-bridge@45000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x45000000 0x1000000>;
-
-			sys: sys-ctrl@0 {
-				compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd";
-				reg = <0x000000 0x100000>;
-
-				reset: reset-controller {
-					compatible = "oxsemi,ox810se-reset";
-					#reset-cells = <1>;
-				};
-
-				stdclk: stdclk {
-					compatible = "oxsemi,ox810se-stdclk";
-					#clock-cells = <1>;
-				};
-			};
-
-			rps@300000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "simple-bus";
-				ranges = <0 0x300000 0x100000>;
-
-				intc: interrupt-controller@0 {
-					compatible = "oxsemi,ox810se-rps-irq";
-					interrupt-controller;
-					reg = <0 0x200>;
-					#interrupt-cells = <1>;
-					valid-mask = <0xFFFFFFFF>;
-					clear-mask = <0>;
-				};
-
-				timer0: timer@200 {
-					compatible = "oxsemi,ox810se-rps-timer";
-					reg = <0x200 0x40>;
-					clocks = <&rpsclk>;
-					interrupts = <4 5>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts b/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
deleted file mode 100644
index c3daceccde55..000000000000
--- a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * cloudengines-pogoplug-series-3.dtsi - Device tree file for Cloud Engines PogoPlug Series 3
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-/dts-v1/;
-#include "ox820.dtsi"
-
-/ {
-	model = "Cloud Engines PogoPlug Series 3";
-
-	compatible = "cloudengines,pogoplugv3", "oxsemi,ox820";
-
-	chosen {
-		bootargs = "earlyprintk";
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory {
-		/* 128Mbytes DDR */
-		reg = <0x60000000 0x8000000>;
-	};
-
-	aliases {
-		serial0 = &uart0;
-		gpio0 = &gpio0;
-		gpio1 = &gpio1;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		blue {
-			label = "pogoplug:blue";
-			gpios = <&gpio0 2 0>;
-			default-state = "keep";
-		};
-
-		orange {
-			label = "pogoplug:orange";
-			gpios = <&gpio1 16 1>;
-			default-state = "keep";
-		};
-
-		green {
-			label = "pogoplug:green";
-			gpios = <&gpio1 17 1>;
-			default-state = "keep";
-		};
-	};
-};
-
-&uart0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart0>;
-};
-
-&nandc {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nand>;
-
-	nand@0 {
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		nand-ecc-mode = "soft";
-		nand-ecc-algo = "hamming";
-
-		partition@0 {
-			label = "boot";
-			reg = <0x00000000 0x00e00000>;
-			read-only;
-		};
-
-		partition@e00000 {
-			label = "ubi";
-			reg = <0x00e00000 0x07200000>;
-		};
-	};
-};
-
-&etha {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_etha_mdio>;
-};
diff --git a/arch/arm/boot/dts/ox820.dtsi b/arch/arm/boot/dts/ox820.dtsi
deleted file mode 100644
index c9b327732063..000000000000
--- a/arch/arm/boot/dts/ox820.dtsi
+++ /dev/null
@@ -1,299 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * ox820.dtsi - Device tree file for Oxford Semiconductor OX820 SoC
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/oxsemi,ox820.h>
-#include <dt-bindings/reset/oxsemi,ox820.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	compatible = "oxsemi,ox820";
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		enable-method = "oxsemi,ox820-smp";
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,arm11mpcore";
-			clocks = <&armclk>;
-			reg = <0>;
-		};
-
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,arm11mpcore";
-			clocks = <&armclk>;
-			reg = <1>;
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		/* Max 512MB @ 0x60000000 */
-		reg = <0x60000000 0x20000000>;
-	};
-
-	clocks {
-		osc: oscillator {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <25000000>;
-		};
-
-		gmacclk: gmacclk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <125000000>;
-		};
-
-		sysclk: sysclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <4>;
-			clock-mult = <1>;
-			clocks = <&osc>;
-		};
-
-		plla: plla {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <850000000>;
-		};
-
-		armclk: armclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <2>;
-			clock-mult = <1>;
-			clocks = <&plla>;
-		};
-	};
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges;
-		interrupt-parent = <&gic>;
-
-		nandc: nand-controller@41000000 {
-			compatible = "oxsemi,ox820-nand";
-			reg = <0x41000000 0x100000>;
-			clocks = <&stdclk CLK_820_NAND>;
-			resets = <&reset RESET_NAND>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		etha: ethernet@40400000 {
-			compatible = "oxsemi,ox820-dwmac", "snps,dwmac";
-			reg = <0x40400000 0x2000>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "macirq", "eth_wake_irq";
-			mac-address = [000000000000]; /* Filled in by U-Boot */
-			phy-mode = "rgmii";
-
-			clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>;
-			clock-names = "gmac", "stmmaceth";
-			resets = <&reset RESET_MAC>;
-
-			/* Regmap for sys registers */
-			oxsemi,sys-ctrl = <&sys>;
-
-			status = "disabled";
-		};
-
-		apb-bridge@44000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x44000000 0x1000000>;
-
-			pinctrl: pinctrl {
-				compatible = "oxsemi,ox820-pinctrl";
-
-				/* Regmap for sys registers */
-				oxsemi,sys-ctrl = <&sys>;
-
-				pinctrl_uart0: uart0 {
-					uart0 {
-						pins = "gpio30", "gpio31";
-						function = "fct5";
-					};
-				};
-
-				pinctrl_uart0_modem: uart0_modem {
-					uart0_modem_a {
-						pins = "gpio24", "gpio24", "gpio26", "gpio27";
-						function = "fct4";
-					};
-					uart0_modem_b {
-						pins = "gpio28", "gpio29";
-						function = "fct5";
-					};
-				};
-
-				pinctrl_uart1: uart1 {
-					uart1 {
-						pins = "gpio7", "gpio8";
-						function = "fct4";
-					};
-				};
-
-				pinctrl_uart1_modem: uart1_modem {
-					uart1_modem {
-						pins = "gpio5", "gpio6", "gpio40", "gpio41", "gpio42", "gpio43";
-						function = "fct4";
-					};
-				};
-
-				pinctrl_etha_mdio: etha_mdio {
-					etha_mdio {
-						pins = "gpio3", "gpio4";
-						function = "fct1";
-					};
-				};
-
-				pinctrl_nand: nand {
-					nand {
-						pins = "gpio12", "gpio13", "gpio14", "gpio15",
-						     "gpio16", "gpio17", "gpio18", "gpio19",
-						     "gpio20", "gpio21", "gpio22", "gpio23",
-						     "gpio24";
-						function = "fct1";
-					};
-				};
-			};
-
-			gpio0: gpio@0 {
-				compatible = "oxsemi,ox820-gpio";
-				reg = <0x000000 0x100000>;
-				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <32>;
-				oxsemi,gpio-bank = <0>;
-				gpio-ranges = <&pinctrl 0 0 32>;
-			};
-
-			gpio1: gpio@100000 {
-				compatible = "oxsemi,ox820-gpio";
-				reg = <0x100000 0x100000>;
-				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <18>;
-				oxsemi,gpio-bank = <1>;
-				gpio-ranges = <&pinctrl 0 32 18>;
-			};
-
-			uart0: serial@200000 {
-			       compatible = "ns16550a";
-			       reg = <0x200000 0x100000>;
-			       interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       clocks = <&sysclk>;
-			       resets = <&reset RESET_UART1>;
-			};
-
-			uart1: serial@300000 {
-			       compatible = "ns16550a";
-			       reg = <0x200000 0x100000>;
-			       interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       clocks = <&sysclk>;
-			       resets = <&reset RESET_UART2>;
-			};
-
-			rps@400000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "simple-bus";
-				ranges = <0 0x400000 0x100000>;
-
-				intc: interrupt-controller@0 {
-					compatible = "oxsemi,ox820-rps-irq", "oxsemi,ox810se-rps-irq";
-					interrupt-controller;
-					reg = <0 0x200>;
-					interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
-					#interrupt-cells = <1>;
-					valid-mask = <0xFFFFFFFF>;
-					clear-mask = <0>;
-				};
-
-				timer0: timer@200 {
-					compatible = "oxsemi,ox820-rps-timer";
-					reg = <0x200 0x40>;
-					clocks = <&sysclk>;
-					interrupt-parent = <&intc>;
-					interrupts = <4>;
-				};
-			};
-
-			sys: sys-ctrl@e00000 {
-				compatible = "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd";
-				reg = <0xe00000 0x200000>;
-
-				reset: reset-controller {
-					compatible = "oxsemi,ox820-reset", "oxsemi,ox810se-reset";
-					#reset-cells = <1>;
-				};
-
-				stdclk: stdclk {
-					compatible = "oxsemi,ox820-stdclk", "oxsemi,ox810se-stdclk";
-					#clock-cells = <1>;
-				};
-			};
-		};
-
-		apb-bridge@47000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x47000000 0x1000000>;
-
-			scu: scu@0 {
-				compatible = "arm,arm11mp-scu";
-				reg = <0x0 0x100>;
-			};
-
-			local-timer@600 {
-				compatible = "arm,arm11mp-twd-timer";
-				reg = <0x600 0x20>;
-				interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3)|IRQ_TYPE_LEVEL_HIGH)>;
-				clocks = <&armclk>;
-			};
-
-			gic: gic@1000 {
-				compatible = "arm,arm11mp-gic";
-				interrupt-controller;
-				#interrupt-cells = <3>;
-				reg = <0x1000 0x1000>,
-				      <0x100 0x500>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/picoxcell-pc3x2.dtsi b/arch/arm/boot/dts/picoxcell-pc3x2.dtsi
deleted file mode 100644
index 5ae860788339..000000000000
--- a/arch/arm/boot/dts/picoxcell-pc3x2.dtsi
+++ /dev/null
@@ -1,240 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2011 Picochip, Jamie Iles
- */
-/ {
-	model = "Picochip picoXcell PC3X2";
-	compatible = "picochip,pc3x2";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <0>;
-		#size-cells = <0>;
-
-		cpu {
-			compatible = "arm,arm1176jz-s";
-			device_type = "cpu";
-			clock-frequency = <400000000>;
-			d-cache-line-size = <32>;
-			d-cache-size = <32768>;
-			i-cache-line-size = <32>;
-			i-cache-size = <32768>;
-		};
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		pclk: clock@0 {
-			compatible = "fixed-clock";
-			clock-outputs = "bus", "pclk";
-			clock-frequency = <200000000>;
-			ref-clock = <&ref_clk>, "ref";
-		};
-	};
-
-	paxi {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0x80000000 0x400000>;
-
-		emac: gem@30000 {
-			compatible = "cadence,gem";
-			reg = <0x30000 0x10000>;
-			interrupts = <31>;
-		};
-
-		dmac1: dmac@40000 {
-			compatible = "snps,dw-dmac";
-			reg = <0x40000 0x10000>;
-			interrupts = <25>;
-		};
-
-		dmac2: dmac@50000 {
-			compatible = "snps,dw-dmac";
-			reg = <0x50000 0x10000>;
-			interrupts = <26>;
-		};
-
-		vic0: interrupt-controller@60000 {
-			compatible = "arm,pl192-vic";
-			interrupt-controller;
-			reg = <0x60000 0x1000>;
-			#interrupt-cells = <1>;
-		};
-
-		vic1: interrupt-controller@64000 {
-			compatible = "arm,pl192-vic";
-			interrupt-controller;
-			reg = <0x64000 0x1000>;
-			#interrupt-cells = <1>;
-		};
-
-		fuse: picoxcell-fuse@80000 {
-			compatible = "picoxcell,fuse-pc3x2";
-			reg = <0x80000 0x10000>;
-		};
-
-		ssi: picoxcell-spi@90000 {
-			compatible = "picoxcell,spi";
-			reg = <0x90000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <10>;
-		};
-
-		ipsec: spacc@100000 {
-			compatible = "picochip,spacc-ipsec";
-			reg = <0x100000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <24>;
-			ref-clock = <&pclk>, "ref";
-		};
-
-		srtp: spacc@140000 {
-			compatible = "picochip,spacc-srtp";
-			reg = <0x140000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <23>;
-		};
-
-		l2_engine: spacc@180000 {
-			compatible = "picochip,spacc-l2";
-			reg = <0x180000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <22>;
-			ref-clock = <&pclk>, "ref";
-		};
-
-		apb {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x200000 0x80000>;
-
-			rtc0: rtc@0 {
-				compatible = "picochip,pc3x2-rtc";
-				clock-freq = <200000000>;
-				reg = <0x00000 0xf>;
-				interrupt-parent = <&vic1>;
-				interrupts = <8>;
-			};
-
-			timer0: timer@10000 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <4>;
-				clock-freq = <200000000>;
-				reg = <0x10000 0x14>;
-			};
-
-			timer1: timer@10014 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <5>;
-				clock-freq = <200000000>;
-				reg = <0x10014 0x14>;
-			};
-
-			timer2: timer@10028 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <6>;
-				clock-freq = <200000000>;
-				reg = <0x10028 0x14>;
-			};
-
-			timer3: timer@1003c {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <7>;
-				clock-freq = <200000000>;
-				reg = <0x1003c 0x14>;
-			};
-
-			gpio: gpio@20000 {
-				compatible = "snps,dw-apb-gpio";
-				reg = <0x20000 0x1000>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg-io-width = <4>;
-
-				banka: gpio-controller@0 {
-					compatible = "snps,dw-apb-gpio-bank";
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-generic,nr-gpio = <8>;
-
-					regoffset-dat = <0x50>;
-					regoffset-set = <0x00>;
-					regoffset-dirout = <0x04>;
-				};
-
-				bankb: gpio-controller@1 {
-					compatible = "snps,dw-apb-gpio-bank";
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-generic,nr-gpio = <8>;
-
-					regoffset-dat = <0x54>;
-					regoffset-set = <0x0c>;
-					regoffset-dirout = <0x10>;
-				};
-			};
-
-			uart0: uart@30000 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x30000 0x1000>;
-				interrupt-parent = <&vic1>;
-				interrupts = <10>;
-				clock-frequency = <3686400>;
-				reg-shift = <2>;
-				reg-io-width = <4>;
-			};
-
-			uart1: uart@40000 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x40000 0x1000>;
-				interrupt-parent = <&vic1>;
-				interrupts = <9>;
-				clock-frequency = <3686400>;
-				reg-shift = <2>;
-				reg-io-width = <4>;
-			};
-
-			wdog: watchdog@50000 {
-				compatible = "snps,dw-apb-wdg";
-				reg = <0x50000 0x10000>;
-				interrupt-parent = <&vic0>;
-				interrupts = <11>;
-				bus-clock = <&pclk>, "bus";
-			};
-		};
-	};
-
-	rwid-axi {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges;
-
-		ebi@50000000 {
-			compatible = "simple-bus";
-			#address-cells = <2>;
-			#size-cells = <1>;
-			ranges = <0 0 0x40000000 0x08000000
-				  1 0 0x48000000 0x08000000
-				  2 0 0x50000000 0x08000000
-				  3 0 0x58000000 0x08000000>;
-		};
-
-		axi2pico@c0000000 {
-			compatible = "picochip,axi2pico-pc3x2";
-			reg = <0xc0000000 0x10000>;
-			interrupts = <13 14 15 16 17 18 19 20 21>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/picoxcell-pc3x3.dtsi b/arch/arm/boot/dts/picoxcell-pc3x3.dtsi
deleted file mode 100644
index fa93155fadb7..000000000000
--- a/arch/arm/boot/dts/picoxcell-pc3x3.dtsi
+++ /dev/null
@@ -1,356 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2011 Picochip, Jamie Iles
- */
-/ {
-	model = "Picochip picoXcell PC3X3";
-	compatible = "picochip,pc3x3";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <0>;
-		#size-cells = <0>;
-
-		cpu {
-			compatible = "arm,arm1176jz-s";
-			device_type = "cpu";
-			cpu-clock = <&arm_clk>, "cpu";
-			d-cache-line-size = <32>;
-			d-cache-size = <32768>;
-			i-cache-line-size = <32>;
-			i-cache-size = <32768>;
-		};
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		clkgate: clkgate@800a0048 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x800a0048 4>;
-			compatible = "picochip,pc3x3-clk-gate";
-
-			tzprot_clk: clock@0 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <0>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			spi_clk: clock@1 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <1>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			dmac0_clk: clock@2 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <2>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			dmac1_clk: clock@3 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <3>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			ebi_clk: clock@4 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <4>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			ipsec_clk: clock@5 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <5>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			l2_clk: clock@6 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <6>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			trng_clk: clock@7 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <7>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			fuse_clk: clock@8 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <8>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-
-			otp_clk: clock@9 {
-				compatible = "picochip,pc3x3-gated-clk";
-				clock-outputs = "bus";
-				picochip,clk-disable-bit = <9>;
-				clock-frequency = <200000000>;
-				ref-clock = <&ref_clk>, "ref";
-			};
-		};
-
-		arm_clk: clock@11 {
-			compatible = "picochip,pc3x3-pll";
-			reg = <0x800a0050 0x8>;
-			picochip,min-freq = <140000000>;
-			picochip,max-freq = <700000000>;
-			ref-clock = <&ref_clk>, "ref";
-			clock-outputs = "cpu";
-		};
-
-		pclk: clock@12 {
-			compatible = "fixed-clock";
-			clock-outputs = "bus", "pclk";
-			clock-frequency = <200000000>;
-			ref-clock = <&ref_clk>, "ref";
-		};
-	};
-
-	paxi {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0x80000000 0x400000>;
-
-		emac: gem@30000 {
-			compatible = "cadence,gem";
-			reg = <0x30000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <31>;
-		};
-
-		dmac1: dmac@40000 {
-			compatible = "snps,dw-dmac";
-			reg = <0x40000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <25>;
-		};
-
-		dmac2: dmac@50000 {
-			compatible = "snps,dw-dmac";
-			reg = <0x50000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <26>;
-		};
-
-		vic0: interrupt-controller@60000 {
-			compatible = "arm,pl192-vic";
-			interrupt-controller;
-			reg = <0x60000 0x1000>;
-			#interrupt-cells = <1>;
-		};
-
-		vic1: interrupt-controller@64000 {
-			compatible = "arm,pl192-vic";
-			interrupt-controller;
-			reg = <0x64000 0x1000>;
-			#interrupt-cells = <1>;
-		};
-
-		fuse: picoxcell-fuse@80000 {
-			compatible = "picoxcell,fuse-pc3x3";
-			reg = <0x80000 0x10000>;
-		};
-
-		ssi: picoxcell-spi@90000 {
-			compatible = "picoxcell,spi";
-			reg = <0x90000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <10>;
-		};
-
-		ipsec: spacc@100000 {
-			compatible = "picochip,spacc-ipsec";
-			reg = <0x100000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <24>;
-			ref-clock = <&ipsec_clk>, "ref";
-		};
-
-		srtp: spacc@140000 {
-			compatible = "picochip,spacc-srtp";
-			reg = <0x140000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <23>;
-		};
-
-		l2_engine: spacc@180000 {
-			compatible = "picochip,spacc-l2";
-			reg = <0x180000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <22>;
-			ref-clock = <&l2_clk>, "ref";
-		};
-
-		apb {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x200000 0x80000>;
-
-			rtc0: rtc@0 {
-				compatible = "picochip,pc3x2-rtc";
-				clock-freq = <200000000>;
-				reg = <0x00000 0xf>;
-				interrupt-parent = <&vic0>;
-				interrupts = <8>;
-			};
-
-			timer0: timer@10000 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <4>;
-				clock-freq = <200000000>;
-				reg = <0x10000 0x14>;
-			};
-
-			timer1: timer@10014 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <5>;
-				clock-freq = <200000000>;
-				reg = <0x10014 0x14>;
-			};
-
-			gpio: gpio@20000 {
-				compatible = "snps,dw-apb-gpio";
-				reg = <0x20000 0x1000>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg-io-width = <4>;
-
-				banka: gpio-controller@0 {
-					compatible = "snps,dw-apb-gpio-bank";
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-generic,nr-gpio = <8>;
-
-					regoffset-dat = <0x50>;
-					regoffset-set = <0x00>;
-					regoffset-dirout = <0x04>;
-				};
-
-				bankb: gpio-controller@1 {
-					compatible = "snps,dw-apb-gpio-bank";
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-generic,nr-gpio = <16>;
-
-					regoffset-dat = <0x54>;
-					regoffset-set = <0x0c>;
-					regoffset-dirout = <0x10>;
-				};
-
-				bankd: gpio-controller@2 {
-					compatible = "snps,dw-apb-gpio-bank";
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-generic,nr-gpio = <30>;
-
-					regoffset-dat = <0x5c>;
-					regoffset-set = <0x24>;
-					regoffset-dirout = <0x28>;
-				};
-			};
-
-			uart0: uart@30000 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x30000 0x1000>;
-				interrupt-parent = <&vic1>;
-				interrupts = <10>;
-				clock-frequency = <3686400>;
-				reg-shift = <2>;
-				reg-io-width = <4>;
-			};
-
-			uart1: uart@40000 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x40000 0x1000>;
-				interrupt-parent = <&vic1>;
-				interrupts = <9>;
-				clock-frequency = <3686400>;
-				reg-shift = <2>;
-				reg-io-width = <4>;
-			};
-
-			wdog: watchdog@50000 {
-				compatible = "snps,dw-apb-wdg";
-				reg = <0x50000 0x10000>;
-				interrupt-parent = <&vic0>;
-				interrupts = <11>;
-				bus-clock = <&pclk>, "bus";
-			};
-
-			timer2: timer@60000 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <6>;
-				clock-freq = <200000000>;
-				reg = <0x60000 0x14>;
-			};
-
-			timer3: timer@60014 {
-				compatible = "picochip,pc3x2-timer";
-				interrupt-parent = <&vic0>;
-				interrupts = <7>;
-				clock-freq = <200000000>;
-				reg = <0x60014 0x14>;
-			};
-		};
-	};
-
-	rwid-axi {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges;
-
-		ebi@50000000 {
-			compatible = "simple-bus";
-			#address-cells = <2>;
-			#size-cells = <1>;
-			ranges = <0 0 0x40000000 0x08000000
-				  1 0 0x48000000 0x08000000
-				  2 0 0x50000000 0x08000000
-				  3 0 0x58000000 0x08000000>;
-		};
-
-		axi2pico@c0000000 {
-			compatible = "picochip,axi2pico-pc3x3";
-			reg = <0xc0000000 0x10000>;
-			interrupt-parent = <&vic0>;
-			interrupts = <13 14 15 16 17 18 19 20 21>;
-		};
-
-		otp@ffff8000 {
-			compatible = "picochip,otp-pc3x3";
-			reg = <0xffff8000 0x8000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/picoxcell-pc7302-pc3x2.dts b/arch/arm/boot/dts/picoxcell-pc7302-pc3x2.dts
deleted file mode 100644
index 3626e5380681..000000000000
--- a/arch/arm/boot/dts/picoxcell-pc7302-pc3x2.dts
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2011 Picochip, Jamie Iles
- */
-
-/dts-v1/;
-/include/ "picoxcell-pc3x2.dtsi"
-/ {
-	model = "Picochip PC7302 (PC3X2)";
-	compatible = "picochip,pc7302-pc3x2", "picochip,pc3x2";
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x08000000>;
-	};
-
-	chosen {
-		stdout-path = &uart0;
-	};
-
-	clocks {
-		ref_clk: clock@1 {
-			compatible = "fixed-clock";
-			clock-outputs = "ref";
-			clock-frequency = <20000000>;
-		};
-	};
-
-	rwid-axi {
-		ebi@50000000 {
-			nand: gpio-nand@2,0 {
-				compatible = "gpio-control-nand";
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <2 0x0000 0x1000>;
-				bus-clock = <&pclk>, "bus";
-				gpio-control-nand,io-sync-reg =
-					<0x00000000 0x80220000>;
-
-				gpios = <&banka 1 0	/* rdy */
-					 &banka 2 0 	/* nce */
-					 &banka 3 0 	/* ale */
-					 &banka 4 0 	/* cle */
-					 0		/* nwp */>;
-
-				boot@100000 {
-					label = "Boot";
-					reg = <0x100000 0x80000>;
-				};
-
-				redundant-boot@200000 {
-					label = "Redundant Boot";
-					reg = <0x200000 0x80000>;
-				};
-
-				boot-env@300000 {
-					label = "Boot Evironment";
-					reg = <0x300000 0x20000>;
-				};
-
-				redundant-boot-env@320000 {
-					label = "Redundant Boot Environment";
-					reg = <0x300000 0x20000>;
-				};
-
-				kernel@380000 {
-					label = "Kernel";
-					reg = <0x380000 0x800000>;
-				};
-
-				fs@b80000 {
-					label = "File System";
-					reg = <0xb80000 0xf480000>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/picoxcell-pc7302-pc3x3.dts b/arch/arm/boot/dts/picoxcell-pc7302-pc3x3.dts
deleted file mode 100644
index 3eca65e8ee09..000000000000
--- a/arch/arm/boot/dts/picoxcell-pc7302-pc3x3.dts
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2011 Picochip, Jamie Iles
- */
-
-/dts-v1/;
-/include/ "picoxcell-pc3x3.dtsi"
-/ {
-	model = "Picochip PC7302 (PC3X3)";
-	compatible = "picochip,pc7302-pc3x3", "picochip,pc3x3";
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x08000000>;
-	};
-
-	chosen {
-		stdout-path = &uart0;
-	};
-
-	clocks {
-		ref_clk: clock@10 {
-			compatible = "fixed-clock";
-			clock-outputs = "ref";
-			clock-frequency = <20000000>;
-		};
-
-		clkgate: clkgate@800a0048 {
-			clock@4 {
-				picochip,clk-no-disable;
-			};
-		};
-	};
-
-	rwid-axi {
-		ebi@50000000 {
-			nand: gpio-nand@2,0 {
-				compatible = "gpio-control-nand";
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <2 0x0000 0x1000>;
-				bus-clock = <&ebi_clk>, "bus";
-				gpio-control-nand,io-sync-reg =
-					<0x00000000 0x80220000>;
-
-				gpios = <&banka 1 0	/* rdy */
-					 &banka 2 0 	/* nce */
-					 &banka 3 0 	/* ale */
-					 &banka 4 0 	/* cle */
-					 0		/* nwp */>;
-
-				boot@100000 {
-					label = "Boot";
-					reg = <0x100000 0x80000>;
-				};
-
-				redundant-boot@200000 {
-					label = "Redundant Boot";
-					reg = <0x200000 0x80000>;
-				};
-
-				boot-env@300000 {
-					label = "Boot Evironment";
-					reg = <0x300000 0x20000>;
-				};
-
-				redundant-boot-env@320000 {
-					label = "Redundant Boot Environment";
-					reg = <0x300000 0x20000>;
-				};
-
-				kernel@380000 {
-					label = "Kernel";
-					reg = <0x380000 0x800000>;
-				};
-
-				fs@b80000 {
-					label = "File System";
-					reg = <0xb80000 0xf480000>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/prima2-evb.dts b/arch/arm/boot/dts/prima2-evb.dts
deleted file mode 100644
index 7394f764df65..000000000000
--- a/arch/arm/boot/dts/prima2-evb.dts
+++ /dev/null
@@ -1,37 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DTS file for CSR SiRFprimaII Evaluation Board
- *
- * Copyright (c) 2012 Cambridge Silicon Radio Limited, a CSR plc group company.
- */
-
-/dts-v1/;
-
-/include/ "prima2.dtsi"
-
-/ {
-	model = "CSR SiRFprimaII Evaluation Board";
-	compatible = "sirf,prima2", "sirf,prima2-cb";
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	axi {
-		peri-iobg {
-			uart@b0060000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&uart1_pins_a>;
-			};
-			spi@b00d0000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi0_pins_a>;
-			};
-			spi@b0170000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi1_pins_a>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/prima2.dtsi b/arch/arm/boot/dts/prima2.dtsi
deleted file mode 100644
index 9c7b46b90c3c..000000000000
--- a/arch/arm/boot/dts/prima2.dtsi
+++ /dev/null
@@ -1,838 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * DTS file for CSR SiRFprimaII SoC
- *
- * Copyright (c) 2012 Cambridge Silicon Radio Limited, a CSR plc group company.
- */
-
-/ {
-	compatible = "sirf,prima2";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&intc>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			compatible = "arm,cortex-a9";
-			device_type = "cpu";
-			reg = <0x0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <32768>;
-			i-cache-size = <32768>;
-			/* from bootloader */
-			timebase-frequency = <0>;
-			bus-frequency = <0>;
-			clock-frequency = <0>;
-			clocks = <&clks 12>;
-			operating-points = <
-				/* kHz    uV */
-				200000  1025000
-				400000  1025000
-				664000  1050000
-				800000  1100000
-			>;
-			clock-latency = <150000>;
-		};
-	};
-
-	arm-pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts = <29>;
-	};
-
-	axi {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x40000000 0x40000000 0x80000000>;
-
-		l2-cache-controller@80040000 {
-			compatible = "arm,pl310-cache";
-			reg = <0x80040000 0x1000>;
-			interrupts = <59>;
-			arm,tag-latency = <1 1 1>;
-			arm,data-latency = <1 1 1>;
-			arm,filter-ranges = <0 0x40000000>;
-		};
-
-		intc: interrupt-controller@80020000 {
-			#interrupt-cells = <1>;
-			interrupt-controller;
-			compatible = "sirf,prima2-intc";
-			reg = <0x80020000 0x1000>;
-		};
-
-		sys-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x88000000 0x88000000 0x40000>;
-
-			clks: clock-controller@88000000 {
-				compatible = "sirf,prima2-clkc";
-				reg = <0x88000000 0x1000>;
-				interrupts = <3>;
-				#clock-cells = <1>;
-			};
-
-			rstc: reset-controller@88010000 {
-				compatible = "sirf,prima2-rstc";
-				reg = <0x88010000 0x1000>;
-				#reset-cells = <1>;
-			};
-
-			rsc-controller@88020000 {
-				compatible = "sirf,prima2-rsc";
-				reg = <0x88020000 0x1000>;
-			};
-
-			cphifbg@88030000 {
-				compatible = "sirf,prima2-cphifbg";
-				reg = <0x88030000 0x1000>;
-				clocks = <&clks 42>;
-			};
-		};
-
-		mem-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x90000000 0x90000000 0x10000>;
-
-			memory-controller@90000000 {
-				compatible = "sirf,prima2-memc";
-				reg = <0x90000000 0x2000>;
-				interrupts = <27>;
-				clocks = <&clks 5>;
-			};
-
-			memc-monitor {
-				compatible = "sirf,prima2-memcmon";
-				reg = <0x90002000 0x200>;
-				interrupts = <4>;
-				clocks = <&clks 32>;
-			};
-		};
-
-		disp-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x90010000 0x90010000 0x30000>;
-
-			display@90010000 {
-				compatible = "sirf,prima2-lcd";
-				reg = <0x90010000 0x20000>;
-				interrupts = <30>;
-			};
-
-			vpp@90020000 {
-				compatible = "sirf,prima2-vpp";
-				reg = <0x90020000 0x10000>;
-				interrupts = <31>;
-				clocks = <&clks 35>;
-				resets = <&rstc 6>;
-			};
-		};
-
-		graphics-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x98000000 0x98000000 0x8000000>;
-
-			graphics@98000000 {
-				compatible = "powervr,sgx531";
-				reg = <0x98000000 0x8000000>;
-				interrupts = <6>;
-				clocks = <&clks 32>;
-			};
-		};
-
-		multimedia-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xa0000000 0xa0000000 0x8000000>;
-
-			multimedia@a0000000 {
-				compatible = "sirf,prima2-video-codec";
-				reg = <0xa0000000 0x8000000>;
-				interrupts = <5>;
-				clocks = <&clks 33>;
-			};
-		};
-
-		dsp-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xa8000000 0xa8000000 0x2000000>;
-
-			dspif@a8000000 {
-				compatible = "sirf,prima2-dspif";
-				reg = <0xa8000000 0x10000>;
-				interrupts = <9>;
-				resets = <&rstc 1>;
-			};
-
-			gps@a8010000 {
-				compatible = "sirf,prima2-gps";
-				reg = <0xa8010000 0x10000>;
-				interrupts = <7>;
-				clocks = <&clks 9>;
-				resets = <&rstc 2>;
-			};
-
-			dsp@a9000000 {
-				compatible = "sirf,prima2-dsp";
-				reg = <0xa9000000 0x1000000>;
-				interrupts = <8>;
-				clocks = <&clks 8>;
-				resets = <&rstc 0>;
-			};
-		};
-
-		peri-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xb0000000 0xb0000000 0x180000>,
-			       <0x56000000 0x56000000 0x1b00000>;
-
-			timer@b0020000 {
-				compatible = "sirf,prima2-tick";
-				reg = <0xb0020000 0x1000>;
-				interrupts = <0>;
-				clocks = <&clks 11>;
-			};
-
-			nand@b0030000 {
-				compatible = "sirf,prima2-nand";
-				reg = <0xb0030000 0x10000>;
-				interrupts = <41>;
-				clocks = <&clks 26>;
-			};
-
-			audio@b0040000 {
-				compatible = "sirf,prima2-audio";
-				reg = <0xb0040000 0x10000>;
-				interrupts = <35>;
-				clocks = <&clks 27>;
-			};
-
-			uart0: uart@b0050000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-uart";
-				reg = <0xb0050000 0x1000>;
-				interrupts = <17>;
-				fifosize = <128>;
-				clocks = <&clks 13>;
-				dmas = <&dmac1 5>, <&dmac0 2>;
-				dma-names = "rx", "tx";
-			};
-
-			uart1: uart@b0060000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-uart";
-				reg = <0xb0060000 0x1000>;
-				interrupts = <18>;
-				fifosize = <32>;
-				clocks = <&clks 14>;
-			};
-
-			uart2: uart@b0070000 {
-				cell-index = <2>;
-				compatible = "sirf,prima2-uart";
-				reg = <0xb0070000 0x1000>;
-				interrupts = <19>;
-				fifosize = <128>;
-				clocks = <&clks 15>;
-				dmas = <&dmac0 6>, <&dmac0 7>;
-				dma-names = "rx", "tx";
-			};
-
-			usp0: usp@b0080000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-usp";
-				reg = <0xb0080000 0x10000>;
-				interrupts = <20>;
-				fifosize = <128>;
-				clocks = <&clks 28>;
-				dmas = <&dmac1 1>, <&dmac1 2>;
-				dma-names = "rx", "tx";
-			};
-
-			usp1: usp@b0090000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-usp";
-				reg = <0xb0090000 0x10000>;
-				interrupts = <21>;
-				fifosize = <128>;
-				clocks = <&clks 29>;
-				dmas = <&dmac0 14>, <&dmac0 15>;
-				dma-names = "rx", "tx";
-			};
-
-			usp2: usp@b00a0000 {
-				cell-index = <2>;
-				compatible = "sirf,prima2-usp";
-				reg = <0xb00a0000 0x10000>;
-				interrupts = <22>;
-				fifosize = <128>;
-				clocks = <&clks 30>;
-				dmas = <&dmac0 10>, <&dmac0 11>;
-				dma-names = "rx", "tx";
-			};
-
-			dmac0: dma-controller@b00b0000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-dmac";
-				reg = <0xb00b0000 0x10000>;
-				interrupts = <12>;
-				clocks = <&clks 24>;
-				#dma-cells = <1>;
-			};
-
-			dmac1: dma-controller@b0160000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-dmac";
-				reg = <0xb0160000 0x10000>;
-				interrupts = <13>;
-				clocks = <&clks 25>;
-				#dma-cells = <1>;
-			};
-
-			vip@b00C0000 {
-				compatible = "sirf,prima2-vip";
-				reg = <0xb00C0000 0x10000>;
-				clocks = <&clks 31>;
-				interrupts = <14>;
-				sirf,vip-dma-rx-channel = <16>;
-			};
-
-			spi0: spi@b00d0000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-spi";
-				reg = <0xb00d0000 0x10000>;
-				interrupts = <15>;
-				sirf,spi-num-chipselects = <1>;
-				dmas = <&dmac1 9>,
-				     <&dmac1 4>;
-				dma-names = "rx", "tx";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				clocks = <&clks 19>;
-				status = "disabled";
-			};
-
-			spi1: spi@b0170000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-spi";
-				reg = <0xb0170000 0x10000>;
-				interrupts = <16>;
-				sirf,spi-num-chipselects = <1>;
-				dmas = <&dmac0 12>,
-				     <&dmac0 13>;
-				dma-names = "rx", "tx";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				clocks = <&clks 20>;
-				status = "disabled";
-			};
-
-			i2c0: i2c@b00e0000 {
-				cell-index = <0>;
-				compatible = "sirf,prima2-i2c";
-				reg = <0xb00e0000 0x10000>;
-				interrupts = <24>;
-				clocks = <&clks 17>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-			i2c1: i2c@b00f0000 {
-				cell-index = <1>;
-				compatible = "sirf,prima2-i2c";
-				reg = <0xb00f0000 0x10000>;
-				interrupts = <25>;
-				clocks = <&clks 18>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-			tsc@b0110000 {
-				compatible = "sirf,prima2-tsc";
-				reg = <0xb0110000 0x10000>;
-				interrupts = <33>;
-				clocks = <&clks 16>;
-			};
-
-			gpio: pinctrl@b0120000 {
-				#gpio-cells = <2>;
-				#interrupt-cells = <2>;
-				compatible = "sirf,prima2-pinctrl";
-				reg = <0xb0120000 0x10000>;
-				interrupts = <43 44 45 46 47>;
-				gpio-controller;
-				interrupt-controller;
-
-				lcd_16pins_a: lcd0@0 {
-					lcd {
-						sirf,pins = "lcd_16bitsgrp";
-						sirf,function = "lcd_16bits";
-					};
-				};
-				lcd_18pins_a: lcd0@1 {
-					lcd {
-						sirf,pins = "lcd_18bitsgrp";
-						sirf,function = "lcd_18bits";
-					};
-				};
-				lcd_24pins_a: lcd0@2 {
-					lcd {
-						sirf,pins = "lcd_24bitsgrp";
-						sirf,function = "lcd_24bits";
-					};
-				};
-				lcdrom_pins_a: lcdrom0@0 {
-					lcd {
-						sirf,pins = "lcdromgrp";
-						sirf,function = "lcdrom";
-					};
-				};
-				uart0_pins_a: uart0@0 {
-					uart {
-						sirf,pins = "uart0grp";
-						sirf,function = "uart0";
-					};
-				};
-				uart0_noflow_pins_a: uart0@1 {
-					uart {
-						sirf,pins = "uart0_nostreamctrlgrp";
-						sirf,function = "uart0_nostreamctrl";
-					};
-				};
-				uart1_pins_a: uart1@0 {
-					uart {
-						sirf,pins = "uart1grp";
-						sirf,function = "uart1";
-					};
-				};
-				uart2_pins_a: uart2@0 {
-					uart {
-						sirf,pins = "uart2grp";
-						sirf,function = "uart2";
-					};
-				};
-				uart2_noflow_pins_a: uart2@1 {
-					uart {
-						sirf,pins = "uart2_nostreamctrlgrp";
-						sirf,function = "uart2_nostreamctrl";
-					};
-				};
-				spi0_pins_a: spi0@0 {
-					spi {
-						sirf,pins = "spi0grp";
-						sirf,function = "spi0";
-					};
-				};
-				spi1_pins_a: spi1@0 {
-					spi {
-						sirf,pins = "spi1grp";
-						sirf,function = "spi1";
-					};
-				};
-				i2c0_pins_a: i2c0@0 {
-					i2c {
-						sirf,pins = "i2c0grp";
-						sirf,function = "i2c0";
-					};
-				};
-				i2c1_pins_a: i2c1@0 {
-					i2c {
-						sirf,pins = "i2c1grp";
-						sirf,function = "i2c1";
-					};
-				};
-                                pwm0_pins_a: pwm0@0 {
-                                        pwm {
-                                                sirf,pins = "pwm0grp";
-                                                sirf,function = "pwm0";
-                                        };
-                                };
-                                pwm1_pins_a: pwm1@0 {
-                                        pwm {
-                                                sirf,pins = "pwm1grp";
-                                                sirf,function = "pwm1";
-                                        };
-                                };
-                                pwm2_pins_a: pwm2@0 {
-                                        pwm {
-                                                sirf,pins = "pwm2grp";
-                                                sirf,function = "pwm2";
-                                        };
-                                };
-                                pwm3_pins_a: pwm3@0 {
-                                        pwm {
-                                                sirf,pins = "pwm3grp";
-                                                sirf,function = "pwm3";
-                                        };
-                                };
-                                gps_pins_a: gps@0 {
-                                        gps {
-                                                sirf,pins = "gpsgrp";
-                                                sirf,function = "gps";
-                                        };
-                                };
-                                vip_pins_a: vip@0 {
-                                        vip {
-                                                sirf,pins = "vipgrp";
-                                                sirf,function = "vip";
-                                        };
-                                };
-                                sdmmc0_pins_a: sdmmc0@0 {
-                                        sdmmc0 {
-                                                sirf,pins = "sdmmc0grp";
-                                                sirf,function = "sdmmc0";
-                                        };
-                                };
-                                sdmmc1_pins_a: sdmmc1@0 {
-                                        sdmmc1 {
-                                                sirf,pins = "sdmmc1grp";
-                                                sirf,function = "sdmmc1";
-                                        };
-                                };
-                                sdmmc2_pins_a: sdmmc2@0 {
-                                        sdmmc2 {
-                                                sirf,pins = "sdmmc2grp";
-                                                sirf,function = "sdmmc2";
-                                        };
-                                };
-                                sdmmc3_pins_a: sdmmc3@0 {
-                                        sdmmc3 {
-                                                sirf,pins = "sdmmc3grp";
-                                                sirf,function = "sdmmc3";
-                                        };
-                                };
-                                sdmmc4_pins_a: sdmmc4@0 {
-                                        sdmmc4 {
-                                                sirf,pins = "sdmmc4grp";
-                                                sirf,function = "sdmmc4";
-                                        };
-                                };
-                                sdmmc5_pins_a: sdmmc5@0 {
-                                        sdmmc5 {
-                                                sirf,pins = "sdmmc5grp";
-                                                sirf,function = "sdmmc5";
-                                        };
-                                };
-				i2s_mclk_pins_a: i2s_mclk@0 {
-                                        i2s_mclk {
-                                                sirf,pins = "i2smclkgrp";
-                                                sirf,function = "i2s_mclk";
-                                        };
-                                };
-				i2s_ext_clk_input_pins_a: i2s_ext_clk_input@0 {
-                                        i2s_ext_clk_input {
-                                                sirf,pins = "i2s_ext_clk_inputgrp";
-                                                sirf,function = "i2s_ext_clk_input";
-                                        };
-                                };
-                                i2s_pins_a: i2s@0 {
-                                        i2s {
-                                                sirf,pins = "i2sgrp";
-                                                sirf,function = "i2s";
-                                        };
-                                };
-				i2s_no_din_pins_a: i2s_no_din@0 {
-                                        i2s_no_din {
-                                                sirf,pins = "i2s_no_dingrp";
-                                                sirf,function = "i2s_no_din";
-                                        };
-                                };
-				i2s_6chn_pins_a: i2s_6chn@0 {
-                                        i2s_6chn {
-                                                sirf,pins = "i2s_6chngrp";
-                                                sirf,function = "i2s_6chn";
-                                        };
-                                };
-                                ac97_pins_a: ac97@0 {
-                                        ac97 {
-                                                sirf,pins = "ac97grp";
-                                                sirf,function = "ac97";
-                                        };
-                                };
-                                nand_pins_a: nand@0 {
-                                        nand {
-                                                sirf,pins = "nandgrp";
-                                                sirf,function = "nand";
-                                        };
-                                };
-                                usp0_pins_a: usp0@0 {
-                                        usp0 {
-                                                sirf,pins = "usp0grp";
-                                                sirf,function = "usp0";
-                                        };
-                                };
-				usp0_uart_nostreamctrl_pins_a: usp0@1 {
-                                        usp0 {
-                                                sirf,pins =
-							"usp0_uart_nostreamctrl_grp";
-                                                sirf,function =
-							"usp0_uart_nostreamctrl";
-                                        };
-                                };
-                                usp0_only_utfs_pins_a: usp0@2 {
-                                        usp0 {
-                                                sirf,pins = "usp0_only_utfs_grp";
-                                                sirf,function = "usp0_only_utfs";
-                                        };
-                                };
-                                usp0_only_urfs_pins_a: usp0@3 {
-                                        usp0 {
-                                                sirf,pins = "usp0_only_urfs_grp";
-                                                sirf,function = "usp0_only_urfs";
-                                        };
-                                };
-                                usp1_pins_a: usp1@0 {
-                                        usp1 {
-                                                sirf,pins = "usp1grp";
-                                                sirf,function = "usp1";
-                                        };
-                                };
-				usp1_uart_nostreamctrl_pins_a: usp1@1 {
-                                        usp1 {
-                                                sirf,pins =
-							"usp1_uart_nostreamctrl_grp";
-                                                sirf,function =
-							"usp1_uart_nostreamctrl";
-                                        };
-                                };
-                                usp2_pins_a: usp2@0 {
-                                        usp2 {
-                                                sirf,pins = "usp2grp";
-                                                sirf,function = "usp2";
-                                        };
-                                };
-				usp2_uart_nostreamctrl_pins_a: usp2@1 {
-                                        usp2 {
-                                                sirf,pins =
-							"usp2_uart_nostreamctrl_grp";
-                                                sirf,function =
-							"usp2_uart_nostreamctrl";
-                                        };
-                                };
-                                usb0_utmi_drvbus_pins_a: usb0_utmi_drvbus@0 {
-                                        usb0_utmi_drvbus {
-                                                sirf,pins = "usb0_utmi_drvbusgrp";
-                                                sirf,function = "usb0_utmi_drvbus";
-                                        };
-                                };
-                                usb1_utmi_drvbus_pins_a: usb1_utmi_drvbus@0 {
-                                        usb1_utmi_drvbus {
-                                                sirf,pins = "usb1_utmi_drvbusgrp";
-                                                sirf,function = "usb1_utmi_drvbus";
-                                        };
-                                };
-                                usb1_dp_dn_pins_a: usb1_dp_dn@0 {
-                                        usb1_dp_dn {
-                                                sirf,pins = "usb1_dp_dngrp";
-                                                sirf,function = "usb1_dp_dn";
-                                        };
-                                };
-                                uart1_route_io_usb1_pins_a: uart1_route_io_usb1@0 {
-                                        uart1_route_io_usb1 {
-                                                sirf,pins = "uart1_route_io_usb1grp";
-                                                sirf,function = "uart1_route_io_usb1";
-                                        };
-                                };
-                                warm_rst_pins_a: warm_rst@0 {
-                                        warm_rst {
-                                                sirf,pins = "warm_rstgrp";
-                                                sirf,function = "warm_rst";
-                                        };
-                                };
-                                pulse_count_pins_a: pulse_count@0 {
-                                        pulse_count {
-                                                sirf,pins = "pulse_countgrp";
-                                                sirf,function = "pulse_count";
-                                        };
-                                };
-                                cko0_pins_a: cko0@0 {
-                                        cko0 {
-                                                sirf,pins = "cko0grp";
-                                                sirf,function = "cko0";
-                                        };
-                                };
-                                cko1_pins_a: cko1@0 {
-                                        cko1 {
-                                                sirf,pins = "cko1grp";
-                                                sirf,function = "cko1";
-                                        };
-                                };
-			};
-
-			pwm@b0130000 {
-				compatible = "sirf,prima2-pwm";
-				reg = <0xb0130000 0x10000>;
-				clocks = <&clks 21>;
-			};
-
-			efusesys@b0140000 {
-				compatible = "sirf,prima2-efuse";
-				reg = <0xb0140000 0x10000>;
-				clocks = <&clks 22>;
-			};
-
-			pulsec@b0150000 {
-				compatible = "sirf,prima2-pulsec";
-				reg = <0xb0150000 0x10000>;
-				interrupts = <48>;
-				clocks = <&clks 23>;
-			};
-
-			pci-iobg {
-				compatible = "sirf,prima2-pciiobg", "simple-bus";
-				#address-cells = <1>;
-				#size-cells = <1>;
-				ranges = <0x56000000 0x56000000 0x1b00000>;
-
-				sd0: sdhci@56000000 {
-					cell-index = <0>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56000000 0x100000>;
-					interrupts = <38>;
-					status = "disabled";
-					bus-width = <8>;
-					clocks = <&clks 36>;
-				};
-
-				sd1: sdhci@56100000 {
-					cell-index = <1>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56100000 0x100000>;
-					interrupts = <38>;
-					status = "disabled";
-					bus-width = <4>;
-					clocks = <&clks 36>;
-				};
-
-				sd2: sdhci@56200000 {
-					cell-index = <2>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56200000 0x100000>;
-					interrupts = <23>;
-					status = "disabled";
-					clocks = <&clks 37>;
-				};
-
-				sd3: sdhci@56300000 {
-					cell-index = <3>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56300000 0x100000>;
-					interrupts = <23>;
-					status = "disabled";
-					clocks = <&clks 37>;
-				};
-
-				sd4: sdhci@56400000 {
-					cell-index = <4>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56400000 0x100000>;
-					interrupts = <39>;
-					status = "disabled";
-					clocks = <&clks 38>;
-				};
-
-				sd5: sdhci@56500000 {
-					cell-index = <5>;
-					compatible = "sirf,prima2-sdhc";
-					reg = <0x56500000 0x100000>;
-					interrupts = <39>;
-					clocks = <&clks 38>;
-				};
-
-				pci-copy@57900000 {
-					compatible = "sirf,prima2-pcicp";
-					reg = <0x57900000 0x100000>;
-					interrupts = <40>;
-				};
-
-				rom-interface@57a00000 {
-					compatible = "sirf,prima2-romif";
-					reg = <0x57a00000 0x100000>;
-				};
-			};
-		};
-
-		rtc-iobg {
-			compatible = "sirf,prima2-rtciobg", "sirf-prima2-rtciobg-bus", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x80030000 0x10000>;
-
-			gpsrtc@1000 {
-				compatible = "sirf,prima2-gpsrtc";
-				reg = <0x1000 0x1000>;
-				interrupts = <55 56 57>;
-			};
-
-			sysrtc@2000 {
-				compatible = "sirf,prima2-sysrtc";
-				reg = <0x2000 0x1000>;
-				interrupts = <52 53 54>;
-			};
-
-			minigpsrtc@2000 {
-				compatible = "sirf,prima2-minigpsrtc";
-				reg = <0x2000 0x1000>;
-				interrupts = <54>;
-			};
-
-			pwrc@3000 {
-				compatible = "sirf,prima2-pwrc";
-				reg = <0x3000 0x1000>;
-				interrupts = <32>;
-			};
-		};
-
-		uus-iobg {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xb8000000 0xb8000000 0x40000>;
-
-			usb0: usb@b00e0000 {
-				compatible = "chipidea,ci13611a-prima2";
-				reg = <0xb8000000 0x10000>;
-				interrupts = <10>;
-				clocks = <&clks 40>;
-			};
-
-			usb1: usb@b00f0000 {
-				compatible = "chipidea,ci13611a-prima2";
-				reg = <0xb8010000 0x10000>;
-				interrupts = <11>;
-				clocks = <&clks 41>;
-			};
-
-			sata@b00f0000 {
-				compatible = "synopsys,dwc-ahsata";
-				reg = <0xb8020000 0x10000>;
-				interrupts = <37>;
-			};
-
-			security@b00f0000 {
-				compatible = "sirf,prima2-security";
-				reg = <0xb8030000 0x10000>;
-				interrupts = <42>;
-				clocks = <&clks 7>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/pxa910-dkb.dts b/arch/arm/boot/dts/pxa910-dkb.dts
deleted file mode 100644
index 0f899e672e82..000000000000
--- a/arch/arm/boot/dts/pxa910-dkb.dts
+++ /dev/null
@@ -1,172 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2012 Marvell Technology Group Ltd.
- *  Author: Haojian Zhuang <haojian.zhuang@marvell.com>
- */
-
-/dts-v1/;
-#include "pxa910.dtsi"
-
-/ {
-	model = "Marvell PXA910 DKB Development Board";
-	compatible = "mrvl,pxa910-dkb", "mrvl,pxa910";
-
-	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on";
-	};
-
-	memory {
-		reg = <0x00000000 0x10000000>;
-	};
-
-	soc {
-		apb@d4000000 {
-			uart1: uart@d4017000 {
-				status = "okay";
-			};
-			twsi1: i2c@d4011000 {
-				status = "okay";
-
-				pmic: 88pm860x@34 {
-					compatible = "marvell,88pm860x";
-					reg = <0x34>;
-					interrupts = <4>;
-					interrupt-parent = <&intc>;
-					interrupt-controller;
-					#interrupt-cells = <1>;
-
-					marvell,88pm860x-irq-read-clr;
-					marvell,88pm860x-slave-addr = <0x11>;
-
-					regulators {
-						BUCK1 {
-							regulator-min-microvolt = <1000000>;
-							regulator-max-microvolt = <1500000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						BUCK2 {
-							regulator-min-microvolt = <1000000>;
-							regulator-max-microvolt = <1500000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						BUCK3 {
-							regulator-min-microvolt = <1000000>;
-							regulator-max-microvolt = <3000000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO1 {
-							regulator-min-microvolt = <1200000>;
-							regulator-max-microvolt = <2800000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO2 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO3 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO4 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-always-on;
-						};
-						LDO5 {
-							regulator-min-microvolt = <2900000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO6 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO7 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <2900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO8 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <2900000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO9 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO10 {
-							regulator-min-microvolt = <1200000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-boot-on;
-							regulator-always-on;
-						};
-						LDO12 {
-							regulator-min-microvolt = <1200000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-always-on;
-						};
-						LDO13 {
-							regulator-min-microvolt = <1200000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-always-on;
-						};
-						LDO14 {
-							regulator-min-microvolt = <1800000>;
-							regulator-max-microvolt = <3300000>;
-							regulator-always-on;
-						};
-					};
-					rtc {
-						marvell,88pm860x-vrtc = <1>;
-					};
-					touch {
-						marvell,88pm860x-gpadc-prebias = <1>;
-						marvell,88pm860x-gpadc-slot-cycle = <1>;
-						marvell,88pm860x-tsi-prebias = <6>;
-						marvell,88pm860x-pen-prebias = <16>;
-						marvell,88pm860x-pen-prechg = <2>;
-						marvell,88pm860x-resistor-X = <300>;
-					};
-					backlights {
-						backlight-0 {
-							marvell,88pm860x-iset = <4>;
-							marvell,88pm860x-pwm = <3>;
-						};
-						backlight-2 {
-						};
-					};
-					leds {
-						led0-red {
-							marvell,88pm860x-iset = <12>;
-						};
-						led0-green {
-							marvell,88pm860x-iset = <12>;
-						};
-						led0-blue {
-							marvell,88pm860x-iset = <12>;
-						};
-					};
-				};
-			};
-			rtc: rtc@d4010000 {
-				status = "okay";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
deleted file mode 100644
index 4e6c50d45cb2..000000000000
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ /dev/null
@@ -1,960 +0,0 @@
-/*
- * Copyright 2016 Linaro Ltd
- *
- * Permission is hereby granted, free of charge, to any person obtaining a copy
- * of this software and associated documentation files (the "Software"), to deal
- * in the Software without restriction, including without limitation the rights
- * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
- * copies of the Software, and to permit persons to whom the Software is
- * furnished to do so, subject to the following conditions:
- *
- * The above copyright notice and this permission notice shall be included in
- * all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
- * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
- * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
- * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
- * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
- * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
- * THE SOFTWARE.
- */
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
-#include "qcom-msm8660.dtsi"
-
-/ {
-	model = "Qualcomm APQ8060 Dragonboard";
-	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
-
-	aliases {
-		serial0 = &gsbi12_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	regulators {
-		compatible = "simple-bus";
-
-		/* Main power of the board: 3.7V */
-		vph: regulator-fixed {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <3700000>;
-			regulator-max-microvolt = <3700000>;
-			regulator-name = "VPH";
-			regulator-type = "voltage";
-			regulator-always-on;
-			regulator-boot-on;
-		};
-
-		/* GPIO controlled ethernet power regulator */
-		dragon_veth: xc622a331mrg {
-			compatible = "regulator-fixed";
-			regulator-name = "XC6222A331MR-G";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vph>;
-			gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			pinctrl-names = "default";
-			pinctrl-0 = <&dragon_veth_gpios>;
-			regulator-always-on;
-		};
-
-		/* VDDvario fixed regulator */
-		dragon_vario: nds332p {
-			compatible = "regulator-fixed";
-			regulator-name = "NDS332P";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			vin-supply = <&pm8058_s3>;
-		};
-
-		/* This is a levelshifter for SDCC5 */
-		dragon_vio_txb: txb0104rgyr {
-			compatible = "regulator-fixed";
-			regulator-name = "Dragon SDCC levelshifter";
-			vin-supply = <&pm8058_l14>;
-			regulator-always-on;
-		};
-	};
-
-	/*
-	 * Capella CM3605 light and proximity sensor mounted directly
-	 * on the sensor board.
-	 */
-	cm3605 {
-		compatible = "capella,cm3605";
-		vdd-supply = <&pm8058_l14>; // 2.85V
-		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
-		capella,aset-resistance-ohms = <100000>;
-		/* Trig on both edges - getting close or far away */
-		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
-		/* MPP05 analog input to the XOADC */
-		io-channels = <&xoadc 0x00 0x05>;
-		io-channel-names = "aout";
-		pinctrl-names = "default";
-		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
-	};
-
-	soc {
-		pinctrl@800000 {
-			/* eMMMC pins, all 8 data lines connected */
-			dragon_sdcc1_pins: sdcc1 {
-				mux {
-					pins = "gpio159", "gpio160", "gpio161",
-					     "gpio162", "gpio163", "gpio164",
-					     "gpio165", "gpio166", "gpio167",
-					     "gpio168";
-					     function = "sdc1";
-				};
-				clk {
-					pins = "gpio167"; /* SDC1 CLK */
-					drive-strength = <16>;
-					bias-disable;
-				};
-				cmd {
-					pins = "gpio168"; /* SDC1 CMD */
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-				data {
-					/* SDC1 D0 to D7 */
-					pins = "gpio159", "gpio160", "gpio161", "gpio162",
-					     "gpio163", "gpio164", "gpio165", "gpio166";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			/*
-			 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
-			 * configuration.
-			 */
-			dragon_sdcc3_pins: sdcc3 {
-				clk {
-					pins = "sdc3_clk";
-					drive-strength = <8>;
-					bias-disable;
-				};
-				cmd {
-					pins = "sdc3_cmd";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-				data {
-					pins = "sdc3_data";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-			};
-
-			/* Second SD card slot pins */
-			dragon_sdcc5_pins: sdcc5 {
-				mux {
-					pins = "gpio95", "gpio96", "gpio97",
-					    "gpio98", "gpio99", "gpio100";
-					function = "sdc5";
-				};
-				clk {
-					pins = "gpio97"; /* SDC5 CLK */
-					drive-strength = <16>;
-					bias-disable;
-				};
-				cmd {
-					pins = "gpio95"; /* SDC5 CMD */
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-				data {
-					/* SDC5 D0 to D3 */
-					pins = "gpio96", "gpio98", "gpio99", "gpio100";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			dragon_gsbi8_i2c_pins: gsbi8_i2c {
-				mux {
-					pins = "gpio64", "gpio65";
-					function = "gsbi8";
-				};
-				pinconf {
-					pins = "gpio64", "gpio65";
-					drive-strength = <16>;
-					/* These have external pull-up 2.2kOhm to 1.8V */
-					bias-disable;
-				};
-			};
-
-			dragon_gsbi12_i2c_pins: gsbi12_i2c {
-				mux {
-					pins = "gpio115", "gpio116";
-					function = "gsbi12";
-				};
-				pinconf {
-					pins = "gpio115", "gpio116";
-					drive-strength = <16>;
-					/* These have external pull-up 4.7kOhm to 1.8V */
-					bias-disable;
-				};
-			};
-
-			/* Primary serial port uart 0 pins */
-			dragon_gsbi12_serial_pins: gsbi12_serial {
-				mux {
-					pins = "gpio117", "gpio118";
-					function = "gsbi12";
-				};
-				tx {
-					pins = "gpio117";
-					drive-strength = <8>;
-					bias-disable;
-				};
-				rx {
-					pins = "gpio118";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-			};
-
-			dragon_ebi2_pins: ebi2 {
-				/*
-				 * Pins used by EBI2 on the Dragonboard, actually only
-				 * CS2 is used by a real peripheral. CS0 is just
-				 * routed to a test point.
-				 */
-				mux0 {
-					pins =
-					    /* "gpio39", CS1A_N this is not good to mux */
-					    "gpio40", /* CS2A_N */
-					    "gpio134"; /* CS0_N testpoint TP29 */
-					function = "ebi2cs";
-				};
-				mux1 {
-					pins =
-					    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
-					    "gpio123", "gpio124", "gpio125", "gpio126",
-					    "gpio127", "gpio128", "gpio129", "gpio130",
-					    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
-					    "gpio135", "gpio136", "gpio137", "gpio138",
-					    "gpio139", "gpio140", "gpio141", "gpio142",
-					    "gpio143", "gpio144", "gpio145", "gpio146",
-					    "gpio147", "gpio148", "gpio149", "gpio150",
-					    "gpio151", /* EBI2_OE_N */
-					    "gpio153", /* EBI2_ADV */
-					    "gpio157"; /* EBI2_WE_N */
-					function = "ebi2";
-				};
-			};
-
-			/* Interrupt line for the KXSD9 accelerometer */
-			dragon_kxsd9_gpios: kxsd9 {
-				irq {
-					pins = "gpio57"; /* IRQ line */
-					bias-pull-up;
-				};
-			};
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				keypad@148 {
-					linux,keymap = <
-					MATRIX_KEY(0, 0, KEY_MENU)
-					MATRIX_KEY(0, 2, KEY_1)
-					MATRIX_KEY(0, 3, KEY_4)
-					MATRIX_KEY(0, 4, KEY_7)
-					MATRIX_KEY(1, 0, KEY_UP)
-					MATRIX_KEY(1, 1, KEY_LEFT)
-					MATRIX_KEY(1, 2, KEY_DOWN)
-					MATRIX_KEY(1, 3, KEY_5)
-					MATRIX_KEY(1, 3, KEY_8)
-					MATRIX_KEY(2, 0, KEY_HOME)
-					MATRIX_KEY(2, 1, KEY_REPLY)
-					MATRIX_KEY(2, 2, KEY_2)
-					MATRIX_KEY(2, 3, KEY_6)
-					MATRIX_KEY(3, 0, KEY_VOLUMEUP)
-					MATRIX_KEY(3, 1, KEY_RIGHT)
-					MATRIX_KEY(3, 2, KEY_3)
-					MATRIX_KEY(3, 3, KEY_9)
-					MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
-					MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
-					MATRIX_KEY(4, 1, KEY_BACK)
-					MATRIX_KEY(4, 2, KEY_CAMERA)
-					MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
-					>;
-					keypad,num-rows = <6>;
-					keypad,num-columns = <5>;
-				};
-
-				gpio@150 {
-					dragon_ethernet_gpios: ethernet-gpios {
-						pinconf {
-							pins = "gpio7";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_bmp085_gpios: bmp085-gpios {
-						pinconf {
-							pins = "gpio16";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_mpu3050_gpios: mpu3050-gpios {
-						pinconf {
-							pins = "gpio17";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_sdcc3_gpios: sdcc3-gpios {
-						pinconf {
-							pins = "gpio22";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_sdcc5_gpios: sdcc5-gpios {
-						pinconf {
-							pins = "gpio26";
-							function = "normal";
-							input-enable;
-							bias-pull-up;
-							qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_ak8975_gpios: ak8975-gpios {
-						pinconf {
-							pins = "gpio33";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_cm3605_gpios: cm3605-gpios {
-						/* Pin 34 connected to the proxy IRQ */
-						pinconf_gpio34 {
-							pins = "gpio34";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-						/* Pin 35 connected to ASET */
-						pinconf_gpio35 {
-							pins = "gpio35";
-							function = "normal";
-							output-high;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_veth_gpios: veth-gpios {
-						pinconf {
-							pins = "gpio40";
-							function = "normal";
-							bias-disable;
-							drive-push-pull;
-						};
-					};
-				};
-
-				mpps@50 {
-					dragon_cm3605_mpps: cm3605-mpps {
-						pinconf {
-							pins = "mpp5";
-							function = "analog";
-							input-enable;
-							bias-high-impedance;
-							/* Let's use channel 5 */
-							qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-				};
-
-				xoadc@197 {
-					/* Reference voltage 2.2 V */
-					xoadc-ref-supply = <&pm8058_l18>;
-
-					/* Board-specific channels */
-					mpp5@5 {
-						/* Connected to AOUT of ALS sensor */
-						reg = <0x00 0x05>;
-					};
-					mpp6@6 {
-						/* Connected to test point TP43 */
-						reg = <0x00 0x06>;
-					};
-					mpp7@7 {
-						/* Connected to battery thermistor */
-						reg = <0x00 0x07>;
-					};
-					mpp8@8 {
-						/* Connected to battery ID detector */
-						reg = <0x00 0x08>;
-					};
-					mpp9@9 {
-						/* Connected to XO thermistor */
-						reg = <0x00 0x09>;
-					};
-				};
-
-				led@48 {
-					/*
-					 * The keypad LED @0x48 is routed to
-					 * the sensor board where it is
-					 * connected to an infrared LED
-					 * SFH4650 (60mW, @850nm) next to the
-					 * ambient light and proximity sensor
-					 * Capella Microsystems CM3605.
-					 */
-					compatible = "qcom,pm8058-keypad-led";
-					reg = <0x48>;
-					label = "pm8058:infrared:proximitysensor";
-					default-state = "off";
-					linux,default-trigger = "cm3605";
-				};
-				led@131 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x131>;
-					label = "pm8058:red";
-					default-state = "off";
-				};
-				led@132 {
-					/*
-					 * This is actually green too on my
-					 * board, but documented as yellow.
-					 */
-					compatible = "qcom,pm8058-led";
-					reg = <0x132>;
-					label = "pm8058:yellow";
-					default-state = "off";
-					linux,default-trigger = "mmc0";
-				};
-				led@133 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x133>;
-					label = "pm8058:green";
-					default-state = "on";
-					linux,default-trigger = "heartbeat";
-				};
-			};
-		};
-
-		gsbi@19800000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@19880000 {
-				status = "ok";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
-
-				eeprom@52 {
-					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					vcc-supply = <&pm8058_s3>;
-					pagesize = <64>;
-				};
-				wm8903: wm8903@1a {
-					/* This Woolfson Micro device has an unrouted interrupt line */
-					compatible = "wlf,wm8903";
-					reg = <0x1a>;
-
-					AVDD-supply = <&pm8058_l16>;
-					CPVDD-supply = <&pm8058_l16>;
-					DBVDD-supply = <&pm8058_s3>;
-					DCVDD-supply = <&pm8058_l0>;
-
-					gpio-controller;
-					#gpio-cells = <2>;
-
-					micdet-cfg = <0>;
-					micdet-delay = <100>;
-					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
-				};
-			};
-		};
-
-		gsbi@19c00000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@19c40000 {
-				status = "ok";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi12_serial_pins>;
-			};
-
-			i2c@19c80000 {
-				status = "ok";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
-
-				ak8975@c {
-					compatible = "asahi-kasei,ak8975";
-					reg = <0x0c>;
-					interrupt-parent = <&pm8058_gpio>;
-					interrupts = <33 IRQ_TYPE_EDGE_RISING>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_ak8975_gpios>;
-					vid-supply = <&pm8058_lvs0>; // 1.8V
-					vdd-supply = <&pm8058_l14>; // 2.85V
-				};
-				bmp085@77 {
-					compatible = "bosch,bmp085";
-					reg = <0x77>;
-					interrupt-parent = <&pm8058_gpio>;
-					interrupts = <16 IRQ_TYPE_EDGE_RISING>;
-					reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_bmp085_gpios>;
-					vddd-supply = <&pm8058_lvs0>; // 1.8V
-					vdda-supply = <&pm8058_l14>; // 2.85V
-				};
-				mpu3050@68 {
-					compatible = "invensense,mpu3050";
-					reg = <0x68>;
-					/*
-					 * GPIO17 is pulled high by a 10k
-					 * resistor to VLOGIC so needs to be
-					 * active low/falling edge.
-					 */
-					interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_mpu3050_gpios>;
-					vlogic-supply = <&pm8058_lvs0>; // 1.8V
-					vdd-supply = <&pm8058_l14>; // 2.85V
-
-					/*
-					 * The MPU-3050 acts as a hub for the
-					 * accelerometer.
-					 */
-					i2c-gate {
-						#address-cells = <1>;
-						#size-cells = <0>;
-
-						kxsd9@18 {
-							compatible = "kionix,kxsd9";
-							reg = <0x18>;
-							interrupt-parent = <&tlmm>;
-							interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
-							pinctrl-names = "default";
-							pinctrl-0 = <&dragon_kxsd9_gpios>;
-							iovdd-supply = <&pm8058_lvs0>; // 1.8V
-							vdd-supply = <&pm8058_l14>; // 2.85V
-						};
-					};
-				};
-			};
-		};
-
-		external-bus@1a100000 {
-			/* The EBI2 will instantiate first, then populate its children */
-			status = "ok";
-			pinctrl-names = "default";
-			pinctrl-0 = <&dragon_ebi2_pins>;
-
-			/*
-			 * An on-board SMSC LAN9221 chip for "debug ethernet",
-			 * which is actually just an ordinary ethernet on the
-			 * EBI2. This has a 25MHz chrystal next to it, so no
-			 * clocking is needed.
-			 */
-			ethernet-ebi2@2,0 {
-				compatible = "smsc,lan9221", "smsc,lan9115";
-				reg = <2 0x0 0x100>;
-				/*
-				 * The second interrupt is the PME interrupt
-				 * for network wakeup, connected to the TLMM.
-				 */
-				interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
-						    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
-				reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
-				vdd33a-supply = <&dragon_veth>;
-				vddvario-supply = <&dragon_vario>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_ethernet_gpios>;
-				phy-mode = "mii";
-				reg-io-width = <2>;
-				smsc,force-external-phy;
-				/* IRQ on edge falling = active low */
-				smsc,irq-active-low;
-				smsc,irq-push-pull;
-
-				/*
-				 * SLOW chipselect config
-				 * Delay 9 cycles (140ns@64MHz) between SMSC
-				 * LAN9221 Ethernet controller reads and writes
-				 * on CS2.
-				 */
-				qcom,xmem-recovery-cycles = <0>;
-				qcom,xmem-write-hold-cycles = <3>;
-				qcom,xmem-write-delta-cycles = <31>;
-				qcom,xmem-read-delta-cycles = <28>;
-				qcom,xmem-write-wait-cycles = <9>;
-				qcom,xmem-read-wait-cycles = <9>;
-			};
-		};
-
-		rpm@104000 {
-			/*
-			 * Set up of the PMIC RPM regulators for this board
-			 * PM8901 supplies "preliminary regulators" whatever
-			 * that means
-			 */
-			pm8901-regulators {
-				vdd_l0-supply = <&pm8901_s4>;
-				vdd_l1-supply = <&vph>;
-				vdd_l2-supply = <&vph>;
-				vdd_l3-supply = <&vph>;
-				vdd_l4-supply = <&vph>;
-				vdd_l5-supply = <&vph>;
-				vdd_l6-supply = <&vph>;
-				/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				lvs0_in-supply = <&pm8058_s3>;
-				lvs1_in-supply = <&pm8901_s4>;
-				lvs2_in-supply = <&pm8058_l0>;
-				lvs3_in-supply = <&pm8058_s2>;
-				mvs_in-supply = <&pm8058_s3>;
-
-				l0 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l1 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l2 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l3 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l4 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l6 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					bias-pull-down;
-				};
-
-				/* s0 and s1 are SAW regulators controlled over SPM */
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s3 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s4 {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* LVS0 thru 3 and mvs0 are just switches */
-				lvs0 {
-					regulator-always-on;
-				};
-				lvs1 { };
-				lvs2 { };
-				lvs3 { };
-				mvs0 {};
-
-			};
-
-			pm8058-regulators {
-				vdd_l0_l1_lvs-supply = <&pm8058_s3>;
-				vdd_l2_l11_l12-supply = <&vph>;
-				vdd_l3_l4_l5-supply = <&vph>;
-				vdd_l6_l7-supply = <&vph>;
-				vdd_l8-supply = <&vph>;
-				vdd_l9-supply = <&vph>;
-				vdd_l10-supply = <&vph>;
-				vdd_l13_l16-supply = <&pm8058_s4>;
-				vdd_l14_l15-supply = <&vph>;
-				vdd_l17_l18-supply = <&vph>;
-				vdd_l19_l20-supply = <&vph>;
-				vdd_l21-supply = <&pm8058_s3>;
-				vdd_l22-supply = <&pm8058_s3>;
-				vdd_l23_l24_l25-supply = <&pm8058_s3>;
-				vdd_s0-supply = <&vph>;
-				vdd_s1-supply = <&vph>;
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				vdd_ncp-supply = <&vph>;
-
-				l0 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l1 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l2 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l3 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l4 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l6 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3600000>;
-					bias-pull-down;
-				};
-				l7 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l8 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <3050000>;
-					bias-pull-down;
-				};
-				l9 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l10 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l11 {
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1500000>;
-					bias-pull-down;
-				};
-				l12 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-				l13 {
-					regulator-min-microvolt = <2050000>;
-					regulator-max-microvolt = <2050000>;
-					bias-pull-down;
-				};
-				l14 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-				};
-				l15 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l16 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-				l17 {
-					// 1.5V according to schematic
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l18 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					bias-pull-down;
-				};
-				l19 {
-					regulator-min-microvolt = <2500000>;
-					regulator-max-microvolt = <2500000>;
-					bias-pull-down;
-				};
-				l20 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l21 {
-					// 1.1 V according to schematic
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-				l22 {
-					// 1.2 V according to schematic
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-				l23 {
-					// Unused
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l24 {
-					// Unused
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l25 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				s0 {
-					// regulator-min-microvolt = <500000>;
-					// regulator-max-microvolt = <1325000>;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s1 {
-					// regulator-min-microvolt = <500000>;
-					// regulator-max-microvolt = <1250000>;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s2 {
-					// 1.3 V according to schematic
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s3 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-				s4 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-
-				/* LVS0 and LVS1 are just switches */
-				lvs0 {
-					bias-pull-down;
-				};
-				lvs1 {
-					bias-pull-down;
-				};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-		amba {
-			/* Internal 3.69 GiB eMMC */
-			sdcc@12400000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc1_pins>;
-				vmmc-supply = <&pm8901_l5>;
-				vqmmc-supply = <&pm8901_lvs0>;
-			};
-
-			/* External micro SD card, directly connected, pulled up to 2.85 V */
-			sdcc@12180000 {
-				status = "okay";
-				/* Enable SSBI GPIO 22 as input, use for card detect */
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
-				cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
-				wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
-				vmmc-supply = <&pm8058_l14>;
-			};
-
-			/*
-			 * Second external micro SD card, using two TXB104RGYR levelshifters
-			 * to lift from 1.8 V to 2.85 V
-			 */
-			sdcc@12200000 {
-				status = "okay";
-				/* Enable SSBI GPIO 26 as input, use for card detect */
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
-				cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
-				wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
-				vmmc-supply = <&pm8058_l14>;
-				vqmmc-supply = <&dragon_vio_txb>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
deleted file mode 100644
index a701d4bac320..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ /dev/null
@@ -1,359 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-/ {
-	model = "Asus Nexus7(flo)";
-	compatible = "asus,nexus7-flo", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-		serial1 = &gsbi6_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		ramoops@88d00000{
-			compatible = "ramoops";
-			reg = <0x88d00000 0x100000>;
-			record-size     = <0x00020000>;
-			console-size    = <0x00020000>;
-			ftrace-size     = <0x00020000>;
-		};
-	};
-
-	ext_3p3v: regulator-fixed@1 {
-		compatible = "regulator-fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-name = "ext_3p3v";
-		regulator-type = "voltage";
-		startup-delay-us = <0>;
-		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-boot-on;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		volume_up {
-			label = "Volume Up";
-			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-		volume_down {
-			label = "Volume Down";
-			gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	soc {
-		rpm@108000 {
-			regulators {
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vin_lvs2-supply = <&pm8921_s1>;
-
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-				vdd_ncp-supply = <&pm8921_l6>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				/* msm otg HSUSB_VDDCX */
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				/*
-				 * msm_sdcc.1-sdc-vdd_io
-				 * tabla2x-slim-CDC_VDDA_RX
-				 * tabla2x-slim-CDC_VDDA_TX
-				 * tabla2x-slim-CDC_VDD_CP
-				 * tabla2x-slim-VDDIO_CDC
-				 */
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-					regulator-always-on;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				/* mipi_dsi.1-dsi1_pll_vdda */
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-				};
-
-				/* msm_otg-HSUSB_3p3 */
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				/* msm_otg-HSUSB_1p8 */
-				l4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				/* msm_sdcc.1-sdc_vdd */
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				/* mipi_dsi.1-dsi1_avdd */
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				/* pwm_power for backlight */
-				l17 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				/* camera, qdsp6 */
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				/*
-				 * tabla2x-slim-CDC_VDDA_A_1P2V
-				 * tabla2x-slim-VDDD_CDC_D
-				 */
-				l25 {
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-				/*
-				 * mipi_dsi.1-dsi1_vddio
-				 * pil_riva-pll_vdd
-				 */
-				lvs7 {
-					bias-pull-down;
-				};
-			};
-		};
-
-		mdp@5100000 {
-			status = "okay";
-			ports {
-				port@1 {
-					mdp_dsi1_out: endpoint {
-						remote-endpoint = <&dsi0_in>;
-					};
-				};
-			};
-		};
-
-		dsi0: mdss_dsi@4700000 {
-			status = "okay";
-			vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
-			vdd-supply = <&pm8921_l8>;
-			vddio-supply = <&pm8921_lvs7>;
-			avdd-supply = <&pm8921_l11>;
-			vcss-supply = <&ext_3p3v>;
-
-			panel@0 {
-				reg = <0>;
-				compatible = "jdi,lt070me05000";
-
-				vddp-supply = <&pm8921_l17>;
-				iovcc-supply = <&pm8921_lvs7>;
-
-				enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
-				reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
-				dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-			ports {
-				port@0 {
-					dsi0_in: endpoint {
-						remote-endpoint = <&mdp_dsi1_out>;
-					};
-				};
-
-				port@1 {
-					dsi0_out: endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
-		};
-
-		dsi-phy@4700200 {
-			status = "okay";
-			vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
-		};
-
-		gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-				status = "okay";
-				clock-frequency = <200000>;
-				pinctrl-0 = <&i2c3_pins>;
-				pinctrl-names = "default";
-
-				trackpad@10 {
-					compatible = "elan,ekth3500";
-					reg = <0x10>;
-					interrupt-parent = <&tlmm_pinmux>;
-					interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
-				};
-			};
-		};
-
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-				pinctrl-0 = <&i2c1_pins>;
-				pinctrl-names = "default";
-
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-
-				bq27541@55 {
-					compatible = "ti,bq27541";
-					reg = <0x55>;
-				};
-
-			};
-		};
-
-		gsbi@16500000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@16540000 {
-				status = "ok";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi6_uart_4pins>;
-			};
-		};
-
-		gsbi@16600000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "ok";
-			};
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-		};
-
-		imem@2a03f000 {
-			compatible = "syscon", "simple-mfd";
-			reg = <0x2a03f000 0x1000>;
-
-			reboot-mode {
-				compatible = "syscon-reboot-mode";
-				offset = <0x65c>;
-
-				mode-normal	= <0x77665501>;
-				mode-bootloader	= <0x77665500>;
-				mode-recovery	= <0x77665502>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
deleted file mode 100644
index 209eb21cea00..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ /dev/null
@@ -1,246 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "CompuLab CM-QS600";
-	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	pwrseq {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		sdcc4_pwrseq: sdcc4_pwrseq {
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_default_gpios>;
-			compatible = "mmc-pwrseq-simple";
-			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
-
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-			};
-		};
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-
-				eeprom@50 {
-					compatible = "atmel,24c02";
-					reg = <0x50>;
-					pagesize = <32>;
-				};
-			};
-		};
-
-		gsbi@16600000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "ok";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "ok";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		/* on board fixed 3.3v supply */
-		v3p3_fixed: v3p3 {
-			compatible = "regulator-fixed";
-			regulator-name = "PCIE V3P3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios {
-						pios {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
-		};
-
-		pci@1b500000 {
-			status = "ok";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&v3p3_fixed>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: sdcc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc3: sdcc@12180000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: sdcc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				vqmmc-supply = <&v3p3_fixed>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
deleted file mode 100644
index 83aaf4a74398..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ /dev/null
@@ -1,381 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Qualcomm APQ8064/IFC6410";
-	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-		serial1 = &gsbi6_serial;
-		i2c0 = &gsbi1_i2c;
-		i2c1 = &gsbi2_i2c;
-		i2c2 = &gsbi3_i2c;
-		i2c3 = &gsbi4_i2c;
-		spi0 = &gsbi5_spi;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	pwrseq {
-		compatible = "simple-bus";
-
-		sdcc4_pwrseq: sdcc4_pwrseq {
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_default_gpios>;
-			compatible = "mmc-pwrseq-simple";
-			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&notify_led>;
-
-		led@1 {
-			label = "apq8064:green:user1";
-			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "d";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&hdmi_out>;
-			};
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
-
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-			};
-		};
-
-		ext_3p3v: regulator-fixed@1 {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-name = "ext_3p3v";
-			regulator-type = "voltage";
-			startup-delay-us = <0>;
-			gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			regulator-boot-on;
-		};
-
-		gsbi3: gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-				status = "okay";
-			};
-		};
-
-		gsbi@16300000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			/* CAM I2C MIPI-CSI connector */
-			i2c@16380000 {
-				status = "okay";
-			};
-		};
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-			};
-		};
-
-		gsbi@1a200000 {
-			qcom,mode = <GSBI_PROT_SPI>;
-			status = "okay";
-			spi4: spi@1a280000 {
-				status = "okay";
-				num-cs = <1>;
-				cs-gpios = <&tlmm_pinmux 53 0>;
-			};
-		};
-
-		gsbi@16500000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_UART_W_FC>;
-
-			serial@16540000 {
-				status = "ok";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi6_uart_4pins>;
-			};
-		};
-
-		gsbi@16600000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "ok";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
-		};
-
-		sata_phy0: phy@1b400000 {
-			status = "okay";
-		};
-
-		sata0: sata@29000000 {
-			status		= "okay";
-			target-supply	= <&pm8921_s4>;
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		pci@1b500000 {
-			status = "ok";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&ext_3p3v>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios {
-						pios {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-
-					notify_led: nled {
-						pios {
-							pins = "gpio18";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: sdcc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc3: sdcc@12180000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l6>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: sdcc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&ext_3p3v>;
-				vqmmc-supply = <&pm8921_lvs1>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
-		};
-
-		hdmi-tx@4a00000 {
-			status = "okay";
-
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-			hdmi-mux-supply = <&ext_3p3v>;
-
-			hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
-
-			ports {
-				port@0 {
-					endpoint {
-						remote-endpoint = <&mdp_dtv_out>;
-					};
-				};
-
-				port@1 {
-					endpoint {
-						remote-endpoint = <&hdmi_con>;
-					};
-				};
-			};
-		};
-
-		hdmi-phy@4a00400 {
-			status = "okay";
-
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-		};
-
-		mdp@5100000 {
-			status = "okay";
-
-			ports {
-				port@3 {
-					endpoint {
-						remote-endpoint = <&hdmi_in>;
-					};
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
deleted file mode 100644
index 8bf488fb86ad..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ /dev/null
@@ -1,402 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z";
-	compatible = "sony,xperia-yuga", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi5_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			gsbi5_uart_pin_a: gsbi5-uart-pin-active {
-				rx {
-					pins = "gpio52";
-					function = "gsbi5";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-
-				tx {
-					pins = "gpio51";
-					function = "gsbi5";
-					drive-strength = <4>;
-					bias-disable;
-				};
-			};
-
-
-			sdcc3_cd_pin_a: sdcc3-cd-pin-active {
-				pins = "gpio26";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-
-		rpm@108000 {
-			regulators {
-				vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs_1_3_6-supply = <&pm8921_s4>;
-				vin_lvs_4_5_7-supply = <&pm8921_s4>;
-				vin_ncp-supply = <&pm8921_l6>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_l24-supply = <&pm8921_s1>;
-				vin_l25-supply = <&pm8921_s1>;
-				vin_l27-supply = <&pm8921_s7>;
-				vin_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s8 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-
-				/* PMOS LDO */
-				l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					bias-pull-down;
-				};
-
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l10 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l17 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				l18 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l21 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l22 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				l27 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-				};
-
-				l28 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l29 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs2 {
-					bias-pull-down;
-				};
-
-				lvs3 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-
-				lvs7 {
-					bias-pull-down;
-				};
-
-				usb-switch {};
-
-				hdmi-switch {};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					gpio_keys_pin_a: gpio-keys-pin-active {
-						pins = "gpio3", "gpio4", "gpio29", "gpio35";
-						function = "normal";
-
-						bias-pull-up;
-						drive-push-pull;
-						input-enable;
-						power-source = <2>;
-						qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-						qcom,pull-up-strength = <0>;
-					};
-				};
-			};
-		};
-
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		gsbi@1a200000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@1a240000 {
-				status = "ok";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi5_uart_pin_a>;
-			};
-		};
-
-		amba {
-			sdcc1: sdcc@12400000 {
-				status = "okay";
-
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			sdcc3: sdcc@12180000 {
-				status = "okay";
-
-				vmmc-supply = <&pm8921_l6>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
-			};
-		};
-
-		riva-pil@3204000 {
-			status = "okay";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
deleted file mode 100644
index 244f04e19c9d..000000000000
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ /dev/null
@@ -1,346 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-
-/ {
-	model = "Qualcomm APQ8074 Dragonboard";
-	compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-		usid0 = &pm8941_0;
-		usid4 = &pm8841_0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		serial@f991e000 {
-			status = "ok";
-		};
-
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "ok";
-
-			vmmc-supply = <&pm8941_l20>;
-			vqmmc-supply = <&pm8941_s3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc1_pin_a>;
-		};
-
-		sdhci@f98a4900 {
-			cd-gpios = <&msmgpio 62 0x1>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-			bus-width = <4>;
-			status = "ok";
-
-			vmmc-supply = <&pm8941_l21>;
-			vqmmc-supply = <&pm8941_l13>;
-		};
-
-		usb@f9a55000 {
-			status = "ok";
-			phys = <&usb_hs2_phy>;
-			phy-select = <&tcsr 0xb000 1>;
-			extcon = <&smbb>, <&usb_id>;
-			vbus-supply = <&chg_otg>;
-			hnp-disable;
-			srp-disable;
-			adp-disable;
-			ulpi {
-				phy@b {
-					status = "ok";
-					v3p3-supply = <&pm8941_l24>;
-					v1p8-supply = <&pm8941_l6>;
-					extcon = <&smbb>;
-					qcom,init-seq = /bits/ 8 <0x1 0x63>;
-				};
-			};
-		};
-
-
-		pinctrl@fd510000 {
-			i2c11_pins: i2c11 {
-				mux {
-					pins = "gpio83", "gpio84";
-					function = "blsp_i2c11";
-				};
-			};
-
-			spi8_default: spi8_default {
-				mosi {
-					pins = "gpio45";
-					function = "blsp_spi8";
-				};
-				miso {
-					pins = "gpio46";
-					function = "blsp_spi8";
-				};
-				cs {
-					pins = "gpio47";
-					function = "blsp_spi8";
-				};
-				clk {
-					pins = "gpio48";
-					function = "blsp_spi8";
-				};
-			};
-
-			sdhc1_pin_a: sdhc1-pin-active {
-				clk {
-					pins = "sdc1_clk";
-					drive-strength = <16>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc1_cmd", "sdc1_data";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-				pins = "gpio62";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			sdhc2_pin_a: sdhc2-pin-active {
-				clk {
-					pins = "sdc2_clk";
-					drive-strength = <10>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc2_cmd", "sdc2_data";
-					drive-strength = <6>;
-					bias-pull-up;
-				};
-			};
-		};
-
-		i2c@f9967000 {
-			status = "okay";
-			clock-frequency = <200000>;
-			pinctrl-0 = <&i2c11_pins>;
-			pinctrl-names = "default";
-
-			eeprom: eeprom@52 {
-				compatible = "atmel,24c128";
-				reg = <0x52>;
-				pagesize = <32>;
-				read-only;
-			};
-		};
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vin_5vs-supply = <&pm8941_5v>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-						regulator-always-on;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
deleted file mode 100644
index e239a0486936..000000000000
--- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
+++ /dev/null
@@ -1,127 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-ipq8064.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
-	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
-
-	aliases {
-		serial0 = &gsbi4_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		gsbi@16300000 {
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			status = "ok";
-
-			serial@16340000 {
-				status = "ok";
-			};
-		};
-
-		gsbi5: gsbi@1a200000 {
-			qcom,mode = <GSBI_PROT_SPI>;
-			status = "ok";
-
-			spi4: spi@1a280000 {
-				status = "ok";
-				spi-max-frequency = <50000000>;
-
-				pinctrl-0 = <&spi_pins>;
-				pinctrl-names = "default";
-
-				cs-gpios = <&qcom_pinmux 20 0>;
-
-				flash: m25p80@0 {
-					compatible = "s25fl256s1";
-					#address-cells = <1>;
-					#size-cells = <1>;
-					spi-max-frequency = <50000000>;
-					reg = <0>;
-
-					partition@0 {
-						label = "rootfs";
-						reg = <0x0 0x1000000>;
-					};
-
-					partition@1 {
-						label = "scratch";
-						reg = <0x1000000 0x1000000>;
-					};
-				};
-			};
-		};
-
-		sata-phy@1b400000 {
-			status = "ok";
-		};
-
-		sata@29000000 {
-			ports-implemented = <0x1>;
-			status = "ok";
-		};
-
-		gpio_keys {
-			compatible = "gpio-keys";
-			pinctrl-0 = <&buttons_pins>;
-			pinctrl-names = "default";
-
-			button@1 {
-				label = "reset";
-				linux,code = <KEY_RESTART>;
-				gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
-				linux,input-type = <1>;
-				debounce-interval = <60>;
-			};
-			button@2 {
-				label = "wps";
-				linux,code = <KEY_WPS_BUTTON>;
-				gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
-				linux,input-type = <1>;
-				debounce-interval = <60>;
-			};
-		};
-
-		leds {
-			compatible = "gpio-leds";
-			pinctrl-0 = <&leds_pins>;
-			pinctrl-names = "default";
-
-			led@7 {
-				label = "led_usb1";
-				gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "usbdev";
-				default-state = "off";
-			};
-
-			led@8 {
-				label = "led_usb3";
-				gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "usbdev";
-				default-state = "off";
-			};
-
-			led@9 {
-				label = "status_led_fail";
-				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-
-			led@26 {
-				label = "sata_led";
-				gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-
-			led@53 {
-				label = "status_led_pass";
-				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
deleted file mode 100644
index 16c0da97932c..000000000000
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ /dev/null
@@ -1,669 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
-#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "Qualcomm IPQ8064";
-	compatible = "qcom,ipq8064";
-	interrupt-parent = <&intc>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v1";
-			device_type = "cpu";
-			reg = <0>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc0>;
-			qcom,saw = <&saw0>;
-		};
-
-		cpu@1 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v1";
-			device_type = "cpu";
-			reg = <1>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc1>;
-			qcom,saw = <&saw1>;
-		};
-
-		L2: l2-cache {
-			compatible = "cache";
-			cache-level = <2>;
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x0>;
-	};
-
-	cpu-pmu {
-		compatible = "qcom,krait-pmu";
-		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
-					  IRQ_TYPE_LEVEL_HIGH)>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		nss@40000000 {
-			reg = <0x40000000 0x1000000>;
-			no-map;
-		};
-
-		smem@41000000 {
-			reg = <0x41000000 0x200000>;
-			no-map;
-		};
-	};
-
-	clocks {
-		cxo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <25000000>;
-		};
-
-		pxo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <25000000>;
-		};
-
-		sleep_clk: sleep_clk {
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-			#clock-cells = <0>;
-		};
-	};
-
-	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		lpass@28100000 {
-			compatible = "qcom,lpass-cpu";
-			status = "disabled";
-			clocks = <&lcc AHBIX_CLK>,
-					<&lcc MI2S_OSR_CLK>,
-					<&lcc MI2S_BIT_CLK>;
-			clock-names = "ahbix-clk",
-					"mi2s-osr-clk",
-					"mi2s-bit-clk";
-			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "lpass-irq-lpaif";
-			reg = <0x28100000 0x10000>;
-			reg-names = "lpass-lpaif";
-		};
-
-		qcom_pinmux: pinmux@800000 {
-			compatible = "qcom,ipq8064-pinctrl";
-			reg = <0x800000 0x4000>;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-
-			pcie0_pins: pcie0_pinmux {
-				mux {
-					pins = "gpio3";
-					function = "pcie1_rst";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-
-			pcie1_pins: pcie1_pinmux {
-				mux {
-					pins = "gpio48";
-					function = "pcie2_rst";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-
-			pcie2_pins: pcie2_pinmux {
-				mux {
-					pins = "gpio63";
-					function = "pcie3_rst";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-
-			spi_pins: spi_pins {
-				mux {
-					pins = "gpio18", "gpio19", "gpio21";
-					function = "gsbi5";
-					drive-strength = <10>;
-					bias-none;
-				};
-			};
-
-			leds_pins: leds_pins {
-				mux {
-					pins = "gpio7", "gpio8", "gpio9",
-					       "gpio26", "gpio53";
-					function = "gpio";
-					drive-strength = <2>;
-					bias-pull-down;
-					output-low;
-				};
-			};
-
-			buttons_pins: buttons_pins {
-				mux {
-					pins = "gpio54";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-			};
-		};
-
-		intc: interrupt-controller@2000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x02000000 0x1000>,
-			      <0x02002000 0x1000>;
-		};
-
-		timer@200a000 {
-			compatible = "qcom,kpss-timer",
-				     "qcom,kpss-wdt-ipq8064", "qcom,msm-timer";
-			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
-						 IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
-						 IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
-						 IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
-						 IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
-						 IRQ_TYPE_EDGE_RISING)>;
-			reg = <0x0200a000 0x100>;
-			clock-frequency = <25000000>,
-					  <32768>;
-			clocks = <&sleep_clk>;
-			clock-names = "sleep";
-			cpu-offset = <0x80000>;
-		};
-
-		acc0: clock-controller@2088000 {
-			compatible = "qcom,kpss-acc-v1";
-			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
-		};
-
-		acc1: clock-controller@2098000 {
-			compatible = "qcom,kpss-acc-v1";
-			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
-		};
-
-		saw0: regulator@2089000 {
-			compatible = "qcom,saw2";
-			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
-		};
-
-		saw1: regulator@2099000 {
-			compatible = "qcom,saw2";
-			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
-		};
-
-		gsbi2: gsbi@12480000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <2>;
-			reg = <0x12480000 0x100>;
-			clocks = <&gcc GSBI2_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			status = "disabled";
-
-			syscon-tcsr = <&tcsr>;
-
-			serial@12490000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x12490000 0x1000>,
-				      <0x12480000 0x1000>;
-				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-
-			i2c@124a0000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				reg = <0x124a0000 0x1000>;
-				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-		};
-
-		gsbi4: gsbi@16300000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <4>;
-			reg = <0x16300000 0x100>;
-			clocks = <&gcc GSBI4_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			status = "disabled";
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi4_serial: serial@16340000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16340000 0x1000>,
-				      <0x16300000 0x1000>;
-				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-
-			i2c@16380000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				reg = <0x16380000 0x1000>;
-				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-		};
-
-		gsbi5: gsbi@1a200000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <5>;
-			reg = <0x1a200000 0x100>;
-			clocks = <&gcc GSBI5_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			status = "disabled";
-
-			syscon-tcsr = <&tcsr>;
-
-			serial@1a240000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x1a240000 0x1000>,
-				      <0x1a200000 0x1000>;
-				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-
-			i2c@1a280000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				reg = <0x1a280000 0x1000>;
-				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-			spi@1a280000 {
-				compatible = "qcom,spi-qup-v1.1.1";
-				reg = <0x1a280000 0x1000>;
-				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-		};
-
-		gsbi7: gsbi@16600000 {
-			status = "disabled";
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <7>;
-			reg = <0x16600000 0x100>;
-			clocks = <&gcc GSBI7_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			syscon-tcsr = <&tcsr>;
-
-			gsbi7_serial: serial@16640000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16640000 0x1000>,
-				      <0x16600000 0x1000>;
-				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		sata_phy: sata-phy@1b400000 {
-			compatible = "qcom,ipq806x-sata-phy";
-			reg = <0x1b400000 0x200>;
-
-			clocks = <&gcc SATA_PHY_CFG_CLK>;
-			clock-names = "cfg";
-
-			#phy-cells = <0>;
-			status = "disabled";
-		};
-
-		sata@29000000 {
-			compatible = "qcom,ipq806x-ahci", "generic-ahci";
-			reg = <0x29000000 0x180>;
-
-			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
-			clocks = <&gcc SFAB_SATA_S_H_CLK>,
-				 <&gcc SATA_H_CLK>,
-				 <&gcc SATA_A_CLK>,
-				 <&gcc SATA_RXOOB_CLK>,
-				 <&gcc SATA_PMALIVE_CLK>;
-			clock-names = "slave_face", "iface", "core",
-					"rxoob", "pmalive";
-
-			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates = <100000000>, <100000000>;
-
-			phys = <&sata_phy>;
-			phy-names = "sata-phy";
-			status = "disabled";
-		};
-
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x00500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-		};
-
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-ipq8064";
-			reg = <0x00900000 0x4000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-ipq8064", "syscon";
-			reg = <0x1a400000 0x100>;
-		};
-
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-ipq8064";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		pcie0: pci@1b500000 {
-			compatible = "qcom,pcie-ipq8064";
-			reg = <0x1b500000 0x1000
-			       0x1b502000 0x80
-			       0x1b600000 0x100
-			       0x0ff00000 0x100000>;
-			reg-names = "dbi", "elbi", "parf", "config";
-			device_type = "pci";
-			linux,pci-domain = <0>;
-			bus-range = <0x00 0xff>;
-			num-lanes = <1>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-
-			ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
-
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "msi";
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
-			clocks = <&gcc PCIE_A_CLK>,
-				 <&gcc PCIE_H_CLK>,
-				 <&gcc PCIE_PHY_CLK>,
-				 <&gcc PCIE_AUX_CLK>,
-				 <&gcc PCIE_ALT_REF_CLK>;
-			clock-names = "core", "iface", "phy", "aux", "ref";
-
-			assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
-			assigned-clock-rates = <100000000>;
-
-			resets = <&gcc PCIE_ACLK_RESET>,
-				 <&gcc PCIE_HCLK_RESET>,
-				 <&gcc PCIE_POR_RESET>,
-				 <&gcc PCIE_PCI_RESET>,
-				 <&gcc PCIE_PHY_RESET>,
-				 <&gcc PCIE_EXT_RESET>;
-			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-
-			pinctrl-0 = <&pcie0_pins>;
-			pinctrl-names = "default";
-
-			status = "disabled";
-			perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
-		};
-
-		pcie1: pci@1b700000 {
-			compatible = "qcom,pcie-ipq8064";
-			reg = <0x1b700000 0x1000
-			       0x1b702000 0x80
-			       0x1b800000 0x100
-			       0x31f00000 0x100000>;
-			reg-names = "dbi", "elbi", "parf", "config";
-			device_type = "pci";
-			linux,pci-domain = <1>;
-			bus-range = <0x00 0xff>;
-			num-lanes = <1>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-
-			ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
-
-			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "msi";
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
-			clocks = <&gcc PCIE_1_A_CLK>,
-				 <&gcc PCIE_1_H_CLK>,
-				 <&gcc PCIE_1_PHY_CLK>,
-				 <&gcc PCIE_1_AUX_CLK>,
-				 <&gcc PCIE_1_ALT_REF_CLK>;
-			clock-names = "core", "iface", "phy", "aux", "ref";
-
-			assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
-			assigned-clock-rates = <100000000>;
-
-			resets = <&gcc PCIE_1_ACLK_RESET>,
-				 <&gcc PCIE_1_HCLK_RESET>,
-				 <&gcc PCIE_1_POR_RESET>,
-				 <&gcc PCIE_1_PCI_RESET>,
-				 <&gcc PCIE_1_PHY_RESET>,
-				 <&gcc PCIE_1_EXT_RESET>;
-			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-
-			pinctrl-0 = <&pcie1_pins>;
-			pinctrl-names = "default";
-
-			status = "disabled";
-			perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
-		};
-
-		pcie2: pci@1b900000 {
-			compatible = "qcom,pcie-ipq8064";
-			reg = <0x1b900000 0x1000
-			       0x1b902000 0x80
-			       0x1ba00000 0x100
-			       0x35f00000 0x100000>;
-			reg-names = "dbi", "elbi", "parf", "config";
-			device_type = "pci";
-			linux,pci-domain = <2>;
-			bus-range = <0x00 0xff>;
-			num-lanes = <1>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-
-			ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
-
-			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "msi";
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
-			clocks = <&gcc PCIE_2_A_CLK>,
-				 <&gcc PCIE_2_H_CLK>,
-				 <&gcc PCIE_2_PHY_CLK>,
-				 <&gcc PCIE_2_AUX_CLK>,
-				 <&gcc PCIE_2_ALT_REF_CLK>;
-			clock-names = "core", "iface", "phy", "aux", "ref";
-
-			assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
-			assigned-clock-rates = <100000000>;
-
-			resets = <&gcc PCIE_2_ACLK_RESET>,
-				 <&gcc PCIE_2_HCLK_RESET>,
-				 <&gcc PCIE_2_POR_RESET>,
-				 <&gcc PCIE_2_PCI_RESET>,
-				 <&gcc PCIE_2_PHY_RESET>,
-				 <&gcc PCIE_2_EXT_RESET>;
-			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-
-			pinctrl-0 = <&pcie2_pins>;
-			pinctrl-names = "default";
-
-			status = "disabled";
-			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
-		};
-
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdcc1bam:dma@12402000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc3bam:dma@12182000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12182000 0x8000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC3_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			sdcc@12400000 {
-				status          = "disabled";
-				compatible      = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg             = <0x12400000 0x2000>;
-				interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names     = "mclk", "apb_pclk";
-				bus-width       = <8>;
-				max-frequency   = <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				mmc-ddr-1_8v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc@12180000 {
-				compatible      = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status          = "disabled";
-				reg             = <0x12180000 0x2000>;
-				interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names     = "mclk", "apb_pclk";
-				bus-width       = <8>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency   = <192000000>;
-				#mmc-ddr-1_8v;
-				sd-uhs-sdr104;
-				sd-uhs-ddr50;
-				vqmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
deleted file mode 100644
index 26b034bd19d2..000000000000
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
+++ /dev/null
@@ -1,171 +0,0 @@
-/*
- * Device Tree Source for Sierra Wireless WP8548 Module
- *
- * Copyright (C) 2016 BayLibre, SAS.
- * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "qcom-mdm9615.dtsi"
-
-/ {
-	model = "Sierra Wireless WP8548 Module";
-	compatible = "swir,wp8548", "qcom,mdm9615";
-
-	memory {
-		device_type = "memory";
-		reg = <0x48000000 0x7F00000>;
-	};
-};
-
-&msmgpio {
-	pinctrl-0 = <&reset_out_pins>;
-	pinctrl-names = "default";
-
-	gsbi3_pins: gsbi3_pins {
-		mux {
-			pins = "gpio8", "gpio9", "gpio10", "gpio11";
-			function = "gsbi3";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	gsbi4_pins: gsbi4_pins {
-		mux {
-			pins = "gpio12", "gpio13", "gpio14", "gpio15";
-			function = "gsbi4";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	gsbi5_i2c_pins: gsbi5_i2c_pins {
-		pin16 {
-			pins = "gpio16";
-			function = "gsbi5_i2c";
-			drive-strength = <8>;
-			bias-disable;
-		};
-
-		pin17 {
-			pins = "gpio17";
-			function = "gsbi5_i2c";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	gsbi5_uart_pins: gsbi5_uart_pins {
-		mux {
-			pins = "gpio18", "gpio19";
-			function = "gsbi5_uart";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	reset_out_pins: reset_out_pins {
-		pins {
-			pins = "gpio66";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-			output-high;
-		};
-	};
-};
-
-&pmicgpio {
-	usb_vbus_5v_pins: usb_vbus_5v_pins {
-		pins = "gpio4";
-		function = "normal";
-		output-high;
-		bias-disable;
-		qcom,drive-strength = <1>;
-		power-source = <2>;
-	};
-};
-
-&gsbi3 {
-	status = "ok";
-	qcom,mode = <GSBI_PROT_SPI>;
-};
-
-&gsbi3_spi {
-	status = "ok";
-	pinctrl-0 = <&gsbi3_pins>;
-	pinctrl-names = "default";
-	assigned-clocks = <&gcc GSBI3_QUP_CLK>;
-	assigned-clock-rates = <24000000>;
-};
-
-&gsbi4 {
-	status = "ok";
-	qcom,mode = <GSBI_PROT_UART_W_FC>;
-};
-
-&gsbi4_serial {
-	status = "ok";
-	pinctrl-0 = <&gsbi4_pins>;
-	pinctrl-names = "default";
-};
-
-&gsbi5 {
-	status = "ok";
-	qcom,mode = <GSBI_PROT_I2C_UART>;
-};
-
-&gsbi5_i2c {
-	status = "ok";
-	clock-frequency = <200000>;
-	pinctrl-0 = <&gsbi5_i2c_pins>;
-	pinctrl-names = "default";
-};
-
-&gsbi5_serial {
-	status = "ok";
-	pinctrl-0 = <&gsbi5_uart_pins>;
-	pinctrl-names = "default";
-};
-
-&sdcc1 {
-	status = "ok";
-};
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
deleted file mode 100644
index 356e9535f7a6..000000000000
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ /dev/null
@@ -1,553 +0,0 @@
-/*
- * Device Tree Source for Qualcomm MDM9615 SoC
- *
- * Copyright (C) 2016 BayLibre, SAS.
- * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-mdm9615.h>
-#include <dt-bindings/reset/qcom,gcc-mdm9615.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "Qualcomm MDM9615";
-	compatible = "qcom,mdm9615";
-	interrupt-parent = <&intc>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a5";
-			device_type = "cpu";
-			next-level-cache = <&L2>;
-		};
-	};
-
-	cpu-pmu {
-		compatible = "arm,cortex-a5-pmu";
-		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
-	};
-
-	clocks {
-		cxo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
-		};
-	};
-
-	regulators {
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
-	};
-
-	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		L2: l2-cache@2040000 {
-			compatible = "arm,pl310-cache";
-			reg = <0x02040000 0x1000>;
-			arm,data-latency = <2 2 0>;
-			cache-unified;
-			cache-level = <2>;
-		};
-
-		intc: interrupt-controller@2000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x02000000 0x1000>,
-			      <0x02002000 0x1000>;
-		};
-
-		timer@200a000 {
-			compatible = "qcom,kpss-timer", "qcom,msm-timer";
-			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>;
-			reg = <0x0200a000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
-			cpu-offset = <0x80000>;
-		};
-
-		msmgpio: pinctrl@800000 {
-			compatible = "qcom,mdm9615-pinctrl";
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			reg = <0x800000 0x4000>;
-		};
-
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-mdm9615";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			reg = <0x900000 0x4000>;
-		};
-
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-mdm9615";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		l2cc: clock-controller@2011000 {
-			compatible = "syscon";
-			reg = <0x02011000 0x1000>;
-		};
-
-		rng@1a500000 {
-			compatible = "qcom,prng";
-			reg = <0x1a500000 0x200>;
-			clocks = <&gcc PRNG_CLK>;
-			clock-names = "core";
-			assigned-clocks = <&gcc PRNG_CLK>;
-			assigned-clock-rates = <32000000>;
-		};
-
-		gsbi2: gsbi@16100000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <2>;
-			reg = <0x16100000 0x100>;
-			clocks = <&gcc GSBI2_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			gsbi2_i2c: i2c@16180000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16180000 0x1000>;
-				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		gsbi3: gsbi@16200000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <3>;
-			reg = <0x16200000 0x100>;
-			clocks = <&gcc GSBI3_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			gsbi3_spi: spi@16280000 {
-				compatible = "qcom,spi-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16280000 0x1000>;
-				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
-				spi-max-frequency = <24000000>;
-
-				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		gsbi4: gsbi@16300000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <4>;
-			reg = <0x16300000 0x100>;
-			clocks = <&gcc GSBI4_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi4_serial: serial@16340000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16340000 0x1000>,
-				      <0x16300000 0x1000>;
-				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		gsbi5: gsbi@16400000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <5>;
-			reg = <0x16400000 0x100>;
-			clocks = <&gcc GSBI5_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi5_i2c: i2c@16480000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16480000 0x1000>;
-				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
-				/* QUP clock is not initialized, set rate */
-				assigned-clocks = <&gcc GSBI5_QUP_CLK>;
-				assigned-clock-rates = <24000000>;
-
-				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-
-			gsbi5_serial: serial@16440000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16440000 0x1000>,
-				      <0x16400000 0x1000>;
-				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-
-			pmicintc: pmic@0 {
-				compatible = "qcom,pm8018", "qcom,pm8921";
-				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pwrkey@1c {
-					compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-						     <51 IRQ_TYPE_EDGE_RISING>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pmicmpp: mpp@50 {
-					compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <24 IRQ_TYPE_NONE>,
-						     <25 IRQ_TYPE_NONE>,
-						     <26 IRQ_TYPE_NONE>,
-						     <27 IRQ_TYPE_NONE>,
-						     <28 IRQ_TYPE_NONE>,
-						     <29 IRQ_TYPE_NONE>;
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pmicgpio: gpio@150 {
-					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pmicgpio 0 0 6>;
-					#gpio-cells = <2>;
-				};
-			};
-		};
-
-		sdcc1bam: dma@12182000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12182000 0x8000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc2bam: dma@12142000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12142000 0x8000>;
-			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC2_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: sdcc@12180000 {
-				status = "disabled";
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg = <0x12180000 0x2000>;
-				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				max-frequency = <48000000>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-				assigned-clocks = <&gcc SDC1_CLK>;
-				assigned-clock-rates = <400000>;
-			};
-
-			sdcc2: sdcc@12140000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x12140000 0x2000>;
-				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <48000000>;
-				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
-				dma-names = "tx", "rx";
-				assigned-clocks = <&gcc SDC2_CLK>;
-				assigned-clock-rates = <400000>;
-			};
-		};
-
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-mdm9615", "syscon";
-			reg = <0x1a400000 0x100>;
-		};
-
-		rpm: rpm@108000 {
-			compatible = "qcom,rpm-mdm9615";
-			reg = <0x108000 0x1000>;
-
-			qcom,ipc = <&l2cc 0x8 2>;
-
-			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
-
-			regulators {
-				compatible = "qcom,rpm-pm8018-regulators";
-
-				vin_lvs1-supply = <&pm8018_s3>;
-
-				vdd_l7-supply = <&pm8018_s4>;
-				vdd_l8-supply = <&pm8018_s3>;
-				vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
-
-				/* Buck SMPS */
-				pm8018_s1: s1 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s2: s2 {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s3: s3 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s4: s4 {
-					regulator-min-microvolt = <2100000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s5: s5 {
-					regulator-always-on;
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* PMOS LDO */
-				pm8018_l2: l2 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8018_l3: l3 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8018_l4: l4 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				pm8018_l5: l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8018_l6: l6 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8018_l7: l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8018_l8: l8 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8018_l9: l9 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				pm8018_l10: l10 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l11: l11 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l12: l12 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l13: l13 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8018_l14: l14 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				pm8018_lvs1: lvs1 {
-					bias-pull-down;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
deleted file mode 100644
index f01a11b18d6a..000000000000
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <dt-bindings/input/input.h>
-
-#include "qcom-msm8660.dtsi"
-
-/ {
-	model = "Qualcomm MSM8660 SURF";
-	compatible = "qcom,msm8660-surf", "qcom,msm8660";
-
-	aliases {
-		serial0 = &gsbi12_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		gsbi@19c00000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@19c40000 {
-				status = "ok";
-			};
-		};
-
-		/* Temporary fixed regulator */
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: sdcc@12400000 {
-				status = "okay";
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-
-			/* External micro SD card */
-			sdcc3: sdcc@12180000 {
-				status = "okay";
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-		};
-	};
-};
-
-&pm8058 {
-	keypad@148 {
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_FN_F1)
-			MATRIX_KEY(0, 1, KEY_UP)
-			MATRIX_KEY(0, 2, KEY_LEFT)
-			MATRIX_KEY(0, 3, KEY_VOLUMEUP)
-			MATRIX_KEY(1, 0, KEY_FN_F2)
-			MATRIX_KEY(1, 1, KEY_RIGHT)
-			MATRIX_KEY(1, 2, KEY_DOWN)
-			MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
-			MATRIX_KEY(2, 3, KEY_ENTER)
-			MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(4, 1, KEY_UP)
-			MATRIX_KEY(4, 2, KEY_LEFT)
-			MATRIX_KEY(4, 3, KEY_HOME)
-			MATRIX_KEY(4, 4, KEY_FN_F3)
-			MATRIX_KEY(5, 0, KEY_CAMERA)
-			MATRIX_KEY(5, 1, KEY_RIGHT)
-			MATRIX_KEY(5, 2, KEY_DOWN)
-			MATRIX_KEY(5, 3, KEY_BACK)
-			MATRIX_KEY(5, 4, KEY_MENU)
-			>;
-		keypad,num-rows = <6>;
-		keypad,num-columns = <5>;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
deleted file mode 100644
index 82d5d8267adf..000000000000
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ /dev/null
@@ -1,354 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <dt-bindings/input/input.h>
-
-#include "qcom-msm8960.dtsi"
-
-/ {
-	model = "Qualcomm MSM8960 CDP";
-	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
-
-	aliases {
-		serial0 = &gsbi5_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		gsbi@16400000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16440000 {
-				status = "ok";
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: sdcc@12400000 {
-				status = "okay";
-			};
-
-			/* External micro SD card */
-			sdcc3: sdcc@12180000 {
-				status = "okay";
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-				vdd_ncp-supply = <&pm8921_l6>;
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l21_l23_l29-supply = <&pm8921_s8>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				pm8921_s1: s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				pm8921_s2: s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8921_s3: s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				pm8921_s4: s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				pm8921_s7: s7 {
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				pm8921_s8: s8 {
-					regulator-always-on;
-					regulator-min-microvolt = <2050000>;
-					regulator-max-microvolt = <2050000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* PMOS LDO */
-				pm8921_l1: l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8921_l2: l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8921_l3: l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				pm8921_l4: l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l5: l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l6: l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l7: l7 {
-					regulator-always-on;
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l8: l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l9: l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l10: l10 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l11: l11 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8921_l12: l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8921_l14: l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l15: l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l16: l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l17: l17 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l18: l18 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					bias-pull-down;
-				};
-
-				pm8921_l21: l21 {
-					regulator-min-microvolt = <1900000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_l22: l22 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <2750000>;
-					bias-pull-down;
-				};
-
-				pm8921_l23: l23 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l24: l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				pm8921_l25: l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				pm8921_lvs1: lvs1 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs2: lvs2 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs3: lvs3 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs4: lvs4 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs5: lvs5 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs7: lvs7 {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		gsbi@16000000 {
-			status = "ok";
-			qcom,mode = <GSBI_PROT_SPI>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi1_default>;
-			spi@16080000 {
-				status = "ok";
-				eth@0 {
-					compatible = "micrel,ks8851";
-					reg = <0>;
-					interrupt-parent = <&msmgpio>;
-					interrupts = <90 8>;
-					spi-max-frequency = <5400000>;
-					vdd-supply = <&ext_l2>;
-					vdd-io-supply = <&pm8921_lvs6>;
-					reset-gpios = <&msmgpio 89 0>;
-				};
-			};
-		};
-
-		pinctrl@800000 {
-			spi1_default: spi1_default {
-				mux {
-					pins = "gpio6", "gpio7", "gpio9";
-					function = "gsbi1";
-				};
-
-				mosi {
-					pins = "gpio6";
-					drive-strength = <12>;
-					bias-disable;
-				};
-
-				miso {
-					pins = "gpio7";
-					drive-strength = <12>;
-					bias-disable;
-				};
-
-				cs {
-					pins = "gpio8";
-					drive-strength = <12>;
-					bias-disable;
-					output-low;
-				};
-
-				clk {
-					pins = "gpio9";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-
-		ext_l2: gpio-regulator@91 {
-			compatible = "regulator-fixed";
-			regulator-name = "ext_l2";
-			gpio = <&msmgpio 91 0>;
-			startup-delay-us = <10000>;
-			enable-active-high;
-		};
-	};
-};
-
-&pmicintc {
-	keypad@148 {
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_VOLUMEUP)
-			MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
-			MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(0, 3, KEY_CAMERA)
-			>;
-		keypad,num-rows = <1>;
-		keypad,num-columns = <5>;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
deleted file mode 100644
index 26160394d717..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
+++ /dev/null
@@ -1,365 +0,0 @@
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-
-/ {
-	model = "Fairphone 2";
-	compatible = "fairphone,fp2", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_CAMERA>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-	};
-
-	vibrator {
-		compatible = "gpio-vibrator";
-		enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
-		vcc-supply = <&pm8941_l18>;
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <2900000>;
-						regulator-max-microvolt = <3350000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-						regulator-allow-set-load;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	serial@f991e000 {
-		status = "ok";
-	};
-
-	pinctrl@fd510000 {
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "ok";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "ok";
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		bus-width = <4>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
-	};
-
-	usb@f9a55000 {
-		status = "ok";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "ok";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	imem@fe805000 {
-		status = "okay";
-
-		reboot-mode {
-			mode-normal	= <0x77665501>;
-			mode-bootloader	= <0x77665500>;
-			mode-recovery	= <0x77665502>;
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio1", "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
deleted file mode 100644
index 3487daf98e81..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ /dev/null
@@ -1,662 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "LGE MSM 8974 HAMMERHEAD";
-	compatible = "lge,hammerhead", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <815000>;
-						regulator-max-microvolt = <900000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-						regulator-allow-set-load;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_regulator_pin>;
-	};
-};
-
-&soc {
-	serial@f991d000 {
-		status = "ok";
-	};
-
-	pinctrl@fd510000 {
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		i2c1_pins: i2c1 {
-			mux {
-				pins = "gpio2", "gpio3";
-				function = "blsp_i2c1";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c3_pins: i2c3 {
-			mux {
-				pins = "gpio10", "gpio11";
-				function = "blsp_i2c3";
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c11_pins: i2c11 {
-			mux {
-				pins = "gpio83", "gpio84";
-				function = "blsp_i2c11";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c12_pins: i2c12 {
-			mux {
-				pins = "gpio87", "gpio88";
-				function = "blsp_i2c12";
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		mpu6515_pin: mpu6515 {
-			irq {
-				pins = "gpio73";
-				function = "gpio";
-				bias-disable;
-				input-enable;
-			};
-		};
-
-		touch_pin: touch {
-			int {
-				pins = "gpio5";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-
-			reset {
-				pins = "gpio8";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-
-		panel_pin: panel {
-			te {
-				pins = "gpio12";
-				function = "mdp_vsync";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "ok";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "ok";
-
-		max-frequency = <100000000>;
-		bus-width = <4>;
-		non-removable;
-		vmmc-supply = <&vreg_wlan>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		bcrmf@1 {
-			compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
-			reg = <1>;
-
-			brcm,drive-strength = <10>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	i2c@f9967000 {
-		status = "ok";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c11_pins>;
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		led-controller@38 {
-			compatible = "ti,lm3630a";
-			status = "ok";
-			reg = <0x38>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			led@0 {
-				reg = <0>;
-				led-sources = <0 1>;
-				label = "lcd-backlight";
-				default-brightness = <200>;
-			};
-		};
-	};
-
-	i2c@f9968000 {
-		status = "ok";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c12_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		mpu6515@68 {
-			compatible = "invensense,mpu6515";
-			reg = <0x68>;
-			interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
-			vddio-supply = <&pm8941_lvs1>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&mpu6515_pin>;
-
-			i2c-gate {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				ak8963@f {
-					compatible = "asahi-kasei,ak8963";
-					reg = <0x0f>;
-					gpios = <&msmgpio 67 0>;
-					vid-supply = <&pm8941_lvs1>;
-					vdd-supply = <&pm8941_l17>;
-				};
-
-				bmp280@76 {
-					compatible = "bosch,bmp280";
-					reg = <0x76>;
-					vdda-supply = <&pm8941_lvs1>;
-					vddd-supply = <&pm8941_l17>;
-				};
-			};
-		};
-	};
-
-	i2c@f9923000 {
-		status = "ok";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c1_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		charger: bq24192@6b {
-			compatible = "ti,bq24192";
-			reg = <0x6b>;
-			interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
-
-			omit-battery-class;
-
-			usb_otg_vbus: usb-otg-vbus { };
-		};
-	};
-
-	i2c@f9924000 {
-		status = "ok";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		synaptics@70 {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x70>;
-
-			interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&touch_pin>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f12@12 {
-				reg = <0x12>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9925000 {
-		status = "ok";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c3_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		avago_apds993@39 {
-			compatible = "avago,apds9930";
-			reg = <0x39>;
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
-			vdd-supply = <&pm8941_l17>;
-			vddio-supply = <&pm8941_lvs1>;
-			led-max-microamp = <100000>;
-			amstaos,proximity-diodes = <0>;
-		};
-	};
-
-	usb@f9a55000 {
-		status = "ok";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-
-		extcon = <&charger>, <&usb_id>;
-		vbus-supply = <&usb_otg_vbus>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "ok";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	mdss@fd900000 {
-		status = "ok";
-
-		mdp@fd900000 {
-			status = "ok";
-		};
-
-		dsi@fd922800 {
-			status = "ok";
-
-			vdda-supply = <&pm8941_l2>;
-			vdd-supply = <&pm8941_lvs3>;
-			vddio-supply = <&pm8941_l12>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
-
-			panel: panel@0 {
-				reg = <0>;
-				compatible = "lg,acx467akm-7";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&panel_pin>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-		};
-
-		dsi-phy@fd922a00 {
-			status = "ok";
-
-			vddio-supply = <&pm8941_l12>;
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_sleep_clk_pin: wl-sleep-clk {
-				pins = "gpio16";
-				function = "func2";
-
-				output-high;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_regulator_pin: wl-reg-active {
-				pins = "gpio17";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			otg {
-				gpio-hog;
-				gpios = <35 GPIO_ACTIVE_HIGH>;
-				output-high;
-				line-name = "otg-gpio";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
deleted file mode 100644
index eaa1001d0a46..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ /dev/null
@@ -1,24 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-
-/ {
-	model = "Samsung Galaxy S5";
-	compatible = "samsung,klte", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&soc {
-	serial@f991e000 {
-		status = "ok";
-	};
-
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
deleted file mode 100644
index 5669f5f58a86..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
+++ /dev/null
@@ -1,436 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z1 Compact";
-	compatible = "sony,xperia-amami", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	memory@0 {
-		reg = <0 0x40000000>, <0x40000000 0x40000000>;
-		device_type = "memory";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "ok";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "ok";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "ok";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-	};
-
-	dma-controller@f9944000 {
-		qcom,controlled-remotely;
-	};
-
-	usb@f9a55000 {
-		status = "ok";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "ok";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1300000>;
-			qcom,fast-charge-current-limit = <1300000>;
-			qcom,dc-current-limit = <1300000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio4", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-
-		coincell@2800 {
-			status = "ok";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-
-	pm8941@1 {
-		wled@d800 {
-			status = "ok";
-
-			qcom,cs-out;
-			qcom,current-limit = <20>;
-			qcom,current-boost-limit = <805>;
-			qcom,switching-freq = <1600>;
-			qcom,ovp = <29>;
-			qcom,num-strings = <2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
deleted file mode 100644
index 701b396719c7..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
+++ /dev/null
@@ -1,643 +0,0 @@
-#include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z2 Tablet";
-	compatible = "sony,xperia-castor", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-
-						regulator-system-load = <154000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-allow-set-load;
-						regulator-system-load = <500000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-
-	vreg_bl_vddio: lcd-backlight-vddio {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_bl_vddio";
-		regulator-min-microvolt = <3150000>;
-		regulator-max-microvolt = <3150000>;
-
-		gpio = <&msmgpio 69 0>;
-		enable-active-high;
-
-		vin-supply = <&pm8941_s3>;
-		startup-delay-us = <70000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_backlight_en_pin_a>;
-	};
-
-	vreg_vsp: lcd-dcdc-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_vsp";
-		regulator-min-microvolt = <5600000>;
-		regulator-max-microvolt = <5600000>;
-
-		gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_regulator_pin>;
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "ok";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f9864900 {
-		status = "ok";
-
-		max-frequency = <100000000>;
-		non-removable;
-		vmmc-supply = <&vreg_wlan>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc3_pin_a>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		bcrmf@1 {
-			compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
-			reg = <1>;
-
-			brcm,drive-strength = <10>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin>;
-		};
-	};
-
-	sdhci@f98a4900 {
-		status = "ok";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "ok";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-	usb@f9a55000 {
-		status = "ok";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "ok";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c8_pins: i2c8 {
-			mux {
-				pins = "gpio47", "gpio48";
-				function = "blsp_i2c8";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c11_pins: i2c11 {
-			mux {
-				pins = "gpio83", "gpio84";
-				function = "blsp_i2c11";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		lcd_backlight_en_pin_a: lcd-backlight-vddio {
-			pins = "gpio69";
-			drive-strength = <10>;
-			output-low;
-			bias-disable;
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc3_pin_a: sdhc3-pin-active {
-			clk {
-				pins = "gpio40";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd {
-				pins = "gpio39";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-
-			data {
-				pins = "gpio35", "gpio36", "gpio37", "gpio38";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		ts_int_pin: synaptics {
-			pin {
-				pins = "gpio86";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-		};
-	};
-
-	i2c@f9964000 {
-		status = "ok";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c8_pins>;
-
-		synaptics@2c {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x2c>;
-
-			interrupt-parent = <&msmgpio>;
-			interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&ts_int_pin>;
-
-			syna,startup-delay-ms = <10>;
-
-			rmi-f01@1 {
-				reg = <0x1>;
-				syna,nosleep = <1>;
-			};
-
-			rmi-f11@11 {
-				reg = <0x11>;
-				syna,f11-flip-x = <1>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9967000 {
-		status = "ok";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c11_pins>;
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		lp8566_wled: backlight@2c {
-			compatible = "ti,lp8556";
-			reg = <0x2c>;
-			power-supply = <&vreg_bl_vddio>;
-
-			bl-name = "backlight";
-			dev-ctrl = /bits/ 8 <0x05>;
-			init-brt = /bits/ 8 <0x3f>;
-			rom_a0h {
-				rom-addr = /bits/ 8 <0xa0>;
-				rom-val = /bits/ 8 <0xff>;
-			};
-			rom_a1h {
-				rom-addr = /bits/ 8 <0xa1>;
-				rom-val = /bits/ 8 <0x3f>;
-			};
-			rom_a2h {
-				rom-addr = /bits/ 8 <0xa2>;
-				rom-val = /bits/ 8 <0x20>;
-			};
-			rom_a3h {
-				rom-addr = /bits/ 8 <0xa3>;
-				rom-val = /bits/ 8 <0x5e>;
-			};
-			rom_a4h {
-				rom-addr = /bits/ 8 <0xa4>;
-				rom-val = /bits/ 8 <0x02>;
-			};
-			rom_a5h {
-				rom-addr = /bits/ 8 <0xa5>;
-				rom-val = /bits/ 8 <0x04>;
-			};
-			rom_a6h {
-				rom-addr = /bits/ 8 <0xa6>;
-				rom-val = /bits/ 8 <0x80>;
-			};
-			rom_a7h {
-				rom-addr = /bits/ 8 <0xa7>;
-				rom-val = /bits/ 8 <0xf7>;
-			};
-			rom_a9h {
-				rom-addr = /bits/ 8 <0xa9>;
-				rom-val = /bits/ 8 <0x80>;
-			};
-			rom_aah {
-				rom-addr = /bits/ 8 <0xaa>;
-				rom-val = /bits/ 8 <0x0f>;
-			};
-			rom_aeh {
-				rom-addr = /bits/ 8 <0xae>;
-				rom-val = /bits/ 8 <0x0f>;
-			};
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1500000>;
-			qcom,fast-charge-current-limit = <1500000>;
-			qcom,dc-current-limit = <1800000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_sleep_clk_pin: wl-sleep-clk {
-				pins = "gpio17";
-				function = "func2";
-
-				output-high;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_regulator_pin: wl-reg-active {
-				pins = "gpio18";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			lcd_dcdc_en_pin_a: lcd-dcdc-en-active {
-				pins = "gpio20";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-				input-disable;
-				output-low;
-			};
-
-		};
-
-		coincell@2800 {
-			status = "ok";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
deleted file mode 100644
index 450b8321e0a6..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ /dev/null
@@ -1,460 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z1";
-	compatible = "sony,xperia-honami", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	memory@0 {
-		reg = <0 0x40000000>, <0x40000000 0x40000000>;
-		device_type = "memory";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "ok";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "ok";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "ok";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-	i2c@f9924000 {
-		status = "ok";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		synaptics@2c {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x2c>;
-
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&ts_int_pin>;
-
-			syna,startup-delay-ms = <10>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f11@11 {
-				reg = <0x11>;
-				touchscreen-inverted-x;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		ts_int_pin: touch-int {
-			pin {
-				pins = "gpio61";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-		};
-	};
-
-	dma-controller@f9944000 {
-		qcom,controlled-remotely;
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1500000>;
-			qcom,fast-charge-current-limit = <1500000>;
-			qcom,dc-current-limit = <1800000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio4", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-
-		coincell@2800 {
-			status = "ok";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-
-	pm8941@1 {
-		wled@d800 {
-			status = "ok";
-
-			qcom,cs-out;
-			qcom,current-limit = <20>;
-			qcom,current-boost-limit = <805>;
-			qcom,switching-freq = <1600>;
-			qcom,ovp = <29>;
-			qcom,num-strings = <2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
deleted file mode 100644
index 9a84eb0cbbe6..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ /dev/null
@@ -1,1434 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-msm8974.h>
-#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
-#include <dt-bindings/clock/qcom,rpmcc.h>
-#include <dt-bindings/reset/qcom,gcc-msm8974.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "Qualcomm MSM8974";
-	compatible = "qcom,msm8974";
-	interrupt-parent = <&intc>;
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		mpss@8000000 {
-			reg = <0x08000000 0x5100000>;
-			no-map;
-		};
-
-		mba@d100000 {
-			reg = <0x0d100000 0x100000>;
-			no-map;
-		};
-
-		reserved@d200000 {
-			reg = <0x0d200000 0xa00000>;
-			no-map;
-		};
-
-		adsp_region: adsp@dc00000 {
-			reg = <0x0dc00000 0x1900000>;
-			no-map;
-		};
-
-		venus@f500000 {
-			reg = <0x0f500000 0x500000>;
-			no-map;
-		};
-
-		smem_region: smem@fa00000 {
-			reg = <0xfa00000 0x200000>;
-			no-map;
-		};
-
-		tz@fc00000 {
-			reg = <0x0fc00000 0x160000>;
-			no-map;
-		};
-
-		rfsa@fd60000 {
-			reg = <0x0fd60000 0x20000>;
-			no-map;
-		};
-
-		rmtfs@fd80000 {
-			reg = <0x0fd80000 0x180000>;
-			no-map;
-		};
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <GIC_PPI 9 0xf04>;
-
-		CPU0: cpu@0 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v2";
-			device_type = "cpu";
-			reg = <0>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc0>;
-			qcom,saw = <&saw0>;
-			cpu-idle-states = <&CPU_SPC>;
-		};
-
-		CPU1: cpu@1 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v2";
-			device_type = "cpu";
-			reg = <1>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc1>;
-			qcom,saw = <&saw1>;
-			cpu-idle-states = <&CPU_SPC>;
-		};
-
-		CPU2: cpu@2 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v2";
-			device_type = "cpu";
-			reg = <2>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc2>;
-			qcom,saw = <&saw2>;
-			cpu-idle-states = <&CPU_SPC>;
-		};
-
-		CPU3: cpu@3 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v2";
-			device_type = "cpu";
-			reg = <3>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc3>;
-			qcom,saw = <&saw3>;
-			cpu-idle-states = <&CPU_SPC>;
-		};
-
-		L2: l2-cache {
-			compatible = "cache";
-			cache-level = <2>;
-			qcom,saw = <&saw_l2>;
-		};
-
-		idle-states {
-			CPU_SPC: spc {
-				compatible = "qcom,idle-state-spc",
-						"arm,idle-state";
-				entry-latency-us = <150>;
-				exit-latency-us = <200>;
-				min-residency-us = <2000>;
-			};
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x0>;
-	};
-
-	thermal-zones {
-		cpu-thermal0 {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 5>;
-
-			trips {
-				cpu_alert0: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit0: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu-thermal1 {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 6>;
-
-			trips {
-				cpu_alert1: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit1: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu-thermal2 {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 7>;
-
-			trips {
-				cpu_alert2: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit2: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu-thermal3 {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 8>;
-
-			trips {
-				cpu_alert3: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit3: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		q6-dsp-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 1>;
-
-			trips {
-				q6_dsp_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
-		};
-
-		modemtx-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 2>;
-
-			trips {
-				modemtx_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
-		};
-
-		video-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 3>;
-
-			trips {
-				video_alert0: trip-point0 {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
-		};
-
-		wlan-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 4>;
-
-			trips {
-				wlan_alert0: trip-point0 {
-					temperature = <105000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
-		};
-
-		gpu-thermal-top {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 9>;
-
-			trips {
-				gpu1_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
-		};
-
-		gpu-thermal-bottom {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 10>;
-
-			trips {
-				gpu2_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
-		};
-	};
-
-	cpu-pmu {
-		compatible = "qcom,krait-pmu";
-		interrupts = <GIC_PPI 7 0xf04>;
-	};
-
-	clocks {
-		xo_board: xo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
-		};
-
-		sleep_clk: sleep_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 2 0xf08>,
-			     <GIC_PPI 3 0xf08>,
-			     <GIC_PPI 4 0xf08>,
-			     <GIC_PPI 1 0xf08>;
-		clock-frequency = <19200000>;
-	};
-
-	adsp-pil {
-		compatible = "qcom,msm8974-adsp-pil";
-
-		interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-		interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
-
-		cx-supply = <&pm8841_s2>;
-
-		clocks = <&xo_board>;
-		clock-names = "xo";
-
-		memory-region = <&adsp_region>;
-
-		qcom,smem-states = <&adsp_smp2p_out 0>;
-		qcom,smem-state-names = "stop";
-	};
-
-	smem {
-		compatible = "qcom,smem";
-
-		memory-region = <&smem_region>;
-		qcom,rpm-msg-ram = <&rpm_msg_ram>;
-
-		hwlocks = <&tcsr_mutex 3>;
-	};
-
-	smp2p-adsp {
-		compatible = "qcom,smp2p";
-		qcom,smem = <443>, <429>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
-
-		qcom,ipc = <&apcs 8 10>;
-
-		qcom,local-pid = <0>;
-		qcom,remote-pid = <2>;
-
-		adsp_smp2p_out: master-kernel {
-			qcom,entry-name = "master-kernel";
-			#qcom,smem-state-cells = <1>;
-		};
-
-		adsp_smp2p_in: slave-kernel {
-			qcom,entry-name = "slave-kernel";
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	smp2p-modem {
-		compatible = "qcom,smp2p";
-		qcom,smem = <435>, <428>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
-
-		qcom,ipc = <&apcs 8 14>;
-
-		qcom,local-pid = <0>;
-		qcom,remote-pid = <1>;
-
-		modem_smp2p_out: master-kernel {
-			qcom,entry-name = "master-kernel";
-			#qcom,smem-state-cells = <1>;
-		};
-
-		modem_smp2p_in: slave-kernel {
-			qcom,entry-name = "slave-kernel";
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	smp2p-wcnss {
-		compatible = "qcom,smp2p";
-		qcom,smem = <451>, <431>;
-
-		interrupt-parent = <&intc>;
-		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
-
-		qcom,ipc = <&apcs 8 18>;
-
-		qcom,local-pid = <0>;
-		qcom,remote-pid = <4>;
-
-		wcnss_smp2p_out: master-kernel {
-			qcom,entry-name = "master-kernel";
-
-			#qcom,smem-state-cells = <1>;
-		};
-
-		wcnss_smp2p_in: slave-kernel {
-			qcom,entry-name = "slave-kernel";
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	smsm {
-		compatible = "qcom,smsm";
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		qcom,ipc-1 = <&apcs 8 13>;
-		qcom,ipc-2 = <&apcs 8 9>;
-		qcom,ipc-3 = <&apcs 8 19>;
-
-		apps_smsm: apps@0 {
-			reg = <0>;
-
-			#qcom,smem-state-cells = <1>;
-		};
-
-		modem_smsm: modem@1 {
-			reg = <1>;
-			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		adsp_smsm: adsp@2 {
-			reg = <2>;
-			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		wcnss_smsm: wcnss@7 {
-			reg = <7>;
-			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
-
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	firmware {
-		scm {
-			compatible = "qcom,scm";
-			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
-			clock-names = "core", "bus", "iface";
-		};
-	};
-
-	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		intc: interrupt-controller@f9000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0xf9000000 0x1000>,
-			      <0xf9002000 0x1000>;
-		};
-
-		apcs: syscon@f9011000 {
-			compatible = "syscon";
-			reg = <0xf9011000 0x1000>;
-		};
-
-		qfprom: qfprom@fc4bc000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
-			tsens_calib: calib@d0 {
-				reg = <0xd0 0x18>;
-			};
-			tsens_backup: backup@440 {
-				reg = <0x440 0x10>;
-			};
-		};
-
-		tsens: thermal-sensor@fc4a9000 {
-			compatible = "qcom,msm8974-tsens";
-			reg = <0xfc4a9000 0x1000>, /* TM */
-			      <0xfc4a8000 0x1000>; /* SROT */
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
-			#qcom,sensors = <11>;
-			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
-			#thermal-sensor-cells = <1>;
-		};
-
-		timer@f9020000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			compatible = "arm,armv7-timer-mem";
-			reg = <0xf9020000 0x1000>;
-			clock-frequency = <19200000>;
-
-			frame@f9021000 {
-				frame-number = <0>;
-				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9021000 0x1000>,
-				      <0xf9022000 0x1000>;
-			};
-
-			frame@f9023000 {
-				frame-number = <1>;
-				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9023000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9024000 {
-				frame-number = <2>;
-				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9024000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9025000 {
-				frame-number = <3>;
-				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9025000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9026000 {
-				frame-number = <4>;
-				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9026000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9027000 {
-				frame-number = <5>;
-				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9027000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9028000 {
-				frame-number = <6>;
-				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9028000 0x1000>;
-				status = "disabled";
-			};
-		};
-
-		saw0: power-controller@f9089000 {
-			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
-		};
-
-		saw1: power-controller@f9099000 {
-			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
-		};
-
-		saw2: power-controller@f90a9000 {
-			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
-		};
-
-		saw3: power-controller@f90b9000 {
-			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
-		};
-
-		saw_l2: power-controller@f9012000 {
-			compatible = "qcom,saw2";
-			reg = <0xf9012000 0x1000>;
-			regulator;
-		};
-
-		acc0: clock-controller@f9088000 {
-			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
-		};
-
-		acc1: clock-controller@f9098000 {
-			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
-		};
-
-		acc2: clock-controller@f90a8000 {
-			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
-		};
-
-		acc3: clock-controller@f90b8000 {
-			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
-		};
-
-		restart@fc4ab000 {
-			compatible = "qcom,pshold";
-			reg = <0xfc4ab000 0x4>;
-		};
-
-		gcc: clock-controller@fc400000 {
-			compatible = "qcom,gcc-msm8974";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-			reg = <0xfc400000 0x4000>;
-		};
-
-		tcsr: syscon@fd4a0000 {
-			compatible = "syscon";
-			reg = <0xfd4a0000 0x10000>;
-		};
-
-		tcsr_mutex_block: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
-
-		mmcc: clock-controller@fd8c0000 {
-			compatible = "qcom,mmcc-msm8974";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-			reg = <0xfd8c0000 0x6000>;
-		};
-
-		tcsr_mutex: tcsr-mutex {
-			compatible = "qcom,tcsr-mutex";
-			syscon = <&tcsr_mutex_block 0 0x80>;
-
-			#hwlock-cells = <1>;
-		};
-
-		rpm_msg_ram: memory@fc428000 {
-			compatible = "qcom,rpm-msg-ram";
-			reg = <0xfc428000 0x4000>;
-		};
-
-		blsp1_uart1: serial@f991d000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0xf991d000 0x1000>;
-			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			status = "disabled";
-		};
-
-		blsp1_uart2: serial@f991e000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0xf991e000 0x1000>;
-			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			status = "disabled";
-		};
-
-		sdhci@f9824900 {
-			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
-			status = "disabled";
-		};
-
-		sdhci@f9864900 {
-			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC3_APPS_CLK>,
-				 <&gcc GCC_SDCC3_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
-			status = "disabled";
-		};
-
-		sdhci@f98a4900 {
-			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
-			status = "disabled";
-		};
-
-		otg: usb@f9a55000 {
-			compatible = "qcom,ci-hdrc";
-			reg = <0xf9a55000 0x200>,
-			      <0xf9a55200 0x200>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
-				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
-			clock-names = "iface", "core";
-			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
-			assigned-clock-rates = <75000000>;
-			resets = <&gcc GCC_USB_HS_BCR>;
-			reset-names = "core";
-			phy_type = "ulpi";
-			dr_mode = "otg";
-			ahb-burst-config = <0>;
-			phy-names = "usb-phy";
-			status = "disabled";
-			#reset-cells = <1>;
-
-			ulpi {
-				usb_hs1_phy: phy@a {
-					compatible = "qcom,usb-hs-phy-msm8974",
-						     "qcom,usb-hs-phy";
-					#phy-cells = <0>;
-					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
-					clock-names = "ref", "sleep";
-					resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
-					reset-names = "phy", "por";
-					status = "disabled";
-				};
-
-				usb_hs2_phy: phy@b {
-					compatible = "qcom,usb-hs-phy-msm8974",
-						     "qcom,usb-hs-phy";
-					#phy-cells = <0>;
-					clocks = <&xo_board>, <&gcc GCC_USB2B_PHY_SLEEP_CLK>;
-					clock-names = "ref", "sleep";
-					resets = <&gcc GCC_USB2B_PHY_BCR>, <&otg 1>;
-					reset-names = "phy", "por";
-					status = "disabled";
-				};
-			};
-		};
-
-		rng@f9bff000 {
-			compatible = "qcom,prng";
-			reg = <0xf9bff000 0x200>;
-			clocks = <&gcc GCC_PRNG_AHB_CLK>;
-			clock-names = "core";
-		};
-
-		msmgpio: pinctrl@fd510000 {
-			compatible = "qcom,msm8974-pinctrl";
-			reg = <0xfd510000 0x4000>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		i2c@f9923000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9923000 0x1000>;
-			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c@f9924000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9924000 0x1000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c3: i2c@f9925000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9925000 0x1000>;
-			interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c8: i2c@f9964000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9964000 0x1000>;
-			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c11: i2c@f9967000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9967000 0x1000>;
-			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
-			dma-names = "tx", "rx";
-		};
-
-		blsp_i2c12: i2c@f9968000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9968000 0x1000>;
-			interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		spmi_bus: spmi@fc4cf000 {
-			compatible = "qcom,spmi-pmic-arb";
-			reg-names = "core", "intr", "cnfg";
-			reg = <0xfc4cf000 0x1000>,
-			      <0xfc4cb000 0x1000>,
-			      <0xfc4ca000 0x1000>;
-			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,ee = <0>;
-			qcom,channel = <0>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-			interrupt-controller;
-			#interrupt-cells = <4>;
-		};
-
-		blsp2_dma: dma-controller@f9944000 {
-			compatible = "qcom,bam-v1.4.0";
-			reg = <0xf9944000 0x19000>;
-			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		etr@fc322000 {
-			compatible = "arm,coresight-tmc", "arm,primecell";
-			reg = <0xfc322000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			in-ports {
-				port {
-					etr_in: endpoint {
-						remote-endpoint = <&replicator_out0>;
-					};
-				};
-			};
-		};
-
-		tpiu@fc318000 {
-			compatible = "arm,coresight-tpiu", "arm,primecell";
-			reg = <0xfc318000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			in-ports {
-				port {
-					tpiu_in: endpoint {
-						remote-endpoint = <&replicator_out1>;
-					};
-				 };
-			};
-		};
-
-		replicator@fc31c000 {
-			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
-			reg = <0xfc31c000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			out-ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					replicator_out0: endpoint {
-						remote-endpoint = <&etr_in>;
-					};
-				};
-				port@1 {
-					reg = <1>;
-					replicator_out1: endpoint {
-						remote-endpoint = <&tpiu_in>;
-					};
-				};
-			};
-
-			in-ports {
-				port {
-					replicator_in: endpoint {
-						remote-endpoint = <&etf_out>;
-					};
-				};
-			};
-		};
-
-		etf@fc307000 {
-			compatible = "arm,coresight-tmc", "arm,primecell";
-			reg = <0xfc307000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			out-ports {
-				port {
-					etf_out: endpoint {
-						remote-endpoint = <&replicator_in>;
-					};
-				};
-			};
-
-			in-ports {
-				port {
-					etf_in: endpoint {
-						remote-endpoint = <&merger_out>;
-					};
-				};
-			};
-		};
-
-		funnel@fc31b000 {
-			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
-			reg = <0xfc31b000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			in-ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				/*
-				 * Not described input ports:
-				 * 0 - connected trought funnel to Audio, Modem and
-				 *     Resource and Power Manager CPU's
-				 * 2...7 - not-connected
-				 */
-				port@1 {
-					reg = <1>;
-					merger_in1: endpoint {
-						remote-endpoint = <&funnel1_out>;
-					};
-				};
-			};
-
-			out-ports {
-				port {
-					merger_out: endpoint {
-						remote-endpoint = <&etf_in>;
-					};
-				};
-			};
-		};
-
-		funnel@fc31a000 {
-			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
-			reg = <0xfc31a000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			in-ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				/*
-				 * Not described input ports:
-				 * 0 - not-connected
-				 * 1 - connected trought funnel to Multimedia CPU
-				 * 2 - connected to Wireless CPU
-				 * 3 - not-connected
-				 * 4 - not-connected
-				 * 6 - not-connected
-				 * 7 - connected to STM
-				 */
-				port@5 {
-					reg = <5>;
-					funnel1_in5: endpoint {
-						remote-endpoint = <&kpss_out>;
-					};
-				};
-			};
-
-			out-ports {
-				port {
-					funnel1_out: endpoint {
-						remote-endpoint = <&merger_in1>;
-					};
-				};
-			};
-		};
-
-		funnel@fc345000 { /* KPSS funnel only 4 inputs are used */
-			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
-			reg = <0xfc345000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			in-ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					kpss_in0: endpoint {
-						remote-endpoint = <&etm0_out>;
-					};
-				};
-				port@1 {
-					reg = <1>;
-					kpss_in1: endpoint {
-						remote-endpoint = <&etm1_out>;
-					};
-				};
-				port@2 {
-					reg = <2>;
-					kpss_in2: endpoint {
-						remote-endpoint = <&etm2_out>;
-					};
-				};
-				port@3 {
-					reg = <3>;
-					kpss_in3: endpoint {
-						remote-endpoint = <&etm3_out>;
-					};
-				};
-			};
-
-			out-ports {
-				port {
-					kpss_out: endpoint {
-						remote-endpoint = <&funnel1_in5>;
-					};
-				};
-			};
-		};
-
-		etm@fc33c000 {
-			compatible = "arm,coresight-etm4x", "arm,primecell";
-			reg = <0xfc33c000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			cpu = <&CPU0>;
-
-			out-ports {
-				port {
-					etm0_out: endpoint {
-						remote-endpoint = <&kpss_in0>;
-					};
-				};
-			};
-		};
-
-		etm@fc33d000 {
-			compatible = "arm,coresight-etm4x", "arm,primecell";
-			reg = <0xfc33d000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			cpu = <&CPU1>;
-
-			out-ports {
-				port {
-					etm1_out: endpoint {
-						remote-endpoint = <&kpss_in1>;
-					};
-				};
-			};
-		};
-
-		etm@fc33e000 {
-			compatible = "arm,coresight-etm4x", "arm,primecell";
-			reg = <0xfc33e000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			cpu = <&CPU2>;
-
-			out-ports {
-				port {
-					etm2_out: endpoint {
-						remote-endpoint = <&kpss_in2>;
-					};
-				};
-			};
-		};
-
-		etm@fc33f000 {
-			compatible = "arm,coresight-etm4x", "arm,primecell";
-			reg = <0xfc33f000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
-
-			cpu = <&CPU3>;
-
-			out-ports {
-				port {
-					etm3_out: endpoint {
-						remote-endpoint = <&kpss_in3>;
-					};
-				};
-			};
-		};
-
-		mdss: mdss@fd900000 {
-			status = "disabled";
-
-			compatible = "qcom,mdss";
-			reg = <0xfd900000 0x100>,
-			      <0xfd924000 0x1000>;
-			reg-names = "mdss_phys",
-			            "vbif_phys";
-
-			power-domains = <&mmcc MDSS_GDSC>;
-
-			clocks = <&mmcc MDSS_AHB_CLK>,
-			         <&mmcc MDSS_AXI_CLK>,
-			         <&mmcc MDSS_VSYNC_CLK>;
-			clock-names = "iface",
-			              "bus",
-			              "vsync";
-
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-
-			interrupt-controller;
-			#interrupt-cells = <1>;
-
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			mdp: mdp@fd900000 {
-				status = "disabled";
-
-				compatible = "qcom,mdp5";
-				reg = <0xfd900100 0x22000>;
-				reg-names = "mdp_phys";
-
-				interrupt-parent = <&mdss>;
-				interrupts = <0 0>;
-
-				clocks = <&mmcc MDSS_AHB_CLK>,
-					 <&mmcc MDSS_AXI_CLK>,
-					 <&mmcc MDSS_MDP_CLK>,
-					 <&mmcc MDSS_VSYNC_CLK>;
-				clock-names = "iface",
-				              "bus",
-				              "core",
-				              "vsync";
-
-				ports {
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					port@0 {
-						reg = <0>;
-						mdp5_intf1_out: endpoint {
-							remote-endpoint = <&dsi0_in>;
-						};
-					};
-				};
-			};
-
-			dsi0: dsi@fd922800 {
-				status = "disabled";
-
-				compatible = "qcom,mdss-dsi-ctrl";
-				reg = <0xfd922800 0x1f8>;
-				reg-names = "dsi_ctrl";
-
-				interrupt-parent = <&mdss>;
-				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
-
-				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
-				                  <&mmcc PCLK0_CLK_SRC>;
-				assigned-clock-parents = <&dsi_phy0 0>,
-				                         <&dsi_phy0 1>;
-
-				clocks = <&mmcc MDSS_MDP_CLK>,
-				         <&mmcc MDSS_AHB_CLK>,
-				         <&mmcc MDSS_AXI_CLK>,
-				         <&mmcc MDSS_BYTE0_CLK>,
-				         <&mmcc MDSS_PCLK0_CLK>,
-				         <&mmcc MDSS_ESC0_CLK>,
-				         <&mmcc MMSS_MISC_AHB_CLK>;
-				clock-names = "mdp_core",
-				              "iface",
-				              "bus",
-				              "byte",
-				              "pixel",
-				              "core",
-				              "core_mmss";
-
-				phys = <&dsi_phy0>;
-				phy-names = "dsi-phy";
-
-				ports {
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					port@0 {
-						reg = <0>;
-						dsi0_in: endpoint {
-							remote-endpoint = <&mdp5_intf1_out>;
-						};
-					};
-
-					port@1 {
-						reg = <1>;
-						dsi0_out: endpoint {
-						};
-					};
-				};
-			};
-
-			dsi_phy0: dsi-phy@fd922a00 {
-				status = "disabled";
-
-				compatible = "qcom,dsi-phy-28nm-hpm";
-				reg = <0xfd922a00 0xd4>,
-				      <0xfd922b00 0x280>,
-				      <0xfd922d80 0x30>;
-				reg-names = "dsi_pll",
-				            "dsi_phy",
-				            "dsi_phy_regulator";
-
-				#clock-cells = <1>;
-				#phy-cells = <0>;
-				qcom,dsi-phy-index = <0>;
-
-				clocks = <&mmcc MDSS_AHB_CLK>;
-				clock-names = "iface";
-			};
-		};
-
-		imem@fe805000 {
-			status = "disabled";
-			compatible = "syscon", "simple-mfd";
-			reg = <0xfe805000 0x1000>;
-
-			reboot-mode {
-				compatible = "syscon-reboot-mode";
-				offset = <0x65c>;
-			};
-		};
-	};
-
-	smd {
-		compatible = "qcom,smd";
-
-		adsp {
-			interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&apcs 8 8>;
-			qcom,smd-edge = <1>;
-		};
-
-		modem {
-			interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&apcs 8 12>;
-			qcom,smd-edge = <0>;
-		};
-
-		rpm {
-			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
-			qcom,smd-edge = <15>;
-
-			rpm_requests {
-				compatible = "qcom,rpm-msm8974";
-				qcom,smd-channels = "rpm_requests";
-
-				rpmcc: clock-controller {
-					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
-					#clock-cells = <1>;
-				};
-
-				pm8841-regulators {
-					compatible = "qcom,rpm-pm8841-regulators";
-
-					pm8841_s1: s1 {};
-					pm8841_s2: s2 {};
-					pm8841_s3: s3 {};
-					pm8841_s4: s4 {};
-					pm8841_s5: s5 {};
-					pm8841_s6: s6 {};
-					pm8841_s7: s7 {};
-					pm8841_s8: s8 {};
-				};
-
-				pm8941-regulators {
-					compatible = "qcom,rpm-pm8941-regulators";
-
-					pm8941_s1: s1 {};
-					pm8941_s2: s2 {};
-					pm8941_s3: s3 {};
-
-					pm8941_l1: l1 {};
-					pm8941_l2: l2 {};
-					pm8941_l3: l3 {};
-					pm8941_l4: l4 {};
-					pm8941_l5: l5 {};
-					pm8941_l6: l6 {};
-					pm8941_l7: l7 {};
-					pm8941_l8: l8 {};
-					pm8941_l9: l9 {};
-					pm8941_l10: l10 {};
-					pm8941_l11: l11 {};
-					pm8941_l12: l12 {};
-					pm8941_l13: l13 {};
-					pm8941_l14: l14 {};
-					pm8941_l15: l15 {};
-					pm8941_l16: l16 {};
-					pm8941_l17: l17 {};
-					pm8941_l18: l18 {};
-					pm8941_l19: l19 {};
-					pm8941_l20: l20 {};
-					pm8941_l21: l21 {};
-					pm8941_l22: l22 {};
-					pm8941_l23: l23 {};
-					pm8941_l24: l24 {};
-
-					pm8941_lvs1: lvs1 {};
-					pm8941_lvs2: lvs2 {};
-					pm8941_lvs3: lvs3 {};
-				};
-			};
-		};
-	};
-
-	vreg_boost: vreg-boost {
-		compatible = "regulator-fixed";
-
-		regulator-name = "vreg-boost";
-		regulator-min-microvolt = <3150000>;
-		regulator-max-microvolt = <3150000>;
-
-		regulator-always-on;
-		regulator-boot-on;
-
-		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&boost_bypass_n_pin>;
-	};
-	vreg_vph_pwr: vreg-vph-pwr {
-		compatible = "regulator-fixed";
-		regulator-name = "vph-pwr";
-
-		regulator-min-microvolt = <3600000>;
-		regulator-max-microvolt = <3600000>;
-
-		regulator-always-on;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
deleted file mode 100644
index 6740a4cb7da8..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974pro.dtsi
+++ /dev/null
@@ -1,18 +0,0 @@
-#include "qcom-msm8974.dtsi"
-
-/ {
-	soc {
-		sdhci@f9824900 {
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&xo_board>,
-				 <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
-				 <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
-			clock-names = "core", "iface", "xo", "cal", "sleep";
-		};
-
-		clock-controller@fc400000 {
-				compatible = "qcom,gcc-msm8974pro";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
new file mode 100644
index 000000000000..9cc1e14e6cd0
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/Makefile
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_QCOM) += \
+	qcom-apq8016-sbc.dtb \
+	qcom-apq8026-asus-sparrow.dtb \
+	qcom-apq8026-huawei-sturgeon.dtb \
+	qcom-apq8026-lg-lenok.dtb \
+	qcom-apq8026-samsung-matisse-wifi.dtb \
+	qcom-apq8060-dragonboard.dtb \
+	qcom-apq8064-cm-qs600.dtb \
+	qcom-apq8064-ifc6410.dtb \
+	qcom-apq8064-sony-xperia-lagan-yuga.dtb \
+	qcom-apq8064-asus-nexus7-flo.dtb \
+	qcom-apq8074-dragonboard.dtb \
+	qcom-apq8084-ifc6540.dtb \
+	qcom-apq8084-mtp.dtb \
+	qcom-ipq4018-ap120c-ac.dtb \
+	qcom-ipq4018-ap120c-ac-bit.dtb \
+	qcom-ipq4018-jalapeno.dtb \
+	qcom-ipq4019-ap.dk01.1-c1.dtb \
+	qcom-ipq4019-ap.dk04.1-c1.dtb \
+	qcom-ipq4019-ap.dk04.1-c3.dtb \
+	qcom-ipq4019-ap.dk07.1-c1.dtb \
+	qcom-ipq4019-ap.dk07.1-c2.dtb \
+	qcom-ipq8064-ap148.dtb \
+	qcom-ipq8064-rb3011.dtb \
+	qcom-msm8226-microsoft-dempsey.dtb \
+	qcom-msm8226-microsoft-makepeace.dtb \
+	qcom-msm8226-microsoft-moneypenny.dtb \
+	qcom-msm8226-samsung-s3ve3g.dtb \
+	qcom-msm8660-surf.dtb \
+	qcom-msm8916-samsung-e5.dtb \
+	qcom-msm8916-samsung-e7.dtb \
+	qcom-msm8916-samsung-grandmax.dtb \
+	qcom-msm8916-samsung-serranove.dtb \
+	qcom-msm8926-htc-memul.dtb \
+	qcom-msm8926-microsoft-superman-lte.dtb \
+	qcom-msm8926-microsoft-tesla.dtb \
+	qcom-msm8926-motorola-peregrine.dtb \
+	qcom-msm8960-cdp.dtb \
+	qcom-msm8960-samsung-expressatt.dtb \
+	qcom-msm8974-lge-nexus5-hammerhead.dtb \
+	qcom-msm8974-sony-xperia-rhine-amami.dtb \
+	qcom-msm8974-sony-xperia-rhine-honami.dtb \
+	qcom-msm8974pro-fairphone-fp2.dtb \
+	qcom-msm8974pro-oneplus-bacon.dtb \
+	qcom-msm8974pro-samsung-klte.dtb \
+	qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
+	qcom-mdm9615-wp8548-mangoh-green.dtb \
+	qcom-sdx55-mtp.dtb \
+	qcom-sdx55-t55.dtb \
+	qcom-sdx55-telit-fn980-tlb.dtb \
+	qcom-sdx65-mtp.dtb
diff --git a/arch/arm/boot/dts/qcom/pm8018.dtsi b/arch/arm/boot/dts/qcom/pm8018.dtsi
new file mode 100644
index 000000000000..22f3c7bac522
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8018.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Qualcomm PM8018
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+&ssbi {
+	pm8018: pmic {
+		compatible = "qcom,pm8018", "qcom,pm8921";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8018-pwrkey",
+				     "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupts-extended = <&pm8018 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8018 51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8018_mpps: mpps@50 {
+			compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8018_mpps 0 0 6>;
+		};
+
+		rtc@11d {
+			compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
+			reg = <0x11d>;
+			interrupts-extended = <&pm8018 39 IRQ_TYPE_EDGE_RISING>;
+			allow-set-time;
+		};
+
+		pm8018_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8018_gpio 0 0 6>;
+			#gpio-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8058.dtsi b/arch/arm/boot/dts/qcom/pm8058.dtsi
new file mode 100644
index 000000000000..984b79777984
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8058.dtsi
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&ssbi {
+	pm8058: pmic {
+		compatible = "qcom,pm8058";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8058-pwrkey";
+			reg = <0x1c>;
+			interrupts-extended = <&pm8058 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8058 51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8058_led48: led@48 {
+			compatible = "qcom,pm8058-keypad-led";
+			reg = <0x48>;
+			status = "disabled";
+		};
+
+		vibrator@4a {
+			compatible = "qcom,pm8058-vib";
+			reg = <0x4a>;
+		};
+
+		pm8058_mpps: mpps@50 {
+			compatible = "qcom,pm8058-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8058_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8058_led131: led@131 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x131>;
+			status = "disabled";
+		};
+
+		pm8058_led132: led@132 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x132>;
+			status = "disabled";
+		};
+
+		pm8058_led133: led@133 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x133>;
+			status = "disabled";
+		};
+
+		pm8058_keypad: keypad@148 {
+			compatible = "qcom,pm8058-keypad";
+			reg = <0x148>;
+			interrupts-extended = <&pm8058 74 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8058 75 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15>;
+			scan-delay = <32>;
+			row-hold = <91500>;
+		};
+
+		pm8058_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8058_gpio 0 0 44>;
+			#gpio-cells = <2>;
+		};
+
+		pm8058_xoadc: xoadc@197 {
+			compatible = "qcom,pm8058-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			ichg: adc-channel@3 {
+				reg = <0x00 0x03>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			ref_325mv: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+
+		rtc@1e8 {
+			compatible = "qcom,pm8058-rtc";
+			reg = <0x1e8>;
+			interrupts-extended = <&pm8058 39 IRQ_TYPE_EDGE_RISING>;
+			allow-set-time;
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8058_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8058_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8058_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8058_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8058_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8058_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8058_xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8226.dtsi b/arch/arm/boot/dts/qcom/pm8226.dtsi
new file mode 100644
index 000000000000..2fd4f135ed84
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8226.dtsi
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: BSD-3-Clause
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8226-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8226_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm8226_0: pm8226@0 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8226_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		smbb: charger@1000 {
+			compatible = "qcom,pm8226-charger";
+			reg = <0x1000>;
+			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "chg-done",
+					  "chg-fast",
+					  "chg-trkl",
+					  "bat-temp-ok",
+					  "bat-present",
+					  "chg-gone",
+					  "usb-valid",
+					  "dc-valid";
+
+			status = "disabled";
+
+			chg_otg: otg-vbus { };
+		};
+
+		pm8226_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8226_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			channel@7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+			channel@8 {
+				reg = <VADC_DIE_TEMP>;
+				label = "die_temp";
+			};
+			channel@9 {
+				reg = <VADC_REF_625MV>;
+				label = "ref_625mv";
+			};
+			channel@a {
+				reg = <VADC_REF_1250MV>;
+				label = "ref_1250mv";
+			};
+			channel@e {
+				reg = <VADC_GND_REF>;
+			};
+			channel@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8226_iadc: adc@3600 {
+			compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
+			reg = <0x3600>;
+			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pm8226_mpps: mpps@a000 {
+			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8226_gpios: gpio@c000 {
+			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_gpios 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8226_1: pm8226@1 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8226_spmi_regulators: regulators {
+			compatible = "qcom,pm8226-regulators";
+		};
+
+		pm8226_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8821.dtsi b/arch/arm/boot/dts/qcom/pm8821.dtsi
new file mode 100644
index 000000000000..064e3ba54e18
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8821.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This PMIC is used on a secondary SSBI bus */
+&ssbi2 {
+	pm8821: pmic {
+		compatible = "qcom,pm8821";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8821_mpps: mpps@50 {
+			compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8821_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom/pm8841.dtsi
index 2fd59c440903..3bf2ce5c86a6 100644
--- a/arch/arm/boot/dts/qcom-pm8841.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8841.dtsi
@@ -2,6 +2,37 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+
+/ {
+	thermal-zones {
+		pm8841-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8841_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <140000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 
 	pm8841_0: pm8841@4 {
@@ -15,16 +46,16 @@
 			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			interrupts = <4 0xa0 0 IRQ_TYPE_NONE>,
-				     <4 0xa1 0 IRQ_TYPE_NONE>,
-				     <4 0xa2 0 IRQ_TYPE_NONE>,
-				     <4 0xa3 0 IRQ_TYPE_NONE>;
+			gpio-ranges = <&pm8841_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
-		temp-alarm@2400 {
+		pm8841_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
 			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <0>;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
new file mode 100644
index 000000000000..058962af3005
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&ssbi {
+	pm8921: pmic {
+		compatible = "qcom,pm8921";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupts-extended = <&pm8921 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8921 51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8921_mpps: mpps@50 {
+			compatible = "qcom,pm8921-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8921_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		rtc@11d {
+			compatible = "qcom,pm8921-rtc";
+			reg = <0x11d>;
+			interrupts-extended = <&pm8921 39 IRQ_TYPE_EDGE_RISING>;
+			allow-set-time;
+		};
+
+		pm8921_keypad: keypad@148 {
+			compatible = "qcom,pm8921-keypad";
+			reg = <0x148>;
+			interrupts-extended = <&pm8921 74 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8921 75 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15>;
+			scan-delay = <32>;
+			row-hold = <91500>;
+			status = "disabled";
+		};
+
+		pm8921_gpio: gpio@150 {
+
+			compatible = "qcom,pm8921-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8921_gpio 0 0 44>;
+			#gpio-cells = <2>;
+
+		};
+
+		pm8921_xoadc: xoadc@197 {
+			compatible = "qcom,pm8921-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			batt_therm: adc-channel@8 {
+				reg = <0x00 0x08>;
+			};
+
+			batt_id: adc-channel@9 {
+				reg = <0x00 0x09>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			chg_temp: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom/pm8941.dtsi
index c1f2012d1c8b..aca0052a02b7 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8941.dtsi
@@ -3,6 +3,37 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+
+/ {
+	thermal-zones {
+		pm8941-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8941_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 
 	pm8941_0: pm8941@0 {
@@ -19,15 +50,27 @@
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
-		pwrkey@800 {
-			compatible = "qcom,pm8941-pwrkey";
+		pon@800 {
+			compatible = "qcom,pm8941-pon";
 			reg = <0x800>;
-			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
-			debounce = <15625>;
-			bias-pull-up;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+			};
+
+			pm8941_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
 		};
 
-		usb_id: misc@900 {
+		usb_id: usb-detect@900 {
 			compatible = "qcom,pm8941-misc";
 			reg = <0x900>;
 			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
@@ -56,10 +99,12 @@
 
 			usb-otg-in-supply = <&pm8941_5vs1>;
 
+			status = "disabled";
+
 			chg_otg: otg-vbus { };
 		};
 
-		pm8941_gpios: gpios@c000 {
+		pm8941_gpios: gpio@c000 {
 			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
@@ -68,7 +113,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			boost_bypass_n_pin: boost-bypass {
+			boost_bypass_n_pin: boost-bypass-state {
 				pins = "gpio21";
 				function = "normal";
 			};
@@ -79,14 +124,9 @@
 			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
-				     <0 0xa1 0 IRQ_TYPE_NONE>,
-				     <0 0xa2 0 IRQ_TYPE_NONE>,
-				     <0 0xa3 0 IRQ_TYPE_NONE>,
-				     <0 0xa4 0 IRQ_TYPE_NONE>,
-				     <0 0xa5 0 IRQ_TYPE_NONE>,
-				     <0 0xa6 0 IRQ_TYPE_NONE>,
-				     <0 0xa7 0 IRQ_TYPE_NONE>;
+			gpio-ranges = <&pm8941_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		pm8941_temp: temp-alarm@2400 {
@@ -98,7 +138,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		pm8941_vadc: vadc@3100 {
+		pm8941_vadc: adc@3100 {
 			compatible = "qcom,spmi-vadc";
 			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
@@ -106,37 +146,44 @@
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
 
-			bat_temp {
-				reg = <VADC_LR_MUX1_BAT_THERM>;
+
+			channel@6 {
+				reg = <VADC_VBAT_SNS>;
 			};
-			die_temp {
+
+			channel@8 {
 				reg = <VADC_DIE_TEMP>;
 			};
-			ref_625mv {
+
+			channel@9 {
 				reg = <VADC_REF_625MV>;
 			};
-			ref_1250v {
+
+			channel@a {
 				reg = <VADC_REF_1250MV>;
 			};
-			ref_gnd {
+
+			channel@e {
 				reg = <VADC_GND_REF>;
 			};
-			ref_vdd {
+
+			channel@f {
 				reg = <VADC_VDD_VADC>;
 			};
-			vbat_sns {
-				reg = <VADC_VBAT_SNS>;
+
+			channel@30 {
+				reg = <VADC_LR_MUX1_BAT_THERM>;
 			};
 		};
 
-		pm8941_iadc: iadc@3600 {
+		pm8941_iadc: adc@3600 {
 			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
 			reg = <0x3600>;
 			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
 			qcom,external-resistor-micro-ohms = <10000>;
 		};
 
-		coincell@2800 {
+		pm8941_coincell: charger@2800 {
 			compatible = "qcom,pm8941-coincell";
 			reg = <0x2800>;
 			status = "disabled";
@@ -149,6 +196,22 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8941_lpg: pwm {
+			compatible = "qcom,pm8941-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
+		pm8941_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+
 		pm8941_wled: wled@d800 {
 			compatible = "qcom,pm8941-wled";
 			reg = <0xd800>;
diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom/pma8084.dtsi
index ea1ca166165c..2985f4805b93 100644
--- a/arch/arm/boot/dts/qcom-pma8084.dtsi
+++ b/arch/arm/boot/dts/qcom/pma8084.dtsi
@@ -27,7 +27,7 @@
 			bias-pull-up;
 		};
 
-		pma8084_gpios: gpios@c000 {
+		pma8084_gpios: gpio@c000 {
 			compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
@@ -42,14 +42,9 @@
 			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
-				     <0 0xa1 0 IRQ_TYPE_NONE>,
-				     <0 0xa2 0 IRQ_TYPE_NONE>,
-				     <0 0xa3 0 IRQ_TYPE_NONE>,
-				     <0 0xa4 0 IRQ_TYPE_NONE>,
-				     <0 0xa5 0 IRQ_TYPE_NONE>,
-				     <0 0xa6 0 IRQ_TYPE_NONE>,
-				     <0 0xa7 0 IRQ_TYPE_NONE>;
+			gpio-ranges = <&pma8084_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		pma8084_temp: temp-alarm@2400 {
@@ -61,31 +56,35 @@
 			io-channel-names = "thermal";
 		};
 
-		pma8084_vadc: vadc@3100 {
+		pma8084_vadc: adc@3100 {
 			compatible = "qcom,spmi-vadc";
 			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 
-			die_temp {
+			channel@8 {
 				reg = <VADC_DIE_TEMP>;
 			};
-			ref_625mv {
+
+			channel@9 {
 				reg = <VADC_REF_625MV>;
 			};
-			ref_1250v {
+
+			channel@a {
 				reg = <VADC_REF_1250MV>;
 			};
-			ref_buf_625mv {
+
+			channel@c {
 				reg = <VADC_SPARE1>;
 			};
-			ref_gnd {
+
+			channel@e {
 				reg = <VADC_GND_REF>;
 			};
-			ref_vdd {
+
+			channel@f {
 				reg = <VADC_VDD_VADC>;
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom/pmx55.dtsi b/arch/arm/boot/dts/qcom/pmx55.dtsi
new file mode 100644
index 000000000000..da0851173c69
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pmx55.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020, Linaro Limited
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@8 {
+		compatible = "qcom,pmx55", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+
+			status = "disabled";
+		};
+
+		pmx55_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x8 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmx55_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmx55_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x8 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			channel@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			channel@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			channel@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+
+			channel@9 {
+				reg = <ADC5_CHG_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "chg_temp";
+			};
+		};
+
+		pmx55_gpios: gpio@c000 {
+			compatible = "qcom,pmx55-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pmx55_gpios 0 0 11>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@9 {
+		compatible = "qcom,pmx55", "qcom,spmi-pmic";
+		reg = <0x9 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pmx65.dtsi b/arch/arm/boot/dts/qcom/pmx65.dtsi
new file mode 100644
index 000000000000..1c7fdf59c1f5
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pmx65.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@1 {
+		compatible = "qcom,pmx65", "qcom,spmi-pmic";
+		reg = <1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmx65_temp: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmx65_gpios: gpio@8800 {
+			compatible = "qcom,pmx65-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmx65_gpios 0 0 16>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts b/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts
new file mode 100644
index 000000000000..4ccd2dca74a2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/apq8016-sbc.dts"
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
new file mode 100644
index 000000000000..a2ca456012f1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "ASUS ZenWatch 2";
+	compatible = "asus,sparrow", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 3005>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart1_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a1-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+		};
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 46 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <350000>;
+	qcom,fast-charge-safe-voltage = <4430000>;
+	qcom,fast-charge-high-threshold-voltage = <4400000>;
+	qcom,auto-recharge-threshold-voltage = <4300000>;
+	qcom,minimum-input-voltage = <4400000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	blsp1_uart1_default_state: blsp1-uart1-default-state {
+		pins = "gpio0", "gpio1", "gpio2", "gpio3";
+		function = "blsp_uart1";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio48", "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
new file mode 100644
index 000000000000..ac228965a485
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+#include <dt-bindings/input/ti-drv260x.h>
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "Huawei Watch";
+	compatible = "huawei,sturgeon", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 4>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	vibrator@5a {
+		compatible = "ti,drv2605";
+		reg = <0x5a>;
+		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+
+		mode = <DRV260X_ERM_MODE>;
+		library-sel = <DRV260X_ERM_LIB_D>;
+		vib-rated-mv = <2765>;
+		vib-overdrive-mv = <3525>;
+
+		pinctrl-0 = <&vibrator_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp1_i2c5 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		vio-supply = <&pm8226_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		syna,startup-delay-ms = <160>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_3 {
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-voltage = <4370000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,minimum-input-voltage = <4350000>;
+	qcom,fast-charge-current-limit = <300000>;
+	qcom,fast-charge-safe-current = <600000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio63", "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	touch_default_state: touch-default-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	vibrator_default_state: vibrator-default-state {
+		pins = "gpio59", "gpio60";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
new file mode 100644
index 000000000000..0a1fd5eb3c6d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
@@ -0,0 +1,358 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "LG G Watch R";
+	compatible = "lg,lenok", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,board-id = <132 0x0a>;
+	qcom,msm-id = <199 0x20000>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+		serial1 = &blsp1_uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x03100000 0x200000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3300000 {
+			reg = <0x03300000 0x1400000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	fuel-gauge@55 {
+		compatible = "ti,bq27421";
+		reg = <0x55>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+	clock-frequency = <384000>;
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l22>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pins>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&blsp1_uart4 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <450000>;
+	qcom,fast-charge-current-limit = <400000>;
+	qcom,fast-charge-safe-voltage = <4350000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+	qcom,minimum-input-voltage = <4450000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio47", "gpio48";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	touch_pins: touch-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio37";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
new file mode 100644
index 000000000000..cffc069712b2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -0,0 +1,519 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &smem_region;
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1";
+	compatible = "samsung,matisse-wifi", "qcom,apq8026";
+	chassis-type = "tablet";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+		display0 = &framebuffer0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <1280>;
+			height = <800>;
+			stride = <(1280 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 110 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-backlight {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&backlight_i2c_default_state>;
+		pinctrl-names = "default";
+
+		i2c-gpio,delay-us = <4>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x3f>;
+
+			pwms = <&backlight_pwm 0 100000>;
+			pwm-names = "lp8556";
+
+			rom-a0h {
+				rom-addr = /bits/ 8 <0xa0>;
+				rom-val = /bits/ 8 <0x44>;
+			};
+
+			rom-a1h {
+				rom-addr = /bits/ 8 <0xa1>;
+				rom-val = /bits/ 8 <0x6c>;
+			};
+
+			rom-a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x24>;
+			};
+		};
+	};
+
+	backlight_pwm: pwm {
+		compatible = "clk-pwm";
+		#pwm-cells = <2>;
+		clocks = <&mmcc CAMSS_GP0_CLK>;
+		pinctrl-0 = <&backlight_pwm_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_1p8v: regulator-tsp-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_1p8v";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en_default_state>;
+	};
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		mpss@8400000 {
+			reg = <0x08400000 0x1f00000>;
+			no-map;
+		};
+
+		mba@a300000 {
+			reg = <0x0a300000 0x100000>;
+			no-map;
+		};
+
+		reserved@cb00000 {
+			reg = <0x0cb00000 0x700000>;
+			no-map;
+		};
+
+		wcnss@d200000 {
+			reg = <0x0d200000 0x700000>;
+			no-map;
+		};
+
+		adsp_region: adsp@d900000 {
+			reg = <0x0d900000 0x1800000>;
+			no-map;
+		};
+
+		venus@f100000 {
+			reg = <0x0f100000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x260000>;
+			no-map;
+		};
+
+		rfsa@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@1d {
+		compatible = "st,lis2hh12";
+		reg = <0x1d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default_state>;
+
+		st,drdy-int-pin = <1>;
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+	};
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	muic: usb-switch@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		reg = <0x25>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&muic_int_default_state>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_int_rst_default_state>;
+
+		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&reg_tsp_1p8v>;
+		vdda-supply = <&reg_tsp_3p3v>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+			regulator-always-on;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default_state: accel-int-default-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_i2c_default_state: backlight-i2c-default-state {
+		pins = "gpio20", "gpio21";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_pwm_default_state: backlight-pwm-default-state {
+		pins = "gpio33";
+		function = "gp0_clk";
+	};
+
+	muic_int_default_state: muic-int-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default_state: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio73";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_rst_default_state: tsp-int-rst-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
new file mode 100644
index 000000000000..009afd8212c2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,1024 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include "qcom-msm8660.dtsi"
+#include "pm8058.dtsi"
+
+/ {
+	model = "Qualcomm APQ8060 Dragonboard";
+	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Main power of the board: 3.7V */
+	vph: regulator-fixed {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-name = "VPH";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* GPIO controlled ethernet power regulator */
+	dragon_veth: xc622a331mrg {
+		compatible = "regulator-fixed";
+		regulator-name = "XC6222A331MR-G";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vph>;
+		gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_veth_gpios>;
+		regulator-always-on;
+	};
+
+	/* VDDvario fixed regulator */
+	dragon_vario: nds332p {
+		compatible = "regulator-fixed";
+		regulator-name = "NDS332P";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&pm8058_s3>;
+	};
+
+	/* This is a levelshifter for SDCC5 */
+	dragon_vio_txb: txb0104rgyr {
+		compatible = "regulator-fixed";
+		regulator-name = "Dragon SDCC levelshifter";
+		vin-supply = <&pm8058_l14>;
+		regulator-always-on;
+	};
+
+	/*
+	 * Capella CM3605 light and proximity sensor mounted directly
+	 * on the sensor board.
+	 */
+	cm3605 {
+		compatible = "capella,cm3605";
+		vdd-supply = <&pm8058_l14>; // 2.85V
+		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
+		capella,aset-resistance-ohms = <100000>;
+		/* Trig on both edges - getting close or far away */
+		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
+		/* MPP05 analog input to the XOADC */
+		io-channels = <&pm8058_xoadc 0x00 0x05>;
+		io-channel-names = "aout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
+	};
+};
+
+&ebi2 {
+	/* The EBI2 will instantiate first, then populate its children */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_ebi2_pins>;
+	status = "okay";
+
+	/*
+	 * An on-board SMSC LAN9221 chip for "debug ethernet",
+	 * which is actually just an ordinary ethernet on the
+	 * EBI2. This has a 25MHz chrystal next to it, so no
+	 * clocking is needed.
+	 */
+	ethernet@2,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		reg = <2 0x0 0x100>;
+		/*
+		 * The second interrupt is the PME interrupt
+		 * for network wakeup, connected to the TLMM.
+		 */
+		interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
+				    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+		vdd33a-supply = <&dragon_veth>;
+		vddvario-supply = <&dragon_vario>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ethernet_gpios>;
+		phy-mode = "mii";
+		reg-io-width = <2>;
+		smsc,force-external-phy;
+		smsc,irq-push-pull;
+
+		/*
+		 * SLOW chipselect config
+		 * Delay 9 cycles (140ns@64MHz) between SMSC
+		 * LAN9221 Ethernet controller reads and writes
+		 * on CS2.
+		 */
+		qcom,xmem-recovery-cycles = <0>;
+		qcom,xmem-write-hold-cycles = <3>;
+		qcom,xmem-write-delta-cycles = <31>;
+		qcom,xmem-read-delta-cycles = <28>;
+		qcom,xmem-write-wait-cycles = <9>;
+		qcom,xmem-read-wait-cycles = <9>;
+	};
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,cy8ctma340";
+		reg = <0x24>;
+		/* Certainly we can do at least 400 kHz */
+		clock-frequency = <400000>;
+		/* IRQ on GPIO61 called /CTP_INT */
+		interrupt-parent = <&tlmm>;
+		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+		/*
+		 * The I2C bus is using a PCA9306 level translator from L16A
+		 * to L2B so these two voltages are needed and L16A is
+		 * kind of the IO voltage, however L16Aisn't really fed to
+		 * the TMA340, which relies entirely on L2B (PM8901 L2).
+		 */
+		vcpin-supply = <&pm8058_l16>;
+		vdd-supply = <&pm8901_l2>;
+		/* GPIO58, called WAKE_CTP */
+		reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		active-interval-ms = <0>;
+		touch-timeout-ms = <255>;
+		lowpower-interval-ms = <10>;
+		bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_tma340_gpios>;
+	};
+};
+
+&gsbi8 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi8_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+	status = "okay";
+
+	eeprom@52 {
+		/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		vcc-supply = <&pm8058_s3>;
+		pagesize = <64>;
+	};
+	wm8903: wm8903@1a {
+		/* This Woolfson Micro device has an unrouted interrupt line */
+		compatible = "wlf,wm8903";
+		reg = <0x1a>;
+
+		AVDD-supply = <&pm8058_l16>;
+		CPVDD-supply = <&pm8058_l16>;
+		DBVDD-supply = <&pm8058_s3>;
+		DCVDD-supply = <&pm8058_l0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		micdet-cfg = <0>;
+		micdet-delay = <100>;
+		gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+	};
+};
+
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi12_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+	status = "okay";
+};
+
+&gsbi12_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+	status = "okay";
+
+	ak8975@c {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0c>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <33 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ak8975_gpios>;
+		vid-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+	};
+	bmp085@77 {
+		compatible = "bosch,bmp085";
+		reg = <0x77>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_bmp085_gpios>;
+		vddd-supply = <&pm8058_lvs0>; // 1.8V
+		vdda-supply = <&pm8058_l14>; // 2.85V
+	};
+	mpu3050@68 {
+		compatible = "invensense,mpu3050";
+		reg = <0x68>;
+		/*
+		 * GPIO17 is pulled high by a 10k
+		 * resistor to VLOGIC so needs to be
+		 * active low/falling edge.
+		 */
+		interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_mpu3050_gpios>;
+		vlogic-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+
+		/*
+		 * The MPU-3050 acts as a hub for the
+		 * accelerometer.
+		 */
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			kxsd9@18 {
+				compatible = "kionix,kxsd9";
+				reg = <0x18>;
+				interrupt-parent = <&tlmm>;
+				interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_kxsd9_gpios>;
+				iovdd-supply = <&pm8058_lvs0>; // 1.8V
+				vdd-supply = <&pm8058_l14>; // 2.85V
+			};
+		};
+	};
+};
+
+&pm8058 {
+	interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8058_gpio {
+	dragon_ethernet_gpios: ethernet-state {
+		pinconf {
+			pins = "gpio7";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_bmp085_gpios: bmp085-state {
+		pinconf {
+			pins = "gpio16";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_mpu3050_gpios: mpu3050-state {
+		pinconf {
+			pins = "gpio17";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc3_gpios: sdcc3-state {
+		pinconf {
+			pins = "gpio22";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc5_gpios: sdcc5-state {
+		pinconf {
+			pins = "gpio26";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_ak8975_gpios: ak8975-state {
+		pinconf {
+			pins = "gpio33";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_cm3605_gpios: cm3605-state {
+		/* Pin 34 connected to the proxy IRQ */
+		gpio34-pins {
+			pins = "gpio34";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+		/* Pin 35 connected to ASET */
+		gpio35-pins {
+			pins = "gpio35";
+			function = "normal";
+			output-high;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_veth_gpios: veth-state {
+		pinconf {
+			pins = "gpio40";
+			function = "normal";
+			bias-disable;
+			drive-push-pull;
+		};
+	};
+};
+
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_MENU)
+		MATRIX_KEY(0, 2, KEY_1)
+		MATRIX_KEY(0, 3, KEY_4)
+		MATRIX_KEY(0, 4, KEY_7)
+		MATRIX_KEY(1, 0, KEY_UP)
+		MATRIX_KEY(1, 1, KEY_LEFT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_5)
+		MATRIX_KEY(1, 3, KEY_8)
+		MATRIX_KEY(2, 0, KEY_HOME)
+		MATRIX_KEY(2, 1, KEY_REPLY)
+		MATRIX_KEY(2, 2, KEY_2)
+		MATRIX_KEY(2, 3, KEY_6)
+		MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(3, 1, KEY_RIGHT)
+		MATRIX_KEY(3, 2, KEY_3)
+		MATRIX_KEY(3, 3, KEY_9)
+		MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+		MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+		MATRIX_KEY(4, 1, KEY_BACK)
+		MATRIX_KEY(4, 2, KEY_CAMERA)
+		MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+	>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
+};
+
+&pm8058_led48 {
+	/*
+	 * The keypad LED @0x48 is routed to
+	 * the sensor board where it is
+	 * connected to an infrared LED
+	 * SFH4650 (60mW, @850nm) next to the
+	 * ambient light and proximity sensor
+	 * Capella Microsystems CM3605.
+	 */
+	label = "pm8058:infrared:proximitysensor";
+	default-state = "off";
+	linux,default-trigger = "cm3605";
+	status = "okay";
+};
+
+&pm8058_led131 {
+	label = "pm8058:red";
+	color = <LED_COLOR_ID_RED>;
+	default-state = "off";
+	status = "okay";
+};
+
+&pm8058_led132 {
+	/*
+	 * This is actually green too on my
+	 * board, but documented as yellow.
+	 */
+	label = "pm8058:yellow";
+	color = <LED_COLOR_ID_YELLOW>;
+	default-state = "off";
+	linux,default-trigger = "mmc0";
+	status = "okay";
+};
+
+&pm8058_led133 {
+	label = "pm8058:green";
+	function = LED_FUNCTION_HEARTBEAT;
+	color = <LED_COLOR_ID_GREEN>;
+	default-state = "on";
+	linux,default-trigger = "heartbeat";
+	status = "okay";
+};
+
+&pm8058_mpps {
+	dragon_cm3605_mpps: cm3605-mpps-state {
+		pins = "mpp5";
+		function = "analog";
+		input-enable;
+		bias-high-impedance;
+		/* Let's use channel 5 */
+		qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+		power-source = <PM8058_GPIO_S3>;
+	};
+};
+
+&rpm {
+	/*
+	 * Set up of the PMIC RPM regulators for this board
+	 * PM8901 supplies "preliminary regulators" whatever
+	 * that means
+	 */
+	regulators-0 {
+		compatible = "qcom,rpm-pm8901-regulators";
+
+		vdd_l0-supply = <&pm8901_s4>;
+		vdd_l1-supply = <&vph>;
+		vdd_l2-supply = <&vph>;
+		vdd_l3-supply = <&vph>;
+		vdd_l4-supply = <&vph>;
+		vdd_l5-supply = <&vph>;
+		vdd_l6-supply = <&vph>;
+		/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		lvs0_in-supply = <&pm8058_s3>;
+		lvs1_in-supply = <&pm8901_s4>;
+		lvs2_in-supply = <&pm8058_l0>;
+		lvs3_in-supply = <&pm8058_s2>;
+		mvs_in-supply = <&pm8058_s3>;
+
+		pm8901_l0: l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8901_l1: l1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8901_l2: l2 {
+			/* TMA340 requires strictly 3.3V */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8901_l3: l3 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8901_l4: l4 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8901_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8901_l6: l6 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+
+		/* s0 and s1 are SAW regulators controlled over SPM */
+		pm8901_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		pm8901_s3: s3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		pm8901_s4: s4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* LVS0 thru 3 and mvs are just switches */
+		pm8901_lvs0: lvs0 {
+			regulator-always-on;
+		};
+
+		pm8901_lvs1: lvs1 { };
+
+		pm8901_lvs2: lvs2 { };
+
+		pm8901_lvs3: lvs3 { };
+
+		pm8901_mvs: mvs { };
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8058-regulators";
+
+		vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+		vdd_l2_l11_l12-supply = <&vph>;
+		vdd_l3_l4_l5-supply = <&vph>;
+		vdd_l6_l7-supply = <&vph>;
+		vdd_l8-supply = <&vph>;
+		vdd_l9-supply = <&vph>;
+		vdd_l10-supply = <&vph>;
+		vdd_l13_l16-supply = <&pm8058_s4>;
+		vdd_l14_l15-supply = <&vph>;
+		vdd_l17_l18-supply = <&vph>;
+		vdd_l19_l20-supply = <&vph>;
+		vdd_l21-supply = <&pm8058_s3>;
+		vdd_l22-supply = <&pm8058_s3>;
+		vdd_l23_l24_l25-supply = <&pm8058_s3>;
+		vdd_s0-supply = <&vph>;
+		vdd_s1-supply = <&vph>;
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		vdd_ncp-supply = <&vph>;
+
+		pm8058_l0: l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l1: l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l2: l2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l3: l3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l4: l4 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8058_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8058_l6: l6 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3050000>;
+			bias-pull-down;
+		};
+
+		pm8058_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l10: l10 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l11: l11 {
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+
+		pm8058_l12: l12 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+
+		pm8058_l13: l13 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			bias-pull-down;
+		};
+
+		pm8058_l14: l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8058_l15: l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8058_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		pm8058_l17: l17 {
+			// 1.5V according to schematic
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l18: l18 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l19: l19 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			bias-pull-down;
+		};
+
+		pm8058_l20: l20 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l21: l21 {
+			// 1.1 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		pm8058_l22: l22 {
+			// 1.2 V according to schematic
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8058_l23: l23 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l24: l24 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l25: l25 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_s0: s0 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1325000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8058_s1: s1 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1250000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8058_s2: s2 {
+			// 1.3 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8058_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		pm8058_s4: s4 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		/* LVS0 and LVS1 are just switches */
+		pm8058_lvs0: lvs0 {
+			bias-pull-down;
+		};
+
+		pm8058_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8058_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* Internal 3.69 GiB eMMC */
+&sdcc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc1_pins>;
+	vmmc-supply = <&pm8901_l5>;
+	vqmmc-supply = <&pm8901_lvs0>;
+	status = "okay";
+};
+
+/* External micro SD card, directly connected, pulled up to 2.85 V */
+&sdcc3 {
+	/* Enable SSBI GPIO 22 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+	cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	status = "okay";
+};
+
+/*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+&sdcc5 {
+	/* Enable SSBI GPIO 26 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+	cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	vqmmc-supply = <&dragon_vio_txb>;
+	status = "okay";
+};
+
+&tlmm {
+	/* eMMC pins, all 8 data lines connected */
+	dragon_sdcc1_pins: sdcc1-state {
+		clk-pins {
+			pins = "gpio167"; /* SDC1 CLK */
+			function = "sdc1";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio168"; /* SDC1 CMD */
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC1 D0 to D7 */
+			pins = "gpio159", "gpio160", "gpio161", "gpio162",
+			     "gpio163", "gpio164", "gpio165", "gpio166";
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	/*
+	 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+	 * configuration.
+	 */
+	dragon_sdcc3_pins: sdcc3-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	/* Second SD card slot pins */
+	dragon_sdcc5_pins: sdcc5-state {
+		clk-pins {
+			pins = "gpio97"; /* SDC5 CLK */
+			function = "sdc5";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio95"; /* SDC5 CMD */
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC5 D0 to D3 */
+			pins = "gpio96", "gpio98", "gpio99", "gpio100";
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_gsbi3_i2c_pins: gsbi3-i2c-state {
+		pins = "gpio43", "gpio44";
+		function = "gsbi3";
+		drive-strength = <8>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi8_i2c_pins: gsbi8-i2c-state {
+		pins = "gpio64", "gpio65";
+		function = "gsbi8";
+		drive-strength = <16>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi12_i2c_pins: gsbi12-i2c-state {
+		pins = "gpio115", "gpio116";
+		function = "gsbi12";
+		drive-strength = <16>;
+		/* These have external pull-up 4.7kOhm to 1.8V */
+		bias-disable;
+	};
+
+	/* Primary serial port uart 0 pins */
+	dragon_gsbi12_serial_pins: gsbi12-serial-state {
+		tx-pins {
+			pins = "gpio117";
+			function = "gsbi12";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		rx-pins {
+			pins = "gpio118";
+			function = "gsbi12";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_ebi2_pins: ebi2-state {
+		/*
+		 * Pins used by EBI2 on the Dragonboard, actually only
+		 * CS2 is used by a real peripheral. CS0 is just
+		 * routed to a test point.
+		 */
+		mux0-pins {
+			pins =
+			    /* "gpio39", CS1A_N this is not good to mux */
+			    "gpio40", /* CS2A_N */
+			    "gpio134"; /* CS0_N testpoint TP29 */
+			function = "ebi2cs";
+		};
+		mux1-pins {
+			pins =
+			    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
+			    "gpio123", "gpio124", "gpio125", "gpio126",
+			    "gpio127", "gpio128", "gpio129", "gpio130",
+			    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
+			    "gpio135", "gpio136", "gpio137", "gpio138",
+			    "gpio139", "gpio140", "gpio141", "gpio142",
+			    "gpio143", "gpio144", "gpio145", "gpio146",
+			    "gpio147", "gpio148", "gpio149", "gpio150",
+			    "gpio151", /* EBI2_OE_N */
+			    "gpio153", /* EBI2_ADV */
+			    "gpio157"; /* EBI2_WE_N */
+			function = "ebi2";
+		};
+	};
+
+	/* Interrupt line for the KXSD9 accelerometer */
+	dragon_kxsd9_gpios: kxsd9-state {
+		pins = "gpio57"; /* IRQ line */
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	dragon_tma340_gpios: tma340-state {
+		reset-pins {
+			/* RESET line, TS_ATTN, WAKE_CTP */
+			pins = "gpio58";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-disable;
+		};
+		irq-pins {
+			pins = "gpio61"; /* IRQ line */
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&pm8058_xoadc {
+	/* Reference voltage 2.2 V */
+	xoadc-ref-supply = <&pm8058_l18>;
+
+	/* Board-specific channels */
+	adc-channel@5 {
+		/* Connected to AOUT of ALS sensor */
+		reg = <0x00 0x05>;
+	};
+
+	adc-channel@6 {
+		/* Connected to test point TP43 */
+		reg = <0x00 0x06>;
+	};
+
+	adc-channel@7 {
+		/* Connected to battery thermistor */
+		reg = <0x00 0x07>;
+	};
+
+	adc-channel@8 {
+		/* Connected to battery ID detector */
+		reg = <0x00 0x08>;
+	};
+
+	adc-channel@9 {
+		/* Connected to XO thermistor */
+		reg = <0x00 0x09>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
new file mode 100644
index 000000000000..d460743fbb94
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -0,0 +1,363 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Asus Nexus7(flo)";
+	compatible = "asus,nexus7-flo", "qcom,apq8064";
+	chassis-type = "tablet";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@88d00000 {
+			compatible = "ramoops";
+			reg = <0x88d00000 0x100000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
+		};
+	};
+
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	soc {
+		sram@2a03f000 {
+			compatible = "qcom,apq8064-imem", "syscon", "simple-mfd";
+			reg = <0x2a03f000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+
+				mode-normal = <0x77665501>;
+				mode-bootloader = <0x77665500>;
+				mode-recovery = <0x77665502>;
+			};
+		};
+	};
+};
+
+&dsi0 {
+	vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+	vdd-supply = <&pm8921_l8>;
+	vddio-supply = <&pm8921_lvs7>;
+	avdd-supply = <&pm8921_l11>;
+	status = "okay";
+
+	panel@0 {
+		reg = <0>;
+		compatible = "jdi,lt070me05000";
+
+		vddp-supply = <&pm8921_l17>;
+		iovcc-supply = <&pm8921_lvs7>;
+
+		enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
+		dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_in {
+	remote-endpoint = <&mdp_dsi1_out>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+
+	bq27541@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+	};
+
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	clock-frequency = <200000>;
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	trackpad@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		interrupt-parent = <&tlmm_pinmux>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdp_dsi1_out {
+	remote-endpoint = <&dsi0_in>;
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vin_lvs2-supply = <&pm8921_s1>;
+
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		vdd_ncp-supply = <&pm8921_l6>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		/* msm otg HSUSB_VDDCX */
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		/*
+		 * msm_sdcc.1-sdc-vdd_io
+		 * tabla2x-slim-CDC_VDDA_RX
+		 * tabla2x-slim-CDC_VDDA_TX
+		 * tabla2x-slim-CDC_VDD_CP
+		 * tabla2x-slim-VDDIO_CDC
+		 */
+		pm8921_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+			regulator-always-on;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		/* mipi_dsi.1-dsi1_pll_vdda */
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on;
+		};
+
+		/* msm_otg-HSUSB_3p3 */
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		/* msm_otg-HSUSB_1p8 */
+		pm8921_l4: l4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/* msm_sdcc.1-sdc_vdd */
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8921_l8: l8 {
+		};
+
+		/* mipi_dsi.1-dsi1_avdd */
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		/* pwm_power for backlight */
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+
+		/* camera, qdsp6 */
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/*
+		 * tabla2x-slim-CDC_VDDA_A_1P2V
+		 * tabla2x-slim-VDDD_CDC_D
+		 */
+		pm8921_l25: l25 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+		/*
+		 * mipi_dsi.1-dsi1_vddio
+		 * pil_riva-pll_vdd
+		 */
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
new file mode 100644
index 000000000000..671d58cc2741
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "CompuLab CM-QS600";
+	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
+
+	/* on board fixed 3.3v supply */
+	v3p3_fixed: regulator-v3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE V3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&pcie {
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&v3p3_fixed>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		pm8921_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&v3p3_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	status = "okay";
+	vmmc-supply = <&v3p3_fixed>;
+	vqmmc-supply = <&v3p3_fixed>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+};
+
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
new file mode 100644
index 000000000000..ed86b24119c9
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -0,0 +1,374 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Qualcomm APQ8064/IFC6410";
+	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+		i2c0 = &gsbi1_i2c;
+		i2c1 = &gsbi2_i2c;
+		i2c2 = &gsbi3_i2c;
+		i2c3 = &gsbi4_i2c;
+		spi0 = &gsbi5_spi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&notify_led>;
+
+		led-user1 {
+			label = "apq8064:green:user1";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
+
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	status = "okay";
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+/* CAM I2C MIPI-CSI connector */
+&gsbi4_i2c {
+	status = "okay";
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+};
+
+&gsbi5_spi {
+	num-cs = <1>;
+	cs-gpios = <&tlmm_pinmux 53 0>;
+	status = "okay";
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&hdmi {
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+	hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&hdmi_in {
+	remote-endpoint = <&mdp_dtv_out>;
+};
+
+&hdmi_out {
+	remote-endpoint = <&hdmi_con>;
+};
+
+&hdmi_phy {
+	status = "okay";
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdp_dtv_out {
+	remote-endpoint = <&hdmi_in>;
+};
+
+&pcie {
+	status = "okay";
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&ext_3p3v>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+
+	notify_led: nled-state {
+		pinconf {
+			pins = "gpio18";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		pm8921_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_hdmi_switch: hdmi-switch {
+			bias-pull-down;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata0 {
+	target-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	vmmc-supply = <&ext_3p3v>;
+	vqmmc-supply = <&pm8921_lvs1>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi
index cbe42c4153a0..7c545c50847b 100644
--- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi
@@ -76,7 +76,7 @@
 		pinconf {
 			pins = "gpio20", "gpio21";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -116,7 +116,7 @@
 		pinconf {
 			pins = "gpio24", "gpio25";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -141,7 +141,7 @@
 		pinconf {
 			pins = "gpio8", "gpio9";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -166,7 +166,7 @@
 		pinconf {
 			pins = "gpio12", "gpio13";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -229,7 +229,23 @@
 		pinconf {
 			pins = "gpio16", "gpio17";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
+		};
+	};
+
+	gsbi4_uart_pin_a: gsbi4-uart-pin-active-state {
+		rx-pins {
+			pins = "gpio11";
+			function = "gsbi4";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		tx-pins {
+			pins = "gpio10";
+			function = "gsbi4";
+			drive-strength = <4>;
+			bias-disable;
 		};
 	};
 
@@ -282,7 +298,7 @@
 		pinconf {
 			pins = "gpio84", "gpio85";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
new file mode 100644
index 000000000000..2412aa3e3e8d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Sony Xperia Z";
+	compatible = "sony,xperia-yuga", "qcom,apq8064";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi5_uart_pin_a>;
+	status = "okay";
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio3", "gpio4", "gpio29", "gpio35";
+		function = "normal";
+
+		bias-pull-up;
+		drive-push-pull;
+		input-enable;
+		power-source = <2>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		qcom,pull-up-strength = <0>;
+	};
+};
+
+&riva {
+	pinctrl-names = "default";
+	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+
+	vddcx-supply = <&pm8921_s3>;
+	vddmx-supply = <&pm8921_l24>;
+	vddpx-supply = <&pm8921_s4>;
+
+	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8921_l4>;
+		vddrfa-supply = <&pm8921_s2>;
+		vddpa-supply = <&pm8921_l10>;
+		vdddig-supply = <&pm8921_lvs2>;
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs_1_3_6-supply = <&pm8921_s4>;
+		vin_lvs_4_5_7-supply = <&pm8921_s4>;
+		vin_ncp-supply = <&pm8921_l6>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_l24-supply = <&pm8921_s1>;
+		vin_l25-supply = <&pm8921_s1>;
+		vin_l27-supply = <&pm8921_s7>;
+		vin_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s8: s8 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		pm8921_l27: l27 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		pm8921_l28: l28 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l29: l29 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_usb_switch: usb-switch {};
+
+		pm8921_hdmi_switch: hdmi-switch {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
+
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	gsbi5_uart_pin_a: gsbi5-uart-pin-active {
+		rx {
+			pins = "gpio52";
+			function = "gsbi5";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		tx {
+			pins = "gpio51";
+			function = "gsbi5";
+			drive-strength = <4>;
+			bias-disable;
+		};
+	};
+
+
+	sdcc3_cd_pin_a: sdcc3-cd-pin-active {
+		pins = "gpio26";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi
index 46ed48f0244f..46ed48f0244f 100644
--- a/arch/arm/boot/dts/qcom-apq8064-v2.0.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 8b79b4112ee1..3faf57035d54 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -2,6 +2,7 @@
 /dts-v1/;
 
 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
 #include <dt-bindings/reset/qcom,gcc-msm8960.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8960.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
@@ -82,6 +83,7 @@
 		L2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 		};
 
 		idle-states {
@@ -95,17 +97,17 @@
 		};
 	};
 
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0>;
 	};
 
 	thermal-zones {
-		cpu-thermal0 {
+		cpu0-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 7>;
+			thermal-sensors = <&tsens 7>;
 			coefficients = <1199 0>;
 
 			trips {
@@ -122,11 +124,11 @@
 			};
 		};
 
-		cpu-thermal1 {
+		cpu1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 8>;
+			thermal-sensors = <&tsens 8>;
 			coefficients = <1132 0>;
 
 			trips {
@@ -143,11 +145,11 @@
 			};
 		};
 
-		cpu-thermal2 {
+		cpu2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 9>;
+			thermal-sensors = <&tsens 9>;
 			coefficients = <1199 0>;
 
 			trips {
@@ -164,11 +166,11 @@
 			};
 		};
 
-		cpu-thermal3 {
+		cpu3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 10>;
+			thermal-sensors = <&tsens 10>;
 			coefficients = <1132 0>;
 
 			trips {
@@ -198,7 +200,7 @@
 			clock-frequency = <19200000>;
 		};
 
-		pxo_board {
+		pxo_board: pxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
@@ -224,46 +226,6 @@
 		hwlocks = <&sfpb_mutex 3>;
 	};
 
-	smd {
-		compatible = "qcom,smd";
-
-		modem@0 {
-			interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&l2cc 8 3>;
-			qcom,smd-edge = <0>;
-
-			status = "disabled";
-		};
-
-		q6@1 {
-			interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&l2cc 8 15>;
-			qcom,smd-edge = <1>;
-
-			status = "disabled";
-		};
-
-		dsps@3 {
-			interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
-			qcom,smd-edge = <3>;
-
-			status = "disabled";
-		};
-
-		riva@6 {
-			interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&l2cc 8 25>;
-			qcom,smd-edge = <6>;
-
-			status = "disabled";
-		};
-	};
-
 	smsm {
 		compatible = "qcom,smsm";
 
@@ -315,30 +277,13 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-apq8064";
+			compatible = "qcom,scm-apq8064", "qcom,scm";
 
 			clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
 			clock-names = "core";
 		};
 	};
 
-
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&xoadc 0x00 0x01>, /* Battery */
-			    <&xoadc 0x00 0x02>, /* DC in (charger) */
-			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
-			    <&xoadc 0x00 0x0b>, /* Die temperature */
-			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			    <&xoadc 0x00 0x0e>; /* Charger temperature */
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -350,6 +295,7 @@
 			reg = <0x800000 0x4000>;
 
 			gpio-controller;
+			gpio-ranges = <&tlmm_pinmux 0 0 90>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -373,35 +319,50 @@
 		};
 
 		timer@200a000 {
-			compatible = "qcom,kpss-timer",
-				     "qcom,kpss-wdt-apq8064", "qcom,msm-timer";
+			compatible = "qcom,kpss-wdt-apq8064", "qcom,kpss-timer",
+				     "qcom,msm-timer";
 			interrupts = <1 1 0x301>,
 				     <1 2 0x301>,
 				     <1 3 0x301>;
 			reg = <0x0200a000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
+			clock-frequency = <27000000>;
 			cpu-offset = <0x80000>;
 		};
 
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
 		};
 
 		acc1: clock-controller@2098000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
 		};
 
 		acc2: clock-controller@20a8000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu2_aux";
+			#clock-cells = <0>;
 		};
 
 		acc3: clock-controller@20b8000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu3_aux";
+			#clock-cells = <0>;
 		};
 
 		saw0: power-controller@2089000 {
@@ -429,8 +390,8 @@
 		};
 
 		sps_sic_non_secure: sps-sic-non-secure@12100000 {
-			compatible	= "syscon";
-			reg		= <0x12100000 0x10000>;
+			compatible = "syscon";
+			reg = <0x12100000 0x10000>;
 		};
 
 		gsbi1: gsbi@12440000 {
@@ -537,6 +498,18 @@
 			#size-cells = <1>;
 			ranges;
 
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x100>,
+				      <0x16300000 0x3>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&gsbi4_uart_pin_a>;
+				pinctrl-names = "default";
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
 			gsbi4_i2c: i2c@16380000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
 				pinctrl-0 = <&i2c4_pins>;
@@ -665,168 +638,54 @@
 			clock-names = "core";
 		};
 
-		ssbi@c00000 {
+		ssbi2: ssbi@c00000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00c00000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8821: pmic@1 {
-				compatible = "qcom,pm8821";
-				interrupt-parent = <&tlmm_pinmux>;
-				interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8821_mpps: mpps@50 {
-					compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
-					reg = <0x50>;
-					interrupts = <24 IRQ_TYPE_NONE>,
-						     <25 IRQ_TYPE_NONE>,
-						     <26 IRQ_TYPE_NONE>,
-						     <27 IRQ_TYPE_NONE>;
-					gpio-controller;
-					#gpio-cells = <2>;
-				};
-			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pmicintc: pmic@0 {
-				compatible = "qcom,pm8921";
-				interrupt-parent = <&tlmm_pinmux>;
-				interrupts = <74 8>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8921_gpio: gpio@150 {
-
-					compatible = "qcom,pm8921-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8921_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8921_mpps: mpps@50 {
-					compatible = "qcom,pm8921-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					interrupts =
-					<128 IRQ_TYPE_NONE>,
-					<129 IRQ_TYPE_NONE>,
-					<130 IRQ_TYPE_NONE>,
-					<131 IRQ_TYPE_NONE>,
-					<132 IRQ_TYPE_NONE>,
-					<133 IRQ_TYPE_NONE>,
-					<134 IRQ_TYPE_NONE>,
-					<135 IRQ_TYPE_NONE>,
-					<136 IRQ_TYPE_NONE>,
-					<137 IRQ_TYPE_NONE>,
-					<138 IRQ_TYPE_NONE>,
-					<139 IRQ_TYPE_NONE>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <39 1>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				xoadc: xoadc@197 {
-					compatible = "qcom,pm8921-adc";
-					reg = <197>;
-					interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@00 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@01 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@02 {
-						reg = <0x00 0x02>;
-					};
-					vph_pwr: adc-channel@04 {
-						reg = <0x00 0x04>;
-					};
-					batt_therm: adc-channel@08 {
-						reg = <0x00 0x08>;
-					};
-					batt_id: adc-channel@09 {
-						reg = <0x00 0x09>;
-					};
-					usb_vbus: adc-channel@0a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@0b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@0c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@0d {
-						reg = <0x00 0x0d>;
-					};
-					chg_temp: adc-channel@0e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@0f {
-						reg = <0x00 0x0f>;
-					};
-				};
-			};
 		};
 
 		qfprom: qfprom@700000 {
-			compatible	= "qcom,qfprom";
-			reg		= <0x00700000 0x1000>;
-			#address-cells	= <1>;
-			#size-cells	= <1>;
+			compatible = "qcom,apq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			ranges;
-			tsens_calib: calib {
+			tsens_calib: calib@404 {
 				reg = <0x404 0x10>;
 			};
-			tsens_backup: backup_calib {
+			tsens_backup: backup_calib@414 {
 				reg = <0x414 0x10>;
 			};
 		};
 
 		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-apq8064";
+			compatible = "qcom,gcc-apq8064", "syscon";
 			reg = <0x00900000 0x4000>;
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
-			#thermal-sensor-cells = <1>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
+
+			tsens: thermal-sensor {
+				compatible = "qcom,msm8960-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
 		};
 
 		lcc: clock-controller@28000000 {
@@ -834,87 +693,69 @@
 			reg = <0x28000000 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
 		};
 
 		mmcc: clock-controller@4000000 {
 			compatible = "qcom,mmcc-apq8064";
 			reg = <0x4000000 0x1000>;
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <&dsi0_phy 1>,
+				 <&dsi0_phy 0>,
+				 <&dsi1_phy 1>,
+				 <&dsi1_phy 0>,
+				 <&hdmi_phy>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
 		};
 
 		l2cc: clock-controller@2011000 {
-			compatible	= "syscon";
-			reg		= <0x2011000 0x1000>;
+			compatible = "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
 		};
 
-		rpm@108000 {
-			compatible	= "qcom,rpm-apq8064";
-			reg		= <0x108000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-apq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
 
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 
 			rpmcc: clock-controller {
-				compatible	= "qcom,rpmcc-apq8064", "qcom,rpmcc";
+				compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc";
 				#clock-cells = <1>;
-			};
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-
-				pm8921_s1: s1 {};
-				pm8921_s2: s2 {};
-				pm8921_s3: s3 {};
-				pm8921_s4: s4 {};
-				pm8921_s7: s7 {};
-				pm8921_s8: s8 {};
-
-				pm8921_l1: l1 {};
-				pm8921_l2: l2 {};
-				pm8921_l3: l3 {};
-				pm8921_l4: l4 {};
-				pm8921_l5: l5 {};
-				pm8921_l6: l6 {};
-				pm8921_l7: l7 {};
-				pm8921_l8: l8 {};
-				pm8921_l9: l9 {};
-				pm8921_l10: l10 {};
-				pm8921_l11: l11 {};
-				pm8921_l12: l12 {};
-				pm8921_l14: l14 {};
-				pm8921_l15: l15 {};
-				pm8921_l16: l16 {};
-				pm8921_l17: l17 {};
-				pm8921_l18: l18 {};
-				pm8921_l21: l21 {};
-				pm8921_l22: l22 {};
-				pm8921_l23: l23 {};
-				pm8921_l24: l24 {};
-				pm8921_l25: l25 {};
-				pm8921_l26: l26 {};
-				pm8921_l27: l27 {};
-				pm8921_l28: l28 {};
-				pm8921_l29: l29 {};
-
-				pm8921_lvs1: lvs1 {};
-				pm8921_lvs2: lvs2 {};
-				pm8921_lvs3: lvs3 {};
-				pm8921_lvs4: lvs4 {};
-				pm8921_lvs5: lvs5 {};
-				pm8921_lvs6: lvs6 {};
-				pm8921_lvs7: lvs7 {};
-
-				pm8921_usb_switch: usb-switch {};
-
-				pm8921_hdmi_switch: hdmi-switch {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {};
+				clocks = <&pxo_board>, <&cxo_board>;
+				clock-names = "pxo", "cxo";
 			};
 		};
 
@@ -1012,53 +853,59 @@
 		};
 
 		sata_phy0: phy@1b400000 {
-			compatible	= "qcom,apq8064-sata-phy";
-			status		= "disabled";
-			reg		= <0x1b400000 0x200>;
-			reg-names	= "phy_mem";
-			clocks		= <&gcc SATA_PHY_CFG_CLK>;
-			clock-names	= "cfg";
-			#phy-cells	= <0>;
+			compatible = "qcom,apq8064-sata-phy";
+			status = "disabled";
+			reg = <0x1b400000 0x200>;
+			reg-names = "phy_mem";
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+			#phy-cells = <0>;
 		};
 
 		sata0: sata@29000000 {
-			compatible		= "qcom,apq8064-ahci", "generic-ahci";
-			status			= "disabled";
-			reg			= <0x29000000 0x180>;
-			interrupts		= <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
-			clocks			= <&gcc SFAB_SATA_S_H_CLK>,
-						<&gcc SATA_H_CLK>,
-						<&gcc SATA_A_CLK>,
-						<&gcc SATA_RXOOB_CLK>,
-						<&gcc SATA_PMALIVE_CLK>;
-			clock-names		= "slave_iface",
-						"iface",
-						"bus",
-						"rxoob",
-						"core_pmalive";
-
-			assigned-clocks		= <&gcc SATA_RXOOB_CLK>,
-						<&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates	= <100000000>, <100000000>;
-
-			phys			= <&sata_phy0>;
-			phy-names		= "sata-phy";
-			ports-implemented	= <0x1>;
-		};
-
-		/* Temporary fixed regulator */
-		sdcc1bam:dma@12402000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc3bam:dma@12182000{
+			compatible = "qcom,apq8064-ahci", "generic-ahci";
+			status	 = "disabled";
+			reg	 = <0x29000000 0x180>;
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_iface",
+				      "iface",
+				      "bus",
+				      "rxoob",
+				      "core_pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>,
+					  <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy0>;
+			phy-names = "sata-phy";
+			ports-implemented = <0x1>;
+		};
+
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x12182000 0x8000>;
 			interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
@@ -1068,7 +915,25 @@
 			qcom,ee = <0>;
 		};
 
-		sdcc4bam:dma@121c2000{
+		sdcc4: mmc@121c0000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x121c0000 0x2000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdc4_gpios>;
+		};
+
+		sdcc4bam: dma-controller@121c2000 {
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x121c2000 0x8000>;
 			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
@@ -1078,67 +943,33 @@
 			qcom,ee = <0>;
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: sdcc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
-				pinctrl-names	= "default";
-				pinctrl-0	= <&sdcc1_pins>;
-				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x2000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc3: sdcc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x2000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency	= <192000000>;
-				no-1-8-v;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc4: sdcc@121c0000 {
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x121c0000 0x2000>;
-				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
-				dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
-				dma-names = "tx", "rx";
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdc4_gpios>;
-			};
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdcc1_pins>;
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
 		};
 
 		tcsr: syscon@1a400000 {
@@ -1147,22 +978,21 @@
 		};
 
 		gpu: adreno-3xx@4300000 {
-			compatible = "qcom,adreno-3xx";
+			compatible = "qcom,adreno-320.2", "qcom,adreno";
 			reg = <0x04300000 0x20000>;
 			reg-names = "kgsl_3d0_reg_memory";
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "kgsl_3d0_irq";
 			clock-names =
-			    "core_clk",
-			    "iface_clk",
-			    "mem_clk",
-			    "mem_iface_clk";
+			    "core",
+			    "iface",
+			    "mem",
+			    "mem_iface";
 			clocks =
 			    <&mmcc GFX3D_CLK>,
 			    <&mmcc GFX3D_AHB_CLK>,
 			    <&mmcc GFX3D_AXI_CLK>,
 			    <&mmcc MMSS_IMEM_AHB_CLK>;
-			qcom,chipid = <0x03020002>;
 
 			iommus = <&gfx3d 0
 				  &gfx3d 1
@@ -1229,13 +1059,17 @@
 				  &gfx3d1 30
 				  &gfx3d1 31>;
 
-			qcom,gpu-pwrlevels {
-				compatible = "qcom,gpu-pwrlevels";
-				qcom,gpu-pwrlevel@0 {
-					qcom,gpu-freq = <450000000>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-450000000 {
+					opp-hz = /bits/ 64 <450000000>;
 				};
-				qcom,gpu-pwrlevel@1 {
-					qcom,gpu-freq = <27000000>;
+
+				opp-27000000 {
+					opp-hz = /bits/ 64 <27000000>;
 				};
 			};
 		};
@@ -1245,9 +1079,9 @@
 			reg = <0x5700000 0x70>;
 		};
 
-		dsi0: mdss_dsi@4700000 {
-			compatible = "qcom,mdss-dsi-ctrl";
-			label = "MDSS DSI CTRL->0";
+		dsi0: dsi@4700000 {
+			compatible = "qcom,apq8064-dsi-ctrl",
+				     "qcom,mdss-dsi-ctrl";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -1261,9 +1095,9 @@
 				<&mmcc DSI1_BYTE_CLK>,
 				<&mmcc DSI_PIXEL_CLK>,
 				<&mmcc DSI1_ESC_CLK>;
-			clock-names = "iface_clk", "bus_clk", "core_mmss_clk",
-					"src_clk", "byte_clk", "pixel_clk",
-					"core_clk";
+			clock-names = "iface", "bus", "core_mmss",
+					"src", "byte", "pixel",
+					"core";
 
 			assigned-clocks = <&mmcc DSI1_BYTE_SRC>,
 					<&mmcc DSI1_ESC_SRC>,
@@ -1275,6 +1109,8 @@
 						<&dsi0_phy 1>;
 			syscon-sfpb = <&mmss_sfpb>;
 			phys = <&dsi0_phy>;
+			status = "disabled";
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1294,7 +1130,7 @@
 		};
 
 
-		dsi0_phy: dsi-phy@4700200 {
+		dsi0_phy: phy@4700200 {
 			compatible = "qcom,dsi-phy-28nm-8960";
 			#clock-cells = <1>;
 			#phy-cells = <0>;
@@ -1303,11 +1139,86 @@
 				<0x04700300 0x200>,
 				<0x04700500 0x5c>;
 			reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
-			clock-names = "iface_clk", "ref";
+			clock-names = "iface", "ref";
 			clocks = <&mmcc DSI_M_AHB_CLK>,
-				 <&cxo_board>;
+				 <&pxo_board>;
+			status = "disabled";
 		};
 
+		dsi1: dsi@5800000 {
+			compatible = "qcom,mdss-dsi-ctrl";
+			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x05800000 0x200>;
+			reg-names = "dsi_ctrl";
+
+			clocks = <&mmcc DSI2_M_AHB_CLK>,
+				 <&mmcc DSI2_S_AHB_CLK>,
+				 <&mmcc AMP_AHB_CLK>,
+				 <&mmcc DSI2_CLK>,
+				 <&mmcc DSI2_BYTE_CLK>,
+				 <&mmcc DSI2_PIXEL_CLK>,
+				 <&mmcc DSI2_ESC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "core_mmss",
+				      "src",
+				      "byte",
+				      "pixel",
+				      "core";
+
+			assigned-clocks = <&mmcc DSI2_BYTE_SRC>,
+					  <&mmcc DSI2_ESC_SRC>,
+					  <&mmcc DSI2_SRC>,
+					  <&mmcc DSI2_PIXEL_SRC>;
+			assigned-clock-parents = <&dsi1_phy 0>,
+						 <&dsi1_phy 0>,
+						 <&dsi1_phy 1>,
+						 <&dsi1_phy 1>;
+
+			syscon-sfpb = <&mmss_sfpb>;
+			phys = <&dsi1_phy>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi1_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dsi1_out: endpoint {
+					};
+				};
+			};
+		};
+
+
+		dsi1_phy: dsi-phy@5800200 {
+			compatible = "qcom,dsi-phy-28nm-8960";
+			reg = <0x05800200 0x100>,
+			      <0x05800300 0x200>,
+			      <0x05800500 0x5c>;
+			reg-names = "dsi_pll",
+				    "dsi_phy",
+				    "dsi_phy_regulator";
+			clock-names = "iface",
+				      "ref";
+			clocks = <&mmcc DSI2_M_AHB_CLK>,
+				 <&pxo_board>;
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
 
 		mdp_port0: iommu@7500000 {
 			compatible = "qcom,apq8064-iommu";
@@ -1373,12 +1284,12 @@
 			qcom,ncb = <3>;
 		};
 
-		pcie: pci@1b500000 {
-			compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
-			reg = <0x1b500000 0x1000
-			       0x1b502000 0x80
-			       0x1b600000 0x100
-			       0x0ff00000 0x100000>;
+		pcie: pcie@1b500000 {
+			compatible = "qcom,pcie-apq8064";
+			reg = <0x1b500000 0x1000>,
+			      <0x1b502000 0x80>,
+			      <0x1b600000 0x100>,
+			      <0x0ff00000 0x100000>;
 			reg-names = "dbi", "elbi", "parf", "config";
 			device_type = "pci";
 			linux,pci-domain = <0>;
@@ -1386,8 +1297,8 @@
 			num-lanes = <1>;
 			#address-cells = <3>;
 			#size-cells = <2>;
-			ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000   /* I/O */
-				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* memory */
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00100000>, /* I/O */
+				 <0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* mem */
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
@@ -1419,12 +1330,13 @@
 			clocks = <&mmcc HDMI_APP_CLK>,
 				 <&mmcc HDMI_M_AHB_CLK>,
 				 <&mmcc HDMI_S_AHB_CLK>;
-			clock-names = "core_clk",
-				      "master_iface_clk",
-				      "slave_iface_clk";
+			clock-names = "core",
+				      "master_iface",
+				      "slave_iface";
 
 			phys = <&hdmi_phy>;
-			phy-names = "hdmi-phy";
+
+			status = "disabled";
 
 			ports {
 				#address-cells = <1>;
@@ -1444,7 +1356,7 @@
 			};
 		};
 
-		hdmi_phy: hdmi-phy@4a00400 {
+		hdmi_phy: phy@4a00400 {
 			compatible = "qcom,hdmi-phy-8960";
 			reg = <0x4a00400 0x60>,
 			      <0x4a00500 0x100>;
@@ -1452,11 +1364,14 @@
 				    "hdmi_pll";
 
 			clocks = <&mmcc HDMI_S_AHB_CLK>;
-			clock-names = "slave_iface_clk";
+			clock-names = "slave_iface";
 			#phy-cells = <0>;
+			#clock-cells = <0>;
+
+			status = "disabled";
 		};
 
-		mdp: mdp@5100000 {
+		mdp: display-controller@5100000 {
 			compatible = "qcom,mdp4";
 			reg = <0x05100000 0xf0000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -1508,7 +1423,7 @@
 			};
 		};
 
-		riva: riva-pil@3204000 {
+		riva: riva-pil@3200800 {
 			compatible = "qcom,riva-pil";
 
 			reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
@@ -1520,10 +1435,6 @@
 
 			memory-region = <&wcnss_mem>;
 
-			vddcx-supply = <&pm8921_s3>;
-			vddmx-supply = <&pm8921_l24>;
-			vddpx-supply = <&pm8921_s4>;
-
 			status = "disabled";
 
 			iris {
@@ -1531,11 +1442,6 @@
 
 				clocks = <&cxo_board>;
 				clock-names = "xo";
-
-				vddxo-supply = <&pm8921_l4>;
-				vddrfa-supply = <&pm8921_s2>;
-				vddpa-supply = <&pm8921_l10>;
-				vdddig-supply = <&pm8921_lvs2>;
 			};
 
 			smd-edge {
@@ -1552,7 +1458,7 @@
 
 					qcom,mmio = <&riva>;
 
-					bt {
+					bluetooth {
 						compatible = "qcom,wcnss-bt";
 					};
 
@@ -1571,7 +1477,7 @@
 		};
 
 		etb@1a01000 {
-			compatible = "coresight-etb10", "arm,primecell";
+			compatible = "arm,coresight-etb10", "arm,primecell";
 			reg = <0x1a01000 0x1000>;
 
 			clocks = <&rpmcc RPM_QDSS_CLK>;
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
new file mode 100644
index 000000000000..6fce0112361f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
@@ -0,0 +1,492 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+
+/delete-node/ &mpss_region;
+
+/ {
+	model = "Qualcomm APQ8074 Dragonboard";
+	compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		usid0 = &pm8941_0;
+		usid4 = &pm8841_0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-0 = <&msm_keys_default>;
+		pinctrl-names = "default";
+
+		button-volup {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-general {
+			label = "General";
+			linux,code = <KEY_PROG1>;
+			gpios = <&pm8941_gpios 23 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reserved-memory {
+		mpss_region: mpss@ac00000 {
+			reg = <0x0ac00000 0x2500000>;
+			no-map;
+		};
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <200000>;
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+		read-only;
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_l22>;
+	vddio-supply = <&pm8941_l12>;
+
+	status = "okay";
+
+	panel: panel@0 {
+		compatible = "sharp,ls043t1le01-qhd";
+		reg = <0>;
+
+		avdd-supply = <&pm8941_l22>;
+		backlight = <&pm8941_wled>;
+		reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pm8941_l12>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&pm8941_gpios {
+        msm_keys_default: pm8941-gpio-keys-state {
+		pins = "gpio5", "gpio23";
+		function = "normal";
+		input-enable;
+		drive-push-pull;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		power-source = <PM8941_GPIO_S3>; /* 1.8V */
+        };
+};
+
+&pm8941_lpg {
+	qcom,power-source = <1>;
+	status = "okay";
+
+	led@5 {
+		reg = <5>;
+		color = <LED_COLOR_ID_BLUE>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+
+	led@6 {
+		reg = <6>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+
+	led@7 {
+		reg = <7>;
+		color = <LED_COLOR_ID_RED>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+};
+
+&pm8941_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8941_wled {
+	qcom,cs-out;
+	qcom,switching-freq = <3200>;
+	qcom,ovp = <32>;
+	qcom,num-strings = <1>;
+
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+
+	firmware-name = "qcom/apq8074/adsp.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+
+	firmware-name = "qcom/apq8074/mba.mbn", "qcom/apq8074/modem.mbn";
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vin_5vs-supply = <&pm8941_5v>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	status = "okay";
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs2_phy>;
+	phy-select = <&tcsr 0xb000 1>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs2_phy {
+	status = "okay";
+	v3p3-supply = <&pm8941_l24>;
+	v1p8-supply = <&pm8941_l6>;
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x63>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
index 44cd72f1b1be..1df24c922be9 100644
--- a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8084.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 
 / {
 	model = "Qualcomm APQ8084/IFC6540";
@@ -19,16 +19,16 @@
 		serial@f995e000 {
 			status = "okay";
 		};
+	};
+};
 
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "okay";
-		};
+&sdhc_1 {
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
 
-		sdhci@f98a4900 {
-			cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
-			bus-width = <4>;
-		};
-	};
+&sdhc_2 {
+	cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
 };
diff --git a/arch/arm/boot/dts/qcom-apq8084-mtp.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
index c6b6680248a6..d4e6aee034af 100644
--- a/arch/arm/boot/dts/qcom-apq8084-mtp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8084.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 
 / {
 	model = "Qualcomm APQ 8084-MTP";
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
index 0a0fb147ebb9..2b1f9d0fb510 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-apq8084.h>
 #include <dt-bindings/gpio/gpio.h>
 
@@ -71,8 +72,9 @@
 		};
 
 		L2: l2-cache {
-			compatible = "qcom,arch-cache";
+			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 			qcom,saw = <&saw_l2>;
 		};
 
@@ -94,14 +96,14 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm";
+			compatible = "qcom,scm-apq8084", "qcom,scm";
 			clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
 			clock-names = "core", "bus", "iface";
 		};
 	};
 
 	thermal-zones {
-		cpu-thermal0 {
+		cpu0-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -121,7 +123,7 @@
 			};
 		};
 
-		cpu-thermal1 {
+		cpu1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -141,7 +143,7 @@
 			};
 		};
 
-		cpu-thermal2 {
+		cpu2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -161,7 +163,7 @@
 			};
 		};
 
-		cpu-thermal3 {
+		cpu3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -184,7 +186,7 @@
 
 	cpu-pmu {
 		compatible = "qcom,krait-pmu";
-		interrupts = <1 7 0xf04>;
+		interrupts = <GIC_PPI 7 0xf04>;
 	};
 
 	clocks {
@@ -203,10 +205,10 @@
 
 	timer {
 		compatible = "arm,armv7-timer";
-		interrupts = <1 2 0xf08>,
-			     <1 3 0xf08>,
-			     <1 4 0xf08>,
-			     <1 1 0xf08>;
+		interrupts = <GIC_PPI 2 0xf08>,
+			     <GIC_PPI 3 0xf08>,
+			     <GIC_PPI 4 0xf08>,
+			     <GIC_PPI 1 0xf08>;
 		clock-frequency = <19200000>;
 	};
 
@@ -238,27 +240,336 @@
 			reg = <0xf9011000 0x1000>;
 		};
 
+		sram@fc190000 {
+			compatible = "qcom,apq8084-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
 		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,apq8084-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			compatible = "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
-			tsens_calib: calib@d0 {
-				reg = <0xd0 0x18>;
+
+			tsens_base1: base1@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1: s0-p1@d1 {
+				reg = <0xd1 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1: s1-p1@d2 {
+				reg = <0xd1 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1: s2-p1@d2 {
+				reg = <0xd2 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1: s3-p1@d3 {
+				reg = <0xd3 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1: s4-p1@d4 {
+				reg = <0xd4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1: s5-p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@d5 {
+				reg = <0xd5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1: s7-p1@d6 {
+				reg = <0xd6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s8_p1: s8-p1@d7 {
+				reg = <0xd7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_mode: mode@d7 {
+				reg = <0xd7 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s9_p1: s9-p1@d8 {
+				reg = <0xd8 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s10_p1: s10_p1@d8 {
+				reg = <0xd8 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_base2: base2@d9 {
+				reg = <0xd9 0x2>;
+				bits = <4 8>;
+			};
+
+			tsens_s0_p2: s0-p2@da {
+				reg = <0xda 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s1_p2: s1-p2@db {
+				reg = <0xdb 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s2_p2: s2-p2@dc {
+				reg = <0xdc 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s3_p2: s3-p2@dc {
+				reg = <0xdc 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s4_p2: s4-p2@dd {
+				reg = <0xdd 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@de {
+				reg = <0xde 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@df {
+				reg = <0xdf 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@e0 {
+				reg = <0xe0 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s8_p2: s8-p2@e0 {
+				reg = <0xe0 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s9_p2: s9-p2@e1 {
+				reg = <0xe1 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s10_p2: s10_p2@e2 {
+				reg = <0xe2 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p2_backup: s5-p2_backup@e3 {
+				reg = <0xe3 0x2>;
+				bits = <0 6>;
 			};
-			tsens_backup: backup@440 {
-				reg = <0x440 0x10>;
+
+			tsens_mode_backup: mode_backup@e3 {
+				reg = <0xe3 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s6_p2_backup: s6-p2_backup@e4 {
+				reg = <0xe4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2_backup: s7-p2_backup@e4 {
+				reg = <0xe4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p2_backup: s8-p2_backup@e5 {
+				reg = <0xe5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s9_p2_backup: s9-p2_backup@e6 {
+				reg = <0xe6 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s10_p2_backup: s10_p2_backup@e7 {
+				reg = <0xe7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_base1_backup: base1_backup@440 {
+				reg = <0x440 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1_backup: s0-p1_backup@441 {
+				reg = <0x441 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1_backup: s1-p1_backup@442 {
+				reg = <0x441 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1_backup: s2-p1_backup@442 {
+				reg = <0x442 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1_backup: s3-p1_backup@443 {
+				reg = <0x443 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1_backup: s4-p1_backup@444 {
+				reg = <0x444 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1_backup: s5-p1_backup@444 {
+				reg = <0x444 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1_backup: s6-p1_backup@445 {
+				reg = <0x445 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1_backup: s7-p1_backup@446 {
+				reg = <0x446 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_use_backup: use_backup@447 {
+				reg = <0x447 0x1>;
+				bits = <5 3>;
+			};
+
+			tsens_s8_p1_backup: s8-p1_backup@448 {
+				reg = <0x448 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p1_backup: s9-p1_backup@448 {
+				reg = <0x448 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s10_p1_backup: s10_p1_backup@449 {
+				reg = <0x449 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2_backup: base2_backup@44a {
+				reg = <0x44a 0x2>;
+				bits = <2 8>;
+			};
+
+			tsens_s0_p2_backup: s0-p2_backup@44b {
+				reg = <0x44b 0x3>;
+				bits = <2 6>;
+			};
+
+			tsens_s1_p2_backup: s1-p2_backup@44c {
+				reg = <0x44c 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p2_backup: s2-p2_backup@44c {
+				reg = <0x44c 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p2_backup: s3-p2_backup@44d {
+				reg = <0x44d 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p2_backup: s4-p2_backup@44e {
+				reg = <0x44e 0x1>;
+				bits = <2 6>;
 			};
 		};
 
-		tsens: thermal-sensor@fc4a8000 {
-			compatible = "qcom,msm8974-tsens";
-			reg = <0xfc4a8000 0x2000>;
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_use_backup>,
+				      <&tsens_mode_backup>,
+				      <&tsens_base1_backup>, <&tsens_base2_backup>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>,
+				      <&tsens_s10_p1>, <&tsens_s10_p2>,
+				      <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
+				      <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
+				      <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
+				      <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
+				      <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
+				      <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
+				      <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
+				      <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
+				      <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
+				      <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
+				      <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "use_backup",
+					   "mode_backup",
+					   "base1_backup", "base2_backup",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2",
+					   "s10_p1", "s10_p2",
+					   "s0_p1_backup", "s0_p2_backup",
+					   "s1_p1_backup", "s1_p2_backup",
+					   "s2_p1_backup", "s2_p2_backup",
+					   "s3_p1_backup", "s3_p2_backup",
+					   "s4_p1_backup", "s4_p2_backup",
+					   "s5_p1_backup", "s5_p2_backup",
+					   "s6_p1_backup", "s6_p2_backup",
+					   "s7_p1_backup", "s7_p2_backup",
+					   "s8_p1_backup", "s8_p2_backup",
+					   "s9_p1_backup", "s9_p2_backup",
+					   "s10_p1_backup", "s10_p2_backup";
+			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
 			#thermal-sensor-cells = <1>;
 		};
-
 		timer@f9020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -269,50 +580,50 @@
 
 			frame@f9021000 {
 				frame-number = <0>;
-				interrupts = <0 8 0x4>,
-					     <0 7 0x4>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9021000 0x1000>,
 				      <0xf9022000 0x1000>;
 			};
 
 			frame@f9023000 {
 				frame-number = <1>;
-				interrupts = <0 9 0x4>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9023000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@f9024000 {
 				frame-number = <2>;
-				interrupts = <0 10 0x4>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9024000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@f9025000 {
 				frame-number = <3>;
-				interrupts = <0 11 0x4>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9025000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@f9026000 {
 				frame-number = <4>;
-				interrupts = <0 12 0x4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9026000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@f9027000 {
 				frame-number = <5>;
-				interrupts = <0 13 0x4>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9027000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@f9028000 {
 				frame-number = <6>;
-				interrupts = <0 14 0x4>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0xf9028000 0x1000>;
 				status = "disabled";
 			};
@@ -344,25 +655,25 @@
 			regulator;
 		};
 
-		acc0: clock-controller@f9088000 {
+		acc0: power-manager@f9088000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf9088000 0x1000>,
 			      <0xf9008000 0x1000>;
 		};
 
-		acc1: clock-controller@f9098000 {
+		acc1: power-manager@f9098000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf9098000 0x1000>,
 			      <0xf9008000 0x1000>;
 		};
 
-		acc2: clock-controller@f90a8000 {
+		acc2: power-manager@f90a8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf90a8000 0x1000>,
 			      <0xf9008000 0x1000>;
 		};
 
-		acc3: clock-controller@f90b8000 {
+		acc3: power-manager@f90b8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf90b8000 0x1000>,
 			      <0xf9008000 0x1000>;
@@ -379,20 +690,33 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0xfc400000 0x4000>;
-		};
-
-		tcsr_mutex_regs: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
-
-		tcsr_mutex: hwlock {
-			compatible = "qcom,tcsr-mutex";
-			syscon = <&tcsr_mutex_regs 0 0x80>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <0>, /* ufs */
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>, /* sata */
+				 <0>,
+				 <0>; /* pcie */
+			clock-names = "xo",
+				      "sleep_clk",
+				      "ufs_rx_symbol_0_clk_src",
+				      "ufs_rx_symbol_1_clk_src",
+				      "ufs_tx_symbol_0_clk_src",
+				      "ufs_tx_symbol_1_clk_src",
+				      "sata_asic0_clk",
+				      "sata_rx_clk",
+				      "pcie_pipe";
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,apq8084-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
 			#hwlock-cells = <1>;
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
@@ -401,44 +725,45 @@
 			compatible = "qcom,apq8084-pinctrl";
 			reg = <0xfd510000 0x4000>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 147>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
-			interrupts = <0 208 0>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		blsp2_uart2: serial@f995e000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xf995e000 0x1000>;
-			interrupts = <0 114 0x0>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
 			clock-names = "core", "iface";
 			status = "disabled";
 		};
 
-		sdhci@f9824900 {
+		sdhc_1: mmc@f9824900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <0 123 0>, <0 138 0>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
-		sdhci@f98a4900 {
+		sdhc_2: mmc@f98a4900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <0 125 0>, <0 221 0>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
@@ -449,7 +774,7 @@
 			      <0xfc4cb000 0x1000>,
 			      <0xfc4ca000 0x1000>;
 			interrupt-names = "periph_irq";
-			interrupts = <0 190 0>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;
@@ -459,19 +784,19 @@
 		};
 	};
 
-	smd {
-		compatible = "qcom,smd";
+	rpm: remoteproc {
+		compatible = "qcom,apq8084-rpm-proc", "qcom,rpm-proc";
 
-		rpm {
-			interrupts = <0 168 1>;
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
 			qcom,ipc = <&apcs 8 0>;
 			qcom,smd-edge = <15>;
 
-			rpm_requests {
+			rpm-requests {
 				compatible = "qcom,rpm-apq8084";
 				qcom,smd-channels = "rpm_requests";
 
-				pma8084-regulators {
+				regulators-0 {
 					compatible = "qcom,rpm-pma8084-regulators";
 
 					pma8084_s1: s1 {};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts
new file mode 100644
index 000000000000..1b27edce9d4f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/leds/common.h>
+#include "qcom-ipq4018-ap120c-ac.dtsi"
+
+/ {
+	model = "ALFA Network AP120C-AC Bit";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "ap120c-ac:green:power";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led-wlan {
+			label = "ap120c-ac:green:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-support {
+			label = "ap120c-ac:green:support";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts
new file mode 100644
index 000000000000..a707057c887d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/leds/common.h>
+#include "qcom-ipq4018-ap120c-ac.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+
+		status: led-status {
+			label = "ap120c-ac:blue:status";
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		led-wlan2g {
+			label = "ap120c-ac:green:wlan2g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		led-wlan5g {
+			label = "ap120c-ac:red:wlan5g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi
new file mode 100644
index 000000000000..da67d55fa557
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ALFA Network AP120C-AC";
+	compatible = "alfa-network,ap120c-ac", "qcom,ipq4018";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&tlmm {
+	i2c0_pins: i2c0_pinmux {
+		mux_i2c {
+			function = "blsp_i2c0";
+			pins = "gpio58", "gpio59";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_mdio {
+			pins = "gpio53";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_mdc {
+			pins = "gpio52";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial0_pins: serial0_pinmux {
+		mux_uart {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi0_pins: spi0_pinmux {
+		mux_spi {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		mux_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio4";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	usb-power-hog {
+		line-name = "USB-power";
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		gpio-hog;
+		output-high;
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&prng {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	tpm@29 {
+		compatible = "atmel,at97sc3204t";
+		reg = <0x29>;
+	};
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "u-boot-env";
+				reg = <0x000e0000 0x00010000>;
+			};
+
+			partition@f0000 {
+				label = "u-boot";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				precal_art_1000: precal@1000 {
+					reg = <0x1000 0x2f20>;
+				};
+
+				precal_art_5000: precal@5000 {
+					reg = <0x5000 0x2f20>;
+				};
+			};
+
+			partition@180000 {
+				label = "priv_data1";
+				reg = <0x00180000 0x00010000>;
+				read-only;
+			};
+
+			partition@190000 {
+				label = "priv_data2";
+				reg = <0x00190000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+
+	flash@1 {
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ubi1";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "ubi2";
+				reg = <0x04000000 0x04000000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial0_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+};
+
+&wifi0 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_1000>;
+};
+
+&wifi1 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_5000>;
+	qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+
+	};
+
+&usb3_dwc {
+	phys = <&usb3_hs_phy>;
+	phy-names = "usb2-phy";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts
new file mode 100644
index 000000000000..365fbac417fd
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2018, Robert Marko <robimarko@gmail.com>
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "8devices Jalapeno";
+	compatible = "8dev,jalapeno", "qcom,ipq4018";
+};
+
+&tlmm {
+	mdio_pins: mdio_pinmux {
+		pinmux_1 {
+			pins = "gpio53";
+			function = "mdio";
+		};
+
+		pinmux_2 {
+			pins = "gpio52";
+			function = "mdc";
+		};
+
+		pinconf {
+			pins = "gpio52", "gpio53";
+			bias-pull-up;
+		};
+	};
+
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pin {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		pin_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio59";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&prng {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		status = "okay";
+
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "u-boot-env";
+				reg = <0x000e0000 0x00010000>;
+			};
+
+			partition@f0000 {
+				label = "u-boot";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+
+	spi-nand@1 {
+		status = "okay";
+
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ubi1";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "ubi2";
+				reg = <0x04000000 0x04000000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+};
+
+&wifi0 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&wifi1 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts
index 0d92f1bc3a13..ddaa273f72ca 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts
@@ -18,5 +18,5 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1";
-
+	compatible = "qcom,ipq4019-ap-dk01.1-c1", "qcom,ipq4019";
 };
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi
index 418f9a022336..0505270cf508 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi
@@ -14,11 +14,11 @@
  *
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include "qcom-ipq4019.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1";
-	compatible = "qcom,ipq4019";
 
 	aliases {
 		serial0 = &blsp1_uart1;
@@ -30,7 +30,7 @@
 
 	soc {
 		rng@22000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		pinctrl@1000000 {
@@ -65,15 +65,15 @@
 			};
 		};
 
-		blsp_dma: dma@7884000 {
-			status = "ok";
+		blsp_dma: dma-controller@7884000 {
+			status = "okay";
 		};
 
 		spi@78b5000 {
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
-			status = "ok";
-			cs-gpios = <&tlmm 54 0>;
+			status = "okay";
+			cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
 
 			mx25l25635e@0 {
 				#address-cells = <1>;
@@ -87,27 +87,27 @@
 		serial@78af000 {
 			pinctrl-0 = <&serial_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 
-		cryptobam: dma@8e04000 {
-			status = "ok";
+		cryptobam: dma-controller@8e04000 {
+			status = "okay";
 		};
 
 		crypto@8e3a000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		watchdog@b017000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		wifi@a000000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		wifi@a800000 {
-			status = "ok";
+			status = "okay";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts
index 7a96f300bc8d..0993f840d1fc 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts
@@ -5,15 +5,15 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C1";
-	compatible = "qcom,ipq4019-dk04.1-c1";
+	compatible = "qcom,ipq4019-dk04.1-c1", "qcom,ipq4019";
 
 	soc {
-		dma@7984000 {
-			status = "ok";
-		};
-
-		qpic-nand@79b0000 {
-			status = "ok";
+		dma-controller@7984000 {
+			status = "okay";
 		};
 	};
 };
+
+&nand {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts
index 2d1c4c6e42f1..7765247125e4 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts
@@ -5,5 +5,5 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C3";
-	compatible = "qcom,ipq4019-ap-dk04.1-c3";
+	compatible = "qcom,ipq4019-ap-dk04.1-c3", "qcom,ipq4019";
 };
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi
index 7c1eb1963c67..374af6dd360a 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi
@@ -70,42 +70,42 @@
 		serial@78af000 {
 			pinctrl-0 = <&serial_0_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 
 		serial@78b0000 {
 			pinctrl-0 = <&serial_1_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 
-		dma@7884000 {
-			status = "ok";
+		dma-controller@7884000 {
+			status = "okay";
 		};
 
 		spi@78b5000 { /* BLSP1 QUP1 */
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
-			status = "ok";
-			cs-gpios = <&tlmm 12 0>;
+			status = "okay";
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0>;
-				compatible = "n25q128a11";
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
 				spi-max-frequency = <24000000>;
 			};
 		};
 
-		pci@40000000 {
-			status = "ok";
-			perst-gpio = <&tlmm 38 0x1>;
-		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
+		pcie@40000000 {
+			status = "okay";
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts
index 8c7ef6537ae6..ea2987fcbff8 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts
@@ -1,20 +1,21 @@
 // SPDX-License-Identifier: GPL-2.0
 // Copyright (c) 2018, The Linux Foundation. All rights reserved.
 
+#include <dt-bindings/gpio/gpio.h>
 #include "qcom-ipq4019-ap.dk07.1.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C1";
-	compatible = "qcom,ipq4019-ap-dk07.1-c1";
+	compatible = "qcom,ipq4019-ap-dk07.1-c1", "qcom,ipq4019";
 
 	soc {
 		pci@40000000 {
-			status = "ok";
-			perst-gpio = <&tlmm 38 0x1>;
+			status = "okay";
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};
 
 		spi@78b6000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		pinctrl@1000000 {
@@ -43,20 +44,20 @@
 		serial@78b0000 {
 			pinctrl-0 = <&serial_1_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 
 		spi@78b5000 {
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
-			status = "ok";
-			cs-gpios = <&tlmm 12 0>;
+			status = "okay";
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0>;
-				compatible = "n25q128a11";
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
 				spi-max-frequency = <24000000>;
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts
index af7a9028d492..bd3553dd2070 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts
@@ -5,7 +5,7 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C2";
-	compatible = "qcom,ipq4019-ap-dk07.1-c2";
+	compatible = "qcom,ipq4019-ap-dk07.1-c2", "qcom,ipq4019";
 
 	soc {
 		pinctrl@1000000 {
@@ -19,7 +19,7 @@
 		serial@78b0000 {
 			pinctrl-0 = <&serial_1_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi
index 9f1a5a668772..7ef635997efa 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi
@@ -49,27 +49,27 @@
 		serial@78af000 {
 			pinctrl-0 = <&serial_0_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 
-		dma@7884000 {
-			status = "ok";
+		dma-controller@7884000 {
+			status = "okay";
 		};
 
 		i2c@78b7000 { /* BLSP1 QUP2 */
 			pinctrl-0 = <&i2c_0_pins>;
 			pinctrl-names = "default";
-			status = "ok";
+			status = "okay";
 		};
 
-		dma@7984000 {
-			status = "ok";
-		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
-			status = "ok";
+		dma-controller@7984000 {
+			status = "okay";
 		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
index 8ef26da32ff4..f989bd741cd1 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
@@ -102,10 +102,12 @@
 		L2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
+			qcom,saw = <&saw_l2>;
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -141,7 +143,7 @@
 	clocks {
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+			clock-frequency = <32000>;
 			#clock-cells = <0>;
 		};
 
@@ -154,7 +156,7 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-ipq4019";
+			compatible = "qcom,scm-ipq4019", "qcom,scm";
 		};
 	};
 
@@ -165,6 +167,7 @@
 			     <1 4 0xf08>,
 			     <1 1 0xf08>;
 		clock-frequency = <48000000>;
+		always-on;
 	};
 
 	soc {
@@ -184,11 +187,14 @@
 		gcc: clock-controller@1800000 {
 			compatible = "qcom,gcc-ipq4019";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x1800000 0x60000>;
+			clocks = <&xo>, <&sleep_clk>;
+			clock-names = "xo", "sleep_clk";
 		};
 
-		rng@22000 {
+		prng: rng@22000 {
 			compatible = "qcom,prng";
 			reg = <0x22000 0x140>;
 			clocks = <&gcc GCC_PRNG_AHB_CLK>;
@@ -200,25 +206,40 @@
 			compatible = "qcom,ipq4019-pinctrl";
 			reg = <0x01000000 0x300000>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 100>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		sdhci: sdhci@7824900 {
-			compatible = "qcom,sdhci-msm-v4";
+		vqmmc: regulator@1948000 {
+			compatible = "qcom,vqmmc-ipq4019-regulator";
+			reg = <0x01948000 0x4>;
+			regulator-name = "vqmmc";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+			status = "disabled";
+		};
+
+		sdhci: mmc@7824900 {
+			compatible = "qcom,ipq4019-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x7824900 0x11c>, <0x7824000 0x800>;
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 			bus-width = <8>;
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&gcc GCC_DCD_XO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
 			status = "disabled";
 		};
 
-		blsp_dma: dma@7884000 {
+		blsp_dma: dma-controller@7884000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x07884000 0x23000>;
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
@@ -238,8 +259,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 5>, <&blsp_dma 4>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -252,8 +273,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 7>, <&blsp_dma 6>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -261,13 +282,13 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x78b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 9>, <&blsp_dma 8>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -275,17 +296,17 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x78b8000 0x600>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 11>, <&blsp_dma 10>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-		cryptobam: dma@8e04000 {
+		cryptobam: dma-controller@8e04000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x08e04000 0x20000>;
 			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
@@ -297,7 +318,7 @@
 			status = "disabled";
 		};
 
-		crypto@8e3a000 {
+		crypto: crypto@8e3a000 {
 			compatible = "qcom,crypto-v5.1";
 			reg = <0x08e3a000 0x6000>;
 			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
@@ -309,22 +330,22 @@
 			status = "disabled";
 		};
 
-		acc0: clock-controller@b088000 {
+		acc0: power-manager@b088000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b088000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		acc1: clock-controller@b098000 {
+		acc1: power-manager@b098000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b098000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		acc2: clock-controller@b0a8000 {
+		acc2: power-manager@b0a8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b0a8000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		acc3: clock-controller@b0b8000 {
+		acc3: power-manager@b0b8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b0b8000 0x1000>, <0xb008000 0x1000>;
 		};
@@ -332,7 +353,7 @@
 		saw0: regulator@b089000 {
 			compatible = "qcom,saw2";
 			reg = <0x0b089000 0x1000>, <0x0b009000 0x1000>;
-                        regulator;
+			regulator;
 		};
 
 		saw1: regulator@b099000 {
@@ -353,6 +374,12 @@
 			regulator;
 		};
 
+		saw_l2: regulator@b012000 {
+			compatible = "qcom,saw2";
+			reg = <0xb012000 0x1000>;
+			regulator;
+		};
+
 		blsp1_uart1: serial@78af000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x78af000 0x200>;
@@ -361,8 +388,8 @@
 			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 1>, <&blsp_dma 0>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+			dma-names = "tx", "rx";
 		};
 
 		blsp1_uart2: serial@78b0000 {
@@ -373,12 +400,12 @@
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 3>, <&blsp_dma 2>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
 		};
 
-		watchdog@b017000 {
-			compatible = "qcom,kpss-wdt", "qcom,kpss-wdt-ipq4019";
+		watchdog: watchdog@b017000 {
+			compatible = "qcom,kpss-wdt-ipq4019", "qcom,kpss-wdt";
 			reg = <0xb017000 0x40>;
 			clocks = <&sleep_clk>;
 			timeout-sec = <10>;
@@ -390,12 +417,12 @@
 			reg = <0x4ab000 0x4>;
 		};
 
-		pcie0: pci@40000000 {
-			compatible = "qcom,pcie-ipq4019", "snps,dw-pcie";
-			reg =  <0x40000000 0xf1d
-				0x40000f20 0xa8
-				0x80000 0x2000
-				0x40100000 0x1000>;
+		pcie0: pcie@40000000 {
+			compatible = "qcom,pcie-ipq4019";
+			reg = <0x40000000 0xf1d>,
+			      <0x40000f20 0xa8>,
+			      <0x80000 0x2000>,
+			      <0x40100000 0x1000>;
 			reg-names = "dbi", "elbi", "parf", "config";
 			device_type = "pci";
 			linux,pci-domain = <0>;
@@ -404,8 +431,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000>,
-				 <0x82000000 0 0x40300000 0x40300000 0 0x00d00000>;
+			ranges = <0x81000000 0x0 0x00000000 0x40200000 0x0 0x00100000>,
+				 <0x82000000 0x0 0x40300000 0x40300000 0x0 0x00d00000>;
 
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
@@ -450,7 +477,7 @@
 			status = "disabled";
 		};
 
-		qpic_bam: dma@7984000 {
+		qpic_bam: dma-controller@7984000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x7984000 0x1a000>;
 			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
@@ -461,7 +488,7 @@
 			status = "disabled";
 		};
 
-		nand: qpic-nand@79b0000 {
+		nand: nand-controller@79b0000 {
 			compatible = "qcom,ipq4019-nand";
 			reg = <0x79b0000 0x1000>;
 			#address-cells = <1>;
@@ -519,9 +546,9 @@
 				     <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names =  "msi0",  "msi1",  "msi2",  "msi3",
-					   "msi4",  "msi5",  "msi6",  "msi7",
-					   "msi8",  "msi9", "msi10", "msi11",
+			interrupt-names = "msi0",  "msi1",  "msi2",  "msi3",
+					  "msi4",  "msi5",  "msi6",  "msi7",
+					  "msi8",  "msi9", "msi10", "msi11",
 					  "msi12", "msi13", "msi14", "msi15",
 					  "legacy";
 			status = "disabled";
@@ -561,12 +588,114 @@
 				     <GIC_SPI 62 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 63 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names =  "msi0",  "msi1",  "msi2",  "msi3",
-					   "msi4",  "msi5",  "msi6",  "msi7",
-					   "msi8",  "msi9", "msi10", "msi11",
+			interrupt-names = "msi0",  "msi1",  "msi2",  "msi3",
+					  "msi4",  "msi5",  "msi6",  "msi7",
+					  "msi8",  "msi9", "msi10", "msi11",
 					  "msi12", "msi13", "msi14", "msi15",
 					  "legacy";
 			status = "disabled";
 		};
+
+		mdio: mdio@90000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "qcom,ipq4019-mdio";
+			reg = <0x90000 0x64>;
+			status = "disabled";
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+
+			ethphy4: ethernet-phy@4 {
+				reg = <4>;
+			};
+		};
+
+		usb3_ss_phy: usb-phy@9a000 {
+			compatible = "qcom,usb-ss-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0x9a000 0x800>;
+			reg-names = "phy_base";
+			resets = <&gcc USB3_UNIPHY_PHY_ARES>;
+			reset-names = "por_rst";
+			status = "disabled";
+		};
+
+		usb3_hs_phy: usb-phy@a6000 {
+			compatible = "qcom,usb-hs-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0xa6000 0x40>;
+			reg-names = "phy_base";
+			resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
+			reset-names = "por_rst", "srif_rst";
+			status = "disabled";
+		};
+
+		usb3: usb@8af8800 {
+			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
+			reg = <0x8af8800 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc GCC_USB3_MASTER_CLK>,
+				 <&gcc GCC_USB3_SLEEP_CLK>,
+				 <&gcc GCC_USB3_MOCK_UTMI_CLK>;
+			clock-names = "core", "sleep", "mock_utmi";
+			ranges;
+			status = "disabled";
+
+			usb3_dwc: usb@8a00000 {
+				compatible = "snps,dwc3";
+				reg = <0x8a00000 0xf8000>;
+				interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+			};
+		};
+
+		usb2_hs_phy: usb-phy@a8000 {
+			compatible = "qcom,usb-hs-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0xa8000 0x40>;
+			reg-names = "phy_base";
+			resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
+			reset-names = "por_rst", "srif_rst";
+			status = "disabled";
+		};
+
+		usb2: usb@60f8800 {
+			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
+			reg = <0x60f8800 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc GCC_USB2_MASTER_CLK>,
+				 <&gcc GCC_USB2_SLEEP_CLK>,
+				 <&gcc GCC_USB2_MOCK_UTMI_CLK>;
+			clock-names = "master", "sleep", "mock_utmi";
+			ranges;
+			status = "disabled";
+
+			usb@6000000 {
+				compatible = "snps,dwc3";
+				reg = <0x6000000 0xf8000>;
+				interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_hs_phy>;
+				phy-names = "usb2-phy";
+				dr_mode = "host";
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi
new file mode 100644
index 000000000000..9d06255104c7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8062.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi
new file mode 100644
index 000000000000..5d3ebd3e2e51
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8062";
+	compatible = "qcom,ipq8062", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts
index 554c65e7aa0e..a654d3c22c4f 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts
@@ -3,16 +3,10 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ8064/AP-148";
-	compatible = "qcom,ipq8064-ap148";
+	compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
 
 	soc {
 		pinmux@800000 {
-			i2c4_pins: i2c4_pinmux {
-				pins = "gpio12", "gpio13";
-				function = "gsbi4";
-				bias-disable;
-			};
-
 			buttons_pins: buttons_pins {
 				mux {
 					pins = "gpio54", "gpio65";
@@ -24,7 +18,7 @@
 
 		gsbi@16300000 {
 			i2c@16380000 {
-				status = "ok";
+				status = "okay";
 				clock-frequency = <200000>;
 				pinctrl-0 = <&i2c4_pins>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts
new file mode 100644
index 000000000000..12e806adcda8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts
@@ -0,0 +1,472 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "MikroTik RB3011UiAS-RM";
+	compatible = "mikrotik,rb3011", "qcom,ipq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac3;
+		mdio-gpio0 = &mdio0;
+		mdio-gpio1 = &mdio1;
+	};
+
+	chosen {
+		bootargs = "loglevel=8 console=ttyMSM0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&buttons_pins>;
+		pinctrl-names = "default";
+
+		button {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led-0 {
+			label = "rb3011:green:user";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	memory@42000000 {
+		reg = <0x42000000 0x3e000000>;
+		device_type = "memory";
+	};
+
+	mdio0: mdio-0 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio0_pins>;
+		pinctrl-names = "default";
+
+		switch0: switch@10 {
+			compatible = "qca,qca8337";
+
+			dsa,member = <0 0>;
+
+			pinctrl-0 = <&sw0_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch0cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii-id";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw1";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw2";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw3";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw4";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw5";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+			};
+		};
+	};
+
+	mdio1: mdio-1 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio1_pins>;
+		pinctrl-names = "default";
+
+		switch1: switch@14 {
+			compatible = "qca,qca8337";
+
+			dsa,member = <1 0>;
+
+			pinctrl-0 = <&sw1_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch1cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac3>;
+					phy-mode = "sgmii";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw6";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw7";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw8";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw9";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw10";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+			};
+		};
+	};
+
+	soc {
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				norflash: flash@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "RouterBoot";
+						reg = <0x0 0x40000>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&gmac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <0>;
+	phy-handle = <&switch0cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac3 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <3>;
+	phy-handle = <&switch1cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi7 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&hs_phy_1 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				label = "RouterBoard NAND 1 Boot";
+				reg = <0x0000000 0x0800000>;
+			};
+
+			main@800000 {
+				label = "RouterBoard NAND 1 Main";
+				reg = <0x0800000 0x7800000>;
+			};
+		};
+	};
+};
+
+&qcom_pinmux {
+	buttons_pins: buttons_pins {
+		mux {
+			pins = "gpio66";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	leds_pins: leds_pins {
+		mux {
+			pins = "gpio33";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio1_pins {
+		mux {
+			pins = "gpio10", "gpio11";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	sw0_reset_pin: sw0_reset_pin {
+		mux {
+			pins = "gpio16";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	sw1_reset_pin: sw1_reset_pin {
+		mux {
+			pins = "gpio17";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&ss_phy_1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi
new file mode 100644
index 000000000000..ac9c44f0c164
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi
new file mode 100644
index 000000000000..49de9752632f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&buttons_pins>;
+		pinctrl-names = "default";
+
+		button-1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+		button-2 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led-0 {
+			label = "led_usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbdev";
+			default-state = "off";
+		};
+
+		led-1 {
+			label = "led_usb3";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbdev";
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "status_led_fail";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "sata_led";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-4 {
+			label = "status_led_pass";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	soc {
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "okay";
+
+			serial@16340000 {
+				status = "okay";
+			};
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 0>;
+
+				flash: flash@0 {
+					compatible = "s25fl256s1";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "rootfs";
+						reg = <0x0 0x1000000>;
+					};
+
+					partition@1 {
+						label = "scratch";
+						reg = <0x1000000 0x1000000>;
+					};
+				};
+			};
+		};
+
+		sata-phy@1b400000 {
+			status = "okay";
+		};
+
+		sata@29000000 {
+			ports-implemented = <0x1>;
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi
new file mode 100644
index 000000000000..0442580b22de
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi
new file mode 100644
index 000000000000..2f117d576daf
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v2.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	serial@16340000 {
+		status = "okay";
+	};
+	/*
+	 * The i2c device on gsbi4 should not be enabled.
+	 * On ipq806x designs gsbi4 i2c is meant for exclusive
+	 * RPM usage. Turning this on in kernel manifests as
+	 * i2c failure for the RPM.
+	 */
+};
+
+&pcie0 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie1 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie2 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&sata {
+	ports-implemented = <0x1>;
+};
+
+&ss_phy_0 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&ss_phy_1 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
new file mode 100644
index 000000000000..6a7f4dd0f775
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
@@ -0,0 +1,1377 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm IPQ8064";
+	compatible = "qcom,ipq8064";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	thermal-zones {
+		sensor0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor2-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor4-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor5-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor6-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor7-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor8-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor9-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor10-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	cpu-pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+					  IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		nss@40000000 {
+			reg = <0x40000000 0x1000000>;
+			no-map;
+		};
+
+		smem: smem@41000000 {
+			compatible = "qcom,smem";
+			reg = <0x41000000 0x200000>;
+			no-map;
+
+			hwlocks = <&sfpb_mutex 3>;
+		};
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+
+		pxo_board: pxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			#clock-cells = <0>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-ipq806x", "qcom,scm";
+		};
+	};
+
+	stmmac_axi_setup: stmmac-axi-config {
+		snps,wr_osr_lmt = <7>;
+		snps,rd_osr_lmt = <7>;
+		snps,blen = <16 0 0 0 0 0 0>;
+	};
+
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x00108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+		};
+
+		ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		qfprom: qfprom@700000 {
+			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			speedbin_efuse: speedbin@c0 {
+				reg = <0xc0 0x4>;
+			};
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_calib_backup: calib_backup@410 {
+				reg = <0x410 0xb>;
+			};
+		};
+
+		qcom_pinmux: pinmux@800000 {
+			compatible = "qcom,ipq8064-pinctrl";
+			reg = <0x00800000 0x4000>;
+
+			gpio-controller;
+			gpio-ranges = <&qcom_pinmux 0 0 69>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+
+			pcie0_pins: pcie0_pinmux {
+				mux {
+					pins = "gpio3";
+					function = "pcie1_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			pcie1_pins: pcie1_pinmux {
+				mux {
+					pins = "gpio48";
+					function = "pcie2_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			pcie2_pins: pcie2_pinmux {
+				mux {
+					pins = "gpio63";
+					function = "pcie3_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			i2c4_pins: i2c4-default {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				drive-strength = <12>;
+				bias-disable;
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+			};
+
+			leds_pins: leds_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9",
+					       "gpio26", "gpio53";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+					output-low;
+				};
+			};
+
+			buttons_pins: buttons_pins {
+				mux {
+					pins = "gpio54";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				pullups {
+					pins = "gpio39";
+					function = "nand";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0-pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "mdio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2-pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29",
+					       "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59",
+					       "gpio60", "gpio61", "gpio62";
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-ipq8064", "syscon";
+			clocks = <&pxo_board>, <&cxo_board>, <&lcc PLL4>;
+			clock-names = "pxo", "cxo", "pll4";
+			reg = <0x00900000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			tsens: thermal-sensor {
+				compatible = "qcom,ipq8064-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		sfpb_mutex: hwlock@1200600 {
+			compatible = "qcom,sfpb-mutex";
+			reg = <0x01200600 0x100>;
+
+			#hwlock-cells = <1>;
+		};
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-ipq8064", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <25000000>;
+			clocks = <&sleep_clk>;
+			clock-names = "sleep";
+			cpu-offset = <0x80000>;
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
+		};
+
+		acc0: clock-controller@2088000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
+		};
+
+		saw0: regulator@2089000 {
+			compatible = "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		acc1: clock-controller@2098000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
+		};
+
+		saw1: regulator@2099000 {
+			compatible = "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		nss_common: syscon@3000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
+
+		usb3_0: usb@100f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_0: usb@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_0: phy@100f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_0: phy@100f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb3_1: usb@110f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_1: usb@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: phy@110f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_1: phy@110f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		amba: amba {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12180000 0x2000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <192000000>;
+				sd-uhs-sdr104;
+				sd-uhs-ddr50;
+				vqmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+				dma-names = "tx", "rx";
+			};
+
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12400000 0x2000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				vmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		gsbi1: gsbi@12440000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x12440000 0x100>;
+			cell-index = <1>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_serial: serial@12450000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12450000 0x100>,
+				      <0x12400000 0x03>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+
+				status = "disabled";
+			};
+
+			gsbi1_i2c: i2c@12460000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x12460000 0x1000>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gsbi2: gsbi@12480000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <2>;
+			reg = <0x12480000 0x100>;
+			clocks = <&gcc GSBI2_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi2_serial: serial@12490000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12490000 0x1000>,
+				      <0x12480000 0x1000>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi2_i2c: i2c@124a0000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x124a0000 0x1000>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gsbi4: gsbi@16300000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <4>;
+			reg = <0x16300000 0x100>;
+			clocks = <&gcc GSBI4_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x1000>,
+				      <0x16300000 0x1000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			i2c@16380000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16380000 0x1000>;
+				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gsbi6: gsbi@16500000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x16500000 0x100>;
+			cell-index = <6>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			gsbi6_spi: spi@16580000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gsbi7: gsbi@16600000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <7>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi7_i2c: i2c@16680000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		adm_dma: dma-controller@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
+
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
+
+			status = "disabled";
+		};
+
+		gsbi5: gsbi@1a200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x1a200000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi5_serial: serial@1a240000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x1a240000 0x1000>,
+				      <0x1a200000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			i2c@1a280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			spi@1a280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-ipq8064", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+		};
+
+		nand: nand-controller@1ac00000 {
+			compatible = "qcom,ipq806x-nand";
+			reg = <0x1ac00000 0x800>;
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			clocks = <&gcc EBI2_CLK>,
+				 <&gcc EBI2_AON_CLK>;
+			clock-names = "core", "aon";
+
+			dmas = <&adm_dma 3>;
+			dma-names = "rxtx";
+			qcom,cmd-crci = <15>;
+			qcom,data-crci = <3>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sata_phy: sata-phy@1b400000 {
+			compatible = "qcom,ipq806x-sata-phy";
+			reg = <0x1b400000 0x200>;
+
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		pcie0: pcie@1b500000 {
+			compatible = "qcom,pcie-ipq8064";
+			reg = <0x1b500000 0x1000
+			       0x1b502000 0x80
+			       0x1b600000 0x100
+			       0x0ff00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* MEM */
+
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc PCIE_A_CLK>,
+				 <&gcc PCIE_H_CLK>,
+				 <&gcc PCIE_PHY_CLK>,
+				 <&gcc PCIE_AUX_CLK>,
+				 <&gcc PCIE_ALT_REF_CLK>;
+			clock-names = "core", "iface", "phy", "aux", "ref";
+
+			assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc PCIE_ACLK_RESET>,
+				 <&gcc PCIE_HCLK_RESET>,
+				 <&gcc PCIE_POR_RESET>,
+				 <&gcc PCIE_PCI_RESET>,
+				 <&gcc PCIE_PHY_RESET>,
+				 <&gcc PCIE_EXT_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+			perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+		};
+
+		pcie1: pcie@1b700000 {
+			compatible = "qcom,pcie-ipq8064";
+			reg = <0x1b700000 0x1000
+			       0x1b702000 0x80
+			       0x1b800000 0x100
+			       0x31f00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x31e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x2e000000 0x2e000000 0x0 0x03e00000>; /* MEM */
+
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc PCIE_1_A_CLK>,
+				 <&gcc PCIE_1_H_CLK>,
+				 <&gcc PCIE_1_PHY_CLK>,
+				 <&gcc PCIE_1_AUX_CLK>,
+				 <&gcc PCIE_1_ALT_REF_CLK>;
+			clock-names = "core", "iface", "phy", "aux", "ref";
+
+			assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc PCIE_1_ACLK_RESET>,
+				 <&gcc PCIE_1_HCLK_RESET>,
+				 <&gcc PCIE_1_POR_RESET>,
+				 <&gcc PCIE_1_PCI_RESET>,
+				 <&gcc PCIE_1_PHY_RESET>,
+				 <&gcc PCIE_1_EXT_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+			perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+		};
+
+		pcie2: pcie@1b900000 {
+			compatible = "qcom,pcie-ipq8064";
+			reg = <0x1b900000 0x1000
+			       0x1b902000 0x80
+			       0x1ba00000 0x100
+			       0x35f00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <2>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x35e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x32000000 0x32000000 0x0 0x03e00000>; /* MEM */
+
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc PCIE_2_A_CLK>,
+				 <&gcc PCIE_2_H_CLK>,
+				 <&gcc PCIE_2_PHY_CLK>,
+				 <&gcc PCIE_2_AUX_CLK>,
+				 <&gcc PCIE_2_ALT_REF_CLK>;
+			clock-names = "core", "iface", "phy", "aux", "ref";
+
+			assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc PCIE_2_ACLK_RESET>,
+				 <&gcc PCIE_2_HCLK_RESET>,
+				 <&gcc PCIE_2_POR_RESET>,
+				 <&gcc PCIE_2_PCI_RESET>,
+				 <&gcc PCIE_2_PHY_RESET>,
+				 <&gcc PCIE_2_EXT_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+			pinctrl-0 = <&pcie2_pins>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+			perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
+		};
+
+		qsgmii_csr: syscon@1bb00000 {
+			compatible = "syscon";
+			reg = <0x1bb00000 0x000001FF>;
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-ipq8064";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		lpass@28100000 {
+			compatible = "qcom,lpass-cpu";
+			status = "disabled";
+			clocks = <&lcc AHBIX_CLK>,
+					<&lcc MI2S_OSR_CLK>,
+					<&lcc MI2S_BIT_CLK>;
+			clock-names = "ahbix-clk",
+					"mi2s-osr-clk",
+					"mi2s-bit-clk";
+			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "lpass-irq-lpaif";
+			reg = <0x28100000 0x10000>;
+			reg-names = "lpass-lpaif";
+		};
+
+		sata: sata@29000000 {
+			compatible = "qcom,ipq806x-ahci", "generic-ahci";
+			reg = <0x29000000 0x180>;
+
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_face", "iface", "core",
+					"rxoob", "pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		gmac0: ethernet@37000000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37000000 0x200000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE1_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE1_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+
+		gmac1: ethernet@37200000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37200000 0x200000>;
+			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE2_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE2_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+
+		gmac2: ethernet@37400000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37400000 0x200000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE3_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE3_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+
+		gmac3: ethernet@37600000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37600000 0x200000>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE4_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE4_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi
new file mode 100644
index 000000000000..803e6ff99ef8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8065.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi
new file mode 100644
index 000000000000..ea49f6cc416d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8065";
+	compatible = "qcom,ipq8065", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
index 26160c324802..e3b4b93c3d38 100644
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
@@ -1,53 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
  * Device Tree Source for mangOH Green Board with WP8548 Module
  *
  * Copyright (C) 2016 BayLibre, SAS.
  * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 #include "qcom-mdm9615-wp8548.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "MangOH Green with WP8548 Module";
@@ -82,17 +45,16 @@
 	 * - 42: IOT0_GPIO1 and SD Card Detect
 	 */
 
-	gpioext1_pins: gpioext1_pins {
-		pins {
+	gpioext1_pins: gpioext1-state {
+		gpioext1-pins {
 			pins = "gpio2";
 			function = "gpio";
-			input-enable;
 			bias-disable;
 		};
 	};
 
-	sdc_cd_pins: sdc_cd_pins {
-		pins {
+	sdc_cd_pins: sdc-cd-state {
+		sdc-cd-pins {
 			pins = "gpio42";
 			function = "gpio";
 			drive-strength = <2>;
@@ -103,7 +65,7 @@
 
 &gsbi3_spi {
 	spi@0 {
-		compatible = "swir,mangoh-iotport-spi", "spidev";
+		compatible = "swir,mangoh-iotport-spi";
 		spi-max-frequency = <24000000>;
 		reg = <0>;
 	};
@@ -143,7 +105,7 @@
 				compatible = "smsc,usb3503a";
 				reg = <0x8>;
 				connect-gpios = <&gpioext2 1 GPIO_ACTIVE_HIGH>;
-				intn-gpios = <&gpioext2 0 GPIO_ACTIVE_LOW>;
+				intn-gpios = <&gpioext2 0 GPIO_ACTIVE_HIGH>;
 				initial-mode = <1>;
 			};
 		};
@@ -153,7 +115,7 @@
 			#size-cells = <0>;
 			reg = <4>;
 
-			gpioext0: gpio@3e {
+			gpioext0: pinctrl@3e {
 				/* GPIO Expander 0 Mapping :
 				 * - 0: ARDUINO_RESET_Level shift
 				 * - 1: BattChrgr_PG_N
@@ -179,7 +141,7 @@
 				interrupt-parent = <&gpioext1>;
 				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
@@ -191,7 +153,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			gpioext1: gpio@3f {
+			gpioext1: pinctrl@3f {
 				/* GPIO Expander 1 Mapping :
 				 * - 0: GPIOEXP_INT1
 				 * - 1: Battery detect
@@ -220,7 +182,7 @@
 				interrupt-parent = <&msmgpio>;
 				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
@@ -232,7 +194,7 @@
 			#size-cells = <0>;
 			reg = <6>;
 
-			gpioext2: gpio@70 {
+			gpioext2: pinctrl@70 {
 				/* GPIO Expander 2 Mapping :
 				 * - 0: USB_HUB_INTn
 				 * - 1: HUB_CONNECT
@@ -258,7 +220,7 @@
 				interrupt-parent = <&gpioext1>;
 				interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
new file mode 100644
index 000000000000..0dd52cac0e2e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Sierra Wireless WP8548 Module
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "qcom-mdm9615.dtsi"
+#include "pm8018.dtsi"
+
+/ {
+	model = "Sierra Wireless WP8548 Module";
+	compatible = "swir,wp8548", "qcom,mdm9615";
+
+	memory@48000000 {
+		device_type = "memory";
+		reg = <0x48000000 0x7F00000>;
+	};
+};
+
+&msmgpio {
+	pinctrl-0 = <&reset_out_pins>;
+	pinctrl-names = "default";
+
+	gsbi3_pins: gsbi3-state {
+		gsbi3-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "gsbi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	gsbi4_pins: gsbi4-state {
+		gsbi4-pins {
+			pins = "gpio12", "gpio13", "gpio14", "gpio15";
+			function = "gsbi4";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	gsbi5_i2c_pins: gsbi5-i2c-state {
+		sda-pins {
+			pins = "gpio16";
+			function = "gsbi5_i2c";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		scl-pins {
+			pins = "gpio17";
+			function = "gsbi5_i2c";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	gsbi5_uart_pins: gsbi5-uart-state {
+		gsbi5-uart-pins {
+			pins = "gpio18", "gpio19";
+			function = "gsbi5_uart";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	reset_out_pins: reset-out-state {
+		reset-out-pins {
+			pins = "gpio66";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+};
+
+&pm8018 {
+	interrupts-extended = <&intc GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&pm8018_gpio {
+	usb_vbus_5v_pins: usb-vbus-5v-state {
+		pins = "gpio4";
+		function = "normal";
+		output-high;
+		bias-disable;
+		qcom,drive-strength = <1>;
+		power-source = <2>;
+	};
+};
+
+&gsbi3 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_SPI>;
+};
+
+&gsbi3_spi {
+	status = "okay";
+	pinctrl-0 = <&gsbi3_pins>;
+	pinctrl-names = "default";
+	assigned-clocks = <&gcc GSBI3_QUP_CLK>;
+	assigned-clock-rates = <24000000>;
+};
+
+&gsbi4 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+};
+
+&gsbi4_serial {
+	status = "okay";
+	pinctrl-0 = <&gsbi4_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi5_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+	pinctrl-0 = <&gsbi5_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5_serial {
+	status = "okay";
+	pinctrl-0 = <&gsbi5_uart_pins>;
+	pinctrl-names = "default";
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8018-regulators";
+
+		vin_lvs1-supply = <&pm8018_s3>;
+
+		vdd_l7-supply = <&pm8018_s4>;
+		vdd_l8-supply = <&pm8018_s3>;
+		vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
+
+		/* Buck SMPS */
+		pm8018_s1: s1 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s2: s2 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s3: s3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s4: s4 {
+			regulator-min-microvolt = <2100000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s5: s5 {
+			regulator-always-on;
+			regulator-min-microvolt = <1350000>;
+			regulator-max-microvolt = <1350000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8018_l2: l2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8018_l3: l3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8018_l4: l4 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8018_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8018_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8018_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8018_l8: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8018_l9: l9 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8018_l10: l10 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l11: l11 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l12: l12 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l13: l13 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8018_l14: l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8018_lvs1: lvs1 {
+			bias-pull-down;
+		};
+	};
+};
+
+&sdcc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
new file mode 100644
index 000000000000..34c60994d026
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Qualcomm MDM9615 SoC
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-mdm9615.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-mdm9615.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm MDM9615";
+	compatible = "qcom,mdm9615";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a5";
+			reg = <0>;
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+		};
+	};
+
+	cpu-pmu {
+		compatible = "arm,cortex-a5-pmu";
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+	};
+
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		L2: cache-controller@2040000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x02040000 0x1000>;
+			arm,data-latency = <2 2 0>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-mdm9615", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <27000000>;
+			cpu-offset = <0x80000>;
+		};
+
+		msmgpio: pinctrl@800000 {
+			compatible = "qcom,mdm9615-pinctrl";
+			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 88>;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x800000 0x4000>;
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-mdm9615";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x900000 0x4000>;
+			clocks = <&cxo_board>,
+				 <&lcc PLL4>;
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-mdm9615";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&cxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "cxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-mdm9615", "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+			assigned-clocks = <&gcc PRNG_CLK>;
+			assigned-clock-rates = <32000000>;
+		};
+
+		gsbi2: gsbi@16100000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <2>;
+			reg = <0x16100000 0x100>;
+			clocks = <&gcc GSBI2_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi2_i2c: i2c@16180000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16180000 0x1000>;
+				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <3>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi3_spi: spi@16280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi4: gsbi@16300000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <4>;
+			reg = <0x16300000 0x100>;
+			clocks = <&gcc GSBI4_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x1000>,
+				      <0x16300000 0x1000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi5: gsbi@16400000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x16400000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi5_i2c: i2c@16480000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16480000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				/* QUP clock is not initialized, set rate */
+				assigned-clocks = <&gcc GSBI5_QUP_CLK>;
+				assigned-clock-rates = <24000000>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi5_serial: serial@16440000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16440000 0x1000>,
+				      <0x16400000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		ssbi: ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		sdcc1bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc2bam: dma-controller@12142000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12142000 0x8000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1: mmc@12180000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <48000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC1_CLK>;
+			assigned-clock-rates = <400000>;
+		};
+
+		sdcc2: mmc@12140000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12140000 0x2000>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC2_CLK>;
+			assigned-clock-rates = <400000>;
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-mdm9615", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-mdm9615";
+			reg = <0x108000 0x1000>;
+
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi
new file mode 100644
index 000000000000..525d8c608b06
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Common Board Device Tree for Microsoft MSM8x26-based Lumias
+ *
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+#include <dt-bindings/input/input.h>
+
+/*
+ * Delete all generic (msm8226.dtsi) reserved
+ * memory mappings which are different on these devices.
+ */
+/delete-node/ &smem_region;
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1; /* eMMC */
+		mmc1 = &sdhc_2; /* microSD */
+		display0 = &framebuffer;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x3200000 0x800000>;
+			format = "a8r8g8b8";
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 4)>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			power-domains = <&mmcc MDSS_GDSC>;
+		};
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_default>;
+		pinctrl-names = "default";
+
+		label = "GPIO Buttons";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	/*
+	 * This device being a WP platform has a different
+	 * memory layout than other Android based devices.
+	 * This smem memory region is directly copied from
+	 * the original UEFI firmware.
+	 */
+	reserved-memory {
+		display_reserved: framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen: touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&pm8226_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		/* These values were taken from the original firmware DSDT */
+		pm8226_s1: s1 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2100000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2075000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	status = "okay";
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
+
+&tlmm {
+	gpio_keys_default: gpio-keys-default-state {
+		pins = "gpio106", "gpio107", "gpio108";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	touchscreen_default: touchscreen-default-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-dempsey.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-dempsey.dts
new file mode 100644
index 000000000000..2c664b5934ec
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-dempsey.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/ {
+	model = "Microsoft Lumia 640";
+	compatible = "microsoft,dempsey", "qcom,msm8226";
+	chassis-type = "handset";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-makepeace.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-makepeace.dts
new file mode 100644
index 000000000000..731c5c375678
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-makepeace.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/ {
+	model = "Microsoft Lumia 640 XL";
+	compatible = "microsoft,makepeace", "qcom,msm8226";
+	chassis-type = "handset";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-moneypenny.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-moneypenny.dts
new file mode 100644
index 000000000000..992b7115b5f8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-moneypenny.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/ {
+	model = "Nokia Lumia 630";
+	compatible = "microsoft,moneypenny", "qcom,msm8226";
+	chassis-type = "handset";
+};
+
+&framebuffer {
+	width = <480>;
+	height = <854>;
+	stride = <(480 * 4)>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts
new file mode 100644
index 000000000000..288cacd5d1fa
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "qcom-msm8226.dtsi"
+
+/ {
+	model = "Samsung Galaxy S III Neo";
+	compatible = "samsung,s3ve3g", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi
new file mode 100644
index 000000000000..b492c95e5d30
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi
@@ -0,0 +1,1106 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	chosen { };
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8226", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	rpm: remoteproc {
+		compatible = "qcom,msm8226-rpm-proc", "qcom,rpm-proc";
+
+		master-stats {
+			compatible = "qcom,rpm-master-stats";
+			qcom,rpm-msg-ram = <&apss_master_stats>,
+					   <&mpss_master_stats>,
+					   <&lpss_master_stats>,
+					   <&pronto_master_stats>;
+			qcom,master-names = "APSS",
+					    "MPSS",
+					    "LPSS",
+					    "PRONTO";
+		};
+
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8226";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8226", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8226-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <1>;
+						};
+						rpmpd_opp_svs_krait: opp2 {
+							opp-level = <2>;
+						};
+						rpmpd_opp_svs_soc: opp3 {
+							opp-level = <3>;
+						};
+						rpmpd_opp_nom: opp4 {
+							opp-level = <4>;
+						};
+						rpmpd_opp_turbo: opp5 {
+							opp-level = <5>;
+						};
+						rpmpd_opp_super_turbo: opp6 {
+							opp-level = <6>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		smem_region: smem@3000000 {
+			reg = <0x3000000 0x100000>;
+			no-map;
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+
+		memory-region = <&smem_region>;
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		intc: interrupt-controller@f9000000 {
+			compatible = "qcom,msm-qgic2";
+			reg = <0xf9000000 0x1000>,
+			      <0xf9002000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		apcs: syscon@f9011000 {
+			compatible = "syscon";
+			reg = <0xf9011000 0x1000>;
+		};
+
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc1_default_state>;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc2_default_state>;
+			status = "disabled";
+		};
+
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc3_default_state>;
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@f991d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991d000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@f991e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991e000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core",
+				      "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart3: serial@f991f000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991f000 0x1000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart4: serial@f9920000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf9920000 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@f9923000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c1_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c2_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c3_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c4: i2c@f9926000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9926000 0x1000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c4_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c5: i2c@f9927000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9927000 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c5_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@f9928000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9928000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core",
+				      "iface";
+			pinctrl-0 = <&blsp1_i2c6_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8226-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfda0c000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <400000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8226",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+						 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					qcom,init-seq = /bits/ 8 <0x0 0x44
+						0x1 0x68 0x2 0x24 0x3 0x13>;
+				};
+			};
+		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8226";
+			reg = <0xfc400000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&sleep_clk>;
+			clock-names = "xo",
+				      "sleep_clk";
+		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8226";
+			reg = <0xfd8c0000 0x6000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&gcc GCC_MMSS_GPLL0_CLK_SRC>,
+				 <&gcc GPLL0_VOTE>,
+				 <&gcc GPLL1_VOTE>,
+				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>;
+			clock-names = "xo",
+				      "mmss_gpll0_vote",
+				      "gpll0_vote",
+				      "gpll1_vote",
+				      "gfx3d_clk_src",
+				      "dsi0pll",
+				      "dsi0pllbyte";
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,msm8226-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 117>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			blsp1_i2c1_pins: blsp1-i2c1-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c2_pins: blsp1-i2c2-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c3_pins: blsp1-i2c3-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c4_pins: blsp1-i2c4-state {
+				pins = "gpio14", "gpio15";
+				function = "blsp_i2c4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c5_pins: blsp1-i2c5-state {
+				pins = "gpio18", "gpio19";
+				function = "blsp_i2c5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c6_pins: blsp1-i2c6-state {
+				pins = "gpio22", "gpio23";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_default: cci-default-state {
+				pins = "gpio29", "gpio30";
+				function = "cci_i2c0";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_sleep: cci-sleep-state {
+				pins = "gpio29", "gpio30";
+				function = "gpio";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdhc1_default_state: sdhc1-default-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data-pins {
+					pins = "sdc1_cmd", "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc2_default_state: sdhc2-default-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data-pins {
+					pins = "sdc2_cmd", "sdc2_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc3_default_state: sdhc3-default-state {
+				clk-pins {
+					pins = "gpio44";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "gpio43";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "gpio39", "gpio40", "gpio41", "gpio42";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
+		};
+
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8226-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2";
+			#qcom,sensors = <6>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,msm8226-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@1c1 {
+				reg = <0x1c1 0x2>;
+				bits = <5 8>;
+			};
+
+			tsens_s0_p1: s0-p1@1c2 {
+				reg = <0x1c2 0x2>;
+				bits = <5 6>;
+			};
+
+			tsens_s1_p1: s1-p1@1c4 {
+				reg = <0x1c4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p1: s2-p1@1c4 {
+				reg = <0x1c4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p1: s3-p1@1c5 {
+				reg = <0x1c5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p1: s4-p1@1c6 {
+				reg = <0x1c6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p1: s5-p1@1c7 {
+				reg = <0x1c7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s6_p1: s6-p1@1ca {
+				reg = <0x1ca 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2: base2@1cc {
+				reg = <0x1cc 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p2: s0-p2@1cd {
+				reg = <0x1cd 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p2: s1-p2@1cd {
+				reg = <0x1cd 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p2: s2-p2@1ce {
+				reg = <0x1ce 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p2: s3-p2@1cf {
+				reg = <0x1cf 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p2: s4-p2@446 {
+				reg = <0x446 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@447 {
+				reg = <0x447 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@44e {
+				reg = <0x44e 0x1>;
+				bits = <1 6>;
+			};
+
+			tsens_mode: mode@44f {
+				reg = <0x44f 0x1>;
+				bits = <5 3>;
+			};
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		rng@f9bff000 {
+			compatible = "qcom,prng";
+			reg = <0xf9bff000 0x200>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		timer@f9020000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xf9020000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			frame@f9021000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9021000 0x1000>,
+				      <0xf9022000 0x1000>;
+			};
+
+			frame@f9023000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9023000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9024000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9024000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9025000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9025000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9026000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9026000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9027000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9027000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9028000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9028000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		sram@fc190000 {
+			compatible = "qcom,msm8226-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		rpm_msg_ram: sram@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xfc428000 0x4000>;
+
+			apss_master_stats: sram@150 {
+				reg = <0x150 0x14>;
+			};
+
+			mpss_master_stats: sram@b50 {
+				reg = <0xb50 0x14>;
+			};
+
+			lpss_master_stats: sram@1550 {
+				reg = <0x1550 0x14>;
+			};
+
+			pronto_master_stats: sram@1f50 {
+				reg = <0x1f50 0x14>;
+			};
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8226-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
+			#hwlock-cells = <1>;
+		};
+
+		adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8226-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			power-domains = <&rpmpd MSM8226_VDDCX>;
+			power-domain-names = "cx";
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 8>;
+				qcom,smd-edge = <1>;
+
+				label = "lpass";
+			};
+		};
+
+		sram@fdd00000 {
+			compatible = "qcom,msm8226-ocmem";
+			reg = <0xfdd00000 0x2000>,
+			      <0xfec00000 0x20000>;
+			reg-names = "ctrl", "mem";
+			ranges = <0 0xfec00000 0x20000>;
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>;
+			clock-names = "core";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gmu_sram: gmu-sram@0 {
+				reg = <0x0 0x20000>;
+			};
+		};
+
+		sram@fe805000 {
+			compatible = "qcom,msm8226-imem", "syscon", "simple-mfd";
+			reg = <0xfe805000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+
+				mode-bootloader = <0x77665500>;
+				mode-normal = <0x77665501>;
+				mode-recovery = <0x77665502>;
+			};
+		};
+
+		mdss: display-subsystem@fd900000 {
+			compatible = "qcom,mdss";
+			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&mmcc MDSS_GDSC>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@fd900000 {
+				compatible = "qcom,msm8226-mdp5", "qcom,mdp5";
+				reg = <0xfd900100 0x22000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_mdp_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@fd922800 {
+				compatible = "qcom,msm8226-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922800 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
+						  <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>,
+							 <&mdss_dsi0_phy 1>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE0_CLK>,
+					 <&mmcc MDSS_PCLK0_CLK>,
+					 <&mmcc MDSS_ESC0_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&mdss_dsi0_phy>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&mdss_mdp_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@fd922a00 {
+				compatible = "qcom,dsi-phy-28nm-8226";
+				reg = <0xfd922a00 0xd4>,
+				      <0xfd922b00 0x280>,
+				      <0xfd922d80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+				clock-names = "iface",
+					      "ref";
+			};
+		};
+
+		gpu: adreno@fdb00000 {
+			compatible = "qcom,adreno-305.18", "qcom,adreno";
+			reg = <0xfdb00000 0x10000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+
+			clocks = <&mmcc OXILI_GFX3D_CLK>,
+				 <&mmcc OXILICX_AHB_CLK>,
+				 <&mmcc OXILICX_AXI_CLK>;
+			clock-names = "core", "iface", "mem_iface";
+
+			sram = <&gmu_sram>;
+			power-domains = <&mmcc OXILICX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-450000000 {
+					opp-hz = /bits/ 64 <450000000>;
+				};
+
+				opp-320000000 {
+					opp-hz = /bits/ 64 <320000000>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+				};
+
+				opp-19000000 {
+					opp-hz = /bits/ 64 <19000000>;
+				};
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
new file mode 100644
index 000000000000..69fe651f564d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8660.dtsi"
+#include "pm8058.dtsi"
+
+/ {
+	model = "Qualcomm MSM8660 SURF";
+	compatible = "qcom,msm8660-surf", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+};
+
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi12_serial {
+	status = "okay";
+};
+
+&pm8058 {
+	interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_FN_F1)
+		MATRIX_KEY(0, 1, KEY_UP)
+		MATRIX_KEY(0, 2, KEY_LEFT)
+		MATRIX_KEY(0, 3, KEY_VOLUMEUP)
+		MATRIX_KEY(1, 0, KEY_FN_F2)
+		MATRIX_KEY(1, 1, KEY_RIGHT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
+		MATRIX_KEY(2, 3, KEY_ENTER)
+		MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(4, 1, KEY_UP)
+		MATRIX_KEY(4, 2, KEY_LEFT)
+		MATRIX_KEY(4, 3, KEY_HOME)
+		MATRIX_KEY(4, 4, KEY_FN_F3)
+		MATRIX_KEY(5, 0, KEY_CAMERA)
+		MATRIX_KEY(5, 1, KEY_RIGHT)
+		MATRIX_KEY(5, 2, KEY_DOWN)
+		MATRIX_KEY(5, 3, KEY_BACK)
+		MATRIX_KEY(5, 4, KEY_MENU)
+		>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
+};
+
+&rpm {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8901-regulators";
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8058-regulators";
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
index ec5cbc468bd3..a7c245b9c8f9 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -36,6 +36,7 @@
 		L2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 		};
 	};
 
@@ -50,41 +51,28 @@
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo-board-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <19200000>;
+			clock-output-names = "cxo_board";
 		};
 
-		pxo_board {
+		pxo_board: pxo-board-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
+			clock-output-names = "pxo_board";
 		};
 
-		sleep_clk {
+		sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
 		};
 	};
 
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&xoadc 0x00 0x01>, /* Battery */
-			    <&xoadc 0x00 0x02>, /* DC in (charger) */
-			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
-			    <&xoadc 0x00 0x0b>, /* Die temperature */
-			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			    <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -115,6 +103,7 @@
 			reg = <0x800000 0x4000>;
 
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 173>;
 			#gpio-cells = <2>;
 			interrupts = <0 16 0x4>;
 			interrupt-controller;
@@ -125,8 +114,62 @@
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-msm8660";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x900000 0x4000>;
+			clocks = <&pxo_board>, <&cxo_board>;
+			clock-names = "pxo", "cxo";
+		};
+
+		gsbi1: gsbi@16000000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16000000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_spi: spi@16080000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16080000 0x1000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+			status = "disabled";
+
+			gsbi3_i2c: i2c@16280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		gsbi6: gsbi@16500000 {
@@ -210,6 +253,7 @@
 			ranges;
 
 			syscon-tcsr = <&tcsr>;
+			status = "disabled";
 
 			gsbi8_i2c: i2c@19880000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
@@ -257,7 +301,7 @@
 			};
 		};
 
-		external-bus@1a100000 {
+		ebi2: external-bus@1a100000 {
 			compatible = "qcom,msm8660-ebi2";
 			#address-cells = <2>;
 			#size-cells = <1>;
@@ -274,217 +318,34 @@
 			status = "disabled";
 		};
 
-		qcom,ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8058: pmic@0 {
-				compatible = "qcom,pm8058";
-				interrupt-parent = <&tlmm>;
-				interrupts = <88 8>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8058_gpio: gpio@150 {
-					compatible = "qcom,pm8058-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8058_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8058_mpps: mpps@50 {
-					compatible = "qcom,pm8058-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					interrupt-parent = <&pm8058>;
-					interrupts =
-					<128 IRQ_TYPE_NONE>,
-					<129 IRQ_TYPE_NONE>,
-					<130 IRQ_TYPE_NONE>,
-					<131 IRQ_TYPE_NONE>,
-					<132 IRQ_TYPE_NONE>,
-					<133 IRQ_TYPE_NONE>,
-					<134 IRQ_TYPE_NONE>,
-					<135 IRQ_TYPE_NONE>,
-					<136 IRQ_TYPE_NONE>,
-					<137 IRQ_TYPE_NONE>,
-					<138 IRQ_TYPE_NONE>,
-					<139 IRQ_TYPE_NONE>;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8058-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				keypad@148 {
-					compatible = "qcom,pm8058-keypad";
-					reg = <0x148>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <74 1>, <75 1>;
-					debounce = <15>;
-					scan-delay = <32>;
-					row-hold = <91500>;
-				};
-
-				xoadc: xoadc@197 {
-					compatible = "qcom,pm8058-adc";
-					reg = <0x197>;
-					interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@0 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@1 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@2 {
-						reg = <0x00 0x02>;
-					};
-					ichg: adc-channel@3 {
-						reg = <0x00 0x03>;
-					};
-					vph_pwr: adc-channel@4 {
-						reg = <0x00 0x04>;
-					};
-					usb_vbus: adc-channel@a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@d {
-						reg = <0x00 0x0d>;
-					};
-					ref_325mv: adc-channel@e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@f {
-						reg = <0x00 0x0f>;
-					};
-				};
-
-				rtc@1e8 {
-					compatible = "qcom,pm8058-rtc";
-					reg = <0x1e8>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <39 1>;
-					allow-set-time;
-				};
-
-				vibrator@4a {
-					compatible = "qcom,pm8058-vib";
-					reg = <0x4a>;
-				};
-			};
 		};
 
 		l2cc: clock-controller@2082000 {
-			compatible	= "syscon";
-			reg		= <0x02082000 0x1000>;
+			compatible = "qcom,kpss-gcc-msm8660", "qcom,kpss-gcc", "syscon";
+			reg = <0x02082000 0x1000>;
 		};
 
 		rpm: rpm@104000 {
-			compatible	= "qcom,rpm-msm8660";
-			reg		= <0x00104000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
-
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			compatible = "qcom,rpm-msm8660";
+			reg = <0x00104000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
 			clock-names = "ram";
 
 			rpmcc: clock-controller {
-				compatible	= "qcom,rpmcc-msm8660", "qcom,rpmcc";
+				compatible = "qcom,rpmcc-msm8660", "qcom,rpmcc";
 				#clock-cells = <1>;
-			};
-
-			pm8901-regulators {
-				compatible = "qcom,rpm-pm8901-regulators";
-
-				pm8901_l0: l0 {};
-				pm8901_l1: l1 {};
-				pm8901_l2: l2 {};
-				pm8901_l3: l3 {};
-				pm8901_l4: l4 {};
-				pm8901_l5: l5 {};
-				pm8901_l6: l6 {};
-
-				/* S0 and S1 Handled as SAW regulators by SPM */
-				pm8901_s2: s2 {};
-				pm8901_s3: s3 {};
-				pm8901_s4: s4 {};
-
-				pm8901_lvs0: lvs0 {};
-				pm8901_lvs1: lvs1 {};
-				pm8901_lvs2: lvs2 {};
-				pm8901_lvs3: lvs3 {};
-
-				pm8901_mvs: mvs {};
-			};
-
-			pm8058-regulators {
-				compatible = "qcom,rpm-pm8058-regulators";
-
-				pm8058_l0: l0 {};
-				pm8058_l1: l1 {};
-				pm8058_l2: l2 {};
-				pm8058_l3: l3 {};
-				pm8058_l4: l4 {};
-				pm8058_l5: l5 {};
-				pm8058_l6: l6 {};
-				pm8058_l7: l7 {};
-				pm8058_l8: l8 {};
-				pm8058_l9: l9 {};
-				pm8058_l10: l10 {};
-				pm8058_l11: l11 {};
-				pm8058_l12: l12 {};
-				pm8058_l13: l13 {};
-				pm8058_l14: l14 {};
-				pm8058_l15: l15 {};
-				pm8058_l16: l16 {};
-				pm8058_l17: l17 {};
-				pm8058_l18: l18 {};
-				pm8058_l19: l19 {};
-				pm8058_l20: l20 {};
-				pm8058_l21: l21 {};
-				pm8058_l22: l22 {};
-				pm8058_l23: l23 {};
-				pm8058_l24: l24 {};
-				pm8058_l25: l25 {};
-
-				pm8058_s0: s0 {};
-				pm8058_s1: s1 {};
-				pm8058_s2: s2 {};
-				pm8058_s3: s3 {};
-				pm8058_s4: s4 {};
-
-				pm8058_lvs0: lvs0 {};
-				pm8058_lvs1: lvs1 {};
-
-				pm8058_ncp: ncp {};
+				clocks = <&pxo_board>;
+				clock-names = "pxo";
 			};
 		};
 
@@ -493,81 +354,76 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
-			sdcc1: sdcc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x8000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <48000000>;
+				reg = <0x12400000 0x8000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
-			sdcc2: sdcc@12140000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+			sdcc2: mmc@12140000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12140000 0x8000>;
-				interrupts	= <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <48000000>;
+				reg = <0x12140000 0x8000>;
+				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
-			sdcc3: sdcc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x8000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12180000 0x8000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 				no-1-8-v;
 			};
 
-			sdcc4: sdcc@121c0000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+			sdcc4: mmc@121c0000 {
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x121c0000 0x8000>;
-				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				max-frequency	= <48000000>;
+				status = "disabled";
+				reg = <0x121c0000 0x8000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
+				max-frequency = <48000000>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
-			sdcc5: sdcc@12200000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+			sdcc5: mmc@12200000 {
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12200000 0x8000>;
-				interrupts	= <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12200000 0x8000>;
+				interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts
new file mode 100644
index 000000000000..c8d34de8a71e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e5.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts
new file mode 100644
index 000000000000..85be286c8608
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e7.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts
new file mode 100644
index 000000000000..d3abe0536238
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-grandmax.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts
new file mode 100644
index 000000000000..dee2c20af355
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-serranove.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi
new file mode 100644
index 000000000000..36328dbe4212
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/ {
+	cpus {
+		cpu@0 {
+			enable-method = "qcom,msm8916-smp";
+		};
+		cpu@1 {
+			enable-method = "qcom,msm8916-smp";
+		};
+		cpu@2 {
+			enable-method = "qcom,msm8916-smp";
+		};
+		cpu@3 {
+			enable-method = "qcom,msm8916-smp";
+		};
+
+		idle-states {
+			/delete-property/ entry-method;
+		};
+	};
+
+	psci {
+		status = "disabled";
+	};
+};
+
+&CPU_SLEEP_0 {
+	compatible = "qcom,idle-state-spc";
+};
+
+&cpu0_acc {
+	status = "okay";
+};
+
+&cpu0_saw {
+	status = "okay";
+};
+
+&cpu1_acc {
+	status = "okay";
+};
+
+&cpu1_saw {
+	status = "okay";
+};
+
+&cpu2_acc {
+	status = "okay";
+};
+
+&cpu2_saw {
+	status = "okay";
+};
+
+&cpu3_acc {
+	status = "okay";
+};
+
+&cpu3_saw {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-htc-memul.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-htc-memul.dts
new file mode 100644
index 000000000000..ed328b24335f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-htc-memul.dts
@@ -0,0 +1,372 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &smem_region;
+
+/ {
+	model = "HTC One Mini 2";
+	compatible = "htc,memul", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		unknown@5b00000 {
+			reg = <0x05b00000 0x200000>;
+			no-map;
+		};
+
+		unknown@7500000 {
+			reg = <0x07500000 0xb00000>;
+			no-map;
+		};
+
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x4f00000>;
+			no-map;
+		};
+
+		unknown@cf00000 {
+			reg = <0x0cf00000 0x200000>;
+			no-map;
+		};
+
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x3a000>;
+			no-map;
+		};
+
+		unknown@d13a000 {
+			reg = <0x0d13a000 0xc6000>;
+			no-map;
+		};
+
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0x650000>;
+			no-map;
+		};
+
+		unknown@d850000 {
+			reg = <0x0d850000 0x3b0000>;
+			no-map;
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1400000>;
+			no-map;
+		};
+
+		unknown@f000000 {
+			reg = <0x0f000000 0x500000>;
+			no-map;
+		};
+
+		venus_region: venus@f500000 {
+			reg = <0x0f500000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		unknown@fb00000 {
+			reg = <0x0fb00000 0x1b00000>;
+			no-map;
+		};
+	};
+};
+
+&adsp {
+	firmware-name = "qcom/msm8926/memul/adsp.mbn";
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	magnetometer@d {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0x0d>;
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_RISING>;
+		vdd-supply = <&pm8226_l19>;
+		vid-supply = <&pm8226_l28>;
+	};
+
+	accelerometer@18 {
+		compatible = "bosch,bma250e";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_RISING>;
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_l28>;
+	};
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	/* TFA9887 @ 34 */
+	/* TFA9887 @ 35 */
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+
+		syna,startup-delay-ms = <160>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	/* NCP6924 Camera Regulators @ 10 */
+	/* PN544 NFC @ 28 */
+	/* TPS61310 Flash/Torch @ 33 */
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1750000>;
+	qcom,fast-charge-current-limit = <1750000>;
+	qcom,fast-charge-safe-voltage = <4360000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4300000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-superman-lte.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-superman-lte.dts
new file mode 100644
index 000000000000..9b48661d69c5
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-superman-lte.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/* This device has touchscreen on i2c3 instead */
+/delete-node/ &touchscreen;
+
+/ {
+	model = "Nokia Lumia 735";
+	compatible = "microsoft,superman-lte", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	touchscreen: touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c5 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-tesla.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-tesla.dts
new file mode 100644
index 000000000000..53a6d4e85959
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-tesla.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/* This device has touchscreen on i2c1 instead */
+/delete-node/ &touchscreen;
+
+/ {
+	model = "Nokia Lumia 830";
+	compatible = "microsoft,tesla", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	touchscreen: touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c5 {
+	status = "disabled";
+};
+
+&gpio_keys {
+	key-camera-snapshot {
+		label = "Camera Snapshot";
+		gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+		linux,code = <KEY_CAMERA>;
+	};
+
+	key-camera-focus {
+		label = "Camera Focus";
+		gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+		linux,code = <KEY_CAMERA_FOCUS>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
new file mode 100644
index 000000000000..0cbe2d2fbbb1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &smem_region;
+
+/ {
+	model = "Motorola Moto G 4G (2013)";
+	compatible = "motorola,peregrine", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	sensor@48 {
+		compatible = "ti,tmp108";
+		reg = <0x48>;
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&pm8226_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-boot-on;
+		};
+
+		pm8226_lvs1: lvs1 {
+			/* Pull-up for I2C lines */
+			regulator-always-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>;
+
+	status = "okay";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <2000000>;
+	qcom,fast-charge-current-limit = <1900000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
new file mode 100644
index 000000000000..36f4c997b0b3
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8960.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Qualcomm MSM8960 CDP";
+	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ext_l2: gpio-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ext_l2";
+		gpio = <&msmgpio 91 0>;
+		startup-delay-us = <10000>;
+		enable-active-high;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_default>;
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+
+	ethernet@0 {
+		compatible = "micrel,ks8851";
+		reg = <0>;
+		interrupt-parent = <&msmgpio>;
+		interrupts = <90 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <5400000>;
+		vdd-supply = <&ext_l2>;
+		vdd-io-supply = <&pm8921_lvs6>;
+		reset-gpios = <&msmgpio 89 0>;
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&msmgpio {
+	spi1_default: spi1-default-state {
+		 mosi-pins {
+			pins = "gpio6";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 miso-pins {
+			pins = "gpio7";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 cs-pins {
+			pins = "gpio8";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		 };
+
+		 clk-pins {
+			pins = "gpio9";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+	};
+};
+
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(0, 3, KEY_CAMERA)
+		>;
+	keypad,num-rows = <1>;
+	keypad,num-columns = <5>;
+
+	status = "okay";
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
new file mode 100644
index 000000000000..1a5116336ff0
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
@@ -0,0 +1,336 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+
+#include "qcom-msm8960.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Samsung Galaxy Express SGH-I437";
+	compatible = "samsung,expressatt", "qcom,msm8960";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+		mmc0 = &sdcc1; /* SDCC1 eMMC slot */
+		mmc1 = &sdcc3; /* SDCC3 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	vqmmc-supply = <&pm8921_l7>;
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-0 = <&spi1_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+};
+
+&msmgpio {
+	spi1_default: spi1-default-state {
+		mosi-pins {
+			pins = "gpio6";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		miso-pins {
+			pins = "gpio7";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		cs-pins {
+			pins = "gpio8";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		};
+
+		clk-pins {
+			pins = "gpio9";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3100000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index f2aeaccdc1ad..f420740e068e 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -3,6 +3,8 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
 #include <dt-bindings/mfd/qcom-rpm.h>
 #include <dt-bindings/soc/qcom,gsbi.h>
 
@@ -16,7 +18,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		interrupts = <1 14 0x304>;
+		interrupts = <GIC_PPI 14 0x304>;
 
 		cpu@0 {
 			compatible = "qcom,krait";
@@ -41,6 +43,7 @@
 		L2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 		};
 	};
 
@@ -51,26 +54,26 @@
 
 	cpu-pmu {
 		compatible = "qcom,krait-pmu";
-		interrupts = <1 10 0x304>;
+		interrupts = <GIC_PPI 10 0x304>;
 		qcom,no-pc-write;
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <19200000>;
 			clock-output-names = "cxo_board";
 		};
 
-		pxo_board {
+		pxo_board: pxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
 			clock-output-names = "pxo_board";
 		};
 
-		sleep_clk {
+		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
@@ -78,6 +81,15 @@
 		};
 	};
 
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -93,22 +105,22 @@
 		};
 
 		timer@200a000 {
-			compatible = "qcom,kpss-timer",
-				     "qcom,kpss-wdt-msm8960", "qcom,msm-timer";
-			interrupts = <1 1 0x301>,
-				     <1 2 0x301>,
-				     <1 3 0x301>;
+			compatible = "qcom,kpss-wdt-msm8960", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 0x301>,
+				     <GIC_PPI 2 0x301>,
+				     <GIC_PPI 3 0x301>;
 			reg = <0x0200a000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
+			clock-frequency = <27000000>;
 			cpu-offset = <0x80000>;
 		};
 
 		msmgpio: pinctrl@800000 {
 			compatible = "qcom,msm8960-pinctrl";
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 152>;
 			#gpio-cells = <2>;
-			interrupts = <0 16 0x4>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			reg = <0x800000 0x4000>;
@@ -117,8 +129,13 @@
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-msm8960";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x900000 0x4000>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
 		};
 
 		lcc: clock-controller@28000000 {
@@ -126,41 +143,81 @@
 			reg = <0x28000000 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
 		};
 
 		clock-controller@4000000 {
 			compatible = "qcom,mmcc-msm8960";
 			reg = <0x4000000 0x1000>;
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
 		};
 
 		l2cc: clock-controller@2011000 {
-			compatible	= "syscon";
-			reg		= <0x2011000 0x1000>;
+			compatible = "qcom,kpss-gcc-msm8960", "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
 		};
 
-		rpm@108000 {
-			compatible	= "qcom,rpm-msm8960";
-			reg		= <0x108000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-msm8960";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
 
-			interrupts	= <0 19 0>, <0 21 0>, <0 22 0>;
-			interrupt-names	= "ack", "err", "wakeup";
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-			};
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 		};
 
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
 		};
 
 		acc1: clock-controller@2098000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
 		};
 
 		saw0: regulator@2089000 {
@@ -191,54 +248,17 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x16440000 0x1000>,
 				      <0x16400000 0x1000>;
-				interrupts = <0 154 0x0>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
 			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pmicintc: pmic@0 {
-				compatible = "qcom,pm8921";
-				interrupt-parent = <&msmgpio>;
-				interrupts = <104 8>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				keypad@148 {
-					compatible = "qcom,pm8921-keypad";
-					reg = <0x148>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <74 1>, <75 1>;
-					debounce = <15>;
-					scan-delay = <32>;
-					row-hold = <91500>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <39 1>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-			};
 		};
 
 		rng@1a500000 {
@@ -248,53 +268,36 @@
 			clock-names = "core";
 		};
 
-		/* Temporary fixed regulator */
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x8000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: sdcc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x8000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-
-			sdcc3: sdcc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x8000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency	= <192000000>;
-				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
-			};
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x8000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
 		};
 
 		tcsr: syscon@1a400000 {
@@ -302,7 +305,7 @@
 			reg = <0x1a400000 0x100>;
 		};
 
-		gsbi@16000000 {
+		gsbi1: gsbi@16000000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <1>;
 			reg = <0x16000000 0x100>;
@@ -312,13 +315,12 @@
 			#size-cells = <1>;
 			ranges;
 
-			spi@16080000 {
+			gsbi1_spi: spi@16080000 {
 				compatible = "qcom,spi-qup-v1.1.1";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x16080000 0x1000>;
-				interrupts = <0 147 0>;
-				spi-max-frequency = <24000000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
 				cs-gpios = <&msmgpio 8 0>;
 
 				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
@@ -326,5 +328,36 @@
 				status = "disabled";
 			};
 		};
+
+		usb1: usb@12500000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			#reset-cells = <1>;
+			status = "disabled";
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8960",
+						     "qcom,usb-hs-phy";
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+					#phy-cells = <0>;
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
new file mode 100644
index 000000000000..4aaae8537a3f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -0,0 +1,725 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "LGE MSM 8974 HAMMERHEAD";
+	compatible = "lge,hammerhead", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp2_uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	clk_pwm: pwm {
+		compatible = "clk-pwm";
+		clocks = <&mmcc CAMSS_GP1_CLK>;
+
+		pinctrl-0 = <&vibrator_pin>;
+		pinctrl-names = "default";
+
+		#pwm-cells = <2>;
+	};
+
+	vibrator {
+		compatible = "pwm-vibrator";
+		pwms = <&clk_pwm 0 100000>;
+		pwm-names = "enable";
+
+		vcc-supply = <&pm8941_l19>;
+		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_pin>;
+	};
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	charger: bq24192@6b {
+		compatible = "ti,bq24192";
+		reg = <0x6b>;
+		interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+
+		omit-battery-class;
+
+		usb_otg_vbus: usb-otg-vbus { };
+	};
+
+	fuelgauge: max17048@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x4d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
+
+		maxim,alert-low-soc-level = <2>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@70 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x70>;
+
+		interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	avago_apds993@39 {
+		compatible = "avago,apds9930";
+		reg = <0x39>;
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l17>;
+		vddio-supply = <&pm8941_lvs1>;
+		led-max-microamp = <100000>;
+		amstaos,proximity-diodes = <0>;
+	};
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	led-controller@38 {
+		compatible = "ti,lm3630a";
+		status = "okay";
+		reg = <0x38>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 1>;
+			label = "lcd-backlight";
+			default-brightness = <200>;
+		};
+	};
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	mpu6515@68 {
+		compatible = "invensense,mpu6515";
+		reg = <0x68>;
+		interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
+		vddio-supply = <&pm8941_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu6515_pin>;
+
+		mount-matrix = "0", "-1", "0",
+				"-1", "0", "0",
+				"0", "0", "1";
+
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ak8963@f {
+				compatible = "asahi-kasei,ak8963";
+				reg = <0x0f>;
+				gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+				vid-supply = <&pm8941_lvs1>;
+				vdd-supply = <&pm8941_l17>;
+			};
+
+			bmp280@76 {
+				compatible = "bosch,bmp280";
+				reg = <0x76>;
+				vdda-supply = <&pm8941_lvs1>;
+				vddd-supply = <&pm8941_l17>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+};
+
+&blsp2_uart4 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pin>;
+
+		host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_lvs3>;
+	vddio-supply = <&pm8941_l12>;
+
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "lg,acx467akm-7";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_pin>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pm8941_l12>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio9";
+		function = "normal";
+
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
+
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio17";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	otg {
+		gpio-hog;
+		gpios = <35 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "otg-gpio";
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <815000>;
+			regulator-max-microvolt = <900000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs1: lvs1 {};
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8941_s3>;
+	non-removable;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	bcrmf@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		brcm,drive-strength = <10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	mpu6515_pin: mpu6515-state {
+		pins = "gpio73";
+		function = "gpio";
+		bias-disable;
+	};
+
+	touch_pin: touch-state {
+		int-pins {
+			pins = "gpio5";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		reset-pins {
+			pins = "gpio8";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	panel_pin: panel-state {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bt_pin: bt-state {
+		hostwake-pins {
+			pins = "gpio42";
+			function = "gpio";
+		};
+
+		devwake-pins {
+			pins = "gpio62";
+			function = "gpio";
+		};
+
+		shutdown-pins {
+			pins = "gpio41";
+			function = "gpio";
+		};
+	};
+
+	vibrator_pin: vibrator-state {
+		core-pins {
+			pins = "gpio27";
+			function = "gp1_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		enable-pins {
+			pins = "gpio60";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	extcon = <&charger>, <&usb_id>;
+	vbus-supply = <&usb_otg_vbus>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts
new file mode 100644
index 000000000000..9f2ab5c122d0
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1 Compact";
+	compatible = "sony,xperia-amami", "qcom,msm8974";
+	chassis-type = "handset";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1300000>;
+	qcom,fast-charge-current-limit = <1300000>;
+	qcom,dc-current-limit = <1300000>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts
new file mode 100644
index 000000000000..9028f17e5c4a
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1";
+	compatible = "sony,xperia-honami", "qcom,msm8974";
+	chassis-type = "handset";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
new file mode 100644
index 000000000000..d34659ebac22
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -0,0 +1,526 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@3e8e0000 {
+			compatible = "ramoops";
+			reg = <0x3e8e0000 0x200000>;
+
+			console-size = <0x100000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x80000>;
+		};
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <10>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			touchscreen-inverted-x;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	nfc@28 {
+		compatible = "nxp,pn544-i2c";
+		reg = <0x28>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <59 IRQ_TYPE_EDGE_RISING>;
+
+		enable-gpios = <&pm8941_gpios 23 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	/* sii8334 MHL HDMI bridge */
+};
+
+&pm8941_coincell {
+	status = "okay";
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio4", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&pm8941_wled {
+	status = "okay";
+
+	qcom,cs-out;
+	qcom,current-limit = <20>;
+	qcom,current-boost-limit = <805>;
+	qcom,switching-freq = <1600>;
+	qcom,ovp = <29>;
+	qcom,num-strings = <2>;
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	ts_int_pin: touch-int-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
new file mode 100644
index 000000000000..b1413983787c
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
@@ -0,0 +1,2412 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interconnect/qcom,msm8974.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_PPI 9 0xf04>;
+
+		CPU0: cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU1: cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU2: cpu@2 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <2>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU3: cpu@3 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <3>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+			qcom,saw = <&saw_l2>;
+		};
+
+		idle-states {
+			CPU_SPC: spc {
+				compatible = "qcom,idle-state-spc",
+						"arm,idle-state";
+				entry-latency-us = <150>;
+				exit-latency-us = <200>;
+				min-residency-us = <2000>;
+			};
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8974", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 7 0xf04>;
+	};
+
+	rpm: remoteproc {
+		compatible = "qcom,msm8974-rpm-proc", "qcom,rpm-proc";
+
+		master-stats {
+			compatible = "qcom,rpm-master-stats";
+			qcom,rpm-msg-ram = <&apss_master_stats>,
+					   <&mpss_master_stats>,
+					   <&lpss_master_stats>,
+					   <&pronto_master_stats>;
+			qcom,master-names = "APSS",
+					    "MPSS",
+					    "LPSS",
+					    "PRONTO";
+		};
+
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8974";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x5100000>;
+			no-map;
+		};
+
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x100000>;
+			no-map;
+		};
+
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0xa00000>;
+			no-map;
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
+		};
+
+		venus_region: memory@f500000 {
+			reg = <0x0f500000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0xfa00000 0x200000>;
+			no-map;
+		};
+
+		tz_region: memory@fc00000 {
+			reg = <0x0fc00000 0x160000>;
+			no-map;
+		};
+
+		rfsa_mem: memory@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+
+		memory-region = <&smem_region>;
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-wcnss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs 8 13>;
+		qcom,ipc-2 = <&apcs 8 9>;
+		qcom,ipc-3 = <&apcs 8 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smsm: modem@1 {
+			reg = <1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		adsp_smsm: adsp@2 {
+			reg = <2>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@7 {
+			reg = <7>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@f9000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0xf9000000 0x1000>,
+			      <0xf9002000 0x1000>;
+		};
+
+		apcs: syscon@f9011000 {
+			compatible = "syscon";
+			reg = <0xf9011000 0x1000>;
+		};
+
+		saw_l2: power-controller@f9012000 {
+			compatible = "qcom,saw2";
+			reg = <0xf9012000 0x1000>;
+			regulator;
+		};
+
+		watchdog@f9017000 {
+			compatible = "qcom,apss-wdt-msm8974", "qcom,kpss-wdt";
+			reg = <0xf9017000 0x1000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@f9020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xf9020000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@f9021000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9021000 0x1000>,
+				      <0xf9022000 0x1000>;
+			};
+
+			frame@f9023000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9023000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9024000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9024000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9025000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9025000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9026000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9026000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9027000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9027000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9028000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9028000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		acc0: power-manager@f9088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw0: power-controller@f9089000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		acc1: power-manager@f9098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw1: power-controller@f9099000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		acc2: power-manager@f90a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw2: power-controller@f90a9000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		acc3: power-manager@f90b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw3: power-controller@f90b9000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <8>;
+			non-removable;
+
+			status = "disabled";
+		};
+
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@f991d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991d000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@f991e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991e000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@f9923000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c1_default>;
+			pinctrl-1 = <&blsp1_i2c1_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c2_default>;
+			pinctrl-1 = <&blsp1_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c3_default>;
+			pinctrl-1 = <&blsp1_i2c3_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@f9928000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9928000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c6_default>;
+			pinctrl-1 = <&blsp1_i2c6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_dma: dma-controller@f9944000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xf9944000 0x19000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		blsp2_uart1: serial@f995d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf995d000 0x1000>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART1_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart1_default>;
+			pinctrl-1 = <&blsp2_uart1_sleep>;
+			status = "disabled";
+		};
+
+		blsp2_uart2: serial@f995e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf995e000 0x1000>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp2_uart4: serial@f9960000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf9960000 0x1000>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART4_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp2_uart4_default>;
+			status = "disabled";
+		};
+
+		blsp2_i2c2: i2c@f9964000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9964000 0x1000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c2_default>;
+			pinctrl-1 = <&blsp2_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c5: i2c@f9967000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9967000 0x1000>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c5_default>;
+			pinctrl-1 = <&blsp2_i2c5_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c6: i2c@f9968000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9968000 0x1000>;
+			interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c6_default>;
+			pinctrl-1 = <&blsp2_i2c6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy-0 {
+					compatible = "qcom,usb-hs-phy-msm8974",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					status = "disabled";
+				};
+
+				usb_hs2_phy: phy-1 {
+					compatible = "qcom,usb-hs-phy-msm8974",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2B_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2B_PHY_BCR>, <&usb 1>;
+					reset-names = "phy", "por";
+					status = "disabled";
+				};
+			};
+		};
+
+		rng@f9bff000 {
+			compatible = "qcom,prng";
+			reg = <0xf9bff000 0x200>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		pronto: remoteproc@fb204000 {
+			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+			reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			memory-region = <&wcnss_region>;
+
+			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			iris {
+				compatible = "qcom,wcn3680";
+
+				clocks = <&rpmcc RPM_SMD_CXO_A2>;
+				clock-names = "xo";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 17>;
+				qcom,smd-edge = <6>;
+
+				wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+					status = "disabled";
+
+					qcom,mmio = <&pronto>;
+
+					bluetooth {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>,
+							     <GIC_SPI 146 IRQ_TYPE_EDGE_RISING>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable",
+									"tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		sram@fc190000 {
+			compatible = "qcom,msm8974-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		etf@fc307000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0xfc307000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint = <&replicator_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					etf_in: endpoint {
+						remote-endpoint = <&merger_out>;
+					};
+				};
+			};
+		};
+
+		tpiu@fc318000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0xfc318000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					tpiu_in: endpoint {
+						remote-endpoint = <&replicator_out1>;
+					};
+				 };
+			};
+		};
+
+		funnel@fc31a000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc31a000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * Not described input ports:
+				 * 0 - not-connected
+				 * 1 - connected trought funnel to Multimedia CPU
+				 * 2 - connected to Wireless CPU
+				 * 3 - not-connected
+				 * 4 - not-connected
+				 * 6 - not-connected
+				 * 7 - connected to STM
+				 */
+				port@5 {
+					reg = <5>;
+					funnel1_in5: endpoint {
+						remote-endpoint = <&kpss_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					funnel1_out: endpoint {
+						remote-endpoint = <&merger_in1>;
+					};
+				};
+			};
+		};
+
+		funnel@fc31b000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc31b000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * Not described input ports:
+				 * 0 - connected trought funnel to Audio, Modem and
+				 *     Resource and Power Manager CPU's
+				 * 2...7 - not-connected
+				 */
+				port@1 {
+					reg = <1>;
+					merger_in1: endpoint {
+						remote-endpoint = <&funnel1_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					merger_out: endpoint {
+						remote-endpoint = <&etf_in>;
+					};
+				};
+			};
+		};
+
+		replicator@fc31c000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0xfc31c000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					replicator_out0: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					replicator_out1: endpoint {
+						remote-endpoint = <&tpiu_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint = <&etf_out>;
+					};
+				};
+			};
+		};
+
+		etr@fc322000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0xfc322000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					etr_in: endpoint {
+						remote-endpoint = <&replicator_out0>;
+					};
+				};
+			};
+		};
+
+		etm@fc33c000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33c000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU0>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint = <&kpss_in0>;
+					};
+				};
+			};
+		};
+
+		etm@fc33d000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33d000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU1>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint = <&kpss_in1>;
+					};
+				};
+			};
+		};
+
+		etm@fc33e000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33e000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU2>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint = <&kpss_in2>;
+					};
+				};
+			};
+		};
+
+		etm@fc33f000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33f000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU3>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint = <&kpss_in3>;
+					};
+				};
+			};
+		};
+
+		/* KPSS funnel, only 4 inputs are used */
+		funnel@fc345000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc345000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					kpss_in0: endpoint {
+						remote-endpoint = <&etm0_out>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					kpss_in1: endpoint {
+						remote-endpoint = <&etm1_out>;
+					};
+				};
+				port@2 {
+					reg = <2>;
+					kpss_in2: endpoint {
+						remote-endpoint = <&etm2_out>;
+					};
+				};
+				port@3 {
+					reg = <3>;
+					kpss_in3: endpoint {
+						remote-endpoint = <&etm3_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					kpss_out: endpoint {
+						remote-endpoint = <&funnel1_in5>;
+					};
+				};
+			};
+		};
+
+		bimc: interconnect@fc380000 {
+			reg = <0xfc380000 0x6a000>;
+			compatible = "qcom,msm8974-bimc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+				 <&rpmcc RPM_SMD_BIMC_A_CLK>;
+		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfc400000 0x4000>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&sleep_clk>;
+			clock-names = "xo",
+				      "sleep_clk";
+		};
+
+		rpm_msg_ram: sram@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xfc428000 0x4000>;
+
+			apss_master_stats: sram@150 {
+				reg = <0x150 0x14>;
+			};
+
+			mpss_master_stats: sram@b50 {
+				reg = <0xb50 0x14>;
+			};
+
+			lpss_master_stats: sram@1550 {
+				reg = <0x1550 0x14>;
+			};
+
+			pronto_master_stats: sram@1f50 {
+				reg = <0x1f50 0x14>;
+			};
+		};
+
+		snoc: interconnect@fc460000 {
+			reg = <0xfc460000 0x4000>;
+			compatible = "qcom,msm8974-snoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+				 <&rpmcc RPM_SMD_SNOC_A_CLK>;
+		};
+
+		pnoc: interconnect@fc468000 {
+			reg = <0xfc468000 0x4000>;
+			compatible = "qcom,msm8974-pnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_PNOC_CLK>,
+				 <&rpmcc RPM_SMD_PNOC_A_CLK>;
+		};
+
+		ocmemnoc: interconnect@fc470000 {
+			reg = <0xfc470000 0x4000>;
+			compatible = "qcom,msm8974-ocmemnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+				 <&rpmcc RPM_SMD_OCMEMGX_A_CLK>;
+		};
+
+		mmssnoc: interconnect@fc478000 {
+			reg = <0xfc478000 0x4000>;
+			compatible = "qcom,msm8974-mmssnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&mmcc MMSS_S0_AXI_CLK>,
+				 <&mmcc MMSS_S0_AXI_CLK>;
+		};
+
+		cnoc: interconnect@fc480000 {
+			reg = <0xfc480000 0x4000>;
+			compatible = "qcom,msm8974-cnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_CNOC_CLK>,
+				 <&rpmcc RPM_SMD_CNOC_A_CLK>;
+		};
+
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_use_backup>,
+				      <&tsens_mode_backup>,
+				      <&tsens_base1_backup>, <&tsens_base2_backup>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>,
+				      <&tsens_s10_p1>, <&tsens_s10_p2>,
+				      <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
+				      <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
+				      <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
+				      <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
+				      <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
+				      <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
+				      <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
+				      <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
+				      <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
+				      <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
+				      <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "use_backup",
+					   "mode_backup",
+					   "base1_backup", "base2_backup",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2",
+					   "s10_p1", "s10_p2",
+					   "s0_p1_backup", "s0_p2_backup",
+					   "s1_p1_backup", "s1_p2_backup",
+					   "s2_p1_backup", "s2_p2_backup",
+					   "s3_p1_backup", "s3_p2_backup",
+					   "s4_p1_backup", "s4_p2_backup",
+					   "s5_p1_backup", "s5_p2_backup",
+					   "s6_p1_backup", "s6_p2_backup",
+					   "s7_p1_backup", "s7_p2_backup",
+					   "s8_p1_backup", "s8_p2_backup",
+					   "s9_p1_backup", "s9_p2_backup",
+					   "s10_p1_backup", "s10_p2_backup";
+			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,msm8974-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1: s0-p1@d1 {
+				reg = <0xd1 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1: s1-p1@d2 {
+				reg = <0xd1 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1: s2-p1@d2 {
+				reg = <0xd2 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1: s3-p1@d3 {
+				reg = <0xd3 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1: s4-p1@d4 {
+				reg = <0xd4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1: s5-p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@d5 {
+				reg = <0xd5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1: s7-p1@d6 {
+				reg = <0xd6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s8_p1: s8-p1@d7 {
+				reg = <0xd7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_mode: mode@d7 {
+				reg = <0xd7 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s9_p1: s9-p1@d8 {
+				reg = <0xd8 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s10_p1: s10_p1@d8 {
+				reg = <0xd8 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_base2: base2@d9 {
+				reg = <0xd9 0x2>;
+				bits = <4 8>;
+			};
+
+			tsens_s0_p2: s0-p2@da {
+				reg = <0xda 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s1_p2: s1-p2@db {
+				reg = <0xdb 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s2_p2: s2-p2@dc {
+				reg = <0xdc 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s3_p2: s3-p2@dc {
+				reg = <0xdc 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s4_p2: s4-p2@dd {
+				reg = <0xdd 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@de {
+				reg = <0xde 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@df {
+				reg = <0xdf 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@e0 {
+				reg = <0xe0 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s8_p2: s8-p2@e0 {
+				reg = <0xe0 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s9_p2: s9-p2@e1 {
+				reg = <0xe1 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s10_p2: s10_p2@e2 {
+				reg = <0xe2 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p2_backup: s5-p2_backup@e3 {
+				reg = <0xe3 0x2>;
+				bits = <0 6>;
+			};
+
+			tsens_mode_backup: mode_backup@e3 {
+				reg = <0xe3 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s6_p2_backup: s6-p2_backup@e4 {
+				reg = <0xe4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2_backup: s7-p2_backup@e4 {
+				reg = <0xe4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p2_backup: s8-p2_backup@e5 {
+				reg = <0xe5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s9_p2_backup: s9-p2_backup@e6 {
+				reg = <0xe6 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s10_p2_backup: s10_p2_backup@e7 {
+				reg = <0xe7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_base1_backup: base1_backup@440 {
+				reg = <0x440 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1_backup: s0-p1_backup@441 {
+				reg = <0x441 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1_backup: s1-p1_backup@442 {
+				reg = <0x441 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1_backup: s2-p1_backup@442 {
+				reg = <0x442 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1_backup: s3-p1_backup@443 {
+				reg = <0x443 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1_backup: s4-p1_backup@444 {
+				reg = <0x444 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1_backup: s5-p1_backup@444 {
+				reg = <0x444 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1_backup: s6-p1_backup@445 {
+				reg = <0x445 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1_backup: s7-p1_backup@446 {
+				reg = <0x446 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_use_backup: use_backup@447 {
+				reg = <0x447 0x1>;
+				bits = <5 3>;
+			};
+
+			tsens_s8_p1_backup: s8-p1_backup@448 {
+				reg = <0x448 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p1_backup: s9-p1_backup@448 {
+				reg = <0x448 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s10_p1_backup: s10_p1_backup@449 {
+				reg = <0x449 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2_backup: base2_backup@44a {
+				reg = <0x44a 0x2>;
+				bits = <2 8>;
+			};
+
+			tsens_s0_p2_backup: s0-p2_backup@44b {
+				reg = <0x44b 0x3>;
+				bits = <2 6>;
+			};
+
+			tsens_s1_p2_backup: s1-p2_backup@44c {
+				reg = <0x44c 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p2_backup: s2-p2_backup@44c {
+				reg = <0x44c 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p2_backup: s3-p2_backup@44d {
+				reg = <0x44d 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p2_backup: s4-p2_backup@44e {
+				reg = <0x44e 0x1>;
+				bits = <2 6>;
+			};
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		bam_dmux_dma: dma-controller@fc834000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xfc834000 0x7000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+		};
+
+		remoteproc_mss: remoteproc@fc880000 {
+			compatible = "qcom,msm8974-mss-pil";
+			reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+				 <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "bus", "mem", "xo";
+
+			resets = <&gcc GCC_MSS_RESTART>;
+			reset-names = "mss_restart";
+
+			qcom,halt-regs = <&tcsr_mutex 0x1180 0x1200 0x1280>;
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			mba {
+				memory-region = <&mba_region>;
+			};
+
+			mpss {
+				memory-region = <&mpss_region>;
+			};
+
+			bam_dmux: bam-dmux {
+				compatible = "qcom,bam-dmux";
+
+				interrupt-parent = <&modem_smsm>;
+				interrupts = <1 IRQ_TYPE_EDGE_BOTH>, <11 IRQ_TYPE_EDGE_BOTH>;
+				interrupt-names = "pc", "pc-ack";
+
+				qcom,smem-states = <&apps_smsm 1>, <&apps_smsm 11>;
+				qcom,smem-state-names = "pc", "pc-ack";
+
+				dmas = <&bam_dmux_dma 4>, <&bam_dmux_dma 5>;
+				dma-names = "tx", "rx";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 12>;
+				qcom,smd-edge = <0>;
+
+				label = "modem";
+			};
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8974-tcsr-mutex", "qcom,tcsr-mutex", "syscon";
+			reg = <0xfd484000 0x2000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@fd4a0000 {
+			compatible = "qcom,tcsr-msm8974", "syscon";
+			reg = <0xfd4a0000 0x10000>;
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,msm8974-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 146>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			sdc1_off: sdc1-off-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+			};
+
+			sdc2_off: sdc2-off-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+			};
+
+			blsp1_uart2_default: blsp1-uart2-default-state {
+				rx-pins {
+					pins = "gpio5";
+					function = "blsp_uart2";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				tx-pins {
+					pins = "gpio4";
+					function = "blsp_uart2";
+					drive-strength = <4>;
+					bias-disable;
+				};
+			};
+
+			blsp2_uart1_default: blsp2-uart1-default-state {
+				tx-rts-pins {
+					pins = "gpio41", "gpio44";
+					function = "blsp_uart7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-cts-pins {
+					pins = "gpio42", "gpio43";
+					function = "blsp_uart7";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			blsp2_uart1_sleep: blsp2-uart1-sleep-state {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			blsp2_uart4_default: blsp2-uart4-default-state {
+				tx-rts-pins {
+					pins = "gpio53", "gpio56";
+					function = "blsp_uart10";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-cts-pins {
+					pins = "gpio54", "gpio55";
+					function = "blsp_uart10";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			blsp1_i2c1_default: blsp1-i2c1-default-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c1_sleep: blsp1-i2c1-sleep-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp1_i2c2_default: blsp1-i2c2-default-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c2_sleep: blsp1-i2c2-sleep-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp1_i2c3_default: blsp1-i2c3-default-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c3_sleep: blsp1-i2c3-sleep-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			/* BLSP1_I2C4 info is missing */
+
+			/* BLSP1_I2C5 info is missing */
+
+			blsp1_i2c6_default: blsp1-i2c6-default-state {
+				pins = "gpio29", "gpio30";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c6_sleep: blsp1-i2c6-sleep-state {
+				pins = "gpio29", "gpio30";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+			/* 6 interfaces per QUP, BLSP2 indexes are numbered (n)+6 */
+
+			/* BLSP2_I2C1 info is missing */
+
+			blsp2_i2c2_default: blsp2-i2c2-default-state {
+				pins = "gpio47", "gpio48";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c2_sleep: blsp2-i2c2-sleep-state {
+				pins = "gpio47", "gpio48";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			/* BLSP2_I2C3 info is missing */
+
+			/* BLSP2_I2C4 info is missing */
+
+			blsp2_i2c5_default: blsp2-i2c5-default-state {
+				pins = "gpio83", "gpio84";
+				function = "blsp_i2c11";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c5_sleep: blsp2-i2c5-sleep-state {
+				pins = "gpio83", "gpio84";
+				function = "blsp_i2c11";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp2_i2c6_default: blsp2-i2c6-default-state {
+				pins = "gpio87", "gpio88";
+				function = "blsp_i2c12";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c6_sleep: blsp2-i2c6-sleep-state {
+				pins = "gpio87", "gpio88";
+				function = "blsp_i2c12";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci_default: cci-default-state {
+				cci_i2c0_default: cci-i2c0-default-pins {
+					pins = "gpio19", "gpio20";
+					function = "cci_i2c0";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cci_i2c1_default: cci-i2c1-default-pins {
+					pins = "gpio21", "gpio22";
+					function = "cci_i2c1";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			cci_sleep: cci-sleep-state {
+				cci_i2c0_sleep: cci-i2c0-sleep-pins {
+					pins = "gpio19", "gpio20";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cci_i2c1_sleep: cci-i2c1-sleep-pins {
+					pins = "gpio21", "gpio22";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			spi8_default: spi8_default-state {
+				mosi-pins {
+					pins = "gpio45";
+					function = "blsp_spi8";
+				};
+				miso-pins {
+					pins = "gpio46";
+					function = "blsp_spi8";
+				};
+				cs-pins {
+					pins = "gpio47";
+					function = "blsp_spi8";
+				};
+				clk-pins {
+					pins = "gpio48";
+					function = "blsp_spi8";
+				};
+			};
+		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfd8c0000 0x6000>;
+			clocks = <&xo_board>,
+				 <&gcc GCC_MMSS_GPLL0_CLK_SRC>,
+				 <&gcc GPLL0_VOTE>,
+				 <&gcc GPLL1_VOTE>,
+				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi1_phy 1>,
+				 <&mdss_dsi1_phy 0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "mmss_gpll0_vote",
+				      "gpll0_vote",
+				      "gpll1_vote",
+				      "gfx3d_clk_src",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "hdmipll",
+				      "edp_link_clk",
+				      "edp_vco_div";
+		};
+
+		mdss: display-subsystem@fd900000 {
+			compatible = "qcom,mdss";
+			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&mmcc MDSS_GDSC>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			clock-names = "iface", "bus", "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			mdp: display-controller@fd900000 {
+				compatible = "qcom,msm8974-mdp5", "qcom,mdp5";
+				reg = <0xfd900100 0x22000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_VSYNC_CLK>;
+				clock-names = "iface", "bus", "core", "vsync";
+
+				interconnects = <&mmssnoc MNOC_MAS_MDP_PORT0 &bimc BIMC_SLV_EBI_CH0>;
+				interconnect-names = "mdp0-mem";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdp5_intf2_out: endpoint {
+							remote-endpoint = <&mdss_dsi1_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@fd922800 {
+				compatible = "qcom,msm8974-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922800 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>, <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE0_CLK>,
+					 <&mmcc MDSS_PCLK0_CLK>,
+					 <&mmcc MDSS_ESC0_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&mdss_dsi0_phy>;
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@fd922a00 {
+				compatible = "qcom,dsi-phy-28nm-hpm";
+				reg = <0xfd922a00 0xd4>,
+				      <0xfd922b00 0x280>,
+				      <0xfd922d80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			mdss_dsi1: dsi@fd922e00 {
+				compatible = "qcom,msm8974-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922e00 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE1_CLK_SRC>, <&mmcc PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE1_CLK>,
+					 <&mmcc MDSS_PCLK1_CLK>,
+					 <&mmcc MDSS_ESC1_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&mdss_dsi1_phy>;
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi1_in: endpoint {
+							remote-endpoint = <&mdp5_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi1_phy: phy@fd923000 {
+				compatible = "qcom,dsi-phy-28nm-hpm";
+				reg = <0xfd923000 0xd4>,
+				      <0xfd923100 0x280>,
+				      <0xfd923380 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+		};
+
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8974-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfda0c000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <100000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <100000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gpu: adreno@fdb00000 {
+			compatible = "qcom,adreno-330.1", "qcom,adreno";
+			reg = <0xfdb00000 0x10000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+
+			clocks = <&mmcc OXILI_GFX3D_CLK>,
+				 <&mmcc OXILICX_AHB_CLK>,
+				 <&mmcc OXILICX_AXI_CLK>;
+			clock-names = "core", "iface", "mem_iface";
+
+			sram = <&gmu_sram>;
+			power-domains = <&mmcc OXILICX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			interconnects = <&mmssnoc MNOC_MAS_GRAPHICS_3D &bimc BIMC_SLV_EBI_CH0>,
+					<&ocmemnoc OCMEM_VNOC_MAS_GFX3D &ocmemnoc OCMEM_SLV_OCMEM>;
+			interconnect-names = "gfx-mem", "ocmem";
+
+			// iommus = <&gpu_iommu 0>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-320000000 {
+					opp-hz = /bits/ 64 <320000000>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+				};
+
+				opp-27000000 {
+					opp-hz = /bits/ 64 <27000000>;
+				};
+			};
+		};
+
+		sram@fdd00000 {
+			compatible = "qcom,msm8974-ocmem";
+			reg = <0xfdd00000 0x2000>,
+			      <0xfec00000 0x180000>;
+			reg-names = "ctrl", "mem";
+			ranges = <0 0xfec00000 0x180000>;
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+				 <&mmcc OCMEMCX_OCMEMNOC_CLK>;
+			clock-names = "core", "iface";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gmu_sram: gmu-sram@0 {
+				reg = <0x0 0x100000>;
+			};
+		};
+
+		remoteproc_adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8974-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			clocks = <&xo_board>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 8>;
+				qcom,smd-edge = <1>;
+				label = "lpass";
+			};
+		};
+
+		imem: sram@fe805000 {
+			compatible = "qcom,msm8974-imem", "syscon", "simple-mfd";
+			reg = <0xfe805000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		q6-dsp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				q6_dsp_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		modemtx-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				modemtx_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		video-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				video_alert0: trip-point0 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		wlan-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				wlan_alert0: trip-point0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		gpu-top-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				gpu1_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		gpu-bottom-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				gpu2_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2 0xf08>,
+			     <GIC_PPI 3 0xf08>,
+			     <GIC_PPI 4 0xf08>,
+			     <GIC_PPI 1 0xf08>;
+		clock-frequency = <19200000>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
new file mode 100644
index 000000000000..fe227fd3f908
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
@@ -0,0 +1,492 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Fairphone 2";
+	compatible = "fairphone,fp2", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1;
+		mmc1 = &sdhc_2;
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_CAMERA>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&pm8941_l18>;
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@41 {
+		compatible = "ilitek,ili2120";
+		reg = <0x41>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&imem {
+	reboot-mode {
+		mode-normal = <0x77665501>;
+		mode-bootloader = <0x77665500>;
+		mode-recovery = <0x77665502>;
+	};
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio1", "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&pronto {
+	status = "okay";
+
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+	vddpx-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	iris {
+		vddxo-supply = <&pm8941_l6>;
+		vddrfa-supply = <&pm8941_l11>;
+		vddpa-supply = <&pm8941_l19>;
+		vdddig-supply = <&pm8941_s3>;
+	};
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	cx-supply = <&pm8841_s2>;
+};
+
+&remoteproc_mss {
+	status = "okay";
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	usb-charge-current-limit = <1500000>;
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,fast-charge-safe-voltage = <4380000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+	qcom,minimum-input-voltage = <4450000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	wcnss_pin_a: wcnss-pin-active-state {
+		wlan-pins {
+			pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+			function = "wlan";
+
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		bt-pins {
+			pins = "gpio35", "gpio43", "gpio44";
+			function = "bt";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		fm-pins {
+			pins = "gpio41", "gpio42";
+			function = "fm";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
new file mode 100644
index 000000000000..4c8edadea0ac
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
@@ -0,0 +1,543 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "OnePlus One";
+	compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+	qcom,msm-id = <194 0x10000>;
+	qcom,board-id = <8 0>;
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
+		pinctrl-names = "default";
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			debounce-interval = <150>;
+		};
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	fuel-gauge@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+		power-supplies = <&bq24196_charger>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	rmi4-i2c-dev@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		syna,startup-delay-ms = <100>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+			/*
+			 * Touchscreen size is 2040x1080, y-values between
+			 * 1920-2040 are used for touchkey (menu, home & back).
+			 * For now clip it off so we don't get touch events
+			 * outside of the display area.
+			 */
+			syna,clip-y-high = <1920>;
+		};
+	};
+
+	led-controller@36 {
+		compatible = "ti,lm3630a";
+		reg = <0x36>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 1>;
+			label = "lcd-backlight";
+			default-brightness = <80>;
+		};
+	};
+
+	led-controller@68 {
+		compatible = "si-en,sn3193";
+		reg = <0x68>;
+
+		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			label = "red:status";
+			led-max-microamp = <17500>;
+		};
+
+		led@2 {
+			reg = <2>;
+			label = "green:status";
+			led-max-microamp = <17500>;
+		};
+
+		led@3 {
+			reg = <3>;
+			label = "blue:status";
+			led-max-microamp = <17500>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	bq24196_charger: charger@6b {
+		compatible = "ti,bq24196";
+		reg = <0x6b>;
+		interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+		omit-battery-class;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&gcc {
+	compatible = "qcom,gcc-msm8974pro-ac";
+};
+
+&pm8941_coincell {
+	qcom,rset-ohms = <800>;
+	qcom,vset-millivolts = <3200>;
+
+	status = "okay";
+};
+
+&pm8941_gpios {
+	gpio_keys_default: gpio-keys-active-state {
+		pins = "gpio2", "gpio5";
+		function = "normal";
+		input-enable;
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_vib {
+	status = "okay";
+};
+
+&pronto {
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+	vddpx-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8941_l6>;
+		vddrfa-supply = <&pm8941_l11>;
+		vddpa-supply = <&pm8941_l19>;
+		vdddig-supply = <&pm8941_s3>;
+	};
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <875000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <154000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+
+	status = "okay";
+};
+
+&smbb {
+	status = "okay";
+};
+
+&tlmm {
+	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
+		pins = "gpio68";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	touch_default_state: touch-default-state {
+		int-pins {
+			pins = "gpio61";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		reset-pins {
+			pins = "gpio60";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	wcnss_pin_a: wcnss-pin-active-state {
+		wlan-pins {
+			pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+			function = "wlan";
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		bt-pins {
+			pins = "gpio35", "gpio43", "gpio44";
+			function = "bt";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&usb {
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
new file mode 100644
index 000000000000..b93539e2b87e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
@@ -0,0 +1,817 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "pma8084.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Samsung Galaxy S5";
+	compatible = "samsung,klte", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_3; /* SDC2 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-home {
+			label = "home_key";
+			gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_HOMEPAGE>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-gpio-touchkey {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_touchkey_pins>;
+
+		touchkey@20 {
+			compatible = "cypress,tm2-touchkey";
+			reg = <0x20>;
+
+			interrupt-parent = <&pma8084_gpios>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_pin>;
+
+			vcc-supply = <&max77826_ldo15>;
+			vdd-supply = <&pma8084_l19>;
+
+			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+		};
+	};
+
+	i2c-gpio-led {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_led_gpioex_pins>;
+
+		i2c-gpio,delay-us = <2>;
+
+		gpio_expander: gpio@20 {
+			compatible = "nxp,pcal6416";
+			reg = <0x20>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			vcc-supply = <&pma8084_s4>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpioex_pin>;
+
+			reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+		};
+
+		led-controller@30 {
+			compatible = "panasonic,an30259a";
+			reg = <0x30>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@2 {
+				reg = <2>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				reg = <3>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vreg_panel: panel-regulator {
+		compatible = "regulator-fixed";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_en_pin>;
+
+		regulator-name = "panel-vddr-reg";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+
+		gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupt-parent = <&pma8084_gpios>;
+		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+
+		vdd-supply = <&max77826_ldo13>;
+		vio-supply = <&pma8084_lvs2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
+
+		syna,startup-delay-ms = <100>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	pmic@60 {
+		reg = <0x60>;
+		compatible = "maxim,max77826";
+
+		regulators {
+			max77826_ldo1: LDO1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			max77826_ldo2: LDO2 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			max77826_ldo3: LDO3 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			max77826_ldo4: LDO4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo5: LDO5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo6: LDO6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo7: LDO7 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo8: LDO8 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo9: LDO9 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo10: LDO10 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2950000>;
+			};
+
+			max77826_ldo11: LDO11 {
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2950000>;
+			};
+
+			max77826_ldo12: LDO12 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo13: LDO13 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo14: LDO14 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo15: LDO15 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_buck: BUCK {
+				regulator-min-microvolt = <1225000>;
+				regulator-max-microvolt = <1225000>;
+			};
+
+			max77826_buckboost: BUCKBOOST {
+				regulator-min-microvolt = <3400000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+
+	fuelgauge@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x56>;
+
+		interrupt-parent = <&pma8084_gpios>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
+	};
+};
+
+&blsp2_uart2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart2_pins_active>;
+	pinctrl-1 = <&blsp2_uart2_pins_sleep>;
+
+	bluetooth {
+		compatible = "brcm,bcm43540-bt";
+		max-speed = <3000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pins>;
+		device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wakeup";
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+
+	vdda-supply = <&pma8084_l2>;
+	vdd-supply = <&pma8084_l22>;
+	vddio-supply = <&pma8084_l12>;
+
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "samsung,s6e3fa2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+
+		iovdd-supply = <&pma8084_lvs4>;
+		vddr-supply = <&vreg_panel>;
+
+		reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pma8084_l12>;
+};
+
+&pma8084_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	touchkey_pin: touchkey-int-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	touch_pin: touchscreen-int-state {
+		pins = "gpio8";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	panel_en_pin: panel-en-state {
+		pins = "gpio14";
+		function = "normal";
+		bias-pull-up;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	wlan_sleep_clk_pin: wlan-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
+
+		output-high;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+	};
+
+	panel_rst_pin: panel-rst-state {
+		pins = "gpio17";
+		function = "normal";
+		bias-disable;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio21";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	cx-supply = <&pma8084_s2>;
+};
+
+&remoteproc_mss {
+	status = "okay";
+	cx-supply = <&pma8084_s2>;
+	mss-supply = <&pma8084_s6>;
+	mx-supply = <&pma8084_s1>;
+	pll-supply = <&pma8084_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pma8084-regulators";
+
+		pma8084_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+
+		pma8084_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pma8084_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pma8084_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_s5: s5 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+
+		pma8084_s6: s6 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pma8084_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pma8084_l3: l3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pma8084_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pma8084_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pma8084_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pma8084_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pma8084_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pma8084_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pma8084_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pma8084_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pma8084_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pma8084_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pma8084_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pma8084_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pma8084_l25: l25 {
+			regulator-min-microvolt = <2100000>;
+			regulator-max-microvolt = <2100000>;
+		};
+
+		pma8084_l26: l26 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pma8084_l27: l27 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_lvs1: lvs1 {};
+		pma8084_lvs2: lvs2 {};
+		pma8084_lvs3: lvs3 {};
+		pma8084_lvs4: lvs4 {};
+
+		pma8084_5vs1: 5vs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pma8084_l20>;
+	vqmmc-supply = <&pma8084_s4>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pma8084_s4>;
+	non-removable;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
+	};
+};
+
+&sdhc_3 {
+	status = "okay";
+	max-frequency = <100000000>;
+	vmmc-supply = <&pma8084_l21>;
+	vqmmc-supply = <&pma8084_l13>;
+
+	/*
+	 * cd-gpio is intentionally disabled. If enabled, an SD card
+	 * present during boot is not initialized correctly. Without
+	 * cd-gpios the driver resorts to polling, so hotplug works.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>;
+	/* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */
+};
+
+&tlmm {
+	/* This seems suspicious, but somebody with this device should look into it. */
+	blsp2_uart2_pins_active: blsp2-uart2-pins-active-state {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "blsp_uart8";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	bt_pins: bt-pins-state {
+		hostwake-pins {
+			pins = "gpio75";
+			function = "gpio";
+			drive-strength = <16>;
+		};
+
+		devwake-pins {
+			pins = "gpio91";
+			function = "gpio";
+			drive-strength = <2>;
+		};
+	};
+
+	sdc1_on: sdhc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	sdc3_on: sdc3-on-state {
+		pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+		function = "sdc3";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	sdhc3_cd_pin: sdc3-cd-on-state {
+		pins = "gpio62";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc2_on: sdhc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	i2c_touchkey_pins: i2c-touchkey-state {
+		pins = "gpio95", "gpio96";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	i2c_led_gpioex_pins: i2c-led-gpioex-state {
+		pins = "gpio120", "gpio121";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	gpioex_pin: gpioex-state {
+		pins = "gpio145";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	wifi_pin: wifi-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	panel_te_pin: panel-state {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pma8084_l6>;
+	v3p3-supply = <&pma8084_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
new file mode 100644
index 000000000000..ee94741a26ed
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
@@ -0,0 +1,705 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Sony Xperia Z2 Tablet";
+	compatible = "sony,xperia-castor", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "tablet";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	vreg_bl_vddio: lcd-backlight-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bl_vddio";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		gpio = <&tlmm 69 0>;
+		enable-active-high;
+
+		vin-supply = <&pm8941_s3>;
+		startup-delay-us = <70000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_backlight_en_pin_a>;
+	};
+
+	vreg_vsp: lcd-dcdc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_vsp";
+		regulator-min-microvolt = <5600000>;
+		regulator-max-microvolt = <5600000>;
+
+		gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_pin>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <100>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+			touchscreen-inverted-x;
+		};
+	};
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	lp8566_wled: backlight@2c {
+		compatible = "ti,lp8556";
+		reg = <0x2c>;
+		power-supply = <&vreg_bl_vddio>;
+
+		bl-name = "backlight";
+		dev-ctrl = /bits/ 8 <0x05>;
+		init-brt = /bits/ 8 <0x3f>;
+
+		rom-a0h {
+			rom-addr = /bits/ 8 <0xa0>;
+			rom-val = /bits/ 8 <0xff>;
+		};
+		rom-a1h {
+			rom-addr = /bits/ 8 <0xa1>;
+			rom-val = /bits/ 8 <0x3f>;
+		};
+		rom-a2h {
+			rom-addr = /bits/ 8 <0xa2>;
+			rom-val = /bits/ 8 <0x20>;
+		};
+		rom-a3h {
+			rom-addr = /bits/ 8 <0xa3>;
+			rom-val = /bits/ 8 <0x5e>;
+		};
+		rom-a4h {
+			rom-addr = /bits/ 8 <0xa4>;
+			rom-val = /bits/ 8 <0x02>;
+		};
+		rom-a5h {
+			rom-addr = /bits/ 8 <0xa5>;
+			rom-val = /bits/ 8 <0x04>;
+		};
+		rom-a6h {
+			rom-addr = /bits/ 8 <0xa6>;
+			rom-val = /bits/ 8 <0x80>;
+		};
+		rom-a7h {
+			rom-addr = /bits/ 8 <0xa7>;
+			rom-val = /bits/ 8 <0xf7>;
+		};
+		rom-a9h {
+			rom-addr = /bits/ 8 <0xa9>;
+			rom-val = /bits/ 8 <0x80>;
+		};
+		rom-aah {
+			rom-addr = /bits/ 8 <0xaa>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+		rom-aeh {
+			rom-addr = /bits/ 8 <0xae>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_pin>, <&bt_dev_wake_pin>, <&bt_reg_on_pin>;
+
+		host-wakeup-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pm8941_coincell {
+	status = "okay";
+
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	bt_reg_on_pin: bt-reg-on-state {
+		pins = "gpio16";
+		function = "normal";
+
+		output-low;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio17";
+		function = "func2";
+
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio18";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	lcd_dcdc_en_pin_a: lcd-dcdc-en-active-state {
+		pins = "gpio20";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+		input-disable;
+		output-low;
+	};
+
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <154000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <500000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	non-removable;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc3_on>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bcrmf@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		brcm,drive-strength = <10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	usb-charge-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	lcd_backlight_en_pin_a: lcd-backlight-vddio-state {
+		pins = "gpio69";
+		function = "gpio";
+		drive-strength = <10>;
+		output-low;
+		bias-disable;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	sdc3_on: sdc3-on-state {
+		clk-pins {
+			pins = "gpio40";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio39";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio35", "gpio36", "gpio37", "gpio38";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	ts_int_pin: ts-int-pin-state {
+		pins = "gpio86";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bt_host_wake_pin: bt-host-wake-state {
+		pins = "gpio95";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	bt_dev_wake_pin: bt-dev-wake-state {
+		pins = "gpio96";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974pro.dtsi
new file mode 100644
index 000000000000..58df6e75ab6d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+
+&gcc {
+	compatible = "qcom,gcc-msm8974pro";
+};
+
+&gpu {
+	compatible = "qcom,adreno-330.2", "qcom,adreno";
+};
+
+&sdhc_1 {
+	clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+		 <&gcc GCC_SDCC1_APPS_CLK>,
+		 <&xo_board>,
+		 <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
+		 <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
+	clock-names = "iface", "core", "xo", "cal", "sleep";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
new file mode 100644
index 000000000000..247069361909
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "qcom-sdx55.dtsi"
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <arm64/qcom/pm8150b.dtsi>
+#include "pmx55.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDX55 MTP";
+	compatible = "qcom,sdx55-mtp", "qcom,sdx55";
+	qcom,board-id = <0x5010008 0x0>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_debug_mem: memory@8ef00000 {
+			no-map;
+			reg = <0x8ef00000 0x800000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90c00000 {
+			no-map;
+			reg = <0x90c00000 0xd400000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx55-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s7e_mx_0p752: pmx55-s7e {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s7e_mx_0p752";
+		regulator-min-microvolt = <752000>;
+		regulator-max-microvolt = <752000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx55-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-l1-l2-supply = <&vreg_s2e_1p224>;
+		vdd-l3-l9-supply = <&vreg_s3e_0p824>;
+		vdd-l4-l12-supply = <&vreg_s4e_1p904>;
+		vdd-l5-l6-supply = <&vreg_s4e_1p904>;
+		vdd-l7-l8-supply = <&vreg_s3e_0p824>;
+		vdd-l10-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l14-supply = <&vreg_s7e_mx_0p752>;
+		vdd-l15-supply = <&vreg_s2e_1p224>;
+		vdd-l16-supply = <&vreg_s4e_1p904>;
+
+		vreg_s2e_1p224: smps2 {
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3e_0p824: smps3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s4e_1p904: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1960000>;
+		};
+
+		vreg_l1e_bb_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4e_bb_0p875: ldo4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <872000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5e_bb_1p7: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10e_3p1: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+	vdda33-supply = <&vreg_l10e_3p1>;
+	vdda18-supply = <&vreg_l5e_bb_1p7>;
+};
+
+&usb_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l4e_bb_0p875>;
+	vdda-pll-supply = <&vreg_l1e_bb_1p2>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
new file mode 100644
index 000000000000..082f7ed1a01f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcom-sdx55.dtsi"
+#include "pmx55.dtsi"
+
+/ {
+	model = "Thundercomm T55 Development Kit";
+	compatible = "qcom,sdx55-t55", "qcom,sdx55";
+	qcom,board-id = <0xb010008 0x4>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_debug_mem: memory@8ef00000 {
+			no-map;
+			reg = <0x8ef00000 0x800000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0xf800000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx55-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s7e_mx_0p752: pmx55-s7e {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s7e_mx_0p752";
+		regulator-min-microvolt = <752000>;
+		regulator-max-microvolt = <752000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_sd_vdd: sd-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_sd_vdd";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		vin-supply = <&vreg_vddpx_2>;
+	};
+
+	vreg_vddpx_2: vddpx-2 {
+		compatible = "regulator-gpio";
+		regulator-name = "vreg_vddpx_2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2850000>;
+		enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+		gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0>, <2850000 1>;
+		startup-delay-us = <200000>;
+		enable-active-high;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx55-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-l1-l2-supply = <&vreg_s2e_1p224>;
+		vdd-l3-l9-supply = <&vreg_s3e_0p824>;
+		vdd-l4-l12-supply = <&vreg_s4e_1p904>;
+		vdd-l5-l6-supply = <&vreg_s4e_1p904>;
+		vdd-l7-l8-supply = <&vreg_s3e_0p824>;
+		vdd-l10-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l14-supply = <&vreg_s7e_mx_0p752>;
+		vdd-l15-supply = <&vreg_s2e_1p224>;
+		vdd-l16-supply = <&vreg_s4e_1p904>;
+
+		vreg_s2e_1p224: smps2 {
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3e_0p824: smps3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s4e_1p904: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1960000>;
+		};
+
+		vreg_l1e_bb_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4e_bb_0p875: ldo4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <872000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5e_bb_1p7: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10e_3p1: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&ipa_fw_mem>;
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l1e_bb_1p2>;
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+
+	status = "okay";
+};
+
+&pcie_rc {
+	perst-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-0 = <&pcie_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* efs2 partition is secured */
+		secure-regions = /bits/ 64 <0x500000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
+};
+
+&tlmm {
+	pcie_default: pcie-default-state {
+		clkreq-pins {
+			pins = "gpio56";
+			function = "pcie_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio57";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+		       pins = "gpio53";
+		       function = "gpio";
+		       drive-strength = <2>;
+		       bias-pull-up;
+	       };
+	};
+};
+
+&usb_hsphy {
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+	vdda33-supply = <&vreg_l10e_3p1>;
+	vdda18-supply = <&vreg_l5e_bb_1p7>;
+
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l4e_bb_0p875>;
+	vdda-pll-supply = <&vreg_l1e_bb_1p2>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
new file mode 100644
index 000000000000..e336a15b45c4
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcom-sdx55.dtsi"
+#include "pmx55.dtsi"
+
+/ {
+	model = "Telit FN980 TLB";
+	compatible = "qcom,sdx55-telit-fn980-tlb", "qcom,sdx55";
+	qcom,board-id = <0xb010008 0x0>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_debug_mem: memory@8ef00000 {
+			no-map;
+			reg = <0x8ef00000 0x800000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0xf800000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx55-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s7e_mx_0p752: pmx55-s7e {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s7e_mx_0p752";
+		regulator-min-microvolt = <752000>;
+		regulator-max-microvolt = <752000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_sd_vdd: sd-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_sd_vdd";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		vin-supply = <&vreg_vddpx_2>;
+	};
+
+	vreg_vddpx_2: vddpx-2 {
+		compatible = "regulator-gpio";
+		regulator-name = "vreg_vddpx_2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2850000>;
+		enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+		gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0>, <2850000 1>;
+		startup-delay-us = <200000>;
+		enable-active-high;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx55-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-l1-l2-supply = <&vreg_s2e_1p224>;
+		vdd-l3-l9-supply = <&vreg_s3e_0p824>;
+		vdd-l4-l12-supply = <&vreg_s4e_1p904>;
+		vdd-l5-l6-supply = <&vreg_s4e_1p904>;
+		vdd-l7-l8-supply = <&vreg_s3e_0p824>;
+		vdd-l10-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l14-supply = <&vreg_s7e_mx_0p752>;
+		vdd-l15-supply = <&vreg_s2e_1p224>;
+		vdd-l16-supply = <&vreg_s4e_1p904>;
+
+		vreg_s2e_1p224: smps2 {
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3e_0p824: smps3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s4e_1p904: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1960000>;
+		};
+
+		vreg_l1e_bb_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4e_bb_0p875: ldo4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <872000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5e_bb_1p7: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10e_3p1: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&ipa_fw_mem>;
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l1e_bb_1p2>;
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+
+	status = "okay";
+};
+
+&pcie_ep {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_ep_clkreq_default &pcie_ep_perst_default
+		     &pcie_ep_wake_default>;
+
+	reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* ico and efs2 partitions are secured */
+		secure-regions = /bits/ 64 <0x500000 0x500000
+					    0xa00000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
+};
+
+&tlmm {
+	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
+		pins = "gpio56";
+		function = "pcie_clkreq";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie_ep_perst_default: pcie-ep-perst-default-state {
+		pins = "gpio57";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	pcie_ep_wake_default: pcie-ep-wake-default-state {
+		pins = "gpio53";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb_hsphy {
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+	vdda33-supply = <&vreg_l10e_3p1>;
+	vdda18-supply = <&vreg_l5e_bb_1p7>;
+
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l4e_bb_0p875>;
+	vdda-pll-supply = <&vreg_l1e_bb_1p2>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom/qcom-sdx55.dtsi
new file mode 100644
index 000000000000..2045fc779f88
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55.dtsi
@@ -0,0 +1,868 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SDX55 SoC device tree source
+ *
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020, Linaro Ltd.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdx55.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,sdx55.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	qcom,msm-id = <357 0x10000>, <368 0x10000>, <418 0x10000>;
+	interrupt-parent = <&intc>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <38400000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+
+		nand_clk_dummy: nand-clk-dummy {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			power-domains = <&rpmhpd SDX55_CX>;
+			power-domain-names = "rpmhpd";
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdx55", "qcom,scm";
+		};
+	};
+
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-345600000 {
+			opp-hz = /bits/ 64 <345600000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+			required-opps = <&rpmhpd_opp_turbo>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		hyp_mem: memory@8fc00000 {
+			no-map;
+			reg = <0x8fc00000 0x80000>;
+		};
+
+		ac_db_mem: memory@8fc80000 {
+			no-map;
+			reg = <0x8fc80000 0x40000>;
+		};
+
+		secdata_mem: memory@8fcfd000 {
+			no-map;
+			reg = <0x8fcfd000 0x1000>;
+		};
+
+		sbl_mem: memory@8fd00000 {
+			no-map;
+			reg = <0x8fd00000 0x100000>;
+		};
+
+		aop_image: memory@8fe00000 {
+			no-map;
+			reg = <0x8fe00000 0x20000>;
+		};
+
+		aop_cmd_db: memory@8fe20000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x8fe20000 0x20000>;
+			no-map;
+		};
+
+		smem_mem: memory@8fe40000 {
+			no-map;
+			reg = <0x8fe40000 0xc0000>;
+		};
+
+		tz_mem: memory@8ff00000 {
+			no-map;
+			reg = <0x8ff00000 0x100000>;
+		};
+
+		tz_apps_mem: memory@90000000 {
+			no-map;
+			reg = <0x90000000 0x500000>;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-mpss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&apcs 14>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sdx55";
+			reg = <0x100000 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo", "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+		};
+
+		blsp1_uart3: serial@831000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x00831000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc 30>,
+				 <&gcc 9>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		usb_hsphy: phy@ff4000 {
+			compatible = "qcom,sdx55-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0x00ff4000 0x114>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_BCR>;
+		};
+
+		usb_qmpphy: phy@ff6000 {
+			compatible = "qcom,sdx55-qmp-usb3-uni-phy";
+			reg = <0x00ff6000 0x1000>;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "cfg_ahb",
+				      "pipe";
+			clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+
+			resets = <&gcc GCC_USB3_PHY_BCR>,
+				 <&gcc GCC_USB3PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "phy_phy";
+
+			status = "disabled";
+		};
+
+		mc_virt: interconnect@1100000 {
+			compatible = "qcom,sdx55-mc-virt";
+			reg = <0x01100000 0x400000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		mem_noc: interconnect@9680000 {
+			compatible = "qcom,sdx55-mem-noc";
+			reg = <0x09680000 0x40000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@162c000 {
+			compatible = "qcom,sdx55-system-noc";
+			reg = <0x0162c000 0x31200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		qpic_bam: dma-controller@1b04000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x01b04000 0x1c000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,controlled-remotely;
+			status = "disabled";
+		};
+
+		qpic_nand: nand-controller@1b30000 {
+			compatible = "qcom,sdx55-nand";
+			reg = <0x01b30000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>,
+				 <&nand_clk_dummy>;
+			clock-names = "core", "aon";
+
+			dmas = <&qpic_bam 0>,
+			       <&qpic_bam 1>,
+			       <&qpic_bam 2>;
+			dma-names = "tx", "rx", "cmd";
+			status = "disabled";
+		};
+
+		pcie_rc: pcie@1c00000 {
+			compatible = "qcom,pcie-sdx55";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xc8>,
+			      <0x40001000 0x1000>,
+			      <0x40100000 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x40300000 0x0 0x3fd00000>;
+
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7",
+					  "msi8";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 141 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 144 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_PIPE_CLK>,
+				 <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "sleep";
+
+			assigned-clocks = <&gcc GCC_PCIE_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommu-map = <0x0   &apps_smmu 0x0200 0x1>,
+				    <0x100 &apps_smmu 0x0201 0x1>,
+				    <0x200 &apps_smmu 0x0202 0x1>,
+				    <0x300 &apps_smmu 0x0203 0x1>,
+				    <0x400 &apps_smmu 0x0204 0x1>;
+
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_GDSC>;
+
+			phys = <&pcie_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie_ep: pcie-ep@1c00000 {
+			compatible = "qcom,sdx55-pcie-ep";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xc8>,
+			      <0x40001000 0x1000>,
+			      <0x40200000 0x100000>,
+			      <0x01c03000 0x3000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "addr_space",
+				    "mmio";
+
+			qcom,perst-regs = <&tcsr 0xb258 0xb270>;
+
+			clocks = <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "sleep",
+				      "ref";
+
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global",
+					  "doorbell";
+
+			interconnects = <&system_noc MASTER_PCIE &mc_virt SLAVE_EBI_CH0>;
+			interconnect-names = "pcie-mem";
+
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "core";
+			power-domains = <&gcc PCIE_GDSC>;
+			phys = <&pcie_phy>;
+			phy-names = "pciephy";
+			max-link-speed = <3>;
+			num-lanes = <2>;
+
+			status = "disabled";
+		};
+
+		pcie_phy: phy@1c06000 {
+			compatible = "qcom,sdx55-qmp-pcie-phy";
+			reg = <0x01c06000 0x2000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
+				 <&gcc GCC_PCIE_RCHNG_PHY_CLK>,
+				 <&gcc GCC_PCIE_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "refgen",
+				      "pipe";
+
+			clock-output-names = "pcie_pipe_clk";
+			#clock-cells = <0>;
+
+			#phy-cells = <0>;
+
+			resets = <&gcc GCC_PCIE_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+		};
+
+		ipa: ipa@1e40000 {
+			compatible = "qcom,sdx55-ipa";
+
+			iommus = <&apps_smmu 0x5e0 0x0>,
+				 <&apps_smmu 0x5e2 0x0>;
+			reg = <0x1e40000 0x7000>,
+			      <0x1e50000 0x4b20>,
+			      <0x1e04000 0x2c000>;
+			reg-names = "ipa-reg",
+				    "ipa-shared",
+				    "gsi";
+
+			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
+					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ipa",
+					  "gsi",
+					  "ipa-clock-query",
+					  "ipa-setup-ready";
+
+			clocks = <&rpmhcc RPMH_IPA_CLK>;
+			clock-names = "core";
+
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI_CH0>,
+					<&system_noc MASTER_IPA &system_noc SLAVE_OCIMEM>,
+					<&mem_noc MASTER_AMPSS_M0 &system_noc SLAVE_IPA_CFG>;
+			interconnect-names = "memory",
+					     "imem",
+					     "config";
+
+			qcom,smem-states = <&ipa_smp2p_out 0>,
+					   <&ipa_smp2p_out 1>;
+			qcom,smem-state-names = "ipa-clock-enabled-valid",
+						"ipa-clock-enabled";
+
+			status = "disabled";
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1fc0000 {
+			compatible = "qcom,sdx55-tcsr", "syscon";
+			reg = <0x01fc0000 0x1000>;
+		};
+
+		sdhc_1: mmc@8804000 {
+			compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x08804000 0x1000>;
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>;
+			clock-names = "iface", "core";
+			status = "disabled";
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sdx55-mpss-pas";
+			reg = <0x04080000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SDX55_CX>,
+					<&rpmhpd SDX55_MSS>;
+			power-domain-names = "cx", "mss";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>;
+				label = "mpss";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs 15>;
+			};
+		};
+
+		usb: usb@a6f8800 {
+			compatible = "qcom,sdx55-dwc3", "qcom,dwc3";
+			reg = <0x0a6f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB30_SLV_AHB_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_USB30_MSTR_AXI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 51 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 11 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 10 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_GDSC>;
+
+			resets = <&gcc GCC_USB30_BCR>;
+
+			usb_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a600000 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_hsphy>, <&usb_qmpphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		pdc: interrupt-controller@b210000 {
+			compatible = "qcom,sdx55-pdc", "qcom,pdc";
+			reg = <0x0b210000 0x30000>;
+			qcom,pdc-ranges = <0 179 52>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		restart@c264000 {
+			compatible = "qcom,pshold";
+			reg = <0x0c264000 0x1000>;
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0c440000 0x0000d00>,
+			      <0x0c600000 0x2000000>,
+			      <0x0e600000 0x0100000>,
+			      <0x0e700000 0x00a0000>,
+			      <0x0c40a000 0x0000700>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sdx55-pinctrl";
+			reg = <0xf100000 0x300000>;
+			interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 108>;
+		};
+
+		sram@1468f000 {
+			compatible = "qcom,sdx55-imem", "syscon", "simple-mfd";
+			reg = <0x1468f000 0x1000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0x0 0x1468f000 0x1000>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0x200>;
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sdx55-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+			reg = <0x15000000 0x20000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17800000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <3>;
+			reg = <0x17800000 0x1000>,
+			      <0x17802000 0x1000>;
+		};
+
+		a7pll: clock@17808000 {
+			compatible = "qcom,sdx55-a7pll";
+			reg = <0x17808000 0x1000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <0>;
+		};
+
+		apcs: mailbox@17810000 {
+			compatible = "qcom,sdx55-apcs-gcc", "syscon";
+			reg = <0x17810000 0x2000>;
+			#mbox-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>;
+			clock-names = "ref", "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		watchdog@17817000 {
+			compatible = "qcom,apss-wdt-sdx55", "qcom,kpss-wdt";
+			reg = <0x17817000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@17820000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x17820000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17821000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 7 0x4>,
+					     <GIC_SPI 6 0x4>;
+				reg = <0x17821000 0x1000>,
+				      <0x17822000 0x1000>;
+			};
+
+			frame@17823000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 8 0x4>;
+				reg = <0x17823000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17824000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 9 0x4>;
+				reg = <0x17824000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17825000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 10 0x4>;
+				reg = <0x17825000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17826000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 11 0x4>;
+				reg = <0x17826000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17827000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 12 0x4>;
+				reg = <0x17827000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17828000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 13 0x4>;
+				reg = <0x17828000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17829000 {
+				frame-number = <7>;
+				interrupts = <GIC_SPI 14 0x4>;
+				reg = <0x17829000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17830000 {
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x17830000 0x10000>, <0x17840000 0x10000>;
+			reg-names = "drv-0", "drv-1";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <1>;
+			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   2>,
+					  <WAKE_TCS    2>, <CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sdx55-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdx55-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
new file mode 100644
index 000000000000..07c10c84eefa
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
@@ -0,0 +1,342 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+/* PM7250B is configured to use SID2/3 */
+#define PM7250B_SID 2
+#define PM7250B_SID1 3
+
+#include "qcom-sdx65.dtsi"
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <arm64/qcom/pmk8350.dtsi>
+#include <arm64/qcom/pm7250b.dtsi>
+#include "pmx65.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDX65 MTP";
+	compatible = "qcom,sdx65-mtp", "qcom,sdx65";
+	qcom,board-id = <0x2010008 0x302>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_dsm: memory@8c400000 {
+			no-map;
+			reg = <0x8c400000 0x3200000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0x10000000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx65_bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx65-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-l1-supply = <&vreg_s2b_1p224>;
+		vdd-l2-l18-supply = <&vreg_s2b_1p224>;
+		vdd-l3-supply = <&vreg_s8b_0p824>;
+		vdd-l4-supply = <&vreg_s7b_0p936>;
+		vdd-l5-l6-l16-supply = <&vreg_s4b_1p824>;
+		vdd-l7-supply = <&vreg_s3b_0p776>;
+		vdd-l8-l9-supply = <&vreg_s8b_0p824>;
+		vdd-l10-supply = <&vreg_bob_3p3>;
+		vdd-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l12-supply = <&vreg_s2b_1p224>;
+		vdd-l14-supply = <&vreg_s3b_0p776>;
+		vdd-l15-supply = <&vreg_s2b_1p224>;
+		vdd-l17-supply = <&vreg_s8b_0p824>;
+		vdd-l19-supply = <&vreg_s3b_0p776>;
+		vdd-l20-supply = <&vreg_s7b_0p936>;
+		vdd-l21-supply = <&vreg_s7b_0p936>;
+
+		vreg_s2b_1p224: smps2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3b_0p776: smps3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_s4b_1p824: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		vreg_s7b_0p936: smps7 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_s8b_0p824: smps8 {
+			regulator-min-microvolt = <304000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		vreg_l1b_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_0p88: ldo4 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_1p8: ldo5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_3p08: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo17 {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo19 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo20 {
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo21 {
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&ipa {
+	qcom,gsi-loader = "skip";
+	status = "okay";
+};
+
+&pcie_ep {
+	pinctrl-0 = <&pcie_ep_clkreq_default
+		     &pcie_ep_perst_default
+		     &pcie_ep_wake_default>;
+	pinctrl-names = "default";
+
+	reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l1b_1p2>;
+	vdda-pll-supply = <&vreg_l4b_0p88>;
+
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* ico and efs2 partitions are secured */
+		secure-regions = /bits/ 64 <0x500000 0x500000
+					    0xa00000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
+};
+
+&tlmm {
+	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
+		pins = "gpio56";
+		function = "pcie_clkreq";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie_ep_perst_default: pcie-ep-perst-default-state {
+		pins = "gpio57";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	pcie_ep_wake_default: pcie-ep-wake-default-state {
+		pins = "gpio53";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_hsphy {
+	vdda-pll-supply = <&vreg_l4b_0p88>;
+	vdda33-supply = <&vreg_l10b_3p08>;
+	vdda18-supply = <&vreg_l5b_1p8>;
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l4b_0p88>;
+	vdda-pll-supply = <&vreg_l1b_1p2>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
new file mode 100644
index 000000000000..40591a4da6a4
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
@@ -0,0 +1,813 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SDX65 SoC device tree source
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ *
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdx65.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/interconnect/qcom,sdx65.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	qcom,msm-id = <458 0x10000>, <483 0x10000>, <509 0x10000>;
+	interrupt-parent = <&intc>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			clock-output-names = "sleep_clk";
+			#clock-cells = <0>;
+		};
+
+		nand_clk_dummy: nand-clk-dummy {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			power-domains = <&rpmhpd SDX65_CX_AO>;
+			power-domain-names = "rpmhpd";
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdx65", "qcom,scm";
+		};
+	};
+
+	mc_virt: interconnect-mc-virt {
+		compatible = "qcom,sdx65-mc-virt";
+		#interconnect-cells = <1>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-345600000 {
+			opp-hz = /bits/ 64 <345600000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			required-opps = <&rpmhpd_opp_turbo>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		tz_heap_mem: memory@8fcad000 {
+			no-map;
+			reg = <0x8fcad000 0x40000>;
+		};
+
+		secdata_mem: memory@8fcfd000 {
+			no-map;
+			reg = <0x8fcfd000 0x1000>;
+		};
+
+		hyp_mem: memory@8fd00000 {
+			no-map;
+			reg = <0x8fd00000 0x80000>;
+		};
+
+		access_control_mem: memory@8fd80000 {
+			no-map;
+			reg = <0x8fd80000 0x80000>;
+		};
+
+		aop_mem: memory@8fe00000 {
+			no-map;
+			reg = <0x8fe00000 0x20000>;
+		};
+
+		smem_mem: memory@8fe20000 {
+			compatible = "qcom,smem";
+			reg = <0x8fe20000 0xc0000>;
+			hwlocks = <&tcsr_mutex 3>;
+			no-map;
+		};
+
+		cmd_db: reserved-memory@8fee0000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x8fee0000 0x20000>;
+			no-map;
+		};
+
+		tz_mem: memory@8ff00000 {
+			no-map;
+			reg = <0x8ff00000 0x100000>;
+		};
+
+		tz_apps_mem: memory@90000000 {
+			no-map;
+			reg = <0x90000000 0x500000>;
+		};
+
+		llcc_tcm_mem: memory@15800000 {
+			no-map;
+			reg = <0x15800000 0x800000>;
+		};
+	};
+
+	smp2p-mpss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&apcs 14>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sdx65";
+			reg = <0x00100000 0x001f7400>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK_A>,
+				 <&sleep_clk>,
+				 <&pcie_phy>,
+				 <0>;
+			clock-names = "bi_tcxo",
+				      "bi_tcxo_ao",
+				      "sleep_clk",
+				      "pcie_pipe_clk",
+				      "usb3_phy_wrapper_gcc_usb30_pipe_clk";
+			#power-domain-cells = <1>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		blsp1_uart3: serial@831000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x00831000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		usb_hsphy: phy@ff4000 {
+			compatible = "qcom,sdx65-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0xff4000 0x120>;
+			#phy-cells = <0>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_BCR>;
+			status = "disabled";
+		};
+
+		usb_qmpphy: phy@ff6000 {
+			compatible = "qcom,sdx65-qmp-usb3-uni-phy";
+			reg = <0x00ff6000 0x2000>;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_EN>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "cfg_ahb",
+				      "pipe";
+			clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+
+			resets = <&gcc GCC_USB3_PHY_BCR>,
+				 <&gcc GCC_USB3PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "phy_phy";
+
+			status = "disabled";
+
+		};
+
+		system_noc: interconnect@1620000 {
+			compatible = "qcom,sdx65-system-noc";
+			reg = <0x01620000 0x31200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		qpic_bam: dma-controller@1b04000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x01b04000 0x1c000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,controlled-remotely;
+			status = "disabled";
+		};
+
+		qpic_nand: nand-controller@1b30000 {
+			compatible = "qcom,sdx55-nand";
+			reg = <0x01b30000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>,
+				 <&nand_clk_dummy>;
+			clock-names = "core", "aon";
+
+			dmas = <&qpic_bam 0>,
+			       <&qpic_bam 1>,
+			       <&qpic_bam 2>;
+			dma-names = "tx", "rx", "cmd";
+			status = "disabled";
+		};
+
+		pcie_ep: pcie-ep@1c00000 {
+			compatible = "qcom,sdx65-pcie-ep", "qcom,sdx55-pcie-ep";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xa8>,
+			      <0x40001000 0x1000>,
+			      <0x40200000 0x100000>,
+			      <0x01c03000 0x3000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "addr_space",
+				    "mmio";
+
+			qcom,perst-regs = <&tcsr 0xb258 0xb270>;
+
+			clocks = <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_EN>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "sleep",
+				      "ref";
+
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global", "doorbell";
+
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "core";
+
+			power-domains = <&gcc PCIE_GDSC>;
+
+			phys = <&pcie_phy>;
+			phy-names = "pciephy";
+
+			max-link-speed = <3>;
+			num-lanes = <2>;
+
+			status = "disabled";
+		};
+
+		pcie_phy: phy@1c06000 {
+			compatible = "qcom,sdx65-qmp-gen4x2-pcie-phy";
+			reg = <0x01c06000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_RCHNG_PHY_CLK>,
+				 <&gcc GCC_PCIE_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1fcb000 {
+			compatible = "qcom,sdx65-tcsr", "syscon";
+			reg = <0x01fc0000 0x1000>;
+		};
+
+		ipa: ipa@3f40000 {
+			compatible = "qcom,sdx65-ipa";
+
+			reg = <0x03f40000 0x10000>,
+			      <0x03f50000 0x5000>,
+			      <0x03e04000 0xfc000>;
+			reg-names = "ipa-reg",
+				    "ipa-shared",
+				    "gsi";
+
+			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
+					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ipa",
+					  "gsi",
+					  "ipa-clock-query",
+					  "ipa-setup-ready";
+
+			iommus = <&apps_smmu 0x5e0 0x0>,
+				 <&apps_smmu 0x5e2 0x0>;
+
+			clocks = <&rpmhcc RPMH_IPA_CLK>;
+			clock-names = "core";
+
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI1>,
+					<&mem_noc MASTER_APPSS_PROC &system_noc SLAVE_IPA_CFG>;
+			interconnect-names = "memory",
+					     "config";
+
+			qcom,smem-states = <&ipa_smp2p_out 0>,
+					   <&ipa_smp2p_out 1>;
+			qcom,smem-state-names = "ipa-clock-enabled-valid",
+						"ipa-clock-enabled";
+
+			status = "disabled";
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sdx55-mpss-pas";
+			reg = <0x04080000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SDX65_CX>,
+					<&rpmhpd SDX65_MSS>;
+			power-domain-names = "cx", "mss";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>;
+				label = "mpss";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs 15>;
+			};
+		};
+
+		sdhc_1: mmc@8804000 {
+			compatible = "qcom,sdx65-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x08804000 0x1000>;
+			reg-names = "hc";
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>;
+			clock-names = "iface", "core";
+			status = "disabled";
+		};
+
+		mem_noc: interconnect@9680000 {
+			compatible = "qcom,sdx65-mem-noc";
+			reg = <0x09680000 0x27200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		usb: usb@a6f8800 {
+			compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
+			reg = <0x0a6f8800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB30_SLV_AHB_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_USB30_MSTR_AXI_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+					"sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 76 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 18 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 19 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_GDSC>;
+
+			resets = <&gcc GCC_USB30_BCR>;
+
+			status = "disabled";
+
+			usb_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a600000 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_hsphy>, <&usb_qmpphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		restart@c264000 {
+			compatible = "qcom,pshold";
+			reg = <0x0c264000 0x1000>;
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0xc440000 0xd00>,
+				<0xc600000 0x2000000>,
+				<0xe600000 0x100000>,
+				<0xe700000 0xa0000>,
+				<0xc40a000 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "periph_irq";
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			qcom,channel = <0>;
+			qcom,ee = <0>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sdx65-tlmm";
+			reg = <0xf100000 0x300000>;
+			interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 109>;
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <2>;
+		};
+
+		pdc: interrupt-controller@b210000 {
+			compatible = "qcom,sdx65-pdc", "qcom,pdc";
+			reg = <0xb210000 0x10000>;
+			qcom,pdc-ranges = <0 147 52>, <52 266 32>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		sram@1468f000 {
+			compatible = "qcom,sdx65-imem", "syscon", "simple-mfd";
+			reg = <0x1468f000 0x1000>;
+			ranges = <0x0 0x1468f000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0xc8>;
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sdx65-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+			reg = <0x15000000 0x40000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts =	<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17800000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <3>;
+			reg = <0x17800000 0x1000>,
+			      <0x17802000 0x1000>;
+		};
+
+		a7pll: clock@17808000 {
+			compatible = "qcom,sdx55-a7pll";
+			reg = <0x17808000 0x1000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <0>;
+		};
+
+		apcs: mailbox@17810000 {
+			compatible = "qcom,sdx55-apcs-gcc", "syscon";
+			reg = <0x17810000 0x2000>;
+			#mbox-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>;
+			clock-names = "ref", "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		watchdog@17817000 {
+			compatible = "qcom,apss-wdt-sdx65", "qcom,kpss-wdt";
+			reg = <0x17817000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@17820000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x17820000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17821000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 7 0x4>,
+					     <GIC_SPI 6 0x4>;
+				reg = <0x17821000 0x1000>,
+				      <0x17822000 0x1000>;
+			};
+
+			frame@17823000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 8 0x4>;
+				reg = <0x17823000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17824000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 9 0x4>;
+				reg = <0x17824000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17825000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 10 0x4>;
+				reg = <0x17825000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17826000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 11 0x4>;
+				reg = <0x17826000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17827000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 12 0x4>;
+				reg = <0x17827000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17828000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 13 0x4>;
+				reg = <0x17828000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17829000 {
+				frame-number = <7>;
+				interrupts = <GIC_SPI 14 0x4>;
+				reg = <0x17829000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17830000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x17830000 0x10000>,
+			    <0x17840000 0x10000>;
+			reg-names = "drv-0", "drv-1";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				   <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <1>;
+			qcom,tcs-config = <ACTIVE_TCS  2>,
+				<SLEEP_TCS   2>,
+				<WAKE_TCS    2>,
+				<CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sdx65-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdx65-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <1 13 0xf08>,
+			<1 12 0xf08>,
+			<1 10 0xf08>,
+			<1 11 0xf08>;
+		clock-frequency = <19200000>;
+	};
+};
diff --git a/arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi b/arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi
deleted file mode 100644
index 79fce67ebb1c..000000000000
--- a/arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi
+++ /dev/null
@@ -1,39 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Common file for the AA104XD12 panel connected to Renesas R-Car boards
- *
- * Copyright (C) 2014 Renesas Electronics Corp.
- */
-
-/ {
-	panel {
-		compatible = "mitsubishi,aa104xd12", "panel-lvds";
-
-		width-mm = <210>;
-		height-mm = <158>;
-		data-mapping = "jeida-18";
-
-		panel-timing {
-			/* 1024x768 @65Hz */
-			clock-frequency = <65000000>;
-			hactive = <1024>;
-			vactive = <768>;
-			hsync-len = <136>;
-			hfront-porch = <20>;
-			hback-porch = <160>;
-			vfront-porch = <3>;
-			vback-porch = <29>;
-			vsync-len = <6>;
-		};
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds_connector>;
-			};
-		};
-	};
-};
-
-&lvds_connector {
-	remote-endpoint = <&panel_in>;
-};
diff --git a/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts b/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts
deleted file mode 100644
index 4e57ae2688fc..000000000000
--- a/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts
+++ /dev/null
@@ -1,28 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the RZN1D-DB Board
- *
- * Copyright (C) 2018 Renesas Electronics Europe Limited
- *
- */
-
-/dts-v1/;
-
-#include "r9a06g032.dtsi"
-
-/ {
-	model = "RZN1D-DB Board";
-	compatible = "renesas,rzn1d400-db", "renesas,r9a06g032";
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	aliases {
-		serial0 = &uart0;
-	};
-};
-
-&uart0 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/r9a06g032.dtsi b/arch/arm/boot/dts/r9a06g032.dtsi
deleted file mode 100644
index 4c1ab49c7d39..000000000000
--- a/arch/arm/boot/dts/r9a06g032.dtsi
+++ /dev/null
@@ -1,201 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Base Device Tree Source for the Renesas RZ/N1D (R9A06G032)
- *
- * Copyright (C) 2018 Renesas Electronics Europe Limited
- *
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/r9a06g032-sysctrl.h>
-
-/ {
-	compatible = "renesas,r9a06g032";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			reg = <0>;
-			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
-		};
-
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			reg = <1>;
-			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
-			enable-method = "renesas,r9a06g032-smp";
-			cpu-release-addr = <0 0x4000c204>;
-		};
-	};
-
-	ext_jtag_clk: extjtagclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	ext_mclk: extmclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <40000000>;
-	};
-
-	ext_rgmii_ref: extrgmiiref {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	ext_rtc_clk: extrtcclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		interrupt-parent = <&gic>;
-		ranges;
-
-		sysctrl: system-controller@4000c000 {
-			compatible = "renesas,r9a06g032-sysctrl";
-			reg = <0x4000c000 0x1000>;
-			status = "okay";
-			#clock-cells = <1>;
-
-			clocks = <&ext_mclk>, <&ext_rtc_clk>,
-					<&ext_jtag_clk>, <&ext_rgmii_ref>;
-			clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext";
-		};
-
-		uart0: serial@40060000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart", "snps,dw-apb-uart";
-			reg = <0x40060000 0x400>;
-			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART0>, <&sysctrl R9A06G032_HCLK_UART0>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart1: serial@40061000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart", "snps,dw-apb-uart";
-			reg = <0x40061000 0x400>;
-			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART1>, <&sysctrl R9A06G032_HCLK_UART1>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart2: serial@40062000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart", "snps,dw-apb-uart";
-			reg = <0x40062000 0x400>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART2>, <&sysctrl R9A06G032_HCLK_UART2>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart3: serial@50000000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
-			reg = <0x50000000 0x400>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART3>, <&sysctrl R9A06G032_HCLK_UART3>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart4: serial@50001000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
-			reg = <0x50001000 0x400>;
-			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART4>, <&sysctrl R9A06G032_HCLK_UART4>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart5: serial@50002000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
-			reg = <0x50002000 0x400>;
-			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART5>, <&sysctrl R9A06G032_HCLK_UART5>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart6: serial@50003000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
-			reg = <0x50003000 0x400>;
-			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART6>, <&sysctrl R9A06G032_HCLK_UART6>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		uart7: serial@50004000 {
-			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
-			reg = <0x50004000 0x400>;
-			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&sysctrl R9A06G032_CLK_UART7>, <&sysctrl R9A06G032_HCLK_UART7>;
-			clock-names = "baudclk", "apb_pclk";
-			status = "disabled";
-		};
-
-		pinctrl: pin-controller@40067000 {
-			compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl";
-			reg = <0x40067000 0x1000>, <0x51000000 0x480>;
-			clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>;
-			clock-names = "bus";
-			status = "okay";
-		};
-
-		gic: interrupt-controller@44101000 {
-			compatible = "arm,cortex-a7-gic", "arm,gic-400";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x44101000 0x1000>, /* Distributer */
-			      <0x44102000 0x2000>, /* CPU interface */
-			      <0x44104000 0x2000>, /* Virt interface control */
-			      <0x44106000 0x2000>; /* Virt CPU interface */
-			interrupts =
-				<GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
-		};
-	};
-
-	timer {
-		compatible = "arm,cortex-a7-timer",
-			     "arm,armv7-timer";
-		interrupt-parent = <&gic>;
-		arm,cpu-registers-not-fw-configured;
-		always-on;
-		interrupts =
-			<GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
-			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
-			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
-			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
-	};
-};
diff --git a/arch/arm/boot/dts/realtek/Makefile b/arch/arm/boot/dts/realtek/Makefile
new file mode 100644
index 000000000000..c83671b5560f
--- /dev/null
+++ b/arch/arm/boot/dts/realtek/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_REALTEK) += \
+	rtd1195-horseradish.dtb \
+	rtd1195-mele-x1000.dtb
diff --git a/arch/arm/boot/dts/realtek/rtd1195-horseradish.dts b/arch/arm/boot/dts/realtek/rtd1195-horseradish.dts
new file mode 100644
index 000000000000..9d06d3d34c74
--- /dev/null
+++ b/arch/arm/boot/dts/realtek/rtd1195-horseradish.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+/*
+ * Copyright (c) 2019 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "rtd1195.dtsi"
+
+/ {
+	compatible = "realtek,horseradish", "realtek,rtd1195";
+	model = "Realtek Horseradish EVB";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@a800 {
+		device_type = "memory";
+		reg = <0x0000a800 0x17ff5800>, /* boot ROM to r-bus */
+		      <0x18070000 0x00090000>, /* r-bus to NOR flash */
+		      <0x19100000 0x26f00000>; /* NOR flash to 1 GiB */
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/realtek/rtd1195-mele-x1000.dts b/arch/arm/boot/dts/realtek/rtd1195-mele-x1000.dts
new file mode 100644
index 000000000000..c7951b9a2c97
--- /dev/null
+++ b/arch/arm/boot/dts/realtek/rtd1195-mele-x1000.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+/*
+ * Copyright (c) 2017-2019 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "rtd1195.dtsi"
+
+/ {
+	compatible = "mele,x1000", "realtek,rtd1195";
+	model = "MeLE X1000";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@a800 {
+		device_type = "memory";
+		reg = <0x0000a800 0x17ff5800>, /* boot ROM to r-bus */
+		      <0x18070000 0x00090000>, /* r-bus to NOR flash */
+		      <0x19100000 0x26f00000>; /* NOR flash to 1 GiB */
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/realtek/rtd1195.dtsi b/arch/arm/boot/dts/realtek/rtd1195.dtsi
new file mode 100644
index 000000000000..21897210d9d0
--- /dev/null
+++ b/arch/arm/boot/dts/realtek/rtd1195.dtsi
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+/*
+ * Copyright (c) 2017-2019 Andreas Färber
+ */
+
+/memreserve/ 0x00000000 0x0000a800; /* boot code */
+/memreserve/ 0x0000a800 0x000f5800;
+/memreserve/ 0x17fff000 0x00001000;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/realtek,rtd1195.h>
+
+/ {
+	compatible = "realtek,rtd1195";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			clock-frequency = <1000000000>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rpc_comm: rpc@b000 {
+			reg = <0x0000b000 0x1000>;
+		};
+
+		audio@1b00000 {
+			reg = <0x01b00000 0x400000>;
+		};
+
+		rpc_ringbuf: rpc@1ffe000 {
+			reg = <0x01ffe000 0x4000>;
+		};
+
+		secure@10000000 {
+			reg = <0x10000000 0x100000>;
+			no-map;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <27000000>;
+	};
+
+	osc27M: osc {
+		compatible = "fixed-clock";
+		clock-frequency = <27000000>;
+		#clock-cells = <0>;
+		clock-output-names = "osc27M";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0x00000000 0x0000a800>,
+			 <0x18000000 0x18000000 0x00070000>,
+			 <0x18100000 0x18100000 0x01000000>,
+			 <0x80000000 0x80000000 0x80000000>;
+
+		rbus: bus@18000000 {
+			compatible = "simple-bus";
+			reg = <0x18000000 0x70000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x18000000 0x70000>;
+
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
+			};
+
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
+			};
+
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
+			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x1000>;
+			};
+		};
+
+		gic: interrupt-controller@ff011000 {
+			compatible = "arm,cortex-a7-gic";
+			reg = <0xff011000 0x1000>,
+			      <0xff012000 0x2000>,
+			      <0xff014000 0x2000>,
+			      <0xff016000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+	};
+};
+
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
+&iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
+	wdt: watchdog@680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x680 0x100>;
+		clocks = <&osc27M>;
+	};
+
+	uart0: serial@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		resets = <&iso_reset RTD1195_ISO_RSTN_UR0>;
+		clock-frequency = <27000000>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		resets = <&reset2 RTD1195_RSTN_UR1>;
+		clock-frequency = <27000000>;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm/boot/dts/renesas/Makefile b/arch/arm/boot/dts/renesas/Makefile
new file mode 100644
index 000000000000..833a02447ecf
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/Makefile
@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_RENESAS) += \
+	emev2-kzm9d.dtb \
+	r7s72100-genmai.dtb \
+	r7s72100-gr-peach.dtb \
+	r7s72100-rskrza1.dtb \
+	r7s9210-rza2mevb.dtb \
+	r8a73a4-ape6evm.dtb \
+	r8a7740-armadillo800eva.dtb \
+	r8a7742-iwg21d-q7.dtb \
+	r8a7742-iwg21d-q7-dbcm-ca.dtb \
+	r8a7743-iwg20d-q7.dtb \
+	r8a7743-iwg20d-q7-dbcm-ca.dtb \
+	r8a7743-sk-rzg1m.dtb \
+	r8a7744-iwg20d-q7.dtb \
+	r8a7744-iwg20d-q7-dbcm-ca.dtb \
+	r8a7745-iwg22d-sodimm.dtb \
+	r8a7745-iwg22d-sodimm-dbhd-ca.dtb \
+	r8a7745-sk-rzg1e.dtb \
+	r8a77470-iwg23s-sbc.dtb \
+	r8a7778-bockw.dtb \
+	r8a7779-marzen.dtb \
+	r8a7790-lager.dtb \
+	r8a7790-stout.dtb \
+	r8a7791-koelsch.dtb \
+	r8a7791-porter.dtb \
+	r8a7792-blanche.dtb \
+	r8a7792-wheat.dtb \
+	r8a7793-gose.dtb \
+	r8a7794-alt.dtb \
+	r8a7794-silk.dtb \
+	r9a06g032-rzn1d400-db.dtb \
+	sh73a0-kzm9g.dtb
diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/renesas/emev2-kzm9d.dts
index 0a27f034dd6b..89495dd37358 100644
--- a/arch/arm/boot/dts/emev2-kzm9d.dts
+++ b/arch/arm/boot/dts/renesas/emev2-kzm9d.dts
@@ -80,7 +80,7 @@
 	};
 
 	ethernet@20000000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan9221", "smsc,lan9115";
 		reg = <0x20000000 0x10000>;
 		phy-mode = "mii";
 		interrupt-parent = <&gpio0>;
diff --git a/arch/arm/boot/dts/emev2.dtsi b/arch/arm/boot/dts/renesas/emev2.dtsi
index 96678ddbb4e6..ecfaa0b7523e 100644
--- a/arch/arm/boot/dts/emev2.dtsi
+++ b/arch/arm/boot/dts/renesas/emev2.dtsi
@@ -195,7 +195,7 @@
 		clock-names = "sclk";
 	};
 
-	pfc: pin-controller@e0140200 {
+	pfc: pinctrl@e0140200 {
 		compatible = "renesas,pfc-emev2";
 		reg = <0xe0140200 0x100>;
 	};
diff --git a/arch/arm/boot/dts/gr-peach-audiocamerashield.dtsi b/arch/arm/boot/dts/renesas/gr-peach-audiocamerashield.dtsi
index 8d77579807ec..8d77579807ec 100644
--- a/arch/arm/boot/dts/gr-peach-audiocamerashield.dtsi
+++ b/arch/arm/boot/dts/renesas/gr-peach-audiocamerashield.dtsi
diff --git a/arch/arm/boot/dts/iwg20d-q7-common.dtsi b/arch/arm/boot/dts/renesas/iwg20d-q7-common.dtsi
index ae75a1db3d9a..4351c5a02fa5 100644
--- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi
+++ b/arch/arm/boot/dts/renesas/iwg20d-q7-common.dtsi
@@ -46,6 +46,50 @@
 		clock-frequency = <26000000>;
 	};
 
+	lcd_backlight: backlight {
+		compatible = "pwm-backlight";
+
+		pwms = <&pwm3 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>;
+	};
+
+	lvds-receiver {
+		compatible = "ti,ds90cf384a", "lvds-decoder";
+		power-supply = <&vcc_3v3_tft1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				lvds_receiver_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				lvds_receiver_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0dh6";
+		backlight = <&lcd_backlight>;
+		power-supply = <&vcc_3v3_tft1>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds_receiver_out>;
+			};
+		};
+	};
+
 	reg_1p5v: 1p5v {
 		compatible = "regulator-fixed";
 		regulator-name = "1P5V";
@@ -70,6 +114,17 @@
 		};
 	};
 
+	vcc_3v3_tft1: regulator-panel {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vcc-3v3-tft1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		startup-delay-us = <500>;
+		gpio = <&gpio7 25 GPIO_ACTIVE_HIGH>;
+	};
+
 	vcc_sdhi1: regulator-vcc-sdhi1 {
 		compatible = "regulator-fixed";
 
@@ -89,8 +144,7 @@
 
 		gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 };
 
@@ -104,6 +158,8 @@
 	status = "okay";
 
 	phy3: ethernet-phy@3 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		micrel,led-mode = <1>;
 	};
@@ -120,6 +176,18 @@
 	status = "okay";
 };
 
+&du {
+	status = "okay";
+};
+
+&gpio2 {
+	touch-interrupt-hog {
+		gpio-hog;
+		gpios = <12 GPIO_ACTIVE_LOW>;
+		input;
+	};
+};
+
 &hsusb {
 	status = "okay";
 	pinctrl-0 = <&usb0_pins>;
@@ -147,6 +215,26 @@
 		VDDIO-supply = <&reg_3p3v>;
 		VDDD-supply = <&reg_1p5v>;
 	};
+
+	touch: touchpanel@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&vcc_3v3_tft1>;
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_receiver_in>;
+			};
+		};
+	};
 };
 
 &pci0 {
@@ -180,6 +268,11 @@
 		function = "i2c2";
 	};
 
+	pwm3_pins: pwm3 {
+		groups = "pwm3";
+		function = "pwm3";
+	};
+
 	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
@@ -218,6 +311,12 @@
 	};
 };
 
+&pwm3 {
+	pinctrl-0 = <&pwm3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
 &rcar_sound {
 	pinctrl-0 = <&sound_pins>;
 	pinctrl-names = "default";
@@ -228,8 +327,8 @@
 
 	rcar_sound,dai {
 		dai0 {
-			playback = <&ssi1 &src3 &dvc1>;
-			capture = <&ssi0 &src2 &dvc0>;
+			playback = <&ssi1>, <&src3>, <&dvc1>;
+			capture = <&ssi0>, <&src2>, <&dvc0>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi b/arch/arm/boot/dts/renesas/iwg20d-q7-dbcm-ca.dtsi
index 0e99df218252..de52218ceaa4 100644
--- a/arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi
+++ b/arch/arm/boot/dts/renesas/iwg20d-q7-dbcm-ca.dtsi
@@ -27,6 +27,15 @@
 			};
 		};
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &can1 {
@@ -39,7 +48,6 @@
 &du {
 	pinctrl-0 = <&du_pins>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	ports {
 		port@0 {
@@ -70,11 +78,15 @@
 		clocks = <&cec_clock>;
 		clock-names = "cec";
 
+		avdd-supply = <&reg_1p8v>;
+		dvdd-supply = <&reg_1p8v>;
+		pvdd-supply = <&reg_1p8v>;
+		dvdd-3v-supply = <&reg_3p3v>;
+		bgvdd-supply = <&reg_1p8v>;
+
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/r7s72100-genmai.dts b/arch/arm/boot/dts/renesas/r7s72100-genmai.dts
index 07d611d2b7b5..29ba098f5dd5 100644
--- a/arch/arm/boot/dts/r7s72100-genmai.dts
+++ b/arch/arm/boot/dts/renesas/r7s72100-genmai.dts
@@ -29,9 +29,33 @@
 		reg = <0x08000000 0x08000000>;
 	};
 
-	lbsc {
+	flash@18000000 {
+		compatible = "mtd-rom";
+		reg = <0x18000000 0x08000000>;
+		bank-width = <4>;
+		device-width = <1>;
+
+		clocks = <&mstp9_clks R7S72100_CLK_SPIBSC0>;
+		power-domains = <&cpg_clocks>;
+
 		#address-cells = <1>;
 		#size-cells = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "user";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "user1";
+				reg = <0x04000000 0x40000000>;
+			};
+		};
 	};
 
 	leds {
@@ -87,6 +111,62 @@
 	clock-frequency = <13330000>;
 };
 
+&bsc {
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0x00000000 0x04000000>;
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x00000000 0x00040000>;
+			};
+
+			partition@40000 {
+				label = "uboot-env";
+				reg = <0x00040000 0x00020000>;
+			};
+
+			partition@60000 {
+				label = "flash";
+				reg = <0x00060000 0x03fa0000>;
+			};
+		};
+	};
+
+	flash@4000000 {
+		compatible = "cfi-flash";
+		reg = <0x04000000 0x04000000>;
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot1";
+				reg = <0x00000000 0x00040000>;
+			};
+
+			partition@40000 {
+				label = "uboot-env1";
+				reg = <0x00040000 0x00020000>;
+			};
+
+			partition@60000 {
+				label = "flash1";
+				reg = <0x00060000 0x03fa0000>;
+			};
+		};
+	};
+};
+
 &usb_x1_clk {
 	clock-frequency = <48000000>;
 };
@@ -108,6 +188,8 @@
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-idb824.2814",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 	};
 };
diff --git a/arch/arm/boot/dts/r7s72100-gr-peach.dts b/arch/arm/boot/dts/renesas/r7s72100-gr-peach.dts
index fe1a4aa4d7cb..9d29861f23f1 100644
--- a/arch/arm/boot/dts/r7s72100-gr-peach.dts
+++ b/arch/arm/boot/dts/renesas/r7s72100-gr-peach.dts
@@ -29,18 +29,15 @@
 		reg = <0x20000000 0x00a00000>;
 	};
 
-	lbsc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-
 	flash@18000000 {
 		compatible = "mtd-rom";
-		probe-type = "map_rom";
 		reg = <0x18000000 0x00800000>;
 		bank-width = <4>;
 		device-width = <1>;
 
+		clocks = <&mstp9_clks R7S72100_CLK_SPIBSC0>;
+		power-domains = <&cpg_clocks>;
+
 		#address-cells = <1>;
 		#size-cells = <1>;
 
@@ -126,6 +123,8 @@
 	phy-handle = <&phy0>;
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 
 		reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/r7s72100-rskrza1.dts b/arch/arm/boot/dts/renesas/r7s72100-rskrza1.dts
index 99acfe4fe11a..b547216d4801 100644
--- a/arch/arm/boot/dts/r7s72100-rskrza1.dts
+++ b/arch/arm/boot/dts/renesas/r7s72100-rskrza1.dts
@@ -29,6 +29,48 @@
 		reg = <0x08000000 0x02000000>;
 	};
 
+	flash@18000000 {
+		compatible = "mtd-rom";
+		reg = <0x18000000 0x08000000>;
+		clocks = <&mstp9_clks R7S72100_CLK_SPIBSC0>;
+		power-domains = <&cpg_clocks>;
+		bank-width = <4>;
+		device-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x00000000 0x00080000>;
+			};
+
+			partition@80000 {
+				label = "uboot-env";
+				reg = <0x00080000 0x00040000>;
+			};
+
+			partition@c0000 {
+				label = "dt";
+				reg = <0x000c0000 0x00040000>;
+			};
+
+			partition@100000 {
+				label = "kernel";
+				reg = <0x00100000 0x00280000>;
+			};
+
+			partition@400000 {
+				label = "rootfs";
+				reg = <0x00400000 0x01c00000>;
+			};
+		};
+	};
+
 	keyboard {
 		compatible = "gpio-keys";
 
@@ -60,11 +102,6 @@
 		};
 	};
 
-	lbsc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -118,6 +155,30 @@
 	};
 };
 
+&bsc {
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0x00000000 0x4000000>;
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "apps";
+				reg = <0x00000000 0x01000000>;
+			};
+
+			partition@1000000 {
+				label = "data";
+				reg = <0x01000000 0x03000000>;
+			};
+		};
+	};
+};
+
 &usb_x1_clk {
 	clock-frequency = <48000000>;
 };
@@ -192,6 +253,8 @@
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-idb824.2814",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 	};
 };
diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/renesas/r7s72100.dtsi
index d03dcd919d6f..e6d8da6faffb 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/renesas/r7s72100.dtsi
@@ -36,6 +36,13 @@
 		clock-div = <3>;
 	};
 
+	bsc: bsc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0x18000000>;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -313,9 +320,9 @@
 		mmcif: mmc@e804c800 {
 			compatible = "renesas,mmcif-r7s72100", "renesas,sh-mmcif";
 			reg = <0xe804c800 0x80>;
-			interrupts = <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp8_clks R7S72100_CLK_MMCIF>;
 			power-domains = <&cpg_clocks>;
 			reg-io-width = <4>;
@@ -323,12 +330,12 @@
 			status = "disabled";
 		};
 
-		sdhi0: sd@e804e000 {
+		sdhi0: mmc@e804e000 {
 			compatible = "renesas,sdhi-r7s72100";
 			reg = <0xe804e000 0x100>;
-			interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&mstp12_clks R7S72100_CLK_SDHI00>,
 				 <&mstp12_clks R7S72100_CLK_SDHI01>;
@@ -339,12 +346,12 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@e804e800 {
+		sdhi1: mmc@e804e800 {
 			compatible = "renesas,sdhi-r7s72100";
 			reg = <0xe804e800 0x100>;
-			interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&mstp12_clks R7S72100_CLK_SDHI10>,
 				 <&mstp12_clks R7S72100_CLK_SDHI11>;
@@ -467,11 +474,12 @@
 			#clock-cells = <1>;
 			compatible = "renesas,r7s72100-mstp-clocks", "renesas,cpg-mstp-clocks";
 			reg = <0xfcfe0438 4>;
-			clocks = <&p0_clk>, <&p0_clk>, <&p0_clk>, <&p0_clk>;
+			clocks = <&p0_clk>, <&p0_clk>, <&p0_clk>, <&p0_clk>, <&b_clk>, <&b_clk>;
 			clock-indices = <
 				R7S72100_CLK_I2C0 R7S72100_CLK_I2C1 R7S72100_CLK_I2C2 R7S72100_CLK_I2C3
+				R7S72100_CLK_SPIBSC0 R7S72100_CLK_SPIBSC1
 			>;
-			clock-output-names = "i2c0", "i2c1", "i2c2", "i2c3";
+			clock-output-names = "i2c0", "i2c1", "i2c2", "i2c3", "spibsc0", "spibsc1";
 		};
 
 		mstp10_clks: mstp10_clks@fcfe043c {
@@ -498,7 +506,7 @@
 			clock-output-names = "sdhi00", "sdhi01", "sdhi10", "sdhi11";
 		};
 
-		pinctrl: pin-controller@fcfe3000 {
+		pinctrl: pinctrl@fcfe3000 {
 			compatible = "renesas,r7s72100-ports";
 
 			reg = <0xfcfe3000 0x4230>;
@@ -607,6 +615,8 @@
 				     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&mstp9_clks R7S72100_CLK_I2C0>;
 			clock-frequency = <100000>;
 			power-domains = <&cpg_clocks>;
@@ -626,6 +636,8 @@
 				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&mstp9_clks R7S72100_CLK_I2C1>;
 			clock-frequency = <100000>;
 			power-domains = <&cpg_clocks>;
@@ -645,6 +657,8 @@
 				     <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&mstp9_clks R7S72100_CLK_I2C2>;
 			clock-frequency = <100000>;
 			power-domains = <&cpg_clocks>;
@@ -664,6 +678,8 @@
 				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&mstp9_clks R7S72100_CLK_I2C3>;
 			clock-frequency = <100000>;
 			power-domains = <&cpg_clocks>;
diff --git a/arch/arm/boot/dts/r7s9210-rza2mevb.dts b/arch/arm/boot/dts/renesas/r7s9210-rza2mevb.dts
index d062d02865e7..cd2324b8e8ff 100644
--- a/arch/arm/boot/dts/r7s9210-rza2mevb.dts
+++ b/arch/arm/boot/dts/renesas/r7s9210-rza2mevb.dts
@@ -4,6 +4,28 @@
  *
  * Copyright (C) 2018 Renesas Electronics
  *
+ * As upstream Linux does not support XIP, it cannot run in 8 MiB of HyperRAM.
+ * Hence the 64 MiB of SDRAM on the sub-board needs to be enabled, which has
+ * the following ramifications:
+ *   - SCIF4 connected to the on-board USB-serial can no longer be used as the
+ *     serial console,
+ *   - Instead, SCIF2 is used as the serial console, by connecting a 3.3V TTL
+ *     USB-to-Serial adapter to the CMOS camera connector:
+ *       - RXD = CN17-9,
+ *       - TXD = CN17-10,
+ *       - GND = CN17-2 or CN17-17,
+ *   - The first Ethernet channel can no longer be used,
+ *   - USB Channel 1 loses the overcurrent input signal.
+ *
+ * Please make sure your sub-board matches the following switch settings:
+ *
+ *           SW6                SW6-1 set to SDRAM
+ *  ON                          SW6-2 set to Audio
+ * +---------------------+      SW6-3 set to DRP
+ * | =   =   = = =       |      SW6-4 set to CEU
+ * |   =   =             |      SW6-5 set to Ether2
+ * | 1 2 3 4 5 6 7 8 9 0 |      SW6-6 set to VDC6
+ * +---------------------+      SW6-7 set to VDC6
  */
 
 /dts-v1/;
@@ -17,9 +39,8 @@
 	compatible = "renesas,rza2mevb", "renesas,r7s9210";
 
 	aliases {
-		serial0 = &scif4;
-		ethernet0 = &ether0;
-		ethernet1 = &ether1;
+		serial0 = &scif2;
+		ethernet0 = &ether1;
 	};
 
 	chosen {
@@ -42,25 +63,20 @@
 		};
 	};
 
-	lbsc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-red {
 			gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
 		};
-		green {
+		led-green {
 			gpios = <&pinctrl RZA2_PIN(PORTC, 1) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
-	memory@40000000 {
+	memory@c000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x00800000>;	 /* HyperRAM */
+		reg = <0x0c000000 0x04000000>;	/* SDRAM */
 	};
 };
 
@@ -72,17 +88,6 @@
 	status = "okay";
 };
 
-&ether0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&eth0_pins>;
-	status = "okay";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-};
-
 &ether1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&eth1_pins>;
@@ -90,6 +95,8 @@
 	renesas,no-ether-link;
 	phy-handle = <&phy1>;
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id001c.c816",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 	};
 };
@@ -99,6 +106,20 @@
 	clock-frequency = <24000000>;	/* 24MHz */
 };
 
+&i2c3 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	eeprom@50 {
+		compatible = "renesas,r1ex24128", "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <64>;
+	};
+};
+
 /* High resolution System tick timers */
 &ostm0 {
 	status = "okay";
@@ -137,14 +158,19 @@
 			 <RZA2_PINMUX(PORTL, 1, 5)>; /* IRQ5 */
 	};
 
+	i2c3_pins: i2c3 {
+		pinmux = <RZA2_PINMUX(PORTD, 6, 1)>,	/* RIIC3SCL */
+			 <RZA2_PINMUX(PORTD, 7, 1)>;	/* RIIC3SDA */
+	};
+
 	keyboard_pins: keyboard {
 		pinmux = <RZA2_PINMUX(PORTJ, 1, 6)>;	/* IRQ0 */
 	};
 
 	/* Serial Console */
-	scif4_pins: serial4 {
-		pinmux = <RZA2_PINMUX(PORT9, 0, 4)>,	/* TxD4 */
-			 <RZA2_PINMUX(PORT9, 1, 4)>;	/* RxD4 */
+	scif2_pins: serial2 {
+		pinmux = <RZA2_PINMUX(PORTE, 2, 3)>,	/* TxD2 */
+			 <RZA2_PINMUX(PORTE, 1, 3)>;	/* RxD2 */
 	};
 
 	sdhi0_pins: sdhi0 {
@@ -165,8 +191,7 @@
 
 	usb1_pins: usb1 {
 		pinmux = <RZA2_PINMUX(PORTC, 0, 1)>,	/* VBUSIN1 */
-			 <RZA2_PINMUX(PORTC, 5, 1)>,	/* VBUSEN1 */
-			 <RZA2_PINMUX(PORT7, 5, 5)>;	/* OVRCUR1 */
+			 <RZA2_PINMUX(PORTC, 5, 1)>;	/* VBUSEN1 */
 	};
 };
 
@@ -176,9 +201,9 @@
 };
 
 /* Serial Console */
-&scif4 {
+&scif2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&scif4_pins>;
+	pinctrl-0 = <&scif2_pins>;
 
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/r7s9210.dtsi b/arch/arm/boot/dts/renesas/r7s9210.dtsi
index 72b79770e336..fdeb0bc12cb7 100644
--- a/arch/arm/boot/dts/r7s9210.dtsi
+++ b/arch/arm/boot/dts/renesas/r7s9210.dtsi
@@ -236,6 +236,8 @@
 				     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&cpg CPG_MOD 87>;
 			power-domains = <&cpg>;
 			clock-frequency = <100000>;
@@ -255,6 +257,8 @@
 				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&cpg CPG_MOD 86>;
 			power-domains = <&cpg>;
 			clock-frequency = <100000>;
@@ -274,6 +278,8 @@
 				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&cpg CPG_MOD 85>;
 			power-domains = <&cpg>;
 			clock-frequency = <100000>;
@@ -293,6 +299,8 @@
 				     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
 			clocks = <&cpg CPG_MOD 84>;
 			power-domains = <&cpg>;
 			clock-frequency = <100000>;
@@ -304,7 +312,6 @@
 			reg = <0xe803b000 0x30>;
 			interrupts = <GIC_SPI 56 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&cpg CPG_MOD 36>;
-			clock-names = "ostm0";
 			power-domains = <&cpg>;
 			status = "disabled";
 		};
@@ -314,7 +321,6 @@
 			reg = <0xe803c000 0x30>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&cpg CPG_MOD 35>;
-			clock-names = "ostm1";
 			power-domains = <&cpg>;
 			status = "disabled";
 		};
@@ -324,7 +330,6 @@
 			reg = <0xe803d000 0x30>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&cpg CPG_MOD 34>;
-			clock-names = "ostm2";
 			power-domains = <&cpg>;
 			status = "disabled";
 		};
@@ -419,7 +424,7 @@
 			status = "disabled";
 		};
 
-		sdhi0: sd@e8228000 {
+		sdhi0: mmc@e8228000 {
 			compatible = "renesas,sdhi-r7s9210";
 			reg = <0xe8228000 0x8c0>;
 			interrupts = <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>;
@@ -431,7 +436,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@e822a000 {
+		sdhi1: mmc@e822a000 {
 			compatible = "renesas,sdhi-r7s9210";
 			reg = <0xe822a000 0x8c0>;
 			interrupts = <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>;
@@ -492,7 +497,7 @@
 			interrupt-map-mask = <7 0>;
 		};
 
-		pinctrl: pin-controller@fcffe000 {
+		pinctrl: pinctrl@fcffe000 {
 			compatible = "renesas,r7s9210-pinctrl";
 			reg = <0xfcffe000 0x1000>;
 
diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dts
index a5351ddbf506..ed75c01dbee1 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dts
@@ -157,17 +157,14 @@
 
 &cpu0 {
 	cpu0-supply = <&vdd_dvfs>;
-	operating-points = <
-		/* kHz  uV */
-		1950000 1115000
-		1462500  995000
-	>;
+	operating-points = <1950000 1115000>,	/* kHz  uV */
+			   <1462500  995000>;
 	voltage-tolerance = <1>; /* 1% */
 };
 
 &bsc {
 	flash@0 {
-		compatible = "cfi-flash", "mtd-rom";
+		compatible = "cfi-flash";
 		reg = <0x0 0x08000000>;
 		bank-width = <2>;
 
@@ -202,6 +199,7 @@
 		reg-io-width = <4>;
 		smsc,irq-active-high;
 		smsc,irq-push-pull;
+		reset-gpios = <&pfc 270 GPIO_ACTIVE_LOW>;
 		vdd33a-supply = <&ape6evm_fixed_3v3>;
 		vddvario-supply = <&ape6evm_fixed_1v8>;
 	};
diff --git a/arch/arm/boot/dts/r8a73a4.dtsi b/arch/arm/boot/dts/renesas/r8a73a4.dtsi
index dd865f3c2eda..c39066967053 100644
--- a/arch/arm/boot/dts/r8a73a4.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a73a4.dtsi
@@ -72,50 +72,6 @@
 		power-domains = <&pd_a3bc>;
 	};
 
-	dmac: dma-multiplexer {
-		compatible = "renesas,shdma-mux";
-		#dma-cells = <1>;
-		dma-channels = <20>;
-		dma-requests = <256>;
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		dma0: dma-controller@e6700020 {
-			compatible = "renesas,shdma-r8a73a4";
-			reg = <0 0xe6700020 0 0x89e0>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-					GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "error",
-					"ch0", "ch1", "ch2", "ch3",
-					"ch4", "ch5", "ch6", "ch7",
-					"ch8", "ch9", "ch10", "ch11",
-					"ch12", "ch13", "ch14", "ch15",
-					"ch16", "ch17", "ch18", "ch19";
-			clocks = <&mstp2_clks R8A73A4_CLK_DMAC>;
-			power-domains = <&pd_a3sp>;
-		};
-	};
-
 	i2c5: i2c@e60b0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -131,7 +87,14 @@
 	cmt1: timer@e6130000 {
 		compatible = "renesas,r8a73a4-cmt1", "renesas,rcar-gen2-cmt1";
 		reg = <0 0xe6130000 0 0x1004>;
-		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A73A4_CLK_CMT1>;
 		clock-names = "fck";
 		power-domains = <&pd_c5>;
@@ -214,7 +177,7 @@
 		power-domains = <&pd_c4>;
 	};
 
-	pfc: pin-controller@e6050000 {
+	pfc: pinctrl@e6050000 {
 		compatible = "renesas,pfc-r8a73a4";
 		reg = <0 0xe6050000 0 0x9000>;
 		gpio-controller;
@@ -402,7 +365,7 @@
 		status = "disabled";
 	};
 
-	sdhi0: sd@ee100000 {
+	sdhi0: mmc@ee100000 {
 		compatible = "renesas,sdhi-r8a73a4";
 		reg = <0 0xee100000 0 0x100>;
 		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
@@ -412,7 +375,7 @@
 		status = "disabled";
 	};
 
-	sdhi1: sd@ee120000 {
+	sdhi1: mmc@ee120000 {
 		compatible = "renesas,sdhi-r8a73a4";
 		reg = <0 0xee120000 0 0x100>;
 		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
@@ -422,7 +385,7 @@
 		status = "disabled";
 	};
 
-	sdhi2: sd@ee140000 {
+	sdhi2: mmc@ee140000 {
 		compatible = "renesas,sdhi-r8a73a4";
 		reg = <0 0xee140000 0 0x100>;
 		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/renesas/r8a7740-armadillo800eva.dts
index 758360a2edc3..e1ac2c161e73 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
+++ b/arch/arm/boot/dts/renesas/r8a7740-armadillo800eva.dts
@@ -58,10 +58,9 @@
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc_sdhi0>;
 
-		enable-gpio = <&pfc 74 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&pfc 74 GPIO_ACTIVE_HIGH>;
 		gpios = <&pfc 17 GPIO_ACTIVE_HIGH>;
-		states = <3300000 0
-			  1800000 1>;
+		states = <3300000 0>, <1800000 1>;
 
 		enable-active-high;
 	};
@@ -133,7 +132,7 @@
 		i2c-gpio,delay-us = <5>;
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&tpu 2 33333 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 1 2 4 8 16 32 64 128 255>;
@@ -144,6 +143,18 @@
 		enable-gpios = <&pfc 61 GPIO_ACTIVE_HIGH>;
 	};
 
+	panel {
+		compatible = "ampire,am-800480l1tmqw-t00h";
+		backlight = <&backlight>;
+		power-supply = <&reg_5p0v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lcdc0_rgb>;
+			};
+		};
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 
@@ -171,7 +182,10 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f1",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
+		reset-gpios = <&pfc 18 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -194,6 +208,19 @@
 
 &i2c0 {
 	status = "okay";
+
+	wm8978: codec@1a {
+		#sound-dai-cells = <0>;
+		compatible = "wlf,wm8978";
+		reg = <0x1a>;
+	};
+
+	eeprom@50 {
+		compatible = "st,24c01", "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
 	touchscreen@55 {
 		compatible = "sitronix,st1232";
 		reg = <0x55>;
@@ -203,12 +230,6 @@
 		pinctrl-names = "default";
 		gpios = <&pfc 166 GPIO_ACTIVE_LOW>;
 	};
-
-	wm8978: codec@1a {
-		#sound-dai-cells = <0>;
-		compatible = "wlf,wm8978";
-		reg = <0x1a>;
-	};
 };
 
 &i2c2 {
@@ -219,10 +240,22 @@
 	};
 };
 
-&pfc {
+&lcdc0 {
 	pinctrl-0 = <&lcd0_pins>;
 	pinctrl-names = "default";
 
+	status = "okay";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pfc {
 	ether_pins: ether {
 		groups = "gether_mii", "gether_int";
 		function = "gether";
@@ -264,7 +297,7 @@
 		function = "lcd0";
 	};
 
-	lcd0_mux {
+	lcd0-mux-hog {
 		/* DBGMD/LCDC0/FSIA MUX */
 		gpio-hog;
 		gpios = <176 0>;
diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/renesas/r8a7740.dtsi
index 12ffe73bf2bc..55884ec701f8 100644
--- a/arch/arm/boot/dts/r8a7740.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7740.dtsi
@@ -83,7 +83,7 @@
 	};
 
 	cmt1: timer@e6138000 {
-		compatible = "renesas,cmt-48-r8a7740", "renesas,cmt-48";
+		compatible = "renesas,r8a7740-cmt1";
 		reg = <0xe6138000 0x170>;
 		interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7740_CLK_CMT1>;
@@ -102,14 +102,14 @@
 			<0xe6900020 1>,
 			<0xe6900040 1>,
 			<0xe6900060 1>;
-		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7740_CLK_INTCA>;
 		power-domains = <&pd_a4s>;
 	};
@@ -124,14 +124,14 @@
 			<0xe6900024 1>,
 			<0xe6900044 1>,
 			<0xe6900064 1>;
-		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7740_CLK_INTCA>;
 		power-domains = <&pd_a4s>;
 	};
@@ -146,14 +146,14 @@
 			<0xe6900028 1>,
 			<0xe6900048 1>,
 			<0xe6900068 1>;
-		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7740_CLK_INTCA>;
 		power-domains = <&pd_a4s>;
 	};
@@ -168,14 +168,14 @@
 			<0xe690002c 1>,
 			<0xe690004c 1>,
 			<0xe690006c 1>;
-		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7740_CLK_INTCA>;
 		power-domains = <&pd_a4s>;
 	};
@@ -198,10 +198,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-r8a7740", "renesas,rmobile-iic";
 		reg = <0xfff20000 0x425>;
-		interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp1_clks R8A7740_CLK_IIC0>;
 		power-domains = <&pd_a4r>;
 		status = "disabled";
@@ -212,10 +212,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-r8a7740", "renesas,rmobile-iic";
 		reg = <0xe6c20000 0x425>;
-		interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7740_CLK_IIC1>;
 		power-domains = <&pd_a3sp>;
 		status = "disabled";
@@ -311,7 +311,7 @@
 		status = "disabled";
 	};
 
-	pfc: pin-controller@e6050000 {
+	pfc: pinctrl@e6050000 {
 		compatible = "renesas,pfc-r8a7740";
 		reg = <0xe6050000 0x8000>,
 		      <0xe605800c 0x20>;
@@ -342,19 +342,19 @@
 	mmcif0: mmc@e6bd0000 {
 		compatible = "renesas,mmcif-r8a7740", "renesas,sh-mmcif";
 		reg = <0xe6bd0000 0x100>;
-		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7740_CLK_MMC>;
 		power-domains = <&pd_a3sp>;
 		status = "disabled";
 	};
 
-	sdhi0: sd@e6850000 {
+	sdhi0: mmc@e6850000 {
 		compatible = "renesas,sdhi-r8a7740";
 		reg = <0xe6850000 0x100>;
-		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7740_CLK_SDHI0>;
 		power-domains = <&pd_a3sp>;
 		cap-sd-highspeed;
@@ -362,12 +362,12 @@
 		status = "disabled";
 	};
 
-	sdhi1: sd@e6860000 {
+	sdhi1: mmc@e6860000 {
 		compatible = "renesas,sdhi-r8a7740";
 		reg = <0xe6860000 0x100>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7740_CLK_SDHI1>;
 		power-domains = <&pd_a3sp>;
 		cap-sd-highspeed;
@@ -375,12 +375,12 @@
 		status = "disabled";
 	};
 
-	sdhi2: sd@e6870000 {
+	sdhi2: mmc@e6870000 {
 		compatible = "renesas,sdhi-r8a7740";
 		reg = <0xe6870000 0x100>;
-		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp4_clks R8A7740_CLK_SDHI2>;
 		power-domains = <&pd_a3sp>;
 		cap-sd-highspeed;
@@ -398,6 +398,61 @@
 		status = "disabled";
 	};
 
+	lcdc0: lcd-controller@fe940000 {
+		compatible = "renesas,r8a7740-lcdc";
+		reg = <0xfe940000 0x4000>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7740_CLK_LCDC0>,
+			 <&cpg_clocks R8A7740_CLK_M3>, <&lcdlclk0_clk>,
+			 <&vou_clk>;
+		clock-names = "fck", "media", "lclk", "video";
+		power-domains = <&pd_a4lc>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lcdc0_rgb: endpoint {
+				};
+			};
+		};
+	};
+
+	lcdc1: lcd-controller@fe944000 {
+		compatible = "renesas,r8a7740-lcdc";
+		reg = <0xfe944000 0x4000>;
+		interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7740_CLK_LCDC1>,
+			 <&cpg_clocks R8A7740_CLK_M3>, <&lcdlclk1_clk>,
+			 <&vou_clk>;
+		clock-names = "fck", "media", "lclk", "video";
+		power-domains = <&pd_a4lc>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lcdc1_rgb: endpoint {
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lcdc1_hdmi: endpoint {
+				};
+			};
+		};
+	};
+
 	tmu0: timer@fff80000 {
 		compatible = "renesas,tmu-r8a7740", "renesas,tmu";
 		reg = <0xfff80000 0x2c>;
@@ -474,12 +529,22 @@
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
+		lcdlclk0_clk: lcdlclk0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+		lcdlclk1_clk: lcdlclk1 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
 
 		/* Special CPG clocks */
 		cpg_clocks: cpg_clocks@e6150000 {
 			compatible = "renesas,r8a7740-cpg-clocks";
 			reg = <0xe6150000 0x10000>;
-			clocks = <&extal1_clk>, <&extalr_clk>;
+			clocks = <&extal1_clk>, <&extal2_clk>, <&extalr_clk>;
 			#clock-cells = <1>;
 			clock-output-names = "system", "pllc0", "pllc1",
 					     "pllc2", "r",
diff --git a/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ca.dts
new file mode 100644
index 000000000000..33ac4bd1e63b
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ca.dts
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the iWave-RZ/G1H Qseven board development
+ * platform with camera daughter board
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/media/video-interfaces.h>
+
+#include "r8a7742-iwg21d-q7.dts"
+
+/ {
+	model = "iWave Systems RZ/G1H Qseven development platform with camera add-on";
+	compatible = "iwave,g21d", "iwave,g21m", "renesas,r8a7742";
+
+	aliases {
+		serial0 = &scif0;
+		serial1 = &scif1;
+		serial3 = &scifb1;
+		serial5 = &hscif0;
+		ethernet1 = &ether;
+	};
+
+	mclk_cam1: mclk-cam1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	mclk_cam2: mclk-cam2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	mclk_cam3: mclk-cam3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	mclk_cam4: mclk-cam4 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	reg_1p8v: 1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_2p8v: 2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+};
+
+&avb {
+	/* Pins shared with VIN0, keep status disabled */
+	status = "disabled";
+};
+
+&can0 {
+	pinctrl-0 = <&can0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&ether {
+	pinctrl-0 = <&ether_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&phy1>;
+	renesas,ether-link-active-low;
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1560",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		micrel,led-mode = <1>;
+	};
+};
+
+&gpio0 {
+	/* Disable hogging GP0_18 to output LOW */
+	/delete-node/ qspi-en-hog;
+
+	/* Hog GP0_18 to output HIGH to enable VIN2 */
+	vin2-en-hog {
+		gpio-hog;
+		gpios = <18 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "VIN2_EN";
+	};
+};
+
+&hscif0 {
+	pinctrl-0 = <&hscif0_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	/* status set to "okay" when needed by camera configuration below */
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+
+	/* status set to "okay" when needed by camera configuration below */
+	clock-frequency = <400000>;
+};
+
+&pfc {
+	can0_pins: can0 {
+		groups = "can0_data_d";
+		function = "can0";
+	};
+
+	ether_pins: ether {
+		groups = "eth_mdio", "eth_rmii";
+		function = "eth";
+	};
+
+	hscif0_pins: hscif0 {
+		groups = "hscif0_data", "hscif0_ctrl";
+		function = "hscif0";
+	};
+
+	i2c1_pins: i2c1 {
+		groups = "i2c1_c";
+		function = "i2c1";
+	};
+
+	i2c3_pins: i2c3 {
+		groups = "i2c3";
+		function = "i2c3";
+	};
+
+	scif0_pins: scif0 {
+		groups = "scif0_data";
+		function = "scif0";
+	};
+
+	scif1_pins: scif1 {
+		groups = "scif1_data";
+		function = "scif1";
+	};
+
+	scifb1_pins: scifb1 {
+		groups = "scifb1_data";
+		function = "scifb1";
+	};
+
+	vin0_8bit_pins: vin0 {
+		groups = "vin0_data8", "vin0_clk", "vin0_sync";
+		function = "vin0";
+	};
+
+	vin1_8bit_pins: vin1 {
+		groups = "vin1_data8_b", "vin1_clk_b", "vin1_sync_b";
+		function = "vin1";
+	};
+
+	vin2_pins: vin2 {
+		groups = "vin2_g8", "vin2_clk";
+		function = "vin2";
+	};
+
+	vin3_pins: vin3 {
+		groups = "vin3_data8", "vin3_clk", "vin3_sync";
+		function = "vin3";
+	};
+};
+
+&qspi {
+	/* Pins shared with VIN2, keep status disabled */
+	status = "disabled";
+};
+
+&scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&scif1 {
+	pinctrl-0 = <&scif1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&scifb1 {
+	pinctrl-0 = <&scifb1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rts-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+};
+
+/*
+ * Below configuration ties VINx endpoints to ov5640/ov7725 camera endpoints
+ *
+ * (un)comment the #include statements to change configuration
+ */
+
+/* 8bit CMOS Camera 1 (J13) */
+#define CAM_PARENT_I2C		i2c0
+#define MCLK_CAM		mclk_cam1
+#define CAM_EP			cam0ep
+#define VIN_EP			vin0ep
+#undef CAM_ENABLED
+#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
+//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi"
+
+#ifdef CAM_ENABLED
+&vin0 {
+	/*
+	 * Set SW2 switch on the SOM to 'ON'
+	 * Set SW1 switch on camera board to 'OFF' as we are using 8bit mode
+	 */
+	status = "okay";
+	pinctrl-0 = <&vin0_8bit_pins>;
+	pinctrl-names = "default";
+
+	port {
+		vin0ep: endpoint {
+			remote-endpoint = <&cam0ep>;
+			bus-width = <8>;
+			bus-type = <MEDIA_BUS_TYPE_BT656>;
+		};
+	};
+};
+#endif /* CAM_ENABLED */
+
+#undef CAM_PARENT_I2C
+#undef MCLK_CAM
+#undef CAM_EP
+#undef VIN_EP
+
+/* 8bit CMOS Camera 2 (J14) */
+#define CAM_PARENT_I2C		i2c1
+#define MCLK_CAM		mclk_cam2
+#define CAM_EP			cam1ep
+#define VIN_EP			vin1ep
+#undef CAM_ENABLED
+#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
+//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi"
+
+#ifdef CAM_ENABLED
+&vin1 {
+	/* Set SW1 switch on the SOM to 'ON' */
+	status = "okay";
+	pinctrl-0 = <&vin1_8bit_pins>;
+	pinctrl-names = "default";
+
+	port {
+		vin1ep: endpoint {
+			remote-endpoint = <&cam1ep>;
+			bus-width = <8>;
+			bus-type = <MEDIA_BUS_TYPE_BT656>;
+		};
+	};
+};
+
+#endif /* CAM_ENABLED */
+
+#undef CAM_PARENT_I2C
+#undef MCLK_CAM
+#undef CAM_EP
+#undef VIN_EP
+
+/* 8bit CMOS Camera 3 (J12) */
+#define CAM_PARENT_I2C		i2c2
+#define MCLK_CAM		mclk_cam3
+#define CAM_EP			cam2ep
+#define VIN_EP			vin2ep
+#undef CAM_ENABLED
+#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
+//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi"
+
+#ifdef CAM_ENABLED
+&vin2 {
+	status = "okay";
+	pinctrl-0 = <&vin2_pins>;
+	pinctrl-names = "default";
+
+	port {
+		vin2ep: endpoint {
+			remote-endpoint = <&cam2ep>;
+			bus-width = <8>;
+			data-shift = <8>;
+			bus-type = <MEDIA_BUS_TYPE_BT656>;
+		};
+	};
+};
+#endif /* CAM_ENABLED */
+
+#undef CAM_PARENT_I2C
+#undef MCLK_CAM
+#undef CAM_EP
+#undef VIN_EP
+
+/* 8bit CMOS Camera 4 (J11) */
+#define CAM_PARENT_I2C		i2c3
+#define MCLK_CAM		mclk_cam4
+#define CAM_EP			cam3ep
+#define VIN_EP			vin3ep
+#undef CAM_ENABLED
+#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
+//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi"
+
+#ifdef CAM_ENABLED
+&vin3 {
+	status = "okay";
+	pinctrl-0 = <&vin3_pins>;
+	pinctrl-names = "default";
+
+	port {
+		vin3ep: endpoint {
+			remote-endpoint = <&cam3ep>;
+			bus-width = <8>;
+			bus-type = <MEDIA_BUS_TYPE_BT656>;
+		};
+	};
+};
+#endif /* CAM_ENABLED */
+
+#undef CAM_PARENT_I2C
+#undef MCLK_CAM
+#undef CAM_EP
+#undef VIN_EP
diff --git a/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
new file mode 100644
index 000000000000..c73160df619d
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This include file ties a VIN interface with a single ov5640 sensor on
+ * the iWave-RZ/G1H Qseven board development platform connected with the
+ * camera daughter board.
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/media/video-interfaces.h>
+
+#define CAM_ENABLED	1
+
+&CAM_PARENT_I2C {
+	status = "okay";
+
+	ov5640@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		clocks = <&MCLK_CAM>;
+		clock-names = "xclk";
+		AVDD-supply = <&reg_2p8v>;
+		DOVDD-supply = <&reg_2p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		status = "okay";
+
+		port {
+			CAM_EP: endpoint {
+				bus-width = <8>;
+				data-shift = <2>;
+				bus-type = <MEDIA_BUS_TYPE_BT656>;
+				pclk-sample = <1>;
+				remote-endpoint = <&VIN_EP>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi
new file mode 100644
index 000000000000..a7f5cfec64b8
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This include file ties a VIN interface with a single ov7725 sensor on
+ * the iWave-RZ/G1H Qseven board development platform connected with the
+ * camera daughter board.
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/media/video-interfaces.h>
+
+#define CAM_ENABLED	1
+
+&CAM_PARENT_I2C {
+	status = "okay";
+
+	ov7725@21 {
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		clocks = <&MCLK_CAM>;
+		status = "okay";
+
+		port {
+			CAM_EP: endpoint {
+				bus-width = <8>;
+				bus-type = <MEDIA_BUS_TYPE_BT656>;
+				remote-endpoint = <&VIN_EP>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7.dts b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7.dts
new file mode 100644
index 000000000000..64102b664055
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r8a7742-iwg21d-q7.dts
@@ -0,0 +1,445 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the iWave-RZ/G1H Qseven board
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+/*
+ * SSI-SGTL5000
+ *
+ * This command is required when Playback/Capture
+ *
+ *      amixer set "DVC Out" 100%
+ *      amixer set "DVC In" 100%
+ *
+ * You can use Mute
+ *
+ *      amixer set "DVC Out Mute" on
+ *      amixer set "DVC In Mute" on
+ *
+ * You can use Volume Ramp
+ *
+ *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
+ *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
+ *      amixer set "DVC Out Ramp" on
+ *      aplay xxx.wav &
+ *      amixer set "DVC Out"  80%  // Volume Down
+ *      amixer set "DVC Out" 100%  // Volume Up
+ */
+
+/dts-v1/;
+#include "r8a7742-iwg21m.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "iWave Systems RainboW-G21D-Qseven board based on RZ/G1H";
+	compatible = "iwave,g21d", "iwave,g21m", "renesas,r8a7742";
+
+	aliases {
+		serial2 = &scifa2;
+		serial4 = &scifb2;
+		ethernet0 = &avb;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel root=/dev/mmcblk0p1 rw rootwait";
+		stdout-path = "serial2:115200n8";
+	};
+
+	audio_clock: audio_clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	lcd_backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&tpu 2 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		pinctrl-0 = <&backlight_pins>;
+		pinctrl-names = "default";
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		sdhi2_led {
+			label = "sdio-led";
+			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+		};
+	};
+
+	lvds-receiver {
+		compatible = "ti,ds90cf384a", "lvds-decoder";
+		power-supply = <&vcc_3v3_tft1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				lvds_receiver_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				lvds_receiver_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0dh6";
+		backlight = <&lcd_backlight>;
+		power-supply = <&vcc_3v3_tft1>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds_receiver_out>;
+			};
+		};
+	};
+
+	reg_1p5v: 1p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	rsnd_sgtl5000: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&sndcodec>;
+		simple-audio-card,frame-master = <&sndcodec>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+		};
+	};
+
+	vcc_3v3_tft1: regulator-panel {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vcc-3v3-tft1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		startup-delay-us = <500>;
+		gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	vcc_sdhi2: regulator-vcc-sdhi2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI2 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	};
+
+	vccq_sdhi2: regulator-vccq-sdhi2 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI2 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&phy3>;
+	phy-mode = "gmii";
+	renesas,no-ether-link;
+	status = "okay";
+
+	phy3: ethernet-phy@3 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <3>;
+		micrel,led-mode = <1>;
+	};
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
+		reg = <0x0a>;
+		clocks = <&audio_clock>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		VDDD-supply = <&reg_1p5v>;
+	};
+
+	touch: touchpanel@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		/* GP1_29 is also shared with audio codec reset pin */
+		reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&vcc_3v3_tft1>;
+	};
+};
+
+&can1 {
+	pinctrl-0 = <&can1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&cmt0 {
+	status = "okay";
+};
+
+&du {
+	status = "okay";
+};
+
+&gpio0 {
+	touch-interrupt-hog {
+		gpio-hog;
+		gpios = <24 GPIO_ACTIVE_LOW>;
+		input;
+	};
+};
+
+&gpio1 {
+	can-trx-en-hog {
+		gpio-hog;
+		gpios = <28 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can-trx-en-gpio";
+	};
+};
+
+&hsusb {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&lvds0 {
+	status = "okay";
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_receiver_in>;
+			};
+		};
+	};
+};
+
+&msiof0 {
+	pinctrl-0 = <&msiof0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+
+	flash1: flash@0 {
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "user";
+				reg = <0x00000000 0x00200000>;
+			};
+		};
+	};
+};
+
+&pci0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+	/* Disable hsusb to enable USB2.0 host mode support on J2 */
+	/* status = "okay"; */
+};
+
+&pci1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&pci2 {
+	/* Disable xhci to enable USB2.0 host mode support on J23 bottom port */
+	/* status = "okay"; */
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pciec {
+	/* SW2[6] determines which connector is activated
+	 * ON = PCIe X4 (connector-J7)
+	 * OFF = mini-PCIe (connector-J26)
+	 */
+	status = "okay";
+};
+
+&pfc {
+	avb_pins: avb {
+		groups = "avb_mdio", "avb_gmii";
+		function = "avb";
+	};
+
+	backlight_pins: backlight {
+		groups = "tpu0_to2";
+		function = "tpu0";
+	};
+
+	can1_pins: can1 {
+		groups = "can1_data_b";
+		function = "can1";
+	};
+
+	i2c2_pins: i2c2 {
+		groups = "i2c2_b";
+		function = "i2c2";
+	};
+
+	msiof0_pins: msiof0 {
+		groups = "msiof0_clk", "msiof0_sync", "msiof0_tx", "msiof0_rx";
+		function = "msiof0";
+	};
+
+	scifa2_pins: scifa2 {
+		groups = "scifa2_data_c";
+		function = "scifa2";
+	};
+
+	scifb2_pins: scifb2 {
+		groups = "scifb2_data", "scifb2_ctrl";
+		function = "scifb2";
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "sdhi2_data4", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data4", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data";
+		function = "ssi";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		groups = "usb1_pwen";
+		function = "usb1";
+	};
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi4>, <&src4>, <&dvc1>;
+			capture = <&ssi3>, <&src3>, <&dvc0>;
+		};
+	};
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scifa2 {
+	pinctrl-0 = <&scifa2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&scifb2 {
+	pinctrl-0 = <&scifb2_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&sdhi2 {
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi2>;
+	vqmmc-supply = <&vccq_sdhi2>;
+	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&ssi4 {
+	shared-pin;
+};
+
+&tpu {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/renesas/r8a7742-iwg21m.dtsi b/arch/arm/boot/dts/renesas/r8a7742-iwg21m.dtsi
new file mode 100644
index 000000000000..b281a4d164b0
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r8a7742-iwg21m.dtsi
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the iWave RZ/G1H Qseven SOM
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+#include "r8a7742.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "iwave,g21m", "renesas,r8a7742";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x40000000>;
+	};
+
+	memory@200000000 {
+		device_type = "memory";
+		reg = <2 0x00000000 0 0x40000000>;
+	};
+
+	reg_3p3v: 3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <20000000>;
+};
+
+&gpio0 {
+	/* GP0_18 set low to select QSPI. Doing so will disable VIN2 */
+	qspi-en-hog {
+		gpio-hog;
+		gpios = <18 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "QSPI_EN";
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rtc@68 {
+		compatible = "ti,bq32000";
+		reg = <0x68>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&mmcif1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&reg_3p3v>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pfc {
+	i2c0_pins: i2c0 {
+		groups = "i2c0";
+		function = "i2c0";
+	};
+
+	mmc1_pins: mmc1 {
+		groups = "mmc1_data4", "mmc1_ctrl";
+		function = "mmc1";
+	};
+
+	qspi_pins: qspi {
+		groups = "qspi_ctrl", "qspi_data2";
+		function = "qspi";
+	};
+};
+
+&qspi {
+	pinctrl-0 = <&qspi_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bootloader";
+				reg = <0x00000000 0x000c0000>;
+				read-only;
+			};
+			partition@c0000 {
+				label = "env";
+				reg = <0x000c0000 0x00002000>;
+			};
+			partition@c2000 {
+				label = "user";
+				reg = <0x000c2000 0x0013e000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/renesas/r8a7742.dtsi b/arch/arm/boot/dts/renesas/r8a7742.dtsi
new file mode 100644
index 000000000000..16d146db824a
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r8a7742.dtsi
@@ -0,0 +1,1891 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the r8a7742 SoC
+ *
+ * Copyright (C) 2020 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/clock/r8a7742-cpg-mssr.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7742-sysc.h>
+
+/ {
+	compatible = "renesas,r8a7742";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	/*
+	 * The external audio clocks are configured as 0 Hz fixed frequency
+	 * clocks by default.
+	 * Boards that provide audio clocks should override them.
+	 */
+	audio_clk_a: audio_clk_a {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+	audio_clk_b: audio_clk_b {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+	audio_clk_c: audio_clk_c {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	/* External CAN clock */
+	can_clk: can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+			clock-frequency = <1400000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z>;
+			power-domains = <&sysc R8A7742_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
+			next-level-cache = <&L2_CA15>;
+			capacity-dmips-mhz = <1024>;
+			voltage-tolerance = <1>; /* 1% */
+			clock-latency = <300000>; /* 300 us */
+
+			/* kHz - uV - OPPs unknown yet */
+			operating-points = <1400000 1000000>,
+					   <1225000 1000000>,
+					   <1050000 1000000>,
+					   < 875000 1000000>,
+					   < 700000 1000000>,
+					   < 350000 1000000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			clock-frequency = <1400000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z>;
+			power-domains = <&sysc R8A7742_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
+			next-level-cache = <&L2_CA15>;
+			capacity-dmips-mhz = <1024>;
+			voltage-tolerance = <1>; /* 1% */
+			clock-latency = <300000>; /* 300 us */
+
+			/* kHz - uV - OPPs unknown yet */
+			operating-points = <1400000 1000000>,
+					   <1225000 1000000>,
+					   <1050000 1000000>,
+					   < 875000 1000000>,
+					   < 700000 1000000>,
+					   < 350000 1000000>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <2>;
+			clock-frequency = <1400000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z>;
+			power-domains = <&sysc R8A7742_PD_CA15_CPU2>;
+			enable-method = "renesas,apmu";
+			next-level-cache = <&L2_CA15>;
+			capacity-dmips-mhz = <1024>;
+			voltage-tolerance = <1>; /* 1% */
+			clock-latency = <300000>; /* 300 us */
+
+			/* kHz - uV - OPPs unknown yet */
+			operating-points = <1400000 1000000>,
+					   <1225000 1000000>,
+					   <1050000 1000000>,
+					   < 875000 1000000>,
+					   < 700000 1000000>,
+					   < 350000 1000000>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <3>;
+			clock-frequency = <1400000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z>;
+			power-domains = <&sysc R8A7742_PD_CA15_CPU3>;
+			enable-method = "renesas,apmu";
+			next-level-cache = <&L2_CA15>;
+			capacity-dmips-mhz = <1024>;
+			voltage-tolerance = <1>; /* 1% */
+			clock-latency = <300000>; /* 300 us */
+
+			/* kHz - uV - OPPs unknown yet */
+			operating-points = <1400000 1000000>,
+					   <1225000 1000000>,
+					   <1050000 1000000>,
+					   < 875000 1000000>,
+					   < 700000 1000000>,
+					   < 350000 1000000>;
+		};
+
+		cpu4: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x100>;
+			clock-frequency = <780000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z2>;
+			power-domains = <&sysc R8A7742_PD_CA7_CPU0>;
+			next-level-cache = <&L2_CA7>;
+		};
+
+		cpu5: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x101>;
+			clock-frequency = <780000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z2>;
+			power-domains = <&sysc R8A7742_PD_CA7_CPU1>;
+			next-level-cache = <&L2_CA7>;
+		};
+
+		cpu6: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x102>;
+			clock-frequency = <780000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z2>;
+			power-domains = <&sysc R8A7742_PD_CA7_CPU2>;
+			next-level-cache = <&L2_CA7>;
+		};
+
+		cpu7: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x103>;
+			clock-frequency = <780000000>;
+			clocks = <&cpg CPG_CORE R8A7742_CLK_Z2>;
+			power-domains = <&sysc R8A7742_PD_CA7_CPU3>;
+			next-level-cache = <&L2_CA7>;
+		};
+
+		L2_CA15: cache-controller-0 {
+			compatible = "cache";
+			power-domains = <&sysc R8A7742_PD_CA15_SCU>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		L2_CA7: cache-controller-1 {
+			compatible = "cache";
+			power-domains = <&sysc R8A7742_PD_CA7_SCU>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	/* External root clock */
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+
+	/* External PCIe clock - can be overridden by the board */
+	pcie_bus_clk: pcie_bus {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	pmu-0 {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	pmu-1 {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts-extended = <&gic GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+	};
+
+	/* External SCIF clock */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board. */
+		clock-frequency = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		rwdt: watchdog@e6020000 {
+			compatible = "renesas,r8a7742-wdt",
+				     "renesas,rcar-gen2-wdt";
+			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 402>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 402>;
+			status = "disabled";
+		};
+
+		gpio0: gpio@e6050000 {
+			compatible = "renesas,gpio-r8a7742",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6050000 0 0x50>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 0 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 912>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 912>;
+		};
+
+		gpio1: gpio@e6051000 {
+			compatible = "renesas,gpio-r8a7742",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6051000 0 0x50>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 32 30>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 911>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 911>;
+		};
+
+		gpio2: gpio@e6052000 {
+			compatible = "renesas,gpio-r8a7742",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6052000 0 0x50>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 64 30>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 910>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 910>;
+		};
+
+		gpio3: gpio@e6053000 {
+			compatible = "renesas,gpio-r8a7742",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6053000 0 0x50>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 96 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 909>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 909>;
+		};
+
+		gpio4: gpio@e6054000 {
+			compatible = "renesas,gpio-r8a7742",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6054000 0 0x50>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 128 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 908>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 908>;
+		};
+
+		gpio5: gpio@e6055000 {
+			compatible = "renesas,gpio-r8a7742",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6055000 0 0x50>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 160 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 907>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 907>;
+		};
+
+		pfc: pinctrl@e6060000 {
+			compatible = "renesas,pfc-r8a7742";
+			reg = <0 0xe6060000 0 0x250>;
+		};
+
+		tpu: pwm@e60f0000 {
+			compatible = "renesas,tpu-r8a7742", "renesas,tpu";
+			reg = <0 0xe60f0000 0 0x148>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 304>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 304>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		cpg: clock-controller@e6150000 {
+			compatible = "renesas,r8a7742-cpg-mssr";
+			reg = <0 0xe6150000 0 0x1000>;
+			clocks = <&extal_clk>, <&usb_extal_clk>;
+			clock-names = "extal", "usb_extal";
+			#clock-cells = <2>;
+			#power-domain-cells = <0>;
+			#reset-cells = <1>;
+		};
+
+		apmu@e6151000 {
+			compatible = "renesas,r8a7742-apmu", "renesas,apmu";
+			reg = <0 0xe6151000 0 0x188>;
+			cpus = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+		};
+
+		apmu@e6152000 {
+			compatible = "renesas,r8a7742-apmu", "renesas,apmu";
+			reg = <0 0xe6152000 0 0x188>;
+			cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+		};
+
+		rst: reset-controller@e6160000 {
+			compatible = "renesas,r8a7742-rst";
+			reg = <0 0xe6160000 0 0x0100>;
+		};
+
+		sysc: system-controller@e6180000 {
+			compatible = "renesas,r8a7742-sysc";
+			reg = <0 0xe6180000 0 0x0200>;
+			#power-domain-cells = <1>;
+		};
+
+		irqc: interrupt-controller@e61c0000 {
+			compatible = "renesas,irqc-r8a7742", "renesas,irqc";
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <0 0xe61c0000 0 0x200>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 407>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 407>;
+		};
+
+		thermal: thermal@e61f0000 {
+			compatible = "renesas,thermal-r8a7742",
+				     "renesas,rcar-gen2-thermal";
+			reg = <0 0xe61f0000 0 0x10>, <0 0xe61f0100 0 0x38>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 522>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 522>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		ipmmu_sy0: iommu@e6280000 {
+			compatible = "renesas,ipmmu-r8a7742",
+				     "renesas,ipmmu-vmsa";
+			reg = <0 0xe6280000 0 0x1000>;
+			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_sy1: iommu@e6290000 {
+			compatible = "renesas,ipmmu-r8a7742",
+				     "renesas,ipmmu-vmsa";
+			reg = <0 0xe6290000 0 0x1000>;
+			interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ds: iommu@e6740000 {
+			compatible = "renesas,ipmmu-r8a7742",
+				     "renesas,ipmmu-vmsa";
+			reg = <0 0xe6740000 0 0x1000>;
+			interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_mp: iommu@ec680000 {
+			compatible = "renesas,ipmmu-r8a7742",
+				     "renesas,ipmmu-vmsa";
+			reg = <0 0xec680000 0 0x1000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_mx: iommu@fe951000 {
+			compatible = "renesas,ipmmu-r8a7742",
+				     "renesas,ipmmu-vmsa";
+			reg = <0 0xfe951000 0 0x1000>;
+			interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		icram0: sram@e63a0000 {
+			compatible = "mmio-sram";
+			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
+		};
+
+		icram1: sram@e63c0000 {
+			compatible = "mmio-sram";
+			reg = <0 0xe63c0000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63c0000 0x1000>;
+
+			smp-sram@0 {
+				compatible = "renesas,smp-sram";
+				reg = <0 0x100>;
+			};
+		};
+
+		icram2: sram@e6300000 {
+			compatible = "mmio-sram";
+			reg = <0 0xe6300000 0 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe6300000 0x40000>;
+		};
+
+		i2c0: i2c@e6508000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7742",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6508000 0 0x40>;
+			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 931>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 931>;
+			i2c-scl-internal-delay-ns = <110>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@e6518000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7742",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6518000 0 0x40>;
+			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 930>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 930>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@e6530000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7742",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6530000 0 0x40>;
+			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 929>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 929>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@e6540000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7742",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6540000 0 0x40>;
+			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 928>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 928>;
+			i2c-scl-internal-delay-ns = <110>;
+			status = "disabled";
+		};
+
+		iic0: i2c@e6500000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7742",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe6500000 0 0x425>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 318>;
+			dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+			       <&dmac1 0x61>, <&dmac1 0x62>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 318>;
+			status = "disabled";
+		};
+
+		iic1: i2c@e6510000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7742",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe6510000 0 0x425>;
+			interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 323>;
+			dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+			       <&dmac1 0x65>, <&dmac1 0x66>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 323>;
+			status = "disabled";
+		};
+
+		iic2: i2c@e6520000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7742",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe6520000 0 0x425>;
+			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 300>;
+			dmas = <&dmac0 0x69>, <&dmac0 0x6a>,
+			       <&dmac1 0x69>, <&dmac1 0x6a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 300>;
+			status = "disabled";
+		};
+
+		iic3: i2c@e60b0000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7742",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe60b0000 0 0x425>;
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 926>;
+			dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+			       <&dmac1 0x77>, <&dmac1 0x78>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 926>;
+			status = "disabled";
+		};
+
+		hsusb: usb@e6590000 {
+			compatible = "renesas,usbhs-r8a7742",
+				     "renesas,rcar-gen2-usbhs";
+			reg = <0 0xe6590000 0 0x100>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 704>;
+			dmas = <&usb_dmac0 0>, <&usb_dmac0 1>,
+			       <&usb_dmac1 0>, <&usb_dmac1 1>;
+			dma-names = "ch0", "ch1", "ch2", "ch3";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 704>;
+			renesas,buswait = <4>;
+			phys = <&usb0 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		usbphy: usb-phy-controller@e6590100 {
+			compatible = "renesas,usb-phy-r8a7742",
+				     "renesas,rcar-gen2-usb-phy";
+			reg = <0 0xe6590100 0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&cpg CPG_MOD 704>;
+			clock-names = "usbhs";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 704>;
+			status = "disabled";
+
+			usb0: usb-phy@0 {
+				reg = <0>;
+				#phy-cells = <1>;
+			};
+			usb2: usb-phy@2 {
+				reg = <2>;
+				#phy-cells = <1>;
+			};
+		};
+
+		usb_dmac0: dma-controller@e65a0000 {
+			compatible = "renesas,r8a7742-usb-dmac",
+				     "renesas,usb-dmac";
+			reg = <0 0xe65a0000 0 0x100>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1";
+			clocks = <&cpg CPG_MOD 330>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 330>;
+			#dma-cells = <1>;
+			dma-channels = <2>;
+		};
+
+		usb_dmac1: dma-controller@e65b0000 {
+			compatible = "renesas,r8a7742-usb-dmac",
+				     "renesas,usb-dmac";
+			reg = <0 0xe65b0000 0 0x100>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1";
+			clocks = <&cpg CPG_MOD 331>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 331>;
+			#dma-cells = <1>;
+			dma-channels = <2>;
+		};
+
+		dmac0: dma-controller@e6700000 {
+			compatible = "renesas,dmac-r8a7742",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6700000 0 0x20000>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14";
+			clocks = <&cpg CPG_MOD 219>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 219>;
+			#dma-cells = <1>;
+			dma-channels = <15>;
+		};
+
+		dmac1: dma-controller@e6720000 {
+			compatible = "renesas,dmac-r8a7742",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6720000 0 0x20000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14";
+			clocks = <&cpg CPG_MOD 218>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 218>;
+			#dma-cells = <1>;
+			dma-channels = <15>;
+		};
+
+		avb: ethernet@e6800000 {
+			compatible = "renesas,etheravb-r8a7742",
+				     "renesas,etheravb-rcar-gen2";
+			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
+			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 812>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		qspi: spi@e6b10000 {
+			compatible = "renesas,qspi-r8a7742", "renesas,qspi";
+			reg = <0 0xe6b10000 0 0x2c>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+			       <&dmac1 0x17>, <&dmac1 0x18>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		scifa0: serial@e6c40000 {
+			compatible = "renesas,scifa-r8a7742",
+				     "renesas,rcar-gen2-scifa", "renesas,scifa";
+			reg = <0 0xe6c40000 0 0x40>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 204>;
+			clock-names = "fck";
+			dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+			       <&dmac1 0x21>, <&dmac1 0x22>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 204>;
+			status = "disabled";
+		};
+
+		scifa1: serial@e6c50000 {
+			compatible = "renesas,scifa-r8a7742",
+				     "renesas,rcar-gen2-scifa", "renesas,scifa";
+			reg = <0 0xe6c50000 0 0x40>;
+			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 203>;
+			clock-names = "fck";
+			dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+			       <&dmac1 0x25>, <&dmac1 0x26>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 203>;
+			status = "disabled";
+		};
+
+		scifa2: serial@e6c60000 {
+			compatible = "renesas,scifa-r8a7742",
+				     "renesas,rcar-gen2-scifa", "renesas,scifa";
+			reg = <0 0xe6c60000 0 0x40>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 202>;
+			clock-names = "fck";
+			dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+			       <&dmac1 0x27>, <&dmac1 0x28>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 202>;
+			status = "disabled";
+		};
+
+		scifb0: serial@e6c20000 {
+			compatible = "renesas,scifb-r8a7742",
+				     "renesas,rcar-gen2-scifb", "renesas,scifb";
+			reg = <0 0xe6c20000 0 0x100>;
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 206>;
+			clock-names = "fck";
+			dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+			       <&dmac1 0x3d>, <&dmac1 0x3e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 206>;
+			status = "disabled";
+		};
+
+		scifb1: serial@e6c30000 {
+			compatible = "renesas,scifb-r8a7742",
+				     "renesas,rcar-gen2-scifb", "renesas,scifb";
+			reg = <0 0xe6c30000 0 0x100>;
+			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 207>;
+			clock-names = "fck";
+			dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+			       <&dmac1 0x19>, <&dmac1 0x1a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 207>;
+			status = "disabled";
+		};
+
+		scifb2: serial@e6ce0000 {
+			compatible = "renesas,scifb-r8a7742",
+				     "renesas,rcar-gen2-scifb", "renesas,scifb";
+			reg = <0 0xe6ce0000 0 0x100>;
+			interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 216>;
+			clock-names = "fck";
+			dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+			       <&dmac1 0x1d>, <&dmac1 0x1e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 216>;
+			status = "disabled";
+		};
+
+		scif0: serial@e6e60000 {
+			compatible = "renesas,scif-r8a7742",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e60000 0 0x40>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 721>,
+				 <&cpg CPG_CORE R8A7742_CLK_ZS>, <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+			       <&dmac1 0x29>, <&dmac1 0x2a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 721>;
+			status = "disabled";
+		};
+
+		scif1: serial@e6e68000 {
+			compatible = "renesas,scif-r8a7742",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e68000 0 0x40>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 720>,
+				 <&cpg CPG_CORE R8A7742_CLK_ZS>, <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+			       <&dmac1 0x2d>, <&dmac1 0x2e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 720>;
+			status = "disabled";
+		};
+
+		scif2: serial@e6e56000 {
+			compatible = "renesas,scif-r8a7742",
+				     "renesas,rcar-gen2-scif", "renesas,scif";
+			reg = <0 0xe6e56000 0 0x40>;
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 310>,
+				 <&cpg CPG_CORE R8A7742_CLK_ZS>, <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+			       <&dmac1 0x2b>, <&dmac1 0x2c>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 310>;
+			status = "disabled";
+		};
+
+		hscif0: serial@e62c0000 {
+			compatible = "renesas,hscif-r8a7742",
+				     "renesas,rcar-gen2-hscif", "renesas,hscif";
+			reg = <0 0xe62c0000 0 0x60>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 717>,
+				 <&cpg CPG_CORE R8A7742_CLK_ZS>, <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+			       <&dmac1 0x39>, <&dmac1 0x3a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 717>;
+			status = "disabled";
+		};
+
+		hscif1: serial@e62c8000 {
+			compatible = "renesas,hscif-r8a7742",
+				     "renesas,rcar-gen2-hscif", "renesas,hscif";
+			reg = <0 0xe62c8000 0 0x60>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 716>,
+				 <&cpg CPG_CORE R8A7742_CLK_ZS>, <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+			       <&dmac1 0x4d>, <&dmac1 0x4e>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 716>;
+			status = "disabled";
+		};
+
+		msiof0: spi@e6e20000 {
+			compatible = "renesas,msiof-r8a7742",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e20000 0 0x0064>;
+			interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 0>;
+			dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+			       <&dmac1 0x51>, <&dmac1 0x52>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof1: spi@e6e10000 {
+			compatible = "renesas,msiof-r8a7742",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e10000 0 0x0064>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 208>;
+			dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+			       <&dmac1 0x55>, <&dmac1 0x56>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 208>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof2: spi@e6e00000 {
+			compatible = "renesas,msiof-r8a7742",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e00000 0 0x0064>;
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 205>;
+			dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+			       <&dmac1 0x41>, <&dmac1 0x42>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 205>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof3: spi@e6c90000 {
+			compatible = "renesas,msiof-r8a7742",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6c90000 0 0x0064>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 215>;
+			dmas = <&dmac0 0x45>, <&dmac0 0x46>,
+			       <&dmac1 0x45>, <&dmac1 0x46>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 215>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		can0: can@e6e80000 {
+			compatible = "renesas,can-r8a7742",
+				     "renesas,rcar-gen2-can";
+			reg = <0 0xe6e80000 0 0x1000>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 916>,
+				 <&cpg CPG_CORE R8A7742_CLK_RCAN>, <&can_clk>;
+			clock-names = "clkp1", "clkp2", "can_clk";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 916>;
+			status = "disabled";
+		};
+
+		can1: can@e6e88000 {
+			compatible = "renesas,can-r8a7742",
+				     "renesas,rcar-gen2-can";
+			reg = <0 0xe6e88000 0 0x1000>;
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>,
+				 <&cpg CPG_CORE R8A7742_CLK_RCAN>, <&can_clk>;
+			clock-names = "clkp1", "clkp2", "can_clk";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			status = "disabled";
+		};
+
+		pwm0: pwm@e6e30000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e30000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@e6e31000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e31000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm2: pwm@e6e32000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e32000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm3: pwm@e6e33000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e33000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm4: pwm@e6e34000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e34000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm5: pwm@e6e35000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e35000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm6: pwm@e6e36000 {
+			compatible = "renesas,pwm-r8a7742", "renesas,pwm-rcar";
+			reg = <0 0xe6e36000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		vin0: video@e6ef0000 {
+			compatible = "renesas,vin-r8a7742",
+				     "renesas,rcar-gen2-vin";
+			reg = <0 0xe6ef0000 0 0x1000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 811>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 811>;
+			status = "disabled";
+		};
+
+		vin1: video@e6ef1000 {
+			compatible = "renesas,vin-r8a7742",
+				     "renesas,rcar-gen2-vin";
+			reg = <0 0xe6ef1000 0 0x1000>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 810>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 810>;
+			status = "disabled";
+		};
+
+		vin2: video@e6ef2000 {
+			compatible = "renesas,vin-r8a7742",
+				     "renesas,rcar-gen2-vin";
+			reg = <0 0xe6ef2000 0 0x1000>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 809>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 809>;
+			status = "disabled";
+		};
+
+		vin3: video@e6ef3000 {
+			compatible = "renesas,vin-r8a7742",
+				     "renesas,rcar-gen2-vin";
+			reg = <0 0xe6ef3000 0 0x1000>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 808>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 808>;
+			status = "disabled";
+		};
+
+		rcar_sound: sound@ec500000 {
+			/*
+			 * #sound-dai-cells is required if simple-card
+			 *
+			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
+			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
+			 */
+			compatible = "renesas,rcar_sound-r8a7742",
+				     "renesas,rcar_sound-gen2";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec740000 0 0x200>;  /* Audio DMAC peri peri*/
+			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
+
+			clocks = <&cpg CPG_MOD 1005>,
+				 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+				 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+				 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+				 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+				 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+				 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+				 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+				 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+				 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+				 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+				 <&cpg CPG_MOD 1021>, <&cpg CPG_MOD 1020>,
+				 <&cpg CPG_MOD 1021>, <&cpg CPG_MOD 1020>,
+				 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+				 <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>,
+				 <&cpg CPG_CORE R8A7742_CLK_M2>;
+			clock-names = "ssi-all",
+				      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+				      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+				      "ssi.1", "ssi.0",
+				      "src.9", "src.8", "src.7", "src.6",
+				      "src.5", "src.4", "src.3", "src.2",
+				      "src.1", "src.0",
+				      "ctu.0", "ctu.1",
+				      "mix.0", "mix.1",
+				      "dvc.0", "dvc.1",
+				      "clk_a", "clk_b", "clk_c", "clk_i";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 1005>,
+				 <&cpg 1006>, <&cpg 1007>,
+				 <&cpg 1008>, <&cpg 1009>,
+				 <&cpg 1010>, <&cpg 1011>,
+				 <&cpg 1012>, <&cpg 1013>,
+				 <&cpg 1014>, <&cpg 1015>;
+			reset-names = "ssi-all",
+				      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+				      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+				      "ssi.1", "ssi.0";
+
+			status = "disabled";
+
+			rcar_sound,dvc {
+				dvc0: dvc-0 {
+					dmas = <&audma1 0xbc>;
+					dma-names = "tx";
+				};
+				dvc1: dvc-1 {
+					dmas = <&audma1 0xbe>;
+					dma-names = "tx";
+				};
+			};
+
+			rcar_sound,mix {
+				mix0: mix-0 { };
+				mix1: mix-1 { };
+			};
+
+			rcar_sound,ctu {
+				ctu00: ctu-0 { };
+				ctu01: ctu-1 { };
+				ctu02: ctu-2 { };
+				ctu03: ctu-3 { };
+				ctu10: ctu-4 { };
+				ctu11: ctu-5 { };
+				ctu12: ctu-6 { };
+				ctu13: ctu-7 { };
+			};
+
+			rcar_sound,src {
+				src0: src-0 {
+					interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x85>, <&audma1 0x9a>;
+					dma-names = "rx", "tx";
+				};
+				src1: src-1 {
+					interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x87>, <&audma1 0x9c>;
+					dma-names = "rx", "tx";
+				};
+				src2: src-2 {
+					interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x89>, <&audma1 0x9e>;
+					dma-names = "rx", "tx";
+				};
+				src3: src-3 {
+					interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8b>, <&audma1 0xa0>;
+					dma-names = "rx", "tx";
+				};
+				src4: src-4 {
+					interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8d>, <&audma1 0xb0>;
+					dma-names = "rx", "tx";
+				};
+				src5: src-5 {
+					interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8f>, <&audma1 0xb2>;
+					dma-names = "rx", "tx";
+				};
+				src6: src-6 {
+					interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x91>, <&audma1 0xb4>;
+					dma-names = "rx", "tx";
+				};
+				src7: src-7 {
+					interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x93>, <&audma1 0xb6>;
+					dma-names = "rx", "tx";
+				};
+				src8: src-8 {
+					interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x95>, <&audma1 0xb8>;
+					dma-names = "rx", "tx";
+				};
+				src9: src-9 {
+					interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x97>, <&audma1 0xba>;
+					dma-names = "rx", "tx";
+				};
+			};
+
+			rcar_sound,ssi {
+				ssi0: ssi-0 {
+					interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x01>, <&audma1 0x02>,
+					       <&audma0 0x15>, <&audma1 0x16>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi1: ssi-1 {
+					interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x03>, <&audma1 0x04>,
+					       <&audma0 0x49>, <&audma1 0x4a>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi2: ssi-2 {
+					interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x05>, <&audma1 0x06>,
+					       <&audma0 0x63>, <&audma1 0x64>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi3: ssi-3 {
+					interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x07>, <&audma1 0x08>,
+					       <&audma0 0x6f>, <&audma1 0x70>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi4: ssi-4 {
+					interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x09>, <&audma1 0x0a>,
+					       <&audma0 0x71>, <&audma1 0x72>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi5: ssi-5 {
+					interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x0b>, <&audma1 0x0c>,
+					       <&audma0 0x73>, <&audma1 0x74>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi6: ssi-6 {
+					interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x0d>, <&audma1 0x0e>,
+					       <&audma0 0x75>, <&audma1 0x76>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi7: ssi-7 {
+					interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x0f>, <&audma1 0x10>,
+					       <&audma0 0x79>, <&audma1 0x7a>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi8: ssi-8 {
+					interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x11>, <&audma1 0x12>,
+					       <&audma0 0x7b>, <&audma1 0x7c>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+				ssi9: ssi-9 {
+					interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x13>, <&audma1 0x14>,
+					       <&audma0 0x7d>, <&audma1 0x7e>;
+					dma-names = "rx", "tx", "rxu", "txu";
+				};
+			};
+		};
+
+		audma0: dma-controller@ec700000 {
+			compatible = "renesas,dmac-r8a7742",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec700000 0 0x10000>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12";
+			clocks = <&cpg CPG_MOD 502>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 502>;
+			#dma-cells = <1>;
+			dma-channels = <13>;
+		};
+
+		audma1: dma-controller@ec720000 {
+			compatible = "renesas,dmac-r8a7742",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec720000 0 0x10000>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12";
+			clocks = <&cpg CPG_MOD 501>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 501>;
+			#dma-cells = <1>;
+			dma-channels = <13>;
+		};
+
+		xhci: usb@ee000000 {
+			compatible = "renesas,xhci-r8a7742",
+				     "renesas,rcar-gen2-xhci";
+			reg = <0 0xee000000 0 0xc00>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 328>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 328>;
+			phys = <&usb2 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		pci0: pci@ee090000 {
+			compatible = "renesas,pci-r8a7742",
+				     "renesas,pci-rcar-gen2";
+			device_type = "pci";
+			reg = <0 0xee090000 0 0xc00>,
+			      <0 0xee080000 0 0x1100>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+
+			bus-range = <0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+
+			usb@1,0 {
+				reg = <0x800 0 0 0 0>;
+				phys = <&usb0 0>;
+				phy-names = "usb";
+			};
+
+			usb@2,0 {
+				reg = <0x1000 0 0 0 0>;
+				phys = <&usb0 0>;
+				phy-names = "usb";
+			};
+		};
+
+		pci1: pci@ee0b0000 {
+			compatible = "renesas,pci-r8a7742",
+				     "renesas,pci-rcar-gen2";
+			device_type = "pci";
+			reg = <0 0xee0b0000 0 0xc00>,
+			      <0 0xee0a0000 0 0x1100>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+
+			bus-range = <1 1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0xee0a0000 0 0xee0a0000 0 0x00010000>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pci2: pci@ee0d0000 {
+			compatible = "renesas,pci-r8a7742",
+				     "renesas,pci-rcar-gen2";
+			device_type = "pci";
+			clocks = <&cpg CPG_MOD 703>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			reg = <0 0xee0d0000 0 0xc00>,
+			      <0 0xee0c0000 0 0x1100>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			bus-range = <2 2>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+
+			usb@1,0 {
+				reg = <0x20800 0 0 0 0>;
+				phys = <&usb2 0>;
+				phy-names = "usb";
+			};
+
+			usb@2,0 {
+				reg = <0x21000 0 0 0 0>;
+				phys = <&usb2 0>;
+				phy-names = "usb";
+			};
+		};
+
+		sdhi0: mmc@ee100000 {
+			compatible = "renesas,sdhi-r8a7742",
+				     "renesas,rcar-gen2-sdhi";
+			reg = <0 0xee100000 0 0x328>;
+			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 314>;
+			dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+			       <&dmac1 0xcd>, <&dmac1 0xce>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <195000000>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 314>;
+			status = "disabled";
+		};
+
+		sdhi1: mmc@ee120000 {
+			compatible = "renesas,sdhi-r8a7742",
+				     "renesas,rcar-gen2-sdhi";
+			reg = <0 0xee120000 0 0x328>;
+			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 313>;
+			dmas = <&dmac0 0xc9>, <&dmac0 0xca>,
+			       <&dmac1 0xc9>, <&dmac1 0xca>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <195000000>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 313>;
+			status = "disabled";
+		};
+
+		sdhi2: mmc@ee140000 {
+			compatible = "renesas,sdhi-r8a7742",
+				     "renesas,rcar-gen2-sdhi";
+			reg = <0 0xee140000 0 0x100>;
+			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 312>;
+			dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+			       <&dmac1 0xc1>, <&dmac1 0xc2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <97500000>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 312>;
+			status = "disabled";
+		};
+
+		sdhi3: mmc@ee160000 {
+			compatible = "renesas,sdhi-r8a7742",
+				     "renesas,rcar-gen2-sdhi";
+			reg = <0 0xee160000 0 0x100>;
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 311>;
+			dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+			       <&dmac1 0xd3>, <&dmac1 0xd4>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <97500000>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 311>;
+			status = "disabled";
+		};
+
+		mmcif0: mmc@ee200000 {
+			compatible = "renesas,mmcif-r8a7742",
+				     "renesas,sh-mmcif";
+			reg = <0 0xee200000 0 0x80>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 315>;
+			dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+			       <&dmac1 0xd1>, <&dmac1 0xd2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 315>;
+			reg-io-width = <4>;
+			status = "disabled";
+			max-frequency = <97500000>;
+		};
+
+		mmcif1: mmc@ee220000 {
+			compatible = "renesas,mmcif-r8a7742",
+				     "renesas,sh-mmcif";
+			reg = <0 0xee220000 0 0x80>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 305>;
+			dmas = <&dmac0 0xe1>, <&dmac0 0xe2>,
+			       <&dmac1 0xe1>, <&dmac1 0xe2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 305>;
+			reg-io-width = <4>;
+			status = "disabled";
+			max-frequency = <97500000>;
+		};
+
+		sata0: sata@ee300000 {
+			compatible = "renesas,sata-r8a7742",
+				     "renesas,rcar-gen2-sata";
+			reg = <0 0xee300000 0 0x200000>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 815>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 815>;
+			status = "disabled";
+		};
+
+		sata1: sata@ee500000 {
+			compatible = "renesas,sata-r8a7742",
+				     "renesas,rcar-gen2-sata";
+			reg = <0 0xee500000 0 0x200000>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 814>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 814>;
+			status = "disabled";
+		};
+
+		ether: ethernet@ee700000 {
+			compatible = "renesas,ether-r8a7742",
+				     "renesas,rcar-gen2-ether";
+			reg = <0 0xee700000 0 0x400>;
+			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 813>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 813>;
+			phy-mode = "rmii";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@f1001000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0 0xf1001000 0 0x1000>, <0 0xf1002000 0 0x2000>,
+			      <0 0xf1004000 0 0x2000>, <0 0xf1006000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&cpg CPG_MOD 408>;
+			clock-names = "clk";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 408>;
+		};
+
+		pciec: pcie@fe000000 {
+			compatible = "renesas,pcie-r8a7742",
+				     "renesas,pcie-rcar-gen2";
+			reg = <0 0xfe000000 0 0x80000>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			bus-range = <0x00 0xff>;
+			device_type = "pci";
+			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000>,
+				 <0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000>,
+				 <0x02000000 0 0x30000000 0 0x30000000 0 0x08000000>,
+				 <0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+			/* Map all possible DDR as inbound ranges */
+			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000>,
+				     <0x43000000 1 0x80000000 1 0x80000000 0 0x80000000>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 319>, <&pcie_bus_clk>;
+			clock-names = "pcie", "pcie_bus";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 319>;
+			status = "disabled";
+		};
+
+		vsp@fe920000 {
+			compatible = "renesas,vsp1";
+			reg = <0 0xfe920000 0 0x8000>;
+			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 130>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 130>;
+		};
+
+		vsp@fe928000 {
+			compatible = "renesas,vsp1";
+			reg = <0 0xfe928000 0 0x8000>;
+			interrupts = <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 131>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 131>;
+		};
+
+		vsp@fe930000 {
+			compatible = "renesas,vsp1";
+			reg = <0 0xfe930000 0 0x8000>;
+			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 128>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 128>;
+		};
+
+		vsp@fe938000 {
+			compatible = "renesas,vsp1";
+			reg = <0 0xfe938000 0 0x8000>;
+			interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 127>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 127>;
+		};
+
+		du: display@feb00000 {
+			compatible = "renesas,du-r8a7742";
+			reg = <0 0xfeb00000 0 0x70000>;
+			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
+				 <&cpg CPG_MOD 722>;
+			clock-names = "du.0", "du.1", "du.2";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					du_out_rgb: endpoint {
+					};
+				};
+				port@1 {
+					reg = <1>;
+					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+				port@2 {
+					reg = <2>;
+					du_out_lvds1: endpoint {
+						remote-endpoint = <&lvds1_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7742-lvds";
+			reg = <0 0xfeb90000 0 0x14>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
+					};
+				};
+			};
+		};
+
+		lvds1: lvds@feb94000 {
+			compatible = "renesas,r8a7742-lvds";
+			reg = <0 0xfeb94000 0 0x14>;
+			clocks = <&cpg CPG_MOD 725>;
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 725>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds1_in: endpoint {
+						remote-endpoint = <&du_out_lvds1>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds1_out: endpoint {
+					};
+				};
+			};
+		};
+
+		prr: chipid@ff000044 {
+			compatible = "renesas,prr";
+			reg = <0 0xff000044 0 4>;
+		};
+
+		cmt0: timer@ffca0000 {
+			compatible = "renesas,r8a7742-cmt0",
+				     "renesas,rcar-gen2-cmt0";
+			reg = <0 0xffca0000 0 0x1004>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 124>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 124>;
+			status = "disabled";
+		};
+
+		cmt1: timer@e6130000 {
+			compatible = "renesas,r8a7742-cmt1",
+				     "renesas,rcar-gen2-cmt1";
+			reg = <0 0xe6130000 0 0x1004>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 329>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7742_PD_ALWAYS_ON>;
+			resets = <&cpg 329>;
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	/* External USB clock - can be overridden by the board */
+	usb_extal_clk: usb_extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/r8a7743-iwg20d-q7-dbcm-ca.dts b/arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dts
index 0d006aea99da..0d006aea99da 100644
--- a/arch/arm/boot/dts/r8a7743-iwg20d-q7-dbcm-ca.dts
+++ b/arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dts
diff --git a/arch/arm/boot/dts/r8a7743-iwg20d-q7.dts b/arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dts
index 498e223a5f93..498e223a5f93 100644
--- a/arch/arm/boot/dts/r8a7743-iwg20d-q7.dts
+++ b/arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dts
diff --git a/arch/arm/boot/dts/r8a7743-iwg20m.dtsi b/arch/arm/boot/dts/renesas/r8a7743-iwg20m.dtsi
index b3fee1d61c87..b3fee1d61c87 100644
--- a/arch/arm/boot/dts/r8a7743-iwg20m.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7743-iwg20m.dtsi
diff --git a/arch/arm/boot/dts/r8a7743-sk-rzg1m.dts b/arch/arm/boot/dts/renesas/r8a7743-sk-rzg1m.dts
index 807e7d0d6b62..ff274bfcb664 100644
--- a/arch/arm/boot/dts/r8a7743-sk-rzg1m.dts
+++ b/arch/arm/boot/dts/renesas/r8a7743-sk-rzg1m.dts
@@ -7,6 +7,7 @@
 
 /dts-v1/;
 #include "r8a7743.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "SK-RZG1M";
@@ -61,7 +62,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -69,9 +70,12 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 	};
 };
diff --git a/arch/arm/boot/dts/r8a7743.dtsi b/arch/arm/boot/dts/renesas/r8a7743.dtsi
index de981d629bdd..2245d19a23bb 100644
--- a/arch/arm/boot/dts/r8a7743.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7743.dtsi
@@ -49,7 +49,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -59,6 +58,7 @@
 			clocks = <&cpg CPG_CORE R8A7743_CLK_Z>;
 			clock-latency = <300000>; /* 300 us */
 			power-domains = <&sysc R8A7743_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 
 			/* kHz - uV - OPPs unknown yet */
@@ -78,6 +78,7 @@
 			clocks = <&cpg CPG_CORE R8A7743_CLK_Z>;
 			clock-latency = <300000>; /* 300 us */
 			power-domains = <&sysc R8A7743_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 
 			/* kHz - uV - OPPs unknown yet */
@@ -139,6 +140,7 @@
 			compatible = "renesas,r8a7743-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -265,7 +267,7 @@
 			resets = <&cpg 904>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7743";
 			reg = <0 0xe6060000 0 0x250>;
 		};
@@ -293,7 +295,7 @@
 		apmu@e6152000 {
 			compatible = "renesas,r8a7743-apmu", "renesas,apmu";
 			reg = <0 0xe6152000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -338,7 +340,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7743",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -348,7 +350,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7743",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -357,7 +359,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7743",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -367,7 +369,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7743",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -376,7 +378,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7743",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -386,7 +388,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_gp: mmu@e62a0000 {
+		ipmmu_gp: iommu@e62a0000 {
 			compatible = "renesas,ipmmu-r8a7743",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe62a0000 0 0x1000>;
@@ -399,6 +401,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -417,6 +422,9 @@
 		icram2:	sram@e6300000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe6300000 0 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe6300000 0x40000>;
 		};
 
 		/* The memory map in the User's Manual maps the cores to
@@ -545,7 +553,9 @@
 			/* doesn't need pinmux */
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a7743";
+			compatible = "renesas,iic-r8a7743",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
 			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;
@@ -574,7 +584,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7743",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -586,11 +596,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
@@ -600,8 +610,8 @@
 			compatible = "renesas,r8a7743-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a0000 0 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 330>;
 			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
@@ -614,8 +624,8 @@
 			compatible = "renesas,r8a7743-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b0000 0 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 331>;
 			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
@@ -628,22 +638,22 @@
 			compatible = "renesas,dmac-r8a7743",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -661,22 +671,22 @@
 			compatible = "renesas,dmac-r8a7743",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -696,6 +706,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -1179,7 +1190,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -1366,20 +1377,20 @@
 			compatible = "renesas,dmac-r8a7743",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1397,20 +1408,20 @@
 			compatible = "renesas,dmac-r8a7743",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec720000 0 0x10000>;
-			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1461,10 +1472,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x800 0 0 0 0>;
@@ -1496,10 +1507,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x10800 0 0 0 0>;
@@ -1514,7 +1525,7 @@
 			};
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7743",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1529,7 +1540,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee140000 {
+		sdhi1: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7743",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1544,7 +1555,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7743",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1611,13 +1622,13 @@
 			#size-cells = <2>;
 			bus-range = <0x00 0xff>;
 			device_type = "pci";
-			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000
-				  0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000
-				  0x02000000 0 0x30000000 0 0x30000000 0 0x08000000
-				  0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000>,
+				 <0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000>,
+				 <0x02000000 0 0x30000000 0 0x30000000 0 0x08000000>,
+				 <0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
 			/* Map all possible DDR as inbound ranges */
-			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000
-				      0x43000000 2 0x00000000 2 0x00000000 1 0x00000000>;
+			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000>,
+				     <0x43000000 2 0x00000000 2 0x00000000 1 0x00000000>;
 			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
@@ -1663,9 +1674,10 @@
 			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7744-iwg20d-q7-dbcm-ca.dts b/arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dts
index 3e58c2e92e03..3e58c2e92e03 100644
--- a/arch/arm/boot/dts/r8a7744-iwg20d-q7-dbcm-ca.dts
+++ b/arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dts
diff --git a/arch/arm/boot/dts/r8a7744-iwg20d-q7.dts b/arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dts
index 1fdac528f274..1fdac528f274 100644
--- a/arch/arm/boot/dts/r8a7744-iwg20d-q7.dts
+++ b/arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dts
diff --git a/arch/arm/boot/dts/r8a7744-iwg20m.dtsi b/arch/arm/boot/dts/renesas/r8a7744-iwg20m.dtsi
index 82ee3c1140ef..82ee3c1140ef 100644
--- a/arch/arm/boot/dts/r8a7744-iwg20m.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7744-iwg20m.dtsi
diff --git a/arch/arm/boot/dts/r8a7744.dtsi b/arch/arm/boot/dts/renesas/r8a7744.dtsi
index fa74a262107b..aa13841f9781 100644
--- a/arch/arm/boot/dts/r8a7744.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7744.dtsi
@@ -49,7 +49,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -59,6 +58,7 @@
 			clocks = <&cpg CPG_CORE R8A7744_CLK_Z>;
 			clock-latency = <300000>; /* 300 us */
 			power-domains = <&sysc R8A7744_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 
 			/* kHz - uV - OPPs unknown yet */
@@ -78,6 +78,7 @@
 			clocks = <&cpg CPG_CORE R8A7744_CLK_Z>;
 			clock-latency = <300000>; /* 300 us */
 			power-domains = <&sysc R8A7744_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 
 			/* kHz - uV - OPPs unknown yet */
@@ -139,6 +140,7 @@
 			compatible = "renesas,r8a7744-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7744_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -265,7 +267,7 @@
 			resets = <&cpg 904>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7744";
 			reg = <0 0xe6060000 0 0x250>;
 		};
@@ -293,7 +295,7 @@
 		apmu@e6152000 {
 			compatible = "renesas,r8a7744-apmu", "renesas,apmu";
 			reg = <0 0xe6152000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -338,7 +340,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7744",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -348,7 +350,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7744",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -357,7 +359,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7744",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -367,7 +369,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7744",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -376,7 +378,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7744",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -386,7 +388,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_gp: mmu@e62a0000 {
+		ipmmu_gp: iommu@e62a0000 {
 			compatible = "renesas,ipmmu-r8a7744",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe62a0000 0 0x1000>;
@@ -399,6 +401,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -417,6 +422,9 @@
 		icram2:	sram@e6300000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe6300000 0 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe6300000 0x40000>;
 		};
 
 		/* The memory map in the User's Manual maps the cores to
@@ -545,7 +553,9 @@
 			/* doesn't need pinmux */
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,iic-r8a7744";
+			compatible = "renesas,iic-r8a7744",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
 			reg = <0 0xe60b0000 0 0x425>;
 			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 926>;
@@ -574,7 +584,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7744",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -586,11 +596,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
@@ -600,8 +610,8 @@
 			compatible = "renesas,r8a7744-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a0000 0 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 330>;
 			power-domains = <&sysc R8A7744_PD_ALWAYS_ON>;
@@ -614,8 +624,8 @@
 			compatible = "renesas,r8a7744-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b0000 0 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 331>;
 			power-domains = <&sysc R8A7744_PD_ALWAYS_ON>;
@@ -628,22 +638,22 @@
 			compatible = "renesas,dmac-r8a7744",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -661,22 +671,22 @@
 			compatible = "renesas,dmac-r8a7744",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -696,6 +706,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7744_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -1179,7 +1190,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -1366,20 +1377,20 @@
 			compatible = "renesas,dmac-r8a7744",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1397,20 +1408,20 @@
 			compatible = "renesas,dmac-r8a7744",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec720000 0 0x10000>;
-			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1461,10 +1472,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x800 0 0 0 0>;
@@ -1496,10 +1507,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x10800 0 0 0 0>;
@@ -1514,7 +1525,7 @@
 			};
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7744",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1529,7 +1540,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee140000 {
+		sdhi1: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7744",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1544,7 +1555,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7744",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1597,13 +1608,13 @@
 			#size-cells = <2>;
 			bus-range = <0x00 0xff>;
 			device_type = "pci";
-			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000
-				  0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000
-				  0x02000000 0 0x30000000 0 0x30000000 0 0x08000000
-				  0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000>,
+				 <0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000>,
+				 <0x02000000 0 0x30000000 0 0x30000000 0 0x08000000>,
+				 <0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
 			/* Map all possible DDR as inbound ranges */
-			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000
-				      0x43000000 2 0x00000000 2 0x00000000 1 0x00000000>;
+			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000>,
+				     <0x43000000 2 0x00000000 2 0x00000000 1 0x00000000>;
 			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
@@ -1649,9 +1660,10 @@
 			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm-dbhd-ca.dts b/arch/arm/boot/dts/renesas/r8a7745-iwg22d-sodimm-dbhd-ca.dts
index 2aeebfc9e4f1..a0b574398055 100644
--- a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm-dbhd-ca.dts
+++ b/arch/arm/boot/dts/renesas/r8a7745-iwg22d-sodimm-dbhd-ca.dts
@@ -34,6 +34,15 @@
 			};
 		};
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &du {
@@ -81,11 +90,15 @@
 		clock-names = "cec";
 		pd-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
 
+		avdd-supply = <&reg_1p8v>;
+		dvdd-supply = <&reg_1p8v>;
+		pvdd-supply = <&reg_1p8v>;
+		dvdd-3v-supply = <&reg_3p3v>;
+		bgvdd-supply = <&reg_1p8v>;
+
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
@@ -108,6 +121,12 @@
 	};
 };
 
+&lcd_panel {
+	status = "disabled";
+
+	/delete-node/ port;
+};
+
 &pfc {
 	can1_pins: can1 {
 		groups = "can1_data_b";
diff --git a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts b/arch/arm/boot/dts/renesas/r8a7745-iwg22d-sodimm.dts
index ce6603b0994b..24411044ef6c 100644
--- a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts
+++ b/arch/arm/boot/dts/renesas/r8a7745-iwg22d-sodimm.dts
@@ -30,6 +30,7 @@
 
 /dts-v1/;
 #include "r8a7745-iwg22m.dtsi"
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "iWave Systems RainboW-G22D-SODIMM board based on RZ/G1E";
@@ -52,21 +53,34 @@
 		clock-frequency = <26000000>;
 	};
 
-	rsnd_sgtl5000: sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&sndcodec>;
-		simple-audio-card,frame-master = <&sndcodec>;
+	backlight_lcd: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&tpu 3 5000000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+	};
 
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
+	lcd_panel: lcd {
+		compatible = "edt,etm043080dh6gp";
+		power-supply = <&vccq_panel>;
+		backlight = <&backlight_lcd>;
 
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&sgtl5000>;
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&du_out_rgb0>;
+			};
 		};
 	};
 
+	vccq_panel: regulator-vccq-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "Panel VccQ";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
+
 	vccq_sdhi0: regulator-vccq-sdhi0 {
 		compatible = "regulator-gpio";
 
@@ -76,8 +90,22 @@
 
 		gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	rsnd_sgtl5000: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&sndcodec>;
+		simple-audio-card,frame-master = <&sndcodec>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+		};
 	};
 };
 
@@ -95,6 +123,8 @@
 	 * On some older versions of the platform (before R4.0) the phy address
 	 * may be 1 or 3. The address is fixed to 3 for R4.0 onwards.
 	 */
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		micrel,led-mode = <1>;
 	};
@@ -107,6 +137,21 @@
 	status = "okay";
 };
 
+&du {
+	pinctrl-0 = <&du0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&lcd_in>;
+			};
+		};
+	};
+};
+
 &hscif1 {
 	pinctrl-0 = <&hscif1_pins>;
 	pinctrl-names = "default";
@@ -136,6 +181,39 @@
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};
+
+	port-expander@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+		/* 3.25 MHz ADC clock speed */
+		st,adc-freq = <1>;
+		/* ADC conversion time: 80 clocks */
+		st,sample-time = <4>;
+		/* 12-bit ADC */
+		st,mod-12b = <1>;
+		/* internal ADC reference */
+		st,ref-sel = <0>;
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			/* 8 sample average control */
+			st,ave-ctrl = <3>;
+			/* 7 length fractional part in z */
+			st,fraction-z = <7>;
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			/* 1 ms panel driver settling time */
+			st,settling = <3>;
+			/* 5 ms touch detect interrupt delay */
+			st,touch-det-delay = <5>;
+		};
+	};
 };
 
 &pci1 {
@@ -150,11 +228,21 @@
 		function = "avb";
 	};
 
+	backlight_pins: backlight {
+		groups = "tpu_to3_c";
+		function = "tpu";
+	};
+
 	can0_pins: can0 {
 		groups = "can0_data";
 		function = "can0";
 	};
 
+	du0_pins: du0 {
+		groups = "du0_rgb666", "du0_sync", "du0_disp", "du0_clk0_out";
+		function = "du0";
+	};
+
 	hscif1_pins: hscif1 {
 		groups = "hscif1_data", "hscif1_ctrl";
 		function = "hscif1";
@@ -203,8 +291,8 @@
 
 	rcar_sound,dai {
 		dai0 {
-			playback = <&ssi3 &src3 &dvc0>;
-			capture = <&ssi4 &src4 &dvc1>;
+			playback = <&ssi3>, <&src3>, <&dvc0>;
+			capture = <&ssi4>, <&src4>, <&dvc1>;
 		};
 	};
 };
@@ -230,6 +318,12 @@
 	shared-pin;
 };
 
+&tpu {
+	pinctrl-0 = <&backlight_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
 &usbphy {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/r8a7745-iwg22m.dtsi b/arch/arm/boot/dts/renesas/r8a7745-iwg22m.dtsi
index 41f111b99a75..41f111b99a75 100644
--- a/arch/arm/boot/dts/r8a7745-iwg22m.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7745-iwg22m.dtsi
diff --git a/arch/arm/boot/dts/r8a7745-sk-rzg1e.dts b/arch/arm/boot/dts/renesas/r8a7745-sk-rzg1e.dts
index db72a801abe5..0a75e8c79acc 100644
--- a/arch/arm/boot/dts/r8a7745-sk-rzg1e.dts
+++ b/arch/arm/boot/dts/renesas/r8a7745-sk-rzg1e.dts
@@ -7,6 +7,7 @@
 
 /dts-v1/;
 #include "r8a7745.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "SK-RZG1E";
@@ -56,7 +57,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -64,9 +65,12 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	};
 };
diff --git a/arch/arm/boot/dts/r8a7745.dtsi b/arch/arm/boot/dts/renesas/r8a7745.dtsi
index c53f7ff20695..44688b8431c3 100644
--- a/arch/arm/boot/dts/r8a7745.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7745.dtsi
@@ -64,7 +64,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -73,6 +72,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A7745_CLK_Z2>;
 			power-domains = <&sysc R8A7745_PD_CA7_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 		};
 
@@ -83,6 +83,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A7745_CLK_Z2>;
 			power-domains = <&sysc R8A7745_PD_CA7_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 		};
 
@@ -230,7 +231,7 @@
 			resets = <&cpg 905>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7745";
 			reg = <0 0xe6060000 0 0x11c>;
 		};
@@ -258,7 +259,7 @@
 		apmu@e6151000 {
 			compatible = "renesas,r8a7745-apmu", "renesas,apmu";
 			reg = <0 0xe6151000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -269,6 +270,7 @@
 		rwdt: watchdog@e6020000 {
 			compatible = "renesas,r8a7745-wdt",
 				     "renesas,rcar-gen2-wdt";
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			reg = <0 0xe6020000 0 0x0c>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
@@ -302,7 +304,7 @@
 			resets = <&cpg 407>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7745",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -312,7 +314,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7745",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -321,7 +323,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7745",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -331,7 +333,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7745",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -340,7 +342,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7745",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -350,7 +352,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_gp: mmu@e62a0000 {
+		ipmmu_gp: iommu@e62a0000 {
 			compatible = "renesas,ipmmu-r8a7745",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe62a0000 0 0x1000>;
@@ -363,6 +365,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -381,6 +386,9 @@
 		icram2:	sram@e6300000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe6300000 0 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe6300000 0x40000>;
 		};
 		i2c0: i2c@e6508000 {
 			#address-cells = <1>;
@@ -517,7 +525,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7745",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -529,11 +537,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
@@ -543,8 +551,8 @@
 			compatible = "renesas,r8a7745-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a0000 0 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 330>;
 			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
@@ -557,8 +565,8 @@
 			compatible = "renesas,r8a7745-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b0000 0 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 331>;
 			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
@@ -571,22 +579,22 @@
 			compatible = "renesas,dmac-r8a7745",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -604,22 +612,22 @@
 			compatible = "renesas,dmac-r8a7745",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -639,6 +647,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -1111,7 +1120,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>; <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>; <&rcar_sound N>;
@@ -1293,20 +1302,20 @@
 			compatible = "renesas,dmac-r8a7745",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1337,10 +1346,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x800 0 0 0 0>;
@@ -1372,10 +1381,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x10800 0 0 0 0>;
@@ -1390,7 +1399,7 @@
 			};
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7745",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1405,7 +1414,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee140000 {
+		sdhi1: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7745",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1420,7 +1429,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7745",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1500,11 +1509,12 @@
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7745";
 			reg = <0 0xfeb00000 0 0x40000>;
-			reg-names = "du";
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts b/arch/arm/boot/dts/renesas/r8a77470-iwg23s-sbc.dts
index 450efe923008..644802285249 100644
--- a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
+++ b/arch/arm/boot/dts/renesas/r8a77470-iwg23s-sbc.dts
@@ -65,8 +65,7 @@
 
 		gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 };
 
@@ -80,6 +79,8 @@
 	status = "okay";
 
 	phy3: ethernet-phy@3 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <3>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
@@ -115,7 +116,7 @@
 };
 
 &gpio2 {
-	interrupt-fixup {
+	interrupt-fixup-hog {
 		gpio-hog;
 		gpios = <29 GPIO_ACTIVE_HIGH>;
 		line-name = "hdmi-hpd-int";
diff --git a/arch/arm/boot/dts/r8a77470.dtsi b/arch/arm/boot/dts/renesas/r8a77470.dtsi
index 51806c7f486a..a5cf663a0118 100644
--- a/arch/arm/boot/dts/r8a77470.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a77470.dtsi
@@ -25,7 +25,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -34,6 +33,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A77470_CLK_Z2>;
 			power-domains = <&sysc R8A77470_PD_CA7_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 		};
 
@@ -44,6 +44,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A77470_CLK_Z2>;
 			power-domains = <&sysc R8A77470_PD_CA7_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 		};
 
@@ -90,6 +91,7 @@
 			compatible = "renesas,r8a77470-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -187,7 +189,7 @@
 			resets = <&cpg 907>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a77470";
 			reg = <0 0xe6060000 0 0x118>;
 		};
@@ -205,7 +207,7 @@
 		apmu@e6151000 {
 			compatible = "renesas,r8a77470-apmu", "renesas,apmu";
 			reg = <0 0xe6151000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -242,6 +244,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -260,6 +265,9 @@
 		icram2:	sram@e6300000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe6300000 0 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe6300000 0x20000>;
 		};
 
 		i2c0: i2c@e6508000 {
@@ -349,7 +357,7 @@
 			status = "disabled";
 		};
 
-		usbphy0: usb-phy@e6590100 {
+		usbphy0: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a77470",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -361,7 +369,7 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
@@ -385,7 +393,7 @@
 			status = "disabled";
 		};
 
-		usbphy1: usb-phy@e6598100 {
+		usbphy1: usb-phy-controller@e6598100 {
 			compatible = "renesas,usb-phy-r8a77470",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6598100 0 0x100>;
@@ -397,7 +405,7 @@
 			resets = <&cpg 706>;
 			status = "disabled";
 
-			usb1: usb-channel@0 {
+			usb1: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
@@ -407,8 +415,8 @@
 			compatible = "renesas,r8a77470-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a0000 0 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 330>;
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
@@ -421,8 +429,8 @@
 			compatible = "renesas,r8a77470-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b0000 0 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 331>;
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
@@ -435,8 +443,8 @@
 			compatible = "renesas,r8a77470-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a8000 0 0x100>;
-			interrupts = <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 326>;
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
@@ -449,8 +457,8 @@
 			compatible = "renesas,r8a77470-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b8000 0 0x100>;
-			interrupts = <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 327>;
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
@@ -463,22 +471,22 @@
 			compatible = "renesas,dmac-r8a77470",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -496,22 +504,22 @@
 			compatible = "renesas,dmac-r8a77470",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -531,6 +539,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -876,7 +885,7 @@
 			status = "disabled";
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a77470",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -891,7 +900,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee300000 {
+		sdhi1: mmc@ee300000 {
 			compatible = "renesas,sdhi-mmc-r8a77470";
 			reg = <0 0xee300000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
@@ -902,7 +911,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a77470",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x328>;
@@ -936,9 +945,10 @@
 			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/renesas/r8a7778-bockw.dts
index 6c7b07c4b9d3..a3f9d74e8877 100644
--- a/arch/arm/boot/dts/r8a7778-bockw.dts
+++ b/arch/arm/boot/dts/renesas/r8a7778-bockw.dts
@@ -62,8 +62,37 @@
 };
 
 &bsc {
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0x0 0x04000000>;
+		pinctrl-0 = <&flash_pins>;
+		pinctrl-names = "default";
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition@40000 {
+				label = "uboot-env";
+				reg = <0x00040000 0x00040000>;
+				read-only;
+			};
+			partition@80000 {
+				label = "flash";
+				reg = <0x00080000 0x03f80000>;
+			};
+		};
+	};
+
 	ethernet@18300000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan89218", "smsc,lan9115";
 		reg = <0x18300000 0x1000>;
 
 		phy-mode = "mii";
@@ -126,6 +155,11 @@
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
+	flash_pins: flash {
+		groups = "lbsc_cs0";
+		function = "lbsc";
+	};
+
 	scif0_pins: scif0 {
 		groups = "scif0_data_a", "scif0_ctrl";
 		function = "scif0";
diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/renesas/r8a7778.dtsi
index 10d996d2941f..8d4530ed2fc6 100644
--- a/arch/arm/boot/dts/r8a7778.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7778.dtsi
@@ -78,11 +78,12 @@
 			<0xfe780010 4>,
 			<0xfe780024 4>,
 			<0xfe780044 4>,
-			<0xfe780064 4>;
-		interrupts =   <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			<0xfe780064 4>,
+			<0xfe780000 4>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		sense-bitfield-width = <2>;
 	};
 
@@ -141,7 +142,7 @@
 		interrupt-controller;
 	};
 
-	pfc: pin-controller@fffc0000 {
+	pfc: pinctrl@fffc0000 {
 		compatible = "renesas,pfc-r8a7778";
 		reg = <0xfffc0000 0x118>;
 	};
@@ -165,6 +166,7 @@
 		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C1>;
 		power-domains = <&cpg_clocks>;
+		i2c-scl-internal-delay-ns = <5>;
 		status = "disabled";
 	};
 
@@ -176,6 +178,7 @@
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C2>;
 		power-domains = <&cpg_clocks>;
+		i2c-scl-internal-delay-ns = <5>;
 		status = "disabled";
 	};
 
@@ -187,6 +190,7 @@
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C3>;
 		power-domains = <&cpg_clocks>;
+		i2c-scl-internal-delay-ns = <5>;
 		status = "disabled";
 	};
 
@@ -237,7 +241,7 @@
 
 	rcar_sound: sound@ffd90000 {
 		/*
-		 * #sound-dai-cells is required
+		 * #sound-dai-cells is required if simple-card
 		 *
 		 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 		 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -400,7 +404,7 @@
 		status = "disabled";
 	};
 
-	sdhi0: sd@ffe4c000 {
+	sdhi0: mmc@ffe4c000 {
 		compatible = "renesas,sdhi-r8a7778",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4c000 0x100>;
@@ -410,7 +414,7 @@
 		status = "disabled";
 	};
 
-	sdhi1: sd@ffe4d000 {
+	sdhi1: mmc@ffe4d000 {
 		compatible = "renesas,sdhi-r8a7778",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4d000 0x100>;
@@ -420,7 +424,7 @@
 		status = "disabled";
 	};
 
-	sdhi2: sd@ffe4f000 {
+	sdhi2: mmc@ffe4f000 {
 		compatible = "renesas,sdhi-r8a7778",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4f000 0x100>;
@@ -498,14 +502,17 @@
 		audio_clk_a: audio_clk_a {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			clock-frequency = <0>;
 		};
 		audio_clk_b: audio_clk_b {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			clock-frequency = <0>;
 		};
 		audio_clk_c: audio_clk_c {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			clock-frequency = <0>;
 		};
 
 		/* Fixed ratio clocks */
diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/renesas/r8a7779-marzen.dts
index c755f0b8fd0d..9b13e8d1538b 100644
--- a/arch/arm/boot/dts/r8a7779-marzen.dts
+++ b/arch/arm/boot/dts/renesas/r8a7779-marzen.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 #include "r8a7779.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
@@ -48,23 +49,52 @@
 
 		gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
-	ethernet@18000000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
-		reg = <0x18000000 0x100>;
-		pinctrl-0 = <&ethernet_pins>;
+	keypad-0 {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keypad0_pins>;
 		pinctrl-names = "default";
 
-		phy-mode = "mii";
-		interrupt-parent = <&irqpin0>;
-		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-		smsc,irq-push-pull;
-		reg-io-width = <4>;
-		vddvario-supply = <&fixedregulator3v3>;
-		vdd33a-supply = <&fixedregulator3v3>;
+		interrupt-parent = <&gpio0>;
+
+		key-1 {
+			interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
+			linux,code = <KEY_1>;
+			label = "SW1-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+			linux,code = <KEY_2>;
+			label = "SW1-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
+	keypad-1 {
+		compatible = "gpio-keys-polled";
+		poll-interval = <50>;
+
+		pinctrl-0 = <&keypad1_pins>;
+		pinctrl-names = "default";
+
+		key-3 {
+			gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW1-3";
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW1-4";
+			debounce-interval = <20>;
+		};
 	};
 
 	leds {
@@ -146,7 +176,7 @@
 	status = "okay";
 
 	clocks = <&mstp1_clks R8A7779_CLK_DU>, <&x3_clk>;
-	clock-names = "du", "dclkin.0";
+	clock-names = "du.0", "dclkin.0";
 
 	ports {
 		port@0 {
@@ -162,6 +192,20 @@
 	};
 };
 
+&gpio0 {
+	keypad0-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_LOW>, <18 GPIO_ACTIVE_LOW>;
+		input;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <100000>;
+};
+
 &irqpin0 {
 	status = "okay";
 };
@@ -170,6 +214,52 @@
 	clock-frequency = <31250000>;
 };
 
+&lbsc {
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0x0 0x04000000>;
+		pinctrl-0 = <&flash_pins>;
+		pinctrl-names = "default";
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition@40000 {
+				label = "uboot-env";
+				reg = <0x00040000 0x00040000>;
+				read-only;
+			};
+			partition@80000 {
+				label = "flash";
+				reg = <0x00080000 0x03f80000>;
+			};
+		};
+	};
+
+	ethernet@18000000 {
+		compatible = "smsc,lan89218", "smsc,lan9115";
+		reg = <0x18000000 0x100>;
+		pinctrl-0 = <&ethernet_pins>;
+		pinctrl-names = "default";
+
+		phy-mode = "mii";
+		interrupt-parent = <&irqpin0>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		smsc,irq-push-pull;
+		reg-io-width = <4>;
+		vddvario-supply = <&fixedregulator3v3>;
+		vdd33a-supply = <&fixedregulator3v3>;
+	};
+};
+
 &tmu0 {
 	status = "okay";
 };
@@ -205,6 +295,11 @@
 		};
 	};
 
+	flash_pins: flash {
+		groups = "lbsc_cs0";
+		function = "lbsc";
+	};
+
 	scif2_pins: scif2 {
 		groups = "scif2_data_c";
 		function = "scif2";
@@ -224,6 +319,15 @@
 		groups = "hspi0";
 		function = "hspi0";
 	};
+
+	keypad0_pins: keypad-0 {
+		pins = "GP_0_17", "GP_0_18";
+		bias-pull-up;
+	};
+	keypad1_pins: keypad-1 {
+		pins = "GP_0_19", "GP_0_20";
+		bias-pull-up;
+	};
 };
 
 &sata {
diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/renesas/r8a7779.dtsi
index ebf5b7cfe215..7743af5e2a6f 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7779.dtsi
@@ -68,6 +68,14 @@
 		      <0xf0000100 0x100>;
 	};
 
+	timer@f0000200 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0xf0000200 0x100>;
+		interrupts = <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+		clocks = <&cpg_clocks R8A7779_CLK_ZS>;
+	};
+
 	timer@f0000600 {
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0xf0000600 0x20>;
@@ -164,10 +172,10 @@
 			<0xfe780044 4>,
 			<0xfe780064 4>,
 			<0xfe780000 4>;
-		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		sense-bitfield-width = <2>;
 	};
 
@@ -190,6 +198,7 @@
 		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C1>;
 		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		i2c-scl-internal-delay-ns = <5>;
 		status = "disabled";
 	};
 
@@ -201,6 +210,7 @@
 		interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C2>;
 		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		i2c-scl-internal-delay-ns = <5>;
 		status = "disabled";
 	};
 
@@ -212,6 +222,7 @@
 		interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C3>;
 		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		i2c-scl-internal-delay-ns = <5>;
 		status = "disabled";
 	};
 
@@ -313,7 +324,70 @@
 		status = "disabled";
 	};
 
-	pfc: pin-controller@fffc0000 {
+	pwm0: pwm@ffe50000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe50000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pwm1: pwm@ffe51000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe51000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pwm2: pwm@ffe52000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe52000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pwm3: pwm@ffe53000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe53000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pwm4: pwm@ffe54000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe54000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pwm5: pwm@ffe55000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe55000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pwm6: pwm@ffe56000 {
+		compatible = "renesas,pwm-r8a7779", "renesas,pwm-rcar";
+		reg = <0xffe56000 0x8>;
+		clocks = <&mstp0_clks R8A7779_CLK_PWM>;
+		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	pfc: pinctrl@fffc0000 {
 		compatible = "renesas,pfc-r8a7779";
 		reg = <0xfffc0000 0x23c>;
 	};
@@ -369,7 +443,7 @@
 	};
 
 	sata: sata@fc600000 {
-		compatible = "renesas,sata-r8a7779", "renesas,rcar-sata";
+		compatible = "renesas,sata-r8a7779";
 		reg = <0xfc600000 0x200000>;
 		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp1_clks R8A7779_CLK_SATA>;
@@ -377,7 +451,7 @@
 		status = "disabled";
 	};
 
-	sdhi0: sd@ffe4c000 {
+	sdhi0: mmc@ffe4c000 {
 		compatible = "renesas,sdhi-r8a7779",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4c000 0x100>;
@@ -387,7 +461,7 @@
 		status = "disabled";
 	};
 
-	sdhi1: sd@ffe4d000 {
+	sdhi1: mmc@ffe4d000 {
 		compatible = "renesas,sdhi-r8a7779",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4d000 0x100>;
@@ -397,7 +471,7 @@
 		status = "disabled";
 	};
 
-	sdhi2: sd@ffe4e000 {
+	sdhi2: mmc@ffe4e000 {
 		compatible = "renesas,sdhi-r8a7779",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4e000 0x100>;
@@ -407,7 +481,7 @@
 		status = "disabled";
 	};
 
-	sdhi3: sd@ffe4f000 {
+	sdhi3: mmc@ffe4f000 {
 		compatible = "renesas,sdhi-r8a7779",
 			     "renesas,rcar-gen1-sdhi";
 		reg = <0xffe4f000 0x100>;
@@ -455,6 +529,7 @@
 		reg = <0xfff80000 0x40000>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp1_clks R8A7779_CLK_DU>;
+		clock-names = "du.0";
 		power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
 		status = "disabled";
 
@@ -542,7 +617,8 @@
 			compatible = "renesas,r8a7779-mstp-clocks",
 				     "renesas,cpg-mstp-clocks";
 			reg = <0xffc80030 4>;
-			clocks = <&cpg_clocks R8A7779_CLK_S>,
+			clocks = <&cpg_clocks R8A7779_CLK_P>,
+				 <&cpg_clocks R8A7779_CLK_S>,
 				 <&cpg_clocks R8A7779_CLK_P>,
 				 <&cpg_clocks R8A7779_CLK_P>,
 				 <&cpg_clocks R8A7779_CLK_P>,
@@ -560,20 +636,21 @@
 				 <&cpg_clocks R8A7779_CLK_P>;
 			#clock-cells = <1>;
 			clock-indices = <
-				R8A7779_CLK_HSPI R8A7779_CLK_TMU2
-				R8A7779_CLK_TMU1 R8A7779_CLK_TMU0
-				R8A7779_CLK_HSCIF1 R8A7779_CLK_HSCIF0
-				R8A7779_CLK_SCIF5 R8A7779_CLK_SCIF4
-				R8A7779_CLK_SCIF3 R8A7779_CLK_SCIF2
-				R8A7779_CLK_SCIF1 R8A7779_CLK_SCIF0
-				R8A7779_CLK_I2C3 R8A7779_CLK_I2C2
-				R8A7779_CLK_I2C1 R8A7779_CLK_I2C0
+				R8A7779_CLK_PWM R8A7779_CLK_HSPI
+				R8A7779_CLK_TMU2 R8A7779_CLK_TMU1
+				R8A7779_CLK_TMU0 R8A7779_CLK_HSCIF1
+				R8A7779_CLK_HSCIF0 R8A7779_CLK_SCIF5
+				R8A7779_CLK_SCIF4 R8A7779_CLK_SCIF3
+				R8A7779_CLK_SCIF2 R8A7779_CLK_SCIF1
+				R8A7779_CLK_SCIF0 R8A7779_CLK_I2C3
+				R8A7779_CLK_I2C2 R8A7779_CLK_I2C1
+				R8A7779_CLK_I2C0
 			>;
 			clock-output-names =
-				"hspi", "tmu2", "tmu1", "tmu0", "hscif1",
-				"hscif0", "scif5", "scif4", "scif3", "scif2",
-				"scif1", "scif0", "i2c3", "i2c2", "i2c1",
-				"i2c0";
+				"pwm", "hspi", "tmu2", "tmu1", "tmu0",
+				"hscif1", "hscif0", "scif5", "scif4", "scif3",
+				"scif2", "scif1", "scif0", "i2c3", "i2c2",
+				"i2c1", "i2c0";
 		};
 		mstp1_clks: clocks@ffc80034 {
 			compatible = "renesas,r8a7779-mstp-clocks",
@@ -622,6 +699,13 @@
 		};
 	};
 
+	lbsc: lbsc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0x1c000000>;
+	};
+
 	prr: chipid@ff000044 {
 		compatible = "renesas,prr";
 		reg = <0xff000044 4>;
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/renesas/r8a7790-lager.dts
index 6ec2cf7eb354..2fba4d084001 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/renesas/r8a7790-lager.dts
@@ -53,6 +53,9 @@
 		i2c11 = &i2cexio1;
 		i2c12 = &i2chdmi;
 		i2c13 = &i2cpwr;
+		mmc0 = &mmcif1;
+		mmc1 = &sdhi0;
+		mmc2 = &sdhi2;
 	};
 
 	chosen {
@@ -70,14 +73,12 @@
 		reg = <1 0x40000000 0 0xc0000000>;
 	};
 
-	lbsc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-
 	keyboard {
 		compatible = "gpio-keys";
 
+		pinctrl-0 = <&keyboard_pins>;
+		pinctrl-names = "default";
+
 		one {
 			linux,code = <KEY_1>;
 			label = "SW2-1";
@@ -121,6 +122,15 @@
 		};
 	};
 
+	fixedregulator1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	fixedregulator3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
@@ -150,8 +160,7 @@
 
 		gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi2: regulator-vcc-sdhi2 {
@@ -174,8 +183,7 @@
 
 		gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	audio_clock: audio_clock {
@@ -304,7 +312,7 @@
 	 *
 	 * IIC0/I2C0 does not appear to support fallback to GPIO.
 	 */
-	i2cexio0: i2c-10 {
+	i2cexio0: i2c-mux1 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&iic0>, <&i2c0>;
 		i2c-bus-name = "i2c-exio0";
@@ -317,7 +325,7 @@
 	 * This is similar to the arangement described for i2cexio0 (above)
 	 * with a fallback to GPIO also provided.
 	 */
-	i2cexio1: i2c-11 {
+	i2cexio1: i2c-mux2 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
 		i2c-bus-name = "i2c-exio1";
@@ -329,7 +337,7 @@
 	 * IIC2 and I2C2 may be switched using pinmux.
 	 * A fallback to GPIO is also provided.
 	 */
-	i2chdmi: i2c-12 {
+	i2chdmi: i2c-mux3 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
 		i2c-bus-name = "i2c-hdmi";
@@ -345,7 +353,6 @@
 		composite-in@20 {
 			compatible = "adi,adv7180";
 			reg = <0x20>;
-			remote = <&vin1>;
 
 			port {
 				adv7180: endpoint {
@@ -363,11 +370,15 @@
 			clocks = <&cec_clock>;
 			clock-names = "cec";
 
+			avdd-supply = <&fixedregulator1v8>;
+			dvdd-supply = <&fixedregulator1v8>;
+			pvdd-supply = <&fixedregulator1v8>;
+			dvdd-3v-supply = <&fixedregulator3v3>;
+			bgvdd-supply = <&fixedregulator1v8>;
+
 			adi,input-depth = <8>;
 			adi,input-colorspace = "rgb";
 			adi,input-clock = "1x";
-			adi,input-style = <1>;
-			adi,input-justification = "evenly";
 
 			ports {
 				#address-cells = <1>;
@@ -421,7 +432,7 @@
 	 * IIC3 and I2C3 may be switched using pinmux.
 	 * IIC3/I2C3 does not appear to support fallback to GPIO.
 	 */
-	i2cpwr: i2c-13 {
+	i2cpwr: i2c-mux4 {
 		compatible = "i2c-demux-pinctrl";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pmic_irq_pins>;
@@ -441,7 +452,7 @@
 				compatible = "dlg,da9063-rtc";
 			};
 
-			wdt {
+			watchdog {
 				compatible = "dlg,da9063-watchdog";
 			};
 		};
@@ -661,10 +672,15 @@
 		groups = "audio_clk_a";
 		function = "audio_clk";
 	};
+
+	keyboard_pins: keyboard {
+		pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28";
+		bias-pull-up;
+	};
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -672,10 +688,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -912,7 +931,7 @@
 };
 
 &rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
 	pinctrl-names = "default";
 
 	/* Single DAI */
@@ -922,8 +941,8 @@
 
 	rcar_sound,dai {
 		dai0 {
-			playback = <&ssi0 &src2 &dvc0>;
-			capture  = <&ssi1 &src3 &dvc1>;
+			playback = <&ssi0>, <&src2>, <&dvc0>;
+			capture  = <&ssi1>, <&src3>, <&dvc1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/r8a7790-stout.dts b/arch/arm/boot/dts/renesas/r8a7790-stout.dts
index a315ba749aa4..f9bc5b4f019d 100644
--- a/arch/arm/boot/dts/r8a7790-stout.dts
+++ b/arch/arm/boot/dts/renesas/r8a7790-stout.dts
@@ -44,6 +44,15 @@
 		};
 	};
 
+	fixedregulator1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	fixedregulator3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
@@ -191,7 +200,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -199,10 +208,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -293,11 +305,15 @@
 		clocks = <&osc4_clk>;
 		clock-names = "cec";
 
+		avdd-supply = <&fixedregulator1v8>;
+		dvdd-supply = <&fixedregulator1v8>;
+		pvdd-supply = <&fixedregulator1v8>;
+		dvdd-3v-supply = <&fixedregulator3v3>;
+		bgvdd-supply = <&fixedregulator1v8>;
+
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
@@ -322,7 +338,7 @@
 
 &iic3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&iic3_pins &pmic_irq_pins>;
+	pinctrl-0 = <&iic3_pins>, <&pmic_irq_pins>;
 	status = "okay";
 
 	pmic@58 {
@@ -340,7 +356,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/renesas/r8a7790.dtsi
index 5a2747758f67..46fb81f5062f 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7790.dtsi
@@ -69,7 +69,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -78,6 +77,7 @@
 			clock-frequency = <1300000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z>;
 			power-domains = <&sysc R8A7790_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 			capacity-dmips-mhz = <1024>;
 			voltage-tolerance = <1>; /* 1% */
@@ -99,6 +99,7 @@
 			clock-frequency = <1300000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z>;
 			power-domains = <&sysc R8A7790_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 			capacity-dmips-mhz = <1024>;
 			voltage-tolerance = <1>; /* 1% */
@@ -120,6 +121,7 @@
 			clock-frequency = <1300000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z>;
 			power-domains = <&sysc R8A7790_PD_CA15_CPU2>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 			capacity-dmips-mhz = <1024>;
 			voltage-tolerance = <1>; /* 1% */
@@ -141,6 +143,7 @@
 			clock-frequency = <1300000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z>;
 			power-domains = <&sysc R8A7790_PD_CA15_CPU3>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 			capacity-dmips-mhz = <1024>;
 			voltage-tolerance = <1>; /* 1% */
@@ -162,6 +165,7 @@
 			clock-frequency = <780000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z2>;
 			power-domains = <&sysc R8A7790_PD_CA7_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 			capacity-dmips-mhz = <539>;
 		};
@@ -173,6 +177,7 @@
 			clock-frequency = <780000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z2>;
 			power-domains = <&sysc R8A7790_PD_CA7_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 			capacity-dmips-mhz = <539>;
 		};
@@ -184,6 +189,7 @@
 			clock-frequency = <780000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z2>;
 			power-domains = <&sysc R8A7790_PD_CA7_CPU2>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 			capacity-dmips-mhz = <539>;
 		};
@@ -195,6 +201,7 @@
 			clock-frequency = <780000000>;
 			clocks = <&cpg CPG_CORE R8A7790_CLK_Z2>;
 			power-domains = <&sysc R8A7790_PD_CA7_CPU3>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 			capacity-dmips-mhz = <539>;
 		};
@@ -267,6 +274,7 @@
 			compatible = "renesas,r8a7790-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -363,11 +371,22 @@
 			resets = <&cpg 907>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7790";
 			reg = <0 0xe6060000 0 0x250>;
 		};
 
+		tpu: pwm@e60f0000 {
+			compatible = "renesas,tpu-r8a7790", "renesas,tpu";
+			reg = <0 0xe60f0000 0 0x148>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 304>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 304>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		cpg: clock-controller@e6150000 {
 			compatible = "renesas,r8a7790-cpg-mssr";
 			reg = <0 0xe6150000 0 0x1000>;
@@ -381,13 +400,13 @@
 		apmu@e6151000 {
 			compatible = "renesas,r8a7790-apmu", "renesas,apmu";
 			reg = <0 0xe6151000 0 0x188>;
-			cpus = <&cpu4 &cpu5 &cpu6 &cpu7>;
+			cpus = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
 		};
 
 		apmu@e6152000 {
 			compatible = "renesas,r8a7790-apmu", "renesas,apmu";
 			reg = <0 0xe6152000 0 0x188>;
-			cpus = <&cpu0 &cpu1 &cpu2 &cpu3>;
+			cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -427,7 +446,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7790",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -437,7 +456,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7790",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -446,7 +465,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7790",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -456,7 +475,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7790",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -465,7 +484,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7790",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -475,7 +494,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_rt: mmu@ffc80000 {
+		ipmmu_rt: iommu@ffc80000 {
 			compatible = "renesas,ipmmu-r8a7790",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xffc80000 0 0x1000>;
@@ -487,6 +506,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -643,7 +665,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7790",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -655,11 +677,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
@@ -669,8 +691,8 @@
 			compatible = "renesas,r8a7790-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a0000 0 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 330>;
 			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
@@ -683,8 +705,8 @@
 			compatible = "renesas,r8a7790-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b0000 0 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 331>;
 			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
@@ -697,22 +719,22 @@
 			compatible = "renesas,dmac-r8a7790",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -730,22 +752,22 @@
 			compatible = "renesas,dmac-r8a7790",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -765,6 +787,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -1025,6 +1048,76 @@
 			status = "disabled";
 		};
 
+		pwm0: pwm@e6e30000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e30000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@e6e31000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e31000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm2: pwm@e6e32000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e32000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm3: pwm@e6e33000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e33000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm4: pwm@e6e34000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e34000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm5: pwm@e6e35000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e35000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm6: pwm@e6e36000 {
+			compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+			reg = <0 0xe6e36000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
 		can0: can@e6e80000 {
 			compatible = "renesas,can-r8a7790",
 				     "renesas,rcar-gen2-can";
@@ -1097,7 +1190,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -1240,7 +1333,7 @@
 					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi1: ssi-1 {
-					 interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
 					dmas = <&audma0 0x03>, <&audma1 0x04>,
 					       <&audma0 0x49>, <&audma1 0x4a>;
 					dma-names = "rx", "tx", "rxu", "txu";
@@ -1300,20 +1393,20 @@
 			compatible = "renesas,dmac-r8a7790",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1331,20 +1424,20 @@
 			compatible = "renesas,dmac-r8a7790",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec720000 0 0x10000>;
-			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1388,10 +1481,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x800 0 0 0 0>;
@@ -1423,10 +1516,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0a0000 0 0xee0a0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		pci2: pci@ee0d0000 {
@@ -1446,10 +1539,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x20800 0 0 0 0>;
@@ -1464,7 +1557,7 @@
 			};
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7790",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1479,7 +1572,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee120000 {
+		sdhi1: mmc@ee120000 {
 			compatible = "renesas,sdhi-r8a7790",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee120000 0 0x328>;
@@ -1494,7 +1587,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee140000 {
+		sdhi2: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7790",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1509,7 +1602,7 @@
 			status = "disabled";
 		};
 
-		sdhi3: sd@ee160000 {
+		sdhi3: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7790",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1614,13 +1707,13 @@
 			#size-cells = <2>;
 			bus-range = <0x00 0xff>;
 			device_type = "pci";
-			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000
-				  0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000
-				  0x02000000 0 0x30000000 0 0x30000000 0 0x08000000
-				  0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000>,
+				 <0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000>,
+				 <0x02000000 0 0x30000000 0 0x30000000 0 0x08000000>,
+				 <0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
 			/* Map all possible DDR as inbound ranges */
-			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000
-				      0x43000000 1 0x80000000 1 0x80000000 0 0x80000000>;
+			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000>,
+				     <0x43000000 1 0x80000000 1 0x80000000 0 0x80000000>;
 			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
@@ -1716,6 +1809,8 @@
 			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 				 <&cpg CPG_MOD 722>;
 			clock-names = "du.0", "du.1", "du.2";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/renesas/r8a7791-koelsch.dts
index af6bd8fcd5a4..e9c13bb03772 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/renesas/r8a7791-koelsch.dts
@@ -53,6 +53,9 @@
 		i2c12 = &i2cexio1;
 		i2c13 = &i2chdmi;
 		i2c14 = &i2cexio4;
+		mmc0 = &sdhi0;
+		mmc1 = &sdhi1;
+		mmc2 = &sdhi2;
 	};
 
 	chosen {
@@ -70,14 +73,12 @@
 		reg = <2 0x00000000 0 0x40000000>;
 	};
 
-	lbsc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-	};
-
 	keyboard {
 		compatible = "gpio-keys";
 
+		pinctrl-0 = <&keyboard_pins>;
+		pinctrl-names = "default";
+
 		key-1 {
 			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_1>;
@@ -173,6 +174,24 @@
 		};
 	};
 
+	reg_1p8v: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	vcc_sdhi0: regulator-vcc-sdhi0 {
 		compatible = "regulator-fixed";
 
@@ -193,8 +212,7 @@
 
 		gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi1: regulator-vcc-sdhi1 {
@@ -217,8 +235,7 @@
 
 		gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi2: regulator-vcc-sdhi2 {
@@ -241,8 +258,7 @@
 
 		gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	audio_clock: audio_clock {
@@ -342,7 +358,7 @@
 	 * I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
 	 * A fallback to GPIO is provided.
 	 */
-	i2cexio1: i2c-12 {
+	i2cexio1: i2c-mux1 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c1>, <&gpioi2c1>;
 		i2c-bus-name = "i2c-exio1";
@@ -353,7 +369,7 @@
 	/*
 	 * A fallback to GPIO is provided for I2C2.
 	 */
-	i2chdmi: i2c-13 {
+	i2chdmi: i2c-mux2 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c2>, <&gpioi2c2>;
 		i2c-bus-name = "i2c-hdmi";
@@ -369,7 +385,6 @@
 		composite-in@20 {
 			compatible = "adi,adv7180";
 			reg = <0x20>;
-			remote = <&vin1>;
 
 			port {
 				adv7180: endpoint {
@@ -387,11 +402,15 @@
 			clocks = <&cec_clock>;
 			clock-names = "cec";
 
+			avdd-supply = <&reg_1p8v>;
+			dvdd-supply = <&reg_1p8v>;
+			pvdd-supply = <&reg_1p8v>;
+			dvdd-3v-supply = <&reg_3p3v>;
+			bgvdd-supply = <&reg_1p8v>;
+
 			adi,input-depth = <8>;
 			adi,input-colorspace = "rgb";
 			adi,input-clock = "1x";
-			adi,input-style = <1>;
-			adi,input-justification = "evenly";
 
 			ports {
 				#address-cells = <1>;
@@ -451,7 +470,7 @@
 	 * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
 	 * A fallback to GPIO is provided.
 	 */
-	i2cexio4: i2c-14 {
+	i2cexio4: i2c-mux3 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c4>, <&gpioi2c4>;
 		i2c-bus-name = "i2c-exio4";
@@ -621,10 +640,15 @@
 		groups = "audio_clk_a";
 		function = "audio_clk";
 	};
+
+	keyboard_pins: keyboard {
+		pins = "GP_5_0", "GP_5_1", "GP_5_2", "GP_5_3";
+		bias-pull-up;
+	};
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -632,10 +656,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -797,7 +824,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
@@ -883,7 +910,7 @@
 };
 
 &rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
 	pinctrl-names = "default";
 
 	/* Single DAI */
@@ -893,8 +920,8 @@
 
 	rcar_sound,dai {
 		dai0 {
-			playback = <&ssi0 &src2 &dvc0>;
-			capture  = <&ssi1 &src3 &dvc1>;
+			playback = <&ssi0>, <&src2>, <&dvc0>;
+			capture  = <&ssi1>, <&src3>, <&dvc1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/renesas/r8a7791-porter.dts
index d6cf16aac14d..7e8bc06715f6 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/renesas/r8a7791-porter.dts
@@ -28,6 +28,8 @@
 		serial0 = &scif0;
 		i2c9 = &gpioi2c2;
 		i2c10 = &i2chdmi;
+		mmc0 = &sdhi0;
+		mmc1 = &sdhi2;
 	};
 
 	chosen {
@@ -45,6 +47,24 @@
 		reg = <2 0x00000000 0 0x40000000>;
 	};
 
+	reg_1p8v: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	vcc_sdhi0: regulator-vcc-sdhi0 {
 		compatible = "regulator-fixed";
 
@@ -63,8 +83,7 @@
 
 		gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi2: regulator-vcc-sdhi2 {
@@ -85,8 +104,7 @@
 
 		gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	hdmi-out {
@@ -148,7 +166,7 @@
 	/*
 	 * A fallback to GPIO is provided for I2C2.
 	 */
-	i2chdmi: i2c-10 {
+	i2chdmi: i2c-mux1 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c2>, <&gpioi2c2>;
 		i2c-bus-name = "i2c-hdmi";
@@ -164,7 +182,6 @@
 		composite-in@20 {
 			compatible = "adi,adv7180";
 			reg = <0x20>;
-			remote = <&vin0>;
 
 			port {
 				adv7180: endpoint {
@@ -180,11 +197,15 @@
 			interrupt-parent = <&gpio3>;
 			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 
+			avdd-supply = <&reg_1p8v>;
+			dvdd-supply = <&reg_1p8v>;
+			pvdd-supply = <&reg_1p8v>;
+			dvdd-3v-supply = <&reg_3p3v>;
+			bgvdd-supply = <&reg_1p8v>;
+
 			adi,input-depth = <8>;
 			adi,input-colorspace = "rgb";
 			adi,input-clock = "1x";
-			adi,input-style = <1>;
-			adi,input-justification = "evenly";
 
 			ports {
 				#address-cells = <1>;
@@ -297,7 +318,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -305,10 +326,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -390,7 +414,7 @@
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
@@ -498,7 +522,7 @@
 };
 
 &rcar_sound {
-	pinctrl-0 = <&ssi_pins &audio_clk_pins>;
+	pinctrl-0 = <&ssi_pins>, <&audio_clk_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/renesas/r8a7791.dtsi
index 6f875502453c..b9d34147628e 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7791.dtsi
@@ -68,7 +68,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -77,6 +76,7 @@
 			clock-frequency = <1500000000>;
 			clocks = <&cpg CPG_CORE R8A7791_CLK_Z>;
 			power-domains = <&sysc R8A7791_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 			voltage-tolerance = <1>; /* 1% */
 			clock-latency = <300000>; /* 300 us */
@@ -97,6 +97,7 @@
 			clock-frequency = <1500000000>;
 			clocks = <&cpg CPG_CORE R8A7791_CLK_Z>;
 			power-domains = <&sysc R8A7791_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 			voltage-tolerance = <1>; /* 1% */
 			clock-latency = <300000>; /* 300 us */
@@ -160,6 +161,7 @@
 			compatible = "renesas,r8a7791-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -286,11 +288,22 @@
 			resets = <&cpg 904>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7791";
 			reg = <0 0xe6060000 0 0x250>;
 		};
 
+		tpu: pwm@e60f0000 {
+			compatible = "renesas,tpu-r8a7791", "renesas,tpu";
+			reg = <0 0xe60f0000 0 0x148>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 304>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 304>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		cpg: clock-controller@e6150000 {
 			compatible = "renesas,r8a7791-cpg-mssr";
 			reg = <0 0xe6150000 0 0x1000>;
@@ -304,7 +317,7 @@
 		apmu@e6152000 {
 			compatible = "renesas,r8a7791-apmu", "renesas,apmu";
 			reg = <0 0xe6152000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -350,7 +363,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -360,7 +373,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -369,7 +382,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -379,7 +392,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -388,7 +401,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -398,7 +411,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_rt: mmu@ffc80000 {
+		ipmmu_rt: iommu@ffc80000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xffc80000 0 0x1000>;
@@ -407,7 +420,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_gp: mmu@e62a0000 {
+		ipmmu_gp: iommu@e62a0000 {
 			compatible = "renesas,ipmmu-r8a7791",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe62a0000 0 0x1000>;
@@ -420,6 +433,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -592,7 +608,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7791",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -604,11 +620,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
@@ -618,8 +634,8 @@
 			compatible = "renesas,r8a7791-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65a0000 0 0x100>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 330>;
 			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
@@ -632,8 +648,8 @@
 			compatible = "renesas,r8a7791-usb-dmac",
 				     "renesas,usb-dmac";
 			reg = <0 0xe65b0000 0 0x100>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "ch0", "ch1";
 			clocks = <&cpg CPG_MOD 331>;
 			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
@@ -646,22 +662,22 @@
 			compatible = "renesas,dmac-r8a7791",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -679,22 +695,22 @@
 			compatible = "renesas,dmac-r8a7791",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -714,6 +730,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -1064,6 +1081,76 @@
 			status = "disabled";
 		};
 
+		pwm0: pwm@e6e30000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e30000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@e6e31000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e31000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm2: pwm@e6e32000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e32000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm3: pwm@e6e33000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e33000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm4: pwm@e6e34000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e34000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm5: pwm@e6e35000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e35000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		pwm6: pwm@e6e36000 {
+			compatible = "renesas,pwm-r8a7791", "renesas,pwm-rcar";
+			reg = <0 0xe6e36000 0 0x8>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
 		adc: adc@e6e54000 {
 			compatible = "renesas,r8a7791-gyroadc",
 				     "renesas,rcar-gyroadc";
@@ -1136,7 +1223,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -1278,7 +1365,7 @@
 					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi1: ssi-1 {
-					 interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
 					dmas = <&audma0 0x03>, <&audma1 0x04>,
 					       <&audma0 0x49>, <&audma1 0x4a>;
 					dma-names = "rx", "tx", "rxu", "txu";
@@ -1338,20 +1425,20 @@
 			compatible = "renesas,dmac-r8a7791",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1369,20 +1456,20 @@
 			compatible = "renesas,dmac-r8a7791",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec720000 0 0x10000>;
-			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1426,10 +1513,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x800 0 0 0 0>;
@@ -1461,10 +1548,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x10800 0 0 0 0>;
@@ -1479,7 +1566,7 @@
 			};
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7791",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1494,7 +1581,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee140000 {
+		sdhi1: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7791",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1509,7 +1596,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7791",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1598,13 +1685,13 @@
 			#size-cells = <2>;
 			bus-range = <0x00 0xff>;
 			device_type = "pci";
-			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000
-				  0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000
-				  0x02000000 0 0x30000000 0 0x30000000 0 0x08000000
-				  0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+			ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000>,
+				 <0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000>,
+				 <0x02000000 0 0x30000000 0 0x30000000 0 0x08000000>,
+				 <0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
 			/* Map all possible DDR as inbound ranges */
-			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000
-				      0x43000000 2 0x00000000 2 0x00000000 1 0x00000000>;
+			dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x80000000>,
+				     <0x43000000 2 0x00000000 2 0x00000000 1 0x00000000>;
 			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
@@ -1678,9 +1765,10 @@
 			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/renesas/r8a7792-blanche.dts
index 248eb717eb35..4f9838cf97ee 100644
--- a/arch/arm/boot/dts/r8a7792-blanche.dts
+++ b/arch/arm/boot/dts/renesas/r8a7792-blanche.dts
@@ -30,6 +30,15 @@
 		reg = <0 0x40000000 0 0x40000000>;
 	};
 
+	d1_8v: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "D1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	d3_3v: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "D3.3V";
@@ -39,21 +48,6 @@
 		regulator-always-on;
 	};
 
-	ethernet@18000000 {
-		compatible = "smsc,lan89218", "smsc,lan9115";
-		reg = <0 0x18000000 0 0x100>;
-		phy-mode = "mii";
-		interrupt-parent = <&irqc>;
-		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
-		smsc,irq-push-pull;
-		reg-io-width = <4>;
-		vddvario-supply = <&d3_3v>;
-		vdd33a-supply = <&d3_3v>;
-
-		pinctrl-0 = <&lan89218_pins>;
-		pinctrl-names = "default";
-	};
-
 	vga-encoder {
 		compatible = "adi,adv7123";
 
@@ -112,6 +106,9 @@
 	keyboard {
 		compatible = "gpio-keys";
 
+		pinctrl-0 = <&keyboard_pins>;
+		pinctrl-names = "default";
+
 		key-1 {
 			linux,code = <KEY_1>;
 			label = "SW2-1";
@@ -193,6 +190,52 @@
 	clock-frequency = <48000000>;
 };
 
+&lbsc {
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0x00000000 0x04000000>;
+		pinctrl-0 = <&flash_pins>;
+		pinctrl-names = "default";
+		bank-width = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition@40000 {
+				label = "uboot-env";
+				reg = <0x00040000 0x00040000>;
+				read-only;
+			};
+			partition@80000 {
+				label = "flash";
+				reg = <0x00080000 0x03f80000>;
+			};
+		};
+	};
+
+	ethernet@18000000 {
+		compatible = "smsc,lan89218", "smsc,lan9115";
+		reg = <0x18000000 0x100>;
+		phy-mode = "mii";
+		interrupt-parent = <&irqc>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		smsc,irq-push-pull;
+		reg-io-width = <4>;
+		vddvario-supply = <&d3_3v>;
+		vdd33a-supply = <&d3_3v>;
+
+		pinctrl-0 = <&lan89218_pins>;
+		pinctrl-names = "default";
+	};
+};
+
 &pfc {
 	scif0_pins: scif0 {
 		groups = "scif0_data";
@@ -235,6 +278,16 @@
 		function = "du1";
 	};
 
+	flash_pins: flash {
+		groups = "lbsc_cs0";
+		function = "lbsc";
+	};
+
+	keyboard_pins: keyboard {
+		pins = "GP_3_10", "GP_3_11", "GP_3_12", "GP_3_15", "GP_11_2";
+		bias-pull-up;
+	};
+
 	pmic_irq_pins: pmicirq {
 		groups = "intc_irq2";
 		function = "intc";
@@ -286,11 +339,15 @@
 		interrupt-parent = <&irqc>;
 		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
 
+		avdd-supply = <&d1_8v>;
+		dvdd-supply = <&d1_8v>;
+		pvdd-supply = <&d1_8v>;
+		dvdd-3v-supply = <&d3_3v>;
+		bgvdd-supply = <&d1_8v>;
+
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
@@ -329,14 +386,14 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
 };
 
 &du {
-	pinctrl-0 = <&du0_pins &du1_pins>;
+	pinctrl-0 = <&du0_pins>, <&du1_pins>;
 	pinctrl-names = "default";
 
 	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&x1_clk>, <&x2_clk>;
diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts b/arch/arm/boot/dts/renesas/r8a7792-wheat.dts
index bd2a63bdab3d..000f21a2a863 100644
--- a/arch/arm/boot/dts/r8a7792-wheat.dts
+++ b/arch/arm/boot/dts/renesas/r8a7792-wheat.dts
@@ -29,6 +29,15 @@
 		reg = <0 0x40000000 0 0x40000000>;
 	};
 
+	d1_8v: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "D1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	d3_3v: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "D3.3V";
@@ -38,22 +47,6 @@
 		regulator-always-on;
 	};
 
-	ethernet@18000000 {
-		compatible = "smsc,lan89218", "smsc,lan9115";
-		reg = <0 0x18000000 0 0x100>;
-		phy-mode = "mii";
-		interrupt-parent = <&irqc>;
-		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
-		smsc,irq-push-pull;
-		smsc,save-mac-address;
-		reg-io-width = <4>;
-		vddvario-supply = <&d3_3v>;
-		vdd33a-supply = <&d3_3v>;
-
-		pinctrl-0 = <&lan89218_pins>;
-		pinctrl-names = "default";
-	};
-
 	keyboard {
 		compatible = "gpio-keys";
 
@@ -117,6 +110,24 @@
 	clock-frequency = <20000000>;
 };
 
+&lbsc {
+	ethernet@18000000 {
+		compatible = "smsc,lan89218", "smsc,lan9115";
+		reg = <0x18000000 0x100>;
+		phy-mode = "mii";
+		interrupt-parent = <&irqc>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		smsc,irq-push-pull;
+		smsc,save-mac-address;
+		reg-io-width = <4>;
+		vddvario-supply = <&d3_3v>;
+		vdd33a-supply = <&d3_3v>;
+
+		pinctrl-0 = <&lan89218_pins>;
+		pinctrl-names = "default";
+	};
+};
+
 &pfc {
 	scif0_pins: scif0 {
 		groups = "scif0_data";
@@ -249,14 +260,18 @@
 	 */
 	hdmi@3d {
 		compatible = "adi,adv7513";
-		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
-		reg-names = "main", "cec", "edid", "packet";
+		reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
+		reg-names = "main", "edid", "cec", "packet";
+
+		avdd-supply = <&d1_8v>;
+		dvdd-supply = <&d1_8v>;
+		pvdd-supply = <&d1_8v>;
+		dvdd-3v-supply = <&d3_3v>;
+		bgvdd-supply = <&d1_8v>;
 
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
@@ -280,14 +295,18 @@
 
 	hdmi@39 {
 		compatible = "adi,adv7513";
-		reg = <0x39>, <0x29>, <0x49>, <0x59>;
-		reg-names = "main", "cec", "edid", "packet";
+		reg = <0x39>, <0x49>, <0x29>, <0x59>;
+		reg-names = "main", "edid", "cec", "packet";
+
+		avdd-supply = <&d1_8v>;
+		dvdd-supply = <&d1_8v>;
+		pvdd-supply = <&d1_8v>;
+		dvdd-3v-supply = <&d3_3v>;
+		bgvdd-supply = <&d1_8v>;
 
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";
-		adi,input-style = <1>;
-		adi,input-justification = "evenly";
 
 		ports {
 			#address-cells = <1>;
@@ -311,7 +330,7 @@
 };
 
 &du {
-	pinctrl-0 = <&du0_pins &du1_pins>;
+	pinctrl-0 = <&du0_pins>, <&du1_pins>;
 	pinctrl-names = "default";
 
 	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&osc2_clk>;
diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/renesas/r8a7792.dtsi
index c4ea2d676030..ecfab3ff59e8 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7792.dtsi
@@ -45,7 +45,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -54,6 +53,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A7792_CLK_Z>;
 			power-domains = <&sysc R8A7792_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 		};
 
@@ -64,6 +64,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A7792_CLK_Z>;
 			power-domains = <&sysc R8A7792_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA15>;
 		};
 
@@ -83,6 +84,13 @@
 		clock-frequency = <0>;
 	};
 
+	lbsc: lbsc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x1c000000>;
+	};
+
 	pmu {
 		compatible = "arm,cortex-a15-pmu";
 		interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
@@ -110,6 +118,7 @@
 			compatible = "renesas,r8a7792-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -296,7 +305,7 @@
 			resets = <&cpg 913>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7792";
 			reg = <0 0xe6060000 0 0x144>;
 		};
@@ -314,7 +323,7 @@
 		apmu@e6152000 {
 			compatible = "renesas,r8a7792-apmu", "renesas,apmu";
 			reg = <0 0xe6152000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -345,6 +354,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -466,22 +478,22 @@
 			compatible = "renesas,dmac-r8a7792",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -499,22 +511,22 @@
 			compatible = "renesas,dmac-r8a7792",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -534,6 +546,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -777,7 +790,7 @@
 			status = "disabled";
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7792",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -849,9 +862,10 @@
 			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/renesas/r8a7793-gose.dts
index 48fbeb6340fd..1744fdbf9e0c 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/renesas/r8a7793-gose.dts
@@ -49,6 +49,9 @@
 		i2c10 = &gpioi2c4;
 		i2c11 = &i2chdmi;
 		i2c12 = &i2cexio4;
+		mmc0 = &sdhi0;
+		mmc1 = &sdhi1;
+		mmc2 = &sdhi2;
 	};
 
 	chosen {
@@ -61,9 +64,12 @@
 		reg = <0 0x40000000 0 0x40000000>;
 	};
 
-	gpio-keys {
+	keyboard {
 		compatible = "gpio-keys";
 
+		pinctrl-0 = <&keyboard_pins>;
+		pinctrl-names = "default";
+
 		key-1 {
 			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_1>;
@@ -159,6 +165,24 @@
 		};
 	};
 
+	reg_1p8v: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	vcc_sdhi0: regulator-vcc-sdhi0 {
 		compatible = "regulator-fixed";
 
@@ -179,8 +203,7 @@
 
 		gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi1: regulator-vcc-sdhi1 {
@@ -203,8 +226,7 @@
 
 		gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi2: regulator-vcc-sdhi2 {
@@ -227,8 +249,7 @@
 
 		gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	audio_clock: audio_clock {
@@ -321,7 +342,7 @@
 	/*
 	 * A fallback to GPIO is provided for I2C2.
 	 */
-	i2chdmi: i2c-11 {
+	i2chdmi: i2c-mux1 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c2>, <&gpioi2c2>;
 		i2c-bus-name = "i2c-hdmi";
@@ -337,9 +358,8 @@
 		composite-in@20 {
 			compatible = "adi,adv7180cp";
 			reg = <0x20>;
-			remote = <&vin1>;
 
-			port {
+			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -366,11 +386,15 @@
 			interrupt-parent = <&gpio3>;
 			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 
+			avdd-supply = <&reg_1p8v>;
+			dvdd-supply = <&reg_1p8v>;
+			pvdd-supply = <&reg_1p8v>;
+			dvdd-3v-supply = <&reg_3p3v>;
+			bgvdd-supply = <&reg_1p8v>;
+
 			adi,input-depth = <8>;
 			adi,input-colorspace = "rgb";
 			adi,input-clock = "1x";
-			adi,input-style = <1>;
-			adi,input-justification = "evenly";
 
 			ports {
 				#address-cells = <1>;
@@ -399,7 +423,7 @@
 			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 			default-input = <0>;
 
-			port {
+			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -430,7 +454,7 @@
 	 * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
 	 * A fallback to GPIO is provided.
 	 */
-	i2cexio4: i2c-12 {
+	i2cexio4: i2c-mux2 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c4>, <&gpioi2c4>;
 		i2c-bus-name = "i2c-exio4";
@@ -570,6 +594,11 @@
 		function = "audio_clk";
 	};
 
+	keyboard_pins: keyboard {
+		pins = "GP_5_0", "GP_5_1", "GP_5_2", "GP_5_3";
+		bias-pull-up;
+	};
+
 	vin0_pins: vin0 {
 		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
 		function = "vin0";
@@ -582,7 +611,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -590,10 +619,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -732,7 +764,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
@@ -756,7 +788,7 @@
 };
 
 &rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
 	pinctrl-names = "default";
 
 	/* Single DAI */
@@ -766,8 +798,8 @@
 
 	rcar_sound,dai {
 		dai0 {
-			playback = <&ssi0 &src2 &dvc0>;
-			capture  = <&ssi1 &src3 &dvc1>;
+			playback = <&ssi0>, <&src2>, <&dvc0>;
+			capture  = <&ssi1>, <&src3>, <&dvc1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/renesas/r8a7793.dtsi
index bf05110fac4e..f51bf687f4bd 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7793.dtsi
@@ -60,7 +60,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -69,6 +68,7 @@
 			clock-frequency = <1500000000>;
 			clocks = <&cpg CPG_CORE R8A7793_CLK_Z>;
 			power-domains = <&sysc R8A7793_PD_CA15_CPU0>;
+			enable-method = "renesas,apmu";
 			voltage-tolerance = <1>; /* 1% */
 			clock-latency = <300000>; /* 300 us */
 
@@ -89,6 +89,7 @@
 			clock-frequency = <1500000000>;
 			clocks = <&cpg CPG_CORE R8A7793_CLK_Z>;
 			power-domains = <&sysc R8A7793_PD_CA15_CPU1>;
+			enable-method = "renesas,apmu";
 			voltage-tolerance = <1>; /* 1% */
 			clock-latency = <300000>; /* 300 us */
 
@@ -145,6 +146,7 @@
 			compatible = "renesas,r8a7793-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -271,7 +273,7 @@
 			resets = <&cpg 904>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7793";
 			reg = <0 0xe6060000 0 0x250>;
 		};
@@ -290,7 +292,7 @@
 		apmu@e6152000 {
 			compatible = "renesas,r8a7793-apmu", "renesas,apmu";
 			reg = <0 0xe6152000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -336,7 +338,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -346,7 +348,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -355,7 +357,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -365,7 +367,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -374,7 +376,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -384,7 +386,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_rt: mmu@ffc80000 {
+		ipmmu_rt: iommu@ffc80000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xffc80000 0 0x1000>;
@@ -393,7 +395,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_gp: mmu@e62a0000 {
+		ipmmu_gp: iommu@e62a0000 {
 			compatible = "renesas,ipmmu-r8a7793",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe62a0000 0 0x1000>;
@@ -406,6 +408,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -565,22 +570,22 @@
 			compatible = "renesas,dmac-r8a7793",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -598,22 +603,22 @@
 			compatible = "renesas,dmac-r8a7793",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -983,7 +988,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -1106,7 +1111,7 @@
 					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi1: ssi-1 {
-					 interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
 					dmas = <&audma0 0x03>, <&audma1 0x04>,
 					       <&audma0 0x49>, <&audma1 0x4a>;
 					dma-names = "rx", "tx", "rxu", "txu";
@@ -1166,20 +1171,20 @@
 			compatible = "renesas,dmac-r8a7793",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1197,20 +1202,20 @@
 			compatible = "renesas,dmac-r8a7793",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec720000 0 0x10000>;
-			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -1224,7 +1229,7 @@
 			dma-channels = <13>;
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7793",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1239,7 +1244,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee140000 {
+		sdhi1: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7793",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1254,7 +1259,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7793",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1338,9 +1343,10 @@
 			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>;
+			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/renesas/r8a7794-alt.dts
index 1d22fcdc5d22..c0d067df22a0 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/renesas/r8a7794-alt.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 #include "r8a7794.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Alt";
@@ -19,6 +20,9 @@
 		i2c10 = &gpioi2c4;
 		i2c11 = &i2chdmi;
 		i2c12 = &i2cexio4;
+		mmc0 = &mmcif0;
+		mmc1 = &sdhi0;
+		mmc2 = &sdhi1;
 	};
 
 	chosen {
@@ -60,8 +64,7 @@
 
 		gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vcc_sdhi1: regulator-vcc-sdhi1 {
@@ -84,13 +87,43 @@
 
 		gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
-	lbsc {
-		#address-cells = <1>;
-		#size-cells = <1>;
+	keyboard {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keyboard_pins>;
+		pinctrl-names = "default";
+
+		one {
+			linux,code = <KEY_1>;
+			label = "SW2-1";
+			wakeup-source;
+			debounce-interval = <20>;
+			gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+		};
+		two {
+			linux,code = <KEY_2>;
+			label = "SW2-2";
+			wakeup-source;
+			debounce-interval = <20>;
+			gpios = <&gpio3 10 GPIO_ACTIVE_LOW>;
+		};
+		three {
+			linux,code = <KEY_3>;
+			label = "SW2-3";
+			wakeup-source;
+			debounce-interval = <20>;
+			gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
+		};
+		four {
+			linux,code = <KEY_4>;
+			label = "SW2-4";
+			wakeup-source;
+			debounce-interval = <20>;
+			gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+		};
 	};
 
 	vga-encoder {
@@ -159,7 +192,7 @@
 	/*
 	 * A fallback to GPIO is provided for I2C1.
 	 */
-	i2chdmi: i2c-11 {
+	i2chdmi: i2c-mux1 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c1>, <&gpioi2c1>;
 		i2c-bus-name = "i2c-hdmi";
@@ -169,7 +202,6 @@
 		composite-in@20 {
 			compatible = "adi,adv7180";
 			reg = <0x20>;
-			remote = <&vin0>;
 
 			port {
 				adv7180: endpoint {
@@ -190,7 +222,7 @@
 	 * I2C4 is routed to EXIO connector B, pins 73 (SCL) + 74 (SDA).
 	 * A fallback to GPIO is provided.
 	 */
-	i2cexio4: i2c-14 {
+	i2cexio4: i2c-mux2 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c4>, <&gpioi2c4>;
 		i2c-bus-name = "i2c-exio4";
@@ -319,6 +351,11 @@
 		groups = "usb1";
 		function = "usb1";
 	};
+
+	keyboard_pins: keyboard {
+		pins = "GP_3_9", "GP_3_10", "GP_3_11", "GP_3_12";
+		bias-pull-up;
+	};
 };
 
 &cmt0 {
@@ -333,7 +370,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -341,10 +378,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -418,7 +458,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/renesas/r8a7794-silk.dts
index b3177aea45d1..43d480a7f3ea 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/renesas/r8a7794-silk.dts
@@ -31,6 +31,8 @@
 		serial0 = &scif2;
 		i2c9 = &gpioi2c1;
 		i2c10 = &i2chdmi;
+		mmc0 = &mmcif0;
+		mmc1 = &sdhi1;
 	};
 
 	chosen {
@@ -43,9 +45,12 @@
 		reg = <0 0x40000000 0 0x40000000>;
 	};
 
-	gpio-keys {
+	keyboard {
 		compatible = "gpio-keys";
 
+		pinctrl-0 = <&keyboard_pins>;
+		pinctrl-names = "default";
+
 		key-3 {
 			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_3>;
@@ -97,6 +102,15 @@
 		};
 	};
 
+	d1_8v: regulator-d1-8v {
+		compatible = "regulator-fixed";
+		regulator-name = "D1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	d3_3v: regulator-d3-3v {
 		compatible = "regulator-fixed";
 		regulator-name = "D3.3V";
@@ -126,8 +140,7 @@
 
 		gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
+		states = <3300000 1>, <1800000 0>;
 	};
 
 	vga-encoder {
@@ -221,7 +234,7 @@
 	/*
 	 * A fallback to GPIO is provided for I2C1.
 	 */
-	i2chdmi: i2c-10 {
+	i2chdmi: i2c-mux1 {
 		compatible = "i2c-demux-pinctrl";
 		i2c-parent = <&i2c1>, <&gpioi2c1>;
 		i2c-bus-name = "i2c-hdmi";
@@ -237,7 +250,6 @@
 		composite-in@20 {
 			compatible = "adi,adv7180";
 			reg = <0x20>;
-			remote = <&vin0>;
 
 			port {
 				adv7180: endpoint {
@@ -253,11 +265,15 @@
 			interrupt-parent = <&gpio5>;
 			interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 
+			avdd-supply = <&d1_8v>;
+			dvdd-supply = <&d1_8v>;
+			pvdd-supply = <&d1_8v>;
+			dvdd-3v-supply = <&d3_3v>;
+			bgvdd-supply = <&d1_8v>;
+
 			adi,input-depth = <8>;
 			adi,input-colorspace = "rgb";
 			adi,input-clock = "1x";
-			adi,input-style = <1>;
-			adi,input-justification = "evenly";
 
 			ports {
 				#address-cells = <1>;
@@ -360,6 +376,11 @@
 		function = "du1";
 	};
 
+	keyboard_pins: keyboard {
+		pins = "GP_3_9", "GP_3_10", "GP_3_11", "GP_3_12";
+		bias-pull-up;
+	};
+
 	ssi_pins: sound {
 		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
 		function = "ssi";
@@ -383,7 +404,7 @@
 };
 
 &ether {
-	pinctrl-0 = <&ether_pins &phy1_pins>;
+	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
 	pinctrl-names = "default";
 
 	phy-handle = <&phy1>;
@@ -391,10 +412,13 @@
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0022.1537",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		interrupt-parent = <&irqc0>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		micrel,led-mode = <1>;
+		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -424,7 +448,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
@@ -521,7 +545,7 @@
 };
 
 &du {
-	pinctrl-0 = <&du0_pins &du1_pins>;
+	pinctrl-0 = <&du0_pins>, <&du1_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 
@@ -544,7 +568,7 @@
 };
 
 &rcar_sound {
-	pinctrl-0 = <&ssi_pins &audio_clk_pins>;
+	pinctrl-0 = <&ssi_pins>, <&audio_clk_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/renesas/r8a7794.dtsi
index 8d797d34816e..371dd4715dde 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a7794.dtsi
@@ -62,7 +62,6 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		enable-method = "renesas,apmu";
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -71,6 +70,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A7794_CLK_Z2>;
 			power-domains = <&sysc R8A7794_PD_CA7_CPU0>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 		};
 
@@ -81,6 +81,7 @@
 			clock-frequency = <1000000000>;
 			clocks = <&cpg CPG_CORE R8A7794_CLK_Z2>;
 			power-domains = <&sysc R8A7794_PD_CA7_CPU1>;
+			enable-method = "renesas,apmu";
 			next-level-cache = <&L2_CA7>;
 		};
 
@@ -127,6 +128,7 @@
 			compatible = "renesas,r8a7794-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -238,7 +240,7 @@
 			resets = <&cpg 905>;
 		};
 
-		pfc: pin-controller@e6060000 {
+		pfc: pinctrl@e6060000 {
 			compatible = "renesas,pfc-r8a7794";
 			reg = <0 0xe6060000 0 0x11c>;
 		};
@@ -256,7 +258,7 @@
 		apmu@e6151000 {
 			compatible = "renesas,r8a7794-apmu", "renesas,apmu";
 			reg = <0 0xe6151000 0 0x188>;
-			cpus = <&cpu0 &cpu1>;
+			cpus = <&cpu0>, <&cpu1>;
 		};
 
 		rst: reset-controller@e6160000 {
@@ -290,7 +292,7 @@
 			resets = <&cpg 407>;
 		};
 
-		ipmmu_sy0: mmu@e6280000 {
+		ipmmu_sy0: iommu@e6280000 {
 			compatible = "renesas,ipmmu-r8a7794",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6280000 0 0x1000>;
@@ -300,7 +302,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_sy1: mmu@e6290000 {
+		ipmmu_sy1: iommu@e6290000 {
 			compatible = "renesas,ipmmu-r8a7794",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6290000 0 0x1000>;
@@ -309,7 +311,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_ds: mmu@e6740000 {
+		ipmmu_ds: iommu@e6740000 {
 			compatible = "renesas,ipmmu-r8a7794",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe6740000 0 0x1000>;
@@ -319,7 +321,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mp: mmu@ec680000 {
+		ipmmu_mp: iommu@ec680000 {
 			compatible = "renesas,ipmmu-r8a7794",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xec680000 0 0x1000>;
@@ -328,7 +330,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_mx: mmu@fe951000 {
+		ipmmu_mx: iommu@fe951000 {
 			compatible = "renesas,ipmmu-r8a7794",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xfe951000 0 0x1000>;
@@ -338,7 +340,7 @@
 			status = "disabled";
 		};
 
-		ipmmu_gp: mmu@e62a0000 {
+		ipmmu_gp: iommu@e62a0000 {
 			compatible = "renesas,ipmmu-r8a7794",
 				     "renesas,ipmmu-vmsa";
 			reg = <0 0xe62a0000 0 0x1000>;
@@ -351,6 +353,9 @@
 		icram0:	sram@e63a0000 {
 			compatible = "mmio-sram";
 			reg = <0 0xe63a0000 0 0x12000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xe63a0000 0x12000>;
 		};
 
 		icram1:	sram@e63c0000 {
@@ -501,7 +506,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7794",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -513,11 +518,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
@@ -527,22 +532,22 @@
 			compatible = "renesas,dmac-r8a7794",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6700000 0 0x20000>;
-			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -560,22 +565,22 @@
 			compatible = "renesas,dmac-r8a7794",
 				     "renesas,rcar-dmac";
 			reg = <0 0xe6720000 0 0x20000>;
-			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3",
 					  "ch4", "ch5", "ch6", "ch7",
@@ -595,6 +600,7 @@
 			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 812>;
+			clock-names = "fck";
 			power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			#address-cells = <1>;
@@ -949,7 +955,7 @@
 
 		rcar_sound: sound@ec500000 {
 			/*
-			 * #sound-dai-cells is required
+			 * #sound-dai-cells is required if simple-card
 			 *
 			 * Single DAI : #sound-dai-cells = <0>;         <&rcar_sound>;
 			 * Multi  DAI : #sound-dai-cells = <1>;         <&rcar_sound N>;
@@ -1132,20 +1138,20 @@
 			compatible = "renesas,dmac-r8a7794",
 				     "renesas,rcar-dmac";
 			reg = <0 0xec700000 0 0x10000>;
-			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "error",
 					  "ch0", "ch1", "ch2", "ch3", "ch4",
 					  "ch5", "ch6", "ch7", "ch8", "ch9",
@@ -1176,10 +1182,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x800 0 0 0 0>;
@@ -1211,10 +1217,10 @@
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
 			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
-			interrupt-map-mask = <0xff00 0 0 0x7>;
-			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 
 			usb@1,0 {
 				reg = <0x10800 0 0 0 0>;
@@ -1229,7 +1235,7 @@
 			};
 		};
 
-		sdhi0: sd@ee100000 {
+		sdhi0: mmc@ee100000 {
 			compatible = "renesas,sdhi-r8a7794",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee100000 0 0x328>;
@@ -1244,7 +1250,7 @@
 			status = "disabled";
 		};
 
-		sdhi1: sd@ee140000 {
+		sdhi1: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a7794",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee140000 0 0x100>;
@@ -1259,7 +1265,7 @@
 			status = "disabled";
 		};
 
-		sdhi2: sd@ee160000 {
+		sdhi2: mmc@ee160000 {
 			compatible = "renesas,sdhi-r8a7794",
 				     "renesas,rcar-gen2-sdhi";
 			reg = <0 0xee160000 0 0x100>;
@@ -1353,6 +1359,8 @@
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>;
 			clock-names = "du.0", "du.1";
+			resets = <&cpg 724>;
+			reset-names = "du.0";
 			status = "disabled";
 
 			ports {
diff --git a/arch/arm/boot/dts/r8a77xx-aa121td01-panel.dtsi b/arch/arm/boot/dts/renesas/r8a77xx-aa121td01-panel.dtsi
index 6e7589ea7562..6e7589ea7562 100644
--- a/arch/arm/boot/dts/r8a77xx-aa121td01-panel.dtsi
+++ b/arch/arm/boot/dts/renesas/r8a77xx-aa121td01-panel.dtsi
diff --git a/arch/arm/boot/dts/renesas/r9a06g032-rzn1d400-db.dts b/arch/arm/boot/dts/renesas/r9a06g032-rzn1d400-db.dts
new file mode 100644
index 000000000000..31cdca3e623c
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r9a06g032-rzn1d400-db.dts
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the RZN1D-DB Board
+ *
+ * Copyright (C) 2018 Renesas Electronics Europe Limited
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/rzn1-pinctrl.h>
+#include <dt-bindings/net/pcs-rzn1-miic.h>
+
+#include "r9a06g032.dtsi"
+
+/ {
+	model = "RZN1D-DB Board";
+	compatible = "renesas,rzn1d400-db", "renesas,r9a06g032";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+};
+
+&can0 {
+	pinctrl-0 = <&pins_can0>;
+	pinctrl-names = "default";
+
+	/* Assuming CN10/CN11 are wired for CAN1 */
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-0 = <&pins_can1>;
+	pinctrl-names = "default";
+
+	/* Please only enable can0 or can1, depending on CN10/CN11 */
+	/* status = "okay"; */
+};
+
+&eth_miic {
+	status = "okay";
+	renesas,miic-switch-portin = <MIIC_GMAC2_PORT>;
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "gmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&mii_conv4 {
+	renesas,miic-input = <MIIC_SWITCH_PORTB>;
+	status = "okay";
+};
+
+&mii_conv5 {
+	renesas,miic-input = <MIIC_SWITCH_PORTA>;
+	status = "okay";
+};
+
+&pinctrl {
+	pins_can0: pins_can0 {
+		pinmux = <RZN1_PINMUX(162, RZN1_FUNC_CAN)>,	/* CAN0_TXD */
+			 <RZN1_PINMUX(163, RZN1_FUNC_CAN)>;	/* CAN0_RXD */
+		drive-strength = <6>;
+	};
+
+	pins_can1: pins_can1 {
+		pinmux = <RZN1_PINMUX(109, RZN1_FUNC_CAN)>,	/* CAN1_TXD */
+			 <RZN1_PINMUX(110, RZN1_FUNC_CAN)>;	/* CAN1_RXD */
+		drive-strength = <6>;
+	};
+
+	pins_eth3: pins_eth3 {
+		pinmux = <RZN1_PINMUX(36, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(37, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(38, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(39, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(40, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(41, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(42, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(43, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(44, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(45, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(46, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(47, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>;
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	pins_eth4: pins_eth4 {
+		pinmux = <RZN1_PINMUX(48, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(49, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(50, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(51, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(52, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(53, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(54, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(55, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(56, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(57, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(58, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(59, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>;
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	pins_mdio1: pins_mdio1 {
+		pinmux = <RZN1_PINMUX(152, RZN1_FUNC_MDIO1_SWITCH)>,
+			 <RZN1_PINMUX(153, RZN1_FUNC_MDIO1_SWITCH)>;
+	};
+};
+
+&rtc0 {
+	status = "okay";
+};
+
+&switch {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_eth3>, <&pins_eth4>, <&pins_mdio1>;
+
+	dsa,member = <0 0>;
+
+	mdio {
+		clock-frequency = <2500000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0phy4: ethernet-phy@4 {
+			reg = <4>;
+			micrel,led-mode = <1>;
+		};
+
+		switch0phy5: ethernet-phy@5 {
+			reg = <5>;
+			micrel,led-mode = <1>;
+		};
+	};
+};
+
+&switch_port0 {
+	label = "lan0";
+	phy-mode = "mii";
+	phy-handle = <&switch0phy5>;
+	status = "okay";
+};
+
+&switch_port1 {
+	label = "lan1";
+	phy-mode = "mii";
+	phy-handle = <&switch0phy4>;
+	status = "okay";
+};
+
+&switch_port4 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&wdt0 {
+	timeout-sec = <60>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
new file mode 100644
index 000000000000..fa63e1afc4ef
--- /dev/null
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -0,0 +1,477 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Base Device Tree Source for the Renesas RZ/N1D (R9A06G032)
+ *
+ * Copyright (C) 2018 Renesas Electronics Europe Limited
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/r9a06g032-sysctrl.h>
+
+/ {
+	compatible = "renesas,r9a06g032";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0>;
+			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <1>;
+			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+			enable-method = "renesas,r9a06g032-smp";
+			cpu-release-addr = <0 0x4000c204>;
+		};
+	};
+
+	ext_jtag_clk: extjtagclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	ext_mclk: extmclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <40000000>;
+	};
+
+	ext_rgmii_ref: extrgmiiref {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	ext_rtc_clk: extrtcclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&gic>;
+		ranges;
+
+		rtc0: rtc@40006000 {
+			compatible = "renesas,r9a06g032-rtc", "renesas,rzn1-rtc";
+			reg = <0x40006000 0x1000>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 67 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "alarm", "timer", "pps";
+			clocks = <&sysctrl R9A06G032_HCLK_RTC>;
+			clock-names = "hclk";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
+
+		wdt0: watchdog@40008000 {
+			compatible = "renesas,r9a06g032-wdt", "renesas,rzn1-wdt";
+			reg = <0x40008000 0x1000>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sysctrl R9A06G032_CLK_WATCHDOG>;
+			status = "disabled";
+		};
+
+		wdt1: watchdog@40009000 {
+			compatible = "renesas,r9a06g032-wdt", "renesas,rzn1-wdt";
+			reg = <0x40009000 0x1000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sysctrl R9A06G032_CLK_WATCHDOG>;
+			status = "disabled";
+		};
+
+		sysctrl: system-controller@4000c000 {
+			compatible = "renesas,r9a06g032-sysctrl";
+			reg = <0x4000c000 0x1000>;
+			status = "okay";
+			#clock-cells = <1>;
+			#power-domain-cells = <0>;
+
+			clocks = <&ext_mclk>, <&ext_rtc_clk>,
+					<&ext_jtag_clk>, <&ext_rgmii_ref>;
+			clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			dmamux: dma-router@a0 {
+				compatible = "renesas,rzn1-dmamux";
+				reg = <0xa0 4>;
+				#dma-cells = <6>;
+				dma-requests = <32>;
+				dma-masters = <&dma0 &dma1>;
+			};
+		};
+
+		udc: usb@4001e000 {
+			compatible = "renesas,r9a06g032-usbf", "renesas,rzn1-usbf";
+			reg = <0x4001e000 0x2000>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_USBF>,
+				 <&sysctrl R9A06G032_HCLK_USBPM>;
+			clock-names = "hclkf", "hclkpm";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
+
+		pci_usb: pci@40030000 {
+			compatible = "renesas,pci-r9a06g032", "renesas,pci-rzn1";
+			device_type = "pci";
+			clocks = <&sysctrl R9A06G032_HCLK_USBH>,
+				 <&sysctrl R9A06G032_HCLK_USBPM>,
+				 <&sysctrl R9A06G032_CLK_PCI_USB>;
+			clock-names = "hclkh", "hclkpm", "pciclk";
+			power-domains = <&sysctrl>;
+			reg = <0x40030000 0xc00>,
+			      <0x40020000 0x1100>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			bus-range = <0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0x40020000 0x40020000 0 0x00010000>;
+			/* Should map all possible DDR as inbound ranges, but
+			 * the IP only supports a 256MB, 512MB, or 1GB window.
+			 * flags, PCI addr (64-bit), CPU addr, PCI size (64-bit)
+			 */
+			dma-ranges = <0x42000000 0 0x80000000 0x80000000 0 0x40000000>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH
+					 0x0800 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH
+					 0x1000 0 0 2 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+
+			usb@1,0 {
+				reg = <0x800 0 0 0 0>;
+				phys = <&usbphy>;
+				phy-names = "usb";
+			};
+
+			usb@2,0 {
+				reg = <0x1000 0 0 0 0>;
+				phys = <&usbphy>;
+				phy-names = "usb";
+			};
+		};
+
+		uart0: serial@40060000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart", "snps,dw-apb-uart";
+			reg = <0x40060000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART0>, <&sysctrl R9A06G032_HCLK_UART0>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart1: serial@40061000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart", "snps,dw-apb-uart";
+			reg = <0x40061000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART1>, <&sysctrl R9A06G032_HCLK_UART1>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: serial@40062000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart", "snps,dw-apb-uart";
+			reg = <0x40062000 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART2>, <&sysctrl R9A06G032_HCLK_UART2>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart3: serial@50000000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
+			reg = <0x50000000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART3>, <&sysctrl R9A06G032_HCLK_UART3>;
+			clock-names = "baudclk", "apb_pclk";
+			dmas = <&dmamux 0 0 0 0 0 1>, <&dmamux 1 0 0 0 1 1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart4: serial@50001000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
+			reg = <0x50001000 0x400>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART4>, <&sysctrl R9A06G032_HCLK_UART4>;
+			clock-names = "baudclk", "apb_pclk";
+			dmas = <&dmamux 2 0 0 0 2 1>, <&dmamux 3 0 0 0 3 1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart5: serial@50002000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
+			reg = <0x50002000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART5>, <&sysctrl R9A06G032_HCLK_UART5>;
+			clock-names = "baudclk", "apb_pclk";
+			dmas = <&dmamux 4 0 0 0 4 1>, <&dmamux 5 0 0 0 5 1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart6: serial@50003000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
+			reg = <0x50003000 0x400>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART6>, <&sysctrl R9A06G032_HCLK_UART6>;
+			clock-names = "baudclk", "apb_pclk";
+			dmas = <&dmamux 6 0 0 0 6 1>, <&dmamux 7 0 0 0 7 1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart7: serial@50004000 {
+			compatible = "renesas,r9a06g032-uart", "renesas,rzn1-uart";
+			reg = <0x50004000 0x400>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART7>, <&sysctrl R9A06G032_HCLK_UART7>;
+			clock-names = "baudclk", "apb_pclk";
+			dmas = <&dmamux 4 0 0 0 20 1>, <&dmamux 5 0 0 0 21 1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@40067000 {
+			compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl";
+			reg = <0x40067000 0x1000>, <0x51000000 0x480>;
+			clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>;
+			clock-names = "bus";
+			status = "okay";
+		};
+
+		nand_controller: nand-controller@40102000 {
+			compatible = "renesas,r9a06g032-nandc", "renesas,rzn1-nandc";
+			reg = <0x40102000 0x2000>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_NAND>, <&sysctrl R9A06G032_CLK_NAND>;
+			clock-names = "hclk", "eclk";
+			power-domains = <&sysctrl>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		dma0: dma-controller@40104000 {
+			compatible = "renesas,r9a06g032-dma", "renesas,rzn1-dma";
+			reg = <0x40104000 0x1000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "hclk";
+			clocks = <&sysctrl R9A06G032_HCLK_DMA0>;
+			dma-channels = <8>;
+			dma-requests = <16>;
+			dma-masters = <1>;
+			#dma-cells = <3>;
+			block_size = <0xfff>;
+			data-width = <8>;
+		};
+
+		dma1: dma-controller@40105000 {
+			compatible = "renesas,r9a06g032-dma", "renesas,rzn1-dma";
+			reg = <0x40105000 0x1000>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "hclk";
+			clocks = <&sysctrl R9A06G032_HCLK_DMA1>;
+			dma-channels = <8>;
+			dma-requests = <16>;
+			dma-masters = <1>;
+			#dma-cells = <3>;
+			block_size = <0xfff>;
+			data-width = <8>;
+		};
+
+		gmac2: ethernet@44002000 {
+			compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
+			reg = <0x44002000 0x2000>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			clocks = <&sysctrl R9A06G032_HCLK_GMAC1>;
+			clock-names = "stmmaceth";
+			power-domains = <&sysctrl>;
+			snps,multicast-filter-bins = <256>;
+			snps,perfect-filter-entries = <128>;
+			tx-fifo-depth = <2048>;
+			rx-fifo-depth = <4096>;
+			status = "disabled";
+		};
+
+		eth_miic: eth-miic@44030000 {
+			compatible = "renesas,r9a06g032-miic", "renesas,rzn1-miic";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x44030000 0x10000>;
+			clocks = <&sysctrl R9A06G032_CLK_MII_REF>,
+				 <&sysctrl R9A06G032_CLK_RGMII_REF>,
+				 <&sysctrl R9A06G032_CLK_RMII_REF>,
+				 <&sysctrl R9A06G032_HCLK_SWITCH_RG>;
+			clock-names = "mii_ref", "rgmii_ref", "rmii_ref", "hclk";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+
+			mii_conv1: mii-conv@1 {
+				reg = <1>;
+				status = "disabled";
+			};
+
+			mii_conv2: mii-conv@2 {
+				reg = <2>;
+				status = "disabled";
+			};
+
+			mii_conv3: mii-conv@3 {
+				reg = <3>;
+				status = "disabled";
+			};
+
+			mii_conv4: mii-conv@4 {
+				reg = <4>;
+				status = "disabled";
+			};
+
+			mii_conv5: mii-conv@5 {
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		switch: switch@44050000 {
+			compatible = "renesas,r9a06g032-a5psw", "renesas,rzn1-a5psw";
+			reg = <0x44050000 0x10000>;
+			clocks = <&sysctrl R9A06G032_HCLK_SWITCH>,
+				 <&sysctrl R9A06G032_CLK_SWITCH>;
+			clock-names = "hclk", "clk";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch_port0: port@0 {
+					reg = <0>;
+					pcs-handle = <&mii_conv5>;
+					status = "disabled";
+				};
+
+				switch_port1: port@1 {
+					reg = <1>;
+					pcs-handle = <&mii_conv4>;
+					status = "disabled";
+				};
+
+				switch_port2: port@2 {
+					reg = <2>;
+					pcs-handle = <&mii_conv3>;
+					status = "disabled";
+				};
+
+				switch_port3: port@3 {
+					reg = <3>;
+					pcs-handle = <&mii_conv2>;
+					status = "disabled";
+				};
+
+				switch_port4: port@4 {
+					reg = <4>;
+					ethernet = <&gmac2>;
+					label = "cpu";
+					phy-mode = "internal";
+					status = "disabled";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+
+		gic: interrupt-controller@44101000 {
+			compatible = "arm,gic-400", "arm,cortex-a7-gic";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x44101000 0x1000>, /* Distributer */
+			      <0x44102000 0x2000>, /* CPU interface */
+			      <0x44104000 0x2000>, /* Virt interface control */
+			      <0x44106000 0x2000>; /* Virt CPU interface */
+			interrupts =
+				<GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		can0: can@52104000 {
+			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
+			reg = <0x52104000 0x800>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_CAN0>;
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
+
+		can1: can@52105000 {
+			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
+			reg = <0x52105000 0x800>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_CAN1>;
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		arm,cpu-registers-not-fw-configured;
+		always-on;
+		interrupts =
+			<GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	usbphy: usb-phy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		status = "disabled";
+	};
+};
diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/renesas/sh73a0-kzm9g.dts
index 1916f31a30ff..98897f710063 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/renesas/sh73a0-kzm9g.dts
@@ -25,12 +25,9 @@
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&vdd_dvfs>;
-			operating-points = <
-				/* kHz  uV */
-				1196000 1315000
-				 598000 1175000
-				 398667 1065000
-			>;
+			operating-points = <1196000 1315000>,	/* kHz  uV */
+					   < 598000 1175000>,
+					   < 398667 1065000>;
 			voltage-tolerance = <1>; /* 1% */
 		};
 	};
@@ -172,7 +169,7 @@
 
 &bsc {
 	ethernet@10000000 {
-		compatible = "smsc,lan9220", "smsc,lan9115";
+		compatible = "smsc,lan9221", "smsc,lan9115";
 		reg = <0x10000000 0x100>;
 		phy-mode = "mii";
 		interrupt-parent = <&irqpin0>;
diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/renesas/sh73a0.dtsi
index 33836990b102..30c67acc4e35 100644
--- a/arch/arm/boot/dts/sh73a0.dtsi
+++ b/arch/arm/boot/dts/renesas/sh73a0.dtsi
@@ -39,11 +39,18 @@
 		};
 	};
 
+	timer@f0000200 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0xf0000200 0x100>;
+		interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
+		clocks = <&periph_clk>;
+	};
+
 	timer@f0000600 {
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0xf0000600 0x20>;
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
-		clocks = <&twd_clk>;
+		clocks = <&periph_clk>;
 	};
 
 	gic: interrupt-controller@f0001000 {
@@ -92,7 +99,7 @@
 	};
 
 	cmt1: timer@e6138000 {
-		compatible = "renesas,cmt-48-sh73a0", "renesas,cmt-48";
+		compatible = "renesas,sh73a0-cmt1";
 		reg = <0xe6138000 0x200>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks SH73A0_CLK_CMT1>;
@@ -110,14 +117,14 @@
 			<0xe6900020 1>,
 			<0xe6900040 1>,
 			<0xe6900060 1>;
-		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
 		power-domains = <&pd_a4s>;
 		control-parent;
@@ -132,14 +139,14 @@
 			<0xe6900024 1>,
 			<0xe6900044 1>,
 			<0xe6900064 1>;
-		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
 		power-domains = <&pd_a4s>;
 		control-parent;
@@ -154,14 +161,14 @@
 			<0xe6900028 1>,
 			<0xe6900048 1>,
 			<0xe6900068 1>;
-		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
 		power-domains = <&pd_a4s>;
 		control-parent;
@@ -176,14 +183,14 @@
 			<0xe690002c 1>,
 			<0xe690004c 1>,
 			<0xe690006c 1>;
-		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
 		power-domains = <&pd_a4s>;
 		control-parent;
@@ -194,10 +201,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-sh73a0", "renesas,rmobile-iic";
 		reg = <0xe6820000 0x425>;
-		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp1_clks SH73A0_CLK_IIC0>;
 		power-domains = <&pd_a3sp>;
 		status = "disabled";
@@ -208,10 +215,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-sh73a0", "renesas,rmobile-iic";
 		reg = <0xe6822000 0x425>;
-		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks SH73A0_CLK_IIC1>;
 		power-domains = <&pd_a3sp>;
 		status = "disabled";
@@ -222,10 +229,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-sh73a0", "renesas,rmobile-iic";
 		reg = <0xe6824000 0x425>;
-		interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks SH73A0_CLK_IIC2>;
 		power-domains = <&pd_a3sp>;
 		status = "disabled";
@@ -236,10 +243,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-sh73a0", "renesas,rmobile-iic";
 		reg = <0xe6826000 0x425>;
-		interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp4_clks SH73A0_CLK_IIC3>;
 		power-domains = <&pd_a3sp>;
 		status = "disabled";
@@ -250,10 +257,10 @@
 		#size-cells = <0>;
 		compatible = "renesas,iic-sh73a0", "renesas,rmobile-iic";
 		reg = <0xe6828000 0x425>;
-		interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp4_clks SH73A0_CLK_IIC4>;
 		power-domains = <&pd_c5>;
 		status = "disabled";
@@ -262,8 +269,8 @@
 	mmcif: mmc@e6bd0000 {
 		compatible = "renesas,mmcif-sh73a0", "renesas,sh-mmcif";
 		reg = <0xe6bd0000 0x100>;
-		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks SH73A0_CLK_MMCIF0>;
 		power-domains = <&pd_a3sp>;
 		reg-io-width = <4>;
@@ -314,12 +321,12 @@
 		status = "disabled";
 	};
 
-	sdhi0: sd@ee100000 {
+	sdhi0: mmc@ee100000 {
 		compatible = "renesas,sdhi-sh73a0";
 		reg = <0xee100000 0x100>;
-		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks SH73A0_CLK_SDHI0>;
 		power-domains = <&pd_a3sp>;
 		cap-sd-highspeed;
@@ -327,11 +334,11 @@
 	};
 
 	/* SDHI1 and SDHI2 have no CD pins, no need for CD IRQ */
-	sdhi1: sd@ee120000 {
+	sdhi1: mmc@ee120000 {
 		compatible = "renesas,sdhi-sh73a0";
 		reg = <0xee120000 0x100>;
-		interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks SH73A0_CLK_SDHI1>;
 		power-domains = <&pd_a3sp>;
 		disable-wp;
@@ -339,11 +346,11 @@
 		status = "disabled";
 	};
 
-	sdhi2: sd@ee140000 {
+	sdhi2: mmc@ee140000 {
 		compatible = "renesas,sdhi-sh73a0";
 		reg = <0xee140000 0x100>;
-		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks SH73A0_CLK_SDHI2>;
 		power-domains = <&pd_a3sp>;
 		disable-wp;
@@ -441,7 +448,7 @@
 		status = "disabled";
 	};
 
-	pfc: pin-controller@e6050000 {
+	pfc: pinctrl@e6050000 {
 		compatible = "renesas,pfc-sh73a0";
 		reg = <0xe6050000 0x8000>,
 		      <0xe605801c 0x1c>;
@@ -577,6 +584,7 @@
 		compatible = "renesas,fsi2-sh73a0", "renesas,sh_fsi2";
 		reg = <0xec230000 0x400>;
 		interrupts = <GIC_SPI 146 0x4>;
+		clocks = <&mstp3_clks SH73A0_CLK_FSI>;
 		power-domains = <&pd_a4mp>;
 		status = "disabled";
 	};
@@ -612,19 +620,25 @@
 		extal2_clk: extal2 {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			/* This value must be overridden by the board. */
+			clock-frequency = <0>;
 		};
 		extcki_clk: extcki {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			/* This value can be overridden by the board. */
+			clock-frequency = <0>;
 		};
 		fsiack_clk: fsiack {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			/* This value can be overridden by the board. */
 			clock-frequency = <0>;
 		};
 		fsibck_clk: fsibck {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			/* This value can be overridden by the board. */
 			clock-frequency = <0>;
 		};
 
@@ -812,7 +826,7 @@
 			clock-div = <13>;
 			clock-mult = <1>;
 		};
-		twd_clk: twd {
+		periph_clk: periph {
 			compatible = "fixed-factor-clock";
 			clocks = <&cpg_clocks SH73A0_CLK_Z>;
 			#clock-cells = <0>;
diff --git a/arch/arm/boot/dts/rockchip/Makefile b/arch/arm/boot/dts/rockchip/Makefile
new file mode 100644
index 000000000000..ab4cd9aab722
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/Makefile
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ROCKCHIP) += \
+	rv1108-elgin-r1.dtb \
+	rv1108-evb.dtb \
+	rv1109-sonoff-ihost.dtb \
+	rv1126-edgeble-neu2-io.dtb \
+	rv1126-sonoff-ihost.dtb \
+	rk3036-evb.dtb \
+	rk3036-kylin.dtb \
+	rk3066a-bqcurie2.dtb \
+	rk3066a-marsboard.dtb \
+	rk3066a-mk808.dtb \
+	rk3066a-rayeager.dtb \
+	rk3128-evb.dtb \
+	rk3128-xpi-3128.dtb \
+	rk3188-bqedison2qc.dtb \
+	rk3188-px3-evb.dtb \
+	rk3188-radxarock.dtb \
+	rk3228-evb.dtb \
+	rk3229-evb.dtb \
+	rk3229-xms6.dtb \
+	rk3288-evb-act8846.dtb \
+	rk3288-evb-rk808.dtb \
+	rk3288-firefly-beta.dtb \
+	rk3288-firefly.dtb \
+	rk3288-firefly-reload.dtb \
+	rk3288-miqi.dtb \
+	rk3288-phycore-rdk.dtb \
+	rk3288-popmetal.dtb \
+	rk3288-r89.dtb \
+	rk3288-rock2-square.dtb \
+	rk3288-rock-pi-n8.dtb \
+	rk3288-tinker.dtb \
+	rk3288-tinker-s.dtb \
+	rk3288-veyron-brain.dtb \
+	rk3288-veyron-fievel.dtb \
+	rk3288-veyron-jaq.dtb \
+	rk3288-veyron-jerry.dtb \
+	rk3288-veyron-mickey.dtb \
+	rk3288-veyron-mighty.dtb \
+	rk3288-veyron-minnie.dtb \
+	rk3288-veyron-pinky.dtb \
+	rk3288-veyron-speedy.dtb \
+	rk3288-veyron-tiger.dtb \
+	rk3288-vyasa.dtb
diff --git a/arch/arm/boot/dts/rk3036-evb.dts b/arch/arm/boot/dts/rockchip/rk3036-evb.dts
index 2a7e6624efb9..becdc0b664bf 100644
--- a/arch/arm/boot/dts/rk3036-evb.dts
+++ b/arch/arm/boot/dts/rockchip/rk3036-evb.dts
@@ -15,27 +15,30 @@
 };
 
 &emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	phy = <&phy0>;
-	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
 	phy-reset-duration = <10>; /* millisecond */
-
+	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
 	};
 };
 
 &i2c1 {
 	status = "okay";
 
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 	};
 };
diff --git a/arch/arm/boot/dts/rk3036-kylin.dts b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
index fb3cf005cc90..e32c73d32f0a 100644
--- a/arch/arm/boot/dts/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
@@ -8,15 +8,30 @@
 	model = "Rockchip RK3036 KylinBoard";
 	compatible = "rockchip,rk3036-kylin", "rockchip,rk3036";
 
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x20000000>;
 	};
 
+	hdmi_con: hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds: gpio-leds {
 		compatible = "gpio-leds";
 
-		work {
+		work_led: led-0 {
 			gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
 			label = "kylin:red:led";
 			pinctrl-names = "default";
@@ -80,16 +95,20 @@
 };
 
 &emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	phy = <&phy0>;
-	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
 	phy-reset-duration = <10>; /* millisecond */
-
+	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
 	};
 };
 
@@ -106,6 +125,12 @@
 	status = "okay";
 };
 
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 
@@ -319,7 +344,7 @@
 	bus-width = <4>;
 	cap-sd-highspeed;
 	cap-sdio-irq;
-	default-sample-phase = <90>;
+	rockchip,default-sample-phase = <90>;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&sdio_pwrseq>;
 	non-removable;
@@ -390,7 +415,7 @@
 		};
 	};
 
-	sleep {
+	suspend {
 		global_pwroff: global-pwroff {
 			rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
 		};
diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rockchip/rk3036.dtsi
index c70182c5aeb1..04af224005f8 100644
--- a/arch/arm/boot/dts/rk3036.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3036.dtsi
@@ -6,6 +6,7 @@
 #include <dt-bindings/pinctrl/rockchip.h>
 #include <dt-bindings/clock/rk3036-cru.h>
 #include <dt-bindings/soc/rockchip,boot-mode.h>
+#include <dt-bindings/power/rk3036-power.h>
 
 / {
 	#address-cells = <1>;
@@ -16,6 +17,9 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c2 = &i2c2;
@@ -54,24 +58,6 @@
 		};
 	};
 
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		pdma: pdma@20078000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x20078000 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMAC2>;
-			clock-names = "apb_pclk";
-		};
-	};
-
 	arm-pmu {
 		compatible = "arm,cortex-a7-pmu";
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
@@ -101,7 +87,7 @@
 		#clock-cells = <0>;
 	};
 
-	bus_intmem@10080000 {
+	bus_intmem: sram@10080000 {
 		compatible = "mmio-sram";
 		reg = <0x10080000 0x2000>;
 		#address-cells = <1>;
@@ -128,11 +114,33 @@
 		assigned-clocks = <&cru SCLK_GPU>;
 		assigned-clock-rates = <100000000>;
 		clocks = <&cru SCLK_GPU>, <&cru SCLK_GPU>;
-		clock-names = "core", "bus";
+		clock-names = "bus", "core";
+		power-domains = <&power RK3036_PD_GPU>;
 		resets = <&cru SRST_GPU>;
 		status = "disabled";
 	};
 
+	vpu: video-codec@10108000 {
+		compatible = "rockchip,rk3036-vpu";
+		reg = <0x10108000 0x800>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "vdpu";
+		clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>;
+		clock-names = "aclk", "hclk";
+		iommus = <&vpu_mmu>;
+		power-domains = <&power RK3036_PD_VPU>;
+	};
+
+	vpu_mmu: iommu@10108800 {
+		compatible = "rockchip,iommu";
+		reg = <0x10108800 0x100>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>;
+		clock-names = "aclk", "iface";
+		power-domains = <&power RK3036_PD_VPU>;
+		#iommu-cells = <0>;
+	};
+
 	vop: vop@10118000 {
 		compatible = "rockchip,rk3036-vop";
 		reg = <0x10118000 0x19c>;
@@ -142,6 +150,7 @@
 		resets = <&cru SRST_LCDC1_A>, <&cru SRST_LCDC1_H>, <&cru SRST_LCDC1_D>;
 		reset-names = "axi", "ahb", "dclk";
 		iommus = <&vop_mmu>;
+		power-domains = <&power RK3036_PD_VIO>;
 		status = "disabled";
 
 		vop_out: port {
@@ -158,13 +167,28 @@
 		compatible = "rockchip,iommu";
 		reg = <0x10118300 0x100>;
 		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_LCDC>, <&cru HCLK_LCDC>;
 		clock-names = "aclk", "iface";
+		power-domains = <&power RK3036_PD_VIO>;
 		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
+	qos_gpu: qos@1012d000 {
+		compatible = "rockchip,rk3036-qos", "syscon";
+		reg = <0x1012d000 0x20>;
+	};
+
+	qos_vpu: qos@1012e000 {
+		compatible = "rockchip,rk3036-qos", "syscon";
+		reg = <0x1012e000 0x20>;
+	};
+
+	qos_vio: qos@1012f000 {
+		compatible = "rockchip,rk3036-qos", "syscon";
+		reg = <0x1012f000 0x20>;
+	};
+
 	gic: interrupt-controller@10139000 {
 		compatible = "arm,gic-400";
 		interrupt-controller;
@@ -204,11 +228,9 @@
 	};
 
 	emac: ethernet@10200000 {
-		compatible = "rockchip,rk3036-emac", "snps,arc-emac";
+		compatible = "rockchip,rk3036-emac";
 		reg = <0x10200000 0x4000>;
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		rockchip,grf = <&grf>;
 		clocks = <&cru HCLK_MAC>, <&cru SCLK_MACREF>, <&cru SCLK_MAC>;
 		clock-names = "hclk", "macref", "macclk";
@@ -224,7 +246,7 @@
 		status = "disabled";
 	};
 
-	sdmmc: dwmmc@10214000 {
+	sdmmc: mmc@10214000 {
 		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x10214000 0x4000>;
 		clock-frequency = <37500000>;
@@ -238,7 +260,7 @@
 		status = "disabled";
 	};
 
-	sdio: dwmmc@10218000 {
+	sdio: mmc@10218000 {
 		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x10218000 0x4000>;
 		max-frequency = <37500000>;
@@ -252,7 +274,7 @@
 		status = "disabled";
 	};
 
-	emmc: dwmmc@1021c000 {
+	emmc: mmc@1021c000 {
 		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x1021c000 0x4000>;
 		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
@@ -263,7 +285,6 @@
 		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
 			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
 		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
-		default-sample-phase = <158>;
 		disable-wp;
 		dmas = <&pdma 12>;
 		dma-names = "rx-tx";
@@ -281,8 +302,6 @@
 		compatible = "rockchip,rk3036-i2s", "rockchip,rk3066-i2s";
 		reg = <0x10220000 0x4000>;
 		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		clock-names = "i2s_clk", "i2s_hclk";
 		clocks = <&cru SCLK_I2S>, <&cru HCLK_I2S>;
 		dmas = <&pdma 0>, <&pdma 1>;
@@ -293,9 +312,26 @@
 		status = "disabled";
 	};
 
+	nfc: nand-controller@10500000 {
+		compatible = "rockchip,rk3036-nfc",
+			     "rockchip,rk2928-nfc";
+		reg = <0x10500000 0x4000>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+		clock-names = "ahb", "nfc";
+		assigned-clocks = <&cru SCLK_NANDC>;
+		assigned-clock-rates = <150000000>;
+		pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_csn0
+			     &flash_rdn &flash_rdy &flash_wrn>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	cru: clock-controller@20000000 {
 		compatible = "rockchip,rk3036-cru";
 		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -307,6 +343,37 @@
 		compatible = "rockchip,rk3036-grf", "syscon", "simple-mfd";
 		reg = <0x20008000 0x1000>;
 
+		power: power-controller {
+			compatible = "rockchip,rk3036-power-controller";
+			#power-domain-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-domain@RK3036_PD_VIO {
+				reg = <RK3036_PD_VIO>;
+				clocks = <&cru ACLK_LCDC>,
+					 <&cru HCLK_LCDC>,
+					 <&cru SCLK_LCDC>;
+				pm_qos = <&qos_vio>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3036_PD_VPU {
+				reg = <RK3036_PD_VPU>;
+				clocks = <&cru ACLK_VCODEC>,
+					 <&cru HCLK_VCODEC>;
+				pm_qos = <&qos_vpu>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3036_PD_GPU {
+				reg = <RK3036_PD_GPU>;
+				clocks = <&cru SCLK_GPU>;
+				pm_qos = <&qos_gpu>;
+				#power-domain-cells = <0>;
+			};
+		};
+
 		reboot-mode {
 			compatible = "syscon-reboot-mode";
 			offset = <0x1d8>;
@@ -337,12 +404,20 @@
 		pinctrl-0 = <&hdmi_ctl>;
 		status = "disabled";
 
-		hdmi_in: port {
+		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			hdmi_in_vop: endpoint@0 {
+
+			hdmi_in: port@0 {
 				reg = <0>;
-				remote-endpoint = <&vop_out_hdmi>;
+
+				hdmi_in_vop: endpoint {
+					remote-endpoint = <&vop_out_hdmi>;
+				};
+			};
+
+			hdmi_out: port@1 {
+				reg = <1>;
 			};
 		};
 	};
@@ -351,8 +426,8 @@
 		compatible = "rockchip,rk3036-timer", "rockchip,rk3288-timer";
 		reg = <0x20044000 0x20>;
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};
 
 	pwm0: pwm@20050000 {
@@ -360,7 +435,6 @@
 		reg = <0x20050000 0x10>;
 		#pwm-cells = <3>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm0_pin>;
 		status = "disabled";
@@ -371,7 +445,6 @@
 		reg = <0x20050010 0x10>;
 		#pwm-cells = <3>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm1_pin>;
 		status = "disabled";
@@ -382,7 +455,6 @@
 		reg = <0x20050020 0x10>;
 		#pwm-cells = <3>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm2_pin>;
 		status = "disabled";
@@ -393,7 +465,6 @@
 		reg = <0x20050030 0x10>;
 		#pwm-cells = <2>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm3_pin>;
 		status = "disabled";
@@ -495,6 +566,18 @@
 		status = "disabled";
 	};
 
+	pdma: dma-controller@20078000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x20078000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC2>;
+		clock-names = "apb_pclk";
+	};
+
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3036-pinctrl";
 		rockchip,grf = <&grf>;
@@ -502,7 +585,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@2007c000 {
+		gpio0: gpio@2007c000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2007c000 0x100>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
@@ -515,7 +598,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@20080000 {
+		gpio1: gpio@20080000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20080000 0x100>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
@@ -528,7 +611,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@20084000 {
+		gpio2: gpio@20084000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20084000 0x100>;
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
@@ -541,7 +624,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		pcfg_pull_default: pcfg_pull_default {
+		pcfg_pull_default: pcfg-pull-default {
 			bias-pull-pin-default;
 		};
 
@@ -644,6 +727,43 @@
 			};
 		};
 
+		nfc {
+			flash_ale: flash-ale {
+				rockchip,pins = <2 RK_PA0 1 &pcfg_pull_default>;
+			};
+
+			flash_bus8: flash-bus8 {
+				rockchip,pins = <1 RK_PD0 1 &pcfg_pull_default>,
+						<1 RK_PD1 1 &pcfg_pull_default>,
+						<1 RK_PD2 1 &pcfg_pull_default>,
+						<1 RK_PD3 1 &pcfg_pull_default>,
+						<1 RK_PD4 1 &pcfg_pull_default>,
+						<1 RK_PD5 1 &pcfg_pull_default>,
+						<1 RK_PD6 1 &pcfg_pull_default>,
+						<1 RK_PD7 1 &pcfg_pull_default>;
+			};
+
+			flash_cle: flash-cle {
+				rockchip,pins = <2 RK_PA1 1 &pcfg_pull_default>;
+			};
+
+			flash_csn0: flash-csn0 {
+				rockchip,pins = <2 RK_PA6 1 &pcfg_pull_default>;
+			};
+
+			flash_rdn: flash-rdn {
+				rockchip,pins = <2 RK_PA3 1 &pcfg_pull_default>;
+			};
+
+			flash_rdy: flash-rdy {
+				rockchip,pins = <2 RK_PA4 1 &pcfg_pull_default>;
+			};
+
+			flash_wrn: flash-wrn {
+				rockchip,pins = <2 RK_PA2 1 &pcfg_pull_default>;
+			};
+		};
+
 		emac {
 			emac_xfer: emac-xfer {
 				rockchip,pins = <2 RK_PB2 1 &pcfg_pull_default>, /* crs_dvalid */
diff --git a/arch/arm/boot/dts/rk3066a-bqcurie2.dts b/arch/arm/boot/dts/rockchip/rk3066a-bqcurie2.dts
index 0a56a2f1bc4d..f924d4d64c3d 100644
--- a/arch/arm/boot/dts/rk3066a-bqcurie2.dts
+++ b/arch/arm/boot/dts/rockchip/rk3066a-bqcurie2.dts
@@ -12,6 +12,11 @@
 	model = "bq Curie 2";
 	compatible = "mundoreader,bq-curie2", "rockchip,rk3066a";
 
+	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -43,7 +48,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			gpios = <&gpio6 RK_PA2 GPIO_ACTIVE_LOW>; /* GPIO6_A2 */
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -51,7 +56,7 @@
 			wakeup-source;
 			debounce-interval = <100>;
 		};
-		volume-down {
+		key-volume-down {
 			gpios = <&gpio4 RK_PC5 GPIO_ACTIVE_LOW>; /* GPIO4_C5 */
 			linux,code = <KEY_VOLUMEDOWN>;
 			label = "GPIO Key Vol-";
@@ -63,7 +68,11 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_arm>;
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
 };
 
 &i2c1 {
@@ -150,7 +159,7 @@
 };
 
 /* must be included after &tps gets defined */
-#include "tps65910.dtsi"
+#include "../tps65910.dtsi"
 
 &mmc0 { /* sdmmc */
 	status = "okay";
diff --git a/arch/arm/boot/dts/rk3066a-marsboard.dts b/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
index 7e01f6406a86..f6e8d49a02ef 100644
--- a/arch/arm/boot/dts/rk3066a-marsboard.dts
+++ b/arch/arm/boot/dts/rockchip/rk3066a-marsboard.dts
@@ -10,6 +10,10 @@
 	model = "MarsBoard RK3066";
 	compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a";
 
+	aliases {
+		mmc0 = &mmc0;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -47,7 +51,11 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_arm>;
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
 };
 
 &i2c1 {
@@ -139,21 +147,24 @@
 };
 
 /* must be included after &tps gets defined */
-#include "tps65910.dtsi"
+#include "../tps65910.dtsi"
 
 &emac {
-	status = "okay";
-
 	phy = <&phy0>;
 	phy-supply = <&vcc_rmii>;
-
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3066a-mk808.dts b/arch/arm/boot/dts/rockchip/rk3066a-mk808.dts
index 365eff621113..06790f05b395 100644
--- a/arch/arm/boot/dts/rk3066a-mk808.dts
+++ b/arch/arm/boot/dts/rockchip/rk3066a-mk808.dts
@@ -4,12 +4,18 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/input/input.h>
 #include "rk3066a.dtsi"
 
 / {
 	model = "Rikomagic MK808";
 	compatible = "rikomagic,mk808", "rockchip,rk3066a";
 
+	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
@@ -19,10 +25,24 @@
 		device_type = "memory";
 	};
 
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <2500000>;
+		poll-interval = <100>;
+
+		button-recovery {
+			label = "recovery";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <0>;
+		};
+	};
+
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		blue {
+		blue_led: led-0 {
 			label = "mk808:blue:power";
 			gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -41,6 +61,13 @@
 		};
 	};
 
+	vcc_2v5: vcc-2v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_2v5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+	};
+
 	vcc_io: vcc-io {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_io";
@@ -130,7 +157,32 @@
 	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4>;
 	pinctrl-names = "default";
 	vmmc-supply = <&vcc_wifi>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&nfc {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "rk-nand";
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-step-size = <1024>;
+		nand-ecc-strength = <40>;
+		nand-is-boot-medium;
+		rockchip,boot-blks = <8>;
+		rockchip,boot-ecc-strength = <24>;
+	};
 };
 
 &pinctrl {
@@ -159,6 +211,11 @@
 	};
 };
 
+&saradc {
+	vref-supply = <&vcc_2v5>;
+	status = "okay";
+};
+
 &uart2 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
index f9db6bb9fa11..29d8e5bf88f5 100644
--- a/arch/arm/boot/dts/rk3066a-rayeager.dts
+++ b/arch/arm/boot/dts/rockchip/rk3066a-rayeager.dts
@@ -11,6 +11,12 @@
 	model = "Rayeager PX2";
 	compatible = "chipspark,rayeager-px2", "rockchip,rk3066a";
 
+	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		mmc2 = &emmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -26,7 +32,7 @@
 	keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio6 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
@@ -58,7 +64,7 @@
 	};
 
 	/* input for 5V_STDBY is VSYS or DC5V, selectable by jumper J4 */
-	vcc_stdby: 5v-stdby-regulator {
+	vcc_stdby: stdby-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "5v_stdby";
 		regulator-min-microvolt = <5000000>;
@@ -128,19 +134,28 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_arm>;
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
 };
 
 &emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>;
 	phy = <&phy0>;
 	phy-supply = <&vcc_rmii>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>;
 	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };
 
@@ -281,7 +296,7 @@
 	};
 };
 
-#include "tps65910.dtsi"
+#include "../tps65910.dtsi"
 
 &i2c2 {
 	status = "okay";
diff --git a/arch/arm/boot/dts/rk3066a.dtsi b/arch/arm/boot/dts/rockchip/rk3066a.dtsi
index 3d1b02f45ffd..30139f21de64 100644
--- a/arch/arm/boot/dts/rk3066a.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3066a.dtsi
@@ -13,6 +13,11 @@
 / {
 	compatible = "rockchip,rk3066a";
 
+	aliases {
+		gpio4 = &gpio4;
+		gpio6 = &gpio6;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -23,20 +28,19 @@
 			compatible = "arm,cortex-a9";
 			next-level-cache = <&L2>;
 			reg = <0x0>;
-			operating-points = <
+			operating-points =
 				/* kHz    uV */
-				1416000 1300000
-				1200000 1175000
-				1008000 1125000
-				816000  1125000
-				600000  1100000
-				504000  1100000
-				312000  1075000
-			>;
+				<1416000 1300000>,
+				<1200000 1175000>,
+				<1008000 1125000>,
+				<816000  1125000>,
+				<600000  1100000>,
+				<504000  1100000>,
+				<312000  1075000>;
 			clock-latency = <40000>;
 			clocks = <&cru ARMCLK>;
 		};
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			next-level-cache = <&L2>;
@@ -156,14 +160,12 @@
 		compatible = "rockchip,rk3066-i2s";
 		reg = <0x10118000 0x2000>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s0_bus>;
+		clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0>;
+		clock-names = "i2s_clk", "i2s_hclk";
 		dmas = <&dmac1_s 4>, <&dmac1_s 5>;
 		dma-names = "tx", "rx";
-		clock-names = "i2s_hclk", "i2s_clk";
-		clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
 		rockchip,playback-channels = <8>;
 		rockchip,capture-channels = <2>;
 		#sound-dai-cells = <0>;
@@ -174,14 +176,12 @@
 		compatible = "rockchip,rk3066-i2s";
 		reg = <0x1011a000 0x2000>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s1_bus>;
+		clocks = <&cru SCLK_I2S1>, <&cru HCLK_I2S1>;
+		clock-names = "i2s_clk", "i2s_hclk";
 		dmas = <&dmac1_s 6>, <&dmac1_s 7>;
 		dma-names = "tx", "rx";
-		clock-names = "i2s_hclk", "i2s_clk";
-		clocks = <&cru HCLK_I2S1>, <&cru SCLK_I2S1>;
 		rockchip,playback-channels = <2>;
 		rockchip,capture-channels = <2>;
 		#sound-dai-cells = <0>;
@@ -192,14 +192,12 @@
 		compatible = "rockchip,rk3066-i2s";
 		reg = <0x1011c000 0x2000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s2_bus>;
+		clocks = <&cru SCLK_I2S2>, <&cru HCLK_I2S2>;
+		clock-names = "i2s_clk", "i2s_hclk";
 		dmas = <&dmac1_s 9>, <&dmac1_s 10>;
 		dma-names = "tx", "rx";
-		clock-names = "i2s_hclk", "i2s_clk";
-		clocks = <&cru HCLK_I2S2>, <&cru SCLK_I2S2>;
 		rockchip,playback-channels = <2>;
 		rockchip,capture-channels = <2>;
 		#sound-dai-cells = <0>;
@@ -209,8 +207,9 @@
 	cru: clock-controller@20000000 {
 		compatible = "rockchip,rk3066a-cru";
 		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
-
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		assigned-clocks = <&cru PLL_CPLL>, <&cru PLL_GPLL>,
@@ -223,8 +222,8 @@
 				       <150000000>, <75000000>;
 	};
 
-	timer@2000e000 {
-		compatible = "snps,dw-apb-timer-osc";
+	timer2: timer@2000e000 {
+		compatible = "snps,dw-apb-timer";
 		reg = <0x2000e000 0x100>;
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_TIMER2>, <&cru PCLK_TIMER2>;
@@ -244,16 +243,16 @@
 		};
 	};
 
-	timer@20038000 {
-		compatible = "snps,dw-apb-timer-osc";
+	timer0: timer@20038000 {
+		compatible = "snps,dw-apb-timer";
 		reg = <0x20038000 0x100>;
 		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_TIMER0>, <&cru PCLK_TIMER0>;
 		clock-names = "timer", "pclk";
 	};
 
-	timer@2003a000 {
-		compatible = "snps,dw-apb-timer-osc";
+	timer1: timer@2003a000 {
+		compatible = "snps,dw-apb-timer";
 		reg = <0x2003a000 0x100>;
 		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_TIMER1>, <&cru PCLK_TIMER1>;
@@ -272,30 +271,6 @@
 		status = "disabled";
 	};
 
-	usbphy: phy {
-		compatible = "rockchip,rk3066a-usb-phy", "rockchip,rk3288-usb-phy";
-		rockchip,grf = <&grf>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-
-		usbphy0: usb-phy@17c {
-			#phy-cells = <0>;
-			reg = <0x17c>;
-			clocks = <&cru SCLK_OTGPHY0>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-
-		usbphy1: usb-phy@188 {
-			#phy-cells = <0>;
-			reg = <0x188>;
-			clocks = <&cru SCLK_OTGPHY1>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-	};
-
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3066a-pinctrl";
 		rockchip,grf = <&grf>;
@@ -303,7 +278,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@20034000 {
+		gpio0: gpio@20034000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20034000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -316,7 +291,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@2003c000 {
+		gpio1: gpio@2003c000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2003c000 0x100>;
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -329,7 +304,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@2003e000 {
+		gpio2: gpio@2003e000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2003e000 0x100>;
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
@@ -342,7 +317,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@20080000 {
+		gpio3: gpio@20080000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20080000 0x100>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
@@ -355,7 +330,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio4: gpio4@20084000 {
+		gpio4: gpio@20084000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20084000 0x100>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
@@ -368,7 +343,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio6: gpio6@2000a000 {
+		gpio6: gpio@2000a000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2000a000 0x100>;
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -381,11 +356,11 @@
 			#interrupt-cells = <2>;
 		};
 
-		pcfg_pull_default: pcfg_pull_default {
+		pcfg_pull_default: pcfg-pull-default {
 			bias-pull-pin-default;
 		};
 
-		pcfg_pull_none: pcfg_pull_none {
+		pcfg_pull_none: pcfg-pull-none {
 			bias-disable;
 		};
 
@@ -708,6 +683,33 @@
 	power-domains = <&power RK3066_PD_GPU>;
 };
 
+&grf {
+	compatible = "rockchip,rk3066-grf", "syscon", "simple-mfd";
+
+	usbphy: usbphy {
+		compatible = "rockchip,rk3066a-usb-phy";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		usbphy0: usb-phy@17c {
+			reg = <0x17c>;
+			clocks = <&cru SCLK_OTGPHY0>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+		};
+
+		usbphy1: usb-phy@188 {
+			reg = <0x188>;
+			clocks = <&cru SCLK_OTGPHY1>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+		};
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_xfer>;
@@ -761,7 +763,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pd_vio@RK3066_PD_VIO {
+		power-domain@RK3066_PD_VIO {
 			reg = <RK3066_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -786,21 +788,24 @@
 				 <&qos_cif1>,
 				 <&qos_ipp>,
 				 <&qos_rga>;
+			#power-domain-cells = <0>;
 		};
 
-		pd_video@RK3066_PD_VIDEO {
+		power-domain@RK3066_PD_VIDEO {
 			reg = <RK3066_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
 				 <&cru HCLK_VDPU>,
 				 <&cru HCLK_VEPU>;
 			pm_qos = <&qos_vpu>;
+			#power-domain-cells = <0>;
 		};
 
-		pd_gpu@RK3066_PD_GPU {
+		power-domain@RK3066_PD_GPU {
 			reg = <RK3066_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
+			#power-domain-cells = <0>;
 		};
 	};
 };
@@ -867,6 +872,10 @@
 	pinctrl-0 = <&uart3_xfer>;
 };
 
+&vpu {
+	power-domains = <&power RK3066_PD_VIDEO>;
+};
+
 &wdt {
 	compatible = "rockchip,rk3066-wdt", "snps,dw-wdt";
 };
diff --git a/arch/arm/boot/dts/rockchip/rk3128-evb.dts b/arch/arm/boot/dts/rockchip/rk3128-evb.dts
new file mode 100644
index 000000000000..c7ab7fcdb436
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3128-evb.dts
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+/dts-v1/;
+
+#include "rk3128.dtsi"
+
+/ {
+	model = "Rockchip RK3128 Evaluation board";
+	compatible = "rockchip,rk3128-evb", "rockchip,rk3128";
+
+	aliases {
+		mmc0 = &emmc;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x40000000>;
+	};
+
+	vcc5v0_otg: vcc5v0-otg-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc5v0_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc5v0_host";
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "xin32k";
+	};
+};
+
+&usb2phy {
+	status = "okay";
+};
+
+&usb2phy_host {
+	status = "okay";
+};
+
+&usb2phy_otg {
+	status = "okay";
+};
+
+&usb_host_ehci {
+	status = "okay";
+};
+
+&usb_host_ohci {
+	status = "okay";
+};
+
+&usb_otg {
+	vbus-supply = <&vcc5v0_otg>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb-host {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <2 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb-otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts b/arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts
new file mode 100644
index 000000000000..03a97881519a
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3128-xpi-3128.dts
@@ -0,0 +1,425 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3128.dtsi"
+
+/ {
+	model = "Geniatech XPI-3128";
+	compatible = "geniatech,xpi-3128", "rockchip,rk3128";
+
+	aliases {
+		ethernet0 = &gmac;
+		mmc0 = &emmc;
+		mmc1 = &sdmmc;
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x40000000>;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <3300000>;
+
+		button-recovery {
+			label = "Recovery";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <0>;
+		};
+	};
+
+	dc_5v: dc-5v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/*
+	 * This is a vbus-supply, which also supplies the GL852G usb hub,
+	 * thus has to be always-on
+	 */
+	host_pwr_5v: host-pwr-5v-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio3 RK_PC4 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <1500>;
+		regulator-name = "HOST_PWR_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_5v>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_drv>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio3 RK_PD2 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			gpios = <&gpio0 RK_PD2 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_BLUE>;
+			default-state = "on";
+			pinctrl-names = "default";
+			pinctrl-0 = <&power_led>;
+		};
+
+		led-spd {
+			gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_GREEN>;
+			/*
+			 * currently not allowed to be set as per
+			 * https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml
+			 * and needs to set in userspace:
+			 *
+			 * linux,default-trigger = "netdev";
+			 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&spd_led>;
+		};
+	};
+
+	mcu3v3: mcu3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "MCU3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_ddr: vcc-ddr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_DDR";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		vin-supply = <&vcc_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_io: vcc-io-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_IO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_lan: vcc-lan-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_LAN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_sd: vcc-sd-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
+		startup-delay-us = <500>;
+		regulator-name = "VCC_SD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwren>;
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_SYS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_5v>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc33_hdmi: vcc33-hdmi-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC33_HDMI";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcca_33>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcca_33: vcca-33-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCA_33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_11: vdd-11-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_11";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd11_hdmi: vdd11-hdmi-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD11_HDMI";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vdd_11>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_arm: vdd-arm-regulator {
+		compatible = "pwm-regulator";
+		regulator-name = "VDD_ARM";
+		pwms = <&pwm1 0 25000 1>;
+		pwm-supply = <&vcc_sys>;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/*
+	 * As per schematics vdd_log is minimum 900 mV, maximum 1400 mV.
+	 * Since there are HW blocks in PD_LOGIC (which are all driven by
+	 * this supply), that either do not have a driver at all or the
+	 * driver does not implement regulator support we have to make
+	 * sure here that the voltage never drops below 1050 mV.
+	 */
+	vdd_log: vdd-log-regulator {
+		compatible = "pwm-regulator";
+		regulator-name = "VDD_LOG";
+		pwms = <&pwm2 0 25000 1>;
+		pwm-dutycycle-range = <30 100>;
+		pwm-supply = <&vcc_sys>;
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-ramp-delay = <4000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	vmmc-supply = <&vcc_io>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	cap-mmc-highspeed;
+	mmc-ddr-3_3v;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&gmac {
+	clock_in_out = "output";
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+	assigned-clocks = <&cru SCLK_MAC_SRC>;
+	assigned-clock-rates= <50000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rmii_pins>;
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names = /* GPIO0 A0-A7 */
+			  "", "", "HEADER_5", "HEADER_3",
+			  "", "", "", "",
+			  /* GPIO0 B0-B7 */
+			  "HEADER_22", "HEADER_23", "", "HEADER_19",
+			  "HEADER_26", "HEADER_21", "HEADER_24", "",
+			  /* GPIO0 C0-C7 */
+			  "", "HEADER_18", "", "",
+			  "", "", "", "",
+			  /* GPIO0 D0-D7 */
+			  "HEADER_36", "", "", "",
+			  "", "", "HEADER_13", "";
+};
+
+&gpio1 {
+	gpio-line-names = /* GPIO1 A0-A7 */
+			  "HEADER_7", "HEADER_35", "HEADER_33", "HEADER_37",
+			  "HEADER_40", "HEADER_38", "", "",
+			  /* GPIO1 B0-B7 */
+			  "HEADER_11", "", "", "HEADER_29",
+			  "HEADER_31", "", "", "",
+			  /* GPIO1 C0-C7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO1 D0-D7 */
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names = /* GPIO2 A0-A7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO2 B0-B7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO2 C0-C7 */
+			  "", "", "", "",
+			  "HEADER_27", "", "", "",
+			  /* GPIO2 D0-D7 */
+			  "", "", "HEADER_8", "HEADER_10",
+			  "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names = /* GPIO3 A0-A7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO3 B0-B7 */
+			  "", "", "", "",
+			  "", "", "", "",
+			  /* GPIO3 C0-C7 */
+			  "", "HEADER_32", "", "",
+			  "", "", "", "HEADER_12",
+			  /* GPIO3 D0-D7 */
+			  "", "", "", "HEADER_15",
+			  "", "", "", "";
+};
+
+&gpu {
+	mali-supply = <&vdd_log>;
+	status = "okay";
+};
+
+&mdio {
+	phy0: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		max-speed = <100>;
+		/* T2.2.4 min. 1 us */
+		reset-assert-us = <10>;
+		/* T2.2.1 + T2.2.2 + T2.2.3 min. 6.05 us */
+		reset-deassert-us = <20>;
+		reset-gpios = <&gpio2 RK_PD0 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp83848c_rst>;
+	};
+};
+
+&pinctrl {
+	dp83848c {
+		dp83848c_rst: dp83848c-rst {
+			rockchip,pins = <2 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	ir-receiver {
+		ir_int: ir-int {
+			rockchip,pins = <3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		power_led: power-led {
+			rockchip,pins = <0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		spd_led: spd-led {
+			rockchip,pins = <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb2 {
+		host_drv: host-drv {
+			rockchip,pins = <3 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	vmmc-supply = <&vcc_sd>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det>;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb_host_ehci {
+	status = "okay";
+};
+
+&usb_otg {
+	vusb_a-supply = <&vcc_io>;
+	vusb_d-supply = <&vdd_11>;
+	status = "okay";
+};
+
+&usb2phy {
+	status = "okay";
+};
+
+&usb2phy_host {
+	status = "okay";
+};
+
+&usb2phy_otg {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rockchip/rk3128.dtsi b/arch/arm/boot/dts/rockchip/rk3128.dtsi
new file mode 100644
index 000000000000..e2264c40b924
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3128.dtsi
@@ -0,0 +1,1156 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2017 Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/clock/rk3128-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rk3128-power.h>
+
+/ {
+	compatible = "rockchip,rk3128";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "rockchip,rk3036-smp";
+
+		cpu0: cpu@f00 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+			clock-latency = <40000>;
+			clocks = <&cru ARMCLK>;
+			resets = <&cru SRST_CORE0>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+
+		cpu1: cpu@f01 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf01>;
+			resets = <&cru SRST_CORE1>;
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+
+		cpu2: cpu@f02 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf02>;
+			resets = <&cru SRST_CORE2>;
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+
+		cpu3: cpu@f03 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf03>;
+			resets = <&cru SRST_CORE3>;
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	cpu_opp_table: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-216000000 {
+			opp-hz = /bits/ 64 <216000000>;
+			opp-microvolt = <950000 950000 1325000>;
+		};
+		opp-408000000 {
+			opp-hz = /bits/ 64 <408000000>;
+			opp-microvolt = <950000 950000 1325000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <950000 950000 1325000>;
+		};
+		opp-696000000 {
+			opp-hz = /bits/ 64 <696000000>;
+			opp-microvolt = <975000 975000 1325000>;
+		};
+		opp-816000000 {
+			opp-hz = /bits/ 64 <816000000>;
+			opp-microvolt = <1075000 1075000 1325000>;
+			opp-suspend;
+		};
+		opp-1008000000 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <1200000 1200000 1325000>;
+		};
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1325000 1325000 1325000>;
+		};
+	};
+
+	gpu_opp_table: opp-table-1 {
+		compatible = "operating-points-v2";
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <975000 975000 1250000>;
+		};
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <1050000 1050000 1250000>;
+		};
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1150000 1150000 1250000>;
+		};
+		opp-480000000 {
+			opp-hz = /bits/ 64 <480000000>;
+			opp-microvolt = <1250000 1250000 1250000>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		arm,cpu-registers-not-fw-configured;
+		clock-frequency = <24000000>;
+	};
+
+	xin24m: oscillator {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xin24m";
+		#clock-cells = <0>;
+	};
+
+	imem: sram@10080000 {
+		compatible = "mmio-sram";
+		reg = <0x10080000 0x2000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x10080000 0x2000>;
+
+		smp-sram@0 {
+			compatible = "rockchip,rk3066-smp-sram";
+			reg = <0x00 0x10>;
+		};
+	};
+
+	gpu: gpu@10090000 {
+		compatible = "rockchip,rk3128-mali", "arm,mali-400";
+		reg = <0x10090000 0x10000>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "gp",
+				  "gpmmu",
+				  "pp0",
+				  "ppmmu0",
+				  "pp1",
+				  "ppmmu1";
+		clocks = <&cru ACLK_GPU>, <&cru ACLK_GPU>;
+		clock-names = "bus", "core";
+		operating-points-v2 = <&gpu_opp_table>;
+		resets = <&cru SRST_GPU>;
+		power-domains = <&power RK3128_PD_GPU>;
+		status = "disabled";
+	};
+
+	pmu: syscon@100a0000 {
+		compatible = "rockchip,rk3128-pmu", "syscon", "simple-mfd";
+		reg = <0x100a0000 0x1000>;
+
+		power: power-controller {
+			compatible = "rockchip,rk3128-power-controller";
+			#power-domain-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-domain@RK3128_PD_VIO {
+				reg = <RK3128_PD_VIO>;
+				clocks = <&cru ACLK_CIF>,
+					 <&cru HCLK_CIF>,
+					 <&cru DCLK_EBC>,
+					 <&cru HCLK_EBC>,
+					 <&cru ACLK_IEP>,
+					 <&cru HCLK_IEP>,
+					 <&cru ACLK_LCDC0>,
+					 <&cru HCLK_LCDC0>,
+					 <&cru PCLK_MIPI>,
+					 <&cru ACLK_RGA>,
+					 <&cru HCLK_RGA>,
+					 <&cru ACLK_VIO0>,
+					 <&cru ACLK_VIO1>,
+					 <&cru HCLK_VIO>,
+					 <&cru HCLK_VIO_H2P>,
+					 <&cru DCLK_VOP>,
+					 <&cru SCLK_VOP>;
+				pm_qos = <&qos_ebc>,
+					 <&qos_iep>,
+					 <&qos_lcdc>,
+					 <&qos_rga>,
+					 <&qos_vip>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3128_PD_VIDEO {
+				reg = <RK3128_PD_VIDEO>;
+				clocks = <&cru ACLK_VDPU>,
+					 <&cru HCLK_VDPU>,
+					 <&cru ACLK_VEPU>,
+					 <&cru HCLK_VEPU>,
+					 <&cru SCLK_HEVC_CORE>;
+				pm_qos = <&qos_vpu>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3128_PD_GPU {
+				reg = <RK3128_PD_GPU>;
+				clocks = <&cru ACLK_GPU>;
+				pm_qos = <&qos_gpu>;
+				#power-domain-cells = <0>;
+			};
+		};
+	};
+
+	qos_gpu: qos@1012d000 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012d000 0x20>;
+	};
+
+	qos_vpu: qos@1012e000 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012e000 0x20>;
+	};
+
+	qos_rga: qos@1012f000 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012f000 0x20>;
+	};
+
+	qos_ebc: qos@1012f080 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012f080 0x20>;
+	};
+
+	qos_iep: qos@1012f100 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012f100 0x20>;
+	};
+
+	qos_lcdc: qos@1012f180 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012f180 0x20>;
+	};
+
+	qos_vip: qos@1012f200 {
+		compatible = "rockchip,rk3128-qos", "syscon";
+		reg = <0x1012f200 0x20>;
+	};
+
+	gic: interrupt-controller@10139000 {
+		compatible = "arm,cortex-a7-gic";
+		reg = <0x10139000 0x1000>,
+		      <0x1013a000 0x1000>,
+		      <0x1013c000 0x2000>,
+		      <0x1013e000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+	};
+
+	usb_otg: usb@10180000 {
+		compatible = "rockchip,rk3128-usb", "rockchip,rk3066-usb", "snps,dwc2";
+		reg = <0x10180000 0x40000>;
+		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_OTG>;
+		clock-names = "otg";
+		dr_mode = "otg";
+		g-np-tx-fifo-size = <16>;
+		g-rx-fifo-size = <280>;
+		g-tx-fifo-size = <256 128 128 64 32 16>;
+		phys = <&usb2phy_otg>;
+		phy-names = "usb2-phy";
+		status = "disabled";
+	};
+
+	usb_host_ehci: usb@101c0000 {
+		compatible = "generic-ehci";
+		reg = <0x101c0000 0x20000>;
+		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_HOST2>;
+		phys = <&usb2phy_host>;
+		phy-names = "usb";
+		status = "disabled";
+	};
+
+	usb_host_ohci: usb@101e0000 {
+		compatible = "generic-ohci";
+		reg = <0x101e0000 0x20000>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_HOST2>;
+		phys = <&usb2phy_host>;
+		phy-names = "usb";
+		status = "disabled";
+	};
+
+	sdmmc: mmc@10214000 {
+		compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0x10214000 0x4000>;
+		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+			 <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		dmas = <&pdma 10>;
+		dma-names = "rx-tx";
+		fifo-depth = <256>;
+		max-frequency = <150000000>;
+		resets = <&cru SRST_SDMMC>;
+		reset-names = "reset";
+		status = "disabled";
+	};
+
+	sdio: mmc@10218000 {
+		compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0x10218000 0x4000>;
+		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
+			 <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		dmas = <&pdma 11>;
+		dma-names = "rx-tx";
+		fifo-depth = <256>;
+		max-frequency = <150000000>;
+		resets = <&cru SRST_SDIO>;
+		reset-names = "reset";
+		status = "disabled";
+	};
+
+	emmc: mmc@1021c000 {
+		compatible = "rockchip,rk3128-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0x1021c000 0x4000>;
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		dmas = <&pdma 12>;
+		dma-names = "rx-tx";
+		fifo-depth = <256>;
+		max-frequency = <150000000>;
+		resets = <&cru SRST_EMMC>;
+		reset-names = "reset";
+		status = "disabled";
+	};
+
+	nfc: nand-controller@10500000 {
+		compatible = "rockchip,rk3128-nfc", "rockchip,rk2928-nfc";
+		reg = <0x10500000 0x4000>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+		clock-names = "ahb", "nfc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_cs0
+			     &flash_dqs &flash_rdn &flash_rdy &flash_wrn>;
+		status = "disabled";
+	};
+
+	cru: clock-controller@20000000 {
+		compatible = "rockchip,rk3128-cru";
+		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
+		rockchip,grf = <&grf>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		assigned-clocks = <&cru PLL_GPLL>;
+		assigned-clock-rates = <594000000>;
+	};
+
+	grf: syscon@20008000 {
+		compatible = "rockchip,rk3128-grf", "syscon", "simple-mfd";
+		reg = <0x20008000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		usb2phy: usb2phy@17c {
+			compatible = "rockchip,rk3128-usb2phy";
+			reg = <0x017c 0x0c>;
+			clocks = <&cru SCLK_OTGPHY0>;
+			clock-names = "phyclk";
+			clock-output-names = "usb480m_phy";
+			assigned-clocks = <&cru SCLK_USB480M>;
+			assigned-clock-parents = <&usb2phy>;
+			#clock-cells = <0>;
+			status = "disabled";
+
+			usb2phy_host: host-port {
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "linestate";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			usb2phy_otg: otg-port {
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "otg-bvalid", "otg-id",
+						  "linestate";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	timer0: timer@20044000 {
+		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+		reg = <0x20044000 0x20>;
+		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER0>;
+		clock-names = "pclk", "timer";
+	};
+
+	timer1: timer@20044020 {
+		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+		reg = <0x20044020 0x20>;
+		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER1>;
+		clock-names = "pclk", "timer";
+	};
+
+	timer2: timer@20044040 {
+		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+		reg = <0x20044040 0x20>;
+		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER2>;
+		clock-names = "pclk", "timer";
+	};
+
+	timer3: timer@20044060 {
+		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+		reg = <0x20044060 0x20>;
+		interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER3>;
+		clock-names = "pclk", "timer";
+	};
+
+	timer4: timer@20044080 {
+		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+		reg = <0x20044080 0x20>;
+		interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER4>;
+		clock-names = "pclk", "timer";
+	};
+
+	timer5: timer@200440a0 {
+		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
+		reg = <0x200440a0 0x20>;
+		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER5>;
+		clock-names = "pclk", "timer";
+	};
+
+	watchdog: watchdog@2004c000 {
+		compatible = "rockchip,rk3128-wdt", "snps,dw-wdt";
+		reg = <0x2004c000 0x100>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_WDT>;
+		status = "disabled";
+	};
+
+	pwm0: pwm@20050000 {
+		compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+		reg = <0x20050000 0x10>;
+		clocks = <&cru PCLK_PWM>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm0_pin>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm1: pwm@20050010 {
+		compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+		reg = <0x20050010 0x10>;
+		clocks = <&cru PCLK_PWM>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm1_pin>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm2: pwm@20050020 {
+		compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+		reg = <0x20050020 0x10>;
+		clocks = <&cru PCLK_PWM>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm2_pin>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm3: pwm@20050030 {
+		compatible = "rockchip,rk3128-pwm", "rockchip,rk3288-pwm";
+		reg = <0x20050030 0x10>;
+		clocks = <&cru PCLK_PWM>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm3_pin>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	i2c1: i2c@20056000 {
+		compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+		reg = <0x20056000 0x1000>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c1_xfer>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@2005a000 {
+		compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+		reg = <0x2005a000 0x1000>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_xfer>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c3: i2c@2005e000 {
+		compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+		reg = <0x2005e000 0x1000>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c3_xfer>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	uart0: serial@20060000 {
+		compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+		reg = <0x20060000 0x100>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&pdma 2>, <&pdma 3>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart1: serial@20064000 {
+		compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+		reg = <0x20064000 0x100>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&pdma 4>, <&pdma 5>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1_xfer>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart2: serial@20068000 {
+		compatible = "rockchip,rk3128-uart", "snps,dw-apb-uart";
+		reg = <0x20068000 0x100>;
+		interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&pdma 6>, <&pdma 7>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2_xfer>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	saradc: saradc@2006c000 {
+		compatible = "rockchip,saradc";
+		reg = <0x2006c000 0x100>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
+		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
+		#io-channel-cells = <1>;
+		status = "disabled";
+	};
+
+	i2c0: i2c@20072000 {
+		compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
+		reg = <0x20072000 0x1000>;
+		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "i2c";
+		clocks = <&cru PCLK_I2C0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_xfer>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi0: spi@20074000 {
+		compatible = "rockchip,rk3128-spi", "rockchip,rk3066-spi";
+		reg = <0x20074000 0x1000>;
+		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+		clock-names = "spiclk", "apb_pclk";
+		dmas = <&pdma 8>, <&pdma 9>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi0_tx &spi0_rx &spi0_clk &spi0_cs0 &spi0_cs1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	pdma: dma-controller@20078000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x20078000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC>;
+		clock-names = "apb_pclk";
+		#dma-cells = <1>;
+	};
+
+	gmac: ethernet@2008c000 {
+		compatible = "rockchip,rk3128-gmac";
+		reg = <0x2008c000 0x4000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq", "eth_wake_irq";
+		clocks = <&cru SCLK_MAC>,
+			 <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
+			 <&cru SCLK_MAC_REF>, <&cru SCLK_MAC_REFOUT>,
+			 <&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
+		clock-names = "stmmaceth",
+			      "mac_clk_rx", "mac_clk_tx",
+			      "clk_mac_ref", "clk_mac_refout",
+			      "aclk_mac", "pclk_mac";
+		resets = <&cru SRST_GMAC>;
+		reset-names = "stmmaceth";
+		rockchip,grf = <&grf>;
+		rx-fifo-depth = <4096>;
+		tx-fifo-depth = <2048>;
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+		};
+	};
+
+	pinctrl: pinctrl {
+		compatible = "rockchip,rk3128-pinctrl";
+		rockchip,grf = <&grf>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio@2007c000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x2007c000 0x100>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO0>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@20080000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x20080000 0x100>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@20084000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x20084000 0x100>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@20088000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x20088000 0x100>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO3>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pcfg_pull_default: pcfg-pull-default {
+			bias-pull-pin-default;
+		};
+
+		pcfg_pull_none: pcfg-pull-none {
+			bias-disable;
+		};
+
+		emmc {
+			emmc_clk: emmc-clk {
+				rockchip,pins = <2 RK_PA7 2 &pcfg_pull_none>;
+			};
+
+			emmc_cmd: emmc-cmd {
+				rockchip,pins = <1 RK_PC6 2 &pcfg_pull_default>;
+			};
+
+			emmc_cmd1: emmc-cmd1 {
+				rockchip,pins = <2 RK_PA4 2 &pcfg_pull_default>;
+			};
+
+			emmc_pwr: emmc-pwr {
+				rockchip,pins = <2 RK_PA5 2 &pcfg_pull_default>;
+			};
+
+			emmc_bus1: emmc-bus1 {
+				rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>;
+			};
+
+			emmc_bus4: emmc-bus4 {
+				rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+						<1 RK_PD1 2 &pcfg_pull_default>,
+						<1 RK_PD2 2 &pcfg_pull_default>,
+						<1 RK_PD3 2 &pcfg_pull_default>;
+			};
+
+			emmc_bus8: emmc-bus8 {
+				rockchip,pins = <1 RK_PD0 2 &pcfg_pull_default>,
+						<1 RK_PD1 2 &pcfg_pull_default>,
+						<1 RK_PD2 2 &pcfg_pull_default>,
+						<1 RK_PD3 2 &pcfg_pull_default>,
+						<1 RK_PD4 2 &pcfg_pull_default>,
+						<1 RK_PD5 2 &pcfg_pull_default>,
+						<1 RK_PD6 2 &pcfg_pull_default>,
+						<1 RK_PD7 2 &pcfg_pull_default>;
+			};
+		};
+
+		gmac {
+			rgmii_pins: rgmii-pins {
+				rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+						<2 RK_PB1 3 &pcfg_pull_default>,
+						<2 RK_PB3 3 &pcfg_pull_default>,
+						<2 RK_PB4 3 &pcfg_pull_default>,
+						<2 RK_PB5 3 &pcfg_pull_default>,
+						<2 RK_PB6 3 &pcfg_pull_default>,
+						<2 RK_PC0 3 &pcfg_pull_default>,
+						<2 RK_PC1 3 &pcfg_pull_default>,
+						<2 RK_PC2 3 &pcfg_pull_default>,
+						<2 RK_PC3 3 &pcfg_pull_default>,
+						<2 RK_PD1 3 &pcfg_pull_default>,
+						<2 RK_PC4 4 &pcfg_pull_default>,
+						<2 RK_PC5 4 &pcfg_pull_default>,
+						<2 RK_PC6 4 &pcfg_pull_default>,
+						<2 RK_PC7 4 &pcfg_pull_default>;
+			};
+
+			rmii_pins: rmii-pins {
+				rockchip,pins = <2 RK_PB0 3 &pcfg_pull_default>,
+						<2 RK_PB4 3 &pcfg_pull_default>,
+						<2 RK_PB5 3 &pcfg_pull_default>,
+						<2 RK_PB6 3 &pcfg_pull_default>,
+						<2 RK_PB7 3 &pcfg_pull_default>,
+						<2 RK_PC0 3 &pcfg_pull_default>,
+						<2 RK_PC1 3 &pcfg_pull_default>,
+						<2 RK_PC2 3 &pcfg_pull_default>,
+						<2 RK_PC3 3 &pcfg_pull_default>,
+						<2 RK_PD1 3 &pcfg_pull_default>;
+			};
+		};
+
+		hdmi {
+			hdmii2c_xfer: hdmii2c-xfer {
+				rockchip,pins = <0 RK_PA6 2 &pcfg_pull_none>,
+						<0 RK_PA7 2 &pcfg_pull_none>;
+			};
+
+			hdmi_hpd: hdmi-hpd {
+				rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
+			};
+
+			hdmi_cec: hdmi-cec {
+				rockchip,pins = <0 RK_PC4 1 &pcfg_pull_none>;
+			};
+		};
+
+		i2c0 {
+			i2c0_xfer: i2c0-xfer {
+				rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>,
+						<0 RK_PA1 1 &pcfg_pull_none>;
+			};
+		};
+
+		i2c1 {
+			i2c1_xfer: i2c1-xfer {
+				rockchip,pins = <0 RK_PA2 1 &pcfg_pull_none>,
+						<0 RK_PA3 1 &pcfg_pull_none>;
+			};
+		};
+
+		i2c2 {
+			i2c2_xfer: i2c2-xfer {
+				rockchip,pins = <2 RK_PC4 3 &pcfg_pull_none>,
+						<2 RK_PC5 3 &pcfg_pull_none>;
+			};
+		};
+
+		i2c3 {
+			i2c3_xfer: i2c3-xfer {
+				rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>,
+						<0 RK_PA7 1 &pcfg_pull_none>;
+			};
+		};
+
+		i2s {
+			i2s_bus: i2s-bus {
+				rockchip,pins = <0 RK_PB0 1 &pcfg_pull_none>,
+						<0 RK_PB1 1 &pcfg_pull_none>,
+						<0 RK_PB3 1 &pcfg_pull_none>,
+						<0 RK_PB4 1 &pcfg_pull_none>,
+						<0 RK_PB5 1 &pcfg_pull_none>,
+						<0 RK_PB6 1 &pcfg_pull_none>;
+			};
+
+			i2s1_bus: i2s1-bus {
+				rockchip,pins = <1 RK_PA0 1 &pcfg_pull_none>,
+						<1 RK_PA1 1 &pcfg_pull_none>,
+						<1 RK_PA2 1 &pcfg_pull_none>,
+						<1 RK_PA3 1 &pcfg_pull_none>,
+						<1 RK_PA4 1 &pcfg_pull_none>,
+						<1 RK_PA5 1 &pcfg_pull_none>;
+			};
+		};
+
+		lcdc {
+			lcdc_dclk: lcdc-dclk {
+				rockchip,pins = <2 RK_PB0 1 &pcfg_pull_none>;
+			};
+
+			lcdc_den: lcdc-den {
+				rockchip,pins = <2 RK_PB3 1 &pcfg_pull_none>;
+			};
+
+			lcdc_hsync: lcdc-hsync {
+				rockchip,pins = <2 RK_PB1 1 &pcfg_pull_none>;
+			};
+
+			lcdc_vsync: lcdc-vsync {
+				rockchip,pins = <2 RK_PB2 1 &pcfg_pull_none>;
+			};
+
+			lcdc_rgb24: lcdc-rgb24 {
+				rockchip,pins = <2 RK_PB4 1 &pcfg_pull_none>,
+						<2 RK_PB5 1 &pcfg_pull_none>,
+						<2 RK_PB6 1 &pcfg_pull_none>,
+						<2 RK_PB7 1 &pcfg_pull_none>,
+						<2 RK_PC0 1 &pcfg_pull_none>,
+						<2 RK_PC1 1 &pcfg_pull_none>,
+						<2 RK_PC2 1 &pcfg_pull_none>,
+						<2 RK_PC3 1 &pcfg_pull_none>,
+						<2 RK_PC4 1 &pcfg_pull_none>,
+						<2 RK_PC5 1 &pcfg_pull_none>,
+						<2 RK_PC6 1 &pcfg_pull_none>,
+						<2 RK_PC7 1 &pcfg_pull_none>,
+						<2 RK_PD0 1 &pcfg_pull_none>,
+						<2 RK_PD1 1 &pcfg_pull_none>;
+			};
+		};
+
+		nfc {
+			flash_ale: flash-ale {
+				rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>;
+			};
+
+			flash_cle: flash-cle {
+				rockchip,pins = <2 RK_PA1 1 &pcfg_pull_none>;
+			};
+
+			flash_wrn: flash-wrn {
+				rockchip,pins = <2 RK_PA2 1 &pcfg_pull_none>;
+			};
+
+			flash_rdn: flash-rdn {
+				rockchip,pins = <2 RK_PA3 1 &pcfg_pull_none>;
+			};
+
+			flash_rdy: flash-rdy {
+				rockchip,pins = <2 RK_PA4 1 &pcfg_pull_none>;
+			};
+
+			flash_cs0: flash-cs0 {
+				rockchip,pins = <2 RK_PA6 1 &pcfg_pull_none>;
+			};
+
+			flash_dqs: flash-dqs {
+				rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
+			};
+
+			flash_bus8: flash-bus8 {
+				rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>,
+						<1 RK_PD1 1 &pcfg_pull_none>,
+						<1 RK_PD2 1 &pcfg_pull_none>,
+						<1 RK_PD3 1 &pcfg_pull_none>,
+						<1 RK_PD4 1 &pcfg_pull_none>,
+						<1 RK_PD5 1 &pcfg_pull_none>,
+						<1 RK_PD6 1 &pcfg_pull_none>,
+						<1 RK_PD7 1 &pcfg_pull_none>;
+			};
+		};
+
+		pwm0 {
+			pwm0_pin: pwm0-pin {
+				rockchip,pins = <0 RK_PD2 1 &pcfg_pull_none>;
+			};
+		};
+
+		pwm1 {
+			pwm1_pin: pwm1-pin {
+				rockchip,pins = <0 RK_PD3 1 &pcfg_pull_none>;
+			};
+		};
+
+		pwm2 {
+			pwm2_pin: pwm2-pin {
+				rockchip,pins = <0 RK_PD4 1 &pcfg_pull_none>;
+			};
+		};
+
+		pwm3 {
+			pwm3_pin: pwm3-pin {
+				rockchip,pins = <3 RK_PD2 1 &pcfg_pull_none>;
+			};
+		};
+
+		sdio {
+			sdio_clk: sdio-clk {
+				rockchip,pins = <1 RK_PA0 2 &pcfg_pull_none>;
+			};
+
+			sdio_cmd: sdio-cmd {
+				rockchip,pins = <0 RK_PA3 2 &pcfg_pull_default>;
+			};
+
+			sdio_pwren: sdio-pwren {
+				rockchip,pins = <0 RK_PD6 1 &pcfg_pull_default>;
+			};
+
+			sdio_bus4: sdio-bus4 {
+				rockchip,pins = <1 RK_PA1 2 &pcfg_pull_default>,
+						<1 RK_PA2 2 &pcfg_pull_default>,
+						<1 RK_PA4 2 &pcfg_pull_default>,
+						<1 RK_PA5 2 &pcfg_pull_default>;
+			};
+		};
+
+		sdmmc {
+			sdmmc_clk: sdmmc-clk {
+				rockchip,pins = <1 RK_PC0 1 &pcfg_pull_none>;
+			};
+
+			sdmmc_cmd: sdmmc-cmd {
+				rockchip,pins = <1 RK_PB7 1 &pcfg_pull_default>;
+			};
+
+			sdmmc_det: sdmmc-det {
+				rockchip,pins = <1 RK_PC1 1 &pcfg_pull_default>;
+			};
+
+			sdmmc_wp: sdmmc-wp {
+				rockchip,pins = <1 RK_PA7 1 &pcfg_pull_default>;
+			};
+
+			sdmmc_pwren: sdmmc-pwren {
+				rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_default>;
+			};
+
+			sdmmc_bus4: sdmmc-bus4 {
+				rockchip,pins = <1 RK_PC2 1 &pcfg_pull_default>,
+						<1 RK_PC3 1 &pcfg_pull_default>,
+						<1 RK_PC4 1 &pcfg_pull_default>,
+						<1 RK_PC5 1 &pcfg_pull_default>;
+			};
+		};
+
+		spdif {
+			spdif_tx: spdif-tx {
+				rockchip,pins = <3 RK_PD3 1 &pcfg_pull_none>;
+			};
+		};
+
+		spi0 {
+			spi0_clk: spi0-clk {
+				rockchip,pins = <1 RK_PB0 1 &pcfg_pull_default>;
+			};
+
+			spi0_cs0: spi0-cs0 {
+				rockchip,pins = <1 RK_PB3 1 &pcfg_pull_default>;
+			};
+
+			spi0_tx: spi0-tx {
+				rockchip,pins = <1 RK_PB1 1 &pcfg_pull_default>;
+			};
+
+			spi0_rx: spi0-rx {
+				rockchip,pins = <1 RK_PB2 1 &pcfg_pull_default>;
+			};
+
+			spi0_cs1: spi0-cs1 {
+				rockchip,pins = <1 RK_PB4 1 &pcfg_pull_default>;
+			};
+
+			spi1_clk: spi1-clk {
+				rockchip,pins = <2 RK_PA0 2 &pcfg_pull_default>;
+			};
+
+			spi1_cs0: spi1-cs0 {
+				rockchip,pins = <1 RK_PD6 3 &pcfg_pull_default>;
+			};
+
+			spi1_tx: spi1-tx {
+				rockchip,pins = <1 RK_PD5 3 &pcfg_pull_default>;
+			};
+
+			spi1_rx: spi1-rx {
+				rockchip,pins = <1 RK_PD4 3 &pcfg_pull_default>;
+			};
+
+			spi1_cs1: spi1-cs1 {
+				rockchip,pins = <1 RK_PD7 3 &pcfg_pull_default>;
+			};
+
+			spi2_clk: spi2-clk {
+				rockchip,pins = <0 RK_PB1 2 &pcfg_pull_default>;
+			};
+
+			spi2_cs0: spi2-cs0 {
+				rockchip,pins = <0 RK_PB6 2 &pcfg_pull_default>;
+			};
+
+			spi2_tx: spi2-tx {
+				rockchip,pins = <0 RK_PB3 2 &pcfg_pull_default>;
+			};
+
+			spi2_rx: spi2-rx {
+				rockchip,pins = <0 RK_PB5 2 &pcfg_pull_default>;
+			};
+		};
+
+		uart0 {
+			uart0_xfer: uart0-xfer {
+				rockchip,pins = <2 RK_PD2 2 &pcfg_pull_default>,
+						<2 RK_PD3 2 &pcfg_pull_none>;
+			};
+
+			uart0_cts: uart0-cts {
+				rockchip,pins = <2 RK_PD5 2 &pcfg_pull_none>;
+			};
+
+			uart0_rts: uart0-rts {
+				rockchip,pins = <0 RK_PC1 2 &pcfg_pull_none>;
+			};
+		};
+
+		uart1 {
+			uart1_xfer: uart1-xfer {
+				rockchip,pins = <1 RK_PB1 2 &pcfg_pull_default>,
+						<1 RK_PB2 2 &pcfg_pull_default>;
+			};
+
+			uart1_cts: uart1-cts {
+				rockchip,pins = <1 RK_PB0 2 &pcfg_pull_none>;
+			};
+
+			uart1_rts: uart1-rts {
+				rockchip,pins = <1 RK_PB3 2 &pcfg_pull_none>;
+			};
+		};
+
+		uart2 {
+			uart2_xfer: uart2-xfer {
+				rockchip,pins = <1 RK_PC2 2 &pcfg_pull_default>,
+						<1 RK_PC3 2 &pcfg_pull_none>;
+			};
+
+			uart2_cts: uart2-cts {
+				rockchip,pins = <0 RK_PD1 1 &pcfg_pull_none>;
+			};
+
+			uart2_rts: uart2-rts {
+				rockchip,pins = <0 RK_PD0 1 &pcfg_pull_none>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/rk3188-bqedison2qc.dts b/arch/arm/boot/dts/rockchip/rk3188-bqedison2qc.dts
index c8b62bbd6a4a..9312be362a7a 100644
--- a/arch/arm/boot/dts/rk3188-bqedison2qc.dts
+++ b/arch/arm/boot/dts/rockchip/rk3188-bqedison2qc.dts
@@ -7,12 +7,19 @@
 /dts-v1/;
 #include <dt-bindings/i2c/i2c.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3188.dtsi"
 
 / {
 	model = "BQ Edison2 Quad-Core";
 	compatible = "mundoreader,bq-edison2qc", "rockchip,rk3188";
 
+	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		mmc2 = &emmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x80000000>;
@@ -30,7 +37,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key &usb_int>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -39,7 +46,7 @@
 			wakeup-source;
 		};
 
-		wake_on_usb: wake-on-usb {
+		wake_on_usb: key-wake-on-usb {
 			label = "Wake-on-USB";
 			gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -58,20 +65,25 @@
 
 	lvds-encoder {
 		compatible = "ti,sn75lvds83", "lvds-encoder";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		port@0 {
-			reg = <0>;
-			lvds_in_vop0: endpoint {
-				remote-endpoint = <&vop0_out_lvds>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_in_vop0: endpoint {
+					remote-endpoint = <&vop0_out_lvds>;
+				};
 			};
-		};
 
-		port@1 {
-			reg = <1>;
-			lvds_out_panel: endpoint {
-				remote-endpoint = <&panel_in_lvds>;
+			port@1 {
+				reg = <1>;
+
+				lvds_out_panel: endpoint {
+					remote-endpoint = <&panel_in_lvds>;
+				};
 			};
 		};
 	};
@@ -465,13 +477,16 @@
 	non-removable;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd1_clk>, <&sd1_cmd>, <&sd1_bus4>;
-	vmmcq-supply = <&vccio_wl>;
+	vqmmc-supply = <&vccio_wl>;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
 	brcmf: wifi@1 {
+		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio3>;
-		interrupts = <RK_PD2 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PD2 IRQ_TYPE_NONE>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/rk3188-px3-evb.dts b/arch/arm/boot/dts/rockchip/rk3188-px3-evb.dts
index c32e1d441cf7..0a1ae689b162 100644
--- a/arch/arm/boot/dts/rk3188-px3-evb.dts
+++ b/arch/arm/boot/dts/rockchip/rk3188-px3-evb.dts
@@ -11,6 +11,11 @@
 	model = "Rockchip PX3-EVB";
 	compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
 
+	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &emmc;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
@@ -24,7 +29,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -207,7 +212,7 @@
 				regulator-name = "wl_18";
 			};
 
-			lcd_33: SWITCH_REG1 {
+			lcd_33: SWITCH_REG {
 				regulator-name = "lcd_33";
 			};
 		};
diff --git a/arch/arm/boot/dts/rk3188-radxarock.dts b/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
index c9a7f5409960..118deacd38c4 100644
--- a/arch/arm/boot/dts/rk3188-radxarock.dts
+++ b/arch/arm/boot/dts/rockchip/rk3188-radxarock.dts
@@ -11,6 +11,10 @@
 	model = "Radxa Rock";
 	compatible = "radxa,rock", "rockchip,rk3188";
 
+	aliases {
+		mmc0 = &mmc0;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x80000000>;
@@ -20,7 +24,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -33,19 +37,19 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		green {
+		green_led: led-0 {
 			label = "rock:green:user1";
 			gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		blue {
+		blue_led: led-1 {
 			label = "rock:blue:user2";
 			gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		sleep {
+		sleep_led: led-2 {
 			label = "rock:red:power";
 			gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -67,7 +71,7 @@
 		#sound-dai-cells = <0>;
 	};
 
-	ir_recv: gpio-ir-receiver {
+	ir_recv: ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
@@ -122,18 +126,21 @@
 };
 
 &emac {
-	status = "okay";
-
+	phy = <&phy0>;
+	phy-supply = <&vcc_rmii>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+	status = "okay";
 
-	phy = <&phy0>;
-	phy-supply = <&vcc_rmii>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rockchip/rk3188.dtsi
index 10ede65d90f3..44b54af0bbf9 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3188.dtsi
@@ -54,7 +54,7 @@
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -150,30 +150,28 @@
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x2000e000 0x20>;
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER3>, <&cru PCLK_TIMER3>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER3>, <&cru SCLK_TIMER3>;
+		clock-names = "pclk", "timer";
 	};
 
 	timer6: timer@200380a0 {
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x200380a0 0x20>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER6>, <&cru PCLK_TIMER0>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER6>;
+		clock-names = "pclk", "timer";
 	};
 
 	i2s0: i2s@1011a000 {
 		compatible = "rockchip,rk3188-i2s", "rockchip,rk3066-i2s";
 		reg = <0x1011a000 0x2000>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s0_bus>;
+		clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0>;
+		clock-names = "i2s_clk", "i2s_hclk";
 		dmas = <&dmac1_s 6>, <&dmac1_s 7>;
 		dma-names = "tx", "rx";
-		clock-names = "i2s_hclk", "i2s_clk";
-		clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
 		rockchip,playback-channels = <2>;
 		rockchip,capture-channels = <2>;
 		#sound-dai-cells = <0>;
@@ -184,8 +182,8 @@
 		compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif";
 		reg = <0x1011e000 0x2000>;
 		#sound-dai-cells = <0>;
-		clock-names = "hclk", "mclk";
-		clocks = <&cru HCLK_SPDIF>, <&cru SCLK_SPDIF>;
+		clocks = <&cru SCLK_SPDIF>, <&cru HCLK_SPDIF>;
+		clock-names = "mclk", "hclk";
 		dmas = <&dmac1_s 8>;
 		dma-names = "tx";
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
@@ -197,8 +195,9 @@
 	cru: clock-controller@20000000 {
 		compatible = "rockchip,rk3188-cru";
 		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
-
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 	};
@@ -216,30 +215,6 @@
 		};
 	};
 
-	usbphy: phy {
-		compatible = "rockchip,rk3188-usb-phy", "rockchip,rk3288-usb-phy";
-		rockchip,grf = <&grf>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-
-		usbphy0: usb-phy@10c {
-			#phy-cells = <0>;
-			reg = <0x10c>;
-			clocks = <&cru SCLK_OTGPHY0>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-
-		usbphy1: usb-phy@11c {
-			#phy-cells = <0>;
-			reg = <0x11c>;
-			clocks = <&cru SCLK_OTGPHY1>;
-			clock-names = "phyclk";
-			#clock-cells = <0>;
-		};
-	};
-
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3188-pinctrl";
 		rockchip,grf = <&grf>;
@@ -249,7 +224,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@2000a000 {
+		gpio0: gpio@2000a000 {
 			compatible = "rockchip,rk3188-gpio-bank0";
 			reg = <0x2000a000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -262,7 +237,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@2003c000 {
+		gpio1: gpio@2003c000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2003c000 0x100>;
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -275,7 +250,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@2003e000 {
+		gpio2: gpio@2003e000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2003e000 0x100>;
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
@@ -288,7 +263,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@20080000 {
+		gpio3: gpio@20080000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20080000 0x100>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
@@ -301,15 +276,15 @@
 			#interrupt-cells = <2>;
 		};
 
-		pcfg_pull_up: pcfg_pull_up {
+		pcfg_pull_up: pcfg-pull-up {
 			bias-pull-up;
 		};
 
-		pcfg_pull_down: pcfg_pull_down {
+		pcfg_pull_down: pcfg-pull-down {
 			bias-pull-down;
 		};
 
-		pcfg_pull_none: pcfg_pull_none {
+		pcfg_pull_none: pcfg-pull-none {
 			bias-disable;
 		};
 
@@ -404,7 +379,7 @@
 				rockchip,pins = <2 RK_PD3 1 &pcfg_pull_none>;
 			};
 
-			lcdc1_rgb24: ldcd1-rgb24 {
+			lcdc1_rgb24: lcdc1-rgb24 {
 				rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>,
 						<2 RK_PA1 1 &pcfg_pull_none>,
 						<2 RK_PA2 1 &pcfg_pull_none>,
@@ -632,7 +607,6 @@
 
 &global_timer {
 	interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
-	status = "disabled";
 };
 
 &local_timer {
@@ -664,6 +638,38 @@
 	power-domains = <&power RK3188_PD_GPU>;
 };
 
+&grf {
+	compatible = "rockchip,rk3188-grf", "syscon", "simple-mfd";
+
+	io_domains: io-domains {
+		compatible = "rockchip,rk3188-io-voltage-domain";
+		status = "disabled";
+	};
+
+	usbphy: usbphy {
+		compatible = "rockchip,rk3188-usb-phy";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		usbphy0: usb-phy@10c {
+			reg = <0x10c>;
+			clocks = <&cru SCLK_OTGPHY0>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+		};
+
+		usbphy1: usb-phy@11c {
+			reg = <0x11c>;
+			clocks = <&cru SCLK_OTGPHY1>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+		};
+	};
+};
+
 &i2c0 {
 	compatible = "rockchip,rk3188-i2c";
 	pinctrl-names = "default";
@@ -701,7 +707,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pd_vio@RK3188_PD_VIO {
+		power-domain@RK3188_PD_VIO {
 			reg = <RK3188_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -721,21 +727,24 @@
 				 <&qos_cif0>,
 				 <&qos_ipp>,
 				 <&qos_rga>;
+			#power-domain-cells = <0>;
 		};
 
-		pd_video@RK3188_PD_VIDEO {
+		power-domain@RK3188_PD_VIDEO {
 			reg = <RK3188_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
 				 <&cru HCLK_VDPU>,
 				 <&cru HCLK_VEPU>;
 			pm_qos = <&qos_vpu>;
+			#power-domain-cells = <0>;
 		};
 
-		pd_gpu@RK3188_PD_GPU {
+		power-domain@RK3188_PD_GPU {
 			reg = <RK3188_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
+			#power-domain-cells = <0>;
 		};
 	};
 };
@@ -796,6 +805,11 @@
 	pinctrl-0 = <&uart3_xfer>;
 };
 
+&vpu {
+	compatible = "rockchip,rk3188-vpu", "rockchip,rk3066-vpu";
+	power-domains = <&power RK3188_PD_VIDEO>;
+};
+
 &wdt {
 	compatible = "rockchip,rk3188-wdt", "snps,dw-wdt";
 };
diff --git a/arch/arm/boot/dts/rk3228-evb.dts b/arch/arm/boot/dts/rockchip/rk3228-evb.dts
index 5670b33fd1bd..69a5e239ed1a 100644
--- a/arch/arm/boot/dts/rk3228-evb.dts
+++ b/arch/arm/boot/dts/rockchip/rk3228-evb.dts
@@ -8,6 +8,10 @@
 	model = "Rockchip RK3228 Evaluation board";
 	compatible = "rockchip,rk3228-evb", "rockchip,rk3228";
 
+	aliases {
+		mmc0 = &emmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -46,7 +50,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy: phy@0 {
+		phy: ethernet-phy@0 {
 			compatible = "ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
 			clocks = <&cru SCLK_MAC_PHY>;
diff --git a/arch/arm/boot/dts/rk3229-evb.dts b/arch/arm/boot/dts/rockchip/rk3229-evb.dts
index 350497a3ca86..5c3d08e3eea3 100644
--- a/arch/arm/boot/dts/rk3229-evb.dts
+++ b/arch/arm/boot/dts/rockchip/rk3229-evb.dts
@@ -9,6 +9,10 @@
 	model = "Rockchip RK3229 Evaluation board";
 	compatible = "rockchip,rk3229-evb", "rockchip,rk3229";
 
+	aliases {
+		mmc0 = &emmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -103,7 +107,7 @@
 		regulator-boot-on;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/rk3229-xms6.dts b/arch/arm/boot/dts/rockchip/rk3229-xms6.dts
index 679fc2b00e5a..7bfbfd11fb55 100644
--- a/arch/arm/boot/dts/rk3229-xms6.dts
+++ b/arch/arm/boot/dts/rockchip/rk3229-xms6.dts
@@ -9,6 +9,12 @@
 	model = "Mecer Xtreme Mini S6";
 	compatible = "mecer,xms6", "rockchip,rk3229";
 
+	aliases {
+		mmc0 = &sdmmc;
+		mmc1 = &sdio;
+		mmc2 = &emmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
@@ -33,12 +39,18 @@
 	power-led {
 		compatible = "gpio-leds";
 
-		blue {
+		blue_led: led-0 {
 			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>,
+		              <&gpio2 29 GPIO_ACTIVE_LOW>;
+	};
+
 	vcc_host: vcc-host-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -131,7 +143,6 @@
 
 &emmc {
 	cap-mmc-highspeed;
-	disable-wp;
 	non-removable;
 	status = "okay";
 };
@@ -150,7 +161,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy: phy@0 {
+		phy: ethernet-phy@0 {
 			compatible = "ethernet-phy-id1234.d400",
 			             "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
@@ -202,6 +213,16 @@
 	status = "okay";
 };
 
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	vqmmc-supply = <&vccio_1v8>;
+	status = "okay";
+};
+
 &sdmmc {
 	cap-mmc-highspeed;
 	disable-wp;
diff --git a/arch/arm/boot/dts/rk3229.dtsi b/arch/arm/boot/dts/rockchip/rk3229.dtsi
index cb7d3fad8e60..c340fb30e775 100644
--- a/arch/arm/boot/dts/rk3229.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3229.dtsi
@@ -10,7 +10,7 @@
 
 	/delete-node/ opp-table0;
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rockchip/rk322x.dtsi
index 340ed6ccb08f..831561fc1814 100644
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk322x.dtsi
@@ -6,6 +6,7 @@
 #include <dt-bindings/pinctrl/rockchip.h>
 #include <dt-bindings/clock/rk3228-cru.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/power/rk3228-power.h>
 
 / {
 	#address-cells = <1>;
@@ -14,6 +15,10 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
@@ -67,7 +72,7 @@
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -95,23 +100,6 @@
 		};
 	};
 
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		pdma: pdma@110f0000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x110f0000 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			clocks = <&cru ACLK_DMAC>;
-			clock-names = "apb_pclk";
-		};
-	};
-
 	arm-pmu {
 		compatible = "arm,cortex-a7-pmu";
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
@@ -152,8 +140,6 @@
 		compatible = "rockchip,rk3228-i2s", "rockchip,rk3066-i2s";
 		reg = <0x100b0000 0x4000>;
 		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		clock-names = "i2s_clk", "i2s_hclk";
 		clocks = <&cru SCLK_I2S1>, <&cru HCLK_I2S1_8CH>;
 		dmas = <&pdma 14>, <&pdma 15>;
@@ -167,8 +153,6 @@
 		compatible = "rockchip,rk3228-i2s", "rockchip,rk3066-i2s";
 		reg = <0x100c0000 0x4000>;
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		clock-names = "i2s_clk", "i2s_hclk";
 		clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0_8CH>;
 		dmas = <&pdma 11>, <&pdma 12>;
@@ -193,8 +177,6 @@
 		compatible = "rockchip,rk3228-i2s", "rockchip,rk3066-i2s";
 		reg = <0x100e0000 0x4000>;
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		clock-names = "i2s_clk", "i2s_hclk";
 		clocks = <&cru SCLK_I2S2>, <&cru HCLK_I2S2_2CH>;
 		dmas = <&pdma 0>, <&pdma 1>;
@@ -213,7 +195,65 @@
 			status = "disabled";
 		};
 
-		u2phy0: usb2-phy@760 {
+		power: power-controller {
+			compatible = "rockchip,rk3228-power-controller";
+			#power-domain-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-domain@RK3228_PD_VIO {
+				reg = <RK3228_PD_VIO>;
+				clocks = <&cru ACLK_HDCP>,
+					 <&cru SCLK_HDCP>,
+					 <&cru ACLK_IEP>,
+					 <&cru HCLK_IEP>,
+					 <&cru ACLK_RGA>,
+					 <&cru HCLK_RGA>,
+					 <&cru SCLK_RGA>;
+				pm_qos = <&qos_hdcp>,
+					 <&qos_iep>,
+					 <&qos_rga_r>,
+					 <&qos_rga_w>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3228_PD_VOP {
+				reg = <RK3228_PD_VOP>;
+				clocks = <&cru ACLK_VOP>,
+					 <&cru DCLK_VOP>,
+					 <&cru HCLK_VOP>;
+				pm_qos = <&qos_vop>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3228_PD_VPU {
+				reg = <RK3228_PD_VPU>;
+				clocks = <&cru ACLK_VPU>,
+					 <&cru HCLK_VPU>;
+				pm_qos = <&qos_vpu>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3228_PD_RKVDEC {
+				reg = <RK3228_PD_RKVDEC>;
+				clocks = <&cru ACLK_RKVDEC>,
+					 <&cru HCLK_RKVDEC>,
+					 <&cru SCLK_VDEC_CABAC>,
+					 <&cru SCLK_VDEC_CORE>;
+				pm_qos = <&qos_rkvdec_r>,
+					 <&qos_rkvdec_w>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3228_PD_GPU {
+				reg = <RK3228_PD_GPU>;
+				clocks = <&cru ACLK_GPU>;
+				pm_qos = <&qos_gpu>;
+				#power-domain-cells = <0>;
+			};
+		};
+
+		u2phy0: usb2phy@760 {
 			compatible = "rockchip,rk3228-usb2phy";
 			reg = <0x0760 0x0c>;
 			clocks = <&cru SCLK_OTGPHY0>;
@@ -240,7 +280,7 @@
 			};
 		};
 
-		u2phy1: usb2-phy@800 {
+		u2phy1: usb2phy@800 {
 			compatible = "rockchip,rk3228-usb2phy";
 			reg = <0x0800 0x0c>;
 			clocks = <&cru SCLK_OTGPHY1>;
@@ -390,7 +430,7 @@
 	};
 
 	wdt: watchdog@110a0000 {
-		compatible = "snps,dw-wdt";
+		compatible = "rockchip,rk3228-wdt", "snps,dw-wdt";
 		reg = <0x110a0000 0x100>;
 		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru PCLK_CPU>;
@@ -402,7 +442,6 @@
 		reg = <0x110b0000 0x10>;
 		#pwm-cells = <3>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm0_pin>;
 		status = "disabled";
@@ -413,7 +452,6 @@
 		reg = <0x110b0010 0x10>;
 		#pwm-cells = <3>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm1_pin>;
 		status = "disabled";
@@ -424,7 +462,6 @@
 		reg = <0x110b0020 0x10>;
 		#pwm-cells = <3>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm2_pin>;
 		status = "disabled";
@@ -435,7 +472,6 @@
 		reg = <0x110b0030 0x10>;
 		#pwm-cells = <2>;
 		clocks = <&cru PCLK_PWM>;
-		clock-names = "pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm3_pin>;
 		status = "disabled";
@@ -445,13 +481,15 @@
 		compatible = "rockchip,rk3228-timer", "rockchip,rk3288-timer";
 		reg = <0x110c0000 0x20>;
 		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};
 
 	cru: clock-controller@110e0000 {
 		compatible = "rockchip,rk3228-cru";
 		reg = <0x110e0000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -469,6 +507,17 @@
 			<75000000>;
 	};
 
+	pdma: dma-controller@110f0000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x110f0000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC>;
+		clock-names = "apb_pclk";
+	};
+
 	thermal-zones {
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <100>; /* milliseconds */
@@ -526,10 +575,10 @@
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
 		pinctrl-names = "init", "default", "sleep";
-		pinctrl-0 = <&otp_gpio>;
+		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
-		pinctrl-2 = <&otp_gpio>;
-		#thermal-sensor-cells = <0>;
+		pinctrl-2 = <&otp_pin>;
+		#thermal-sensor-cells = <1>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
 	};
@@ -561,31 +610,55 @@
 				  "pp1",
 				  "ppmmu1";
 		clocks = <&cru ACLK_GPU>, <&cru ACLK_GPU>;
-		clock-names = "core", "bus";
+		clock-names = "bus", "core";
+		power-domains = <&power RK3228_PD_GPU>;
 		resets = <&cru SRST_GPU_A>;
 		status = "disabled";
 	};
 
+	vpu: video-codec@20020000 {
+		compatible = "rockchip,rk3228-vpu", "rockchip,rk3399-vpu";
+		reg = <0x20020000 0x800>;
+		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "vepu", "vdpu";
+		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
+		clock-names = "aclk", "hclk";
+		iommus = <&vpu_mmu>;
+		power-domains = <&power RK3228_PD_VPU>;
+	};
+
 	vpu_mmu: iommu@20020800 {
 		compatible = "rockchip,iommu";
 		reg = <0x20020800 0x100>;
 		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
-		status = "disabled";
+		power-domains = <&power RK3228_PD_VPU>;
+		#iommu-cells = <0>;
+	};
+
+	vdec: video-codec@20030000 {
+		compatible = "rockchip,rk3228-vdec", "rockchip,rk3399-vdec";
+		reg = <0x20030000 0x480>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>,
+			 <&cru SCLK_VDEC_CABAC>, <&cru SCLK_VDEC_CORE>;
+		clock-names = "axi", "ahb", "cabac", "core";
+		assigned-clocks = <&cru SCLK_VDEC_CABAC>, <&cru SCLK_VDEC_CORE>;
+		assigned-clock-rates = <300000000>, <300000000>;
+		iommus = <&vdec_mmu>;
+		power-domains = <&power RK3228_PD_RKVDEC>;
 	};
 
 	vdec_mmu: iommu@20030480 {
 		compatible = "rockchip,iommu";
 		reg = <0x20030480 0x40>, <0x200304c0 0x40>;
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vdec_mmu";
 		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
-		status = "disabled";
+		power-domains = <&power RK3228_PD_RKVDEC>;
+		#iommu-cells = <0>;
 	};
 
 	vop: vop@20050000 {
@@ -597,6 +670,7 @@
 		resets = <&cru SRST_VOP_A>, <&cru SRST_VOP_H>, <&cru SRST_VOP_D>;
 		reset-names = "axi", "ahb", "dclk";
 		iommus = <&vop_mmu>;
+		power-domains = <&power RK3228_PD_VOP>;
 		status = "disabled";
 
 		vop_out: port {
@@ -614,21 +688,32 @@
 		compatible = "rockchip,iommu";
 		reg = <0x20053f00 0x100>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
 		clock-names = "aclk", "iface";
+		power-domains = <&power RK3228_PD_VOP>;
 		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
+	rga: rga@20060000 {
+		compatible = "rockchip,rk3228-rga", "rockchip,rk3288-rga";
+		reg = <0x20060000 0x1000>;
+		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_RGA>, <&cru HCLK_RGA>, <&cru SCLK_RGA>;
+		clock-names = "aclk", "hclk", "sclk";
+		power-domains = <&power RK3228_PD_VIO>;
+		resets = <&cru SRST_RGA>, <&cru SRST_RGA_A>, <&cru SRST_RGA_H>;
+		reset-names = "core", "axi", "ahb";
+	};
+
 	iep_mmu: iommu@20070800 {
 		compatible = "rockchip,iommu";
 		reg = <0x20070800 0x100>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		power-domains = <&power RK3228_PD_VIO>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
@@ -639,8 +724,8 @@
 		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 		assigned-clocks = <&cru SCLK_HDMI_PHY>;
 		assigned-clock-parents = <&hdmi_phy>;
-		clocks = <&cru SCLK_HDMI_HDCP>, <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_CEC>;
-		clock-names = "isfr", "iahb", "cec";
+		clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>, <&cru SCLK_HDMI_CEC>;
+		clock-names = "iahb", "isfr", "cec";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hdmii2c_xfer &hdmi_hpd &hdmi_cec>;
 		resets = <&cru SRST_HDMI_P>;
@@ -662,7 +747,7 @@
 		};
 	};
 
-	sdmmc: dwmmc@30000000 {
+	sdmmc: mmc@30000000 {
 		compatible = "rockchip,rk3228-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x30000000 0x4000>;
 		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
@@ -675,7 +760,7 @@
 		status = "disabled";
 	};
 
-	sdio: dwmmc@30010000 {
+	sdio: mmc@30010000 {
 		compatible = "rockchip,rk3228-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x30010000 0x4000>;
 		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
@@ -688,7 +773,7 @@
 		status = "disabled";
 	};
 
-	emmc: dwmmc@30020000 {
+	emmc: mmc@30020000 {
 		compatible = "rockchip,rk3228-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x30020000 0x4000>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
@@ -698,7 +783,7 @@
 			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
 		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		bus-width = <8>;
-		default-sample-phase = <158>;
+		rockchip,default-sample-phase = <158>;
 		fifo-depth = <0x100>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
@@ -718,7 +803,6 @@
 		g-np-tx-fifo-size = <16>;
 		g-rx-fifo-size = <280>;
 		g-tx-fifo-size = <256 128 128 64 32 16>;
-		g-use-dma;
 		phys = <&u2phy0_otg>;
 		phy-names = "usb2-phy";
 		status = "disabled";
@@ -729,7 +813,6 @@
 		reg = <0x30080000 0x20000>;
 		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST0>, <&u2phy0>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy0_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -740,7 +823,6 @@
 		reg = <0x300a0000 0x20000>;
 		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST0>, <&u2phy0>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy0_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -751,7 +833,6 @@
 		reg = <0x300c0000 0x20000>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST1>, <&u2phy1>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy1_otg>;
 		phy-names = "usb";
 		status = "disabled";
@@ -762,7 +843,6 @@
 		reg = <0x300e0000 0x20000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST1>, <&u2phy1>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy1_otg>;
 		phy-names = "usb";
 		status = "disabled";
@@ -775,7 +855,6 @@
 		clocks = <&cru HCLK_HOST2>, <&u2phy1>;
 		phys = <&u2phy1_host>;
 		phy-names = "usb";
-		clock-names = "usbhost", "utmi";
 		status = "disabled";
 	};
 
@@ -784,7 +863,6 @@
 		reg = <0x30120000 0x20000>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST2>, <&u2phy1>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy1_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -809,6 +887,51 @@
 		status = "disabled";
 	};
 
+	qos_iep: qos@31030080 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31030080 0x20>;
+	};
+
+	qos_rga_w: qos@31030100 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31030100 0x20>;
+	};
+
+	qos_hdcp: qos@31030180 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31030180 0x20>;
+	};
+
+	qos_rga_r: qos@31030200 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31030200 0x20>;
+	};
+
+	qos_vpu: qos@31040000 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31040000 0x20>;
+	};
+
+	qos_gpu: qos@31050000 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31050000 0x20>;
+	};
+
+	qos_vop: qos@31060000 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31060000 0x20>;
+	};
+
+	qos_rkvdec_r: qos@31070000 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31070000 0x20>;
+	};
+
+	qos_rkvdec_w: qos@31070080 {
+		compatible = "rockchip,rk3228-qos", "syscon";
+		reg = <0x31070080 0x20>;
+	};
+
 	gic: interrupt-controller@32010000 {
 		compatible = "arm,gic-400";
 		interrupt-controller;
@@ -829,7 +952,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@11110000 {
+		gpio0: gpio@11110000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x11110000 0x100>;
 			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
@@ -842,7 +965,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@11120000 {
+		gpio1: gpio@11120000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x11120000 0x100>;
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
@@ -855,7 +978,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@11130000 {
+		gpio2: gpio@11130000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x11130000 0x100>;
 			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
@@ -868,7 +991,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@11140000 {
+		gpio3: gpio@11140000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x11140000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -1033,7 +1156,7 @@
 			};
 		};
 
-		spi-0 {
+		spi0 {
 			spi0_clk: spi0-clk {
 				rockchip,pins = <0 RK_PB1 2 &pcfg_pull_up>;
 			};
@@ -1051,7 +1174,7 @@
 			};
 		};
 
-		spi-1 {
+		spi1 {
 			spi1_clk: spi1-clk {
 				rockchip,pins = <0 RK_PC7 2 &pcfg_pull_up>;
 			};
@@ -1114,7 +1237,7 @@
 		};
 
 		tsadc {
-			otp_gpio: otp-gpio {
+			otp_pin: otp-pin {
 				rockchip,pins = <0 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 
diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rockchip/rk3288-evb-act8846.dts
index 80080767c365..8a635c243127 100644
--- a/arch/arm/boot/dts/rk3288-evb-act8846.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-evb-act8846.dts
@@ -4,6 +4,7 @@
 #include "rk3288-evb.dtsi"
 
 / {
+	model = "Rockchip RK3288 EVB ACT8846";
 	compatible = "rockchip,rk3288-evb-act8846", "rockchip,rk3288";
 
 	vcc_lcd: vcc-lcd {
@@ -53,7 +54,7 @@
 		vin-supply = <&vcc_sys>;
 	};
 
-	hym8563@51 {
+	rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 
diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rockchip/rk3288-evb-rk808.dts
index 16788209625b..42384ea4ca21 100644
--- a/arch/arm/boot/dts/rk3288-evb-rk808.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-evb-rk808.dts
@@ -4,6 +4,7 @@
 #include "rk3288-evb.dtsi"
 
 / {
+	model = "Rockchip RK3288 EVB RK808";
 	compatible = "rockchip,rk3288-evb-rk808", "rockchip,rk3288";
 };
 
diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rockchip/rk3288-evb.dtsi
index 2afd686b2033..382d2839cf47 100644
--- a/arch/arm/boot/dts/rk3288-evb.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-evb.dtsi
@@ -28,19 +28,19 @@
 			press-threshold-microvolt = <300000>;
 		};
 
-		menu {
+		button-menu {
 			label = "Menu";
 			linux,code = <KEY_MENU>;
 			press-threshold-microvolt = <640000>;
 		};
 
-		esc {
+		button-esc {
 			label = "Esc";
 			linux,code = <KEY_ESC>;
 			press-threshold-microvolt = <1000000>;
 		};
 
-		home  {
+		button-home  {
 			label = "Home";
 			linux,code = <KEY_HOME>;
 			press-threshold-microvolt = <1300000>;
@@ -97,7 +97,7 @@
 	};
 
 	panel: panel {
-		compatible = "lg,lp079qx1-sp0v", "simple-panel";
+		compatible = "lg,lp079qx1-sp0v";
 		backlight = <&backlight>;
 		enable-gpios = <&gpio7 RK_PA4 GPIO_ACTIVE_HIGH>;
 		pinctrl-0 = <&lcd_cs>;
@@ -118,7 +118,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -247,7 +247,7 @@
 	pinctrl-0 = <&rgmii_pins>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
 };
 
 &gpu {
diff --git a/arch/arm/boot/dts/rk3288-firefly-beta.dts b/arch/arm/boot/dts/rockchip/rk3288-firefly-beta.dts
index 135e8832141f..135e8832141f 100644
--- a/arch/arm/boot/dts/rk3288-firefly-beta.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-firefly-beta.dts
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi b/arch/arm/boot/dts/rockchip/rk3288-firefly-reload-core.dtsi
index 61435d8ee37b..36efa36b7190 100644
--- a/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-firefly-reload-core.dtsi
@@ -61,7 +61,7 @@
 	snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
 };
 
 &i2c0 {
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload.dts b/arch/arm/boot/dts/rockchip/rk3288-firefly-reload.dts
index 1574383fd2dc..a5a0826341e6 100644
--- a/arch/arm/boot/dts/rk3288-firefly-reload.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-firefly-reload.dts
@@ -27,7 +27,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
@@ -45,20 +45,20 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		power_led: led-0 {
 			gpios = <&gpio8 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "firefly:blue:power";
 			pinctrl-names = "default";
-			pinctrl-0 = <&power_led>;
+			pinctrl-0 = <&power_led_pin>;
 			panic-indicator;
 		};
 
-		work {
+		work_led: led-1 {
 			gpios = <&gpio8 RK_PA1 GPIO_ACTIVE_LOW>;
 			label = "firefly:blue:user";
 			linux,default-trigger = "rc-feedback";
 			pinctrl-names = "default";
-			pinctrl-0 = <&work_led>;
+			pinctrl-0 = <&work_led_pin>;
 		};
 	};
 
@@ -234,6 +234,7 @@
 };
 
 &saradc {
+	vref-supply = <&vcc_18>;
 	status = "okay";
 };
 
@@ -333,11 +334,11 @@
 	};
 
 	leds {
-		power_led: power-led {
+		power_led_pin: power-led-pin {
 			rockchip,pins = <8 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		work_led: work-led {
+		work_led_pin: work-led-pin {
 			rockchip,pins = <8 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
diff --git a/arch/arm/boot/dts/rk3288-firefly.dts b/arch/arm/boot/dts/rockchip/rk3288-firefly.dts
index 313459dab2e4..313459dab2e4 100644
--- a/arch/arm/boot/dts/rk3288-firefly.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-firefly.dts
diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rockchip/rk3288-firefly.dtsi
index 5e0a19004e46..3836c61cfb76 100644
--- a/arch/arm/boot/dts/rk3288-firefly.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-firefly.dtsi
@@ -49,7 +49,7 @@
 	keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
@@ -62,20 +62,20 @@
 	leds {
 		compatible = "gpio-leds";
 
-		work {
+		work_led: led-0 {
 			gpios = <&gpio8 RK_PA1 GPIO_ACTIVE_LOW>;
 			label = "firefly:blue:user";
 			linux,default-trigger = "rc-feedback";
 			pinctrl-names = "default";
-			pinctrl-0 = <&work_led>;
+			pinctrl-0 = <&work_led_pin>;
 		};
 
-		power {
+		power_led: led-1 {
 			gpios = <&gpio8 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "firefly:green:power";
 			linux,default-trigger = "default-on";
 			pinctrl-names = "default";
-			pinctrl-0 = <&power_led>;
+			pinctrl-0 = <&power_led_pin>;
 		};
 	};
 
@@ -191,7 +191,7 @@
 	snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
 };
 
 &gpu {
@@ -233,11 +233,10 @@
 		vin-supply = <&vcc_sys>;
 	};
 
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 		interrupt-parent = <&gpio7>;
 		interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
@@ -429,11 +428,11 @@
 	};
 
 	leds {
-		power_led: power-led {
+		power_led_pin: power-led-pin {
 			rockchip,pins = <8 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		work_led: work-led {
+		work_led_pin: work-led-pin {
 			rockchip,pins = <8 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
diff --git a/arch/arm/boot/dts/rk3288-miqi.dts b/arch/arm/boot/dts/rockchip/rk3288-miqi.dts
index c41d012c8850..db1eb648e0e1 100644
--- a/arch/arm/boot/dts/rk3288-miqi.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-miqi.dts
@@ -30,7 +30,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		work {
+		work_led: led-0 {
 			gpios = <&gpio7 RK_PA2 GPIO_ACTIVE_HIGH>;
 			label = "miqi:green:user";
 			linux,default-trigger = "timer";
@@ -81,7 +81,19 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_cpu>;
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
 };
 
 &emmc {
@@ -108,7 +120,12 @@
 	snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
 };
 
 &hdmi {
@@ -145,11 +162,10 @@
 		vin-supply = <&vcc_sys>;
 	};
 
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 	};
 
diff --git a/arch/arm/boot/dts/rk3288-phycore-rdk.dts b/arch/arm/boot/dts/rockchip/rk3288-phycore-rdk.dts
index 1e33859de484..1a5156951492 100644
--- a/arch/arm/boot/dts/rk3288-phycore-rdk.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-phycore-rdk.dts
@@ -20,14 +20,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_button_pins>;
 
-		button@0 {
+		button-0 {
 			label = "home";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>;
 			wakeup-source;
 		};
 
-		button@1 {
+		button-1 {
 			label = "menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/rk3288-phycore-som.dtsi b/arch/arm/boot/dts/rockchip/rk3288-phycore-som.dtsi
index 77a47b9b756d..e43887c9635f 100644
--- a/arch/arm/boot/dts/rk3288-phycore-som.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-phycore-som.dtsi
@@ -36,9 +36,9 @@
 	leds: user-leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&user_led>;
+		pinctrl-0 = <&user_led_pin>;
 
-		user {
+		user_led: led-0 {
 			label = "green_led";
 			gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -372,7 +372,7 @@
 	};
 
 	leds {
-		user_led: user-led {
+		user_led_pin: user-led-pin {
 			rockchip,pins = <7 RK_PA2 RK_FUNC_GPIO &pcfg_output_high>;
 		};
 	};
diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rockchip/rk3288-popmetal.dts
index 6a51940398b5..fd90f3b8fc32 100644
--- a/arch/arm/boot/dts/rk3288-popmetal.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-popmetal.dts
@@ -30,7 +30,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -103,7 +103,19 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_cpu>;
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
 };
 
 &emmc {
@@ -149,7 +161,7 @@
 	pinctrl-0 = <&rgmii_pins>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
 };
 
 &hdmi {
diff --git a/arch/arm/boot/dts/rk3288-r89.dts b/arch/arm/boot/dts/rockchip/rk3288-r89.dts
index a6ffc381abaa..633e5a032463 100644
--- a/arch/arm/boot/dts/rk3288-r89.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-r89.dts
@@ -9,6 +9,7 @@
 #include "rk3288.dtsi"
 
 / {
+	model = "Netxeon R89";
 	compatible = "netxeon,r89", "rockchip,rk3288";
 
 	memory@0 {
@@ -30,7 +31,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -90,7 +91,19 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_cpu>;
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
 };
 
 &gmac {
@@ -106,7 +119,7 @@
 	pinctrl-0 = <&rgmii_pins>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
 };
 
 &hdmi {
diff --git a/arch/arm/boot/dts/rockchip/rk3288-rock-pi-n8.dts b/arch/arm/boot/dts/rockchip/rk3288-rock-pi-n8.dts
new file mode 100644
index 000000000000..673466d264be
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3288-rock-pi-n8.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2019 Vamrs Limited
+ * Copyright (c) 2019 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "rk3288.dtsi"
+#include <arm/rockchip/rockchip-radxa-dalang-carrier.dtsi>
+#include "rk3288-vmarc-som.dtsi"
+
+/ {
+	model = "Radxa ROCK Pi N8";
+	compatible = "radxa,rockpi-n8", "vamrs,rk3288-vmarc-som",
+		     "rockchip,rk3288";
+};
diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi b/arch/arm/boot/dts/rockchip/rk3288-rock2-som.dtsi
index 44bb5e6f83b1..76363b8afcb9 100644
--- a/arch/arm/boot/dts/rk3288-rock2-som.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-rock2-som.dtsi
@@ -218,7 +218,7 @@
 	flash0-supply = <&vcc_flash>;
 	flash1-supply = <&vccio_pmu>;
 	gpio30-supply = <&vccio_pmu>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
diff --git a/arch/arm/boot/dts/rk3288-rock2-square.dts b/arch/arm/boot/dts/rockchip/rk3288-rock2-square.dts
index cdcdc921ee09..13cfdaa95cc7 100644
--- a/arch/arm/boot/dts/rk3288-rock2-square.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-rock2-square.dts
@@ -28,7 +28,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
@@ -41,13 +41,13 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		heartbeat {
+		heartbeat_led: led-0 {
 			gpios = <&gpio7 RK_PB7 GPIO_ACTIVE_LOW>;
 			label = "rock2:green:state1";
 			linux,default-trigger = "heartbeat";
 		};
 
-		mmc {
+		mmc_led: led-1 {
 			gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_LOW>;
 			label = "rock2:blue:state2";
 			linux,default-trigger = "mmc0";
@@ -156,7 +156,7 @@
 };
 
 &gmac {
-	status = "ok";
+	status = "okay";
 };
 
 &hdmi {
@@ -165,11 +165,10 @@
 };
 
 &i2c0 {
-	hym8563: hym8563@51 {
+	hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
 		clock-output-names = "xin32k";
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
diff --git a/arch/arm/boot/dts/rk3288-tinker-s.dts b/arch/arm/boot/dts/rockchip/rk3288-tinker-s.dts
index 970e13859198..970e13859198 100644
--- a/arch/arm/boot/dts/rk3288-tinker-s.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-tinker-s.dts
diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rockchip/rk3288-tinker.dts
index 1e43527aa196..1e43527aa196 100644
--- a/arch/arm/boot/dts/rk3288-tinker.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-tinker.dts
diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rockchip/rk3288-tinker.dtsi
index 0aeef23ca3db..09618bb7d872 100644
--- a/arch/arm/boot/dts/rk3288-tinker.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-tinker.dtsi
@@ -26,14 +26,12 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		button@0 {
+		button {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -46,17 +44,17 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		act-led {
+		act_led: led-0 {
 			gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
 		};
 
-		heartbeat-led {
+		heartbeat_led: led-1 {
 			gpios = <&gpio1 RK_PD1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		pwr-led {
+		pwr_led: led-2 {
 			gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
@@ -113,6 +111,17 @@
 	cpu0-supply = <&vdd_cpu>;
 };
 
+&cpu_opp_table {
+	opp-1704000000 {
+		opp-hz = /bits/ 64 <1704000000>;
+		opp-microvolt = <1350000>;
+	};
+	opp-1800000000 {
+		opp-hz = /bits/ 64 <1800000000>;
+		opp-microvolt = <1400000>;
+	};
+};
+
 &gmac {
 	assigned-clocks = <&cru SCLK_MAC>;
 	assigned-clock-parents = <&ext_gmac>;
@@ -126,7 +135,7 @@
 	snps,reset-delays-us = <0 10000 1000000>;
 	tx_delay = <0x30>;
 	rx_delay = <0x10>;
-	status = "ok";
+	status = "okay";
 };
 
 &gpu {
@@ -175,7 +184,7 @@
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt = <1350000>;
+				regulator-max-microvolt = <1400000>;
 				regulator-name = "vdd_arm";
 				regulator-ramp-delay = <6000>;
 				regulator-state-mem {
@@ -265,6 +274,7 @@
 			};
 
 			vccio_sd: LDO_REG5 {
+				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-analog-audio.dtsi b/arch/arm/boot/dts/rockchip/rk3288-veyron-analog-audio.dtsi
index 51208d161d65..51208d161d65 100644
--- a/arch/arm/boot/dts/rk3288-veyron-analog-audio.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-analog-audio.dtsi
diff --git a/arch/arm/boot/dts/rk3288-veyron-brain.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-brain.dts
index 406146cbff29..aa33d09184ad 100644
--- a/arch/arm/boot/dts/rk3288-veyron-brain.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-brain.dts
@@ -7,6 +7,7 @@
 
 /dts-v1/;
 #include "rk3288-veyron.dtsi"
+#include "rk3288-veyron-broadcom-bluetooth.dtsi"
 
 / {
 	model = "Google Brain";
@@ -40,6 +41,14 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+	>;
+
 	hdmi {
 		vcc50_hdmi_en: vcc50-hdmi-en {
 			rockchip,pins = <7 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
diff --git a/arch/arm/boot/dts/rockchip/rk3288-veyron-broadcom-bluetooth.dtsi b/arch/arm/boot/dts/rockchip/rk3288-veyron-broadcom-bluetooth.dtsi
new file mode 100644
index 000000000000..f9dde0eef527
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-broadcom-bluetooth.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Veyron (and derivatives) fragment for the Broadcom 43450 bluetooth
+ * chip.
+ *
+ * Copyright 2019 Google, Inc
+ */
+
+&uart0 {
+	bluetooth {
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>, <&bt_enable_l>,
+			    <&bt_dev_wake>;
+
+		compatible = "brcm,bcm43540-bt";
+		host-wakeup-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+		max-speed = <3000000>;
+		brcm,bt-pcm-int-params = [01 02 00 01 01];
+	};
+};
diff --git a/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi b/arch/arm/boot/dts/rockchip/rk3288-veyron-chromebook.dtsi
index ffb60f880b39..092316be67f7 100644
--- a/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-chromebook.dtsi
@@ -32,7 +32,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&ap_lid_int_l>;
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
 			wakeup-source;
@@ -136,27 +136,6 @@
 };
 
 &pinctrl {
-	pinctrl-0 = <
-		/* Common for sleep and wake, but no owners */
-		&ddr0_retention
-		&ddrio_pwroff
-		&global_pwroff
-
-		/* Wake only */
-		&suspend_l_wake
-		&bt_dev_wake_awake
-	>;
-	pinctrl-1 = <
-		/* Common for sleep and wake, but no owners */
-		&ddr0_retention
-		&ddrio_pwroff
-		&global_pwroff
-
-		/* Sleep only */
-		&suspend_l_sleep
-		&bt_dev_wake_sleep
-	>;
-
 	buttons {
 		ap_lid_int_l: ap-lid-int-l {
 			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
@@ -202,4 +181,4 @@
 	};
 };
 
-#include "cros-ec-keyboard.dtsi"
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/rk3288-veyron-edp.dtsi b/arch/arm/boot/dts/rockchip/rk3288-veyron-edp.dtsi
index 300a7e32c978..32c0f10765dd 100644
--- a/arch/arm/boot/dts/rk3288-veyron-edp.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-edp.dtsi
@@ -54,7 +54,7 @@
 	};
 
 	panel: panel {
-		compatible = "innolux,n116bge", "simple-panel";
+		compatible = "innolux,n116bge";
 		status = "okay";
 		power-supply = <&panel_regulator>;
 		backlight = <&backlight>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-fievel.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-fievel.dts
index 9a0f55085839..309b122b4d0d 100644
--- a/arch/arm/boot/dts/rk3288-veyron-fievel.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-fievel.dts
@@ -18,8 +18,6 @@
 		     "google,veyron-fievel-rev0", "google,veyron-fievel",
 		     "google,veyron", "rockchip,rk3288";
 
-	/delete-node/ bt-activity;
-
 	vccsys: vccsys {
 		compatible = "regulator-fixed";
 		regulator-name = "vccsys";
@@ -215,7 +213,11 @@
 			  "PHY_PMEB",
 
 			  "PHY_INT",
-			  "REC_MODE_L",
+			  /*
+			   * RECOVERY_SW_L is Chrome OS ABI.  Schematics call
+			   * it REC_MODE_L.
+			   */
+			  "RECOVERY_SW_L",
 			  "OTP_OUT",
 			  "",
 			  "USB_OTG_POWER_EN",
@@ -382,7 +384,11 @@
 			  "PWR_LED1",
 			  "TPM_INT_H",
 			  "SPK_ON",
-			  "FW_WP_AP",
+			  /*
+			   * AP_FLASH_WP_L is Chrome OS ABI.  Schematics call
+			   * it FW_WP_AP.
+			   */
+			  "AP_FLASH_WP_L",
 			  "",
 
 			  "CPU_NMI",
diff --git a/arch/arm/boot/dts/rk3288-veyron-jaq.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-jaq.dts
index a4966e505a2f..0d4c50e05558 100644
--- a/arch/arm/boot/dts/rk3288-veyron-jaq.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-jaq.dts
@@ -8,7 +8,7 @@
 /dts-v1/;
 
 #include "rk3288-veyron-chromebook.dtsi"
-#include "cros-ec-sbs.dtsi"
+#include "../cros-ec-sbs.dtsi"
 
 / {
 	model = "Google Jaq";
@@ -20,7 +20,7 @@
 
 &backlight {
 	/* Jaq panel PWM must be >= 3%, so start non-zero brightness at 8 */
-	brightness-levels = <0 8 255>;
+	brightness-levels = <8 255>;
 	num-interpolated-steps = <247>;
 };
 
@@ -44,10 +44,25 @@
 	};
 };
 
+&sdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	btmrvl: btmrvl@2 {
+		compatible = "marvell,sd8897-bt";
+		reg = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <RK_PD7 IRQ_TYPE_LEVEL_LOW>;
+		marvell,wakeup-pin = /bits/ 16 <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>;
+	};
+};
+
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 
@@ -273,6 +288,28 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Wake only */
+		&suspend_l_wake
+		&bt_dev_wake_awake
+	>;
+	pinctrl-1 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Sleep only */
+		&suspend_l_sleep
+		&bt_dev_wake_sleep
+	>;
+
 	buck-5v {
 		drv_5v: drv-5v {
 			rockchip,pins = <7 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-jerry.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-jerry.dts
index a6ee44f0fe13..6894763979f0 100644
--- a/arch/arm/boot/dts/rk3288-veyron-jerry.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-jerry.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 #include "rk3288-veyron-chromebook.dtsi"
-#include "cros-ec-sbs.dtsi"
+#include "../cros-ec-sbs.dtsi"
 
 / {
 	model = "Google Jerry";
@@ -192,7 +192,7 @@
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 
@@ -418,6 +418,28 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Wake only */
+		&suspend_l_wake
+		&bt_dev_wake_awake
+	>;
+	pinctrl-1 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Sleep only */
+		&suspend_l_sleep
+		&bt_dev_wake_sleep
+	>;
+
 	buck-5v {
 		drv_5v: drv-5v {
 			rockchip,pins = <7 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-mickey.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-mickey.dts
index 06a6a9554c48..ffd1121d19be 100644
--- a/arch/arm/boot/dts/rk3288-veyron-mickey.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-mickey.dts
@@ -7,6 +7,7 @@
 
 /dts-v1/;
 #include "rk3288-veyron.dtsi"
+#include "rk3288-veyron-broadcom-bluetooth.dtsi"
 
 / {
 	model = "Google Mickey";
@@ -411,6 +412,14 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+	>;
+
 	hdmi {
 		power_hdmi_on: power-hdmi-on {
 			rockchip,pins = <7 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-mighty.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-mighty.dts
index 27fbc07476d2..fa695a88f236 100644
--- a/arch/arm/boot/dts/rk3288-veyron-mighty.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-mighty.dts
@@ -18,8 +18,8 @@
 };
 
 &sdmmc {
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
-			&sdmmc_wp_gpio &sdmmc_bus4>;
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
+			&sdmmc_wp_pin &sdmmc_bus4>;
 	wp-gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>;
 
 	/delete-property/ disable-wp;
@@ -27,7 +27,7 @@
 
 &pinctrl {
 	sdmmc {
-		sdmmc_wp_gpio: sdmmc-wp-gpio {
+		sdmmc_wp_pin: sdmmc-wp-pin {
 			rockchip,pins = <7 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
diff --git a/arch/arm/boot/dts/rk3288-veyron-minnie.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-minnie.dts
index c833716dbe48..dcdcc55c4098 100644
--- a/arch/arm/boot/dts/rk3288-veyron-minnie.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-minnie.dts
@@ -7,6 +7,7 @@
 
 /dts-v1/;
 #include "rk3288-veyron-chromebook.dtsi"
+#include "rk3288-veyron-broadcom-bluetooth.dtsi"
 
 / {
 	model = "Google Minnie";
@@ -20,14 +21,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&volum_down_l &volum_up_l>;
 
-		volum_down {
+		key-volum-down {
 			label = "Volum_down";
 			gpios = <&gpio5 RK_PB3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <100>;
 		};
 
-		volum_up {
+		key-volum-up {
 			label = "Volum_up";
 			gpios = <&gpio5 RK_PB2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -38,7 +39,7 @@
 
 &backlight {
 	/* Minnie panel PWM must be >= 1%, so start non-zero brightness at 3 */
-	brightness-levels = <0 3 255>;
+	brightness-levels = <3 255>;
 	num-interpolated-steps = <252>;
 };
 
@@ -70,7 +71,7 @@
 };
 
 &panel {
-	compatible = "auo,b101ean01", "simple-panel";
+	compatible = "auo,b101ean01";
 
 	/delete-node/ panel-timing;
 
@@ -113,7 +114,7 @@
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 
@@ -344,6 +345,26 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Wake only */
+		&suspend_l_wake
+	>;
+	pinctrl-1 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Sleep only */
+		&suspend_l_sleep
+	>;
+
 	buck-5v {
 		drv_5v: drv-5v {
 			rockchip,pins = <7 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-pinky.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-pinky.dts
index f420499f300a..6337238891eb 100644
--- a/arch/arm/boot/dts/rk3288-veyron-pinky.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-pinky.dts
@@ -7,7 +7,7 @@
 
 /dts-v1/;
 #include "rk3288-veyron-chromebook.dtsi"
-#include "cros-ec-sbs.dtsi"
+#include "../cros-ec-sbs.dtsi"
 
 / {
 	model = "Google Pinky";
@@ -45,7 +45,7 @@
 &lid_switch {
 	pinctrl-0 = <&pwr_key_h &ap_lid_int_l>;
 
-	power {
+	key-power {
 		gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
 	};
 };
@@ -64,6 +64,28 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Wake only */
+		&suspend_l_wake
+		&bt_dev_wake_awake
+	>;
+	pinctrl-1 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Sleep only */
+		&suspend_l_sleep
+		&bt_dev_wake_sleep
+	>;
+
 	/delete-node/ lcd;
 
 	backlight {
@@ -83,7 +105,7 @@
 	};
 
 	sdmmc {
-		sdmmc_wp_gpio: sdmmc-wp-gpio {
+		sdmmc_wp_pin: sdmmc-wp-pin {
 			rockchip,pins = <7 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
@@ -104,8 +126,8 @@
 
 &sdmmc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
-		     &sdmmc_wp_gpio &sdmmc_bus4>;
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
+		     &sdmmc_wp_pin &sdmmc_bus4>;
 	wp-gpios = <&gpio7 RK_PB2 GPIO_ACTIVE_HIGH>;
 };
 
diff --git a/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi b/arch/arm/boot/dts/rockchip/rk3288-veyron-sdmmc.dtsi
index fe950f9863e8..8b58773e592e 100644
--- a/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-sdmmc.dtsi
@@ -5,6 +5,12 @@
  * Copyright 2015 Google, Inc
  */
 
+/ {
+	aliases {
+		mmc1 = &sdmmc;
+	};
+};
+
 &io_domains {
 	sdcard-supply = <&vccio_sd>;
 };
@@ -41,7 +47,7 @@
 		};
 
 		/* This is where we actually hook up CD */
-		sdmmc_cd_gpio: sdmmc-cd-gpio {
+		sdmmc_cd_pin: sdmmc-cd-pin {
 			rockchip,pins = <7 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
diff --git a/arch/arm/boot/dts/rk3288-veyron-speedy.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-speedy.dts
index 2f2989bc3f9c..336cd2be5265 100644
--- a/arch/arm/boot/dts/rk3288-veyron-speedy.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-speedy.dts
@@ -7,7 +7,8 @@
 
 /dts-v1/;
 #include "rk3288-veyron-chromebook.dtsi"
-#include "cros-ec-sbs.dtsi"
+#include "rk3288-veyron-broadcom-bluetooth.dtsi"
+#include "../cros-ec-sbs.dtsi"
 
 / {
 	model = "Google Speedy";
@@ -53,7 +54,7 @@
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 
@@ -279,6 +280,26 @@
 };
 
 &pinctrl {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Wake only */
+		&suspend_l_wake
+	>;
+	pinctrl-1 = <
+		/* Common for sleep and wake, but no owners */
+		&ddr0_retention
+		&ddrio_pwroff
+		&global_pwroff
+
+		/* Sleep only */
+		&suspend_l_sleep
+	>;
+
 	buck-5v {
 		drv_5v: drv-5v {
 			rockchip,pins = <7 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-tiger.dts b/arch/arm/boot/dts/rockchip/rk3288-veyron-tiger.dts
index bebb230e592f..52a84cbe7a90 100644
--- a/arch/arm/boot/dts/rk3288-veyron-tiger.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron-tiger.dts
@@ -23,7 +23,7 @@
 
 &backlight {
 	/* Tiger panel PWM must be >= 1%, so start non-zero brightness at 3 */
-	brightness-levels = <0 3 255>;
+	brightness-levels = <3 255>;
 	num-interpolated-steps = <252>;
 };
 
@@ -53,7 +53,7 @@
 };
 
 &panel {
-	compatible = "auo,b101ean01", "simple-panel";
+	compatible = "auo,b101ean01";
 
 	/delete-node/ panel-timing;
 
diff --git a/arch/arm/boot/dts/rk3288-veyron.dtsi b/arch/arm/boot/dts/rockchip/rk3288-veyron.dtsi
index 7525e3dd1fc1..d838bf0d5d9a 100644
--- a/arch/arm/boot/dts/rk3288-veyron.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288-veyron.dtsi
@@ -10,6 +10,10 @@
 #include "rk3288.dtsi"
 
 / {
+	aliases {
+		mmc0 = &emmc;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
@@ -23,37 +27,13 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
-	bt_activity: bt-activity {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&bt_host_wake>;
-
-		/*
-		 * HACK: until we have an LPM driver, we'll use an
-		 * ugly GPIO key to allow Bluetooth to wake from S3.
-		 * This is expected to only be used by BT modules that
-		 * use UART for comms.  For BT modules that talk over
-		 * SDIO we should use a wakeup mechanism related to SDIO.
-		 *
-		 * Use KEY_RESERVED here since that will work as a wakeup but
-		 * doesn't get reported to higher levels (so doesn't confuse
-		 * Chrome).
-		 */
-		bt-wake {
-			label = "BT Wakeup";
-			gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_RESERVED>;
-			wakeup-source;
-		};
-
-	};
 
 	power_button: power-button {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key_l>;
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -82,22 +62,17 @@
 		clocks = <&rk808 RK808_CLKOUT1>;
 		clock-names = "ext_clock";
 		pinctrl-names = "default";
-		pinctrl-0 = <&bt_enable_l>, <&wifi_enable_h>;
+		pinctrl-0 = <&wifi_enable_h>;
 
 		/*
-		 * Depending on the actual card populated GPIO4 D4 and D5
+		 * Depending on the actual card populated GPIO4 D4
 		 * correspond to one of these signals on the module:
 		 *
 		 * D4:
 		 * - SDIO_RESET_L_WL_REG_ON
 		 * - PDN (power down when low)
-		 *
-		 * D5:
-		 * - BT_I2S_WS_BT_RFDISABLE_L
-		 * - No connect
 		 */
-		reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>,
-			      <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
 	};
 
 	vcc_5v: vcc-5v {
@@ -481,26 +456,6 @@
 };
 
 &pinctrl {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <
-		/* Common for sleep and wake, but no owners */
-		&ddr0_retention
-		&ddrio_pwroff
-		&global_pwroff
-
-		/* Wake only */
-		&bt_dev_wake_awake
-	>;
-	pinctrl-1 = <
-		/* Common for sleep and wake, but no owners */
-		&ddr0_retention
-		&ddrio_pwroff
-		&global_pwroff
-
-		/* Sleep only */
-		&bt_dev_wake_sleep
-	>;
-
 	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
 		bias-disable;
 		drive-strength = <8>;
@@ -622,6 +577,10 @@
 		bt_dev_wake_awake: bt-dev-wake-awake {
 			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_output_high>;
 		};
+
+		bt_dev_wake: bt-dev-wake {
+			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
 	};
 
 	tpm {
diff --git a/arch/arm/boot/dts/rockchip/rk3288-vmarc-som.dtsi b/arch/arm/boot/dts/rockchip/rk3288-vmarc-som.dtsi
new file mode 100644
index 000000000000..793951655b73
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rk3288-vmarc-som.dtsi
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2019 Vamrs Limited
+ * Copyright (c) 2019 Amarula Solutions(India)
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+/ {
+	compatible = "vamrs,rk3288-vmarc-som", "rockchip,rk3288";
+
+	vccio_flash: vccio-flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vccio_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vccio_flash>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	phy-supply = <&vcc_io>;
+	snps,reset-gpio = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec_c0>;
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc_io>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc5v0_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-ramp-delay = <6000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_tp: LDO_REG1 {
+				regulator-name = "vcc_tp";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_codec: LDO_REG2 {
+				regulator-name = "vcca_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_wl: LDO_REG4 {
+				regulator-name = "vcc_wl";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-name = "vcc_18";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG8 {
+				regulator-name = "vcc18_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_sd: SWITCH_REG1 {
+				regulator-name = "vcc_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-name = "vcc_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <RK_PC3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <0>;
+		clock-output-names = "hym8563";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&io_domains {
+	bb-supply = <&vcc_io>;
+	flash0-supply = <&vccio_flash>;
+	gpio1830-supply = <&vcc_18>;
+	gpio30-supply = <&vcc_io>;
+	sdcard-supply = <&vccio_sd>;
+	wifi-supply = <&vcc_wl>;
+	status = "okay";
+};
+
+&pinctrl {
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <5 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins =
+				<6 RK_PC0 1 &pcfg_pull_up_drv_8ma>,
+				<6 RK_PC1 1 &pcfg_pull_up_drv_8ma>,
+				<6 RK_PC2 1 &pcfg_pull_up_drv_8ma>,
+				<6 RK_PC3 1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 RK_PC4 1 &pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 RK_PC5 1 &pcfg_pull_up_drv_8ma>;
+		};
+	};
+
+	vbus_host {
+		usb1_en_oc: usb1-en-oc {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	vbus_typec {
+		usb0_en_oc: usb0-en-oc {
+			rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&sdio_pwrseq {
+	/*
+	 * On the module itself this is one of these (depending
+	 * on the actual card populated):
+	 * - SDIO_RESET_L_WL_REG_ON
+	 * - PDN (power down when low)
+	 */
+	reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;	/* WIFI_REG_ON */
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&vbus_host {
+	enable-active-high;
+	gpio = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>; /* USB1_EN_OC# */
+};
+
+&vbus_typec {
+	enable-active-high;
+	gpio = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; /* USB0_EN_OC# */
+};
diff --git a/arch/arm/boot/dts/rk3288-vyasa.dts b/arch/arm/boot/dts/rockchip/rk3288-vyasa.dts
index ba06e9f97ddc..b156a83eb7d7 100644
--- a/arch/arm/boot/dts/rk3288-vyasa.dts
+++ b/arch/arm/boot/dts/rockchip/rk3288-vyasa.dts
@@ -78,6 +78,18 @@
 		vin-supply = <&vcc_io>;
 	};
 
+	vcc50_hdmi: vcc50-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc50_hdmi";
+		enable-active-high;
+		gpio = <&gpio7 RK_PB4 GPIO_ACTIVE_HIGH>; /* HDMI_EN */
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc50_hdmi_en>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vsus_5v>;
+	};
+
 	vusb1_5v: vusb1-5v {
 		compatible = "regulator-fixed";
 		regulator-name = "vusb1_5v";
@@ -87,8 +99,6 @@
 		pinctrl-0 = <&otg_vbus_drv>;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		regulator-boot-on;
 		vin-supply = <&vsus_5v>;
 	};
 
@@ -115,7 +125,19 @@
 };
 
 &cpu0 {
-	cpu0-supply = <&vdd_cpu>;
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
 };
 
 &emmc {
@@ -150,7 +172,7 @@
 };
 
 &hdmi {
-	ddc-i2c-bus = <&i2c2>;
+	ddc-i2c-bus = <&i2c5>;
 	status = "okay";
 };
 
@@ -286,15 +308,15 @@
 				};
 			};
 
-			vcc10_lcd: LDO_REG6 {
-				regulator-name = "vcc10_lcd";
+			vdd10_lcd: LDO_REG6 {
+				regulator-name = "vdd10_lcd";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-state-mem {
 					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <1800000>;
+					regulator-suspend-microvolt = <1000000>;
 				};
 			};
 
@@ -347,7 +369,7 @@
 	};
 };
 
-&i2c2 {
+&i2c5 {
 	status = "okay";
 };
 
@@ -357,10 +379,10 @@
 	audio-supply = <&vcc_18>;
 	bb-supply = <&vcc_io>;
 	dvp-supply = <&vcc_io>;
-	flash0-suuply = <&vcc_18>;
+	flash0-supply = <&vcc_18>;
 	flash1-supply = <&vcc_lan>;
 	gpio30-supply = <&vcc_io>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
@@ -404,6 +426,7 @@
 };
 
 &usb_otg {
+	vbus-supply = <&vusb1_5v>;
 	status = "okay";
 };
 
@@ -446,6 +469,12 @@
 		};
 	};
 
+	hdmi {
+		vcc50_hdmi_en: vcc50-hdmi-en {
+			rockchip,pins = <7 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		pmic_int: pmic-int {
 			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rockchip/rk3288.dtsi
index 415c75f5783c..ead343dc3df1 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3288.dtsi
@@ -7,7 +7,6 @@
 #include <dt-bindings/clock/rk3288-cru.h>
 #include <dt-bindings/power/rk3288-power.h>
 #include <dt-bindings/thermal/thermal.h>
-#include <dt-bindings/power/rk3288-power.h>
 #include <dt-bindings/soc/rockchip,boot-mode.h>
 
 / {
@@ -20,6 +19,15 @@
 
 	aliases {
 		ethernet0 = &gmac;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+		gpio5 = &gpio5;
+		gpio6 = &gpio6;
+		gpio7 = &gpio7;
+		gpio8 = &gpio8;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c2 = &i2c2;
@@ -101,7 +109,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -155,47 +163,6 @@
 		};
 	};
 
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		dmac_peri: dma-controller@ff250000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x0 0xff250000 0x0 0x4000>;
-			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMAC2>;
-			clock-names = "apb_pclk";
-		};
-
-		dmac_bus_ns: dma-controller@ff600000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x0 0xff600000 0x0 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMAC1>;
-			clock-names = "apb_pclk";
-			status = "disabled";
-		};
-
-		dmac_bus_s: dma-controller@ffb20000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x0 0xffb20000 0x0 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMAC1>;
-			clock-names = "apb_pclk";
-		};
-	};
-
 	reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -238,8 +205,8 @@
 		compatible = "rockchip,rk3288-timer";
 		reg = <0x0 0xff810000 0x0 0x20>;
 		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};
 
 	display-subsystem {
@@ -247,7 +214,7 @@
 		ports = <&vopl_out>, <&vopb_out>;
 	};
 
-	sdmmc: dwmmc@ff0c0000 {
+	sdmmc: mmc@ff0c0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		max-frequency = <150000000>;
 		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
@@ -261,7 +228,7 @@
 		status = "disabled";
 	};
 
-	sdio0: dwmmc@ff0d0000 {
+	sdio0: mmc@ff0d0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		max-frequency = <150000000>;
 		clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>,
@@ -275,7 +242,7 @@
 		status = "disabled";
 	};
 
-	sdio1: dwmmc@ff0e0000 {
+	sdio1: mmc@ff0e0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		max-frequency = <150000000>;
 		clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>,
@@ -289,7 +256,7 @@
 		status = "disabled";
 	};
 
-	emmc: dwmmc@ff0f0000 {
+	emmc: mmc@ff0f0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		max-frequency = <150000000>;
 		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
@@ -420,6 +387,8 @@
 		reg-io-width = <4>;
 		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
 		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac_peri 1>, <&dmac_peri 2>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart0_xfer>;
 		status = "disabled";
@@ -433,6 +402,8 @@
 		reg-io-width = <4>;
 		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
 		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac_peri 3>, <&dmac_peri 4>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart1_xfer>;
 		status = "disabled";
@@ -459,6 +430,8 @@
 		reg-io-width = <4>;
 		clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
 		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac_peri 7>, <&dmac_peri 8>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart3_xfer>;
 		status = "disabled";
@@ -472,20 +445,34 @@
 		reg-io-width = <4>;
 		clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
 		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac_peri 9>, <&dmac_peri 10>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart4_xfer>;
 		status = "disabled";
 	};
 
+	dmac_peri: dma-controller@ff250000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x0 0xff250000 0x0 0x4000>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC2>;
+		clock-names = "apb_pclk";
+	};
+
 	thermal-zones {
-		reserve_thermal: reserve_thermal {
+		reserve_thermal: reserve-thermal {
 			polling-delay-passive = <1000>; /* milliseconds */
 			polling-delay = <5000>; /* milliseconds */
 
 			thermal-sensors = <&tsadc 0>;
 		};
 
-		cpu_thermal: cpu_thermal {
+		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <100>; /* milliseconds */
 			polling-delay = <5000>; /* milliseconds */
 
@@ -529,7 +516,7 @@
 			};
 		};
 
-		gpu_thermal: gpu_thermal {
+		gpu_thermal: gpu-thermal {
 			polling-delay-passive = <100>; /* milliseconds */
 			polling-delay = <5000>; /* milliseconds */
 
@@ -567,9 +554,9 @@
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
 		pinctrl-names = "init", "default", "sleep";
-		pinctrl-0 = <&otp_gpio>;
+		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
-		pinctrl-2 = <&otp_gpio>;
+		pinctrl-2 = <&otp_pin>;
 		#thermal-sensor-cells = <1>;
 		rockchip,grf = <&grf>;
 		rockchip,hw-tshut-temp = <95000>;
@@ -601,13 +588,21 @@
 		reg = <0x0 0xff500000 0x0 0x100>;
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_USBHOST0>;
-		clock-names = "usbhost";
 		phys = <&usbphy1>;
 		phy-names = "usb";
 		status = "disabled";
 	};
 
-	/* NOTE: ohci@ff520000 doesn't actually work on hardware */
+	/* NOTE: doesn't work on RK3288, but was fixed on RK3288W */
+	usb_host0_ohci: usb@ff520000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xff520000 0x0 0x100>;
+		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USBHOST0>;
+		phys = <&usbphy1>;
+		phy-names = "usb";
+		status = "disabled";
+	};
 
 	usb_host1: usb@ff540000 {
 		compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
@@ -644,7 +639,19 @@
 		reg = <0x0 0xff5c0000 0x0 0x100>;
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HSIC>;
-		clock-names = "usbhost";
+		status = "disabled";
+	};
+
+	dmac_bus_ns: dma-controller@ff600000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x0 0xff600000 0x0 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC1>;
+		clock-names = "apb_pclk";
 		status = "disabled";
 	};
 
@@ -681,7 +688,6 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm0_pin>;
 		clocks = <&cru PCLK_RKPWM>;
-		clock-names = "pwm";
 		status = "disabled";
 	};
 
@@ -692,7 +698,6 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm1_pin>;
 		clocks = <&cru PCLK_RKPWM>;
-		clock-names = "pwm";
 		status = "disabled";
 	};
 
@@ -703,7 +708,6 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm2_pin>;
 		clocks = <&cru PCLK_RKPWM>;
-		clock-names = "pwm";
 		status = "disabled";
 	};
 
@@ -714,11 +718,10 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm3_pin>;
 		clocks = <&cru PCLK_RKPWM>;
-		clock-names = "pwm";
 		status = "disabled";
 	};
 
-	bus_intmem@ff700000 {
+	bus_intmem: sram@ff700000 {
 		compatible = "mmio-sram";
 		reg = <0x0 0xff700000 0x0 0x18000>;
 		#address-cells = <1>;
@@ -730,7 +733,7 @@
 		};
 	};
 
-	sram@ff720000 {
+	pmu_sram: sram@ff720000 {
 		compatible = "rockchip,rk3288-pmu-sram", "mmio-sram";
 		reg = <0x0 0xff720000 0x0 0x1000>;
 	};
@@ -771,7 +774,7 @@
 			 *	*_HDMI		HDMI
 			 *	*_MIPI_*	MIPI
 			 */
-			pd_vio@RK3288_PD_VIO {
+			power-domain@RK3288_PD_VIO {
 				reg = <RK3288_PD_VIO>;
 				clocks = <&cru ACLK_IEP>,
 					 <&cru ACLK_ISP>,
@@ -807,19 +810,21 @@
 					 <&qos_vio2_rga_r>,
 					 <&qos_vio2_rga_w>,
 					 <&qos_vio1_isp_r>;
+				#power-domain-cells = <0>;
 			};
 
 			/*
 			 * Note: The following 3 are HEVC(H.265) clocks,
 			 * and on the ACLK_HEVC_NIU (NOC).
 			 */
-			pd_hevc@RK3288_PD_HEVC {
+			power-domain@RK3288_PD_HEVC {
 				reg = <RK3288_PD_HEVC>;
 				clocks = <&cru ACLK_HEVC>,
 					 <&cru SCLK_HEVC_CABAC>,
 					 <&cru SCLK_HEVC_CORE>;
 				pm_qos = <&qos_hevc_r>,
 					 <&qos_hevc_w>;
+				#power-domain-cells = <0>;
 			};
 
 			/*
@@ -827,22 +832,24 @@
 			 * (video endecoder & decoder) clocks that on the
 			 * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC).
 			 */
-			pd_video@RK3288_PD_VIDEO {
+			power-domain@RK3288_PD_VIDEO {
 				reg = <RK3288_PD_VIDEO>;
 				clocks = <&cru ACLK_VCODEC>,
 					 <&cru HCLK_VCODEC>;
 				pm_qos = <&qos_video>;
+				#power-domain-cells = <0>;
 			};
 
 			/*
 			 * Note: ACLK_GPU is the GPU clock,
 			 * and on the ACLK_GPU_NIU (NOC).
 			 */
-			pd_gpu@RK3288_PD_GPU {
+			power-domain@RK3288_PD_GPU {
 				reg = <RK3288_PD_GPU>;
 				clocks = <&cru ACLK_GPU>;
 				pm_qos = <&qos_gpu_r>,
 					 <&qos_gpu_w>;
+				#power-domain-cells = <0>;
 			};
 		};
 
@@ -864,6 +871,8 @@
 	cru: clock-controller@ff760000 {
 		compatible = "rockchip,rk3288-cru";
 		reg = <0x0 0xff760000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -942,12 +951,12 @@
 		status = "disabled";
 	};
 
-	spdif: sound@ff88b0000 {
+	spdif: sound@ff8b0000 {
 		compatible = "rockchip,rk3288-spdif", "rockchip,rk3066-spdif";
 		reg = <0x0 0xff8b0000 0x0 0x10000>;
 		#sound-dai-cells = <0>;
-		clock-names = "hclk", "mclk";
-		clocks = <&cru HCLK_SPDIF8CH>, <&cru SCLK_SPDIF8CH>;
+		clocks = <&cru SCLK_SPDIF8CH>, <&cru HCLK_SPDIF8CH>;
+		clock-names = "mclk", "hclk";
 		dmas = <&dmac_bus_s 3>;
 		dma-names = "tx";
 		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -962,12 +971,10 @@
 		reg = <0x0 0xff890000 0x0 0x10000>;
 		#sound-dai-cells = <0>;
 		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
+		clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0>;
+		clock-names = "i2s_clk", "i2s_hclk";
 		dmas = <&dmac_bus_s 0>, <&dmac_bus_s 1>;
 		dma-names = "tx", "rx";
-		clock-names = "i2s_hclk", "i2s_clk";
-		clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s0_bus>;
 		rockchip,playback-channels = <8>;
@@ -975,7 +982,7 @@
 		status = "disabled";
 	};
 
-	crypto: cypto-controller@ff8a0000 {
+	crypto: crypto@ff8a0000 {
 		compatible = "rockchip,rk3288-crypto";
 		reg = <0x0 0xff8a0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
@@ -984,14 +991,12 @@
 		clock-names = "aclk", "hclk", "sclk", "apb_pclk";
 		resets = <&cru SRST_CRYPTO>;
 		reset-names = "crypto-rst";
-		status = "okay";
 	};
 
 	iep_mmu: iommu@ff900800 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff900800 0x0 0x40>;
 		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1002,7 +1007,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff914000 0x0 0x100>, <0x0 0xff915000 0x0 0x100>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "isp_mmu";
 		clocks = <&cru ACLK_ISP>, <&cru HCLK_ISP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1063,7 +1067,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff930300 0x0 0x100>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vopb_mmu";
 		clocks = <&cru ACLK_VOP0>, <&cru HCLK_VOP0>;
 		clock-names = "aclk", "iface";
 		power-domains = <&power RK3288_PD_VIO>;
@@ -1113,7 +1116,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff940300 0x0 0x100>;
 		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vopl_mmu";
 		clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>;
 		clock-names = "aclk", "iface";
 		power-domains = <&power RK3288_PD_VIO>;
@@ -1121,7 +1123,7 @@
 		status = "disabled";
 	};
 
-	mipi_dsi: mipi@ff960000 {
+	mipi_dsi: dsi@ff960000 {
 		compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi";
 		reg = <0x0 0xff960000 0x0 0x4000>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
@@ -1132,18 +1134,28 @@
 		status = "disabled";
 
 		ports {
-			mipi_in: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mipi_in: port@0 {
+				reg = <0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+
 				mipi_in_vopb: endpoint@0 {
 					reg = <0>;
 					remote-endpoint = <&vopb_out_mipi>;
 				};
+
 				mipi_in_vopl: endpoint@1 {
 					reg = <1>;
 					remote-endpoint = <&vopl_out_mipi>;
 				};
 			};
+
+			mipi_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};
 
@@ -1164,7 +1176,6 @@
 
 			lvds_in: port@0 {
 				reg = <0>;
-
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -1172,11 +1183,16 @@
 					reg = <0>;
 					remote-endpoint = <&vopb_out_lvds>;
 				};
+
 				lvds_in_vopl: endpoint@1 {
 					reg = <1>;
 					remote-endpoint = <&vopl_out_lvds>;
 				};
 			};
+
+			lvds_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};
 
@@ -1188,6 +1204,7 @@
 		clock-names = "dp", "pclk";
 		phys = <&edp_phy>;
 		phy-names = "dp";
+		power-domains = <&power RK3288_PD_VIO>;
 		resets = <&cru SRST_EDP>;
 		reset-names = "dp";
 		rockchip,grf = <&grf>;
@@ -1196,19 +1213,26 @@
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
+
 			edp_in: port@0 {
 				reg = <0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+
 				edp_in_vopb: endpoint@0 {
 					reg = <0>;
 					remote-endpoint = <&vopb_out_edp>;
 				};
+
 				edp_in_vopl: endpoint@1 {
 					reg = <1>;
 					remote-endpoint = <&vopl_out_edp>;
 				};
 			};
+
+			edp_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};
 
@@ -1256,7 +1280,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff9a0800 0x0 0x100>;
 		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1267,7 +1290,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff9c0440 0x0 0x40>, <0x0 0xff9c0480 0x0 0x40>;
 		interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "hevc_mmu";
 		clocks = <&cru ACLK_HEVC>, <&cru HCLK_HEVC>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1288,7 +1310,7 @@
 		status = "disabled";
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-1 {
 		compatible = "operating-points-v2";
 
 		opp-100000000 {
@@ -1314,75 +1336,87 @@
 	};
 
 	qos_gpu_r: qos@ffaa0000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffaa0000 0x0 0x20>;
 	};
 
 	qos_gpu_w: qos@ffaa0080 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffaa0080 0x0 0x20>;
 	};
 
 	qos_vio1_vop: qos@ffad0000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0000 0x0 0x20>;
 	};
 
 	qos_vio1_isp_w0: qos@ffad0100 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0100 0x0 0x20>;
 	};
 
 	qos_vio1_isp_w1: qos@ffad0180 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0180 0x0 0x20>;
 	};
 
 	qos_vio0_vop: qos@ffad0400 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0400 0x0 0x20>;
 	};
 
 	qos_vio0_vip: qos@ffad0480 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0480 0x0 0x20>;
 	};
 
 	qos_vio0_iep: qos@ffad0500 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0500 0x0 0x20>;
 	};
 
 	qos_vio2_rga_r: qos@ffad0800 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0800 0x0 0x20>;
 	};
 
 	qos_vio2_rga_w: qos@ffad0880 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0880 0x0 0x20>;
 	};
 
 	qos_vio1_isp_r: qos@ffad0900 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffad0900 0x0 0x20>;
 	};
 
 	qos_video: qos@ffae0000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffae0000 0x0 0x20>;
 	};
 
 	qos_hevc_r: qos@ffaf0000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffaf0000 0x0 0x20>;
 	};
 
 	qos_hevc_w: qos@ffaf0080 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3288-qos", "syscon";
 		reg = <0x0 0xffaf0080 0x0 0x20>;
 	};
 
+	dmac_bus_s: dma-controller@ffb20000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x0 0xffb20000 0x0 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC1>;
+		clock-names = "apb_pclk";
+	};
+
 	efuse: efuse@ffb40000 {
 		compatible = "rockchip,rk3288-efuse";
 		reg = <0x0 0xffb40000 0x0 0x20>;
@@ -1420,7 +1454,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		gpio0: gpio0@ff750000 {
+		gpio0: gpio@ff750000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff750000 0x0 0x100>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
@@ -1433,7 +1467,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@ff780000 {
+		gpio1: gpio@ff780000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff780000 0x0 0x100>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -1446,7 +1480,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@ff790000 {
+		gpio2: gpio@ff790000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff790000 0x0 0x100>;
 			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
@@ -1459,7 +1493,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@ff7a0000 {
+		gpio3: gpio@ff7a0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7a0000 0x0 0x100>;
 			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
@@ -1472,7 +1506,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio4: gpio4@ff7b0000 {
+		gpio4: gpio@ff7b0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7b0000 0x0 0x100>;
 			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
@@ -1485,7 +1519,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio5: gpio5@ff7c0000 {
+		gpio5: gpio@ff7c0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7c0000 0x0 0x100>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
@@ -1498,7 +1532,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio6: gpio6@ff7d0000 {
+		gpio6: gpio@ff7d0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7d0000 0x0 0x100>;
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
@@ -1511,7 +1545,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio7: gpio7@ff7e0000 {
+		gpio7: gpio@ff7e0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7e0000 0x0 0x100>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
@@ -1524,7 +1558,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio8: gpio8@ff7f0000 {
+		gpio8: gpio@ff7f0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7f0000 0x0 0x100>;
 			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
@@ -1578,7 +1612,7 @@
 			drive-strength = <12>;
 		};
 
-		sleep {
+		suspend {
 			global_pwroff: global-pwroff {
 				rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>;
 			};
@@ -1926,7 +1960,7 @@
 		};
 
 		tsadc {
-			otp_gpio: otp-gpio {
+			otp_pin: otp-pin {
 				rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 
diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
index 97307a405e60..f37137f298d5 100644
--- a/arch/arm/boot/dts/rk3xxx.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3xxx.dtsi
@@ -16,14 +16,15 @@
 
 	aliases {
 		ethernet0 = &emac;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c2 = &i2c2;
 		i2c3 = &i2c3;
 		i2c4 = &i2c4;
-		mshc0 = &emmc;
-		mshc1 = &mmc0;
-		mshc2 = &mmc1;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
@@ -32,47 +33,6 @@
 		spi1 = &spi1;
 	};
 
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		dmac1_s: dma-controller@20018000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x20018000 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMA1>;
-			clock-names = "apb_pclk";
-		};
-
-		dmac1_ns: dma-controller@2001c000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x2001c000 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMA1>;
-			clock-names = "apb_pclk";
-			status = "disabled";
-		};
-
-		dmac2: dma-controller@20078000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x20078000 0x4000>;
-			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMA2>;
-			clock-names = "apb_pclk";
-		};
-	};
-
 	xin24m: oscillator {
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
@@ -84,14 +44,26 @@
 		compatible = "arm,mali-400";
 		reg = <0x10090000 0x10000>;
 		clocks = <&cru ACLK_GPU>, <&cru ACLK_GPU>;
-		clock-names = "core", "bus";
+		clock-names = "bus", "core";
 		assigned-clocks = <&cru ACLK_GPU>;
 		assigned-clock-rates = <100000000>;
 		resets = <&cru SRST_GPU>;
 		status = "disabled";
 	};
 
-	L2: l2-cache-controller@10138000 {
+	vpu: video-codec@10104000 {
+		compatible = "rockchip,rk3066-vpu";
+		reg = <0x10104000 0x800>;
+		interrupts = <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "vepu", "vdpu";
+		clocks = <&cru ACLK_VDPU>, <&cru HCLK_VDPU>,
+			 <&cru ACLK_VEPU>, <&cru HCLK_VEPU>;
+		clock-names = "aclk_vdpu", "hclk_vdpu",
+			      "aclk_vepu", "hclk_vepu";
+	};
+
+	L2: cache-controller@10138000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x10138000 0x1000>;
 		cache-unified;
@@ -108,6 +80,13 @@
 		reg = <0x1013c200 0x20>;
 		interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
 		clocks = <&cru CORE_PERI>;
+		status = "disabled";
+		/* The clock source and the sched_clock provided by the arm_global_timer
+		 * on Rockchip rk3066a/rk3188 are quite unstable because their rates
+		 * depend on the CPU frequency.
+		 * Keep the arm_global_timer disabled in order to have the
+		 * DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
+		 */
 	};
 
 	local_timer: local-timer@1013c600 {
@@ -148,42 +127,42 @@
 	};
 
 	qos_gpu: qos@1012d000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012d000 0x20>;
 	};
 
 	qos_vpu: qos@1012e000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012e000 0x20>;
 	};
 
 	qos_lcdc0: qos@1012f000 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012f000 0x20>;
 	};
 
 	qos_cif0: qos@1012f080 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012f080 0x20>;
 	};
 
 	qos_ipp: qos@1012f100 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012f100 0x20>;
 	};
 
 	qos_lcdc1: qos@1012f180 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012f180 0x20>;
 	};
 
 	qos_cif1: qos@1012f200 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012f200 0x20>;
 	};
 
 	qos_rga: qos@1012f280 {
-		compatible = "syscon";
+		compatible = "rockchip,rk3066-qos", "syscon";
 		reg = <0x1012f280 0x20>;
 	};
 
@@ -218,8 +197,6 @@
 		compatible = "snps,arc-emac";
 		reg = <0x10204000 0x3c>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		rockchip,grf = <&grf>;
 
@@ -231,7 +208,7 @@
 		status = "disabled";
 	};
 
-	mmc0: dwmmc@10214000 {
+	mmc0: mmc@10214000 {
 		compatible = "rockchip,rk2928-dw-mshc";
 		reg = <0x10214000 0x1000>;
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -245,7 +222,7 @@
 		status = "disabled";
 	};
 
-	mmc1: dwmmc@10218000 {
+	mmc1: mmc@10218000 {
 		compatible = "rockchip,rk2928-dw-mshc";
 		reg = <0x10218000 0x1000>;
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
@@ -259,7 +236,7 @@
 		status = "disabled";
 	};
 
-	emmc: dwmmc@1021c000 {
+	emmc: mmc@1021c000 {
 		compatible = "rockchip,rk2928-dw-mshc";
 		reg = <0x1021c000 0x1000>;
 		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
@@ -273,6 +250,15 @@
 		status = "disabled";
 	};
 
+	nfc: nand-controller@10500000 {
+		compatible = "rockchip,rk2928-nfc";
+		reg = <0x10500000 0x4000>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_NANDC0>;
+		clock-names = "ahb";
+		status = "disabled";
+	};
+
 	pmu: pmu@20004000 {
 		compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd";
 		reg = <0x20004000 0x100>;
@@ -288,10 +274,35 @@
 	};
 
 	grf: grf@20008000 {
-		compatible = "syscon";
+		compatible = "syscon", "simple-mfd";
 		reg = <0x20008000 0x200>;
 	};
 
+	dmac1_s: dma-controller@20018000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x20018000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMA1>;
+		clock-names = "apb_pclk";
+	};
+
+	dmac1_ns: dma-controller@2001c000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x2001c000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMA1>;
+		clock-names = "apb_pclk";
+		status = "disabled";
+	};
+
 	i2c0: i2c@2002d000 {
 		compatible = "rockchip,rk3066-i2c";
 		reg = <0x2002d000 0x1000>;
@@ -466,4 +477,16 @@
 		dma-names = "tx", "rx";
 		status = "disabled";
 	};
+
+	dmac2: dma-controller@20078000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x20078000 0x4000>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMA2>;
+		clock-names = "apb_pclk";
+	};
 };
diff --git a/arch/arm/boot/dts/rockchip/rockchip-radxa-dalang-carrier.dtsi b/arch/arm/boot/dts/rockchip/rockchip-radxa-dalang-carrier.dtsi
new file mode 100644
index 000000000000..da1d548b7330
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rockchip-radxa-dalang-carrier.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2019 Radxa Limited
+ * Copyright (c) 2019 Amarula Solutions(India)
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&hym8563>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+	};
+
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vbus_host: vbus-host {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb1_en_oc>;
+		regulator-name = "vbus_host"; /* HOST-5V */
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vbus_typec: vbus-typec {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_en_oc>;
+		regulator-name = "vbus_typec";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&gmac {
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&sdio0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	vqmmc-supply = <&vccio_sd>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rv1108-elgin-r1.dts b/arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dts
index b1db924710c8..2d9994379eb2 100644
--- a/arch/arm/boot/dts/rv1108-elgin-r1.dts
+++ b/arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dts
@@ -12,6 +12,10 @@
 	model = "Elgin RV1108 R1 board";
 	compatible = "elgin,rv1108-r1", "rockchip,rv1108";
 
+	aliases {
+		mmc0 = &emmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x08000000>;
@@ -68,6 +72,7 @@
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
 		rockchip,system-power-controller;
+		#clock-cells = <0>;
 
 		vcc1-supply = <&vcc_sys>;
 		vcc2-supply = <&vcc_sys>;
@@ -78,7 +83,7 @@
 
 		regulators {
 			vdd_core: DCDC_REG1 {
-				regulator-name= "vdd_core";
+				regulator-name = "vdd_core";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
@@ -90,7 +95,7 @@
 			};
 
 			vdd_buck2: DCDC_REG2 {
-				regulator-name= "vdd_buck2";
+				regulator-name = "vdd_buck2";
 				regulator-min-microvolt = <2200000>;
 				regulator-max-microvolt = <2200000>;
 				regulator-always-on;
@@ -101,7 +106,7 @@
 			};
 
 			vcc_ddr: DCDC_REG3 {
-				regulator-name= "vcc_ddr";
+				regulator-name = "vcc_ddr";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-state-mem {
@@ -110,7 +115,7 @@
 			};
 
 			vcc_io: DCDC_REG4 {
-				regulator-name= "vcc_io";
+				regulator-name = "vcc_io";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
@@ -122,7 +127,7 @@
 			};
 
 			vdd_10: LDO_REG1 {
-				regulator-name= "vdd_10";
+				regulator-name = "vdd_10";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
@@ -133,7 +138,7 @@
 			};
 
 			vcc_18: LDO_REG2 {
-				regulator-name= "vcc_18";
+				regulator-name = "vcc_18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
@@ -144,7 +149,7 @@
 			};
 
 			vdd10_pmu: LDO_REG3 {
-				regulator-name= "vdd10_pmu";
+				regulator-name = "vdd10_pmu";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
diff --git a/arch/arm/boot/dts/rv1108-evb.dts b/arch/arm/boot/dts/rockchip/rv1108-evb.dts
index 30f3d0470ad9..ef150f4ee99d 100644
--- a/arch/arm/boot/dts/rv1108-evb.dts
+++ b/arch/arm/boot/dts/rockchip/rv1108-evb.dts
@@ -8,6 +8,10 @@
 	model = "Rockchip RV1108 Evaluation board";
 	compatible = "rockchip,rv1108-evb", "rockchip,rv1108";
 
+	aliases {
+		mmc0 = &sdmmc;
+	};
+
 	memory@60000000 {
 		device_type = "memory";
 		reg = <0x60000000 0x08000000>;
@@ -81,6 +85,7 @@
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
 		rockchip,system-power-controller;
+		#clock-cells = <0>;
 
 		vcc1-supply = <&vcc_sys>;
 		vcc2-supply = <&vcc_sys>;
@@ -91,7 +96,7 @@
 
 		regulators {
 			vdd_core: DCDC_REG1 {
-				regulator-name= "vdd_core";
+				regulator-name = "vdd_core";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
@@ -103,7 +108,7 @@
 			};
 
 			vdd_cam: DCDC_REG2 {
-				regulator-name= "vdd_cam";
+				regulator-name = "vdd_cam";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <2000000>;
 				regulator-state-mem {
@@ -112,7 +117,7 @@
 			};
 
 			vcc_ddr: DCDC_REG3 {
-				regulator-name= "vcc_ddr";
+				regulator-name = "vcc_ddr";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-state-mem {
@@ -121,7 +126,7 @@
 			};
 
 			vcc_io: DCDC_REG4 {
-				regulator-name= "vcc_io";
+				regulator-name = "vcc_io";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
@@ -133,7 +138,7 @@
 			};
 
 			vdd_10: LDO_REG1 {
-				regulator-name= "vdd_10";
+				regulator-name = "vdd_10";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
@@ -144,7 +149,7 @@
 			};
 
 			vcc_18: LDO_REG2 {
-				regulator-name= "vcc_18";
+				regulator-name = "vcc_18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
@@ -155,7 +160,7 @@
 			};
 
 			vdd10_pmu: LDO_REG3 {
-				regulator-name= "vdd10_pmu";
+				regulator-name = "vdd10_pmu";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
diff --git a/arch/arm/boot/dts/rv1108.dtsi b/arch/arm/boot/dts/rockchip/rv1108.dtsi
index 5876690ee09e..abf3006f0a84 100644
--- a/arch/arm/boot/dts/rv1108.dtsi
+++ b/arch/arm/boot/dts/rockchip/rv1108.dtsi
@@ -40,7 +40,7 @@
 		};
 	};
 
-	cpu_opp_table: opp_table {
+	cpu_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 
 		opp-408000000 {
@@ -85,24 +85,7 @@
 		#clock-cells = <0>;
 	};
 
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		pdma: pdma@102a0000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x102a0000 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			clocks = <&cru ACLK_DMAC>;
-			clock-names = "apb_pclk";
-		};
-	};
-
-	bus_intmem@10080000 {
+	bus_intmem: sram@10080000 {
 		compatible = "mmio-sram";
 		reg = <0x10080000 0x2000>;
 		#address-cells = <1>;
@@ -120,7 +103,6 @@
 		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
 		clock-names = "baudclk", "apb_pclk";
 		dmas = <&pdma 6>, <&pdma 7>;
-		#dma-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart2m0_xfer>;
 		status = "disabled";
@@ -136,7 +118,6 @@
 		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
 		clock-names = "baudclk", "apb_pclk";
 		dmas = <&pdma 4>, <&pdma 5>;
-		#dma-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart1_xfer>;
 		status = "disabled";
@@ -152,7 +133,6 @@
 		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
 		clock-names = "baudclk", "apb_pclk";
 		dmas = <&pdma 2>, <&pdma 3>;
-		#dma-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
 		status = "disabled";
@@ -208,7 +188,6 @@
 		clock-names = "spiclk", "apb_pclk";
 		dmas = <&pdma 8>, <&pdma 9>;
 		dma-names = "tx", "rx";
-		#dma-cells = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		status = "disabled";
@@ -262,13 +241,29 @@
 		status = "disabled";
 	};
 
+	pdma: dma-controller@102a0000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x102a0000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC>;
+		clock-names = "apb_pclk";
+	};
+
 	grf: syscon@10300000 {
 		compatible = "rockchip,rv1108-grf", "syscon", "simple-mfd";
 		reg = <0x10300000 0x1000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		u2phy: usb2-phy@100 {
+		io_domains: io-domains {
+			compatible = "rockchip,rv1108-io-voltage-domain";
+			status = "disabled";
+		};
+
+		u2phy: usb2phy@100 {
 			compatible = "rockchip,rv1108-usb2phy";
 			reg = <0x100 0x0c>;
 			clocks = <&cru SCLK_USBPHY>;
@@ -298,16 +293,15 @@
 		compatible = "rockchip,rv1108-timer", "rockchip,rk3288-timer";
 		reg = <0x10350000 0x20>;
 		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};
 
-	watchdog: wdt@10360000 {
-		compatible = "snps,dw-wdt";
+	watchdog: watchdog@10360000 {
+		compatible = "rockchip,rv1108-wdt", "snps,dw-wdt";
 		reg = <0x10360000 0x100>;
 		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru PCLK_WDT>;
-		clock-names = "pclk_wdt";
 		status = "disabled";
 	};
 
@@ -355,9 +349,9 @@
 		clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
 		clock-names = "tsadc", "apb_pclk";
 		pinctrl-names = "init", "default", "sleep";
-		pinctrl-0 = <&otp_gpio>;
+		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
-		pinctrl-2 = <&otp_gpio>;
+		pinctrl-2 = <&otp_pin>;
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
 		rockchip,hw-tshut-temp = <120000>;
@@ -370,7 +364,6 @@
 		reg = <0x1038c000 0x100>;
 		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 		#io-channel-cells = <1>;
-		clock-frequency = <1000000>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
 		status = "disabled";
@@ -439,8 +432,13 @@
 	};
 
 	pmugrf: syscon@20060000 {
-		compatible = "rockchip,rv1108-pmugrf", "syscon";
+		compatible = "rockchip,rv1108-pmugrf", "syscon", "simple-mfd";
 		reg = <0x20060000 0x1000>;
+
+		pmu_io_domains: io-domains {
+			compatible = "rockchip,rv1108-pmu-io-voltage-domain";
+			status = "disabled";
+		};
 	};
 
 	usbgrf: syscon@202a0000 {
@@ -451,12 +449,25 @@
 	cru: clock-controller@20200000 {
 		compatible = "rockchip,rv1108-cru";
 		reg = <0x20200000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 	};
 
-	emmc: dwmmc@30110000 {
+	nfc: nand-controller@30100000 {
+		compatible = "rockchip,rv1108-nfc";
+		reg = <0x30100000  0x1000>;
+		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>;
+		clock-names = "ahb", "nfc";
+		assigned-clocks = <&cru SCLK_NANDC>;
+		assigned-clock-rates = <150000000>;
+		status = "disabled";
+	};
+
+	emmc: mmc@30110000 {
 		compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x30110000 0x4000>;
 		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
@@ -468,7 +479,7 @@
 		status = "disabled";
 	};
 
-	sdio: dwmmc@30120000 {
+	sdio: mmc@30120000 {
 		compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x30120000 0x4000>;
 		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
@@ -480,7 +491,7 @@
 		status = "disabled";
 	};
 
-	sdmmc: dwmmc@30130000 {
+	sdmmc: mmc@30130000 {
 		compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x30130000 0x4000>;
 		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
@@ -499,7 +510,6 @@
 		reg = <0x30140000 0x20000>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST0>, <&u2phy>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -510,7 +520,6 @@
 		reg = <0x30160000 0x20000>;
 		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_HOST0>, <&u2phy>;
-		clock-names = "usbhost", "utmi";
 		phys = <&u2phy_host>;
 		phy-names = "usb";
 		status = "disabled";
@@ -527,13 +536,23 @@
 		g-np-tx-fifo-size = <16>;
 		g-rx-fifo-size = <280>;
 		g-tx-fifo-size = <256 128 128 64 32 16>;
-		g-use-dma;
 		phys = <&u2phy_otg>;
 		phy-names = "usb2-phy";
 		status = "disabled";
 	};
 
-	gmac: eth@30200000 {
+	sfc: spi@301c0000 {
+		compatible = "rockchip,sfc";
+		reg = <0x301c0000 0x4000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+		clock-names = "clk_sfc", "hclk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
+	gmac: ethernet@30200000 {
 		compatible = "rockchip,rv1108-gmac";
 		reg = <0x30200000 0x10000>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
@@ -576,7 +595,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@20030000 {
+		gpio0: gpio@20030000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20030000 0x100>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
@@ -589,7 +608,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@10310000 {
+		gpio1: gpio@10310000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x10310000 0x100>;
 			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
@@ -602,7 +621,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@10320000 {
+		gpio2: gpio@10320000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x10320000 0x100>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
@@ -615,7 +634,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@10330000 {
+		gpio3: gpio@10330000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x10330000 0x100>;
 			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
@@ -701,9 +720,35 @@
 			};
 		};
 
+		sfc {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<2 RK_PA0 3 &pcfg_pull_none>,
+					<2 RK_PA1 3 &pcfg_pull_none>,
+					<2 RK_PA2 3 &pcfg_pull_none>,
+					<2 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<2 RK_PA0 3 &pcfg_pull_none>,
+					<2 RK_PA1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<2 RK_PB4 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<2 RK_PB7 2 &pcfg_pull_none>;
+			};
+		};
+
 		gmac {
 			rmii_pins: rmii-pins {
-				rockchip,pins =	<1 RK_PC5 2 &pcfg_pull_none>,
+				rockchip,pins = <1 RK_PC5 2 &pcfg_pull_none>,
 						<1 RK_PC3 2 &pcfg_pull_none>,
 						<1 RK_PC4 2 &pcfg_pull_none>,
 						<1 RK_PB2 3 &pcfg_pull_none_drv_12ma>,
@@ -736,7 +781,7 @@
 						<0 RK_PC6 3 &pcfg_pull_none>;
 			};
 
-			i2c2m1_gpio: i2c2m1-gpio {
+			i2c2m1_pins: i2c2m1-pins {
 				rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,
 						<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
@@ -748,7 +793,7 @@
 						<1 RK_PD4 2 &pcfg_pull_none>;
 			};
 
-			i2c2m05v_gpio: i2c2m05v-gpio {
+			i2c2m05v_pins: i2c2m05v-pins {
 				rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
 						<1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
@@ -875,7 +920,7 @@
 				rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
 			};
 
-			otp_gpio: otp-gpio {
+			otp_pin: otp-pin {
 				rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 		};
@@ -894,7 +939,7 @@
 				rockchip,pins = <3 RK_PA3 1 &pcfg_pull_none>;
 			};
 
-			uart0_rts_gpio: uart0-rts-gpio {
+			uart0_rts_pin: uart0-rts-pin {
 				rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 		};
diff --git a/arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts b/arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts
new file mode 100644
index 000000000000..45dced8087a3
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rv1109.dtsi"
+#include "rv1126-sonoff-ihost.dtsi"
+
+/ {
+	model = "Sonoff iHost 2G";
+	compatible = "itead,sonoff-ihost", "rockchip,rv1109";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1109.dtsi b/arch/arm/boot/dts/rockchip/rv1109.dtsi
new file mode 100644
index 000000000000..9cbaa08ab1b8
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1109.dtsi
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+
+#include "rv1126.dtsi"
+
+/ {
+	compatible = "rockchip,rv1109";
+
+	cpus {
+		/delete-node/ cpu@f02;
+		/delete-node/ cpu@f03;
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-edgeble-neu2-io.dts b/arch/arm/boot/dts/rockchip/rv1126-edgeble-neu2-io.dts
new file mode 100644
index 000000000000..0c2396b8f8db
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-edgeble-neu2-io.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-edgeble-neu2.dtsi"
+
+/ {
+	model = "Edgeble Neu2 IO Board";
+	compatible = "edgeble,neural-compute-module-2-io",
+		     "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	v3v3_sys: v3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&gmac {
+	assigned-clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>,
+			  <&cru CLK_GMAC_ETHERNET_OUT>;
+	assigned-clock-parents = <&cru CLK_GMAC_SRC_M1>, <&cru RGMII_MODE_CLK>;
+	assigned-clock-rates = <125000000>, <0>, <25000000>;
+	clock_in_out = "input";
+	phy-handle = <&phy>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_miim &rgmiim1_bus2 &rgmiim1_bus4 &clk_out_ethernetm1_pins>;
+	tx_delay = <0x2a>;
+	rx_delay = <0x1a>;
+	status = "okay";
+};
+
+&mdio {
+	phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c916",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_rst>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	ethernet {
+		eth_phy_rst: eth-phy-rst {
+			rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&pwm11 {
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr104;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-edgeble-neu2.dtsi b/arch/arm/boot/dts/rockchip/rv1126-edgeble-neu2.dtsi
new file mode 100644
index 000000000000..7ea8d7d16f5f
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-edgeble-neu2.dtsi
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+	compatible = "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+	aliases {
+		mmc0 = &emmc;
+	};
+
+	vccio_flash: vccio-flash-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&flash_vol_sel>;
+		regulator-name = "vccio_flash";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	sdio_pwrseq: pwrseq-sdio {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk>;
+	rockchip,default-sample-phase = <90>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vccio_flash>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc_buck5>;
+		vcc6-supply = <&vcc_buck5>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+
+		regulators {
+			vdd_npu_vepu: DCDC_REG1 {
+				regulator-name = "vdd_npu_vepu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <725000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc3v3_sys: DCDC_REG4 {
+				regulator-name = "vcc3v3_sys";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_buck5: DCDC_REG5 {
+				regulator-name = "vcc_buck5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2200000>;
+				};
+			};
+
+			vcc_0v8: LDO_REG1 {
+				regulator-name = "vcc_0v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_pmu: LDO_REG2 {
+				regulator-name = "vcc1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd0v8_pmu: LDO_REG3 {
+				regulator-name = "vcc0v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <800000>;
+				};
+			};
+
+			vcc_1v8: LDO_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_dovdd: LDO_REG5 {
+				regulator-name = "vcc_dovdd";
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_dvdd: LDO_REG6 {
+				regulator-name = "vcc_dvdd";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_avdd: LDO_REG7 {
+				regulator-name = "vcc_avdd";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG8 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: LDO_REG9 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_5v0: SWITCH_REG1 {
+				regulator-name = "vcc_5v0";
+			};
+
+			vcc_3v3: SWITCH_REG2 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	bt {
+		bt_enable: bt-enable {
+			rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	flash {
+		flash_vol_sel: flash-vol-sel {
+			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	wifi {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio0-supply = <&vcc1v8_pmu>;
+	pmuio1-supply = <&vcc3v3_sys>;
+	vccio1-supply = <&vccio_flash>;
+	vccio2-supply = <&vccio_sd>;
+	vccio3-supply = <&vcc_1v8>;
+	vccio4-supply = <&vcc_dovdd>;
+	vccio5-supply = <&vcc_1v8>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_dovdd>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&fspi_pins>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	max-frequency = <100000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,qca9377-bt";
+		clocks = <&rk809 1>;
+		enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; /* BT_RST */
+		max-speed = <2000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_enable>;
+		vddxo-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
+	};
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-pinctrl.dtsi b/arch/arm/boot/dts/rockchip/rv1126-pinctrl.dtsi
new file mode 100644
index 000000000000..06b1d7f2d858
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-pinctrl.dtsi
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <arm64/rockchip/rockchip-pinconf.dtsi>
+
+/*
+ * This file is auto generated by pin2dts tool, please keep these code
+ * by adding changes at end of this file.
+ */
+&pinctrl {
+	clk_out_ethernet {
+		/omit-if-no-ref/
+		clk_out_ethernetm1_pins: clk-out-ethernetm1-pins {
+			rockchip,pins =
+				/* clk_out_ethernet_m1 */
+				<2 RK_PC5 2 &pcfg_pull_none>;
+		};
+	};
+	emmc {
+		/omit-if-no-ref/
+		emmc_rstnout: emmc-rstnout {
+			rockchip,pins =
+				/* emmc_rstn */
+				<1 RK_PA3 2 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		emmc_bus8: emmc-bus8 {
+			rockchip,pins =
+				/* emmc_d0 */
+				<0 RK_PC4 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d1 */
+				<0 RK_PC5 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d2 */
+				<0 RK_PC6 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d3 */
+				<0 RK_PC7 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d4 */
+				<0 RK_PD0 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d5 */
+				<0 RK_PD1 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d6 */
+				<0 RK_PD2 2 &pcfg_pull_up_drv_level_2>,
+				/* emmc_d7 */
+				<0 RK_PD3 2 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		emmc_clk: emmc-clk {
+			rockchip,pins =
+				/* emmc_clko */
+				<0 RK_PD7 2 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		emmc_cmd: emmc-cmd {
+			rockchip,pins =
+				/* emmc_cmd */
+				<0 RK_PD5 2 &pcfg_pull_up_drv_level_2>;
+		};
+	};
+	fspi {
+		/omit-if-no-ref/
+		fspi_pins: fspi-pins {
+			rockchip,pins =
+				/* fspi_clk */
+				<1 RK_PA3 3 &pcfg_pull_down>,
+				/* fspi_cs0n */
+				<0 RK_PD4 3 &pcfg_pull_up>,
+				/* fspi_d0 */
+				<1 RK_PA0 3 &pcfg_pull_up>,
+				/* fspi_d1 */
+				<1 RK_PA1 3 &pcfg_pull_up>,
+				/* fspi_d2 */
+				<0 RK_PD6 3 &pcfg_pull_up>,
+				/* fspi_d3 */
+				<1 RK_PA2 3 &pcfg_pull_up>;
+		};
+	};
+	i2c0 {
+		/omit-if-no-ref/
+		i2c0_xfer: i2c0-xfer {
+			rockchip,pins =
+				/* i2c0_scl */
+				<0 RK_PB4 1 &pcfg_pull_none_drv_level_0_smt>,
+				/* i2c0_sda */
+				<0 RK_PB5 1 &pcfg_pull_none_drv_level_0_smt>;
+		};
+	};
+	i2c2 {
+		/omit-if-no-ref/
+		i2c2_xfer: i2c2-xfer {
+			rockchip,pins =
+				/* i2c2_scl */
+				<0 RK_PC2 1 &pcfg_pull_none_drv_level_0_smt>,
+				/* i2c2_sda */
+				<0 RK_PC3 1 &pcfg_pull_none_drv_level_0_smt>;
+		};
+	};
+	pwm2 {
+		/omit-if-no-ref/
+		pwm2m0_pins: pwm2m0-pins {
+			rockchip,pins =
+				/* pwm2_pin_m0 */
+				<0 RK_PC0 3 &pcfg_pull_none>;
+		};
+	};
+	pwm11 {
+		/omit-if-no-ref/
+		pwm11m0_pins: pwm11m0-pins {
+			rockchip,pins =
+				/* pwm11_pin_m0 */
+				<3 RK_PA7 6 &pcfg_pull_none>;
+		};
+	};
+	rgmii {
+		/omit-if-no-ref/
+		rgmiim1_miim: rgmiim1-miim {
+			rockchip,pins =
+				/* rgmii_mdc_m1 */
+				<2 RK_PC2 2 &pcfg_pull_none>,
+				/* rgmii_mdio_m1 */
+				<2 RK_PC1 2 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		rgmiim1_rxer: rgmiim1-rxer {
+			rockchip,pins =
+				/* rgmii_rxer_m1 */
+				<2 RK_PC0 2 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		rgmiim1_bus2: rgmiim1-bus2 {
+			rockchip,pins =
+				/* rgmii_rxd0_m1 */
+				<2 RK_PB5 2 &pcfg_pull_none>,
+				/* rgmii_rxd1_m1 */
+				<2 RK_PB6 2 &pcfg_pull_none>,
+				/* rgmii_rxdv_m1 */
+				<2 RK_PB4 2 &pcfg_pull_none>,
+				/* rgmii_txd0_m1 */
+				<2 RK_PC3 2 &pcfg_pull_none_drv_level_3>,
+				/* rgmii_txd1_m1 */
+				<2 RK_PC4 2 &pcfg_pull_none_drv_level_3>,
+				/* rgmii_txen_m1 */
+				<2 RK_PC6 2 &pcfg_pull_none_drv_level_3>;
+		};
+		/omit-if-no-ref/
+		rgmiim1_bus4: rgmiim1-bus4 {
+			rockchip,pins =
+				/* rgmii_rxclk_m1 */
+				<2 RK_PD3 2 &pcfg_pull_none>,
+				/* rgmii_rxd2_m1 */
+				<2 RK_PC7 2 &pcfg_pull_none>,
+				/* rgmii_rxd3_m1 */
+				<2 RK_PD0 2 &pcfg_pull_none>,
+				/* rgmii_txclk_m1 */
+				<2 RK_PD2 2 &pcfg_pull_none_drv_level_3>,
+				/* rgmii_txd2_m1 */
+				<2 RK_PD1 2 &pcfg_pull_none_drv_level_3>,
+				/* rgmii_txd3_m1 */
+				<2 RK_PA4 2 &pcfg_pull_none_drv_level_3>;
+		};
+		/omit-if-no-ref/
+		rgmiim1_mclkinout: rgmiim1-mclkinout {
+			rockchip,pins =
+				/* rgmii_clk_m1 */
+				<2 RK_PB7 2 &pcfg_pull_none>;
+		};
+	};
+	sdmmc0 {
+		/omit-if-no-ref/
+		sdmmc0_bus4: sdmmc0-bus4 {
+			rockchip,pins =
+				/* sdmmc0_d0 */
+				<1 RK_PA4 1 &pcfg_pull_up_drv_level_2>,
+				/* sdmmc0_d1 */
+				<1 RK_PA5 1 &pcfg_pull_up_drv_level_2>,
+				/* sdmmc0_d2 */
+				<1 RK_PA6 1 &pcfg_pull_up_drv_level_2>,
+				/* sdmmc0_d3 */
+				<1 RK_PA7 1 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		sdmmc0_clk: sdmmc0-clk {
+			rockchip,pins =
+				/* sdmmc0_clk */
+				<1 RK_PB0 1 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		sdmmc0_cmd: sdmmc0-cmd {
+			rockchip,pins =
+				/* sdmmc0_cmd */
+				<1 RK_PB1 1 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		sdmmc0_det: sdmmc0-det {
+			rockchip,pins =
+				<0 RK_PA3 1 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		sdmmc0_pwr: sdmmc0-pwr {
+			rockchip,pins =
+				<0 RK_PC0 1 &pcfg_pull_none>;
+		};
+	};
+	sdmmc1 {
+		/omit-if-no-ref/
+		sdmmc1_bus4: sdmmc1-bus4 {
+			rockchip,pins =
+				/* sdmmc1_d0 */
+				<1 RK_PB4 1 &pcfg_pull_up_drv_level_2>,
+				/* sdmmc1_d1 */
+				<1 RK_PB5 1 &pcfg_pull_up_drv_level_2>,
+				/* sdmmc1_d2 */
+				<1 RK_PB6 1 &pcfg_pull_up_drv_level_2>,
+				/* sdmmc1_d3 */
+				<1 RK_PB7 1 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		sdmmc1_clk: sdmmc1-clk {
+			rockchip,pins =
+				/* sdmmc1_clk */
+				<1 RK_PB2 1 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		sdmmc1_cmd: sdmmc1-cmd {
+			rockchip,pins =
+				/* sdmmc1_cmd */
+				<1 RK_PB3 1 &pcfg_pull_up_drv_level_2>;
+		};
+		/omit-if-no-ref/
+		sdmmc1_det: sdmmc1-det {
+			rockchip,pins =
+				<1 RK_PD0 2 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		sdmmc1_pwr: sdmmc1-pwr {
+			rockchip,pins =
+				<1 RK_PD1 2 &pcfg_pull_none>;
+		};
+	};
+	uart0 {
+		/omit-if-no-ref/
+		uart0_xfer: uart0-xfer {
+			rockchip,pins =
+				/* uart0_rx */
+				<1 RK_PC2 1 &pcfg_pull_up>,
+				/* uart0_tx */
+				<1 RK_PC3 1 &pcfg_pull_up>;
+		};
+		/omit-if-no-ref/
+		uart0_ctsn: uart0-ctsn {
+			rockchip,pins =
+				<1 RK_PC1 1 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		uart0_rtsn: uart0-rtsn {
+			rockchip,pins =
+				<1 RK_PC0 1 &pcfg_pull_none>;
+		};
+		/omit-if-no-ref/
+		uart0_rtsn_gpio: uart0-rts-pin {
+			rockchip,pins =
+				<1 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+	uart1 {
+		/omit-if-no-ref/
+		uart1m0_xfer: uart1m0-xfer {
+			rockchip,pins =
+				/* uart1_rx_m0 */
+				<0 RK_PB7 2 &pcfg_pull_up>,
+				/* uart1_tx_m0 */
+				<0 RK_PB6 2 &pcfg_pull_up>;
+		};
+	};
+	uart2 {
+		/omit-if-no-ref/
+		uart2m1_xfer: uart2m1-xfer {
+			rockchip,pins =
+				/* uart2_rx_m1 */
+				<3 RK_PA3 1 &pcfg_pull_up>,
+				/* uart2_tx_m1 */
+				<3 RK_PA2 1 &pcfg_pull_up>;
+		};
+	};
+	uart3 {
+		/omit-if-no-ref/
+		uart3m0_xfer: uart3m0-xfer {
+			rockchip,pins =
+				/* uart3_rx_m0 */
+				<3 RK_PC7 4 &pcfg_pull_up>,
+				/* uart3_tx_m0 */
+				<3 RK_PC6 4 &pcfg_pull_up>;
+		};
+		/omit-if-no-ref/
+		uart3m2_xfer: uart3m2-xfer {
+			rockchip,pins =
+				/* uart3_rx_m2 */
+				<3 RK_PA1 4 &pcfg_pull_up>,
+				/* uart3_tx_m2 */
+				<3 RK_PA0 4 &pcfg_pull_up>;
+		};
+	};
+	uart4 {
+		/omit-if-no-ref/
+		uart4m0_xfer: uart4m0-xfer {
+			rockchip,pins =
+				/* uart4_rx_m0 */
+				<3 RK_PA5 4 &pcfg_pull_up>,
+				/* uart4_tx_m0 */
+				<3 RK_PA4 4 &pcfg_pull_up>;
+		};
+		/omit-if-no-ref/
+		uart4m2_xfer: uart4m2-xfer {
+			rockchip,pins =
+				/* uart4_rx_m2 */
+				<1 RK_PD4 3 &pcfg_pull_up>,
+				/* uart4_tx_m2 */
+				<1 RK_PD5 3 &pcfg_pull_up>;
+		};
+	};
+	uart5 {
+		/omit-if-no-ref/
+		uart5m0_xfer: uart5m0-xfer {
+			rockchip,pins =
+				/* uart5_rx_m0 */
+				<3 RK_PA7 4 &pcfg_pull_up>,
+				/* uart5_tx_m0 */
+				<3 RK_PA6 4 &pcfg_pull_up>;
+		};
+		/omit-if-no-ref/
+		uart5m2_xfer: uart5m2-xfer {
+			rockchip,pins =
+				/* uart5_rx_m2 */
+				<2 RK_PA1 3 &pcfg_pull_up>,
+				/* uart5_tx_m2 */
+				<2 RK_PA0 3 &pcfg_pull_up>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts
new file mode 100644
index 000000000000..77386a48d81e
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-sonoff-ihost.dtsi"
+
+/ {
+	model = "Sonoff iHost 4G";
+	compatible = "itead,sonoff-ihost", "rockchip,rv1126";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi
new file mode 100644
index 000000000000..32b329e87a0c
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi
@@ -0,0 +1,404 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+	aliases {
+		ethernet0 = &gmac;
+		mmc0 = &emmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	sdio_pwrseq: pwrseq-sdio {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
+	rockchip,default-sample-phase = <90>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc_buck5>;
+		vcc6-supply = <&vcc_buck5>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+
+		regulators {
+			vdd_npu_vepu: DCDC_REG1 {
+				regulator-name = "vdd_npu_vepu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <725000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc3v3_sys: DCDC_REG4 {
+				regulator-name = "vcc3v3_sys";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_buck5: DCDC_REG5 {
+				regulator-name = "vcc_buck5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2200000>;
+				};
+			};
+
+			vcc_0v8: LDO_REG1 {
+				regulator-name = "vcc_0v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_pmu: LDO_REG2 {
+				regulator-name = "vcc1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd0v8_pmu: LDO_REG3 {
+				regulator-name = "vcc0v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <800000>;
+				};
+			};
+
+			vcc_1v8: LDO_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_dovdd: LDO_REG5 {
+				regulator-name = "vcc_dovdd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_dvdd: LDO_REG6 {
+				regulator-name = "vcc_dvdd";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_avdd: LDO_REG7 {
+				regulator-name = "vcc_avdd";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG8 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: LDO_REG9 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_5v0: SWITCH_REG1 {
+				regulator-name = "vcc_5v0";
+			};
+
+			vcc_3v3: SWITCH_REG2 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+		clock-output-names = "xin32k";
+	};
+};
+
+&gmac {
+	assigned-clocks = <&cru CLK_GMAC_SRC_M1>, <&cru CLK_GMAC_SRC>,
+			  <&cru CLK_GMAC_TX_RX>;
+	assigned-clock-parents = <&cru CLK_GMAC_RGMII_M1>, <&cru CLK_GMAC_SRC_M1>,
+				 <&cru RMII_MODE_CLK>;
+	assigned-clock-rates = <0>, <50000000>;
+	clock_in_out = "output";
+	phy-handle = <&phy>;
+	phy-mode = "rmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_miim &rgmiim1_rxer &rgmiim1_bus2 &rgmiim1_mclkinout>;
+	status = "okay";
+};
+
+&mdio {
+	phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_rst>;
+		reset-active-low;
+		reset-assert-us = <50000>;
+		reset-deassert-us = <10000>;
+		reset-gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	ethernet {
+		eth_phy_rst: eth-phy-rst {
+			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+	bt {
+		bt_enable: bt-enable {
+			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_dev: bt-wake-dev {
+			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_host: bt-wake-host {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	wifi {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio0-supply = <&vcc1v8_pmu>;
+	pmuio1-supply = <&vcc3v3_sys>;
+	vccio1-supply = <&vcc_1v8>;
+	vccio2-supply = <&vccio_sd>;
+	vccio3-supply = <&vcc_1v8>;
+	vccio4-supply = <&vcc_dovdd>;
+	vccio5-supply = <&vcc_1v8>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_dovdd>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	max-frequency = <100000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr104;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>; /* BT_WAKE */
+		enable-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; /* BT_RST */
+		host-wake-gpios = <&gpio1 RK_PC5 GPIO_ACTIVE_HIGH>; /* BT_WAKE_HOST */
+		max-speed = <2000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_enable>, <&bt_wake_dev>, <&bt_wake_host>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3m2_xfer>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4m2_xfer>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126.dtsi b/arch/arm/boot/dts/rockchip/rv1126.dtsi
new file mode 100644
index 000000000000..bb603cae13df
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126.dtsi
@@ -0,0 +1,623 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+#include <dt-bindings/clock/rockchip,rv1126-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rockchip,rv1126-power.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	compatible = "rockchip,rv1126";
+
+	interrupt-parent = <&gic>;
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c2 = &i2c2;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+		serial5 = &uart5;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@f00 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf00>;
+			enable-method = "psci";
+			clocks = <&cru ARMCLK>;
+		};
+
+		cpu1: cpu@f01 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf01>;
+			enable-method = "psci";
+			clocks = <&cru ARMCLK>;
+		};
+
+		cpu2: cpu@f02 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf02>;
+			enable-method = "psci";
+			clocks = <&cru ARMCLK>;
+		};
+
+		cpu3: cpu@f03 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0xf03>;
+			enable-method = "psci";
+			clocks = <&cru ARMCLK>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		clock-frequency = <24000000>;
+	};
+
+	display_subsystem {
+		compatible = "rockchip,display-subsystem";
+		ports = <&vop_out>;
+	};
+
+	xin24m: oscillator {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xin24m";
+		#clock-cells = <0>;
+	};
+
+	grf: syscon@fe000000 {
+		compatible = "rockchip,rv1126-grf", "syscon", "simple-mfd";
+		reg = <0xfe000000 0x20000>;
+	};
+
+	pmugrf: syscon@fe020000 {
+		compatible = "rockchip,rv1126-pmugrf", "syscon", "simple-mfd";
+		reg = <0xfe020000 0x1000>;
+
+		pmu_io_domains: io-domains {
+			compatible = "rockchip,rv1126-pmu-io-voltage-domain";
+			status = "disabled";
+		};
+	};
+
+	qos_emmc: qos@fe860000 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe860000 0x20>;
+	};
+
+	qos_nandc: qos@fe860080 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe860080 0x20>;
+	};
+
+	qos_sfc: qos@fe860200 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe860200 0x20>;
+	};
+
+	qos_sdio: qos@fe86c000 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe86c000 0x20>;
+	};
+
+	qos_iep: qos@fe8a0000 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe8a0000 0x20>;
+	};
+
+	qos_rga_rd: qos@fe8a0080 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe8a0080 0x20>;
+	};
+
+	qos_rga_wr: qos@fe8a0100 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe8a0100 0x20>;
+	};
+
+	qos_vop: qos@fe8a0180 {
+		compatible = "rockchip,rv1126-qos", "syscon";
+		reg = <0xfe8a0180 0x20>;
+	};
+
+	gic: interrupt-controller@feff0000 {
+		compatible = "arm,gic-400";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+
+		reg = <0xfeff1000 0x1000>,
+		      <0xfeff2000 0x2000>,
+		      <0xfeff4000 0x2000>,
+		      <0xfeff6000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	pmu: power-management@ff3e0000 {
+		compatible = "rockchip,rv1126-pmu", "syscon", "simple-mfd";
+		reg = <0xff3e0000 0x1000>;
+
+		power: power-controller {
+			compatible = "rockchip,rv1126-power-controller";
+			#power-domain-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-domain@RV1126_PD_NVM {
+				reg = <RV1126_PD_NVM>;
+				clocks = <&cru HCLK_EMMC>,
+					 <&cru CLK_EMMC>,
+					 <&cru HCLK_NANDC>,
+					 <&cru CLK_NANDC>,
+					 <&cru HCLK_SFC>,
+					 <&cru HCLK_SFCXIP>,
+					 <&cru SCLK_SFC>;
+				pm_qos = <&qos_emmc>,
+					 <&qos_nandc>,
+					 <&qos_sfc>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RV1126_PD_SDIO {
+				reg = <RV1126_PD_SDIO>;
+				clocks = <&cru HCLK_SDIO>,
+					 <&cru CLK_SDIO>;
+				pm_qos = <&qos_sdio>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RV1126_PD_VO {
+				reg = <RV1126_PD_VO>;
+				clocks = <&cru ACLK_RGA>,
+					 <&cru HCLK_RGA>,
+					 <&cru CLK_RGA_CORE>,
+					 <&cru ACLK_VOP>,
+					 <&cru HCLK_VOP>,
+					 <&cru DCLK_VOP>,
+					 <&cru PCLK_DSIHOST>,
+					 <&cru ACLK_IEP>,
+					 <&cru HCLK_IEP>,
+					 <&cru CLK_IEP_CORE>;
+				pm_qos = <&qos_rga_rd>,
+					 <&qos_rga_wr>,
+					 <&qos_vop>,
+					 <&qos_iep>;
+				#power-domain-cells = <0>;
+			};
+		};
+	};
+
+	i2c0: i2c@ff3f0000 {
+		compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c";
+		reg = <0xff3f0000 0x1000>;
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+		rockchip,grf = <&pmugrf>;
+		clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
+		clock-names = "i2c", "pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_xfer>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@ff400000 {
+		compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c";
+		reg = <0xff400000 0x1000>;
+		interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+		rockchip,grf = <&pmugrf>;
+		clocks = <&pmucru CLK_I2C2>, <&pmucru PCLK_I2C2>;
+		clock-names = "i2c", "pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_xfer>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	uart1: serial@ff410000 {
+		compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+		reg = <0xff410000 0x100>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&pmucru SCLK_UART1>, <&pmucru PCLK_UART1>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac 7>, <&dmac 6>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1m0_xfer>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	pwm2: pwm@ff430020 {
+		compatible = "rockchip,rv1126-pwm", "rockchip,rk3328-pwm";
+		reg = <0xff430020 0x10>;
+		clock-names = "pwm", "pclk";
+		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm2m0_pins>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pmucru: clock-controller@ff480000 {
+		compatible = "rockchip,rv1126-pmucru";
+		reg = <0xff480000 0x1000>;
+		rockchip,grf = <&grf>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+	cru: clock-controller@ff490000 {
+		compatible = "rockchip,rv1126-cru";
+		reg = <0xff490000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
+		rockchip,grf = <&grf>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+	dmac: dma-controller@ff4e0000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0xff4e0000 0x4000>;
+		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC>;
+		clock-names = "apb_pclk";
+	};
+
+	pwm11: pwm@ff550030 {
+		compatible = "rockchip,rv1126-pwm", "rockchip,rk3328-pwm";
+		reg = <0xff550030 0x10>;
+		clock-names = "pwm", "pclk";
+		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
+		pinctrl-0 = <&pwm11m0_pins>;
+		pinctrl-names = "default";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	uart0: serial@ff560000 {
+		compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+		reg = <0xff560000 0x100>;
+		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac 5>, <&dmac 4>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_xfer>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uart2: serial@ff570000 {
+		compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+		reg = <0xff570000 0x100>;
+		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac 9>, <&dmac 8>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2m1_xfer>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uart3: serial@ff580000 {
+		compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+		reg = <0xff580000 0x100>;
+		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac 11>, <&dmac 10>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart3m0_xfer>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uart4: serial@ff590000 {
+		compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+		reg = <0xff590000 0x100>;
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac 13>, <&dmac 12>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart4m0_xfer>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	uart5: serial@ff5a0000 {
+		compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+		reg = <0xff5a0000 0x100>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <24000000>;
+		clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac 15>, <&dmac 14>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart5m0_xfer>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	saradc: adc@ff5e0000 {
+		compatible = "rockchip,rv1126-saradc", "rockchip,rk3399-saradc";
+		reg = <0xff5e0000 0x100>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		#io-channel-cells = <1>;
+		clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
+		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC_P>;
+		reset-names = "saradc-apb";
+		status = "disabled";
+	};
+
+	timer0: timer@ff660000 {
+		compatible = "rockchip,rv1126-timer", "rockchip,rk3288-timer";
+		reg = <0xff660000 0x20>;
+		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_TIMER>, <&cru CLK_TIMER0>;
+		clock-names = "pclk", "timer";
+	};
+
+	vop: vop@ffb00000 {
+		compatible = "rockchip,rv1126-vop";
+		reg = <0xffb00000 0x200>, <0xffb00a00 0x400>;
+		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "aclk_vop", "dclk_vop", "hclk_vop";
+		clocks = <&cru ACLK_VOP>, <&cru DCLK_VOP>, <&cru HCLK_VOP>;
+		reset-names = "axi", "ahb", "dclk";
+		resets = <&cru SRST_VOP_A>, <&cru SRST_VOP_H>, <&cru SRST_VOP_D>;
+		iommus = <&vop_mmu>;
+		power-domains = <&power RV1126_PD_VO>;
+		status = "disabled";
+
+		vop_out: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vop_out_rgb: endpoint@0 {
+				reg = <0>;
+			};
+
+			vop_out_dsi: endpoint@1 {
+				reg = <1>;
+			};
+		};
+	};
+
+	vop_mmu: iommu@ffb00f00 {
+		compatible = "rockchip,iommu";
+		reg = <0xffb00f00 0x100>;
+		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "aclk", "iface";
+		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
+		#iommu-cells = <0>;
+		power-domains = <&power RV1126_PD_VO>;
+		status = "disabled";
+	};
+
+	gmac: ethernet@ffc40000 {
+		compatible = "rockchip,rv1126-gmac", "snps,dwmac-4.20a";
+		reg = <0xffc40000 0x4000>;
+		interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq", "eth_wake_irq";
+		rockchip,grf = <&grf>;
+		clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>,
+			 <&cru CLK_GMAC_TX_RX>, <&cru CLK_GMAC_REF>,
+			 <&cru ACLK_GMAC>, <&cru PCLK_GMAC>,
+			 <&cru CLK_GMAC_TX_RX>, <&cru CLK_GMAC_PTPREF>;
+		clock-names = "stmmaceth", "mac_clk_rx",
+			      "mac_clk_tx", "clk_mac_ref",
+			      "aclk_mac", "pclk_mac",
+			      "clk_mac_speed", "ptp_ref";
+		resets = <&cru SRST_GMAC_A>;
+		reset-names = "stmmaceth";
+
+		snps,mixed-burst;
+		snps,tso;
+
+		snps,axi-config = <&stmmac_axi_setup>;
+		snps,mtl-rx-config = <&mtl_rx_setup>;
+		snps,mtl-tx-config = <&mtl_tx_setup>;
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+		};
+
+		stmmac_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <4>;
+			snps,rd_osr_lmt = <8>;
+			snps,blen = <0 0 0 0 16 8 4>;
+		};
+
+		mtl_rx_setup: rx-queues-config {
+			snps,rx-queues-to-use = <1>;
+			queue0 {};
+		};
+
+		mtl_tx_setup: tx-queues-config {
+			snps,tx-queues-to-use = <1>;
+			queue0 {};
+		};
+	};
+
+	emmc: mmc@ffc50000 {
+		compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0xffc50000 0x4000>;
+		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_EMMC>, <&cru CLK_EMMC>,
+			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		max-frequency = <200000000>;
+		power-domains = <&power RV1126_PD_NVM>;
+		status = "disabled";
+	};
+
+	sdmmc: mmc@ffc60000 {
+		compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0xffc60000 0x4000>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDMMC>, <&cru CLK_SDMMC>,
+			 <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		max-frequency = <200000000>;
+		status = "disabled";
+	};
+
+	sdio: mmc@ffc70000 {
+		compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0xffc70000 0x4000>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDIO>, <&cru CLK_SDIO>,
+			 <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		max-frequency = <200000000>;
+		power-domains = <&power RV1126_PD_SDIO>;
+		status = "disabled";
+	};
+
+	sfc: spi@ffc90000  {
+		compatible = "rockchip,sfc";
+		reg = <0xffc90000 0x4000>;
+		interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+		assigned-clocks = <&cru SCLK_SFC>;
+		assigned-clock-rates = <80000000>;
+		clock-names = "clk_sfc", "hclk_sfc";
+		clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+		power-domains = <&power RV1126_PD_NVM>;
+		status = "disabled";
+	};
+
+	pinctrl: pinctrl {
+		compatible = "rockchip,rv1126-pinctrl";
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmugrf>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio@ff460000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0xff460000 0x100>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@ff620000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0xff620000 0x100>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@ff630000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0xff630000 0x100>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@ff640000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0xff640000 0x100>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio@ff650000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0xff650000 0x100>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
+
+#include "rv1126-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/s3c2416-pinctrl.dtsi b/arch/arm/boot/dts/s3c2416-pinctrl.dtsi
deleted file mode 100644
index 92439ee5d7de..000000000000
--- a/arch/arm/boot/dts/s3c2416-pinctrl.dtsi
+++ /dev/null
@@ -1,172 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Samsung S3C2416 pinctrl settings
- *
- * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
- */
-
-#include <dt-bindings/pinctrl/samsung.h>
-
-&pinctrl_0 {
-	/*
-	 * Pin banks
-	 */
-
-	gpa: gpa {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpb: gpb {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpc: gpc {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpd: gpd {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpe: gpe {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpf: gpf {
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpg: gpg {
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gph: gph {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpj: gpj {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpk: gpk {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpl: gpl {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpm: gpm {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	/*
-	 * Pin groups
-	 */
-
-	uart0_data: uart0-data {
-		samsung,pins = "gph-0", "gph-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	uart0_fctl: uart0-fctl {
-		samsung,pins = "gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	uart1_data: uart1-data {
-		samsung,pins = "gph-2", "gph-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	uart1_fctl: uart1-fctl {
-		samsung,pins = "gph-10", "gph-11";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	uart2_data: uart2-data {
-		samsung,pins = "gph-4", "gph-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	uart2_fctl: uart2-fctl {
-		samsung,pins = "gph-6", "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	uart3_data: uart3-data {
-		samsung,pins = "gph-6", "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	extuart_clk: extuart-clk {
-		samsung,pins = "gph-12";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	i2c0_bus: i2c0-bus {
-		samsung,pins = "gpe-14", "gpe-15";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	spi0_bus: spi0-bus {
-		samsung,pins = "gpe-11", "gpe-12", "gpe-13";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd0_clk: sd0-clk {
-		samsung,pins = "gpe-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd0_cmd: sd0-cmd {
-		samsung,pins = "gpe-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd0_bus1: sd0-bus1 {
-		samsung,pins = "gpe-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd0_bus4: sd0-bus4 {
-		samsung,pins = "gpe-8", "gpe-9", "gpe-10";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd1_cmd: sd1-cmd {
-		samsung,pins = "gpl-8";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd1_clk: sd1-clk {
-		samsung,pins = "gpl-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd1_bus1: sd1-bus1 {
-		samsung,pins = "gpl-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-
-	sd1_bus4: sd1-bus4 {
-		samsung,pins = "gpl-1", "gpl-2", "gpl-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-	};
-};
diff --git a/arch/arm/boot/dts/s3c2416-smdk2416.dts b/arch/arm/boot/dts/s3c2416-smdk2416.dts
deleted file mode 100644
index cb371bf72f64..000000000000
--- a/arch/arm/boot/dts/s3c2416-smdk2416.dts
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * SAMSUNG SMDK2416 board device tree source
- *
- * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
- */
-
-/dts-v1/;
-#include "s3c2416.dtsi"
-
-/ {
-	model = "SMDK2416";
-	compatible = "samsung,s3c2416";
-
-	memory@30000000 {
-		device_type = "memory";
-		reg =  <0x30000000 0x4000000>;
-	};
-
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		xti: xti@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			clock-frequency = <12000000>;
-			clock-output-names = "xti";
-			#clock-cells = <0>;
-		};
-	};
-};
-
-&rtc {
-	status = "okay";
-};
-
-&sdhci_0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sd1_clk>, <&sd1_cmd>,
-			<&sd1_bus1>, <&sd1_bus4>;
-	bus-width = <4>;
-	broken-cd;
-	status = "okay";
-};
-
-&sdhci_1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sd0_clk>, <&sd0_cmd>,
-			<&sd0_bus1>, <&sd0_bus4>;
-	bus-width = <4>;
-	cd-gpios = <&gpf 1 0>;
-	cd-inverted;
-	status = "okay";
-};
-
-&uart_0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_data>, <&uart0_fctl>;
-};
-
-&uart_1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_data>, <&uart1_fctl>;
-};
-
-&uart_2 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_data>;
-};
-
-&uart_3 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_data>;
-};
-
-&watchdog {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi
deleted file mode 100644
index 6adf64ea3ff2..000000000000
--- a/arch/arm/boot/dts/s3c2416.dtsi
+++ /dev/null
@@ -1,119 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Samsung's S3C2416 SoC device tree source
- *
- * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
- */
-
-#include <dt-bindings/clock/s3c2443.h>
-#include "s3c24xx.dtsi"
-#include "s3c2416-pinctrl.dtsi"
-
-/ {
-	model = "Samsung S3C2416 SoC";
-	compatible = "samsung,s3c2416";
-
-	aliases {
-		serial3 = &uart_3;
-	};
-
-	cpus {
-		cpu {
-			compatible = "arm,arm926ej-s";
-		};
-	};
-
-	interrupt-controller@4a000000 {
-		compatible = "samsung,s3c2416-irq";
-	};
-
-	clocks: clock-controller@4c000000 {
-		compatible = "samsung,s3c2416-clock";
-		reg = <0x4c000000 0x40>;
-		#clock-cells = <1>;
-	};
-
-	pinctrl@56000000 {
-		compatible = "samsung,s3c2416-pinctrl";
-	};
-
-	timer@51000000 {
-		clocks = <&clocks PCLK_PWM>;
-		clock-names = "timers";
-	};
-
-	uart_0: serial@50000000 {
-		compatible = "samsung,s3c2440-uart";
-		clock-names = "uart", "clk_uart_baud2",
-				"clk_uart_baud3";
-		clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>,
-				<&clocks SCLK_UART>;
-	};
-
-	uart_1: serial@50004000 {
-		compatible = "samsung,s3c2440-uart";
-		clock-names = "uart", "clk_uart_baud2",
-				"clk_uart_baud3";
-		clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>,
-				<&clocks SCLK_UART>;
-	};
-
-	uart_2: serial@50008000 {
-		compatible = "samsung,s3c2440-uart";
-		clock-names = "uart", "clk_uart_baud2",
-				"clk_uart_baud3";
-		clocks = <&clocks PCLK_UART2>, <&clocks PCLK_UART2>,
-				<&clocks SCLK_UART>;
-	};
-
-	uart_3: serial@5000c000 {
-		compatible = "samsung,s3c2440-uart";
-		reg = <0x5000C000 0x4000>;
-		interrupts = <1 18 24 4>, <1 18 25 4>;
-		clock-names = "uart", "clk_uart_baud2",
-				"clk_uart_baud3";
-		clocks = <&clocks PCLK_UART3>, <&clocks PCLK_UART3>,
-				<&clocks SCLK_UART>;
-		status = "disabled";
-	};
-
-	sdhci_1: sdhci@4ac00000 {
-		compatible = "samsung,s3c6410-sdhci";
-		reg = <0x4AC00000 0x100>;
-		interrupts = <0 0 21 3>;
-		clock-names = "hsmmc", "mmc_busclk.0",
-				"mmc_busclk.2";
-		clocks = <&clocks HCLK_HSMMC0>, <&clocks HCLK_HSMMC0>,
-				<&clocks MUX_HSMMC0>;
-		status = "disabled";
-	};
-
-	sdhci_0: sdhci@4a800000 {
-		compatible = "samsung,s3c6410-sdhci";
-		reg = <0x4A800000 0x100>;
-		interrupts = <0 0 20 3>;
-		clock-names = "hsmmc", "mmc_busclk.0",
-				"mmc_busclk.2";
-		clocks = <&clocks HCLK_HSMMC1>, <&clocks HCLK_HSMMC1>,
-				<&clocks MUX_HSMMC1>;
-		status = "disabled";
-	};
-
-	watchdog: watchdog@53000000 {
-		interrupts = <1 9 27 3>;
-		clocks = <&clocks PCLK_WDT>;
-		clock-names = "watchdog";
-	};
-
-	rtc: rtc@57000000 {
-		compatible = "samsung,s3c2416-rtc";
-		clocks = <&clocks PCLK_RTC>;
-		clock-names = "rtc";
-	};
-
-	i2c@54000000 {
-		compatible = "samsung,s3c2440-i2c";
-		clocks = <&clocks PCLK_I2C0>;
-		clock-names = "i2c";
-	};
-};
diff --git a/arch/arm/boot/dts/s3c24xx.dtsi b/arch/arm/boot/dts/s3c24xx.dtsi
deleted file mode 100644
index 6d8dd3cdd3c0..000000000000
--- a/arch/arm/boot/dts/s3c24xx.dtsi
+++ /dev/null
@@ -1,92 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Samsung's S3C24XX family device tree source
- *
- * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
- */
-
-/ {
-	compatible = "samsung,s3c24xx";
-	interrupt-parent = <&intc>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	aliases {
-		pinctrl0 = &pinctrl_0;
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-	};
-
-	intc:interrupt-controller@4a000000 {
-		compatible = "samsung,s3c2410-irq";
-		reg = <0x4a000000 0x100>;
-		interrupt-controller;
-		#interrupt-cells = <4>;
-	};
-
-	pinctrl_0: pinctrl@56000000 {
-		reg = <0x56000000 0x1000>;
-
-		wakeup-interrupt-controller {
-			compatible = "samsung,s3c2410-wakeup-eint";
-			interrupts = <0 0 0 3>,
-				     <0 0 1 3>,
-				     <0 0 2 3>,
-				     <0 0 3 3>,
-				     <0 0 4 4>,
-				     <0 0 5 4>;
-		};
-	};
-
-	timer@51000000 {
-		compatible = "samsung,s3c2410-pwm";
-		reg = <0x51000000 0x1000>;
-		interrupts = <0 0 10 3>, <0 0 11 3>, <0 0 12 3>, <0 0 13 3>, <0 0 14 3>;
-		#pwm-cells = <4>;
-	};
-
-	uart0: serial@50000000 {
-		compatible = "samsung,s3c2410-uart";
-		reg = <0x50000000 0x4000>;
-		interrupts = <1 28 0 4>, <1 28 1 4>;
-		status = "disabled";
-	};
-
-	uart1: serial@50004000 {
-		compatible = "samsung,s3c2410-uart";
-		reg = <0x50004000 0x4000>;
-		interrupts = <1 23 3 4>, <1 23 4 4>;
-		status = "disabled";
-	};
-
-	uart2: serial@50008000 {
-		compatible = "samsung,s3c2410-uart";
-		reg = <0x50008000 0x4000>;
-		interrupts = <1 15 6 4>, <1 15 7 4>;
-		status = "disabled";
-	};
-
-	watchdog@53000000 {
-		compatible = "samsung,s3c2410-wdt";
-		reg = <0x53000000 0x100>;
-		interrupts = <0 0 9 3>;
-		status = "disabled";
-	};
-
-	rtc@57000000 {
-		compatible = "samsung,s3c2410-rtc";
-		reg = <0x57000000 0x100>;
-		interrupts = <0 0 30 3>, <0 0 8 3>;
-		status = "disabled";
-	};
-
-	i2c@54000000 {
-		compatible = "samsung,s3c2410-i2c";
-		reg = <0x54000000 0x100>;
-		interrupts = <0 0 27 3>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-};
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
deleted file mode 100644
index 8ff70b856334..000000000000
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ /dev/null
@@ -1,509 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Samsung's S5PV210 based Galaxy Aries board device tree source
- */
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "s5pv210.dtsi"
-
-/ {
-	compatible = "samsung,aries", "samsung,s5pv210";
-
-	aliases {
-		i2c6 = &i2c_pmic;
-		i2c9 = &i2c_fuel;
-	};
-
-	memory@30000000 {
-		device_type = "memory";
-		reg = <0x30000000 0x05000000
-			0x40000000 0x10000000
-			0x50000000 0x08000000>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		mfc_left: region@43000000 {
-			compatible = "shared-dma-pool";
-			no-map;
-			reg = <0x43000000 0x2000000>;
-		};
-
-		mfc_right: region@51000000 {
-			compatible = "shared-dma-pool";
-			no-map;
-			reg = <0x51000000 0x2000000>;
-		};
-	};
-
-	vibrator_pwr: regulator-fixed-0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vibrator-en";
-		enable-active-high;
-		gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
-	};
-
-	wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_gpio_rst>;
-		post-power-on-delay-ms = <500>;
-		power-off-delay-us = <500>;
-	};
-
-	i2c_pmic: i2c-gpio-0 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pmic@66 {
-			compatible = "maxim,max8998";
-			reg = <0x66>;
-			interrupt-parent = <&gph0>;
-			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-
-			max8998,pmic-buck1-default-dvs-idx = <1>;
-			max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
-							<&gph0 4 GPIO_ACTIVE_HIGH>;
-			max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
-							<1050000>, <950000>;
-
-			max8998,pmic-buck2-default-dvs-idx = <0>;
-			max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
-			max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
-
-			regulators {
-				ldo2_reg: LDO2 {
-					regulator-name = "VALIVE_1.2V";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-
-					regulator-state-mem {
-						regulator-on-in-suspend;
-					};
-				};
-
-				ldo3_reg: LDO3 {
-					regulator-name = "VUSB_1.1V";
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo4_reg: LDO4 {
-					regulator-name = "VADC_3.3V";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo5_reg: LDO5 {
-					regulator-name = "VTF_2.8V";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo6_reg: LDO6 {
-					regulator-name = "LDO6";
-					regulator-min-microvolt = <1600000>;
-					regulator-max-microvolt = <3600000>;
-				};
-
-				ldo7_reg: LDO7 {
-					regulator-name = "VLCD_1.8V";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					/* Till we get panel driver */
-					regulator-always-on;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo8_reg: LDO8 {
-					regulator-name = "VUSB_3.3V";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo9_reg: LDO9 {
-					regulator-name = "VCC_2.8V_PDA";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					regulator-always-on;
-				};
-
-				ldo10_reg: LDO10 {
-					regulator-name = "VPLL_1.2V";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-
-					regulator-state-mem {
-						regulator-on-in-suspend;
-					};
-				};
-
-				ldo11_reg: LDO11 {
-					regulator-name = "CAM_AF_3.0V";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo12_reg: LDO12 {
-					regulator-name = "CAM_SENSOR_CORE_1.2V";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo13_reg: LDO13 {
-					regulator-name = "VGA_VDDIO_2.8V";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo14_reg: LDO14 {
-					regulator-name = "VGA_DVDD_1.8V";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo15_reg: LDO15 {
-					regulator-name = "CAM_ISP_HOST_2.8V";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo16_reg: LDO16 {
-					regulator-name = "VGA_AVDD_2.8V";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ldo17_reg: LDO17 {
-					regulator-name = "VCC_3.0V_LCD";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					/* Till we get panel driver */
-					regulator-always-on;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				buck1_reg: BUCK1 {
-					regulator-name = "vddarm";
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1500000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-						regulator-suspend-microvolt = <1250000>;
-					};
-				};
-
-				buck2_reg: BUCK2 {
-					regulator-name = "vddint";
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1500000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-						regulator-suspend-microvolt = <1100000>;
-					};
-				};
-
-				buck3_reg: BUCK3 {
-					regulator-name = "VCC_1.8V";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				buck4_reg: BUCK4 {
-					regulator-name = "CAM_ISP_CORE_1.2V";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-
-					regulator-state-mem {
-						regulator-off-in-suspend;
-					};
-				};
-
-				ap32khz_reg: EN32KHz-AP {
-					regulator-name = "32KHz AP";
-					regulator-always-on;
-				};
-
-				cp32khz_reg: EN32KHz-CP {
-					regulator-name = "32KHz CP";
-				};
-
-				vichg_reg: ENVICHG {
-					regulator-name = "VICHG";
-					regulator-always-on;
-				};
-
-				safe1_sreg: ESAFEOUT1 {
-					regulator-name = "SAFEOUT1";
-				};
-
-				safe2_sreg: ESAFEOUT2 {
-					regulator-name = "SAFEOUT2";
-				};
-			};
-		};
-	};
-
-	i2c_fuel: i2c-gpio-1 {
-		compatible = "i2c-gpio";
-		sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fuelgauge@36 {
-			compatible = "maxim,max17040";
-			interrupt-parent = <&vic0>;
-			interrupts = <7>;
-			reg = <0x36>;
-		};
-	};
-
-	vibrator: pwm-vibrator {
-		compatible = "pwm-vibrator";
-		pwms = <&pwm 1 44642 0>;
-		pwm-names = "enable";
-		vcc-supply = <&vibrator_pwr>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pwm1_out>;
-	};
-
-	poweroff: syscon-poweroff {
-		compatible = "syscon-poweroff";
-		regmap = <&pmu_syscon>;
-		offset = <0x681c>; /* PS_HOLD_CONTROL */
-		value = <0x5200>;
-	};
-};
-
-&fimd {
-	pinctrl-names = "default";
-	pinctrl-0 = <&lcd_clk &lcd_data24>;
-	status = "okay";
-
-	samsung,invert-vden;
-	samsung,invert-vclk;
-
-	display-timings {
-		timing-0 {
-			/* 480x800@60Hz */
-			clock-frequency = <25628040>;
-			hactive = <480>;
-			vactive = <800>;
-			hfront-porch = <16>;
-			hback-porch = <16>;
-			hsync-len = <2>;
-			vfront-porch = <28>;
-			vback-porch = <1>;
-			vsync-len = <2>;
-		};
-	};
-};
-
-&hsotg {
-	vusb_a-supply = <&ldo8_reg>;
-	vusb_d-supply = <&ldo3_reg>;
-	dr_mode = "peripheral";
-	status = "okay";
-};
-
-&i2c2 {
-	samsung,i2c-sda-delay = <100>;
-	samsung,i2c-max-bus-freq = <400000>;
-	samsung,i2c-slave-addr = <0x10>;
-	status = "okay";
-
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpj0>;
-		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_irq>;
-		reset-gpios = <&gpj1 3 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-&mfc {
-	memory-region = <&mfc_left>, <&mfc_right>;
-};
-
-&pinctrl0 {
-	wlan_bt_en: wlan-bt-en {
-		samsung,pins = "gpb-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-val = <1>;
-	};
-
-	wlan_gpio_rst: wlan-gpio-rst {
-		samsung,pins = "gpg1-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-	};
-
-	wifi_host_wake: wifi-host-wake {
-		samsung,pins = "gph2-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	bt_host_wake: bt-host-wake {
-		samsung,pins = "gph2-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	tf_detect: tf-detect {
-		samsung,pins = "gph3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	wifi_wake: wifi-wake {
-		samsung,pins = "gph3-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-	};
-
-	ts_irq: ts-irq {
-		samsung,pins = "gpj0-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-};
-
-&pwm {
-	samsung,pwm-outputs = <1>;
-};
-
-&sdhci1 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	bus-width = <4>;
-	max-frequency = <38400000>;
-	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
-	pinctrl-names = "default";
-	cap-sd-highspeed;
-	cap-mmc-highspeed;
-
-	mmc-pwrseq = <&wifi_pwrseq>;
-	non-removable;
-	status = "okay";
-
-	wlan@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-		interrupt-parent = <&gph2>;
-		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "host-wake";
-	};
-};
-
-&sdhci2 {
-	bus-width = <4>;
-	cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&ldo5_reg>;
-	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&uart0 {
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		max-speed = <115200>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake>;
-		shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>;
-		device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
-		host-wakeup-gpios = <&gph2 5 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&usbphy {
-	status = "okay";
-	vbus-supply = <&safe1_sreg>;
-};
-
-&xusbxti {
-	clock-frequency = <24000000>;
-};
diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
deleted file mode 100644
index 07a8d9bbe5b8..000000000000
--- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts
+++ /dev/null
@@ -1,38 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include "s5pv210-aries.dtsi"
-
-/ {
-	model = "Samsung Galaxy S Fascinate 4G (SGH-T959P) based on S5PV210";
-	compatible = "samsung,fascinate4g", "samsung,aries", "samsung,s5pv210";
-
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "power";
-			gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-
-		vol-down {
-			label = "volume_down";
-			gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		vol-up {
-			label = "volume_up";
-			gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/s5pv210-galaxys.dts b/arch/arm/boot/dts/s5pv210-galaxys.dts
deleted file mode 100644
index cf161bbfbacf..000000000000
--- a/arch/arm/boot/dts/s5pv210-galaxys.dts
+++ /dev/null
@@ -1,70 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include "s5pv210-aries.dtsi"
-
-/ {
-	model = "Samsung Galaxy S1 (GT-I9000) based on S5PV210";
-	compatible = "samsung,galaxys", "samsung,aries", "samsung,s5pv210";
-
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	nand_pwrseq: nand-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpj2 7 GPIO_ACTIVE_LOW>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&massmemory_en>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "power";
-			gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-
-		vol-down {
-			label = "volume_down";
-			gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		vol-up {
-			label = "volume_up";
-			gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		home {
-			label = "home";
-			gpios = <&gph3 5 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_HOME>;
-			wakeup-source;
-		};
-	};
-};
-
-&pinctrl0 {
-	massmemory_en: massmemory-en {
-		samsung,pins = "gpj2-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-};
-
-&sdhci0 {
-	bus-width = <4>;
-	non-removable;
-	mmc-pwrseq = <&nand_pwrseq>;
-	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
-	pinctrl-names = "default";
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/s5pv210-pinctrl.dtsi b/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
deleted file mode 100644
index 7f0c9d447871..000000000000
--- a/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
+++ /dev/null
@@ -1,840 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Samsung's S5PV210 SoC device tree source
- *
- * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
- *
- * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
- * Tomasz Figa <t.figa@samsung.com>
- *
- * Samsung's S5PV210 SoC device nodes are listed in this file. S5PV210
- * based board files can include this file and provide values for board specfic
- * bindings.
- *
- * Note: This file does not include device nodes for all the controllers in
- * S5PV210 SoC. As device tree coverage for S5PV210 increases, additional
- * nodes can be added to this file.
- */
-
-#include <dt-bindings/pinctrl/samsung.h>
-
-&pinctrl0 {
-	gpa0: gpa0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpa1: gpa1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpb: gpb {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpc0: gpc0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpc1: gpc1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpd0: gpd0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpd1: gpd1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpe0: gpe0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpe1: gpe1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpf0: gpf0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpf1: gpf1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpf2: gpf2 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpf3: gpf3 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpg0: gpg0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpg1: gpg1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpg2: gpg2 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpg3: gpg3 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpj0: gpj0 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpj1: gpj1 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpj2: gpj2 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpj3: gpj3 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpj4: gpj4 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gpgi: gpgi {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp01: mp01 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp02: mp02 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp03: mp03 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp04: mp04 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp05: mp05 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp06: mp06 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	mp07: mp07 {
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gph0: gph0 {
-		gpio-controller;
-		interrupt-controller;
-		interrupt-parent = <&vic0>;
-		interrupts = <0>, <1>, <2>, <3>,
-				<4>, <5>, <6>, <7>;
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-	};
-
-	gph1: gph1 {
-		gpio-controller;
-		interrupt-controller;
-		interrupt-parent = <&vic0>;
-		interrupts = <8>, <9>, <10>, <11>,
-				<12>, <13>, <14>, <15>;
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-	};
-
-	gph2: gph2 {
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	gph3: gph3 {
-		gpio-controller;
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-	};
-
-	uart0_data: uart0-data {
-		samsung,pins = "gpa0-0", "gpa0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart0_fctl: uart0-fctl {
-		samsung,pins = "gpa0-2", "gpa0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart1_data: uart1-data {
-		samsung,pins = "gpa0-4", "gpa0-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart1_fctl: uart1-fctl {
-		samsung,pins = "gpa0-6", "gpa0-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart2_data: uart2-data {
-		samsung,pins = "gpa1-0", "gpa1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart2_fctl: uart2-fctl {
-		samsung,pins = "gpa1-2", "gpa1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart3_data: uart3-data {
-		samsung,pins = "gpa1-2", "gpa1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	uart_audio: uart-audio {
-		samsung,pins = "gpa1-2", "gpa1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	spi0_bus: spi0-bus {
-		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	spi1_bus: spi1-bus {
-		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2s0_bus: i2s0-bus {
-		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
-				"gpi-4", "gpi-5", "gpi-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2s1_bus: i2s1-bus {
-		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
-				"gpc0-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2s2_bus: i2s2-bus {
-		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
-				"gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	pcm1_bus: pcm1-bus {
-		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
-				"gpc0-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	ac97_bus: ac97-bus {
-		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
-				"gpc0-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2s2_bus: i2s2-bus {
-		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
-				"gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	pcm2_bus: pcm2-bus {
-		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
-				"gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	spdif_bus: spdif-bus {
-		samsung,pins = "gpc1-0", "gpc1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	spi2_bus: spi2-bus {
-		samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2c0_bus: i2c0-bus {
-		samsung,pins = "gpd1-0", "gpd1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2c1_bus: i2c1-bus {
-		samsung,pins = "gpd1-2", "gpd1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	i2c2_bus: i2c2-bus {
-		samsung,pins = "gpd1-4", "gpd1-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	pwm0_out: pwm0-out {
-		samsung,pins = "gpd0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	pwm1_out: pwm1-out {
-		samsung,pins = "gpd0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	pwm2_out: pwm2-out {
-		samsung,pins = "gpd0-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	pwm3_out: pwm3-out {
-		samsung,pins = "gpd0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row0: keypad-row-0 {
-		samsung,pins = "gph3-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row1: keypad-row-1 {
-		samsung,pins = "gph3-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row2: keypad-row-2 {
-		samsung,pins = "gph3-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row3: keypad-row-3 {
-		samsung,pins = "gph3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row4: keypad-row-4 {
-		samsung,pins = "gph3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row5: keypad-row-5 {
-		samsung,pins = "gph3-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row6: keypad-row-6 {
-		samsung,pins = "gph3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_row7: keypad-row-7 {
-		samsung,pins = "gph3-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col0: keypad-col-0 {
-		samsung,pins = "gph2-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col1: keypad-col-1 {
-		samsung,pins = "gph2-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col2: keypad-col-2 {
-		samsung,pins = "gph2-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col3: keypad-col-3 {
-		samsung,pins = "gph2-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col4: keypad-col-4 {
-		samsung,pins = "gph2-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col5: keypad-col-5 {
-		samsung,pins = "gph2-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col6: keypad-col-6 {
-		samsung,pins = "gph2-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	keypad_col7: keypad-col-7 {
-		samsung,pins = "gph2-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	sd0_clk: sd0-clk {
-		samsung,pins = "gpg0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd0_cmd: sd0-cmd {
-		samsung,pins = "gpg0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd0_cd: sd0-cd {
-		samsung,pins = "gpg0-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd0_bus1: sd0-bus-width1 {
-		samsung,pins = "gpg0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd0_bus4: sd0-bus-width4 {
-		samsung,pins = "gpg0-3", "gpg0-4", "gpg0-5", "gpg0-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd0_bus8: sd0-bus-width8 {
-		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd1_clk: sd1-clk {
-		samsung,pins = "gpg1-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd1_cmd: sd1-cmd {
-		samsung,pins = "gpg1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd1_cd: sd1-cd {
-		samsung,pins = "gpg1-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd1_bus1: sd1-bus-width1 {
-		samsung,pins = "gpg1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd1_bus4: sd1-bus-width4 {
-		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd2_clk: sd2-clk {
-		samsung,pins = "gpg2-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd2_cmd: sd2-cmd {
-		samsung,pins = "gpg2-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd2_cd: sd2-cd {
-		samsung,pins = "gpg2-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd2_bus1: sd2-bus-width1 {
-		samsung,pins = "gpg2-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd2_bus4: sd2-bus-width4 {
-		samsung,pins = "gpg2-3", "gpg2-4", "gpg2-5", "gpg2-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd2_bus8: sd2-bus-width8 {
-		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd3_clk: sd3-clk {
-		samsung,pins = "gpg3-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd3_cmd: sd3-cmd {
-		samsung,pins = "gpg3-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd3_cd: sd3-cd {
-		samsung,pins = "gpg3-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd3_bus1: sd3-bus-width1 {
-		samsung,pins = "gpg3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	sd3_bus4: sd3-bus-width4 {
-		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	eint0: ext-int0 {
-		samsung,pins = "gph0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	eint8: ext-int8 {
-		samsung,pins = "gph1-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	eint15: ext-int15 {
-		samsung,pins = "gph1-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	eint16: ext-int16 {
-		samsung,pins = "gph2-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	eint31: ext-int31 {
-		samsung,pins = "gph3-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	cam_port_a_io: cam-port-a-io {
-		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
-				"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
-				"gpe1-0", "gpe1-1", "gpe1-2", "gpe1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	cam_port_a_clk_active: cam-port-a-clk-active {
-		samsung,pins = "gpe1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	cam_port_a_clk_idle: cam-port-a-clk-idle {
-		samsung,pins = "gpe1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	cam_port_b_io: cam-port-b-io {
-		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
-				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
-				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	cam_port_b_clk_active: cam-port-b-clk-active {
-		samsung,pins = "gpj1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
-	};
-
-	cam_port_b_clk_idle: cam-port-b-clk-idle {
-		samsung,pins = "gpj1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-		lcd_ctrl: lcd-ctrl {
-		samsung,pins = "gpd0-0", "gpd0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	lcd_sync: lcd-sync {
-		samsung,pins = "gpf0-0", "gpf0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	lcd_clk: lcd-clk {
-		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-
-	lcd_data24: lcd-data-width24 {
-		samsung,pins =  "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
-				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
-				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
-				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
-				"gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7",
-				"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
-	};
-};
diff --git a/arch/arm/boot/dts/samsung/Makefile b/arch/arm/boot/dts/samsung/Makefile
new file mode 100644
index 000000000000..7becf36656b1
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/Makefile
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_EXYNOS3) += \
+	exynos3250-artik5-eval.dtb \
+	exynos3250-monk.dtb \
+	exynos3250-rinato.dtb
+dtb-$(CONFIG_ARCH_EXYNOS4) += \
+	exynos4210-i9100.dtb \
+	exynos4210-origen.dtb \
+	exynos4210-smdkv310.dtb \
+	exynos4210-trats.dtb \
+	exynos4210-universal_c210.dtb \
+	exynos4212-tab3-3g8.dtb \
+	exynos4212-tab3-lte8.dtb \
+	exynos4212-tab3-wifi8.dtb \
+	exynos4412-i9300.dtb \
+	exynos4412-i9305.dtb \
+	exynos4412-itop-elite.dtb \
+	exynos4412-n710x.dtb \
+	exynos4412-odroidu3.dtb \
+	exynos4412-odroidx.dtb \
+	exynos4412-odroidx2.dtb \
+	exynos4412-origen.dtb \
+	exynos4412-p4note-n8010.dtb \
+	exynos4412-smdk4412.dtb \
+	exynos4412-tiny4412.dtb \
+	exynos4412-trats2.dtb
+dtb-$(CONFIG_ARCH_EXYNOS5) += \
+	exynos5250-arndale.dtb \
+	exynos5250-smdk5250.dtb \
+	exynos5250-snow.dtb \
+	exynos5250-snow-rev5.dtb \
+	exynos5250-spring.dtb \
+	exynos5260-xyref5260.dtb \
+	exynos5410-odroidxu.dtb \
+	exynos5410-smdk5410.dtb \
+	exynos5420-arndale-octa.dtb \
+	exynos5420-peach-pit.dtb \
+	exynos5420-smdk5420.dtb \
+	exynos5420-chagall-wifi.dtb \
+	exynos5420-klimt-wifi.dtb \
+	exynos5422-odroidhc1.dtb \
+	exynos5422-odroidxu3.dtb \
+	exynos5422-odroidxu3-lite.dtb \
+	exynos5422-odroidxu4.dtb \
+	exynos5422-samsung-k3g.dtb \
+	exynos5800-peach-pi.dtb
+dtb-$(CONFIG_ARCH_S3C64XX) += \
+	s3c6410-mini6410.dtb \
+	s3c6410-smdk6410.dtb
+dtb-$(CONFIG_ARCH_S5PV210) += \
+	s5pv210-aquila.dtb \
+	s5pv210-fascinate4g.dtb \
+	s5pv210-galaxys.dtb \
+	s5pv210-goni.dtb \
+	s5pv210-smdkc110.dtb \
+	s5pv210-smdkv210.dtb \
+	s5pv210-torbreck.dtb
diff --git a/arch/arm/boot/dts/exynos-mfc-reserved-memory.dtsi b/arch/arm/boot/dts/samsung/exynos-mfc-reserved-memory.dtsi
index 1dbf3bbff8d3..597ade3e252f 100644
--- a/arch/arm/boot/dts/exynos-mfc-reserved-memory.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos-mfc-reserved-memory.dtsi
@@ -11,14 +11,14 @@
 		#size-cells = <1>;
 		ranges;
 
-		mfc_left: region_mfc_left {
+		mfc_left: region-mfc-left {
 			compatible = "shared-dma-pool";
 			no-map;
 			size = <0x2400000>;
 			alignment = <0x100000>;
 		};
 
-		mfc_right: region_mfc_right {
+		mfc_right: region-mfc-right {
 			compatible = "shared-dma-pool";
 			no-map;
 			size = <0x800000>;
diff --git a/arch/arm/boot/dts/samsung/exynos-pinctrl.h b/arch/arm/boot/dts/samsung/exynos-pinctrl.h
new file mode 100644
index 000000000000..e3a6df95281c
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos-pinctrl.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung Exynos DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_EXYNOS_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_EXYNOS_PINCTRL_H__
+
+#define EXYNOS_PIN_PULL_NONE		0
+#define EXYNOS_PIN_PULL_DOWN		1
+#define EXYNOS_PIN_PULL_UP		3
+
+/* Pin function in power down mode */
+#define EXYNOS_PIN_PDN_OUT0		0
+#define EXYNOS_PIN_PDN_OUT1		1
+#define EXYNOS_PIN_PDN_INPUT		2
+#define EXYNOS_PIN_PDN_PREV		3
+
+/* Drive strengths for Exynos3250, Exynos4 (all) and Exynos5250 */
+#define EXYNOS4_PIN_DRV_LV1		0
+#define EXYNOS4_PIN_DRV_LV2		2
+#define EXYNOS4_PIN_DRV_LV3		1
+#define EXYNOS4_PIN_DRV_LV4		3
+
+/* Drive strengths for Exynos5260 */
+#define EXYNOS5260_PIN_DRV_LV1		0
+#define EXYNOS5260_PIN_DRV_LV2		1
+#define EXYNOS5260_PIN_DRV_LV4		2
+#define EXYNOS5260_PIN_DRV_LV6		3
+
+/*
+ * Drive strengths for Exynos5410, Exynos542x, Exynos5800 and Exynos850 (except
+ * GPIO_HSI block)
+ */
+#define EXYNOS5420_PIN_DRV_LV1		0
+#define EXYNOS5420_PIN_DRV_LV2		1
+#define EXYNOS5420_PIN_DRV_LV3		2
+#define EXYNOS5420_PIN_DRV_LV4		3
+
+#define EXYNOS_PIN_FUNC_INPUT		0
+#define EXYNOS_PIN_FUNC_OUTPUT		1
+#define EXYNOS_PIN_FUNC_2		2
+#define EXYNOS_PIN_FUNC_3		3
+#define EXYNOS_PIN_FUNC_4		4
+#define EXYNOS_PIN_FUNC_5		5
+#define EXYNOS_PIN_FUNC_6		6
+#define EXYNOS_PIN_FUNC_EINT		0xf
+#define EXYNOS_PIN_FUNC_F		EXYNOS_PIN_FUNC_EINT
+
+#endif /* __DTS_ARM_SAMSUNG_EXYNOS_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/exynos-syscon-restart.dtsi b/arch/arm/boot/dts/samsung/exynos-syscon-restart.dtsi
index ecf416690a15..bc9a78f6d4b7 100644
--- a/arch/arm/boot/dts/exynos-syscon-restart.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos-syscon-restart.dtsi
@@ -7,7 +7,7 @@
 	poweroff: syscon-poweroff {
 		compatible = "syscon-poweroff";
 		regmap = <&pmu_system_controller>;
-		offset = <0x330C>; /* PS_HOLD_CONTROL */
+		offset = <0x330c>; /* PS_HOLD_CONTROL */
 		mask = <0x5200>; /* reset value */
 	};
 
diff --git a/arch/arm/boot/dts/exynos3250-artik5-eval.dts b/arch/arm/boot/dts/samsung/exynos3250-artik5-eval.dts
index 20446a846a98..660cc7fac4db 100644
--- a/arch/arm/boot/dts/exynos3250-artik5-eval.dts
+++ b/arch/arm/boot/dts/samsung/exynos3250-artik5-eval.dts
@@ -16,6 +16,10 @@
 	model = "Samsung ARTIK5 evaluation board";
 	compatible = "samsung,artik5-eval", "samsung,artik5",
 			"samsung,exynos3250", "samsung,exynos3";
+
+	aliases {
+		mmc0 = &mshc_2;
+	};
 };
 
 &mshc_2 {
@@ -37,3 +41,29 @@
 &serial_2 {
 	status = "okay";
 };
+
+&spi_0 {
+	status = "okay";
+	cs-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>, <0>;
+
+	assigned-clocks = <&cmu CLK_MOUT_SPI0>, <&cmu CLK_DIV_SPI0>,
+			  <&cmu CLK_DIV_SPI0_PRE>, <&cmu CLK_SCLK_SPI0>;
+	assigned-clock-parents = <&cmu CLK_DIV_MPLL_PRE>, /* for: CLK_MOUT_SPI0 */
+				 <&cmu CLK_MOUT_SPI0>,    /* for: CLK_DIV_SPI0 */
+				 <&cmu CLK_DIV_SPI0>,     /* for: CLK_DIV_SPI0_PRE */
+				 <&cmu CLK_DIV_SPI0_PRE>; /* for: CLK_SCLK_SPI0 */
+
+	ethernet@0 {
+		compatible = "asix,ax88796c";
+		reg = <0x0>;
+		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a boot-loader */
+		interrupt-parent = <&gpx2>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <40000000>;
+		reset-gpios = <&gpe0 2 GPIO_ACTIVE_LOW>;
+
+		controller-data {
+			samsung,spi-feedback-delay = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos3250-artik5.dtsi b/arch/arm/boot/dts/samsung/exynos3250-artik5.dtsi
index dee35e3a5c4b..3fdd922e635c 100644
--- a/arch/arm/boot/dts/exynos3250-artik5.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos3250-artik5.dtsi
@@ -17,13 +17,18 @@
 / {
 	compatible = "samsung,artik5", "samsung,exynos3250", "samsung,exynos3";
 
+	aliases {
+		mmc0 = &mshc_0;
+		mmc1 = &mshc_1;
+	};
+
 	chosen {
 		stdout-path = &serial_2;
 	};
 
 	memory@40000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x1ff00000>;
+		reg = <0x40000000 0x1f800000>;
 	};
 
 	firmware@205f000 {
@@ -55,6 +60,10 @@
 	assigned-clock-rates = <6000000>;
 };
 
+&cmu {
+	clocks = <&xusbxti>;
+};
+
 &cpu0 {
 	cpu0-supply = <&buck2_reg>;
 };
@@ -72,10 +81,10 @@
 	samsung,i2c-max-bus-freq = <100000>;
 	status = "okay";
 
-	s2mps14_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s2mps14-pmic";
 		interrupt-parent = <&gpx3>;
-		interrupts = <5 IRQ_TYPE_NONE>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s2mps14_irq>;
 		reg = <0x66>;
@@ -317,6 +326,7 @@
 	vmmc-supply = <&ldo12_reg>;
 	clock-frequency = <100000000>;
 	max-frequency = <100000000>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <1>;
 	samsung,dw-mshc-sdr-timing = <0 1>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
@@ -352,7 +362,15 @@
 };
 
 &pinctrl_1 {
-	wlanen: wlanen {
+	bten: bten-pins {
+		samsung,pins = "gpx1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	wlanen: wlanen-pins {
 		samsung,pins = "gpx2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -360,10 +378,26 @@
 		samsung,pin-val = <1>;
 	};
 
-	s2mps14_irq: s2mps14-irq {
+	s2mps14_irq: s2mps14-irq-pins {
 		samsung,pins = "gpx3-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
+
+	bthostwake: bthostwake-pins {
+		samsung,pins = "gpx3-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	btwake: btwake-pins {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT0>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_DOWN>;
+	};
 };
 
 &rtc {
@@ -372,6 +406,23 @@
 	status = "okay";
 };
 
+&serial_0 {
+	assigned-clocks = <&cmu CLK_SCLK_UART0>;
+	assigned-clock-rates = <100000000>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bten &btwake &bthostwake>;
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpx1 7 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx3 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&s2mps14_osc S2MPS11_CLK_BT>;
+	};
+};
+
 &tmu {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/samsung/exynos3250-monk.dts
index 248bd372fe70..2de877d4ccc5 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/samsung/exynos3250-monk.dts
@@ -22,22 +22,23 @@
 
 	aliases {
 		i2c7 = &i2c_max77836;
+		mmc0 = &mshc_0;
 	};
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x1ff00000>;
+		reg = <0x40000000 0x1ff00000>;
 	};
 
 	firmware@205f000 {
 		compatible = "samsung,secure-firmware";
-		reg = <0x0205F000 0x1000>;
+		reg = <0x0205f000 0x1000>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power_key {
+		power-key {
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "power key";
@@ -57,18 +58,19 @@
 
 	i2c_max77836: i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpd0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpd0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		max77836: subpmic@25 {
+		max77836: pmic@25 {
 			compatible = "maxim,max77836";
 			interrupt-parent = <&gpx1>;
 			interrupts = <5 IRQ_TYPE_NONE>;
 			reg = <0x25>;
 			wakeup-source;
 
-			muic: max77836-muic {
+			extcon {
 				compatible = "maxim,max77836-muic";
 			};
 
@@ -141,7 +143,7 @@
 	assigned-clock-rates = <6000000>;
 
 	thermistor-ap {
-		compatible = "ntc,ncp15wb473";
+		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
 		pullup-ohm = <100000>;
 		pulldown-ohm = <100000>;
@@ -149,7 +151,7 @@
 	};
 
 	thermistor-battery {
-		compatible = "ntc,ncp15wb473";
+		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
 		pullup-ohm = <100000>;
 		pulldown-ohm = <100000>;
@@ -163,6 +165,10 @@
 	status = "okay";
 };
 
+&cmu {
+	clocks = <&xusbxti>;
+};
+
 &cpu0 {
 	cpu0-supply = <&buck2_reg>;
 };
@@ -192,10 +198,10 @@
 	samsung,i2c-max-bus-freq = <100000>;
 	status = "okay";
 
-	s2mps14_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s2mps14-pmic";
 		interrupt-parent = <&gpx0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x66>;
 		wakeup-source;
 
@@ -433,12 +439,12 @@
 	broken-cd;
 	non-removable;
 	cap-mmc-highspeed;
-	desc-num = <4>;
 	mmc-hs200-1_8v;
 	card-detect-delay = <200>;
 	vmmc-supply = <&vemmc_reg>;
 	clock-frequency = <100000000>;
 	max-frequency = <100000000>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <1>;
 	samsung,dw-mshc-sdr-timing = <0 1>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos3250-pinctrl.dtsi
index dff3c6e3aa1f..07828551d4b3 100644
--- a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos3250-pinctrl.dtsi
@@ -5,54 +5,29 @@
  * Copyright (c) 2014 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * Samsung's Exynos3250 SoCs pin-mux and pin-config optiosn are listed as device
- * tree nodes are listed in this file.
+ * Samsung's Exynos3250 SoCs pin-mux and pin-config options are listed as device
+ * tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 #define PIN_IN(_pin, _pull, _drv)					\
-	_pin {								\
+	pin- ## _pin {							\
 		samsung,pins = #_pin;					\
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;		\
 		samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>;		\
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
 	}
 
-#define PIN_OUT(_pin, _drv)						\
-	_pin {								\
-		samsung,pins = #_pin;					\
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;	\
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;		\
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
-	}
-
-#define PIN_OUT_SET(_pin, _val, _drv)					\
-	_pin {								\
-		samsung,pins = #_pin;					\
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;	\
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;		\
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
-		samsung,pin-val = <_val>;				\
-	}
-
-#define PIN_CFG(_pin, _sel, _pull, _drv)				\
-	_pin {								\
-		samsung,pins = #_pin;					\
-		samsung,pin-function = <_sel>;				\
-		samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>;		\
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
-	}
-
 #define PIN_SLP(_pin, _mode, _pull)					\
-	_pin {								\
+	pin- ## _pin {							\
 		samsung,pins = #_pin;					\
 		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_ ##_mode>;	\
 		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_ ##_pull>;	\
 	}
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -60,7 +35,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -68,7 +43,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -76,7 +51,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -84,7 +59,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -92,7 +67,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -100,7 +75,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -108,84 +83,84 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -193,7 +168,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -201,63 +176,63 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	mipi0_clk: mipi0-clk {
+	mipi0_clk: mipi0-clk-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -266,22 +241,22 @@
 };
 
 &pinctrl_1 {
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpe2: gpe2 {
+	gpe2: gpe2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -289,7 +264,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -297,7 +272,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -305,7 +280,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl0: gpl0 {
+	gpl0: gpl0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -313,7 +288,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm0: gpm0 {
+	gpm0: gpm0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -321,7 +296,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm1: gpm1 {
+	gpm1: gpm1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -329,7 +304,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm2: gpm2 {
+	gpm2: gpm2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -337,7 +312,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm3: gpm3 {
+	gpm3: gpm3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -345,7 +320,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm4: gpm4 {
+	gpm4: gpm4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -353,7 +328,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -370,7 +345,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -387,7 +362,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -395,7 +370,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -403,126 +378,126 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_rdqs: sd0-rdqs {
+	sd0_rdqs: sd0-rdqs-pins {
 		samsung,pins = "gpk0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpl0-0", "gpl0-1", "gpl0-2", "gpl0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpk1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpk1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpk1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpk2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpk2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpk2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpk2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpk2-4", "gpk2-5", "gpk2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_io: cam-port-b-io {
+	cam_port_b_io: cam-port-b-io-pins {
 		samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
 				"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
 				"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
@@ -531,35 +506,35 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_b_clk_active: cam-port-b-clk-active {
+	cam_port_b_clk_active: cam-port-b-clk-active-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_clk_idle: cam-port-b-clk-idle {
+	cam_port_b_clk_idle: cam-port-b-clk-idle-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c0: fimc-is-i2c0 {
+	fimc_is_i2c0: fimc-is-i2c0-pins {
 		samsung,pins = "gpm4-0", "gpm4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c1: fimc-is-i2c1 {
+	fimc_is_i2c1: fimc-is-i2c1-pins {
 		samsung,pins = "gpm4-2", "gpm4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_uart: fimc-is-uart {
+	fimc_is_uart: fimc-is-uart-pins {
 		samsung,pins = "gpm3-5", "gpm3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/samsung/exynos3250-rinato.dts
index 86c26a4edfd7..88fb3e68ff02 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/samsung/exynos3250-rinato.dts
@@ -19,9 +19,12 @@
 / {
 	model = "Samsung Rinato board";
 	compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
+	chassis-type = "watch";
 
 	aliases {
 		i2c7 = &i2c_max77836;
+		mmc0 = &mshc_0;
+		mmc1 = &mshc_1;
 	};
 
 	chosen {
@@ -30,18 +33,18 @@
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x1ff00000>;
+		reg = <0x40000000 0x1ff00000>;
 	};
 
 	firmware@205f000 {
 		compatible = "samsung,secure-firmware";
-		reg = <0x0205F000 0x1000>;
+		reg = <0x0205f000 0x1000>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power_key {
+		power-key {
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "power key";
@@ -50,20 +53,26 @@
 		};
 	};
 
+	wlan_pwrseq: mshc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
+	};
+
 	i2c_max77836: i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpd0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpd0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		max77836: subpmic@25 {
+		max77836: pmic@25 {
 			compatible = "maxim,max77836";
 			interrupt-parent = <&gpx1>;
 			interrupts = <5 IRQ_TYPE_NONE>;
 			reg = <0x25>;
 			wakeup-source;
 
-			muic: max77836-muic {
+			extcon {
 				compatible = "maxim,max77836-muic";
 			};
 
@@ -136,7 +145,7 @@
 	assigned-clock-rates = <6000000>;
 
 	thermistor-ap {
-		compatible = "ntc,ncp15wb473";
+		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
 		pullup-ohm = <100000>;
 		pulldown-ohm = <100000>;
@@ -144,7 +153,7 @@
 	};
 
 	thermistor-battery {
-		compatible = "ntc,ncp15wb473";
+		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
 		pullup-ohm = <100000>;
 		pulldown-ohm = <100000>;
@@ -199,6 +208,10 @@
 	status = "okay";
 };
 
+&cmu {
+	clocks = <&xusbxti>;
+};
+
 &cpu0 {
 	cpu0-supply = <&buck2_reg>;
 };
@@ -239,7 +252,7 @@
 	i80-if-timings {
 		cs-setup = <0>;
 		wr-setup = <0>;
-		wr-act = <1>;
+		wr-active = <1>;
 		wr-hold = <0>;
 	};
 };
@@ -257,10 +270,10 @@
 	samsung,i2c-max-bus-freq = <100000>;
 	status = "okay";
 
-	s2mps14_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s2mps14-pmic";
 		interrupt-parent = <&gpx0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x66>;
 		wakeup-source;
 
@@ -605,17 +618,15 @@
 };
 
 &mshc_0 {
-	#address-cells = <1>;
-	#size-cells = <0>;
 	broken-cd;
 	non-removable;
 	cap-mmc-highspeed;
-	desc-num = <4>;
 	mmc-hs200-1_8v;
 	card-detect-delay = <200>;
 	vmmc-supply = <&ldo12_reg>;
 	clock-frequency = <100000000>;
 	max-frequency = <100000000>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <1>;
 	samsung,dw-mshc-sdr-timing = <0 1>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
@@ -625,10 +636,48 @@
 	status = "okay";
 };
 
+&mshc_1 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	non-removable;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	samsung,dw-mshc-ciu-div = <1>;
+	samsung,dw-mshc-sdr-timing = <0 1>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus1 &sd1_bus4>;
+	bus-width = <4>;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpx1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
 &serial_0 {
 	assigned-clocks = <&cmu CLK_SCLK_UART0>;
 	assigned-clock-rates = <100000000>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpe0 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&s2mps14_osc S2MPS11_CLK_BT>;
+	};
 };
 
 &serial_1 {
diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/samsung/exynos3250.dtsi
index b016b0b68306..3f1015edab43 100644
--- a/arch/arm/boot/dts/exynos3250.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos3250.dtsi
@@ -6,7 +6,7 @@
  *		http://www.samsung.com
  *
  * Samsung's Exynos3250 SoC device nodes are listed in this file. Exynos3250
- * based board files can include this file and provide values for board specfic
+ * based board files can include this file and provide values for board specific
  * bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
@@ -28,9 +28,6 @@
 	aliases {
 		pinctrl0 = &pinctrl_0;
 		pinctrl1 = &pinctrl_1;
-		mshc0 = &mshc_0;
-		mshc1 = &mshc_1;
-		mshc2 = &mshc_2;
 		spi0 = &spi_0;
 		spi1 = &spi_1;
 		i2c0 = &i2c_0;
@@ -46,10 +43,172 @@
 		serial2 = &serial_2;
 	};
 
+	bus_dmc: bus-dmc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_dmc CLK_DIV_DMC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		status = "disabled";
+
+		bus_dmc_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-50000000 {
+				opp-hz = /bits/ 64 <50000000>;
+				opp-microvolt = <800000>;
+			};
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+				opp-microvolt = <800000>;
+			};
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+				opp-microvolt = <800000>;
+			};
+			opp-200000000 {
+				opp-hz = /bits/ 64 <200000000>;
+				opp-microvolt = <825000>;
+			};
+			opp-400000000 {
+				opp-hz = /bits/ 64 <400000000>;
+				opp-microvolt = <875000>;
+			};
+		};
+	};
+
+	bus_fsys: bus-fsys {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_200>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_isp: bus-isp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_266>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_isp_opp_table>;
+		status = "disabled";
+
+		bus_isp_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-50000000 {
+				opp-hz = /bits/ 64 <50000000>;
+			};
+			opp-80000000 {
+				opp-hz = /bits/ 64 <80000000>;
+			};
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+			opp-200000000 {
+				opp-hz = /bits/ 64 <200000000>;
+			};
+			opp-300000000 {
+				opp-hz = /bits/ 64 <300000000>;
+			};
+		};
+	};
+
+	bus_lcd0: bus-lcd0 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_160>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_leftbus: bus-leftbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_GDL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mcuisp: bus-mcuisp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_mcuisp_opp_table>;
+		status = "disabled";
+
+		bus_mcuisp_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-50000000 {
+				opp-hz = /bits/ 64 <50000000>;
+			};
+			opp-80000000 {
+				opp-hz = /bits/ 64 <80000000>;
+			};
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+			opp-200000000 {
+				opp-hz = /bits/ 64 <200000000>;
+			};
+			opp-400000000 {
+				opp-hz = /bits/ 64 <400000000>;
+			};
+		};
+	};
+
+	bus_mfc: bus-mfc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_SCLK_MFC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_peril: bus-peril {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_100>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_peril_opp_table>;
+		status = "disabled";
+
+		bus_peril_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-50000000 {
+				opp-hz = /bits/ 64 <50000000>;
+			};
+			opp-80000000 {
+				opp-hz = /bits/ 64 <80000000>;
+			};
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+		};
+	};
+
+	bus_rightbus: bus-rightbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_GDR>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
@@ -97,32 +256,49 @@
 		};
 	};
 
-	fixed-rate-clocks {
-		#address-cells = <1>;
-		#size-cells = <0>;
+	xusbxti: clock-0 {
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+		#clock-cells = <0>;
+		clock-output-names = "xusbxti";
+	};
 
-		xusbxti: clock@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			clock-frequency = <0>;
-			#clock-cells = <0>;
-			clock-output-names = "xusbxti";
-		};
+	xxti: clock-1 {
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+		#clock-cells = <0>;
+		clock-output-names = "xxti";
+	};
 
-		xxti: clock@1 {
-			compatible = "fixed-clock";
-			reg = <1>;
-			clock-frequency = <0>;
-			#clock-cells = <0>;
-			clock-output-names = "xxti";
-		};
+	xtcxo: clock-2 {
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+		#clock-cells = <0>;
+		clock-output-names = "xtcxo";
+	};
 
-		xtcxo: clock@2 {
-			compatible = "fixed-clock";
-			reg = <2>;
-			clock-frequency = <0>;
-			#clock-cells = <0>;
-			clock-output-names = "xtcxo";
+	bus_leftbus_opp_table: opp-table-0 {
+		compatible = "operating-points-v2";
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <900000>;
+		};
+		opp-80000000 {
+			opp-hz = /bits/ 64 <80000000>;
+			opp-microvolt = <900000>;
+		};
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp-134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
 		};
 	};
 
@@ -145,12 +321,12 @@
 			#size-cells = <1>;
 			ranges = <0 0x02020000 0x40000>;
 
-			smp-sysram@0 {
+			smp-sram@0 {
 				compatible = "samsung,exynos4210-sysram";
 				reg = <0x0 0x1000>;
 			};
 
-			smp-sysram@3f000 {
+			smp-sram@3f000 {
 				compatible = "samsung,exynos4210-sysram-ns";
 				reg = <0x3f000 0x1000>;
 			};
@@ -167,7 +343,7 @@
 		};
 
 		pmu_system_controller: system-controller@10020000 {
-			compatible = "samsung,exynos3250-pmu", "syscon";
+			compatible = "samsung,exynos3250-pmu", "simple-mfd", "syscon";
 			reg = <0x10020000 0x4000>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
@@ -175,45 +351,44 @@
 			clock-names = "clkout8";
 			clocks = <&cmu CLK_FIN_PLL>;
 			#clock-cells = <1>;
-		};
 
-		mipi_phy: video-phy {
-			compatible = "samsung,s5pv210-mipi-video-phy";
-			#phy-cells = <1>;
-			syscon = <&pmu_system_controller>;
+			mipi_phy: mipi-phy {
+				compatible = "samsung,s5pv210-mipi-video-phy";
+				#phy-cells = <1>;
+			};
 		};
 
 		pd_cam: power-domain@10023c00 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C00 0x20>;
+			reg = <0x10023c00 0x20>;
 			#power-domain-cells = <0>;
 			label = "CAM";
 		};
 
 		pd_mfc: power-domain@10023c40 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C40 0x20>;
+			reg = <0x10023c40 0x20>;
 			#power-domain-cells = <0>;
 			label = "MFC";
 		};
 
 		pd_g3d: power-domain@10023c60 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C60 0x20>;
+			reg = <0x10023c60 0x20>;
 			#power-domain-cells = <0>;
 			label = "G3D";
 		};
 
 		pd_lcd0: power-domain@10023c80 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C80 0x20>;
+			reg = <0x10023c80 0x20>;
 			#power-domain-cells = <0>;
 			label = "LCD0";
 		};
 
 		pd_isp: power-domain@10023ca0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023CA0 0x20>;
+			reg = <0x10023ca0 0x20>;
 			#power-domain-cells = <0>;
 			label = "ISP";
 		};
@@ -230,7 +405,7 @@
 
 		cmu_dmc: clock-controller@105c0000 {
 			compatible = "samsung,exynos3250-cmu-dmc";
-			reg = <0x105C0000 0x2000>;
+			reg = <0x105c0000 0x2000>;
 			#clock-cells = <1>;
 		};
 
@@ -245,7 +420,7 @@
 
 		tmu: tmu@100c0000 {
 			compatible = "samsung,exynos3250-tmu";
-			reg = <0x100C0000 0x100>;
+			reg = <0x100c0000 0x100>;
 			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_TMU_APBIF>;
 			clock-names = "tmu_apbif";
@@ -266,7 +441,8 @@
 		};
 
 		timer@10050000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos3250-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x10050000 0x800>;
 			interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
@@ -338,7 +514,7 @@
 
 		dsi_0: dsi@11c80000 {
 			compatible = "samsung,exynos3250-mipi-dsi";
-			reg = <0x11C80000 0x10000>;
+			reg = <0x11c80000 0x10000>;
 			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			samsung,phy-type = <0>;
 			power-domains = <&pd_lcd0>;
@@ -361,8 +537,8 @@
 			#iommu-cells = <0>;
 		};
 
-		hsotg: hsotg@12480000 {
-			compatible = "samsung,s3c6400-hsotg", "snps,dwc2";
+		hsotg: usb@12480000 {
+			compatible = "samsung,s3c6400-hsotg";
 			reg = <0x12480000 0x20000>;
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_USBOTG>;
@@ -372,7 +548,7 @@
 			status = "disabled";
 		};
 
-		mshc_0: mshc@12510000 {
+		mshc_0: mmc@12510000 {
 			compatible = "samsung,exynos5420-dw-mshc";
 			reg = <0x12510000 0x1000>;
 			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
@@ -384,7 +560,7 @@
 			status = "disabled";
 		};
 
-		mshc_1: mshc@12520000 {
+		mshc_1: mmc@12520000 {
 			compatible = "samsung,exynos5420-dw-mshc";
 			reg = <0x12520000 0x1000>;
 			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
@@ -396,7 +572,7 @@
 			status = "disabled";
 		};
 
-		mshc_2: mshc@12530000 {
+		mshc_2: mmc@12530000 {
 			compatible = "samsung,exynos5250-dw-mshc";
 			reg = <0x12530000 0x1000>;
 			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
@@ -408,9 +584,9 @@
 			status = "disabled";
 		};
 
-		exynos_usbphy: exynos-usbphy@125b0000 {
+		exynos_usbphy: usb-phy@125b0000 {
 			compatible = "samsung,exynos3250-usb2-phy";
-			reg = <0x125B0000 0x100>;
+			reg = <0x125b0000 0x100>;
 			samsung,pmureg-phandle = <&pmu_system_controller>;
 			clocks = <&cmu CLK_USBOTG>, <&cmu CLK_SCLK_UPLL>;
 			clock-names = "phy", "ref";
@@ -418,43 +594,31 @@
 			status = "disabled";
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			pdma0: pdma@12680000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x12680000 0x1000>;
-				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cmu CLK_PDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma0: dma-controller@12680000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12680000 0x1000>;
+			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_PDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			pdma1: pdma@12690000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x12690000 0x1000>;
-				interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cmu CLK_PDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma1: dma-controller@12690000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12690000 0x1000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_PDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
 		};
 
 		adc: adc@126c0000 {
 			compatible = "samsung,exynos3250-adc";
-			reg = <0x126C0000 0x100>;
+			reg = <0x126c0000 0x100>;
 			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "adc", "sclk";
 			clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>;
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 			samsung,syscon-phandle = <&pmu_system_controller>;
 			status = "disabled";
 		};
@@ -493,7 +657,7 @@
 		};
 
 		mfc: codec@13400000 {
-			compatible = "samsung,mfc-v7";
+			compatible = "samsung,exynos3250-mfc", "samsung,mfc-v7";
 			reg = <0x13400000 0x10000>;
 			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "mfc", "sclk_mfc";
@@ -601,7 +765,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138A0000 0x100>;
+			reg = <0x138a0000 0x100>;
 			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_I2C4>;
 			clock-names = "i2c";
@@ -614,7 +778,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138B0000 0x100>;
+			reg = <0x138b0000 0x100>;
 			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_I2C5>;
 			clock-names = "i2c";
@@ -627,7 +791,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138C0000 0x100>;
+			reg = <0x138c0000 0x100>;
 			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_I2C6>;
 			clock-names = "i2c";
@@ -640,7 +804,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138D0000 0x100>;
+			reg = <0x138d0000 0x100>;
 			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_I2C7>;
 			clock-names = "i2c";
@@ -696,7 +860,7 @@
 
 		pwm: pwm@139d0000 {
 			compatible = "samsung,exynos4210-pwm";
-			reg = <0x139D0000 0x1000>;
+			reg = <0x139d0000 0x1000>;
 			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
@@ -706,25 +870,25 @@
 			status = "disabled";
 		};
 
-		ppmu_dmc0: ppmu_dmc0@106a0000 {
+		ppmu_dmc0: ppmu@106a0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x106a0000 0x2000>;
 			status = "disabled";
 		};
 
-		ppmu_dmc1: ppmu_dmc1@106b0000 {
+		ppmu_dmc1: ppmu@106b0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x106b0000 0x2000>;
 			status = "disabled";
 		};
 
-		ppmu_cpu: ppmu_cpu@106c0000 {
+		ppmu_cpu: ppmu@106c0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x106c0000 0x2000>;
 			status = "disabled";
 		};
 
-		ppmu_rightbus: ppmu_rightbus@112a0000 {
+		ppmu_rightbus: ppmu@112a0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x112a0000 0x2000>;
 			clocks = <&cmu CLK_PPMURIGHT>;
@@ -732,7 +896,7 @@
 			status = "disabled";
 		};
 
-		ppmu_leftbus: ppmu_leftbus0@116a0000 {
+		ppmu_leftbus: ppmu@116a0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x116a0000 0x2000>;
 			clocks = <&cmu CLK_PPMULEFT>;
@@ -740,7 +904,7 @@
 			status = "disabled";
 		};
 
-		ppmu_camif: ppmu_camif@11ac0000 {
+		ppmu_camif: ppmu@11ac0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x11ac0000 0x2000>;
 			clocks = <&cmu CLK_PPMUCAMIF>;
@@ -748,7 +912,7 @@
 			status = "disabled";
 		};
 
-		ppmu_lcd0: ppmu_lcd0@11e40000 {
+		ppmu_lcd0: ppmu@11e40000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x11e40000 0x2000>;
 			clocks = <&cmu CLK_PPMULCD0>;
@@ -756,7 +920,7 @@
 			status = "disabled";
 		};
 
-		ppmu_fsys: ppmu_fsys@12630000 {
+		ppmu_fsys: ppmu@12630000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x12630000 0x2000>;
 			clocks = <&cmu CLK_PPMUFILE>;
@@ -764,7 +928,7 @@
 			status = "disabled";
 		};
 
-		ppmu_g3d: ppmu_g3d@13220000 {
+		ppmu_g3d: ppmu@13220000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x13220000 0x2000>;
 			clocks = <&cmu CLK_PPMUG3D>;
@@ -772,194 +936,13 @@
 			status = "disabled";
 		};
 
-		ppmu_mfc: ppmu_mfc@13660000 {
+		ppmu_mfc: ppmu@13660000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x13660000 0x2000>;
 			clocks = <&cmu CLK_PPMUMFC_L>;
 			clock-names = "ppmu";
 			status = "disabled";
 		};
-
-		bus_dmc: bus_dmc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu_dmc CLK_DIV_DMC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_dmc_opp_table>;
-			status = "disabled";
-		};
-
-		bus_dmc_opp_table: opp_table1 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-				opp-microvolt = <800000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-				opp-microvolt = <800000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-				opp-microvolt = <800000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-				opp-microvolt = <825000>;
-			};
-			opp-400000000 {
-				opp-hz = /bits/ 64 <400000000>;
-				opp-microvolt = <875000>;
-			};
-		};
-
-		bus_leftbus: bus_leftbus {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_GDL>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_rightbus: bus_rightbus {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_GDR>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_lcd0: bus_lcd0 {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_ACLK_160>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_fsys: bus_fsys {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_ACLK_200>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_mcuisp: bus_mcuisp {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_mcuisp_opp_table>;
-			status = "disabled";
-		};
-
-		bus_isp: bus_isp {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_ACLK_266>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_isp_opp_table>;
-			status = "disabled";
-		};
-
-		bus_peril: bus_peril {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_DIV_ACLK_100>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_peril_opp_table>;
-			status = "disabled";
-		};
-
-		bus_mfc: bus_mfc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&cmu CLK_SCLK_MFC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_leftbus_opp_table: opp_table2 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-				opp-microvolt = <900000>;
-			};
-			opp-80000000 {
-				opp-hz = /bits/ 64 <80000000>;
-				opp-microvolt = <900000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-				opp-microvolt = <1000000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-				opp-microvolt = <1000000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-				opp-microvolt = <1000000>;
-			};
-		};
-
-		bus_mcuisp_opp_table: opp_table3 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-			};
-			opp-80000000 {
-				opp-hz = /bits/ 64 <80000000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-			opp-400000000 {
-				opp-hz = /bits/ 64 <400000000>;
-			};
-		};
-
-		bus_isp_opp_table: opp_table4 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-			};
-			opp-80000000 {
-				opp-hz = /bits/ 64 <80000000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-			opp-300000000 {
-				opp-hz = /bits/ 64 <300000000>;
-			};
-		};
-
-		bus_peril_opp_table: opp_table5 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-			};
-			opp-80000000 {
-				opp-hz = /bits/ 64 <80000000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/exynos4-cpu-thermal.dtsi b/arch/arm/boot/dts/samsung/exynos4-cpu-thermal.dtsi
index 021d9fc1b492..27a1a8952665 100644
--- a/arch/arm/boot/dts/exynos4-cpu-thermal.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4-cpu-thermal.dtsi
@@ -10,7 +10,7 @@
 / {
 thermal-zones {
 	cpu_thermal: cpu-thermal {
-		thermal-sensors = <&tmu 0>;
+		thermal-sensors = <&tmu>;
 		polling-delay-passive = <0>;
 		polling-delay = <0>;
 		trips {
diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/samsung/exynos4.dtsi
index d2779a790ce3..7f981b5c0d64 100644
--- a/arch/arm/boot/dts/exynos4.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4.dtsi
@@ -9,7 +9,7 @@
  *
  * Samsung's Exynos4 SoC series device nodes are listed in this file.  Particular
  * SoCs from Exynos4 series can include this file and provide values for SoCs
- * specfic bindings.
+ * specific bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
  * Exynos4 SoCs. As device tree coverage for Exynos4 increases, additional
@@ -65,7 +65,7 @@
 
 		clock_audss: clock-controller@3810000 {
 			compatible = "samsung,exynos4210-audss-clock";
-			reg = <0x03810000 0x0C>;
+			reg = <0x03810000 0x0c>;
 			#clock-cells = <1>;
 			clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
 				 <&clock CLK_SCLK_AUDIO0>,
@@ -105,36 +105,30 @@
 			reg = <0x12570000 0x14>;
 		};
 
-		mipi_phy: video-phy {
-			compatible = "samsung,s5pv210-mipi-video-phy";
-			#phy-cells = <1>;
-			syscon = <&pmu_system_controller>;
-		};
-
 		pd_mfc: power-domain@10023c40 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C40 0x20>;
+			reg = <0x10023c40 0x20>;
 			#power-domain-cells = <0>;
 			label = "MFC";
 		};
 
 		pd_g3d: power-domain@10023c60 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C60 0x20>;
+			reg = <0x10023c60 0x20>;
 			#power-domain-cells = <0>;
 			label = "G3D";
 		};
 
 		pd_lcd0: power-domain@10023c80 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C80 0x20>;
+			reg = <0x10023c80 0x20>;
 			#power-domain-cells = <0>;
 			label = "LCD0";
 		};
 
 		pd_tv: power-domain@10023c20 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C20 0x20>;
+			reg = <0x10023c20 0x20>;
 			#power-domain-cells = <0>;
 			power-domains = <&pd_lcd0>;
 			label = "TV";
@@ -142,21 +136,21 @@
 
 		pd_cam: power-domain@10023c00 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023C00 0x20>;
+			reg = <0x10023c00 0x20>;
 			#power-domain-cells = <0>;
 			label = "CAM";
 		};
 
 		pd_gps: power-domain@10023ce0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023CE0 0x20>;
+			reg = <0x10023ce0 0x20>;
 			#power-domain-cells = <0>;
 			label = "GPS";
 		};
 
 		pd_gps_alive: power-domain@10023d00 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023D00 0x20>;
+			reg = <0x10023d00 0x20>;
 			#power-domain-cells = <0>;
 			label = "GPS alive";
 		};
@@ -181,16 +175,21 @@
 		};
 
 		pmu_system_controller: system-controller@10020000 {
-			compatible = "samsung,exynos4210-pmu", "syscon";
+			compatible = "samsung,exynos4210-pmu", "simple-mfd", "syscon";
 			reg = <0x10020000 0x4000>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			interrupt-parent = <&gic>;
+
+			mipi_phy: mipi-phy {
+				compatible = "samsung,s5pv210-mipi-video-phy";
+				#phy-cells = <1>;
+			};
 		};
 
 		dsi_0: dsi@11c80000 {
 			compatible = "samsung,exynos4210-mipi-dsi";
-			reg = <0x11C80000 0x10000>;
+			reg = <0x11c80000 0x10000>;
 			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 			power-domains = <&pd_lcd0>;
 			phys = <&mipi_phy 1>;
@@ -202,18 +201,18 @@
 			#size-cells = <0>;
 		};
 
-		camera: camera {
-			compatible = "samsung,fimc", "simple-bus";
+		camera: camera@11800000 {
+			compatible = "samsung,fimc";
+			ranges = <0x0 0x11800000 0xa0000>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			#clock-cells = <1>;
 			clock-output-names = "cam_a_clkout", "cam_b_clkout";
-			ranges;
 
-			fimc_0: fimc@11800000 {
+			fimc_0: fimc@0 {
 				compatible = "samsung,exynos4210-fimc";
-				reg = <0x11800000 0x1000>;
+				reg = <0x0 0x1000>;
 				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clock CLK_FIMC0>,
 					 <&clock CLK_SCLK_FIMC0>;
@@ -224,9 +223,9 @@
 				status = "disabled";
 			};
 
-			fimc_1: fimc@11810000 {
+			fimc_1: fimc@10000 {
 				compatible = "samsung,exynos4210-fimc";
-				reg = <0x11810000 0x1000>;
+				reg = <0x00010000 0x1000>;
 				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clock CLK_FIMC1>,
 					 <&clock CLK_SCLK_FIMC1>;
@@ -237,9 +236,9 @@
 				status = "disabled";
 			};
 
-			fimc_2: fimc@11820000 {
+			fimc_2: fimc@20000 {
 				compatible = "samsung,exynos4210-fimc";
-				reg = <0x11820000 0x1000>;
+				reg = <0x00020000 0x1000>;
 				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clock CLK_FIMC2>,
 					 <&clock CLK_SCLK_FIMC2>;
@@ -250,9 +249,9 @@
 				status = "disabled";
 			};
 
-			fimc_3: fimc@11830000 {
+			fimc_3: fimc@30000 {
 				compatible = "samsung,exynos4210-fimc";
-				reg = <0x11830000 0x1000>;
+				reg = <0x00030000 0x1000>;
 				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clock CLK_FIMC3>,
 					 <&clock CLK_SCLK_FIMC3>;
@@ -263,9 +262,9 @@
 				status = "disabled";
 			};
 
-			csis_0: csis@11880000 {
+			csis_0: csis@80000 {
 				compatible = "samsung,exynos4210-csis";
-				reg = <0x11880000 0x4000>;
+				reg = <0x00080000 0x4000>;
 				interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clock CLK_CSIS0>,
 					 <&clock CLK_SCLK_CSIS0>;
@@ -279,9 +278,9 @@
 				#size-cells = <0>;
 			};
 
-			csis_1: csis@11890000 {
+			csis_1: csis@90000 {
 				compatible = "samsung,exynos4210-csis";
-				reg = <0x11890000 0x4000>;
+				reg = <0x00090000 0x4000>;
 				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clock CLK_CSIS1>,
 					 <&clock CLK_SCLK_CSIS1>;
@@ -309,14 +308,14 @@
 
 		keypad: keypad@100a0000 {
 			compatible = "samsung,s5pv210-keypad";
-			reg = <0x100A0000 0x100>;
+			reg = <0x100a0000 0x100>;
 			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_KEYIF>;
 			clock-names = "keypad";
 			status = "disabled";
 		};
 
-		sdhci_0: sdhci@12510000 {
+		sdhci_0: mmc@12510000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12510000 0x100>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -325,7 +324,7 @@
 			status = "disabled";
 		};
 
-		sdhci_1: sdhci@12520000 {
+		sdhci_1: mmc@12520000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12520000 0x100>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -334,7 +333,7 @@
 			status = "disabled";
 		};
 
-		sdhci_2: sdhci@12530000 {
+		sdhci_2: mmc@12530000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12530000 0x100>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -343,7 +342,7 @@
 			status = "disabled";
 		};
 
-		sdhci_3: sdhci@12540000 {
+		sdhci_3: mmc@12540000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12540000 0x100>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -352,9 +351,9 @@
 			status = "disabled";
 		};
 
-		exynos_usbphy: exynos-usbphy@125b0000 {
+		exynos_usbphy: usb-phy@125b0000 {
 			compatible = "samsung,exynos4210-usb2-phy";
-			reg = <0x125B0000 0x100>;
+			reg = <0x125b0000 0x100>;
 			samsung,pmureg-phandle = <&pmu_system_controller>;
 			clocks = <&clock CLK_USB_DEVICE>, <&clock CLK_XUSBXTI>;
 			clock-names = "phy", "ref";
@@ -362,7 +361,7 @@
 			status = "disabled";
 		};
 
-		hsotg: hsotg@12480000 {
+		hsotg: usb@12480000 {
 			compatible = "samsung,s3c6400-hsotg";
 			reg = <0x12480000 0x20000>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
@@ -373,7 +372,7 @@
 			status = "disabled";
 		};
 
-		ehci: ehci@12580000 {
+		ehci: usb@12580000 {
 			compatible = "samsung,exynos4210-ehci";
 			reg = <0x12580000 0x100>;
 			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
@@ -384,7 +383,7 @@
 			phy-names = "host", "hsic0", "hsic1";
 		};
 
-		ohci: ohci@12590000 {
+		ohci: usb@12590000 {
 			compatible = "samsung,exynos4210-ohci";
 			reg = <0x12590000 0x100>;
 			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
@@ -546,7 +545,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138A0000 0x100>;
+			reg = <0x138a0000 0x100>;
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_I2C4>;
 			clock-names = "i2c";
@@ -559,7 +558,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138B0000 0x100>;
+			reg = <0x138b0000 0x100>;
 			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_I2C5>;
 			clock-names = "i2c";
@@ -572,7 +571,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138C0000 0x100>;
+			reg = <0x138c0000 0x100>;
 			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_I2C6>;
 			clock-names = "i2c";
@@ -585,7 +584,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x138D0000 0x100>;
+			reg = <0x138d0000 0x100>;
 			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_I2C7>;
 			clock-names = "i2c";
@@ -598,14 +597,14 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "samsung,s3c2440-hdmiphy-i2c";
-			reg = <0x138E0000 0x100>;
+			reg = <0x138e0000 0x100>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_I2C_HDMI>;
 			clock-names = "i2c";
 			status = "disabled";
 
-			hdmi_i2c_phy: hdmiphy@38 {
-				compatible = "exynos4210-hdmiphy";
+			hdmi_i2c_phy: hdmi-phy@38 {
+				compatible = "samsung,exynos4210-hdmiphy";
 				reg = <0x38>;
 			};
 		};
@@ -657,7 +656,7 @@
 
 		pwm: pwm@139d0000 {
 			compatible = "samsung,exynos4210-pwm";
-			reg = <0x139D0000 0x1000>;
+			reg = <0x139d0000 0x1000>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
@@ -669,45 +668,31 @@
 			status = "disabled";
 		};
 
-		amba: amba {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			interrupt-parent = <&gic>;
-			ranges;
-
-			pdma0: pdma@12680000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x12680000 0x1000>;
-				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma0: dma-controller@12680000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12680000 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			pdma1: pdma@12690000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x12690000 0x1000>;
-				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma1: dma-controller@12690000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12690000 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			mdma1: mdma@12850000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x12850000 0x1000>;
-				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_MDMA>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <1>;
-			};
+		mdma1: dma-controller@12850000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12850000 0x1000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_MDMA>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
 		};
 
 		fimd: fimd@11c00000 {
@@ -726,7 +711,7 @@
 
 		tmu: tmu@100c0000 {
 			interrupt-parent = <&combiner>;
-			reg = <0x100C0000 0x100>;
+			reg = <0x100c0000 0x100>;
 			interrupts = <2 4>;
 			status = "disabled";
 			#thermal-sensor-cells = <0>;
@@ -753,7 +738,7 @@
 
 		hdmi: hdmi@12d00000 {
 			compatible = "samsung,exynos4210-hdmi";
-			reg = <0x12D00000 0x70000>;
+			reg = <0x12d00000 0x70000>;
 			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
 				      "sclk_hdmiphy", "mout_hdmi";
@@ -770,7 +755,7 @@
 
 		hdmicec: cec@100b0000 {
 			compatible = "samsung,s5p-cec";
-			reg = <0x100B0000 0x200>;
+			reg = <0x100b0000 0x200>;
 			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_HDMI_CEC>;
 			clock-names = "hdmicec";
@@ -784,13 +769,13 @@
 		mixer: mixer@12c10000 {
 			compatible = "samsung,exynos4210-mixer";
 			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			reg = <0x12C10000 0x2100>, <0x12c00000 0x300>;
+			reg = <0x12c10000 0x2100>, <0x12c00000 0x300>;
 			power-domains = <&pd_tv>;
 			iommus = <&sysmmu_tv>;
 			status = "disabled";
 		};
 
-		ppmu_dmc0: ppmu_dmc0@106a0000 {
+		ppmu_dmc0: ppmu@106a0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x106a0000 0x2000>;
 			clocks = <&clock CLK_PPMUDMC0>;
@@ -798,7 +783,7 @@
 			status = "disabled";
 		};
 
-		ppmu_dmc1: ppmu_dmc1@106b0000 {
+		ppmu_dmc1: ppmu@106b0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x106b0000 0x2000>;
 			clocks = <&clock CLK_PPMUDMC1>;
@@ -806,7 +791,7 @@
 			status = "disabled";
 		};
 
-		ppmu_cpu: ppmu_cpu@106c0000 {
+		ppmu_cpu: ppmu@106c0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x106c0000 0x2000>;
 			clocks = <&clock CLK_PPMUCPU>;
@@ -814,7 +799,7 @@
 			status = "disabled";
 		};
 
-		ppmu_rightbus: ppmu_rightbus@112a0000 {
+		ppmu_rightbus: ppmu@112a0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x112a0000 0x2000>;
 			clocks = <&clock CLK_PPMURIGHT>;
@@ -822,7 +807,7 @@
 			status = "disabled";
 		};
 
-		ppmu_leftbus: ppmu_leftbus0@116a0000 {
+		ppmu_leftbus: ppmu@116a0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x116a0000 0x2000>;
 			clocks = <&clock CLK_PPMULEFT>;
@@ -830,7 +815,7 @@
 			status = "disabled";
 		};
 
-		ppmu_camif: ppmu_camif@11ac0000 {
+		ppmu_camif: ppmu@11ac0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x11ac0000 0x2000>;
 			clocks = <&clock CLK_PPMUCAMIF>;
@@ -838,7 +823,7 @@
 			status = "disabled";
 		};
 
-		ppmu_lcd0: ppmu_lcd0@11e40000 {
+		ppmu_lcd0: ppmu@11e40000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x11e40000 0x2000>;
 			clocks = <&clock CLK_PPMULCD0>;
@@ -846,13 +831,13 @@
 			status = "disabled";
 		};
 
-		ppmu_fsys: ppmu_g3d@12630000 {
+		ppmu_fsys: ppmu@12630000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x12630000 0x2000>;
 			status = "disabled";
 		};
 
-		ppmu_image: ppmu_image@12aa0000 {
+		ppmu_image: ppmu@12aa0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x12aa0000 0x2000>;
 			clocks = <&clock CLK_PPMUIMAGE>;
@@ -860,7 +845,7 @@
 			status = "disabled";
 		};
 
-		ppmu_tv: ppmu_tv@12e40000 {
+		ppmu_tv: ppmu@12e40000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x12e40000 0x2000>;
 			clocks = <&clock CLK_PPMUTV>;
@@ -868,7 +853,7 @@
 			status = "disabled";
 		};
 
-		ppmu_g3d: ppmu_g3d@13220000 {
+		ppmu_g3d: ppmu@13220000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x13220000 0x2000>;
 			clocks = <&clock CLK_PPMUG3D>;
@@ -876,7 +861,7 @@
 			status = "disabled";
 		};
 
-		ppmu_mfc_left: ppmu_mfc_left@13660000 {
+		ppmu_mfc_left: ppmu@13660000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x13660000 0x2000>;
 			clocks = <&clock CLK_PPMUMFC_L>;
@@ -884,7 +869,7 @@
 			status = "disabled";
 		};
 
-		ppmu_mfc_right: ppmu_mfc_right@13670000 {
+		ppmu_mfc_right: ppmu@13670000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x13670000 0x2000>;
 			clocks = <&clock CLK_PPMUMFC_R>;
@@ -916,7 +901,7 @@
 
 		sysmmu_tv: sysmmu@12e20000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x12E20000 0x1000>;
+			reg = <0x12e20000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <5 4>;
 			clock-names = "sysmmu", "master";
@@ -927,7 +912,7 @@
 
 		sysmmu_fimc0: sysmmu@11a20000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11A20000 0x1000>;
+			reg = <0x11a20000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 2>;
 			clock-names = "sysmmu", "master";
@@ -938,7 +923,7 @@
 
 		sysmmu_fimc1: sysmmu@11a30000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11A30000 0x1000>;
+			reg = <0x11a30000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 3>;
 			clock-names = "sysmmu", "master";
@@ -949,7 +934,7 @@
 
 		sysmmu_fimc2: sysmmu@11a40000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11A40000 0x1000>;
+			reg = <0x11a40000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 4>;
 			clock-names = "sysmmu", "master";
@@ -960,7 +945,7 @@
 
 		sysmmu_fimc3: sysmmu@11a50000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11A50000 0x1000>;
+			reg = <0x11a50000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 5>;
 			clock-names = "sysmmu", "master";
@@ -971,7 +956,7 @@
 
 		sysmmu_jpeg: sysmmu@11a60000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11A60000 0x1000>;
+			reg = <0x11a60000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 6>;
 			clock-names = "sysmmu", "master";
@@ -982,7 +967,7 @@
 
 		sysmmu_rotator: sysmmu@12a30000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x12A30000 0x1000>;
+			reg = <0x12a30000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <5 0>;
 			clock-names = "sysmmu", "master";
@@ -993,7 +978,7 @@
 
 		sysmmu_fimd0: sysmmu@11e20000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11E20000 0x1000>;
+			reg = <0x11e20000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <5 2>;
 			clock-names = "sysmmu", "master";
diff --git a/arch/arm/boot/dts/samsung/exynos4210-i9100.dts b/arch/arm/boot/dts/samsung/exynos4210-i9100.dts
new file mode 100644
index 000000000000..0d8495792a70
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4210-i9100.dts
@@ -0,0 +1,906 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4210 based Galaxy S2 (GT-I9100 version) device tree
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2020 Stenkin Evgeniy <stenkinevgeniy@gmail.com>
+ * Copyright (c) 2020 Paul Cercueil <paul@crapouillou.net>
+ */
+
+/dts-v1/;
+#include "exynos4210.dtsi"
+#include "exynos4412-ppmu-common.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	model = "Samsung Galaxy S2 (GT-I9100)";
+	compatible = "samsung,i9100", "samsung,exynos4210", "samsung,exynos4";
+	chassis-type = "handset";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x40000000>;
+	};
+
+	aliases {
+		mmc0 = &sdhci_0;
+		mmc1 = &sdhci_2;
+		mmc2 = &sdhci_3;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	vemmc_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VMEM_VDD_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tsp_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_FIXED_VOLTAGES";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	cam_af_28v_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "8M_AF_2.8V_EN";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	cam_io_en_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "CAM_IO_EN";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	cam_io_12v_reg: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "8M_1.2V_EN";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vt_core_15v_reg: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "VT_CORE_1.5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-vol-down {
+			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		key-vol-up {
+			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		key-power {
+			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		key-ok {
+			gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_OK>;
+			label = "ok";
+			debounce-interval = <10>;
+		};
+	};
+
+	wlan_pwrseq: sdhci3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpl1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	i2c_max17042_fuel: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sda-gpios = <&gpy4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <5>;
+
+		battery@36 {
+			compatible = "maxim,max17042";
+
+			interrupt-parent = <&gpx2>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+			pinctrl-0 = <&max17042_fuel_irq>;
+			pinctrl-names = "default";
+
+			reg = <0x36>;
+			maxim,over-heat-temp = <700>;
+			maxim,over-volt = <4500>;
+		};
+	};
+
+	i2c_s5k5baf: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sda-gpios = <&gpc1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpc1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+
+		image-sensor@2d {
+			compatible = "samsung,s5k5baf";
+			reg = <0x2d>;
+			vdda-supply = <&cam_io_en_reg>;
+			vddreg-supply = <&vt_core_15v_reg>;
+			vddio-supply = <&vtcam_reg>;
+			clocks = <&camera 0>;
+			clock-names = "mclk";
+			stbyn-gpios = <&gpl2 0 GPIO_ACTIVE_LOW>;
+			rstn-gpios = <&gpl2 1 GPIO_ACTIVE_LOW>;
+			clock-frequency = <24000000>;
+
+			port {
+				s5k5bafx_ep: endpoint {
+					remote-endpoint = <&csis1_ep>;
+					data-lanes = <1>;
+				};
+			};
+		};
+	};
+
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sda-gpios = <&gpk1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpk1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+
+		touchscreen@20 {
+			compatible = "cypress,aries-touchkey";
+			reg = <0x20>;
+
+			interrupt-parent = <&gpl0>;
+			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+
+			vdd-supply = <&vtouchled_reg>;
+			vcc-supply = <&vtouch_reg>;
+			linux,keycodes = <KEY_MENU>, <KEY_BACK>;
+		};
+	};
+
+	spi-3 {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		num-chipselects = <1>;
+		cs-gpios = <&gpy4 3 GPIO_ACTIVE_LOW>;
+		sck-gpios = <&gpy3 1 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpy3 3 GPIO_ACTIVE_HIGH>;
+
+		lcd@0 {
+			compatible = "samsung,ld9040";
+			reg = <0>;
+
+			spi-max-frequency = <1200000>;
+
+			vdd3-supply = <&vmipi_reg>;
+			vci-supply = <&vcclcd_reg>;
+
+			reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
+			power-on-delay = <10>;
+			reset-delay = <10>;
+
+			panel-width-mm = <56>;
+			panel-height-mm = <93>;
+
+			display-timings {
+				timing {
+					clock-frequency = <23492370>;
+					hactive = <480>;
+					vactive = <800>;
+					hback-porch = <16>;
+					hfront-porch = <16>;
+					vback-porch = <2>;
+					vfront-porch = <28>;
+					hsync-len = <2>;
+					vsync-len = <1>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+					de-active = <0>;
+					pixelclk-active = <0>;
+				};
+			};
+
+			port {
+				lcd_ep: endpoint {
+					remote-endpoint = <&fimd_dpi_ep>;
+				};
+			};
+		};
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti";
+			clock-frequency = <0>;
+		};
+
+		xusbxti {
+			compatible = "samsung,clock-xusbxti";
+			clock-frequency = <24000000>;
+		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on max8997 PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&camera {
+	pinctrl-0 = <&cam_port_a_clk_active>;
+	pinctrl-names = "default";
+	status = "okay";
+	assigned-clocks = <&clock CLK_MOUT_CAM0>, <&clock CLK_MOUT_CAM1>;
+	assigned-clock-parents = <&clock CLK_XUSBXTI>, <&clock CLK_XUSBXTI>;
+};
+
+&csis_1 {
+	status = "okay";
+	vddcore-supply = <&vusb_reg>;
+	vddio-supply = <&vmipi_reg>;
+	clock-frequency = <160000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@4 {
+		reg = <4>;
+		csis1_ep: endpoint {
+			remote-endpoint = <&s5k5bafx_ep>;
+			data-lanes = <1>;
+			samsung,csis-hs-settle = <6>;
+		};
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&varm_breg>;
+};
+
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz */
+			cooling-device = <&cpu0 2 2>;
+		};
+		map1 {
+			/* Corresponds to 200MHz */
+			cooling-device = <&cpu0 4 4>;
+		};
+	};
+};
+
+&ehci {
+	status = "okay";
+
+	phys = <&exynos_usbphy 1>;
+	phy-names = "host";
+};
+
+&exynos_usbphy {
+	status = "okay";
+
+	vbus-supply = <&safe1_sreg>;
+};
+
+&fimc_0 {
+	status = "okay";
+
+	assigned-clocks = <&clock CLK_MOUT_FIMC0>, <&clock CLK_SCLK_FIMC0>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimc_1 {
+	/* Back camera not implemented */
+	status = "disabled";
+
+	assigned-clocks = <&clock CLK_MOUT_FIMC1>, <&clock CLK_SCLK_FIMC1>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimc_2 {
+	status = "okay";
+
+	assigned-clocks = <&clock CLK_MOUT_FIMC2>, <&clock CLK_SCLK_FIMC2>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimc_3 {
+	/* Back camera not implemented */
+	status = "disabled";
+
+	assigned-clocks = <&clock CLK_MOUT_FIMC3>, <&clock CLK_SCLK_FIMC3>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimd {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	samsung,invert-vden;
+	samsung,invert-vclk;
+
+	pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
+	pinctrl-names = "default";
+
+	port@3 {
+		reg = <3>;
+
+		fimd_dpi_ep: endpoint {
+			remote-endpoint = <&lcd_ep>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+
+	mali-supply = <&vg3d_breg>;
+};
+
+&hsotg {
+	status = "okay";
+
+	dr_mode = "otg";
+	vusb_d-supply = <&vusb_reg>;
+	vusb_a-supply = <&vusbdac_reg>;
+};
+
+&i2c_1 {
+	status = "okay";
+
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+
+	lis3dh: accelerometer@19 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x19>;
+
+		mount-matrix = "0", "-1", "0",
+			       "1", "0", "0",
+			       "0", "0", "1";
+	};
+};
+
+&i2c_3 {
+	status = "okay";
+
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+
+	pinctrl-0 = <&i2c3_bus>;
+	pinctrl-names = "default";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+
+		interrupt-parent = <&gpx0>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&i2c_5 {
+	status = "okay";
+
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+
+	pinctrl-0 = <&i2c5_bus>;
+	pinctrl-names = "default";
+
+	pmic@66 {
+		compatible = "maxim,max8997-pmic";
+		reg = <0x66>;
+
+		interrupts-extended = <&gpx0 7 IRQ_TYPE_NONE>,
+				      <&gpx2 3 IRQ_TYPE_EDGE_FALLING>;
+
+		max8997,pmic-buck1-uses-gpio-dvs;
+		max8997,pmic-buck2-uses-gpio-dvs;
+		max8997,pmic-buck5-uses-gpio-dvs;
+
+		max8997,pmic-ignore-gpiodvs-side-effect;
+		max8997,pmic-buck125-default-dvs-idx = <0>;
+
+		max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>,
+						 <&gpx0 6 GPIO_ACTIVE_HIGH>,
+						 <&gpl0 0 GPIO_ACTIVE_HIGH>;
+
+		max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
+
+		max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
+						 <950000>,  <900000>,
+						 <1100000>, <1000000>,
+						 <950000>,  <900000>;
+
+		max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
+
+		pinctrl-0 = <&max8997_irq>, <&otg_gp>, <&usb_sel>;
+		pinctrl-names = "default";
+
+		charger-supply = <&charger_reg>;
+
+		regulators {
+			vadc_reg: LDO1 {
+				regulator-name = "VADC_3.3V_C210";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+
+			};
+			valive_reg: LDO2 {
+				regulator-name = "VALIVE_1.1V_C210";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+
+			};
+
+			vusb_reg: LDO3 {
+				regulator-name = "VUSB_1.1V_C210";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			vmipi_reg: LDO4 {
+				regulator-name = "VMIPI_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vhsic_reg: LDO5 {
+				regulator-name = "VHSIC_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vpda_reg: LDO6 {
+				regulator-name = "VCC_1.8V_PDA";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcam_reg: LDO7 {
+				regulator-name = "CAM_ISP_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vusbdac_reg: LDO8 {
+				regulator-name = "VUSB+VDAC_3.3V_C210";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vccpda_reg: LDO9 {
+				regulator-name = "VCC_2.8V_PDA";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			vtouch_reg: LDO11 {
+				regulator-name = "TOUCH_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vpll_reg: LDO10 {
+				regulator-name = "VPLL_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vtcam_reg: LDO12 {
+				regulator-name = "VT_CAM_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				/*
+				 * Force-enable this regulator; otherwise the
+				 * kernel hangs very early in the boot process
+				 * for about 12 seconds, without apparent
+				 * reason.
+				 */
+				regulator-always-on;
+			};
+
+			vcclcd_reg: LDO13 {
+				regulator-name = "VCC_3.0V_LCD";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vmotor_reg: LDO14 {
+				regulator-name = "VCC_2.8V_MOTOR";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vled_reg: LDO15 {
+				regulator-name = "LED_A_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			camsensor_reg: LDO16 {
+				regulator-name = "CAM_SENSOR_IO_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vtf_reg: LDO17 {
+				regulator-name = "VTF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vtouchled_reg: LDO18 {
+				regulator-name = "TOUCH_LED_3.3V";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vddq_reg: LDO21 {
+				regulator-name = "VDDQ_M1M2_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			varm_breg: BUCK1 {
+				regulator-name = "VARM_1.2V_C210";
+				regulator-min-microvolt = <65000>;
+				regulator-max-microvolt = <2225000>;
+				regulator-always-on;
+			};
+
+			vint_breg: BUCK2 {
+				regulator-name = "VINT_1.1V_C210";
+				regulator-min-microvolt = <65000>;
+				regulator-max-microvolt = <2225000>;
+				regulator-always-on;
+			};
+
+			vg3d_breg: BUCK3 {
+				regulator-name = "G3D_1.1V";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-microvolt-offset = <50000>;
+				regulator-always-on;
+			};
+
+			camisp_breg: BUCK4 {
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vmem_breg: BUCK5 {
+				regulator-name = "VMEM_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vccsub_breg: BUCK7 {
+				regulator-name = "VCC_SUB_2.0V";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			safe1_sreg: ESAFEOUT1 {
+				regulator-name = "SAFEOUT1";
+			};
+
+			safe2_sreg: ESAFEOUT2 {
+				regulator-name = "SAFEOUT2";
+				regulator-boot-on;
+			};
+
+			EN32KHZ_AP {
+				regulator-name = "EN32KHZ_AP";
+				regulator-always-on;
+			};
+
+			EN32KHZ_CP {
+				regulator-name = "EN32KHZ_CP";
+				regulator-always-on;
+			};
+
+			charger_reg: CHARGER {
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <200000>;
+				regulator-max-microamp = <950000>;
+			};
+
+			chargercv_reg: CHARGER_CV {
+				regulator-name = "CHARGER_CV";
+				regulator-min-microvolt = <4200000>;
+				regulator-max-microvolt = <4200000>;
+				regulator-always-on;
+			};
+
+			CHARGER_TOPOFF {
+				regulator-name = "CHARGER_TOPOFF";
+				regulator-min-microamp = <200000>;
+				regulator-max-microamp = <200000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c_7 {
+	status = "okay";
+
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <400000>;
+
+	pinctrl-0 = <&i2c7_bus>;
+	pinctrl-names = "default";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0c>;
+
+		gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pinctrl_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep0>;
+
+	sleep0: sleep-state {
+		gpa0-0-pin {
+			samsung,pins = "gpa0-0";
+			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>;
+			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
+		};
+
+		gpa0-1-pin {
+			samsung,pins = "gpa0-1";
+			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT0>;
+			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
+		};
+
+		gpa0-2-pin {
+			samsung,pins = "gpa0-2";
+			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>;
+			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
+		};
+
+		gpa0-3-pin {
+			samsung,pins = "gpa0-3";
+			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
+		};
+	};
+};
+
+&pinctrl_1 {
+	mhl_int: mhl-int-pins {
+		samsung,pins = "gpf3-5";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	i2c_mhl_bus: i2c-mhl-bus-pins {
+		samsung,pins = "gpf0-4", "gpf0-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	usb_sel: usb-sel-pins {
+		samsung,pins = "gpl0-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-val = <0>;
+	};
+
+	bt_en: bt-en-pins {
+		samsung,pins = "gpl0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-val = <0>;
+	};
+
+	bt_res: bt-res-pins {
+		samsung,pins = "gpl1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-val = <0>;
+	};
+
+	otg_gp: otg-gp-pins {
+		samsung,pins = "gpx3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-val = <0>;
+	};
+
+	mag_mhl_gpio: mag-mhl-pins {
+		samsung,pins = "gpd0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	max8997_irq: max8997-irq-pins {
+		samsung,pins = "gpx0-7";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	max17042_fuel_irq: max17042-fuel-irq-pins {
+		samsung,pins = "gpx2-3";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp224_irq: tsp224-irq-pins {
+		samsung,pins = "gpx0-4";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+	};
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&sdhci_0 {
+	status = "okay";
+
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&vemmc_reg>;
+
+	pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_bus8>;
+	pinctrl-names = "default";
+};
+
+&sdhci_2 {
+	status = "okay";
+
+	bus-width = <4>;
+	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vtf_reg>;
+
+	pinctrl-0 = <&sd2_clk>, <&sd2_cmd>, <&sd2_bus4>;
+	pinctrl-names = "default";
+};
+
+&sdhci_3 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wlan_pwrseq>;
+	vmmc-supply = <&vtf_reg>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpx2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&serial_0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&bt_en>, <&bt_res>, <&uart0_data>, <&uart0_fctl>;
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+
+		shutdown-gpios = <&gpl0 4 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpl1 0 GPIO_ACTIVE_LOW>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+
+		interrupt-parent = <&gpx2>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wakeup";
+	};
+};
+
+&serial_1 {
+	status = "okay";
+};
+
+&serial_2 {
+	status = "okay";
+};
+
+&serial_3 {
+	status = "okay";
+};
+
+&tmu {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/samsung/exynos4210-origen.dts
index 0d1e1a9c2f6e..f1927ca15e08 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-origen.dts
@@ -15,6 +15,7 @@
 #include "exynos4210.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include "exynos-mfc-reserved-memory.dtsi"
 
 / {
@@ -29,6 +30,11 @@
 		       0x70000000 0x10000000>;
 	};
 
+	aliases {
+		mmc0 = &sdhci_0;
+		mmc1 = &sdhci_2;
+	};
+
 	chosen {
 		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M init=/linuxrc";
 		stdout-path = "serial2:115200n8";
@@ -43,38 +49,38 @@
 		enable-active-high;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		up {
+		key-up {
 			label = "Up";
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_UP>;
 			wakeup-source;
 		};
 
-		down {
+		key-down {
 			label = "Down";
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DOWN>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpx1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpx1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		menu {
+		key-menu {
 			label = "Menu";
 			gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
@@ -84,8 +90,9 @@
 
 	leds {
 		compatible = "gpio-leds";
-		status {
+		led-status {
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_HEARTBEAT;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -100,6 +107,13 @@
 			compatible = "samsung,clock-xusbxti";
 			clock-frequency = <24000000>;
 		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on max8997 PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 
 	display-timings {
@@ -122,6 +136,19 @@
 	cpu0-supply = <&buck1_reg>;
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz */
+			cooling-device = <&cpu0 2 2>;
+		};
+		map1 {
+			/* Corresponds to 200MHz */
+			cooling-device = <&cpu0 4 4>;
+		};
+	};
+};
+
 &exynos_usbphy {
 	status = "okay";
 };
@@ -151,7 +178,7 @@
 	pinctrl-0 = <&i2c0_bus>;
 	pinctrl-names = "default";
 
-	max8997_pmic@66 {
+	pmic@66 {
 		compatible = "maxim,max8997-pmic";
 		reg = <0x66>;
 		interrupt-parent = <&gpx0>;
@@ -186,79 +213,74 @@
 			ldo4_reg: LDO4 {
 				regulator-name = "VDD_RTC_1.8V";
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt	= <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 			};
 
 			ldo6_reg: LDO6 {
 				regulator-name = "VMIPI_1.8V";
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt	= <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 			};
 
 			ldo7_reg: LDO7 {
 				regulator-name = "VDD_AUD_1.8V";
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt	= <1800000>;
+				regulator-max-microvolt = <1800000>;
 			};
 
 			ldo8_reg: LDO8 {
 				regulator-name = "VADC_3.3V";
 				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt	= <3300000>;
+				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo9_reg: LDO9 {
 				regulator-name = "DVDD_SWB_2.8V";
 				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt	= <2800000>;
+				regulator-max-microvolt = <2800000>;
 				regulator-always-on;
 			};
 
 			ldo10_reg: LDO10 {
 				regulator-name = "VDD_PLL_1.1V";
 				regulator-min-microvolt = <1100000>;
-				regulator-max-microvolt	= <1100000>;
+				regulator-max-microvolt = <1100000>;
 				regulator-always-on;
 			};
 
 			ldo11_reg: LDO11 {
 				regulator-name = "VDD_AUD_3V";
 				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt	= <3000000>;
+				regulator-max-microvolt = <3000000>;
 			};
 
 			ldo14_reg: LDO14 {
 				regulator-name = "AVDD18_SWB_1.8V";
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt	= <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 			};
 
 			ldo17_reg: LDO17 {
 				regulator-name = "VDD_SWB_3.3V";
 				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt	= <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 			};
 
 			ldo21_reg: LDO21 {
 				regulator-name = "VDD_MIF_1.2V";
 				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt	= <1200000>;
+				regulator-max-microvolt = <1200000>;
 				regulator-always-on;
 			};
 
 			buck1_reg: BUCK1 {
-				/*
-				* HACK: The real name is VDD_ARM_1.2V,
-				* but exynos-cpufreq does not support
-				* DT-based regulator lookup yet.
-				*/
-				regulator-name = "vdd_arm";
+				regulator-name = "VDD_ARM_1.2V";
 				regulator-min-microvolt = <950000>;
-				regulator-max-microvolt	= <1350000>;
+				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
@@ -266,7 +288,7 @@
 			buck2_reg: BUCK2 {
 				regulator-name = "VDD_INT_1.1V";
 				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt	= <1100000>;
+				regulator-max-microvolt = <1100000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
@@ -291,12 +313,17 @@
 				regulator-boot-on;
 				regulator-always-on;
 			};
+
+			EN32KHZ_AP {
+				regulator-name = "EN32KHZ_AP";
+				regulator-always-on;
+			};
 		};
 	};
 };
 
 &pinctrl_1 {
-	max8997_irq: max8997-irq {
+	max8997_irq: max8997-irq-pins {
 		samsung,pins = "gpx0-3", "gpx0-4";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
@@ -336,6 +363,8 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &tmu {
diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos4210-pinctrl.dtsi
index 520c5934a8d4..70d268f9fcb1 100644
--- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4210-pinctrl.dtsi
@@ -7,14 +7,14 @@
  * Copyright (c) 2011-2012 Linaro Ltd.
  *		www.linaro.org
  *
- * Samsung's Exynos4210 SoC pin-mux and pin-config optiosn are listed as device
- * tree nodes are listed in this file.
+ * Samsung's Exynos4210 SoC pin-mux and pin-config options are listed as device
+ * tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -22,7 +22,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -30,7 +30,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -38,7 +38,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -46,7 +46,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -54,7 +54,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -62,7 +62,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -70,7 +70,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -78,7 +78,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -86,7 +86,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe2: gpe2 {
+	gpe2: gpe2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -94,7 +94,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe3: gpe3 {
+	gpe3: gpe3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -102,7 +102,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe4: gpe4 {
+	gpe4: gpe4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -110,7 +110,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -118,7 +118,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -126,7 +126,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -134,7 +134,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -142,112 +142,112 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_a: uart-audio-a {
+	uart_audio_a: uart-audio-a-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_b: uart-audio-b {
+	uart_audio_b: uart-audio-b-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -255,7 +255,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -263,7 +263,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
@@ -271,7 +271,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -279,7 +279,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -287,105 +287,105 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_sync: lcd-sync {
+	lcd_sync: lcd-sync-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_en: lcd-en {
+	lcd_en: lcd-en-pins {
 		samsung,pins = "gpe3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_clk: lcd-clk {
+	lcd_clk: lcd-clk-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpf0-7", "gpf1-0", "gpf1-1", "gpf1-2",
 				"gpf1-3", "gpf1-6", "gpf1-7", "gpf2-0",
 				"gpf2-1", "gpf2-2", "gpf2-3", "gpf2-7",
@@ -395,7 +395,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpf0-6", "gpf0-7", "gpf1-0", "gpf1-1",
 				"gpf1-2", "gpf1-3", "gpf1-6", "gpf1-7",
 				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
@@ -406,7 +406,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
 				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
 				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
@@ -420,7 +420,7 @@
 };
 
 &pinctrl_1 {
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -428,7 +428,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -436,7 +436,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -444,7 +444,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -452,7 +452,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -460,7 +460,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk3: gpk3 {
+	gpk3: gpk3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -468,7 +468,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl0: gpl0 {
+	gpl0: gpl0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -476,7 +476,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl1: gpl1 {
+	gpl1: gpl1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -484,7 +484,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl2: gpl2 {
+	gpl2: gpl2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -492,42 +492,42 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -544,7 +544,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -561,7 +561,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -569,7 +569,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -577,238 +577,238 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_clk: sd4-clk {
+	sd4_clk: sd4-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cmd: sd4-cmd {
+	sd4_cmd: sd4-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cd: sd4-cd {
+	sd4_cd: sd4-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus1: sd4-bus-width1 {
+	sd4_bus1: sd4-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus4: sd4-bus-width4 {
+	sd4_bus4: sd4-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus8: sd4-bus-width8 {
+	sd4_bus8: sd4-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpk1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpk1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpk1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpk2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpk2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpk2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpk2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpk3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpk3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpk3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpk3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	eint0: ext-int0 {
+	eint0: ext-int0-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint8: ext-int8 {
+	eint8: ext-int8-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint15: ext-int15 {
+	eint15: ext-int15-pins {
 		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint16: ext-int16 {
+	eint16: ext-int16-pins {
 		samsung,pins = "gpx2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint31: ext-int31 {
+	eint31: ext-int31-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_io: cam-port-a-io {
+	cam_port_a_io: cam-port-a-io-pins {
 		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
 				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
 				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
@@ -817,21 +817,21 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_clk_active: cam-port-a-clk-active {
+	cam_port_a_clk_active: cam-port-a-clk-active-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_a_clk_idle: cam-port-a-clk-idle {
+	cam_port_a_clk_idle: cam-port-a-clk-idle-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -840,12 +840,12 @@
 };
 
 &pinctrl_2 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -853,7 +853,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts
index 77fc11e593ad..b566f878ed84 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts
@@ -25,6 +25,10 @@
 		reg = <0x40000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &sdhci_2;
+	};
+
 	chosen {
 		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M init=/linuxrc";
 		stdout-path = "serial1:115200n8";
@@ -40,6 +44,26 @@
 			compatible = "samsung,clock-xusbxti";
 			clock-frequency = <24000000>;
 		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz */
+			cooling-device = <&cpu0 2 2>;
+		};
+		map1 {
+			/* Corresponds to 200MHz */
+			cooling-device = <&cpu0 4 4>;
+		};
 	};
 };
 
@@ -70,61 +94,61 @@
 	pinctrl-0 = <&keypad_rows &keypad_cols>;
 	status = "okay";
 
-	key_1 {
+	key-1 {
 		keypad,row = <0>;
 		keypad,column = <3>;
 		linux,code = <2>;
 	};
 
-	key_2 {
+	key-2 {
 		keypad,row = <0>;
 		keypad,column = <4>;
 		linux,code = <3>;
 	};
 
-	key_3 {
+	key-3 {
 		keypad,row = <0>;
 		keypad,column = <5>;
 		linux,code = <4>;
 	};
 
-	key_4 {
+	key-4 {
 		keypad,row = <0>;
 		keypad,column = <6>;
 		linux,code = <5>;
 	};
 
-	key_5 {
+	key-5 {
 		keypad,row = <0>;
 		keypad,column = <7>;
 		linux,code = <6>;
 	};
 
-	key_a {
+	key-a {
 		keypad,row = <1>;
 		keypad,column = <3>;
 		linux,code = <30>;
 	};
 
-	key_b {
+	key-b {
 		keypad,row = <1>;
 		keypad,column = <4>;
 		linux,code = <48>;
 	};
 
-	key_c {
+	key-c {
 		keypad,row = <1>;
 		keypad,column = <5>;
 		linux,code = <46>;
 	};
 
-	key_d {
+	key-d {
 		keypad,row = <1>;
 		keypad,column = <6>;
 		linux,code = <32>;
 	};
 
-	key_e {
+	key-e {
 		keypad,row = <1>;
 		keypad,column = <7>;
 		linux,code = <18>;
@@ -132,14 +156,14 @@
 };
 
 &pinctrl_1 {
-	keypad_rows: keypad-rows {
+	keypad_rows: keypad-rows-pins {
 		samsung,pins = "gpx2-0", "gpx2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	keypad_cols: keypad-cols {
+	keypad_cols: keypad-cols-pins {
 		samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
 			       "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -148,6 +172,11 @@
 	};
 };
 
+&rtc {
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sdhci_2 {
 	bus-width = <4>;
 	pinctrl-names = "default";
@@ -175,10 +204,10 @@
 	cs-gpios = <&gpc1 2 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	w25x80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "w25x80";
+		compatible = "winbond,w25x80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <1000000>;
 
diff --git a/arch/arm/boot/dts/samsung/exynos4210-trats.dts b/arch/arm/boot/dts/samsung/exynos4210-trats.dts
new file mode 100644
index 000000000000..95e0e01b6ff6
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4210-trats.dts
@@ -0,0 +1,567 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4210 based Trats board device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Device tree source file for Samsung's Trats board which is based on
+ * Samsung's Exynos4210 SoC.
+ */
+
+/dts-v1/;
+#include "exynos4210.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Samsung Trats based on Exynos4210";
+	compatible = "samsung,trats", "samsung,exynos4210", "samsung,exynos4";
+	chassis-type = "handset";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x10000000
+		       0x50000000 0x10000000
+		       0x60000000 0x10000000
+		       0x70000000 0x10000000>;
+	};
+
+	aliases {
+		mmc0 = &sdhci_0;
+		mmc1 = &sdhci_2;
+		mmc2 = &sdhci_3;
+	};
+
+	chosen {
+		bootargs = "root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
+		stdout-path = "serial2:115200n8";
+	};
+
+	vemmc_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VMEM_VDD_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tsp_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_FIXED_VOLTAGES";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	cam_af_28v_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "8M_AF_2.8V_EN";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	cam_io_en_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "CAM_IO_EN";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	cam_io_12v_reg: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "8M_1.2V_EN";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vt_core_15v_reg: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "VT_CORE_1.5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		vol-down-key {
+			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <114>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		vol-up-key {
+			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
+			linux,code = <115>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		power-key {
+			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <116>;
+			label = "power";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		ok-key {
+			gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+			linux,code = <352>;
+			label = "ok";
+			debounce-interval = <10>;
+		};
+	};
+
+	wlan_pwrseq: sdhci3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpl1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti";
+			clock-frequency = <0>;
+		};
+
+		xusbxti {
+			compatible = "samsung,clock-xusbxti";
+			clock-frequency = <24000000>;
+		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on max8997 PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&camera {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu0-supply = <&varm_breg>;
+};
+
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 2 2>, <&cpu1 2 2>;
+		};
+		map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 4 4>, <&cpu1 4 4>;
+		};
+	};
+};
+
+&dsi_0 {
+	vddcore-supply = <&vusb_reg>;
+	vddio-supply = <&vmipi_reg>;
+	samsung,burst-clock-frequency = <500000000>;
+	samsung,esc-clock-frequency = <20000000>;
+	samsung,pll-clock-frequency = <24000000>;
+	status = "okay";
+
+	panel@0 {
+		reg = <0>;
+		compatible = "samsung,s6e8aa0";
+		vdd3-supply = <&vcclcd_reg>;
+		vci-supply = <&vlcd_reg>;
+		reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
+		power-on-delay = <50>;
+		reset-delay = <100>;
+		init-delay = <100>;
+		flip-horizontal;
+		flip-vertical;
+		panel-width-mm = <58>;
+		panel-height-mm = <103>;
+
+		display-timings {
+			timing-0 {
+				clock-frequency = <57153600>;
+				hactive = <720>;
+				vactive = <1280>;
+				hfront-porch = <5>;
+				hback-porch = <5>;
+				hsync-len = <5>;
+				vfront-porch = <13>;
+				vback-porch = <1>;
+				vsync-len = <2>;
+			};
+		};
+	};
+};
+
+&exynos_usbphy {
+	status = "okay";
+	vbus-supply = <&safe1_sreg>;
+};
+
+&fimc_0 {
+	status = "okay";
+	assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+			  <&clock CLK_SCLK_FIMC0>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimc_1 {
+	status = "okay";
+	assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+			  <&clock CLK_SCLK_FIMC1>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimc_2 {
+	status = "okay";
+	assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+			  <&clock CLK_SCLK_FIMC2>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+		assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimc_3 {
+	status = "okay";
+	assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+			  <&clock CLK_SCLK_FIMC3>;
+	assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
+	assigned-clock-rates = <0>, <160000000>;
+};
+
+&fimd {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&hsotg {
+	vusb_d-supply = <&vusb_reg>;
+	vusb_a-supply = <&vusbdac_reg>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&i2c_3 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <400000>;
+	pinctrl-0 = <&i2c3_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	touchscreen@48 {
+		compatible = "melfas,mms114";
+		reg = <0x48>;
+		interrupt-parent = <&gpx0>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+		avdd-supply = <&tsp_reg>;
+		vdd-supply = <&tsp_reg>;
+	};
+};
+
+&i2c_5 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+	pinctrl-0 = <&i2c5_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pmic@66 {
+		compatible = "maxim,max8997-pmic";
+
+		reg = <0x66>;
+		interrupts-extended = <&gpx0 7 IRQ_TYPE_LEVEL_LOW>,
+				      <&gpx2 3 IRQ_TYPE_EDGE_FALLING>;
+
+		max8997,pmic-buck1-uses-gpio-dvs;
+		max8997,pmic-buck2-uses-gpio-dvs;
+		max8997,pmic-buck5-uses-gpio-dvs;
+
+		max8997,pmic-ignore-gpiodvs-side-effect;
+		max8997,pmic-buck125-default-dvs-idx = <0>;
+
+		max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>,
+						 <&gpx0 6 GPIO_ACTIVE_HIGH>,
+						 <&gpl0 0 GPIO_ACTIVE_HIGH>;
+
+		max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
+
+		max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
+						 <950000>,  <900000>,
+						 <1100000>, <1000000>,
+						 <950000>,  <900000>;
+
+		max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
+
+		regulators {
+			valive_reg: LDO2 {
+				regulator-name = "VALIVE_1.1V_C210";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vusb_reg: LDO3 {
+				regulator-name = "VUSB_1.1V_C210";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			vmipi_reg: LDO4 {
+				regulator-name = "VMIPI_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vpda_reg: LDO6 {
+				regulator-name = "VCC_1.8V_PDA";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcam_reg: LDO7 {
+				regulator-name = "CAM_ISP_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vusbdac_reg: LDO8 {
+				regulator-name = "VUSB+VDAC_3.3V_C210";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vccpda_reg: LDO9 {
+				regulator-name = "VCC_2.8V_PDA";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+
+			vpll_reg: LDO10 {
+				regulator-name = "VPLL_1.1V_C210";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vtcam_reg: LDO12 {
+				regulator-name = "VT_CAM_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcclcd_reg: LDO13 {
+				regulator-name = "VCC_3.3V_LCD";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vlcd_reg: LDO15 {
+				regulator-name = "VLCD_2.2V";
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+			};
+
+			camsensor_reg: LDO16 {
+				regulator-name = "CAM_SENSOR_IO_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			tflash_reg: LDO17 {
+				regulator-name = "VTF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vddq_reg: LDO21 {
+				regulator-name = "VDDQ_M1M2_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			varm_breg: BUCK1 {
+				regulator-name = "VARM_1.2V_C210";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+			};
+
+			vint_breg: BUCK2 {
+				regulator-name = "VINT_1.1V_C210";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			camisp_breg: BUCK4 {
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vmem_breg: BUCK5 {
+				regulator-name = "VMEM_1.2V_C210";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vccsub_breg: BUCK7 {
+				regulator-name = "VCC_SUB_2.0V";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			safe1_sreg: ESAFEOUT1 {
+				regulator-name = "SAFEOUT1";
+			};
+
+			safe2_sreg: ESAFEOUT2 {
+				regulator-name = "SAFEOUT2";
+				regulator-boot-on;
+			};
+
+			EN32KHZ_AP {
+				regulator-name = "EN32KHZ_AP";
+				regulator-always-on;
+			};
+
+			EN32KHZ_CP {
+				regulator-name = "EN32KHZ_CP";
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&pinctrl_1 {
+	bt_shutdown: bt-shutdown-pins {
+		samsung,pins = "gpl1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_host_wakeup: bt-host-wakeup-pins {
+		samsung,pins = "gpx2-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_device_wakeup: bt-device-wakeup-pins {
+		samsung,pins = "gpx3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&sdhci_0 {
+	bus-width = <8>;
+	non-removable;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vemmc_reg>;
+	status = "okay";
+};
+
+&sdhci_2 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
+	pinctrl-names = "default";
+	vmmc-supply = <&tflash_reg>;
+	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&sdhci_3 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wlan_pwrseq>;
+	vmmc-supply = <&tflash_reg>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpx2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&serial_0 {
+	status = "okay";
+	pinctrl-0 = <&uart0_data &uart0_fctl>;
+	pinctrl-names = "default";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
+		pinctrl-names = "default";
+		shutdown-gpios = <&gpl1 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&serial_1 {
+	status = "okay";
+};
+
+&serial_2 {
+	status = "okay";
+};
+
+&serial_3 {
+	status = "okay";
+};
+
+&tmu {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/samsung/exynos4210-universal_c210.dts
index 09d3d54d09ff..bdc30f8cf748 100644
--- a/arch/arm/boot/dts/exynos4210-universal_c210.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-universal_c210.dts
@@ -16,11 +16,18 @@
 / {
 	model = "Samsung Universal C210 based on Exynos4210 rev0";
 	compatible = "samsung,universal_c210", "samsung,exynos4210", "samsung,exynos4";
+	chassis-type = "handset";
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x10000000
-			0x50000000 0x10000000>;
+		reg = <0x40000000 0x10000000
+		       0x50000000 0x10000000>;
+	};
+
+	aliases {
+		mmc0 = &sdhci_0;
+		mmc1 = &sdhci_2;
+		mmc2 = &sdhci_3;
 	};
 
 	chosen {
@@ -39,10 +46,17 @@
 			compatible = "samsung,clock-xusbxti";
 			clock-frequency = <24000000>;
 		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 
 	vemmc_reg: voltage-regulator {
-	        compatible = "regulator-fixed";
+		compatible = "regulator-fixed";
 		regulator-name = "VMEM_VDD_2_8V";
 		regulator-min-microvolt = <2800000>;
 		regulator-max-microvolt = <2800000>;
@@ -50,6 +64,11 @@
 		enable-active-high;
 	};
 
+	wlan_pwrseq: sdhci3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpe3 1 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -99,7 +118,7 @@
 	};
 
 	tsp_reg: voltage-regulator {
-	        compatible = "regulator-fixed";
+		compatible = "regulator-fixed";
 		regulator-name = "TSP_2_8V";
 		regulator-min-microvolt = <2800000>;
 		regulator-max-microvolt = <2800000>;
@@ -107,15 +126,15 @@
 		enable-active-high;
 	};
 
-	spi-lcd {
+	spi-3 {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		gpio-sck = <&gpy3 1 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpy3 3 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpy3 1 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpy3 3 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
-		cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpy4 3 GPIO_ACTIVE_LOW>;
 
 		lcd@0 {
 			compatible = "samsung,ld9040";
@@ -124,8 +143,6 @@
 			vci-supply = <&ldo17_reg>;
 			reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
 			spi-max-frequency = <1200000>;
-			spi-cpol;
-			spi-cpha;
 			power-on-delay = <10>;
 			reset-delay = <10>;
 			panel-width-mm = <90>;
@@ -166,7 +183,8 @@
 
 	hdmi_ddc: i2c-ddc {
 		compatible = "i2c-gpio";
-		gpios = <&gpe4 2 GPIO_ACTIVE_HIGH &gpe4 3 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpe4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpe4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		i2c-gpio,delay-us = <100>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -177,31 +195,27 @@
 	};
 };
 
-&amba {
-	mdma0: mdma@12840000 {
-		compatible = "arm,pl330", "arm,primecell";
-		reg = <0x12840000 0x1000>;
-		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&clock CLK_MDMA>;
-		clock-names = "apb_pclk";
-		#dma-cells = <1>;
-		#dma-channels = <8>;
-		#dma-requests = <1>;
-		power-domains = <&pd_lcd0>;
-	};
-};
-
 &camera {
 	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <>;
 };
 
 &cpu0 {
 	cpu0-supply = <&vdd_arm_reg>;
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz */
+			cooling-device = <&cpu0 2 2>;
+		};
+		map1 {
+			/* Corresponds to 200MHz */
+			cooling-device = <&cpu0 4 4>;
+		};
+	};
+};
+
 &ehci {
 	status = "okay";
 	phys = <&exynos_usbphy 1>;
@@ -319,7 +333,7 @@
 		max8952,sync-freq = <0>;
 		max8952,ramp-speed = <0>;
 
-		regulator-name = "vdd_arm";
+		regulator-name = "VARM_1.2V_C210";
 		regulator-min-microvolt = <770000>;
 		regulator-max-microvolt = <1400000>;
 		regulator-always-on;
@@ -505,7 +519,7 @@
 };
 
 &mct {
-	compatible = "none";
+	status = "disabled";
 };
 
 &mdma1 {
@@ -522,19 +536,37 @@
 };
 
 &pinctrl_1 {
-	lp3974_irq: lp3974-irq {
+	bt_shutdown: bt-shutdown-pins {
+		samsung,pins = "gpe1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_host_wakeup: bt-host-wakeup-pins {
+		samsung,pins = "gpx2-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_device_wakeup: bt-device-wakeup-pins {
+		samsung,pins = "gpx3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	lp3974_irq: lp3974-irq-pins {
 		samsung,pins = "gpx0-7", "gpx2-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 };
 
 &pinctrl_0 {
-	i2c_ddc_bus: i2c-ddc-bus {
+	i2c_ddc_bus: i2c-ddc-bus-pins {
 		samsung,pins = "gpe4-2", "gpe4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -547,6 +579,12 @@
 	status = "okay";
 };
 
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sdhci_0 {
 	bus-width = <8>;
 	non-removable;
@@ -565,10 +603,44 @@
 	status = "okay";
 };
 
+&sdhci_3 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wlan_pwrseq>;
+	vmmc-supply = <&ldo5_reg>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&gpx2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
 &serial_0 {
 	status = "okay";
 	/delete-property/dmas;
 	/delete-property/dma-names;
+	pinctrl-0 = <&uart0_data &uart0_fctl>;
+	pinctrl-names = "default";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
+		pinctrl-names = "default";
+		shutdown-gpios = <&gpe1 4 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &serial_1 {
@@ -589,17 +661,29 @@
 	/delete-property/dma-names;
 };
 
+&soc {
+	mdma0: dma-controller@12840000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x12840000 0x1000>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clock CLK_MDMA>;
+		clock-names = "apb_pclk";
+		#dma-cells = <1>;
+		power-domains = <&pd_lcd0>;
+	};
+};
+
 &sysram {
-	smp-sysram@0 {
+	smp-sram@0 {
 		status = "disabled";
 	};
 
-	smp-sysram@5000 {
+	smp-sram@5000 {
 		compatible = "samsung,exynos4210-sysram";
 		reg = <0x5000 0x1000>;
 	};
 
-	smp-sysram@1f000 {
+	smp-sram@1f000 {
 		status = "disabled";
 	};
 };
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/samsung/exynos4210.dtsi
index 554819ae1446..510e8665d1a2 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4210.dtsi
@@ -28,10 +28,166 @@
 		pinctrl2 = &pinctrl_2;
 	};
 
+	bus_acp: bus-acp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_ACP>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_acp_opp_table>;
+		status = "disabled";
+
+		bus_acp_opp_table: opp-table {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+			};
+			opp-160000000 {
+				opp-hz = /bits/ 64 <160000000>;
+			};
+			opp-200000000 {
+				opp-hz = /bits/ 64 <200000000>;
+			};
+		};
+	};
+
+	bus_display: bus-display {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK160>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_display_opp_table>;
+		status = "disabled";
+
+		bus_display_opp_table: opp-table {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+			};
+			opp-160000000 {
+				opp-hz = /bits/ 64 <160000000>;
+			};
+		};
+	};
+
+	bus_dmc: bus-dmc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_DMC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		status = "disabled";
+
+		bus_dmc_opp_table: opp-table {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+				opp-microvolt = <1025000>;
+			};
+			opp-267000000 {
+				opp-hz = /bits/ 64 <267000000>;
+				opp-microvolt = <1050000>;
+			};
+			opp-400000000 {
+				opp-hz = /bits/ 64 <400000000>;
+				opp-microvolt = <1150000>;
+				opp-suspend;
+			};
+		};
+	};
+
+	bus_fsys: bus-fsys {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK133>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_fsys_opp_table>;
+		status = "disabled";
+
+		bus_fsys_opp_table: opp-table {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp-10000000 {
+				opp-hz = /bits/ 64 <10000000>;
+			};
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+			};
+		};
+	};
+
+	bus_lcd0: bus-lcd0 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK200>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_leftbus: bus-leftbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_GDL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mfc: bus-mfc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_SCLK_MFC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_peri: bus-peri {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK100>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_peri_opp_table>;
+		status = "disabled";
+
+		bus_peri_opp_table: opp-table {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp-5000000 {
+				opp-hz = /bits/ 64 <5000000>;
+			};
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+		};
+	};
+
+	bus_rightbus: bus-rightbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_GDR>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
 		cpu0: cpu@900 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
@@ -71,6 +227,22 @@
 		};
 	};
 
+	bus_leftbus_opp_table: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+		opp-160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+		};
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-suspend;
+		};
+	};
+
 	soc: soc {
 		sysram: sram@2020000 {
 			compatible = "mmio-sram";
@@ -79,12 +251,12 @@
 			#size-cells = <1>;
 			ranges = <0 0x02020000 0x20000>;
 
-			smp-sysram@0 {
+			smp-sram@0 {
 				compatible = "samsung,exynos4210-sysram";
 				reg = <0x0 0x1000>;
 			};
 
-			smp-sysram@1f000 {
+			smp-sram@1f000 {
 				compatible = "samsung,exynos4210-sysram-ns";
 				reg = <0x1f000 0x1000>;
 			};
@@ -92,16 +264,18 @@
 
 		pd_lcd1: power-domain@10023ca0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023CA0 0x20>;
+			reg = <0x10023ca0 0x20>;
 			#power-domain-cells = <0>;
 			label = "LCD1";
 		};
 
-		l2c: l2-cache-controller@10502000 {
+		l2c: cache-controller@10502000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x10502000 0x1000>;
 			cache-unified;
 			cache-level = <2>;
+			prefetch-data = <1>;
+			prefetch-instr = <1>;
 			arm,tag-latency = <2 2 1>;
 			arm,data-latency = <2 2 1>;
 		};
@@ -166,13 +340,13 @@
 			iommus = <&sysmmu_g2d>;
 		};
 
-		ppmu_acp: ppmu_acp@10ae0000 {
+		ppmu_acp: ppmu@10ae0000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x10ae0000 0x2000>;
 			status = "disabled";
 		};
 
-		ppmu_lcd1: ppmu_lcd1@12240000 {
+		ppmu_lcd1: ppmu@12240000 {
 			compatible = "samsung,exynos-ppmu";
 			reg = <0x12240000 0x2000>;
 			clocks = <&clock CLK_PPMULCD1>;
@@ -182,7 +356,7 @@
 
 		sysmmu_g2d: sysmmu@12a20000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x12A20000 0x1000>;
+			reg = <0x12a20000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 7>;
 			clock-names = "sysmmu", "master";
@@ -201,188 +375,32 @@
 			power-domains = <&pd_lcd1>;
 			#iommu-cells = <0>;
 		};
+	};
+};
 
-		bus_dmc: bus_dmc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_DMC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_dmc_opp_table>;
-			status = "disabled";
-		};
-
-		bus_acp: bus_acp {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_ACP>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_acp_opp_table>;
-			status = "disabled";
-		};
-
-		bus_peri: bus_peri {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK100>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_peri_opp_table>;
-			status = "disabled";
-		};
-
-		bus_fsys: bus_fsys {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK133>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_fsys_opp_table>;
-			status = "disabled";
-		};
-
-		bus_display: bus_display {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK160>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_display_opp_table>;
-			status = "disabled";
-		};
-
-		bus_lcd0: bus_lcd0 {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK200>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_leftbus: bus_leftbus {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_GDL>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_rightbus: bus_rightbus {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_GDR>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_mfc: bus_mfc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_SCLK_MFC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_dmc_opp_table: opp_table1 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-				opp-microvolt = <1025000>;
-			};
-			opp-267000000 {
-				opp-hz = /bits/ 64 <267000000>;
-				opp-microvolt = <1050000>;
-			};
-			opp-400000000 {
-				opp-hz = /bits/ 64 <400000000>;
-				opp-microvolt = <1150000>;
-				opp-suspend;
-			};
-		};
-
-		bus_acp_opp_table: opp_table2 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-			};
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-		};
-
-		bus_peri_opp_table: opp_table3 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-5000000 {
-				opp-hz = /bits/ 64 <5000000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-		};
-
-		bus_fsys_opp_table: opp_table4 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-10000000 {
-				opp-hz = /bits/ 64 <10000000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-			};
-		};
-
-		bus_display_opp_table: opp_table5 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-			};
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-			};
-		};
-
-		bus_leftbus_opp_table: opp_table6 {
-			compatible = "operating-points-v2";
-			opp-shared;
+&cpu_alert0 {
+	temperature = <85000>; /* millicelsius */
+};
 
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-				opp-suspend;
-			};
-		};
-	};
+&cpu_alert1 {
+	temperature = <100000>; /* millicelsius */
+};
 
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			polling-delay-passive = <0>;
-			polling-delay = <0>;
-			thermal-sensors = <&tmu 0>;
+&cpu_alert2 {
+	temperature = <110000>; /* millicelsius */
+};
 
-			trips {
-				cpu_alert0: cpu-alert-0 {
-					temperature = <85000>; /* millicelsius */
-				};
-				cpu_alert1: cpu-alert-1 {
-					temperature = <100000>; /* millicelsius */
-				};
-				cpu_alert2: cpu-alert-2 {
-					temperature = <110000>; /* millicelsius */
-				};
-			};
-		};
-	};
+&cpu_thermal {
+	/*
+	 * Exynos 4210 supports thermal interrupts, but only for the rising
+	 * threshold.  This means that polling is not needed for preventing
+	 * overheating, but only for decreasing cooling when possible. Hence we
+	 * poll with a high delay.  Ideally, we would disable polling for the
+	 * first trip point, but this isn't really possible without outrageous
+	 * hacks.
+	 */
+	polling-delay-passive = <5000>;
+	polling-delay = <5000>;
 };
 
 &gic {
@@ -463,7 +481,7 @@
 			  "ppmmu3";
 	operating-points-v2 = <&gpu_opp_table>;
 
-	gpu_opp_table: opp_table {
+	gpu_opp_table: opp-table {
 		compatible = "operating-points-v2";
 
 		opp-160000000 {
@@ -516,8 +534,6 @@
 	compatible = "samsung,exynos4210-tmu";
 	clocks = <&clock CLK_TMU_APBIF>;
 	clock-names = "tmu_apbif";
-	samsung,tmu_gain = <15>;
-	samsung,tmu_reference_voltage = <7>;
 };
 
 #include "exynos4210-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/samsung/exynos4212-tab3-3g8.dts b/arch/arm/boot/dts/samsung/exynos4212-tab3-3g8.dts
new file mode 100644
index 000000000000..d96b2dd44608
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4212-tab3-3g8.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 8.0 3G board device tree
+ * source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212-tab3.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 3 8.0 3G (SM-T311) based on Exynos4212";
+	compatible = "samsung,t311", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+	chassis-type = "tablet";
+};
+
+/* Pin control sleep state overrides */
+&sleep0 {
+	PIN_SLP(gpb-5, INPUT, UP);
+};
+
+&sleep1 {
+	PIN_SLP(gpl0-0, OUT0, NONE);
+	PIN_SLP(gpl1-0, OUT0, NONE);
+	PIN_SLP(gpl2-4, OUT0, NONE);
+	PIN_SLP(gpm3-3, OUT1, NONE);
+};
diff --git a/arch/arm/boot/dts/samsung/exynos4212-tab3-lte8.dts b/arch/arm/boot/dts/samsung/exynos4212-tab3-lte8.dts
new file mode 100644
index 000000000000..bbb398eca7b0
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4212-tab3-lte8.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 8.0 LTE board device tree
+ * source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212-tab3.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 3 8.0 LTE (SM-T315) based on Exynos4212";
+	compatible = "samsung,t315", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+	chassis-type = "tablet";
+};
+
+/* Pin control sleep state overrides */
+&sleep0 {
+	PIN_SLP(gpa0-4, INPUT, UP);
+	PIN_SLP(gpa0-5, INPUT, UP);
+
+	PIN_SLP(gpb-5, INPUT, UP);
+
+	PIN_SLP(gpc0-0, PREV, NONE);
+	PIN_SLP(gpc1-3, INPUT, NONE);
+
+	PIN_SLP(gpf1-6, INPUT, NONE);
+	PIN_SLP(gpf2-2, PREV, NONE);
+};
+
+&sleep1 {
+	PIN_SLP(gpl0-0, PREV, NONE);
+
+	PIN_SLP(gpl1-0, PREV, NONE);
+
+	PIN_SLP(gpl2-1, INPUT, DOWN);
+	PIN_SLP(gpl2-2, INPUT, DOWN);
+	PIN_SLP(gpl2-4, OUT0, NONE);
+	PIN_SLP(gpl2-5, PREV, NONE);
+
+	PIN_SLP(gpm3-3, OUT1, NONE);
+};
diff --git a/arch/arm/boot/dts/samsung/exynos4212-tab3-wifi8.dts b/arch/arm/boot/dts/samsung/exynos4212-tab3-wifi8.dts
new file mode 100644
index 000000000000..54cb01703b60
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4212-tab3-wifi8.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
+ * source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212-tab3.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 3 8.0 WiFi (SM-T310) based on Exynos4212";
+	compatible = "samsung,t310", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+	chassis-type = "tablet";
+};
+
+&i2c_lightsensor {
+	status = "okay";
+
+	lightsensor@10 {
+		compatible = "capella,cm3323";
+		reg = <0x10>;
+	};
+};
diff --git a/arch/arm/boot/dts/samsung/exynos4212-tab3.dtsi b/arch/arm/boot/dts/samsung/exynos4212-tab3.dtsi
new file mode 100644
index 000000000000..d7954ff466b4
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4212-tab3.dtsi
@@ -0,0 +1,1309 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 board common source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212.dtsi"
+#include "exynos4412-ppmu-common.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "exynos-pinctrl.h"
+
+/ {
+	compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+
+	memory@40000000 {
+		device_type = "memory";
+
+		/*
+		 * Technically 1.5GB is available, but the latter 512MB is handled
+		 * in a special way by downstream (every second page is skipped),
+		 * and thus doesn't initialize correctly on mainline. Only 1020M is
+		 * used for now.
+		 */
+		reg = <0x40000000 0x3fc00000>;
+	};
+
+	aliases {
+		mmc0 = &mshc_0;   /* Internal storage */
+		mmc1 = &sdhci_2;  /* SD card */
+		mmc2 = &sdhci_3;  /* WiFi */
+	};
+
+	chosen {
+		stdout-path = &serial_2;
+
+		/* Default S-BOOT bootloader loads initramfs here */
+		linux,initrd-start = <0x42000000>;
+		linux,initrd-end = <0x42800000>;
+	};
+
+	firmware@204f000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x0204F000 0x1000>;
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti";
+			clock-frequency = <0>;
+		};
+
+		xusbxti {
+			compatible = "samsung,clock-xusbxti";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
+
+		key-power {
+			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		key-up {
+			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		key-down {
+			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		key-home {
+			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+			label = "home";
+			debounce-interval = <10>;
+		};
+
+		switch-hall-sensor {
+			gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			label = "hall effect sensor";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	led-touchkeys {
+		compatible = "regulator-led";
+		vled-supply = <&ldo20_reg>;
+		default-state = "off";
+		function = LED_FUNCTION_KBD_BACKLIGHT;
+		color = <LED_COLOR_ID_WHITE>;
+	};
+
+	i2c_max77693: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmic@66 {
+			compatible = "maxim,max77693";
+			reg = <0x66>;
+			interrupt-parent = <&gpx1>;
+			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77693_irq>;
+
+			regulators {
+				esafeout1_reg: ESAFEOUT1 {
+					regulator-name = "ESAFEOUT1";
+					regulator-boot-on;
+				};
+
+				esafeout2_reg: ESAFEOUT2 {
+					regulator-name = "ESAFEOUT2";
+				};
+
+				charger_reg: CHARGER {
+					regulator-name = "CHARGER";
+					regulator-min-microamp = <60000>;
+					regulator-max-microamp = <2580000>;
+					regulator-boot-on;
+				};
+			};
+
+			charger {
+				compatible = "maxim,max77693-charger";
+
+				maxim,constant-microvolt = <4350000>;
+				maxim,min-system-microvolt = <3600000>;
+				maxim,thermal-regulation-celsius = <100>;
+				maxim,battery-overcurrent-microamp = <3500000>;
+				maxim,charge-input-threshold-microvolt = <4300000>;
+			};
+		};
+	};
+
+	i2c_max77693_fuel: i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fuel-gauge@36 {
+			compatible = "maxim,max17050";
+			reg = <0x36>;
+			interrupt-parent = <&gpx2>;
+			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77693_fuel_irq>;
+
+			maxim,over-heat-temp = <500>;
+			maxim,over-volt = <4500>;
+		};
+	};
+
+	i2c_magnetometer: i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@2e {
+			compatible = "yamaha,yas532";
+			reg = <0x2e>;
+			iovdd-supply = <&ldo3_reg>;
+			mount-matrix = "-1", "0", "0",
+					  "0", "1", "0",
+					  "0", "0", "-1";
+		};
+	};
+
+	i2c_lightsensor: i2c-gpio-4 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		/* WiFi model uses CM3323, 3G/LTE use CM36653 */
+	};
+
+	i2c_bl: i2c-gpio-5 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight: backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+
+			bl-name = "lcd-bl";
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x78>; /* 120 */
+
+			power-supply = <&vbatt_reg>;
+			enable-supply = <&backlight_reset_supply>;
+
+			pwms = <&pwm 1 78770 0>;
+			pwm-names = "lp8556";
+
+			rom-a3h {
+				rom-addr = /bits/ 8 <0xa3>;
+				rom-val = /bits/ 8 <0x5e>;
+			};
+
+			rom-a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x34>;
+			};
+
+			rom-a7h {
+				rom-addr = /bits/ 8 <0xa7>;
+				rom-val = /bits/ 8 <0xfa>;
+			};
+		};
+	};
+
+	vbatt_reg: voltage-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VBATT";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	backlight_reset_supply: voltage-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "BACKLIGHT_ENVDDIO";
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_reset>;
+		gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	display_3v3_supply: voltage-regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "DISPLAY_3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_en>;
+		gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */
+		enable-active-high;
+	};
+
+	mic_bias_reg: voltage-regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "MICBIAS_LDO_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	submic_bias_reg: voltage-regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "SUB_MICBIAS_LDO_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	sound: sound {
+		compatible = "samsung,midas-audio";
+		model = "TAB3";
+		mic-bias-supply = <&mic_bias_reg>;
+		submic-bias-supply = <&submic_bias_reg>;
+
+		audio-routing = "HP", "HPOUT1L",
+				"HP", "HPOUT1R",
+
+				"SPK", "SPKOUTLN",
+				"SPK", "SPKOUTLP",
+				"SPK", "SPKOUTRN",
+				"SPK", "SPKOUTRP",
+
+				"RCV", "HPOUT2N",
+				"RCV", "HPOUT2P",
+
+				"LINE", "LINEOUT2N",
+				"LINE", "LINEOUT2P",
+
+				"HDMI", "LINEOUT1N",
+				"HDMI", "LINEOUT1P",
+
+				"IN2LP:VXRN", "MICBIAS1",
+				"IN2LN", "MICBIAS1",
+				"Main Mic", "MICBIAS1",
+
+				"IN1RP", "MICBIAS2",
+				"IN1RN", "MICBIAS2",
+				"Sub Mic", "MICBIAS2",
+
+				"IN1LP", "Headset Mic",
+				"IN1LN", "Headset Mic";
+
+		cpu {
+			sound-dai = <&i2s0 0>;
+		};
+
+		codec {
+			sound-dai = <&wm1811>;
+		};
+	};
+
+	wlan_pwrseq: sdhci3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
+		clocks = <&s5m8767_osc S2MPS11_CLK_BT>;
+		clock-names = "ext_clock";
+	};
+};
+
+&bus_acp {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_c2c {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_display {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_dmc {
+	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+	vdd-supply = <&buck1_reg>;
+	status = "okay";
+};
+
+&bus_fsys {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_leftbus {
+	devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+	vdd-supply = <&buck3_reg>;
+	status = "okay";
+};
+
+&bus_mfc {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_peri {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_rightbus {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu0-supply = <&buck2_reg>;
+};
+
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>;
+		};
+		map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>;
+		};
+	};
+};
+
+&dsi_0 {
+	vddcore-supply = <&ldo8_reg>;
+	vddio-supply = <&ldo10_reg>;
+	samsung,burst-clock-frequency = <500000000>;
+	samsung,esc-clock-frequency = <20000000>;
+	samsung,pll-clock-frequency = <24000000>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "samsung,lsl080al02", "samsung,s6d7aa0";
+		reg = <0>;
+		power-supply = <&display_3v3_supply>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_nrst>;
+		reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+	};
+};
+
+&exynos_usbphy {
+	vbus-supply = <&esafeout1_reg>;
+	status = "okay";
+};
+
+&fimd {
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&buck4_reg>;
+	status = "okay";
+};
+
+&hsotg {
+	vusb_d-supply = <&ldo15_reg>;
+	vusb_a-supply = <&ldo12_reg>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&i2c_1 {
+	pinctrl-0 = <&i2c1_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	lis3dh: accelerometer@19 {
+		/* K2DH seems to be the same as lis2dh12 in terms of registers */
+		compatible = "st,lis2dh12-accel";
+		reg = <0x19>;
+
+		interrupt-parent = <&gpx0>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+		vdd-supply = <&ldo17_reg>;
+		vddio-supply = <&ldo3_reg>;
+
+		mount-matrix = "-1", "0", "0",
+				  "0", "1", "0",
+				  "0", "0", "-1";
+	};
+};
+
+&i2c_3 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <400000>;
+	pinctrl-0 = <&i2c3_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	touchscreen@48 {
+		/* MELFAS MMS252, using MMS114 compatible for now */
+		compatible = "melfas,mms114";
+		reg = <0x48>;
+		interrupt-parent = <&gpb>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <1280>;
+		avdd-supply = <&ldo21_reg>;
+		vdd-supply = <&ldo25_reg>;
+		linux,keycodes = <KEY_MENU KEY_BACK>;
+	};
+};
+
+&i2c_4 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+	pinctrl-0 = <&i2c4_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	wm1811: audio-codec@1a {
+		compatible = "wlf,wm1811";
+		reg = <0x1a>;
+		clocks = <&pmu_system_controller 0>;
+		clock-names = "MCLK1";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpx3>;
+		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		#sound-dai-cells = <0>;
+
+		wlf,gpio-cfg = <0x3 0x0 0x0 0x0 0x0 0x0
+			0x0 0x8000 0x0 0x0 0x0>;
+		wlf,micbias-cfg = <0x25 0x2f>;
+
+		wlf,lineout1-feedback;
+		wlf,lineout1-se;
+		wlf,lineout2-se;
+		wlf,ldoena-always-driven;
+
+		AVDD2-supply = <&ldo3_reg>;
+		CPVDD-supply = <&ldo3_reg>;
+		DBVDD1-supply = <&ldo3_reg>;
+		DBVDD2-supply = <&ldo3_reg>;
+		DBVDD3-supply = <&ldo3_reg>;
+		SPKVDD1-supply = <&vbatt_reg>;
+		SPKVDD2-supply = <&vbatt_reg>;
+		wlf,ldo1ena-gpios = <&gpm4 4 GPIO_ACTIVE_HIGH>;
+		wlf,ldo2ena-gpios = <&gpm4 4 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&i2c_7 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+	pinctrl-0 = <&i2c7_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	s5m8767: pmic@66 {
+		compatible = "samsung,s5m8767-pmic";
+		reg = <0x66>;
+		interrupt-parent = <&gpx0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+		wakeup-source;
+
+		s5m8767,pmic-buck-default-dvs-idx = <1>;
+
+		s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>,
+						 <&gpm3 1 GPIO_ACTIVE_HIGH>,
+						 <&gpm3 2 GPIO_ACTIVE_HIGH>;
+
+		s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>,
+						 <&gpf3 2 GPIO_ACTIVE_HIGH>,
+						 <&gpf3 3 GPIO_ACTIVE_HIGH>;
+
+		s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>;
+
+		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>;
+
+		s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VALIVE_1.0V_AP";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VM1M2_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "VCC_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <1>;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "VCC_3.3V_MHL";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>;
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "VMIPI_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				op_mode = <3>;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "VSIL_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				op_mode = <1>;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "VMIPI_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <3>;
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "VUOTG_3.0V";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				op_mode = <1>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "VCC_1.8V_MHL";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "VHSIC_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				op_mode = <1>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "VCC_2.8V_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <1>;
+				regulator-always-on;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "VLED_IC_1.9V";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+				op_mode = <1>;
+				regulator-always-on;
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "VTOUCH_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>;
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "TSP_VDD_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>;
+			};
+
+			ldo22_reg: LDO22 {
+				regulator-name = "5M_AF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <1>;
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "VTF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <3>;
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "LEDA_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <1>;
+			};
+
+			ldo25_reg: LDO25 {
+				regulator-name = "TSP_VDD_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "CAM_IO_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "VTCAM_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_ARM";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_INT";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_G3D";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "VMEM_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt	= <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				op_mode = <1>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+
+		s5m8767_osc: clocks {
+			compatible = "samsung,s5m8767-clk";
+			#clock-cells = <1>;
+			clock-output-names = "en32khz_ap",
+					     "en32khz_cp",
+					     "en32khz_bt";
+		};
+	};
+};
+
+&i2s0 {
+	pinctrl-0 = <&i2s0_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mshc_0 {
+	broken-cd;
+	non-removable;
+	card-detect-delay = <200>;
+	vmmc-supply = <&ldo22_reg>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <0>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+	pinctrl-names = "default";
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	status = "okay";
+};
+
+&pinctrl_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep0>;
+
+	lcd_en: lcd-en-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	lcd_nrst: lcd-nrst-pins {
+		samsung,pins = "gpf0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	s5m8767_ds: s5m8767-ds-pins {
+		samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	sleep0: sleep-state {
+		PIN_SLP(gpa0-0, INPUT, NONE);
+		PIN_SLP(gpa0-1, OUT0, NONE);
+		PIN_SLP(gpa0-2, INPUT, NONE);
+		PIN_SLP(gpa0-3, INPUT, UP);
+		PIN_SLP(gpa0-4, INPUT, DOWN);
+		PIN_SLP(gpa0-5, INPUT, DOWN);
+		PIN_SLP(gpa0-6, INPUT, DOWN);
+		PIN_SLP(gpa0-7, INPUT, DOWN);
+
+		PIN_SLP(gpa1-0, INPUT, DOWN);
+		PIN_SLP(gpa1-1, INPUT, DOWN);
+		PIN_SLP(gpa1-2, INPUT, DOWN);
+		PIN_SLP(gpa1-3, INPUT, DOWN);
+		PIN_SLP(gpa1-4, INPUT, DOWN);
+		PIN_SLP(gpa1-5, INPUT, DOWN);
+
+		PIN_SLP(gpb-0, INPUT, NONE);
+		PIN_SLP(gpb-1, INPUT, NONE);
+		PIN_SLP(gpb-2, INPUT, NONE);
+		PIN_SLP(gpb-3, INPUT, NONE);
+		PIN_SLP(gpb-4, INPUT, DOWN);
+		PIN_SLP(gpb-5, INPUT, DOWN);
+		PIN_SLP(gpb-6, INPUT, DOWN);
+		PIN_SLP(gpb-7, INPUT, DOWN);
+
+		PIN_SLP(gpc0-0, INPUT, DOWN);
+		PIN_SLP(gpc0-1, INPUT, DOWN);
+		PIN_SLP(gpc0-2, INPUT, NONE);
+		PIN_SLP(gpc0-3, INPUT, NONE);
+		PIN_SLP(gpc0-4, INPUT, NONE);
+
+		PIN_SLP(gpc1-0, INPUT, DOWN);
+		PIN_SLP(gpc1-1, INPUT, DOWN);
+		PIN_SLP(gpc1-2, INPUT, DOWN);
+		PIN_SLP(gpc1-3, INPUT, DOWN);
+		PIN_SLP(gpc1-4, INPUT, DOWN);
+
+		PIN_SLP(gpd0-0, INPUT, DOWN);
+		PIN_SLP(gpd0-1, OUT0, NONE);
+		PIN_SLP(gpd0-2, INPUT, NONE);
+		PIN_SLP(gpd0-3, INPUT, NONE);
+
+		PIN_SLP(gpd1-0, INPUT, DOWN);
+		PIN_SLP(gpd1-1, INPUT, DOWN);
+		PIN_SLP(gpd1-2, INPUT, NONE);
+		PIN_SLP(gpd1-3, INPUT, NONE);
+
+		PIN_SLP(gpf0-0, INPUT, DOWN);
+		PIN_SLP(gpf0-1, INPUT, DOWN);
+		PIN_SLP(gpf0-2, INPUT, DOWN);
+		PIN_SLP(gpf0-3, INPUT, DOWN);
+		PIN_SLP(gpf0-4, OUT0, NONE);
+		PIN_SLP(gpf0-5, OUT0, NONE);
+		PIN_SLP(gpf0-6, INPUT, DOWN);
+		PIN_SLP(gpf0-7, INPUT, DOWN);
+
+		PIN_SLP(gpf1-0, INPUT, DOWN);
+		PIN_SLP(gpf1-1, INPUT, DOWN);
+		PIN_SLP(gpf1-2, INPUT, DOWN);
+		PIN_SLP(gpf1-3, INPUT, DOWN);
+		PIN_SLP(gpf1-4, INPUT, DOWN);
+		PIN_SLP(gpf1-5, INPUT, DOWN);
+		PIN_SLP(gpf1-6, INPUT, DOWN);
+		PIN_SLP(gpf1-7, INPUT, DOWN);
+
+		PIN_SLP(gpf2-0, INPUT, DOWN);
+		PIN_SLP(gpf2-1, INPUT, DOWN);
+		PIN_SLP(gpf2-2, INPUT, DOWN);
+		PIN_SLP(gpf2-3, INPUT, DOWN);
+		PIN_SLP(gpf2-4, INPUT, DOWN);
+		PIN_SLP(gpf2-5, INPUT, DOWN);
+		PIN_SLP(gpf2-6, INPUT, DOWN);
+		PIN_SLP(gpf2-7, INPUT, DOWN);
+
+		PIN_SLP(gpf3-0, INPUT, DOWN);
+		PIN_SLP(gpf3-1, INPUT, DOWN);
+		PIN_SLP(gpf3-2, INPUT, DOWN);
+		PIN_SLP(gpf3-3, INPUT, DOWN);
+		PIN_SLP(gpf3-4, PREV, NONE);
+		PIN_SLP(gpf3-5, OUT0, DOWN);
+
+		PIN_SLP(gpj0-0, INPUT, DOWN);
+		PIN_SLP(gpj0-1, INPUT, DOWN);
+		PIN_SLP(gpj0-2, INPUT, DOWN);
+		PIN_SLP(gpj0-3, OUT0, NONE);
+		PIN_SLP(gpj0-4, INPUT, DOWN);
+		PIN_SLP(gpj0-5, INPUT, DOWN);
+		PIN_SLP(gpj0-6, OUT0, NONE);
+		PIN_SLP(gpj0-7, OUT0, NONE);
+
+		PIN_SLP(gpj1-0, OUT0, NONE);
+		PIN_SLP(gpj1-1, INPUT, DOWN);
+		PIN_SLP(gpj1-2, PREV, NONE);
+		PIN_SLP(gpj1-3, INPUT, DOWN);
+		PIN_SLP(gpj1-4, INPUT, DOWN);
+	};
+};
+
+&pinctrl_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep1>;
+
+	bt_shutdown: bt-shutdown-pins {
+		samsung,pins = "gpl0-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_host_wakeup: bt-host-wakeup-pins {
+		samsung,pins = "gpx2-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_device_wakeup: bt-device-wakeup-pins {
+		samsung,pins = "gpx3-1";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	backlight_reset: backlight-reset-pins {
+		samsung,pins = "gpm0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	gpio_keys: gpio-keys-pins {
+		samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	max77693_irq: max77693-irq-pins {
+		samsung,pins = "gpx1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	max77693_fuel_irq: max77693-fuel-irq-pins {
+		samsung,pins = "gpx2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	sdhci2_cd: sdhci2-cd-irq-pins {
+		samsung,pins = "gpx3-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	s5m8767_dvs: s5m8767-dvs-pins {
+		samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	s5m8767_irq: s5m8767-irq-pins {
+		samsung,pins = "gpx0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	sleep1: sleep-state {
+		PIN_SLP(gpk0-0, PREV, NONE);
+		PIN_SLP(gpk0-1, PREV, NONE);
+		PIN_SLP(gpk0-2, PREV, NONE);
+		PIN_SLP(gpk0-3, PREV, NONE);
+		PIN_SLP(gpk0-4, PREV, NONE);
+		PIN_SLP(gpk0-5, PREV, NONE);
+		PIN_SLP(gpk0-6, PREV, NONE);
+
+		PIN_SLP(gpk1-0, INPUT, DOWN);
+		PIN_SLP(gpk1-1, INPUT, DOWN);
+		PIN_SLP(gpk1-2, INPUT, DOWN);
+		PIN_SLP(gpk1-3, PREV, NONE);
+		PIN_SLP(gpk1-4, PREV, NONE);
+		PIN_SLP(gpk1-5, PREV, NONE);
+		PIN_SLP(gpk1-6, PREV, NONE);
+
+		PIN_SLP(gpk2-0, INPUT, DOWN);
+		PIN_SLP(gpk2-1, INPUT, DOWN);
+		PIN_SLP(gpk2-2, INPUT, DOWN);
+		PIN_SLP(gpk2-3, INPUT, DOWN);
+		PIN_SLP(gpk2-4, INPUT, DOWN);
+		PIN_SLP(gpk2-5, INPUT, DOWN);
+		PIN_SLP(gpk2-6, INPUT, DOWN);
+
+		PIN_SLP(gpk3-0, OUT0, NONE);
+		PIN_SLP(gpk3-1, INPUT, NONE);
+		PIN_SLP(gpk3-2, INPUT, DOWN);
+		PIN_SLP(gpk3-3, INPUT, NONE);
+		PIN_SLP(gpk3-4, INPUT, NONE);
+		PIN_SLP(gpk3-5, INPUT, NONE);
+		PIN_SLP(gpk3-6, INPUT, NONE);
+
+		PIN_SLP(gpl0-0, INPUT, DOWN);
+		PIN_SLP(gpl0-1, INPUT, NONE);
+		PIN_SLP(gpl0-2, INPUT, NONE);
+		PIN_SLP(gpl0-3, INPUT, DOWN);
+		PIN_SLP(gpl0-4, INPUT, DOWN);
+		PIN_SLP(gpl0-6, PREV, NONE);
+
+		PIN_SLP(gpl1-0, INPUT, DOWN);
+		PIN_SLP(gpl1-1, OUT0, NONE);
+		PIN_SLP(gpl2-0, INPUT, DOWN);
+		PIN_SLP(gpl2-1, PREV, NONE);
+		PIN_SLP(gpl2-2, PREV, NONE);
+		PIN_SLP(gpl2-3, INPUT, DOWN);
+		PIN_SLP(gpl2-4, INPUT, DOWN);
+		PIN_SLP(gpl2-5, INPUT, DOWN);
+		PIN_SLP(gpl2-6, INPUT, DOWN);
+		PIN_SLP(gpl2-7, INPUT, DOWN);
+
+		PIN_SLP(gpm0-0, PREV, NONE);
+		PIN_SLP(gpm0-1, OUT0, NONE);
+		PIN_SLP(gpm0-2, INPUT, DOWN);
+		PIN_SLP(gpm0-3, INPUT, DOWN);
+		PIN_SLP(gpm0-4, INPUT, DOWN);
+		PIN_SLP(gpm0-5, INPUT, DOWN);
+		PIN_SLP(gpm0-6, INPUT, DOWN);
+		PIN_SLP(gpm0-7, INPUT, DOWN);
+
+		PIN_SLP(gpm1-0, INPUT, DOWN);
+		PIN_SLP(gpm1-1, INPUT, DOWN);
+		PIN_SLP(gpm1-2, INPUT, NONE);
+		PIN_SLP(gpm1-3, INPUT, NONE);
+		PIN_SLP(gpm1-4, INPUT, NONE);
+		PIN_SLP(gpm1-5, INPUT, NONE);
+		PIN_SLP(gpm1-6, OUT0, NONE);
+
+		PIN_SLP(gpm2-0, INPUT, NONE);
+		PIN_SLP(gpm2-1, INPUT, NONE);
+		PIN_SLP(gpm2-2, OUT0, NONE);
+		PIN_SLP(gpm2-3, INPUT, DOWN);
+		PIN_SLP(gpm2-4, INPUT, DOWN);
+
+		PIN_SLP(gpm3-0, PREV, NONE);
+		PIN_SLP(gpm3-1, PREV, NONE);
+		PIN_SLP(gpm3-2, PREV, NONE);
+		PIN_SLP(gpm3-3, INPUT, DOWN);
+		PIN_SLP(gpm3-4, INPUT, DOWN);
+		PIN_SLP(gpm3-5, PREV, NONE);
+		PIN_SLP(gpm3-6, INPUT, DOWN);
+		PIN_SLP(gpm3-7, OUT0, NONE);
+
+		PIN_SLP(gpm4-0, INPUT, DOWN);
+		PIN_SLP(gpm4-1, INPUT, DOWN);
+		PIN_SLP(gpm4-2, INPUT, DOWN);
+		PIN_SLP(gpm4-3, INPUT, DOWN);
+		PIN_SLP(gpm4-4, PREV, NONE);
+		PIN_SLP(gpm4-5, INPUT, NONE);
+		PIN_SLP(gpm4-6, INPUT, DOWN);
+		PIN_SLP(gpm4-7, INPUT, DOWN);
+
+		PIN_SLP(gpy0-0, INPUT, DOWN);
+		PIN_SLP(gpy0-1, INPUT, DOWN);
+		PIN_SLP(gpy0-2, INPUT, NONE);
+		PIN_SLP(gpy0-3, INPUT, NONE);
+		PIN_SLP(gpy0-4, INPUT, DOWN);
+		PIN_SLP(gpy0-5, INPUT, DOWN);
+
+		PIN_SLP(gpy1-0, INPUT, DOWN);
+		PIN_SLP(gpy1-1, INPUT, DOWN);
+		PIN_SLP(gpy1-2, INPUT, DOWN);
+		PIN_SLP(gpy1-3, INPUT, DOWN);
+
+		PIN_SLP(gpy2-0, PREV, NONE);
+		PIN_SLP(gpy2-1, INPUT, DOWN);
+		PIN_SLP(gpy2-2, INPUT, NONE);
+		PIN_SLP(gpy2-3, INPUT, NONE);
+		PIN_SLP(gpy2-4, INPUT, NONE);
+		PIN_SLP(gpy2-5, INPUT, NONE);
+
+		PIN_SLP(gpy3-0, INPUT, DOWN);
+		PIN_SLP(gpy3-1, INPUT, DOWN);
+		PIN_SLP(gpy3-2, INPUT, DOWN);
+		PIN_SLP(gpy3-3, INPUT, DOWN);
+		PIN_SLP(gpy3-4, INPUT, DOWN);
+		PIN_SLP(gpy3-5, INPUT, DOWN);
+		PIN_SLP(gpy3-6, INPUT, DOWN);
+		PIN_SLP(gpy3-7, INPUT, DOWN);
+
+		PIN_SLP(gpy4-0, INPUT, DOWN);
+		PIN_SLP(gpy4-1, INPUT, DOWN);
+		PIN_SLP(gpy4-2, INPUT, DOWN);
+		PIN_SLP(gpy4-3, INPUT, DOWN);
+		PIN_SLP(gpy4-4, INPUT, DOWN);
+		PIN_SLP(gpy4-5, INPUT, DOWN);
+		PIN_SLP(gpy4-6, INPUT, DOWN);
+		PIN_SLP(gpy4-7, INPUT, DOWN);
+
+		PIN_SLP(gpy5-0, INPUT, DOWN);
+		PIN_SLP(gpy5-1, INPUT, DOWN);
+		PIN_SLP(gpy5-2, INPUT, DOWN);
+		PIN_SLP(gpy5-3, INPUT, DOWN);
+		PIN_SLP(gpy5-4, INPUT, DOWN);
+		PIN_SLP(gpy5-5, INPUT, DOWN);
+		PIN_SLP(gpy5-6, INPUT, DOWN);
+		PIN_SLP(gpy5-7, INPUT, DOWN);
+
+		PIN_SLP(gpy6-0, INPUT, DOWN);
+		PIN_SLP(gpy6-1, INPUT, DOWN);
+		PIN_SLP(gpy6-2, INPUT, DOWN);
+		PIN_SLP(gpy6-3, INPUT, DOWN);
+		PIN_SLP(gpy6-4, INPUT, DOWN);
+		PIN_SLP(gpy6-5, INPUT, DOWN);
+		PIN_SLP(gpy6-6, INPUT, DOWN);
+		PIN_SLP(gpy6-7, INPUT, DOWN);
+	};
+};
+
+&pinctrl_2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep2>;
+
+	sleep2: sleep-state {
+		PIN_SLP(gpz-0, INPUT, DOWN);
+		PIN_SLP(gpz-1, INPUT, DOWN);
+		PIN_SLP(gpz-2, INPUT, DOWN);
+		PIN_SLP(gpz-3, INPUT, DOWN);
+		PIN_SLP(gpz-4, INPUT, DOWN);
+		PIN_SLP(gpz-5, INPUT, DOWN);
+		PIN_SLP(gpz-6, INPUT, DOWN);
+	};
+};
+
+&pinctrl_3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep3>;
+
+	sleep3: sleep-state {
+		PIN_SLP(gpv0-0, INPUT, DOWN);
+		PIN_SLP(gpv0-1, INPUT, DOWN);
+		PIN_SLP(gpv0-2, INPUT, DOWN);
+		PIN_SLP(gpv0-3, INPUT, DOWN);
+		PIN_SLP(gpv0-4, INPUT, DOWN);
+		PIN_SLP(gpv0-5, INPUT, DOWN);
+		PIN_SLP(gpv0-6, INPUT, DOWN);
+		PIN_SLP(gpv0-7, INPUT, DOWN);
+
+		PIN_SLP(gpv1-0, INPUT, DOWN);
+		PIN_SLP(gpv1-1, INPUT, DOWN);
+		PIN_SLP(gpv1-2, INPUT, DOWN);
+		PIN_SLP(gpv1-3, INPUT, DOWN);
+		PIN_SLP(gpv1-4, INPUT, DOWN);
+		PIN_SLP(gpv1-5, INPUT, DOWN);
+		PIN_SLP(gpv1-6, INPUT, DOWN);
+		PIN_SLP(gpv1-7, INPUT, DOWN);
+
+		PIN_SLP(gpv2-0, INPUT, DOWN);
+		PIN_SLP(gpv2-1, INPUT, DOWN);
+		PIN_SLP(gpv2-2, INPUT, DOWN);
+		PIN_SLP(gpv2-3, INPUT, DOWN);
+		PIN_SLP(gpv2-4, INPUT, DOWN);
+		PIN_SLP(gpv2-5, INPUT, DOWN);
+		PIN_SLP(gpv2-6, INPUT, DOWN);
+		PIN_SLP(gpv2-7, INPUT, DOWN);
+
+		PIN_SLP(gpv3-0, INPUT, DOWN);
+		PIN_SLP(gpv3-1, INPUT, DOWN);
+		PIN_SLP(gpv3-2, INPUT, DOWN);
+		PIN_SLP(gpv3-3, INPUT, DOWN);
+		PIN_SLP(gpv3-4, INPUT, DOWN);
+		PIN_SLP(gpv3-5, INPUT, DOWN);
+		PIN_SLP(gpv3-6, INPUT, DOWN);
+		PIN_SLP(gpv3-7, INPUT, DOWN);
+
+		PIN_SLP(gpv4-0, INPUT, DOWN);
+		PIN_SLP(gpv4-1, INPUT, DOWN);
+	};
+};
+
+&pmu_system_controller {
+	assigned-clocks = <&pmu_system_controller 0>;
+	assigned-clock-parents = <&clock CLK_XUSBXTI>;
+};
+
+&pwm {
+	pinctrl-0 = <&pwm1_out>;
+	pinctrl-names = "default";
+	samsung,pwm-outputs = <1>;
+	status = "okay";
+};
+
+/*
+ * The internal RTC does not work; instead, the RTC provided by the
+ * S5M8766 PMIC is used. Disable the RTC to make sure the working
+ * one gets used.
+ *
+ * We add this node to avoid DTB check warnings, as the Exynos4 RTC
+ * requires two clocks, and only one is set up by default.
+ */
+&rtc {
+	clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+	status = "disabled";
+};
+
+&sdhci_2 {
+	bus-width = <4>;
+	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
+	pinctrl-names = "default";
+	vmmc-supply = <&ldo23_reg>;
+	status = "okay";
+};
+
+&sdhci_3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	non-removable;
+	bus-width = <4>;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpx2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&serial_0 {
+	pinctrl-0 = <&uart0_data &uart0_fctl>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt"; /* BCM4334B0 */
+		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
+		pinctrl-names = "default";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&s5m8767_osc S2MPS11_CLK_BT>;
+	};
+};
+
+&serial_1 {
+	status = "okay";
+};
+
+&serial_2 {
+	status = "okay";
+};
+
+&serial_3 {
+	status = "okay";
+};
+
+&tmu {
+	vtmu-supply = <&ldo10_reg>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/samsung/exynos4212.dtsi b/arch/arm/boot/dts/samsung/exynos4212.dtsi
new file mode 100644
index 000000000000..aa984601ee06
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4212.dtsi
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4212 SoC device nodes are listed in this file. Exynos4212
+ * based board files can include this file and provide values for board specific
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4212 SoC. As device tree coverage for Exynos4212 increases, additional
+ * nodes can be added to this file.
+ */
+
+#include "exynos4x12.dtsi"
+
+/ {
+	compatible = "samsung,exynos4212", "samsung,exynos4";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@a00 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0xa00>;
+			clocks = <&clock CLK_ARM_CLK>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+
+		cpu1: cpu@a01 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0xa01>;
+			clocks = <&clock CLK_ARM_CLK>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+	};
+
+	cpu0_opp_table: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <900000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <900000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <925000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <950000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <975000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-700000000 {
+			opp-hz = /bits/ 64 <700000000>;
+			opp-microvolt = <987500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <200000>;
+			opp-suspend;
+		};
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-microvolt = <1037500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1087500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1100000000 {
+			opp-hz = /bits/ 64 <1100000000>;
+			opp-microvolt = <1137500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1187500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1300000000 {
+			opp-hz = /bits/ 64 <1300000000>;
+			opp-microvolt = <1250000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-microvolt = <1287500>;
+			clock-latency-ns = <200000>;
+		};
+		cpu0_opp_1500: opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <1350000>;
+			clock-latency-ns = <200000>;
+			turbo-mode;
+		};
+	};
+};
+
+&clock {
+	compatible = "samsung,exynos4212-clock";
+};
+
+&combiner {
+	samsung,combiner-nr = <18>;
+};
+
+&gic {
+	cpu-offset = <0x8000>;
+};
+
+&pmu {
+	interrupts = <2 2>, <3 2>;
+	interrupt-affinity = <&cpu0>, <&cpu1>;
+	status = "okay";
+};
+
+&pmu_system_controller {
+	compatible = "samsung,exynos4212-pmu", "simple-mfd", "syscon";
+};
diff --git a/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi b/arch/arm/boot/dts/samsung/exynos4412-galaxy-s3.dtsi
index ce87d2ff27aa..54e1a57ae886 100644
--- a/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4412-galaxy-s3.dtsi
@@ -7,6 +7,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos4412-midas.dtsi"
 
 / {
@@ -15,7 +16,7 @@
 		i2c10 = &i2c_cm36651;
 	};
 
-	aat1290 {
+	led-controller {
 		compatible = "skyworks,aat1290";
 		flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
 		enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
@@ -25,15 +26,16 @@
 		pinctrl-1 = <&camera_flash_host>;
 		pinctrl-2 = <&camera_flash_isp>;
 
-		flash-led {
-			label = "flash";
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
 			led-max-microamp = <520833>;
 			flash-max-microamp = <1012500>;
 			flash-max-timeout-us = <1940000>;
 		};
 	};
 
-	lcd_vdd3_reg: voltage-regulator-6 {
+	lcd_vdd3_reg: voltage-regulator-10 {
 		compatible = "regulator-fixed";
 		regulator-name = "LCD_VDD_2.2V";
 		regulator-min-microvolt = <2200000>;
@@ -42,7 +44,7 @@
 		enable-active-high;
 	};
 
-	ps_als_reg: voltage-regulator-7 {
+	ps_als_reg: voltage-regulator-11 {
 		compatible = "regulator-fixed";
 		regulator-name = "LED_A_3.0V";
 		regulator-min-microvolt = <3000000>;
@@ -53,13 +55,13 @@
 
 	i2c_ak8975: i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		i2c-gpio,delay-us = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "okay";
 
-		ak8975@c {
+		magnetometer@c {
 			compatible = "asahi-kasei,ak8975";
 			reg = <0x0c>;
 			gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>;
@@ -68,12 +70,13 @@
 
 	i2c_cm36651: i2c-gpio-2 {
 		compatible = "i2c-gpio";
-		gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>;
+		sda-gpios = <&gpf0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpf0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		i2c-gpio,delay-us = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cm36651@18 {
+		light-sensor@18 {
 			compatible = "capella,cm36651";
 			reg = <0x18>;
 			interrupt-parent = <&gpx0>;
@@ -106,7 +109,7 @@
 		vdd3-supply = <&lcd_vdd3_reg>;
 		vci-supply = <&ldo25_reg>;
 		reset-gpios = <&gpf2 1 GPIO_ACTIVE_HIGH>;
-		power-on-delay= <50>;
+		power-on-delay = <50>;
 		reset-delay = <100>;
 		init-delay = <100>;
 		flip-horizontal;
@@ -131,7 +134,7 @@
 };
 
 &i2c_3 {
-	mms114-touchscreen@48 {
+	touchscreen@48 {
 		compatible = "melfas,mms114";
 		reg = <0x48>;
 		interrupt-parent = <&gpm2>;
@@ -150,13 +153,13 @@
 };
 
 &pinctrl_0 {
-	camera_flash_host: camera-flash-host {
+	camera_flash_host: camera-flash-host-pins {
 		samsung,pins = "gpj1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-val = <0>;
 	};
 
-	camera_flash_isp: camera-flash-isp {
+	camera_flash_isp: camera-flash-isp-pins {
 		samsung,pins = "gpj1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-val = <1>;
@@ -168,3 +171,45 @@
 	vdda-supply = <&ldo17_reg>;
 	status = "okay";
 };
+
+&sound {
+	audio-routing = "HP", "HPOUT1L",
+			"HP", "HPOUT1R",
+
+			"SPK", "SPKOUTLN",
+			"SPK", "SPKOUTLP",
+			"SPK", "SPKOUTRN",
+			"SPK", "SPKOUTRP",
+
+			"RCV", "HPOUT2N",
+			"RCV", "HPOUT2P",
+
+			"HDMI", "LINEOUT1N",
+			"HDMI", "LINEOUT1P",
+
+			"LINE", "LINEOUT2N",
+			"LINE", "LINEOUT2P",
+
+			"IN1LP", "MICBIAS1",
+			"IN1LN", "MICBIAS1",
+			"Main Mic", "MICBIAS1",
+
+			"IN1RP", "Sub Mic",
+			"IN1RN", "Sub Mic",
+
+			"IN2LP:VXRN", "MICBIAS2",
+			"Headset Mic", "MICBIAS2",
+
+			"IN2RN", "FM In",
+			"IN2RP:VXRP", "FM In";
+};
+
+&submic_bias_reg {
+	gpio = <&gpf2 0 GPIO_ACTIVE_HIGH>;
+	enable-active-high;
+};
+
+&touchkey_reg {
+	gpio = <&gpm0 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/exynos4412-i9300.dts b/arch/arm/boot/dts/samsung/exynos4412-i9300.dts
index f8125a945f8d..61aca5798f38 100644
--- a/arch/arm/boot/dts/exynos4412-i9300.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-i9300.dts
@@ -12,11 +12,16 @@
 / {
 	model = "Samsung Galaxy S3 (GT-I9300) based on Exynos4412";
 	compatible = "samsung,i9300", "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
+	chassis-type = "handset";
 
 	/* bootargs are passed in by bootloader */
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x40000000>;
+		reg = <0x40000000 0x40000000>;
 	};
 };
+
+&sound {
+	fm-sel-gpios = <&gpl0 3 GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm/boot/dts/exynos4412-i9305.dts b/arch/arm/boot/dts/samsung/exynos4412-i9305.dts
index 54a2a55dbf70..77083f1a8273 100644
--- a/arch/arm/boot/dts/exynos4412-i9305.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-i9305.dts
@@ -5,12 +5,13 @@
 / {
 	model = "Samsung Galaxy S3 (GT-I9305) based on Exynos4412";
 	compatible = "samsung,i9305", "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
+	chassis-type = "handset";
 
 	/* bootargs are passed in by bootloader */
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x80000000>;
+		reg = <0x40000000 0x80000000>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/samsung/exynos4412-itop-elite.dts
index f6d0a5f5d339..ded232b04e0d 100644
--- a/arch/arm/boot/dts/exynos4412-itop-elite.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-itop-elite.dts
@@ -11,6 +11,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/sound/samsung-i2s.h>
 #include "exynos4412-itop-scp-core.dtsi"
@@ -19,6 +20,10 @@
 	model = "TOPEET iTop 4412 Elite board based on Exynos4412";
 	compatible = "topeet,itop4412-elite", "samsung,exynos4412", "samsung,exynos4";
 
+	aliases {
+		mmc1 = &sdhci_2;
+	};
+
 	chosen {
 		bootargs = "root=/dev/mmcblk0p2 rw rootfstype=ext4 rootdelay=1 rootwait";
 		stdout-path = "serial2:115200n8";
@@ -28,7 +33,8 @@
 		compatible = "gpio-leds";
 
 		led2 {
-			label = "red:system";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
@@ -36,6 +42,7 @@
 
 		led3 {
 			label = "red:user";
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
@@ -44,31 +51,31 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "GPIO Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpx1 1 GPIO_ACTIVE_LOW>;
 		};
 
-		back {
+		key-back {
 			label = "GPIO Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
 		};
 
-		sleep {
+		key-sleep {
 			label = "GPIO Key Sleep";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
 		};
 
-		vol-up {
+		key-vol-up {
 			label = "GPIO Key Vol+";
 			linux,code = <KEY_UP>;
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 		};
 
-		vol-down {
+		key-vol-down {
 			label = "GPIO Key Vol-";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
@@ -175,11 +182,11 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	codec: wm8960@1a {
+	codec: audio-codec@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
 		clocks = <&pmu_system_controller 0>;
-		clock-names = "MCLK1";
+		clock-names = "mclk";
 		wlf,shared-lrclk;
 		#sound-dai-cells = <0>;
 	};
@@ -192,7 +199,7 @@
 };
 
 &pinctrl_1 {
-	ether-reset {
+	ether-reset-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -211,7 +218,7 @@
 	bus-width = <4>;
 	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
 	pinctrl-names = "default";
-	cd-gpio = <&gpx0 7 GPIO_ACTIVE_LOW>;
+	cd-gpios = <&gpx0 7 GPIO_ACTIVE_LOW>;
 	cap-sd-highspeed;
 	vmmc-supply = <&ldo23_reg>;
 	vqmmc-supply = <&ldo17_reg>;
diff --git a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi b/arch/arm/boot/dts/samsung/exynos4412-itop-scp-core.dtsi
index dfceb155b3a7..7bc6968af9c3 100644
--- a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4412-itop-scp-core.dtsi
@@ -23,9 +23,13 @@
 		reg = <0x40000000 0x40000000>;
 	};
 
+	aliases {
+		mmc0 = &mshc_0;
+	};
+
 	firmware@203f000 {
 		compatible = "samsung,secure-firmware";
-		reg = <0x0203F000 0x1000>;
+		reg = <0x0203f000 0x1000>;
 	};
 
 	fixed-rate-clocks {
@@ -134,7 +138,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	s5m8767: s5m8767-pmic@66 {
+	s5m8767: pmic@66 {
 		compatible = "samsung,s5m8767-pmic";
 		reg = <0x66>;
 
@@ -163,6 +167,7 @@
 						 <1025000>, <950000>,
 						 <918750>, <900000>,
 						 <875000>, <831250>;
+		wakeup-source;
 
 		regulators {
 			ldo1_reg: LDO1 {
@@ -475,6 +480,7 @@
 	vmmc-supply = <&buck9_reg>;
 	broken-cd;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <2 3>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
@@ -483,7 +489,7 @@
 };
 
 &pinctrl_1 {
-	hsic_reset: hsic-reset {
+	hsic_reset: hsic-reset-pins {
 		samsung,pins = "gpm2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/samsung/exynos4412-midas.dtsi
index 83be3a797411..3d5aace668dc 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4412-midas.dtsi
@@ -12,10 +12,12 @@
 /dts-v1/;
 #include "exynos4412.dtsi"
 #include "exynos4412-ppmu-common.dtsi"
+
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/maxim,max77686.h>
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 / {
 	compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
@@ -23,6 +25,9 @@
 	aliases {
 		i2c11 = &i2c_max77693;
 		i2c12 = &i2c_max77693_fuel;
+		mmc0 = &mshc_0;
+		mmc2 = &sdhci_2;
+		mmc3 = &sdhci_3;
 	};
 
 	chosen {
@@ -31,17 +36,17 @@
 
 	firmware@204f000 {
 		compatible = "samsung,secure-firmware";
-		reg = <0x0204F000 0x1000>;
+		reg = <0x0204f000 0x1000>;
 	};
 
 	fixed-rate-clocks {
 		xxti {
-			compatible = "samsung,clock-xxti", "fixed-clock";
+			compatible = "samsung,clock-xxti";
 			clock-frequency = <0>;
 		};
 
 		xusbxti {
-			compatible = "samsung,clock-xusbxti", "fixed-clock";
+			compatible = "samsung,clock-xusbxti";
 			clock-frequency = <24000000>;
 		};
 	};
@@ -92,6 +97,39 @@
 		enable-active-high;
 	};
 
+	touchkey_reg: voltage-regulator-6 {
+		compatible = "regulator-fixed";
+		regulator-name = "LED_VDD_3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	vbatt_reg: voltage-regulator-7 {
+		compatible = "regulator-fixed";
+		regulator-name = "VBATT";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	mic_bias_reg: voltage-regulator-8 {
+		compatible = "regulator-fixed";
+		regulator-name = "MICBIAS_LDO_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpf1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	submic_bias_reg: voltage-regulator-9 {
+		compatible = "regulator-fixed";
+		regulator-name = "SUB_MICBIAS_LDO_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -99,21 +137,21 @@
 
 		key-down {
 			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
-			linux,code = <114>;
+			linux,code = <KEY_VOLUMEDOWN>;
 			label = "volume down";
 			debounce-interval = <10>;
 		};
 
 		key-up {
 			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
-			linux,code = <115>;
+			linux,code = <KEY_VOLUMEUP>;
 			label = "volume up";
 			debounce-interval = <10>;
 		};
 
 		key-power {
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
-			linux,code = <116>;
+			linux,code = <KEY_POWER>;
 			label = "power";
 			debounce-interval = <10>;
 			wakeup-source;
@@ -121,7 +159,7 @@
 
 		key-ok {
 			gpios = <&gpx0 1 GPIO_ACTIVE_LOW>;
-			linux,code = <139>;
+			linux,code = <KEY_OK>;
 			label = "ok";
 			debounce-interval = <10>;
 			wakeup-source;
@@ -130,20 +168,52 @@
 
 	i2c_max77693: i2c-gpio-1 {
 		compatible = "i2c-gpio";
-		gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		i2c-gpio,delay-us = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "okay";
 
-		max77693@66 {
+		pmic@66 {
 			compatible = "maxim,max77693";
 			interrupt-parent = <&gpx1>;
-			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&max77693_irq>;
 			reg = <0x66>;
 
+			muic {
+				compatible = "maxim,max77693-muic";
+
+				connector {
+					compatible = "samsung,usb-connector-11pin",
+						     "usb-b-connector";
+					label = "micro-USB";
+					type = "micro";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							muic_to_usb: endpoint {
+								remote-endpoint = <&usb_to_muic>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							muic_to_mhl: endpoint {
+								remote-endpoint = <&mhl_to_muic>;
+							};
+						};
+					};
+				};
+			};
+
 			regulators {
 				esafeout1_reg: ESAFEOUT1 {
 					regulator-name = "ESAFEOUT1";
@@ -158,7 +228,7 @@
 				};
 			};
 
-			max77693_haptic {
+			motor-driver {
 				compatible = "maxim,max77693-haptic";
 				haptic-supply = <&ldo26_reg>;
 				pwms = <&pwm 0 38022 0>;
@@ -178,16 +248,16 @@
 
 	i2c_max77693_fuel: i2c-gpio-3 {
 		compatible = "i2c-gpio";
-		gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>, <&gpf1 4 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpf1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpf1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		i2c-gpio,delay-us = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "okay";
 
-		max77693-fuel-gauge@36 {
+		fuel-gauge@36 {
 			compatible = "maxim,max17047";
 			interrupt-parent = <&gpx2>;
-			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&max77693_fuel_irq>;
 			reg = <0x36>;
@@ -197,16 +267,35 @@
 		};
 	};
 
+	i2c-gpio-4 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "cypress,midas-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&touchkey_reg>;
+			vcc-supply = <&ldo5_reg>;
+			interrupt-parent = <&gpj0>;
+			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+			linux,keycodes = <KEY_BACK KEY_MENU>;
+		};
+	};
+
 	i2c-mhl {
 		compatible = "i2c-gpio";
-		gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&gpf0 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpf0 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		i2c-gpio,delay-us = <100>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		pinctrl-0 = <&i2c_mhl_bus>;
 		pinctrl-names = "default";
-		status = "okay";
 
 		sii9234: hdmi-bridge@39 {
 			compatible = "sil,sii9234";
@@ -219,9 +308,24 @@
 			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			reg = <0x39>;
 
-			port {
-				mhl_to_hdmi: endpoint {
-					remote-endpoint = <&hdmi_to_mhl>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					mhl_to_hdmi: endpoint {
+						remote-endpoint = <&hdmi_to_mhl>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					mhl_to_muic: endpoint {
+						remote-endpoint = <&muic_to_mhl>;
+					};
 				};
 			};
 		};
@@ -234,16 +338,18 @@
 		clock-names = "ext_clock";
 	};
 
-	sound {
-		compatible = "samsung,trats2-audio";
-		samsung,i2s-controller = <&i2s0>;
-		samsung,model = "Trats2";
-		samsung,audio-codec = <&wm1811>;
-		samsung,audio-routing =
-			"SPK", "SPKOUTLN",
-			"SPK", "SPKOUTLP",
-			"SPK", "SPKOUTRN",
-			"SPK", "SPKOUTRP";
+	sound: sound {
+		compatible = "samsung,midas-audio";
+		model = "Midas";
+		mic-bias-supply = <&mic_bias_reg>;
+		submic-bias-supply = <&submic_bias_reg>;
+
+		cpu {
+			sound-dai = <&i2s0 0>;
+		};
+		codec {
+			sound-dai = <&wm1811>;
+		};
 	};
 
 	thermistor-ap {
@@ -261,25 +367,6 @@
 		pulldown-ohm = <100000>; /* 100K */
 		io-channels = <&adc 2>;  /* Battery temperature */
 	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			cooling-maps {
-				map0 {
-				     /* Corresponds to 800MHz at freq_table */
-				     cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
-						      <&cpu2 7 7>, <&cpu3 7 7>;
-				};
-				map1 {
-				     /* Corresponds to 200MHz at freq_table */
-				     cooling-device = <&cpu0 13 13>,
-						      <&cpu1 13 13>,
-						      <&cpu2 13 13>,
-						      <&cpu3 13 13>;
-			       };
-		       };
-		};
-	};
 };
 
 &adc {
@@ -348,6 +435,21 @@
 	cpu0-supply = <&buck2_reg>;
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+					 <&cpu2 7 7>, <&cpu3 7 7>;
+		};
+		map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+					 <&cpu2 13 13>, <&cpu3 13 13>;
+		};
+	};
+};
+
 &csis_0 {
 	status = "okay";
 	vddcore-supply = <&ldo8_reg>;
@@ -438,8 +540,7 @@
 	pinctrl-0 = <&fimc_is_uart>;
 	pinctrl-names = "default";
 	status = "okay";
-
-	};
+};
 
 &fimc_lite_0 {
 	status = "okay";
@@ -484,8 +585,16 @@
 &hsotg {
 	vusb_d-supply = <&ldo15_reg>;
 	vusb_a-supply = <&ldo12_reg>;
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	role-switch-default-mode = "peripheral";
+	usb-role-switch;
 	status = "okay";
+
+	port {
+		usb_to_muic: endpoint {
+			remote-endpoint = <&muic_to_usb>;
+		};
+	};
 };
 
 &i2c_0 {
@@ -496,7 +605,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	s5c73m3: s5c73m3@3c {
+	s5c73m3: image-sensor@3c {
 		compatible = "samsung,s5c73m3";
 		reg = <0x3c>;
 		xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
@@ -523,7 +632,7 @@
 	pinctrl-0 = <&fimc_is_i2c1>;
 	pinctrl-names = "default";
 
-	s5k6a3@10 {
+	image-sensor@10 {
 		compatible = "samsung,s5k6a3";
 		reg = <0x10>;
 		svdda-supply = <&cam_io_reg>;
@@ -533,8 +642,7 @@
 		/* CAM_B_CLKOUT */
 		clocks = <&camera 1>;
 		clock-names = "extclk";
-		samsung,camclk-out = <1>;
-		gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpm1 6 GPIO_ACTIVE_LOW>;
 
 		port {
 			is_s5k6a3_ep: endpoint {
@@ -562,14 +670,40 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	wm1811: wm1811@1a {
+	wm1811: audio-codec@1a {
 		compatible = "wlf,wm1811";
 		reg = <0x1a>;
-		clocks = <&pmu_system_controller 0>;
-		clock-names = "MCLK1";
-		DCVDD-supply = <&ldo3_reg>;
+		clocks = <&pmu_system_controller 0>,
+			<&max77686 MAX77686_CLK_PMIC>;
+		clock-names = "MCLK1", "MCLK2";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpx3>;
+		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		#sound-dai-cells = <0>;
+
+		wlf,gpio-cfg = <0x3 0x0 0x0 0x0 0x0 0x0
+			0x0 0x8000 0x0 0x0 0x0>;
+		wlf,micbias-cfg = <0x2f 0x2b>;
+
+		wlf,lineout1-feedback;
+		wlf,lineout1-se;
+		wlf,lineout2-se;
+		wlf,ldoena-always-driven;
+
+		AVDD2-supply = <&vbatt_reg>;
 		DBVDD1-supply = <&ldo3_reg>;
-		wlf,ldo1ena = <&gpj0 4 0>;
+		DBVDD2-supply = <&vbatt_reg>;
+		DBVDD3-supply = <&vbatt_reg>;
+		DCVDD-supply = <&ldo3_reg>;
+		CPVDD-supply = <&vbatt_reg>;
+		SPKVDD1-supply = <&vbatt_reg>;
+		SPKVDD2-supply = <&vbatt_reg>;
+		wlf,ldo1ena-gpios = <&gpj0 4 GPIO_ACTIVE_HIGH>;
+		wlf,ldo2ena-gpios = <&gpj0 4 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -585,12 +719,13 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	max77686: max77686_pmic@9 {
+	max77686: pmic@9 {
 		compatible = "maxim,max77686";
 		interrupt-parent = <&gpx0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-0 = <&max77686_irq>;
 		pinctrl-names = "default";
+		wakeup-source;
 		reg = <0x09>;
 		#clock-cells = <1>;
 
@@ -791,7 +926,7 @@
 			};
 
 			buck1_reg: BUCK1 {
-				regulator-name = "vdd_mif";
+				regulator-name = "VDD_MIF";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-always-on;
@@ -802,7 +937,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "vdd_arm";
+				regulator-name = "VDD_ARM";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
@@ -813,7 +948,7 @@
 			};
 
 			buck3_reg: BUCK3 {
-				regulator-name = "vdd_int";
+				regulator-name = "VDD_INT";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <1150000>;
 				regulator-always-on;
@@ -824,7 +959,7 @@
 			};
 
 			buck4_reg: BUCK4 {
-				regulator-name = "vdd_g3d";
+				regulator-name = "VDD_G3D";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <1150000>;
 				regulator-boot-on;
@@ -893,6 +1028,7 @@
 	samsung,dw-mshc-ciu-div = <0>;
 	samsung,dw-mshc-sdr-timing = <2 3>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
+	mmc-ddr-1_8v;
 	pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 	pinctrl-names = "default";
 	status = "okay";
@@ -902,26 +1038,26 @@
 
 &pmu_system_controller {
 	assigned-clocks = <&pmu_system_controller 0>;
-	assigned-clock-parents =  <&clock CLK_XUSBXTI>;
+	assigned-clock-parents = <&clock CLK_XUSBXTI>;
 };
 
 &pinctrl_0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep0>;
 
-	mhl_int: mhl-int {
+	mhl_int: mhl-int-pins {
 		samsung,pins = "gpf3-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	i2c_mhl_bus: i2c-mhl-bus {
+	i2c_mhl_bus: i2c-mhl-bus-pins {
 		samsung,pins = "gpf0-4", "gpf0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	sleep0: sleep-states {
+	sleep0: sleep-state {
 		PIN_SLP(gpa0-0, INPUT, NONE);
 		PIN_SLP(gpa0-1, OUT0, NONE);
 		PIN_SLP(gpa0-2, INPUT, NONE);
@@ -1024,37 +1160,52 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep1>;
 
-	gpio_keys: gpio-keys {
+	gpio_keys: gpio-keys-pins {
 		samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77686_irq: max77686-irq {
+	bt_shutdown: bt-shutdown-pins {
+		samsung,pins = "gpl0-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_host_wakeup: bt-host-wakeup-pins {
+		samsung,pins = "gpx2-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_device_wakeup: bt-device-wakeup-pins {
+		samsung,pins = "gpx3-1";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77693_irq: max77693-irq {
+	max77693_irq: max77693-irq-pins {
 		samsung,pins = "gpx1-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77693_fuel_irq: max77693-fuel-irq {
+	max77693_fuel_irq: max77693-fuel-irq-pins {
 		samsung,pins = "gpx2-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	sdhci2_cd: sdhci2-cd-irq {
+	sdhci2_cd: sdhci2-cd-irq-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	sleep1: sleep-states {
+	sleep1: sleep-state {
 		PIN_SLP(gpk0-0, PREV, NONE);
 		PIN_SLP(gpk0-1, PREV, NONE);
 		PIN_SLP(gpk0-2, OUT0, NONE);
@@ -1207,7 +1358,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep2>;
 
-	sleep2: sleep-states {
+	sleep2: sleep-state {
 		PIN_SLP(gpz-0, INPUT, DOWN);
 		PIN_SLP(gpz-1, INPUT, DOWN);
 		PIN_SLP(gpz-2, INPUT, DOWN);
@@ -1222,7 +1373,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep3>;
 
-	sleep3: sleep-states {
+	sleep3: sleep-state {
 		PIN_SLP(gpv0-0, INPUT, DOWN);
 		PIN_SLP(gpv0-1, INPUT, DOWN);
 		PIN_SLP(gpv0-2, INPUT, DOWN);
@@ -1306,7 +1457,20 @@
 };
 
 &serial_0 {
+	pinctrl-0 = <&uart0_data &uart0_fctl>;
+	pinctrl-names = "default";
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
+		pinctrl-names = "default";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&max77686 MAX77686_CLK_PMIC>;
+	};
 };
 
 &serial_1 {
@@ -1327,7 +1491,7 @@
 	cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	s5c73m3_spi: s5c73m3@0 {
+	s5c73m3_spi: image-sensor@0 {
 		compatible = "samsung,s5c73m3";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/exynos4412-n710x.dts b/arch/arm/boot/dts/samsung/exynos4412-n710x.dts
index fe2bfd76cc4e..0a151437fc73 100644
--- a/arch/arm/boot/dts/exynos4412-n710x.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-n710x.dts
@@ -5,15 +5,16 @@
 / {
 	compatible = "samsung,n710x", "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
 	model = "Samsung Galaxy Note 2 (GT-N7100, GT-N7105) based on Exynos4412";
+	chassis-type = "handset";
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x80000000>;
+		reg = <0x40000000 0x80000000>;
 	};
 
 	/* bootargs are passed in by bootloader */
 
-	cam_vdda_reg: voltage-regulator-6 {
+	cam_vdda_reg: voltage-regulator-10 {
 		compatible = "regulator-fixed";
 		regulator-name = "CAM_SENSOR_CORE_1.2V";
 		regulator-min-microvolt = <1200000>;
@@ -45,13 +46,13 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	mms152-touchscreen@48 {
+	touchscreen@48 {
 		compatible = "melfas,mms152";
 		reg = <0x48>;
 		interrupt-parent = <&gpm2>;
 		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
-		x-size = <720>;
-		y-size = <1280>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
 		avdd-supply = <&ldo23_reg>;
 		vdd-supply = <&ldo24_reg>;
 	};
@@ -73,3 +74,42 @@
 	vdda-supply = <&cam_vdda_reg>;
 	status = "okay";
 };
+
+&sound {
+	audio-routing = "HP", "HPOUT1L",
+			"HP", "HPOUT1R",
+
+			"SPK", "SPKOUTLN",
+			"SPK", "SPKOUTLP",
+
+			"RCV", "HPOUT2N",
+			"RCV", "HPOUT2P",
+
+			"HDMI", "LINEOUT1N",
+			"HDMI", "LINEOUT1P",
+
+			"LINE", "LINEOUT2N",
+			"LINE", "LINEOUT2P",
+
+			"IN1LP", "MICBIAS2",
+			"IN1LN", "MICBIAS2",
+			"Headset Mic", "MICBIAS2",
+
+			"IN1RP", "Sub Mic",
+			"IN1RN", "Sub Mic",
+
+			"IN2LP:VXRN", "Main Mic",
+			"IN2LN", "Main Mic",
+
+			"IN2RN", "FM In",
+			"IN2RP:VXRP", "FM In";
+};
+
+&submic_bias_reg {
+	regulator-always-on;
+};
+
+&touchkey_reg {
+	gpio = <&gpm0 5 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/samsung/exynos4412-odroid-common.dtsi
index ea55f377d17c..93ddbd4b0a18 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4412-odroid-common.dtsi
@@ -2,7 +2,7 @@
 /*
  * Common definition for Hardkernel's Exynos4412 based ODROID-X/X2/U2/U3 boards
  * device tree source
-*/
+ */
 
 #include <dt-bindings/sound/samsung-i2s.h>
 #include <dt-bindings/input/input.h>
@@ -13,21 +13,26 @@
 #include "exynos-mfc-reserved-memory.dtsi"
 
 / {
+	aliases {
+		mmc0 = &mshc_0;
+		mmc2 = &sdhci_2;
+	};
+
 	chosen {
 		stdout-path = &serial_1;
 	};
 
 	firmware@204f000 {
 		compatible = "samsung,secure-firmware";
-		reg = <0x0204F000 0x1000>;
+		reg = <0x0204f000 0x1000>;
 	};
 
-	gpio_keys {
+	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_power_key>;
 
-		power_key {
+		power-key {
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "power key";
@@ -66,25 +71,6 @@
 			clock-frequency = <24000000>;
 		};
 	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			cooling-maps {
-				cooling_map0: map0 {
-				     /* Corresponds to 800MHz at freq_table */
-				     cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
-						      <&cpu2 7 7>, <&cpu3 7 7>;
-				};
-				cooling_map1: map1 {
-				     /* Corresponds to 200MHz at freq_table */
-				     cooling-device = <&cpu0 13 13>,
-						      <&cpu1 13 13>,
-						      <&cpu2 13 13>,
-						      <&cpu3 13 13>;
-			       };
-		       };
-		};
-	};
 };
 
 &bus_dmc {
@@ -136,11 +122,10 @@
 
 &camera {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <>;
 };
 
 &clock {
+	clocks = <&clock CLK_XUSBXTI>;
 	assigned-clocks = <&clock CLK_FOUT_EPLL>;
 	assigned-clock-rates = <45158401>;
 };
@@ -165,25 +150,49 @@
 	cpu0-supply = <&buck2_reg>;
 };
 
+&cpu0_opp_table {
+	opp-1000000000 {
+		opp-suspend;
+	};
+	opp-800000000 {
+		/delete-property/opp-suspend;
+	};
+};
+
+&cpu_thermal {
+	cooling-maps {
+		cooling_map0: map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+					 <&cpu2 7 7>, <&cpu3 7 7>;
+		};
+		cooling_map1: map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+					 <&cpu2 13 13>, <&cpu3 13 13>;
+		};
+	};
+};
+
 &pinctrl_1 {
-	gpio_power_key: power_key {
+	gpio_power_key: power-key-pins {
 		samsung,pins = "gpx1-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	emmc_rstn: emmc-rstn {
+	emmc_rstn: emmc-rstn-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
@@ -250,7 +259,6 @@
 };
 
 &hsotg {
-	dr_mode = "peripheral";
 	status = "okay";
 	vusb_d-supply = <&ldo15_reg>;
 	vusb_a-supply = <&ldo12_reg>;
@@ -261,22 +269,23 @@
 	samsung,i2c-max-bus-freq = <400000>;
 	status = "okay";
 
-	usb3503: usb3503@8 {
+	usb3503: usb-hub@8 {
 		compatible = "smsc,usb3503";
 		reg = <0x08>;
 
 		intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
 		connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
 		initial-mode = <1>;
 	};
 
 	max77686: pmic@9 {
 		compatible = "maxim,max77686";
 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_NONE>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77686_irq>;
+		wakeup-source;
 		reg = <0x09>;
 		#clock-cells = <1>;
 
@@ -421,7 +430,7 @@
 			};
 
 			buck1_reg: BUCK1 {
-				regulator-name = "vdd_mif";
+				regulator-name = "VDD_MIF";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-always-on;
@@ -429,7 +438,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "vdd_arm";
+				regulator-name = "VDD_ARM";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
@@ -437,7 +446,7 @@
 			};
 
 			buck3_reg: BUCK3 {
-				regulator-name = "vdd_int";
+				regulator-name = "VDD_INT";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1050000>;
 				regulator-always-on;
@@ -445,7 +454,7 @@
 			};
 
 			buck4_reg: BUCK4 {
-				regulator-name = "vdd_g3d";
+				regulator-name = "VDD_G3D";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-microvolt-offset = <50000>;
@@ -487,7 +496,7 @@
 
 &i2c_1 {
 	status = "okay";
-	max98090: max98090@10 {
+	max98090: audio-codec@10 {
 		compatible = "maxim,max98090";
 		reg = <0x10>;
 		interrupt-parent = <&gpx0>;
@@ -527,6 +536,7 @@
 
 	broken-cd;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <2 3>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/samsung/exynos4412-odroidu3.dts
index 8ff243ba4542..b1b0916b1505 100644
--- a/arch/arm/boot/dts/exynos4412-odroidu3.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-odroidu3.dts
@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos4412-odroid-common.dtsi"
 #include "exynos4412-prime.dtsi"
 
@@ -16,15 +17,29 @@
 	model = "Hardkernel ODROID-U3 board based on Exynos4412";
 	compatible = "hardkernel,odroid-u3", "samsung,exynos4412", "samsung,exynos4";
 
+	aliases {
+		ethernet = &ethernet;
+	};
+
 	memory@40000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x7FF00000>;
+		reg = <0x40000000 0x7ff00000>;
+	};
+
+	vbus_otg_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VBUS_VDD_5.0V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpl2 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 		led1 {
-			label = "led1:heart";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&gpc1 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
@@ -37,31 +52,6 @@
 		#cooling-cells = <2>;
 		cooling-levels = <0 102 170 230>;
 	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			cooling-maps {
-				map0 {
-				     trip = <&cpu_alert1>;
-				     cooling-device = <&cpu0 9 9>, <&cpu1 9 9>,
-						      <&cpu2 9 9>, <&cpu3 9 9>,
-						      <&fan0 1 2>;
-				};
-				map1 {
-				     trip = <&cpu_alert2>;
-				     cooling-device = <&cpu0 15 15>,
-						      <&cpu1 15 15>,
-						      <&cpu2 15 15>,
-						      <&cpu3 15 15>,
-						      <&fan0 2 3>;
-				};
-				map2 {
-				     trip = <&cpu_alert0>;
-				     cooling-device = <&fan0 0 1>;
-				};
-			};
-		};
-	};
 };
 
 &adc {
@@ -76,6 +66,27 @@
 	regulator-max-microvolt = <3300000>;
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			trip = <&cpu_alert1>;
+			cooling-device = <&cpu0 9 9>, <&cpu1 9 9>,
+					 <&cpu2 9 9>, <&cpu3 9 9>,
+					 <&fan0 1 2>;
+		};
+		map1 {
+			trip = <&cpu_alert2>;
+			cooling-device = <&cpu0 15 15>, <&cpu1 15 15>,
+					 <&cpu2 15 15>, <&cpu3 15 15>,
+					 <&fan0 2 3>;
+		};
+		map2 {
+			trip = <&cpu_alert0>;
+			cooling-device = <&fan0 0 1>;
+		};
+	};
+};
+
 &hdmicec {
 	needs-hpd;
 };
@@ -105,8 +116,21 @@
 };
 
 &ehci {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	phys = <&exynos_usbphy 2>, <&exynos_usbphy 3>;
 	phy-names = "hsic0", "hsic1";
+
+	ethernet: ethernet@2 {
+		compatible = "usb424,9730";
+		reg = <2>;
+		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
+	};
+};
+
+&hsotg {
+	dr_mode = "otg";
+	vbus-supply = <&vbus_otg_reg>;
 };
 
 &sound {
@@ -114,13 +138,12 @@
 	samsung,audio-widgets =
 		"Headphone", "Headphone Jack",
 		"Speakers", "Speakers";
-	samsung,audio-routing =
-		"Headphone Jack", "HPL",
-		"Headphone Jack", "HPR",
-		"Headphone Jack", "MICBIAS",
-		"IN1", "Headphone Jack",
-		"Speakers", "SPKL",
-		"Speakers", "SPKR";
+	audio-routing = "Headphone Jack", "HPL",
+			"Headphone Jack", "HPR",
+			"Headphone Jack", "MICBIAS",
+			"IN1", "Headphone Jack",
+			"Speakers", "SPKL",
+			"Speakers", "SPKR";
 };
 
 &spi_1 {
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/samsung/exynos4412-odroidx.dts
index 3ea2a0101e80..0eb8a2680a20 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-odroidx.dts
@@ -9,46 +9,41 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos4412-odroid-common.dtsi"
 
 / {
 	model = "Hardkernel ODROID-X board based on Exynos4412";
 	compatible = "hardkernel,odroid-x", "samsung,exynos4412", "samsung,exynos4";
 
+	aliases {
+		ethernet = &ethernet;
+	};
+
 	memory@40000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x3FF00000>;
+		reg = <0x40000000 0x3ff00000>;
 	};
 
 	leds {
 		compatible = "gpio-leds";
 		led1 {
-			label = "led1:heart";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&gpc1 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 		led2 {
 			label = "led2:mmc0";
+			function = LED_FUNCTION_DISK_ACTIVITY;
 			gpios = <&gpc1 2 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "mmc0";
 		};
 	};
 
-	gpio_keys {
-		pinctrl-0 = <&gpio_power_key &gpio_home_key>;
-
-		home_key {
-			gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_HOME>;
-			label = "home key";
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	regulator_p3v3 {
+	regulator-1 {
 		compatible = "regulator-fixed";
 		regulator-name = "p3v3_en";
 		regulator-min-microvolt = <3300000>;
@@ -72,8 +67,47 @@
 };
 
 &ehci {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	phys = <&exynos_usbphy 2>;
 	phy-names = "hsic0";
+
+	hub@2 {
+		compatible = "usb424,3503";
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hub@1 {
+			compatible = "usb424,9514";
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet: ethernet@1 {
+				compatible = "usb424,ec00";
+				reg = <1>;
+				/* Filled in by a bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+			};
+		};
+	};
+};
+
+&gpio_keys {
+	pinctrl-0 = <&gpio_power_key &gpio_home_key>;
+
+	home-key {
+		gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
+		linux,code = <KEY_HOME>;
+		label = "home key";
+		debounce-interval = <10>;
+		wakeup-source;
+	};
+};
+
+&hsotg {
+	dr_mode = "peripheral";
 };
 
 &mshc_0 {
@@ -81,7 +115,7 @@
 };
 
 &pinctrl_1 {
-	gpio_home_key: home_key {
+	gpio_home_key: home-key-pins {
 		samsung,pins = "gpx2-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
@@ -101,9 +135,8 @@
 		"Headphone", "Headphone Jack",
 		"Microphone", "Mic Jack",
 		"Microphone", "DMIC";
-	samsung,audio-routing =
-		"Headphone Jack", "HPL",
-		"Headphone Jack", "HPR",
-		"IN1", "Mic Jack",
-		"Mic Jack", "MICBIAS";
+	audio-routing = "Headphone Jack", "HPL",
+			"Headphone Jack", "HPR",
+			"IN1", "Mic Jack",
+			"Mic Jack", "MICBIAS";
 };
diff --git a/arch/arm/boot/dts/exynos4412-odroidx2.dts b/arch/arm/boot/dts/samsung/exynos4412-odroidx2.dts
index f4b68c75c962..7be4cbdc4413 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx2.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-odroidx2.dts
@@ -17,6 +17,6 @@
 
 	memory@40000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x7FF00000>;
+		reg = <0x40000000 0x7ff00000>;
 	};
 };
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/samsung/exynos4412-origen.dts
index ecd14b283a6b..23b151645d66 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-origen.dts
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "exynos4412.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include "exynos-mfc-reserved-memory.dtsi"
@@ -24,29 +25,27 @@
 		reg = <0x40000000 0x40000000>;
 	};
 
+	aliases {
+		mmc0 = &mshc_0;
+		mmc1 = &sdhci_2;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
 
 	firmware@203f000 {
 		compatible = "samsung,secure-firmware";
-		reg = <0x0203F000 0x1000>;
+		reg = <0x0203f000 0x1000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		mmc_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "VMEM_VDD_2.8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	mmc_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VMEM_VDD_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	display-timings {
@@ -81,12 +80,27 @@
 	cpu0-supply = <&buck2_reg>;
 };
 
+&cpu_thermal {
+	cooling-maps {
+		cooling_map0: map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+					 <&cpu2 7 7>, <&cpu3 7 7>;
+		};
+		cooling_map1: map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+					 <&cpu2 13 13>, <&cpu3 13 13>;
+		};
+	};
+};
+
 &exynos_usbphy {
 	status = "okay";
 };
 
 &ehci {
-	samsung,vbus-gpio = <&gpx3 5 1>;
+	samsung,vbus-gpio = <&gpx3 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 	phys = <&exynos_usbphy 2>, <&exynos_usbphy 3>;
 	phy-names = "hsic0", "hsic1";
@@ -107,7 +121,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	s5m8767_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s5m8767-pmic";
 		reg = <0x66>;
 
@@ -135,6 +149,14 @@
 						 <1200000>, <1200000>,
 						 <1200000>, <1200000>,
 						 <1200000>, <1200000>;
+		wakeup-source;
+
+		s5m8767_osc: clocks {
+			compatible = "samsung,s5m8767-clk";
+			#clock-cells = <1>;
+			clock-output-names = "s5m8767_ap", "s5m8767_cp",
+					     "s5m8767_bt";
+		};
 
 		regulators {
 			ldo1_reg: LDO1 {
@@ -363,63 +385,63 @@
 			};
 
 			buck1_reg: BUCK1 {
-				regulator-name = "vdd_mif";
+				regulator-name = "VDD_MIF";
 				regulator-min-microvolt = <950000>;
-				regulator-max-microvolt	= <1100000>;
+				regulator-max-microvolt = <1100000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "vdd_arm";
+				regulator-name = "VDD_ARM";
 				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt	= <1350000>;
+				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
 			};
 
 			buck3_reg: BUCK3 {
-				regulator-name = "vdd_int";
+				regulator-name = "VDD_INT";
 				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt	= <1200000>;
+				regulator-max-microvolt = <1200000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
 			};
 
 			buck4_reg: BUCK4 {
-				regulator-name = "vdd_g3d";
+				regulator-name = "VDD_G3D";
 				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt	= <1500000>;
+				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
 			};
 
 			buck5_reg: BUCK5 {
-				regulator-name = "vdd_m12";
+				regulator-name = "VDD_M12";
 				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt	= <1500000>;
+				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
 			};
 
 			buck6_reg: BUCK6 {
-				regulator-name = "vdd12_5m";
+				regulator-name = "VDD12_5M";
 				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt	= <1500000>;
+				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
 			};
 
 			buck9_reg: BUCK9 {
-				regulator-name = "vddf28_emmc";
+				regulator-name = "VDDF28_EMMC";
 				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt	= <3000000>;
+				regulator-max-microvolt = <3000000>;
 				regulator-always-on;
 				regulator-boot-on;
 				op_mode = <1>; /* Normal Mode */
@@ -437,37 +459,37 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	key_home {
+	key-home {
 		keypad,row = <0>;
 		keypad,column = <0>;
 		linux,code = <KEY_HOME>;
 	};
 
-	key_down {
+	key-down {
 		keypad,row = <0>;
 		keypad,column = <1>;
 		linux,code = <KEY_DOWN>;
 	};
 
-	key_up {
+	key-up {
 		keypad,row = <1>;
 		keypad,column = <0>;
 		linux,code = <KEY_UP>;
 	};
 
-	key_menu {
+	key-menu {
 		keypad,row = <1>;
 		keypad,column = <1>;
 		linux,code = <KEY_MENU>;
 	};
 
-	key_back {
+	key-back {
 		keypad,row = <2>;
 		keypad,column = <0>;
 		linux,code = <KEY_BACK>;
 	};
 
-	key_enter {
+	key-enter {
 		keypad,row = <2>;
 		keypad,column = <1>;
 		linux,code = <KEY_ENTER>;
@@ -481,6 +503,7 @@
 
 	broken-cd;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <2 3>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
@@ -489,14 +512,14 @@
 };
 
 &pinctrl_1 {
-	keypad_rows: keypad-rows {
+	keypad_rows: keypad-rows-pins {
 		samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	keypad_cols: keypad-cols {
+	keypad_cols: keypad-cols-pins {
 		samsung,pins = "gpx1-0", "gpx1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -506,6 +529,8 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &sdhci_2 {
diff --git a/arch/arm/boot/dts/samsung/exynos4412-p4note-n8010.dts b/arch/arm/boot/dts/samsung/exynos4412-p4note-n8010.dts
new file mode 100644
index 000000000000..0932ec5866cc
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4412-p4note-n8010.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Galaxy Note 10.1 - N801x (wifi only version)
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4412-p4note.dtsi"
+
+/ {
+	model = "Samsung Galaxy Note 10.1 (GT-N8010/N8013) based on Exynos4412";
+	compatible = "samsung,n8010", "samsung,p4note", "samsung,exynos4412", "samsung,exynos4";
+	chassis-type = "tablet";
+
+	/* this is the base variant without any kind of modem */
+};
diff --git a/arch/arm/boot/dts/samsung/exynos4412-p4note.dtsi b/arch/arm/boot/dts/samsung/exynos4412-p4note.dtsi
new file mode 100644
index 000000000000..0b89d5682f85
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4412-p4note.dtsi
@@ -0,0 +1,1229 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4412 based p4note device family base DT.
+ * Based on exynos4412-midas.dtsi.
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4412.dtsi"
+#include "exynos4412-ppmu-common.dtsi"
+
+#include <dt-bindings/clock/maxim,max77686.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/summit,smb347-charger.h>
+#include "exynos-pinctrl.h"
+
+/ {
+	compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x80000000>;
+	};
+
+	aliases {
+		mmc0 = &mshc_0;
+		mmc2 = &sdhci_2;
+		mmc3 = &sdhci_3;
+	};
+
+	chosen {
+		stdout-path = &serial_2;
+	};
+
+	firmware@204f000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x0204f000 0x1000>;
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti";
+			clock-frequency = <0>;
+		};
+
+		xusbxti {
+			compatible = "samsung,clock-xusbxti";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
+
+		key-down {
+			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		key-up {
+			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		key-power {
+			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	voltage-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_LDO1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_reg_gpio_1>;
+		gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	voltage-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_LDO2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_reg_gpio_2>;
+		gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	voltage-regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_LDO3";
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_reg_gpio_3>;
+		gpios = <&gpb 7 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <20000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	panel_vdd: voltage-regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD_ENABLE";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_enable>;
+		gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	wlan_pwrseq: sdhci3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&wifi_reset>;
+		pinctrl-names = "default";
+		clocks = <&max77686 MAX77686_CLK_PMIC>;
+		clock-names = "ext_clock";
+	};
+
+	battery_cell: battery-cell {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion";
+		constant-charge-current-max-microamp = <2200000>;
+		precharge-current-microamp = <250000>;
+		charge-term-current-microamp = <250000>;
+		constant-charge-voltage-max-microvolt = <4200000>;
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "asahi-kasei,ak8975";
+			reg = <0x0c>;
+			pinctrl-0 = <&ak8975_irq>;
+			pinctrl-names = "default";
+			interrupt-parent = <&gpm4>;
+			interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fuel-gauge@36 {
+			compatible = "maxim,max17042";
+			reg = <0x36>;
+			pinctrl-0 = <&fuel_alert_irq>;
+			pinctrl-names = "default";
+			interrupt-parent = <&gpx2>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+			maxim,rsns-microohm = <10000>;
+			maxim,over-heat-temp = <600>;
+			maxim,over-volt = <4300>;
+		};
+	};
+
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@41 {
+			compatible = "st,stmpe811";
+			reg = <0x41>;
+			pinctrl-0 = <&stmpe_adc_irq>;
+			pinctrl-names = "default";
+			interrupt-parent = <&gpx0>;
+			interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+			st,adc-freq = <3>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,sample-time = <3>;
+
+			adc {
+				compatible = "st,stmpe-adc";
+				#io-channel-cells = <1>;
+				st,norequest-mask = <0x2f>;
+			};
+		};
+	};
+
+	i2c-gpio-4 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power_supply: charger@6 {
+			compatible = "summit,smb347";
+			reg = <0x6>;
+			summit,enable-usb-charging;
+			summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
+			summit,fast-voltage-threshold-microvolt = <2600000>;
+			summit,chip-temperature-threshold-celsius = <130>;
+			summit,usb-current-limit-microamp = <1800000>;
+
+			monitored-battery = <&battery_cell>;
+		};
+	};
+
+	panel {
+		compatible = "samsung,ltl101al01";
+		pinctrl-0 = <&lvds_nshdn>;
+		pinctrl-names = "default";
+		power-supply = <&panel_vdd>;
+		enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>;
+		backlight = <&backlight>;
+
+		port {
+			lcd_ep: endpoint {
+				remote-endpoint = <&fimd_ep>;
+			};
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-0 = <&led_bl_reset>;
+		pinctrl-names = "default";
+		enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>;
+		power-supply = <&panel_vdd>;
+		pwms = <&pwm 1 78770 0>;
+		brightness-levels = <0 48 128 255>;
+		num-interpolated-steps = <8>;
+		default-brightness-level = <12>;
+	};
+};
+
+&adc {
+	vdd-supply = <&ldo3_reg>;
+	/* not verified */
+	status = "okay";
+};
+
+&bus_dmc {
+	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+	vdd-supply = <&buck1_reg>;
+	status = "okay";
+};
+
+&bus_acp {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_c2c {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_leftbus {
+	devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+	vdd-supply = <&buck3_reg>;
+	status = "okay";
+};
+
+&bus_rightbus {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_display {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_fsys {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_peri {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_mfc {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu0-supply = <&buck2_reg>;
+};
+
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+					 <&cpu2 7 7>, <&cpu3 7 7>;
+		};
+		map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+					 <&cpu2 13 13>, <&cpu3 13 13>;
+		};
+	};
+};
+
+&exynos_usbphy {
+	status = "okay";
+};
+
+&fimd {
+	pinctrl-0 = <&lcd_clk &lcd_data24>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	samsung,invert-vclk;
+
+	port@3 {
+		reg = <3>;
+
+		fimd_ep: endpoint {
+			remote-endpoint = <&lcd_ep>;
+		};
+	};
+};
+
+&gpu {
+	mali-supply = <&buck4_reg>;
+	status = "okay";
+};
+
+&hsotg {
+	vusb_a-supply = <&ldo12_reg>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&i2c_3 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <400000>;
+	pinctrl-0 = <&i2c3_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		pinctrl-0 = <&tsp_rst &tsp_irq>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpm2>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpm0 4 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c_7 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <400000>;
+	pinctrl-0 = <&i2c7_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	max77686: pmic@9 {
+		compatible = "maxim,max77686";
+		interrupt-parent = <&gpx0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&max77686_irq>;
+		pinctrl-names = "default";
+		wakeup-source;
+		reg = <0x09>;
+		#clock-cells = <1>;
+
+		voltage-regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "ldo1";
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "ldo2";
+				regulator-always-on;
+			};
+
+			/* WM8994 audio */
+			ldo3_reg: LDO3 {
+				regulator-name = "VCC_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "ldo4";
+				regulator-always-on;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "VCC_1.8V_IO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "ldo6";
+				regulator-always-on;
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "ldo7";
+				regulator-always-on;
+			};
+
+			/* CSI IP block */
+			ldo8_reg: LDO8 {
+				regulator-name = "VMIPI_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			/* IR LED on/off */
+			ldo9_reg: LDO9 {
+				regulator-name = "VLED_IC_1.9V";
+				regulator-min-microvolt = <1950000>;
+				regulator-max-microvolt = <1950000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* CSI IP block */
+			ldo10_reg: LDO10 {
+				regulator-name = "VMIPI_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "VABB1_1.9V";
+				regulator-min-microvolt = <1950000>;
+				regulator-max-microvolt = <1950000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* USB OTG */
+			ldo12_reg: LDO12 {
+				regulator-name = "VUOTG_3.0V";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			/* not connected */
+			ldo13_reg: LDO13 {
+				regulator-name = "ldo13";
+			};
+
+			ldo14_reg: LDO14 {
+				regulator-name = "VABB2_1.9V";
+				regulator-min-microvolt = <1950000>;
+				regulator-max-microvolt = <1950000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "ldo15";
+				regulator-always-on;
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "ldo16";
+				regulator-always-on;
+			};
+
+			/* not connected */
+			ldo17_reg: LDO17 {
+				regulator-name = "ldo17";
+			};
+
+			/* Camera ISX012 */
+			ldo18_reg: LDO18 {
+				regulator-name = "CAM_IO_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* Camera S5K6A3 */
+			ldo19_reg: LDO19 {
+				regulator-name = "VT_CORE_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* not connected */
+			ldo20_reg: LDO20 {
+				regulator-name = "ldo20";
+			};
+
+			/* MMC2 */
+			ldo21_reg: LDO21 {
+				regulator-name = "VTF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
+			};
+
+			/* not connected */
+			ldo22_reg: LDO22 {
+				regulator-name = "ldo22";
+			};
+
+			/* ADC */
+			ldo23_reg: LDO23 {
+				regulator-name = "VDD_ADC_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* Camera S5K6A3 */
+			ldo24_reg: LDO24 {
+				regulator-name = "CAM_A2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo25_reg: LDO25 {
+				regulator-name = "VLED_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* Camera ISX012 */
+			ldo26_reg: LDO26 {
+				regulator-name = "3MP_AF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1050000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_ARM";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_INT";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_G3D";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1075000>;
+				regulator-boot-on;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "buck5";
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "buck6";
+				regulator-always-on;
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "buck7";
+				regulator-always-on;
+			};
+
+			/* not connected */
+			buck8_reg: BUCK8 {
+				regulator-name = "buck8";
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "3MP_CORE_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&mshc_0 {
+	broken-cd;
+	non-removable;
+	card-detect-delay = <200>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <0>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	mmc-ddr-1_8v;
+	pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	status = "okay";
+};
+
+&pinctrl_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep0>;
+
+	tsp_reg_gpio_2: tsp-reg-gpio-2-pins {
+		samsung,pins = "gpb-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp_reg_gpio_3: tsp-reg-gpio-3-pins {
+		samsung,pins = "gpb-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	lcd_enable: lcd-enable-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sleep0: sleep-state {
+		PIN_SLP(gpa0-0, INPUT, NONE);
+		PIN_SLP(gpa0-1, OUT0, NONE);
+		PIN_SLP(gpa0-2, INPUT, NONE);
+		PIN_SLP(gpa0-3, INPUT, UP);
+		PIN_SLP(gpa0-4, INPUT, NONE);
+		PIN_SLP(gpa0-5, INPUT, DOWN);
+		PIN_SLP(gpa0-6, INPUT, DOWN);
+		PIN_SLP(gpa0-7, INPUT, UP);
+
+		PIN_SLP(gpa1-0, INPUT, DOWN);
+		PIN_SLP(gpa1-1, INPUT, DOWN);
+		PIN_SLP(gpa1-2, INPUT, DOWN);
+		PIN_SLP(gpa1-3, INPUT, DOWN);
+		PIN_SLP(gpa1-4, INPUT, DOWN);
+		PIN_SLP(gpa1-5, INPUT, DOWN);
+
+		PIN_SLP(gpb-0, INPUT, NONE);
+		PIN_SLP(gpb-1, INPUT, NONE);
+		PIN_SLP(gpb-2, INPUT, NONE);
+		PIN_SLP(gpb-3, INPUT, NONE);
+		PIN_SLP(gpb-4, INPUT, DOWN);
+		PIN_SLP(gpb-5, INPUT, DOWN);
+		PIN_SLP(gpb-6, INPUT, DOWN);
+		PIN_SLP(gpb-7, INPUT, DOWN);
+
+		PIN_SLP(gpc0-0, INPUT, DOWN);
+		PIN_SLP(gpc0-1, INPUT, DOWN);
+		PIN_SLP(gpc0-2, INPUT, DOWN);
+		PIN_SLP(gpc0-3, INPUT, DOWN);
+		PIN_SLP(gpc0-4, INPUT, DOWN);
+
+		PIN_SLP(gpc1-0, INPUT, UP);
+		PIN_SLP(gpc1-1, PREV, NONE);
+		PIN_SLP(gpc1-2, INPUT, UP);
+		PIN_SLP(gpc1-3, INPUT, UP);
+		PIN_SLP(gpc1-4, INPUT, UP);
+
+		PIN_SLP(gpd0-0, INPUT, DOWN);
+		PIN_SLP(gpd0-1, OUT0, NONE);
+		PIN_SLP(gpd0-2, INPUT, NONE);
+		PIN_SLP(gpd0-3, INPUT, NONE);
+
+		PIN_SLP(gpd1-0, INPUT, DOWN);
+		PIN_SLP(gpd1-1, INPUT, DOWN);
+		PIN_SLP(gpd1-2, INPUT, NONE);
+		PIN_SLP(gpd1-3, INPUT, NONE);
+
+		PIN_SLP(gpf0-0, OUT0, NONE);
+		PIN_SLP(gpf0-1, OUT0, NONE);
+		PIN_SLP(gpf0-2, OUT0, NONE);
+		PIN_SLP(gpf0-3, OUT0, NONE);
+		PIN_SLP(gpf0-4, OUT0, NONE);
+		PIN_SLP(gpf0-5, OUT0, NONE);
+		PIN_SLP(gpf0-6, OUT0, NONE);
+		PIN_SLP(gpf0-7, OUT0, NONE);
+
+		PIN_SLP(gpf1-0, OUT0, NONE);
+		PIN_SLP(gpf1-1, OUT0, NONE);
+		PIN_SLP(gpf1-2, OUT0, NONE);
+		PIN_SLP(gpf1-3, OUT0, NONE);
+		PIN_SLP(gpf1-4, OUT0, NONE);
+		PIN_SLP(gpf1-5, OUT0, NONE);
+		PIN_SLP(gpf1-6, OUT0, NONE);
+		PIN_SLP(gpf1-7, OUT0, NONE);
+
+		PIN_SLP(gpf2-0, OUT0, NONE);
+		PIN_SLP(gpf2-1, OUT0, NONE);
+		PIN_SLP(gpf2-2, OUT0, NONE);
+		PIN_SLP(gpf2-3, OUT0, NONE);
+		PIN_SLP(gpf2-4, OUT0, NONE);
+		PIN_SLP(gpf2-5, OUT0, NONE);
+		PIN_SLP(gpf2-6, OUT0, NONE);
+		PIN_SLP(gpf2-7, OUT0, NONE);
+
+		PIN_SLP(gpf3-0, OUT0, NONE);
+		PIN_SLP(gpf3-1, OUT0, NONE);
+		PIN_SLP(gpf3-2, OUT0, NONE);
+		PIN_SLP(gpf3-3, OUT0, NONE);
+		PIN_SLP(gpf3-4, OUT0, NONE);
+		PIN_SLP(gpf3-5, OUT0, NONE);
+
+		PIN_SLP(gpj0-0, INPUT, DOWN);
+		PIN_SLP(gpj0-1, INPUT, DOWN);
+		PIN_SLP(gpj0-2, INPUT, DOWN);
+		PIN_SLP(gpj0-3, PREV, NONE);
+		PIN_SLP(gpj0-4, PREV, NONE);
+		PIN_SLP(gpj0-5, OUT0, NONE);
+		PIN_SLP(gpj0-6, OUT0, NONE);
+		PIN_SLP(gpj0-7, OUT0, NONE);
+
+		PIN_SLP(gpj1-0, OUT0, NONE);
+		PIN_SLP(gpj1-1, INPUT, DOWN);
+		PIN_SLP(gpj1-2, PREV, NONE);
+		PIN_SLP(gpj1-3, OUT0, NONE);
+	};
+};
+
+&pinctrl_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep1>;
+
+	sd3_wifi: sd3-wifi-pins {
+		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_shutdown: bt-shutdown-pins {
+		samsung,pins = "gpl0-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart_sel: uart-sel-pins {
+		samsung,pins = "gpl2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-val = <1>;
+		/* 0 = CP, 1 = AP (serial output) */
+	};
+
+	led_bl_reset: led-bl-reset-pins {
+		samsung,pins = "gpm0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp_rst: tsp-rst-pins {
+		samsung,pins = "gpm0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	lvds_nshdn: lvds-nshdn-pins {
+		samsung,pins = "gpm0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp_irq: tsp-irq-pins {
+		samsung,pins = "gpm2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	wifi_reset: wifi-reset-pins {
+		samsung,pins = "gpm3-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp_reg_gpio_1: tsp-reg-gpio-1-pins {
+		samsung,pins = "gpm4-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	ak8975_irq: ak8975-irq-pins {
+		samsung,pins = "gpm4-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	stmpe_adc_irq: stmpe-adc-irq-pins {
+		samsung,pins = "gpx0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	max77686_irq: max77686-irq-pins {
+		samsung,pins = "gpx0-7";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	gpio_keys: gpio-keys-pins {
+		samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	fuel_alert_irq: fuel-alert-irq-pins {
+		samsung,pins = "gpx2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	wifi_host_wake: wifi-host-wake-pins {
+		samsung,pins = "gpx2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	bt_host_wakeup: bt-host-wakeup-pins {
+		samsung,pins = "gpx2-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_device_wakeup: bt-device-wakeup-pins {
+		samsung,pins = "gpx3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sdhci2_cd: sdhci2-cd-pins {
+		samsung,pins = "gpx3-4";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sleep1: sleep-state {
+		PIN_SLP(gpk0-0, PREV, NONE);
+		PIN_SLP(gpk0-1, PREV, NONE);
+		PIN_SLP(gpk0-2, PREV, NONE);
+		PIN_SLP(gpk0-3, PREV, NONE);
+		PIN_SLP(gpk0-4, PREV, NONE);
+		PIN_SLP(gpk0-5, PREV, NONE);
+		PIN_SLP(gpk0-6, PREV, NONE);
+
+		PIN_SLP(gpk1-0, INPUT, DOWN);
+		PIN_SLP(gpk1-1, INPUT, DOWN);
+		PIN_SLP(gpk1-2, INPUT, DOWN);
+		PIN_SLP(gpk1-3, PREV, NONE);
+		PIN_SLP(gpk1-4, PREV, NONE);
+		PIN_SLP(gpk1-5, PREV, NONE);
+		PIN_SLP(gpk1-6, PREV, NONE);
+
+		PIN_SLP(gpk2-0, INPUT, DOWN);
+		PIN_SLP(gpk2-1, INPUT, DOWN);
+		PIN_SLP(gpk2-2, INPUT, DOWN);
+		PIN_SLP(gpk2-3, INPUT, DOWN);
+		PIN_SLP(gpk2-4, INPUT, DOWN);
+		PIN_SLP(gpk2-5, INPUT, DOWN);
+		PIN_SLP(gpk2-6, INPUT, DOWN);
+
+		PIN_SLP(gpk3-0, OUT0, NONE);
+		PIN_SLP(gpk3-1, INPUT, NONE);
+		PIN_SLP(gpk3-2, INPUT, DOWN);
+		PIN_SLP(gpk3-3, INPUT, NONE);
+		PIN_SLP(gpk3-4, INPUT, NONE);
+		PIN_SLP(gpk3-5, INPUT, NONE);
+		PIN_SLP(gpk3-6, INPUT, NONE);
+
+		PIN_SLP(gpl0-0, OUT0, NONE);
+		PIN_SLP(gpl0-1, INPUT, NONE);
+		PIN_SLP(gpl0-2, INPUT, NONE);
+		PIN_SLP(gpl0-3, INPUT, DOWN);
+		PIN_SLP(gpl0-4, PREV, NONE);
+		PIN_SLP(gpl0-6, PREV, NONE);
+
+		PIN_SLP(gpl1-0, OUT0, NONE);
+		PIN_SLP(gpl1-1, OUT0, NONE);
+
+		PIN_SLP(gpl2-0, INPUT, DOWN);
+		PIN_SLP(gpl2-1, INPUT, DOWN);
+		PIN_SLP(gpl2-2, INPUT, DOWN);
+		PIN_SLP(gpl2-3, INPUT, DOWN);
+		PIN_SLP(gpl2-4, OUT0, NONE);
+		PIN_SLP(gpl2-5, INPUT, DOWN);
+		PIN_SLP(gpl2-6, PREV, NONE);
+		PIN_SLP(gpl2-7, PREV, NONE);
+
+		PIN_SLP(gpm0-0, PREV, NONE);
+		PIN_SLP(gpm0-1, OUT0, NONE);
+		PIN_SLP(gpm0-2, INPUT, DOWN);
+		PIN_SLP(gpm0-3, INPUT, NONE);
+		PIN_SLP(gpm0-4, OUT0, NONE);
+		PIN_SLP(gpm0-5, OUT0, NONE);
+		PIN_SLP(gpm0-6, INPUT, DOWN);
+		PIN_SLP(gpm0-7, OUT0, NONE);
+
+		PIN_SLP(gpm1-0, INPUT, NONE);
+		PIN_SLP(gpm1-1, INPUT, NONE);
+		PIN_SLP(gpm1-2, INPUT, NONE);
+		PIN_SLP(gpm1-3, INPUT, NONE);
+		PIN_SLP(gpm1-4, INPUT, NONE);
+		PIN_SLP(gpm1-5, INPUT, NONE);
+		PIN_SLP(gpm1-6, INPUT, DOWN);
+
+		PIN_SLP(gpm2-0, INPUT, NONE);
+		PIN_SLP(gpm2-1, INPUT, NONE);
+		PIN_SLP(gpm2-2, OUT0, NONE);
+		PIN_SLP(gpm2-3, OUT0, DOWN);
+		PIN_SLP(gpm2-4, INPUT, DOWN);
+
+		PIN_SLP(gpm3-0, PREV, NONE);
+		PIN_SLP(gpm3-1, PREV, NONE);
+		PIN_SLP(gpm3-2, PREV, NONE);
+		PIN_SLP(gpm3-3, OUT1, NONE);
+		PIN_SLP(gpm3-4, OUT0, DOWN);
+		PIN_SLP(gpm3-5, PREV, NONE);
+		PIN_SLP(gpm3-6, PREV, NONE);
+		PIN_SLP(gpm3-7, OUT0, NONE);
+
+		PIN_SLP(gpm4-0, INPUT, NONE);
+		PIN_SLP(gpm4-1, INPUT, NONE);
+		PIN_SLP(gpm4-2, INPUT, DOWN);
+		PIN_SLP(gpm4-3, INPUT, DOWN);
+		PIN_SLP(gpm4-4, PREV, NONE);
+		PIN_SLP(gpm4-5, OUT0, NONE);
+		PIN_SLP(gpm4-6, OUT0, NONE);
+		PIN_SLP(gpm4-7, INPUT, DOWN);
+
+		PIN_SLP(gpy0-0, INPUT, DOWN);
+		PIN_SLP(gpy0-1, INPUT, DOWN);
+		PIN_SLP(gpy0-2, INPUT, NONE);
+		PIN_SLP(gpy0-3, INPUT, NONE);
+		PIN_SLP(gpy0-4, INPUT, NONE);
+		PIN_SLP(gpy0-5, INPUT, NONE);
+
+		PIN_SLP(gpy1-0, INPUT, DOWN);
+		PIN_SLP(gpy1-1, INPUT, DOWN);
+		PIN_SLP(gpy1-2, INPUT, DOWN);
+		PIN_SLP(gpy1-3, INPUT, DOWN);
+
+		PIN_SLP(gpy2-0, PREV, NONE);
+		PIN_SLP(gpy2-1, INPUT, DOWN);
+		PIN_SLP(gpy2-2, INPUT, NONE);
+		PIN_SLP(gpy2-3, INPUT, NONE);
+		PIN_SLP(gpy2-4, INPUT, NONE);
+		PIN_SLP(gpy2-5, INPUT, NONE);
+
+		PIN_SLP(gpy3-0, INPUT, DOWN);
+		PIN_SLP(gpy3-1, INPUT, DOWN);
+		PIN_SLP(gpy3-2, INPUT, DOWN);
+		PIN_SLP(gpy3-3, INPUT, DOWN);
+		PIN_SLP(gpy3-4, INPUT, DOWN);
+		PIN_SLP(gpy3-5, INPUT, DOWN);
+		PIN_SLP(gpy3-6, INPUT, DOWN);
+		PIN_SLP(gpy3-7, INPUT, DOWN);
+
+		PIN_SLP(gpy4-0, INPUT, DOWN);
+		PIN_SLP(gpy4-1, INPUT, DOWN);
+		PIN_SLP(gpy4-2, INPUT, DOWN);
+		PIN_SLP(gpy4-3, INPUT, DOWN);
+		PIN_SLP(gpy4-4, INPUT, DOWN);
+		PIN_SLP(gpy4-5, INPUT, DOWN);
+		PIN_SLP(gpy4-6, INPUT, DOWN);
+		PIN_SLP(gpy4-7, INPUT, DOWN);
+
+		PIN_SLP(gpy5-0, INPUT, DOWN);
+		PIN_SLP(gpy5-1, INPUT, DOWN);
+		PIN_SLP(gpy5-2, INPUT, DOWN);
+		PIN_SLP(gpy5-3, INPUT, DOWN);
+		PIN_SLP(gpy5-4, INPUT, DOWN);
+		PIN_SLP(gpy5-5, INPUT, DOWN);
+		PIN_SLP(gpy5-6, INPUT, DOWN);
+		PIN_SLP(gpy5-7, INPUT, DOWN);
+
+		PIN_SLP(gpy6-0, INPUT, DOWN);
+		PIN_SLP(gpy6-1, INPUT, DOWN);
+		PIN_SLP(gpy6-2, INPUT, DOWN);
+		PIN_SLP(gpy6-3, INPUT, DOWN);
+		PIN_SLP(gpy6-4, INPUT, DOWN);
+		PIN_SLP(gpy6-5, INPUT, DOWN);
+		PIN_SLP(gpy6-6, INPUT, DOWN);
+		PIN_SLP(gpy6-7, INPUT, DOWN);
+	};
+};
+
+&pinctrl_2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep2>;
+
+	sleep2: sleep-state {
+		PIN_SLP(gpz-0, INPUT, DOWN);
+		PIN_SLP(gpz-1, INPUT, DOWN);
+		PIN_SLP(gpz-2, INPUT, DOWN);
+		PIN_SLP(gpz-3, INPUT, DOWN);
+		PIN_SLP(gpz-4, INPUT, DOWN);
+		PIN_SLP(gpz-5, INPUT, DOWN);
+		PIN_SLP(gpz-6, INPUT, DOWN);
+	};
+};
+
+&pinctrl_3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep3>;
+
+	sleep3: sleep-state {
+		PIN_SLP(gpv0-0, INPUT, DOWN);
+		PIN_SLP(gpv0-1, INPUT, DOWN);
+		PIN_SLP(gpv0-2, INPUT, DOWN);
+		PIN_SLP(gpv0-3, INPUT, DOWN);
+		PIN_SLP(gpv0-4, INPUT, DOWN);
+		PIN_SLP(gpv0-5, INPUT, DOWN);
+		PIN_SLP(gpv0-6, INPUT, DOWN);
+		PIN_SLP(gpv0-7, INPUT, DOWN);
+
+		PIN_SLP(gpv1-0, INPUT, DOWN);
+		PIN_SLP(gpv1-1, INPUT, DOWN);
+		PIN_SLP(gpv1-2, INPUT, DOWN);
+		PIN_SLP(gpv1-3, INPUT, DOWN);
+		PIN_SLP(gpv1-4, INPUT, DOWN);
+		PIN_SLP(gpv1-5, INPUT, DOWN);
+		PIN_SLP(gpv1-6, INPUT, DOWN);
+		PIN_SLP(gpv1-7, INPUT, DOWN);
+
+		PIN_SLP(gpv2-0, INPUT, DOWN);
+		PIN_SLP(gpv2-1, INPUT, DOWN);
+		PIN_SLP(gpv2-2, INPUT, DOWN);
+		PIN_SLP(gpv2-3, INPUT, DOWN);
+		PIN_SLP(gpv2-4, INPUT, DOWN);
+		PIN_SLP(gpv2-5, INPUT, DOWN);
+		PIN_SLP(gpv2-6, INPUT, DOWN);
+		PIN_SLP(gpv2-7, INPUT, DOWN);
+
+		PIN_SLP(gpv3-0, INPUT, DOWN);
+		PIN_SLP(gpv3-1, INPUT, DOWN);
+		PIN_SLP(gpv3-2, INPUT, DOWN);
+		PIN_SLP(gpv3-3, INPUT, DOWN);
+		PIN_SLP(gpv3-4, INPUT, DOWN);
+		PIN_SLP(gpv3-5, INPUT, DOWN);
+		PIN_SLP(gpv3-6, INPUT, DOWN);
+		PIN_SLP(gpv3-7, INPUT, DOWN);
+
+		PIN_SLP(gpv4-0, INPUT, DOWN);
+		PIN_SLP(gpv4-1, INPUT, DOWN);
+	};
+};
+
+&pmu_system_controller {
+	assigned-clocks = <&pmu_system_controller 0>;
+	assigned-clock-parents = <&clock CLK_XUSBXTI>;
+};
+
+&pwm {
+	pinctrl-0 = <&pwm1_out>;
+	pinctrl-names = "default";
+	samsung,pwm-outputs = <1>;
+	status = "okay";
+};
+
+&rtc {
+	clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+	status = "okay";
+};
+
+&sdhci_2 {
+	bus-width = <4>;
+	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
+	pinctrl-names = "default";
+	vmmc-supply = <&ldo21_reg>;
+	status = "okay";
+};
+
+&sdhci_3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>;
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_host_wake>;
+		interrupt-parent = <&gpx2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&serial_0 {
+	pinctrl-0 = <&uart0_data &uart0_fctl>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
+		pinctrl-names = "default";
+
+		max-speed = <2000000>;
+		shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&max77686 MAX77686_CLK_PMIC>;
+		clock-names = "lpo";
+	};
+};
+
+&serial_2 {
+	pinctrl-0 = <&uart_sel>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&tmu {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/samsung/exynos4412-ppmu-common.dtsi b/arch/arm/boot/dts/samsung/exynos4412-ppmu-common.dtsi
new file mode 100644
index 000000000000..7f187a3dedcc
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4412-ppmu-common.dtsi
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree sources for Exynos4412 PPMU common device tree
+ *
+ * Copyright (C) 2015 Samsung Electronics
+ * Author: Chanwoo Choi <cw00.choi@samsung.com>
+ */
+
+&ppmu_dmc0 {
+	status = "okay";
+
+	events {
+		ppmu_dmc0_3: ppmu-event3-dmc0 {
+			event-name = "ppmu-event3-dmc0";
+		};
+	};
+};
+
+&ppmu_dmc1 {
+	status = "okay";
+
+	events {
+		ppmu_dmc1_3: ppmu-event3-dmc1 {
+			event-name = "ppmu-event3-dmc1";
+		};
+	};
+};
+
+&ppmu_leftbus {
+	status = "okay";
+
+	events {
+		ppmu_leftbus_3: ppmu-event3-leftbus {
+			event-name = "ppmu-event3-leftbus";
+		};
+	};
+};
+
+&ppmu_rightbus {
+	status = "okay";
+
+	events {
+		ppmu_rightbus_3: ppmu-event3-rightbus {
+			event-name = "ppmu-event3-rightbus";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos4412-prime.dtsi b/arch/arm/boot/dts/samsung/exynos4412-prime.dtsi
index 3731a225f779..3731a225f779 100644
--- a/arch/arm/boot/dts/exynos4412-prime.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4412-prime.dtsi
diff --git a/arch/arm/boot/dts/exynos4412-smdk4412.dts b/arch/arm/boot/dts/samsung/exynos4412-smdk4412.dts
index e70fb6e601f0..715dfcba1417 100644
--- a/arch/arm/boot/dts/exynos4412-smdk4412.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-smdk4412.dts
@@ -22,6 +22,10 @@
 		reg = <0x40000000 0x40000000>;
 	};
 
+	aliases {
+		mmc0 = &sdhci_2;
+	};
+
 	chosen {
 		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M init=/linuxrc";
 		stdout-path = "serial1:115200n8";
@@ -37,6 +41,28 @@
 			compatible = "samsung,clock-xusbxti";
 			clock-frequency = <24000000>;
 		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&cpu_thermal {
+	cooling-maps {
+		cooling_map0: map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+					 <&cpu2 7 7>, <&cpu3 7 7>;
+		};
+		cooling_map1: map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+					 <&cpu2 13 13>, <&cpu3 13 13>;
+		};
 	};
 };
 
@@ -49,61 +75,61 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	key_1 {
+	key-1 {
 		keypad,row = <1>;
 		keypad,column = <3>;
 		linux,code = <2>;
 	};
 
-	key_2 {
+	key-2 {
 		keypad,row = <1>;
 		keypad,column = <4>;
 		linux,code = <3>;
 	};
 
-	key_3 {
+	key-3 {
 		keypad,row = <1>;
 		keypad,column = <5>;
 		linux,code = <4>;
 	};
 
-	key_4 {
+	key-4 {
 		keypad,row = <1>;
 		keypad,column = <6>;
 		linux,code = <5>;
 	};
 
-	key_5 {
+	key-5 {
 		keypad,row = <1>;
 		keypad,column = <7>;
 		linux,code = <6>;
 	};
 
-	key_A {
+	key-A {
 		keypad,row = <2>;
 		keypad,column = <6>;
 		linux,code = <30>;
 	};
 
-	key_B {
+	key-B {
 		keypad,row = <2>;
 		keypad,column = <7>;
 		linux,code = <48>;
 	};
 
-	key_C {
+	key-C {
 		keypad,row = <0>;
 		keypad,column = <5>;
 		linux,code = <46>;
 	};
 
-	key_D {
+	key-D {
 		keypad,row = <2>;
 		keypad,column = <5>;
 		linux,code = <32>;
 	};
 
-	key_E {
+	key-E {
 		keypad,row = <0>;
 		keypad,column = <7>;
 		linux,code = <18>;
@@ -111,14 +137,14 @@
 };
 
 &pinctrl_1 {
-	keypad_rows: keypad-rows {
+	keypad_rows: keypad-rows-pins {
 		samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	keypad_cols: keypad-cols {
+	keypad_cols: keypad-cols-pins {
 		samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
 			       "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -127,6 +153,11 @@
 	};
 };
 
+&rtc {
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sdhci_2 {
 	bus-width = <4>;
 	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
diff --git a/arch/arm/boot/dts/exynos4412-tiny4412.dts b/arch/arm/boot/dts/samsung/exynos4412-tiny4412.dts
index 01f37b5ac9c4..5a2dcdc5c28b 100644
--- a/arch/arm/boot/dts/exynos4412-tiny4412.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-tiny4412.dts
@@ -11,11 +11,16 @@
 /dts-v1/;
 #include "exynos4412.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "FriendlyARM TINY4412 board based on Exynos4412";
 	compatible = "friendlyarm,tiny4412", "samsung,exynos4412", "samsung,exynos4";
 
+	aliases {
+		mmc0 = &sdhci_2;
+	};
+
 	chosen {
 		stdout-path = &serial_0;
 	};
@@ -30,6 +35,7 @@
 
 		led1 {
 			label = "led1";
+			function = LED_FUNCTION_HEARTBEAT;
 			gpios = <&gpm4 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
@@ -49,6 +55,7 @@
 
 		led4 {
 			label = "led4";
+			function = LED_FUNCTION_DISK_ACTIVITY;
 			gpios = <&gpm4 3 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "mmc0";
@@ -65,11 +72,68 @@
 			compatible = "samsung,clock-xusbxti";
 			clock-frequency = <24000000>;
 		};
+
+		pmic_ap_clk: pmic-ap-clk {
+			/* Workaround for missing clock on PMIC */
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	panel {
+		compatible = "innolux,at070tn92";
+		power-supply = <&vddq_lcd>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&lcdc_output>;
+			};
+		};
+	};
+
+	vddq_lcd: regulator-vddq-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "vddq-lcd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+};
+
+&cpu_thermal {
+	cooling-maps {
+		cooling_map0: map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
+					 <&cpu2 7 7>, <&cpu3 7 7>;
+		};
+		cooling_map1: map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
+					 <&cpu2 13 13>, <&cpu3 13 13>;
+		};
+	};
+};
+
+&fimd {
+	pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	port@3 {
+		reg = <3>;
+		lcdc_output: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
 	};
 };
 
 &rtc {
 	status = "okay";
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &sdhci_2 {
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/samsung/exynos4412-trats2.dts
index aac533933c61..3c2d2a7836da 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/samsung/exynos4412-trats2.dts
@@ -15,10 +15,11 @@
 / {
 	model = "Samsung Trats 2 based on Exynos4412";
 	compatible = "samsung,trats2", "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
+	chassis-type = "handset";
 
 	memory@40000000 {
 		device_type = "memory";
-		reg =  <0x40000000 0x40000000>;
+		reg = <0x40000000 0x40000000>;
 	};
 
 	chosen {
diff --git a/arch/arm/boot/dts/samsung/exynos4412.dtsi b/arch/arm/boot/dts/samsung/exynos4412.dtsi
new file mode 100644
index 000000000000..dcbe0ce6180f
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos4412.dtsi
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4412 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4412 SoC device nodes are listed in this file. Exynos4412
+ * based board files can include this file and provide values for board specific
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4412 SoC. As device tree coverage for Exynos4412 increases, additional
+ * nodes can be added to this file.
+ */
+
+#include "exynos4x12.dtsi"
+
+/ {
+	compatible = "samsung,exynos4412", "samsung,exynos4";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@a00 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0xa00>;
+			clocks = <&clock CLK_ARM_CLK>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+
+		cpu1: cpu@a01 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0xa01>;
+			clocks = <&clock CLK_ARM_CLK>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+
+		cpu2: cpu@a02 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0xa02>;
+			clocks = <&clock CLK_ARM_CLK>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+
+		cpu3: cpu@a03 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0xa03>;
+			clocks = <&clock CLK_ARM_CLK>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+	};
+
+	cpu0_opp_table: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <900000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <900000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <925000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <950000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <975000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-700000000 {
+			opp-hz = /bits/ 64 <700000000>;
+			opp-microvolt = <987500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <200000>;
+			opp-suspend;
+		};
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-microvolt = <1037500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1087500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1100000000 {
+			opp-hz = /bits/ 64 <1100000000>;
+			opp-microvolt = <1137500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1187500>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1300000000 {
+			opp-hz = /bits/ 64 <1300000000>;
+			opp-microvolt = <1250000>;
+			clock-latency-ns = <200000>;
+		};
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-microvolt = <1287500>;
+			clock-latency-ns = <200000>;
+		};
+		cpu0_opp_1500: opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <1350000>;
+			clock-latency-ns = <200000>;
+			turbo-mode;
+		};
+	};
+};
+
+&clock {
+	compatible = "samsung,exynos4412-clock";
+};
+
+&combiner {
+	samsung,combiner-nr = <20>;
+};
+
+&gic {
+	cpu-offset = <0x4000>;
+};
+
+&pmu {
+	interrupts = <2 2>, <3 2>, <18 2>, <19 2>;
+	interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	status = "okay";
+};
+
+&pmu_system_controller {
+	compatible = "samsung,exynos4412-pmu", "simple-mfd", "syscon";
+};
diff --git a/arch/arm/boot/dts/exynos4412-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos4x12-pinctrl.dtsi
index d7d5fdc230d8..04935fbe2f2a 100644
--- a/arch/arm/boot/dts/exynos4412-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4x12-pinctrl.dtsi
@@ -1,25 +1,25 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Samsung's Exynos4412 SoCs pin-mux and pin-config device tree source
+ * Samsung's Exynos4x12 SoCs pin-mux and pin-config device tree source
  *
  * Copyright (c) 2012 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * Samsung's Exynos4412 SoCs pin-mux and pin-config optiosn are listed as device
- * tree nodes are listed in this file.
+ * Samsung's Exynos4x12 SoCs pin-mux and pin-config options are listed as device
+ * tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 #define PIN_SLP(_pin, _mode, _pull)					\
-	_pin {								\
+	pin- ## _pin {							\
 		samsung,pins = #_pin;					\
 		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_ ##_mode>;	\
 		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_ ##_pull>;	\
 	}
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -27,7 +27,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -35,7 +35,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -43,7 +43,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -51,7 +51,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -59,7 +59,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -67,7 +67,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -75,7 +75,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -83,7 +83,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -91,7 +91,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -99,7 +99,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -107,7 +107,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -115,7 +115,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -123,112 +123,112 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_a: uart-audio-a {
+	uart_audio_a: uart-audio-a-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_b: uart-audio-b {
+	uart_audio_b: uart-audio-b-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -236,7 +236,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -244,7 +244,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
@@ -252,7 +252,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -260,7 +260,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -268,105 +268,105 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpc1-1", "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	mipi0_clk: mipi0-clk {
+	mipi0_clk: mipi0-clk-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	mipi1_clk: mipi1-clk {
+	mipi1_clk: mipi1-clk-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_clk: lcd-clk {
+	lcd_clk: lcd-clk-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpf0-7", "gpf1-0", "gpf1-1", "gpf1-2",
 				"gpf1-3", "gpf1-6", "gpf1-7", "gpf2-0",
 				"gpf2-1", "gpf2-2", "gpf2-3", "gpf2-7",
@@ -376,7 +376,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpf0-6", "gpf0-7", "gpf1-0", "gpf1-1",
 				"gpf1-2", "gpf1-3", "gpf1-6", "gpf1-7",
 				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
@@ -387,7 +387,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
 				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
 				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
@@ -399,14 +399,14 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_ldi: lcd-ldi {
+	lcd_ldi: lcd-ldi-pins {
 		samsung,pins = "gpf3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_io: cam-port-a-io {
+	cam_port_a_io: cam-port-a-io-pins {
 		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
 				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
 				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
@@ -415,14 +415,14 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_clk_active: cam-port-a-clk-active {
+	cam_port_a_clk_active: cam-port-a-clk-active-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_a_clk_idle: cam-port-a-clk-idle {
+	cam_port_a_clk_idle: cam-port-a-clk-idle-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -431,7 +431,7 @@
 };
 
 &pinctrl_1 {
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -439,7 +439,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -447,7 +447,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -455,7 +455,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk3: gpk3 {
+	gpk3: gpk3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -463,7 +463,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl0: gpl0 {
+	gpl0: gpl0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -471,7 +471,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl1: gpl1 {
+	gpl1: gpl1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -479,7 +479,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl2: gpl2 {
+	gpl2: gpl2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -487,7 +487,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm0: gpm0 {
+	gpm0: gpm0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -495,7 +495,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm1: gpm1 {
+	gpm1: gpm1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -503,7 +503,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm2: gpm2 {
+	gpm2: gpm2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -511,7 +511,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm3: gpm3 {
+	gpm3: gpm3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -519,7 +519,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm4: gpm4 {
+	gpm4: gpm4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -527,42 +527,42 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -579,7 +579,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -596,7 +596,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -604,7 +604,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -612,203 +612,203 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_clk: sd4-clk {
+	sd4_clk: sd4-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cmd: sd4-cmd {
+	sd4_cmd: sd4-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cd: sd4-cd {
+	sd4_cd: sd4-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus1: sd4-bus-width1 {
+	sd4_bus1: sd4-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus4: sd4-bus-width4 {
+	sd4_bus4: sd4-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus8: sd4-bus-width8 {
+	sd4_bus8: sd4-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpk1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpk1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpk1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpk2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpk2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpk2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpk2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpk3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpk3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpk3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpk3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_io: cam-port-b-io {
+	cam_port_b_io: cam-port-b-io-pins {
 		samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
 				"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
 				"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
@@ -817,77 +817,77 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_b_clk_active: cam-port-b-clk-active {
+	cam_port_b_clk_active: cam-port-b-clk-active-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_clk_idle: cam-port-b-clk-idle {
+	cam_port_b_clk_idle: cam-port-b-clk-idle-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint0: ext-int0 {
+	eint0: ext-int0-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint8: ext-int8 {
+	eint8: ext-int8-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint15: ext-int15 {
+	eint15: ext-int15-pins {
 		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint16: ext-int16 {
+	eint16: ext-int16-pins {
 		samsung,pins = "gpx2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint31: ext-int31 {
+	eint31: ext-int31-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c0: fimc-is-i2c0 {
+	fimc_is_i2c0: fimc-is-i2c0-pins {
 		samsung,pins = "gpm4-0", "gpm4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c1: fimc-is-i2c1 {
+	fimc_is_i2c1: fimc-is-i2c1-pins {
 		samsung,pins = "gpm4-2", "gpm4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_uart: fimc-is-uart {
+	fimc_is_uart: fimc-is-uart-pins {
 		samsung,pins = "gpm3-5", "gpm3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -896,7 +896,7 @@
 };
 
 &pinctrl_2 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -904,7 +904,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -912,7 +912,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -922,7 +922,7 @@
 };
 
 &pinctrl_3 {
-	gpv0: gpv0 {
+	gpv0: gpv0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -930,7 +930,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv1: gpv1 {
+	gpv1: gpv1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -938,7 +938,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv2: gpv2 {
+	gpv2: gpv2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -946,7 +946,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv3: gpv3 {
+	gpv3: gpv3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -954,7 +954,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv4: gpv4 {
+	gpv4: gpv4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -962,7 +962,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	c2c_bus: c2c-bus {
+	c2c_bus: c2c-bus-pins {
 		samsung,pins = "gpv0-0", "gpv0-1", "gpv0-2", "gpv0-3",
 				"gpv0-4", "gpv0-5", "gpv0-6", "gpv0-7",
 				"gpv1-0", "gpv1-1", "gpv1-2", "gpv1-3",
diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/samsung/exynos4x12.dtsi
index 5022aa574b26..b4b5e769145b 100644
--- a/arch/arm/boot/dts/exynos4412.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos4x12.dtsi
@@ -5,12 +5,12 @@
  * Copyright (c) 2012 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * Samsung's Exynos4412 SoC device nodes are listed in this file. Exynos4412
- * based board files can include this file and provide values for board specfic
- * bindings.
+ * Samsung's Exynos4x12 SoC series device nodes are listed in this file.
+ * Particular SoCs from Exynos4x12 series can include this file and provide
+ * values for SoCs specific bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
- * Exynos4412 SoC. As device tree coverage for Exynos4412 increases, additional
+ * Exynos4x12 SoCs. As device tree coverage for Exynos4x12 increases, additional
  * nodes can be added to this file.
  */
 
@@ -19,8 +19,6 @@
 #include "exynos4-cpu-thermal.dtsi"
 
 / {
-	compatible = "samsung,exynos4412", "samsung,exynos4";
-
 	aliases {
 		pinctrl0 = &pinctrl_0;
 		pinctrl1 = &pinctrl_1;
@@ -28,133 +26,184 @@
 		pinctrl3 = &pinctrl_3;
 		fimc-lite0 = &fimc_lite_0;
 		fimc-lite1 = &fimc_lite_1;
-		mshc0 = &mshc_0;
 	};
 
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@a00 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0xA00>;
-			clocks = <&clock CLK_ARM_CLK>;
-			clock-names = "cpu";
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>; /* min followed by max */
-		};
-
-		cpu1: cpu@a01 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0xA01>;
-			clocks = <&clock CLK_ARM_CLK>;
-			clock-names = "cpu";
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>; /* min followed by max */
-		};
-
-		cpu2: cpu@a02 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0xA02>;
-			clocks = <&clock CLK_ARM_CLK>;
-			clock-names = "cpu";
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>; /* min followed by max */
-		};
-
-		cpu3: cpu@a03 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0xA03>;
-			clocks = <&clock CLK_ARM_CLK>;
-			clock-names = "cpu";
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>; /* min followed by max */
+	bus_acp: bus-acp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_ACP>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_acp_opp_table>;
+		status = "disabled";
+
+		bus_acp_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+			};
+			opp-160000000 {
+				opp-hz = /bits/ 64 <160000000>;
+			};
+			opp-267000000 {
+				opp-hz = /bits/ 64 <267000000>;
+			};
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	bus_c2c: bus-c2c {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_C2C>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_dmc: bus-dmc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_DMC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		samsung,data-clock-ratio = <4>;
+		#interconnect-cells = <0>;
+		status = "disabled";
+	};
+
+	bus_display: bus-display {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK160>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_display_opp_table>;
+		interconnects = <&bus_leftbus &bus_dmc>;
+		#interconnect-cells = <0>;
+		status = "disabled";
+
+		bus_display_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-160000000 {
+				opp-hz = /bits/ 64 <160000000>;
+			};
+			opp-200000000 {
+				opp-hz = /bits/ 64 <200000000>;
+			};
+		};
+	};
+
+	bus_fsys: bus-fsys {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK133>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_fsys_opp_table>;
+		status = "disabled";
+
+		bus_fsys_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+			opp-134000000 {
+				opp-hz = /bits/ 64 <134000000>;
+			};
+		};
+	};
+
+	bus_leftbus: bus-leftbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_GDL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		interconnects = <&bus_dmc>;
+		#interconnect-cells = <0>;
+		status = "disabled";
+	};
+
+	bus_mfc: bus-mfc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_SCLK_MFC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_peri: bus-peri {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK100>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_peri_opp_table>;
+		status = "disabled";
+
+		bus_peri_opp_table: opp-table {
+			compatible = "operating-points-v2";
+
+			opp-50000000 {
+				opp-hz = /bits/ 64 <50000000>;
+			};
+			opp-100000000 {
+				opp-hz = /bits/ 64 <100000000>;
+			};
+		};
+	};
+
+	bus_rightbus: bus-rightbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_GDR>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_dmc_opp_table: opp-table-1 {
 		compatible = "operating-points-v2";
-		opp-shared;
 
-		opp-200000000 {
-			opp-hz = /bits/ 64 <200000000>;
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <900000>;
+		};
+		opp-134000000 {
+			opp-hz = /bits/ 64 <134000000>;
 			opp-microvolt = <900000>;
-			clock-latency-ns = <200000>;
 		};
-		opp-300000000 {
-			opp-hz = /bits/ 64 <300000000>;
+		opp-160000000 {
+			opp-hz = /bits/ 64 <160000000>;
 			opp-microvolt = <900000>;
-			clock-latency-ns = <200000>;
+		};
+		opp-267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+			opp-microvolt = <950000>;
 		};
 		opp-400000000 {
 			opp-hz = /bits/ 64 <400000000>;
-			opp-microvolt = <925000>;
-			clock-latency-ns = <200000>;
+			opp-microvolt = <1050000>;
+			opp-suspend;
 		};
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <950000>;
-			clock-latency-ns = <200000>;
+	};
+
+	bus_leftbus_opp_table: opp-table-2 {
+		compatible = "operating-points-v2";
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <900000>;
 		};
-		opp-600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <975000>;
-			clock-latency-ns = <200000>;
+		opp-134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+			opp-microvolt = <925000>;
 		};
-		opp-700000000 {
-			opp-hz = /bits/ 64 <700000000>;
-			opp-microvolt = <987500>;
-			clock-latency-ns = <200000>;
+		opp-160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <950000>;
 		};
-		opp-800000000 {
-			opp-hz = /bits/ 64 <800000000>;
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
 			opp-microvolt = <1000000>;
-			clock-latency-ns = <200000>;
 			opp-suspend;
 		};
-		opp-900000000 {
-			opp-hz = /bits/ 64 <900000000>;
-			opp-microvolt = <1037500>;
-			clock-latency-ns = <200000>;
-		};
-		opp-1000000000 {
-			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <1087500>;
-			clock-latency-ns = <200000>;
-		};
-		opp-1100000000 {
-			opp-hz = /bits/ 64 <1100000000>;
-			opp-microvolt = <1137500>;
-			clock-latency-ns = <200000>;
-		};
-		opp-1200000000 {
-			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <1187500>;
-			clock-latency-ns = <200000>;
-		};
-		opp-1300000000 {
-			opp-hz = /bits/ 64 <1300000000>;
-			opp-microvolt = <1250000>;
-			clock-latency-ns = <200000>;
-		};
-		opp-1400000000 {
-			opp-hz = /bits/ 64 <1400000000>;
-			opp-microvolt = <1287500>;
-			clock-latency-ns = <200000>;
-		};
-		cpu0_opp_1500: opp-1500000000 {
-			opp-hz = /bits/ 64 <1500000000>;
-			opp-microvolt = <1350000>;
-			clock-latency-ns = <200000>;
-			turbo-mode;
-		};
 	};
 
-
 	soc: soc {
 
 		pinctrl_0: pinctrl@11400000 {
@@ -184,7 +233,7 @@
 
 		pinctrl_3: pinctrl@106e0000 {
 			compatible = "samsung,exynos4x12-pinctrl";
-			reg = <0x106E0000 0x1000>;
+			reg = <0x106e0000 0x1000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
@@ -195,12 +244,12 @@
 			#size-cells = <1>;
 			ranges = <0 0x02020000 0x40000>;
 
-			smp-sysram@0 {
+			smp-sram@0 {
 				compatible = "samsung,exynos4210-sysram";
 				reg = <0x0 0x1000>;
 			};
 
-			smp-sysram@2f000 {
+			smp-sram@2f000 {
 				compatible = "samsung,exynos4210-sysram-ns";
 				reg = <0x2f000 0x1000>;
 			};
@@ -208,16 +257,18 @@
 
 		pd_isp: power-domain@10023ca0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x10023CA0 0x20>;
+			reg = <0x10023ca0 0x20>;
 			#power-domain-cells = <0>;
 			label = "ISP";
 		};
 
-		l2c: l2-cache-controller@10502000 {
+		l2c: cache-controller@10502000 {
 			compatible = "arm,pl310-cache";
 			reg = <0x10502000 0x1000>;
 			cache-unified;
 			cache-level = <2>;
+			prefetch-data = <1>;
+			prefetch-instr = <1>;
 			arm,tag-latency = <2 2 1>;
 			arm,data-latency = <3 2 1>;
 			arm,double-linefill = <1>;
@@ -228,7 +279,6 @@
 		};
 
 		clock: clock-controller@10030000 {
-			compatible = "samsung,exynos4412-clock";
 			reg = <0x10030000 0x18000>;
 			#clock-cells = <1>;
 		};
@@ -266,13 +316,12 @@
 
 		adc: adc@126c0000 {
 			compatible = "samsung,exynos4212-adc";
-			reg = <0x126C0000 0x100>;
+			reg = <0x126c0000 0x100>;
 			interrupt-parent = <&combiner>;
 			interrupts = <10 3>;
 			clocks = <&clock CLK_TSADC>;
 			clock-names = "adc";
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 			samsung,syscon-phandle = <&pmu_system_controller>;
 			status = "disabled";
 		};
@@ -300,7 +349,7 @@
 
 		sysmmu_g2d: sysmmu@10a40000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x10A40000 0x1000>;
+			reg = <0x10a40000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 7>;
 			clock-names = "sysmmu", "master";
@@ -332,7 +381,7 @@
 
 		sysmmu_fimc_fd: sysmmu@122a0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x122A0000 0x1000>;
+			reg = <0x122a0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <16 4>;
 			power-domains = <&pd_isp>;
@@ -343,7 +392,7 @@
 
 		sysmmu_fimc_mcuctl: sysmmu@122b0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x122B0000 0x1000>;
+			reg = <0x122b0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <16 5>;
 			power-domains = <&pd_isp>;
@@ -354,7 +403,7 @@
 
 		sysmmu_fimc_lite0: sysmmu@123b0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x123B0000 0x1000>;
+			reg = <0x123b0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <16 0>;
 			power-domains = <&pd_isp>;
@@ -366,7 +415,7 @@
 
 		sysmmu_fimc_lite1: sysmmu@123c0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x123C0000 0x1000>;
+			reg = <0x123c0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <16 1>;
 			power-domains = <&pd_isp>;
@@ -375,187 +424,10 @@
 				 <&isp_clock CLK_ISP_FIMC_LITE1>;
 			#iommu-cells = <0>;
 		};
-
-		bus_dmc: bus_dmc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_DMC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_dmc_opp_table>;
-			status = "disabled";
-		};
-
-		bus_acp: bus_acp {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_ACP>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_acp_opp_table>;
-			status = "disabled";
-		};
-
-		bus_c2c: bus_c2c {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_C2C>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_dmc_opp_table>;
-			status = "disabled";
-		};
-
-		bus_dmc_opp_table: opp_table1 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-				opp-microvolt = <900000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-				opp-microvolt = <900000>;
-			};
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-				opp-microvolt = <900000>;
-			};
-			opp-267000000 {
-				opp-hz = /bits/ 64 <267000000>;
-				opp-microvolt = <950000>;
-			};
-			opp-400000000 {
-				opp-hz = /bits/ 64 <400000000>;
-				opp-microvolt = <1050000>;
-				opp-suspend;
-			};
-		};
-
-		bus_acp_opp_table: opp_table2 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-			};
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-			};
-			opp-267000000 {
-				opp-hz = /bits/ 64 <267000000>;
-			};
-		};
-
-		bus_leftbus: bus_leftbus {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_GDL>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_rightbus: bus_rightbus {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DIV_GDR>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_display: bus_display {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK160>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_display_opp_table>;
-			status = "disabled";
-		};
-
-		bus_fsys: bus_fsys {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK133>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_fsys_opp_table>;
-			status = "disabled";
-		};
-
-		bus_peri: bus_peri {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_ACLK100>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_peri_opp_table>;
-			status = "disabled";
-		};
-
-		bus_mfc: bus_mfc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_SCLK_MFC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_leftbus_opp_table>;
-			status = "disabled";
-		};
-
-		bus_leftbus_opp_table: opp_table3 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-				opp-microvolt = <900000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-				opp-microvolt = <925000>;
-			};
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-				opp-microvolt = <950000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-				opp-microvolt = <1000000>;
-				opp-suspend;
-			};
-		};
-
-		bus_display_opp_table: opp_table4 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-160000000 {
-				opp-hz = /bits/ 64 <160000000>;
-			};
-			opp-200000000 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-		};
-
-		bus_fsys_opp_table: opp_table5 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp-134000000 {
-				opp-hz = /bits/ 64 <134000000>;
-			};
-		};
-
-		bus_peri_opp_table: opp_table6 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-			};
-			opp-100000000 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-		};
 	};
 };
 
 &combiner {
-	samsung,combiner-nr = <20>;
 	interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
@@ -579,14 +451,15 @@
 };
 
 &camera {
+	ranges = <0x0 0x11800000 0xba1000>;
 	clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>,
 		 <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
 	clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
 
 	/* fimc_[0-3] are configured outside, under phandles */
-	fimc_lite_0: fimc-lite@12390000 {
+	fimc_lite_0: fimc-lite@b90000 {
 		compatible = "samsung,exynos4212-fimc-lite";
-		reg = <0x12390000 0x1000>;
+		reg = <0x00b90000 0x1000>;
 		interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 		power-domains = <&pd_isp>;
 		clocks = <&isp_clock CLK_ISP_FIMC_LITE0>;
@@ -595,9 +468,9 @@
 		status = "disabled";
 	};
 
-	fimc_lite_1: fimc-lite@123a0000 {
+	fimc_lite_1: fimc-lite@ba0000 {
 		compatible = "samsung,exynos4212-fimc-lite";
-		reg = <0x123A0000 0x1000>;
+		reg = <0x00ba0000 0x1000>;
 		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 		power-domains = <&pd_isp>;
 		clocks = <&isp_clock CLK_ISP_FIMC_LITE1>;
@@ -606,9 +479,9 @@
 		status = "disabled";
 	};
 
-	fimc_is: fimc-is@12000000 {
+	fimc_is: fimc-is@800000 {
 		compatible = "samsung,exynos4212-fimc-is";
-		reg = <0x12000000 0x260000>;
+		reg = <0x00800000 0x260000>;
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 		power-domains = <&pd_isp>;
@@ -644,18 +517,15 @@
 		iommus = <&sysmmu_fimc_isp>, <&sysmmu_fimc_drc>,
 			 <&sysmmu_fimc_fd>, <&sysmmu_fimc_mcuctl>;
 		iommu-names = "isp", "drc", "fd", "mcuctl";
+		samsung,pmu-syscon = <&pmu_system_controller>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 		status = "disabled";
 
-		pmu@10020000 {
-			reg = <0x10020000 0x3000>;
-		};
-
-		i2c1_isp: i2c-isp@12140000 {
+		i2c1_isp: i2c-isp@940000 {
 			compatible = "samsung,exynos4212-i2c-isp";
-			reg = <0x12140000 0x100>;
+			reg = <0x00940000 0x100>;
 			clocks = <&isp_clock CLK_ISP_I2C1_ISP>;
 			clock-names = "i2c_isp";
 			#address-cells = <1>;
@@ -703,10 +573,6 @@
 	samsung,lcd-wb;
 };
 
-&gic {
-	cpu-offset = <0x4000>;
-};
-
 &gpu {
 	interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
@@ -732,7 +598,7 @@
 			  "pmu";
 	operating-points-v2 = <&gpu_opp_table>;
 
-	gpu_opp_table: opp_table {
+	gpu_opp_table: opp-table {
 		compatible = "operating-points-v2";
 
 		opp-160000000 {
@@ -771,16 +637,10 @@
 	clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
 	clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
 		 <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
-};
-
-&pmu {
-	interrupts = <2 2>, <3 2>, <18 2>, <19 2>;
-	interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
-	status = "okay";
+	interconnects = <&bus_display &bus_dmc>;
 };
 
 &pmu_system_controller {
-	compatible = "samsung,exynos4412-pmu", "syscon";
 	clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
 			"clkout4", "clkout8", "clkout9";
 	clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
@@ -793,10 +653,10 @@
 	compatible = "samsung,exynos4412-tmu";
 	interrupt-parent = <&combiner>;
 	interrupts = <2 4>;
-	reg = <0x100C0000 0x100>;
-	clocks = <&clock 383>;
+	reg = <0x100c0000 0x100>;
+	clocks = <&clock CLK_TMU_APBIF>;
 	clock-names = "tmu_apbif";
 	status = "disabled";
 };
 
-#include "exynos4412-pinctrl.dtsi"
+#include "exynos4x12-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/samsung/exynos5.dtsi
index 4801ca759feb..4a17a19586bb 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5.dtsi
@@ -7,7 +7,7 @@
  *
  * Samsung's Exynos5 SoC series device nodes are listed in this file. Particular
  * SoCs from Exynos5 series can include this file and provide values for SoCs
- * specfic bindings.
+ * specific bindings.
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -36,7 +36,7 @@
 		ranges;
 
 		chipid: chipid@10000000 {
-			compatible = "samsung,exynos4210-chipid", "syscon";
+			compatible = "samsung,exynos4210-chipid";
 			reg = <0x10000000 0x100>;
 		};
 
@@ -86,10 +86,10 @@
 		};
 
 		gic: interrupt-controller@10481000 {
-			compatible = "arm,gic-400", "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+			compatible = "arm,gic-400", "arm,cortex-a15-gic";
 			#interrupt-cells = <3>;
 			interrupt-controller;
-			reg =	<0x10481000 0x1000>,
+			reg = <0x10481000 0x1000>,
 				<0x10482000 0x2000>,
 				<0x10484000 0x2000>,
 				<0x10486000 0x2000>;
@@ -104,31 +104,31 @@
 
 		serial_0: serial@12c00000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C00000 0x100>;
+			reg = <0x12c00000 0x100>;
 			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		serial_1: serial@12c10000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C10000 0x100>;
+			reg = <0x12c10000 0x100>;
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		serial_2: serial@12c20000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C20000 0x100>;
+			reg = <0x12c20000 0x100>;
 			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		serial_3: serial@12c30000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C30000 0x100>;
+			reg = <0x12c30000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		i2c_0: i2c@12c60000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12C60000 0x100>;
+			reg = <0x12c60000 0x100>;
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -138,7 +138,7 @@
 
 		i2c_1: i2c@12c70000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12C70000 0x100>;
+			reg = <0x12c70000 0x100>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -148,7 +148,7 @@
 
 		i2c_2: i2c@12c80000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12C80000 0x100>;
+			reg = <0x12c80000 0x100>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -158,7 +158,7 @@
 
 		i2c_3: i2c@12c90000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12C90000 0x100>;
+			reg = <0x12c90000 0x100>;
 			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -168,7 +168,7 @@
 
 		pwm: pwm@12dd0000 {
 			compatible = "samsung,exynos4210-pwm";
-			reg = <0x12DD0000 0x100>;
+			reg = <0x12dd0000 0x100>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
@@ -180,7 +180,7 @@
 
 		rtc: rtc@101e0000 {
 			compatible = "samsung,s3c6410-rtc";
-			reg = <0x101E0000 0x100>;
+			reg = <0x101e0000 0x100>;
 			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -198,7 +198,7 @@
 
 		dp: dp-controller@145b0000 {
 			compatible = "samsung,exynos5-dp";
-			reg = <0x145B0000 0x1000>;
+			reg = <0x145b0000 0x1000>;
 			interrupts = <10 3>;
 			interrupt-parent = <&combiner>;
 			status = "disabled";
@@ -211,13 +211,13 @@
 		};
 
 		prng: rng@10830400 {
-		      compatible = "samsung,exynos5250-prng";
-		      reg = <0x10830400 0x200>;
+			compatible = "samsung,exynos5250-prng";
+			reg = <0x10830400 0x200>;
 		};
 
 		trng: rng@10830600 {
-		      compatible = "samsung,exynos5250-trng";
-		      reg = <0x10830600 0x100>;
+			compatible = "samsung,exynos5250-trng";
+			reg = <0x10830600 0x100>;
 		};
 
 		g2d: g2d@10850000 {
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/samsung/exynos5250-arndale.dts
index d6c85efdb465..d586189966da 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/samsung/exynos5250-arndale.dts
@@ -15,7 +15,7 @@
 #include "exynos5250.dtsi"
 
 / {
-	model = "Insignal Arndale evaluation board based on EXYNOS5250";
+	model = "Insignal Arndale evaluation board based on Exynos5250";
 	compatible = "insignal,arndale", "samsung,exynos5250", "samsung,exynos5";
 
 	memory@40000000 {
@@ -23,49 +23,54 @@
 		reg = <0x40000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		menu {
+		key-menu {
 			label = "SW-TACT2";
 			gpios = <&gpx1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			label = "SW-TACT3";
 			gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		up {
+		key-up {
 			label = "SW-TACT4";
 			gpios = <&gpx1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_UP>;
 			wakeup-source;
 		};
 
-		down {
+		key-down {
 			label = "SW-TACT5";
 			gpios = <&gpx1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DOWN>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "SW-TACT6";
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		wakeup {
+		key-wakeup {
 			label = "SW-TACT7";
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -73,6 +78,19 @@
 		};
 	};
 
+	/*
+	 * For unknown reasons HDMI-DDC does not work with Exynos I2C
+	 * controllers. Lets use software I2C over GPIO pins as a workaround.
+	 */
+	i2c_ddc: i2c-10 {
+		compatible = "i2c-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_gpio_bus>;
+		sda-gpios = <&gpa0 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpa0 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+	};
+
 	panel: panel {
 		compatible = "boe,hv070wsa-100";
 		power-supply = <&vcc_3v3_reg>;
@@ -84,56 +102,48 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		main_dc_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "MAIN_DC";
-		};
+	main_dc_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "MAIN_DC";
+		regulator-always-on;
+	};
 
-		mmc_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "VDD_33ON_2.8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	mmc_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_MMC";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
 
-		reg_hdmi_en: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "hdmi-en";
-		};
+	reg_hdmi_en: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi-en";
+		regulator-always-on;
+	};
 
-		vcc_1v2_reg: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "VCC_1V2";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
+	vcc_1v2_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
 
-		vcc_1v8_reg: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "VCC_1V8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
+	vcc_1v8_reg: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
 
-		vcc_3v3_reg: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "VCC_3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	vcc_3v3_reg: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	sound {
@@ -154,7 +164,7 @@
 		compatible = "smsc,usb3503a";
 
 		reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
-		connect-gpios = <&gpd1 7 GPIO_ACTIVE_LOW>;
+		connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -187,12 +197,15 @@
 		vddio-supply = <&vcc_1v8_reg>;
 		vddlvds-supply = <&vcc_3v3_reg>;
 		reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		port@1 {
-			reg = <1>;
-			bridge_out_ep: endpoint {
-				remote-endpoint = <&panel_ep>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@1 {
+				reg = <1>;
+				bridge_out_ep: endpoint {
+					remote-endpoint = <&panel_ep>;
+				};
 			};
 		};
 	};
@@ -219,13 +232,14 @@
 	samsung,i2c-max-bus-freq = <20000>;
 	samsung,i2c-slave-addr = <0x66>;
 
-	s5m8767_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s5m8767-pmic";
 		reg = <0x66>;
 		interrupt-parent = <&gpx3>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s5m8767_irq>;
+		wakeup-source;
 
 		vinb1-supply = <&main_dc_reg>;
 		vinb2-supply = <&main_dc_reg>;
@@ -247,15 +261,12 @@
 		vinl8-supply = <&buck8_reg>;
 		vinl9-supply = <&buck8_reg>;
 
-		s5m8767,pmic-buck2-dvs-voltage = <1300000>;
-		s5m8767,pmic-buck3-dvs-voltage = <1100000>;
-		s5m8767,pmic-buck4-dvs-voltage = <1200000>;
 		s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_HIGH>,
-		                              <&gpd1 1 GPIO_ACTIVE_HIGH>,
-		                              <&gpd1 2 GPIO_ACTIVE_HIGH>;
+					      <&gpd1 1 GPIO_ACTIVE_HIGH>,
+					      <&gpd1 2 GPIO_ACTIVE_HIGH>;
 		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>,
-		                             <&gpx2 4 GPIO_ACTIVE_HIGH>,
-		                             <&gpx2 5 GPIO_ACTIVE_HIGH>;
+					     <&gpx2 4 GPIO_ACTIVE_HIGH>,
+					     <&gpx2 5 GPIO_ACTIVE_HIGH>;
 
 		s5m8767_osc: clocks {
 			compatible = "samsung,s5m8767-clk";
@@ -450,7 +461,7 @@
 			};
 
 			buck1_reg: BUCK1 {
-				regulator-name = "vdd_mif";
+				regulator-name = "VDD_MIF";
 				regulator-min-microvolt = <950000>;
 				regulator-max-microvolt = <1200000>;
 				regulator-always-on;
@@ -459,7 +470,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "vdd_arm";
+				regulator-name = "VDD_ARM";
 				regulator-min-microvolt = <912500>;
 				regulator-max-microvolt = <1300000>;
 				regulator-always-on;
@@ -468,7 +479,7 @@
 			};
 
 			buck3_reg: BUCK3 {
-				regulator-name = "vdd_int";
+				regulator-name = "VDD_INT";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1200000>;
 				regulator-always-on;
@@ -477,7 +488,7 @@
 			};
 
 			buck4_reg: BUCK4 {
-				regulator-name = "vdd_g3d";
+				regulator-name = "VDD_G3D";
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-always-on;
@@ -519,7 +530,7 @@
 &i2c_3 {
 	status = "okay";
 
-	wm1811: codec@1a {
+	wm1811: audio-codec@1a {
 		compatible = "wlf,wm1811";
 		reg = <0x1a>;
 		clocks = <&i2s0 CLK_I2S_CDCLK>;
@@ -534,8 +545,8 @@
 		SPKVDD1-supply = <&main_dc_reg>;
 		SPKVDD2-supply = <&main_dc_reg>;
 
-		wlf,ldo1ena = <&gpb0 0 GPIO_ACTIVE_HIGH>;
-		wlf,ldo2ena = <&gpb0 1 GPIO_ACTIVE_HIGH>;
+		wlf,ldo1ena-gpios = <&gpb0 0 GPIO_ACTIVE_HIGH>;
+		wlf,ldo2ena-gpios = <&gpb0 1 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -550,12 +561,6 @@
 	status = "okay";
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-max-bus-freq = <40000>;
-	samsung,i2c-slave-addr = <0x38>;
-
-	sata_phy_i2c:sata-phy@38 {
-		compatible = "samsung,exynos-sataphy-i2c";
-		reg = <0x38>;
-	};
 };
 
 &i2s0 {
@@ -589,6 +594,7 @@
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
 };
 
 &mmc_2 {
@@ -606,7 +612,7 @@
 };
 
 &pinctrl_0 {
-	s5m8767_irq: s5m8767-irq {
+	s5m8767_irq: s5m8767-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
@@ -627,21 +633,11 @@
 	samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
 };
 
-&soc {
-	/*
-	 * For unknown reasons HDMI-DDC does not work with Exynos I2C
-	 * controllers. Lets use software I2C over GPIO pins as a workaround.
-	 */
-	i2c_ddc: i2c-gpio {
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_gpio_bus>;
-		status = "okay";
-		compatible = "i2c-gpio";
-		gpios = <&gpa0 6 0 /* sda */
-			 &gpa0 7 0 /* scl */
-			>;
-		i2c-gpio,delay-us = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
+&sata_phy_i2c {
+	status = "okay";
+};
+
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
 };
diff --git a/arch/arm/boot/dts/exynos5250-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos5250-pinctrl.dtsi
index d31a68672bfa..d956540a2d88 100644
--- a/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5250-pinctrl.dtsi
@@ -5,14 +5,14 @@
  * Copyright (c) 2012 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * Samsung's Exynos5250 SoC pin-mux and pin-config optiosn are listed as device
- * tree nodes are listed in this file.
+ * Samsung's Exynos5250 SoC pin-mux and pin-config options are listed as device
+ * tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -20,7 +20,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -28,7 +28,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -36,7 +36,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -44,7 +44,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -52,7 +52,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -60,7 +60,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -68,7 +68,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -76,7 +76,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -84,7 +84,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -92,7 +92,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -100,7 +100,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -108,7 +108,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -116,42 +116,42 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpc4: gpc4 {
+	gpc4: gpc4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -159,7 +159,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -170,7 +170,7 @@
 			     <26 0>, <26 1>, <27 0>, <27 1>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -181,7 +181,7 @@
 			     <30 0>, <30 1>, <31 0>, <31 1>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -189,7 +189,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -197,104 +197,104 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_hs_bus: i2c2-hs-bus {
+	i2c2_hs_bus: i2c2-hs-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_gpio_bus: i2c2-gpio-bus {
+	i2c2_gpio_bus: i2c2-gpio-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_hs_bus: i2c3-hs-bus {
+	i2c3_hs_bus: i2c3-hs-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
-		samsung,pins = "gpa1-4", "gpa1-4";
+	uart3_data: uart3-data-pins {
+		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -302,7 +302,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -310,7 +310,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
@@ -318,7 +318,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -326,7 +326,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -334,280 +334,280 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpb1-1", "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpb2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpb2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpb2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpb2-2", "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_hs_bus: i2c0-hs-bus {
+	i2c0_hs_bus: i2c0-hs-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_hs_bus: i2c1-hs-bus {
+	i2c1_hs_bus: i2c1-hs-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5", "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpc2-3", "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc3-3", "gpc3-4", "gpc3-5", "gpc3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpc4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpc4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpc4-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpc4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	dp_hpd: dp_hpd {
+	dp_hpd: dp-hpd-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 };
 
 &pinctrl_1 {
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -615,7 +615,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -623,7 +623,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -631,7 +631,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -639,7 +639,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -647,7 +647,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -655,7 +655,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -663,7 +663,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -671,7 +671,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -679,7 +679,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	cam_gpio_a: cam-gpio-a {
+	cam_gpio_a: cam-gpio-a-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 			       "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 			       "gpe1-0", "gpe1-1";
@@ -688,7 +688,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_b: cam-gpio-b {
+	cam_gpio_b: cam-gpio-b-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
 			       "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -696,42 +696,42 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_i2c2_bus: cam-i2c2-bus {
+	cam_i2c2_bus: cam-i2c2-bus-pins {
 		samsung,pins = "gpe0-6", "gpe1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_spi1_bus: cam-spi1-bus {
+	cam_spi1_bus: cam-spi1-bus-pins {
 		samsung,pins = "gpe0-4", "gpe0-5", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_i2c1_bus: cam-i2c1-bus {
+	cam_i2c1_bus: cam-i2c1-bus-pins {
 		samsung,pins = "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_i2c0_bus: cam-i2c0-bus {
+	cam_i2c0_bus: cam-i2c0-bus-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_spi0_bus: cam-spi0-bus {
+	cam_spi0_bus: cam-spi0-bus-pins {
 		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_bayrgb_bus: cam-bayrgb-bus {
+	cam_bayrgb_bus: cam-bayrgb-bus-pins {
 		samsung,pins = "gpg0-0", "gpg0-1", "gpg0-2", "gpg0-3",
 			       "gpg0-4", "gpg0-5", "gpg0-6", "gpg0-7",
 			       "gpg1-0", "gpg1-1", "gpg1-2", "gpg1-3",
@@ -742,7 +742,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a: cam-port-a {
+	cam_port_a: cam-port-a-pins {
 		samsung,pins = "gph0-0", "gph0-1", "gph0-2", "gph0-3",
 			       "gph1-0", "gph1-1", "gph1-2", "gph1-3",
 			       "gph1-4", "gph1-5", "gph1-6", "gph1-7";
@@ -753,7 +753,7 @@
 };
 
 &pinctrl_2 {
-	gpv0: gpv0 {
+	gpv0: gpv0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -761,7 +761,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv1: gpv1 {
+	gpv1: gpv1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -769,7 +769,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv2: gpv2 {
+	gpv2: gpv2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -777,7 +777,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv3: gpv3 {
+	gpv3: gpv3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -785,7 +785,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv4: gpv4 {
+	gpv4: gpv4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -793,7 +793,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	c2c_rxd: c2c-rxd {
+	c2c_rxd: c2c-rxd-pins {
 		samsung,pins = "gpv0-0", "gpv0-1", "gpv0-2", "gpv0-3",
 			       "gpv0-4", "gpv0-5", "gpv0-6", "gpv0-7",
 			       "gpv1-0", "gpv1-1", "gpv1-2", "gpv1-3",
@@ -803,7 +803,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	c2c_txd: c2c-txd {
+	c2c_txd: c2c-txd-pins {
 		samsung,pins = "gpv2-0", "gpv2-1", "gpv2-2", "gpv2-3",
 			       "gpv2-4", "gpv2-5", "gpv2-6", "gpv2-7",
 			       "gpv3-0", "gpv3-1", "gpv3-2", "gpv3-3",
@@ -815,7 +815,7 @@
 };
 
 &pinctrl_3 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -823,7 +823,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/samsung/exynos5250-smdk5250.dts
index 6dc96948a9cc..bb623726ef1e 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/samsung/exynos5250-smdk5250.dts
@@ -1,21 +1,24 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG SMDK5250 board device tree source
+ * Samsung SMDK5250 board device tree source
  *
  * Copyright (c) 2012 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  */
 
 /dts-v1/;
+#include <dt-bindings/clock/maxim,max77686.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "exynos5250.dtsi"
 
 / {
-	model = "SAMSUNG SMDK5250 board based on EXYNOS5250";
+	model = "Samsung SMDK5250 board based on Exynos5250";
 	compatible = "samsung,smdk5250", "samsung,exynos5250", "samsung,exynos5";
 
 	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
 	};
 
 	memory@40000000 {
@@ -117,6 +120,9 @@
 	status = "okay";
 	ddc = <&i2c_2>;
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+	vdd-supply = <&ldo8_reg>;
+	vdd_osc-supply = <&ldo10_reg>;
+	vdd_pll-supply = <&ldo8_reg>;
 };
 
 &i2c_0 {
@@ -125,17 +131,18 @@
 	samsung,i2c-max-bus-freq = <20000>;
 
 	eeprom@50 {
-		compatible = "samsung,s524ad0xd1";
+		compatible = "samsung,s524ad0xd1", "atmel,24c128";
 		reg = <0x50>;
 	};
 
-	max77686@9 {
+	max77686: pmic@9 {
 		compatible = "maxim,max77686";
 		reg = <0x09>;
 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_NONE>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77686_irq>;
+		#clock-cells = <1>;
 		wakeup-source;
 
 		voltage-regulators {
@@ -284,11 +291,11 @@
 	samsung,i2c-max-bus-freq = <20000>;
 
 	eeprom@51 {
-		compatible = "samsung,s524ad0xd1";
+		compatible = "samsung,s524ad0xd1", "atmel,24c128";
 		reg = <0x51>;
 	};
 
-	wm8994: wm8994@1a {
+	wm8994: audio-codec@1a {
 		compatible = "wlf,wm8994";
 		reg = <0x1a>;
 
@@ -324,12 +331,6 @@
 	status = "okay";
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-max-bus-freq = <40000>;
-	samsung,i2c-slave-addr = <0x38>;
-
-	sata_phy_i2c: sata-phy@38 {
-		compatible = "samsung,exynos-sataphy-i2c";
-		reg = <0x38>;
-	};
 };
 
 &i2s0 {
@@ -351,6 +352,7 @@
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
 };
 
 &mmc_2 {
@@ -368,6 +370,8 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &sata {
@@ -379,14 +383,18 @@
 	samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
 };
 
+&sata_phy_i2c {
+	status = "okay";
+};
+
 &spi_1 {
 	status = "okay";
 	cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>;
 
-	w25q80bw@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "w25x80";
+		compatible = "winbond,w25x80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <1000000>;
 
@@ -408,10 +416,15 @@
 };
 
 &pinctrl_0 {
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 };
+
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/samsung/exynos5250-snow-common.dtsi
index c952a615148e..65b000df176e 100644
--- a/arch/arm/boot/dts/exynos5250-snow-common.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5250-snow-common.dtsi
@@ -15,6 +15,9 @@
 / {
 	aliases {
 		i2c104 = &i2c_104;
+		mmc0 = &mmc_0; /* eMMC */
+		mmc1 = &mmc_2; /* SD */
+		mmc2 = &mmc_3; /* WiFi */
 	};
 
 	memory@40000000 {
@@ -32,7 +35,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq &lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -57,12 +60,9 @@
 
 	i2c-arbitrator {
 		compatible = "i2c-arb-gpio-challenge";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		i2c-parent = <&i2c_4>;
 
-		our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
+		our-claim-gpios = <&gpf0 3 GPIO_ACTIVE_LOW>;
 		their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
 		slew-delay-us = <10>;
 		wait-retry-us = <3000>;
@@ -72,8 +72,7 @@
 		pinctrl-0 = <&arb_our_claim &arb_their_claim>;
 
 		/* Use ID 104 as a hint that we're on physical bus 4 */
-		i2c_104: i2c@0 {
-			reg = <0>;
+		i2c_104: i2c-arb {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
@@ -217,7 +216,7 @@
 		};
 	};
 
-	mmc3_pwrseq: mmc3_pwrseq {
+	mmc3_pwrseq: mmc3-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */
 			      <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */
@@ -289,10 +288,10 @@
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-max-bus-freq = <378000>;
 
-	max77686: max77686@9 {
+	max77686: pmic@9 {
 		compatible = "maxim,max77686";
 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_NONE>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77686_irq>;
 		wakeup-source;
@@ -549,6 +548,7 @@
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
 };
 
 /* uSD card */
@@ -587,63 +587,63 @@
 };
 
 &pinctrl_0 {
-	wifi_en: wifi-en {
+	wifi_en: wifi-en-pins {
 		samsung,pins = "gpx0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	wifi_rst: wifi-rst {
+	wifi_rst: wifi-rst-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	tps65090_irq: tps65090-irq {
+	tps65090_irq: tps65090-irq-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	usb3_vbus_en: usb3-vbus-en {
+	usb3_vbus_en: usb3-vbus-en-pins {
 		samsung,pins = "gpx2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -652,14 +652,14 @@
 };
 
 &pinctrl_1 {
-	arb_their_claim: arb-their-claim {
+	arb_their_claim: arb-their-claim-pins {
 		samsung,pins = "gpe0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	arb_our_claim: arb-our-claim {
+	arb_our_claim: arb-our-claim-pins {
 		samsung,pins = "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -698,6 +698,11 @@
 	cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>;
 };
 
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 &usbdrd_dwc3 {
 	dr_mode = "host";
 };
@@ -706,4 +711,4 @@
 	vbus-supply = <&usb3_vbus_reg>;
 };
 
-#include "cros-ec-keyboard.dtsi"
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/exynos5250-snow-rev5.dts b/arch/arm/boot/dts/samsung/exynos5250-snow-rev5.dts
index 7cbfc6f1f4b8..3d32c3476e84 100644
--- a/arch/arm/boot/dts/exynos5250-snow-rev5.dts
+++ b/arch/arm/boot/dts/samsung/exynos5250-snow-rev5.dts
@@ -14,6 +14,7 @@
 	model = "Google Snow Rev 5+";
 	compatible = "google,snow-rev5", "samsung,exynos5250",
 		"samsung,exynos5";
+	chassis-type = "laptop";
 
 	sound {
 		compatible = "google,snow-audio-max98090";
@@ -26,13 +27,13 @@
 		};
 
 		codec {
-			sound-dai = <&max98090 0>, <&hdmi>;
+			sound-dai = <&max98090>, <&hdmi>;
 		};
 	};
 };
 
 &i2c_7 {
-	max98090: codec@10 {
+	max98090: audio-codec@10 {
 		compatible = "maxim,max98090";
 		reg = <0x10>;
 		interrupts = <4 IRQ_TYPE_NONE>;
@@ -41,12 +42,12 @@
 		pinctrl-0 = <&max98090_irq>;
 		clocks = <&pmu_system_controller 0>;
 		clock-names = "mclk";
-		#sound-dai-cells = <1>;
+		#sound-dai-cells = <0>;
 	};
 };
 
 &pinctrl_0 {
-	max98090_irq: max98090-irq {
+	max98090_irq: max98090-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/samsung/exynos5250-snow.dts
index 75fdc5e6d423..906aa7aae710 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/samsung/exynos5250-snow.dts
@@ -12,6 +12,7 @@
 	model = "Google Snow";
 	compatible = "google,snow-rev4", "google,snow", "samsung,exynos5250",
 		"samsung,exynos5";
+	chassis-type = "laptop";
 
 	sound {
 		compatible = "google,snow-audio-max98095";
@@ -30,7 +31,7 @@
 };
 
 &i2c_7 {
-	max98095: codec@11 {
+	max98095: audio-codec@11 {
 		compatible = "maxim,max98095";
 		reg = <0x11>;
 		pinctrl-names = "default";
@@ -42,7 +43,7 @@
 };
 
 &pinctrl_0 {
-	max98095_en: max98095-en {
+	max98095_en: max98095-en-pins {
 		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/samsung/exynos5250-spring.dts
index 3d501926c227..d126fccdcaf3 100644
--- a/arch/arm/boot/dts/exynos5250-spring.dts
+++ b/arch/arm/boot/dts/samsung/exynos5250-spring.dts
@@ -7,6 +7,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/clock/samsung,s2mps11.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
@@ -15,12 +16,18 @@
 / {
 	model = "Google Spring";
 	compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
+	chassis-type = "laptop";
 
 	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_1;
+	};
+
 	chosen {
 		bootargs = "console=tty1";
 		stdout-path = "serial3:115200n8";
@@ -31,7 +38,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq>, <&lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -104,22 +111,22 @@
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-max-bus-freq = <378000>;
 
-	s5m8767-pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s5m8767-pmic";
 		reg = <0x66>;
 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_NONE>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
 		wakeup-source;
 
 		s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
-		                              <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
-		                              <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+					      <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+					      <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
 
 		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
-		                             <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
-		                             <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+					     <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+					     <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
 
 		/*
 		 * The following arrays of DVS voltages are not used, since we are
@@ -127,26 +134,26 @@
 		 * to please the driver.
 		 */
 		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
-		                                 <1250000>, <1200000>,
-		                                 <1150000>, <1100000>,
-		                                 <1000000>, <950000>;
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
 
 		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
-		                                 <1100000>, <1100000>,
-		                                 <1000000>, <1000000>,
-		                                 <1000000>, <1000000>;
+						 <1100000>, <1100000>,
+						 <1000000>, <1000000>,
+						 <1000000>, <1000000>;
 
 		s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
-		                                 <1200000>, <1200000>,
-		                                 <1200000>, <1200000>,
-		                                 <1200000>, <1200000>;
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
 
-		clocks {
+		s5m8767_osc: clocks {
 			compatible = "samsung,s5m8767-clk";
 			#clock-cells = <1>;
 			clock-output-names = "en32khz_ap",
-			                     "en32khz_cp",
-			                     "en32khz_bt";
+					     "en32khz_cp",
+					     "en32khz_bt";
 		};
 
 		regulators {
@@ -429,6 +436,7 @@
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
 };
 
 /*
@@ -449,63 +457,63 @@
 };
 
 &pinctrl_0 {
-	s5m8767_dvs: s5m8767-dvs {
+	s5m8767_dvs: s5m8767-dvs-pins {
 		samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	dp_hpd_gpio: dp-hpd-gpio {
+	dp_hpd_gpio: dp-hpd-pins {
 		samsung,pins = "gpc3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	trackpad_irq: trackpad-irq {
+	trackpad_irq: trackpad-irq-pins {
 		samsung,pins = "gpx1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	s5m8767_ds: s5m8767-ds {
+	s5m8767_ds: s5m8767-ds-pins {
 		samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	s5m8767_irq: s5m8767-irq {
+	s5m8767_irq: s5m8767-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -514,7 +522,7 @@
 };
 
 &pinctrl_1 {
-	hsic_reset: hsic-reset {
+	hsic_reset: hsic-reset-pins {
 		samsung,pins = "gpe1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -522,6 +530,12 @@
 	};
 };
 
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sd1_bus4 {
 	samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 };
@@ -545,4 +559,9 @@
 	num-cs = <1>;
 };
 
-#include "cros-ec-keyboard.dtsi"
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/samsung/exynos5250.dtsi
index e1f0215e3985..99c84bebf25a 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5250.dtsi
@@ -1,16 +1,16 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5250 SoC device tree source
+ * Samsung Exynos5250 SoC device tree source
  *
  * Copyright (c) 2012 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * SAMSUNG EXYNOS5250 SoC device nodes are listed in this file.
- * EXYNOS5250 based board files can include this file and provide
- * values for board specfic bindings.
+ * Samsung Exynos5250 SoC device nodes are listed in this file.
+ * Exynos5250 based board files can include this file and provide
+ * values for board specific bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
- * EXYNOS5250 SoC. As device tree coverage for EXYNOS5250 increases,
+ * Exynos5250 SoC. As device tree coverage for Exynos5250 increases,
  * additional nodes can be added to this file.
  */
 
@@ -30,10 +30,6 @@
 		gsc1 = &gsc_1;
 		gsc2 = &gsc_2;
 		gsc3 = &gsc_3;
-		mshc0 = &mmc_0;
-		mshc1 = &mmc_1;
-		mshc2 = &mmc_2;
-		mshc3 = &mmc_3;
 		i2c4 = &i2c_4;
 		i2c5 = &i2c_5;
 		i2c6 = &i2c_6;
@@ -50,6 +46,17 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
@@ -70,7 +77,7 @@
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -171,12 +178,12 @@
 			#size-cells = <1>;
 			ranges = <0 0x02020000 0x30000>;
 
-			smp-sysram@0 {
+			smp-sram@0 {
 				compatible = "samsung,exynos4210-sysram";
 				reg = <0x0 0x1000>;
 			};
 
-			smp-sysram@2f000 {
+			smp-sram@2f000 {
 				compatible = "samsung,exynos4210-sysram-ns";
 				reg = <0x2f000 0x1000>;
 			};
@@ -205,14 +212,14 @@
 
 		pd_disp1: power-domain@100440a0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x100440A0 0x20>;
+			reg = <0x100440a0 0x20>;
 			#power-domain-cells = <0>;
 			label = "DISP1";
 		};
 
 		pd_mau: power-domain@100440c0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x100440C0 0x20>;
+			reg = <0x100440c0 0x20>;
 			#power-domain-cells = <0>;
 			label = "MAU";
 		};
@@ -225,7 +232,7 @@
 
 		clock_audss: audss-clock-controller@3810000 {
 			compatible = "samsung,exynos5250-audss-clock";
-			reg = <0x03810000 0x0C>;
+			reg = <0x03810000 0x0c>;
 			#clock-cells = <1>;
 			clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
 				 <&clock CLK_SCLK_AUDIO0>, <&clock CLK_DIV_PCM0>;
@@ -234,8 +241,9 @@
 		};
 
 		timer@101c0000 {
-			compatible = "samsung,exynos4210-mct";
-			reg = <0x101C0000 0x800>;
+			compatible = "samsung,exynos5250-mct",
+				     "samsung,exynos4210-mct";
+			reg = <0x101c0000 0x800>;
 			clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
 			clock-names = "fin_pll", "mct";
 			interrupts-extended = <&combiner 23 3>,
@@ -278,7 +286,7 @@
 		};
 
 		pmu_system_controller: system-controller@10040000 {
-			compatible = "samsung,exynos5250-pmu", "syscon";
+			compatible = "samsung,exynos5250-pmu", "simple-mfd", "syscon";
 			reg = <0x10040000 0x5000>;
 			clock-names = "clkout16";
 			clocks = <&clock CLK_FIN_PLL>;
@@ -286,11 +294,21 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			interrupt-parent = <&gic>;
+
+			dp_phy: dp-phy {
+				compatible = "samsung,exynos5250-dp-video-phy";
+				#phy-cells = <0>;
+			};
+
+			mipi_phy: mipi-phy {
+				compatible = "samsung,s5pv210-mipi-video-phy";
+				#phy-cells = <1>;
+			};
 		};
 
 		watchdog@101d0000 {
 			compatible = "samsung,exynos5250-wdt";
-			reg = <0x101D0000 0x100>;
+			reg = <0x101d0000 0x100>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_WDT>;
 			clock-names = "watchdog";
@@ -310,7 +328,7 @@
 
 		rotator: rotator@11c00000 {
 			compatible = "samsung,exynos5250-rotator";
-			reg = <0x11C00000 0x64>;
+			reg = <0x11c00000 0x64>;
 			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_ROTATOR>;
 			clock-names = "rotator";
@@ -330,7 +348,7 @@
 			power-domains = <&pd_g3d>;
 			status = "disabled";
 
-			gpu_opp_table: gpu-opp-table {
+			gpu_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-100000000 {
@@ -375,11 +393,10 @@
 
 		sata: sata@122f0000 {
 			compatible = "snps,dwc-ahci";
-			samsung,sata-freq = <66>;
-			reg = <0x122F0000 0x1ff>;
+			reg = <0x122f0000 0x1ff>;
 			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>;
-			clock-names = "sata", "sclk_sata";
+			clock-names = "sata", "pclk";
 			phys = <&sata_phy>;
 			phy-names = "sata-phy";
 			ports-implemented = <0x1>;
@@ -399,7 +416,7 @@
 		/* i2c_0-3 are defined in exynos5.dtsi */
 		i2c_4: i2c@12ca0000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12CA0000 0x100>;
+			reg = <0x12ca0000 0x100>;
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -412,7 +429,7 @@
 
 		i2c_5: i2c@12cb0000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12CB0000 0x100>;
+			reg = <0x12cb0000 0x100>;
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -425,7 +442,7 @@
 
 		i2c_6: i2c@12cc0000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12CC0000 0x100>;
+			reg = <0x12cc0000 0x100>;
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -438,7 +455,7 @@
 
 		i2c_7: i2c@12cd0000 {
 			compatible = "samsung,s3c2440-i2c";
-			reg = <0x12CD0000 0x100>;
+			reg = <0x12cd0000 0x100>;
 			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -451,7 +468,7 @@
 
 		i2c_8: i2c@12ce0000 {
 			compatible = "samsung,s3c2440-hdmiphy-i2c";
-			reg = <0x12CE0000 0x1000>;
+			reg = <0x12ce0000 0x1000>;
 			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -459,7 +476,7 @@
 			clock-names = "i2c";
 			status = "disabled";
 
-			hdmiphy: hdmiphy@38 {
+			hdmiphy: hdmi-phy@38 {
 				compatible = "samsung,exynos4212-hdmiphy";
 				reg = <0x38>;
 			};
@@ -467,12 +484,18 @@
 
 		i2c_9: i2c@121d0000 {
 			compatible = "samsung,exynos5-sata-phy-i2c";
-			reg = <0x121D0000 0x100>;
+			reg = <0x121d0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&clock CLK_SATA_PHYI2C>;
 			clock-names = "i2c";
 			status = "disabled";
+
+			sata_phy_i2c: sata-phy-i2c@38 {
+				compatible = "samsung,exynos-sataphy-i2c";
+				reg = <0x38>;
+				status = "disabled";
+			};
 		};
 
 		spi_0: spi@12d20000 {
@@ -480,8 +503,7 @@
 			status = "disabled";
 			reg = <0x12d20000 0x100>;
 			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&pdma0 5
-				&pdma0 4>;
+			dmas = <&pdma0 5>, <&pdma0 4>;
 			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -496,8 +518,7 @@
 			status = "disabled";
 			reg = <0x12d30000 0x100>;
 			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&pdma1 5
-				&pdma1 4>;
+			dmas = <&pdma1 5>, <&pdma1 4>;
 			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -512,8 +533,7 @@
 			status = "disabled";
 			reg = <0x12d40000 0x100>;
 			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&pdma0 7
-				&pdma0 6>;
+			dmas = <&pdma0 7>, <&pdma0 6>;
 			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -594,7 +614,7 @@
 		i2s1: i2s@12d60000 {
 			compatible = "samsung,s3c6410-i2s";
 			status = "disabled";
-			reg = <0x12D60000 0x100>;
+			reg = <0x12d60000 0x100>;
 			dmas = <&pdma1 12>,
 				<&pdma1 11>;
 			dma-names = "tx", "rx";
@@ -609,7 +629,7 @@
 		i2s2: i2s@12d70000 {
 			compatible = "samsung,s3c6410-i2s";
 			status = "disabled";
-			reg = <0x12D70000 0x100>;
+			reg = <0x12d70000 0x100>;
 			dmas = <&pdma0 12>,
 				<&pdma0 11>;
 			dma-names = "tx", "rx";
@@ -621,17 +641,17 @@
 			#sound-dai-cells = <1>;
 		};
 
-		usb_dwc3 {
+		usbdrd: usb@12000000 {
 			compatible = "samsung,exynos5250-dwusb3";
 			clocks = <&clock CLK_USB3>;
 			clock-names = "usbdrd30";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x0 0x12000000 0x10000>;
 
-			usbdrd_dwc3: dwc3@12000000 {
-				compatible = "synopsys,dwc3";
-				reg = <0x12000000 0x10000>;
+			usbdrd_dwc3: usb@0 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x10000>;
 				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usbdrd_phy 0>, <&usbdrd_phy 1>;
 				phy-names = "usb2-phy", "usb3-phy";
@@ -679,59 +699,43 @@
 			samsung,pmureg-phandle = <&pmu_system_controller>;
 		};
 
-		amba {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			interrupt-parent = <&gic>;
-			ranges;
-
-			pdma0: pdma@121a0000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x121A0000 0x1000>;
-				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma0: dma-controller@121a0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x121a0000 0x1000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			pdma1: pdma@121b0000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x121B0000 0x1000>;
-				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma1: dma-controller@121b0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x121b0000 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			mdma0: mdma@10800000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x10800000 0x1000>;
-				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_MDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <1>;
-			};
+		mdma0: dma-controller@10800000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x10800000 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_MDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			mdma1: mdma@11c10000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x11C10000 0x1000>;
-				interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_MDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <1>;
-			};
+		mdma1: dma-controller@11c10000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x11c10000 0x1000>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_MDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
 		};
 
-		gsc_0:  gsc@13e00000 {
+		gsc_0: gsc@13e00000 {
 			compatible = "samsung,exynos5250-gsc", "samsung,exynos5-gsc";
 			reg = <0x13e00000 0x1000>;
 			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
@@ -741,7 +745,7 @@
 			iommus = <&sysmmu_gsc0>;
 		};
 
-		gsc_1:  gsc@13e10000 {
+		gsc_1: gsc@13e10000 {
 			compatible = "samsung,exynos5250-gsc", "samsung,exynos5-gsc";
 			reg = <0x13e10000 0x1000>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
@@ -751,7 +755,7 @@
 			iommus = <&sysmmu_gsc1>;
 		};
 
-		gsc_2:  gsc@13e20000 {
+		gsc_2: gsc@13e20000 {
 			compatible = "samsung,exynos5250-gsc", "samsung,exynos5-gsc";
 			reg = <0x13e20000 0x1000>;
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
@@ -761,7 +765,7 @@
 			iommus = <&sysmmu_gsc2>;
 		};
 
-		gsc_3:  gsc@13e30000 {
+		gsc_3: gsc@13e30000 {
 			compatible = "samsung,exynos5250-gsc", "samsung,exynos5-gsc";
 			reg = <0x13e30000 0x1000>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
@@ -789,7 +793,7 @@
 
 		hdmicec: cec@101b0000 {
 			compatible = "samsung,s5p-cec";
-			reg = <0x101B0000 0x200>;
+			reg = <0x101b0000 0x200>;
 			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_HDMI_CEC>;
 			clock-names = "hdmicec";
@@ -812,19 +816,6 @@
 			status = "disabled";
 		};
 
-		dp_phy: video-phy {
-			compatible = "samsung,exynos5250-dp-video-phy";
-			samsung,pmu-syscon = <&pmu_system_controller>;
-			#phy-cells = <0>;
-		};
-
-		mipi_phy: video-phy@10040710 {
-			compatible = "samsung,s5pv210-mipi-video-phy";
-			reg = <0x10040710 0x100>;
-			#phy-cells = <1>;
-			syscon = <&pmu_system_controller>;
-		};
-
 		dsi_0: dsi@14500000 {
 			compatible = "samsung,exynos4210-mipi-dsi";
 			reg = <0x14500000 0x10000>;
@@ -841,19 +832,18 @@
 
 		adc: adc@12d10000 {
 			compatible = "samsung,exynos-adc-v1";
-			reg = <0x12D10000 0x100>;
+			reg = <0x12d10000 0x100>;
 			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_ADC>;
 			clock-names = "adc";
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 			samsung,syscon-phandle = <&pmu_system_controller>;
 			status = "disabled";
 		};
 
 		sysmmu_g2d: sysmmu@10a60000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x10A60000 0x1000>;
+			reg = <0x10a60000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <24 5>;
 			clock-names = "sysmmu", "master";
@@ -885,7 +875,7 @@
 
 		sysmmu_rotator: sysmmu@11d40000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11D40000 0x1000>;
+			reg = <0x11d40000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 0>;
 			clock-names = "sysmmu", "master";
@@ -895,7 +885,7 @@
 
 		sysmmu_jpeg: sysmmu@11f20000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11F20000 0x1000>;
+			reg = <0x11f20000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 2>;
 			power-domains = <&pd_gsc>;
@@ -926,7 +916,7 @@
 
 		sysmmu_fimc_fd: sysmmu@132a0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x132A0000 0x1000>;
+			reg = <0x132a0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <5 0>;
 			clock-names = "sysmmu";
@@ -956,7 +946,7 @@
 
 		sysmmu_fimc_mcuctl: sysmmu@132b0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x132B0000 0x1000>;
+			reg = <0x132b0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <5 4>;
 			clock-names = "sysmmu";
@@ -966,7 +956,7 @@
 
 		sysmmu_fimc_odc: sysmmu@132c0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x132C0000 0x1000>;
+			reg = <0x132c0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <11 0>;
 			clock-names = "sysmmu";
@@ -976,7 +966,7 @@
 
 		sysmmu_fimc_dis0: sysmmu@132d0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x132D0000 0x1000>;
+			reg = <0x132d0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <10 4>;
 			clock-names = "sysmmu";
@@ -986,7 +976,7 @@
 
 		sysmmu_fimc_dis1: sysmmu@132e0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x132E0000 0x1000>;
+			reg = <0x132e0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <9 4>;
 			clock-names = "sysmmu";
@@ -996,7 +986,7 @@
 
 		sysmmu_fimc_3dnr: sysmmu@132f0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x132F0000 0x1000>;
+			reg = <0x132f0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <5 6>;
 			clock-names = "sysmmu";
@@ -1006,7 +996,7 @@
 
 		sysmmu_fimc_lite0: sysmmu@13c40000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13C40000 0x1000>;
+			reg = <0x13c40000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <3 4>;
 			power-domains = <&pd_gsc>;
@@ -1017,7 +1007,7 @@
 
 		sysmmu_fimc_lite1: sysmmu@13c50000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13C50000 0x1000>;
+			reg = <0x13c50000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <24 1>;
 			power-domains = <&pd_gsc>;
@@ -1028,7 +1018,7 @@
 
 		sysmmu_gsc0: sysmmu@13e80000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13E80000 0x1000>;
+			reg = <0x13e80000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <2 0>;
 			power-domains = <&pd_gsc>;
@@ -1039,7 +1029,7 @@
 
 		sysmmu_gsc1: sysmmu@13e90000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13E90000 0x1000>;
+			reg = <0x13e90000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <2 2>;
 			power-domains = <&pd_gsc>;
@@ -1050,7 +1040,7 @@
 
 		sysmmu_gsc2: sysmmu@13ea0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13EA0000 0x1000>;
+			reg = <0x13ea0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <2 4>;
 			power-domains = <&pd_gsc>;
@@ -1061,7 +1051,7 @@
 
 		sysmmu_gsc3: sysmmu@13eb0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13EB0000 0x1000>;
+			reg = <0x13eb0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <2 6>;
 			power-domains = <&pd_gsc>;
@@ -1093,26 +1083,6 @@
 		};
 	};
 
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			polling-delay-passive = <0>;
-			polling-delay = <0>;
-			thermal-sensors = <&tmu 0>;
-
-			cooling-maps {
-				map0 {
-				     /* Corresponds to 800MHz at freq_table */
-				     cooling-device = <&cpu0 9 9>, <&cpu1 9 9>;
-				};
-				map1 {
-				     /* Corresponds to 200MHz at freq_table */
-				     cooling-device = <&cpu0 15 15>,
-						      <&cpu1 15 15>;
-			       };
-		       };
-		};
-	};
-
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -1128,6 +1098,24 @@
 	};
 };
 
+&cpu_thermal {
+	polling-delay-passive = <0>;
+	polling-delay = <0>;
+	thermal-sensors = <&tmu>;
+
+	cooling-maps {
+		map0 {
+			/* Corresponds to 800MHz at freq_table */
+			cooling-device = <&cpu0 9 9>, <&cpu1 9 9>;
+		};
+		map1 {
+			/* Corresponds to 200MHz at freq_table */
+			cooling-device = <&cpu0 15 15>,
+					 <&cpu1 15 15>;
+		};
+	};
+};
+
 &dp {
 	power-domains = <&pd_disp1>;
 	clocks = <&clock CLK_DP>;
diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos5260-pinctrl.dtsi
index 17e2f3e0d71e..d15494b4bda9 100644
--- a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5260-pinctrl.dtsi
@@ -6,13 +6,13 @@
  *		http://www.samsung.com
  *
  * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device
- * tree nodes are listed in this file.
+ * tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -20,7 +20,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -28,7 +28,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -36,7 +36,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -44,7 +44,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -52,7 +52,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -60,7 +60,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -68,7 +68,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb4: gpb4 {
+	gpb4: gpb4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -76,7 +76,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb5: gpb5 {
+	gpb5: gpb5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -84,7 +84,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -92,7 +92,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -100,7 +100,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd2: gpd2 {
+	gpd2: gpd2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -108,7 +108,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -116,7 +116,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -124,7 +124,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -132,7 +132,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -140,7 +140,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -148,7 +148,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -164,7 +164,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -180,7 +180,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -188,7 +188,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -196,63 +196,63 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	usb3_vbus0_en: usb3-vbus0-en {
+	usb3_vbus0_en: usb3-vbus0-en-pins {
 		samsung,pins = "gpa2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 				"gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -260,7 +260,7 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 				"gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -268,105 +268,105 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spdif1_bus: spdif1-bus {
+	spdif1_bus: spdif1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c0_hs_bus: i2c0-hs-bus {
+	i2c0_hs_bus: i2c0-hs-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c1_hs_bus: i2c1-hs-bus {
+	i2c1_hs_bus: i2c1-hs-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c2_hs_bus: i2c2-hs-bus {
+	i2c2_hs_bus: i2c2-hs-bus-pins {
 		samsung,pins = "gpb3-4", "gpb3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c3_hs_bus: i2c3-hs-bus {
+	i2c3_hs_bus: i2c3-hs-bus-pins {
 		samsung,pins = "gpb3-6", "gpb3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb4-0", "gpb4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb4-2", "gpb4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpb4-4", "gpb4-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpb4-6", "gpb4-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c8_bus: i2c8-bus {
+	i2c8_bus: i2c8-bus-pins {
 		samsung,pins = "gpb5-0", "gpb5-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c9_bus: i2c9-bus {
+	i2c9_bus: i2c9-bus-pins {
 		samsung,pins = "gpb5-2", "gpb5-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c10_bus: i2c10-bus {
+	i2c10_bus: i2c10-bus-pins {
 		samsung,pins = "gpb5-4", "gpb5-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c11_bus: i2c11-bus {
+	i2c11_bus: i2c11-bus-pins {
 		samsung,pins = "gpb5-6", "gpb5-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_a: cam-gpio-a {
+	cam_gpio_a: cam-gpio-a-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 			"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 			"gpe1-0", "gpe1-1";
@@ -375,7 +375,7 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_b: cam-gpio-b {
+	cam_gpio_b: cam-gpio-b-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
 			"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -383,28 +383,28 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_i2c1_bus: cam-i2c1-bus {
+	cam_i2c1_bus: cam-i2c1-bus-pins {
 		samsung,pins = "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_i2c0_bus: cam-i2c0-bus {
+	cam_i2c0_bus: cam-i2c0-bus-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_spi0_bus: cam-spi0-bus {
+	cam_spi0_bus: cam-spi0-bus-pins {
 		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_spi1_bus: cam-spi1-bus {
+	cam_spi1_bus: cam-spi1-bus-pins {
 		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -413,7 +413,7 @@
 };
 
 &pinctrl_1 {
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -421,7 +421,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -429,7 +429,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -437,7 +437,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -445,7 +445,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc4: gpc4 {
+	gpc4: gpc4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -453,112 +453,112 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_rdqs: sd0-rdqs {
+	sd0_rdqs: sd0-rdqs-pins {
 		samsung,pins = "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpc1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpc1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_bus8: sd1-bus-width8 {
+	sd1_bus8: sd1-bus-width8-pins {
 		samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -567,7 +567,7 @@
 };
 
 &pinctrl_2 {
-	gpz0: gpz0 {
+	gpz0: gpz0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -575,7 +575,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpz1: gpz1 {
+	gpz1: gpz1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
diff --git a/arch/arm/boot/dts/exynos5260-xyref5260.dts b/arch/arm/boot/dts/samsung/exynos5260-xyref5260.dts
index 36a2b77eeb9d..d072a7398866 100644
--- a/arch/arm/boot/dts/exynos5260-xyref5260.dts
+++ b/arch/arm/boot/dts/samsung/exynos5260-xyref5260.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG XYREF5260 board device tree source
+ * Samsung XYREF5260 board device tree source
  *
  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -10,7 +10,7 @@
 #include "exynos5260.dtsi"
 
 / {
-	model = "SAMSUNG XYREF5260 board based on EXYNOS5260";
+	model = "Samsung XYREF5260 board based on Exynos5260";
 	compatible = "samsung,xyref5260", "samsung,exynos5260", "samsung,exynos5";
 
 	memory@20000000 {
@@ -18,6 +18,11 @@
 		reg = <0x20000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
@@ -29,6 +34,27 @@
 		#clock-cells = <0>;
 	};
 
+	ioclk_pcm: clock-pcm-ext {
+		compatible = "fixed-clock";
+		clock-frequency = <2048000>;
+		clock-output-names = "ioclk_pcm_extclk";
+		#clock-cells = <0>;
+	};
+
+	ioclk_i2s: clock-i2s-cd {
+		compatible = "fixed-clock";
+		clock-frequency = <147456000>;
+		clock-output-names = "ioclk_i2s_cdclk";
+		#clock-cells = <0>;
+	};
+
+	ioclk_spdif: clock-spdif-ext {
+		compatible = "fixed-clock";
+		clock-frequency = <49152000>;
+		clock-output-names = "ioclk_spdif_extclk";
+		#clock-cells = <0>;
+	};
+
 	xrtcxti: xrtcxti {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
@@ -38,7 +64,7 @@
 };
 
 &pinctrl_0 {
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -66,8 +92,9 @@
 	status = "okay";
 	broken-cd;
 	cap-mmc-highspeed;
-	supports-hs200-mode; /* 200 MHz */
+	mmc-hs200-1_8v;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <0 4>;
 	samsung,dw-mshc-ddr-timing = <0 2>;
diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/samsung/exynos5260.dtsi
index b0811dbbb362..a97449b4640c 100644
--- a/arch/arm/boot/dts/exynos5260.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5260.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5260 SoC device tree source
+ * Samsung Exynos5260 SoC device tree source
  *
  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -34,42 +34,68 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu2>;
+				};
+				core1 {
+					cpu = <&cpu3>;
+				};
+				core2 {
+					cpu = <&cpu4>;
+				};
+				core3 {
+					cpu = <&cpu5>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x0>;
 			cci-control-port = <&cci_control1>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x1>;
 			cci-control-port = <&cci_control1>;
 		};
 
-		cpu@100 {
+		cpu2: cpu@100 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0x100>;
 			cci-control-port = <&cci_control0>;
 		};
 
-		cpu@101 {
+		cpu3: cpu@101 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0x101>;
 			cci-control-port = <&cci_control0>;
 		};
 
-		cpu@102 {
+		cpu4: cpu@102 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0x102>;
 			cci-control-port = <&cci_control0>;
 		};
 
-		cpu@103 {
+		cpu5: cpu@103 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0x103>;
@@ -87,85 +113,211 @@
 			compatible = "samsung,exynos5260-clock-top";
 			reg = <0x10010000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_mif MIF_DOUT_MEM_PLL>,
+				 <&clock_mif MIF_DOUT_BUS_PLL>,
+				 <&clock_mif MIF_DOUT_MEDIA_PLL>;
+			clock-names = "fin_pll",
+				      "dout_mem_pll",
+				      "dout_bus_pll",
+				      "dout_media_pll";
 		};
 
 		clock_peri: clock-controller@10200000 {
 			compatible = "samsung,exynos5260-clock-peri";
 			reg = <0x10200000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&ioclk_pcm>,
+				 <&ioclk_i2s>,
+				 <&ioclk_spdif>,
+				 <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_PERI_66>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_UART0>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_UART1>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_UART2>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_SPI0_B>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_SPI1_B>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_SPI2_B>,
+				 <&clock_top TOP_DOUT_ACLK_PERI_AUD>;
+			clock-names = "fin_pll",
+				      "ioclk_pcm_extclk",
+				      "ioclk_i2s_cdclk",
+				      "ioclk_spdif_extclk",
+				      "phyclk_hdmi_phy_ref_cko",
+				      "dout_aclk_peri_66",
+				      "dout_sclk_peri_uart0",
+				      "dout_sclk_peri_uart1",
+				      "dout_sclk_peri_uart2",
+				      "dout_sclk_peri_spi0_b",
+				      "dout_sclk_peri_spi1_b",
+				      "dout_sclk_peri_spi2_b",
+				      "dout_aclk_peri_aud";
 		};
 
 		clock_egl: clock-controller@10600000 {
 			compatible = "samsung,exynos5260-clock-egl";
 			reg = <0x10600000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_mif MIF_DOUT_BUS_PLL>;
+			clock-names = "fin_pll",
+				      "dout_bus_pll";
 		};
 
 		clock_kfc: clock-controller@10700000 {
 			compatible = "samsung,exynos5260-clock-kfc";
 			reg = <0x10700000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_mif MIF_DOUT_MEDIA_PLL>;
+			clock-names = "fin_pll",
+				      "dout_media_pll";
 		};
 
 		clock_g2d: clock-controller@10a00000 {
 			compatible = "samsung,exynos5260-clock-g2d";
-			reg = <0x10A00000 0x10000>;
+			reg = <0x10a00000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_G2D_333>;
+			clock-names = "fin_pll",
+				      "dout_aclk_g2d_333";
 		};
 
 		clock_mif: clock-controller@10ce0000 {
 			compatible = "samsung,exynos5260-clock-mif";
-			reg = <0x10CE0000 0x10000>;
+			reg = <0x10ce0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
 		};
 
 		clock_mfc: clock-controller@11090000 {
 			compatible = "samsung,exynos5260-clock-mfc";
 			reg = <0x11090000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_MFC_333>;
+			clock-names = "fin_pll",
+				      "dout_aclk_mfc_333";
 		};
 
 		clock_g3d: clock-controller@11830000 {
 			compatible = "samsung,exynos5260-clock-g3d";
 			reg = <0x11830000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
 		};
 
 		clock_fsys: clock-controller@122e0000 {
 			compatible = "samsung,exynos5260-clock-fsys";
-			reg = <0x122E0000 0x10000>;
+			reg = <0x122e0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_FSYS_200>;
+			clock-names = "fin_pll",
+				      "phyclk_usbhost20_phy_phyclock",
+				      "phyclk_usbhost20_phy_freeclk",
+				      "phyclk_usbhost20_phy_clk48mohci",
+				      "phyclk_usbdrd30_udrd30_pipe_pclk",
+				      "phyclk_usbdrd30_udrd30_phyclock",
+				      "dout_aclk_fsys_200";
 		};
 
 		clock_aud: clock-controller@128c0000 {
 			compatible = "samsung,exynos5260-clock-aud";
-			reg = <0x128C0000 0x10000>;
+			reg = <0x128c0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_FOUT_AUD_PLL>,
+				 <&ioclk_i2s>,
+				 <&ioclk_pcm>;
+			clock-names = "fin_pll",
+				      "fout_aud_pll",
+				      "ioclk_i2s_cdclk",
+				      "ioclk_pcm_extclk";
 		};
 
 		clock_isp: clock-controller@133c0000 {
 			compatible = "samsung,exynos5260-clock-isp";
-			reg = <0x133C0000 0x10000>;
+			reg = <0x133c0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_ISP1_266>,
+				 <&clock_top TOP_DOUT_ACLK_ISP1_400>,
+				 <&clock_top TOP_MOUT_ACLK_ISP1_266>;
+			clock-names = "fin_pll",
+				      "dout_aclk_isp1_266",
+				      "dout_aclk_isp1_400",
+				      "mout_aclk_isp1_266";
 		};
 
 		clock_gscl: clock-controller@13f00000 {
 			compatible = "samsung,exynos5260-clock-gscl";
-			reg = <0x13F00000 0x10000>;
+			reg = <0x13f00000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_GSCL_400>,
+				 <&clock_top TOP_DOUT_ACLK_GSCL_333>;
+			clock-names = "fin_pll",
+				      "dout_aclk_gscl_400",
+				      "dout_aclk_gscl_333";
 		};
 
 		clock_disp: clock-controller@14550000 {
 			compatible = "samsung,exynos5260-clock-disp";
 			reg = <0x14550000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&ioclk_spdif>,
+				 <&clock_top TOP_DOUT_ACLK_PERI_AUD>,
+				 <&clock_top TOP_DOUT_ACLK_DISP_222>,
+				 <&clock_top TOP_DOUT_SCLK_DISP_PIXEL>,
+				 <&clock_top TOP_DOUT_ACLK_DISP_333>;
+			clock-names = "fin_pll",
+				      "phyclk_dptx_phy_ch3_txd_clk",
+				      "phyclk_dptx_phy_ch2_txd_clk",
+				      "phyclk_dptx_phy_ch1_txd_clk",
+				      "phyclk_dptx_phy_ch0_txd_clk",
+				      "phyclk_hdmi_phy_tmds_clko",
+				      "phyclk_hdmi_phy_ref_clko",
+				      "phyclk_hdmi_phy_pixel_clko",
+				      "phyclk_hdmi_link_o_tmds_clkhi",
+				      "phyclk_mipi_dphy_4l_m_txbyte_clkhs",
+				      "phyclk_dptx_phy_o_ref_clk_24m",
+				      "phyclk_dptx_phy_clk_div2",
+				      "phyclk_mipi_dphy_4l_m_rxclkesc0",
+				      "phyclk_hdmi_phy_ref_cko",
+				      "ioclk_spdif_extclk",
+				      "dout_aclk_peri_aud",
+				      "dout_aclk_disp_222",
+				      "dout_sclk_disp_pixel",
+				      "dout_aclk_disp_333";
 		};
 
 		gic: interrupt-controller@10481000 {
-			compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+			compatible = "arm,gic-400", "arm,cortex-a15-gic";
 			#interrupt-cells = <3>;
-			#address-cells = <0>;
-			#size-cells = <0>;
 			interrupt-controller;
 			reg = <0x10481000 0x1000>,
 				<0x10482000 0x2000>,
@@ -181,8 +333,9 @@
 		};
 
 		mct: timer@100b0000 {
-			compatible = "samsung,exynos4210-mct";
-			reg = <0x100B0000 0x1000>;
+			compatible = "samsung,exynos5260-mct",
+				     "samsung,exynos4210-mct";
+			reg = <0x100b0000 0x1000>;
 			clocks = <&fin_pll>, <&clock_peri PERI_CLK_MCT>;
 			clock-names = "fin_pll", "mct";
 			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
@@ -203,8 +356,8 @@
 			compatible = "arm,cci-400";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			reg = <0x10F00000 0x1000>;
-			ranges = <0x0 0x10F00000 0x6000>;
+			reg = <0x10f00000 0x1000>;
+			ranges = <0x0 0x10f00000 0x6000>;
 
 			cci_control0: slave-if@4000 {
 				compatible = "arm,cci-400-ctrl-if";
@@ -239,18 +392,18 @@
 
 		pinctrl_2: pinctrl@128b0000 {
 			compatible = "samsung,exynos5260-pinctrl";
-			reg = <0x128B0000 0x1000>;
+			reg = <0x128b0000 0x1000>;
 			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		pmu_system_controller: system-controller@10d50000 {
 			compatible = "samsung,exynos5260-pmu", "syscon";
-			reg = <0x10D50000 0x10000>;
+			reg = <0x10d50000 0x10000>;
 		};
 
 		uart0: serial@12c00000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C00000 0x100>;
+			reg = <0x12c00000 0x100>;
 			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri PERI_SCLK_UART0>;
 			clock-names = "uart", "clk_uart_baud0";
@@ -259,7 +412,7 @@
 
 		uart1: serial@12c10000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C10000 0x100>;
+			reg = <0x12c10000 0x100>;
 			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri PERI_SCLK_UART1>;
 			clock-names = "uart", "clk_uart_baud0";
@@ -268,7 +421,7 @@
 
 		uart2: serial@12c20000 {
 			compatible = "samsung,exynos4210-uart";
-			reg = <0x12C20000 0x100>;
+			reg = <0x12c20000 0x100>;
 			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri PERI_SCLK_UART2>;
 			clock-names = "uart", "clk_uart_baud0";
@@ -344,9 +497,9 @@
 			status = "disabled";
 		};
 
-		hsi2c_0: hsi2c@12da0000 {
+		hsi2c_0: i2c@12da0000 {
 			compatible = "samsung,exynos5260-hsi2c";
-			reg = <0x12DA0000 0x1000>;
+			reg = <0x12da0000 0x1000>;
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -357,9 +510,9 @@
 			status = "disabled";
 		};
 
-		hsi2c_1: hsi2c@12db0000 {
+		hsi2c_1: i2c@12db0000 {
 			compatible = "samsung,exynos5260-hsi2c";
-			reg = <0x12DB0000 0x1000>;
+			reg = <0x12db0000 0x1000>;
 			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -370,9 +523,9 @@
 			status = "disabled";
 		};
 
-		hsi2c_2: hsi2c@12dc0000 {
+		hsi2c_2: i2c@12dc0000 {
 			compatible = "samsung,exynos5260-hsi2c";
-			reg = <0x12DC0000 0x1000>;
+			reg = <0x12dc0000 0x1000>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -383,9 +536,9 @@
 			status = "disabled";
 		};
 
-		hsi2c_3: hsi2c@12dd0000 {
+		hsi2c_3: i2c@12dd0000 {
 			compatible = "samsung,exynos5260-hsi2c";
-			reg = <0x12DD0000 0x1000>;
+			reg = <0x12dd0000 0x1000>;
 			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/samsung/exynos5410-odroidxu.dts
index e0db251e253f..882fc77c4bc4 100644
--- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ b/arch/arm/boot/dts/samsung/exynos5410-odroidxu.dts
@@ -19,6 +19,12 @@
 	model = "Hardkernel Odroid XU";
 	compatible = "hardkernel,odroid-xu", "samsung,exynos5410", "samsung,exynos5";
 
+	aliases {
+		ethernet = &ethernet;
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
+	};
+
 	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x7ea00000>;
@@ -109,14 +115,13 @@
 	assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
 			<&clock_audss EXYNOS_MOUT_AUDSS>;
 
-	assigned-clock-rates =  <0>,
-				<0>,
-				<96000000>,
-				<19200000>;
+	assigned-clock-rates = <0>,
+			       <0>,
+			       <96000000>,
+			       <19200000>;
 };
 
 &cpu0_thermal {
-	thermal-sensors = <&tmu_cpu0 0>;
 	polling-delay-passive = <0>;
 	polling-delay = <0>;
 
@@ -160,8 +165,7 @@
 };
 
 &hsi2c_4 {
-	samsung,i2c-sda-delay = <100>;
-	samsung,i2c-max-bus-freq = <400000>;
+	clock-frequency = <400000>;
 	status = "okay";
 
 	usb3503: usb-hub@8 {
@@ -170,7 +174,7 @@
 
 		intn-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
 		connect-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpx1 4 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpx1 4 GPIO_ACTIVE_LOW>;
 		initial-mode = <1>;
 
 		clock-names = "refclk";
@@ -184,8 +188,8 @@
 		interrupt-parent = <&gpx0>;
 		interrupts = <4 IRQ_TYPE_NONE>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&max77802_irq>, <&pmic_dvs_1>, <&pmic_dvs_2>,
-			    <&pmic_dvs_3>;
+		pinctrl-0 = <&max77802_irq>, <&pmic_dvs_1>, <&pmic_dvs_2>;
+		wakeup-source;
 		#clock-cells = <1>;
 
 		inl1-supply = <&buck5_reg>;
@@ -327,6 +331,8 @@
 				regulator-name = "vddq_lcd";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				/* Supplies also GPK and GPJ */
+				regulator-always-on;
 			};
 
 			ldo8_reg: LDO8 {
@@ -387,10 +393,6 @@
 				regulator-always-on;
 			};
 
-			ldo16_reg: LDO16 {
-				regulator-name = "ldo16";
-			};
-
 			ldo17_reg: LDO17 {
 				regulator-name = "cam_sensor_core";
 				regulator-min-microvolt = <1200000>;
@@ -420,10 +422,6 @@
 				regulator-max-microvolt = <2850000>;
 			};
 
-			ldo22_reg: LDO22 {
-				regulator-name = "ldo22";
-			};
-
 			ldo23_reg: LDO23 {
 				regulator-name = "dp_p3v3";
 				regulator-min-microvolt = <3300000>;
@@ -470,10 +468,6 @@
 				regulator-always-on;
 			};
 
-			ldo31_reg: LDO31 {
-				regulator-name = "ldo31";
-			};
-
 			/* On revisions with ti,ina231 this is sensor VS */
 			ldo32_reg: LDO32 {
 				regulator-name = "vs_power_meter";
@@ -498,7 +492,7 @@
 
 &i2c_1 {
 	status = "okay";
-	max98090: max98090@10 {
+	max98090: audio-codec@10 {
 		compatible = "maxim,max98090";
 		reg = <0x10>;
 		interrupt-parent = <&gpj3>;
@@ -521,6 +515,7 @@
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	vmmc-supply = <&ldo20_reg>;
 	vqmmc-supply = <&ldo11_reg>;
@@ -541,14 +536,14 @@
 };
 
 &pinctrl_0 {
-	emmc_nrst_pin: emmc-nrst {
+	emmc_nrst_pin: emmc-nrst-pins {
 		samsung,pins = "gpd1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	sd2_wp: sd2-wp {
+	sd2_wp: sd2-wp-pins {
 		samsung,pins = "gpm5-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		/* Pin is floating so be sure to disable write-protect */
@@ -556,21 +551,14 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	pmic_dvs_3: pmic-dvs-3 {
-		samsung,pins = "gpx0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
-	};
-
-	pmic_dvs_2: pmic-dvs-2 {
-		samsung,pins = "gpx0-1";
+	pmic_dvs_2: pmic-dvs-2-pins {
+		samsung,pins = "gpx0-0", "gpx0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_dvs_1: pmic-dvs-1 {
+	pmic_dvs_1: pmic-dvs-1-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -578,7 +566,7 @@
 		samsung,pin-val = <1>;
 	};
 
-	max77802_irq: max77802-irq {
+	max77802_irq: max77802-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -636,12 +624,22 @@
 	vtmu-supply = <&ldo10_reg>;
 };
 
+&usb3_0_oc {
+	/* External pull up */
+	samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+};
+
+&usb3_1_oc {
+	/* External pull up */
+	samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+};
+
 &usbdrd_dwc3_0 {
-	dr_mode = "host";
+	dr_mode = "peripheral";
 };
 
 &usbdrd_dwc3_1 {
-	dr_mode = "peripheral";
+	dr_mode = "host";
 };
 
 &usbdrd3_0 {
@@ -653,3 +651,14 @@
 	vdd33-supply = <&ldo12_reg>;
 	vdd10-supply = <&ldo15_reg>;
 };
+
+&usbhost2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ethernet: ethernet@2 {
+		compatible = "usb424,9730";
+		reg = <2>;
+		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos5410-pinctrl.dtsi
index 369a8a7f2105..f7b923382892 100644
--- a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5410-pinctrl.dtsi
@@ -3,13 +3,13 @@
  * Exynos5410 SoC pin-mux and pin-config device tree source
  *
  * Copyright (c) 2013 Hardkernel Co., Ltd.
- *              http://www.hardkernel.com
+ *              https://www.hardkernel.com
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -17,7 +17,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -25,7 +25,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -33,7 +33,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -41,7 +41,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -49,7 +49,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -57,7 +57,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -65,7 +65,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -73,7 +73,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -81,7 +81,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -89,7 +89,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -97,12 +97,12 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm5: gpm5 {
+	gpm5: gpm5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -110,7 +110,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -118,7 +118,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -126,7 +126,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -134,7 +134,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -142,7 +142,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -150,7 +150,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -158,7 +158,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -166,7 +166,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -174,7 +174,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -182,52 +182,52 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm7: gpm7 {
+	gpm7: gpm7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy7: gpy7 {
+	gpy7: gpy7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -235,16 +235,16 @@
 		interrupt-parent = <&combiner>;
 		#interrupt-cells = <2>;
 		interrupts = <23 0>,
-		             <24 0>,
-		             <25 0>,
-		             <25 1>,
-		             <26 0>,
-		             <26 1>,
-		             <27 0>,
-		             <27 1>;
+			     <24 0>,
+			     <25 0>,
+			     <25 1>,
+			     <26 0>,
+			     <26 1>,
+			     <27 0>,
+			     <27 1>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -252,16 +252,16 @@
 		interrupt-parent = <&combiner>;
 		#interrupt-cells = <2>;
 		interrupts = <28 0>,
-		             <28 1>,
-		             <29 0>,
-		             <29 1>,
-		             <30 0>,
-		             <30 1>,
-		             <31 0>,
-		             <31 1>;
+			     <28 1>,
+			     <29 0>,
+			     <29 1>,
+			     <30 0>,
+			     <30 1>,
+			     <31 0>,
+			     <31 1>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -269,7 +269,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -277,210 +277,210 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c4_hs_bus: i2c4-hs-bus {
+	i2c4_hs_bus: i2c4-hs-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c5_hs_bus: i2c5-hs-bus {
+	i2c5_hs_bus: i2c5-hs-bus-pins {
 		samsung,pins = "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c6_hs_bus: i2c6-hs-bus {
+	i2c6_hs_bus: i2c6-hs-bus-pins {
 		samsung,pins = "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpb2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpb2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpb2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c7_hs_bus: i2c7-hs-bus {
+	i2c7_hs_bus: i2c7-hs-bus-pins {
 		samsung,pins = "gpb2-2", "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-4", "gpc0-5", "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -489,7 +489,7 @@
 };
 
 &pinctrl_1 {
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -497,7 +497,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -505,7 +505,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj2: gpj2 {
+	gpj2: gpj2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -513,7 +513,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj3: gpj3 {
+	gpj3: gpj3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -521,7 +521,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj4: gpj4 {
+	gpj4: gpj4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -529,7 +529,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -537,7 +537,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -545,7 +545,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -553,17 +553,45 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk3: gpk3 {
+	gpk3: gpk3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
+
+	usb3_1_oc: usb3-1-oc-pins {
+		samsung,pins = "gpk2-4", "gpk2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	usb3_1_vbusctrl: usb3-1-vbusctrl-pins {
+		samsung,pins = "gpk2-6", "gpk2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	usb3_0_oc: usb3-0-oc-pins {
+		samsung,pins = "gpk3-0", "gpk3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	usb3_0_vbusctrl: usb3-0-vbusctrl-pins {
+		samsung,pins = "gpk3-2", "gpk3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
 };
 
 &pinctrl_2 {
-	gpv0: gpv0 {
+	gpv0: gpv0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -571,7 +599,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv1: gpv1 {
+	gpv1: gpv1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -579,7 +607,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv2: gpv2 {
+	gpv2: gpv2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -587,7 +615,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv3: gpv3 {
+	gpv3: gpv3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -595,7 +623,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv4: gpv4 {
+	gpv4: gpv4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -605,7 +633,7 @@
 };
 
 &pinctrl_3 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -613,7 +641,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	audi2s0_bus: audi2s0-bus {
+	audi2s0_bus: audi2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4";
 		samsung,pin-function = <2>;
diff --git a/arch/arm/boot/dts/exynos5410-smdk5410.dts b/arch/arm/boot/dts/samsung/exynos5410-smdk5410.dts
index dffa5e3ed90c..bb29b76f6f6a 100644
--- a/arch/arm/boot/dts/exynos5410-smdk5410.dts
+++ b/arch/arm/boot/dts/samsung/exynos5410-smdk5410.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG SMDK5410 board device tree source
+ * Samsung SMDK5410 board device tree source
  *
  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -10,7 +10,7 @@
 #include "exynos5410.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 / {
-	model = "Samsung SMDK5410 board based on EXYNOS5410";
+	model = "Samsung SMDK5410 board based on Exynos5410";
 	compatible = "samsung,smdk5410", "samsung,exynos5410", "samsung,exynos5";
 
 	memory@40000000 {
@@ -18,6 +18,11 @@
 		reg = <0x40000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
@@ -29,11 +34,31 @@
 		#clock-cells = <0>;
 	};
 
+	pmic_ap_clk: pmic-ap-clk {
+		/* Workaround for missing PMIC and its clock */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
 	firmware@2037000 {
 		compatible = "samsung,secure-firmware";
 		reg = <0x02037000 0x1000>;
 	};
 
+	vdd10_usb3: voltage-regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD10_USB3";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+	vdd33_usb3: voltage-regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD33_USB3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &mmc_0 {
@@ -41,6 +66,7 @@
 	cap-mmc-highspeed;
 	broken-cd;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <2 3>;
 	samsung,dw-mshc-ddr-timing = <1 2>;
@@ -59,14 +85,14 @@
 };
 
 &pinctrl_0 {
-	srom_ctl: srom-ctl {
+	srom_ctl: srom-ctl-pins {
 		samsung,pins = "gpy0-3", "gpy0-4", "gpy0-5",
 			       "gpy1-0", "gpy1-1", "gpy1-2", "gpy1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	srom_ebi: srom-ebi {
+	srom_ebi: srom-ebi-pins {
 		samsung,pins = "gpy3-0", "gpy3-1", "gpy3-2", "gpy3-3",
 			       "gpy3-4", "gpy3-5", "gpy3-6", "gpy3-7",
 			       "gpy5-0", "gpy5-1", "gpy5-2", "gpy5-3",
@@ -79,6 +105,11 @@
 	};
 };
 
+&rtc {
+	clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sromc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&srom_ctl>, <&srom_ebi>;
@@ -109,3 +140,13 @@
 &serial_2 {
 	status = "okay";
 };
+
+&usbdrd3_0 {
+	vdd10-supply = <&vdd10_usb3>;
+	vdd33-supply = <&vdd33_usb3>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&vdd10_usb3>;
+	vdd33-supply = <&vdd33_usb3>;
+};
diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/samsung/exynos5410.dtsi
index a4b03d4c3de5..546035e78f40 100644
--- a/arch/arm/boot/dts/exynos5410.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5410.dtsi
@@ -1,13 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5410 SoC device tree source
+ * Samsung Exynos5410 SoC device tree source
  *
  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * SAMSUNG EXYNOS5410 SoC device nodes are listed in this file.
- * EXYNOS5410 based board files can include this file and provide
- * values for board specfic bindings.
+ * Samsung Exynos5410 SoC device nodes are listed in this file.
+ * Exynos5410 based board files can include this file and provide
+ * values for board specific bindings.
  */
 
 #include "exynos54xx.dtsi"
@@ -81,7 +81,7 @@
 
 		clock_audss: audss-clock-controller@3810000 {
 			compatible = "samsung,exynos5410-audss-clock";
-			reg = <0x03810000 0x0C>;
+			reg = <0x03810000 0x0c>;
 			#clock-cells = <1>;
 			clocks = <&fin_pll>, <&clock CLK_FOUT_EPLL>;
 			clock-names = "pll_ref", "pll_in";
@@ -189,34 +189,22 @@
 			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		amba {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			interrupt-parent = <&gic>;
-			ranges;
-
-			pdma0: pdma@121a0000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x121a0000 0x1000>;
-				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma0: dma-controller@121a0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x121a0000 0x1000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			pdma1: pdma@121b0000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x121b0000 0x1000>;
-				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma1: dma-controller@121b0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x121b0000 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
 		};
 
 		audi2s0: i2s@3830000 {
@@ -246,16 +234,16 @@
 			#include "exynos5420-trip-points.dtsi"
 		};
 		cpu1_thermal: cpu1-thermal {
-		       thermal-sensors = <&tmu_cpu1>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_cpu1>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 		cpu2_thermal: cpu2-thermal {
-		       thermal-sensors = <&tmu_cpu2>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_cpu2>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 		cpu3_thermal: cpu3-thermal {
-		       thermal-sensors = <&tmu_cpu3>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_cpu3>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 	};
 };
@@ -398,6 +386,8 @@
 &usbdrd3_0 {
 	clocks = <&clock CLK_USBD300>;
 	clock-names = "usbdrd30";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb3_0_oc>, <&usb3_0_vbusctrl>;
 };
 
 &usbdrd_phy0 {
@@ -409,6 +399,8 @@
 &usbdrd3_1 {
 	clocks = <&clock CLK_USBD301>;
 	clock-names = "usbdrd30";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb3_1_oc>, <&usb3_1_vbusctrl>;
 };
 
 &usbdrd_dwc3_1 {
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/samsung/exynos5420-arndale-octa.dts
index 592d7b45ecc8..809ddda02e53 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/samsung/exynos5420-arndale-octa.dts
@@ -15,7 +15,7 @@
 #include <dt-bindings/clock/samsung,s2mps11.h>
 
 / {
-	model = "Insignal Arndale Octa evaluation board based on EXYNOS5420";
+	model = "Insignal Arndale Octa evaluation board based on Exynos5420";
 	compatible = "insignal,arndale-octa", "samsung,exynos5420", "samsung,exynos5";
 
 	memory@20000000 {
@@ -23,6 +23,11 @@
 		reg = <0x20000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
+	};
+
 	chosen {
 		stdout-path = "serial3:115200n8";
 	};
@@ -39,10 +44,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SW-TACT1";
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -344,14 +349,15 @@
 &hsi2c_4 {
 	status = "okay";
 
-	s2mps11_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s2mps11-pmic";
 		reg = <0x66>;
 
 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s2mps11_irq>;
+		wakeup-source;
 
 		s2mps11_osc: clocks {
 			compatible = "samsung,s2mps11-clk";
@@ -584,6 +590,7 @@
 				regulator-name = "PVDD_G3DS_1V0";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -672,7 +679,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "vdd_arm";
+				regulator-name = "PVDD_ARM_1V0";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
@@ -697,6 +704,7 @@
 				regulator-name = "PVDD_G3D_1V0";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -775,6 +783,7 @@
 	status = "okay";
 	non-removable;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <0 4>;
 	samsung,dw-mshc-ddr-timing = <0 2>;
@@ -805,7 +814,7 @@
 };
 
 &pinctrl_0 {
-	s2mps11_irq: s2mps11-irq {
+	s2mps11_irq: s2mps11-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -822,3 +831,13 @@
 &usbdrd_dwc3_1 {
 	dr_mode = "host";
 };
+
+&usbdrd3_0 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
diff --git a/arch/arm/boot/dts/samsung/exynos5420-chagall-wifi.dts b/arch/arm/boot/dts/samsung/exynos5420-chagall-wifi.dts
new file mode 100644
index 000000000000..1319344a2c74
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos5420-chagall-wifi.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos5420 Chagall WiFi board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420-galaxy-tab-common.dtsi"
+
+/ {
+	model = "Samsung Chagall WiFi based on Exynos5420";
+	compatible = "samsung,chagall-wifi", "samsung,exynos5420", \
+		     "samsung,exynos5";
+};
+
+&ldo15_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO15";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+&ldo17_reg {
+	regulator-name = "VDD_IRLED_3V3";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3350000>;
+	regulator-always-on;
+	regulator-boot-on;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo28_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO28";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+&ldo29_reg {
+	regulator-name = "VDD_TCON_1V8";
+	regulator-min-microvolt = <1900000>;
+	regulator-max-microvolt = <1900000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo31_reg {
+	regulator-name = "VDD_GRIP_1V8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+	regulator-boot-on;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo32_reg {
+	regulator-name = "VDD_TSP_1V8";
+	regulator-min-microvolt = <1900000>;
+	regulator-max-microvolt = <1900000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5420-cpus.dtsi b/arch/arm/boot/dts/samsung/exynos5420-cpus.dtsi
index 0ee6e92a3c29..e9f4eb75b50f 100644
--- a/arch/arm/boot/dts/exynos5420-cpus.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5420-cpus.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5420 SoC cpu device tree source
+ * Samsung Exynos5420 SoC cpu device tree source
  *
  * Copyright (c) 2015 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -22,6 +22,38 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
diff --git a/arch/arm/boot/dts/samsung/exynos5420-galaxy-tab-common.dtsi b/arch/arm/boot/dts/samsung/exynos5420-galaxy-tab-common.dtsi
new file mode 100644
index 000000000000..f525b2f5e4e0
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos5420-galaxy-tab-common.dtsi
@@ -0,0 +1,696 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Base DT for Samsung's family of tablets based on Exynos5420.
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420.dtsi"
+#include "exynos5420-cpus.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/samsung,s2mps11.h>
+
+/ {
+	chassis-type = "tablet";
+
+	/*
+	 * To successfully boot the mainline kernel with the stock
+	 * bootloader (SBOOT), the tlb needs to be flushed after the
+	 * page table pointer has been updated in __common_mmu_cache_on.
+	 * The same hack is also needed to boot exynos4412-i9300 with
+	 * stock bootloader, and probably other Samsung devices of
+	 * similar age.  See
+	 * https://lore.kernel.org/all/1355276466-18295-1-git-send-email-arve@android.com
+	 * for more details.
+	 */
+
+	aliases {
+		mmc0 = &mmc_0;
+		mmc2 = &mmc_2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0xc0000000>;
+	};
+
+	firmware@2073000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x02073000 0x1000>;
+	};
+
+	fixed-rate-clocks {
+		oscclk {
+			compatible = "samsung,exynos5420-oscclk";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			debounce-interval = <10>;
+			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-home {
+			debounce-interval = <10>;
+			gpios = <&gpx0 5 GPIO_ACTIVE_LOW>;
+			label = "Home";
+			linux,code = <KEY_HOME>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			debounce-interval = <10>;
+			gpios = <&gpx0 2 GPIO_ACTIVE_LOW>;
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			debounce-interval = <10>;
+			gpios = <&gpx0 3 GPIO_ACTIVE_LOW>;
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+};
+
+&cci {
+	/* CCI is disabled in hardware */
+	status = "disabled";
+};
+
+&cpu0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&cpu4 {
+	cpu-supply = <&buck6_reg>;
+};
+
+&gpu {
+	status = "okay";
+	mali-supply = <&buck4_reg>;
+};
+
+&hsi2c_7 {
+	status = "okay";
+
+	pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+
+		interrupt-parent = <&gpx3>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&s2mps11_irq>;
+
+		s2mps11_osc: clocks {
+			compatible = "samsung,s2mps11-clk";
+			#clock-cells = <1>;
+			clock-output-names = "s2mps11_ap", "s2mps11_cp",
+					     "s2mps11_bt";
+		};
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF_1V1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_ARM_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_INT_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_G3D_1V0";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "VDD_MEM_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "VDD_KFC_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "VIN_LLDO_1V4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "VIN_MLDO_2V0";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-always-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "VIN_HLDO_3V5";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3500000>;
+				regulator-always-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "VDD_CAM_ISP_1V0";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3550000>;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ALIVE_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_APIO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "VDD_APIO_MMC01_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "VDD_ADC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo5_reg: LDO5 {
+				/* Unused */
+				regulator-name = "VDD_LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "VDD_MIPI_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "VDD_MIPI_PLL_ABB1_18V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo8_reg: LDO8 {
+				/* Unused */
+				regulator-name = "VDD_LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "VDD_UOTG_3V0";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "VDDQ_PRE_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "VDD_HSIC_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "VDD_HSIC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "VDD_APIO_MMC2_2V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo14_reg: LDO14 {
+				regulator-name = "VDD_MOTOR_3V0";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "VDD_LDO15";
+				/*
+				 * LDO15 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "VDD_AP_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "VDD_LDO17";
+				/*
+				 * LDO17 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo18_reg: LDO18 {
+				/* Unused */
+				regulator-name = "VDD_LDO18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "VDD_VTF_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "VDD_CAM1_CAM_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "VDD_CAM_IO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo22_reg: LDO22 {
+				regulator-name = "VDD_CAM0_S_CORE_1V1";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "VDD_MIFS_1V1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "VDD_TSP_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo25_reg: LDO25 {
+				/* Unused */
+				regulator-name = "VDD_LDO25";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "VDD_CAM0_AF_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "VDD_G3DS_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo28_reg: LDO28 {
+				regulator-name = "VDD_LDO28";
+				/*
+				 * LDO28 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo29_reg: LDO29 {
+				regulator-name = "VDD_LDO29";
+				/*
+				 * LDO29 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo30_reg: LDO30 {
+				regulator-name = "VDD_TOUCH_1V8";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo31_reg: LDO31 {
+				regulator-name = "VDD_LDO31";
+				/*
+				 * LDO31 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo32_reg: LDO32 {
+				regulator-name = "VDD_LDO32";
+				/*
+				 * LDO32 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo33_reg: LDO33 {
+				regulator-name = "VDD_MHL_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo34_reg: LDO34 {
+				regulator-name = "VDD_MHL_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo35_reg: LDO35 {
+				regulator-name = "VDD_SIL_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo36_reg: LDO36 {
+				/* Unused */
+				regulator-name = "VDD_LDO36";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo37_reg: LDO37 {
+				/* Unused */
+				regulator-name = "VDD_LDO37";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo38_reg: LDO38 {
+				regulator-name = "VDD_KEY_LED_3V3";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&mixer {
+	status = "okay";
+};
+
+/* Internal storage */
+&mmc_0 {
+	status = "okay";
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+	pinctrl-names = "default";
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	vqmmc-supply = <&ldo3_reg>;
+};
+
+/* External sdcard */
+&mmc_2 {
+	status = "okay";
+	bus-width = <4>;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	cd-gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &mmc2_cd &sd2_bus1 &sd2_bus4>;
+	pinctrl-names = "default";
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	sd-uhs-sdr50;
+	vmmc-supply = <&ldo19_reg>;
+	vqmmc-supply = <&ldo13_reg>;
+};
+
+&pinctrl_0 {
+	mmc2_cd: mmc2-cd-pins {
+		samsung,pins = "gpx2-4";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	s2mps11_irq: s2mps11-irq-pins {
+		samsung,pins = "gpx3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&tmu_cpu0 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_gpu {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&usbdrd_dwc3_0 {
+	dr_mode = "peripheral";
+};
+
+&usbdrd_dwc3_1 {
+	dr_mode = "peripheral";
+};
+
+&usbdrd3_0 {
+	vdd33-supply = <&ldo9_reg>;
+	vdd10-supply = <&ldo11_reg>;
+};
+
+&usbdrd3_1 {
+	vdd33-supply = <&ldo9_reg>;
+	vdd10-supply = <&ldo11_reg>;
+};
diff --git a/arch/arm/boot/dts/samsung/exynos5420-klimt-wifi.dts b/arch/arm/boot/dts/samsung/exynos5420-klimt-wifi.dts
new file mode 100644
index 000000000000..011787b1bbf0
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos5420-klimt-wifi.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos5420 Klimt WiFi board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420-galaxy-tab-common.dtsi"
+
+/ {
+	model = "Samsung Klimt WiFi based on Exynos5420";
+	compatible = "samsung,klimt-wifi", "samsung,exynos5420", \
+		     "samsung,exynos5";
+};
+
+&ldo15_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO15";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+&ldo17_reg {
+	regulator-name = "VDD_VCI_3V0";
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo28_reg {
+	regulator-name = "VDD3_1V8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo29_reg {
+	regulator-name = "VDDR_1V6";
+	regulator-min-microvolt = <1600000>;
+	regulator-max-microvolt = <1600000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo31_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO31";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&ldo32_reg {
+	regulator-name = "VDD_TSP_1V8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&mmc_2 {
+	sd-uhs-sdr104;
+};
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/samsung/exynos5420-peach-pit.dts
index 2bcbdf8a39bf..4e757b6e28e1 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/samsung/exynos5420-peach-pit.dts
@@ -26,10 +26,14 @@
 		"google,pit-rev7", "google,pit-rev6",
 		"google,pit", "google,peach","samsung,exynos5420",
 		"samsung,exynos5";
+	chassis-type = "laptop";
 
 	aliases {
 		/* Assign 20 so we don't get confused w/ builtin ones */
 		i2c20 = &i2c_tunnel;
+		mmc0 = &mmc_0; /* eMMC */
+		mmc1 = &mmc_2; /* uSD */
+		mmc2 = &mmc_1; /* WiFi */
 	};
 
 	backlight: backlight {
@@ -59,7 +63,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq &lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -138,7 +142,7 @@
 		};
 	};
 
-	mmc1_pwrseq: mmc1_pwrseq {
+	mmc1_pwrseq: mmc1-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpx0 0 GPIO_ACTIVE_LOW>; /* WIFI_EN */
 		clocks = <&max77802 MAX77802_CLK_32K_CP>;
@@ -205,13 +209,13 @@
 	status = "okay";
 	clock-frequency = <400000>;
 
-	max77802: max77802-pmic@9 {
+	max77802: pmic@9 {
 		compatible = "maxim,max77802";
 		interrupt-parent = <&gpx3>;
 		interrupts = <1 IRQ_TYPE_NONE>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77802_irq>, <&pmic_selb>,
-			    <&pmic_dvs_1>, <&pmic_dvs_2>, <&pmic_dvs_3>;
+			    <&pmic_dvs_1>, <&pmic_dvs_2>;
 		wakeup-source;
 		reg = <0x9>;
 		#clock-cells = <1>;
@@ -615,7 +619,7 @@
 	status = "okay";
 	clock-frequency = <400000>;
 
-	max98090: codec@10 {
+	max98090: audio-codec@10 {
 		compatible = "maxim,max98090";
 		reg = <0x10>;
 		interrupts = <2 IRQ_TYPE_NONE>;
@@ -721,6 +725,7 @@
 /* eMMC flash */
 &mmc_0 {
 	status = "okay";
+	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	cap-mmc-highspeed;
 	non-removable;
@@ -773,14 +778,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mask_tpm_reset>;
 
-	wifi_en: wifi-en {
+	wifi_en: wifi-en-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max98090_irq: max98090-irq {
+	max98090_irq: max98090-irq-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -788,7 +793,7 @@
 	};
 
 	/* We need GPX0_6 to be low at sleep time; just keep it low always */
-	mask_tpm_reset: mask-tpm-reset {
+	mask_tpm_reset: mask-tpm-reset-pins {
 		samsung,pins = "gpx0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -796,70 +801,70 @@
 		samsung,pin-val = <0>;
 	};
 
-	tpm_irq: tpm-irq {
+	tpm_irq: tpm-irq-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	trackpad_irq: trackpad-irq {
+	trackpad_irq: trackpad-irq-pins {
 		samsung,pins = "gpx1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	tps65090_irq: tps65090-irq {
+	tps65090_irq: tps65090-irq-pins {
 		samsung,pins = "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	dp_hpd_gpio: dp_hpd_gpio {
+	dp_hpd_gpio: dp-hpd-gpio-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max77802_irq: max77802-irq {
+	max77802_irq: max77802-irq-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_dvs_1: pmic-dvs-1 {
+	pmic_dvs_1: pmic-dvs-1-pins {
 		samsung,pins = "gpy7-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -867,74 +872,67 @@
 	};
 };
 
-&pinctrl_1 {
-	/* Adjust WiFi drive strengths lower for EMI */
-	sd1_clk: sd1-clk {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+/* pinctrl_1 */
+/* Adjust WiFi drive strengths lower for EMI */
+&sd1_bus1 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_cmd: sd1-cmd {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus4 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus1: sd1-bus-width1 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus8 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus4: sd1-bus-width4 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_clk {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus8: sd1-bus-width8 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_cmd {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_2 {
-	pmic_dvs_2: pmic-dvs-2 {
-		samsung,pins = "gpj4-2";
+	pmic_dvs_2: pmic-dvs-2-pins {
+		samsung,pins = "gpj4-2", "gpj4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
+};
 
-	pmic_dvs_3: pmic-dvs-3 {
-		samsung,pins = "gpj4-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
-	};
+/* pinctrl_3*/
+/* Drive SPI lines at x2 for better integrity */
+&spi2_bus {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_3 {
-	/* Drive SPI lines at x2 for better integrity */
-	spi2-bus {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
-
 	/* Drive SPI chip select at x2 for better integrity */
-	ec_spi_cs: ec-spi-cs {
+	ec_spi_cs: ec-spi-cs-pins {
 		samsung,pins = "gpb1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 	};
 
-	usb300_vbus_en: usb300-vbus-en {
+	usb300_vbus_en: usb300-vbus-en-pins {
 		samsung,pins = "gph0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb301_vbus_en: usb301-vbus-en {
+	usb301_vbus_en: usb301-vbus-en-pins {
 		samsung,pins = "gph0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_selb: pmic-selb {
+	pmic_selb: pmic-selb-pins {
 		samsung,pins = "gph0-2", "gph0-3", "gph0-4", "gph0-5",
 			       "gph0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -1089,6 +1087,16 @@
 	vtmu-supply = <&ldo10_reg>;
 };
 
+&usbdrd3_0 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 &usbdrd_dwc3_0 {
 	dr_mode = "host";
 };
@@ -1114,5 +1122,5 @@
 	timeout-sec = <32>;
 };
 
-#include "cros-ec-keyboard.dtsi"
-#include "cros-adc-thermistors.dtsi"
+#include "../cros-ec-keyboard.dtsi"
+#include "../cros-adc-thermistors.dtsi"
diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/samsung/exynos5420-pinctrl.dtsi
index b82af7c89654..93b9873fa84f 100644
--- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5420-pinctrl.dtsi
@@ -6,13 +6,13 @@
  *		http://www.samsung.com
  *
  * Samsung's Exynos5420 SoC pin-mux and pin-config options are listed as device
- * tree nodes are listed in this file.
+ * tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpy7: gpy7 {
+	gpy7: gpy7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -20,7 +20,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -31,7 +31,7 @@
 			     <26 0>, <26 1>, <27 0>, <27 1>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -42,7 +42,7 @@
 			     <30 0>, <30 1>, <31 0>, <31 1>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -50,7 +50,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -58,14 +58,14 @@
 		#interrupt-cells = <2>;
 	};
 
-	dp_hpd: dp_hpd {
+	dp_hpd: dp-hpd-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -74,7 +74,7 @@
 };
 
 &pinctrl_1 {
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -82,7 +82,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -90,7 +90,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -98,7 +98,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -106,7 +106,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc4: gpc4 {
+	gpc4: gpc4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -114,7 +114,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -122,175 +122,175 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-4", "gpc0-5", "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_rclk: sd0-rclk {
+	sd0_rclk: sd0-rclk-pins {
 		samsung,pins = "gpc0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpc1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpc1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_int: sd1-int {
+	sd1_int: sd1-int-pins {
 		samsung,pins = "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpc1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpc1-4", "gpc1-5", "gpc1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_bus8: sd1-bus-width8 {
+	sd1_bus8: sd1-bus-width8-pins {
 		samsung,pins = "gpd1-4", "gpd1-5", "gpd1-6", "gpd1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_wp: sd2-wp {
+	sd2_wp: sd2-wp-pins {
 		samsung,pins = "gpc4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -299,7 +299,7 @@
 };
 
 &pinctrl_2 {
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -307,7 +307,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -315,7 +315,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -323,7 +323,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -331,7 +331,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -339,7 +339,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -347,7 +347,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -355,7 +355,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj4: gpj4 {
+	gpj4: gpj4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -363,7 +363,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	cam_gpio_a: cam-gpio-a {
+	cam_gpio_a: cam-gpio-a-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 			       "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 			       "gpe1-0", "gpe1-1";
@@ -372,7 +372,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_b: cam-gpio-b {
+	cam_gpio_b: cam-gpio-b-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
 			       "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -380,42 +380,42 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_i2c2_bus: cam-i2c2-bus {
+	cam_i2c2_bus: cam-i2c2-bus-pins {
 		samsung,pins = "gpf0-4", "gpf0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_spi1_bus: cam-spi1-bus {
+	cam_spi1_bus: cam-spi1-bus-pins {
 		samsung,pins = "gpe0-4", "gpe0-5", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_i2c1_bus: cam-i2c1-bus {
+	cam_i2c1_bus: cam-i2c1-bus-pins {
 		samsung,pins = "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_i2c0_bus: cam-i2c0-bus {
+	cam_i2c0_bus: cam-i2c0-bus-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_spi0_bus: cam-spi0-bus {
+	cam_spi0_bus: cam-spi0-bus-pins {
 		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_bayrgb_bus: cam-bayrgb-bus {
+	cam_bayrgb_bus: cam-bayrgb-bus-pins {
 		samsung,pins = "gpg0-0", "gpg0-1", "gpg0-2", "gpg0-3",
 			       "gpg0-4", "gpg0-5", "gpg0-6", "gpg0-7",
 			       "gpg1-0", "gpg1-1", "gpg1-2", "gpg1-3",
@@ -428,7 +428,7 @@
 };
 
 &pinctrl_3 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -436,7 +436,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -444,7 +444,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -452,7 +452,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -460,7 +460,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -468,7 +468,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -476,7 +476,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -484,7 +484,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb4: gpb4 {
+	gpb4: gpb4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -492,7 +492,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -500,98 +500,98 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1", "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c4_hs_bus: i2c4-hs-bus {
+	i2c4_hs_bus: i2c4-hs-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c5_hs_bus: i2c5-hs-bus {
+	i2c5_hs_bus: i2c5-hs-bus-pins {
 		samsung,pins = "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -599,7 +599,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -607,7 +607,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -615,7 +615,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -623,91 +623,91 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpb1-1", "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c6_hs_bus: i2c6-hs-bus {
+	i2c6_hs_bus: i2c6-hs-bus-pins {
 		samsung,pins = "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpb2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpb2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpb2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c7_hs_bus: i2c7-hs-bus {
+	i2c7_hs_bus: i2c7-hs-bus-pins {
 		samsung,pins = "gpb2-2", "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c8_hs_bus: i2c8-hs-bus {
+	i2c8_hs_bus: i2c8-hs-bus-pins {
 		samsung,pins = "gpb3-4", "gpb3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c9_hs_bus: i2c9-hs-bus {
+	i2c9_hs_bus: i2c9-hs-bus-pins {
 		samsung,pins = "gpb3-6", "gpb3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c10_hs_bus: i2c10-hs-bus {
+	i2c10_hs_bus: i2c10-hs-bus-pins {
 		samsung,pins = "gpb4-0", "gpb4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -716,7 +716,7 @@
 };
 
 &pinctrl_4 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -724,7 +724,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/samsung/exynos5420-smdk5420.dts
index 8240e5186972..e299344e427a 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/samsung/exynos5420-smdk5420.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG SMDK5420 board device tree source
+ * Samsung SMDK5420 board device tree source
  *
  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -9,10 +9,11 @@
 /dts-v1/;
 #include "exynos5420.dtsi"
 #include "exynos5420-cpus.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
 #include <dt-bindings/gpio/gpio.h>
 
 / {
-	model = "Samsung SMDK5420 board based on EXYNOS5420";
+	model = "Samsung SMDK5420 board based on Exynos5420";
 	compatible = "samsung,smdk5420", "samsung,exynos5420", "samsung,exynos5";
 
 	memory@20000000 {
@@ -20,6 +21,11 @@
 		reg = <0x20000000 0x80000000>;
 	};
 
+	aliases {
+		mmc0 = &mmc_0;
+		mmc1 = &mmc_2;
+	};
+
 	chosen {
 		bootargs = "init=/linuxrc";
 		stdout-path = "serial2:115200n8";
@@ -32,40 +38,31 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd: fixed-regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vdd-supply";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
+	vdd: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
 
-		dbvdd: fixed-regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "dbvdd-supply";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	dbvdd: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "dbvdd-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		spkvdd: fixed-regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "spkvdd-supply";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	spkvdd: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "spkvdd-supply";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
 	};
 
-	usb300_vbus_reg: regulator-usb300 {
+	usb300_vbus_reg: regulator-3 {
 		compatible = "regulator-fixed";
 		regulator-name = "VBUS0";
 		regulator-min-microvolt = <5000000>;
@@ -76,7 +73,7 @@
 		enable-active-high;
 	};
 
-	usb301_vbus_reg: regulator-usb301 {
+	usb301_vbus_reg: regulator-4 {
 		compatible = "regulator-fixed";
 		regulator-name = "VBUS1";
 		regulator-min-microvolt = <5000000>;
@@ -132,14 +129,18 @@
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_hpd_irq>;
+	vdd-supply = <&ldo6_reg>;
+	vdd_osc-supply = <&ldo7_reg>;
+	vdd_pll-supply = <&ldo6_reg>;
 };
 
 &hsi2c_4 {
 	status = "okay";
 
-	s2mps11_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s2mps11-pmic";
 		reg = <0x66>;
+		wakeup-source;
 
 		s2mps11_osc: clocks {
 			compatible = "samsung,s2mps11-clk";
@@ -359,6 +360,7 @@
 	status = "okay";
 	broken-cd;
 	card-detect-delay = <200>;
+	mmc-ddr-1_8v;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <0 4>;
 	samsung,dw-mshc-ddr-timing = <0 2>;
@@ -384,7 +386,7 @@
 };
 
 &pinctrl_0 {
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -393,14 +395,14 @@
 };
 
 &pinctrl_2 {
-	usb300_vbus_en: usb300-vbus-en {
+	usb300_vbus_en: usb300-vbus-en-pins {
 		samsung,pins = "gpg0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb301_vbus_en: usb301-vbus-en {
+	usb301_vbus_en: usb301-vbus-en-pins {
 		samsung,pins = "gpg1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -410,6 +412,18 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&usbdrd3_0 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
 };
 
 &usbdrd_phy0 {
diff --git a/arch/arm/boot/dts/exynos5420-trip-points.dtsi b/arch/arm/boot/dts/samsung/exynos5420-trip-points.dtsi
index a67a380717ec..a67a380717ec 100644
--- a/arch/arm/boot/dts/exynos5420-trip-points.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5420-trip-points.dtsi
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/samsung/exynos5420.dtsi
index d39907a41f78..25ed90374679 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5420.dtsi
@@ -1,13 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5420 SoC device tree source
+ * Samsung Exynos5420 SoC device tree source
  *
  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * SAMSUNG EXYNOS5420 SoC device nodes are listed in this file.
- * EXYNOS5420 based board files can include this file and provide
- * values for board specfic bindings.
+ * Samsung Exynos5420 SoC device nodes are listed in this file.
+ * Exynos5420 based board files can include this file and provide
+ * values for board specific bindings.
  */
 
 #include "exynos54xx.dtsi"
@@ -19,9 +19,6 @@
 	compatible = "samsung,exynos5420", "samsung,exynos5";
 
 	aliases {
-		mshc0 = &mmc_0;
-		mshc1 = &mmc_1;
-		mshc2 = &mmc_2;
 		pinctrl0 = &pinctrl_0;
 		pinctrl1 = &pinctrl_1;
 		pinctrl2 = &pinctrl_2;
@@ -37,78 +34,189 @@
 		spi2 = &spi_2;
 	};
 
+	bus_disp1: bus-disp1 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK400_DISP1>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_disp1_fimd: bus-disp1-fimd {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK300_DISP1>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_fsys: bus-fsys {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK200_FSYS>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_fsys2: bus-fsys2 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK200_FSYS2>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_fsys_apb: bus-fsys-apb {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_PCLK200_FSYS>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_g2d: bus-g2d {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK333_G2D>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_g2d_acp: bus-g2d-acp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK266_G2D>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+	bus_gen: bus-gen {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK266>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_gscl_scaler: bus-gscl-scaler {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK300_GSCL>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_jpeg: bus-jpeg {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK300_JPEG>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_jpeg_apb: bus-jpeg-apb {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK166>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_mfc: bus-mfc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK333>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_mscl: bus-mscl {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK400_MSCL>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_noc: bus-noc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK100_NOC>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_peri: bus-peri {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK66>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
+	bus_wcore: bus-wcore {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DOUT_ACLK400_WCORE>;
+		clock-names = "bus";
+		status = "disabled";
+	};
+
 	/*
 	 * The 'cpus' node is not present here but instead it is provided
 	 * by exynos5420-cpus.dtsi or exynos5422-cpus.dtsi.
 	 */
 
-	cluster_a15_opp_table: opp_table0 {
+	cluster_a15_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
 		opp-1800000000 {
 			opp-hz = /bits/ 64 <1800000000>;
-			opp-microvolt = <1250000>;
+			opp-microvolt = <1250000 1250000 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1700000000 {
 			opp-hz = /bits/ 64 <1700000000>;
-			opp-microvolt = <1212500>;
+			opp-microvolt = <1212500 1212500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1600000000 {
 			opp-hz = /bits/ 64 <1600000000>;
-			opp-microvolt = <1175000>;
+			opp-microvolt = <1175000 1175000 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1500000000 {
 			opp-hz = /bits/ 64 <1500000000>;
-			opp-microvolt = <1137500>;
+			opp-microvolt = <1137500 1137500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1400000000 {
 			opp-hz = /bits/ 64 <1400000000>;
-			opp-microvolt = <1112500>;
+			opp-microvolt = <1112500 1112500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1300000000 {
 			opp-hz = /bits/ 64 <1300000000>;
-			opp-microvolt = <1062500>;
+			opp-microvolt = <1062500 1062500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <1037500>;
+			opp-microvolt = <1037500 1037500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1100000000 {
 			opp-hz = /bits/ 64 <1100000000>;
-			opp-microvolt = <1012500>;
+			opp-microvolt = <1012500 1012500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = < 987500>;
+			opp-microvolt = < 987500 987500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-900000000 {
 			opp-hz = /bits/ 64 <900000000>;
-			opp-microvolt = < 962500>;
+			opp-microvolt = < 962500 962500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
-			opp-microvolt = < 937500>;
+			opp-microvolt = < 937500 937500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 		opp-700000000 {
 			opp-hz = /bits/ 64 <700000000>;
-			opp-microvolt = < 912500>;
+			opp-microvolt = < 912500 912500 1500000>;
 			clock-latency-ns = <140000>;
 		};
 	};
 
-	cluster_a7_opp_table: opp_table1 {
+	cluster_a7_opp_table: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -182,7 +290,7 @@
 
 		clock_audss: audss-clock-controller@3810000 {
 			compatible = "samsung,exynos5420-audss-clock";
-			reg = <0x03810000 0x0C>;
+			reg = <0x03810000 0x0c>;
 			#clock-cells = <1>;
 			clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MAU_EPLL>,
 				 <&clock CLK_SCLK_MAUDIO0>, <&clock CLK_SCLK_MAUPCM0>;
@@ -240,9 +348,6 @@
 		dmc: memory-controller@10c20000 {
 			compatible = "samsung,exynos5422-dmc";
 			reg = <0x10c20000 0x10000>, <0x10c30000 0x10000>;
-			interrupt-parent = <&combiner>;
-			interrupts = <16 0>, <16 1>;
-			interrupt-names = "drex_0", "drex_1";
 			clocks = <&clock CLK_FOUT_SPLL>,
 				 <&clock CLK_MOUT_SCLK_SPLL>,
 				 <&clock CLK_FF_DOUT_SPLL2>,
@@ -265,37 +370,37 @@
 
 		nocp_mem0_0: nocp@10ca1000 {
 			compatible = "samsung,exynos5420-nocp";
-			reg = <0x10CA1000 0x200>;
+			reg = <0x10ca1000 0x200>;
 			status = "disabled";
 		};
 
 		nocp_mem0_1: nocp@10ca1400 {
 			compatible = "samsung,exynos5420-nocp";
-			reg = <0x10CA1400 0x200>;
+			reg = <0x10ca1400 0x200>;
 			status = "disabled";
 		};
 
 		nocp_mem1_0: nocp@10ca1800 {
 			compatible = "samsung,exynos5420-nocp";
-			reg = <0x10CA1800 0x200>;
+			reg = <0x10ca1800 0x200>;
 			status = "disabled";
 		};
 
 		nocp_mem1_1: nocp@10ca1c00 {
 			compatible = "samsung,exynos5420-nocp";
-			reg = <0x10CA1C00 0x200>;
+			reg = <0x10ca1c00 0x200>;
 			status = "disabled";
 		};
 
 		nocp_g3d_0: nocp@11a51000 {
 			compatible = "samsung,exynos5420-nocp";
-			reg = <0x11A51000 0x200>;
+			reg = <0x11a51000 0x200>;
 			status = "disabled";
 		};
 
 		nocp_g3d_1: nocp@11a51400 {
 			compatible = "samsung,exynos5420-nocp";
-			reg = <0x11A51400 0x200>;
+			reg = <0x11a51400 0x200>;
 			status = "disabled";
 		};
 
@@ -305,8 +410,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX0_0>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc0_0: ppmu-event3-dmc0_0 {
-					event-name = "ppmu-event3-dmc0_0";
+				ppmu_event3_dmc0_0: ppmu-event3-dmc0-0 {
+					event-name = "ppmu-event3-dmc0-0";
 				};
 			};
 		};
@@ -317,8 +422,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX0_1>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc0_1: ppmu-event3-dmc0_1 {
-					event-name = "ppmu-event3-dmc0_1";
+				ppmu_event3_dmc0_1: ppmu-event3-dmc0-1 {
+					event-name = "ppmu-event3-dmc0-1";
 				};
 			};
 		};
@@ -329,8 +434,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX1_0>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc1_0: ppmu-event3-dmc1_0 {
-					event-name = "ppmu-event3-dmc1_0";
+				ppmu_event3_dmc1_0: ppmu-event3-dmc1-0 {
+					event-name = "ppmu-event3-dmc1-0";
 				};
 			};
 		};
@@ -341,8 +446,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX1_1>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc1_1: ppmu-event3-dmc1_1 {
-					event-name = "ppmu-event3-dmc1_1";
+				ppmu_event3_dmc1_1: ppmu-event3-dmc1-1 {
+					event-name = "ppmu-event3-dmc1-1";
 				};
 			};
 		};
@@ -377,14 +482,14 @@
 
 		disp_pd: power-domain@100440c0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x100440C0 0x20>;
+			reg = <0x100440c0 0x20>;
 			#power-domain-cells = <0>;
 			label = "DISP";
 		};
 
 		mau_pd: power-domain@100440e0 {
 			compatible = "samsung,exynos4210-pd";
-			reg = <0x100440E0 0x20>;
+			reg = <0x100440e0 0x20>;
 			#power-domain-cells = <0>;
 			label = "MAU";
 		};
@@ -433,76 +538,58 @@
 			power-domains = <&mau_pd>;
 		};
 
-		amba {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			interrupt-parent = <&gic>;
-			ranges;
-
-			adma: adma@3880000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x03880000 0x1000>;
-				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock_audss EXYNOS_ADMA>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <6>;
-				#dma-requests = <16>;
-				power-domains = <&mau_pd>;
-			};
-
-			pdma0: pdma@121a0000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x121A0000 0x1000>;
-				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
-
-			pdma1: pdma@121b0000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x121B0000 0x1000>;
-				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_PDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
-
-			mdma0: mdma@10800000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x10800000 0x1000>;
-				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_MDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <1>;
-			};
+		adma: dma-controller@3880000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x03880000 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock_audss EXYNOS_ADMA>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+			power-domains = <&mau_pd>;
+		};
 
-			mdma1: mdma@11c10000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0x11C10000 0x1000>;
-				interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clock CLK_MDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <1>;
-				/*
-				 * MDMA1 can support both secure and non-secure
-				 * AXI transactions. When this is enabled in
-				 * the kernel for boards that run in secure
-				 * mode, we are getting imprecise external
-				 * aborts causing the kernel to oops.
-				 */
-				status = "disabled";
-			};
+		pdma0: dma-controller@121a0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x121a0000 0x1000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
+
+		pdma1: dma-controller@121b0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x121b0000 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_PDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
+
+		mdma0: dma-controller@10800000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x10800000 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_MDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
+
+		mdma1: dma-controller@11c10000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x11c10000 0x1000>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock CLK_MDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+			/*
+			 * MDMA1 can support both secure and non-secure
+			 * AXI transactions. When this is enabled in
+			 * the kernel for boards that run in secure
+			 * mode, we are getting imprecise external
+			 * aborts causing the kernel to oops.
+			 */
+			status = "disabled";
 		};
 
 		i2s0: i2s@3830000 {
@@ -528,7 +615,7 @@
 
 		i2s1: i2s@12d60000 {
 			compatible = "samsung,exynos5420-i2s";
-			reg = <0x12D60000 0x100>;
+			reg = <0x12d60000 0x100>;
 			dmas = <&pdma1 12>,
 				<&pdma1 11>;
 			dma-names = "tx", "rx";
@@ -544,7 +631,7 @@
 
 		i2s2: i2s@12d70000 {
 			compatible = "samsung,exynos5420-i2s";
-			reg = <0x12D70000 0x100>;
+			reg = <0x12d70000 0x100>;
 			dmas = <&pdma0 12>,
 				<&pdma0 11>;
 			dma-names = "tx", "rx";
@@ -606,19 +693,7 @@
 			status = "disabled";
 		};
 
-		dp_phy: dp-video-phy {
-			compatible = "samsung,exynos5420-dp-video-phy";
-			samsung,pmu-syscon = <&pmu_system_controller>;
-			#phy-cells = <0>;
-		};
-
-		mipi_phy: mipi-video-phy {
-			compatible = "samsung,s5pv210-mipi-video-phy";
-			syscon = <&pmu_system_controller>;
-			#phy-cells = <1>;
-		};
-
-		dsi@14500000 {
+		dsi: dsi@14500000 {
 			compatible = "samsung,exynos5410-mipi-dsi";
 			reg = <0x14500000 0x10000>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -633,7 +708,7 @@
 
 		hsi2c_8: i2c@12e00000 {
 			compatible = "samsung,exynos5250-hsi2c";
-			reg = <0x12E00000 0x1000>;
+			reg = <0x12e00000 0x1000>;
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -646,7 +721,7 @@
 
 		hsi2c_9: i2c@12e10000 {
 			compatible = "samsung,exynos5250-hsi2c";
-			reg = <0x12E10000 0x1000>;
+			reg = <0x12e10000 0x1000>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -659,7 +734,7 @@
 
 		hsi2c_10: i2c@12e20000 {
 			compatible = "samsung,exynos5250-hsi2c";
-			reg = <0x12E20000 0x1000>;
+			reg = <0x12e20000 0x1000>;
 			interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -686,13 +761,13 @@
 			#sound-dai-cells = <0>;
 		};
 
-		hdmiphy: hdmiphy@145d0000 {
-			reg = <0x145D0000 0x20>;
+		hdmiphy: hdmi-phy@145d0000 {
+			reg = <0x145d0000 0x20>;
 		};
 
 		hdmicec: cec@101b0000 {
 			compatible = "samsung,s5p-cec";
-			reg = <0x101B0000 0x200>;
+			reg = <0x101b0000 0x200>;
 			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_HDMI_CEC>;
 			clock-names = "hdmicec";
@@ -717,7 +792,7 @@
 
 		rotator: rotator@11c00000 {
 			compatible = "samsung,exynos5250-rotator";
-			reg = <0x11C00000 0x64>;
+			reg = <0x11c00000 0x64>;
 			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_ROTATOR>;
 			clock-names = "rotator";
@@ -744,6 +819,56 @@
 			iommus = <&sysmmu_gscl1>;
 		};
 
+		gpu: gpu@11800000 {
+			compatible = "samsung,exynos5420-mali", "arm,mali-t628";
+			reg = <0x11800000 0x5000>;
+			interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "job", "mmu", "gpu";
+
+			clocks = <&clock CLK_G3D>;
+			clock-names = "core";
+			power-domains = <&g3d_pd>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			status = "disabled";
+			#cooling-cells = <2>;
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-177000000 {
+					opp-hz = /bits/ 64 <177000000>;
+					opp-microvolt = <812500>;
+				};
+				opp-266000000 {
+					opp-hz = /bits/ 64 <266000000>;
+					opp-microvolt = <862500>;
+				};
+				opp-350000000 {
+					opp-hz = /bits/ 64 <350000000>;
+					opp-microvolt = <912500>;
+				};
+				opp-420000000 {
+					opp-hz = /bits/ 64 <420000000>;
+					opp-microvolt = <962500>;
+				};
+				opp-480000000 {
+					opp-hz = /bits/ 64 <480000000>;
+					opp-microvolt = <1000000>;
+				};
+				opp-543000000 {
+					opp-hz = /bits/ 64 <543000000>;
+					opp-microvolt = <1037500>;
+				};
+				opp-600000000 {
+					opp-hz = /bits/ 64 <600000000>;
+					opp-microvolt = <1150000>;
+				};
+			};
+		};
+
 		scaler_0: scaler@12800000 {
 			compatible = "samsung,exynos5420-scaler";
 			reg = <0x12800000 0x1294>;
@@ -776,7 +901,7 @@
 
 		jpeg_0: jpeg@11f50000 {
 			compatible = "samsung,exynos5420-jpeg";
-			reg = <0x11F50000 0x1000>;
+			reg = <0x11f50000 0x1000>;
 			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "jpeg";
 			clocks = <&clock CLK_JPEG>;
@@ -785,7 +910,7 @@
 
 		jpeg_1: jpeg@11f60000 {
 			compatible = "samsung,exynos5420-jpeg";
-			reg = <0x11F60000 0x1000>;
+			reg = <0x11f60000 0x1000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "jpeg";
 			clocks = <&clock CLK_JPEG2>;
@@ -793,7 +918,7 @@
 		};
 
 		pmu_system_controller: system-controller@10040000 {
-			compatible = "samsung,exynos5420-pmu", "syscon";
+			compatible = "samsung,exynos5420-pmu", "simple-mfd", "syscon";
 			reg = <0x10040000 0x5000>;
 			clock-names = "clkout16";
 			clocks = <&clock CLK_FIN_PLL>;
@@ -801,6 +926,16 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			interrupt-parent = <&gic>;
+
+			dp_phy: dp-phy {
+				compatible = "samsung,exynos5420-dp-video-phy";
+				#phy-cells = <0>;
+			};
+
+			mipi_phy: mipi-phy {
+				compatible = "samsung,exynos5420-mipi-video-phy";
+				#phy-cells = <1>;
+			};
 		};
 
 		tmu_cpu0: tmu@10060000 {
@@ -850,7 +985,7 @@
 
 		sysmmu_g2dr: sysmmu@10a60000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x10A60000 0x1000>;
+			reg = <0x10a60000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <24 5>;
 			clock-names = "sysmmu", "master";
@@ -860,7 +995,7 @@
 
 		sysmmu_g2dw: sysmmu@10a70000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x10A70000 0x1000>;
+			reg = <0x10a70000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <22 2>;
 			clock-names = "sysmmu", "master";
@@ -881,7 +1016,7 @@
 
 		sysmmu_gscl0: sysmmu@13e80000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13E80000 0x1000>;
+			reg = <0x13e80000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <2 0>;
 			clock-names = "sysmmu", "master";
@@ -892,7 +1027,7 @@
 
 		sysmmu_gscl1: sysmmu@13e90000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x13E90000 0x1000>;
+			reg = <0x13e90000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <2 2>;
 			clock-names = "sysmmu", "master";
@@ -924,7 +1059,7 @@
 
 		sysmmu_scaler2r: sysmmu@128a0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x128A0000 0x1000>;
+			reg = <0x128a0000 0x1000>;
 			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "sysmmu", "master";
 			clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
@@ -934,7 +1069,7 @@
 
 		sysmmu_scaler0w: sysmmu@128c0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x128C0000 0x1000>;
+			reg = <0x128c0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <27 2>;
 			clock-names = "sysmmu", "master";
@@ -945,7 +1080,7 @@
 
 		sysmmu_scaler1w: sysmmu@128d0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x128D0000 0x1000>;
+			reg = <0x128d0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <22 6>;
 			clock-names = "sysmmu", "master";
@@ -956,7 +1091,7 @@
 
 		sysmmu_scaler2w: sysmmu@128e0000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x128E0000 0x1000>;
+			reg = <0x128e0000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <19 6>;
 			clock-names = "sysmmu", "master";
@@ -967,7 +1102,7 @@
 
 		sysmmu_rotator: sysmmu@11d40000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11D40000 0x1000>;
+			reg = <0x11d40000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 0>;
 			clock-names = "sysmmu", "master";
@@ -977,7 +1112,7 @@
 
 		sysmmu_jpeg0: sysmmu@11f10000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11F10000 0x1000>;
+			reg = <0x11f10000 0x1000>;
 			interrupt-parent = <&combiner>;
 			interrupts = <4 2>;
 			clock-names = "sysmmu", "master";
@@ -987,7 +1122,7 @@
 
 		sysmmu_jpeg1: sysmmu@11f20000 {
 			compatible = "samsung,exynos-sysmmu";
-			reg = <0x11F20000 0x1000>;
+			reg = <0x11f20000 0x1000>;
 			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "sysmmu", "master";
 			clocks = <&clock CLK_SMMU_JPEG2>, <&clock CLK_JPEG2>;
@@ -1037,377 +1172,6 @@
 			power-domains = <&disp_pd>;
 			#iommu-cells = <0>;
 		};
-
-		bus_wcore: bus_wcore {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK400_WCORE>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_wcore_opp_table>;
-			status = "disabled";
-		};
-
-		bus_noc: bus_noc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK100_NOC>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_noc_opp_table>;
-			status = "disabled";
-		};
-
-		bus_fsys_apb: bus_fsys_apb {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_PCLK200_FSYS>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_fsys_apb_opp_table>;
-			status = "disabled";
-		};
-
-		bus_fsys: bus_fsys {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK200_FSYS>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_fsys_apb_opp_table>;
-			status = "disabled";
-		};
-
-		bus_fsys2: bus_fsys2 {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK200_FSYS2>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_fsys2_opp_table>;
-			status = "disabled";
-		};
-
-		bus_mfc: bus_mfc {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK333>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_mfc_opp_table>;
-			status = "disabled";
-		};
-
-		bus_gen: bus_gen {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK266>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_gen_opp_table>;
-			status = "disabled";
-		};
-
-		bus_peri: bus_peri {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK66>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_peri_opp_table>;
-			status = "disabled";
-		};
-
-		bus_g2d: bus_g2d {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK333_G2D>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_g2d_opp_table>;
-			status = "disabled";
-		};
-
-		bus_g2d_acp: bus_g2d_acp {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK266_G2D>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_g2d_acp_opp_table>;
-			status = "disabled";
-		};
-
-		bus_jpeg: bus_jpeg {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK300_JPEG>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_jpeg_opp_table>;
-			status = "disabled";
-		};
-
-		bus_jpeg_apb: bus_jpeg_apb {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK166>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_jpeg_apb_opp_table>;
-			status = "disabled";
-		};
-
-		bus_disp1_fimd: bus_disp1_fimd {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK300_DISP1>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_disp1_fimd_opp_table>;
-			status = "disabled";
-		};
-
-		bus_disp1: bus_disp1 {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK400_DISP1>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_disp1_opp_table>;
-			status = "disabled";
-		};
-
-		bus_gscl_scaler: bus_gscl_scaler {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK300_GSCL>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_gscl_opp_table>;
-			status = "disabled";
-		};
-
-		bus_mscl: bus_mscl {
-			compatible = "samsung,exynos-bus";
-			clocks = <&clock CLK_DOUT_ACLK400_MSCL>;
-			clock-names = "bus";
-			operating-points-v2 = <&bus_mscl_opp_table>;
-			status = "disabled";
-		};
-
-		bus_wcore_opp_table: opp_table2 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <84000000>;
-				opp-microvolt = <925000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <111000000>;
-				opp-microvolt = <950000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <222000000>;
-				opp-microvolt = <950000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <333000000>;
-				opp-microvolt = <950000>;
-			};
-			opp04 {
-				opp-hz = /bits/ 64 <400000000>;
-				opp-microvolt = <987500>;
-			};
-		};
-
-		bus_noc_opp_table: opp_table3 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <67000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <75000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <86000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-		};
-
-		bus_fsys_apb_opp_table: opp_table4 {
-			compatible = "operating-points-v2";
-			opp-shared;
-
-			opp00 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-		};
-
-		bus_fsys2_opp_table: opp_table5 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <75000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <100000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <150000000>;
-			};
-		};
-
-		bus_mfc_opp_table: opp_table6 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <96000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <111000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <167000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <222000000>;
-			};
-			opp04 {
-				opp-hz = /bits/ 64 <333000000>;
-			};
-		};
-
-		bus_gen_opp_table: opp_table7 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <89000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <133000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <178000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <267000000>;
-			};
-		};
-
-		bus_peri_opp_table: opp_table8 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <67000000>;
-			};
-		};
-
-		bus_g2d_opp_table: opp_table9 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <84000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <167000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <222000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <300000000>;
-			};
-			opp04 {
-				opp-hz = /bits/ 64 <333000000>;
-			};
-		};
-
-		bus_g2d_acp_opp_table: opp_table10 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <67000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <133000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <178000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <267000000>;
-			};
-		};
-
-		bus_jpeg_opp_table: opp_table11 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <75000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <150000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <300000000>;
-			};
-		};
-
-		bus_jpeg_apb_opp_table: opp_table12 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <84000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <111000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <134000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <167000000>;
-			};
-		};
-
-		bus_disp1_fimd_opp_table: opp_table13 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <120000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-		};
-
-		bus_disp1_opp_table: opp_table14 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <120000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <300000000>;
-			};
-		};
-
-		bus_gscl_opp_table: opp_table15 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <150000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <200000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <300000000>;
-			};
-		};
-
-		bus_mscl_opp_table: opp_table16 {
-			compatible = "operating-points-v2";
-
-			opp00 {
-				opp-hz = /bits/ 64 <84000000>;
-			};
-			opp01 {
-				opp-hz = /bits/ 64 <167000000>;
-			};
-			opp02 {
-				opp-hz = /bits/ 64 <222000000>;
-			};
-			opp03 {
-				opp-hz = /bits/ 64 <333000000>;
-			};
-			opp04 {
-				opp-hz = /bits/ 64 <400000000>;
-			};
-		};
 	};
 
 	thermal-zones {
@@ -1416,20 +1180,20 @@
 			#include "exynos5420-trip-points.dtsi"
 		};
 		cpu1_thermal: cpu1-thermal {
-		       thermal-sensors = <&tmu_cpu1>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_cpu1>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 		cpu2_thermal: cpu2-thermal {
-		       thermal-sensors = <&tmu_cpu2>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_cpu2>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 		cpu3_thermal: cpu3-thermal {
-		       thermal-sensors = <&tmu_cpu3>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_cpu3>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 		gpu_thermal: gpu-thermal {
-		       thermal-sensors = <&tmu_gpu>;
-		       #include "exynos5420-trip-points.dtsi"
+			thermal-sensors = <&tmu_gpu>;
+			#include "exynos5420-trip-points.dtsi"
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/exynos5422-cpus.dtsi b/arch/arm/boot/dts/samsung/exynos5422-cpus.dtsi
index e4a5857c135f..412a0bb4b988 100644
--- a/arch/arm/boot/dts/exynos5422-cpus.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5422-cpus.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5422 SoC cpu device tree source
+ * Samsung Exynos5422 SoC cpu device tree source
  *
  * Copyright (c) 2015 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -21,6 +21,38 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
 		cpu0: cpu@100 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
@@ -31,6 +63,7 @@
 			operating-points-v2 = <&cluster_a7_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <539>;
+			dynamic-power-coefficient = <90>;
 		};
 
 		cpu1: cpu@101 {
@@ -43,6 +76,7 @@
 			operating-points-v2 = <&cluster_a7_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <539>;
+			dynamic-power-coefficient = <90>;
 		};
 
 		cpu2: cpu@102 {
@@ -55,6 +89,7 @@
 			operating-points-v2 = <&cluster_a7_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <539>;
+			dynamic-power-coefficient = <90>;
 		};
 
 		cpu3: cpu@103 {
@@ -67,6 +102,7 @@
 			operating-points-v2 = <&cluster_a7_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <539>;
+			dynamic-power-coefficient = <90>;
 		};
 
 		cpu4: cpu@0 {
@@ -79,6 +115,7 @@
 			operating-points-v2 = <&cluster_a15_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <310>;
 		};
 
 		cpu5: cpu@1 {
@@ -91,6 +128,7 @@
 			operating-points-v2 = <&cluster_a15_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <310>;
 		};
 
 		cpu6: cpu@2 {
@@ -103,6 +141,7 @@
 			operating-points-v2 = <&cluster_a15_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <310>;
 		};
 
 		cpu7: cpu@3 {
@@ -115,6 +154,7 @@
 			operating-points-v2 = <&cluster_a15_opp_table>;
 			#cooling-cells = <2>; /* min followed by max */
 			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <310>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/samsung/exynos5422-odroid-core.dtsi
index 059fa32d1a8f..2f5b8602e020 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroid-core.dtsi
@@ -16,7 +16,11 @@
 / {
 	memory@40000000 {
 		device_type = "memory";
-		reg = <0x40000000 0x7EA00000>;
+		reg = <0x40000000 0x7ea00000>;
+	};
+
+	aliases {
+		mmc2 = &mmc_2;
 	};
 
 	chosen {
@@ -35,7 +39,264 @@
 		};
 	};
 
-	dmc_opp_table: opp_table2 {
+	bus_wcore_opp_table: opp-table-2 {
+		compatible = "operating-points-v2";
+
+		/* derived from 532MHz MPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <88700000>;
+			opp-microvolt = <925000 925000 1400000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <950000 950000 1400000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <177400000>;
+			opp-microvolt = <950000 950000 1400000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <266000000>;
+			opp-microvolt = <950000 950000 1400000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <532000000>;
+			opp-microvolt = <1000000 1000000 1400000>;
+		};
+	};
+
+	bus_noc_opp_table: opp-table-3 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <66600000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <74000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <83250000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <111000000>;
+		};
+	};
+
+	bus_fsys_apb_opp_table: opp-table-4 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <111000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <222000000>;
+		};
+	};
+
+	bus_fsys2_opp_table: opp-table-5 {
+		compatible = "operating-points-v2";
+
+		/* derived from 600MHz DPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <75000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <120000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+	};
+
+	bus_mfc_opp_table: opp-table-6 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <83250000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <111000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <166500000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <222000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <333000000>;
+		};
+	};
+
+	bus_gen_opp_table: opp-table-7 {
+		compatible = "operating-points-v2";
+
+		/* derived from 532MHz MPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <88700000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <178000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <266000000>;
+		};
+	};
+
+	bus_peri_opp_table: opp-table-8 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <66600000>;
+		};
+	};
+
+	bus_g2d_opp_table: opp-table-9 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <83250000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <111000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <166500000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <222000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <333000000>;
+		};
+	};
+
+	bus_g2d_acp_opp_table: opp-table-10 {
+		compatible = "operating-points-v2";
+
+		/* derived from 532MHz MPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <66500000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <178000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <266000000>;
+		};
+	};
+
+	bus_jpeg_opp_table: opp-table-11 {
+		compatible = "operating-points-v2";
+
+		/* derived from 600MHz DPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <75000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <150000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <300000000>;
+		};
+	};
+
+	bus_jpeg_apb_opp_table: opp-table-12 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <83250000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <111000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <133000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <166500000>;
+		};
+	};
+
+	bus_disp1_fimd_opp_table: opp-table-13 {
+		compatible = "operating-points-v2";
+
+		/* derived from 600MHz DPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <120000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+	};
+
+	bus_disp1_opp_table: opp-table-14 {
+		compatible = "operating-points-v2";
+
+		/* derived from 600MHz DPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <120000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <300000000>;
+		};
+	};
+
+	bus_gscl_opp_table: opp-table-15 {
+		compatible = "operating-points-v2";
+
+		/* derived from 600MHz DPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <150000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <300000000>;
+		};
+	};
+
+	bus_mscl_opp_table: opp-table-16 {
+		compatible = "operating-points-v2";
+
+		/* derived from 666MHz CPLL */
+		opp00 {
+			opp-hz = /bits/ 64 <84000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <167000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <222000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <333000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <666000000>;
+		};
+	};
+
+	dmc_opp_table: opp-table-17 {
 		compatible = "operating-points-v2";
 
 		opp00 {
@@ -76,8 +337,6 @@
 		compatible	= "samsung,K3QF2F20DB", "jedec,lpddr3";
 		density		= <16384>;
 		io-width	= <32>;
-		#address-cells  = <1>;
-		#size-cells     = <0>;
 
 		tRFC-min-tck		= <17>;
 		tRRD-min-tck		= <2>;
@@ -101,10 +360,9 @@
 		tCKESR-min-tck		= <2>;
 		tMRD-min-tck		= <5>;
 
-		timings_samsung_K3QF2F20DB_800mhz: lpddr3-timings@800000000 {
+		timings_samsung_K3QF2F20DB_800mhz: timings {
 			compatible	= "jedec,lpddr3-timings";
-			/* workaround: 'reg' shows max-freq */
-			reg		= <800000000>;
+			max-freq	= <800000000>;
 			min-freq	= <100000000>;
 			tRFC		= <65000>;
 			tRRD		= <6000>;
@@ -134,6 +392,7 @@
 };
 
 &bus_wcore {
+	operating-points-v2 = <&bus_wcore_opp_table>;
 	devfreq-events = <&nocp_mem0_0>, <&nocp_mem0_1>,
 			<&nocp_mem1_0>, <&nocp_mem1_1>;
 	vdd-supply = <&buck3_reg>;
@@ -142,76 +401,85 @@
 };
 
 &bus_noc {
+	operating-points-v2 = <&bus_noc_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_fsys_apb {
-	devfreq = <&bus_wcore>;
-	status = "okay";
-};
-
-&bus_fsys {
+	operating-points-v2 = <&bus_fsys_apb_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_fsys2 {
+	operating-points-v2 = <&bus_fsys2_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_mfc {
+	operating-points-v2 = <&bus_mfc_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_gen {
+	operating-points-v2 = <&bus_gen_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_peri {
+	operating-points-v2 = <&bus_peri_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_g2d {
+	operating-points-v2 = <&bus_g2d_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_g2d_acp {
+	operating-points-v2 = <&bus_g2d_acp_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_jpeg {
+	operating-points-v2 = <&bus_jpeg_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_jpeg_apb {
+	operating-points-v2 = <&bus_jpeg_apb_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_disp1_fimd {
+	operating-points-v2 = <&bus_disp1_fimd_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_disp1 {
+	operating-points-v2 = <&bus_disp1_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_gscl_scaler {
+	operating-points-v2 = <&bus_gscl_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
 
 &bus_mscl {
+	operating-points-v2 = <&bus_mscl_opp_table>;
 	devfreq = <&bus_wcore>;
 	status = "okay";
 };
@@ -236,15 +504,16 @@
 &hsi2c_4 {
 	status = "okay";
 
-	s2mps11_pmic@66 {
+	pmic@66 {
 		compatible = "samsung,s2mps11-pmic";
 		reg = <0x66>;
 		samsung,s2mps11-acokb-ground;
 
 		interrupt-parent = <&gpx0>;
-		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s2mps11_irq>;
+		wakeup-source;
 
 		s2mps11_osc: clocks {
 			compatible = "samsung,s2mps11-clk";
@@ -601,6 +870,8 @@
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 				regulator-boot-on;
+				regulator-coupled-with = <&buck3_reg>;
+				regulator-coupled-max-spread = <300000>;
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -613,6 +884,8 @@
 				regulator-max-microvolt = <1400000>;
 				regulator-always-on;
 				regulator-boot-on;
+				regulator-coupled-with = <&buck2_reg>;
+				regulator-coupled-max-spread = <300000>;
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -623,8 +896,8 @@
 				regulator-name = "vdd_g3d";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1400000>;
-				regulator-always-on;
 				regulator-boot-on;
+				regulator-always-on;
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -727,7 +1000,7 @@
 };
 
 &pinctrl_0 {
-	s2mps11_irq: s2mps11-irq {
+	s2mps11_irq: s2mps11-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -771,6 +1044,11 @@
 	vtmu-supply = <&ldo7_reg>;
 };
 
+&gpu {
+	mali-supply = <&buck4_reg>;
+	status = "okay";
+};
+
 &rtc {
 	status = "okay";
 	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidhc1.dts b/arch/arm/boot/dts/samsung/exynos5422-odroidhc1.dts
index d271e7548826..5e4280393706 100644
--- a/arch/arm/boot/dts/exynos5422-odroidhc1.dts
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroidhc1.dts
@@ -8,6 +8,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos5422-odroid-core.dtsi"
 
 / {
@@ -15,21 +16,22 @@
 	compatible = "hardkernel,odroid-hc1", "samsung,exynos5800", \
 		     "samsung,exynos5";
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		blueled {
-			label = "blue:heartbeat";
+		led-1 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			pwms = <&pwm 2 2000000 0>;
 			pwm-names = "pwm2";
-			max_brightness = <255>;
+			max-brightness = <255>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
 	thermal-zones {
 		cpu0_thermal: cpu0-thermal {
-			thermal-sensors = <&tmu_cpu0 0>;
+			thermal-sensors = <&tmu_cpu0>;
 			trips {
 				cpu0_alert0: cpu-alert-0 {
 					temperature = <70000>; /* millicelsius */
@@ -72,19 +74,19 @@
 				 */
 				map1 {
 					trip = <&cpu0_alert1>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
 				};
 			};
 		};
 		cpu1_thermal: cpu1-thermal {
-			thermal-sensors = <&tmu_cpu1 0>;
+			thermal-sensors = <&tmu_cpu1>;
 			trips {
 				cpu1_alert0: cpu-alert-0 {
 					temperature = <70000>;
@@ -116,19 +118,19 @@
 				};
 				map1 {
 					trip = <&cpu1_alert1>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
 				};
 			};
 		};
 		cpu2_thermal: cpu2-thermal {
-			thermal-sensors = <&tmu_cpu2 0>;
+			thermal-sensors = <&tmu_cpu2>;
 			trips {
 				cpu2_alert0: cpu-alert-0 {
 					temperature = <70000>;
@@ -160,19 +162,19 @@
 				};
 				map1 {
 					trip = <&cpu2_alert1>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
 				};
 			};
 		};
 		cpu3_thermal: cpu3-thermal {
-			thermal-sensors = <&tmu_cpu3 0>;
+			thermal-sensors = <&tmu_cpu3>;
 			trips {
 				cpu3_alert0: cpu-alert-0 {
 					temperature = <70000>;
@@ -204,14 +206,44 @@
 				};
 				map1 {
 					trip = <&cpu3_alert1>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
+				};
+			};
+		};
+		gpu_thermal: gpu-thermal {
+			thermal-sensors = <&tmu_gpu>;
+			trips {
+				gpu_alert0: gpu-alert-0 {
+					temperature = <70000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+				gpu_alert1: gpu-alert-1 {
+					temperature = <85000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+				gpu_crit0: gpu-crit-0 {
+					temperature = <120000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&gpu_alert0>;
+					cooling-device = <&gpu 0 2>;
+				};
+				map1 {
+					trip = <&gpu_alert1>;
+					cooling-device = <&gpu 3 6>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-audio.dtsi
new file mode 100644
index 000000000000..52a1d8fd5452
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-audio.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Hardkernel Odroid XU3 audio subsystem device tree source
+ *
+ * Copyright (c) 2015 Krzysztof Kozlowski
+ * Copyright (c) 2014 Collabora Ltd.
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+#include <dt-bindings/sound/samsung-i2s.h>
+
+/ {
+	sound: sound {
+		compatible = "samsung,odroid-xu3-audio";
+		model = "Odroid-XU3";
+
+		samsung,audio-widgets =
+			"Headphone", "Headphone Jack",
+			"Speakers", "Speakers";
+		audio-routing = "Headphone Jack", "HPL",
+				"Headphone Jack", "HPR",
+				"Headphone Jack", "MICBIAS",
+				"IN12", "Headphone Jack",
+				"Speakers", "SPKL",
+				"Speakers", "SPKR",
+				"I2S Playback", "Mixer DAI TX",
+				"HiFi Playback", "Mixer DAI TX",
+				"Mixer DAI RX", "HiFi Capture";
+
+		cpu {
+			sound-dai = <&i2s0 0>, <&i2s0 1>;
+		};
+		codec {
+			sound-dai = <&hdmi>, <&max98090>;
+		};
+	};
+};
+
+&hsi2c_5 {
+	status = "okay";
+	max98090: audio-codec@10 {
+		compatible = "maxim,max98090";
+		reg = <0x10>;
+		interrupt-parent = <&gpx3>;
+		interrupts = <2 IRQ_TYPE_NONE>;
+		clocks = <&i2s0 CLK_I2S_CDCLK>;
+		clock-names = "mclk";
+		#sound-dai-cells = <0>;
+	};
+};
+
+&i2s0 {
+	status = "okay";
+	assigned-clocks = <&clock CLK_MOUT_EPLL>,
+			<&clock CLK_MOUT_MAU_EPLL>,
+			<&clock CLK_MOUT_USER_MAU_EPLL>,
+			<&clock_audss EXYNOS_MOUT_AUDSS>,
+			<&clock_audss EXYNOS_MOUT_I2S>,
+			<&i2s0 CLK_I2S_RCLK_SRC>,
+			<&clock_audss EXYNOS_DOUT_SRP>,
+			<&clock_audss EXYNOS_DOUT_AUD_BUS>,
+			<&clock_audss EXYNOS_DOUT_I2S>;
+
+	assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
+			<&clock CLK_MOUT_EPLL>,
+			<&clock CLK_MOUT_MAU_EPLL>,
+			<&clock CLK_MAU_EPLL>,
+			<&clock_audss EXYNOS_MOUT_AUDSS>,
+			<&clock_audss EXYNOS_SCLK_I2S>;
+
+	assigned-clock-rates = <0>,
+			<0>,
+			<0>,
+			<0>,
+			<0>,
+			<0>,
+			<196608001>,
+			<(196608002 / 2)>,
+			<196608000>;
+
+};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-common.dtsi
index 838872037493..b4a851aa8881 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-common.dtsi
@@ -13,12 +13,16 @@
 #include "exynos5422-odroid-core.dtsi"
 
 / {
-	gpio_keys {
+	aliases {
+		mmc0 = &mmc_0;
+	};
+
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key>;
 
-		power_key {
+		power-key {
 			/*
 			 * The power button (SW2) is connected to the PWRON
 			 * pin (active high) of the S2MPS11 PMIC, which acts
@@ -50,7 +54,7 @@
 
 	thermal-zones {
 		cpu0_thermal: cpu0-thermal {
-			thermal-sensors = <&tmu_cpu0 0>;
+			thermal-sensors = <&tmu_cpu0>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -107,7 +111,7 @@
 				/*
 				 * When reaching cpu0_alert3, reduce CPU
 				 * by 2 steps. On Exynos5422/5800 that would
-				 * be: 1600 MHz and 1100 MHz.
+				 * (usually) be: 1800 MHz and 1200 MHz.
 				 */
 				map3 {
 					trip = <&cpu0_alert3>;
@@ -122,24 +126,24 @@
 				};
 				/*
 				 * When reaching cpu0_alert4, reduce CPU
-				 * further, down to 600 MHz (12 steps for big,
-				 * 7 steps for LITTLE).
+				 * further, down to 600 MHz (14 steps for big,
+				 * 8 steps for LITTLE).
 				 */
-				map4 {
+				cpu0_cooling_map4: map4 {
 					trip = <&cpu0_alert4>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
 				};
 			};
 		};
 		cpu1_thermal: cpu1-thermal {
-			thermal-sensors = <&tmu_cpu1 0>;
+			thermal-sensors = <&tmu_cpu1>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -198,21 +202,21 @@
 							 <&cpu6 0 2>,
 							 <&cpu7 0 2>;
 				};
-				map4 {
+				cpu1_cooling_map4: map4 {
 					trip = <&cpu1_alert4>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
 				};
 			};
 		};
 		cpu2_thermal: cpu2-thermal {
-			thermal-sensors = <&tmu_cpu2 0>;
+			thermal-sensors = <&tmu_cpu2>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -271,21 +275,21 @@
 							 <&cpu6 0 2>,
 							 <&cpu7 0 2>;
 				};
-				map4 {
+				cpu2_cooling_map4: map4 {
 					trip = <&cpu2_alert4>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
 				};
 			};
 		};
 		cpu3_thermal: cpu3-thermal {
-			thermal-sensors = <&tmu_cpu3 0>;
+			thermal-sensors = <&tmu_cpu3>;
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
 			trips {
@@ -344,16 +348,75 @@
 							 <&cpu6 0 2>,
 							 <&cpu7 0 2>;
 				};
-				map4 {
+				cpu3_cooling_map4: map4 {
 					trip = <&cpu3_alert4>;
-					cooling-device = <&cpu0 3 7>,
-							 <&cpu1 3 7>,
-							 <&cpu2 3 7>,
-							 <&cpu3 3 7>,
-							 <&cpu4 3 12>,
-							 <&cpu5 3 12>,
-							 <&cpu6 3 12>,
-							 <&cpu7 3 12>;
+					cooling-device = <&cpu0 3 8>,
+							 <&cpu1 3 8>,
+							 <&cpu2 3 8>,
+							 <&cpu3 3 8>,
+							 <&cpu4 3 14>,
+							 <&cpu5 3 14>,
+							 <&cpu6 3 14>,
+							 <&cpu7 3 14>;
+				};
+			};
+		};
+		gpu_thermal: gpu-thermal {
+			thermal-sensors = <&tmu_gpu>;
+			polling-delay-passive = <250>;
+			polling-delay = <0>;
+			trips {
+				gpu_alert0: gpu-alert-0 {
+					temperature = <50000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				gpu_alert1: gpu-alert-1 {
+					temperature = <60000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				gpu_alert2: gpu-alert-2 {
+					temperature = <70000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				gpu_crit0: gpu-crit-0 {
+					temperature = <120000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+				gpu_alert3: gpu-alert-3 {
+					temperature = <70000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+				gpu_alert4: gpu-alert-4 {
+					temperature = <85000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&gpu_alert0>;
+					cooling-device = <&fan0 0 1>;
+				};
+				map1 {
+					trip = <&gpu_alert1>;
+					cooling-device = <&fan0 1 2>;
+				};
+				map2 {
+					trip = <&gpu_alert2>;
+					cooling-device = <&fan0 2 3>;
+				};
+				map3 {
+					trip = <&gpu_alert3>;
+					cooling-device = <&gpu 0 2>;
+				};
+				map4 {
+					trip = <&gpu_alert4>;
+					cooling-device = <&gpu 3 6>;
 				};
 			};
 		};
@@ -413,6 +476,7 @@
 	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	mmc-hs400-1_8v;
 	max-frequency = <200000000>;
@@ -421,14 +485,14 @@
 };
 
 &pinctrl_0 {
-	power_key: power-key {
+	power_key: power-key-pins {
 		samsung,pins = "gpx0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -437,7 +501,7 @@
 };
 
 &pinctrl_1 {
-	emmc_nrst_pin: emmc-nrst {
+	emmc_nrst_pin: emmc-nrst-pins {
 		samsung,pins = "gpd1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-lite.dts
new file mode 100644
index 000000000000..e3154a1cae23
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3-lite.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Hardkernel Odroid XU3-Lite board device tree source
+ *
+ * Copyright (c) 2015 Krzysztof Kozlowski
+ * Copyright (c) 2014 Collabora Ltd.
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos5422-odroidxu3-common.dtsi"
+#include "exynos5422-odroidxu3-audio.dtsi"
+#include "exynos54xx-odroidxu-leds.dtsi"
+
+/ {
+	model = "Hardkernel Odroid XU3 Lite";
+	compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5";
+
+	aliases {
+		ethernet = &ethernet;
+	};
+};
+
+&arm_a7_pmu {
+	status = "disabled";
+};
+
+&arm_a15_pmu {
+	status = "disabled";
+};
+
+&chipid {
+	samsung,asv-bin = <2>;
+};
+
+/*
+ * Odroid XU3-Lite board uses SoC revision with lower maximum frequencies
+ * than Odroid XU3/XU4 boards: 1.8 GHz for A15 cores & 1.3 GHz for A7 cores.
+ * Therefore we need to update OPPs tables and thermal maps accordingly.
+ */
+&cluster_a15_opp_table {
+	/delete-node/opp-2000000000;
+	/delete-node/opp-1900000000;
+};
+
+&cluster_a7_opp_table {
+	/delete-node/opp-1400000000;
+};
+
+&cpu0_cooling_map4 {
+	cooling-device = <&cpu0 3 7>,
+			 <&cpu1 3 7>,
+			 <&cpu2 3 7>,
+			 <&cpu3 3 7>,
+			 <&cpu4 3 12>,
+			 <&cpu5 3 12>,
+			 <&cpu6 3 12>,
+			 <&cpu7 3 12>;
+};
+
+&cpu1_cooling_map4 {
+	cooling-device = <&cpu0 3 7>,
+			 <&cpu1 3 7>,
+			 <&cpu2 3 7>,
+			 <&cpu3 3 7>,
+			 <&cpu4 3 12>,
+			 <&cpu5 3 12>,
+			 <&cpu6 3 12>,
+			 <&cpu7 3 12>;
+};
+
+&cpu2_cooling_map4 {
+	cooling-device = <&cpu0 3 7>,
+			 <&cpu1 3 7>,
+			 <&cpu2 3 7>,
+			 <&cpu3 3 7>,
+			 <&cpu4 3 12>,
+			 <&cpu5 3 12>,
+			 <&cpu6 3 12>,
+			 <&cpu7 3 12>;
+};
+
+&cpu3_cooling_map4 {
+	cooling-device = <&cpu0 3 7>,
+			 <&cpu1 3 7>,
+			 <&cpu2 3 7>,
+			 <&cpu3 3 7>,
+			 <&cpu4 3 12>,
+			 <&cpu5 3 12>,
+			 <&cpu6 3 12>,
+			 <&cpu7 3 12>;
+};
+
+&pwm {
+	/*
+	 * PWM 0 -- fan
+	 * PWM 1 -- Green LED
+	 * PWM 2 -- Blue LED
+	 * PWM 3 -- on MIPI connector for backlight
+	 */
+	pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	dr_mode = "peripheral";
+};
+
+&usbhost2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+			local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3.dts
index db0bc17a667b..a378d4937ff7 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroidxu3.dts
@@ -15,34 +15,38 @@
 / {
 	model = "Hardkernel Odroid XU3";
 	compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5";
+
+	aliases {
+		ethernet = &ethernet;
+	};
 };
 
 &i2c_0 {
 	status = "okay";
 
 	/* A15 cluster: VDD_ARM */
-	ina231@40 {
+	power-sensor@40 {
 		compatible = "ti,ina231";
 		reg = <0x40>;
 		shunt-resistor = <10000>;
 	};
 
 	/* memory: VDD_MEM */
-	ina231@41 {
+	power-sensor@41 {
 		compatible = "ti,ina231";
 		reg = <0x41>;
 		shunt-resistor = <10000>;
 	};
 
 	/* GPU: VDD_G3D */
-	ina231@44 {
+	power-sensor@44 {
 		compatible = "ti,ina231";
 		reg = <0x44>;
 		shunt-resistor = <10000>;
 	};
 
 	/* A7 cluster: VDD_KFC */
-	ina231@45 {
+	power-sensor@45 {
 		compatible = "ti,ina231";
 		reg = <0x45>;
 		shunt-resistor = <10000>;
@@ -70,3 +74,21 @@
 &usbdrd_dwc3_1 {
 	dr_mode = "peripheral";
 };
+
+&usbhost2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethernet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+			local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu4.dts b/arch/arm/boot/dts/samsung/exynos5422-odroidxu4.dts
index 892d389d6d09..363786f032cc 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu4.dts
+++ b/arch/arm/boot/dts/samsung/exynos5422-odroidxu4.dts
@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/sound/samsung-i2s.h>
 #include "exynos5422-odroidxu3-common.dtsi"
 
@@ -17,14 +18,15 @@
 	compatible = "hardkernel,odroid-xu4", "samsung,exynos5800", \
 		     "samsung,exynos5";
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		blueled {
-			label = "blue:heartbeat";
+		led-1 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			pwms = <&pwm 2 2000000 0>;
 			pwm-names = "pwm2";
-			max_brightness = <255>;
+			max-brightness = <255>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -33,31 +35,7 @@
 		compatible = "samsung,odroid-xu3-audio";
 		model = "Odroid-XU4";
 
-		samsung,audio-routing = "I2S Playback", "Mixer DAI TX";
-
-		assigned-clocks = <&clock CLK_MOUT_EPLL>,
-				<&clock CLK_MOUT_MAU_EPLL>,
-				<&clock CLK_MOUT_USER_MAU_EPLL>,
-				<&clock_audss EXYNOS_MOUT_AUDSS>,
-				<&clock_audss EXYNOS_MOUT_I2S>,
-				<&clock_audss EXYNOS_DOUT_SRP>,
-				<&clock_audss EXYNOS_DOUT_AUD_BUS>,
-				<&clock_audss EXYNOS_DOUT_I2S>;
-
-		assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
-				<&clock CLK_MOUT_EPLL>,
-				<&clock CLK_MOUT_MAU_EPLL>,
-				<&clock CLK_MAU_EPLL>,
-				<&clock_audss EXYNOS_MOUT_AUDSS>;
-
-		assigned-clock-rates = <0>,
-				<0>,
-				<0>,
-				<0>,
-				<0>,
-				<196608001>,
-				<(196608002 / 2)>,
-				<196608000>;
+		audio-routing = "I2S Playback", "Mixer DAI TX";
 
 		cpu {
 			sound-dai = <&i2s0 0>, <&i2s0 1>;
@@ -69,17 +47,35 @@
 	};
 };
 
-&clock_audss {
-	assigned-clocks = <&clock_audss EXYNOS_DOUT_SRP>,
-			  <&clock CLK_FOUT_EPLL>;
-	assigned-clock-rates = <(196608000 / 256)>,
-			       <196608000>;
-};
-
 &i2s0 {
 	status = "okay";
-	assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>;
-	assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>;
+
+	assigned-clocks = <&clock CLK_MOUT_EPLL>,
+			  <&clock CLK_MOUT_MAU_EPLL>,
+			  <&clock CLK_MOUT_USER_MAU_EPLL>,
+			  <&clock_audss EXYNOS_MOUT_AUDSS>,
+			  <&clock_audss EXYNOS_MOUT_I2S>,
+			  <&i2s0 CLK_I2S_RCLK_SRC>,
+			  <&clock_audss EXYNOS_DOUT_SRP>,
+			  <&clock_audss EXYNOS_DOUT_AUD_BUS>,
+			  <&clock_audss EXYNOS_DOUT_I2S>;
+
+	assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
+				 <&clock CLK_MOUT_EPLL>,
+				 <&clock CLK_MOUT_MAU_EPLL>,
+				 <&clock CLK_MAU_EPLL>,
+				 <&clock_audss EXYNOS_MOUT_AUDSS>,
+				 <&clock_audss EXYNOS_SCLK_I2S>;
+
+	assigned-clock-rates = <0>,
+			       <0>,
+			       <0>,
+			       <0>,
+			       <0>,
+			       <0>,
+			       <196608001>,
+			       <(196608002 / 2)>,
+			       <196608000>;
 };
 
 &pwm {
diff --git a/arch/arm/boot/dts/samsung/exynos5422-samsung-k3g.dts b/arch/arm/boot/dts/samsung/exynos5422-samsung-k3g.dts
new file mode 100644
index 000000000000..c35261a338ff
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/exynos5422-samsung-k3g.dts
@@ -0,0 +1,679 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Galaxy S5 (SM-G900H) device-tree source
+ *
+ * Copyright (c) 2023 Markuss Broks
+ */
+
+/dts-v1/;
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "exynos5800.dtsi"
+#include "exynos5422-cpus.dtsi"
+
+/ {
+	model = "Samsung Galaxy S5 (SM-G900H)";
+	compatible = "samsung,k3g", "samsung,exynos5800", \
+		     "samsung,exynos5";
+
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &mmc_0;
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x80000000>; /* 2 GiB */
+	};
+
+	fixed-rate-clocks {
+		oscclk {
+			compatible = "samsung,exynos5420-oscclk";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	firmware@2073000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x02073000 0x1000>;
+	};
+
+	tsp_vdd: regulator-tsp-vdd-en {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_vdd_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpy3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&cpu4 {
+	cpu-supply = <&buck6_reg>;
+};
+
+&gpu {
+	status = "okay";
+	mali-supply = <&buck4_reg>;
+};
+
+&hsi2c_7 {
+	status = "okay";
+
+	pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+
+		interrupt-parent = <&gpx0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-source;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&s2mps11_irq>;
+
+		s2mps11_osc: clocks {
+			compatible = "samsung,s2mps11-clk";
+			#clock-cells = <1>;
+			clock-output-names = "s2mps11_ap",
+					     "s2mps11_cp", "s2mps11_bt";
+		};
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_ARM";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_INT";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_G3D";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "VDD_MEM";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "VDD_KFC";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "VIN_LLDO";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "VIN_MLDO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-always-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "VIN_HLDO";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3500000>;
+				regulator-always-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "VDD_CAM_ISP";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3550000>;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ALIVE";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_APIO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "VDD_APIO_MMC01";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "VDD_ADC";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "VDD_HRM_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "VDD_MIPI";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "VDD_MIPI_PLL_ABB1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "VDD_VTF";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "VDD_UOTG";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "VDDQ_PRE";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "VDD_HSIC_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "VDD_HSIC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "VDD_APIO_MMC2";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo14_reg: LDO14 {
+				regulator-name = "VDD_MOTOR";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "VDD_CAM1_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "VDD_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo17_reg: LDO17 {
+				/* Unused */
+				regulator-name = "VDD_LDO17";
+			};
+
+			ldo18_reg: LDO18 {
+				regulator-name = "VDD_CODEC";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "VDD_VMMC";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "VDD_CAM1_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "VDD_CAM_IO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo22_reg: LDO22 {
+				regulator-name = "VDD_CAM0_S_CORE";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "VDD_MIFS";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "VDD_MHL_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo25_reg: LDO25 {
+				regulator-name = "VDD_LCD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "VDD_CAM0_AF";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "VDD_G3DS";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo28_reg: LDO28 {
+				regulator-name = "VDD_LCD_3V0";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo29_reg: LDO29 {
+				/* Unused */
+				regulator-name = "VDD_LDO29";
+			};
+
+			ldo30_reg: LDO30 {
+				regulator-name = "VDD_TOUCH";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo31_reg: LDO31 {
+				regulator-name = "VDD_COMP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo32_reg: LDO32 {
+				regulator-name = "VDD_TOUCH_IO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo33_reg: LDO33 {
+				regulator-name = "VDD_MHL_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo34_reg: LDO34 {
+				regulator-name = "VDD_HRM_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo35_reg: LDO35 {
+				regulator-name = "VDD_SIL";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo36_reg: LDO36 {
+				/* Unused */
+				regulator-name = "VDD_LDO36";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo37_reg: LDO37 {
+				/* Unused */
+				regulator-name = "VDD_LDO37";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo38_reg: LDO38 {
+				regulator-name = "VDD_KEY_LED";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c_0 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		interrupt-parent = <&gpx1>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		vio-supply = <&ldo32_reg>;
+		vdd-supply = <&tsp_vdd>;
+		syna,startup-delay-ms = <100>;
+
+		pinctrl-0 = <&touch_irq>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+/* eMMC flash */
+&mmc_0 {
+	status = "okay";
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	cap-mmc-highspeed;
+	non-removable;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-hs400-timing = <0 2>;
+	samsung,read-strobe-delay = <90>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_rclk>;
+	bus-width = <8>;
+};
+
+&pinctrl_0 {
+	s2mps11_irq: s2mps11-irq-pins {
+		samsung,pins = "gpx0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	touch_irq: touch-irq-pins {
+		samsung,pins = "gpx1-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&timer {
+	arm,cpu-registers-not-fw-configured;
+};
+
+&tmu_cpu0 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_gpu {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&usbdrd_dwc3_0 {
+	dr_mode = "peripheral";
+};
+
+&usbdrd_dwc3_1 {
+	dr_mode = "peripheral";
+};
+
+&usbdrd3_0 {
+	vdd33-supply = <&ldo9_reg>;
+	vdd10-supply = <&ldo11_reg>;
+};
+
+&usbdrd3_1 {
+	vdd33-supply = <&ldo9_reg>;
+	vdd10-supply = <&ldo11_reg>;
+};
diff --git a/arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi b/arch/arm/boot/dts/samsung/exynos54xx-odroidxu-leds.dtsi
index 56acd832f0b3..8c0e1716c0b3 100644
--- a/arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos54xx-odroidxu-leds.dtsi
@@ -9,36 +9,43 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
-	pwmleds {
+	led-controller-1 {
 		compatible = "pwm-leds";
 
-		greenled {
+		led-1 {
 			label = "green:mmc0";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			color = <LED_COLOR_ID_GREEN>;
 			pwms = <&pwm 1 2000000 0>;
 			pwm-names = "pwm1";
 			/*
 			 * Green LED is much brighter than the others
 			 * so limit its max brightness
 			 */
-			max_brightness = <127>;
+			max-brightness = <127>;
 			linux,default-trigger = "mmc0";
 		};
 
-		blueled {
-			label = "blue:heartbeat";
+		led-2 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			pwms = <&pwm 2 2000000 0>;
 			pwm-names = "pwm2";
-			max_brightness = <255>;
+			max-brightness = <255>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	gpioleds {
+	led-controller-2 {
 		compatible = "gpio-leds";
-		redled {
+
+		led-3 {
 			label = "red:microSD";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "mmc1";
diff --git a/arch/arm/boot/dts/exynos54xx.dtsi b/arch/arm/boot/dts/samsung/exynos54xx.dtsi
index f78dee801cd9..5c799886c275 100644
--- a/arch/arm/boot/dts/exynos54xx.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos54xx.dtsi
@@ -62,19 +62,20 @@
 			#size-cells = <1>;
 			ranges = <0 0x02020000 0x54000>;
 
-			smp-sysram@0 {
+			smp-sram@0 {
 				compatible = "samsung,exynos4210-sysram";
 				reg = <0x0 0x1000>;
 			};
 
-			smp-sysram@53000 {
+			smp-sram@53000 {
 				compatible = "samsung,exynos4210-sysram-ns";
 				reg = <0x53000 0x1000>;
 			};
 		};
 
 		mct: timer@101c0000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos5420-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x101c0000 0xb00>;
 			interrupts-extended = <&combiner 23 3>,
 					      <&combiner 23 4>,
@@ -101,7 +102,6 @@
 			reg = <0x12d10000 0x100>;
 			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 			status = "disabled";
 		};
 
@@ -142,15 +142,15 @@
 			status = "disabled";
 		};
 
-		usbdrd3_0: usb3-0 {
+		usbdrd3_0: usb@12000000 {
 			compatible = "samsung,exynos5250-dwusb3";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x0 0x12000000 0x10000>;
 
-			usbdrd_dwc3_0: dwc3@12000000 {
+			usbdrd_dwc3_0: usb@0 {
 				compatible = "snps,dwc3";
-				reg = <0x12000000 0x10000>;
+				reg = <0x0 0x10000>;
 				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usbdrd_phy0 0>, <&usbdrd_phy0 1>;
 				phy-names = "usb2-phy", "usb3-phy";
@@ -164,15 +164,15 @@
 			#phy-cells = <1>;
 		};
 
-		usbdrd3_1: usb3-1 {
+		usbdrd3_1: usb@12400000 {
 			compatible = "samsung,exynos5250-dwusb3";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x0 0x12400000 0x10000>;
 
-			usbdrd_dwc3_1: dwc3@12400000 {
+			usbdrd_dwc3_1: usb@0 {
 				compatible = "snps,dwc3";
-				reg = <0x12400000 0x10000>;
+				reg = <0x0 0x10000>;
 				phys = <&usbdrd_phy1 0>, <&usbdrd_phy1 1>;
 				phy-names = "usb2-phy", "usb3-phy";
 				snps,dis_u3_susphy_quirk;
@@ -189,7 +189,7 @@
 			compatible = "samsung,exynos4210-ehci";
 			reg = <0x12110000 0x100>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb2_phy 1>;
+			phys = <&usb2_phy 0>;
 			phy-names = "host";
 		};
 
@@ -197,12 +197,12 @@
 			compatible = "samsung,exynos4210-ohci";
 			reg = <0x12120000 0x100>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb2_phy 1>;
+			phys = <&usb2_phy 0>;
 			phy-names = "host";
 		};
 
 		usb2_phy: phy@12130000 {
-			compatible = "samsung,exynos5250-usb2-phy";
+			compatible = "samsung,exynos5420-usb2-phy";
 			reg = <0x12130000 0x100>;
 			#phy-cells = <1>;
 		};
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/samsung/exynos5800-peach-pi.dts
index 60ca3d685247..f91bc4ae008e 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/samsung/exynos5800-peach-pi.dts
@@ -24,10 +24,14 @@
 		"google,pi-rev11", "google,pi-rev10",
 		"google,pi", "google,peach", "samsung,exynos5800",
 		"samsung,exynos5";
+	chassis-type = "laptop";
 
 	aliases {
 		/* Assign 20 so we don't get confused w/ builtin ones */
 		i2c20 = &i2c_tunnel;
+		mmc0 = &mmc_0; /* eMMC */
+		mmc1 = &mmc_2; /* SD */
+		mmc2 = &mmc_1; /* WiFi */
 	};
 
 	backlight: backlight {
@@ -58,7 +62,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq &lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -138,7 +142,7 @@
 		};
 	};
 
-	mmc1_pwrseq: mmc1_pwrseq {
+	mmc1_pwrseq: mmc1-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpx0 0 GPIO_ACTIVE_LOW>; /* WIFI_EN */
 		clocks = <&max77802 MAX77802_CLK_32K_CP>;
@@ -156,6 +160,15 @@
 	assigned-clock-parents = <&clock CLK_MAU_EPLL>;
 };
 
+/*
+ * Peach Pi board uses SoC revision with lower maximum frequency for A7 cores
+ * (1.3 GHz instead of 1.4 GHz) than Odroid XU3/XU4 boards.  Thus we need to
+ * update A7 OPPs table accordingly.
+ */
+&cluster_a7_opp_table {
+	/delete-node/opp-1400000000;
+};
+
 &cpu0 {
 	cpu-supply = <&buck2_reg>;
 };
@@ -205,13 +218,13 @@
 	status = "okay";
 	clock-frequency = <400000>;
 
-	max77802: max77802-pmic@9 {
+	max77802: pmic@9 {
 		compatible = "maxim,max77802";
 		interrupt-parent = <&gpx3>;
 		interrupts = <1 IRQ_TYPE_NONE>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77802_irq>, <&pmic_selb>,
-			    <&pmic_dvs_1>, <&pmic_dvs_2>, <&pmic_dvs_3>;
+			    <&pmic_dvs_1>, <&pmic_dvs_2>;
 		wakeup-source;
 		reg = <0x9>;
 		#clock-cells = <1>;
@@ -257,6 +270,8 @@
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-ramp-delay = <12500>;
+				regulator-coupled-with = <&buck3_reg>;
+				regulator-coupled-max-spread = <300000>;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};
@@ -269,6 +284,8 @@
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-ramp-delay = <12500>;
+				regulator-coupled-with = <&buck2_reg>;
+				regulator-coupled-max-spread = <300000>;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};
@@ -689,6 +706,7 @@
 /* eMMC flash */
 &mmc_0 {
 	status = "okay";
+	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	mmc-hs400-1_8v;
 	cap-mmc-highspeed;
@@ -742,14 +760,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mask_tpm_reset>;
 
-	wifi_en: wifi-en {
+	wifi_en: wifi-en-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max98091_irq: max98091-irq {
+	max98091_irq: max98091-irq-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -757,7 +775,7 @@
 	};
 
 	/* We need GPX0_6 to be low at sleep time; just keep it low always */
-	mask_tpm_reset: mask-tpm-reset {
+	mask_tpm_reset: mask-tpm-reset-pins {
 		samsung,pins = "gpx0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -765,70 +783,70 @@
 		samsung,pin-val = <0>;
 	};
 
-	tpm_irq: tpm-irq {
+	tpm_irq: tpm-irq-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	trackpad_irq: trackpad-irq {
+	trackpad_irq: trackpad-irq-pins {
 		samsung,pins = "gpx1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	tps65090_irq: tps65090-irq {
+	tps65090_irq: tps65090-irq-pins {
 		samsung,pins = "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	dp_hpd_gpio: dp_hpd_gpio {
+	dp_hpd_gpio: dp-hpd-gpio-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max77802_irq: max77802-irq {
+	max77802_irq: max77802-irq-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_dvs_1: pmic-dvs-1 {
+	pmic_dvs_1: pmic-dvs-1-pins {
 		samsung,pins = "gpy7-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -836,74 +854,67 @@
 	};
 };
 
-&pinctrl_1 {
-	/* Adjust WiFi drive strengths lower for EMI */
-	sd1_clk: sd1-clk {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+/* pinctrl_1 */
+/* Adjust WiFi drive strengths lower for EMI */
+&sd1_bus1 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_cmd: sd1-cmd {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus4 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus1: sd1-bus-width1 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus8 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus4: sd1-bus-width4 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_clk {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus8: sd1-bus-width8 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_cmd {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_2 {
-	pmic_dvs_2: pmic-dvs-2 {
-		samsung,pins = "gpj4-2";
+	pmic_dvs_2: pmic-dvs-2-pins {
+		samsung,pins = "gpj4-2", "gpj4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
+};
 
-	pmic_dvs_3: pmic-dvs-3 {
-		samsung,pins = "gpj4-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
-	};
+/* pinctrl_3*/
+/* Drive SPI lines at x2 for better integrity */
+&spi2_bus {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_3 {
-	/* Drive SPI lines at x2 for better integrity */
-	spi2-bus {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
-
 	/* Drive SPI chip select at x2 for better integrity */
-	ec_spi_cs: ec-spi-cs {
+	ec_spi_cs: ec-spi-cs-pins {
 		samsung,pins = "gpb1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 	};
 
-	usb300_vbus_en: usb300-vbus-en {
+	usb300_vbus_en: usb300-vbus-en-pins {
 		samsung,pins = "gph0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb301_vbus_en: usb301-vbus-en {
+	usb301_vbus_en: usb301-vbus-en-pins {
 		samsung,pins = "gph0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_selb: pmic-selb {
+	pmic_selb: pmic-selb-pins {
 		samsung,pins = "gph0-2", "gph0-3", "gph0-4", "gph0-5",
 			       "gph0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -1058,6 +1069,16 @@
 	vtmu-supply = <&ldo10_reg>;
 };
 
+&usbdrd3_0 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 &usbdrd_dwc3_0 {
 	dr_mode = "host";
 };
@@ -1083,5 +1104,5 @@
 	timeout-sec = <32>;
 };
 
-#include "cros-ec-keyboard.dtsi"
-#include "cros-adc-thermistors.dtsi"
+#include "../cros-ec-keyboard.dtsi"
+#include "../cros-adc-thermistors.dtsi"
diff --git a/arch/arm/boot/dts/exynos5800.dtsi b/arch/arm/boot/dts/samsung/exynos5800.dtsi
index 16177d815ee4..72d3a3535a7a 100644
--- a/arch/arm/boot/dts/exynos5800.dtsi
+++ b/arch/arm/boot/dts/samsung/exynos5800.dtsi
@@ -1,13 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * SAMSUNG EXYNOS5800 SoC device tree source
+ * Samsung Exynos5800 SoC device tree source
  *
  * Copyright (c) 2014 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * SAMSUNG EXYNOS5800 SoC device nodes are listed in this file.
- * EXYNOS5800 based board files can include this file and provide
- * values for board specfic bindings.
+ * Samsung Exynos5800 SoC device nodes are listed in this file.
+ * Exynos5800 based board files can include this file and provide
+ * values for board specific bindings.
  */
 
 #include "exynos5420.dtsi"
@@ -21,67 +21,87 @@
 };
 
 &cluster_a15_opp_table {
+	opp-2000000000 {
+		opp-hz = /bits/ 64 <2000000000>;
+		opp-microvolt = <1312500 1312500 1500000>;
+		clock-latency-ns = <140000>;
+	};
+	opp-1900000000 {
+		opp-hz = /bits/ 64 <1900000000>;
+		opp-microvolt = <1262500 1262500 1500000>;
+		clock-latency-ns = <140000>;
+	};
+	opp-1800000000 {
+		opp-hz = /bits/ 64 <1800000000>;
+		opp-microvolt = <1237500 1237500 1500000>;
+		clock-latency-ns = <140000>;
+	};
 	opp-1700000000 {
-		opp-microvolt = <1250000>;
+		opp-microvolt = <1250000 1250000 1500000>;
 	};
 	opp-1600000000 {
-		opp-microvolt = <1250000>;
+		opp-microvolt = <1250000 1250000 1500000>;
 	};
 	opp-1500000000 {
-		opp-microvolt = <1100000>;
+		opp-microvolt = <1100000 1100000 1500000>;
 	};
 	opp-1400000000 {
-		opp-microvolt = <1100000>;
+		opp-microvolt = <1100000 1100000 1500000>;
 	};
 	opp-1300000000 {
-		opp-microvolt = <1100000>;
+		opp-microvolt = <1100000 1100000 1500000>;
 	};
 	opp-1200000000 {
-		opp-microvolt = <1000000>;
+		opp-microvolt = <1000000 1000000 1500000>;
 	};
 	opp-1100000000 {
-		opp-microvolt = <1000000>;
+		opp-microvolt = <1000000 1000000 1500000>;
 	};
 	opp-1000000000 {
-		opp-microvolt = <1000000>;
+		opp-microvolt = <1000000 1000000 1500000>;
 	};
 	opp-900000000 {
-		opp-microvolt = <1000000>;
+		opp-microvolt = <1000000 1000000 1500000>;
 	};
 	opp-800000000 {
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 	};
 	opp-700000000 {
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 	};
 	opp-600000000 {
 		opp-hz = /bits/ 64 <600000000>;
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 		clock-latency-ns = <140000>;
 	};
 	opp-500000000 {
 		opp-hz = /bits/ 64 <500000000>;
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 		clock-latency-ns = <140000>;
 	};
 	opp-400000000 {
 		opp-hz = /bits/ 64 <400000000>;
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 		clock-latency-ns = <140000>;
 	};
 	opp-300000000 {
 		opp-hz = /bits/ 64 <300000000>;
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 		clock-latency-ns = <140000>;
 	};
 	opp-200000000 {
 		opp-hz = /bits/ 64 <200000000>;
-		opp-microvolt = <900000>;
+		opp-microvolt = <900000 900000 1500000>;
 		clock-latency-ns = <140000>;
 	};
 };
 
 &cluster_a7_opp_table {
+	opp-1400000000 {
+		opp-hz = /bits/ 64 <1400000000>;
+		opp-microvolt = <1275000>;
+		clock-latency-ns = <140000>;
+	};
 	opp-1300000000 {
 		opp-microvolt = <1250000>;
 	};
@@ -128,6 +148,10 @@
 	};
 };
 
+&dsi {
+	compatible = "samsung,exynos5422-mipi-dsi";
+};
+
 &mfc {
 	compatible = "samsung,mfc-v8";
 };
diff --git a/arch/arm/boot/dts/s3c6400.dtsi b/arch/arm/boot/dts/samsung/s3c6400.dtsi
index 8c28e8a0c824..7cc785a63866 100644
--- a/arch/arm/boot/dts/s3c6400.dtsi
+++ b/arch/arm/boot/dts/samsung/s3c6400.dtsi
@@ -5,7 +5,7 @@
  * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
  *
  * Samsung's S3C6400 SoC device nodes are listed in this file. S3C6400
- * based board files can include this file and provide values for board specfic
+ * based board files can include this file and provide values for board specific
  * bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
diff --git a/arch/arm/boot/dts/s3c6410-mini6410.dts b/arch/arm/boot/dts/samsung/s3c6410-mini6410.dts
index 1aeac33b0d34..0b07b3c31960 100644
--- a/arch/arm/boot/dts/s3c6410-mini6410.dts
+++ b/arch/arm/boot/dts/samsung/s3c6410-mini6410.dts
@@ -28,29 +28,21 @@
 		bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1";
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fin_pll: oscillator@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			clock-frequency = <12000000>;
-			clock-output-names = "fin_pll";
-			#clock-cells = <0>;
-		};
+	fin_pll: oscillator-0 {
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+		clock-output-names = "fin_pll";
+		#clock-cells = <0>;
+	};
 
-		xusbxti: oscillator@1 {
-			compatible = "fixed-clock";
-			reg = <1>;
-			clock-output-names = "xusbxti";
-			clock-frequency = <48000000>;
-			#clock-cells = <0>;
-		};
+	xusbxti: oscillator-1 {
+		compatible = "fixed-clock";
+		clock-output-names = "xusbxti";
+		clock-frequency = <48000000>;
+		#clock-cells = <0>;
 	};
 
-	srom-cs1@18000000 {
+	srom-cs1-bus@18000000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -59,7 +51,7 @@
 
 		ethernet@18000000 {
 			compatible = "davicom,dm9000";
-			reg = <0x18000000 0x2 0x18000004 0x2>;
+			reg = <0x18000000 0x2>, <0x18000004 0x2>;
 			interrupt-parent = <&gpn>;
 			interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
 			davicom,no-eeprom;
@@ -201,12 +193,12 @@
 };
 
 &pinctrl0 {
-	gpio_leds: gpio-leds {
+	gpio_leds: gpio-leds-pins {
 		samsung,pins = "gpk-4", "gpk-5", "gpk-6", "gpk-7";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	gpio_keys: gpio-keys {
+	gpio_keys: gpio-keys-pins {
 		samsung,pins = "gpn-0", "gpn-1", "gpn-2", "gpn-3",
 				"gpn-4", "gpn-5", "gpl-11", "gpl-12";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/s3c6410-smdk6410.dts b/arch/arm/boot/dts/samsung/s3c6410-smdk6410.dts
index 3bf6c450a26e..581309e7f15e 100644
--- a/arch/arm/boot/dts/s3c6410-smdk6410.dts
+++ b/arch/arm/boot/dts/samsung/s3c6410-smdk6410.dts
@@ -4,7 +4,7 @@
  *
  * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
  *
- * Device tree source file for SAMSUNG SMDK6410 board which is based on
+ * Device tree source file for Samsung SMDK6410 board which is based on
  * Samsung's S3C6410 SoC.
  */
 
@@ -16,8 +16,8 @@
 #include "s3c6410.dtsi"
 
 / {
-	model = "SAMSUNG SMDK6410 board based on S3C6410";
-	compatible = "samsung,mini6410", "samsung,s3c6410";
+	model = "Samsung SMDK6410 board based on S3C6410";
+	compatible = "samsung,smdk6410", "samsung,s3c6410";
 
 	memory@50000000 {
 		device_type = "memory";
@@ -28,29 +28,21 @@
 		bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1";
 	};
 
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fin_pll: oscillator@0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			clock-frequency = <12000000>;
-			clock-output-names = "fin_pll";
-			#clock-cells = <0>;
-		};
+	fin_pll: oscillator-0 {
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+		clock-output-names = "fin_pll";
+		#clock-cells = <0>;
+	};
 
-		xusbxti: oscillator@1 {
-			compatible = "fixed-clock";
-			reg = <1>;
-			clock-output-names = "xusbxti";
-			clock-frequency = <48000000>;
-			#clock-cells = <0>;
-		};
+	xusbxti: oscillator-1 {
+		compatible = "fixed-clock";
+		clock-output-names = "xusbxti";
+		clock-frequency = <48000000>;
+		#clock-cells = <0>;
 	};
 
-	srom-cs1@18000000 {
+	srom-cs1-bus@18000000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/s3c6410.dtsi b/arch/arm/boot/dts/samsung/s3c6410.dtsi
index a766d6de696c..13e9cc69b8a8 100644
--- a/arch/arm/boot/dts/s3c6410.dtsi
+++ b/arch/arm/boot/dts/samsung/s3c6410.dtsi
@@ -5,7 +5,7 @@
  * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
  *
  * Samsung's S3C6410 SoC device nodes are listed in this file. S3C6410
- * based board files can include this file and provide values for board specfic
+ * based board files can include this file and provide values for board specific
  * bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
diff --git a/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi b/arch/arm/boot/dts/samsung/s3c64xx-pinctrl.dtsi
index 8e9594d64b57..f53959b7d031 100644
--- a/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
+++ b/arch/arm/boot/dts/samsung/s3c64xx-pinctrl.dtsi
@@ -9,118 +9,118 @@
  * listed as device tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "s3c64xx-pinctrl.h"
 
 &pinctrl0 {
 	/*
 	 * Pin banks
 	 */
 
-	gpa: gpa {
+	gpa: gpa-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpc: gpc {
+	gpc: gpc-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpd: gpd {
+	gpd: gpd-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpe: gpe {
+	gpe: gpe-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpf: gpf {
+	gpf: gpf-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpg: gpg {
+	gpg: gpg-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gph: gph {
+	gph: gph-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpi: gpi {
+	gpi: gpi-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpj: gpj {
+	gpj: gpj-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpk: gpk {
+	gpk: gpk-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpl: gpl {
+	gpl: gpl-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpm: gpm {
+	gpm: gpm-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpn: gpn {
+	gpn: gpn-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpo: gpo {
+	gpo: gpo-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpp: gpp {
+	gpp: gpp-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpq: gpq {
+	gpq: gpq-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -131,552 +131,552 @@
 	 * Pin groups
 	 */
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa-0", "gpa-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa-2", "gpa-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa-4", "gpa-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa-6", "gpa-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpb-0", "gpb-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ext_dma_0: ext-dma-0 {
+	ext_dma_0: ext-dma-0-pins {
 		samsung,pins = "gpb-0", "gpb-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ext_dma_1: ext-dma-1 {
+	ext_dma_1: ext-dma-1-pins {
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_data_0: irda-data-0 {
+	irda_data_0: irda-data-0-pins {
 		samsung,pins = "gpb-0", "gpb-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_data_1: irda-data-1 {
+	irda_data_1: irda-data-1-pins {
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_sdbw: irda-sdbw {
+	irda_sdbw: irda-sdbw-pins {
 		samsung,pins = "gpb-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb-5", "gpb-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_6>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_6>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpc-0", "gpc-1", "gpc-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi0_cs: spi0-cs {
+	spi0_cs: spi0-cs-pins {
 		samsung,pins = "gpc-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpc-4", "gpc-5", "gpc-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi1_cs: spi1-cs {
+	spi1_cs: spi1-cs-pins {
 		samsung,pins = "gpc-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpg-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpg-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_bus1: sd0-bus1 {
+	sd0_bus1: sd0-bus1-pins {
 		samsung,pins = "gpg-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_bus4: sd0-bus4 {
+	sd0_bus4: sd0-bus4-pins {
 		samsung,pins = "gpg-2", "gpg-3", "gpg-4", "gpg-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpg-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gph-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gph-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus1: sd1-bus1 {
+	sd1_bus1: sd1-bus1-pins {
 		samsung,pins = "gph-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus4: sd1-bus4 {
+	sd1_bus4: sd1-bus4-pins {
 		samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus8: sd1-bus8 {
+	sd1_bus8: sd1-bus8-pins {
 		samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5",
 				"gph-6", "gph-7", "gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpg-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_bus1: sd2-bus1 {
+	sd2_bus1: sd2-bus1-pins {
 		samsung,pins = "gph-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_bus4: sd2-bus4 {
+	sd2_bus4: sd2-bus4-pins {
 		samsung,pins = "gph-6", "gph-7", "gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s0_cdclk: i2s0-cdclk {
+	i2s0_cdclk: i2s0-cdclk-pins {
 		samsung,pins = "gpd-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s1_cdclk: i2s1-cdclk {
+	i2s1_cdclk: i2s1-cdclk-pins {
 		samsung,pins = "gpe-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpc-4", "gpc-5", "gpc-6", "gph-6",
 				"gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_5>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s2_cdclk: i2s2-cdclk {
+	i2s2_cdclk: i2s2-cdclk-pins {
 		/* S3C6410-only */
 		samsung,pins = "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_5>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm0_extclk: pcm0-extclk {
+	pcm0_extclk: pcm0-extclk-pins {
 		samsung,pins = "gpd-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm1_extclk: pcm1-extclk {
+	pcm1_extclk: pcm1-extclk-pins {
 		samsung,pins = "gpe-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ac97_bus_0: ac97-bus-0 {
+	ac97_bus_0: ac97-bus-0-pins {
 		samsung,pins = "gpd-0", "gpd-1", "gpd-2", "gpd-3", "gpd-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ac97_bus_1: ac97-bus-1 {
+	ac97_bus_1: ac97-bus-1-pins {
 		samsung,pins = "gpe-0", "gpe-1", "gpe-2", "gpe-3", "gpe-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_port: cam-port {
+	cam_port: cam-port-pins {
 		samsung,pins = "gpf-0", "gpf-1", "gpf-2", "gpf-4",
 				"gpf-5", "gpf-6", "gpf-7", "gpf-8",
 				"gpf-9", "gpf-10", "gpf-11", "gpf-12";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_rst: cam-rst {
+	cam_rst: cam-rst-pins {
 		samsung,pins = "gpf-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_field: cam-field {
+	cam_field: cam-field-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpb-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm_extclk: pwm-extclk {
+	pwm_extclk: pwm-extclk-pins {
 		samsung,pins = "gpf-13";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpf-14";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpf-15";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	clkout0: clkout-0 {
+	clkout0: clkout-0-pins {
 		samsung,pins = "gpf-14";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col0_0: keypad-col0-0 {
+	keypad_col0_0: keypad-col0-0-pins {
 		samsung,pins = "gph-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col1_0: keypad-col1-0 {
+	keypad_col1_0: keypad-col1-0-pins {
 		samsung,pins = "gph-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col2_0: keypad-col2-0 {
+	keypad_col2_0: keypad-col2-0-pins {
 		samsung,pins = "gph-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col3_0: keypad-col3-0 {
+	keypad_col3_0: keypad-col3-0-pins {
 		samsung,pins = "gph-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col4_0: keypad-col4-0 {
+	keypad_col4_0: keypad-col4-0-pins {
 		samsung,pins = "gph-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col5_0: keypad-col5-0 {
+	keypad_col5_0: keypad-col5-0-pins {
 		samsung,pins = "gph-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col6_0: keypad-col6-0 {
+	keypad_col6_0: keypad-col6-0-pins {
 		samsung,pins = "gph-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col7_0: keypad-col7-0 {
+	keypad_col7_0: keypad-col7-0-pins {
 		samsung,pins = "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col0_1: keypad-col0-1 {
+	keypad_col0_1: keypad-col0-1-pins {
 		samsung,pins = "gpl-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col1_1: keypad-col1-1 {
+	keypad_col1_1: keypad-col1-1-pins {
 		samsung,pins = "gpl-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col2_1: keypad-col2-1 {
+	keypad_col2_1: keypad-col2-1-pins {
 		samsung,pins = "gpl-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col3_1: keypad-col3-1 {
+	keypad_col3_1: keypad-col3-1-pins {
 		samsung,pins = "gpl-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col4_1: keypad-col4-1 {
+	keypad_col4_1: keypad-col4-1-pins {
 		samsung,pins = "gpl-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col5_1: keypad-col5-1 {
+	keypad_col5_1: keypad-col5-1-pins {
 		samsung,pins = "gpl-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col6_1: keypad-col6-1 {
+	keypad_col6_1: keypad-col6-1-pins {
 		samsung,pins = "gpl-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col7_1: keypad-col7-1 {
+	keypad_col7_1: keypad-col7-1-pins {
 		samsung,pins = "gpl-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row0_0: keypad-row0-0 {
+	keypad_row0_0: keypad-row0-0-pins {
 		samsung,pins = "gpk-8";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row1_0: keypad-row1-0 {
+	keypad_row1_0: keypad-row1-0-pins {
 		samsung,pins = "gpk-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row2_0: keypad-row2-0 {
+	keypad_row2_0: keypad-row2-0-pins {
 		samsung,pins = "gpk-10";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row3_0: keypad-row3-0 {
+	keypad_row3_0: keypad-row3-0-pins {
 		samsung,pins = "gpk-11";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row4_0: keypad-row4-0 {
+	keypad_row4_0: keypad-row4-0-pins {
 		samsung,pins = "gpk-12";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row5_0: keypad-row5-0 {
+	keypad_row5_0: keypad-row5-0-pins {
 		samsung,pins = "gpk-13";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row6_0: keypad-row6-0 {
+	keypad_row6_0: keypad-row6-0-pins {
 		samsung,pins = "gpk-14";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row7_0: keypad-row7-0 {
+	keypad_row7_0: keypad-row7-0-pins {
 		samsung,pins = "gpk-15";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row0_1: keypad-row0-1 {
+	keypad_row0_1: keypad-row0-1-pins {
 		samsung,pins = "gpn-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row1_1: keypad-row1-1 {
+	keypad_row1_1: keypad-row1-1-pins {
 		samsung,pins = "gpn-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row2_1: keypad-row2-1 {
+	keypad_row2_1: keypad-row2-1-pins {
 		samsung,pins = "gpn-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row3_1: keypad-row3-1 {
+	keypad_row3_1: keypad-row3-1-pins {
 		samsung,pins = "gpn-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row4_1: keypad-row4-1 {
+	keypad_row4_1: keypad-row4-1-pins {
 		samsung,pins = "gpn-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row5_1: keypad-row5-1 {
+	keypad_row5_1: keypad-row5-1-pins {
 		samsung,pins = "gpn-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row6_1: keypad-row6-1 {
+	keypad_row6_1: keypad-row6-1-pins {
 		samsung,pins = "gpn-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row7_1: keypad-row7-1 {
+	keypad_row7_1: keypad-row7-1-pins {
 		samsung,pins = "gpn-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpj-8", "gpj-9", "gpj-10", "gpj-11";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpi-3", "gpi-4", "gpi-5", "gpi-6",
 				"gpi-7", "gpi-10", "gpi-11", "gpi-12",
 				"gpi-13", "gpi-14", "gpi-15", "gpj-3",
 				"gpj-4", "gpj-5", "gpj-6", "gpj-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpi-2", "gpi-3", "gpi-4", "gpi-5",
 				"gpi-6", "gpi-7", "gpi-10", "gpi-11",
 				"gpi-12", "gpi-13", "gpi-14", "gpi-15",
 				"gpj-2", "gpj-3", "gpj-4", "gpj-5",
 				"gpj-6", "gpj-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
 				"gpi-4", "gpi-5", "gpi-6", "gpi-7",
 				"gpi-8", "gpi-9", "gpi-10", "gpi-11",
 				"gpi-12", "gpi-13", "gpi-14", "gpi-15",
 				"gpj-0", "gpj-1", "gpj-2", "gpj-3",
 				"gpj-4", "gpj-5", "gpj-6", "gpj-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	hsi_bus: hsi-bus {
+	hsi_bus: hsi-bus-pins {
 		samsung,pins = "gpk-0", "gpk-1", "gpk-2", "gpk-3",
 				"gpk-4", "gpk-5", "gpk-6", "gpk-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 };
diff --git a/arch/arm/boot/dts/samsung/s3c64xx-pinctrl.h b/arch/arm/boot/dts/samsung/s3c64xx-pinctrl.h
new file mode 100644
index 000000000000..645c591db357
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/s3c64xx-pinctrl.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung S3C64xx DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_S3C64XX_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_S3C64XX_PINCTRL_H__
+
+#define S3C64XX_PIN_PULL_NONE		0
+#define S3C64XX_PIN_PULL_DOWN		1
+#define S3C64XX_PIN_PULL_UP		2
+
+#define S3C64XX_PIN_FUNC_INPUT		0
+#define S3C64XX_PIN_FUNC_OUTPUT		1
+#define S3C64XX_PIN_FUNC_2		2
+#define S3C64XX_PIN_FUNC_3		3
+#define S3C64XX_PIN_FUNC_4		4
+#define S3C64XX_PIN_FUNC_5		5
+#define S3C64XX_PIN_FUNC_6		6
+#define S3C64XX_PIN_FUNC_EINT		7
+
+#endif /* __DTS_ARM_SAMSUNG_S3C64XX_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/s3c64xx.dtsi b/arch/arm/boot/dts/samsung/s3c64xx.dtsi
index 2e611df37911..0b59135ffe88 100644
--- a/arch/arm/boot/dts/s3c64xx.dtsi
+++ b/arch/arm/boot/dts/samsung/s3c64xx.dtsi
@@ -6,7 +6,7 @@
  *
  * Samsung's S3C64xx SoC series device nodes are listed in this file.
  * Particular SoCs from S3C64xx series can include this file and provide
- * values for SoCs specfic bindings.
+ * values for SoCs specific bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
  * S3C64xx SoCs. As device tree coverage for S3C64xx increases, additional
@@ -34,7 +34,7 @@
 
 		cpu@0 {
 			device_type = "cpu";
-			compatible = "arm,arm1176jzf-s", "arm,arm1176";
+			compatible = "arm,arm1176jzf-s";
 			reg = <0x0>;
 		};
 	};
@@ -59,7 +59,7 @@
 			#interrupt-cells = <1>;
 		};
 
-		sdhci0: sdhci@7c200000 {
+		sdhci0: mmc@7c200000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0x7c200000 0x100>;
 			interrupt-parent = <&vic1>;
@@ -70,7 +70,7 @@
 			status = "disabled";
 		};
 
-		sdhci1: sdhci@7c300000 {
+		sdhci1: mmc@7c300000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0x7c300000 0x100>;
 			interrupt-parent = <&vic1>;
@@ -81,7 +81,7 @@
 			status = "disabled";
 		};
 
-		sdhci2: sdhci@7c400000 {
+		sdhci2: mmc@7c400000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0x7c400000 0x100>;
 			interrupt-parent = <&vic1>;
@@ -178,20 +178,12 @@
 			interrupt-parent = <&vic1>;
 			interrupts = <21>;
 
-			pctrl_int_map: pinctrl-interrupt-map {
-				interrupt-map = <0 &vic0 0>,
-						<1 &vic0 1>,
-						<2 &vic1 0>,
-						<3 &vic1 1>;
-				#address-cells = <0>;
-				#size-cells = <0>;
-				#interrupt-cells = <1>;
-			};
-
 			wakeup-interrupt-controller {
 				compatible = "samsung,s3c64xx-wakeup-eint";
-				interrupts = <0>, <1>, <2>, <3>;
-				interrupt-parent = <&pctrl_int_map>;
+				interrupts-extended = <&vic0 0>,
+						      <&vic0 1>,
+						      <&vic1 0>,
+						      <&vic1 1>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/s5pv210-aquila.dts b/arch/arm/boot/dts/samsung/s5pv210-aquila.dts
index 14969b6529e8..0f5c6cd0f3a1 100644
--- a/arch/arm/boot/dts/s5pv210-aquila.dts
+++ b/arch/arm/boot/dts/samsung/s5pv210-aquila.dts
@@ -11,6 +11,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include "s5pv210.dtsi"
 
@@ -28,46 +29,43 @@
 
 	memory@30000000 {
 		device_type = "memory";
-		reg = <0x30000000 0x05000000
-			0x40000000 0x18000000>;
+		reg = <0x30000000 0x05000000>, <0x40000000 0x18000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	pmic_ap_clk: clock-0 {
+		/* Workaround for missing clock on PMIC */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
 
-		vtf_reg: fixed-regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "V_TF_2.8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&mp05 4 0>;
-			enable-active-high;
-		};
+	vtf_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_TF_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&mp05 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		pda_reg: fixed-regulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "VCC_1.8V_PDA";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			reg = <1>;
-		};
+	pda_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1.8V_PDA";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
 
-		bat_reg: fixed-regulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "V_BAT";
-			regulator-min-microvolt = <3700000>;
-			regulator-max-microvolt = <3700000>;
-			reg = <2>;
-		};
+	bat_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_BAT";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
 	};
 
 	i2c_pmic: i2c-pmic {
 		compatible = "i2c-gpio";
-		gpios = <&gpj4 0 0>, /* sda */
-			<&gpj4 3 0>; /* scl */
+		sda-gpios = <&gpj4 0 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpj4 3 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <2>;        /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -77,13 +75,13 @@
 			reg = <0x66>;
 
 			max8998,pmic-buck1-default-dvs-idx = <0>;
-			max8998,pmic-buck1-dvs-gpios = <&gph0 3 0>,
-							<&gph0 4 0>;
+			max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
+							<&gph0 4 GPIO_ACTIVE_HIGH>;
 			max8998,pmic-buck1-dvs-voltage = <1200000>, <1200000>,
 							<1200000>, <1200000>;
 
 			max8998,pmic-buck2-default-dvs-idx = <0>;
-			max8998,pmic-buck2-dvs-gpio = <&gph0 5 0>;
+			max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
 			max8998,pmic-buck2-dvs-voltage = <1200000>, <1200000>;
 
 			regulators {
@@ -228,6 +226,11 @@
 					regulator-always-on;
 				};
 
+				ap32khz_reg: EN32KHz-AP {
+					regulator-name = "32KHz AP";
+					regulator-always-on;
+				};
+
 				vichg_reg: ENVICHG {
 					regulator-name = "VICHG";
 				};
@@ -273,37 +276,37 @@
 			<&keypad_col0>, <&keypad_col1>, <&keypad_col2>;
 	status = "okay";
 
-	key_1 {
+	key-1 {
 		keypad,row = <0>;
 		keypad,column = <1>;
 		linux,code = <KEY_CONNECT>;
 	};
 
-	key_2 {
+	key-2 {
 		keypad,row = <0>;
 		keypad,column = <2>;
 		linux,code = <KEY_BACK>;
 	};
 
-	key_3 {
+	key-3 {
 		keypad,row = <1>;
 		keypad,column = <1>;
 		linux,code = <KEY_CAMERA_FOCUS>;
 	};
 
-	key_4 {
+	key-4 {
 		keypad,row = <1>;
 		keypad,column = <2>;
 		linux,code = <KEY_VOLUMEUP>;
 	};
 
-	key_5 {
+	key-5 {
 		keypad,row = <2>;
 		keypad,column = <1>;
 		linux,code = <KEY_CAMERA>;
 	};
 
-	key_6 {
+	key-6 {
 		keypad,row = <2>;
 		keypad,column = <2>;
 		linux,code = <KEY_VOLUMEDOWN>;
@@ -326,6 +329,11 @@
 	status = "okay";
 };
 
+&rtc {
+	clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sdhci0 {
 	bus-width = <4>;
 	non-removable;
@@ -382,9 +390,9 @@
 };
 
 &pinctrl0 {
-	t_flash_detect: t-flash-detect {
+	t_flash_detect: t-flash-detect-pins {
 		samsung,pins = "gph3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 };
diff --git a/arch/arm/boot/dts/samsung/s5pv210-aries.dtsi b/arch/arm/boot/dts/samsung/s5pv210-aries.dtsi
new file mode 100644
index 000000000000..f628d3660493
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/s5pv210-aries.dtsi
@@ -0,0 +1,916 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's S5PV210 based Galaxy Aries board device tree source
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "s5pv210.dtsi"
+
+/ {
+	compatible = "samsung,aries", "samsung,s5pv210";
+
+	aliases: aliases {
+		i2c4 = &i2c_sound;
+		i2c5 = &i2c_accel;
+		i2c6 = &i2c_pmic;
+		i2c7 = &i2c_musb;
+		i2c9 = &i2c_fuel;
+		i2c10 = &i2c_touchkey;
+		i2c11 = &i2c_prox;
+		i2c12 = &i2c_magnetometer;
+	};
+
+	memory@30000000 {
+		device_type = "memory";
+		reg = <0x30000000 0x05000000>,
+			<0x40000000 0x10000000>,
+			<0x50000000 0x08000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mfc_left: region@43000000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x43000000 0x2000000>;
+		};
+
+		mfc_right: region@51000000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x51000000 0x2000000>;
+		};
+	};
+
+	pmic_ap_clk: clock-0 {
+		/* Workaround for missing clock on PMIC */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	bt_codec: bt-sco {
+		compatible = "linux,bt-sco";
+		#sound-dai-cells = <0>;
+	};
+
+	vibrator_pwr: regulator-fixed-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vibrator-en";
+		enable-active-high;
+		gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_ena>;
+	};
+
+	touchkey_vdd: regulator-fixed-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VTOUCH_3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchkey_vdd_ena>;
+	};
+
+	gp2a_vled: regulator-fixed-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VLED";
+		enable-active-high;
+		gpio = <&gpj1 4 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gp2a_power>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_gpio_rst>;
+		post-power-on-delay-ms = <500>;
+		power-off-delay-us = <500>;
+	};
+
+	i2c_sound: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sound_i2c_pins>;
+
+		wm8994: audio-codec@1a {
+			compatible = "wlf,wm8994";
+			reg = <0x1a>;
+
+			#sound-dai-cells = <0>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			clocks = <&clocks MOUT_CLKOUT>;
+			clock-names = "MCLK1";
+
+			AVDD2-supply = <&buck3_reg>;
+			DBVDD-supply = <&buck3_reg>;
+			CPVDD-supply = <&buck3_reg>;
+			SPKVDD1-supply = <&buck3_reg>;
+			SPKVDD2-supply = <&buck3_reg>;
+
+			wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100
+					0xa101 0x0100 0x8100 0x0100 0x0100
+					0x0100>;
+
+			wlf,ldo1ena-gpios = <&gpf3 4 GPIO_ACTIVE_HIGH>;
+			wlf,ldo2ena-gpios = <&gpf3 4 GPIO_ACTIVE_HIGH>;
+
+			wlf,lineout1-se;
+			wlf,lineout2-se;
+
+			assigned-clocks = <&clocks MOUT_CLKOUT>;
+			assigned-clock-rates = <0>;
+			assigned-clock-parents = <&xusbxti>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&codec_ldo>;
+		};
+	};
+
+	i2c_accel: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_i2c_pins>;
+
+		accelerometer@38 {
+			compatible = "bosch,bma023";
+			reg = <0x38>;
+
+			vdd-supply = <&ldo9_reg>;
+			vddio-supply = <&ldo9_reg>;
+		};
+	};
+
+	i2c_pmic: i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_i2c_pins>;
+
+		pmic@66 {
+			compatible = "maxim,max8998";
+			reg = <0x66>;
+			interrupt-parent = <&gph0>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+			max8998,pmic-buck1-default-dvs-idx = <1>;
+			max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
+							<&gph0 4 GPIO_ACTIVE_HIGH>;
+			max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
+							<1050000>, <950000>;
+
+			max8998,pmic-buck2-default-dvs-idx = <0>;
+			max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
+			max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pmic_dvs_pins &pmic_irq>;
+
+			regulators {
+				ldo2_reg: LDO2 {
+					regulator-name = "VALIVE_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+
+					regulator-state-mem {
+						regulator-on-in-suspend;
+					};
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VUSB_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VADC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "VTF_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "LDO6";
+					regulator-min-microvolt = <1600000>;
+					regulator-max-microvolt = <3600000>;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VLCD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "VUSB_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "VCC_2.8V_PDA";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "VPLL_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+
+					regulator-state-mem {
+						regulator-on-in-suspend;
+					};
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "CAM_AF_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "CAM_SENSOR_CORE_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "VGA_VDDIO_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "VGA_DVDD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "CAM_ISP_HOST_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "VGA_AVDD_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "VCC_3.0V_LCD";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "vddarm";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1500000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-suspend-microvolt = <1250000>;
+					};
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vddint";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1500000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-suspend-microvolt = <1100000>;
+					};
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "VCC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "CAM_ISP_CORE_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				ap32khz_reg: EN32KHz-AP {
+					regulator-name = "32KHz AP";
+					regulator-always-on;
+				};
+
+				cp32khz_reg: EN32KHz-CP {
+					regulator-name = "32KHz CP";
+				};
+
+				vichg_reg: ENVICHG {
+					regulator-name = "VICHG";
+					regulator-always-on;
+				};
+
+				safe1_sreg: ESAFEOUT1 {
+					regulator-name = "SAFEOUT1";
+				};
+
+				safe2_sreg: ESAFEOUT2 {
+					regulator-name = "SAFEOUT2";
+				};
+			};
+		};
+	};
+
+	i2c_musb: i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&musb_i2c_pins>;
+
+		fsa9480: musb@25 {
+			compatible = "fcs,fsa9480";
+			reg = <0x25>;
+			interrupt-parent = <&gph2>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&musb_irq>;
+		};
+	};
+
+	i2c_fuel: i2c-gpio-4 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fg_i2c_pins>;
+
+		fg: fuelgauge@36 {
+			compatible = "maxim,max17040";
+			reg = <0x36>;
+		};
+	};
+
+	i2c_touchkey: i2c-gpio-5 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchkey_i2c_pins>;
+
+		touchkey@20 {
+			compatible = "cypress,aries-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&touchkey_vdd>;
+			vcc-supply = <&buck3_reg>;
+			linux,keycodes = <KEY_MENU KEY_BACK
+					  KEY_HOMEPAGE KEY_SEARCH>;
+			interrupt-parent = <&gpj4>;
+			interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_irq>;
+		};
+	};
+
+	i2c_prox: i2c-gpio-6 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&prox_i2c_pins>;
+
+		light-sensor@44 {
+			compatible = "sharp,gp2ap002a00f";
+			reg = <0x44>;
+			interrupt-parent = <&gph0>;
+			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+			vdd-supply = <&gp2a_vled>;
+			vio-supply = <&gp2a_vled>;
+			io-channels = <&gp2a_shunt>;
+			io-channel-names = "alsout";
+			sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
+			sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&gp2a_irq>;
+		};
+	};
+
+	i2c_magnetometer: i2c-gpio-7 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&magnetometer_i2c_pins>;
+
+		status = "disabled";
+
+		/* Yamaha yas529 magnetometer, no mainline binding */
+	};
+
+	vibrator: pwm-vibrator {
+		compatible = "pwm-vibrator";
+		pwms = <&pwm 1 44642 0>;
+		pwm-names = "enable";
+		vcc-supply = <&vibrator_pwr>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm1_out>;
+	};
+
+	poweroff: syscon-poweroff {
+		compatible = "syscon-poweroff";
+		regmap = <&pmu_syscon>;
+		offset = <0x681c>; /* PS_HOLD_CONTROL */
+		value = <0x5200>;
+	};
+
+	spi_lcd: spi-2 {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_spi_pins>;
+
+		panel@0 {
+			compatible = "samsung,s6e63m0";
+			reg = <0>;
+			reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
+			vdd3-supply = <&ldo7_reg>;
+			vci-supply = <&ldo17_reg>;
+			spi-max-frequency = <1200000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_rst>;
+
+			port {
+				lcd_ep: endpoint {
+					remote-endpoint = <&fimd_ep>;
+				};
+			};
+		};
+	};
+};
+
+&adc {
+	vdd-supply = <&ldo4_reg>;
+
+	status = "okay";
+
+	gp2a_shunt: current-sense-shunt {
+		compatible = "current-sense-shunt";
+		io-channels = <&adc 9>;
+		shunt-resistor-micro-ohms = <47000000>; /* 47 ohms */
+		#io-channel-cells = <0>;
+	};
+};
+
+&fimd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_clk &lcd_data24>;
+	status = "okay";
+
+	samsung,invert-vden;
+	samsung,invert-vclk;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@3 {
+		reg = <3>;
+		fimd_ep: endpoint {
+			remote-endpoint = <&lcd_ep>;
+		};
+	};
+};
+
+&hsotg {
+	vusb_a-supply = <&ldo8_reg>;
+	vusb_d-supply = <&ldo3_reg>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&i2c2 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <400000>;
+	samsung,i2c-slave-addr = <0x10>;
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		interrupt-parent = <&gpj0>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_irq>;
+		reset-gpios = <&gpj1 3 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2s0 {
+	dmas = <&pdma0 10>, <&pdma0 9>, <&pdma0 11>;
+	status = "okay";
+};
+
+&mfc {
+	memory-region = <&mfc_left>, <&mfc_right>;
+};
+
+&pinctrl0 {
+	bt_reset: bt-reset-pins {
+		samsung,pins = "gpb-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	wlan_bt_en: wlan-bt-en-pins {
+		samsung,pins = "gpb-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-val = <1>;
+	};
+
+	codec_ldo: codec-ldo-pins {
+		samsung,pins = "gpf3-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+	};
+
+	prox_i2c_pins: gp2a-i2c-pins {
+		samsung,pins = "gpg0-2", "gpg2-2";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	wlan_gpio_rst: wlan-gpio-rst-pins {
+		samsung,pins = "gpg1-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+	};
+
+	bt_wake: bt-wake-pins {
+		samsung,pins = "gpg3-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+	};
+
+	gp2a_irq: gp2a-irq-pins {
+		samsung,pins = "gph0-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pmic_dvs_pins: pmic-dvs-pins {
+		samsung,pins = "gph0-3", "gph0-4", "gph0-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+		samsung,pin-val = <0>;
+	};
+
+	pmic_irq: pmic-irq-pins {
+		samsung,pins = "gph0-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	wifi_host_wake: wifi-host-wake-pins {
+		samsung,pins = "gph2-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	bt_host_wake: bt-host-wake-pins {
+		samsung,pins = "gph2-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	musb_irq: musq-irq-pins {
+		samsung,pins = "gph2-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	tf_detect: tf-detect-pins {
+		samsung,pins = "gph3-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	wifi_wake: wifi-wake-pins {
+		samsung,pins = "gph3-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+	};
+
+	magnetometer_i2c_pins: yas529-i2c-pins {
+		samsung,pins = "gpj0-0", "gpj0-1";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	ts_irq: ts-irq-pins {
+		samsung,pins = "gpj0-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	vibrator_ena: vibrator-ena-pins {
+		samsung,pins = "gpj1-1";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	gp2a_power: gp2a-power-pins {
+		samsung,pins = "gpj1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	touchkey_i2c_pins: touchkey-i2c-pins {
+		samsung,pins = "gpj3-0", "gpj3-1";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	touchkey_vdd_ena: touchkey-vdd-ena-pins {
+		samsung,pins = "gpj3-2";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	musb_i2c_pins: musb-i2c-pins {
+		samsung,pins = "gpj3-4", "gpj3-5";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	accel_i2c_pins: accel-i2c-pins {
+		samsung,pins = "gpj3-6", "gpj3-7";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pmic_i2c_pins: pmic-i2c-pins {
+		samsung,pins = "gpj4-0", "gpj4-3";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	touchkey_irq: touchkey-irq-pins {
+		samsung,pins = "gpj4-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	lcd_spi_pins: spi-lcd-pins {
+		samsung,pins = "mp01-1", "mp04-1", "mp04-3";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	fg_i2c_pins: fg-i2c-pins {
+		samsung,pins = "mp05-0", "mp05-1";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	sound_i2c_pins: sound-i2c-pins {
+		samsung,pins = "mp05-2", "mp05-3";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	panel_rst: panel-rst-pins {
+		samsung,pins = "mp05-5";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+};
+
+&pwm {
+	samsung,pwm-outputs = <1>;
+};
+
+&rtc {
+	clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&sdhci1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	max-frequency = <38400000>;
+	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
+	pinctrl-names = "default";
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	status = "okay";
+
+	assigned-clocks = <&clocks MOUT_MMC1>, <&clocks SCLK_MMC1>;
+	assigned-clock-rates = <0>, <50000000>;
+	assigned-clock-parents = <&clocks MOUT_MPLL>;
+
+	wlan@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&gph2>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&ldo5_reg>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	assigned-clocks = <&clocks MOUT_MMC2>, <&clocks SCLK_MMC2>;
+	assigned-clock-rates = <0>, <50000000>;
+	assigned-clock-parents = <&clocks MOUT_MPLL>;
+};
+
+&uart0 {
+	assigned-clocks = <&clocks MOUT_UART0>, <&clocks SCLK_UART0>;
+	assigned-clock-rates = <0>, <111166667>;
+	assigned-clock-parents = <&clocks MOUT_MPLL>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4329-bt";
+		max-speed = <3000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake
+			     &bt_reset &bt_wake>;
+		shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gph2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wakeup";
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+	vbus-supply = <&safe1_sreg>;
+};
+
+&xusbxti {
+	clock-frequency = <24000000>;
+};
diff --git a/arch/arm/boot/dts/samsung/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/samsung/s5pv210-fascinate4g.dts
new file mode 100644
index 000000000000..149e488f8e74
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/s5pv210-fascinate4g.dts
@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "s5pv210-aries.dtsi"
+
+/ {
+	model = "Samsung Galaxy S Fascinate 4G (SGH-T959P) based on S5PV210";
+	compatible = "samsung,fascinate4g", "samsung,aries", "samsung,s5pv210";
+	chassis-type = "handset";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "power";
+			gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-vol-down {
+			label = "volume_down";
+			gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-vol-up {
+			label = "volume_up";
+			gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	headset_micbias_reg: regulator-fixed-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "Headset_Micbias";
+		gpio = <&gpj2 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&headset_micbias_ena>;
+	};
+
+	main_micbias_reg: regulator-fixed-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "Main_Micbias";
+		gpio = <&gpj4 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&main_micbias_ena>;
+	};
+
+	sound {
+		compatible = "samsung,fascinate4g-wm8994";
+
+		model = "Fascinate4G";
+
+		extcon = <&fsa9480>;
+
+		main-micbias-supply = <&main_micbias_reg>;
+		headset-micbias-supply = <&headset_micbias_reg>;
+
+		earpath-sel-gpios = <&gpj2 6 GPIO_ACTIVE_HIGH>;
+
+		io-channels = <&adc 3>;
+		io-channel-names = "headset-detect";
+		headset-detect-gpios = <&gph0 6 GPIO_ACTIVE_HIGH>;
+		headset-key-gpios = <&gph3 6 GPIO_ACTIVE_HIGH>;
+
+		audio-routing = "HP", "HPOUT1L",
+				"HP", "HPOUT1R",
+
+				"SPK", "SPKOUTLN",
+				"SPK", "SPKOUTLP",
+
+				"RCV", "HPOUT2N",
+				"RCV", "HPOUT2P",
+
+				"LINE", "LINEOUT2N",
+				"LINE", "LINEOUT2P",
+
+				"IN1LP", "Main Mic",
+				"IN1LN", "Main Mic",
+
+				"IN1RP", "Headset Mic",
+				"IN1RN", "Headset Mic",
+
+				"Modem Out", "Modem TX",
+				"Modem RX", "Modem In",
+
+				"Bluetooth SPK", "TX",
+				"RX", "Bluetooth Mic";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&headset_det &earpath_sel>;
+
+		cpu {
+			sound-dai = <&i2s0>, <&bt_codec>;
+		};
+
+		codec {
+			sound-dai = <&wm8994>;
+		};
+	};
+};
+
+&fg {
+	compatible = "maxim,max77836-battery";
+
+	interrupt-parent = <&gph3>;
+	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&fg_irq>;
+};
+
+&pinctrl0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep_cfg>;
+
+	headset_det: headset-det-pins {
+		samsung,pins = "gph0-6", "gph3-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+	};
+
+	fg_irq: fg-irq-pins {
+		samsung,pins = "gph3-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	headset_micbias_ena: headset-micbias-ena-pins {
+		samsung,pins = "gpj2-5";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	earpath_sel: earpath-sel-pins {
+		samsung,pins = "gpj2-6";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	main_micbias_ena: main-micbias-ena-pins {
+		samsung,pins = "gpj4-2";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	/* Based on vendor kernel v2.6.35.7 */
+	sleep_cfg: sleep-state {
+		PIN_SLP(gpa0-0, PREV, NONE);
+		PIN_SLP(gpa0-1, PREV, NONE);
+		PIN_SLP(gpa0-2, PREV, NONE);
+		PIN_SLP(gpa0-3, OUT1, NONE);
+		PIN_SLP(gpa0-4, PREV, NONE);
+		PIN_SLP(gpa0-5, PREV, NONE);
+		PIN_SLP(gpa0-6, PREV, NONE);
+		PIN_SLP(gpa0-7, PREV, NONE);
+
+		PIN_SLP(gpa1-0, INPUT, DOWN);
+		PIN_SLP(gpa1-1, OUT0, NONE);
+		PIN_SLP(gpa1-2, INPUT, DOWN);
+		PIN_SLP(gpa1-3, OUT0, NONE);
+
+		PIN_SLP(gpb-0, OUT0, NONE);
+		PIN_SLP(gpb-1, OUT1, NONE);
+		PIN_SLP(gpb-2, OUT0, NONE);
+		PIN_SLP(gpb-3, PREV, NONE);
+		PIN_SLP(gpb-4, INPUT, NONE);
+		PIN_SLP(gpb-5, PREV, NONE);
+		PIN_SLP(gpb-6, INPUT, DOWN);
+		PIN_SLP(gpb-7, OUT0, NONE);
+
+		PIN_SLP(gpc0-0, OUT0, NONE);
+		PIN_SLP(gpc0-1, INPUT, DOWN);
+		PIN_SLP(gpc0-2, OUT0, NONE);
+		PIN_SLP(gpc0-3, INPUT, DOWN);
+		PIN_SLP(gpc0-4, OUT0, NONE);
+
+		PIN_SLP(gpc1-0, INPUT, DOWN);
+		PIN_SLP(gpc1-1, INPUT, DOWN);
+		PIN_SLP(gpc1-2, INPUT, DOWN);
+		PIN_SLP(gpc1-3, INPUT, DOWN);
+		PIN_SLP(gpc1-4, INPUT, DOWN);
+
+		PIN_SLP(gpd0-0, INPUT, DOWN);
+		PIN_SLP(gpd0-1, OUT0, NONE);
+		PIN_SLP(gpd0-2, INPUT, DOWN);
+		PIN_SLP(gpd0-3, INPUT, DOWN);
+
+		PIN_SLP(gpd1-0, INPUT, NONE);
+		PIN_SLP(gpd1-1, INPUT, NONE);
+		PIN_SLP(gpd1-2, INPUT, DOWN);
+		PIN_SLP(gpd1-3, INPUT, DOWN);
+		PIN_SLP(gpd1-4, INPUT, DOWN);
+		PIN_SLP(gpd1-5, INPUT, DOWN);
+
+		PIN_SLP(gpe0-0, INPUT, DOWN);
+		PIN_SLP(gpe0-1, INPUT, DOWN);
+		PIN_SLP(gpe0-2, INPUT, DOWN);
+		PIN_SLP(gpe0-3, INPUT, DOWN);
+		PIN_SLP(gpe0-4, INPUT, DOWN);
+		PIN_SLP(gpe0-5, INPUT, DOWN);
+		PIN_SLP(gpe0-6, INPUT, DOWN);
+		PIN_SLP(gpe0-7, INPUT, DOWN);
+
+		PIN_SLP(gpe1-0, INPUT, DOWN);
+		PIN_SLP(gpe1-1, INPUT, DOWN);
+		PIN_SLP(gpe1-2, INPUT, DOWN);
+		PIN_SLP(gpe1-3, OUT0, NONE);
+		PIN_SLP(gpe1-4, INPUT, DOWN);
+
+		PIN_SLP(gpf0-0, OUT0, NONE);
+		PIN_SLP(gpf0-1, OUT0, NONE);
+		PIN_SLP(gpf0-2, OUT0, NONE);
+		PIN_SLP(gpf0-3, OUT0, NONE);
+		PIN_SLP(gpf0-4, OUT0, NONE);
+		PIN_SLP(gpf0-5, OUT0, NONE);
+		PIN_SLP(gpf0-6, OUT0, NONE);
+		PIN_SLP(gpf0-7, OUT0, NONE);
+
+		PIN_SLP(gpf1-0, OUT0, NONE);
+		PIN_SLP(gpf1-1, OUT0, NONE);
+		PIN_SLP(gpf1-2, OUT0, NONE);
+		PIN_SLP(gpf1-3, OUT0, NONE);
+		PIN_SLP(gpf1-4, OUT0, NONE);
+		PIN_SLP(gpf1-5, OUT0, NONE);
+		PIN_SLP(gpf1-6, OUT0, NONE);
+		PIN_SLP(gpf1-7, OUT0, NONE);
+
+		PIN_SLP(gpf2-0, OUT0, NONE);
+		PIN_SLP(gpf2-1, OUT0, NONE);
+		PIN_SLP(gpf2-2, OUT0, NONE);
+		PIN_SLP(gpf2-3, OUT0, NONE);
+		PIN_SLP(gpf2-4, OUT0, NONE);
+		PIN_SLP(gpf2-5, OUT0, NONE);
+		PIN_SLP(gpf2-6, OUT0, NONE);
+		PIN_SLP(gpf2-7, OUT0, NONE);
+
+		PIN_SLP(gpf3-0, OUT0, NONE);
+		PIN_SLP(gpf3-1, OUT0, NONE);
+		PIN_SLP(gpf3-2, OUT0, NONE);
+		PIN_SLP(gpf3-3, OUT0, NONE);
+		PIN_SLP(gpf3-4, PREV, NONE);
+		PIN_SLP(gpf3-5, INPUT, DOWN);
+
+		PIN_SLP(gpg0-0, INPUT, DOWN);
+		PIN_SLP(gpg0-1, INPUT, DOWN);
+		PIN_SLP(gpg0-2, INPUT, NONE);
+		PIN_SLP(gpg0-3, INPUT, DOWN);
+		PIN_SLP(gpg0-4, INPUT, DOWN);
+		PIN_SLP(gpg0-5, INPUT, DOWN);
+		PIN_SLP(gpg0-6, INPUT, DOWN);
+
+		PIN_SLP(gpg1-0, OUT0, NONE);
+		PIN_SLP(gpg1-1, OUT1, NONE);
+		PIN_SLP(gpg1-2, PREV, NONE);
+		PIN_SLP(gpg1-3, OUT1, NONE);
+		PIN_SLP(gpg1-4, OUT1, NONE);
+		PIN_SLP(gpg1-5, OUT1, NONE);
+		PIN_SLP(gpg1-6, OUT1, NONE);
+
+		PIN_SLP(gpg2-0, OUT0, NONE);
+		PIN_SLP(gpg2-1, OUT0, NONE);
+		PIN_SLP(gpg2-2, INPUT, NONE);
+		PIN_SLP(gpg2-3, OUT0, NONE);
+		PIN_SLP(gpg2-4, OUT0, NONE);
+		PIN_SLP(gpg2-5, OUT0, NONE);
+		PIN_SLP(gpg2-6, OUT0, NONE);
+
+		PIN_SLP(gpg3-0, PREV, UP);
+		PIN_SLP(gpg3-1, PREV, UP);
+		PIN_SLP(gpg3-2, INPUT, NONE);
+		PIN_SLP(gpg3-3, INPUT, DOWN);
+		PIN_SLP(gpg3-4, OUT0, NONE);
+		PIN_SLP(gpg3-5, OUT0, NONE);
+		PIN_SLP(gpg3-6, INPUT, DOWN);
+
+		PIN_SLP(gpi-0, PREV, NONE);
+		PIN_SLP(gpi-1, INPUT, DOWN);
+		PIN_SLP(gpi-2, PREV, NONE);
+		PIN_SLP(gpi-3, PREV, NONE);
+		PIN_SLP(gpi-4, PREV, NONE);
+		PIN_SLP(gpi-5, INPUT, DOWN);
+		PIN_SLP(gpi-6, INPUT, DOWN);
+
+		PIN_SLP(gpj0-0, INPUT, NONE);
+		PIN_SLP(gpj0-1, INPUT, NONE);
+		PIN_SLP(gpj0-2, INPUT, NONE);
+		PIN_SLP(gpj0-3, INPUT, NONE);
+		PIN_SLP(gpj0-4, INPUT, NONE);
+		PIN_SLP(gpj0-5, INPUT, DOWN);
+		PIN_SLP(gpj0-6, OUT0, NONE);
+		PIN_SLP(gpj0-7, INPUT, NONE);
+
+		PIN_SLP(gpj1-0, OUT1, NONE);
+		PIN_SLP(gpj1-1, OUT0, NONE);
+		PIN_SLP(gpj1-2, INPUT, DOWN);
+		PIN_SLP(gpj1-3, PREV, NONE);
+		PIN_SLP(gpj1-4, PREV, NONE);
+		PIN_SLP(gpj1-5, OUT0, NONE);
+
+		PIN_SLP(gpj2-0, INPUT, DOWN);
+		PIN_SLP(gpj2-1, INPUT, DOWN);
+		PIN_SLP(gpj2-2, OUT0, NONE);
+		PIN_SLP(gpj2-3, INPUT, DOWN);
+		PIN_SLP(gpj2-4, INPUT, DOWN);
+		PIN_SLP(gpj2-5, PREV, NONE);
+		PIN_SLP(gpj2-6, PREV, NONE);
+		PIN_SLP(gpj2-7, INPUT, DOWN);
+
+		PIN_SLP(gpj3-0, INPUT, NONE);
+		PIN_SLP(gpj3-1, INPUT, NONE);
+		PIN_SLP(gpj3-2, OUT0, NONE);
+		PIN_SLP(gpj3-3, INPUT, DOWN);
+		PIN_SLP(gpj3-4, INPUT, NONE);
+		PIN_SLP(gpj3-5, INPUT, NONE);
+		PIN_SLP(gpj3-6, INPUT, NONE);
+		PIN_SLP(gpj3-7, INPUT, NONE);
+
+		PIN_SLP(gpj4-0, INPUT, NONE);
+		PIN_SLP(gpj4-1, INPUT, DOWN);
+		PIN_SLP(gpj4-2, PREV, NONE);
+		PIN_SLP(gpj4-3, INPUT, NONE);
+		PIN_SLP(gpj4-4, INPUT, DOWN);
+
+		PIN_SLP(mp01-0, OUT1, NONE);
+		PIN_SLP(mp01-1, OUT0, NONE);
+		PIN_SLP(mp01-2, INPUT, DOWN);
+		PIN_SLP(mp01-3, INPUT, DOWN);
+		PIN_SLP(mp01-4, OUT1, NONE);
+		PIN_SLP(mp01-5, INPUT, DOWN);
+		PIN_SLP(mp01-6, INPUT, DOWN);
+		PIN_SLP(mp01-7, INPUT, DOWN);
+
+		PIN_SLP(mp02-0, INPUT, DOWN);
+		PIN_SLP(mp02-1, INPUT, DOWN);
+		PIN_SLP(mp02-2, INPUT, NONE);
+		PIN_SLP(mp02-3, INPUT, DOWN);
+
+		PIN_SLP(mp03-0, INPUT, DOWN);
+		PIN_SLP(mp03-1, INPUT, DOWN);
+		PIN_SLP(mp03-2, OUT1, NONE);
+		PIN_SLP(mp03-3, OUT0, NONE);
+		PIN_SLP(mp03-4, INPUT, NONE);
+		PIN_SLP(mp03-5, OUT0, NONE);
+		PIN_SLP(mp03-6, INPUT, DOWN);
+		PIN_SLP(mp03-7, INPUT, DOWN);
+
+		PIN_SLP(mp04-0, INPUT, DOWN);
+		PIN_SLP(mp04-1, OUT0, NONE);
+		PIN_SLP(mp04-2, INPUT, DOWN);
+		PIN_SLP(mp04-3, OUT0, NONE);
+		PIN_SLP(mp04-4, INPUT, DOWN);
+		PIN_SLP(mp04-5, INPUT, DOWN);
+		PIN_SLP(mp04-6, OUT0, NONE);
+		PIN_SLP(mp04-7, INPUT, DOWN);
+
+		PIN_SLP(mp05-0, INPUT, NONE);
+		PIN_SLP(mp05-1, INPUT, NONE);
+		PIN_SLP(mp05-2, INPUT, NONE);
+		PIN_SLP(mp05-3, INPUT, NONE);
+		PIN_SLP(mp05-4, INPUT, DOWN);
+		PIN_SLP(mp05-5, OUT0, NONE);
+		PIN_SLP(mp05-6, INPUT, DOWN);
+		PIN_SLP(mp05-7, PREV, NONE);
+
+		PIN_SLP(mp06-0, INPUT, DOWN);
+		PIN_SLP(mp06-1, INPUT, DOWN);
+		PIN_SLP(mp06-2, INPUT, DOWN);
+		PIN_SLP(mp06-3, INPUT, DOWN);
+		PIN_SLP(mp06-4, INPUT, DOWN);
+		PIN_SLP(mp06-5, INPUT, DOWN);
+		PIN_SLP(mp06-6, INPUT, DOWN);
+		PIN_SLP(mp06-7, INPUT, DOWN);
+
+		PIN_SLP(mp07-0, INPUT, DOWN);
+		PIN_SLP(mp07-1, INPUT, DOWN);
+		PIN_SLP(mp07-2, INPUT, DOWN);
+		PIN_SLP(mp07-3, INPUT, DOWN);
+		PIN_SLP(mp07-4, INPUT, DOWN);
+		PIN_SLP(mp07-5, INPUT, DOWN);
+		PIN_SLP(mp07-6, INPUT, DOWN);
+		PIN_SLP(mp07-7, INPUT, DOWN);
+	};
+};
+
+&wm8994 {
+	/* GPIO3 (BCLK2) and GPIO4 (LRCLK2) as outputs */
+	wlf,gpio-cfg = <0xa101 0x8100 0x8100 0x8100 0x8100 0xa101
+			0x0100 0x8100 0x0100 0x0100 0x0100>;
+};
diff --git a/arch/arm/boot/dts/samsung/s5pv210-galaxys.dts b/arch/arm/boot/dts/samsung/s5pv210-galaxys.dts
new file mode 100644
index 000000000000..879294412381
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/s5pv210-galaxys.dts
@@ -0,0 +1,447 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "s5pv210-aries.dtsi"
+
+/ {
+	model = "Samsung Galaxy S1 (GT-I9000) based on S5PV210";
+	compatible = "samsung,galaxys", "samsung,aries", "samsung,s5pv210";
+	chassis-type = "handset";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	nand_pwrseq: nand-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpj2 7 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&massmemory_en>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "power";
+			gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-vol-down {
+			label = "volume_down";
+			gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-vol-up {
+			label = "volume_up";
+			gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-home {
+			label = "home";
+			gpios = <&gph3 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+			wakeup-source;
+		};
+	};
+
+	i2c_fmradio: i2c-gpio-8 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpd1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpd1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fm_i2c_pins>;
+
+		fmradio@10 {
+			compatible = "silabs,si470x";
+			reg = <0x10>;
+			interrupt-parent = <&gpj2>;
+			interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpj2 5 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&fm_irq &fm_rst>;
+		};
+	};
+
+	micbias_reg: regulator-fixed-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MICBIAS";
+		gpio = <&gpj4 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&micbias_reg_ena>;
+	};
+
+	sound {
+		compatible = "samsung,aries-wm8994";
+
+		model = "Aries";
+
+		extcon = <&fsa9480>;
+
+		main-micbias-supply = <&micbias_reg>;
+		headset-micbias-supply = <&micbias_reg>;
+
+		earpath-sel-gpios = <&gpj2 6 GPIO_ACTIVE_HIGH>;
+
+		io-channels = <&adc 3>;
+		io-channel-names = "headset-detect";
+		headset-detect-gpios = <&gph0 6 GPIO_ACTIVE_LOW>;
+		headset-key-gpios = <&gph3 6 GPIO_ACTIVE_HIGH>;
+
+		audio-routing = "HP", "HPOUT1L",
+				"HP", "HPOUT1R",
+
+				"SPK", "SPKOUTLN",
+				"SPK", "SPKOUTLP",
+
+				"RCV", "HPOUT2N",
+				"RCV", "HPOUT2P",
+
+				"LINE", "LINEOUT2N",
+				"LINE", "LINEOUT2P",
+
+				"IN1LP", "Main Mic",
+				"IN1LN", "Main Mic",
+
+				"IN1RP", "Headset Mic",
+				"IN1RN", "Headset Mic",
+
+				"IN2LN", "FM In",
+				"IN2RN", "FM In",
+
+				"Modem Out", "Modem TX",
+				"Modem RX", "Modem In",
+
+				"Bluetooth SPK", "TX",
+				"RX", "Bluetooth Mic";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&headset_det &earpath_sel>;
+
+		cpu {
+			sound-dai = <&i2s0>, <&bt_codec>;
+		};
+
+		codec {
+			sound-dai = <&wm8994>;
+		};
+	};
+};
+
+&aliases {
+	i2c8 = &i2c_fmradio;
+};
+
+&pinctrl0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep_cfg>;
+
+	fm_i2c_pins: fm-i2c-pins {
+		samsung,pins = "gpd1-2", "gpd1-3";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	headset_det: headset-det-pins {
+		samsung,pins = "gph0-6", "gph3-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+	};
+
+	fm_irq: fm-irq-pins {
+		samsung,pins = "gpj2-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	fm_rst: fm-rst-pins {
+		samsung,pins = "gpj2-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	earpath_sel: earpath-sel-pins {
+		samsung,pins = "gpj2-6";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	massmemory_en: massmemory-en-pins {
+		samsung,pins = "gpj2-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	micbias_reg_ena: micbias-reg-ena-pins {
+		samsung,pins = "gpj4-2";
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	/* Based on CyanogenMod 3.0.101 kernel */
+	sleep_cfg: sleep-state {
+		PIN_SLP(gpa0-0, PREV, NONE);
+		PIN_SLP(gpa0-1, PREV, NONE);
+		PIN_SLP(gpa0-2, PREV, NONE);
+		PIN_SLP(gpa0-3, OUT1, NONE);
+		PIN_SLP(gpa0-4, INPUT, DOWN);
+		PIN_SLP(gpa0-5, OUT0, NONE);
+		PIN_SLP(gpa0-6, INPUT, DOWN);
+		PIN_SLP(gpa0-7, OUT1, NONE);
+
+		PIN_SLP(gpa1-0, INPUT, DOWN);
+		PIN_SLP(gpa1-1, OUT0, NONE);
+		PIN_SLP(gpa1-2, INPUT, NONE);
+		PIN_SLP(gpa1-3, OUT0, NONE);
+
+		PIN_SLP(gpb-0, OUT0, NONE);
+		PIN_SLP(gpb-1, OUT1, NONE);
+		PIN_SLP(gpb-2, OUT0, NONE);
+		PIN_SLP(gpb-3, PREV, NONE);
+		PIN_SLP(gpb-4, INPUT, NONE);
+		PIN_SLP(gpb-5, PREV, NONE);
+		PIN_SLP(gpb-6, INPUT, DOWN);
+		PIN_SLP(gpb-7, OUT0, NONE);
+
+		PIN_SLP(gpc0-0, OUT0, NONE);
+		PIN_SLP(gpc0-1, INPUT, DOWN);
+		PIN_SLP(gpc0-2, OUT0, NONE);
+		PIN_SLP(gpc0-3, INPUT, NONE);
+		PIN_SLP(gpc0-4, OUT0, NONE);
+
+		PIN_SLP(gpc1-0, INPUT, DOWN);
+		PIN_SLP(gpc1-1, INPUT, DOWN);
+		PIN_SLP(gpc1-2, INPUT, DOWN);
+		PIN_SLP(gpc1-3, INPUT, DOWN);
+		PIN_SLP(gpc1-4, INPUT, DOWN);
+
+		PIN_SLP(gpd0-0, INPUT, DOWN);
+		PIN_SLP(gpd0-1, OUT0, NONE);
+		PIN_SLP(gpd0-2, INPUT, DOWN);
+		PIN_SLP(gpd0-3, INPUT, DOWN);
+
+		PIN_SLP(gpd1-0, INPUT, NONE);
+		PIN_SLP(gpd1-1, INPUT, NONE);
+		PIN_SLP(gpd1-2, INPUT, NONE);
+		PIN_SLP(gpd1-3, INPUT, NONE);
+		PIN_SLP(gpd1-4, INPUT, DOWN);
+		PIN_SLP(gpd1-5, INPUT, DOWN);
+
+		PIN_SLP(gpe0-0, INPUT, DOWN);
+		PIN_SLP(gpe0-1, INPUT, DOWN);
+		PIN_SLP(gpe0-2, INPUT, DOWN);
+		PIN_SLP(gpe0-3, INPUT, DOWN);
+		PIN_SLP(gpe0-4, INPUT, DOWN);
+		PIN_SLP(gpe0-5, INPUT, DOWN);
+		PIN_SLP(gpe0-6, INPUT, DOWN);
+		PIN_SLP(gpe0-7, INPUT, DOWN);
+
+		PIN_SLP(gpe1-0, INPUT, DOWN);
+		PIN_SLP(gpe1-1, INPUT, DOWN);
+		PIN_SLP(gpe1-2, INPUT, DOWN);
+		PIN_SLP(gpe1-3, OUT0, NONE);
+		PIN_SLP(gpe1-4, INPUT, DOWN);
+
+		PIN_SLP(gpf0-0, OUT0, NONE);
+		PIN_SLP(gpf0-1, OUT0, NONE);
+		PIN_SLP(gpf0-2, OUT0, NONE);
+		PIN_SLP(gpf0-3, OUT0, NONE);
+		PIN_SLP(gpf0-4, OUT0, NONE);
+		PIN_SLP(gpf0-5, OUT0, NONE);
+		PIN_SLP(gpf0-6, OUT0, NONE);
+		PIN_SLP(gpf0-7, OUT0, NONE);
+
+		PIN_SLP(gpf1-0, OUT0, NONE);
+		PIN_SLP(gpf1-1, OUT0, NONE);
+		PIN_SLP(gpf1-2, OUT0, NONE);
+		PIN_SLP(gpf1-3, OUT0, NONE);
+		PIN_SLP(gpf1-4, OUT0, NONE);
+		PIN_SLP(gpf1-5, OUT0, NONE);
+		PIN_SLP(gpf1-6, OUT0, NONE);
+		PIN_SLP(gpf1-7, OUT0, NONE);
+
+		PIN_SLP(gpf2-0, OUT0, NONE);
+		PIN_SLP(gpf2-1, OUT0, NONE);
+		PIN_SLP(gpf2-2, OUT0, NONE);
+		PIN_SLP(gpf2-3, OUT0, NONE);
+		PIN_SLP(gpf2-4, OUT0, NONE);
+		PIN_SLP(gpf2-5, OUT0, NONE);
+		PIN_SLP(gpf2-6, OUT0, NONE);
+		PIN_SLP(gpf2-7, OUT0, NONE);
+
+		PIN_SLP(gpf3-0, OUT0, NONE);
+		PIN_SLP(gpf3-1, OUT0, NONE);
+		PIN_SLP(gpf3-2, OUT0, NONE);
+		PIN_SLP(gpf3-3, OUT0, NONE);
+		PIN_SLP(gpf3-4, PREV, NONE);
+		PIN_SLP(gpf3-5, INPUT, DOWN);
+
+		PIN_SLP(gpg0-0, OUT0, NONE);
+		PIN_SLP(gpg0-1, INPUT, NONE);
+		PIN_SLP(gpg0-2, INPUT, NONE);
+		PIN_SLP(gpg0-3, INPUT, NONE);
+		PIN_SLP(gpg0-4, INPUT, NONE);
+		PIN_SLP(gpg0-5, INPUT, NONE);
+		PIN_SLP(gpg0-6, INPUT, NONE);
+
+		PIN_SLP(gpg1-0, OUT0, NONE);
+		PIN_SLP(gpg1-1, OUT1, NONE);
+		PIN_SLP(gpg1-2, PREV, NONE);
+		PIN_SLP(gpg1-3, OUT1, NONE);
+		PIN_SLP(gpg1-4, OUT1, NONE);
+		PIN_SLP(gpg1-5, OUT1, NONE);
+		PIN_SLP(gpg1-6, OUT1, NONE);
+
+		PIN_SLP(gpg2-0, OUT0, NONE);
+		PIN_SLP(gpg2-1, OUT0, NONE);
+		PIN_SLP(gpg2-2, INPUT, NONE);
+		PIN_SLP(gpg2-3, OUT0, NONE);
+		PIN_SLP(gpg2-4, OUT0, NONE);
+		PIN_SLP(gpg2-5, OUT0, NONE);
+		PIN_SLP(gpg2-6, OUT0, NONE);
+
+		PIN_SLP(gpg3-0, OUT1, NONE);
+		PIN_SLP(gpg3-1, OUT0, NONE);
+		PIN_SLP(gpg3-2, INPUT, NONE);
+		PIN_SLP(gpg3-3, INPUT, DOWN);
+		PIN_SLP(gpg3-4, OUT0, NONE);
+		PIN_SLP(gpg3-5, OUT0, NONE);
+		PIN_SLP(gpg3-6, INPUT, DOWN);
+
+		PIN_SLP(gpi-0, PREV, NONE);
+		PIN_SLP(gpi-1, INPUT, DOWN);
+		PIN_SLP(gpi-2, PREV, NONE);
+		PIN_SLP(gpi-3, PREV, NONE);
+		PIN_SLP(gpi-4, PREV, NONE);
+		PIN_SLP(gpi-5, INPUT, DOWN);
+		PIN_SLP(gpi-6, INPUT, DOWN);
+
+		PIN_SLP(gpj0-0, INPUT, NONE);
+		PIN_SLP(gpj0-1, INPUT, NONE);
+		PIN_SLP(gpj0-2, INPUT, NONE);
+		PIN_SLP(gpj0-3, INPUT, NONE);
+		PIN_SLP(gpj0-4, INPUT, NONE);
+		PIN_SLP(gpj0-5, INPUT, DOWN);
+		PIN_SLP(gpj0-6, OUT0, NONE);
+		PIN_SLP(gpj0-7, INPUT, NONE);
+
+		PIN_SLP(gpj1-0, INPUT, DOWN);
+		PIN_SLP(gpj1-1, OUT0, NONE);
+		PIN_SLP(gpj1-2, INPUT, DOWN);
+		PIN_SLP(gpj1-3, PREV, NONE);
+		PIN_SLP(gpj1-4, PREV, NONE);
+		PIN_SLP(gpj1-5, OUT0, NONE);
+
+		PIN_SLP(gpj2-0, INPUT, DOWN);
+		PIN_SLP(gpj2-1, INPUT, DOWN);
+		PIN_SLP(gpj2-2, OUT0, NONE);
+		PIN_SLP(gpj2-3, INPUT, DOWN);
+		PIN_SLP(gpj2-4, INPUT, UP);
+		PIN_SLP(gpj2-5, PREV, NONE);
+		PIN_SLP(gpj2-6, PREV, NONE);
+		PIN_SLP(gpj2-7, OUT1, NONE);
+
+		PIN_SLP(gpj3-0, INPUT, NONE);
+		PIN_SLP(gpj3-1, INPUT, NONE);
+		PIN_SLP(gpj3-2, OUT0, NONE);
+		PIN_SLP(gpj3-3, INPUT, DOWN);
+		PIN_SLP(gpj3-4, INPUT, NONE);
+		PIN_SLP(gpj3-5, INPUT, NONE);
+		PIN_SLP(gpj3-6, INPUT, NONE);
+		PIN_SLP(gpj3-7, INPUT, NONE);
+
+		PIN_SLP(gpj4-0, INPUT, NONE);
+		PIN_SLP(gpj4-1, INPUT, DOWN);
+		PIN_SLP(gpj4-2, PREV, NONE);
+		PIN_SLP(gpj4-3, INPUT, NONE);
+		PIN_SLP(gpj4-4, INPUT, DOWN);
+
+		PIN_SLP(mp01-0, INPUT, DOWN);
+		PIN_SLP(mp01-1, OUT0, NONE);
+		PIN_SLP(mp01-2, INPUT, DOWN);
+		PIN_SLP(mp01-3, INPUT, DOWN);
+		PIN_SLP(mp01-4, OUT1, NONE);
+		PIN_SLP(mp01-5, INPUT, DOWN);
+		PIN_SLP(mp01-6, INPUT, DOWN);
+		PIN_SLP(mp01-7, INPUT, DOWN);
+
+		PIN_SLP(mp02-0, INPUT, DOWN);
+		PIN_SLP(mp02-1, INPUT, DOWN);
+		PIN_SLP(mp02-2, INPUT, NONE);
+		PIN_SLP(mp02-3, INPUT, DOWN);
+
+		PIN_SLP(mp03-0, INPUT, DOWN);
+		PIN_SLP(mp03-1, INPUT, DOWN);
+		PIN_SLP(mp03-2, OUT1, NONE);
+		PIN_SLP(mp03-3, OUT0, NONE);
+		PIN_SLP(mp03-4, INPUT, NONE);
+		PIN_SLP(mp03-5, OUT1, NONE);
+		PIN_SLP(mp03-6, INPUT, DOWN);
+		PIN_SLP(mp03-7, INPUT, DOWN);
+
+		PIN_SLP(mp04-0, INPUT, DOWN);
+		PIN_SLP(mp04-1, OUT0, NONE);
+		PIN_SLP(mp04-2, INPUT, DOWN);
+		PIN_SLP(mp04-3, OUT0, NONE);
+		PIN_SLP(mp04-4, INPUT, DOWN);
+		PIN_SLP(mp04-5, INPUT, DOWN);
+		PIN_SLP(mp04-6, OUT0, NONE);
+		PIN_SLP(mp04-7, INPUT, DOWN);
+
+		PIN_SLP(mp05-0, INPUT, NONE);
+		PIN_SLP(mp05-1, INPUT, NONE);
+		PIN_SLP(mp05-2, INPUT, NONE);
+		PIN_SLP(mp05-3, INPUT, NONE);
+		PIN_SLP(mp05-4, INPUT, DOWN);
+		PIN_SLP(mp05-5, OUT0, NONE);
+		PIN_SLP(mp05-6, INPUT, DOWN);
+		PIN_SLP(mp05-7, PREV, NONE);
+
+		PIN_SLP(mp06-0, INPUT, DOWN);
+		PIN_SLP(mp06-1, INPUT, DOWN);
+		PIN_SLP(mp06-2, INPUT, DOWN);
+		PIN_SLP(mp06-3, INPUT, DOWN);
+		PIN_SLP(mp06-4, INPUT, DOWN);
+		PIN_SLP(mp06-5, INPUT, DOWN);
+		PIN_SLP(mp06-6, INPUT, DOWN);
+		PIN_SLP(mp06-7, INPUT, DOWN);
+
+		PIN_SLP(mp07-0, INPUT, DOWN);
+		PIN_SLP(mp07-1, INPUT, DOWN);
+		PIN_SLP(mp07-2, INPUT, DOWN);
+		PIN_SLP(mp07-3, INPUT, DOWN);
+		PIN_SLP(mp07-4, INPUT, DOWN);
+		PIN_SLP(mp07-5, INPUT, DOWN);
+		PIN_SLP(mp07-6, INPUT, DOWN);
+		PIN_SLP(mp07-7, INPUT, DOWN);
+	};
+};
+
+&sdhci0 {
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&nand_pwrseq>;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	assigned-clocks = <&clocks MOUT_MMC0>, <&clocks SCLK_MMC0>;
+	assigned-clock-rates = <0>, <52000000>;
+	assigned-clock-parents = <&clocks MOUT_MPLL>;
+};
diff --git a/arch/arm/boot/dts/s5pv210-goni.dts b/arch/arm/boot/dts/samsung/s5pv210-goni.dts
index fbbd93707404..d32f42dd1bf5 100644
--- a/arch/arm/boot/dts/s5pv210-goni.dts
+++ b/arch/arm/boot/dts/samsung/s5pv210-goni.dts
@@ -11,6 +11,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include "s5pv210.dtsi"
 
@@ -28,57 +30,54 @@
 
 	memory@30000000 {
 		device_type = "memory";
-		reg = <0x30000000 0x05000000
-			0x40000000 0x10000000
-			0x50000000 0x08000000>;
+		reg = <0x30000000 0x05000000>,
+			<0x40000000 0x10000000>,
+			<0x50000000 0x08000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	pmic_ap_clk: clock-0 {
+		/* Workaround for missing clock on PMIC */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
 
-		vtf_reg: fixed-regulator@0 {
-			compatible = "regulator-fixed";
-			regulator-name = "V_TF_2.8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			reg = <0>;
-			gpio = <&mp05 4 0>;
-			enable-active-high;
-		};
+	vtf_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_TF_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&mp05 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		pda_reg: fixed-regulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "VCC_1.8V_PDA";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			reg = <1>;
-		};
+	pda_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1.8V_PDA";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
 
-		bat_reg: fixed-regulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "V_BAT";
-			regulator-min-microvolt = <3700000>;
-			regulator-max-microvolt = <3700000>;
-			reg = <2>;
-		};
+	bat_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_BAT";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
 
-		tsp_reg: fixed-regulator@3 {
-			compatible = "regulator-fixed";
-			regulator-name = "TSP_VDD";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			reg = <3>;
-			gpio = <&gpj1 3 0>;
-			enable-active-high;
-		};
+	tsp_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_VDD";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpj1 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	i2c_pmic: i2c-pmic {
 		compatible = "i2c-gpio";
-		gpios = <&gpj4 0 0>, /* sda */
-			<&gpj4 3 0>; /* scl */
+		sda-gpios = <&gpj4 0 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpj4 3 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <2>;        /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -88,13 +87,13 @@
 			reg = <0x66>;
 
 			max8998,pmic-buck1-default-dvs-idx = <0>;
-			max8998,pmic-buck1-dvs-gpios = <&gph0 3 0>,
-							<&gph0 4 0>;
+			max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
+							<&gph0 4 GPIO_ACTIVE_HIGH>;
 			max8998,pmic-buck1-dvs-voltage = <1200000>, <1200000>,
 							<1200000>, <1200000>;
 
 			max8998,pmic-buck2-default-dvs-idx = <0>;
-			max8998,pmic-buck2-dvs-gpio = <&gph0 5 0>;
+			max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
 			max8998,pmic-buck2-dvs-voltage = <1200000>, <1200000>;
 
 			regulators {
@@ -224,6 +223,11 @@
 					regulator-max-microvolt = <1200000>;
 					regulator-always-on;
 				};
+
+				ap32khz_reg: EN32KHz-AP {
+					regulator-name = "32KHz AP";
+					regulator-always-on;
+				};
 			};
 		};
 	};
@@ -255,37 +259,37 @@
 			<&keypad_col0>, <&keypad_col1>, <&keypad_col2>;
 	status = "okay";
 
-	key_1 {
+	key-1 {
 		keypad,row = <0>;
 		keypad,column = <1>;
 		linux,code = <KEY_CONNECT>;
 	};
 
-	key_2 {
+	key-2 {
 		keypad,row = <0>;
 		keypad,column = <2>;
 		linux,code = <KEY_BACK>;
 	};
 
-	key_3 {
+	key-3 {
 		keypad,row = <1>;
 		keypad,column = <1>;
 		linux,code = <KEY_CAMERA_FOCUS>;
 	};
 
-	key_4 {
+	key-4 {
 		keypad,row = <1>;
 		keypad,column = <2>;
 		linux,code = <KEY_VOLUMEUP>;
 	};
 
-	key_5 {
+	key-5 {
 		keypad,row = <2>;
 		keypad,column = <1>;
 		linux,code = <KEY_CAMERA>;
 	};
 
-	key_6 {
+	key-6 {
 		keypad,row = <2>;
 		keypad,column = <2>;
 		linux,code = <KEY_VOLUMEDOWN>;
@@ -308,6 +312,11 @@
 	status = "okay";
 };
 
+&rtc {
+	clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
+};
+
 &sdhci0 {
 	bus-width = <4>;
 	non-removable;
@@ -344,20 +353,11 @@
 	samsung,i2c-slave-addr = <0x10>;
 	status = "okay";
 
-	tsp@4a {
+	touchscreen@4a {
 		compatible = "atmel,maxtouch";
 		reg = <0x4a>;
 		interrupt-parent = <&gpj0>;
-		interrupts = <5 2>;
-
-		atmel,x-line = <17>;
-		atmel,y-line = <11>;
-		atmel,x-size = <800>;
-		atmel,y-size = <480>;
-		atmel,burst-length = <0x21>;
-		atmel,threshold = <0x28>;
-		atmel,orientation = <1>;
-
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 		vdd-supply = <&tsp_reg>;
 	};
 };
@@ -378,8 +378,8 @@
 		clock-frequency = <16000000>;
 		clocks = <&camera 0>;
 		clock-names = "mclk";
-		nreset-gpios = <&gpb 2 0>;
-		nstby-gpios = <&gpb 0 0>;
+		nreset-gpios = <&gpb 2 GPIO_ACTIVE_HIGH>;
+		nstby-gpios = <&gpb 0 GPIO_ACTIVE_HIGH>;
 
 		port {
 			noon010pc30_ep: endpoint {
diff --git a/arch/arm/boot/dts/samsung/s5pv210-pinctrl.dtsi b/arch/arm/boot/dts/samsung/s5pv210-pinctrl.dtsi
new file mode 100644
index 000000000000..6ecdd504e5f4
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/s5pv210-pinctrl.dtsi
@@ -0,0 +1,845 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's S5PV210 SoC device tree source - pin control-related
+ * definitions
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Samsung's S5PV210 SoC pin banks, pin-mux and pin-config options are
+ * listed as device tree nodes in this file.
+ */
+
+#include "s5pv210-pinctrl.h"
+
+#define PIN_SLP(_pin, _mode, _pull)					\
+	pin- ## _pin {							\
+		samsung,pins = #_pin;					\
+		samsung,pin-con-pdn = <S5PV210_PIN_PDN_ ##_mode>;	\
+		samsung,pin-pud-pdn = <S5PV210_PIN_PULL_ ##_pull>;	\
+	}
+
+&pinctrl0 {
+	gpa0: gpa0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa1: gpa1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb: gpb-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc0: gpc0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe0: gpe0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe1: gpe1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf0: gpf0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf2: gpf2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf3: gpf3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg0: gpg0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj0: gpj0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj1: gpj1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj2: gpj2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj3: gpj3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj4: gpj4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpi: gpi-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp01: mp01-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp02: mp02-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp03: mp03-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp04: mp04-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp05: mp05-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp06: mp06-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp07: mp07-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gph0: gph0-gpio-bank {
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&vic0>;
+		interrupts = <0>, <1>, <2>, <3>,
+				<4>, <5>, <6>, <7>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+	gph1: gph1-gpio-bank {
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&vic0>;
+		interrupts = <8>, <9>, <10>, <11>,
+				<12>, <13>, <14>, <15>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+	gph2: gph2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gph3: gph3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	uart0_data: uart0-data-pins {
+		samsung,pins = "gpa0-0", "gpa0-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart0_fctl: uart0-fctl-pins {
+		samsung,pins = "gpa0-2", "gpa0-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart1_data: uart1-data-pins {
+		samsung,pins = "gpa0-4", "gpa0-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart1_fctl: uart1-fctl-pins {
+		samsung,pins = "gpa0-6", "gpa0-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart2_data: uart2-data-pins {
+		samsung,pins = "gpa1-0", "gpa1-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart2_fctl: uart2-fctl-pins {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart3_data: uart3-data-pins {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	uart_audio: uart-audio-pins {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	spi0_bus: spi0-bus-pins {
+		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	spi1_bus: spi1-bus-pins {
+		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2s0_bus: i2s0-bus-pins {
+		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
+				"gpi-4", "gpi-5", "gpi-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2s1_bus: i2s1-bus-pins {
+		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+				"gpc0-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2s2_bus: i2s2-bus-pins {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pcm1_bus: pcm1-bus-pins {
+		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+				"gpc0-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	ac97_bus: ac97-bus-pins {
+		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+				"gpc0-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2s2_bus: i2s2-bus-pins {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pcm2_bus: pcm2-bus-pins {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	spdif_bus: spdif-bus-pins {
+		samsung,pins = "gpc1-0", "gpc1-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	spi2_bus: spi2-bus-pins {
+		samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_5>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2c0_bus: i2c0-bus-pins {
+		samsung,pins = "gpd1-0", "gpd1-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2c1_bus: i2c1-bus-pins {
+		samsung,pins = "gpd1-2", "gpd1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	i2c2_bus: i2c2-bus-pins {
+		samsung,pins = "gpd1-4", "gpd1-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pwm0_out: pwm0-out-pins {
+		samsung,pins = "gpd0-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pwm1_out: pwm1-out-pins {
+		samsung,pins = "gpd0-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pwm2_out: pwm2-out-pins {
+		samsung,pins = "gpd0-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	pwm3_out: pwm3-out-pins {
+		samsung,pins = "gpd0-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row0: keypad-row-0-pins {
+		samsung,pins = "gph3-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row1: keypad-row-1-pins {
+		samsung,pins = "gph3-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row2: keypad-row-2-pins {
+		samsung,pins = "gph3-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row3: keypad-row-3-pins {
+		samsung,pins = "gph3-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row4: keypad-row-4-pins {
+		samsung,pins = "gph3-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row5: keypad-row-5-pins {
+		samsung,pins = "gph3-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row6: keypad-row-6-pins {
+		samsung,pins = "gph3-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_row7: keypad-row-7-pins {
+		samsung,pins = "gph3-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col0: keypad-col-0-pins {
+		samsung,pins = "gph2-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col1: keypad-col-1-pins {
+		samsung,pins = "gph2-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col2: keypad-col-2-pins {
+		samsung,pins = "gph2-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col3: keypad-col-3-pins {
+		samsung,pins = "gph2-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col4: keypad-col-4-pins {
+		samsung,pins = "gph2-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col5: keypad-col-5-pins {
+		samsung,pins = "gph2-5";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col6: keypad-col-6-pins {
+		samsung,pins = "gph2-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	keypad_col7: keypad-col-7-pins {
+		samsung,pins = "gph2-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	sd0_clk: sd0-clk-pins {
+		samsung,pins = "gpg0-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd0_cmd: sd0-cmd-pins {
+		samsung,pins = "gpg0-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd0_cd: sd0-cd-pins {
+		samsung,pins = "gpg0-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd0_bus1: sd0-bus-width1-pins {
+		samsung,pins = "gpg0-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd0_bus4: sd0-bus-width4-pins {
+		samsung,pins = "gpg0-3", "gpg0-4", "gpg0-5", "gpg0-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd0_bus8: sd0-bus-width8-pins {
+		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd1_clk: sd1-clk-pins {
+		samsung,pins = "gpg1-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd1_cmd: sd1-cmd-pins {
+		samsung,pins = "gpg1-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd1_cd: sd1-cd-pins {
+		samsung,pins = "gpg1-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd1_bus1: sd1-bus-width1-pins {
+		samsung,pins = "gpg1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd1_bus4: sd1-bus-width4-pins {
+		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd2_clk: sd2-clk-pins {
+		samsung,pins = "gpg2-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd2_cmd: sd2-cmd-pins {
+		samsung,pins = "gpg2-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd2_cd: sd2-cd-pins {
+		samsung,pins = "gpg2-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd2_bus1: sd2-bus-width1-pins {
+		samsung,pins = "gpg2-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd2_bus4: sd2-bus-width4-pins {
+		samsung,pins = "gpg2-3", "gpg2-4", "gpg2-5", "gpg2-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd2_bus8: sd2-bus-width8-pins {
+		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd3_clk: sd3-clk-pins {
+		samsung,pins = "gpg3-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd3_cmd: sd3-cmd-pins {
+		samsung,pins = "gpg3-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd3_cd: sd3-cd-pins {
+		samsung,pins = "gpg3-2";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd3_bus1: sd3-bus-width1-pins {
+		samsung,pins = "gpg3-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	sd3_bus4: sd3-bus-width4-pins {
+		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	eint0: ext-int0-pins {
+		samsung,pins = "gph0-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	eint8: ext-int8-pins {
+		samsung,pins = "gph1-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	eint15: ext-int15-pins {
+		samsung,pins = "gph1-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	eint16: ext-int16-pins {
+		samsung,pins = "gph2-0";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	eint31: ext-int31-pins {
+		samsung,pins = "gph3-7";
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	cam_port_a_io: cam-port-a-io-pins {
+		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+				"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+				"gpe1-0", "gpe1-1", "gpe1-2", "gpe1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	cam_port_a_clk_active: cam-port-a-clk-active-pins {
+		samsung,pins = "gpe1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	cam_port_a_clk_idle: cam-port-a-clk-idle-pins {
+		samsung,pins = "gpe1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	cam_port_b_io: cam-port-b-io-pins {
+		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
+				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
+				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	cam_port_b_clk_active: cam-port-b-clk-active-pins {
+		samsung,pins = "gpj1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
+	};
+
+	cam_port_b_clk_idle: cam-port-b-clk-idle-pins {
+		samsung,pins = "gpj1-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	lcd_ctrl: lcd-ctrl-pins {
+		samsung,pins = "gpd0-0", "gpd0-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	lcd_sync: lcd-sync-pins {
+		samsung,pins = "gpf0-0", "gpf0-1";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	lcd_clk: lcd-clk-pins {
+		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+
+	lcd_data24: lcd-data-width24-pins {
+		samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
+			       "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
+			       "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
+			       "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
+			       "gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7",
+			       "gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
+	};
+};
diff --git a/arch/arm/boot/dts/samsung/s5pv210-pinctrl.h b/arch/arm/boot/dts/samsung/s5pv210-pinctrl.h
new file mode 100644
index 000000000000..29bdf376d8f1
--- /dev/null
+++ b/arch/arm/boot/dts/samsung/s5pv210-pinctrl.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung S5PV210 DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_S5PV210_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_S5PV210_PINCTRL_H__
+
+#define S5PV210_PIN_PULL_NONE		0
+#define S5PV210_PIN_PULL_DOWN		1
+#define S5PV210_PIN_PULL_UP		2
+
+/* Pin function in power down mode */
+#define S5PV210_PIN_PDN_OUT0		0
+#define S5PV210_PIN_PDN_OUT1		1
+#define S5PV210_PIN_PDN_INPUT		2
+#define S5PV210_PIN_PDN_PREV		3
+
+#define S5PV210_PIN_DRV_LV1		0
+#define S5PV210_PIN_DRV_LV2		2
+#define S5PV210_PIN_DRV_LV3		1
+#define S5PV210_PIN_DRV_LV4		3
+
+#define S5PV210_PIN_FUNC_INPUT		0
+#define S5PV210_PIN_FUNC_OUTPUT		1
+#define S5PV210_PIN_FUNC_2		2
+#define S5PV210_PIN_FUNC_3		3
+#define S5PV210_PIN_FUNC_4		4
+#define S5PV210_PIN_FUNC_5		5
+#define S5PV210_PIN_FUNC_6		6
+#define S5PV210_PIN_FUNC_EINT		0xf
+#define S5PV210_PIN_FUNC_F		S5PV210_PIN_FUNC_EINT
+
+#endif /* __DTS_ARM_SAMSUNG_S5PV210_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/s5pv210-smdkc110.dts b/arch/arm/boot/dts/samsung/s5pv210-smdkc110.dts
index e5aec6c526fb..0c623b78af72 100644
--- a/arch/arm/boot/dts/s5pv210-smdkc110.dts
+++ b/arch/arm/boot/dts/samsung/s5pv210-smdkc110.dts
@@ -30,6 +30,13 @@
 		device_type = "memory";
 		reg = <0x20000000 0x20000000>;
 	};
+
+	pmic_ap_clk: clock-0 {
+		/* Workaround for missing PMIC and its clock */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
 };
 
 &xusbxti {
@@ -54,6 +61,8 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &i2c0 {
diff --git a/arch/arm/boot/dts/s5pv210-smdkv210.dts b/arch/arm/boot/dts/samsung/s5pv210-smdkv210.dts
index 84b38f185199..901e7197b136 100644
--- a/arch/arm/boot/dts/s5pv210-smdkv210.dts
+++ b/arch/arm/boot/dts/samsung/s5pv210-smdkv210.dts
@@ -15,6 +15,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include "s5pv210.dtsi"
 
@@ -31,11 +32,18 @@
 		reg = <0x20000000 0x40000000>;
 	};
 
-	ethernet@18000000 {
+	pmic_ap_clk: clock-0 {
+		/* Workaround for missing PMIC and its clock */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	ethernet@a8000000 {
 		compatible = "davicom,dm9000";
-		reg = <0xA8000000 0x2 0xA8000002 0x2>;
+		reg = <0xa8000000 0x2>, <0xa8000002 0x2>;
 		interrupt-parent = <&gph1>;
-		interrupts = <1 4>;
+		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 		local-mac-address = [00 00 de ad be ef];
 		davicom,no-eeprom;
 	};
@@ -47,6 +55,14 @@
 		default-brightness-level = <6>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm3_out>;
+		power-supply = <&dc5v_reg>;
+	};
+
+	dc5v_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "DC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
 	};
 };
 
@@ -68,61 +84,61 @@
 			<&keypad_col6>, <&keypad_col7>;
 	status = "okay";
 
-	key_1 {
+	key-1 {
 		keypad,row = <0>;
 		keypad,column = <3>;
 		linux,code = <KEY_1>;
 	};
 
-	key_2 {
+	key-2 {
 		keypad,row = <0>;
 		keypad,column = <4>;
 		linux,code = <KEY_2>;
 	};
 
-	key_3 {
+	key-3 {
 		keypad,row = <0>;
 		keypad,column = <5>;
 		linux,code = <KEY_3>;
 	};
 
-	key_4 {
+	key-4 {
 		keypad,row = <0>;
 		keypad,column = <6>;
 		linux,code = <KEY_4>;
 	};
 
-	key_5 {
+	key-5 {
 		keypad,row = <0
 		>;
 		keypad,column = <7>;
 		linux,code = <KEY_5>;
 	};
 
-	key_6 {
+	key-6 {
 		keypad,row = <1>;
 		keypad,column = <3>;
 		linux,code = <KEY_A>;
 	};
-	key_7 {
+	key-7 {
 		keypad,row = <1>;
 		keypad,column = <4>;
 		linux,code = <KEY_B>;
 	};
 
-	key_8 {
+	key-8 {
 		keypad,row = <1>;
 		keypad,column = <5>;
 		linux,code = <KEY_C>;
 	};
 
-	key_9 {
+	key-9 {
 		keypad,row = <1>;
 		keypad,column = <6>;
 		linux,code = <KEY_D>;
 	};
 
-	key_10 {
+	key-10 {
 		keypad,row = <1>;
 		keypad,column = <7>;
 		linux,code = <KEY_E>;
@@ -147,6 +163,8 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &sdhci0 {
diff --git a/arch/arm/boot/dts/s5pv210-torbreck.dts b/arch/arm/boot/dts/samsung/s5pv210-torbreck.dts
index cd25e72ccd84..e18259737684 100644
--- a/arch/arm/boot/dts/s5pv210-torbreck.dts
+++ b/arch/arm/boot/dts/samsung/s5pv210-torbreck.dts
@@ -30,6 +30,13 @@
 		device_type = "memory";
 		reg = <0x20000000 0x20000000>;
 	};
+
+	pmic_ap_clk: clock-0 {
+		/* Workaround for missing PMIC and its clock */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
 };
 
 &xusbxti {
@@ -54,6 +61,8 @@
 
 &rtc {
 	status = "okay";
+	clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
+	clock-names = "rtc", "rtc_src";
 };
 
 &sdhci0 {
diff --git a/arch/arm/boot/dts/s5pv210.dtsi b/arch/arm/boot/dts/samsung/s5pv210.dtsi
index 2ad642f51fd9..ed560c9a3aa1 100644
--- a/arch/arm/boot/dts/s5pv210.dtsi
+++ b/arch/arm/boot/dts/samsung/s5pv210.dtsi
@@ -8,7 +8,7 @@
  * Tomasz Figa <t.figa@samsung.com>
  *
  * Samsung's S5PV210 SoC device nodes are listed in this file. S5PV210
- * based board files can include this file and provide values for board specfic
+ * based board files can include this file and provide values for board specific
  * bindings.
  *
  * Note: This file does not include device nodes for all the controllers in
@@ -52,34 +52,26 @@
 		};
 	};
 
+	xxti: oscillator-0 {
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+		clock-output-names = "xxti";
+		#clock-cells = <0>;
+	};
+
+	xusbxti: oscillator-1 {
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+		clock-output-names = "xusbxti";
+		#clock-cells = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
-		external-clocks {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			xxti: oscillator@0 {
-				compatible = "fixed-clock";
-				reg = <0>;
-				clock-frequency = <0>;
-				clock-output-names = "xxti";
-				#clock-cells = <0>;
-			};
-
-			xusbxti: oscillator@1 {
-				compatible = "fixed-clock";
-				reg = <1>;
-				clock-frequency = <0>;
-				clock-output-names = "xusbxti";
-				#clock-cells = <0>;
-			};
-		};
-
 		onenand: onenand@b0600000 {
 			compatible = "samsung,s5pv210-onenand";
 			reg = <0xb0600000 0x2000>,
@@ -100,19 +92,16 @@
 		};
 
 		clocks: clock-controller@e0100000 {
-			compatible = "samsung,s5pv210-clock", "simple-bus";
+			compatible = "samsung,s5pv210-clock";
 			reg = <0xe0100000 0x10000>;
 			clock-names = "xxti", "xusbxti";
 			clocks = <&xxti>, <&xusbxti>;
 			#clock-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
+		};
 
-			pmu_syscon: syscon@e0108000 {
-				compatible = "samsung-s5pv210-pmu", "syscon";
-				reg = <0xe0108000 0x8000>;
-			};
+		pmu_syscon: syscon@e0108000 {
+			compatible = "samsung-s5pv210-pmu", "syscon";
+			reg = <0xe0108000 0x8000>;
 		};
 
 		pinctrl0: pinctrl@e0200000 {
@@ -128,35 +117,35 @@
 			};
 		};
 
-		amba {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges;
+		pdma0: dma-controller@e0900000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0xe0900000 0x1000>;
+			interrupt-parent = <&vic0>;
+			interrupts = <19>;
+			clocks = <&clocks CLK_PDMA0>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			pdma0: dma@e0900000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0xe0900000 0x1000>;
-				interrupt-parent = <&vic0>;
-				interrupts = <19>;
-				clocks = <&clocks CLK_PDMA0>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		pdma1: dma-controller@e0a00000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0xe0a00000 0x1000>;
+			interrupt-parent = <&vic0>;
+			interrupts = <20>;
+			clocks = <&clocks CLK_PDMA1>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+		};
 
-			pdma1: dma@e0a00000 {
-				compatible = "arm,pl330", "arm,primecell";
-				reg = <0xe0a00000 0x1000>;
-				interrupt-parent = <&vic0>;
-				interrupts = <20>;
-				clocks = <&clocks CLK_PDMA1>;
-				clock-names = "apb_pclk";
-				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
-			};
+		adc: adc@e1700000 {
+			compatible = "samsung,s5pv210-adc";
+			reg = <0xe1700000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <23>, <24>;
+			clocks = <&clocks CLK_TSADC>;
+			clock-names = "adc";
+			#io-channel-cells = <1>;
+			status = "disabled";
 		};
 
 		spi0: spi@e1300000 {
@@ -229,43 +218,36 @@
 			status = "disabled";
 		};
 
-		audio-subsystem {
-			compatible = "samsung,s5pv210-audss", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			clk_audss: clock-controller@eee10000 {
-				compatible = "samsung,s5pv210-audss-clock";
-				reg = <0xeee10000 0x1000>;
-				clock-names = "hclk", "xxti",
-						"fout_epll",
-						"sclk_audio0";
-				clocks = <&clocks DOUT_HCLKP>, <&xxti>,
-						<&clocks FOUT_EPLL>,
-						<&clocks SCLK_AUDIO0>;
-				#clock-cells = <1>;
-			};
+		clk_audss: clock-controller@eee10000 {
+			compatible = "samsung,s5pv210-audss-clock";
+			reg = <0xeee10000 0x1000>;
+			clock-names = "hclk", "xxti",
+				      "fout_epll",
+				      "sclk_audio0";
+			clocks = <&clocks DOUT_HCLKP>, <&xxti>,
+				 <&clocks FOUT_EPLL>,
+				 <&clocks SCLK_AUDIO0>;
+			#clock-cells = <1>;
+		};
 
-			i2s0: i2s@eee30000 {
-				compatible = "samsung,s5pv210-i2s";
-				reg = <0xeee30000 0x1000>;
-				interrupt-parent = <&vic2>;
-				interrupts = <16>;
-				dma-names = "rx", "tx", "tx-sec";
-				dmas = <&pdma1 9>, <&pdma1 10>, <&pdma1 11>;
-				clock-names = "iis",
-						"i2s_opclk0",
-						"i2s_opclk1";
-				clocks = <&clk_audss CLK_I2S>,
-						<&clk_audss CLK_I2S>,
-						<&clk_audss CLK_DOUT_AUD_BUS>;
-				samsung,idma-addr = <0xc0010000>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2s0_bus>;
-				#sound-dai-cells = <0>;
-				status = "disabled";
-			};
+		i2s0: i2s@eee30000 {
+			compatible = "samsung,s5pv210-i2s";
+			reg = <0xeee30000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <16>;
+			dma-names = "tx", "rx", "tx-sec";
+			dmas = <&pdma1 10>, <&pdma1 9>, <&pdma1 11>;
+			clock-names = "iis",
+				      "i2s_opclk0",
+				      "i2s_opclk1";
+			clocks = <&clk_audss CLK_I2S>,
+				 <&clk_audss CLK_I2S>,
+				 <&clk_audss CLK_DOUT_AUD_BUS>;
+			samsung,idma-addr = <0xc0010000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2s0_bus>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
 		};
 
 		i2s1: i2s@e2100000 {
@@ -273,8 +255,8 @@
 			reg = <0xe2100000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <17>;
-			dma-names = "rx", "tx";
-			dmas = <&pdma1 12>, <&pdma1 13>;
+			dma-names = "tx", "rx";
+			dmas = <&pdma1 13>, <&pdma1 12>;
 			clock-names = "iis", "i2s_opclk0";
 			clocks = <&clocks CLK_I2S1>, <&clocks SCLK_AUDIO1>;
 			pinctrl-names = "default";
@@ -288,8 +270,8 @@
 			reg = <0xe2a00000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <18>;
-			dma-names = "rx", "tx";
-			dmas = <&pdma1 14>, <&pdma1 15>;
+			dma-names = "tx", "rx";
+			dmas = <&pdma1 15>, <&pdma1 14>;
 			clock-names = "iis", "i2s_opclk0";
 			clocks = <&clocks CLK_I2S2>, <&clocks SCLK_AUDIO2>;
 			pinctrl-names = "default";
@@ -375,7 +357,7 @@
 			status = "disabled";
 		};
 
-		sdhci0: sdhci@eb000000 {
+		sdhci0: mmc@eb000000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb000000 0x100000>;
 			interrupt-parent = <&vic1>;
@@ -386,7 +368,7 @@
 			status = "disabled";
 		};
 
-		sdhci1: sdhci@eb100000 {
+		sdhci1: mmc@eb100000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb100000 0x100000>;
 			interrupt-parent = <&vic1>;
@@ -397,7 +379,7 @@
 			status = "disabled";
 		};
 
-		sdhci2: sdhci@eb200000 {
+		sdhci2: mmc@eb200000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb200000 0x100000>;
 			interrupt-parent = <&vic1>;
@@ -408,7 +390,7 @@
 			status = "disabled";
 		};
 
-		sdhci3: sdhci@eb300000 {
+		sdhci3: mmc@eb300000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb300000 0x100000>;
 			interrupt-parent = <&vic3>;
@@ -419,7 +401,7 @@
 			status = "disabled";
 		};
 
-		hsotg: hsotg@ec000000 {
+		hsotg: usb@ec000000 {
 			compatible = "samsung,s3c6400-hsotg";
 			reg = <0xec000000 0x20000>;
 			interrupt-parent = <&vic1>;
@@ -441,38 +423,28 @@
 			status = "disabled";
 		};
 
-		ehci: ehci@ec200000 {
+		ehci: usb@ec200000 {
 			compatible = "samsung,exynos4210-ehci";
 			reg = <0xec200000 0x100>;
 			interrupts = <23>;
 			interrupt-parent = <&vic1>;
 			clocks = <&clocks CLK_USB_HOST>;
 			clock-names = "usbhost";
-			#address-cells = <1>;
-			#size-cells = <0>;
+			phys = <&usbphy 1>;
+			phy-names = "host";
 			status = "disabled";
-
-			port@0 {
-				reg = <0>;
-				phys = <&usbphy 1>;
-			};
 		};
 
-		ohci: ohci@ec300000 {
+		ohci: usb@ec300000 {
 			compatible = "samsung,exynos4210-ohci";
 			reg = <0xec300000 0x100>;
 			interrupts = <23>;
 			interrupt-parent = <&vic1>;
 			clocks = <&clocks CLK_USB_HOST>;
 			clock-names = "usbhost";
-			#address-cells = <1>;
-			#size-cells = <0>;
+			phys = <&usbphy 1>;
+			phy-names = "host";
 			status = "disabled";
-
-			port@0 {
-				reg = <0>;
-				phys = <&usbphy 1>;
-			};
 		};
 
 		mfc: codec@f1700000 {
@@ -480,8 +452,8 @@
 			reg = <0xf1700000 0x10000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <14>;
-			clocks = <&clocks DOUT_MFC>, <&clocks CLK_MFC>;
-			clock-names = "sclk_mfc", "mfc";
+			clocks = <&clocks CLK_MFC>, <&clocks DOUT_MFC>;
+			clock-names = "mfc", "sclk_mfc";
 		};
 
 		vic0: interrupt-controller@f2000000 {
@@ -542,7 +514,7 @@
 			clock-names = "sclk_fimg2d", "fimg2d";
 		};
 
-		mdma1: mdma@fa200000 {
+		mdma1: dma-controller@fa200000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xfa200000 0x1000>;
 			interrupt-parent = <&vic0>;
@@ -550,8 +522,6 @@
 			clocks = <&clocks CLK_MDMA>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 		};
 
 		rotator: rotator@fa300000 {
@@ -577,26 +547,24 @@
 			status = "disabled";
 		};
 
-		camera: camera {
-			compatible = "samsung,fimc", "simple-bus";
-			pinctrl-names = "default";
-			pinctrl-0 = <>;
+		camera: camera@fa600000 {
+			compatible = "samsung,fimc";
+			ranges = <0x0 0xfa600000 0xe01000>;
 			clocks = <&clocks SCLK_CAM0>, <&clocks SCLK_CAM1>;
 			clock-names = "sclk_cam0", "sclk_cam1";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			#clock-cells = <1>;
 			clock-output-names = "cam_a_clkout", "cam_b_clkout";
-			ranges;
 
-			csis0: csis@fa600000 {
+			csis0: csis@0 {
 				compatible = "samsung,s5pv210-csis";
-				reg = <0xfa600000 0x4000>;
+				reg = <0x00000000 0x4000>;
 				interrupt-parent = <&vic2>;
 				interrupts = <29>;
 				clocks = <&clocks CLK_CSIS>,
 						<&clocks SCLK_CSIS>;
-				clock-names = "clk_csis",
+				clock-names = "csis",
 						"sclk_csis";
 				bus-width = <4>;
 				status = "disabled";
@@ -604,9 +572,9 @@
 				#size-cells = <0>;
 			};
 
-			fimc0: fimc@fb200000 {
+			fimc0: fimc@c00000 {
 				compatible = "samsung,s5pv210-fimc";
-				reg = <0xfb200000 0x1000>;
+				reg = <0x00c00000 0x1000>;
 				interrupts = <5>;
 				interrupt-parent = <&vic2>;
 				clocks = <&clocks CLK_FIMC0>,
@@ -614,13 +582,13 @@
 				clock-names = "fimc",
 						"sclk_fimc";
 				samsung,pix-limits = <4224 8192 1920 4224>;
-				samsung,mainscaler-ext;
+				samsung,min-pix-alignment = <16 8>;
 				samsung,cam-if;
 			};
 
-			fimc1: fimc@fb300000 {
+			fimc1: fimc@d00000 {
 				compatible = "samsung,s5pv210-fimc";
-				reg = <0xfb300000 0x1000>;
+				reg = <0x00d00000 0x1000>;
 				interrupt-parent = <&vic2>;
 				interrupts = <6>;
 				clocks = <&clocks CLK_FIMC1>,
@@ -628,22 +596,25 @@
 				clock-names = "fimc",
 						"sclk_fimc";
 				samsung,pix-limits = <4224 8192 1920 4224>;
+				samsung,min-pix-alignment = <1 1>;
 				samsung,mainscaler-ext;
 				samsung,cam-if;
+				samsung,lcd-wb;
 			};
 
-			fimc2: fimc@fb400000 {
+			fimc2: fimc@e00000 {
 				compatible = "samsung,s5pv210-fimc";
-				reg = <0xfb400000 0x1000>;
+				reg = <0x00e00000 0x1000>;
 				interrupt-parent = <&vic2>;
 				interrupts = <7>;
 				clocks = <&clocks CLK_FIMC2>,
 						<&clocks SCLK_FIMC2>;
 				clock-names = "fimc",
 						"sclk_fimc";
-				samsung,pix-limits = <4224 8192 1920 4224>;
-				samsung,mainscaler-ext;
-				samsung,lcd-wb;
+				samsung,pix-limits = <1920 8192 1280 1920>;
+				samsung,min-pix-alignment = <16 8>;
+				samsung,rotators = <0>;
+				samsung,cam-if;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/sigmastar/Makefile b/arch/arm/boot/dts/sigmastar/Makefile
new file mode 100644
index 000000000000..b07eaf5d8add
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MSTARV7) += \
+	mstar-infinity-msc313-breadbee_crust.dtb \
+	mstar-infinity2m-ssd202d-100ask-dongshanpione.dtb \
+	mstar-infinity2m-ssd202d-miyoo-mini.dtb \
+	mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dtb \
+	mstar-infinity2m-ssd202d-ssd201htv2.dtb \
+	mstar-infinity2m-ssd202d-unitv2.dtb \
+	mstar-infinity3-msc313e-breadbee.dtb \
+	mstar-mercury5-ssc8336n-midrived08.dtb
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity-breadbee-common.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity-breadbee-common.dtsi
new file mode 100644
index 000000000000..507ff2fba837
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity-breadbee-common.dtsi
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	vcc_core: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_core";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-boot-on;
+	};
+
+	vcc_dram: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_dram";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+	};
+
+	vcc_io: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_io";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		red {
+			gpios = <&gpio MSC313_GPIO_SR_IO16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "activity";
+		};
+		yellow {
+			gpios = <&gpio MSC313_GPIO_SR_IO17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vcc_core>;
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity-msc313-breadbee_crust.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity-msc313-breadbee_crust.dts
new file mode 100644
index 000000000000..db4910dcb8a7
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity-msc313-breadbee_crust.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity-msc313.dtsi"
+#include "mstar-infinity-breadbee-common.dtsi"
+
+/ {
+	model = "BreadBee Crust";
+	compatible = "thingyjp,breadbee-crust", "mstar,infinity";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity-msc313.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity-msc313.dtsi
new file mode 100644
index 000000000000..3499fde263be
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity-msc313.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-infinity.dtsi"
+
+/ {
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x4000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity.dtsi
new file mode 100644
index 000000000000..441a917b88ba
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-v7.dtsi"
+
+#include <dt-bindings/gpio/msc313-gpio.h>
+
+/ {
+	cpu0_opp_table: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-240000000 {
+			opp-hz = /bits/ 64 <240000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+	};
+};
+
+&cpu0 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&imi {
+	reg = <0xa0000000 0x16000>;
+};
+
+&gpio {
+	compatible = "mstar,msc313-gpio";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd201-som2d01.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd201-som2d01.dtsi
new file mode 100644
index 000000000000..34df472fed71
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd201-som2d01.dtsi
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ * Author: Romain Perier <romain.perier@gmail.com>
+ */
+
+/ {
+	reg_vcc_dram: regulator-vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_dram";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-100ask-dongshanpione.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-100ask-dongshanpione.dts
new file mode 100644
index 000000000000..f25a04c98ccb
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-100ask-dongshanpione.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+
+/ {
+	model = "DongShanPi One";
+	compatible = "100ask,dongshanpione", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-miyoo-mini.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-miyoo-mini.dts
new file mode 100644
index 000000000000..1bbbf47132dc
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-miyoo-mini.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+
+/ {
+	model = "Miyoo Mini";
+	compatible = "miyoo,miyoo-mini", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-ssd201htv2.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-ssd201htv2.dts
new file mode 100644
index 000000000000..5d81641414a2
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-ssd201htv2.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+
+/ {
+	model = "SSD201_HT_V2";
+	compatible = "honestar,ssd201htv2", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-unitv2.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-unitv2.dts
new file mode 100644
index 000000000000..a81684002e45
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-unitv2.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+
+/ {
+	model = "UnitV2";
+	compatible = "m5stack,unitv2", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dts
new file mode 100644
index 000000000000..b15c40762bc0
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ * Author: Romain Perier <romain.perier@gmail.com>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Wireless Tag IDO-SBC2D06-1VB-22W";
+	compatible = "wirelesstag,ido-sbc2d06-v1b-22w", "mstar,infinity2m";
+
+	leds {
+		compatible = "gpio-leds";
+		sys_led {
+			gpios = <&gpio SSD20XD_GPIO_GPIO85 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi
new file mode 100644
index 000000000000..d877aff85033
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ * Author: Romain Perier <romain.perier@gmail.com>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+#include "mstar-infinity2m-ssd201-som2d01.dtsi"
+
+/ {
+	model = "Wireless Tag IDO-SOM2D01 (SSD202D)";
+	compatible = "wirelesstag,ido-som2d01", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&reg_vcc_dram {
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d.dtsi
new file mode 100644
index 000000000000..176e10a29896
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd202d.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-infinity2m-ssd20xd.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x20000000 0x8000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd20xd.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd20xd.dtsi
new file mode 100644
index 000000000000..6f067da61ba3
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m-ssd20xd.dtsi
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-infinity2m.dtsi"
+
+&gpio {
+	compatible = "sstar,ssd20xd-gpio";
+	status = "okay";
+};
+
+&smpctrl {
+	compatible = "sstar,ssd201-smpctrl", "mstar,smpctrl";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi
new file mode 100644
index 000000000000..1b485efd7156
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-infinity.dtsi"
+
+&cpu0_opp_table {
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+};
+
+&cpus {
+	cpu1: cpu@1 {
+		device_type = "cpu";
+		compatible = "arm,cortex-a7";
+		operating-points-v2 = <&cpu0_opp_table>;
+		reg = <0x1>;
+		clocks = <&cpupll>;
+		clock-names = "cpuclk";
+	};
+};
+
+&riu {
+	smpctrl: smpctrl@204000 {
+		reg = <0x204000 0x200>;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity3-msc313e-breadbee.dts b/arch/arm/boot/dts/sigmastar/mstar-infinity3-msc313e-breadbee.dts
new file mode 100644
index 000000000000..e64ca4ce1830
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity3-msc313e-breadbee.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity3-msc313e.dtsi"
+#include "mstar-infinity-breadbee-common.dtsi"
+
+/ {
+	model = "BreadBee";
+	compatible = "thingyjp,breadbee", "mstar,infinity3";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity3-msc313e.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity3-msc313e.dtsi
new file mode 100644
index 000000000000..f581b6f89555
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity3-msc313e.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-infinity3.dtsi"
+
+/ {
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x4000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity3.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity3.dtsi
new file mode 100644
index 000000000000..a56cf29e5d82
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity3.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-infinity.dtsi"
+
+&cpu0_opp_table {
+	opp-1008000000 {
+		opp-hz = /bits/ 64 <1008000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+	};
+
+	// overclock frequencies below, shown to work fine up to 1.3 GHz
+	opp-108000000 {
+		opp-hz = /bits/ 64 <1080000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1188000000 {
+		opp-hz = /bits/ 64 <1188000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1296000000 {
+		opp-hz = /bits/ 64 <1296000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1350000000 {
+		opp-hz = /bits/ 64 <1350000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1404000000 {
+		opp-hz = /bits/ 64 <1404000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1458000000 {
+		opp-hz = /bits/ 64 <1458000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1512000000 {
+		opp-hz = /bits/ 64 <1512000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+};
+
+&imi {
+	reg = <0xa0000000 0x20000>;
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-mercury5-ssc8336n-midrived08.dts b/arch/arm/boot/dts/sigmastar/mstar-mercury5-ssc8336n-midrived08.dts
new file mode 100644
index 000000000000..7306b737d9c4
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-mercury5-ssc8336n-midrived08.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-mercury5-ssc8336n.dtsi"
+
+/ {
+	model = "70mai Midrive D08";
+	compatible = "70mai,midrived08", "mstar,mercury5";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-mercury5-ssc8336n.dtsi b/arch/arm/boot/dts/sigmastar/mstar-mercury5-ssc8336n.dtsi
new file mode 100644
index 000000000000..3f5a4c029744
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-mercury5-ssc8336n.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-mercury5.dtsi"
+
+/ {
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x4000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-mercury5.dtsi b/arch/arm/boot/dts/sigmastar/mstar-mercury5.dtsi
new file mode 100644
index 000000000000..a7d0dd9d6132
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-mercury5.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include "mstar-v7.dtsi"
+
+&imi {
+	reg = <0xa0000000 0x20000>;
+};
diff --git a/arch/arm/boot/dts/sigmastar/mstar-v7.dtsi b/arch/arm/boot/dts/sigmastar/mstar-v7.dtsi
new file mode 100644
index 000000000000..3eeafd8c7121
--- /dev/null
+++ b/arch/arm/boot/dts/sigmastar/mstar-v7.dtsi
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2020 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mstar-msc313-mpll.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus: cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			clocks = <&cpupll>;
+			clock-names = "cpuclk";
+		};
+	};
+
+	arch_timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2)
+				| IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2)
+				| IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2)
+				| IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2)
+				| IRQ_TYPE_LEVEL_LOW)>;
+		/*
+		 * we shouldn't need this but the vendor
+		 * u-boot is broken
+		 */
+		clock-frequency = <6000000>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+	};
+
+	clocks: clocks {
+		xtal: xtal {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		rtc_xtal: rtc_xtal {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			status = "disabled";
+		};
+
+		xtal_div2: xtal_div2 {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&xtal>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x16001000 0x16001000 0x00007000>,
+			 <0x1f000000 0x1f000000 0x00400000>,
+			 <0xa0000000 0xa0000000 0x20000>;
+
+		gic: interrupt-controller@16001000 {
+			compatible = "arm,cortex-a7-gic";
+			reg = <0x16001000 0x1000>,
+			      <0x16002000 0x2000>,
+			      <0x16004000 0x2000>,
+			      <0x16006000 0x2000>;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2)
+					| IRQ_TYPE_LEVEL_LOW)>;
+		};
+
+		riu: bus@1f000000 {
+			compatible = "simple-bus";
+			reg = <0x1f000000 0x00400000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x1f000000 0x00400000>;
+
+			pmsleep: syscon@1c00 {
+				compatible = "mstar,msc313-pmsleep", "syscon";
+				reg = <0x1c00 0x100>;
+			};
+
+			reboot {
+				compatible = "syscon-reboot";
+				regmap = <&pmsleep>;
+				offset = <0xb8>;
+				mask = <0x79>;
+			};
+
+			rtc@2400 {
+				compatible = "mstar,msc313-rtc";
+				reg = <0x2400 0x40>;
+				clocks = <&xtal_div2>;
+				interrupts-extended = <&intc_irq GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			watchdog@6000 {
+				compatible = "mstar,msc313e-wdt";
+				reg = <0x6000 0x1f>;
+				clocks = <&xtal_div2>;
+			};
+
+
+			intc_fiq: interrupt-controller@201310 {
+				compatible = "mstar,mst-intc";
+				reg = <0x201310 0x40>;
+				#interrupt-cells = <3>;
+				interrupt-controller;
+				interrupt-parent = <&gic>;
+				mstar,irqs-map-range = <96 127>;
+			};
+
+			intc_irq: interrupt-controller@201350 {
+				compatible = "mstar,mst-intc";
+				reg = <0x201350 0x40>;
+				#interrupt-cells = <3>;
+				interrupt-controller;
+				interrupt-parent = <&gic>;
+				mstar,irqs-map-range = <32 95>;
+				mstar,intc-no-eoi;
+			};
+
+			l3bridge: l3bridge@204400 {
+				compatible = "mstar,l3bridge";
+				reg = <0x204400 0x200>;
+			};
+
+			mpll: mpll@206000 {
+				compatible = "mstar,msc313-mpll";
+				#clock-cells = <1>;
+				reg = <0x206000 0x200>;
+				clocks = <&xtal>;
+			};
+
+			cpupll: cpupll@206400 {
+				compatible = "mstar,msc313-cpupll";
+				reg = <0x206400 0x200>;
+				#clock-cells = <0>;
+				clocks = <&mpll MSTAR_MSC313_MPLL_DIV2>;
+			};
+
+			gpio: gpio@207800 {
+				#gpio-cells = <2>;
+				reg = <0x207800 0x200>;
+				gpio-controller;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				interrupt-parent = <&intc_fiq>;
+				status = "disabled";
+			};
+
+			pm_uart: serial@221000 {
+				compatible = "ns16550a";
+				reg = <0x221000 0x100>;
+				reg-shift = <3>;
+				interrupts-extended = <&intc_irq GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency = <172000000>;
+				status = "disabled";
+			};
+		};
+
+		imi: sram@a0000000 {
+			compatible = "mmio-sram";
+			reg = <0xa0000000 0x10000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/socionext/Makefile b/arch/arm/boot/dts/socionext/Makefile
new file mode 100644
index 000000000000..dab4275f6bd6
--- /dev/null
+++ b/arch/arm/boot/dts/socionext/Makefile
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MILBEAUT) += milbeaut-m10v-evb.dtb
+dtb-$(CONFIG_ARCH_UNIPHIER) += \
+	uniphier-ld4-ref.dtb \
+	uniphier-ld6b-ref.dtb \
+	uniphier-pro4-ace.dtb \
+	uniphier-pro4-ref.dtb \
+	uniphier-pro4-sanji.dtb \
+	uniphier-pro5-epcore.dtb \
+	uniphier-pro5-proex.dtb \
+	uniphier-pxs2-gentil.dtb \
+	uniphier-pxs2-vodka.dtb \
+	uniphier-sld8-ref.dtb
diff --git a/arch/arm/boot/dts/milbeaut-m10v-evb.dts b/arch/arm/boot/dts/socionext/milbeaut-m10v-evb.dts
index 614f60c6b0a2..614f60c6b0a2 100644
--- a/arch/arm/boot/dts/milbeaut-m10v-evb.dts
+++ b/arch/arm/boot/dts/socionext/milbeaut-m10v-evb.dts
diff --git a/arch/arm/boot/dts/milbeaut-m10v.dtsi b/arch/arm/boot/dts/socionext/milbeaut-m10v.dtsi
index aa7c6caeb750..75f0c0af2270 100644
--- a/arch/arm/boot/dts/milbeaut-m10v.dtsi
+++ b/arch/arm/boot/dts/socionext/milbeaut-m10v.dtsi
@@ -65,10 +65,18 @@
 			      <0x1d002000 0x1000>; /* CPU I/f base and size */
 		};
 
+		clk: clock-ctrl@1d021000 {
+			compatible = "socionext,milbeaut-m10v-ccu";
+			#clock-cells = <1>;
+			reg = <0x1d021000 0x1000>;
+			clocks = <&uclk40xi>;
+		};
+
 		timer@1e000050 { /* 32-bit Reload Timers */
 			compatible = "socionext,milbeaut-timer";
 			reg = <0x1e000050 0x20>;
 			interrupts = <0 91 4>;
+			clocks = <&clk 4>;
 		};
 
 		uart1: serial@1e700010 { /* PE4, PE5 */
@@ -77,6 +85,7 @@
 			reg = <0x1e700010 0x10>;
 			interrupts = <0 141 0x4>, <0 149 0x4>;
 			interrupt-names = "rx", "tx";
+			clocks = <&clk 2>;
 		};
 
 	};
diff --git a/arch/arm/boot/dts/uniphier-ld4-ref.dts b/arch/arm/boot/dts/socionext/uniphier-ld4-ref.dts
index f2d060f403cc..e007db084787 100644
--- a/arch/arm/boot/dts/uniphier-ld4-ref.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-ld4-ref.dts
@@ -20,7 +20,7 @@
 
 	aliases {
 		serial0 = &serial0;
-		serial1 = &serial1;
+		serial1 = &serialsc;
 		serial2 = &serial2;
 		serial3 = &serial3;
 		i2c0 = &i2c0;
@@ -36,7 +36,11 @@
 };
 
 &ethsc {
-	interrupts = <1 8>;
+	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&serialsc {
+	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -52,7 +56,7 @@
 };
 
 &gpio {
-	xirq1 {
+	xirq1-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(1) 0>;
 		input;
diff --git a/arch/arm/boot/dts/uniphier-ld4.dtsi b/arch/arm/boot/dts/socionext/uniphier-ld4.dtsi
index 58cd4e8fa5be..df2de7a40211 100644
--- a/arch/arm/boot/dts/uniphier-ld4.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-ld4.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-ld4";
@@ -51,11 +52,12 @@
 		ranges;
 		interrupt-parent = <&intc>;
 
-		l2: l2-cache@500c0000 {
+		l2: cache-controller@500c0000 {
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x4>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(512 * 1024)>;
 			cache-sets = <256>;
@@ -67,7 +69,9 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006000 0x100>;
-			interrupts = <0 39 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -78,7 +82,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -89,7 +93,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -100,7 +104,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -111,7 +115,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 29 4>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -138,7 +142,7 @@
 			reg = <0x58400000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 1>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -152,7 +156,7 @@
 			reg = <0x58480000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 1>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -166,7 +170,7 @@
 			reg = <0x58500000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 1>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -180,7 +184,7 @@
 			reg = <0x58580000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 1>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -203,33 +207,33 @@
 			reg = <0x59801000 0x400>;
 		};
 
-		mioctrl@59810000 {
+		syscon@59810000 {
 			compatible = "socionext,uniphier-ld4-mioctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59810000 0x800>;
 
-			mio_clk: clock {
+			mio_clk: clock-controller {
 				compatible = "socionext,uniphier-ld4-mio-clock";
 				#clock-cells = <1>;
 			};
 
-			mio_rst: reset {
+			mio_rst: reset-controller {
 				compatible = "socionext,uniphier-ld4-mio-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		perictrl@59820000 {
+		syscon@59820000 {
 			compatible = "socionext,uniphier-ld4-perictrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59820000 0x200>;
 
-			peri_clk: clock {
+			peri_clk: clock-controller {
 				compatible = "socionext,uniphier-ld4-peri-clock";
 				#clock-cells = <1>;
 			};
 
-			peri_rst: reset {
+			peri_rst: reset-controller {
 				compatible = "socionext,uniphier-ld4-peri-reset";
 				#reset-cells = <1>;
 			};
@@ -238,18 +242,23 @@
 		dmac: dma-controller@5a000000 {
 			compatible = "socionext,uniphier-mio-dmac";
 			reg = <0x5a000000 0x1000>;
-			interrupts = <0 68 4>, <0 68 4>, <0 69 4>, <0 70 4>,
-				     <0 71 4>, <0 72 4>, <0 73 4>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mio_clk 7>;
 			resets = <&mio_rst 7>;
 			#dma-cells = <1>;
 		};
 
-		sd: sdhc@5a400000 {
+		sd: mmc@5a400000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a400000 0x200>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -265,11 +274,11 @@
 			sd-uhs-sdr50;
 		};
 
-		emmc: sdhc@5a500000 {
+		emmc: mmc@5a500000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a500000 0x200>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&mio_clk 1>;
@@ -287,7 +296,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 80 4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -301,7 +310,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 81 4>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -315,7 +324,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a820100 0x100>;
-			interrupts = <0 82 4>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 10>,
@@ -325,7 +334,7 @@
 			has-transaction-translator;
 		};
 
-		soc-glue@5f800000 {
+		syscon@5f800000 {
 			compatible = "socionext,uniphier-ld4-soc-glue",
 				     "simple-mfd", "syscon";
 			reg = <0x5f800000 0x2000>;
@@ -335,9 +344,10 @@
 			};
 		};
 
-		soc-glue@5f900000 {
+		syscon@5f900000 {
 			compatible = "socionext,uniphier-ld4-soc-glue-debug",
-				     "simple-mfd";
+				     "simple-mfd", "syscon";
+			reg = <0x5f900000 0x2000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x5f900000 0x2000>;
@@ -356,14 +366,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x104>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x104>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -375,42 +387,43 @@
 			interrupt-controller;
 		};
 
-		aidet: aidet@61830000 {
+		aidet: interrupt-controller@61830000 {
 			compatible = "socionext,uniphier-ld4-aidet";
 			reg = <0x61830000 0x200>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
 
-		sysctrl@61840000 {
+		syscon@61840000 {
 			compatible = "socionext,uniphier-ld4-sysctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x61840000 0x10000>;
 
-			sys_clk: clock {
+			sys_clk: clock-controller {
 				compatible = "socionext,uniphier-ld4-clock";
 				#clock-cells = <1>;
 			};
 
-			sys_rst: reset {
+			sys_rst: reset-controller {
 				compatible = "socionext,uniphier-ld4-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		nand: nand@68000000 {
+		nand: nand-controller@68000000 {
 			compatible = "socionext,uniphier-denali-nand-v5a";
 			status = "disabled";
 			reg-names = "nand_data", "denali_reg";
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
 			clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>;
-			resets = <&sys_rst 2>;
+			reset-names = "nand", "reg";
+			resets = <&sys_rst 2>, <&sys_rst 2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/uniphier-ld6b-ref.dts b/arch/arm/boot/dts/socionext/uniphier-ld6b-ref.dts
index 60994b6e8b99..223a78b4a761 100644
--- a/arch/arm/boot/dts/uniphier-ld6b-ref.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-ld6b-ref.dts
@@ -22,6 +22,7 @@
 		serial0 = &serial0;
 		serial1 = &serial1;
 		serial2 = &serial2;
+		serial3 = &serialsc;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c2 = &i2c2;
@@ -29,6 +30,7 @@
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &eth;
 	};
 
 	memory@80000000 {
@@ -38,7 +40,11 @@
 };
 
 &ethsc {
-	interrupts = <4 8>;
+	interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&serialsc {
+	interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -54,7 +60,7 @@
 };
 
 &gpio {
-	xirq4 {
+	xirq4-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(4) 0>;
 		input;
@@ -75,7 +81,7 @@
 };
 
 &mdio {
-	ethphy: ethphy@0 {
+	ethphy: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
diff --git a/arch/arm/boot/dts/uniphier-ld6b.dtsi b/arch/arm/boot/dts/socionext/uniphier-ld6b.dtsi
index 4d07a94c6b34..4d07a94c6b34 100644
--- a/arch/arm/boot/dts/uniphier-ld6b.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-ld6b.dtsi
diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/socionext/uniphier-pinctrl.dtsi
index 1fee5ffbfb9c..f909ec2e5333 100644
--- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-pinctrl.dtsi
@@ -106,6 +106,16 @@
 		function = "i2c4";
 	};
 
+	pinctrl_i2c5: i2c5 {
+		groups = "i2c5";
+		function = "i2c5";
+	};
+
+	pinctrl_i2c6: i2c6 {
+		groups = "i2c6";
+		function = "i2c6";
+	};
+
 	pinctrl_nand: nand {
 		groups = "nand";
 		function = "nand";
@@ -116,6 +126,11 @@
 		function = "nand";
 	};
 
+	pinctrl_pcie: pcie {
+		groups = "pcie";
+		function = "pcie";
+	};
+
 	pinctrl_sd: sd {
 		groups = "sd";
 		function = "sd";
@@ -181,11 +196,21 @@
 		function = "usb0";
 	};
 
+	pinctrl_usb0_device: usb0-device {
+		groups = "usb0_device";
+		function = "usb0";
+	};
+
 	pinctrl_usb1: usb1 {
 		groups = "usb1";
 		function = "usb1";
 	};
 
+	pinctrl_usb1_device: usb1-device {
+		groups = "usb1_device";
+		function = "usb1";
+	};
+
 	pinctrl_usb2: usb2 {
 		groups = "usb2";
 		function = "usb2";
diff --git a/arch/arm/boot/dts/uniphier-pro4-ace.dts b/arch/arm/boot/dts/socionext/uniphier-pro4-ace.dts
index 92cc48dd86d0..6baee4410d9c 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ace.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-pro4-ace.dts
@@ -26,6 +26,7 @@
 		i2c3 = &i2c3;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &eth;
 	};
 
 	memory@80000000 {
@@ -86,7 +87,7 @@
 };
 
 &mdio {
-	ethphy: ethphy@1 {
+	ethphy: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
@@ -98,3 +99,11 @@
 &usb1 {
 	status = "okay";
 };
+
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pro4-ref.dts b/arch/arm/boot/dts/socionext/uniphier-pro4-ref.dts
index 854f2eba3e72..d2ce5c039865 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ref.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-pro4-ref.dts
@@ -22,13 +22,14 @@
 		serial0 = &serial0;
 		serial1 = &serial1;
 		serial2 = &serial2;
-		serial3 = &serial3;
+		serial3 = &serialsc;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c2 = &i2c2;
 		i2c3 = &i2c3;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &eth;
 	};
 
 	memory@80000000 {
@@ -38,7 +39,11 @@
 };
 
 &ethsc {
-	interrupts = <2 8>;
+	interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&serialsc {
+	interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -54,7 +59,7 @@
 };
 
 &gpio {
-	xirq2 {
+	xirq2-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(2) 0>;
 		input;
@@ -83,7 +88,7 @@
 };
 
 &mdio {
-	ethphy: ethphy@0 {
+	ethphy: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
@@ -103,3 +108,11 @@
 		reg = <0>;
 	};
 };
+
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pro4-sanji.dts b/arch/arm/boot/dts/socionext/uniphier-pro4-sanji.dts
index dda1a2f214a8..7b6faf2e795e 100644
--- a/arch/arm/boot/dts/uniphier-pro4-sanji.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-pro4-sanji.dts
@@ -25,6 +25,7 @@
 		i2c3 = &i2c3;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &eth;
 	};
 
 	memory@80000000 {
@@ -81,7 +82,7 @@
 };
 
 &mdio {
-	ethphy: ethphy@1 {
+	ethphy: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/socionext/uniphier-pro4.dtsi
index 7f64e5a616d6..ba55af30e904 100644
--- a/arch/arm/boot/dts/uniphier-pro4.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-pro4.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-pro4";
@@ -59,11 +60,12 @@
 		ranges;
 		interrupt-parent = <&intc>;
 
-		l2: l2-cache@500c0000 {
+		l2: cache-controller@500c0000 {
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x4>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(768 * 1024)>;
 			cache-sets = <256>;
@@ -75,7 +77,9 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006000 0x100>;
-			interrupts = <0 39 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -86,7 +90,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -97,7 +101,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -108,7 +112,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -119,7 +123,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -146,7 +150,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -160,7 +164,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -174,7 +178,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -188,7 +192,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -204,7 +208,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -216,7 +220,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -237,33 +241,33 @@
 			reg = <0x59801000 0x400>;
 		};
 
-		mioctrl@59810000 {
+		mioctrl: syscon@59810000 {
 			compatible = "socionext,uniphier-pro4-mioctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59810000 0x800>;
 
-			mio_clk: clock {
+			mio_clk: clock-controller {
 				compatible = "socionext,uniphier-pro4-mio-clock";
 				#clock-cells = <1>;
 			};
 
-			mio_rst: reset {
+			mio_rst: reset-controller {
 				compatible = "socionext,uniphier-pro4-mio-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		perictrl@59820000 {
+		syscon@59820000 {
 			compatible = "socionext,uniphier-pro4-perictrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59820000 0x200>;
 
-			peri_clk: clock {
+			peri_clk: clock-controller {
 				compatible = "socionext,uniphier-pro4-peri-clock";
 				#clock-cells = <1>;
 			};
 
-			peri_rst: reset {
+			peri_rst: reset-controller {
 				compatible = "socionext,uniphier-pro4-peri-reset";
 				#reset-cells = <1>;
 			};
@@ -272,18 +276,24 @@
 		dmac: dma-controller@5a000000 {
 			compatible = "socionext,uniphier-mio-dmac";
 			reg = <0x5a000000 0x1000>;
-			interrupts = <0 68 4>, <0 68 4>, <0 69 4>, <0 70 4>,
-				     <0 71 4>, <0 72 4>, <0 73 4>, <0 74 4>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mio_clk 7>;
 			resets = <&mio_rst 7>;
 			#dma-cells = <1>;
 		};
 
-		sd: sdhc@5a400000 {
+		sd: mmc@5a400000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a400000 0x200>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -297,13 +307,14 @@
 			sd-uhs-sdr12;
 			sd-uhs-sdr25;
 			sd-uhs-sdr50;
+			socionext,syscon-uhs-mode = <&mioctrl 0>;
 		};
 
-		emmc: sdhc@5a500000 {
+		emmc: mmc@5a500000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a500000 0x200>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&mio_clk 1>;
@@ -317,11 +328,11 @@
 			non-removable;
 		};
 
-		sd1: sdhc@5a600000 {
+		sd1: mmc@5a600000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a600000 0x200>;
-			interrupts = <0 85 4>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sd1>;
 			clocks = <&mio_clk 2>;
@@ -337,7 +348,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 80 4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -353,7 +364,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 81 4>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb3>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -365,7 +376,7 @@
 			has-transaction-translator;
 		};
 
-		soc_glue: soc-glue@5f800000 {
+		soc_glue: syscon@5f800000 {
 			compatible = "socionext,uniphier-pro4-soc-glue",
 				     "simple-mfd", "syscon";
 			reg = <0x5f800000 0x2000>;
@@ -374,7 +385,7 @@
 				compatible = "socionext,uniphier-pro4-pinctrl";
 			};
 
-			usb-phy {
+			usb-hub {
 				compatible = "socionext,uniphier-pro4-usb2-phy";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -401,11 +412,17 @@
 					vbus-supply = <&usb1_vbus>;
 				};
 			};
+
+			sg_clk: clock-controller {
+				compatible = "socionext,uniphier-pro4-sg-clock";
+				#clock-cells = <1>;
+			};
 		};
 
-		soc-glue@5f900000 {
+		syscon@5f900000 {
 			compatible = "socionext,uniphier-pro4-soc-glue-debug",
-				     "simple-mfd";
+				     "simple-mfd", "syscon";
+			reg = <0x5f900000 0x2000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x5f900000 0x2000>;
@@ -426,7 +443,15 @@
 			};
 		};
 
-		aidet: aidet@5fc20000 {
+		xdmac: dma-controller@5fc10000 {
+			compatible = "socionext,uniphier-xdmac";
+			reg = <0x5fc10000 0x5300>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <2>;
+		};
+
+		aidet: interrupt-controller@5fc20000 {
 			compatible = "socionext,uniphier-pro4-aidet";
 			reg = <0x5fc20000 0x200>;
 			interrupt-controller;
@@ -436,14 +461,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x304>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x304>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -455,17 +482,17 @@
 			interrupt-controller;
 		};
 
-		sysctrl@61840000 {
+		syscon@61840000 {
 			compatible = "socionext,uniphier-pro4-sysctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x61840000 0x10000>;
 
-			sys_clk: clock {
+			sys_clk: clock-controller {
 				compatible = "socionext,uniphier-pro4-clock";
 				#clock-cells = <1>;
 			};
 
-			sys_rst: reset {
+			sys_rst: reset-controller {
 				compatible = "socionext,uniphier-pro4-reset";
 				#reset-cells = <1>;
 			};
@@ -475,7 +502,7 @@
 			compatible = "socionext,uniphier-pro4-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether_rgmii>;
 			clock-names = "gio", "ether", "ether-gb", "ether-phy";
@@ -493,12 +520,107 @@
 			};
 		};
 
+		ahci0: sata@65600000 {
+			compatible = "socionext,uniphier-pro4-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65600000 0x10000>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 12>, <&sys_clk 28>;
+			resets = <&sys_rst 12>, <&sys_rst 28>, <&ahci0_rst 3>;
+			ports-implemented = <1>;
+			phys = <&ahci0_phy>;
+			assigned-clocks = <&sg_clk 0>;
+			assigned-clock-rates = <25000000>;
+		};
+
+		sata-controller@65700000 {
+			compatible = "socionext,uniphier-pxs2-ahci-glue",
+				     "simple-mfd";
+			reg = <0x65700000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65700000 0x100>;
+
+			ahci0_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pro4-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 28>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 28>;
+				#reset-cells = <1>;
+			};
+
+			ahci0_phy: phy@10 {
+				compatible = "socionext,uniphier-pro4-ahci-phy";
+				reg = <0x10 0x40>;
+				clock-names = "link", "gio";
+				clocks = <&sys_clk 28>, <&sys_clk 12>;
+				reset-names = "link", "gio", "phy",
+					      "pm", "tx", "rx";
+				resets = <&sys_rst 28>, <&sys_rst 12>,
+					 <&sys_rst 30>,
+					 <&ahci0_rst 0>, <&ahci0_rst 1>,
+					 <&ahci0_rst 2>;
+				#phy-cells = <0>;
+			};
+		};
+
+		ahci1: sata@65800000 {
+			compatible = "socionext,uniphier-pro4-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65800000 0x10000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 12>, <&sys_clk 29>;
+			resets = <&sys_rst 12>, <&sys_rst 29>, <&ahci1_rst 3>;
+			ports-implemented = <1>;
+			phys = <&ahci1_phy>;
+			assigned-clocks = <&sg_clk 0>;
+			assigned-clock-rates = <25000000>;
+		};
+
+		sata-controller@65900000 {
+			compatible = "socionext,uniphier-pro4-ahci-glue",
+				     "simple-mfd";
+			reg = <0x65900000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65900000 0x100>;
+
+			ahci1_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pro4-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 29>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 29>;
+				#reset-cells = <1>;
+			};
+
+			ahci1_phy: phy@10 {
+				compatible = "socionext,uniphier-pro4-ahci-phy";
+				reg = <0x10 0x40>;
+				clock-names = "link", "gio";
+				clocks = <&sys_clk 29>, <&sys_clk 12>;
+				reset-names = "link", "gio", "phy",
+					      "pm", "tx", "rx";
+				resets = <&sys_rst 29>, <&sys_rst 12>,
+					 <&sys_rst 30>,
+					 <&ahci1_rst 0>, <&ahci1_rst 1>,
+					 <&ahci1_rst 2>;
+				#phy-cells = <0>;
+			};
+		};
+
 		usb0: usb@65a00000 {
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
 			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -508,9 +630,10 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-pro4-dwc3-glue",
 				     "simple-mfd";
+			reg = <0x65b00000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x65b00000 0x100>;
@@ -524,7 +647,7 @@
 				resets = <&sys_rst 12>, <&sys_rst 14>;
 			};
 
-			usb0_ssphy: ss-phy@10 {
+			usb0_ssphy: phy@10 {
 				compatible = "socionext,uniphier-pro4-usb3-ssphy";
 				reg = <0x10 0x10>;
 				#phy-cells = <0>;
@@ -535,7 +658,7 @@
 				vbus-supply = <&usb0_vbus>;
 			};
 
-			usb0_rst: reset@40 {
+			usb0_rst: reset-controller@40 {
 				compatible = "socionext,uniphier-pro4-usb3-reset";
 				reg = <0x40 0x4>;
 				#reset-cells = <1>;
@@ -551,7 +674,8 @@
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
 			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -561,9 +685,10 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65d00000 {
+		usb-controller@65d00000 {
 			compatible = "socionext,uniphier-pro4-dwc3-glue",
 				     "simple-mfd";
+			reg = <0x65d00000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x65d00000 0x100>;
@@ -577,7 +702,7 @@
 				resets = <&sys_rst 12>, <&sys_rst 15>;
 			};
 
-			usb1_rst: reset@40 {
+			usb1_rst: reset-controller@40 {
 				compatible = "socionext,uniphier-pro4-usb3-reset";
 				reg = <0x40 0x4>;
 				#reset-cells = <1>;
@@ -588,19 +713,20 @@
 			};
 		};
 
-		nand: nand@68000000 {
+		nand: nand-controller@68000000 {
 			compatible = "socionext,uniphier-denali-nand-v5a";
 			status = "disabled";
 			reg-names = "nand_data", "denali_reg";
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
 			clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>;
-			resets = <&sys_rst 2>;
+			reset-names = "nand", "reg";
+			resets = <&sys_rst 2>, <&sys_rst 2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/socionext/uniphier-pro5-epcore.dts b/arch/arm/boot/dts/socionext/uniphier-pro5-epcore.dts
new file mode 100644
index 000000000000..ed759dcc3216
--- /dev/null
+++ b/arch/arm/boot/dts/socionext/uniphier-pro5-epcore.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Source for UniPhier Pro5 EP-CORE Board (Pro5-PCIe_EP-CORE)
+ *
+ * Copyright (C) 2021 Socionext Inc.
+ *   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+ */
+
+/dts-v1/;
+#include "uniphier-pro5.dtsi"
+#include "uniphier-support-card.dtsi"
+
+/ {
+	model = "UniPhier Pro5 EP-CORE Board";
+	compatible = "socionext,uniphier-pro5-epcore", "socionext,uniphier-pro5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		i2c0 = &i2c0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&ethsc {
+	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&serialsc {
+	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+};
+
+&sd {
+	status = "okay";
+};
+
+&pcie_ep {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/socionext/uniphier-pro5-proex.dts b/arch/arm/boot/dts/socionext/uniphier-pro5-proex.dts
new file mode 100644
index 000000000000..2cfb84f73cc0
--- /dev/null
+++ b/arch/arm/boot/dts/socionext/uniphier-pro5-proex.dts
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Source for UniPhier Pro5 ProEX Board
+ *
+ * Copyright (C) 2021 Socionext Inc.
+ *   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+ */
+
+/dts-v1/;
+#include "uniphier-pro5.dtsi"
+
+/ {
+	model = "UniPhier Pro5 ProEX Board";
+	compatible = "socionext,uniphier-pro5-proex", "socionext,uniphier-pro5";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	aliases {
+		serial1 = &serial1;
+		serial2 = &serial2;
+		i2c0 = &i2c0;
+		i2c1 = &i2c3;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+};
+
+&pcie_ep {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pro5.dtsi b/arch/arm/boot/dts/socionext/uniphier-pro5.dtsi
index eff74717b37c..2d8591cdddb8 100644
--- a/arch/arm/boot/dts/uniphier-pro5.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-pro5.dtsi
@@ -5,6 +5,8 @@
 // Copyright (C) 2015-2016 Socionext Inc.
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
 / {
 	compatible = "socionext,uniphier-pro5";
 	#address-cells = <1>;
@@ -131,11 +133,12 @@
 		ranges;
 		interrupt-parent = <&intc>;
 
-		l2: l2-cache@500c0000 {
+		l2: cache-controller@500c0000 {
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x8>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 190 4>, <0 191 4>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(2 * 1024 * 1024)>;
 			cache-sets = <512>;
@@ -144,11 +147,12 @@
 			next-level-cache = <&l3>;
 		};
 
-		l3: l3-cache@500c8000 {
+		l3: cache-controller@500c8000 {
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c8000 0x2000>, <0x503c8100 0x8>,
 			      <0x506c8000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(2 * 1024 * 1024)>;
 			cache-sets = <512>;
@@ -160,7 +164,9 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006000 0x100>;
-			interrupts = <0 39 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -171,18 +177,20 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006100 0x100>;
-			interrupts = <0 216 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
-			clocks = <&peri_clk 11>;
-			resets = <&peri_rst 11>;
+			clocks = <&peri_clk 11>;	/* common with spi0 */
+			resets = <&peri_rst 12>;
 		};
 
 		serial0: serial@54006800 {
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -193,7 +201,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -204,7 +212,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -215,7 +223,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -242,7 +250,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -256,7 +264,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -270,7 +278,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -284,7 +292,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -300,7 +308,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -312,7 +320,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -333,39 +341,39 @@
 			reg = <0x59801000 0x400>;
 		};
 
-		sdctrl@59810000 {
+		sdctrl: syscon@59810000 {
 			compatible = "socionext,uniphier-pro5-sdctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59810000 0x400>;
 
-			sd_clk: clock {
+			sd_clk: clock-controller {
 				compatible = "socionext,uniphier-pro5-sd-clock";
 				#clock-cells = <1>;
 			};
 
-			sd_rst: reset {
+			sd_rst: reset-controller {
 				compatible = "socionext,uniphier-pro5-sd-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		perictrl@59820000 {
+		syscon@59820000 {
 			compatible = "socionext,uniphier-pro5-perictrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59820000 0x200>;
 
-			peri_clk: clock {
+			peri_clk: clock-controller {
 				compatible = "socionext,uniphier-pro5-peri-clock";
 				#clock-cells = <1>;
 			};
 
-			peri_rst: reset {
+			peri_rst: reset-controller {
 				compatible = "socionext,uniphier-pro5-peri-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		soc-glue@5f800000 {
+		syscon@5f800000 {
 			compatible = "socionext,uniphier-pro5-soc-glue",
 				     "simple-mfd", "syscon";
 			reg = <0x5f800000 0x2000>;
@@ -375,9 +383,10 @@
 			};
 		};
 
-		soc-glue@5f900000 {
+		syscon@5f900000 {
 			compatible = "socionext,uniphier-pro5-soc-glue-debug",
-				     "simple-mfd";
+				     "simple-mfd", "syscon";
+			reg = <0x5f900000 0x2000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x5f900000 0x2000>;
@@ -408,7 +417,15 @@
 			};
 		};
 
-		aidet: aidet@5fc20000 {
+		xdmac: dma-controller@5fc10000 {
+			compatible = "socionext,uniphier-xdmac";
+			reg = <0x5fc10000 0x5300>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <2>;
+		};
+
+		aidet: interrupt-controller@5fc20000 {
 			compatible = "socionext,uniphier-pro5-aidet";
 			reg = <0x5fc20000 0x200>;
 			interrupt-controller;
@@ -418,14 +435,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x304>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x304>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -437,42 +456,222 @@
 			interrupt-controller;
 		};
 
-		sysctrl@61840000 {
+		syscon@61840000 {
 			compatible = "socionext,uniphier-pro5-sysctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x61840000 0x10000>;
 
-			sys_clk: clock {
+			sys_clk: clock-controller {
 				compatible = "socionext,uniphier-pro5-clock";
 				#clock-cells = <1>;
 			};
 
-			sys_rst: reset {
+			sys_rst: reset-controller {
 				compatible = "socionext,uniphier-pro5-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		nand: nand@68000000 {
+		usb0: usb@65a00000 {
+			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+			status = "disabled";
+			reg = <0x65a00000 0xcd00>;
+			interrupt-names = "host";
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb0>;
+			clock-names = "ref", "bus_early", "suspend";
+			clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+			resets = <&usb0_rst 15>;
+			phys = <&usb0_hsphy0>, <&usb0_ssphy0>;
+			dr_mode = "host";
+		};
+
+		usb-controller@65b00000 {
+			compatible = "socionext,uniphier-pro5-dwc3-glue",
+				     "simple-mfd";
+			reg = <0x65b00000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65b00000 0x400>;
+
+			usb0_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pro5-usb3-reset";
+				reg = <0x0 0x4>;
+				#reset-cells = <1>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 14>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 14>;
+			};
+
+			usb0_vbus0: regulator@100 {
+				compatible = "socionext,uniphier-pro5-usb3-regulator";
+				reg = <0x100 0x10>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 14>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 14>;
+			};
+
+			usb0_hsphy0: phy@280 {
+				compatible = "socionext,uniphier-pro5-usb3-hsphy";
+				reg = <0x280 0x10>;
+				#phy-cells = <0>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 14>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 14>;
+				vbus-supply = <&usb0_vbus0>;
+			};
+
+			usb0_ssphy0: phy@380 {
+				compatible = "socionext,uniphier-pro5-usb3-ssphy";
+				reg = <0x380 0x10>;
+				#phy-cells = <0>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 14>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 14>;
+				vbus-supply = <&usb0_vbus0>;
+			};
+		};
+
+		usb1: usb@65c00000 {
+			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+			status = "disabled";
+			reg = <0x65c00000 0xcd00>;
+			interrupt-names = "host";
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb2>;
+			clock-names = "ref", "bus_early", "suspend";
+			clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+			resets = <&usb1_rst 15>;
+			phys = <&usb1_hsphy0>, <&usb1_hsphy1>, <&usb1_ssphy0>;
+			dr_mode = "host";
+		};
+
+		usb-controller@65d00000 {
+			compatible = "socionext,uniphier-pro5-dwc3-glue",
+				     "simple-mfd";
+			reg = <0x65d00000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65d00000 0x400>;
+
+			usb1_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pro5-usb3-reset";
+				reg = <0x0 0x4>;
+				#reset-cells = <1>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 15>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 15>;
+			};
+
+			usb1_vbus0: regulator@100 {
+				compatible = "socionext,uniphier-pro5-usb3-regulator";
+				reg = <0x100 0x10>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 15>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 15>;
+			};
+
+			usb1_vbus1: regulator@110 {
+				compatible = "socionext,uniphier-pro5-usb3-regulator";
+				reg = <0x110 0x10>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 15>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 15>;
+			};
+
+			usb1_hsphy0: phy@280 {
+				compatible = "socionext,uniphier-pro5-usb3-hsphy";
+				reg = <0x280 0x10>;
+				#phy-cells = <0>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 15>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 15>;
+				vbus-supply = <&usb1_vbus0>;
+			};
+
+			usb1_hsphy1: phy@290 {
+				compatible = "socionext,uniphier-pro5-usb3-hsphy";
+				reg = <0x290 0x10>;
+				#phy-cells = <0>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 15>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 15>;
+				vbus-supply = <&usb1_vbus1>;
+			};
+
+			usb1_ssphy0: phy@380 {
+				compatible = "socionext,uniphier-pro5-usb3-ssphy";
+				reg = <0x380 0x10>;
+				#phy-cells = <0>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 15>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 15>;
+				vbus-supply = <&usb1_vbus0>;
+			};
+		};
+
+		pcie_ep: pcie-ep@66000000 {
+			compatible = "socionext,uniphier-pro5-pcie-ep";
+			status = "disabled";
+			reg-names = "dbi", "dbi2", "link", "addr_space";
+			reg = <0x66000000 0x1000>, <0x66001000 0x1000>,
+			      <0x66010000 0x10000>, <0x67000000 0x400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pcie>;
+			clock-names = "gio", "link";
+			clocks = <&sys_clk 12>, <&sys_clk 24>;
+			reset-names = "gio", "link";
+			resets = <&sys_rst 12>, <&sys_rst 24>;
+			num-ib-windows = <16>;
+			num-ob-windows = <16>;
+			num-lanes = <4>;
+			phy-names = "pcie-phy";
+			phys = <&pcie_phy>;
+		};
+
+		pcie_phy: phy@66038000 {
+			compatible = "socionext,uniphier-pro5-pcie-phy";
+			reg = <0x66038000 0x4000>;
+			#phy-cells = <0>;
+			clock-names = "gio", "link";
+			clocks = <&sys_clk 12>, <&sys_clk 24>;
+			reset-names = "gio", "link";
+			resets = <&sys_rst 12>, <&sys_rst 24>;
+		};
+
+		nand: nand-controller@68000000 {
 			compatible = "socionext,uniphier-denali-nand-v5b";
 			status = "disabled";
 			reg-names = "nand_data", "denali_reg";
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
 			clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>;
-			resets = <&sys_rst 2>;
+			reset-names = "nand", "reg";
+			resets = <&sys_rst 2>, <&sys_rst 2>;
 		};
 
-		emmc: sdhc@68400000 {
+		emmc: mmc@68400000 {
 			compatible = "socionext,uniphier-sd-v3.1";
 			status = "disabled";
 			reg = <0x68400000 0x800>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sd_clk 1>;
@@ -484,11 +683,11 @@
 			non-removable;
 		};
 
-		sd: sdhc@68800000 {
+		sd: mmc@68800000 {
 			compatible = "socionext,uniphier-sd-v3.1";
 			status = "disabled";
 			reg = <0x68800000 0x800>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -500,6 +699,7 @@
 			sd-uhs-sdr12;
 			sd-uhs-sdr25;
 			sd-uhs-sdr50;
+			socionext,syscon-uhs-mode = <&sdctrl 0>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts b/arch/arm/boot/dts/socionext/uniphier-pxs2-gentil.dts
index e27fd4f2a569..5f18b926c50a 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-pxs2-gentil.dts
@@ -26,6 +26,7 @@
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &eth;
 	};
 
 	memory@80000000 {
@@ -86,7 +87,7 @@
 };
 
 &mdio {
-	ethphy: ethphy@1 {
+	ethphy: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
@@ -98,3 +99,7 @@
 &usb1 {
 	status = "okay";
 };
+
+&ahci {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pxs2-vodka.dts b/arch/arm/boot/dts/socionext/uniphier-pxs2-vodka.dts
index 23fe42b7408b..7e08a459f7d8 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-pxs2-vodka.dts
@@ -24,6 +24,7 @@
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &eth;
 	};
 
 	memory@80000000 {
@@ -87,7 +88,7 @@
 };
 
 &mdio {
-	ethphy: ethphy@1 {
+	ethphy: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/socionext/uniphier-pxs2.dtsi
index 4eddbb8d7fca..f97a57222101 100644
--- a/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-pxs2.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -157,11 +158,14 @@
 		ranges;
 		interrupt-parent = <&intc>;
 
-		l2: l2-cache@500c0000 {
+		l2: cache-controller@500c0000 {
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x8>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>, <0 190 4>, <0 191 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(1280 * 1024)>;
 			cache-sets = <512>;
@@ -173,7 +177,9 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006000 0x100>;
-			interrupts = <0 39 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -184,18 +190,20 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006100 0x100>;
-			interrupts = <0 216 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
-			clocks = <&peri_clk 11>;
-			resets = <&peri_rst 11>;
+			clocks = <&peri_clk 12>;
+			resets = <&peri_rst 12>;
 		};
 
 		serial0: serial@54006800 {
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -206,7 +214,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -217,7 +225,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -228,7 +236,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -255,7 +263,7 @@
 		audio@56000000 {
 			compatible = "socionext,uniphier-pxs2-aio";
 			reg = <0x56000000 0x80000>;
-			interrupts = <0 144 4>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ain1>,
 				    <&pinctrl_ain2>,
@@ -313,7 +321,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -327,7 +335,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -341,7 +349,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -355,7 +363,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -369,7 +377,7 @@
 			reg = <0x58784000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 45 4>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 8>;
 			resets = <&peri_rst 8>;
 			clock-frequency = <400000>;
@@ -381,7 +389,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -393,7 +401,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -414,43 +422,43 @@
 			reg = <0x59801000 0x400>;
 		};
 
-		sdctrl@59810000 {
+		sdctrl: syscon@59810000 {
 			compatible = "socionext,uniphier-pxs2-sdctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59810000 0x400>;
 
-			sd_clk: clock {
+			sd_clk: clock-controller {
 				compatible = "socionext,uniphier-pxs2-sd-clock";
 				#clock-cells = <1>;
 			};
 
-			sd_rst: reset {
+			sd_rst: reset-controller {
 				compatible = "socionext,uniphier-pxs2-sd-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		perictrl@59820000 {
+		syscon@59820000 {
 			compatible = "socionext,uniphier-pxs2-perictrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59820000 0x200>;
 
-			peri_clk: clock {
+			peri_clk: clock-controller {
 				compatible = "socionext,uniphier-pxs2-peri-clock";
 				#clock-cells = <1>;
 			};
 
-			peri_rst: reset {
+			peri_rst: reset-controller {
 				compatible = "socionext,uniphier-pxs2-peri-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		emmc: sdhc@5a000000 {
+		emmc: mmc@5a000000 {
 			compatible = "socionext,uniphier-sd-v3.1.1";
 			status = "disabled";
 			reg = <0x5a000000 0x800>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sd_clk 1>;
@@ -462,11 +470,11 @@
 			non-removable;
 		};
 
-		sd: sdhc@5a400000 {
+		sd: mmc@5a400000 {
 			compatible = "socionext,uniphier-sd-v3.1.1";
 			status = "disabled";
 			reg = <0x5a400000 0x800>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -478,9 +486,10 @@
 			sd-uhs-sdr12;
 			sd-uhs-sdr25;
 			sd-uhs-sdr50;
+			socionext,syscon-uhs-mode = <&sdctrl 0>;
 		};
 
-		soc_glue: soc-glue@5f800000 {
+		soc_glue: syscon@5f800000 {
 			compatible = "socionext,uniphier-pxs2-soc-glue",
 				     "simple-mfd", "syscon";
 			reg = <0x5f800000 0x2000>;
@@ -490,9 +499,10 @@
 			};
 		};
 
-		soc-glue@5f900000 {
+		syscon@5f900000 {
 			compatible = "socionext,uniphier-pxs2-soc-glue-debug",
-				     "simple-mfd";
+				     "simple-mfd", "syscon";
+			reg = <0x5f900000 0x2000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x5f900000 0x2000>;
@@ -508,7 +518,15 @@
 			};
 		};
 
-		aidet: aidet@5fc20000 {
+		xdmac: dma-controller@5fc10000 {
+			compatible = "socionext,uniphier-xdmac";
+			reg = <0x5fc10000 0x5300>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <2>;
+		};
+
+		aidet: interrupt-controller@5fc20000 {
 			compatible = "socionext,uniphier-pxs2-aidet";
 			reg = <0x5fc20000 0x200>;
 			interrupt-controller;
@@ -518,14 +536,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0xf04>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(0xf) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0xf04>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(0xf) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -537,24 +557,24 @@
 			interrupt-controller;
 		};
 
-		sysctrl@61840000 {
+		syscon@61840000 {
 			compatible = "socionext,uniphier-pxs2-sysctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x61840000 0x10000>;
 
-			sys_clk: clock {
+			sys_clk: clock-controller {
 				compatible = "socionext,uniphier-pxs2-clock";
 				#clock-cells = <1>;
 			};
 
-			sys_rst: reset {
+			sys_rst: reset-controller {
 				compatible = "socionext,uniphier-pxs2-reset";
 				#reset-cells = <1>;
 			};
 
-			pvtctl: pvtctl {
+			pvtctl: thermal-sensor {
 				compatible = "socionext,uniphier-pxs2-thermal";
-				interrupts = <0 3 4>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 				#thermal-sensor-cells = <0>;
 				socionext,tmod-calibration = <0x0f86 0x6844>;
 			};
@@ -564,14 +584,14 @@
 			compatible = "socionext,uniphier-pxs2-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether_rgmii>;
 			clock-names = "ether";
 			clocks = <&sys_clk 6>;
 			reset-names = "ether";
 			resets = <&sys_rst 6>;
-			phy-mode = "rgmii";
+			phy-mode = "rgmii-id";
 			local-mac-address = [00 00 00 00 00 00];
 			socionext,syscon-phy-mode = <&soc_glue 0>;
 
@@ -581,12 +601,53 @@
 			};
 		};
 
+		ahci: sata@65600000 {
+			compatible = "socionext,uniphier-pxs2-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65600000 0x10000>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 28>;
+			resets = <&sys_rst 28>, <&ahci_rst 0>;
+			ports-implemented = <1>;
+			phys = <&ahci_phy>;
+		};
+
+		sata-controller@65700000 {
+			compatible = "socionext,uniphier-pxs2-ahci-glue",
+				     "simple-mfd";
+			reg = <0x65700000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65700000 0x100>;
+
+			ahci_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pxs2-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "link";
+				clocks = <&sys_clk 28>;
+				reset-names = "link";
+				resets = <&sys_rst 28>;
+				#reset-cells = <1>;
+			};
+
+			ahci_phy: phy@10 {
+				compatible = "socionext,uniphier-pxs2-ahci-phy";
+				reg = <0x10 0x10>;
+				clock-names = "link";
+				clocks = <&sys_clk 28>;
+				reset-names = "link", "phy";
+				resets = <&sys_rst 28>, <&sys_rst 30>;
+				#phy-cells = <0>;
+			};
+		};
+
 		usb0: usb@65a00000 {
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -597,14 +658,15 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-pxs2-dwc3-glue",
 				     "simple-mfd";
+			reg = <0x65b00000 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x65b00000 0x400>;
 
-			usb0_rst: reset@0 {
+			usb0_rst: reset-controller@0 {
 				compatible = "socionext,uniphier-pxs2-usb3-reset";
 				reg = <0x0 0x4>;
 				#reset-cells = <1>;
@@ -632,7 +694,7 @@
 				resets = <&sys_rst 14>;
 			};
 
-			usb0_hsphy0: hs-phy@200 {
+			usb0_hsphy0: phy@200 {
 				compatible = "socionext,uniphier-pxs2-usb3-hsphy";
 				reg = <0x200 0x10>;
 				#phy-cells = <0>;
@@ -643,7 +705,7 @@
 				vbus-supply = <&usb0_vbus0>;
 			};
 
-			usb0_hsphy1: hs-phy@210 {
+			usb0_hsphy1: phy@210 {
 				compatible = "socionext,uniphier-pxs2-usb3-hsphy";
 				reg = <0x210 0x10>;
 				#phy-cells = <0>;
@@ -654,7 +716,7 @@
 				vbus-supply = <&usb0_vbus1>;
 			};
 
-			usb0_ssphy0: ss-phy@300 {
+			usb0_ssphy0: phy@300 {
 				compatible = "socionext,uniphier-pxs2-usb3-ssphy";
 				reg = <0x300 0x10>;
 				#phy-cells = <0>;
@@ -665,7 +727,7 @@
 				vbus-supply = <&usb0_vbus0>;
 			};
 
-			usb0_ssphy1: ss-phy@310 {
+			usb0_ssphy1: phy@310 {
 				compatible = "socionext,uniphier-pxs2-usb3-ssphy";
 				reg = <0x310 0x10>;
 				#phy-cells = <0>;
@@ -681,8 +743,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -692,14 +754,15 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65d00000 {
+		usb-controller@65d00000 {
 			compatible = "socionext,uniphier-pxs2-dwc3-glue",
 				     "simple-mfd";
+			reg = <0x65d00000 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x65d00000 0x400>;
 
-			usb1_rst: reset@0 {
+			usb1_rst: reset-controller@0 {
 				compatible = "socionext,uniphier-pxs2-usb3-reset";
 				reg = <0x0 0x4>;
 				#reset-cells = <1>;
@@ -727,7 +790,7 @@
 				resets = <&sys_rst 15>;
 			};
 
-			usb1_hsphy0: hs-phy@200 {
+			usb1_hsphy0: phy@200 {
 				compatible = "socionext,uniphier-pxs2-usb3-hsphy";
 				reg = <0x200 0x10>;
 				#phy-cells = <0>;
@@ -738,7 +801,7 @@
 				vbus-supply = <&usb1_vbus0>;
 			};
 
-			usb1_hsphy1: hs-phy@210 {
+			usb1_hsphy1: phy@210 {
 				compatible = "socionext,uniphier-pxs2-usb3-hsphy";
 				reg = <0x210 0x10>;
 				#phy-cells = <0>;
@@ -749,7 +812,7 @@
 				vbus-supply = <&usb1_vbus1>;
 			};
 
-			usb1_ssphy0: ss-phy@300 {
+			usb1_ssphy0: phy@300 {
 				compatible = "socionext,uniphier-pxs2-usb3-ssphy";
 				reg = <0x300 0x10>;
 				#phy-cells = <0>;
@@ -761,19 +824,20 @@
 			};
 		};
 
-		nand: nand@68000000 {
+		nand: nand-controller@68000000 {
 			compatible = "socionext,uniphier-denali-nand-v5b";
 			status = "disabled";
 			reg-names = "nand_data", "denali_reg";
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
 			clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>;
-			resets = <&sys_rst 2>;
+			reset-names = "nand", "reg";
+			resets = <&sys_rst 2>, <&sys_rst 2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/uniphier-ref-daughter.dtsi b/arch/arm/boot/dts/socionext/uniphier-ref-daughter.dtsi
index 04e60c295319..a11897669c26 100644
--- a/arch/arm/boot/dts/uniphier-ref-daughter.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-ref-daughter.dtsi
@@ -7,7 +7,7 @@
 
 &i2c0 {
 	eeprom@50 {
-		compatible = "microchip,24lc128";
+		compatible = "microchip,24lc128", "atmel,24c128";
 		reg = <0x50>;
 		pagesize = <64>;
 	};
diff --git a/arch/arm/boot/dts/uniphier-sld8-ref.dts b/arch/arm/boot/dts/socionext/uniphier-sld8-ref.dts
index cf9ea0b15065..2446f9e15360 100644
--- a/arch/arm/boot/dts/uniphier-sld8-ref.dts
+++ b/arch/arm/boot/dts/socionext/uniphier-sld8-ref.dts
@@ -20,7 +20,7 @@
 
 	aliases {
 		serial0 = &serial0;
-		serial1 = &serial1;
+		serial1 = &serialsc;
 		serial2 = &serial2;
 		serial3 = &serial3;
 		i2c0 = &i2c0;
@@ -36,7 +36,11 @@
 };
 
 &ethsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&serialsc {
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -52,7 +56,7 @@
 };
 
 &gpio {
-	xirq0 {
+	xirq0-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(0) 0>;
 		input;
diff --git a/arch/arm/boot/dts/uniphier-sld8.dtsi b/arch/arm/boot/dts/socionext/uniphier-sld8.dtsi
index cbebb6e4c616..f876282760e9 100644
--- a/arch/arm/boot/dts/uniphier-sld8.dtsi
+++ b/arch/arm/boot/dts/socionext/uniphier-sld8.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-sld8";
@@ -51,11 +52,12 @@
 		ranges;
 		interrupt-parent = <&intc>;
 
-		l2: l2-cache@500c0000 {
+		l2: cache-controller@500c0000 {
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x4>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(256 * 1024)>;
 			cache-sets = <256>;
@@ -67,7 +69,9 @@
 			compatible = "socionext,uniphier-scssi";
 			status = "disabled";
 			reg = <0x54006000 0x100>;
-			interrupts = <0 39 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -78,7 +82,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -89,7 +93,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -100,7 +104,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -111,7 +115,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 29 4>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -142,7 +146,7 @@
 			reg = <0x58400000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 1>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -156,7 +160,7 @@
 			reg = <0x58480000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 1>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -170,7 +174,7 @@
 			reg = <0x58500000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 1>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -184,7 +188,7 @@
 			reg = <0x58580000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 1>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -207,33 +211,33 @@
 			reg = <0x59801000 0x400>;
 		};
 
-		mioctrl@59810000 {
+		mioctrl: syscon@59810000 {
 			compatible = "socionext,uniphier-sld8-mioctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59810000 0x800>;
 
-			mio_clk: clock {
+			mio_clk: clock-controller {
 				compatible = "socionext,uniphier-sld8-mio-clock";
 				#clock-cells = <1>;
 			};
 
-			mio_rst: reset {
+			mio_rst: reset-controller {
 				compatible = "socionext,uniphier-sld8-mio-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		perictrl@59820000 {
+		syscon@59820000 {
 			compatible = "socionext,uniphier-sld8-perictrl",
 				     "simple-mfd", "syscon";
 			reg = <0x59820000 0x200>;
 
-			peri_clk: clock {
+			peri_clk: clock-controller {
 				compatible = "socionext,uniphier-sld8-peri-clock";
 				#clock-cells = <1>;
 			};
 
-			peri_rst: reset {
+			peri_rst: reset-controller {
 				compatible = "socionext,uniphier-sld8-peri-reset";
 				#reset-cells = <1>;
 			};
@@ -242,18 +246,23 @@
 		dmac: dma-controller@5a000000 {
 			compatible = "socionext,uniphier-mio-dmac";
 			reg = <0x5a000000 0x1000>;
-			interrupts = <0 68 4>, <0 68 4>, <0 69 4>, <0 70 4>,
-				     <0 71 4>, <0 72 4>, <0 73 4>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mio_clk 7>;
 			resets = <&mio_rst 7>;
 			#dma-cells = <1>;
 		};
 
-		sd: sdhc@5a400000 {
+		sd: mmc@5a400000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a400000 0x200>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -267,13 +276,14 @@
 			sd-uhs-sdr12;
 			sd-uhs-sdr25;
 			sd-uhs-sdr50;
+			socionext,syscon-uhs-mode = <&mioctrl 0>;
 		};
 
-		emmc: sdhc@5a500000 {
+		emmc: mmc@5a500000 {
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a500000 0x200>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&mio_clk 1>;
@@ -291,7 +301,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 80 4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -305,7 +315,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 81 4>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -319,7 +329,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a820100 0x100>;
-			interrupts = <0 82 4>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 10>,
@@ -329,7 +339,7 @@
 			has-transaction-translator;
 		};
 
-		soc-glue@5f800000 {
+		syscon@5f800000 {
 			compatible = "socionext,uniphier-sld8-soc-glue",
 				     "simple-mfd", "syscon";
 			reg = <0x5f800000 0x2000>;
@@ -339,9 +349,10 @@
 			};
 		};
 
-		soc-glue@5f900000 {
+		syscon@5f900000 {
 			compatible = "socionext,uniphier-sld8-soc-glue-debug",
-				     "simple-mfd";
+				     "simple-mfd", "syscon";
+			reg = <0x5f900000 0x2000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x5f900000 0x2000>;
@@ -360,14 +371,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x104>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x104>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -379,42 +392,43 @@
 			interrupt-controller;
 		};
 
-		aidet: aidet@61830000 {
+		aidet: interrupt-controller@61830000 {
 			compatible = "socionext,uniphier-sld8-aidet";
 			reg = <0x61830000 0x200>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
 
-		sysctrl@61840000 {
+		syscon@61840000 {
 			compatible = "socionext,uniphier-sld8-sysctrl",
 				     "simple-mfd", "syscon";
 			reg = <0x61840000 0x10000>;
 
-			sys_clk: clock {
+			sys_clk: clock-controller {
 				compatible = "socionext,uniphier-sld8-clock";
 				#clock-cells = <1>;
 			};
 
-			sys_rst: reset {
+			sys_rst: reset-controller {
 				compatible = "socionext,uniphier-sld8-reset";
 				#reset-cells = <1>;
 			};
 		};
 
-		nand: nand@68000000 {
+		nand: nand-controller@68000000 {
 			compatible = "socionext,uniphier-denali-nand-v5a";
 			status = "disabled";
 			reg-names = "nand_data", "denali_reg";
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
 			clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>;
-			resets = <&sys_rst 2>;
+			reset-names = "nand", "reg";
+			resets = <&sys_rst 2>, <&sys_rst 2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/socionext/uniphier-support-card.dtsi b/arch/arm/boot/dts/socionext/uniphier-support-card.dtsi
new file mode 100644
index 000000000000..97e7d5db8eb8
--- /dev/null
+++ b/arch/arm/boot/dts/socionext/uniphier-support-card.dtsi
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+//
+// Device Tree Source for UniPhier Support Card (Expansion Board)
+//
+// Copyright (C) 2015-2017 Socionext Inc.
+//   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+
+&system_bus {
+	status = "okay";
+	ranges = <1 0x00000000 0x42000000 0x02000000>;
+
+	ethsc: ethernet@1,1f00000 {
+		compatible = "smsc,lan9118", "smsc,lan9115";
+		reg = <1 0x01f00000 0x1000>;
+		phy-mode = "mii";
+		reg-io-width = <4>;
+		interrupt-parent = <&gpio>;
+	};
+
+	serialsc: serial@1,1fb0000 {
+		compatible = "ns16550a";
+		reg = <1 0x01fb0000 0x20>;
+		clock-frequency = <12288000>;
+		reg-shift = <1>;
+		interrupt-parent = <&gpio>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/Makefile b/arch/arm/boot/dts/st/Makefile
new file mode 100644
index 000000000000..7892ad69b441
--- /dev/null
+++ b/arch/arm/boot/dts/st/Makefile
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NOMADIK) += \
+	ste-nomadik-s8815.dtb \
+	ste-nomadik-nhk15.dtb
+dtb-$(CONFIG_ARCH_SPEAR13XX) += \
+	spear1310-evb.dtb \
+	spear1340-evb.dtb
+dtb-$(CONFIG_ARCH_SPEAR3XX) += \
+	spear300-evb.dtb \
+	spear310-evb.dtb \
+	spear320-evb.dtb \
+	spear320-hmi.dtb
+dtb-$(CONFIG_ARCH_SPEAR6XX) += \
+	spear600-evb.dtb
+dtb-$(CONFIG_ARCH_STI) += \
+	stih407-b2120.dtb \
+	stih410-b2120.dtb \
+	stih410-b2260.dtb \
+	stih418-b2199.dtb \
+	stih418-b2264.dtb
+dtb-$(CONFIG_ARCH_STM32) += \
+	stm32f429-disco.dtb \
+	stm32f469-disco.dtb \
+	stm32f746-disco.dtb \
+	stm32f769-disco.dtb \
+	stm32429i-eval.dtb \
+	stm32746g-eval.dtb \
+	stm32h743i-eval.dtb \
+	stm32h743i-disco.dtb \
+	stm32h750i-art-pi.dtb \
+	stm32mp135f-dk.dtb \
+	stm32mp151a-prtt1a.dtb \
+	stm32mp151a-prtt1c.dtb \
+	stm32mp151a-prtt1s.dtb \
+	stm32mp151a-dhcor-testbench.dtb \
+	stm32mp153c-dhcom-drc02.dtb \
+	stm32mp153c-dhcor-drc-compact.dtb \
+	stm32mp157a-avenger96.dtb \
+	stm32mp157a-dhcor-avenger96.dtb \
+	stm32mp157a-dk1.dtb \
+	stm32mp157a-dk1-scmi.dtb \
+	stm32mp157a-iot-box.dtb \
+	stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
+	stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dtb \
+	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
+	stm32mp157a-icore-stm32mp1-ctouch2-of10.dtb \
+	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
+	stm32mp157a-stinger96.dtb \
+	stm32mp157c-dhcom-pdk2.dtb \
+	stm32mp157c-dhcom-picoitx.dtb \
+	stm32mp157c-dk2.dtb \
+	stm32mp157c-dk2-scmi.dtb \
+	stm32mp157c-ed1.dtb \
+	stm32mp157c-ed1-scmi.dtb \
+	stm32mp157c-emsbc-argon.dtb \
+	stm32mp157c-ev1.dtb \
+	stm32mp157c-ev1-scmi.dtb \
+	stm32mp157c-lxa-mc1.dtb \
+	stm32mp157c-lxa-tac-gen1.dtb \
+	stm32mp157c-lxa-tac-gen2.dtb \
+	stm32mp157c-odyssey.dtb \
+	stm32mp157c-osd32mp1-red.dtb \
+	stm32mp157c-phycore-stm32mp1-3.dtb
+dtb-$(CONFIG_ARCH_U8500) += \
+	ste-snowball.dtb \
+	ste-hrefprev60-stuib.dtb \
+	ste-hrefprev60-tvk.dtb \
+	ste-hrefv60plus-stuib.dtb \
+	ste-hrefv60plus-tvk.dtb \
+	ste-href520-tvk.dtb \
+	ste-ux500-samsung-golden.dtb \
+	ste-ux500-samsung-janice.dtb \
+	ste-ux500-samsung-gavini.dtb \
+	ste-ux500-samsung-codina.dtb \
+	ste-ux500-samsung-codina-tmo.dtb \
+	ste-ux500-samsung-skomer.dtb \
+	ste-ux500-samsung-kyle.dtb
diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/st/spear1310-evb.dts
index 8fcb6be6e7c7..18191a87f07c 100644
--- a/arch/arm/boot/dts/spear1310-evb.dts
+++ b/arch/arm/boot/dts/st/spear1310-evb.dts
@@ -170,7 +170,7 @@
 
 		smi: flash@ea000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@e6000000 {
 				#address-cells = <1>;
@@ -352,7 +352,6 @@
 					#size-cells = <0>;
 					spi-max-frequency = <1000000>;
 					spi-cpha;
-					pl022,hierarchy = <0>;
 					pl022,interface = <0>;
 					pl022,slave-tx-disable;
 					pl022,com-mode = <0>;
@@ -379,29 +378,12 @@
 					};
 				};
 
-				m25p80@1 {
+				flash@1 {
 					compatible = "st,m25p80";
 					reg = <1>;
 					spi-max-frequency = <12000000>;
 					spi-cpol;
 					spi-cpha;
-					pl022,hierarchy = <0>;
-					pl022,interface = <0>;
-					pl022,slave-tx-disable;
-					pl022,com-mode = <0x2>;
-					pl022,rx-level-trig = <0>;
-					pl022,tx-level-trig = <0>;
-					pl022,ctrl-len = <0x11>;
-					pl022,wait-state = <0>;
-					pl022,duplex = <0>;
-				};
-
-				spidev@2 {
-					compatible = "spidev";
-					reg = <2>;
-					spi-max-frequency = <25000000>;
-					spi-cpha;
-					pl022,hierarchy = <0>;
 					pl022,interface = <0>;
 					pl022,slave-tx-disable;
 					pl022,com-mode = <0x2>;
diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/st/spear1310.dtsi
index c4b49baf9804..ba827d60bf07 100644
--- a/arch/arm/boot/dts/spear1310.dtsi
+++ b/arch/arm/boot/dts/st/spear1310.dtsi
@@ -11,7 +11,7 @@
 	compatible = "st,spear1310";
 
 	ahb {
-		spics: spics@e0700000{
+		spics: spics@e0700000 {
 			compatible = "st,spear-spics-gpio";
 			reg = <0xe0700000 0x1000>;
 			st-spics,peripcfg-reg = <0x3b0>;
@@ -82,8 +82,6 @@
 			reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
 			reg-names = "dbi", "config";
 			interrupts = <0 68 0x4>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0x0 0 &gic 0 68 0x4>;
 			num-lanes = <1>;
 			phys = <&miphy0 1>;
 			phy-names = "pcie-phy";
@@ -101,8 +99,6 @@
 			reg = <0xb1800000 0x4000>, <0x90000000 0x20000>;
 			reg-names = "dbi", "config";
 			interrupts = <0 69 0x4>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0x0 0 &gic 0 69 0x4>;
 			num-lanes = <1>;
 			phys = <&miphy1 1>;
 			phy-names = "pcie-phy";
@@ -120,8 +116,6 @@
 			reg = <0xb4000000 0x4000>, <0xc0000000 0x20000>;
 			reg-names = "dbi", "config";
 			interrupts = <0 70 0x4>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0x0 0 &gic 0 70 0x4>;
 			num-lanes = <1>;
 			phys = <&miphy2 1>;
 			phy-names = "pcie-phy";
diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/st/spear1340-evb.dts
index f70ff56d4542..cea624fc745c 100644
--- a/arch/arm/boot/dts/spear1340-evb.dts
+++ b/arch/arm/boot/dts/st/spear1340-evb.dts
@@ -168,7 +168,7 @@
 
 		smi: flash@ea000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@e6000000 {
 				#address-cells = <1>;
@@ -439,13 +439,12 @@
 				cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>,
 					   <&gpiopinctrl 85 0>;
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "m25p80";
 					reg = <0>;
 					spi-max-frequency = <12000000>;
 					spi-cpol;
 					spi-cpha;
-					pl022,hierarchy = <0>;
 					pl022,interface = <0>;
 					pl022,slave-tx-disable;
 					pl022,com-mode = <0x2>;
@@ -461,7 +460,6 @@
 					spi-max-frequency = <1000000>;
 					spi-cpha;
 					reg = <1>;
-					pl022,hierarchy = <0>;
 					pl022,interface = <0>;
 					pl022,slave-tx-disable;
 					pl022,com-mode = <0>;
@@ -489,22 +487,6 @@
 						ts,i-drive = <1>;
 					};
 				};
-
-				spidev@2 {
-					compatible = "spidev";
-					reg = <2>;
-					spi-max-frequency = <25000000>;
-					spi-cpha;
-					pl022,hierarchy = <0>;
-					pl022,interface = <0>;
-					pl022,slave-tx-disable;
-					pl022,com-mode = <0x2>;
-					pl022,rx-level-trig = <0>;
-					pl022,tx-level-trig = <0>;
-					pl022,ctrl-len = <0x11>;
-					pl022,wait-state = <0>;
-					pl022,duplex = <0>;
-				};
 			};
 
 			timer@ec800600 {
diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/st/spear1340.dtsi
index 1a8f5e8b10e3..51f6ffd08b42 100644
--- a/arch/arm/boot/dts/spear1340.dtsi
+++ b/arch/arm/boot/dts/st/spear1340.dtsi
@@ -12,7 +12,7 @@
 
 	ahb {
 
-		spics: spics@e0700000{
+		spics: spics@e0700000 {
 			compatible = "st,spear-spics-gpio";
 			reg = <0xe0700000 0x1000>;
 			st-spics,peripcfg-reg = <0x42c>;
@@ -47,8 +47,6 @@
 			reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
 			reg-names = "dbi", "config";
 			interrupts = <0 68 0x4>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0x0 0 &gic 0 68 0x4>;
 			num-lanes = <1>;
 			phys = <&miphy0 1>;
 			phy-names = "pcie-phy";
@@ -65,8 +63,8 @@
 			compatible = "snps,designware-i2s";
 			reg = <0xb2400000 0x10000>;
 			interrupt-names = "play_irq";
-			interrupts = <0 98 0x4
-				      0 99 0x4>;
+			interrupts = <0 98 0x4>,
+				     <0 99 0x4>;
 			play;
 			channel = <8>;
 			status = "disabled";
@@ -76,8 +74,8 @@
 			compatible = "snps,designware-i2s";
 			reg = <0xb2000000 0x10000>;
 			interrupt-names = "record_irq";
-			interrupts = <0 100  0x4
-				      0 101 0x4>;
+			interrupts = <0 100 0x4>,
+				     <0 101 0x4>;
 			record;
 			channel = <8>;
 			status = "disabled";
@@ -90,7 +88,7 @@
 		};
 
 		pwm: pwm@e0180000 {
-			compatible ="st,spear13xx-pwm";
+			compatible = "st,spear13xx-pwm";
 			reg = <0xe0180000 0x1000>;
 			#pwm-cells = <2>;
 			status = "disabled";
@@ -136,9 +134,9 @@
 				reg = <0xb4100000 0x1000>;
 				interrupts = <0 105 0x4>;
 				status = "disabled";
-				dmas = <&dwdma0 12 0 1>,
-					<&dwdma0 13 1 0>;
-				dma-names = "tx", "rx";
+				dmas = <&dwdma0 13 0 1>,
+					<&dwdma0 12 1 0>;
+				dma-names = "rx", "tx";
 			};
 
 			thermal@e07008c4 {
diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/st/spear13xx.dtsi
index f187da4485f4..3b6897084e26 100644
--- a/arch/arm/boot/dts/spear13xx.dtsi
+++ b/arch/arm/boot/dts/st/spear13xx.dtsi
@@ -39,11 +39,11 @@
 
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
-		interrupts = <0 6 0x04
-			      0 7 0x04>;
+		interrupts = <0 6 0x04>,
+			     <0 7 0x04>;
 	};
 
-	L2: l2-cache {
+	L2: cache-controller {
 		    compatible = "arm,pl310-cache";
 		    reg = <0xed000000 0x1000>;
 		    cache-unified;
@@ -141,10 +141,10 @@
 			       0xb0820000 0x0010	/* NAND Base ADDR */
 			       0xb0810000 0x0010>;	/* NAND Base CMD */
 			reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
-			interrupts = <0 20 0x4
-				      0 21 0x4
-				      0 22 0x4
-				      0 23 0x4>;
+			interrupts = <0 20 0x4>,
+				     <0 21 0x4>,
+				     <0 22 0x4>,
+				     <0 23 0x4>;
 			st,mode = <2>;
 			status = "disabled";
 		};
@@ -152,8 +152,8 @@
 		gmac0: eth@e2000000 {
 			compatible = "st,spear600-gmac";
 			reg = <0xe2000000 0x8000>;
-			interrupts = <0 33 0x4
-				      0 34 0x4>;
+			interrupts = <0 33 0x4>,
+				     <0 34 0x4>;
 			interrupt-names = "macirq", "eth_wake_irq";
 			status = "disabled";
 		};
@@ -263,8 +263,8 @@
 				compatible = "st,designware-i2s";
 				reg = <0xe0180000 0x1000>;
 				interrupt-names = "play_irq", "record_irq";
-				interrupts = <0 10 0x4
-					      0 11 0x4 >;
+				interrupts = <0 10 0x4>,
+					     <0 11 0x4>;
 				status = "disabled";
 			};
 
@@ -272,8 +272,8 @@
 				compatible = "st,designware-i2s";
 				reg = <0xe0200000 0x1000>;
 				interrupt-names = "play_irq", "record_irq";
-				interrupts = <0 26 0x4
-					      0 53 0x4>;
+				interrupts = <0 26 0x4>,
+					     <0 53 0x4>;
 				status = "disabled";
 			};
 
@@ -284,9 +284,9 @@
 				#size-cells = <0>;
 				interrupts = <0 31 0x4>;
 				status = "disabled";
-				dmas = <&dwdma0 4 0 0>,
-					<&dwdma0 5 0 0>;
-				dma-names = "tx", "rx";
+				dmas = <&dwdma0 5 0 0>,
+					<&dwdma0 4 0 0>;
+				dma-names = "rx", "tx";
 			};
 
 			rtc@e0580000 {
diff --git a/arch/arm/boot/dts/spear300-evb.dts b/arch/arm/boot/dts/st/spear300-evb.dts
index 2beb30ca2cba..303ef29fb805 100644
--- a/arch/arm/boot/dts/spear300-evb.dts
+++ b/arch/arm/boot/dts/st/spear300-evb.dts
@@ -80,7 +80,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/spear300.dtsi b/arch/arm/boot/dts/st/spear300.dtsi
index b39bd5a22627..f1135e887f7b 100644
--- a/arch/arm/boot/dts/spear300.dtsi
+++ b/arch/arm/boot/dts/st/spear300.dtsi
@@ -46,7 +46,7 @@
 			status = "disabled";
 		};
 
-		shirq: interrupt-controller@0x50000000 {
+		shirq: interrupt-controller@50000000 {
 			compatible = "st,spear300-shirq";
 			reg = <0x50000000 0x1000>;
 			interrupts = <28>;
diff --git a/arch/arm/boot/dts/spear310-evb.dts b/arch/arm/boot/dts/st/spear310-evb.dts
index 1c41e4a40334..ea0b53036f7b 100644
--- a/arch/arm/boot/dts/spear310-evb.dts
+++ b/arch/arm/boot/dts/st/spear310-evb.dts
@@ -94,7 +94,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/st/spear310.dtsi
index 8ce751a1376d..ce08d8820940 100644
--- a/arch/arm/boot/dts/spear310.dtsi
+++ b/arch/arm/boot/dts/st/spear310.dtsi
@@ -34,7 +34,7 @@
 			status = "disabled";
 		};
 
-		shirq: interrupt-controller@0xb4000000 {
+		shirq: interrupt-controller@b4000000 {
 			compatible = "st,spear310-shirq";
 			reg = <0xb4000000 0x1000>;
 			interrupts = <28 29 30 1>;
@@ -92,6 +92,7 @@
 			gpiopinctrl: gpio@b4000000 {
 				compatible = "st,spear-plgpio";
 				reg = <0xb4000000 0x1000>;
+				regmap = <&pinmux>;
 				#interrupt-cells = <1>;
 				interrupt-controller;
 				gpio-controller;
diff --git a/arch/arm/boot/dts/spear320-evb.dts b/arch/arm/boot/dts/st/spear320-evb.dts
index c322407a0ade..3c026d021c92 100644
--- a/arch/arm/boot/dts/spear320-evb.dts
+++ b/arch/arm/boot/dts/st/spear320-evb.dts
@@ -95,7 +95,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/spear320-hmi.dts b/arch/arm/boot/dts/st/spear320-hmi.dts
index 367ba48aac3e..721e5ee7b680 100644
--- a/arch/arm/boot/dts/spear320-hmi.dts
+++ b/arch/arm/boot/dts/st/spear320-hmi.dts
@@ -167,7 +167,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
@@ -235,14 +235,13 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 					reg = <0x41>;
-					irq-over-gpio;
 					irq-gpios = <&gpiopinctrl 29 0x4>;
 					id = <0>;
 					blocks = <0x5>;
 					irq-trigger = <0x1>;
 
 					stmpegpio: stmpe-gpio {
-						compatible = "stmpe,gpio";
+						compatible = "st,stmpe-gpio";
 						reg = <0>;
 						gpio-controller;
 						#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/st/spear320.dtsi
index 3bc1e93a0a55..56f141297ea3 100644
--- a/arch/arm/boot/dts/spear320.dtsi
+++ b/arch/arm/boot/dts/st/spear320.dtsi
@@ -49,7 +49,7 @@
 			status = "disabled";
 		};
 
-		shirq: interrupt-controller@0xb3000000 {
+		shirq: interrupt-controller@b3000000 {
 			compatible = "st,spear320-shirq";
 			reg = <0xb3000000 0x1000>;
 			interrupts = <30 28 29 1>;
@@ -78,7 +78,7 @@
 		};
 
 		pwm: pwm@a8000000 {
-			compatible ="st,spear-pwm";
+			compatible = "st,spear-pwm";
 			reg = <0xa8000000 0x1000>;
 			#pwm-cells = <2>;
 			status = "disabled";
@@ -120,6 +120,7 @@
 			gpiopinctrl: gpio@b3000000 {
 				compatible = "st,spear-plgpio";
 				reg = <0xb3000000 0x1000>;
+				regmap = <&pinmux>;
 				#interrupt-cells = <1>;
 				interrupt-controller;
 				gpio-controller;
diff --git a/arch/arm/boot/dts/st/spear320s.dtsi b/arch/arm/boot/dts/st/spear320s.dtsi
new file mode 100644
index 000000000000..133236dc190d
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear320s.dtsi
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr320s SoC
+ *
+ * Copyright 2021 Herve Codina <herve.codina@bootlin.com>
+ */
+
+/include/ "spear320.dtsi"
+
+/ {
+	ahb {
+		apb {
+			gpiopinctrl: gpio@b3000000 {
+				/*
+				 * The "RM0321 SPEAr320s address and map
+				 * registers" document mentions interrupt 6
+				 * (NPGIO_INTR) for the PL_GPIO interrupt.
+				 */
+				interrupts = <6>;
+				interrupt-parent = <&shirq>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/spear3xx.dtsi b/arch/arm/boot/dts/st/spear3xx.dtsi
index f266b7b03482..cc88ebe7a60c 100644
--- a/arch/arm/boot/dts/spear3xx.dtsi
+++ b/arch/arm/boot/dts/st/spear3xx.dtsi
@@ -47,7 +47,7 @@
 		};
 
 		gmac: eth@e0800000 {
-			compatible = "st,spear600-gmac";
+			compatible = "snps,dwmac-3.40a";
 			reg = <0xe0800000 0x8000>;
 			interrupts = <23 22>;
 			interrupt-names = "macirq", "eth_wake_irq";
diff --git a/arch/arm/boot/dts/spear600-evb.dts b/arch/arm/boot/dts/st/spear600-evb.dts
index a25b86d149ad..a25b86d149ad 100644
--- a/arch/arm/boot/dts/spear600-evb.dts
+++ b/arch/arm/boot/dts/st/spear600-evb.dts
diff --git a/arch/arm/boot/dts/spear600.dtsi b/arch/arm/boot/dts/st/spear600.dtsi
index fd41243a0b2c..6b67c0ceaed9 100644
--- a/arch/arm/boot/dts/spear600.dtsi
+++ b/arch/arm/boot/dts/st/spear600.dtsi
@@ -47,7 +47,7 @@
 			compatible = "arm,pl110", "arm,primecell";
 			reg = <0xfc200000 0x1000>;
 			interrupt-parent = <&vic1>;
-			interrupts = <12>;
+			interrupts = <13>;
 			status = "disabled";
 		};
 
@@ -207,6 +207,36 @@
 				interrupts = <6>;
 				status = "disabled";
 			};
+
+			ssp1: spi@d0100000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xd0100000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupt-parent = <&vic0>;
+				interrupts = <26>;
+				status = "disabled";
+			};
+
+			ssp2: spi@d0180000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xd0180000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupt-parent = <&vic0>;
+				interrupts = <27>;
+				status = "disabled";
+			};
+
+			ssp3: spi@d8180000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xd8180000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupt-parent = <&vic1>;
+				interrupts = <5>;
+				status = "disabled";
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/st-pincfg.h b/arch/arm/boot/dts/st/st-pincfg.h
index d80551202292..d80551202292 100644
--- a/arch/arm/boot/dts/st-pincfg.h
+++ b/arch/arm/boot/dts/st/st-pincfg.h
diff --git a/arch/arm/boot/dts/st/ste-ab8500.dtsi b/arch/arm/boot/dts/st/ste-ab8500.dtsi
new file mode 100644
index 000000000000..dd30d08ccb9b
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ab8500.dtsi
@@ -0,0 +1,392 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Linaro Ltd
+ */
+
+#include <dt-bindings/clock/ste-ab8500.h>
+
+/ {
+	/* Essential housekeeping hardware monitors */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&gpadc 0x02>, /* Battery temperature */
+			    <&gpadc 0x03>, /* Main charger voltage */
+			    <&gpadc 0x08>, /* Main battery voltage */
+			    <&gpadc 0x09>, /* VBUS */
+			    <&gpadc 0x0a>, /* Main charger current */
+			    <&gpadc 0x0b>, /* USB charger current */
+			    <&gpadc 0x0c>, /* Backup battery voltage */
+			    <&gpadc 0x0d>, /* Die temperature */
+			    <&gpadc 0x12>; /* Crystal temperature */
+	};
+
+	soc {
+		prcmu@80157000 {
+			ab8500 {
+				compatible = "stericsson,ab8500";
+				interrupt-parent = <&intc>;
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ab8500_clock: clock-controller {
+					compatible = "stericsson,ab8500-clk";
+					#clock-cells = <1>;
+				};
+
+				ab8500_gpio: gpio {
+					compatible = "stericsson,ab8500-gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				rtc {
+					compatible = "stericsson,ab8500-rtc";
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "60S", "ALARM";
+				};
+
+				gpadc: adc {
+					compatible = "stericsson,ab8500-gpadc";
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH>,
+						     <39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "HW_CONV_END", "SW_CONV_END";
+					vddadc-supply = <&ab8500_ldo_tvout_reg>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#io-channel-cells = <1>;
+
+					/* GPADC channels */
+					bat_ctrl: channel@1 {
+						reg = <0x01>;
+					};
+					btemp_ball: channel@2 {
+						reg = <0x02>;
+					};
+					main_charger_v: channel@3 {
+						reg = <0x03>;
+					};
+					acc_detect1: channel@4 {
+						reg = <0x04>;
+					};
+					acc_detect2: channel@5 {
+						reg = <0x05>;
+					};
+					adc_aux1: channel@6 {
+						reg = <0x06>;
+					};
+					adc_aux2: channel@7 {
+						reg = <0x07>;
+					};
+					main_batt_v: channel@8 {
+						reg = <0x08>;
+					};
+					vbus_v: channel@9 {
+						reg = <0x09>;
+					};
+					main_charger_c: channel@a {
+						reg = <0x0a>;
+					};
+					usb_charger_c: channel@b {
+						reg = <0x0b>;
+					};
+					bk_bat_v: channel@c {
+						reg = <0x0c>;
+					};
+					die_temp: channel@d {
+						reg = <0x0d>;
+					};
+					usb_id: channel@e {
+						reg = <0x0e>;
+					};
+					xtal_temp: channel@12 {
+						reg = <0x12>;
+					};
+					vbat_true_meas: channel@13 {
+						reg = <0x13>;
+					};
+					bat_ctrl_and_ibat: channel@1c {
+						reg = <0x1c>;
+					};
+					vbat_meas_and_ibat: channel@1d {
+						reg = <0x1d>;
+					};
+					vbat_true_meas_and_ibat: channel@1e {
+						reg = <0x1e>;
+					};
+					bat_temp_and_ibat: channel@1f {
+						reg = <0x1f>;
+					};
+				};
+
+				thermal {
+					compatible = "stericsson,abx500-temp";
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ABX500_TEMP_WARM";
+				};
+
+				ab8500_fg {
+					compatible = "stericsson,ab8500-fg";
+					interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+						     <8 IRQ_TYPE_LEVEL_HIGH>,
+						     <28 IRQ_TYPE_LEVEL_HIGH>,
+						     <27 IRQ_TYPE_LEVEL_HIGH>,
+						     <26 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "NCONV_ACCU",
+							  "BATT_OVV",
+							  "LOW_BAT_F",
+							  "CC_INT_CALIB",
+							  "CCEOC";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x08>;
+					io-channel-names = "main_bat_v";
+				};
+
+				ab8500_btemp {
+					compatible = "stericsson,ab8500-btemp";
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH>,
+						     <80 IRQ_TYPE_LEVEL_HIGH>,
+						     <83 IRQ_TYPE_LEVEL_HIGH>,
+						     <81 IRQ_TYPE_LEVEL_HIGH>,
+						     <82 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "BAT_CTRL_INDB",
+							  "BTEMP_LOW",
+							  "BTEMP_HIGH",
+							  "BTEMP_LOW_MEDIUM",
+							  "BTEMP_MEDIUM_HIGH";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x02>,
+						      <&gpadc 0x01>;
+					io-channel-names = "btemp_ball",
+							"bat_ctrl";
+				};
+
+				ab8500_charger {
+					compatible = "stericsson,ab8500-charger";
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
+						     <11 IRQ_TYPE_LEVEL_HIGH>,
+						     <0 IRQ_TYPE_LEVEL_HIGH>,
+						     <107 IRQ_TYPE_LEVEL_HIGH>,
+						     <106 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <105 IRQ_TYPE_LEVEL_HIGH>,
+						     <104 IRQ_TYPE_LEVEL_HIGH>,
+						     <89 IRQ_TYPE_LEVEL_HIGH>,
+						     <22 IRQ_TYPE_LEVEL_HIGH>,
+						     <21 IRQ_TYPE_LEVEL_HIGH>,
+						     <16 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "MAIN_CH_UNPLUG_DET",
+							  "MAIN_CHARGE_PLUG_DET",
+							  "MAIN_EXT_CH_NOT_OK",
+							  "MAIN_CH_TH_PROT_R",
+							  "MAIN_CH_TH_PROT_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_CH_TH_PROT_R",
+							  "USB_CH_TH_PROT_F",
+							  "USB_CHARGER_NOT_OKR",
+							  "VBUS_OVV",
+							  "CH_WD_EXP",
+							  "VBUS_CH_DROP_END";
+					monitored-battery = <&battery>;
+					vddadc-supply = <&ab8500_ldo_tvout_reg>;
+					io-channels = <&gpadc 0x03>,
+						      <&gpadc 0x0a>,
+						      <&gpadc 0x09>,
+						      <&gpadc 0x0b>;
+					io-channel-names = "main_charger_v",
+							"main_charger_c",
+							"vbus_v",
+							"usb_charger_c";
+				};
+
+				ab8500_chargalg {
+					compatible = "stericsson,ab8500-chargalg";
+					monitored-battery = <&battery>;
+				};
+
+				ab8500_usb: phy {
+					compatible = "stericsson,ab8500-usb";
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ID_WAKEUP_R",
+							  "ID_WAKEUP_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_ADP_PROBE_PLUG",
+							  "USB_ADP_PROBE_UNPLUG";
+					vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
+					v-ape-supply = <&db8500_vape_reg>;
+					musb_1v8-supply = <&db8500_vsmps2_reg>;
+					clocks = <&prcmu_clk PRCMU_SYSCLK>;
+					clock-names = "sysclk";
+					#phy-cells = <0>;
+				};
+
+				key {
+					compatible = "stericsson,ab8500-poweron-key";
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+				};
+
+				ab8500-sysctrl {
+					compatible = "stericsson,ab8500-sysctrl";
+				};
+
+				pwm@1 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <1>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				pwm@2 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <2>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				pwm@3 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <3>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				codec: codec {
+					compatible = "stericsson,ab8500-codec";
+
+					V-AUD-supply = <&ab8500_ldo_audio_reg>;
+					V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
+					V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
+					V-DMIC-supply = <&ab8500_ldo_dmic_reg>;
+
+					clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
+					clock-names = "audioclk";
+
+					stericsson,earpeice-cmv = <950>; /* Units in mV. */
+				};
+
+				ext_regulators: regulator-external {
+					compatible = "stericsson,ab8500-ext-regulator";
+
+					ab8500_ext1_reg: ab8500_ext1 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-boot-on;
+						regulator-always-on;
+					};
+
+					ab8500_ext2_reg: ab8500_ext2 {
+						regulator-min-microvolt = <1360000>;
+						regulator-max-microvolt = <1360000>;
+						regulator-boot-on;
+						regulator-always-on;
+					};
+
+					ab8500_ext3_reg: ab8500_ext3 {
+						regulator-min-microvolt = <3400000>;
+						regulator-max-microvolt = <3400000>;
+						regulator-boot-on;
+					};
+				};
+
+				regulator {
+					compatible = "stericsson,ab8500-regulator";
+					vin-supply = <&ab8500_ext3_reg>;
+
+					// supplies to the display/camera
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-boot-on;
+						/* BUG: If turned off MMC will be affected. */
+						regulator-always-on;
+					};
+
+					// supplies to the on-board eMMC
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					// supply for VAUX3; SDcard slots
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					// supply for v-intcore12; VINTCORE12 LDO
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+					};
+
+					// supply for tvout; gpadc; TVOUT LDO
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+					};
+
+					// supply for ab8500-vaudio; VAUDIO LDO
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+					};
+
+					// supply for v-anamic1 VAMIC1 LDO
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+					};
+
+					// supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+					};
+
+					// supply for v-dmic; VDMIC LDO
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+					};
+
+					// supply for U8500 CSI/DSI; VANA LDO
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+					};
+				};
+			};
+		};
+
+		sound {
+			stericsson,audio-codec = <&codec>;
+			clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
+			clock-names = "sysclk", "ulpclk", "intclk";
+		};
+
+		mcde@a0350000 {
+			vana-supply = <&ab8500_ldo_ana_reg>;
+
+			dsi@a0351000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0352000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0353000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+		};
+
+		usb_per5@a03e0000 {
+			phys = <&ab8500_usb>;
+			phy-names = "usb";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ab8505.dtsi b/arch/arm/boot/dts/st/ste-ab8505.dtsi
new file mode 100644
index 000000000000..131c82508e82
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ab8505.dtsi
@@ -0,0 +1,329 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Linaro Ltd
+ */
+
+#include <dt-bindings/clock/ste-ab8500.h>
+
+/ {
+	/* Essential housekeeping hardware monitors */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&gpadc 0x02>, /* Battery temperature */
+			      <&gpadc 0x08>, /* Main battery voltage */
+			      <&gpadc 0x09>, /* VBUS */
+			      <&gpadc 0x0b>, /* Charger current */
+			      <&gpadc 0x0c>, /* Backup battery voltage */
+			      <&gpadc 0x0d>; /* Die temperature */
+	};
+
+	soc {
+		prcmu@80157000 {
+			ab8505 {
+				compatible = "stericsson,ab8505";
+				interrupt-parent = <&intc>;
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ab8500_clock: clock-controller {
+					compatible = "stericsson,ab8500-clk";
+					#clock-cells = <1>;
+				};
+
+				ab8505_gpio: gpio {
+					compatible = "stericsson,ab8505-gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				rtc {
+					compatible = "stericsson,ab8500-rtc";
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "60S", "ALARM";
+				};
+
+				gpadc: adc {
+					compatible = "stericsson,ab8500-gpadc";
+					interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "SW_CONV_END";
+					vddadc-supply = <&ab8500_ldo_adc_reg>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#io-channel-cells = <1>;
+
+					/* GPADC channels */
+					bat_ctrl: channel@1 {
+						reg = <0x01>;
+					};
+					btemp_ball: channel@2 {
+						reg = <0x02>;
+					};
+					acc_detect1: channel@4 {
+						reg = <0x04>;
+					};
+					acc_detect2: channel@5 {
+						reg = <0x05>;
+					};
+					adc_aux1: channel@6 {
+						reg = <0x06>;
+					};
+					adc_aux2: channel@7 {
+						reg = <0x07>;
+					};
+					main_batt_v: channel@8 {
+						reg = <0x08>;
+					};
+					vbus_v: channel@9 {
+						reg = <0x09>;
+					};
+					charger_c: channel@b {
+						reg = <0x0b>;
+					};
+					bk_bat_v: channel@c {
+						reg = <0x0c>;
+					};
+					die_temp: channel@d {
+						reg = <0x0d>;
+					};
+					usb_id: channel@e {
+						reg = <0x0e>;
+					};
+				};
+
+				thermal {
+					compatible = "stericsson,abx500-temp";
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ABX500_TEMP_WARM";
+				};
+
+				ab8500_fg {
+					compatible = "stericsson,ab8500-fg";
+					interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+						     <8 IRQ_TYPE_LEVEL_HIGH>,
+						     <28 IRQ_TYPE_LEVEL_HIGH>,
+						     <27 IRQ_TYPE_LEVEL_HIGH>,
+						     <26 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "NCONV_ACCU",
+							  "BATT_OVV",
+							  "LOW_BAT_F",
+							  "CC_INT_CALIB",
+							  "CCEOC";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x08>;
+					io-channel-names = "main_bat_v";
+				};
+
+				ab8500_btemp {
+					compatible = "stericsson,ab8500-btemp";
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH>,
+						     <80 IRQ_TYPE_LEVEL_HIGH>,
+						     <83 IRQ_TYPE_LEVEL_HIGH>,
+						     <81 IRQ_TYPE_LEVEL_HIGH>,
+						     <82 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "BAT_CTRL_INDB",
+							  "BTEMP_LOW",
+							  "BTEMP_HIGH",
+							  "BTEMP_LOW_MEDIUM",
+							  "BTEMP_MEDIUM_HIGH";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x02>,
+						      <&gpadc 0x01>;
+					io-channel-names = "btemp_ball",
+							  "bat_ctrl";
+				};
+
+				ab8500_charger {
+					compatible = "stericsson,ab8500-charger";
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
+						     <11 IRQ_TYPE_LEVEL_HIGH>,
+						     <0 IRQ_TYPE_LEVEL_HIGH>,
+						     <107 IRQ_TYPE_LEVEL_HIGH>,
+						     <106 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <105 IRQ_TYPE_LEVEL_HIGH>,
+						     <104 IRQ_TYPE_LEVEL_HIGH>,
+						     <89 IRQ_TYPE_LEVEL_HIGH>,
+						     <22 IRQ_TYPE_LEVEL_HIGH>,
+						     <21 IRQ_TYPE_LEVEL_HIGH>,
+						     <16 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "MAIN_CH_UNPLUG_DET",
+							  "MAIN_CHARGE_PLUG_DET",
+							  "MAIN_EXT_CH_NOT_OK",
+							  "MAIN_CH_TH_PROT_R",
+							  "MAIN_CH_TH_PROT_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_CH_TH_PROT_R",
+							  "USB_CH_TH_PROT_F",
+							  "USB_CHARGER_NOT_OKR",
+							  "VBUS_OVV",
+							  "CH_WD_EXP",
+							  "VBUS_CH_DROP_END";
+					monitored-battery = <&battery>;
+					vddadc-supply = <&ab8500_ldo_adc_reg>;
+					io-channels = <&gpadc 0x09>,
+						      <&gpadc 0x0b>;
+					io-channel-names = "vbus_v",
+							  "usb_charger_c";
+				};
+
+				ab8500_chargalg {
+					compatible = "stericsson,ab8500-chargalg";
+					monitored-battery = <&battery>;
+				};
+
+				ab8500_usb: phy {
+					compatible = "stericsson,ab8500-usb";
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ID_WAKEUP_R",
+							  "ID_WAKEUP_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_ADP_PROBE_PLUG",
+							  "USB_ADP_PROBE_UNPLUG";
+					vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
+					v-ape-supply = <&db8500_vape_reg>;
+					musb_1v8-supply = <&db8500_vsmps2_reg>;
+					clocks = <&prcmu_clk PRCMU_SYSCLK>;
+					clock-names = "sysclk";
+					#phy-cells = <0>;
+				};
+
+				key {
+					compatible = "stericsson,ab8500-poweron-key";
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+				};
+
+				ab8500-sysctrl {
+					compatible = "stericsson,ab8500-sysctrl";
+				};
+
+				pwm@1 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <1>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				codec: codec {
+					compatible = "stericsson,ab8500-codec";
+
+					V-AUD-supply = <&ab8500_ldo_audio_reg>;
+					V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
+					V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
+
+					clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
+					clock-names = "audioclk";
+
+					stericsson,earpeice-cmv = <950>; /* Units in mV. */
+				};
+
+				regulator {
+					compatible = "stericsson,ab8505-regulator";
+
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux4_reg: ab8500_ldo_aux4 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5_reg: ab8500_ldo_aux5 {
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <2790000>;
+					};
+
+					ab8500_ldo_aux6_reg: ab8500_ldo_aux6 {
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <2790000>;
+					};
+
+					// supply for v-intcore12; VINTCORE12 LDO
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+						regulator-min-microvolt = <1250000>;
+						regulator-max-microvolt = <1350000>;
+					};
+
+					// supply for gpadc; ADC LDO
+					ab8500_ldo_adc_reg: ab8500_ldo_adc {
+					};
+
+					// supply for ab8500-vaudio; VAUDIO LDO
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+					};
+
+					// supply for v-anamic1 VAMIC1 LDO
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+					};
+
+					// supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+					};
+
+					// supply for v-aux8; VAUX8 LDO
+					ab8500_ldo_aux8_reg: ab8500_ldo_aux8 {
+					};
+
+					// supply for U8500 CSI/DSI; VANA LDO
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+					};
+				};
+			};
+		};
+
+		sound {
+			stericsson,audio-codec = <&codec>;
+			clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
+			clock-names = "sysclk", "ulpclk", "intclk";
+		};
+
+		mcde@a0350000 {
+			vana-supply = <&ab8500_ldo_ana_reg>;
+
+			dsi@a0351000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0352000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0353000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+		};
+
+		usb_per5@a03e0000 {
+			phys = <&ab8500_usb>;
+			phy-names = "usb";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-db8500.dtsi b/arch/arm/boot/dts/st/ste-db8500.dtsi
new file mode 100644
index 000000000000..f1ff3f4835d7
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-db8500.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			operating-points = <998400 0
+					    798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Modem trace memory */
+		ram@6000000 {
+			reg = <0x06000000 0x00f00000>;
+			no-map;
+		};
+
+		/* Modem shared memory */
+		ram@6f00000 {
+			reg = <0x06f00000 0x00100000>;
+			no-map;
+		};
+
+		/* Modem private memory */
+		ram@7000000 {
+			reg = <0x07000000 0x01000000>;
+			no-map;
+		};
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-db8520.dtsi b/arch/arm/boot/dts/st/ste-db8520.dtsi
new file mode 100644
index 000000000000..e4e8d5fc1f8a
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-db8520.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			operating-points = <1152000 0
+					    798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Modem trace memory */
+		ram@6000000 {
+			reg = <0x06000000 0x00f00000>;
+			no-map;
+		};
+
+		/* Modem shared memory */
+		ram@6f00000 {
+			reg = <0x06f00000 0x00100000>;
+			no-map;
+		};
+
+		/* Modem private memory */
+		ram@7000000 {
+			reg = <0x07000000 0x01000000>;
+			no-map;
+		};
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-db9500.dtsi b/arch/arm/boot/dts/st/ste-db9500.dtsi
new file mode 100644
index 000000000000..4273d36e881d
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-db9500.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			operating-points = <998400 0
+					    798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
new file mode 100644
index 000000000000..31a86606beda
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
@@ -0,0 +1,650 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Linaro Ltd.
+ */
+
+#include "ste-nomadik-pinctrl.dtsi"
+
+&pinctrl {
+	/* Settings for all UART default and sleep states */
+	uart0 {
+		u0_a_1_default: u0_a_1_default {
+			default_mux {
+				function = "u0";
+				groups = "u0_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u0_a_1_sleep: u0_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO1_AJ3"; /* RTS */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+			sleep_cfg3 {
+				pins = "GPIO3_AH3"; /* TXD */
+				ste,config = <&slpm_out_wkup_pdis>;
+			};
+		};
+	};
+
+	uart1 {
+		u1rxtx_a_1_default: u1rxtx_a_1_default {
+			default_mux {
+				function = "u1";
+				groups = "u1rxtx_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO4_AH6"; /* RXD */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO5_AG6"; /* TXD */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u1rxtx_a_1_sleep: u1rxtx_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO4_AH6"; /* RXD */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO5_AG6"; /* TXD */
+				ste,config = <&slpm_out_wkup_pdis>;
+			};
+		};
+
+		u1ctsrts_a_1_default: u1ctsrts_a_1_default {
+			default_mux {
+				function = "u1";
+				groups = "u1ctsrts_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO6_AF6"; /* CTS */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO7_AG5"; /* RTS */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u1ctsrts_a_1_sleep: u1ctsrts_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO6_AF6"; /* CTS */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO7_AG5"; /* RTS */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+		};
+	};
+
+	uart2 {
+		u2rxtx_c_1_default: u2rxtx_c_1_default {
+			default_mux {
+				function = "u2";
+				groups = "u2rxtx_c_1";
+			};
+			default_cfg1 {
+				pins = "GPIO29_W2"; /* RXD */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO30_W3"; /* TXD */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u2rxtx_c_1_sleep: u2rxtx_c_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO29_W2"; /* RXD */
+				ste,config = <&in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO30_W3"; /* TXD */
+				ste,config = <&out_wkup_pdis>;
+			};
+		};
+	};
+
+	/* Settings for all I2C default and sleep states */
+	i2c0 {
+		i2c0_a_1_default: i2c0_a_1_default {
+			default_mux {
+				function = "i2c0";
+				groups = "i2c0_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c0_a_1_sleep: i2c0_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	i2c1 {
+		i2c1_b_2_default: i2c1_b_2_default {
+			default_mux {
+				function = "i2c1";
+				groups = "i2c1_b_2";
+			};
+			default_cfg1 {
+				pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c1_b_2_sleep: i2c1_b_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	i2c2 {
+		i2c2_b_1_default: i2c2_b_1_default {
+			default_mux {
+				function = "i2c2";
+				groups = "i2c2_b_1";
+			};
+			default_cfg1 {
+				pins = "GPIO8_AD5", "GPIO9_AE4"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c2_b_1_sleep: i2c2_b_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO8_AD5", "GPIO9_AE4"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+
+		i2c2_b_2_default: i2c2_b_2_default {
+			default_mux {
+				function = "i2c2";
+				groups = "i2c2_b_2";
+			};
+			default_cfg1 {
+				pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c2_b_2_sleep: i2c2_b_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	i2c3 {
+		i2c3_c_2_default: i2c3_c_2_default {
+			default_mux {
+				function = "i2c3";
+				groups = "i2c3_c_2";
+			};
+			default_cfg1 {
+				pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c3_c_2_sleep: i2c3_c_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	/*
+	 * Activating I2C4 will conflict with UART1 about the same pins so do not
+	 * enable I2C4 and UART1 at the same time.
+	 */
+	i2c4 {
+		i2c4_b_1_default: i2c4_b_1_default {
+			default_mux {
+				function = "i2c4";
+				groups = "i2c4_b_1";
+			};
+			default_cfg1 {
+				pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c4_b_1_sleep: i2c4_b_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	/* Settings for all MMC/SD/SDIO default and sleep states */
+	sdi0 {
+		/* This is the external SD card slot, 4 bits wide */
+		mc0_a_1_default: mc0_a_1_default {
+			default_mux {
+				function = "mc0";
+				groups = "mc0_a_1";
+			};
+			default_cfg1 {
+				pins =
+				"GPIO18_AC2", /* CMDDIR */
+				"GPIO19_AC1", /* DAT0DIR */
+				"GPIO20_AB4"; /* DAT2DIR */
+				ste,config = <&out_hi>;
+			};
+			default_cfg2 {
+				pins = "GPIO22_AA3"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg4 {
+				pins =
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc0_a_1_sleep: mc0_a_1_sleep {
+			sleep_cfg1 {
+				pins =
+				"GPIO18_AC2", /* CMDDIR */
+				"GPIO19_AC1", /* DAT0DIR */
+				"GPIO20_AB4"; /* DAT2DIR */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO22_AA3", /* FBCLK */
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg3 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+		};
+
+		mc0_a_2_default: mc0_a_2_default {
+			default_mux {
+				function = "mc0";
+				groups = "mc0_a_2";
+			};
+			default_cfg1 {
+				pins = "GPIO22_AA3"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg2 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc0_a_2_sleep: mc0_a_2_sleep {
+			sleep_cfg1 {
+				pins =
+				"GPIO22_AA3", /* FBCLK */
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+		};
+	};
+
+	sdi1 {
+		/* This is the WLAN SDIO 4 bits wide */
+		mc1_a_1_default: mc1_a_1_default {
+			default_mux {
+				function = "mc1";
+				groups = "mc1_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins = "GPIO209_AG15"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc1_a_1_sleep: mc1_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO209_AG15", /* FBCLK */
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+
+		mc1_a_2_default: mc1_a_2_default {
+			default_mux {
+				function = "mc1";
+				groups = "mc1_a_2";
+			};
+			default_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins =
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc1_a_2_sleep: mc1_a_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	sdi2 {
+		/* This is the eMMC 8 bits wide, usually PoP eMMC */
+		mc2_a_1_default: mc2_a_1_default {
+			default_mux {
+				function = "mc2";
+				groups = "mc2_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO128_A5"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO129_B4", /* CMD */
+				"GPIO131_A12", /* DAT0 */
+				"GPIO132_C10", /* DAT1 */
+				"GPIO133_B10", /* DAT2 */
+				"GPIO134_B9", /* DAT3 */
+				"GPIO135_A9", /* DAT4 */
+				"GPIO136_C7", /* DAT5 */
+				"GPIO137_A7", /* DAT6 */
+				"GPIO138_C5"; /* DAT7 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc2_a_1_sleep: mc2_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO128_A5"; /* CLK */
+				ste,config = <&out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO130_C8", /* FBCLK */
+				"GPIO129_B4"; /* CMD */
+				ste,config = <&in_wkup_pdis_en>;
+			};
+			sleep_cfg3 {
+				pins =
+				"GPIO131_A12", /* DAT0 */
+				"GPIO132_C10", /* DAT1 */
+				"GPIO133_B10", /* DAT2 */
+				"GPIO134_B9", /* DAT3 */
+				"GPIO135_A9", /* DAT4 */
+				"GPIO136_C7", /* DAT5 */
+				"GPIO137_A7", /* DAT6 */
+				"GPIO138_C5"; /* DAT7 */
+				ste,config = <&in_wkup_pdis>;
+			};
+		};
+	};
+
+	sdi4 {
+		/* This is the eMMC 8 bits wide, usually PCB-mounted eMMC */
+		mc4_a_1_default: mc4_a_1_default {
+			default_mux {
+				function = "mc4";
+				groups = "mc4_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO203_AE23"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins = "GPIO202_AF25"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO201_AF24", /* CMD */
+				"GPIO200_AH26", /* DAT0 */
+				"GPIO199_AH23", /* DAT1 */
+				"GPIO198_AG25", /* DAT2 */
+				"GPIO197_AH24", /* DAT3 */
+				"GPIO207_AJ23", /* DAT4 */
+				"GPIO206_AG24", /* DAT5 */
+				"GPIO205_AG23", /* DAT6 */
+				"GPIO204_AF23"; /* DAT7 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc4_a_1_sleep: mc4_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO203_AE23"; /* CLK */
+				ste,config = <&out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO202_AF25", /* FBCLK */
+				"GPIO201_AF24", /* CMD */
+				"GPIO200_AH26", /* DAT0 */
+				"GPIO199_AH23", /* DAT1 */
+				"GPIO198_AG25", /* DAT2 */
+				"GPIO197_AH24", /* DAT3 */
+				"GPIO207_AJ23", /* DAT4 */
+				"GPIO206_AG24", /* DAT5 */
+				"GPIO205_AG23", /* DAT6 */
+				"GPIO204_AF23"; /* DAT7 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	/*
+	 * Multi-rate serial ports (MSPs) - MSP3 output is internal and
+	 * cannot be muxed onto any pins.
+	 */
+	msp0 {
+		msp0txrxtfstck_a_1_default: msp0txrxtfstck_a_1_default {
+			default_msp0_mux {
+				function = "msp0";
+				groups = "msp0txrx_a_1", "msp0tfstck_a_1";
+			};
+			default_msp0_cfg {
+				pins =
+				"GPIO12_AC4", /* TXD */
+				"GPIO15_AC3", /* RXD */
+				"GPIO13_AF3", /* TFS */
+				"GPIO14_AE3"; /* TCK */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	msp1 {
+		msp1txrx_a_1_default: msp1txrx_a_1_default {
+			default_mux {
+				function = "msp1";
+				groups = "msp1txrx_a_1", "msp1_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO33_AF2";
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins =
+				"GPIO34_AE1",
+				"GPIO35_AE2",
+				"GPIO36_AG2";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	msp2 {
+		msp2_a_1_default: msp2_a_1_default {
+			/* MSP2 usually used for HDMI audio */
+			default_mux {
+				function = "msp2";
+				groups = "msp2_a_1";
+			};
+			default_cfg1 {
+				pins =
+				"GPIO193_AH27", /* TXD */
+				"GPIO194_AF27", /* TCK */
+				"GPIO195_AG28"; /* TFS */
+				ste,config = <&in_pd>;
+			};
+			default_cfg2 {
+				pins = "GPIO196_AG26"; /* RXD */
+				ste,config = <&out_lo>;
+			};
+		};
+	};
+
+	musb {
+		usb_a_1_default: usb_a_1_default {
+			default_mux {
+				function = "usb";
+				groups = "usb_a_1";
+			};
+			default_cfg1 {
+				pins =
+				"GPIO256_AF28", /* NXT */
+				"GPIO258_AD29", /* XCLK */
+				"GPIO259_AC29", /* DIR */
+				"GPIO260_AD28", /* DAT7 */
+				"GPIO261_AD26", /* DAT6 */
+				"GPIO262_AE26", /* DAT5 */
+				"GPIO263_AG29", /* DAT4 */
+				"GPIO264_AE27", /* DAT3 */
+				"GPIO265_AD27", /* DAT2 */
+				"GPIO266_AC28", /* DAT1 */
+				"GPIO267_AC27"; /* DAT0 */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg2 {
+				pins = "GPIO257_AE29"; /* STP */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		usb_a_1_sleep: usb_a_1_sleep {
+			sleep_cfg1 {
+				pins =
+				"GPIO256_AF28", /* NXT */
+				"GPIO258_AD29", /* XCLK */
+				"GPIO259_AC29"; /* DIR */
+				ste,config = <&slpm_wkup_pdis_en>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO257_AE29"; /* STP */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+			sleep_cfg3 {
+				pins =
+				"GPIO260_AD28", /* DAT7 */
+				"GPIO261_AD26", /* DAT6 */
+				"GPIO262_AE26", /* DAT5 */
+				"GPIO263_AG29", /* DAT4 */
+				"GPIO264_AE27", /* DAT3 */
+				"GPIO265_AD27", /* DAT2 */
+				"GPIO266_AC28", /* DAT1 */
+				"GPIO267_AC27"; /* DAT0 */
+				ste,config = <&slpm_in_wkup_pdis_en>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
index bda454d12150..0f87abeddc33 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
@@ -5,6 +5,8 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/ste-db8500-clkout.h>
+#include <dt-bindings/reset/stericsson,db8500-prcc-reset.h>
 #include <dt-bindings/mfd/dbx500-prcmu.h>
 #include <dt-bindings/arm/ux500_pm_domains.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -14,6 +16,22 @@
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	/* This stablilizes the device enumeration */
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+	};
+
 	chosen {
 	};
 
@@ -36,11 +54,6 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0x300>;
-			/* cpufreq controls */
-			operating-points = <998400 0
-					    800000 0
-					    400000 0
-					    200000 0>;
 			clocks = <&prcmu_clk PRCMU_ARMSS>;
 			clock-names = "cpu";
 			clock-latency = <20000>;
@@ -93,10 +106,78 @@
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "stericsson,db8500";
+		compatible = "stericsson,db8500", "simple-bus";
 		interrupt-parent = <&intc>;
 		ranges;
 
+		/*
+		 * 640KB ESRAM (embedded static random access memory), divided
+		 * into 5 banks of 128 KB each. This is a fast memory usually
+		 * used by different accelerators. We group these according to
+		 * their power domains: ESRAM0 (always on) ESRAM 1+2 and
+		 * ESRAM 3+4.
+		 */
+		sram@40000000 {
+			/* The first (always on) ESRAM 0, 128 KB */
+			compatible = "mmio-sram";
+			reg = <0x40000000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40000000 0x20000>;
+
+			sram@0 {
+				compatible = "stericsson,u8500-esram";
+				reg = <0x0 0x10000>;
+				pool;
+			};
+			lcpa: sram@10000 {
+				/*
+				 * This eSRAM is used by the DMA40 DMA controller
+				 * for Logical Channel Paramers (LCP), the address
+				 * where these parameters are stored is called "LCPA".
+				 * This is addressed directly by the driver so no
+				 * pool is used.
+				 */
+				compatible = "stericsson,u8500-esram";
+				label = "DMA40-LCPA";
+				reg = <0x10000 0x800>;
+			};
+			sram@10800 {
+				compatible = "stericsson,u8500-esram";
+				reg = <0x10800 0xf800>;
+				pool;
+			};
+		};
+		sram@40020000 {
+			/* ESRAM 1+2, 256 KB */
+			compatible = "mmio-sram";
+			reg = <0x40020000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40020000 0x40000>;
+		};
+		sram@40060000 {
+			/* ESRAM 3+4, 256 KB */
+			compatible = "mmio-sram";
+			reg = <0x40060000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40060000 0x40000>;
+
+			lcla: sram@20000 {
+				/*
+				 * This eSRAM is used by the DMA40 DMA controller
+				 * for Logical Channel Logical Addresses (LCLA), the address
+				 * where these parameters are stored is called "LCLA".
+				 * This is addressed directly by the driver so no
+				 * pool is used.
+				 */
+				compatible = "stericsson,u8500-esram";
+				label = "DMA40-LCLA";
+				reg = <0x20000 0x2000>;
+			};
+		};
+
 		ptm@801ae000 {
 			compatible = "arm,coresight-etm3x", "arm,primecell";
 			reg = <0x801ae000 0x1000>;
@@ -249,7 +330,7 @@
 			reg = <0x80150000 0x2000>;
 		};
 
-		L2: l2-cache {
+		L2: cache-controller {
 			compatible = "arm,pl310-cache";
 			reg = <0xa0412000 0x1000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
@@ -289,6 +370,10 @@
 				#clock-cells = <2>;
 			};
 
+			prcc_reset: prcc-reset-controller {
+				#reset-cells = <2>;
+			};
+
 			rtc_clk: rtc32k-clock {
 				#clock-cells = <0>;
 			};
@@ -296,6 +381,11 @@
 			smp_twd_clk: smp-twd-clock {
 				#clock-cells = <0>;
 			};
+
+			clkout_clk: clkout-clock {
+				/* Cell 1 id, cell 2 source, cell 3 div */
+				#clock-cells = <3>;
+			};
 		};
 
 		mtu@a03c6000 {
@@ -324,7 +414,7 @@
 		};
 
 		rtc@80154000 {
-			compatible = "arm,rtc-pl031", "arm,primecell";
+			compatible = "arm,pl031", "arm,primecell";
 			reg = <0x80154000 0x1000>;
 			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -335,7 +425,7 @@
 		gpio0: gpio@8012e000 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8012e000 0x80>;
+			reg = <0x8012e000 0x80>;
 			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -350,7 +440,7 @@
 		gpio1: gpio@8012e080 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8012e080 0x80>;
+			reg = <0x8012e080 0x80>;
 			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -365,7 +455,7 @@
 		gpio2: gpio@8000e000 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8000e000 0x80>;
+			reg = <0x8000e000 0x80>;
 			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -380,7 +470,7 @@
 		gpio3: gpio@8000e080 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8000e080 0x80>;
+			reg = <0x8000e080 0x80>;
 			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -395,7 +485,7 @@
 		gpio4: gpio@8000e100 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8000e100 0x80>;
+			reg = <0x8000e100 0x80>;
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -410,7 +500,7 @@
 		gpio5: gpio@8000e180 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8000e180 0x80>;
+			reg = <0x8000e180 0x80>;
 			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -425,7 +515,7 @@
 		gpio6: gpio@8011e000 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8011e000 0x80>;
+			reg = <0x8011e000 0x80>;
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -440,7 +530,7 @@
 		gpio7: gpio@8011e080 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0x8011e080 0x80>;
+			reg = <0x8011e080 0x80>;
 			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -455,7 +545,7 @@
 		gpio8: gpio@a03fe000 {
 			compatible = "stericsson,db8500-gpio",
 				"st,nomadik-gpio";
-			reg =  <0xa03fe000 0x80>;
+			reg = <0xa03fe000 0x80>;
 			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -514,9 +604,10 @@
 
 		dma: dma-controller@801C0000 {
 			compatible = "stericsson,db8500-dma40", "stericsson,dma40";
-			reg = <0x801C0000 0x1000 0x40010000 0x800>;
-			reg-names = "base", "lcpa";
+			reg = <0x801C0000 0x1000>;
+			reg-names = "base";
 			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			sram = <&lcpa>, <&lcla>;
 
 			#dma-cells = <3>;
 			memcpy-channels = <56 57 58 59 60>;
@@ -638,114 +729,130 @@
 			};
 		};
 
-		i2c@80004000 {
+		i2c0: i2c@80004000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80004000 0x1000>;
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 			clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_I2C0>;
+
+			status = "disabled";
 		};
 
-		i2c@80122000 {
+		i2c1: i2c@80122000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80122000 0x1000>;
 			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C1>;
+
+			status = "disabled";
 		};
 
-		i2c@80128000 {
+		i2c2: i2c@80128000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80128000 0x1000>;
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C2>;
+
+			status = "disabled";
 		};
 
-		i2c@80110000 {
+		i2c3: i2c@80110000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80110000 0x1000>;
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_I2C3>;
+
+			status = "disabled";
 		};
 
-		i2c@8012a000 {
+		i2c4: i2c@8012a000 {
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x8012a000 0x1000>;
 			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C4>;
+
+			status = "disabled";
 		};
 
-		spi@80002000 {
+		ssp0: spi@80002000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80002000 0x1000>;
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */
 			       <&dma 8 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SSP0>;
+
+			status = "disabled";
 		};
 
-		spi@80003000 {
+		ssp1: spi@80003000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80003000 0x1000>;
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */
 			       <&dma 9 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SSP1>;
+
+			status = "disabled";
 		};
 
-		spi@8011a000 {
+		spi0: spi@8011a000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x8011a000 0x1000>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
@@ -753,14 +860,16 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */
 			       <&dma 0 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+
+			status = "disabled";
 		};
 
-		spi@80112000 {
+		spi1: spi@80112000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80112000 0x1000>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
@@ -768,14 +877,16 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */
 			       <&dma 35 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+
+			status = "disabled";
 		};
 
-		spi@80111000 {
+		spi2: spi@80111000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80111000 0x1000>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
@@ -783,14 +894,16 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */
 			       <&dma 33 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+
+			status = "disabled";
 		};
 
-		spi@80129000 {
+		spi3: spi@80129000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80129000 0x1000>;
 			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
@@ -798,14 +911,17 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */
 			       <&dma 40 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_SPI3>;
+
+			status = "disabled";
 		};
 
-		ux500_serial0: uart@80120000 {
+		serial0: serial@80120000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80120000 0x1000>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
@@ -816,11 +932,12 @@
 
 			clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>;
 			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART0>;
 
 			status = "disabled";
 		};
 
-		ux500_serial1: uart@80121000 {
+		serial1: serial@80121000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80121000 0x1000>;
 			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
@@ -831,11 +948,12 @@
 
 			clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>;
 			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART1>;
 
 			status = "disabled";
 		};
 
-		ux500_serial2: uart@80007000 {
+		serial2: serial@80007000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x80007000 0x1000>;
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
@@ -846,11 +964,12 @@
 
 			clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>;
 			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_UART2>;
 
 			status = "disabled";
 		};
 
-		sdi0_per1@80126000 {
+		mmc@80126000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80126000 0x1000>;
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -862,11 +981,12 @@
 			clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_SDI0>;
 
 			status = "disabled";
 		};
 
-		sdi1_per2@80118000 {
+		mmc@80118000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80118000 0x1000>;
 			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
@@ -878,11 +998,12 @@
 			clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI1>;
 
 			status = "disabled";
 		};
 
-		sdi2_per3@80005000 {
+		mmc@80005000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80005000 0x1000>;
 			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
@@ -894,11 +1015,12 @@
 			clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SDI2>;
 
 			status = "disabled";
 		};
 
-		sdi3_per2@80119000 {
+		mmc@80119000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80119000 0x1000>;
 			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
@@ -910,11 +1032,12 @@
 			clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI3>;
 
 			status = "disabled";
 		};
 
-		sdi4_per2@80114000 {
+		mmc@80114000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80114000 0x1000>;
 			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
@@ -926,11 +1049,12 @@
 			clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI4>;
 
 			status = "disabled";
 		};
 
-		sdi5_per3@80008000 {
+		mmc@80008000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80008000 0x1000>;
 			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
@@ -942,6 +1066,7 @@
 			clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SDI5>;
 
 			status = "disabled";
 		};
@@ -963,6 +1088,7 @@
 
 			clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP0>;
 
 			status = "disabled";
 		};
@@ -979,6 +1105,7 @@
 
 			clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP1>;
 
 			status = "disabled";
 		};
@@ -997,6 +1124,7 @@
 
 			clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_MSP2>;
 
 			status = "disabled";
 		};
@@ -1013,6 +1141,7 @@
 
 			clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP3>;
 
 			status = "disabled";
 		};
@@ -1095,17 +1224,15 @@
 			compatible = "stericsson,ux500-cryp";
 			reg = <0xa03cb000 0x1000>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
-
-			v-ape-supply = <&db8500_vape_reg>;
 			clocks = <&prcc_pclk 6 1>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		hash@a03c2000 {
 			compatible = "stericsson,ux500-hash";
 			reg = <0xa03c2000 0x1000>;
-
-			v-ape-supply = <&db8500_vape_reg>;
 			clocks = <&prcc_pclk 6 2>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/st/ste-href-ab8500.dtsi
index 4946743de7b9..5eeb44c5e932 100644
--- a/arch/arm/boot/dts/ste-href-ab8500.dtsi
+++ b/arch/arm/boot/dts/st/ste-href-ab8500.dtsi
@@ -9,7 +9,55 @@
 	soc {
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-name = "V-DISPLAY";
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-name = "V-eMMC1";
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-name = "V-MMC-SD";
+					};
+
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+						regulator-name = "V-INTCORE";
+					};
+
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+						regulator-name = "V-TVOUT";
+					};
+
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+						regulator-name = "V-AUD";
+					};
+
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+						regulator-name = "V-AMIC1";
+					};
+
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+						regulator-name = "V-AMIC2";
+					};
+
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+						regulator-name = "V-DMIC";
+					};
+
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+						regulator-name = "V-CSI/DSI";
+					};
+				};
+
+				gpio {
 					/* Hog a few default settings */
 					pinctrl-names = "default";
 					pinctrl-0 = <&gpio2_default_mode>,
@@ -418,6 +466,24 @@
 						};
 					};
 				};
+				/*
+				 * Charging is not working on the HREF unless an actual battery is
+				 * mounted, most HREFs have a DC cable in to the "battery power"
+				 * which means this will only be cofusing. So do not enable charging
+				 * of the HREFs.
+				 */
+				ab8500_fg {
+					status = "disabled";
+				};
+				ab8500_btemp {
+					status = "disabled";
+				};
+				ab8500_charger {
+					status = "disabled";
+				};
+				ab8500_chargalg {
+					status = "disabled";
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/st/ste-href-ab8505.dtsi b/arch/arm/boot/dts/st/ste-href-ab8505.dtsi
new file mode 100644
index 000000000000..268db68ccf87
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-ab8505.dtsi
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2023 Linus Walleij <linus.walleij@linaro.org>
+ */
+
+#include "ste-ab8505.dtsi"
+
+/ {
+	soc {
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-name = "V-DISPLAY";
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-name = "V-eMMC1";
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-name = "V-MMC-SD";
+					};
+
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+						regulator-name = "V-INTCORE";
+					};
+
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+						regulator-name = "V-TVOUT";
+					};
+
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+						regulator-name = "V-AUD";
+					};
+
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+						regulator-name = "V-AMIC1";
+					};
+
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+						regulator-name = "V-AMIC2";
+					};
+
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+						regulator-name = "V-DMIC";
+					};
+
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+						regulator-name = "V-CSI/DSI";
+					};
+				};
+
+				gpio {
+					/* Hog a few default settings */
+					pinctrl-names = "default";
+					pinctrl-0 = <&gpio2_default_mode>,
+						    <&gpio4_default_mode>,
+						    <&gpio10_default_mode>,
+						    <&gpio11_default_mode>,
+						    <&gpio12_default_mode>,
+						    <&gpio13_default_mode>,
+						    <&gpio16_default_mode>,
+						    <&gpio24_default_mode>,
+						    <&gpio25_default_mode>,
+						    <&gpio36_default_mode>,
+						    <&gpio37_default_mode>,
+						    <&gpio38_default_mode>,
+						    <&gpio39_default_mode>,
+						    <&gpio42_default_mode>,
+						    <&gpio26_default_mode>,
+						    <&gpio35_default_mode>,
+						    <&ycbcr_default_mode>,
+						    <&pwm_default_mode>,
+						    <&adi1_default_mode>,
+						    <&usbuicc_default_mode>,
+						    <&dmic_default_mode>,
+						    <&extcpena_default_mode>,
+						    <&modsclsda_default_mode>;
+
+					/*
+					 * Pins 2, 4, 10, 11, 12, 13, 16, 24, 25, 36, 37, 38, 39 and 42
+					 * are muxed in as GPIO, and configured as INPUT PULL DOWN
+					 */
+					gpio2 {
+						gpio2_default_mode: gpio2_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio2_a_1";
+							};
+							default_cfg {
+								pins = "GPIO2_T9";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio4 {
+						gpio4_default_mode: gpio4_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio4_a_1";
+							};
+							default_cfg {
+								pins = "GPIO4_W2";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio10 {
+						gpio10_default_mode: gpio10_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio10_d_1";
+							};
+							default_cfg {
+								pins = "GPIO10_U17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio11 {
+						gpio11_default_mode: gpio11_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio11_d_1";
+							};
+							default_cfg {
+								pins = "GPIO11_AA18";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio12 {
+						gpio12_default_mode: gpio12_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio12_d_1";
+							};
+							default_cfg {
+								pins = "GPIO12_U16";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio13 {
+						gpio13_default_mode: gpio13_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio13_d_1";
+							};
+							default_cfg {
+								pins = "GPIO13_W17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio16 {
+						gpio16_default_mode: gpio16_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio16_a_1";
+							};
+							default_cfg {
+								pins = "GPIO16_F15";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio24 {
+						gpio24_default_mode: gpio24_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio24_a_1";
+							};
+							default_cfg {
+								pins = "GPIO24_T14";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio25 {
+						gpio25_default_mode: gpio25_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio25_a_1";
+							};
+							default_cfg {
+								pins = "GPIO25_R16";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio36 {
+						gpio36_default_mode: gpio36_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio36_a_1";
+							};
+							default_cfg {
+								pins = "GPIO36_A17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio37 {
+						gpio37_default_mode: gpio37_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio37_a_1";
+							};
+							default_cfg {
+								pins = "GPIO37_E15";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio38 {
+						gpio38_default_mode: gpio38_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio38_a_1";
+							};
+							default_cfg {
+								pins = "GPIO38_C17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio39 {
+						gpio39_default_mode: gpio39_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio39_a_1";
+							};
+							default_cfg {
+								pins = "GPIO39_E16";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio42 {
+						gpio42_default_mode: gpio42_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio42_a_1";
+							};
+							default_cfg {
+								pins = "GPIO42_U2";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/*
+					 * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW
+					 */
+					gpio26 {
+						gpio26_default_mode: gpio26_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio26_d_1";
+							};
+							default_cfg {
+								pins = "GPIO26_M16";
+								output-low;
+							};
+						};
+					};
+					gpio35 {
+						gpio35_default_mode: gpio35_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio35_d_1";
+							};
+							default_cfg {
+								pins = "GPIO35_W15";
+								output-low;
+							};
+						};
+					};
+					/*
+					 * This sets up the YCBCR connector pins, i.e. analog video out.
+					 * Set as input with no bias.
+					 */
+					ycbcr {
+						ycbcr_default_mode: ycbcr_default {
+							default_mux {
+								function = "ycbcr";
+								groups = "ycbcr0123_d_1";
+							};
+							default_cfg {
+								pins = "GPIO6_Y18",
+									 "GPIO7_AA20",
+									 "GPIO8_W18",
+									 "GPIO9_AA19";
+								input-enable;
+								bias-disable;
+							};
+						};
+					};
+					/* This sets up the PWM pins 14 and 15 */
+					pwm {
+						pwm_default_mode: pwm_default {
+							default_mux {
+								function = "pwmout";
+								groups = "pwmout1_d_1", "pwmout2_d_1";
+							};
+							default_cfg {
+								pins = "GPIO14_F14",
+									 "GPIO15_B17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* This sets up audio interface 1 */
+					adi1 {
+						adi1_default_mode: adi1_default {
+							default_mux {
+								function = "adi1";
+								groups = "adi1_d_1";
+							};
+							default_cfg {
+								pins = "GPIO17_P5",
+									 "GPIO18_R5",
+									 "GPIO19_U5",
+									 "GPIO20_T5";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* This sets up the USB UICC pins */
+					usbuicc {
+						usbuicc_default_mode: usbuicc_default {
+							default_mux {
+								function = "usbuicc";
+								groups = "usbuicc_d_1";
+							};
+							default_cfg {
+								pins = "GPIO21_H19",
+									 "GPIO22_G20",
+									 "GPIO23_G19";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* This sets up the microphone pins */
+					dmic {
+						dmic_default_mode: dmic_default {
+							default_mux {
+								function = "dmic";
+								groups = "dmic12_d_1",
+									 "dmic34_d_1",
+									 "dmic56_d_1";
+							};
+							default_cfg {
+								pins = "GPIO27_J6",
+									 "GPIO28_K6",
+									 "GPIO29_G6",
+									 "GPIO30_H6",
+									 "GPIO31_F5",
+									 "GPIO32_G5";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					extcpena {
+						extcpena_default_mode: extcpena_default {
+							default_mux {
+								function = "extcpena";
+								groups = "extcpena_d_1";
+							};
+							default_cfg {
+								pins = "GPIO34_R17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* Modem I2C setup (SCL and SDA pins) */
+					modsclsda {
+						modsclsda_default_mode: modsclsda_default {
+							default_mux {
+								function = "modsclsda";
+								groups = "modsclsda_d_1";
+							};
+							default_cfg {
+								pins = "GPIO40_T19",
+									"GPIO41_U19";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/*
+					 * Clock output pins associated with regulators.
+					 */
+					sysclkreq2 {
+						sysclkreq2_default_mode: sysclkreq2_default {
+							default_mux {
+								function = "sysclkreq";
+								groups = "sysclkreq2_d_1";
+							};
+							default_cfg {
+								pins = "GPIO1_T10";
+								input-enable;
+								bias-disable;
+							};
+						};
+						sysclkreq2_sleep_mode: sysclkreq2_sleep {
+							default_mux {
+								function = "gpio";
+								groups = "gpio1_a_1";
+							};
+							default_cfg {
+								pins = "GPIO1_T10";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					sysclkreq4 {
+						sysclkreq4_default_mode: sysclkreq4_default {
+							default_mux {
+								function = "sysclkreq";
+								groups = "sysclkreq4_d_1";
+							};
+							default_cfg {
+								pins = "GPIO3_U9";
+								input-enable;
+								bias-disable;
+							};
+						};
+						sysclkreq4_sleep_mode: sysclkreq4_sleep {
+							default_mux {
+								function = "gpio";
+								groups = "gpio3_a_1";
+							};
+							default_cfg {
+								pins = "GPIO3_U9";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+				};
+				/*
+				 * Charging is not working on the HREF unless an actual battery is
+				 * mounted, most HREFs have a DC cable in to the "battery power"
+				 * which means this will only be cofusing. So do not enable charging
+				 * of the HREFs.
+				 */
+				ab8500_fg {
+					status = "disabled";
+				};
+				ab8500_btemp {
+					status = "disabled";
+				};
+				ab8500_charger {
+					status = "disabled";
+				};
+				ab8500_chargalg {
+					status = "disabled";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-href-family-pinctrl.dtsi
new file mode 100644
index 000000000000..434fa6baf71f
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-family-pinctrl.dtsi
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Linaro Ltd.
+ */
+
+#include "ste-dbx5x0-pinctrl.dtsi"
+
+/ {
+	soc {
+		pinctrl {
+			/* Settings for all SPI default and sleep states */
+			spi2 {
+				spi2_default_mode: spi_default {
+					default_mux {
+						function = "spi2";
+						groups = "spi2_oc1_2";
+					};
+					default_cfg1 {
+						pins = "GPIO216_AG12"; /* FRM */
+						ste,config = <&gpio_out_hi>;
+					};
+					default_cfg2 {
+						pins = "GPIO218_AH11"; /* RXD */
+						ste,config = <&in_pd>;
+					};
+					default_cfg3 {
+						pins =
+						"GPIO215_AH13", /* TXD */
+						"GPIO217_AH12"; /* CLK */
+						ste,config = <&out_lo>;
+					};
+				};
+
+				spi2_idle_mode: spi_idle {
+					/*
+					 * The idle mode is basically sleep mode sans wakeups. Also
+					 * note that we have muxes the pins off the function here
+					 * as we do not state any muxing.
+					 */
+					idle_cfg1 {
+						pins = "GPIO218_AH11"; /* RXD */
+						ste,config = <&slpm_in_pdis>;
+					};
+					idle_cfg2 {
+						pins = "GPIO215_AH13"; /* TXD */
+						ste,config = <&slpm_out_lo_pdis>;
+					};
+					idle_cfg3 {
+						pins = "GPIO217_AH12"; /* CLK */
+						ste,config = <&slpm_pdis>;
+					};
+				};
+
+				spi2_sleep_mode: spi_sleep {
+					sleep_cfg1 {
+						pins =
+						"GPIO216_AG12", /* FRM */
+						"GPIO218_AH11"; /* RXD */
+						ste,config = <&slpm_in_wkup_pdis>;
+					};
+					sleep_cfg2 {
+						pins = "GPIO215_AH13"; /* TXD */
+						ste,config = <&slpm_out_lo_wkup_pdis>;
+					};
+					sleep_cfg3 {
+						pins = "GPIO217_AH12"; /* CLK */
+						ste,config = <&slpm_wkup_pdis>;
+					};
+				};
+			};
+
+			mcde {
+				lcd_default_mode: lcd_default {
+					default_mux1 {
+						/* Mux in VSI0 and all the data lines */
+						function = "lcd";
+						groups =
+						"lcdvsi0_a_1", /* VSI0 for LCD */
+						"lcd_d0_d7_a_1", /* Data lines */
+						"lcdvsi1_a_1"; /* VSI1 for HDMI */
+					};
+					default_mux2 {
+						function = "lcda";
+						groups =
+						"lcdaclk_b_1"; /* Clock line for TV-out */
+					};
+					default_cfg1 {
+						pins =
+						"GPIO68_E1", /* VSI0 */
+						"GPIO69_E2"; /* VSI1 */
+						ste,config = <&in_pu>;
+					};
+				};
+				lcd_sleep_mode: lcd_sleep {
+					sleep_cfg1 {
+						pins = "GPIO69_E2"; /* VSI1 */
+						ste,config = <&slpm_in_wkup_pdis>;
+					};
+				};
+			};
+
+			ske {
+				/* SKE keys on position 2 in an 8x8 matrix */
+				ske_kpa2_default_mode: ske_kpa2_default {
+					default_mux {
+						function = "kp";
+						groups = "kp_a_2";
+					};
+					default_cfg1 {
+						pins =
+						"GPIO153_B17", /* I7 */
+						"GPIO154_C16", /* I6 */
+						"GPIO155_C19", /* I5 */
+						"GPIO156_C17", /* I4 */
+						"GPIO161_D21", /* I3 */
+						"GPIO162_D20", /* I2 */
+						"GPIO163_C20", /* I1 */
+						"GPIO164_B21"; /* I0 */
+						ste,config = <&in_pd>;
+					};
+					default_cfg2 {
+						pins =
+						"GPIO157_A18", /* O7 */
+						"GPIO158_C18", /* O6 */
+						"GPIO159_B19", /* O5 */
+						"GPIO160_B20", /* O4 */
+						"GPIO165_C21", /* O3 */
+						"GPIO166_A22", /* O2 */
+						"GPIO167_B24", /* O1 */
+						"GPIO168_C22"; /* O0 */
+						ste,config = <&out_lo>;
+					};
+				};
+				ske_kpa2_sleep_mode: ske_kpa2_sleep {
+					sleep_cfg1 {
+						pins =
+						"GPIO153_B17", /* I7 */
+						"GPIO154_C16", /* I6 */
+						"GPIO155_C19", /* I5 */
+						"GPIO156_C17", /* I4 */
+						"GPIO161_D21", /* I3 */
+						"GPIO162_D20", /* I2 */
+						"GPIO163_C20", /* I1 */
+						"GPIO164_B21"; /* I0 */
+						ste,config = <&slpm_in_pu_wkup_pdis_en>;
+					};
+					sleep_cfg2 {
+						pins =
+						"GPIO157_A18", /* O7 */
+						"GPIO158_C18", /* O6 */
+						"GPIO159_B19", /* O5 */
+						"GPIO160_B20", /* O4 */
+						"GPIO165_C21", /* O3 */
+						"GPIO166_A22", /* O2 */
+						"GPIO167_B24", /* O1 */
+						"GPIO168_C22"; /* O0 */
+						ste,config = <&slpm_out_lo_pdis>;
+					};
+				};
+				/*
+				 * SKE keys on position 1 and "other C1" combi giving
+				 * six rows of six keys.
+				 */
+				ske_kpaoc1_default_mode: ske_kpaoc1_default {
+					default_mux {
+						function = "kp";
+						groups = "kp_a_1", "kp_oc1_1";
+					};
+					default_cfg1 {
+						pins =
+						"GPIO91_B6", /* KP_O0 */
+						"GPIO90_A3", /* KP_O1 */
+						"GPIO87_B3", /* KP_O2 */
+						"GPIO86_C6", /* KP_O3 */
+						"GPIO96_D8", /* KP_O6 */
+						"GPIO94_D7"; /* KP_O7 */
+						ste,config = <&out_lo>;
+					};
+					default_cfg2 {
+						pins =
+						"GPIO93_B7", /* KP_I0 */
+						"GPIO92_D6", /* KP_I1 */
+						"GPIO89_E6", /* KP_I2 */
+						"GPIO88_C4", /* KP_I3 */
+						"GPIO97_D9", /* KP_I6 */
+						"GPIO95_E8"; /* KP_I7 */
+						ste,config = <&in_pu>;
+					};
+				};
+			};
+
+			wlan {
+				wlan_default_mode: wlan_default {
+					/*
+					 * Activate this mode with the WLAN chip.
+					 * These are plain GPIO pins used by WLAN
+					 */
+					default_cfg1 {
+						pins =
+						"GPIO226_AF8", /* WLAN_PMU_EN */
+						"GPIO85_D5"; /* WLAN_ENA */
+						ste,config = <&gpio_out_lo>;
+					};
+					default_cfg2 {
+						pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-href-stuib.dtsi b/arch/arm/boot/dts/st/ste-href-stuib.dtsi
index e32d0c36feb8..79c2be36acae 100644
--- a/arch/arm/boot/dts/ste-href-stuib.dtsi
+++ b/arch/arm/boot/dts/st/ste-href-stuib.dtsi
@@ -30,12 +30,11 @@
 
 	soc {
 		i2c@80004000 {
-			stmpe1601: stmpe1601@40 {
+			stmpe1601: port-expander@40 {
 				compatible = "st,stmpe1601";
 				reg = <0x40>;
 				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
 				interrupt-parent = <&gpio6>;
-				interrupt-controller;
 				vcc-supply = <&db8500_vsmps2_reg>;
 				vio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
@@ -44,7 +43,7 @@
 				wakeup-source;
 				st,autosleep-timeout = <1024>;
 
-				stmpe_keypad {
+				keyboard-controller {
 					compatible = "st,stmpe-keypad";
 
 					debounce-interval = <64>;
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi
index 3bafd26b4824..7448135e25f6 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi
@@ -1,11 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
- * Copyright 2012 ST-Ericsson AB
- *
- * Device Tree for the TVK1281618 UIB
+ * Device Tree for the TVK1281618 R2 user interface board (UIB)
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	gpio_keys {
@@ -42,6 +41,7 @@
 
 				interrupt-controller;
 				#interrupt-cells = <1>;
+				status = "disabled";
 
 				tc3589x_gpio {
 					compatible = "toshiba,tc3589x-gpio";
@@ -60,30 +60,30 @@
 					keypad,num-rows = <8>;
 					linux,no-autorepeat;
 					wakeup-source;
-					linux,keymap = <0x0301006b
-						        0x04010066
-							0x06040072
-							0x040200d7
-							0x0303006a
-							0x0205000e
-							0x0607008b
-							0x0500001c
-							0x0403000b
-							0x03040034
-							0x05020067
-							0x0305006c
-							0x040500e7
-							0x0005009e
-							0x06020073
-							0x01030039
-							0x07060069
-							0x050500d9>;
+					linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>,
+						       <MATRIX_KEY(4, 1, KEY_HOME)>,
+						       <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>,
+						       <MATRIX_KEY(4, 2, KEY_EMAIL)>,
+						       <MATRIX_KEY(3, 3, KEY_RIGHT)>,
+						       <MATRIX_KEY(2, 5, KEY_BACKSPACE)>,
+						       <MATRIX_KEY(6, 7, KEY_MENU)>,
+						       <MATRIX_KEY(5, 0, KEY_ENTER)>,
+						       <MATRIX_KEY(4, 3, KEY_0)>,
+						       <MATRIX_KEY(3, 4, KEY_DOT)>,
+						       <MATRIX_KEY(5, 2, KEY_UP)>,
+						       <MATRIX_KEY(3, 5, KEY_DOWN)>,
+						       <MATRIX_KEY(4, 5, KEY_SEND)>,
+						       <MATRIX_KEY(0, 5, KEY_BACK)>,
+						       <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>,
+						       <MATRIX_KEY(1, 3, KEY_SPACE)>,
+						       <MATRIX_KEY(7, 6, KEY_LEFT)>,
+						       <MATRIX_KEY(5, 5, KEY_SEARCH)>;
 				};
 			};
 		};
-		/* Sensors mounted on this board variant */
+
 		i2c@80128000 {
-			lsm303dlh@18 {
+			accelerometer@18 {
 				/* Accelerometer */
 				compatible = "st,lsm303dlh-accel";
 				st,drdy-int-pin = <1>;
@@ -104,8 +104,11 @@
 				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
 				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
 				 */
+				mount-matrix = "0", "1", "0",
+					       "1", "0", "0",
+					       "0", "0", "-1";
 			};
-			lsm303dlh@1e {
+			magnetometer@1e {
 				/* Magnetometer */
 				compatible = "st,lsm303dlh-magn";
 				reg = <0x1e>;
@@ -123,7 +126,7 @@
 				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
 				 */
 			};
-			lis331dl@1c {
+			accelerometer@1c {
 				/* Accelerometer */
 				compatible = "st,lis331dl-accel";
 				st,drdy-int-pin = <1>;
@@ -136,8 +139,11 @@
 				/* INT2 would need to be open drain */
 				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
 					     <19 IRQ_TYPE_EDGE_RISING>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
 			};
-			ak8974@f {
+			magnetometer@f {
 				/* Magnetometer */
 				compatible = "asahi-kasei,ak8974";
 				reg = <0x0f>;
@@ -157,7 +163,7 @@
 				 * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
 				 */
 			};
-			l3g4200d@68 {
+			gyroscope@68 {
 				/* Gyroscope */
 				compatible = "st,l3g4200d-gyro";
 				st,drdy-int-pin = <2>;
@@ -170,7 +176,7 @@
 				<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
 				<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
 			};
-			lsp001wm@5c {
+			pressure@5c {
 				/* Barometer/pressure sensor */
 				compatible = "st,lps001wp-press";
 				reg = <0x5c>;
@@ -178,7 +184,6 @@
 				vddio-supply = <&db8500_vsmps2_reg>;
 			};
 		};
-
 		i2c@80110000 {
 			synaptics@4b {
 				/* Synaptics RMI4 TM1217 touchscreen */
@@ -187,34 +192,37 @@
 				#size-cells = <0>;
 				reg = <0x4b>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
-				vddio-supply = <&db8500_vsmps2_reg>;
+				vio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&synaptics_tvk_mode>;
 				interrupt-parent = <&gpio2>;
 				interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
 
-				rmi-f01@1 {
+				rmi4-f01@1 {
 					reg = <0x1>;
-					syna,nosleep = <1>;
+					syna,nosleep-mode = <1>;
 				};
-				rmi-f11@11 {
+				rmi4-f11@11 {
 					reg = <0x11>;
-					touchscreen-inverted-x;
 					syna,sensor-type = <1>;
+					/* This is a landscape display */
+					touchscreen-swapped-x-y;
 				};
 			};
 		};
+		mcde@a0350000 {
+			status = "okay";
 
-		pinctrl {
-			/* Pull up this GPIO pin */
-			tc35893 {
-				tc35893_tvk_mode: tc35893_tvk {
-					tvk_cfg {
-						pins = "GPIO218_AH11";
-						ste,config = <&gpio_in_pu>;
-					};
+			dsi@a0351000 {
+				panel {
+					compatible = "samsung,s6d16d0";
+					reg = <0>;
+					vdd1-supply = <&ab8500_ldo_aux1_reg>;
+					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 				};
 			};
+		};
+		pinctrl {
 			prox {
 				prox_tvk_mode: prox_tvk {
 					tvk_cfg {
@@ -231,6 +239,15 @@
 					};
 				};
 			};
+			tc35893 {
+				/* IRQ from the TC35893 */
+				tc35893_tvk_mode: tc35893_tvk {
+					tvk_cfg {
+						pins = "GPIO218_AH11";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
 			accelerometer {
 				accel_tvk_mode: accel_tvk {
 					/* Accelerometer interrupt lines 1 & 2 */
@@ -268,18 +285,5 @@
 				};
 			};
 		};
-
-		mcde@a0350000 {
-			status = "okay";
-
-			dsi@a0351000 {
-				panel {
-					compatible = "samsung,s6d16d0";
-					reg = <0>;
-					vdd1-supply = <&ab8500_ldo_aux1_reg>;
-					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
-				};
-			};
-		};
 	};
 };
diff --git a/arch/arm/boot/dts/st/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/st/ste-href-tvk1281618-r3.dtsi
new file mode 100644
index 000000000000..00ce9d79f540
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-tvk1281618-r3.dtsi
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the TVK1281618 R3 user interface board (UIB)
+ * also known as the "CYTTSP board"
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vdd-supply = <&ab8500_ldo_aux1_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_tvk_mode>;
+
+		button@145 {
+			/* Hall sensor */
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			linux,code = <0>; /* SW_LID */
+			label = "HED54XXU11 Hall Effect Sensor";
+		};
+	};
+
+	soc {
+		i2c@80004000 {
+			tc35893@44 {
+				compatible = "toshiba,tc35893";
+				reg = <0x44>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tc35893_tvk_mode>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				status = "disabled";
+
+				tc3589x_gpio {
+					compatible = "toshiba,tc3589x-gpio";
+					interrupts = <0>;
+
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+				tc3589x_keypad {
+					compatible = "toshiba,tc3589x-keypad";
+					interrupts = <6>;
+					debounce-delay-ms = <4>;
+					keypad,num-columns = <8>;
+					keypad,num-rows = <8>;
+					linux,no-autorepeat;
+					wakeup-source;
+					linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>,
+						       <MATRIX_KEY(4, 1, KEY_HOME)>,
+						       <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>,
+						       <MATRIX_KEY(4, 2, KEY_EMAIL)>,
+						       <MATRIX_KEY(3, 3, KEY_RIGHT)>,
+						       <MATRIX_KEY(2, 5, KEY_BACKSPACE)>,
+						       <MATRIX_KEY(6, 7, KEY_MENU)>,
+						       <MATRIX_KEY(5, 0, KEY_ENTER)>,
+						       <MATRIX_KEY(4, 3, KEY_0)>,
+						       <MATRIX_KEY(3, 4, KEY_DOT)>,
+						       <MATRIX_KEY(5, 2, KEY_UP)>,
+						       <MATRIX_KEY(3, 5, KEY_DOWN)>,
+						       <MATRIX_KEY(4, 5, KEY_SEND)>,
+						       <MATRIX_KEY(0, 5, KEY_BACK)>,
+						       <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>,
+						       <MATRIX_KEY(1, 3, KEY_SPACE)>,
+						       <MATRIX_KEY(7, 6, KEY_LEFT)>,
+						       <MATRIX_KEY(5, 5, KEY_SEARCH)>;
+				};
+			};
+		};
+
+		i2c@80128000 {
+			accelerometer@19 {
+				compatible = "st,lsm303dlhc-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x19>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+					     <19 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&accel_tvk_mode>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
+			};
+			magnetometer@1e {
+				compatible = "st,lsm303dlm-magn";
+				reg = <0x1e>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				// This interrupt is not properly working with the driver
+				// interrupt-parent = <&gpio1>;
+				// interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&magn_tvk_mode>;
+			};
+			gyroscope@68 {
+				/* Gyroscope */
+				compatible = "st,l3g4200d-gyro";
+				reg = <0x68>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+			};
+			pressure@5c {
+				/* Barometer/pressure sensor */
+				compatible = "st,lps001wp-press";
+				reg = <0x5c>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+			};
+		};
+
+		spi@80111000 {
+			num-cs = <1>;
+			cs-gpios = <&gpio6 24 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi2_default_mode>;
+			status = "okay";
+
+			touchscreen@0 {
+				compatible = "cypress,cy8ctma340";
+				/*
+				 * Actually the max frequency is 6 MHz, but over 2 MHz the
+				 * data rate needs to be restricted to max 2Mbps which the
+				 * SPI framework cannot handle.
+				 */
+				spi-max-frequency = <2000000>;
+				reg = <0>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+				vcpin-supply = <&ab8500_ldo_aux1_reg>;
+				vdd-supply = <&db8500_vsmps2_reg>;
+				reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <854>;
+				active-interval-ms = <0>;
+				touch-timeout-ms = <255>;
+				lowpower-interval-ms = <10>;
+				bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&cyttsp_tvk_mode>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+
+			dsi@a0351000 {
+				panel {
+					compatible = "sony,acx424akp";
+					reg = <0>;
+					vddi-supply = <&ab8500_ldo_aux1_reg>;
+					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+				};
+			};
+		};
+
+		pinctrl {
+			hall {
+				hall_tvk_mode: hall_tvk {
+					tvk_cfg {
+						pins = "GPIO145_C13";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			tc35893 {
+				/* IRQ from the TC35893 */
+				tc35893_tvk_mode: tc35893_tvk {
+					tvk_cfg {
+						pins = "GPIO64_F3";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			accelerometer {
+				accel_tvk_mode: accel_tvk {
+					/* Accelerometer interrupt lines 1 & 2 */
+					tvk_cfg {
+						pins = "GPIO82_C1", "GPIO83_D3";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			magnetometer {
+				magn_tvk_mode: magn_tvk {
+					/* GPIO 32 used for DRDY, pull this down */
+					tvk_cfg {
+						pins = "GPIO32_V2";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			cyttsp {
+				cyttsp_tvk_mode: cyttsp_tvk {
+					/* Touchscreen uses GPIO84 for IRQ */
+					tvk_cfg1 {
+						pins = "GPIO84_C2";
+						ste,config = <&gpio_in_pu>;
+					};
+					/* GPIO143 is reset */
+					tvk_cfg2 {
+						pins = "GPIO143_D12";
+						ste,config = <&gpio_out_hi>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/st/ste-href.dtsi
index 4f6acbd8c040..fbf0309e108f 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/st/ste-href.dtsi
@@ -4,7 +4,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
-#include "ste-dbx5x0.dtsi"
+#include <dt-bindings/leds/common.h>
 #include "ste-href-family-pinctrl.dtsi"
 
 / {
@@ -13,61 +13,103 @@
 		reg = <0x00000000 0x20000000>;
 	};
 
+	battery: battery {
+		compatible = "simple-battery";
+		battery-type = "lithium-ion-polymer";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	soc {
-		uart@80120000 {
+		serial@80120000 {
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&uart0_default_mode>;
-			pinctrl-1 = <&uart0_sleep_mode>;
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
 			status = "okay";
 		};
 
 		/* This UART is unused and thus left disabled */
-		uart@80121000 {
+		serial@80121000 {
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&uart1_default_mode>;
-			pinctrl-1 = <&uart1_sleep_mode>;
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
 		};
 
-		uart@80007000 {
+		serial@80007000 {
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&uart2_default_mode>;
-			pinctrl-1 = <&uart2_sleep_mode>;
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
 			status = "okay";
 		};
 
 		i2c@80004000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c0_default_mode>;
-			pinctrl-1 = <&i2c0_sleep_mode>;
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+			status = "okay";
 		};
 
 		i2c@80122000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c1_default_mode>;
-			pinctrl-1 = <&i2c1_sleep_mode>;
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+			status = "okay";
 		};
 
 		i2c@80128000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c2_default_mode>;
-			pinctrl-1 = <&i2c2_sleep_mode>;
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+			status = "okay";
 			lp5521@33 {
 				compatible = "national,lp5521";
 				reg = <0x33>;
 				label = "lp5521_pri";
 				clock-mode = /bits/ 8 <2>;
-				chan0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				led@0 {
+					reg = <0>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
 					linux,default-trigger = "heartbeat";
 				};
-				chan1 {
+				led@1 {
+					reg = <1>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
 				};
-				chan2 {
+				led@2 {
+					reg = <2>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
 				};
 			};
 			lp5521@34 {
@@ -75,17 +117,25 @@
 				reg = <0x34>;
 				label = "lp5521_sec";
 				clock-mode = /bits/ 8 <2>;
-				chan0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				led@0 {
+					reg = <0>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
 				};
-				chan1 {
+				led@1 {
+					reg = <1>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
 				};
-				chan2 {
+				led@2 {
+					reg = <2>;
 					led-cur = /bits/ 8 <0x2f>;
 					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
 				};
 			};
 			bh1780@29 {
@@ -96,27 +146,13 @@
 
 		i2c@80110000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c3_default_mode>;
-			pinctrl-1 = <&i2c3_sleep_mode>;
-		};
-
-		/* ST6G3244ME level translator for 1.8/2.9 V */
-		vmmci: regulator-gpio {
-			compatible = "regulator-gpio";
-
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2900000>;
-			regulator-name = "mmci-reg";
-			regulator-type = "voltage";
-
-			startup-delay-us = <100>;
-
-			states = <1800000 0x1
-				  2900000 0x0>;
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+			status = "okay";
 		};
 
 		// External Micro SD slot
-		sdi0_per1@80126000 {
+		mmc@80126000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
@@ -132,127 +168,84 @@
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
 			vqmmc-supply = <&vmmci>;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi0_default_mode>;
-			pinctrl-1 = <&sdi0_sleep_mode>;
+			pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
 
 			status = "okay";
 		};
 
 		// WLAN SDIO channel
-		sdi1_per2@80118000 {
+		mmc@80118000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
 			non-removable;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi1_default_mode>;
-			pinctrl-1 = <&sdi1_sleep_mode>;
+			pinctrl-0 = <&mc1_a_1_default>;
+			pinctrl-1 = <&mc1_a_1_sleep>;
 
 			status = "okay";
 		};
 
 		// PoP:ed eMMC
-		sdi2_per3@80005000 {
+		mmc@80005000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <8>;
 			cap-mmc-highspeed;
 			non-removable;
+			no-sdio;
+			no-sd;
 			vmmc-supply = <&db8500_vsmps2_reg>;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi2_default_mode>;
-			pinctrl-1 = <&sdi2_sleep_mode>;
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
 
 			status = "okay";
 		};
 
 		// On-board eMMC
-		sdi4_per2@80114000 {
+		mmc@80114000 {
 			arm,primecell-periphid = <0x10480180>;
 		        max-frequency = <100000000>;
 			bus-width = <8>;
 			cap-mmc-highspeed;
 			non-removable;
+			no-sdio;
+			no-sd;
 			vmmc-supply = <&ab8500_ldo_aux2_reg>;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi4_default_mode>;
-			pinctrl-1 = <&sdi4_sleep_mode>;
+			pinctrl-0 = <&mc4_a_1_default>;
+			pinctrl-1 = <&mc4_a_1_sleep>;
 
 			status = "okay";
 		};
 
 		msp0: msp@80123000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&msp0_default_mode>;
+			pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
 			status = "okay";
 		};
 
 		msp1: msp@80124000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&msp1_default_mode>;
+			pinctrl-0 = <&msp1txrx_a_1_default>;
 			status = "okay";
 		};
 
 		msp2: msp@80117000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&msp2_default_mode>;
+			pinctrl-0 = <&msp2_a_1_default>;
 		};
 
 		msp3: msp@80125000 {
 			status = "okay";
 		};
 
-		prcmu@80157000 {
-			ab8500 {
-				ab8500-gpio {
-				};
-
-				ab8500_usb {
-					pinctrl-names = "default", "sleep";
-					pinctrl-0 = <&musb_default_mode>;
-					pinctrl-1 = <&musb_sleep_mode>;
-				};
-
-				ab8500-regulators {
-					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
-						regulator-name = "V-DISPLAY";
-					};
-
-					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
-						regulator-name = "V-eMMC1";
-					};
-
-					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
-						regulator-name = "V-MMC-SD";
-					};
-
-					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
-						regulator-name = "V-INTCORE";
-					};
-
-					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
-						regulator-name = "V-TVOUT";
-					};
-
-					ab8500_ldo_audio_reg: ab8500_ldo_audio {
-						regulator-name = "V-AUD";
-					};
-
-					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
-						regulator-name = "V-AMIC1";
-					};
-
-					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
-						regulator-name = "V-AMIC2";
-					};
-
-					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
-						regulator-name = "V-DMIC";
-					};
-
-					ab8500_ldo_ana_reg: ab8500_ldo_ana {
-						regulator-name = "V-CSI/DSI";
-					};
+		pinctrl {
+			sdi0 {
+				sdi0_default_mode: sdi0_default {
+					/* Some boards set additional settings here */
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/st/ste-href520-tvk.dts b/arch/arm/boot/dts/st/ste-href520-tvk.dts
new file mode 100644
index 000000000000..5677df43c3ac
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href520-tvk.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the HREF520 version with the TVK1281618 R3 UIB
+ */
+
+/dts-v1/;
+#include "ste-db8520.dtsi"
+#include "ste-href-ab8505.dtsi"
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-tvk1281618-r3.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF520 and TVK1281618 R3 UIB";
+	compatible = "st-ericsson,href520", "st-ericsson,u8500";
+
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmci_default_mode>;
+	};
+};
+
+&pinctrl {
+	vmmci {
+		vmmci_default_mode: vmmc_default {
+			/* VMMCI level-shifter enable */
+			default_href520_cfg1 {
+				pins = "GPIO78_F4";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* VMMCI level-shifter voltage select */
+			default_href520_cfg2 {
+				pins = "GPIO5_AG6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-hrefprev60-stuib.dts b/arch/arm/boot/dts/st/ste-hrefprev60-stuib.dts
index b78be5f4c212..b142bb2d38d8 100644
--- a/arch/arm/boot/dts/ste-hrefprev60-stuib.dts
+++ b/arch/arm/boot/dts/st/ste-hrefprev60-stuib.dts
@@ -4,8 +4,8 @@
  */
 
 /dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
+#include "ste-db8500.dtsi"
+#include "ste-href-ab8500.dtsi"
 #include "ste-hrefprev60.dtsi"
 #include "ste-href-stuib.dtsi"
 
@@ -13,11 +13,23 @@
 	model = "ST-Ericsson HREF (pre-v60) and ST UIB";
 	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
 
-	/* This stablilizes the serial port enumeration */
-	aliases {
-		serial0 = &ux500_serial0;
-		serial1 = &ux500_serial1;
-		serial2 = &ux500_serial2;
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	soc {
diff --git a/arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts
new file mode 100644
index 000000000000..5da1ff41b00e
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-href-ab8500.dtsi"
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-tvk1281618-r2.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (pre-v60) and TVK1281618 R2 UIB";
+	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/st/ste-hrefprev60.dtsi
index a036defdf164..c87fd27b4434 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/st/ste-hrefprev60.dtsi
@@ -5,7 +5,6 @@
  * Device Tree for the HREF+ prior to the v60 variant.
  */
 
-#include "ste-dbx5x0.dtsi"
 #include "ste-href-ab8500.dtsi"
 #include "ste-href.dtsi"
 
@@ -18,7 +17,7 @@
 
 	soc {
 		/* Enable UART1 on this board */
-		uart@80121000 {
+		serial@80121000 {
 			status = "okay";
 		};
 
@@ -58,17 +57,12 @@
 			 */
 			pinctrl-names = "default";
 			pinctrl-0 = <&ssp0_hrefprev60_mode>;
+			status = "okay";
 		};
 
 		// External Micro SD slot
-		sdi0_per1@80126000 {
-			cd-gpios  = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>;
-		};
-
-		vmmci: regulator-gpio {
-			gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
-			enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
+		mmc@80126000 {
+			cd-gpios = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>;
 		};
 
 		pinctrl {
diff --git a/arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts b/arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts
new file mode 100644
index 000000000000..c4abe24a7cd0
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * Device Tree for the HREF version 60 or later with the ST UIB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-href-ab8500.dtsi"
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (v60+) and ST UIB";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmci_default_mode>;
+	};
+
+	soc {
+		/* Reset line for the BU21013 touchscreen */
+		i2c@80110000 {
+			/* Only one of these will be used */
+			bu21013_tp@5c {
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+				touch-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio4 17 GPIO_LINE_OPEN_DRAIN>;
+			};
+			bu21013_tp@5d {
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+				touch-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio4 17 GPIO_LINE_OPEN_DRAIN>;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	vmmci {
+		vmmci_default_mode: vmmc_default {
+			/* VMMCI level-shifter enable */
+			default_hrefv60_cfg2 {
+				pins = "GPIO169_D22";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* VMMCI level-shifter voltage select */
+			default_hrefv60_cfg3 {
+				pins = "GPIO5_AG6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts
new file mode 100644
index 000000000000..f55e8de2b516
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * Device Tree for the HREF version 60 or later with the TVK1281618 R2 UIB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-href-ab8500.dtsi"
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-tvk1281618-r2.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (v60+) and TVK1281618 R2 UIB";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmci_default_mode>;
+	};
+};
+
+&pinctrl {
+	vmmci {
+		vmmci_default_mode: vmmc_default {
+			/* VMMCI level-shifter enable */
+			default_hrefv60_cfg2 {
+				pins = "GPIO169_D22";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* VMMCI level-shifter voltage select */
+			default_hrefv60_cfg3 {
+				pins = "GPIO5_AG6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/st/ste-hrefv60plus.dtsi
index aece8eb2924f..b23966c16a32 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/st/ste-hrefv60plus.dtsi
@@ -3,14 +3,70 @@
  * Copyright 2012 ST-Ericsson AB
  */
 
-#include "ste-dbx5x0.dtsi"
-#include "ste-href-ab8500.dtsi"
 #include "ste-href.dtsi"
 
 / {
 	model = "ST-Ericsson HREF (v60+) platform with Device Tree";
 	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
 
+	thermal-zones {
+		chassis-thermal {
+			/* Poll every 20 seconds */
+			polling-delay = <20000>;
+			/* Poll every 2nd second when cooling */
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&therm1>, <&therm2>;
+
+			/* Tripping points made from rough guess about operating conditions */
+			trips {
+				chassis_alert: chassis-alert {
+					/* At 50 degrees take down the CPU frequency */
+					temperature = <50000>;
+					hysteresis = <3000>;
+					type = "active";
+				};
+				chassis_crit: chassis-crit {
+					/* Just shut down at 70 degrees */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			/* Push down the operating frequency of the SoC when it gets hot */
+			cooling-maps {
+				map0 {
+					trip = <&chassis_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					contribution = <100>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * Thermistors on the board, formally to monitor battery temperatures
+	 * but what they measure is the board temperature.
+	 */
+	therm1: thermistor@0 {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x06>; /* AUX1 */
+		pullup-uv = <1800000>;
+		pullup-ohm = <220000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	therm2: thermistor@1 {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x07>; /* AUX2 */
+		pullup-uv = <1800000>;
+		pullup-ohm = <220000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	soc {
 		/* Name the GPIO muxed rails on the HREF boards */
 		gpio@8012e000 {
@@ -133,14 +189,8 @@
 		};
 
 		// External Micro SD slot
-		sdi0_per1@80126000 {
-			cd-gpios  = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
-		};
-
-		vmmci: regulator-gpio {
-			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
-			enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
+		mmc@80126000 {
+			cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
 		};
 
 		pinctrl {
@@ -167,16 +217,6 @@
 						pins = "GPIO95_E8";
 						ste,config = <&gpio_in_pu>;
 					};
-					/* VMMCI level-shifter enable */
-					default_hrefv60_cfg2 {
-						pins = "GPIO169_D22";
-						ste,config = <&gpio_out_hi>;
-					};
-					/* VMMCI level-shifter voltage select */
-					default_hrefv60_cfg3 {
-						pins = "GPIO5_AG6";
-						ste,config = <&gpio_out_hi>;
-					};
 				};
 			};
 			ipgpio {
@@ -312,11 +352,11 @@
 					 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
 					 */
 					hrefv60_cfg1 {
-						pins ="GPIO65_F1";
+						pins = "GPIO65_F1";
 						ste,config = <&gpio_out_hi>;
 					};
 					hrefv60_cfg2 {
-						pins ="GPIO66_G3";
+						pins = "GPIO66_G3";
 						ste,config = <&gpio_out_lo>;
 					};
 				};
diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/st/ste-nomadik-nhk15.dts
index 41ed21a4fdc1..cdff33063d6f 100644
--- a/arch/arm/boot/dts/ste-nomadik-nhk15.dts
+++ b/arch/arm/boot/dts/st/ste-nomadik-nhk15.dts
@@ -99,17 +99,16 @@
 			pinctrl-names = "default";
 			reg = <0x1d>;
 		};
-		stmpe0: stmpe2401@43 {
+		stmpe0: port-expander@43 {
 			compatible = "st,stmpe2401";
 			reg = <0x43>;
 			reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; // GPIO77
 			interrupts = <12 IRQ_TYPE_EDGE_FALLING>; // GPIO76
 			interrupt-parent = <&gpio2>;
-			interrupt-controller;
 			wakeup-source;
 			pinctrl-names = "default";
 			pinctrl-0 = <&stmpe2401_1_nhk_mode>;
-			stmpe_gpio43: stmpe_gpio {
+			stmpe_gpio43: gpio {
 				compatible = "st,stmpe-gpio";
 				gpio-controller;
 				#gpio-cells = <2>;
@@ -118,7 +117,7 @@
 				/* Some pins in alternate functions */
 				st,norequest-mask = <0xf0f002>;
 			};
-			stmpe_keypad {
+			keyboard-controller {
 				compatible = "st,stmpe-keypad";
 				debounce-interval = <64>;
 				st,scan-count = <8>;
@@ -140,22 +139,21 @@
 						0x03020067 // Up
 						0x0303006c>; // Down
 			};
-			stmpe0_pwm: stmpe_pwm {
+			stmpe0_pwm: pwm {
 				compatible = "st,stmpe-pwm";
 				#pwm-cells = <2>;
 			};
 		};
-		stmpe1: stmpe2401@44 {
+		stmpe1: port-expander@44 {
 			compatible = "st,stmpe2401";
 			reg = <0x44>;
 			reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; // GPIO79
 			interrupts = <14 IRQ_TYPE_EDGE_FALLING>; // GPIO78
 			interrupt-parent = <&gpio2>;
-			interrupt-controller;
 			wakeup-source;
 			pinctrl-names = "default";
 			pinctrl-0 = <&stmpe2401_2_nhk_mode>;
-			stmpe_gpio44: stmpe_gpio {
+			stmpe_gpio44: gpio {
 				compatible = "st,stmpe-gpio";
 				gpio-controller;
 				#gpio-cells = <2>;
@@ -165,7 +163,7 @@
 				 * This will turn off SATA so that MMC/SD
 				 * can thrive
 				 */
-				mmcsd-gpio {
+				mmcsd-hog {
 					gpio-hog;
 					gpios = <2 0x0>;
 					output-low;
@@ -190,12 +188,12 @@
 		};
 
 		/* Activate RX/TX and CTS/RTS on UART 0 */
-		uart0: uart@101fd000 {
+		uart0: serial@101fd000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_nhk_mode>;
 			status = "okay";
 		};
-		mmcsd: sdi@101f6000 {
+		mmcsd: mmc@101f6000 {
 			cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
 			wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
 		};
@@ -210,8 +208,8 @@
 		 * As we're dealing with 3wire SPI, we only define SCK
 		 * and MOSI (in the spec MOSI is called "SDA").
 		 */
-		gpio-sck = <&gpio0 5 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
 		cs-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 
diff --git a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-nomadik-pinctrl.dtsi
index 5673a1113aef..bfdb5d9a014f 100644
--- a/arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/ste-nomadik-pinctrl.dtsi
@@ -25,6 +25,11 @@
 		ste,output = <OUTPUT_LOW>;
 	};
 
+	gpio_in_nopull: gpio_input_nopull {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,input = <INPUT_NOPULL>;
+	};
+
 	gpio_in_pu: gpio_input_pull_up {
 		ste,gpio = <GPIOMODE_ENABLED>;
 		ste,input = <INPUT_PULLUP>;
diff --git a/arch/arm/boot/dts/ste-nomadik-s8815.dts b/arch/arm/boot/dts/st/ste-nomadik-s8815.dts
index 4445446fa828..c905c2643a12 100644
--- a/arch/arm/boot/dts/ste-nomadik-s8815.dts
+++ b/arch/arm/boot/dts/st/ste-nomadik-s8815.dts
@@ -133,13 +133,13 @@
 
 	amba {
 		/* Activate RXTX on UART 0 */
-		uart0: uart@101fd000 {
+		uart0: serial@101fd000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_s8815_mode>;
 			status = "okay";
 		};
 		/* Configure card detect for the uSD slot */
-		mmcsd: sdi@101f6000 {
+		mmc@101f6000 {
 			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/st/ste-nomadik-stn8815.dtsi
index f78b4eabd68c..4d37c5fb553c 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/st/ste-nomadik-stn8815.dtsi
@@ -15,7 +15,7 @@
 		    <0x08000000 0x04000000>;
 	};
 
-	L2: l2-cache {
+	L2: cache-controller {
 		compatible = "arm,l210-cache";
 		reg = <0x10210000 0x1000>;
 		interrupt-parent = <&vica>;
@@ -52,7 +52,7 @@
 
 	gpio0: gpio@101e4000 {
 		compatible = "st,nomadik-gpio";
-		reg =  <0x101e4000 0x80>;
+		reg = <0x101e4000 0x80>;
 		interrupt-parent = <&vica>;
 		interrupts = <6>;
 		interrupt-controller;
@@ -66,7 +66,7 @@
 
 	gpio1: gpio@101e5000 {
 		compatible = "st,nomadik-gpio";
-		reg =  <0x101e5000 0x80>;
+		reg = <0x101e5000 0x80>;
 		interrupt-parent = <&vica>;
 		interrupts = <7>;
 		interrupt-controller;
@@ -80,7 +80,7 @@
 
 	gpio2: gpio@101e6000 {
 		compatible = "st,nomadik-gpio";
-		reg =  <0x101e6000 0x80>;
+		reg = <0x101e6000 0x80>;
 		interrupt-parent = <&vica>;
 		interrupts = <8>;
 		interrupt-controller;
@@ -94,7 +94,7 @@
 
 	gpio3: gpio@101e7000 {
 		compatible = "st,nomadik-gpio";
-		reg =  <0x101e7000 0x80>;
+		reg = <0x101e7000 0x80>;
 		ngpio = <28>;
 		interrupt-parent = <&vica>;
 		interrupts = <9>;
@@ -755,21 +755,21 @@
 			status = "disabled";
 		};
 
-		vica: intc@10140000 {
+		vica: interrupt-controller@10140000 {
 			compatible = "arm,versatile-vic";
 			interrupt-controller;
 			#interrupt-cells = <1>;
 			reg = <0x10140000 0x20>;
 		};
 
-		vicb: intc@10140020 {
+		vicb: interrupt-controller@10140020 {
 			compatible = "arm,versatile-vic";
 			interrupt-controller;
 			#interrupt-cells = <1>;
 			reg = <0x10140020 0x20>;
 		};
 
-		uart0: uart@101fd000 {
+		uart0: serial@101fd000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101fd000 0x1000>;
 			interrupt-parent = <&vica>;
@@ -782,7 +782,7 @@
 			dma-names = "rx", "tx";
 		};
 
-		uart1: uart@101fb000 {
+		uart1: serial@101fb000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101fb000 0x1000>;
 			interrupt-parent = <&vica>;
@@ -796,7 +796,7 @@
 			dma-names = "rx", "tx";
 		};
 
-		uart2: uart@101f2000 {
+		uart2: serial@101f2000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f2000 0x1000>;
 			interrupt-parent = <&vica>;
@@ -825,7 +825,7 @@
 			interrupts = <10>;
 		};
 
-		mmcsd: sdi@101f6000 {
+		mmcsd: mmc@101f6000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x101f6000 0x1000>;
 			clocks = <&sdiclk>, <&pclksdi>;
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/st/ste-snowball.dts
index efbc4467b8b7..1322abfc7acf 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/st/ste-snowball.dts
@@ -4,7 +4,7 @@
  */
 
 /dts-v1/;
-#include "ste-dbx5x0.dtsi"
+#include "ste-db9500.dtsi"
 #include "ste-href-ab8500.dtsi"
 #include "ste-href-family-pinctrl.dtsi"
 
@@ -12,18 +12,42 @@
 	model = "Calao Systems Snowball platform with device tree";
 	compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
 
-	/* This stablilizes the serial port enumeration */
-	aliases {
-		serial0 = &ux500_serial0;
-		serial1 = &ux500_serial1;
-		serial2 = &ux500_serial2;
-	};
-
 	memory {
 		device_type = "memory";
 		reg = <0x00000000 0x20000000>;
 	};
 
+	battery: battery {
+		compatible = "simple-battery";
+		battery-type = "lithium-ion-polymer";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	en_3v3_reg: en_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "en-3v3-fixed-supply";
@@ -156,19 +180,19 @@
 
 		msp0: msp@80123000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&msp0_default_mode>;
+			pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
 			status = "okay";
 		};
 
 		msp1: msp@80124000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&msp1_default_mode>;
+			pinctrl-0 = <&msp1txrx_a_1_default>;
 			status = "okay";
 		};
 
 		msp2: msp@80117000 {
 			pinctrl-names = "default";
-			pinctrl-0 = <&msp2_default_mode>;
+			pinctrl-0 = <&msp2_a_1_default>;
 		};
 
 		msp3: msp@80125000 {
@@ -205,7 +229,7 @@
 			/* GPIO228 SD_SEL */
 			gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
 			/* GPIO217 MMC_EN */
-			enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
+			enable-gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
 			enable-active-high;
 
 			regulator-min-microvolt = <1800000>;
@@ -220,7 +244,7 @@
 		};
 
 		// External Micro SD slot
-		sdi0_per1@80126000 {
+		mmc@80126000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
@@ -238,87 +262,92 @@
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
 			vqmmc-supply = <&vmmci>;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi0_default_mode>;
-			pinctrl-1 = <&sdi0_sleep_mode>;
+			pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
 
 			/* GPIO218 MMC_CD */
-			cd-gpios  = <&gpio6 26 GPIO_ACTIVE_LOW>;
+			cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
 
 			status = "okay";
 		};
 
 		// WLAN SDIO channel
-		sdi1_per2@80118000 {
+		mmc@80118000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi1_default_mode>;
-			pinctrl-1 = <&sdi1_sleep_mode>;
+			pinctrl-0 = <&mc1_a_1_default>;
+			pinctrl-1 = <&mc1_a_1_sleep>;
 
 			status = "okay";
 		};
 
 		// Unused PoP eMMC - register and put it to sleep by default */
-		sdi2_per3@80005000 {
+		mmc@80005000 {
 			arm,primecell-periphid = <0x10480180>;
 			pinctrl-names = "default";
-			pinctrl-0 = <&sdi2_sleep_mode>;
+			pinctrl-0 = <&mc2_a_1_sleep>;
 
 			status = "okay";
 		};
 
 		// On-board eMMC
-		sdi4_per2@80114000 {
+		mmc@80114000 {
 			arm,primecell-periphid = <0x10480180>;
 		        max-frequency = <100000000>;
 			bus-width = <8>;
 			cap-mmc-highspeed;
+			no-sdio;
+			no-sd;
 			vmmc-supply = <&ab8500_ldo_aux2_reg>;
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&sdi4_default_mode>;
-			pinctrl-1 = <&sdi4_sleep_mode>;
+			pinctrl-0 = <&mc4_a_1_default>;
+			pinctrl-1 = <&mc4_a_1_sleep>;
 
 			status = "okay";
 		};
 
-		uart@80120000 {
+		serial@80120000 {
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&uart0_default_mode>;
-			pinctrl-1 = <&uart0_sleep_mode>;
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
 			status = "okay";
 		};
 
 		/* This UART is unused and thus left disabled */
-		uart@80121000 {
+		serial@80121000 {
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&uart1_default_mode>;
-			pinctrl-1 = <&uart1_sleep_mode>;
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
 		};
 
-		uart@80007000 {
+		serial@80007000 {
 			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&uart2_default_mode>;
-			pinctrl-1 = <&uart2_sleep_mode>;
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
 			status = "okay";
 		};
 
 		i2c@80004000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c0_default_mode>;
-			pinctrl-1 = <&i2c0_sleep_mode>;
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+			status = "okay";
 		};
 
 		i2c@80122000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c1_default_mode>;
-			pinctrl-1 = <&i2c1_sleep_mode>;
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+			status = "okay";
 		};
 
 		i2c@80128000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c2_default_mode>;
-			pinctrl-1 = <&i2c2_sleep_mode>;
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+			status = "okay";
 			lsm303dlh@18 {
 				/* Accelerometer */
 				compatible = "st,lsm303dlh-accel";
@@ -367,22 +396,20 @@
 
 		i2c@80110000 {
 			pinctrl-names = "default","sleep";
-			pinctrl-0 = <&i2c3_default_mode>;
-			pinctrl-1 = <&i2c3_sleep_mode>;
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+			status = "okay";
 		};
 
 		spi@80002000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&ssp0_snowball_mode>;
+			status = "okay";
 		};
 
 		prcmu@80157000 {
-			cpufreq {
-				status = "okay";
-			};
-
 			ab8500 {
-				ab8500-gpio {
+				gpio {
 					/*
 					 * AB8500 GPIOs are numbered starting from 1, so the first
 					 * index 0 is what in the datasheet is called "GPIO1", and
@@ -404,13 +431,13 @@
 						     "PM_GPIO42"; /* AB8500 GPIO42 */
 				};
 
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
-					pinctrl-0 = <&musb_default_mode>;
-					pinctrl-1 = <&musb_sleep_mode>;
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ext_regulators: ab8500-ext-regulators {
+				ext_regulators: regulator-external {
 					ab8500_ext1_reg: ab8500_ext1 {
 						regulator-name = "ab8500-ext-supply1";
 					};
@@ -424,7 +451,7 @@
 					};
 				};
 
-				ab8500-regulators {
+				regulator {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
 					};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-codina-tmo.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-codina-tmo.dts
new file mode 100644
index 000000000000..c623cc35c5ea
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-codina-tmo.dts
@@ -0,0 +1,793 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Exhibit SGH-T599 also known as Codina-TMO,
+ * the "TMO" shall be read "T-Mobile" as this phone was produced exlusively
+ * for T-Mobile in the United States.
+ *
+ * This phone is closely related to the Codina, but has:
+ * - No CPU speed cap, full ~1GHz rate
+ * - Different power management IC, AB8505
+ * - As AB8505 has a micro USB phy, no TI TSU6111
+ * - Different power routing such as the removal of the external LDO for the
+ *   touchscreen in favor of using the AB8505
+ * - Using a regulator for the key backlight LED
+ * - Using the Samsung S6D27A1 panel by default
+ * - The panel is using one of the ordinary AB8505 regulators for 1.8V
+ * - WiFi/Bluetooth combi chip upgraded to BCM4334
+ * - GPIO for backlight control moved from 68 to 69
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Exhibit (SGH-T599)";
+	compatible = "samsung,codina-tmo", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both the 3.0V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3.0V";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 "MOT_EN" */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	led-touchkeys {
+		compatible = "regulator-led";
+		vled-supply = <&ab8500_ldo_aux4_reg>; // 3.3V
+		default-state = "on";
+		function = LED_FUNCTION_KBD_BACKLIGHT;
+		color = <LED_COLOR_ID_WHITE>;
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO69 is used on Codina R0.4 and Codina TMO */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd253_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* TODO: this should also be used by the SM5103 Camera power management unit */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "COMP I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			clock-frequency = <400000>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			dvdd-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO201 */
+		cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,s6d27a1";
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&ab8500_ldo_aux6_reg>;
+
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
+			interrupt-parent = <&gpio2>;
+			interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd253>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			/*
+			 * GPIO130 will be set to input no pull-up resulting in a resistor
+			 * pulling the reset high and taking the memory out of reset.
+			 */
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+			/* FIXME: add a device for the GPS here */
+		};
+
+		/* Debugging console UART connected to AB8505 */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				/* This is mostly identical to the Codina v0.4 regulators */
+				regulator {
+					ab8500_ldo_aux1 {
+						regulator-name = "v-sensors-vdd";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						regulator-name = "v-aux2";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						regulator-name = "v-mmc-sd";
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "v-aux4";
+						/*
+						 * Providing some span here makes the touchkey
+						 * LEDs actually dimmable.
+						 */
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "v-aux5";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						/* 1.8 V to the display */
+						regulator-name = "v-aux6";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						regulator-name = "v-sensors-vio";
+					};
+				};
+			};
+		};
+
+		/* I2C0 also known as "AGC I2C" */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@39 {
+				/* Codina has the Amstaos TMD2672 */
+				compatible = "amstaos,tmd2672";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+
+				/* IRQ on GPIO146 "PS_INT" */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tmd2672_codina_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			/* Bosch BMA254 accelerometer */
+			accelerometer@18 {
+				compatible = "bosch,bma254";
+				reg = <0x18>;
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "1";
+				vddio-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* TODO: write bindings and driver for this touchscreen */
+
+			/* Zinitix BT404 ISP part */
+			isp@50 {
+				compatible = "zinitix,bt404-isp";
+				reg = <0x50>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+
+			/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
+			touchscreen@20 {
+				compatible = "zinitix,bt404";
+				reg = <0x20>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				vcca-supply = <&ab8500_ldo_aux2_reg>; // 3.3V
+				vdd-supply = <&ab8500_ldo_aux5_reg>; // 1.8V
+				zinitix,mode = <2>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	sdi2 {
+		/*
+		 * GPIO130 should be set in GPIO mode and
+		 * pulled down. (Not connected.)
+		 */
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			codina_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			codina_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIOs for panel control */
+	panel {
+		panel_default_mode: panel_default {
+			codina_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+			codina_cfg2 {
+				/* ESD IRQ line "LCD detect" */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			codina_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			codina_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Backlight GPIO */
+	backlight {
+		ktd253_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			codina_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Zinitix BT404 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			codina_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor TMD2672 */
+	tmd2672 {
+		tmd2672_codina_default: tmd2672_codina {
+			codina_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for subpmu */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			codina_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			codina_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			codina_cfg2 {
+				pins = "GPIO225_AG8";
+				/* Needs pull down, no pull down resistor on board */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24",
+				       "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			codina_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			codina_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			codina_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
new file mode 100644
index 000000000000..2355ca6e9ad6
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
@@ -0,0 +1,953 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Ace 2 GT-I8160 also known as Codina.
+ *
+ * NOTE: this is the most common variant according to the vendor tree, known
+ * as "R0.0". There appears to be a "R0.4" variant with backlight on GPIO69,
+ * AB8505 and other changes. There is also talk about some variants having a
+ * Samsung S6D27A1 display, indicated by passing a different command line from
+ * the boot loader.
+ *
+ * The Samsung tree further talks about GT-I8160P and GT-I8160chn (China).
+ * The GT-I8160 plain is known as the "europe" variant.
+ * The GT-I8160P is the CDMA version and it appears to not use the ST
+ * Microelectronics accelerometer and reportedly has NFC mounted.
+ * The GT-I8160chn appears to be the same as the europe variant.
+ *
+ * There is also the Codina-TMO, Samsung SGH-T599, which has its own device
+ * tree.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Ace 2 (GT-I8160)";
+	compatible = "samsung,codina", "st-ericsson,u8500";
+
+	cpus {
+		cpu@300 {
+			/*
+			 * This has a frequency cap at ~800 MHz in the firmware.
+			 * (Changing this number here will not overclock it.)
+			 */
+			operating-points = <798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3.0V";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 "MOT_EN" */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_leds_default_mode>;
+		touchkey-led {
+			label = "touchkeys";
+			/*
+			 * GPIO194 on R0.0, R0.4 does not use this at all, it
+			 * will instead turn LDO AUX4 on/off for key led backlighy.
+			 * (Line is pulled down on R0.4)
+			 */
+			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/*
+		 * GPIO68 is for R0.0, the board file talks about a TMO variant
+		 * (R0.4) using GPIO69.
+		 */
+		enable-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd253_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			clock-frequency = <400000>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			dvdd-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+		};
+		/* TODO: this should also be used by the SM5103 Camera power management unit */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nfc@2b {
+			/* NXP NFC circuit PN544 C1 marked NXP 44501  */
+			compatible = "nxp,pn544-i2c";
+			/* IF0, IF1 high, gives I2C address 0x2B */
+			reg = <0x2b>;
+			clock-frequency = <400000>;
+			/* NFC IRQ on GPIO32 */
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			/* GPIO 31 */
+			firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+			/* GPIO88 */
+			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pn544_codina_default>;
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO201 */
+		cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/*
+		 * Some Codinas (90%) have a WideChips WS2401-based LMS380KF01
+		 * display mounted and some 10% has a Samsung S6D27A1 instead.
+		 * The boot loader needs to modify this compatible to
+		 * correspond to whatever is passed from the early Samsung boot.
+		 */
+		panel@0 {
+			compatible = "samsung,lms380kf01";
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&lcd_1v8_reg>;
+
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
+			interrupt-parent = <&gpio2>;
+			interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd253>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				/* Actually BRCM4330 */
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			/*
+			 * GPIO130 will be set to input no pull-up resulting in a resistor
+			 * pulling the reset high and taking the memory out of reset.
+			 */
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				compatible = "brcm,bcm4751";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				enable-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bcm4751_codina_default>;
+			};
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 also known as "AGC I2C" */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@39 {
+				/* Codina has the Amstaos TMD2672 */
+				compatible = "amstaos,tmd2672";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+
+				/* IRQ on GPIO146 "PS_INT" */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				/* FIXME: needs a VDDIO supply that is connected to a pull-up resistor */
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tms2672_codina_default>;
+			};
+		};
+
+		/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
+		i2c@80122000 {
+			status = "okay";
+			pinctrl-names = "default","sleep";
+			/* FIXME: If it doesn't work try what we use on Gavini */
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_codina_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			lisd3dh@19 {
+				/* ST Microelectronics Accelerometer */
+				compatible = "st,lis3dh-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x19>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "1";
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* TODO: write bindings and driver for this touchscreen */
+
+			/* Zinitix BT404 ISP part */
+			isp@50 {
+				compatible = "zinitix,bt404-isp";
+				reg = <0x50>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+
+			/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
+			touchscreen@20 {
+				compatible = "zinitix,bt404";
+				reg = <0x20>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				vcca-supply = <&ldo_tsp_3v3_reg>;
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				zinitix,mode = <2>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	sdi2 {
+		/*
+		 * This will make the resistor mounted in R0.0 pull up
+		 * the reset line and take the eMMC out of reset. On
+		 * R0.4 variants, GPIO130 should be set in GPIO mode and
+		 * pulled down. (Not connected.)
+		 */
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			codina_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			codina_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIOs for panel control */
+	panel {
+		panel_default_mode: panel_default {
+			codina_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+			codina_cfg2 {
+				/* ESD IRQ line "LCD detect" */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			gavini_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			codina_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	key-led {
+		gpio_leds_default_mode: en_led_ldo_default {
+			/* EN_LED_LDO on GPIO194 */
+			codina_cfg1 {
+				pins = "GPIO194_AF27";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			codina_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Backlight GPIO */
+	backlight {
+		ktd253_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO68_E1"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			codina_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Zinitix BT404 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			codina_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor TMS2672 */
+	tms2672 {
+		tms2672_codina_default: tms2672_codina {
+			codina_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for subpmu */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			codina_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			codina_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			codina_cfg2 {
+				pins = "GPIO225_AG8";
+				/* Needs pull down, no pull down resistor on board */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24",
+				       "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			codina_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			codina_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_codina_default: tsu6111_codina {
+			codina_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	nfc {
+		pn544_codina_default: pn544_codina {
+			/* Interrupt line */
+			codina_cfg1 {
+				pins = "GPIO32_V2";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* Enable and firmware GPIOs */
+			codina_cfg2 {
+				pins = "GPIO31_V3", "GPIO88_C4";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bcm4751 {
+		bcm4751_codina_default: bcm4751_codina {
+			/* Reset line, start out asserted */
+			codina_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			codina_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			codina_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts
new file mode 100644
index 000000000000..ad9a20ccaaeb
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts
@@ -0,0 +1,887 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Beam GT-I8530 also known as Gavini.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Beam (GT-I8530)";
+	compatible = "samsung,gavini", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb585157lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO193 EN */
+		gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>; // FIXME
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-projector {
+			linux,code = <KEY_SWITCHVIDEOMODE>;
+			label = "Projector";
+			/* GPIO32 "Projector On HotKey" */
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_leds_default_mode>;
+		used-led {
+			label = "touchkeys";
+			/* GPIO68 */
+			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	ktd259: backlight {
+		compatible = "kinetic,ktd259";
+		/* GPIO20 */
+		enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd259_backlight_default_mode>;
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
+			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&yas530_default>;
+		};
+		/* TODO: this should also be used by the NCP6914 Camera power management unit */
+	};
+
+	/*
+	 * TODO: See if we can use the PL023 for this instead.
+	 */
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO223 */
+		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,lms397kf04";
+			/* 300 ns at read cycle -> 3 MHz max speed */
+			//spi-max-frequency = <3000000>;
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&lcd_1v8_reg>;
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd259>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_2_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the Immersion ISA1200 I2C device here */
+	};
+
+	/* Bit-banged I2C on GPIO196 and GPIO197 also called "MPR_I2C" */
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_3_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the DPP2601 projector I2C device 0x1b here */
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			/* "flash detect" actually card detect */
+			cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>;
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+			/* FIXME: add a device for the GPS here */
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <43000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			/* FIXME: fix the proximity sensor bindings and driver */
+			proximity@39 {
+				/* Gavini has the GP2A030S00F proximity sensor */
+				compatible = "sharp,gp2a030s00f";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+				/* FIXME: GPIO146 provides power on, IR LED? */
+			};
+
+			gyroscope@68 {
+				compatible = "invensense,mpu3050";
+				reg = <0x68>;
+				/* GPIO226 interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+				mount-matrix = "0", "1", "0",
+					       "1", "0", "0",
+					       "0", "0", "1";
+				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				pinctrl-names = "default";
+				pinctrl-0 = <&mpu3050_default>;
+
+				/*
+				 * The MPU-3050 acts as a hub for the
+				 * accelerometer.
+				 */
+				i2c-gate {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* Bosch BMA222E accelerometer */
+					accelerometer@18 {
+						compatible = "bosch,bma222e";
+						reg = <0x18>;
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
+						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+					};
+				};
+			};
+		};
+
+		/* I2C2 "AGC I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_1_default>;
+			pinctrl-1 = <&i2c2_b_1_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_default>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Melfas MMS136 touchscreen */
+			touchscreen@48 {
+				compatible = "melfas,mms136";
+				reg = <0x48>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* AVDD is "analog supply", 2.57-3.47 V */
+				avdd-supply = <&ldo_tsp_3v3_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO for panel reset control */
+	panel {
+		panel_default_mode: panel_default {
+			gavini_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO6 */
+			gavini_cfg1 {
+				pins = "GPIO6_AF6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			gavini_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Reset line for the Yamaha YAS530 magnetometer */
+	yas530 {
+		yas530_default: yas530_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			janice_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	gpio-leds {
+		gpio_leds_default_mode: gpio_leds_default {
+			/* EN_LED_LDO on GPIO68 */
+			gavini_cfg1 {
+				pins = "GPIO68_E1";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	backlight {
+		ktd259_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO20_AB4"; /* LCD_BL_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchkeys */
+	touchkey-ldo {
+		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
+			/* TSP_LDO_ON2 on GPIO89 */
+			gavini_cfg1 {
+				pins = "GPIO89_E6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	touchkey {
+		touchkey_default_mode: touchkey_default {
+			gavini_cfg1 {
+				/* Interrupt */
+				pins = "GPIO198_AG25";
+				ste,config = <&gpio_in_nopull>;
+			};
+			gavini_cfg2 {
+				/* Reset, actually completely unused (not routed) */
+				pins = "GPIO205_AG23";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			gavini_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			gavini_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO193 */
+			skomer_cfg1 {
+				pins = "GPIO193_AH27";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO32_V2", /* Projector On HotKey */
+				       "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Atmel MXT228 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			gavini_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for Invensense MPU3050 gyroscope */
+	mpu3050 {
+		mpu3050_default: mpu3050 {
+			gavini_cfg1 {
+				/* GPIO226 used for IRQ */
+				pins = "GPIO226_AF8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for magnetometer and NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			gavini_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Immersion ISA1200 */
+	i2c-gpio-2 {
+		i2c_gpio_2_default: i2c_gpio_2 {
+			gavini_cfg1 {
+				pins = "GPIO201_AF24", "GPIO202_AF25";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the TI DPP2601 */
+	i2c-gpio-3 {
+		i2c_gpio_3_default: i2c_gpio_3 {
+			gavini_cfg1 {
+				pins = "GPIO196_AG26", "GPIO197_AH24";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			gavini_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			gavini_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			gavini_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9",
+				     "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+			gavini_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			gavini_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			gavini_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			gavini_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			gavini_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_default: tsu6111 {
+			gavini_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-golden.dts
new file mode 100644
index 000000000000..f736888474e7
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-golden.dts
@@ -0,0 +1,733 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/*
+ * Note: This device tree cannot be booted directly with the Samsung bootloader.
+ * You need an intermediate, device-tree compatible bootloader
+ * that locks the L2 cache. Otherwise the kernel will crash after decompression.
+ *
+ * There is a port of (mainline) U-Boot, see
+ * https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500#U-Boot
+ */
+/ {
+	model = "Samsung Galaxy S III mini (GT-I8190)";
+	compatible = "samsung,golden", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb-l1m7flu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio2 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio2 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "coreriver,tc360-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&ab8500_ldo_aux4_reg>;
+			vcc-supply = <&ab8500_ldo_aux6_reg>;
+
+			interrupt-parent = <&gpio2>;
+			interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_default>;
+			linux,keycodes = <KEY_MENU KEY_BACK>;
+		};
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+			dvdd-supply = <&ab8500_ldo_aux8_reg>;
+		};
+	};
+
+	soc {
+		/* External Micro SD card slot */
+		mmc@80126000 {
+			status = "okay";
+
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+
+			non-removable;
+			/*
+			 * Unfortunately, there is no way to enable the UHS
+			 * modes due to a limitation of the SD level translator:
+			 * It will either translate to 2.9V or disconnect the
+			 * DATA lines, so switching to 1.8V signal voltage fails.
+			 */
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&sd_level_translator>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+		};
+
+		/* WLAN SDIO */
+		mmc@80118000 {
+			status = "okay";
+
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+
+			non-removable;
+			cap-sd-highspeed;
+
+			vmmc-supply = <&wl_reg_on>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+
+				/* GPIO216 (WLAN_HOST_WAKE) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			status = "okay";
+
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+
+			vmmc-supply = <&vmem_3v3>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+		};
+
+		/* BT UART */
+		serial@80120000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 (BT_VREG_ON) */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* GPIO199 (BT_WAKE) */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* GPIO97 (BT_HOST_WAKE) */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default>;
+			};
+		};
+
+		/* GPF UART */
+		serial@80121000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+		};
+
+		/* Debugging console UART */
+		serial@80007000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		i2c@80004000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				compatible = "sharp,gp2ap002s00f";
+				reg = <0x44>;
+
+				/* GPIO146 (PS_INT) */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux8_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&proximity_default>;
+
+				sharp,proximity-far-hysteresis = <0x40>;
+				sharp,proximity-close-hysteresis = <0x0f>;
+			};
+		};
+
+		i2c@80128000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			imu@68 {
+				compatible = "invensense,mpu6050";
+				reg = <0x68>;
+
+				/* GPIO206 (ACC_INT) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <14 IRQ_TYPE_EDGE_RISING>;
+
+				mount-matrix = "0", "1", "0",
+					      "-1", "0", "0",
+					       "0", "0", "1";
+
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&imu_default>;
+			};
+		};
+
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			touchscreen@4a {
+				compatible = "atmel,maxtouch";
+				reg = <0x4a>;
+
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+
+				/* VDDA is "analog supply", 2.57-3.47 V */
+				vdda-supply = <&ab8500_ldo_aux2_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ab8500_ldo_aux5_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						regulator-name = "sensor_3v";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						regulator-name = "vreg_tsp_a3v3";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						regulator-name = "vdd_tf_2v91";
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "key_led_3.3v";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "vreg_tsp_1v8";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						regulator-name = "touch_key_2.2v";
+						regulator-min-microvolt = <2200000>;
+						regulator-max-microvolt = <2200000>;
+					};
+
+					ab8500_ldo_aux8 {
+						regulator-name = "sensor_1v8";
+					};
+				};
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_default_mode>;
+
+			dsi@a0351000 {
+				panel@0 {
+					compatible = "samsung,s6e63m0";
+					reg = <0>;
+					max-brightness = <15>;
+					vdd3-supply = <&panel_reg_3v0>;
+					vci-supply = <&panel_reg_1v8>;
+					reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+					/* ESD (electrostatic discharge) detection interrupt */
+					interrupt-parent = <&gpio2>;
+					interrupts = <18 IRQ_TYPE_EDGE_RISING>;
+					interrupt-names = "esd";
+					pinctrl-names = "default";
+					pinctrl-0 = <&display_default_mode>;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		label = "GPIO Buttons";
+
+		volume-up {
+			label = "Volume Up";
+			/* GPIO67 (VOL_UP) */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			/* GPIO92 (VOL_DOWN) */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		home {
+			label = "Home";
+			/* GPIO91 (HOME_KEY) */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 (MOT_EN) */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	/* External LDO for eMMC */
+	vmem_3v3: regulator-vmem {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vmem_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		startup-delay-us = <200>;
+
+		/* GPIO223 (MEM_LDO_EN) */
+		gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mem_ldo_default>;
+	};
+
+	/* TI TXS0206-29 level translator for 2.9 V */
+	sd_level_translator: regulator-sd-level-translator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+
+		startup-delay-us = <200>;
+
+		/* GPIO87 (TXS0206-29_EN) */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/*
+	 * WL_REG_ON takes WLAN out of reset and enables the internal regulators.
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the BCM chip is actually connected directly to VBAT.
+	 */
+	wl_reg_on: regulator-wl-reg-on {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg-on";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+
+		startup-delay-us = <100000>;
+
+		/* GPIO215 (WLAN_EN) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default>;
+	};
+
+	/* MIC5366 GPIO-controlled regulator */
+	panel_reg_1v8: regulator-panel-1v8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "panel-fixed-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+
+		startup-delay-us = <200>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_reg_default_mode>;
+	};
+
+	/* MIC5366 GPIO-controlled regulator */
+	panel_reg_3v0: regulator-panel-3v0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "panel-fixed-supply";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+
+		startup-delay-us = <200>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_reg_default_mode>;
+	};
+};
+
+&pinctrl {
+	gpio-keys {
+		gpio_keys_default: gpio_keys_default {
+			golden_cfg1 {
+				pins = "GPIO67",	/* VOL_UP */
+				       "GPIO91",	/* HOME_KEY */
+				       "GPIO92";	/* VOL_DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			golden_cfg1 {
+				pins = "GPIO77",	/* TOUCHKEY_SCL */
+				       "GPIO78";	/* TOUCHKEY_SDA */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	flash {
+		gpio_flash_default_mode: flash_default {
+			golden_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			golden_cfg1 {
+				pins = "GPIO151",	/* COMP_SCL */
+				       "GPIO152";	/* COMP_SDA */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	touchkey {
+		touchkey_default: touchkey_default {
+			golden_cfg1 {
+				pins = "GPIO79";	/* TOUCHKEY_INT */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	sdi0 {
+		sd_level_translator_default: sd_level_translator_default {
+			golden_cfg1 {
+				pins = "GPIO87_B3";	/* TXS0206-29_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	sdi2 {
+		mem_ldo_default: mem_ldo_default {
+			golden_cfg1 {
+				pins = "GPIO223_AH9";	/* MEM_LDO_EN */
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+
+	mcde {
+		dsi_default_mode: dsi_default {
+			default_mux1 {
+				/* Mux in VSI0 used for DSI TE */
+				function = "lcd";
+				groups =
+				"lcdvsi0_a_1"; /* VSI0 for LCD */
+			};
+			default_cfg1 {
+				pins =
+				"GPIO68_E1"; /* VSI0 */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	display {
+		display_default_mode: display_default {
+			golden_cfg1 {
+				pins = "GPIO139_C9"; /* MIPI_DSI0_RESET_N */
+				ste,config = <&gpio_out_lo>;
+			};
+			golden_cfg2 {
+				pins = "GPIO82_C1"; /* LDI_ESD_DET */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+		panel_reg_default_mode: panel_reg_default {
+			golden_cfg1 {
+				pins = "GPIO219_AG10"; /* LCD_PWR_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	proximity {
+		proximity_default: proximity_default {
+			golden_cfg1 {
+				pins = "GPIO146_D13";	/* PS_INT */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	imu {
+		imu_default: imu_default {
+			golden_cfg1 {
+				pins = "GPIO206_AG24";	/* ACC_INT */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	tsp {
+		tsp_default: tsp_default {
+			golden_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	wlan {
+		wlan_default: wlan_default {
+			golden_cfg1 {
+				pins = "GPIO216_AG12";	/* WLAN_HOST_WAKE */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+
+		wlan_en_default: wlan_en_default {
+			golden_cfg1 {
+				pins = "GPIO215_AH13";	/* WLAN_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	bluetooth {
+		bluetooth_default: bluetooth_default {
+			golden_cfg1 {
+				pins = "GPIO199_AH23",	/* BT_WAKE */
+				       "GPIO222_AJ9";	/* BT_VREG_ON */
+				ste,config = <&gpio_out_lo>;
+			};
+			golden_cfg2 {
+				pins = "GPIO97_D9";	/* BT_HOST_WAKE */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	vibrator {
+		vibrator_default: vibrator_default {
+			golden_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+};
+
+&ab8505_gpio {
+	/* Hog a few default settings */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio_default>;
+
+	gpio {
+		gpio_default: gpio_default {
+			golden_mux {
+				/* Change unused pins to GPIO mode */
+				function = "gpio";
+				groups = "gpio3_a_1",	/* default: SysClkReq4 */
+					 "gpio14_a_1";	/* default: PWMOut1 */
+			};
+			golden_cfg1 {
+				pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-janice.dts
new file mode 100644
index 000000000000..229f7c32103c
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-janice.dts
@@ -0,0 +1,998 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy S Advance (GT-I9070)";
+	compatible = "samsung,janice", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb535151vu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>; // FIXME
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchkeys.
+	 * Two GPIO lines controls two voltages of 3.3V and 1.8V
+	 * TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8
+	 * EN_LED_LDO controls VREG_KLED_3V3 (key LED)
+	 */
+	ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_KLED_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO68 controls this regulator */
+		gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_led_ldo_default_mode>;
+	};
+	ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TOUCHKEY_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO89 controls this regulator */
+		gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_on2_default_mode>;
+	};
+
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
+			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&yas529_default>;
+		};
+		/* TODO: this should also be used by the NCP6914 Camera power management unit */
+	};
+
+	/*
+	 * These pins do have an spi controller, however the controller on
+	 * these pins is not the fully featured PL022 SSP/SPI block but the
+	 * ST Micro diet "PL023" version. One of the lacking features in
+	 * this derivative is 3wire support, so it cannot be used to drive
+	 * this panel interface. We have to use GPIO bit-banging instead.
+	 */
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220 */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MISO/MOSI on GPIO224 (no separate MISO pin) */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO223 */
+		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,s6e63m0";
+			reg = <0>;
+			vdd3-supply = <&lcd_3v0_reg>;
+			vci-supply = <&lcd_1v8_reg>;
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			spi-3wire;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * Current sense amplifier on the light sensor to convert current to
+	 * voltage. We do not know if this is the actual configuration. The
+	 * sense resistor value was found by calibrating in a room ambient
+	 * light with a second mobile phone light sensor as reference. If you
+	 * pry a Janice phone apart and inspect it you may figure this out.
+	 */
+	gp2a_shunt: current-sense-shunt {
+		compatible = "current-sense-shunt";
+		io-channels = <&gpadc 0x07>;
+		shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */
+		#io-channel-cells = <0>;
+		io-channel-ranges;
+	};
+
+	/* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		clock-frequency = <400000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "coreriver,tc360-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&ldo_kled_3v3_reg>;
+			vcc-supply = <&ldo_touchkey_1v8_reg>;
+			vddio-supply = <&ldo_touchkey_1v8_reg>;
+
+			/* Interrupt on GPIO 198 */
+			interrupt-parent = <&gpio6>;
+			interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_default_mode>;
+			linux,keycodes = <KEY_MENU KEY_BACK>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_2_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the Immersion ISA1200 I2C device here */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_3_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* This is only mounted on the GT-I9070P */
+		nfc@2b { /* 0x30? */
+			/* NXP NFC circuit PN544 C1 marked NXP 44501  */
+			compatible = "nxp,pn544-i2c";
+			/* IF0, IF1 high, gives I2C address 0x2B */
+			reg = <0x2b>;
+			clock-frequency = <400000>;
+			/* NFC IRQ on GPIO32 */
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			/* GPIO 31 */
+			firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+			/* GPIO88 */
+			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pn544_janice_default>;
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-dir-cmd;
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&ab8500_ldo_aux3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4330B1 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+
+			gnss {
+				/*
+				 * The Low Noise Amplifier (LNA) power and enablement is controlled
+				 * autonomously by the GSD4t.
+				 * Janice has a SiRFstarIV-based GSD4t
+				 * Golden has a SiRFstarV 5t-based CSRG05TA03-ICJE-R.
+				 */
+				compatible = "csr,gsd4t";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO96 */
+				sirf,onoff-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsd4t_janice_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <15000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				/* Janice has the GP2AP002A00F with light sensor */
+				compatible = "sharp,gp2ap002a00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux2_reg>;
+				/* ADC channel AUX2 to read ALSOUT ambient light sensor out */
+				io-channels = <&gp2a_shunt>;
+				io-channel-names = "alsout";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_janice_default>;
+				/* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+		/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
+		i2c@80122000 {
+			status = "okay";
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_janice_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			gyroscope@68 {
+				compatible = "invensense,mpu3050";
+				reg = <0x68>;
+				/* GPIO226 interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+				/* FIXME: no idea about this */
+				mount-matrix = "1", "0", "0",
+					       "0", "1", "0",
+					       "0", "0", "1";
+				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				pinctrl-names = "default";
+				pinctrl-0 = <&mpu3050_janice_default>;
+
+				/*
+				 * The MPU-3050 acts as a hub for the
+				 * accelerometer.
+				 */
+				i2c-gate {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* Bosch BMA222 accelerometer */
+					accelerometer@8 {
+						compatible = "bosch,bma222";
+						reg = <0x08>;
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
+						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+					};
+				};
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Atmel mXT224E touchscreen */
+			touchscreen@4a {
+				compatible = "atmel,maxtouch";
+				reg = <0x4a>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* VDDA is "analog supply", 2.57-3.47 V */
+				vdda-supply = <&ldo_tsp_3v3_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO for panel reset control */
+	panel {
+		panel_default_mode: panel_default {
+			janice_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO6 */
+			janice_cfg1 {
+				pins = "GPIO6_AF6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			janice_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	key-led {
+		en_led_ldo_default_mode: en_led_ldo_default {
+			/* EN_LED_LDO on GPIO68 */
+			janice_cfg1 {
+				pins = "GPIO68_E1";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchkeys */
+	touchkey-ldo {
+		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
+			/* TSP_LDO_ON2 on GPIO89 */
+			janice_cfg1 {
+				pins = "GPIO89_E6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	touchkey {
+		touchkey_default_mode: touchkey_default {
+			janice_cfg1 {
+				/* Interrupt */
+				pins = "GPIO198_AG25";
+				ste,config = <&gpio_in_nopull>;
+			};
+			janice_cfg2 {
+				/* Reset, actually completely unused (not routed) */
+				pins = "GPIO205_AG23";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enabled the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			janice_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			janice_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			janice_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Atmel MXT228 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			janice_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Reset line for the Yamaha YAS529 magnetometer */
+	yas529 {
+		yas529_default: yas529_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_janice_default: gp2ap002_janice {
+			janice_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for Invensense MPU3050 gyroscope */
+	mpu3050 {
+		mpu3050_janice_default: mpu3050_janice {
+			janice_cfg1 {
+				/* GPIO226 used for IRQ */
+				pins = "GPIO226_AF8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for magnetometer and NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			janice_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Cypress touchkeys */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			janice_cfg1 {
+				pins = "GPIO196_AG26", "GPIO197_AH24";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Immersion ISA1200 */
+	i2c-gpio-2 {
+		i2c_gpio_2_default: i2c_gpio_2 {
+			janice_cfg1 {
+				pins = "GPIO201_AF24", "GPIO202_AF25";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-3 {
+		i2c_gpio_3_default: i2c_gpio_3 {
+			janice_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0 {
+			janice_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* This pin is unused but belongs with this SPI block */
+			janice_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&in_pd>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			janice_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			janice_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			janice_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			janice_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_janice_default: tsu6111_janice {
+			janice_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	nfc {
+		pn544_janice_default: pn544_janice {
+			/* Interrupt line */
+			janice_cfg1 {
+				pins = "GPIO32_V2";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* Enable and firmware GPIOs */
+			janice_cfg2 {
+				pins = "GPIO31_V3", "GPIO88_C4";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	gsd4t {
+		gsd4t_janice_default: gsd4t_janice {
+			/* Reset line, start out asserted */
+			janice_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			janice_cfg2 {
+				pins = "GPIO96_D8";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* Unused power enablement line, used in R0.0 and R0.1 boards */
+			janice_cfg3 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-kyle.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-kyle.dts
new file mode 100644
index 000000000000..cdb147dcc1db
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-kyle.dts
@@ -0,0 +1,727 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Amp SGH-I407 also known as Kyle.
+ *
+ * The code also refers to "Kyle AT&T" reflecting that this mobile phone
+ * was customized for the AT&T subsidiary Aio Wireless (All In One) and
+ * offered by the company in 2013.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Amp (SGH-I407)";
+	compatible = "samsung,kyle", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161la";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "en-3v3-fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	wlan_en: regulator-gpio-wlan-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wl-reg-on";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <200000>;
+		/* GPIO215 WLAN_EN */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default_mode>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO 69 */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: this should be used by the NCP6914 Camera power management unit */
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+			dvdd-supply = <&ab8500_ldo_aux6_reg>;
+		};
+	};
+
+	soc {
+		// External Micro SD slot
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_1_default>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
+			cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			vmmc-supply = <&wlan_en>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/*
+		 * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
+		 */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			/* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
+			post-power-on-delay-ms = <300>;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPF UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */
+				compatible = "csr,csrg05ta03-icje-r";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&g05ta03_kyle_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to AB8505 USB */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "AUX1";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Supplies the MMS touchscreen only with 3.3V */
+						regulator-name = "AUX2";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "AUX3";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "AUX4";
+						/* Hammer to 3.3V for the touchscreen */
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "AUX5";
+						/* 1.8V for the touchscreen */
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						regulator-name = "AUX6";
+						/* Used by sensors for 1.8 V in R0.1+ */
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						/* Unused */
+						regulator-name = "AUX8";
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				compatible = "sharp,gp2ap002s00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux6_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_kyle_default>;
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+		/* I2C2 */
+		i2c@80128000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			accel@18 {
+				compatible = "bosch,bma254";
+				clock-frequency = <400000>;
+				reg = <0x18>;
+
+				mount-matrix = "-1", "0", "0",
+					       "0", "-1", "0",
+					       "0", "0", "-1";
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux6_reg>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Melfas MMS134S touchscreen */
+			touchscreen@48 {
+				compatible = "melfas,mms134s";
+				reg = <0x48>;
+				/* GPIO218 for IRQ */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* AVDD is "analog supply", 2.57-3.47 V */
+				avdd-supply = <&ab8500_ldo_aux2_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ab8500_ldo_aux5_reg>;
+
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&mms134s_kyle_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_default_mode>;
+
+			dsi@a0351000 {
+				panel {
+					/*
+					 * NT35510-based Hydis HVA40WV1
+					 * Apparently some Kyle models can have a NT35512 fitted
+					 * here instead. In that case the boot loader needs to
+					 * modify this compatible.
+					 */
+					compatible = "hydis,hva40wv1", "novatek,nt35510";
+					reg = <0>;
+					/* v_lcd_3v0 2.3-4.8V */
+					vdd-supply = <&lcd_3v0_reg>;
+					/* v_lcd_1v8 1.65-3.3V */
+					vddi-supply = <&lcd_1v8_reg>;
+					/* GPIO 139 */
+					reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&display_default_mode>;
+					backlight = <&ktd253>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_1 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_1_default {
+			default_cfg1 {
+				/* GPIO18, 19 & 20 unused so pull down */
+				ste,config = <&gpio_in_pd>;
+			};
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	mcde {
+		dsi_default_mode: dsi_default {
+			default_mux1 {
+				/* Mux in VSI0 used for DSI TE */
+				function = "lcd";
+				groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
+			};
+			default_cfg1 {
+				pins = "GPIO68_E1"; /* VSI0 */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	/* Two GPIO lines used by the display */
+	display {
+		display_default_mode: display_default {
+			kyle_cfg1 {
+				/*
+				 * OLED DETECT or check_pba, this appears to be high
+				 * on "PBA" which I guess is "prototype board A".
+				 */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+			kyle_cfg2 {
+				pins = "GPIO139_C9";
+				/*
+				 * MIPI_DSI0_RESET_N resets the display, leave high
+				 * (de-asserted) so we only assert reset explicitly
+				 * from the display driver.
+				 */
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			kyle_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+
+	backlight {
+		gpio_backlight_default_mode: backlight_default {
+			kyle_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	flash {
+		gpio_flash_default_mode: flash_default {
+			kyle_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			kyle_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			kyle_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			kyle_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+					ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_kyle_default: gp2ap002_kyle {
+			kyle_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			kyle_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for ALPS HSCD compass */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			kyle_cfg1 {
+				pins = "GPIO151_B17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			kyle_cfg1 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		wlan_en_default_mode: wlan_en_default {
+			kyle_cfg2 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			kyle_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			kyle_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			kyle_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Interrupt line for the Melfas MMS134S touchscreen */
+	touchscreen {
+		mms134s_kyle_default: mms134s_kyle {
+			kyle_cfg1 {
+				pins = "GPIO218_AH11";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	g05ta03 {
+		g05ta03_kyle_default: g05ta03 {
+			/* Reset line, start out de-asserted */
+			kyle_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			kyle_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+};
+
+&ab8505_gpio {
+	/* Hog a few default settings */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio_default>;
+
+	gpio {
+		gpio_default: gpio_default {
+			kyle_mux {
+				/* Change unused pins to GPIO mode */
+				function = "gpio";
+				groups = "gpio3_a_1",	/* default: SysClkReq4 */
+					 "gpio14_a_1";	/* default: PWMOut1 */
+			};
+			kyle_cfg1 {
+				pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts
new file mode 100644
index 000000000000..064d6fee8821
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts
@@ -0,0 +1,714 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung XCover 2 GT-S7710 also known as Skomer.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung XCover 2 (GT-S7710)";
+	compatible = "samsung,skomer", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb485159lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "en-3v3-fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	wlan_en: regulator-gpio-wlan-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wl-reg-on";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <200000>;
+		/* GPIO215 WLAN_EN */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default_mode>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+		button-menu {
+			linux,code = <KEY_MENU>;
+			label = "MENU";
+			/* GPIO204 */
+			gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+		};
+		button-back {
+			linux,code = <KEY_BACK>;
+			label = "BACK";
+			/* GPIO205 */
+			gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO 69 */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: this should be used by the NCP6914 Camera power management unit */
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+			dvdd-supply = <&ab8500_ldo_aux8_reg>;
+		};
+	};
+
+	soc {
+		// External Micro SD slot
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			/* All direction control is used */
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_1_default>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			vmmc-supply = <&wlan_en>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/*
+		 * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
+		 */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			/* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
+			post-power-on-delay-ms = <300>;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			/* FIXME: not quite working yet, probably needs regulators */
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */
+				compatible = "csr,csrg05ta03-icje-r";
+				/* GPS_RSTN on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&g05ta03_skomer_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to AB8505 USB */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <16000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "AUX1";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Supplies the Cypress TMA140 touchscreen only with 3.0V */
+						regulator-name = "AUX2";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "AUX3";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "AUX4";
+						/* Hammer to 3.0V for the display */
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "AUX5";
+						/* Intended for 1V8 for touchscreen but actually left unused */
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <2790000>;
+					};
+
+					ab8500_ldo_aux6 {
+						regulator-name = "AUX6";
+						/* Hammer to 1.8V for the display */
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						/* Mostly VIO for sensors */
+						regulator-name = "AUX8";
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				compatible = "sharp,gp2ap002s00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_skomer_default>;
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+
+		/* I2C2 */
+		i2c@80128000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			accel@18 {
+				compatible = "bosch,bma254";
+				clock-frequency = <400000>;
+				reg = <0x18>;
+
+				/* GPIO224 used as "smart alert" interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+
+				mount-matrix = "0", "-1", "0",
+					      "1", "0", "0",
+					       "0", "0", "1";
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bma254_skomer_default>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Cypress CY8CTMA140 touchscreen */
+			touchscreen@20 {
+				compatible = "cypress,cy8ctma140";
+				clock-frequency = <400000>;
+				reg = <0x20>;
+
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				touchscreen-max-pressure = <255>;
+
+				/* GPIO218 for IRQ */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+
+				/* VDD is "digital supply" nominally 1.71-3.6V */
+				vdd-supply = <&ab8500_ldo_aux2_reg>;
+				/* VCPIN is "analog supply", 2.7-3.6 V */
+				vcpin-supply = <&ab8500_ldo_aux2_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&tma140_skomer_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_default_mode>;
+
+			dsi@a0351000 {
+				panel {
+					/* NT35510-based Hydis HVA40WV1 */
+					compatible = "hydis,hva40wv1", "novatek,nt35510";
+					reg = <0>;
+					/* v_lcd_3v0 2.3-4.8V */
+					vdd-supply = <&ab8500_ldo_aux4_reg>;
+					/* v_lcd_1v8 1.65-3.3V */
+					vddi-supply = <&ab8500_ldo_aux6_reg>;
+					/* GPIO 139 */
+					reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&display_default_mode>;
+					backlight = <&ktd253>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	sdi0 {
+		mc0_a_1_default {
+			default_cfg1 {
+				/* GPIO18, 19 & 20 unused so pull down */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	/* This is a reset line for the eMMC */
+	sdi2 {
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	mcde {
+		dsi_default_mode: dsi_default {
+			default_mux1 {
+				/* Mux in VSI0 used for DSI TE */
+				function = "lcd";
+				groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
+			};
+			default_cfg1 {
+				pins = "GPIO68_E1"; /* VSI0 */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	/* Two GPIO lines used by the display */
+	display {
+		display_default_mode: display_default {
+			skomer_cfg1 {
+				/*
+				 * OLED DETECT or check_pba, this appears to be high
+				 * on "PBA" which I guess is "prototype board A".
+				 */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+			skomer_cfg2 {
+				pins = "GPIO139_C9";
+				/*
+				 * MIPI_DSI0_RESET_N resets the display, leave high
+				 * (de-asserted) so we only assert reset explicitly
+				 * from the display driver.
+				 */
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	backlight {
+		gpio_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	flash {
+		gpio_flash_default_mode: flash_default {
+			skomer_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			skomer_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			skomer_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6", /* VOL DOWN */
+				       "GPIO204_AF23", /* MENU */
+				       "GPIO205_AG23"; /* BACK */
+					ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for BMA254 */
+	bma254 {
+		bma254_skomer_default: bma254_skomer {
+			skomer_cfg1 {
+				pins = "GPIO224_AG9";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_skomer_default: gp2ap002_skomer {
+			skomer_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			skomer_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for ALPS HSCD compass */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			skomer_cfg1 {
+				pins = "GPIO151_B17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			skomer_cfg1 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		wlan_en_default_mode: wlan_en_default {
+			skomer_cfg2 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			skomer_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			skomer_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			skomer_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Interrupt line for the Cypress TMA140 touchscreen */
+	touchscreen {
+		tma140_skomer_default: tma140_skomer {
+			skomer_cfg1 {
+				pins = "GPIO218_AH11";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	g05ta03 {
+		g05ta03_skomer_default: g05ta03 {
+			/* Reset line, start out de-asserted */
+			skomer_cfg1 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			skomer_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+};
+
+&ab8505_gpio {
+	/* Hog a few default settings */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio_default>;
+
+	gpio {
+		gpio_default: gpio_default {
+			skomer_mux {
+				/* Change unused pins to GPIO mode */
+				function = "gpio";
+				groups = "gpio3_a_1",	/* default: SysClkReq4 */
+					 "gpio14_a_1";	/* default: PWMOut1 */
+			};
+			skomer_cfg1 {
+				pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/stih407-b2120.dts b/arch/arm/boot/dts/st/stih407-b2120.dts
index 31c85f945c6b..9c79982ee7ba 100644
--- a/arch/arm/boot/dts/stih407-b2120.dts
+++ b/arch/arm/boot/dts/st/stih407-b2120.dts
@@ -11,7 +11,6 @@
 	compatible = "st,stih407-b2120", "st,stih407";
 
 	chosen {
-		bootargs = "clk_ignore_unused";
 		stdout-path = &sbc_serial0;
 	};
 
diff --git a/arch/arm/boot/dts/st/stih407-clock.dtsi b/arch/arm/boot/dts/st/stih407-clock.dtsi
new file mode 100644
index 000000000000..350bcfcf498b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih407-clock.dtsi
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics R&D Limited
+ */
+#include <dt-bindings/clock/stih407-clks.h>
+/ {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * A9 PLL.
+		 */
+		clockgen-a9@92b0000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x92b0000 0x10000>;
+
+			clockgen_a9_pll: clockgen-a9-pll {
+				#clock-cells = <1>;
+				compatible = "st,stih407-clkgen-plla9";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-a@90ff000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x90ff000 0x1000>;
+
+			clk_s_a0_pll: clk-s-a0-pll {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-a0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_a0_flexgen: clk-s-a0-flexgen {
+				compatible = "st,flexgen", "st,flexgen-stih407-a0";
+
+				#clock-cells = <1>;
+
+				clocks = <&clk_s_a0_pll 0>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clk_s_c0: clockgen-c@9103000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9103000 0x1000>;
+
+			clk_s_c0_pll0: clk-s-c0-pll0 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_pll1: clk-s-c0-pll1 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll1-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_flexgen: clk-s-c0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-c0";
+
+				clocks = <&clk_s_c0_pll0 0>,
+					 <&clk_s_c0_pll1 0>,
+					 <&clk_s_c0_quadfs 0>,
+					 <&clk_s_c0_quadfs 1>,
+					 <&clk_s_c0_quadfs 2>,
+					 <&clk_s_c0_quadfs 3>,
+					 <&clk_sysin>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-d0@9104000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9104000 0x1000>;
+
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d0_flexgen: clk-s-d0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d0";
+
+				clocks = <&clk_s_d0_quadfs 0>,
+					 <&clk_s_d0_quadfs 1>,
+					 <&clk_s_d0_quadfs 2>,
+					 <&clk_s_d0_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clockgen-d2@9106000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9106000 0x1000>;
+
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d2_flexgen: clk-s-d2-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d2";
+
+				clocks = <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>,
+					 <&clk_s_d2_quadfs 2>,
+					 <&clk_s_d2_quadfs 3>,
+					 <&clk_sysin>,
+					 <&clk_sysin>,
+					 <&clk_tmdsout_hdmi>;
+			};
+		};
+
+		clockgen-d3@9107000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9107000 0x1000>;
+
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d3_flexgen: clk-s-d3-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d3";
+
+				clocks = <&clk_s_d3_quadfs 0>,
+					 <&clk_s_d3_quadfs 1>,
+					 <&clk_s_d3_quadfs 2>,
+					 <&clk_s_d3_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/st/stih407-family.dtsi
index 7c36c37260a4..29302e74aa1d 100644
--- a/arch/arm/boot/dts/stih407-family.dtsi
+++ b/arch/arm/boot/dts/st/stih407-family.dtsi
@@ -111,41 +111,143 @@
 		regulator-min-microvolt = <784000>;
 		regulator-max-microvolt = <1299000>;
 		regulator-always-on;
-		max-duty-cycle = <255>;
 		status = "okay";
 	};
 
-	soc {
+	restart: restart-controller {
+		compatible = "st,stih407-restart";
+		st,syscfg = <&syscfg_sbc_reg>;
+		status = "okay";
+	};
+
+	powerdown: powerdown-controller {
+		compatible = "st,stih407-powerdown";
+		#reset-cells = <1>;
+	};
+
+	softreset: softreset-controller {
+		compatible = "st,stih407-softreset";
+		#reset-cells = <1>;
+	};
+
+	picophyreset: picophyreset-controller {
+		compatible = "st,stih407-picophyreset";
+		#reset-cells = <1>;
+	};
+
+	irq-syscfg {
+		compatible = "st,stih407-irq-syscfg";
+		st,syscfg = <&syscfg_core>;
+		st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
+				<ST_IRQ_SYSCFG_PMU_1>;
+		st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
+				<ST_IRQ_SYSCFG_DISABLED>;
+	};
+
+	usb2_picophy0: phy1 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0x100 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY2_RESET>;
+		reset-names = "global", "port";
+	};
+
+	miphy28lp_phy: miphy28lp {
+		compatible = "st,miphy28lp-phy";
+		st,syscfg = <&syscfg_core>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		interrupt-parent = <&intc>;
 		ranges;
-		compatible = "simple-bus";
 
-		restart: restart-controller@0 {
-			compatible = "st,stih407-restart";
-			reg = <0 0>;
-			st,syscfg = <&syscfg_sbc_reg>;
-			status = "okay";
-		};
+		phy_port0: port@9b22000 {
+			reg = <0x9b22000 0xff>,
+			      <0x9b09000 0xff>,
+			      <0x9b04000 0xff>;
+			reg-names = "sata-up",
+				    "pcie-up",
+				    "pipew";
 
-		powerdown: powerdown-controller@0 {
-			compatible = "st,stih407-powerdown";
-			reg = <0 0>;
-			#reset-cells = <1>;
+			st,syscfg = <0x114 0x818 0xe0 0xec>;
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
 		};
 
-		softreset: softreset-controller@0 {
-			compatible = "st,stih407-softreset";
-			reg = <0 0>;
-			#reset-cells = <1>;
+		phy_port1: port@9b2a000 {
+			reg = <0x9b2a000 0xff>,
+			      <0x9b19000 0xff>,
+			      <0x9b14000 0xff>;
+			reg-names = "sata-up",
+				    "pcie-up",
+				    "pipew";
+
+			st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
 		};
 
-		picophyreset: picophyreset-controller@0 {
-			compatible = "st,stih407-picophyreset";
-			reg = <0 0>;
-			#reset-cells = <1>;
+		phy_port2: port@8f95000 {
+			reg = <0x8f95000 0xff>,
+			      <0x8f90000 0xff>;
+			reg-names = "pipew",
+				    "usb3-up";
+
+			st,syscfg = <0x11c 0x820>;
+
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
 		};
+	};
+
+	st231_gp0: st231-gp0 {
+		compatible = "st,st231-rproc";
+		memory-region = <&gp0_reserved>;
+		resets = <&softreset STIH407_ST231_GP0_SOFTRESET>;
+		reset-names = "sw_reset";
+		clocks = <&clk_s_c0_flexgen CLK_ST231_GP_0>;
+		clock-frequency = <600000000>;
+		st,syscfg = <&syscfg_core 0x22c>;
+		#mbox-cells = <1>;
+		mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+		mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
+	};
+
+	st231_delta: st231-delta {
+		compatible = "st,st231-rproc";
+		memory-region = <&delta_reserved>;
+		resets = <&softreset STIH407_ST231_DMU_SOFTRESET>;
+		reset-names = "sw_reset";
+		clocks = <&clk_s_c0_flexgen CLK_ST231_DMU>;
+		clock-frequency = <600000000>;
+		st,syscfg = <&syscfg_core 0x224>;
+		#mbox-cells = <1>;
+		mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+		mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
+	};
+
+	delta0 {
+		compatible = "st,st-delta";
+		clock-names = "delta",
+			      "delta-st231",
+			      "delta-flash-promip";
+		clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
+			 <&clk_s_c0_flexgen CLK_ST231_DMU>,
+			 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+		compatible = "simple-bus";
 
 		syscfg_sbc: sbc-syscfg@9620000 {
 			compatible = "st,stih407-sbc-syscfg", "syscon";
@@ -189,16 +291,6 @@
 			reg = <0x94b5100 0x1000>;
 		};
 
-		irq-syscfg@0 {
-			compatible    = "st,stih407-irq-syscfg";
-			reg = <0 0>;
-			st,syscfg     = <&syscfg_core>;
-			st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
-					<ST_IRQ_SYSCFG_PMU_1>;
-			st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
-					<ST_IRQ_SYSCFG_DISABLED>;
-		};
-
 		/* Display */
 		vtg_main: sti-vtg-main@8d02800 {
 			compatible = "st,vtg";
@@ -389,70 +481,6 @@
 			status = "disabled";
 		};
 
-		usb2_picophy0: phy1@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0x100 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY2_RESET>;
-			reset-names = "global", "port";
-		};
-
-		miphy28lp_phy: miphy28lp@0 {
-			compatible = "st,miphy28lp-phy";
-			st,syscfg = <&syscfg_core>;
-			#address-cells	= <1>;
-			#size-cells	= <1>;
-			ranges;
-			reg = <0 0>;
-
-			phy_port0: port@9b22000 {
-				reg = <0x9b22000 0xff>,
-				      <0x9b09000 0xff>,
-				      <0x9b04000 0xff>;
-				reg-names = "sata-up",
-					    "pcie-up",
-					    "pipew";
-
-				st,syscfg = <0x114 0x818 0xe0 0xec>;
-				#phy-cells = <1>;
-
-				reset-names = "miphy-sw-rst";
-				resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
-			};
-
-			phy_port1: port@9b2a000 {
-				reg = <0x9b2a000 0xff>,
-				      <0x9b19000 0xff>,
-				      <0x9b14000 0xff>;
-				reg-names = "sata-up",
-					    "pcie-up",
-					    "pipew";
-
-				st,syscfg = <0x118 0x81c 0xe4 0xf0>;
-
-				#phy-cells = <1>;
-
-				reset-names = "miphy-sw-rst";
-				resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
-			};
-
-			phy_port2: port@8f95000 {
-				reg = <0x8f95000 0xff>,
-				      <0x8f90000 0xff>;
-				reg-names = "pipew",
-					    "usb3-up";
-
-				st,syscfg = <0x11c 0x820>;
-
-				#phy-cells = <1>;
-
-				reset-names = "miphy-sw-rst";
-				resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
-			};
-		};
-
 		spi@9840000 {
 			compatible = "st,comms-ssc4-spi";
 			reg = <0x9840000 0x110>;
@@ -616,6 +644,21 @@
 			st,lpc-mode = <ST_LPC_MODE_CLKSRC>;
 		};
 
+		spifsm: spifsm@9022000 {
+			compatible = "st,spi-fsm";
+			reg = <0x9022000 0x1000>;
+			reg-names = "spi-fsm";
+			clocks = <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+			clock-names = "emi_clk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fsm>;
+			st,syscfg = <&syscfg_core>;
+			st,boot-device-reg = <0x8c4>;
+			st,boot-device-spi = <0x68>;
+
+			status = "disabled";
+		};
+
 		sata0: sata@9b20000 {
 			compatible = "st,ahci";
 			reg = <0x9b20000 0x1000>;
@@ -666,78 +709,78 @@
 
 
 		st_dwc3: dwc3@8f94000 {
-			compatible	= "st,stih407-dwc3";
-			reg		= <0x08f94000 0x1000>, <0x110 0x4>;
-			reg-names	= "reg-glue", "syscfg-reg";
-			st,syscfg	= <&syscfg_core>;
-			resets		= <&powerdown STIH407_USB3_POWERDOWN>,
-					  <&softreset STIH407_MIPHY2_SOFTRESET>;
-			reset-names	= "powerdown", "softreset";
-			#address-cells	= <1>;
-			#size-cells	= <1>;
-			pinctrl-names	= "default";
-			pinctrl-0	= <&pinctrl_usb3>;
+			compatible = "st,stih407-dwc3";
+			reg = <0x08f94000 0x1000>, <0x110 0x4>;
+			reg-names = "reg-glue", "syscfg-reg";
+			st,syscfg = <&syscfg_core>;
+			resets = <&powerdown STIH407_USB3_POWERDOWN>,
+				 <&softreset STIH407_MIPHY2_SOFTRESET>;
+			reset-names = "powerdown", "softreset";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb3>;
 			ranges;
 
 			status = "disabled";
 
-			dwc3: dwc3@9900000 {
-				compatible	= "snps,dwc3";
-				reg		= <0x09900000 0x100000>;
-				interrupts	= <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-				dr_mode		= "host";
-				phy-names	= "usb2-phy", "usb3-phy";
-				phys		= <&usb2_picophy0>,
-						  <&phy_port2 PHY_TYPE_USB3>;
+			dwc3: usb@9900000 {
+				compatible = "snps,dwc3";
+				reg = <0x09900000 0x100000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				phy-names = "usb2-phy", "usb3-phy";
+				phys = <&usb2_picophy0>,
+				       <&phy_port2 PHY_TYPE_USB3>;
 				snps,dis_u3_susphy_quirk;
 			};
 		};
 
 		/* COMMS PWM Module */
 		pwm0: pwm@9810000 {
-			compatible	= "st,sti-pwm";
-			#pwm-cells	= <2>;
-			reg		= <0x9810000 0x68>;
-			interrupts      = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
-			pinctrl-names	= "default";
-			pinctrl-0	= <&pinctrl_pwm0_chan0_default>;
-			clock-names	= "pwm";
-			clocks		= <&clk_sysin>;
+			compatible = "st,sti-pwm";
+			#pwm-cells = <2>;
+			reg = <0x9810000 0x68>;
+			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pwm0_chan0_default>;
+			clock-names = "pwm";
+			clocks = <&clk_sysin>;
 			st,pwm-num-chan = <1>;
 
-			status		= "disabled";
+			status = "disabled";
 		};
 
 		/* SBC PWM Module */
 		pwm1: pwm@9510000 {
-			compatible	= "st,sti-pwm";
-			#pwm-cells	= <2>;
-			reg		= <0x9510000 0x68>;
-			interrupts      = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-			pinctrl-names	= "default";
-			pinctrl-0	= <&pinctrl_pwm1_chan0_default
-					&pinctrl_pwm1_chan1_default
-					&pinctrl_pwm1_chan2_default
-					&pinctrl_pwm1_chan3_default>;
-			clock-names	= "pwm";
-			clocks		= <&clk_sysin>;
+			compatible = "st,sti-pwm";
+			#pwm-cells = <2>;
+			reg = <0x9510000 0x68>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pwm1_chan0_default
+				     &pinctrl_pwm1_chan1_default
+				     &pinctrl_pwm1_chan2_default
+				     &pinctrl_pwm1_chan3_default>;
+			clock-names = "pwm";
+			clocks = <&clk_sysin>;
 			st,pwm-num-chan = <4>;
 
-			status		= "disabled";
+			status = "disabled";
 		};
 
 		rng10: rng@8a89000 {
-			compatible      = "st,rng";
-			reg		= <0x08a89000 0x1000>;
-			clocks          = <&clk_sysin>;
-			status		= "okay";
+			compatible = "st,rng";
+			reg = <0x08a89000 0x1000>;
+			clocks = <&clk_sysin>;
+			status = "okay";
 		};
 
 		rng11: rng@8a8a000 {
-			compatible      = "st,rng";
-			reg		= <0x08a8a000 0x1000>;
-			clocks          = <&clk_sysin>;
-			status		= "okay";
+			compatible = "st,rng";
+			reg = <0x08a8a000 0x1000>;
+			clocks = <&clk_sysin>;
+			status = "okay";
 		};
 
 		ethernet0: dwmac@9630000 {
@@ -767,79 +810,37 @@
 				 <&clk_s_c0_flexgen CLK_ETH_PHY>;
 		};
 
-		rng10: rng@8a89000 {
-			compatible      = "st,rng";
-			reg		= <0x08a89000 0x1000>;
-			clocks          = <&clk_sysin>;
-			status		= "okay";
-		};
-
-		rng11: rng@8a8a000 {
-			compatible      = "st,rng";
-			reg		= <0x08a8a000 0x1000>;
-			clocks          = <&clk_sysin>;
-			status		= "okay";
-		};
-
 		mailbox0: mailbox@8f00000  {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f00000 0x1000>;
-			interrupts	= <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#mbox-cells	= <2>;
-			mbox-name	= "a9";
-			status		= "okay";
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f00000 0x1000>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <2>;
+			mbox-name = "a9";
+			status = "okay";
 		};
 
 		mailbox1: mailbox@8f01000 {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f01000 0x1000>;
-			#mbox-cells	= <2>;
-			mbox-name	= "st231_gp_1";
-			status		= "okay";
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f01000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_gp_1";
+			status = "okay";
 		};
 
 		mailbox2: mailbox@8f02000 {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f02000 0x1000>;
-			#mbox-cells	= <2>;
-			mbox-name	= "st231_gp_0";
-			status		= "okay";
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f02000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_gp_0";
+			status = "okay";
 		};
 
 		mailbox3: mailbox@8f03000 {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f03000 0x1000>;
-			#mbox-cells	= <2>;
-			mbox-name	= "st231_audio_video";
-			status		= "okay";
-		};
-
-		st231_gp0: st231-gp0@0 {
-			compatible	= "st,st231-rproc";
-			reg		= <0 0>;
-			memory-region	= <&gp0_reserved>;
-			resets		= <&softreset STIH407_ST231_GP0_SOFTRESET>;
-			reset-names	= "sw_reset";
-			clocks		= <&clk_s_c0_flexgen CLK_ST231_GP_0>;
-			clock-frequency	= <600000000>;
-			st,syscfg	= <&syscfg_core 0x22c>;
-			#mbox-cells = <1>;
-			mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
-			mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
-		};
-
-		st231_delta: st231-delta@0 {
-			compatible	= "st,st231-rproc";
-			reg		= <0 0>;
-			memory-region	= <&delta_reserved>;
-			resets		= <&softreset STIH407_ST231_DMU_SOFTRESET>;
-			reset-names	= "sw_reset";
-			clocks		= <&clk_s_c0_flexgen CLK_ST231_DMU>;
-			clock-frequency	= <600000000>;
-			st,syscfg	= <&syscfg_core 0x224>;
-			#mbox-cells = <1>;
-			mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
-			mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f03000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_audio_video";
+			status = "okay";
 		};
 
 		/* fdma audio */
@@ -911,7 +912,7 @@
 			dmas = <&fdma0 2 0 1>;
 			dma-names = "tx";
 
-			status		= "disabled";
+			status = "disabled";
 		};
 
 		sti_uni_player1: sti-uni-player@8d81000 {
@@ -985,16 +986,5 @@
 
 			status = "disabled";
 		};
-
-		delta0@0 {
-			compatible = "st,st-delta";
-			reg = <0 0>;
-			clock-names = "delta",
-				      "delta-st231",
-				      "delta-flash-promip";
-			clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
-				 <&clk_s_c0_flexgen CLK_ST231_DMU>,
-				 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
-		};
 	};
 };
diff --git a/arch/arm/boot/dts/stih407-pinctrl.dtsi b/arch/arm/boot/dts/st/stih407-pinctrl.dtsi
index 2cf335714ca2..7815669fe813 100644
--- a/arch/arm/boot/dts/stih407-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stih407-pinctrl.dtsi
@@ -1090,7 +1090,7 @@
 			};
 
 			i2s_out {
-				pinctrl_i2s_8ch_out: i2s_8ch_out{
+				pinctrl_i2s_8ch_out: i2s_8ch_out {
 					st,pins {
 						mclk = <&pio33 5 ALT1 OUT>;
 						lrclk = <&pio33 7 ALT1 OUT>;
@@ -1102,7 +1102,7 @@
 					};
 				};
 
-				pinctrl_i2s_2ch_out: i2s_2ch_out{
+				pinctrl_i2s_2ch_out: i2s_2ch_out {
 					st,pins {
 						mclk = <&pio33 5 ALT1 OUT>;
 						lrclk = <&pio33 7 ALT1 OUT>;
@@ -1113,7 +1113,7 @@
 			};
 
 			i2s_in {
-				pinctrl_i2s_8ch_in: i2s_8ch_in{
+				pinctrl_i2s_8ch_in: i2s_8ch_in {
 					st,pins {
 						mclk = <&pio32 5 ALT1 IN>;
 						lrclk = <&pio32 7 ALT1 IN>;
@@ -1126,7 +1126,7 @@
 					};
 				};
 
-				pinctrl_i2s_2ch_in: i2s_2ch_in{
+				pinctrl_i2s_2ch_in: i2s_2ch_in {
 					st,pins {
 						mclk = <&pio32 5 ALT1 IN>;
 						lrclk = <&pio32 7 ALT1 IN>;
@@ -1137,7 +1137,7 @@
 			};
 
 			spdif_out {
-				pinctrl_spdif_out: spdif_out{
+				pinctrl_spdif_out: spdif_out {
 					st,pins {
 						spdif_out = <&pio34 7 ALT1 OUT>;
 					};
diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/st/stih407.dtsi
index 9e212b0af89d..aca43d2bdaad 100644
--- a/arch/arm/boot/dts/stih407.dtsi
+++ b/arch/arm/boot/dts/st/stih407.dtsi
@@ -13,7 +13,7 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0 0>;
-			assigned-clocks	= <&clk_s_d2_quadfs 0>,
+			assigned-clocks = <&clk_s_d2_quadfs 0>,
 					  <&clk_s_d2_quadfs 1>,
 					  <&clk_s_c0_pll1 0>,
 					  <&clk_s_c0_flexgen CLK_COMPO_DVP>,
@@ -106,7 +106,7 @@
 				reg-names = "hdmi-reg";
 				#sound-dai-cells = <0>;
 				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "irq";
+				interrupt-names = "irq";
 				clock-names = "pix",
 					      "tmds",
 					      "phy",
diff --git a/arch/arm/boot/dts/stih410-b2120.dts b/arch/arm/boot/dts/st/stih410-b2120.dts
index 158b2268748e..538ff98ca1b1 100644
--- a/arch/arm/boot/dts/stih410-b2120.dts
+++ b/arch/arm/boot/dts/st/stih410-b2120.dts
@@ -11,7 +11,6 @@
 	compatible = "st,stih410-b2120", "st,stih410";
 
 	chosen {
-		bootargs = "clk_ignore_unused";
 		stdout-path = &sbc_serial0;
 	};
 
@@ -25,6 +24,14 @@
 		ethernet0 = &ethernet0;
 	};
 
+	usb2_picophy1: phy2 {
+		status = "okay";
+	};
+
+	usb2_picophy2: phy3 {
+		status = "okay";
+	};
+
 	soc {
 
 		mmc0: sdhci@9060000 {
@@ -34,14 +41,6 @@
 			sd-uhs-ddr50;
 		};
 
-		usb2_picophy1: phy2@0 {
-			status = "okay";
-		};
-
-		usb2_picophy2: phy3@0 {
-			status = "okay";
-		};
-
 		ohci0: usb@9a03c00 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/stih410-b2260.dts b/arch/arm/boot/dts/st/stih410-b2260.dts
index 4fbd8e9eb5b7..240b62040000 100644
--- a/arch/arm/boot/dts/stih410-b2260.dts
+++ b/arch/arm/boot/dts/st/stih410-b2260.dts
@@ -12,7 +12,6 @@
 	compatible = "st,stih410-b2260", "st,stih410";
 
 	chosen {
-		bootargs = "clk_ignore_unused";
 		stdout-path = &uart1;
 	};
 
@@ -28,26 +27,26 @@
 
 	leds {
 		compatible = "gpio-leds";
-		user_green_1 {
+		led-user-green-1 {
 			label = "User_green_1";
 			gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
 
-		user_green_2 {
+		led-user-green-2 {
 			label = "User_green_2";
 			gpios = <&pio4 1 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		user_green_3 {
+		led-user-green-3 {
 			label = "User_green_3";
 			gpios = <&pio2 1 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		user_green_4 {
+		led-user-green-4 {
 			label = "User_green_4";
 			gpios = <&pio2 5 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -76,6 +75,21 @@
 		};
 	};
 
+	miphy28lp_phy: miphy28lp {
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
+	usb2_picophy1: phy2 {
+		status = "okay";
+	};
+
+	usb2_picophy2: phy3 {
+		status = "okay";
+	};
+
 	soc {
 		/* Low speed expansion connector */
 		uart0: serial@9830000 {
@@ -146,14 +160,6 @@
 			status = "okay";
 		};
 
-		usb2_picophy1: phy2@0 {
-			status = "okay";
-		};
-
-		usb2_picophy2: phy3@0 {
-			status = "okay";
-		};
-
 		ohci0: usb@9a03c00 {
 			status = "okay";
 		};
@@ -178,9 +184,6 @@
 			phy-mode = "rgmii";
 			pinctrl-0 = <&pinctrl_rgmii1 &pinctrl_rgmii1_mdio_1>;
 
-			snps,phy-bus-name = "stmmac";
-			snps,phy-bus-id = <0>;
-			snps,phy-addr = <0>;
 			snps,reset-gpio = <&pio0 7 0>;
 			snps,reset-active-low;
 			snps,reset-delays-us = <0 10000 1000000>;
@@ -200,13 +203,6 @@
 			status = "okay";
 		};
 
-		miphy28lp_phy: miphy28lp@0 {
-
-			phy_port1: port@9b2a000 {
-				st,osc-force-ext;
-			};
-		};
-
 		sata1: sata@9b28000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/st/stih410-clock.dtsi b/arch/arm/boot/dts/st/stih410-clock.dtsi
new file mode 100644
index 000000000000..abac98a1810b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih410-clock.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics R&D Limited
+ */
+#include <dt-bindings/clock/stih410-clks.h>
+/ {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+		clock-output-names = "CLK_SYSIN";
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		compatible = "st,stih410-clk", "simple-bus";
+
+		/*
+		 * A9 PLL.
+		 */
+		clockgen-a9@92b0000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x92b0000 0x10000>;
+
+			clockgen_a9_pll: clockgen-a9-pll {
+				#clock-cells = <1>;
+				compatible = "st,stih407-clkgen-plla9";
+
+				clocks = <&clk_sysin>;
+			};
+
+			/*
+			 * ARM CPU related clocks.
+			 */
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-a@90ff000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x90ff000 0x1000>;
+
+			clk_s_a0_pll: clk-s-a0-pll {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-a0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_a0_flexgen: clk-s-a0-flexgen {
+				compatible = "st,flexgen", "st,flexgen-stih410-a0";
+
+				#clock-cells = <1>;
+
+				clocks = <&clk_s_a0_pll 0>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clk_s_c0: clockgen-c@9103000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9103000 0x1000>;
+
+			clk_s_c0_pll0: clk-s-c0-pll0 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_pll1: clk-s-c0-pll1 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll1-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_flexgen: clk-s-c0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih410-c0";
+
+				clocks = <&clk_s_c0_pll0 0>,
+					 <&clk_s_c0_pll1 0>,
+					 <&clk_s_c0_quadfs 0>,
+					 <&clk_s_c0_quadfs 1>,
+					 <&clk_s_c0_quadfs 2>,
+					 <&clk_s_c0_quadfs 3>,
+					 <&clk_sysin>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-d0@9104000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9104000 0x1000>;
+
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d0_flexgen: clk-s-d0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih410-d0";
+
+				clocks = <&clk_s_d0_quadfs 0>,
+					 <&clk_s_d0_quadfs 1>,
+					 <&clk_s_d0_quadfs 2>,
+					 <&clk_s_d0_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clockgen-d2@9106000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9106000 0x1000>;
+
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d2_flexgen: clk-s-d2-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d2";
+
+				clocks = <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>,
+					 <&clk_s_d2_quadfs 2>,
+					 <&clk_s_d2_quadfs 3>,
+					 <&clk_sysin>,
+					 <&clk_sysin>,
+					 <&clk_tmdsout_hdmi>;
+			};
+		};
+
+		clockgen-d3@9107000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9107000 0x1000>;
+
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d3_flexgen: clk-s-d3-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d3";
+
+				clocks = <&clk_s_d3_quadfs 0>,
+					 <&clk_s_d3_quadfs 1>,
+					 <&clk_s_d3_quadfs 2>,
+					 <&clk_s_d3_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/stih410-pinctrl.dtsi b/arch/arm/boot/dts/st/stih410-pinctrl.dtsi
index e6eadd124416..e6eadd124416 100644
--- a/arch/arm/boot/dts/stih410-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stih410-pinctrl.dtsi
diff --git a/arch/arm/boot/dts/stih410.dtsi b/arch/arm/boot/dts/st/stih410.dtsi
index 6d847019c554..29e95e9d3229 100644
--- a/arch/arm/boot/dts/stih410.dtsi
+++ b/arch/arm/boot/dts/st/stih410.dtsi
@@ -12,31 +12,29 @@
 		bdisp0 = &bdisp0;
 	};
 
-	soc {
-		usb2_picophy1: phy2@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xf8 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY0_RESET>;
-			reset-names = "global", "port";
-
-			status = "disabled";
-		};
+	usb2_picophy1: phy2 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xf8 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY0_RESET>;
+		reset-names = "global", "port";
+
+		status = "disabled";
+	};
 
-		usb2_picophy2: phy3@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xfc 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY1_RESET>;
-			reset-names = "global", "port";
+	usb2_picophy2: phy3 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xfc 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY1_RESET>;
+		reset-names = "global", "port";
 
-			status = "disabled";
-		};
+		status = "disabled";
+	};
 
+	soc {
 		ohci0: usb@9a03c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
@@ -107,7 +105,7 @@
 			#size-cells = <1>;
 
 			reg = <0 0>;
-			assigned-clocks	= <&clk_s_d2_quadfs 0>,
+			assigned-clocks = <&clk_s_d2_quadfs 0>,
 					  <&clk_s_d2_quadfs 1>,
 					  <&clk_s_c0_pll1 0>,
 					  <&clk_s_c0_flexgen CLK_COMPO_DVP>,
@@ -200,7 +198,7 @@
 				reg-names = "hdmi-reg";
 				#sound-dai-cells = <0>;
 				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "irq";
+				interrupt-names = "irq";
 				clock-names = "pix",
 					      "tmds",
 					      "phy",
@@ -274,17 +272,7 @@
 			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
 		};
 
-		delta0@0 {
-			compatible = "st,st-delta";
-			clock-names = "delta",
-				      "delta-st231",
-				      "delta-flash-promip";
-			clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
-				 <&clk_s_c0_flexgen CLK_ST231_DMU>,
-				 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
-		};
-
-		sti-cec@94a087c {
+		cec@94a087c {
 			compatible = "st,stih-cec";
 			reg = <0x94a087c 0x64>;
 			clocks = <&clk_sysin>;
diff --git a/arch/arm/boot/dts/stih418-b2199.dts b/arch/arm/boot/dts/st/stih418-b2199.dts
index 48c3c64e4c48..53ac6c2b7b7d 100644
--- a/arch/arm/boot/dts/stih418-b2199.dts
+++ b/arch/arm/boot/dts/st/stih418-b2199.dts
@@ -11,7 +11,6 @@
 	compatible = "st,stih418-b2199", "st,stih418";
 
 	chosen {
-		bootargs = "clk_ignore_unused";
 		stdout-path = &sbc_serial0;
 	};
 
@@ -27,17 +26,28 @@
 
 	leds {
 		compatible = "gpio-leds";
-		red {
+		led-red {
 			label = "Front Panel LED";
 			gpios = <&pio4 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
-		green {
+		led-green {
 			gpios = <&pio1 3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 	};
 
+	miphy28lp_phy: miphy28lp {
+
+		phy_port0: port@9b22000 {
+			st,osc-rdy;
+		};
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
 	soc {
 		sbc_serial0: serial@9530000 {
 			status = "okay";
@@ -85,17 +95,6 @@
 			non-removable;
 		};
 
-		miphy28lp_phy: miphy28lp@0 {
-
-			phy_port0: port@9b22000 {
-				st,osc-rdy;
-			};
-
-			phy_port1: port@9b2a000 {
-				st,osc-force-ext;
-			};
-		};
-
 		st_dwc3: dwc3@8f94000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/st/stih418-b2264.dts b/arch/arm/boot/dts/st/stih418-b2264.dts
new file mode 100644
index 000000000000..fdc16e9f5822
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih418-b2264.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 STMicroelectronics
+ * Author: Alain Volmat <avolmat@me.com>
+ */
+/dts-v1/;
+#include "stih418.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	model = "STiH418 B2264";
+	compatible = "st,stih418-b2264", "st,stih418";
+
+	chosen {
+		stdout-path = &sbc_serial0;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0xc0000000>;
+	};
+
+	cpus {
+		cpu@0 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+		cpu@1 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+		cpu@2 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+		cpu@3 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+	};
+
+	cpu_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <784000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <784000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <784000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <784000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <784000>;
+		};
+	};
+
+	aliases {
+		serial0 = &sbc_serial0;
+		ethernet0 = &ethernet0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-green {
+			gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	soc {
+		pin-controller-sbc@961f080 {
+			gmac1 {
+				rgmii1-0 {
+					st,pins {
+						rxd0 = <&pio1 4 ALT1 IN DE_IO 300 CLK_A>;
+						rxd1 = <&pio1 5 ALT1 IN DE_IO 300 CLK_A>;
+						rxd2 = <&pio1 6 ALT1 IN DE_IO 300 CLK_A>;
+						rxd3 = <&pio1 7 ALT1 IN DE_IO 300 CLK_A>;
+						rxdv = <&pio2 0 ALT1 IN DE_IO 300 CLK_A>;
+					};
+				};
+			};
+		};
+
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ethernet0 {
+	phy-mode = "rgmii";
+	pinctrl-0 = <&pinctrl_rgmii1 &pinctrl_rgmii1_mdio_1>;
+	st,tx-retime-src = "clkgen";
+
+	snps,reset-gpio = <&pio0 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+
+	status = "okay";
+};
+
+&miphy28lp_phy {
+	phy_port0: port@9b22000 {
+		st,sata-gen = <2>; /* SATA GEN3 */
+		st,osc-rdy;
+	};
+};
+
+&mmc0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&sata0 {
+	status = "okay";
+};
+
+&sbc_serial0 {
+	status = "okay";
+};
+
+&spifsm {
+	status = "okay";
+};
+
+&st_dwc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stih418-clock.dtsi b/arch/arm/boot/dts/st/stih418-clock.dtsi
new file mode 100644
index 000000000000..e1749e92a2e7
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih418-clock.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 STMicroelectronics R&D Limited
+ */
+#include <dt-bindings/clock/stih418-clks.h>
+/ {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+		clock-output-names = "CLK_SYSIN";
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		compatible = "st,stih418-clk", "simple-bus";
+
+		/*
+		 * A9 PLL.
+		 */
+		clockgen-a9@92b0000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x92b0000 0x10000>;
+
+			clockgen_a9_pll: clockgen-a9-pll {
+				#clock-cells = <1>;
+				compatible = "st,stih418-clkgen-plla9";
+
+				clocks = <&clk_sysin>;
+			};
+
+			/*
+			 * ARM CPU related clocks.
+			 */
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-a@90ff000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x90ff000 0x1000>;
+
+			clk_s_a0_pll: clk-s-a0-pll {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-a0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_a0_flexgen: clk-s-a0-flexgen {
+				compatible = "st,flexgen", "st,flexgen-stih410-a0";
+
+				#clock-cells = <1>;
+
+				clocks = <&clk_s_a0_pll 0>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clk_s_c0: clockgen-c@9103000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9103000 0x1000>;
+
+			clk_s_c0_pll0: clk-s-c0-pll0 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_pll1: clk-s-c0-pll1 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll1-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_flexgen: clk-s-c0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih418-c0";
+
+				clocks = <&clk_s_c0_pll0 0>,
+					 <&clk_s_c0_pll1 0>,
+					 <&clk_s_c0_quadfs 0>,
+					 <&clk_s_c0_quadfs 1>,
+					 <&clk_s_c0_quadfs 2>,
+					 <&clk_s_c0_quadfs 3>,
+					 <&clk_sysin>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-d0@9104000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9104000 0x1000>;
+
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d0_flexgen: clk-s-d0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih410-d0";
+
+				clocks = <&clk_s_d0_quadfs 0>,
+					 <&clk_s_d0_quadfs 1>,
+					 <&clk_s_d0_quadfs 2>,
+					 <&clk_s_d0_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clockgen-d2@9106000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9106000 0x1000>;
+
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d2_flexgen: clk-s-d2-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih418-d2";
+
+				clocks = <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>,
+					 <&clk_s_d2_quadfs 2>,
+					 <&clk_s_d2_quadfs 3>,
+					 <&clk_sysin>,
+					 <&clk_sysin>,
+					 <&clk_tmdsout_hdmi>;
+			};
+		};
+
+		clockgen-d3@9107000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9107000 0x1000>;
+
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d3_flexgen: clk-s-d3-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d3";
+
+				clocks = <&clk_s_d3_quadfs 0>,
+					 <&clk_s_d3_quadfs 1>,
+					 <&clk_s_d3_quadfs 2>,
+					 <&clk_s_d3_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/stih418.dtsi b/arch/arm/boot/dts/st/stih418.dtsi
index 83411322bd92..b35b9b7a7ccc 100644
--- a/arch/arm/boot/dts/stih418.dtsi
+++ b/arch/arm/boot/dts/st/stih418.dtsi
@@ -26,31 +26,33 @@
 		};
 	};
 
-	soc {
-		usb2_picophy1: phy2@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xf8 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY0_RESET>;
-			reset-names = "global", "port";
-		};
+	usb2_picophy1: phy2 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xf8 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY0_RESET>;
+		reset-names = "global", "port";
+	};
+
+	usb2_picophy2: phy3 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xfc 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY1_RESET>;
+		reset-names = "global", "port";
+	};
 
-		usb2_picophy2: phy3@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xfc 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY1_RESET>;
-			reset-names = "global", "port";
+	soc {
+		rng11: rng@8a8a000 {
+			status = "disabled";
 		};
 
 		ohci0: usb@9a03c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
-			interrupts = <GIC_SPI 180 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
@@ -62,7 +64,7 @@
 		ehci0: usb@9a03e00 {
 			compatible = "st,st-ehci-300x";
 			reg = <0x9a03e00 0x100>;
-			interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
@@ -76,7 +78,7 @@
 		ohci1: usb@9a83c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a83c00 0x100>;
-			interrupts = <GIC_SPI 181 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
 			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
 				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
@@ -88,7 +90,7 @@
 		ehci1: usb@9a83e00 {
 			compatible = "st,st-ehci-300x";
 			reg = <0x9a83e00 0x100>;
-			interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
@@ -104,5 +106,13 @@
 			assigned-clock-parents = <&clk_s_c0_pll1 0>;
 			assigned-clock-rates = <200000000>;
 		};
+
+		thermal@91a0000 {
+			compatible = "st,stih407-thermal";
+			reg = <0x91a0000 0x28>;
+			clock-names = "thermal";
+			clocks = <&clk_sysin>;
+			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/stihxxx-b2120.dtsi b/arch/arm/boot/dts/st/stihxxx-b2120.dtsi
index 60e11045ad76..8d9a2dfa76f1 100644
--- a/arch/arm/boot/dts/stihxxx-b2120.dtsi
+++ b/arch/arm/boot/dts/st/stihxxx-b2120.dtsi
@@ -9,12 +9,12 @@
 / {
 	leds {
 		compatible = "gpio-leds";
-		red {
+		led-red {
 			label = "Front Panel LED";
 			gpios = <&pio4 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
-		green {
+		led-green {
 			gpios = <&pio1 3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
@@ -46,7 +46,7 @@
 			/* DAC */
 			format = "i2s";
 			mclk-fs = <256>;
-			frame-inversion = <1>;
+			frame-inversion;
 			cpu {
 				sound-dai = <&sti_uni_player2>;
 			};
@@ -71,6 +71,17 @@
 		};
 	};
 
+	miphy28lp_phy: miphy28lp {
+
+		phy_port0: port@9b22000 {
+			st,osc-rdy;
+		};
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
 	soc {
 		sbc_serial0: serial@9530000 {
 			status = "okay";
@@ -128,17 +139,6 @@
 			st,i2c-min-sda-pulse-width-us = <5>;
 		};
 
-		miphy28lp_phy: miphy28lp@0 {
-
-			phy_port0: port@9b22000 {
-				st,osc-rdy;
-			};
-
-			phy_port1: port@9b2a000 {
-				st,osc-force-ext;
-			};
-		};
-
 		st_dwc3: dwc3@8f94000 {
 			status = "okay";
 		};
@@ -175,11 +175,11 @@
 
 			/* tsin0 is TSA on NIMA */
 			tsin0: port {
-				tsin-num	= <0>;
+				tsin-num = <0>;
 				serial-not-parallel;
-				i2c-bus		= <&ssc2>;
-				reset-gpios	= <&pio15 4 GPIO_ACTIVE_HIGH>;
-				dvb-card	= <STV0367_TDA18212_NIMA_1>;
+				i2c-bus = <&ssc2>;
+				reset-gpios = <&pio15 4 GPIO_ACTIVE_LOW>;
+				dvb-card = <STV0367_TDA18212_NIMA_1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/stm32429i-eval.dts b/arch/arm/boot/dts/st/stm32429i-eval.dts
index 58288aa53fee..576235ec3c51 100644
--- a/arch/arm/boot/dts/stm32429i-eval.dts
+++ b/arch/arm/boot/dts/st/stm32429i-eval.dts
@@ -50,6 +50,7 @@
 #include "stm32f429-pinctrl.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
 
 / {
 	model = "STMicroelectronics STM32429i-EVAL board";
@@ -60,7 +61,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory@00000000 {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x2000000>;
 	};
@@ -95,34 +96,39 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
+	vdd_panel: vdd-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
-		green {
+		led-green {
 			gpios = <&gpiog 6 1>;
 			linux,default-trigger = "heartbeat";
 		};
-		orange {
+		led-orange {
 			gpios = <&gpiog 7 1>;
 		};
-		red {
+		led-red {
 			gpios = <&gpiog 10 1>;
 		};
-		blue {
+		led-blue {
 			gpios = <&gpiog 12 1>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 0>;
 		};
-		button@1 {
+		button-1 {
 			label = "Tamper";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioc 13 0>;
@@ -138,6 +144,7 @@
 
 	panel_rgb: panel-rgb {
 		compatible = "ampire,am-480272h3tmqw-t01h";
+		power-supply = <&vdd_panel>;
 		status = "okay";
 		port {
 			panel_in_rgb: endpoint {
@@ -180,6 +187,7 @@
 	port {
 		dcmi_0: endpoint {
 			remote-endpoint = <&ov2640_0>;
+			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
 			bus-width = <8>;
 			hsync-active = <0>;
 			vsync-active = <0>;
@@ -232,7 +240,7 @@
 
 &ltdc {
 	status = "okay";
-	pinctrl-0 = <&ltdc_pins>;
+	pinctrl-0 = <&ltdc_pins_a>;
 	pinctrl-names = "default";
 
 	port {
@@ -244,10 +252,10 @@
 
 &mac {
 	status = "okay";
-	pinctrl-0	= <&ethernet_mii>;
-	pinctrl-names	= "default";
-	phy-mode	= "mii";
-	phy-handle	= <&phy1>;
+	pinctrl-0 = <&ethernet_mii>;
+	pinctrl-names = "default";
+	phy-mode = "mii";
+	phy-handle = <&phy1>;
 	mdio0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -301,6 +309,18 @@
 	};
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32746g-eval.dts b/arch/arm/boot/dts/st/stm32746g-eval.dts
index fcc804e3c158..e9ac37b6eca0 100644
--- a/arch/arm/boot/dts/stm32746g-eval.dts
+++ b/arch/arm/boot/dts/st/stm32746g-eval.dts
@@ -66,27 +66,25 @@
 
 	leds {
 		compatible = "gpio-leds";
-		green {
+		led-green {
 			gpios = <&gpiof 10 1>;
 			linux,default-trigger = "heartbeat";
 		};
-		orange {
+		led-orange {
 			gpios = <&stmfx_pinctrl 17 1>;
 		};
-		red {
+		led-red {
 			gpios = <&gpiob 7 1>;
 		};
-		blue {
+		led-blue {
 			gpios = <&stmfx_pinctrl 19 1>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioc 13 0>;
@@ -165,7 +163,7 @@
 		interrupts = <8 IRQ_TYPE_EDGE_RISING>;
 		interrupt-parent = <&gpioi>;
 
-		stmfx_pinctrl: stmfx-pin-controller {
+		stmfx_pinctrl: pinctrl {
 			compatible = "st,stmfx-0300-pinctrl";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -190,12 +188,25 @@
 	status = "okay";
 	vmmc-supply = <&mmc_vcard>;
 	broken-cd;
-	pinctrl-names = "default", "opendrain";
+	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdio_pins_a>;
 	pinctrl-1 = <&sdio_pins_od_a>;
+	pinctrl-2 = <&sdio_pins_sleep_a>;
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f4-pinctrl.dtsi
index 35202896c093..3bb812d6399e 100644
--- a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32f4-pinctrl.dtsi
@@ -45,13 +45,12 @@
 
 / {
 	soc {
-		pinctrl: pin-controller {
+		pinctrl: pinctrl@40020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x40020000 0x3000>;
 			interrupt-parent = <&exti>;
 			st,syscfg = <&syscfg 0x8>;
-			pins-are-numbered;
 
 			gpioa: gpio@40020000 {
 				gpio-controller;
@@ -163,7 +162,7 @@
 				st,bank-name = "GPIOK";
 			};
 
-			usart1_pins_a: usart1@0 {
+			usart1_pins_a: usart1-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */
 					bias-disable;
@@ -176,7 +175,7 @@
 				};
 			};
 
-			usart3_pins_a: usart3@0 {
+			usart3_pins_a: usart3-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
 					bias-disable;
@@ -189,7 +188,7 @@
 				};
 			};
 
-			usbotg_fs_pins_a: usbotg_fs@0 {
+			usbotg_fs_pins_a: usbotg-fs-0 {
 				pins {
 					pinmux = <STM32_PINMUX('A', 10, AF10)>, /* OTG_FS_ID */
 						 <STM32_PINMUX('A', 11, AF10)>, /* OTG_FS_DM */
@@ -200,7 +199,7 @@
 				};
 			};
 
-			usbotg_fs_pins_b: usbotg_fs@1 {
+			usbotg_fs_pins_b: usbotg-fs-1 {
 				pins {
 					pinmux = <STM32_PINMUX('B', 12, AF12)>, /* OTG_HS_ID */
 						 <STM32_PINMUX('B', 14, AF12)>, /* OTG_HS_DM */
@@ -211,7 +210,7 @@
 				};
 			};
 
-			usbotg_hs_pins_a: usbotg_hs@0 {
+			usbotg_hs_pins_a: usbotg-hs-0 {
 				pins {
 					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT*/
 						 <STM32_PINMUX('I', 11, AF10)>, /* OTG_HS_ULPI_DIR */
@@ -231,7 +230,7 @@
 				};
 			};
 
-			ethernet_mii: mii@0 {
+			ethernet_mii: mii-0 {
 				pins {
 					pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH_MII_TXD0_ETH_RMII_TXD0 */
 						 <STM32_PINMUX('G', 14, AF11)>, /* ETH_MII_TXD1_ETH_RMII_TXD1 */
@@ -251,13 +250,13 @@
 				};
 			};
 
-			adc3_in8_pin: adc@200 {
+			adc3_in8_pin: adc-200 {
 				pins {
 					pinmux = <STM32_PINMUX('F', 10, ANALOG)>;
 				};
 			};
 
-			pwm1_pins: pwm@1 {
+			pwm1_pins: pwm1-0 {
 				pins {
 					pinmux = <STM32_PINMUX('A', 8, AF1)>, /* TIM1_CH1 */
 						 <STM32_PINMUX('B', 13, AF1)>, /* TIM1_CH1N */
@@ -265,14 +264,14 @@
 				};
 			};
 
-			pwm3_pins: pwm@3 {
+			pwm3_pins: pwm3-0 {
 				pins {
 					pinmux = <STM32_PINMUX('B', 4, AF2)>, /* TIM3_CH1 */
 						 <STM32_PINMUX('B', 5, AF2)>; /* TIM3_CH2 */
 				};
 			};
 
-			i2c1_pins: i2c1@0 {
+			i2c1_pins: i2c1-0 {
 				pins {
 					pinmux = <STM32_PINMUX('B', 9, AF4)>, /* I2C1_SDA */
 						 <STM32_PINMUX('B', 6, AF4)>; /* I2C1_SCL */
@@ -282,7 +281,7 @@
 				};
 			};
 
-			ltdc_pins: ltdc@0 {
+			ltdc_pins_a: ltdc-0 {
 				pins {
 					pinmux = <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */
 						 <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */
@@ -316,7 +315,86 @@
 				};
 			};
 
-			dcmi_pins: dcmi@0 {
+			ltdc_pins_b: ltdc-1 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 6,  AF14)>,
+						/* LCD_HSYNC */
+						 <STM32_PINMUX('A', 4,  AF14)>,
+						 /* LCD_VSYNC */
+						 <STM32_PINMUX('G', 7,  AF14)>,
+						 /* LCD_CLK */
+						 <STM32_PINMUX('C', 10, AF14)>,
+						 /* LCD_R2 */
+						 <STM32_PINMUX('B', 0,  AF9)>,
+						 /* LCD_R3 */
+						 <STM32_PINMUX('A', 11, AF14)>,
+						 /* LCD_R4 */
+						 <STM32_PINMUX('A', 12, AF14)>,
+						 /* LCD_R5 */
+						 <STM32_PINMUX('B', 1,  AF9)>,
+						 /* LCD_R6*/
+						 <STM32_PINMUX('G', 6,  AF14)>,
+						 /* LCD_R7 */
+						 <STM32_PINMUX('A', 6,  AF14)>,
+						 /* LCD_G2 */
+						 <STM32_PINMUX('G', 10, AF9)>,
+						 /* LCD_G3 */
+						 <STM32_PINMUX('B', 10, AF14)>,
+						 /* LCD_G4 */
+						 <STM32_PINMUX('D', 6,  AF14)>,
+						 /* LCD_B2 */
+						 <STM32_PINMUX('G', 11, AF14)>,
+						 /* LCD_B3*/
+						 <STM32_PINMUX('B', 11, AF14)>,
+						 /* LCD_G5 */
+						 <STM32_PINMUX('C', 7,  AF14)>,
+						 /* LCD_G6 */
+						 <STM32_PINMUX('D', 3,  AF14)>,
+						 /* LCD_G7 */
+						 <STM32_PINMUX('G', 12, AF9)>,
+						 /* LCD_B4 */
+						 <STM32_PINMUX('A', 3,  AF14)>,
+						 /* LCD_B5 */
+						 <STM32_PINMUX('B', 8,  AF14)>,
+						 /* LCD_B6 */
+						 <STM32_PINMUX('B', 9,  AF14)>,
+						 /* LCD_B7 */
+						 <STM32_PINMUX('F', 10, AF14)>;
+						 /* LCD_DE */
+					slew-rate = <2>;
+				};
+			};
+
+			spi5_pins: spi5-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('F', 7, AF5)>,
+						/* SPI5_CLK */
+						 <STM32_PINMUX('F', 9, AF5)>;
+						/* SPI5_MOSI */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('F', 8, AF5)>;
+						/* SPI5_MISO */
+					bias-disable;
+				};
+			};
+
+			i2c3_pins: i2c3-0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 9, AF4)>,
+						/* I2C3_SDA */
+						 <STM32_PINMUX('A', 8, AF4)>;
+						/* I2C3_SCL */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <3>;
+				};
+			};
+
+			dcmi_pins: dcmi-0 {
 				pins {
 					pinmux = <STM32_PINMUX('A', 4, AF13)>, /* DCMI_HSYNC */
 						 <STM32_PINMUX('B', 7, AF13)>, /* DCMI_VSYNC */
@@ -339,7 +417,7 @@
 				};
 			};
 
-			sdio_pins: sdio_pins@0 {
+			sdio_pins: sdio-pins-0 {
 				pins {
 					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDIO_D0 */
 						 <STM32_PINMUX('C', 9, AF12)>, /* SDIO_D1 */
@@ -352,7 +430,7 @@
 				};
 			};
 
-			sdio_pins_od: sdio_pins_od@0 {
+			sdio_pins_od: sdio-pins-od-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDIO_D0 */
 						 <STM32_PINMUX('C', 9, AF12)>, /* SDIO_D1 */
@@ -369,6 +447,36 @@
 					slew-rate = <2>;
 				};
 			};
+
+			can1_pins_a: can1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 9, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 8, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_a: can2-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_b: can2-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 12, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/st/stm32f429-disco.dts
index 30c0f6717871..a3cb4aabdd5a 100644
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f429-disco.dts
@@ -49,6 +49,8 @@
 #include "stm32f429.dtsi"
 #include "stm32f429-pinctrl.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "STMicroelectronics STM32F429i-DISCO board";
@@ -70,21 +72,19 @@
 
 	leds {
 		compatible = "gpio-leds";
-		red {
+		led-red {
 			gpios = <&gpiog 14 0>;
 		};
-		green {
+		led-green {
 			gpios = <&gpiog 13 0>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 0>;
@@ -108,12 +108,115 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	stmpe811@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioa>;
+		/* 3.25 MHz ADC clock speed */
+		st,adc-freq = <1>;
+		/* 12-bit ADC */
+		st,mod-12b = <1>;
+		/* internal ADC reference */
+		st,ref-sel = <0>;
+		/* ADC converstion time: 80 clocks */
+		st,sample-time = <4>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			/* 8 sample average control */
+			st,ave-ctrl = <3>;
+			/* 7 length fractional part in z */
+			st,fraction-z = <7>;
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			/* 1 ms panel driver settling time */
+			st,settling = <3>;
+			/* 5 ms touch detect interrupt delay */
+			st,touch-det-delay = <5>;
+		};
+
+		stmpe_adc {
+			compatible = "st,stmpe-adc";
+			/* forbid to use ADC channels 3-0 (touch) */
+			st,norequest-mask = <0x0F>;
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-names = "default";
+
+	port {
+		ltdc_out_rgb: endpoint {
+			remote-endpoint = <&panel_in_rgb>;
+		};
+	};
+};
+
 &rtc {
 	assigned-clocks = <&rcc 1 CLK_RTC>;
 	assigned-clock-parents = <&rcc 1 CLK_LSI>;
 	status = "okay";
 };
 
+&spi5 {
+	status = "okay";
+	pinctrl-0 = <&spi5_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpioc 1 GPIO_ACTIVE_LOW>, <&gpioc 2 GPIO_ACTIVE_LOW>;
+
+	l3gd20: l3gd20@0 {
+		compatible = "st,l3gd20-gyro";
+		spi-max-frequency = <10000000>;
+		st,drdy-int-pin = <2>;
+		interrupt-parent = <&gpioa>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>,
+				<2 IRQ_TYPE_EDGE_RISING>;
+		reg = <0>;
+		status = "okay";
+	};
+
+	display: display@1 {
+		/* Connect panel-ilitek-9341 to ltdc */
+		compatible = "st,sf-tc240t-9370-t", "ilitek,ili9341";
+		reg = <1>;
+		spi-3wire;
+		spi-max-frequency = <10000000>;
+		dc-gpios = <&gpiod 13 0>;
+		port {
+			panel_in_rgb: endpoint {
+			remote-endpoint = <&ltdc_out_rgb>;
+			};
+		};
+	};
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f429-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f429-pinctrl.dtsi
index 3e7a17d9112e..e10d7a1f3207 100644
--- a/arch/arm/boot/dts/stm32f429-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32f429-pinctrl.dtsi
@@ -42,54 +42,50 @@
 
 #include "stm32f4-pinctrl.dtsi"
 
-/ {
-	soc {
-		pinctrl: pin-controller {
-			compatible = "st,stm32f429-pinctrl";
+&pinctrl {
+	compatible = "st,stm32f429-pinctrl";
 
-			gpioa: gpio@40020000 {
-				gpio-ranges = <&pinctrl 0 0 16>;
-			};
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
 
-			gpiob: gpio@40020400 {
-				gpio-ranges = <&pinctrl 0 16 16>;
-			};
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
 
-			gpioc: gpio@40020800 {
-				gpio-ranges = <&pinctrl 0 32 16>;
-			};
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
 
-			gpiod: gpio@40020c00 {
-				gpio-ranges = <&pinctrl 0 48 16>;
-			};
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
 
-			gpioe: gpio@40021000 {
-				gpio-ranges = <&pinctrl 0 64 16>;
-			};
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
 
-			gpiof: gpio@40021400 {
-				gpio-ranges = <&pinctrl 0 80 16>;
-			};
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
 
-			gpiog: gpio@40021800 {
-				gpio-ranges = <&pinctrl 0 96 16>;
-			};
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
 
-			gpioh: gpio@40021c00 {
-				gpio-ranges = <&pinctrl 0 112 16>;
-			};
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
 
-			gpioi: gpio@40022000 {
-				gpio-ranges = <&pinctrl 0 128 16>;
-			};
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
 
-			gpioj: gpio@40022400 {
-				gpio-ranges = <&pinctrl 0 144 16>;
-			};
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
 
-			gpiok: gpio@40022800 {
-				gpio-ranges = <&pinctrl 0 160 8>;
-			};
-		};
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 0 160 8>;
 	};
 };
diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/st/stm32f429.dtsi
index 5c8a826b3195..8efcda9ef8ae 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/st/stm32f429.dtsi
@@ -45,7 +45,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../armv7-m.dtsi"
 #include <dt-bindings/clock/stm32fx-clock.h>
 #include <dt-bindings/mfd/stm32f4-rcc.h>
 
@@ -80,7 +80,7 @@
 	};
 
 	soc {
-		romem: nvmem@1fff7800 {
+		romem: efuse@1fff7800 {
 			compatible = "st,stm32f4-otp";
 			reg = <0x1fff7800 0x400>;
 			#address-cells = <1>;
@@ -93,14 +93,6 @@
 			};
 		};
 
-		timer2: timer@40000000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000000 0x400>;
-			interrupts = <28>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM2)>;
-			status = "disabled";
-		};
-
 		timers2: timers@40000000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -123,14 +115,6 @@
 			};
 		};
 
-		timer3: timer@40000400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000400 0x400>;
-			interrupts = <29>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM3)>;
-			status = "disabled";
-		};
-
 		timers3: timers@40000400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -153,14 +137,6 @@
 			};
 		};
 
-		timer4: timer@40000800 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000800 0x400>;
-			interrupts = <30>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM4)>;
-			status = "disabled";
-		};
-
 		timers4: timers@40000800 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -183,13 +159,6 @@
 			};
 		};
 
-		timer5: timer@40000c00 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000c00 0x400>;
-			interrupts = <50>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM5)>;
-		};
-
 		timers5: timers@40000c00 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -212,14 +181,6 @@
 			};
 		};
 
-		timer6: timer@40001000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001000 0x400>;
-			interrupts = <54>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM6)>;
-			status = "disabled";
-		};
-
 		timers6: timers@40001000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -236,14 +197,6 @@
 			};
 		};
 
-		timer7: timer@40001400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001400 0x400>;
-			interrupts = <55>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM7)>;
-			status = "disabled";
-		};
-
 		timers7: timers@40001400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -283,8 +236,6 @@
 		};
 
 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM13)>;
@@ -299,8 +250,6 @@
 		};
 
 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM14)>;
@@ -318,12 +267,10 @@
 			compatible = "st,stm32-rtc";
 			reg = <0x40002800 0x400>;
 			clocks = <&rcc 1 CLK_RTC>;
-			clock-names = "ck_rtc";
 			assigned-clocks = <&rcc 1 CLK_RTC>;
 			assigned-clock-parents = <&rcc 1 CLK_LSE>;
 			interrupt-parent = <&exti>;
 			interrupts = <17 1>;
-			interrupt-names = "alarm";
 			st,syscfg = <&pwrcfg 0x00 0x100>;
 			status = "disabled";
 		};
@@ -403,6 +350,48 @@
 			status = "disabled";
 		};
 
+		i2c3: i2c@40005c00 {
+			compatible = "st,stm32f4-i2c";
+			reg = <0x40005c00 0x400>;
+			interrupts = <72>,
+				     <73>;
+			resets = <&rcc STM32F4_APB1_RESET(I2C3)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C3)>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		can1: can@40006400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006400 0x200>;
+			interrupts = <19>, <20>, <21>, <22>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F4_APB1_RESET(CAN1)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
+			st,can-primary;
+			st,gcan = <&gcan>;
+			status = "disabled";
+		};
+
+		gcan: gcan@40006600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40006600 0x200>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
+		};
+
+		can2: can@40006800 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006800 0x200>;
+			interrupts = <63>, <64>, <65>, <66>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F4_APB1_RESET(CAN2)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN2)>;
+			st,can-secondary;
+			st,gcan = <&gcan>;
+			status = "disabled";
+		};
+
 		dac: dac@40007400 {
 			compatible = "st,stm32f4-dac-core";
 			reg = <0x40007400 0x400>;
@@ -415,14 +404,14 @@
 
 			dac1: dac@1 {
 				compatible = "st,stm32-dac";
-				#io-channels-cells = <1>;
+				#io-channel-cells = <1>;
 				reg = <1>;
 				status = "disabled";
 			};
 
 			dac2: dac@2 {
 				compatible = "st,stm32-dac";
-				#io-channels-cells = <1>;
+				#io-channel-cells = <1>;
 				reg = <2>;
 				status = "disabled";
 			};
@@ -556,7 +545,7 @@
 			};
 		};
 
-		sdio: sdio@40012c00 {
+		sdio: mmc@40012c00 {
 			compatible = "arm,pl180", "arm,primecell";
 			arm,primecell-periphid = <0x00880180>;
 			reg = <0x40012c00 0x400>;
@@ -587,8 +576,8 @@
 			status = "disabled";
 		};
 
-		syscfg: system-config@40013800 {
-			compatible = "syscon";
+		syscfg: syscon@40013800 {
+			compatible = "st,stm32-syscfg", "syscon";
 			reg = <0x40013800 0x400>;
 		};
 
@@ -623,8 +612,6 @@
 		};
 
 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM10)>;
@@ -639,8 +626,6 @@
 		};
 
 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM11)>;
@@ -661,6 +646,9 @@
 			reg = <0x40015000 0x400>;
 			interrupts = <85>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(SPI5)>;
+			dmas = <&dma2 3 2 0x400 0x0>,
+				<&dma2 4 2 0x400 0x0>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -675,7 +663,7 @@
 		};
 
 		pwrcfg: power-config@40007000 {
-			compatible = "syscon";
+			compatible = "st,stm32-power-config", "syscon";
 			reg = <0x40007000 0x400>;
 		};
 
@@ -696,7 +684,7 @@
 			status = "disabled";
 		};
 
-		rcc: rcc@40023810 {
+		rcc: rcc@40023800 {
 			#reset-cells = <1>;
 			#clock-cells = <2>;
 			compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
@@ -754,6 +742,16 @@
 			status = "disabled";
 		};
 
+		dma2d: dma2d@4002b000 {
+			compatible = "st,stm32-dma2d";
+			reg = <0x4002b000 0xc00>;
+			interrupts = <90>;
+			resets = <&rcc STM32F4_AHB1_RESET(DMA2D)>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA2D)>;
+			clock-names = "dma2d";
+			status = "disabled";
+		};
+
 		usbotg_hs: usb@40040000 {
 			compatible = "snps,dwc2";
 			reg = <0x40040000 0x40000>;
@@ -789,7 +787,6 @@
 		rng: rng@50060800 {
 			compatible = "st,stm32-rng";
 			reg = <0x50060800 0x400>;
-			interrupts = <80>;
 			clocks = <&rcc 0 STM32F4_AHB2_CLOCK(RNG)>;
 
 		};
diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/st/stm32f469-disco.dts
index f3ce477b7bae..8a4f8ddd083d 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f469-disco.dts
@@ -60,7 +60,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory@00000000 {
+	memory@0 {
 		device_type = "memory";
 		reg = <0x00000000 0x1000000>;
 	};
@@ -69,9 +69,9 @@
 		serial0 = &usart3;
 	};
 
-	mmc_vcard: mmc_vcard {
+	vcc_3v3: vcc-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "mmc_vcard";
+		regulator-name = "vcc_3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
@@ -82,27 +82,25 @@
 
 	leds {
 		compatible = "gpio-leds";
-		green {
+		led-green {
 			gpios = <&gpiog 6 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
-		orange {
+		led-orange {
 			gpios = <&gpiod 4 GPIO_ACTIVE_LOW>;
 		};
-		red {
+		led-red {
 			gpios = <&gpiod 5 GPIO_ACTIVE_LOW>;
 		};
-		blue {
+		led-blue {
 			gpios = <&gpiok 3 GPIO_ACTIVE_LOW>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
@@ -127,6 +125,10 @@
 	clock-frequency = <8000000>;
 };
 
+&dma2d {
+	status = "okay";
+};
+
 &dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -151,10 +153,11 @@
 		};
 	};
 
-	panel-dsi@0 {
+	panel@0 {
 		compatible = "orisetech,otm8009a";
 		reg = <0>; /* dsi virtual channel (0..3) */
 		reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>;
+		power-supply = <&vcc_3v3>;
 		status = "okay";
 
 		port {
@@ -169,7 +172,7 @@
 	status = "okay";
 
 	port {
-		ltdc_out_dsi: endpoint@0 {
+		ltdc_out_dsi: endpoint {
 			remote-endpoint = <&dsi_in>;
 		};
 	};
@@ -209,7 +212,7 @@
 
 &sdio {
 	status = "okay";
-	vmmc-supply = <&mmc_vcard>;
+	vmmc-supply = <&vcc_3v3>;
 	cd-gpios = <&gpiog 2 GPIO_ACTIVE_LOW>;
 	broken-cd;
 	pinctrl-names = "default", "opendrain";
@@ -218,6 +221,18 @@
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart3 {
 	pinctrl-0 = <&usart3_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f469-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f469-pinctrl.dtsi
index fff542662eea..6bf60263dff8 100644
--- a/arch/arm/boot/dts/stm32f469-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32f469-pinctrl.dtsi
@@ -42,55 +42,51 @@
 
 #include "stm32f4-pinctrl.dtsi"
 
-/ {
-	soc {
-		pinctrl: pin-controller {
-			compatible = "st,stm32f469-pinctrl";
+&pinctrl {
+	compatible = "st,stm32f469-pinctrl";
 
-			gpioa: gpio@40020000 {
-				gpio-ranges = <&pinctrl 0 0 16>;
-			};
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
 
-			gpiob: gpio@40020400 {
-				gpio-ranges = <&pinctrl 0 16 16>;
-			};
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
 
-			gpioc: gpio@40020800 {
-				gpio-ranges = <&pinctrl 0 32 16>;
-			};
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
 
-			gpiod: gpio@40020c00 {
-				gpio-ranges = <&pinctrl 0 48 16>;
-			};
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
 
-			gpioe: gpio@40021000 {
-				gpio-ranges = <&pinctrl 0 64 16>;
-			};
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
 
-			gpiof: gpio@40021400 {
-				gpio-ranges = <&pinctrl 0 80 16>;
-			};
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
 
-			gpiog: gpio@40021800 {
-				gpio-ranges = <&pinctrl 0 96 16>;
-			};
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
 
-			gpioh: gpio@40021c00 {
-				gpio-ranges = <&pinctrl 0 112 16>;
-			};
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
 
-			gpioi: gpio@40022000 {
-				gpio-ranges = <&pinctrl 0 128 16>;
-			};
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
 
-			gpioj: gpio@40022400 {
-				gpio-ranges = <&pinctrl 0 144 6>,
-					      <&pinctrl 12 156 4>;
-			};
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 6>,
+			      <&pinctrl 12 156 4>;
+	};
 
-			gpiok: gpio@40022800 {
-				gpio-ranges = <&pinctrl 3 163 5>;
-			};
-		};
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 3 163 5>;
 	};
 };
diff --git a/arch/arm/boot/dts/stm32f469.dtsi b/arch/arm/boot/dts/st/stm32f469.dtsi
index be002e8a78ac..be002e8a78ac 100644
--- a/arch/arm/boot/dts/stm32f469.dtsi
+++ b/arch/arm/boot/dts/st/stm32f469.dtsi
diff --git a/arch/arm/boot/dts/stm32f7-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f7-pinctrl.dtsi
index 9314128df185..97fc3fb5a9ca 100644
--- a/arch/arm/boot/dts/stm32f7-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32f7-pinctrl.dtsi
@@ -9,13 +9,12 @@
 
 / {
 	soc {
-		pinctrl: pin-controller {
+		pinctrl: pinctrl@40020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x40020000 0x3000>;
 			interrupt-parent = <&exti>;
 			st,syscfg = <&syscfg 0x8>;
-			pins-are-numbered;
 
 			gpioa: gpio@40020000 {
 				gpio-controller;
@@ -127,7 +126,7 @@
 				st,bank-name = "GPIOK";
 			};
 
-			cec_pins_a: cec@0 {
+			cec_pins_a: cec-0 {
 				pins {
 					pinmux = <STM32_PINMUX('A', 15, AF4)>; /* HDMI CEC */
 					slew-rate = <0>;
@@ -136,7 +135,7 @@
 				};
 			};
 
-			usart1_pins_a: usart1@0 {
+			usart1_pins_a: usart1-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */
 					bias-disable;
@@ -149,7 +148,7 @@
 				};
 			};
 
-			usart1_pins_b: usart1@1 {
+			usart1_pins_b: usart1-1 {
 				pins1 {
 					pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */
 					bias-disable;
@@ -162,7 +161,7 @@
 				};
 			};
 
-			i2c1_pins_b: i2c1@0 {
+			i2c1_pins_b: i2c1-0 {
 				pins {
 					pinmux = <STM32_PINMUX('B', 9, AF4)>, /* I2C1 SDA */
 						 <STM32_PINMUX('B', 8, AF4)>; /* I2C1 SCL */
@@ -172,7 +171,17 @@
 				};
 			};
 
-			usbotg_hs_pins_a: usbotg-hs@0 {
+			i2c3_pins_a: i2c3-0 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 8, AF4)>, /* I2C3_SDA */
+						 <STM32_PINMUX('H', 7, AF4)>; /* I2C3_SCL */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
+			usbotg_hs_pins_a: usbotg-hs-0 {
 				pins {
 					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT */
 						 <STM32_PINMUX('I', 11, AF10)>, /* OTG_HS_ULPI_DIR */
@@ -192,7 +201,7 @@
 				};
 			};
 
-			usbotg_hs_pins_b: usbotg-hs@1 {
+			usbotg_hs_pins_b: usbotg-hs-1 {
 				pins {
 					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT */
 						 <STM32_PINMUX('C', 2, AF10)>, /* OTG_HS_ULPI_DIR */
@@ -212,7 +221,7 @@
 				};
 			};
 
-			usbotg_fs_pins_a: usbotg-fs@0 {
+			usbotg_fs_pins_a: usbotg-fs-0 {
 				pins {
 					pinmux = <STM32_PINMUX('A', 10, AF10)>, /* OTG_FS_ID */
 						 <STM32_PINMUX('A', 11, AF10)>, /* OTG_FS_DM */
@@ -223,7 +232,7 @@
 				};
 			};
 
-			sdio_pins_a: sdio_pins_a@0 {
+			sdio_pins_a: sdio-pins-a-0 {
 				pins {
 					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1 D0 */
 						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1 D1 */
@@ -236,7 +245,7 @@
 				};
 			};
 
-			sdio_pins_od_a: sdio_pins_od_a@0 {
+			sdio_pins_od_a: sdio-pins-od-a-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1 D0 */
 						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1 D1 */
@@ -254,7 +263,18 @@
 				};
 			};
 
-			sdio_pins_b: sdio_pins_b@0 {
+			sdio_pins_sleep_a: sdio-pins-sleep-a-0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1 D0 */
+						 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1 D1 */
+						 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1 D2 */
+						 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1 D3 */
+						 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1 CLK */
+						 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1 CMD */
+				};
+			};
+
+			sdio_pins_b: sdio-pins-b-0 {
 				pins {
 					pinmux = <STM32_PINMUX('G', 9, AF11)>, /* SDMMC2 D0 */
 						 <STM32_PINMUX('G', 10, AF11)>, /* SDMMC2 D1 */
@@ -267,7 +287,7 @@
 				};
 			};
 
-			sdio_pins_od_b: sdio_pins_od_b@0 {
+			sdio_pins_od_b: sdio-pins-od-b-0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('G', 9, AF11)>, /* SDMMC2 D0 */
 						 <STM32_PINMUX('G', 10, AF11)>, /* SDMMC2 D1 */
@@ -284,6 +304,133 @@
 					slew-rate = <2>;
 				};
 			};
+
+			sdio_pins_sleep_b: sdio-pins-sleep-b-0 {
+				pins {
+					pinmux = <STM32_PINMUX('G', 9, ANALOG)>, /* SDMMC2 D0 */
+						 <STM32_PINMUX('G', 10, ANALOG)>, /* SDMMC2 D1 */
+						 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2 D2 */
+						 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2 D3 */
+						 <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC2 CLK */
+						 <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC2 CMD */
+				};
+			};
+
+			can1_pins_a: can1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 12, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 11, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can1_pins_b: can1-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 9, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 8, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can1_pins_c: can1-2 {
+				pins1 {
+					pinmux = <STM32_PINMUX('D', 1, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('D', 0, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+
+				};
+			};
+
+			can1_pins_d: can1-3 {
+				pins1 {
+					pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+
+				};
+			};
+
+			can2_pins_a: can2-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 6, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_b: can2-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 12, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can3_pins_a: can3-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 15, AF11)>; /* CAN3_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 8, AF11)>; /* CAN3_RX */
+					bias-pull-up;
+				};
+			};
+
+			can3_pins_b: can3-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 4, AF11)>;  /* CAN3_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 3, AF11)>; /* CAN3_RX */
+					bias-pull-up;
+				};
+			};
+
+			ltdc_pins_a: ltdc-0 {
+				pins {
+					pinmux = <STM32_PINMUX('E', 4, AF14)>, /* LCD_B0 */
+						 <STM32_PINMUX('G',12, AF9)>,  /* LCD_B4 */
+						 <STM32_PINMUX('I', 9, AF14)>, /* LCD_VSYNC */
+						 <STM32_PINMUX('I',10, AF14)>, /* LCD_HSYNC */
+						 <STM32_PINMUX('I',14, AF14)>, /* LCD_CLK */
+						 <STM32_PINMUX('I',15, AF14)>, /* LCD_R0 */
+						 <STM32_PINMUX('J', 0, AF14)>, /* LCD_R1 */
+						 <STM32_PINMUX('J', 1, AF14)>, /* LCD_R2 */
+						 <STM32_PINMUX('J', 2, AF14)>, /* LCD_R3 */
+						 <STM32_PINMUX('J', 3, AF14)>, /* LCD_R4 */
+						 <STM32_PINMUX('J', 4, AF14)>, /* LCD_R5 */
+						 <STM32_PINMUX('J', 5, AF14)>, /* LCD_R6 */
+						 <STM32_PINMUX('J', 6, AF14)>, /* LCD_R7 */
+						 <STM32_PINMUX('J', 7, AF14)>, /* LCD_G0 */
+						 <STM32_PINMUX('J', 8, AF14)>, /* LCD_G1 */
+						 <STM32_PINMUX('J', 9, AF14)>, /* LCD_G2 */
+						 <STM32_PINMUX('J',10, AF14)>, /* LCD_G3 */
+						 <STM32_PINMUX('J',11, AF14)>, /* LCD_G4 */
+						 <STM32_PINMUX('J',13, AF14)>, /* LCD_B1 */
+						 <STM32_PINMUX('J',14, AF14)>, /* LCD_B2 */
+						 <STM32_PINMUX('J',15, AF14)>, /* LCD_B3 */
+						 <STM32_PINMUX('K', 0, AF14)>, /* LCD_G5 */
+						 <STM32_PINMUX('K', 1, AF14)>, /* LCD_G6 */
+						 <STM32_PINMUX('K', 2, AF14)>, /* LCD_G7 */
+						 <STM32_PINMUX('K', 4, AF14)>, /* LCD_B5 */
+						 <STM32_PINMUX('K', 5, AF14)>, /* LCD_B6 */
+						 <STM32_PINMUX('K', 6, AF14)>, /* LCD_B7 */
+						 <STM32_PINMUX('K', 7, AF14)>; /* LCD_DE */
+					slew-rate = <2>;
+				};
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/stm32f746-disco.dts b/arch/arm/boot/dts/st/stm32f746-disco.dts
index 569d23cc61e5..087de6f09629 100644
--- a/arch/arm/boot/dts/stm32f746-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f746-disco.dts
@@ -43,8 +43,9 @@
 /dts-v1/;
 #include "stm32f746.dtsi"
 #include "stm32f746-pinctrl.dtsi"
-#include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "STMicroelectronics STM32F746-DISCO board";
@@ -60,6 +61,19 @@
 		reg = <0xC0000000 0x800000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			no-map;
+			size = <0x80000>;
+			linux,dma-default;
+		};
+	};
+
 	aliases {
 		serial0 = &usart1;
 	};
@@ -79,12 +93,31 @@
 		regulator-always-on;
 	};
 
-	mmc_vcard: mmc_vcard {
+	vcc_3v3: vcc-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "mmc_vcard";
+		regulator-name = "vcc_3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiok 3 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	panel_rgb: panel-rgb {
+		compatible = "rocktech,rk043fn48h";
+		power-supply = <&vcc_3v3>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpioi 12 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+		port {
+			panel_in_rgb: endpoint {
+				remote-endpoint = <&ltdc_out_rgb>;
+			};
+		};
+	};
 };
 
 &clk_hse {
@@ -99,16 +132,57 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins_a>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		interrupt-parent = <&gpioi>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <272>;
+	};
+};
+
+&ltdc {
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	port {
+		ltdc_out_rgb: endpoint {
+			remote-endpoint = <&panel_in_rgb>;
+		};
+	};
+};
+
 &sdio1 {
 	status = "okay";
-	vmmc-supply = <&mmc_vcard>;
+	vmmc-supply = <&vcc_3v3>;
 	cd-gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default", "opendrain";
+	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdio_pins_a>;
 	pinctrl-1 = <&sdio_pins_od_a>;
+	pinctrl-2 = <&sdio_pins_sleep_a>;
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_b>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi
new file mode 100644
index 000000000000..139f72b790c0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32f7-pinctrl.dtsi"
+
+&pinctrl {
+	compatible = "st,stm32f746-pinctrl";
+
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/st/stm32f746.dtsi
index d26f93f8b9c2..65c72b6fcc83 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/st/stm32f746.dtsi
@@ -40,7 +40,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../armv7-m.dtsi"
 #include <dt-bindings/clock/stm32fx-clock.h>
 #include <dt-bindings/mfd/stm32f7-rcc.h>
 
@@ -75,14 +75,6 @@
 	};
 
 	soc {
-		timer2: timer@40000000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000000 0x400>;
-			interrupts = <28>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM2)>;
-			status = "disabled";
-		};
-
 		timers2: timers@40000000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -105,14 +97,6 @@
 			};
 		};
 
-		timer3: timer@40000400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000400 0x400>;
-			interrupts = <29>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM3)>;
-			status = "disabled";
-		};
-
 		timers3: timers@40000400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -135,14 +119,6 @@
 			};
 		};
 
-		timer4: timer@40000800 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000800 0x400>;
-			interrupts = <30>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM4)>;
-			status = "disabled";
-		};
-
 		timers4: timers@40000800 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -165,13 +141,6 @@
 			};
 		};
 
-		timer5: timer@40000c00 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000c00 0x400>;
-			interrupts = <50>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM5)>;
-		};
-
 		timers5: timers@40000c00 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -194,14 +163,6 @@
 			};
 		};
 
-		timer6: timer@40001000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001000 0x400>;
-			interrupts = <54>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM6)>;
-			status = "disabled";
-		};
-
 		timers6: timers@40001000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -218,14 +179,6 @@
 			};
 		};
 
-		timer7: timer@40001400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001400 0x400>;
-			interrupts = <55>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM7)>;
-			status = "disabled";
-		};
-
 		timers7: timers@40001400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -265,8 +218,6 @@
 		};
 
 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM13)>;
@@ -281,8 +232,6 @@
 		};
 
 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM14)>;
@@ -300,16 +249,51 @@
 			compatible = "st,stm32-rtc";
 			reg = <0x40002800 0x400>;
 			clocks = <&rcc 1 CLK_RTC>;
-			clock-names = "ck_rtc";
 			assigned-clocks = <&rcc 1 CLK_RTC>;
 			assigned-clock-parents = <&rcc 1 CLK_LSE>;
 			interrupt-parent = <&exti>;
 			interrupts = <17 1>;
-			interrupt-names = "alarm";
 			st,syscfg = <&pwrcfg 0x00 0x100>;
 			status = "disabled";
 		};
 
+		can3: can@40003400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40003400 0x200>;
+			interrupts = <104>, <105>, <106>, <107>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F7_APB1_RESET(CAN3)>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN3)>;
+			st,gcan = <&gcan3>;
+			status = "disabled";
+		};
+
+		gcan3: gcan@40003600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40003600 0x200>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN3)>;
+		};
+
+		spi2: spi@40003800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f7-spi";
+			reg = <0x40003800 0x400>;
+			interrupts = <36>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(SPI2)>;
+			status = "disabled";
+		};
+
+		spi3: spi@40003c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f7-spi";
+			reg = <0x40003c00 0x400>;
+			interrupts = <51>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(SPI3)>;
+			status = "disabled";
+		};
+
 		usart2: serial@40004400 {
 			compatible = "st,stm32f7-uart";
 			reg = <0x40004400 0x400>;
@@ -366,9 +350,9 @@
 			status = "disabled";
 		};
 
-		i2c3: i2c@40005C00 {
+		i2c3: i2c@40005c00 {
 			compatible = "st,stm32f7-i2c";
-			reg = <0x40005C00 0x400>;
+			reg = <0x40005c00 0x400>;
 			interrupts = <72>,
 				     <73>;
 			resets = <&rcc STM32F7_APB1_RESET(I2C3)>;
@@ -390,6 +374,36 @@
 			status = "disabled";
 		};
 
+		can1: can@40006400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006400 0x200>;
+			interrupts = <19>, <20>, <21>, <22>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F7_APB1_RESET(CAN1)>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN1)>;
+			st,can-primary;
+			st,gcan = <&gcan1>;
+			status = "disabled";
+		};
+
+		gcan1: gcan@40006600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40006600 0x200>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN1)>;
+		};
+
+		can2: can@40006800 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006800 0x200>;
+			interrupts = <63>, <64>, <65>, <66>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F7_APB1_RESET(CAN2)>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN2)>;
+			st,can-secondary;
+			st,gcan = <&gcan1>;
+			status = "disabled";
+		};
+
 		cec: cec@40006c00 {
 			compatible = "st,stm32-cec";
 			reg = <0x40006C00 0x400>;
@@ -475,7 +489,7 @@
 			status = "disabled";
 		};
 
-		sdio2: sdio2@40011c00 {
+		sdio2: mmc@40011c00 {
 			compatible = "arm,pl180", "arm,primecell";
 			arm,primecell-periphid = <0x00880180>;
 			reg = <0x40011c00 0x400>;
@@ -486,7 +500,7 @@
 			status = "disabled";
 		};
 
-		sdio1: sdio1@40012c00 {
+		sdio1: mmc@40012c00 {
 			compatible = "arm,pl180", "arm,primecell";
 			arm,primecell-periphid = <0x00880180>;
 			reg = <0x40012c00 0x400>;
@@ -497,9 +511,30 @@
 			status = "disabled";
 		};
 
-		syscfg: system-config@40013800 {
-			compatible = "syscon";
+		spi1: spi@40013000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f7-spi";
+			reg = <0x40013000 0x400>;
+			interrupts = <35>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SPI1)>;
+			status = "disabled";
+		};
+
+		spi4: spi@40013400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f7-spi";
+			reg = <0x40013400 0x400>;
+			interrupts = <84>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SPI4)>;
+			status = "disabled";
+		};
+
+		syscfg: syscon@40013800 {
+			compatible = "st,stm32-syscfg", "syscon";
 			reg = <0x40013800 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SYSCFG)>;
 		};
 
 		exti: interrupt-controller@40013c00 {
@@ -533,8 +568,6 @@
 		};
 
 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM10)>;
@@ -549,8 +582,6 @@
 		};
 
 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM11)>;
@@ -564,15 +595,45 @@
 			};
 		};
 
+		spi5: spi@40015000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f7-spi";
+			reg = <0x40015000 0x400>;
+			interrupts = <85>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SPI5)>;
+			status = "disabled";
+		};
+
+		spi6: spi@40015400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f7-spi";
+			reg = <0x40015400 0x400>;
+			interrupts = <86>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SPI6)>;
+			status = "disabled";
+		};
+
+		ltdc: display-controller@40016800 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x40016800 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+			clocks = <&rcc 1 CLK_LCD>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
 		pwrcfg: power-config@40007000 {
-			compatible = "syscon";
+			compatible = "st,stm32-power-config", "syscon";
 			reg = <0x40007000 0x400>;
 		};
 
 		crc: crc@40023000 {
 			compatible = "st,stm32f7-crc";
 			reg = <0x40023000 0x400>;
-			clocks = <&rcc 0 12>;
+			clocks = <&rcc 0 STM32F7_AHB1_CLOCK(CRC)>;
 			status = "disabled";
 		};
 
@@ -587,7 +648,7 @@
 			assigned-clock-rates = <1000000>;
 		};
 
-		dma1: dma@40026000 {
+		dma1: dma-controller@40026000 {
 			compatible = "st,stm32-dma";
 			reg = <0x40026000 0x400>;
 			interrupts = <11>,
@@ -603,7 +664,7 @@
 			status = "disabled";
 		};
 
-		dma2: dma@40026400 {
+		dma2: dma-controller@40026400 {
 			compatible = "st,stm32-dma";
 			reg = <0x40026400 0x400>;
 			interrupts = <56>,
diff --git a/arch/arm/boot/dts/stm32f769-disco.dts b/arch/arm/boot/dts/st/stm32f769-disco.dts
index 1626e00bb2cb..5d12ae25b327 100644
--- a/arch/arm/boot/dts/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f769-disco.dts
@@ -66,21 +66,19 @@
 
 	leds {
 		compatible = "gpio-leds";
-		green {
+		led-green {
 			gpios = <&gpioj 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
-		red {
+		led-red {
 			gpios = <&gpioj 13 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
@@ -133,12 +131,25 @@
 	vmmc-supply = <&mmc_vcard>;
 	cd-gpios = <&gpioi 15 GPIO_ACTIVE_LOW>;
 	broken-cd;
-	pinctrl-names = "default", "opendrain";
+	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdio_pins_b>;
 	pinctrl-1 = <&sdio_pins_od_b>;
+	pinctrl-2 = <&sdio_pins_sleep_b>;
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi
new file mode 100644
index 000000000000..02c2a8b08468
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32f7-pinctrl.dtsi"
+
+&pinctrl {
+	compatible = "st,stm32f769-pinctrl";
+
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32h7-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32h7-pinctrl.dtsi
new file mode 100644
index 000000000000..7f1d234e1024
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h7-pinctrl.dtsi
@@ -0,0 +1,275 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
+				 <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	ethernet_rmii: rmii-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 11, AF11)>,
+				 <STM32_PINMUX('G', 13, AF11)>,
+				 <STM32_PINMUX('G', 12, AF11)>,
+				 <STM32_PINMUX('C', 4, AF11)>,
+				 <STM32_PINMUX('C', 5, AF11)>,
+				 <STM32_PINMUX('A', 7, AF11)>,
+				 <STM32_PINMUX('C', 1, AF11)>,
+				 <STM32_PINMUX('A', 2, AF11)>,
+				 <STM32_PINMUX('A', 1, AF11)>;
+			slew-rate = <2>;
+		};
+	};
+
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
+			bias-pull-up;
+		};
+	};
+
+	sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+				 <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
+		};
+	};
+
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 6, AF11)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 6, AF11)>; /* SDMMC1_CK */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	spi1_pins: spi1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 5, AF5)>,
+				/* SPI1_CLK */
+				 <STM32_PINMUX('B', 5, AF5)>;
+				/* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 9, AF5)>;
+				/* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
+	uart4_pins: uart4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 0, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 9, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	usart1_pins: usart1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_pins: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart3_pins: usart3-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS_DE */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usbotg_hs_pins_a: usbotg-hs-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 4, AF10)>,	/* ULPI_NXT */
+					 <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
+					 <STM32_PINMUX('C', 0, AF10)>,	/* ULPI_STP> */
+					 <STM32_PINMUX('A', 5, AF10)>,	/* ULPI_CK> */
+					 <STM32_PINMUX('A', 3, AF10)>,	/* ULPI_D0> */
+					 <STM32_PINMUX('B', 0, AF10)>,	/* ULPI_D1> */
+					 <STM32_PINMUX('B', 1, AF10)>,	/* ULPI_D2> */
+					 <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
+					 <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
+					 <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
+					 <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
+					 <STM32_PINMUX('B', 5, AF10)>;	/* ULPI_D7> */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+};
+
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/st/stm32h743.dtsi
index c065266ee377..b8d4c44c8a82 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/st/stm32h743.dtsi
@@ -40,7 +40,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../armv7-m.dtsi"
 #include <dt-bindings/clock/stm32h7-clks.h>
 #include <dt-bindings/mfd/stm32h7-rcc.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@@ -110,6 +110,7 @@
 			compatible = "st,stm32h7-spi";
 			reg = <0x40003800 0x400>;
 			interrupts = <36>;
+			resets = <&rcc STM32H7_APB1L_RESET(SPI2)>;
 			clocks = <&rcc SPI2_CK>;
 			status = "disabled";
 
@@ -121,18 +122,35 @@
 			compatible = "st,stm32h7-spi";
 			reg = <0x40003c00 0x400>;
 			interrupts = <51>;
+			resets = <&rcc STM32H7_APB1L_RESET(SPI3)>;
 			clocks = <&rcc SPI3_CK>;
 			status = "disabled";
 		};
 
 		usart2: serial@40004400 {
-			compatible = "st,stm32f7-uart";
+			compatible = "st,stm32h7-uart";
 			reg = <0x40004400 0x400>;
 			interrupts = <38>;
 			status = "disabled";
 			clocks = <&rcc USART2_CK>;
 		};
 
+		usart3: serial@40004800 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004800 0x400>;
+			interrupts = <39>;
+			status = "disabled";
+			clocks = <&rcc USART3_CK>;
+		};
+
+		uart4: serial@40004c00 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004c00 0x400>;
+			interrupts = <52>;
+			status = "disabled";
+			clocks = <&rcc UART4_CK>;
+		};
+
 		i2c1: i2c@40005400 {
 			compatible = "st,stm32f7-i2c";
 			#address-cells = <1>;
@@ -157,7 +175,7 @@
 			status = "disabled";
 		};
 
-		i2c3: i2c@40005C00 {
+		i2c3: i2c@40005c00 {
 			compatible = "st,stm32f7-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -180,21 +198,21 @@
 
 			dac1: dac@1 {
 				compatible = "st,stm32-dac";
-				#io-channels-cells = <1>;
+				#io-channel-cells = <1>;
 				reg = <1>;
 				status = "disabled";
 			};
 
 			dac2: dac@2 {
 				compatible = "st,stm32-dac";
-				#io-channels-cells = <1>;
+				#io-channel-cells = <1>;
 				reg = <2>;
 				status = "disabled";
 			};
 		};
 
 		usart1: serial@40011000 {
-			compatible = "st,stm32f7-uart";
+			compatible = "st,stm32h7-uart";
 			reg = <0x40011000 0x400>;
 			interrupts = <37>;
 			status = "disabled";
@@ -207,6 +225,7 @@
 			compatible = "st,stm32h7-spi";
 			reg = <0x40013000 0x400>;
 			interrupts = <35>;
+			resets = <&rcc STM32H7_APB2_RESET(SPI1)>;
 			clocks = <&rcc SPI1_CK>;
 			status = "disabled";
 		};
@@ -217,6 +236,7 @@
 			compatible = "st,stm32h7-spi";
 			reg = <0x40013400 0x400>;
 			interrupts = <84>;
+			resets = <&rcc STM32H7_APB2_RESET(SPI4)>;
 			clocks = <&rcc SPI4_CK>;
 			status = "disabled";
 		};
@@ -227,11 +247,12 @@
 			compatible = "st,stm32h7-spi";
 			reg = <0x40015000 0x400>;
 			interrupts = <85>;
+			resets = <&rcc STM32H7_APB2_RESET(SPI5)>;
 			clocks = <&rcc SPI5_CK>;
 			status = "disabled";
 		};
 
-		dma1: dma@40020000 {
+		dma1: dma-controller@40020000 {
 			compatible = "st,stm32-dma";
 			reg = <0x40020000 0x400>;
 			interrupts = <11>,
@@ -249,7 +270,7 @@
 			status = "disabled";
 		};
 
-		dma2: dma@40020400 {
+		dma2: dma-controller@40020400 {
 			compatible = "st,stm32-dma";
 			reg = <0x40020400 0x400>;
 			interrupts = <56>,
@@ -269,7 +290,7 @@
 
 		dmamux1: dma-router@40020800 {
 			compatible = "st,stm32h7-dmamux";
-			reg = <0x40020800 0x1c>;
+			reg = <0x40020800 0x40>;
 			#dma-cells = <3>;
 			dma-channels = <16>;
 			dma-requests = <128>;
@@ -329,7 +350,17 @@
 			status = "disabled";
 		};
 
-		mdma1: dma@52000000 {
+		ltdc: display-controller@50001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x50001000 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32H7_APB3_RESET(LTDC)>;
+			clocks = <&rcc LTDC_CK>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
+		mdma1: dma-controller@52000000 {
 			compatible = "st,stm32h7-mdma";
 			reg = <0x52000000 0x1000>;
 			interrupts = <122>;
@@ -339,12 +370,11 @@
 			dma-requests = <32>;
 		};
 
-		sdmmc1: sdmmc@52007000 {
+		sdmmc1: mmc@52007000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			arm,primecell-periphid = <0x10153180>;
 			reg = <0x52007000 0x1000>;
 			interrupts = <49>;
-			interrupt-names	= "cmd_irq";
 			clocks = <&rcc SDMMC1_CK>;
 			clock-names = "apb_pclk";
 			resets = <&rcc STM32H7_AHB3_RESET(SDMMC1)>;
@@ -353,6 +383,20 @@
 			max-frequency = <120000000>;
 		};
 
+		sdmmc2: mmc@48022400 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x10153180>;
+			reg = <0x48022400 0x400>;
+			interrupts = <124>;
+			clocks = <&rcc SDMMC2_CK>;
+			clock-names = "apb_pclk";
+			resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
 		exti: interrupt-controller@58000000 {
 			compatible = "st,stm32h7-exti";
 			interrupt-controller;
@@ -361,8 +405,8 @@
 			interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <62>, <76>;
 		};
 
-		syscfg: system-config@58000400 {
-			compatible = "syscon";
+		syscfg: syscon@58000400 {
+			compatible = "st,stm32-syscfg", "syscon";
 			reg = <0x58000400 0x400>;
 		};
 
@@ -372,11 +416,12 @@
 			compatible = "st,stm32h7-spi";
 			reg = <0x58001400 0x400>;
 			interrupts = <86>;
+			resets = <&rcc STM32H7_APB4_RESET(SPI6)>;
 			clocks = <&rcc SPI6_CK>;
 			status = "disabled";
 		};
 
-		i2c4: i2c@58001C00 {
+		i2c4: i2c@58001c00 {
 			compatible = "st,stm32f7-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -438,8 +483,6 @@
 		};
 
 		lptimer4: timer@58002c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58002c00 0x400>;
 			clocks = <&rcc LPTIM4_CK>;
@@ -454,8 +497,6 @@
 		};
 
 		lptimer5: timer@58003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58003000 0x400>;
 			clocks = <&rcc LPTIM5_CK>;
@@ -487,7 +528,6 @@
 			assigned-clock-parents = <&rcc LSE_CK>;
 			interrupt-parent = <&exti>;
 			interrupts = <17 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "alarm";
 			st,syscfg = <&pwrcfg 0x00 0x100>;
 			status = "disabled";
 		};
@@ -502,7 +542,7 @@
 		};
 
 		pwrcfg: power-config@58024800 {
-			compatible = "syscon";
+			compatible = "st,stm32-power-config", "syscon";
 			reg = <0x58024800 0x400>;
 		};
 
@@ -540,6 +580,147 @@
 			snps,pbl = <8>;
 			status = "disabled";
 		};
+
+		pinctrl: pinctrl@58020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32h743-pinctrl";
+			ranges = <0 0x58020000 0x3000>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&syscfg 0x8>;
+
+			gpioa: gpio@58020000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA_CK>;
+				st,bank-name = "GPIOA";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 0 16>;
+			};
+
+			gpiob: gpio@58020400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x400 0x400>;
+				clocks = <&rcc GPIOB_CK>;
+				st,bank-name = "GPIOB";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 16 16>;
+			};
+
+			gpioc: gpio@58020800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x800 0x400>;
+				clocks = <&rcc GPIOC_CK>;
+				st,bank-name = "GPIOC";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 32 16>;
+			};
+
+			gpiod: gpio@58020c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0xc00 0x400>;
+				clocks = <&rcc GPIOD_CK>;
+				st,bank-name = "GPIOD";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 48 16>;
+			};
+
+			gpioe: gpio@58021000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOE_CK>;
+				st,bank-name = "GPIOE";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 64 16>;
+			};
+
+			gpiof: gpio@58021400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1400 0x400>;
+				clocks = <&rcc GPIOF_CK>;
+				st,bank-name = "GPIOF";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 80 16>;
+			};
+
+			gpiog: gpio@58021800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1800 0x400>;
+				clocks = <&rcc GPIOG_CK>;
+				st,bank-name = "GPIOG";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 96 16>;
+			};
+
+			gpioh: gpio@58021c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1c00 0x400>;
+				clocks = <&rcc GPIOH_CK>;
+				st,bank-name = "GPIOH";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 112 16>;
+			};
+
+			gpioi: gpio@58022000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOI_CK>;
+				st,bank-name = "GPIOI";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 128 16>;
+			};
+
+			gpioj: gpio@58022400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2400 0x400>;
+				clocks = <&rcc GPIOJ_CK>;
+				st,bank-name = "GPIOJ";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 144 16>;
+			};
+
+			gpiok: gpio@58022800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2800 0x400>;
+				clocks = <&rcc GPIOK_CK>;
+				st,bank-name = "GPIOK";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl 0 160 8>;
+			};
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/stm32h743i-disco.dts b/arch/arm/boot/dts/st/stm32h743i-disco.dts
index e446d311c520..2b452883a708 100644
--- a/arch/arm/boot/dts/stm32h743i-disco.dts
+++ b/arch/arm/boot/dts/st/stm32h743i-disco.dts
@@ -42,7 +42,7 @@
 
 /dts-v1/;
 #include "stm32h743.dtsi"
-#include "stm32h743-pinctrl.dtsi"
+#include "stm32h7-pinctrl.dtsi"
 
 / {
 	model = "STMicroelectronics STM32H743i-Discovery board";
@@ -77,10 +77,10 @@
 
 &mac {
 	status = "disabled";
-	pinctrl-0	= <&ethernet_rmii>;
-	pinctrl-names	= "default";
-	phy-mode	= "rmii";
-	phy-handle	= <&phy0>;
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
 
 	mdio0 {
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/stm32h743i-eval.dts b/arch/arm/boot/dts/st/stm32h743i-eval.dts
index 8f398178f5e5..5c5d8059bdc7 100644
--- a/arch/arm/boot/dts/stm32h743i-eval.dts
+++ b/arch/arm/boot/dts/st/stm32h743i-eval.dts
@@ -42,7 +42,7 @@
 
 /dts-v1/;
 #include "stm32h743.dtsi"
-#include "stm32h743-pinctrl.dtsi"
+#include "stm32h7-pinctrl.dtsi"
 
 / {
 	model = "STMicroelectronics STM32H743i-EVAL board";
@@ -115,10 +115,10 @@
 
 &mac {
 	status = "disabled";
-	pinctrl-0	= <&ethernet_rmii>;
-	pinctrl-names	= "default";
-	phy-mode	= "rmii";
-	phy-handle	= <&phy0>;
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
 
 	mdio0 {
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/st/stm32h750.dtsi b/arch/arm/boot/dts/st/stm32h750.dtsi
new file mode 100644
index 000000000000..41e3b1e3a874
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h750.dtsi
@@ -0,0 +1,6 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
+
+#include "stm32h743.dtsi"
+
+
diff --git a/arch/arm/boot/dts/st/stm32h750i-art-pi.dts b/arch/arm/boot/dts/st/stm32h750i-art-pi.dts
new file mode 100644
index 000000000000..44c307f8b09c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h750i-art-pi.dts
@@ -0,0 +1,229 @@
+/*
+ * Copyright 2021 - Dillon Min <dillon.minfei@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * For art-pi board resources, you can refer to link:
+ * 	https://art-pi.gitee.io/website/
+ */
+
+/dts-v1/;
+#include "stm32h750.dtsi"
+#include "stm32h7-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "RT-Thread STM32H750i-ART-PI board";
+	compatible = "st,stm32h750i-art-pi", "st,stm32h750";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:2000000n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x2000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			no-map;
+			size = <0x100000>;
+			linux,dma-default;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-red {
+			gpios = <&gpioi 8 0>;
+		};
+		led-green {
+			gpios = <&gpioc 15 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&dma1 {
+	status = "okay";
+};
+
+&dma2 {
+	status = "okay";
+};
+
+&mac {
+	status = "disabled";
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
+	dmas = <&dmamux1 37 0x400 0x05>,
+	       <&dmamux1 38 0x400 0x05>;
+	dma-names = "rx", "tx";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+
+		partition@0 {
+			label = "root filesystem";
+			reg = <0 0x1000000>;
+		};
+	};
+};
+
+&usart2 {
+	pinctrl-0 = <&usart2_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins>;
+	dmas = <&dmamux1 45 0x400 0x05>,
+	       <&dmamux1 46 0x400 0x05>;
+	dma-names = "rx", "tx";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+		max-speed = <115200>;
+	};
+};
+
+&uart4 {
+	pinctrl-0 = <&uart4_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+
diff --git a/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
new file mode 100644
index 000000000000..27e0c3826789
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com>
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+	adc1_usb_cc_pins_a: adc1-usb-cc-pins-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+				 <STM32_PINMUX('A', 3, ANALOG)>; /* ADC1 in12 */
+		};
+	};
+
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('E', 8, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c1_sleep_pins_a: i2c1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('E', 8, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	i2c5_pins_a: i2c5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('H', 6, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c5_sleep_pins_a: i2c5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('H', 6, ANALOG)>; /* I2C5_SDA */
+		};
+	};
+
+	mcp23017_pins_a: mcp23017-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 12, GPIO)>;
+			bias-pull-up;
+		};
+	};
+
+	pwm3_pins_a: pwm3-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 1, AF2)>; /* TIM3_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm3_sleep_pins_a: pwm3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 1, ANALOG)>; /* TIM3_CH4 */
+		};
+	};
+
+	pwm4_pins_a: pwm4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, AF2)>; /* TIM4_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm4_sleep_pins_a: pwm4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, ANALOG)>; /* TIM4_CH2 */
+		};
+	};
+
+	pwm8_pins_a: pwm8-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 5, AF3)>; /* TIM8_CH3 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm8_sleep_pins_a: pwm8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 5, ANALOG)>; /* TIM8_CH3 */
+		};
+	};
+
+	pwm14_pins_a: pwm14-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 9, AF9)>; /* TIM14_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm14_sleep_pins_a: pwm14-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 9, ANALOG)>; /* TIM14_CH1 */
+		};
+	};
+
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_clk_pins_a: sdmmc1-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, AF10)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF10)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF10)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF10)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+				 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+		};
+	};
+
+	sdmmc2_clk_pins_a: sdmmc2-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 3, AF10)>; /* SDMMC2_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	spi5_pins_a: spi5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 7, AF6)>, /* SPI5_SCK */
+				 <STM32_PINMUX('H', 3, AF5)>; /* SPI5_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF5)>; /* SPI5_MISO */
+			bias-disable;
+		};
+	};
+
+	spi5_sleep_pins_a: spi5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 7, ANALOG)>, /* SPI5_SCK */
+				 <STM32_PINMUX('A', 8, ANALOG)>, /* SPI5_MISO */
+				 <STM32_PINMUX('H', 3, ANALOG)>; /* SPI5_MOSI */
+		};
+	};
+
+	stm32g0_intn_pins_a: stm32g0-intn-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 2, GPIO)>;
+			bias-pull-up;
+		};
+	};
+
+	uart4_pins_a: uart4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 6, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_idle_pins_a: uart4-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 6, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_sleep_pins_a: uart4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 6, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('D', 8, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	uart8_pins_a: uart8-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 9, AF8)>; /* UART8_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart8_idle_pins_a: uart8-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, ANALOG)>; /* UART8_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 9, AF8)>; /* UART8_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart8_sleep_pins_a: uart8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 1, ANALOG)>, /* UART8_TX */
+				 <STM32_PINMUX('F', 9, ANALOG)>; /* UART8_RX */
+		};
+	};
+
+	usart1_pins_a: usart1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 0, AF7)>, /* USART1_TX */
+				 <STM32_PINMUX('C', 2, AF7)>; /* USART1_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 0, AF4)>, /* USART1_RX */
+				 <STM32_PINMUX('A', 7, AF7)>; /* USART1_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart1_idle_pins_a: usart1-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* USART1_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 2, AF7)>; /* USART1_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 0, AF4)>; /* USART1_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart1_sleep_pins_a: usart1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* USART1_RTS */
+				 <STM32_PINMUX('A', 7, ANALOG)>, /* USART1_CTS_NSS */
+				 <STM32_PINMUX('B', 0, ANALOG)>; /* USART1_RX */
+		};
+	};
+
+	usart2_pins_a: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 12, AF1)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, AF3)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 15, AF1)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 11, AF2)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart2_idle_pins_a: usart2-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 12, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 4, AF3)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 15, AF1)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_sleep_pins_a: usart2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 12, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('D', 15, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi
new file mode 100644
index 000000000000..b04d24c939c3
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp131.dtsi
@@ -0,0 +1,1517 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/stm32mp13-clks.h>
+#include <dt-bindings/reset/stm32mp13-resets.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+		interrupt-parent = <&intc>;
+	};
+
+	firmware {
+		optee {
+			method = "smc";
+			compatible = "linaro,optee-tz";
+			interrupt-parent = <&intc>;
+			interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		};
+
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+
+			scmi_voltd: protocol@17 {
+				reg = <0x17>;
+
+				scmi_regu: regulators {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					scmi_reg11: regulator@0 {
+						reg = <VOLTD_SCMI_REG11>;
+						regulator-name = "reg11";
+					};
+					scmi_reg18: regulator@1 {
+						reg = <VOLTD_SCMI_REG18>;
+						regulator-name = "reg18";
+					};
+					scmi_usb33: regulator@2 {
+						reg = <VOLTD_SCMI_USB33>;
+						regulator-name = "usb33";
+					};
+				};
+			};
+		};
+	};
+
+	intc: interrupt-controller@a0021000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0xa0021000 0x1000>,
+		      <0xa0022000 0x2000>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&intc>;
+		always-on;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+
+		timers2: timer@40000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000000 0x400>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM2_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 18 0x400 0x1>,
+			       <&dmamux1 19 0x400 0x1>,
+			       <&dmamux1 20 0x400 0x1>,
+			       <&dmamux1 21 0x400 0x1>,
+			       <&dmamux1 22 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@1 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers3: timer@40001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001000 0x400>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM3_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 23 0x400 0x1>,
+			       <&dmamux1 24 0x400 0x1>,
+			       <&dmamux1 25 0x400 0x1>,
+			       <&dmamux1 26 0x400 0x1>,
+			       <&dmamux1 27 0x400 0x1>,
+			       <&dmamux1 28 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@2 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers4: timer@40002000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40002000 0x400>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM4_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 29 0x400 0x1>,
+			       <&dmamux1 30 0x400 0x1>,
+			       <&dmamux1 31 0x400 0x1>,
+			       <&dmamux1 32 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@3 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <3>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers5: timer@40003000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40003000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM5_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 55 0x400 0x1>,
+			       <&dmamux1 56 0x400 0x1>,
+			       <&dmamux1 57 0x400 0x1>,
+			       <&dmamux1 58 0x400 0x1>,
+			       <&dmamux1 59 0x400 0x1>,
+			       <&dmamux1 60 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@4 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <4>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers6: timer@40004000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40004000 0x400>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM6_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 69 0x400 0x1>;
+			dma-names = "up";
+			status = "disabled";
+
+			timer@5 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		timers7: timer@40005000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40005000 0x400>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM7_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 70 0x400 0x1>;
+			dma-names = "up";
+			status = "disabled";
+
+			timer@6 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <6>;
+				status = "disabled";
+			};
+		};
+
+		lptimer1: timer@40009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x40009000 0x400>;
+			interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM1_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@0 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		i2s2: audio-controller@4000b000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x4000b000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi2: spi@4000b000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000b000 0x400>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI2_K>;
+			resets = <&rcc SPI2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s3: audio-controller@4000c000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x4000c000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi3: spi@4000c000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000c000 0x400>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI3_K>;
+			resets = <&rcc SPI3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spdifrx: audio-controller@4000d000 {
+			compatible = "st,stm32h7-spdifrx";
+			reg = <0x4000d000 0x400>;
+			#sound-dai-cells = <0>;
+			clocks = <&rcc SPDIF_K>;
+			clock-names = "kclk";
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 93 0x400 0x01>,
+			       <&dmamux1 94 0x400 0x01>;
+			dma-names = "rx", "rx-ctrl";
+			status = "disabled";
+		};
+
+		usart3: serial@4000f000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4000f000 0x400>;
+			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART3_K>;
+			resets = <&rcc USART3_R>;
+			wakeup-source;
+			dmas = <&dmamux1 45 0x400 0x5>,
+			       <&dmamux1 46 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart4: serial@40010000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40010000 0x400>;
+			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART4_K>;
+			resets = <&rcc UART4_R>;
+			wakeup-source;
+			dmas = <&dmamux1 63 0x400 0x5>,
+			       <&dmamux1 64 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart5: serial@40011000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40011000 0x400>;
+			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART5_K>;
+			resets = <&rcc UART5_R>;
+			wakeup-source;
+			dmas = <&dmamux1 65 0x400 0x5>,
+			       <&dmamux1 66 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c1: i2c@40012000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x40012000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C1_K>;
+			resets = <&rcc I2C1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 33 0x400 0x1>,
+			       <&dmamux1 34 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x1>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c2: i2c@40013000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x40013000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C2_K>;
+			resets = <&rcc I2C2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 35 0x400 0x1>,
+			       <&dmamux1 36 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x2>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		uart7: serial@40018000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40018000 0x400>;
+			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART7_K>;
+			resets = <&rcc UART7_R>;
+			wakeup-source;
+			dmas = <&dmamux1 79 0x400 0x5>,
+			       <&dmamux1 80 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart8: serial@40019000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40019000 0x400>;
+			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART8_K>;
+			resets = <&rcc UART8_R>;
+			wakeup-source;
+			dmas = <&dmamux1 81 0x400 0x5>,
+			       <&dmamux1 82 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		timers1: timer@44000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44000000 0x400>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
+			clocks = <&rcc TIM1_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 11 0x400 0x1>,
+			       <&dmamux1 12 0x400 0x1>,
+			       <&dmamux1 13 0x400 0x1>,
+			       <&dmamux1 14 0x400 0x1>,
+			       <&dmamux1 15 0x400 0x1>,
+			       <&dmamux1 16 0x400 0x1>,
+			       <&dmamux1 17 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4",
+				    "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@0 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers8: timer@44001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44001000 0x400>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
+			clocks = <&rcc TIM8_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 47 0x400 0x1>,
+			       <&dmamux1 48 0x400 0x1>,
+			       <&dmamux1 49 0x400 0x1>,
+			       <&dmamux1 50 0x400 0x1>,
+			       <&dmamux1 51 0x400 0x1>,
+			       <&dmamux1 52 0x400 0x1>,
+			       <&dmamux1 53 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4",
+				    "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@7 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <7>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		usart6: serial@44003000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x44003000 0x400>;
+			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART6_K>;
+			resets = <&rcc USART6_R>;
+			wakeup-source;
+			dmas = <&dmamux1 71 0x400 0x5>,
+			       <&dmamux1 72 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s1: audio-controller@44004000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x44004000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi1: spi@44004000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x44004000 0x400>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI1_K>;
+			resets = <&rcc SPI1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		sai1: sai@4400a000 {
+			compatible = "st,stm32h7-sai";
+			reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
+			ranges = <0 0x4400a000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI1_R>;
+			status = "disabled";
+
+			sai1a: audio-controller@4400a004 {
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x4 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI1_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 87 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai1b: audio-controller@4400a024 {
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI1_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 88 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		sai2: sai@4400b000 {
+			compatible = "st,stm32h7-sai";
+			reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
+			ranges = <0 0x4400b000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI2_R>;
+			status = "disabled";
+
+			sai2a: audio-controller@4400b004 {
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x4 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI2_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 89 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai2b: audio-controller@4400b024 {
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI2_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 90 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		dfsdm: dfsdm@4400d000 {
+			compatible = "st,stm32mp1-dfsdm";
+			reg = <0x4400d000 0x800>;
+			clocks = <&rcc DFSDM_K>;
+			clock-names = "dfsdm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dfsdm0: filter@0 {
+				compatible = "st,stm32-dfsdm-adc";
+				reg = <0>;
+				#io-channel-cells = <1>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 101 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm1: filter@1 {
+				compatible = "st,stm32-dfsdm-adc";
+				reg = <1>;
+				#io-channel-cells = <1>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 102 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+		};
+
+		dma1: dma-controller@48000000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48000000 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA1>;
+			resets = <&rcc DMA1_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dma2: dma-controller@48001000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48001000 0x400>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA2>;
+			resets = <&rcc DMA2_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dmamux1: dma-router@48002000 {
+			compatible = "st,stm32h7-dmamux";
+			reg = <0x48002000 0x40>;
+			clocks = <&rcc DMAMUX1>;
+			resets = <&rcc DMAMUX1_R>;
+			#dma-cells = <3>;
+			dma-masters = <&dma1 &dma2>;
+			dma-requests = <128>;
+			dma-channels = <16>;
+		};
+
+		adc_2: adc@48004000 {
+			compatible = "st,stm32mp13-adc-core";
+			reg = <0x48004000 0x400>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc ADC2>, <&rcc ADC2_K>;
+			clock-names = "bus", "adc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc2: adc@0 {
+				compatible = "st,stm32mp13-adc";
+				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>;
+				interrupt-parent = <&adc_2>;
+				interrupts = <0>;
+				dmas = <&dmamux1 10 0x400 0x80000001>;
+				dma-names = "rx";
+				status = "disabled";
+
+				channel@13 {
+					reg = <13>;
+					label = "vrefint";
+				};
+				channel@14 {
+					reg = <14>;
+					label = "vddcore";
+				};
+				channel@16 {
+					reg = <16>;
+					label = "vddcpu";
+				};
+				channel@17 {
+					reg = <17>;
+					label = "vddq_ddr";
+				};
+			};
+		};
+
+		usbotg_hs: usb@49000000 {
+			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
+			reg = <0x49000000 0x40000>;
+			clocks = <&rcc USBO_K>;
+			clock-names = "otg";
+			resets = <&rcc USBO_R>;
+			reset-names = "dwc2";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			g-rx-fifo-size = <512>;
+			g-np-tx-fifo-size = <32>;
+			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
+			dr_mode = "otg";
+			otg-rev = <0x200>;
+			usb33d-supply = <&scmi_usb33>;
+			status = "disabled";
+		};
+
+		usart1: serial@4c000000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4c000000 0x400>;
+			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART1_K>;
+			resets = <&rcc USART1_R>;
+			wakeup-source;
+			dmas = <&dmamux1 41 0x400 0x5>,
+			       <&dmamux1 42 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		usart2: serial@4c001000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4c001000 0x400>;
+			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART2_K>;
+			resets = <&rcc USART2_R>;
+			wakeup-source;
+			dmas = <&dmamux1 43 0x400 0x5>,
+			       <&dmamux1 44 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s4: audio-controller@4c002000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x4c002000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 83 0x400 0x01>,
+			       <&dmamux1 84 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi4: spi@4c002000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c002000 0x400>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI4_K>;
+			resets = <&rcc SPI4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 83 0x400 0x01>,
+			       <&dmamux1 84 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi5: spi@4c003000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c003000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI5_K>;
+			resets = <&rcc SPI5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 85 0x400 0x01>,
+			       <&dmamux1 86 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c3: i2c@4c004000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c004000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C3_K>;
+			resets = <&rcc I2C3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 73 0x400 0x1>,
+			       <&dmamux1 74 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x4>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c4: i2c@4c005000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c005000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C4_K>;
+			resets = <&rcc I2C4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 75 0x400 0x1>,
+			       <&dmamux1 76 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x8>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c5: i2c@4c006000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c006000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C5_K>;
+			resets = <&rcc I2C5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 115 0x400 0x1>,
+			       <&dmamux1 116 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x10>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		timers12: timer@4c007000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c007000 0x400>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM12_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@11 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <11>;
+				status = "disabled";
+			};
+		};
+
+		timers13: timer@4c008000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c008000 0x400>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM13_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@12 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <12>;
+				status = "disabled";
+			};
+		};
+
+		timers14: timer@4c009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c009000 0x400>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM14_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@13 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <13>;
+				status = "disabled";
+			};
+		};
+
+		timers15: timer@4c00a000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c00a000 0x400>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM15_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 105 0x400 0x1>,
+			       <&dmamux1 106 0x400 0x1>,
+			       <&dmamux1 107 0x400 0x1>,
+			       <&dmamux1 108 0x400 0x1>;
+			dma-names = "ch1", "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@14 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <14>;
+				status = "disabled";
+			};
+		};
+
+		timers16: timer@4c00b000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c00b000 0x400>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM16_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 109 0x400 0x1>,
+			       <&dmamux1 110 0x400 0x1>;
+			dma-names = "ch1", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@15 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <15>;
+				status = "disabled";
+			};
+		};
+
+		timers17: timer@4c00c000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c00c000 0x400>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM17_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 111 0x400 0x1>,
+			       <&dmamux1 112 0x400 0x1>;
+			dma-names = "ch1", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@16 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <16>;
+				status = "disabled";
+			};
+		};
+
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp13-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clock-names = "hse", "hsi", "csi", "lse", "lsi";
+			clocks = <&scmi_clk CK_SCMI_HSE>,
+				 <&scmi_clk CK_SCMI_HSI>,
+				 <&scmi_clk CK_SCMI_CSI>,
+				 <&scmi_clk CK_SCMI_LSE>,
+				 <&scmi_clk CK_SCMI_LSI>;
+		};
+
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp13-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
+
+		syscfg: syscon@50020000 {
+			compatible = "st,stm32mp157-syscfg", "syscon";
+			reg = <0x50020000 0x400>;
+			clocks = <&rcc SYSCFG>;
+		};
+
+		lptimer2: timer@50021000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50021000 0x400>;
+			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM2_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@1 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		lptimer3: timer@50022000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50022000 0x400>;
+			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM3_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@2 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		lptimer4: timer@50023000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50023000 0x400>;
+			interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM4_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		lptimer5: timer@50024000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50024000 0x400>;
+			interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM5_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		hash: hash@54003000 {
+			compatible = "st,stm32mp13-hash";
+			reg = <0x54003000 0x400>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc HASH1>;
+			resets = <&rcc HASH1_R>;
+			dmas = <&mdma 30 0x2 0x1000a02 0x0 0x0>;
+			dma-names = "in";
+			status = "disabled";
+		};
+
+		rng: rng@54004000 {
+			compatible = "st,stm32mp13-rng";
+			reg = <0x54004000 0x400>;
+			clocks = <&rcc RNG1_K>;
+			resets = <&rcc RNG1_R>;
+			status = "disabled";
+		};
+
+		mdma: dma-controller@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
+		};
+
+		fmc: memory-controller@58002000 {
+			compatible = "st,stm32mp1-fmc2-ebi";
+			reg = <0x58002000 0x1000>;
+			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+				 <4 0 0x80000000 0x10000000>; /* NAND */
+			#address-cells = <2>;
+			#size-cells = <1>;
+			clocks = <&rcc FMC_K>;
+			resets = <&rcc FMC_R>;
+			status = "disabled";
+
+			nand-controller@4,0 {
+				compatible = "st,stm32mp1-fmc2-nfc";
+				reg = <4 0x00000000 0x1000>,
+				      <4 0x08010000 0x1000>,
+				      <4 0x08020000 0x1000>,
+				      <4 0x01000000 0x1000>,
+				      <4 0x09010000 0x1000>,
+				      <4 0x09020000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>,
+				       <&mdma 24 0x2 0x12000a08 0x0 0x0>,
+				       <&mdma 25 0x2 0x12000a0a 0x0 0x0>;
+				dma-names = "tx", "rx", "ecc";
+				status = "disabled";
+			};
+		};
+
+		qspi: spi@58003000 {
+			compatible = "st,stm32f469-qspi";
+			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+			reg-names = "qspi", "qspi_mm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>,
+			       <&mdma 26 0x2 0x10100008 0x0 0x0>;
+			dma-names = "tx", "rx";
+			clocks = <&rcc QSPI_K>;
+			resets = <&rcc QSPI_R>;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@58005000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x20253180>;
+			reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC1_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC1_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <130000000>;
+			status = "disabled";
+		};
+
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x20253180>;
+			reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <130000000>;
+			status = "disabled";
+		};
+
+		usbh_ohci: usb@5800c000 {
+			compatible = "generic-ohci";
+			reg = <0x5800c000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		usbh_ehci: usb@5800d000 {
+			compatible = "generic-ehci";
+			reg = <0x5800d000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			companion = <&usbh_ohci>;
+			status = "disabled";
+		};
+
+		iwdg2: watchdog@5a002000 {
+			compatible = "st,stm32mp1-iwdg";
+			reg = <0x5a002000 0x400>;
+			clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+			clock-names = "pclk", "lsi";
+			status = "disabled";
+		};
+
+		usbphyc: usbphyc@5a006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <0>;
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc USBPHY_K>;
+			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&scmi_reg11>;
+			vdda1v8-supply = <&scmi_reg18>;
+			status = "disabled";
+
+			usbphyc_port0: usb-phy@0 {
+				#phy-cells = <0>;
+				reg = <0>;
+			};
+
+			usbphyc_port1: usb-phy@1 {
+				#phy-cells = <1>;
+				reg = <1>;
+			};
+		};
+
+		rtc: rtc@5c004000 {
+			compatible = "st,stm32mp1-rtc";
+			reg = <0x5c004000 0x400>;
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scmi_clk CK_SCMI_RTCAPB>,
+				 <&scmi_clk CK_SCMI_RTC>;
+			clock-names = "pclk", "rtc_ck";
+			status = "disabled";
+		};
+
+		bsec: efuse@5c005000 {
+			compatible = "st,stm32mp13-bsec";
+			reg = <0x5c005000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			part_number_otp: part_number_otp@4 {
+				reg = <0x4 0x2>;
+				bits = <0 12>;
+			};
+			ts_cal1: calib@5c {
+				reg = <0x5c 0x2>;
+			};
+			ts_cal2: calib@5e {
+				reg = <0x5e 0x2>;
+			};
+		};
+
+		/*
+		 * Break node order to solve dependency probe issue between
+		 * pinctrl and exti.
+		 */
+		pinctrl: pinctrl@50002000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp135-pinctrl";
+			ranges = <0 0x50002000 0x8400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioa: gpio@50002000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA>;
+				st,bank-name = "GPIOA";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 0 16>;
+			};
+
+			gpiob: gpio@50003000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOB>;
+				st,bank-name = "GPIOB";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 16 16>;
+			};
+
+			gpioc: gpio@50004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOC>;
+				st,bank-name = "GPIOC";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 32 16>;
+			};
+
+			gpiod: gpio@50005000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x400>;
+				clocks = <&rcc GPIOD>;
+				st,bank-name = "GPIOD";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 48 16>;
+			};
+
+			gpioe: gpio@50006000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x400>;
+				clocks = <&rcc GPIOE>;
+				st,bank-name = "GPIOE";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 64 16>;
+			};
+
+			gpiof: gpio@50007000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x400>;
+				clocks = <&rcc GPIOF>;
+				st,bank-name = "GPIOF";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 80 16>;
+			};
+
+			gpiog: gpio@50008000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x400>;
+				clocks = <&rcc GPIOG>;
+				st,bank-name = "GPIOG";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 96 16>;
+			};
+
+			gpioh: gpio@50009000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x400>;
+				clocks = <&rcc GPIOH>;
+				st,bank-name = "GPIOH";
+				ngpios = <15>;
+				gpio-ranges = <&pinctrl 0 112 15>;
+			};
+
+			gpioi: gpio@5000a000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x400>;
+				clocks = <&rcc GPIOI>;
+				st,bank-name = "GPIOI";
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl 0 128 8>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp133.dtsi b/arch/arm/boot/dts/st/stm32mp133.dtsi
new file mode 100644
index 000000000000..df451c3c2a26
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp133.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp131.dtsi"
+
+/ {
+	soc {
+		m_can1: can@4400e000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+
+		m_can2: can@4400f000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+
+		adc_1: adc@48003000 {
+			compatible = "st,stm32mp13-adc-core";
+			reg = <0x48003000 0x400>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc ADC1>, <&rcc ADC1_K>;
+			clock-names = "bus", "adc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc1: adc@0 {
+				compatible = "st,stm32mp13-adc";
+				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>;
+				interrupt-parent = <&adc_1>;
+				interrupts = <0>;
+				dmas = <&dmamux1 9 0x400 0x80000001>;
+				dma-names = "rx";
+				status = "disabled";
+
+				channel@18 {
+					reg = <18>;
+					label = "vrefint";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp135.dtsi b/arch/arm/boot/dts/st/stm32mp135.dtsi
new file mode 100644
index 000000000000..68d32f9f5314
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp135.dtsi
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp133.dtsi"
+
+/ {
+	soc {
+		dcmipp: dcmipp@5a000000 {
+			compatible = "st,stm32mp13-dcmipp";
+			reg = <0x5a000000 0x400>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc DCMIPP_R>;
+			clocks = <&rcc DCMIPP_K>;
+			status = "disabled";
+
+			port {
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
new file mode 100644
index 000000000000..eea740d097c7
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
+#include "stm32mp135.dtsi"
+#include "stm32mp13xf.dtsi"
+#include "stm32mp13-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP135F-DK Discovery Board";
+	compatible = "st,stm32mp135f-dk", "st,stm32mp135";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart1;
+		serial2 = &uart8;
+		serial3 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		optee@dd000000 {
+			reg = <0xdd000000 0x3000000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-user {
+			label = "User-PA13";
+			linux,code = <BTN_1>;
+			gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+};
+
+&adc_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc1_usb_cc_pins_a>;
+	vdda-supply = <&scmi_vdd_adc>;
+	vref-supply = <&scmi_vdd_adc>;
+	status = "okay";
+	adc1: adc@0 {
+		status = "okay";
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in6 & in12.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (5.1 + 47kOhms) * 5pF => 1.3us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@12 {
+			reg = <12>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <96>;
+	i2c-scl-falling-time-ns = <3>;
+	clock-frequency = <1000000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	mcp23017: pinctrl@21 {
+		compatible = "microchip,mcp23017";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpiog>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcp23017_pins_a>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		microchip,irq-mirror;
+	};
+
+	typec@53 {
+		compatible = "st,stm32g0-typec";
+		reg = <0x53>;
+		/* Alert pin on PI2 */
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		/* Internal pull-up on PI2 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&stm32g0_intn_pins_a>;
+		firmware-name = "stm32g0-ucsi.mp135f-dk.fw";
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+
+			port {
+				con_usb_c_g0_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <170>;
+	i2c-scl-falling-time-ns = <5>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&scmi_regu {
+	scmi_vdd_adc: regulator@10 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO1>;
+		regulator-name = "vdd_adc";
+	};
+	scmi_vdd_usb: regulator@13 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO4>;
+		regulator-name = "vdd_usb";
+	};
+	scmi_vdd_sd: regulator@14 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO5>;
+		regulator-name = "vdd_sd";
+	};
+	scmi_v1v8_periph: regulator@15 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO6>;
+		regulator-name = "v1v8_periph";
+	};
+	scmi_v3v3_sw: regulator@19 {
+		reg = <VOLTD_SCMI_STPMIC1_PWR_SW2>;
+		regulator-name = "v3v3_sw";
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioh 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&scmi_vdd_sd>;
+	status = "okay";
+};
+
+&spi5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi5_pins_a>;
+	pinctrl-1 = <&spi5_sleep_pins_a>;
+	status = "disabled";
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a>;
+		pinctrl-1 = <&pwm4_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-1 = <&pwm8_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@7 {
+		status = "okay";
+	};
+};
+
+&timers14 {
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm14_pins_a>;
+		pinctrl-1 = <&pwm14_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@13 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart8_pins_a>;
+	pinctrl-1 = <&uart8_sleep_pins_a>;
+	pinctrl-2 = <&uart8_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&usart1 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-1 = <&usart1_sleep_pins_a>;
+	pinctrl-2 = <&usart1_idle_pins_a>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+/* Bluetooth */
+&usart2 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	pinctrl-2 = <&usart2_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&scmi_v3v3_sw>;
+	};
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usb_c_g0_ep>;
+		};
+	};
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&scmi_vdd_usb>;
+	st,current-boost-microamp = <1000>;
+	st,decrease-hs-slew-rate;
+	st,tune-hs-dc-level = <2>;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <11>;
+	st,trim-hs-impedance = <2>;
+	st,tune-squelch-level = <1>;
+	st,enable-hs-rx-gain-eq;
+	st,no-hs-ftime-ctrl;
+	st,no-lsfs-sc;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&scmi_vdd_usb>;
+	st,current-boost-microamp = <1000>;
+	st,decrease-hs-slew-rate;
+	st,tune-hs-dc-level = <2>;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <11>;
+	st,trim-hs-impedance = <2>;
+	st,tune-squelch-level = <1>;
+	st,enable-hs-rx-gain-eq;
+	st,no-hs-ftime-ctrl;
+	st,no-lsfs-sc;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp13xc.dtsi b/arch/arm/boot/dts/st/stm32mp13xc.dtsi
new file mode 100644
index 000000000000..4d00e7592882
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp13xc.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	soc {
+		cryp: crypto@54002000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54002000 0x400>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp13xf.dtsi b/arch/arm/boot/dts/st/stm32mp13xf.dtsi
new file mode 100644
index 000000000000..4d00e7592882
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp13xf.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	soc {
+		cryp: crypto@54002000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54002000 0x400>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
new file mode 100644
index 000000000000..ae83e7b10232
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
@@ -0,0 +1,3168 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+	/omit-if-no-ref/
+	adc1_ain_pins_a: adc1-ain-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* ADC1_INP2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ADC1_INP5 */
+				 <STM32_PINMUX('B', 0, ANALOG)>, /* ADC1_INP9 */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* ADC1_INP10 */
+				 <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1_INP13 */
+				 <STM32_PINMUX('A', 3, ANALOG)>; /* ADC1_INP15 */
+		};
+	};
+
+	/omit-if-no-ref/
+	adc1_in6_pins_a: adc1-in6-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 12, ANALOG)>;
+		};
+	};
+
+	/omit-if-no-ref/
+	adc12_ain_pins_a: adc12-ain-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1 in13 */
+				 <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+				 <STM32_PINMUX('F', 13, ANALOG)>, /* ADC2 in2 */
+				 <STM32_PINMUX('F', 14, ANALOG)>; /* ADC2 in6 */
+		};
+	};
+
+	/omit-if-no-ref/
+	adc12_ain_pins_b: adc12-ain-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+				 <STM32_PINMUX('F', 13, ANALOG)>; /* ADC2 in2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	adc12_usb_cc_pins_a: adc12-usb-cc-pins-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* ADC12 in18 */
+				 <STM32_PINMUX('A', 5, ANALOG)>; /* ADC12 in19 */
+		};
+	};
+
+	/omit-if-no-ref/
+	cec_pins_a: cec-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 15, AF4)>;
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	cec_sleep_pins_a: cec-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 15, ANALOG)>; /* HDMI_CEC */
+		};
+	};
+
+	/omit-if-no-ref/
+	cec_pins_b: cec-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF5)>;
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	cec_sleep_pins_b: cec-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* HDMI_CEC */
+		};
+	};
+
+	/omit-if-no-ref/
+	dac_ch1_pins_a: dac-ch1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>;
+		};
+	};
+
+	/omit-if-no-ref/
+	dac_ch2_pins_a: dac-ch2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 5, ANALOG)>;
+		};
+	};
+
+	/omit-if-no-ref/
+	dcmi_pins_a: dcmi-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 8,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('H', 9,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('H', 12, AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('B', 8,  AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  AF13)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  AF13)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  AF13)>,/* DCMI_D9 */
+				 <STM32_PINMUX('I', 3,  AF13)>,/* DCMI_D10 */
+				 <STM32_PINMUX('H', 15, AF13)>;/* DCMI_D11 */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	dcmi_sleep_pins_a: dcmi-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 8,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('H', 9,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('H', 12, ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('B', 8,  ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  ANALOG)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  ANALOG)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  ANALOG)>,/* DCMI_D9 */
+				 <STM32_PINMUX('I', 3,  ANALOG)>,/* DCMI_D10 */
+				 <STM32_PINMUX('H', 15, ANALOG)>;/* DCMI_D11 */
+		};
+	};
+
+	/omit-if-no-ref/
+	dcmi_pins_b: dcmi-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('C', 6,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1,  AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('E', 11, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('D', 3,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('E', 13, AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('B', 9,  AF13)>;/* DCMI_D7 */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	dcmi_sleep_pins_b: dcmi-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('C', 6,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1,  ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('E', 11, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('D', 3,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('E', 13, ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('B', 9,  ANALOG)>;/* DCMI_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	dcmi_pins_c: dcmi-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('A', 9,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('E', 0, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1, AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('I', 6,  AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  AF13)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  AF13)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  AF13)>;/* DCMI_D9 */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	dcmi_sleep_pins_c: dcmi-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('A', 9,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('E', 0, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1, ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('I', 6,  ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  ANALOG)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  ANALOG)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  ANALOG)>;/* DCMI_D9 */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_pins_a: rgmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('B', 0, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_sleep_pins_a: rgmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('B', 0, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_pins_b: rgmii-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_sleep_pins_b: rgmii-sleep-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		 };
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_pins_c: rgmii-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('G', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_sleep_pins_c: rgmii-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_pins_d: rgmii-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 13, AF11)>,	/* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>,	/* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>,	/* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_sleep_pins_d: rgmii-sleep-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_pins_e: rgmii-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>; /* ETH_RGMII_TX_CTL */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rgmii_sleep_pins_e: rgmii-sleep-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF0)>,   /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_sleep_pins_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_pins_b: rmii-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 5, AF0)>, /* ETH1_CLK */
+				<STM32_PINMUX('C', 1, AF11)>, /* ETH1_MDC */
+				<STM32_PINMUX('G', 13, AF11)>, /* ETH1_TXD0 */
+				<STM32_PINMUX('G', 14, AF11)>; /* ETH1_TXD1 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH1_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('A', 7, AF11)>, /* ETH1_CRS_DV */
+				<STM32_PINMUX('C', 4, AF11)>, /* ETH1_RXD0 */
+				<STM32_PINMUX('C', 5, AF11)>; /* ETH1_RXD1 */
+			bias-disable;
+		};
+		pins4 {
+			pinmux = <STM32_PINMUX('B', 11, AF11)>; /* ETH1_TX_EN */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_sleep_pins_b: rmii-sleep-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
+				<STM32_PINMUX('A', 7, ANALOG)>, /* ETH1_CRS_DV */
+				<STM32_PINMUX('B', 5, ANALOG)>, /* ETH1_CLK */
+				<STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_TX_EN */
+				<STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
+				<STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RXD0 */
+				<STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RXD1 */
+				<STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_TXD0 */
+				<STM32_PINMUX('G', 14, ANALOG)>; /* ETH1_TXD1 */
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_pins_c: rmii-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	ethernet0_rmii_sleep_pins_c: rmii-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
+	/omit-if-no-ref/
+	fmc_pins_a: fmc-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, AF12)>, /* FMC_NWE */
+				 <STM32_PINMUX('D', 11, AF12)>, /* FMC_A16_FMC_CLE */
+				 <STM32_PINMUX('D', 12, AF12)>, /* FMC_A17_FMC_ALE */
+				 <STM32_PINMUX('D', 14, AF12)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, AF12)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, AF12)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, AF12)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, AF12)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, AF12)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, AF12)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, AF12)>, /* FMC_D7 */
+				 <STM32_PINMUX('G', 9, AF12)>; /* FMC_NE2_FMC_NCE */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF12)>; /* FMC_NWAIT */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	fmc_sleep_pins_a: fmc-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, ANALOG)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* FMC_NWE */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* FMC_A16_FMC_CLE */
+				 <STM32_PINMUX('D', 12, ANALOG)>, /* FMC_A17_FMC_ALE */
+				 <STM32_PINMUX('D', 14, ANALOG)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, ANALOG)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, ANALOG)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, ANALOG)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, ANALOG)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, ANALOG)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, ANALOG)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, ANALOG)>, /* FMC_D7 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* FMC_NWAIT */
+				 <STM32_PINMUX('G', 9, ANALOG)>; /* FMC_NE2_FMC_NCE */
+		};
+	};
+
+	/omit-if-no-ref/
+	fmc_pins_b: fmc-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, AF12)>, /* FMC_NWE */
+				 <STM32_PINMUX('B', 7, AF12)>, /* FMC_NL */
+				 <STM32_PINMUX('D', 14, AF12)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, AF12)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, AF12)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, AF12)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, AF12)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, AF12)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, AF12)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, AF12)>, /* FMC_D7 */
+				 <STM32_PINMUX('E', 11, AF12)>, /* FMC_D8 */
+				 <STM32_PINMUX('E', 12, AF12)>, /* FMC_D9 */
+				 <STM32_PINMUX('E', 13, AF12)>, /* FMC_D10 */
+				 <STM32_PINMUX('E', 14, AF12)>, /* FMC_D11 */
+				 <STM32_PINMUX('E', 15, AF12)>, /* FMC_D12 */
+				 <STM32_PINMUX('D', 8, AF12)>, /* FMC_D13 */
+				 <STM32_PINMUX('D', 9, AF12)>, /* FMC_D14 */
+				 <STM32_PINMUX('D', 10, AF12)>, /* FMC_D15 */
+				 <STM32_PINMUX('G', 9, AF12)>, /* FMC_NE2_FMC_NCE */
+				 <STM32_PINMUX('G', 12, AF12)>; /* FMC_NE4 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+	};
+
+	/omit-if-no-ref/
+	fmc_sleep_pins_b: fmc-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, ANALOG)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* FMC_NWE */
+				 <STM32_PINMUX('B', 7, ANALOG)>, /* FMC_NL */
+				 <STM32_PINMUX('D', 14, ANALOG)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, ANALOG)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, ANALOG)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, ANALOG)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, ANALOG)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, ANALOG)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, ANALOG)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, ANALOG)>, /* FMC_D7 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* FMC_D8 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* FMC_D9 */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* FMC_D10 */
+				 <STM32_PINMUX('E', 14, ANALOG)>, /* FMC_D11 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* FMC_D12 */
+				 <STM32_PINMUX('D', 8, ANALOG)>, /* FMC_D13 */
+				 <STM32_PINMUX('D', 9, ANALOG)>, /* FMC_D14 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* FMC_D15 */
+				 <STM32_PINMUX('G', 9, ANALOG)>, /* FMC_NE2_FMC_NCE */
+				 <STM32_PINMUX('G', 12, ANALOG)>; /* FMC_NE4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c1_sleep_pins_a: i2c1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c1_pins_b: i2c1-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c1_sleep_pins_b: i2c1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_pins_a: i2c2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_sleep_pins_a: i2c2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 4, ANALOG)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_pins_b1: i2c2-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_sleep_pins_b1: i2c2-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_pins_c: i2c2-2 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 1, AF4)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_pins_sleep_c: i2c2-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 1, ANALOG)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c5_pins_a: i2c5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('A', 12, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c5_sleep_pins_a: i2c5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('A', 12, ANALOG)>; /* I2C5_SDA */
+
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c5_pins_b: i2c5-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 0, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('D', 1, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c5_sleep_pins_b: i2c5-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 0, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('D', 1, ANALOG)>; /* I2C5_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2s2_pins_a: i2s2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 3, AF5)>, /* I2S2_SDO */
+				 <STM32_PINMUX('B', 9, AF5)>, /* I2S2_WS */
+				 <STM32_PINMUX('A', 9, AF5)>; /* I2S2_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2s2_sleep_pins_a: i2s2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 3, ANALOG)>, /* I2S2_SDO */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* I2S2_WS */
+				 <STM32_PINMUX('A', 9, ANALOG)>; /* I2S2_CK */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2s2_pins_b: i2s2-1 {
+		pins {
+			pinmux = <STM32_PINMUX('C',  3, AF5)>, /* I2S2_SDO */
+				 <STM32_PINMUX('B', 12, AF5)>, /* I2S2_WS */
+				 <STM32_PINMUX('B', 13, AF5)>; /* I2S2_CK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2s2_sleep_pins_b: i2s2-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* I2S2_SDO */
+				 <STM32_PINMUX('B', 12, ANALOG)>, /* I2S2_WS */
+				 <STM32_PINMUX('B', 13, ANALOG)>; /* I2S2_CK */
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_pins_a: ltdc-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G',  7, AF14)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('F', 10, AF14)>, /* LCD_DE */
+				 <STM32_PINMUX('H',  2, AF14)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, AF14)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LCD_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('C',  0, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, AF14)>, /* LCD_G0 */
+				 <STM32_PINMUX('E',  6, AF14)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('H', 14, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('I',  0, AF14)>, /* LCD_G5 */
+				 <STM32_PINMUX('I',  1, AF14)>, /* LCD_G6 */
+				 <STM32_PINMUX('I',  2, AF14)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, AF14)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('I',  4, AF14)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, AF14)>, /* LCD_B6 */
+				 <STM32_PINMUX('D',  8, AF14)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_sleep_pins_a: ltdc-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G',  7, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('F', 10, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('H',  2, ANALOG)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, ANALOG)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('C',  0, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, ANALOG)>, /* LCD_G0 */
+				 <STM32_PINMUX('E',  6, ANALOG)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('H', 14, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('I',  0, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('I',  1, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('I',  2, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, ANALOG)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('I',  4, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('D',  8, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_pins_b: ltdc-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 14, AF14)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('K',  7, AF14)>, /* LCD_DE */
+				 <STM32_PINMUX('I', 15, AF14)>, /* LCD_R0 */
+				 <STM32_PINMUX('J',  0, AF14)>, /* LCD_R1 */
+				 <STM32_PINMUX('J',  1, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('J',  2, AF14)>, /* LCD_R3 */
+				 <STM32_PINMUX('J',  3, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('J',  4, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('J',  5, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('J',  6, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('J',  7, AF14)>, /* LCD_G0 */
+				 <STM32_PINMUX('J',  8, AF14)>, /* LCD_G1 */
+				 <STM32_PINMUX('J',  9, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('J', 10, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('J', 11, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('K',  0, AF14)>, /* LCD_G5 */
+				 <STM32_PINMUX('K',  1, AF14)>, /* LCD_G6 */
+				 <STM32_PINMUX('K',  2, AF14)>, /* LCD_G7 */
+				 <STM32_PINMUX('J', 12, AF14)>, /* LCD_B0 */
+				 <STM32_PINMUX('J', 13, AF14)>, /* LCD_B1 */
+				 <STM32_PINMUX('J', 14, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('J', 15, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('K',  3, AF14)>, /* LCD_B4 */
+				 <STM32_PINMUX('K',  4, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('K',  5, AF14)>, /* LCD_B6 */
+				 <STM32_PINMUX('K',  6, AF14)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_sleep_pins_b: ltdc-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 14, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 12, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I', 13, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('K',  7, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('I', 15, ANALOG)>, /* LCD_R0 */
+				 <STM32_PINMUX('J',  0, ANALOG)>, /* LCD_R1 */
+				 <STM32_PINMUX('J',  1, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('J',  2, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('J',  3, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('J',  4, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('J',  5, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('J',  6, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('J',  7, ANALOG)>, /* LCD_G0 */
+				 <STM32_PINMUX('J',  8, ANALOG)>, /* LCD_G1 */
+				 <STM32_PINMUX('J',  9, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('J', 10, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('J', 11, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('K',  0, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('K',  1, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('K',  2, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('J', 12, ANALOG)>, /* LCD_B0 */
+				 <STM32_PINMUX('J', 13, ANALOG)>, /* LCD_B1 */
+				 <STM32_PINMUX('J', 14, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('J', 15, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('K',  3, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('K',  4, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('K',  5, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('K',  6, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_pins_c: ltdc-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B',  1, AF9)>,  /* LTDC_R6 */
+				 <STM32_PINMUX('B',  9, AF14)>, /* LTDC_B7 */
+				 <STM32_PINMUX('C',  0, AF14)>, /* LTDC_R5 */
+				 <STM32_PINMUX('D',  3, AF14)>, /* LTDC_G7 */
+				 <STM32_PINMUX('D',  6, AF14)>, /* LTDC_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LTDC_B3 */
+				 <STM32_PINMUX('E', 11, AF14)>, /* LTDC_G3 */
+				 <STM32_PINMUX('E', 12, AF14)>, /* LTDC_B4 */
+				 <STM32_PINMUX('E', 13, AF14)>, /* LTDC_DE */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LTDC_R7 */
+				 <STM32_PINMUX('H',  4, AF9)>,  /* LTDC_G5 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LTDC_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>, /* LTDC_R4 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LTDC_G2 */
+				 <STM32_PINMUX('H', 15, AF14)>, /* LTDC_G4 */
+				 <STM32_PINMUX('I',  1, AF14)>, /* LTDC_G6 */
+				 <STM32_PINMUX('I',  5, AF14)>, /* LTDC_B5 */
+				 <STM32_PINMUX('I',  6, AF14)>, /* LTDC_B6 */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, AF14)>; /* LTDC_HSYNC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 14, AF14)>; /* LTDC_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_sleep_pins_c: ltdc-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 1, ANALOG)>,  /* LTDC_R6 */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* LTDC_B7 */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* LTDC_R5 */
+				 <STM32_PINMUX('D', 3, ANALOG)>, /* LTDC_G7 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* LTDC_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LTDC_B3 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* LTDC_G3 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* LTDC_B4 */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* LTDC_DE */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LTDC_R7 */
+				 <STM32_PINMUX('H', 4, ANALOG)>,  /* LTDC_G5 */
+				 <STM32_PINMUX('H', 8, ANALOG)>, /* LTDC_R2 */
+				 <STM32_PINMUX('H', 9, ANALOG)>, /* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* LTDC_R4 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LTDC_G2 */
+				 <STM32_PINMUX('H', 15, ANALOG)>, /* LTDC_G4 */
+				 <STM32_PINMUX('I', 1, ANALOG)>, /* LTDC_G6 */
+				 <STM32_PINMUX('I', 5, ANALOG)>, /* LTDC_B5 */
+				 <STM32_PINMUX('I', 6, ANALOG)>, /* LTDC_B6 */
+				 <STM32_PINMUX('I', 9, ANALOG)>, /* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LTDC_HSYNC */
+				 <STM32_PINMUX('E', 14, ANALOG)>; /* LTDC_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_pins_d: ltdc-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G',  7, AF14)>; /* LCD_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('E', 13, AF14)>, /* LCD_DE */
+				 <STM32_PINMUX('G', 13, AF14)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, AF14)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LCD_R3 */
+				 <STM32_PINMUX('A',  5, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('H', 11, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, AF14)>, /* LCD_G0 */
+				 <STM32_PINMUX('B',  0, AF14)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('E', 11, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('H',  4,  AF9)>, /* LCD_G5 */
+				 <STM32_PINMUX('I', 11,  AF9)>, /* LCD_G6 */
+				 <STM32_PINMUX('G',  8, AF14)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, AF14)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('E', 12, AF14)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, AF14)>, /* LCD_B6 */
+				 <STM32_PINMUX('I',  7, AF14)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_sleep_pins_d: ltdc-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('G',  7, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, ANALOG)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('A',  5, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('H', 11, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, ANALOG)>, /* LCD_G0 */
+				 <STM32_PINMUX('B',  0, ANALOG)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('H',  4, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('I', 11, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('G',  8, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, ANALOG)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('I',  7, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_pins_e: ltdc-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H',  2, AF14)>, /* LTDC_R0 */
+				 <STM32_PINMUX('H',  3, AF14)>, /* LTDC_R1 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LTDC_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>, /* LTDC_R4 */
+				 <STM32_PINMUX('C',  0, AF14)>, /* LTDC_R5 */
+				 <STM32_PINMUX('H', 12, AF14)>, /* LTDC_R6 */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LTDC_R7 */
+				 <STM32_PINMUX('E', 14, AF13)>, /* LTDC_G0 */
+				 <STM32_PINMUX('E',  6, AF14)>, /* LTDC_G1 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LTDC_G2 */
+				 <STM32_PINMUX('H', 14, AF14)>, /* LTDC_G3 */
+				 <STM32_PINMUX('H',  4, AF14)>, /* LTDC_G4 */
+				 <STM32_PINMUX('I',  0, AF14)>, /* LTDC_G5 */
+				 <STM32_PINMUX('I',  1, AF14)>, /* LTDC_G6 */
+				 <STM32_PINMUX('I',  2, AF14)>, /* LTDC_G7 */
+				 <STM32_PINMUX('D',  9, AF14)>, /* LTDC_B0 */
+				 <STM32_PINMUX('G', 12, AF14)>, /* LTDC_B1 */
+				 <STM32_PINMUX('G', 10, AF14)>, /* LTDC_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LTDC_B3 */
+				 <STM32_PINMUX('E', 12, AF14)>, /* LTDC_B4 */
+				 <STM32_PINMUX('A',  3, AF14)>, /* LTDC_B5 */
+				 <STM32_PINMUX('B',  8, AF14)>, /* LTDC_B6 */
+				 <STM32_PINMUX('D',  8, AF14)>, /* LTDC_B7 */
+				 <STM32_PINMUX('F', 10, AF14)>, /* LTDC_DE */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, AF14)>; /* LTDC_HSYNC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 7, AF14)>; /* LTDC_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ltdc_sleep_pins_e: ltdc-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('H',  2, ANALOG)>, /* LTDC_R0 */
+				 <STM32_PINMUX('H',  3, ANALOG)>, /* LTDC_R1 */
+				 <STM32_PINMUX('H',  8, ANALOG)>, /* LTDC_R2 */
+				 <STM32_PINMUX('H',  9, ANALOG)>, /* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* LTDC_R4 */
+				 <STM32_PINMUX('C',  0, ANALOG)>, /* LTDC_R5 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* LTDC_R6 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LTDC_R7 */
+				 <STM32_PINMUX('D',  9, ANALOG)>, /* LTDC_B0 */
+				 <STM32_PINMUX('G', 12, ANALOG)>, /* LTDC_B1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* LTDC_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LTDC_B3 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* LTDC_B4 */
+				 <STM32_PINMUX('A',  3, ANALOG)>, /* LTDC_B5 */
+				 <STM32_PINMUX('B',  8, ANALOG)>, /* LTDC_B6 */
+				 <STM32_PINMUX('D',  8, ANALOG)>, /* LTDC_B7 */
+				 <STM32_PINMUX('E', 14, ANALOG)>, /* LTDC_G0 */
+				 <STM32_PINMUX('E',  6, ANALOG)>, /* LTDC_G1 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LTDC_G2 */
+				 <STM32_PINMUX('H', 14, ANALOG)>, /* LTDC_G3 */
+				 <STM32_PINMUX('H',  4, ANALOG)>, /* LTDC_G4 */
+				 <STM32_PINMUX('I',  0, ANALOG)>, /* LTDC_G5 */
+				 <STM32_PINMUX('I',  1, ANALOG)>, /* LTDC_G6 */
+				 <STM32_PINMUX('I',  2, ANALOG)>, /* LTDC_G7 */
+				 <STM32_PINMUX('F', 10, ANALOG)>, /* LTDC_DE */
+				 <STM32_PINMUX('I',  9, ANALOG)>, /* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LTDC_HSYNC */
+				 <STM32_PINMUX('G',  7, ANALOG)>; /* LTDC_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	mco1_pins_a: mco1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, AF2)>; /* MCO1 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	mco1_sleep_pins_a: mco1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* MCO1 */
+		};
+	};
+
+	/omit-if-no-ref/
+	mco2_pins_a: mco2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+
+	/omit-if-no-ref/
+	mco2_sleep_pins_a: mco2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_pins_a: m-can1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 9, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_sleep_pins_a: m_can1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('I', 9, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_pins_b: m-can1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 12, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 11, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_sleep_pins_b: m_can1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('A', 11, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_pins_c: m-can1-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_sleep_pins_c: m_can1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('H', 14, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_pins_d: m-can1-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 1, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 0, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can1_sleep_pins_d: m_can1-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('D', 0, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can2_pins_a: m-can2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	m_can2_sleep_pins_a: m_can2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 13, ANALOG)>, /* CAN2_TX */
+				 <STM32_PINMUX('B', 5, ANALOG)>; /* CAN2_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_pins_a: pwm1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, AF1)>, /* TIM1_CH1 */
+				 <STM32_PINMUX('E', 11, AF1)>, /* TIM1_CH2 */
+				 <STM32_PINMUX('E', 14, AF1)>; /* TIM1_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_sleep_pins_a: pwm1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, ANALOG)>, /* TIM1_CH1 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* TIM1_CH2 */
+				 <STM32_PINMUX('E', 14, ANALOG)>; /* TIM1_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_pins_b: pwm1-1 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, AF1)>; /* TIM1_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_sleep_pins_b: pwm1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, ANALOG)>; /* TIM1_CH1 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_pins_c: pwm1-2 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 11, AF1)>; /* TIM1_CH2 */
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm1_sleep_pins_c: pwm1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 11, ANALOG)>; /* TIM1_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm2_pins_a: pwm2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm2_sleep_pins_a: pwm2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 3, ANALOG)>; /* TIM2_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm3_pins_a: pwm3-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 7, AF2)>; /* TIM3_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm3_sleep_pins_a: pwm3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 7, ANALOG)>; /* TIM3_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm3_pins_b: pwm3-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, AF2)>; /* TIM3_CH2 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm3_sleep_pins_b: pwm3-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, ANALOG)>; /* TIM3_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm4_pins_a: pwm4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 14, AF2)>, /* TIM4_CH3 */
+				 <STM32_PINMUX('D', 15, AF2)>; /* TIM4_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm4_sleep_pins_a: pwm4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 14, ANALOG)>, /* TIM4_CH3 */
+				 <STM32_PINMUX('D', 15, ANALOG)>; /* TIM4_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm4_pins_b: pwm4-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, AF2)>; /* TIM4_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm4_sleep_pins_b: pwm4-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, ANALOG)>; /* TIM4_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm5_pins_a: pwm5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, AF2)>; /* TIM5_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm5_sleep_pins_a: pwm5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, ANALOG)>; /* TIM5_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm5_pins_b: pwm5-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, AF2)>, /* TIM5_CH2 */
+				 <STM32_PINMUX('H', 12, AF2)>, /* TIM5_CH3 */
+				 <STM32_PINMUX('I', 0, AF2)>; /* TIM5_CH4 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm5_sleep_pins_b: pwm5-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, ANALOG)>, /* TIM5_CH2 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* TIM5_CH3 */
+				 <STM32_PINMUX('I', 0, ANALOG)>; /* TIM5_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm8_pins_a: pwm8-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm8_sleep_pins_a: pwm8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 2, ANALOG)>; /* TIM8_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm8_pins_b: pwm8-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, AF3)>, /* TIM8_CH1 */
+				 <STM32_PINMUX('I', 6, AF3)>, /* TIM8_CH2 */
+				 <STM32_PINMUX('I', 7, AF3)>, /* TIM8_CH3 */
+				 <STM32_PINMUX('C', 9, AF3)>; /* TIM8_CH4 */
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm8_sleep_pins_b: pwm8-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, ANALOG)>, /* TIM8_CH1 */
+				 <STM32_PINMUX('I', 6, ANALOG)>, /* TIM8_CH2 */
+				 <STM32_PINMUX('I', 7, ANALOG)>, /* TIM8_CH3 */
+				 <STM32_PINMUX('C', 9, ANALOG)>; /* TIM8_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm12_pins_a: pwm12-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm12_sleep_pins_a: pwm12-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 6, ANALOG)>; /* TIM12_CH1 */
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_clk_pins_a: qspi-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_clk_sleep_pins_a: qspi-clk-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 10, ANALOG)>; /* QSPI_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_bk1_pins_a: qspi-bk1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
+				 <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
+				 <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
+				 <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_bk1_sleep_pins_a: qspi-bk1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* QSPI_BK1_IO0 */
+				 <STM32_PINMUX('F', 9, ANALOG)>, /* QSPI_BK1_IO1 */
+				 <STM32_PINMUX('F', 7, ANALOG)>, /* QSPI_BK1_IO2 */
+				 <STM32_PINMUX('F', 6, ANALOG)>; /* QSPI_BK1_IO3 */
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_bk2_pins_a: qspi-bk2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
+				 <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
+				 <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
+				 <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_bk2_sleep_pins_a: qspi-bk2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* QSPI_BK2_IO0 */
+				 <STM32_PINMUX('H', 3, ANALOG)>, /* QSPI_BK2_IO1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* QSPI_BK2_IO2 */
+				 <STM32_PINMUX('G', 7, ANALOG)>; /* QSPI_BK2_IO3 */
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_cs1_pins_a: qspi-cs1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+			bias-pull-up;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_cs1_sleep_pins_a: qspi-cs1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* QSPI_BK1_NCS */
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_cs2_pins_a: qspi-cs2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
+			bias-pull-up;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	/omit-if-no-ref/
+	qspi_cs2_sleep_pins_a: qspi-cs2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>; /* QSPI_BK2_NCS */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2a_pins_a: sai2a-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, AF10)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('I', 6, AF10)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, AF10)>, /* SAI2_FS_A */
+				 <STM32_PINMUX('E', 0, AF10)>; /* SAI2_MCLK_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2a_sleep_pins_a: sai2a-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, ANALOG)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('I', 6, ANALOG)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, ANALOG)>, /* SAI2_FS_A */
+				 <STM32_PINMUX('E', 0, ANALOG)>; /* SAI2_MCLK_A */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2a_pins_b: sai2a-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 6, AF10)>,	/* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, AF10)>,	/* SAI2_FS_A */
+				 <STM32_PINMUX('D', 13, AF10)>;	/* SAI2_SCK_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2a_sleep_pins_b: sai2a-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 6, ANALOG)>,  /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, ANALOG)>,  /* SAI2_FS_A */
+				 <STM32_PINMUX('D', 13, ANALOG)>; /* SAI2_SCK_A */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2a_pins_c: sai2a-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, AF10)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('D', 11, AF10)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('D', 12, AF10)>; /* SAI2_FS_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2a_sleep_pins_c: sai2a-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, ANALOG)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('D', 12, ANALOG)>; /* SAI2_FS_A */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_pins_a: sai2b-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('E', 13, AF10)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('E', 14, AF10)>; /* SAI2_MCLK_B */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_sleep_pins_a: sai2b-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* SAI2_SD_B */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('E', 14, ANALOG)>; /* SAI2_MCLK_B */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_pins_b: sai2b-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_sleep_pins_b: sai2b-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_pins_c: sai2b-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_sleep_pins_c: sai2b-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_pins_d: sai2b-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 2, AF10)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('C', 0, AF8)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('H', 3, AF10)>; /* SAI2_MCLK_B */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai2b_sleep_pins_d: sai2b-sleep-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('H', 3, ANALOG)>, /* SAI2_MCLK_B */
+				 <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
+		};
+	};
+
+	/omit-if-no-ref/
+	sai4a_pins_a: sai4a-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, AF10)>; /* SAI4_SD_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sai4a_sleep_pins_a: sai4a-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, ANALOG)>; /* SAI4_SD_A */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_init_pins_a: sdmmc1-b4-init-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_pins_b: sdmmc1-b4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 6, AF8)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_od_pins_b: sdmmc1-b4-od-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 6, AF8)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_sleep_pins_b: sdmmc1-b4-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 6, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_dir_init_pins_a: sdmmc1-dir-init-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+				 <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_dir_pins_b: sdmmc1-dir-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('E', 14, ANALOG)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+				 <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+				 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_pins_b: sdmmc2-b4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_b4_od_pins_b: sdmmc2-b4-od-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_pins_a: sdmmc2-d47-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_sleep_pins_a: sdmmc2-d47-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_pins_b: sdmmc2-d47-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>,  /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_pins_c: sdmmc2-d47-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 15, AF9)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_sleep_pins_c: sdmmc2-d47-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 15, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_pins_d: sdmmc2-d47-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_sleep_pins_d: sdmmc2-d47-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_pins_e: sdmmc2-d47-4 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>,	/* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>,	/* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, AF10)>,	/* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, AF9)>;	/* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc2_d47_sleep_pins_e: sdmmc2-d47-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_pins_a: sdmmc3-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('F', 5, AF9)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('F', 1, AF9)>; /* SDMMC3_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_od_pins_a: sdmmc3-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('F', 5, AF9)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('F', 1, AF9)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_sleep_pins_a: sdmmc3-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('F', 5, ANALOG)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+				 <STM32_PINMUX('F', 1, ANALOG)>; /* SDMMC3_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_pins_b: sdmmc3-b4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_od_pins_b: sdmmc3-b4-od-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc3_b4_sleep_pins_b: sdmmc3-b4-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+				 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
+	spdifrx_pins_a: spdifrx-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spdifrx_sleep_pins_a: spdifrx-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 12, ANALOG)>; /* SPDIF_IN1 */
+		};
+	};
+
+	/omit-if-no-ref/
+	spi1_pins_b: spi1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 5, AF5)>, /* SPI1_SCK */
+				 <STM32_PINMUX('B', 5, AF5)>; /* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 6, AF5)>; /* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi2_pins_a: spi2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi2_pins_b: spi2-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi2_pins_c: spi2-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-pull-down;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi4_pins_a: spi4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 12, AF5)>, /* SPI4_SCK */
+				 <STM32_PINMUX('E', 6, AF5)>;  /* SPI4_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 13, AF5)>; /* SPI4_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi5_pins_a: spi5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, AF5)>, /* SPI5_SCK */
+				 <STM32_PINMUX('F', 9, AF5)>; /* SPI5_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 8, AF5)>; /* SPI5_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	stusb1600_pins_a: stusb1600-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 11, GPIO)>;
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_pins_a: uart4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_idle_pins_a: uart4-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_sleep_pins_a: uart4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_pins_b: uart4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_pins_c: uart4-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_pins_d: uart4-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_idle_pins_d: uart4-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart4_sleep_pins_d: uart4-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	uart5_pins_a: uart5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 5, AF12)>; /* UART5_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart7_pins_a: uart7-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART7_RX */
+				 <STM32_PINMUX('E', 10, AF7)>, /* UART7_CTS */
+				 <STM32_PINMUX('E', 9, AF7)>; /* UART7_RTS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart7_pins_b: uart7-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, AF7)>; /* UART7_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 6, AF7)>; /* UART7_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart7_pins_c: uart7-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>; /* UART7_RX */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart7_idle_pins_c: uart7-idle-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* UART7_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>; /* UART7_RX */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart7_sleep_pins_c: uart7-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* UART7_TX */
+				 <STM32_PINMUX('E', 7, ANALOG)>; /* UART7_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	uart8_pins_a: uart8-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 0, AF8)>; /* UART8_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	uart8_rtscts_pins_a: uart8rtscts-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 7, AF8)>, /* UART8_RTS */
+				 <STM32_PINMUX('G', 10, AF8)>; /* UART8_CTS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart1_pins_a: usart1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 12, AF7)>; /* USART1_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 11, AF7)>; /* USART1_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart1_idle_pins_a: usart1-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* USART1_RTS */
+				 <STM32_PINMUX('A', 11, AF7)>; /* USART1_CTS_NSS */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart1_sleep_pins_a: usart1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* USART1_RTS */
+				 <STM32_PINMUX('A', 11, ANALOG)>; /* USART1_CTS_NSS */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_pins_a: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_sleep_pins_a: usart2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_pins_b: usart2-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
+				 <STM32_PINMUX('A', 1, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 4, AF7)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 15, AF7)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_sleep_pins_b: usart2-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 15, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_pins_c: usart2-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 5, AF7)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_idle_pins_c: usart2-idle-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_sleep_pins_c: usart2-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_pins_a: usart3-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_idle_pins_a: usart3-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>; /* USART3_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_sleep_pins_a: usart3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_pins_b: usart3-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+				 <STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_idle_pins_b: usart3-idle-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_sleep_pins_b: usart3-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_pins_c: usart3-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+				 <STM32_PINMUX('B', 13, AF7)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_idle_pins_c: usart3-idle-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_sleep_pins_c: usart3-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('B', 13, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_pins_d: usart3-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 9, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_idle_pins_d: usart3-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 9, AF7)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_sleep_pins_d: usart3-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('D', 9, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_pins_e: usart3-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_idle_pins_e: usart3-idle-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_sleep_pins_e: usart3-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 11, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart3_pins_f: usart3-5 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usbotg_hs_pins_a: usbotg-hs-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
+		};
+	};
+
+	/omit-if-no-ref/
+	usbotg_fs_dp_dm_pins_a: usbotg-fs-dp-dm-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* OTG_FS_DM */
+				 <STM32_PINMUX('A', 12, ANALOG)>; /* OTG_FS_DP */
+		};
+	};
+};
+
+&pinctrl_z {
+	/omit-if-no-ref/
+	i2c2_pins_b2: i2c2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 0, AF3)>; /* I2C2_SCL */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_sleep_pins_b2: i2c2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 0, ANALOG)>; /* I2C2_SCL */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c4_pins_a: i2c4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
+				 <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c4_sleep_pins_a: i2c4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 4, ANALOG)>, /* I2C4_SCL */
+				 <STM32_PINMUX('Z', 5, ANALOG)>; /* I2C4_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c6_pins_a: i2c6-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 6, AF2)>, /* I2C6_SCL */
+				 <STM32_PINMUX('Z', 7, AF2)>; /* I2C6_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c6_sleep_pins_a: i2c6-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 6, ANALOG)>, /* I2C6_SCL */
+				 <STM32_PINMUX('Z', 7, ANALOG)>; /* I2C6_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	spi1_pins_a: spi1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 0, AF5)>, /* SPI1_SCK */
+				 <STM32_PINMUX('Z', 2, AF5)>; /* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 1, AF5)>; /* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi1_sleep_pins_a: spi1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* SPI1_SCK */
+				 <STM32_PINMUX('Z', 1, ANALOG)>, /* SPI1_MISO */
+				 <STM32_PINMUX('Z', 2, ANALOG)>; /* SPI1_MOSI */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart1_pins_b: usart1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 7, AF7)>; /* USART1_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 6, AF7)>; /* USART1_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart1_idle_pins_b: usart1-idle-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 7, ANALOG)>; /* USART1_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 6, AF7)>; /* USART1_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart1_sleep_pins_b: usart1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 7, ANALOG)>, /* USART1_TX */
+				 <STM32_PINMUX('Z', 6, ANALOG)>; /* USART1_RX */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15-scmi.dtsi b/arch/arm/boot/dts/st/stm32mp15-scmi.dtsi
new file mode 100644
index 000000000000..dc3b09f2f2af
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15-scmi.dtsi
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	firmware {
+		optee: optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+
+			scmi_voltd: protocol@17 {
+				reg = <0x17>;
+
+				scmi_reguls: regulators {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					scmi_reg11: regulator@0 {
+						reg = <0>;
+						regulator-name = "reg11";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <1100000>;
+					};
+
+					scmi_reg18: regulator@1 {
+						reg = <1>;
+						regulator-name = "reg18";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					scmi_usb33: regulator@2 {
+						reg = <2>;
+						regulator-name = "usb33";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&reg11 {
+	status = "disabled";
+};
+
+&reg18 {
+	status = "disabled";
+};
+
+&usb33 {
+	status = "disabled";
+};
+
+&usbotg_hs {
+	usb33d-supply = <&scmi_usb33>;
+};
+
+&usbphyc {
+	vdda1v1-supply = <&scmi_reg11>;
+	vdda1v8-supply = <&scmi_reg18>;
+};
+
+/delete-node/ &clk_hse;
+/delete-node/ &clk_hsi;
+/delete-node/ &clk_lse;
+/delete-node/ &clk_lsi;
+/delete-node/ &clk_csi;
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/st/stm32mp151.dtsi
index ed8b258256d7..fa4cbd312e5a 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp151.dtsi
@@ -17,22 +17,22 @@
 
 		cpu0: cpu@0 {
 			compatible = "arm,cortex-a7";
+			clock-frequency = <650000000>;
 			device_type = "cpu";
 			reg = <0>;
 		};
+	};
 
-		cpu1: cpu@1 {
-			compatible = "arm,cortex-a7";
-			device_type = "cpu";
-			reg = <1>;
-		};
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+		interrupt-parent = <&intc>;
 	};
 
 	psci {
-		compatible = "arm,psci";
+		compatible = "arm,psci-1.0";
 		method = "smc";
-		cpu_off = <0x84000002>;
-		cpu_on = <0x84000003>;
 	};
 
 	intc: interrupt-controller@a0021000 {
@@ -45,10 +45,10 @@
 
 	timer {
 		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 		interrupt-parent = <&intc>;
 	};
 
@@ -127,6 +127,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40000000 0x400>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM2_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 18 0x400 0x1>,
@@ -148,6 +150,11 @@
 				reg = <1>;
 				status = "disabled";
 			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
 		};
 
 		timers3: timer@40001000 {
@@ -155,6 +162,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001000 0x400>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM3_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 23 0x400 0x1>,
@@ -177,6 +186,11 @@
 				reg = <2>;
 				status = "disabled";
 			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
 		};
 
 		timers4: timer@40002000 {
@@ -184,6 +198,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM4_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 29 0x400 0x1>,
@@ -204,6 +220,11 @@
 				reg = <3>;
 				status = "disabled";
 			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
 		};
 
 		timers5: timer@40003000 {
@@ -211,6 +232,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40003000 0x400>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM5_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 55 0x400 0x1>,
@@ -233,6 +256,11 @@
 				reg = <4>;
 				status = "disabled";
 			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
 		};
 
 		timers6: timer@40004000 {
@@ -240,6 +268,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40004000 0x400>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM6_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 69 0x400 0x1>;
@@ -258,6 +288,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40005000 0x400>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM7_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 70 0x400 0x1>;
@@ -276,6 +308,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40006000 0x400>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM12_K>;
 			clock-names = "int";
 			status = "disabled";
@@ -298,6 +332,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40007000 0x400>;
+			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM13_K>;
 			clock-names = "int";
 			status = "disabled";
@@ -320,6 +356,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40008000 0x400>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM14_K>;
 			clock-names = "int";
 			status = "disabled";
@@ -342,8 +380,10 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x40009000 0x400>;
+			interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc LPTIM1_K>;
 			clock-names = "mux";
+			wakeup-source;
 			status = "disabled";
 
 			pwm {
@@ -430,37 +470,53 @@
 		usart2: serial@4000e000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x4000e000 0x400>;
-			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART2_K>;
+			wakeup-source;
+			dmas = <&dmamux1 43 0x400 0x15>,
+			       <&dmamux1 44 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		usart3: serial@4000f000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x4000f000 0x400>;
-			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART3_K>;
+			wakeup-source;
+			dmas = <&dmamux1 45 0x400 0x15>,
+			       <&dmamux1 46 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		uart4: serial@40010000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x40010000 0x400>;
-			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART4_K>;
+			wakeup-source;
+			dmas = <&dmamux1 63 0x400 0x15>,
+			       <&dmamux1 64 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		uart5: serial@40011000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x40011000 0x400>;
-			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART5_K>;
+			wakeup-source;
+			dmas = <&dmamux1 65 0x400 0x15>,
+			       <&dmamux1 66 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		i2c1: i2c@40012000 {
-			compatible = "st,stm32f7-i2c";
+			compatible = "st,stm32mp15-i2c";
 			reg = <0x40012000 0x400>;
 			interrupt-names = "event", "error";
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
@@ -469,11 +525,14 @@
 			resets = <&rcc I2C1_R>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x1>;
+			wakeup-source;
+			i2c-analog-filter;
 			status = "disabled";
 		};
 
 		i2c2: i2c@40013000 {
-			compatible = "st,stm32f7-i2c";
+			compatible = "st,stm32mp15-i2c";
 			reg = <0x40013000 0x400>;
 			interrupt-names = "event", "error";
 			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
@@ -482,11 +541,14 @@
 			resets = <&rcc I2C2_R>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x2>;
+			wakeup-source;
+			i2c-analog-filter;
 			status = "disabled";
 		};
 
 		i2c3: i2c@40014000 {
-			compatible = "st,stm32f7-i2c";
+			compatible = "st,stm32mp15-i2c";
 			reg = <0x40014000 0x400>;
 			interrupt-names = "event", "error";
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
@@ -495,11 +557,14 @@
 			resets = <&rcc I2C3_R>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x4>;
+			wakeup-source;
+			i2c-analog-filter;
 			status = "disabled";
 		};
 
 		i2c5: i2c@40015000 {
-			compatible = "st,stm32f7-i2c";
+			compatible = "st,stm32mp15-i2c";
 			reg = <0x40015000 0x400>;
 			interrupt-names = "event", "error";
 			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
@@ -508,6 +573,9 @@
 			resets = <&rcc I2C5_R>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x10>;
+			wakeup-source;
+			i2c-analog-filter;
 			status = "disabled";
 		};
 
@@ -515,7 +583,7 @@
 			compatible = "st,stm32-cec";
 			reg = <0x40016000 0x400>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CEC_K>, <&clk_lse>;
+			clocks = <&rcc CEC_K>, <&rcc CEC>;
 			clock-names = "cec", "hdmi-cec";
 			status = "disabled";
 		};
@@ -531,14 +599,14 @@
 
 			dac1: dac@1 {
 				compatible = "st,stm32-dac";
-				#io-channels-cells = <1>;
+				#io-channel-cells = <1>;
 				reg = <1>;
 				status = "disabled";
 			};
 
 			dac2: dac@2 {
 				compatible = "st,stm32-dac";
-				#io-channels-cells = <1>;
+				#io-channel-cells = <1>;
 				reg = <2>;
 				status = "disabled";
 			};
@@ -547,16 +615,24 @@
 		uart7: serial@40018000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x40018000 0x400>;
-			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART7_K>;
+			wakeup-source;
+			dmas = <&dmamux1 79 0x400 0x15>,
+			       <&dmamux1 80 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		uart8: serial@40019000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x40019000 0x400>;
-			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART8_K>;
+			wakeup-source;
+			dmas = <&dmamux1 81 0x400 0x15>,
+			       <&dmamux1 82 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -565,6 +641,11 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44000000 0x400>;
+			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
 			clocks = <&rcc TIM1_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 11 0x400 0x1>,
@@ -589,6 +670,11 @@
 				reg = <0>;
 				status = "disabled";
 			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
 		};
 
 		timers8: timer@44001000 {
@@ -596,6 +682,11 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44001000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
 			clocks = <&rcc TIM8_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 47 0x400 0x1>,
@@ -620,13 +711,22 @@
 				reg = <7>;
 				status = "disabled";
 			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
 		};
 
 		usart6: serial@44003000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x44003000 0x400>;
-			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART6_K>;
+			wakeup-source;
+			dmas = <&dmamux1 71 0x400 0x15>,
+			       <&dmamux1 72 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -674,6 +774,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44006000 0x400>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM15_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 105 0x400 0x1>,
@@ -701,6 +803,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44007000 0x400>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM16_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 109 0x400 0x1>,
@@ -725,6 +829,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44008000 0x400>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM17_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 111 0x400 0x1>,
@@ -773,7 +879,7 @@
 				#sound-dai-cells = <0>;
 
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x1c>;
+				reg = <0x4 0x20>;
 				clocks = <&rcc SAI1_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 87 0x400 0x01>;
@@ -783,7 +889,7 @@
 			sai1b: audio-controller@4400a024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI1_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 88 0x400 0x01>;
@@ -804,7 +910,7 @@
 			sai2a: audio-controller@4400b004 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x1c>;
+				reg = <0x4 0x20>;
 				clocks = <&rcc SAI2_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 89 0x400 0x01>;
@@ -814,7 +920,7 @@
 			sai2b: audio-controller@4400b024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI2_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 90 0x400 0x01>;
@@ -835,7 +941,7 @@
 			sai3a: audio-controller@4400c004 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x1c>;
+				reg = <0x04 0x20>;
 				clocks = <&rcc SAI3_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 113 0x400 0x01>;
@@ -845,7 +951,7 @@
 			sai3b: audio-controller@4400c024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI3_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 114 0x400 0x01>;
@@ -923,33 +1029,7 @@
 			};
 		};
 
-		m_can1: can@4400e000 {
-			compatible = "bosch,m_can";
-			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
-			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
-			status = "disabled";
-		};
-
-		m_can2: can@4400f000 {
-			compatible = "bosch,m_can";
-			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
-			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
-			status = "disabled";
-		};
-
-		dma1: dma@48000000 {
+		dma1: dma-controller@48000000 {
 			compatible = "st,stm32-dma";
 			reg = <0x48000000 0x400>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
@@ -961,12 +1041,13 @@
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc DMA1>;
+			resets = <&rcc DMA1_R>;
 			#dma-cells = <4>;
 			st,mem2mem;
 			dma-requests = <8>;
 		};
 
-		dma2: dma@48001000 {
+		dma2: dma-controller@48001000 {
 			compatible = "st,stm32-dma";
 			reg = <0x48001000 0x400>;
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
@@ -978,6 +1059,7 @@
 				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc DMA2>;
+			resets = <&rcc DMA2_R>;
 			#dma-cells = <4>;
 			st,mem2mem;
 			dma-requests = <8>;
@@ -985,12 +1067,13 @@
 
 		dmamux1: dma-router@48002000 {
 			compatible = "st,stm32h7-dmamux";
-			reg = <0x48002000 0x1c>;
+			reg = <0x48002000 0x40>;
 			#dma-cells = <3>;
 			dma-requests = <128>;
 			dma-masters = <&dma1 &dma2>;
 			dma-channels = <16>;
 			clocks = <&rcc DMAMUX>;
+			resets = <&rcc DMAMUX_R>;
 		};
 
 		adc: adc@48003000 {
@@ -1010,6 +1093,8 @@
 			adc1: adc@0 {
 				compatible = "st,stm32mp1-adc";
 				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x0>;
 				interrupt-parent = <&adc>;
 				interrupts = <0>;
@@ -1021,27 +1106,55 @@
 			adc2: adc@100 {
 				compatible = "st,stm32mp1-adc";
 				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0x100>;
 				interrupt-parent = <&adc>;
 				interrupts = <1>;
 				dmas = <&dmamux1 10 0x400 0x01>;
 				dma-names = "rx";
+				nvmem-cells = <&vrefint>;
+				nvmem-cell-names = "vrefint";
 				status = "disabled";
+				channel@13 {
+					reg = <13>;
+					label = "vrefint";
+				};
+				channel@14 {
+					reg = <14>;
+					label = "vddcore";
+				};
 			};
 		};
 
+		sdmmc3: mmc@48004000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x48004000 0x400>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC3_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC3_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
 		usbotg_hs: usb-otg@49000000 {
-			compatible = "snps,dwc2";
+			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
 			reg = <0x49000000 0x10000>;
-			clocks = <&rcc USBO_K>;
-			clock-names = "otg";
+			clocks = <&rcc USBO_K>, <&usbphyc>;
+			clock-names = "otg", "utmi";
 			resets = <&rcc USBO_R>;
 			reset-names = "dwc2";
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			g-rx-fifo-size = <256>;
+			g-rx-fifo-size = <512>;
 			g-np-tx-fifo-size = <32>;
-			g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
+			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
 			dr_mode = "otg";
+			otg-rev = <0x200>;
+			usb33d-supply = <&usb33>;
 			status = "disabled";
 		};
 
@@ -1051,10 +1164,9 @@
 			reg = <0x4c001000 0x400>;
 			st,proc-id = <0>;
 			interrupts-extended =
-				<&intc GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
-				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
-				<&exti 61 1>;
-			interrupt-names = "rx", "tx", "wakeup";
+				<&exti 61 1>,
+				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
 			clocks = <&rcc IPCC>;
 			wakeup-source;
 			status = "disabled";
@@ -1067,7 +1179,7 @@
 			resets = <&rcc CAMITF_R>;
 			clocks = <&rcc DCMI>;
 			clock-names = "mclk";
-			dmas = <&dmamux1 75 0x400 0x0d>;
+			dmas = <&dmamux1 75 0x400 0x01>;
 			dma-names = "tx";
 			status = "disabled";
 		};
@@ -1102,6 +1214,11 @@
 			};
 		};
 
+		pwr_mcu: pwr_mcu@50001014 {
+			compatible = "st,stm32mp151-pwr-mcu", "syscon";
+			reg = <0x50001014 0x4>;
+		};
+
 		exti: interrupt-controller@5000d000 {
 			compatible = "st,stm32mp1-exti", "syscon";
 			interrupt-controller;
@@ -1120,8 +1237,10 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x50021000 0x400>;
+			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc LPTIM2_K>;
 			clock-names = "mux";
+			wakeup-source;
 			status = "disabled";
 
 			pwm {
@@ -1147,8 +1266,10 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x50022000 0x400>;
+			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc LPTIM3_K>;
 			clock-names = "mux";
+			wakeup-source;
 			status = "disabled";
 
 			pwm {
@@ -1167,8 +1288,10 @@
 		lptimer4: timer@50023000 {
 			compatible = "st,stm32-lptimer";
 			reg = <0x50023000 0x400>;
+			interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc LPTIM4_K>;
 			clock-names = "mux";
+			wakeup-source;
 			status = "disabled";
 
 			pwm {
@@ -1181,8 +1304,10 @@
 		lptimer5: timer@50024000 {
 			compatible = "st,stm32-lptimer";
 			reg = <0x50024000 0x400>;
+			interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc LPTIM5_K>;
 			clock-names = "mux";
+			wakeup-source;
 			status = "disabled";
 
 			pwm {
@@ -1214,7 +1339,7 @@
 			sai4a: audio-controller@50027004 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x1c>;
+				reg = <0x04 0x20>;
 				clocks = <&rcc SAI4_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 99 0x400 0x01>;
@@ -1224,7 +1349,7 @@
 			sai4b: audio-controller@50027024 {
 				#sound-dai-cells = <0>;
 				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x1c>;
+				reg = <0x24 0x20>;
 				clocks = <&rcc SAI4_K>;
 				clock-names = "sai_ck";
 				dmas = <&dmamux1 100 0x400 0x01>;
@@ -1242,22 +1367,13 @@
 			status = "disabled";
 		};
 
-		cryp1: cryp@54001000 {
-			compatible = "st,stm32mp1-cryp";
-			reg = <0x54001000 0x400>;
-			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CRYP1>;
-			resets = <&rcc CRYP1_R>;
-			status = "disabled";
-		};
-
 		hash1: hash@54002000 {
 			compatible = "st,stm32f756-hash";
 			reg = <0x54002000 0x400>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc HASH1>;
 			resets = <&rcc HASH1_R>;
-			dmas = <&mdma1 31 0x10 0x1000A02 0x0 0x0>;
+			dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
 			dma-names = "in";
 			dma-maxburst = <2>;
 			status = "disabled";
@@ -1271,33 +1387,49 @@
 			status = "disabled";
 		};
 
-		mdma1: dma@58000000 {
+		mdma1: dma-controller@58000000 {
 			compatible = "st,stm32h7-mdma";
 			reg = <0x58000000 0x1000>;
 			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc MDMA>;
+			resets = <&rcc MDMA_R>;
 			#dma-cells = <5>;
 			dma-channels = <32>;
 			dma-requests = <48>;
 		};
 
-		fmc: nand-controller@58002000 {
-			compatible = "st,stm32mp15-fmc2";
-			reg = <0x58002000 0x1000>,
-			      <0x80000000 0x1000>,
-			      <0x88010000 0x1000>,
-			      <0x88020000 0x1000>,
-			      <0x81000000 0x1000>,
-			      <0x89010000 0x1000>,
-			      <0x89020000 0x1000>;
-			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&mdma1 20 0x10 0x12000a02 0x0 0x0>,
-			       <&mdma1 20 0x10 0x12000a08 0x0 0x0>,
-			       <&mdma1 21 0x10 0x12000a0a 0x0 0x0>;
-			dma-names = "tx", "rx", "ecc";
+		fmc: memory-controller@58002000 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp1-fmc2-ebi";
+			reg = <0x58002000 0x1000>;
 			clocks = <&rcc FMC_K>;
 			resets = <&rcc FMC_R>;
 			status = "disabled";
+
+			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+				 <4 0 0x80000000 0x10000000>; /* NAND */
+
+			nand-controller@4,0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32mp1-fmc2-nfc";
+				reg = <4 0x00000000 0x1000>,
+				      <4 0x08010000 0x1000>,
+				      <4 0x08020000 0x1000>,
+				      <4 0x01000000 0x1000>,
+				      <4 0x09010000 0x1000>,
+				      <4 0x09020000 0x1000>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+				       <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+				       <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+				dma-names = "tx", "rx", "ecc";
+				status = "disabled";
+			};
 		};
 
 		qspi: spi@58003000 {
@@ -1305,26 +1437,42 @@
 			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
 			reg-names = "qspi", "qspi_mm";
 			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&mdma1 22 0x10 0x100002 0x0 0x0>,
-			       <&mdma1 22 0x10 0x100008 0x0 0x0>;
+			dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
+			       <&mdma1 22 0x2 0x10100008 0x0 0x0>;
 			dma-names = "tx", "rx";
 			clocks = <&rcc QSPI_K>;
 			resets = <&rcc QSPI_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			status = "disabled";
 		};
 
-		sdmmc1: sdmmc@58005000 {
-			compatible = "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x10153180>;
+		sdmmc1: mmc@58005000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
 			reg = <0x58005000 0x1000>;
 			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names	= "cmd_irq";
 			clocks = <&rcc SDMMC1_K>;
 			clock-names = "apb_pclk";
 			resets = <&rcc SDMMC1_R>;
 			cap-sd-highspeed;
 			cap-mmc-highspeed;
 			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58007000 0x1000>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
 		};
 
 		crc1: crc@58009000 {
@@ -1334,12 +1482,6 @@
 			status = "disabled";
 		};
 
-		stmmac_axi_config_0: stmmac-axi-config {
-			snps,wr_osr_lmt = <0x7>;
-			snps,rd_osr_lmt = <0x7>;
-			snps,blen = <0 0 0 0 16 8 4>;
-		};
-
 		ethernet0: ethernet@5800a000 {
 			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
 			reg = <0x5800a000 0x2000>;
@@ -1349,57 +1491,50 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",
-				      "ethstp",
-				      "syscfg-clk";
+				      "eth-ck",
+				      "ptp_ref",
+				      "ethstp";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
-				 <&rcc ETHSTP>,
-				 <&rcc SYSCFG>;
+				 <&rcc ETHCK_K>,
+				 <&rcc ETHPTP_K>,
+				 <&rcc ETHSTP>;
 			st,syscon = <&syscfg 0x4>;
 			snps,mixed-burst;
 			snps,pbl = <2>;
+			snps,en-tx-lpi-clockgating;
 			snps,axi-config = <&stmmac_axi_config_0>;
 			snps,tso;
 			status = "disabled";
+
+			stmmac_axi_config_0: stmmac-axi-config {
+				snps,wr_osr_lmt = <0x7>;
+				snps,rd_osr_lmt = <0x7>;
+				snps,blen = <0 0 0 0 16 8 4>;
+			};
 		};
 
-		usbh_ohci: usbh-ohci@5800c000 {
+		usbh_ohci: usb@5800c000 {
 			compatible = "generic-ohci";
 			reg = <0x5800c000 0x1000>;
-			clocks = <&rcc USBH>;
+			clocks = <&usbphyc>, <&rcc USBH>;
 			resets = <&rcc USBH_R>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usbphyc_port0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
-		usbh_ehci: usbh-ehci@5800d000 {
+		usbh_ehci: usb@5800d000 {
 			compatible = "generic-ehci";
 			reg = <0x5800d000 0x1000>;
-			clocks = <&rcc USBH>;
+			clocks = <&usbphyc>, <&rcc USBH>;
 			resets = <&rcc USBH_R>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			companion = <&usbh_ohci>;
-			status = "disabled";
-		};
-
-		gpu: gpu@59000000 {
-			compatible = "vivante,gc";
-			reg = <0x59000000 0x800>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc GPU>, <&rcc GPU_K>;
-			clock-names = "bus" ,"core";
-			resets = <&rcc GPU_R>;
-			status = "disabled";
-		};
-
-		dsi: dsi@5a000000 {
-			compatible = "st,stm32-dsi";
-			reg = <0x5a000000 0x800>;
-			clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
-			clock-names = "pclk", "ref", "px_clk";
-			resets = <&rcc DSI_R>;
-			reset-names = "apb";
+			phys = <&usbphyc_port0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -1425,10 +1560,13 @@
 		usbphyc: usbphyc@5a006000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
+			#clock-cells = <0>;
 			compatible = "st,stm32mp1-usbphyc";
 			reg = <0x5a006000 0x1000>;
 			clocks = <&rcc USBPHY_K>;
 			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&reg11>;
+			vdda1v8-supply = <&reg18>;
 			status = "disabled";
 
 			usbphyc_port0: usb-phy@0 {
@@ -1445,8 +1583,9 @@
 		usart1: serial@5c000000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x5c000000 0x400>;
-			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART1_K>;
+			wakeup-source;
 			status = "disabled";
 		};
 
@@ -1465,7 +1604,7 @@
 		};
 
 		i2c4: i2c@5c002000 {
-			compatible = "st,stm32f7-i2c";
+			compatible = "st,stm32mp15-i2c";
 			reg = <0x5c002000 0x400>;
 			interrupt-names = "event", "error";
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
@@ -1474,6 +1613,9 @@
 			resets = <&rcc I2C4_R>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x8>;
+			wakeup-source;
+			i2c-analog-filter;
 			status = "disabled";
 		};
 
@@ -1482,15 +1624,21 @@
 			reg = <0x5c004000 0x400>;
 			clocks = <&rcc RTCAPB>, <&rcc RTC>;
 			clock-names = "pclk", "rtc_ck";
-			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
-		bsec: nvmem@5c005000 {
+		bsec: efuse@5c005000 {
 			compatible = "st,stm32mp15-bsec";
 			reg = <0x5c005000 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+			part_number_otp: part-number-otp@4 {
+				reg = <0x4 0x1>;
+			};
+			vrefint: vrefin-cal@52 {
+				reg = <0x52 0x2>;
+			};
 			ts_cal1: calib@5c {
 				reg = <0x5c 0x2>;
 			};
@@ -1500,7 +1648,7 @@
 		};
 
 		i2c6: i2c@5c009000 {
-			compatible = "st,stm32f7-i2c";
+			compatible = "st,stm32mp15-i2c";
 			reg = <0x5c009000 0x400>;
 			interrupt-names = "event", "error";
 			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
@@ -1509,14 +1657,178 @@
 			resets = <&rcc I2C6_R>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x20>;
+			wakeup-source;
+			i2c-analog-filter;
 			status = "disabled";
 		};
+
+		tamp: tamp@5c00a000 {
+			compatible = "st,stm32-tamp", "syscon", "simple-mfd";
+			reg = <0x5c00a000 0x400>;
+		};
+
+		/*
+		 * Break node order to solve dependency probe issue between
+		 * pinctrl and exti.
+		 */
+		pinctrl: pinctrl@50002000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-pinctrl";
+			ranges = <0 0x50002000 0xa400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioa: gpio@50002000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA>;
+				st,bank-name = "GPIOA";
+				status = "disabled";
+			};
+
+			gpiob: gpio@50003000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOB>;
+				st,bank-name = "GPIOB";
+				status = "disabled";
+			};
+
+			gpioc: gpio@50004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOC>;
+				st,bank-name = "GPIOC";
+				status = "disabled";
+			};
+
+			gpiod: gpio@50005000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x400>;
+				clocks = <&rcc GPIOD>;
+				st,bank-name = "GPIOD";
+				status = "disabled";
+			};
+
+			gpioe: gpio@50006000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x400>;
+				clocks = <&rcc GPIOE>;
+				st,bank-name = "GPIOE";
+				status = "disabled";
+			};
+
+			gpiof: gpio@50007000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x400>;
+				clocks = <&rcc GPIOF>;
+				st,bank-name = "GPIOF";
+				status = "disabled";
+			};
+
+			gpiog: gpio@50008000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x400>;
+				clocks = <&rcc GPIOG>;
+				st,bank-name = "GPIOG";
+				status = "disabled";
+			};
+
+			gpioh: gpio@50009000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x400>;
+				clocks = <&rcc GPIOH>;
+				st,bank-name = "GPIOH";
+				status = "disabled";
+			};
+
+			gpioi: gpio@5000a000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x400>;
+				clocks = <&rcc GPIOI>;
+				st,bank-name = "GPIOI";
+				status = "disabled";
+			};
+
+			gpioj: gpio@5000b000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x9000 0x400>;
+				clocks = <&rcc GPIOJ>;
+				st,bank-name = "GPIOJ";
+				status = "disabled";
+			};
+
+			gpiok: gpio@5000c000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xa000 0x400>;
+				clocks = <&rcc GPIOK>;
+				st,bank-name = "GPIOK";
+				status = "disabled";
+			};
+		};
+
+		pinctrl_z: pinctrl@54004000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-z-pinctrl";
+			ranges = <0 0x54004000 0x400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioz: gpio@54004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0 0x400>;
+				clocks = <&rcc GPIOZ>;
+				st,bank-name = "GPIOZ";
+				st,bank-ioport = <11>;
+				status = "disabled";
+			};
+		};
 	};
 
-	mlahb {
-		compatible = "simple-bus";
+	mlahb: ahb {
+		compatible = "st,mlahb", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
+		ranges;
 		dma-ranges = <0x00000000 0x38000000 0x10000>,
 			     <0x10000000 0x10000000 0x60000>,
 			     <0x30000000 0x30000000 0x60000>;
@@ -1527,8 +1839,11 @@
 			      <0x30000000 0x40000>,
 			      <0x38000000 0x10000>;
 			resets = <&rcc MCU_R>;
+			reset-names = "mcu_rst";
 			st,syscfg-holdboot = <&rcc 0x10C 0x1>;
-			st,syscfg-tz = <&rcc 0x000 0x1>;
+			st,syscfg-pdds = <&pwr_mcu 0x0 0x1>;
+			st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
+			st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-dhcor-testbench.dts b/arch/arm/boot/dts/st/stm32mp151a-dhcor-testbench.dts
new file mode 100644
index 000000000000..e0f828ecc2fa
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-dhcor-testbench.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-testbench.dtsi"
+
+/ {
+	model = "DH electronics STM32MP151A DHCOR Testbench";
+	compatible = "dh,stm32mp151a-dhcor-testbench",
+		     "dh,stm32mp151a-dhcor-som",
+		     "st,stm32mp151";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1a.dts b/arch/arm/boot/dts/st/stm32mp151a-prtt1a.dts
new file mode 100644
index 000000000000..75874eafde11
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1a.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1A";
+	compatible = "prt,prtt1a", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
+
+&pwm5_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+	};
+};
+
+&pwm5_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
+	};
+};
+
+&timers5 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts b/arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts
new file mode 100644
index 000000000000..c90d815f906b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts
@@ -0,0 +1,336 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1C";
+	compatible = "prt,prtt1c", "st,stm32mp151";
+
+	clock_ksz9031: clock-ksz9031 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_sja1105: clock-sja1105 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	pse_t1l1: ethernet-pse-1 {
+		compatible = "podl-pse-regulator";
+		pse-supply = <&reg_t1l1>;
+		#pse-cells = <0>;
+	};
+
+	pse_t1l2: ethernet-pse-2 {
+		compatible = "podl-pse-regulator";
+		pse-supply = <&reg_t1l2>;
+		#pse-cells = <0>;
+	};
+
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+
+	};
+
+	reg_t1l1: regulator-pse-t1l1 {
+		compatible = "regulator-fixed";
+		regulator-name = "pse-t1l1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpiog 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_t1l2: regulator-pse-t1l2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pse-t1l2";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpiog 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethernet0 {
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&gpioa {
+	gpio-line-names =
+		"", "", "", "PHY0_nRESET", "PHY0_nINT", "", "", "",
+		"", "", "", "", "", "", "", "SPI1_nSS";
+};
+
+&gpiod {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"WFM_RESET", "", "", "", "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names =
+		"SDMMC2_nRESET", "", "", "", "", "", "SPI1_nRESET", "",
+		"", "", "", "", "WFM_nIRQ", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "PHY3_nINT",
+		"PHY1_nINT", "PHY3_nRESET", "PHY2_nINT", "PHY2_nRESET",
+		"PHY1_nRESET", "SPE1_PWR", "SPE0_PWR", "";
+};
+
+&mdio0 {
+	/* All this DP83TD510E PHYs can't be probed before switch@0 is
+	 * probed so we need to use compatible with PHYid
+	 */
+	/* TI DP83TD510E */
+	t1l0_phy: ethernet-phy@6 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <6>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l1_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <7>;
+		interrupts-extended = <&gpiog 8 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+		pses = <&pse_t1l1>;
+	};
+
+	/* TI DP83TD510E */
+	t1l2_phy: ethernet-phy@10 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <10>;
+		interrupts-extended = <&gpiog 10 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+		pses = <&pse_t1l2>;
+	};
+
+	/* Micrel KSZ9031 */
+	rj45_phy: ethernet-phy@2 {
+		reg = <2>;
+		interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <1000>;
+
+		clocks = <&clock_ksz9031>;
+	};
+};
+
+&qspi {
+	status = "disabled";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc2_b4_od_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+	};
+};
+
+&sdmmc2_b4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_b4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+			 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc2_d47_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	non-removable;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	mmc@1 {
+		compatible = "prt,prtt1c-wfm200", "silabs,wf200";
+		reg = <1>;
+	};
+};
+
+&sdmmc3_b4_od_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+	};
+};
+
+&sdmmc3_b4_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+	};
+};
+
+&sdmmc3_b4_sleep_pins_b {
+	pins {
+		pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+			 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pins_b>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	switch@0 {
+		compatible = "nxp,sja1105q";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-rx-delay-us = <1>;
+		spi-tx-delay-us = <1>;
+		spi-cpha;
+
+		reset-gpios = <&gpioe 6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&clock_sja1105>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "t1l0";
+				phy-mode = "rmii";
+				phy-handle = <&t1l0_phy>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "t1l1";
+				phy-mode = "rmii";
+				phy-handle = <&t1l1_phy>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "t1l2";
+				phy-mode = "rmii";
+				phy-handle = <&t1l2_phy>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "rj45";
+				phy-handle = <&rj45_phy>;
+				phy-mode = "rgmii-id";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "cpu";
+				ethernet = <&ethernet0>;
+				phy-mode = "rmii";
+
+				fixed-link {
+					speed = <100>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1l.dtsi b/arch/arm/boot/dts/st/stm32mp151a-prtt1l.dtsi
new file mode 100644
index 000000000000..3938d357e198
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1l.dtsi
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxad-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mdio-gpio0 = &mdio0;
+		serial0 = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
+	 * stmmac MDC clock without reducing system bus rate, we need to use
+	 * gpio based MDIO bus.
+	 */
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&ethernet0_rmii_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, AF11)>; /* ETH1_RMII_TX_EN */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK input */
+			 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&ethernet0_rmii_sleep_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+			 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+			 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&iwdg2 {
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <104000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&qspi_bk1_pins_a {
+	pins1 {
+		bias-pull-up;
+		drive-push-pull;
+		slew-rate = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc1_b4_od_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&sdmmc1_b4_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart4_idle_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>; /* UART4_TX */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
+		bias-disable;
+		drive-push-pull;
+		slew-rate = <0>;
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>, /* UART4_TX */
+			<STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+	};
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&reg_3v3>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&reg_3v3>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1s.dts b/arch/arm/boot/dts/st/stm32mp151a-prtt1s.dts
new file mode 100644
index 000000000000..ad25929e64e6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1s.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1S";
+	compatible = "prt,prtt1s", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	clock-frequency = <100000>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	humidity-sensor@40 {
+		compatible = "ti,hdc1080";
+		reg = <0x40>;
+	};
+
+	co2-sensor@62 {
+		compatible = "sensirion,scd41";
+		reg = <0x62>;
+	};
+};
+
+&i2c1_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, AF5)>; /* I2C1_SDA */
+	};
+};
+
+&i2c1_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, ANALOG)>; /* I2C1_SDA */
+	};
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153.dtsi b/arch/arm/boot/dts/st/stm32mp153.dtsi
new file mode 100644
index 000000000000..486084e0b80b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp151.dtsi"
+
+/ {
+	cpus {
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			clock-frequency = <650000000>;
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	timer {
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		m_can1: can@4400e000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+
+		m_can2: can@4400f000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-dhcom-drc02.dts b/arch/arm/boot/dts/st/stm32mp153c-dhcom-drc02.dts
new file mode 100644
index 000000000000..b4e504f026ce
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-dhcom-drc02.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP153C-C065-R102-F0819-SPI-E2-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOM DRC02";
+	compatible = "dh,stm32mp153c-dhcom-drc02", "dh,stm32mp153c-dhcom-som",
+		     "st,stm32mp153";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-dhcor-drc-compact.dts b/arch/arm/boot/dts/st/stm32mp153c-dhcor-drc-compact.dts
new file mode 100644
index 000000000000..c8b9818499ea
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-dhcor-drc-compact.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * DRC Compact PCB number: 627-100 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-drc-compact.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOR DRC Compact";
+	compatible = "dh,stm32mp153c-dhcor-drc-compact",
+		     "dh,stm32mp153c-dhcor-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_c>;
+	pinctrl-1 = <&m_can1_sleep_pins_c>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157.dtsi b/arch/arm/boot/dts/st/stm32mp157.dtsi
new file mode 100644
index 000000000000..6197d878894d
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp153.dtsi"
+
+/ {
+	soc {
+		gpu: gpu@59000000 {
+			compatible = "vivante,gc";
+			reg = <0x59000000 0x800>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc GPU>, <&rcc GPU_K>;
+			clock-names = "bus" ,"core";
+			resets = <&rcc GPU_R>;
+		};
+
+		dsi: dsi@5a000000 {
+			compatible = "st,stm32-dsi";
+			reg = <0x5a000000 0x800>;
+			clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
+			clock-names = "pclk", "ref", "px_clk";
+			phy-dsi-supply = <&reg18>;
+			resets = <&rcc DSI_R>;
+			reset-names = "apb";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dsi_out: endpoint {
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/st/stm32mp157a-avenger96.dts
new file mode 100644
index 000000000000..8a6eaca994d1
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-avenger96.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+/* This DT is here only for backward compatibility */
+#include "stm32mp157a-dhcor-avenger96.dts"
diff --git a/arch/arm/boot/dts/st/stm32mp157a-dhcor-avenger96.dts b/arch/arm/boot/dts/st/stm32mp157a-dhcor-avenger96.dts
new file mode 100644
index 000000000000..275167f26fd9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-dhcor-avenger96.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * Avenger96 PCB number: 588-200 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP157A Avenger96 board";
+	compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som",
+		     "st,stm32mp157";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "disabled";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-dk1-scmi.dts b/arch/arm/boot/dts/st/stm32mp157a-dk1-scmi.dts
new file mode 100644
index 000000000000..ce5937270aa1
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-dk1-scmi.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157a-dk1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 SCMI Discovery Board";
+	compatible = "st,stm32mp157a-dk1-scmi", "st,stm32mp157";
+
+	reserved-memory {
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&dsi {
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names = "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-dk1.dts b/arch/arm/boot/dts/st/stm32mp157a-dk1.dts
new file mode 100644
index 000000000000..0da3667ab1e0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-dk1.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp15xx-dkx.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
+	compatible = "st,stm32mp157a-dk1", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts
new file mode 100644
index 000000000000..df97e03d2a5a
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 C.TOUCH 2.0 10.1\" Open Frame";
+	compatible = "engicam,icore-stm32mp1-ctouch2-of10",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	panel {
+		compatible = "ampire,am-1280800n3tzqw-t00h";
+		backlight = <&backlight>;
+		power-supply = <&v3v3>;
+
+		port {
+			panel_in_lvds: endpoint {
+				remote-endpoint = <&bridge_out>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+};
+
+&dsi_in {
+	remote-endpoint = <&ltdc_ep0_out>;
+};
+
+&dsi_out {
+	remote-endpoint = <&bridge_in>;
+};
+
+&i2c6 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_a>;
+	pinctrl-1 = <&i2c6_sleep_pins_a>;
+	status = "okay";
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+					data-lanes = <1 2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out: endpoint {
+					remote-endpoint = <&panel_in_lvds>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2.dts b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2.dts
new file mode 100644
index 000000000000..60ce4425a7fd
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2.dts
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 C.TOUCH 2.0";
+	compatible = "engicam,icore-stm32mp1-ctouch2",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts
new file mode 100644
index 000000000000..f8e404346396
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit";
+	compatible = "engicam,icore-stm32mp1-edimm2.2",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	panel {
+		compatible = "yes-optoelectronics,ytc700tlag-05-201c";
+		backlight = <&backlight>;
+		power-supply = <&v3v3>;
+
+		port {
+			panel_out_bridge: endpoint {
+				remote-endpoint = <&bridge_out_panel>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+};
+
+&dsi_in {
+	remote-endpoint = <&ltdc_out_dsi>;
+};
+
+&dsi_out {
+	remote-endpoint = <&bridge_in_dsi>;
+};
+
+&i2c6 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_a>;
+	pinctrl-1 = <&i2c6_sleep_pins_a>;
+	status = "okay";
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi: endpoint {
+					remote-endpoint = <&dsi_out>;
+					data-lanes = <1 2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out_panel: endpoint {
+					remote-endpoint = <&panel_out_bridge>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_out_dsi: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1.dtsi b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1.dtsi
new file mode 100644
index 000000000000..569a7e940ecc
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1.dtsi
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/ {
+	compatible = "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	vddcore: regulator-vddcore {
+		compatible = "regulator-fixed";
+		regulator-name = "vddcore";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
+
+	vdd: regulator-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_usb: regulator-vdd-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_usb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdda: regulator-vdda {
+		compatible = "regulator-fixed";
+		regulator-name = "vdda";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_ddr: regulator-vdd-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+	};
+
+	vtt_ddr: regulator-vtt-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_ddr";
+		regulator-min-microvolt = <675000>;
+		regulator-max-microvolt = <675000>;
+		regulator-always-on;
+		vin-supply = <&vdd>;
+	};
+
+	vref_ddr: regulator-vref-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vref_ddr";
+		regulator-min-microvolt = <675000>;
+		regulator-max-microvolt = <675000>;
+		regulator-always-on;
+		vin-supply = <&vdd>;
+	};
+
+	vdd_sd: regulator-vdd-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	v2v8: regulator-v2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "v2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+		vin-supply = <&v3v3>;
+	};
+
+	v1v8: regulator-v1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "v1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&v3v3>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-iot-box.dts b/arch/arm/boot/dts/st/stm32mp157a-iot-box.dts
new file mode 100644
index 000000000000..6a5a4af25bd9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-iot-box.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+#include "stm32mp157a-stinger96.dtsi"
+
+/ {
+	model = "Shiratech STM32MP157A IoT Box";
+	compatible = "shiratech,stm32mp157a-iot-box", "st,stm32mp157";
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&i2c2 {
+	ccs811@5b {
+		compatible = "ams,ccs811";
+		reg = <0x5b>;
+		wakeup-gpios = <&gpioa 12 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* WiFi */
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <1>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* Bluetooth */
+&uart4 {
+	/* Note: HW flow control is broken, hence using custom CTS/RTS gpios */
+	/delete-property/st,hw-flow-ctrl;
+	cts-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpiob 0 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	bluetooth {
+		shutdown-gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <115200>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
new file mode 100644
index 000000000000..5116a7785201
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-microgea-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam MicroGEA STM32MP1 MicroDev 2.0 7\" Open Frame";
+	compatible = "engicam,microgea-stm32mp1-microdev2.0-of7",
+		     "engicam,microgea-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiof 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		power-supply = <&panel_pwr>;
+	};
+
+	panel_pwr: regulator-panel-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiob 10 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+
+	panel {
+		compatible = "auo,b101aw03";
+		backlight = <&backlight>;
+		enable-gpios = <&gpiof 2 GPIO_ACTIVE_HIGH>;
+		power-supply = <&lcd_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	status = "okay";
+};
+
+&ltdc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ltdc_pins>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&pinctrl {
+	ltdc_pins: ltdc-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 10, AF14)>,	/* LTDC_B2 */
+				 <STM32_PINMUX('H', 12, AF14)>,	/* LTDC_R6 */
+				 <STM32_PINMUX('H', 11, AF14)>,	/* LTDC_R5 */
+				 <STM32_PINMUX('D', 10, AF14)>,	/* LTDC_B3 */
+				 <STM32_PINMUX('D', 9, AF14)>,	/* LTDC_B0 */
+				 <STM32_PINMUX('E', 5, AF14)>,	/* LTDC_G0 */
+				 <STM32_PINMUX('E', 6, AF14)>,	/* LTDC_G1 */
+				 <STM32_PINMUX('E', 13, AF14)>,	/* LTDC_DE */
+				 <STM32_PINMUX('E', 15, AF14)>,	/* LTDC_R7 */
+				 <STM32_PINMUX('G', 7, AF14)>,	/* LTDC_CLK */
+				 <STM32_PINMUX('G', 12, AF14)>,	/* LTDC_B1 */
+				 <STM32_PINMUX('H', 2, AF14)>,	/* LTDC_R0 */
+				 <STM32_PINMUX('H', 3, AF14)>,	/* LTDC_R1 */
+				 <STM32_PINMUX('H', 8, AF14)>,	/* LTDC_R2 */
+				 <STM32_PINMUX('H', 9, AF14)>,	/* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>,	/* LTDC_R4 */
+				 <STM32_PINMUX('H', 13, AF14)>,	/* LTDC_G2 */
+				 <STM32_PINMUX('H', 14, AF14)>,	/* LTDC_G3 */
+				 <STM32_PINMUX('H', 15, AF14)>,	/* LTDC_G4 */
+				 <STM32_PINMUX('I', 0, AF14)>,	/* LTDC_G5 */
+				 <STM32_PINMUX('I', 1, AF14)>,	/* LTDC_G6 */
+				 <STM32_PINMUX('I', 2, AF14)>,	/* LTDC_G7 */
+				 <STM32_PINMUX('I', 4, AF14)>,	/* LTDC_B4 */
+				 <STM32_PINMUX('I', 5, AF14)>,	/* LTDC_B5 */
+				 <STM32_PINMUX('B', 8, AF14)>,	/* LTDC_B6 */
+				 <STM32_PINMUX('I', 7, AF14)>,	/* LTDC_B7 */
+				 <STM32_PINMUX('I', 9, AF14)>,	/* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, AF14)>;	/* LTDC_HSYNC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* J31: RS323 */
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0.dts b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
new file mode 100644
index 000000000000..d949559be020
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-microgea-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam MicroGEA STM32MP1 MicroDev 2.0 Carrier Board";
+	compatible = "engicam,microgea-stm32mp1-microdev2.0",
+		     "engicam,microgea-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* J31: RS323 */
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1.dtsi b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1.dtsi
new file mode 100644
index 000000000000..a75f50cf7123
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1.dtsi
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/ {
+	compatible = "engicam,microgea-stm32mp1", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x10000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	vin: regulator-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddcore: regulator-vddcore {
+		compatible = "regulator-fixed";
+		regulator-name = "vddcore";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+
+	vdd: regulator-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+
+	vddq_ddr: regulator-vddq-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vddq_ddr";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_a>;
+	pinctrl-1 = <&fmc_sleep_pins_a>;
+	status = "okay";
+
+	nand-controller@4,0 {
+		status = "okay";
+
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-stinger96.dts b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dts
new file mode 100644
index 000000000000..249a53877512
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+#include "stm32mp157a-stinger96.dtsi"
+
+/ {
+	model = "Shiratech STM32MP157A Stinger96 board";
+	compatible = "shiratech,stm32mp157a-stinger96", "st,stm32mp157";
+};
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dtsi
index 628c74a45a25..5c1cc48e5199 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dtsi
@@ -1,117 +1,93 @@
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Manivannan Sadhasivam
  */
 
 /dts-v1/;
 
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xac-pinctrl.dtsi"
+#include "stm32mp157.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/mfd/st,stpmic1.h>
 
 / {
-	model = "Arrow Electronics STM32MP157A Avenger96 board";
-	compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
-
 	aliases {
-		ethernet0 = &ethernet0;
 		mmc0 = &sdmmc1;
 		serial0 = &uart4;
 		serial1 = &uart7;
+		serial2 = &usart2;
+		spi0 = &spi4;
 	};
 
 	chosen {
-		stdout-path = "serial0:115200n8";
+		stdout-path = "serial1:115200n8";
 	};
 
 	memory@c0000000 {
 		device_type = "memory";
-		reg = <0xc0000000 0x40000000>;
+		reg = <0xc0000000 0x10000000>;
 	};
 
 	led {
 		compatible = "gpio-leds";
+
 		led1 {
 			label = "green:user1";
-			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
 
 		led2 {
 			label = "green:user2";
-			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpioh 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
 			default-state = "off";
 		};
 
 		led3 {
 			label = "green:user3";
-			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpioh 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc1";
 			default-state = "off";
 		};
 
 		led4 {
-			label = "green:user3";
-			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+			label = "green:user4";
+			gpios = <&gpiof 12 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "none";
 			default-state = "off";
 			panic-indicator;
 		};
-
-		led5 {
-			label = "yellow:wifi";
-			gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "phy0tx";
-			default-state = "off";
-		};
-
-		led6 {
-			label = "blue:bt";
-			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "bluetooth-power";
-			default-state = "off";
-		};
 	};
-};
 
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rgmii";
-	max-speed = <1000>;
-	phy-handle = <&phy0>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-		phy0: ethernet-phy@7 {
-			reg = <7>;
-		};
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioa 8 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
 	};
 };
 
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_b>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
+/* Only headless mode is supported */
+&gpu {
+	status = "disabled";
 };
 
+/* LS-I2C0 */
 &i2c2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <1000>;
+	i2c-scl-falling-time-ns = <300>;
 	status = "okay";
 	/delete-property/dmas;
 	/delete-property/dma-names;
@@ -129,15 +105,11 @@
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
-		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		status = "okay";
 
-		st,main-control-register = <0x04>;
-		st,vin-control-register = <0xc0>;
-		st,usb-control-register = <0x30>;
-
 		regulators {
 			compatible = "st,stpmic1-regulators";
 
@@ -160,8 +132,8 @@
 
 			vdd_ddr: buck2 {
 				regulator-name = "vdd_ddr";
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <1350000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
 				regulator-over-current-protection;
@@ -169,10 +141,10 @@
 
 			vdd: buck3 {
 				regulator-name = "vdd";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
-				st,mask_reset;
+				st,mask-reset;
 				regulator-initial-mode = <0>;
 				regulator-over-current-protection;
 			};
@@ -188,18 +160,18 @@
 
 			vdda: ldo1 {
 				regulator-name = "vdda";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 				interrupts = <IT_CURLIM_LDO1 0>;
-				interrupt-parent = <&pmic>;
 			};
 
-			v2v8: ldo2 {
-				regulator-name = "v2v8";
-				regulator-min-microvolt = <2800000>;
-				regulator-max-microvolt = <2800000>;
+			v2v9: ldo2 {
+				regulator-name = "v2v9";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-always-on;
 				interrupts = <IT_CURLIM_LDO2 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vtt_ddr: ldo3 {
@@ -212,10 +184,7 @@
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vdd_sd: ldo5 {
@@ -223,7 +192,6 @@
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO5 0>;
-				interrupt-parent = <&pmic>;
 				regulator-boot-on;
 			};
 
@@ -231,33 +199,29 @@
 				regulator-name = "v1v8";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 				interrupts = <IT_CURLIM_LDO6 0>;
-				interrupt-parent = <&pmic>;
-				regulator-enable-ramp-delay = <300000>;
 			};
 
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
 				regulator-name = "bst_out";
 				interrupts = <IT_OCP_BOOST 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				interrupt-parent = <&pmic>;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				interrupt-parent = <&pmic>;
 				regulator-active-discharge = <1>;
 			};
 		};
@@ -296,30 +260,80 @@
 
 &sdmmc1 {
 	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
-	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
-	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
 	broken-cd;
+	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
 	st,use-ckin;
 	bus-width = <4>;
 	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
 	status = "okay";
 };
 
+/* LS-SPI0 */
+&spi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi4_pins_a>;
+	cs-gpios = <&gpioe 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+/* BG96 */
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_b>;
+	pinctrl-1 = <&usart2_sleep_pins_b>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* LS-UART0 */
 &uart4 {
-	/* On Low speed expansion header */
-	label = "LS-UART1";
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins_b>;
+	pinctrl-0 = <&uart4_pins_c>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
+/* Debug console */
 &uart7 {
-	/* On Low speed expansion header */
-	label = "LS-UART0";
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart7_pins_a>;
+	pinctrl-0 = <&uart7_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/st/stm32mp157c-dhcom-pdk2.dts
new file mode 100644
index 000000000000..6dd8216c235e
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dhcom-pdk2.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
+
+/ {
+	model = "DH electronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
+		     "st,stm32mp157";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dhcom-picoitx.dts b/arch/arm/boot/dts/st/stm32mp157c-dhcom-picoitx.dts
new file mode 100644
index 000000000000..7067a860aaff
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dhcom-picoitx.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP157C-C065-R102-F0819-SPI-E-CAN2-SD-RTC-T-DSI-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * PicoITX PCB number: 487-600 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-picoitx.dtsi"
+
+/ {
+	model = "DH electronics STM32MP157C DHCOM PicoITX";
+	compatible = "dh,stm32mp157c-dhcom-picoitx", "dh,stm32mp157c-dhcom-som",
+		     "st,stm32mp157";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dk2-scmi.dts b/arch/arm/boot/dts/st/stm32mp157c-dk2-scmi.dts
new file mode 100644
index 000000000000..c20a73841c1f
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dk2-scmi.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-dk2.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-DK2 SCMI Discovery Board";
+	compatible = "st,stm32mp157c-dk2-scmi", "st,stm32mp157";
+
+	reserved-memory {
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	phy-dsi-supply = <&scmi_reg18>;
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names = "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-dk2.dts b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
index d26adcbeba33..510cca5acb79 100644
--- a/arch/arm/boot/dts/stm32mp157c-dk2.dts
+++ b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
@@ -6,37 +6,34 @@
 
 /dts-v1/;
 
-#include "stm32mp157a-dk1.dts"
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp15xx-dkx.dtsi"
 
 / {
 	model = "STMicroelectronics STM32MP157C-DK2 Discovery Board";
 	compatible = "st,stm32mp157c-dk2", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial3 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&cryp1 {
+	status = "okay";
 };
 
 &dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
-	phy-dsi-supply = <&reg18>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			dsi_in: endpoint {
-				remote-endpoint = <&ltdc_ep1_out>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-			dsi_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
 
 	panel@0 {
 		compatible = "orisetech,otm8009a";
@@ -53,6 +50,14 @@
 	};
 };
 
+&dsi_in {
+	remote-endpoint = <&ltdc_ep1_out>;
+};
+
+&dsi_out {
+	remote-endpoint = <&panel_in>;
+};
+
 &i2c1 {
 	touchscreen@38 {
 		compatible = "focaltech,ft6236";
@@ -79,3 +84,11 @@
 		};
 	};
 };
+
+&usart2 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart2_pins_c>;
+	pinctrl-1 = <&usart2_sleep_pins_c>;
+	pinctrl-2 = <&usart2_idle_pins_c>;
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-ed1-scmi.dts b/arch/arm/boot/dts/st/stm32mp157c-ed1-scmi.dts
new file mode 100644
index 000000000000..5e2eaf57ce22
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-ed1-scmi.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-ed1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-ED1 SCMI eval daughter";
+	compatible = "st,stm32mp157c-ed1-scmi", "st,stm32mp157";
+
+	reserved-memory {
+		optee@fe000000 {
+			reg = <0xfe000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names = "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/st/stm32mp157c-ed1.dts
index b8cc0fb0ec48..66ed5f9921ba 100644
--- a/arch/arm/boot/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/boot/dts/st/stm32mp157c-ed1.dts
@@ -5,8 +5,10 @@
  */
 /dts-v1/;
 
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xaa-pinctrl.dtsi"
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/mfd/st,stpmic1.h>
 
@@ -14,6 +16,10 @@
 	model = "STMicroelectronics STM32MP157C eval daughter";
 	compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
 
+	aliases {
+		serial0 = &uart4;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -63,15 +69,6 @@
 			reg = <0x38000000 0x10000>;
 			no-map;
 		};
-
-		gpu_reserved: gpu@e8000000 {
-			reg = <0xe8000000 0x8000000>;
-			no-map;
-		};
-	};
-
-	aliases {
-		serial0 = &uart4;
 	};
 
 	sd_switch: regulator-sd_switch {
@@ -87,6 +84,48 @@
 		states = <1800000 0x1>,
 			 <2900000 0x0>;
 	};
+
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	/* ANA0, ANA1 are dedicated pins and don't need pinctrl: only in6. */
+	pinctrl-0 = <&adc1_in6_pins_a>;
+	pinctrl-names = "default";
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+	adc1: adc@0 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			/* 16.5 ck_cycles sampling time */
+			st,min-sample-time-ns = <400>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <400>;
+		};
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <400>;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
 };
 
 &dac {
@@ -106,16 +145,17 @@
 	status = "okay";
 };
 
-&gpu {
-	contiguous-area = <&gpu_reserved>;
+&hash1 {
 	status = "okay";
 };
 
 &i2c4 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
 	i2c-scl-rising-time-ns = <185>;
 	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
 	status = "okay";
 	/* spare dmas for other usage */
 	/delete-property/dmas;
@@ -131,11 +171,18 @@
 
 		regulators {
 			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&vin>;
+			buck2-supply = <&vin>;
+			buck3-supply = <&vin>;
+			buck4-supply = <&vin>;
 			ldo1-supply = <&v3v3>;
 			ldo2-supply = <&v3v3>;
 			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&vin>;
 			ldo5-supply = <&v3v3>;
 			ldo6-supply = <&v3v3>;
+			vref_ddr-supply = <&vin>;
+			boost-supply = <&vin>;
 			pwr_sw1-supply = <&bst_out>;
 			pwr_sw2-supply = <&bst_out>;
 
@@ -200,8 +247,6 @@
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -223,7 +268,6 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -270,8 +314,8 @@
 &m4_rproc {
 	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
 			<&vdev0vring1>, <&vdev0buffer>;
-	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
-	mbox-names = "vq0", "vq1", "shutdown";
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
 	interrupt-parent = <&exti>;
 	interrupts = <68 1>;
 	status = "okay";
@@ -295,13 +339,34 @@
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
-	broken-cd;
+	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
 	st,use-ckin;
 	bus-width = <4>;
 	vmmc-supply = <&vdd_sd>;
 	vqmmc-supply = <&sd_switch>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	mmc-ddr-3_3v;
 	status = "okay";
 };
 
@@ -316,19 +381,23 @@
 };
 
 &uart4 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep", "idle";
 	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
+&usbotg_hs {
+	vbus-supply = <&vbus_otg>;
+};
+
 &usbphyc_port0 {
 	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
 
 &usbphyc_port1 {
 	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
diff --git a/arch/arm/boot/dts/st/stm32mp157c-emsbc-argon.dts b/arch/arm/boot/dts/st/stm32mp157c-emsbc-argon.dts
new file mode 100644
index 000000000000..a19c488cf7c8
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-emsbc-argon.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Reinhold Müller <reinhold.mueller@emtrion.de>.
+//
+
+/dts-v1/;
+
+#include "stm32mp157c-emstamp-argon.dtsi"
+
+/ {
+	model = "emtrion STM32MP157C emSBC-Argon Developer Board";
+	compatible = "emtrion,stm32mp157c-emsbc-argon", "emtrion,stm32mp157c-emstamp-argon",
+			"st,stm32mp157";
+
+	led: gpio_leds {
+		compatible = "gpio-leds";
+		led-2 {
+			label = "red";
+			gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+		led-3 {
+			label = "green";
+			gpios = <&gpioe 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+	};
+};
+
+&dac {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi b/arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi
new file mode 100644
index 000000000000..4792004cab0c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi
@@ -0,0 +1,538 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Reinhold Müller <reinhold.mueller@emtrion.de>.
+//
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+		serial1 = &usart2;
+		serial2 = &usart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x2000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x2000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10044000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10044000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	led: gpio_leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "panic";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+		led-1 {
+			label = "heartbeat";
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+	};
+};
+
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+
+	adc1: adc@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&adc1_in6_pins_a>;
+		status = "disabled";
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+
+	adc2: adc@100 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		channel@12 {
+			reg = <12>;
+			label = "sense_temp";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@15 {
+			reg = <15>;
+			label = "vbat";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@16 {
+			reg = <16>;
+			label = "dac_out1";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@17 {
+			reg = <17>;
+			label = "dac_out1";
+			st,min-sample-time-ns = <9000>;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	snps,reset-gpio = <&gpioa 1 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 30000 50000>;
+	pinctrl-0 = <&ethernet0_rmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth-ref-clk-sel;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-always-on;
+			};
+
+			vdda: ldo6 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				regulator-boot-on;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_usbh: pwr_sw2 {
+				regulator-name = "usbh_vbus";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	interrupt-names = "wdg";
+	recovery;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <133000000>;
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	arm,primecell-periphid = <0x10153180>;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	status = "disabled";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm1_pins_b>;
+		pinctrl-1 = <&pwm1_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	status = "okay";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_d>;
+	pinctrl-1 = <&usart3_sleep_pins_d>;
+	pinctrl-2 = <&usart3_idle_pins_d>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbh_ohci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-ev1-scmi.dts b/arch/arm/boot/dts/st/stm32mp157c-ev1-scmi.dts
new file mode 100644
index 000000000000..3226fb945a8e
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-ev1-scmi.dts
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-ev1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-EV1 SCMI eval daughter on eval mother";
+	compatible = "st,stm32mp157c-ev1-scmi", "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	reserved-memory {
+		optee@fe000000 {
+			reg = <0xfe000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	phy-dsi-supply = <&scmi_reg18>;
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&m_can1 {
+	clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names = "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/st/stm32mp157c-ev1.dts
index 3789312c8539..9eb9a1bf4f2c 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/st/stm32mp157c-ev1.dts
@@ -8,20 +8,21 @@
 #include "stm32mp157c-ed1.dts"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/media/video-interfaces.h>
 
 / {
 	model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
 	compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	aliases {
-		serial0 = &uart4;
+		serial1 = &usart3;
 		ethernet0 = &ethernet0;
 	};
 
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	clocks {
 		clk_ext_camera: clk-ext-camera {
 			#clock-cells = <0>;
@@ -89,6 +90,7 @@
 	port {
 		dcmi_0: endpoint {
 			remote-endpoint = <&ov5640_0>;
+			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
 			bus-width = <8>;
 			hsync-active = <0>;
 			vsync-active = <0>;
@@ -100,29 +102,9 @@
 &dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;
-	phy-dsi-supply = <&reg18>;
 	status = "okay";
 
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			dsi_in: endpoint {
-				remote-endpoint = <&ltdc_ep0_out>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-			dsi_out: endpoint {
-				remote-endpoint = <&dsi_panel_in>;
-			};
-		};
-	};
-
-	panel-dsi@0 {
+	panel@0 {
 		compatible = "raydium,rm68200";
 		reg = <0>;
 		reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
@@ -138,16 +120,24 @@
 	};
 };
 
+&dsi_in {
+	remote-endpoint = <&ltdc_ep0_out>;
+};
+
+&dsi_out {
+	remote-endpoint = <&dsi_panel_in>;
+};
+
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rgmii-id";
 	max-speed = <1000>;
 	phy-handle = <&phy0>;
 
-	mdio0 {
+	mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "snps,dwmac-mdio";
@@ -162,20 +152,23 @@
 	pinctrl-0 = <&fmc_pins_a>;
 	pinctrl-1 = <&fmc_sleep_pins_a>;
 	status = "okay";
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	nand@0 {
-		reg = <0>;
-		nand-on-flash-bbt;
-		#address-cells = <1>;
-		#size-cells = <1>;
+	nand-controller@4,0 {
+		status = "okay";
+
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
 	};
 };
 
 &i2c2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
 	i2c-scl-rising-time-ns = <185>;
 	i2c-scl-falling-time-ns = <20>;
 	status = "okay";
@@ -185,7 +178,9 @@
 		reg = <0x3c>;
 		clocks = <&clk_ext_camera>;
 		clock-names = "xclk";
+		AVDD-supply = <&v2v8>;
 		DOVDD-supply = <&v2v8>;
+		DVDD-supply = <&v2v8>;
 		powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
 		reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
 		rotation = <180>;
@@ -210,7 +205,7 @@
 		interrupt-parent = <&gpioi>;
 		vdd-supply = <&v3v3>;
 
-		stmfx_pinctrl: stmfx-pin-controller {
+		stmfx_pinctrl: pinctrl {
 			compatible = "st,stmfx-0300-pinctrl";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -218,7 +213,7 @@
 			#interrupt-cells = <2>;
 			gpio-ranges = <&stmfx_pinctrl 0 0 24>;
 
-			joystick_pins: joystick {
+			joystick_pins: joystick-pins {
 				pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
 				bias-pull-down;
 			};
@@ -227,8 +222,9 @@
 };
 
 &i2c5 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
 	i2c-scl-rising-time-ns = <185>;
 	i2c-scl-falling-time-ns = <20>;
 	status = "okay";
@@ -238,11 +234,7 @@
 	status = "okay";
 
 	port {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ltdc_ep0_out: endpoint@0 {
-			reg = <0>;
+		ltdc_ep0_out: endpoint {
 			remote-endpoint = <&dsi_in>;
 		};
 	};
@@ -257,14 +249,22 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a
+		     &qspi_bk2_pins_a
+		     &qspi_cs2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a
+		     &qspi_bk2_sleep_pins_a
+		     &qspi_cs2_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
@@ -273,7 +273,7 @@
 		#size-cells = <1>;
 	};
 
-	flash1: mx66l51235l@1 {
+	flash1: flash@1 {
 		compatible = "jedec,spi-nor";
 		reg = <1>;
 		spi-rx-bus-width = <4>;
@@ -283,6 +283,18 @@
 	};
 };
 
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "disabled";
+};
+
 &spi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi1_pins_a>;
@@ -296,7 +308,8 @@
 	status = "disabled";
 	pwm {
 		pinctrl-0 = <&pwm2_pins_a>;
-		pinctrl-names = "default";
+		pinctrl-1 = <&pwm2_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
 		status = "okay";
 	};
 	timer@1 {
@@ -310,7 +323,8 @@
 	status = "disabled";
 	pwm {
 		pinctrl-0 = <&pwm8_pins_a>;
-		pinctrl-names = "default";
+		pinctrl-1 = <&pwm8_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
 		status = "okay";
 	};
 	timer@7 {
@@ -324,7 +338,8 @@
 	status = "disabled";
 	pwm {
 		pinctrl-0 = <&pwm12_pins_a>;
-		pinctrl-names = "default";
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
 		status = "okay";
 	};
 	timer@11 {
@@ -332,17 +347,67 @@
 	};
 };
 
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_b>;
+	pinctrl-1 = <&usart3_sleep_pins_b>;
+	pinctrl-2 = <&usart3_idle_pins_b>;
+	/*
+	 * HW flow control USART3_RTS is optional, and isn't default wired to
+	 * the connector. SB23 needs to be soldered in order to use it, and R77
+	 * (ETH_CLK) should be removed.
+	 */
+	uart-has-rtscts;
+	status = "disabled";
+};
+
 &usbh_ehci {
-	phys = <&usbphyc_port0>;
 	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&v3v3>;
+	};
 };
 
 &usbotg_hs {
-	dr_mode = "peripheral";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
 	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
 	status = "okay";
 };
 
 &usbphyc {
 	status = "okay";
 };
+
+&usbphyc_port0 {
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/st/stm32mp157c-lxa-mc1.dts
new file mode 100644
index 000000000000..eada9cf257be
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-lxa-mc1.dts
@@ -0,0 +1,253 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Linux Automation MC-1 board";
+	compatible = "lxa,stm32mp157c-mc1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&backlight_pwm 1 100000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_5v2>; /* 3V3_BACKLIGHT */
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "mc1:green:act";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	led-controller-1 {
+		compatible = "pwm-leds";
+
+		/* led-1 to led-3 are part of a single RGB led */
+		led-1 {
+			label = "mc1:red:rgb";
+			pwms = <&leds_pwm 1 1000000 0>;
+			max-brightness = <255>;
+			active-low;
+		};
+
+		led-2 {
+			label = "mc1:green:rgb";
+			pwms = <&leds_pwm 2 1000000 0>;
+			max-brightness = <255>;
+			active-low;
+		};
+
+		led-3 {
+			label = "mc1:blue:rgb";
+			pwms = <&leds_pwm 3 1000000 0>;
+			max-brightness = <255>;
+			active-low;
+		};
+	};
+
+	panel: panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&backlight>;
+		enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&v3v3>;
+	};
+
+	/* supplied by either debug board or PoE */
+	reg_5v2: regulator_5v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V2";
+		regulator-min-microvolt = <5200000>;
+		regulator-max-microvolt = <5200000>;
+		regulator-always-on;
+	};
+};
+
+&ethernet0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_b>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@3 { /* KSZ9031RN */
+			reg = <3>;
+			reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+			interrupt-parent = <&gpioa>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+			micrel,force-master;
+		};
+	};
+};
+
+&gpioz {
+	gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "",
+			  "HWID4", "HWID5";
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_b>;
+	pinctrl-1 = <&i2c5_sleep_pins_b>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		interrupt-parent = <&gpiod>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>; /* TOUCH_INT# */
+		vcc-supply = <&reg_3v3>;
+		reg = <0x38>;
+		reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */
+		touchscreen-size-x = <1792>;
+		touchscreen-size-y = <1024>;
+		wakeup-source;
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_c>;
+	pinctrl-1 = <&ltdc_sleep_pins_c>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};
+
+&pmic {
+	regulators {
+		buck4-supply = <&reg_5v2>;	/* VIN */
+		ldo2-supply = <&reg_5v2>;	/* PMIC_LDO25IN */
+		ldo5-supply = <&reg_5v2>;	/* PMIC_LDO25IN */
+		boost-supply = <&reg_5v2>;	/* PMIC_BSTIN */
+		pwr_sw2-supply = <&bst_out>;    /* PMIC_SWIN */
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	bus-width = <4>;
+	cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	no-1-8-v;
+	st,neg-edge;
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc1_b4_pins_a {
+	/*
+	 * board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to
+	 * work, thus enable internal pull-ups.
+	 */
+	pins1 {
+		/delete-property/ bias-disable;
+		bias-pull-up;
+	};
+	pins2 {
+		/delete-property/ bias-disable;
+		bias-pull-up;
+	};
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+	bus-width = <8>;
+	mmc-ddr-3_3v;
+	no-1-8-v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&timers3 {
+	status = "okay";
+
+	backlight_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm3_pins_b>;
+		pinctrl-1 = <&pwm3_sleep_pins_b>;
+		status = "okay";
+	};
+};
+
+&timers5 {
+	status = "okay";
+
+	leds_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm5_pins_b>;
+		pinctrl-1 = <&pwm5_sleep_pins_b>;
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen1.dts b/arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen1.dts
new file mode 100644
index 000000000000..81f254fb88b0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen1.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+	model = "Linux Automation Test Automation Controller (TAC) Gen 1";
+	compatible = "lxa,stm32mp157c-tac-gen1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&backlight_pwm 1 1000000 0>;
+	};
+
+	reg_iobus_12v: regulator-iobus-12v {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_12v>;
+
+		gpio = <&gpioh 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "12V_IOBUS";
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "STACK_CS2", "", "STACK_CS3", /*  0 */
+	"ETH_GPIO1", "ETH_INT", "", "", "",                     /*  5 */
+	"", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP",             /* 10 */
+	"";                                                     /* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "STACK_CS1", "", "", "", /*  0 */
+	"", "", "", "", "",                            /*  5 */
+	"", "";                                        /* 10 */
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&i2c1 {
+	powerboard_gpio: gpio@24 {
+		compatible = "nxp,pca9570";
+		reg = <0x24>;
+
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-line-names = "DUT_PWR_EN", "DUT_PWR_DISCH", "DUT_PWR_ADCRST", "";
+	};
+};
+
+&spi2 {
+	adc@0 {
+		compatible = "ti,lmp92064";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		vdd-supply = <&reg_pb_3v3>;
+		vdig-supply = <&reg_pb_3v3>;
+		reset-gpios = <&powerboard_gpio 2 GPIO_ACTIVE_HIGH>;
+
+		shunt-resistor-micro-ohms = <15000>;
+	};
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	backlight_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm1_pins_c>;
+		pinctrl-1 = <&pwm1_sleep_pins_c>;
+
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen2.dts b/arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen2.dts
new file mode 100644
index 000000000000..8a34d15e9005
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen2.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+	model = "Linux Automation Test Automation Controller (TAC) Gen 2";
+	compatible = "lxa,stm32mp157c-tac-gen2", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&led_pwm 3 1000000 0>;
+	};
+
+	reg_iobus_12v: regulator-iobus-12v {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_12v>;
+		gpio = <&gpioh 13 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "12V_IOBUS";
+	};
+
+	led-controller-1 {
+		compatible = "pwm-leds-multicolor";
+
+		multi-led {
+			color = <LED_COLOR_ID_RGB>;
+			function = LED_FUNCTION_STATUS;
+			max-brightness = <65535>;
+
+			led-red {
+				active-low;
+				color = <LED_COLOR_ID_RED>;
+				pwms = <&led_pwm 0 1000000 0>;
+			};
+
+			led-green {
+				active-low;
+				color = <LED_COLOR_ID_GREEN>;
+				pwms = <&led_pwm 2 1000000 0>;
+			};
+
+			led-blue {
+				active-low;
+				color = <LED_COLOR_ID_BLUE>;
+				pwms = <&led_pwm 1 1000000 0>;
+			};
+		};
+	};
+
+	led-controller-2 {
+		compatible = "gpio-leds";
+
+		led-5 {
+			label = "tac:green:iobus";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-6 {
+			label = "tac:green:can";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-7 {
+			label = "tac:green:out0";
+			gpios = <&gpiob 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-8 {
+			label = "tac:green:out1";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-9 {
+			label = "tac:green:uarttx";
+			gpios = <&gpiod 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-10 {
+			label = "tac:green:uartrx";
+			gpios = <&gpiof 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-11 {
+			label = "tac:green:usbh1";
+			gpios = <&gpioc 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-12 {
+			label = "tac:green:usbh2";
+			gpios = <&gpiod 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-13 {
+			label = "tac:green:usbh3";
+			gpios = <&gpiob 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-14 {
+			label = "tac:green:usbg";
+			gpios = <&gpiod 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-gadget";
+		};
+
+		led-15 {
+			label = "tac:green:dutpwr";
+			gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "DUT_PWR_EN", "", "STACK_CS3", /*  0 */
+	"ETH_GPIO1", "ETH_INT", "", "", "",                      /*  5 */
+	"", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP",              /* 10 */
+	"";                                                      /* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "DUT_PWR_DISCH", "", "", "", /*  0 */
+	"", "", "", "", "",                                /*  5 */
+	"", "";                                            /* 10 */
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&m_can2 {
+	termination-gpios = <&gpioe 4 GPIO_ACTIVE_HIGH>;
+	termination-ohms = <120>;
+};
+
+&spi2 {
+	adc@0 {
+		compatible = "ti,lmp92064";
+		reg = <0>;
+
+		reset-gpios = <&gpioa 4 GPIO_ACTIVE_HIGH>;
+		shunt-resistor-micro-ohms = <15000>;
+		spi-max-frequency = <5000000>;
+		vdd-supply = <&reg_pb_3v3>;
+		vdig-supply = <&reg_pb_3v3>;
+	};
+};
+
+&timers8 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	led_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm8_pins_b>;
+		pinctrl-1 = <&pwm8_sleep_pins_b>;
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..cf7485251490
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,263 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	model = "Seeed Studio Odyssey-STM32MP157C SOM";
+	compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..a8b3f7a54703
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+	model = "Seeed Studio Odyssey-STM32MP157C Board";
+	compatible = "seeed,stm32mp157c-odyssey",
+		     "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&dcmi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_b>;
+	pinctrl-1 = <&dcmi_sleep_pins_b>;
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */
+	st,eth-clk-sel;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@7 { /* KSZ9031RN */
+			reg = <7>;
+			reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-osd32mp1-red.dts b/arch/arm/boot/dts/st/stm32mp157c-osd32mp1-red.dts
new file mode 100644
index 000000000000..527c33be66cc
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-osd32mp1-red.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Geanix ApS 2023 - All Rights Reserved
+ * Author: Sean Nyekjaer <sean@geanix.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+/ {
+	model = "Octavo OSD32MP1 RED board";
+	compatible = "oct,stm32mp157c-osd32-red", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "heartbeat";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	st,eth-clk-sel;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@3 {
+			reg = <3>;
+		};
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	status = "okay";
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	hdmi-transmitter@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ltdc_pins_e>;
+		pinctrl-1 = <&ltdc_sleep_pins_e>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sii9022_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				sii9022_tx_endpoint: endpoint {
+					remote-endpoint = <&i2s2_endpoint>;
+				};
+			};
+		};
+	};
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc CK_PER>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_b>;
+	pinctrl-1 = <&i2s2_sleep_pins_b>;
+	status = "okay";
+
+	i2s2_port: port {
+		i2s2_endpoint: endpoint {
+			remote-endpoint = <&sii9022_tx_endpoint>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_d>;
+	pinctrl-1 = <&m_can1_sleep_pins_d>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbh_ohci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp1-3.dts b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp1-3.dts
new file mode 100644
index 000000000000..28d7203264ce
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp1-3.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
+ * Author: Dom VOVARD <dom.vovard@linrt.com>.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp157c-phycore-stm32mp15-som.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-STM32MP1-3 Dev Board";
+	compatible = "phytec,phycore-stm32mp1-3",
+		     "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
+
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		mmc2 = &sdmmc3;
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &usart1;
+	};
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&fmc {
+	status = "disabled";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c4_eeprom {
+	status = "okay";
+};
+
+&i2c4_rtc {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+};
+
+&sdmmc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi
new file mode 100644
index 000000000000..bf0c32027baf
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de>
+ * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
+ * Author: Dom VOVARD <dom.vovard@linrt.com>.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "stm32mp15-pinctrl.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-STM32MP15 SOM";
+	compatible = "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		rtc0 = &i2c4_rtc;
+		rtc1 = &rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-home {
+			label = "Home";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-enter {
+			label = "Enter";
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP1-PHYCORE";
+		routing =
+			"Playback", "MCLK", /* Set a route between "MCLK" and "playback" widgets */
+			"Capture", "MCLK";
+		dais = <&sai2b_port>,
+		       <&sai2a_port>;
+	};
+
+	regulator_vin: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rgmii_pins_d>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_d>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	st,eth-clk-sel;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			interrupt-parent = <&gpiog>;
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,min-output-impedance;
+			enet-phy-lane-no-swap;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+
+	codec@18 {
+		compatible = "ti,tlv320aic3007";
+		reg = <0x18>;
+		#sound-dai-cells = <0>;
+
+		ai3x-micbias-vg = <2>;
+
+		AVDD-supply = <&v3v3>;
+		IOVDD-supply = <&v3v3>;
+		DRVDD-supply = <&v3v3>;
+		DVDD-supply = <&v1v8_audio>;
+
+		clocks = <&sai2b>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tlv320_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+
+			tlv320_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+		};
+	};
+
+	touch@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		vio-supply = <&v3v3>;
+		vcc-supply = <&v3v3>;
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	leds@62 {
+		compatible = "nxp,pca9533";
+		reg = <0x62>;
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			type = <PCA9532_TYPE_LED>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	pmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&regulator_vin>;
+			buck2-supply = <&regulator_vin>;
+			buck3-supply = <&regulator_vin>;
+			buck4-supply = <&regulator_vin>;
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&regulator_vin>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			boost-supply = <&regulator_vin>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+
+			};
+
+			vdd_eth_2v5: ldo2 {
+				regulator-name = "dd_eth_2v5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			vdd_eth_1v0: ldo6 {
+				regulator-name = "vdd_eth_1v0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>,
+				     <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling",
+					  "onkey-rising";
+			power-off-time-sec = <10>;
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+		};
+	};
+
+	i2c4_eeprom: eeprom@50 {
+		compatible = "microchip,24c32",
+			     "atmel,24c32";
+		reg = <0x50>;
+	};
+
+	i2c4_rtc: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b>, <&sai2b_pins_d>;
+	pinctrl-1 = <&sai2a_sleep_pins_b>, <&sai2b_sleep_pins_d>;
+	status = "okay";
+};
+
+&sai2a {
+	dma-names = "rx";
+	st,sync = <&sai2b 2>;
+	clocks = <&rcc SAI2_K>, <&sai2b>;
+	clock-names = "sai_ck", "MCLK";
+	#clock-cells = <0>;
+
+	sai2a_port: port {
+		sai2a_endpoint: endpoint {
+			remote-endpoint = <&tlv320_rx_endpoint>;
+			mclk-fs = <256>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+	};
+};
+
+&sai2b {
+	dma-names = "tx";
+	#clock-cells = <0>;
+
+	sai2b_port: port {
+		sai2b_endpoint: endpoint {
+			remote-endpoint = <&tlv320_tx_endpoint>;
+			mclk-fs = <256>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_b>;
+	cd-gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_e>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_e>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_e>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+};
+
+&spi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi1_pins_a>;
+	pinctrl-1 = <&spi1_sleep_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	pinctrl-3 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart1 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart1_pins_b &usart1_pins_a>;
+	pinctrl-1 = <&usart1_sleep_pins_b &usart1_sleep_pins_a>;
+	pinctrl-2 = <&usart1_idle_pins_b &usart1_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_a>;
+	pinctrl-1 = <&usart3_sleep_pins_a>;
+	pinctrl-2 = <&usart3_idle_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbh_ohci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xc-lxa-tac.dtsi b/arch/arm/boot/dts/st/stm32mp15xc-lxa-tac.dtsi
new file mode 100644
index 000000000000..fc3a2386dbb9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xc-lxa-tac.dtsi
@@ -0,0 +1,603 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &port_uplink;
+		ethernet2 = &port_dut;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+		serial1 = &usart3;
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "tac:green:user1";
+			gpios = <&gpiof 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "tac:green:user2";
+			gpios = <&gpiog 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "tac:green:statusdut";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* led-3 and led-4 are internally connected antiparallel to one
+		 * another inside the ethernet jack like this:
+		 * GPIOA14 ---+---|led-3|>--+--- GPIOD15
+		 *            +--<|led-4|---+
+		 * E.g. only one of the LEDs can be illuminated at a time while
+		 * the other output must be driven low.
+		 * This should likely be implemented using a multi color LED
+		 * driver for antiparallel LEDs.
+		 */
+		led-3 {
+			label = "tac:green:statuslab";
+			gpios = <&gpioa 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "tac:orange:statuslab";
+			gpios = <&gpiod 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-lower {
+			label = "USER_BTN2";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+
+		button-upper {
+			label = "USER_BTN";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+
+	/* supplied by either barrel connector or PoE */
+	reg_12v: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_1v2: regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v>;
+	};
+
+	reg_pb_5v: regulator-pb-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_POWERBOARD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v>;
+	};
+
+	reg_pb_3v3: regulator-pb-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_POWERBOARD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_pb_5v>;
+	};
+
+	output-iobus-12v {
+		compatible = "regulator-output";
+		vout-supply = <&reg_iobus_12v>;
+	};
+
+	output-vuart {
+		compatible = "regulator-output";
+		vout-supply = <&v3v3_hdmi>;
+	};
+};
+
+baseboard_eeprom: &sip_eeprom {
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc1_ain_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,adc-channels = <0 1 2 5 9 10 13 15>;
+		st,min-sample-time-nsecs = <5000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		channel@0 {
+			reg = <0>;
+			label = "HOST_2_CURR_FB";
+		};
+
+		channel@1 {
+			reg = <1>;
+			label = "HOST_3_CURR_FB";
+		};
+
+		channel@2 {
+			reg = <2>;
+			label = "OUT_0_FB";
+		};
+
+		channel@5 {
+			reg = <5>;
+			label = "IOBUS_CURR_FB";
+		};
+
+		channel@9 {
+			reg = <9>;
+			label = "IOBUS_VOLT_FB";
+		};
+
+		channel@10 {
+			reg = <10>;
+			label = "OUT_1_FB";
+		};
+
+		channel@13 {
+			reg = <13>;
+			label = "HOST_CURR_FB";
+		};
+
+		channel@15 {
+			reg = <15>;
+			label = "HOST_1_CURR_FB";
+		};
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <12>;
+		st,min-sample-time-nsecs = <500000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		channel@12 {
+			reg = <12>;
+			label = "TEMP_INTERNAL";
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rgmii_pins_e>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_e>;
+
+	st,eth-clk-sel;
+	phy-mode = "rgmii-id";
+
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&ethernet0_rgmii_pins_e {
+	pins1 {
+		/* Reduce EMI emission by reducing RGMII drive strength */
+		slew-rate = <1>;
+	};
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "", "", /*  0 */
+	"", "USB_RESET", "", "", "",          /*  5 */
+	"", "", "", "", "",                   /* 10 */
+	"";                                   /* 15 */
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "", "TP38", /*  0 */
+	"TP39", "", "", "TP41", "TP42",           /*  5 */
+	"OLED_DC", "", "", "ETH_CS", "",          /* 10 */
+	"ETH_LAB_LEDRN";                          /* 15 */
+};
+
+&gpioe {
+	gpio-line-names = "TP35", "", "", "", "CAN_1_120R", /*  0 */
+	"", "", "USER_BTN2", "TP48", "UART_TX_EN",          /*  5 */
+	"UART_RX_EN", "TP24", "", "TP25", "TP26",           /* 10 */
+	"TP27";                                             /* 15 */
+};
+
+&gpiof {
+	gpio-line-names = "TP36", "TP37", "", "", "OLED_CS", /*  0 */
+	"", "", "", "", "",                                  /*  5 */
+	"USER_LED1", "", "STACK_CS0", "", "",                /* 10 */
+	"";                                                  /* 15 */
+};
+
+&gpiog {
+	gpio-line-names = "ETH_RESET", "", "", "", "",               /*  0 */
+	"IOBUS_FLT_FB", "", "USER_LED2", "ETH1_PPS_A", "CAN_0_120R", /*  5 */
+	"TP49", "", "", "", "",                                      /* 10 */
+	"";                                                          /* 15 */
+};
+
+&gpioh {
+	gpio-line-names = "", "", "OUT_1", "OUT_0", "OLED_RESET", /*  0 */
+	"", "", "", "", "",                                       /*  5 */
+	"ETH1_PPS_B", "ETH_GPIO2", "", "IOBUS_PWR_EN", "",        /* 10 */
+	"TP33";                                                   /* 15 */
+};
+
+&gpioi {
+	gpio-line-names = "TIM_RTS", "", "", "", "DEVICE_DATA_EN", /*  0 */
+	"", "", "", "ETH_WOL", "TP43",                             /*  5 */
+	"", "USER_BTN";                                            /* 10 */
+};
+
+&gpioz {
+	gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /*  0 */
+	"", "HWID4", "HWID5";                                     /*  5 */
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	status = "okay";
+
+	powerboard_eeprom: eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		vcc-supply = <&v3v3>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+		status = "disabled";
+	};
+};
+
+&i2c5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_b>;
+	pinctrl-1 = <&i2c5_sleep_pins_b>;
+
+	status = "okay";
+
+	usbhub: usbhub@2c {
+		compatible ="microchip,usb2514b";
+		reg = <0x2c>;
+		vdd-supply = <&v3v3>;
+		reset-gpios = <&gpiob 6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <8>;
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
+
+&pmic {
+	regulators {
+		buck1-supply = <&reg_5v>;	/* VIN */
+		buck2-supply = <&reg_5v>;	/* VIN */
+		buck3-supply = <&reg_5v>;	/* VIN */
+		buck4-supply = <&reg_5v>;	/* VIN */
+		ldo2-supply = <&reg_5v>;	/* PMIC_LDO25IN */
+		ldo4-supply = <&reg_5v>;	/* VIN */
+		ldo5-supply = <&reg_5v>;	/* PMIC_LDO25IN */
+		vref_ddr-supply = <&reg_5v>;	/* VIN */
+		boost-supply = <&reg_5v>;	/* PMIC_BSTIN */
+		pwr_sw2-supply = <&bst_out>;	/* PMIC_SWIN */
+	};
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+	vmmc-supply = <&v3v3>;
+
+	bus-width = <8>;
+	mmc-ddr-3_3v;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+
+	status = "okay";
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_c>;
+	cs-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&spi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi4_pins_a>;
+	cs-gpios = <&gpiof 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	lcd: display@0 {
+		compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
+		reg = <0>;
+		power-supply = <&v3v3>;
+		io-supply = <&v3v3>;
+		backlight = <&backlight>;
+		dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
+		spi-3wire;
+		spi-max-frequency = <32000000>;
+
+		width-mm = <23>;
+		height-mm = <23>;
+		rotation = <180>;
+
+		panel-timing {
+			hactive = <240>;
+			vactive = <240>;
+			hback-porch = <0>;
+			vback-porch = <0>;
+
+			clock-frequency = <0>;
+			hfront-porch = <0>;
+			hsync-len = <0>;
+			vfront-porch = <0>;
+			vsync-len = <0>;
+		};
+	};
+};
+
+&spi5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi5_pins_a>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	cs-gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+
+	switch: switch@0 {
+		compatible = "microchip,ksz9563";
+		reg = <0>;
+
+		reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <44000000>;
+
+		interrupt-parent = <&gpioa>;
+		interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port_dut: port@0 {
+				reg = <0>;
+				label = "dut";
+			};
+
+			port_uplink: port@1 {
+				reg = <1>;
+				label = "uplink";
+			};
+
+			port_cpu: port@2 {
+				reg = <2>;
+				label = "cpu";
+
+				ethernet = <&ethernet0>;
+
+				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <2000>;
+				tx-internal-delay-ps = <2000>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	label = "debug";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+};
+
+&usart3 {
+	label = "dut";
+	uart-has-rtscts;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_f>;
+
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+
+	vusb_d-supply = <&vdd_usb>;
+	vusb_a-supply = <&reg18>;
+
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdda>;
+
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xc.dtsi b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
new file mode 100644
index 000000000000..b06a55a2fa18
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/ {
+	soc {
+		cryp1: cryp@54001000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54001000 0x400>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-drc02.dtsi
new file mode 100644
index 000000000000..bb4f8a0b937f
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-drc02.dtsi
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&gpiob {
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the STM32 UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <8 0>;
+		output-low;
+		line-name = "rs485-rx-en";
+	};
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DRC02-Out1",
+			  "DRC02-Out2", "", "", "";
+};
+
+&gpioi {
+	gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "DRC02-In2", "", "", "",
+			  "", "", "", "";
+
+	/*
+	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
+	 * pulled high in order to be detected by the USB Controller.
+	 * This signal should be handled by USB power sequencing in
+	 * order to reset the Hub when USB bus is powered down, but
+	 * so far there is no such functionality.
+	 */
+	usb-hub-hog {
+		gpio-hog;
+		gpios = <2 0>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c4 {
+	touchscreen@49 {
+		status = "disabled";
+	};
+};
+
+&i2c5 {	/* TP7/TP8 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc3 {
+	/*
+	 * On DRC02, the SoM does not have SDIO WiFi. The pins
+	 * are used for on-board microSD slot instead.
+	 */
+	/delete-property/broken-cd;
+	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	/* Use PIO for the display */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";	/* Enable once there is display driver */
+	/*
+	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
+	 * also connected to the display board connector.
+	 */
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/*
+ * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
+ *       however the STM32MP1 pinmux cannot map them to UART4 .
+ */
+
+&uart8 {	/* RS485 */
+	linux,rs485-enabled-at-boot-time;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-pdk2.dtsi
new file mode 100644
index 000000000000..466d9701add0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-pdk2.dtsi
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 3 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_panel_bl>;
+		status = "okay";
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		/*
+		 * The EXTi IRQ line 3 is shared with ethernet,
+		 * so mark this as polled GPIO key.
+		 */
+		button-0 {
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 6 is shared with touchscreen,
+		 * so mark this as polled GPIO key.
+		 */
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 0 is shared with PMIC,
+		 * so mark this as polled GPIO key.
+		 */
+		button-2 {
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-3 {
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "green:led5";
+			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "disabled";
+		};
+
+		led-1 {
+			label = "green:led6";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "green:led7";
+			gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "green:led8";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+		power-supply = <&reg_panel_bl>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_panel_bl: regulator-panel-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_backlight";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_panel_supply>;
+	};
+
+	reg_panel_supply: regulator-panel-supply {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_supply";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		widgets = "Headphone", "Headphone Jack",
+			  "Line", "Line In Jack",
+			  "Microphone", "Microphone Jack";
+		routing = "Headphone Jack", "HP_OUT",
+			  "LINE_IN", "Line In Jack",
+			  "MIC_IN", "Microphone Jack",
+			  "Microphone Jack", "Mic Bias";
+		dais = <&sai2a_port &sai2b_port>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {	/* Header X22 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&i2c5 {	/* Header X21 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&v3v3>;
+		VDDIO-supply = <&vdd>;
+
+		sgtl5000_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sgtl5000_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&sgtl5000_tx_endpoint>;
+				bitclock-master = <&sgtl5000_tx_endpoint>;
+			};
+
+			sgtl5000_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&sgtl5000_rx_endpoint>;
+				bitclock-master = <&sgtl5000_rx_endpoint>;
+			};
+		};
+
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-1 = <&ltdc_sleep_pins_b>;
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_tx_endpoint>;
+				dai-format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_rx_endpoint>;
+				dai-format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+	pwm2: pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-picoitx.dtsi
new file mode 100644
index 000000000000..b5bc53accd6b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-picoitx.dtsi
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "yellow:led";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&fmc {
+	status = "disabled";
+};
+
+&gpioa {
+	/*
+	 * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
+	 * port power. This signal should be handled by USB power sequencing
+	 * in order to turn on port power when USB bus is powered up, but so
+	 * far there is no such functionality.
+	 */
+	usb-port-power-hog {
+		gpio-hog;
+		gpios = <13 0>;
+		output-low;
+		line-name = "usb-port-power";
+	};
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "PicoITX-In1", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "PicoITX-Out1",
+			  "PicoITX-Out2", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "PicoITX-In2", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c2 {	/* On board-to-board connector (optional) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c5 {	/* On board-to-board connector */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ksz8851 {
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbh_ohci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi
new file mode 100644
index 000000000000..74a11ccc5333
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+};
+
+&adc1 {
+	channel@0 {
+		reg = <0>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&adc2 {
+	channel@1 {
+		reg = <1>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_c &mco2_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_c &mco2_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+			/* LAN8710Ai */
+			compatible = "ethernet-phy-id0007.c0f0",
+				     "ethernet-phy-ieee802.3-c22";
+			clocks = <&rcc CK_MCO2>;
+			reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			smsc,disable-energy-detect;
+			interrupt-parent = <&gpioi>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-K", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-Q", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-E", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DHCOM-F",
+			  "DHCOM-D", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-P", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "DHCOM-A",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "DHCOM-C", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DHCOM-N",
+			  "DHCOM-J", "DHCOM-W", "DHCOM-V", "DHCOM-U",
+			  "DHCOM-T", "", "DHCOM-S", "";
+};
+
+&gpioi {
+	gpio-line-names = "DHCOM-G", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-always-on;
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	touchscreen@49 {
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&v3v3>;
+		interrupts-extended = <&gpioh 15 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rcc {
+	/* Connect MCO2 output to ETH_RX_CLK input via pad-pad connection */
+	clocks = <&rcc CK_MCO2>;
+	clock-names = "ETH_RX_CLK/ETH_REF_CLK";
+
+	/*
+	 * Set PLL4P output to 100 MHz to supply SDMMC with faster clock,
+	 * set MCO2 output to 50 MHz to supply ETHRX clock with PLL4P/2,
+	 * so that MCO2 behaves as a divider for the ETHRX clock here.
+	 */
+	assigned-clocks = <&rcc CK_MCO2>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <50000000>, <100000000>;
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep", "init";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>;
+	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	st,cmd-gpios = <&gpiod 2 0>;
+	st,ck-gpios = <&gpioc 12 0>;
+	st,ckin-gpios = <&gpioe 4 0>;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc1_b4_pins_a {
+	/*
+	 * SD bus pull-up resistors:
+	 * - optional on SoMs with SD voltage translator
+	 * - mandatory on SoMs without SD voltage translator
+	 */
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-avenger96.dtsi
new file mode 100644
index 000000000000..343a4613dfca
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-avenger96.dtsi
@@ -0,0 +1,514 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
+#include "stm32mp15xx-dhcor-io1v8.dtsi"
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		serial0 = &uart4;
+		serial1 = &uart7;
+		serial2 = &usart2;
+		spi0 = &qspi;
+	};
+
+	/* XTal Q1 */
+	cec_clock: clk-cec-fixed {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7513_out>;
+			};
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "green:user0";
+			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:user1";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "green:user2";
+			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "green:user3";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32-AV96-HDMI";
+		dais = <&sai2a_port>;
+		status = "okay";
+	};
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+};
+
+&adc1 {
+	channel@0 {
+		reg = <0>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@1 {
+		reg = <1>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@6 {
+		reg = <6>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&adc2 {
+	channel@0 {
+		reg = <0>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@1 {
+		reg = <1>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@2 {
+		reg = <2>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&dcmi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_c>;
+	pinctrl-1 = <&dcmi_sleep_pins_c>;
+	status = "disabled";
+
+	port {
+		dcmi_0: endpoint {
+			remote-endpoint = <&stmipi_2>;
+			bus-type = <5>;
+			bus-width = <8>;
+			pclk-sample = <0>;
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "AV96-K",
+			  "AV96-I", "", "AV96-A", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "AV96-J", "", "",
+			  "", "", "", "AV96-B",
+			  "", "AV96-L", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "AV96-C",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "AV96-D", "", "", "",
+			  "", "", "AV96-E", "AV96-F";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "AV96-G", "AV96-H", "", "";
+};
+
+&i2c1 {	/* X6 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c2 {	/* X6 I2C2 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_c>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	stmipi: stmipi@14 {
+		compatible = "st,st-mipid02";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&mco1_pins_a>;
+		pinctrl-1 = <&mco1_sleep_pins_a>;
+		reg = <0x14>;
+		clocks = <&rcc CK_MCO1>;
+		clock-names = "xclk";
+		assigned-clocks = <&rcc CK_MCO1>;
+		assigned-clock-parents = <&rcc CK_HSE>;
+		assigned-clock-rates = <24000000>;
+		VDDE-supply = <&v1v8>;
+		VDDIN-supply = <&v1v8>;
+		reset-gpios = <&gpioz 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stmipi_0: endpoint {
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				stmipi_2: endpoint {
+					bus-width = <8>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+					pclk-sample = <0>;
+					remote-endpoint = <&dcmi_0>;
+				};
+			};
+		};
+	};
+
+	hdmi-transmitter@3d {
+		compatible = "adi,adv7513";
+		reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
+		reg-names = "main", "edid", "cec", "packet";
+		clocks = <&cec_clock>;
+		clock-names = "cec";
+
+		avdd-supply = <&v3v3>;
+		dvdd-supply = <&v3v3>;
+		pvdd-supply = <&v3v3>;
+		dvdd-3v-supply = <&v3v3>;
+		bgvdd-supply = <&v3v3>;
+
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+
+		status = "okay";
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7513_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7513_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				adv7513_i2s0: endpoint {
+					remote-endpoint = <&sai2a_endpoint>;
+				};
+			};
+		};
+	};
+
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_d>;
+	pinctrl-1 = <&ltdc_sleep_pins_d>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&adv7513_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_c>;
+	pinctrl-1 = <&sai2a_sleep_pins_c>;
+	clock-names = "pclk", "x8k", "x11k";
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&adv7513_i2s0>;
+				dai-format = "i2s";
+				mclk-fs = <256>;
+			};
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd_io>;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	/* On Low speed expansion header */
+	label = "LS-UART1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	/* On Low speed expansion header */
+	label = "LS-UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* Bluetooth */
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	status = "okay";
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-drc-compact.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-drc-compact.dtsi
new file mode 100644
index 000000000000..bc4ddcbdd5cf
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-drc-compact.dtsi
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		mmc0 = &sdmmc1;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+		serial0 = &uart4;
+		serial1 = &uart8;
+		serial2 = &usart3;
+		serial3 = &uart5;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "yellow:user0";
+			gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "red:user1";
+			gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {	/* X11 ADC inputs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+
+	adc2: adc@100 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@2 {
+			reg = <2>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "DRCC-VAR2", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "DRCC-GPIO0", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "DRCC-GPIO5", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "DRCC-HW2",
+			  "DRCC-GPIO4", "", "", "",
+			  "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
+			  "DRCC-VAR0", "", "", "DRCC-GPIO6";
+};
+
+&gpioi {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DRCC-GPIO2",
+			  "", "DRCC-GPIO1", "", "",
+			  "", "", "", "";
+};
+
+&i2c1 {	/* X11 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {	/* MicroSD */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc2 {	/* eMMC */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc3 {	/* SDIO Wi-Fi */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	bus-width = <4>;
+	mmc-ddr-3_3v;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi2 {	/* X11 SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_b>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	label = "UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_d>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart5 {	/* X11 UART */
+	label = "X11-UART5";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	label = "RS485-1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart3 {	/* RS485 or RS232 */
+	label = "RS485-2";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart3_pins_e>;
+	pinctrl-1 = <&usart3_sleep_pins_e>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbh_ohci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-io1v8.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-io1v8.dtsi
new file mode 100644
index 000000000000..9937b28548c2
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-io1v8.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
+	vdd_io: regulator-buck-io {
+		compatible = "regulator-fixed";
+		regulator-name = "buck-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&vdd {
+	regulator-min-microvolt = <2900000>;
+	regulator-max-microvolt = <2900000>;
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd_io>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi
new file mode 100644
index 000000000000..89881a26c614
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		spi0 = &qspi;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				regulator-enable-ramp-delay = <300000>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-testbench.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-testbench.dtsi
new file mode 100644
index 000000000000..6e79c4b6fe32
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-testbench.dtsi
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+		serial1 = &uart7;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+
+	adc2: adc@100 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@2 {
+			reg = <2>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&i2c4 {
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	status = "okay";
+};
+
+&usbh_ohci {
+	status = "okay";
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	status = "okay";
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157a-dk1.dts b/arch/arm/boot/dts/st/stm32mp15xx-dkx.dtsi
index 984a47cbd13d..f7634c51efb2 100644
--- a/arch/arm/boot/dts/stm32mp157a-dk1.dts
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dkx.dtsi
@@ -4,24 +4,14 @@
  * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
  */
 
-/dts-v1/;
-
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xac-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/mfd/st,stpmic1.h>
 
 / {
-	model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
-	compatible = "st,stm32mp157a-dk1", "st,stm32mp157";
-
 	aliases {
-		ethernet0 = &ethernet0;
 		serial0 = &uart4;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
+		serial1 = &usart3;
+		serial2 = &uart7;
 	};
 
 	memory@c0000000 {
@@ -69,16 +59,11 @@
 			reg = <0x38000000 0x10000>;
 			no-map;
 		};
-
-		gpu_reserved: gpu@d4000000 {
-			reg = <0xd4000000 0x4000000>;
-			no-map;
-		};
 	};
 
 	led {
 		compatible = "gpio-leds";
-		blue {
+		led-blue {
 			label = "heartbeat";
 			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -88,7 +73,7 @@
 
 	sound {
 		compatible = "audio-graph-card";
-		label = "STM32MP1-DK";
+		label = "STM32MP15-DK";
 		routing =
 			"Playback" , "MCLK",
 			"Capture" , "MCLK",
@@ -96,52 +81,79 @@
 		dais = <&sai2a_port &sai2b_port &i2s2_port>;
 		status = "okay";
 	};
+
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 };
 
 &adc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
+	pinctrl-0 = <&adc12_usb_cc_pins_a>;
 	vdd-supply = <&vdd>;
 	vdda-supply = <&vdd>;
 	vref-supply = <&vrefbuf>;
-	status = "disabled";
+	status = "okay";
 	adc1: adc@0 {
+		status = "okay";
 		/*
 		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
 		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
 		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
 		 * Use arbitrary margin here (e.g. 5us).
 		 */
-		st,min-sample-time-nsecs = <5000>;
-		/* AIN connector, USB Type-C CC1 & CC2 */
-		st,adc-channels = <0 1 6 13 18 19>;
-		status = "okay";
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
 	};
 	adc2: adc@100 {
-		/* AIN connector, USB Type-C CC1 & CC2 */
-		st,adc-channels = <0 1 2 6 18 19>;
-		st,min-sample-time-nsecs = <5000>;
 		status = "okay";
+		/* USB Type-C CC1 & CC2 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
 	};
 };
 
 &cec {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cec_pins_b>;
-	pinctrl-1 = <&cec_pins_sleep_b>;
+	pinctrl-1 = <&cec_sleep_pins_b>;
+	status = "okay";
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dts {
 	status = "okay";
 };
 
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rgmii-id";
 	max-speed = <1000>;
 	phy-handle = <&phy0>;
 
-	mdio0 {
+	mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "snps,dwmac-mdio";
@@ -151,15 +163,14 @@
 	};
 };
 
-&gpu {
-	contiguous-area = <&gpu_reserved>;
+&hash1 {
 	status = "okay";
 };
 
 &i2c1 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c1_pins_a>;
-	pinctrl-1 = <&i2c1_pins_sleep_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
 	i2c-scl-rising-time-ns = <100>;
 	i2c-scl-falling-time-ns = <7>;
 	status = "okay";
@@ -217,30 +228,56 @@
 			cs42l51_tx_endpoint: endpoint@0 {
 				reg = <0>;
 				remote-endpoint = <&sai2a_endpoint>;
-				frame-master;
-				bitclock-master;
+				frame-master = <&cs42l51_tx_endpoint>;
+				bitclock-master = <&cs42l51_tx_endpoint>;
 			};
 
 			cs42l51_rx_endpoint: endpoint@1 {
 				reg = <1>;
 				remote-endpoint = <&sai2b_endpoint>;
-				frame-master;
-				bitclock-master;
+				frame-master = <&cs42l51_rx_endpoint>;
+				bitclock-master = <&cs42l51_rx_endpoint>;
 			};
 		};
 	};
 };
 
 &i2c4 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
 	i2c-scl-rising-time-ns = <185>;
 	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
 	status = "okay";
 	/* spare dmas for other usage */
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
+	stusb1600@28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+		status = "okay";
+		vdd-supply = <&vin>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			typec-power-opmode = "default";
+
+			port {
+				con_usbotg_hs_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
@@ -251,9 +288,18 @@
 
 		regulators {
 			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&vin>;
+			buck2-supply = <&vin>;
+			buck3-supply = <&vin>;
+			buck4-supply = <&vin>;
 			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&vin>;
 			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&vin>;
+			ldo5-supply = <&vin>;
 			ldo6-supply = <&v3v3>;
+			vref_ddr-supply = <&vin>;
+			boost-supply = <&vin>;
 			pwr_sw1-supply = <&bst_out>;
 			pwr_sw2-supply = <&bst_out>;
 
@@ -320,8 +366,6 @@
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -344,24 +388,23 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
-			 bst_out: boost {
+			bst_out: boost {
 				regulator-name = "bst_out";
 				interrupts = <IT_OCP_BOOST 0>;
-			 };
+			};
 
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-			 };
+			};
 
-			 vbus_sw: pwr_sw2 {
+			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
 				regulator-active-discharge = <1>;
-			 };
+			};
 		};
 
 		onkey {
@@ -379,18 +422,31 @@
 	};
 };
 
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
 &i2s2 {
 	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
 	clock-names = "pclk", "i2sclk", "x8k", "x11k";
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2s2_pins_a>;
-	pinctrl-1 = <&i2s2_pins_sleep_a>;
+	pinctrl-1 = <&i2s2_sleep_pins_a>;
 	status = "okay";
 
 	i2s2_port: port {
 		i2s2_endpoint: endpoint {
 			remote-endpoint = <&sii9022_tx_endpoint>;
-			format = "i2s";
+			dai-format = "i2s";
 			mclk-fs = <256>;
 		};
 	};
@@ -408,15 +464,11 @@
 &ltdc {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&ltdc_pins_a>;
-	pinctrl-1 = <&ltdc_pins_sleep_a>;
+	pinctrl-1 = <&ltdc_sleep_pins_a>;
 	status = "okay";
 
 	port {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ltdc_ep0_out: endpoint@0 {
-			reg = <0>;
+		ltdc_ep0_out: endpoint {
 			remote-endpoint = <&sii9022_in>;
 		};
 	};
@@ -425,8 +477,8 @@
 &m4_rproc {
 	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
 			<&vdev0vring1>, <&vdev0buffer>;
-	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
-	mbox-names = "vq0", "vq1", "shutdown";
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
 	interrupt-parent = <&exti>;
 	interrupts = <68 1>;
 	status = "okay";
@@ -456,14 +508,12 @@
 	sai2a: audio-controller@4400b004 {
 		#clock-cells = <0>;
 		dma-names = "tx";
-		clocks = <&rcc SAI2_K>;
-		clock-names = "sai_ck";
 		status = "okay";
 
 		sai2a_port: port {
 			sai2a_endpoint: endpoint {
 				remote-endpoint = <&cs42l51_tx_endpoint>;
-				format = "i2s";
+				dai-format = "i2s";
 				mclk-fs = <256>;
 				dai-tdm-slot-num = <2>;
 				dai-tdm-slot-width = <32>;
@@ -481,7 +531,7 @@
 		sai2b_port: port {
 			sai2b_endpoint: endpoint {
 				remote-endpoint = <&cs42l51_rx_endpoint>;
-				format = "i2s";
+				dai-format = "i2s";
 				mclk-fs = <256>;
 				dai-tdm-slot-num = <2>;
 				dai-tdm-slot-width = <32>;
@@ -495,19 +545,193 @@
 	pinctrl-0 = <&sdmmc1_b4_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
-	broken-cd;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
 	st,neg-edge;
 	bus-width = <4>;
 	vmmc-supply = <&v3v3>;
 	status = "okay";
 };
 
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "disabled";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer@5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
 &uart4 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep", "idle";
 	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
+&uart7 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart7_pins_c>;
+	pinctrl-1 = <&uart7_sleep_pins_c>;
+	pinctrl-2 = <&uart7_idle_pins_c>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_c>;
+	pinctrl-1 = <&usart3_sleep_pins_c>;
+	pinctrl-2 = <&usart3_idle_pins_c>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbh_ehci {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&v3v3>;
+	};
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usbotg_hs_ep>;
+		};
+	};
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
 &vrefbuf {
 	regulator-min-microvolt = <2500000>;
 	regulator-max-microvolt = <2500000>;
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-osd32.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-osd32.dtsi
new file mode 100644
index 000000000000..aeb71c41a734
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-osd32.dtsi
@@ -0,0 +1,216 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+		};
+
+		pmic_watchdog: watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	sip_eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		vcc-supply = <&vdd>;
+		reg = <0x50>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxaa-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxaa-pinctrl.dtsi
new file mode 100644
index 000000000000..04f7a43ad66f
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxaa-pinctrl.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AA>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@5000a000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@5000b000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@5000c000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
+
+&pinctrl_z {
+	st,package = <STM32MP_PKG_AA>;
+
+	gpioz: gpio@54004000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl_z 0 400 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxab-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxab-pinctrl.dtsi
new file mode 100644
index 000000000000..328dad140e9b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxab-pinctrl.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AB>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <6>;
+		gpio-ranges = <&pinctrl 6 86 6>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl 6 102 10>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <2>;
+		gpio-ranges = <&pinctrl 0 112 2>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxac-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxac-pinctrl.dtsi
new file mode 100644
index 000000000000..7eaa245f44db
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxac-pinctrl.dtsi
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AC>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@5000a000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 0 128 12>;
+	};
+};
+
+&pinctrl_z {
+	st,package = <STM32MP_PKG_AC>;
+
+	gpioz: gpio@54004000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl_z 0 400 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxad-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxad-pinctrl.dtsi
new file mode 100644
index 000000000000..b63e207de216
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxad-pinctrl.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AD>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <6>;
+		gpio-ranges = <&pinctrl 6 86 6>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl 6 102 10>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <2>;
+		gpio-ranges = <&pinctrl 0 112 2>;
+	};
+};
diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
deleted file mode 100644
index 55fff4d44277..000000000000
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ /dev/null
@@ -1,228 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Linaro Ltd
- */
-
-#include <dt-bindings/clock/ste-ab8500.h>
-
-/ {
-	soc {
-		prcmu@80157000 {
-			ab8500 {
-				compatible = "stericsson,ab8500";
-				interrupt-parent = <&intc>;
-				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-
-				ab8500_clock: clock-controller {
-					compatible = "stericsson,ab8500-clk";
-					#clock-cells = <1>;
-				};
-
-				ab8500_gpio: ab8500-gpio {
-					compatible = "stericsson,ab8500-gpio";
-					gpio-controller;
-					#gpio-cells = <2>;
-				};
-
-				ab8500-rtc {
-					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "60S", "ALARM";
-				};
-
-				ab8500-gpadc {
-					compatible = "stericsson,ab8500-gpadc";
-					interrupts = <32 IRQ_TYPE_LEVEL_HIGH
-						      39 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "HW_CONV_END", "SW_CONV_END";
-					vddadc-supply = <&ab8500_ldo_tvout_reg>;
-				};
-
-				ab8500_battery: ab8500_battery {
-					stericsson,battery-type = "LIPO";
-					thermistor-on-batctrl;
-				};
-
-				ab8500_fg {
-					compatible = "stericsson,ab8500-fg";
-					battery	   = <&ab8500_battery>;
-				};
-
-				ab8500_btemp {
-					compatible = "stericsson,ab8500-btemp";
-					battery	   = <&ab8500_battery>;
-				};
-
-				ab8500_charger {
-					compatible	= "stericsson,ab8500-charger";
-					battery		= <&ab8500_battery>;
-					vddadc-supply	= <&ab8500_ldo_tvout_reg>;
-				};
-
-				ab8500_chargalg {
-					compatible	= "stericsson,ab8500-chargalg";
-					battery		= <&ab8500_battery>;
-				};
-
-				ab8500_usb {
-					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "ID_WAKEUP_R",
-							  "ID_WAKEUP_F",
-							  "VBUS_DET_F",
-							  "VBUS_DET_R",
-							  "USB_LINK_STATUS",
-							  "USB_ADP_PROBE_PLUG",
-							  "USB_ADP_PROBE_UNPLUG";
-					vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
-					v-ape-supply = <&db8500_vape_reg>;
-					musb_1v8-supply = <&db8500_vsmps2_reg>;
-					clocks = <&prcmu_clk PRCMU_SYSCLK>;
-					clock-names = "sysclk";
-				};
-
-				ab8500-ponkey {
-					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
-				};
-
-				ab8500-sysctrl {
-					compatible = "stericsson,ab8500-sysctrl";
-				};
-
-				ab8500-pwm {
-					compatible = "stericsson,ab8500-pwm";
-					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
-					clock-names = "intclk";
-				};
-
-				ab8500-debugfs {
-					compatible = "stericsson,ab8500-debug";
-				};
-
-				codec: ab8500-codec {
-					compatible = "stericsson,ab8500-codec";
-
-					V-AUD-supply = <&ab8500_ldo_audio_reg>;
-					V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
-					V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
-					V-DMIC-supply = <&ab8500_ldo_dmic_reg>;
-
-					clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
-					clock-names = "audioclk";
-
-					stericsson,earpeice-cmv = <950>; /* Units in mV. */
-				};
-
-				ext_regulators: ab8500-ext-regulators {
-					compatible = "stericsson,ab8500-ext-regulator";
-
-					ab8500_ext1_reg: ab8500_ext1 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-boot-on;
-						regulator-always-on;
-					};
-
-					ab8500_ext2_reg: ab8500_ext2 {
-						regulator-min-microvolt = <1360000>;
-						regulator-max-microvolt = <1360000>;
-						regulator-boot-on;
-						regulator-always-on;
-					};
-
-					ab8500_ext3_reg: ab8500_ext3 {
-						regulator-min-microvolt = <3400000>;
-						regulator-max-microvolt = <3400000>;
-						regulator-boot-on;
-					};
-				};
-
-				ab8500-regulators {
-					compatible = "stericsson,ab8500-regulator";
-					vin-supply = <&ab8500_ext3_reg>;
-
-					// supplies to the display/camera
-					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
-						regulator-min-microvolt = <2500000>;
-						regulator-max-microvolt = <2900000>;
-						regulator-boot-on;
-						/* BUG: If turned off MMC will be affected. */
-						regulator-always-on;
-					};
-
-					// supplies to the on-board eMMC
-					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
-						regulator-min-microvolt = <1100000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					// supply for VAUX3; SDcard slots
-					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
-						regulator-min-microvolt = <1100000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					// supply for v-intcore12; VINTCORE12 LDO
-					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
-					};
-
-					// supply for tvout; gpadc; TVOUT LDO
-					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
-					};
-
-					// supply for ab8500-vaudio; VAUDIO LDO
-					ab8500_ldo_audio_reg: ab8500_ldo_audio {
-					};
-
-					// supply for v-anamic1 VAMIC1 LDO
-					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
-					};
-
-					// supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
-					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
-					};
-
-					// supply for v-dmic; VDMIC LDO
-					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
-					};
-
-					// supply for U8500 CSI/DSI; VANA LDO
-					ab8500_ldo_ana_reg: ab8500_ldo_ana {
-					};
-				};
-			};
-		};
-
-		sound {
-			stericsson,audio-codec = <&codec>;
-			clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
-			clock-names = "sysclk", "ulpclk", "intclk";
-		};
-
-		mcde@a0350000 {
-			vana-supply = <&ab8500_ldo_ana_reg>;
-
-			dsi@a0351000 {
-				vana-supply = <&ab8500_ldo_ana_reg>;
-			};
-			dsi@a0352000 {
-				vana-supply = <&ab8500_ldo_ana_reg>;
-			};
-			dsi@a0353000 {
-				vana-supply = <&ab8500_ldo_ana_reg>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ste-href-ab8505.dtsi b/arch/arm/boot/dts/ste-href-ab8505.dtsi
deleted file mode 100644
index 95cf38a008e9..000000000000
--- a/arch/arm/boot/dts/ste-href-ab8505.dtsi
+++ /dev/null
@@ -1,234 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2014 Linaro Ltd.
- */
-
-/ {
-	soc {
-		prcmu@80157000 {
-			ab8505 {
-				ab8505-gpio {
-					/* Hog a few default settings */
-					pinctrl-names = "default";
-					pinctrl-0 = <&gpio2_default_mode>,
-						    <&gpio10_default_mode>,
-						    <&gpio11_default_mode>,
-						    <&gpio13_default_mode>,
-						    <&gpio34_default_mode>,
-						    <&gpio50_default_mode>,
-						    <&pwm_default_mode>,
-						    <&adi2_default_mode>,
-						    <&modsclsda_default_mode>,
-						    <&resethw_default_mode>,
-						    <&service_default_mode>;
-
-					/*
-					 * Pins 2, 10, 11, 13, 34 and 50
-					 * are muxed in as GPIO, and configured as INPUT PULL DOWN
-					 */
-					gpio2 {
-						gpio2_default_mode: gpio2_default {
-							default_mux {
-								function = "gpio";
-								groups = "gpio2_a_1";
-							};
-							default_cfg {
-								pins = "GPIO2_R5";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					gpio10 {
-						gpio10_default_mode: gpio10_default {
-							default_mux {
-								function = "gpio";
-								groups = "gpio10_d_1";
-							};
-							default_cfg {
-								pins = "GPIO10_B16";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					gpio11 {
-						gpio11_default_mode: gpio11_default {
-							default_mux {
-								function = "gpio";
-								groups = "gpio11_d_1";
-							};
-							default_cfg {
-								pins = "GPIO11_B17";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					gpio13 {
-						gpio13_default_mode: gpio13_default {
-							default_mux {
-								function = "gpio";
-								groups = "gpio13_d_1";
-							};
-							default_cfg {
-								pins = "GPIO13_D17";
-								input-enable;
-								bias-disable;
-							};
-						};
-					};
-					gpio34 {
-						gpio34_default_mode: gpio34_default {
-							default_mux {
-								function = "gpio";
-								groups = "gpio34_a_1";
-							};
-							default_cfg {
-								pins = "GPIO34_H14";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					gpio50 {
-						gpio50_default_mode: gpio50_default {
-							default_mux {
-								function = "gpio";
-								groups = "gpio50_d_1";
-							};
-							default_cfg {
-								pins = "GPIO50_L4";
-								input-enable;
-								bias-disable;
-							};
-						};
-					};
-					/* This sets up the PWM pin 14 */
-					pwm {
-						pwm_default_mode: pwm_default {
-							default_mux {
-								function = "pwmout";
-								groups = "pwmout1_d_1";
-							};
-							default_cfg {
-								pins = "GPIO14_C16";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					/* This sets up audio interface 2 */
-					adi2 {
-						adi2_default_mode: adi2_default {
-							default_mux {
-								function = "adi2";
-								groups = "adi2_d_1";
-							};
-							default_cfg {
-								pins = "GPIO17_P2",
-									 "GPIO18_N3",
-									 "GPIO19_T1",
-									 "GPIO20_P3";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					/* Modem I2C setup (SCL and SDA pins) */
-					modsclsda {
-						modsclsda_default_mode: modsclsda_default {
-							default_mux {
-								function = "modsclsda";
-								groups = "modsclsda_d_1";
-							};
-							default_cfg {
-								pins = "GPIO40_J15",
-									"GPIO41_J14";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					resethw {
-						resethw_default_mode: resethw_default {
-							default_mux {
-								function = "resethw";
-								groups = "resethw_d_1";
-							};
-							default_cfg {
-								pins = "GPIO52_D16";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					service {
-						service_default_mode: service_default {
-							default_mux {
-								function = "service";
-								groups = "service_d_1";
-							};
-							default_cfg {
-								pins = "GPIO53_D15";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					/*
-					 * Clock output pins associated with regulators.
-					 */
-					sysclkreq2 {
-						sysclkreq2_default_mode: sysclkreq2_default {
-							default_mux {
-								function = "sysclkreq";
-								groups = "sysclkreq2_d_1";
-							};
-							default_cfg {
-								pins = "GPIO1_N4";
-								input-enable;
-								bias-disable;
-							};
-						};
-						sysclkreq2_sleep_mode: sysclkreq2_sleep {
-							default_mux {
-								function = "gpio";
-								groups = "gpio1_a_1";
-							};
-							default_cfg {
-								pins = "GPIO1_N4";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-					sysclkreq4 {
-						sysclkreq4_default_mode: sysclkreq4_default {
-							default_mux {
-								function = "sysclkreq";
-								groups = "sysclkreq4_d_1";
-							};
-							default_cfg {
-								pins = "GPIO3_P5";
-								input-enable;
-								bias-disable;
-							};
-						};
-						sysclkreq4_sleep_mode: sysclkreq4_sleep {
-							default_mux {
-								function = "gpio";
-								groups = "gpio3_a_1";
-							};
-							default_cfg {
-								pins = "GPIO3_P5";
-								input-enable;
-								bias-pull-down;
-							};
-						};
-					};
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
deleted file mode 100644
index 2c382d274ff6..000000000000
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ /dev/null
@@ -1,742 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Linaro Ltd.
- */
-
-#include "ste-nomadik-pinctrl.dtsi"
-
-/ {
-	soc {
-		pinctrl {
-			/* Settings for all UART default and sleep states */
-			uart0 {
-				uart0_default_mode: uart0_default {
-					default_mux {
-						function = "u0";
-						groups = "u0_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
-						ste,config = <&in_pu>;
-					};
-
-					default_cfg2 {
-						pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
-						ste,config = <&out_hi>;
-					};
-				};
-
-				uart0_sleep_mode: uart0_sleep {
-					sleep_cfg1 {
-						pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-
-					sleep_cfg2 {
-						pins = "GPIO1_AJ3"; /* RTS */
-						ste,config = <&slpm_out_hi_wkup_pdis>;
-					};
-
-					sleep_cfg3 {
-						pins = "GPIO3_AH3"; /* TXD */
-						ste,config = <&slpm_out_wkup_pdis>;
-					};
-				};
-			};
-
-			uart1 {
-				uart1_default_mode: uart1_default {
-					default_mux {
-						function = "u1";
-						groups = "u1rxtx_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO4_AH6"; /* RXD */
-						ste,config = <&in_pu>;
-					};
-
-					default_cfg2 {
-						pins = "GPIO5_AG6"; /* TXD */
-						ste,config = <&out_hi>;
-					};
-				};
-
-				uart1_sleep_mode: uart1_sleep {
-					sleep_cfg1 {
-						pins = "GPIO4_AH6"; /* RXD */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-
-					sleep_cfg2 {
-						pins = "GPIO5_AG6"; /* TXD */
-						ste,config = <&slpm_out_wkup_pdis>;
-					};
-				};
-			};
-
-			uart2 {
-				uart2_default_mode: uart2_default {
-					default_mux {
-						function = "u2";
-						groups = "u2rxtx_c_1";
-					};
-					default_cfg1 {
-						pins = "GPIO29_W2"; /* RXD */
-						ste,config = <&in_pu>;
-					};
-
-					default_cfg2 {
-						pins = "GPIO30_W3"; /* TXD */
-						ste,config = <&out_hi>;
-					};
-				};
-
-				uart2_sleep_mode: uart2_sleep {
-					sleep_cfg1 {
-						pins = "GPIO29_W2"; /* RXD */
-						ste,config = <&in_wkup_pdis>;
-					};
-
-					sleep_cfg2 {
-						pins = "GPIO30_W3"; /* TXD */
-						ste,config = <&out_wkup_pdis>;
-					};
-				};
-			};
-
-			/* Settings for all I2C default and sleep states */
-			i2c0 {
-				i2c0_default_mode: i2c_default {
-					default_mux {
-						function = "i2c0";
-						groups = "i2c0_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				i2c0_sleep_mode: i2c_sleep {
-					sleep_cfg1 {
-						pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			i2c1 {
-				i2c1_default_mode: i2c_default {
-					default_mux {
-						function = "i2c1";
-						groups = "i2c1_b_2";
-					};
-					default_cfg1 {
-						pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				i2c1_sleep_mode: i2c_sleep {
-					sleep_cfg1 {
-						pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			i2c2 {
-				i2c2_default_mode: i2c_default {
-					default_mux {
-						function = "i2c2";
-						groups = "i2c2_b_2";
-					};
-					default_cfg1 {
-						pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				i2c2_sleep_mode: i2c_sleep {
-					sleep_cfg1 {
-						pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			i2c3 {
-				i2c3_default_mode: i2c_default {
-					default_mux {
-						function = "i2c3";
-						groups = "i2c3_c_2";
-					};
-					default_cfg1 {
-						pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				i2c3_sleep_mode: i2c_sleep {
-					sleep_cfg1 {
-						pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			/*
-			 * Activating I2C4 will conflict with UART1 about the same pins so do not
-			 * enable I2C4 and UART1 at the same time.
-			 */
-			i2c4 {
-				i2c4_default_mode: i2c_default {
-					default_mux {
-						function = "i2c4";
-						groups = "i2c4_b_1";
-					};
-					default_cfg1 {
-						pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				i2c4_sleep_mode: i2c_sleep {
-					sleep_cfg1 {
-						pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			/* Settings for all SPI default and sleep states */
-			spi2 {
-				spi2_default_mode: spi_default {
-					default_mux {
-						function = "spi2";
-						groups = "spi2_oc1_2";
-					};
-					default_cfg1 {
-						pins = "GPIO216_AG12"; /* FRM */
-						ste,config = <&gpio_out_hi>;
-					};
-					default_cfg2 {
-						pins = "GPIO218_AH11"; /* RXD */
-						ste,config = <&in_pd>;
-					};
-					default_cfg3 {
-						pins =
-						"GPIO215_AH13", /* TXD */
-						"GPIO217_AH12"; /* CLK */
-						ste,config = <&out_lo>;
-					};
-				};
-
-				spi2_idle_mode: spi_idle {
-					/*
-					 * The idle mode is basically sleep mode sans wakeups. Also
-					 * note that we have muxes the pins off the function here
-					 * as we do not state any muxing.
-					 */
-					idle_cfg1 {
-						pins = "GPIO218_AH11"; /* RXD */
-						ste,config = <&slpm_in_pdis>;
-					};
-					idle_cfg2 {
-						pins = "GPIO215_AH13"; /* TXD */
-						ste,config = <&slpm_out_lo_pdis>;
-					};
-					idle_cfg3 {
-						pins = "GPIO217_AH12"; /* CLK */
-						ste,config = <&slpm_pdis>;
-					};
-				};
-
-				spi2_sleep_mode: spi_sleep {
-					sleep_cfg1 {
-						pins =
-						"GPIO216_AG12", /* FRM */
-						"GPIO218_AH11"; /* RXD */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-					sleep_cfg2 {
-						pins = "GPIO215_AH13"; /* TXD */
-						ste,config = <&slpm_out_lo_wkup_pdis>;
-					};
-					sleep_cfg3 {
-						pins = "GPIO217_AH12"; /* CLK */
-						ste,config = <&slpm_wkup_pdis>;
-					};
-				};
-			};
-
-			/* Settings for all MMC/SD/SDIO default and sleep states */
-			sdi0 {
-				/* This is the external SD card slot, 4 bits wide */
-				sdi0_default_mode: sdi0_default {
-					default_mux {
-						function = "mc0";
-						groups = "mc0_a_1";
-					};
-					default_cfg1 {
-						pins =
-						"GPIO18_AC2", /* CMDDIR */
-						"GPIO19_AC1", /* DAT0DIR */
-						"GPIO20_AB4"; /* DAT2DIR */
-						ste,config = <&out_hi>;
-					};
-					default_cfg2 {
-						pins = "GPIO22_AA3"; /* FBCLK */
-						ste,config = <&in_nopull>;
-					};
-					default_cfg3 {
-						pins = "GPIO23_AA4"; /* CLK */
-						ste,config = <&out_lo>;
-					};
-					default_cfg4 {
-						pins =
-						"GPIO24_AB2", /* CMD */
-						"GPIO25_Y4", /* DAT0 */
-						"GPIO26_Y2", /* DAT1 */
-						"GPIO27_AA2", /* DAT2 */
-						"GPIO28_AA1"; /* DAT3 */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				sdi0_sleep_mode: sdi0_sleep {
-					sleep_cfg1 {
-						pins =
-						"GPIO18_AC2", /* CMDDIR */
-						"GPIO19_AC1", /* DAT0DIR */
-						"GPIO20_AB4"; /* DAT2DIR */
-						ste,config = <&slpm_out_hi_wkup_pdis>;
-					};
-					sleep_cfg2 {
-						pins =
-						"GPIO22_AA3", /* FBCLK */
-						"GPIO24_AB2", /* CMD */
-						"GPIO25_Y4", /* DAT0 */
-						"GPIO26_Y2", /* DAT1 */
-						"GPIO27_AA2", /* DAT2 */
-						"GPIO28_AA1"; /* DAT3 */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-					sleep_cfg3 {
-						pins = "GPIO23_AA4"; /* CLK */
-						ste,config = <&slpm_out_lo_wkup_pdis>;
-					};
-				};
-			};
-
-			sdi1 {
-				/* This is the WLAN SDIO 4 bits wide */
-				sdi1_default_mode: sdi1_default {
-					default_mux {
-						function = "mc1";
-						groups = "mc1_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO208_AH16"; /* CLK */
-						ste,config = <&out_lo>;
-					};
-					default_cfg2 {
-						pins = "GPIO209_AG15"; /* FBCLK */
-						ste,config = <&in_nopull>;
-					};
-					default_cfg3 {
-						pins =
-						"GPIO210_AJ15", /* CMD */
-						"GPIO211_AG14", /* DAT0 */
-						"GPIO212_AF13", /* DAT1 */
-						"GPIO213_AG13", /* DAT2 */
-						"GPIO214_AH15"; /* DAT3 */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				sdi1_sleep_mode: sdi1_sleep {
-					sleep_cfg1 {
-						pins = "GPIO208_AH16"; /* CLK */
-						ste,config = <&slpm_out_lo_wkup_pdis>;
-					};
-					sleep_cfg2 {
-						pins =
-						"GPIO209_AG15", /* FBCLK */
-						"GPIO210_AJ15", /* CMD */
-						"GPIO211_AG14", /* DAT0 */
-						"GPIO212_AF13", /* DAT1 */
-						"GPIO213_AG13", /* DAT2 */
-						"GPIO214_AH15"; /* DAT3 */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			sdi2 {
-				/* This is the eMMC 8 bits wide, usually PoP eMMC */
-				sdi2_default_mode: sdi2_default {
-					default_mux {
-						function = "mc2";
-						groups = "mc2_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO128_A5"; /* CLK */
-						ste,config = <&out_lo>;
-					};
-					default_cfg2 {
-						pins = "GPIO130_C8"; /* FBCLK */
-						ste,config = <&in_nopull>;
-					};
-					default_cfg3 {
-						pins =
-						"GPIO129_B4", /* CMD */
-						"GPIO131_A12", /* DAT0 */
-						"GPIO132_C10", /* DAT1 */
-						"GPIO133_B10", /* DAT2 */
-						"GPIO134_B9", /* DAT3 */
-						"GPIO135_A9", /* DAT4 */
-						"GPIO136_C7", /* DAT5 */
-						"GPIO137_A7", /* DAT6 */
-						"GPIO138_C5"; /* DAT7 */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				sdi2_sleep_mode: sdi2_sleep {
-					sleep_cfg1 {
-						pins = "GPIO128_A5"; /* CLK */
-						ste,config = <&out_lo_wkup_pdis>;
-					};
-					sleep_cfg2 {
-						pins =
-						"GPIO130_C8", /* FBCLK */
-						"GPIO129_B4"; /* CMD */
-						ste,config = <&in_wkup_pdis_en>;
-					};
-					sleep_cfg3 {
-						pins =
-						"GPIO131_A12", /* DAT0 */
-						"GPIO132_C10", /* DAT1 */
-						"GPIO133_B10", /* DAT2 */
-						"GPIO134_B9", /* DAT3 */
-						"GPIO135_A9", /* DAT4 */
-						"GPIO136_C7", /* DAT5 */
-						"GPIO137_A7", /* DAT6 */
-						"GPIO138_C5"; /* DAT7 */
-						ste,config = <&in_wkup_pdis>;
-					};
-				};
-			};
-
-			sdi4 {
-				/* This is the eMMC 8 bits wide, usually PCB-mounted eMMC */
-				sdi4_default_mode: sdi4_default {
-					default_mux {
-						function = "mc4";
-						groups = "mc4_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO203_AE23"; /* CLK */
-						ste,config = <&out_lo>;
-					};
-					default_cfg2 {
-						pins = "GPIO202_AF25"; /* FBCLK */
-						ste,config = <&in_nopull>;
-					};
-					default_cfg3 {
-						pins =
-						"GPIO201_AF24", /* CMD */
-						"GPIO200_AH26", /* DAT0 */
-						"GPIO199_AH23", /* DAT1 */
-						"GPIO198_AG25", /* DAT2 */
-						"GPIO197_AH24", /* DAT3 */
-						"GPIO207_AJ23", /* DAT4 */
-						"GPIO206_AG24", /* DAT5 */
-						"GPIO205_AG23", /* DAT6 */
-						"GPIO204_AF23"; /* DAT7 */
-						ste,config = <&in_pu>;
-					};
-				};
-
-				sdi4_sleep_mode: sdi4_sleep {
-					sleep_cfg1 {
-						pins = "GPIO203_AE23"; /* CLK */
-						ste,config = <&out_lo_wkup_pdis>;
-					};
-					sleep_cfg2 {
-						pins =
-						"GPIO202_AF25", /* FBCLK */
-						"GPIO201_AF24", /* CMD */
-						"GPIO200_AH26", /* DAT0 */
-						"GPIO199_AH23", /* DAT1 */
-						"GPIO198_AG25", /* DAT2 */
-						"GPIO197_AH24", /* DAT3 */
-						"GPIO207_AJ23", /* DAT4 */
-						"GPIO206_AG24", /* DAT5 */
-						"GPIO205_AG23", /* DAT6 */
-						"GPIO204_AF23"; /* DAT7 */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			/*
-			 * Multi-rate serial ports (MSPs) - MSP3 output is internal and
-			 * cannot be muxed onto any pins.
-			 */
-			msp0 {
-				msp0_default_mode: msp0_default {
-					default_msp0_mux {
-						function = "msp0";
-						groups = "msp0txrx_a_1", "msp0tfstck_a_1";
-					};
-					default_msp0_cfg {
-						pins =
-						"GPIO12_AC4", /* TXD */
-						"GPIO15_AC3", /* RXD */
-						"GPIO13_AF3", /* TFS */
-						"GPIO14_AE3"; /* TCK */
-						ste,config = <&in_nopull>;
-					};
-				};
-			};
-
-			msp1 {
-				msp1_default_mode: msp1_default {
-					default_mux {
-						function = "msp1";
-						groups = "msp1txrx_a_1", "msp1_a_1";
-					};
-					default_cfg1 {
-						pins = "GPIO33_AF2";
-						ste,config = <&out_lo>;
-					};
-					default_cfg2 {
-						pins =
-						"GPIO34_AE1",
-						"GPIO35_AE2",
-						"GPIO36_AG2";
-						ste,config = <&in_nopull>;
-					};
-
-				};
-			};
-
-			msp2 {
-				msp2_default_mode: msp2_default {
-					/* MSP2 usually used for HDMI audio */
-					default_mux {
-						function = "msp2";
-						groups = "msp2_a_1";
-					};
-					default_cfg1 {
-						pins =
-						"GPIO193_AH27", /* TXD */
-						"GPIO194_AF27", /* TCK */
-						"GPIO195_AG28"; /* TFS */
-						ste,config = <&in_pd>;
-					};
-					default_cfg2 {
-						pins = "GPIO196_AG26"; /* RXD */
-						ste,config = <&out_lo>;
-					};
-				};
-			};
-
-
-			musb {
-				musb_default_mode: musb_default {
-					default_mux {
-						function = "usb";
-						groups = "usb_a_1";
-					};
-					default_cfg1 {
-						pins =
-						"GPIO256_AF28", /* NXT */
-						"GPIO258_AD29", /* XCLK */
-						"GPIO259_AC29", /* DIR */
-						"GPIO260_AD28", /* DAT7 */
-						"GPIO261_AD26", /* DAT6 */
-						"GPIO262_AE26", /* DAT5 */
-						"GPIO263_AG29", /* DAT4 */
-						"GPIO264_AE27", /* DAT3 */
-						"GPIO265_AD27", /* DAT2 */
-						"GPIO266_AC28", /* DAT1 */
-						"GPIO267_AC27"; /* DAT0 */
-						ste,config = <&in_nopull>;
-					};
-					default_cfg2 {
-						pins = "GPIO257_AE29"; /* STP */
-						ste,config = <&out_hi>;
-					};
-				};
-
-				musb_sleep_mode: musb_sleep {
-					sleep_cfg1 {
-						pins =
-						"GPIO256_AF28", /* NXT */
-						"GPIO258_AD29", /* XCLK */
-						"GPIO259_AC29"; /* DIR */
-						ste,config = <&slpm_wkup_pdis_en>;
-					};
-					sleep_cfg2 {
-						pins = "GPIO257_AE29"; /* STP */
-						ste,config = <&slpm_out_hi_wkup_pdis>;
-					};
-					sleep_cfg3 {
-						pins =
-						"GPIO260_AD28", /* DAT7 */
-						"GPIO261_AD26", /* DAT6 */
-						"GPIO262_AE26", /* DAT5 */
-						"GPIO263_AG29", /* DAT4 */
-						"GPIO264_AE27", /* DAT3 */
-						"GPIO265_AD27", /* DAT2 */
-						"GPIO266_AC28", /* DAT1 */
-						"GPIO267_AC27"; /* DAT0 */
-						ste,config = <&slpm_in_wkup_pdis_en>;
-					};
-				};
-			};
-
-			mcde {
-				lcd_default_mode: lcd_default {
-					default_mux1 {
-						/* Mux in VSI0 and all the data lines */
-						function = "lcd";
-						groups =
-						"lcdvsi0_a_1", /* VSI0 for LCD */
-						"lcd_d0_d7_a_1", /* Data lines */
-						"lcdvsi1_a_1"; /* VSI1 for HDMI */
-					};
-					default_mux2 {
-						function = "lcda";
-						groups =
-						"lcdaclk_b_1"; /* Clock line for TV-out */
-					};
-					default_cfg1 {
-						pins =
-						"GPIO68_E1", /* VSI0 */
-						"GPIO69_E2"; /* VSI1 */
-						ste,config = <&in_pu>;
-					};
-				};
-				lcd_sleep_mode: lcd_sleep {
-					sleep_cfg1 {
-						pins = "GPIO69_E2"; /* VSI1 */
-						ste,config = <&slpm_in_wkup_pdis>;
-					};
-				};
-			};
-
-			ske {
-				/* SKE keys on position 2 in an 8x8 matrix */
-				ske_kpa2_default_mode: ske_kpa2_default {
-					default_mux {
-						function = "kp";
-						groups = "kp_a_2";
-					};
-					default_cfg1 {
-						pins =
-						"GPIO153_B17", /* I7 */
-						"GPIO154_C16", /* I6 */
-						"GPIO155_C19", /* I5 */
-						"GPIO156_C17", /* I4 */
-						"GPIO161_D21", /* I3 */
-						"GPIO162_D20", /* I2 */
-						"GPIO163_C20", /* I1 */
-						"GPIO164_B21"; /* I0 */
-						ste,config = <&in_pd>;
-					};
-					default_cfg2 {
-						pins =
-						"GPIO157_A18", /* O7 */
-						"GPIO158_C18", /* O6 */
-						"GPIO159_B19", /* O5 */
-						"GPIO160_B20", /* O4 */
-						"GPIO165_C21", /* O3 */
-						"GPIO166_A22", /* O2 */
-						"GPIO167_B24", /* O1 */
-						"GPIO168_C22"; /* O0 */
-						ste,config = <&out_lo>;
-					};
-				};
-				ske_kpa2_sleep_mode: ske_kpa2_sleep {
-					sleep_cfg1 {
-						pins =
-						"GPIO153_B17", /* I7 */
-						"GPIO154_C16", /* I6 */
-						"GPIO155_C19", /* I5 */
-						"GPIO156_C17", /* I4 */
-						"GPIO161_D21", /* I3 */
-						"GPIO162_D20", /* I2 */
-						"GPIO163_C20", /* I1 */
-						"GPIO164_B21"; /* I0 */
-						ste,config = <&slpm_in_pu_wkup_pdis_en>;
-					};
-					sleep_cfg2 {
-						pins =
-						"GPIO157_A18", /* O7 */
-						"GPIO158_C18", /* O6 */
-						"GPIO159_B19", /* O5 */
-						"GPIO160_B20", /* O4 */
-						"GPIO165_C21", /* O3 */
-						"GPIO166_A22", /* O2 */
-						"GPIO167_B24", /* O1 */
-						"GPIO168_C22"; /* O0 */
-						ste,config = <&slpm_out_lo_pdis>;
-					};
-				};
-				/*
-				 * SKE keys on position 1 and "other C1" combi giving
-				 * six rows of six keys.
-				 */
-				ske_kpaoc1_default_mode: ske_kpaoc1_default {
-					default_mux {
-						function = "kp";
-						groups = "kp_a_1", "kp_oc1_1";
-					};
-					default_cfg1 {
-						pins =
-						"GPIO91_B6", /* KP_O0 */
-						"GPIO90_A3", /* KP_O1 */
-						"GPIO87_B3", /* KP_O2 */
-						"GPIO86_C6", /* KP_O3 */
-						"GPIO96_D8", /* KP_O6 */
-						"GPIO94_D7"; /* KP_O7 */
-						ste,config = <&out_lo>;
-					};
-					default_cfg2 {
-						pins =
-						"GPIO93_B7", /* KP_I0 */
-						"GPIO92_D6", /* KP_I1 */
-						"GPIO89_E6", /* KP_I2 */
-						"GPIO88_C4", /* KP_I3 */
-						"GPIO97_D9", /* KP_I6 */
-						"GPIO95_E8"; /* KP_I7 */
-						ste,config = <&in_pu>;
-					};
-				};
-			};
-
-			wlan {
-				wlan_default_mode: wlan_default {
-					/*
-					 * Activate this mode with the WLAN chip.
-					 * These are plain GPIO pins used by WLAN
-					 */
-					default_cfg1 {
-						pins =
-						"GPIO226_AF8", /* WLAN_PMU_EN */
-						"GPIO85_D5"; /* WLAN_ENA */
-						ste,config = <&gpio_out_lo>;
-					};
-					default_cfg2 {
-						pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */
-						ste,config = <&gpio_in_pu>;
-					};
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
deleted file mode 100644
index 60eed262d920..000000000000
--- a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
+++ /dev/null
@@ -1,20 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 ST-Ericsson AB
- */
-
-/dts-v1/;
-#include "ste-hrefprev60.dtsi"
-#include "ste-href-tvk1281618.dtsi"
-
-/ {
-	model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB";
-	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
-
-	/* This stablilizes the serial port enumeration */
-	aliases {
-		serial0 = &ux500_serial0;
-		serial1 = &ux500_serial1;
-		serial2 = &ux500_serial2;
-	};
-};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts
deleted file mode 100644
index 9be513aad549..000000000000
--- a/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts
+++ /dev/null
@@ -1,43 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 ST-Ericsson AB
- *
- * Device Tree for the HREF version 60 or later with the ST UIB
- */
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "ste-hrefv60plus.dtsi"
-#include "ste-href-stuib.dtsi"
-
-/ {
-	model = "ST-Ericsson HREF (v60+) and ST UIB";
-	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
-
-	/* This stablilizes the serial port enumeration */
-	aliases {
-		serial0 = &ux500_serial0;
-		serial1 = &ux500_serial1;
-		serial2 = &ux500_serial2;
-	};
-
-	soc {
-		/* Reset line for the BU21013 touchscreen */
-		i2c@80110000 {
-			/* Only one of these will be used */
-			bu21013_tp@5c {
-				interrupt-parent = <&gpio2>;
-				interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
-				touch-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
-				reset-gpios = <&gpio4 17 GPIO_LINE_OPEN_DRAIN>;
-			};
-			bu21013_tp@5d {
-				interrupt-parent = <&gpio2>;
-				interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
-				touch-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
-				reset-gpios = <&gpio4 17 GPIO_LINE_OPEN_DRAIN>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
deleted file mode 100644
index 73ea3100f186..000000000000
--- a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
+++ /dev/null
@@ -1,22 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 ST-Ericsson AB
- *
- * Device Tree for the HREF version 60 or later with the TVK1281618 UIB
- */
-
-/dts-v1/;
-#include "ste-hrefv60plus.dtsi"
-#include "ste-href-tvk1281618.dtsi"
-
-/ {
-	model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB";
-	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
-
-	/* This stablilizes the serial port enumeration */
-	aliases {
-		serial0 = &ux500_serial0;
-		serial1 = &ux500_serial1;
-		serial2 = &ux500_serial2;
-	};
-};
diff --git a/arch/arm/boot/dts/ste-u300.dts b/arch/arm/boot/dts/ste-u300.dts
deleted file mode 100644
index f4e7660fead7..000000000000
--- a/arch/arm/boot/dts/ste-u300.dts
+++ /dev/null
@@ -1,464 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree for the ST-Ericsson U300 Machine and SoC
- */
-
-/dts-v1/;
-
-/ {
-	model = "ST-Ericsson U300";
-	compatible = "stericsson,u300";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	chosen {
-		bootargs = "root=/dev/ram0 console=ttyAMA0,115200n8 earlyprintk";
-	};
-
-	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-        };
-
-	memory {
-		device_type = "memory";
-		reg = <0x48000000 0x03c00000>;
-	};
-
-	s365 {
-		compatible = "stericsson,s365";
-		vana15-supply = <&ab3100_ldo_d_reg>;
-		syscon = <&syscon>;
-	};
-
-	syscon: syscon@c0011000 {
-		compatible = "stericsson,u300-syscon", "syscon";
-		reg = <0xc0011000 0x1000>;
-		clk32: app_32_clk@32k {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-		};
-		pll13: pll13@13M {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
-		};
-		/* Slow bridge clocks under PLL13 */
-		slow_clk: slow_clk@13M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <0>; /* Slow */
-			clock-id = <0>;
-			clocks = <&pll13>;
-		};
-		uart0_clk: uart0_clk@13M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <0>; /* Slow */
-			clock-id = <1>;
-			clocks = <&slow_clk>;
-		};
-		gpio_clk: gpio_clk@13M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <0>; /* Slow */
-			clock-id = <4>;
-			clocks = <&slow_clk>;
-		};
-		rtc_clk: rtc_clk@13M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <0>; /* Slow */
-			clock-id = <6>;
-			clocks = <&slow_clk>;
-		};
-		apptimer_clk: app_tmr_clk@13M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <0>; /* Slow */
-			clock-id = <7>;
-			clocks = <&slow_clk>;
-		};
-		acc_tmr_clk@13M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <0>; /* Slow */
-			clock-id = <8>;
-			clocks = <&slow_clk>;
-		};
-		pll208: pll208@208M {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <208000000>;
-		};
-		app208: app_208_clk@208M {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clock-div = <1>;
-			clock-mult = <1>;
-			clocks = <&pll208>;
-		};
-		cpu_clk@208M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <3>;
-			clocks = <&app208>;
-		};
-		app104: app_104_clk@104M {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clock-div = <2>;
-			clock-mult = <1>;
-			clocks = <&pll208>;
-		};
-		semi_clk@104M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <9>;
-			clocks = <&app104>;
-		};
-		app52: app_52_clk@52M {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clock-div = <4>;
-			clock-mult = <1>;
-			clocks = <&pll208>;
-		};
-		/* AHB subsystem clocks */
-		ahb_clk: ahb_subsys_clk@52M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <10>;
-			clocks = <&app52>;
-		};
-		intcon_clk@52M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <12>;
-			clocks = <&ahb_clk>;
-		};
-		emif_clk@52M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <5>;
-			clocks = <&ahb_clk>;
-		};
-		dmac_clk: dmac_clk@52M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <4>;
-			clocks = <&app52>;
-		};
-		fsmc_clk: fsmc_clk@52M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <6>;
-			clocks = <&app52>;
-		};
-		xgam_clk: xgam_clk@52M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <2>; /* Rest */
-			clock-id = <8>;
-			clocks = <&app52>;
-		};
-		app26: app_26_clk@26M {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clock-div = <2>;
-			clock-mult = <1>;
-			clocks = <&app52>;
-		};
-		/* Fast bridge  clocks */
-		fast_clk: fast_clk@26M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <1>; /* Fast */
-			clock-id = <0>;
-			clocks = <&app26>;
-		};
-		i2c0_clk: i2c0_clk@26M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <1>; /* Fast */
-			clock-id = <1>;
-			clocks = <&fast_clk>;
-		};
-		i2c1_clk: i2c1_clk@26M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <1>; /* Fast */
-			clock-id = <2>;
-			clocks = <&fast_clk>;
-		};
-		mmc_pclk: mmc_p_clk@26M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <1>; /* Fast */
-			clock-id = <5>;
-			clocks = <&fast_clk>;
-		};
-		mmc_mclk: mmc_mclk {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-mclk";
-			clocks = <&mmc_pclk>;
-		};
-		spi_clk: spi_p_clk@26M {
-			#clock-cells = <0>;
-			compatible = "stericsson,u300-syscon-clk";
-			clock-type = <1>; /* Fast */
-			clock-id = <6>;
-			clocks = <&fast_clk>;
-		};
-	};
-
-	timer: timer@c0014000 {
-		compatible = "stericsson,u300-apptimer";
-		reg = <0xc0014000 0x1000>;
-		interrupt-parent = <&vica>;
-		interrupts = <24 25 26 27>;
-		clocks = <&apptimer_clk>;
-	};
-
-	gpio: gpio@c0016000 {
-		compatible = "stericsson,gpio-coh901";
-		reg = <0xc0016000 0x1000>;
-		interrupt-parent = <&vicb>;
-		interrupts = <0 1 2 18 21 22 23>;
-		clocks = <&gpio_clk>;
-		interrupt-names = "gpio0", "gpio1", "gpio2", "gpio3",
-				"gpio4", "gpio5", "gpio6";
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	pinctrl: pinctrl@c0011000 {
-		compatible = "stericsson,pinctrl-u300";
-		reg = <0xc0011000 0x1000>;
-	};
-
-	watchdog: watchdog@c0012000 {
-		compatible = "stericsson,coh901327";
-		reg = <0xc0012000 0x1000>;
-		interrupt-parent = <&vicb>;
-		interrupts = <3>;
-		clocks = <&clk32>;
-	};
-
-	rtc: rtc@c0017000 {
-		compatible = "stericsson,coh901331";
-		reg = <0xc0017000 0x1000>;
-		interrupt-parent = <&vicb>;
-		interrupts = <10>;
-		clocks = <&rtc_clk>;
-	};
-
-	dmac: dma-controller@c00020000 {
-		compatible = "stericsson,coh901318";
-		reg = <0xc0020000 0x1000>;
-		interrupt-parent = <&vica>;
-		interrupts = <2>;
-		#dma-cells = <1>;
-		dma-channels = <40>;
-		clocks = <&dmac_clk>;
-	};
-
-	/* A NAND flash of 128 MiB */
-	fsmc: flash@40000000 {
-		compatible = "stericsson,fsmc-nand";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		reg = <0x9f800000 0x1000>,	/* FSMC Register*/
-			<0x80000000 0x4000>,	/* NAND Base DATA */
-			<0x80020000 0x4000>,	/* NAND Base ADDR */
-			<0x80010000 0x4000>;	/* NAND Base CMD */
-		reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
-		nand-skip-bbtscan;
-		clocks = <&fsmc_clk>;
-
-		partition@0 {
-		label = "boot records";
-			reg = <0x0 0x20000>;
-		};
-		partition@20000 {
-			label = "free";
-			reg = <0x20000 0x7e0000>;
-		};
-		partition@800000 {
-			label = "platform";
-			reg = <0x800000 0xf800000>;
-		};
-	};
-
-	i2c0: i2c@c0004000 {
-		compatible = "st,ddci2c";
-		reg = <0xc0004000 0x1000>;
-		interrupt-parent = <&vicb>;
-		interrupts = <8>;
-		clocks = <&i2c0_clk>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		ab3100: ab3100@48 {
-			compatible = "stericsson,ab3100";
-			reg = <0x48>;
-			interrupt-parent = <&vica>;
-			interrupts = <0>; /* EXT0 IRQ */
-			ab3100-regulators {
-				compatible = "stericsson,ab3100-regulators";
-				ab3100_ldo_a_reg: ab3100_ldo_a {
-					startup-delay-us = <200>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-				ab3100_ldo_c_reg: ab3100_ldo_c {
-					startup-delay-us = <200>;
-				};
-				ab3100_ldo_d_reg: ab3100_ldo_d {
-					startup-delay-us = <200>;
-				};
-				ab3100_ldo_e_reg: ab3100_ldo_e {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					startup-delay-us = <200>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-				ab3100_ldo_f_reg: ab3100_ldo_f {
-					regulator-min-microvolt = <2500000>;
-					regulator-max-microvolt = <2500000>;
-					startup-delay-us = <600>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-				ab3100_ldo_g_reg: ab3100_ldo_g {
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <2850000>;
-					startup-delay-us = <400>;
-				};
-				ab3100_ldo_h_reg: ab3100_ldo_h {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <2750000>;
-					startup-delay-us = <200>;
-				};
-				ab3100_ldo_k_reg: ab3100_ldo_k {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2750000>;
-					startup-delay-us = <200>;
-				};
-				ab3100_ext_reg: ab3100_ext {
-				};
-				ab3100_buck_reg: ab3100_buck {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1800000>;
-					startup-delay-us = <1000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-			};
-		};
-	};
-
-	i2c1: i2c@c0005000 {
-		compatible = "st,ddci2c";
-		reg = <0xc0005000 0x1000>;
-		interrupt-parent = <&vicb>;
-		interrupts = <9>;
-		clocks = <&i2c1_clk>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		fwcam0: fwcam@10 {
-			reg = <0x10>;
-		};
-		fwcam1: fwcam@5d {
-			reg = <0x5d>;
-		};
-	};
-
-	amba {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		vica: interrupt-controller@a0001000 {
-			compatible = "arm,versatile-vic";
-			interrupt-controller;
-			#interrupt-cells = <1>;
-			reg = <0xa0001000 0x20>;
-		};
-
-		vicb: interrupt-controller@a0002000 {
-			compatible = "arm,versatile-vic";
-			interrupt-controller;
-			#interrupt-cells = <1>;
-			reg = <0xa0002000 0x20>;
-		};
-
-		uart0: serial@c0013000 {
-			compatible = "arm,pl011", "arm,primecell";
-			reg = <0xc0013000 0x1000>;
-			interrupt-parent = <&vica>;
-			interrupts = <22>;
-			clocks = <&uart0_clk>, <&uart0_clk>;
-			clock-names = "apb_pclk", "uart0_clk";
-			dmas = <&dmac 17 &dmac 18>;
-			dma-names = "tx", "rx";
-		};
-
-		uart1: serial@c0007000 {
-			compatible = "arm,pl011", "arm,primecell";
-			reg = <0xc0007000 0x1000>;
-			interrupt-parent = <&vicb>;
-			interrupts = <20>;
-			dmas = <&dmac 38 &dmac 39>;
-			dma-names = "tx", "rx";
-		};
-
-		mmcsd: mmcsd@c0001000 {
-			compatible = "arm,pl18x", "arm,primecell";
-			reg = <0xc0001000 0x1000>;
-			interrupt-parent = <&vicb>;
-			interrupts = <6 7>;
-			clocks = <&mmc_pclk>, <&mmc_mclk>;
-			clock-names = "apb_pclk", "mclk";
-			max-frequency = <24000000>;
-			bus-width = <4>; // SD-card slot
-			cap-mmc-highspeed;
-			cap-sd-highspeed;
-			cd-gpios = <&gpio 12 0x4>;
-			cd-inverted;
-			vmmc-supply = <&ab3100_ldo_g_reg>;
-			dmas = <&dmac 14>;
-			dma-names = "rx";
-		};
-
-		spi: spi@c0006000 {
-			compatible = "arm,pl022", "arm,primecell";
-			reg = <0xc0006000 0x1000>;
-			interrupt-parent = <&vica>;
-			interrupts = <23>;
-			clocks = <&spi_clk>, <&spi_clk>;
-			clock-names = "SSPCLK", "apb_pclk";
-			dmas = <&dmac 27 &dmac 28>;
-			dma-names = "tx", "rx";
-			num-cs = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			spi-dummy@1 {
-				compatible = "arm,pl022-dummy";
-				reg = <1>;
-				spi-max-frequency = <20000000>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stih407-clock.dtsi b/arch/arm/boot/dts/stih407-clock.dtsi
deleted file mode 100644
index 1ab40db7c91a..000000000000
--- a/arch/arm/boot/dts/stih407-clock.dtsi
+++ /dev/null
@@ -1,323 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2014 STMicroelectronics R&D Limited
- */
-#include <dt-bindings/clock/stih407-clks.h>
-/ {
-	/*
-	 * Fixed 30MHz oscillator inputs to SoC
-	 */
-	clk_sysin: clk-sysin {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <30000000>;
-	};
-
-	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		/*
-		 * A9 PLL.
-		 */
-		clockgen-a9@92b0000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x92b0000 0xffff>;
-
-			clockgen_a9_pll: clockgen-a9-pll {
-				#clock-cells = <1>;
-				compatible = "st,stih407-clkgen-plla9";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clockgen-a9-pll-odf";
-			};
-		};
-
-		/*
-		 * ARM CPU related clocks.
-		 */
-		clk_m_a9: clk-m-a9@92b0000 {
-			#clock-cells = <0>;
-			compatible = "st,stih407-clkgen-a9-mux";
-			reg = <0x92b0000 0x10000>;
-
-			clocks = <&clockgen_a9_pll 0>,
-				 <&clockgen_a9_pll 0>,
-				 <&clk_s_c0_flexgen 13>,
-				 <&clk_m_a9_ext2f_div2>;
-
-
-			/*
-			 * ARM Peripheral clock for timers
-			 */
-			arm_periph_clk: clk-m-a9-periphs {
-				#clock-cells = <0>;
-				compatible = "fixed-factor-clock";
-
-				clocks = <&clk_m_a9>;
-				clock-div = <2>;
-				clock-mult = <1>;
-			};
-		};
-
-		clockgen-a@90ff000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x90ff000 0x1000>;
-
-			clk_s_a0_pll: clk-s-a0-pll {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll0";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-a0-pll-ofd-0";
-				clock-critical = <0>; /* clk-s-a0-pll-ofd-0 */
-			};
-
-			clk_s_a0_flexgen: clk-s-a0-flexgen {
-				compatible = "st,flexgen";
-
-				#clock-cells = <1>;
-
-				clocks = <&clk_s_a0_pll 0>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-ic-lmi0";
-				clock-critical = <CLK_IC_LMI0>;
-			};
-		};
-
-		clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-pll";
-			reg = <0x9103000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-c0-fs0-ch0",
-					     "clk-s-c0-fs0-ch1",
-					     "clk-s-c0-fs0-ch2",
-					     "clk-s-c0-fs0-ch3";
-			clock-critical = <0>; /* clk-s-c0-fs0-ch0 */
-		};
-
-		clk_s_c0: clockgen-c@9103000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9103000 0x1000>;
-
-			clk_s_c0_pll0: clk-s-c0-pll0 {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll0";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-c0-pll0-odf-0";
-				clock-critical = <0>; /* clk-s-c0-pll0-odf-0 */
-			};
-
-			clk_s_c0_pll1: clk-s-c0-pll1 {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll1";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-c0-pll1-odf-0";
-			};
-
-			clk_s_c0_flexgen: clk-s-c0-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen";
-
-				clocks = <&clk_s_c0_pll0 0>,
-					 <&clk_s_c0_pll1 0>,
-					 <&clk_s_c0_quadfs 0>,
-					 <&clk_s_c0_quadfs 1>,
-					 <&clk_s_c0_quadfs 2>,
-					 <&clk_s_c0_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-icn-gpu",
-						     "clk-fdma",
-						     "clk-nand",
-						     "clk-hva",
-						     "clk-proc-stfe",
-						     "clk-proc-tp",
-						     "clk-rx-icn-dmu",
-						     "clk-rx-icn-hva",
-						     "clk-icn-cpu",
-						     "clk-tx-icn-dmu",
-						     "clk-mmc-0",
-						     "clk-mmc-1",
-						     "clk-jpegdec",
-						     "clk-ext2fa9",
-						     "clk-ic-bdisp-0",
-						     "clk-ic-bdisp-1",
-						     "clk-pp-dmu",
-						     "clk-vid-dmu",
-						     "clk-dss-lpc",
-						     "clk-st231-aud-0",
-						     "clk-st231-gp-1",
-						     "clk-st231-dmu",
-						     "clk-icn-lmi",
-						     "clk-tx-icn-disp-1",
-						     "clk-icn-sbc",
-						     "clk-stfe-frc2",
-						     "clk-eth-phy",
-						     "clk-eth-ref-phyclk",
-						     "clk-flash-promip",
-						     "clk-main-disp",
-						     "clk-aux-disp",
-						     "clk-compo-dvp";
-				clock-critical = <CLK_PROC_STFE>,
-						 <CLK_ICN_CPU>,
-						 <CLK_TX_ICN_DMU>,
-						 <CLK_EXT2F_A9>,
-						 <CLK_ICN_LMI>,
-						 <CLK_ICN_SBC>;
-
-				/*
-				 * ARM Peripheral clock for timers
-				 */
-				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
-					#clock-cells = <0>;
-					compatible = "fixed-factor-clock";
-
-					clocks = <&clk_s_c0_flexgen 13>;
-
-					clock-output-names = "clk-m-a9-ext2f-div2";
-
-					clock-div = <2>;
-					clock-mult = <1>;
-				};
-			};
-		};
-
-		clk_s_d0_quadfs: clk-s-d0-quadfs@9104000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9104000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d0-fs0-ch0",
-					     "clk-s-d0-fs0-ch1",
-					     "clk-s-d0-fs0-ch2",
-					     "clk-s-d0-fs0-ch3";
-		};
-
-		clockgen-d0@9104000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9104000 0x1000>;
-
-			clk_s_d0_flexgen: clk-s-d0-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen-audio", "st,flexgen";
-
-				clocks = <&clk_s_d0_quadfs 0>,
-					 <&clk_s_d0_quadfs 1>,
-					 <&clk_s_d0_quadfs 2>,
-					 <&clk_s_d0_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-pcm-0",
-						     "clk-pcm-1",
-						     "clk-pcm-2",
-						     "clk-spdiff";
-			};
-		};
-
-		clk_s_d2_quadfs: clk-s-d2-quadfs@9106000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9106000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d2-fs0-ch0",
-					     "clk-s-d2-fs0-ch1",
-					     "clk-s-d2-fs0-ch2",
-					     "clk-s-d2-fs0-ch3";
-		};
-
-		clockgen-d2@9106000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9106000 0x1000>;
-
-			clk_s_d2_flexgen: clk-s-d2-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen-video", "st,flexgen";
-
-				clocks = <&clk_s_d2_quadfs 0>,
-					 <&clk_s_d2_quadfs 1>,
-					 <&clk_s_d2_quadfs 2>,
-					 <&clk_s_d2_quadfs 3>,
-					 <&clk_sysin>,
-					 <&clk_sysin>,
-					 <&clk_tmdsout_hdmi>;
-
-				clock-output-names = "clk-pix-main-disp",
-						     "clk-pix-pip",
-						     "clk-pix-gdp1",
-						     "clk-pix-gdp2",
-						     "clk-pix-gdp3",
-						     "clk-pix-gdp4",
-						     "clk-pix-aux-disp",
-						     "clk-denc",
-						     "clk-pix-hddac",
-						     "clk-hddac",
-						     "clk-sddac",
-						     "clk-pix-dvo",
-						     "clk-dvo",
-						     "clk-pix-hdmi",
-						     "clk-tmds-hdmi",
-						     "clk-ref-hdmiphy";
-						     };
-		};
-
-		clk_s_d3_quadfs: clk-s-d3-quadfs@9107000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9107000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d3-fs0-ch0",
-					     "clk-s-d3-fs0-ch1",
-					     "clk-s-d3-fs0-ch2",
-					     "clk-s-d3-fs0-ch3";
-		};
-
-		clockgen-d3@9107000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9107000 0x1000>;
-
-			clk_s_d3_flexgen: clk-s-d3-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen";
-
-				clocks = <&clk_s_d3_quadfs 0>,
-					 <&clk_s_d3_quadfs 1>,
-					 <&clk_s_d3_quadfs 2>,
-					 <&clk_s_d3_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-stfe-frc1",
-						     "clk-tsout-0",
-						     "clk-tsout-1",
-						     "clk-mchi",
-						     "clk-vsens-compo",
-						     "clk-frc1-remote",
-						     "clk-lpc-0",
-						     "clk-lpc-1";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stih410-clock.dtsi b/arch/arm/boot/dts/stih410-clock.dtsi
deleted file mode 100644
index 81a8c25d7ba5..000000000000
--- a/arch/arm/boot/dts/stih410-clock.dtsi
+++ /dev/null
@@ -1,333 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2014 STMicroelectronics R&D Limited
- */
-#include <dt-bindings/clock/stih410-clks.h>
-/ {
-	/*
-	 * Fixed 30MHz oscillator inputs to SoC
-	 */
-	clk_sysin: clk-sysin {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <30000000>;
-		clock-output-names = "CLK_SYSIN";
-	};
-
-	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		compatible = "st,stih410-clk", "simple-bus";
-
-		/*
-		 * A9 PLL.
-		 */
-		clockgen-a9@92b0000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x92b0000 0xffff>;
-
-			clockgen_a9_pll: clockgen-a9-pll {
-				#clock-cells = <1>;
-				compatible = "st,stih407-clkgen-plla9";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clockgen-a9-pll-odf";
-			};
-		};
-
-		/*
-		 * ARM CPU related clocks.
-		 */
-		clk_m_a9: clk-m-a9@92b0000 {
-			#clock-cells = <0>;
-			compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
-			reg = <0x92b0000 0x10000>;
-
-			clocks = <&clockgen_a9_pll 0>,
-				 <&clockgen_a9_pll 0>,
-				 <&clk_s_c0_flexgen 13>,
-				 <&clk_m_a9_ext2f_div2>;
-			/*
-			 * ARM Peripheral clock for timers
-			 */
-			arm_periph_clk: clk-m-a9-periphs {
-				#clock-cells = <0>;
-				compatible = "fixed-factor-clock";
-				clocks = <&clk_m_a9>;
-				clock-div = <2>;
-				clock-mult = <1>;
-			};
-		};
-
-		clockgen-a@90ff000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x90ff000 0x1000>;
-
-			clk_s_a0_pll: clk-s-a0-pll {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll0";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-a0-pll-ofd-0";
-				clock-critical = <0>; /* clk-s-a0-pll-ofd-0 */
-			};
-
-			clk_s_a0_flexgen: clk-s-a0-flexgen {
-				compatible = "st,flexgen";
-
-				#clock-cells = <1>;
-
-				clocks = <&clk_s_a0_pll 0>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-ic-lmi0",
-						     "clk-ic-lmi1";
-				clock-critical = <CLK_IC_LMI0>;
-			};
-		};
-
-		clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-pll";
-			reg = <0x9103000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-c0-fs0-ch0",
-					     "clk-s-c0-fs0-ch1",
-					     "clk-s-c0-fs0-ch2",
-					     "clk-s-c0-fs0-ch3";
-			clock-critical = <0>; /* clk-s-c0-fs0-ch0 */
-		};
-
-		clk_s_c0: clockgen-c@9103000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9103000 0x1000>;
-
-			clk_s_c0_pll0: clk-s-c0-pll0 {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll0";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-c0-pll0-odf-0";
-				clock-critical = <0>; /* clk-s-c0-pll0-odf-0 */
-			};
-
-			clk_s_c0_pll1: clk-s-c0-pll1 {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll1";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-c0-pll1-odf-0";
-			};
-
-			clk_s_c0_flexgen: clk-s-c0-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen";
-
-				clocks = <&clk_s_c0_pll0 0>,
-					 <&clk_s_c0_pll1 0>,
-					 <&clk_s_c0_quadfs 0>,
-					 <&clk_s_c0_quadfs 1>,
-					 <&clk_s_c0_quadfs 2>,
-					 <&clk_s_c0_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-icn-gpu",
-						     "clk-fdma",
-						     "clk-nand",
-						     "clk-hva",
-						     "clk-proc-stfe",
-						     "clk-proc-tp",
-						     "clk-rx-icn-dmu",
-						     "clk-rx-icn-hva",
-						     "clk-icn-cpu",
-						     "clk-tx-icn-dmu",
-						     "clk-mmc-0",
-						     "clk-mmc-1",
-						     "clk-jpegdec",
-						     "clk-ext2fa9",
-						     "clk-ic-bdisp-0",
-						     "clk-ic-bdisp-1",
-						     "clk-pp-dmu",
-						     "clk-vid-dmu",
-						     "clk-dss-lpc",
-						     "clk-st231-aud-0",
-						     "clk-st231-gp-1",
-						     "clk-st231-dmu",
-						     "clk-icn-lmi",
-						     "clk-tx-icn-disp-1",
-						     "clk-icn-sbc",
-						     "clk-stfe-frc2",
-						     "clk-eth-phy",
-						     "clk-eth-ref-phyclk",
-						     "clk-flash-promip",
-						     "clk-main-disp",
-						     "clk-aux-disp",
-						     "clk-compo-dvp",
-						     "clk-tx-icn-hades",
-						     "clk-rx-icn-hades",
-						     "clk-icn-reg-16",
-						     "clk-pp-hades",
-						     "clk-clust-hades",
-						     "clk-hwpe-hades",
-						     "clk-fc-hades";
-				clock-critical = <CLK_PROC_STFE>,
-						 <CLK_ICN_CPU>,
-						 <CLK_TX_ICN_DMU>,
-						 <CLK_EXT2F_A9>,
-						 <CLK_ICN_LMI>,
-						 <CLK_ICN_SBC>;
-
-				/*
-				 * ARM Peripheral clock for timers
-				 */
-				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
-					#clock-cells = <0>;
-					compatible = "fixed-factor-clock";
-
-					clocks = <&clk_s_c0_flexgen 13>;
-
-					clock-output-names = "clk-m-a9-ext2f-div2";
-
-					clock-div = <2>;
-					clock-mult = <1>;
-				};
-			};
-		};
-
-		clk_s_d0_quadfs: clk-s-d0-quadfs@9104000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9104000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d0-fs0-ch0",
-					     "clk-s-d0-fs0-ch1",
-					     "clk-s-d0-fs0-ch2",
-					     "clk-s-d0-fs0-ch3";
-		};
-
-		clockgen-d0@9104000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9104000 0x1000>;
-
-			clk_s_d0_flexgen: clk-s-d0-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen-audio", "st,flexgen";
-
-				clocks = <&clk_s_d0_quadfs 0>,
-					 <&clk_s_d0_quadfs 1>,
-					 <&clk_s_d0_quadfs 2>,
-					 <&clk_s_d0_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-pcm-0",
-						     "clk-pcm-1",
-						     "clk-pcm-2",
-						     "clk-spdiff",
-						     "clk-pcmr10-master",
-						     "clk-usb2-phy";
-			};
-		};
-
-		clk_s_d2_quadfs: clk-s-d2-quadfs@9106000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9106000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d2-fs0-ch0",
-					     "clk-s-d2-fs0-ch1",
-					     "clk-s-d2-fs0-ch2",
-					     "clk-s-d2-fs0-ch3";
-		};
-
-		clockgen-d2@9106000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9106000 0x1000>;
-
-			clk_s_d2_flexgen: clk-s-d2-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen-video", "st,flexgen";
-
-				clocks = <&clk_s_d2_quadfs 0>,
-					 <&clk_s_d2_quadfs 1>,
-					 <&clk_s_d2_quadfs 2>,
-					 <&clk_s_d2_quadfs 3>,
-					 <&clk_sysin>,
-					 <&clk_sysin>,
-					 <&clk_tmdsout_hdmi>;
-
-				clock-output-names = "clk-pix-main-disp",
-						     "clk-pix-pip",
-						     "clk-pix-gdp1",
-						     "clk-pix-gdp2",
-						     "clk-pix-gdp3",
-						     "clk-pix-gdp4",
-						     "clk-pix-aux-disp",
-						     "clk-denc",
-						     "clk-pix-hddac",
-						     "clk-hddac",
-						     "clk-sddac",
-						     "clk-pix-dvo",
-						     "clk-dvo",
-						     "clk-pix-hdmi",
-						     "clk-tmds-hdmi",
-						     "clk-ref-hdmiphy";
-						     };
-		};
-
-		clk_s_d3_quadfs: clk-s-d3-quadfs@9107000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9107000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d3-fs0-ch0",
-					     "clk-s-d3-fs0-ch1",
-					     "clk-s-d3-fs0-ch2",
-					     "clk-s-d3-fs0-ch3";
-		};
-
-		clockgen-d3@9107000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9107000 0x1000>;
-
-			clk_s_d3_flexgen: clk-s-d3-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen";
-
-				clocks = <&clk_s_d3_quadfs 0>,
-					 <&clk_s_d3_quadfs 1>,
-					 <&clk_s_d3_quadfs 2>,
-					 <&clk_s_d3_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-stfe-frc1",
-						     "clk-tsout-0",
-						     "clk-tsout-1",
-						     "clk-mchi",
-						     "clk-vsens-compo",
-						     "clk-frc1-remote",
-						     "clk-lpc-0",
-						     "clk-lpc-1";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stih418-clock.dtsi b/arch/arm/boot/dts/stih418-clock.dtsi
deleted file mode 100644
index 8fa092462102..000000000000
--- a/arch/arm/boot/dts/stih418-clock.dtsi
+++ /dev/null
@@ -1,334 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2015 STMicroelectronics R&D Limited
- */
-#include <dt-bindings/clock/stih418-clks.h>
-/ {
-	/*
-	 * Fixed 30MHz oscillator inputs to SoC
-	 */
-	clk_sysin: clk-sysin {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <30000000>;
-		clock-output-names = "CLK_SYSIN";
-	};
-
-	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		compatible = "st,stih418-clk", "simple-bus";
-
-		/*
-		 * A9 PLL.
-		 */
-		clockgen-a9@92b0000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x92b0000 0xffff>;
-
-			clockgen_a9_pll: clockgen-a9-pll {
-				#clock-cells = <1>;
-				compatible = "st,stih418-clkgen-plla9";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clockgen-a9-pll-odf";
-			};
-		};
-
-		/*
-		 * ARM CPU related clocks.
-		 */
-		clk_m_a9: clk-m-a9@92b0000 {
-			#clock-cells = <0>;
-			compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
-			reg = <0x92b0000 0x10000>;
-
-			clocks = <&clockgen_a9_pll 0>,
-				 <&clockgen_a9_pll 0>,
-				 <&clk_s_c0_flexgen 13>,
-				 <&clk_m_a9_ext2f_div2>;
-
-			/*
-			 * ARM Peripheral clock for timers
-			 */
-			arm_periph_clk: clk-m-a9-periphs {
-				#clock-cells = <0>;
-				compatible = "fixed-factor-clock";
-				clocks = <&clk_m_a9>;
-				clock-div = <2>;
-				clock-mult = <1>;
-			};
-		};
-
-		clockgen-a@90ff000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x90ff000 0x1000>;
-
-			clk_s_a0_pll: clk-s-a0-pll {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll0";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-a0-pll-ofd-0";
-			};
-
-			clk_s_a0_flexgen: clk-s-a0-flexgen {
-				compatible = "st,flexgen";
-
-				#clock-cells = <1>;
-
-				clocks = <&clk_s_a0_pll 0>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-ic-lmi0",
-						     "clk-ic-lmi1";
-			};
-		};
-
-		clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-pll";
-			reg = <0x9103000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-c0-fs0-ch0",
-					     "clk-s-c0-fs0-ch1",
-					     "clk-s-c0-fs0-ch2",
-					     "clk-s-c0-fs0-ch3";
-		};
-
-		clk_s_c0: clockgen-c@9103000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9103000 0x1000>;
-
-			clk_s_c0_pll0: clk-s-c0-pll0 {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll0";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-c0-pll0-odf-0";
-			};
-
-			clk_s_c0_pll1: clk-s-c0-pll1 {
-				#clock-cells = <1>;
-				compatible = "st,clkgen-pll1";
-
-				clocks = <&clk_sysin>;
-
-				clock-output-names = "clk-s-c0-pll1-odf-0";
-			};
-
-			clk_s_c0_flexgen: clk-s-c0-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen";
-
-				clocks = <&clk_s_c0_pll0 0>,
-					 <&clk_s_c0_pll1 0>,
-					 <&clk_s_c0_quadfs 0>,
-					 <&clk_s_c0_quadfs 1>,
-					 <&clk_s_c0_quadfs 2>,
-					 <&clk_s_c0_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-icn-gpu",
-						     "clk-fdma",
-						     "clk-nand",
-						     "clk-hva",
-						     "clk-proc-stfe",
-						     "clk-tp",
-						     "clk-rx-icn-dmu",
-						     "clk-rx-icn-hva",
-						     "clk-icn-cpu",
-						     "clk-tx-icn-dmu",
-						     "clk-mmc-0",
-						     "clk-mmc-1",
-						     "clk-jpegdec",
-						     "clk-icn-reg",
-						     "clk-proc-bdisp-0",
-						     "clk-proc-bdisp-1",
-						     "clk-pp-dmu",
-						     "clk-vid-dmu",
-						     "clk-dss-lpc",
-						     "clk-st231-aud-0",
-						     "clk-st231-gp-1",
-						     "clk-st231-dmu",
-						     "clk-icn-lmi",
-						     "clk-tx-icn-1",
-						     "clk-icn-sbc",
-						     "clk-stfe-frc2",
-						     "clk-eth-phyref",
-						     "clk-eth-ref-phyclk",
-						     "clk-flash-promip",
-						     "clk-main-disp",
-						     "clk-aux-disp",
-						     "clk-compo-dvp",
-						     "clk-tx-icn-hades",
-						     "clk-rx-icn-hades",
-						     "clk-icn-reg-16",
-						     "clk-pp-hevc",
-						     "clk-clust-hevc",
-						     "clk-hwpe-hevc",
-						     "clk-fc-hevc",
-						     "clk-proc-mixer",
-						     "clk-proc-sc",
-						     "clk-avsp-hevc";
-
-				/*
-				 * ARM Peripheral clock for timers
-				 */
-				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
-					#clock-cells = <0>;
-					compatible = "fixed-factor-clock";
-
-					clocks = <&clk_s_c0_flexgen 13>;
-
-					clock-output-names = "clk-m-a9-ext2f-div2";
-
-					clock-div = <2>;
-					clock-mult = <1>;
-				};
-			};
-		};
-
-		clk_s_d0_quadfs: clk-s-d0-quadfs@9104000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9104000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d0-fs0-ch0",
-					     "clk-s-d0-fs0-ch1",
-					     "clk-s-d0-fs0-ch2",
-					     "clk-s-d0-fs0-ch3";
-		};
-
-		clockgen-d0@9104000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9104000 0x1000>;
-
-			clk_s_d0_flexgen: clk-s-d0-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen-audio", "st,flexgen";
-
-				clocks = <&clk_s_d0_quadfs 0>,
-					 <&clk_s_d0_quadfs 1>,
-					 <&clk_s_d0_quadfs 2>,
-					 <&clk_s_d0_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-pcm-0",
-						     "clk-pcm-1",
-						     "clk-pcm-2",
-						     "clk-spdiff",
-						     "clk-pcmr10-master",
-						     "clk-usb2-phy";
-			};
-		};
-
-		clk_s_d2_quadfs: clk-s-d2-quadfs@9106000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9106000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d2-fs0-ch0",
-					     "clk-s-d2-fs0-ch1",
-					     "clk-s-d2-fs0-ch2",
-					     "clk-s-d2-fs0-ch3";
-		};
-
-		clockgen-d2@9106000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9106000 0x1000>;
-
-			clk_s_d2_flexgen: clk-s-d2-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen-video", "st,flexgen";
-
-				clocks = <&clk_s_d2_quadfs 0>,
-					 <&clk_s_d2_quadfs 1>,
-					 <&clk_s_d2_quadfs 2>,
-					 <&clk_s_d2_quadfs 3>,
-					 <&clk_sysin>,
-					 <&clk_sysin>,
-					 <&clk_tmdsout_hdmi>;
-
-				clock-output-names = "clk-pix-main-disp",
-						     "",
-						     "",
-						     "",
-						     "",
-						     "clk-tmds-hdmi-div2",
-						     "clk-pix-aux-disp",
-						     "clk-denc",
-						     "clk-pix-hddac",
-						     "clk-hddac",
-						     "clk-sddac",
-						     "clk-pix-dvo",
-						     "clk-dvo",
-						     "clk-pix-hdmi",
-						     "clk-tmds-hdmi",
-						     "clk-ref-hdmiphy",
-						     "", "", "", "", "",
-						     "", "", "", "", "",
-						     "", "", "", "", "",
-						     "", "", "", "", "",
-						     "", "", "", "", "",
-						     "", "", "", "", "",
-						     "", "clk-vp9";
-			};
-		};
-
-		clk_s_d3_quadfs: clk-s-d3-quadfs@9107000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs";
-			reg = <0x9107000 0x1000>;
-
-			clocks = <&clk_sysin>;
-
-			clock-output-names = "clk-s-d3-fs0-ch0",
-					     "clk-s-d3-fs0-ch1",
-					     "clk-s-d3-fs0-ch2",
-					     "clk-s-d3-fs0-ch3";
-		};
-
-		clockgen-d3@9107000 {
-			compatible = "st,clkgen-c32";
-			reg = <0x9107000 0x1000>;
-
-			clk_s_d3_flexgen: clk-s-d3-flexgen {
-				#clock-cells = <1>;
-				compatible = "st,flexgen";
-
-				clocks = <&clk_s_d3_quadfs 0>,
-					 <&clk_s_d3_quadfs 1>,
-					 <&clk_s_d3_quadfs 2>,
-					 <&clk_s_d3_quadfs 3>,
-					 <&clk_sysin>;
-
-				clock-output-names = "clk-stfe-frc1",
-						     "clk-tsout-0",
-						     "clk-tsout-1",
-						     "clk-mchi",
-						     "clk-vsens-compo",
-						     "clk-frc1-remote",
-						     "clk-lpc-0",
-						     "clk-lpc-1";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stm32f746-pinctrl.dtsi b/arch/arm/boot/dts/stm32f746-pinctrl.dtsi
deleted file mode 100644
index fcfd2ac7239b..000000000000
--- a/arch/arm/boot/dts/stm32f746-pinctrl.dtsi
+++ /dev/null
@@ -1,11 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
- * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
- */
-
-#include "stm32f7-pinctrl.dtsi"
-
-&pinctrl{
-	compatible = "st,stm32f746-pinctrl";
-};
diff --git a/arch/arm/boot/dts/stm32f769-pinctrl.dtsi b/arch/arm/boot/dts/stm32f769-pinctrl.dtsi
deleted file mode 100644
index 31005dd9929c..000000000000
--- a/arch/arm/boot/dts/stm32f769-pinctrl.dtsi
+++ /dev/null
@@ -1,11 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
- * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
- */
-
-#include "stm32f7-pinctrl.dtsi"
-
-&pinctrl{
-	compatible = "st,stm32f769-pinctrl";
-};
diff --git a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
deleted file mode 100644
index e44e7baa3f17..000000000000
--- a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
+++ /dev/null
@@ -1,306 +0,0 @@
-/*
- * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/pinctrl/stm32-pinfunc.h>
-
-/ {
-	soc {
-		pin-controller {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "st,stm32h743-pinctrl";
-			ranges = <0 0x58020000 0x3000>;
-			interrupt-parent = <&exti>;
-			st,syscfg = <&syscfg 0x8>;
-			pins-are-numbered;
-
-			gpioa: gpio@58020000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x0 0x400>;
-				clocks = <&rcc GPIOA_CK>;
-				st,bank-name = "GPIOA";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpiob: gpio@58020400 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x400 0x400>;
-				clocks = <&rcc GPIOB_CK>;
-				st,bank-name = "GPIOB";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpioc: gpio@58020800 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x800 0x400>;
-				clocks = <&rcc GPIOC_CK>;
-				st,bank-name = "GPIOC";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpiod: gpio@58020c00 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0xc00 0x400>;
-				clocks = <&rcc GPIOD_CK>;
-				st,bank-name = "GPIOD";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpioe: gpio@58021000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x1000 0x400>;
-				clocks = <&rcc GPIOE_CK>;
-				st,bank-name = "GPIOE";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpiof: gpio@58021400 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x1400 0x400>;
-				clocks = <&rcc GPIOF_CK>;
-				st,bank-name = "GPIOF";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpiog: gpio@58021800 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x1800 0x400>;
-				clocks = <&rcc GPIOG_CK>;
-				st,bank-name = "GPIOG";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpioh: gpio@58021c00 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x1c00 0x400>;
-				clocks = <&rcc GPIOH_CK>;
-				st,bank-name = "GPIOH";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpioi: gpio@58022000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x2000 0x400>;
-				clocks = <&rcc GPIOI_CK>;
-				st,bank-name = "GPIOI";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpioj: gpio@58022400 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x2400 0x400>;
-				clocks = <&rcc GPIOJ_CK>;
-				st,bank-name = "GPIOJ";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpiok: gpio@58022800 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x2800 0x400>;
-				clocks = <&rcc GPIOK_CK>;
-				st,bank-name = "GPIOK";
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			i2c1_pins_a: i2c1@0 {
-				pins {
-					pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
-						 <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			ethernet_rmii: rmii@0 {
-				pins {
-					pinmux = <STM32_PINMUX('G', 11, AF11)>,
-						 <STM32_PINMUX('G', 13, AF11)>,
-						 <STM32_PINMUX('G', 12, AF11)>,
-						 <STM32_PINMUX('C', 4, AF11)>,
-						 <STM32_PINMUX('C', 5, AF11)>,
-						 <STM32_PINMUX('A', 7, AF11)>,
-						 <STM32_PINMUX('C', 1, AF11)>,
-						 <STM32_PINMUX('A', 2, AF11)>,
-						 <STM32_PINMUX('A', 1, AF11)>;
-					slew-rate = <2>;
-				};
-			};
-
-			sdmmc1_b4_pins_a: sdmmc1-b4-0 {
-				pins {
-					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
-						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
-						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
-						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
-						 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
-						 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
-					slew-rate = <3>;
-					drive-push-pull;
-					bias-disable;
-				};
-			};
-
-			sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
-						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
-						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
-						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
-						 <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
-					slew-rate = <3>;
-					drive-push-pull;
-					bias-disable;
-				};
-				pins2{
-					pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
-					slew-rate = <3>;
-					drive-open-drain;
-					bias-disable;
-				};
-			};
-
-			sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
-						 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
-						 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
-						 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
-						 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
-						 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
-				};
-			};
-
-			sdmmc1_dir_pins_a: sdmmc1-dir-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
-						 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
-						 <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
-					slew-rate = <3>;
-					drive-push-pull;
-					bias-pull-up;
-				};
-				pins2{
-					pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
-					bias-pull-up;
-				};
-			};
-
-			sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
-						 <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
-						 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
-						 <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
-				};
-			};
-
-			usart1_pins: usart1@0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
-					bias-disable;
-				};
-			};
-
-			usart2_pins: usart2@0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
-					bias-disable;
-				};
-			};
-
-			usbotg_hs_pins_a: usbotg-hs@0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 4, AF10)>,	/* ULPI_NXT */
-							 <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
-							 <STM32_PINMUX('C', 0, AF10)>,	/* ULPI_STP> */
-							 <STM32_PINMUX('A', 5, AF10)>,	/* ULPI_CK> */
-							 <STM32_PINMUX('A', 3, AF10)>,	/* ULPI_D0> */
-							 <STM32_PINMUX('B', 0, AF10)>,	/* ULPI_D1> */
-							 <STM32_PINMUX('B', 1, AF10)>,	/* ULPI_D2> */
-							 <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
-							 <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
-							 <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
-							 <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
-							 <STM32_PINMUX('B', 5, AF10)>;	/* ULPI_D7> */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <2>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
deleted file mode 100644
index 3d1ecb408b03..000000000000
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ /dev/null
@@ -1,953 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
- * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
- */
-#include <dt-bindings/pinctrl/stm32-pinfunc.h>
-
-/ {
-	soc {
-		pinctrl: pin-controller@50002000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "st,stm32mp157-pinctrl";
-			ranges = <0 0x50002000 0xa400>;
-			interrupt-parent = <&exti>;
-			st,syscfg = <&exti 0x60 0xff>;
-			pins-are-numbered;
-
-			gpioa: gpio@50002000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x0 0x400>;
-				clocks = <&rcc GPIOA>;
-				st,bank-name = "GPIOA";
-				status = "disabled";
-			};
-
-			gpiob: gpio@50003000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x1000 0x400>;
-				clocks = <&rcc GPIOB>;
-				st,bank-name = "GPIOB";
-				status = "disabled";
-			};
-
-			gpioc: gpio@50004000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x2000 0x400>;
-				clocks = <&rcc GPIOC>;
-				st,bank-name = "GPIOC";
-				status = "disabled";
-			};
-
-			gpiod: gpio@50005000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x3000 0x400>;
-				clocks = <&rcc GPIOD>;
-				st,bank-name = "GPIOD";
-				status = "disabled";
-			};
-
-			gpioe: gpio@50006000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x4000 0x400>;
-				clocks = <&rcc GPIOE>;
-				st,bank-name = "GPIOE";
-				status = "disabled";
-			};
-
-			gpiof: gpio@50007000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x5000 0x400>;
-				clocks = <&rcc GPIOF>;
-				st,bank-name = "GPIOF";
-				status = "disabled";
-			};
-
-			gpiog: gpio@50008000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x6000 0x400>;
-				clocks = <&rcc GPIOG>;
-				st,bank-name = "GPIOG";
-				status = "disabled";
-			};
-
-			gpioh: gpio@50009000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x7000 0x400>;
-				clocks = <&rcc GPIOH>;
-				st,bank-name = "GPIOH";
-				status = "disabled";
-			};
-
-			gpioi: gpio@5000a000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x8000 0x400>;
-				clocks = <&rcc GPIOI>;
-				st,bank-name = "GPIOI";
-				status = "disabled";
-			};
-
-			gpioj: gpio@5000b000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x9000 0x400>;
-				clocks = <&rcc GPIOJ>;
-				st,bank-name = "GPIOJ";
-				status = "disabled";
-			};
-
-			gpiok: gpio@5000c000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0xa000 0x400>;
-				clocks = <&rcc GPIOK>;
-				st,bank-name = "GPIOK";
-				status = "disabled";
-			};
-
-			adc12_ain_pins_a: adc12-ain-0 {
-				pins {
-					pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1 in13 */
-						 <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
-						 <STM32_PINMUX('F', 13, ANALOG)>, /* ADC2 in2 */
-						 <STM32_PINMUX('F', 14, ANALOG)>; /* ADC2 in6 */
-				};
-			};
-
-			adc12_usb_cc_pins_a: adc12-usb-cc-pins-0 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* ADC12 in18 */
-						 <STM32_PINMUX('A', 5, ANALOG)>; /* ADC12 in19 */
-				};
-			};
-
-			cec_pins_a: cec-0 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 15, AF4)>;
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			cec_pins_sleep_a: cec-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 15, ANALOG)>; /* HDMI_CEC */
-				};
-			};
-
-			cec_pins_b: cec-1 {
-				pins {
-					pinmux = <STM32_PINMUX('B', 6, AF5)>;
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			cec_pins_sleep_b: cec-sleep-1 {
-				pins {
-					pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* HDMI_CEC */
-				};
-			};
-
-			dac_ch1_pins_a: dac-ch1 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 4, ANALOG)>;
-				};
-			};
-
-			dac_ch2_pins_a: dac-ch2 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 5, ANALOG)>;
-				};
-			};
-
-			dcmi_pins_a: dcmi-0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 8,  AF13)>,/* DCMI_HSYNC */
-						 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
-						 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
-						 <STM32_PINMUX('H', 9,  AF13)>,/* DCMI_D0 */
-						 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
-						 <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
-						 <STM32_PINMUX('H', 12, AF13)>,/* DCMI_D3 */
-						 <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */
-						 <STM32_PINMUX('I', 4,  AF13)>,/* DCMI_D5 */
-						 <STM32_PINMUX('B', 8,  AF13)>,/* DCMI_D6 */
-						 <STM32_PINMUX('E', 6,  AF13)>,/* DCMI_D7 */
-						 <STM32_PINMUX('I', 1,  AF13)>,/* DCMI_D8 */
-						 <STM32_PINMUX('H', 7,  AF13)>,/* DCMI_D9 */
-						 <STM32_PINMUX('I', 3,  AF13)>,/* DCMI_D10 */
-						 <STM32_PINMUX('H', 15, AF13)>;/* DCMI_D11 */
-					bias-disable;
-				};
-			};
-
-			dcmi_sleep_pins_a: dcmi-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 8,  ANALOG)>,/* DCMI_HSYNC */
-						 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
-						 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
-						 <STM32_PINMUX('H', 9,  ANALOG)>,/* DCMI_D0 */
-						 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
-						 <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
-						 <STM32_PINMUX('H', 12, ANALOG)>,/* DCMI_D3 */
-						 <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */
-						 <STM32_PINMUX('I', 4,  ANALOG)>,/* DCMI_D5 */
-						 <STM32_PINMUX('B', 8,  ANALOG)>,/* DCMI_D6 */
-						 <STM32_PINMUX('E', 6,  ANALOG)>,/* DCMI_D7 */
-						 <STM32_PINMUX('I', 1,  ANALOG)>,/* DCMI_D8 */
-						 <STM32_PINMUX('H', 7,  ANALOG)>,/* DCMI_D9 */
-						 <STM32_PINMUX('I', 3,  ANALOG)>,/* DCMI_D10 */
-						 <STM32_PINMUX('H', 15, ANALOG)>;/* DCMI_D11 */
-				};
-			};
-
-			ethernet0_rgmii_pins_a: rgmii-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
-						 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
-						 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
-						 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
-						 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
-						 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
-						 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
-						 <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */
-						 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <3>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
-						 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
-						 <STM32_PINMUX('B', 0, AF11)>, /* ETH_RGMII_RXD2 */
-						 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
-						 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
-						 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
-					bias-disable;
-				};
-			};
-
-			ethernet0_rgmii_pins_sleep_a: rgmii-sleep-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
-						 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
-						 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
-						 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
-						 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
-						 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
-						 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
-						 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
-						 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
-						 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
-						 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
-						 <STM32_PINMUX('B', 0, ANALOG)>, /* ETH_RGMII_RXD2 */
-						 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
-						 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
-						 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
-				};
-			};
-
-			fmc_pins_a: fmc-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
-						 <STM32_PINMUX('D', 5, AF12)>, /* FMC_NWE */
-						 <STM32_PINMUX('D', 11, AF12)>, /* FMC_A16_FMC_CLE */
-						 <STM32_PINMUX('D', 12, AF12)>, /* FMC_A17_FMC_ALE */
-						 <STM32_PINMUX('D', 14, AF12)>, /* FMC_D0 */
-						 <STM32_PINMUX('D', 15, AF12)>, /* FMC_D1 */
-						 <STM32_PINMUX('D', 0, AF12)>, /* FMC_D2 */
-						 <STM32_PINMUX('D', 1, AF12)>, /* FMC_D3 */
-						 <STM32_PINMUX('E', 7, AF12)>, /* FMC_D4 */
-						 <STM32_PINMUX('E', 8, AF12)>, /* FMC_D5 */
-						 <STM32_PINMUX('E', 9, AF12)>, /* FMC_D6 */
-						 <STM32_PINMUX('E', 10, AF12)>, /* FMC_D7 */
-						 <STM32_PINMUX('G', 9, AF12)>; /* FMC_NE2_FMC_NCE */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('D', 6, AF12)>; /* FMC_NWAIT */
-					bias-pull-up;
-				};
-			};
-
-			fmc_sleep_pins_a: fmc-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('D', 4, ANALOG)>, /* FMC_NOE */
-						 <STM32_PINMUX('D', 5, ANALOG)>, /* FMC_NWE */
-						 <STM32_PINMUX('D', 11, ANALOG)>, /* FMC_A16_FMC_CLE */
-						 <STM32_PINMUX('D', 12, ANALOG)>, /* FMC_A17_FMC_ALE */
-						 <STM32_PINMUX('D', 14, ANALOG)>, /* FMC_D0 */
-						 <STM32_PINMUX('D', 15, ANALOG)>, /* FMC_D1 */
-						 <STM32_PINMUX('D', 0, ANALOG)>, /* FMC_D2 */
-						 <STM32_PINMUX('D', 1, ANALOG)>, /* FMC_D3 */
-						 <STM32_PINMUX('E', 7, ANALOG)>, /* FMC_D4 */
-						 <STM32_PINMUX('E', 8, ANALOG)>, /* FMC_D5 */
-						 <STM32_PINMUX('E', 9, ANALOG)>, /* FMC_D6 */
-						 <STM32_PINMUX('E', 10, ANALOG)>, /* FMC_D7 */
-						 <STM32_PINMUX('D', 6, ANALOG)>, /* FMC_NWAIT */
-						 <STM32_PINMUX('G', 9, ANALOG)>; /* FMC_NE2_FMC_NCE */
-				};
-			};
-
-			i2c1_pins_a: i2c1-0 {
-				pins {
-					pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
-						 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c1_pins_sleep_a: i2c1-1 {
-				pins {
-					pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
-						 <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */
-				};
-			};
-
-			i2c1_pins_b: i2c1-2 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */
-						 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c1_pins_sleep_b: i2c1-3 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */
-						 <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */
-				};
-			};
-
-			i2c2_pins_a: i2c2-0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
-						 <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c2_pins_sleep_a: i2c2-1 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 4, ANALOG)>, /* I2C2_SCL */
-						 <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
-				};
-			};
-
-			i2c2_pins_b1: i2c2-2 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c2_pins_sleep_b1: i2c2-3 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
-				};
-			};
-
-			i2c5_pins_a: i2c5-0 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */
-						 <STM32_PINMUX('A', 12, AF4)>; /* I2C5_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c5_pins_sleep_a: i2c5-1 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* I2C5_SCL */
-						 <STM32_PINMUX('A', 12, ANALOG)>; /* I2C5_SDA */
-
-				};
-			};
-
-			i2s2_pins_a: i2s2-0 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 3, AF5)>, /* I2S2_SDO */
-						 <STM32_PINMUX('B', 9, AF5)>, /* I2S2_WS */
-						 <STM32_PINMUX('A', 9, AF5)>; /* I2S2_CK */
-					slew-rate = <1>;
-					drive-push-pull;
-					bias-disable;
-				};
-			};
-
-			i2s2_pins_sleep_a: i2s2-1 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 3, ANALOG)>, /* I2S2_SDO */
-						 <STM32_PINMUX('B', 9, ANALOG)>, /* I2S2_WS */
-						 <STM32_PINMUX('A', 9, ANALOG)>; /* I2S2_CK */
-				};
-			};
-
-			ltdc_pins_a: ltdc-a-0 {
-				pins {
-					pinmux = <STM32_PINMUX('G',  7, AF14)>, /* LCD_CLK */
-						 <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */
-						 <STM32_PINMUX('I',  9, AF14)>, /* LCD_VSYNC */
-						 <STM32_PINMUX('F', 10, AF14)>, /* LCD_DE */
-						 <STM32_PINMUX('H',  2, AF14)>, /* LCD_R0 */
-						 <STM32_PINMUX('H',  3, AF14)>, /* LCD_R1 */
-						 <STM32_PINMUX('H',  8, AF14)>, /* LCD_R2 */
-						 <STM32_PINMUX('H',  9, AF14)>, /* LCD_R3 */
-						 <STM32_PINMUX('H', 10, AF14)>, /* LCD_R4 */
-						 <STM32_PINMUX('C',  0, AF14)>, /* LCD_R5 */
-						 <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */
-						 <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */
-						 <STM32_PINMUX('E',  5, AF14)>, /* LCD_G0 */
-						 <STM32_PINMUX('E',  6, AF14)>, /* LCD_G1 */
-						 <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
-						 <STM32_PINMUX('H', 14, AF14)>, /* LCD_G3 */
-						 <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */
-						 <STM32_PINMUX('I',  0, AF14)>, /* LCD_G5 */
-						 <STM32_PINMUX('I',  1, AF14)>, /* LCD_G6 */
-						 <STM32_PINMUX('I',  2, AF14)>, /* LCD_G7 */
-						 <STM32_PINMUX('D',  9, AF14)>, /* LCD_B0 */
-						 <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */
-						 <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */
-						 <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */
-						 <STM32_PINMUX('I',  4, AF14)>, /* LCD_B4 */
-						 <STM32_PINMUX('A',  3, AF14)>, /* LCD_B5 */
-						 <STM32_PINMUX('B',  8, AF14)>, /* LCD_B6 */
-						 <STM32_PINMUX('D',  8, AF14)>; /* LCD_B7 */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-			};
-
-			ltdc_pins_sleep_a: ltdc-a-1 {
-				pins {
-					pinmux = <STM32_PINMUX('G',  7, ANALOG)>, /* LCD_CLK */
-						 <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */
-						 <STM32_PINMUX('I',  9, ANALOG)>, /* LCD_VSYNC */
-						 <STM32_PINMUX('F', 10, ANALOG)>, /* LCD_DE */
-						 <STM32_PINMUX('H',  2, ANALOG)>, /* LCD_R0 */
-						 <STM32_PINMUX('H',  3, ANALOG)>, /* LCD_R1 */
-						 <STM32_PINMUX('H',  8, ANALOG)>, /* LCD_R2 */
-						 <STM32_PINMUX('H',  9, ANALOG)>, /* LCD_R3 */
-						 <STM32_PINMUX('H', 10, ANALOG)>, /* LCD_R4 */
-						 <STM32_PINMUX('C',  0, ANALOG)>, /* LCD_R5 */
-						 <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */
-						 <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */
-						 <STM32_PINMUX('E',  5, ANALOG)>, /* LCD_G0 */
-						 <STM32_PINMUX('E',  6, ANALOG)>, /* LCD_G1 */
-						 <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
-						 <STM32_PINMUX('H', 14, ANALOG)>, /* LCD_G3 */
-						 <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */
-						 <STM32_PINMUX('I',  0, ANALOG)>, /* LCD_G5 */
-						 <STM32_PINMUX('I',  1, ANALOG)>, /* LCD_G6 */
-						 <STM32_PINMUX('I',  2, ANALOG)>, /* LCD_G7 */
-						 <STM32_PINMUX('D',  9, ANALOG)>, /* LCD_B0 */
-						 <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */
-						 <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */
-						 <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */
-						 <STM32_PINMUX('I',  4, ANALOG)>, /* LCD_B4 */
-						 <STM32_PINMUX('A',  3, ANALOG)>, /* LCD_B5 */
-						 <STM32_PINMUX('B',  8, ANALOG)>, /* LCD_B6 */
-						 <STM32_PINMUX('D',  8, ANALOG)>; /* LCD_B7 */
-				};
-			};
-
-			ltdc_pins_b: ltdc-b-0 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 14, AF14)>, /* LCD_CLK */
-						 <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */
-						 <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */
-						 <STM32_PINMUX('K',  7, AF14)>, /* LCD_DE */
-						 <STM32_PINMUX('I', 15, AF14)>, /* LCD_R0 */
-						 <STM32_PINMUX('J',  0, AF14)>, /* LCD_R1 */
-						 <STM32_PINMUX('J',  1, AF14)>, /* LCD_R2 */
-						 <STM32_PINMUX('J',  2, AF14)>, /* LCD_R3 */
-						 <STM32_PINMUX('J',  3, AF14)>, /* LCD_R4 */
-						 <STM32_PINMUX('J',  4, AF14)>, /* LCD_R5 */
-						 <STM32_PINMUX('J',  5, AF14)>, /* LCD_R6 */
-						 <STM32_PINMUX('J',  6, AF14)>, /* LCD_R7 */
-						 <STM32_PINMUX('J',  7, AF14)>, /* LCD_G0 */
-						 <STM32_PINMUX('J',  8, AF14)>, /* LCD_G1 */
-						 <STM32_PINMUX('J',  9, AF14)>, /* LCD_G2 */
-						 <STM32_PINMUX('J', 10, AF14)>, /* LCD_G3 */
-						 <STM32_PINMUX('J', 11, AF14)>, /* LCD_G4 */
-						 <STM32_PINMUX('K',  0, AF14)>, /* LCD_G5 */
-						 <STM32_PINMUX('K',  1, AF14)>, /* LCD_G6 */
-						 <STM32_PINMUX('K',  2, AF14)>, /* LCD_G7 */
-						 <STM32_PINMUX('J', 12, AF14)>, /* LCD_B0 */
-						 <STM32_PINMUX('J', 13, AF14)>, /* LCD_B1 */
-						 <STM32_PINMUX('J', 14, AF14)>, /* LCD_B2 */
-						 <STM32_PINMUX('J', 15, AF14)>, /* LCD_B3 */
-						 <STM32_PINMUX('K',  3, AF14)>, /* LCD_B4 */
-						 <STM32_PINMUX('K',  4, AF14)>, /* LCD_B5 */
-						 <STM32_PINMUX('K',  5, AF14)>, /* LCD_B6 */
-						 <STM32_PINMUX('K',  6, AF14)>; /* LCD_B7 */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-			};
-
-			ltdc_pins_sleep_b: ltdc-b-1 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 14, ANALOG)>, /* LCD_CLK */
-						 <STM32_PINMUX('I', 12, ANALOG)>, /* LCD_HSYNC */
-						 <STM32_PINMUX('I', 13, ANALOG)>, /* LCD_VSYNC */
-						 <STM32_PINMUX('K',  7, ANALOG)>, /* LCD_DE */
-						 <STM32_PINMUX('I', 15, ANALOG)>, /* LCD_R0 */
-						 <STM32_PINMUX('J',  0, ANALOG)>, /* LCD_R1 */
-						 <STM32_PINMUX('J',  1, ANALOG)>, /* LCD_R2 */
-						 <STM32_PINMUX('J',  2, ANALOG)>, /* LCD_R3 */
-						 <STM32_PINMUX('J',  3, ANALOG)>, /* LCD_R4 */
-						 <STM32_PINMUX('J',  4, ANALOG)>, /* LCD_R5 */
-						 <STM32_PINMUX('J',  5, ANALOG)>, /* LCD_R6 */
-						 <STM32_PINMUX('J',  6, ANALOG)>, /* LCD_R7 */
-						 <STM32_PINMUX('J',  7, ANALOG)>, /* LCD_G0 */
-						 <STM32_PINMUX('J',  8, ANALOG)>, /* LCD_G1 */
-						 <STM32_PINMUX('J',  9, ANALOG)>, /* LCD_G2 */
-						 <STM32_PINMUX('J', 10, ANALOG)>, /* LCD_G3 */
-						 <STM32_PINMUX('J', 11, ANALOG)>, /* LCD_G4 */
-						 <STM32_PINMUX('K',  0, ANALOG)>, /* LCD_G5 */
-						 <STM32_PINMUX('K',  1, ANALOG)>, /* LCD_G6 */
-						 <STM32_PINMUX('K',  2, ANALOG)>, /* LCD_G7 */
-						 <STM32_PINMUX('J', 12, ANALOG)>, /* LCD_B0 */
-						 <STM32_PINMUX('J', 13, ANALOG)>, /* LCD_B1 */
-						 <STM32_PINMUX('J', 14, ANALOG)>, /* LCD_B2 */
-						 <STM32_PINMUX('J', 15, ANALOG)>, /* LCD_B3 */
-						 <STM32_PINMUX('K',  3, ANALOG)>, /* LCD_B4 */
-						 <STM32_PINMUX('K',  4, ANALOG)>, /* LCD_B5 */
-						 <STM32_PINMUX('K',  5, ANALOG)>, /* LCD_B6 */
-						 <STM32_PINMUX('K',  6, ANALOG)>; /* LCD_B7 */
-				};
-			};
-
-			m_can1_pins_a: m-can1-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
-					slew-rate = <1>;
-					drive-push-pull;
-					bias-disable;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('I', 9, AF9)>; /* CAN1_RX */
-					bias-disable;
-				};
-			};
-
-			m_can1_sleep_pins_a: m_can1-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
-						 <STM32_PINMUX('I', 9, ANALOG)>; /* CAN1_RX */
-				};
-			};
-
-			pwm2_pins_a: pwm2-0 {
-				pins {
-					pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
-					bias-pull-down;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-			};
-
-			pwm8_pins_a: pwm8-0 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */
-					bias-pull-down;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-			};
-
-			pwm12_pins_a: pwm12-0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */
-					bias-pull-down;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-			};
-
-			qspi_clk_pins_a: qspi-clk-0 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <3>;
-				};
-			};
-
-			qspi_clk_sleep_pins_a: qspi-clk-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 10, ANALOG)>; /* QSPI_CLK */
-				};
-			};
-
-			qspi_bk1_pins_a: qspi-bk1-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
-						 <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
-						 <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
-						 <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
-					bias-pull-up;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-			};
-
-			qspi_bk1_sleep_pins_a: qspi-bk1-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* QSPI_BK1_IO0 */
-						 <STM32_PINMUX('F', 9, ANALOG)>, /* QSPI_BK1_IO1 */
-						 <STM32_PINMUX('F', 7, ANALOG)>, /* QSPI_BK1_IO2 */
-						 <STM32_PINMUX('F', 6, ANALOG)>, /* QSPI_BK1_IO3 */
-						 <STM32_PINMUX('B', 6, ANALOG)>; /* QSPI_BK1_NCS */
-				};
-			};
-
-			qspi_bk2_pins_a: qspi-bk2-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
-						 <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
-						 <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
-						 <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
-					bias-pull-up;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-			};
-
-			qspi_bk2_sleep_pins_a: qspi-bk2-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* QSPI_BK2_IO0 */
-						 <STM32_PINMUX('H', 3, ANALOG)>, /* QSPI_BK2_IO1 */
-						 <STM32_PINMUX('G', 10, ANALOG)>, /* QSPI_BK2_IO2 */
-						 <STM32_PINMUX('G', 7, ANALOG)>, /* QSPI_BK2_IO3 */
-						 <STM32_PINMUX('C', 0, ANALOG)>; /* QSPI_BK2_NCS */
-				};
-			};
-
-			sai2a_pins_a: sai2a-0 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 5, AF10)>, /* SAI2_SCK_A */
-						 <STM32_PINMUX('I', 6, AF10)>, /* SAI2_SD_A */
-						 <STM32_PINMUX('I', 7, AF10)>, /* SAI2_FS_A */
-						 <STM32_PINMUX('E', 0, AF10)>; /* SAI2_MCLK_A */
-					slew-rate = <0>;
-					drive-push-pull;
-					bias-disable;
-				};
-			};
-
-			sai2a_sleep_pins_a: sai2a-1 {
-				pins {
-					pinmux = <STM32_PINMUX('I', 5, ANALOG)>, /* SAI2_SCK_A */
-						 <STM32_PINMUX('I', 6, ANALOG)>, /* SAI2_SD_A */
-						 <STM32_PINMUX('I', 7, ANALOG)>, /* SAI2_FS_A */
-						 <STM32_PINMUX('E', 0, ANALOG)>; /* SAI2_MCLK_A */
-				};
-			};
-
-			sai2b_pins_a: sai2b-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */
-						 <STM32_PINMUX('E', 13, AF10)>, /* SAI2_FS_B */
-						 <STM32_PINMUX('E', 14, AF10)>; /* SAI2_MCLK_B */
-					slew-rate = <0>;
-					drive-push-pull;
-					bias-disable;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
-					bias-disable;
-				};
-			};
-
-			sai2b_sleep_pins_a: sai2b-1 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* SAI2_SD_B */
-						 <STM32_PINMUX('E', 12, ANALOG)>, /* SAI2_SCK_B */
-						 <STM32_PINMUX('E', 13, ANALOG)>, /* SAI2_FS_B */
-						 <STM32_PINMUX('E', 14, ANALOG)>; /* SAI2_MCLK_B */
-				};
-			};
-
-			sai2b_pins_b: sai2b-2 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
-					bias-disable;
-				};
-			};
-
-			sai2b_sleep_pins_b: sai2b-3 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
-				};
-			};
-
-			sai4a_pins_a: sai4a-0 {
-				pins {
-					pinmux = <STM32_PINMUX('B', 5, AF10)>; /* SAI4_SD_A */
-					slew-rate = <0>;
-					drive-push-pull;
-					bias-disable;
-				};
-			};
-
-			sai4a_sleep_pins_a: sai4a-1 {
-				pins {
-					pinmux = <STM32_PINMUX('B', 5, ANALOG)>; /* SAI4_SD_A */
-				};
-			};
-
-			sdmmc1_b4_pins_a: sdmmc1-b4-0 {
-				pins {
-					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
-						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
-						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
-						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
-						 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
-						 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
-					slew-rate = <3>;
-					drive-push-pull;
-					bias-disable;
-				};
-			};
-
-			sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
-						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
-						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
-						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
-						 <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
-					slew-rate = <3>;
-					drive-push-pull;
-					bias-disable;
-				};
-				pins2{
-					pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
-					slew-rate = <3>;
-					drive-open-drain;
-					bias-disable;
-				};
-			};
-
-			sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
-						 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
-						 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
-						 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
-						 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
-						 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
-				};
-			};
-
-			sdmmc1_dir_pins_a: sdmmc1-dir-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
-						 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
-						 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
-					slew-rate = <3>;
-					drive-push-pull;
-					bias-pull-up;
-				};
-				pins2{
-					pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
-					bias-pull-up;
-				};
-			};
-
-			sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
-				pins {
-					pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
-						 <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
-						 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
-						 <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
-				};
-			};
-
-			spdifrx_pins_a: spdifrx-0 {
-				pins {
-					pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
-					bias-disable;
-				};
-			};
-
-			spdifrx_sleep_pins_a: spdifrx-1 {
-				pins {
-					pinmux = <STM32_PINMUX('G', 12, ANALOG)>; /* SPDIF_IN1 */
-				};
-			};
-
-			uart4_pins_a: uart4-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
-					bias-disable;
-				};
-			};
-
-			uart4_pins_b: uart4-1 {
-				pins1 {
-					pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
-					bias-disable;
-				};
-			};
-
-			uart7_pins_a: uart7-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART4_TX */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <0>;
-				};
-				pins2 {
-					pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART4_RX */
-						 <STM32_PINMUX('E', 10, AF7)>, /* UART4_CTS */
-						 <STM32_PINMUX('E', 9, AF7)>; /* UART4_RTS */
-					bias-disable;
-				};
-			};
-		};
-
-		pinctrl_z: pin-controller-z@54004000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "st,stm32mp157-z-pinctrl";
-			ranges = <0 0x54004000 0x400>;
-			pins-are-numbered;
-			interrupt-parent = <&exti>;
-			st,syscfg = <&exti 0x60 0xff>;
-
-			gpioz: gpio@54004000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0 0x400>;
-				clocks = <&rcc GPIOZ>;
-				st,bank-name = "GPIOZ";
-				st,bank-ioport = <11>;
-				status = "disabled";
-			};
-
-			i2c2_pins_b2: i2c2-0 {
-				pins {
-					pinmux = <STM32_PINMUX('Z', 0, AF3)>; /* I2C2_SCL */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c2_pins_sleep_b2: i2c2-1 {
-				pins {
-					pinmux = <STM32_PINMUX('Z', 0, ANALOG)>; /* I2C2_SCL */
-				};
-			};
-
-			i2c4_pins_a: i2c4-0 {
-				pins {
-					pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
-						 <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
-					bias-disable;
-					drive-open-drain;
-					slew-rate = <0>;
-				};
-			};
-
-			i2c4_pins_sleep_a: i2c4-1 {
-				pins {
-					pinmux = <STM32_PINMUX('Z', 4, ANALOG)>, /* I2C4_SCL */
-						 <STM32_PINMUX('Z', 5, ANALOG)>; /* I2C4_SDA */
-				};
-			};
-
-			spi1_pins_a: spi1-0 {
-				pins1 {
-					pinmux = <STM32_PINMUX('Z', 0, AF5)>, /* SPI1_SCK */
-						 <STM32_PINMUX('Z', 2, AF5)>; /* SPI1_MOSI */
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <1>;
-				};
-
-				pins2 {
-					pinmux = <STM32_PINMUX('Z', 1, AF5)>; /* SPI1_MISO */
-					bias-disable;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stm32mp157xaa-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157xaa-pinctrl.dtsi
deleted file mode 100644
index 875adf5e1e30..000000000000
--- a/arch/arm/boot/dts/stm32mp157xaa-pinctrl.dtsi
+++ /dev/null
@@ -1,90 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
- * Author: Alexandre Torgue <alexandre.torgue@st.com>
- */
-
-#include "stm32mp157-pinctrl.dtsi"
-/ {
-	soc {
-		pinctrl: pin-controller@50002000 {
-			st,package = <STM32MP_PKG_AA>;
-
-			gpioa: gpio@50002000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 0 16>;
-			};
-
-			gpiob: gpio@50003000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 16 16>;
-			};
-
-			gpioc: gpio@50004000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 32 16>;
-			};
-
-			gpiod: gpio@50005000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 48 16>;
-			};
-
-			gpioe: gpio@50006000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 64 16>;
-			};
-
-			gpiof: gpio@50007000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 80 16>;
-			};
-
-			gpiog: gpio@50008000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 96 16>;
-			};
-
-			gpioh: gpio@50009000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 112 16>;
-			};
-
-			gpioi: gpio@5000a000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 128 16>;
-			};
-
-			gpioj: gpio@5000b000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 144 16>;
-			};
-
-			gpiok: gpio@5000c000 {
-				status = "okay";
-				ngpios = <8>;
-				gpio-ranges = <&pinctrl 0 160 8>;
-			};
-		};
-
-		pinctrl_z: pin-controller-z@54004000 {
-			st,package = <STM32MP_PKG_AA>;
-
-			gpioz: gpio@54004000 {
-				status = "okay";
-				ngpios = <8>;
-				gpio-ranges = <&pinctrl_z 0 400 8>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stm32mp157xab-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157xab-pinctrl.dtsi
deleted file mode 100644
index 961fa12a59c3..000000000000
--- a/arch/arm/boot/dts/stm32mp157xab-pinctrl.dtsi
+++ /dev/null
@@ -1,62 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
- * Author: Alexandre Torgue <alexandre.torgue@st.com>
- */
-
-#include "stm32mp157-pinctrl.dtsi"
-/ {
-	soc {
-		pinctrl: pin-controller@50002000 {
-			st,package = <STM32MP_PKG_AB>;
-
-			gpioa: gpio@50002000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 0 16>;
-			};
-
-			gpiob: gpio@50003000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 16 16>;
-			};
-
-			gpioc: gpio@50004000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 32 16>;
-			};
-
-			gpiod: gpio@50005000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 48 16>;
-			};
-
-			gpioe: gpio@50006000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 64 16>;
-			};
-
-			gpiof: gpio@50007000 {
-				status = "okay";
-				ngpios = <6>;
-				gpio-ranges = <&pinctrl 6 86 6>;
-			};
-
-			gpiog: gpio@50008000 {
-				status = "okay";
-				ngpios = <10>;
-				gpio-ranges = <&pinctrl 6 102 10>;
-			};
-
-			gpioh: gpio@50009000 {
-				status = "okay";
-				ngpios = <2>;
-				gpio-ranges = <&pinctrl 0 112 2>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stm32mp157xac-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157xac-pinctrl.dtsi
deleted file mode 100644
index 26600f188d25..000000000000
--- a/arch/arm/boot/dts/stm32mp157xac-pinctrl.dtsi
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
- * Author: Alexandre Torgue <alexandre.torgue@st.com>
- */
-
-#include "stm32mp157-pinctrl.dtsi"
-/ {
-	soc {
-		pinctrl: pin-controller@50002000 {
-			st,package = <STM32MP_PKG_AC>;
-
-			gpioa: gpio@50002000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 0 16>;
-			};
-
-			gpiob: gpio@50003000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 16 16>;
-			};
-
-			gpioc: gpio@50004000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 32 16>;
-			};
-
-			gpiod: gpio@50005000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 48 16>;
-			};
-
-			gpioe: gpio@50006000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 64 16>;
-			};
-
-			gpiof: gpio@50007000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 80 16>;
-			};
-
-			gpiog: gpio@50008000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 96 16>;
-			};
-
-			gpioh: gpio@50009000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 112 16>;
-			};
-
-			gpioi: gpio@5000a000 {
-				status = "okay";
-				ngpios = <12>;
-				gpio-ranges = <&pinctrl 0 128 12>;
-			};
-		};
-
-		pinctrl_z: pin-controller-z@54004000 {
-			st,package = <STM32MP_PKG_AC>;
-
-			gpioz: gpio@54004000 {
-				status = "okay";
-				ngpios = <8>;
-				gpio-ranges = <&pinctrl_z 0 400 8>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/stm32mp157xad-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157xad-pinctrl.dtsi
deleted file mode 100644
index 910113f3e69a..000000000000
--- a/arch/arm/boot/dts/stm32mp157xad-pinctrl.dtsi
+++ /dev/null
@@ -1,62 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
- * Author: Alexandre Torgue <alexandre.torgue@st.com>
- */
-
-#include "stm32mp157-pinctrl.dtsi"
-/ {
-	soc {
-		pinctrl: pin-controller@50002000 {
-			st,package = <STM32MP_PKG_AD>;
-
-			gpioa: gpio@50002000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 0 16>;
-			};
-
-			gpiob: gpio@50003000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 16 16>;
-			};
-
-			gpioc: gpio@50004000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 32 16>;
-			};
-
-			gpiod: gpio@50005000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 48 16>;
-			};
-
-			gpioe: gpio@50006000 {
-				status = "okay";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 64 16>;
-			};
-
-			gpiof: gpio@50007000 {
-				status = "okay";
-				ngpios = <6>;
-				gpio-ranges = <&pinctrl 6 86 6>;
-			};
-
-			gpiog: gpio@50008000 {
-				status = "okay";
-				ngpios = <10>;
-				gpio-ranges = <&pinctrl 6 102 10>;
-			};
-
-			gpioh: gpio@50009000 {
-				status = "okay";
-				ngpios = <2>;
-				gpio-ranges = <&pinctrl 0 112 2>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
deleted file mode 100644
index d277d043031b..000000000000
--- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ /dev/null
@@ -1,153 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
- *
- * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
- *   Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
- */
-
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	model = "Banana Pi BPI-M2-Zero";
-	compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
-
-	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		pwr_led {
-			label = "bananapi-m2-zero:red:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-			default-state = "on";
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-
-		sw4 {
-			label = "power";
-			linux,code = <BTN_0>;
-			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	reg_vdd_cpux: vdd-cpux-regulator {
-		compatible = "regulator-gpio";
-		regulator-name = "vdd-cpux";
-		regulator-type = "voltage";
-		regulator-boot-on;
-		regulator-always-on;
-		regulator-min-microvolt = <1100000>;
-		regulator-max-microvolt = <1300000>;
-		regulator-ramp-delay = <50>; /* 4ms */
-
-		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
-		enable-active-high;
-		gpios-states = <0x1>;
-		states = <1100000 0>, <1300000 1>;
-	};
-
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
-		clock-names = "ext_clock";
-	};
-};
-
-&cpu0 {
-	cpu-supply = <&reg_vdd_cpux>;
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&mmc0 {
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	/*
-	 * On the production batch of this board the card detect GPIO is
-	 * high active (card inserted), although on the early samples it's
-	 * low active.
-	 */
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	status = "okay";
-};
-
-&mmc1 {
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-		interrupt-parent = <&pio>;
-		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
-		interrupt-names = "host-wake";
-	};
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pa_pins>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
-	uart-has-rtscts;
-	status = "okay";
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
-		clock-names = "lpo";
-		vbat-supply = <&reg_vcc3v3>;
-		vddio-supply = <&reg_vcc3v3>;
-		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
-		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
-		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
-	};
-
-};
-
-&usb_otg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usbphy {
-	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
-	/*
-	 * There're two micro-USB connectors, one is power-only and another is
-	 * OTG. The Vbus of these two connectors are connected together, so
-	 * the external USB device will be powered just by the power input
-	 * from the power-only USB port.
-	 */
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/sun8i-v3.dtsi b/arch/arm/boot/dts/sun8i-v3.dtsi
deleted file mode 100644
index 6ae8645ade50..000000000000
--- a/arch/arm/boot/dts/sun8i-v3.dtsi
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.io>
- */
-
-#include "sun8i-v3s.dtsi"
-
-&ccu {
-	compatible = "allwinner,sun8i-v3-ccu";
-};
-
-&pio {
-	compatible = "allwinner,sun8i-v3-pinctrl";
-};
diff --git a/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts b/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts
deleted file mode 100644
index a1154e6c7cb5..000000000000
--- a/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR X11)
-/*
- * Copyright 2018 Icenowy Zheng <icenowy@aosc.io>
- */
-
-/dts-v1/;
-#include "suniv-f1c100s.dtsi"
-
-/ {
-	model = "Lichee Pi Nano";
-	compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s";
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pe_pins>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/suniv-f1c100s.dtsi b/arch/arm/boot/dts/suniv-f1c100s.dtsi
deleted file mode 100644
index 6100d3b75f61..000000000000
--- a/arch/arm/boot/dts/suniv-f1c100s.dtsi
+++ /dev/null
@@ -1,144 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR X11)
-/*
- * Copyright 2018 Icenowy Zheng <icenowy@aosc.io>
- * Copyright 2018 Mesih Kilinc <mesihkilinc@gmail.com>
- */
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&intc>;
-
-	clocks {
-		osc24M: clk-24M {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <24000000>;
-			clock-output-names = "osc24M";
-		};
-
-		osc32k: clk-32k {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-			clock-output-names = "osc32k";
-		};
-	};
-
-	cpus {
-		cpu {
-			compatible = "arm,arm926ej-s";
-			device_type = "cpu";
-		};
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		sram-controller@1c00000 {
-			compatible = "allwinner,suniv-f1c100s-system-control",
-				     "allwinner,sun4i-a10-system-control";
-			reg = <0x01c00000 0x30>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			sram_d: sram@10000 {
-				compatible = "mmio-sram";
-				reg = <0x00010000 0x1000>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				ranges = <0 0x00010000 0x1000>;
-
-				otg_sram: sram-section@0 {
-					compatible = "allwinner,suniv-f1c100s-sram-d",
-						     "allwinner,sun4i-a10-sram-d";
-					reg = <0x0000 0x1000>;
-					status = "disabled";
-				};
-			};
-		};
-
-		ccu: clock@1c20000 {
-			compatible = "allwinner,suniv-f1c100s-ccu";
-			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&osc32k>;
-			clock-names = "hosc", "losc";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		intc: interrupt-controller@1c20400 {
-			compatible = "allwinner,suniv-f1c100s-ic";
-			reg = <0x01c20400 0x400>;
-			interrupt-controller;
-			#interrupt-cells = <1>;
-		};
-
-		pio: pinctrl@1c20800 {
-			compatible = "allwinner,suniv-f1c100s-pinctrl";
-			reg = <0x01c20800 0x400>;
-			interrupts = <38>, <39>, <40>;
-			clocks = <&ccu 37>, <&osc24M>, <&osc32k>;
-			clock-names = "apb", "hosc", "losc";
-			gpio-controller;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			#gpio-cells = <3>;
-
-			uart0_pe_pins: uart0-pe-pins {
-				pins = "PE0", "PE1";
-				function = "uart0";
-			};
-		};
-
-		timer@1c20c00 {
-			compatible = "allwinner,suniv-f1c100s-timer";
-			reg = <0x01c20c00 0x90>;
-			interrupts = <13>;
-			clocks = <&osc24M>;
-		};
-
-		wdt: watchdog@1c20ca0 {
-			compatible = "allwinner,suniv-f1c100s-wdt",
-				     "allwinner,sun4i-a10-wdt";
-			reg = <0x01c20ca0 0x20>;
-		};
-
-		uart0: serial@1c25000 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c25000 0x400>;
-			interrupts = <1>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&ccu 38>;
-			resets = <&ccu 24>;
-			status = "disabled";
-		};
-
-		uart1: serial@1c25400 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c25400 0x400>;
-			interrupts = <2>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&ccu 39>;
-			resets = <&ccu 25>;
-			status = "disabled";
-		};
-
-		uart2: serial@1c25800 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c25800 0x400>;
-			interrupts = <3>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&ccu 40>;
-			resets = <&ccu 26>;
-			status = "disabled";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/sunplus/Makefile b/arch/arm/boot/dts/sunplus/Makefile
new file mode 100644
index 000000000000..868f2ea0c127
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_SP7021) += \
+	sunplus-sp7021-demo-v3.dtb
+dtb-$(CONFIG_SOC_SP7021) += \
+	sunplus-sp7021-demo-v3.dtb
diff --git a/arch/arm/boot/dts/sunplus/sunplus-sp7021-achip.dtsi b/arch/arm/boot/dts/sunplus/sunplus-sp7021-achip.dtsi
new file mode 100644
index 000000000000..493d32357e4e
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus/sunplus-sp7021-achip.dtsi
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Sunplus SP7021
+ *
+ * Copyright (C) 2021 Sunplus Technology Co.
+ */
+
+#include "sunplus-sp7021.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "sunplus,sp7021-achip", "sunplus,sp7021";
+	model = "Sunplus SP7021 (CA7)";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <931000000>;
+		};
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+			clock-frequency = <931000000>;
+		};
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+			clock-frequency = <931000000>;
+		};
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+			clock-frequency = <931000000>;
+		};
+	};
+
+	gic: interrupt-controller@9f101000 {
+		compatible = "arm,cortex-a7-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x9f101000 0x1000>,
+		      <0x9f102000 0x2000>,
+		      <0x9f104000 0x2000>,
+		      <0x9f106000 0x2000>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <XTAL>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	soc@9c000000 {
+		intc: interrupt-controller@780 {
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, /* EXT_INT0 */
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; /* EXT_INT1 */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sunplus/sunplus-sp7021-demo-v3.dts b/arch/arm/boot/dts/sunplus/sunplus-sp7021-demo-v3.dts
new file mode 100644
index 000000000000..d5c5ffc20565
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus/sunplus-sp7021-demo-v3.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Sunplus SP7021 Demo V3 SBC board
+ *
+ * Copyright (C) Sunplus Technology Co.
+ */
+
+/dts-v1/;
+
+#include "sunplus-sp7021-achip.dtsi"
+
+/ {
+	compatible = "sunplus,sp7021-demo-v3", "sunplus,sp7021";
+	model = "Sunplus SP7021/CA7/Demo_V3";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/sunplus/sunplus-sp7021.dtsi b/arch/arm/boot/dts/sunplus/sunplus-sp7021.dtsi
new file mode 100644
index 000000000000..ae9bbe0320b8
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus/sunplus-sp7021.dtsi
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Sunplus SP7021
+ *
+ * Copyright (C) 2021 Sunplus Technology Co.
+ */
+
+#include <dt-bindings/clock/sunplus,sp7021-clkc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/reset/sunplus,sp7021-reset.h>
+#include <dt-bindings/pinctrl/sppctl-sp7021.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#define XTAL	27000000
+
+/ {
+	compatible = "sunplus,sp7021";
+	model = "Sunplus SP7021";
+
+	clocks {
+		extclk: osc0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <XTAL>;
+			clock-output-names = "extclk";
+		};
+	};
+
+	soc@9c000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x9c000000 0x400000>;
+		interrupt-parent = <&intc>;
+
+		clkc: clock-controller@4 {
+			compatible = "sunplus,sp7021-clkc";
+			reg = <0x4 0x28>,
+			      <0x200 0x44>,
+			      <0x268 0x04>;
+			clocks = <&extclk>;
+			#clock-cells = <1>;
+		};
+
+		intc: interrupt-controller@780 {
+			compatible = "sunplus,sp7021-intc";
+			reg = <0x780 0x80>, <0xa80 0x80>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		otp: otp@af00 {
+			compatible = "sunplus,sp7021-ocotp";
+			reg = <0xaf00 0x34>, <0xaf80 0x58>;
+			reg-names = "hb_gpio", "otprx";
+			clocks = <&clkc CLK_OTPRX>;
+			resets = <&rstc RST_OTPRX>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			therm_calib: thermal-calibration@14 {
+				reg = <0x14 0x3>;
+			};
+			disc_vol: disconnect-voltage@18 {
+				reg = <0x18 0x2>;
+			};
+			mac_addr0: mac-address0@34 {
+				reg = <0x34 0x6>;
+			};
+			mac_addr1: mac-address1@3a {
+				reg = <0x3a 0x6>;
+			};
+		};
+
+		pctl: pinctrl@100 {
+			compatible = "sunplus,sp7021-pctl";
+			reg = <0x100 0x100>,
+			      <0x300 0x100>,
+			      <0x32e4 0x1C>,
+			      <0x80 0x20>;
+			reg-names = "moon2", "gpioxt", "first", "moon1";
+			gpio-controller;
+			#gpio-cells = <2>;
+			clocks = <&clkc CLK_GPIO>;
+			resets = <&rstc RST_GPIO>;
+
+			emac_pins: pinmux-emac-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(49,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_CLK_OUT,0)
+					SPPCTL_IOPAD(44,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDC,0)
+					SPPCTL_IOPAD(43,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDIO,0)
+					SPPCTL_IOPAD(52,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXEN,0)
+					SPPCTL_IOPAD(50,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD0,0)
+					SPPCTL_IOPAD(51,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD1,0)
+					SPPCTL_IOPAD(46,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_CRSDV,0)
+					SPPCTL_IOPAD(47,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD0,0)
+					SPPCTL_IOPAD(48,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD1,0)
+					SPPCTL_IOPAD(45,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXER,0)
+					SPPCTL_IOPAD(59,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXEN,0)
+					SPPCTL_IOPAD(57,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXD0,0)
+					SPPCTL_IOPAD(58,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXD1,0)
+					SPPCTL_IOPAD(54,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_CRSDV,0)
+					SPPCTL_IOPAD(55,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXD0,0)
+					SPPCTL_IOPAD(56,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXD1,0)
+					SPPCTL_IOPAD(53,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXER,0)
+				>;
+				sunplus,zerofunc = <
+					MUXF_L2SW_LED_FLASH0
+					MUXF_L2SW_LED_FLASH1
+					MUXF_L2SW_LED_ON0
+					MUXF_L2SW_LED_ON1
+					MUXF_DAISY_MODE
+				>;
+			};
+
+			emmc_pins: pinmux-emmc-pins {
+				function = "CARD0_EMMC";
+				groups = "CARD0_EMMC";
+			};
+
+			leds_pins: pinmux-leds-pins {
+				sunplus,pins = < SPPCTL_IOPAD(0,SPPCTL_PCTL_G_GPIO,0,SPPCTL_PCTL_L_OUT) >;
+			};
+
+			sdcard_pins: pinmux-sdcard-pins {
+				function = "SD_CARD";
+				groups = "SD_CARD";
+				sunplus,pins = < SPPCTL_IOPAD(91, SPPCTL_PCTL_G_GPIO, 0, 0) >;
+			};
+
+			spi0_pins: pinmux-spi0-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(26,SPPCTL_PCTL_G_GPIO,0,0)
+					SPPCTL_IOPAD(28,SPPCTL_PCTL_G_GPIO,0,0)
+					SPPCTL_IOPAD(23,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_DO,0)
+					SPPCTL_IOPAD(25,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_DI,0)
+					SPPCTL_IOPAD(27,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_CLK,0)
+				>;
+			};
+
+			uart0_pins: pinmux-uart0-pins {
+				function = "UA0";
+				groups = "UA0";
+			};
+
+			uart1_pins: pinmux-uart1-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(14,SPPCTL_PCTL_G_PMUX,MUXF_UA4_TX,0)
+					SPPCTL_IOPAD(16,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RX,0)
+				>;
+			};
+
+			uart2_pins: pinmux-uart2-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(16,SPPCTL_PCTL_G_PMUX,MUXF_UA2_TX,0)
+					SPPCTL_IOPAD(17,SPPCTL_PCTL_G_PMUX,MUXF_UA2_RX,0)
+					SPPCTL_IOPAD(18,SPPCTL_PCTL_G_PMUX,MUXF_UA2_RTS,0)
+					SPPCTL_IOPAD(19,SPPCTL_PCTL_G_PMUX,MUXF_UA2_CTS,0)
+				>;
+			};
+
+			uart4_pins: pinmux-uart4-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(22,SPPCTL_PCTL_G_PMUX,MUXF_UA4_TX,0)
+					SPPCTL_IOPAD(20,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RX,0)
+					SPPCTL_IOPAD(23,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RTS,0)
+					SPPCTL_IOPAD(21,SPPCTL_PCTL_G_PMUX,MUXF_UA4_CTS,0)
+				>;
+			};
+		};
+
+		rstc: reset@54 {
+			compatible = "sunplus,sp7021-reset";
+			reg = <0x54 0x28>;
+			#reset-cells = <1>;
+		};
+
+		rtc: rtc@3a00 {
+			compatible = "sunplus,sp7021-rtc";
+			reg = <0x3a00 0x80>;
+			reg-names = "rtc";
+			clocks = <&clkc CLK_RTC>;
+			resets = <&rstc RST_RTC>;
+			interrupts = <163 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		spi_controller0: spi@2d80 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0x2d80 0x80>, <0x2e00 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <144 IRQ_TYPE_LEVEL_HIGH>,
+				     <146 IRQ_TYPE_LEVEL_HIGH>,
+				     <145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_0>;
+			resets = <&rstc RST_SPI_COMBO_0>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			cs-gpios = <&pctl 26 GPIO_ACTIVE_LOW>,
+				   <&pctl 28 GPIO_ACTIVE_LOW>;
+		};
+
+		spi_controller1: spi@f480 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0xf480 0x80>, <0xf500 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <67 IRQ_TYPE_LEVEL_HIGH>,
+				     <69 IRQ_TYPE_LEVEL_HIGH>,
+				     <68 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_1>;
+			resets = <&rstc RST_SPI_COMBO_1>;
+			status = "disabled";
+		};
+
+		spi_controller2: spi@f600 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0xf600 0x80>, <0xf680 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <70 IRQ_TYPE_LEVEL_HIGH>,
+				     <72 IRQ_TYPE_LEVEL_HIGH>,
+				     <71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_2>;
+			resets = <&rstc RST_SPI_COMBO_2>;
+			status = "disabled";
+		};
+
+		spi_controller3: spi@f780 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0xf780 0x80>, <0xf800 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <73 IRQ_TYPE_LEVEL_HIGH>,
+				     <75 IRQ_TYPE_LEVEL_HIGH>,
+				     <74 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_3>;
+			resets = <&rstc RST_SPI_COMBO_3>;
+			status = "disabled";
+		};
+
+		uart0: serial@900 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x900 0x80>;
+			interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA0>;
+			resets = <&rstc RST_UA0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+		};
+
+		uart1: serial@980 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x980 0x80>;
+			interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA1>;
+			resets = <&rstc RST_UA1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_pins>;
+			status = "disabled";
+		};
+
+		uart2: serial@800 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x800 0x80>;
+			interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA2>;
+			resets = <&rstc RST_UA2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart2_pins>;
+			status = "disabled";
+		};
+
+		uart3: serial@880 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x880 0x80>;
+			interrupts = <56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA3>;
+			resets = <&rstc RST_UA3>;
+			status = "disabled";
+		};
+
+		uart4: serial@8780 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x8780 0x80>;
+			interrupts = <134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA4>;
+			resets = <&rstc RST_UA4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart4_pins>;
+			status = "disabled";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+		system-led {
+			label = "system-led";
+			gpios = <&pctl 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/synaptics/Makefile b/arch/arm/boot/dts/synaptics/Makefile
new file mode 100644
index 000000000000..0ecccd156d18
--- /dev/null
+++ b/arch/arm/boot/dts/synaptics/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_BERLIN) += \
+	berlin2-sony-nsz-gs7.dtb \
+	berlin2cd-google-chromecast.dtb \
+	berlin2cd-valve-steamlink.dtb \
+	berlin2q-marvell-dmp.dtb
diff --git a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts b/arch/arm/boot/dts/synaptics/berlin2-sony-nsz-gs7.dts
index 64a297759eb9..64a297759eb9 100644
--- a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts
+++ b/arch/arm/boot/dts/synaptics/berlin2-sony-nsz-gs7.dts
diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/synaptics/berlin2.dtsi
index d2f7d984bba5..1114c592e461 100644
--- a/arch/arm/boot/dts/berlin2.dtsi
+++ b/arch/arm/boot/dts/synaptics/berlin2.dtsi
@@ -77,7 +77,7 @@
 
 		ranges = <0 0xf7000000 0x1000000>;
 
-		sdhci0: sdhci@ab0000 {
+		sdhci0: mmc@ab0000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0000 0x200>;
 			clocks = <&chip_clk CLKID_SDIO0XIN>, <&chip_clk CLKID_SDIO0>;
@@ -86,7 +86,7 @@
 			status = "disabled";
 		};
 
-		sdhci1: sdhci@ab0800 {
+		sdhci1: mmc@ab0800 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0800 0x200>;
 			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO1>;
@@ -95,7 +95,7 @@
 			status = "disabled";
 		};
 
-		sdhci2: sdhci@ab1000 {
+		sdhci2: mmc@ab1000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab1000 0x200>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
@@ -106,7 +106,7 @@
 			status = "disabled";
 		};
 
-		l2: l2-cache-controller@ac0000 {
+		l2: cache-controller@ac0000 {
 			compatible = "marvell,tauros3-cache", "arm,pl310-cache";
 			reg = <0xac0000 0x1000>;
 			cache-unified;
@@ -191,7 +191,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -209,7 +209,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -227,7 +227,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -245,7 +245,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -446,7 +446,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 				};
 			};
@@ -461,7 +461,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts b/arch/arm/boot/dts/synaptics/berlin2cd-google-chromecast.dts
index 56fa951bc86f..c1d91424e658 100644
--- a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts
+++ b/arch/arm/boot/dts/synaptics/berlin2cd-google-chromecast.dts
@@ -34,19 +34,19 @@
 		linux,usable-memory = <0x00000000 0x20000000>; /* 512 MB */
 	};
 
-	leds {
+	led-controller {
 		compatible = "pwm-leds";
 		pinctrl-0 = <&ledpwm_pmux>;
 		pinctrl-names = "default";
 
-		white {
+		led-1 {
 			label = "white";
 			pwms = <&pwm 0 600000 0>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};
 
-		red {
+		led-2 {
 			label = "red";
 			pwms = <&pwm 1 600000 0>;
 			max-brightness = <255>;
diff --git a/arch/arm/boot/dts/berlin2cd-valve-steamlink.dts b/arch/arm/boot/dts/synaptics/berlin2cd-valve-steamlink.dts
index 79ac842ae461..79ac842ae461 100644
--- a/arch/arm/boot/dts/berlin2cd-valve-steamlink.dts
+++ b/arch/arm/boot/dts/synaptics/berlin2cd-valve-steamlink.dts
diff --git a/arch/arm/boot/dts/berlin2cd.dtsi b/arch/arm/boot/dts/synaptics/berlin2cd.dtsi
index e5c1f4213ff9..b2768f7a3185 100644
--- a/arch/arm/boot/dts/berlin2cd.dtsi
+++ b/arch/arm/boot/dts/synaptics/berlin2cd.dtsi
@@ -62,7 +62,7 @@
 
 		ranges = <0 0xf7000000 0x1000000>;
 
-		sdhci0: sdhci@ab0000 {
+		sdhci0: mmc@ab0000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0000 0x200>;
 			clocks = <&chip_clk CLKID_SDIO0XIN>, <&chip_clk CLKID_SDIO0>;
@@ -71,7 +71,7 @@
 			status = "disabled";
 		};
 
-		l2: l2-cache-controller@ac0000 {
+		l2: cache-controller@ac0000 {
 			compatible = "arm,pl310-cache";
 			reg = <0xac0000 0x1000>;
 			cache-unified;
@@ -181,7 +181,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -199,7 +199,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -217,7 +217,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -235,7 +235,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -473,7 +473,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 				};
 			};
@@ -518,7 +518,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 				};
 			};
diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/synaptics/berlin2q-marvell-dmp.dts
index c162f98cb8e8..c162f98cb8e8 100644
--- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
+++ b/arch/arm/boot/dts/synaptics/berlin2q-marvell-dmp.dts
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/synaptics/berlin2q.dtsi
index 99d6872a6dfc..6edaefa617a5 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/synaptics/berlin2q.dtsi
@@ -122,7 +122,7 @@
 		ranges = <0 0xf7000000 0x1000000>;
 		interrupt-parent = <&gic>;
 
-		sdhci0: sdhci@ab0000 {
+		sdhci0: mmc@ab0000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0000 0x200>;
 			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
@@ -131,7 +131,7 @@
 			status = "disabled";
 		};
 
-		sdhci1: sdhci@ab0800 {
+		sdhci1: mmc@ab0800 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab0800 0x200>;
 			clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
@@ -140,7 +140,7 @@
 			status = "disabled";
 		};
 
-		sdhci2: sdhci@ab1000 {
+		sdhci2: mmc@ab1000 {
 			compatible = "mrvl,pxav3-mmc";
 			reg = <0xab1000 0x200>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
@@ -149,7 +149,7 @@
 			status = "disabled";
 		};
 
-		l2: l2-cache-controller@ac0000 {
+		l2: cache-controller@ac0000 {
 			compatible = "arm,pl310-cache";
 			reg = <0xac0000 0x1000>;
 			cache-unified;
@@ -252,7 +252,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -270,7 +270,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -288,7 +288,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -306,7 +306,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@@ -552,7 +552,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 				};
 			};
@@ -581,7 +581,7 @@
 				status = "disabled";
 			};
 
-			uart0: uart@9000 {
+			uart0: serial@9000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x9000 0x100>;
 				interrupts = <8>;
@@ -592,7 +592,7 @@
 				status = "disabled";
 			};
 
-			uart1: uart@a000 {
+			uart1: serial@a000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0xa000 0x100>;
 				interrupts = <9>;
@@ -613,7 +613,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 				};
 			};
diff --git a/arch/arm/boot/dts/tango4-common.dtsi b/arch/arm/boot/dts/tango4-common.dtsi
deleted file mode 100644
index ff72a8efb73d..000000000000
--- a/arch/arm/boot/dts/tango4-common.dtsi
+++ /dev/null
@@ -1,184 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Based on Mans Rullgard's Tango3 DT
- * https://github.com/mansr/linux-tangox
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-
-#define  CPU_CLK	0
-#define  SYS_CLK	1
-#define  USB_CLK	2
-#define SDIO_CLK	3
-
-/ {
-	interrupt-parent = <&gic>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	periph_clk: periph_clk {
-		compatible = "fixed-factor-clock";
-		clocks = <&clkgen CPU_CLK>;
-		clock-mult = <1>;
-		clock-div  = <2>;
-		#clock-cells = <0>;
-	};
-
-	mpcore {
-		compatible = "simple-bus";
-		ranges = <0x00000000 0x20000000 0x2000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		scu@0 {
-			compatible = "arm,cortex-a9-scu";
-			reg = <0x0 0x100>;
-		};
-
-		twd@600 {
-			compatible = "arm,cortex-a9-twd-timer";
-			reg = <0x600 0x10>;
-			interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>;
-			clocks = <&periph_clk>;
-			always-on;
-		};
-
-		gic: interrupt-controller@1000 {
-			compatible = "arm,cortex-a9-gic";
-			#interrupt-cells = <3>;
-			interrupt-controller;
-			reg = <0x1000 0x1000>, <0x100 0x100>;
-		};
-	};
-
-	l2cc: l2-cache-controller@20100000 {
-		compatible = "arm,pl310-cache";
-		reg = <0x20100000 0x1000>;
-		cache-level = <2>;
-		cache-unified;
-	};
-
-	soc {
-		compatible = "simple-bus";
-		interrupt-parent = <&irq0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		xtal: xtal {
-			compatible = "fixed-clock";
-			clock-frequency = <27000000>;
-			#clock-cells = <0>;
-		};
-
-		clkgen: clkgen@10000 {
-			compatible = "sigma,tango4-clkgen";
-			reg = <0x10000 0x100>;
-			clocks = <&xtal>;
-			#clock-cells = <1>;
-		};
-
-		tick-counter@10048 {
-			compatible = "sigma,tick-counter";
-			reg = <0x10048 0x4>;
-			clocks = <&xtal>;
-		};
-
-		uart: serial@10700 {
-			compatible = "ralink,rt2880-uart";
-			reg = <0x10700 0x30>;
-			interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
-			clock-frequency = <7372800>;
-			reg-shift = <2>;
-		};
-
-		watchdog@1fd00 {
-			compatible = "sigma,smp8759-wdt";
-			reg = <0x1fd00 8>;
-			clocks = <&xtal>;
-		};
-
-		mmc0: mmc@21000 {
-			compatible = "arasan,sdhci-8.9a";
-			reg = <0x21000 0x200>;
-			clock-names = "clk_xin", "clk_ahb";
-			clocks = <&clkgen SDIO_CLK>, <&clkgen SYS_CLK>;
-			interrupts = <60 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		mmc1: mmc@21200 {
-			compatible = "arasan,sdhci-8.9a";
-			reg = <0x21200 0x200>;
-			clock-names = "clk_xin", "clk_ahb";
-			clocks = <&clkgen SDIO_CLK>, <&clkgen SYS_CLK>;
-			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		usb0: usb@21400 {
-			compatible = "chipidea,usb2";
-			reg = <0x21400 0x200>;
-			interrupts = <40 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb0_phy>;
-			phy-names = "usb-phy";
-		};
-
-		usb0_phy: phy@21700 {
-			compatible = "sigma,smp8642-usb-phy";
-			reg = <0x21700 0x100>;
-			#phy-cells = <0>;
-			clocks = <&clkgen USB_CLK>;
-		};
-
-		usb1: usb@25400 {
-			compatible = "chipidea,usb2";
-			reg = <0x25400 0x200>;
-			interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb1_phy>;
-			phy-names = "usb-phy";
-		};
-
-		usb1_phy: phy@25700 {
-			compatible = "sigma,smp8642-usb-phy";
-			reg = <0x25700 0x100>;
-			#phy-cells = <0>;
-			clocks = <&clkgen USB_CLK>;
-		};
-
-		eth0: ethernet@26000 {
-			compatible = "sigma,smp8734-ethernet";
-			reg = <0x26000 0x800>;
-			interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clkgen SYS_CLK>;
-		};
-
-		intc: interrupt-controller@6e000 {
-			compatible = "sigma,smp8642-intc";
-			reg = <0x6e000 0x400>;
-			ranges = <0 0x6e000 0x400>;
-			interrupt-parent = <&gic>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			irq0: irq0@0 {
-				reg = <0x000 0x100>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-			};
-
-			irq1: irq1@100 {
-				reg = <0x100 0x100>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-			};
-
-			irq2: irq2@300 {
-				reg = <0x300 0x100>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/tango4-smp8758.dtsi b/arch/arm/boot/dts/tango4-smp8758.dtsi
deleted file mode 100644
index 1c6a5bf1a86b..000000000000
--- a/arch/arm/boot/dts/tango4-smp8758.dtsi
+++ /dev/null
@@ -1,57 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "tango4-common.dtsi"
-
-/ {
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		enable-method = "sigma,tango4-smp";
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a9";
-			next-level-cache = <&l2cc>;
-			device_type = "cpu";
-			reg = <0>;
-			clocks = <&clkgen CPU_CLK>;
-			clock-latency = <1>;
-		};
-
-		cpu1: cpu@1 {
-			compatible = "arm,cortex-a9";
-			next-level-cache = <&l2cc>;
-			device_type = "cpu";
-			reg = <1>;
-		};
-	};
-
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupt-affinity = <&cpu0>, <&cpu1>;
-		interrupts =
-			<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
-			<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
-	soc {
-		cpu_temp: thermal@920100 {
-			#thermal-sensor-cells = <0>;
-			compatible = "sigma,smp8758-thermal";
-			reg = <0x920100 12>;
-		};
-	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			polling-delay = <997>;		/* milliseconds */
-			polling-delay-passive = <499>;	/* milliseconds */
-			thermal-sensors = <&cpu_temp>;
-			trips {
-				cpu_critical {
-					temperature = <120000>;
-					hysteresis = <2500>;
-					type = "critical";
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/tango4-vantage-1172.dts b/arch/arm/boot/dts/tango4-vantage-1172.dts
deleted file mode 100644
index d237d7f02c51..000000000000
--- a/arch/arm/boot/dts/tango4-vantage-1172.dts
+++ /dev/null
@@ -1,42 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include "tango4-smp8758.dtsi"
-
-/ {
-	model = "Sigma Designs SMP8758 Vantage-1172 Rev E1";
-	compatible = "sigma,vantage-1172", "sigma,smp8758", "sigma,tango4";
-
-	aliases {
-		serial = &uart;
-		eth0 = &eth0;
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x80000000>; /* 2 GB */
-	};
-
-	chosen {
-		stdout-path = "serial:115200n8";
-	};
-};
-
-&eth0 {
-	phy-connection-type = "rgmii-id";
-	phy-handle = <&eth0_phy>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	/* Atheros AR8035 */
-	eth0_phy: ethernet-phy@4 {
-		compatible = "ethernet-phy-id004d.d072",
-			     "ethernet-phy-ieee802.3-c22";
-		interrupts = <37 IRQ_TYPE_EDGE_RISING>;
-		reg = <4>;
-	};
-};
-
-&mmc1 {
-	non-removable; /* eMMC */
-};
diff --git a/arch/arm/boot/dts/tegra30-cardhu-a02.dts b/arch/arm/boot/dts/tegra30-cardhu-a02.dts
deleted file mode 100644
index a02ec5082287..000000000000
--- a/arch/arm/boot/dts/tegra30-cardhu-a02.dts
+++ /dev/null
@@ -1,95 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include "tegra30-cardhu.dtsi"
-
-/* This dts file support the cardhu A02 version of board */
-
-/ {
-	model = "NVIDIA Tegra30 Cardhu A02 evaluation board";
-	compatible = "nvidia,cardhu-a02", "nvidia,cardhu", "nvidia,tegra30";
-
-	sdhci@78000400 {
-		status = "okay";
-		power-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
-		bus-width = <4>;
-		keep-power-in-suspend;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ddr_reg: regulator@100 {
-			compatible = "regulator-fixed";
-			reg = <100>;
-			regulator-name = "vdd_ddr";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
-		};
-
-		sys_3v3_reg: regulator@101 {
-			compatible = "regulator-fixed";
-			reg = <101>;
-			regulator-name = "sys_3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
-		};
-
-		usb1_vbus_reg: regulator@102 {
-			compatible = "regulator-fixed";
-			reg = <102>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(I, 4) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_reg>;
-		};
-
-		usb3_vbus_reg: regulator@103 {
-			compatible = "regulator-fixed";
-			reg = <103>;
-			regulator-name = "usb3_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_reg>;
-		};
-
-		vdd_5v0_reg: regulator@104 {
-			compatible = "regulator-fixed";
-			reg = <104>;
-			regulator-name = "5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
-		};
-
-		vdd_bl_reg: regulator@105 {
-			compatible = "regulator-fixed";
-			reg = <105>;
-			regulator-name = "vdd_bl";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(K, 3) GPIO_ACTIVE_HIGH>;
-		};
-	};
-};
-
diff --git a/arch/arm/boot/dts/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
deleted file mode 100644
index 9234988624ec..000000000000
--- a/arch/arm/boot/dts/tegra30-cardhu-a04.dts
+++ /dev/null
@@ -1,154 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include "tegra30-cardhu.dtsi"
-#include "tegra30-cpu-opp.dtsi"
-#include "tegra30-cpu-opp-microvolt.dtsi"
-
-/* This dts file support the cardhu A04 and later versions of board */
-
-/ {
-	model = "NVIDIA Tegra30 Cardhu A04 (A05, A06, A07) evaluation board";
-	compatible = "nvidia,cardhu-a04", "nvidia,cardhu", "nvidia,tegra30";
-
-	sdhci@78000400 {
-		status = "okay";
-		power-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
-		bus-width = <4>;
-		keep-power-in-suspend;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ddr_reg: regulator@100 {
-			compatible = "regulator-fixed";
-			regulator-name = "ddr";
-			reg = <100>;
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
-		};
-
-		sys_3v3_reg: regulator@101 {
-			compatible = "regulator-fixed";
-			reg = <101>;
-			regulator-name = "sys_3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
-		};
-
-		usb1_vbus_reg: regulator@102 {
-			compatible = "regulator-fixed";
-			reg = <102>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(DD, 6) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_reg>;
-		};
-
-		usb3_vbus_reg: regulator@103 {
-			compatible = "regulator-fixed";
-			reg = <103>;
-			regulator-name = "usb3_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(DD, 4) GPIO_ACTIVE_HIGH>;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_reg>;
-		};
-
-		vdd_5v0_reg: regulator@104 {
-			compatible = "regulator-fixed";
-			reg = <104>;
-			regulator-name = "5v0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
-		};
-
-		vdd_bl_reg: regulator@105 {
-			compatible = "regulator-fixed";
-			reg = <105>;
-			regulator-name = "vdd_bl";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(DD, 2) GPIO_ACTIVE_HIGH>;
-		};
-
-		vdd_bl2_reg: regulator@106 {
-			compatible = "regulator-fixed";
-			reg = <106>;
-			regulator-name = "vdd_bl2";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			enable-active-high;
-			gpio = <&gpio TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	i2c@7000d000 {
-		pmic: tps65911@2d {
-			regulators {
-				vddctrl_reg: vddctrl {
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1125000>;
-					regulator-coupled-with = <&vddcore_reg>;
-					regulator-coupled-max-spread = <300000>;
-					regulator-max-step-microvolt = <100000>;
-
-					nvidia,tegra-cpu-regulator;
-				};
-			};
-		};
-
-		vddcore_reg: tps62361@60 {
-			regulator-coupled-with = <&vddctrl_reg>;
-			regulator-coupled-max-spread = <300000>;
-			regulator-max-step-microvolt = <100000>;
-
-			nvidia,tegra-core-regulator;
-		};
-	};
-
-	cpus {
-		cpu0: cpu@0 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@1 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@2 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@3 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi
deleted file mode 100644
index 5c40ef49894f..000000000000
--- a/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi
+++ /dev/null
@@ -1,801 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-/ {
-	cpu0_opp_table: cpu_opp_table0 {
-		opp@51000000_800 {
-			opp-microvolt = <800000 800000 1250000>;
-		};
-
-		opp@51000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@51000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@102000000_800 {
-			opp-microvolt = <800000 800000 1250000>;
-		};
-
-		opp@102000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@102000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@204000000_800 {
-			opp-microvolt = <800000 800000 1250000>;
-		};
-
-		opp@204000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@204000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@312000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@312000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@340000000_800 {
-			opp-microvolt = <800000 800000 1250000>;
-		};
-
-		opp@340000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@370000000_800 {
-			opp-microvolt = <800000 800000 1250000>;
-		};
-
-		opp@456000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@456000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@475000000_800 {
-			opp-microvolt = <800000 800000 1250000>;
-		};
-
-		opp@475000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@475000000_850_0_1 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@475000000_850_0_4 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@475000000_850_0_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@475000000_850_0_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@608000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@608000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@620000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_1_1 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_2_1 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_3_1 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_1_4 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_2_4 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_3_4 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_1_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_2_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_3_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_4_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_1_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_2_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_3_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_850_4_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@640000000_900 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_3_1 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_3_2 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_3_3 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_3_4 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_3_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_4_7 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_3_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_4_8 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_850_0_10 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@760000000_900 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_1_1 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_2_1 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_1_2 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_2_2 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_1_3 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_2_3 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_1_4 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_2_4 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_1_7 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_2_7 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_1_8 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_900_2_8 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@760000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@760000000_975 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@816000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@816000000_912 {
-			opp-microvolt = <912000 912000 1250000>;
-		};
-
-		opp@860000000_850 {
-			opp-microvolt = <850000 850000 1250000>;
-		};
-
-		opp@860000000_900 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_2_1 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_3_1 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_2_2 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_3_2 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_2_3 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_3_3 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_2_4 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_3_4 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_2_7 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_3_7 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_4_7 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_2_8 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_3_8 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_900_4_8 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@860000000_975 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_975_1_1 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_975_1_2 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_975_1_3 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_975_1_4 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_975_1_7 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_975_1_8 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@860000000_1000 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@910000000_900 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@1000000000_900 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@1000000000_975 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_2_1 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_3_1 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_2_2 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_3_2 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_2_3 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_3_3 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_2_4 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_3_4 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_2_7 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_3_7 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_4_7 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_2_8 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_3_8 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_975_4_8 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1000000000_1000 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1000000000_1025 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1100000000_900 {
-			opp-microvolt = <900000 900000 1250000>;
-		};
-
-		opp@1100000000_975 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_3_1 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_3_2 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_3_3 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_3_4 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_3_7 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_4_7 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_3_8 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_975_4_8 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1100000000_1000 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1000_2_1 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1000_2_2 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1000_2_3 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1000_2_4 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1000_2_7 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1000_2_8 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1100000000_1025 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1100000000_1075 {
-			opp-microvolt = <1075000 1075000 1250000>;
-		};
-
-		opp@1150000000_975 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1200000000_975 {
-			opp-microvolt = <975000 975000 1250000>;
-		};
-
-		opp@1200000000_1000 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_3_1 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_3_2 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_3_3 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_3_4 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_3_7 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_4_7 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_3_8 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1000_4_8 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1200000000_1025 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1025_2_1 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1025_2_2 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1025_2_3 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1025_2_4 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1025_2_7 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1025_2_8 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1200000000_1050 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1200000000_1075 {
-			opp-microvolt = <1075000 1075000 1250000>;
-		};
-
-		opp@1200000000_1100 {
-			opp-microvolt = <1100000 1100000 1250000>;
-		};
-
-		opp@1300000000_1000 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1300000000_1000_4_7 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1300000000_1000_4_8 {
-			opp-microvolt = <1000000 1000000 1250000>;
-		};
-
-		opp@1300000000_1025 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1300000000_1025_3_1 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1300000000_1025_3_7 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1300000000_1025_3_8 {
-			opp-microvolt = <1025000 1025000 1250000>;
-		};
-
-		opp@1300000000_1050 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_2_1 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_2 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_3 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_4 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_5 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_6 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_2_7 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_2_8 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_12 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1050_3_13 {
-			opp-microvolt = <1050000 1050000 1250000>;
-		};
-
-		opp@1300000000_1075 {
-			opp-microvolt = <1075000 1075000 1250000>;
-		};
-
-		opp@1300000000_1075_2_2 {
-			opp-microvolt = <1075000 1075000 1250000>;
-		};
-
-		opp@1300000000_1075_2_3 {
-			opp-microvolt = <1075000 1075000 1250000>;
-		};
-
-		opp@1300000000_1075_2_4 {
-			opp-microvolt = <1075000 1075000 1250000>;
-		};
-
-		opp@1300000000_1100 {
-			opp-microvolt = <1100000 1100000 1250000>;
-		};
-
-		opp@1300000000_1125 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1300000000_1150 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1300000000_1175 {
-			opp-microvolt = <1175000 1175000 1250000>;
-		};
-
-		opp@1400000000_1100 {
-			opp-microvolt = <1100000 1100000 1250000>;
-		};
-
-		opp@1400000000_1125 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1400000000_1150 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1400000000_1150_2_4 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1400000000_1175 {
-			opp-microvolt = <1175000 1175000 1250000>;
-		};
-
-		opp@1400000000_1237 {
-			opp-microvolt = <1237000 1237000 1250000>;
-		};
-
-		opp@1500000000_1125 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1500000000_1125_4_5 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1500000000_1125_4_6 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1500000000_1125_4_12 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1500000000_1125_4_13 {
-			opp-microvolt = <1125000 1125000 1250000>;
-		};
-
-		opp@1500000000_1150 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1500000000_1150_3_5 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1500000000_1150_3_6 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1500000000_1150_3_12 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1500000000_1150_3_13 {
-			opp-microvolt = <1150000 1150000 1250000>;
-		};
-
-		opp@1500000000_1200 {
-			opp-microvolt = <1200000 1200000 1250000>;
-		};
-
-		opp@1500000000_1237 {
-			opp-microvolt = <1237000 1237000 1250000>;
-		};
-
-		opp@1600000000_1212 {
-			opp-microvolt = <1212000 1212000 1250000>;
-		};
-
-		opp@1600000000_1237 {
-			opp-microvolt = <1237000 1237000 1250000>;
-		};
-
-		opp@1700000000_1212 {
-			opp-microvolt = <1212000 1212000 1250000>;
-		};
-
-		opp@1700000000_1237 {
-			opp-microvolt = <1237000 1237000 1250000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi b/arch/arm/boot/dts/tegra30-cpu-opp.dtsi
deleted file mode 100644
index d64fc262585e..000000000000
--- a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi
+++ /dev/null
@@ -1,1202 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-/ {
-	cpu0_opp_table: cpu_opp_table0 {
-		compatible = "operating-points-v2";
-		opp-shared;
-
-		opp@51000000_800 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x31FE>;
-			opp-hz = /bits/ 64 <51000000>;
-		};
-
-		opp@51000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0C01>;
-			opp-hz = /bits/ 64 <51000000>;
-		};
-
-		opp@51000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <51000000>;
-		};
-
-		opp@102000000_800 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x31FE>;
-			opp-hz = /bits/ 64 <102000000>;
-		};
-
-		opp@102000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0C01>;
-			opp-hz = /bits/ 64 <102000000>;
-		};
-
-		opp@102000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <102000000>;
-		};
-
-		opp@204000000_800 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x31FE>;
-			opp-hz = /bits/ 64 <204000000>;
-		};
-
-		opp@204000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0C01>;
-			opp-hz = /bits/ 64 <204000000>;
-		};
-
-		opp@204000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <204000000>;
-		};
-
-		opp@312000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0C00>;
-			opp-hz = /bits/ 64 <312000000>;
-		};
-
-		opp@312000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <312000000>;
-		};
-
-		opp@340000000_800 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0192>;
-			opp-hz = /bits/ 64 <340000000>;
-		};
-
-		opp@340000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x0F 0x0001>;
-			opp-hz = /bits/ 64 <340000000>;
-		};
-
-		opp@370000000_800 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1E 0x306C>;
-			opp-hz = /bits/ 64 <370000000>;
-		};
-
-		opp@456000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0C00>;
-			opp-hz = /bits/ 64 <456000000>;
-		};
-
-		opp@456000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <456000000>;
-		};
-
-		opp@475000000_800 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1E 0x31FE>;
-			opp-hz = /bits/ 64 <475000000>;
-		};
-
-		opp@475000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x0F 0x0001>;
-			opp-hz = /bits/ 64 <475000000>;
-		};
-
-		opp@475000000_850_0_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0002>;
-			opp-hz = /bits/ 64 <475000000>;
-		};
-
-		opp@475000000_850_0_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0010>;
-			opp-hz = /bits/ 64 <475000000>;
-		};
-
-		opp@475000000_850_0_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0080>;
-			opp-hz = /bits/ 64 <475000000>;
-		};
-
-		opp@475000000_850_0_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0100>;
-			opp-hz = /bits/ 64 <475000000>;
-		};
-
-		opp@608000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0400>;
-			opp-hz = /bits/ 64 <608000000>;
-		};
-
-		opp@608000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <608000000>;
-		};
-
-		opp@620000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1E 0x306C>;
-			opp-hz = /bits/ 64 <620000000>;
-		};
-
-		opp@640000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x0F 0x0001>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_1_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0002>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_1_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0010>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_1_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0080>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_1_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0100>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_850_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@640000000_900 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0192>;
-			opp-hz = /bits/ 64 <640000000>;
-		};
-
-		opp@760000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1E 0x3461>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_3_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_3_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0008>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_850_0_10 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0400>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0001>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_1_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0002>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_1_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0004>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_2_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_1_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0008>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_2_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0008>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_1_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0010>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_1_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0080>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_1_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0100>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_900_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@760000000_975 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0192>;
-			opp-hz = /bits/ 64 <760000000>;
-		};
-
-		opp@816000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0400>;
-			opp-hz = /bits/ 64 <816000000>;
-		};
-
-		opp@816000000_912 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x1F 0x0200>;
-			opp-hz = /bits/ 64 <816000000>;
-		};
-
-		opp@860000000_850 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x0C 0x0001>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0001>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_2_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_3_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_2_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0008>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_3_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0008>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_900_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0001>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975_1_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0002>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975_1_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0004>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975_1_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0008>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975_1_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0010>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975_1_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0080>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_975_1_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0100>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@860000000_1000 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0192>;
-			opp-hz = /bits/ 64 <860000000>;
-		};
-
-		opp@910000000_900 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x18 0x3060>;
-			opp-hz = /bits/ 64 <910000000>;
-		};
-
-		opp@1000000000_900 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x0C 0x0001>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x03 0x0001>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_2_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_3_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_2_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0008>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_3_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0008>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_975_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_1000 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x019E>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1000000000_1025 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0192>;
-			opp-hz = /bits/ 64 <1000000000>;
-		};
-
-		opp@1100000000_900 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0001>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x06 0x0001>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_3_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_3_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0008>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_975_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0001>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000_2_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000_2_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0008>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1000_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1025 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x019E>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1100000000_1075 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0192>;
-			opp-hz = /bits/ 64 <1100000000>;
-		};
-
-		opp@1150000000_975 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x18 0x3060>;
-			opp-hz = /bits/ 64 <1150000000>;
-		};
-
-		opp@1200000000_975 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0001>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0001>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_3_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_3_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0008>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1000_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0001>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025_2_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025_2_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0008>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1025_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1050 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x019E>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1075 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0001>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1200000000_1100 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0192>;
-			opp-hz = /bits/ 64 <1200000000>;
-		};
-
-		opp@1300000000_1000 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0001>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1000_4_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0080>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1000_4_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0100>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1025 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0001>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1025_3_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0002>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1025_3_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0080>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1025_3_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0100>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x12 0x3061>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_2_1 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0002>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0004>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0008>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_5 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0020>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_6 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0040>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_2_7 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0080>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_2_8 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0100>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_12 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x1000>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1050_3_13 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x2000>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1075 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0182>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1075_2_2 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0004>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1075_2_3 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0008>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1075_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1100 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x001C>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1125 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0001>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1150 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0182>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1300000000_1175 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0010>;
-			opp-hz = /bits/ 64 <1300000000>;
-		};
-
-		opp@1400000000_1100 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x18 0x307C>;
-			opp-hz = /bits/ 64 <1400000000>;
-		};
-
-		opp@1400000000_1125 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x000C>;
-			opp-hz = /bits/ 64 <1400000000>;
-		};
-
-		opp@1400000000_1150 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x000C>;
-			opp-hz = /bits/ 64 <1400000000>;
-		};
-
-		opp@1400000000_1150_2_4 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <1400000000>;
-		};
-
-		opp@1400000000_1175 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0010>;
-			opp-hz = /bits/ 64 <1400000000>;
-		};
-
-		opp@1400000000_1237 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0010>;
-			opp-hz = /bits/ 64 <1400000000>;
-		};
-
-		opp@1500000000_1125 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0010>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1125_4_5 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0020>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1125_4_6 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x0040>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1125_4_12 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x1000>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1125_4_13 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x2000>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1150 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x04 0x0010>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1150_3_5 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0020>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1150_3_6 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x0040>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1150_3_12 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x1000>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1150_3_13 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x2000>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1200 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x02 0x0010>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1500000000_1237 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x01 0x0010>;
-			opp-hz = /bits/ 64 <1500000000>;
-		};
-
-		opp@1600000000_1212 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x3060>;
-			opp-hz = /bits/ 64 <1600000000>;
-		};
-
-		opp@1600000000_1237 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x3060>;
-			opp-hz = /bits/ 64 <1600000000>;
-		};
-
-		opp@1700000000_1212 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x10 0x3060>;
-			opp-hz = /bits/ 64 <1700000000>;
-		};
-
-		opp@1700000000_1237 {
-			clock-latency-ns = <100000>;
-			opp-supported-hw = <0x08 0x3060>;
-			opp-hz = /bits/ 64 <1700000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ti/Makefile b/arch/arm/boot/dts/ti/Makefile
new file mode 100644
index 000000000000..871079a7bc3b
--- /dev/null
+++ b/arch/arm/boot/dts/ti/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += davinci
+subdir-y += keystone
+subdir-y += omap
diff --git a/arch/arm/boot/dts/ti/davinci/Makefile b/arch/arm/boot/dts/ti/davinci/Makefile
new file mode 100644
index 000000000000..c0e388eb3dd1
--- /dev/null
+++ b/arch/arm/boot/dts/ti/davinci/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_DAVINCI) += \
+	da850-lcdk.dtb \
+	da850-enbw-cmc.dtb \
+	da850-evm.dtb \
+	da850-lego-ev3.dtb
diff --git a/arch/arm/boot/dts/da850-enbw-cmc.dts b/arch/arm/boot/dts/ti/davinci/da850-enbw-cmc.dts
index d4a5237cee0a..d4a5237cee0a 100644
--- a/arch/arm/boot/dts/da850-enbw-cmc.dts
+++ b/arch/arm/boot/dts/ti/davinci/da850-enbw-cmc.dts
diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/ti/davinci/da850-evm.dts
index f2e7609e5346..6c5936278e75 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/ti/davinci/da850-evm.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree for DA850 EVM board
  *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 #include "da850.dtsi"
@@ -52,15 +52,15 @@
 		enable-gpios = <&gpio 40 GPIO_ACTIVE_HIGH>; /* lcd_panel_pwr */
 
 		panel-info {
-			ac-bias		= <255>;
-			ac-bias-intrpt	= <0>;
-			dma-burst-sz	= <16>;
-			bpp		= <16>;
-			fdd		= <0x80>;
-			sync-edge	= <0>;
-			sync-ctrl	= <1>;
-			raster-order	= <0>;
-			fifo-th		= <0>;
+			ac-bias = <255>;
+			ac-bias-intrpt = <0>;
+			dma-burst-sz = <16>;
+			bpp = <16>;
+			fdd = <0x80>;
+			sync-edge = <0>;
+			sync-ctrl = <1>;
+			raster-order = <0>;
+			fifo-th = <0>;
 		};
 
 		display-timings {
@@ -161,7 +161,7 @@
 &pmx_core {
 	status = "okay";
 
-	mcasp0_pins: pinmux_mcasp0_pins {
+	mcasp0_pins: mcasp0-pins {
 		pinctrl-single,bits = <
 			/*
 			 * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
@@ -172,7 +172,7 @@
 			0x04 0x00011000 0x000ff000
 		>;
 	};
-	nand_pins: nand_pins {
+	nand_pins: nand-pins {
 		pinctrl-single,bits = <
 			/* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
 			0x1c 0x10110110  0xf0ff0ff0
@@ -278,7 +278,7 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -333,7 +333,7 @@
 	status = "okay";
 };
 
-/include/ "tps6507x.dtsi"
+/include/ "../../tps6507x.dtsi"
 
 &tps {
 	vdcdc1_2-supply = <&vbat>;
@@ -415,7 +415,7 @@
 &aemif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_pins>;
-	status = "ok";
+	status = "okay";
 	cs3 {
 		#address-cells = <2>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/ti/davinci/da850-lcdk.dts
index e379d6e7ad49..8390d71b000a 100644
--- a/arch/arm/boot/dts/da850-lcdk.dts
+++ b/arch/arm/boot/dts/ti/davinci/da850-lcdk.dts
@@ -199,7 +199,7 @@
 &pmx_core {
 	status = "okay";
 
-	mcasp0_pins: pinmux_mcasp0_pins {
+	mcasp0_pins: mcasp0-pins {
 		pinctrl-single,bits = <
 			/* AHCLKX AFSX ACLKX */
 			0x00 0x00101010 0x00f0f0f0
@@ -208,7 +208,7 @@
 		>;
 	};
 
-	nand_pins: nand_pins {
+	nand_pins: nand-pins {
 		pinctrl-single,bits = <
 			/* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[3] */
 			0x1c 0x10110010  0xf0ff00f0
diff --git a/arch/arm/boot/dts/da850-lego-ev3.dts b/arch/arm/boot/dts/ti/davinci/da850-lego-ev3.dts
index afd04a423856..4df10379ff22 100644
--- a/arch/arm/boot/dts/da850-lego-ev3.dts
+++ b/arch/arm/boot/dts/ti/davinci/da850-lego-ev3.dts
@@ -234,7 +234,7 @@
 &pmx_core {
 	status = "okay";
 
-	ev3_lcd_pins: pinmux_lcd {
+	ev3_lcd_pins: lcd-pins {
 		pinctrl-single,bits = <
 			/* SIMO, CLK */
 			0x14 0x00100100 0x00f00f00
@@ -391,7 +391,7 @@
 	pinctrl-names = "default";
 	cs-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
 
-	display@0{
+	display@0 {
 		compatible = "lego,ev3-lcd";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/ti/davinci/da850.dtsi
index 7cf31b6e48b7..f759fdfe1b10 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/ti/davinci/da850.dtsi
@@ -170,55 +170,55 @@
 				#pinctrl-single,gpio-range-cells = <3>;
 			};
 
-			serial0_rtscts_pins: pinmux_serial0_rtscts_pins {
+			serial0_rtscts_pins: serial0-rtscts-pins {
 				pinctrl-single,bits = <
 					/* UART0_RTS UART0_CTS */
 					0x0c 0x22000000 0xff000000
 				>;
 			};
-			serial0_rxtx_pins: pinmux_serial0_rxtx_pins {
+			serial0_rxtx_pins: serial0-rxtx-pins {
 				pinctrl-single,bits = <
 					/* UART0_TXD UART0_RXD */
 					0x0c 0x00220000 0x00ff0000
 				>;
 			};
-			serial1_rtscts_pins: pinmux_serial1_rtscts_pins {
+			serial1_rtscts_pins: serial1-rtscts-pins {
 				pinctrl-single,bits = <
 					/* UART1_CTS UART1_RTS */
 					0x00 0x00440000 0x00ff0000
 				>;
 			};
-			serial1_rxtx_pins: pinmux_serial1_rxtx_pins {
+			serial1_rxtx_pins: serial1-rxtx-pins {
 				pinctrl-single,bits = <
 					/* UART1_TXD UART1_RXD */
 					0x10 0x22000000 0xff000000
 				>;
 			};
-			serial2_rtscts_pins: pinmux_serial2_rtscts_pins {
+			serial2_rtscts_pins: serial2-rtscts-pins {
 				pinctrl-single,bits = <
 					/* UART2_CTS UART2_RTS */
 					0x00 0x44000000 0xff000000
 				>;
 			};
-			serial2_rxtx_pins: pinmux_serial2_rxtx_pins {
+			serial2_rxtx_pins: serial2-rxtx-pins {
 				pinctrl-single,bits = <
 					/* UART2_TXD UART2_RXD */
 					0x10 0x00220000 0x00ff0000
 				>;
 			};
-			i2c0_pins: pinmux_i2c0_pins {
+			i2c0_pins: i2c0-pins {
 				pinctrl-single,bits = <
 					/* I2C0_SDA,I2C0_SCL */
 					0x10 0x00002200 0x0000ff00
 				>;
 			};
-			i2c1_pins: pinmux_i2c1_pins {
+			i2c1_pins: i2c1-pins {
 				pinctrl-single,bits = <
 					/* I2C1_SDA, I2C1_SCL */
 					0x10 0x00440000 0x00ff0000
 				>;
 			};
-			mmc0_pins: pinmux_mmc_pins {
+			mmc0_pins: mmc-pins {
 				pinctrl-single,bits = <
 					/* MMCSD0_DAT[3] MMCSD0_DAT[2]
 					 * MMCSD0_DAT[1] MMCSD0_DAT[0]
@@ -227,85 +227,85 @@
 					0x28 0x00222222  0x00ffffff
 				>;
 			};
-			ehrpwm0a_pins: pinmux_ehrpwm0a_pins {
+			ehrpwm0a_pins: ehrpwm0a-pins {
 				pinctrl-single,bits = <
 					/* EPWM0A */
 					0xc 0x00000002 0x0000000f
 				>;
 			};
-			ehrpwm0b_pins: pinmux_ehrpwm0b_pins {
+			ehrpwm0b_pins: ehrpwm0b-pins {
 				pinctrl-single,bits = <
 					/* EPWM0B */
 					0xc 0x00000020 0x000000f0
 				>;
 			};
-			ehrpwm1a_pins: pinmux_ehrpwm1a_pins {
+			ehrpwm1a_pins: ehrpwm1a-pins {
 				pinctrl-single,bits = <
 					/* EPWM1A */
 					0x14 0x00000002 0x0000000f
 				>;
 			};
-			ehrpwm1b_pins: pinmux_ehrpwm1b_pins {
+			ehrpwm1b_pins: ehrpwm1b-pins {
 				pinctrl-single,bits = <
 					/* EPWM1B */
 					0x14 0x00000020 0x000000f0
 				>;
 			};
-			ecap0_pins: pinmux_ecap0_pins {
+			ecap0_pins: ecap0-pins {
 				pinctrl-single,bits = <
 					/* ECAP0_APWM0 */
 					0x8 0x20000000 0xf0000000
 				>;
 			};
-			ecap1_pins: pinmux_ecap1_pins {
+			ecap1_pins: ecap1-pins {
 				pinctrl-single,bits = <
 					/* ECAP1_APWM1 */
 					0x4 0x40000000 0xf0000000
 				>;
 			};
-			ecap2_pins: pinmux_ecap2_pins {
+			ecap2_pins: ecap2-pins {
 				pinctrl-single,bits = <
 					/* ECAP2_APWM2 */
 					0x4 0x00000004 0x0000000f
 				>;
 			};
-			spi0_pins: pinmux_spi0_pins {
+			spi0_pins: spi0-pins {
 				pinctrl-single,bits = <
 					/* SIMO, SOMI, CLK */
 					0xc 0x00001101 0x0000ff0f
 				>;
 			};
-			spi0_cs0_pin: pinmux_spi0_cs0 {
+			spi0_cs0_pin: spi0-cs0-pins {
 				pinctrl-single,bits = <
 					/* CS0 */
 					0x10 0x00000010 0x000000f0
 				>;
 			};
-			spi0_cs3_pin: pinmux_spi0_cs3_pin {
+			spi0_cs3_pin: spi0-cs3-pins {
 				pinctrl-single,bits = <
 					/* CS3 */
 					0xc 0x01000000 0x0f000000
 				>;
 			};
-			spi1_pins: pinmux_spi1_pins {
+			spi1_pins: spi1-pins {
 				pinctrl-single,bits = <
 					/* SIMO, SOMI, CLK */
 					0x14 0x00110100 0x00ff0f00
 				>;
 			};
-			spi1_cs0_pin: pinmux_spi1_cs0 {
+			spi1_cs0_pin: spi1-cs0-pins {
 				pinctrl-single,bits = <
 					/* CS0 */
 					0x14 0x00000010 0x000000f0
 				>;
 			};
-			mdio_pins: pinmux_mdio_pins {
+			mdio_pins: mdio-pins {
 				pinctrl-single,bits = <
 					/* MDIO_CLK, MDIO_D */
 					0x10 0x00000088 0x000000ff
 				>;
 			};
-			mii_pins: pinmux_mii_pins {
+			mii_pins: mii-pins {
 				pinctrl-single,bits = <
 					/*
 					 * MII_TXEN, MII_TXCLK, MII_COL
@@ -321,7 +321,7 @@
 					0xc 0x88888888 0xffffffff
 				>;
 			};
-			lcd_pins: pinmux_lcd_pins {
+			lcd_pins: lcd-pins {
 				pinctrl-single,bits = <
 					/*
 					 * LCD_D[2], LCD_D[3], LCD_D[4], LCD_D[5],
@@ -342,7 +342,7 @@
 					0x4c 0x02000022 0x0f0000ff
 				>;
 			};
-			vpif_capture_pins: vpif_capture_pins {
+			vpif_capture_pins: vpif-capture-pins {
 				pinctrl-single,bits = <
 					/* VP_DIN[2..7], VP_CLKIN1, VP_CLKIN0 */
 					0x38 0x11111111 0xffffffff
@@ -352,7 +352,7 @@
 					0x40 0x00000011 0x000000ff
 				>;
 			};
-			vpif_display_pins: vpif_display_pins {
+			vpif_display_pins: vpif-display-pins {
 				pinctrl-single,bits = <
 					/* VP_DOUT[2..7] */
 					0x40 0x11111100 0xffffff00
@@ -419,9 +419,9 @@
 		edma0: edma@0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
-			reg =	<0x0 0x8000>;
+			reg = <0x0 0x8000>;
 			reg-names = "edma3_cc";
-			interrupts = <11 12>;
+			interrupts = <11>, <12>;
 			interrupt-names = "edma3_ccint", "edma3_ccerrint";
 			#dma-cells = <2>;
 
@@ -430,14 +430,14 @@
 		};
 		edma0_tptc0: tptc@8000 {
 			compatible = "ti,edma3-tptc";
-			reg =	<0x8000 0x400>;
+			reg = <0x8000 0x400>;
 			interrupts = <13>;
 			interrupt-names = "edm3_tcerrint";
 			power-domains = <&psc0 1>;
 		};
 		edma0_tptc1: tptc@8400 {
 			compatible = "ti,edma3-tptc";
-			reg =	<0x8400 0x400>;
+			reg = <0x8400 0x400>;
 			interrupts = <32>;
 			interrupt-names = "edm3_tcerrint";
 			power-domains = <&psc0 2>;
@@ -445,9 +445,9 @@
 		edma1: edma@230000 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC1: 0x01e3 0000 - 0x01e3 7fff */
-			reg =	<0x230000 0x8000>;
+			reg = <0x230000 0x8000>;
 			reg-names = "edma3_cc";
-			interrupts = <93 94>;
+			interrupts = <93>, <94>;
 			interrupt-names = "edma3_ccint", "edma3_ccerrint";
 			#dma-cells = <2>;
 
@@ -456,7 +456,7 @@
 		};
 		edma1_tptc0: tptc@238000 {
 			compatible = "ti,edma3-tptc";
-			reg =	<0x238000 0x400>;
+			reg = <0x238000 0x400>;
 			interrupts = <95>;
 			interrupt-names = "edm3_tcerrint";
 			power-domains = <&psc1 21>;
@@ -494,8 +494,7 @@
 		rtc0: rtc@23000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x23000 0x1000>;
-			interrupts = <19
-				      19>;
+			interrupts = <19>, <19>;
 			clocks = <&pll0_auxclk>;
 			clock-names = "int-clk";
 			status = "disabled";
@@ -574,8 +573,7 @@
 			status = "disabled";
 		};
 		ehrpwm0: pwm@300000 {
-			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm",
-				     "ti,am33xx-ehrpwm";
+			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm";
 			#pwm-cells = <3>;
 			reg = <0x300000 0x2000>;
 			clocks = <&psc1 17>, <&ehrpwm_tbclk>;
@@ -584,8 +582,7 @@
 			status = "disabled";
 		};
 		ehrpwm1: pwm@302000 {
-			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm",
-				     "ti,am33xx-ehrpwm";
+			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm";
 			#pwm-cells = <3>;
 			reg = <0x302000 0x2000>;
 			clocks = <&psc1 17>, <&ehrpwm_tbclk>;
@@ -593,9 +590,8 @@
 			power-domains = <&psc1 17>;
 			status = "disabled";
 		};
-		ecap0: ecap@306000 {
-			compatible = "ti,da850-ecap", "ti,am3352-ecap",
-				     "ti,am33xx-ecap";
+		ecap0: pwm@306000 {
+			compatible = "ti,da850-ecap", "ti,am3352-ecap";
 			#pwm-cells = <3>;
 			reg = <0x306000 0x80>;
 			clocks = <&psc1 20>;
@@ -603,9 +599,8 @@
 			power-domains = <&psc1 20>;
 			status = "disabled";
 		};
-		ecap1: ecap@307000 {
-			compatible = "ti,da850-ecap", "ti,am3352-ecap",
-				     "ti,am33xx-ecap";
+		ecap1: pwm@307000 {
+			compatible = "ti,da850-ecap", "ti,am3352-ecap";
 			#pwm-cells = <3>;
 			reg = <0x307000 0x80>;
 			clocks = <&psc1 20>;
@@ -613,9 +608,8 @@
 			power-domains = <&psc1 20>;
 			status = "disabled";
 		};
-		ecap2: ecap@308000 {
-			compatible = "ti,da850-ecap", "ti,am3352-ecap",
-				     "ti,am33xx-ecap";
+		ecap2: pwm@308000 {
+			compatible = "ti,da850-ecap", "ti,am3352-ecap";
 			#pwm-cells = <3>;
 			reg = <0x308000 0x80>;
 			clocks = <&psc1 20>;
@@ -677,14 +671,16 @@
 
 			cppi41dma: dma-controller@201000 {
 				compatible = "ti,da830-cppi41";
-				reg =  <0x201000 0x1000
+				reg = <0x201000 0x1000
 					0x202000 0x1000
 					0x204000 0x4000>;
 				reg-names = "controller",
 					    "scheduler", "queuemgr";
 				interrupts = <58>;
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <4>;
+				dma-channels = <4>;
 				power-domains = <&psc1 1>;
 				status = "okay";
 			};
@@ -728,11 +724,7 @@
 			ti,davinci-ctrl-ram-offset = <0>;
 			ti,davinci-ctrl-ram-size = <0x2000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <33
-					34
-					35
-					36
-					>;
+			interrupts = <33>, <34>, <35>,<36>;
 			clocks = <&psc1 5>;
 			power-domains = <&psc1 5>;
 			status = "disabled";
@@ -751,7 +743,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			reg = <0x226000 0x1000>;
-			interrupts = <42 43 44 45 46 47 48 49 50>;
+			interrupts = <42>, <43>, <44>, <45>, <46>, <47>, <48>, <49>, <50>;
 			ti,ngpio = <144>;
 			ti,davinci-gpio-unbanked = <0>;
 			clocks = <&psc1 3>;
diff --git a/arch/arm/boot/dts/ti/keystone/Makefile b/arch/arm/boot/dts/ti/keystone/Makefile
new file mode 100644
index 000000000000..4b18d08fa57c
--- /dev/null
+++ b/arch/arm/boot/dts/ti/keystone/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_KEYSTONE) += \
+	keystone-k2hk-evm.dtb \
+	keystone-k2l-evm.dtb \
+	keystone-k2e-evm.dtb \
+	keystone-k2g-evm.dtb \
+	keystone-k2g-ice.dtb
diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-clocks.dtsi
index 0397c3423d2d..0397c3423d2d 100644
--- a/arch/arm/boot/dts/keystone-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-clocks.dtsi
diff --git a/arch/arm/boot/dts/keystone-k2e-clocks.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2e-clocks.dtsi
index cf30e007fea3..cf30e007fea3 100644
--- a/arch/arm/boot/dts/keystone-k2e-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2e-clocks.dtsi
diff --git a/arch/arm/boot/dts/keystone-k2e-evm.dts b/arch/arm/boot/dts/ti/keystone/keystone-k2e-evm.dts
index 66fec5f5d081..6978d6a362f3 100644
--- a/arch/arm/boot/dts/keystone-k2e-evm.dts
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2e-evm.dts
@@ -78,7 +78,7 @@
 };
 
 &i2c0 {
-	dtt@50 {
+	eeprom@50 {
 		compatible = "atmel,24c1024";
 		reg = <0x50>;
 	};
@@ -130,17 +130,17 @@
 
 			partition@180000 {
 				label = "ubifs";
-				reg = <0x180000 0x1FE80000>;
+				reg = <0x180000 0x1fe80000>;
 			};
 		};
 	};
 };
 
 &spi0 {
-	nor_flash: n25q128a11@0 {
+	nor_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "Micron,n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <54000000>;
 		m25p,fast-read;
 		reg = <0>;
@@ -159,7 +159,7 @@
 };
 
 &mdio {
-	status = "ok";
+	status = "okay";
 	ethphy0: ethernet-phy@0 {
 		compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
diff --git a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2e-netcp.dtsi
index ad15e77874b1..5c88a90903b8 100644
--- a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2e-netcp.dtsi
@@ -12,9 +12,9 @@ qmss: qmss@2a40000 {
 	#size-cells = <1>;
 	clocks = <&chipclk13>;
 	ranges;
-	queue-range	= <0 0x2000>;
-	linkram0	= <0x100000 0x4000>;
-	linkram1	= <0 0x10000>;
+	queue-range = <0 0x2000>;
+	linkram0 = <0x100000 0x4000>;
+	linkram1 = <0 0x10000>;
 
 	qmgrs {
 		#address-cells = <1>;
@@ -36,9 +36,9 @@ qmss: qmss@2a40000 {
 		qpend {
 			qpend-0 {
 				qrange = <658 8>;
-				interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04
-					     0 43 0xf04 0 44 0xf04 0 45 0xf04
-					     0 46 0xf04 0 47 0xf04>;
+				interrupts = <0 40 0xf04 0 41 0xf04 0 42 0xf04
+					      0 43 0xf04 0 44 0xf04 0 45 0xf04
+					      0 46 0xf04 0 47 0xf04>;
 			};
 			qpend-1 {
 				qrange = <528 16>;
@@ -95,7 +95,7 @@ qmss: qmss@2a40000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
-		pdsp0@0x2a10000 {
+		pdsp0@2a10000 {
 			reg = <0x2a10000 0x1000    /*iram */
 			       0x2a0f000 0x100     /*reg*/
 			       0x2a0c000 0x3c8	   /*intd */
@@ -167,7 +167,7 @@ netcp: netcp@24000000 {
 						 <&tsipclka>, <&tsrefclk>,
 						 <&tsipclkb>;
 					ti,mux-tbl = <0x0>, <0x1>, <0x2>,
-						<0x3>, <0x4>, <0x8>, <0xC>;
+						<0x3>, <0x4>, <0x8>, <0xc>;
 					assigned-clocks = <&cpts_refclk_mux>;
 					assigned-clock-parents = <&chipclk12>;
 				};
@@ -176,40 +176,40 @@ netcp: netcp@24000000 {
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy0>;
+					link-interface = <1>;
+					phy-handle = <&ethphy0>;
 				};
 				gbe1: interface-1 {
 					slave-port = <1>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy1>;
+					link-interface = <1>;
+					phy-handle = <&ethphy1>;
 				};
 			};
 
 			secondary-slave-ports {
 				port-2 {
 					slave-port = <2>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-3 {
 					slave-port = <3>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-4 {
 					slave-port = <4>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-5 {
 					slave-port = <5>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-6 {
 					slave-port = <6>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-7 {
 					slave-port = <7>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2e.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2e.dtsi
index 085e7326ea8e..65c32946c522 100644
--- a/arch/arm/boot/dts/keystone-k2e.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2e.dtsi
@@ -52,7 +52,7 @@
 
 		usb: usb@2680000 {
 			interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
-			dwc3@2690000 {
+			usb@2690000 {
 				interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
 			};
 		};
@@ -78,22 +78,22 @@
 			dma-ranges;
 			status = "disabled";
 
-			usb1: dwc3@25010000 {
-				compatible = "synopsys,dwc3";
+			usb1: usb@25010000 {
+				compatible = "snps,dwc3";
 				reg = <0x25010000 0x70000>;
 				interrupts = <GIC_SPI 414 IRQ_TYPE_EDGE_RISING>;
 				usb-phy = <&usb1_phy>, <&usb1_phy>;
 			};
 		};
 
-		msm_ram: msmram@c000000 {
+		msm_ram: sram@c000000 {
 			compatible = "mmio-sram";
 			reg = <0x0c000000 0x200000>;
 			ranges = <0x0 0x0c000000 0x200000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			sram-bm@1f0000 {
+			bm-sram@1f0000 {
 				reg = <0x001f0000 0x8000>;
 			};
 		};
@@ -141,7 +141,7 @@
 			clock-names = "pcie";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			reg =  <0x21021000 0x2000>, <0x21020000 0x1000>, <0x02620128 4>;
+			reg = <0x21021000 0x2000>, <0x21020000 0x1000>, <0x02620128 4>;
 			ranges = <0x82000000 0 0x60000000 0x60000000
 				  0 0x10000000>;
 
@@ -185,14 +185,14 @@
 		};
 
 		mdio: mdio@24200f00 {
-			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			compatible = "ti,keystone_mdio", "ti,davinci_mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x24200f00 0x100>;
 			status = "disabled";
 			clocks = <&clkcpgmac>;
 			clock-names = "fck";
-			bus_freq	= <2500000>;
+			bus_freq = <2500000>;
 		};
 		/include/ "keystone-k2e-netcp.dtsi"
 };
diff --git a/arch/arm/boot/dts/keystone-k2g-evm.dts b/arch/arm/boot/dts/ti/keystone/keystone-k2g-evm.dts
index b7f10bf94576..f0ddbbcdc972 100644
--- a/arch/arm/boot/dts/keystone-k2g-evm.dts
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2g-evm.dts
@@ -9,7 +9,7 @@
 #include "keystone-k2g.dtsi"
 
 / {
-	compatible =  "ti,k2g-evm", "ti,k2g", "ti,keystone";
+	compatible = "ti,k2g-evm", "ti,k2g", "ti,keystone";
 	model = "Texas Instruments K2G General Purpose EVM";
 
 	memory@800000000 {
@@ -45,17 +45,89 @@
 		regulator-max-microvolt = <1800000>;
 		regulator-always-on;
 	};
+
+	vcc1v8_ldo2_reg: fixedregulator-vcc1v8-ldo2 {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	hdmi: connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&sii9022_out>;
+			};
+		};
+	};
+
+	aud_mclk: aud_mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12288000>;
+	};
+
+	sound0: sound@0 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "K2G-EVM";
+		simple-audio-card,widgets =
+			"Headphone", "Headphone Jack",
+			"Line", "Line In";
+		simple-audio-card,routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT",
+			"LINE1L",		"Line In",
+			"LINE1R",		"Line In";
+
+		simple-audio-card,dai-link@0 {
+			format = "i2s";
+			bitclock-master = <&sound0_0_master>;
+			frame-master = <&sound0_0_master>;
+			sound0_0_master: cpu {
+				sound-dai = <&mcasp2>;
+				clocks = <&k2g_clks 0x6 1>;
+				system-clock-direction-out;
+			};
+
+			codec {
+				sound-dai = <&tlv320aic3106>;
+				clocks = <&aud_mclk>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			format = "i2s";
+			bitclock-master = <&sound0_1_master>;
+			frame-master = <&sound0_1_master>;
+			sound0_1_master: cpu {
+				sound-dai = <&mcasp2>;
+				clocks = <&k2g_clks 0x6 1>;
+				system-clock-direction-out;
+			};
+
+			codec {
+				sound-dai = <&sii9022>;
+				clocks = <&aud_mclk>;
+			};
+		};
+	};
 };
 
 &k2g_pinctrl {
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x11cc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
 			K2G_CORE_IOPAD(0x11d0) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
 		>;
 	};
 
-	mmc0_pins: pinmux_mmc0_pins {
+	mmc0_pins: mmc0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x1300) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE2)	/* mmc0_dat3.mmc0_dat3 */
 			K2G_CORE_IOPAD(0x1304) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE2)	/* mmc0_dat2.mmc0_dat2 */
@@ -67,7 +139,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x10ec) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat7.mmc1_dat7 */
 			K2G_CORE_IOPAD(0x10f0) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat6.mmc1_dat6 */
@@ -82,20 +154,27 @@
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x137c) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			K2G_CORE_IOPAD(0x1380) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
 		>;
 	};
 
-	ecap0_pins: ecap0_pins {
+	i2c1_pins: i2c1-pins {
+		pinctrl-single,pins = <
+			K2G_CORE_IOPAD(0x1384) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c1_scl.i2c1_scl */
+			K2G_CORE_IOPAD(0x1388) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c1_sda.i2c1_sda */
+		>;
+	};
+
+	ecap0_pins: ecap0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x1374) (BUFFER_CLASS_B | MUX_MODE4)	/* pr1_mdio_data.ecap0_in_apwm0_out */
 		>;
 	};
 
-	spi1_pins: pinmux_spi1_pins {
+	spi1_pins: spi1-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x11a4) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* spi1_scs0.spi1_scs0 */
 			K2G_CORE_IOPAD(0x11ac) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* spi1_clk.spi1_clk */
@@ -104,7 +183,7 @@
 		>;
 	};
 
-	qspi_pins: pinmux_qspi_pins {
+	qspi_pins: qspi-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x1204) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* qspi_clk.qspi_clk */
 			K2G_CORE_IOPAD(0x1208) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* qspi_rclk.qspi_rclk */
@@ -116,50 +195,93 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x11ec) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)      /* uart2_rxd.uart2_rxd */
 			K2G_CORE_IOPAD(0x11f0) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE0)      /* uart2_txd.uart2_txd */
 		>;
 	};
 
-	dcan0_pins: pinmux_dcan0_pins {
+	dcan0_pins: dcan0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x11fc) (BUFFER_CLASS_B | PULL_DISABLE  | MUX_MODE0)	/* dcan0tx.dcan0tx */
 			K2G_CORE_IOPAD(0x1200) (BUFFER_CLASS_B | PIN_PULLDOWN  | MUX_MODE0)	/* dcan0rx.dcan0rx */
 		>;
 	};
 
-	dcan1_pins: pinmux_dcan1_pins {
+	dcan1_pins: dcan1-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x1224) (BUFFER_CLASS_B | PULL_DISABLE  | MUX_MODE1)	/* qspicsn2.dcan1tx */
 			K2G_CORE_IOPAD(0x1228) (BUFFER_CLASS_B | PIN_PULLDOWN  | MUX_MODE1)	/* qspicsn3.dcan1rx */
 		>;
 	};
 
-	emac_pins: pinmux_emac_pins {
+	emac_pins: emac-pins {
 		pinctrl-single,pins = <
-			K2G_CORE_IOPAD(0x113C) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD1.RGMII_RXD1 */
+			K2G_CORE_IOPAD(0x113c) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD1.RGMII_RXD1 */
 			K2G_CORE_IOPAD(0x1138) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD2.RGMII_RXD2 */
 			K2G_CORE_IOPAD(0x1134) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD3.RGMII_RXD3 */
 			K2G_CORE_IOPAD(0x1140) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD0.RGMII_RXD0 */
 			K2G_CORE_IOPAD(0x1178) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD0.RGMII_TXD0 */
 			K2G_CORE_IOPAD(0x1174) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD1.RGMII_TXD1 */
 			K2G_CORE_IOPAD(0x1170) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD2.RGMII_TXD2 */
-			K2G_CORE_IOPAD(0x116C) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD3.RGMII_TXD3 */
+			K2G_CORE_IOPAD(0x116c) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD3.RGMII_TXD3 */
 			K2G_CORE_IOPAD(0x1154) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXCLK.RGMII_TXC */
-			K2G_CORE_IOPAD(0x117C) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXEN.RGMII_TXCTL */
+			K2G_CORE_IOPAD(0x117c) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXEN.RGMII_TXCTL */
 			K2G_CORE_IOPAD(0x1120) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXCLK.RGMII_RXC */
 			K2G_CORE_IOPAD(0x1144) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXDV.RGMII_RXCTL */
 		>;
 	};
 
-	mdio_pins: pinmux_mdio_pins {
+	mdio_pins: mdio-pins {
 		pinctrl-single,pins = <
-			K2G_CORE_IOPAD(0x118C) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* MDIO_CLK.MDIO_CLK */
+			K2G_CORE_IOPAD(0x118c) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* MDIO_CLK.MDIO_CLK */
 			K2G_CORE_IOPAD(0x1188) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* MDIO_DATA.MDIO_DATA */
 		>;
 	};
+
+	vout_pins: vout-pins {
+		pinctrl-single,pins = <
+			K2G_CORE_IOPAD(0x1078) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata23.dssdata23 */
+			K2G_CORE_IOPAD(0x107c) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata22.dssdata22 */
+			K2G_CORE_IOPAD(0x1080) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata21.dssdata21 */
+			K2G_CORE_IOPAD(0x1084) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata20.dssdata20 */
+			K2G_CORE_IOPAD(0x1088) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata19.dssdata19 */
+			K2G_CORE_IOPAD(0x108c) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata18.dssdata18 */
+			K2G_CORE_IOPAD(0x1090) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata17.dssdata17 */
+			K2G_CORE_IOPAD(0x1094) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata16.dssdata16 */
+			K2G_CORE_IOPAD(0x1098) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata15.dssdata15 */
+			K2G_CORE_IOPAD(0x109c) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata14.dssdata14 */
+			K2G_CORE_IOPAD(0x10a0) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata13.dssdata13 */
+			K2G_CORE_IOPAD(0x10a4) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata12.dssdata12 */
+			K2G_CORE_IOPAD(0x10a8) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata11.dssdata11 */
+			K2G_CORE_IOPAD(0x10ac) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata10.dssdata10 */
+			K2G_CORE_IOPAD(0x10b0) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata9.dssdata9 */
+			K2G_CORE_IOPAD(0x10b4) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata8.dssdata8 */
+			K2G_CORE_IOPAD(0x10b8) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata7.dssdata7 */
+			K2G_CORE_IOPAD(0x10bc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata6.dssdata6 */
+			K2G_CORE_IOPAD(0x10c0) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata5.dssdata5 */
+			K2G_CORE_IOPAD(0x10c4) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata4.dssdata4 */
+			K2G_CORE_IOPAD(0x10c8) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata3.dssdata3 */
+			K2G_CORE_IOPAD(0x10cc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata2.dssdata2 */
+			K2G_CORE_IOPAD(0x10d0) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata1.dssdata1 */
+			K2G_CORE_IOPAD(0x10d4) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssdata0.dssdata0 */
+			K2G_CORE_IOPAD(0x10d8) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssvsync.dssvsync */
+			K2G_CORE_IOPAD(0x10dc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dsshsync.dsshsync */
+			K2G_CORE_IOPAD(0x10e0) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dsspclk.dsspclk */
+			K2G_CORE_IOPAD(0x10e4) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssde.dssde */
+			K2G_CORE_IOPAD(0x10e8) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* dssfid.dssfid */
+		>;
+	};
+
+	mcasp2_pins: mcasp2-pins {
+		pinctrl-single,pins = <
+			K2G_CORE_IOPAD(0x1234) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE4) /* pr0_pru_gpo2.mcasp2_axr2 */
+			K2G_CORE_IOPAD(0x1238) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE4) /* pr0_pru_gpo3.mcasp2_axr3 */
+			K2G_CORE_IOPAD(0x1254) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE4) /* pr0_pru_gpo10.mcasp2_afsx */
+			K2G_CORE_IOPAD(0x125c) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE4) /* pr0_pru_gpo12.mcasp2_aclkx */
+		>;
+	};
 };
 
 &uart0 {
@@ -270,7 +392,7 @@
 	pinctrl-0 = <&qspi_pins>;
 	cdns,rclk-en;
 
-	flash0: m25p80@0 {
+	flash0: flash@0 {
 		compatible = "s25fl512s", "jedec,spi-nor";
 		reg = <0>;
 		spi-tx-bus-width = <1>;
@@ -302,11 +424,11 @@
 		};
 		partition@4 {
 			label = "QSPI.kernel";
-			reg = <0x001C0000 0x0800000>;
+			reg = <0x001c0000 0x0800000>;
 		};
 		partition@5 {
 			label = "QSPI.file-system";
-			reg = <0x009C0000 0x3640000>;
+			reg = <0x009c0000 0x3640000>;
 		};
 	};
 };
@@ -348,7 +470,7 @@
 
 &gbe0 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii-id";
+	phy-mode = "rgmii-rxid";
 	status = "okay";
 };
 
@@ -357,3 +479,89 @@
 	pinctrl-0 = <&emac_pins>;
 	status = "okay";
 };
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+	clock-frequency = <400000>;
+
+	sii9022: sii9022@3b {
+		#sound-dai-cells = <0>;
+		compatible = "sil,sii9022";
+		reg = <0x3b>;
+
+		sil,i2s-data-lanes = < 0 >;
+		clocks = <&aud_mclk>;
+		clock-names = "mclk";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022_in: endpoint {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vcc3v3_dcin_reg>;
+		IOVDD-supply = <&vcc3v3_dcin_reg>;
+		DRVDD-supply = <&vcc3v3_dcin_reg>;
+		DVDD-supply = <&vcc1v8_ldo2_reg>;
+	};
+};
+
+&dss {
+	pinctrl-names = "default";
+	pinctrl-0 = <&vout_pins>;
+	status = "okay";
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+&mcasp2 {
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp2_pins>;
+
+	assigned-clocks = <&k2g_clks 0x4c 2>, <&k2g_clks 0x6 1>;
+	assigned-clock-parents = <0>, <&k2g_clks 0x6 2>;
+	assigned-clock-rates = <22579200>, <0>;
+
+	status = "okay";
+
+	op-mode = <0>;		/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	/* 6 serializer */
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+		0 0 1 2 0 0 // AXR2: TX, AXR3: rx
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
diff --git a/arch/arm/boot/dts/keystone-k2g-ice.dts b/arch/arm/boot/dts/ti/keystone/keystone-k2g-ice.dts
index 2a2d38cf0fff..6ceb0d5c6388 100644
--- a/arch/arm/boot/dts/keystone-k2g-ice.dts
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2g-ice.dts
@@ -218,14 +218,14 @@
 };
 
 &k2g_pinctrl {
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x11cc) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
 			K2G_CORE_IOPAD(0x11d0) (BUFFER_CLASS_B | PIN_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
 		>;
 	};
 
-	qspi_pins: pinmux_qspi_pins {
+	qspi_pins: qspi-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x1204) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* qspi_clk.qspi_clk */
 			K2G_CORE_IOPAD(0x1208) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0) /* qspi_rclk.qspi_rclk */
@@ -237,35 +237,35 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
-			K2G_CORE_IOPAD(0x10FC) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat3.mmc1_dat3 */
+			K2G_CORE_IOPAD(0x10fc) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat3.mmc1_dat3 */
 			K2G_CORE_IOPAD(0x1100) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat2.mmc1_dat2 */
 			K2G_CORE_IOPAD(0x1104) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat1.mmc1_dat1 */
 			K2G_CORE_IOPAD(0x1108) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_dat0.mmc1_dat0 */
-			K2G_CORE_IOPAD(0x110C) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
+			K2G_CORE_IOPAD(0x110c) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
 			K2G_CORE_IOPAD(0x1110) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
 			K2G_CORE_IOPAD(0x1114) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE3)	/* mmc1_sdcd.gpio0_69 */
 			K2G_CORE_IOPAD(0x1118) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_sdwp.mmc1_sdwp */
-			K2G_CORE_IOPAD(0x111C) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_pow.mmc1_pow */
+			K2G_CORE_IOPAD(0x111c) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* mmc1_pow.mmc1_pow */
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x137c) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			K2G_CORE_IOPAD(0x1380) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x1384) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c1_scl.i2c1_scl */
 			K2G_CORE_IOPAD(0x1388) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE0)	/* i2c1_sda.i2c1_sda */
 		>;
 	};
 
-	user_leds: pinmux_user_leds {
+	user_leds: user-leds-pins {
 		pinctrl-single,pins = <
 			K2G_CORE_IOPAD(0x102c) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE3)	/* gpmc_ad11.gpio0_11 */
 			K2G_CORE_IOPAD(0x1030) (BUFFER_CLASS_B | PIN_PULLUP | MUX_MODE3)	/* gpmc_ad12.gpio0_12 */
@@ -283,26 +283,26 @@
 		>;
 	};
 
-	emac_pins: pinmux_emac_pins {
+	emac_pins: emac-pins {
 		pinctrl-single,pins = <
-			K2G_CORE_IOPAD(0x113C) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD1.RGMII_RXD1 */
+			K2G_CORE_IOPAD(0x113c) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD1.RGMII_RXD1 */
 			K2G_CORE_IOPAD(0x1138) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD2.RGMII_RXD2 */
 			K2G_CORE_IOPAD(0x1134) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD3.RGMII_RXD3 */
 			K2G_CORE_IOPAD(0x1140) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXD0.RGMII_RXD0 */
 			K2G_CORE_IOPAD(0x1178) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD0.RGMII_TXD0 */
 			K2G_CORE_IOPAD(0x1174) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD1.RGMII_TXD1 */
 			K2G_CORE_IOPAD(0x1170) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD2.RGMII_TXD2 */
-			K2G_CORE_IOPAD(0x116C) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD3.RGMII_TXD3 */
+			K2G_CORE_IOPAD(0x116c) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXD3.RGMII_TXD3 */
 			K2G_CORE_IOPAD(0x1154) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXCLK.RGMII_TXC */
-			K2G_CORE_IOPAD(0x117C) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXEN.RGMII_TXCTL */
+			K2G_CORE_IOPAD(0x117c) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_TXEN.RGMII_TXCTL */
 			K2G_CORE_IOPAD(0x1120) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXCLK.RGMII_RXC */
 			K2G_CORE_IOPAD(0x1144) (BUFFER_CLASS_D | PULL_DISABLE | MUX_MODE1)	/* MII_RXDV.RGMII_RXCTL */
 		>;
 	};
 
-	mdio_pins: pinmux_mdio_pins {
+	mdio_pins: mdio-pins {
 		pinctrl-single,pins = <
-			K2G_CORE_IOPAD(0x118C) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* MDIO_CLK.MDIO_CLK */
+			K2G_CORE_IOPAD(0x118c) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* MDIO_CLK.MDIO_CLK */
 			K2G_CORE_IOPAD(0x1188) (BUFFER_CLASS_B | PULL_DISABLE | MUX_MODE0)	/* MDIO_DATA.MDIO_DATA */
 		>;
 	};
@@ -325,7 +325,7 @@
 	cdns,rclk-en;
 	status = "okay";
 
-	flash0: m25p80@0 {
+	flash0: flash@0 {
 		compatible = "s25fl256s1", "jedec,spi-nor";
 		reg = <0>;
 		spi-tx-bus-width = <1>;
diff --git a/arch/arm/boot/dts/keystone-k2g-netcp.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2g-netcp.dtsi
index d0e6a9a43402..7109ca031617 100644
--- a/arch/arm/boot/dts/keystone-k2g-netcp.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2g-netcp.dtsi
@@ -37,9 +37,9 @@ qmss: qmss@4020000 {
 		qpend {
 			qpend-0 {
 				qrange = <77 8>;
-				interrupts =<0 308 0xf04 0 309 0xf04 0 310 0xf04
-					     0 311 0xf04 0 312 0xf04 0 313 0xf04
-					     0 314 0xf04 0 315 0xf04>;
+				interrupts = <0 308 0xf04 0 309 0xf04 0 310 0xf04
+					      0 311 0xf04 0 312 0xf04 0 313 0xf04
+					      0 314 0xf04 0 315 0xf04>;
 				qalloc-by-id;
 			};
 		};
@@ -125,7 +125,7 @@ netcp: netcp@4000000 {
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
-					link-interface	= <5>;
+					link-interface = <5>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2g.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2g.dtsi
index 1c833105d6c5..102d59694d90 100644
--- a/arch/arm/boot/dts/keystone-k2g.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2g.dtsi
@@ -95,14 +95,14 @@
 		ranges = <0x0 0x0 0x0 0xc0000000>;
 		dma-ranges = <0x80000000 0x8 0x00000000 0x80000000>;
 
-		msm_ram: msmram@c000000 {
+		msm_ram: sram@c000000 {
 			compatible = "mmio-sram";
 			reg = <0x0c000000 0x100000>;
 			ranges = <0x0 0x0c000000 0x100000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			sram-bm@f7000 {
+			bm-sram@f7000 {
 				reg = <0x000f7000 0x8000>;
 			};
 		};
@@ -177,7 +177,7 @@
 
 		dcan0: can@260b200 {
 			compatible = "ti,am4372-d_can", "ti,am3352-d_can";
-			reg = <0x0260B200 0x200>;
+			reg = <0x0260b200 0x200>;
 			interrupts = <GIC_SPI 190 IRQ_TYPE_EDGE_RISING>;
 			status = "disabled";
 			power-domains = <&k2g_pds 0x0008>;
@@ -186,7 +186,7 @@
 
 		dcan1: can@260b400 {
 			compatible = "ti,am4372-d_can", "ti,am3352-d_can";
-			reg = <0x0260B400 0x200>;
+			reg = <0x0260b400 0x200>;
 			interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
 			status = "disabled";
 			power-domains = <&k2g_pds 0x0009>;
@@ -242,7 +242,7 @@
 			status = "disabled";
 		};
 
-		msgmgr: msgmgr@2a00000 {
+		msgmgr: mailbox@2a00000 {
 			compatible = "ti,k2g-message-manager";
 			#mbox-cells = <2>;
 			reg-names = "queue_proxy_region",
@@ -254,7 +254,7 @@
 				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		pmmc: pmmc@2921c00 {
+		pmmc: system-controller@2921c00 {
 			compatible = "ti,k2g-sci";
 			/*
 			 * In case of rare platforms that does not use k2g as
@@ -262,7 +262,7 @@
 			 */
 			ti,system-reboot-controller;
 			mbox-names = "rx", "tx";
-			mboxes= <&msgmgr 5 2>,
+			mboxes = <&msgmgr 5 2>,
 				<&msgmgr 0 0>;
 			reg-names = "debug_messages";
 			reg = <0x02921c00 0x400>;
@@ -272,7 +272,7 @@
 				#power-domain-cells = <1>;
 			};
 
-			k2g_clks: clocks {
+			k2g_clks: clock-controller {
 				compatible = "ti,k2g-sci-clk";
 				#clock-cells = <2>;
 			};
@@ -324,9 +324,31 @@
 			clock-names = "gpio";
 		};
 
+		dss: dss@02540000 {
+			compatible = "ti,k2g-dss";
+			reg = <0x02540000 0x400>,
+				<0x02550000 0x1000>,
+				<0x02557000 0x1000>,
+				<0x0255a800 0x100>,
+				<0x0255ac00 0x100>;
+			reg-names = "cfg", "common", "vid1", "ovr1", "vp1";
+			clocks = <&k2g_clks 0x2 0>,
+					<&k2g_clks 0x2 1>;
+			clock-names = "fck", "vp1";
+			interrupts = <GIC_SPI 247 IRQ_TYPE_EDGE_RISING>;
+
+			power-domains = <&k2g_pds 0x2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			max-memory-bandwidth = <230000000>;
+		};
+
 		edma0: edma@2700000 {
 			compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
-			reg =	<0x02700000 0x8000>;
+			reg = <0x02700000 0x8000>;
 			reg-names = "edma3_cc";
 			interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>,
 					<GIC_SPI 216 IRQ_TYPE_EDGE_RISING>,
@@ -345,19 +367,19 @@
 
 		edma0_tptc0: tptc@2760000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x02760000 0x400>;
+			reg = <0x02760000 0x400>;
 			power-domains = <&k2g_pds 0x3f>;
 		};
 
 		edma0_tptc1: tptc@2768000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x02768000 0x400>;
+			reg = <0x02768000 0x400>;
 			power-domains = <&k2g_pds 0x3f>;
 		};
 
 		edma1: edma@2728000 {
 			compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
-			reg =	<0x02728000 0x8000>;
+			reg = <0x02728000 0x8000>;
 			reg-names = "edma3_cc";
 			interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
 					<GIC_SPI 219 IRQ_TYPE_EDGE_RISING>,
@@ -380,13 +402,13 @@
 
 		edma1_tptc0: tptc@27b0000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x027b0000 0x400>;
+			reg = <0x027b0000 0x400>;
 			power-domains = <&k2g_pds 0x4f>;
 		};
 
 		edma1_tptc1: tptc@27b8000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x027b8000 0x400>;
+			reg = <0x027b8000 0x400>;
 			power-domains = <&k2g_pds 0x4f>;
 		};
 
@@ -571,7 +593,7 @@
 
 		spi2: spi@21805c00 {
 			compatible = "ti,keystone-spi";
-			reg = <0x21805C00 0x200>;
+			reg = <0x21805c00 0x200>;
 			num-cs = <4>;
 			ti,davinci-spi-intr-line = <0>;
 			interrupts = <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>;
diff --git a/arch/arm/boot/dts/keystone-k2hk-clocks.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2hk-clocks.dtsi
index 4ba6912176ef..4ba6912176ef 100644
--- a/arch/arm/boot/dts/keystone-k2hk-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2hk-clocks.dtsi
diff --git a/arch/arm/boot/dts/keystone-k2hk-evm.dts b/arch/arm/boot/dts/ti/keystone/keystone-k2hk-evm.dts
index ad4e22afe133..8dfb54295027 100644
--- a/arch/arm/boot/dts/keystone-k2hk-evm.dts
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2hk-evm.dts
@@ -10,7 +10,7 @@
 #include "keystone-k2hk.dtsi"
 
 / {
-	compatible =  "ti,k2hk-evm", "ti,k2hk", "ti,keystone";
+	compatible = "ti,k2hk-evm", "ti,k2hk", "ti,keystone";
 	model = "Texas Instruments Keystone 2 Kepler/Hawking EVM";
 
 	reserved-memory {
@@ -28,22 +28,22 @@
 
 	leds {
 		compatible = "gpio-leds";
-		debug1_1 {
+		led-debug-1-1 {
 			label = "keystone:green:debug1";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* 12 */
 		};
 
-		debug1_2 {
+		led-debug-1-2 {
 			label = "keystone:red:debug1";
 			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; /* 13 */
 		};
 
-		debug2 {
+		led-debug-2 {
 			label = "keystone:blue:debug2";
 			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; /* 14 */
 		};
 
-		debug3 {
+		led-debug-3 {
 			label = "keystone:blue:debug3";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; /* 15 */
 		};
@@ -154,17 +154,17 @@
 };
 
 &i2c0 {
-	dtt@50 {
+	eeprom@50 {
 		compatible = "atmel,24c1024";
 		reg = <0x50>;
 	};
 };
 
 &spi0 {
-	nor_flash: n25q128a11@0 {
+	nor_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "Micron,n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <54000000>;
 		m25p,fast-read;
 		reg = <0>;
@@ -183,7 +183,7 @@
 };
 
 &mdio {
-	status = "ok";
+	status = "okay";
 	ethphy0: ethernet-phy@0 {
 		compatible = "marvell,88E1111", "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
diff --git a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2hk-netcp.dtsi
index d5a6c1f5633c..c2ee775eab6a 100644
--- a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2hk-netcp.dtsi
@@ -12,9 +12,9 @@ qmss: qmss@2a40000 {
 	#size-cells = <1>;
 	clocks = <&chipclk13>;
 	ranges;
-	queue-range	= <0 0x4000>;
-	linkram0	= <0x100000 0x8000>;
-	linkram1	= <0x0 0x10000>;
+	queue-range = <0 0x4000>;
+	linkram0 = <0x100000 0x8000>;
+	linkram1 = <0x0 0x10000>;
 
 	qmgrs {
 		#address-cells = <1>;
@@ -49,9 +49,9 @@ qmss: qmss@2a40000 {
 		qpend {
 			qpend-0 {
 				qrange = <658 8>;
-				interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04
-					     0 43 0xf04 0 44 0xf04 0 45 0xf04
-					     0 46 0xf04 0 47 0xf04>;
+				interrupts = <0 40 0xf04 0 41 0xf04 0 42 0xf04
+					      0 43 0xf04 0 44 0xf04 0 45 0xf04
+					      0 46 0xf04 0 47 0xf04>;
 			};
 			qpend-1 {
 				qrange = <8704 16>;
@@ -112,7 +112,7 @@ qmss: qmss@2a40000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
-		pdsp0@0x2a10000 {
+		pdsp0@2a10000 {
 			reg = <0x2a10000 0x1000    /*iram */
 			       0x2a0f000 0x100     /*reg*/
 			       0x2a0c000 0x3c8	   /*intd */
@@ -150,7 +150,7 @@ netcp: netcp@2000000 {
 	#size-cells = <1>;
 
 	/* NetCP address range */
-	ranges  = <0 0x2000000 0x100000>;
+	ranges = <0 0x2000000 0x100000>;
 
 	clocks = <&clkpa>, <&clkcpgmac>;
 	clock-names = "pa_clk", "ethss_clk";
@@ -207,11 +207,11 @@ netcp: netcp@2000000 {
 			secondary-slave-ports {
 				port-2 {
 					slave-port = <2>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-3 {
 					slave-port = <3>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2hk.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2hk.dtsi
index ca0f198ba627..da6d3934c2e8 100644
--- a/arch/arm/boot/dts/keystone-k2hk.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2hk.dtsi
@@ -57,14 +57,14 @@
 &soc0 {
 		/include/ "keystone-k2hk-clocks.dtsi"
 
-		msm_ram: msmram@c000000 {
+		msm_ram: sram@c000000 {
 			compatible = "mmio-sram";
 			reg = <0x0c000000 0x600000>;
 			ranges = <0x0 0x0c000000 0x600000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			sram-bm@5f0000 {
+			bm-sram@5f0000 {
 				reg = <0x5f0000 0x8000>;
 			};
 		};
@@ -282,14 +282,14 @@
 		};
 
 		mdio: mdio@2090300 {
-			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			compatible = "ti,keystone_mdio", "ti,davinci_mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x02090300 0x100>;
 			status = "disabled";
 			clocks = <&clkcpgmac>;
 			clock-names = "fck";
-			bus_freq	= <2500000>;
+			bus_freq = <2500000>;
 		};
 		/include/ "keystone-k2hk-netcp.dtsi"
 };
diff --git a/arch/arm/boot/dts/keystone-k2l-clocks.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2l-clocks.dtsi
index 635528064dea..635528064dea 100644
--- a/arch/arm/boot/dts/keystone-k2l-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2l-clocks.dtsi
diff --git a/arch/arm/boot/dts/keystone-k2l-evm.dts b/arch/arm/boot/dts/ti/keystone/keystone-k2l-evm.dts
index e200533d26a4..be619e39a16f 100644
--- a/arch/arm/boot/dts/keystone-k2l-evm.dts
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2l-evm.dts
@@ -51,7 +51,7 @@
 };
 
 &i2c0 {
-	dtt@50 {
+	eeprom@50 {
 		compatible = "atmel,24c1024";
 		reg = <0x50>;
 	};
@@ -103,17 +103,17 @@
 
 			partition@180000 {
 				label = "ubifs";
-				reg = <0x180000 0x7FE80000>;
+				reg = <0x180000 0x7fe80000>;
 			};
 		};
 	};
 };
 
 &spi0 {
-	nor_flash: n25q128a11@0 {
+	nor_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "Micron,n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <54000000>;
 		m25p,fast-read;
 		reg = <0>;
@@ -132,7 +132,7 @@
 };
 
 &mdio {
-	status = "ok";
+	status = "okay";
 	ethphy0: ethernet-phy@0 {
 		compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
diff --git a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2l-netcp.dtsi
index c1f982604145..1afebd7458c1 100644
--- a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2l-netcp.dtsi
@@ -12,9 +12,9 @@ qmss: qmss@2a40000 {
 	#size-cells = <1>;
 	clocks = <&chipclk13>;
 	ranges;
-	queue-range	= <0 0x2000>;
-	linkram0	= <0x100000 0x4000>;
-	linkram1	= <0x70000000 0x10000>; /* 1MB OSR mem */
+	queue-range = <0 0x2000>;
+	linkram0 = <0x100000 0x4000>;
+	linkram1 = <0x70000000 0x10000>; /* 1MB OSR mem */
 
 	qmgrs {
 		#address-cells = <1>;
@@ -36,9 +36,9 @@ qmss: qmss@2a40000 {
 		qpend {
 			qpend-0 {
 				qrange = <658 8>;
-				interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04
-					     0 43 0xf04 0 44 0xf04 0 45 0xf04
-					     0 46 0xf04 0 47 0xf04>;
+				interrupts = <0 40 0xf04 0 41 0xf04 0 42 0xf04
+					      0 43 0xf04 0 44 0xf04 0 45 0xf04
+					      0 46 0xf04 0 47 0xf04>;
 			};
 			qpend-1 {
 				qrange = <528 16>;
@@ -94,7 +94,7 @@ qmss: qmss@2a40000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
-		pdsp0@0x2a10000 {
+		pdsp0@2a10000 {
 			reg = <0x2a10000 0x1000    /*iram */
 			       0x2a0f000 0x100     /*reg*/
 			       0x2a0c000 0x3c8	   /*intd */
@@ -174,24 +174,24 @@ netcp: netcp@26000000 {
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy0>;
+					link-interface = <1>;
+					phy-handle = <&ethphy0>;
 				};
 				gbe1: interface-1 {
 					slave-port = <1>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy1>;
+					link-interface = <1>;
+					phy-handle = <&ethphy1>;
 				};
 			};
 
 			secondary-slave-ports {
 				port-2 {
 					slave-port = <2>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-3 {
 					slave-port = <3>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2l.dtsi b/arch/arm/boot/dts/ti/keystone/keystone-k2l.dtsi
index 374c80124c4e..2062fe561642 100644
--- a/arch/arm/boot/dts/keystone-k2l.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone-k2l.dtsi
@@ -47,7 +47,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02348400 0x100>;
-			clocks	= <&clkuart2>;
+			clocks = <&clkuart2>;
 			interrupts = <GIC_SPI 432 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -57,7 +57,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02348800 0x100>;
-			clocks	= <&clkuart3>;
+			clocks = <&clkuart3>;
 			interrupts = <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -116,42 +116,42 @@
 			pinctrl-single,function-mask = <0x1>;
 			status = "disabled";
 
-			uart3_emifa_pins: pinmux_uart3_emifa_pins {
+			uart3_emifa_pins: uart3-emifa-pins {
 				pinctrl-single,bits = <
 					/* UART3_EMIFA_SEL */
 					0x0 0x0  0xc0
 				>;
 			};
 
-			uart2_emifa_pins: pinmux_uart2_emifa_pins {
+			uart2_emifa_pins: uart2-emifa-pins {
 			pinctrl-single,bits = <
 					/* UART2_EMIFA_SEL */
 					0x0 0x0  0x30
 				>;
 			};
 
-			uart01_spi2_pins: pinmux_uart01_spi2_pins {
+			uart01_spi2_pins: uart01-spi2-pins {
 				pinctrl-single,bits = <
 					/* UART01_SPI2_SEL */
 					0x0 0x0 0x4
 				>;
 			};
 
-			dfesync_rp1_pins: pinmux_dfesync_rp1_pins{
+			dfesync_rp1_pins: dfesync-rp1-pins {
 				pinctrl-single,bits = <
 					/* DFESYNC_RP1_SEL */
 					0x0 0x0 0x2
 				>;
 			};
 
-			avsif_pins: pinmux_avsif_pins {
+			avsif_pins: avsif-pins {
 				pinctrl-single,bits = <
 					/* AVSIF_SEL */
 					0x0 0x0 0x1
 				>;
 			};
 
-			gpio_emu_pins: pinmux_gpio_emu_pins {
+			gpio_emu_pins: gpio-emu-pins {
 				pinctrl-single,bits = <
 				/*
 				 * GPIO_EMU_SEL[31]: 0-GPIO31, 1-EMU33
@@ -170,11 +170,11 @@
 				 * GPIO_EMU_SEL[18]: 0-GPIO18, 1-EMU20
 				 * GPIO_EMU_SEL[17]: 0-GPIO17, 1-EMU19
 				 */
-					0x4 0x0000 0xFFFE0000
+					0x4 0x0000 0xfffe0000
 				>;
 			};
 
-			gpio_timio_pins: pinmux_gpio_timio_pins {
+			gpio_timio_pins: gpio-timio-pins {
 				pinctrl-single,bits = <
 				/*
 				 * GPIO_TIMIO_SEL[15]: 0-GPIO15, 1-TIMO7
@@ -190,11 +190,11 @@
 				 * GPIO_TIMIO_SEL[5]: 0-GPIO5, 1-TIMI3
 				 * GPIO_TIMIO_SEL[4]: 0-GPIO4, 1-TIMI2
 				 */
-					0x4 0x0 0xFFF0
+					0x4 0x0 0xfff0
 				>;
 			};
 
-			gpio_spi2cs_pins: pinmux_gpio_spi2cs_pins {
+			gpio_spi2cs_pins: gpio-spi2cs-pins {
 				pinctrl-single,bits = <
 				/*
 				 * GPIO_SPI2CS_SEL[3]: 0-GPIO3, 1-SPI2CS4
@@ -202,11 +202,11 @@
 				 * GPIO_SPI2CS_SEL[1]: 0-GPIO1, 1-SPI2CS2
 				 * GPIO_SPI2CS_SEL[0]: 0-GPIO0, 1-SPI2CS1
 				 */
-					0x4 0x0 0xF
+					0x4 0x0 0xf
 				>;
 			};
 
-			gpio_dfeio_pins: pinmux_gpio_dfeio_pins {
+			gpio_dfeio_pins: gpio-dfeio-pins {
 				pinctrl-single,bits = <
 				/*
 				 * GPIO_DFEIO_SEL[31]: 0-DFEIO17, 1-GPIO63
@@ -226,11 +226,11 @@
 				 * GPIO_DFEIO_SEL[17]: 0-DFEIO3, 1-GPIO49
 				 * GPIO_DFEIO_SEL[16]: 0-DFEIO2, 1-GPIO48
 				 */
-					0x8 0x0 0xFFFF0000
+					0x8 0x0 0xffff0000
 				>;
 			};
 
-			gpio_emifa_pins: pinmux_gpio_emifa_pins {
+			gpio_emifa_pins: gpio-emifa-pins {
 				pinctrl-single,bits = <
 				/*
 				 * GPIO_EMIFA_SEL[15]: 0-EMIFA17, 1-GPIO47
@@ -250,19 +250,19 @@
 				 * GPIO_EMIFA_SEL[1]: 0-EMIFA1, 1-GPIO33
 				 * GPIO_EMIFA_SEL[0]: 0-EMIFA0, 1-GPIO32
 				 */
-					0x8 0x0 0xFFFF
+					0x8 0x0 0xffff
 				>;
 			};
 		};
 
-		msm_ram: msmram@c000000 {
+		msm_ram: sram@c000000 {
 			compatible = "mmio-sram";
 			reg = <0x0c000000 0x200000>;
 			ranges = <0x0 0x0c000000 0x200000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			sram-bm@1f8000 {
+			bm-sram@1f8000 {
 				reg = <0x001f8000 0x8000>;
 			};
 		};
@@ -388,14 +388,14 @@
 		};
 
 		mdio: mdio@26200f00 {
-			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			compatible = "ti,keystone_mdio", "ti,davinci_mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x26200f00 0x100>;
 			status = "disabled";
 			clocks = <&clkcpgmac>;
 			clock-names = "fck";
-			bus_freq	= <2500000>;
+			bus_freq = <2500000>;
 		};
 		/include/ "keystone-k2l-netcp.dtsi"
 };
diff --git a/arch/arm/boot/dts/keystone.dtsi b/arch/arm/boot/dts/ti/keystone/keystone.dtsi
index c298675a29a5..1fd04bb37a15 100644
--- a/arch/arm/boot/dts/keystone.dtsi
+++ b/arch/arm/boot/dts/ti/keystone/keystone.dtsi
@@ -14,7 +14,7 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
-		serial0	= &uart0;
+		serial0 = &uart0;
 		spi0 = &spi0;
 		spi1 = &spi1;
 		spi2 = &spi2;
@@ -61,17 +61,17 @@
 	};
 
 	psci {
-		compatible	= "arm,psci";
-		method		= "smc";
-		cpu_suspend	= <0x84000001>;
-		cpu_off		= <0x84000002>;
-		cpu_on		= <0x84000003>;
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend = <0x84000001>;
+		cpu_off = <0x84000002>;
+		cpu_on = <0x84000003>;
 	};
 
 	soc0: soc@0 {
+		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "ti,keystone","simple-bus";
 		interrupt-parent = <&gic>;
 		ranges = <0x0 0x0 0x0 0xc0000000>;
 		dma-ranges = <0x80000000 0x8 0x00000000 0x80000000>;
@@ -119,7 +119,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02530c00 0x100>;
-			clocks	= <&clkuart0>;
+			clocks = <&clkuart0>;
 			interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -129,7 +129,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02531000 0x100>;
-			clocks	= <&clkuart1>;
+			clocks = <&clkuart1>;
 			interrupts = <GIC_SPI 280 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -217,8 +217,8 @@
 			dma-ranges;
 			status = "disabled";
 
-			usb0: dwc3@2690000 {
-				compatible = "synopsys,dwc3";
+			usb0: usb@2690000 {
+				compatible = "snps,dwc3";
 				reg = <0x2690000 0x70000>;
 				interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>;
 				usb-phy = <&usb_phy>, <&usb_phy>;
@@ -282,7 +282,7 @@
 			ti,davinci-gpio-unbanked = <32>;
 		};
 
-		aemif: aemif@21000A00 {
+		aemif: aemif@21000a00 {
 			compatible = "ti,keystone-aemif", "ti,davinci-aemif";
 			#address-cells = <2>;
 			#size-cells = <1>;
@@ -290,9 +290,9 @@
 			clock-names = "aemif";
 			clock-ranges;
 
-			reg = <0x21000A00 0x00000100>;
+			reg = <0x21000a00 0x00000100>;
 			ranges = <0 0 0x30000000 0x10000000
-				  1 0 0x21000A00 0x00000100>;
+				  1 0 0x21000a00 0x00000100>;
 		};
 
 		pcie0: pcie@21800000 {
@@ -301,7 +301,7 @@
 			clock-names = "pcie";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			reg =  <0x21801000 0x2000>, <0x21800000 0x1000>, <0x02620128 4>;
+			reg = <0x21801000 0x2000>, <0x21800000 0x1000>, <0x02620128 4>;
 			ranges = <0x82000000 0 0x50000000 0x50000000
 				  0 0x10000000>;
 
diff --git a/arch/arm/boot/dts/ti/omap/Makefile b/arch/arm/boot/dts/ti/omap/Makefile
new file mode 100644
index 000000000000..95c68135dd0c
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/Makefile
@@ -0,0 +1,175 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_OMAP2) += \
+	omap2420-h4.dtb \
+	omap2420-n800.dtb \
+	omap2420-n810.dtb \
+	omap2420-n810-wimax.dtb \
+	omap2430-sdp.dtb
+dtb-$(CONFIG_ARCH_OMAP3) += \
+	am3517-craneboard.dtb \
+	am3517-evm.dtb \
+	am3517_mt_ventoux.dtb \
+	logicpd-torpedo-35xx-devkit.dtb \
+	logicpd-torpedo-37xx-devkit.dtb \
+	logicpd-torpedo-37xx-devkit-28.dtb \
+	logicpd-som-lv-35xx-devkit.dtb \
+	logicpd-som-lv-37xx-devkit.dtb \
+	omap3430-sdp.dtb \
+	omap3-beagle.dtb \
+	omap3-beagle-ab4.dtb \
+	omap3-beagle-xm.dtb \
+	omap3-beagle-xm-ab.dtb \
+	omap3-cm-t3517.dtb \
+	omap3-cm-t3530.dtb \
+	omap3-cm-t3730.dtb \
+	omap3-devkit8000.dtb \
+	omap3-devkit8000-lcd43.dtb \
+	omap3-devkit8000-lcd70.dtb \
+	omap3-echo.dtb \
+	omap3-evm.dtb \
+	omap3-evm-37xx.dtb \
+	omap3-gta04a3.dtb \
+	omap3-gta04a4.dtb \
+	omap3-gta04a5.dtb \
+	omap3-gta04a5one.dtb \
+	omap3-ha.dtb \
+	omap3-ha-lcd.dtb \
+	omap3-igep0020.dtb \
+	omap3-igep0020-rev-f.dtb \
+	omap3-igep0030.dtb \
+	omap3-igep0030-rev-g.dtb \
+	omap3-ldp.dtb \
+	omap3-lilly-dbb056.dtb \
+	omap3-n900.dtb \
+	omap3-n9.dtb \
+	omap3-n950.dtb \
+	omap3-overo-alto35.dtb \
+	omap3-overo-chestnut43.dtb \
+	omap3-overo-gallop43.dtb \
+	omap3-overo-palo35.dtb \
+	omap3-overo-palo43.dtb \
+	omap3-overo-storm-alto35.dtb \
+	omap3-overo-storm-chestnut43.dtb \
+	omap3-overo-storm-gallop43.dtb \
+	omap3-overo-storm-palo35.dtb \
+	omap3-overo-storm-palo43.dtb \
+	omap3-overo-storm-summit.dtb \
+	omap3-overo-storm-tobi.dtb \
+	omap3-overo-storm-tobiduo.dtb \
+	omap3-overo-summit.dtb \
+	omap3-overo-tobi.dtb \
+	omap3-overo-tobiduo.dtb \
+	omap3-pandora-600mhz.dtb \
+	omap3-pandora-1ghz.dtb \
+	omap3-sbc-t3517.dtb \
+	omap3-sbc-t3530.dtb \
+	omap3-sbc-t3730.dtb \
+	omap3-sniper.dtb \
+	omap3-thunder.dtb \
+	omap3-zoom3.dtb
+dtb-$(CONFIG_ARCH_OMAP4) += \
+	omap4-droid-bionic-xt875.dtb \
+	omap4-droid4-xt894.dtb \
+	omap4-duovero-parlor.dtb \
+	omap4-epson-embt2ws.dtb \
+	omap4-kc1.dtb \
+	omap4-panda.dtb \
+	omap4-panda-a4.dtb \
+	omap4-panda-es.dtb \
+	omap4-sdp.dtb \
+	omap4-sdp-es23plus.dtb \
+	omap4-var-dvk-om44.dtb \
+	omap4-var-stk-om44.dtb \
+	omap4-xyboard-mz609.dtb \
+	omap4-xyboard-mz617.dtb
+dtb-$(CONFIG_SOC_AM33XX) += \
+	am335x-baltos-ir2110.dtb \
+	am335x-baltos-ir3220.dtb \
+	am335x-baltos-ir5221.dtb \
+	am335x-base0033.dtb \
+	am335x-bone.dtb \
+	am335x-boneblack.dtb \
+	am335x-boneblack-wireless.dtb \
+	am335x-boneblue.dtb \
+	am335x-bonegreen.dtb \
+	am335x-bonegreen-wireless.dtb \
+	am335x-chiliboard.dtb \
+	am335x-cm-t335.dtb \
+	am335x-evm.dtb \
+	am335x-evmsk.dtb \
+	am335x-guardian.dtb \
+	am335x-icev2.dtb \
+	am335x-lxm.dtb \
+	am335x-moxa-uc-2101.dtb \
+	am335x-moxa-uc-8100-me-t.dtb \
+	am335x-myirtech-myd.dtb \
+	am335x-nano.dtb \
+	am335x-netcan-plus-1xx.dtb \
+	am335x-netcom-plus-2xx.dtb \
+	am335x-netcom-plus-8xx.dtb \
+	am335x-pdu001.dtb \
+	am335x-pepper.dtb \
+	am335x-phycore-rdk.dtb \
+	am335x-pocketbeagle.dtb \
+	am335x-regor-rdk.dtb \
+	am335x-sancloud-bbe.dtb \
+	am335x-sancloud-bbe-lite.dtb \
+	am335x-sancloud-bbe-extended-wifi.dtb \
+	am335x-shc.dtb \
+	am335x-sbc-t335.dtb \
+	am335x-sl50.dtb \
+	am335x-wega-rdk.dtb \
+	am335x-osd3358-sm-red.dtb
+dtb-$(CONFIG_SOC_AM43XX) += \
+	am43x-epos-evm.dtb \
+	am437x-cm-t43.dtb \
+	am437x-gp-evm.dtb \
+	am437x-idk-evm.dtb \
+	am437x-sbc-t43.dtb \
+	am437x-sk-evm.dtb
+
+am57xx-evm-dtbs := am57xx-beagle-x15.dtb am57xx-evm.dtbo
+am57xx-evm-reva3-dtbs := am57xx-beagle-x15-revc.dtb am57xx-evm.dtbo
+
+am571x-idk-overlays-dtbs := am571x-idk.dtb \
+	am571x-idk-touchscreen.dtbo am57xx-idk-lcd-osd101t2587.dtbo
+am572x-idk-overlays-dtbs := am572x-idk.dtb \
+	am572x-idk-touchscreen.dtbo am57xx-idk-lcd-osd101t2045.dtbo
+
+# Build time test only, enabled by CONFIG_OF_ALL_DTBS
+dtb- += \
+	am571x-idk-overlays.dtb \
+	am572x-idk-overlays.dtb
+
+dtb-$(CONFIG_SOC_DRA7XX) += \
+	am57xx-beagle-x15.dtb \
+	am57xx-beagle-x15-revb1.dtb \
+	am57xx-beagle-x15-revc.dtb \
+	am57xx-evm.dtb \
+	am57xx-evm-reva3.dtb \
+	am5729-beagleboneai.dtb \
+	am57xx-cl-som-am57x.dtb \
+	am57xx-sbc-am57x.dtb \
+	am572x-idk.dtb \
+	am572x-idk-touchscreen.dtbo \
+	am571x-idk.dtb \
+	am571x-idk-touchscreen.dtbo \
+	am574x-idk.dtb \
+	am57xx-idk-lcd-osd101t2045.dtbo \
+	am57xx-idk-lcd-osd101t2587.dtbo \
+	dra7-evm.dtb \
+	dra72-evm.dtb \
+	dra72-evm-revc.dtb \
+	dra71-evm.dtb \
+	dra76-evm.dtb
+dtb-$(CONFIG_SOC_OMAP5) += \
+	omap5-cm-t54.dtb \
+	omap5-igep0050.dtb \
+	omap5-sbc-t54.dtb \
+	omap5-uevm.dtb
+dtb-$(CONFIG_SOC_TI81XX) += \
+	am3874-iceboard.dtb \
+	dm8148-evm.dtb \
+	dm8148-t410.dtb \
+	dm8168-evm.dtb \
+	dra62x-j5eco-evm.dtb
diff --git a/arch/arm/boot/dts/ti/omap/am335x-baltos-ir2110.dts b/arch/arm/boot/dts/ti/omap/am335x-baltos-ir2110.dts
new file mode 100644
index 000000000000..ea5882ed7010
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-baltos-ir2110.dts
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/*
+ * VScom OnRISC
+ * http://www.vscom.de
+ */
+
+/dts-v1/;
+
+#include "am335x-baltos.dtsi"
+#include "am335x-baltos-leds.dtsi"
+
+/ {
+	model = "OnRISC Baltos iR 2110";
+};
+
+&am33xx_pinmux {
+	uart1_pins: uart1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE7)      /* lcd_vsync.gpio2[22] DTR */
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)      /* lcd_hsync.gpio2[23] DSR */
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)      /* lcd_pclk.gpio2[24] DCD */
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)      /* lcd_ac_bias_en.gpio2[25] RI */
+		>;
+	};
+
+	mmc1_pins: mmc1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT, MUX_MODE7)     /* MMC1 CD */
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&davinci_mdio_sw {
+	phy0: ethernet-phy@0 {
+		reg = <1>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rmii";
+	ti,dual-emac-pvid = <1>;
+	phy-handle = <&phy0>;
+};
+
+&cpsw_port2 {
+	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <2>;
+	phy-handle = <&phy1>;
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+};
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"NC",
+		"NC",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"RMII1_TXD1",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"RMII1_TXD0",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"NC",
+		"NC",
+		"NC",
+		"SD_CD",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"RMII1_RXD1",
+		"RMII1_RXD0",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"RMII1_CRS_DV",
+		"RMII1_RXER",
+		"RMII1_TXEN",
+		"NC",
+		"NC",
+		"NC",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"ModeA0",
+		"ModeA1",
+		"ModeA2",
+		"ModeA3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-baltos-ir3220.dts b/arch/arm/boot/dts/ti/omap/am335x-baltos-ir3220.dts
index b0df7256db13..ea4f8dde6424 100644
--- a/arch/arm/boot/dts/am335x-baltos-ir3220.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-baltos-ir3220.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -18,13 +18,13 @@
 };
 
 &am33xx_pinmux {
-	tca6416_pins: pinmux_tca6416_pins {
+	tca6416_pins: tca6416-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE7)      /* xdma_event_intr1.gpio0[20] tca6416 stuff */
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)
@@ -37,7 +37,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE1)      /* spi0_sclk.uart2_rxd_mux3 */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE1)      /* spi0_d0.uart2_txd_mux3 */
@@ -52,7 +52,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT, MUX_MODE7)     /* MMC1 CD */
 		>;
@@ -91,6 +91,10 @@
 		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tca6416_pins>;
+		gpio-line-names = "GP_IN0", "GP_IN1", "GP_IN2", "GP_IN3",
+				  "GP_OUT0", "GP_OUT1", "GP_OUT2", "GP_OUT3",
+				  "ModeA0", "ModeA1", "ModeA2", "ModeA3",
+				  "ModeB0", "ModeB1", "ModeB2", "ModeB3";
 	};
 };
 
@@ -103,18 +107,18 @@
 	dr_mode = "host";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	fixed-link {
 		speed = <100>;
 		full-duplex;
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
 
@@ -123,3 +127,147 @@
 	pinctrl-0 = <&mmc1_pins>;
 	cd-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"UART2_RX",
+		"UART2_TX",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"WLAN_BTN",
+		"W_DISABLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"TCA6416_INT",
+		"RMII1_TXD1",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"RMII1_TXD0",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"UART2_DTR",
+		"UART2_DSR",
+		"UART2_DCD",
+		"UART2_RI",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SD_CD",
+		"SD_WP",
+		"RMII1_RXD1",
+		"RMII1_RXD0",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"RMII1_CRS_DV",
+		"RMII1_RXER",
+		"RMII1_TXEN",
+		"3G_PWR_EN",
+		"UART2_CTSN",
+		"UART2_RTSN",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"USB1_DRVVBUS",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/ti/omap/am335x-baltos-ir5221.dts
index d6aa46e8700e..ec914f27d11d 100644
--- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-baltos-ir5221.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -18,21 +18,21 @@
 };
 
 &am33xx_pinmux {
-	tca6416_pins: pinmux_tca6416_pins {
+	tca6416_pins: tca6416-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE7)      /* xdma_event_intr1.gpio0[20] tca6416 stuff */
 		>;
 	};
 
 
-	dcan1_pins: pinmux_dcan1_pins {
+	dcan1_pins: dcan1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)      /* uart0_ctsn.dcan1_tx_mux0 */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)      /* uart0_rtsn.dcan1_rx_mux0 */
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)
@@ -45,7 +45,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE1)      /* spi0_sclk.uart2_rxd_mux3 */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE1)      /* spi0_d0.uart2_txd_mux3 */
@@ -60,7 +60,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT, MUX_MODE7)     /* MMC1 CD */
 		>;
@@ -99,6 +99,10 @@
 		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tca6416_pins>;
+		gpio-line-names = "GP_IN0", "GP_IN1", "GP_IN2", "GP_IN3",
+				  "GP_OUT0", "GP_OUT1", "GP_OUT2", "GP_OUT3",
+				  "ModeA0", "ModeA1", "ModeA2", "ModeA3",
+				  "ModeB0", "ModeB1", "ModeB2", "ModeB3";
 	};
 };
 
@@ -120,18 +124,18 @@
 	dr_mode = "host";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	fixed-link {
 		speed = <100>;
 		full-duplex;
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
 
@@ -147,3 +151,147 @@
 	pinctrl-0 = <&mmc1_pins>;
 	cd-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"UART2_RX",
+		"UART2_TX",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"WLAN_BTN",
+		"W_DISABLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"TCA6416_INT",
+		"RMII1_TXD1",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"RMII1_TXD0",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"DCAN1_TX",
+		"DCAN1_RX",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"UART2_DTR",
+		"UART2_DSR",
+		"UART2_DCD",
+		"UART2_RI",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SD_CD",
+		"SD_WP",
+		"RMII1_RXD1",
+		"RMII1_RXD0",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"RMII1_CRS_DV",
+		"RMII1_RXER",
+		"RMII1_TXEN",
+		"3G_PWR_EN",
+		"UART2_CTSN",
+		"UART2_RTSN",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"USB1_DRVVBUS",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-baltos-leds.dtsi b/arch/arm/boot/dts/ti/omap/am335x-baltos-leds.dtsi
index 4e11a160d88f..6a52e42b9e81 100644
--- a/arch/arm/boot/dts/am335x-baltos-leds.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-baltos-leds.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -17,18 +17,18 @@
 
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "onrisc:red:power";
 			linux,default-trigger = "default-on";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
-		wlan {
+		led-wlan {
 			label = "onrisc:blue:wlan";
 			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
-		app {
+		led-app {
 			label = "onrisc:green:app";
 			gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -37,7 +37,7 @@
 };
 
 &am33xx_pinmux {
-	user_leds: pinmux_user_leds {
+	user_leds: user-leds-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* mii1_col.gpio3_0 PWR LED */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* mii1_txd3.gpio0_16 WLAN LED */
diff --git a/arch/arm/boot/dts/am335x-baltos.dtsi b/arch/arm/boot/dts/ti/omap/am335x-baltos.dtsi
index 05e7b5d4a95b..c14d5b70c72f 100644
--- a/arch/arm/boot/dts/am335x-baltos.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-baltos.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -48,7 +48,7 @@
 };
 
 &am33xx_pinmux {
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_INPUT_PULLUP, MUX_MODE2)      /* gpmc_ad8.mmc1_dat0_mux0 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT_PULLUP, MUX_MODE2)      /* gpmc_ad9.mmc1_dat1_mux0 */
@@ -60,33 +60,33 @@
 		>;
 	};
 
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_EMU1, PIN_OUTPUT_PULLUP, MUX_MODE7)      /* emu1.gpio3[8] */
 		>;
 	};
 
-	tps65910_pins: pinmux_tps65910_pins {
+	tps65910_pins: tps65910-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_INPUT_PULLUP, MUX_MODE7)      /* gpmc_ben1.gpio1[28] */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT, MUX_MODE2)      /* spi0_d1.i2c1_sda_mux3 */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT, MUX_MODE2)      /* spi0_cs0.i2c1_scl_mux3 */
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE1)       /* mii1_crs.rmii1_crs_dv */
@@ -114,7 +114,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -141,7 +141,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)	/* mdio_data.mdio_data */
@@ -149,7 +149,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -157,7 +157,7 @@
 		>;
 	};
 
-	nandflash_pins_s0: nandflash_pins_s0 {
+	nandflash_pins_s0: nandflash-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
@@ -168,7 +168,7 @@
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
-			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_31 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_OUTPUT, MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
@@ -197,7 +197,7 @@
 		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		ti,nand-xfer-type = "polled";
+		ti,nand-xfer-type = "prefetch-dma";
 
 		gpmc,device-nand = "true";
 		gpmc,device-width = <1>;
@@ -258,7 +258,7 @@
 	};
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vbat>;
@@ -285,7 +285,7 @@
 			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1312500>;
+			regulator-max-microvolt = <1351500>;
 			regulator-boot-on;
 			regulator-always-on;
 		};
@@ -339,16 +339,15 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	status = "okay";
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
@@ -369,7 +368,7 @@
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&wl12xx_vmmc>;
-	ti,non-removable;
+	non-removable;
 	bus-width = <4>;
 	cap-power-off-card;
 	pinctrl-names = "default";
@@ -393,10 +392,10 @@
 	status = "okay";
 };
 
-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };
 
-&gpio3 {
+&gpio3_target {
 	ti,no-reset-on-init;
 };
diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/ti/omap/am335x-base0033.dts
index 89c00ce42c26..eba843e22ea1 100644
--- a/arch/arm/boot/dts/am335x-base0033.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-base0033.dts
@@ -41,7 +41,7 @@
 };
 
 &am33xx_pinmux {
-	nxp_hdmi_pins: pinmux_nxp_hdmi_pins {
+	nxp_hdmi_pins: nxp-hdmi-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT, MUX_MODE3)	/* xdma_event_intr0.clkout1 */
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
@@ -66,13 +66,13 @@
 			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT, MUX_MODE0)
 		>;
 	};
-	nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins {
+	nxp_hdmi_off_pins: nxp-hdmi-off-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT, MUX_MODE3)	/* xdma_event_intr0.clkout1 */
 		>;
 	};
 
-	leds_base_pins: pinmux_leds_base_pins {
+	leds_base_pins: leds-base-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/ti/omap/am335x-bone-common.dtsi
index 6c9187bc0f17..96451c8a815c 100644
--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-bone-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 / {
@@ -66,7 +66,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&clkout2_pin>;
 
-	user_leds_s0: user_leds_s0 {
+	user_leds_s0: user-leds-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_a6.gpio1_22 */
@@ -75,34 +75,34 @@
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)	/* i2c0_sda.i2c0_sda */
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	clkout2_pin: pinmux_clkout2_pin {
+	clkout2_pin: clkout2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3)	/* xdma_event_intr1.clkout2 */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -121,7 +121,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -140,23 +140,27 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
+			/* Added to support GPIO controlled PHY reset */
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT_PULLUP, MUX_MODE7)
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			/* Added to support GPIO controlled PHY reset */
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7)		/* spio0_cs1.gpio0_6 */
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -168,7 +172,7 @@
 		>;
 	};
 
-	emmc_pins: pinmux_emmc_pins {
+	emmc_pins: emmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
@@ -215,6 +219,7 @@
 	baseboard_eeprom: baseboard_eeprom@50 {
 		compatible = "atmel,24c256";
 		reg = <0x50>;
+		vcc-supply = <&ldo4_reg>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -273,7 +278,7 @@
 };
 
 
-/include/ "tps65217.dtsi"
+/include/ "../../tps65217.dtsi"
 
 &tps {
 	/*
@@ -353,27 +358,34 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "mii";
+	ti,dual-emac-pvid = <1>;
 };
 
-&mac {
-	slaves = <1>;
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
+		/* Support GPIO reset on revision C3 boards */
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <300>;
+		reset-deassert-us = <6500>;
 	};
 };
 
@@ -396,4 +408,13 @@
 &rtc {
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
+	system-power-controller;
+};
+
+&pruss_tm {
+	status = "okay";
+};
+
+&wkup_m3_ipc {
+	firmware-name = "am335x-bone-scale-data.bin";
 };
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/ti/omap/am335x-bone.dts
index 43bfbce41049..b5d85ef51a02 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-bone.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/ti/omap/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/ti/omap/am335x-boneblack-common.dtsi
new file mode 100644
index 000000000000..a7a8c61ef9b2
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-boneblack-common.dtsi
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+	non-removable;
+};
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/ti/omap/am335x-boneblack-hdmi.dtsi
index 7ad079861efd..109f08fd174d 100644
--- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-boneblack-hdmi.dtsi
@@ -1,31 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/display/tda998x.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-&ldo3_reg {
-	regulator-min-microvolt = <1800000>;
-	regulator-max-microvolt = <1800000>;
-	regulator-always-on;
-};
-
-&mmc1 {
-	vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_pins>;
-	bus-width = <8>;
-	status = "okay";
-};
-
 &am33xx_pinmux {
-	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+	nxp_hdmi_bonelt_pins: nxp-hdmi-bonelt-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
@@ -51,13 +33,13 @@
 		>;
 	};
 
-	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+	nxp_hdmi_bonelt_off_pins: nxp-hdmi-bonelt-off-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
 		>;
 	};
 
-	mcasp0_pins: mcasp0_pins {
+	mcasp0_pins: mcasp0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
@@ -103,8 +85,13 @@
 		audio-ports = <	TDA998x_I2S	0x03>;
 
 		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
 			port@0 {
-				hdmi_0: endpoint@0 {
+				reg = <0>;
+
+				hdmi_0: endpoint {
 					remote-endpoint = <&lcdc_0>;
 				};
 			};
@@ -112,10 +99,6 @@
 	};
 };
 
-&rtc {
-	system-power-controller;
-};
-
 &mcasp0	{
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/ti/omap/am335x-boneblack-wireless.dts
index 3124d94c0b3c..b4b4b80df08c 100644
--- a/arch/arm/boot/dts/am335x-boneblack-wireless.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-boneblack-wireless.dts
@@ -1,12 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
@@ -18,7 +19,7 @@
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
-		startup-delay-us= <70000>;
+		startup-delay-us = <70000>;
 
 		/* WL_EN */
 		gpio = <&gpio3 9 0>;
@@ -27,13 +28,13 @@
 };
 
 &am33xx_pinmux {
-	bt_pins: pinmux_bt_pins {
+	bt_pins: bt-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gmii1_txd0.gpio0_28 - BT_EN */
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLUP, MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
@@ -44,7 +45,7 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* gmii1_rxd3.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* gmii1_rxd2.uart3_txd */
@@ -53,7 +54,7 @@
 		>;
 	};
 
-	wl18xx_pins: pinmux_wl18xx_pins {
+	wl18xx_pins: wl18xx-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gmii1_txclk.gpio3_9 WL_EN */
 			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* rmii1_refclk.gpio0_29 WL_IRQ */
@@ -62,7 +63,7 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "disabled";
 };
 
@@ -75,7 +76,6 @@
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	ti,needs-special-hs-handling;
 	keep-power-in-suspend;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
@@ -102,7 +102,7 @@
 };
 
 &gpio3 {
-	ls_buf_en {
+	ls-buf-en-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/ti/omap/am335x-boneblack.dts b/arch/arm/boot/dts/ti/omap/am335x-boneblack.dts
new file mode 100644
index 000000000000..16b567e3cb47
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-boneblack.dts
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
+
+/ {
+	model = "TI AM335x BeagleBone Black";
+	compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+};
+
+&cpu0_opp_table {
+	/*
+	 * All PG 2.0 silicon may not support 1GHz but some of the early
+	 * BeagleBone Blacks have PG 2.0 silicon which is guaranteed
+	 * to support 1GHz OPP so enable it for PG 2.0 on this board.
+	 */
+	opp-1000000000 {
+		/* OPP Nitro */
+		opp-supported-hw = <0x06 0x0100>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+		"[mdio_data]",
+		"[mdio_clk]",
+		"P9_22 [spi0_sclk]",
+		"P9_21 [spi0_d0]",
+		"P9_18 [spi0_d1]",
+		"P9_17 [spi0_cs0]",
+		"[mmc0_cd]",
+		"P8_42A [ecappwm0]",
+		"P8_35 [lcd d12]",
+		"P8_33 [lcd d13]",
+		"P8_31 [lcd d14]",
+		"P8_32 [lcd d15]",
+		"P9_20 [i2c2_sda]",
+		"P9_19 [i2c2_scl]",
+		"P9_26 [uart1_rxd]",
+		"P9_24 [uart1_txd]",
+		"[rmii1_txd3]",
+		"[rmii1_txd2]",
+		"[usb0_drvvbus]",
+		"[hdmi cec]",
+		"P9_41B",
+		"[rmii1_txd1]",
+		"P8_19 [ehrpwm2a]",
+		"P8_13 [ehrpwm2b]",
+		"NC",
+		"NC",
+		"P8_14",
+		"P8_17",
+		"[rmii1_txd0]",
+		"[rmii1_refclk]",
+		"P9_11 [uart4_rxd]",
+		"P9_13 [uart4_txd]";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"P8_25 [mmc1_dat0]",
+		"[mmc1_dat1]",
+		"P8_5 [mmc1_dat2]",
+		"P8_6 [mmc1_dat3]",
+		"P8_23 [mmc1_dat4]",
+		"P8_22 [mmc1_dat5]",
+		"P8_3 [mmc1_dat6]",
+		"P8_4 [mmc1_dat7]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"P8_12",
+		"P8_11",
+		"P8_16",
+		"P8_15",
+		"P9_15A",
+		"P9_23",
+		"P9_14 [ehrpwm1a]",
+		"P9_16 [ehrpwm1b]",
+		"[emmc rst]",
+		"[usr0 led]",
+		"[usr1 led]",
+		"[usr2 led]",
+		"[usr3 led]",
+		"[hdmi irq]",
+		"[usb vbus oc]",
+		"[hdmi audio]",
+		"P9_12",
+		"P8_26",
+		"P8_21 [emmc]",
+		"P8_20 [emmc]";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"P9_15B",
+		"P8_18",
+		"P8_7",
+		"P8_8",
+		"P8_10",
+		"P8_9",
+		"P8_45 [hdmi]",
+		"P8_46 [hdmi]",
+		"P8_43 [hdmi]",
+		"P8_44 [hdmi]",
+		"P8_41 [hdmi]",
+		"P8_42 [hdmi]",
+		"P8_39 [hdmi]",
+		"P8_40 [hdmi]",
+		"P8_37 [hdmi]",
+		"P8_38 [hdmi]",
+		"P8_36 [hdmi]",
+		"P8_34 [hdmi]",
+		"[rmii1_rxd3]",
+		"[rmii1_rxd2]",
+		"[rmii1_rxd1]",
+		"[rmii1_rxd0]",
+		"P8_27 [hdmi]",
+		"P8_29 [hdmi]",
+		"P8_28 [hdmi]",
+		"P8_30 [hdmi]",
+		"[mmc0_dat3]",
+		"[mmc0_dat2]",
+		"[mmc0_dat1]",
+		"[mmc0_dat0]",
+		"[mmc0_clk]",
+		"[mmc0_cmd]";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"[mii col]",
+		"[mii crs]",
+		"[mii rx err]",
+		"[mii tx en]",
+		"[mii rx dv]",
+		"[i2c0 sda]",
+		"[i2c0 scl]",
+		"[jtag emu0]",
+		"[jtag emu1]",
+		"[mii tx clk]",
+		"[mii rx clk]",
+		"NC",
+		"NC",
+		"[usb vbus en]",
+		"P9_31 [spi1_sclk]",
+		"P9_29 [spi1_d0]",
+		"P9_30 [spi1_d1]",
+		"P9_28 [spi1_cs0]",
+		"P9_42B [ecappwm0]",
+		"P9_27",
+		"P9_41A",
+		"P9_25",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
+
+&baseboard_eeprom {
+	vcc-supply = <&ldo4_reg>;
+};
diff --git a/arch/arm/boot/dts/am335x-boneblue.dts b/arch/arm/boot/dts/ti/omap/am335x-boneblue.dts
index 5811fb8d4fdf..801399702547 100644
--- a/arch/arm/boot/dts/am335x-boneblue.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-boneblue.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -106,7 +106,7 @@
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
-		startup-delay-us= <70000>;
+		startup-delay-us = <70000>;
 
 		/* WL_EN */
 		gpio = <&gpio3 9 0>;
@@ -115,7 +115,7 @@
 };
 
 &am33xx_pinmux {
-	user_leds_s0: user_leds_s0 {
+	user_leds_s0: user-leds-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7) /* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT, MUX_MODE7) /* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */
@@ -132,7 +132,7 @@
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* (D18) uart1_ctsn.I2C2_SDA */
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* (D17) uart1_rtsn.I2C2_SCL */
@@ -140,7 +140,7 @@
 	};
 
 	/* UT0 */
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -148,7 +148,7 @@
 	};
 
 	/* UT1 */
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -156,7 +156,7 @@
 	};
 
 	/* GPS */
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE1)	/* (A17) spi0_sclk.uart2_rxd */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* (B17) spi0_d0.uart2_txd */
@@ -164,27 +164,27 @@
 	};
 
 	/* DSM2 */
-	uart4_pins: pinmux_uart4_pins {
+	uart4_pins: uart4-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)	/* (T17) gpmc_wait0.uart4_rxd */
 		>;
 	};
 
 	/* UT5 */
-	uart5_pins: pinmux_uart5_pins {
+	uart5_pins: uart5-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_INPUT_PULLUP, MUX_MODE4)	/* (U2) lcd_data9.uart5_rxd */
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT_PULLDOWN, MUX_MODE4)	/* (U1) lcd_data8.uart5_txd */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7)		/* (C15) spi0_cs1.gpio0[6] */
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2)	/* (U9) gpmc_csn1.mmc1_clk */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2)	/* (V9) gpmc_csn2.mmc1_cmd */
@@ -199,7 +199,7 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE6)	/* (L15) gmii1_rxd1.mmc2_clk */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLUP, MUX_MODE6)	/* (J16) gmii1_txen.mmc2_cmd */
@@ -210,13 +210,13 @@
 		>;
 	};
 
-	bt_pins: pinmux_bt_pins {
+	bt_pins: bt-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* (K17) gmii1_txd0.gpio0[28] - BT_EN */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* (L17) gmii1_rxd3.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* (L16) gmii1_rxd2.uart3_txd */
@@ -225,7 +225,7 @@
 		>;
 	};
 
-	wl18xx_pins: pinmux_wl18xx_pins {
+	wl18xx_pins: wl18xx-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* (K18) gmii1_txclk.gpio3[9] - WL_EN */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* (K16) gmii1_txd1.gpio0[21] - WL_IRQ */
@@ -234,13 +234,37 @@
 	};
 
 	/* DCAN */
-	dcan1_pins: pinmux_dcan1_pins {
+	dcan1_pins: dcan1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)		/* (E17) uart0_rtsn.dcan1_rx */
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)		/* (E18) uart0_ctsn.dcan1_tx */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_OUTPUT, MUX_MODE7)		/* (M16) gmii1_rxd0.gpio2[21] */
 		>;
 	};
+
+	/* E1 */
+	eqep0_pins: eqep0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR0, PIN_INPUT, MUX_MODE1)		/* (B12) mcasp0_aclkr.eQEP0A_in */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSR, PIN_INPUT, MUX_MODE1)		/* (C13) mcasp0_fsr.eQEP0B_in */
+		>;
+	};
+
+	/* E2 */
+	eqep1_pins: eqep1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_INPUT, MUX_MODE2)		/* (V2) lcd_data12.eQEP1A_in */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_INPUT, MUX_MODE2)		/* (V3) lcd_data13.eQEP1B_in */
+		>;
+	};
+
+	/* E3 */
+	eqep2_pins: eqep2-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT, MUX_MODE4)		/* (T12) gpmc_ad12.eQEP2A_in */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT, MUX_MODE4)		/* (R12) gpmc_ad13.eQEP2B_in */
+		>;
+	};
 };
 
 &uart0 {
@@ -317,7 +341,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ax8975@c {
-				compatible = "ak,ak8975";
+				compatible = "asahi-kasei,ak8975";
 				reg = <0x0c>;
 			};
 		};
@@ -329,7 +353,7 @@
 	};
 };
 
-/include/ "tps65217.dtsi"
+/include/ "../../tps65217.dtsi"
 
 &tps {
 	/delete-property/ ti,pmic-shutdown-controller;
@@ -367,7 +391,6 @@
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	ti,needs-special-hs-handling;
 	keep-power-in-suspend;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
@@ -412,11 +435,182 @@
 	status = "okay";
 };
 
+&gpio0 {
+	gpio-line-names =
+		"UART3_CTS", /* M17 */
+		"UART3_RTS", /* M18 */
+		"UART2_RX", /* A17 */
+		"UART2_TX", /* B17 */
+		"I2C1_SDA", /* B16 */
+		"I2C1_SCL", /* A16 */
+		"MMC0_CD", /* C15 */
+		"SPI1_SS2", /* C18 */
+		"EQEP_1A", /* V2 */
+		"EQEP_1B", /* V3 */
+		"MDIR_2B", /* V4 */
+		"BATT_LED_2", /* T5 */
+		"I2C2_SDA", /* D18 */
+		"I2C2_SCL", /* D17 */
+		"UART1_RX", /* D16 */
+		"UART1_TX", /* D15 */
+		"MMC2_DAT1", /* J18 */
+		"MMC2_DAT2", /* K15 */
+		"NC", /* F16 */
+		"WIFI_LED", /* A15 */
+		"MOT_STBY", /* D14 */
+		"WLAN_IRQ", /* K16 */
+		"PWM_2A", /* U10 */
+		"PWM_2B", /* T10 */
+		"",
+		"",
+		"BATT_LED_4", /* T11 */
+		"BATT_LED_1", /* U12 */
+		"BT_EN", /* K17 */
+		"SPI1_SS1", /* H18 */
+		"UART4_RX", /* T17 */
+		"MDIR_1B"; /* U17 */
+};
+
+&gpio1 {
+	gpio-line-names =
+		"MMC1_DAT0", /* U7 */
+		"MMC1_DAT1", /* V7 */
+		"MMC1_DAT2", /* R8 */
+		"MMC1_DAT3", /* T8 */
+		"MMC1_DAT4", /* U8 */
+		"MMC1_DAT5", /* V8 */
+		"MMC1_DAT6", /* R9 */
+		"MMC1_DAT7", /* T9 */
+		"DCAN1_TX", /* E18 */
+		"DCAN1_RX", /* E17 */
+		"UART0_RX", /* E15 */
+		"UART0_TX", /* E16 */
+		"EQEP_2A", /* T12 */
+		"EQEP_2B", /* R12 */
+		"PRU_E_A", /* V13 */
+		"PRU_E_B", /* U13 */
+		"MDIR_2A", /* R13 */
+		"GPIO1_17", /* V14 */
+		"PWM_1A", /* U14 */
+		"PWM_1B", /* T14 */
+		"EMMC_RST", /* R14 */
+		"USR_LED_0", /* V15 */
+		"USR_LED_1", /* U15 */
+		"USR_LED_2", /* T15 */
+		"USR_LED_3", /* V16 */
+		"GPIO1_25", /* U16 */
+		"MCASP0_AXR0", /* T16 */
+		"MCASP0_AXR1", /* V17 */
+		"MCASP0_ACLKR", /* U18 */
+		"BATT_LED_3", /* V6 */
+		"MMC1_CLK", /* U9 */
+		"MMC1_CMD"; /* V9 */
+};
+
+&gpio2 {
+	gpio-line-names =
+		"MDIR_1A", /* T13 */
+		"MCASP0_FSR", /* V12 */
+		"LED_RED", /* R7 */
+		"LED_GREEN", /* T7 */
+		"MODE_BTN", /* U6 */
+		"PAUSE_BTN", /* T6 */
+		"MDIR_4A", /* R1 */
+		"MDIR_4B", /* R2 */
+		"MDIR_3B", /* R3 */
+		"MDIR_3A", /* R4 */
+		"SVO7", /* T1 */
+		"SVO8", /* T2 */
+		"SVO5", /* T3 */
+		"SVO6", /* T4 */
+		"UART5_TX", /* U1 */
+		"UART5_RX", /* U2 */
+		"SERVO_EN", /* U3 */
+		"NC", /* U4 */
+		"UART3_RX", /* L17 */
+		"UART3_TX", /* L16 */
+		"MMC2_CLK", /* L15 */
+		"DCAN1_SILENT", /* M16 */
+		"SVO1", /* U5 */
+		"SVO3", /* R5 */
+		"SVO2", /* V5 */
+		"SVO4", /* R6 */
+		"MMC0_DAT3", /* F17 */
+		"MMC0_DAT2", /* F18 */
+		"MMC0_DAT1", /* G15 */
+		"MMC0_DAT0", /* G16 */
+		"MMC0_CLK", /* G17 */
+		"MMC0_CMD"; /* G18 */
+};
+
 &gpio3 {
-	ls_buf_en {
+	gpio-line-names =
+		"MMC2_DAT3", /* H16 */
+		"GPIO3_1", /* H17 */
+		"GPIO3_2", /* J15 */
+		"MMC2_CMD", /* J16 */
+		"MMC2_DAT0", /* J17 */
+		"I2C0_SDA", /* C17 */
+		"I2C0_SCL", /* C16 */
+		"EMU1", /* C14 */
+		"EMU0", /* B14 */
+		"WL_EN", /* K18 */
+		"WL_BT_OE", /* L18 */
+		"",
+		"",
+		"NC", /* F15 */
+		"SPI1_SCK", /* A13 */
+		"SPI1_MISO", /* B13 */
+		"SPI1_MOSI", /* D12 */
+		"GPIO3_17", /* C12 */
+		"EQEP_0A", /* B12 */
+		"EQEP_0B", /* C13 */
+		"GPIO3_20", /* D13 */
+		"IMU_INT", /* A14 */
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"";
+
+	ls-buf-en-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_HIGH>;
 		output-high;
-		line-name = "LS_BUF_EN";
 	};
 };
+
+&epwmss0 {
+	status = "okay";
+};
+
+&eqep0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&eqep0_pins>;
+	status = "okay";
+};
+
+&epwmss1 {
+	status = "okay";
+};
+
+&eqep1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&eqep1_pins>;
+	status = "okay";
+};
+
+&epwmss2 {
+	status = "okay";
+};
+
+&eqep2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&eqep2_pins>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/am335x-bonegreen-common.dtsi b/arch/arm/boot/dts/ti/omap/am335x-bonegreen-common.dtsi
index 7a8826633cef..383beeddf595 100644
--- a/arch/arm/boot/dts/am335x-bonegreen-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-bonegreen-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 &ldo3_reg {
@@ -22,7 +22,7 @@
 };
 
 &am33xx_pinmux {
-	uart2_pins: uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE1)	/* spi0_sclk.uart2_rxd */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE1)	/* spi0_d0.uart2_txd */
diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/ti/omap/am335x-bonegreen-wireless.dts
index 4092cd193b8a..a4f5b5262645 100644
--- a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-bonegreen-wireless.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -18,7 +18,7 @@
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
-		startup-delay-us= <70000>;
+		startup-delay-us = <70000>;
 
 		/* WL_EN */
 		gpio = <&gpio0 26 0>;
@@ -27,13 +27,13 @@
 };
 
 &am33xx_pinmux {
-	bt_pins: pinmux_bt_pins {
+	bt_pins: bt-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_ad12.gpio1_28 BT_EN */
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad12.mmc2_dat0 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad13.mmc2_dat1 */
@@ -44,7 +44,7 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* gmii1_rxd3.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* gmii1_rxd2.uart3_txd */
@@ -53,7 +53,7 @@
 		>;
 	};
 
-	wl18xx_pins: pinmux_wl18xx_pins {
+	wl18xx_pins: wl18xx-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad10.gpio0_26 WL_EN */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad11.gpio0_27 WL_IRQ */
@@ -62,7 +62,7 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "disabled";
 };
 
@@ -75,7 +75,6 @@
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	ti,needs-special-hs-handling;
 	keep-power-in-suspend;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
@@ -102,7 +101,7 @@
 };
 
 &gpio1 {
-	ls_buf_en {
+	ls-buf-en-hog {
 		gpio-hog;
 		gpios = <29 GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -119,7 +118,7 @@
 /* an external pulldown on U21 pin 4.                                  */
 
 &gpio3 {
-	bt_aud_in {
+	bt-aud-in-hog {
 		gpio-hog;
 		gpios = <16 GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/ti/omap/am335x-bonegreen.dts
index c12bb0717779..18cc0f49e999 100644
--- a/arch/arm/boot/dts/am335x-bonegreen.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-bonegreen.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/am335x-chiliboard.dts b/arch/arm/boot/dts/ti/omap/am335x-chiliboard.dts
index b14a2759c69b..648e97fe1dfd 100644
--- a/arch/arm/boot/dts/am335x-chiliboard.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-chiliboard.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2015 Jablotron s.r.o. -- http://www.jablotron.com/
+ * Copyright (C) 2015 Jablotron s.r.o. -- https://www.jablotron.com/
  * Author: Rostislav Lisovy <lisovy@jablotron.cz>
  */
 /dts-v1/;
@@ -36,14 +36,14 @@
 };
 
 &am33xx_pinmux {
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE1)
@@ -57,7 +57,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -72,7 +72,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* mdio_data.mdio_data */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -81,7 +81,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -89,13 +89,13 @@
 		>;
 	};
 
-	usb1_drvvbus: usb1_drvvbus {
+	usb1_drvvbus: usb1-drvvbus-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_USB1_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	sd_pins: pinmux_sd_card {
+	sd_pins: sd-card-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT, MUX_MODE0)
@@ -107,7 +107,7 @@
 		>;
 	};
 
-	led_gpio_pins: led_gpio_pins {
+	led_gpio_pins: led-gpio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_EMU0, PIN_OUTPUT, MUX_MODE7) /* emu0.gpio3_7 */
 			AM33XX_PADCONF(AM335X_PIN_EMU1, PIN_OUTPUT, MUX_MODE7) /* emu1.gpio3_8 */
@@ -128,28 +128,31 @@
 };
 
 /* Ethernet */
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 /* USB */
diff --git a/arch/arm/boot/dts/am335x-chilisom.dtsi b/arch/arm/boot/dts/ti/omap/am335x-chilisom.dtsi
index b31e2f7a4ad9..bd43da6356b6 100644
--- a/arch/arm/boot/dts/am335x-chilisom.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-chilisom.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2015 Jablotron s.r.o. -- http://www.jablotron.com/
+ * Copyright (C) 2015 Jablotron s.r.o. -- https://www.jablotron.com/
  * Author: Rostislav Lisovy <lisovy@jablotron.cz>
  */
 #include "am33xx.dtsi"
@@ -25,14 +25,14 @@
 &am33xx_pinmux {
 	pinctrl-names = "default";
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	nandflash_pins: nandflash_pins {
+	nandflash_pins: nandflash-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLDOWN, MUX_MODE0)
@@ -66,7 +66,7 @@
 
 };
 
-/include/ "tps65217.dtsi"
+/include/ "../../tps65217.dtsi"
 
 &tps {
 	regulators {
diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/ti/omap/am335x-cm-t335.dts
index c6fe9db660e2..72990e7ffe10 100644
--- a/arch/arm/boot/dts/am335x-cm-t335.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-cm-t335.dts
@@ -88,14 +88,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&bluetooth_pins>;
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			/* uart0_ctsn.i2c1_sda */
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE2)
@@ -104,14 +104,14 @@
 		>;
 	};
 
-	gpio_led_pins: pinmux_gpio_led_pins {
+	gpio_led_pins: gpio-led-pins {
 		pinctrl-single,pins = <
 			/* gpmc_csn3.gpio2_0 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_OUTPUT, MUX_MODE7)
 		>;
 	};
 
-	nandflash_pins: pinmux_nandflash_pins {
+	nandflash_pins: nandflash-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -122,7 +122,7 @@
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0)
-			/* gpmc_wpn.gpio0_30 */
+			/* gpmc_wpn.gpio0_31 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0)
@@ -132,14 +132,14 @@
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -148,7 +148,7 @@
 		>;
 	};
 
-	dcan0_pins: pinmux_dcan0_pins {
+	dcan0_pins: dcan0-pins {
 		pinctrl-single,pins = <
 			/* uart1_ctsn.dcan0_tx */
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE2)
@@ -157,7 +157,7 @@
 		>;
 	};
 
-	dcan1_pins: pinmux_dcan1_pins {
+	dcan1_pins: dcan1-pins {
 		pinctrl-single,pins = <
 			/* uart1_rxd.dcan1_tx */
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT, MUX_MODE2)
@@ -166,13 +166,13 @@
 		>;
 	};
 
-	ecap0_pins: pinmux_ecap0_pins {
+	ecap0_pins: ecap0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, 0x0, MUX_MODE0)
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			/* mii1_tx_en.rgmii1_tctl */
@@ -202,7 +202,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -220,14 +220,14 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -235,7 +235,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -246,7 +246,7 @@
 		>;
 	};
 
-	spi0_pins: pinmux_spi0_pins {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT_PULLUP, MUX_MODE0)
@@ -257,7 +257,7 @@
 	};
 
 	/* wl1271 bluetooth */
-	bluetooth_pins: pinmux_bluetooth_pins {
+	bluetooth_pins: bluetooth-pins {
 		pinctrl-single,pins = <
 			/* XDMA_EVENT_INTR0.gpio0_19 - bluetooth enable */
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLUP, MUX_MODE7)
@@ -265,7 +265,7 @@
 	};
 
 	/* TLV320AIC23B codec */
-	mcasp1_pins: pinmux_mcasp1_pins {
+	mcasp1_pins: mcasp1-pins {
 		pinctrl-single,pins = <
 			/* MII1_CRS.mcasp1_aclkx */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE4)
@@ -279,7 +279,7 @@
 	};
 
 	/* wl1271 WiFi */
-	wifi_pins: pinmux_wifi_pins {
+	wifi_pins: wifi-pins {
 		pinctrl-single,pins = <
 			/* EMU1.gpio3_8 - WiFi IRQ */
 			AM33XX_PADCONF(AM335X_PIN_EMU1, PIN_INPUT_PULLUP, MUX_MODE7)
@@ -325,7 +325,7 @@ status = "okay";
 	tlv320aic23: codec@1a {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1a>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 };
@@ -333,7 +333,7 @@ status = "okay";
 &epwmss0 {
 	status = "okay";
 
-	ecap0: ecap@100 {
+	ecap0: pwm@100 {
 		status = "okay";
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap0_pins>;
@@ -413,28 +413,31 @@ status = "okay";
 	status = "okay";
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	slaves = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 &mmc1 {
@@ -488,7 +491,7 @@ status = "okay";
 		tx-num-evt = <1>;
 		rx-num-evt = <1>;
 
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 };
 
@@ -496,7 +499,7 @@ status = "okay";
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
-	ti,pindir-d0-out-d1-in = <1>;
+	ti,pindir-d0-out-d1-in;
 	/* WLS1271 WiFi */
 	wlcore: wlcore@1 {
 		compatible = "ti,wl1271";
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/ti/omap/am335x-evm.dts
index 6f0a6be93098..61bf8bcd4c4e 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -92,20 +92,18 @@
 				0x0201006c>;	/* DOWN */
 	};
 
-	gpio_keys: volume_keys0 {
+	gpio_keys: volume-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
-		switch9 {
+		switch-9 {
 			label = "volume-up";
 			linux,code = <115>;
 			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		switch10 {
+		switch-10 {
 			label = "volume-down";
 			linux,code = <114>;
 			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
@@ -113,7 +111,7 @@
 		};
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&ecap0 0 50000 0>;
 		brightness-levels = <0 51 53 56 62 75 101 152 255>;
@@ -121,35 +119,15 @@
 	};
 
 	panel {
-		compatible = "ti,tilcdc,panel";
-		status = "okay";
+		compatible = "tfc,s9700rtwv43tr-01b";
+
 		pinctrl-names = "default";
 		pinctrl-0 = <&lcd_pins_s0>;
-		panel-info {
-			ac-bias           = <255>;
-			ac-bias-intrpt    = <0>;
-			dma-burst-sz      = <16>;
-			bpp               = <32>;
-			fdd               = <0x80>;
-			sync-edge         = <0>;
-			sync-ctrl         = <1>;
-			raster-order      = <0>;
-			fifo-th           = <0>;
-		};
+		backlight = <&backlight>;
 
-		display-timings {
-			800x480p62 {
-				clock-frequency = <30000000>;
-				hactive = <800>;
-				vactive = <480>;
-				hfront-porch = <39>;
-				hback-porch = <39>;
-				hsync-len = <47>;
-				vback-porch = <29>;
-				vfront-porch = <13>;
-				vsync-len = <2>;
-				hsync-active = <1>;
-				vsync-active = <1>;
+		port {
+			panel_0: endpoint {
+				remote-endpoint = <&lcdc_0>;
 			};
 		};
 	};
@@ -185,7 +163,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
 
-	matrix_keypad_s0: matrix_keypad_s0 {
+	matrix_keypad_s0: matrix-keypad-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a6.gpio1_22 */
@@ -195,35 +173,35 @@
 		>;
 	};
 
-	volume_keys_s0: volume_keys_s0 {
+	volume_keys_s0: volume-keys-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* spi0_sclk.gpio0_2 */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* spi0_d0.gpio0_3 */
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)	/* i2c0_sda.i2c0_sda */
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE2)	/* spi0_d1.i2c1_sda */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE2)	/* spi0_cs0.i2c1_scl */
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -232,13 +210,13 @@
 		>;
 	};
 
-	clkout2_pin: pinmux_clkout2_pin {
+	clkout2_pin: clkout2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3)	/* xdma_event_intr1.clkout2 */
 		>;
 	};
 
-	nandflash_pins_s0: nandflash_pins_s0 {
+	nandflash_pins_s0: nandflash-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -249,7 +227,7 @@
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_31 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_OUTPUT, MUX_MODE0)
@@ -258,13 +236,13 @@
 		>;
 	};
 
-	ecap0_pins: backlight_pins {
+	ecap0_pins: backlight-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, 0x0, MUX_MODE0)
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
@@ -282,7 +260,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -300,7 +278,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -308,7 +286,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -316,7 +294,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7)		/* spi0_cs1.gpio0_6 */
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -329,7 +307,7 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */
@@ -340,7 +318,7 @@
 		>;
 	};
 
-	wlan_pins: pinmux_wlan_pins {
+	wlan_pins: wlan-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a0.gpio1_16 */
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT, MUX_MODE7)		/* mcasp0_ahclkr.gpio3_17 */
@@ -348,7 +326,7 @@
 		>;
 	};
 
-	lcd_pins_s0: lcd_pins_s0 {
+	lcd_pins_s0: lcd-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_OUTPUT, MUX_MODE1)		/* gpmc_ad8.lcd_data23 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_OUTPUT, MUX_MODE1)		/* gpmc_ad9.lcd_data22 */
@@ -381,7 +359,7 @@
 		>;
 	};
 
-	mcasp1_pins: mcasp1_pins {
+	mcasp1_pins: mcasp1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
@@ -390,7 +368,7 @@
 		>;
 	};
 
-	mcasp1_pins_sleep: mcasp1_pins_sleep {
+	mcasp1_pins_sleep: mcasp1-sleep-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -399,7 +377,7 @@
 		>;
 	};
 
-	dcan1_pins_default: dcan1_pins_default {
+	dcan1_pins_default: dcan1-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2) /* uart0_ctsn.d_can1_tx */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE2) /* uart0_rtsn.d_can1_rx */
@@ -500,6 +478,12 @@
 	status = "okay";
 
 	blue-and-red-wiring = "crossed";
+
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <&panel_0>;
+		};
+	};
 };
 
 &elm {
@@ -509,7 +493,7 @@
 &epwmss0 {
 	status = "okay";
 
-	ecap0: ecap@100 {
+	ecap0: pwm@100 {
 		status = "okay";
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap0_pins>;
@@ -560,7 +544,7 @@
 		#size-cells = <1>;
 		partition@0 {
 			label = "NAND.SPL";
-			reg = <0x00000000 0x000020000>;
+			reg = <0x00000000 0x00020000>;
 		};
 		partition@1 {
 			label = "NAND.SPL.backup1";
@@ -601,7 +585,7 @@
 	};
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &mcasp1 {
 	#sound-dai-cells = <0>;
@@ -698,28 +682,31 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	slaves = <1>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	 status = "disabled";
 };
 
 &tscadc {
@@ -757,8 +744,7 @@
 	bus-width = <4>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc3_pins &wlan_pins>;
-	ti,non-removable;
-	ti,needs-special-hs-handling;
+	non-removable;
 	cap-power-off-card;
 	keep-power-in-suspend;
 
@@ -790,3 +776,11 @@
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
 };
+
+&pruss_tm {
+	status = "okay";
+};
+
+&wkup_m3_ipc {
+	firmware-name = "am335x-evm-scale-data.bin";
+};
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/ti/omap/am335x-evmsk.dts
index a97f9df460c1..57f78846c42d 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-evmsk.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -183,36 +183,16 @@
 	};
 
 	panel {
-		compatible = "ti,tilcdc,panel";
+		compatible = "newhaven,nhd-4.3-480272ef-atxl";
+
 		pinctrl-names = "default", "sleep";
 		pinctrl-0 = <&lcd_pins_default>;
 		pinctrl-1 = <&lcd_pins_sleep>;
 		backlight = <&lcd_bl>;
-		status = "okay";
-		panel-info {
-			ac-bias		= <255>;
-			ac-bias-intrpt	= <0>;
-			dma-burst-sz	= <16>;
-			bpp		= <32>;
-			fdd		= <0x80>;
-			sync-edge	= <0>;
-			sync-ctrl	= <1>;
-			raster-order	= <0>;
-			fifo-th		= <0>;
-		};
-		display-timings {
-			480x272 {
-				hactive		= <480>;
-				vactive		= <272>;
-				hback-porch	= <43>;
-				hfront-porch	= <8>;
-				hsync-len	= <4>;
-				vback-porch	= <12>;
-				vfront-porch	= <4>;
-				vsync-len	= <10>;
-				clock-frequency = <9000000>;
-				hsync-active	= <0>;
-				vsync-active	= <0>;
+
+		port {
+			panel_0: endpoint {
+				remote-endpoint = <&lcdc_0>;
 			};
 		};
 	};
@@ -222,7 +202,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
 
-	lcd_pins_default: lcd_pins_default {
+	lcd_pins_default: lcd-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_OUTPUT, MUX_MODE1)	/* gpmc_ad8.lcd_data23 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_OUTPUT, MUX_MODE1)	/* gpmc_ad9.lcd_data22 */
@@ -255,7 +235,7 @@
 		>;
 	};
 
-	lcd_pins_sleep: lcd_pins_sleep {
+	lcd_pins_sleep: lcd-sleep-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad8.lcd_data23 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad9.lcd_data22 */
@@ -289,7 +269,7 @@
 	};
 
 
-	user_leds_s0: user_leds_s0 {
+	user_leds_s0: user-leds-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad4.gpio1_4 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad5.gpio1_5 */
@@ -298,7 +278,7 @@
 		>;
 	};
 
-	gpio_keys_s0: gpio_keys_s0 {
+	gpio_keys_s0: gpio-keys-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_oen_ren.gpio2_3 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_advn_ale.gpio2_2 */
@@ -307,33 +287,33 @@
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	clkout2_pin: pinmux_clkout2_pin {
+	clkout2_pin: clkout2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3)	/* xdma_event_intr1.clkout2 */
 		>;
 	};
 
-	ecap2_pins: backlight_pins {
+	ecap2_pins: backlight-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, 0x0, MUX_MODE4)	/* mcasp0_ahclkr.ecap2_in_pwm2_out */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
@@ -365,7 +345,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -397,7 +377,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -405,7 +385,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -413,7 +393,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7) 		/* spi0_cs1.gpio0_6 */
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -426,7 +406,7 @@
 		>;
 	};
 
-	mcasp1_pins: mcasp1_pins {
+	mcasp1_pins: mcasp1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
@@ -435,7 +415,7 @@
 		>;
 	};
 
-	mcasp1_pins_sleep: mcasp1_pins_sleep {
+	mcasp1_pins_sleep: mcasp1-sleep-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -444,7 +424,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7) /* gpmc_wpn.gpio0_31 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */
@@ -456,7 +436,7 @@
 		>;
 	};
 
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gpmc_csn0.gpio1_29 */
 		>;
@@ -530,14 +510,14 @@
 &epwmss2 {
 	status = "okay";
 
-	ecap2: ecap@100 {
+	ecap2: pwm@100 {
 		status = "okay";
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap2_pins>;
 	};
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vbat>;
@@ -616,19 +596,17 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -639,16 +617,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &mmc1 {
@@ -668,14 +646,14 @@
 	status = "okay";
 };
 
-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };
 
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&wl12xx_vmmc>;
-	ti,non-removable;
+	non-removable;
 	bus-width = <4>;
 	cap-power-off-card;
 	keep-power-in-suspend;
@@ -725,9 +703,23 @@
 	status = "okay";
 
 	blue-and-red-wiring = "crossed";
+
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <&panel_0>;
+		};
+	};
 };
 
 &rtc {
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
 };
+
+&pruss_tm {
+	status = "okay";
+};
+
+&wkup_m3_ipc {
+	firmware-name = "am335x-evm-scale-data.bin";
+};
diff --git a/arch/arm/boot/dts/am335x-guardian.dts b/arch/arm/boot/dts/ti/omap/am335x-guardian.dts
index 81e0f63e94d3..205fe0ed7352 100644
--- a/arch/arm/boot/dts/am335x-guardian.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-guardian.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  * Copyright (C) 2018 Robert Bosch Power Tools GmbH
  */
 /dts-v1/;
@@ -29,39 +29,42 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	guardian_buttons: gpio-keys {
 		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pins>;
+		pinctrl-0 = <&guardian_button_pins>;
+		compatible = "gpio-keys";
+
+		select-button {
+			label = "guardian-select-button";
+			linux,code = <KEY_5>;
+			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
 
-		button21 {
+		power-button {
 			label = "guardian-power-button";
 			linux,code = <KEY_POWER>;
-			gpios = <&gpio2 21 0>;
+			gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 	};
 
-	leds {
-		compatible = "gpio-leds";
+	guardian_leds: gpio-leds {
 		pinctrl-names = "default";
-		pinctrl-0 = <&leds_pins>;
+		pinctrl-0 = <&guardian_led_pins>;
+		compatible = "gpio-leds";
 
-		led1 {
-			label = "green:heartbeat";
-			gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+		life-led {
+			label = "guardian:life-led";
+			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
+	};
 
-		led2 {
-			label = "green:mmc0";
-			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
 	};
 
 	panel {
@@ -100,19 +103,37 @@
 
 	};
 
-	pwm7: dmtimer-pwm {
+	guardian_beeper: pwm-7 {
 		compatible = "ti,omap-dmtimer-pwm";
+		#pwm-cells = <3>;
 		ti,timers = <&timer7>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&dmtimer7_pins>;
+		pinctrl-0 = <&guardian_beeper_pins>;
+		ti,clock-source = <0x01>;
 	};
 
-	vmmcsd_fixed: regulator-3v3 {
+	vmmcsd_fixed: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	mt_keypad: mt_keypad@0 {
+		compatible = "gpio-mt-keypad";
+		debounce-delay-ms = <10>;
+		col-scan-delay-us = <2>;
+		keypad,num-lines = <5>;
+		linux,no-autorepeat;
+		gpio-activelow;
+		line-gpios = <
+			&gpio1 24 GPIO_ACTIVE_LOW    /*gpio_56*/
+			&gpio1 23 GPIO_ACTIVE_LOW    /*gpio_55*/
+			&gpio1 22 GPIO_ACTIVE_LOW    /*gpio_54*/
+			&gpio1 20 GPIO_ACTIVE_LOW    /*gpio_52*/
+			&gpio1 16 GPIO_ACTIVE_LOW    /*gpio_48*/
+		>;
+	};
 };
 
 &elm {
@@ -132,28 +153,29 @@
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
 		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
+		ti,nand-xfer-type = "prefetch-dma";
 		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <44>;
-		gpmc,cs-wr-off-ns = <44>;
-		gpmc,adv-on-ns = <6>;
-		gpmc,adv-rd-off-ns = <34>;
-		gpmc,adv-wr-off-ns = <44>;
+		gpmc,cs-rd-off-ns = <30>;
+		gpmc,cs-wr-off-ns = <30>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <30>;
+		gpmc,adv-wr-off-ns = <30>;
 		gpmc,we-on-ns = <0>;
-		gpmc,we-off-ns = <40>;
-		gpmc,oe-on-ns = <0>;
-		gpmc,oe-off-ns = <54>;
-		gpmc,access-ns = <64>;
-		gpmc,rd-cycle-ns = <82>;
-		gpmc,wr-cycle-ns = <82>;
+		gpmc,we-off-ns = <15>;
+		gpmc,oe-on-ns = <1>;
+		gpmc,oe-off-ns = <15>;
+		gpmc,access-ns = <30>;
+		gpmc,rd-cycle-ns = <30>;
+		gpmc,wr-cycle-ns = <30>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wr-access-ns = <40>;
+		gpmc,wr-access-ns = <0>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 
 		/*
@@ -197,18 +219,33 @@
 		};
 
 		partition@6 {
-			label = "u-boot-env";
-			reg = <0x300000 0x40000>;
+			label = "u-boot-2";
+			reg = <0x300000 0x100000>;
 		};
 
 		partition@7 {
-			label = "u-boot-env.backup1";
-			reg = <0x340000 0x40000>;
+			label = "u-boot-2.backup1";
+			reg = <0x400000 0x100000>;
 		};
 
 		partition@8 {
+			label = "u-boot-env";
+			reg = <0x500000 0x40000>;
+		};
+
+		partition@9 {
+			label = "u-boot-env.backup1";
+			reg = <0x540000 0x40000>;
+		};
+
+		partition@10 {
+			label = "splash-screen";
+			reg = <0x580000 0x40000>;
+		};
+
+		partition@11 {
 			label = "UBI";
-			reg = <0x380000 0x1fc80000>;
+			reg = <0x5c0000 0x1fa40000>;
 		};
 	};
 };
@@ -227,6 +264,11 @@
 &lcdc {
 	blue-and-red-wiring = "crossed";
 	status = "okay";
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <0>;
+		};
+	};
 };
 
 &mmc1 {
@@ -241,7 +283,6 @@
 &rtc {
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
-	system-power-controller;
 };
 
 &spi0 {
@@ -251,17 +292,37 @@
 	status = "okay";
 };
 
-#include "tps65217.dtsi"
+#include "../../tps65217.dtsi"
 
 &tps {
+  /*
+   * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only
+   * mode") at poweroff.  Most BeagleBone versions do not support RTC-only
+   * mode and risk hardware damage if this mode is entered.
+   *
+   * For details, see linux-omap mailing list May 2015 thread
+   *  [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller
+   * In particular, messages:
+   *  http://www.spinics.net/lists/linux-omap/msg118585.html
+   *  http://www.spinics.net/lists/linux-omap/msg118615.html
+   *
+   * You can override this later with
+   *  &tps {  /delete-property/ ti,pmic-shutdown-controller;  }
+   * if you want to use RTC-only mode and made sure you are not affected
+   * by the hardware problems. (Tip: double-check by performing a current
+   * measurement after shutdown: it should be less than 1 mA.)
+   */
 	ti,pmic-shutdown-controller;
 	interrupt-parent = <&intc>;
 	interrupts = <7>; /* NMI */
 
 	backlight {
 		isel = <1>;  /* 1 - ISET1, 2 ISET2 */
-		fdim = <100>; /* TPS65217_BL_FDIM_100HZ */
-		default-brightness = <100>;
+		fdim = <500>; /* TPS65217_BL_FDIM_500HZ */
+		default-brightness = <50>;
+		/* 1(on) - enable current sink, while initialization */
+		/* 0(off) - disable current sink, while initialization */
+		isink-en = <1>;
 	};
 
 	regulators {
@@ -271,6 +332,7 @@
 		};
 
 		dcdc2_reg: regulator@1 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
 			regulator-max-microvolt = <1351500>;
@@ -279,6 +341,7 @@
 		};
 
 		dcdc3_reg: regulator@2 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
 			regulator-max-microvolt = <1150000>;
@@ -318,171 +381,364 @@
 	};
 };
 
+&gpio0 {
+	gpio-line-names =
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"MirxWakeup",
+		"",
+		"";
+};
+
+&gpio3 {
+	ti,gpio-always-on;
+	ti,no-reset-on-init;
+	gpio-line-names =
+		"",
+		"MirxBtReset",
+		"",
+		"CcVolAdcEn",
+		"MirxBlePause",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"AspEn",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"BatVolAdcEn",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 	status = "okay";
 };
 
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
 &usb0 {
 	dr_mode = "peripheral";
 };
 
 &usb1 {
 	dr_mode = "host";
+	/delete-property/dmas;
+	/delete-property/dma-names;
 };
 
 &am33xx_pinmux {
 	pinctrl-names = "default";
-	pinctrl-0 = <&clkout2_pin &gpio_pins>;
+	pinctrl-0 = <&clkout2_pin &guardian_interface_pins>;
 
-	clkout2_pin: pinmux_clkout2_pin {
+	clkout2_pin: clkout2-pins {
 		pinctrl-single,pins = <
+			/* xdma_event_intr1.clkout2 */
 			AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
 		>;
 	};
 
-	dmtimer7_pins: pinmux_dmtimer7_pins {
+	guardian_interface_pins: interface-pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE5)
+			/* ADC_BATSENSE_EN */
+			/* (A14) MCASP0_AHCLKx.gpio3[21] */
+			AM33XX_IOPAD(0x9ac, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* ADC_COINCELL_EN */
+			/* (J16) MII1_TX_EN.gpio3[3] */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* ASP_ENABLE */
+			/* (A13) MCASP0_ACLKx.gpio3[14] */
+			AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLUP | MUX_MODE7)
+			/* (D16) uart1_rxd.uart1_rxd */
+			AM33XX_IOPAD(0x980, PIN_INPUT | MUX_MODE7)
+			/* (D15) uart1_txd.uart1_txd */
+			AM33XX_IOPAD(0x984, PIN_INPUT | MUX_MODE7)
+			/*SWITCH-OFF_3V6*/
+			/* (M18) gpio0[1] */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE7)
+			/* MIRACULIX */
+			/* (H17) gmii1_crs.gpio3[1] */
+			AM33XX_IOPAD(0x90c, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* (H18) rmii1_refclk.gpio0[29] */
+			AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* (J18) gmii1_txd3.gpio0[16] */
+			AM33XX_IOPAD(0x91c, PIN_INPUT           | MUX_MODE7 )
+			/* (J17) gmii1_rxdv.gpio3[4] */
+			AM33XX_IOPAD(0x918, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
 		>;
 	};
 
-	gpio_keys_pins: pinmux_gpio_keys_pins {
+	guardian_beeper_pins: dmtimer7-pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE5) /* (E18) timer7 */
 		>;
 	};
 
-	gpio_pins: pinmux_gpio_pins {
+	guardian_button_pins: guardian-button-pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x928, PIN_OUTPUT | MUX_MODE7)
-			AM33XX_IOPAD(0x990, PIN_OUTPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE7) /* (M16) gmii1_rxd0.gpio2[21] */
+			AM33XX_IOPAD(0x884, PIN_INPUT | MUX_MODE7) /* (V9)  gpmc_csn2.gpio1[31] */
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	lcd_disen_pins: pinmux_lcd_disen_pins {
+	led_bl_pins: gpio-led-bl-pins {
 		pinctrl-single,pins = <
+			/* P9_14, gpmc_a[2].GPIO1[18] (backlight control) */
+			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE7)
+		>;
+	};
+
+	lcd_disen_pins: lcd-disen-pins {
+		pinctrl-single,pins = <
+			/* P9_27, mcasp0_fsr.gpio3[19] (lcd_disen) */
 			AM33XX_IOPAD(0x9a4, PIN_OUTPUT_PULLUP | SLEWCTRL_SLOW | MUX_MODE7)
 		>;
 	};
 
-	lcd_pins_default: pinmux_lcd_pins_default {
+	lcd_pins_default: lcd-default-pins {
 		pinctrl-single,pins = <
+			/* (U10) gpmc_ad8.lcd_data23 */
 			AM33XX_IOPAD(0x820, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (T10) gpmc_ad9.lcd_data22 */
 			AM33XX_IOPAD(0x824, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (T11) gpmc_ad10.lcd_data21 */
 			AM33XX_IOPAD(0x828, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (U12) gpmc_ad11.lcd_data20 */
 			AM33XX_IOPAD(0x82c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (T12) gpmc_ad12.lcd_data19 */
 			AM33XX_IOPAD(0x830, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (R12) gpmc_ad13.lcd_data18 */
 			AM33XX_IOPAD(0x834, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (V13) gpmc_ad14.lcd_data17 */
 			AM33XX_IOPAD(0x838, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (U13) gpmc_ad15.lcd_data16 */
 			AM33XX_IOPAD(0x83c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* lcd_data0.lcd_data0 */
 			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data1.lcd_data1 */
 			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data2.lcd_data2 */
 			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data3.lcd_data3 */
 			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data4.lcd_data4 */
 			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data5.lcd_data5 */
 			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data6.lcd_data6 */
 			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data7.lcd_data7 */
 			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data8.lcd_data8 */
 			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data9.lcd_data9 */
 			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data10.lcd_data10 */
 			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data11.lcd_data11 */
 			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data12.lcd_data12 */
 			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data13.lcd_data13 */
 			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data14.lcd_data14 */
 			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data15.lcd_data15 */
 			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_vsync.lcd_vsync */
 			AM33XX_IOPAD(0x8e0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_hsync.lcd_hsync */
 			AM33XX_IOPAD(0x8e4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_pclk.lcd_pclk */
 			AM33XX_IOPAD(0x8e8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_ac_bias_en.lcd_ac_bias_en */
 			AM33XX_IOPAD(0x8ec, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
 		>;
 	};
 
-	lcd_pins_sleep: pinmux_lcd_pins_sleep {
+	lcd_pins_sleep: lcd-sleep-pins {
 		pinctrl-single,pins = <
+			/* lcd_data0.lcd_data0 */
 			AM33XX_IOPAD(0x8a0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data1.lcd_data1 */
 			AM33XX_IOPAD(0x8a4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data2.lcd_data2 */
 			AM33XX_IOPAD(0x8a8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data3.lcd_data3 */
 			AM33XX_IOPAD(0x8ac, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data4.lcd_data4 */
 			AM33XX_IOPAD(0x8b0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data5.lcd_data5 */
 			AM33XX_IOPAD(0x8b4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data6.lcd_data6 */
 			AM33XX_IOPAD(0x8b8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data7.lcd_data7 */
 			AM33XX_IOPAD(0x8bc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data8.lcd_data8 */
 			AM33XX_IOPAD(0x8c0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data9.lcd_data9 */
 			AM33XX_IOPAD(0x8c4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data10.lcd_data10 */
 			AM33XX_IOPAD(0x8c8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data11.lcd_data11 */
 			AM33XX_IOPAD(0x8cc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data12.lcd_data12 */
 			AM33XX_IOPAD(0x8d0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data13.lcd_data13 */
 			AM33XX_IOPAD(0x8d4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data14.lcd_data14 */
 			AM33XX_IOPAD(0x8d8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data15.lcd_data15 */
 			AM33XX_IOPAD(0x8dc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_vsync.lcd_vsync */
 			AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_hsync.lcd_hsync */
 			AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_pclk.lcd_pclk */
 			AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_ac_bias_en.lcd_ac_bias_en */
 			AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
 		>;
 	};
 
-	leds_pins: pinmux_leds_pins {
+	guardian_led_pins: guardian-led-pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x868, PIN_OUTPUT | MUX_MODE7)
-			AM33XX_IOPAD(0x86c, PIN_OUTPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x868, PIN_OUTPUT | MUX_MODE7) /* (T16) gpmc_a10.gpio1[26] */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat3.mmc0_dat3 */
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat2.mmc0_dat2 */
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat1.mmc0_dat1 */
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat0.mmc0_dat0 */
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_clk.mmc0_clk */
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_cmd.mmc0_cmd */
+			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7)         /* GPIO0_6 */
 		>;
 	};
 
-	spi0_pins: pinmux_spi0_pins {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
+			/* SPI0_CLK  - spi0_clk.spi */
 			AM33XX_IOPAD(0x950, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
+			/* SPI0_MOSI - spi0_d0.spi0 */
 			AM33XX_IOPAD(0x954, PIN_OUTPUT_PULLUP | MUX_MODE0)
+			/* SPI0_MISO - spi0_d1.spi0 */
 			AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* SPI0_CS0 - spi */
 			AM33XX_IOPAD(0x95c, PIN_OUTPUT_PULLUP | MUX_MODE0)
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
+			/* uart0_rxd.uart0_rxd */
 			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* uart0_txd.uart0_txd */
 			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
 		>;
 	};
 
-	nandflash_pins: pinmux_nandflash_pins {
+	uart2_pins: uart2-pins {
+		pinctrl-single,pins = <
+			/* K18 uart2_rxd.mirx_txd */
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1)
+			/* L18 uart2_txd.mirx_rxd */
+			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1)
+		>;
+	};
+
+	nandflash_pins: nandflash-pins {
 		pinctrl-single,pins = <
+			/* (U7) gpmc_ad0.gpmc_ad0 */
 			AM33XX_IOPAD(0x800, PIN_INPUT | MUX_MODE0)
+			/* (V7) gpmc_ad1.gpmc_ad1 */
 			AM33XX_IOPAD(0x804, PIN_INPUT | MUX_MODE0)
+			/* (R8) gpmc_ad2.gpmc_ad2 */
 			AM33XX_IOPAD(0x808, PIN_INPUT | MUX_MODE0)
+			/* (T8) gpmc_ad3.gpmc_ad3 */
 			AM33XX_IOPAD(0x80c, PIN_INPUT | MUX_MODE0)
+			/* (U8) gpmc_ad4.gpmc_ad4 */
 			AM33XX_IOPAD(0x810, PIN_INPUT | MUX_MODE0)
+			/* (V8) gpmc_ad5.gpmc_ad5 */
 			AM33XX_IOPAD(0x814, PIN_INPUT | MUX_MODE0)
+			/* (R9) gpmc_ad6.gpmc_ad6 */
 			AM33XX_IOPAD(0x818, PIN_INPUT | MUX_MODE0)
+			/* (T9) gpmc_ad7.gpmc_ad7 */
 			AM33XX_IOPAD(0x81c, PIN_INPUT | MUX_MODE0)
+			/* (T17) gpmc_wait0.gpmc_wait0 */
 			AM33XX_IOPAD(0x870, PIN_INPUT | MUX_MODE0)
+			/* (U17) gpmc_wpn.gpmc_wpn */
 			AM33XX_IOPAD(0x874, PIN_OUTPUT | MUX_MODE0)
+			/* (V6) gpmc_csn0.gpmc_csn0 */
 			AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0)
+			/* (R7) gpmc_advn_ale.gpmc_advn_ale */
 			AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0)
+			/* (T7) gpmc_oen_ren.gpmc_oen_ren */
 			AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0)
+			/* (U6) gpmc_wen.gpmc_wen */
 			AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0)
+			/* (T6) gpmc_be0n_cle.gpmc_be0n_cle */
 			AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0)
 		>;
 	};
diff --git a/arch/arm/boot/dts/am335x-icev2.dts b/arch/arm/boot/dts/ti/omap/am335x-icev2.dts
index 204bccfcc110..3c4228927f56 100644
--- a/arch/arm/boot/dts/am335x-icev2.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-icev2.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -152,7 +152,7 @@
 };
 
 &am33xx_pinmux {
-	user_leds: user_leds {
+	user_leds: user-leds-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT, MUX_MODE7) /* (J18) gmii1_txd3.gpio0[16] */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT, MUX_MODE7) /* (K15) gmii1_txd2.gpio0[17] */
@@ -163,7 +163,7 @@
 		>;
 	};
 
-	mmc0_pins_default: mmc0_pins_default {
+	mmc0_pins_default: mmc0-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -174,14 +174,14 @@
 		>;
 	};
 
-	i2c0_pins_default: i2c0_pins_default {
+	i2c0_pins_default: i2c0-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE0)
 		>;
 	};
 
-	spi0_pins_default: spi0_pins_default {
+	spi0_pins_default: spi0-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -192,14 +192,14 @@
 		>;
 	};
 
-	uart3_pins_default: uart3_pins_default {
+	uart3_pins_default: uart3-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1) /* (L17) gmii1_rxd3.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLUP, MUX_MODE1) /* (L16) gmii1_rxd2.uart3_txd */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1, RMII mode */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_crs.rmii1_crs_dv */
@@ -222,7 +222,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -246,7 +246,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -254,7 +254,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -287,6 +287,19 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
+
+	/* osd9616p0899-10 */
+	display@3c {
+		compatible = "solomon,ssd1306fb-i2c";
+		reg = <0x3c>;
+		solomon,height = <16>;
+		solomon,width = <96>;
+		solomon,com-seq;
+		solomon,com-invdir;
+		solomon,page-offset = <0>;
+		solomon,prechargep1 = <2>;
+		solomon,prechargep2 = <13>;
+	};
 };
 
 &spi0 {
@@ -347,7 +360,7 @@
 	};
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vbat>;
@@ -445,14 +458,14 @@
 };
 
 &gpio3 {
-	p4 {
+	pr1-mii-ctl-hog {
 		gpio-hog;
 		gpios = <4 GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PR1_MII_CTRL";
 	};
 
-	p10 {
+	mux-mii-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_HIGH>;
 		/* ETH1 mux: Low for MII-PRU, high for RMII-CPSW */
@@ -461,31 +474,29 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	dual_emac;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 	reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
 	reset-delay-us = <2>;   /* PHY datasheet states 1uS min */
 
@@ -497,3 +508,11 @@
 		reg = <3>;
 	};
 };
+
+&pruss_tm {
+	status = "okay";
+};
+
+&rtc {
+	system-power-controller;
+};
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/ti/omap/am335x-igep0033.dtsi
index c9f354fc984a..e85c33fd42f0 100644
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-igep0033.dtsi
@@ -52,14 +52,14 @@
 };
 
 &am33xx_pinmux {
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	nandflash_pins: pinmux_nandflash_pins {
+	nandflash_pins: nandflash-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -70,7 +70,7 @@
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_31 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_OUTPUT, MUX_MODE0)
@@ -79,26 +79,25 @@
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	leds_pins: pinmux_leds_pins {
+	leds_pins: leds-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a7.gpio1_23 */
 		>;
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
 };
 
-&davinci_mdio {
-	status = "okay";
+&davinci_mdio_sw {
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -109,15 +108,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
+	ti,dual-emac-pvid = <2>;
 };
 
 &elm {
@@ -168,7 +168,7 @@
 		/* MTD partition table */
 		partition@0 {
 			label = "SPL";
-			reg = <0x00000000 0x000080000>;
+			reg = <0x00000000 0x00080000>;
 		};
 
 		partition@1 {
@@ -188,7 +188,7 @@
 
 		partition@4 {
 			label = "File System";
-			reg = <0x00780000 0x007880000>;
+			reg = <0x00780000 0x07880000>;
 		};
 	};
 };
@@ -221,7 +221,7 @@
 	dr_mode = "host";
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vbat>;
diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/ti/omap/am335x-lxm.dts
index fef582852820..be27b5a21b2c 100644
--- a/arch/arm/boot/dts/am335x-lxm.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-lxm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
+ * Copyright (C) 2014 NovaTech LLC - https://www.novatechweb.com
  */
 /dts-v1/;
 
@@ -41,7 +41,7 @@
 };
 
 &am33xx_pinmux {
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -52,14 +52,14 @@
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE0)
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* rmii1_int */
@@ -85,7 +85,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* rmii1_int */
@@ -111,7 +111,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -119,7 +119,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -127,7 +127,7 @@
 		>;
 	};
 
-	emmc_pins: pinmux_emmc_pins {
+	emmc_pins: emmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
@@ -142,7 +142,7 @@
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -160,11 +160,15 @@
 	serial_config1: serial_config1@20 {
 		compatible = "nxp,pca9539";
 		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
 	};
 
 	serial_config2: serial_config2@21 {
 		compatible = "nxp,pca9539";
 		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
 	};
 
 	tps: tps@2d {
@@ -173,7 +177,7 @@
 	};
 };
 
-/include/ "tps65910.dtsi"
+/include/ "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vbat>;
@@ -291,31 +295,29 @@
 	dr_mode = "host";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <3>;
+	ti,dual-emac-pvid = <3>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@5 {
 		reg = <5>;
@@ -339,7 +341,7 @@
 	pinctrl-0 = <&emmc_pins>;
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-2100-common.dtsi
index 6495a125c01f..b8730aa52ce6 100644
--- a/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-2100-common.dtsi
@@ -16,11 +16,11 @@
 
 	/* Power supply provides a fixed 3.3V @3A */
 	vmmcsd_fixed: vmmcsd-regulator {
-	      compatible = "regulator-fixed";
-	      regulator-name = "vmmcsd_fixed";
-	      regulator-min-microvolt = <3300000>;
-	      regulator-max-microvolt = <3300000>;
-	      regulator-boot-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
 	};
 
 	buttons: push_button {
@@ -31,27 +31,27 @@
 &am33xx_pinmux {
 	pinctrl-names = "default";
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	push_button_pins: pinmux_push_button {
+	push_button_pins: push-button-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* lcd_hsync.gpio2_23 */
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -59,7 +59,7 @@
 		>;
 	};
 
-	mmc1_pins_default: pinmux_mmc1_pins {
+	mmc1_pins_default: mmc1-pins {
 		pinctrl-single,pins = <
 			/* eMMC */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad12.mmc1_dat0 */
@@ -75,7 +75,7 @@
 		>;
 	};
 
-	spi0_pins: pinmux_spi0 {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -122,24 +122,24 @@
 	regulator-max-microvolt = <5000000>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
 	status = "okay";
 };
 
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
-	status = "okay";
+&cpsw_port2 {
+	ti,dual-emac-pvid = <2>;
 };
 
 &sham {
@@ -150,7 +150,7 @@
 	status = "okay";
 };
 
-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };
 
@@ -159,17 +159,15 @@
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <8>;
 	pinctrl-0 = <&mmc1_pins_default>;
-	ti,non-removable;
+	non-removable;
 	status = "okay";
 };
 
 &buttons {
 	pinctrl-names = "default";
 	pinctrl-0 = <&push_button_pins>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	button@0 {
+	button-0 {
 		label = "push_button";
 		linux,code = <0x100>;
 		gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
@@ -182,7 +180,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx25l6405d";
 		spi-max-frequency = <40000000>;
 
diff --git a/arch/arm/boot/dts/am335x-moxa-uc-2101.dts b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-2101.dts
index 5923b6e7e1cb..e986945ac1b5 100644
--- a/arch/arm/boot/dts/am335x-moxa-uc-2101.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-2101.dts
@@ -28,7 +28,7 @@
 &am33xx_pinmux {
 	pinctrl-names = "default";
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE1)	/* mii1_crs.rmii1_crs_dv */
@@ -42,7 +42,7 @@
 		>;
 	};
 
-	spi1_pins: pinmux_spi1 {
+	spi1_pins: spi1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_INPUT_PULLUP, MUX_MODE4)	 /* ecap0_in_pwm0_out.spi1_sclk */
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE4)	 /* uart1_ctsn.spi1_cs0 */
@@ -52,18 +52,17 @@
 	};
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@4 {
 		reg = <4>;
 	};
 };
 
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
 	phy-handle = <&phy0>;
 	phy-mode = "rmii";
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am335x-moxa-uc-8100-me-t.dts b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-8100-common.dtsi
index 244df9c5a537..daaa5eee0f0d 100644
--- a/arch/arm/boot/dts/am335x-moxa-uc-8100-me-t.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-8100-common.dtsi
@@ -1,17 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2017 MOXA Inc. - https://www.moxa.com/
+ * Copyright (C) 2020 MOXA Inc. - https://www.moxa.com/
  *
- * Author: SZ Lin (林上智) <sz.lin@moxa.com>
+ * Author: Johnson Chen <johnsonch.chen@moxa.com>
  */
 
-/dts-v1/;
-
 #include "am33xx.dtsi"
 
 / {
-	model = "Moxa UC-8100-ME-T";
-	compatible = "moxa,uc-8100-me-t", "ti,am33xx";
 
 	cpus {
 		cpu@0 {
@@ -19,74 +15,17 @@
 		};
 	};
 
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x20000000>; /* 512 MB */
-	};
-
 	vbat: vbat-regulator {
 		compatible = "regulator-fixed";
 	};
 
 	/* Power supply provides a fixed 3.3V @3A */
 	vmmcsd_fixed: vmmcsd-regulator {
-	      compatible = "regulator-fixed";
-	      regulator-name = "vmmcsd_fixed";
-	      regulator-min-microvolt = <3300000>;
-	      regulator-max-microvolt = <3300000>;
-	      regulator-boot-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		led1 {
-			label = "uc8100me:CEL1";
-			gpios = <&gpio_xten 8 0>;
-			default-state = "off";
-		};
-
-		led2 {
-			label = "uc8100me:CEL2";
-			gpios = <&gpio_xten 9 0>;
-			default-state = "off";
-		};
-
-		led3 {
-			label = "uc8100me:CEL3";
-			gpios = <&gpio_xten 10 0>;
-			default-state = "off";
-		};
-
-		led4 {
-			label = "uc8100me:DIA1";
-			gpios = <&gpio_xten 11 0>;
-			default-state = "off";
-		};
-		led5 {
-			label = "uc8100me:DIA2";
-			gpios = <&gpio_xten 12 0>;
-			default-state = "off";
-		};
-		led6 {
-			label = "uc8100me:DIA3";
-			gpios = <&gpio_xten 13 0>;
-			default-state = "off";
-		};
-		led7 {
-			label = "uc8100me:SD";
-			gpios = <&gpio_xten 14 0>;
-			default-state = "off";
-		};
-		led8 {
-			label = "uc8100me:USB";
-			gpios = <&gpio_xten 15 0>;
-			default-state = "off";
-		};
-		led9 {
-			label = "uc8100me:USER";
-			gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
 	};
 
 	buttons: push_button {
@@ -99,7 +38,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&minipcie_pins>;
 
-	minipcie_pins: pinmux_minipcie {
+	minipcie_pins: minipcie-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* lcd_pclk.gpio2_24 */
 			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* lcd_ac_bias_en.gpio2_25 */
@@ -107,13 +46,13 @@
 		>;
 	};
 
-	push_button_pins: pinmux_push_button {
+	push_button_pins: push-button-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* mcasp0_ahcklx.gpio3_21 */
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -121,21 +60,21 @@
 	};
 
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart0_ctsn.i2c1_sda */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart0_rtsn.i2c1_scl */
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -144,7 +83,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_INPUT, MUX_MODE6)		/* lcd_data14.uart5_ctsn */
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT_PULLDOWN, MUX_MODE6)  /* lcd_data15.uart5_rtsn */
@@ -153,7 +92,7 @@
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE1)
@@ -178,7 +117,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -186,7 +125,7 @@
 		>;
 	};
 
-	mmc0_pins_default: pinmux_mmc0_pins {
+	mmc0_pins_default: mmc0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -199,7 +138,7 @@
 		>;
 	};
 
-	mmc2_pins_default: pinmux_mmc2_pins {
+	mmc2_pins_default: mmc2-pins {
 		pinctrl-single,pins = <
 			/* eMMC */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad12.mmc2_dat0 */
@@ -215,7 +154,7 @@
 		>;
 	};
 
-	spi0_pins: pinmux_spi0 {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -254,11 +193,6 @@
 	status = "okay";
 	clock-frequency = <400000>;
 
-	tpm: tpm@20 {
-		compatible = "infineon,slb9645tt";
-		reg = <0x20>;
-	};
-
 	tps: tps@2d {
 		compatible = "ti,tps65910";
 		reg = <0x2d>;
@@ -298,8 +232,8 @@
 	dr_mode = "host";
 };
 
-#include "tps65910.dtsi"
 
+#include "../../tps65910.dtsi"
 &tps {
 	vcc1-supply = <&vbat>;
 	vcc2-supply = <&vbat>;
@@ -320,20 +254,10 @@
 		};
 
 		vdd1_reg: regulator@2 {
-			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
-			regulator-name = "vdd_mpu";
-			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1378000>;
-			regulator-boot-on;
 			regulator-always-on;
 		};
 
 		vdd2_reg: regulator@3 {
-			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
-			regulator-name = "vdd_core";
-			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1150000>;
-			regulator-boot-on;
 			regulator-always-on;
 		};
 
@@ -386,17 +310,15 @@
 	regulator-max-microvolt = <5000000>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@4 {
 		reg = <4>;
@@ -407,18 +329,16 @@
 	};
 };
 
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
-	status = "okay";
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &sham {
@@ -429,7 +349,7 @@
 	status = "okay";
 };
 
-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };
 
@@ -458,10 +378,8 @@
 &buttons {
 	pinctrl-names = "default";
 	pinctrl-0 = <&push_button_pins>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	button@0 {
+	button-0 {
 		label = "push_button";
 		linux,code = <0x100>;
 		gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
@@ -474,7 +392,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx25l6405d";
 		spi-max-frequency = <40000000>;
 
diff --git a/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-8100-me-t.dts b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-8100-me-t.dts
new file mode 100644
index 000000000000..0c7949d21bd9
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-moxa-uc-8100-me-t.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2017 MOXA Inc. - https://www.moxa.com/
+ *
+ * Author: SZ Lin (林上智) <sz.lin@moxa.com>
+ */
+/dts-v1/;
+
+#include "am335x-moxa-uc-8100-common.dtsi"
+
+/ {
+	model = "Moxa UC-8100-ME-T";
+	compatible = "moxa,uc-8100-me-t", "ti,am33xx";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			label = "uc8100me:CEL1";
+			gpios = <&gpio_xten 8 0>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "uc8100me:CEL2";
+			gpios = <&gpio_xten 9 0>;
+			default-state = "off";
+		};
+
+		led3 {
+			label = "uc8100me:CEL3";
+			gpios = <&gpio_xten 10 0>;
+			default-state = "off";
+		};
+
+		led4 {
+			label = "uc8100me:DIA1";
+			gpios = <&gpio_xten 11 0>;
+			default-state = "off";
+		};
+		led5 {
+			label = "uc8100me:DIA2";
+			gpios = <&gpio_xten 12 0>;
+			default-state = "off";
+		};
+		led6 {
+			label = "uc8100me:DIA3";
+			gpios = <&gpio_xten 13 0>;
+			default-state = "off";
+		};
+		led7 {
+			label = "uc8100me:SD";
+			gpios = <&gpio_xten 14 0>;
+			default-state = "off";
+		};
+		led8 {
+			label = "uc8100me:USB";
+			gpios = <&gpio_xten 15 0>;
+			default-state = "off";
+		};
+		led9 {
+			label = "uc8100me:USER";
+			gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&i2c0 {
+	tpm: tpm@20 {
+		compatible = "infineon,slb9645tt";
+		reg = <0x20>;
+	};
+};
+
+&tps {
+	regulators {
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1378000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+};
+
diff --git a/arch/arm/boot/dts/ti/omap/am335x-myirtech-myc.dtsi b/arch/arm/boot/dts/ti/omap/am335x-myirtech-myc.dtsi
new file mode 100644
index 000000000000..584599269217
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-myirtech-myc.dtsi
@@ -0,0 +1,277 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* SPDX-FileCopyrightText: Alexander Shiyan, <shc_work@mail.ru> */
+
+/* Based on code by myc_c335x.dts, MYiRtech.com */
+/* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "MYIR MYC-AM335X";
+	compatible = "myir,myc-am335x", "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd_core>;
+			voltage-tolerance = <2>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	clk32k: clk32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+
+		#clock-cells = <0>;
+	};
+
+	vdd_mod: vdd_mod_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mod";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_core: vdd_core_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-core";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mod>;
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_mod_pins>;
+
+		led_mod: led_mod {
+			label = "module:user";
+			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+};
+
+&mac_sw {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&eth_slave1_pins_default>;
+	pinctrl-1 = <&eth_slave1_pins_sleep>;
+	status = "okay";
+};
+
+&cpsw_port1 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&davinci_mdio_sw {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mdio_pins_default>;
+	pinctrl-1 = <&mdio_pins_sleep>;
+
+	phy0: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&nand_pins_default>;
+	pinctrl-1 = <&nand_pins_sleep>;
+	ranges = <0 0 0x8000000 0x1000000>;
+	status = "okay";
+
+	nand0: nand@0,0 {
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>;
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE_NONE>;
+		nand-bus-width = <8>;
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-pin = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		ti,elm-id = <&elm>;
+		ti,nand-ecc-opt = "bch8";
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default", "gpio", "sleep";
+	pinctrl-0 = <&i2c0_pins_default>;
+	pinctrl-1 = <&i2c0_pins_gpio>;
+	pinctrl-2 = <&i2c0_pins_sleep>;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&vdd_mod>;
+	};
+};
+
+&rtc {
+	clocks = <&clk32k>;
+	clock-names = "ext-clk";
+	system-power-controller;
+};
+
+&am33xx_pinmux {
+	mdio_pins_default: mdio-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)	/* mdio_data */
+			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)			/* mdio_clk */
+		>;
+	};
+
+	mdio_pins_sleep: mdio-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	eth_slave1_pins_default: eth-slave1-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_tctl */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rctl */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td3 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td2 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td0 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_tclk */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rclk */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd3 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd2 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd0 */
+		>;
+	};
+
+	eth_slave1_pins_sleep: eth-slave1-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	i2c0_pins_default: i2c0-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE0)	/* I2C0_SDA */
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE0)	/* I2C0_SCL */
+		>;
+	};
+
+	i2c0_pins_gpio: i2c0-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE7)			/* gpio3[5] */
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE7)			/* gpio3[6] */
+		>;
+	};
+
+	i2c0_pins_sleep: i2c0-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	led_mod_pins: led-mod-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE7)		/* gpio3[18] */
+		>;
+	};
+
+	nand_pins_default: nand-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad4 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad5 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad6 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad7 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_wait0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)		/* gpio0[31] */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0)			/* gpmc_csn0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0)			/* gpmc_advn_ale */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_OUTPUT, MUX_MODE0)			/* gpmc_oen_ren */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_OUTPUT, MUX_MODE0)			/* gpmc_wen */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN0_CLE, PIN_OUTPUT, MUX_MODE0)			/* gpmc_be0n_cle */
+		>;
+	};
+
+	nand_pins_sleep: nand-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN0_CLE, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/am335x-myirtech-myd.dts b/arch/arm/boot/dts/ti/omap/am335x-myirtech-myd.dts
new file mode 100644
index 000000000000..d3bba79b9358
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-myirtech-myd.dts
@@ -0,0 +1,549 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* SPDX-FileCopyrightText: Alexander Shiyan, <shc_work@mail.ru> */
+/* Based on code by myd_c335x.dts, MYiRtech.com */
+/* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */
+
+/dts-v1/;
+
+#include "am335x-myirtech-myc.dtsi"
+
+#include <dt-bindings/display/tda998x.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MYIR MYD-AM335X";
+	compatible = "myir,myd-am335x", "myir,myc-am335x", "ti,am33xx";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	clk12m: clk12m {
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+
+		#clock-cells = <0>;
+	};
+
+	gpio_buttons: gpio_buttons {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_buttons_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button1: button@0 {
+			reg = <0>;
+			label = "button1";
+			linux,code = <BTN_1>;
+			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button2: button@1 {
+			reg = <1>;
+			label = "button2";
+			linux,code = <BTN_2>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&master_codec>;
+		simple-audio-card,frame-master = <&master_codec>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+		};
+
+		master_codec: simple-audio-card,codec@1 {
+			sound-dai = <&sgtl5000>;
+		};
+
+		simple-audio-card,codec@2 {
+			sound-dai = <&tda9988>;
+		};
+	};
+
+	vdd_5v0: vdd_5v0_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3: vdd_3v3_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_5v0>;
+	};
+};
+
+&cpsw_port2 {
+	status = "okay";
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <2>;
+};
+
+&davinci_mdio_sw {
+	phy1: ethernet-phy@6 {
+		reg = <6>;
+		eee-broken-1000t;
+	};
+};
+
+&mac_sw {
+	pinctrl-0 = <&eth_slave1_pins_default>, <&eth_slave2_pins_default>;
+	pinctrl-1 = <&eth_slave1_pins_sleep>, <&eth_slave2_pins_sleep>;
+	slaves = <2>;
+};
+
+&dcan0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcan0_pins_default>;
+	pinctrl-1 = <&dcan0_pins_sleep>;
+	status = "okay";
+};
+
+&dcan1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcan1_pins_default>;
+	pinctrl-1 = <&dcan1_pins_sleep>;
+	status = "okay";
+};
+
+&ehrpwm0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ehrpwm0_pins_default>;
+	pinctrl-1 = <&ehrpwm0_pins_sleep>;
+	status = "okay";
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "gpio", "sleep";
+	pinctrl-0 = <&i2c1_pins_default>;
+	pinctrl-1 = <&i2c1_pins_gpio>;
+	pinctrl-2 = <&i2c1_pins_sleep>;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	sgtl5000: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg =<0xa>;
+		clocks = <&clk12m>;
+		micbias-resistor-k-ohms = <4>;
+		micbias-voltage-m-volts = <2250>;
+		VDDA-supply = <&vdd_3v3>;
+		VDDIO-supply = <&vdd_3v3>;
+
+		#sound-dai-cells = <0>;
+	};
+
+	tda9988: tda9988@70 {
+		compatible = "nxp,tda998x";
+		reg =<0x70>;
+		audio-ports = <TDA998x_I2S 1>;
+
+		#sound-dai-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_0: endpoint {
+					remote-endpoint = <&lcdc_0>;
+				};
+			};
+		};
+	};
+};
+
+&lcdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&lcdc_pins_default>;
+	pinctrl-1 = <&lcdc_pins_sleep>;
+	blue-and-red-wiring = "straight";
+	status = "okay";
+
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <&hdmi_0>;
+		};
+	};
+};
+
+&leds {
+	pinctrl-0 = <&led_mod_pins &leds_pins>;
+
+	led1: led1 {
+		label = "base:user1";
+		gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		color = <LED_COLOR_ID_GREEN>;
+		default-state = "off";
+	};
+
+	led2: led2 {
+		label = "base:user2";
+		gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+		color = <LED_COLOR_ID_GREEN>;
+		default-state = "off";
+	};
+};
+
+&mcasp0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mcasp0_pins_default>;
+	pinctrl-1 = <&mcasp0_pins_sleep>;
+	op-mode = <0>;
+	tdm-slots = <2>;
+	serial-dir = <0 1 2 0>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+	status = "okay";
+
+	#sound-dai-cells = <0>;
+};
+
+&mmc1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_sleep>;
+	cd-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_3v3>;
+	status = "okay";
+};
+
+&nand0 {
+	nand_parts: partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "MLO";
+			reg = <0x00000 0x20000>;
+		};
+
+		partition@80000 {
+			label = "boot";
+			reg = <0x80000 0x100000>;
+		};
+	};
+};
+
+&tscadc {
+	status = "okay";
+
+	adc: adc {
+		ti,adc-channels = <0 1 2 3 4 5 6>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&uart1_pins_default>;
+	pinctrl-1 = <&uart1_pins_sleep>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&uart2_pins_default>;
+	pinctrl-1 = <&uart2_pins_sleep>;
+	status = "okay";
+};
+
+&usb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb_pins>;
+};
+
+&usb0 {
+	dr_mode = "otg";
+};
+
+&usb0_phy {
+	vcc-supply = <&vdd_5v0>;
+};
+
+&usb1 {
+	dr_mode = "host";
+};
+
+&usb1_phy {
+	vcc-supply = <&vdd_5v0>;
+};
+
+&vdd_mod {
+	vin-supply = <&vdd_3v3>;
+};
+
+&am33xx_pinmux {
+	dcan0_pins_default: dcan0-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE2)			/* dcan0_tx_mux2 */
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT, MUX_MODE2)			/* dcan0_rx_mux2 */
+		>;
+	};
+
+	dcan0_pins_sleep: dcan0-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	dcan1_pins_default: dcan1-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)			/* dcan1_tx_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)			/* dcan1_rx_mux0 */
+		>;
+	};
+
+	dcan1_pins_sleep: dcan1-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	ehrpwm0_pins_default: ehrpwm0-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_OUTPUT, MUX_MODE3)			/* ehrpwm0A_mux1 */
+		>;
+	};
+
+	ehrpwm0_pins_sleep: ehrpwm0-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	eth_slave2_pins_default: eth-slave2-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_tctl */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rctl */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_tclk */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rclk */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rd3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rd2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE2		/* rgmii2_rd1 */)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE2		/* rgmii2_rd0 */)
+		>;
+	};
+
+	eth_slave2_pins_sleep: eth-slave2-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	gpio_buttons_pins: gpio-buttons-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLDOWN, MUX_MODE7)		/* gpio3[0] */
+			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT, MUX_MODE7)			/* gpio0[29] */
+		>;
+	};
+
+	i2c1_pins_default: i2c1-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE2)	/* I2C1_SDA_mux3 */
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE2)	/* I2C1_SCL_mux3 */
+		>;
+	};
+
+	i2c1_pins_gpio: i2c1-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT, MUX_MODE7)			/* gpio0[4] */
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT, MUX_MODE7)			/* gpio0[5] */
+		>;
+	};
+
+	i2c1_pins_sleep: i2c1-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	lcdc_pins_default: lcdc-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)			/* lcd_data0 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)			/* lcd_data1 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)			/* lcd_data2 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)			/* lcd_data3 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)			/* lcd_data4 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)			/* lcd_data5 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)			/* lcd_data6 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)			/* lcd_data7 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)			/* lcd_data8 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)			/* lcd_data9 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)			/* lcd_data10 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)			/* lcd_data11 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)			/* lcd_data12 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)			/* lcd_data13 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)			/* lcd_data14 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)			/* lcd_data15 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT, MUX_MODE0)			/* lcd_vsync */
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT, MUX_MODE0)			/* lcd_hsync */
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT, MUX_MODE0)			/* lcd_pclk */
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT, MUX_MODE0)		/* lcd_ac_bias_en */
+		>;
+	};
+
+	lcdc_pins_sleep: lcdc-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	leds_pins: leds-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_OUTPUT, MUX_MODE7)			/* gpio0[27] */
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE7)			/* gpio0[3] */
+		>;
+	};
+
+	mcasp0_pins_default: mcasp0-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)		/* mcasp0_aclkx_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE0)		/* mcasp0_fsx_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* mcasp0_axr2_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_INPUT_PULLDOWN, MUX_MODE0)		/* mcasp0_axr1_mux0 */
+		>;
+	};
+
+	mcasp0_pins_sleep: mcasp0-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	mmc1_pins_default: mmc1-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat3 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat2 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat1 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat0 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_clk */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_cmd */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE7)		/* gpio3[21] */
+		>;
+	};
+
+	mmc1_pins_sleep: mmc1-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	uart0_pins: uart0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)		/* uart0_rxd */
+			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* uart0_txd */
+		>;
+	};
+
+	uart1_pins_default: uart1-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)		/* uart1_rxd */
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* uart1_txd */
+		>;
+	};
+
+	uart1_pins_sleep: uart1-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	uart2_pins_default: uart2-default-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT, MUX_MODE6)			/* uart2_rxd_mux1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_OUTPUT, MUX_MODE6)			/* uart2_txd_mux1 */
+		>;
+	};
+
+	uart2_pins_sleep: uart2-sleep-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	usb_pins: usb-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_USB0_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* USB0_DRVVBUS */
+			AM33XX_PADCONF(AM335X_PIN_USB1_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* USB1_DRVVBUS */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/ti/omap/am335x-nano.dts
index 0946fbf1b1fb..a475c0d91306 100644
--- a/arch/arm/boot/dts/am335x-nano.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-nano.dts
@@ -36,13 +36,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&misc_pins>;
 
-	misc_pins: misc_pins {
+	misc_pins: misc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_OUTPUT, MUX_MODE7)	/* spi0_cs0.gpio0_5 */
 		>;
 	};
 
-	gpmc_pins: gpmc_pins {
+	gpmc_pins: gpmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -86,21 +86,21 @@
 		>;
 	};
 
-	i2c0_pins: i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart0_pins: uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT, MUX_MODE7)
@@ -109,7 +109,7 @@
 		>;
 	};
 
-	uart2_pins: uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_INPUT_PULLUP, MUX_MODE7)	/* lcd_data8.gpio2[14] */
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE7)		/* lcd_data9.gpio2[15] */
@@ -118,32 +118,32 @@
 		>;
 	};
 
-	uart3_pins: uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_INPUT_PULLUP, MUX_MODE6)	/* lcd_data10.uart3_ctsn */
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE6)		/* lcd_data11.uart3_rtsn */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_INPUT_PULLUP, MUX_MODE7)	/* lcd_data10.gpio2[16] */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE7)		/* lcd_data11.gpio2[17] */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE1)		/* spi0_cs1.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_OUTPUT, MUX_MODE1)		/* ecap0_in_pwm0_out.uart3_txd */
 		>;
 	};
 
-	uart4_pins: uart4_pins {
+	uart4_pins: uart4-pins {
 		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_INPUT_PULLUP, MUX_MODE6)	/* lcd_data12.uart4_ctsn */
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE6)		/* lcd_data13.uart4_rtsn */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_INPUT_PULLUP, MUX_MODE7)	/* lcd_data12.gpio0[8] */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE7)		/* lcd_data13.gpio0[9] */
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT, MUX_MODE1)		/* uart0_ctsn.uart4_rxd */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_OUTPUT, MUX_MODE1)		/* uart0_rtsn.uart4_txd */
 		>;
 	};
 
-	uart5_pins: uart5_pins {
+	uart5_pins: uart5-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_INPUT, MUX_MODE4)		/* lcd_data14.uart5_rxd */
 			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT, MUX_MODE3)		/* rmiii1_refclk.uart5_txd */
 		>;
 	};
 
-	mmc1_pins: mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -187,12 +187,22 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
+	rts-gpio = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+	rs485-rts-active-high;
+	rs485-rx-during-tx;
+	rs485-rts-delay = <1 1>;
+	linux,rs485-enabled-at-boot-time;
 	status = "okay";
 };
 
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins>;
+	rts-gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+	rs485-rts-active-high;
+	rs485-rx-during-tx;
+	rs485-rts-delay = <1 1>;
+	linux,rs485-enabled-at-boot-time;
 	status = "okay";
 };
 
@@ -220,6 +230,11 @@
 		reg = <0x24>;
 	};
 
+	temperature-sensor@48 {
+		compatible = "lm75";
+		reg = <0x48>;
+	};
+
 	eeprom@53 {
 		compatible = "microchip,24c02", "atmel,24c02";
 		reg = <0x53>;
@@ -238,7 +253,6 @@
 
 &gpmc {
 	compatible = "ti,am3352-gpmc";
-	ti,hwmods = "gpmc";
 	status = "okay";
 	gpmc,num-waitpins = <2>;
 	pinctrl-names = "default";
@@ -370,12 +384,11 @@
 	};
 };
 
-&mac {
-	dual_emac;
+&mac_sw {
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
@@ -387,16 +400,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &mmc1 {
@@ -405,11 +418,16 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	bus-width = <4>;
-	cd-gpios = <&gpio3 8 0>;
-	wp-gpios = <&gpio3 18 0>;
+	cd-debounce-delay-ms = <5>;
+	cd-gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
+};
+
+&usb0 {
+	dr_mode = "host";
 };
 
-#include "tps65217.dtsi"
+#include "../../tps65217.dtsi"
 
 &tps {
 	regulators {
diff --git a/arch/arm/boot/dts/ti/omap/am335x-netcan-plus-1xx.dts b/arch/arm/boot/dts/ti/omap/am335x-netcan-plus-1xx.dts
new file mode 100644
index 000000000000..f7fad48e36ed
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-netcan-plus-1xx.dts
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/*
+ * VScom OnRISC
+ * http://www.vscom.de
+ */
+
+/dts-v1/;
+
+#include "am335x-baltos.dtsi"
+#include "am335x-baltos-leds.dtsi"
+
+/ {
+	model = "NetCAN";
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		compatible = "gpio-leds";
+
+		led@1 {
+			label = "can_data";
+			linux,default-trigger = "netdev";
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@2 {
+			label = "can_error";
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	user_leds_s0: user-leds-s0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* CAN Data LED */
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* CAN Error LED */
+		>;
+	};
+
+	dcan1_pins: dcan1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)	/* CAN TX */
+			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)	/* CAN RX */
+		>;
+	};
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&davinci_mdio_sw {
+	phy0: ethernet-phy@0 {
+		reg = <1>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rmii";
+	ti,dual-emac-pvid = <1>;
+	phy-handle = <&phy0>;
+};
+
+&cpsw_port2 {
+	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <2>;
+	phy-handle = <&phy1>;
+};
+
+&dcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_pins>;
+
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"NC",
+		"NC",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"can_data",
+		"can_error",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"NC",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"NC",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"DCAN1_TX",
+		"DCAN1_RX",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"ModeA0",
+		"ModeA1",
+		"ModeA2",
+		"ModeA3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-netcom-plus-2xx.dts b/arch/arm/boot/dts/ti/omap/am335x-netcom-plus-2xx.dts
index 9a6cd8ef821f..76751a324ad7 100644
--- a/arch/arm/boot/dts/am335x-netcom-plus-2xx.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-netcom-plus-2xx.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -18,7 +18,7 @@
 };
 
 &am33xx_pinmux {
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)			/* RX */
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)			/* TX */
@@ -31,7 +31,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE1)		/* RX */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE1)      		/* TX */
@@ -76,20 +76,164 @@
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@0 {
 		reg = <1>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	phy-handle = <&phy0>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"UART2_RX",
+		"UART2_TX",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"NC",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"NC",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"UART2_DTR",
+		"UART2_DSR",
+		"UART2_DCD",
+		"UART2_RI",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"NC",
+		"NC",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART2_CTSN",
+		"UART2_RTSN",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"ModeA0",
+		"ModeA1",
+		"ModeA2",
+		"ModeA3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/ti/omap/am335x-netcom-plus-8xx.dts b/arch/arm/boot/dts/ti/omap/am335x-netcom-plus-8xx.dts
new file mode 100644
index 000000000000..5a9fcec040fa
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-netcom-plus-8xx.dts
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/*
+ * VScom OnRISC
+ * http://www.vscom.de
+ */
+
+/dts-v1/;
+
+#include "am335x-baltos.dtsi"
+
+/ {
+	model = "NetCom Plus";
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dip_switches>;
+
+	dip_switches: dip-switches-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	tca6416_pins: tca6416-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+	};
+
+	i2c2_pins: i2c2-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE3)
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE3)
+		>;
+	};
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&i2c1 {
+	tca6416a: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tca6416_pins>;
+		gpio-line-names = "GP_IN0", "GP_IN1", "GP_IN2", "GP_IN3",
+				  "GP_IN4", "GP_IN5", "GP_IN6", "GP_IN7",
+				  "GP_OUT0", "GP_OUT1", "GP_OUT2", "GP_OUT3",
+				  "GP_OUT4", "GP_OUT5", "GP_OUT6", "GP_OUT7";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tca6416b: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "CH1_M0", "CH1_M1", "CH1_M2", "CH1_M3",
+				  "CH2_M0", "CH2_M1", "CH2_M2", "CH2_M3",
+				  "CH3_M0", "CH3_M1", "CH3_M2", "CH3_M3",
+				  "CH4_M0", "CH4_M1", "CH4_M2", "CH4_M3";
+	};
+
+	tca6416c: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "CH5_M0", "CH5_M1", "CH5_M2", "CH5_M3",
+				  "CH6_M0", "CH6_M1", "CH6_M2", "CH6_M3",
+				  "CH7_M0", "CH7_M1", "CH7_M2", "CH7_M3",
+				  "CH8_M0", "CH8_M1", "CH8_M2", "CH8_M3";
+	};
+};
+
+&davinci_mdio_sw {
+	phy0: ethernet-phy@0 {
+		reg = <1>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rmii";
+	ti,dual-emac-pvid = <1>;
+	phy-handle = <&phy0>;
+};
+
+&cpsw_port2 {
+	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <2>;
+	phy-handle = <&phy1>;
+};
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"NC",
+		"NC",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"I2C2_SDA",
+		"I2C2_SCL",
+		"NC",
+		"NC",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"NC",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"NC",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"SW2_0_alt",
+		"SW2_1_alt",
+		"SW2_2_alt",
+		"SW2_3_alt",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"NC",
+		"NC",
+		"NC",
+		"3G_PWR_EN",
+		"NC",
+		"NC",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts b/arch/arm/boot/dts/ti/omap/am335x-osd3358-sm-red.dts
index 1d2902083483..d28d39728847 100644
--- a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-osd3358-sm-red.dts
@@ -1,5 +1,5 @@
 //SPDX-License-Identifier: GPL-2.0
-/* Copyright (C) 2018 Octavo Systems LLC - http://www.octavosystems.com/
+/* Copyright (C) 2018 Octavo Systems LLC - https://www.octavosystems.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -25,10 +25,6 @@
 	regulator-always-on;
 };
 
-&mmc1 {
-	vmmc-supply = <&vmmcsd_fixed>;
-};
-
 &mmc2 {
 	vmmc-supply = <&vmmcsd_fixed>;
 	pinctrl-names = "default";
@@ -37,68 +33,6 @@
 	status = "okay";
 };
 
-&am33xx_pinmux {
-	nxp_hdmi_bonelt_pins: nxp-hdmi-bonelt-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-		>;
-	};
-
-	nxp_hdmi_bonelt_off_pins: nxp-hdmi-bonelt-off-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
-		>;
-	};
-
-	mcasp0_pins: mcasp0-pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a11.GPIO1_27 */
-		>;
-	};
-
-	flash_enable: flash-enable {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE7) 	/* rmii1_ref_clk.gpio0_29 */
-		>;
-	};
-
-	imu_interrupt: imu-interrupt {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7) 		/* mii1_rx_er.gpio3_2 */
-		>;
-	};
-
-	ethernet_interrupt: ethernet-interrupt{
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLDOWN, MUX_MODE7) 		/* mii1_col.gpio3_0 */
-		>;
-	};
-};
-
 &lcdc {
 	status = "okay";
 
@@ -107,7 +41,7 @@
 	 * below to "crossed" and uncomment the video-ports -property
 	 * in tda19988 node.
 	 * AM335x errata for wiring:
-	 * http://www.ti.com/lit/er/sprz360i/sprz360i.pdf
+	 * https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
 	 */
 
 	blue-and-red-wiring = "straight";
@@ -150,7 +84,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ax8975@c {
-				compatible = "ak,ak8975";
+				compatible = "asahi-kasei,ak8975";
 				reg = <0x0c>;
 			};
 		};
@@ -167,10 +101,6 @@
 	};
 };
 
-&rtc {
-	system-power-controller;
-};
-
 &mcasp0 {
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
@@ -267,7 +197,67 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&clkout2_pin>;
 
-	user_leds_s0: user-leds-s0 {
+	nxp_hdmi_bonelt_pins: nxp-hdmi-bonelt-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+		>;
+	};
+
+	nxp_hdmi_bonelt_off_pins: nxp-hdmi-bonelt-off-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
+		>;
+	};
+
+	mcasp0_pins: mcasp0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+		>;
+	};
+
+	flash_enable: flash-enable-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* rmii1_ref_clk.gpio0_29 */
+		>;
+	};
+
+	imu_interrupt: imu-interrupt-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* mii1_rx_er.gpio3_2 */
+		>;
+	};
+
+	ethernet_interrupt: ethernet-interrupt-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* mii1_col.gpio3_0 */
+		>;
+	};
+
+	user_leds_s0: user-leds-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_a6.gpio1_22 */
@@ -290,13 +280,13 @@
 		>;
 	};
 
-	clkout2_pin: pinmux-clkout2-pin {
+	clkout2_pin: pinmux-clkout2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3)	/* xdma_event_intr1.clkout2 */
 		>;
 	};
 
-	cpsw_default: cpsw-default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
@@ -314,7 +304,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw-sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -332,7 +322,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci-mdio-default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -340,7 +330,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci-mdio-sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -401,24 +391,27 @@
 	clock-frequency = <100000>;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@4 {
 		reg = <4>;
@@ -427,6 +420,7 @@
 
 &mmc1 {
 	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <0x4>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
@@ -434,6 +428,7 @@
 };
 
 &rtc {
+	system-power-controller;
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
 };
diff --git a/arch/arm/boot/dts/am335x-osd335x-common.dtsi b/arch/arm/boot/dts/ti/omap/am335x-osd335x-common.dtsi
index a8b6842489f7..93a3af83feac 100644
--- a/arch/arm/boot/dts/am335x-osd335x-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-osd335x-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  *
  * Author: Robert Nelson <robertcnelson@gmail.com>
  */
@@ -28,7 +28,8 @@
 	* the HW OPP table, the silicon looks like it is Revision 1.0 (ie the
 	* EFUSE_SMA register reads as all zeros).
 	*/
-	oppnitro-1000000000 {
+	opp-1000000000 {
+		/* OPP Nitro */
 		opp-supported-hw = <0x06 0x0100>;
 	};
 };
@@ -54,7 +55,7 @@
 	};
 };
 
-/include/ "tps65217.dtsi"
+/include/ "../../tps65217.dtsi"
 
 &tps {
 	interrupts = <7>; /* NMI */
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/ti/omap/am335x-pcm-953.dtsi
index 6c547c83e5dd..75efe1cf1dd2 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-pcm-953.dtsi
@@ -12,56 +12,52 @@
 	compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx";
 
 	/* Power */
-	regulators {
-		vcc3v3: fixedregulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "vcc3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-boot-on;
-		};
+	vcc3v3: fixedregulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
 
-		vcc1v8: fixedregulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "vcc1v8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-boot-on;
-		};
+	vcc1v8: fixedregulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
 	};
 
 	/* User IO */
-	user_leds: user_leds {
+	user_leds: user-leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_leds_pins>;
 
 		user-led0 {
 			gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
 			default-state = "on";
 		};
 
 		user-led1 {
 			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "gpio";
 			default-state = "on";
 		};
 	};
 
-	user_buttons: user_buttons {
+	user_buttons: user-buttons {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_buttons_pins>;
 
-		button@0 {
+		button-0 {
 			label = "home";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
 			wakeup-source;
 		};
 
-		button@1 {
+		button-1 {
 			label = "menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
@@ -72,14 +68,14 @@
 };
 
 &am33xx_pinmux {
-	user_buttons_pins: pinmux_user_buttons {
+	user_buttons_pins: pinmux-user-buttons-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_EMU0, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* emu0.gpio3_7 */
 			AM33XX_PADCONF(AM335X_PIN_EMU1, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* emu1.gpio3_8 */
 		>;
 	};
 
-	user_leds_pins: pinmux_user_leds {
+	user_leds_pins: pinmux-user-leds-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_csn1.gpio1_30 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_csn2.gpio1_31 */
@@ -89,7 +85,7 @@
 
 /* CAN */
 &am33xx_pinmux {
-	dcan1_pins: pinmux_dcan1 {
+	dcan1_pins: pinmux-dcan1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT_PULLUP, MUX_MODE2)	/* uart1_rxd.dcan1_tx_mux2 */
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT_PULLUP, MUX_MODE2)	/* uart1_txd.dcan1_rx_mux2 */
@@ -105,7 +101,7 @@
 
 /* Ethernet */
 &am33xx_pinmux {
-	ethernet1_pins: pinmux_ethernet1 {
+	ethernet1_pins: ethernet1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* gpmc_a1.rgmii2_rctl */
@@ -123,24 +119,22 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@2 {
 		reg = <2>;
 	};
 };
 
-&mac {
-	slaves = <2>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
-	dual_emac;
 };
 
 /* Misc */
@@ -148,7 +142,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&cb_gpio_pins>;
 
-	cb_gpio_pins: pinmux_cb_gpio {
+	cb_gpio_pins: pinmux-cb-gpio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* uart0_ctsn.gpio1_8 */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* uart0_rtsn.gpio1_9 */
@@ -158,7 +152,7 @@
 
 /* MMC */
 &am33xx_pinmux {
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: pinmux-mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -182,14 +176,14 @@
 
 /* UARTs */
 &am33xx_pinmux {
-	uart0_pins: pinmux_uart0 {
+	uart0_pins: pinmux-uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: pinmux_uart1 {
+	uart1_pins: pinmux-uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -198,14 +192,14 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2 {
+	uart2_pins: pinmux-uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_tx_clk.uart2_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* mii1_rx_clk.uart2_txd */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3 {
+	uart3_pins: pinmux-uart3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_rxd3.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* mii1_rxd2.uart3_txd */
diff --git a/arch/arm/boot/dts/am335x-pdu001.dts b/arch/arm/boot/dts/ti/omap/am335x-pdu001.dts
index e4dcfa087a1b..3c9444e98c14 100644
--- a/arch/arm/boot/dts/am335x-pdu001.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-pdu001.dts
@@ -5,7 +5,7 @@
  *
  * Copyright (C) 2018 EETS GmbH - http://www.eets.ch/
  *
- * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ * Copyright (C) 2011, Texas Instruments, Incorporated - https://www.ti.com/
  *
  * SPDX-License-Identifier:  GPL-2.0+
  */
@@ -90,28 +90,28 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&clkout2_pin>;
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE2)	/* spi0_d1.i2c1_sda */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE2)	/* spi0_cs0.i2c1_scl */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE2)	/* spi0_clk.i2c2_sda */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE2)	/* spi0_d0.i2c2_scl */
 		>;
 	};
 
-	spi1_pins: pinmux_spi1_pins {
+	spi1_pins: spi1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT, MUX_MODE3)		/* mcasp0_aclkx.spi1_sclk */
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT, MUX_MODE3)		/* mcasp0_fsx.spi1_d0 */
@@ -120,7 +120,7 @@
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_OUTPUT, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -128,27 +128,27 @@
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT_PULLUP, MUX_MODE1)	/* spi0_cs1.uart3_rxd */
 			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* ecap0_in_pwm0_out.uart3_txd */
 		>;
 	};
 
-	clkout2_pin: pinmux_clkout2_pin {
+	clkout2_pin: clkout2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3)	/* xdma_event_intr1.clkout2 */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Port 1 (emac0) */
 			AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT, MUX_MODE0)
@@ -186,14 +186,14 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		/* eMMC */
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -205,7 +205,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		/* SD cardcage */
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* gpmc_ad3.mmc1_dat3 */
@@ -219,7 +219,7 @@
 		>;
 	};
 
-	lcd_pins_s0: lcd_pins_s0 {
+	lcd_pins_s0: lcd-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
@@ -244,7 +244,7 @@
 		>;
 	};
 
-	dcan0_pins: pinmux_dcan0_pins {
+	dcan0_pins: dcan0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE2)		/* uart1_ctsn.d_can0_tx */
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* uart1_rtsn.d_can0_rx */
@@ -353,7 +353,7 @@
 		};
 	};
 
-	mcp79400: mcp79400@6f {
+	mcp79400: rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
 	};
@@ -400,7 +400,7 @@
 	status = "okay";
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vbat>;
@@ -494,17 +494,15 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
-	dual_emac;			/* no switch, two distinct MACs */
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -515,16 +513,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &tscadc {
diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/ti/omap/am335x-pepper.dts
index 6d7608d9377b..d5a4a21889d1 100644
--- a/arch/arm/boot/dts/am335x-pepper.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-pepper.dts
@@ -26,7 +26,7 @@
 		compatible = "gpio-keys";
 	};
 
-	leds: user_leds {
+	leds: user-leds-pins {
 		compatible = "gpio-leds";
 	};
 
@@ -88,13 +88,13 @@
 };
 
 &am33xx_pinmux {
-	i2c0_pins: pinmux_i2c0 {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
-	i2c1_pins: pinmux_i2c1 {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLUP, MUX_MODE3)	/* mii1_crs,i2c1_sda */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLUP, MUX_MODE3)	/* mii1_rxerr,i2c1_scl */
@@ -125,7 +125,7 @@
 };
 
 &am33xx_pinmux {
-	accel_pins: pinmux_accel {
+	accel_pins: accel-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_INPUT, MUX_MODE7)   /* gpmc_wen.gpio2_4 */
 		>;
@@ -172,7 +172,7 @@
 };
 
 &am33xx_pinmux {
-	audio_pins: pinmux_audio {
+	audio_pins: audio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE0)
@@ -223,7 +223,7 @@
 };
 
 &am33xx_pinmux {
-	lcd_pins: pinmux_lcd {
+	lcd_pins: lcd-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
@@ -260,20 +260,19 @@
 };
 
 /* Ethernet */
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii";
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
-	status = "okay";
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii";
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
-	status = "okay";
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio_pins>;
 
@@ -286,15 +285,14 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet_pins>;
 };
 
-
 &am33xx_pinmux {
-	ethernet_pins: pinmux_ethernet {
+	ethernet_pins: ethernet-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLUP, MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
@@ -315,7 +313,7 @@
 		>;
 	};
 
-	mdio_pins: pinmux_mdio {
+	mdio_pins: mdio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
@@ -341,7 +339,7 @@
 	pinctrl-0 = <&emmc_pins>;
 	vmmc-supply = <&ldo3_reg>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 };
 
 &mmc3 {
@@ -351,7 +349,7 @@
 	pinctrl-0 = <&wireless_pins>;
 	vmmmc-supply = <&v3v3c_reg>;
 	bus-width = <4>;
-	ti,non-removable;
+	non-removable;
 	dmas = <&edma_xbar 12 0 1
 		&edma_xbar 13 0 2>;
 	dma-names = "tx", "rx";
@@ -359,7 +357,7 @@
 
 
 &am33xx_pinmux {
-	sd_pins: pinmux_sd_card {
+	sd_pins: sd-card-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -370,7 +368,7 @@
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7)		/* spi0_cs1.gpio0_6 */
 		>;
 	};
-	emmc_pins: pinmux_emmc {
+	emmc_pins: emmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn1.mmc1_clk */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn2.mmc1_cmd */
@@ -386,7 +384,7 @@
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_wpn.gpio0_31 */
 		>;
 	};
-	wireless_pins: pinmux_wireless {
+	wireless_pins: wireless-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_a1.mmc2_dat0 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_a2.mmc2_dat1 */
@@ -425,7 +423,7 @@
 	vin-supply = <&vbat>;
 };
 
-/include/ "tps65217.dtsi"
+/include/ "../../tps65217.dtsi"
 
 &tps {
 	backlight {
@@ -493,7 +491,7 @@
 };
 
 &am33xx_pinmux {
-	spi0_pins: pinmux_spi0 {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -534,13 +532,13 @@
 };
 
 &am33xx_pinmux {
-	uart0_pins: pinmux_uart0 {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
-	uart1_pins: pinmux_uart1 {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
@@ -557,15 +555,15 @@
 };
 
 &usb0 {
-        dr_mode = "host";
+	dr_mode = "host";
 };
 
 &usb1 {
-        dr_mode = "host";
+	dr_mode = "host";
 };
 
 &am33xx_pinmux {
-	usb_pins: pinmux_usb {
+	usb_pins: usb-pins {
 		pinctrl-single,pins = <
 			/* USB0 Over-Current (active low) */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT, MUX_MODE7)	/* gpmc_a9.gpio1_25 */
@@ -598,24 +596,22 @@
 &buttons {
 	pinctrl-names = "default";
 	pinctrl-0 = <&user_buttons_pins>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	button0 {
+	button-0 {
 		label = "home";
 		linux,code = <KEY_HOME>;
 		gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 		wakeup-source;
 	};
 
-	button1 {
+	button-1 {
 		label = "menu";
 		linux,code = <KEY_MENU>;
 		gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
 		wakeup-source;
 	};
 
-	buttons2 {
+	button-2 {
 		label = "power";
 		linux,code = <KEY_POWER>;
 		gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
@@ -624,14 +620,14 @@
 };
 
 &am33xx_pinmux {
-	user_leds_pins: pinmux_user_leds {
+	user_leds_pins: user-leds-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a4.gpio1_20 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
 		>;
 	};
 
-	user_buttons_pins: pinmux_user_buttons {
+	user_buttons_pins: user-buttons-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_a6.gpio1_22 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLUP, MUX_MODE7)	/* gpmc_a7.gpio1_21 */
diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts b/arch/arm/boot/dts/ti/omap/am335x-phycore-rdk.dts
index 43907d03e675..43907d03e675 100644
--- a/arch/arm/boot/dts/am335x-phycore-rdk.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-phycore-rdk.dts
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/ti/omap/am335x-phycore-som.dtsi
index 3d0672b53d77..84c15a44df6a 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-phycore-som.dtsi
@@ -14,6 +14,7 @@
 	aliases {
 		rtc0 = &i2c_rtc;
 		rtc1 = &rtc;
+		rtc2 = &tps;
 	};
 
 	cpus {
@@ -48,7 +49,7 @@
 
 /* EMMC */
 &am33xx_pinmux {
-	emmc_pins: pinmux_emmc_pins {
+	emmc_pins: pinmux-emmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn1.mmc1_clk */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn2.mmc1_cmd */
@@ -69,13 +70,13 @@
 	pinctrl-0 = <&emmc_pins>;
 	vmmc-supply = <&vmmc_reg>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 	status = "disabled";
 };
 
 /* Ethernet */
 &am33xx_pinmux {
-	ethernet0_pins: pinmux_ethernet0 {
+	ethernet0_pins: ethernet0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE1)
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE1)
@@ -88,7 +89,7 @@
 		>;
 	};
 
-	mdio_pins: pinmux_mdio {
+	mdio_pins: mdio-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -97,24 +98,26 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&phy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&davinci_mdio {
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio_pins>;
-	status = "okay";
 
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins>;
 	status = "okay";
@@ -122,7 +125,7 @@
 
 /* I2C Busses */
 &am33xx_pinmux {
-	i2c0_pins: pinmux_i2c0 {
+	i2c0_pins: pinmux-i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE0)
@@ -162,7 +165,7 @@
 
 /* NAND memory */
 &am33xx_pinmux {
-		nandflash_pins: pinmux_nandflash {
+		nandflash_pins: pinmux-nandflash-pins {
 			pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -200,7 +203,6 @@
 		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -231,7 +233,7 @@
 };
 
 /* Power */
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &tps {
 	vcc1-supply = <&vcc5v>;
@@ -314,7 +316,7 @@
 
 /* SPI Busses */
 &am33xx_pinmux {
-	spi0_pins: pinmux_spi0 {
+	spi0_pins: pinmux-spi0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLDOWN, MUX_MODE0)
@@ -329,7 +331,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	serial_flash: m25p80@0 {
+	serial_flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <48000000>;
 		reg = <0x0>;
diff --git a/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts b/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts
new file mode 100644
index 000000000000..78ce860e59b3
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-pocketbeagle.dts
@@ -0,0 +1,523 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Author: Robert Nelson <robertcnelson@gmail.com>
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-osd335x-common.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "TI AM335x PocketBeagle";
+	compatible = "ti,am335x-pocketbeagle", "ti,am335x-bone", "ti,am33xx";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&usr_leds_pins>;
+
+		compatible = "gpio-leds";
+
+		led-usr0 {
+			label = "beaglebone:green:usr0";
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led-usr1 {
+			label = "beaglebone:green:usr1";
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led-usr2 {
+			label = "beaglebone:green:usr2";
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_CPU;
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led-usr3 {
+			label = "beaglebone:green:usr3";
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+		"NC",
+		"NC",
+		"P1.08 [SPI0_CLK]",
+		"P1.10 [SPI0_MISO]",
+		"P1.12 [SPI0_MOSI]",
+		"P1.06 [SPI0_CS]",
+		"[MMC0_CD]",
+		"P2.29 [SPI1_CLK]",
+		"[SYSBOOT 12]",
+		"[SYSBOOT 13]",
+		"[SYSBOOT 14]",
+		"[SYSBOOT 15]",
+		"P1.26 [I2C2_SDA]",
+		"P1.28 [I2C2_SCL]",
+		"P2.11 [I2C1_SDA]",
+		"P2.09 [I2C1_SCL]",
+		"NC",
+		"NC",
+		"NC",
+		"P2.31 [SPI1_CS]",
+		"P1.20 [PRU0.16]",
+		"NC",
+		"NC",
+		"P2.03",
+		"NC",
+		"NC",
+		"P1.34",
+		"P2.19",
+		"NC",
+		"NC",
+		"P2.05 [UART4_RX]",
+		"P2.07 [UART4_TX]";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"P2.25 [SPI1_MOSI]",
+		"P1.32 [UART0_RX]",
+		"P1.30 [UART0_TX]",
+		"P2.24",
+		"P2.33",
+		"P2.22",
+		"P2.18 [PRU0.15i]",
+		"NC",
+		"NC",
+		"P2.01 [PWM1A]",
+		"NC",
+		"P2.10",
+		"[USR LED 0]",
+		"[USR LED 1]",
+		"[USR LED 2]",
+		"[USR LED 3]",
+		"P2.06",
+		"P2.04",
+		"P2.02",
+		"P2.08",
+		"NC",
+		"NC",
+		"NC";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"P2.20",
+		"P2.17",
+		"NC",
+		"NC",
+		"NC",
+		"[EEPROM_WP]",
+		"[SYSBOOT 0]",
+		"[SYSBOOT 1]",
+		"[SYSBOOT 2]",
+		"[SYSBOOT 3]",
+		"[SYSBOOT 4]",
+		"[SYSBOOT 5]",
+		"[SYSBOOT 6]",
+		"[SYSBOOT 7]",
+		"[SYSBOOT 8]",
+		"[SYSBOOT 9]",
+		"[SYSBOOT 10]",
+		"[SYSBOOT 11]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"P2.35 [AIN5]",
+		"P1.02 [AIN6]",
+		"P1.35 [PRU1.10]",
+		"P1.04 [PRU1.11]",
+		"[MMC0_DAT3]",
+		"[MMC0_DAT2]",
+		"[MMC0_DAT1]",
+		"[MMC0_DAT0]",
+		"[MMC0_CLK]",
+		"[MMC0_CMD]";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"[I2C0_SDA]",
+		"[I2C0_SCL]",
+		"[JTAG EMU0]",
+		"[JTAG EMU1]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"P1.03 [USB1]",
+		"P1.36 [PWM0A]",
+		"P1.33 [PRU0.1]",
+		"P2.32 [PRU0.2]",
+		"P2.30 [PRU0.3]",
+		"P1.31 [PRU0.4]",
+		"P2.34 [PRU0.5]",
+		"P2.28 [PRU0.6]",
+		"P1.29 [PRU0.7]",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
+
+&am33xx_pinmux {
+
+	compatible = "pinconf-single";
+	pinctrl-names = "default";
+
+	/* P2_03 (ZCZ ball T10) gpio0_23 0x824 PIN 9 */
+	P2_03_gpio: P2-03-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P1_34 (ZCZ ball T11) gpio0_26 0x828 PIN 10 */
+	P1_34_gpio: P1-34-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_19 (ZCZ ball U12) gpio0_27 0x82c PIN 11 */
+	P2_19_gpio: P2-19-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_24 (ZCZ ball T12) gpio1_12 0x830 PIN 12 */
+	P2_24_gpio: P2-24-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_33 (ZCZ ball R12) gpio1_13 0x834 PIN 13 */
+	P2_33_gpio: P2-33-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_22 (ZCZ ball V13) gpio1_14 0x838 PIN 14 */
+	P2_22_gpio: P2-22-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_20 (ZCZ ball T13) gpio2_00 0x888 */
+	P2_20_gpio: P2-20-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_10 (ZCZ ball R14) gpio1_20 0x850 PIN 20 */
+	P2_10_gpio: P2-10-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_06 (ZCZ ball U16) gpio1_25 0x864 PIN 25 */
+	P2_06_gpio: P2-06-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_04 (ZCZ ball T16) gpio1_26 0x868 PIN 26 */
+	P2_04_gpio: P2-04-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_02 (ZCZ ball V17) gpio1_27 0x86c PIN 27 */
+	P2_02_gpio: P2-02-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	/* P2_08 (ZCZ ball U18) gpio1_28 0x878 PIN 30 */
+	P2_08_gpio: P2-08-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x00  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x00  0x00  0x10  0x18>;
+	};
+
+	/* P2_17 (ZCZ ball V12) gpio2_1 0x88c PIN 35 */
+	P2_17_gpio: P2-17-gpio-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+		pinctrl-single,bias-pullup   =   < 0x10  0x10  0x00  0x18>;
+		pinctrl-single,bias-pulldown   = < 0x10  0x00  0x10  0x18>;
+	};
+
+	i2c2_pins: pinmux-i2c2-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* (D17) uart1_rtsn.I2C2_SCL */
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* (D18) uart1_ctsn.I2C2_SDA */
+		>;
+	};
+
+	ehrpwm0_pins: pinmux-ehrpwm0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* (A13) mcasp0_aclkx.ehrpwm0A */
+		>;
+	};
+
+	ehrpwm1_pins: pinmux-ehrpwm1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* (U14) gpmc_a2.ehrpwm1A */
+		>;
+	};
+
+	mmc0_pins: pinmux-mmc0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7)		/* (C15) spi0_cs1.gpio0[6] */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
+		>;
+	};
+
+	spi0_pins: pinmux-spi0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0)
+		>;
+	};
+
+	spi1_pins: pinmux-spi1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_INPUT_PULLUP, MUX_MODE4)	/* (C18) eCAP0_in_PWM0_out.spi1_sclk */
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE4)	/* (E18) uart0_ctsn.spi1_d0 */
+			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE4)	/* (E17) uart0_rtsn.spi1_d1 */
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE4)	/* (A15) xdma_event_intr0.spi1_cs1 */
+		>;
+	};
+
+	usr_leds_pins: pinmux-usr-leds-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7)		/* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT, MUX_MODE7)		/* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_OUTPUT, MUX_MODE7)		/* (T15) gpmc_a7.gpio1[23] - USR_LED_2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_OUTPUT, MUX_MODE7)		/* (V16) gpmc_a8.gpio1[24] - USR_LED_3 */
+		>;
+	};
+
+	uart0_pins: pinmux-uart0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+		>;
+	};
+
+	uart4_pins: pinmux-uart4-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)	/* (T17) gpmc_wait0.uart4_rxd */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* (U17) gpmc_wpn.uart4_txd */
+		>;
+	};
+
+	pru0_pins: pinmux-pru0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE5)/* (D14) xdma_event_intr1.pr1_pru0_pru_r31_16 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE5)/* (A14) mcasp0_ahclkx.pr1_pru0_pru_r30_7 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (B12) mcasp0_acklr.pr1_pru0_pru_r30_4 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (B13) mcasp0_fsx.pr1_pru0_pru_r30_1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE6)	/* (U13) gpmc_ad15.pr1_pru0_pru_r31_15 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (D13) mcasp0_axr1.pr1_pru0_pru_r30_6 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE5)/* (C12) mcasp0_ahclkr.pr1_pru0_pru_r30_3 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR0, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (D12) mcasp0_axr0.pr1_pru0_pru_r30_2 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSR, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (C13) mcasp0_fsr.pr1_pru0_pru_r30_5 */
+		>;
+	};
+
+	pru1_pins: pinmux-pru1-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE5)/*(R6) lcd_ac_bias_en.pr1_pru1_pru_r30_11 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE5)	/* (V5) lcd_pclk.pr1_pru1_pru_r30_10 */
+		>;
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ehrpwm0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ehrpwm0_pins>;
+};
+
+&epwmss1 {
+	status = "okay";
+};
+
+&ehrpwm1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ehrpwm1_pins>;
+};
+
+&i2c0 {
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+};
+
+&rtc {
+	system-power-controller;
+};
+
+&tscadc {
+	status = "okay";
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+		ti,chan-step-avg = <16 16 16 16 16 16 16 16>;
+		ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>;
+		ti,chan-step-sampledelay = <0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "otg";
+};
+
+&usb1 {
+	dr_mode = "host";
+};
+
+&pruss_tm {
+	status = "okay";
+};
+
+&pru0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pru0_pins>;
+};
+
+&pru1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pru1_pins>;
+};
diff --git a/arch/arm/boot/dts/am335x-regor-rdk.dts b/arch/arm/boot/dts/ti/omap/am335x-regor-rdk.dts
index 66a1360b83d5..66a1360b83d5 100644
--- a/arch/arm/boot/dts/am335x-regor-rdk.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-regor-rdk.dts
diff --git a/arch/arm/boot/dts/am335x-regor.dtsi b/arch/arm/boot/dts/ti/omap/am335x-regor.dtsi
index 6fbf4ac739e7..625db3bcd365 100644
--- a/arch/arm/boot/dts/am335x-regor.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-regor.dtsi
@@ -18,7 +18,7 @@
 	};
 
 	/* User IO */
-	user_leds: user_leds {
+	user_leds: user-leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_leds_pins>;
@@ -39,7 +39,7 @@
 
 /* User Leds */
 &am33xx_pinmux {
-	user_leds_pins: pinmux_user_leds {
+	user_leds_pins: pinmux-user-leds-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* lcd_hsync.gpio2_22 */
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* mcasp0_fsx.gpio3_15 */
@@ -49,7 +49,7 @@
 
 /* CAN Busses */
 &am33xx_pinmux {
-	dcan1_pins: pinmux_dcan1 {
+	dcan1_pins: pinmux-dcan1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT_PULLUP, MUX_MODE2)	/* uart0_ctsn.d_can1_tx */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE2)	/* uart0_rtsn.d_can1_rx */
@@ -65,7 +65,7 @@
 
 /* Ethernet */
 &am33xx_pinmux {
-	ethernet1_pins: pinmux_ethernet1 {
+	ethernet1_pins: pinmux-ethernet1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT, MUX_MODE1)		/* gpmc_a0.mii2_txen */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE1)	/* gpmc_a1.mii2_rxdv */
@@ -85,23 +85,22 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
+	status = "okay";
 	phy-handle = <&phy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
 
-&mac {
-	slaves = <2>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
-	dual_emac = <1>;
 };
 
 /* GPIOs */
@@ -109,7 +108,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&user_gpios_pins>;
 
-	user_gpios_pins: pinmux_user_gpios {
+	user_gpios_pins: pinmux-user-gpios-pins {
 		pinctrl-single,pins = <
 			/* DIGIN 1-4 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT, MUX_MODE7)		/* gpmc_ad11.gpio0_27 */
@@ -127,7 +126,7 @@
 
 /* MMC */
 &am33xx_pinmux {
-	mmc1_pins: pinmux_mmc1 {
+	mmc1_pins: pinmux-mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -156,14 +155,14 @@
 
 /* UARTs */
 &am33xx_pinmux {
-	uart0_pins: pinmux_uart0 {
+	uart0_pins: pinmux-uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart2_pins: pinmux_uart2 {
+	uart2_pins: pinmux-uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_tx_clk.uart2_rxd */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* mii1_rx_clk.uart2_txd */
@@ -185,7 +184,7 @@
 
 /* RS485 - UART1 */
 &am33xx_pinmux {
-	uart1_rs485_pins: pinmux_uart1_rs485_pins {
+	uart1_rs485_pins: pinmux-uart1-rs485-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-common.dtsi
index 8678e6e35493..a138eb356874 100644
--- a/arch/arm/boot/dts/am335x-sancloud-bbe.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-common.dtsi
@@ -1,23 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
-/dts-v1/;
-
-#include "am33xx.dtsi"
-#include "am335x-bone-common.dtsi"
-#include "am335x-boneblack-common.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
-	model = "SanCloud BeagleBone Enhanced";
-	compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
-};
 
 &am33xx_pinmux {
-	pinctrl-names = "default";
-
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
@@ -35,7 +22,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -53,85 +40,28 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
-		pinctrl-single,pins = <
-			/* MDIO */
-			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
-		>;
-	};
-
-	davinci_mdio_sleep: davinci_mdio_sleep {
-		pinctrl-single,pins = <
-			/* MDIO reset value */
-			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7)
-		>;
-	};
-
-	usb_hub_ctrl: usb_hub_ctrl {
+	usb_hub_ctrl: usb-hub-ctrl-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT_PULLUP, MUX_MODE7)     /* rmii1_refclk.gpio0_29 */
 		>;
 	};
-
-	mpu6050_pins: pinmux_mpu6050_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT, MUX_MODE7)    /* uart0_ctsn.gpio1_8 */
-		>;
-	};
-
-	lps3331ap_pins: pinmux_lps3331ap_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT, MUX_MODE7)     /* gpmc_a10.gpio1_26 */
-		>;
-	};
 };
 
-&mac {
-	pinctrl-names = "default", "sleep";
+&mac_sw {
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	status = "okay";
-};
-
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
-
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
 };
 
-&cpsw_emac0 {
-	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii-txid";
+&cpsw_port1 {
+	phy-mode = "rgmii-id";
 };
 
 &i2c0 {
-	lps331ap: barometer@5c {
-		compatible = "st,lps331ap-press";
-		st,drdy-int-pin = <1>;
-		reg = <0x5c>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <26 IRQ_TYPE_EDGE_RISING>;
-	};
-
-	mpu6050: accelerometer@68 {
-		compatible = "invensense,mpu6050";
-		reg = <0x68>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
-		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
-	};
-
 	usb2512b: usb-hub@2c {
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_hub_ctrl>;
 		compatible = "microchip,usb2512b";
 		reg = <0x2c>;
 		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
-		/* wifi on port 4 */
 	};
 };
diff --git a/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-extended-wifi.dts b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-extended-wifi.dts
new file mode 100644
index 000000000000..5522759def26
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-extended-wifi.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Sancloud Ltd
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include "am335x-sancloud-bbe-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "SanCloud BeagleBone Enhanced Extended WiFi";
+	compatible = "sancloud,am335x-boneenhanced",
+		     "ti,am335x-bone-black",
+		     "ti,am335x-bone",
+		     "ti,am33xx";
+
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+	};
+};
+
+&am33xx_pinmux {
+	mmc3_pins: mmc3-pins {
+		pinctrl-single,pins = <
+			/* gpmc_a9.gpio1_25: RADIO_EN */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_OUTPUT_PULLUP, MUX_MODE7)
+
+			/* gpmc_ad12.mmc2_dat0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_ad13.mmc2_dat1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_ad14.mmc2_dat2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_ad15.mmc2_dat3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_csn3.mmc2_cmd */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_clk.mmc2_clk */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE3)
+		>;
+	};
+
+	bluetooth_pins: bluetooth-pins {
+		pinctrl-single,pins = <
+			/* event_intr0.gpio0_19 */
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+	};
+
+	uart1_pins: uart1-pins {
+		pinctrl-single,pins = <
+			/* uart1_rxd */
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)
+
+			/* uart1_txd */
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)
+
+			/* uart1_ctsn */
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0)
+
+			/* uart1_rtsn */
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+		>;
+	};
+};
+
+&i2c2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	ti,needs-special-hs-handling;
+	keep-power-in-suspend;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins>;
+	dmas = <&edma_xbar 12 0 1
+		&edma_xbar 13 0 2>;
+	dma-names = "tx", "rx";
+	clock-frequency = <50000000>;
+	max-frequency = <50000000>;
+};
+
+&uart1 {
+	status = "okay";
+
+	bluetooth {
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1_pins &bluetooth_pins>;
+		compatible = "qcom,qca6174-bt";
+		enable-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+		clocks = <&l4ls_clkctrl AM3_L4LS_UART2_CLKCTRL 0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-lite.dts b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-lite.dts
new file mode 100644
index 000000000000..b1b400226d83
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe-lite.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2021 SanCloud Ltd
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include "am335x-sancloud-bbe-common.dtsi"
+
+/ {
+	model = "SanCloud BeagleBone Enhanced Lite";
+	compatible = "sancloud,am335x-boneenhanced",
+		     "ti,am335x-bone-black",
+		     "ti,am335x-bone",
+		     "ti,am33xx";
+};
+
+&am33xx_pinmux {
+	bb_spi0_pins: bb-spi0-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT, MUX_MODE0)
+		>;
+	};
+};
+
+&spi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&bb_spi0_pins>;
+
+	channel@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "micron,spi-authenta";
+
+		reg = <0>;
+		spi-max-frequency = <16000000>;
+		spi-cpha;
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe.dts
new file mode 100644
index 000000000000..32669346cefe
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am335x-sancloud-bbe.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
+#include "am335x-sancloud-bbe-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "SanCloud BeagleBone Enhanced";
+	compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+};
+
+&am33xx_pinmux {
+	mpu6050_pins: mpu6050-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT, MUX_MODE7)    /* uart0_ctsn.gpio1_8 */
+		>;
+	};
+
+	lps3331ap_pins: lps3331ap-pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT, MUX_MODE7)     /* gpmc_a10.gpio1_26 */
+		>;
+	};
+};
+
+&i2c0 {
+	lps331ap: barometer@5c {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lps3331ap_pins>;
+		compatible = "st,lps331ap-press";
+		st,drdy-int-pin = <1>;
+		reg = <0x5c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	mpu6050: accelerometer@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu6050_pins>;
+		compatible = "invensense,mpu6050";
+		reg = <0x68>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-sbc-t335.dts b/arch/arm/boot/dts/ti/omap/am335x-sbc-t335.dts
index a3f6bc4072d9..596774c84744 100644
--- a/arch/arm/boot/dts/am335x-sbc-t335.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-sbc-t335.dts
@@ -64,7 +64,7 @@
 
 &am33xx_pinmux {
 	/* Display */
-	lcd_pins_default: lcd_pins_default {
+	lcd_pins_default: lcd-default-pins {
 		pinctrl-single,pins = <
 			/* gpmc_ad8.lcd_data23 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_OUTPUT, MUX_MODE1)
@@ -105,7 +105,7 @@
 		>;
 	};
 
-	lcd_pins_sleep: lcd_pins_sleep {
+	lcd_pins_sleep: lcd-sleep-pins {
 		pinctrl-single,pins = <
 			/* gpmc_ad8.lcd_data23 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -155,13 +155,13 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		reg = <0x26>;
-		dvi_ena {
+		dvi-ena-hog {
 			gpio-hog;
 			gpios = <13 GPIO_ACTIVE_HIGH>;
 			output-high;
 			line-name = "dvi-enable";
 		};
-		lcd_ena {
+		lcd-ena-hog {
 			gpio-hog;
 			gpios = <11 GPIO_ACTIVE_HIGH>;
 			output-high;
diff --git a/arch/arm/boot/dts/am335x-shc.dts b/arch/arm/boot/dts/ti/omap/am335x-shc.dts
index 1eaa26533466..9297cb1efcd4 100644
--- a/arch/arm/boot/dts/am335x-shc.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-shc.dts
@@ -36,10 +36,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		back_button {
+		back-button {
 			label = "Back Button";
 			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_BACK>;
@@ -47,7 +47,7 @@
 			wakeup-source;
 		};
 
-		front_button {
+		front-button {
 			label = "Front Button";
 			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_FRONT>;
@@ -117,18 +117,6 @@
 	status = "okay";
 };
 
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
-
-	ethernetphy0: ethernet-phy@0 {
-		reg = <0>;
-		smsc,disable-energy-detect;
-	};
-};
-
 &epwmss1 {
 	status = "okay";
 
@@ -140,14 +128,14 @@
 };
 
 &gpio1 {
-	hmtc_rst {
+	hmtc-rst-hog {
 		gpio-hog;
 		gpios = <24 GPIO_ACTIVE_LOW>;
 		output-high;
 		line-name = "homematic_reset";
 	};
 
-	hmtc_prog {
+	hmtc-prog-hog {
 		gpio-hog;
 		gpios = <27 GPIO_ACTIVE_LOW>;
 		output-high;
@@ -156,14 +144,14 @@
 };
 
 &gpio3 {
-	zgb_rst {
+	zgb-rst-hog {
 		gpio-hog;
 		gpios = <18 GPIO_ACTIVE_LOW>;
 		output-low;
 		line-name = "zigbee_reset";
 	};
 
-	zgb_boot {
+	zgb-boot-hog {
 		gpio-hog;
 		gpios = <19 GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -193,15 +181,31 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	slaves = <1>;
-	cpsw_emac0: slave@200 {
-		phy-mode = "mii";
-		phy-handle = <&ethernetphy0>;
+};
+
+&cpsw_port1 {
+	phy-mode = "mii";
+	phy-handle = <&ethernetphy0>;
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&davinci_mdio_sw {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+
+	ethernetphy0: ethernet-phy@0 {
+		reg = <0>;
+		smsc,disable-energy-detect;
 	};
 };
 
@@ -362,14 +366,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&clkout2_pin>;
 
-	clkout2_pin: pinmux_clkout2_pin {
+	clkout2_pin: clkout2-pins {
 		pinctrl-single,pins = <
 			/* xdma_event_intr1.clkout2 */
 			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT, MUX_MODE6)
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE0)
@@ -388,7 +392,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -407,14 +411,14 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -422,13 +426,13 @@
 		>;
 	};
 
-	ehrpwm1_pins: pinmux_ehrpwm1 {
+	ehrpwm1_pins: ehrpwm1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT, MUX_MODE6) /* gpmc_a3.gpio1_19 */
 		>;
 	};
 
-	emmc_pins: pinmux_emmc_pins {
+	emmc_pins: emmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT, MUX_MODE2)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2)
@@ -443,20 +447,20 @@
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE0)
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE5)
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT, MUX_MODE3)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT, MUX_MODE3)
@@ -467,7 +471,7 @@
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_OUTPUT, MUX_MODE0)
@@ -476,7 +480,7 @@
 		>;
 	};
 
-	uart1_pins: pinmux_uart1 {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT, MUX_MODE0)
@@ -485,21 +489,21 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE1)
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE1)
 		>;
 	};
 
-	uart4_pins: pinmux_uart4_pins {
+	uart4_pins: uart4-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLUP, MUX_MODE6)
 		>;
 	};
 
-	user_leds_s0: user_leds_s0 {
+	user_leds_s0: user-leds-s0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_OUTPUT, MUX_MODE7)
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_OUTPUT, MUX_MODE7)
diff --git a/arch/arm/boot/dts/am335x-sl50.dts b/arch/arm/boot/dts/ti/omap/am335x-sl50.dts
index f4684c8eaffe..1115c812f6c8 100644
--- a/arch/arm/boot/dts/am335x-sl50.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-sl50.dts
@@ -213,7 +213,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&lwb_pins>;
 
-	audio_pins: pinmux_audio_pins {
+	audio_pins: audio-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE0)
@@ -223,31 +223,31 @@
 		>;
 	};
 
-	audio_pa_pins: pinmux_audio_pa_pins {
+	audio_pa_pins: audio-pa-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* SoundPA_en - mcasp0_aclkr.gpio3_18 */
 		>;
 	};
 
-	audio_mclk_pins: pinmux_audio_mclk_pins {
+	audio_mclk_pins: audio-mclk-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_a11.gpio1_27 */
 		>;
 	};
 
-	backlight0_pins: pinmux_backlight0_pins {
+	backlight0_pins: backlight0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_OUTPUT, MUX_MODE7)	/* gpmc_wen.gpio2_4 */
 		>;
 	};
 
-	backlight1_pins: pinmux_backlight1_pins {
+	backlight1_pins: backlight1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_OUTPUT, MUX_MODE7)     /* gpmc_ad10.gpio0_26 */
 		>;
 	};
 
-	lcd_pins: pinmux_lcd_pins {
+	lcd_pins: lcd-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
@@ -272,7 +272,7 @@
 		>;
 	};
 
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a5.gpio1_21 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT, MUX_MODE7)	/* gpmc_a6.gpio1_22 */
@@ -281,42 +281,42 @@
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
+	uart0_pins: uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart4_pins: pinmux_uart4_pins {
+	uart4_pins: uart4-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6)	/* gpmc_wait0.uart4_rxd */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6)	/* gpmc_wpn.uart4_txd */
 		>;
 	};
 
-	i2c0_pins: pinmux_i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0)
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
 			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -335,7 +335,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -354,7 +354,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
@@ -364,7 +364,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
@@ -372,19 +372,19 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE7)		/* uart0_rtsn.gpio1_9 */
 		>;
 	};
 
-	emmc_pwrseq_pins: pinmux_emmc_pwrseq_pins {
+	emmc_pwrseq_pins: emmc-pwrseq-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_a4.gpio1_20 */
 		>;
 	};
 
-	emmc_pins: pinmux_emmc_pins {
+	emmc_pins: emmc-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn1.mmc1_clk */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2)	/* gpmc_csn2.mmc1_cmd */
@@ -399,20 +399,20 @@
 		>;
 	};
 
-	ehrpwm1_pins: pinmux_ehrpwm1a_pins {
+	ehrpwm1_pins: ehrpwm1a-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT, MUX_MODE6)	/* gpmc_a2.ehrpwm1a */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT, MUX_MODE6)	/* gpmc_a3.ehrpwm1b */
 		>;
 	};
 
-	rtc0_irq_pins: pinmux_rtc0_irq_pins {
+	rtc0_irq_pins: rtc0-irq-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT_PULLUP, MUX_MODE7)     /* gpmc_ad9.gpio0_23 */
 		>;
 	};
 
-	spi0_pins: pinmux_spi0_pins {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0)	/* SPI0_MOSI */
 			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE0)	/* SPI0_MISO */
@@ -422,7 +422,7 @@
 		>;
 	};
 
-	lwb_pins: pinmux_lwb_pins {
+	lwb_pins: lwb-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE7)	/* nKbdInt - gpmc_ad12.gpio1_12 */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE7)	/* nKbdReset - gpmc_ad13.gpio1_13 */
@@ -588,7 +588,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
 
-	flash: n25q032@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q032";
@@ -597,7 +597,7 @@
 	};
 };
 
-#include "tps65217.dtsi"
+#include "../../tps65217.dtsi"
 
 &tps {
 	ti,pmic-shutdown-controller;
@@ -661,20 +661,24 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "mii";
 	phy-handle = <&ethphy0>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&mac {
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&mac_sw {
 	status = "okay";
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 };
 
-&davinci_mdio {
-	status = "okay";
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
diff --git a/arch/arm/boot/dts/am335x-wega-rdk.dts b/arch/arm/boot/dts/ti/omap/am335x-wega-rdk.dts
index 866b5f0cbfbc..866b5f0cbfbc 100644
--- a/arch/arm/boot/dts/am335x-wega-rdk.dts
+++ b/arch/arm/boot/dts/ti/omap/am335x-wega-rdk.dts
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/ti/omap/am335x-wega.dtsi
index 1359bf8715e6..cb27ff464dbe 100644
--- a/arch/arm/boot/dts/am335x-wega.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am335x-wega.dtsi
@@ -8,8 +8,34 @@
 	model = "Phytec AM335x phyBOARD-WEGA";
 	compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx";
 
-	sound: sound_iface {
-		compatible = "ti,da830-evm-audio";
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "snd-wega";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&sound_iface_main>;
+		simple-audio-card,frame-master = <&sound_iface_main>;
+		simple-audio-card,mclk-fs = <32>;
+		simple-audio-card,widgets =
+					"Line", "Line In",
+					"Line", "Line Out",
+					"Speaker", "Speaker";
+		simple-audio-card,routing =
+					"Line Out", "LLOUT",
+					"Line Out", "RLOUT",
+					"Speaker", "SPOP",
+					"Speaker", "SPOM",
+					"LINE1L", "Line In",
+					"LINE1R", "Line In";
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+		};
+
+		sound_iface_main: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3007>;
+			clocks = <&mcasp0_fck>;
+		};
+
 	};
 
 	vcc3v3: fixedregulator1 {
@@ -23,7 +49,7 @@
 
 /* Audio */
 &am33xx_pinmux {
-	mcasp0_pins: pinmux_mcasp0 {
+	mcasp0_pins: pinmux-mcasp0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)
@@ -36,6 +62,7 @@
 
 &i2c0 {
 	tlv320aic3007: tlv320aic3007@18 {
+		#sound-dai-cells = <0>;
 		compatible = "ti,tlv320aic3007";
 		reg = <0x18>;
 		AVDD-supply = <&vcc3v3>;
@@ -47,6 +74,7 @@
 };
 
 &mcasp0 {
+	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcasp0_pins>;
 	op-mode = <0>; /* DAVINCI_MCASP_IIS_MODE */
@@ -55,27 +83,14 @@
 		2 1 0 0 /* # 0: INACTIVE, 1: TX, 2: RX */
 	>;
 	tx-num-evt = <16>;
-	rt-num-evt = <16>;
+	rx-num-evt = <16>;
 	status = "okay";
 };
 
-&sound {
-	ti,model = "AM335x-Wega";
-	ti,audio-codec = <&tlv320aic3007>;
-	ti,mcasp-controller = <&mcasp0>;
-	ti,audio-routing =
-		"Line Out",		"LLOUT",
-		"Line Out",		"RLOUT",
-		"LINE1L",		"Line In",
-		"LINE1R",		"Line In";
-	clocks = <&mcasp0_fck>;
-	clock-names = "mclk";
-	status = "okay";
-};
 
 /* CAN Busses */
 &am33xx_pinmux {
-	dcan1_pins: pinmux_dcan1 {
+	dcan1_pins: pinmux-dcan1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT_PULLUP, MUX_MODE2) /* uart0_ctsn.d_can1_tx */
 			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE2) /* uart0_rtsn.d_can1_rx */
@@ -91,7 +106,7 @@
 
 /* Ethernet */
 &am33xx_pinmux {
-	ethernet1_pins: pinmux_ethernet1 {
+	ethernet1_pins: pinmux-ethernet1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT, MUX_MODE1)		/* gpmc_a0.mii2_txen */
 			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE1)	/* gpmc_a1.mii2_rxdv */
@@ -111,28 +126,27 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
+	status = "okay";
 	phy-handle = <&phy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
 
-&mac {
-	slaves = <2>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
-	dual_emac = <1>;
 };
 
 /* MMC */
 &am33xx_pinmux {
-	mmc1_pins: pinmux_mmc1 {
+	mmc1_pins: pinmux-mmc1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
@@ -162,14 +176,14 @@
 
 /* UARTs */
 &am33xx_pinmux {
-	uart0_pins: pinmux_uart0 {
+	uart0_pins: pinmux-uart0-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: pinmux-uart1-pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
 			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
diff --git a/arch/arm/boot/dts/am33xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/am33xx-clocks.dtsi
index dced92a8970e..d34483ae1778 100644
--- a/arch/arm/boot/dts/am33xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am33xx-clocks.dtsi
@@ -5,251 +5,288 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &scm_clocks {
-	sys_clkin_ck: sys_clkin_ck@40 {
+	sys_clkin_ck: clock-sys-clkin-22@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin_ck";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
 		ti,bit-shift = <22>;
 		reg = <0x0040>;
 	};
 
-	adc_tsc_fck: adc_tsc_fck {
+	adc_tsc_fck: clock-adc-tsc-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "adc_tsc_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan0_fck: dcan0_fck {
+	dcan0_fck: clock-dcan0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan1_fck: dcan1_fck {
+	dcan1_fck: clock-dcan1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp0_fck: mcasp0_fck {
+	mcasp0_fck: clock-mcasp0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp1_fck: mcasp1_fck {
+	mcasp1_fck: clock-mcasp1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex0_fck: smartreflex0_fck {
+	smartreflex0_fck: clock-smartreflex0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex1_fck: smartreflex1_fck {
+	smartreflex1_fck: clock-smartreflex1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	sha0_fck: sha0_fck {
+	sha0_fck: clock-sha0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sha0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	aes0_fck: aes0_fck {
+	aes0_fck: clock-aes0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "aes0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	rng_fck: rng_fck {
+	rng_fck: clock-rng-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "rng_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	ehrpwm0_tbclk: ehrpwm0_tbclk@44e10664 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l4ls_gclk>;
-		ti,bit-shift = <0>;
-		reg = <0x0664>;
-	};
+	clock@664 {
+		compatible = "ti,clksel";
+		reg = <0x664>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	ehrpwm1_tbclk: ehrpwm1_tbclk@44e10664 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l4ls_gclk>;
-		ti,bit-shift = <1>;
-		reg = <0x0664>;
-	};
+		ehrpwm0_tbclk: clock-ehrpwm0-tbclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "ehrpwm0_tbclk";
+			clocks = <&l4ls_gclk>;
+			ti,bit-shift = <0>;
+		};
 
-	ehrpwm2_tbclk: ehrpwm2_tbclk@44e10664 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l4ls_gclk>;
-		ti,bit-shift = <2>;
-		reg = <0x0664>;
+		ehrpwm1_tbclk: clock-ehrpwm1-tbclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "ehrpwm1_tbclk";
+			clocks = <&l4ls_gclk>;
+			ti,bit-shift = <1>;
+		};
+
+		ehrpwm2_tbclk: clock-ehrpwm2-tbclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "ehrpwm2_tbclk";
+			clocks = <&l4ls_gclk>;
+			ti,bit-shift = <2>;
+		};
 	};
 };
 &prcm_clocks {
-	clk_32768_ck: clk_32768_ck {
+	clk_32768_ck: clock-clk-32768 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32768_ck";
 		clock-frequency = <32768>;
 	};
 
-	clk_rc32k_ck: clk_rc32k_ck {
+	clk_rc32k_ck: clock-clk-rc32k {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_rc32k_ck";
 		clock-frequency = <32000>;
 	};
 
-	virt_19200000_ck: virt_19200000_ck {
+	virt_19200000_ck: clock-virt-19200000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
-	virt_24000000_ck: virt_24000000_ck {
+	virt_24000000_ck: clock-virt-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_24000000_ck";
 		clock-frequency = <24000000>;
 	};
 
-	virt_25000000_ck: virt_25000000_ck {
+	virt_25000000_ck: clock-virt-25000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_25000000_ck";
 		clock-frequency = <25000000>;
 	};
 
-	virt_26000000_ck: virt_26000000_ck {
+	virt_26000000_ck: clock-virt-26000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
-	tclkin_ck: tclkin_ck {
+	tclkin_ck: clock-tclkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "tclkin_ck";
 		clock-frequency = <12000000>;
 	};
 
-	dpll_core_ck: dpll_core_ck@490 {
+	dpll_core_ck: clock@490 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x0490>, <0x045c>, <0x0468>;
+		reg = <0x0490>, <0x045c>, <0x0468>, <0x0460>, <0x0464>;
 	};
 
-	dpll_core_x2_ck: dpll_core_x2_ck {
+	dpll_core_x2_ck: clock-dpll-core-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_m4_ck: dpll_core_m4_ck@480 {
+	dpll_core_m4_ck: clock-dpll-core-m4@480 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m4_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0480>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_core_m5_ck: dpll_core_m5_ck@484 {
+	dpll_core_m5_ck: clock-dpll-core-m5@484 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m5_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0484>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_core_m6_ck: dpll_core_m6_ck@4d8 {
+	dpll_core_m6_ck: clock-dpll-core-m6@4d8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m6_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x04d8>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck@488 {
+	dpll_mpu_ck: clock@488 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x0488>, <0x0420>, <0x042c>;
+		reg = <0x0488>, <0x0420>, <0x042c>, <0x0424>, <0x0428>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck@4a8 {
+	dpll_mpu_m2_ck: clock-dpll-mpu-m2@4a8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		reg = <0x04a8>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck@494 {
+	dpll_ddr_ck: clock@494 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-clock";
+		clock-output-names = "dpll_ddr_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x0494>, <0x0434>, <0x0440>;
+		reg = <0x0494>, <0x0434>, <0x0440>, <0x0438>, <0x043c>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck@4a0 {
+	dpll_ddr_m2_ck: clock-dpll-ddr-m2@4a0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m2_ck";
 		clocks = <&dpll_ddr_ck>;
 		ti,max-div = <31>;
 		reg = <0x04a0>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_ddr_m2_div2_ck: dpll_ddr_m2_div2_ck {
+	dpll_ddr_m2_div2_ck: clock-dpll-ddr-m2-div2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_ddr_m2_div2_ck";
 		clocks = <&dpll_ddr_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	dpll_disp_ck: dpll_disp_ck@498 {
+	dpll_disp_ck: clock@498 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-clock";
+		clock-output-names = "dpll_disp_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x0498>, <0x0448>, <0x0454>;
+		reg = <0x0498>, <0x0448>, <0x0454>, <0x044c>, <0x0450>;
 	};
 
-	dpll_disp_m2_ck: dpll_disp_m2_ck@4a4 {
+	dpll_disp_m2_ck: clock-dpll-disp-m2@4a4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_disp_m2_ck";
 		clocks = <&dpll_disp_ck>;
 		ti,max-div = <31>;
 		reg = <0x04a4>;
@@ -257,418 +294,484 @@
 		ti,set-rate-parent;
 	};
 
-	dpll_per_ck: dpll_per_ck@48c {
+	dpll_per_ck: clock@48c {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-j-type-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x048c>, <0x0470>, <0x049c>;
+		reg = <0x048c>, <0x0470>, <0x049c>, <0x0474>, <0x0478>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck@4ac {
+	dpll_per_m2_ck: clock-dpll-per-m2@4ac {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		reg = <0x04ac>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+	dpll_per_m2_div4_wkupdm_ck: clock-dpll-per-m2-div4-wkupdm {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_wkupdm_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+	dpll_per_m2_div4_ck: clock-dpll-per-m2-div4 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	clk_24mhz: clk_24mhz {
+	clk_24mhz: clock-clk-24mhz {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clk_24mhz";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
 	};
 
-	clkdiv32k_ck: clkdiv32k_ck {
+	clkdiv32k_ck: clock-clkdiv32k {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clkdiv32k_ck";
 		clocks = <&clk_24mhz>;
 		clock-mult = <1>;
 		clock-div = <732>;
 	};
 
-	l3_gclk: l3_gclk {
+	l3_gclk: clock-l3-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	pruss_ocp_gclk: pruss_ocp_gclk@530 {
+	pruss_ocp_gclk: clock-pruss-ocp-gclk@530 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "pruss_ocp_gclk";
 		clocks = <&l3_gclk>, <&dpll_disp_m2_ck>;
 		reg = <0x0530>;
 	};
 
-	mmu_fck: mmu_fck@914 {
+	mmu_fck: clock-mmu-fck-1@914 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "mmu_fck";
 		clocks = <&dpll_core_m4_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0914>;
 	};
 
-	timer1_fck: timer1_fck@528 {
+	timer1_fck: clock-timer1-fck@528 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer1_fck";
 		clocks = <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>;
 		reg = <0x0528>;
 	};
 
-	timer2_fck: timer2_fck@508 {
+	timer2_fck: clock-timer2-fck@508 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer2_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0508>;
 	};
 
-	timer3_fck: timer3_fck@50c {
+	timer3_fck: clock-timer3-fck@50c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer3_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x050c>;
 	};
 
-	timer4_fck: timer4_fck@510 {
+	timer4_fck: clock-timer4-fck@510 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer4_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0510>;
 	};
 
-	timer5_fck: timer5_fck@518 {
+	timer5_fck: clock-timer5-fck@518 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer5_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0518>;
 	};
 
-	timer6_fck: timer6_fck@51c {
+	timer6_fck: clock-timer6-fck@51c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer6_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x051c>;
 	};
 
-	timer7_fck: timer7_fck@504 {
+	timer7_fck: clock-timer7-fck@504 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer7_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0504>;
 	};
 
-	usbotg_fck: usbotg_fck@47c {
+	usbotg_fck: clock-usbotg-fck-8@47c {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usbotg_fck";
 		clocks = <&dpll_per_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x047c>;
 	};
 
-	dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+	dpll_core_m4_div2_ck: clock-dpll-core-m4-div2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_core_m4_div2_ck";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	ieee5000_fck: ieee5000_fck@e4 {
+	ieee5000_fck: clock-ieee5000-fck-1@e4 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ieee5000_fck";
 		clocks = <&dpll_core_m4_div2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x00e4>;
 	};
 
-	wdt1_fck: wdt1_fck@538 {
+	wdt1_fck: clock-wdt1-fck@538 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wdt1_fck";
 		clocks = <&clk_rc32k_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0538>;
 	};
 
-	l4_rtc_gclk: l4_rtc_gclk {
+	l4_rtc_gclk: clock-l4-rtc-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4_rtc_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l4hs_gclk: l4hs_gclk {
+	l4hs_gclk: clock-l4hs-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4hs_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l3s_gclk: l3s_gclk {
+	l3s_gclk: clock-l3s-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3s_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l4fw_gclk: l4fw_gclk {
+	l4fw_gclk: clock-l4fw-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4fw_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l4ls_gclk: l4ls_gclk {
+	l4ls_gclk: clock-l4ls-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4ls_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	sysclk_div_ck: sysclk_div_ck {
+	sysclk_div_ck: clock-sysclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sysclk_div_ck";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+	cpsw_125mhz_gclk: clock-cpsw-125mhz-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_125mhz_gclk";
 		clocks = <&dpll_core_m5_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk@520 {
+	cpsw_cpts_rft_clk: clock-cpsw-cpts-rft@520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "cpsw_cpts_rft_clk";
 		clocks = <&dpll_core_m5_ck>, <&dpll_core_m4_ck>;
 		reg = <0x0520>;
 	};
 
-	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck@53c {
+	gpio0_dbclk_mux_ck: clock-gpio0-dbclk-mux@53c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpio0_dbclk_mux_ck";
 		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x053c>;
 	};
 
-	lcd_gclk: lcd_gclk@534 {
+	lcd_gclk: clock-lcd-gclk@534 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "lcd_gclk";
 		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
 		reg = <0x0534>;
 		ti,set-rate-parent;
 	};
 
-	mmc_clk: mmc_clk {
+	mmc_clk: clock-mmc {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mmc_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck@52c {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x052c>;
-	};
+	clock@52c {
+		compatible = "ti,clksel";
+		reg = <0x52c>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	gfx_fck_div_ck: gfx_fck_div_ck@52c {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&gfx_fclk_clksel_ck>;
-		reg = <0x052c>;
-		ti,max-div = <2>;
-	};
+		gfx_fclk_clksel_ck: clock-gfx-fclk-clksel {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "gfx_fclk_clksel_ck";
+			clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
+			ti,bit-shift = <1>;
+		};
 
-	sysclkout_pre_ck: sysclkout_pre_ck@700 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
-		reg = <0x0700>;
+		gfx_fck_div_ck: clock-gfx-fck-div {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "gfx_fck_div_ck";
+			clocks = <&gfx_fclk_clksel_ck>;
+			ti,max-div = <2>;
+		};
 	};
 
-	clkout2_div_ck: clkout2_div_ck@700 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&sysclkout_pre_ck>;
-		ti,bit-shift = <3>;
-		ti,max-div = <8>;
-		reg = <0x0700>;
-	};
+	clock@700 {
+		compatible = "ti,clksel";
+		reg = <0x700>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	clkout2_ck: clkout2_ck@700 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&clkout2_div_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0700>;
+		sysclkout_pre_ck: clock-sysclkout-pre {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "sysclkout_pre_ck";
+			clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
+		};
+
+		clkout2_div_ck: clock-clkout2-div {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "clkout2_div_ck";
+			clocks = <&sysclkout_pre_ck>;
+			ti,bit-shift = <3>;
+			ti,max-div = <8>;
+		};
+
+		clkout2_ck: clock-clkout2 {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "clkout2_ck";
+			clocks = <&clkout2_div_ck>;
+			ti,bit-shift = <7>;
+		};
 	};
 };
 
 &prcm {
-	per_cm: per-cm@0 {
+	per_cm: clock@0 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "per_cm";
 		reg = <0x0 0x400>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x0 0x400>;
 
-		l4ls_clkctrl: l4ls-clkctrl@38 {
+		l4ls_clkctrl: clock@38 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4ls_clkctrl";
 			reg = <0x38 0x2c>, <0x6c 0x28>, <0xac 0xc>, <0xc0 0x1c>, <0xec 0xc>, <0x10c 0x8>, <0x130 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l3s_clkctrl: l3s-clkctrl@1c {
+		l3s_clkctrl: clock@1c {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3s_clkctrl";
 			reg = <0x1c 0x4>, <0x30 0x8>, <0x68 0x4>, <0xf8 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l3_clkctrl: l3-clkctrl@24 {
+		l3_clkctrl: clock@24 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_clkctrl";
 			reg = <0x24 0xc>, <0x94 0x10>, <0xbc 0x4>, <0xdc 0x8>, <0xfc 0x8>;
 			#clock-cells = <2>;
 		};
 
-		l4hs_clkctrl: l4hs-clkctrl@120 {
+		l4hs_clkctrl: clock@120 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4hs_clkctrl";
 			reg = <0x120 0x4>;
 			#clock-cells = <2>;
 		};
 
-		pruss_ocp_clkctrl: pruss-ocp-clkctrl@e8 {
+		pruss_ocp_clkctrl: clock@e8 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "pruss_ocp_clkctrl";
 			reg = <0xe8 0x4>;
 			#clock-cells = <2>;
 		};
 
-		cpsw_125mhz_clkctrl: cpsw-125mhz-clkctrl@0 {
+		cpsw_125mhz_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "cpsw_125mhz_clkctrl";
 			reg = <0x0 0x18>;
 			#clock-cells = <2>;
 		};
 
-		lcdc_clkctrl: lcdc-clkctrl@18 {
+		lcdc_clkctrl: clock@18 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "lcdc_clkctrl";
 			reg = <0x18 0x4>;
 			#clock-cells = <2>;
 		};
 
-		clk_24mhz_clkctrl: clk-24mhz-clkctrl@14c {
+		clk_24mhz_clkctrl: clock@14c {
 			compatible = "ti,clkctrl";
+			clock-output-names = "clk_24mhz_clkctrl";
 			reg = <0x14c 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	wkup_cm: wkup-cm@400 {
+	wkup_cm: clock@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkup_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x400 0x100>;
 
-		l4_wkup_clkctrl: l4-wkup-clkctrl@0 {
+		l4_wkup_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_clkctrl";
 			reg = <0x0 0x10>, <0xb4 0x24>;
 			#clock-cells = <2>;
 		};
 
-		l3_aon_clkctrl: l3-aon-clkctrl@14 {
+		l3_aon_clkctrl: clock@14 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_aon_clkctrl";
 			reg = <0x14 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l4_wkup_aon_clkctrl: l4-wkup-aon-clkctrl@b0 {
+		l4_wkup_aon_clkctrl: clock@b0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_aon_clkctrl";
 			reg = <0xb0 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	mpu_cm: mpu-cm@600 {
+	mpu_cm: clock@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x600 0x100>;
 
-		mpu_clkctrl: mpu-clkctrl@0 {
+		mpu_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x0 0x8>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_rtc_cm: l4-rtc-cm@800 {
+	l4_rtc_cm: clock@800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_rtc_cm";
 		reg = <0x800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x800 0x100>;
 
-		l4_rtc_clkctrl: l4-rtc-clkctrl@0 {
+		l4_rtc_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_rtc_clkctrl";
 			reg = <0x0 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	gfx_l3_cm: gfx-l3-cm@900 {
+	gfx_l3_cm: clock@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gfx_l3_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x900 0x100>;
 
-		gfx_l3_clkctrl: gfx-l3-clkctrl@0 {
+		gfx_l3_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gfx_l3_clkctrl";
 			reg = <0x0 0x8>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_cefuse_cm: l4-cefuse-cm@a00 {
+	l4_cefuse_cm: clock@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_cefuse_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xa00 0x100>;
 
-		l4_cefuse_clkctrl: l4-cefuse-clkctrl@0 {
+		l4_cefuse_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_cefuse_clkctrl";
 			reg = <0x0 0x24>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/ti/omap/am33xx-l4.dtsi
index 3a8a205c27b5..d6a143abae5f 100644
--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am33xx-l4.dtsi
@@ -1,5 +1,8 @@
 &l4_wkup {						/* 0x44c00000 */
-	compatible = "ti,am33xx-l4-wkup", "simple-bus";
+	compatible = "ti,am33xx-l4-wkup", "simple-pm-bus";
+	power-domains = <&prm_wkup>;
+	clocks = <&l4_wkup_clkctrl AM3_L4_WKUP_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x44c00000 0x800>,
 	      <0x44c00800 0x800>,
 	      <0x44c01000 0x400>,
@@ -12,7 +15,7 @@
 		 <0x00200000 0x44e00000 0x100000>;	/* segment 2 */
 
 	segment@0 {					/* 0x44c00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -22,7 +25,7 @@
 	};
 
 	segment@100000 {					/* 0x44d00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00100000 0x004000>,	/* ap 4 */
@@ -34,23 +37,27 @@
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0x0 0x4>;
 			reg-names = "rev";
+			clocks = <&l4_wkup_aon_clkctrl AM3_L4_WKUP_AON_WKUP_M3_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <0x0 0x0 0x4000>;
-			status = "disabled";
-		};
+			ranges = <0x00000000 0x00000000 0x4000>,
+				 <0x00080000 0x00080000 0x2000>;
 
-		target-module@80000 {			/* 0x44d80000, ap 6 10.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0x80000 0x2000>;
+			wkup_m3: cpu@0 {
+				compatible = "ti,am3352-wkup-m3";
+				reg = <0x00000000 0x4000>,
+				      <0x00080000 0x2000>;
+				reg-names = "umem", "dmem";
+				resets = <&prm_wkup 3>;
+				reset-names = "rstctrl";
+				ti,pm-firmware = "am335x-pm-firmware.elf";
+			};
 		};
 	};
 
 	segment@200000 {					/* 0x44e00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00200000 0x002000>,	/* ap 8 */
@@ -151,6 +158,18 @@
 
 			gpio0: gpio@0 {
 				compatible = "ti,omap4-gpio";
+				gpio-ranges =	<&am33xx_pinmux  0  82 8>,
+						<&am33xx_pinmux  8  52 4>,
+						<&am33xx_pinmux 12  94 4>,
+						<&am33xx_pinmux 16  71 2>,
+						<&am33xx_pinmux 18 135 1>,
+						<&am33xx_pinmux 19 108 2>,
+						<&am33xx_pinmux 21  73 1>,
+						<&am33xx_pinmux 22   8 2>,
+						<&am33xx_pinmux 26  10 2>,
+						<&am33xx_pinmux 28  74 1>,
+						<&am33xx_pinmux 29  81 1>,
+						<&am33xx_pinmux 30  28 2>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -225,7 +244,6 @@
 
 		target-module@d000 {			/* 0x44e0d000, ap 20 38.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "adc_tsc";
 			reg = <0xd000 0x4>,
 			      <0xd010 0x4>;
 			reg-names = "rev", "sysc";
@@ -241,28 +259,33 @@
 			ranges = <0x00000000 0x0000d000 0x00001000>,
 				 <0x00001000 0x0000e000 0x00001000>;
 
-				tscadc: tscadc@0 {
-					compatible = "ti,am3359-tscadc";
-					reg = <0x0 0x1000>;
-					interrupts = <16>;
-					status = "disabled";
-					dmas = <&edma 53 0>, <&edma 57 0>;
-					dma-names = "fifo0", "fifo1";
+			tscadc: tscadc@0 {
+				compatible = "ti,am3359-tscadc";
+				reg = <0x0 0x1000>;
+				interrupts = <16>;
+				clocks = <&adc_tsc_fck>;
+				clock-names = "fck";
+				status = "disabled";
+				dmas = <&edma 53 0>, <&edma 57 0>;
+				dma-names = "fifo0", "fifo1";
 
-					tsc {
-						compatible = "ti,am3359-tsc";
-					};
-					am335x_adc: adc {
-						#io-channel-cells = <1>;
-						compatible = "ti,am3359-adc";
-					};
+				tsc {
+					compatible = "ti,am3359-tsc";
+				};
+				am335x_adc: adc {
+					#io-channel-cells = <1>;
+					compatible = "ti,am3359-adc";
 				};
+			};
 		};
 
 		target-module@10000 {			/* 0x44e10000, ap 22 0c.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0x10000 0x4>;
 			reg-names = "rev";
+			clocks = <&l4_wkup_clkctrl AM3_L4_WKUP_CONTROL_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x00000000 0x00010000 0x00010000>,
@@ -279,7 +302,7 @@
 				am33xx_pinmux: pinmux@800 {
 					compatible = "pinctrl-single";
 					reg = <0x800 0x238>;
-					#pinctrl-cells = <1>;
+					#pinctrl-cells = <2>;
 					pinctrl-single,register-width = <32>;
 					pinctrl-single,function-mask = <0x7f>;
 				};
@@ -331,9 +354,8 @@
 			};
 		};
 
-		target-module@31000 {			/* 0x44e31000, ap 25 40.0 */
+		timer1_target: target-module@31000 {	/* 0x44e31000, ap 25 40.0 */
 			compatible = "ti,sysc-omap2-timer", "ti,sysc";
-			ti,hwmods = "timer1";
 			reg = <0x31000 0x4>,
 			      <0x31010 0x4>,
 			      <0x31014 0x4>;
@@ -415,7 +437,6 @@
 
 		target-module@3e000 {			/* 0x44e3e000, ap 35 60.0 */
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
-			ti,hwmods = "rtc";
 			reg = <0x3e074 0x4>,
 			      <0x3e078 0x4>;
 			reg-names = "rev", "sysc";
@@ -424,6 +445,7 @@
 					<SYSC_IDLE_SMART>,
 					<SYSC_IDLE_SMART_WKUP>;
 			/* Domains (P, C): rtc_pwrdm, l4_rtc_clkdm */
+			power-domains = <&prm_rtc>;
 			clocks = <&l4_rtc_clkctrl AM3_L4_RTC_RTC_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
@@ -433,8 +455,8 @@
 			rtc: rtc@0 {
 				compatible = "ti,am3352-rtc", "ti,da830-rtc";
 				reg = <0x0 0x1000>;
-				interrupts = <75
-					      76>;
+				interrupts = <75>,
+					     <76>;
 			};
 		};
 
@@ -649,7 +671,10 @@
 };
 
 &l4_fast {					/* 0x4a000000 */
-	compatible = "ti,am33xx-l4-fast", "simple-bus";
+	compatible = "ti,am33xx-l4-fast", "simple-pm-bus";
+	power-domains = <&prm_per>;
+	clocks = <&l4hs_clkctrl AM3_L4HS_L4_HS_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4a000000 0x800>,
 	      <0x4a000800 0x800>,
 	      <0x4a001000 0x400>;
@@ -659,7 +684,7 @@
 	ranges = <0x00000000 0x4a000000 0x1000000>;	/* segment 0 */
 
 	segment@0 {					/* 0x4a000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -714,7 +739,7 @@
 				 * c0_tx_pend
 				 * c0_misc_pend
 				 */
-				interrupts = <40 41 42 43>;
+				interrupts = <40>, <41>, <42>, <43>;
 				ranges = <0 0 0x8000>;
 				syscon = <&scm_conf>;
 				status = "disabled";
@@ -742,6 +767,55 @@
 					phys = <&phy_gmii_sel 2 1>;
 				};
 			};
+
+			mac_sw: switch@0 {
+				compatible = "ti,am335x-cpsw-switch", "ti,cpsw-switch";
+				reg = <0x0 0x4000>;
+				ranges = <0 0 0x4000>;
+				clocks = <&cpsw_125mhz_gclk>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				syscon = <&scm_conf>;
+				status = "disabled";
+
+				interrupts = <40>, <41>, <42>, <43>;
+				interrupt-names = "rx_thresh", "rx", "tx", "misc";
+
+				ethernet-ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					cpsw_port1: port@1 {
+						reg = <1>;
+						label = "port1";
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 1 1>;
+					};
+
+					cpsw_port2: port@2 {
+						reg = <2>;
+						label = "port2";
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 2 1>;
+					};
+				};
+
+				davinci_mdio_sw: mdio@1000 {
+					compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+					clocks = <&cpsw_125mhz_gclk>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					bus_freq = <1000000>;
+					reg = <0x1000 0x100>;
+				};
+
+				cpts {
+					clocks = <&cpsw_cpts_rft_clk>;
+					clock-names = "cpts";
+				};
+			};
 		};
 
 		target-module@180000 {			/* 0x4a180000, ap 5 10.0 */
@@ -760,12 +834,109 @@
 			ranges = <0x0 0x200000 0x80000>;
 		};
 
-		target-module@300000 {			/* 0x4a300000, ap 9 04.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+		pruss_tm: target-module@300000 {	/* 0x4a300000, ap 9 04.0 */
+			compatible = "ti,sysc-pruss", "ti,sysc";
+			reg = <0x326000 0x4>,
+			      <0x326004 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <(SYSC_PRUSS_STANDBY_INIT |
+					 SYSC_PRUSS_SUB_MWAIT)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&pruss_ocp_clkctrl AM3_PRUSS_OCP_PRUSS_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_per 1>;
+			reset-names = "rstctrl";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x300000 0x80000>;
+			status = "disabled";
+
+			pruss: pruss@0 {
+				compatible = "ti,am3356-pruss";
+				reg = <0x0 0x80000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				pruss_mem: memories@0 {
+					reg = <0x0 0x2000>,
+					      <0x2000 0x2000>,
+					      <0x10000 0x3000>;
+					reg-names = "dram0", "dram1",
+						    "shrdram2";
+				};
+
+				pruss_cfg: cfg@26000 {
+					compatible = "ti,pruss-cfg", "syscon";
+					reg = <0x26000 0x2000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x26000 0x2000>;
+
+					clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						pruss_iepclk_mux: iepclk-mux@30 {
+							reg = <0x30>;
+							#clock-cells = <0>;
+							clocks = <&l3_gclk>,        /* icss_iep_gclk */
+								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+						};
+					};
+				};
+
+				pruss_mii_rt: mii-rt@32000 {
+					compatible = "ti,pruss-mii", "syscon";
+					reg = <0x32000 0x58>;
+				};
+
+				pruss_intc: interrupt-controller@20000 {
+					compatible = "ti,pruss-intc";
+					reg = <0x20000 0x2000>;
+					interrupts = <20>, <21>, <22>, <23>, <24>, <25>, <26>, <27>;
+					interrupt-names = "host_intr0", "host_intr1",
+							  "host_intr2", "host_intr3",
+							  "host_intr4", "host_intr5",
+							  "host_intr6", "host_intr7";
+					interrupt-controller;
+					#interrupt-cells = <3>;
+				};
+
+				pru0: pru@34000 {
+					compatible = "ti,am3356-pru";
+					reg = <0x34000 0x2000>,
+					      <0x22000 0x400>,
+					      <0x22400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am335x-pru0-fw";
+				};
+
+				pru1: pru@38000 {
+					compatible = "ti,am3356-pru";
+					reg = <0x38000 0x2000>,
+					      <0x24000 0x400>,
+					      <0x24400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am335x-pru1-fw";
+				};
+
+				pruss_mdio: mdio@32400 {
+					compatible = "ti,davinci_mdio";
+					reg = <0x32400 0x90>;
+					clocks = <&dpll_core_m4_ck>;
+					clock-names = "fck";
+					bus_freq = <1000000>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					status = "disabled";
+				};
+			};
 		};
 	};
 };
@@ -813,7 +984,10 @@
 };
 
 &l4_per {						/* 0x48000000 */
-	compatible = "ti,am33xx-l4-per", "simple-bus";
+	compatible = "ti,am33xx-l4-per", "simple-pm-bus";
+	power-domains = <&prm_per>;
+	clocks = <&l4ls_clkctrl AM3_L4LS_L4_LS_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48000000 0x800>,
 	      <0x48000800 0x800>,
 	      <0x48001000 0x400>,
@@ -831,7 +1005,7 @@
 		 <0x46400000 0x46400000 0x400000>;	/* l3 data port */
 
 	segment@0 {					/* 0x48000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -1009,7 +1183,6 @@
 
 		target-module@30000 {			/* 0x48030000, ap 77 08.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi0";
 			reg = <0x30000 0x4>,
 			      <0x30110 0x4>,
 			      <0x30114 0x4>;
@@ -1104,9 +1277,8 @@
 			};
 		};
 
-		target-module@40000 {			/* 0x48040000, ap 22 1e.0 */
+		timer2_target: target-module@40000 {	/* 0x48040000, ap 22 1e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer2";
 			reg = <0x40000 0x4>,
 			      <0x40010 0x4>,
 			      <0x40014 0x4>;
@@ -1134,7 +1306,6 @@
 
 		target-module@42000 {			/* 0x48042000, ap 24 1c.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer3";
 			reg = <0x42000 0x4>,
 			      <0x42010 0x4>,
 			      <0x42014 0x4>;
@@ -1160,7 +1331,6 @@
 
 		target-module@44000 {			/* 0x48044000, ap 26 26.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer4";
 			reg = <0x44000 0x4>,
 			      <0x44010 0x4>,
 			      <0x44014 0x4>;
@@ -1187,7 +1357,6 @@
 
 		target-module@46000 {			/* 0x48046000, ap 28 28.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer5";
 			reg = <0x46000 0x4>,
 			      <0x46010 0x4>,
 			      <0x46014 0x4>;
@@ -1214,7 +1383,6 @@
 
 		target-module@48000 {			/* 0x48048000, ap 30 22.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer6";
 			reg = <0x48000 0x4>,
 			      <0x48010 0x4>,
 			      <0x48014 0x4>;
@@ -1241,7 +1409,6 @@
 
 		target-module@4a000 {			/* 0x4804a000, ap 85 60.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer7";
 			reg = <0x4a000 0x4>,
 			      <0x4a010 0x4>,
 			      <0x4a014 0x4>;
@@ -1290,6 +1457,10 @@
 
 			gpio1: gpio@0 {
 				compatible = "ti,omap4-gpio";
+				gpio-ranges =   <&am33xx_pinmux  0  0  8>,
+						<&am33xx_pinmux  8 90  4>,
+						<&am33xx_pinmux 12 12 16>,
+						<&am33xx_pinmux 28 30  4>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1329,12 +1500,9 @@
 			ranges = <0x0 0x60000 0x1000>;
 
 			mmc1: mmc@0 {
-				compatible = "ti,omap4-hsmmc";
-				ti,dual-volt;
+				compatible = "ti,am335-sdhci";
 				ti,needs-special-reset;
-				ti,needs-special-hs-handling;
-				dmas = <&edma_xbar 24 0 0
-					&edma_xbar 25 0 0>;
+				dmas = <&edma 24 0>, <&edma 25 0>;
 				dma-names = "tx", "rx";
 				interrupts = <64>;
 				reg = <0x0 0x1000>;
@@ -1344,7 +1512,6 @@
 
 		target-module@80000 {			/* 0x48080000, ap 38 18.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "elm";
 			reg = <0x80000 0x4>,
 			      <0x80010 0x4>,
 			      <0x80014 0x4>;
@@ -1402,7 +1569,7 @@
 				#mbox-cells = <1>;
 				ti,mbox-num-users = <4>;
 				ti,mbox-num-fifos = <8>;
-				mbox_wkupm3: wkup_m3 {
+				mbox_wkupm3: mbox-wkup-m3 {
 					ti,mbox-send-noirq;
 					ti,mbox-tx = <0 0 0>;
 					ti,mbox-rx = <0 0 3>;
@@ -1412,7 +1579,6 @@
 
 		target-module@ca000 {			/* 0x480ca000, ap 91 40.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spinlock";
 			reg = <0xca000 0x4>,
 			      <0xca010 0x4>,
 			      <0xca014 0x4>;
@@ -1449,7 +1615,7 @@
 	};
 
 	segment@100000 {					/* 0x48100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0008c000 0x0018c000 0x001000>,	/* ap 42 */
@@ -1533,7 +1699,6 @@
 
 		target-module@a0000 {			/* 0x481a0000, ap 79 24.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi1";
 			reg = <0xa0000 0x4>,
 			      <0xa0110 0x4>,
 			      <0xa0114 0x4>;
@@ -1695,6 +1860,9 @@
 
 			gpio2: gpio@0 {
 				compatible = "ti,omap4-gpio";
+                                gpio-ranges =	<&am33xx_pinmux  0 34 18>,
+						<&am33xx_pinmux 18 77  4>,
+						<&am33xx_pinmux 22 56 10>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1704,7 +1872,7 @@
 			};
 		};
 
-		target-module@ae000 {			/* 0x481ae000, ap 56 3a.0 */
+		gpio3_target: target-module@ae000 {		/* 0x481ae000, ap 56 3a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0xae000 0x4>,
 			      <0xae010 0x4>,
@@ -1728,6 +1896,11 @@
 
 			gpio3: gpio@0 {
 				compatible = "ti,omap4-gpio";
+				gpio-ranges =	<&am33xx_pinmux  0  66 5>,
+						<&am33xx_pinmux  5  98 2>,
+						<&am33xx_pinmux  7  75 2>,
+						<&am33xx_pinmux 13 141 1>,
+						<&am33xx_pinmux 14 100 8>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
@@ -1749,7 +1922,6 @@
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0xcc020 0x4>;
 			reg-names = "rev";
-			ti,hwmods = "d_can0";
 			/* Domains (P, C): per_pwrdm, l4ls_clkdm */
 			clocks = <&l4ls_clkctrl AM3_L4LS_D_CAN0_CLKCTRL 0>,
 				 <&dcan0_fck>;
@@ -1773,7 +1945,6 @@
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0xd0020 0x4>;
 			reg-names = "rev";
-			ti,hwmods = "d_can1";
 			/* Domains (P, C): per_pwrdm, l4ls_clkdm */
 			clocks = <&l4ls_clkctrl AM3_L4LS_D_CAN1_CLKCTRL 0>,
 				 <&dcan1_fck>;
@@ -1815,7 +1986,7 @@
 			ranges = <0x0 0xd8000 0x1000>;
 
 			mmc2: mmc@0 {
-				compatible = "ti,omap4-hsmmc";
+				compatible = "ti,am335-sdhci";
 				ti,needs-special-reset;
 				dmas = <&edma 2 0
 					&edma 3 0>;
@@ -1828,13 +1999,31 @@
 	};
 
 	segment@200000 {					/* 0x48200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
+		ranges = <0x00000000 0x00200000 0x010000>;
+
+		target-module@0 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			power-domains = <&prm_mpu>;
+			clocks = <&mpu_clkctrl AM3_MPU_MPU_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x10000>;
+
+			mpu@0 {
+				compatible = "ti,omap3-mpu";
+				pm-sram = <&pm_sram_code
+					   &pm_sram_data>;
+			};
+		};
 	};
 
 	segment@300000 {					/* 0x48300000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00300000 0x001000>,	/* ap 66 */
@@ -1863,7 +2052,6 @@
 
 		target-module@0 {			/* 0x48300000, ap 66 48.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss0";
 			reg = <0x0 0x4>,
 			      <0x4 0x4>;
 			reg-names = "rev", "sysc";
@@ -1890,21 +2078,26 @@
 				status = "disabled";
 				ranges = <0 0 0x1000>;
 
-				ecap0: ecap@100 {
-					compatible = "ti,am3352-ecap",
-						     "ti,am33xx-ecap";
+				ecap0: pwm@100 {
+					compatible = "ti,am3352-ecap";
 					#pwm-cells = <3>;
 					reg = <0x100 0x80>;
 					clocks = <&l4ls_gclk>;
 					clock-names = "fck";
-					interrupts = <31>;
-					interrupt-names = "ecap0";
+					status = "disabled";
+				};
+
+				eqep0: counter@180 {
+					compatible = "ti,am3352-eqep";
+					reg = <0x180 0x80>;
+					clocks = <&l4ls_gclk>;
+					clock-names = "sysclkout";
+					interrupts = <79>;
 					status = "disabled";
 				};
 
 				ehrpwm0: pwm@200 {
-					compatible = "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+					compatible = "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
@@ -1916,7 +2109,6 @@
 
 		target-module@2000 {			/* 0x48302000, ap 68 52.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss1";
 			reg = <0x2000 0x4>,
 			      <0x2004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1943,21 +2135,26 @@
 				status = "disabled";
 				ranges = <0 0 0x1000>;
 
-				ecap1: ecap@100 {
-					compatible = "ti,am3352-ecap",
-						     "ti,am33xx-ecap";
+				ecap1: pwm@100 {
+					compatible = "ti,am3352-ecap";
 					#pwm-cells = <3>;
 					reg = <0x100 0x80>;
 					clocks = <&l4ls_gclk>;
 					clock-names = "fck";
-					interrupts = <47>;
-					interrupt-names = "ecap1";
+					status = "disabled";
+				};
+
+				eqep1: counter@180 {
+					compatible = "ti,am3352-eqep";
+					reg = <0x180 0x80>;
+					clocks = <&l4ls_gclk>;
+					clock-names = "sysclkout";
+					interrupts = <88>;
 					status = "disabled";
 				};
 
 				ehrpwm1: pwm@200 {
-					compatible = "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+					compatible = "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
@@ -1969,7 +2166,6 @@
 
 		target-module@4000 {			/* 0x48304000, ap 70 44.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss2";
 			reg = <0x4000 0x4>,
 			      <0x4004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1996,21 +2192,26 @@
 				status = "disabled";
 				ranges = <0 0 0x1000>;
 
-				ecap2: ecap@100 {
-					compatible = "ti,am3352-ecap",
-						     "ti,am33xx-ecap";
+				ecap2: pwm@100 {
+					compatible = "ti,am3352-ecap";
 					#pwm-cells = <3>;
 					reg = <0x100 0x80>;
 					clocks = <&l4ls_gclk>;
 					clock-names = "fck";
-					interrupts = <61>;
-					interrupt-names = "ecap2";
+					status = "disabled";
+				};
+
+				eqep2: counter@180 {
+					compatible = "ti,am3352-eqep";
+					reg = <0x180 0x80>;
+					clocks = <&l4ls_gclk>;
+					clock-names = "sysclkout";
+					interrupts = <89>;
 					status = "disabled";
 				};
 
 				ehrpwm2: pwm@200 {
-					compatible = "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+					compatible = "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
@@ -2022,7 +2223,6 @@
 
 		target-module@e000 {			/* 0x4830e000, ap 72 4a.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "lcdc";
 			reg = <0xe000 0x4>,
 			      <0xe054 0x4>;
 			reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/ti/omap/am33xx.dtsi b/arch/arm/boot/dts/ti/omap/am33xx.dtsi
new file mode 100644
index 000000000000..5b9e01a8aa5d
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am33xx.dtsi
@@ -0,0 +1,725 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree Source for AM33XX SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/am33xx.h>
+#include <dt-bindings/clock/am3.h>
+
+/ {
+	compatible = "ti,am33xx";
+	interrupt-parent = <&intc>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+		serial5 = &uart5;
+		d-can0 = &dcan0;
+		d-can1 = &dcan1;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		phy0 = &usb0_phy;
+		phy1 = &usb1_phy;
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		mmc0 = &mmc1;
+		mmc1 = &mmc2;
+		mmc2 = &mmc3;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			compatible = "arm,cortex-a8";
+			enable-method = "ti,am3352";
+			device_type = "cpu";
+			reg = <0>;
+
+			operating-points-v2 = <&cpu0_opp_table>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+			cpu-idle-states = <&mpu_gate>;
+		};
+
+		idle-states {
+			mpu_gate: mpu_gate {
+				compatible = "arm,idle-state";
+				entry-latency-us = <40>;
+				exit-latency-us = <90>;
+				min-residency-us = <300>;
+				ti,idle-wkup-m3;
+			};
+		};
+	};
+
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		syscon = <&scm_conf>;
+
+		/*
+		 * The three following nodes are marked with opp-suspend
+		 * because the can not be enabled simultaneously on a
+		 * single SoC.
+		 */
+		opp-50-300000000{
+			/* OPP50 */
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <950000 931000 969000>;
+			opp-supported-hw = <0x06 0x0010>;
+			opp-suspend;
+		};
+
+		opp-100-275000000{
+			/* OPP100-1 */
+			opp-hz = /bits/ 64 <275000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x01 0x00FF>;
+			opp-suspend;
+		};
+
+		opp-100-300000000{
+			/* OPP100-2 */
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x06 0x0020>;
+			opp-suspend;
+		};
+
+		opp-100-500000000{
+			/* OPP100-3 */
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x01 0xFFFF>;
+		};
+
+		opp-100-600000000 {
+			/* OPP100-4 */
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0x06 0x0040>;
+		};
+
+		opp-120-600000000 {
+			/* OPP120-1 */
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1200000 1176000 1224000>;
+			opp-supported-hw = <0x01 0xFFFF>;
+		};
+
+		opp-120-720000000 {
+			/* OPP120-2 */
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1200000 1176000 1224000>;
+			opp-supported-hw = <0x06 0x0080>;
+		};
+
+		opp-720000000 {
+			/* OPP Turbo-1 */
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1260000 1234800 1285200>;
+			opp-supported-hw = <0x01 0xFFFF>;
+		};
+
+		opp-800000000 {
+			/* OPP Turbo-2 */
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1260000 1234800 1285200>;
+			opp-supported-hw = <0x06 0x0100>;
+		};
+
+		opp-1000000000 {
+			/* OPP Nitro */
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1325000 1298500 1351500>;
+			opp-supported-hw = <0x04 0x0200>;
+		};
+	};
+
+	target-module@4b000000 {
+		compatible = "ti,sysc-omap4-simple", "ti,sysc";
+		clocks = <&l3_clkctrl AM3_L3_L3_INSTR_CLKCTRL 0>;
+		clock-names = "fck";
+		ti,no-idle;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x4b000000 0x1000000>;
+
+		target-module@140000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			clocks = <&l3_aon_clkctrl AM3_L3_AON_DEBUGSS_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x140000 0xec0000>;
+
+			pmu@0 {
+				compatible = "arm,cortex-a8-pmu";
+				interrupts = <3>;
+			};
+		};
+	};
+
+	/*
+	 * The soc node represents the soc top level view. It is used for IPs
+	 * that are not memory mapped in the MPU view or for the MPU itself.
+	 */
+	soc {
+		compatible = "ti,omap-infra";
+	};
+
+	/*
+	 * XXX: Use a flat representation of the AM33XX interconnect.
+	 * The real AM33XX interconnect network is quite complex. Since
+	 * it will not bring real advantage to represent that in DT
+	 * for the moment, just use a fake OCP bus entry to represent
+	 * the whole bus hierarchy.
+	 */
+	ocp: ocp {
+		compatible = "simple-pm-bus";
+		power-domains = <&prm_per>;
+		clocks = <&l3_clkctrl AM3_L3_L3_MAIN_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		l4_wkup: interconnect@44c00000 {
+		};
+		l4_per: interconnect@48000000 {
+		};
+		l4_fw: interconnect@47c00000 {
+		};
+		l4_fast: interconnect@4a000000 {
+		};
+		l4_mpuss: interconnect@4b140000 {
+		};
+
+		intc: interrupt-controller@48200000 {
+			compatible = "ti,am33xx-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x48200000 0x1000>;
+		};
+
+		target-module@49000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49000000 0x4>;
+			reg-names = "rev";
+			clocks = <&l3_clkctrl AM3_L3_TPCC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49000000 0x10000>;
+
+			edma: dma@0 {
+				compatible = "ti,edma3-tpcc";
+				reg = <0 0x10000>;
+				reg-names = "edma3_cc";
+				interrupts = <12 13 14>;
+				interrupt-names = "edma3_ccint", "edma3_mperr",
+						  "edma3_ccerrint";
+				dma-requests = <64>;
+				#dma-cells = <2>;
+
+				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
+					   <&edma_tptc2 0>;
+
+				ti,edma-memcpy-channels = <20 21>;
+			};
+		};
+
+		target-module@49800000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49800000 0x4>,
+			      <0x49800010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3_clkctrl AM3_L3_TPTC0_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49800000 0x100000>;
+
+			edma_tptc0: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <112>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49900000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49900000 0x4>,
+			      <0x49900010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3_clkctrl AM3_L3_TPTC1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49900000 0x100000>;
+
+			edma_tptc1: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <113>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49a00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49a00000 0x4>,
+			      <0x49a00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3_clkctrl AM3_L3_TPTC2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49a00000 0x100000>;
+
+			edma_tptc2: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <114>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@47810000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x478102fc 0x4>,
+			      <0x47810110 0x4>,
+			      <0x47810114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&l3s_clkctrl AM3_L3S_MMC3_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x47810000 0x1000>;
+
+			mmc3: mmc@0 {
+				compatible = "ti,am335-sdhci";
+				ti,needs-special-reset;
+				interrupts = <29>;
+				reg = <0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		usb: target-module@47400000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x47400000 0x4>,
+			      <0x47400010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <(SYSC_OMAP4_FREEEMU |
+					 SYSC_OMAP4_SOFTRESET)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-delay-us = <2>;
+			clocks = <&l3s_clkctrl AM3_L3S_USB_OTG_HS_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x47400000 0x8000>;
+
+			usb0_phy: usb-phy@1300 {
+				compatible = "ti,am335x-usb-phy";
+				reg = <0x1300 0x100>;
+				reg-names = "phy";
+				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
+			};
+
+			usb0: usb@1400 {
+				compatible = "ti,musb-am33xx";
+				reg = <0x1400 0x400>,
+				      <0x1000 0x200>;
+				reg-names = "mc", "control";
+
+				interrupts = <18>;
+				interrupt-names = "mc";
+				dr_mode = "otg";
+				mentor,multipoint = <1>;
+				mentor,num-eps = <16>;
+				mentor,ram-bits = <12>;
+				mentor,power = <500>;
+				phys = <&usb0_phy>;
+
+				dmas = <&cppi41dma  0 0 &cppi41dma  1 0
+					&cppi41dma  2 0 &cppi41dma  3 0
+					&cppi41dma  4 0 &cppi41dma  5 0
+					&cppi41dma  6 0 &cppi41dma  7 0
+					&cppi41dma  8 0 &cppi41dma  9 0
+					&cppi41dma 10 0 &cppi41dma 11 0
+					&cppi41dma 12 0 &cppi41dma 13 0
+					&cppi41dma 14 0 &cppi41dma  0 1
+					&cppi41dma  1 1 &cppi41dma  2 1
+					&cppi41dma  3 1 &cppi41dma  4 1
+					&cppi41dma  5 1 &cppi41dma  6 1
+					&cppi41dma  7 1 &cppi41dma  8 1
+					&cppi41dma  9 1 &cppi41dma 10 1
+					&cppi41dma 11 1 &cppi41dma 12 1
+					&cppi41dma 13 1 &cppi41dma 14 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			usb1_phy: usb-phy@1b00 {
+				compatible = "ti,am335x-usb-phy";
+				reg = <0x1b00 0x100>;
+				reg-names = "phy";
+				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
+			};
+
+			usb1: usb@1800 {
+				compatible = "ti,musb-am33xx";
+				reg = <0x1c00 0x400>,
+				      <0x1800 0x200>;
+				reg-names = "mc", "control";
+				interrupts = <19>;
+				interrupt-names = "mc";
+				dr_mode = "otg";
+				mentor,multipoint = <1>;
+				mentor,num-eps = <16>;
+				mentor,ram-bits = <12>;
+				mentor,power = <500>;
+				phys = <&usb1_phy>;
+
+				dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+					&cppi41dma 17 0 &cppi41dma 18 0
+					&cppi41dma 19 0 &cppi41dma 20 0
+					&cppi41dma 21 0 &cppi41dma 22 0
+					&cppi41dma 23 0 &cppi41dma 24 0
+					&cppi41dma 25 0 &cppi41dma 26 0
+					&cppi41dma 27 0 &cppi41dma 28 0
+					&cppi41dma 29 0 &cppi41dma 15 1
+					&cppi41dma 16 1 &cppi41dma 17 1
+					&cppi41dma 18 1 &cppi41dma 19 1
+					&cppi41dma 20 1 &cppi41dma 21 1
+					&cppi41dma 22 1 &cppi41dma 23 1
+					&cppi41dma 24 1 &cppi41dma 25 1
+					&cppi41dma 26 1 &cppi41dma 27 1
+					&cppi41dma 28 1 &cppi41dma 29 1>;
+				dma-names =
+					"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+					"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+					"rx14", "rx15",
+					"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+					"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+					"tx14", "tx15";
+			};
+
+			cppi41dma: dma-controller@2000 {
+				compatible = "ti,am3359-cppi41";
+				reg =  <0x0000 0x1000>,
+				       <0x2000 0x1000>,
+				       <0x3000 0x1000>,
+				       <0x4000 0x4000>;
+				reg-names = "glue", "controller", "scheduler", "queuemgr";
+				interrupts = <17>;
+				interrupt-names = "glue";
+				#dma-cells = <2>;
+				/* For backwards compatibility: */
+				#dma-channels = <30>;
+				dma-channels = <30>;
+				#dma-requests = <256>;
+				dma-requests = <256>;
+			};
+		};
+
+		target-module@40300000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			clocks = <&l3_clkctrl AM3_L3_OCMCRAM_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40300000 0x10000>;
+
+			ocmcram: sram@0 {
+				compatible = "mmio-sram";
+				reg = <0 0x10000>; /* 64k */
+				ranges = <0 0 0x10000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				pm_sram_code: pm-code-sram@0 {
+					compatible = "ti,sram";
+					reg = <0x0 0x1000>;
+					protect-exec;
+				};
+
+				pm_sram_data: pm-data-sram@1000 {
+					compatible = "ti,sram";
+					reg = <0x1000 0x1000>;
+					pool;
+				};
+			};
+		};
+
+		target-module@4c000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			reg = <0x4c000000 0x4>;
+			reg-names = "rev";
+			clocks = <&l3_clkctrl AM3_L3_EMIF_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4c000000 0x1000000>;
+
+			emif: emif@0 {
+				compatible = "ti,emif-am3352";
+				reg = <0 0x1000000>;
+				interrupts = <101>;
+				sram = <&pm_sram_code
+					&pm_sram_data>;
+			};
+		};
+
+		target-module@50000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x50000000 4>,
+			      <0x50000010 4>,
+			      <0x50000014 4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&l3s_clkctrl AM3_L3S_GPMC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
+				 <0x00000000 0x00000000 0x40000000>; /* data */
+
+			gpmc: gpmc@50000000 {
+				compatible = "ti,am3352-gpmc";
+				reg = <0x50000000 0x2000>;
+				interrupts = <100>;
+				dmas = <&edma 52 0>;
+				dma-names = "rxtx";
+				gpmc,num-cs = <7>;
+				gpmc,num-waitpins = <2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		sham_target: target-module@53100000 {
+			compatible = "ti,sysc-omap3-sham", "ti,sysc";
+			reg = <0x53100100 0x4>,
+			      <0x53100110 0x4>,
+			      <0x53100114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l3_clkdm */
+			clocks = <&l3_clkctrl AM3_L3_SHAM_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x53100000 0x1000>;
+
+			sham: sham@0 {
+				compatible = "ti,omap4-sham";
+				reg = <0 0x200>;
+				interrupts = <109>;
+				dmas = <&edma 36 0>;
+				dma-names = "rx";
+			};
+		};
+
+		aes_target: target-module@53500000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x53500080 0x4>,
+			      <0x53500084 0x4>,
+			      <0x53500088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l3_clkdm */
+			clocks = <&l3_clkctrl AM3_L3_AES_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x53500000 0x1000>;
+
+			aes: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <103>;
+				dmas = <&edma 6 0>,
+				       <&edma 5 0>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		target-module@56000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5600fe00 0x4>,
+			      <0x5600fe10 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&gfx_l3_clkctrl AM3_GFX_L3_GFX_CLKCTRL 0>;
+			clock-names = "fck";
+			power-domains = <&prm_gfx>;
+			resets = <&prm_gfx 0>;
+			reset-names = "rstctrl";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x56000000 0x1000000>;
+
+			/*
+			 * Closed source PowerVR driver, no child device
+			 * binding or driver in mainline
+			 */
+		};
+	};
+};
+
+#include "am33xx-l4.dtsi"
+#include "am33xx-clocks.dtsi"
+
+&prcm {
+	prm_per: prm@c00 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0xc00 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_wkup: prm@d00 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0xd00 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_mpu: prm@e00 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0xe00 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_device: prm@f00 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0xf00 0x100>;
+		#reset-cells = <1>;
+	};
+
+	prm_rtc: prm@1000 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1000 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_gfx: prm@1100 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1100 0x100>;
+		#power-domain-cells = <0>;
+		#reset-cells = <1>;
+	};
+
+	prm_cefuse: prm@1200 {
+		compatible = "ti,am3-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1200 0x100>;
+		#power-domain-cells = <0>;
+	};
+};
+
+/* Preferred always-on timer for clocksource */
+&timer1_target {
+	clocks = <&l4_wkup_clkctrl AM3_L4_WKUP_TIMER1_CLKCTRL 0>,
+		 <&l4_wkup_clkctrl AM3_L4_WKUP_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck", "ick";
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer1_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	clocks = <&l4ls_clkctrl AM3_L4LS_TIMER2_CLKCTRL 0>,
+		 <&l4ls_clkctrl AM3_L4LS_L4_LS_CLKCTRL 0>;
+	clock-names = "fck", "ick";
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer2_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/am3517-craneboard.dts b/arch/arm/boot/dts/ti/omap/am3517-craneboard.dts
index eb3517dabee1..d035c888731f 100644
--- a/arch/arm/boot/dts/am3517-craneboard.dts
+++ b/arch/arm/boot/dts/ti/omap/am3517-craneboard.dts
@@ -2,7 +2,7 @@
 /*
  * See craneboard.org for more details
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -69,10 +69,10 @@
 	status = "disabled";
 };
 
-#include "tps65910.dtsi"
+#include "../../tps65910.dtsi"
 
 &omap3_pmx_core {
-	tps_pins: pinmux_tps_pins {
+	tps_pins: tps-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21e0, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */
 		>;
diff --git a/arch/arm/boot/dts/am3517-evm-ui.dtsi b/arch/arm/boot/dts/ti/omap/am3517-evm-ui.dtsi
index 48631a45da51..16b8968d5be8 100644
--- a/arch/arm/boot/dts/am3517-evm-ui.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am3517-evm-ui.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2018 Logic PD, Inc - http://www.logicpd.com/
+ * Copyright (C) 2018 Logic PD, Inc - https://www.logicpd.com/
  */
 
 #include <dt-bindings/input/input.h>
@@ -70,61 +70,61 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <100>;
 
-		record {
+		key-record {
 			label = "Record";
 			/* linux,code = <BTN_0>; */
 			gpios = <&tca6416_2 15 GPIO_ACTIVE_LOW>;
 		};
 
-		play {
+		key-play {
 			label = "Play";
 			linux,code = <KEY_PLAY>;
 			gpios = <&tca6416_2 14 GPIO_ACTIVE_LOW>;
 		};
 
-		Stop {
+		key-stop {
 			label = "Stop";
 			linux,code = <KEY_STOP>;
 			gpios = <&tca6416_2 13 GPIO_ACTIVE_LOW>;
 		};
 
-		fwd {
+		key-fwd {
 			label = "FWD";
 			linux,code = <KEY_FASTFORWARD>;
 			gpios = <&tca6416_2 12 GPIO_ACTIVE_LOW>;
 		};
 
-		rwd {
+		key-rwd {
 			label = "RWD";
 			linux,code = <KEY_REWIND>;
 			gpios = <&tca6416_2 11 GPIO_ACTIVE_LOW>;
 		};
 
-		shift {
+		key-shift {
 			label = "Shift";
 			linux,code = <KEY_LEFTSHIFT>;
 			gpios = <&tca6416_2 10 GPIO_ACTIVE_LOW>;
 		};
 
-		Mode {
+		key-mode {
 			label = "Mode";
 			linux,code = <BTN_MODE>;
 			gpios = <&tca6416_2 9 GPIO_ACTIVE_LOW>;
 		};
 
-		Menu {
+		key-menu {
 			label = "Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&tca6416_2 8 GPIO_ACTIVE_LOW>;
 		};
 
-		Up {
+		key-up {
 			label = "Up";
 			linux,code = <KEY_UP>;
 			gpios = <&tca6416_2 7 GPIO_ACTIVE_LOW>;
 		};
 
-		Down {
+		key-down {
 			label = "Down";
 			linux,code = <KEY_DOWN>;
 			gpios = <&tca6416_2 6 GPIO_ACTIVE_LOW>;
@@ -137,14 +137,14 @@
 	tlv320aic23_1: codec@1a {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1a>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 
 	tlv320aic23_2: codec@1b {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1b>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 };
@@ -154,7 +154,7 @@
 	tlv320aic23_3: codec@1a {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1a>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 
@@ -183,21 +183,21 @@
 };
 
 &mcbsp1 {
-	status = "ok";
+	status = "okay";
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp1_pins>;
 };
 
 &mcbsp2 {
-	status = "ok";
+	status = "okay";
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
 };
 
 &omap3_pmx_core {
-	mcbsp1_pins: pinmux_mcbsp1_pins {
+	mcbsp1_pins: mcbsp1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE0)	/* mcbsp1_dx.mcbsp1_dx */
 			OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT | MUX_MODE0)	/* mcbsp1_dx.mcbsp1_dr */
@@ -206,7 +206,7 @@
 		>;
 	};
 
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx.mcbsp2_fsx */
 			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)	/* mcbsp2_clkx.mcbsp2_clkx */
diff --git a/arch/arm/boot/dts/am3517-evm.dts b/arch/arm/boot/dts/ti/omap/am3517-evm.dts
index a1fd3e63e86e..40f15da81043 100644
--- a/arch/arm/boot/dts/am3517-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am3517-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -26,66 +26,66 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-        vmmc_fixed: vmmc {
-                compatible = "regulator-fixed";
-                regulator-name = "vmmc_fixed";
-                regulator-min-microvolt = <3300000>;
-                regulator-max-microvolt = <3300000>;
-        };
+	vmmc_fixed: vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
 	gpio-keys {
 		compatible = "gpio-keys-polled";
 		poll-interval = <100>;
 
-		user_pb {
+		button-user {
 			label = "User Push Button";
 			linux,code = <BTN_0>;
 			gpios = <&tca6416 5 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_1 {
+		switch-1 {
 			label = "User Switch 1";
 			linux,code = <BTN_1>;
 			gpios = <&tca6416 8 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_2 {
+		switch-2 {
 			label = "User Switch 2";
 			linux,code = <BTN_2>;
 			gpios = <&tca6416 9 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_3 {
+		switch-3 {
 			label = "User Switch 3";
 			linux,code = <BTN_3>;
 			gpios = <&tca6416 10 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_4 {
+		switch-4 {
 			label = "User Switch 4";
 			linux,code = <BTN_4>;
 			gpios = <&tca6416 11 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_5 {
+		switch-5 {
 			label = "User Switch 5";
 			linux,code = <BTN_5>;
 			gpios = <&tca6416 12 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_6 {
+		switch-6 {
 			label = "User Switch 6";
 			linux,code = <BTN_6>;
 			gpios = <&tca6416 13 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_7 {
+		switch-7 {
 			label = "User Switch 7";
 			linux,code = <BTN_7>;
 			gpios = <&tca6416 14 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_8 {
+		switch-8 {
 			label = "User Switch 8";
 			linux,code = <BTN_8>;
 			gpios = <&tca6416 15 GPIO_ACTIVE_LOW>;
@@ -150,16 +150,19 @@
 		enable-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* gpio_182 */
 	};
 
-	pwm11: dmtimer-pwm@11 {
+	pwm11: pwm-11 {
 		compatible = "ti,omap-dmtimer-pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm_pins>;
 		ti,timers = <&timer11>;
 		#pwm-cells = <3>;
+		ti,clock-source = <0x01>;
 	};
 
 	/* HS USB Host PHY on PORT 1 */
 	hsusb1_phy: hsusb1_phy {
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb1_rst_pins>;
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; /* gpio_57 */
 		#phy-cells = <0>;
@@ -167,15 +170,30 @@
 };
 
 &davinci_emac {
-	     status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
 };
 
 &davinci_mdio {
-	     status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&enet_phy_pins>;
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;	/* gpio_58 */
+	};
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
@@ -192,6 +210,8 @@
 };
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 	/* User DIP swithes [1:8] / User LEDS [1:2] */
 	tca6416: gpio@21 {
@@ -204,6 +224,8 @@
 };
 
 &i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
 };
 
@@ -218,10 +240,12 @@
 };
 
 &mmc3 {
-      status = "disabled";
+	status = "disabled";
 };
 
 &usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_pins>;
 	port1-mode = "ehci-phy";
 };
 
@@ -230,17 +254,43 @@
 };
 
 &omap3_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb1_rst_pins>;
 
-	leds_pins: pinmux_leds_pins {
+	ethernet_pins: ethernet-pins {
 		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
-			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
+			OMAP3_CORE1_IOPAD(0x21fe, PIN_INPUT | MUX_MODE0) /* rmii_mdio_data */
+			OMAP3_CORE1_IOPAD(0x2200, MUX_MODE0) /* rmii_mdio_clk */
+			OMAP3_CORE1_IOPAD(0x2202, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd0 */
+			OMAP3_CORE1_IOPAD(0x2204, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd1 */
+			OMAP3_CORE1_IOPAD(0x2206, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_crs_dv */
+			OMAP3_CORE1_IOPAD(0x2208, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_rxer */
+			OMAP3_CORE1_IOPAD(0x220a, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd0 */
+			OMAP3_CORE1_IOPAD(0x220c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd1 */
+			OMAP3_CORE1_IOPAD(0x220e, PIN_OUTPUT_PULLDOWN |MUX_MODE0) /* rmii_txen */
+			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	enet_phy_pins: ethernet-phy-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20bc, PIN_INPUT | MUX_MODE4)	/* gpmc_ncs7.gpio_57 */
+		>;
+	};
+
+	i2c2_pins: i2c2-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_scl */
+			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: i2c3-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_scl */
+			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_sda */
+		>;
+	};
+
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -253,19 +303,19 @@
 		>;
 	};
 
-	pwm_pins: pinmux_pwm_pins {
+	pwm_pins: pwm-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE1)       /* mcspi2_cs0.gpt11_pwm */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT | MUX_MODE4)       /* mcspi2_cs1.gpio_182 */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_OUTPUT | MUX_MODE4)       /* mcspi1_cs2.gpio_176 */
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)       /* dss_pclk.dss_pclk */
@@ -291,7 +341,7 @@
 		>;
 	};
 
-	hsusb1_rst_pins: pinmux_hsusb1_rst_pins {
+	hsusb1_rst_pins: hsusb1-rst-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs6.gpio_57 */
 		>;
@@ -299,10 +349,8 @@
 };
 
 &omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb1_pins>;
 
-	hsusb1_pins: pinmux_hsusb1_pins {
+	hsusb1_pins: hsusb1-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3)	/* etk_clk.hsusb1_stp */
 			OMAP3430_CORE2_IOPAD(0x25da, PIN_OUTPUT | MUX_MODE3)	/* etk_ctl.hsusb1_clk */
@@ -319,3 +367,12 @@
 		>;
 	};
 };
+
+&omap3_pmx_wkup {
+	leds_pins: leds-pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
+			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/am3517-som.dtsi b/arch/arm/boot/dts/ti/omap/am3517-som.dtsi
index 8b669e2eafec..bd0a6c95afa1 100644
--- a/arch/arm/boot/dts/am3517-som.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am3517-som.dtsi
@@ -69,6 +69,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <400000>;
 
 	s35390a: s35390a@30 {
@@ -179,13 +181,20 @@
 
 &omap3_pmx_core {
 
-	wl12xx_buffer_pins: pinmux_wl12xx_buffer_pins {
+	i2c1_pins: i2c1-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c1_scl */
+			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c1_sda */
+		>;
+	};
+
+	wl12xx_buffer_pins: wl12xx-buffer-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4)  /* mmc1_dat7.gpio_129 */
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_clk.mmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc2_cmd.mmc2_cmd */
@@ -201,19 +210,19 @@
 		>;
 	};
 
-	rtc_pins: pinmux_rtc_pins {
+	rtc_pins: rtc-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */
 		>;
 	};
 
-	tsc2004_pins: pinmux_tsc2004_pins {
+	tsc2004_pins: tsc2004-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)		/* uart2_cts */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* uart2_rts */
@@ -226,7 +235,7 @@
 
 &omap3_pmx_wkup {
 
-	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+	wl12xx_wkup_pins: wl12xx-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 		>;
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/ti/omap/am3517.dtsi
index 125379ecab2f..77e58e686fb1 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am3517.dtsi
@@ -1,19 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for am3517 SoC
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "omap3.dtsi"
 
+/* AM3517 doesn't appear to have the crypto engines defined in omap3.dtsi */
+/delete-node/ &aes1_target;
+/delete-node/ &aes2_target;
+
 / {
 	aliases {
 		serial3 = &uart4;
 		can = &hecc;
+		ethernet = &davinci_emac;
 	};
 
 	cpus {
@@ -33,14 +35,16 @@
 		 * appear to operate at 300MHz as well. Since AM3517 only
 		 * lists one operating voltage, it will remain fixed at 1.2V
 		 */
-		opp50-300000000 {
+		opp-50-300000000 {
+			/* OPP50 */
 			opp-hz = /bits/ 64 <300000000>;
 			opp-microvolt = <1200000>;
 			opp-supported-hw = <0xffffffff 0xffffffff>;
 			opp-suspend;
 		};
 
-		opp100-600000000 {
+		opp-100-600000000 {
+			/* OPP100 */
 			opp-hz = /bits/ 64 <600000000>;
 			opp-microvolt = <1200000>;
 			opp-supported-hw = <0xffffffff 0xffffffff>;
@@ -48,13 +52,35 @@
 	};
 
 	ocp@68000000 {
-		am35x_otg_hs: am35x_otg_hs@5c040000 {
-			compatible = "ti,omap3-musb";
-			ti,hwmods = "am35x_otg_hs";
-			status = "disabled";
-			reg = <0x5c040000 0x1000>;
-			interrupts = <71>;
-			interrupt-names = "mc";
+		target-module@5c040000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x5c040400 0x4>,
+			      <0x5c040404 0x4>,
+			      <0x5c040408 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&hsotgusb_ick_am35xx>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x5c040000 0x1000>;
+
+			am35x_otg_hs: am35x_otg_hs@0 {
+				compatible = "ti,omap3-musb";
+				status = "disabled";
+				reg = <0 0x1000>;
+				interrupts = <71>;
+				interrupt-names = "mc";
+			};
 		};
 
 		davinci_emac: ethernet@5c000000 {
@@ -74,7 +100,7 @@
 			clock-names = "ick";
 		};
 
-		davinci_mdio: ethernet@5c030000 {
+		davinci_mdio: mdio@5c030000 {
 			compatible = "ti,davinci_mdio";
 			ti,hwmods = "davinci_mdio";
 			status = "disabled";
@@ -153,7 +179,7 @@
 };
 
 /* Table Table 5-79 of the TRM shows 480ab000 is reserved */
-&usb_otg_hs {
+&usb_otg_target {
 	status = "disabled";
 };
 
@@ -169,5 +195,25 @@
 	status = "disabled";
 };
 
-/include/ "am35xx-clocks.dtsi"
-/include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
+#include "am35xx-clocks.dtsi"
+#include "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
+
+/* Preferred always-on timer for clocksource */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt1_fck>;
+		assigned-clock-parents = <&sys_ck>;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt2_fck>;
+		assigned-clock-parents = <&sys_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/am3517_mt_ventoux.dts b/arch/arm/boot/dts/ti/omap/am3517_mt_ventoux.dts
index e7d7124a34ba..e7d7124a34ba 100644
--- a/arch/arm/boot/dts/am3517_mt_ventoux.dts
+++ b/arch/arm/boot/dts/ti/omap/am3517_mt_ventoux.dts
diff --git a/arch/arm/boot/dts/am35xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/am35xx-clocks.dtsi
index 220d0a52797e..0ee7afaa0e8e 100644
--- a/arch/arm/boot/dts/am35xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am35xx-clocks.dtsi
@@ -62,12 +62,27 @@
 	};
 };
 &cm_clocks {
-	ipss_ick: ipss_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,am35xx-interface-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <4>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ipss_ick: clock-ipss-ick {
+			#clock-cells = <0>;
+			compatible = "ti,am35xx-interface-clock";
+			clock-output-names = "ipss_ick";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		uart4_ick_am35xx: clock-uart4-ick-am35xx {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart4_ick_am35xx";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <23>;
+		};
 	};
 
 	rmii_ck: rmii_ck {
@@ -82,20 +97,19 @@
 		clock-frequency = <27000000>;
 	};
 
-	uart4_ick_am35xx: uart4_ick_am35xx@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <23>;
-	};
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	uart4_fck_am35xx: uart4_fck_am35xx@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <23>;
+		uart4_fck_am35xx: clock-uart4-fck-am35xx {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart4_fck_am35xx";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <23>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/ti/omap/am3703.dtsi b/arch/arm/boot/dts/ti/omap/am3703.dtsi
new file mode 100644
index 000000000000..2b994ae790c9
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am3703.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2020 André Hentschel <nerv@dawncrow.de>
+ */
+
+#include "omap36xx.dtsi"
+
+&iva {
+	status = "disabled";
+};
+
+&sgx_module {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/ti/omap/am3715.dtsi b/arch/arm/boot/dts/ti/omap/am3715.dtsi
new file mode 100644
index 000000000000..ab328e8c0bd8
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am3715.dtsi
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2020 André Hentschel <nerv@dawncrow.de>
+ */
+
+#include "omap36xx.dtsi"
+
+&iva {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am3874-iceboard.dts b/arch/arm/boot/dts/ti/omap/am3874-iceboard.dts
index 1b4b2b0500e4..ac082e83a9a2 100644
--- a/arch/arm/boot/dts/am3874-iceboard.dts
+++ b/arch/arm/boot/dts/ti/omap/am3874-iceboard.dts
@@ -2,8 +2,8 @@
 /*
  * Device tree for Winterland IceBoard
  *
- * http://mcgillcosmology.com
- * http://threespeedlogic.com
+ * https://mcgillcosmology.com
+ * https://threespeedlogic.com
  *
  * This is an ARM + FPGA instrumentation board used at telescopes in
  * Antarctica (the South Pole Telescope), Chile (POLARBEAR), and at the DRAO
@@ -106,7 +106,7 @@
 	 * "i2c-mux-idle-disconnect" is important.
 	 */
 
-	pca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -195,7 +195,7 @@
 					"FMCA_PG_C2M", "FMCA_PRSNT_M2C_L", "FMCA_CLK_DIR", "SFP_LOS",
 					"FMCB_EN_12V0", "FMCB_EN_3V3", "FMCB_EN_VADJ", "FMCB_PG_M2C",
 					"FMCB_PG_C2M", "FMCB_PRSNT_M2C_L", "FMCB_CLK_DIR", "SFP_ModPrsL";
-				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 			};
 
 			u42: pca9575@21 {
@@ -208,12 +208,12 @@
 					"QSFPA_LPMode", "QSFPB_ModPrsL", "QSFPB_IntL", "QSFPB_ResetL",
 					"SFP_TxFault", "SFP_TxDisable", "SFP_RS0", "SFP_RS1",
 					"QSFPB_ModSelL", "QSFPB_LPMode", "SEL_SFP", "ARM_MR";
-				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 			};
 
 			u48: pca9575@22 {
 				compatible = "nxp,pca9575";
-				reg=<0x22>;
+				reg = <0x22>;
 				gpio-controller;
 				#gpio-cells = <2>;
 
@@ -227,12 +227,12 @@
 					"GP_SW5", "GP_SW6", "GP_SW7", "GP_SW8",
 					"GP_LED8", "GP_LED7", "GP_LED6", "GP_LED5",
 					"GP_LED4", "GP_LED3", "GP_LED2", "GP_LED1";
-				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 			};
 
 			u59: pca9575@23 {
 				compatible = "nxp,pca9575";
-				reg=<0x23>;
+				reg = <0x23>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				gpio-line-names =
@@ -240,7 +240,7 @@
 					"GTX1V8PowerFault", "PHYAPowerFault", "PHYBPowerFault", "ArmPowerFault",
 					"BP_SLOW_GPIO0", "BP_SLOW_GPIO1", "BP_SLOW_GPIO2", "BP_SLOW_GPIO3",
 					"BP_SLOW_GPIO4", "BP_SLOW_GPIO5", "__unused_u59_p16", "__unused_u59_p17";
-				reset_gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 			};
 
 			tmp100@48 { compatible = "ti,tmp100"; reg = <0x48>; };
@@ -256,7 +256,7 @@
 };
 
 &i2c2 {
-	pca9548@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -285,7 +285,7 @@
 };
 
 &pincntl {
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0800, PIN_INPUT | 0x1)	/* SD1_CLK */
 			DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1)	/* SD1_CMD */
@@ -299,19 +299,19 @@
 			>;
 	};
 
-	usb0_pins: pinmux_usb0_pins {
+	usb0_pins: usb0-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1)	/* USB0_DRVVBUS */
 			>;
 	};
 
-	usb1_pins: pinmux_usb1_pins {
+	usb1_pins: usb1-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80)	/* USB1_DRVVBUS */
 			>;
 	};
 
-	gpio1_pins: pinmux_gpio1_pins {
+	gpio1_pins: gpio1-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x081c, PIN_OUTPUT | 0x80)	/* PROGRAM_B */
 			DM814X_IOPAD(0x0820, PIN_INPUT | 0x80)	/* INIT_B */
@@ -336,7 +336,7 @@
 			>;
 	};
 
-	gpio2_pins: pinmux_gpio2_pins {
+	gpio2_pins: gpio2-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x090c, PIN_INPUT_PULLUP | 0x80) /* PHY A IRQ */
 			DM814X_IOPAD(0x0910, PIN_INPUT_PULLUP | 0x80) /* PHY A RESET */
@@ -349,7 +349,7 @@
 		>;
 	};
 
-	gpio4_pins: pinmux_gpio4_pins {
+	gpio4_pins: gpio4-pins {
 		pinctrl-single,pins = <
 			/* The PLL doesn't react well to the SPI controller reset, so
 			 * we force the CS lines to pull up as GPIOs until we're ready.
@@ -364,14 +364,14 @@
 		>;
 	};
 
-	spi2_pins: pinmux_spi2_pins {
+	spi2_pins: spi2-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0950, PIN_INPUT_PULLUP | 0x80) /* PLL SPI CS1 as GPIO */
 			DM814X_IOPAD(0x0818, PIN_INPUT_PULLUP | 0x80) /* PLL SPI CS2 as GPIO */
 		>;
 	};
 
-	spi4_pins: pinmux_spi4_pins {
+	spi4_pins: spi4-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0a7c, 0x20)
 			DM814X_IOPAD(0x0b74, 0x20)
@@ -434,7 +434,7 @@
 };
 
 &mcspi1 {
-	s25fl256@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/ti/omap/am4372.dtsi b/arch/arm/boot/dts/ti/omap/am4372.dtsi
new file mode 100644
index 000000000000..9d2c064534f7
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am4372.dtsi
@@ -0,0 +1,806 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree Source for AM4372 SoC
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/am4.h>
+
+/ {
+	compatible = "ti,am4372", "ti,am43";
+	interrupt-parent = <&wakeupgen>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+		serial5 = &uart5;
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
+		spi0 = &qspi;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu: cpu@0 {
+			compatible = "arm,cortex-a9";
+			enable-method = "ti,am4372";
+			device_type = "cpu";
+			reg = <0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			operating-points-v2 = <&cpu0_opp_table>;
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+			cpu-idle-states = <&mpu_gate>;
+		};
+
+		idle-states {
+			mpu_gate: mpu_gate {
+				compatible = "arm,idle-state";
+				entry-latency-us = <40>;
+				exit-latency-us = <100>;
+				min-residency-us = <300>;
+				local-timer-stop;
+			};
+		};
+	};
+
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		syscon = <&scm_conf>;
+
+		opp-50-300000000 {
+			/* OPP50 */
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <950000 931000 969000>;
+			opp-supported-hw = <0xFF 0x01>;
+			opp-suspend;
+		};
+
+		opp-100-600000000 {
+			/* OPP100 */
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1100000 1078000 1122000>;
+			opp-supported-hw = <0xFF 0x04>;
+		};
+
+		opp-120-720000000 {
+			/* OPP120 */
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1200000 1176000 1224000>;
+			opp-supported-hw = <0xFF 0x08>;
+		};
+
+		opp-800000000{
+			/* OPP Turbo */
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1260000 1234800 1285200>;
+			opp-supported-hw = <0xFF 0x10>;
+		};
+
+		opp-1000000000 {
+			/* OPP Nitro */
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1325000 1298500 1351500>;
+			opp-supported-hw = <0xFF 0x20>;
+		};
+	};
+
+	soc {
+		compatible = "ti,omap-infra";
+	};
+
+	gic: interrupt-controller@48241000 {
+		compatible = "arm,cortex-a9-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48241000 0x1000>,
+		      <0x48240100 0x0100>;
+		interrupt-parent = <&gic>;
+	};
+
+	wakeupgen: interrupt-controller@48281000 {
+		compatible = "ti,omap4-wugen-mpu";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48281000 0x1000>;
+		interrupt-parent = <&gic>;
+	};
+
+	scu: scu@48240000 {
+		compatible = "arm,cortex-a9-scu";
+		reg = <0x48240000 0x100>;
+	};
+
+	global_timer: timer@48240200 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0x48240200 0x100>;
+		interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
+		interrupt-parent = <&gic>;
+		clocks = <&mpu_periphclk>;
+	};
+
+	local_timer: timer@48240600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		reg = <0x48240600 0x100>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>;
+		interrupt-parent = <&gic>;
+		clocks = <&mpu_periphclk>;
+	};
+
+	cache-controller@48242000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x48242000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	ocp@44000000 {
+		compatible = "simple-pm-bus";
+		power-domains = <&prm_per>;
+		clocks = <&l3_clkctrl AM4_L3_L3_MAIN_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		ti,no-idle;
+
+		l3-noc@44000000 {
+			compatible = "ti,am4372-l3-noc";
+			reg = <0x44000000 0x400000>,
+			      <0x44800000 0x400000>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		l4_wkup: interconnect@44c00000 {
+		};
+		l4_per: interconnect@48000000 {
+		};
+		l4_fast: interconnect@4a000000 {
+		};
+
+		target-module@4c000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			reg = <0x4c000000 0x4>;
+			reg-names = "rev";
+			clocks = <&emif_clkctrl AM4_EMIF_EMIF_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4c000000 0x1000000>;
+
+			emif: emif@0 {
+				compatible = "ti,emif-am4372";
+				reg = <0 0x1000000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				sram = <&pm_sram_code
+					&pm_sram_data>;
+			};
+		};
+
+		target-module@49000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49000000 0x4>;
+			reg-names = "rev";
+			clocks = <&l3_clkctrl AM4_L3_TPCC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49000000 0x10000>;
+
+			edma: dma@0 {
+				compatible = "ti,edma3-tpcc";
+				reg = <0 0x10000>;
+				reg-names = "edma3_cc";
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_ccint", "edma3_mperr",
+						  "edma3_ccerrint";
+				dma-requests = <64>;
+				#dma-cells = <2>;
+
+				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
+					   <&edma_tptc2 0>;
+
+				ti,edma-memcpy-channels = <58 59>;
+			};
+		};
+
+		target-module@49800000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49800000 0x4>,
+			      <0x49800010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3_clkctrl AM4_L3_TPTC0_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49800000 0x100000>;
+
+			edma_tptc0: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49900000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49900000 0x4>,
+			      <0x49900010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3_clkctrl AM4_L3_TPTC1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49900000 0x100000>;
+
+			edma_tptc1: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49a00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49a00000 0x4>,
+			      <0x49a00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3_clkctrl AM4_L3_TPTC2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49a00000 0x100000>;
+
+			edma_tptc2: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@47810000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x478102fc 0x4>,
+			      <0x47810110 0x4>,
+			      <0x47810114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&l3s_clkctrl AM4_L3S_MMC3_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x47810000 0x1000>;
+
+			mmc3: mmc@0 {
+				compatible = "ti,am437-sdhci";
+				ti,needs-special-reset;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		sham_target: target-module@53100000 {
+			compatible = "ti,sysc-omap3-sham", "ti,sysc";
+			reg = <0x53100100 0x4>,
+			      <0x53100110 0x4>,
+			      <0x53100114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l3_clkdm */
+			clocks = <&l3_clkctrl AM4_L3_SHAM_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x53100000 0x1000>;
+
+			sham: sham@0 {
+				compatible = "ti,omap5-sham";
+				reg = <0 0x300>;
+				dmas = <&edma 36 0>;
+				dma-names = "rx";
+				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		aes_target: target-module@53501000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x53501080 0x4>,
+			      <0x53501084 0x4>,
+			      <0x53501088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l3_clkdm */
+			clocks = <&l3_clkctrl AM4_L3_AES_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x53501000 0x1000>;
+
+			aes: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma 6 0>,
+				      <&edma 5 0>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		des_target: target-module@53701000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x53701030 0x4>,
+			      <0x53701034 0x4>,
+			      <0x53701038 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l3_clkdm */
+			clocks = <&l3_clkctrl AM4_L3_DES_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x53701000 0x1000>;
+
+			des: des@0 {
+				compatible = "ti,omap4-des";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma 34 0>,
+				       <&edma 33 0>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		pruss_tm: target-module@54400000 {
+			compatible = "ti,sysc-pruss", "ti,sysc";
+			reg = <0x54426000 0x4>,
+			      <0x54426004 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <(SYSC_PRUSS_STANDBY_INIT |
+					 SYSC_PRUSS_SUB_MWAIT)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&pruss_ocp_clkctrl AM4_PRUSS_OCP_PRUSS_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_per 1>;
+			reset-names = "rstctrl";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x54400000 0x80000>;
+
+			pruss1: pruss@0 {
+				compatible = "ti,am4376-pruss1";
+				reg = <0x0 0x40000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				pruss1_mem: memories@0 {
+					reg = <0x0 0x2000>,
+					      <0x2000 0x2000>,
+					      <0x10000 0x8000>;
+					reg-names = "dram0", "dram1",
+						    "shrdram2";
+				};
+
+				pruss1_cfg: cfg@26000 {
+					compatible = "ti,pruss-cfg", "syscon";
+					reg = <0x26000 0x2000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x26000 0x2000>;
+
+					clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						pruss1_iepclk_mux: iepclk-mux@30 {
+							reg = <0x30>;
+							#clock-cells = <0>;
+							clocks = <&sysclk_div>,     /* icss_iep_gclk */
+								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+						};
+					};
+				};
+
+				pruss1_mii_rt: mii-rt@32000 {
+					compatible = "ti,pruss-mii", "syscon";
+					reg = <0x32000 0x58>;
+				};
+
+				pruss1_intc: interrupt-controller@20000 {
+					compatible = "ti,pruss-intc";
+					reg = <0x20000 0x2000>;
+					interrupt-controller;
+					#interrupt-cells = <3>;
+					interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "host_intr0", "host_intr1",
+							  "host_intr2", "host_intr3",
+							  "host_intr4",
+							  "host_intr6", "host_intr7";
+					ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
+				};
+
+				pru1_0: pru@34000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x34000 0x3000>,
+					      <0x22000 0x400>,
+					      <0x22400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru1_0-fw";
+				};
+
+				pru1_1: pru@38000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x38000 0x3000>,
+					      <0x24000 0x400>,
+					      <0x24400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru1_1-fw";
+				};
+
+				pruss1_mdio: mdio@32400 {
+					compatible = "ti,davinci_mdio";
+					reg = <0x32400 0x90>;
+					clocks = <&dpll_core_m4_ck>;
+					clock-names = "fck";
+					bus_freq = <1000000>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+
+			pruss0: pruss@40000 {
+				compatible = "ti,am4376-pruss0";
+				reg = <0x40000 0x40000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				pruss0_mem: memories@40000 {
+					reg = <0x40000 0x1000>,
+					      <0x42000 0x1000>;
+					reg-names = "dram0", "dram1";
+				};
+
+				pruss0_cfg: cfg@66000 {
+					compatible = "ti,pruss-cfg", "syscon";
+					reg = <0x66000 0x2000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x66000 0x2000>;
+
+					clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						pruss0_iepclk_mux: iepclk-mux@30 {
+							reg = <0x30>;
+							#clock-cells = <0>;
+							clocks = <&sysclk_div>,     /* icss_iep_gclk */
+								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+						};
+					};
+				};
+
+				pruss0_mii_rt: mii-rt@72000 {
+					compatible = "ti,pruss-mii", "syscon";
+					reg = <0x72000 0x58>;
+					status = "disabled";
+				};
+
+				pruss0_intc: interrupt-controller@60000 {
+					compatible = "ti,pruss-intc";
+					reg = <0x60000 0x2000>;
+					interrupt-controller;
+					#interrupt-cells = <3>;
+					interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "host_intr0", "host_intr1",
+							  "host_intr2", "host_intr3",
+							  "host_intr4",
+							  "host_intr6", "host_intr7";
+					ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
+				};
+
+				pru0_0: pru@74000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x74000 0x1000>,
+					      <0x62000 0x400>,
+					      <0x62400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru0_0-fw";
+				};
+
+				pru0_1: pru@78000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x78000 0x1000>,
+					      <0x64000 0x400>,
+					      <0x64400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru0_1-fw";
+				};
+			};
+		};
+
+		target-module@50000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x50000000 4>,
+			      <0x50000010 4>,
+			      <0x50000014 4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&l3s_clkctrl AM4_L3S_GPMC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
+				 <0x00000000 0x00000000 0x40000000>; /* data */
+
+			gpmc: gpmc@50000000 {
+				compatible = "ti,am3352-gpmc";
+				dmas = <&edma 52 0>;
+				dma-names = "rxtx";
+				clocks = <&l3s_gclk>;
+				clock-names = "fck";
+				reg = <0x50000000 0x2000>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+				gpmc,num-cs = <7>;
+				gpmc,num-waitpins = <2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		target-module@47900000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x47900000 0x4>,
+			      <0x47900010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&l3s_clkctrl AM4_L3S_QSPI_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x47900000 0x1000>,
+				 <0x30000000 0x30000000 0x4000000>;
+
+			qspi: spi@0 {
+				compatible = "ti,am4372-qspi";
+				reg = <0 0x100>,
+				      <0x30000000 0x4000000>;
+				reg-names = "qspi_base", "qspi_mmap";
+				clocks = <&dpll_per_m2_div4_ck>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <0 138 0x4>;
+				num-cs = <4>;
+			};
+		};
+
+		target-module@40300000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			clocks = <&l3_clkctrl AM4_L3_OCMCRAM_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40300000 0x40000>;
+
+			ocmcram: sram@0 {
+				compatible = "mmio-sram";
+				reg = <0 0x40000>; /* 256k */
+				ranges = <0 0 0x40000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				pm_sram_code: pm-code-sram@0 {
+					compatible = "ti,sram";
+					reg = <0x0 0x1000>;
+					protect-exec;
+				};
+
+				pm_sram_data: pm-data-sram@1000 {
+					compatible = "ti,sram";
+					reg = <0x1000 0x1000>;
+					pool;
+				};
+			};
+		};
+
+		target-module@56000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5600fe00 0x4>,
+			      <0x5600fe10 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&gfx_l3_clkctrl AM4_GFX_L3_GFX_CLKCTRL 0>;
+			clock-names = "fck";
+			power-domains = <&prm_gfx>;
+			resets = <&prm_gfx 0>;
+			reset-names = "rstctrl";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x56000000 0x1000000>;
+		};
+	};
+};
+
+#include "am437x-l4.dtsi"
+#include "am43xx-clocks.dtsi"
+
+&prcm {
+	prm_mpu: prm@300 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x300 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_gfx: prm@400 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x400 0x100>;
+		#power-domain-cells = <0>;
+		#reset-cells = <1>;
+	};
+
+	prm_rtc: prm@500 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x500 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_tamper: prm@600 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x600 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_cefuse: prm@700 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x700 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_per: prm@800 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x800 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_wkup: prm@2000 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x2000 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_device: prm@4000 {
+		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x4000 0x100>;
+		#reset-cells = <1>;
+	};
+};
+
+/* Preferred always-on timer for clocksource */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	clocks = <&l4_wkup_clkctrl AM4_L4_WKUP_TIMER1_CLKCTRL 0>,
+		 <&l4_wkup_clkctrl AM4_L4_WKUP_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck", "ick";
+	timer@0 {
+		assigned-clocks = <&timer1_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	clocks = <&l4ls_clkctrl AM4_L4LS_TIMER2_CLKCTRL 0>,
+		 <&l4ls_clkctrl AM4_L4LS_L4_LS_CLKCTRL 0>;
+	clock-names = "fck", "ick";
+	timer@0 {
+		assigned-clocks = <&timer2_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/ti/omap/am437x-cm-t43.dts
index 063113a5da2d..9ec75d03eaff 100644
--- a/arch/arm/boot/dts/am437x-cm-t43.dts
+++ b/arch/arm/boot/dts/ti/omap/am437x-cm-t43.dts
@@ -38,20 +38,20 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&cm_t43_led_pins>;
 
-	cm_t43_led_pins: cm_t43_led_pins {
+	cm_t43_led_pins: cm-t43-led-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa78, MUX_MODE7)
 		>;
 	};
 
-	i2c0_pins: i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
 			AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	emmc_pins: emmc_pins {
+	emmc_pins: emmc-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x820, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad8.mmc1_dat0 */
 			AM4372_IOPAD(0x824, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad9.mmc1_dat1 */
@@ -66,7 +66,7 @@
 		>;
 	};
 
-	spi0_pins: pinmux_spi0_pins {
+	spi0_pins: spi0-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0) /* spi0_sclk.spi0_sclk */
 			AM4372_IOPAD(0x954, PIN_INPUT | MUX_MODE0) /* spi0_d0.spi0_d0 */
@@ -75,7 +75,7 @@
 		>;
 	};
 
-	nand_flash_x8: nand_flash_x8 {
+	nand_flash_x8: nand-flash-x8-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x800, PIN_INPUT | PULL_DISABLE | MUX_MODE0)
 			AM4372_IOPAD(0x804, PIN_INPUT | PULL_DISABLE | MUX_MODE0)
@@ -95,7 +95,7 @@
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_txen */
@@ -128,7 +128,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
@@ -291,7 +291,7 @@
 	pinctrl-0 = <&emmc_pins>;
 	vmmc-supply = <&vmmc_3v3>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 };
 
 &spi0 {
@@ -302,7 +302,7 @@
 		&edma 17 0>;
 	dma-names = "tx0", "rx0";
 
-	flash: w25q64cvzpig@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -325,17 +325,15 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -346,16 +344,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii-txid";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &dwc3_1 {
@@ -401,7 +399,7 @@
 	tsc {
 		ti,wires = <4>;
 		ti,x-plate-resistance = <200>;
-		ti,coordiante-readouts = <5>;
+		ti,coordinate-readouts = <5>;
 		ti,wire-config = <0x00 0x11 0x22 0x33>;
 	};
 
@@ -418,3 +416,7 @@
 			   <600000 1100000>,
 			   <300000 950000>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/ti/omap/am437x-gp-evm.dts
index cae4500194fe..f7aad0323d19 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am437x-gp-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /* AM437x GP EVM */
@@ -86,27 +86,11 @@
 		};
 
 	lcd0: display {
-		compatible = "osddisplays,osd057T0559-34ts", "panel-dpi";
+		compatible = "osddisplays,osd070t1718-19ts", "panel-dpi";
 		label = "lcd";
 
 		backlight = <&lcd_bl>;
 
-		panel-timing {
-			clock-frequency = <33000000>;
-			hactive = <800>;
-			vactive = <480>;
-			hfront-porch = <210>;
-			hback-porch = <16>;
-			hsync-len = <30>;
-			vback-porch = <10>;
-			vfront-porch = <22>;
-			vsync-len = <13>;
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-
 		port {
 			lcd_in: endpoint {
 				remote-endpoint = <&dpi_out>;
@@ -169,45 +153,45 @@
 	pinctrl-0 = <&wlan_pins_default &ddr3_vtt_toggle_default &unused_pins &debugss_pins>;
 	pinctrl-1 = <&wlan_pins_sleep>;
 
-	ddr3_vtt_toggle_default: ddr_vtt_toggle_default {
+	ddr3_vtt_toggle_default: ddr-vtt-toggle-default-pins {
 		pinctrl-single,pins = <
 			0x25C (DS0_PULL_UP_DOWN_EN | PIN_OUTPUT_PULLUP | DS0_FORCE_OFF_MODE | MUX_MODE7) /* spi0_cs0.gpio5_7 */
 		>;
 	};
 
-	i2c0_pins: i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
 			AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	i2c1_pins: i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x95c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
 			AM4372_IOPAD(0x958, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
 		>;
 	};
 
-	ecap0_pins: backlight_pins {
+	ecap0_pins: backlight-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x964, MUX_MODE0)       /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
 		>;
 	};
 
-	pixcir_ts_pins: pixcir_ts_pins {
+	pixcir_ts_pins: pixcir-ts-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa64, PIN_INPUT_PULLUP | MUX_MODE7)  /* spi2_d0.gpio3_22 */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_txen */
@@ -225,7 +209,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM4372_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -243,7 +227,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
@@ -251,7 +235,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -259,7 +243,7 @@
 		>;
 	};
 
-	nand_flash_x8: nand_flash_x8 {
+	nand_flash_x8: nand-flash-x8-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x800, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
 			AM4372_IOPAD(0x804, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
@@ -279,7 +263,7 @@
 		>;
 	};
 
-	dss_pins: dss_pins {
+	dss_pins: dss-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x820, PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */
 			AM4372_IOPAD(0x824, PIN_OUTPUT_PULLUP | MUX_MODE1)
@@ -313,42 +297,42 @@
 		>;
 	};
 
-	display_mux_pins: display_mux_pins {
+	display_mux_pins: display-mux-pins {
 		pinctrl-single,pins = <
 			/* GPIO 5_8 to select LCD / HDMI */
 			AM4372_IOPAD(0xa38, PIN_OUTPUT_PULLUP | MUX_MODE7)
 		>;
 	};
 
-	dcan0_default: dcan0_default_pins {
+	dcan0_default: dcan0-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x978, PIN_OUTPUT | MUX_MODE2)		/* uart1_ctsn.d_can0_tx */
 			AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_rtsn.d_can0_rx */
 		>;
 	};
 
-	dcan0_sleep: dcan0_sleep_pins {
+	dcan0_sleep: dcan0-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE7)	/* uart1_ctsn.gpio0_12 */
 			AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE7)	/* uart1_rtsn.gpio0_13 */
 		>;
 	};
 
-	dcan1_default: dcan1_default_pins {
+	dcan1_default: dcan1-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x980, PIN_OUTPUT | MUX_MODE2)		/* uart1_rxd.d_can1_tx */
 			AM4372_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_txd.d_can1_rx */
 		>;
 	};
 
-	dcan1_sleep: dcan1_sleep_pins {
+	dcan1_sleep: dcan1-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE7)	/* uart1_rxd.gpio0_14 */
 			AM4372_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE7)	/* uart1_txd.gpio0_15 */
 		>;
 	};
 
-	vpfe0_pins_default: vpfe0_pins_default {
+	vpfe0_pins_default: vpfe0-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_hd mode 0*/
 			AM4372_IOPAD(0x9b4, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_vd mode 0*/
@@ -366,7 +350,7 @@
 		>;
 	};
 
-	vpfe0_pins_sleep: vpfe0_pins_sleep {
+	vpfe0_pins_sleep: vpfe0-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9b0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_hd mode 0*/
 			AM4372_IOPAD(0x9b4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_vd mode 0*/
@@ -384,7 +368,7 @@
 		>;
 	};
 
-	vpfe1_pins_default: vpfe1_pins_default {
+	vpfe1_pins_default: vpfe1-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9cc, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data9 mode 0*/
 			AM4372_IOPAD(0x9d0, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data8 mode 0*/
@@ -402,7 +386,7 @@
 		>;
 	};
 
-	vpfe1_pins_sleep: vpfe1_pins_sleep {
+	vpfe1_pins_sleep: vpfe1-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9cc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data9 mode 0*/
 			AM4372_IOPAD(0x9d0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data8 mode 0*/
@@ -420,7 +404,7 @@
 		>;
 	};
 
-	mmc3_pins_default: pinmux_mmc3_pins_default {
+	mmc3_pins_default: mmc3-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_clk.mmc2_clk */
 			AM4372_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_csn3.mmc2_cmd */
@@ -431,7 +415,7 @@
 		>;
 	};
 
-	mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+	mmc3_pins_sleep: mmc3-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x88c, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_clk.mmc2_clk */
 			AM4372_IOPAD(0x888, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.mmc2_cmd */
@@ -442,7 +426,7 @@
 		>;
 	};
 
-	wlan_pins_default: pinmux_wlan_pins_default {
+	wlan_pins_default: wlan-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a4.gpio1_20 WL_EN */
 			AM4372_IOPAD(0x85c, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* gpmc_a7.gpio1_23 WL_IRQ*/
@@ -450,7 +434,7 @@
 		>;
 	};
 
-	wlan_pins_sleep: pinmux_wlan_pins_sleep {
+	wlan_pins_sleep: wlan-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a4.gpio1_20 WL_EN */
 			AM4372_IOPAD(0x85c, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* gpmc_a7.gpio1_23 WL_IRQ*/
@@ -458,7 +442,7 @@
 		>;
 	};
 
-	uart3_pins: uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa28, PIN_INPUT | MUX_MODE0)		/* uart3_rxd.uart3_rxd */
 			AM4372_IOPAD(0xa2c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_txd.uart3_txd */
@@ -467,7 +451,7 @@
 		>;
 	};
 
-	mcasp1_pins: mcasp1_pins {
+	mcasp1_pins: mcasp1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x908, PIN_OUTPUT_PULLDOWN | MUX_MODE4)	/* mii1_col.mcasp1_axr2 */
 			AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* mii1_crs.mcasp1_aclkx */
@@ -476,7 +460,7 @@
 		>;
 	};
 
-	mcasp1_sleep_pins: mcasp1_sleep_pins {
+	mcasp1_sleep_pins: mcasp1-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -485,13 +469,13 @@
 		>;
 	};
 
-	gpio0_pins: gpio0_pins {
+	gpio0_pins: gpio0-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa6c, PIN_OUTPUT | MUX_MODE9) /* spi2_cs0.gpio0_23 SEL_eMMCorNANDn */
 		>;
 	};
 
-	emmc_pins_default: emmc_pins_default {
+	emmc_pins_default: emmc-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
 			AM4372_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
@@ -506,7 +490,7 @@
 		>;
 	};
 
-	emmc_pins_sleep: emmc_pins_sleep {
+	emmc_pins_sleep: emmc-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x800, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad0.gpio1_0 */
 			AM4372_IOPAD(0x804, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad1.gpio1_1 */
@@ -521,19 +505,19 @@
 		>;
 	};
 
-	beeper_pins_default: beeper_pins_default {
+	beeper_pins_default: beeper-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9e0, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* cam1_field.gpio4_12 */
 		>;
 	};
 
-	beeper_pins_sleep: beeper_pins_sleep {
+	beeper_pins_sleep: beeper-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9e0, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* cam1_field.gpio4_12 */
 		>;
 	};
 
-	unused_pins: unused_pins {
+	unused_pins: unused-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x854, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -582,7 +566,7 @@
 		>;
 	};
 
-	debugss_pins: pinmux_debugss_pins {
+	debugss_pins: debugss-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa90, PIN_INPUT_PULLDOWN)
 			AM4372_IOPAD(0xa94, PIN_INPUT_PULLDOWN)
@@ -594,7 +578,7 @@
 		>;
 	};
 
-	uart0_pins_default: uart0_pins_default {
+	uart0_pins_default: uart0-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) /* uart0_ctsn.uart0_ctsn */
 			AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) /* uart0_rtsn.uart0_rtsn */
@@ -603,7 +587,7 @@
 		>;
 	};
 
-	uart0_pins_sleep: uart0_pins_sleep {
+	uart0_pins_sleep: uart0-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* uart0_ctsn.uart0_ctsn */
 			AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) /* uart0_rtsn.uart0_rtsn */
@@ -612,7 +596,7 @@
 		>;
 	};
 
-	matrix_keypad_default: matrix_keypad_default {
+	matrix_keypad_default: matrix-keypad-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7)
 			AM4372_IOPAD(0x9a8, PIN_OUTPUT | MUX_MODE7)
@@ -621,7 +605,7 @@
 		>;
 	};
 
-	matrix_keypad_sleep: matrix_keypad_sleep {
+	matrix_keypad_sleep: matrix-keypad-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9a4, PULL_UP | MUX_MODE7)
 			AM4372_IOPAD(0x9a8, PULL_UP | MUX_MODE7)
@@ -791,6 +775,14 @@
 	};
 };
 
+&magadc {
+	status = "okay";
+
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
 &ecap0 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -802,7 +794,7 @@
 	pinctrl-0 = <&gpio0_pins>;
 	status = "okay";
 
-	p23 {
+	sel-emmc-nand-hog {
 		gpio-hog;
 		gpios = <23 GPIO_ACTIVE_HIGH>;
 		/* SelEMMCorNAND selects between eMMC and NAND:
@@ -829,13 +821,16 @@
 	status = "okay";
 };
 
+&gpio5_target {
+	ti,no-reset-on-init;
+};
+
 &gpio5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&display_mux_pins>;
 	status = "okay";
-	ti,no-reset-on-init;
 
-	p8 {
+	sel-lcd-hdmi-hog {
 		/*
 		 * SelLCDorHDMI selects between display and audio paths:
 		 * Low: HDMI display with audio via HDMI
@@ -869,7 +864,7 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&emmc_pins_default>;
 	pinctrl-1 = <&emmc_pins_sleep>;
-	ti,non-removable;
+	non-removable;
 };
 
 &mmc3 {
@@ -886,7 +881,7 @@
 	pinctrl-1 = <&mmc3_pins_sleep>;
 	cap-power-off-card;
 	keep-power-in-suspend;
-	ti,non-removable;
+	non-removable;
 
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -922,28 +917,31 @@
 	status = "okay";
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 &elm {
@@ -1040,7 +1038,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_pins>;
@@ -1128,3 +1126,12 @@
 &cpu {
 	cpu0-supply = <&dcdc2>;
 };
+
+&wkup_m3_ipc {
+	ti,set-io-isolation;
+	firmware-name = "am43x-evm-scale-data.bin";
+};
+
+&pruss1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/ti/omap/am437x-idk-evm.dts
index f3ced6df0c9b..00682ce7e14c 100644
--- a/arch/arm/boot/dts/am437x-idk-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am437x-idk-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /dts-v1/;
@@ -58,7 +58,7 @@
 		vin-supply = <&vdd_corereg>;
 	};
 
-	v1_8dreg: fixed-regulator-v1_8dreg{
+	v1_8dreg: fixed-regulator-v1_8dreg {
 		compatible = "regulator-fixed";
 		regulator-name = "V1_8DREG";
 		regulator-min-microvolt = <1800000>;
@@ -68,7 +68,7 @@
 		vin-supply = <&v24_0d>;
 	};
 
-	v1_8d: fixed-regulator-v1_8d{
+	v1_8d: fixed-regulator-v1_8d {
 		compatible = "regulator-fixed";
 		regulator-name = "V1_8D";
 		regulator-min-microvolt = <1800000>;
@@ -78,7 +78,7 @@
 		vin-supply = <&v1_8dreg>;
 	};
 
-	v1_5dreg: fixed-regulator-v1_5dreg{
+	v1_5dreg: fixed-regulator-v1_5dreg {
 		compatible = "regulator-fixed";
 		regulator-name = "V1_5DREG";
 		regulator-min-microvolt = <1500000>;
@@ -88,7 +88,7 @@
 		vin-supply = <&v24_0d>;
 	};
 
-	v1_5d: fixed-regulator-v1_5d{
+	v1_5d: fixed-regulator-v1_5d {
 		compatible = "regulator-fixed";
 		regulator-name = "V1_5D";
 		regulator-min-microvolt = <1500000>;
@@ -98,14 +98,12 @@
 		vin-supply = <&v1_5dreg>;
 	};
 
-	gpio_keys: gpio_keys {
+	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_pins_default>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		switch0 {
+		switch-0 {
 			label = "power-button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
@@ -173,41 +171,41 @@
 };
 
 &am43xx_pinmux {
-	gpio_keys_pins_default: gpio_keys_pins_default {
+	gpio_keys_pins_default: gpio-keys-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9b8, PIN_INPUT | MUX_MODE7)	/* cam0_field.gpio4_2 */
 		>;
 	};
 
-	i2c0_pins_default: i2c0_pins_default {
+	i2c0_pins_default: i2c0-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x988, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */
 			AM4372_IOPAD(0x98c, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	i2c0_pins_sleep: i2c0_pins_sleep {
+	i2c0_pins_sleep: i2c0-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x988, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x98c, PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
 
-	i2c2_pins_default: i2c2_pins_default {
+	i2c2_pins_default: i2c2-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9e8, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data1.i2c2_scl */
 			AM4372_IOPAD(0x9ec, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data0.i2c2_sda */
 		>;
 	};
 
-	i2c2_pins_sleep: i2c2_pins_sleep {
+	i2c2_pins_sleep: i2c2-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9e8, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x9ec, PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
 
-	mmc1_pins_default: pinmux_mmc1_pins_default {
+	mmc1_pins_default: mmc1-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x900, PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */
 			AM4372_IOPAD(0x904, PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
@@ -219,7 +217,7 @@
 		>;
 	};
 
-	mmc1_pins_sleep: pinmux_mmc1_pins_sleep {
+	mmc1_pins_sleep: mmc1-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x900, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x904, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -231,7 +229,7 @@
 		>;
 	};
 
-	spi1_pins_default: spi1_pins_default {
+	spi1_pins_default: spi1-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x908, PIN_INPUT | MUX_MODE2)	/* mii1_col.spi1_sclk */
 			AM4372_IOPAD(0x910, PIN_INPUT | MUX_MODE2)	/* mii1_rx_er.spi1_d1 */
@@ -240,7 +238,7 @@
 		>;
 	};
 
-	spi1_pins_sleep: spi1_pins_sleep {
+	spi1_pins_sleep: spi1-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -249,13 +247,13 @@
 		>;
 	};
 
-	ecap0_pins_default: backlight_pins_default {
+	ecap0_pins_default: backlight-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x964, PIN_OUTPUT | MUX_MODE0) /* ecap0_in_pwm0_out.ecap0_in_pwm0_out */
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txclk.rgmii1_tclk */
 			AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
@@ -272,7 +270,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -289,7 +287,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
@@ -297,7 +295,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -305,7 +303,7 @@
 		>;
 	};
 
-	qspi_pins_default: qspi_pins_default {
+	qspi_pins_default: qspi-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x87c, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_csn0.qspi_csn */
 			AM4372_IOPAD(0x888, PIN_OUTPUT | MUX_MODE2)		/* gpmc_csn3.qspi_clk */
@@ -316,7 +314,7 @@
 		>;
 	};
 
-	qspi_pins_sleep: qspi_pins_sleep{
+	qspi_pins_sleep: qspi-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x87c, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x888, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -437,7 +435,7 @@
 	pinctrl-1 = <&qspi_pins_sleep>;
 
 	spi-max-frequency = <48000000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx66l51235l";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
@@ -454,7 +452,7 @@
 		 */
 		partition@0 {
 			label = "QSPI.U_BOOT";
-			reg = <0x00000000 0x000080000>;
+			reg = <0x00000000 0x00080000>;
 		};
 		partition@1 {
 			label = "QSPI.U_BOOT.backup";
@@ -483,28 +481,31 @@
 	};
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 &rtc {
@@ -526,11 +527,17 @@
 	 * Supply voltage supervisor on board will not allow opp50 so
 	 * disable it and set opp100 as suspend OPP.
 	 */
-	opp50@300000000 {
+	opp-50-300000000 {
+		/* opp50-300000000 */
 		status = "disabled";
 	};
 
-	opp100@600000000 {
+	opp-100-600000000 {
+		/* opp100-600000000 */
 		opp-suspend;
 	};
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am437x-l4.dtsi b/arch/arm/boot/dts/ti/omap/am437x-l4.dtsi
index 0dd59ee14585..824b9415ebbe 100644
--- a/arch/arm/boot/dts/am437x-l4.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am437x-l4.dtsi
@@ -1,5 +1,8 @@
 &l4_wkup {						/* 0x44c00000 */
-	compatible = "ti,am4-l4-wkup", "simple-bus";
+	compatible = "ti,am4-l4-wkup", "simple-pm-bus";
+	power-domains = <&prm_wkup>;
+	clocks = <&l4_wkup_clkctrl AM4_L4_WKUP_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x44c00000 0x800>,
 	      <0x44c00800 0x800>,
 	      <0x44c01000 0x400>,
@@ -12,7 +15,7 @@
 		 <0x00200000 0x44e00000 0x100000>;	/* segment 2 */
 
 	segment@0 {					/* 0x44c00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -22,7 +25,7 @@
 	};
 
 	segment@100000 {					/* 0x44d00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00100000 0x004000>,	/* ap 4 */
@@ -32,19 +35,25 @@
 			 <0x000f0000 0x001f0000 0x010000>;	/* ap 8 */
 
 		target-module@0 {			/* 0x44d00000, ap 4 28.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x0 0x4>;
+			reg-names = "rev";
+			clocks = <&l4_wkup_aon_clkctrl AM4_L4_WKUP_AON_WKUP_M3_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <0x0 0x0 0x4000>;
-		};
+			ranges = <0x00000000 0x00000000 0x4000>,
+				 <0x00080000 0x00080000 0x2000>;
 
-		target-module@80000 {			/* 0x44d80000, ap 6 10.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0x80000 0x2000>;
+			wkup_m3: cpu@0 {
+				compatible = "ti,am4372-wkup-m3";
+				reg = <0x00000000 0x4000>,
+				      <0x00080000 0x2000>;
+				reg-names = "umem", "dmem";
+				resets = <&prm_wkup 3>;
+				reset-names = "rstctrl";
+				ti,pm-firmware = "am335x-pm-firmware.elf";
+			};
 		};
 
 		target-module@f0000 {			/* 0x44df0000, ap 8 58.0 */
@@ -75,7 +84,7 @@
 	};
 
 	segment@200000 {					/* 0x44e00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00200000 0x001000>,	/* ap 9 */
@@ -185,7 +194,7 @@
 			ranges = <0x0 0x9000 0x1000>;
 
 			uart0: serial@0 {
-				compatible = "ti,am4372-uart","ti,omap2-uart";
+				compatible = "ti,am4372-uart";
 				reg = <0x0 0x2000>;
 				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			};
@@ -225,7 +234,6 @@
 
 		target-module@d000 {			/* 0x44e0d000, ap 20 38.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "adc_tsc";
 			reg = <0xd000 0x4>,
 			      <0xd010 0x4>;
 			reg-names = "rev", "sysc";
@@ -266,6 +274,9 @@
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0x10000 0x4>;
 			reg-names = "rev";
+			clocks = <&l4_wkup_clkctrl AM4_L4_WKUP_CONTROL_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x10000 0x10000>;
@@ -329,9 +340,8 @@
 			};
 		};
 
-		target-module@31000 {			/* 0x44e31000, ap 24 40.0 */
+		timer1_target: target-module@31000 {	/* 0x44e31000, ap 24 40.0 */
 			compatible = "ti,sysc-omap2-timer", "ti,sysc";
-			ti,hwmods = "timer1";
 			reg = <0x31000 0x4>,
 			      <0x31010 0x4>,
 			      <0x31014 0x4>;
@@ -411,9 +421,8 @@
 			ranges = <0x0 0x39000 0x1000>;
 		};
 
-		target-module@3e000 {			/* 0x44e3e000, ap 34 60.0 */
+		rtc_target: target-module@3e000 {	/* 0x44e3e000, ap 34 60.0 */
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
-			ti,hwmods = "rtc";
 			reg = <0x3e074 0x4>,
 			      <0x3e078 0x4>;
 			reg-names = "rev", "sysc";
@@ -422,6 +431,7 @@
 					<SYSC_IDLE_SMART>,
 					<SYSC_IDLE_SMART_WKUP>;
 			/* Domains (P, C): rtc_pwrdm, l4_rtc_clkdm */
+			power-domains = <&prm_rtc>;
 			clocks = <&l4_rtc_clkctrl AM4_L4_RTC_RTC_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
@@ -432,8 +442,8 @@
 				compatible = "ti,am4372-rtc", "ti,am3352-rtc",
 					     "ti,da830-rtc";
 				reg = <0x0 0x1000>;
-				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH
-					      GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk_32768_ck>;
 				clock-names = "int-clk";
 				system-power-controller;
@@ -451,7 +461,6 @@
 
 		target-module@86000 {			/* 0x44e86000, ap 40 70.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "counter_32k";
 			reg = <0x86000 0x4>,
 			      <0x86004 0x4>;
 			reg-names = "rev", "sysc";
@@ -483,7 +492,10 @@
 };
 
 &l4_fast {					/* 0x4a000000 */
-	compatible = "ti,am4-l4-fast", "simple-bus";
+	compatible = "ti,am4-l4-fast", "simple-pm-bus";
+	power-domains = <&prm_per>;
+	clocks = <&l3_clkctrl AM4_L3_L4_HS_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4a000000 0x800>,
 	      <0x4a000800 0x800>,
 	      <0x4a001000 0x400>;
@@ -493,7 +505,7 @@
 	ranges = <0x00000000 0x4a000000 0x1000000>;	/* segment 0 */
 
 	segment@0 {					/* 0x4a000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -524,54 +536,57 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x100000 0x8000>;
 
-			mac: ethernet@0 {
-				compatible = "ti,am4372-cpsw","ti,cpsw";
-				reg = <0x0 0x800
-				       0x1200 0x100>;
-				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH
-					      GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
-					      GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
-					      GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>,
-					 <&dpll_clksel_mac_clk>;
-				clock-names = "fck", "cpts", "50mclk";
+			mac_sw: switch@0 {
+				compatible = "ti,am4372-cpsw-switch", "ti,cpsw-switch";
+				reg = <0x0 0x4000>;
+				ranges = <0 0 0x4000>;
+				clocks = <&cpsw_125mhz_gclk>, <&dpll_clksel_mac_clk>;
+				clock-names = "fck", "50mclk";
 				assigned-clocks = <&dpll_clksel_mac_clk>;
 				assigned-clock-rates = <50000000>;
-				status = "disabled";
-				cpdma_channels = <8>;
-				ale_entries = <1024>;
-				bd_ram_size = <0x2000>;
-				mac_control = <0x20>;
-				slaves = <2>;
-				active_slave = <0>;
-				cpts_clock_mult = <0x80000000>;
-				cpts_clock_shift = <29>;
-				ranges = <0 0 0x8000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
 				syscon = <&scm_conf>;
+				status = "disabled";
 
-				davinci_mdio: mdio@1000 {
-					compatible = "ti,am4372-mdio","ti,cpsw-mdio","ti,davinci_mdio";
-					reg = <0x1000 0x100>;
-					clocks = <&cpsw_125mhz_clkctrl AM4_CPSW_125MHZ_CPGMAC0_CLKCTRL 0>;
-					clock-names = "fck";
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "rx_thresh", "rx", "tx", "misc";
+
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
-					bus_freq = <1000000>;
-					status = "disabled";
+
+					cpsw_port1: port@1 {
+						reg = <1>;
+						label = "port1";
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 1 0>;
+					};
+
+					cpsw_port2: port@2 {
+						reg = <2>;
+						label = "port2";
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 2 0>;
+					};
 				};
 
-				cpsw_emac0: slave@200 {
-					/* Filled in by U-Boot */
-					mac-address = [ 00 00 00 00 00 00 ];
-					phys = <&phy_gmii_sel 1 0>;
+				davinci_mdio_sw: mdio@1000 {
+					compatible = "ti,am4372-mdio", "ti,cpsw-mdio","ti,davinci_mdio";
+					clocks = <&cpsw_125mhz_gclk>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					bus_freq = <1000000>;
+					reg = <0x1000 0x100>;
 				};
 
-				cpsw_emac1: slave@300 {
-					/* Filled in by U-Boot */
-					mac-address = [ 00 00 00 00 00 00 ];
-					phys = <&phy_gmii_sel 2 0>;
+				cpts {
+					clocks = <&cpsw_cpts_rft_clk>;
+					clock-names = "cpts";
 				};
 			};
 		};
@@ -595,7 +610,10 @@
 };
 
 &l4_per {					/* 0x48000000 */
-	compatible = "ti,am4-l4-per", "simple-bus";
+	compatible = "ti,am4-l4-per", "simple-pm-bus";
+	power-domains = <&prm_per>;
+	clocks = <&l4ls_clkctrl AM4_L4LS_L4_LS_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48000000 0x800>,
 	      <0x48000800 0x800>,
 	      <0x48001000 0x400>,
@@ -613,7 +631,7 @@
 		 <0x46400000 0x46400000 0x400000>;	/* l3 data port */
 
 	segment@0 {					/* 0x48000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -694,7 +712,7 @@
 			ranges = <0x0 0x22000 0x1000>;
 
 			uart1: serial@0 {
-				compatible = "ti,am4372-uart","ti,omap2-uart";
+				compatible = "ti,am4372-uart";
 				reg = <0x0 0x2000>;
 				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -722,7 +740,7 @@
 			ranges = <0x0 0x24000 0x1000>;
 
 			uart2: serial@0 {
-				compatible = "ti,am4372-uart","ti,omap2-uart";
+				compatible = "ti,am4372-uart";
 				reg = <0x0 0x2000>;
 				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -763,7 +781,6 @@
 
 		target-module@30000 {			/* 0x48030000, ap 65 08.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi0";
 			reg = <0x30000 0x4>,
 			      <0x30110 0x4>,
 			      <0x30114 0x4>;
@@ -870,9 +887,8 @@
 			};
 		};
 
-		target-module@40000 {			/* 0x48040000, ap 18 1e.0 */
+		timer2_target: target-module@40000 {	/* 0x48040000, ap 18 1e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer2";
 			reg = <0x40000 0x4>,
 			      <0x40010 0x4>,
 			      <0x40014 0x4>;
@@ -900,7 +916,6 @@
 
 		target-module@42000 {			/* 0x48042000, ap 20 24.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer3";
 			reg = <0x42000 0x4>,
 			      <0x42010 0x4>,
 			      <0x42014 0x4>;
@@ -927,7 +942,6 @@
 
 		target-module@44000 {			/* 0x48044000, ap 22 26.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer4";
 			reg = <0x44000 0x4>,
 			      <0x44010 0x4>,
 			      <0x44014 0x4>;
@@ -955,7 +969,6 @@
 
 		target-module@46000 {			/* 0x48046000, ap 24 28.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer5";
 			reg = <0x46000 0x4>,
 			      <0x46010 0x4>,
 			      <0x46014 0x4>;
@@ -983,7 +996,6 @@
 
 		target-module@48000 {			/* 0x48048000, ap 26 1a.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer6";
 			reg = <0x48000 0x4>,
 			      <0x48010 0x4>,
 			      <0x48014 0x4>;
@@ -1011,7 +1023,6 @@
 
 		target-module@4a000 {			/* 0x4804a000, ap 71 48.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer7";
 			reg = <0x4a000 0x4>,
 			      <0x4a010 0x4>,
 			      <0x4a014 0x4>;
@@ -1093,9 +1104,8 @@
 			ranges = <0x0 0x60000 0x1000>;
 
 			mmc1: mmc@0 {
-				compatible = "ti,omap4-hsmmc";
+				compatible = "ti,am437-sdhci";
 				reg = <0x0 0x1000>;
-				ti,dual-volt;
 				ti,needs-special-reset;
 				dmas = <&edma 24 0>,
 					<&edma 25 0>;
@@ -1107,7 +1117,6 @@
 
 		target-module@80000 {			/* 0x48080000, ap 32 18.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "elm";
 			reg = <0x80000 0x4>,
 			      <0x80010 0x4>,
 			      <0x80014 0x4>;
@@ -1159,7 +1168,7 @@
 				#mbox-cells = <1>;
 				ti,mbox-num-users = <4>;
 				ti,mbox-num-fifos = <8>;
-				mbox_wkupm3: wkup_m3 {
+				mbox_wkupm3: mbox-wkup-m3 {
 					ti,mbox-send-noirq;
 					ti,mbox-tx = <0 0 0>;
 					ti,mbox-rx = <0 0 3>;
@@ -1169,7 +1178,6 @@
 
 		target-module@ca000 {			/* 0x480ca000, ap 77 38.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spinlock";
 			reg = <0xca000 0x4>,
 			      <0xca010 0x4>,
 			      <0xca014 0x4>;
@@ -1198,7 +1206,7 @@
 	};
 
 	segment@100000 {					/* 0x48100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0008c000 0x0018c000 0x001000>,	/* ap 34 */
@@ -1282,7 +1290,6 @@
 
 		target-module@a0000 {			/* 0x481a0000, ap 67 2c.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi1";
 			reg = <0xa0000 0x4>,
 			      <0xa0110 0x4>,
 			      <0xa0114 0x4>;
@@ -1313,7 +1320,6 @@
 
 		target-module@a2000 {			/* 0x481a2000, ap 69 2e.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi2";
 			reg = <0xa2000 0x4>,
 			      <0xa2110 0x4>,
 			      <0xa2114 0x4>;
@@ -1344,7 +1350,6 @@
 
 		target-module@a4000 {			/* 0x481a4000, ap 92 62.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi3";
 			reg = <0xa4000 0x4>,
 			      <0xa4110 0x4>,
 			      <0xa4114 0x4>;
@@ -1394,7 +1399,7 @@
 			ranges = <0x0 0xa6000 0x1000>;
 
 			uart3: serial@0 {
-				compatible = "ti,am4372-uart","ti,omap2-uart";
+				compatible = "ti,am4372-uart";
 				reg = <0x0 0x2000>;
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -1422,7 +1427,7 @@
 			ranges = <0x0 0xa8000 0x1000>;
 
 			uart4: serial@0 {
-				compatible = "ti,am4372-uart","ti,omap2-uart";
+				compatible = "ti,am4372-uart";
 				reg = <0x0 0x2000>;
 				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -1450,7 +1455,7 @@
 			ranges = <0x0 0xaa000 0x1000>;
 
 			uart5: serial@0 {
-				compatible = "ti,am4372-uart","ti,omap2-uart";
+				compatible = "ti,am4372-uart";
 				reg = <0x0 0x2000>;
 				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -1527,7 +1532,6 @@
 
 		target-module@c1000 {			/* 0x481c1000, ap 94 68.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer8";
 			reg = <0xc1000 0x4>,
 			      <0xc1010 0x4>,
 			      <0xc1014 0x4>;
@@ -1556,10 +1560,10 @@
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0xcc020 0x4>;
 			reg-names = "rev";
-			ti,hwmods = "d_can0";
 			/* Domains (P, C): per_pwrdm, l4ls_clkdm */
-			clocks = <&l4ls_clkctrl AM4_L4LS_D_CAN0_CLKCTRL 0>;
-			clock-names = "fck";
+			clocks = <&l4ls_clkctrl AM4_L4LS_D_CAN0_CLKCTRL 0>,
+			<&dcan0_fck>;
+			clock-names = "fck", "osc";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0xcc000 0x2000>;
@@ -1567,6 +1571,8 @@
 			dcan0: can@0 {
 				compatible = "ti,am4372-d_can", "ti,am3352-d_can";
 				reg = <0x0 0x2000>;
+				clocks = <&dcan0_fck>;
+				clock-names = "fck";
 				syscon-raminit = <&scm_conf 0x644 0>;
 				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -1577,10 +1583,10 @@
 			compatible = "ti,sysc-omap4", "ti,sysc";
 			reg = <0xd0020 0x4>;
 			reg-names = "rev";
-			ti,hwmods = "d_can1";
 			/* Domains (P, C): per_pwrdm, l4ls_clkdm */
-			clocks = <&l4ls_clkctrl AM4_L4LS_D_CAN1_CLKCTRL 0>;
-			clock-names = "fck";
+			clocks = <&l4ls_clkctrl AM4_L4LS_D_CAN1_CLKCTRL 0>,
+			<&dcan1_fck>;
+			clock-names = "fck", "osc";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0xd0000 0x2000>;
@@ -1588,6 +1594,8 @@
 			dcan1: can@0 {
 				compatible = "ti,am4372-d_can", "ti,am3352-d_can";
 				reg = <0x0 0x2000>;
+				clocks = <&dcan1_fck>;
+				clock-names = "fck";
 				syscon-raminit = <&scm_conf 0x644 1>;
 				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
@@ -1616,7 +1624,7 @@
 			ranges = <0x0 0xd8000 0x1000>;
 
 			mmc2: mmc@0 {
-				compatible = "ti,omap4-hsmmc";
+				compatible = "ti,am437-sdhci";
 				reg = <0x0 0x1000>;
 				ti,needs-special-reset;
 				dmas = <&edma 2 0>,
@@ -1629,13 +1637,31 @@
 	};
 
 	segment@200000 {					/* 0x48200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
+		ranges = <0x00000000 0x00200000 0x010000>;
+
+		target-module@0 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			power-domains = <&prm_mpu>;
+			clocks = <&mpu_clkctrl AM4_MPU_MPU_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x10000>;
+
+			mpu@0 {
+				compatible = "ti,omap4-mpu";
+				pm-sram = <&pm_sram_code
+					   &pm_sram_data>;
+			};
+		};
 	};
 
 	segment@300000 {					/* 0x48300000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00300000 0x001000>,	/* ap 56 */
@@ -1695,7 +1721,6 @@
 
 		target-module@0 {			/* 0x48300000, ap 56 40.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss0";
 			reg = <0x0 0x4>,
 			      <0x4 0x4>;
 			reg-names = "rev", "sysc";
@@ -1722,10 +1747,9 @@
 				ranges = <0 0 0x1000>;
 				status = "disabled";
 
-				ecap0: ecap@100 {
+				ecap0: pwm@100 {
 					compatible = "ti,am4372-ecap",
-						     "ti,am3352-ecap",
-						     "ti,am33xx-ecap";
+						     "ti,am3352-ecap";
 					#pwm-cells = <3>;
 					reg = <0x100 0x80>;
 					clocks = <&l4ls_gclk>;
@@ -1735,8 +1759,7 @@
 
 				ehrpwm0: pwm@200 {
 					compatible = "ti,am4372-ehrpwm",
-						     "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+						     "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
@@ -1748,7 +1771,6 @@
 
 		target-module@2000 {			/* 0x48302000, ap 58 4a.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss1";
 			reg = <0x2000 0x4>,
 			      <0x2004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1775,10 +1797,9 @@
 				ranges = <0 0 0x1000>;
 				status = "disabled";
 
-				ecap1: ecap@100 {
+				ecap1: pwm@100 {
 					compatible = "ti,am4372-ecap",
-						     "ti,am3352-ecap",
-						     "ti,am33xx-ecap";
+						     "ti,am3352-ecap";
 					#pwm-cells = <3>;
 					reg = <0x100 0x80>;
 					clocks = <&l4ls_gclk>;
@@ -1788,8 +1809,7 @@
 
 				ehrpwm1: pwm@200 {
 					compatible = "ti,am4372-ehrpwm",
-						     "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+						     "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
@@ -1801,7 +1821,6 @@
 
 		target-module@4000 {			/* 0x48304000, ap 60 44.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss2";
 			reg = <0x4000 0x4>,
 			      <0x4004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1828,10 +1847,9 @@
 				ranges = <0 0 0x1000>;
 				status = "disabled";
 
-				ecap2: ecap@100 {
+				ecap2: pwm@100 {
 					compatible = "ti,am4372-ecap",
-						     "ti,am3352-ecap",
-						     "ti,am33xx-ecap";
+						     "ti,am3352-ecap";
 					#pwm-cells = <3>;
 					reg = <0x100 0x80>;
 					clocks = <&l4ls_gclk>;
@@ -1841,8 +1859,7 @@
 
 				ehrpwm2: pwm@200 {
 					compatible = "ti,am4372-ehrpwm",
-						     "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+						     "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
@@ -1854,7 +1871,6 @@
 
 		target-module@6000 {			/* 0x48306000, ap 96 58.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss3";
 			reg = <0x6000 0x4>,
 			      <0x6004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1883,8 +1899,7 @@
 
 				ehrpwm3: pwm@200 {
 					compatible = "ti,am4372-ehrpwm",
-						     "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+						     "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm3_tbclk>, <&l4ls_gclk>;
@@ -1896,7 +1911,6 @@
 
 		target-module@8000 {			/* 0x48308000, ap 98 54.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss4";
 			reg = <0x8000 0x4>,
 			      <0x8004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1925,8 +1939,7 @@
 
 				ehrpwm4: pwm@48308200 {
 					compatible = "ti,am4372-ehrpwm",
-						     "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+						     "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm4_tbclk>, <&l4ls_gclk>;
@@ -1938,7 +1951,6 @@
 
 		target-module@a000 {			/* 0x4830a000, ap 100 60.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss5";
 			reg = <0xa000 0x4>,
 			      <0xa004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1967,8 +1979,7 @@
 
 				ehrpwm5: pwm@200 {
 					compatible = "ti,am4372-ehrpwm",
-						     "ti,am3352-ehrpwm",
-						     "ti,am33xx-ehrpwm";
+						     "ti,am3352-ehrpwm";
 					#pwm-cells = <3>;
 					reg = <0x200 0x80>;
 					clocks = <&ehrpwm5_tbclk>, <&l4ls_gclk>;
@@ -2050,7 +2061,7 @@
 			};
 		};
 
-		target-module@22000 {			/* 0x48322000, ap 116 64.0 */
+		gpio5_target: target-module@22000 {		/* 0x48322000, ap 116 64.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x22000 0x4>,
 			      <0x22010 0x4>,
@@ -2086,7 +2097,6 @@
 
 		target-module@26000 {			/* 0x48326000, ap 86 66.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "vpfe0";
 			reg = <0x26000 0x4>,
 			      <0x26104 0x4>;
 			reg-names = "rev", "sysc";
@@ -2113,7 +2123,6 @@
 
 		target-module@28000 {			/* 0x48328000, ap 75 0e.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "vpfe1";
 			reg = <0x28000 0x4>,
 			      <0x28104 0x4>;
 			reg-names = "rev", "sysc";
@@ -2140,7 +2149,6 @@
 
 		target-module@2a000 {			/* 0x4832a000, ap 88 3c.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "dss_core";
 			reg = <0x2a000 0x4>,
 			      <0x2a010 0x4>,
 			      <0x2a014 0x4>;
@@ -2158,11 +2166,86 @@
 				 <0x00000800 0x0002a800 0x00000400>,
 				 <0x00000c00 0x0002ac00 0x00000400>,
 				 <0x00001000 0x0002b000 0x00001000>;
+
+			dss: dss@0 {
+				compatible = "ti,omap3-dss";
+				reg = <0 0x200>;
+				status = "disabled";
+				clocks = <&disp_clk>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x00000000 0x00000000 0x00000400>,
+					 <0x00000400 0x00000400 0x00000400>,
+					 <0x00000800 0x00000800 0x00000400>,
+					 <0x00000c00 0x00000c00 0x00000400>,
+					 <0x00001000 0x00001000 0x00001000>;
+
+				target-module@400 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x400 0x4>,
+					      <0x410 0x4>,
+					      <0x414 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-midle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&dss_clkctrl AM4_DSS_DSS_CORE_CLKCTRL 0>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x400 0x400>;
+
+					dispc: dispc@0 {
+						compatible = "ti,omap3-dispc";
+						reg = <0 0x400>;
+						interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+						clocks = <&disp_clk>;
+						clock-names = "fck";
+
+						max-memory-bandwidth = <230000000>;
+					};
+				};
+
+				target-module@800 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x800 0x4>,
+					      <0x810 0x4>,
+					      <0x814 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&dss_clkctrl AM4_DSS_DSS_CORE_CLKCTRL 0>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x800 0x400>;
+
+					rfbi: rfbi@0 {
+						compatible = "ti,omap3-rfbi";
+						reg = <0 0x100>;
+						clocks = <&dss_clkctrl AM4_DSS_DSS_CORE_CLKCTRL 0>;
+						clock-names = "fck";
+						status = "disabled";
+					};
+				};
+			};
 		};
 
 		target-module@3d000 {			/* 0x4833d000, ap 102 6e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer9";
 			reg = <0x3d000 0x4>,
 			      <0x3d010 0x4>,
 			      <0x3d014 0x4>;
@@ -2189,7 +2272,6 @@
 
 		target-module@3f000 {			/* 0x4833f000, ap 104 5c.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer10";
 			reg = <0x3f000 0x4>,
 			      <0x3f010 0x4>,
 			      <0x3f014 0x4>;
@@ -2216,7 +2298,6 @@
 
 		target-module@41000 {			/* 0x48341000, ap 106 76.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer11";
 			reg = <0x41000 0x4>,
 			      <0x41010 0x4>,
 			      <0x41014 0x4>;
@@ -2243,7 +2324,6 @@
 
 		target-module@45000 {			/* 0x48345000, ap 108 6a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spi4";
 			reg = <0x45000 0x4>,
 			      <0x45110 0x4>,
 			      <0x45114 0x4>;
@@ -2298,16 +2378,42 @@
 		};
 
 		target-module@4c000 {			/* 0x4834c000, ap 114 72.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x4c000 0x4>,
+			      <0x4c010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3s_clkctrl AM4_L3S_ADC1_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x4c000 0x2000>;
+
+			magadc: magadc@0 {
+				compatible = "ti,am4372-magadc";
+				reg = <0x0 0x2000>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&adc_mag_fck>;
+				clock-names = "fck";
+				dmas = <&edma 54 0>, <&edma 55 0>;
+				dma-names = "fifo0", "fifo1";
+				status = "disabled";
+
+				mag {
+					compatible = "ti,am4372-mag";
+				};
+
+				adc {
+					#io-channel-cells = <1>;
+					compatible = "ti,am4372-adc";
+				};
+			};
 		};
 
 		target-module@80000 {			/* 0x48380000, ap 123 42.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss0";
 			reg = <0x80000 0x4>,
 			      <0x80010 0x4>;
 			reg-names = "rev", "sysc";
@@ -2337,7 +2443,7 @@
 				ranges = <0 0 0x20000>;
 
 				usb1: usb@10000 {
-					compatible = "synopsys,dwc3";
+					compatible = "snps,dwc3";
 					reg = <0x10000 0x10000>;
 					interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
 						     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
@@ -2358,7 +2464,6 @@
 
 		target-module@a8000 {			/* 0x483a8000, ap 125 6c.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "ocp2scp0";
 			reg = <0xa8000 0x4>;
 			reg-names = "rev";
 			/* Domains (P, C): per_pwrdm, l4ls_clkdm */
@@ -2389,7 +2494,6 @@
 
 		target-module@c0000 {			/* 0x483c0000, ap 127 7a.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss1";
 			reg = <0xc0000 0x4>,
 			      <0xc0010 0x4>;
 			reg-names = "rev", "sysc";
@@ -2419,7 +2523,7 @@
 				ranges = <0 0 0x20000>;
 
 				usb2: usb@10000 {
-					compatible = "synopsys,dwc3";
+					compatible = "snps,dwc3";
 					reg = <0x10000 0x10000>;
 					interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
 						     <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
@@ -2440,7 +2544,6 @@
 
 		target-module@e8000 {			/* 0x483e8000, ap 129 78.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "ocp2scp1";
 			reg = <0xe8000 0x4>;
 			reg-names = "rev";
 			/* Domains (P, C): per_pwrdm, l4ls_clkdm */
diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts b/arch/arm/boot/dts/ti/omap/am437x-sbc-t43.dts
index 94cf07ea27f7..34a5407bee15 100644
--- a/arch/arm/boot/dts/am437x-sbc-t43.dts
+++ b/arch/arm/boot/dts/ti/omap/am437x-sbc-t43.dts
@@ -16,7 +16,7 @@
 };
 
 &am43xx_pinmux {
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
 			AM4372_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
@@ -29,7 +29,7 @@
 		>;
 	};
 
-	dss_pinctrl_default: dss_pinctrl_default {
+	dss_pinctrl_default: dss-pinctrl-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9b0, PIN_OUTPUT_PULLUP | MUX_MODE2) /* cam0 hd -> DSS DATA 23 */
 			AM4372_IOPAD(0x9b4, PIN_OUTPUT_PULLUP | MUX_MODE2)
@@ -64,7 +64,7 @@
 		>;
 	};
 
-	uart0_pins_default: uart0_pins_default {
+	uart0_pins_default: uart0-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0)
 			AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0)
@@ -73,27 +73,27 @@
 		>;
 	};
 
-	i2c1_pins: i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa6c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE1)  /* spi2_cs0.i2c1_sda  */
 			AM4372_IOPAD(0xa60, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE1)  /* spi2_sclk.i2c1_scl */
 		>;
 	};
 
-	i2c2_pins: i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE3)  /* uart1_ctsn.i2c2_sda  */
 			AM4372_IOPAD(0x97c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE3)  /* uart1_rtsn.i2c2_scl */
 		>;
 	};
 
-	usb2_phy1_default: usb2_phy1_default {
+	usb2_phy1_default: usb2-phy1-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xac0, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE0)
 		>;
 	};
 
-	usb2_phy2_default: usb2_phy2_default {
+	usb2_phy2_default: usb2-phy2-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xac4, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE0)
 		>;
@@ -136,7 +136,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_pinctrl_default>;
diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/ti/omap/am437x-sk-evm.dts
index 74eaa6a3b258..9c97006ffd5b 100644
--- a/arch/arm/boot/dts/am437x-sk-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am437x-sk-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /* AM437x SK EVM */
@@ -134,22 +134,6 @@
 
 		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 
-		panel-timing {
-			clock-frequency = <9000000>;
-			hactive = <480>;
-			vactive = <272>;
-			hfront-porch = <2>;
-			hback-porch = <2>;
-			hsync-len = <41>;
-			vfront-porch = <2>;
-			vback-porch = <2>;
-			vsync-len = <10>;
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-
 		port {
 			lcd_in: endpoint {
 				remote-endpoint = <&dpi_out>;
@@ -175,7 +159,7 @@
 };
 
 &am43xx_pinmux {
-	matrix_keypad_pins: matrix_keypad_pins {
+	matrix_keypad_pins: matrix-keypad-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa4c, PIN_OUTPUT | MUX_MODE7)	/* gpio5_13.gpio5_13 */
 			AM4372_IOPAD(0xa50, PIN_OUTPUT | MUX_MODE7)	/* spi4_sclk.gpio5_4 */
@@ -184,7 +168,7 @@
 		>;
 	};
 
-	leds_pins: leds_pins {
+	leds_pins: leds-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xa28, PIN_OUTPUT | MUX_MODE7)	/* uart3_rxd.gpio5_2 */
 			AM4372_IOPAD(0xa2c, PIN_OUTPUT | MUX_MODE7)	/* uart3_txd.gpio5_3 */
@@ -193,21 +177,21 @@
 		>;
 	};
 
-	i2c0_pins: i2c0_pins {
+	i2c0_pins: i2c0-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x988, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
 			AM4372_IOPAD(0x98c, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
 		>;
 	};
 
-	i2c1_pins: i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x95c, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
 			AM4372_IOPAD(0x958, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x8f0, PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
 			AM4372_IOPAD(0x8f4, PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
@@ -219,20 +203,20 @@
 		>;
 	};
 
-	ecap0_pins: backlight_pins {
+	ecap0_pins: backlight-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x964, PIN_OUTPUT | MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out */
 		>;
 	};
 
-	edt_ft5306_ts_pins: edt_ft5306_ts_pins {
+	edt_ft5306_ts_pins: edt-ft5306-ts-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x874, PIN_INPUT | MUX_MODE7)	/* gpmc_wpn.gpio0_31 */
 			AM4372_IOPAD(0x878, PIN_OUTPUT | MUX_MODE7)	/* gpmc_be1n.gpio1_28 */
 		>;
 	};
 
-	vpfe0_pins_default: vpfe0_pins_default {
+	vpfe0_pins_default: vpfe0-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_hd mode 0*/
 			AM4372_IOPAD(0x9b4, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_vd mode 0*/
@@ -252,7 +236,7 @@
 		>;
 	};
 
-	vpfe0_pins_sleep: vpfe0_pins_sleep {
+	vpfe0_pins_sleep: vpfe0-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9b0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
 			AM4372_IOPAD(0x9b4, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
@@ -272,7 +256,13 @@
 		>;
 	};
 
-	cpsw_default: cpsw_default {
+	clkout1_pin: clkout1-pins {
+		pinctrl-single,pins = <
+			0x270 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* XDMA_EVENT_INTR0/CLKOUT1 */
+		>;
+	};
+
+	cpsw_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			AM4372_IOPAD(0x92c, PIN_OUTPUT | MUX_MODE2)	/* mii1_txclk.rmii1_tclk */
@@ -304,7 +294,7 @@
 		>;
 	};
 
-	cpsw_sleep: cpsw_sleep {
+	cpsw_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 reset value */
 			AM4372_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -336,7 +326,7 @@
 		>;
 	};
 
-	davinci_mdio_default: davinci_mdio_default {
+	davinci_mdio_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			AM4372_IOPAD(0x948, PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
@@ -344,7 +334,7 @@
 		>;
 	};
 
-	davinci_mdio_sleep: davinci_mdio_sleep {
+	davinci_mdio_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			/* MDIO reset value */
 			AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -352,7 +342,7 @@
 		>;
 	};
 
-	dss_pins: dss_pins {
+	dss_pins: dss-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x820, PIN_OUTPUT | MUX_MODE1)	/* gpmc ad 8 -> DSS DATA 23 */
 			AM4372_IOPAD(0x824, PIN_OUTPUT | MUX_MODE1)
@@ -386,7 +376,7 @@
 		>;
 	};
 
-	qspi_pins: qspi_pins {
+	qspi_pins: qspi-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE3)	/* gpmc_csn0.qspi_csn */
 			AM4372_IOPAD(0x888, PIN_OUTPUT | MUX_MODE2)	/* gpmc_csn3.qspi_clk */
@@ -397,7 +387,7 @@
 		>;
 	};
 
-	mcasp1_pins: mcasp1_pins {
+	mcasp1_pins: mcasp1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* mii1_crs.mcasp1_aclkx */
 			AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* mii1_rxerr.mcasp1_fsx */
@@ -406,7 +396,7 @@
 		>;
 	};
 
-	mcasp1_pins_sleep: mcasp1_pins_sleep {
+	mcasp1_pins_sleep: mcasp1-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7)
 			AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -415,25 +405,25 @@
 		>;
 	};
 
-	lcd_pins: lcd_pins {
+	lcd_pins: lcd-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x81c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpcm_ad7.gpio1_7 */
 		>;
 	};
 
-	usb1_pins: usb1_pins {
+	usb1_pins: usb1-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xac0, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
 		>;
 	};
 
-	usb2_pins: usb2_pins {
+	usb2_pins: usb2-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
 		>;
 	};
 
-	mmc3_pins_default: pinmux_mmc3_pins_default {
+	mmc3_pins_default: mmc3-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD21) cam1_data2.mmc2_clk */
 			AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE22) cam1_data3.mmc2_cmd */
@@ -444,7 +434,7 @@
 		>;
 	};
 
-	mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+	mmc3_pins_sleep: mmc3-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD21) cam1_data2.mmc2_clk */
 			AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE22) cam1_data3.mmc2_cmd */
@@ -455,21 +445,21 @@
 		>;
 	};
 
-	wlan_pins_default: pinmux_wlan_pins_default {
+	wlan_pins_default: wlan-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* cam1_data8.gpio4_8 WL_EN */
 			AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* cam1_wen.gpio4_13 WL_IRQ */
 		>;
 	};
 
-	wlan_pins_sleep: pinmux_wlan_pins_sleep {
+	wlan_pins_sleep: wlan-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* cam1_data8.gpio4_8 WL_EN */
 			AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* cam1_wen.gpio4_13 WL_IRQ */
 		>;
 	};
 
-	uart1_bt_pins_default: pinmux_uart1_bt_pins_default {
+	uart1_bt_pins_default: uart1-bt-default-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x980, PIN_INPUT | MUX_MODE0)		/* uart1_rxd.uart1_rxd */
 			AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
@@ -479,7 +469,7 @@
 		>;
 	};
 
-	uart1_bt_pins_sleep: pinmux_uart1_bt_pins_sleep {
+	uart1_bt_pins_sleep: uart1-bt-sleep-pins {
 		pinctrl-single,pins = <
 			AM4372_IOPAD(0x980, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart1_rxd.uart1_rxd */
 			AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart1_txd.uart1_txd */
@@ -593,6 +583,25 @@
 	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <400000>;
 
+	ov2659@30 {
+		compatible = "ovti,ov2659";
+		reg = <0x30>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clkout1_pin>;
+
+		clocks = <&clkout1_mux_ck>;
+		clock-names = "xvclk";
+		assigned-clocks = <&clkout1_mux_ck>;
+		assigned-clock-parents = <&clkout1_osc_div_ck>;
+
+		port {
+			ov2659_1: endpoint {
+				remote-endpoint = <&vpfe0_ep>;
+				link-frequencies = /bits/ 64 <70000000>;
+			};
+		};
+	};
+
 	edt-ft5306@38 {
 		status = "okay";
 		compatible = "edt,edt-ft5306", "edt,edt-ft5x06";
@@ -694,7 +703,7 @@
 	pinctrl-1 = <&mmc3_pins_sleep>;
 	cap-power-off-card;
 	keep-power-in-suspend;
-	ti,non-removable;
+	non-removable;
 
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -737,7 +746,7 @@
 	pinctrl-0 = <&qspi_pins>;
 
 	spi-max-frequency = <48000000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx66l51235l";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
@@ -754,7 +763,7 @@
 		 */
 		partition@0 {
 			label = "QSPI.U_BOOT";
-			reg = <0x00000000 0x000080000>;
+			reg = <0x00000000 0x00080000>;
 		};
 		partition@1 {
 			label = "QSPI.U_BOOT.backup";
@@ -783,19 +792,17 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@4 {
 		reg = <4>;
@@ -806,16 +813,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <2>;
 };
 
 &elm {
@@ -877,7 +884,7 @@
 	/* Camera port */
 	port {
 		vpfe0_ep: endpoint {
-			/* remote-endpoint = <&sensor>; add once we have it */
+			remote-endpoint = <&ov2659_1>;
 			ti,am437x-vpfe-interface = <0>;
 			bus-width = <8>;
 			hsync-active = <0>;
@@ -885,3 +892,11 @@
 		};
 	};
 };
+
+&wkup_m3_ipc {
+	firmware-name = "am43x-evm-scale-data.bin";
+};
+
+&pruss1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/ti/omap/am43x-epos-evm.dts
index 95314121d111..9193a4cfba78 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/am43x-epos-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /* AM43x EPOS EVM */
@@ -11,7 +11,7 @@
 #include <dt-bindings/pinctrl/am43xx.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pwm/pwm.h>
-#include <dt-bindings/sound/tlv320aic31xx-micbias.h>
+#include <dt-bindings/sound/tlv320aic31xx.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
@@ -42,27 +42,11 @@
 	};
 
 	lcd0: display {
-		compatible = "osddisplays,osd057T0559-34ts", "panel-dpi";
+		compatible = "osddisplays,osd070t1718-19ts", "panel-dpi";
 		label = "lcd";
 
 		backlight = <&lcd_bl>;
 
-		panel-timing {
-			clock-frequency = <33000000>;
-			hactive = <800>;
-			vactive = <480>;
-			hfront-porch = <210>;
-			hback-porch = <16>;
-			hsync-len = <30>;
-			vback-porch = <10>;
-			vfront-porch = <22>;
-			vsync-len = <13>;
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-
 		port {
 			lcd_in: endpoint {
 				remote-endpoint = <&dpi_out>;
@@ -145,13 +129,19 @@
 			system-clock-frequency = <12000000>;
 		};
 	};
+
+	audio_mstrclk: clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12000000>;
+	};
 };
 
 &am43xx_pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&unused_pins>;
 
-		unused_pins: unused_pins {
+		unused_pins: unused-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x848, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
 				AM4372_IOPAD(0x850, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -185,7 +175,7 @@
 			>;
 		};
 
-		cpsw_default: cpsw_default {
+		cpsw_default: cpsw-default-pins {
 			pinctrl-single,pins = <
 				/* Slave 1 */
 				AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_crs.rmii1_crs */
@@ -200,7 +190,7 @@
 			>;
 		};
 
-		cpsw_sleep: cpsw_sleep {
+		cpsw_sleep: cpsw-sleep-pins {
 			pinctrl-single,pins = <
 				/* Slave 1 reset value */
 				AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -215,7 +205,7 @@
 			>;
 		};
 
-		davinci_mdio_default: davinci_mdio_default {
+		davinci_mdio_default: davinci-mdio-default-pins {
 			pinctrl-single,pins = <
 				/* MDIO */
 				AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
@@ -223,7 +213,7 @@
 			>;
 		};
 
-		davinci_mdio_sleep: davinci_mdio_sleep {
+		davinci_mdio_sleep: davinci-mdio-sleep-pins {
 			pinctrl-single,pins = <
 				/* MDIO reset value */
 				AM4372_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -231,14 +221,14 @@
 			>;
 		};
 
-		i2c0_pins: pinmux_i2c0_pins {
+		i2c0_pins: i2c0-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
 				AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			>;
 		};
 
-		nand_flash_x8_default: nand_flash_x8_default {
+		nand_flash_x8_default: nand-flash-x8-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.SELQSPIorNAND/GPIO */
 				AM4372_IOPAD(0x800, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
@@ -259,7 +249,7 @@
 			>;
 		};
 
-		nand_flash_x8_sleep: nand_flash_x8_sleep {
+		nand_flash_x8_sleep: nand-flash-x8-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x840, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
 				AM4372_IOPAD(0x800, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
@@ -280,26 +270,26 @@
 			>;
 		};
 
-		ecap0_pins_default: backlight_pins_default {
+		ecap0_pins_default: backlight-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x964, MUX_MODE0)         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
 			>;
 		};
 
-		ecap0_pins_sleep: backlight_pins_sleep {
+		ecap0_pins_sleep: backlight-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x964, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
 			>;
 		};
 
-		i2c2_pins: pinmux_i2c2_pins {
+		i2c2_pins: i2c2-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9c0, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_sda.i2c2_sda */
 				AM4372_IOPAD(0x9c4, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_scl.i2c2_scl */
 			>;
 		};
 
-		spi0_pins_default: pinmux_spi0_pins_default {
+		spi0_pins_default: spi0-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0)           /* spi0_clk.spi0_clk */
 				AM4372_IOPAD(0x954, PIN_OUTPUT | MUX_MODE0)           /* spi0_d0.spi0_d0 */
@@ -308,7 +298,7 @@
 			>;
 		};
 
-		spi0_pins_sleep: pinmux_spi0_pins_sleep {
+		spi0_pins_sleep: spi0-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x950, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
 				AM4372_IOPAD(0x954, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
@@ -317,7 +307,7 @@
 			>;
 		};
 
-		spi1_pins_default: pinmux_spi1_pins_default {
+		spi1_pins_default: spi1-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x990, PIN_INPUT | MUX_MODE3)           /* mcasp0_aclkx.spi1_clk */
 				AM4372_IOPAD(0x994, PIN_OUTPUT | MUX_MODE3)           /* mcasp0_fsx.spi1_d0 */
@@ -326,7 +316,7 @@
 			>;
 		};
 
-		spi1_pins_sleep: pinmux_spi1_pins_sleep {
+		spi1_pins_sleep: spi1-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x990, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
 				AM4372_IOPAD(0x994, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
@@ -335,19 +325,19 @@
 			>;
 		};
 
-		mmc1_pins_default: pinmux_mmc1_pins_default {
+		mmc1_pins_default: mmc1-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
 			>;
 		};
 
-		mmc1_pins_sleep: pinmux_mmc1_pins_sleep {
+		mmc1_pins_sleep: mmc1-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x960, DS0_PIN_OUTPUT_PULLUP | PIN_INPUT | MUX_MODE7)
 			>;
 		};
 
-		matrix_keypad_default: matrix_keypad_default {
+		matrix_keypad_default: matrix-keypad-default-pins {
 			pinctrl-single,pins = <
 				 AM4372_IOPAD(0x92c, PIN_OUTPUT | MUX_MODE7)          /* mii1_tx_clk.gpio3_9 */
 				 AM4372_IOPAD(0x930, PIN_OUTPUT | MUX_MODE7)          /* mii1_rx_clk.gpio3_10 */
@@ -360,7 +350,7 @@
 			>;
 		};
 
-		matrix_keypad_sleep: matrix_keypad_sleep {
+		matrix_keypad_sleep: matrix-keypad-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE7)
 				AM4372_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE7)
@@ -373,7 +363,7 @@
 			>;
 		};
 
-		qspi1_pins_default: qspi1_pins_default {
+		qspi1_pins_default: qspi1-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x87c, PIN_INPUT_PULLUP | MUX_MODE3)
 				AM4372_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE2)
@@ -384,7 +374,7 @@
 			>;
 		};
 
-		qspi1_pins_sleep: qspi1_pins_sleep {
+		qspi1_pins_sleep: qspi1-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x87c, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
 				AM4372_IOPAD(0x888, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
@@ -395,25 +385,25 @@
 			>;
 		};
 
-		pixcir_ts_pins_default: pixcir_ts_pins_default {
+		pixcir_ts_pins_default: pixcir-ts-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
 			>;
 		};
 
-		pixcir_ts_pins_sleep: pixcir_ts_pins_sleep {
+		pixcir_ts_pins_sleep: pixcir-ts-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x844, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
 			>;
 		};
 
-		hdq_pins: pinmux_hdq_pins {
+		hdq_pins: hdq-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0xa34, PIN_INPUT_PULLUP | MUX_MODE1)    /* cam1_wen.hdq_gpio */
 			>;
 		};
 
-		dss_pins: dss_pins {
+		dss_pins: dss-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x820, PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */
 				AM4372_IOPAD(0x824, PIN_OUTPUT_PULLUP | MUX_MODE1)
@@ -446,14 +436,14 @@
 			>;
 		};
 
-		display_mux_pins: display_mux_pins {
+		display_mux_pins: display-mux-pins {
 			pinctrl-single,pins = <
 				/* GPMC CLK -> GPIO 2_1 to select LCD / HDMI */
 				AM4372_IOPAD(0x88C, PIN_OUTPUT_PULLUP | MUX_MODE7)
 			>;
 		};
 
-		vpfe1_pins_default: vpfe1_pins_default {
+		vpfe1_pins_default: vpfe1-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9cc, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data9 mode 0 */
 				AM4372_IOPAD(0x9d0, PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data8 mode 0 */
@@ -471,7 +461,7 @@
 			>;
 		};
 
-		vpfe1_pins_sleep: vpfe1_pins_sleep {
+		vpfe1_pins_sleep: vpfe1-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9cc, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
 				AM4372_IOPAD(0x9d0, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
@@ -489,7 +479,7 @@
 			>;
 		};
 
-		uart0_pins_default: uart0_pins_default {
+		uart0_pins_default: uart0-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) /* uart0_ctsn.uart0_ctsn */
 				AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) /* uart0_rtsn.uart0_rtsn */
@@ -498,7 +488,7 @@
 			>;
 		};
 
-		uart0_pins_sleep: uart0_pins_sleep {
+		uart0_pins_sleep: uart0-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
 				AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
@@ -507,31 +497,31 @@
 			>;
 		};
 
-		usb2_phy1_default: usb2_phy1_default {
+		usb2_phy1_default: usb2-phy1-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0xac0, PIN_INPUT_PULLDOWN | MUX_MODE0)
 			>;
 		};
 
-		usb2_phy1_sleep: usb2_phy1_sleep {
+		usb2_phy1_sleep: usb2-phy1-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0xac0, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE7)
 			>;
 		};
 
-		usb2_phy2_default: usb2_phy2_default {
+		usb2_phy2_default: usb2-phy2-default-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0xac4, PIN_INPUT_PULLDOWN | MUX_MODE0)
 			>;
 		};
 
-		usb2_phy2_sleep: usb2_phy2_sleep {
+		usb2_phy2_sleep: usb2-phy2-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0xac4, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE7)
 			>;
 		};
 
-		mcasp1_pins: mcasp1_pins {
+		mcasp1_pins: mcasp1-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_ACLKR/MCASP1_ACLKX */
 				AM4372_IOPAD(0x9a4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_FSR/MCASP1_FSX */
@@ -540,7 +530,7 @@
 			>;
 		};
 
-		mcasp1_sleep_pins: mcasp1_sleep_pins {
+		mcasp1_sleep_pins: mcasp1-sleep-pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE7)
 				AM4372_IOPAD(0x9a4, PIN_INPUT_PULLDOWN | MUX_MODE7)
@@ -560,36 +550,39 @@
 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	slaves = <1>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@16 {
 		reg = <16>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
 	phys = <&phy_gmii_sel 1 1>;
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 &i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
-	clock-frequency = <400000>;
+	clock-frequency = <100000>;
 
 	tps65218: tps65218@24 {
 		reg = <0x24>;
@@ -696,6 +689,21 @@
 		IOVDD-supply = <&dcdc4>; /* V3_3D -> DCDC4 */
 		DVDD-supply = <&ldo1>; /* V1_8AUD -> V1_8D -> LDO1 */
 	};
+
+	ov2659@30 {
+		compatible = "ovti,ov2659";
+		reg = <0x30>;
+
+		clocks = <&audio_mstrclk>;
+		clock-names = "xvclk";
+
+		port {
+			ov2659_1: endpoint {
+				remote-endpoint = <&vpfe1_ep>;
+				link-frequencies = /bits/ 64 <70000000>;
+			};
+		};
+	};
 };
 
 &i2c2 {
@@ -717,7 +725,7 @@
 	pinctrl-0 = <&display_mux_pins>;
 	status = "okay";
 
-	p1 {
+	sel-lcd-hdmi-hog {
 		/*
 		 * SelLCDorHDMI selects between display and audio paths:
 		 * Low: HDMI display with audio via HDMI
@@ -828,6 +836,10 @@
 	status = "okay";
 };
 
+&rtc_target {
+	status = "disabled";
+};
+
 &tscadc {
 	status = "okay";
 
@@ -848,6 +860,7 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&spi0_pins_default>;
 	pinctrl-1 = <&spi0_pins_sleep>;
+	ti,pindir-d0-out-d1-in;
 };
 
 &spi1 {
@@ -855,6 +868,7 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&spi1_pins_default>;
 	pinctrl-1 = <&spi1_pins_sleep>;
+	ti,pindir-d0-out-d1-in;
 };
 
 &usb2_phy1 {
@@ -888,7 +902,7 @@
 	pinctrl-1 = <&qspi1_pins_sleep>;
 
 	spi-max-frequency = <48000000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx66l51235l";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
@@ -905,7 +919,7 @@
 		 */
 		partition@0 {
 			label = "QSPI.U_BOOT";
-			reg = <0x00000000 0x000080000>;
+			reg = <0x00000000 0x00080000>;
 		};
 		partition@1 {
 			label = "QSPI.U_BOOT.backup";
@@ -941,7 +955,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_pins>;
@@ -962,7 +976,7 @@
 
 	port {
 		vpfe1_ep: endpoint {
-			/* remote-endpoint = <&sensor>; add once we have it */
+			remote-endpoint = <&ov2659_1>;
 			ti,am437x-vpfe-interface = <0>;
 			bus-width = <8>;
 			hsync-active = <0>;
@@ -1004,3 +1018,11 @@
 &cpu {
 	cpu0-supply = <&dcdc2>;
 };
+
+&wkup_m3_ipc {
+	firmware-name = "am43x-evm-scale-data.bin";
+};
+
+&pruss1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am43xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/am43xx-clocks.dtsi
index 091356f2a8c1..9a5437b3d6a8 100644
--- a/arch/arm/boot/dts/am43xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am43xx-clocks.dtsi
@@ -5,217 +5,246 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &scm_clocks {
-	sys_clkin_ck: sys_clkin_ck@40 {
+	sys_clkin_ck: clock-sys-clkin-31@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin_ck";
 		clocks = <&sysboot_freq_sel_ck>, <&crystal_freq_sel_ck>;
 		ti,bit-shift = <31>;
 		reg = <0x0040>;
 	};
 
-	crystal_freq_sel_ck: crystal_freq_sel_ck@40 {
+	crystal_freq_sel_ck: clock-crystal-freq-sel-29@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "crystal_freq_sel_ck";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
 		ti,bit-shift = <29>;
 		reg = <0x0040>;
 	};
 
-	sysboot_freq_sel_ck: sysboot_freq_sel_ck@44e10040 {
+	sysboot_freq_sel_ck: clock-sysboot-freq-sel-22@44e10040 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sysboot_freq_sel_ck";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
 		ti,bit-shift = <22>;
 		reg = <0x0040>;
 	};
 
-	adc_tsc_fck: adc_tsc_fck {
+	adc_tsc_fck: clock-adc-tsc-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "adc_tsc_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan0_fck: dcan0_fck {
+	dcan0_fck: clock-dcan0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan1_fck: dcan1_fck {
+	dcan1_fck: clock-dcan1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp0_fck: mcasp0_fck {
+	mcasp0_fck: clock-mcasp0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp1_fck: mcasp1_fck {
+	mcasp1_fck: clock-mcasp1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex0_fck: smartreflex0_fck {
+	smartreflex0_fck: clock-smartreflex0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex1_fck: smartreflex1_fck {
+	smartreflex1_fck: clock-smartreflex1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	sha0_fck: sha0_fck {
+	sha0_fck: clock-sha0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sha0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	aes0_fck: aes0_fck {
+	aes0_fck: clock-aes0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "aes0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	rng_fck: rng_fck {
+	rng_fck: clock-rng-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "rng_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	ehrpwm0_tbclk: ehrpwm0_tbclk@664 {
+	ehrpwm0_tbclk: clock-ehrpwm0-tbclk-0@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm0_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <0>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm1_tbclk: ehrpwm1_tbclk@664 {
+	ehrpwm1_tbclk: clock-ehrpwm1-tbclk-1@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm1_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <1>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm2_tbclk: ehrpwm2_tbclk@664 {
+	ehrpwm2_tbclk: clock-ehrpwm2-tbclk-2@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm2_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <2>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm3_tbclk: ehrpwm3_tbclk@664 {
+	ehrpwm3_tbclk: clock-ehrpwm3-tbclk-4@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm3_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <4>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm4_tbclk: ehrpwm4_tbclk@664 {
+	ehrpwm4_tbclk: clock-ehrpwm4-tbclk-5@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm4_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <5>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm5_tbclk: ehrpwm5_tbclk@664 {
+	ehrpwm5_tbclk: clock-ehrpwm5-tbclk-6@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm5_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <6>;
 		reg = <0x0664>;
 	};
 };
 &prcm_clocks {
-	clk_32768_ck: clk_32768_ck {
+	clk_32768_ck: clock-clk-32768 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32768_ck";
 		clock-frequency = <32768>;
 	};
 
-	clk_rc32k_ck: clk_rc32k_ck {
+	clk_rc32k_ck: clock-clk-rc32k {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_rc32k_ck";
 		clock-frequency = <32768>;
 	};
 
-	virt_19200000_ck: virt_19200000_ck {
+	virt_19200000_ck: clock-virt-19200000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
-	virt_24000000_ck: virt_24000000_ck {
+	virt_24000000_ck: clock-virt-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_24000000_ck";
 		clock-frequency = <24000000>;
 	};
 
-	virt_25000000_ck: virt_25000000_ck {
+	virt_25000000_ck: clock-virt-25000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_25000000_ck";
 		clock-frequency = <25000000>;
 	};
 
-	virt_26000000_ck: virt_26000000_ck {
+	virt_26000000_ck: clock-virt-26000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
-	tclkin_ck: tclkin_ck {
+	tclkin_ck: clock-tclkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "tclkin_ck";
 		clock-frequency = <26000000>;
 	};
 
-	dpll_core_ck: dpll_core_ck@2d20 {
+	dpll_core_ck: clock@2d20 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x2d20>, <0x2d24>, <0x2d2c>;
+		reg = <0x2d20>, <0x2d24>, <0x2d2c>, <0x2d48>, <0x2d4c>;
 	};
 
-	dpll_core_x2_ck: dpll_core_x2_ck {
+	dpll_core_x2_ck: clock-dpll-core-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_m4_ck: dpll_core_m4_ck@2d38 {
+	dpll_core_m4_ck: clock-dpll-core-m4-8@2d38 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m4_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -224,9 +253,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_m5_ck: dpll_core_m5_ck@2d3c {
+	dpll_core_m5_ck: clock-dpll-core-m5-8@2d3c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m5_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -235,9 +265,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_m6_ck: dpll_core_m6_ck@2d40 {
+	dpll_core_m6_ck: clock-dpll-core-m6-8@2d40 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m6_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -246,16 +277,18 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck@2d60 {
+	dpll_mpu_ck: clock@2d60 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x2d60>, <0x2d64>, <0x2d6c>;
+		reg = <0x2d60>, <0x2d64>, <0x2d6c>, <0x2d88>, <0x2d8c>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck@2d70 {
+	dpll_mpu_m2_ck: clock-dpll-mpu-m2-8@2d70 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -264,24 +297,27 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mpu_periphclk: mpu_periphclk {
+	mpu_periphclk: clock-mpu-periphclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_periphclk";
 		clocks = <&dpll_mpu_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck@2da0 {
+	dpll_ddr_ck: clock@2da0 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_ddr_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x2da0>, <0x2da4>, <0x2dac>;
+		reg = <0x2da0>, <0x2da4>, <0x2dac>, <0x2dc8>, <0x2dcc>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck@2db0 {
+	dpll_ddr_m2_ck: clock-dpll-ddr-m2-8@2db0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m2_ck";
 		clocks = <&dpll_ddr_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -290,16 +326,18 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_disp_ck: dpll_disp_ck@2e20 {
+	dpll_disp_ck: clock@2e20 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_disp_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x2e20>, <0x2e24>, <0x2e2c>;
+		reg = <0x2e20>, <0x2e24>, <0x2e2c>, <0x2e48>, <0x2e4c>;
 	};
 
-	dpll_disp_m2_ck: dpll_disp_m2_ck@2e30 {
+	dpll_disp_m2_ck: clock-dpll-disp-m2-8@2e30 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_disp_m2_ck";
 		clocks = <&dpll_disp_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -309,16 +347,18 @@
 		ti,set-rate-parent;
 	};
 
-	dpll_per_ck: dpll_per_ck@2de0 {
+	dpll_per_ck: clock@2de0 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-j-type-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x2de0>, <0x2de4>, <0x2dec>;
+		reg = <0x2de0>, <0x2de4>, <0x2dec>, <0x2e08>, <0x2e0c>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck@2df0 {
+	dpll_per_m2_ck: clock-dpll-per-m2-8@2df0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -327,242 +367,281 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+	dpll_per_m2_div4_wkupdm_ck: clock-dpll-per-m2-div4-wkupdm {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_wkupdm_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+	dpll_per_m2_div4_ck: clock-dpll-per-m2-div4 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	clk_24mhz: clk_24mhz {
+	clk_24mhz: clock-clk-24mhz {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clk_24mhz";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
 	};
 
-	clkdiv32k_ck: clkdiv32k_ck {
+	clkdiv32k_ck: clock-clkdiv32k {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clkdiv32k_ck";
 		clocks = <&clk_24mhz>;
 		clock-mult = <1>;
 		clock-div = <732>;
 	};
 
-	clkdiv32k_ick: clkdiv32k_ick@2a38 {
+	clkdiv32k_ick: clock-clkdiv32k-ick-8@2a38 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "clkdiv32k_ick";
 		clocks = <&clkdiv32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x2a38>;
 	};
 
-	sysclk_div: sysclk_div {
+	sysclk_div: clock-sysclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sysclk_div";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	pruss_ocp_gclk: pruss_ocp_gclk@4248 {
+	pruss_ocp_gclk: clock-pruss-ocp-gclk@4248 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "pruss_ocp_gclk";
 		clocks = <&sysclk_div>, <&dpll_disp_m2_ck>;
 		reg = <0x4248>;
 	};
 
-	clk_32k_tpm_ck: clk_32k_tpm_ck {
+	clk_32k_tpm_ck: clock-clk-32k-tpm {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32k_tpm_ck";
 		clock-frequency = <32768>;
 	};
 
-	timer1_fck: timer1_fck@4200 {
+	timer1_fck: clock-timer1-fck@4200 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer1_fck";
 		clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>, <&clk_32k_tpm_ck>;
 		reg = <0x4200>;
 	};
 
-	timer2_fck: timer2_fck@4204 {
+	timer2_fck: clock-timer2-fck@4204 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer2_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4204>;
 	};
 
-	timer3_fck: timer3_fck@4208 {
+	timer3_fck: clock-timer3-fck@4208 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer3_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4208>;
 	};
 
-	timer4_fck: timer4_fck@420c {
+	timer4_fck: clock-timer4-fck@420c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer4_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x420c>;
 	};
 
-	timer5_fck: timer5_fck@4210 {
+	timer5_fck: clock-timer5-fck@4210 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer5_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4210>;
 	};
 
-	timer6_fck: timer6_fck@4214 {
+	timer6_fck: clock-timer6-fck@4214 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer6_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4214>;
 	};
 
-	timer7_fck: timer7_fck@4218 {
+	timer7_fck: clock-timer7-fck@4218 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer7_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4218>;
 	};
 
-	wdt1_fck: wdt1_fck@422c {
+	wdt1_fck: clock-wdt1-fck@422c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wdt1_fck";
 		clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>;
 		reg = <0x422c>;
 	};
 
-	l3_gclk: l3_gclk {
+	adc_mag_fck: adc_mag_fck@424c {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin_ck>, <&dpll_per_m2_ck>;
+		reg = <0x424c>;
+	};
+
+	l3_gclk: clock-l3-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+	dpll_core_m4_div2_ck: clock-dpll-core-m4-div2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_core_m4_div2_ck";
 		clocks = <&sysclk_div>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l4hs_gclk: l4hs_gclk {
+	l4hs_gclk: clock-l4hs-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4hs_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l3s_gclk: l3s_gclk {
+	l3s_gclk: clock-l3s-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3s_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l4ls_gclk: l4ls_gclk {
+	l4ls_gclk: clock-l4ls-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4ls_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+	cpsw_125mhz_gclk: clock-cpsw-125mhz-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_125mhz_gclk";
 		clocks = <&dpll_core_m5_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk@4238 {
+	cpsw_cpts_rft_clk: clock-cpsw-cpts-rft@4238 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "cpsw_cpts_rft_clk";
 		clocks = <&sysclk_div>, <&dpll_core_m5_ck>, <&dpll_disp_m2_ck>;
 		reg = <0x4238>;
 	};
 
-	dpll_clksel_mac_clk: dpll_clksel_mac_clk@4234 {
+	dpll_clksel_mac_clk: clock-dpll-clksel-mac-2@4234 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_clksel_mac_clk";
 		clocks = <&dpll_core_m5_ck>;
 		reg = <0x4234>;
 		ti,bit-shift = <2>;
 		ti,dividers = <2>, <5>;
 	};
 
-	clk_32k_mosc_ck: clk_32k_mosc_ck {
+	clk_32k_mosc_ck: clock-clk-32k-mosc {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32k_mosc_ck";
 		clock-frequency = <32768>;
 	};
 
-	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck@4240 {
+	gpio0_dbclk_mux_ck: clock-gpio0-dbclk-mux@4240 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpio0_dbclk_mux_ck";
 		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>, <&clk_32k_mosc_ck>, <&clk_32k_tpm_ck>;
 		reg = <0x4240>;
 	};
 
-	mmc_clk: mmc_clk {
+	mmc_clk: clock-mmc {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mmc_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck@423c {
+	gfx_fclk_clksel_ck: clock-gfx-fclk-clksel-1@423c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gfx_fclk_clksel_ck";
 		clocks = <&sysclk_div>, <&dpll_per_m2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x423c>;
 	};
 
-	gfx_fck_div_ck: gfx_fck_div_ck@423c {
+	gfx_fck_div_ck: clock-gfx-fck-div@423c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "gfx_fck_div_ck";
 		clocks = <&gfx_fclk_clksel_ck>;
 		reg = <0x423c>;
 		ti,max-div = <2>;
 	};
 
-	disp_clk: disp_clk@4244 {
+	disp_clk: clock-disp@4244 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "disp_clk";
 		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
 		reg = <0x4244>;
 		ti,set-rate-parent;
 	};
 
-	dpll_extdev_ck: dpll_extdev_ck@2e60 {
+	dpll_extdev_ck: clock@2e60 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_extdev_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
-		reg = <0x2e60>, <0x2e64>, <0x2e6c>;
+		reg = <0x2e60>, <0x2e64>, <0x2e6c>, <0x2e88>, <0x2e8c>;
 	};
 
-	dpll_extdev_m2_ck: dpll_extdev_m2_ck@2e70 {
+	dpll_extdev_m2_ck: clock-dpll-extdev-m2-8@2e70 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_extdev_m2_ck";
 		clocks = <&dpll_extdev_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -571,66 +650,75 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mux_synctimer32k_ck: mux_synctimer32k_ck@4230 {
+	mux_synctimer32k_ck: clock-mux-synctimer32k@4230 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "mux_synctimer32k_ck";
 		clocks = <&clk_32768_ck>, <&clk_32k_tpm_ck>, <&clkdiv32k_ick>;
 		reg = <0x4230>;
 	};
 
-	timer8_fck: timer8_fck@421c {
+	timer8_fck: clock-timer8-fck@421c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer8_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x421c>;
 	};
 
-	timer9_fck: timer9_fck@4220 {
+	timer9_fck: clock-timer9-fck@4220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer9_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x4220>;
 	};
 
-	timer10_fck: timer10_fck@4224 {
+	timer10_fck: clock-timer10-fck@4224 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer10_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x4224>;
 	};
 
-	timer11_fck: timer11_fck@4228 {
+	timer11_fck: clock-timer11-fck@4228 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer11_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x4228>;
 	};
 
-	cpsw_50m_clkdiv: cpsw_50m_clkdiv {
+	cpsw_50m_clkdiv: clock-cpsw-50m-clkdiv {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_50m_clkdiv";
 		clocks = <&dpll_core_m5_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	cpsw_5m_clkdiv: cpsw_5m_clkdiv {
+	cpsw_5m_clkdiv: clock-cpsw-5m-clkdiv {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_5m_clkdiv";
 		clocks = <&cpsw_50m_clkdiv>;
 		clock-mult = <1>;
 		clock-div = <10>;
 	};
 
-	dpll_ddr_x2_ck: dpll_ddr_x2_ck {
+	dpll_ddr_x2_ck: clock-dpll-ddr-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-x2-clock";
+		clock-output-names = "dpll_ddr_x2_ck";
 		clocks = <&dpll_ddr_ck>;
 	};
 
-	dpll_ddr_m4_ck: dpll_ddr_m4_ck@2db8 {
+	dpll_ddr_m4_ck: clock-dpll-ddr-m4-8@2db8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m4_ck";
 		clocks = <&dpll_ddr_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -639,9 +727,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_clkdcoldo: dpll_per_clkdcoldo@2e14 {
+	dpll_per_clkdcoldo: clock-dpll-per-clkdcoldo-8@2e14 {
 		#clock-cells = <0>;
 		compatible = "ti,fixed-factor-clock";
+		clock-output-names = "dpll_per_clkdcoldo";
 		clocks = <&dpll_per_ck>;
 		ti,clock-mult = <1>;
 		ti,clock-div = <1>;
@@ -650,177 +739,262 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dll_aging_clk_div: dll_aging_clk_div@4250 {
+	dll_aging_clk_div: clock-dll-aging-clk-div@4250 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dll_aging_clk_div";
 		clocks = <&sys_clkin_ck>;
 		reg = <0x4250>;
 		ti,dividers = <8>, <16>, <32>;
 	};
 
-	div_core_25m_ck: div_core_25m_ck {
+	div_core_25m_ck: clock-div-core-25m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "div_core_25m_ck";
 		clocks = <&sysclk_div>;
 		clock-mult = <1>;
 		clock-div = <8>;
 	};
 
-	func_12m_clk: func_12m_clk {
+	func_12m_clk: clock-func-12m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
 	};
 
-	vtp_clk_div: vtp_clk_div {
+	vtp_clk_div: clock-vtp-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "vtp_clk_div";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	usbphy_32khz_clkmux: usbphy_32khz_clkmux@4260 {
+	usbphy_32khz_clkmux: clock-usbphy-32khz-clkmux@4260 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "usbphy_32khz_clkmux";
 		clocks = <&clk_32768_ck>, <&clk_32k_tpm_ck>;
 		reg = <0x4260>;
 	};
 
-	usb_phy0_always_on_clk32k: usb_phy0_always_on_clk32k@2a40 {
+	usb_phy0_always_on_clk32k: clock-usb-phy0-always-on-clk32k-8@2a40 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy0_always_on_clk32k";
 		clocks = <&usbphy_32khz_clkmux>;
 		ti,bit-shift = <8>;
 		reg = <0x2a40>;
 	};
 
-	usb_phy1_always_on_clk32k: usb_phy1_always_on_clk32k@2a48 {
+	usb_phy1_always_on_clk32k: clock-usb-phy1-always-on-clk32k-8@2a48 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy1_always_on_clk32k";
 		clocks = <&usbphy_32khz_clkmux>;
 		ti,bit-shift = <8>;
 		reg = <0x2a48>;
 	};
+
+	clkout1_osc_div_ck: clock-clkout1-osc-div-ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clock-output-names = "clkout1_osc_div_ck";
+		clocks = <&sys_clkin_ck>;
+		ti,bit-shift = <20>;
+		ti,max-div = <4>;
+		reg = <0x4100>;
+	};
+
+	clkout1_src2_mux_ck: clock-clkout1-src2-mux-ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clock-output-names = "clkout1_src2_mux_ck";
+		clocks = <&clk_rc32k_ck>, <&sysclk_div>, <&dpll_ddr_m2_ck>,
+			 <&dpll_per_m2_ck>, <&dpll_disp_m2_ck>,
+			 <&dpll_mpu_m2_ck>;
+		reg = <0x4100>;
+	};
+
+	clkout1_src2_pre_div_ck: clock-clkout1-src2-pre-div-ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clock-output-names = "clkout1_src2_pre_div_ck";
+		clocks = <&clkout1_src2_mux_ck>;
+		ti,bit-shift = <4>;
+		ti,max-div = <8>;
+		reg = <0x4100>;
+	};
+
+	clkout1_src2_post_div_ck: clock-clkout1-src2-post-div-ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clock-output-names = "clkout1_src2_post_div_ck";
+		clocks = <&clkout1_src2_pre_div_ck>;
+		ti,bit-shift = <8>;
+		ti,max-div = <32>;
+		ti,index-power-of-two;
+		reg = <0x4100>;
+	};
+
+	clkout1_mux_ck: clock-clkout1-mux-ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clock-output-names = "clkout1_mux_ck";
+		clocks = <&clkout1_osc_div_ck>, <&clk_rc32k_ck>,
+			 <&clkout1_src2_post_div_ck>, <&dpll_extdev_m2_ck>;
+		ti,bit-shift = <16>;
+		reg = <0x4100>;
+	};
+
+	clkout1_ck: clock-clkout1-ck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clock-output-names = "clkout1_ck";
+		clocks = <&clkout1_mux_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x4100>;
+	};
 };
 
 &prcm {
-	wkup_cm: wkup-cm@2800 {
+	wkup_cm: clock@2800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkup_cm";
 		reg = <0x2800 0x400>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x2800 0x400>;
 
-		l3s_tsc_clkctrl: l3s-tsc-clkctrl@120 {
+		l3s_tsc_clkctrl: clock@120 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3s_tsc_clkctrl";
 			reg = <0x120 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l4_wkup_aon_clkctrl: l4-wkup-aon-clkctrl@228 {
+		l4_wkup_aon_clkctrl: clock@228 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_aon_clkctrl";
 			reg = <0x228 0xc>;
 			#clock-cells = <2>;
 		};
 
-		l4_wkup_clkctrl: l4-wkup-clkctrl@220 {
+		l4_wkup_clkctrl: clock@220 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_clkctrl";
 			reg = <0x220 0x4>, <0x328 0x44>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	mpu_cm: mpu-cm@8300 {
+	mpu_cm: clock@8300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x8300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8300 0x100>;
 
-		mpu_clkctrl: mpu-clkctrl@20 {
+		mpu_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	gfx_l3_cm: gfx-l3-cm@8400 {
+	gfx_l3_cm: clock@8400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gfx_l3_cm";
 		reg = <0x8400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8400 0x100>;
 
-		gfx_l3_clkctrl: gfx-l3-clkctrl@20 {
+		gfx_l3_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gfx_l3_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_rtc_cm: l4-rtc-cm@8500 {
+	l4_rtc_cm: clock@8500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_rtc_cm";
 		reg = <0x8500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8500 0x100>;
 
-		l4_rtc_clkctrl: l4-rtc-clkctrl@20 {
+		l4_rtc_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_rtc_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	per_cm: per-cm@8800 {
+	per_cm: clock@8800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "per_cm";
 		reg = <0x8800 0xc00>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8800 0xc00>;
 
-		l3_clkctrl: l3-clkctrl@20 {
+		l3_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_clkctrl";
 			reg = <0x20 0x3c>, <0x78 0x2c>;
 			#clock-cells = <2>;
 		};
 
-		l3s_clkctrl: l3s-clkctrl@68 {
+		l3s_clkctrl: clock@68 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3s_clkctrl";
 			reg = <0x68 0xc>, <0x220 0x4c>;
 			#clock-cells = <2>;
 		};
 
-		pruss_ocp_clkctrl: pruss-ocp-clkctrl@320 {
+		pruss_ocp_clkctrl: clock@320 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "pruss_ocp_clkctrl";
 			reg = <0x320 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l4ls_clkctrl: l4ls-clkctrl@420 {
+		l4ls_clkctrl: clock@420 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4ls_clkctrl";
 			reg = <0x420 0x1a4>;
 			#clock-cells = <2>;
 		};
 
-		emif_clkctrl: emif-clkctrl@720 {
+		emif_clkctrl: clock@720 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emif_clkctrl";
 			reg = <0x720 0x4>;
 			#clock-cells = <2>;
 		};
 
-		dss_clkctrl: dss-clkctrl@a20 {
+		dss_clkctrl: clock@a20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dss_clkctrl";
 			reg = <0xa20 0x4>;
 			#clock-cells = <2>;
 		};
 
-		cpsw_125mhz_clkctrl: cpsw-125mhz-clkctrl@b20 {
+		cpsw_125mhz_clkctrl: clock@b20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "cpsw_125mhz_clkctrl";
 			reg = <0xb20 0x4>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi b/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi
new file mode 100644
index 000000000000..46c5383f0eee
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi
@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Common PRUSS data for TI AM57xx platforms
+ */
+
+&ocp {
+	pruss1_tm: target-module@4b226000 {
+		compatible = "ti,sysc-pruss", "ti,sysc";
+		reg = <0x4b226000 0x4>,
+		      <0x4b226004 0x4>;
+		reg-names = "rev", "sysc";
+		ti,sysc-mask = <(SYSC_PRUSS_STANDBY_INIT |
+				 SYSC_PRUSS_SUB_MWAIT)>;
+		ti,sysc-midle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>;
+		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>;
+		/* Domains (P, C): coreaon_pwrdm, l4per2_clkdm */
+		clocks = <&l4per2_clkctrl DRA7_L4PER2_PRUSS1_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0x4b200000 0x80000>;
+
+		pruss1: pruss@0 {
+			compatible = "ti,am5728-pruss";
+			reg = <0x0 0x80000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pruss1_mem: memories@0 {
+				reg = <0x0 0x2000>,
+				      <0x2000 0x2000>,
+				      <0x10000 0x8000>;
+				reg-names = "dram0", "dram1",
+					    "shrdram2";
+			};
+
+			pruss1_cfg: cfg@26000 {
+				compatible = "ti,pruss-cfg", "syscon";
+				reg = <0x26000 0x2000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x26000 0x2000>;
+
+				clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pruss1_iepclk_mux: iepclk-mux@30 {
+						reg = <0x30>;
+						#clock-cells = <0>;
+						clocks = <&dpll_gmac_m3x2_ck>,  /* icss_iep_clk */
+							 <&dpll_gmac_h13x2_ck>; /* icss_clk */
+					};
+				};
+			};
+
+			pruss1_mii_rt: mii-rt@32000 {
+				compatible = "ti,pruss-mii", "syscon";
+				reg = <0x32000 0x58>;
+			};
+
+			pruss1_intc: interrupt-controller@20000 {
+				compatible = "ti,pruss-intc";
+				reg = <0x20000 0x2000>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+				interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "host_intr0", "host_intr1",
+						  "host_intr2", "host_intr3",
+						  "host_intr4", "host_intr5",
+						  "host_intr6", "host_intr7";
+			};
+
+			pru1_0: pru@34000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x34000 0x3000>,
+				      <0x22000 0x400>,
+				      <0x22400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru1_0-fw";
+			};
+
+			pru1_1: pru@38000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x38000 0x3000>,
+				      <0x24000 0x400>,
+				      <0x24400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru1_1-fw";
+			};
+
+			pruss1_mdio: mdio@32400 {
+				compatible = "ti,davinci_mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&dpll_gmac_h13x2_ck>;
+				clock-names = "fck";
+				bus_freq = <1000000>;
+				reg = <0x32400 0x90>;
+			};
+		};
+	};
+
+	pruss2_tm: target-module@4b2a6000 {
+		compatible = "ti,sysc-pruss", "ti,sysc";
+		reg = <0x4b2a6000 0x4>,
+		      <0x4b2a6004 0x4>;
+		reg-names = "rev", "sysc";
+		ti,sysc-mask = <(SYSC_PRUSS_STANDBY_INIT |
+				 SYSC_PRUSS_SUB_MWAIT)>;
+		ti,sysc-midle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>;
+		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>;
+		/* Domains (P, C): coreaon_pwrdm, l4per2_clkdm */
+		clocks = <&l4per2_clkctrl DRA7_L4PER2_PRUSS2_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0x4b280000 0x80000>;
+
+		pruss2: pruss@0 {
+			compatible = "ti,am5728-pruss";
+			reg = <0x0 0x80000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pruss2_mem: memories@0 {
+				reg = <0x0 0x2000>,
+				      <0x2000 0x2000>,
+				      <0x10000 0x8000>;
+				reg-names = "dram0", "dram1",
+					    "shrdram2";
+			};
+
+			pruss2_cfg: cfg@26000 {
+				compatible = "ti,pruss-cfg", "syscon";
+				reg = <0x26000 0x2000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x26000 0x2000>;
+
+				clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pruss2_iepclk_mux: iepclk-mux@30 {
+						reg = <0x30>;
+						#clock-cells = <0>;
+						clocks = <&dpll_gmac_m3x2_ck>,  /* icss_iep_clk */
+							 <&dpll_gmac_h13x2_ck>; /* icss_clk */
+					};
+				};
+			};
+
+			pruss2_mii_rt: mii-rt@32000 {
+				compatible = "ti,pruss-mii", "syscon";
+				reg = <0x32000 0x58>;
+			};
+
+			pruss2_intc: interrupt-controller@20000 {
+				compatible = "ti,pruss-intc";
+				reg = <0x20000 0x2000>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "host_intr0", "host_intr1",
+						  "host_intr2", "host_intr3",
+						  "host_intr4", "host_intr5",
+						  "host_intr6", "host_intr7";
+			};
+
+			pru2_0: pru@34000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x34000 0x3000>,
+				      <0x22000 0x400>,
+				      <0x22400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru2_0-fw";
+			};
+
+			pru2_1: pru@38000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x38000 0x3000>,
+				      <0x24000 0x400>,
+				      <0x24400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru2_1-fw";
+			};
+
+			pruss2_mdio: mdio@32400 {
+				compatible = "ti,davinci_mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&dpll_gmac_h13x2_ck>;
+				clock-names = "fck";
+				bus_freq = <1000000>;
+				reg = <0x32400 0x90>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/am5718.dtsi b/arch/arm/boot/dts/ti/omap/am5718.dtsi
index d51007c3e8c4..6d7530a48c73 100644
--- a/arch/arm/boot/dts/am5718.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am5718.dtsi
@@ -1,9 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "dra72x.dtsi"
+#include "am57-pruss.dtsi"
 
 / {
 	compatible = "ti,am5718", "ti,dra7";
@@ -16,17 +17,13 @@
  * VCP1, VCP2
  * MLB
  * ISS
- * USB3, USB4
+ * USB3
  */
 
 &usb3_tm {
 	status = "disabled";
 };
 
-&usb4_tm {
-	status = "disabled";
-};
-
 &atl_tm {
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/ti/omap/am571x-idk-touchscreen.dtso b/arch/arm/boot/dts/ti/omap/am571x-idk-touchscreen.dtso
new file mode 100644
index 000000000000..c051ee6c1130
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am571x-idk-touchscreen.dtso
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	touchscreen: edt-ft5506@38 {
+		compatible = "edt,edt-ft5506", "edt,edt-ft5x06";
+
+		reg = <0x38>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+
+		/* GPIO line is inverted before going to touch panel */
+		reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <1920>;
+		touchscreen-size-y = <1200>;
+
+		wakeup-source;
+	};
+};
diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/ti/omap/am571x-idk.dts
index 820ce3b60bb6..322cf79d22e9 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/ti/omap/am571x-idk.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -10,6 +10,7 @@
 #include "dra7-mmc-iodelay.dtsi"
 #include "dra72x-mmc-iodelay.dtsi"
 #include "am57xx-idk-common.dtsi"
+#include "dra7-ipu-dsp-common.dtsi"
 
 / {
 	model = "TI AM5718 IDK";
@@ -20,6 +21,33 @@
 		reg = <0x0 0x80000000 0x0 0x40000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		cpu0-led {
@@ -140,38 +168,32 @@
 };
 
 &extcon_usb2 {
-	id-gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
-	vbus-gpio = <&gpio7 22 GPIO_ACTIVE_HIGH>;
+	id-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+	vbus-gpios = <&gpio7 22 GPIO_ACTIVE_HIGH>;
 };
 
 &sn65hvs882 {
 	load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
 };
 
-&mailbox5 {
+&ipu2 {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
+	memory-region = <&ipu2_memory_region>;
 };
 
-&mailbox6 {
+&ipu1 {
 	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
+	memory-region = <&ipu1_memory_region>;
 };
 
-&pcie1_rc {
+&dsp1 {
 	status = "okay";
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+	memory-region = <&dsp1_memory_region>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+&pcie1_rc {
+	status = "okay";
+	gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
 };
 
 &mmc1 {
@@ -187,29 +209,10 @@
 	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
 };
 
-&mac_sw {
-	pinctrl-names = "default", "sleep";
-	status = "okay";
-};
-
-&cpsw_port1 {
-	phy-handle = <&ethphy0_sw>;
-	phy-mode = "rgmii";
-	ti,dual-emac-pvid = <1>;
+&pruss1_mdio {
+	status = "disabled";
 };
 
-&cpsw_port2 {
-	phy-handle = <&ethphy1_sw>;
-	phy-mode = "rgmii";
-	ti,dual-emac-pvid = <2>;
-};
-
-&davinci_mdio_sw {
-	ethphy0_sw: ethernet-phy@0 {
-		reg = <0>;
-	};
-
-	ethphy1_sw: ethernet-phy@1 {
-		reg = <1>;
-	};
+&pruss2_mdio {
+	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am5728.dtsi b/arch/arm/boot/dts/ti/omap/am5728.dtsi
index 82e5427ef6a9..5e0bdf16d485 100644
--- a/arch/arm/boot/dts/am5728.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am5728.dtsi
@@ -1,9 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "dra74x.dtsi"
+#include "am57-pruss.dtsi"
 
 / {
 	compatible = "ti,am5728", "ti,dra7";
diff --git a/arch/arm/boot/dts/ti/omap/am5729-beagleboneai.dts b/arch/arm/boot/dts/ti/omap/am5729-beagleboneai.dts
new file mode 100644
index 000000000000..c8e55642f9c6
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am5729-beagleboneai.dts
@@ -0,0 +1,698 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2014-2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "dra74x.dtsi"
+#include "am57xx-commercial-grade.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
+#include "dra74-ipu-dsp-common.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/dra.h>
+
+/ {
+	model = "BeagleBoard.org BeagleBone AI";
+	compatible = "beagle,am5729-beagleboneai", "ti,am5728",
+		     "ti,dra742", "ti,dra74", "ti,dra7";
+
+	aliases {
+		rtc0 = &tps659038_rtc;
+		rtc1 = &rtc;
+		display0 = &hdmi_conn;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp2_memory_region: dsp2-memory@9f000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9f000000 0x0 0x800000>;
+			reusable;
+			status = "okay";
+		};
+
+	};
+
+	vdd_adc: gpioregulator-vdd_adc {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd_adc";
+		vin-supply = <&vdd_5v>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0
+			3300000 1>;
+	};
+
+	vdd_5v: fixedregulator-vdd_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vtt_fixed: fixedregulator-vtt {
+		/* TPS51200 */
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_fixed";
+		vin-supply = <&vdd_ddr>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			label = "beaglebone:green:usr0";
+			gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led1 {
+			label = "beaglebone:green:usr1";
+			gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "beaglebone:green:usr2";
+			gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "beaglebone:green:usr3";
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "beaglebone:green:usr4";
+			gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "netdev";
+			default-state = "off";
+		};
+	};
+
+	hdmi_conn: connector@0 {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_encoder_out>;
+			};
+		};
+	};
+
+	hdmi_enc: encoder@0 {
+		/* "ti,tpd12s016" software compatible with "ti,tpd12s015"
+		 *  no need for individual driver
+		 */
+		compatible = "ti,tpd12s015";
+		gpios = <0>,
+			<0>,
+			<&gpio7 12 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+
+			port@0 {
+				reg = <0x0>;
+
+				hdmi_encoder_in: endpoint@0 {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <0x1>;
+
+				hdmi_encoder_out: endpoint@0 {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	emmc_pwrseq: emmc_pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+	};
+
+	brcmf_pwrseq: brcmf_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>,	/* BT-REG-ON */
+				<&gpio3 18 GPIO_ACTIVE_LOW>;	/* WL-REG-ON */
+	};
+
+	extcon_usb1: extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		ti,enable-id-detection;
+		id-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps659038: tps659038@58 {
+		compatible = "ti,tps659038";
+		reg = <0x58>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+
+		#interrupt-cells = <2>;
+		interrupt-controller;
+
+		ti,system-power-controller;
+		ti,palmas-override-powerhold;
+
+		tps659038_pmic {
+			compatible = "ti,tps659038-pmic";
+
+			smps12-in-supply = <&vdd_5v>;
+			smps3-in-supply = <&vdd_5v>;
+			smps45-in-supply = <&vdd_5v>;
+			smps6-in-supply = <&vdd_5v>;
+			smps7-in-supply = <&vdd_5v>;
+			mps3-in-supply = <&vdd_5v>;
+			smps8-in-supply = <&vdd_5v>;
+			smps9-in-supply = <&vdd_5v>;
+			ldo1-in-supply = <&vdd_5v>;
+			ldo2-in-supply = <&vdd_5v>;
+			ldo3-in-supply = <&vdd_5v>;
+			ldo4-in-supply = <&vdd_5v>;
+			ldo9-in-supply = <&vdd_5v>;
+			ldoln-in-supply = <&vdd_5v>;
+			ldousb-in-supply = <&vdd_5v>;
+			ldortc-in-supply = <&vdd_5v>;
+
+			regulators {
+				vdd_mpu: smps12 {
+					/* VDD_MPU */
+					regulator-name = "smps12";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_ddr: smps3 {
+					/* VDD_DDR EMIF1 EMIF2 */
+					regulator-name = "smps3";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_dspeve: smps45 {
+					/* VDD_DSPEVE on AM572 */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_gpu: smps6 {
+					/* VDD_GPU */
+					regulator-name = "smps6";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_core: smps7 {
+					/* VDD_CORE */
+					regulator-name = "smps7";
+					regulator-min-microvolt = < 850000>;	/*** 1.15V */
+					regulator-max-microvolt = <1150000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_iva: smps8 {
+					/* VDD_IVAHD */				/*** 1.06V */
+					regulator-name = "smps8";
+				};
+
+				vdd_3v3: smps9 {
+					/* VDD_3V3 */
+					regulator-name = "smps9";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_sd: ldo1 {
+					/* VDDSHV8 - VSDMMC  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				vdd_1v8: ldo2 {
+					/* VDDSH18V */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_1v8_phy_ldo3: ldo3 {
+					/* R1.3a 572x V1_8PHY_LDO3: USB, SATA */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_1v8_phy_ldo4: ldo4 {
+					/* R1.3a 572x V1_8PHY_LDO4: PCIE, HDMI*/
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* LDO5-8 unused */
+
+				vdd_rtc: ldo9 {
+					/* VDD_RTC  */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = < 840000>;
+					regulator-max-microvolt = <1160000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_1v8_pll: ldoln {
+					/* VDDA_1V8_PLL */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldortc_reg: ldortc {
+					/* VDDA_RTC  */
+					regulator-name = "ldortc";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				regen1: regen1 {
+					/* VDD_3V3_ON */
+					regulator-name = "regen1";
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				regen2: regen2 {
+					/* Needed for PMIC internal resource */
+					regulator-name = "regen2";
+					regulator-boot-on;
+					regulator-always-on;
+				};
+			};
+		};
+
+		tps659038_rtc: tps659038_rtc {
+			compatible = "ti,palmas-rtc";
+			interrupt-parent = <&tps659038>;
+			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		tps659038_pwr_button: tps659038_pwr_button {
+			compatible = "ti,palmas-pwrbutton";
+			interrupt-parent = <&tps659038>;
+			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+			ti,palmas-long-press-seconds = <12>;
+		};
+
+		tps659038_gpio: tps659038_gpio {
+			compatible = "ti,palmas-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+
+	/* STMPE811 touch screen controller */
+	stmpe811@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio2>;
+		interrupt-controller;
+		id = <0>;
+		blocks = <0x5>;
+		irq-trigger = <0x1>;
+		st,mod-12b = <1>; /* 12-bit ADC */
+		st,ref-sel = <0>; /* internal ADC reference */
+		st,adc-freq = <1>; /* 3.25 MHz ADC clock speed */
+		st,sample-time = <4>; /* ADC converstion time: 80 clocks */
+
+		stmpe_adc {
+			compatible = "st,stmpe-adc";
+			st,norequest-mask = <0x00>; /* mask any channels to be used by touchscreen */
+			adc0: iio-device@0 {
+				#io-channel-cells = <1>;
+				iio-channels = <&adc0 4>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>, <&adc0 5>, <&adc0 6>;
+				iio-channel-names = "AIN0_P9_39", "AIN1_P9_40", "AIN2_P9_37", "AIN3_P9_38",
+					"AIN4_P9_33", "AIN5_P9_36", "AIN6_P9_35";
+			};
+		};
+
+		stmpe_touchscreen {
+			status = "disabled";
+			compatible = "st,stmpe-ts";
+			/* 8 sample average control */
+			st,ave-ctrl = <3>;
+			/* 7 length fractional part in z */
+			st,fraction-z = <7>;
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			/* 1 ms panel driver settling time */
+			st,settling = <3>;
+			/* 5 ms touch detect interrupt delay */
+			st,touch-det-delay = <5>;
+		};
+
+		stmpe_gpio {
+			compatible = "st,stmpe-gpio";
+		};
+
+		stmpe_pwm {
+			compatible = "st,stmpe-pwm";
+			#pwm-cells = <2>;
+		};
+	};
+};
+
+&mcspi3 {
+	status = "okay";
+	ti,pindir-d0-out-d1-in;
+
+	sn65hvs882: sn65hvs882@0 {
+		compatible = "pisosr-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cpol;
+	};
+};
+
+&cpu0 {
+	vdd-supply = <&vdd_mpu>;
+	voltage-tolerance = <1>;
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&davinci_mdio_sw {
+	reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <2>;
+
+	phy0: ethernet-phy@4 {
+		reg = <4>;
+		eee-broken-100tx;
+		eee-broken-1000t;
+	};
+};
+
+&mac_sw {
+	status = "okay";
+};
+
+&cpsw_port1 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&ocp {
+	pruss1_shmem: pruss_shmem@4b200000 {
+		status = "okay";
+		compatible = "ti,pruss-shmem";
+		reg = <0x4b200000 0x020000>;
+	};
+
+	pruss2_shmem: pruss_shmem@4b280000 {
+		status = "okay";
+		compatible = "ti,pruss-shmem";
+		reg = <0x4b280000 0x020000>;
+	};
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vdd_sd>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
+};
+
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&vdd_1v8>;
+	vqmmc-supply = <&vdd_1v8>;
+	bus-width = <8>;
+	ti,non-removable;
+	non-removable;
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	ti,needs-special-reset;
+	dmas = <&sdma_xbar 47>, <&sdma_xbar 48>;
+	dma-names = "tx", "rx";
+
+};
+
+&mmc4 {
+	/* DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3 V signaling). */
+	/* HS: High speed up to 50 MHz (3.3 V signaling). */
+	/* SDR12: SDR up to 25 MHz (1.8 V signaling). */
+	/* SDR25: SDR up to 50 MHz (1.8 V signaling). */
+	/* SDR50: SDR up to 100 MHz (1.8 V signaling). */
+	/* SDR104: SDR up to 208 MHz (1.8 V signaling) */
+	/* DDR50: DDR up to 50 MHz (1.8 V signaling). */
+	status = "okay";
+
+	ti,needs-special-reset;
+	vmmc-supply = <&vdd_3v3>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	bus-width = <4>;
+	ti,non-removable;
+	non-removable;
+	no-1-8-v;
+	max-frequency = <24000000>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	mmc-pwrseq = <&brcmf_pwrseq>;
+
+	brcmf: wifi@1 {
+		status = "okay";
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+
+		brcm,sd-head-align = <4>;
+		brcm,sd_head_align = <4>;
+		brcm,sd_sgentry_align = <512>;
+
+		interrupt-parent = <&gpio3>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&usb2_phy1 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&usb2_phy2 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&usb2 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&dss {
+	status = "okay";
+	vdda_video-supply = <&vdd_1v8_pll>;
+};
+
+&hdmi {
+	status = "okay";
+	vdda-supply = <&vdd_1v8_phy_ldo4>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&hdmi_encoder_in>;
+		};
+	};
+};
+
+&bandgap {
+	status = "okay";
+};
+
+&cpu_alert0 {
+	temperature = <55000>; /* milliCelsius */
+};
+
+&cpu_crit {
+	temperature = <85000>; /* milliCelsius */
+};
+
+&gpu_crit {
+	temperature = <85000>; /* milliCelsius */
+};
+
+&core_crit {
+	temperature = <85000>; /* milliCelsius */
+};
+
+&dspeve_crit {
+	temperature = <85000>; /* milliCelsius */
+};
+
+&iva_crit {
+	temperature = <85000>; /* milliCelsius */
+};
+
+&sata {
+	status = "disabled";
+};
+
+&sata_phy {
+	status = "disabled";
+};
+
+/* bluetooth */
+&uart6 {
+	status = "okay";
+};
+
+/* cape header stuff */
+&i2c4 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_memory_region>;
+};
+
+&ipu1 {
+	status = "okay";
+	memory-region = <&ipu1_memory_region>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_memory_region>;
+};
+
+&dsp2 {
+	status = "okay";
+	memory-region = <&dsp2_memory_region>;
+};
diff --git a/arch/arm/boot/dts/am572x-idk-common.dtsi b/arch/arm/boot/dts/ti/omap/am572x-idk-common.dtsi
index a064f13b3880..3fca84819dc0 100644
--- a/arch/arm/boot/dts/am572x-idk-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am572x-idk-common.dtsi
@@ -1,11 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "am57xx-idk-common.dtsi"
+#include "dra74-ipu-dsp-common.dtsi"
 
 / {
 	memory@0 {
@@ -13,6 +14,40 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp2_memory_region: dsp2-memory@9f000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9f000000 0x0 0x800000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	status-leds {
 		compatible = "gpio-leds";
 		cpu0-led {
@@ -134,8 +169,8 @@
 };
 
 &extcon_usb2 {
-	id-gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
-	vbus-gpio = <&gpio3 26 GPIO_ACTIVE_HIGH>;
+	id-gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+	vbus-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>;
 };
 
 &sn65hvs882 {
@@ -147,26 +182,22 @@
 	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 };
 
-&pcie1_ep {
-	gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_memory_region>;
 };
 
-&mailbox5 {
+&ipu1 {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
+	memory-region = <&ipu1_memory_region>;
 };
 
-&mailbox6 {
+&dsp1 {
 	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		status = "okay";
-	};
+	memory-region = <&dsp1_memory_region>;
+};
+
+&dsp2 {
+	status = "okay";
+	memory-region = <&dsp2_memory_region>;
 };
diff --git a/arch/arm/boot/dts/ti/omap/am572x-idk-touchscreen.dtso b/arch/arm/boot/dts/ti/omap/am572x-idk-touchscreen.dtso
new file mode 100644
index 000000000000..573e932b1239
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am572x-idk-touchscreen.dtso
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	touchscreen: edt-ft5506@38 {
+		compatible = "edt,edt-ft5506", "edt,edt-ft5x06";
+
+		reg = <0x38>;
+
+		interrupt-parent = <&gpio3>;
+		interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+
+		/* GPIO line is inverted before going to touch panel */
+		reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <1920>;
+		touchscreen-size-y = <1200>;
+
+		wakeup-source;
+	};
+};
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/ti/omap/am572x-idk.dts
index c3d966904d64..94a738cb0a4d 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/ti/omap/am572x-idk.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /dts-v1/;
@@ -28,7 +28,10 @@
 	pinctrl-2 = <&mmc2_pins_ddr_rev20>;
 };
 
-&mac {
-	status = "okay";
-	dual_emac;
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am5748.dtsi b/arch/arm/boot/dts/ti/omap/am5748.dtsi
index 5e129759d04a..a1f029e9d1f3 100644
--- a/arch/arm/boot/dts/am5748.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am5748.dtsi
@@ -1,9 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
  */
 
-#include "dra76x.dtsi"
+#include "dra74x-p.dtsi"
+#include "am57-pruss.dtsi"
 
 / {
 	compatible = "ti,am5748", "ti,dra762", "ti,dra7";
diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/ti/omap/am574x-idk.dts
index fa0088025b2c..47b9174d2353 100644
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/ti/omap/am574x-idk.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 
@@ -18,7 +18,7 @@
 
 &qspi {
 	spi-max-frequency = <96000000>;
-	m25p80@0 {
+	flash@0 {
 		spi-max-frequency = <96000000>;
 	};
 };
@@ -36,7 +36,14 @@
 	pinctrl-2 = <&mmc2_pins_default>;
 };
 
-&mac {
+&emif1 {
 	status = "okay";
-	dual_emac;
+};
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15-common.dtsi
index bc76f1705c0f..994e69ab38d7 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15-common.dtsi
@@ -1,12 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
 #include "am5728.dtsi"
 #include "am57xx-commercial-grade.dtsi"
 #include "dra74x-mmc-iodelay.dtsi"
+#include "dra74-ipu-dsp-common.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
@@ -29,6 +30,61 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	main_12v0: fixedregulator-main_12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "main_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	evm_5v0: fixedregulator-evm_5v0 {
+		/* Output of TPS54531D */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp2_memory_region: dsp2-memory@9f000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9f000000 0x0 0x800000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	vdd_3v3: fixedregulator-vdd_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
@@ -395,7 +451,7 @@
 			      <&dra7_pmx_core 0x3f8>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@1 {
 		reg = <1>;
 	};
@@ -405,21 +461,20 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
-	dual_emac;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&phy0>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <2>;
 };
 
 &mmc1 {
@@ -526,13 +581,13 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	vdda_video-supply = <&ldoln_reg>;
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 	vdda-supply = <&ldo4_reg>;
 
 	port {
@@ -543,11 +598,7 @@
 };
 
 &pcie1_rc {
-	status = "ok";
-	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
-};
-
-&pcie1_ep {
+	status = "okay";
 	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
 };
 
@@ -567,22 +618,30 @@
 	rx-num-evt = <32>;
 };
 
-&mailbox5 {
+&ipu2 {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
+	memory-region = <&ipu2_memory_region>;
 };
 
-&mailbox6 {
+&ipu1 {
 	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		status = "okay";
-	};
+	memory-region = <&ipu1_memory_region>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_memory_region>;
+};
+
+&dsp2 {
+	status = "okay";
+	memory-region = <&dsp2_memory_region>;
+};
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15-revb1.dts
index 39d1c4ff5749..83e174e053c7 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
+++ b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15-revb1.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "am57xx-beagle-x15-common.dtsi"
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15-revc.dts
index 4187a9729f96..656dd84460d2 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts
+++ b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15-revc.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014-2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "am57xx-beagle-x15-common.dtsi"
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15.dts
index a5c24ed4d12f..0a8b16505ed9 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/ti/omap/am57xx-beagle-x15.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "am57xx-beagle-x15-common.dtsi"
diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/ti/omap/am57xx-cl-som-am57x.dts
index 34ca761aeded..4fd831ff206f 100644
--- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
+++ b/arch/arm/boot/dts/ti/omap/am57xx-cl-som-am57x.dts
@@ -77,40 +77,40 @@
 };
 
 &dra7_pmx_core {
-	leds_pins_default: leds_pins_default {
+	leds_pins_default: leds-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x347c, PIN_OUTPUT | MUX_MODE14)	/* gpmc_a15.gpio2_5 */
 		>;
 	};
 
-	i2c1_pins_default: i2c1_pins_default {
+	i2c1_pins_default: i2c1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda.sda */
 			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl.scl */
 		>;
 	};
 
-	i2c3_pins_default: i2c3_pins_default {
+	i2c3_pins_default: i2c3-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10)	/* mcasp1_aclkx.i2c3_sda */
 			DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10)	/* mcasp1_fsx.i2c3_scl */
 		>;
 	};
 
-	i2c4_pins_default: i2c4_pins_default {
+	i2c4_pins_default: i2c4-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x36ac, PIN_INPUT| MUX_MODE10)	/* mcasp1_acl.i2c4_sda */
 			DRA7XX_CORE_IOPAD(0x36b0, PIN_INPUT| MUX_MODE10)	/* mcasp1_fsr.i2c4_scl */
 		>;
 	};
 
-	tps659038_pins_default: tps659038_pins_default {
+	tps659038_pins_default: tps659038-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
 		>;
 	};
 
-	mmc2_pins_default: mmc2_pins_default {
+	mmc2_pins_default: mmc2-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -125,7 +125,7 @@
 		>;
 	};
 
-	qspi1_pins: pinmux_qspi1_pins {
+	qspi1_pins: qspi1-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3474, PIN_INPUT | MUX_MODE1)	/* gpmc_a13.qspi1_rtclk */
 			DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1)	/* gpmc_a16.qspi1_d0 */
@@ -136,7 +136,7 @@
 		>;
 	};
 
-	cpsw_pins_default: cpsw_pins_default {
+	cpsw_pins_default: cpsw-default-pins {
 		pinctrl-single,pins = <
 			/* Slave at addr 0x0 */
 			DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_tclk */
@@ -168,7 +168,7 @@
 		>;
 	};
 
-	cpsw_pins_sleep: cpsw_pins_sleep {
+	cpsw_pins_sleep: cpsw-sleep-pins {
 		pinctrl-single,pins = <
 			/* Slave 1 */
 			DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
@@ -200,7 +200,7 @@
 		>;
 	};
 
-	davinci_mdio_pins_default: davinci_mdio_pins_default {
+	davinci_mdio_pins_default: davinci-mdio-default-pins {
 		pinctrl-single,pins = <
 			/* MDIO */
 			DRA7XX_CORE_IOPAD(0x3590, PIN_OUTPUT_PULLUP | MUX_MODE3)/* vin2a_d10.mdio_mclk */
@@ -208,20 +208,20 @@
 		>;
 	};
 
-	davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
+	davinci_mdio_pins_sleep: davinci-mdio-sleep-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3590, PIN_INPUT | MUX_MODE15)
 			DRA7XX_CORE_IOPAD(0x3594, PIN_INPUT | MUX_MODE15)
 		>;
 	};
 
-	ads7846_pins: pinmux_ads7846_pins {
+	ads7846_pins: ads7846-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3464, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpmc_a9.gpio1_31 */
 		>;
 	};
 
-	mcasp3_pins_default: mcasp3_pins_default {
+	mcasp3_pins_default: mcasp3-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
 			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
@@ -230,7 +230,7 @@
 		>;
 	};
 
-	mcasp3_pins_sleep: mcasp3_pins_sleep {
+	mcasp3_pins_sleep: mcasp3-sleep-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
 			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
@@ -454,20 +454,20 @@
 
 &mailbox5 {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
 		status = "okay";
 	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
 		status = "okay";
 	};
 };
 
 &mailbox6 {
 	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
 		status = "okay";
 	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
+	mbox_dsp2_ipc3x: mbox-dsp2-ipc3x {
 		status = "okay";
 	};
 };
@@ -491,7 +491,7 @@
 
 	spi-max-frequency = <48000000>;
 
-	spi_flash: spi_flash@0 {
+	spi_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "spansion,m25p80", "jedec,spi-nor";
@@ -527,7 +527,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <31 0>;
-		pendown-gpio = <&gpio1 31 0>;
+		pendown-gpio = <&gpio1 31 GPIO_ACTIVE_LOW>;
 
 
 		ti,x-min = /bits/ 16 <0x0>;
@@ -546,27 +546,26 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_pins_default>;
 	pinctrl-1 = <&cpsw_pins_sleep>;
-	dual_emac;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
-	dual_emac_res_vlan = <0>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii-txid";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_pins_default>;
 	pinctrl-1 = <&davinci_mdio_pins_sleep>;
@@ -611,12 +610,19 @@
 	>;
 };
 
-&gpio3 {
-	status = "okay";
+&gpio3_target {
 	ti,no-reset-on-init;
 };
 
-&gpio2 {
+&gpio2_target {
 	status = "okay";
 	ti,no-reset-on-init;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/am57xx-commercial-grade.dtsi b/arch/arm/boot/dts/ti/omap/am57xx-commercial-grade.dtsi
index 3eed6e09c884..3eed6e09c884 100644
--- a/arch/arm/boot/dts/am57xx-commercial-grade.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am57xx-commercial-grade.dtsi
diff --git a/arch/arm/boot/dts/ti/omap/am57xx-evm.dtso b/arch/arm/boot/dts/ti/omap/am57xx-evm.dtso
new file mode 100644
index 000000000000..12385a31061e
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am57xx-evm.dtso
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DT overlay for AM57xx GP EVM boards
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+&{/} {
+	compatible = "ti,am5728-evm", "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
+	model = "TI AM5728 EVM";
+
+	aliases {
+		display0 = "/display";
+		display1 = "/connector"; // Fixme: &lcd0 and &hdmi0 could be
+					 // resolved here correcly based on
+					 // information in the base dtb symbol
+					 // table with a fix in dtc
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-user1 {
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			label = "USER1";
+			linux,code = <BTN_1>;
+		};
+
+		button-user2 {
+			gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+			label = "USER2";
+			linux,code = <BTN_2>;
+		};
+
+		button-user3 {
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+			label = "USER3";
+			linux,code = <BTN_3>;
+		};
+
+		button-user4 {
+			gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+			label = "USER4";
+			linux,code = <BTN_4>;
+		};
+
+		button-user5 {
+			gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+			label = "USER5";
+			linux,code = <BTN_5>;
+		};
+	};
+
+	lcd0: display {
+		compatible = "osddisplays,osd070t1718-19ts", "panel-dpi";
+		backlight = <&lcd_bl>;
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		label = "lcd";
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+	};
+
+	lcd_bl: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 243 245 247 249 251 252 253 255>;
+		default-brightness-level = <8>;
+		pwms = <&ehrpwm1 0 50000 0>;
+	};
+};
+
+&ehrpwm1 {
+	status = "okay";
+};
+
+&epwmss1 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	touchscreen@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		attb-gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x5c>;
+		reset-gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <1024>;
+		touchscreen-size-y = <600>;
+	};
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&dss {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			dpi_out: endpoint {
+				data-lines = <24>;
+				remote-endpoint = <&lcd_in>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/ti/omap/am57xx-idk-common.dtsi
index 398721c7201c..43e3623f079c 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am57xx-idk-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "am57xx-industrial-grade.dtsi"
@@ -9,6 +9,7 @@
 	aliases {
 		rtc0 = &tps659038_rtc;
 		rtc1 = &rtc;
+		display0 = &hdmi0;
 	};
 
 	chosen {
@@ -34,6 +35,16 @@
 		regulator-boot-on;
 	};
 
+	v1_2d: fixedregulator-v1_2d {
+		compatible = "regulator-fixed";
+		regulator-name = "V1_2D";
+		vin-supply = <&vmain>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vtt_fixed: fixedregulator-vtt {
 		/* TPS51200 */
 		compatible = "regulator-fixed";
@@ -96,17 +107,65 @@
 			default-state = "off";
 		};
 	};
+
+	hdmi0: connector@0 {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
+
+	tpd12s015: encoder@0 {
+		compatible = "ti,tpd12s016", "ti,tpd12s015";
+
+		gpios = <0>, /* optional CT_CP_HPD */
+			<0>, /* optional LS_OE */
+			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint@0 {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint@0 {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	src_clk_x1: src_clk_x1 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <20000000>;
+	};
 };
 
 &dra7_pmx_core {
-	dcan1_pins_default: dcan1_pins_default {
+	dcan1_pins_default: dcan1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* dcan1_tx */
 			DRA7XX_CORE_IOPAD(0x37d4, PIN_INPUT_PULLUP | MUX_MODE0)		/* dcan1_rx */
 		>;
 	};
 
-	dcan1_pins_sleep: dcan1_pins_sleep {
+	dcan1_pins_sleep: dcan1-sleep-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
 			DRA7XX_CORE_IOPAD(0x37d4, MUX_MODE15 | PULL_UP)	/* dcan1_rx.off */
@@ -335,6 +394,32 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
+
+	dsi_bridge: tc358778@e {
+		compatible = "toshiba,tc358778", "toshiba,tc358768";
+		reg = <0xe>;
+		status = "disabled";
+
+		clocks = <&src_clk_x1>;
+		clock-names = "refclk";
+
+		vddc-supply = <&v1_2d>;
+		vddmipi-supply = <&v1_2d>;
+		vddio-supply = <&v3_3d>;
+
+		dsi_bridge_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				rgb_in: endpoint {
+					remote-endpoint = <&dpi_out>;
+					data-lines = <24>;
+				};
+			};
+		};
+	};
 };
 
 &mcspi3 {
@@ -363,19 +448,23 @@
 	ext-clk-src;
 };
 
-&cpsw_emac0 {
+&mac_sw {
+	status = "okay";
+};
+
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+	phy-mode = "rgmii-rxid";
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
@@ -437,7 +526,7 @@
 	status = "okay";
 
 	spi-max-frequency = <76800000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "s25fl256s1", "jedec,spi-nor";
 		spi-max-frequency = <76800000>;
 		reg = <0>;
@@ -453,7 +542,7 @@
 		 */
 		partition@0 {
 			label = "QSPI.SPL";
-			reg = <0x00000000 0x000040000>;
+			reg = <0x00000000 0x00040000>;
 		};
 		partition@1 {
 			label = "QSPI.u-boot";
@@ -485,3 +574,35 @@
 &cpu0 {
 	vdd-supply = <&smps12_reg>;
 };
+
+&hdmi {
+	status = "okay";
+
+	vdda-supply = <&ldo4_reg>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};
+
+&dss {
+	status = "okay";
+
+	vdda_video-supply = <&ldoln_reg>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			dpi_out: endpoint {
+				remote-endpoint = <&rgb_in>;
+				data-lines = <24>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/am57xx-idk-lcd-osd101t2045.dtso b/arch/arm/boot/dts/ti/omap/am57xx-idk-lcd-osd101t2045.dtso
new file mode 100644
index 000000000000..25d74e9f3c9e
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am57xx-idk-lcd-osd101t2045.dtso
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	aliases {
+		display0 = "/display";
+		display1 = "/connector";
+	};
+
+	lcd_bl: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 1>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+};
+
+&dsi_bridge {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	lcd: display {
+		compatible = "osddisplays,osd101t2045-53ts";
+		reg = <0>;
+
+		label = "lcd";
+
+		backlight = <&lcd_bl>;
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&dsi_bridge_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@1 {
+		reg = <1>;
+		dsi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/ti/omap/am57xx-idk-lcd-osd101t2587.dtso b/arch/arm/boot/dts/ti/omap/am57xx-idk-lcd-osd101t2587.dtso
new file mode 100644
index 000000000000..8cea7ba32487
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/am57xx-idk-lcd-osd101t2587.dtso
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	aliases {
+		display0 = "/display";
+		display1 = "/connector";
+	};
+
+	lcd_bl: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 1>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+};
+
+&dsi_bridge {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	lcd: display {
+		compatible = "osddisplays,osd101t2587-53ts";
+		reg = <0>;
+
+		label = "lcd";
+
+		backlight = <&lcd_bl>;
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&dsi_bridge_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@1 {
+		reg = <1>;
+		dsi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/am57xx-industrial-grade.dtsi b/arch/arm/boot/dts/ti/omap/am57xx-industrial-grade.dtsi
index 422f953fc8d8..422f953fc8d8 100644
--- a/arch/arm/boot/dts/am57xx-industrial-grade.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am57xx-industrial-grade.dtsi
diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/ti/omap/am57xx-sbc-am57x.dts
index ce5bf1d92eab..363115afb0a4 100644
--- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts
+++ b/arch/arm/boot/dts/ti/omap/am57xx-sbc-am57x.dts
@@ -20,14 +20,14 @@
 };
 
 &dra7_pmx_core {
-	uart3_pins_default: uart3_pins_default {
+	uart3_pins_default: uart3-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0)	/* uart3_rxd */
 			DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0)	/* uart3_txd */
 		>;
 	};
 
-	mmc1_pins_default: mmc1_pins_default {
+	mmc1_pins_default: mmc1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -40,33 +40,33 @@
 		>;
 	};
 
-	usb1_pins: pinmux_usb1_pins {
+	usb1_pins: usb1-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
 		>;
 	};
 
-	i2c5_pins_default: i2c5_pins_default {
+	i2c5_pins_default: i2c5-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT| MUX_MODE10)	/* mcasp1_axr0.i2c5_sda */
 			DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT| MUX_MODE10)	/* mcasp1_axr1.i2c5_scl */
 		>;
 	};
 
-	lcd_pins_default: lcd_pins_default {
+	lcd_pins_default: lcd-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3564, PIN_OUTPUT | MUX_MODE14)      /* vin2a_vsync0.gpio4_0 */
 		>;
 	};
 
-	hdmi_pins: pinmux_hdmi_pins {
+	hdmi_pins: hdmi-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1)	/* i2c2_sda.hdmi1_ddc_scl */
 			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1)	/* i2c2_scl.hdmi1_ddc_sda */
 		>;
 	};
 
-	hdmi_conn_pins: pinmux_hdmi_conn_pins {
+	hdmi_conn_pins: hdmi-conn-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT | MUX_MODE14)	/* spi1_cs2.gpio7_12 */
 		>;
@@ -120,7 +120,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	vdda_video-supply = <&ldoln_reg>;
 
@@ -148,7 +148,7 @@
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 	vdda-supply = <&ldo4_reg>;
 
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/compulab-sb-som.dtsi b/arch/arm/boot/dts/ti/omap/compulab-sb-som.dtsi
index f5e6216718d8..f5e6216718d8 100644
--- a/arch/arm/boot/dts/compulab-sb-som.dtsi
+++ b/arch/arm/boot/dts/ti/omap/compulab-sb-som.dtsi
diff --git a/arch/arm/boot/dts/ti/omap/dm3725.dtsi b/arch/arm/boot/dts/ti/omap/dm3725.dtsi
new file mode 100644
index 000000000000..d24e906a14b1
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dm3725.dtsi
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2020 André Hentschel <nerv@dawncrow.de>
+ */
+
+#include "omap36xx.dtsi"
+
+&sgx_module {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/ti/omap/dm8148-evm.dts
index 3931fb068ff0..ae8d9fa09d16 100644
--- a/arch/arm/boot/dts/dm8148-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dm8148-evm.dts
@@ -24,12 +24,12 @@
 
 &cpsw_emac0 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 };
 
 &cpsw_emac1 {
 	phy-handle = <&ethphy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 };
 
 &davinci_mdio {
@@ -51,7 +51,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
-		linux,mtd-name= "micron,mt29f2g16aadwp";
+		linux,mtd-name = "micron,mt29f2g16aadwp";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "bch8";
@@ -80,19 +80,19 @@
 			label = "X-Loader";
 			reg = <0 0x80000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "U-Boot";
 			reg = <0x80000 0x1c0000>;
 		};
-		partition@0x1c0000 {
+		partition@1c0000 {
 			label = "Environment";
 			reg = <0x240000 0x40000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "Kernel";
 			reg = <0x280000 0x500000>;
 		};
-		partition@0x780000 {
+		partition@780000 {
 			label = "Filesystem";
 			reg = <0x780000 0xf880000>;
 		};
@@ -116,7 +116,7 @@
 };
 
 &pincntl {
-	sd1_pins: pinmux_sd1_pins {
+	sd1_pins: sd1-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0800, PIN_INPUT | 0x1)	/* SD1_CLK */
 			DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP |  0x1)	/* SD1_CMD */
@@ -129,13 +129,13 @@
 			>;
 	};
 
-	usb0_pins: pinmux_usb0_pins {
+	usb0_pins: usb0-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1)	/* USB0_DRVVBUS */
 			>;
 	};
 
-	usb1_pins: pinmux_usb1_pins {
+	usb1_pins: usb1-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80)	/* USB1_DRVVBUS */
 			>;
diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/ti/omap/dm8148-t410.dts
index 9e43d5ec0bb2..f3e2ecf6d723 100644
--- a/arch/arm/boot/dts/dm8148-t410.dts
+++ b/arch/arm/boot/dts/ti/omap/dm8148-t410.dts
@@ -33,12 +33,12 @@
 
 &cpsw_emac0 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 };
 
 &cpsw_emac1 {
 	phy-handle = <&ethphy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 };
 
 &davinci_mdio {
@@ -71,7 +71,7 @@
 };
 
 &pincntl {
-	sd2_pins: pinmux_sd2_pins {
+	sd2_pins: sd2-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x09c0, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[7] */
 			DM814X_IOPAD(0x09c4, PIN_INPUT_PULLUP | 0x1)	/* SD2_DAT[6] */
@@ -87,13 +87,13 @@
 			>;
 	};
 
-	usb0_pins: pinmux_usb0_pins {
+	usb0_pins: usb0-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1)	/* USB0_DRVVBUS */
 			>;
 	};
 
-	usb1_pins: pinmux_usb1_pins {
+	usb1_pins: usb1-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80)	/* USB1_DRVVBUS */
 			>;
diff --git a/arch/arm/boot/dts/dm814x-clocks.dtsi b/arch/arm/boot/dts/ti/omap/dm814x-clocks.dtsi
index e5e4d0affefa..f7939f43413b 100644
--- a/arch/arm/boot/dts/dm814x-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dm814x-clocks.dtsi
@@ -362,4 +362,18 @@
 			#clock-cells = <2>;
 		};
 	};
+
+	alwon_ethernet_cm: alwon_ethernet_cm@15d4 {
+		compatible = "ti,omap4-cm";
+		reg = <0x15d4 0x4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x15d4 0x4>;
+
+		alwon_ethernet_clkctrl: clk@0 {
+			compatible = "ti,clkctrl";
+			reg = <0 0x4>;
+			#clock-cells = <2>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/ti/omap/dm814x.dtsi
index 95de9f214c14..a8cd724ce4bc 100644
--- a/arch/arm/boot/dts/dm814x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dm814x.dtsi
@@ -1,9 +1,7 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/clock/dm814.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/dm814x.h>
 
@@ -165,8 +163,11 @@
 				interrupts = <17>;
 				interrupt-names = "glue";
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <30>;
+				dma-channels = <30>;
 				#dma-requests = <256>;
+				dma-requests = <256>;
 			};
 		};
 
@@ -306,17 +307,33 @@
 				ti,hwmods = "mcspi4";
 			};
 
-			timer1: timer@2e000 {
-				compatible = "ti,dm814-timer";
-				reg = <0x2e000 0x2000>;
-				interrupts = <67>;
-				ti,hwmods = "timer1";
-				ti,timer-alwon;
+			timer1_target: target-module@2e000 {
+				compatible = "ti,sysc-omap4-timer", "ti,sysc";
+				reg = <0x2e000 0x4>,
+				      <0x2e010 0x4>;
+				reg-names = "rev", "sysc";
+				ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+				ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+						<SYSC_IDLE_NO>,
+						<SYSC_IDLE_SMART>,
+						<SYSC_IDLE_SMART_WKUP>;
 				clocks = <&timer1_fck>;
 				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x2e000 0x1000>;
+
+				timer1: timer@0 {
+					compatible = "ti,am335x-timer-1ms";
+					reg = <0x0 0x400>;
+					interrupts = <67>;
+					ti,timer-alwon;
+					clocks = <&timer1_fck>;
+					clock-names = "fck";
+				};
 			};
 
-			uart1: uart@20000 {
+			uart1: serial@20000 {
 				compatible = "ti,am3352-uart", "ti,omap3-uart";
 				ti,hwmods = "uart1";
 				reg = <0x20000 0x2000>;
@@ -326,7 +343,7 @@
 				dma-names = "tx", "rx";
 			};
 
-			uart2: uart@22000 {
+			uart2: serial@22000 {
 				compatible = "ti,am3352-uart", "ti,omap3-uart";
 				ti,hwmods = "uart2";
 				reg = <0x22000 0x2000>;
@@ -336,7 +353,7 @@
 				dma-names = "tx", "rx";
 			};
 
-			uart3: uart@24000 {
+			uart3: serial@24000 {
 				compatible = "ti,am3352-uart", "ti,omap3-uart";
 				ti,hwmods = "uart3";
 				reg = <0x24000 0x2000>;
@@ -346,13 +363,29 @@
 				dma-names = "tx", "rx";
 			};
 
-			timer2: timer@40000 {
-				compatible = "ti,dm814-timer";
-				reg = <0x40000 0x2000>;
-				interrupts = <68>;
-				ti,hwmods = "timer2";
+			timer2_target: target-module@40000 {
+				compatible = "ti,sysc-omap4-timer", "ti,sysc";
+				reg = <0x40000 0x4>,
+				      <0x40010 0x4>;
+				reg-names = "rev", "sysc";
+				ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+				ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+						<SYSC_IDLE_NO>,
+						<SYSC_IDLE_SMART>,
+						<SYSC_IDLE_SMART_WKUP>;
 				clocks = <&timer2_fck>;
 				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x40000 0x1000>;
+
+				timer2: timer@0 {
+					compatible = "ti,dm814-timer";
+					reg = <0 0x1000>;
+					interrupts = <68>;
+					clocks = <&timer2_fck>;
+					clock-names = "fck";
+				};
 			};
 
 			timer3: timer@42000 {
@@ -519,53 +552,123 @@
 			reg = <0x47810000 0x1000>;
 		};
 
-		edma: edma@49000000 {
-			compatible = "ti,edma3-tpcc";
-			ti,hwmods = "tpcc";
-			reg =	<0x49000000 0x10000>;
-			reg-names = "edma3_cc";
-			interrupts = <12 13 14>;
-			interrupt-names = "edma3_ccint", "edma3_mperr",
-					  "edma3_ccerrint";
-			dma-requests = <64>;
-			#dma-cells = <2>;
-
-			ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
-				   <&edma_tptc2 3>, <&edma_tptc3 0>;
-
-			ti,edma-memcpy-channels = <20 21>;
+		target-module@49000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49000000 0x4>;
+			reg-names = "rev";
+			clocks = <&alwon_clkctrl DM814_TPCC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49000000 0x10000>;
+
+			edma: dma@0 {
+				compatible = "ti,edma3-tpcc";
+				reg = <0 0x10000>;
+				reg-names = "edma3_cc";
+				interrupts = <12 13 14>;
+				interrupt-names = "edma3_ccint", "edma3_mperr",
+						  "edma3_ccerrint";
+				dma-requests = <64>;
+				#dma-cells = <2>;
+
+				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
+					   <&edma_tptc2 3>, <&edma_tptc3 0>;
+
+				ti,edma-memcpy-channels = <20 21>;
+			};
 		};
 
-		edma_tptc0: tptc@49800000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc0";
-			reg =	<0x49800000 0x100000>;
-			interrupts = <112>;
-			interrupt-names = "edma3_tcerrint";
+		target-module@49800000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49800000 0x4>,
+			      <0x49800010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM814_TPTC0_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49800000 0x100000>;
+
+			edma_tptc0: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <112>;
+				interrupt-names = "edma3_tcerrint";
+			};
 		};
 
-		edma_tptc1: tptc@49900000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc1";
-			reg =	<0x49900000 0x100000>;
-			interrupts = <113>;
-			interrupt-names = "edma3_tcerrint";
+		target-module@49900000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49900000 0x4>,
+			      <0x49900010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM814_TPTC1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49900000 0x100000>;
+
+			edma_tptc1: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <113>;
+				interrupt-names = "edma3_tcerrint";
+			};
 		};
 
-		edma_tptc2: tptc@49a00000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc2";
-			reg =	<0x49a00000 0x100000>;
-			interrupts = <114>;
-			interrupt-names = "edma3_tcerrint";
+		target-module@49a00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49a00000 0x4>,
+			      <0x49a00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM814_TPTC2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49a00000 0x100000>;
+
+			edma_tptc2: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <114>;
+				interrupt-names = "edma3_tcerrint";
+			};
 		};
 
-		edma_tptc3: tptc@49b00000 {
-			compatible = "ti,edma3-tptc";
-			ti,hwmods = "tptc3";
-			reg =	<0x49b00000 0x100000>;
-			interrupts = <115>;
-			interrupt-names = "edma3_tcerrint";
+		target-module@49b00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49b00000 0x4>,
+			      <0x49b00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM814_TPTC3_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49b00000 0x100000>;
+
+			edma_tptc3: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <115>;
+				interrupt-names = "edma3_tcerrint";
+			};
 		};
 
 		/* See TRM "Table 1-318. L4HS Instance Summary" */
@@ -574,57 +677,73 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x4a000000 0x1b4040>;
-		};
-
-		/* REVISIT: Move to live under l4hs once driver is fixed */
-		mac: ethernet@4a100000 {
-			compatible = "ti,cpsw";
-			ti,hwmods = "cpgmac0";
-			clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
-			clock-names = "fck", "cpts";
-			cpdma_channels = <8>;
-			ale_entries = <1024>;
-			bd_ram_size = <0x2000>;
-			mac_control = <0x20>;
-			slaves = <2>;
-			active_slave = <0>;
-			cpts_clock_mult = <0x80000000>;
-			cpts_clock_shift = <29>;
-			reg = <0x4a100000 0x800
-			       0x4a100900 0x100>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			interrupt-parent = <&intc>;
-			/*
-			 * c0_rx_thresh_pend
-			 * c0_rx_pend
-			 * c0_tx_pend
-			 * c0_misc_pend
-			 */
-			interrupts = <40 41 42 43>;
-			ranges;
-			syscon = <&scm_conf>;
 
-			davinci_mdio: mdio@4a100800 {
-				compatible = "ti,davinci_mdio";
+			target-module@100000 {
+				compatible = "ti,sysc-omap4-simple", "ti,sysc";
+				reg = <0x100900 0x4>,
+				      <0x100908 0x4>,
+				      <0x100904 0x4>;
+				reg-names = "rev", "sysc", "syss";
+				ti,sysc-mask = <0>;
+				ti,sysc-midle = <SYSC_IDLE_FORCE>,
+						<SYSC_IDLE_NO>;
+				ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+						<SYSC_IDLE_NO>;
+				ti,syss-mask = <1>;
+				clocks = <&alwon_ethernet_clkctrl DM814_ETHERNET_CPGMAC0_CLKCTRL 0>;
+				clock-names = "fck";
 				#address-cells = <1>;
-				#size-cells = <0>;
-				ti,hwmods = "davinci_mdio";
-				bus_freq = <1000000>;
-				reg = <0x4a100800 0x100>;
-			};
-
-			cpsw_emac0: slave@4a100200 {
-				/* Filled in by U-Boot */
-				mac-address = [ 00 00 00 00 00 00 ];
-				phys = <&phy_gmii_sel 1>;
+				#size-cells = <1>;
+				ranges = <0 0x100000 0x8000>;
+
+				mac: ethernet@0 {
+					compatible = "ti,cpsw";
+					clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
+					clock-names = "fck", "cpts";
+					cpdma_channels = <8>;
+					ale_entries = <1024>;
+					bd_ram_size = <0x2000>;
+					mac_control = <0x20>;
+					slaves = <2>;
+					active_slave = <0>;
+					cpts_clock_mult = <0x80000000>;
+					cpts_clock_shift = <29>;
+					reg = <0 0x800>,
+					      <0x900 0x100>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					/*
+					* c0_rx_thresh_pend
+					* c0_rx_pend
+					* c0_tx_pend
+					* c0_misc_pend
+					*/
+					interrupts = <40 41 42 43>;
+					ranges = <0 0 0x8000>;
+					syscon = <&scm_conf>;
+
+					davinci_mdio: mdio@800 {
+						compatible = "ti,cpsw-mdio", "ti,davinci_mdio";
+						clocks = <&cpsw_125mhz_gclk>;
+						clock-names = "fck";
+						#address-cells = <1>;
+						#size-cells = <0>;
+						bus_freq = <1000000>;
+						reg = <0x800 0x100>;
+					};
 
-			};
+					cpsw_emac0: slave@200 {
+						/* Filled in by U-Boot */
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 1>;
+					};
 
-			cpsw_emac1: slave@4a100300 {
-				/* Filled in by U-Boot */
-				mac-address = [ 00 00 00 00 00 00 ];
-				phys = <&phy_gmii_sel 2>;
+					cpsw_emac1: slave@300 {
+						/* Filled in by U-Boot */
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 2>;
+					};
+				};
 			};
 		};
 
@@ -647,3 +766,23 @@
 };
 
 #include "dm814x-clocks.dtsi"
+
+/* Preferred always-on timer for clocksource */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer1_fck>;
+		assigned-clock-parents = <&devosc_ck>;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer2_fck>;
+		assigned-clock-parents = <&devosc_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/ti/omap/dm8168-evm.dts
index cf05d532db65..1d80288f6ba5 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dm8168-evm.dts
@@ -30,7 +30,7 @@
 };
 
 &dm816x_pinmux {
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0a94, MUX_MODE0)			/* SPI_SCLK */
 			DM816X_IOPAD(0x0a98, MUX_MODE0)			/* SPI_SCS0 */
@@ -39,7 +39,7 @@
 		>;
 	};
 
-	mmc_pins: pinmux_mmc_pins {
+	mmc_pins: mmc-pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0a70, MUX_MODE0)			/* SD_POW */
 			DM816X_IOPAD(0x0a74, MUX_MODE0)			/* SD_CLK */
@@ -53,19 +53,19 @@
 		>;
 	};
 
-	usb0_pins: pinmux_usb0_pins {
+	usb0_pins: usb0-pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0d04, MUX_MODE0)			/* USB0_DRVVBUS */
 		>;
 	};
 
-	usb1_pins: pinmux_usb1_pins {
+	usb1_pins: usb1-pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0d08, MUX_MODE0)			/* USB1_DRVVBUS */
 		>;
 	};
 
-	nandflash_pins: nandflash_pins {
+	nandflash_pins: nandflash-pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0b38, PULL_UP | MUX_MODE0)		/* PINCTRL207 GPMC_CS0*/
 			DM816X_IOPAD(0x0b60, PULL_ENA | MUX_MODE0)		/* PINCTRL217 GPMC_ADV_ALE */
@@ -119,7 +119,7 @@
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
-		linux,mtd-name= "micron,mt29f2g16aadwp";
+		linux,mtd-name = "micron,mt29f2g16aadwp";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
@@ -154,19 +154,19 @@
 			label = "X-Loader";
 			reg = <0 0x80000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "U-Boot";
 			reg = <0x80000 0x1c0000>;
 		};
-		partition@0x1c0000 {
+		partition@1c0000 {
 			label = "Environment";
 			reg = <0x240000 0x40000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "Kernel";
 			reg = <0x280000 0x500000>;
 		};
-		partition@0x780000 {
+		partition@780000 {
 			label = "Filesystem";
 			reg = <0x780000 0xf880000>;
 		};
@@ -177,7 +177,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcspi1_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "w25x32";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dm816x-clocks.dtsi b/arch/arm/boot/dts/ti/omap/dm816x-clocks.dtsi
index 338449b32a18..338449b32a18 100644
--- a/arch/arm/boot/dts/dm816x-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dm816x-clocks.dtsi
diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/ti/omap/dm816x.dtsi
index 1edc2b48b254..b68686f0643b 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dm816x.dtsi
@@ -1,9 +1,7 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/clock/dm816.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/omap.h>
 
@@ -138,13 +136,123 @@
 			};
 		};
 
-		edma: edma@49000000 {
-			compatible = "ti,edma3";
-			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2", "tptc3";
-			reg =   <0x49000000 0x10000>,
-			        <0x44e10f90 0x40>;
-			interrupts = <12 13 14>;
-			#dma-cells = <1>;
+		target-module@49000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49000000 0x4>;
+			reg-names = "rev";
+			clocks = <&alwon_clkctrl DM816_TPCC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49000000 0x10000>;
+
+			edma: dma@0 {
+				compatible = "ti,edma3-tpcc";
+				reg = <0 0x10000>;
+				reg-names = "edma3_cc";
+				interrupts = <12 13 14>;
+				interrupt-names = "edma3_ccint", "edma3_mperr",
+						  "edma3_ccerrint";
+				dma-requests = <64>;
+				#dma-cells = <2>;
+
+				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
+					   <&edma_tptc2 3>, <&edma_tptc3 0>;
+
+				ti,edma-memcpy-channels = <20 21>;
+			};
+		};
+
+		target-module@49800000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49800000 0x4>,
+			      <0x49800010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC0_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49800000 0x100000>;
+
+			edma_tptc0: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <112>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49900000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49900000 0x4>,
+			      <0x49900010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49900000 0x100000>;
+
+			edma_tptc1: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <113>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49a00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49a00000 0x4>,
+			      <0x49a00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49a00000 0x100000>;
+
+			edma_tptc2: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <114>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@49b00000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x49b00000 0x4>,
+			      <0x49b00010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&alwon_clkctrl DM816_TPTC3_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49b00000 0x100000>;
+
+			edma_tptc3: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <115>;
+				interrupt-names = "edma3_tcerrint";
+			};
 		};
 
 		elm: elm@48080000 {
@@ -185,7 +293,7 @@
 			#address-cells = <2>;
 			#size-cells = <1>;
 			interrupts = <100>;
-			dmas = <&edma 52>;
+			dmas = <&edma 52 0>;
 			dma-names = "rxtx";
 			gpmc,num-cs = <6>;
 			gpmc,num-waitpins = <2>;
@@ -202,8 +310,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <70>;
-			dmas = <&edma 58 &edma 59>;
-			dma-names = "tx", "rx";
 		};
 
 		i2c2: i2c@4802a000 {
@@ -213,8 +319,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <71>;
-			dmas = <&edma 60 &edma 61>;
-			dma-names = "tx", "rx";
 		};
 
 		intc: interrupt-controller@48200000 {
@@ -239,7 +343,7 @@
 			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <12>;
-			mbox_dsp: mbox_dsp {
+			mbox_dsp: mbox-dsp {
 				ti,mbox-tx = <3 0 0>;
 				ti,mbox-rx = <0 0 0>;
 			};
@@ -311,10 +415,10 @@
 			interrupts = <65>;
 			ti,spi-num-cs = <4>;
 			ti,hwmods = "mcspi1";
-			dmas = <&edma 16 &edma 17
-				&edma 18 &edma 19
-				&edma 20 &edma 21
-				&edma 22 &edma 23>;
+			dmas = <&edma 16 0 &edma 17 0
+				&edma 18 0 &edma 19 0
+				&edma 20 0 &edma 21 0
+				&edma 22 0 &edma 23 0>;
 			dma-names = "tx0", "rx0", "tx1", "rx1",
 				    "tx2", "rx2", "tx3", "rx3";
 		};
@@ -324,27 +428,59 @@
 			reg = <0x48060000 0x11000>;
 			ti,hwmods = "mmc1";
 			interrupts = <64>;
-			dmas = <&edma 24 &edma 25>;
+			dmas = <&edma 24 0 &edma 25 0>;
 			dma-names = "tx", "rx";
 		};
 
-		timer1: timer@4802e000 {
-			compatible = "ti,dm816-timer";
-			reg = <0x4802e000 0x2000>;
-			interrupts = <67>;
-			ti,hwmods = "timer1";
-			ti,timer-alwon;
-			clocks = <&timer1_fck>;
+		timer1_target: target-module@4802e000 {
+			compatible = "ti,sysc-omap4-timer", "ti,sysc";
+			reg = <0x4802e000 0x4>,
+			      <0x4802e010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&alwon_clkctrl DM816_TIMER1_CLKCTRL 0>;
 			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4802e000 0x1000>;
+
+			timer1: timer@0 {
+				compatible = "ti,dm816-timer";
+				reg = <0 0x1000>;
+				interrupts = <67>;
+				ti,timer-alwon;
+				clocks = <&alwon_clkctrl DM816_TIMER1_CLKCTRL 0>;
+				clock-names = "fck";
+			};
 		};
 
-		timer2: timer@48040000 {
-			compatible = "ti,dm816-timer";
-			reg = <0x48040000 0x2000>;
-			interrupts = <68>;
-			ti,hwmods = "timer2";
-			clocks = <&timer2_fck>;
+		timer2_target: target-module@48040000 {
+			compatible = "ti,sysc-omap4-timer", "ti,sysc";
+			reg = <0x48040000 0x4>,
+			      <0x48040010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&alwon_clkctrl DM816_TIMER2_CLKCTRL 0>;
 			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x48040000 0x1000>;
+
+			timer2: timer@0 {
+				compatible = "ti,dm816-timer";
+				reg = <0 0x1000>;
+				interrupts = <68>;
+				clocks = <&alwon_clkctrl DM816_TIMER2_CLKCTRL 0>;
+				clock-names = "fck";
+			};
 		};
 
 		timer3: timer@48042000 {
@@ -386,33 +522,33 @@
 			ti,timer-pwm;
 		};
 
-		uart1: uart@48020000 {
+		uart1: serial@48020000 {
 			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart1";
 			reg = <0x48020000 0x2000>;
 			clock-frequency = <48000000>;
 			interrupts = <72>;
-			dmas = <&edma 26 &edma 27>;
+			dmas = <&edma 26 0 &edma 27 0>;
 			dma-names = "tx", "rx";
 		};
 
-		uart2: uart@48022000 {
+		uart2: serial@48022000 {
 			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart2";
 			reg = <0x48022000 0x2000>;
 			clock-frequency = <48000000>;
 			interrupts = <73>;
-			dmas = <&edma 28 &edma 29>;
+			dmas = <&edma 28 0 &edma 29 0>;
 			dma-names = "tx", "rx";
 		};
 
-		uart3: uart@48024000 {
+		uart3: serial@48024000 {
 			compatible = "ti,am3352-uart", "ti,omap3-uart";
 			ti,hwmods = "uart3";
 			reg = <0x48024000 0x2000>;
 			clock-frequency = <48000000>;
 			interrupts = <74>;
-			dmas = <&edma 30 &edma 31>;
+			dmas = <&edma 30 0 &edma 31 0>;
 			dma-names = "tx", "rx";
 		};
 
@@ -515,8 +651,11 @@
 				interrupts = <17>;
 				interrupt-names = "glue";
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <30>;
+				dma-channels = <30>;
 				#dma-requests = <256>;
+				dma-requests = <256>;
 			};
 		};
 
@@ -530,3 +669,23 @@
 };
 
 #include "dm816x-clocks.dtsi"
+
+/* Preferred always-on timer for clocksource */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer1_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&timer2_fck>;
+		assigned-clock-parents = <&sys_clkin_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/dra62x-clocks.dtsi b/arch/arm/boot/dts/ti/omap/dra62x-clocks.dtsi
index 11d1241b0e13..11d1241b0e13 100644
--- a/arch/arm/boot/dts/dra62x-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra62x-clocks.dtsi
diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/ti/omap/dra62x-j5eco-evm.dts
index 861ab90a3f3a..2f6ac267fc15 100644
--- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dra62x-j5eco-evm.dts
@@ -24,12 +24,12 @@
 
 &cpsw_emac0 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 };
 
 &cpsw_emac1 {
 	phy-handle = <&ethphy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 };
 
 &davinci_mdio {
@@ -51,7 +51,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
-		linux,mtd-name= "micron,mt29f2g16aadwp";
+		linux,mtd-name = "micron,mt29f2g16aadwp";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "bch8";
@@ -108,7 +108,7 @@
 };
 
 &pincntl {
-	sd1_pins: pinmux_sd1_pins {
+	sd1_pins: sd1-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0800, PIN_INPUT | 0x1)	/* SD1_CLK */
 			DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP |  0x1)	/* SD1_CMD */
@@ -121,7 +121,7 @@
 			>;
 	};
 
-	usb0_pins: pinmux_usb0_pins {
+	usb0_pins: usb0-pins {
 		pinctrl-single,pins = <
 			DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1)	/* USB0_DRVVBUS */
 			>;
diff --git a/arch/arm/boot/dts/ti/omap/dra62x.dtsi b/arch/arm/boot/dts/ti/omap/dra62x.dtsi
new file mode 100644
index 000000000000..cfefa670515c
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra62x.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "dm814x.dtsi"
+
+/ {
+	compatible = "ti,dra62x";
+};
+
+/* Compared to dm814x, dra62x has different offsets for Ethernet */
+&mac {
+	reg = <0 0x800>,
+	      <0x1200 0x100>;
+};
+
+&davinci_mdio {
+	reg = <0x1000 0x100>;
+};
+
+#include "dra62x-clocks.dtsi"
diff --git a/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi b/arch/arm/boot/dts/ti/omap/dra7-dspeve-thermal.dtsi
index 1c39a8459b39..747ff0db90c7 100644
--- a/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7-dspeve-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for DRA7x SoC DSPEVE thermal
  *
- * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/dra7-evm-common.dtsi b/arch/arm/boot/dts/ti/omap/dra7-evm-common.dtsi
index 82eeba8faef1..ed5199d7acd8 100644
--- a/arch/arm/boot/dts/dra7-evm-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7-evm-common.dtsi
@@ -1,10 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+#include "dra74-ipu-dsp-common.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/clock/ti-dra7-atl.h>
 #include <dt-bindings/input/input.h>
 
 / {
@@ -14,12 +15,12 @@
 
 	extcon_usb1: extcon_usb1 {
 		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
+		id-gpios = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
 	};
 
 	extcon_usb2: extcon_usb2 {
 		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
+		id-gpios = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
 	};
 
 	sound0: sound0 {
@@ -134,7 +135,7 @@
 	status = "okay";
 
 	spi-max-frequency = <76800000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "s25fl256s1";
 		spi-max-frequency = <76800000>;
 		reg = <0>;
@@ -150,7 +151,7 @@
 		 */
 		partition@0 {
 			label = "QSPI.SPL";
-			reg = <0x00000000 0x000010000>;
+			reg = <0x00000000 0x00010000>;
 		};
 		partition@1 {
 			label = "QSPI.SPL.backup1";
@@ -244,26 +245,6 @@
 	rx-num-evt = <32>;
 };
 
-&mailbox5 {
-	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
-};
-
-&mailbox6 {
-	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		status = "okay";
-	};
-};
-
 &pcie1_rc {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/ti/omap/dra7-evm.dts
index de7f85efaa51..46efbaa67a8e 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dra7-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -35,6 +35,40 @@
 		regulator-max-microvolt = <1800000>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp2_memory_region: dsp2-memory@9f000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9f000000 0x0 0x800000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	evm_3v3_sd: fixedregulator-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "evm_3v3_sd";
@@ -61,10 +95,10 @@
 		regulator-max-microvolt = <1800000>;
 	};
 
-	evm_3v3: fixedregulator-evm3v3 {
+	vsys_3v3: fixedregulator-vsys3v3 {
 		/* Output of Cntlr A of TPS43351-Q1 on dra7-evm */
 		compatible = "regulator-fixed";
-		regulator-name = "evm_3v3";
+		regulator-name = "vsys_3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&evm_12v0>;
@@ -118,14 +152,14 @@
 };
 
 &dra7_pmx_core {
-	dcan1_pins_default: dcan1_pins_default {
+	dcan1_pins_default: dcan1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
 			DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
 		>;
 	};
 
-	dcan1_pins_sleep: dcan1_pins_sleep {
+	dcan1_pins_sleep: dcan1-sleep-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
 			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
@@ -285,7 +319,7 @@
 	};
 
 	pcf_lcd: gpio@20 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x20>;
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -296,7 +330,7 @@
 	};
 
 	pcf_gpio_21: gpio@21 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x21>;
 		lines-initial-states = <0x1408>;
 		gpio-controller;
@@ -328,11 +362,11 @@
 	clock-frequency = <400000>;
 
 	pcf_hdmi: gpio@26 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x26>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		p1 {
+		hdmi-audio-hog {
 			/* vin6_sel_s0: high: VIN6, low: audio */
 			gpio-hog;
 			gpios = <1 GPIO_ACTIVE_HIGH>;
@@ -449,7 +483,7 @@
 		#size-cells = <1>;
 		partition@0 {
 			label = "NAND.SPL";
-			reg = <0x00000000 0x000020000>;
+			reg = <0x00000000 0x00020000>;
 		};
 		partition@1 {
 			label = "NAND.SPL.backup1";
@@ -503,24 +537,23 @@
 	ti,no-idle-on-init;
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
-	dual_emac;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	ethphy0: ethernet-phy@2 {
 		reg = <2>;
 	};
@@ -531,9 +564,29 @@
 };
 
 &dcan1 {
-	status = "ok";
+	status = "okay";
 	pinctrl-names = "default", "sleep", "active";
 	pinctrl-0 = <&dcan1_pins_sleep>;
 	pinctrl-1 = <&dcan1_pins_sleep>;
 	pinctrl-2 = <&dcan1_pins_default>;
 };
+
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_memory_region>;
+};
+
+&ipu1 {
+	status = "okay";
+	memory-region = <&ipu1_memory_region>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_memory_region>;
+};
+
+&dsp2 {
+	status = "okay";
+	memory-region = <&dsp2_memory_region>;
+};
diff --git a/arch/arm/boot/dts/ti/omap/dra7-ipu-dsp-common.dtsi b/arch/arm/boot/dts/ti/omap/dra7-ipu-dsp-common.dtsi
new file mode 100644
index 000000000000..a5bdc6431d8d
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra7-ipu-dsp-common.dtsi
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common IPU and DSP data for TI DRA7xx/AM57xx platforms
+ */
+
+&mailbox5 {
+	status = "okay";
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
+		status = "okay";
+	};
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
+		status = "okay";
+	};
+};
+
+&mailbox6 {
+	status = "okay";
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
+		status = "okay";
+	};
+};
+
+&ipu2 {
+	mboxes = <&mailbox6 &mbox_ipu2_ipc3x>;
+	ti,timers = <&timer3>;
+	ti,watchdog-timers = <&timer4>, <&timer9>;
+};
+
+&ipu1 {
+	mboxes = <&mailbox5 &mbox_ipu1_ipc3x>;
+	ti,timers = <&timer11>;
+	ti,watchdog-timers = <&timer7>, <&timer8>;
+};
+
+&dsp1 {
+	mboxes = <&mailbox5 &mbox_dsp1_ipc3x>;
+	ti,timers = <&timer5>;
+	ti,watchdog-timers = <&timer10>;
+};
diff --git a/arch/arm/boot/dts/dra7-iva-thermal.dtsi b/arch/arm/boot/dts/ti/omap/dra7-iva-thermal.dtsi
index dd74a5337d1f..0a31313065df 100644
--- a/arch/arm/boot/dts/dra7-iva-thermal.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7-iva-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for DRA7x SoC IVA thermal
  *
- * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/ti/omap/dra7-l4.dtsi
index 7e7aa101d8a4..5733e3a4ea8e 100644
--- a/arch/arm/boot/dts/dra7-l4.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7-l4.dtsi
@@ -1,5 +1,8 @@
 &l4_cfg {						/* 0x4a000000 */
-	compatible = "ti,dra7-l4-cfg", "simple-bus";
+	compatible = "ti,dra7-l4-cfg", "simple-pm-bus";
+	power-domains = <&prm_coreaon>;
+	clocks = <&l4cfg_clkctrl DRA7_L4CFG_L4_CFG_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4a000000 0x800>,
 	      <0x4a000800 0x800>,
 	      <0x4a001000 0x1000>;
@@ -11,7 +14,7 @@
 		 <0x00200000 0x4a200000 0x100000>;	/* segment 2 */
 
 	segment@0 {					/* 0x4a000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -186,7 +189,6 @@
 
 		target-module@56000 {			/* 0x4a056000, ap 9 02.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "dma_system";
 			reg = <0x56000 0x4>,
 			      <0x5602c 0x4>,
 			      <0x56028 0x4>;
@@ -212,7 +214,7 @@
 			ranges = <0x0 0x56000 0x1000>;
 
 			sdma: dma-controller@0 {
-				compatible = "ti,omap4430-sdma";
+				compatible = "ti,omap4430-sdma", "ti,omap-sdma";
 				reg = <0x0 0x1000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
@@ -234,7 +236,6 @@
 
 		target-module@80000 {			/* 0x4a080000, ap 13 20.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "ocp2scp1";
 			reg = <0x80000 0x4>,
 			      <0x80010 0x4>,
 			      <0x80014 0x4>;
@@ -302,7 +303,6 @@
 
 		target-module@90000 {			/* 0x4a090000, ap 59 42.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "ocp2scp3";
 			reg = <0x90000 0x4>,
 			      <0x90010 0x4>,
 			      <0x90014 0x4>;
@@ -394,7 +394,6 @@
 
 		target-module@d9000 {			/* 0x4a0d9000, ap 17 72.0 */
 			compatible = "ti,sysc-omap4-sr", "ti,sysc";
-			ti,hwmods = "smartreflex_mpu";
 			reg = <0xd9038 0x4>;
 			reg-names = "sysc";
 			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
@@ -414,7 +413,6 @@
 
 		target-module@dd000 {			/* 0x4a0dd000, ap 19 18.0 */
 			compatible = "ti,sysc-omap4-sr", "ti,sysc";
-			ti,hwmods = "smartreflex_core";
 			reg = <0xdd038 0x4>;
 			reg-names = "sysc";
 			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
@@ -471,7 +469,6 @@
 
 		target-module@f6000 {			/* 0x4a0f6000, ap 25 78.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spinlock";
 			reg = <0xf6000 0x4>,
 			      <0xf6010 0x4>,
 			      <0xf6014 0x4>;
@@ -499,7 +496,7 @@
 	};
 
 	segment@100000 {					/* 0x4a100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00002000 0x00102000 0x001000>,	/* ap 27 */
@@ -578,11 +575,33 @@
 		};
 
 		target-module@40000 {			/* 0x4a140000, ap 31 06.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
-			#address-cells = <1>;
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x400fc 4>,
+			      <0x41100 4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			power-domains = <&prm_l3init>;
+			clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 0>;
+			clock-names = "fck";
 			#size-cells = <1>;
+			#address-cells = <1>;
 			ranges = <0x0 0x40000 0x10000>;
+
+			sata: sata@0 {
+				compatible = "snps,dwc-ahci";
+				reg = <0 0x1100>, <0x1100 0x8>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&sata_phy>;
+				phy-names = "sata-phy";
+				clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 8>;
+				ports-implemented = <0x1>;
+			};
 		};
 
 		target-module@51000 {			/* 0x4a151000, ap 33 50.0 */
@@ -795,7 +814,7 @@
 	};
 
 	segment@200000 {					/* 0x4a200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00018000 0x00218000 0x001000>,	/* ap 43 */
@@ -1012,7 +1031,10 @@
 };
 
 &l4_per1 {						/* 0x48000000 */
-	compatible = "ti,dra7-l4-per1", "simple-bus";
+	compatible = "ti,dra7-l4-per1", "simple-pm-bus";
+	power-domains = <&prm_l4per>;
+	clocks = <&l4per_clkctrl DRA7_L4PER_L4_PER1_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48000000 0x800>,
 	      <0x48000800 0x800>,
 	      <0x48001000 0x400>,
@@ -1026,7 +1048,7 @@
 		 <0x00200000 0x48200000 0x200000>;	/* segment 1 */
 
 	segment@0 {					/* 0x48000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -1137,7 +1159,7 @@
 			ranges = <0x0 0x20000 0x1000>;
 
 			uart3: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -1149,7 +1171,6 @@
 
 		target-module@32000 {			/* 0x48032000, ap 5 3e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer2";
 			reg = <0x32000 0x4>,
 			      <0x32010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1169,15 +1190,14 @@
 			timer2: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER2_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER2_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
-		target-module@34000 {			/* 0x48034000, ap 7 46.0 */
+		timer3_target: target-module@34000 {	/* 0x48034000, ap 7 46.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer3";
 			reg = <0x34000 0x4>,
 			      <0x34010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1197,15 +1217,14 @@
 			timer3: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER3_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER3_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
-		target-module@36000 {			/* 0x48036000, ap 9 4e.0 */
+		timer4_target: target-module@36000 {	/* 0x48036000, ap 9 4e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer4";
 			reg = <0x36000 0x4>,
 			      <0x36010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1225,15 +1244,14 @@
 			timer4: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER4_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER4_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@3e000 {			/* 0x4803e000, ap 11 56.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer9";
 			reg = <0x3e000 0x4>,
 			      <0x3e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1253,8 +1271,8 @@
 			timer9: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER9_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER9_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -1325,7 +1343,7 @@
 			};
 		};
 
-		target-module@55000 {			/* 0x48055000, ap 13 0e.0 */
+		gpio2_target: target-module@55000 {		/* 0x48055000, ap 13 0e.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x55000 0x4>,
 			      <0x55010 0x4>,
@@ -1358,7 +1376,7 @@
 			};
 		};
 
-		target-module@57000 {			/* 0x48057000, ap 15 06.0 */
+		gpio3_target: target-module@57000 {		/* 0x48057000, ap 15 06.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x57000 0x4>,
 			      <0x57010 0x4>,
@@ -1544,7 +1562,7 @@
 			ranges = <0x0 0x66000 0x1000>;
 
 			uart5: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -1576,7 +1594,7 @@
 			ranges = <0x0 0x68000 0x1000>;
 
 			uart6: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -1608,7 +1626,7 @@
 			ranges = <0x0 0x6a000 0x1000>;
 
 			uart1: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -1640,7 +1658,7 @@
 			ranges = <0x0 0x6c000 0x1000>;
 
 			uart2: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -1672,7 +1690,7 @@
 			ranges = <0x0 0x6e000 0x1000>;
 
 			uart4: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -1748,7 +1766,6 @@
 
 		target-module@78000 {			/* 0x48078000, ap 39 0a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "elm";
 			reg = <0x78000 0x4>,
 			      <0x78010 0x4>,
 			      <0x78014 0x4>;
@@ -1842,7 +1859,6 @@
 
 		target-module@86000 {			/* 0x48086000, ap 41 5e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer10";
 			reg = <0x86000 0x4>,
 			      <0x86010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1862,15 +1878,14 @@
 			timer10: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER10_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER10_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@88000 {			/* 0x48088000, ap 43 66.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer11";
 			reg = <0x88000 0x4>,
 			      <0x88010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1890,8 +1905,8 @@
 			timer11: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER11_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl DRA7_L4PER_TIMER11_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -2044,6 +2059,37 @@
 				 <0x00001000 0x000a5000 0x00001000>;
 		};
 
+		des_target: target-module@a5000 {	/* 0x480a5000 */
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0xa5030 0x4>,
+			      <0xa5034 0x4>,
+			      <0xa5038 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl DRA7_L4SEC_DES_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xa5000 0x00001000>;
+
+			des: des@0 {
+				compatible = "ti,omap4-des";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma_xbar 117>, <&sdma_xbar 116>;
+				dma-names = "tx", "rx";
+				clocks = <&l3_iclk_div>;
+				clock-names = "fck";
+			};
+		};
+
 		target-module@a8000 {			/* 0x480a8000, ap 59 1a.0 */
 			compatible = "ti,sysc";
 			status = "disabled";
@@ -2251,14 +2297,17 @@
 	};
 
 	segment@200000 {					/* 0x48200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 };
 
 &l4_per2 {						/* 0x48400000 */
-	compatible = "ti,dra7-l4-per2", "simple-bus";
+	compatible = "ti,dra7-l4-per2", "simple-pm-bus";
+	power-domains = <&prm_l4per>;
+	clocks = <&l4per2_clkctrl DRA7_L4PER2_L4_PER2_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48400000 0x800>,
 	      <0x48400800 0x800>,
 	      <0x48401000 0x400>,
@@ -2278,7 +2327,7 @@
 		 <0x48454000 0x48454000 0x400000>;	/* L3 data port */
 
 	segment@0 {					/* 0x48400000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -2375,7 +2424,7 @@
 			ranges = <0x0 0x20000 0x1000>;
 
 			uart7: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -2405,7 +2454,7 @@
 			ranges = <0x0 0x22000 0x1000>;
 
 			uart8: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -2435,7 +2484,7 @@
 			ranges = <0x0 0x24000 0x1000>;
 
 			uart9: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -2490,7 +2539,6 @@
 
 		target-module@3e000 {			/* 0x4843e000, ap 25 30.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss0";
 			reg = <0x3e000 0x4>,
 			      <0x3e004 0x4>;
 			reg-names = "rev", "sysc";
@@ -2513,7 +2561,7 @@
 				status = "disabled";
 				ranges = <0 0 0x1000>;
 
-				ecap0: ecap@100 {
+				ecap0: pwm@100 {
 					compatible = "ti,dra746-ecap",
 						     "ti,am3352-ecap";
 					#pwm-cells = <3>;
@@ -2537,7 +2585,6 @@
 
 		target-module@40000 {			/* 0x48440000, ap 27 38.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss1";
 			reg = <0x40000 0x4>,
 			      <0x40004 0x4>;
 			reg-names = "rev", "sysc";
@@ -2560,7 +2607,7 @@
 				status = "disabled";
 				ranges = <0 0 0x1000>;
 
-				ecap1: ecap@100 {
+				ecap1: pwm@100 {
 					compatible = "ti,dra746-ecap",
 						     "ti,am3352-ecap";
 					#pwm-cells = <3>;
@@ -2584,7 +2631,6 @@
 
 		target-module@42000 {			/* 0x48442000, ap 29 20.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "epwmss2";
 			reg = <0x42000 0x4>,
 			      <0x42004 0x4>;
 			reg-names = "rev", "sysc";
@@ -2607,7 +2653,7 @@
 				status = "disabled";
 				ranges = <0 0 0x1000>;
 
-				ecap2: ecap@100 {
+				ecap2: pwm@100 {
 					compatible = "ti,dra746-ecap",
 						     "ti,am3352-ecap";
 					#pwm-cells = <3>;
@@ -3023,60 +3069,6 @@
 			 */
 			ti,no-idle;
 
-			mac: ethernet@0 {
-				compatible = "ti,dra7-cpsw","ti,cpsw";
-				clocks = <&gmac_main_clk>, <&gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 25>;
-				clock-names = "fck", "cpts";
-				cpdma_channels = <8>;
-				ale_entries = <1024>;
-				bd_ram_size = <0x2000>;
-				mac_control = <0x20>;
-				slaves = <2>;
-				active_slave = <0>;
-				cpts_clock_mult = <0x784CFE14>;
-				cpts_clock_shift = <29>;
-				reg = <0x0 0x1000
-				       0x1200 0x2e00>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-
-				/*
-				 * rx_thresh_pend
-				 * rx_pend
-				 * tx_pend
-				 * misc_pend
-				 */
-				interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>;
-				ranges = <0 0 0x4000>;
-				syscon = <&scm_conf>;
-				status = "disabled";
-
-				davinci_mdio: mdio@1000 {
-					compatible = "ti,cpsw-mdio","ti,davinci_mdio";
-					clocks = <&gmac_main_clk>;
-					clock-names = "fck";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					bus_freq = <1000000>;
-					reg = <0x1000 0x100>;
-				};
-
-				cpsw_emac0: slave@200 {
-					/* Filled in by U-Boot */
-					mac-address = [ 00 00 00 00 00 00 ];
-					phys = <&phy_gmii_sel 1>;
-				};
-
-				cpsw_emac1: slave@300 {
-					/* Filled in by U-Boot */
-					mac-address = [ 00 00 00 00 00 00 ];
-					phys = <&phy_gmii_sel 2>;
-				};
-			};
-
 			mac_sw: switch@0 {
 				compatible = "ti,dra7-cpsw-switch","ti,cpsw-switch";
 				reg = <0x0 0x4000>;
@@ -3133,7 +3125,10 @@
 };
 
 &l4_per3 {						/* 0x48800000 */
-	compatible = "ti,dra7-l4-per3", "simple-bus";
+	compatible = "ti,dra7-l4-per3", "simple-pm-bus";
+	power-domains = <&prm_l4per>;
+	clocks = <&l4per3_clkctrl DRA7_L4PER3_L4_PER3_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48800000 0x800>,
 	      <0x48800800 0x800>,
 	      <0x48801000 0x400>,
@@ -3145,7 +3140,7 @@
 	ranges = <0x00000000 0x48800000 0x200000>;	/* segment 0 */
 
 	segment@0 {					/* 0x48800000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -3326,7 +3321,6 @@
 
 		target-module@20000 {			/* 0x48820000, ap 5 08.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer5";
 			reg = <0x20000 0x4>,
 			      <0x20010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3346,15 +3340,14 @@
 			timer5: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&ipu_clkctrl DRA7_IPU_TIMER5_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&ipu_clkctrl DRA7_IPU_TIMER5_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@22000 {			/* 0x48822000, ap 7 24.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer6";
 			reg = <0x22000 0x4>,
 			      <0x22010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3374,15 +3367,14 @@
 			timer6: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&ipu_clkctrl DRA7_IPU_TIMER6_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&ipu_clkctrl DRA7_IPU_TIMER6_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@24000 {			/* 0x48824000, ap 9 26.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer7";
 			reg = <0x24000 0x4>,
 			      <0x24010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3402,15 +3394,14 @@
 			timer7: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&ipu_clkctrl DRA7_IPU_TIMER7_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&ipu_clkctrl DRA7_IPU_TIMER7_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@26000 {			/* 0x48826000, ap 11 0c.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer8";
 			reg = <0x26000 0x4>,
 			      <0x26010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3430,15 +3421,14 @@
 			timer8: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&ipu_clkctrl DRA7_IPU_TIMER8_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&ipu_clkctrl DRA7_IPU_TIMER8_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@28000 {			/* 0x48828000, ap 13 16.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer13";
 			reg = <0x28000 0x4>,
 			      <0x28010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3458,15 +3448,15 @@
 			timer13: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER13_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER13_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
 		target-module@2a000 {			/* 0x4882a000, ap 15 10.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer14";
 			reg = <0x2a000 0x4>,
 			      <0x2a010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3486,15 +3476,14 @@
 			timer14: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER14_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER14_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
-
-		target-module@2c000 {			/* 0x4882c000, ap 17 02.0 */
+		timer15_target: target-module@2c000 {	/* 0x4882c000, ap 17 02.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer15";
 			reg = <0x2c000 0x4>,
 			      <0x2c010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3514,15 +3503,15 @@
 			timer15: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
-		target-module@2e000 {			/* 0x4882e000, ap 19 14.0 */
+		timer16_target: target-module@2e000 {	/* 0x4882e000, ap 19 14.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer16";
 			reg = <0x2e000 0x4>,
 			      <0x2e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -3542,15 +3531,15 @@
 			timer16: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>, <&timer_sys_clk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
 		rtctarget: target-module@38000 {			/* 0x48838000, ap 29 12.0 */
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
-			ti,hwmods = "rtcss";
 			reg = <0x38074 0x4>,
 			      <0x38078 0x4>;
 			reg-names = "rev", "sysc";
@@ -3994,7 +3983,6 @@
 
 		target-module@80000 {			/* 0x48880000, ap 83 0e.1 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss1";
 			reg = <0x80000 0x4>,
 			      <0x80010 0x4>;
 			reg-names = "rev", "sysc";
@@ -4044,7 +4032,6 @@
 
 		target-module@c0000 {			/* 0x488c0000, ap 79 06.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss2";
 			reg = <0xc0000 0x4>,
 			      <0xc0010 0x4>;
 			reg-names = "rev", "sysc";
@@ -4095,7 +4082,6 @@
 
 		usb3_tm: target-module@100000 {		/* 0x48900000, ap 85 04.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss3";
 			reg = <0x100000 0x4>,
 			      <0x100010 0x4>;
 			reg-names = "rev", "sysc";
@@ -4142,65 +4128,98 @@
 			};
 		};
 
-		usb4_tm: target-module@140000 {		/* 0x48940000, ap 75 3c.0 */
+		target-module@170000 {			/* 0x48970000, ap 21 0a.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss4";
-			reg = <0x140000 0x4>,
-			      <0x140010 0x4>;
-			reg-names = "rev", "sysc";
-			ti,sysc-mask = <SYSC_OMAP4_DMADISABLE>;
+			reg = <0x170010 0x4>;
+			reg-names = "sysc";
 			ti,sysc-midle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
+					<SYSC_IDLE_SMART>;
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
-			/* Domains (P, C): l3init_pwrdm, l3init_clkdm */
-			clocks = <&l3init_clkctrl DRA7_L3INIT_USB_OTG_SS4_CLKCTRL 0>;
+					<SYSC_IDLE_SMART>;
+			clocks = <&cam_clkctrl DRA7_CAM_VIP1_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <0x0 0x140000 0x20000>;
-		};
-
-		target-module@170000 {			/* 0x48970000, ap 21 0a.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
 			ranges = <0x0 0x170000 0x10000>;
+			status = "disabled";
 		};
 
 		target-module@190000 {			/* 0x48990000, ap 23 2e.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x190010 0x4>;
+			reg-names = "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&cam_clkctrl DRA7_CAM_VIP2_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x190000 0x10000>;
+			status = "disabled";
 		};
 
 		target-module@1b0000 {			/* 0x489b0000, ap 25 34.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x1b0000 0x4>,
+			      <0x1b0010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&cam_clkctrl DRA7_CAM_VIP3_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x1b0000 0x10000>;
+			status = "disabled";
 		};
 
-		target-module@1d0000 {			/* 0x489d0000, ap 27 30.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+		target-module@1d0010 {			/* 0x489d0000, ap 27 30.0 */
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x1d0010 0x4>;
+			reg-names = "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			power-domains = <&prm_vpe>;
+			clocks = <&vpe_clkctrl DRA7_VPE_VPE_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x1d0000 0x10000>;
+
+			vpe: vpe@0 {
+				compatible = "ti,dra7-vpe";
+				reg = <0x0000 0x120>,
+				      <0x0700 0x80>,
+				      <0x5700 0x18>,
+				      <0xd000 0x400>;
+				reg-names = "vpe_top",
+					    "sc",
+					    "csc",
+					    "vpdma";
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+			};
 		};
 	};
 };
 
 &l4_wkup {						/* 0x4ae00000 */
-	compatible = "ti,dra7-l4-wkup", "simple-bus";
+	compatible = "ti,dra7-l4-wkup", "simple-pm-bus";
+	power-domains = <&prm_wkupaon>;
+	clocks = <&wkupaon_clkctrl DRA7_WKUPAON_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4ae00000 0x800>,
 	      <0x4ae00800 0x800>,
 	      <0x4ae01000 0x1000>;
@@ -4213,7 +4232,7 @@
 		 <0x00030000 0x4ae30000 0x010000>;	/* segment 3 */
 
 	segment@0 {					/* 0x4ae00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -4228,7 +4247,6 @@
 
 		target-module@4000 {			/* 0x4ae04000, ap 15 40.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "counter_32k";
 			reg = <0x4000 0x4>,
 			      <0x4010 0x4>;
 			reg-names = "rev", "sysc";
@@ -4291,7 +4309,7 @@
 	};
 
 	segment@10000 {					/* 0x4ae10000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00010000 0x001000>,	/* ap 5 */
@@ -4363,9 +4381,8 @@
 			};
 		};
 
-		target-module@8000 {			/* 0x4ae18000, ap 9 30.0 */
+		timer1_target: target-module@8000 {	/* 0x4ae18000, ap 9 30.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer1";
 			reg = <0x8000 0x4>,
 			      <0x8010 0x4>;
 			reg-names = "rev", "sysc";
@@ -4402,7 +4419,7 @@
 	};
 
 	segment@20000 {					/* 0x4ae20000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00006000 0x00026000 0x001000>,	/* ap 13 */
@@ -4422,7 +4439,6 @@
 
 		target-module@0 {			/* 0x4ae20000, ap 19 08.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer12";
 			reg = <0x0 0x4>,
 			      <0x10 0x4>;
 			reg-names = "rev", "sysc";
@@ -4491,7 +4507,7 @@
 			ranges = <0x0 0xb000 0x1000>;
 
 			uart10: serial@0 {
-				compatible = "ti,dra742-uart", "ti,omap4-uart";
+				compatible = "ti,dra742-uart";
 				reg = <0x0 0x100>;
 				interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 				clock-frequency = <48000000>;
@@ -4509,7 +4525,7 @@
 	};
 
 	segment@30000 {					/* 0x4ae30000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0000c000 0x0003c000 0x002000>,	/* ap 30 */
diff --git a/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi b/arch/arm/boot/dts/ti/omap/dra7-mmc-iodelay.dtsi
index aa0947266526..cb1a682c26cd 100644
--- a/arch/arm/boot/dts/dra7-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7-mmc-iodelay.dtsi
@@ -6,7 +6,7 @@
  */
 
 &dra7_pmx_core {
-	mmc1_pins_default_no_clk_pu: mmc1_pins_default_no_clk_pu {
+	mmc1_pins_default_no_clk_pu: mmc1-default-no-clk-pu-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
diff --git a/arch/arm/boot/dts/ti/omap/dra7.dtsi b/arch/arm/boot/dts/ti/omap/dra7.dtsi
new file mode 100644
index 000000000000..6509c742fb58
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra7.dtsi
@@ -0,0 +1,1361 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Based on "omap4.dtsi"
+ */
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/clock/dra7.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/dra.h>
+#include <dt-bindings/clock/dra7.h>
+
+#define MAX_SOURCES 400
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	compatible = "ti,dra7xx";
+	interrupt-parent = <&crossbar_mpu>;
+	chosen { };
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+		serial6 = &uart7;
+		serial7 = &uart8;
+		serial8 = &uart9;
+		serial9 = &uart10;
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
+		d_can0 = &dcan1;
+		d_can1 = &dcan2;
+		spi0 = &qspi;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		status = "disabled";	/* See ARM architected timer wrap erratum i940 */
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&gic>;
+	};
+
+	gic: interrupt-controller@48211000 {
+		compatible = "arm,cortex-a15-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x0 0x48211000 0x0 0x1000>,
+		      <0x0 0x48212000 0x0 0x2000>,
+		      <0x0 0x48214000 0x0 0x2000>,
+		      <0x0 0x48216000 0x0 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-parent = <&gic>;
+	};
+
+	wakeupgen: interrupt-controller@48281000 {
+		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x0 0x48281000 0x0 0x1000>;
+		interrupt-parent = <&gic>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+
+			operating-points-v2 = <&cpu0_opp_table>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
+			/* cooling options */
+			#cooling-cells = <2>; /* min followed by max */
+
+			vbb-supply = <&abb_mpu>;
+		};
+	};
+
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		syscon = <&scm_wkup>;
+
+		opp-1000000000 {
+			/* OPP NOM */
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1060000 850000 1150000>,
+					<1060000 850000 1150000>;
+			opp-supported-hw = <0xFF 0x01>;
+			opp-suspend;
+		};
+
+		opp-1176000000 {
+			/* OPP OD */
+			opp-hz = /bits/ 64 <1176000000>;
+			opp-microvolt = <1160000 885000 1160000>,
+					<1160000 885000 1160000>;
+
+			opp-supported-hw = <0xFF 0x02>;
+		};
+
+		opp-1500000000 {
+			/* OPP High */
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <1210000 950000 1250000>,
+					<1210000 950000 1250000>;
+			opp-supported-hw = <0xFF 0x04>;
+		};
+	};
+
+	/*
+	 * XXX: Use a flat representation of the SOC interconnect.
+	 * The real OMAP interconnect network is quite complex.
+	 * Since it will not bring real advantage to represent that in DT for
+	 * the moment, just use a fake OCP bus entry to represent the whole bus
+	 * hierarchy.
+	 */
+	ocp: ocp {
+		compatible = "simple-pm-bus";
+		power-domains = <&prm_core>;
+		clocks = <&l3main1_clkctrl DRA7_L3MAIN1_L3_MAIN_1_CLKCTRL 0>,
+			 <&l3instr_clkctrl DRA7_L3INSTR_L3_MAIN_2_CLKCTRL 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0xc0000000>;
+		dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>;
+
+		l3-noc@44000000 {
+			compatible = "ti,dra7-l3-noc";
+			reg = <0x44000000 0x1000000>,
+			      <0x45000000 0x1000>;
+			interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					      <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		l4_cfg: interconnect@4a000000 {
+		};
+		l4_wkup: interconnect@4ae00000 {
+		};
+		l4_per1: interconnect@48000000 {
+		};
+
+		target-module@48210000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			power-domains = <&prm_mpu>;
+			clocks = <&mpu_clkctrl DRA7_MPU_MPU_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48210000 0x1f0000>;
+
+			mpu {
+				compatible = "ti,omap5-mpu";
+			};
+		};
+
+		l4_per2: interconnect@48400000 {
+		};
+		l4_per3: interconnect@48800000 {
+		};
+
+		/*
+		 * Register access seems to have complex dependencies and also
+		 * seems to need an enabled phy. See the TRM chapter for "Table
+		 * 26-678. Main Sequence PCIe Controller Global Initialization"
+		 * and also dra7xx_pcie_probe().
+		 */
+		axi0: target-module@51000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			power-domains = <&prm_l3init>;
+			resets = <&prm_l3init 0>;
+			reset-names = "rstctrl";
+			clocks = <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 0>,
+				 <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 9>,
+				 <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 10>;
+			clock-names = "fck", "phy-clk", "phy-clk-div";
+			#size-cells = <1>;
+			#address-cells = <1>;
+			ranges = <0x51000000 0x51000000 0x3000>,
+				 <0x20000000 0x20000000 0x10000000>;
+			dma-ranges;
+			/**
+			 * To enable PCI endpoint mode, disable the pcie1_rc
+			 * node and enable pcie1_ep mode.
+			 */
+			pcie1_rc: pcie@51000000 {
+				reg = <0x51000000 0x2000>,
+				      <0x51002000 0x14c>,
+				      <0x20001000 0x2000>;
+				reg-names = "rc_dbics", "ti_conf", "config";
+				interrupts = <0 232 0x4>, <0 233 0x4>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
+				ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>,
+					 <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>;
+				bus-range = <0x00 0xff>;
+				#interrupt-cells = <1>;
+				num-lanes = <1>;
+				linux,pci-domain = <0>;
+				phys = <&pcie1_phy>;
+				phy-names = "pcie-phy0";
+				ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 1>,
+						<0 0 0 2 &pcie1_intc 2>,
+						<0 0 0 3 &pcie1_intc 3>,
+						<0 0 0 4 &pcie1_intc 4>;
+				ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
+				status = "disabled";
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#address-cells = <0>;
+					#interrupt-cells = <1>;
+				};
+			};
+
+			pcie1_ep: pcie_ep@51000000 {
+				reg = <0x51000000 0x28>,
+				      <0x51002000 0x14c>,
+				      <0x51001000 0x28>,
+				      <0x20001000 0x10000000>;
+				reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
+				interrupts = <0 232 0x4>;
+				num-lanes = <1>;
+				num-ib-windows = <4>;
+				num-ob-windows = <16>;
+				phys = <&pcie1_phy>;
+				phy-names = "pcie-phy0";
+				ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
+				ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
+				status = "disabled";
+			};
+		};
+
+		/*
+		 * Register access seems to have complex dependencies and also
+		 * seems to need an enabled phy. See the TRM chapter for "Table
+		 * 26-678. Main Sequence PCIe Controller Global Initialization"
+		 * and also dra7xx_pcie_probe().
+		 */
+		axi1: target-module@51800000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			clocks = <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 0>,
+				 <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 9>,
+				 <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 10>;
+			clock-names = "fck", "phy-clk", "phy-clk-div";
+			power-domains = <&prm_l3init>;
+			resets = <&prm_l3init 1>;
+			reset-names = "rstctrl";
+			#size-cells = <1>;
+			#address-cells = <1>;
+			ranges = <0x51800000 0x51800000 0x3000>,
+				 <0x30000000 0x30000000 0x10000000>;
+			dma-ranges;
+			status = "disabled";
+			pcie2_rc: pcie@51800000 {
+				reg = <0x51800000 0x2000>,
+				      <0x51802000 0x14c>,
+				      <0x30001000 0x2000>;
+				reg-names = "rc_dbics", "ti_conf", "config";
+				interrupts = <0 355 0x4>, <0 356 0x4>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
+				ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>,
+					 <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>;
+				bus-range = <0x00 0xff>;
+				#interrupt-cells = <1>;
+				num-lanes = <1>;
+				linux,pci-domain = <1>;
+				phys = <&pcie2_phy>;
+				phy-names = "pcie-phy0";
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 1>,
+						<0 0 0 2 &pcie2_intc 2>,
+						<0 0 0 3 &pcie2_intc 3>,
+						<0 0 0 4 &pcie2_intc 4>;
+				ti,syscon-unaligned-access = <&scm_conf1 0x14 2>;
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#address-cells = <0>;
+					#interrupt-cells = <1>;
+				};
+			};
+		};
+
+		ocmcram1: ocmcram@40300000 {
+			compatible = "mmio-sram";
+			reg = <0x40300000 0x80000>;
+			ranges = <0x0 0x40300000 0x80000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/*
+			 * This is a placeholder for an optional reserved
+			 * region for use by secure software. The size
+			 * of this region is not known until runtime so it
+			 * is set as zero to either be updated to reserve
+			 * space or left unchanged to leave all SRAM for use.
+			 * On HS parts that that require the reserved region
+			 * either the bootloader can update the size to
+			 * the required amount or the node can be overridden
+			 * from the board dts file for the secure platform.
+			 */
+			sram-hs@0 {
+				compatible = "ti,secure-ram";
+				reg = <0x0 0x0>;
+			};
+		};
+
+		/*
+		 * NOTE: ocmcram2 and ocmcram3 are not available on all
+		 * DRA7xx and AM57xx variants. Confirm availability in
+		 * the data manual for the exact part number in use
+		 * before enabling these nodes in the board dts file.
+		 */
+		ocmcram2: ocmcram@40400000 {
+			status = "disabled";
+			compatible = "mmio-sram";
+			reg = <0x40400000 0x100000>;
+			ranges = <0x0 0x40400000 0x100000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
+		ocmcram3: ocmcram@40500000 {
+			status = "disabled";
+			compatible = "mmio-sram";
+			reg = <0x40500000 0x100000>;
+			ranges = <0x0 0x40500000 0x100000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
+		bandgap: bandgap@4a0021e0 {
+			reg = <0x4a0021e0 0xc
+				0x4a00232c 0xc
+				0x4a002380 0x2c
+				0x4a0023C0 0x3c
+				0x4a002564 0x8
+				0x4a002574 0x50>;
+				compatible = "ti,dra752-bandgap";
+				interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+				#thermal-sensor-cells = <1>;
+		};
+
+		dsp1_system: dsp_system@40d00000 {
+			compatible = "syscon";
+			reg = <0x40d00000 0x100>;
+		};
+
+		dra7_iodelay_core: padconf@4844a000 {
+			compatible = "ti,dra7-iodelay";
+			reg = <0x4844a000 0x0d1c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pinctrl-cells = <2>;
+		};
+
+		target-module@43300000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x43300000 0x4>,
+			      <0x43300010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPCC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x43300000 0x100000>;
+
+			edma: dma@0 {
+				compatible = "ti,edma3-tpcc";
+				reg = <0 0x100000>;
+				reg-names = "edma3_cc";
+				interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_ccint", "edma3_mperr",
+						  "edma3_ccerrint";
+				dma-requests = <64>;
+				#dma-cells = <2>;
+
+				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 0>;
+
+				/*
+				* memcpy is disabled, can be enabled with:
+				* ti,edma-memcpy-channels = <20 21>;
+				* for example. Note that these channels need to be
+				* masked in the xbar as well.
+				*/
+			};
+		};
+
+		target-module@43400000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x43400000 0x4>,
+			      <0x43400010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC0_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x43400000 0x100000>;
+
+			edma_tptc0: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@43500000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x43500000 0x4>,
+			      <0x43500010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x43500000 0x100000>;
+
+			edma_tptc1: dma@0 {
+				compatible = "ti,edma3-tptc";
+				reg = <0 0x100000>;
+				interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "edma3_tcerrint";
+			};
+		};
+
+		target-module@4e000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4e000000 0x4>,
+			      <0x4e000010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ranges = <0x0 0x4e000000 0x2000000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			dmm@0 {
+				compatible = "ti,omap5-dmm";
+				reg = <0 0x800>;
+				interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		ipu1: ipu@58820000 {
+			compatible = "ti,dra7-ipu";
+			reg = <0x58820000 0x10000>;
+			reg-names = "l2ram";
+			iommus = <&mmu_ipu1>;
+			status = "disabled";
+			resets = <&prm_ipu 0>, <&prm_ipu 1>;
+			clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>;
+			firmware-name = "dra7-ipu1-fw.xem4";
+		};
+
+		ipu2: ipu@55020000 {
+			compatible = "ti,dra7-ipu";
+			reg = <0x55020000 0x10000>;
+			reg-names = "l2ram";
+			iommus = <&mmu_ipu2>;
+			status = "disabled";
+			resets = <&prm_core 0>, <&prm_core 1>;
+			clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>;
+			firmware-name = "dra7-ipu2-fw.xem4";
+		};
+
+		dsp1: dsp@40800000 {
+			compatible = "ti,dra7-dsp";
+			reg = <0x40800000 0x48000>,
+			      <0x40e00000 0x8000>,
+			      <0x40f00000 0x8000>;
+			reg-names = "l2ram", "l1pram", "l1dram";
+			ti,bootreg = <&scm_conf 0x55c 10>;
+			iommus = <&mmu0_dsp1>, <&mmu1_dsp1>;
+			status = "disabled";
+			resets = <&prm_dsp1 0>;
+			clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
+			firmware-name = "dra7-dsp1-fw.xe66";
+		};
+
+		target-module@40d01000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x40d01000 0x4>,
+			      <0x40d01010 0x4>,
+			      <0x40d01014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_dsp1 1>;
+			reset-names = "rstctrl";
+			ranges = <0x0 0x40d01000 0x1000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			mmu0_dsp1: mmu@0 {
+				compatible = "ti,dra7-dsp-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,syscon-mmuconfig = <&dsp1_system 0x0>;
+			};
+		};
+
+		target-module@40d02000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x40d02000 0x4>,
+			      <0x40d02010 0x4>,
+			      <0x40d02014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_dsp1 1>;
+			reset-names = "rstctrl";
+			ranges = <0x0 0x40d02000 0x1000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			mmu1_dsp1: mmu@0 {
+				compatible = "ti,dra7-dsp-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,syscon-mmuconfig = <&dsp1_system 0x1>;
+			};
+		};
+
+		target-module@58882000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x58882000 0x4>,
+			      <0x58882010 0x4>,
+			      <0x58882014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_ipu 2>;
+			reset-names = "rstctrl";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x58882000 0x100>;
+
+			mmu_ipu1: mmu@0 {
+				compatible = "ti,dra7-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,iommu-bus-err-back;
+			};
+		};
+
+		target-module@55082000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x55082000 0x4>,
+			      <0x55082010 0x4>,
+			      <0x55082014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_core 2>;
+			reset-names = "rstctrl";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x55082000 0x100>;
+
+			mmu_ipu2: mmu@0 {
+				compatible = "ti,dra7-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,iommu-bus-err-back;
+			};
+		};
+
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+			      <0x4ae06014 0x4>, <0x4a003b20 0xc>,
+			      <0x4ae0c158 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x80>;
+			/* LDOVBBMPU_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBMPU_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1060000		0	0x0	0 0x02000000 0x01F00000
+			1160000		0	0x4	0 0x02000000 0x01F00000
+			1210000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_ivahd: regulator-abb-ivahd {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_ivahd";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+			      <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
+			      <0x4a002470 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x40000000>;
+			/* LDOVBBIVA_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBIVA_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1055000		0	0x0	0 0x02000000 0x01F00000
+			1150000		0	0x4	0 0x02000000 0x01F00000
+			1250000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_dspeve: regulator-abb-dspeve {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_dspeve";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+			      <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
+			      <0x4a00246c 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x20000000>;
+			/* LDOVBBDSPEVE_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBDSPEVE_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1055000		0	0x0	0 0x02000000 0x01F00000
+			1150000		0	0x4	0 0x02000000 0x01F00000
+			1250000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_gpu: regulator-abb-gpu {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_gpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+			      <0x4ae06010 0x4>, <0x4a003b08 0xc>,
+			      <0x4ae0c154 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x10000000>;
+			/* LDOVBBGPU_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBGPU_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1090000		0	0x0	0 0x02000000 0x01F00000
+			1210000		0	0x4	0 0x02000000 0x01F00000
+			1280000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		target-module@4b300000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x4b300000 0x4>,
+			      <0x4b300010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b300000 0x1000>,
+				 <0x5c000000 0x5c000000 0x4000000>;
+
+			qspi: spi@0 {
+				compatible = "ti,dra7xxx-qspi";
+				reg = <0 0x100>,
+				      <0x5c000000 0x4000000>;
+				reg-names = "qspi_base", "qspi_mmap";
+				syscon-chipselects = <&scm_conf 0x558>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>;
+				clock-names = "fck";
+				num-cs = <4>;
+				interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		/* OCP2SCP1 */
+		/* IRQ for DWC3_3 and DWC3_4 need IRQ crossbar */
+
+		target-module@50000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x50000000 4>,
+			      <0x50000010 4>,
+			      <0x50000014 4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_GPMC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
+				 <0x00000000 0x00000000 0x40000000>; /* data */
+
+			gpmc: gpmc@50000000 {
+				compatible = "ti,am3352-gpmc";
+				reg = <0x50000000 0x37c>;      /* device IO registers */
+				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma_xbar 4 0>;
+				dma-names = "rxtx";
+				gpmc,num-cs = <8>;
+				gpmc,num-waitpins = <2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		target-module@56000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5600fe00 0x4>,
+			      <0x5600fe10 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&gpu_clkctrl DRA7_GPU_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x56000000 0x2000000>;
+		};
+
+		crossbar_mpu: crossbar@4a002a48 {
+			compatible = "ti,irq-crossbar";
+			reg = <0x4a002a48 0x130>;
+			interrupt-controller;
+			interrupt-parent = <&wakeupgen>;
+			#interrupt-cells = <3>;
+			ti,max-irqs = <160>;
+			ti,max-crossbar-sources = <MAX_SOURCES>;
+			ti,reg-size = <2>;
+			ti,irqs-reserved = <0 1 2 3 5 6 131 132>;
+			ti,irqs-skip = <10 133 139 140>;
+			ti,irqs-safe-map = <0>;
+		};
+
+		target-module@58000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x58000000 4>,
+			      <0x58000014 4>;
+			reg-names = "rev", "syss";
+			ti,syss-mask = <1>;
+			clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 0>,
+				 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
+				 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>,
+				 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 11>;
+			clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x58000000 0x800000>;
+
+			dss: dss@0 {
+				compatible = "ti,dra7-dss";
+				/* 'reg' defined in dra72x.dtsi and dra74x.dtsi */
+				/* 'clocks' defined in dra72x.dtsi and dra74x.dtsi */
+				status = "disabled";
+				/* CTRL_CORE_DSS_PLL_CONTROL */
+				syscon-pll-ctrl = <&scm_conf 0x538>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0 0x800000>;
+
+				target-module@1000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x1000 0x4>,
+					      <0x1010 0x4>,
+					      <0x1014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-midle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x1000 0x1000>;
+
+					dispc@0 {
+						compatible = "ti,dra7-dispc";
+						reg = <0 0x1000>;
+						interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+						clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
+						clock-names = "fck";
+						/* CTRL_CORE_SMA_SW_1 */
+						syscon-pol = <&scm_conf 0x534>;
+					};
+				};
+
+				target-module@40000 {
+					compatible = "ti,sysc-omap4", "ti,sysc";
+					reg = <0x40000 0x4>,
+					      <0x40010 0x4>;
+					reg-names = "rev", "sysc";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>,
+							<SYSC_IDLE_SMART_WKUP>;
+					ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
+					clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
+						 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
+					clock-names = "fck", "dss_clk";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x40000 0x40000>;
+
+					hdmi: encoder@0 {
+						compatible = "ti,dra7-hdmi";
+						reg = <0 0x200>,
+						      <0x200 0x80>,
+						      <0x300 0x80>,
+						      <0x20000 0x19000>;
+						reg-names = "wp", "pll", "phy", "core";
+						interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
+							 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+						dmas = <&sdma_xbar 76>;
+						dma-names = "audio_tx";
+					};
+				};
+			};
+		};
+
+		target-module@59000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x59000020 0x4>;
+			reg-names = "rev";
+			clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x59000000 0x1000>;
+
+			bb2d: gpu@0 {
+				compatible = "vivante,gc";
+				reg = <0x0 0x700>;
+				interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>;
+				clock-names = "core";
+			};
+		};
+
+		aes1_target: target-module@4b500000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4b500080 0x4>,
+			      <0x4b500084 0x4>,
+			      <0x4b500088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl DRA7_L4SEC_AES1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b500000 0x1000>;
+
+			aes1: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma_xbar 111 0>, <&edma_xbar 110 0>;
+				dma-names = "tx", "rx";
+				clocks = <&l3_iclk_div>;
+				clock-names = "fck";
+			};
+		};
+
+		aes2_target: target-module@4b700000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4b700080 0x4>,
+			      <0x4b700084 0x4>,
+			      <0x4b700088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl DRA7_L4SEC_AES2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b700000 0x1000>;
+
+			aes2: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma_xbar 114 0>, <&edma_xbar 113 0>;
+				dma-names = "tx", "rx";
+				clocks = <&l3_iclk_div>;
+				clock-names = "fck";
+			};
+		};
+
+		sham1_target: target-module@4b101000 {
+			compatible = "ti,sysc-omap3-sham", "ti,sysc";
+			reg = <0x4b101100 0x4>,
+			      <0x4b101110 0x4>,
+			      <0x4b101114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b101000 0x1000>;
+
+			sham1: sham@0 {
+				compatible = "ti,omap5-sham";
+				reg = <0 0x300>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma_xbar 119 0>;
+				dma-names = "rx";
+				clocks = <&l3_iclk_div>;
+				clock-names = "fck";
+			};
+		};
+
+		sham2_target: target-module@42701000 {
+			compatible = "ti,sysc-omap3-sham", "ti,sysc";
+			reg = <0x42701100 0x4>,
+			      <0x42701110 0x4>,
+			      <0x42701114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x42701000 0x1000>;
+
+			sham2: sham@0 {
+				compatible = "ti,omap5-sham";
+				reg = <0 0x300>;
+				interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&edma_xbar 165 0>;
+				dma-names = "rx";
+				clocks = <&l3_iclk_div>;
+				clock-names = "fck";
+			};
+		};
+
+		iva_hd_target: target-module@5a000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5a05a400 0x4>,
+			      <0x5a05a410 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			power-domains = <&prm_iva>;
+			resets = <&prm_iva 2>;
+			reset-names = "rstctrl";
+			clocks = <&iva_clkctrl DRA7_IVA_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x5a000000 0x5a000000 0x1000000>,
+				 <0x5b000000 0x5b000000 0x1000000>;
+
+			iva {
+				compatible = "ti,ivahd";
+			};
+		};
+
+		opp_supply_mpu: opp-supply@4a003b20 {
+			compatible = "ti,omap5-opp-supply";
+			reg = <0x4a003b20 0xc>;
+			ti,efuse-settings = <
+			/* uV   offset */
+			1060000 0x0
+			1160000 0x4
+			1210000 0x8
+			>;
+			ti,absolute-max-voltage-uv = <1500000>;
+		};
+
+	};
+
+	thermal_zones: thermal-zones {
+		#include "omap4-cpu-thermal.dtsi"
+		#include "omap5-gpu-thermal.dtsi"
+		#include "omap5-core-thermal.dtsi"
+		#include "dra7-dspeve-thermal.dtsi"
+		#include "dra7-iva-thermal.dtsi"
+	};
+
+};
+
+&cpu_thermal {
+	polling-delay = <500>; /* milliseconds */
+	coefficients = <0 2000>;
+};
+
+&gpu_thermal {
+	coefficients = <0 2000>;
+};
+
+&core_thermal {
+	coefficients = <0 2000>;
+};
+
+&dspeve_thermal {
+	coefficients = <0 2000>;
+};
+
+&iva_thermal {
+	coefficients = <0 2000>;
+};
+
+&cpu_crit {
+	temperature = <120000>; /* milli Celsius */
+};
+
+&core_crit {
+	temperature = <120000>; /* milli Celsius */
+};
+
+&gpu_crit {
+	temperature = <120000>; /* milli Celsius */
+};
+
+&dspeve_crit {
+	temperature = <120000>; /* milli Celsius */
+};
+
+&iva_crit {
+	temperature = <120000>; /* milli Celsius */
+};
+
+#include "dra7-l4.dtsi"
+#include "dra7xx-clocks.dtsi"
+
+&prm {
+	prm_mpu: prm@300 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x300 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dsp1: prm@400 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x400 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_ipu: prm@500 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x500 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_coreaon: prm@628 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x628 0xd8>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_core: prm@700 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x700 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_iva: prm@f00 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0xf00 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_cam: prm@1000 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1000 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dss: prm@1100 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1100 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_gpu: prm@1200 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1200 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_l3init: prm@1300 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1300 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_l4per: prm@1400 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1400 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_custefuse: prm@1600 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1600 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_wkupaon: prm@1724 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1724 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dsp2: prm@1b00 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1b00 0x40>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_eve1: prm@1b40 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1b40 0x40>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_eve2: prm@1b80 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1b80 0x40>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_eve3: prm@1bc0 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1bc0 0x40>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_eve4: prm@1c00 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1c00 0x60>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_rtc: prm@1c60 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1c60 0x20>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_vpe: prm@1c80 {
+		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1c80 0x80>;
+		#power-domain-cells = <0>;
+	};
+};
+
+/* Preferred always-on timer for clockevent */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&wkupaon_clkctrl DRA7_WKUPAON_TIMER1_CLKCTRL 24>;
+		assigned-clock-parents = <&sys_32k_ck>;
+	};
+};
+
+/* Local timers, see ARM architected timer wrap erratum i940 */
+&timer15_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>;
+		assigned-clock-parents = <&timer_sys_clk_div>;
+	};
+};
+
+&timer16_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>;
+		assigned-clock-parents = <&timer_sys_clk_div>;
+	};
+};
diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/ti/omap/dra71-evm.dts
index fabeb7704753..f747ac56eb92 100644
--- a/arch/arm/boot/dts/dra71-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dra71-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "dra71x.dtsi"
@@ -17,6 +17,33 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	vpo_sd_1v8_3v3: gpio-regulator-TPS74801 {
 		compatible = "regulator-gpio";
 
@@ -85,6 +112,8 @@
 				regulator-name = "lp8733-ldo0";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 
 			lp8733_ldo1_reg: ldo1 {
@@ -158,7 +187,7 @@
 };
 
 &pcf_hdmi {
-	p0 {
+	hdmi-i2c-disable-hog {
 		/*
 		 * PM_OEn to High: Disable routing I2C3 to PM_I2C
 		 * With this PM_SEL(p3) should not matter
@@ -192,26 +221,26 @@
 	vqmmc-supply = <&evm_1v8_sw>;
 };
 
-&mac {
+&mac_sw {
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
 		     <&pcf_hdmi 9 GPIO_ACTIVE_LOW>,	/* P11 */
 		     <&pcf_hdmi 10 GPIO_ACTIVE_LOW>;	/* P12 */
-	dual_emac;
+	status = "okay";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&dp83867_0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&dp83867_1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	dp83867_0: ethernet-phy@2 {
 		reg = <2>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
@@ -264,9 +293,24 @@
 };
 
 &extcon_usb1 {
-	vbus-gpio = <&pcf_lcd 14 GPIO_ACTIVE_HIGH>;
+	vbus-gpios = <&pcf_lcd 14 GPIO_ACTIVE_HIGH>;
 };
 
 &extcon_usb2 {
-	vbus-gpio = <&pcf_lcd 15 GPIO_ACTIVE_HIGH>;
+	vbus-gpios = <&pcf_lcd 15 GPIO_ACTIVE_HIGH>;
+};
+
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_memory_region>;
+};
+
+&ipu1 {
+	status = "okay";
+	memory-region = <&ipu1_memory_region>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_memory_region>;
 };
diff --git a/arch/arm/boot/dts/dra71x.dtsi b/arch/arm/boot/dts/ti/omap/dra71x.dtsi
index 695a08ed0360..9c270d8f75d5 100644
--- a/arch/arm/boot/dts/dra71x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra71x.dtsi
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -11,7 +11,3 @@
 &rtctarget {
 	status = "disabled";
 };
-
-&usb4_tm {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/ti/omap/dra72-evm-common.dtsi
index 8641a3d7d8ad..f8151c61488e 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra72-evm-common.dtsi
@@ -1,12 +1,13 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
 #include "dra72x.dtsi"
+#include "dra7-ipu-dsp-common.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/clock/ti-dra7-atl.h>
 
 / {
 	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
@@ -95,12 +96,12 @@
 
 	extcon_usb1: extcon_usb1 {
 		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
+		id-gpios = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
 	};
 
 	extcon_usb2: extcon_usb2 {
 		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
+		id-gpios = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
 	};
 
 	hdmi0: connector {
@@ -187,17 +188,23 @@
 		gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	clk_ov5640_fixed: clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
 };
 
 &dra7_pmx_core {
-	dcan1_pins_default: dcan1_pins_default {
+	dcan1_pins_default: dcan1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
 			DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1)	/* wakeup0.dcan1_rx */
 		>;
 	};
 
-	dcan1_pins_sleep: dcan1_pins_sleep {
+	dcan1_pins_sleep: dcan1-sleep-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
 			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
@@ -219,7 +226,7 @@
 	};
 
 	pcf_gpio_21: gpio@21 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x21>;
 		lines-initial-states = <0x1408>;
 		gpio-controller;
@@ -249,7 +256,7 @@
 	clock-frequency = <400000>;
 
 	pcf_hdmi: pcf8575@26 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x26>;
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -261,7 +268,7 @@
 		 */
 		lines-initial-states = <0x0f2b>;
 
-		p1 {
+		hdmi-audio-hog {
 			/* vin6_sel_s0: high: VIN6, low: audio */
 			gpio-hog;
 			gpios = <1 GPIO_ACTIVE_HIGH>;
@@ -269,6 +276,23 @@
 			line-name = "vin6_sel_s0";
 		};
 	};
+
+	ov5640@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+
+		clocks = <&clk_ov5640_fixed>;
+		clock-names = "xclk";
+
+		port {
+			csi2_cam0: endpoint {
+				remote-endpoint = <&csi2_phy0>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
 };
 
 &uart1 {
@@ -332,7 +356,7 @@
 		#size-cells = <1>;
 		partition@0 {
 			label = "NAND.SPL";
-			reg = <0x00000000 0x000020000>;
+			reg = <0x00000000 0x00020000>;
 		};
 		partition@1 {
 			label = "NAND.SPL.backup1";
@@ -438,12 +462,8 @@
 	};
 };
 
-&mac {
-	status = "okay";
-};
-
 &dcan1 {
-	status = "ok";
+	status = "okay";
 	pinctrl-names = "default", "sleep", "active";
 	pinctrl-0 = <&dcan1_pins_sleep>;
 	pinctrl-1 = <&dcan1_pins_sleep>;
@@ -454,7 +474,7 @@
 	status = "okay";
 
 	spi-max-frequency = <76800000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "s25fl256s1";
 		spi-max-frequency = <76800000>;
 		reg = <0>;
@@ -470,7 +490,7 @@
 		 */
 		partition@0 {
 			label = "QSPI.SPL";
-			reg = <0x00000000 0x000010000>;
+			reg = <0x00000000 0x00010000>;
 		};
 		partition@1 {
 			label = "QSPI.SPL.backup1";
@@ -512,11 +532,11 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 
 	port {
 		hdmi_out: endpoint {
@@ -560,23 +580,14 @@
 	rx-num-evt = <32>;
 };
 
-&mailbox5 {
+&pcie1_rc {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
 };
 
-&mailbox6 {
-	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
+&csi2_0 {
+	csi2_phy0: endpoint {
+		remote-endpoint = <&csi2_cam0>;
+		clock-lanes = <0>;
+		data-lanes = <1 2>;
 	};
 };
-
-&pcie1_rc {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/ti/omap/dra72-evm-revc.dts
index 2bb2e8be6276..f242b937f88c 100644
--- a/arch/arm/boot/dts/dra72-evm-revc.dts
+++ b/arch/arm/boot/dts/ti/omap/dra72-evm-revc.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include "dra72-evm-common.dtsi"
 #include "dra72x-mmc-iodelay.dtsi"
@@ -14,6 +14,33 @@
 		reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_cma_pool: ipu2_cma@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_cma_pool: dsp1_cma@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_cma_pool: ipu1_cma@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	evm_1v8_sw: fixedregulator-evm_1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "evm_1v8";
@@ -50,26 +77,26 @@
 	interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
 };
 
-&mac {
+&mac_sw {
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
 		     <&pcf_hdmi 9 GPIO_ACTIVE_LOW>,	/* P11 */
 		     <&pcf_hdmi 10 GPIO_ACTIVE_LOW>;	/* P12 */
-	dual_emac;
+	status = "okay";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&dp83867_0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&dp83867_1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	dp83867_0: ethernet-phy@2 {
 		reg = <2>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
@@ -113,3 +140,18 @@
 	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
 	vmmc-supply = <&evm_1v8_sw>;
 };
+
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_cma_pool>;
+};
+
+&ipu1 {
+	status = "okay";
+	memory-region = <&ipu1_cma_pool>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_cma_pool>;
+};
diff --git a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi b/arch/arm/boot/dts/ti/omap/dra72-evm-tps65917.dtsi
index 5ff9c43ef30b..7b433f549239 100644
--- a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra72-evm-tps65917.dtsi
@@ -1,11 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
  * Integrated Power Management Chip
- * http://www.ti.com/lit/ds/symlink/tps65917-q1.pdf
+ * https://www.ti.com/lit/ds/symlink/tps65917-q1.pdf
  */
 
 &tps65917 {
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/ti/omap/dra72-evm.dts
index 9adb77585ef1..5f62f92eb96c 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dra72-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include "dra72-evm-common.dtsi"
 #include "dra72x-mmc-iodelay.dtsi"
@@ -12,6 +12,33 @@
 		reg = <0x0 0x80000000 0x0 0x40000000>; /* 1024 MB */
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_memory_region: ipu2-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_memory_region: dsp1-memory@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_memory_region: ipu1-memory@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	evm_1v8_sw: fixedregulator-evm_1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "evm_1v8";
@@ -42,17 +69,22 @@
 	interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	ethphy0: ethernet-phy@3 {
 		reg = <3>;
 	};
@@ -78,3 +110,18 @@
 	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev10_conf>;
 	vmmc-supply = <&evm_1v8_sw>;
 };
+
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_memory_region>;
+};
+
+&ipu1 {
+	status = "okay";
+	memory-region = <&ipu1_memory_region>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_memory_region>;
+};
diff --git a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi b/arch/arm/boot/dts/ti/omap/dra72x-mmc-iodelay.dtsi
index edad87c4292c..d006f1dfdeb5 100644
--- a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra72x-mmc-iodelay.dtsi
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * MMC IOdelay values for TI's DRA72x, DRA71x and AM571x SoCs.
  *
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -40,7 +32,7 @@
  */
 
 &dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
+	mmc1_pins_default: mmc1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
@@ -51,7 +43,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr12: mmc1_pins_sdr12 {
+	mmc1_pins_sdr12: mmc1-sdr12-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -62,7 +54,7 @@
 		>;
 	};
 
-	mmc1_pins_hs: mmc1_pins_hs {
+	mmc1_pins_hs: mmc1-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
@@ -73,7 +65,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr25: mmc1_pins_sdr25 {
+	mmc1_pins_sdr25: mmc1-sdr25-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -84,7 +76,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+	mmc1_pins_sdr50: mmc1-sdr50-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -95,7 +87,7 @@
 		>;
 	};
 
-	mmc1_pins_ddr50_rev10: mmc1_pins_ddr50_rev10 {
+	mmc1_pins_ddr50_rev10: mmc1-ddr50-rev10-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
@@ -106,7 +98,7 @@
 		>;
 	};
 
-	mmc1_pins_ddr50_rev20: mmc1_pins_ddr50_rev20 {
+	mmc1_pins_ddr50_rev20: mmc1-ddr50-rev20-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -117,7 +109,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr104: mmc1_pins_sdr104 {
+	mmc1_pins_sdr104: mmc1-sdr104-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -128,7 +120,7 @@
 		>;
 	};
 
-	mmc2_pins_default: mmc2_pins_default {
+	mmc2_pins_default: mmc2-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -143,7 +135,7 @@
 		>;
 	};
 
-	mmc2_pins_hs: mmc2_pins_hs {
+	mmc2_pins_hs: mmc2-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -158,7 +150,7 @@
 		>;
 	};
 
-	mmc2_pins_ddr_rev10: mmc2_pins_ddr_rev10 {
+	mmc2_pins_ddr_rev10: mmc2-ddr-rev10-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a19.mmc2_dat4 */
 			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a20.mmc2_dat5 */
@@ -173,7 +165,7 @@
 		>;
 	};
 
-	mmc2_pins_ddr_rev20: mmc2_pins_ddr_rev20 {
+	mmc2_pins_ddr_rev20: mmc2-ddr-rev20-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -188,7 +180,7 @@
 		>;
 	};
 
-	mmc2_pins_hs200: mmc2_pins_hs200 {
+	mmc2_pins_hs200: mmc2-hs200-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -203,7 +195,7 @@
 		>;
 	};
 
-	mmc4_pins_default: mmc4_pins_default {
+	mmc4_pins_default: mmc4-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
 			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
diff --git a/arch/arm/boot/dts/ti/omap/dra72x.dtsi b/arch/arm/boot/dts/ti/omap/dra72x.dtsi
new file mode 100644
index 000000000000..90617261373c
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra72x.dtsi
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Based on "omap4.dtsi"
+ */
+
+#include "dra7.dtsi"
+
+/ {
+	compatible = "ti,dra722", "ti,dra72", "ti,dra7";
+
+	aliases {
+		rproc0 = &ipu1;
+		rproc1 = &ipu2;
+		rproc2 = &dsp1;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupt-parent = <&wakeupgen>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&l4_per2 {
+	target-module@5b000 {			/* 0x4845b000, ap 59 46.0 */
+		compatible = "ti,sysc-omap4", "ti,sysc";
+		reg = <0x5b000 0x4>,
+		      <0x5b010 0x4>;
+		reg-names = "rev", "sysc";
+		ti,sysc-midle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>;
+		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>;
+		clocks = <&cam_clkctrl DRA7_CAM_VIP2_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x5b000 0x1000>;
+
+		cal: cal@0 {
+			compatible = "ti,dra72-cal";
+			reg = <0x0000 0x400>,
+			      <0x0800 0x40>,
+			      <0x0900 0x40>;
+			reg-names = "cal_top",
+				    "cal_rx_core0",
+				    "cal_rx_core1";
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			ti,camerrx-control = <&scm_conf 0xE94>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				csi2_0: port@0 {
+					reg = <0>;
+				};
+				csi2_1: port@1 {
+					reg = <1>;
+				};
+			};
+		};
+	};
+};
+
+&dss {
+	reg = <0 0x80>,
+	      <0x4054 0x4>,
+	      <0x4300 0x20>;
+	reg-names = "dss", "pll1_clkctrl", "pll1";
+
+	clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>,
+		 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 12>;
+	clock-names = "fck", "video1_clk";
+};
+
+&mailbox5 {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
+		ti,mbox-tx = <6 2 2>;
+		ti,mbox-rx = <4 2 2>;
+		status = "disabled";
+	};
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
+		ti,mbox-tx = <5 2 2>;
+		ti,mbox-rx = <1 2 2>;
+		status = "disabled";
+	};
+};
+
+&mailbox6 {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
+		ti,mbox-tx = <6 2 2>;
+		ti,mbox-rx = <4 2 2>;
+		status = "disabled";
+	};
+};
+
+&pcie1_rc {
+	compatible = "ti,dra726-pcie-rc", "ti,dra7-pcie";
+};
+
+&pcie1_ep {
+	compatible = "ti,dra726-pcie-ep", "ti,dra7-pcie-ep";
+};
+
+&pcie2_rc {
+	compatible = "ti,dra726-pcie-rc", "ti,dra7-pcie";
+};
diff --git a/arch/arm/boot/dts/ti/omap/dra74-ipu-dsp-common.dtsi b/arch/arm/boot/dts/ti/omap/dra74-ipu-dsp-common.dtsi
new file mode 100644
index 000000000000..3256631510c5
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra74-ipu-dsp-common.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common IPU and DSP data for TI DRA74x/DRA76x/AM572x/AM574x platforms
+ */
+
+#include "dra7-ipu-dsp-common.dtsi"
+
+&mailbox6 {
+	mbox_dsp2_ipc3x: mbox-dsp2-ipc3x {
+		status = "okay";
+	};
+};
+
+&dsp2 {
+	mboxes = <&mailbox6 &mbox_dsp2_ipc3x>;
+	ti,timers = <&timer6>;
+	ti,watchdog-timers = <&timer13>;
+};
diff --git a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi b/arch/arm/boot/dts/ti/omap/dra74x-mmc-iodelay.dtsi
index 214b9e6de2c3..e2fdb0702f5c 100644
--- a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra74x-mmc-iodelay.dtsi
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * MMC IOdelay values for TI's DRA74x, DRA75x and AM572x SoCs.
  *
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 /*
@@ -38,7 +30,7 @@
  */
 
 &dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
+	mmc1_pins_default: mmc1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
@@ -49,7 +41,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr12: mmc1_pins_sdr12 {
+	mmc1_pins_sdr12: mmc1-sdr12-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -60,7 +52,7 @@
 		>;
 	};
 
-	mmc1_pins_hs: mmc1_pins_hs {
+	mmc1_pins_hs: mmc1-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_cmd.cmd */
@@ -71,7 +63,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr25: mmc1_pins_sdr25 {
+	mmc1_pins_sdr25: mmc1-sdr25-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -82,7 +74,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+	mmc1_pins_sdr50: mmc1-sdr50-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -93,7 +85,7 @@
 		>;
 	};
 
-	mmc1_pins_ddr50: mmc1_pins_ddr50 {
+	mmc1_pins_ddr50: mmc1-ddr50-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -104,7 +96,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr104: mmc1_pins_sdr104 {
+	mmc1_pins_sdr104: mmc1-sdr104-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -115,7 +107,7 @@
 		>;
 	};
 
-	mmc2_pins_default: mmc2_pins_default {
+	mmc2_pins_default: mmc2-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -130,7 +122,7 @@
 		>;
 	};
 
-	mmc2_pins_hs: mmc2_pins_hs {
+	mmc2_pins_hs: mmc2-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -145,7 +137,7 @@
 		>;
 	};
 
-	mmc2_pins_ddr_3_3v_rev11: mmc2_pins_ddr_3_3v_rev11 {
+	mmc2_pins_ddr_3_3v_rev11: mmc2-ddr-3-3v-rev11-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -160,7 +152,7 @@
 		>;
 	};
 
-	mmc2_pins_ddr_1_8v_rev11: mmc2_pins_ddr_1_8v_rev11 {
+	mmc2_pins_ddr_1_8v_rev11: mmc2-ddr-1-8v-rev11-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -175,7 +167,7 @@
 		>;
 	};
 
-	mmc2_pins_ddr_rev20: mmc2_pins_ddr_rev20 {
+	mmc2_pins_ddr_rev20: mmc2-ddr-rev20-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -190,7 +182,7 @@
 		>;
 	};
 
-	mmc2_pins_hs200: mmc2_pins_hs200 {
+	mmc2_pins_hs200: mmc2-hs200-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -205,7 +197,7 @@
 		>;
 	};
 
-	mmc4_pins_default: mmc4_pins_default {
+	mmc4_pins_default: mmc4-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
 			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
@@ -216,7 +208,7 @@
 		>;
 	};
 
-	mmc4_pins_hs: mmc4_pins_hs {
+	mmc4_pins_hs: mmc4-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
 			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
@@ -227,7 +219,7 @@
 		>;
 	};
 
-	mmc3_pins_default: mmc3_pins_default {
+	mmc3_pins_default: mmc3-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
 			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
@@ -238,7 +230,7 @@
 		>;
 	};
 
-	mmc3_pins_hs: mmc3_pins_hs {
+	mmc3_pins_hs: mmc3-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
 			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
@@ -249,7 +241,7 @@
 		>;
 	};
 
-	mmc3_pins_sdr12: mmc3_pins_sdr12 {
+	mmc3_pins_sdr12: mmc3-sdr12-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
 			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
@@ -260,7 +252,7 @@
 		>;
 	};
 
-	mmc3_pins_sdr25: mmc3_pins_sdr25 {
+	mmc3_pins_sdr25: mmc3-sdr25-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
 			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
@@ -271,7 +263,7 @@
 		>;
 	};
 
-	mmc3_pins_sdr50: mmc3_pins_sdr50 {
+	mmc3_pins_sdr50: mmc3-sdr50-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
 			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
@@ -282,7 +274,7 @@
 		>;
 	};
 
-	mmc4_pins_sdr12: mmc4_pins_sdr12 {
+	mmc4_pins_sdr12: mmc4-sdr12-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
 			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
@@ -293,7 +285,7 @@
 		>;
 	};
 
-	mmc4_pins_sdr25: mmc4_pins_sdr25 {
+	mmc4_pins_sdr25: mmc4-sdr25-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
 			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
diff --git a/arch/arm/boot/dts/ti/omap/dra74x-p.dtsi b/arch/arm/boot/dts/ti/omap/dra74x-p.dtsi
new file mode 100644
index 000000000000..006189dad7a7
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra74x-p.dtsi
@@ -0,0 +1,27 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "dra74x.dtsi"
+
+/ {
+	compatible = "ti,dra762", "ti,dra7";
+
+	ocp {
+		emif1: emif@4c000000 {
+			compatible = "ti,emif-dra7xx";
+			reg = <0x4c000000 0x200>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+	};
+};
+
+/* MCAN interrupts are hard-wired to irqs 67, 68 */
+&crossbar_mpu {
+	ti,irqs-skip = <10 67 68 133 139 140>;
+};
diff --git a/arch/arm/boot/dts/ti/omap/dra74x.dtsi b/arch/arm/boot/dts/ti/omap/dra74x.dtsi
new file mode 100644
index 000000000000..cfb39dde4930
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/dra74x.dtsi
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Based on "omap4.dtsi"
+ */
+
+#include "dra7.dtsi"
+
+/ {
+	compatible = "ti,dra742", "ti,dra74", "ti,dra7";
+
+	cpus {
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+			operating-points-v2 = <&cpu0_opp_table>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
+			/* cooling options */
+			#cooling-cells = <2>; /* min followed by max */
+
+			vbb-supply = <&abb_mpu>;
+		};
+	};
+
+	aliases {
+		rproc0 = &ipu1;
+		rproc1 = &ipu2;
+		rproc2 = &dsp1;
+		rproc3 = &dsp2;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupt-parent = <&wakeupgen>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	ocp {
+		dsp2_system: dsp_system@41500000 {
+			compatible = "syscon";
+			reg = <0x41500000 0x100>;
+		};
+
+
+		target-module@41501000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x41501000 0x4>,
+			      <0x41501010 0x4>,
+			      <0x41501014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&dsp2_clkctrl DRA7_DSP2_MMU0_DSP2_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_dsp2 1>;
+			reset-names = "rstctrl";
+			ranges = <0x0 0x41501000 0x1000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			mmu0_dsp2: mmu@0 {
+				compatible = "ti,dra7-dsp-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,syscon-mmuconfig = <&dsp2_system 0x0>;
+			};
+		};
+
+		target-module@41502000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x41502000 0x4>,
+			      <0x41502010 0x4>,
+			      <0x41502014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+
+			clocks = <&dsp2_clkctrl DRA7_DSP2_MMU0_DSP2_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_dsp2 1>;
+			reset-names = "rstctrl";
+			ranges = <0x0 0x41502000 0x1000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			mmu1_dsp2: mmu@0 {
+				compatible = "ti,dra7-dsp-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,syscon-mmuconfig = <&dsp2_system 0x1>;
+			};
+		};
+
+		dsp2: dsp@41000000 {
+			compatible = "ti,dra7-dsp";
+			reg = <0x41000000 0x48000>,
+			      <0x41600000 0x8000>,
+			      <0x41700000 0x8000>;
+			reg-names = "l2ram", "l1pram", "l1dram";
+			ti,bootreg = <&scm_conf 0x560 10>;
+			iommus = <&mmu0_dsp2>, <&mmu1_dsp2>;
+			status = "disabled";
+			resets = <&prm_dsp2 0>;
+			clocks = <&dsp2_clkctrl DRA7_DSP2_MMU0_DSP2_CLKCTRL 0>;
+			firmware-name = "dra7-dsp2-fw.xe66";
+		};
+	};
+};
+
+&cpu0_opp_table {
+	opp-shared;
+};
+
+&dss {
+	reg = <0 0x80>,
+	      <0x4054 0x4>,
+	      <0x4300 0x20>,
+	      <0x9054 0x4>,
+	      <0x9300 0x20>;
+	reg-names = "dss", "pll1_clkctrl", "pll1",
+		    "pll2_clkctrl", "pll2";
+
+	clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>,
+		 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 12>,
+		 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 13>;
+	clock-names = "fck", "video1_clk", "video2_clk";
+};
+
+&mailbox5 {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
+		ti,mbox-tx = <6 2 2>;
+		ti,mbox-rx = <4 2 2>;
+		status = "disabled";
+	};
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
+		ti,mbox-tx = <5 2 2>;
+		ti,mbox-rx = <1 2 2>;
+		status = "disabled";
+	};
+};
+
+&mailbox6 {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
+		ti,mbox-tx = <6 2 2>;
+		ti,mbox-rx = <4 2 2>;
+		status = "disabled";
+	};
+	mbox_dsp2_ipc3x: mbox-dsp2-ipc3x {
+		ti,mbox-tx = <5 2 2>;
+		ti,mbox-rx = <1 2 2>;
+		status = "disabled";
+	};
+};
+
+&pcie1_rc {
+	compatible = "ti,dra746-pcie-rc", "ti,dra7-pcie";
+};
+
+&pcie1_ep {
+	compatible = "ti,dra746-pcie-ep", "ti,dra7-pcie-ep";
+};
+
+&pcie2_rc {
+	compatible = "ti,dra746-pcie-rc", "ti,dra7-pcie";
+};
+
+&l4_per3 {
+	segment@0 {
+		usb4_tm: target-module@140000 {         /* 0x48940000, ap 75 3c.0 */
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x140000 0x4>,
+			      <0x140010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_DMADISABLE>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			/* Domains (P, C): l3init_pwrdm, l3init_clkdm */
+			clocks = <&l3init_clkctrl DRA7_L3INIT_USB_OTG_SS4_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x140000 0x20000>;
+
+			omap_dwc3_4: omap_dwc3_4@0 {
+				compatible = "ti,dwc3";
+				reg = <0 0x10000>;
+				interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				utmi-mode = <2>;
+				ranges;
+				status = "disabled";
+				usb4: usb@10000 {
+					compatible = "snps,dwc3";
+					reg = <0x10000 0x17000>;
+					interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "peripheral",
+							  "host",
+							  "otg";
+					maximum-speed = "high-speed";
+					dr_mode = "otg";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/ti/omap/dra76-evm.dts
index 1fb6f13fb5e2..cf9c3d35b049 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/dra76-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -13,11 +13,52 @@
 	model = "TI DRA762 EVM";
 	compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7";
 
+	aliases {
+		display0 = &hdmi0;
+
+		sound0 = &sound0;
+		sound1 = &hdmi;
+	};
+
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x80000000 0x0 0x80000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ipu2_cma_pool: ipu2_cma@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x95800000 0x0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp1_cma_pool: dsp1_cma@99000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x99000000 0x0 0x4000000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu1_cma_pool: ipu1_cma@9d000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9d000000 0x0 0x2000000>;
+			reusable;
+			status = "okay";
+		};
+
+		dsp2_cma_pool: dsp2_cma@9f000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x9f000000 0x0 0x800000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	vsys_12v0: fixedregulator-vsys12v0 {
 		/* main supply */
 		compatible = "regulator-fixed";
@@ -116,6 +157,48 @@
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 	};
+
+	hdmi0: connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
+
+	tpd12s015: encoder {
+		compatible = "ti,tpd12s015";
+
+		gpios = <&gpio7 30 GPIO_ACTIVE_HIGH>,   /* gpio7_30, CT CP HPD */
+			<&gpio7 31 GPIO_ACTIVE_HIGH>,   /* gpio7_31, LS OE */
+			<&gpio7 12 GPIO_ACTIVE_HIGH>;   /* gpio7_12/sp1_cs2, HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
 };
 
 &i2c1 {
@@ -266,7 +349,7 @@
 	};
 
 	pcf_lcd: pcf8757@20 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x20>;
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -277,7 +360,7 @@
 	};
 
 	pcf_gpio_21: pcf8757@21 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x21>;
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -288,11 +371,11 @@
 	};
 
 	pcf_hdmi: pcf8575@26 {
-		compatible = "ti,pcf8575", "nxp,pcf8575";
+		compatible = "nxp,pcf8575";
 		reg = <0x26>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		p1 {
+		hdmi-audio-hog {
 			/* vin6_sel_s0: high: VIN6, low: audio */
 			gpio-hog;
 			gpios = <1 GPIO_ACTIVE_HIGH>;
@@ -365,25 +448,23 @@
 	status = "disabled";
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
-
-	dual_emac;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&dp83867_0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&dp83867_1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	dp83867_0: ethernet-phy@2 {
 		reg = <2>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
@@ -411,9 +492,26 @@
 	phy-supply = <&ldo3_reg>;
 };
 
+&dss {
+	status = "okay";
+	vdda_video-supply = <&ldo5_reg>;
+};
+
+&hdmi {
+	status = "okay";
+
+	vdda-supply = <&ldo1_reg>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};
+
 &qspi {
 	spi-max-frequency = <96000000>;
-	m25p80@0 {
+	flash@0 {
 		spi-max-frequency = <96000000>;
 	};
 };
@@ -435,11 +533,11 @@
 };
 
 &extcon_usb1 {
-	vbus-gpio = <&pcf_lcd 14 GPIO_ACTIVE_HIGH>;
+	vbus-gpios = <&pcf_lcd 14 GPIO_ACTIVE_HIGH>;
 };
 
 &extcon_usb2 {
-	vbus-gpio = <&pcf_lcd 15 GPIO_ACTIVE_HIGH>;
+	vbus-gpios = <&pcf_lcd 15 GPIO_ACTIVE_HIGH>;
 };
 
 &m_can0 {
@@ -447,3 +545,23 @@
 		max-bitrate = <5000000>;
 	};
 };
+
+&ipu2 {
+	status = "okay";
+	memory-region = <&ipu2_cma_pool>;
+};
+
+&ipu1 {
+	status = "okay";
+	memory-region = <&ipu1_cma_pool>;
+};
+
+&dsp1 {
+	status = "okay";
+	memory-region = <&dsp1_cma_pool>;
+};
+
+&dsp2 {
+	status = "okay";
+	memory-region = <&dsp2_cma_pool>;
+};
diff --git a/arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi b/arch/arm/boot/dts/ti/omap/dra76x-mmc-iodelay.dtsi
index fdca48186916..4690554dfa6e 100644
--- a/arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra76x-mmc-iodelay.dtsi
@@ -27,7 +27,7 @@
  */
 
 &dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
+	mmc1_pins_default: mmc1-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
@@ -38,7 +38,7 @@
 		>;
 	};
 
-	mmc1_pins_hs: mmc1_pins_hs {
+	mmc1_pins_hs: mmc1-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_cmd.cmd */
@@ -49,7 +49,7 @@
 		>;
 	};
 
-	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+	mmc1_pins_sdr50: mmc1-sdr50-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -60,7 +60,7 @@
 		>;
 	};
 
-	mmc1_pins_ddr50: mmc1_pins_ddr50 {
+	mmc1_pins_ddr50: mmc1-ddr50-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
 			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
@@ -71,7 +71,7 @@
 		>;
 	};
 
-	mmc2_pins_default: mmc2_pins_default {
+	mmc2_pins_default: mmc2-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -86,7 +86,7 @@
 		>;
 	};
 
-	mmc2_pins_hs200: mmc2_pins_hs200 {
+	mmc2_pins_hs200: mmc2-hs200-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
 			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
@@ -101,7 +101,7 @@
 		>;
 	};
 
-	mmc3_pins_default: mmc3_pins_default {
+	mmc3_pins_default: mmc3-default-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
 			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
@@ -112,7 +112,7 @@
 		>;
 	};
 
-	mmc4_pins_hs: mmc4_pins_hs {
+	mmc4_pins_hs: mmc4-hs-pins {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
 			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
diff --git a/arch/arm/boot/dts/dra76x.dtsi b/arch/arm/boot/dts/ti/omap/dra76x.dtsi
index cdcba3f561c4..1045eb24aa0d 100644
--- a/arch/arm/boot/dts/dra76x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra76x.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "dra74x.dtsi"
@@ -32,8 +32,8 @@
 				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "int0", "int1";
-				clocks = <&mcan_clk>, <&l3_iclk_div>;
-				clock-names = "cclk", "hclk";
+				clocks = <&l3_iclk_div>, <&mcan_clk>;
+				clock-names = "hclk", "cclk";
 				bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>;
 			};
 		};
@@ -41,9 +41,46 @@
 
 };
 
-/* MCAN interrupts are hard-wired to irqs 67, 68 */
-&crossbar_mpu {
-	ti,irqs-skip = <10 67 68 133 139 140>;
+&l4_per3 {
+	target-module@1b0000 {			/* 0x489b0000, ap 25 34.0 */
+		compatible = "ti,sysc-omap4", "ti,sysc";
+		reg = <0x1b0000 0x4>,
+		      <0x1b0010 0x4>;
+		reg-names = "rev", "sysc";
+		ti,sysc-midle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>;
+		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>;
+		clocks = <&cam_clkctrl DRA7_CAM_VIP3_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x1b0000 0x10000>;
+
+		cal: cal@0 {
+			compatible = "ti,dra76-cal";
+			reg = <0x0000 0x400>,
+			      <0x0800 0x40>,
+			      <0x0900 0x40>;
+			reg-names = "cal_top",
+				    "cal_rx_core0",
+				    "cal_rx_core1";
+			interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+			ti,camerrx-control = <&scm_conf 0x6dc>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				csi2_0: port@0 {
+					reg = <0>;
+				};
+				csi2_1: port@1 {
+					reg = <1>;
+				};
+			};
+		};
+	};
 };
 
 &scm_conf_clocks {
@@ -53,8 +90,8 @@
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x03fc>;
-		ti,bit-shift=<20>;
-		ti,latch-bit=<26>;
+		ti,bit-shift = <20>;
+		ti,latch-bit = <26>;
 		assigned-clocks = <&dpll_gmac_h14x2_ctrl_ck>;
 		assigned-clock-rates = <80000000>;
 	};
@@ -65,7 +102,7 @@
 		clocks = <&dpll_gmac_ck>, <&dpll_gmac_h14x2_ctrl_ck>;
 		reg = <0x3fc>;
 		ti,bit-shift = <29>;
-		ti,latch-bit=<26>;
+		ti,latch-bit = <26>;
 		assigned-clocks = <&dpll_gmac_h14x2_ctrl_mux_ck>;
 		assigned-clock-parents = <&dpll_gmac_h14x2_ctrl_ck>;
 	};
@@ -86,3 +123,38 @@
 &usb4_tm {
 	status = "disabled";
 };
+
+&mmc3 {
+	/* dra76x is not affected by i887 */
+	max-frequency = <96000000>;
+};
+
+&cpu0_opp_table {
+	opp-1800000000 {
+		/* OPP Plus */
+		opp-hz = /bits/ 64 <1800000000>;
+		opp-microvolt = <1250000 950000 1250000>,
+				<1250000 950000 1250000>;
+		opp-supported-hw = <0xFF 0x08>;
+	};
+};
+
+&opp_supply_mpu {
+	ti,efuse-settings = <
+	/* uV   offset */
+	1060000 0x0
+	1160000 0x4
+	1210000 0x8
+	1250000 0xC
+	>;
+};
+
+&abb_mpu {
+	ti,abb_info = <
+	/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+	1060000		0	0x0	0 0x02000000 0x01F00000
+	1160000		0	0x4	0 0x02000000 0x01F00000
+	1210000		0	0x8	0 0x02000000 0x01F00000
+	1250000		0	0xC	0 0x02000000 0x01F00000
+	>;
+};
diff --git a/arch/arm/boot/dts/dra7xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/dra7xx-clocks.dtsi
index 93e1eb83bed9..04a7a6d1d529 100644
--- a/arch/arm/boot/dts/dra7xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7xx-clocks.dtsi
@@ -5,210 +5,244 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &cm_core_aon_clocks {
-	atl_clkin0_ck: atl_clkin0_ck {
+	atl_clkin0_ck: clock-atl-clkin0 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin0_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	atl_clkin1_ck: atl_clkin1_ck {
+	atl_clkin1_ck: clock-atl-clkin1 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin1_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	atl_clkin2_ck: atl_clkin2_ck {
+	atl_clkin2_ck: clock-atl-clkin2 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin2_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	atl_clkin3_ck: atl_clkin3_ck {
+	atl_clkin3_ck: clock-atl-clkin3 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin3_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	hdmi_clkin_ck: hdmi_clkin_ck {
+	hdmi_clkin_ck: clock-hdmi-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "hdmi_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	mlb_clkin_ck: mlb_clkin_ck {
+	mlb_clkin_ck: clock-mlb-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "mlb_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	mlbp_clkin_ck: mlbp_clkin_ck {
+	mlbp_clkin_ck: clock-mlbp-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "mlbp_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	pciesref_acs_clk_ck: pciesref_acs_clk_ck {
+	pciesref_acs_clk_ck: clock-pciesref-acs {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pciesref_acs_clk_ck";
 		clock-frequency = <100000000>;
 	};
 
-	ref_clkin0_ck: ref_clkin0_ck {
+	ref_clkin0_ck: clock-ref-clkin0 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin0_ck";
 		clock-frequency = <0>;
 	};
 
-	ref_clkin1_ck: ref_clkin1_ck {
+	ref_clkin1_ck: clock-ref-clkin1 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin1_ck";
 		clock-frequency = <0>;
 	};
 
-	ref_clkin2_ck: ref_clkin2_ck {
+	ref_clkin2_ck: clock-ref-clkin2 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin2_ck";
 		clock-frequency = <0>;
 	};
 
-	ref_clkin3_ck: ref_clkin3_ck {
+	ref_clkin3_ck: clock-ref-clkin3 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin3_ck";
 		clock-frequency = <0>;
 	};
 
-	rmii_clk_ck: rmii_clk_ck {
+	rmii_clk_ck: clock-rmii {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "rmii_clk_ck";
 		clock-frequency = <0>;
 	};
 
-	sdvenc_clkin_ck: sdvenc_clkin_ck {
+	sdvenc_clkin_ck: clock-sdvenc-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sdvenc_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	secure_32k_clk_src_ck: secure_32k_clk_src_ck {
+	secure_32k_clk_src_ck: clock-secure-32k-clk-src {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "secure_32k_clk_src_ck";
 		clock-frequency = <32768>;
 	};
 
-	sys_clk32_crystal_ck: sys_clk32_crystal_ck {
+	sys_clk32_crystal_ck: clock-sys-clk32-crystal {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_clk32_crystal_ck";
 		clock-frequency = <32768>;
 	};
 
-	sys_clk32_pseudo_ck: sys_clk32_pseudo_ck {
+	sys_clk32_pseudo_ck: clock-sys-clk32-pseudo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sys_clk32_pseudo_ck";
 		clocks = <&sys_clkin1>;
 		clock-mult = <1>;
 		clock-div = <610>;
 	};
 
-	virt_12000000_ck: virt_12000000_ck {
+	virt_12000000_ck: clock-virt-12000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_12000000_ck";
 		clock-frequency = <12000000>;
 	};
 
-	virt_13000000_ck: virt_13000000_ck {
+	virt_13000000_ck: clock-virt-13000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_13000000_ck";
 		clock-frequency = <13000000>;
 	};
 
-	virt_16800000_ck: virt_16800000_ck {
+	virt_16800000_ck: clock-virt-16800000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_16800000_ck";
 		clock-frequency = <16800000>;
 	};
 
-	virt_19200000_ck: virt_19200000_ck {
+	virt_19200000_ck: clock-virt-19200000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
-	virt_20000000_ck: virt_20000000_ck {
+	virt_20000000_ck: clock-virt-20000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_20000000_ck";
 		clock-frequency = <20000000>;
 	};
 
-	virt_26000000_ck: virt_26000000_ck {
+	virt_26000000_ck: clock-virt-26000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
-	virt_27000000_ck: virt_27000000_ck {
+	virt_27000000_ck: clock-virt-27000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_27000000_ck";
 		clock-frequency = <27000000>;
 	};
 
-	virt_38400000_ck: virt_38400000_ck {
+	virt_38400000_ck: clock-virt-38400000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_38400000_ck";
 		clock-frequency = <38400000>;
 	};
 
-	sys_clkin2: sys_clkin2 {
+	sys_clkin2: clock-sys-clkin2 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_clkin2";
 		clock-frequency = <22579200>;
 	};
 
-	usb_otg_clkin_ck: usb_otg_clkin_ck {
+	usb_otg_clkin_ck: clock-usb-otg-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "usb_otg_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video1_clkin_ck: video1_clkin_ck {
+	video1_clkin_ck: clock-video1-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video1_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video1_m2_clkin_ck: video1_m2_clkin_ck {
+	video1_m2_clkin_ck: clock-video1-m2-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video1_m2_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video2_clkin_ck: video2_clkin_ck {
+	video2_clkin_ck: clock-video2-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video2_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video2_m2_clkin_ck: video2_m2_clkin_ck {
+	video2_m2_clkin_ck: clock-video2-m2-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video2_m2_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	dpll_abe_ck: dpll_abe_ck@1e0 {
+	dpll_abe_ck: clock@1e0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-m4xen-clock";
+		clock-output-names = "dpll_abe_ck";
 		clocks = <&abe_dpll_clk_mux>, <&abe_dpll_bypass_clk_mux>;
 		reg = <0x01e0>, <0x01e4>, <0x01ec>, <0x01e8>;
 	};
 
-	dpll_abe_x2_ck: dpll_abe_x2_ck {
+	dpll_abe_x2_ck: clock-dpll-abe-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_abe_x2_ck";
 		clocks = <&dpll_abe_ck>;
 	};
 
-	dpll_abe_m2x2_ck: dpll_abe_m2x2_ck@1f0 {
+	dpll_abe_m2x2_ck: clock-dpll-abe-m2x2-8@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -217,18 +251,20 @@
 		ti,invert-autoidle-bit;
 	};
 
-	abe_clk: abe_clk@108 {
+	abe_clk: clock-abe@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_clk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x0108>;
 		ti,index-power-of-two;
 	};
 
-	dpll_abe_m2_ck: dpll_abe_m2_ck@1f0 {
+	dpll_abe_m2_ck: clock-dpll-abe-m2-8@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2_ck";
 		clocks = <&dpll_abe_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -237,9 +273,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_abe_m3x2_ck: dpll_abe_m3x2_ck@1f4 {
+	dpll_abe_m3x2_ck: clock-dpll-abe-m3x2-8@1f4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m3x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -248,30 +285,34 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_byp_mux: dpll_core_byp_mux@12c {
+	dpll_core_byp_mux: clock-dpll-core-byp-mux-23@12c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_core_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x012c>;
 	};
 
-	dpll_core_ck: dpll_core_ck@120 {
+	dpll_core_ck: clock@120 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin1>, <&dpll_core_byp_mux>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
 
-	dpll_core_x2_ck: dpll_core_x2_ck {
+	dpll_core_x2_ck: clock-dpll-core-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_h12x2_ck: dpll_core_h12x2_ck@13c {
+	dpll_core_h12x2_ck: clock-dpll-core-h12x2-8@13c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h12x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -280,24 +321,27 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mpu_dpll_hs_clk_div: mpu_dpll_hs_clk_div {
+	mpu_dpll_hs_clk_div: clock-mpu-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck@160 {
+	dpll_mpu_ck: clock@160 {
 		#clock-cells = <0>;
 		compatible = "ti,omap5-mpu-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin1>, <&mpu_dpll_hs_clk_div>;
 		reg = <0x0160>, <0x0164>, <0x016c>, <0x0168>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck@170 {
+	dpll_mpu_m2_ck: clock-dpll-mpu-m2-8@170 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -306,42 +350,47 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mpu_dclk_div: mpu_dclk_div {
+	mpu_dclk_div: clock-mpu-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_dclk_div";
 		clocks = <&dpll_mpu_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dsp_dpll_hs_clk_div: dsp_dpll_hs_clk_div {
+	dsp_dpll_hs_clk_div: clock-dsp-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dsp_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_dsp_byp_mux: dpll_dsp_byp_mux@240 {
+	dpll_dsp_byp_mux: clock-dpll-dsp-byp-mux-23@240 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_dsp_byp_mux";
 		clocks = <&sys_clkin1>, <&dsp_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x0240>;
 	};
 
-	dpll_dsp_ck: dpll_dsp_ck@234 {
+	dpll_dsp_ck: clock@234 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_dsp_ck";
 		clocks = <&sys_clkin1>, <&dpll_dsp_byp_mux>;
 		reg = <0x0234>, <0x0238>, <0x0240>, <0x023c>;
 		assigned-clocks = <&dpll_dsp_ck>;
 		assigned-clock-rates = <600000000>;
 	};
 
-	dpll_dsp_m2_ck: dpll_dsp_m2_ck@244 {
+	dpll_dsp_m2_ck: clock-dpll-dsp-m2-8@244 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_dsp_m2_ck";
 		clocks = <&dpll_dsp_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -352,34 +401,38 @@
 		assigned-clock-rates = <600000000>;
 	};
 
-	iva_dpll_hs_clk_div: iva_dpll_hs_clk_div {
+	iva_dpll_hs_clk_div: clock-iva-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "iva_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_iva_byp_mux: dpll_iva_byp_mux@1ac {
+	dpll_iva_byp_mux: clock-dpll-iva-byp-mux-23@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_iva_byp_mux";
 		clocks = <&sys_clkin1>, <&iva_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x01ac>;
 	};
 
-	dpll_iva_ck: dpll_iva_ck@1a0 {
+	dpll_iva_ck: clock@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_iva_ck";
 		clocks = <&sys_clkin1>, <&dpll_iva_byp_mux>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 		assigned-clocks = <&dpll_iva_ck>;
 		assigned-clock-rates = <1165000000>;
 	};
 
-	dpll_iva_m2_ck: dpll_iva_m2_ck@1b0 {
+	dpll_iva_m2_ck: clock-dpll-iva-m2-8@1b0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_m2_ck";
 		clocks = <&dpll_iva_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -390,34 +443,38 @@
 		assigned-clock-rates = <388333334>;
 	};
 
-	iva_dclk: iva_dclk {
+	iva_dclk: clock-iva-dclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "iva_dclk";
 		clocks = <&dpll_iva_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_gpu_byp_mux: dpll_gpu_byp_mux@2e4 {
+	dpll_gpu_byp_mux: clock-dpll-gpu-byp-mux-23@2e4 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_gpu_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x02e4>;
 	};
 
-	dpll_gpu_ck: dpll_gpu_ck@2d8 {
+	dpll_gpu_ck: clock@2d8 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_gpu_ck";
 		clocks = <&sys_clkin1>, <&dpll_gpu_byp_mux>;
 		reg = <0x02d8>, <0x02dc>, <0x02e4>, <0x02e0>;
 		assigned-clocks = <&dpll_gpu_ck>;
 		assigned-clock-rates = <1277000000>;
 	};
 
-	dpll_gpu_m2_ck: dpll_gpu_m2_ck@2e8 {
+	dpll_gpu_m2_ck: clock-dpll-gpu-m2-8@2e8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gpu_m2_ck";
 		clocks = <&dpll_gpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -428,9 +485,10 @@
 		assigned-clock-rates = <425666667>;
 	};
 
-	dpll_core_m2_ck: dpll_core_m2_ck@130 {
+	dpll_core_m2_ck: clock-dpll-core-m2-8@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m2_ck";
 		clocks = <&dpll_core_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -439,32 +497,36 @@
 		ti,invert-autoidle-bit;
 	};
 
-	core_dpll_out_dclk_div: core_dpll_out_dclk_div {
+	core_dpll_out_dclk_div: clock-core-dpll-out-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "core_dpll_out_dclk_div";
 		clocks = <&dpll_core_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_ddr_byp_mux: dpll_ddr_byp_mux@21c {
+	dpll_ddr_byp_mux: clock-dpll-ddr-byp-mux-23@21c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_ddr_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x021c>;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck@210 {
+	dpll_ddr_ck: clock@210 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_ddr_ck";
 		clocks = <&sys_clkin1>, <&dpll_ddr_byp_mux>;
 		reg = <0x0210>, <0x0214>, <0x021c>, <0x0218>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck@220 {
+	dpll_ddr_m2_ck: clock-dpll-ddr-m2-8@220 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m2_ck";
 		clocks = <&dpll_ddr_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -473,24 +535,27 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_byp_mux: dpll_gmac_byp_mux@2b4 {
+	dpll_gmac_byp_mux: clock-dpll-gmac-byp-mux-23@2b4 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_gmac_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x02b4>;
 	};
 
-	dpll_gmac_ck: dpll_gmac_ck@2a8 {
+	dpll_gmac_ck: clock@2a8 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_gmac_ck";
 		clocks = <&sys_clkin1>, <&dpll_gmac_byp_mux>;
 		reg = <0x02a8>, <0x02ac>, <0x02b4>, <0x02b0>;
 	};
 
-	dpll_gmac_m2_ck: dpll_gmac_m2_ck@2b8 {
+	dpll_gmac_m2_ck: clock-dpll-gmac-m2-8@2b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_m2_ck";
 		clocks = <&dpll_gmac_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -499,72 +564,81 @@
 		ti,invert-autoidle-bit;
 	};
 
-	video2_dclk_div: video2_dclk_div {
+	video2_dclk_div: clock-video2-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video2_dclk_div";
 		clocks = <&video2_m2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video1_dclk_div: video1_dclk_div {
+	video1_dclk_div: clock-video1-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video1_dclk_div";
 		clocks = <&video1_m2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	hdmi_dclk_div: hdmi_dclk_div {
+	hdmi_dclk_div: clock-hdmi-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "hdmi_dclk_div";
 		clocks = <&hdmi_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	per_dpll_hs_clk_div: per_dpll_hs_clk_div {
+	per_dpll_hs_clk_div: clock-per-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	usb_dpll_hs_clk_div: usb_dpll_hs_clk_div {
+	usb_dpll_hs_clk_div: clock-usb-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "usb_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <3>;
 	};
 
-	eve_dpll_hs_clk_div: eve_dpll_hs_clk_div {
+	eve_dpll_hs_clk_div: clock-eve-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "eve_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_eve_byp_mux: dpll_eve_byp_mux@290 {
+	dpll_eve_byp_mux: clock-dpll-eve-byp-mux-23@290 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_eve_byp_mux";
 		clocks = <&sys_clkin1>, <&eve_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x0290>;
 	};
 
-	dpll_eve_ck: dpll_eve_ck@284 {
+	dpll_eve_ck: clock@284 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_eve_ck";
 		clocks = <&sys_clkin1>, <&dpll_eve_byp_mux>;
 		reg = <0x0284>, <0x0288>, <0x0290>, <0x028c>;
 	};
 
-	dpll_eve_m2_ck: dpll_eve_m2_ck@294 {
+	dpll_eve_m2_ck: clock-dpll-eve-m2-8@294 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_eve_m2_ck";
 		clocks = <&dpll_eve_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -573,17 +647,19 @@
 		ti,invert-autoidle-bit;
 	};
 
-	eve_dclk_div: eve_dclk_div {
+	eve_dclk_div: clock-eve-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "eve_dclk_div";
 		clocks = <&dpll_eve_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_core_h13x2_ck: dpll_core_h13x2_ck@140 {
+	dpll_core_h13x2_ck: clock-dpll-core-h13x2-8@140 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h13x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -592,9 +668,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h14x2_ck: dpll_core_h14x2_ck@144 {
+	dpll_core_h14x2_ck: clock-dpll-core-h14x2-8@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h14x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -603,9 +680,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h22x2_ck: dpll_core_h22x2_ck@154 {
+	dpll_core_h22x2_ck: clock-dpll-core-h22x2-8@154 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h22x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -614,9 +692,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h23x2_ck: dpll_core_h23x2_ck@158 {
+	dpll_core_h23x2_ck: clock-dpll-core-h23x2-8@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h23x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -625,9 +704,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h24x2_ck: dpll_core_h24x2_ck@15c {
+	dpll_core_h24x2_ck: clock-dpll-core-h24x2-8@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h24x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -636,15 +716,17 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_ddr_x2_ck: dpll_ddr_x2_ck {
+	dpll_ddr_x2_ck: clock-dpll-ddr-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_ddr_x2_ck";
 		clocks = <&dpll_ddr_ck>;
 	};
 
-	dpll_ddr_h11x2_ck: dpll_ddr_h11x2_ck@228 {
+	dpll_ddr_h11x2_ck: clock-dpll-ddr-h11x2-8@228 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_h11x2_ck";
 		clocks = <&dpll_ddr_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -653,15 +735,17 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_dsp_x2_ck: dpll_dsp_x2_ck {
+	dpll_dsp_x2_ck: clock-dpll-dsp-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_dsp_x2_ck";
 		clocks = <&dpll_dsp_ck>;
 	};
 
-	dpll_dsp_m3x2_ck: dpll_dsp_m3x2_ck@248 {
+	dpll_dsp_m3x2_ck: clock-dpll-dsp-m3x2-8@248 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_dsp_m3x2_ck";
 		clocks = <&dpll_dsp_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -672,15 +756,17 @@
 		assigned-clock-rates = <400000000>;
 	};
 
-	dpll_gmac_x2_ck: dpll_gmac_x2_ck {
+	dpll_gmac_x2_ck: clock-dpll-gmac-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_gmac_x2_ck";
 		clocks = <&dpll_gmac_ck>;
 	};
 
-	dpll_gmac_h11x2_ck: dpll_gmac_h11x2_ck@2c0 {
+	dpll_gmac_h11x2_ck: clock-dpll-gmac-h11x2-8@2c0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_h11x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -689,9 +775,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_h12x2_ck: dpll_gmac_h12x2_ck@2c4 {
+	dpll_gmac_h12x2_ck: clock-dpll-gmac-h12x2-8@2c4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_h12x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -700,9 +787,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_h13x2_ck: dpll_gmac_h13x2_ck@2c8 {
+	dpll_gmac_h13x2_ck: clock-dpll-gmac-h13x2-8@2c8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_h13x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -711,9 +799,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_m3x2_ck: dpll_gmac_m3x2_ck@2bc {
+	dpll_gmac_m3x2_ck: clock-dpll-gmac-m3x2-8@2bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_m3x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -722,33 +811,37 @@
 		ti,invert-autoidle-bit;
 	};
 
-	gmii_m_clk_div: gmii_m_clk_div {
+	gmii_m_clk_div: clock-gmii-m-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "gmii_m_clk_div";
 		clocks = <&dpll_gmac_h11x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	hdmi_clk2_div: hdmi_clk2_div {
+	hdmi_clk2_div: clock-hdmi-clk2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "hdmi_clk2_div";
 		clocks = <&hdmi_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	hdmi_div_clk: hdmi_div_clk {
+	hdmi_div_clk: clock-hdmi-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "hdmi_div_clk";
 		clocks = <&hdmi_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l3_iclk_div: l3_iclk_div@100 {
+	l3_iclk_div: clock-l3-iclk-div-4@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3_iclk_div";
 		ti,max-div = <2>;
 		ti,bit-shift = <4>;
 		reg = <0x0100>;
@@ -756,384 +849,420 @@
 		ti,index-power-of-two;
 	};
 
-	l4_root_clk_div: l4_root_clk_div {
+	l4_root_clk_div: clock-l4-root-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4_root_clk_div";
 		clocks = <&l3_iclk_div>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	video1_clk2_div: video1_clk2_div {
+	video1_clk2_div: clock-video1-clk2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video1_clk2_div";
 		clocks = <&video1_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video1_div_clk: video1_div_clk {
+	video1_div_clk: clock-video1-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video1_div_clk";
 		clocks = <&video1_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video2_clk2_div: video2_clk2_div {
+	video2_clk2_div: clock-video2-clk2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video2_clk2_div";
 		clocks = <&video2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video2_div_clk: video2_div_clk {
+	video2_div_clk: clock-video2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video2_div_clk";
 		clocks = <&video2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	ipu1_gfclk_mux: ipu1_gfclk_mux@520 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dpll_abe_m2x2_ck>, <&dpll_core_h22x2_ck>;
-		ti,bit-shift = <24>;
-		reg = <0x0520>;
-		assigned-clocks = <&ipu1_gfclk_mux>;
-		assigned-clock-parents = <&dpll_core_h22x2_ck>;
-	};
-
-	dummy_ck: dummy_ck {
+	dummy_ck: clock-dummy {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "dummy_ck";
 		clock-frequency = <0>;
 	};
 };
 &prm_clocks {
-	sys_clkin1: sys_clkin1@110 {
+	sys_clkin1: clock-sys-clkin1@110 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin1";
 		clocks = <&virt_12000000_ck>, <&virt_20000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
 		reg = <0x0110>;
 		ti,index-starts-at-one;
 	};
 
-	abe_dpll_sys_clk_mux: abe_dpll_sys_clk_mux@118 {
+	abe_dpll_sys_clk_mux: clock-abe-dpll-sys-clk-mux@118 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_sys_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x0118>;
 	};
 
-	abe_dpll_bypass_clk_mux: abe_dpll_bypass_clk_mux@114 {
+	abe_dpll_bypass_clk_mux: clock-abe-dpll-bypass-clk-mux@114 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_bypass_clk_mux";
 		clocks = <&abe_dpll_sys_clk_mux>, <&sys_32k_ck>;
 		reg = <0x0114>;
 	};
 
-	abe_dpll_clk_mux: abe_dpll_clk_mux@10c {
+	abe_dpll_clk_mux: clock-abe-dpll-clk-mux@10c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_clk_mux";
 		clocks = <&abe_dpll_sys_clk_mux>, <&sys_32k_ck>;
 		reg = <0x010c>;
 	};
 
-	abe_24m_fclk: abe_24m_fclk@11c {
+	abe_24m_fclk: clock-abe-24m@11c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_24m_fclk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		reg = <0x011c>;
 		ti,dividers = <8>, <16>;
 	};
 
-	aess_fclk: aess_fclk@178 {
+	aess_fclk: clock-aess@178 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "aess_fclk";
 		clocks = <&abe_clk>;
 		reg = <0x0178>;
 		ti,max-div = <2>;
 	};
 
-	abe_giclk_div: abe_giclk_div@174 {
+	abe_giclk_div: clock-abe-giclk-div@174 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_giclk_div";
 		clocks = <&aess_fclk>;
 		reg = <0x0174>;
 		ti,max-div = <2>;
 	};
 
-	abe_lp_clk_div: abe_lp_clk_div@1d8 {
+	abe_lp_clk_div: clock-abe-lp-clk-div@1d8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_lp_clk_div";
 		clocks = <&dpll_abe_m2x2_ck>;
 		reg = <0x01d8>;
 		ti,dividers = <16>, <32>;
 	};
 
-	abe_sys_clk_div: abe_sys_clk_div@120 {
+	abe_sys_clk_div: clock-abe-sys-clk-div@120 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_sys_clk_div";
 		clocks = <&sys_clkin1>;
 		reg = <0x0120>;
 		ti,max-div = <2>;
 	};
 
-	adc_gfclk_mux: adc_gfclk_mux@1dc {
+	adc_gfclk_mux: clock-adc-gfclk-mux@1dc {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "adc_gfclk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>, <&sys_32k_ck>;
 		reg = <0x01dc>;
 	};
 
-	sys_clk1_dclk_div: sys_clk1_dclk_div@1c8 {
+	sys_clk1_dclk_div: clock-sys-clk1-dclk-div@1c8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "sys_clk1_dclk_div";
 		clocks = <&sys_clkin1>;
 		ti,max-div = <64>;
 		reg = <0x01c8>;
 		ti,index-power-of-two;
 	};
 
-	sys_clk2_dclk_div: sys_clk2_dclk_div@1cc {
+	sys_clk2_dclk_div: clock-sys-clk2-dclk-div@1cc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "sys_clk2_dclk_div";
 		clocks = <&sys_clkin2>;
 		ti,max-div = <64>;
 		reg = <0x01cc>;
 		ti,index-power-of-two;
 	};
 
-	per_abe_x1_dclk_div: per_abe_x1_dclk_div@1bc {
+	per_abe_x1_dclk_div: clock-per-abe-x1-dclk-div@1bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "per_abe_x1_dclk_div";
 		clocks = <&dpll_abe_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01bc>;
 		ti,index-power-of-two;
 	};
 
-	dsp_gclk_div: dsp_gclk_div@18c {
+	dsp_gclk_div: clock-dsp-gclk-div@18c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dsp_gclk_div";
 		clocks = <&dpll_dsp_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x018c>;
 		ti,index-power-of-two;
 	};
 
-	gpu_dclk: gpu_dclk@1a0 {
+	gpu_dclk: clock-gpu-dclk@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "gpu_dclk";
 		clocks = <&dpll_gpu_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01a0>;
 		ti,index-power-of-two;
 	};
 
-	emif_phy_dclk_div: emif_phy_dclk_div@190 {
+	emif_phy_dclk_div: clock-emif-phy-dclk-div@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "emif_phy_dclk_div";
 		clocks = <&dpll_ddr_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x0190>;
 		ti,index-power-of-two;
 	};
 
-	gmac_250m_dclk_div: gmac_250m_dclk_div@19c {
+	gmac_250m_dclk_div: clock-gmac-250m-dclk-div@19c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "gmac_250m_dclk_div";
 		clocks = <&dpll_gmac_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x019c>;
 		ti,index-power-of-two;
 	};
 
-	gmac_main_clk: gmac_main_clk {
+	gmac_main_clk: clock-gmac-main {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "gmac_main_clk";
 		clocks = <&gmac_250m_dclk_div>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l3init_480m_dclk_div: l3init_480m_dclk_div@1ac {
+	l3init_480m_dclk_div: clock-l3init-480m-dclk-div@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3init_480m_dclk_div";
 		clocks = <&dpll_usb_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01ac>;
 		ti,index-power-of-two;
 	};
 
-	usb_otg_dclk_div: usb_otg_dclk_div@184 {
+	usb_otg_dclk_div: clock-usb-otg-dclk-div@184 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "usb_otg_dclk_div";
 		clocks = <&usb_otg_clkin_ck>;
 		ti,max-div = <64>;
 		reg = <0x0184>;
 		ti,index-power-of-two;
 	};
 
-	sata_dclk_div: sata_dclk_div@1c0 {
+	sata_dclk_div: clock-sata-dclk-div@1c0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "sata_dclk_div";
 		clocks = <&sys_clkin1>;
 		ti,max-div = <64>;
 		reg = <0x01c0>;
 		ti,index-power-of-two;
 	};
 
-	pcie2_dclk_div: pcie2_dclk_div@1b8 {
+	pcie2_dclk_div: clock-pcie2-dclk-div@1b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "pcie2_dclk_div";
 		clocks = <&dpll_pcie_ref_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01b8>;
 		ti,index-power-of-two;
 	};
 
-	pcie_dclk_div: pcie_dclk_div@1b4 {
+	pcie_dclk_div: clock-pcie-dclk-div@1b4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "pcie_dclk_div";
 		clocks = <&apll_pcie_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01b4>;
 		ti,index-power-of-two;
 	};
 
-	emu_dclk_div: emu_dclk_div@194 {
+	emu_dclk_div: clock-emu-dclk-div@194 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "emu_dclk_div";
 		clocks = <&sys_clkin1>;
 		ti,max-div = <64>;
 		reg = <0x0194>;
 		ti,index-power-of-two;
 	};
 
-	secure_32k_dclk_div: secure_32k_dclk_div@1c4 {
+	secure_32k_dclk_div: clock-secure-32k-dclk-div@1c4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "secure_32k_dclk_div";
 		clocks = <&secure_32k_clk_src_ck>;
 		ti,max-div = <64>;
 		reg = <0x01c4>;
 		ti,index-power-of-two;
 	};
 
-	clkoutmux0_clk_mux: clkoutmux0_clk_mux@158 {
+	clkoutmux0_clk_mux: clock-clkoutmux0-clk-mux@158 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkoutmux0_clk_mux";
 		clocks = <&sys_clk1_dclk_div>, <&sys_clk2_dclk_div>, <&per_abe_x1_dclk_div>, <&mpu_dclk_div>, <&dsp_gclk_div>, <&iva_dclk>, <&gpu_dclk>, <&core_dpll_out_dclk_div>, <&emif_phy_dclk_div>, <&gmac_250m_dclk_div>, <&video2_dclk_div>, <&video1_dclk_div>, <&hdmi_dclk_div>, <&func_96m_aon_dclk_div>, <&l3init_480m_dclk_div>, <&usb_otg_dclk_div>, <&sata_dclk_div>, <&pcie2_dclk_div>, <&pcie_dclk_div>, <&emu_dclk_div>, <&secure_32k_dclk_div>, <&eve_dclk_div>;
 		reg = <0x0158>;
 	};
 
-	clkoutmux1_clk_mux: clkoutmux1_clk_mux@15c {
+	clkoutmux1_clk_mux: clock-clkoutmux1-clk-mux@15c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkoutmux1_clk_mux";
 		clocks = <&sys_clk1_dclk_div>, <&sys_clk2_dclk_div>, <&per_abe_x1_dclk_div>, <&mpu_dclk_div>, <&dsp_gclk_div>, <&iva_dclk>, <&gpu_dclk>, <&core_dpll_out_dclk_div>, <&emif_phy_dclk_div>, <&gmac_250m_dclk_div>, <&video2_dclk_div>, <&video1_dclk_div>, <&hdmi_dclk_div>, <&func_96m_aon_dclk_div>, <&l3init_480m_dclk_div>, <&usb_otg_dclk_div>, <&sata_dclk_div>, <&pcie2_dclk_div>, <&pcie_dclk_div>, <&emu_dclk_div>, <&secure_32k_dclk_div>, <&eve_dclk_div>;
 		reg = <0x015c>;
 	};
 
-	clkoutmux2_clk_mux: clkoutmux2_clk_mux@160 {
+	clkoutmux2_clk_mux: clock-clkoutmux2-clk-mux@160 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkoutmux2_clk_mux";
 		clocks = <&sys_clk1_dclk_div>, <&sys_clk2_dclk_div>, <&per_abe_x1_dclk_div>, <&mpu_dclk_div>, <&dsp_gclk_div>, <&iva_dclk>, <&gpu_dclk>, <&core_dpll_out_dclk_div>, <&emif_phy_dclk_div>, <&gmac_250m_dclk_div>, <&video2_dclk_div>, <&video1_dclk_div>, <&hdmi_dclk_div>, <&func_96m_aon_dclk_div>, <&l3init_480m_dclk_div>, <&usb_otg_dclk_div>, <&sata_dclk_div>, <&pcie2_dclk_div>, <&pcie_dclk_div>, <&emu_dclk_div>, <&secure_32k_dclk_div>, <&eve_dclk_div>;
 		reg = <0x0160>;
 	};
 
-	custefuse_sys_gfclk_div: custefuse_sys_gfclk_div {
+	custefuse_sys_gfclk_div: clock-custefuse-sys-gfclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "custefuse_sys_gfclk_div";
 		clocks = <&sys_clkin1>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	eve_clk: eve_clk@180 {
+	eve_clk: clock-eve@180 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "eve_clk";
 		clocks = <&dpll_eve_m2_ck>, <&dpll_dsp_m3x2_ck>;
 		reg = <0x0180>;
 	};
 
-	hdmi_dpll_clk_mux: hdmi_dpll_clk_mux@164 {
+	hdmi_dpll_clk_mux: clock-hdmi-dpll-clk-mux@164 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "hdmi_dpll_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x0164>;
 	};
 
-	mlb_clk: mlb_clk@134 {
+	mlb_clk: clock-mlb@134 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "mlb_clk";
 		clocks = <&mlb_clkin_ck>;
 		ti,max-div = <64>;
 		reg = <0x0134>;
 		ti,index-power-of-two;
 	};
 
-	mlbp_clk: mlbp_clk@130 {
+	mlbp_clk: clock-mlbp@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "mlbp_clk";
 		clocks = <&mlbp_clkin_ck>;
 		ti,max-div = <64>;
 		reg = <0x0130>;
 		ti,index-power-of-two;
 	};
 
-	per_abe_x1_gfclk2_div: per_abe_x1_gfclk2_div@138 {
+	per_abe_x1_gfclk2_div: clock-per-abe-x1-gfclk2-div@138 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "per_abe_x1_gfclk2_div";
 		clocks = <&dpll_abe_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x0138>;
 		ti,index-power-of-two;
 	};
 
-	timer_sys_clk_div: timer_sys_clk_div@144 {
+	timer_sys_clk_div: clock-timer-sys-clk-div@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "timer_sys_clk_div";
 		clocks = <&sys_clkin1>;
 		reg = <0x0144>;
 		ti,max-div = <2>;
 	};
 
-	video1_dpll_clk_mux: video1_dpll_clk_mux@168 {
+	video1_dpll_clk_mux: clock-video1-dpll-clk-mux@168 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "video1_dpll_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x0168>;
 	};
 
-	video2_dpll_clk_mux: video2_dpll_clk_mux@16c {
+	video2_dpll_clk_mux: clock-video2-dpll-clk-mux@16c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "video2_dpll_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x016c>;
 	};
 
-	wkupaon_iclk_mux: wkupaon_iclk_mux@108 {
+	wkupaon_iclk_mux: clock-wkupaon-iclk-mux@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wkupaon_iclk_mux";
 		clocks = <&sys_clkin1>, <&abe_lp_clk_div>;
 		reg = <0x0108>;
 	};
 };
 
 &cm_core_clocks {
-	dpll_pcie_ref_ck: dpll_pcie_ref_ck@200 {
+	dpll_pcie_ref_ck: clock@200 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_pcie_ref_ck";
 		clocks = <&sys_clkin1>, <&sys_clkin1>;
 		reg = <0x0200>, <0x0204>, <0x020c>, <0x0208>;
 	};
 
-	dpll_pcie_ref_m2ldo_ck: dpll_pcie_ref_m2ldo_ck@210 {
+	dpll_pcie_ref_m2ldo_ck: clock-dpll-pcie-ref-m2ldo-8@210 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_pcie_ref_m2ldo_ck";
 		clocks = <&dpll_pcie_ref_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -1142,23 +1271,26 @@
 		ti,invert-autoidle-bit;
 	};
 
-	apll_pcie_in_clk_mux: apll_pcie_in_clk_mux@4ae06118 {
+	apll_pcie_in_clk_mux: clock-apll-pcie-in-clk-mux-7@4ae06118 {
 		compatible = "ti,mux-clock";
+		clock-output-names = "apll_pcie_in_clk_mux";
 		clocks = <&dpll_pcie_ref_m2ldo_ck>, <&pciesref_acs_clk_ck>;
 		#clock-cells = <0>;
 		reg = <0x021c 0x4>;
 		ti,bit-shift = <7>;
 	};
 
-	apll_pcie_ck: apll_pcie_ck@21c {
+	apll_pcie_ck: clock@21c {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-apll-clock";
+		clock-output-names = "apll_pcie_ck";
 		clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>;
 		reg = <0x021c>, <0x0220>;
 	};
 
-	optfclk_pciephy_div: optfclk_pciephy_div@4a00821c {
+	optfclk_pciephy_div: clock-optfclk-pciephy-div-8@4a00821c {
 		compatible = "ti,divider-clock";
+		clock-output-names = "optfclk_pciephy_div";
 		clocks = <&apll_pcie_ck>;
 		#clock-cells = <0>;
 		reg = <0x021c>;
@@ -1167,48 +1299,54 @@
 		ti,max-div = <2>;
 	};
 
-	apll_pcie_clkvcoldo: apll_pcie_clkvcoldo {
+	apll_pcie_clkvcoldo: clock-apll-pcie-clkvcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "apll_pcie_clkvcoldo";
 		clocks = <&apll_pcie_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	apll_pcie_clkvcoldo_div: apll_pcie_clkvcoldo_div {
+	apll_pcie_clkvcoldo_div: clock-apll-pcie-clkvcoldo-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "apll_pcie_clkvcoldo_div";
 		clocks = <&apll_pcie_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	apll_pcie_m2_ck: apll_pcie_m2_ck {
+	apll_pcie_m2_ck: clock-apll-pcie-m2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "apll_pcie_m2_ck";
 		clocks = <&apll_pcie_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_per_byp_mux: dpll_per_byp_mux@14c {
+	dpll_per_byp_mux: clock-dpll-per-byp-mux-23@14c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_per_byp_mux";
 		clocks = <&sys_clkin1>, <&per_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x014c>;
 	};
 
-	dpll_per_ck: dpll_per_ck@140 {
+	dpll_per_ck: clock@140 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin1>, <&dpll_per_byp_mux>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck@150 {
+	dpll_per_m2_ck: clock-dpll-per-m2-8@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -1217,32 +1355,36 @@
 		ti,invert-autoidle-bit;
 	};
 
-	func_96m_aon_dclk_div: func_96m_aon_dclk_div {
+	func_96m_aon_dclk_div: clock-func-96m-aon-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_96m_aon_dclk_div";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_usb_byp_mux: dpll_usb_byp_mux@18c {
+	dpll_usb_byp_mux: clock-dpll-usb-byp-mux-23@18c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_usb_byp_mux";
 		clocks = <&sys_clkin1>, <&usb_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x018c>;
 	};
 
-	dpll_usb_ck: dpll_usb_ck@180 {
+	dpll_usb_ck: clock@180 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
+		clock-output-names = "dpll_usb_ck";
 		clocks = <&sys_clkin1>, <&dpll_usb_byp_mux>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
 
-	dpll_usb_m2_ck: dpll_usb_m2_ck@190 {
+	dpll_usb_m2_ck: clock-dpll-usb-m2-8@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_usb_m2_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -1251,9 +1393,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_pcie_ref_m2_ck: dpll_pcie_ref_m2_ck@210 {
+	dpll_pcie_ref_m2_ck: clock-dpll-pcie-ref-m2-8@210 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_pcie_ref_m2_ck";
 		clocks = <&dpll_pcie_ref_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -1262,15 +1405,17 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_x2_ck: dpll_per_x2_ck {
+	dpll_per_x2_ck: clock-dpll-per-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_per_x2_ck";
 		clocks = <&dpll_per_ck>;
 	};
 
-	dpll_per_h11x2_ck: dpll_per_h11x2_ck@158 {
+	dpll_per_h11x2_ck: clock-dpll-per-h11x2-8@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h11x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1279,9 +1424,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_h12x2_ck: dpll_per_h12x2_ck@15c {
+	dpll_per_h12x2_ck: clock-dpll-per-h12x2-8@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h12x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1290,9 +1436,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_h13x2_ck: dpll_per_h13x2_ck@160 {
+	dpll_per_h13x2_ck: clock-dpll-per-h13x2-8@160 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h13x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1301,9 +1448,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_h14x2_ck: dpll_per_h14x2_ck@164 {
+	dpll_per_h14x2_ck: clock-dpll-per-h14x2-8@164 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h14x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1312,9 +1460,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_m2x2_ck: dpll_per_m2x2_ck@150 {
+	dpll_per_m2x2_ck: clock-dpll-per-m2x2-8@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -1323,105 +1472,118 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_usb_clkdcoldo: dpll_usb_clkdcoldo {
+	dpll_usb_clkdcoldo: clock-dpll-usb-clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_usb_clkdcoldo";
 		clocks = <&dpll_usb_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	func_128m_clk: func_128m_clk {
+	func_128m_clk: clock-func-128m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_128m_clk";
 		clocks = <&dpll_per_h11x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	func_12m_fclk: func_12m_fclk {
+	func_12m_fclk: clock-func-12m-fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
 	};
 
-	func_24m_clk: func_24m_clk {
+	func_24m_clk: clock-func-24m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	func_48m_fclk: func_48m_fclk {
+	func_48m_fclk: clock-func-48m-fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_48m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	func_96m_fclk: func_96m_fclk {
+	func_96m_fclk: clock-func-96m-fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_96m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l3init_60m_fclk: l3init_60m_fclk@104 {
+	l3init_60m_fclk: clock-l3init-60m@104 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3init_60m_fclk";
 		clocks = <&dpll_usb_m2_ck>;
 		reg = <0x0104>;
 		ti,dividers = <1>, <8>;
 	};
 
-	clkout2_clk: clkout2_clk@6b0 {
+	clkout2_clk: clock-clkout2-8@6b0 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "clkout2_clk";
 		clocks = <&clkoutmux2_clk_mux>;
 		ti,bit-shift = <8>;
 		reg = <0x06b0>;
 	};
 
-	l3init_960m_gfclk: l3init_960m_gfclk@6c0 {
+	l3init_960m_gfclk: clock-l3init-960m-gfclk-8@6c0 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "l3init_960m_gfclk";
 		clocks = <&dpll_usb_clkdcoldo>;
 		ti,bit-shift = <8>;
 		reg = <0x06c0>;
 	};
 
-	usb_phy1_always_on_clk32k: usb_phy1_always_on_clk32k@640 {
+	usb_phy1_always_on_clk32k: clock-usb-phy1-always-on-clk32k-8@640 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy1_always_on_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0640>;
 	};
 
-	usb_phy2_always_on_clk32k: usb_phy2_always_on_clk32k@688 {
+	usb_phy2_always_on_clk32k: clock-usb-phy2-always-on-clk32k-8@688 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy2_always_on_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0688>;
 	};
 
-	usb_phy3_always_on_clk32k: usb_phy3_always_on_clk32k@698 {
+	usb_phy3_always_on_clk32k: clock-usb-phy3-always-on-clk32k-8@698 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy3_always_on_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0698>;
 	};
 
-	gpu_core_gclk_mux: gpu_core_gclk_mux@1220 {
+	gpu_core_gclk_mux: clock-gpu-core-gclk-mux-24@1220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_core_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>, <&dpll_gpu_m2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1220>;
@@ -1429,9 +1591,10 @@
 		assigned-clock-parents = <&dpll_gpu_m2_ck>;
 	};
 
-	gpu_hyd_gclk_mux: gpu_hyd_gclk_mux@1220 {
+	gpu_hyd_gclk_mux: clock-gpu-hyd-gclk-mux-26@1220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_hyd_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>, <&dpll_gpu_m2_ck>;
 		ti,bit-shift = <26>;
 		reg = <0x1220>;
@@ -1439,34 +1602,38 @@
 		assigned-clock-parents = <&dpll_gpu_m2_ck>;
 	};
 
-	l3instr_ts_gclk_div: l3instr_ts_gclk_div@e50 {
+	l3instr_ts_gclk_div: clock-l3instr-ts-gclk-div-24@e50 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3instr_ts_gclk_div";
 		clocks = <&wkupaon_iclk_mux>;
 		ti,bit-shift = <24>;
 		reg = <0x0e50>;
 		ti,dividers = <8>, <16>, <32>;
 	};
 
-	vip1_gclk_mux: vip1_gclk_mux@1020 {
+	vip1_gclk_mux: clock-vip1-gclk-mux-24@1020 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "vip1_gclk_mux";
 		clocks = <&l3_iclk_div>, <&dpll_core_h23x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1020>;
 	};
 
-	vip2_gclk_mux: vip2_gclk_mux@1028 {
+	vip2_gclk_mux: clock-vip2-gclk-mux-24@1028 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "vip2_gclk_mux";
 		clocks = <&l3_iclk_div>, <&dpll_core_h23x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1028>;
 	};
 
-	vip3_gclk_mux: vip3_gclk_mux@1030 {
+	vip3_gclk_mux: clock-vip3-gclk-mux-24@1030 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "vip3_gclk_mux";
 		clocks = <&l3_iclk_div>, <&dpll_core_h23x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1030>;
@@ -1474,48 +1641,54 @@
 };
 
 &cm_core_clockdomains {
-	coreaon_clkdm: coreaon_clkdm {
+	coreaon_clkdm: clock-coreaon-clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "coreaon_clkdm";
 		clocks = <&dpll_usb_ck>;
 	};
 };
 
 &scm_conf_clocks {
-	dss_deshdcp_clk: dss_deshdcp_clk@558 {
+	dss_deshdcp_clk: clock-dss-deshdcp-0@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "dss_deshdcp_clk";
 		clocks = <&l3_iclk_div>;
 		ti,bit-shift = <0>;
 		reg = <0x558>;
 	};
 
-       ehrpwm0_tbclk: ehrpwm0_tbclk@558 {
+       ehrpwm0_tbclk: clock-ehrpwm0-tbclk-20@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm0_tbclk";
 		clocks = <&l4_root_clk_div>;
 		ti,bit-shift = <20>;
 		reg = <0x0558>;
 	};
 
-	ehrpwm1_tbclk: ehrpwm1_tbclk@558 {
+	ehrpwm1_tbclk: clock-ehrpwm1-tbclk-21@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm1_tbclk";
 		clocks = <&l4_root_clk_div>;
 		ti,bit-shift = <21>;
 		reg = <0x0558>;
 	};
 
-	ehrpwm2_tbclk: ehrpwm2_tbclk@558 {
+	ehrpwm2_tbclk: clock-ehrpwm2-tbclk-22@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm2_tbclk";
 		clocks = <&l4_root_clk_div>;
 		ti,bit-shift = <22>;
 		reg = <0x0558>;
 	};
 
-	sys_32k_ck: sys_32k_ck {
+	sys_32k_ck: clock-sys-32k {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_32k_ck";
 		clocks = <&sys_clk32_crystal_ck>, <&sys_clk32_pseudo_ck>, <&sys_clk32_pseudo_ck>, <&sys_clk32_pseudo_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x6c4>;
@@ -1523,253 +1696,354 @@
 };
 
 &cm_core_aon {
-	mpu_cm: mpu-cm@300 {
+	mpu_cm: clock@300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x300 0x100>;
 
-		mpu_clkctrl: mpu-clkctrl@20 {
+		mpu_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	dsp1_cm: dsp1-cm@400 {
+	dsp1_cm: clock@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dsp1_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x400 0x100>;
 
-		dsp1_clkctrl: dsp1-clkctrl@20 {
+		dsp1_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dsp1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	ipu_cm: ipu-cm@500 {
+	ipu_cm: clock@500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ipu_cm";
 		reg = <0x500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x500 0x100>;
 
-		ipu1_clkctrl: ipu1-clkctrl@20 {
+		ipu1_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
+			assigned-clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 24>;
+			assigned-clock-parents = <&dpll_core_h22x2_ck>;
 		};
 
-		ipu_clkctrl: ipu-clkctrl@50 {
+		ipu_clkctrl: clock@50 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu_clkctrl";
 			reg = <0x50 0x34>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	dsp2_cm: dsp2-cm@600 {
+	dsp2_cm: clock@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dsp2_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x600 0x100>;
 
-		dsp2_clkctrl: dsp2-clkctrl@20 {
+		dsp2_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dsp2_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	rtc_cm: rtc-cm@700 {
+	rtc_cm: clock@700 {
 		compatible = "ti,omap4-cm";
-		reg = <0x700 0x100>;
+		clock-output-names = "rtc_cm";
+		reg = <0x700 0x60>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0 0x700 0x100>;
+		ranges = <0 0x700 0x60>;
 
-		rtc_clkctrl: rtc-clkctrl@20 {
+		rtc_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "rtc_clkctrl";
 			reg = <0x20 0x28>;
 			#clock-cells = <2>;
 		};
 	};
 
+	vpe_cm: clock@760 {
+		compatible = "ti,omap4-cm";
+		clock-output-names = "vpe_cm";
+		reg = <0x760 0xc>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x760 0xc>;
+
+		vpe_clkctrl: clock@0 {
+			compatible = "ti,clkctrl";
+			clock-output-names = "vpe_clkctrl";
+			reg = <0x0 0xc>;
+			#clock-cells = <2>;
+		};
+	};
+
 };
 
 &cm_core {
-	coreaon_cm: coreaon-cm@600 {
+	coreaon_cm: clock@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "coreaon_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x600 0x100>;
 
-		coreaon_clkctrl: coreaon-clkctrl@20 {
+		coreaon_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "coreaon_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l3main1_cm: l3main1-cm@700 {
+	l3main1_cm: clock@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3main1_cm";
 		reg = <0x700 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x700 0x100>;
 
-		l3main1_clkctrl: l3main1-clkctrl@20 {
+		l3main1_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3main1_clkctrl";
 			reg = <0x20 0x74>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	ipu2_cm: ipu2-cm@900 {
+	ipu2_cm: clock@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ipu2_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x900 0x100>;
 
-		ipu2_clkctrl: ipu2-clkctrl@20 {
+		ipu2_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu2_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	dma_cm: dma-cm@a00 {
+	dma_cm: clock@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dma_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xa00 0x100>;
 
-		dma_clkctrl: dma-clkctrl@20 {
+		dma_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dma_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	emif_cm: emif-cm@b00 {
+	emif_cm: clock@b00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "emif_cm";
 		reg = <0xb00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xb00 0x100>;
 
-		emif_clkctrl: emif-clkctrl@20 {
+		emif_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emif_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	atl_cm: atl-cm@c00 {
+	atl_cm: clock@c00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "atl_cm";
 		reg = <0xc00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xc00 0x100>;
 
-		atl_clkctrl: atl-clkctrl@0 {
+		atl_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "atl_clkctrl";
 			reg = <0x0 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4cfg_cm: l4cfg-cm@d00 {
+	l4cfg_cm: clock@d00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4cfg_cm";
 		reg = <0xd00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xd00 0x100>;
 
-		l4cfg_clkctrl: l4cfg-clkctrl@20 {
+		l4cfg_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4cfg_clkctrl";
 			reg = <0x20 0x84>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l3instr_cm: l3instr-cm@e00 {
+	l3instr_cm: clock@e00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3instr_cm";
 		reg = <0xe00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xe00 0x100>;
 
-		l3instr_clkctrl: l3instr-clkctrl@20 {
+		l3instr_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3instr_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
 	};
 
-	dss_cm: dss-cm@1100 {
+	iva_cm: clock@f00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "iva_cm";
+		reg = <0xf00 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xf00 0x100>;
+
+		iva_clkctrl: clock@20 {
+			compatible = "ti,clkctrl";
+			clock-output-names = "iva_clkctrl";
+			reg = <0x20 0xc>;
+			#clock-cells = <2>;
+		};
+	};
+
+	cam_cm: clock@1000 {
+		compatible = "ti,omap4-cm";
+		clock-output-names = "cam_cm";
+		reg = <0x1000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x1000 0x100>;
+
+		cam_clkctrl: clock@20 {
+			compatible = "ti,clkctrl";
+			clock-output-names = "cam_clkctrl";
+			reg = <0x20 0x2c>;
+			#clock-cells = <2>;
+		};
+	};
+
+	dss_cm: clock@1100 {
+		compatible = "ti,omap4-cm";
+		clock-output-names = "dss_cm";
 		reg = <0x1100 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1100 0x100>;
 
-		dss_clkctrl: dss-clkctrl@20 {
+		dss_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dss_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l3init_cm: l3init-cm@1300 {
+	gpu_cm: clock@1200 {
+		compatible = "ti,omap4-cm";
+		clock-output-names = "gpu_cm";
+		reg = <0x1200 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x1200 0x100>;
+
+		gpu_clkctrl: clock@20 {
+			compatible = "ti,clkctrl";
+			clock-output-names = "gpu_clkctrl";
+			reg = <0x20 0x4>;
+			#clock-cells = <2>;
+		};
+	};
+
+	l3init_cm: clock@1300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3init_cm";
 		reg = <0x1300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1300 0x100>;
 
-		l3init_clkctrl: l3init-clkctrl@20 {
+		l3init_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3init_clkctrl";
 			reg = <0x20 0x6c>, <0xe0 0x14>;
 			#clock-cells = <2>;
 		};
 
-		pcie_clkctrl: pcie-clkctrl@b0 {
+		pcie_clkctrl: clock@b0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "pcie_clkctrl";
 			reg = <0xb0 0xc>;
 			#clock-cells = <2>;
 		};
 
-		gmac_clkctrl: gmac-clkctrl@d0 {
+		gmac_clkctrl: clock@d0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gmac_clkctrl";
 			reg = <0xd0 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	l4per_cm: l4per-cm@1700 {
+	l4per_cm: clock@1700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4per_cm";
 		reg = <0x1700 0x300>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1700 0x300>;
 
-		l4per_clkctrl: l4per-clkctrl@28 {
+		l4per_clkctrl: clock@28 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per_clkctrl";
 			reg = <0x28 0x64>, <0xa0 0x24>, <0xf0 0x3c>, <0x140 0x1c>, <0x170 0x4>;
 			#clock-cells = <2>;
 
@@ -1777,20 +2051,23 @@
 			assigned-clock-parents = <&abe_24m_fclk>;
 		};
 
-		l4sec_clkctrl: l4sec-clkctrl@1a0 {
+		l4sec_clkctrl: clock@1a0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4sec_clkctrl";
 			reg = <0x1a0 0x2c>;
 			#clock-cells = <2>;
 		};
 
-		l4per2_clkctrl: l4per2-clkctrl@c {
+		l4per2_clkctrl: clock@c {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per2_clkctrl";
 			reg = <0xc 0x4>, <0x18 0xc>, <0x90 0xc>, <0xc4 0x4>, <0x138 0x4>, <0x160 0xc>, <0x178 0x24>, <0x1d0 0x3c>;
 			#clock-cells = <2>;
 		};
 
-		l4per3_clkctrl: l4per3-clkctrl@14 {
+		l4per3_clkctrl: clock@14 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per3_clkctrl";
 			reg = <0x14 0x4>, <0xc8 0x14>, <0x130 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1799,15 +2076,17 @@
 };
 
 &prm {
-	wkupaon_cm: wkupaon-cm@1800 {
+	wkupaon_cm: clock@1800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkupaon_cm";
 		reg = <0x1800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1800 0x100>;
 
-		wkupaon_clkctrl: wkupaon-clkctrl@20 {
+		wkupaon_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "wkupaon_clkctrl";
 			reg = <0x20 0x6c>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/elpida_ecb240abacn.dtsi b/arch/arm/boot/dts/ti/omap/elpida_ecb240abacn.dtsi
index d87ee4794f83..9698801cbcfb 100644
--- a/arch/arm/boot/dts/elpida_ecb240abacn.dtsi
+++ b/arch/arm/boot/dts/ti/omap/elpida_ecb240abacn.dtsi
@@ -5,7 +5,7 @@
 
 / {
 	elpida_ECB240ABACN: lpddr2 {
-		compatible	= "Elpida,ECB240ABACN","jedec,lpddr2-s4";
+		compatible	= "elpida,ECB240ABACN","jedec,lpddr2-s4";
 		density		= <2048>;
 		io-width	= <32>;
 
diff --git a/arch/arm/boot/dts/ti/omap/logicpd-som-lv-35xx-devkit.dts b/arch/arm/boot/dts/ti/omap/logicpd-som-lv-35xx-devkit.dts
new file mode 100644
index 000000000000..c1705f6f3d10
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/logicpd-som-lv-35xx-devkit.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+#include "logicpd-som-lv.dtsi"
+#include "logicpd-som-lv-baseboard.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
+
+/ {
+	model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
+	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_2_pins>;
+	hsusb2_2_pins: hsusb2-2-pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/logicpd-som-lv-37xx-devkit.dts b/arch/arm/boot/dts/ti/omap/logicpd-som-lv-37xx-devkit.dts
new file mode 100644
index 000000000000..9dbbcc7ced7c
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/logicpd-som-lv-37xx-devkit.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "logicpd-som-lv.dtsi"
+#include "logicpd-som-lv-baseboard.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
+
+/ {
+	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
+	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_2_pins>;
+	hsusb2_2_pins: hsusb2-2-pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/boot/dts/ti/omap/logicpd-som-lv-baseboard.dtsi
index 100396f6c2fe..690f2ad50c65 100644
--- a/arch/arm/boot/dts/logicpd-som-lv-baseboard.dtsi
+++ b/arch/arm/boot/dts/ti/omap/logicpd-som-lv-baseboard.dtsi
@@ -51,6 +51,8 @@
 
 &mcbsp2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
 };
 
 &charger {
@@ -77,7 +79,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 	vdds_dsi-supply = <&vpll2>;
 	vdda_video-supply = <&video_reg>;
 	pinctrl-names = "default";
@@ -102,35 +104,18 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	lcd0: display@0 {
-		compatible = "panel-dpi";
-		label = "28";
-		status = "okay";
-		/* default-on; */
+	lcd0: display {
+		/* This isn't the exact LCD, but the timings meet spec */
+		compatible = "logicpd,type28";
 		pinctrl-names = "default";
 		pinctrl-0 = <&lcd_enable_pin>;
-		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
+		backlight = <&bl>;
+		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
 		port {
 			lcd_in: endpoint {
 				remote-endpoint = <&dpi_out>;
 			};
 		};
-
-		panel-timing {
-			clock-frequency = <9000000>;
-			hactive = <480>;
-			vactive = <272>;
-			hfront-porch = <3>;
-			hback-porch = <2>;
-			hsync-len = <42>;
-			vback-porch = <3>;
-			vfront-porch = <2>;
-			vsync-len = <11>;
-			hsync-active = <1>;
-			vsync-active = <1>;
-			de-active = <1>;
-			pixelclk-active = <0>;
-		};
 	};
 
 	bl: backlight {
@@ -156,25 +141,25 @@
 };
 
 &omap3_pmx_core {
-	gpio_key_pins: pinmux_gpio_key_pins {
+	gpio_key_pins: gpio-key-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_xclkb.gpio_111 / uP_GPIO_3*/
 		>;
 	};
 
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */
 		>;
 	};
 
-	lan9221_pins: pinmux_lan9221_pins {
+	lan9221_pins: lan9221-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -187,13 +172,13 @@
 		>;
 	};
 
-	lcd_enable_pin: pinmux_lcd_enable_pin {
+	lcd_enable_pin: lcd-enable-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
 		>;
 	};
 
-	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
+	dss_dpi_pins1: dss-dpi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -221,13 +206,13 @@
 };
 
 &omap3_pmx_wkup {
-	led_pins_wkup: pinmux_led_pins_wkup {
+	led_pins_wkup: led-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 / uP_GPIO_1 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* sys_boot6.gpio_8 */
 		>;
diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/ti/omap/logicpd-som-lv.dtsi
index b56524cc7fe2..c0e6b73fa472 100644
--- a/arch/arm/boot/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/boot/dts/ti/omap/logicpd-som-lv.dtsi
@@ -27,6 +27,8 @@
 
 	/* HS USB Host PHY on PORT 1 */
 	hsusb2_phy: hsusb2_phy {
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb2_reset_pin>;
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
 		#phy-cells = <0>;
@@ -144,6 +146,8 @@
 };
 
 &usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_pins>;
 	port2-mode = "ehci-phy";
 };
 
@@ -151,12 +155,9 @@
 	phys = <0 &hsusb2_phy>;
 };
 
-
 &omap3_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_pins>;
 
-	mmc3_pins: pinmux_mm3_pins {
+	mmc3_pins: mm3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
 			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
@@ -166,7 +167,7 @@
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
 		>;
 	};
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
 			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
@@ -174,7 +175,7 @@
 			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
 		>;
 	};
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)	/* uart2_cts.uart2_cts */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)	/* uart2_rts .uart2_rts*/
@@ -183,7 +184,7 @@
 			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* GPIO_162,BT_EN */
 		>;
 	};
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
@@ -192,7 +193,7 @@
 		>;
 	};
 
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi1_cs3.hsusb2_data2 */
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_clk.hsusb2_data7 */
@@ -203,7 +204,7 @@
 		>;
 	};
 
-	hsusb_otg_pins: pinmux_hsusb_otg_pins {
+	hsusb_otg_pins: hsusb-otg-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)	/* hsusb0_clk.hsusb0_clk */
 			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp.hsusb0_stp */
@@ -220,7 +221,7 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
@@ -228,21 +229,21 @@
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)	/* i2c2_scl */
 			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	tsc2004_pins: pinmux_tsc2004_pins {
+	tsc2004_pins: tsc2004-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4)	/* mcbsp4_dr.gpio_153 */
 		>;
@@ -250,14 +251,13 @@
 };
 
 &omap3_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_reset_pin>;
-	hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
+
+	hsusb2_reset_pin: hsusb1-reset-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
 		>;
 	};
-	wl127x_gpio: pinmux_wl127x_gpio_pin {
+	wl127x_gpio: wl127x-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
@@ -265,21 +265,6 @@
 	};
 };
 
-&omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_2_pins>;
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
-		pinctrl-single,pins = <
-			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
-			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
-			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
-			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
-			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
-			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
-		>;
-	};
-};
-
 &uart2 {
 	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-35xx-devkit.dts
index 57bae2aa910e..eaa583fdc3d6 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts
+++ b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-35xx-devkit.dts
@@ -11,3 +11,11 @@
 	model = "LogicPD Zoom OMAP35xx Torpedo Development Kit";
 	compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3430", "ti,omap3";
 };
+
+&omap3_pmx_core {
+	isp1763_pins: isp1763-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2154,  PIN_INPUT_PULLUP | MUX_MODE4)	/* sdmmc1_dat6.gpio_128 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-37xx-devkit-28.dts
index b5536132971f..b5536132971f 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts
+++ b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-37xx-devkit-28.dts
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-37xx-devkit.dts
index 5532db04046c..fbff15a0a0fe 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-37xx-devkit.dts
@@ -52,7 +52,7 @@
 
 &uart2 {
 	/delete-property/dma-names;
-	bluetooth {
+	bluetooth-gnss {
 		compatible = "ti,wl1283-st";
 		enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */
 		max-speed = <3000000>;
@@ -65,7 +65,7 @@
 };
 
 &omap3_pmx_core {
-	mmc3_pins: pinmux_mm3_pins {
+	mmc3_pins: mm3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
 			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
@@ -78,10 +78,19 @@
 };
 
 &omap3_pmx_core2 {
-	mmc3_core2_pins: pinmux_mmc3_core2_pins {
+	mmc3_core2_pins: mmc3-core2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_clk.sdmmc3_clk */
 			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_ctl.sdmmc3_cmd */
 		>;
 	};
 };
+
+/* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */
+&omap3_pmx_wkup {
+	isp1763_pins: isp1763-pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4)	/* reserved.gpio_128 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-baseboard.dtsi
index f7b82ced4080..e0caed539810 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi
+++ b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-baseboard.dtsi
@@ -59,12 +59,13 @@
 		};
 	};
 
-	pwm10: dmtimer-pwm {
+	pwm10: pwm-10 {
 		compatible = "ti,omap-dmtimer-pwm";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwm_pins>;
 		ti,timers = <&timer10>;
 		#pwm-cells = <3>;
+		ti,clock-source = <0x01>;
 	};
 
 };
@@ -80,6 +81,8 @@
 };
 
 &mcbsp2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
 	status = "okay";
 };
 
@@ -90,7 +93,8 @@
 
 &gpmc {
 	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
-		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+		  1 0 0x2c000000 0x1000000	/* CS1: 16MB for LAN9221 */
+		  6 0 0x28000000 0x1000000>;	/* CS6: 16MB for ISP1763 */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";
@@ -99,6 +103,44 @@
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;		/* gpio129 */
 		reg = <1 0 0xff>;
 	};
+
+	usb@6,0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&isp1763_pins>;
+		compatible = "nxp,usb-isp1763";
+		reg = <0x6 0x0 0xff>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "host";
+		bus-width = <16>;
+		dr_mode = "host";
+		gpmc,mux-add-data = <0>;
+		gpmc,device-width = <2>;
+		gpmc,wait-pin = <0>;
+		gpmc,burst-length = <4>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <45>;
+		gpmc,cs-wr-off-ns = <45>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <0>;
+		gpmc,adv-wr-off-ns = <0>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <45>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <25>;
+		gpmc,rd-cycle-ns = <60>;
+		gpmc,wr-cycle-ns = <45>;
+		gpmc,access-ns = <35>;
+		gpmc,page-burst-access-ns = <0>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <60>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wr-data-mux-bus-ns = <5>;
+		gpmc,wr-access-ns = <20>;
+	};
 };
 
 &hdqw1w {
@@ -112,7 +154,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 	vdds_dsi-supply = <&vpll2>;
 	vdda_video-supply = <&vpll2>;
 	pinctrl-names = "default";
@@ -167,33 +209,33 @@
 };
 
 &omap3_pmx_core {
-	gpio_key_pins: pinmux_gpio_key_pins {
+	gpio_key_pins: gpio-key-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcspi2_clk.gpio_178 */
 			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcspi2_cs0.gpio_181 */
 		>;
 	};
 
-	hdq_pins: hdq_pins {
+	hdq_pins: hdq-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0) /* hdq_sio */
 		>;
 	};
 
-	pwm_pins: pinmux_pwm_pins {
+	pwm_pins: pwm-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3)       /* gpmc_ncs5.gpt_10_pwm_evt */
 		>;
 	};
 
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4)	/* gpio_179 */
 			OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4)	/* gpio_180 */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -204,19 +246,19 @@
 		>;
 	};
 
-	tsc2004_pins: pinmux_tsc2004_pins {
+	tsc2004_pins: tsc2004-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4)	/* mcbsp4_dr.gpio_153 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_dx.gpio_154 */
 		>;
 	};
 
-	isp_pins: pinmux_isp_pins {
+	isp_pins: isp-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0)   /* cam_hs.cam_hs */
 			OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0)   /* cam_vs.cam_vs */
@@ -234,13 +276,13 @@
 		>;
 	};
 
-	panel_pwr_pins: pinmux_panel_pwr_pins {
+	panel_pwr_pins: panel-pwr-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
 		>;
 	};
 
-	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
+	dss_dpi_pins1: dss-dpi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -271,20 +313,20 @@
 };
 
 &omap3_pmx_wkup {
-	gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup {
+	gpio_key_pins_wkup: gpio-key-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_boot0.gpio_2 */
 			OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_boot5.gpio_7 */
 		>;
 	};
 
-	lan9221_pins: pinmux_lan9221_pins {
+	lan9221_pins: lan9221-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4)		/* reserved.gpio_129 */
 		>;
 	};
 
-	mmc1_cd: pinmux_mmc1_cd {
+	mmc1_cd: mmc1-cd-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4)	/* reserved.gpio_127 */
 		>;
diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-som.dtsi
index 3a5228562b0d..227699890890 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
+++ b/arch/arm/boot/dts/ti/omap/logicpd-torpedo-som.dtsi
@@ -20,7 +20,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		user0 {
+		led-user0 {
 			label = "user0";
 			gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;	/* LEDA */
 			linux,default-trigger = "none";
@@ -111,7 +111,7 @@
 };
 
 &omap3_pmx_core {
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
 			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
@@ -119,7 +119,7 @@
 			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
 		>;
 	};
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)	/* uart2_cts.uart2_cts */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)	/* uart2_rts .uart2_rts*/
@@ -128,7 +128,7 @@
 			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* GPIO_162,BT_EN */
 		>;
 	};
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
@@ -136,7 +136,7 @@
 			OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_cs0.mcspi1_cs0 */
 		>;
 	};
-	hsusb_otg_pins: pinmux_hsusb_otg_pins {
+	hsusb_otg_pins: hsusb-otg-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)	/* hsusb0_clk.hsusb0_clk */
 			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp.hsusb0_stp */
@@ -153,19 +153,19 @@
 			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
 		>;
 	};
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
 		>;
 	};
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)	/* i2c2_scl */
 			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda */
diff --git a/arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi b/arch/arm/boot/dts/ti/omap/motorola-cpcap-mapphone.dtsi
index 936ad010c83a..ea02fd403a9b 100644
--- a/arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi
+++ b/arch/arm/boot/dts/ti/omap/motorola-cpcap-mapphone.dtsi
@@ -13,8 +13,10 @@
 		#interrupt-cells = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		spi-max-frequency = <3000000>;
+		spi-max-frequency = <9600000>;
 		spi-cs-high;
+		spi-cpol;
+		spi-cpha;
 
 		cpcap_adc: adc {
 			compatible = "motorola,mapphone-cpcap-adc";
@@ -25,15 +27,14 @@
 
 		cpcap_battery: battery {
 			compatible = "motorola,cpcap-battery";
-			interrupts-extended = <
-				&cpcap 6 0 &cpcap 5 0 &cpcap 3 0
-				&cpcap 20 0 &cpcap 54 0
-			>;
+			interrupts-extended =
+				<&cpcap 6 0>, <&cpcap 5 0>, <&cpcap 3 0>,
+				<&cpcap 20 0>, <&cpcap 54 0>, <&cpcap 57 0>;
 			interrupt-names =
 				"eol", "lowbph", "lowbpl",
-				"chrgcurr1", "battdetb";
-			io-channels = <&cpcap_adc 0 &cpcap_adc 1
-				       &cpcap_adc 5 &cpcap_adc 6>;
+				"chrgcurr1", "battdetb", "cccal";
+			io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>,
+				      <&cpcap_adc 5>, <&cpcap_adc 6>;
 			io-channel-names = "battdetb", "battp",
 					   "chg_isense", "batti";
 			power-supplies = <&cpcap_charger>;
@@ -41,20 +42,19 @@
 
 		cpcap_charger: charger {
 			compatible = "motorola,mapphone-cpcap-charger";
-			interrupts-extended = <
-				&cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0
-				&cpcap 22 0 &cpcap 21 0 &cpcap 20 0 &cpcap 19 0
-				&cpcap 54 0
-			>;
+			interrupts-extended =
+				<&cpcap 13 0>, <&cpcap 12 0>, <&cpcap 29 0>,
+				<&cpcap 28 0>, <&cpcap 22 0>, <&cpcap 21 0>,
+				<&cpcap 20 0>, <&cpcap 19 0>, <&cpcap 54 0>;
 			interrupt-names =
-				"chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn",
-				"rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld",
-				"battdetb";
-			mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW
-				      &gpio3 23 GPIO_ACTIVE_LOW>;
-			io-channels = <&cpcap_adc 0 &cpcap_adc 1
-				       &cpcap_adc 2 &cpcap_adc 5
-				       &cpcap_adc 6>;
+				"chrg_det", "rvrs_chrg", "chrg_se1b",
+				"se0conn", "rvrs_mode", "chrgcurr2",
+				"chrgcurr1", "vbusvld", "battdetb";
+			mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>,
+				     <&gpio3 23 GPIO_ACTIVE_LOW>;
+			io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>,
+				      <&cpcap_adc 2>, <&cpcap_adc 5>,
+				      <&cpcap_adc 6>;
 			io-channel-names = "battdetb", "battp",
 					   "vbus", "chg_isense",
 					   "batti";
@@ -95,22 +95,22 @@
 
 		cpcap_usb2_phy: phy {
 			compatible = "motorola,mapphone-cpcap-usb-phy";
-			pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>;
+			pinctrl-0 = <&usb_gpio_mux_sel1>, <&usb_gpio_mux_sel2>;
 			pinctrl-1 = <&usb_ulpi_pins>;
 			pinctrl-2 = <&usb_utmi_pins>;
 			pinctrl-3 = <&uart3_pins>;
 			pinctrl-names = "default", "ulpi", "utmi", "uart";
 			#phy-cells = <0>;
-			interrupts-extended = <
-				&cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0
-				&cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0
-				&cpcap 48 0
-			>;
+			interrupts-extended =
+				<&cpcap 15 0>, <&cpcap 14 0>, <&cpcap 28 0>,
+				<&cpcap 19 0>, <&cpcap 18 0>, <&cpcap 17 0>,
+				<&cpcap 16 0>, <&cpcap 49 0>, <&cpcap 48 0>;
 			interrupt-names =
-				"id_ground", "id_float", "se0conn", "vbusvld",
-				"sessvld", "sessend", "se1", "dm", "dp";
-			mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH
-				      &gpio1 0 GPIO_ACTIVE_HIGH>;
+				"id_ground", "id_float", "se0conn",
+				"vbusvld", "sessvld", "sessend",
+				"se1", "dm", "dp";
+			mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>,
+				     <&gpio1 0 GPIO_ACTIVE_HIGH>;
 			io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>;
 			io-channel-names = "vbus", "id";
 			vusb-supply = <&vusb>;
diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi
new file mode 100644
index 000000000000..a0c53d9c2625
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi
@@ -0,0 +1,458 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "omap443x.dtsi"
+#include "motorola-cpcap-mapphone.dtsi"
+
+/ {
+	/*
+	 * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
+	 * then 1023 - 1024 seems to contain mbm.
+	 */
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x3fd00000>;	/* 1021 MB */
+	};
+
+	/* Poweroff GPIO probably connected to CPCAP */
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&poweroff_gpio>;
+		pinctrl-names = "default";
+		gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;	/* gpio50 */
+	};
+
+	hdmi0: connector {
+		compatible = "hdmi-connector";
+		pinctrl-0 = <&hdmi_hpd_gpio>;
+		pinctrl-names = "default";
+		label = "hdmi";
+		type = "d";
+
+		hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;	/* gpio63 */
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	/*
+	 * HDMI 5V regulator probably sourced from battery. Let's keep
+	 * keep this as always enabled for HDMI to work until we've
+	 * figured what the encoder chip is.
+	 */
+	hdmi_regulator: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;	/* gpio59 */
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	/* This is probably coming straight from the battery.. */
+	wl12xx_vmmc: regulator-wl12xx {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1650000>;
+		regulator-max-microvolt = <1650000>;
+		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;	/* gpio94 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	soundcard {
+		compatible = "audio-graph-card";
+		label = "Mapphone Audio";
+
+		widgets =
+			"Speaker", "Earpiece",
+			"Speaker", "Loudspeaker",
+			"Headphone", "Headphone Jack",
+			"Microphone", "Internal Mic";
+
+		routing =
+			"Earpiece", "EP",
+			"Loudspeaker", "SPKR",
+			"Headphone Jack", "HSL",
+			"Headphone Jack", "HSR",
+			"MICR", "Internal Mic";
+
+		dais = <&mcbsp2_port>, <&mcbsp3_port>;
+	};
+};
+
+&cpu_thermal {
+	polling-delay = <10000>; /* milliseconds */
+};
+
+&cpu_alert0 {
+        temperature = <80000>; /* millicelsius */
+};
+
+&cpu0 {
+        /*
+	 * Note that the 1.2GiHz mode is enabled for all SoC variants for
+	 * the Motorola Android Linux v3.0.8 based kernel.
+	 */
+        operating-points = <
+	        /* kHz    uV */
+	        300000  1025000
+	        600000  1200000
+	        800000  1313000
+	        1008000 1375000
+		1200000 1375000
+        >;
+};
+
+&dss {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+	pinctrl-0 = <&dss_hdmi_pins>;
+	pinctrl-names = "default";
+	vdda-supply = <&vdac>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&hdmi_connector_in>;
+			lanes = <1 0 3 2 5 4 7 6>;
+		};
+	};
+};
+
+&i2c1 {
+	tmp105@48 {
+		compatible = "ti,tmp105";
+		reg = <0x48>;
+		pinctrl-0 = <&tmp105_irq>;
+		pinctrl-names = "default";
+		/* kpd_row0.gpio_178 */
+		interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
+				       &omap4_pmx_core 0x14e>;
+		interrupt-names = "irq", "wakeup";
+		wakeup-source;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&vwlan2>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;	/* gpio176 */
+};
+
+&mmc2 {
+	vmmc-supply = <&vsdio>;
+	bus-width = <8>;
+	ti,non-removable;
+};
+
+&mmc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins>;
+	vmmc-supply = <&wl12xx_vmmc>;
+	/* uart2_tx.sdmmc3_dat1 pad as wakeirq */
+	interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core 0xde>;
+	interrupt-names = "irq", "wakeup";
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1285";
+		reg = <2>;
+		/* gpio_100 with gpmc_wait2 pad as wakeirq */
+		interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
+				      <&omap4_pmx_core 0x4e>;
+		interrupt-names = "irq", "wakeup";
+		ref-clock-frequency = <26000000>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
+
+&omap4_pmx_core {
+
+	/* hdmi_hpd.gpio_63 */
+	hdmi_hpd_gpio: hdmi-hpd-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
+		>;
+	};
+
+	/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
+	dss_hdmi_pins: dss-hdmi-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
+		OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
+		OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
+		>;
+	};
+
+	/*
+	 * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
+	 * for gpio_100, but the internal pull makes wlan flakey on some
+	 * devices. Off mode value should be tested if we have off mode working
+	 * later on.
+	 */
+	mmc3_pins: mmc3-pins {
+		pinctrl-single,pins = <
+		/* 0x4a10008e gpmc_wait2.gpio_100 d23 */
+		OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
+
+		/* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
+		OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
+		OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
+		OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
+
+		/* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
+		OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
+		OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
+		OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
+		>;
+	};
+
+	/* gpmc_ncs0.gpio_50 */
+	poweroff_gpio: poweroff-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	/* kpd_row0.gpio_178 */
+	tmp105_irq: tmp105-irq-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	usb_gpio_mux_sel1: usb-gpio-mux-sel1-pins {
+		/* gpio_60 */
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
+		>;
+	};
+
+	usb_ulpi_pins: usb-ulpi-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x196, MUX_MODE7)
+		OMAP4_IOPAD(0x198, MUX_MODE7)
+		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
+		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
+		>;
+	};
+
+	/* usb0_otg_dp and usb0_otg_dm */
+	usb_utmi_pins: usb-utmi-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
+		OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
+		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
+		>;
+	};
+
+	/*
+	 * Note that the v3.0.8 stock userspace dynamically remuxes uart1
+	 * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
+	 * when not used. If needed, we can add rts pin remux later based
+	 * on power measurements.
+	 */
+	uart1_pins: uart1-pins {
+		pinctrl-single,pins = <
+		/* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
+		OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
+		OMAP4_IOPAD(0x13e, MUX_MODE1)
+
+		/* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
+		OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
+
+		/* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
+		OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
+		>;
+	};
+
+	/* uart3_tx_irtx and uart3_rx_irrx */
+	uart3_pins: uart3-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x196, MUX_MODE7)
+		OMAP4_IOPAD(0x198, MUX_MODE7)
+		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1ba, MUX_MODE2)
+		OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
+		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
+		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
+		>;
+	};
+
+	uart4_pins: uart4-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)		/* uart4_rx */
+		OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)		/* uart4_tx */
+		OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)	/* uart4_cts */
+		OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)	/* uart4_rts */
+		>;
+	};
+
+	mcbsp2_pins: mcbsp2-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_clkx */
+		OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_dr */
+		OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)	/* abe_mcbsp2_dx */
+		OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_fsx */
+		>;
+	};
+
+	mcbsp3_pins: mcbsp3-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_dr */
+		OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)	/* abe_mcbsp3_dx */
+		OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_clkx */
+		OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_fsx */
+		>;
+	};
+};
+
+&omap4_pmx_wkup {
+	usb_gpio_mux_sel2: usb-gpio-mux-sel2-pins {
+		/* gpio_wk0 */
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
+		>;
+	};
+};
+
+/* RNG is used by secure mode and not accessible */
+&rng_target {
+	status = "disabled";
+};
+
+/*
+ * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
+ * for wake-up events for both the USB PHY and the UART. We can use gpio_149
+ * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we
+ * have gpio_149 trigger before the UART transfer starts.
+ */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core 0x110>;
+	uart-has-rtscts;
+	current-speed = <115200>;
+};
+
+&uart3 {
+	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core 0x17c>;
+	overrun-throttle-ms = <500>;
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+
+	bluetooth {
+		compatible = "ti,wl1285-st";
+		enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
+		max-speed = <3686400>;
+	};
+};
+
+/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
+&usb_otg_hs {
+	interface-type = <1>;
+	mode = <3>;
+
+	/*
+	 * Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4.
+	 * VBUS Regulator Main Characteristics". Binding uses 2 mA units.
+	 */
+	power = <150>;
+};
+
+&mcbsp2 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
+
+	mcbsp2_port: port {
+		cpu_dai2: endpoint {
+			dai-format = "i2s";
+			remote-endpoint = <&cpcap_audio_codec0>;
+			frame-master = <&cpcap_audio_codec0>;
+			bitclock-master = <&cpcap_audio_codec0>;
+		};
+	};
+};
+
+&mcbsp3 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp3_pins>;
+	status = "okay";
+
+	mcbsp3_port: port {
+		cpu_dai3: endpoint {
+			dai-format = "dsp_a";
+			frame-master = <&cpcap_audio_codec1>;
+			bitclock-master = <&cpcap_audio_codec1>;
+			remote-endpoint = <&cpcap_audio_codec1>;
+		};
+	};
+};
+
+&cpcap_audio_codec0 {
+	remote-endpoint = <&cpu_dai2>;
+};
+
+&cpcap_audio_codec1 {
+	remote-endpoint = <&cpu_dai3>;
+};
diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-handset.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-handset.dtsi
new file mode 100644
index 000000000000..f3f9ff02b35f
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-handset.dtsi
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-common.dtsi"
+
+/ {
+	/* FS USB Host PHY on port 1 for mdm6600 */
+	fsusb1_phy: usb-phy@1 {
+		compatible = "motorola,mapphone-mdm6600";
+		pinctrl-0 = <&usb_mdm6600_pins>;
+		pinctrl-1 = <&usb_mdm6600_sleep_pins>;
+		pinctrl-names = "default", "sleep";
+		enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
+		power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;	/* gpio_54 */
+		reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;	/* gpio_49 */
+		/* mode: gpio_148 gpio_149 */
+		motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
+				      <&gpio5 21 GPIO_ACTIVE_HIGH>;
+		/* cmd: gpio_103 gpio_104 gpio_142 */
+		motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
+				     <&gpio4 8 GPIO_ACTIVE_HIGH>,
+				     <&gpio5 14 GPIO_ACTIVE_HIGH>;
+		/* status: gpio_52 gpio_53 gpio_55 */
+		motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
+					<&gpio2 21 GPIO_ACTIVE_HIGH>,
+					<&gpio2 23 GPIO_ACTIVE_HIGH>;
+		#phy-cells = <0>;
+	};
+
+	/* HS USB host TLL nop-phy on port 2 for w3glte */
+	hsusb2_phy: usb-phy@2 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
+	pwm8: pwm-8 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_direction_pin>;
+
+		compatible = "ti,omap-dmtimer-pwm";
+		#pwm-cells = <3>;
+		ti,timers = <&timer8>;
+		ti,clock-source = <0x01>;
+	};
+
+	pwm9: pwm-9 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_enable_pin>;
+
+		compatible = "ti,omap-dmtimer-pwm";
+		#pwm-cells = <3>;
+		ti,timers = <&timer9>;
+		ti,clock-source = <0x01>;
+	};
+
+	vibrator {
+		compatible = "pwm-vibrator";
+		pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
+		pwm-names = "enable", "direction";
+		direction-duty-cycle-ns = <10000000>;
+	};
+};
+
+/* Battery NVRAM on 1-wire handled by w1_ds250x driver */
+&hdqw1w {
+	pinctrl-0 = <&hdq_pins>;
+	pinctrl-names = "default";
+	ti,mode = "1w";
+};
+
+&i2c2 {
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_pins>;
+
+		reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */
+
+		/* gpio_183 with sys_nirq2 pad as wakeup */
+		interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>,
+				      <&omap4_pmx_core 0x160>;
+		interrupt-names = "irq", "wakeup";
+		wakeup-source;
+	};
+
+	isl29030@44 {
+		compatible = "isil,isl29030";
+		reg = <0x44>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&als_proximity_pins>;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
+	};
+};
+
+&omap4_pmx_core {
+	hdq_pins: hdq-pins {
+		pinctrl-single,pins = <
+		/* 0x4a100120 hdq_sio.hdq_sio aa27 */
+		OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0)
+		>;
+	};
+
+	/* kpd_row0.gpio_178 */
+	tmp105_irq: tmp105-irq-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	touchscreen_pins: touchscreen-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	usb_mdm6600_pins: usb-mdm6600-pins {
+		pinctrl-single,pins = <
+		/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
+		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
+
+		/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
+		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
+
+		/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
+		OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
+
+		/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
+		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
+
+		/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
+		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
+
+		/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
+		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
+
+		/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
+		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
+
+		/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
+		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
+
+		/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
+		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
+
+		/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
+		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
+
+		/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
+		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
+		>;
+	};
+
+	/* Modem sleep pins to keep gpio_49 high with internal pull */
+	usb_mdm6600_sleep_pins: usb-mdm6600-sleep-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x072, PIN_INPUT_PULLUP | MUX_MODE7) /* Keep gpio_49 reset high */
+		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
+		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
+		>;
+	};
+
+	als_proximity_pins: als-proximity-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	vibrator_direction_pin: vibrator-direction-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)	/* dmtimer8_pwm_evt (gpio_27) */
+		>;
+	};
+
+	vibrator_enable_pin: vibrator-enable-pins {
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)	/* dmtimer9_pwm_evt (gpio_28) */
+		>;
+	};
+};
+
+/* Configure pwm clock source for timers 8 & 9 */
+&timer8 {
+	assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
+	assigned-clock-parents = <&sys_32k_ck>;
+};
+
+&timer9 {
+	assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
+	assigned-clock-parents = <&sys_32k_ck>;
+};
+
+&usbhsohci {
+	phys = <&fsusb1_phy>;
+	phy-names = "usb";
+};
+
+&usbhsehci {
+	phys = <&hsusb2_phy>;
+};
+
+&usbhshost {
+	port1-mode = "ohci-phy-4pin-dpdm";
+	port2-mode = "ehci-tll";
+};
+
+&i2c4 {
+	ak8975: magnetometer@c {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0c>;
+
+		vdd-supply = <&vhvio>;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
+
+		rotation-matrix = "-1", "0", "0",
+				  "0", "1", "0",
+				  "0", "0", "-1";
+
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-mz607-mz617.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-mz607-mz617.dtsi
new file mode 100644
index 000000000000..a356b3a2f24e
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-mz607-mz617.dtsi
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-common.dtsi"
+
+&keypad {
+	keypad,num-rows = <8>;
+	keypad,num-columns = <8>;
+	linux,keymap = <MATRIX_KEY(5, 0, KEY_VOLUMEUP)>,
+		       <MATRIX_KEY(3, 0, KEY_VOLUMEDOWN)>;
+};
+
+/*
+ * On tablets, mmc1 regulator is vsimcard instead of vwlan2 in the stock kernel
+ * dtb. The regulator may not be wired even if a MMC cage is added though.
+ */
+&mmc1 {
+	vmmc-supply = <&vsimcard>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;	/* gpio_176 */
+};
diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi
new file mode 100644
index 000000000000..8b8de92b5424
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-handset.dtsi"
+
+/ {
+	backlight: backlight {
+		compatible = "led-backlight";
+
+		leds = <&backlight_led>;
+		brightness-levels = <31 63 95 127 159 191 223 255>;
+		default-brightness-level = <6>;
+	};
+
+	/* LCD regulator from sw5 source */
+	lcd_regulator: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd";
+		regulator-min-microvolt = <5050000>;
+		regulator-max-microvolt = <5050000>;
+		gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;	/* gpio96 */
+		enable-active-high;
+		vin-supply = <&sw5>;
+	};
+};
+
+&dsi1 {
+	status = "okay";
+	vdd-supply = <&vcsi>;
+
+	port {
+		dsi1_out_ep: endpoint {
+			remote-endpoint = <&lcd0_in>;
+			lanes = <0 1 2 3 4 5>;
+		};
+	};
+
+	lcd0: panel@0 {
+		compatible = "motorola,droid4-panel", "panel-dsi-cm";
+		reg = <0>;
+		label = "lcd0";
+		vddi-supply = <&lcd_regulator>;
+		reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;	/* gpio101 */
+		backlight = <&backlight>;
+
+		width-mm = <50>;
+		height-mm = <89>;
+		rotation = <90>;
+
+		panel-timing {
+			clock-frequency = <0>;		/* Calculated by dsi */
+
+			hback-porch = <2>;
+			hactive = <540>;
+			hfront-porch = <0>;
+			hsync-len = <2>;
+
+			vback-porch = <1>;
+			vactive = <960>;
+			vfront-porch = <0>;
+			vsync-len = <1>;
+
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			lcd0_in: endpoint {
+				remote-endpoint = <&dsi1_out_ep>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/ti/omap/omap-gpmc-smsc911x.dtsi
index ded7e8fec9eb..3046ec572632 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap-gpmc-smsc911x.dtsi
@@ -8,9 +8,9 @@
 
 / {
 	vddvario: regulator-vddvario {
-		  compatible = "regulator-fixed";
-		  regulator-name = "vddvario";
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
 	};
 
 	vdd33a: regulator-vdd33a {
@@ -25,8 +25,8 @@
 		compatible = "smsc,lan9221", "smsc,lan9115";
 		bank-width = <2>;
 		gpmc,device-width = <1>;
-		gpmc,cycle2cycle-samecsen = <1>;
-		gpmc,cycle2cycle-diffcsen = <1>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
 		gpmc,cs-on-ns = <5>;
 		gpmc,cs-rd-off-ns = <150>;
 		gpmc,cs-wr-off-ns = <150>;
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi b/arch/arm/boot/dts/ti/omap/omap-gpmc-smsc9221.dtsi
index 7f6aefd13451..bc8961f3690f 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap-gpmc-smsc9221.dtsi
@@ -12,9 +12,9 @@
 
 / {
 	vddvario: regulator-vddvario {
-		  compatible = "regulator-fixed";
-		  regulator-name = "vddvario";
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
 	};
 
 	vdd33a: regulator-vdd33a {
@@ -29,7 +29,7 @@
 		compatible = "smsc,lan9221","smsc,lan9115";
 		bank-width = <2>;
 
-		gpmc,mux-add-data;
+		gpmc,mux-add-data = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <42>;
 		gpmc,cs-wr-off-ns = <36>;
diff --git a/arch/arm/boot/dts/omap-zoom-common.dtsi b/arch/arm/boot/dts/ti/omap/omap-zoom-common.dtsi
index d4ad9e58b199..8adc0ef01f6c 100644
--- a/arch/arm/boot/dts/omap-zoom-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap-zoom-common.dtsi
@@ -14,7 +14,7 @@
 	 * they probably share the same GPIO IRQ
 	 * REVISIT: Add timing support from slls644g.pdf
 	 */
-	uart@3,0 {
+	serial@3,0 {
 		compatible = "ns16550a";
 		reg = <3 0 8>;	/* CS3, offset 0, IO size 8 */
 		bank-width = <2>;
@@ -27,8 +27,8 @@
 		gpmc,mux-add-data = <0>;
 		gpmc,device-width = <1>;
 		gpmc,wait-pin = <1>;
-		gpmc,cycle2cycle-samecsen = <1>;
-		gpmc,cycle2cycle-diffcsen = <1>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
 		gpmc,cs-on-ns = <5>;
 		gpmc,cs-rd-off-ns = <155>;
 		gpmc,cs-wr-off-ns = <155>;
@@ -50,7 +50,7 @@
 		gpmc,wr-data-mux-bus-ns = <45>;
 		gpmc,wr-access-ns = <145>;
 	};
-	uart@3,1 {
+	serial@3,1 {
 		compatible = "ns16550a";
 		reg = <3 0x100 8>;	/* CS3, offset 0x100, IO size 8 */
 		bank-width = <2>;
@@ -61,7 +61,7 @@
 		clock-frequency = <1843200>;
 		current-speed = <115200>;
 	};
-	uart@3,2 {
+	serial@3,2 {
 		compatible = "ns16550a";
 		reg = <3 0x200 8>;	/* CS3, offset 0x200, IO size 8 */
 		bank-width = <2>;
@@ -72,7 +72,7 @@
 		clock-frequency = <1843200>;
 		current-speed = <115200>;
 	};
-	uart@3,3 {
+	serial@3,3 {
 		compatible = "ns16550a";
 		reg = <3 0x300 8>;	/* CS3, offset 0x300, IO size 8 */
 		bank-width = <2>;
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/ti/omap/omap2.dtsi
index 000bf16de651..afabb36a8ac1 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap2.dtsi
@@ -1,13 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP2 SoC
  *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+#include <dt-bindings/bus/ti-sysc.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/omap.h>
@@ -79,17 +77,37 @@
 			reg = <0x480FE000 0x1000>;
 		};
 
-		sdma: dma-controller@48056000 {
-			compatible = "ti,omap2430-sdma", "ti,omap2420-sdma";
-			ti,hwmods = "dma";
-			reg = <0x48056000 0x1000>;
-			interrupts = <12>,
-				     <13>,
-				     <14>,
-				     <15>;
-			#dma-cells = <1>;
-			dma-channels = <32>;
-			dma-requests = <64>;
+		target-module@48056000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x48056000 0x4>,
+			      <0x4805602c 0x4>,
+			      <0x48056028 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&core_l3_ck>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48056000 0x1000>;
+
+			sdma: dma-controller@0 {
+				compatible = "ti,omap2420-sdma", "ti,omap-sdma";
+				reg = <0 0x1000>;
+				interrupts = <12>,
+					     <13>,
+					     <14>,
+					     <15>;
+				#dma-cells = <1>;
+				dma-channels = <32>;
+				dma-requests = <64>;
+			};
 		};
 
 		i2c1: i2c@48070000 {
@@ -99,8 +117,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <56>;
-			dmas = <&sdma 27 &sdma 28>;
-			dma-names = "tx", "rx";
 		};
 
 		i2c2: i2c@48072000 {
@@ -110,8 +126,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <57>;
-			dmas = <&sdma 29 &sdma 30>;
-			dma-names = "tx", "rx";
 		};
 
 		mcspi1: spi@48098000 {
@@ -180,11 +194,32 @@
 			clock-frequency = <48000000>;
 		};
 
-		timer2: timer@4802a000 {
-			compatible = "ti,omap2420-timer";
-			reg = <0x4802a000 0x400>;
-			interrupts = <38>;
-			ti,hwmods = "timer2";
+		timer2_target: target-module@4802a000 {
+			compatible = "ti,sysc-omap2-timer", "ti,sysc";
+			reg = <0x4802a000 0x4>,
+			      <0x4802a010 0x4>,
+			      <0x4802a014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&gpt2_fck>, <&gpt2_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4802a000 0x1000>;
+
+			timer2: timer@0 {
+				compatible = "ti,omap2420-timer";
+				reg = <0 0x400>;
+				interrupts = <38>;
+			};
 		};
 
 		timer3: timer@48078000 {
diff --git a/arch/arm/boot/dts/omap2420-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap2420-clocks.dtsi
index 00a7a199a91c..00a7a199a91c 100644
--- a/arch/arm/boot/dts/omap2420-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap2420-clocks.dtsi
diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/ti/omap/omap2420-h4.dts
index 7d660271400d..5acf5dd87c59 100644
--- a/arch/arm/boot/dts/omap2420-h4.dts
+++ b/arch/arm/boot/dts/ti/omap/omap2420-h4.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -21,7 +21,7 @@
 
 	nor@0,0 {
 		compatible = "cfi-flash";
-		linux,mtd-name= "intel,ge28f256l18b85";
+		linux,mtd-name = "intel,ge28f256l18b85";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0 0 0x04000000>;
diff --git a/arch/arm/boot/dts/omap2420-n800.dts b/arch/arm/boot/dts/ti/omap/omap2420-n800.dts
index f06d767e818b..f06d767e818b 100644
--- a/arch/arm/boot/dts/omap2420-n800.dts
+++ b/arch/arm/boot/dts/ti/omap/omap2420-n800.dts
diff --git a/arch/arm/boot/dts/omap2420-n810-wimax.dts b/arch/arm/boot/dts/ti/omap/omap2420-n810-wimax.dts
index ac9acbd609b6..ac9acbd609b6 100644
--- a/arch/arm/boot/dts/omap2420-n810-wimax.dts
+++ b/arch/arm/boot/dts/ti/omap/omap2420-n810-wimax.dts
diff --git a/arch/arm/boot/dts/omap2420-n810.dts b/arch/arm/boot/dts/ti/omap/omap2420-n810.dts
index 09c1dbc0bb69..3bf8175d85a8 100644
--- a/arch/arm/boot/dts/omap2420-n810.dts
+++ b/arch/arm/boot/dts/ti/omap/omap2420-n810.dts
@@ -23,7 +23,7 @@
 };
 
 &omap2420_pmx {
-	mcbsp2_pins: mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP2420_CORE_IOPAD(0x0124, PIN_INPUT | MUX_MODE1)	/* eac_ac_sclk.mcbsp2_clkx */
 			OMAP2420_CORE_IOPAD(0x0125, PIN_INPUT | MUX_MODE1)	/* eac_ac_fs.mcbsp2_fsx */
@@ -32,7 +32,7 @@
 		>;
 	};
 
-	aic33_pins: aic33_pins {
+	aic33_pins: aic33-pins {
 		pinctrl-single,pins = <
 			OMAP2420_CORE_IOPAD(0x0129, PIN_OUTPUT | MUX_MODE3)	/* eac_ac_rst.gpio118 */
 			OMAP2420_CORE_IOPAD(0x00e8, PIN_OUTPUT | MUX_MODE2)	/* vlynq_tx1.sys_clkout2 */
diff --git a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi b/arch/arm/boot/dts/ti/omap/omap2420-n8x0-common.dtsi
index 63b0b4921e4e..63b0b4921e4e 100644
--- a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap2420-n8x0-common.dtsi
diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/ti/omap/omap2420.dtsi
index aba542d63d6d..821da51cb870 100644
--- a/arch/arm/boot/dts/omap2420.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap2420.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP2420 SoC
  *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "omap2.dtsi"
@@ -68,10 +65,23 @@
 				};
 			};
 
-			counter32k: counter@4000 {
-				compatible = "ti,omap-counter32k";
-				reg = <0x4000 0x20>;
-				ti,hwmods = "counter_32k";
+			target-module@4000 {
+				compatible = "ti,sysc-omap2", "ti,sysc";
+				reg = <0x4000 0x4>,
+				      <0x4004 0x4>;
+				reg-names = "rev", "sysc";
+				ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+						<SYSC_IDLE_NO>;
+				clocks = <&func_32k_ck>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x4000 0x1000>;
+
+				counter32k: counter@0 {
+					compatible = "ti,omap-counter32k";
+					reg = <0 0x20>;
+				};
 			};
 		};
 
@@ -179,27 +189,47 @@
 			compatible = "ti,omap2-mailbox";
 			reg = <0x48094000 0x200>;
 			interrupts = <26>, <34>;
-			interrupt-names = "dsp", "iva";
 			ti,hwmods = "mailbox";
 			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <6>;
-			mbox_dsp: dsp {
+			mbox_dsp: mbox-dsp {
 				ti,mbox-tx = <0 0 0>;
 				ti,mbox-rx = <1 0 0>;
 			};
-			mbox_iva: iva {
+			mbox_iva: mbox-iva {
 				ti,mbox-tx = <2 1 3>;
 				ti,mbox-rx = <3 1 3>;
 			};
 		};
 
-		timer1: timer@48028000 {
-			compatible = "ti,omap2420-timer";
-			reg = <0x48028000 0x400>;
-			interrupts = <37>;
-			ti,hwmods = "timer1";
-			ti,timer-alwon;
+		timer1_target: target-module@48028000 {
+			compatible = "ti,sysc-omap2-timer", "ti,sysc";
+			reg = <0x48028000 0x4>,
+			      <0x48028010 0x4>,
+			      <0x48028014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&gpt1_fck>, <&gpt1_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x48028000 0x1000>;
+
+			timer1: timer@0 {
+				compatible = "ti,omap2420-timer";
+				reg = <0 0x400>;
+				interrupts = <37>;
+				ti,timer-alwon;
+			};
 		};
 
 		wd_timer2: wdt@48022000 {
@@ -218,5 +248,15 @@
 	compatible = "ti,omap2420-i2c";
 };
 
-/include/ "omap24xx-clocks.dtsi"
-/include/ "omap2420-clocks.dtsi"
+#include "omap24xx-clocks.dtsi"
+#include "omap2420-clocks.dtsi"
+
+/* Preferred always-on timer for clockevent */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt1_fck>;
+		assigned-clock-parents = <&func_32k_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap2430-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap2430-clocks.dtsi
index 4e5ab5189476..4e5ab5189476 100644
--- a/arch/arm/boot/dts/omap2430-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap2430-clocks.dtsi
diff --git a/arch/arm/boot/dts/omap2430-sdp.dts b/arch/arm/boot/dts/ti/omap/omap2430-sdp.dts
index f7e324886642..207070677e3a 100644
--- a/arch/arm/boot/dts/omap2430-sdp.dts
+++ b/arch/arm/boot/dts/ti/omap/omap2430-sdp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -43,8 +43,8 @@
 		gpmc,sync-clk-ps = <0>;
 		gpmc,mux-add-data = <2>;
 		gpmc,device-width = <1>;
-		gpmc,cycle2cycle-samecsen = <1>;
-		gpmc,cycle2cycle-diffcsen = <1>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
 		gpmc,cs-on-ns = <6>;
 		gpmc,cs-rd-off-ns = <187>;
 		gpmc,cs-wr-off-ns = <187>;
diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/ti/omap/omap2430.dtsi
index 7f57af2f10ac..b9a9e6e45266 100644
--- a/arch/arm/boot/dts/omap2430.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap2430.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP243x SoC
  *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "omap2.dtsi"
@@ -81,10 +78,23 @@
 				};
 			};
 
-			counter32k: counter@20000 {
-				compatible = "ti,omap-counter32k";
-				reg = <0x20000 0x20>;
-				ti,hwmods = "counter_32k";
+			target-module@20000 {
+				compatible = "ti,sysc-omap2", "ti,sysc";
+				reg = <0x20000 0x4>,
+				      <0x20004 0x4>;
+				reg-names = "rev", "sysc";
+				ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+						<SYSC_IDLE_NO>;
+				clocks = <&func_32k_ck>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x20000 0x1000>;
+
+				counter32k: counter@0 {
+					compatible = "ti,omap-counter32k";
+					reg = <0 0x20>;
+				};
 			};
 		};
 
@@ -271,18 +281,39 @@
 			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <6>;
-			mbox_dsp: dsp {
+			mbox_dsp: mbox-dsp {
 				ti,mbox-tx = <0 0 0>;
 				ti,mbox-rx = <1 0 0>;
 			};
 		};
 
-		timer1: timer@49018000 {
-			compatible = "ti,omap2420-timer";
-			reg = <0x49018000 0x400>;
-			interrupts = <37>;
-			ti,hwmods = "timer1";
-			ti,timer-alwon;
+		timer1_target: target-module@49018000 {
+			compatible = "ti,sysc-omap2-timer", "ti,sysc";
+			reg = <0x49018000 0x4>,
+			      <0x49018010 0x4>,
+			      <0x49018014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&gpt1_fck>, <&gpt1_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49018000 0x1000>;
+
+			timer1: timer@0 {
+				compatible = "ti,omap2420-timer";
+				reg = <0 0x400>;
+				interrupts = <37>;
+				ti,timer-alwon;
+			};
 		};
 
 		mcspi3: spi@480b8000 {
@@ -309,6 +340,10 @@
 	};
 };
 
+&sdma {
+	compatible = "ti,omap2430-sdma", "ti,omap-sdma";
+};
+
 &i2c1 {
 	compatible = "ti,omap2430-i2c";
 };
@@ -317,5 +352,15 @@
 	compatible = "ti,omap2430-i2c";
 };
 
-/include/ "omap24xx-clocks.dtsi"
-/include/ "omap2430-clocks.dtsi"
+#include "omap24xx-clocks.dtsi"
+#include "omap2430-clocks.dtsi"
+
+/* Preferred always-on timer for clockevent */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt1_fck>;
+		assigned-clock-parents = <&func_32k_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap24xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap24xx-clocks.dtsi
index 07af87edf0e2..07af87edf0e2 100644
--- a/arch/arm/boot/dts/omap24xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap24xx-clocks.dtsi
diff --git a/arch/arm/boot/dts/ti/omap/omap3-beagle-ab4.dts b/arch/arm/boot/dts/ti/omap/omap3-beagle-ab4.dts
new file mode 100644
index 000000000000..990ff2d84686
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap3-beagle-ab4.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "omap3-beagle.dts"
+
+/ {
+	model = "TI OMAP3 BeagleBoard A to B4";
+	compatible = "ti,omap3-beagle-ab4", "ti,omap3-beagle", "ti,omap3430", "ti,omap3";
+};
+
+/*
+ * Workaround for capacitor C70 issue, see "Boards revision A and < B5"
+ * section at https://elinux.org/BeagleBoard_Community
+ */
+
+/* Unusable as clocksource because of unreliable oscillator */
+&counter32k {
+	status = "disabled";
+};
+
+/* Unusable as clockevent because of unreliable oscillator, allow to idle */
+&timer1_target {
+	/delete-property/ti,no-reset-on-init;
+	/delete-property/ti,no-idle;
+	timer@0 {
+		/delete-property/ti,timer-alwon;
+	};
+};
+
+/* Preferred always-on timer for clocksource */
+&timer12_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		/* Always clocked by secure_32k_fck */
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt2_fck>;
+		assigned-clock-parents = <&sys_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap3-beagle-xm-ab.dts b/arch/arm/boot/dts/ti/omap/omap3-beagle-xm-ab.dts
index e498495b8465..cb6968a8bce8 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm-ab.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-beagle-xm-ab.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "omap3-beagle-xm.dts"
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/ti/omap/omap3-beagle-xm.dts
index 125ed933ca75..08ee0f8ea68f 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-beagle-xm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -8,7 +8,7 @@
 
 / {
 	model = "TI OMAP3 BeagleBoard xM";
-	compatible = "ti,omap3-beagle-xm", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "ti,omap3-beagle-xm", "ti,omap3630", "ti,omap3";
 
 	cpus {
 		cpu@0 {
@@ -34,26 +34,26 @@
 		clock-frequency = <26000000>;
 	};
 
-	leds {
+	led-controller-1 {
 		compatible = "gpio-leds";
 
-		heartbeat {
+		led-1 {
 			label = "beagleboard::usr0";
 			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */
 			linux,default-trigger = "heartbeat";
 		};
 
-		mmc {
+		led-2 {
 			label = "beagleboard::usr1";
 			gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */
 			linux,default-trigger = "mmc0";
 		};
 	};
 
-	pwmleds {
+	led-controller-2 {
 		compatible = "pwm-leds";
 
-		pmu_stat {
+		led-3 {
 			label = "beagleboard::pmu_stat";
 			pwms = <&twl_pwmled 1 7812500>;
 			max-brightness = <127>;
@@ -90,7 +90,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
@@ -183,13 +183,13 @@
 };
 
 &omap3_pmx_wkup {
-	gpio1_pins: pinmux_gpio1_pins {
+	gpio1_pins: gpio1-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */
 		>;
 	};
 
-	dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+	dss_dpi_pins2: dss-dpi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3)   /* sys_boot0.dss_data18 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3)   /* sys_boot1.dss_data19 */
@@ -207,14 +207,14 @@
 			&hsusb2_pins
 	>;
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
 		>;
 	};
 
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
@@ -225,7 +225,7 @@
 		>;
 	};
 
-	dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+	dss_dpi_pins1: dss-dpi2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -261,7 +261,7 @@
 			&hsusb2_2_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -370,7 +370,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
@@ -389,7 +389,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <
@@ -406,7 +406,7 @@
 };
 
 &venc {
-	status = "ok";
+	status = "okay";
 
 	vdda-supply = <&vdac>;
 
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/ti/omap/omap3-beagle.dts
index 4ed3f93f5841..4d9a8eab6abf 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-beagle.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -28,18 +28,18 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pmu_stat {
+		led-pmu-stat {
 			label = "beagleboard::pmu_stat";
 			gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
 		};
 
-		heartbeat {
+		led-heartbeat {
 			label = "beagleboard::usr0";
 			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */
 			linux,default-trigger = "heartbeat";
 		};
 
-		mmc {
+		led-mmc {
 			label = "beagleboard::usr1";
 			gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */
 			linux,default-trigger = "mmc0";
@@ -57,7 +57,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;	/* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
@@ -170,7 +170,7 @@
 };
 
 &omap3_pmx_wkup {
-	gpio1_pins: pinmux_gpio1_pins {
+	gpio1_pins: gpio1-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot5.gpio_7 */
 		>;
@@ -183,7 +183,7 @@
 			&hsusb2_pins
 	>;
 
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
@@ -194,20 +194,20 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
-	tfp410_pins: pinmux_tfp410_pins {
+	tfp410_pins: tfp410-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -247,7 +247,7 @@
 			&hsusb2_2_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -353,7 +353,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
@@ -367,7 +367,7 @@
 };
 
 &venc {
-	status = "ok";
+	status = "okay";
 
 	vdda-supply = <&vdac>;
 
@@ -380,7 +380,7 @@
 };
 
 &gpmc {
-	status = "ok";
+	status = "okay";
 	ranges = <0 0 0x30000000 0x1000000>;	/* CS0 space, 16MB */
 
 	/* Chip select 0 */
diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/ti/omap/omap3-cm-t3517.dts
index 632f52efdf98..f776e0527049 100644
--- a/arch/arm/boot/dts/omap3-cm-t3517.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-cm-t3517.dts
@@ -11,12 +11,12 @@
 	model = "CompuLab CM-T3517";
 	compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
 
-	vmmc:  regulator-vmmc {
-                compatible = "regulator-fixed";
-                regulator-name = "vmmc";
-                regulator-min-microvolt = <3300000>;
-                regulator-max-microvolt = <3300000>;
-        };
+	vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
 	wl12xx_vmmc2: wl12xx_vmmc2 {
 		compatible = "regulator-fixed";
@@ -43,7 +43,7 @@
 
 &omap3_pmx_wkup {
 
-	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+	wl12xx_wkup_pins: wl12xx-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
 			OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4)	/* sys_boot4.gpio_6 */
@@ -53,25 +53,25 @@
 
 &omap3_pmx_core {
 
-	phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
+	phy1_reset_pins: hsusb1-phy-reset-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4)	/* uart2_tx.gpio_146 */
 		>;
 	};
 
-	phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
+	phy2_reset_pins: hsusb2-phy-reset-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4)	/* uart2_rx.gpio_147 */
 		>;
 	};
 
-	otg_drv_vbus: pinmux_otg_drv_vbus {
+	otg_drv_vbus: otg-drv-vbus-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50MHz_clk.usb0_drvvbus */
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
@@ -82,14 +82,14 @@
 		>;
 	};
 
-	wl12xx_core_pins: pinmux_wl12xx_core_pins {
+	wl12xx_core_pins: wl12xx-core-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs5.gpio_56 */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart2_rts.gpio_145 */
 		>;
 	};
 
-	usb_hub_pins: pinmux_usb_hub_pins {
+	usb_hub_pins: usb-hub-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 - USB HUB RST */
 		>;
@@ -147,7 +147,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <
diff --git a/arch/arm/boot/dts/omap3-cm-t3530.dts b/arch/arm/boot/dts/ti/omap/omap3-cm-t3530.dts
index 32dbaeaed147..0c6f14963e5e 100644
--- a/arch/arm/boot/dts/omap3-cm-t3530.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-cm-t3530.dts
@@ -23,7 +23,7 @@
 };
 
 &omap3_pmx_core {
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
@@ -49,7 +49,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <
diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/ti/omap/omap3-cm-t3730.dts
index 683819bf0915..f1a8f0fd7a83 100644
--- a/arch/arm/boot/dts/omap3-cm-t3730.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-cm-t3730.dts
@@ -9,7 +9,7 @@
 
 / {
 	model = "CompuLab CM-T3730";
-	compatible = "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap3";
 
 	wl12xx_vmmc2: wl12xx_vmmc2 {
 		compatible = "regulator-fixed";
@@ -33,7 +33,7 @@
 };
 
 &omap3_pmx_wkup {
-	dss_dpi_pins_cm_t3730: pinmux_dss_dpi_pins_cm_t3730 {
+	dss_dpi_pins_cm_t3730: dss-dpi-cm-t3730-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a08, PIN_OUTPUT | MUX_MODE3)   /* sys_boot0.dss_data18 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3)   /* sys_boot1.dss_data19 */
@@ -47,7 +47,7 @@
 
 &omap3_pmx_core {
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
@@ -58,7 +58,7 @@
 		>;
 	};
 
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)	/* dss_data3.gpio_73 */
 			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 */
@@ -87,7 +87,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <
diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/ti/omap/omap3-cm-t3x.dtsi
index cdb632df152a..950a29f9b4a0 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-cm-t3x.dtsi
@@ -47,7 +47,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&hsusb2_power>;
 		#phy-cells = <0>;
@@ -74,14 +74,14 @@
 
 &omap3_pmx_core {
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT  | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -92,13 +92,13 @@
 		>;
 	};
 
-	green_led_pins: pinmux_green_led_pins {
+	green_led_pins: green-led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4)	/* sys_clkout2.gpio_186 */
 		>;
 	};
 
-	dss_dpi_pins_common: pinmux_dss_dpi_pins_common {
+	dss_dpi_pins_common: dss-dpi-common-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -126,7 +126,7 @@
 		>;
 	};
 
-	dss_dpi_pins_cm_t35x: pinmux_dss_dpi_pins_cm_t35x {
+	dss_dpi_pins_cm_t35x: dss-dpi-cm-t35x-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)	/* dss_data0.dss_data0 */
 			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)	/* dss_data1.dss_data1 */
@@ -137,13 +137,13 @@
 		>;
 	};
 
-	ads7846_pins: pinmux_ads7846_pins {
+	ads7846_pins: ads7846-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20ba, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_ncs6.gpio_57 */
 		>;
 	};
 
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo */
@@ -152,14 +152,14 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx */
 			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)	/* mcbsp2_clkx */
@@ -227,7 +227,7 @@
 
 		interrupt-parent = <&gpio2>;
 		interrupts = <25 0>;		/* gpio_57 */
-		pendown-gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
@@ -246,7 +246,7 @@
 };
 
 &venc {
-	status = "ok";
+	status = "okay";
 
 	port {
 		venc_out: endpoint {
@@ -257,7 +257,7 @@
 };
 
 &mcbsp2 {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/ti/omap/omap3-cm-t3x30.dtsi
index 5e8943539fcc..0e942513560d 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-cm-t3x30.dtsi
@@ -22,14 +22,14 @@
 
 &omap3_pmx_core {
 
-	smsc1_pins: pinmux_smsc1_pins {
+	smsc1_pins: smsc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs5.gpmc_ncs5 */
 			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
 		>;
 	};
 
- 	hsusb0_pins: pinmux_hsusb0_pins {
+ 	hsusb0_pins: hsusb0-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
 			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
diff --git a/arch/arm/boot/dts/ti/omap/omap3-cpu-thermal.dtsi b/arch/arm/boot/dts/ti/omap/omap3-cpu-thermal.dtsi
new file mode 100644
index 000000000000..7dd2340bc5e4
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap3-cpu-thermal.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree Source for OMAP3 SoC CPU thermal
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+cpu_thermal: cpu-thermal {
+	polling-delay-passive = <250>; /* milliseconds */
+	polling-delay = <1000>; /* milliseconds */
+	coefficients = <0 20000>;
+
+	thermal-sensors = <&bandgap>;
+
+	cpu_trips: trips {
+		cpu_alert0: cpu_alert {
+			temperature = <80000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu_crit: cpu_crit {
+			temperature = <90000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "critical";
+		};
+	};
+
+	cpu_cooling_maps: cooling-maps {
+		map0 {
+			trip = <&cpu_alert0>;
+			cooling-device =
+				<&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-common.dtsi
index ac3d996cec5c..07d5894ebb74 100644
--- a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-common.dtsi
@@ -15,28 +15,28 @@
 	leds {
 		compatible = "gpio-leds";
 
-		heartbeat {
+		led-heartbeat {
 			label = "devkit8000::led1";
 			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;	/* 186 -> LED1 */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		mmc {
+		led-mmc {
 			label = "devkit8000::led2";
 			gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;	/* 163 -> LED2 */
 			default-state = "on";
 			linux,default-trigger = "none";
 		};
 
-		usr {
+		led-usr {
 			label = "devkit8000::led3";
 			gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>;	/* 164 -> LED3 */
 			default-state = "on";
 			linux,default-trigger = "usr";
 		};
 
-		pmu_stat {
+		led-pmu-stat {
 			label = "devkit8000::pmu_stat";
 			gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
 		};
@@ -158,6 +158,24 @@
 	status = "disabled";
 };
 
+/* Unusable as clockevent because if unreliable oscillator, allow to idle */
+&timer1_target {
+	/delete-property/ti,no-reset-on-init;
+	/delete-property/ti,no-idle;
+	timer@0 {
+		/delete-property/ti,timer-alwon;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer12_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		/* Always clocked by secure_32k_fck */
+	};
+};
+
 &twl_gpio {
 	ti,use-leds;
 	/*
@@ -257,8 +275,8 @@
 
 	ethernet@6,0 {
 		compatible = "davicom,dm9000";
-		reg =  <6 0x000 2
-			6 0x400 2>; /* CS6, offset 0 and 0x400, IO size 2 */
+		reg =  <6 0x000 2>,
+		       <6 0x400 2>; /* CS6, offset 0 and 0x400, IO size 2 */
 		bank-width = <2>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
@@ -267,8 +285,8 @@
 		gpmc,mux-add-data = <0>;
 		gpmc,device-width = <1>;
 		gpmc,wait-pin = <0>;
-		gpmc,cycle2cycle-samecsen = <1>;
-		gpmc,cycle2cycle-diffcsen = <1>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
 
 		gpmc,cs-on-ns = <6>;
 		gpmc,cs-rd-off-ns = <180>;
@@ -294,7 +312,7 @@
 };
 
 &omap3_pmx_core {
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -337,7 +355,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
@@ -361,7 +379,7 @@
 };
 
 &venc {
-	status = "ok";
+	status = "okay";
 
 	vdda-supply = <&vdac>;
 
diff --git a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-lcd-common.dtsi
index 3decc2d78a6c..a7f99ae0c1fe 100644
--- a/arch/arm/boot/dts/omap3-devkit8000-lcd-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-lcd-common.dtsi
@@ -54,7 +54,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <27 0>;		/* gpio_27 */
-		pendown-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
diff --git a/arch/arm/boot/dts/omap3-devkit8000-lcd43.dts b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-lcd43.dts
index afed85078ad8..afed85078ad8 100644
--- a/arch/arm/boot/dts/omap3-devkit8000-lcd43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-lcd43.dts
diff --git a/arch/arm/boot/dts/omap3-devkit8000-lcd70.dts b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-lcd70.dts
index 07c51a105c0d..07c51a105c0d 100644
--- a/arch/arm/boot/dts/omap3-devkit8000-lcd70.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-devkit8000-lcd70.dts
diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/ti/omap/omap3-devkit8000.dts
index 162d0726b008..162d0726b008 100644
--- a/arch/arm/boot/dts/omap3-devkit8000.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-devkit8000.dts
diff --git a/arch/arm/boot/dts/ti/omap/omap3-echo.dts b/arch/arm/boot/dts/ti/omap/omap3-echo.dts
new file mode 100644
index 000000000000..96011c976f5b
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap3-echo.dts
@@ -0,0 +1,724 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2019 André Hentschel <nerv@dawncrow.de>
+ */
+/dts-v1/;
+
+#include "dm3725.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Amazon Echo (first generation)";
+	compatible = "amazon,omap3-echo", "ti,omap3630", "ti,omap3";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0xc600000>; /* 198 MB */
+	};
+
+	vcc5v: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc3v3: fixedregulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc1v8: fixedregulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <40>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&button_pins>;
+
+		mute-button {
+			label = "mute";
+			linux,code = <KEY_MUTE>;
+			gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;	/* GPIO_70 */
+			wakeup-source;
+		};
+
+		help-button {
+			label = "help";
+			linux,code = <KEY_HELP>;
+			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;	/* GPIO_72 */
+			wakeup-source;
+		};
+	};
+
+	rotary: rotary-encoder {
+		compatible = "rotary-encoder";
+		gpios = <
+			&gpio3  5 GPIO_ACTIVE_HIGH /* GPIO_69 */
+			&gpio3 12 GPIO_ACTIVE_HIGH /* GPIO_76 */
+		>;
+		linux,axis = <REL_X>;
+		rotary-encoder,relative-axis;
+	};
+
+	speaker_amp: speaker-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;	/* gpio_129 */
+		sound-name-prefix = "Speaker Amp";
+		VCC-supply = <&vcc1v8>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "Misto Speaker";
+		simple-audio-card,widgets =
+			"Speaker", "Speaker";
+		simple-audio-card,routing =
+			"Speaker Amp INL", "HPL",
+			"Speaker Amp INR", "HPR",
+			"Speaker", "Speaker Amp OUTL",
+			"Speaker", "Speaker Amp OUTR";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,aux-devs = <&speaker_amp>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcbsp2>;
+		};
+
+		sound_master: simple-audio-card,codec {
+			sound-dai = <&codec0>;
+			system-clock-frequency = <19200000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&mcbsp2 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	lp5523A: lp5523A@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "national,lp5523";
+		label = "q1";
+		reg = <0x32>;
+		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+		enable-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* GPIO_109 */
+
+		multi-led@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@0 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x0>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@1 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@6 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x6>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@2 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x3>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@7 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x7>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@4 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x4>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@5 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x5>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@8 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x8>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+	};
+
+	lp5523B: lp5523B@33 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "national,lp5523";
+		label = "q3";
+		reg = <0x33>;
+		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+
+		multi-led@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@0 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x0>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@1 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@6 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x6>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@2 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x3>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@7 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x7>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@4 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x4>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@5 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x5>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@8 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x8>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+	};
+
+	lp5523C: lp5523C@34 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "national,lp5523";
+		label = "q4";
+		reg = <0x34>;
+		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+
+		multi-led@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@0 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x0>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@1 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@6 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x6>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@2 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x3>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@7 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x7>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@4 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x4>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@5 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x5>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@8 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x8>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+	};
+
+	lp5523D: lp552D@35 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "national,lp5523";
+		label = "q2";
+		reg = <0x35>;
+		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
+
+		multi-led@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@0 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x0>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@1 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@6 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x6>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@2 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x3>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@7 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x7>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+		multi-led@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+			color = <LED_COLOR_ID_RGB>;
+
+			led@4 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x4>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@5 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x5>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@8 {
+				led-cur = /bits/ 8 <12>;
+				max-cur = /bits/ 8 <15>;
+				reg = <0x8>;
+				color = <LED_COLOR_ID_RED>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	codec0: codec@18 {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&sys_clkout1>;
+		clock-names = "mclk";
+		ldoin-supply = <&vcc1v8>;
+		iov-supply = <&vcc1v8>;
+		reset-gpios = <&gpio3 10 GPIO_ACTIVE_LOW>;	/* gpio_74 */
+	};
+};
+
+
+#include "../../tps65910.dtsi"
+
+&omap3_pmx_core {
+	tps_pins: tps-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21e0, PIN_INPUT_PULLUP | PIN_OFF_INPUT_PULLUP | PIN_OFF_OUTPUT_LOW | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* sys_nirq.sys_nirq */
+		>;
+	};
+
+	button_pins: button-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_INPUT | MUX_MODE4)	/* dss_data0.gpio_70 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4)	/* dss_data2.gpio_72 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4)	/* dss_data4.gpio_74 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4)	/* dss_data15.gpio_85 */
+			OMAP3_CORE1_IOPAD(0x2a1a, PIN_OUTPUT | MUX_MODE0)	/* sys_clkout1.sys_clkout1 */
+		>;
+	};
+
+	mmc1_pins: mmc1-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	mmc2_pins: mmc2-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat4.sdmmc2_dat4 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat5.sdmmc2_dat5 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat6.sdmmc2_dat6 */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat7.sdmmc2_dat7 */
+		>;
+	};
+
+	mcbsp2_pins: mcbsp2-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx.mcbsp2_fsx */
+			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)	/* mcbsp2_clkx.mcbsp2_clkx */
+			OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)	/* mcbsp2_dr.mcbsp2.dr */
+			OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)	/* mcbsp2_dx.mcbsp2_dx */
+		>;
+	};
+};
+
+&omap3_pmx_core2 {
+	mmc3_pins: mmc3-pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
+			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_ctl.sdmmc3_cmd */
+			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d5.sdmmc3_dat1 */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
+		>;
+	};
+};
+
+&mmc1 {
+	status = "okay";
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&vmmc_reg>;
+};
+
+&mmc2 {
+	status = "okay";
+	bus-width = <8>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&vmmc_reg>;
+};
+
+&mmc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins>;
+	non-removable;
+	disable-wp;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	vmmc-supply = <&vcc3v3>;
+	vqmmc-supply = <&vcc1v8>;
+	atheros@0 {
+		compatible = "atheros,ath6kl";
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&tps {
+	pinctrl-names = "default";
+	pinctrl-0 = <&tps_pins>;
+
+	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+	interrupt-parent = <&intc>;
+
+	ti,en-ck32k-xtal;
+	ti,system-power-controller;
+
+	vcc1-supply = <&vcc5v>;
+	vcc2-supply = <&vcc5v>;
+	vcc3-supply = <&vcc5v>;
+	vcc4-supply = <&vcc5v>;
+	vcc5-supply = <&vcc5v>;
+	vcc6-supply = <&vcc5v>;
+	vcc7-supply = <&vcc5v>;
+	vccio-supply = <&vcc5v>;
+
+	regulators {
+
+		vio_reg: regulator@1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			regulator-name = "vdd_dsp";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <2700000>;
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <2500000>;
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2850000>;
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/ti/omap/omap3-evm-37xx.dts
index e0c0382388f0..e0346bf842fc 100644
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-evm-37xx.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -17,7 +17,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&hsusb2_2_pins>;
 
-	ehci_phy_pins: pinmux_ehci_phy_pins {
+	ehci_phy_pins: ehci-phy-pins {
 		pinctrl-single,pins = <
 
 		/* EHCI PHY reset GPIO etk_d7.gpio_21 */
@@ -29,7 +29,7 @@
 	};
 
 	/* Used by OHCI and EHCI. OHCI won't work without external phy */
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 
 		/* etk_d10.hsusb2_clk */
@@ -60,7 +60,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "hynix,h8kds0un0mer-4em";
+		linux,mtd-name = "hynix,h8kds0un0mer-4em";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-evm-common.dtsi
index 17c89df6ce6b..1b6023c4cdf3 100644
--- a/arch/arm/boot/dts/omap3-evm-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-evm-common.dtsi
@@ -25,7 +25,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */
 		vcc-supply = <&hsusb2_power>;
diff --git a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-evm-processor-common.dtsi
index b4109f48ec18..e27837093e43 100644
--- a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-evm-processor-common.dtsi
@@ -33,7 +33,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
 
-	dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+	dss_dpi_pins1: dss-dpi2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -62,7 +62,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
@@ -78,7 +78,7 @@
 	};
 
 	/* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
@@ -93,7 +93,7 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
@@ -101,14 +101,14 @@
 	};
 
 	/* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
-	on_board_gpio_61: pinmux_ehci_port_select_pins {
+	on_board_gpio_61: ehci-port-select-pins {
 		pinctrl-single,pins = <
 		OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
 		>;
 	};
 
 	/* Used by OHCI and EHCI. OHCI won't work without external phy */
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 
 		/* mcspi1_cs3.hsusb2_data2 */
@@ -135,14 +135,14 @@
 	 * Note that gpio_150 pulled high with internal pull to prevent wlcore
 	 * reset on return from off mode in idle.
 	 */
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE7)		/* uart1_cts.gpio_150 */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4)		/* uart1_rts.gpio_149 */
 		>;
 	};
 
-	smsc911x_pins: pinmux_smsc911x_pins {
+	smsc911x_pins: smsc911x-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
 		>;
@@ -150,7 +150,7 @@
 };
 
 &omap3_pmx_wkup {
-	dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+	dss_dpi_pins2: dss-dpi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3)   /* sys_boot0.dss_data18 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3)   /* sys_boot1.dss_data19 */
@@ -195,7 +195,7 @@
  * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
  */
 &gpio2 {
-	en_usb2_port {
+	en-usb2-port-hog {
 		gpio-hog;
 		gpios = <29 GPIO_ACTIVE_HIGH>;	/* gpio_61 */
 		output-low;
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/ti/omap/omap3-evm.dts
index 6a94815feb76..a2a1613c45c3 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-evm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -17,7 +17,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&hsusb2_2_pins>;
 
-	ehci_phy_pins: pinmux_ehci_phy_pins {
+	ehci_phy_pins: ehci-phy-pins {
 		pinctrl-single,pins = <
 
 		/* EHCI PHY reset GPIO etk_d7.gpio_21 */
@@ -29,7 +29,7 @@
 	};
 
 	/* Used by OHCI and EHCI. OHCI won't work without external phy */
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 
 		/* etk_d10.hsusb2_clk */
@@ -60,7 +60,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,mt29f2g16abdhc";
+		linux,mtd-name = "micron,mt29f2g16abdhc";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/ti/omap/omap3-gta04.dtsi
index 409a758c99f1..3661340009e7 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-gta04.dtsi
@@ -11,8 +11,7 @@
 
 / {
 	model = "OMAP3 GTA04";
-	compatible = "ti,omap3-gta04", "ti,omap3630", "ti,omap36xx", "ti,omap3";
-
+	compatible = "goldelico,gta04", "ti,omap3630", "ti,omap3";
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&vcc>;
@@ -31,6 +30,8 @@
 	aliases {
 		display0 = &lcd;
 		display1 = &tv0;
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
 	};
 
 	ldo_3v3: fixedregulator {
@@ -104,17 +105,17 @@
 		#sound-dai-cells = <0>;
 	};
 
-	spi_lcd: spi_lcd {
+	spi_lcd: spi {
 		compatible = "spi-gpio";
 		#address-cells = <0x1>;
 		#size-cells = <0x0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi_gpio_pins>;
 
-		gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 20 GPIO_ACTIVE_HIGH>;
-		cs-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 
 		/* lcd panel */
@@ -124,9 +125,8 @@
 			spi-max-frequency = <100000>;
 			spi-cpol;
 			spi-cpha;
-			spi-cs-high;
 
-			backlight= <&backlight>;
+			backlight = <&backlight>;
 			label = "lcd";
 			port {
 				lcd_in: endpoint {
@@ -146,13 +146,14 @@
 		pinctrl-0 = <&backlight_pins>;
 	};
 
-	pwm11: dmtimer-pwm {
+	pwm11: pwm-11 {
 		compatible = "ti,omap-dmtimer-pwm";
 		ti,timers = <&timer11>;
 		#pwm-cells = <3>;
+		ti,clock-source = <0x01>;
 	};
 
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 		#phy-cells = <0>;
@@ -199,7 +200,7 @@
 	};
 
 	/* devconf0 setup for mcbsp1 clock pins */
-	pinmux_mcbsp1@48002274 {
+	pinmux@48002274 {
 		compatible = "pinctrl-single";
 		reg = <0x48002274 4>;   /* CONTROL_DEVCONF0 */
 		#address-cells = <1>;
@@ -210,14 +211,14 @@
 		#pinctrl-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcbsp1_devconf0_pins>;
-		mcbsp1_devconf0_pins: pinmux_mcbsp1_devconf0_pins {
+		mcbsp1_devconf0_pins: mcbsp1-devconf0-pins {
 			/*                   offset bits mask */
 			pinctrl-single,bits = <0x00 0x08 0x1c>;	/* set MCBSP1_CLKR */
 		};
 	};
 
 	/* devconf1 setup for tvout pins */
-	pinmux_tv_out@480022d8 {
+	pinmux@480022d8 {
 		compatible = "pinctrl-single";
 		reg = <0x480022d8 4>;	/* CONTROL_DEVCONF1 */
 		#address-cells = <1>;
@@ -228,7 +229,7 @@
 		#pinctrl-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tv_acbias_devconf1_pins>;
-		tv_acbias_devconf1_pins: pinmux_tv_acbias_devconf1_pins {
+		tv_acbias_devconf1_pins: tv-acbias-devconf1-pins {
 			/*			offset	bits	mask */
 			pinctrl-single,bits = <0x00 0x40800 0x40800>;	/* set TVOUTBYPASS and TVOUTACEN */
 		};
@@ -236,7 +237,7 @@
 };
 
 &omap3_pmx_wkup {
-	gpio1_pins: pinmux_gpio1_pins {
+	gpio1_pins: gpio1-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot5.gpio_7 */
 			OMAP3_WKUP_IOPAD(0x2a1a, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_clkout.gpio_10 */
@@ -250,7 +251,7 @@
 			&hsusb2_pins
 	>;
 
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
@@ -261,28 +262,28 @@
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0)		/* uart1_rx.uart1_rx */
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)		/* uart1_tx.uart1_tx */
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
 			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx.uart3_rx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx.uart3_tx */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
@@ -293,13 +294,13 @@
 		>;
 	};
 
-	backlight_pins: backlight_pins_pinmux {
+	backlight_pins: backlight-pinmux-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20ba, MUX_MODE3)		/* gpt11/gpio57 */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -330,52 +331,52 @@
 			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
 			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
 		>;
-       };
+	};
 
-	gps_pins: pinmux_gps_pins {
+	gps_pins: gps-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* gpio145 */
 		>;
 	};
 
-	hdq_pins: hdq_pins {
+	hdq_pins: hdq-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda.hdq */
 		>;
 	};
 
-	bmp085_pins: pinmux_bmp085_pins {
+	bmp085_pins: bmp085-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2136, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio113 */
 		>;
 	};
 
-	bma180_pins: pinmux_bma180_pins {
+	bma180_pins: bma180-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213a, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio115 */
 		>;
 	};
 
-	itg3200_pins: pinmux_itg3200_pins {
+	itg3200_pins: itg3200-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b8, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio56 */
 		>;
 	};
 
-	hmc5843_pins: pinmux_hmc5843_pins {
+	hmc5843_pins: hmc5843-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2134, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio112 */
 		>;
 	};
 
-	penirq_pins: pinmux_penirq_pins {
+	penirq_pins: penirq-pins {
 		pinctrl-single,pins = <
 			/* here we could enable to wakeup the cpu from suspend by a pen touch */
 			OMAP3_CORE1_IOPAD(0x2194, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio160 */
 		>;
 	};
 
-	camera_pins: pinmux_camera_pins {
+	camera_pins: camera-pins {
 		pinctrl-single,pins = <
 			/* set up parallel camera interface */
 			OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* cam_hs */
@@ -401,7 +402,7 @@
 		>;
 	};
 
-	mcbsp1_pins: pinmux_mcbsp1_pins {
+	mcbsp1_pins: mcbsp1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT | MUX_MODE4)	/* mcbsp1_clkr.mcbsp1_clkr - gpio_156 FM interrupt */
 			OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE0)	/* mcbsp1_clkr.mcbsp1_fsr */
@@ -414,7 +415,7 @@
 		>;
 	};
 
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx.mcbsp2_fsx */
 			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx.mcbsp2_clkx */
@@ -423,7 +424,7 @@
 		>;
 	};
 
-	mcbsp3_pins: pinmux_mcbsp3_pins {
+	mcbsp3_pins: mcbsp3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216c, PIN_OUTPUT | MUX_MODE0)	/* mcbsp3_dx.mcbsp3_dx */
 			OMAP3_CORE1_IOPAD(0x216e, PIN_INPUT | MUX_MODE0)	/* mcbsp3_dx.mcbsp3_dr */
@@ -432,7 +433,7 @@
 		>;
 	};
 
-	mcbsp4_pins: pinmux_mcbsp4_pins {
+	mcbsp4_pins: mcbsp4-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcbsp4_clkx.mcbsp4_clkx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcbsp4_clkx.mcbsp4_dr */
@@ -447,7 +448,7 @@
 			&hsusb2_2_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -458,7 +459,7 @@
 		>;
 	};
 
-	spi_gpio_pins: spi_gpio_pinmux {
+	spi_gpio_pins: spi-gpio-pinmux-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE4) /* clk */
 			OMAP3630_CORE2_IOPAD(0x25e6, PIN_OUTPUT | MUX_MODE4) /* cs */
@@ -488,8 +489,8 @@
 		};
 
 		twl_power: power {
-			compatible = "ti,twl4030-power";
-			ti,use_poweroff;
+			compatible = "ti,twl4030-power-idle";
+			ti,system-power-controller;
 		};
 	};
 };
@@ -508,6 +509,8 @@
 		pinctrl-0 = <&bmp085_pins>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* GPIO_113 */
+		vdda-supply = <&vio>;
+		vddd-supply = <&vio>;
 	};
 
 	/* accelerometer */
@@ -515,7 +518,7 @@
 		compatible = "bosch,bma180";
 		reg = <0x41>;
 		pinctrl-names = "default";
-		pintcrl-0 = <&bma180_pins>;
+		pinctrl-0 = <&bma180_pins>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_115 */
 	};
@@ -540,28 +543,29 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 
-		gta04_led0: red_aux@0 {
+		gta04_led0: led@0 {
 			label = "gta04:red:aux";
 			reg = <0x0>;
 		};
 
-		gta04_led1: green_aux@1 {
+		gta04_led1: led@1 {
 			label = "gta04:green:aux";
 			reg = <0x1>;
 		};
 
-		gta04_led3: red_power@3 {
+		gta04_led3: led@3 {
 			label = "gta04:red:power";
 			reg = <0x3>;
 			linux,default-trigger = "default-on";
 		};
 
-		gta04_led4: green_power@4 {
+		gta04_led4: led@4 {
 			label = "gta04:green:power";
 			reg = <0x4>;
 		};
 
-		wifi_reset: wifi_reset@6 { /* reference as <&tca_gpios 0 0> since it is currently the only GPIO */
+		wifi_reset: led@6 {
+			/* reference as <&tca_gpios 0 0> since it is currently the only GPIO */
 			reg = <0x6>;
 			compatible = "gpio";
 		};
@@ -607,6 +611,22 @@
 	clock-frequency = <100000>;
 };
 
+&mcspi1 {
+	status = "disabled";
+};
+
+&mcspi2 {
+	status = "disabled";
+};
+
+&mcspi3 {
+	status = "disabled";
+};
+
+&mcspi4 {
+	status = "disabled";
+};
+
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
@@ -821,35 +841,35 @@
 };
 
 &mcbsp1 { /* FM Transceiver PCM */
-	status = "ok";
+	status = "okay";
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp1_pins>;
 };
 
 &mcbsp2 { /* TPS65950 I2S */
-	status = "ok";
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
 };
 
 &mcbsp3 { /* Bluetooth PCM */
-	status = "ok";
+	status = "okay";
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp3_pins>;
 };
 
 &mcbsp4 { /* GSM voice PCM */
-	status = "ok";
+	status = "okay";
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp4_pins>;
 };
 
 &hdqw1w {
-        pinctrl-names = "default";
-        pinctrl-0 = <&hdq_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdq_pins>;
 };
 
 /* image signal processor within OMAP3 SoC */
diff --git a/arch/arm/boot/dts/omap3-gta04a3.dts b/arch/arm/boot/dts/ti/omap/omap3-gta04a3.dts
index bfae1a9ceeac..bfae1a9ceeac 100644
--- a/arch/arm/boot/dts/omap3-gta04a3.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-gta04a3.dts
diff --git a/arch/arm/boot/dts/omap3-gta04a4.dts b/arch/arm/boot/dts/ti/omap/omap3-gta04a4.dts
index f1cf24d55e6f..f1cf24d55e6f 100644
--- a/arch/arm/boot/dts/omap3-gta04a4.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-gta04a4.dts
diff --git a/arch/arm/boot/dts/omap3-gta04a5.dts b/arch/arm/boot/dts/ti/omap/omap3-gta04a5.dts
index fd84bbf3b9cc..8bd6b4b1f30b 100644
--- a/arch/arm/boot/dts/omap3-gta04a5.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-gta04a5.dts
@@ -37,7 +37,7 @@
 };
 
 &gpio5 {
-	irda_en {
+	irda-en-hog {
 		gpio-hog;
 		gpios = <(175-160) GPIO_ACTIVE_HIGH>;
 		output-high;	/* activate gpio_175 to disable IrDA receiver */
@@ -45,41 +45,46 @@
 };
 
 &omap3_pmx_core {
-	bt_pins: pinmux_bt_pins {
+	bt_pins: bt-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4)	/* mmc2_dat5 = mmc3_dat1 = gpio137 */
 		>;
 	};
 
-	wlan_pins: pinmux_wlan_pins {
+	wlan_pins: wlan-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4)	/* mmc2_dat6 = mmc3_dat2 = gpio138 */
 		>;
 	};
 
-	wlan_irq_pin: pinmux_wlan_irq_pin {
+	wlan_irq_pin: wlan-irq-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE4)	/* mmc2_dat7 = mmc3_dat3 = gpio139 */
 		>;
 	};
 
-	irda_pins: pinmux_irda {
+	irda_pins: irda-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d0, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* mcspi1_cs1 = gpio175 */
 		>;
 	};
 
-	pps_pins: pinmux_pps_pins {
+	pps_pins: pps-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT | MUX_MODE4) /* gpin114 */
 		>;
 	};
 
+	bno050_pins: pinmux-bno050-pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2136, PIN_INPUT | MUX_MODE4) /* gpin113 */
+		>;
+	};
 };
 
 /*
  * for WL183x module see
- * Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
+ * Documentation/devicetree/bindings/net/wireless/ti,wlcore.yaml
  */
 
 &wifi_pwrseq {
@@ -115,17 +120,17 @@
 	/delete-node/ itg3200@68;
 	/delete-node/ hmc5843@1e;
 
-	bmg160@69 {
+	gyrometer@69 {
 		compatible = "bosch,bmg160";
 		reg = <0x69>;
 	};
 
-	bmc150@10 {
+	accelerometer@10 {
 		compatible = "bosch,bmc150_accel";
 		reg = <0x10>;
 	};
 
-	bmc150@12 {
+	magnetometer@12 {
 		compatible = "bosch,bmc150_magn";
 		reg = <0x12>;
 	};
@@ -133,5 +138,15 @@
 	bme280@76 {
 		compatible = "bosch,bme280";
 		reg = <0x76>;
+		vdda-supply = <&vio>;
+		vddd-supply = <&vio>;
+	};
+
+	imu@29 {
+		compatible = "bosch,bno055";
+		reg = <0x29>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bno050_pins>;
+		/* interrupt at &gpio4 17 */
 	};
 };
diff --git a/arch/arm/boot/dts/omap3-gta04a5one.dts b/arch/arm/boot/dts/ti/omap/omap3-gta04a5one.dts
index 9db9fe67cd63..1e5703d1b02e 100644
--- a/arch/arm/boot/dts/omap3-gta04a5one.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-gta04a5one.dts
@@ -5,10 +5,12 @@
 
 #include "omap3-gta04a5.dts"
 
-&omap3_pmx_core {
+/ {
 	model = "Goldelico GTA04A5/Letux 2804 with OneNAND";
+};
 
-	gpmc_pins: pinmux_gpmc_pins {
+&omap3_pmx_core {
+	gpmc_pins: gpmc-pins {
 		pinctrl-single,pins = <
 
 			/* address lines */
diff --git a/arch/arm/boot/dts/omap3-ha-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-ha-common.dtsi
index 33132855d517..3a258a692757 100644
--- a/arch/arm/boot/dts/omap3-ha-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-ha-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  * Copyright (C) 2014 Stefan Roese <sr@denx.de>
  */
 
@@ -17,43 +17,43 @@
 };
 
 &omap3_pmx_core {
-	sound2_pins: pinmux_sound2_pins {
+	sound2_pins: sound2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x209e, PIN_OUTPUT | MUX_MODE4)	/* gpmc_d8 gpio_44 */
 		>;
 	};
 
-	led_blue_pins: pinmux_led_blue_pins {
+	led_blue_pins: led-blue-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2110, PIN_OUTPUT | MUX_MODE4)	/* cam_xclka gpio_96, LED blue */
 		>;
 	};
 
-	led_green_pins: pinmux_led_green_pins {
+	led_green_pins: led-green-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2126, PIN_OUTPUT | MUX_MODE4)	/* cam_d8 gpio_107, LED green */
 		>;
 	};
 
-	led_red_pins: pinmux_led_red_pins {
+	led_red_pins: led-red-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x212e, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* cam_xclkb gpio_111, LED red */
 		>;
 	};
 
-	poweroff_pins: pinmux_poweroff_pins {
+	poweroff_pins: poweroff-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* i2c2_scl gpio_168 */
 		>;
 	};
 
-	powerdown_input_pins: pinmux_powerdown_input_pins {
+	powerdown_input_pins: powerdown-input-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT_PULLUP | MUX_MODE4)	/* i2c2_sda gpio_183 */
 		>;
 	};
 
-	fpga_boot0_pins: fpga_boot0_pins {
+	fpga_boot0_pins: fpga-boot0-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE4)	/* cam_d2 gpio_101 */
 			OMAP3_CORE1_IOPAD(0x211c, PIN_OUTPUT | MUX_MODE4)	/* cam_d3 gpio_102 */
@@ -62,7 +62,7 @@
 		>;
 	};
 
-	fpga_boot1_pins: fpga_boot1_pins {
+	fpga_boot1_pins: fpga-boot1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE4)	/* gpmc_d10 gpio_46 */
 			OMAP3_CORE1_IOPAD(0x20a4, PIN_OUTPUT | MUX_MODE4)	/* gpmc_d11 gpio_47 */
diff --git a/arch/arm/boot/dts/omap3-ha-lcd.dts b/arch/arm/boot/dts/ti/omap/omap3-ha-lcd.dts
index c9ecbc45c8e2..94f6b7931e33 100644
--- a/arch/arm/boot/dts/omap3-ha-lcd.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-ha-lcd.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  * Copyright (C) 2014 Stefan Roese <sr@denx.de>
  */
 
@@ -24,19 +24,19 @@
 		&touchscreen_wake_pins
 	>;
 
-	touchscreen_irq_pins: pinmux_touchscreen_irq_pins {
+	touchscreen_irq_pins: touchscreen-irq-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpio_136, Touchscreen IRQ */
 		>;
 	};
 
-	touchscreen_wake_pins: pinmux_touchscreen_wake_pins {
+	touchscreen_wake_pins: touchscreen-wake-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x212c, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* gpio_110, Touchscreen Wake */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -69,13 +69,13 @@
 		>;
 	};
 
-	lte430_pins: pinmux_lte430_pins {
+	lte430_pins: lte430-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat6.gpio_138 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat7.gpio_139 */
 		>;
@@ -100,7 +100,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
diff --git a/arch/arm/boot/dts/omap3-ha.dts b/arch/arm/boot/dts/ti/omap/omap3-ha.dts
index 35c4e15abeb7..19e471eb3b4e 100644
--- a/arch/arm/boot/dts/omap3-ha.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-ha.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  * Copyright (C) 2014 Stefan Roese <sr@denx.de>
  */
 
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/ti/omap/omap3-igep.dtsi
index 5de2be9bbe6f..e068ecf86b8f 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep.dtsi
@@ -2,7 +2,7 @@
 /*
  * Common device tree for IGEP boards based on AM/DM37x
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 /dts-v1/;
@@ -34,28 +34,28 @@
 };
 
 &omap3_pmx_core {
-	gpmc_pins: pinmux_gpmc_pins {
+	gpmc_pins: gpmc-pins {
 		pinctrl-single,pins = <
 			/* OneNAND seems to require PIN_INPUT on clock. */
                         OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0)	/* uart1_rx.uart1_rx */
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)	/* uart1_tx.uart1_tx */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)	/* uart3_rx.uart3_rx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx.uart3_tx */
 		>;
 	};
 
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)	/* mcbsp2_fsx.mcbsp2_fsx */
 			OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)	/* mcbsp2_clkx.mcbsp2_clkx */
@@ -64,7 +64,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -75,7 +75,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
@@ -86,14 +86,14 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)	/* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)	/* i2c1_sda.i2c1_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl.i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda.i2c3_sda */
@@ -111,7 +111,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,mt29c4g96maz";
+		linux,mtd-name = "micron,mt29c4g96maz";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/omap3-igep0020-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-igep0020-common.dtsi
index 91caa50b74c4..13f434625407 100644
--- a/arch/arm/boot/dts/omap3-igep0020-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep0020-common.dtsi
@@ -2,7 +2,7 @@
 /*
  * Common Device Tree Source for IGEPv2
  *
- * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) 2014 Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 
@@ -107,13 +107,13 @@
 		&dss_dpi_pins
 	>;
 
-	tfp410_pins: pinmux_tfp410_pins {
+	tfp410_pins: tfp410-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4)   /* hdq_sio.gpio_170 */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -146,7 +146,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)	/* uart2_cts.uart2_cts */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)	/* uart2_rts .uart2_rts*/
@@ -155,7 +155,7 @@
 		>;
 	};
 
-	smsc9221_pins: pinmux_smsc9221_pins {
+	smsc9221_pins: smsc9221-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4)	/* mcspi1_cs2.gpio_176 */
 		>;
@@ -168,7 +168,7 @@
 		&hsusbb1_pins
 	>;
 
-	hsusbb1_pins: pinmux_hsusbb1_pins {
+	hsusbb1_pins: hsusbb1-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25da, PIN_OUTPUT | MUX_MODE3)		/* etk_ctl.hsusb1_clk */
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3)		/* etk_clk.hsusb1_stp */
@@ -185,7 +185,7 @@
 		>;
 	};
 
-	leds_pins: pinmux_leds_pins {
+	leds_pins: leds-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25f4, PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
 			OMAP3630_CORE2_IOPAD(0x25f6, PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
@@ -193,7 +193,7 @@
 		>;
 	};
 
-	mmc1_wp_pins: pinmux_mmc1_cd_pins {
+	mmc1_wp_pins: mmc1-cd-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT | MUX_MODE4)   /* etk_d15.gpio_29 */
 		>;
@@ -245,7 +245,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	port {
 		dpi_out: endpoint {
diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/ti/omap/omap3-igep0020-rev-f.dts
index 567232584f08..316e8e6b39cd 100644
--- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep0020-rev-f.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for IGEPv2 Rev. F (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 
@@ -10,7 +10,7 @@
 
 / {
 	model = "IGEPv2 Rev. F (TI OMAP AM/DM37x)";
-	compatible = "isee,omap3-igep0020-rev-f", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "isee,omap3-igep0020-rev-f", "ti,omap3630", "ti,omap3";
 
 	/* Regulator to trigger the WL_EN signal of the Wifi module */
 	lbep5clwmc_wlen: regulator-lbep5clwmc-wlen {
@@ -24,7 +24,7 @@
 };
 
 &omap3_pmx_core {
-	lbep5clwmc_pins: pinmux_lbep5clwmc_pins {
+	lbep5clwmc_pins: lbep5clwmc-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT | MUX_MODE4)	/* mcspi1_cs3.gpio_177 - W_IRQ */
 			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 - BT_EN */
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/ti/omap/omap3-igep0020.dts
index e341535a7162..232cf9187822 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep0020.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for IGEPv2 Rev. C (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 
@@ -10,7 +10,7 @@
 
 / {
 	model = "IGEPv2 Rev. C (TI OMAP AM/DM37x)";
-	compatible = "isee,omap3-igep0020", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "isee,omap3-igep0020", "ti,omap3630", "ti,omap3";
 
 	vmmcsdio_fixed: fixedregulator-mmcsdio {
 		compatible = "regulator-fixed";
@@ -27,7 +27,7 @@
 };
 
 &omap3_pmx_core {
-	lbee1usjyc_pins: pinmux_lbee1usjyc_pins {
+	lbee1usjyc_pins: lbee1usjyc-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 - RESET_N_W */
 			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat6.gpio_138 - WIFI_PDN */
diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-igep0030-common.dtsi
index 71b0ae807ecd..d434f75aadac 100644
--- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep0030-common.dtsi
@@ -2,7 +2,7 @@
 /*
  * Common Device Tree Source for IGEP COM MODULE
  *
- * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) 2014 Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 
@@ -31,7 +31,7 @@
 		};
 	};
 
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;		/* gpio_54 */
 		#phy-cells = <0>;
@@ -42,7 +42,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&hsusb2_pins>;
 
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
@@ -53,7 +53,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)	/* mcbsp3_dx.uart2_cts */
 			OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1)	/* mcbsp3_dr.uart2_rts */
@@ -67,7 +67,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&hsusb2_core2_pins>;
 
-	hsusb2_core2_pins: pinmux_hsusb2_core2_pins {
+	hsusb2_core2_pins: hsusb2-core2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		      /* etk_d10.hsusb2_clk */
 			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		      /* etk_d11.hsusb2_stp */
@@ -78,7 +78,7 @@
 		>;
 	};
 
-	leds_core2_pins: pinmux_leds_core2_pins {
+	leds_core2_pins: leds-core2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)	/* etk_d2.gpio_16 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/ti/omap/omap3-igep0030-rev-g.dts
index df6ba1219830..fddd7c86fec4 100644
--- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep0030-rev-g.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) 2014 Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 
@@ -10,7 +10,7 @@
 
 / {
 	model = "IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)";
-	compatible = "isee,omap3-igep0030-rev-g", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "isee,omap3-igep0030-rev-g", "ti,omap3630", "ti,omap3";
 
 	/* Regulator to trigger the WL_EN signal of the Wifi module */
 	lbep5clwmc_wlen: regulator-lbep5clwmc-wlen {
@@ -24,7 +24,7 @@
 };
 
 &omap3_pmx_core {
-	lbep5clwmc_pins: pinmux_lbep5clwmc_pins {
+	lbep5clwmc_pins: lbep5clwmc-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 - W_IRQ */
 			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 - BT_EN */
@@ -32,7 +32,7 @@
 		>;
 	};
 
-	leds_pins: pinmux_leds_pins {
+	leds_pins: leds-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)	/* i2c2_scl.gpio_168 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/ti/omap/omap3-igep0030.dts
index 32f31035daa2..e3f99dbef2a1 100644
--- a/arch/arm/boot/dts/omap3-igep0030.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-igep0030.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree Source for IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@dowhile0.org>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  */
 
@@ -10,7 +10,7 @@
 
 / {
 	model = "IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)";
-	compatible = "isee,omap3-igep0030", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "isee,omap3-igep0030", "ti,omap3630", "ti,omap3";
 
 	vmmcsdio_fixed: fixedregulator-mmcsdio {
 		compatible = "regulator-fixed";
@@ -27,7 +27,7 @@
 };
 
 &omap3_pmx_core {
-	lbee1usjyc_pins: pinmux_lbee1usjyc_pins {
+	lbee1usjyc_pins: lbee1usjyc-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 - RESET_N_W */
 			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat6.gpio_138 - WIFI_PDN */
diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/ti/omap/omap3-ldp.dts
index ec9ba04ef43b..bb6fab9fa47d 100644
--- a/arch/arm/boot/dts/omap3-ldp.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-ldp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -103,7 +103,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,nand";
+		linux,mtd-name = "micron,nand";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
@@ -215,15 +215,15 @@
 };
 
 &mmc2 {
-	status="disabled";
+	status = "disabled";
 };
 
 &mmc3 {
-	status="disabled";
+	status = "disabled";
 };
 
 &omap3_pmx_core {
-	gpio_key_pins: pinmux_gpio_key_pins {
+	gpio_key_pins: gpio-key-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE4)	/* cam_d2.gpio_101 */
 			OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE4)	/* cam_d3.gpio_102 */
@@ -237,7 +237,7 @@
 		>;
 	};
 
-	musb_pins: pinmux_musb_pins {
+	musb_pins: musb-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)	/* hsusb0_clk.hsusb0_clk */
 			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0)	/* hsusb0_data0.hsusb0_data0 */
@@ -254,7 +254,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
@@ -301,5 +301,5 @@
 
 &vaux1 {
 	/* Needed for ads7846 */
-        regulator-name = "vcc";
+	regulator-name = "vcc";
 };
diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/ti/omap/omap3-lilly-a83x.dtsi
index 73d477898ec2..565a6c0e7b37 100644
--- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-lilly-a83x.dtsi
@@ -54,19 +54,19 @@
 &omap3_pmx_wkup {
 	pinctrl-names = "default";
 
-	lan9221_pins: pinmux_lan9221_pins {
+	lan9221_pins: lan9221-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4)   /* reserved.gpio_129 */
 		>;
 	};
 
-	tsc2048_pins: pinmux_tsc2048_pins {
+	tsc2048_pins: tsc2048-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a16, PIN_INPUT_PULLUP | MUX_MODE4)   /* sys_boot6.gpio_8 */
 		>;
 	};
 
-	mmc1cd_pins: pinmux_mmc1cd_pins {
+	mmc1cd_pins: mmc1cd-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4)   /* reserved.gpio_126 */
 		>;
@@ -76,7 +76,7 @@
 &omap3_pmx_core {
 	pinctrl-names = "default";
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)   /* uart1_tx.uart1_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0)   /* uart1_rts.uart1_rts */
@@ -85,42 +85,42 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1)   /* mcbsp3_clkx.uart2_tx */
 			OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1)    /* mcbsp3_fsx.uart2_rx */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)    /* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)   /* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba ,PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc ,PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_sda.i2c1_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
 			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
 		>;
 	};
 
-	hsusb1_pins: pinmux_hsusb1_pins {
+	hsusb1_pins: hsusb1-pins {
 		pinctrl-single,pins = <
 
 			/* GPIO 182 controls USB-Hub reset. But USB-Phy its
@@ -132,7 +132,7 @@
 		>;
 	};
 
-	hsusb_otg_pins: pinmux_hsusb_otg_pins {
+	hsusb_otg_pins: hsusb-otg-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)   /* hsusb0_clk.hsusb0_clk */
 			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)  /* hsusb0_stp.hsusb0_stp */
@@ -149,7 +149,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_cmd.sdmmc1_cmd */
@@ -160,7 +160,7 @@
 		>;
 	};
 
-	spi2_pins: pinmux_spi2_pins {
+	spi2_pins: spi2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_clk.mcspi2_clk */
 			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_simo.mcspi2_simo */
@@ -173,7 +173,7 @@
 &omap3_pmx_core2 {
 	pinctrl-names = "default";
 
-	hsusb1_2_pins: pinmux_hsusb1_2_pins {
+	hsusb1_2_pins: hsusb1-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3)  /* etk_clk.hsusb1_stp */
 			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT | MUX_MODE3)   /* etk_ctl.hsusb1_clk */
@@ -190,7 +190,7 @@
 		>;
 	};
 
-	gpio1_pins: pinmux_gpio1_pins {
+	gpio1_pins: gpio1-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4)   /* etk_d15.gpio_29 */
 		>;
@@ -311,7 +311,7 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <8 0>;   /* boot6 / gpio_8 */
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_vcc3>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tsc2048_pins>;
@@ -372,7 +372,7 @@
 		gpmc,device-width = <2>;
 		gpmc,wait-pin = <0>;
 		gpmc,wait-monitoring-ns = <0>;
-		gpmc,burst-length= <4>;
+		gpmc,burst-length = <4>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <100>;
 		gpmc,cs-wr-off-ns = <100>;
diff --git a/arch/arm/boot/dts/omap3-lilly-dbb056.dts b/arch/arm/boot/dts/ti/omap/omap3-lilly-dbb056.dts
index ecb4ef738e07..0891c6682a67 100644
--- a/arch/arm/boot/dts/omap3-lilly-dbb056.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-lilly-dbb056.dts
@@ -8,7 +8,7 @@
 
 / {
 	model = "INCOstartec LILLY-DBB056 (DM3730)";
-	compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap3630", "ti,omap3";
 };
 
 &twl {
@@ -24,25 +24,25 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&lcd_pins>;
 
-	lan9117_pins: pinmux_lan9117_pins {
+	lan9117_pins: lan9117-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4)   /* cam_fld.gpio_98 */
 		>;
 	};
 
-	gpio4_pins: pinmux_gpio4_pins {
+	gpio4_pins: gpio4-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4)   /* cam_xclkb.gpio_111 -> sja1000 IRQ */
 		>;
 	};
 
-	gpio5_pins: pinmux_gpio5_pins {
+	gpio5_pins: gpio5-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218c, PIN_OUTPUT | PIN_OFF_OUTPUT_HIGH | MUX_MODE4)   /* mcbsp1_clk.gpio_156 -> enable DSS */
 		>;
 	};
 
-	lcd_pins: pinmux_lcd_pins {
+	lcd_pins: lcd-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -69,7 +69,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_cmd.sdmmc2_cmd */
@@ -86,7 +86,7 @@
 		>;
 	};
 
-	spi1_pins: pinmux_spi1_pins {
+	spi1_pins: spi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)   /* mcspi1_clk.mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)   /* mcspi1_simo.mcspi1_simo */
diff --git a/arch/arm/boot/dts/omap3-n9.dts b/arch/arm/boot/dts/ti/omap/omap3-n9.dts
index 2495a696cec6..a3cf3f443785 100644
--- a/arch/arm/boot/dts/omap3-n9.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-n9.dts
@@ -12,7 +12,7 @@
 
 / {
 	model = "Nokia N9";
-	compatible = "nokia,omap3-n9", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "nokia,omap3-n9", "ti,omap3630", "ti,omap3";
 };
 
 &i2c2 {
@@ -23,7 +23,6 @@
 		vana-supply = <&vaux3>;
 		clocks = <&isp 0>;
 		clock-frequency = <9600000>;
-		nokia,nvm-size = <(16 * 64)>;
 		flash-leds = <&as3645a_flash &as3645a_indicator>;
 		port {
 			smia_1_1: endpoint {
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/ti/omap/omap3-n900.dts
index a638e059135b..d33485341251 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-n900.dts
@@ -8,6 +8,8 @@
 
 #include "omap34xx.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/video-interfaces.h>
 
 /*
  * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
@@ -19,7 +21,11 @@
  * but it is not widely used and to prevent kernel crash rather AES is disabled.
  * There is also no runtime detection code if AES is disabled in L3 firewall...
  */
-&aes {
+&aes1_target {
+	status = "disabled";
+};
+
+&aes2_target {
 	status = "disabled";
 };
 
@@ -44,7 +50,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		heartbeat {
+		led-heartbeat {
 			label = "debug::sleep";
 			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;  /* 162 */
 			linux,default-trigger = "default-on";
@@ -105,6 +111,14 @@
 			linux,code = <SW_FRONT_PROXIMITY>;
 			linux,can-disable;
 		};
+
+		machine_cover {
+			label = "Machine Cover";
+			gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* 160 */
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_MACHINE_COVER>;
+			linux,can-disable;
+		};
 	};
 
 	isp1707: isp1707 {
@@ -143,7 +157,7 @@
 		io-channel-names = "temp", "bsi", "vbat";
 	};
 
-	pwm9: dmtimer-pwm {
+	pwm9: pwm-9 {
 		compatible = "ti,omap-dmtimer-pwm";
 		#pwm-cells = <3>;
 		ti,timers = <&timer9>;
@@ -181,7 +195,7 @@
 
 			csi_isp: endpoint {
 				remote-endpoint = <&csi_cam1>;
-				bus-type = <3>; /* CCP2 */
+				bus-type = <MEDIA_BUS_TYPE_CCP2>;
 				clock-lanes = <1>;
 				data-lanes = <0>;
 				lane-polarity = <0 0>;
@@ -195,7 +209,7 @@
 &omap3_pmx_core {
 	pinctrl-names = "default";
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)		/* uart2_cts */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts */
@@ -204,14 +218,14 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx */
 		>;
 	};
 
-	ethernet_pins: pinmux_ethernet_pins {
+	ethernet_pins: ethernet-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* gpmc_ncs3.gpio_54 */
 			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4)		/* dss_data16.gpio_86 */
@@ -219,61 +233,61 @@
 		>;
 	};
 
-	gpmc_pins: pinmux_gpmc_pins {
+	gpmc_pins: gpmc-pins {
 		pinctrl-single,pins = <
 
 			/* address lines */
-                        OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a1.gpmc_a1 */
-                        OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a2.gpmc_a2 */
-                        OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a3.gpmc_a3 */
+			OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a1.gpmc_a1 */
+			OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a2.gpmc_a2 */
+			OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a3.gpmc_a3 */
 
 			/* data lines, gpmc_d0..d7 not muxable according to TRM */
-                        OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0)        /* gpmc_d8.gpmc_d8 */
-                        OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0)        /* gpmc_d9.gpmc_d9 */
-                        OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0)        /* gpmc_d10.gpmc_d10 */
-                        OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0)        /* gpmc_d11.gpmc_d11 */
-                        OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0)        /* gpmc_d12.gpmc_d12 */
-                        OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0)        /* gpmc_d13.gpmc_d13 */
-                        OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0)        /* gpmc_d14.gpmc_d14 */
-                        OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0)        /* gpmc_d15.gpmc_d15 */
+			OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0)        /* gpmc_d8.gpmc_d8 */
+			OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0)        /* gpmc_d9.gpmc_d9 */
+			OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0)        /* gpmc_d10.gpmc_d10 */
+			OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0)        /* gpmc_d11.gpmc_d11 */
+			OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0)        /* gpmc_d12.gpmc_d12 */
+			OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0)        /* gpmc_d13.gpmc_d13 */
+			OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0)        /* gpmc_d14.gpmc_d14 */
+			OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0)        /* gpmc_d15.gpmc_d15 */
 
 			/*
 			 * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
 			 * according to TRM. OneNAND seems to require PIN_INPUT on clock.
 			 */
-                        OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0)       /* gpmc_ncs1.gpmc_ncs1 */
-                        OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
-		>;
+			OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0)       /* gpmc_ncs1.gpmc_ncs1 */
+			OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
+			>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)		/* i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)		/* i2c1_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)		/* i2c2_scl */
 			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)		/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)		/* i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)		/* i2c3_sda */
 		>;
 	};
 
-	debug_leds: pinmux_debug_led_pins {
+	debug_leds: debug-led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_clkx.gpio_162 */
 		>;
 	};
 
-	mcspi4_pins: pinmux_mcspi4_pins {
+	mcspi4_pins: mcspi4-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
 			OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
@@ -282,7 +296,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd */
@@ -293,7 +307,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd */
@@ -308,13 +322,13 @@
 		>;
 	};
 
-	acx565akm_pins: pinmux_acx565akm_pins {
+	acx565akm_pins: acx565akm-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4)		/* RX51_LCD_RESET_GPIO */
 		>;
 	};
 
-	dss_sdi_pins: pinmux_dss_sdi_pins {
+	dss_sdi_pins: dss-sdi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1)   /* dss_data10.sdi_dat1n */
 			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1)   /* dss_data11.sdi_dat1p */
@@ -326,14 +340,14 @@
 		>;
 	};
 
-	wl1251_pins: pinmux_wl1251 {
+	wl1251_pins: wl1251-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4)		/* gpio 87 => wl1251 enable */
 			OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4)		/* gpio 42 => wl1251 irq */
 		>;
 	};
 
-	ssi_pins: pinmux_ssi {
+	ssi_pins: ssi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1)	/* ssi1_rdy_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)		/* ssi1_flag_tx */
@@ -346,7 +360,7 @@
 		>;
 	};
 
-	modem_pins: pinmux_modem {
+	modem_pins: modem-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4)		/* gpio 70 => cmt_apeslpx */
 			OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4)		/* gpio 72 => ape_rst_rq */
@@ -357,7 +371,7 @@
 		>;
 	};
 
-	camera_pins: pinmux_camera {
+	camera_pins: camera-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x210c, PIN_OUTPUT | MUX_MODE7)       /* cam_hs */
 			OMAP3_CORE1_IOPAD(0x210e, PIN_OUTPUT | MUX_MODE7)       /* cam_vs */
@@ -482,6 +496,11 @@
 	regulator-always-on;
 };
 
+/* First two dma channels are reserved on secure omap3 */
+&sdma {
+	dma-channel-mask = <0xfffffffc>;
+};
+
 &twl {
 	twl_audio: audio {
 		compatible = "ti,twl4030-audio";
@@ -550,8 +569,8 @@
 };
 
 &twl_gpio {
-	ti,pullups	= <0x0>;
-	ti,pulldowns	= <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
+	ti,pullups = <0x0>;
+	ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
 };
 
 &i2c2 {
@@ -613,63 +632,92 @@
 	};
 
 	lp5523: lp5523@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		compatible = "national,lp5523";
 		reg = <0x32>;
 		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
-		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
+		enable-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
 
-		chan0 {
+		led@0 {
+			reg = <0>;
 			chan-name = "lp5523:kb1";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan1 {
+		led@1 {
+			reg = <1>;
 			chan-name = "lp5523:kb2";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan2 {
+		led@2 {
+			reg = <2>;
 			chan-name = "lp5523:kb3";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan3 {
+		led@3 {
+			reg = <3>;
 			chan-name = "lp5523:kb4";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan4 {
+		led@4 {
+			reg = <4>;
 			chan-name = "lp5523:b";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan5 {
+		led@5 {
+			reg = <5>;
 			chan-name = "lp5523:g";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan6 {
+		led@6 {
+			reg = <6>;
 			chan-name = "lp5523:r";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan7 {
+		led@7 {
+			reg = <7>;
 			chan-name = "lp5523:kb5";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan8 {
+		led@8 {
+			reg = <8>;
 			chan-name = "lp5523:kb6";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 	};
 
@@ -691,12 +739,12 @@
 
 	si4713: si4713@63 {
 		compatible = "silabs,si4713";
-                reg = <0x63>;
+		reg = <0x63>;
 
-                interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
-                reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
-                vio-supply = <&vio>;
-                vdd-supply = <&vaux1>;
+		interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
+		reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
+		vio-supply = <&vio>;
+		vdd-supply = <&vaux1>;
 	};
 
 	bq24150a: bq24150a@6b {
@@ -720,56 +768,20 @@
 
 	clock-frequency = <400000>;
 
-	lis302dl: lis3lv02d@1d {
-		compatible = "st,lis3lv02d";
+	accelerometer@1d {
+		compatible = "st,lis302dl";
 		reg = <0x1d>;
 
-		Vdd-supply = <&vaux1>;
-		Vdd_IO-supply = <&vio>;
+		vdd-supply = <&vaux1>;
+		vddio-supply = <&vio>;
 
 		interrupt-parent = <&gpio6>;
-		interrupts = <21 20>; /* 181 and 180 */
+		interrupts = <21 IRQ_TYPE_EDGE_RISING>,
+			     <20 IRQ_TYPE_EDGE_RISING>; /* 181 and 180 */
 
-		/* click flags */
-		st,click-single-x;
-		st,click-single-y;
-		st,click-single-z;
-
-		/* Limits are 0.5g * value */
-		st,click-threshold-x = <8>;
-		st,click-threshold-y = <8>;
-		st,click-threshold-z = <10>;
-
-		/* Click must be longer than time limit */
-		st,click-time-limit = <9>;
-
-		/* Kind of debounce filter */
-		st,click-latency = <50>;
-
-		/* Interrupt line 2 for click detection */
-		st,irq2-click;
-
-		st,wakeup-x-hi;
-		st,wakeup-y-hi;
-		st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */
-
-		st,wakeup2-z-hi;
-		st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */
-
-		st,hipass1-disable;
-		st,hipass2-disable;
-
-		st,axis-x = <1>;    /* LIS3_DEV_X */
-		st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */
-		st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */
-
-		st,min-limit-x = <(-32)>;
-		st,min-limit-y = <3>;
-		st,min-limit-z = <3>;
-
-		st,max-limit-x = <(-3)>;
-		st,max-limit-y = <32>;
-		st,max-limit-z = <32>;
+		mount-matrix =	 "-1",  "0",  "0",
+				  "0",  "1",  "0",
+				  "0",  "0",  "1";
 	};
 
 	cam1: camera@3e {
@@ -788,7 +800,7 @@
 
 		port {
 			csi_cam1: endpoint {
-				bus-type = <3>; /* CCP2 */
+				bus-type = <MEDIA_BUS_TYPE_CCP2>;
 				strobe = <1>;
 				clock-inv = <0>;
 				crc = <1>;
@@ -814,10 +826,6 @@
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&vmmc1>;
 	bus-width = <4>;
-	/* For debugging, it is often good idea to remove this GPIO.
-	   It means you can remove back cover (to reboot by removing
-	   battery) and still use the MMC card. */
-	cd-gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* 160 */
 };
 
 /* most boards use vaux3, only some old versions use vmmc2 instead */
@@ -849,34 +857,46 @@
 		compatible = "ti,omap2-onenand";
 		reg = <0 0 0x20000>;	/* CS0, offset 0, IO size 128K */
 
+		/*
+		 * These timings are based on CONFIG_OMAP_GPMC_DEBUG=y reported
+		 * bootloader set values when booted with v5.1
+		 * (OneNAND Manufacturer: Samsung):
+		 *
+		 *   cs0 GPMC_CS_CONFIG1: 0xfb001202
+		 *   cs0 GPMC_CS_CONFIG2: 0x00111100
+		 *   cs0 GPMC_CS_CONFIG3: 0x00020200
+		 *   cs0 GPMC_CS_CONFIG4: 0x11001102
+		 *   cs0 GPMC_CS_CONFIG5: 0x03101616
+		 *   cs0 GPMC_CS_CONFIG6: 0x90060000
+		 */
 		gpmc,sync-read;
 		gpmc,sync-write;
 		gpmc,burst-length = <16>;
 		gpmc,burst-read;
 		gpmc,burst-wrap;
 		gpmc,burst-write;
-		gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
-		gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
+		gpmc,device-width = <2>;
+		gpmc,mux-add-data = <2>;
 		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <87>;
-		gpmc,cs-wr-off-ns = <87>;
+		gpmc,cs-rd-off-ns = <102>;
+		gpmc,cs-wr-off-ns = <102>;
 		gpmc,adv-on-ns = <0>;
-		gpmc,adv-rd-off-ns = <10>;
-		gpmc,adv-wr-off-ns = <10>;
-		gpmc,oe-on-ns = <15>;
-		gpmc,oe-off-ns = <87>;
+		gpmc,adv-rd-off-ns = <12>;
+		gpmc,adv-wr-off-ns = <12>;
+		gpmc,oe-on-ns = <12>;
+		gpmc,oe-off-ns = <102>;
 		gpmc,we-on-ns = <0>;
-		gpmc,we-off-ns = <87>;
-		gpmc,rd-cycle-ns = <112>;
-		gpmc,wr-cycle-ns = <112>;
-		gpmc,access-ns = <81>;
-		gpmc,page-burst-access-ns = <15>;
+		gpmc,we-off-ns = <102>;
+		gpmc,rd-cycle-ns = <132>;
+		gpmc,wr-cycle-ns = <132>;
+		gpmc,access-ns = <96>;
+		gpmc,page-burst-access-ns = <18>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,wait-monitoring-ns = <0>;
-		gpmc,clk-activation-ns = <5>;
-		gpmc,wr-data-mux-bus-ns = <30>;
-		gpmc,wr-access-ns = <81>;
+		gpmc,clk-activation-ns = <6>;
+		gpmc,wr-data-mux-bus-ns = <36>;
+		gpmc,wr-access-ns = <96>;
 		gpmc,sync-clk-ps = <15000>;
 
 		/*
@@ -1058,7 +1078,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_sdi_pins>;
@@ -1081,7 +1101,7 @@
 };
 
 &venc {
-	status = "ok";
+	status = "okay";
 
 	vdda-supply = <&vdac>;
 
@@ -1094,7 +1114,7 @@
 };
 
 &mcbsp2 {
-	status = "ok";
+	status = "okay";
 };
 
 &ssi_port1 {
diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/ti/omap/omap3-n950-n9.dtsi
index a075b63f3087..aa4fcdbedd8f 100644
--- a/arch/arm/boot/dts/omap3-n950-n9.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-n950-n9.dtsi
@@ -57,20 +57,20 @@
 };
 
 &omap3_pmx_core {
-	accelerator_pins: pinmux_accelerator_pins {
+	accelerator_pins: accelerator-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT | MUX_MODE4)	/* mcspi2_somi.gpio_180 -> LIS302 INT1 */
 			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT | MUX_MODE4)	/* mcspi2_cs0.gpio_181 -> LIS302 INT2 */
 		>;
 	};
 
-	debug_leds: pinmux_debug_led_pins {
+	debug_leds: debug-led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE4)       /* dss_data22.gpio_92 */
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
@@ -81,14 +81,14 @@
 		>;
 	};
 
-	wlan_pins: pinmux_wlan_pins {
+	wlan_pins: wlan-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE4) /* gpio 35 - wlan enable */
 			OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 - wlan irq */
 		>;
 	};
 
-	ssi_pins: pinmux_ssi_pins {
+	ssi_pins: ssi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1)            /* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)            /* ssi1_flag_tx */
@@ -101,7 +101,7 @@
 		>;
 	};
 
-	ssi_pins_idle: pinmux_ssi_pins_idle {
+	ssi_pins_idle: ssi-idle-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE7)            /* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE7)            /* ssi1_flag_tx */
@@ -114,7 +114,7 @@
 		>;
 	};
 
-	modem_pins1: pinmux_modem_core1_pins {
+	modem_pins1: modem-core1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x207a, PIN_INPUT | MUX_MODE4)	/* gpio_34 (ape_rst_rq) */
 			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE4)            /* gpio_88 (cmt_rst_rq) */
@@ -122,7 +122,7 @@
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)		/* uart2_cts */
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts */
@@ -133,7 +133,7 @@
 };
 
 &omap3_pmx_core2 {
-	modem_pins2: pinmux_modem_core2_pins {
+	modem_pins2: modem-core2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)         /* gpio_23 (cmt_en) */
 		>;
@@ -162,8 +162,8 @@
 };
 
 &twl_gpio {
-	ti,pullups	= <0x000001>; /* BIT(0) */
-	ti,pulldowns	= <0x008106>; /* BIT(1) | BIT(2) | BIT(8) | BIT(15) */
+	ti,pullups = <0x000001>; /* BIT(0) */
+	ti,pulldowns = <0x008106>; /* BIT(1) | BIT(2) | BIT(8) | BIT(15) */
 };
 
 &vdac {
@@ -341,6 +341,11 @@
 	status = "disabled";
 };
 
+/* RNG not directly accessible on N950/N9. */
+&rng_target {
+	status = "disabled";
+};
+
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
@@ -489,3 +494,11 @@
 		clock-names = "sysclk";
 	};
 };
+
+&aes1_target {
+	status = "disabled";
+};
+
+&aes2_target {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/omap3-n950.dts b/arch/arm/boot/dts/ti/omap/omap3-n950.dts
index 31d47a1fad84..b99f97880204 100644
--- a/arch/arm/boot/dts/omap3-n950.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-n950.dts
@@ -12,7 +12,7 @@
 
 / {
 	model = "Nokia N950";
-	compatible = "nokia,omap3-n950", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "nokia,omap3-n950", "ti,omap3630", "ti,omap3";
 
 	keys {
 		compatible = "gpio-keys";
@@ -30,7 +30,7 @@
 };
 
 &omap3_pmx_core {
-	keypad_slide_pins: pinmux_debug_led_pins {
+	keypad_slide_pins: debug-led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT | MUX_MODE4)       /* cam_d10.gpio_109 */
 		>;
@@ -38,7 +38,7 @@
 };
 
 &omap3_pmx_core {
-	spi4_pins: pinmux_spi4_pins {
+	spi4_pins: spi4-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
 			OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
@@ -49,7 +49,7 @@
 };
 
 &omap3_pmx_core {
-	dsi_pins: pinmux_dsi_pins {
+	dsi_pins: dsi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE1) /* dsi_dx0 - data0+ */
 			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE1) /* dsi_dy0 - data0- */
@@ -60,7 +60,7 @@
 		>;
 	};
 
-	display_pins: pinmux_display_pins {
+	display_pins: display-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20ca, PIN_INPUT | MUX_MODE4) /* gpio 62 - display te */
 			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 - display reset */
@@ -76,7 +76,6 @@
 		vana-supply = <&vaux3>;
 		clocks = <&isp 0>;
 		clock-frequency = <9600000>;
-		nokia,nvm-size = <(16 * 64)>;
 		flash-leds = <&as3645a_flash &as3645a_indicator>;
 		port {
 			smia_1_1: endpoint {
@@ -205,13 +204,13 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	vdda_video-supply = <&vdac>;
 };
 
 &dsi {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dsi_pins>;
@@ -225,8 +224,9 @@
 		};
 	};
 
-	lcd0: display {
+	lcd0: panel@0 {
 		compatible = "nokia,himalaya", "panel-dsi-cm";
+		reg = <0>;
 		label = "lcd0";
 
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-alto35-common.dtsi
index bb932913c9e3..7f1671bf3dfa 100644
--- a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-alto35-common.dtsi
@@ -17,19 +17,19 @@
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
-		gpio148 {
+		led-gpio148 {
 			label = "overo:red:gpio148";
 			gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>;		/* gpio 148 */
 		};
-		gpio150 {
+		led-gpio150 {
 			label = "overo:yellow:gpio150";
 			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;		/* gpio 150 */
 		};
-		gpio151 {
+		led-gpio151 {
 			label = "overo:blue:gpio151";
 			gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;		/* gpio 151 */
 		};
-		gpio170 {
+		led-gpio170 {
 			label = "overo:green:gpio170";
 			gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;		/* gpio 170 */
 		};
@@ -51,7 +51,7 @@
 };
 
 &omap3_pmx_core {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE4)	/* uart1_tx.gpio_148 */
 			OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4)	/* uart1_cts.gpio_150 */
@@ -62,7 +62,7 @@
 };
 
 &omap3_pmx_wkup {
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a18, PIN_INPUT | MUX_MODE4)		/* sys_clkout1.gpio_10 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-overo-alto35.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-alto35.dts
index 37c64dd5f672..37c64dd5f672 100644
--- a/arch/arm/boot/dts/omap3-overo-alto35.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-alto35.dts
diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-base.dtsi
index 971d3e250515..cc57626ea607 100644
--- a/arch/arm/boot/dts/omap3-overo-base.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-base.dtsi
@@ -14,10 +14,10 @@
 		reg = <0 0>;
 	};
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		overo {
+		led-1 {
 			label = "overo:blue:COM";
 			pwms = <&twl_pwmled 1 7812500>;
 			max-brightness = <127>;
@@ -44,7 +44,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;	/* gpio_183 */
 		vcc-supply = <&hsusb2_power>;
@@ -80,7 +80,7 @@
 			&hsusb2_pins
 	>;
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)	/* mcbsp3_dx.uart2_cts */
 			OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1)	/* mcbsp3_dr.uart2_rts */
@@ -89,14 +89,14 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)		/* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)		/* i2c1_sda.i2c1_sda */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
@@ -107,7 +107,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
@@ -119,14 +119,14 @@
 	};
 
 	/* WiFi/BT combo */
-	w3cbw003c_pins: pinmux_w3cbw003c_pins {
+	w3cbw003c_pins: w3cbw003c-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4)		/* gpmc_ncs3.gpio_54 */
 			OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)		/* uart3_rts_sd.gpio_164 */
 		>;
 	};
 
-	hsusb2_pins: pinmux_hsusb2_pins {
+	hsusb2_pins: hsusb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
 			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
@@ -222,7 +222,7 @@
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
-		linux,mtd-name= "micron,mt29c4g96maz";
+		linux,mtd-name = "micron,mt29c4g96maz";
 		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-chestnut43-common.dtsi
index 2d2c61d7aa86..0d0e62c00916 100644
--- a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-chestnut43-common.dtsi
@@ -17,12 +17,12 @@
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
-		heartbeat {
+		led-heartbeat {
 			label = "overo:red:gpio21";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;		/* gpio_21 */
 			linux,default-trigger = "heartbeat";
 		};
-		gpio22 {
+		led-gpio22 {
 			label = "overo:blue:gpio22";
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;		/* gpio_22 */
 		};
diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-chestnut43.dts
index d147d704b89f..bb53c76fff6c 100644
--- a/arch/arm/boot/dts/omap3-overo-chestnut43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-chestnut43.dts
@@ -18,14 +18,14 @@
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-common-dvi.dtsi
index c9e62e414abb..b1a800f2e940 100644
--- a/arch/arm/boot/dts/omap3-overo-common-dvi.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-common-dvi.dtsi
@@ -8,7 +8,7 @@
  */
 
 &omap3_pmx_core {
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -48,7 +48,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-common-lcd35.dtsi
index 185ce53de0ec..0da561a23f36 100644
--- a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-common-lcd35.dtsi
@@ -8,7 +8,7 @@
  */
 
 &omap3_pmx_core {
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -41,19 +41,19 @@
 		>;
 	};
 
-	lb035_pins: pinmux_lb035_pins {
+	lb035_pins: lb035-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4)	/* uart2_cts.gpio_144 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4)	/* uart2_rts.gpio_145 */
 		>;
 	};
 
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
@@ -63,7 +63,7 @@
 		>;
 	};
 
-	ads7846_pins: pinmux_ads7846_pins {
+	ads7846_pins: ads7846-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* csi2_dx1.gpio_114 */
 		>;
@@ -76,7 +76,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
@@ -149,7 +149,7 @@
 
 		interrupt-parent = <&gpio4>;
 		interrupts = <18 0>;			/* gpio_114 */
-		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-common-lcd43.dtsi
index 7fe0f9148232..981f02f088f8 100644
--- a/arch/arm/boot/dts/omap3-overo-common-lcd43.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-common-lcd43.dtsi
@@ -8,7 +8,7 @@
  */
 
 &omap3_pmx_core {
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -41,19 +41,19 @@
 		>;
 	};
 
-	lte430_pins: pinmux_lte430_pins {
+	lte430_pins: lte430-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4)	/* uart2_cts.gpio_144 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4)	/* uart2_rts.gpio_145 */
 		>;
 	};
 
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
@@ -62,7 +62,7 @@
 		>;
 	};
 
-	ads7846_pins: pinmux_ads7846_pins {
+	ads7846_pins: ads7846-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* csi2_dx1.gpio_114 */
 		>;
@@ -75,7 +75,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
@@ -160,7 +160,7 @@
 
 		interrupt-parent = <&gpio4>;
 		interrupts = <18 0>;			/* gpio_114 */
-		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <0x0>;
 		ti,x-max = /bits/ 16 <0x0fff>;
diff --git a/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-common-peripherals.dtsi
index 8a4a02472c9a..00369f699e20 100644
--- a/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-common-peripherals.dtsi
@@ -24,14 +24,14 @@
 };
 
 &omap3_pmx_core {
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl.i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda.i2c3_sda */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx */
diff --git a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-gallop43-common.dtsi
index 155aec121400..5f6721326f86 100644
--- a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-gallop43-common.dtsi
@@ -17,12 +17,12 @@
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
-		heartbeat {
+		led-heartbeat {
 			label = "overo:red:gpio21";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;		/* gpio_21 */
 			linux,default-trigger = "heartbeat";
 		};
-		gpio22 {
+		led-gpio22 {
 			label = "overo:blue:gpio22";
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;		/* gpio_22 */
 		};
diff --git a/arch/arm/boot/dts/omap3-overo-gallop43.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-gallop43.dts
index 24b40bdf7ea1..d882a58028c1 100644
--- a/arch/arm/boot/dts/omap3-overo-gallop43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-gallop43.dts
@@ -18,14 +18,14 @@
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-palo35-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-palo35-common.dtsi
index 82a04466747a..4b66f622ac13 100644
--- a/arch/arm/boot/dts/omap3-overo-palo35-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-palo35-common.dtsi
@@ -17,12 +17,12 @@
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
-		heartbeat {
+		led-heartbeat {
 			label = "overo:red:gpio21";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;		/* gpio_21 */
 			linux,default-trigger = "heartbeat";
 		};
-		gpio22 {
+		led-gpio22 {
 			label = "overo:blue:gpio22";
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;		/* gpio_22 */
 		};
diff --git a/arch/arm/boot/dts/omap3-overo-palo35.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-palo35.dts
index 55e08d56b18b..39c8e9ce5776 100644
--- a/arch/arm/boot/dts/omap3-overo-palo35.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-palo35.dts
@@ -18,14 +18,14 @@
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-palo43-common.dtsi
index 453a55324fa1..a8f163a899f0 100644
--- a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-palo43-common.dtsi
@@ -17,12 +17,12 @@
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
-		heartbeat {
+		led-heartbeat {
 			label = "overo:red:gpio21";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;		/* gpio_21 */
 			linux,default-trigger = "heartbeat";
 		};
-		gpio22 {
+		led-gpio22 {
 			label = "overo:blue:gpio22";
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;		/* gpio_22 */
 		};
diff --git a/arch/arm/boot/dts/omap3-overo-palo43.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-palo43.dts
index 092c8325a133..2c0f755ec8cc 100644
--- a/arch/arm/boot/dts/omap3-overo-palo43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-palo43.dts
@@ -18,14 +18,14 @@
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-storm-alto35.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-alto35.dts
index 7f04dfad8203..3eb935df04dc 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-alto35.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-alto35.dts
@@ -14,5 +14,5 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Alto35";
-	compatible = "gumstix,omap3-overo-alto35", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-alto35", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
diff --git a/arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-chestnut43.dts
index bc5a04e03336..25e82efe4f3b 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-chestnut43.dts
@@ -14,18 +14,18 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Chestnut43";
-	compatible = "gumstix,omap3-overo-chestnut43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-chestnut43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-storm-gallop43.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-gallop43.dts
index 065c31cbf0e2..0c93ea3f9774 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-gallop43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-gallop43.dts
@@ -14,18 +14,18 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Gallop43";
-	compatible = "gumstix,omap3-overo-gallop43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-gallop43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-storm-palo35.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-palo35.dts
index e38c1c51392c..9468ef9f9742 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-palo35.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-palo35.dts
@@ -14,18 +14,18 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Palo35";
-	compatible = "gumstix,omap3-overo-palo35", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-palo35", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-storm-palo43.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-palo43.dts
index e6dc23159c4d..9feead584479 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-palo43.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-palo43.dts
@@ -14,18 +14,18 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Palo43";
-	compatible = "gumstix,omap3-overo-palo43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-palo43", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 			OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)	/* etk_d8.gpio_22 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4)	/* etk_d9.gpio_23 */
 			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4)	/* etk_d0.gpio_14 */
diff --git a/arch/arm/boot/dts/omap3-overo-storm-summit.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-summit.dts
index 587c08ce282d..92f56b9d009d 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-summit.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-summit.dts
@@ -14,11 +14,11 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Summit";
-	compatible = "gumstix,omap3-overo-summit", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-summit", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-overo-storm-tobi.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-tobi.dts
index f57de6010994..6d14466c180a 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-tobi.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-tobi.dts
@@ -14,6 +14,6 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Tobi";
-	compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
 
diff --git a/arch/arm/boot/dts/omap3-overo-storm-tobiduo.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-tobiduo.dts
index 281af6c113be..bcf20ff3f281 100644
--- a/arch/arm/boot/dts/omap3-overo-storm-tobiduo.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm-tobiduo.dts
@@ -14,5 +14,5 @@
 
 / {
 	model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on TobiDuo";
-	compatible = "gumstix,omap3-overo-tobiduo", "gumstix,omap3-overo", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "gumstix,omap3-overo-tobiduo", "gumstix,omap3-overo", "ti,omap3630", "ti,omap3";
 };
diff --git a/arch/arm/boot/dts/omap3-overo-storm.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-storm.dtsi
index 2af15d5f61f9..da583b47ed8d 100644
--- a/arch/arm/boot/dts/omap3-overo-storm.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-storm.dtsi
@@ -12,7 +12,7 @@
 			&hsusb2_2_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -23,7 +23,7 @@
 		>;
 	};
 
-	w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
+	w3cbw003c_2_pins: w3cbw003c-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)		/* etk_d2.gpio_16 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-summit-common.dtsi
index df7450f17ffd..ec03ca17e98b 100644
--- a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-summit-common.dtsi
@@ -15,7 +15,7 @@
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
-		heartbeat {
+		led-heartbeat {
 			label = "overo:red:gpio21";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;		/* gpio_21 */
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/omap3-overo-summit.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-summit.dts
index a6c9799fe491..da5ca80430ae 100644
--- a/arch/arm/boot/dts/omap3-overo-summit.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-summit.dts
@@ -18,7 +18,7 @@
 };
 
 &omap3_pmx_core2 {
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)	/* etk_d7.gpio_21 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-tobi-common.dtsi
index 9bf4b88a4b50..5432e4e16ab5 100644
--- a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-tobi-common.dtsi
@@ -13,7 +13,7 @@
 / {
 	leds {
 		compatible = "gpio-leds";
-		heartbeat {
+		led-heartbeat {
 			label = "overo:red:gpio21";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/omap3-overo-tobi.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-tobi.dts
index ce3f2404f329..ce3f2404f329 100644
--- a/arch/arm/boot/dts/omap3-overo-tobi.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-tobi.dts
diff --git a/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo-tobiduo-common.dtsi
index e5da3bc6f105..218a10c0d815 100644
--- a/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-tobiduo-common.dtsi
@@ -22,7 +22,7 @@
 		compatible = "smsc,lan9221","smsc,lan9115";
 		bank-width = <2>;
 
-		gpmc,mux-add-data;
+		gpmc,mux-add-data = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <42>;
 		gpmc,cs-wr-off-ns = <36>;
diff --git a/arch/arm/boot/dts/omap3-overo-tobiduo.dts b/arch/arm/boot/dts/ti/omap/omap3-overo-tobiduo.dts
index fc6163eae45e..fc6163eae45e 100644
--- a/arch/arm/boot/dts/omap3-overo-tobiduo.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo-tobiduo.dts
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/ti/omap/omap3-overo.dtsi
index cc9263e99254..7dc044e87226 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-overo.dtsi
@@ -12,7 +12,7 @@
 			&hsusb2_2_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -23,7 +23,7 @@
 		>;
 	};
 
-	w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
+	w3cbw003c_2_pins: w3cbw003c-2-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)		/* etk_d2.gpio_16 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-pandora-1ghz.dts b/arch/arm/boot/dts/ti/omap/omap3-pandora-1ghz.dts
index ea509956d7ac..8d8c9085e6ff 100644
--- a/arch/arm/boot/dts/omap3-pandora-1ghz.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-pandora-1ghz.dts
@@ -16,7 +16,7 @@
 / {
 	model = "Pandora Handheld Console 1GHz";
 
-	compatible = "openpandora,omap3-pandora-1ghz", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "openpandora,omap3-pandora-1ghz", "ti,omap3630", "ti,omap3";
 };
 
 &omap3_pmx_core2 {
@@ -27,7 +27,7 @@
 		&control_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -38,7 +38,7 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
 			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_ctl.sdmmc3_cmd */
@@ -49,7 +49,7 @@
 		>;
 	};
 
-	control_pins: pinmux_control_pins {
+	control_pins: control-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* etk_d0.gpio_14 =  HP_SHUTDOWN */
 			OMAP3630_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4)		/* etk_d1.gpio_15 =  BT_SHUTDOWN */
diff --git a/arch/arm/boot/dts/omap3-pandora-600mhz.dts b/arch/arm/boot/dts/ti/omap/omap3-pandora-600mhz.dts
index 6bd9041942f2..2d5eac3ffc6c 100644
--- a/arch/arm/boot/dts/omap3-pandora-600mhz.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-pandora-600mhz.dts
@@ -27,7 +27,7 @@
 		&control_pins
 	>;
 
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+	hsusb2_2_pins: hsusb2-2-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -38,7 +38,7 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
 			OMAP3430_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_ctl.sdmmc3_cmd */
@@ -49,7 +49,7 @@
 		>;
 	};
 
-	control_pins: pinmux_control_pins {
+	control_pins: control-pins {
 		pinctrl-single,pins = <
 			OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* etk_d0.gpio_14 =  HP_SHUTDOWN */
 			OMAP3430_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4)		/* etk_d1.gpio_15 =  BT_SHUTDOWN */
diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/ti/omap/omap3-pandora-common.dtsi
index 150d5be42d27..06c5b2358999 100644
--- a/arch/arm/boot/dts/omap3-pandora-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-pandora-common.dtsi
@@ -205,7 +205,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */
 		vcc-supply = <&vaux2>;
@@ -251,7 +251,7 @@
 
 &omap3_pmx_core {
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
@@ -262,7 +262,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
@@ -277,7 +277,7 @@
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -311,14 +311,14 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
-	led_pins: pinmux_leds_pins {
+	led_pins: leds-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2154, PIN_OUTPUT | MUX_MODE4)	/* GPIO_128 */
 			OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4)	/* GPIO_129 */
@@ -327,7 +327,7 @@
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE4)	/* GPIO_96 */
 			OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE4)	/* GPIO_97 */
@@ -349,7 +349,7 @@
 		>;
 	};
 
-	penirq_pins: pinmux_penirq_pins {
+	penirq_pins: penirq-pins {
 		pinctrl-single,pins = <
 			/* here we could enable to wakeup the cpu from suspend by a pen touch */
 			OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE4)	/* GPIO_94 */
@@ -651,7 +651,7 @@
 		pinctrl-0 = <&penirq_pins>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <30 IRQ_TYPE_NONE>;	/* GPIO_94 */
-		pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio3 30 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&vaux4>;
 
 		ti,x-min = /bits/ 16 <0>;
@@ -666,7 +666,7 @@
 
 	lcd: lcd@1 {
 		reg = <1>;	/* CS1 */
-		compatible =	"tpo,td043mtea1";
+		compatible = "tpo,td043mtea1";
 		spi-max-frequency = <100000>;
 		spi-cpol;
 		spi-cpha;
@@ -702,7 +702,7 @@
 };
 
 &venc {
-	status = "ok";
+	status = "okay";
 
 	vdda-supply = <&vdac>;
 
@@ -718,7 +718,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = < &dss_dpi_pins >;
 
-	status = "ok";
+	status = "okay";
 	vdds_dsi-supply = <&vpll2>;
 
 	port {
diff --git a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi b/arch/arm/boot/dts/ti/omap/omap3-panel-sharp-ls037v7dw01.dtsi
index b8b9fcc41ef1..2dbb687d4df2 100644
--- a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-panel-sharp-ls037v7dw01.dtsi
@@ -46,7 +46,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 	port {
 		dpi_out: endpoint {
 			remote-endpoint = <&lcd_in>;
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/ti/omap/omap3-sb-t35.dtsi
index fb9842fa922c..6730c749d5ea 100644
--- a/arch/arm/boot/dts/omap3-sb-t35.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-sb-t35.dtsi
@@ -56,27 +56,27 @@
 };
 
 &omap3_pmx_core {
-	smsc2_pins: pinmux_smsc2_pins {
+	smsc2_pins: smsc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs4.gpmc_ncs4 */
 			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
 		>;
 	};
 
-	tfp410_pins: pinmux_tfp410_pins {
+	tfp410_pins: tfp410-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs3.gpio_54 */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
 		>;
 	};
 
-	sb_t35_audio_amp: pinmux_sb_t35_audio_amp {
+	sb_t35_audio_amp: sb-t35-audio-amp-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4) /* gpmc_nbe1.gpio_61 */
 		>;
@@ -108,8 +108,8 @@
 		reg = <4 0 0xff>;
 		bank-width = <2>;
 		gpmc,device-width = <1>;
-		gpmc,cycle2cycle-samecsen = <1>;
-		gpmc,cycle2cycle-diffcsen = <1>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
 		gpmc,cs-on-ns = <5>;
 		gpmc,cs-rd-off-ns = <150>;
 		gpmc,cs-wr-off-ns = <150>;
diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/ti/omap/omap3-sbc-t3517.dts
index a69d32860421..07bec48dc441 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3517.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-sbc-t3517.dts
@@ -36,14 +36,14 @@
 			&usb_hub_pins
 		    >;
 
-	mmc1_aux_pins: pinmux_mmc1_aux_pins {
+	mmc1_aux_pins: mmc1-aux-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20c0, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_clk.gpio_59   */
 			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_cts.gpio_144 */
 		>;
 	};
 
-	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+	sb_t35_usb_hub_pins: sb-t35-usb-hub-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ec, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_98 - SB-T35 USB HUB RST */
 		>;
diff --git a/arch/arm/boot/dts/omap3-sbc-t3530.dts b/arch/arm/boot/dts/ti/omap/omap3-sbc-t3530.dts
index 24bf3fd86641..1beefc319422 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3530.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-sbc-t3530.dts
@@ -20,7 +20,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sb_t35_usb_hub_pins>;
 
-	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+	sb_t35_usb_hub_pins: sb-t35-usb-hub-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
 		>;
diff --git a/arch/arm/boot/dts/omap3-sbc-t3730.dts b/arch/arm/boot/dts/ti/omap/omap3-sbc-t3730.dts
index eb3893b9535e..aefc1187ebc9 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3730.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-sbc-t3730.dts
@@ -8,7 +8,7 @@
 
 / {
 	model = "CompuLab SBC-T3730 with CM-T3730";
-	compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap3630", "ti,omap3";
 
 	aliases {
 		display0 = &dvi0;
@@ -20,7 +20,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sb_t35_usb_hub_pins>;
 
-	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+	sb_t35_usb_hub_pins: sb-t35-usb-hub-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
 		>;
diff --git a/arch/arm/boot/dts/omap3-sniper.dts b/arch/arm/boot/dts/ti/omap/omap3-sniper.dts
index b6879cdc5c13..79e004057482 100644
--- a/arch/arm/boot/dts/omap3-sniper.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-sniper.dts
@@ -9,7 +9,7 @@
 
 / {
 	model = "LG Optimus Black";
-	compatible = "lg,omap3-sniper", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "lg,omap3-sniper", "ti,omap3630", "ti,omap3";
 
 	cpus {
 		cpu@0 {
@@ -26,48 +26,48 @@
 &omap3_pmx_core {
 	pinctrl-names = "default";
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)	/* uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx */
 		>;
 	};
 
-	dp3t_sel_pins: pinmux_dp3t_sel_pins {
+	dp3t_sel_pins: dp3t-sel-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE4)	/* gpio_161 */
 			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* gpio_162 */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)	/* i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)	/* i2c2_scl */
 			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	lp8720_en_pin: pinmux_lp8720_en_pin {
+	lp8720_en_pin: lp8720-en-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2080, PIN_OUTPUT | MUX_MODE4)	/* gpio_37 */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT | MUX_MODE0)	/* sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd */
@@ -78,7 +78,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT | MUX_MODE0)	/* sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT | MUX_MODE0)	/* sdmmc2_cmd */
@@ -93,7 +93,7 @@
 		>;
 	};
 
-	usb_otg_hs_pins: pinmux_usb_otg_hs_pins {
+	usb_otg_hs_pins: usb-otg-hs-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)	/* hsusb0_clk */
 			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp */
@@ -114,7 +114,7 @@
 &omap3_pmx_wkup {
 	pinctrl-names = "default";
 
-	mmc1_cd_pin: pinmux_mmc1_cd_pin {
+	mmc1_cd_pin: mmc1-cd-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a1a, PIN_INPUT | MUX_MODE4)		/* gpio_10 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-tao3530.dtsi b/arch/arm/boot/dts/ti/omap/omap3-tao3530.dtsi
index f24e2326cfa7..92a5846048bd 100644
--- a/arch/arm/boot/dts/omap3-tao3530.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3-tao3530.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  * Copyright (C) 2014 Stefan Roese <sr@denx.de>
  */
 /dts-v1/;
@@ -8,7 +8,11 @@
 #include "omap34xx.dtsi"
 
 /* Secure omaps have some devices inaccessible depending on the firmware */
-&aes {
+&aes1_target {
+	status = "disabled";
+};
+
+&aes2_target {
 	status = "disabled";
 };
 
@@ -39,7 +43,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;	/* gpio_162 */
 		vcc-supply = <&hsusb2_power>;
@@ -66,7 +70,7 @@
 };
 
 &omap3_pmx_core {
-	hsusbb2_pins: pinmux_hsusbb2_pins {
+	hsusbb2_pins: hsusbb2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
 			OMAP3_CORE1_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
@@ -83,7 +87,7 @@
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -98,7 +102,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
@@ -110,27 +114,27 @@
 	};
 
 	/* wlan GPIO output for WLAN_EN */
-	wlan_gpio: pinmux_wlan_gpio {
+	wlan_gpio: wlan-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_fsr gpio_157 */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
 			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl.i2c3_scl */
 			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda.i2c3_sda */
 		>;
 	};
 
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)	/* mcspi1_clk.mcspi1_clk */
 			OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)	/* mcspi1_simo.mcspi1_simo */
@@ -139,7 +143,7 @@
 		>;
 	};
 
-	mcspi3_pins: pinmux_mcspi3_pins {
+	mcspi3_pins: mcspi3-pins {
 		pinctrl-single,pins = <
                         OMAP3_CORE1_IOPAD(0x25dc, PIN_OUTPUT | MUX_MODE1)	/* etk_d0.mcspi3_simo gpio14 INPUT | MODE1 */
                         OMAP3_CORE1_IOPAD(0x25de, PIN_INPUT_PULLUP | MUX_MODE1)	/* etk_d1.mcspi3_somi gpio15 INPUT | MODE1 */
@@ -148,7 +152,7 @@
 		>;
 	};
 
-	mcbsp3_pins: pinmux_mcbsp3_pins {
+	mcbsp3_pins: mcbsp3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216c, PIN_OUTPUT | MUX_MODE0)	/* mcbsp3_dx.uart2_cts */
 			OMAP3_CORE1_IOPAD(0x216e, PIN_INPUT | MUX_MODE0)	/* mcbsp3_dr.uart2_rts */
@@ -193,25 +197,11 @@
 &mcspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcspi1_pins>;
-
-	spidev@0 {
-		compatible = "spidev";
-		spi-max-frequency = <48000000>;
-		reg = <0>;
-		spi-cpha;
-	};
 };
 
 &mcspi3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcspi3_pins>;
-
-	spidev@0 {
-		compatible = "spidev";
-		spi-max-frequency = <48000000>;
-		reg = <0>;
-		spi-cpha;
-	};
 };
 
 #include "twl4030.dtsi"
diff --git a/arch/arm/boot/dts/omap3-thunder.dts b/arch/arm/boot/dts/ti/omap/omap3-thunder.dts
index 64221e3b3477..c87956c59b08 100644
--- a/arch/arm/boot/dts/omap3-thunder.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-thunder.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  * Copyright (C) 2014 Stefan Roese <sr@denx.de>
  */
 
@@ -12,7 +12,7 @@
 };
 
 &omap3_pmx_core {
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)	/* dss_pclk.dss_pclk */
 			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)	/* dss_hsync.dss_hsync */
@@ -45,13 +45,13 @@
 		>;
 	};
 
-	lte430_pins: pinmux_lte430_pins {
+	lte430_pins: lte430-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat6.gpio_138 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat7.gpio_139 */
 		>;
@@ -64,7 +64,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/ti/omap/omap3-zoom3.dts
index d240e39f2151..9f1e125fd77b 100644
--- a/arch/arm/boot/dts/omap3-zoom3.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3-zoom3.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -9,7 +9,7 @@
 
 / {
 	model = "TI Zoom3";
-	compatible = "ti,omap3-zoom3", "ti,omap3630", "ti,omap36xx", "ti,omap3";
+	compatible = "ti,omap3-zoom3", "ti,omap3630", "ti,omap3";
 
 	cpus {
 		cpu@0 {
@@ -23,9 +23,9 @@
 	};
 
 	vddvario: regulator-vddvario {
-		  compatible = "regulator-fixed";
-		  regulator-name = "vddvario";
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
 	};
 
 	vdd33a: regulator-vdd33a {
@@ -49,7 +49,7 @@
 
 &omap3_pmx_core {
 	/* REVISIT: twl gpio0 is mmc0_cd */
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP3_CORE1_IOPAD(0x2146, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -60,7 +60,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
@@ -75,42 +75,42 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2198, PIN_INPUT | MUX_MODE4)	/* mcbsp1_clkx.gpio_162 WLAN IRQ */
 			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs1.sdmmc3_cmd */
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
-                        OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0)		/* uart1_cts.uart1_cts */
-                        OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0)		/* uart1_rts.uart1_rts */
-                        OMAP3_CORE1_IOPAD(0x2182, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
-                        OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)		/* uart1_tx.uart1_tx */
+			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0)		/* uart1_cts.uart1_cts */
+			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0)		/* uart1_rts.uart1_rts */
+			OMAP3_CORE1_IOPAD(0x2182, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
+			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)		/* uart1_tx.uart1_tx */
 		>;
 	};
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
-                        OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
-                        OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
-                        OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
-                        OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
+			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
+			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
-                        OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
-                        OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
-                        OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
-                        OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
+			OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
+			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
 	/* wl12xx GPIO output for WLAN_EN */
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x211a, PIN_OUTPUT| MUX_MODE4)		/* cam_d2.gpio_101 */
 		>;
@@ -118,7 +118,7 @@
 };
 
 &omap3_pmx_core2 {
-	mmc3_2_pins: pinmux_mmc3_2_pins {
+	mmc3_2_pins: mmc3-2-pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
 			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
@@ -130,7 +130,7 @@
 };
 
 &omap3_pmx_wkup {
-	wlan_host_wkup: pinmux_wlan_host_wkup_pins {
+	wlan_host_wkup: wlan-host-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a1a, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_clkout1.gpio_10 WLAN_HOST_WKUP */
 		>;
@@ -205,22 +205,22 @@
 };
 
 &uart1 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
 };
 
 &uart2 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
 };
 
 &uart3 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart3_pins>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
 };
 
 &uart4 {
-       status = "disabled";
+	status = "disabled";
 };
 
 &usb_otg_hs {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/ti/omap/omap3.dtsi
index 5698a3e241aa..92cd4c99dae7 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC
  *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
@@ -24,6 +21,9 @@
 		i2c0 = &i2c1;
 		i2c1 = &i2c2;
 		i2c2 = &i2c3;
+		mmc0 = &mmc1;
+		mmc1 = &mmc2;
+		mmc2 = &mmc3;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -157,13 +157,56 @@
 			};
 		};
 
-		aes: aes@480c5000 {
-			compatible = "ti,omap3-aes";
-			ti,hwmods = "aes";
-			reg = <0x480c5000 0x50>;
-			interrupts = <0>;
-			dmas = <&sdma 65 &sdma 66>;
-			dma-names = "tx", "rx";
+		aes1_target: target-module@480a6000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x480a6044 0x4>,
+			      <0x480a6048 0x4>,
+			      <0x480a604c 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&aes1_ick>;
+			clock-names = "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x480a6000 0x2000>;
+
+			aes1: aes1@0 {
+				compatible = "ti,omap3-aes";
+				reg = <0 0x50>;
+				interrupts = <0>;
+				dmas = <&sdma 9 &sdma 10>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		aes2_target: target-module@480c5000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x480c5044 0x4>,
+			      <0x480c5048 0x4>,
+			      <0x480c504c 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&aes2_ick>;
+			clock-names = "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x480c5000 0x2000>;
+
+			aes2: aes2@0 {
+				compatible = "ti,omap3-aes";
+				reg = <0 0x50>;
+				interrupts = <0>;
+				dmas = <&sdma 65 &sdma 66>;
+				dma-names = "tx", "rx";
+			};
 		};
 
 		prm: prm@48306000 {
@@ -193,10 +236,23 @@
 			};
 		};
 
-		counter32k: counter@48320000 {
-			compatible = "ti,omap-counter32k";
-			reg = <0x48320000 0x20>;
-			ti,hwmods = "counter_32k";
+		target-module@48320000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x48320000 0x4>,
+			      <0x48320004 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>;
+			clocks = <&wkup_32k_fck>, <&omap_32ksync_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x48320000 0x1000>;
+
+			counter32k: counter@0 {
+				compatible = "ti,omap-counter32k";
+				reg = <0x0 0x20>;
+			};
 		};
 
 		intc: interrupt-controller@48200000 {
@@ -206,17 +262,41 @@
 			reg = <0x48200000 0x1000>;
 		};
 
-		sdma: dma-controller@48056000 {
-			compatible = "ti,omap3630-sdma", "ti,omap3430-sdma";
-			reg = <0x48056000 0x1000>;
-			interrupts = <12>,
-				     <13>,
-				     <14>,
-				     <15>;
-			#dma-cells = <1>;
-			dma-channels = <32>;
-			dma-requests = <96>;
-			ti,hwmods = "dma";
+		target-module@48056000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x48056000 0x4>,
+			      <0x4805602c 0x4>,
+			      <0x48056028 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (V, P, C): core, core_pwrdm, core_l3_clkdm */
+			clocks = <&core_l3_ick>;
+			clock-names = "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48056000 0x1000>;
+
+			sdma: dma-controller@0 {
+				compatible = "ti,omap3430-sdma", "ti,omap-sdma";
+				reg = <0x0 0x1000>;
+				interrupts = <12>,
+					     <13>,
+					     <14>,
+					     <15>;
+				#dma-cells = <1>;
+				dma-channels = <32>;
+				dma-requests = <96>;
+			};
 		};
 
 		gpio1: gpio@48310000 {
@@ -320,8 +400,6 @@
 			compatible = "ti,omap3-i2c";
 			reg = <0x48070000 0x80>;
 			interrupts = <56>;
-			dmas = <&sdma 27 &sdma 28>;
-			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c1";
@@ -331,8 +409,6 @@
 			compatible = "ti,omap3-i2c";
 			reg = <0x48072000 0x80>;
 			interrupts = <57>;
-			dmas = <&sdma 29 &sdma 30>;
-			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c2";
@@ -342,8 +418,6 @@
 			compatible = "ti,omap3-i2c";
 			reg = <0x48060000 0x80>;
 			interrupts = <61>;
-			dmas = <&sdma 25 &sdma 26>;
-			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
@@ -357,7 +431,7 @@
 			#mbox-cells = <1>;
 			ti,mbox-num-users = <2>;
 			ti,mbox-num-fifos = <2>;
-			mbox_dsp: dsp {
+			mbox_dsp: mbox-dsp {
 				ti,mbox-tx = <0 0 0>;
 				ti,mbox-rx = <1 0 0>;
 			};
@@ -613,19 +687,63 @@
 			dma-names = "rx";
 		};
 
-		timer1: timer@48318000 {
-			compatible = "ti,omap3430-timer";
-			reg = <0x48318000 0x400>;
-			interrupts = <37>;
-			ti,hwmods = "timer1";
-			ti,timer-alwon;
+		timer1_target: target-module@48318000 {
+			compatible = "ti,sysc-omap2-timer", "ti,sysc";
+			reg = <0x48318000 0x4>,
+			      <0x48318010 0x4>,
+			      <0x48318014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&gpt1_fck>, <&gpt1_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x48318000 0x1000>;
+
+			timer1: timer@0 {
+				compatible = "ti,omap3430-timer";
+				reg = <0x0 0x80>;
+				clocks = <&gpt1_fck>;
+				clock-names = "fck";
+				interrupts = <37>;
+				ti,timer-alwon;
+			};
 		};
 
-		timer2: timer@49032000 {
-			compatible = "ti,omap3430-timer";
-			reg = <0x49032000 0x400>;
-			interrupts = <38>;
-			ti,hwmods = "timer2";
+		timer2_target: target-module@49032000 {
+			compatible = "ti,sysc-omap2-timer", "ti,sysc";
+			reg = <0x49032000 0x4>,
+			      <0x49032010 0x4>,
+			      <0x49032014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&gpt2_fck>, <&gpt2_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x49032000 0x1000>;
+
+			timer2: timer@0 {
+				compatible = "ti,omap3430-timer";
+				reg = <0 0x400>;
+				interrupts = <38>;
+			};
 		};
 
 		timer3: timer@49034000 {
@@ -699,13 +817,34 @@
 			ti,timer-pwm;
 		};
 
-		timer12: timer@48304000 {
-			compatible = "ti,omap3430-timer";
-			reg = <0x48304000 0x400>;
-			interrupts = <95>;
-			ti,hwmods = "timer12";
-			ti,timer-alwon;
-			ti,timer-secure;
+		timer12_target: target-module@48304000 {
+			compatible = "ti,sysc-omap2-timer", "ti,sysc";
+			reg = <0x48304000 0x4>,
+			      <0x48304010 0x4>,
+			      <0x48304014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_EMUFREE |
+					 SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			clocks = <&gpt12_fck>, <&gpt12_ick>;
+			clock-names = "fck", "ick";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x48304000 0x1000>;
+
+			timer12: timer@0 {
+				compatible = "ti,omap3430-timer";
+				reg = <0 0x400>;
+				interrupts = <95>;
+				ti,timer-alwon;
+				ti,timer-secure;
+			};
 		};
 
 		usbhstll: usbhstll@48062000 {
@@ -754,15 +893,37 @@
 			#gpio-cells = <2>;
 		};
 
-		usb_otg_hs: usb_otg_hs@480ab000 {
-			compatible = "ti,omap3-musb";
-			reg = <0x480ab000 0x1000>;
-			interrupts = <92>, <93>;
-			interrupt-names = "mc", "dma";
-			ti,hwmods = "usb_otg_hs";
-			multipoint = <1>;
-			num-eps = <16>;
-			ram-bits = <12>;
+		usb_otg_target: target-module@480ab000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x480ab400 0x4>,
+			      <0x480ab404 0x4>,
+			      <0x480ab408 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Clock defined in the SoC specific dtsi file */
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x480ab000 0x1000>;
+
+			usb_otg_hs: usb@0 {
+				compatible = "ti,omap3-musb";
+				reg = <0 0x1000>;
+				interrupts = <92>, <93>;
+				interrupt-names = "mc", "dma";
+				multipoint = <1>;
+				num-eps = <16>;
+				ram-bits = <12>;
+			};
 		};
 
 		dss: dss@48050000 {
@@ -796,6 +957,9 @@
 				ti,hwmods = "dss_dsi1";
 				clocks = <&dss1_alwon_fck>, <&dss2_alwon_fck>;
 				clock-names = "fck", "sys_clk";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
 			};
 
 			rfbi: encoder@48050800 {
@@ -862,4 +1026,14 @@
 	};
 };
 
-/include/ "omap3xxx-clocks.dtsi"
+#include "omap3xxx-clocks.dtsi"
+
+/* Preferred always-on timer for clockevent. Some boards must use dmtimer12 */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt1_fck>;
+		assigned-clock-parents = <&omap_32k_fck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/ti/omap/omap3430-sdp.dts
index 7bfde8aac7ae..258ecd9e4519 100644
--- a/arch/arm/boot/dts/omap3430-sdp.dts
+++ b/arch/arm/boot/dts/ti/omap/omap3430-sdp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -53,7 +53,7 @@
 
 	nor@0,0 {
 		compatible = "cfi-flash";
-		linux,mtd-name= "intel,pf48f6000m0y1be";
+		linux,mtd-name = "intel,pf48f6000m0y1be";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0 0 0x08000000>;
@@ -101,11 +101,11 @@
 
 	nand@1,0 {
 		compatible = "ti,omap2-nand";
-		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		reg = <1 0 4>; /* CS1, offset 0, IO size 4 */
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,mt29f1g08abb";
+		linux,mtd-name = "micron,mt29f1g08abb";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "sw";
@@ -148,7 +148,7 @@
 	};
 
 	onenand@2,0 {
-		linux,mtd-name= "samsung,kfm2g16q2m-deb8";
+		linux,mtd-name = "samsung,kfm2g16q2m-deb8";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "ti,omap2-onenand";
diff --git a/arch/arm/boot/dts/omap3430es1-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap3430es1-clocks.dtsi
index 2ec3628d3315..24adfac26be0 100644
--- a/arch/arm/boot/dts/omap3430es1-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap3430es1-clocks.dtsi
@@ -46,37 +46,61 @@
 		ti,bit-shift = <2>;
 	};
 
-	d2d_26m_fck: d2d_26m_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <3>;
-	};
-
-	fshostusb_fck: fshostusb_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <5>;
-	};
-
-	ssi_ssr_gate_fck_3430es1: ssi_ssr_gate_fck_3430es1@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <0>;
-		reg = <0x0a00>;
-	};
-
-	ssi_ssr_div_fck_3430es1: ssi_ssr_div_fck_3430es1@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-divider-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <8>;
-		reg = <0x0a40>;
-		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		d2d_26m_fck: clock-d2d-26m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "d2d_26m_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <3>;
+		};
+
+		fshostusb_fck: clock-fshostusb-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "fshostusb_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <5>;
+		};
+
+		ssi_ssr_gate_fck_3430es1: clock-ssi-ssr-gate-fck-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-no-wait-gate-clock";
+			clock-output-names = "ssi_ssr_gate_fck_3430es1";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <0>;
+		};
+	};
+
+	clock@a40 {
+		compatible = "ti,clksel";
+		reg = <0xa40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ssi_ssr_div_fck_3430es1: clock-ssi-ssr-div-fck-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-divider-clock";
+			clock-output-names = "ssi_ssr_div_fck_3430es1";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <8>;
+			ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+		};
+
+		usb_l4_div_ick: clock-usb-l4-div-ick {
+			#clock-cells = <0>;
+			compatible = "ti,composite-divider-clock";
+			clock-output-names = "usb_l4_div_ick";
+			clocks = <&l4_ick>;
+			ti,bit-shift = <4>;
+			ti,max-div = <1>;
+			ti,index-starts-at-one;
+		};
 	};
 
 	ssi_ssr_fck: ssi_ssr_fck_3430es1 {
@@ -93,20 +117,43 @@
 		clock-div = <2>;
 	};
 
-	hsotgusb_ick_3430es1: hsotgusb_ick_3430es1@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <4>;
-	};
-
-	fac_ick: fac_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <8>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		hsotgusb_ick_3430es1: clock-hsotgusb-ick-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-no-wait-interface-clock";
+			clock-output-names = "hsotgusb_ick_3430es1";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		fac_ick: clock-fac-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "fac_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <8>;
+		};
+
+		ssi_ick: clock-ssi-ick-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-no-wait-interface-clock";
+			clock-output-names = "ssi_ick_3430es1";
+			clocks = <&ssi_l4_ick>;
+			ti,bit-shift = <0>;
+		};
+
+		usb_l4_gate_ick: clock-usb-l4-gate-ick {
+			#clock-cells = <0>;
+			compatible = "ti,composite-interface-clock";
+			clock-output-names = "usb_l4_gate_ick";
+			clocks = <&l4_ick>;
+			ti,bit-shift = <5>;
+		};
 	};
 
 	ssi_l4_ick: ssi_l4_ick {
@@ -117,45 +164,26 @@
 		clock-div = <1>;
 	};
 
-	ssi_ick: ssi_ick_3430es1@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&ssi_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <0>;
-	};
-
-	usb_l4_gate_ick: usb_l4_gate_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-interface-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <5>;
-		reg = <0x0a10>;
-	};
-
-	usb_l4_div_ick: usb_l4_div_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-divider-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <4>;
-		ti,max-div = <1>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
 	usb_l4_ick: usb_l4_ick {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&usb_l4_gate_ick>, <&usb_l4_div_ick>;
 	};
 
-	dss1_alwon_fck: dss1_alwon_fck_3430es1@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m4x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0e00>;
-		ti,set-rate-parent;
+	clock@e00 {
+		compatible = "ti,clksel";
+		reg = <0xe00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dss1_alwon_fck: clock-dss1-alwon-fck-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss1_alwon_fck_3430es1";
+			clocks = <&dpll4_m4x2_ck>;
+			ti,bit-shift = <0>;
+			ti,set-rate-parent;
+		};
 	};
 
 	dss_ick: dss_ick_3430es1@e10 {
diff --git a/arch/arm/boot/dts/ti/omap/omap34xx-omap36xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap34xx-omap36xx-clocks.dtsi
new file mode 100644
index 000000000000..8374532f20e2
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap34xx-omap36xx-clocks.dtsi
@@ -0,0 +1,310 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree Source for OMAP34XX/OMAP36XX clock data
+ *
+ * Copyright (C) 2013 Texas Instruments, Inc.
+ */
+&cm_clocks {
+	security_l4_ick2: security_l4_ick2 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l4_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	clock@a14 {
+		compatible = "ti,clksel";
+		reg = <0xa14>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		aes1_ick: clock-aes1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "aes1_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <3>;
+		};
+
+		rng_ick: clock-rng-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "rng_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <2>;
+		};
+
+		sha11_ick: clock-sha11-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "sha11_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <1>;
+		};
+
+		des1_ick: clock-des1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "des1_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <0>;
+		};
+
+		pka_ick: clock-pka-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "pka_ick";
+			clocks = <&security_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+	};
+
+	/* CM_FCLKEN_CAM */
+	clock@f00 {
+		compatible = "ti,clksel";
+		reg = <0xf00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		cam_mclk: clock-cam-mclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "cam_mclk";
+			clocks = <&dpll4_m5x2_ck>;
+			ti,bit-shift = <0>;
+			ti,set-rate-parent;
+		};
+
+		csi2_96m_fck: clock-csi2-96m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "csi2_96m_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <1>;
+		};
+	};
+
+	cam_ick: cam_ick@f10 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-no-wait-interface-clock";
+		clocks = <&l4_ick>;
+		reg = <0x0f10>;
+		ti,bit-shift = <0>;
+	};
+
+	security_l3_ick: security_l3_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l3_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		icr_ick: clock-icr-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "icr_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <29>;
+		};
+
+		des2_ick: clock-des2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "des2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <26>;
+		};
+
+		mspro_ick: clock-mspro-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mspro_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <23>;
+		};
+
+		mailboxes_ick: clock-mailboxes-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mailboxes_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <7>;
+		};
+
+		sad2d_ick: clock-sad2d-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "sad2d_ick";
+			clocks = <&l3_ick>;
+			ti,bit-shift = <3>;
+		};
+	};
+
+	ssi_l4_ick: ssi_l4_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l4_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	clock@c00 {
+		compatible = "ti,clksel";
+		reg = <0xc00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		sr1_fck: clock-sr1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "sr1_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		sr2_fck: clock-sr2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "sr2_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
+	};
+
+	sr_l4_ick: sr_l4_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l4_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dpll2_fck: dpll2_fck@40 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&core_ck>;
+		ti,bit-shift = <19>;
+		ti,max-div = <7>;
+		reg = <0x0040>;
+		ti,index-starts-at-one;
+	};
+
+	dpll2_ck: dpll2_ck@4 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-dpll-clock";
+		clocks = <&sys_ck>, <&dpll2_fck>;
+		reg = <0x0004>, <0x0024>, <0x0040>, <0x0034>;
+		ti,low-power-stop;
+		ti,lock;
+		ti,low-power-bypass;
+	};
+
+	dpll2_m2_ck: dpll2_m2_ck@44 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll2_ck>;
+		ti,max-div = <31>;
+		reg = <0x0044>;
+		ti,index-starts-at-one;
+	};
+
+	iva2_ck: iva2_ck@0 {
+		#clock-cells = <0>;
+		compatible = "ti,wait-gate-clock";
+		clocks = <&dpll2_m2_ck>;
+		reg = <0x0000>;
+		ti,bit-shift = <0>;
+	};
+
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		modem_fck: clock-modem-fck {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "modem_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <31>;
+		};
+
+		mspro_fck: clock-mspro-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mspro_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <23>;
+		};
+	};
+
+	/* CM_ICLKEN3_CORE */
+	clock@a18 {
+		compatible = "ti,clksel";
+		reg = <0xa18>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mad2d_ick: clock-mad2d-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mad2d_ick";
+			clocks = <&l3_ick>;
+			ti,bit-shift = <3>;
+		};
+	};
+
+};
+
+&cm_clockdomains {
+	cam_clkdm: cam_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&cam_ick>, <&csi2_96m_fck>;
+	};
+
+	iva2_clkdm: iva2_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&iva2_ck>;
+	};
+
+	dpll2_clkdm: dpll2_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&dpll2_ck>;
+	};
+
+	wkup_clkdm: wkup_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>,
+			 <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>,
+			 <&gpt1_ick>, <&sr1_fck>, <&sr2_fck>;
+	};
+
+	d2d_clkdm: d2d_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&modem_fck>, <&sad2d_ick>, <&mad2d_ick>;
+	};
+
+	core_l4_clkdm: core_l4_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>,
+			 <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>,
+			 <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>,
+			 <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>,
+			 <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>,
+			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
+			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
+			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
+			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>,
+			 <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,
+			 <&rng_ick>, <&mspro_fck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/ti/omap/omap34xx.dtsi
index c4dd9801840d..fc7233ac183a 100644
--- a/arch/arm/boot/dts/omap34xx.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap34xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP34xx/OMAP35xx SoC
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
@@ -20,15 +17,15 @@
 			operating-points-v2 = <&cpu0_opp_table>;
 
 			clock-latency = <300000>; /* From legacy driver */
+			#cooling-cells = <2>;
 		};
 	};
 
-	/* see Documentation/devicetree/bindings/opp/opp.txt */
 	cpu0_opp_table: opp-table {
 		compatible = "operating-points-v2-ti-cpu";
 		syscon = <&scm_conf>;
 
-		opp1-125000000 {
+		opp-125000000 {
 			opp-hz = /bits/ 64 <125000000>;
 			/*
 			 * we currently only select the max voltage from table
@@ -43,32 +40,32 @@
 			opp-supported-hw = <0xffffffff 3>;
 		};
 
-		opp2-250000000 {
+		opp-250000000 {
 			opp-hz = /bits/ 64 <250000000>;
 			opp-microvolt = <1075000 1075000 1075000>;
 			opp-supported-hw = <0xffffffff 3>;
 			opp-suspend;
 		};
 
-		opp3-500000000 {
+		opp-500000000 {
 			opp-hz = /bits/ 64 <500000000>;
 			opp-microvolt = <1200000 1200000 1200000>;
 			opp-supported-hw = <0xffffffff 3>;
 		};
 
-		opp4-550000000 {
+		opp-550000000 {
 			opp-hz = /bits/ 64 <550000000>;
 			opp-microvolt = <1275000 1275000 1275000>;
 			opp-supported-hw = <0xffffffff 3>;
 		};
 
-		opp5-600000000 {
+		opp-600000000 {
 			opp-hz = /bits/ 64 <600000000>;
 			opp-microvolt = <1350000 1350000 1350000>;
 			opp-supported-hw = <0xffffffff 3>;
 		};
 
-		opp6-720000000 {
+		opp-720000000 {
 			opp-hz = /bits/ 64 <720000000>;
 			opp-microvolt = <1350000 1350000 1350000>;
 			/* only high-speed grade omap3530 devices */
@@ -182,7 +179,7 @@
 };
 
 &ssi {
-	status = "ok";
+	status = "okay";
 
 	clocks = <&ssi_ssr_fck>,
 		 <&ssi_sst_fck>,
@@ -192,6 +189,10 @@
 		      "ssi_ick";
 };
 
+&usb_otg_target {
+	clocks = <&hsotgusb_ick_3430es2>;
+};
+
 /include/ "omap34xx-omap36xx-clocks.dtsi"
 /include/ "omap36xx-omap3430es2plus-clocks.dtsi"
 /include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
diff --git a/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
index 9974d5226971..dcc5cfcd1fe6 100644
--- a/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
@@ -133,37 +133,66 @@
 		ti,bit-shift = <2>;
 	};
 
-	usbtll_ick: usbtll_ick@a18 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a18>;
-		ti,bit-shift = <2>;
+	/* CM_ICLKEN3_CORE */
+	clock@a18 {
+		compatible = "ti,clksel";
+		reg = <0xa18>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		usbtll_ick: clock-usbtll-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "usbtll_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <2>;
+		};
 	};
 
-	mmchs3_ick: mmchs3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <30>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mmchs3_ick: clock-mmchs3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mmchs3_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <30>;
+		};
 	};
 
-	mmchs3_fck: mmchs3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <30>;
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mmchs3_fck: clock-mmchs3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mmchs3_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <30>;
+		};
 	};
 
-	dss1_alwon_fck: dss1_alwon_fck_3430es2@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,dss-gate-clock";
-		clocks = <&dpll4_m4x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0e00>;
-		ti,set-rate-parent;
+	clock@e00 {
+		compatible = "ti,clksel";
+		reg = <0xe00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dss1_alwon_fck: clock-dss1-alwon-fck-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,dss-gate-clock";
+			clock-output-names = "dss1_alwon_fck_3430es2";
+			clocks = <&dpll4_m4x2_ck>;
+			ti,bit-shift = <0>;
+			ti,set-rate-parent;
+		};
 	};
 
 	dss_ick: dss_ick_3430es2@e10 {
diff --git a/arch/arm/boot/dts/omap36xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap36xx-clocks.dtsi
index 4e9cc9003594..c5fdb2bd765d 100644
--- a/arch/arm/boot/dts/omap36xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap36xx-clocks.dtsi
@@ -58,12 +58,19 @@
 		ti,set-bit-to-disable;
 	};
 
-	uart4_fck: uart4_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_48m_fck>;
+	clock@1000 {
+		compatible = "ti,clksel";
 		reg = <0x1000>;
-		ti,bit-shift = <18>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		uart4_fck: clock-uart4-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart4_fck";
+			clocks = <&per_48m_fck>;
+			ti,bit-shift = <18>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap36xx-omap3430es2plus-clocks.dtsi
index 945537aee3ca..c94eb86d3da7 100644
--- a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap36xx-omap3430es2plus-clocks.dtsi
@@ -5,21 +5,35 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &cm_clocks {
-	ssi_ssr_gate_fck_3430es2: ssi_ssr_gate_fck_3430es2@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <0>;
-		reg = <0x0a00>;
-	};
-
-	ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-divider-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <8>;
-		reg = <0x0a40>;
-		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ssi_ssr_gate_fck_3430es2: clock-ssi-ssr-gate-fck-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-no-wait-gate-clock";
+			clock-output-names = "ssi_ssr_gate_fck_3430es2";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <0>;
+		};
+	};
+
+	clock@a40 {
+		compatible = "ti,clksel";
+		reg = <0xa40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ssi_ssr_div_fck_3430es2: clock-ssi-ssr-div-fck-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-divider-clock";
+			clock-output-names = "ssi_ssr_div_fck_3430es2";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <8>;
+			ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+		};
 	};
 
 	ssi_ssr_fck: ssi_ssr_fck_3430es2 {
@@ -36,12 +50,27 @@
 		clock-div = <2>;
 	};
 
-	hsotgusb_ick_3430es2: hsotgusb_ick_3430es2@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-hsotgusb-interface-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <4>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		hsotgusb_ick_3430es2: clock-hsotgusb-ick-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-hsotgusb-interface-clock";
+			clock-output-names = "hsotgusb_ick_3430es2";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		ssi_ick: clock-ssi-ick-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-ssi-interface-clock";
+			clock-output-names = "ssi_ick_3430es2";
+			clocks = <&ssi_l4_ick>;
+			ti,bit-shift = <0>;
+		};
 	};
 
 	ssi_l4_ick: ssi_l4_ick {
@@ -52,20 +81,19 @@
 		clock-div = <1>;
 	};
 
-	ssi_ick: ssi_ick_3430es2@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-ssi-interface-clock";
-		clocks = <&ssi_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <0>;
-	};
+	clock@c00 {
+		compatible = "ti,clksel";
+		reg = <0xc00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	usim_gate_fck: usim_gate_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&omap_96m_fck>;
-		ti,bit-shift = <9>;
-		reg = <0x0c00>;
+		usim_gate_fck: clock-usim-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "usim_gate_fck";
+			clocks = <&omap_96m_fck>;
+			ti,bit-shift = <9>;
+		};
 	};
 
 	sys_d2_ck: sys_d2_ck {
@@ -140,13 +168,20 @@
 		clock-div = <20>;
 	};
 
-	usim_mux_fck: usim_mux_fck@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&sys_ck>, <&sys_d2_ck>, <&omap_96m_d2_fck>, <&omap_96m_d4_fck>, <&omap_96m_d8_fck>, <&omap_96m_d10_fck>, <&dpll5_m2_d4_ck>, <&dpll5_m2_d8_ck>, <&dpll5_m2_d16_ck>, <&dpll5_m2_d20_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x0c40>;
-		ti,index-starts-at-one;
+	clock@c40 {
+		compatible = "ti,clksel";
+		reg = <0xc40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		usim_mux_fck: clock-usim-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "usim_mux_fck";
+			clocks = <&sys_ck>, <&sys_d2_ck>, <&omap_96m_d2_fck>, <&omap_96m_d4_fck>, <&omap_96m_d8_fck>, <&omap_96m_d10_fck>, <&dpll5_m2_d4_ck>, <&dpll5_m2_d8_ck>, <&dpll5_m2_d16_ck>, <&dpll5_m2_d20_ck>;
+			ti,bit-shift = <3>;
+			ti,index-starts-at-one;
+		};
 	};
 
 	usim_fck: usim_fck {
@@ -155,12 +190,19 @@
 		clocks = <&usim_gate_fck>, <&usim_mux_fck>;
 	};
 
-	usim_ick: usim_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <9>;
+	clock@c10 {
+		compatible = "ti,clksel";
+		reg = <0xc10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		usim_ick: clock-usim-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "usim_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <9>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/ti/omap/omap36xx.dtsi
index c618cb257d00..e6d8070c1bf8 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap36xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC
  *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
@@ -25,15 +22,16 @@
 
 			vbb-supply = <&abb_mpu_iva>;
 			clock-latency = <300000>; /* From omap-cpufreq driver */
+			#cooling-cells = <2>;
 		};
 	};
 
-	/* see Documentation/devicetree/bindings/opp/opp.txt */
 	cpu0_opp_table: opp-table {
 		compatible = "operating-points-v2-ti-cpu";
 		syscon = <&scm_conf>;
 
-		opp50-300000000 {
+		opp-50-300000000 {
+			/* OPP50 */
 			opp-hz = /bits/ 64 <300000000>;
 			/*
 			 * we currently only select the max voltage from table
@@ -51,31 +49,33 @@
 			opp-suspend;
 		};
 
-		opp100-600000000 {
+		opp-100-600000000 {
+			/* OPP100 */
 			opp-hz = /bits/ 64 <600000000>;
 			opp-microvolt = <1200000 1200000 1200000>,
 					 <1200000 1200000 1200000>;
 			opp-supported-hw = <0xffffffff 3>;
 		};
 
-		opp130-800000000 {
+		opp-130-800000000 {
+			/* OPP130 */
 			opp-hz = /bits/ 64 <800000000>;
 			opp-microvolt = <1325000 1325000 1325000>,
 					 <1325000 1325000 1325000>;
 			opp-supported-hw = <0xffffffff 3>;
 		};
 
-		opp1g-1000000000 {
+		opp-1000000000 {
+			/* OPP1G */
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <1375000 1375000 1375000>,
 					 <1375000 1375000 1375000>;
 			/* only on am/dm37x with speed-binned bit set */
 			opp-supported-hw = <0xffffffff 2>;
-			turbo-mode;
 		};
 	};
 
-	opp_supply_mpu_iva: opp_supply {
+	opp_supply_mpu_iva: opp-supply {
 		compatible = "ti,omap-opp-supply";
 		ti,absolute-max-voltage-uv = <1375000>;
 	};
@@ -223,6 +223,10 @@
 	};
 };
 
+&sdma {
+	compatible = "ti,omap3630-sdma", "ti,omap-sdma";
+};
+
 /* OMAP3630 needs dss_96m_fck for VENC */
 &venc {
 	clocks = <&dss_tv_fck>, <&dss_96m_fck>;
@@ -230,7 +234,7 @@
 };
 
 &ssi {
-	status = "ok";
+	status = "okay";
 
 	clocks = <&ssi_ssr_fck>,
 		 <&ssi_sst_fck>,
@@ -240,6 +244,10 @@
 		      "ssi_ick";
 };
 
+&usb_otg_target {
+	clocks = <&hsotgusb_ick_3430es2>;
+};
+
 /include/ "omap34xx-omap36xx-clocks.dtsi"
 /include/ "omap36xx-omap3430es2plus-clocks.dtsi"
 /include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
diff --git a/arch/arm/boot/dts/ti/omap/omap3xxx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap3xxx-clocks.dtsi
new file mode 100644
index 000000000000..2e13ca11ceea
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap3xxx-clocks.dtsi
@@ -0,0 +1,1790 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree Source for OMAP3 clock data
+ *
+ * Copyright (C) 2013 Texas Instruments, Inc.
+ */
+&prm_clocks {
+	virt_16_8m_ck: virt_16_8m_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <16800000>;
+	};
+
+	osc_sys_ck: osc_sys_ck@d40 {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&virt_12m_ck>, <&virt_13m_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_38_4m_ck>, <&virt_16_8m_ck>;
+		reg = <0x0d40>;
+	};
+
+	sys_ck: sys_ck@1270 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&osc_sys_ck>;
+		ti,bit-shift = <6>;
+		ti,max-div = <3>;
+		reg = <0x1270>;
+		ti,index-starts-at-one;
+	};
+
+	sys_clkout1: sys_clkout1@d70 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&osc_sys_ck>;
+		reg = <0x0d70>;
+		ti,bit-shift = <7>;
+	};
+
+	dpll3_x2_ck: dpll3_x2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll3_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll3_m2x2_ck: dpll3_m2x2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll3_m2_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll4_x2_ck: dpll4_x2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll4_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	corex2_fck: corex2_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll3_m2x2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	wkup_l4_ick: wkup_l4_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+};
+
+&scm_clocks {
+	/* CONTROL_DEVCONF1 */
+	clock@68 {
+		compatible = "ti,clksel";
+		reg = <0x68>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mcbsp5_mux_fck: clock-mcbsp5-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp5_mux_fck";
+			clocks = <&core_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <4>;
+		};
+
+		mcbsp3_mux_fck: clock-mcbsp3-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp3_mux_fck";
+			clocks = <&per_96m_fck>, <&mcbsp_clks>;
+		};
+
+		mcbsp4_mux_fck: clock-mcbsp4-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp4_mux_fck";
+			clocks = <&per_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <2>;
+		};
+	};
+
+	mcbsp5_fck: mcbsp5_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&mcbsp5_gate_fck>, <&mcbsp5_mux_fck>;
+	};
+
+	/* CONTROL_DEVCONF0 */
+	clock@4 {
+		compatible = "ti,clksel";
+		reg = <0x4>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mcbsp1_mux_fck: clock-mcbsp1-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp1_mux_fck";
+			clocks = <&core_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <2>;
+		};
+
+		mcbsp2_mux_fck: clock-mcbsp2-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp2_mux_fck";
+			clocks = <&per_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <6>;
+		};
+	};
+
+	mcbsp1_fck: mcbsp1_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&mcbsp1_gate_fck>, <&mcbsp1_mux_fck>;
+	};
+
+	mcbsp2_fck: mcbsp2_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&mcbsp2_gate_fck>, <&mcbsp2_mux_fck>;
+	};
+
+	mcbsp3_fck: mcbsp3_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&mcbsp3_gate_fck>, <&mcbsp3_mux_fck>;
+	};
+
+	mcbsp4_fck: mcbsp4_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&mcbsp4_gate_fck>, <&mcbsp4_mux_fck>;
+	};
+};
+&cm_clocks {
+	dummy_apb_pclk: dummy_apb_pclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0x0>;
+	};
+
+	omap_32k_fck: omap_32k_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	virt_12m_ck: virt_12m_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+	};
+
+	virt_13m_ck: virt_13m_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+	};
+
+	virt_19200000_ck: virt_19200000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <19200000>;
+	};
+
+	virt_26000000_ck: virt_26000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+	};
+
+	virt_38_4m_ck: virt_38_4m_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <38400000>;
+	};
+
+	dpll4_ck: dpll4_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-dpll-per-clock";
+		clocks = <&sys_ck>, <&sys_ck>;
+		reg = <0x0d00>, <0x0d20>, <0x0d44>, <0x0d30>;
+	};
+
+	dpll4_m2_ck: dpll4_m2_ck@d48 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll4_ck>;
+		ti,max-div = <63>;
+		reg = <0x0d48>;
+		ti,index-starts-at-one;
+	};
+
+	dpll4_m2x2_mul_ck: dpll4_m2x2_mul_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll4_m2_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll4_m2x2_ck: dpll4_m2x2_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll4_m2x2_mul_ck>;
+		ti,bit-shift = <0x1b>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+	};
+
+	omap_96m_alwon_fck: omap_96m_alwon_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll4_m2x2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dpll3_ck: dpll3_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-dpll-core-clock";
+		clocks = <&sys_ck>, <&sys_ck>;
+		reg = <0x0d00>, <0x0d20>, <0x0d40>, <0x0d30>;
+	};
+
+	/* CM_CLKSEL1_EMU */
+	clock@1140 {
+		compatible = "ti,clksel";
+		reg = <0x1140>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dpll3_m3_ck: clock-dpll3-m3 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll3_m3_ck";
+			clocks = <&dpll3_ck>;
+			ti,bit-shift = <16>;
+			ti,max-div = <31>;
+			ti,index-starts-at-one;
+		};
+
+		dpll4_m6_ck: clock-dpll4-m6 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll4_m6_ck";
+			clocks = <&dpll4_ck>;
+			ti,bit-shift = <24>;
+			ti,max-div = <63>;
+			ti,index-starts-at-one;
+		};
+
+		emu_src_mux_ck: clock-emu-src-mux {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "emu_src_mux_ck";
+			clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
+		};
+
+		pclk_fck: clock-pclk-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "pclk_fck";
+			clocks = <&emu_src_ck>;
+			ti,bit-shift = <8>;
+			ti,max-div = <7>;
+			ti,index-starts-at-one;
+		};
+
+		pclkx2_fck: clock-pclkx2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "pclkx2_fck";
+			clocks = <&emu_src_ck>;
+			ti,bit-shift = <6>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		atclk_fck: clock-atclk-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "atclk_fck";
+			clocks = <&emu_src_ck>;
+			ti,bit-shift = <4>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		traceclk_src_fck: clock-traceclk-src-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "traceclk_src_fck";
+			clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
+			ti,bit-shift = <2>;
+		};
+
+		traceclk_fck: clock-traceclk-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "traceclk_fck";
+			clocks = <&traceclk_src_fck>;
+			ti,bit-shift = <11>;
+			ti,max-div = <7>;
+			ti,index-starts-at-one;
+		};
+	};
+
+	dpll3_m3x2_mul_ck: dpll3_m3x2_mul_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll3_m3_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll3_m3x2_ck: dpll3_m3x2_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll3_m3x2_mul_ck>;
+		ti,bit-shift = <0xc>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+	};
+
+	emu_core_alwon_ck: emu_core_alwon_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll3_m3x2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	sys_altclk: sys_altclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0x0>;
+	};
+
+	mcbsp_clks: mcbsp_clks {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0x0>;
+	};
+
+	core_ck: core_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll3_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dpll1_fck: dpll1_fck@940 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&core_ck>;
+		ti,bit-shift = <19>;
+		ti,max-div = <7>;
+		reg = <0x0940>;
+		ti,index-starts-at-one;
+	};
+
+	dpll1_ck: dpll1_ck@904 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-dpll-clock";
+		clocks = <&sys_ck>, <&dpll1_fck>;
+		reg = <0x0904>, <0x0924>, <0x0940>, <0x0934>;
+	};
+
+	dpll1_x2_ck: dpll1_x2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll1_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll1_x2m2_ck: dpll1_x2m2_ck@944 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll1_x2_ck>;
+		ti,max-div = <31>;
+		reg = <0x0944>;
+		ti,index-starts-at-one;
+	};
+
+	cm_96m_fck: cm_96m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_96m_alwon_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_CLKSEL1_PLL */
+	clock@d40 {
+		compatible = "ti,clksel";
+		reg = <0xd40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dpll3_m2_ck: clock-dpll3-m2 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll3_m2_ck";
+			clocks = <&dpll3_ck>;
+			ti,bit-shift = <27>;
+			ti,max-div = <31>;
+			ti,index-starts-at-one;
+		};
+
+		omap_96m_fck: clock-omap-96m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "omap_96m_fck";
+			clocks = <&cm_96m_fck>, <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		omap_54m_fck: clock-omap-54m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "omap_54m_fck";
+			clocks = <&dpll4_m3x2_ck>, <&sys_altclk>;
+			ti,bit-shift = <5>;
+		};
+
+		omap_48m_fck: clock-omap-48m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "omap_48m_fck";
+			clocks = <&cm_96m_d2_fck>, <&sys_altclk>;
+			ti,bit-shift = <3>;
+		};
+	};
+
+	/* CM_CLKSEL_DSS */
+	clock@e40 {
+		compatible = "ti,clksel";
+		reg = <0xe40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dpll4_m3_ck: clock-dpll4-m3 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll4_m3_ck";
+			clocks = <&dpll4_ck>;
+			ti,bit-shift = <8>;
+			ti,max-div = <32>;
+			ti,index-starts-at-one;
+		};
+
+		dpll4_m4_ck: clock-dpll4-m4 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll4_m4_ck";
+			clocks = <&dpll4_ck>;
+			ti,max-div = <16>;
+			ti,index-starts-at-one;
+		};
+	};
+
+	dpll4_m3x2_mul_ck: dpll4_m3x2_mul_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll4_m3_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll4_m3x2_ck: dpll4_m3x2_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll4_m3x2_mul_ck>;
+		ti,bit-shift = <0x1c>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+	};
+
+	cm_96m_d2_fck: cm_96m_d2_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&cm_96m_fck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	omap_12m_fck: omap_12m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_48m_fck>;
+		clock-mult = <1>;
+		clock-div = <4>;
+	};
+
+	dpll4_m4x2_mul_ck: dpll4_m4x2_mul_ck {
+		#clock-cells = <0>;
+		compatible = "ti,fixed-factor-clock";
+		clocks = <&dpll4_m4_ck>;
+		ti,clock-mult = <2>;
+		ti,clock-div = <1>;
+		ti,set-rate-parent;
+	};
+
+	dpll4_m4x2_ck: dpll4_m4x2_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll4_m4x2_mul_ck>;
+		ti,bit-shift = <0x1d>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+		ti,set-rate-parent;
+	};
+
+	dpll4_m5_ck: dpll4_m5_ck@f40 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll4_ck>;
+		ti,max-div = <63>;
+		reg = <0x0f40>;
+		ti,index-starts-at-one;
+	};
+
+	dpll4_m5x2_mul_ck: dpll4_m5x2_mul_ck {
+		#clock-cells = <0>;
+		compatible = "ti,fixed-factor-clock";
+		clocks = <&dpll4_m5_ck>;
+		ti,clock-mult = <2>;
+		ti,clock-div = <1>;
+		ti,set-rate-parent;
+	};
+
+	dpll4_m5x2_ck: dpll4_m5x2_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll4_m5x2_mul_ck>;
+		ti,bit-shift = <0x1e>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+		ti,set-rate-parent;
+	};
+
+	dpll4_m6x2_mul_ck: dpll4_m6x2_mul_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll4_m6_ck>;
+		clock-mult = <2>;
+		clock-div = <1>;
+	};
+
+	dpll4_m6x2_ck: dpll4_m6x2_ck@d00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll4_m6x2_mul_ck>;
+		ti,bit-shift = <0x1f>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+	};
+
+	emu_per_alwon_ck: emu_per_alwon_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll4_m6x2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_CLKOUT_CTRL */
+	clock@d70 {
+		compatible = "ti,clksel";
+		reg = <0xd70>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		clkout2_src_gate_ck: clock-clkout2-src-gate {
+			#clock-cells = <0>;
+			compatible = "ti,composite-no-wait-gate-clock";
+			clock-output-names = "clkout2_src_gate_ck";
+			clocks = <&core_ck>;
+			ti,bit-shift = <7>;
+		};
+
+		clkout2_src_mux_ck: clock-clkout2-src-mux {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "clkout2_src_mux_ck";
+			clocks = <&core_ck>, <&sys_ck>, <&cm_96m_fck>, <&omap_54m_fck>;
+		};
+
+		sys_clkout2: clock-sys-clkout2 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "sys_clkout2";
+			clocks = <&clkout2_src_ck>;
+			ti,bit-shift = <3>;
+			ti,max-div = <64>;
+			ti,index-power-of-two;
+		};
+	};
+
+	clkout2_src_ck: clkout2_src_ck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&clkout2_src_gate_ck>, <&clkout2_src_mux_ck>;
+	};
+
+	mpu_ck: mpu_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll1_x2m2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	arm_fck: arm_fck@924 {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&mpu_ck>;
+		reg = <0x0924>;
+		ti,max-div = <2>;
+	};
+
+	emu_mpu_alwon_ck: emu_mpu_alwon_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&mpu_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_CLKSEL_CORE */
+	clock@a40 {
+		compatible = "ti,clksel";
+		reg = <0xa40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		l3_ick: clock-l3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "l3_ick";
+			clocks = <&core_ck>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		l4_ick: clock-l4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "l4_ick";
+			clocks = <&l3_ick>;
+			ti,bit-shift = <2>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		gpt10_mux_fck: clock-gpt10-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt10_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt11_mux_fck: clock-gpt11-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt11_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
+	};
+
+	/* CM_CLKSEL_WKUP */
+	clock@c40 {
+		compatible = "ti,clksel";
+		reg = <0xc40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		rm_ick: clock-rm-ick {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "rm_ick";
+			clocks = <&l4_ick>;
+			ti,bit-shift = <1>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		gpt1_mux_fck: clock-gpt1-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt1_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+		};
+	};
+
+	/* CM_FCLKEN1_CORE */
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpt10_gate_fck: clock-gpt10-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt10_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <11>;
+		};
+
+		gpt11_gate_fck: clock-gpt11-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt11_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <12>;
+		};
+
+		mmchs2_fck: clock-mmchs2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mmchs2_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <25>;
+		};
+
+		mmchs1_fck: clock-mmchs1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mmchs1_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <24>;
+		};
+
+		i2c3_fck: clock-i2c3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "i2c3_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <17>;
+		};
+
+		i2c2_fck: clock-i2c2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "i2c2_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <16>;
+		};
+
+		i2c1_fck: clock-i2c1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "i2c1_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <15>;
+		};
+
+		mcbsp5_gate_fck: clock-mcbsp5-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp5_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <10>;
+		};
+
+		mcbsp1_gate_fck: clock-mcbsp1-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp1_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <9>;
+		};
+
+		mcspi4_fck: clock-mcspi4-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi4_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <21>;
+		};
+
+		mcspi3_fck: clock-mcspi3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi3_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <20>;
+		};
+
+		mcspi2_fck: clock-mcspi2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi2_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <19>;
+		};
+
+		mcspi1_fck: clock-mcspi1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi1_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <18>;
+		};
+
+		uart2_fck: clock-uart2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart2_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <14>;
+		};
+
+		uart1_fck: clock-uart1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart1_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <13>;
+		};
+
+		hdq_fck: clock-hdq-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "hdq_fck";
+			clocks = <&core_12m_fck>;
+			ti,bit-shift = <22>;
+		};
+	};
+
+	gpt10_fck: gpt10_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt10_gate_fck>, <&gpt10_mux_fck>;
+	};
+
+	gpt11_fck: gpt11_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt11_gate_fck>, <&gpt11_mux_fck>;
+	};
+
+	core_96m_fck: core_96m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_96m_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	core_48m_fck: core_48m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_48m_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	core_12m_fck: core_12m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_12m_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	core_l3_ick: core_l3_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l3_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_ICLKEN1_CORE */
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		sdrc_ick: clock-sdrc-ick {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "sdrc_ick";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <1>;
+		};
+
+		mmchs2_ick: clock-mmchs2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mmchs2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <25>;
+		};
+
+		mmchs1_ick: clock-mmchs1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mmchs1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <24>;
+		};
+
+		hdq_ick: clock-hdq-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "hdq_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <22>;
+		};
+
+		mcspi4_ick: clock-mcspi4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi4_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <21>;
+		};
+
+		mcspi3_ick: clock-mcspi3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi3_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <20>;
+		};
+
+		mcspi2_ick: clock-mcspi2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <19>;
+		};
+
+		mcspi1_ick: clock-mcspi1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <18>;
+		};
+
+		i2c3_ick: clock-i2c3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "i2c3_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <17>;
+		};
+
+		i2c2_ick: clock-i2c2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "i2c2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <16>;
+		};
+
+		i2c1_ick: clock-i2c1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "i2c1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <15>;
+		};
+
+		uart2_ick: clock-uart2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <14>;
+		};
+
+		uart1_ick: clock-uart1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <13>;
+		};
+
+		gpt11_ick: clock-gpt11-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt11_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <12>;
+		};
+
+		gpt10_ick: clock-gpt10-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt10_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <11>;
+		};
+
+		mcbsp5_ick: clock-mcbsp5-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp5_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <10>;
+		};
+
+		mcbsp1_ick: clock-mcbsp1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <9>;
+		};
+
+		omapctrl_ick: clock-omapctrl-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "omapctrl_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <6>;
+		};
+
+		aes2_ick: clock-aes2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "aes2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <28>;
+		};
+
+		sha12_ick: clock-sha12-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "sha12_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <27>;
+		};
+	};
+
+	gpmc_fck: gpmc_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&core_l3_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	core_l4_ick: core_l4_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l4_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_FCLKEN_DSS */
+	clock@e00 {
+		compatible = "ti,clksel";
+		reg = <0xe00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dss_tv_fck: clock-dss-tv-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss_tv_fck";
+			clocks = <&omap_54m_fck>;
+			ti,bit-shift = <2>;
+		};
+
+		dss_96m_fck: clock-dss-96m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss_96m_fck";
+			clocks = <&omap_96m_fck>;
+			ti,bit-shift = <2>;
+		};
+
+		dss2_alwon_fck: clock-dss2-alwon-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss2_alwon_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <1>;
+		};
+	};
+
+	dummy_ck: dummy_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	/* CM_FCLKEN_WKUP */
+	clock@c00 {
+		compatible = "ti,clksel";
+		reg = <0xc00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpt1_gate_fck: clock-gpt1-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt1_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <0>;
+		};
+
+		gpio1_dbck: clock-gpio1-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio1_dbck";
+			clocks = <&wkup_32k_fck>;
+			ti,bit-shift = <3>;
+		};
+
+		wdt2_fck: clock-wdt2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "wdt2_fck";
+			clocks = <&wkup_32k_fck>;
+			ti,bit-shift = <5>;
+		};
+	};
+
+	gpt1_fck: gpt1_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt1_gate_fck>, <&gpt1_mux_fck>;
+	};
+
+	wkup_32k_fck: wkup_32k_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_32k_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_ICLKEN_WKUP */
+	clock@c10 {
+		compatible = "ti,clksel";
+		reg = <0xc10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		wdt2_ick: clock-wdt2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "wdt2_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <5>;
+		};
+
+		wdt1_ick: clock-wdt1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "wdt1_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		gpio1_ick: clock-gpio1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio1_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <3>;
+		};
+
+		omap_32ksync_ick: clock-omap-32ksync-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "omap_32ksync_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <2>;
+		};
+
+		gpt12_ick: clock-gpt12-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt12_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <1>;
+		};
+
+		gpt1_ick: clock-gpt1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt1_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <0>;
+		};
+	};
+
+	per_96m_fck: per_96m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_96m_alwon_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	per_48m_fck: per_48m_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_48m_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_FCLKEN_PER */
+	clock@1000 {
+		compatible = "ti,clksel";
+		reg = <0x1000>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		uart3_fck: clock-uart3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart3_fck";
+			clocks = <&per_48m_fck>;
+			ti,bit-shift = <11>;
+		};
+
+		gpt2_gate_fck: clock-gpt2-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt2_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <3>;
+		};
+
+		gpt3_gate_fck: clock-gpt3-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt3_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <4>;
+		};
+
+		gpt4_gate_fck: clock-gpt4-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt4_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <5>;
+		};
+
+		gpt5_gate_fck: clock-gpt5-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt5_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt6_gate_fck: clock-gpt6-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt6_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
+
+		gpt7_gate_fck: clock-gpt7-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt7_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <8>;
+		};
+
+		gpt8_gate_fck: clock-gpt8-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt8_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <9>;
+		};
+
+		gpt9_gate_fck: clock-gpt9-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt9_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <10>;
+		};
+
+		gpio6_dbck: clock-gpio6-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio6_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <17>;
+		};
+
+		gpio5_dbck: clock-gpio5-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio5_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <16>;
+		};
+
+		gpio4_dbck: clock-gpio4-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio4_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <15>;
+		};
+
+		gpio3_dbck: clock-gpio3-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio3_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <14>;
+		};
+
+		gpio2_dbck: clock-gpio2-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio2_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <13>;
+		};
+
+		wdt3_fck: clock-wdt3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "wdt3_fck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <12>;
+		};
+
+		mcbsp2_gate_fck: clock-mcbsp2-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp2_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <0>;
+		};
+
+		mcbsp3_gate_fck: clock-mcbsp3-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp3_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <1>;
+		};
+
+		mcbsp4_gate_fck: clock-mcbsp4-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp4_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <2>;
+		};
+	};
+
+	/* CM_CLKSEL_PER */
+	clock@1040 {
+		compatible = "ti,clksel";
+		reg = <0x1040>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpt2_mux_fck: clock-gpt2-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt2_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+		};
+
+		gpt3_mux_fck: clock-gpt3-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt3_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <1>;
+		};
+
+		gpt4_mux_fck: clock-gpt4-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt4_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <2>;
+		};
+
+		gpt5_mux_fck: clock-gpt5-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt5_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <3>;
+		};
+
+		gpt6_mux_fck: clock-gpt6-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt6_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <4>;
+		};
+
+		gpt7_mux_fck: clock-gpt7-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt7_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <5>;
+		};
+
+		gpt8_mux_fck: clock-gpt8-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt8_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt9_mux_fck: clock-gpt9-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt9_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
+	};
+
+	gpt2_fck: gpt2_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt2_gate_fck>, <&gpt2_mux_fck>;
+	};
+
+	gpt3_fck: gpt3_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt3_gate_fck>, <&gpt3_mux_fck>;
+	};
+
+	gpt4_fck: gpt4_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt4_gate_fck>, <&gpt4_mux_fck>;
+	};
+
+	gpt5_fck: gpt5_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt5_gate_fck>, <&gpt5_mux_fck>;
+	};
+
+	gpt6_fck: gpt6_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt6_gate_fck>, <&gpt6_mux_fck>;
+	};
+
+	gpt7_fck: gpt7_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt7_gate_fck>, <&gpt7_mux_fck>;
+	};
+
+	gpt8_fck: gpt8_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt8_gate_fck>, <&gpt8_mux_fck>;
+	};
+
+	gpt9_fck: gpt9_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-clock";
+		clocks = <&gpt9_gate_fck>, <&gpt9_mux_fck>;
+	};
+
+	per_32k_alwon_fck: per_32k_alwon_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&omap_32k_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	per_l4_ick: per_l4_ick {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&l4_ick>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	/* CM_ICLKEN_PER */
+	clock@1010 {
+		compatible = "ti,clksel";
+		reg = <0x1010>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpio6_ick: clock-gpio6-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio6_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <17>;
+		};
+
+		gpio5_ick: clock-gpio5-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio5_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <16>;
+		};
+
+		gpio4_ick: clock-gpio4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <15>;
+		};
+
+		gpio3_ick: clock-gpio3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <14>;
+		};
+
+		gpio2_ick: clock-gpio2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio2_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <13>;
+		};
+
+		wdt3_ick: clock-wdt3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "wdt3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <12>;
+		};
+
+		uart3_ick: clock-uart3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <11>;
+		};
+
+		uart4_ick: clock-uart4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <18>;
+		};
+
+		gpt9_ick: clock-gpt9-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt9_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <10>;
+		};
+
+		gpt8_ick: clock-gpt8-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt8_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <9>;
+		};
+
+		gpt7_ick: clock-gpt7-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt7_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <8>;
+		};
+
+		gpt6_ick: clock-gpt6-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt6_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <7>;
+		};
+
+		gpt5_ick: clock-gpt5-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt5_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt4_ick: clock-gpt4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <5>;
+		};
+
+		gpt3_ick: clock-gpt3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		gpt2_ick: clock-gpt2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt2_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <3>;
+		};
+
+		mcbsp2_ick: clock-mcbsp2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp2_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <0>;
+		};
+
+		mcbsp3_ick: clock-mcbsp3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <1>;
+		};
+
+		mcbsp4_ick: clock-mcbsp4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <2>;
+		};
+	};
+
+	emu_src_ck: emu_src_ck {
+		#clock-cells = <0>;
+		compatible = "ti,clkdm-gate-clock";
+		clocks = <&emu_src_mux_ck>;
+	};
+
+	secure_32k_fck: secure_32k_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	gpt12_fck: gpt12_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&secure_32k_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	wdt1_fck: wdt1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&secure_32k_fck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+};
+
+&cm_clockdomains {
+	core_l3_clkdm: core_l3_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&sdrc_ick>;
+	};
+
+	dpll3_clkdm: dpll3_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&dpll3_ck>;
+	};
+
+	dpll1_clkdm: dpll1_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&dpll1_ck>;
+	};
+
+	per_clkdm: per_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&uart3_fck>, <&gpio6_dbck>, <&gpio5_dbck>,
+			 <&gpio4_dbck>, <&gpio3_dbck>, <&gpio2_dbck>,
+			 <&wdt3_fck>, <&gpio6_ick>, <&gpio5_ick>, <&gpio4_ick>,
+			 <&gpio3_ick>, <&gpio2_ick>, <&wdt3_ick>, <&uart3_ick>,
+			 <&uart4_ick>, <&gpt9_ick>, <&gpt8_ick>, <&gpt7_ick>,
+			 <&gpt6_ick>, <&gpt5_ick>, <&gpt4_ick>, <&gpt3_ick>,
+			 <&gpt2_ick>, <&mcbsp2_ick>, <&mcbsp3_ick>,
+			 <&mcbsp4_ick>;
+	};
+
+	emu_clkdm: emu_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&emu_src_ck>;
+	};
+
+	dpll4_clkdm: dpll4_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&dpll4_ck>;
+	};
+
+	wkup_clkdm: wkup_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>,
+			 <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>,
+			 <&gpt1_ick>;
+	};
+
+	dss_clkdm: dss_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>;
+	};
+
+	core_l4_clkdm: core_l4_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>,
+			 <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>,
+			 <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>,
+			 <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>,
+			 <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>,
+			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
+			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
+			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
+			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>;
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/omap4-cpu-thermal.dtsi b/arch/arm/boot/dts/ti/omap/omap4-cpu-thermal.dtsi
new file mode 100644
index 000000000000..d484ec1e4fd8
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-cpu-thermal.dtsi
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device Tree Source for OMAP4/5 SoC CPU thermal
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
+ * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+cpu_thermal: cpu_thermal {
+	polling-delay-passive = <250>; /* milliseconds */
+	polling-delay = <1000>; /* milliseconds */
+
+	/*
+	 * See 44xx files for single sensor addressing, omap5 and dra7 need
+	 * also sensor ID for addressing.
+	 */
+	thermal-sensors = <&bandgap     0>;
+
+	cpu_trips: trips {
+		cpu_alert0: cpu_alert {
+			temperature = <100000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "passive";
+		};
+		cpu_crit: cpu_crit {
+			temperature = <125000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "critical";
+		};
+	};
+
+	cpu_cooling_maps: cooling-maps {
+		map0 {
+			trip = <&cpu_alert0>;
+			cooling-device =
+				<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/omap4-droid-bionic-xt875.dts b/arch/arm/boot/dts/ti/omap/omap4-droid-bionic-xt875.dts
new file mode 100644
index 000000000000..1d9000f84f1b
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-droid-bionic-xt875.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-xt8xx.dtsi"
+
+/ {
+	model = "Motorola Droid Bionic XT875";
+	compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display0 = &lcd0;
+		display1 = &hdmi0;
+	};
+};
+
+&keypad {
+	keypad,num-rows = <8>;
+	keypad,num-columns = <8>;
+	linux,keymap = <
+	MATRIX_KEY(5, 0, KEY_VOLUMEUP)
+	MATRIX_KEY(3, 0, KEY_VOLUMEDOWN)
+	>;
+};
+
+&i2c1 {
+	led-controller@38 {
+		compatible = "ti,lm3532";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x38>;
+
+		enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+
+		ramp-up-us = <1024>;
+		ramp-down-us = <8193>;
+
+		backlight_led: led@0 {
+			reg = <0>;
+			led-sources = <2>;
+			ti,led-mode = <0>;
+			label = ":backlight";
+		};
+	};
+};
+
+&i2c4 {
+	kxtf9: accelerometer@f {
+		compatible = "kionix,kxtf9";
+		reg = <0x0f>;
+
+		vdd-supply = <&vhvio>;
+
+		interrupt-parent = <&gpio2>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+
+		rotation-matrix = "0", "-1", "0",
+				  "1", "0", "0",
+				  "0", "0", "1";
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/omap4-droid4-xt894.dts b/arch/arm/boot/dts/ti/omap/omap4-droid4-xt894.dts
new file mode 100644
index 000000000000..cc3f3e1b65ea
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-droid4-xt894.dts
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-xt8xx.dtsi"
+
+/ {
+	model = "Motorola Droid 4 XT894";
+	compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display0 = &lcd0;
+		display1 = &hdmi0;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		volume_down {
+			label = "Volume Down";
+			gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
+			linux,code = <KEY_VOLUMEDOWN>;
+			linux,can-disable;
+			/* Value above 7.95ms for no GPIO hardware debounce */
+			debounce-interval = <10>;
+		};
+
+		/*
+		 * We use pad 0x4a100116 abe_dmic_din3.gpio_122 as the irq instead
+		 * of the gpio interrupt to avoid lost events in deeper idle states.
+		*/
+		slider {
+			label = "Keypad Slide";
+			interrupts-extended = <&omap4_pmx_core 0xd6>;
+			gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_KEYPAD_SLIDE>;
+			linux,can-disable;
+			/* Value above 7.95ms for no GPIO hardware debounce */
+			debounce-interval = <10>;
+		};
+	};
+};
+
+&keypad {
+	keypad,num-rows = <8>;
+	keypad,num-columns = <8>;
+	linux,keymap = <
+
+	/* Row 1 */
+	MATRIX_KEY(0, 2, KEY_1)
+	MATRIX_KEY(0, 6, KEY_2)
+	MATRIX_KEY(2, 3, KEY_3)
+	MATRIX_KEY(0, 7, KEY_4)
+	MATRIX_KEY(0, 4, KEY_5)
+	MATRIX_KEY(5, 5, KEY_6)
+	MATRIX_KEY(0, 1, KEY_7)
+	MATRIX_KEY(0, 5, KEY_8)
+	MATRIX_KEY(0, 0, KEY_9)
+	MATRIX_KEY(1, 6, KEY_0)
+
+	/* Row 2 */
+	MATRIX_KEY(3, 4, KEY_APOSTROPHE)
+	MATRIX_KEY(7, 6, KEY_Q)
+	MATRIX_KEY(7, 7, KEY_W)
+	MATRIX_KEY(7, 2, KEY_E)
+	MATRIX_KEY(1, 0, KEY_R)
+	MATRIX_KEY(4, 4, KEY_T)
+	MATRIX_KEY(1, 2, KEY_Y)
+	MATRIX_KEY(6, 7, KEY_U)
+	MATRIX_KEY(2, 2, KEY_I)
+	MATRIX_KEY(5, 6, KEY_O)
+	MATRIX_KEY(3, 7, KEY_P)
+	MATRIX_KEY(6, 5, KEY_BACKSPACE)
+
+	/* Row 3 */
+	MATRIX_KEY(5, 4, KEY_TAB)
+	MATRIX_KEY(5, 7, KEY_A)
+	MATRIX_KEY(2, 7, KEY_S)
+	MATRIX_KEY(7, 0, KEY_D)
+	MATRIX_KEY(2, 6, KEY_F)
+	MATRIX_KEY(6, 2, KEY_G)
+	MATRIX_KEY(6, 6, KEY_H)
+	MATRIX_KEY(1, 4, KEY_J)
+	MATRIX_KEY(3, 1, KEY_K)
+	MATRIX_KEY(2, 1, KEY_L)
+	MATRIX_KEY(4, 6, KEY_ENTER)
+
+	/* Row 4 */
+	MATRIX_KEY(3, 6, KEY_LEFTSHIFT)		/* KEY_CAPSLOCK */
+	MATRIX_KEY(6, 1, KEY_Z)
+	MATRIX_KEY(7, 4, KEY_X)
+	MATRIX_KEY(5, 1, KEY_C)
+	MATRIX_KEY(1, 7, KEY_V)
+	MATRIX_KEY(2, 4, KEY_B)
+	MATRIX_KEY(4, 1, KEY_N)
+	MATRIX_KEY(1, 1, KEY_M)
+	MATRIX_KEY(3, 5, KEY_COMMA)
+	MATRIX_KEY(5, 2, KEY_DOT)
+	MATRIX_KEY(6, 3, KEY_UP)
+	MATRIX_KEY(7, 3, KEY_OK)
+
+	/* Row 5 */
+	MATRIX_KEY(2, 5, KEY_LEFTCTRL)		/* KEY_LEFTSHIFT */
+	MATRIX_KEY(4, 5, KEY_LEFTALT)		/* SYM */
+	MATRIX_KEY(6, 0, KEY_MINUS)
+	MATRIX_KEY(4, 7, KEY_EQUAL)
+	MATRIX_KEY(1, 5, KEY_SPACE)
+	MATRIX_KEY(3, 2, KEY_SLASH)
+	MATRIX_KEY(4, 3, KEY_LEFT)
+	MATRIX_KEY(5, 3, KEY_DOWN)
+	MATRIX_KEY(3, 3, KEY_RIGHT)
+
+	/* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
+	MATRIX_KEY(5, 0, KEY_VOLUMEUP)
+	>;
+};
+
+&i2c1 {
+	led-controller@38 {
+		compatible = "ti,lm3532";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x38>;
+
+		enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+
+		ramp-up-us = <1024>;
+		ramp-down-us = <8193>;
+
+		backlight_led: led@0 {
+			reg = <0>;
+			led-sources = <2>;
+			ti,led-mode = <0>;
+			label = ":backlight";
+		};
+
+		led@1 {
+			reg = <1>;
+			led-sources = <1>;
+			ti,led-mode = <0>;
+			label = ":kbd_backlight";
+		};
+	};
+};
+
+&i2c4 {
+	lis3dh: accelerometer@18 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x18>;
+
+		vdd-supply = <&vhvio>;
+
+		interrupt-parent = <&gpio2>;
+		interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
+
+		rotation-matrix = "0", "-1", "0",
+				  "1", "0", "0",
+				  "0", "0", "1";
+	};
+};
diff --git a/arch/arm/boot/dts/omap4-duovero-parlor.dts b/arch/arm/boot/dts/ti/omap/omap4-duovero-parlor.dts
index 8047e8cdb3af..6d1beb453234 100644
--- a/arch/arm/boot/dts/omap4-duovero-parlor.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-duovero-parlor.dts
@@ -62,33 +62,33 @@
 			&smsc_pins
 	>;
 
-	led_pins: pinmux_led_pins {
+	led_pins: led-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x116, PIN_OUTPUT | MUX_MODE3)		/* abe_dmic_din3.gpio_122 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3)	/* abe_dmic_din2.gpio_121 */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
 			OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
 			OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	smsc_pins: pinmux_smsc_pins {
+	smsc_pins: smsc-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x068, PIN_INPUT | MUX_MODE3)		/* gpmc_a20.gpio_44: IRQ */
 			OMAP4_IOPAD(0x06a, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a21.gpio_45: nReset */
@@ -96,7 +96,7 @@
 		>;
 	};
 
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)		/* hdmi_hpd.gpio_63 */
 			OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)		/* hdmi_cec.hdmi_cec */
@@ -139,7 +139,7 @@
 	ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;	/* gpio_44 */
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;		/* gpio_44 */
 
 		phy-mode = "mii";
 
@@ -171,11 +171,11 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 	vdda-supply = <&vdac>;
 
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/omap4-duovero.dtsi b/arch/arm/boot/dts/ti/omap/omap4-duovero.dtsi
index 805dfd40030d..b8af455b411a 100644
--- a/arch/arm/boot/dts/omap4-duovero.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-duovero.dtsi
@@ -73,14 +73,14 @@
 			&hsusbb1_pins
 	>;
 
-	twl6040_pins: pinmux_twl6040_pins {
+	twl6040_pins: twl6040-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE3)		/* usbb2_ulpitll_nxt.gpio_160 */
 			OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0)		/* sys_nirq2.sys_nirq2 */
 		>;
 	};
 
-	mcbsp1_pins: pinmux_mcbsp1_pins {
+	mcbsp1_pins: mcbsp1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
 			OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dr.abe_mcbsp1_dr */
@@ -89,7 +89,7 @@
 		>;
 	};
 
-	hsusbb1_pins: pinmux_hsusbb1_pins {
+	hsusbb1_pins: hsusbb1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
 			OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4)		/* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
@@ -106,34 +106,34 @@
 		>;
 	};
 
-	hsusb1phy_pins: pinmux_hsusb1phy_pins {
+	hsusb1phy_pins: hsusb1phy-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x08c, PIN_OUTPUT | MUX_MODE3)		/* gpmc_wait1.gpio_62 */
 		>;
 	};
 
-	w2cbw0015_pins: pinmux_w2cbw0015_pins {
+	w2cbw0015_pins: w2cbw0015-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
 			OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
 			OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk */
 			OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmcc1_cmd */
@@ -144,7 +144,7 @@
 		>;
 	};
 
-	mmc5_pins: pinmux_mmc5_pins {
+	mmc5_pins: mmc5-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk */
 			OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmcc5_cmd */
diff --git a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
new file mode 100644
index 000000000000..24f7d0285f79
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023 Andreas Kemnade
+ */
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include "omap4460.dtsi"
+
+/ {
+	model = "Epson Moverio BT-200";
+	compatible = "epson,embt2ws", "ti,omap4460", "ti,omap4";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1024M */
+	};
+
+	backlight-left {
+		compatible = "pwm-backlight";
+		pwms = <&twl_pwm 1 7812500>;
+		power-supply = <&unknown_supply>;
+	};
+
+	backlight-right {
+		compatible = "pwm-backlight";
+		pwms = <&twl_pwm 0 7812500>;
+		power-supply = <&unknown_supply>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		key-lock {
+			label = "Lock";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_ROTATE_LOCK>; /* SW_TOUCHPAD_LOCK */
+			linux,input-type = <EV_SW>;
+		};
+	};
+
+	unknown_supply: unknown-supply {
+		compatible = "regulator-fixed";
+		regulator-name = "unknown";
+	};
+
+	wl12xx_pwrseq: wl12xx-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&twl 1>;
+		clock-names = "ext_clock";
+	};
+
+       /* regulator for wl12xx on sdio2 */
+	wl12xx_vmmc: wl12xx-vmmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	clock-frequency = <400000>;
+
+	twl: pmic@48 {
+		compatible = "ti,twl6032";
+		reg = <0x48>;
+		#clock-cells = <1>;
+		/* IRQ# = 7 */
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		rtc {
+			compatible = "ti,twl4030-rtc";
+			interrupts = <11>;
+		};
+
+		ldo2: regulator-ldo2 {
+			compatible = "ti,twl6032-ldo2";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		ldo4: regulator-ldo4 {
+			compatible = "ti,twl6032-ldo4";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		ldo3: regulator-ldo3 {
+			compatible = "ti,twl6032-ldo3";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		ldo5: regulator-ldo5 {
+			compatible = "ti,twl6032-ldo5";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3000000>;
+			ti,retain-on-reset;
+		};
+
+		ldo1: regulator-ldo1 {
+			compatible = "ti,twl6032-ldo1";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2500000>;
+		};
+
+		ldo7: regulator-ldo7 {
+			compatible = "ti,twl6032-ldo7";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		ldoln: regulator-ldoln {
+			compatible = "ti,twl6032-ldoln";
+			regulator-always-on;
+		};
+
+		ldo6: regulator-ldo6 {
+			compatible = "ti,twl6032-ldo6";
+			regulator-always-on;
+		};
+
+		ldousb: regulator-ldousb {
+			compatible = "ti,twl6032-ldousb";
+			regulator-always-on;
+		};
+
+		vio: regulator-vio {
+			compatible = "ti,twl6032-vio";
+			regulator-always-on;
+		};
+
+		twl_usb_comparator: usb-comparator {
+			compatible = "ti,twl6030-usb";
+			interrupts = <4>, <10>;
+		};
+
+		twl_pwm: pwm {
+			/* provides two PWMs (id 0, 1 for PWM1 and PWM2) */
+			compatible = "ti,twl6030-pwm";
+			#pwm-cells = <2>;
+		};
+
+		twl_pwmled: pwmled {
+			/* provides one PWM (id 0 for Charging indicator LED) */
+			compatible = "ti,twl6030-pwmled";
+			#pwm-cells = <2>;
+		};
+
+		gpadc {
+			compatible = "ti,twl6032-gpadc";
+			interrupts = <3>;
+			#io-channel-cells = <1>;
+		};
+
+	};
+};
+
+#include "twl6030_omap4.dtsi"
+
+&twl_usb_comparator {
+	usb-supply = <&ldousb>;
+};
+
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	clock-frequency = <200000>;
+
+	/* at head/glasses */
+	mpu9150h: imu@68 {
+		compatible = "invensense,mpu9150";
+		reg = <0x68>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu9150h_pins>;
+		interrupt-parent = <&gpio2>;
+		interrupt = <19 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	clock-frequency = <100000>;
+
+	led-controller@66 {
+		compatible = "rohm,bd2606mvv";
+		reg = <0x66>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led@4 {
+			reg = <4>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
+	clock-frequency = <360000>;
+
+	/* TODO: KXTI9 at 0xf */
+
+	tlv320aic3x: codec@18 {
+		compatible = "ti,tlv320aic3x";
+		reg = <0x18>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tlv320aic3x_pins>;
+		#sound-dai-cells = <0>;
+
+		reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+	};
+
+	mpu9150: imu@68 {
+		compatible = "invensense,mpu9150";
+		reg = <0x68>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu9150_pins>;
+		interrupt-parent = <&gpio2>;
+		interrupt = <7 IRQ_TYPE_LEVEL_HIGH>;
+		invensense,level-shifter;
+	};
+};
+
+&keypad {
+	pinctrl-names = "default";
+	pinctrl-0 = <&keypad_pins>;
+	keypad,num-rows = <2>;
+	keypad,num-columns = <3>;
+	linux,keymap = <MATRIX_KEY(0, 0, KEY_MENU)
+			MATRIX_KEY(0, 1, KEY_HOME)
+			MATRIX_KEY(0, 2, KEY_BACK)
+			MATRIX_KEY(1, 0, KEY_ESC)
+			MATRIX_KEY(1, 1, KEY_VOLUMEDOWN)
+			MATRIX_KEY(1, 2, KEY_VOLUMEUP)>;
+	linux,input-no-autorepeat;
+};
+
+&mcbsp2 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
+};
+
+
+&mmc1 {
+	/* sdcard */
+	vmmc-supply = <&ldo5>;
+	broken-cd;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	/* emmc */
+	vmmc-supply = <&ldo2>;
+	bus-width = <8>;
+};
+
+&mmc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wl12xx_pins>;
+	vmmc-supply = <&wl12xx_vmmc>;
+	mmc-pwrseq = <&wl12xx_pwrseq>;
+	interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core 0x12e>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1283";
+		reg = <2>;
+		interrupts-extended = <&gpio1 23 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "irq";
+		ref-clock-frequency = <26000000>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
+
+&mmc4 {
+	status = "disabled";
+};
+
+&mmc5 {
+	status = "disabled";
+};
+
+&omap4_pmx_core {
+	bt_pins: pinmux-bt-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE3) /* gpio25 */
+		>;
+	};
+
+	gpio_keys_pins: pinmux-gpio-key-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x56, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio35 */
+		>;
+	};
+
+	i2c1_pins: pinmux-i2c1-pins {
+		pinctrl-single,pins = <
+			   OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
+			   OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
+		>;
+	};
+
+	i2c2_pins: pinmux-i2c2-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x126, PIN_INPUT | MUX_MODE0)	/* i2c2_scl */
+			OMAP4_IOPAD(0x128, PIN_INPUT | MUX_MODE0)	/* i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux-i2c3-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x12a, PIN_INPUT | MUX_MODE0)	/* i2c3_scl */
+			OMAP4_IOPAD(0x12c, PIN_INPUT | MUX_MODE0)	/* i2c3_sda */
+		>;
+	};
+
+	i2c4_pins: pinmux-i2c4-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x12e, PIN_INPUT | MUX_MODE0)	/* i2c4_scl */
+			OMAP4_IOPAD(0x130, PIN_INPUT | MUX_MODE0)	/* i2c4_sda */
+		>;
+	};
+
+	keypad_pins: pinmux-keypad-pins {
+		pinctrl-single,pins = <
+			/* kpd_row0 */
+			OMAP4_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE1)
+			/* kpd_row1 */
+			OMAP4_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE1)
+			/* kpd_row2 */
+			OMAP4_IOPAD(0x0054, PIN_INPUT_PULLUP | MUX_MODE1)
+			/* kpd_col0 */
+			OMAP4_IOPAD(0x0058, PIN_OUTPUT | MUX_MODE1)
+			/* kpd_col1 */
+			OMAP4_IOPAD(0x005a, PIN_OUTPUT | MUX_MODE1)
+			/* kpd_col2 */
+			OMAP4_IOPAD(0x005c, PIN_OUTPUT | MUX_MODE1)
+		>;
+	};
+
+	mcbsp2_pins: pinmux-mcbsp2-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_clkx */
+			OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_dr */
+			OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)      /* abe_mcbsp2_dx */
+			OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_fsx */
+		>;
+	};
+
+	mpu9150_pins: pinmux-mpu9150-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x5e, PIN_INPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	mpu9150h_pins: pinmux-mpu9150h-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x76, PIN_INPUT_PULLUP | MUX_MODE3)
+		>;
+	};
+
+	tlv320aic3x_pins: pinmux-tlv320aic3x-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x7e, PIN_OUTPUT | MUX_MODE3)
+		>;
+	};
+
+	uart2_pins: pinmux-uart2-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */
+			OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0)	 /* uart2_rts.uart2_rts */
+			OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */
+			OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0)	 /* uart2_tx.uart2_tx */
+		>;
+	};
+
+	uart3_pins: pinmux-uart3-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0)  /* uart3_rx_irrx */
+			OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx */
+		>;
+	};
+
+	usb_otg_hs_pins: pinmux-usb-otg-hs-pins {
+		 pinctrl-single,pins = <
+			 OMAP4_IOPAD(0x194, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* usba0_otg_ce */
+			 OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)	     /* usba0_otg_dp */
+			 OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)	     /* usba0_otg_dm */
+		 >;
+	};
+
+	wl12xx_pins: pinmux-wl12xx-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x1c6, PIN_INPUT | MUX_MODE3) /* gpio_23 / IRQ */
+			OMAP4_IOPAD(0x16c, PIN_INPUT_PULLUP | MUX_MODE2) /* sdmmc3_dat2 */
+			OMAP4_IOPAD(0x16e, PIN_INPUT_PULLUP | MUX_MODE2) /* sdmmc3_dat1 */
+			OMAP4_IOPAD(0x170, PIN_INPUT_PULLUP | MUX_MODE2) /* sdmmc3_dat0 */
+			OMAP4_IOPAD(0x172, PIN_INPUT_PULLUP | MUX_MODE2) /* sdmmc3_dat3 */
+			OMAP4_IOPAD(0x174, PIN_INPUT_PULLUP | MUX_MODE2) /* sdmmc3_cmd */
+			OMAP4_IOPAD(0x176, PIN_INPUT_PULLUP | MUX_MODE2) /* sdmmc3_clk */
+		>;
+	};
+
+	wl12xx_gpio: pinmux-wl12xx-gpio-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE3)  /* gpio_24 / WLAN_EN */
+		>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins &bt_pins>;
+	interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core OMAP4_UART2_RX>;
+
+	bluetooth-gnss {
+		compatible = "ti,wl1283-st";
+		enable-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;	/* GPIO_25 */
+		clocks = <&twl 1>;
+		clock-names = "ext_clock";
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core OMAP4_UART3_RX>;
+};
+
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb_otg_hs_pins>;
+
+	interface-type = <1>;
+	mode = <3>;
+	power = <50>;
+};
+
+&usbhshost {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/omap4-kc1.dts b/arch/arm/boot/dts/ti/omap/omap4-kc1.dts
index 31d856b58f8a..c6b79ba8bbc9 100644
--- a/arch/arm/boot/dts/omap4-kc1.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-kc1.dts
@@ -15,16 +15,16 @@
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		green {
+		led-1 {
 			label = "green";
 			pwms = <&twl_pwm 0 7812500>;
 			max-brightness = <127>;
 		};
 
-		orange {
+		led-2 {
 			label = "orange";
 			pwms = <&twl_pwm 1 7812500>;
 			max-brightness = <127>;
@@ -35,42 +35,42 @@
 &omap4_pmx_core {
 	pinctrl-names = "default";
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx */
 			OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
 			OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
 			OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
 			OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x040, PIN_INPUT_PULLUP | MUX_MODE1)	/* sdmmc2_dat0 */
 			OMAP4_IOPAD(0x042, PIN_INPUT_PULLUP | MUX_MODE1)	/* sdmmc2_dat1 */
@@ -85,7 +85,7 @@
 		>;
 	};
 
-	usb_otg_hs_pins: pinmux_usb_otg_hs_pins {
+	usb_otg_hs_pins: usb-otg-hs-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x194, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* usba0_otg_ce */
 			OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)		/* usba0_otg_dp */
diff --git a/arch/arm/boot/dts/omap4-l4-abe.dtsi b/arch/arm/boot/dts/ti/omap/omap4-l4-abe.dtsi
index 6c892fc9d726..59f546a278f8 100644
--- a/arch/arm/boot/dts/omap4-l4-abe.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-l4-abe.dtsi
@@ -1,14 +1,16 @@
 &l4_abe {						/* 0x40100000 */
-	compatible = "ti,omap4-l4-abe", "simple-bus";
+	compatible = "ti,omap4-l4-abe", "simple-pm-bus";
 	reg = <0x40100000 0x400>,
 	      <0x40100400 0x400>;
 	reg-names = "la", "ap";
+	power-domains = <&prm_abe>;
+	/* OMAP4_L4_ABE_CLKCTRL is read-only */
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges = <0x00000000 0x40100000 0x100000>,	/* segment 0 */
 		 <0x49000000 0x49000000 0x100000>;
 	segment@0 {					/* 0x40100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges =
@@ -107,6 +109,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49022000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP1_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -140,6 +144,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49024000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP2_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -173,6 +179,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49026000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP3_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -184,42 +192,43 @@
 		};
 
 		target-module@28000 {			/* 0x40128000, ap 8 08.0 */
+							/* 0x4012a000, ap 10 0a.0 */
 			compatible = "ti,sysc-mcasp", "ti,sysc";
 			reg = <0x28000 0x4>,
 			      <0x28004 0x4>;
 			reg-names = "rev", "sysc";
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>,
-					<SYSC_IDLE_SMART_WKUP>;
+					<SYSC_IDLE_SMART>;
 			/* Domains (V, P, C): iva, abe_pwrdm, abe_clkdm */
 			clocks = <&abe_clkctrl OMAP4_MCASP_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x28000 0x1000>,
-				 <0x49028000 0x49028000 0x1000>;
-
-			/*
-			 * Child device unsupported by davinci-mcasp. At least
-			 * RX path is disabled for omap4, and only DIT mode
-			 * works with no I2S. See also old Android kernel
-			 * omap-mcasp driver for more information.
-			 */
-		};
-
-		target-module@2a000 {			/* 0x4012a000, ap 10 0a.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0x2a000 0x1000>,
+				 <0x49028000 0x49028000 0x1000>,
+				 <0x2000 0x2a000 0x1000>,
 				 <0x4902a000 0x4902a000 0x1000>;
+
+			mcasp0: mcasp@0 {
+				compatible = "ti,omap4-mcasp-audio";
+				reg = <0x0 0x2000>,
+				      <0x4902a000 0x1000>;	/* L3 data port */
+				reg-names = "mpu","dat";
+				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "tx";
+				dmas = <&sdma 8>;
+				dma-names = "tx";
+				clocks = <&abe_clkctrl OMAP4_MCASP_CLKCTRL 0>;
+				clock-names = "fck";
+				op-mode = <1>;	/* MCASP_DIT_MODE */
+				serial-dir = < 1 >; /* 1 TX serializers */
+				status = "disabled";
+			};
 		};
 
 		target-module@2e000 {			/* 0x4012e000, ap 12 0c.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "dmic";
 			reg = <0x2e000 0x4>,
 			      <0x2e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -279,7 +288,6 @@
 
 		mcpdm_module: target-module@32000 {	/* 0x40132000, ap 16 10.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "mcpdm";
 			reg = <0x32000 0x4>,
 			      <0x32010 0x4>;
 			reg-names = "rev", "sysc";
@@ -314,7 +322,6 @@
 
 		target-module@38000 {			/* 0x40138000, ap 18 12.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer5";
 			reg = <0x38000 0x4>,
 			      <0x38010 0x4>;
 			reg-names = "rev", "sysc";
@@ -336,8 +343,9 @@
 				compatible = "ti,omap4430-timer";
 				reg = <0x00000000 0x80>,
 				      <0x49038000 0x80>;
-				clocks = <&abe_clkctrl OMAP4_TIMER5_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP4_TIMER5_CLKCTRL 24>,
+					 <&syc_clk_div_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 			};
@@ -345,7 +353,6 @@
 
 		target-module@3a000 {			/* 0x4013a000, ap 20 14.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer6";
 			reg = <0x3a000 0x4>,
 			      <0x3a010 0x4>;
 			reg-names = "rev", "sysc";
@@ -367,8 +374,9 @@
 				compatible = "ti,omap4430-timer";
 				reg = <0x00000000 0x80>,
 				      <0x4903a000 0x80>;
-				clocks = <&abe_clkctrl OMAP4_TIMER6_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP4_TIMER6_CLKCTRL 24>,
+					 <&syc_clk_div_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 			};
@@ -376,7 +384,6 @@
 
 		target-module@3c000 {			/* 0x4013c000, ap 22 16.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer7";
 			reg = <0x3c000 0x4>,
 			      <0x3c010 0x4>;
 			reg-names = "rev", "sysc";
@@ -398,8 +405,9 @@
 				compatible = "ti,omap4430-timer";
 				reg = <0x00000000 0x80>,
 				      <0x4903c000 0x80>;
-				clocks = <&abe_clkctrl OMAP4_TIMER7_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP4_TIMER7_CLKCTRL 24>,
+					 <&syc_clk_div_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 			};
@@ -407,7 +415,6 @@
 
 		target-module@3e000 {			/* 0x4013e000, ap 24 18.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer8";
 			reg = <0x3e000 0x4>,
 			      <0x3e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -429,8 +436,9 @@
 				compatible = "ti,omap4430-timer";
 				reg = <0x00000000 0x80>,
 				      <0x4903e000 0x80>;
-				clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>,
+					 <&syc_clk_div_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 				ti,timer-dsp;
@@ -466,7 +474,6 @@
 
 		target-module@f1000 {			/* 0x401f1000, ap 32 20.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "aess";
 			reg = <0xf1000 0x4>,
 			      <0xf1010 0x4>;
 			reg-names = "rev", "sysc";
diff --git a/arch/arm/boot/dts/omap4-l4.dtsi b/arch/arm/boot/dts/ti/omap/omap4-l4.dtsi
index 83f803be8ee2..3fcef3080eae 100644
--- a/arch/arm/boot/dts/omap4-l4.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-l4.dtsi
@@ -1,6 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0
 &l4_cfg {						/* 0x4a000000 */
-	compatible = "ti,omap4-l4-cfg", "simple-bus";
+	compatible = "ti,omap4-l4-cfg", "simple-pm-bus";
+	power-domains = <&prm_core>;
+	clocks = <&l4_cfg_clkctrl OMAP4_L4_CFG_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4a000000 0x800>,
 	      <0x4a000800 0x800>,
 	      <0x4a001000 0x1000>;
@@ -16,7 +19,7 @@
 		 <0x00300000 0x4a300000 0x080000>;	/* segment 6 */
 
 	segment@0 {					/* 0x4a000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -43,7 +46,6 @@
 
 		target-module@2000 {			/* 0x4a002000, ap 3 06.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "ctrl_module_core";
 			reg = <0x2000 0x4>,
 			      <0x2010 0x4>;
 			reg-names = "rev", "sysc";
@@ -136,7 +138,6 @@
 
 		target-module@56000 {			/* 0x4a056000, ap 7 0a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "dma_system";
 			reg = <0x56000 0x4>,
 			      <0x5602c 0x4>,
 			      <0x56028 0x4>;
@@ -160,7 +161,7 @@
 			ranges = <0x0 0x56000 0x1000>;
 
 			sdma: dma-controller@0 {
-				compatible = "ti,omap4430-sdma";
+				compatible = "ti,omap4430-sdma", "ti,omap-sdma";
 				reg = <0x0 0x1000>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
@@ -174,7 +175,6 @@
 
 		target-module@58000 {			/* 0x4a058000, ap 10 0e.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "hsi";
 			reg = <0x58000 0x4>,
 			      <0x58010 0x4>,
 			      <0x58014 0x4>;
@@ -242,7 +242,6 @@
 
 		target-module@62000 {			/* 0x4a062000, ap 11 16.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "usb_tll_hs";
 			reg = <0x62000 0x4>,
 			      <0x62010 0x4>,
 			      <0x62014 0x4>;
@@ -270,7 +269,6 @@
 
 		target-module@64000 {			/* 0x4a064000, ap 86 1e.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_host_hs";
 			reg = <0x64000 0x4>,
 			      <0x64010 0x4>,
 			      <0x64014 0x4>;
@@ -321,7 +319,6 @@
 
 		target-module@66000 {			/* 0x4a066000, ap 25 26.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "mmu_dsp";
 			reg = <0x66000 0x4>,
 			      <0x66010 0x4>,
 			      <0x66014 0x4>;
@@ -335,17 +332,24 @@
 			/* Domains (V, P, C): iva, tesla_pwrdm, tesla_clkdm */
 			clocks = <&tesla_clkctrl OMAP4_DSP_CLKCTRL 0>;
 			clock-names = "fck";
+			power-domains = <&prm_tesla>;
+			resets = <&prm_tesla 1>;
+			reset-names = "rstctrl";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x66000 0x1000>;
 
-			/* mmu_dsp cannot be moved before reset driver */
-			status = "disabled";
+			mmu_dsp: mmu@0 {
+				compatible = "ti,omap4-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+			};
 		};
 	};
 
 	segment@80000 {					/* 0x4a080000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00059000 0x000d9000 0x001000>,	/* ap 13 */
@@ -420,7 +424,6 @@
 
 		target-module@2d000 {			/* 0x4a0ad000, ap 88 0c.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "ocp2scp_usb_phy";
 			reg = <0x2d000 0x4>,
 			      <0x2d010 0x4>,
 			      <0x2d014 0x4>;
@@ -499,7 +502,6 @@
 
 		target-module@59000 {			/* 0x4a0d9000, ap 13 1a.0 */
 			compatible = "ti,sysc-omap4-sr", "ti,sysc";
-			ti,hwmods = "smartreflex_mpu";
 			reg = <0x59038 0x4>;
 			reg-names = "sysc";
 			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
@@ -523,7 +525,6 @@
 
 		target-module@5b000 {			/* 0x4a0db000, ap 15 08.0 */
 			compatible = "ti,sysc-omap4-sr", "ti,sysc";
-			ti,hwmods = "smartreflex_iva";
 			reg = <0x5b038 0x4>;
 			reg-names = "sysc";
 			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
@@ -547,7 +548,6 @@
 
 		target-module@5d000 {			/* 0x4a0dd000, ap 17 22.0 */
 			compatible = "ti,sysc-omap4-sr", "ti,sysc";
-			ti,hwmods = "smartreflex_core";
 			reg = <0x5d038 0x4>;
 			reg-names = "sysc";
 			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
@@ -600,11 +600,11 @@
 				#mbox-cells = <1>;
 				ti,mbox-num-users = <3>;
 				ti,mbox-num-fifos = <8>;
-				mbox_ipu: mbox_ipu {
+				mbox_ipu: mbox-ipu {
 					ti,mbox-tx = <0 0 0>;
 					ti,mbox-rx = <1 0 0>;
 				};
-				mbox_dsp: mbox_dsp {
+				mbox_dsp: mbox-dsp {
 					ti,mbox-tx = <3 0 0>;
 					ti,mbox-rx = <2 0 0>;
 				};
@@ -613,7 +613,6 @@
 
 		target-module@76000 {			/* 0x4a0f6000, ap 29 3a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spinlock";
 			reg = <0x76000 0x4>,
 			      <0x76010 0x4>,
 			      <0x76014 0x4>;
@@ -642,7 +641,7 @@
 	};
 
 	segment@100000 {					/* 0x4a100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00100000 0x001000>,	/* ap 21 */
@@ -656,7 +655,6 @@
 
 		target-module@0 {			/* 0x4a100000, ap 21 2a.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "ctrl_module_pad_core";
 			reg = <0x0 0x4>,
 			      <0x10 0x4>;
 			reg-names = "rev", "sysc";
@@ -721,7 +719,6 @@
 
 		target-module@a000 {			/* 0x4a10a000, ap 65 50.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "fdif";
 			reg = <0xa000 0x4>,
 			      <0xa010 0x4>;
 			reg-names = "rev", "sysc";
@@ -745,13 +742,13 @@
 	};
 
 	segment@180000 {					/* 0x4a180000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 
 	segment@200000 {					/* 0x4a200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0001e000 0x0021e000 0x001000>,	/* ap 31 */
@@ -907,13 +904,13 @@
 	};
 
 	segment@280000 {					/* 0x4a280000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 
 	l4_cfg_segment_300000: segment@300000 {			/* 0x4a300000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00300000 0x020000>,	/* ap 67 */
@@ -948,7 +945,10 @@
 };
 
 &l4_wkup {						/* 0x4a300000 */
-	compatible = "ti,omap4-l4-wkup", "simple-bus";
+	compatible = "ti,omap4-l4-wkup", "simple-pm-bus";
+	power-domains = <&prm_wkup>;
+	clocks = <&l4_wkup_clkctrl OMAP4_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4a300000 0x800>,
 	      <0x4a300800 0x800>,
 	      <0x4a301000 0x1000>;
@@ -960,7 +960,7 @@
 		 <0x00020000 0x4a320000 0x010000>;	/* segment 2 */
 
 	segment@0 {					/* 0x4a300000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -977,7 +977,6 @@
 
 		target-module@4000 {			/* 0x4a304000, ap 17 24.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "counter_32k";
 			reg = <0x4000 0x4>,
 			      <0x4004 0x4>;
 			reg-names = "rev", "sysc";
@@ -1046,7 +1045,6 @@
 
 		target-module@c000 {			/* 0x4a30c000, ap 19 2c.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "ctrl_module_wkup";
 			reg = <0xc000 0x4>,
 			      <0xc010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1067,7 +1065,7 @@
 	};
 
 	segment@10000 {					/* 0x4a310000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00010000 0x001000>,	/* ap 5 */
@@ -1142,9 +1140,8 @@
 			};
 		};
 
-		target-module@8000 {			/* 0x4a318000, ap 9 1c.0 */
+		timer1_target: target-module@8000 {	/* 0x4a318000, ap 9 1c.0 */
 			compatible = "ti,sysc-omap2-timer", "ti,sysc";
-			ti,hwmods = "timer1";
 			reg = <0x8000 0x4>,
 			      <0x8010 0x4>,
 			      <0x8014 0x4>;
@@ -1168,8 +1165,9 @@
 			timer1: timer@0 {
 				compatible = "ti,omap3430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_wkup_clkctrl OMAP4_TIMER1_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_wkup_clkctrl OMAP4_TIMER1_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-alwon;
 			};
@@ -1177,7 +1175,6 @@
 
 		target-module@c000 {			/* 0x4a31c000, ap 11 20.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "kbd";
 			reg = <0xc000 0x4>,
 			      <0xc010 0x4>,
 			      <0xc014 0x4>;
@@ -1208,7 +1205,6 @@
 
 		target-module@e000 {			/* 0x4a31e000, ap 21 30.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "ctrl_module_pad_wkup";
 			reg = <0xe000 0x4>,
 			      <0xe010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1237,7 +1233,7 @@
 	};
 
 	segment@20000 {					/* 0x4a320000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00006000 0x00026000 0x001000>,	/* ap 13 */
@@ -1290,7 +1286,10 @@
 };
 
 &l4_per {						/* 0x48000000 */
-	compatible = "ti,omap4-l4-per", "simple-bus";
+	compatible = "ti,omap4-l4-per", "simple-pm-bus";
+	power-domains = <&prm_l4per>;
+	clocks = <&l4_per_clkctrl OMAP4_L4_PER_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48000000 0x800>,
 	      <0x48000800 0x800>,
 	      <0x48001000 0x400>,
@@ -1304,7 +1303,7 @@
 		 <0x00200000 0x48200000 0x200000>;	/* segment 1 */
 
 	segment@0 {					/* 0x48000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -1422,7 +1421,6 @@
 
 		target-module@32000 {			/* 0x48032000, ap 5 02.0 */
 			compatible = "ti,sysc-omap2-timer", "ti,sysc";
-			ti,hwmods = "timer2";
 			reg = <0x32000 0x4>,
 			      <0x32010 0x4>,
 			      <0x32014 0x4>;
@@ -1446,15 +1444,15 @@
 			timer2: timer@0 {
 				compatible = "ti,omap3430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_per_clkctrl OMAP4_TIMER2_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_per_clkctrl OMAP4_TIMER2_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@34000 {			/* 0x48034000, ap 7 04.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer3";
 			reg = <0x34000 0x4>,
 			      <0x34010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1474,15 +1472,15 @@
 			timer3: timer@0 {
 				compatible = "ti,omap4430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_per_clkctrl OMAP4_TIMER3_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_per_clkctrl OMAP4_TIMER3_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@36000 {			/* 0x48036000, ap 9 0e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer4";
 			reg = <0x36000 0x4>,
 			      <0x36010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1502,15 +1500,15 @@
 			timer4: timer@0 {
 				compatible = "ti,omap4430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_per_clkctrl OMAP4_TIMER4_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_per_clkctrl OMAP4_TIMER4_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@3e000 {			/* 0x4803e000, ap 11 08.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer9";
 			reg = <0x3e000 0x4>,
 			      <0x3e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1530,13 +1528,15 @@
 			timer9: timer@0 {
 				compatible = "ti,omap4430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 			};
 		};
 
+		/* Unused DSS L4 access, see L3 instead */
 		target-module@40000 {			/* 0x48040000, ap 13 0a.0 */
 			compatible = "ti,sysc";
 			status = "disabled";
@@ -1892,7 +1892,6 @@
 
 		target-module@76000 {			/* 0x48076000, ap 39 38.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "slimbus2";
 			reg = <0x76000 0x4>,
 			      <0x76010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1913,7 +1912,6 @@
 
 		target-module@78000 {			/* 0x48078000, ap 41 1a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "elm";
 			reg = <0x78000 0x4>,
 			      <0x78010 0x4>,
 			      <0x78014 0x4>;
@@ -1942,7 +1940,6 @@
 
 		target-module@86000 {			/* 0x48086000, ap 43 24.0 */
 			compatible = "ti,sysc-omap2-timer", "ti,sysc";
-			ti,hwmods = "timer10";
 			reg = <0x86000 0x4>,
 			      <0x86010 0x4>,
 			      <0x86014 0x4>;
@@ -1966,8 +1963,9 @@
 			timer10: timer@0 {
 				compatible = "ti,omap3430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_per_clkctrl OMAP4_TIMER10_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_per_clkctrl OMAP4_TIMER10_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 			};
@@ -1975,7 +1973,6 @@
 
 		target-module@88000 {			/* 0x48088000, ap 45 2e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer11";
 			reg = <0x88000 0x4>,
 			      <0x88010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1995,19 +1992,34 @@
 			timer11: timer@0 {
 				compatible = "ti,omap4430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4_per_clkctrl OMAP4_TIMER11_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4_per_clkctrl OMAP4_TIMER11_CLKCTRL 24>,
+					 <&sys_clkin_ck>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 			};
 		};
 
-		target-module@90000 {			/* 0x48090000, ap 57 2a.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+		rng_target: target-module@90000 {	/* 0x48090000, ap 57 2a.0 */
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x91fe0 0x4>,
+			      <0x91fe4 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>;
+			/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+			clocks = <&l4_secure_clkctrl OMAP4_RNG_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x90000 0x2000>;
+
+			rng: rng@0 {
+				compatible = "ti,omap4-rng";
+				reg = <0x0 0x2000>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			};
 		};
 
 		target-module@96000 {			/* 0x48096000, ap 37 26.0 */
@@ -2031,6 +2043,8 @@
 				compatible = "ti,omap4-mcbsp";
 				reg = <0x0 0xff>; /* L4 Interconnect */
 				reg-names = "mpu";
+				clocks = <&l4_per_clkctrl OMAP4_MCBSP4_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -2171,6 +2185,35 @@
 				 <0x00001000 0x000a5000 0x00001000>;
 		};
 
+		des_target: target-module@a5000 {	/* 0x480a5000 */
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0xa5030 0x4>,
+			      <0xa5034 0x4>,
+			      <0xa5038 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+			clocks = <&l4_secure_clkctrl OMAP4_DES3DES_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xa5000 0x00001000>;
+
+			des: des@0 {
+				compatible = "ti,omap4-des";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 117>, <&sdma 116>;
+				dma-names = "tx", "rx";
+			};
+		};
+
 		target-module@a8000 {			/* 0x480a8000, ap 61 3e.0 */
 			compatible = "ti,sysc";
 			status = "disabled";
@@ -2401,7 +2444,7 @@
 	};
 
 	segment@200000 {					/* 0x48200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00150000 0x00350000 0x001000>,	/* ap 77 */
diff --git a/arch/arm/boot/dts/omap4-mcpdm.dtsi b/arch/arm/boot/dts/ti/omap/omap4-mcpdm.dtsi
index 915a9b31a33b..03ade47431fb 100644
--- a/arch/arm/boot/dts/omap4-mcpdm.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-mcpdm.dtsi
@@ -7,7 +7,7 @@
  */
 
 &omap4_pmx_core {
-	mcpdm_pins: pinmux_mcpdm_pins {
+	mcpdm_pins: mcpdm-pins {
 		pinctrl-single,pins = <
 		/* 0x4a100106 abe_pdm_ul_data.abe_pdm_ul_data ag25 */
 		OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0)
diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/ti/omap/omap4-panda-a4.dts
index 64083075dd52..8fd076e5d1b0 100644
--- a/arch/arm/boot/dts/omap4-panda-a4.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-panda-a4.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi
index 55ea8b6189af..f528511c2537 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include <dt-bindings/input/input.h>
 #include "elpida_ecb240abacn.dtsi"
@@ -12,6 +12,26 @@
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dsp_memory_region: dsp-memory@98000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x98000000 0x800000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu_memory_region: ipu-memory@98800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x98800000 0x7000000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	chosen {
 		stdout-path = &uart3;
 	};
@@ -29,13 +49,13 @@
 			&led_wkgpio_pins
 		>;
 
-		heartbeat {
+		led-heartbeat {
 			label = "pandaboard::status1";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		mmc {
+		led-mmc {
 			label = "pandaboard::status2";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
@@ -217,14 +237,14 @@
 			&hsusbb1_pins
 	>;
 
-	twl6040_pins: pinmux_twl6040_pins {
+	twl6040_pins: twl6040-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3)	/* hdq_sio.gpio_127 */
 			OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0)	/* sys_nirq2.sys_nirq2 */
 		>;
 	};
 
-	mcbsp1_pins: pinmux_mcbsp1_pins {
+	mcbsp1_pins: mcbsp1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
 			OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dr.abe_mcbsp1_dr */
@@ -233,7 +253,7 @@
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5)	/* dispc2_data23 */
 			OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) 	/* dispc2_data22 */
@@ -268,13 +288,13 @@
 		>;
 	};
 
-	tfp410_pins: pinmux_tfp410_pins {
+	tfp410_pins: tfp410-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3)	/* gpio_0 */
 		>;
 	};
 
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)		/* hdmi_cec.hdmi_cec */
 			OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_scl.hdmi_scl */
@@ -282,7 +302,7 @@
 		>;
 	};
 
-	tpd12s015_pins: pinmux_tpd12s015_pins {
+	tpd12s015_pins: tpd12s015-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a17.gpio_41 */
 			OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)		/* gpmc_nbe1.gpio_60 */
@@ -290,7 +310,7 @@
 		>;
 	};
 
-	hsusbb1_pins: pinmux_hsusbb1_pins {
+	hsusbb1_pins: hsusbb1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
 			OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4)		/* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
@@ -307,28 +327,28 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
 			OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
 			OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
 			OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
@@ -339,7 +359,7 @@
 	 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
 	 * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
 	 */
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
 			OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a22.gpio_46 */
@@ -349,7 +369,7 @@
 	};
 
 	/* wl12xx GPIO inputs and SDIO pins */
-	wl12xx_pins: pinmux_wl12xx_pins {
+	wl12xx_pins: wl12xx-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)		/* gpmc_ncs2.gpio_52 */
 			OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
@@ -362,7 +382,7 @@
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpio_121 */
 		>;
@@ -370,7 +390,7 @@
 };
 
 &omap4_pmx_wkup {
-	led_wkgpio_pins: pinmux_leds_wkpins {
+	led_wkgpio_pins: leds-wkpins-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3)	/* gpio_wk7 */
 			OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3)	/* gpio_wk8 */
@@ -538,7 +558,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
@@ -546,7 +566,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	port {
 		dpi_out: endpoint {
@@ -557,12 +577,12 @@
 };
 
 &dsi2 {
-	status = "ok";
+	status = "okay";
 	vdd-supply = <&vcxio>;
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 	vdda-supply = <&vdac>;
 
 	port {
@@ -571,3 +591,17 @@
 		};
 	};
 };
+
+&dsp {
+	status = "okay";
+	memory-region = <&dsp_memory_region>;
+	ti,timers = <&timer5>;
+	ti,watchdog-timers = <&timer6>;
+};
+
+&ipu {
+	status = "okay";
+	memory-region = <&ipu_memory_region>;
+	ti,timers = <&timer3>;
+	ti,watchdog-timers = <&timer9>, <&timer11>;
+};
diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/ti/omap/omap4-panda-es.dts
index 9dd307b52604..fe7b156d10ed 100644
--- a/arch/arm/boot/dts/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-panda-es.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -38,15 +38,31 @@
 };
 
 &omap4_pmx_core {
-	led_gpio_pins: gpio_led_pmx {
+	led_gpio_pins: gpio-led-pmx-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0f6, PIN_OUTPUT | MUX_MODE3)	/* gpio_110 */
 		>;
 	};
 
-	button_pins: pinmux_button_pins {
+	button_pins: button-pins {
 		pinctrl-single,pins = <
-			OMAP4_IOPAD(0x11b, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_113 */
+			OMAP4_IOPAD(0x0fc, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_113 */
+		>;
+	};
+
+	bt_pins: bt-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a22.gpio_46 - BTEN */
+			OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a25.gpio_49 - BTWAKEUP */
+		>;
+	};
+
+	uart2_pins: uart2-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts - HCI */
+			OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
+			OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_rx.uart2_rx */
+			OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
 		>;
 	};
 };
@@ -63,10 +79,10 @@
 		&led_wkgpio_pins
 	>;
 
-	heartbeat {
+	led-heartbeat {
 		gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
 	};
-	mmc {
+	led-mmc {
 		gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
 };
@@ -80,3 +96,19 @@
 &gpio1_target {
 	 ti,no-reset-on-init;
 };
+
+&wl12xx_gpio {
+	pinctrl-single,pins = <
+		OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
+		OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a24.gpio_48 */
+	>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins &bt_pins>;
+	bluetooth: tiwi {
+		compatible = "ti,wl1271-st";
+		enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>;	/* GPIO_46 */
+	};
+};
diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/ti/omap/omap4-panda.dts
index fb2f47717b45..529d5bcceaaf 100644
--- a/arch/arm/boot/dts/omap4-panda.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-panda.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/omap4-sdp-es23plus.dts b/arch/arm/boot/dts/ti/omap/omap4-sdp-es23plus.dts
index 42154520d383..869f6279b5be 100644
--- a/arch/arm/boot/dts/omap4-sdp-es23plus.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-sdp-es23plus.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include "omap4-sdp.dts"
 
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/ti/omap/omap4-sdp.dts
index 91480ac1f328..b2cb93edbc3a 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-sdp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -45,58 +45,60 @@
 		regulator-boot-on;
 	};
 
-	leds {
+	led-controller-1 {
 		compatible = "gpio-leds";
-		debug0 {
+
+		led-1 {
 			label = "omap4:green:debug0";
 			gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; /* 61 */
 		};
 
-		debug1 {
+		led-2 {
 			label = "omap4:green:debug1";
 			gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>; /* 30 */
 		};
 
-		debug2 {
+		led-3 {
 			label = "omap4:green:debug2";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; /* 7 */
 		};
 
-		debug3 {
+		led-4 {
 			label = "omap4:green:debug3";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* 8 */
 		};
 
-		debug4 {
+		led-5 {
 			label = "omap4:green:debug4";
 			gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; /* 50 */
 		};
 
-		user1 {
+		led-6 {
 			label = "omap4:blue:user";
 			gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* 169 */
 		};
 
-		user2 {
+		led-7 {
 			label = "omap4:red:user";
 			gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>; /* 170 */
 		};
 
-		user3 {
+		led-8 {
 			label = "omap4:green:user";
 			gpios = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* 139 */
 		};
 	};
 
-	pwmleds {
+	led-controller-2 {
 		compatible = "pwm-leds";
-		kpad {
+
+		led-9 {
 			label = "omap4::keypad";
 			pwms = <&twl_pwm 0 7812500>;
 			max-brightness = <127>;
 		};
 
-		charging {
+		led-10 {
 			label = "omap4:green:chrg";
 			pwms = <&twl_pwmled 0 7812500>;
 			max-brightness = <255>;
@@ -212,7 +214,7 @@
 			&tpd12s015_pins
 	>;
 
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
 			OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
@@ -221,7 +223,7 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
 			OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
@@ -230,21 +232,21 @@
 		>;
 	};
 
-	uart4_pins: pinmux_uart4_pins {
+	uart4_pins: uart4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)		/* uart4_rx.uart4_rx */
 			OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)		/* uart4_tx.uart4_tx */
 		>;
 	};
 
-	twl6040_pins: pinmux_twl6040_pins {
+	twl6040_pins: twl6040-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3)		/* hdq_sio.gpio_127 */
 			OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0)		/* sys_nirq2.sys_nirq2 */
 		>;
 	};
 
-	dmic_pins: pinmux_dmic_pins {
+	dmic_pins: dmic-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x110, PIN_OUTPUT | MUX_MODE0)		/* abe_dmic_clk1.abe_dmic_clk1 */
 			OMAP4_IOPAD(0x112, PIN_INPUT | MUX_MODE0)		/* abe_dmic_din1.abe_dmic_din1 */
@@ -253,7 +255,7 @@
 		>;
 	};
 
-	mcbsp1_pins: pinmux_mcbsp1_pins {
+	mcbsp1_pins: mcbsp1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
 			OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dr.abe_mcbsp1_dr */
@@ -262,7 +264,7 @@
 		>;
 	};
 
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)		/* abe_mcbsp2_clkx.abe_mcbsp2_clkx */
 			OMAP4_IOPAD(0x0f8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp2_dr.abe_mcbsp2_dr */
@@ -271,7 +273,7 @@
 		>;
 	};
 
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x132, PIN_INPUT | MUX_MODE0)		/*  mcspi1_clk.mcspi1_clk */
 			OMAP4_IOPAD(0x134, PIN_INPUT | MUX_MODE0)		/*  mcspi1_somi.mcspi1_somi */
@@ -280,7 +282,7 @@
 		>;
 	};
 
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)		/* hdmi_cec.hdmi_cec */
 			OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_scl.hdmi_scl */
@@ -288,7 +290,7 @@
 		>;
 	};
 
-	tpd12s015_pins: pinmux_tpd12s015_pins {
+	tpd12s015_pins: tpd12s015-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a17.gpio_41 */
 			OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)		/* gpmc_nbe1.gpio_60 */
@@ -296,28 +298,28 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
 			OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
 			OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
 			OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
@@ -325,14 +327,14 @@
 	};
 
 	/* wl12xx GPIO output for WLAN_EN */
-	wl12xx_gpio: pinmux_wl12xx_gpio {
+	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)		/* gpmc_nwp.gpio_54 */
 		>;
 	};
 
 	/* wl12xx GPIO inputs and SDIO pins */
-	wl12xx_pins: pinmux_wl12xx_pins {
+	wl12xx_pins: wl12xx-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
 			OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk.sdmmc5_clk */
@@ -345,13 +347,13 @@
 	};
 
 	/* gpio_48 for ENET_ENABLE */
-	enet_enable_gpio: pinmux_enet_enable_gpio {
+	enet_enable_gpio: enet-enable-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* gpmc_a24.gpio_48 */
 		>;
 	};
 
-	ks8851_pins: pinmux_ks8851_pins {
+	ks8851_pins: ks8851-pins {
 		pinctrl-single,pins = <
 			/* ENET_INT */
 			OMAP4_IOPAD(0x054, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ad10.gpio_34 */
@@ -428,7 +430,7 @@
 
 	/*
 	 * Temperature Sensor
-	 * http://www.ti.com/lit/ds/symlink/tmp105.pdf
+	 * https://www.ti.com/lit/ds/symlink/tmp105.pdf
 	 */
 	tmp105@48 {
 		compatible = "ti,tmp105";
@@ -453,7 +455,7 @@
 
 	/*
 	 * 3-Axis Digital Compass
-	 * http://www.sparkfun.com/datasheets/Sensors/Magneto/HMC5843.pdf
+	 * https://www.sparkfun.com/datasheets/Sensors/Magneto/HMC5843.pdf
 	 */
 	hmc5843@1e {
 		compatible = "honeywell,hmc5843";
@@ -648,11 +650,11 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 };
 
 &dsi1 {
-	status = "ok";
+	status = "okay";
 	vdd-supply = <&vcxio>;
 
 	port {
@@ -662,8 +664,9 @@
 		};
 	};
 
-	lcd0: display {
+	lcd0: panel@0 {
 		compatible = "tpo,taal", "panel-dsi-cm";
+		reg = <0>;
 		label = "lcd0";
 
 		reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;	/* 102 */
@@ -677,7 +680,7 @@
 };
 
 &dsi2 {
-	status = "ok";
+	status = "okay";
 	vdd-supply = <&vcxio>;
 
 	port {
@@ -687,8 +690,9 @@
 		};
 	};
 
-	lcd1: display {
+	lcd1: panel@0 {
 		compatible = "tpo,taal", "panel-dsi-cm";
+		reg = <0>;
 		label = "lcd1";
 
 		reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;	/* 104 */
@@ -702,7 +706,7 @@
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 	vdda-supply = <&vdac>;
 
 	port {
diff --git a/arch/arm/boot/dts/omap4-var-dvk-om44.dts b/arch/arm/boot/dts/ti/omap/omap4-var-dvk-om44.dts
index 84fd17fb0822..84fd17fb0822 100644
--- a/arch/arm/boot/dts/omap4-var-dvk-om44.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-var-dvk-om44.dts
diff --git a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi b/arch/arm/boot/dts/ti/omap/omap4-var-om44customboard.dtsi
index 458cb53dd3d1..cadc7e02592b 100644
--- a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-var-om44customboard.dtsi
@@ -60,7 +60,7 @@
 };
 
 &omap4_pmx_core {
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)	/* mcspi1_cs2.uart1_cts */
 			OMAP4_IOPAD(0x13e, PIN_OUTPUT | MUX_MODE1)		/* mcspi1_cs3.uart1_rts */
@@ -69,7 +69,7 @@
 		>;
 	};
 
-	mcspi1_pins: pinmux_mcspi1_pins {
+	mcspi1_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x132, PIN_INPUT | MUX_MODE0)		/*  mcspi1_clk.mcspi1_clk */
 			OMAP4_IOPAD(0x134, PIN_INPUT | MUX_MODE0)		/*  mcspi1_somi.mcspi1_somi */
@@ -78,13 +78,13 @@
 		>;
 	};
 
-	mcasp_pins: pinmux_mcsasp_pins {
+	mcasp_pins: mcsasp-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0f8, PIN_OUTPUT | MUX_MODE2)		/*  mcbsp2_dr.abe_mcasp_axr */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5)		/* dispc2_data23 */
 			OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5)		/* dispc2_data22 */
@@ -117,7 +117,7 @@
 		>;
 	};
 
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)		/* hdmi_cec.hdmi_cec */
 			OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_scl.hdmi_scl */
@@ -125,14 +125,14 @@
 		>;
 	};
 
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
 			OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
 
-	mmc5_pins: pinmux_mmc5_pins {
+	mmc5_pins: mmc5-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE3)		/* abe_mcbsp2_clkx.gpio_110 */
 			OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk.sdmmc5_clk */
@@ -144,32 +144,32 @@
 		>;
 	};
 
-	gpio_led_pins: pinmux_gpio_led_pins {
+	gpio_led_pins: gpio-led-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x17e, PIN_OUTPUT | MUX_MODE3)		/* kpd_col4.gpio_172 */
 			OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)		/* kpd_col5.gpio_173 */
 		>;
 	};
 
-	gpio_key_pins: pinmux_gpio_key_pins {
+	gpio_key_pins: gpio-key-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x1a2, PIN_INPUT | MUX_MODE3)		/* sys_boot0.gpio_184 */
 		>;
 	};
 
-	ks8851_irq_pins: pinmux_ks8851_irq_pins {
+	ks8851_irq_pins: ks8851-irq-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x17c, PIN_INPUT_PULLUP | MUX_MODE3)	/* kpd_col3.gpio_171 */
 		>;
 	};
 
-	hdmi_hpd_pins: pinmux_hdmi_hpd_pins {
+	hdmi_hpd_pins: hdmi-hpd-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* hdmi_hpd.gpio_63 */
 		>;
 	};
 
-	backlight_pins: pinmux_backlight_pins {
+	backlight_pins: backlight-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x116, PIN_OUTPUT | MUX_MODE3)		/* abe_dmic_din3.gpio_122 */
 		>;
diff --git a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi b/arch/arm/boot/dts/ti/omap/omap4-var-som-om44-wlan.dtsi
index d0032213101e..de779d2d7c3e 100644
--- a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-var-som-om44-wlan.dtsi
@@ -19,7 +19,7 @@
 };
 
 &omap4_pmx_core {
-	uart2_pins: pinmux_uart2_pins {
+	uart2_pins: uart2-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
 			OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
@@ -28,7 +28,7 @@
 		>;
 	};
 
-	wl12xx_ctrl_pins: pinmux_wl12xx_ctrl_pins {
+	wl12xx_ctrl_pins: wl12xx-ctrl-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x062, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a17.gpio_41 (WLAN_IRQ) */
 			OMAP4_IOPAD(0x064, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a18.gpio_42 (BT_EN) */
@@ -36,7 +36,7 @@
 		>;
 	};
 
-	mmc4_pins: pinmux_mmc4_pins {
+	mmc4_pins: mmc4-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x154, PIN_INPUT_PULLUP | MUX_MODE1)	/* mcspi4_clk.sdmmc4_clk */
 			OMAP4_IOPAD(0x156, PIN_INPUT_PULLUP | MUX_MODE1)	/* mcspi4_simo.sdmmc4_cmd */
diff --git a/arch/arm/boot/dts/omap4-var-som-om44.dtsi b/arch/arm/boot/dts/ti/omap/omap4-var-som-om44.dtsi
index 41de32bcf187..37d56b3010cf 100644
--- a/arch/arm/boot/dts/omap4-var-som-om44.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-var-som-om44.dtsi
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Joachim Eastwood <manabian@gmail.com>
- * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com
+ * Copyright (C) 2012 Variscite Ltd. - https://www.variscite.com
  */
 #include "omap4460.dtsi"
 #include "omap4-mcpdm.dtsi"
@@ -65,21 +65,21 @@
 			&hsusbb1_pins
 	>;
 
-	twl6040_pins: pinmux_twl6040_pins {
+	twl6040_pins: twl6040-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x19c, PIN_OUTPUT | MUX_MODE3)		/* fref_clk2_out.gpio_182 */
 			OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0)		/* sys_nirq2.sys_nirq2 */
 		>;
 	};
 
-	tsc2004_pins: pinmux_tsc2004_pins {
+	tsc2004_pins: tsc2004-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x090, PIN_INPUT | MUX_MODE3)		/* gpmc_ncs4.gpio_101 (irq) */
 			OMAP4_IOPAD(0x092, PIN_OUTPUT | MUX_MODE3)		/* gpmc_ncs5.gpio_102 (rst) */
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
 			OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
@@ -88,7 +88,7 @@
 		>;
 	};
 
-	hsusbb1_pins: pinmux_hsusbb1_pins {
+	hsusbb1_pins: hsusbb1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
 			OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4)		/* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
@@ -105,27 +105,27 @@
 		>;
 	};
 
-	hsusbb1_phy_rst_pins: pinmux_hsusbb1_phy_rst_pins {
+	hsusbb1_phy_rst_pins: hsusbb1-phy-rst-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x18c, PIN_OUTPUT | MUX_MODE3)		/* kpd_row2.gpio_177 */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	i2c3_pins: pinmux_i2c3_pins {
+	i2c3_pins: i2c3-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
 			OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
 			OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
@@ -144,19 +144,19 @@
 		&lan7500_rst_pins
 	>;
 
-	hsusbb1_phy_clk_pins: pinmux_hsusbb1_phy_clk_pins {
+	hsusbb1_phy_clk_pins: hsusbb1-phy-clk-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x058, PIN_OUTPUT | MUX_MODE0)	/* fref_clk3_out */
 		>;
 	};
 
-	hsusbb1_hub_rst_pins: pinmux_hsusbb1_hub_rst_pins {
+	hsusbb1_hub_rst_pins: hsusbb1-hub-rst-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x042, PIN_OUTPUT | MUX_MODE3)	/* gpio_wk1 */
 		>;
 	};
 
-	lan7500_rst_pins: pinmux_lan7500_rst_pins {
+	lan7500_rst_pins: lan7500-rst-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x040, PIN_OUTPUT | MUX_MODE3)	/* gpio_wk0 */
 		>;
diff --git a/arch/arm/boot/dts/omap4-var-stk-om44.dts b/arch/arm/boot/dts/ti/omap/omap4-var-stk-om44.dts
index 656fb29c2a15..656fb29c2a15 100644
--- a/arch/arm/boot/dts/omap4-var-stk-om44.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-var-stk-om44.dts
diff --git a/arch/arm/boot/dts/ti/omap/omap4-xyboard-mz609.dts b/arch/arm/boot/dts/ti/omap/omap4-xyboard-mz609.dts
new file mode 100644
index 000000000000..762934e2d075
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-xyboard-mz609.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-mz607-mz617.dtsi"
+
+/ {
+	model = "Motorola Xyboard MZ609";
+	compatible = "motorola,xyboard-mz609", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display1 = &hdmi0;
+	};
+
+	backlight: backlight {
+		compatible = "led-backlight";
+
+		leds = <&backlight_led>;
+		brightness-levels = <31 63 95 127 159 191 223 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&i2c1 {
+	led-controller@38 {
+		compatible = "ti,lm3532";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x38>;
+
+		enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+
+		ramp-up-us = <1024>;
+		ramp-down-us = <8193>;
+
+		backlight_led: led@0 {
+			reg = <0>;
+			led-sources = <2>;
+			ti,led-mode = <0>;
+			label = ":backlight";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/omap4-xyboard-mz617.dts b/arch/arm/boot/dts/ti/omap/omap4-xyboard-mz617.dts
new file mode 100644
index 000000000000..b9caea3b7f9d
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4-xyboard-mz617.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-mz607-mz617.dtsi"
+
+/ {
+	model = "Motorola Xyboard MZ617";
+	compatible = "motorola,xyboard-mz617", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display1 = &hdmi0;
+	};
+};
diff --git a/arch/arm/boot/dts/ti/omap/omap4.dtsi b/arch/arm/boot/dts/ti/omap/omap4.dtsi
new file mode 100644
index 000000000000..2bbff9032be3
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap4.dtsi
@@ -0,0 +1,868 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/clock/omap4.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/omap.h>
+#include <dt-bindings/clock/omap4.h>
+
+/ {
+	compatible = "ti,omap4430", "ti,omap4";
+	interrupt-parent = <&wakeupgen>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		mmc0 = &mmc1;
+		mmc1 = &mmc2;
+		mmc2 = &mmc3;
+		mmc3 = &mmc4;
+		mmc4 = &mmc5;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		rproc0 = &dsp;
+		rproc1 = &ipu;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+		};
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+			reg = <0x1>;
+		};
+	};
+
+	/*
+	 * Needed early by omap4_sram_init() for barrier, do not move to l3
+	 * interconnect as simple-pm-bus probes at module_init() time.
+	 */
+	ocmcram: sram@40304000 {
+		compatible = "mmio-sram";
+		reg = <0x40304000 0xa000>; /* 40k */
+	};
+
+	gic: interrupt-controller@48241000 {
+		compatible = "arm,cortex-a9-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48241000 0x1000>,
+		      <0x48240100 0x0100>;
+		interrupt-parent = <&gic>;
+	};
+
+	L2: cache-controller@48242000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x48242000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	local-timer@48240600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		clocks = <&mpu_periphclk>;
+		reg = <0x48240600 0x20>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>;
+		interrupt-parent = <&gic>;
+	};
+
+	wakeupgen: interrupt-controller@48281000 {
+		compatible = "ti,omap4-wugen-mpu";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48281000 0x1000>;
+		interrupt-parent = <&gic>;
+	};
+
+	/*
+	 * XXX: Use a flat representation of the OMAP4 interconnect.
+	 * The real OMAP interconnect network is quite complex.
+	 * Since it will not bring real advantage to represent that in DT for
+	 * the moment, just use a fake OCP bus entry to represent the whole bus
+	 * hierarchy.
+	 */
+	ocp {
+		compatible = "simple-pm-bus";
+		power-domains = <&prm_l4per>;
+		clocks = <&l3_1_clkctrl OMAP4_L3_MAIN_1_CLKCTRL 0>,
+			 <&l3_2_clkctrl OMAP4_L3_MAIN_2_CLKCTRL 0>,
+			 <&l3_instr_clkctrl OMAP4_L3_MAIN_3_CLKCTRL 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		l3-noc@44000000 {
+			compatible = "ti,omap4-l3-noc";
+			reg = <0x44000000 0x1000>,
+			      <0x44800000 0x2000>,
+			      <0x45000000 0x1000>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		l4_wkup: interconnect@4a300000 {
+		};
+
+		l4_cfg: interconnect@4a000000 {
+		};
+
+		l4_per: interconnect@48000000 {
+		};
+
+		target-module@48210000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			power-domains = <&prm_mpu>;
+			clocks = <&mpuss_clkctrl OMAP4_MPU_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48210000 0x1f0000>;
+
+			mpu {
+				compatible = "ti,omap4-mpu";
+				sram = <&ocmcram>;
+			};
+		};
+
+		l4_abe: interconnect@40100000 {
+		};
+
+		target-module@50000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x50000000 4>,
+			      <0x50000010 4>,
+			      <0x50000014 4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			ti,no-idle-on-init;
+			clocks = <&l3_2_clkctrl OMAP4_GPMC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
+				 <0x00000000 0x00000000 0x40000000>; /* data */
+
+			gpmc: gpmc@50000000 {
+				compatible = "ti,omap4430-gpmc";
+				reg = <0x50000000 0x1000>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 4>;
+				dma-names = "rxtx";
+				gpmc,num-cs = <8>;
+				gpmc,num-waitpins = <4>;
+				clocks = <&l3_div_ck>;
+				clock-names = "fck";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		target-module@52000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x52000000 0x4>,
+			      <0x52000010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-delay-us = <2>;
+			power-domains = <&prm_cam>;
+			clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x52000000 0x1000000>;
+
+			/* No child device binding, driver in staging */
+		};
+
+		/*
+		 * Note that 4430 needs cross trigger interface (CTI) supported
+		 * before we can configure the interrupts. This means sampling
+		 * events are not supported for pmu. Note that 4460 does not use
+		 * CTI, see also 4460.dtsi.
+		 */
+		target-module@54000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			power-domains = <&prm_emu>;
+			clocks = <&emu_sys_clkctrl OMAP4_DEBUGSS_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x54000000 0x1000000>;
+
+			pmu: pmu {
+				compatible = "arm,cortex-a9-pmu";
+			};
+		};
+
+		target-module@55082000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x55082000 0x4>,
+			      <0x55082010 0x4>,
+			      <0x55082014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_core 2>;
+			reset-names = "rstctrl";
+			ranges = <0x0 0x55082000 0x100>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			mmu_ipu: mmu@0 {
+				compatible = "ti,omap4-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,iommu-bus-err-back;
+			};
+		};
+
+		target-module@4012c000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x4012c000 0x4>,
+			      <0x4012c010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			clocks = <&abe_clkctrl OMAP4_SLIMBUS1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */
+				 <0x4902c000 0x4902c000 0x1000>; /* L3 */
+
+			/* No child device binding or driver in mainline */
+		};
+
+		target-module@4e000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4e000000 0x4>,
+			      <0x4e000010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ranges = <0x0 0x4e000000 0x2000000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			dmm@0 {
+				compatible = "ti,omap4-dmm";
+				reg = <0 0x800>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		target-module@4c000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			reg = <0x4c000000 0x4>;
+			reg-names = "rev";
+			clocks = <&l3_emif_clkctrl OMAP4_EMIF1_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4c000000 0x1000000>;
+
+			emif1: emif@0 {
+				compatible = "ti,emif-4d";
+				reg = <0 0x100>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phy-type = <1>;
+				hw-caps-read-idle-ctrl;
+				hw-caps-ll-interface;
+				hw-caps-temp-alert;
+			};
+		};
+
+		target-module@4d000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			reg = <0x4d000000 0x4>;
+			reg-names = "rev";
+			clocks = <&l3_emif_clkctrl OMAP4_EMIF2_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4d000000 0x1000000>;
+
+			emif2: emif@0 {
+				compatible = "ti,emif-4d";
+				reg = <0 0x100>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				phy-type = <1>;
+				hw-caps-read-idle-ctrl;
+				hw-caps-ll-interface;
+				hw-caps-temp-alert;
+			};
+		};
+
+		dsp: dsp {
+			compatible = "ti,omap4-dsp";
+			ti,bootreg = <&scm_conf 0x304 0>;
+			iommus = <&mmu_dsp>;
+			resets = <&prm_tesla 0>;
+			clocks = <&tesla_clkctrl OMAP4_DSP_CLKCTRL 0>;
+			firmware-name = "omap4-dsp-fw.xe64T";
+			mboxes = <&mailbox &mbox_dsp>;
+			status = "disabled";
+		};
+
+		ipu: ipu@55020000 {
+			compatible = "ti,omap4-ipu";
+			reg = <0x55020000 0x10000>;
+			reg-names = "l2ram";
+			iommus = <&mmu_ipu>;
+			resets = <&prm_core 0>, <&prm_core 1>;
+			clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>;
+			firmware-name = "omap4-ipu-fw.xem3";
+			mboxes = <&mailbox &mbox_ipu>;
+			status = "disabled";
+		};
+
+		aes1_target: target-module@4b501000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4b501080 0x4>,
+			      <0x4b501084 0x4>,
+			      <0x4b501088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+			clocks = <&l4_secure_clkctrl OMAP4_AES1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b501000 0x1000>;
+
+			aes1: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 111>, <&sdma 110>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		aes2_target: target-module@4b701000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4b701080 0x4>,
+			      <0x4b701084 0x4>,
+			      <0x4b701088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+			clocks = <&l4_secure_clkctrl OMAP4_AES2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b701000 0x1000>;
+
+			aes2: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 114>, <&sdma 113>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		sham_target: target-module@4b100000 {
+			compatible = "ti,sysc-omap3-sham", "ti,sysc";
+			reg = <0x4b100100 0x4>,
+			      <0x4b100110 0x4>,
+			      <0x4b100114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */
+			clocks = <&l4_secure_clkctrl OMAP4_SHA2MD5_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b100000 0x1000>;
+
+			sham: sham@0 {
+				compatible = "ti,omap4-sham";
+				reg = <0 0x300>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 119>;
+				dma-names = "rx";
+			};
+		};
+
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			ti,tranxdone-status-mask = <0x80>;
+			clocks = <&sys_clkin_ck>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			status = "disabled";
+		};
+
+		abb_iva: regulator-abb-iva {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_iva";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			ti,tranxdone-status-mask = <0x80000000>;
+			clocks = <&sys_clkin_ck>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			status = "disabled";
+		};
+
+		sgx_module: target-module@56000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5600fe00 0x4>,
+			      <0x5600fe10 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			power-domains = <&prm_gfx>;
+			clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x56000000 0x2000000>;
+
+			/*
+			 * Closed source PowerVR driver, no child device
+			 * binding or driver in mainline
+			 */
+		};
+
+		/*
+		 * DSS is only using l3 mapping without l4 as noted in the TRM
+		 * "10.1.3 DSS Register Manual" for omap4460.
+		 */
+		target-module@58000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x58000000 4>,
+			      <0x58000014 4>;
+			reg-names = "rev", "syss";
+			ti,syss-mask = <1>;
+			power-domains = <&prm_dss>;
+			clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 0>,
+				 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
+				 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>,
+				 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
+			clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x58000000 0x1000000>;
+
+			dss: dss@0 {
+				compatible = "ti,omap4-dss";
+				reg = <0 0x80>;
+				status = "disabled";
+				clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0 0x1000000>;
+
+				target-module@1000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x1000 0x4>,
+					      <0x1010 0x4>,
+					      <0x1014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-midle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+						 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+					clock-names = "fck", "sys_clk";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x1000 0x1000>;
+
+					dispc@0 {
+						compatible = "ti,omap4-dispc";
+						reg = <0 0x1000>;
+						interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+						clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
+						clock-names = "fck";
+					};
+				};
+
+				target-module@2000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x2000 0x4>,
+					      <0x2010 0x4>,
+					      <0x2014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+						 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+					clock-names = "fck", "sys_clk";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x2000 0x1000>;
+
+					rfbi: encoder@0  {
+						reg = <0 0x1000>;
+						status = "disabled";
+						clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, <&l3_div_ck>;
+						clock-names = "fck", "ick";
+					};
+				};
+
+				target-module@3000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x3000 0x4>;
+					reg-names = "rev";
+					clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+					clock-names = "sys_clk";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x3000 0x1000>;
+
+					venc: encoder@0 {
+						compatible = "ti,omap4-venc";
+						reg = <0 0x1000>;
+						status = "disabled";
+						clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>;
+						clock-names = "fck";
+					};
+				};
+
+				target-module@4000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x4000 0x4>,
+					      <0x4010 0x4>,
+					      <0x4014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x4000 0x1000>;
+
+					dsi1: encoder@0 {
+						compatible = "ti,omap4-dsi";
+						reg = <0 0x200>,
+						      <0x200 0x40>,
+						      <0x300 0x20>;
+						reg-names = "proto", "phy", "pll";
+						interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+							 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+
+				target-module@5000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x5000 0x4>,
+					      <0x5010 0x4>,
+					      <0x5014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x5000 0x1000>;
+
+					dsi2: encoder@0 {
+						compatible = "ti,omap4-dsi";
+						reg = <0 0x200>,
+						      <0x200 0x40>,
+						      <0x300 0x20>;
+						reg-names = "proto", "phy", "pll";
+						interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>,
+						         <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+
+				target-module@6000 {
+					compatible = "ti,sysc-omap4", "ti,sysc";
+					reg = <0x6000 0x4>,
+					      <0x6010 0x4>;
+					reg-names = "rev", "sysc";
+					/*
+					 * Has SYSC_IDLE_SMART and SYSC_IDLE_SMART_WKUP
+					 * but HDMI audio will fail with them.
+					 */
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>;
+					ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
+					clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
+						 <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>;
+					clock-names = "fck", "dss_clk";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x6000 0x2000>;
+
+					hdmi: encoder@0 {
+					compatible = "ti,omap4-hdmi";
+						reg = <0 0x200>,
+						      <0x200 0x100>,
+						      <0x300 0x100>,
+						      <0x400 0x1000>;
+						reg-names = "wp", "pll", "phy", "core";
+						interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>,
+						         <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+						dmas = <&sdma 76>;
+						dma-names = "audio_tx";
+					};
+				};
+			};
+		};
+
+		iva_hd_target: target-module@5a000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5a05a400 0x4>,
+			      <0x5a05a410 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			power-domains = <&prm_ivahd>;
+			resets = <&prm_ivahd 2>;
+			reset-names = "rstctrl";
+			clocks = <&ivahd_clkctrl OMAP4_IVA_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x5a000000 0x5a000000 0x1000000>,
+				 <0x5b000000 0x5b000000 0x1000000>;
+
+			iva {
+				compatible = "ti,ivahd";
+			};
+		};
+	};
+};
+
+#include "omap4-l4.dtsi"
+#include "omap4-l4-abe.dtsi"
+#include "omap44xx-clocks.dtsi"
+
+&prm {
+	prm_mpu: prm@300 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x300 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_tesla: prm@400 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x400 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_abe: prm@500 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x500 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_always_on_core: prm@600 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x600 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_core: prm@700 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x700 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_ivahd: prm@f00 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0xf00 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_cam: prm@1000 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1000 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dss: prm@1100 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1100 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_gfx: prm@1200 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1200 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_l3init: prm@1300 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1300 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_l4per: prm@1400 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1400 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_cefuse: prm@1600 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1600 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_wkup: prm@1700 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1700 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_emu: prm@1900 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1900 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dss: prm@1100 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1100 0x40>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_device: prm@1b00 {
+		compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1b00 0x40>;
+		#reset-cells = <1>;
+	};
+};
+
+/* Preferred always-on timer for clockevent */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&l4_wkup_clkctrl OMAP4_TIMER1_CLKCTRL 24>;
+		assigned-clock-parents = <&sys_32k_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap443x-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap443x-clocks.dtsi
index 39297868ec85..581e088231b5 100644
--- a/arch/arm/boot/dts/omap443x-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap443x-clocks.dtsi
@@ -8,6 +8,7 @@
 	bandgap_fclk: bandgap_fclk@1888 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "bandgap_fclk";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x1888>;
diff --git a/arch/arm/boot/dts/omap443x.dtsi b/arch/arm/boot/dts/ti/omap/omap443x.dtsi
index cbcdcb4e7d1c..2104170fe2cd 100644
--- a/arch/arm/boot/dts/omap443x.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap443x.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP443x SoC
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include "omap4.dtsi"
@@ -33,10 +30,12 @@
 	};
 
 	ocp {
+		/* 4430 has only gpio_86 tshut and no talert interrupt */
 		bandgap: bandgap@4a002260 {
 			reg = <0x4a002260 0x4
 			       0x4a00232C 0x4>;
 			compatible = "ti,omap4430-bandgap";
+			gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 
 			#thermal-sensor-cells = <0>;
 		};
@@ -70,7 +69,18 @@
 };
 
 &cpu_thermal {
+	thermal-sensors = <&bandgap>;
 	coefficients = <0 20000>;
 };
 
 /include/ "omap443x-clocks.dtsi"
+
+/*
+ * Use dpll_per for sgx at 307.2MHz like droid4 stock v3.0.8 Android kernel
+ */
+&sgx_module {
+	assigned-clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 24>,
+			  <&dpll_per_m7x2_ck>;
+	assigned-clock-rates = <0>, <307200000>;
+	assigned-clock-parents = <&dpll_per_m7x2_ck>;
+};
diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/ti/omap/omap4460.dtsi
index 2223dc0d63c0..a6764750d447 100644
--- a/arch/arm/boot/dts/omap4460.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4460.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP4460 SoC
  *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include "omap4.dtsi"
 
@@ -26,13 +23,6 @@
 		};
 	};
 
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
-		ti,hwmods = "debugss";
-	};
-
 	thermal-zones {
 		#include "omap4-cpu-thermal.dtsi"
 	};
@@ -89,6 +79,7 @@
 };
 
 &cpu_thermal {
+	thermal-sensors = <&bandgap>;
 	coefficients = <348 (-9301)>;
 };
 
@@ -128,4 +119,10 @@
 		 <0x00030000 0x00030000 0x00010000>;
 };
 
+&pmu {
+	compatible = "arm,cortex-a9-pmu";
+	interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 /include/ "omap446x-clocks.dtsi"
diff --git a/arch/arm/boot/dts/omap446x-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap446x-clocks.dtsi
index 0f41714cffbb..d9362fef6720 100644
--- a/arch/arm/boot/dts/omap446x-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap446x-clocks.dtsi
@@ -8,6 +8,7 @@
 	div_ts_ck: div_ts_ck@1888 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_ts_ck";
 		clocks = <&l4_wkup_clk_mux_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1888>;
@@ -17,6 +18,7 @@
 	bandgap_ts_fclk: bandgap_ts_fclk@1888 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "bandgap_ts_fclk";
 		clocks = <&div_ts_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x1888>;
diff --git a/arch/arm/boot/dts/omap44xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap44xx-clocks.dtsi
index e9d9c8460682..8df73d285638 100644
--- a/arch/arm/boot/dts/omap44xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap44xx-clocks.dtsi
@@ -8,18 +8,21 @@
 	extalt_clkin_ck: extalt_clkin_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "extalt_clkin_ck";
 		clock-frequency = <59000000>;
 	};
 
 	pad_clks_src_ck: pad_clks_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pad_clks_src_ck";
 		clock-frequency = <12000000>;
 	};
 
 	pad_clks_ck: pad_clks_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "pad_clks_ck";
 		clocks = <&pad_clks_src_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0108>;
@@ -28,24 +31,28 @@
 	pad_slimbus_core_clks_ck: pad_slimbus_core_clks_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pad_slimbus_core_clks_ck";
 		clock-frequency = <12000000>;
 	};
 
 	secure_32k_clk_src_ck: secure_32k_clk_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "secure_32k_clk_src_ck";
 		clock-frequency = <32768>;
 	};
 
 	slimbus_src_clk: slimbus_src_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "slimbus_src_clk";
 		clock-frequency = <12000000>;
 	};
 
 	slimbus_clk: slimbus_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "slimbus_clk";
 		clocks = <&slimbus_src_clk>;
 		ti,bit-shift = <10>;
 		reg = <0x0108>;
@@ -54,84 +61,98 @@
 	sys_32k_ck: sys_32k_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_32k_ck";
 		clock-frequency = <32768>;
 	};
 
 	virt_12000000_ck: virt_12000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_12000000_ck";
 		clock-frequency = <12000000>;
 	};
 
 	virt_13000000_ck: virt_13000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_13000000_ck";
 		clock-frequency = <13000000>;
 	};
 
 	virt_16800000_ck: virt_16800000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_16800000_ck";
 		clock-frequency = <16800000>;
 	};
 
 	virt_19200000_ck: virt_19200000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
 	virt_26000000_ck: virt_26000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
 	virt_27000000_ck: virt_27000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_27000000_ck";
 		clock-frequency = <27000000>;
 	};
 
 	virt_38400000_ck: virt_38400000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_38400000_ck";
 		clock-frequency = <38400000>;
 	};
 
 	tie_low_clock_ck: tie_low_clock_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "tie_low_clock_ck";
 		clock-frequency = <0>;
 	};
 
 	utmi_phy_clkout_ck: utmi_phy_clkout_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "utmi_phy_clkout_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60mhsp1_ck: xclk60mhsp1_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp1_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60mhsp2_ck: xclk60mhsp2_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp2_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60motg_ck: xclk60motg_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60motg_ck";
 		clock-frequency = <60000000>;
 	};
 
 	dpll_abe_ck: dpll_abe_ck@1e0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-m4xen-clock";
+		clock-output-names = "dpll_abe_ck";
 		clocks = <&abe_dpll_refclk_mux_ck>, <&abe_dpll_bypass_clk_mux_ck>;
 		reg = <0x01e0>, <0x01e4>, <0x01ec>, <0x01e8>;
 	};
@@ -139,6 +160,7 @@
 	dpll_abe_x2_ck: dpll_abe_x2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_abe_x2_ck";
 		clocks = <&dpll_abe_ck>;
 		reg = <0x01f0>;
 	};
@@ -146,6 +168,7 @@
 	dpll_abe_m2x2_ck: dpll_abe_m2x2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -157,6 +180,7 @@
 	abe_24m_fclk: abe_24m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "abe_24m_fclk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
@@ -165,6 +189,7 @@
 	abe_clk: abe_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_clk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x0108>;
@@ -175,6 +200,7 @@
 	dpll_abe_m3x2_ck: dpll_abe_m3x2_ck@1f4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m3x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -186,6 +212,7 @@
 	core_hsd_byp_clk_mux_ck: core_hsd_byp_clk_mux_ck@12c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "core_hsd_byp_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x012c>;
@@ -194,6 +221,7 @@
 	dpll_core_ck: dpll_core_ck@120 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin_ck>, <&core_hsd_byp_clk_mux_ck>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
@@ -201,12 +229,14 @@
 	dpll_core_x2_ck: dpll_core_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
 	dpll_core_m6x2_ck: dpll_core_m6x2_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m6x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -218,6 +248,7 @@
 	dpll_core_m2_ck: dpll_core_m2_ck@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m2_ck";
 		clocks = <&dpll_core_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -229,6 +260,7 @@
 	ddrphy_ck: ddrphy_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "ddrphy_ck";
 		clocks = <&dpll_core_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -237,6 +269,7 @@
 	dpll_core_m5x2_ck: dpll_core_m5x2_ck@13c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m5x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -248,6 +281,7 @@
 	div_core_ck: div_core_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_core_ck";
 		clocks = <&dpll_core_m5x2_ck>;
 		reg = <0x0100>;
 		ti,max-div = <2>;
@@ -256,6 +290,7 @@
 	div_iva_hs_clk: div_iva_hs_clk@1dc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_iva_hs_clk";
 		clocks = <&dpll_core_m5x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x01dc>;
@@ -265,6 +300,7 @@
 	div_mpu_hs_clk: div_mpu_hs_clk@19c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_mpu_hs_clk";
 		clocks = <&dpll_core_m5x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x019c>;
@@ -274,6 +310,7 @@
 	dpll_core_m4x2_ck: dpll_core_m4x2_ck@138 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m4x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -285,6 +322,7 @@
 	dll_clk_div_ck: dll_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dll_clk_div_ck";
 		clocks = <&dpll_core_m4x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -293,6 +331,7 @@
 	dpll_abe_m2_ck: dpll_abe_m2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2_ck";
 		clocks = <&dpll_abe_ck>;
 		ti,max-div = <31>;
 		reg = <0x01f0>;
@@ -302,6 +341,7 @@
 	dpll_core_m3x2_gate_ck: dpll_core_m3x2_gate_ck@134 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "dpll_core_m3x2_gate_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0134>;
@@ -310,6 +350,7 @@
 	dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck@134 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-divider-clock";
+		clock-output-names = "dpll_core_m3x2_div_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0134>;
@@ -319,12 +360,14 @@
 	dpll_core_m3x2_ck: dpll_core_m3x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "dpll_core_m3x2_ck";
 		clocks = <&dpll_core_m3x2_gate_ck>, <&dpll_core_m3x2_div_ck>;
 	};
 
 	dpll_core_m7x2_ck: dpll_core_m7x2_ck@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m7x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -336,6 +379,7 @@
 	iva_hsd_byp_clk_mux_ck: iva_hsd_byp_clk_mux_ck@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "iva_hsd_byp_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&div_iva_hs_clk>;
 		ti,bit-shift = <23>;
 		reg = <0x01ac>;
@@ -344,6 +388,7 @@
 	dpll_iva_ck: dpll_iva_ck@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_iva_ck";
 		clocks = <&sys_clkin_ck>, <&iva_hsd_byp_clk_mux_ck>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 		assigned-clocks = <&dpll_iva_ck>;
@@ -353,12 +398,14 @@
 	dpll_iva_x2_ck: dpll_iva_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_iva_x2_ck";
 		clocks = <&dpll_iva_ck>;
 	};
 
 	dpll_iva_m4x2_ck: dpll_iva_m4x2_ck@1b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_m4x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -372,6 +419,7 @@
 	dpll_iva_m5x2_ck: dpll_iva_m5x2_ck@1bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_m5x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -385,6 +433,7 @@
 	dpll_mpu_ck: dpll_mpu_ck@160 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin_ck>, <&div_mpu_hs_clk>;
 		reg = <0x0160>, <0x0164>, <0x016c>, <0x0168>;
 	};
@@ -392,6 +441,7 @@
 	dpll_mpu_m2_ck: dpll_mpu_m2_ck@170 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -403,6 +453,7 @@
 	per_hs_clk_div_ck: per_hs_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_hs_clk_div_ck";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -411,6 +462,7 @@
 	usb_hs_clk_div_ck: usb_hs_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "usb_hs_clk_div_ck";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <3>;
@@ -419,6 +471,7 @@
 	l3_div_ck: l3_div_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3_div_ck";
 		clocks = <&div_core_ck>;
 		ti,bit-shift = <4>;
 		ti,max-div = <2>;
@@ -428,6 +481,7 @@
 	l4_div_ck: l4_div_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l4_div_ck";
 		clocks = <&l3_div_ck>;
 		ti,bit-shift = <8>;
 		ti,max-div = <2>;
@@ -437,6 +491,7 @@
 	lp_clk_div_ck: lp_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "lp_clk_div_ck";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -445,6 +500,7 @@
 	mpu_periphclk: mpu_periphclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_periphclk";
 		clocks = <&dpll_mpu_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -453,6 +509,7 @@
 	ocp_abe_iclk: ocp_abe_iclk@528 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "ocp_abe_iclk";
 		clocks = <&abe_clkctrl OMAP4_AESS_CLKCTRL 24>;
 		ti,bit-shift = <24>;
 		reg = <0x0528>;
@@ -462,6 +519,7 @@
 	per_abe_24m_fclk: per_abe_24m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_abe_24m_fclk";
 		clocks = <&dpll_abe_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -470,6 +528,7 @@
 	dummy_ck: dummy_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "dummy_ck";
 		clock-frequency = <0>;
 	};
 };
@@ -478,6 +537,7 @@
 	sys_clkin_ck: sys_clkin_ck@110 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin_ck";
 		clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
 		reg = <0x0110>;
 		ti,index-starts-at-one;
@@ -486,6 +546,7 @@
 	abe_dpll_bypass_clk_mux_ck: abe_dpll_bypass_clk_mux_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_bypass_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&sys_32k_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x0108>;
@@ -494,6 +555,7 @@
 	abe_dpll_refclk_mux_ck: abe_dpll_refclk_mux_ck@10c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_refclk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&sys_32k_ck>;
 		reg = <0x010c>;
 	};
@@ -501,6 +563,7 @@
 	dbgclk_mux_ck: dbgclk_mux_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dbgclk_mux_ck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -509,6 +572,7 @@
 	l4_wkup_clk_mux_ck: l4_wkup_clk_mux_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "l4_wkup_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&lp_clk_div_ck>;
 		reg = <0x0108>;
 	};
@@ -516,6 +580,7 @@
 	syc_clk_div_ck: syc_clk_div_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "syc_clk_div_ck";
 		clocks = <&sys_clkin_ck>;
 		reg = <0x0100>;
 		ti,max-div = <2>;
@@ -524,6 +589,7 @@
 	usim_ck: usim_ck@1858 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "usim_ck";
 		clocks = <&dpll_per_m4x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1858>;
@@ -533,6 +599,7 @@
 	usim_fclk: usim_fclk@1858 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usim_fclk";
 		clocks = <&usim_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x1858>;
@@ -541,6 +608,7 @@
 	trace_clk_div_ck: trace_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "ti,clkdm-gate-clock";
+		clock-output-names = "trace_clk_div_ck";
 		clocks = <&emu_sys_clkctrl OMAP4_DEBUGSS_CLKCTRL 24>;
 	};
 };
@@ -548,6 +616,7 @@
 &prm_clockdomains {
 	emu_sys_clkdm: emu_sys_clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "emu_sys_clkdm";
 		clocks = <&trace_clk_div_ck>;
 	};
 };
@@ -556,6 +625,7 @@
 	per_hsd_byp_clk_mux_ck: per_hsd_byp_clk_mux_ck@14c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "per_hsd_byp_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&per_hs_clk_div_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x014c>;
@@ -564,6 +634,7 @@
 	dpll_per_ck: dpll_per_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin_ck>, <&per_hsd_byp_clk_mux_ck>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
@@ -571,6 +642,7 @@
 	dpll_per_m2_ck: dpll_per_m2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		reg = <0x0150>;
@@ -580,6 +652,7 @@
 	dpll_per_x2_ck: dpll_per_x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_per_x2_ck";
 		clocks = <&dpll_per_ck>;
 		reg = <0x0150>;
 	};
@@ -587,6 +660,7 @@
 	dpll_per_m2x2_ck: dpll_per_m2x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -598,6 +672,7 @@
 	dpll_per_m3x2_gate_ck: dpll_per_m3x2_gate_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "dpll_per_m3x2_gate_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0154>;
@@ -606,6 +681,7 @@
 	dpll_per_m3x2_div_ck: dpll_per_m3x2_div_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-divider-clock";
+		clock-output-names = "dpll_per_m3x2_div_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0154>;
@@ -615,12 +691,14 @@
 	dpll_per_m3x2_ck: dpll_per_m3x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "dpll_per_m3x2_ck";
 		clocks = <&dpll_per_m3x2_gate_ck>, <&dpll_per_m3x2_div_ck>;
 	};
 
 	dpll_per_m4x2_ck: dpll_per_m4x2_ck@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m4x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -632,6 +710,7 @@
 	dpll_per_m5x2_ck: dpll_per_m5x2_ck@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m5x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -643,6 +722,7 @@
 	dpll_per_m6x2_ck: dpll_per_m6x2_ck@160 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m6x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -654,6 +734,7 @@
 	dpll_per_m7x2_ck: dpll_per_m7x2_ck@164 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m7x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -665,6 +746,7 @@
 	dpll_usb_ck: dpll_usb_ck@180 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
+		clock-output-names = "dpll_usb_ck";
 		clocks = <&sys_clkin_ck>, <&usb_hs_clk_div_ck>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
@@ -672,6 +754,7 @@
 	dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck@1b4 {
 		#clock-cells = <0>;
 		compatible = "ti,fixed-factor-clock";
+		clock-output-names = "dpll_usb_clkdcoldo_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,clock-div = <1>;
 		ti,autoidle-shift = <8>;
@@ -683,6 +766,7 @@
 	dpll_usb_m2_ck: dpll_usb_m2_ck@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_usb_m2_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -694,6 +778,7 @@
 	ducati_clk_mux_ck: ducati_clk_mux_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "ducati_clk_mux_ck";
 		clocks = <&div_core_ck>, <&dpll_per_m6x2_ck>;
 		reg = <0x0100>;
 	};
@@ -701,6 +786,7 @@
 	func_12m_fclk: func_12m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -709,6 +795,7 @@
 	func_24m_clk: func_24m_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -717,6 +804,7 @@
 	func_24mc_fclk: func_24mc_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24mc_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
@@ -725,6 +813,7 @@
 	func_48m_fclk: func_48m_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "func_48m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		reg = <0x0108>;
 		ti,dividers = <4>, <8>;
@@ -733,6 +822,7 @@
 	func_48mc_fclk: func_48mc_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_48mc_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -741,6 +831,7 @@
 	func_64m_fclk: func_64m_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "func_64m_fclk";
 		clocks = <&dpll_per_m4x2_ck>;
 		reg = <0x0108>;
 		ti,dividers = <2>, <4>;
@@ -749,6 +840,7 @@
 	func_96m_fclk: func_96m_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "func_96m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		reg = <0x0108>;
 		ti,dividers = <2>, <4>;
@@ -757,6 +849,7 @@
 	init_60m_fclk: init_60m_fclk@104 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "init_60m_fclk";
 		clocks = <&dpll_usb_m2_ck>;
 		reg = <0x0104>;
 		ti,dividers = <1>, <8>;
@@ -765,22 +858,16 @@
 	per_abe_nc_fclk: per_abe_nc_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "per_abe_nc_fclk";
 		clocks = <&dpll_abe_m2_ck>;
 		reg = <0x0108>;
 		ti,max-div = <2>;
 	};
 
-	sha2md5_fck: sha2md5_fck@15c8 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l3_div_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x15c8>;
-	};
-
 	usb_phy_cm_clk32k: usb_phy_cm_clk32k@640 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy_cm_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0640>;
@@ -790,6 +877,7 @@
 &cm2_clockdomains {
 	l3_init_clkdm: l3_init_clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "l3_init_clkdm";
 		clocks = <&dpll_usb_ck>;
 	};
 };
@@ -798,6 +886,7 @@
 	auxclk0_src_gate_ck: auxclk0_src_gate_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk0_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0310>;
@@ -806,6 +895,7 @@
 	auxclk0_src_mux_ck: auxclk0_src_mux_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk0_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0310>;
@@ -814,12 +904,14 @@
 	auxclk0_src_ck: auxclk0_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk0_src_ck";
 		clocks = <&auxclk0_src_gate_ck>, <&auxclk0_src_mux_ck>;
 	};
 
 	auxclk0_ck: auxclk0_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk0_ck";
 		clocks = <&auxclk0_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -829,6 +921,7 @@
 	auxclk1_src_gate_ck: auxclk1_src_gate_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk1_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0314>;
@@ -837,6 +930,7 @@
 	auxclk1_src_mux_ck: auxclk1_src_mux_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk1_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0314>;
@@ -845,12 +939,14 @@
 	auxclk1_src_ck: auxclk1_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk1_src_ck";
 		clocks = <&auxclk1_src_gate_ck>, <&auxclk1_src_mux_ck>;
 	};
 
 	auxclk1_ck: auxclk1_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk1_ck";
 		clocks = <&auxclk1_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -860,6 +956,7 @@
 	auxclk2_src_gate_ck: auxclk2_src_gate_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk2_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0318>;
@@ -868,6 +965,7 @@
 	auxclk2_src_mux_ck: auxclk2_src_mux_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk2_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0318>;
@@ -876,12 +974,14 @@
 	auxclk2_src_ck: auxclk2_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk2_src_ck";
 		clocks = <&auxclk2_src_gate_ck>, <&auxclk2_src_mux_ck>;
 	};
 
 	auxclk2_ck: auxclk2_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk2_ck";
 		clocks = <&auxclk2_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -891,6 +991,7 @@
 	auxclk3_src_gate_ck: auxclk3_src_gate_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk3_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x031c>;
@@ -899,6 +1000,7 @@
 	auxclk3_src_mux_ck: auxclk3_src_mux_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk3_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x031c>;
@@ -907,12 +1009,14 @@
 	auxclk3_src_ck: auxclk3_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk3_src_ck";
 		clocks = <&auxclk3_src_gate_ck>, <&auxclk3_src_mux_ck>;
 	};
 
 	auxclk3_ck: auxclk3_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk3_ck";
 		clocks = <&auxclk3_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -922,6 +1026,7 @@
 	auxclk4_src_gate_ck: auxclk4_src_gate_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk4_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0320>;
@@ -930,6 +1035,7 @@
 	auxclk4_src_mux_ck: auxclk4_src_mux_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk4_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0320>;
@@ -938,12 +1044,14 @@
 	auxclk4_src_ck: auxclk4_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk4_src_ck";
 		clocks = <&auxclk4_src_gate_ck>, <&auxclk4_src_mux_ck>;
 	};
 
 	auxclk4_ck: auxclk4_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk4_ck";
 		clocks = <&auxclk4_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -953,6 +1061,7 @@
 	auxclk5_src_gate_ck: auxclk5_src_gate_ck@324 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk5_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0324>;
@@ -961,6 +1070,7 @@
 	auxclk5_src_mux_ck: auxclk5_src_mux_ck@324 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk5_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0324>;
@@ -969,12 +1079,14 @@
 	auxclk5_src_ck: auxclk5_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk5_src_ck";
 		clocks = <&auxclk5_src_gate_ck>, <&auxclk5_src_mux_ck>;
 	};
 
 	auxclk5_ck: auxclk5_ck@324 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk5_ck";
 		clocks = <&auxclk5_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -984,6 +1096,7 @@
 	auxclkreq0_ck: auxclkreq0_ck@210 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq0_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0210>;
@@ -992,6 +1105,7 @@
 	auxclkreq1_ck: auxclkreq1_ck@214 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq1_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0214>;
@@ -1000,6 +1114,7 @@
 	auxclkreq2_ck: auxclkreq2_ck@218 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq2_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0218>;
@@ -1008,6 +1123,7 @@
 	auxclkreq3_ck: auxclkreq3_ck@21c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq3_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x021c>;
@@ -1016,6 +1132,7 @@
 	auxclkreq4_ck: auxclkreq4_ck@220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq4_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0220>;
@@ -1024,6 +1141,7 @@
 	auxclkreq5_ck: auxclkreq5_ck@224 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq5_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0224>;
@@ -1033,6 +1151,7 @@
 &cm1 {
 	mpuss_cm: mpuss_cm@300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpuss_cm";
 		reg = <0x300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1040,6 +1159,7 @@
 
 		mpuss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpuss_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1047,6 +1167,7 @@
 
 	tesla_cm: tesla_cm@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "tesla_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1054,6 +1175,7 @@
 
 		tesla_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "tesla_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1061,6 +1183,7 @@
 
 	abe_cm: abe_cm@500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "abe_cm";
 		reg = <0x500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1068,6 +1191,7 @@
 
 		abe_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "abe_clkctrl";
 			reg = <0x20 0x6c>;
 			#clock-cells = <2>;
 		};
@@ -1078,6 +1202,7 @@
 &cm2 {
 	l4_ao_cm: l4_ao_cm@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_ao_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1085,6 +1210,7 @@
 
 		l4_ao_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_ao_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
@@ -1092,6 +1218,7 @@
 
 	l3_1_cm: l3_1_cm@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_1_cm";
 		reg = <0x700 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1099,6 +1226,7 @@
 
 		l3_1_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1106,6 +1234,7 @@
 
 	l3_2_cm: l3_2_cm@800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_2_cm";
 		reg = <0x800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1113,6 +1242,7 @@
 
 		l3_2_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_2_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
@@ -1120,6 +1250,7 @@
 
 	ducati_cm: ducati_cm@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ducati_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1127,6 +1258,7 @@
 
 		ducati_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ducati_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1134,6 +1266,7 @@
 
 	l3_dma_cm: l3_dma_cm@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_dma_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1141,6 +1274,7 @@
 
 		l3_dma_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_dma_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1148,6 +1282,7 @@
 
 	l3_emif_cm: l3_emif_cm@b00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_emif_cm";
 		reg = <0xb00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1155,6 +1290,7 @@
 
 		l3_emif_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_emif_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
@@ -1162,6 +1298,7 @@
 
 	d2d_cm: d2d_cm@c00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "d2d_cm";
 		reg = <0xc00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1169,6 +1306,7 @@
 
 		d2d_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "d2d_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1176,6 +1314,7 @@
 
 	l4_cfg_cm: l4_cfg_cm@d00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_cfg_cm";
 		reg = <0xd00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1183,6 +1322,7 @@
 
 		l4_cfg_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_cfg_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
@@ -1190,6 +1330,7 @@
 
 	l3_instr_cm: l3_instr_cm@e00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_instr_cm";
 		reg = <0xe00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1197,6 +1338,7 @@
 
 		l3_instr_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_instr_clkctrl";
 			reg = <0x20 0x24>;
 			#clock-cells = <2>;
 		};
@@ -1204,6 +1346,7 @@
 
 	ivahd_cm: ivahd_cm@f00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ivahd_cm";
 		reg = <0xf00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1211,6 +1354,7 @@
 
 		ivahd_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ivahd_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
@@ -1218,6 +1362,7 @@
 
 	iss_cm: iss_cm@1000 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "iss_cm";
 		reg = <0x1000 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1225,6 +1370,7 @@
 
 		iss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "iss_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
@@ -1232,6 +1378,7 @@
 
 	l3_dss_cm: l3_dss_cm@1100 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_dss_cm";
 		reg = <0x1100 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1239,6 +1386,7 @@
 
 		l3_dss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_dss_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1246,6 +1394,7 @@
 
 	l3_gfx_cm: l3_gfx_cm@1200 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_gfx_cm";
 		reg = <0x1200 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1253,6 +1402,7 @@
 
 		l3_gfx_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_gfx_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1260,6 +1410,7 @@
 
 	l3_init_cm: l3_init_cm@1300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_init_cm";
 		reg = <0x1300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1267,30 +1418,40 @@
 
 		l3_init_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_init_clkctrl";
 			reg = <0x20 0xc4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_per_cm: l4_per_cm@1400 {
+	l4_per_cm: clock@1400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_per_cm";
 		reg = <0x1400 0x200>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1400 0x200>;
 
-		l4_per_clkctrl: clk@20 {
+		l4_per_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_per_clkctrl";
 			reg = <0x20 0x144>;
 			#clock-cells = <2>;
 		};
-	};
 
+		l4_secure_clkctrl: clock@1a0 {
+			compatible = "ti,clkctrl";
+			clock-output-names = "l4_secure_clkctrl";
+			reg = <0x1a0 0x3c>;
+			#clock-cells = <2>;
+		};
+	};
 };
 
 &prm {
 	l4_wkup_cm: l4_wkup_cm@1800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_wkup_cm";
 		reg = <0x1800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1298,6 +1459,7 @@
 
 		l4_wkup_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_clkctrl";
 			reg = <0x20 0x5c>;
 			#clock-cells = <2>;
 		};
@@ -1305,6 +1467,7 @@
 
 	emu_sys_cm: emu_sys_cm@1a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "emu_sys_cm";
 		reg = <0x1a00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1312,6 +1475,7 @@
 
 		emu_sys_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emu_sys_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/ti/omap/omap5-board-common.dtsi
index 68ac04641bdb..8946b5580cd9 100644
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap5-board-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include "omap5.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
@@ -30,14 +30,6 @@
 		regulator-max-microvolt = <5000000>;
 	};
 
-	vdds_1v8_main: fixedregulator-vdds_1v8_main {
-		compatible = "regulator-fixed";
-		regulator-name = "vdds_1v8_main";
-		vin-supply = <&smps7_reg>;
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
 	vmmcsd_fixed: fixedregulator-mmcsd {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
@@ -64,7 +56,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
 		clocks = <&auxclk1_ck>;
@@ -149,7 +141,7 @@
 
 &gpio8 {
 	/* TI trees use GPIO instead of msecure, see also muxing */
-	p234 {
+	msecure-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -164,13 +156,13 @@
 			&led_gpio_pins
 	>;
 
-	twl6040_pins: pinmux_twl6040_pins {
+	twl6040_pins: twl6040-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
 		>;
 	};
 
-	mcpdm_pins: pinmux_mcpdm_pins {
+	mcpdm_pins: mcpdm-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_clks.abe_clks */
 			OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_ul_data.abemcpdm_ul_data */
@@ -180,7 +172,7 @@
 		>;
 	};
 
-	mcbsp1_pins: pinmux_mcbsp1_pins {
+	mcbsp1_pins: mcbsp1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1)		/* abedmic_clk2.abemcbsp1_fsx */
 			OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* abedmic_clk3.abemcbsp1_dx */
@@ -189,7 +181,7 @@
 		>;
 	};
 
-	mcbsp2_pins: pinmux_mcbsp2_pins {
+	mcbsp2_pins: mcbsp2-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dr.abemcbsp2_dr */
 			OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dx.abemcbsp2_dx */
@@ -198,14 +190,14 @@
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
 			OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
 		>;
 	};
 
-	mcspi2_pins: pinmux_mcspi2_pins {
+	mcspi2_pins: mcspi2-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)		/*  mcspi2_clk */
 			OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0)		/*  mcspi2_simo */
@@ -214,7 +206,7 @@
 		>;
 	};
 
-	mcspi3_pins: pinmux_mcspi3_pins {
+	mcspi3_pins: mcspi3-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1)		/*  mcspi3_somi */
 			OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1)		/*  mcspi3_cs0 */
@@ -223,7 +215,7 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
 			OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
@@ -234,20 +226,20 @@
 		>;
 	};
 
-	wlan_pins: pinmux_wlan_pins {
+	wlan_pins: wlan-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
 		>;
 	};
 
 	/* TI trees use GPIO mode; msecure mode does not work reliably? */
-	palmas_msecure_pins: palmas_msecure_pins {
+	palmas_msecure_pins: palmas-msecure-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */
 		>;
 	};
 
-	usbhost_pins: pinmux_usbhost_pins {
+	usbhost_pins: usbhost-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
 			OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
@@ -260,13 +252,13 @@
 		>;
 	};
 
-	led_gpio_pins: pinmux_led_gpio_pins {
+	led_gpio_pins: led-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
 		>;
 	};
 
-	uart1_pins: pinmux_uart1_pins {
+	uart1_pins: uart1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
 			OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
@@ -275,14 +267,14 @@
 		>;
 	};
 
-	uart3_pins: pinmux_uart3_pins {
+	uart3_pins: uart3-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
 			OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
 		>;
 	};
 
-	uart5_pins: pinmux_uart5_pins {
+	uart5_pins: uart5-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
 			OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
@@ -291,7 +283,7 @@
 		>;
 	};
 
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x13c, PIN_INPUT | MUX_MODE0)	/* hdmi_cec.hdmi_cec */
 			OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_scl.hdmi_ddc_scl */
@@ -299,7 +291,7 @@
 		>;
 	};
 
-	tpd12s015_pins: pinmux_tpd12s015_pins {
+	tpd12s015_pins: tpd12s015-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6)	/* hdmi_hpd.gpio7_193 */
 		>;
@@ -312,20 +304,20 @@
 			&usbhost_wkup_pins
 	>;
 
-	palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
+	palmas_sys_nirq_pins: palmas-sys-nirq-pins {
 		pinctrl-single,pins = <
 			/* sys_nirq1 is pulled down as the SoC is inverting it for GIC */
 			OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0)
 		>;
 	};
 
-	usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
+	usbhost_wkup_pins: usbhost-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
 		>;
 	};
 
-	wlcore_irq_pin: pinmux_wlcore_irq_pin {
+	wlcore_irq_pin: wlcore-irq-pin-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x40, PIN_INPUT | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
 		>;
@@ -423,9 +415,9 @@
 
 		gpadc: gpadc {
 			compatible = "ti,palmas-gpadc";
-			interrupts = <18 0
-				      16 0
-				      17 0>;
+			interrupts = <18 0>,
+				     <16 0>,
+				     <17 0>;
 			#io-channel-cells = <1>;
 			ti,channel0-current-microamp = <5>;
 			ti,channel3-current-microamp = <10>;
@@ -487,6 +479,7 @@
 					regulator-boot-on;
 				};
 
+				vdds_1v8_main:
 				smps7_reg: smps7 {
 					/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
 					regulator-name = "smps7";
@@ -743,11 +736,11 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 
 	/* vdda-supply populated in board specific dts file */
 
diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/ti/omap/omap5-cm-t54.dts
index e78d3718f145..6767382996ab 100644
--- a/arch/arm/boot/dts/omap5-cm-t54.dts
+++ b/arch/arm/boot/dts/ti/omap/omap5-cm-t54.dts
@@ -60,7 +60,7 @@
 	};
 
 	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
+	hsusb2_phy: hsusb2-phy-pins {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
 		#phy-cells = <0>;
@@ -84,36 +84,36 @@
 	};
 
 	lcd0: display {
-                compatible = "startek,startek-kd050c", "panel-dpi";
-                label = "lcd";
-
-                pinctrl-names = "default";
-                pinctrl-0 = <&lcd_pins>;
-
-                enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
-
-                panel-timing {
-                        clock-frequency = <33000000>;
-                        hactive = <800>;
-                        vactive = <480>;
-                        hfront-porch = <40>;
-                        hback-porch = <40>;
-                        hsync-len = <43>;
-                        vback-porch = <29>;
-                        vfront-porch = <13>;
-                        vsync-len = <3>;
-                        hsync-active = <0>;
-                        vsync-active = <0>;
-                        de-active = <1>;
-                        pixelclk-active = <1>;
-                };
-
-                port {
-                        lcd_in: endpoint {
-                                remote-endpoint = <&dpi_lcd_out>;
-                        };
-                };
-        };
+		compatible = "startek,startek-kd050c", "panel-dpi";
+		label = "lcd";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins>;
+
+		enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+
+		panel-timing {
+			clock-frequency = <33000000>;
+			hactive = <800>;
+			vactive = <480>;
+			hfront-porch = <40>;
+			hback-porch = <40>;
+			hsync-len = <43>;
+			vback-porch = <29>;
+			vfront-porch = <13>;
+			vsync-len = <3>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_lcd_out>;
+			};
+		};
+	};
 
 	hdmi0: connector0 {
 		compatible = "hdmi-connector";
@@ -176,13 +176,13 @@
 
 &omap5_pmx_wkup {
 
-	ads7846_pins: pinmux_ads7846_pins {
+	ads7846_pins: ads7846-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6)  /* llib_wakereqin.gpio1_wk15 */
 		>;
 	};
 
-	palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
+	palmas_sys_nirq_pins: palmas-sys-nirq-pins {
 		pinctrl-single,pins = <
 			/* sys_nirq1 is pulled down as the SoC is inverting it for GIC */
 			OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0)
@@ -197,27 +197,27 @@
 			&usbhost_pins
 	>;
 
-	led_gpio_pins: pinmux_led_gpio_pins {
+	led_gpio_pins: led-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
 		>;
 	};
 
-	i2c1_pins: pinmux_i2c1_pins {
+	i2c1_pins: i2c1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
 			OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
 		>;
 	};
 
-	i2c2_pins: pinmux_i2c2_pins {
+	i2c2_pins: i2c2-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
 			OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
 			OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
@@ -228,7 +228,7 @@
 		>;
 	};
 
-	mmc2_pins: pinmux_mmc2_pins {
+	mmc2_pins: mmc2-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
 			OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
@@ -243,7 +243,7 @@
 		>;
 	};
 
-	mmc3_pins: pinmux_mmc3_pins {
+	mmc3_pins: mmc3-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
 			OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
@@ -254,14 +254,14 @@
 		>;
 	};
 
-	wlan_gpios_pins: pinmux_wlan_gpios_pins {
+	wlan_gpios_pins: wlan-gpios-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
 			OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
 		>;
 	};
 
-	usbhost_pins: pinmux_usbhost_pins {
+	usbhost_pins: usbhost-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_strobe */
 			OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_data */
@@ -274,7 +274,7 @@
 		>;
 	};
 
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
 			OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
@@ -282,19 +282,19 @@
 		>;
 	};
 
-	lcd_pins: pinmux_lcd_pins {
+	lcd_pins: lcd-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
 		>;
 	};
 
-	hdmi_conn_pins: pinmux_hdmi_conn_pins {
+	hdmi_conn_pins: hdmi-conn-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
 		>;
 	};
 
-	dss_dpi_pins: pinmux_dss_dpi_pins {
+	dss_dpi_pins: dss-dpi-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
 			OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
@@ -327,7 +327,7 @@
 		>;
 	};
 
-	mcspi2_pins: pinmux_mcspi1_pins {
+	mcspi2_pins: mcspi1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
 			OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
@@ -354,7 +354,7 @@
 
 		interrupt-parent = <&gpio1>;
 		interrupts = <15 0>;			/* gpio1_wk15 */
-		pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		pendown-gpio = <&gpio1 15 GPIO_ACTIVE_LOW>;
 
 
 		ti,x-min = /bits/ 16 <0x0>;
@@ -644,8 +644,8 @@
 };
 
 &usb3 {
-       extcon = <&extcon_usb3>;
-       vbus-supply = <&smps10_out1_reg>;
+	extcon = <&extcon_usb3>;
+	vbus-supply = <&smps10_out1_reg>;
 };
 
 &cpu0 {
@@ -653,7 +653,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss_dpi_pins>;
@@ -677,12 +677,12 @@
 };
 
 &dsi2 {
-	status = "ok";
+	status = "okay";
 	vdd-supply = <&ldo4_reg>;
 };
 
 &hdmi {
-	status = "ok";
+	status = "okay";
 	vdda-supply = <&ldo4_reg>;
 
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/omap5-core-thermal.dtsi b/arch/arm/boot/dts/ti/omap/omap5-core-thermal.dtsi
index de8a3d456cf7..e0d8e39a0014 100644
--- a/arch/arm/boot/dts/omap5-core-thermal.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap5-core-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP543x SoC CORE thermal
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/omap5-gpu-thermal.dtsi b/arch/arm/boot/dts/ti/omap/omap5-gpu-thermal.dtsi
index bc3090f2e84b..1b4b7d9136c8 100644
--- a/arch/arm/boot/dts/omap5-gpu-thermal.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap5-gpu-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP543x SoC GPU thermal
  *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/omap5-igep0050.dts b/arch/arm/boot/dts/ti/omap/omap5-igep0050.dts
index 76e499d89d24..d4ca2e3a14dd 100644
--- a/arch/arm/boot/dts/omap5-igep0050.dts
+++ b/arch/arm/boot/dts/ti/omap/omap5-igep0050.dts
@@ -85,14 +85,14 @@
 };
 
 &omap5_pmx_core {
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)	/* i2c4_scl */
 			OMAP5_IOPAD(0x0fa, PIN_INPUT | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
 
-	power_button_pin: pinctrl_power_button_pin {
+	power_button_pin: power-button-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x086, PIN_INPUT | MUX_MODE6)	/* gpio4_118 */
 		>;
@@ -128,7 +128,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@3 {
+		ethernet: ethernet@3 {
 			compatible = "usb424,7500";
 			reg = <3>;
 		};
diff --git a/arch/arm/boot/dts/omap5-l4-abe.dtsi b/arch/arm/boot/dts/ti/omap/omap5-l4-abe.dtsi
index 23aa90716f7f..97b0c3b5f573 100644
--- a/arch/arm/boot/dts/omap5-l4-abe.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap5-l4-abe.dtsi
@@ -1,14 +1,16 @@
 &l4_abe {						/* 0x40100000 */
-	compatible = "ti,omap5-l4-abe", "simple-bus";
+	compatible = "ti,omap5-l4-abe", "simple-pm-bus";
 	reg = <0x40100000 0x400>,
 	      <0x40100400 0x400>;
 	reg-names = "la", "ap";
+	power-domains = <&prm_abe>;
+	/* OMAP5_L4_ABE_CLKCTRL is read-only */
 	#address-cells = <1>;
 	#size-cells = <1>;
 	ranges = <0x00000000 0x40100000 0x100000>,	/* segment 0 */
 		 <0x49000000 0x49000000 0x100000>;
 	segment@0 {					/* 0x40100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges =
@@ -107,6 +109,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49022000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP1_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -140,6 +144,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49024000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP2_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -173,6 +179,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49026000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP3_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -203,7 +211,6 @@
 
 		target-module@2e000 {			/* 0x4012e000, ap 12 0c.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "dmic";
 			reg = <0x2e000 0x4>,
 			      <0x2e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -244,7 +251,6 @@
 
 		mcpdm_module: target-module@32000 {	/* 0x40132000, ap 16 10.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "mcpdm";
 			reg = <0x32000 0x4>,
 			      <0x32010 0x4>;
 			reg-names = "rev", "sysc";
@@ -279,7 +285,6 @@
 
 		target-module@38000 {			/* 0x40138000, ap 18 12.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer5";
 			reg = <0x38000 0x4>,
 			      <0x38010 0x4>;
 			reg-names = "rev", "sysc";
@@ -301,8 +306,9 @@
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>,
 				      <0x49038000 0x80>;
-				clocks = <&abe_clkctrl OMAP5_TIMER5_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP5_TIMER5_CLKCTRL 24>,
+					 <&dss_syc_gfclk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 				ti,timer-pwm;
@@ -311,7 +317,6 @@
 
 		target-module@3a000 {			/* 0x4013a000, ap 20 14.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer6";
 			reg = <0x3a000 0x4>,
 			      <0x3a010 0x4>;
 			reg-names = "rev", "sysc";
@@ -333,8 +338,9 @@
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>,
 				      <0x4903a000 0x80>;
-				clocks = <&abe_clkctrl OMAP5_TIMER6_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP5_TIMER6_CLKCTRL 24>,
+					 <&dss_syc_gfclk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 				ti,timer-pwm;
@@ -343,7 +349,6 @@
 
 		target-module@3c000 {			/* 0x4013c000, ap 22 16.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer7";
 			reg = <0x3c000 0x4>,
 			      <0x3c010 0x4>;
 			reg-names = "rev", "sysc";
@@ -365,8 +370,9 @@
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>,
 				      <0x4903c000 0x80>;
-				clocks = <&abe_clkctrl OMAP5_TIMER7_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP5_TIMER7_CLKCTRL 24>,
+					 <&dss_syc_gfclk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 			};
@@ -374,7 +380,6 @@
 
 		target-module@3e000 {			/* 0x4013e000, ap 24 18.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer8";
 			reg = <0x3e000 0x4>,
 			      <0x3e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -396,8 +401,9 @@
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>,
 				      <0x4903e000 0x80>;
-				clocks = <&abe_clkctrl OMAP5_TIMER8_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&abe_clkctrl OMAP5_TIMER8_CLKCTRL 24>,
+					 <&dss_syc_gfclk_div>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-dsp;
 				ti,timer-pwm;
@@ -432,8 +438,20 @@
 		};
 
 		target-module@f1000 {			/* 0x401f1000, ap 32 20.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0xf1000 0x4>,
+			      <0xf1010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			/* Domains (V, P, C): iva, abe_pwrdm, abe_clkdm */
+			clocks = <&abe_clkctrl OMAP5_AESS_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0xf1000 0x1000>,
diff --git a/arch/arm/boot/dts/omap5-l4.dtsi b/arch/arm/boot/dts/ti/omap/omap5-l4.dtsi
index 25aacf1ba708..3b505fe415ed 100644
--- a/arch/arm/boot/dts/omap5-l4.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap5-l4.dtsi
@@ -1,5 +1,8 @@
 &l4_cfg {						/* 0x4a000000 */
-	compatible = "ti,omap5-l4-cfg", "simple-bus";
+	compatible = "ti,omap5-l4-cfg", "simple-pm-bus";
+	power-domains = <&prm_core>;
+	clocks = <&l4cfg_clkctrl OMAP5_L4_CFG_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4a000000 0x800>,
 	      <0x4a000800 0x800>,
 	      <0x4a001000 0x1000>;
@@ -15,7 +18,7 @@
 		 <0x00300000 0x4a300000 0x080000>;	/* segment 6 */
 
 	segment@0 {					/* 0x4a000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -167,7 +170,6 @@
 
 		target-module@20000 {			/* 0x4a020000, ap 109 08.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_otg_ss";
 			reg = <0x20000 0x4>,
 			      <0x20010 0x4>;
 			reg-names = "rev", "sysc";
@@ -195,7 +197,7 @@
 				#size-cells = <1>;
 				utmi-mode = <2>;
 				ranges = <0 0 0x20000>;
-				dwc3: dwc3@10000 {
+				dwc3: usb@10000 {
 					compatible = "snps,dwc3";
 					reg = <0x10000 0x10000>;
 					interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
@@ -213,7 +215,6 @@
 
 		target-module@56000 {			/* 0x4a056000, ap 7 02.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "dma_system";
 			reg = <0x56000 0x4>,
 			      <0x5602c 0x4>,
 			      <0x56028 0x4>;
@@ -237,7 +238,7 @@
 			ranges = <0x0 0x56000 0x1000>;
 
 			sdma: dma-controller@0 {
-				compatible = "ti,omap4430-sdma";
+				compatible = "ti,omap4430-sdma", "ti,omap-sdma";
 				reg = <0x0 0x1000>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
@@ -270,7 +271,6 @@
 
 		target-module@62000 {			/* 0x4a062000, ap 11 0e.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "usb_tll_hs";
 			reg = <0x62000 0x4>,
 			      <0x62010 0x4>,
 			      <0x62014 0x4>;
@@ -299,7 +299,6 @@
 
 		target-module@64000 {			/* 0x4a064000, ap 71 1e.0 */
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			ti,hwmods = "usb_host_hs";
 			reg = <0x64000 0x4>,
 			      <0x64010 0x4>;
 			reg-names = "rev", "sysc";
@@ -349,7 +348,6 @@
 
 		target-module@66000 {			/* 0x4a066000, ap 23 0a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "mmu_dsp";
 			reg = <0x66000 0x4>,
 			      <0x66010 0x4>,
 			      <0x66014 0x4>;
@@ -364,12 +362,18 @@
 			/* Domains (V, P, C): mm, dsp_pwrdm, dsp_clkdm */
 			clocks = <&dsp_clkctrl OMAP5_MMU_DSP_CLKCTRL 0>;
 			clock-names = "fck";
+			resets = <&prm_dsp 1>;
+			reset-names = "rstctrl";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x66000 0x1000>;
 
-			/* mmu_dsp cannot be moved before reset driver */
-			status = "disabled";
+			mmu_dsp: mmu@0 {
+				compatible = "ti,omap4-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+			};
 		};
 
 		target-module@70000 {			/* 0x4a070000, ap 79 2e.0 */
@@ -390,7 +394,7 @@
 	};
 
 	segment@80000 {					/* 0x4a080000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00059000 0x000d9000 0x001000>,	/* ap 13 */
@@ -430,7 +434,6 @@
 
 		target-module@0 {			/* 0x4a080000, ap 83 28.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "ocp2scp1";
 			reg = <0x0 0x4>,
 			      <0x10 0x4>,
 			      <0x14 0x4>;
@@ -479,7 +482,7 @@
 				clocks = <&usb_phy_cm_clk32k>,
 				<&sys_clkin>,
 				<&l3init_clkctrl OMAP5_USB_OTG_SS_CLKCTRL 8>;
-				clock-names =	"wkupclk",
+				clock-names = "wkupclk",
 				"sysclk",
 				"refclk";
 				#phy-cells = <0>;
@@ -488,7 +491,6 @@
 
 		target-module@10000 {			/* 0x4a090000, ap 89 36.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "ocp2scp3";
 			reg = <0x10000 0x4>,
 			      <0x10010 0x4>,
 			      <0x10014 0x4>;
@@ -614,11 +616,11 @@
 				#mbox-cells = <1>;
 				ti,mbox-num-users = <3>;
 				ti,mbox-num-fifos = <8>;
-				mbox_ipu: mbox_ipu {
+				mbox_ipu: mbox-ipu {
 					ti,mbox-tx = <0 0 0>;
 					ti,mbox-rx = <1 0 0>;
 				};
-				mbox_dsp: mbox_dsp {
+				mbox_dsp: mbox-dsp {
 					ti,mbox-tx = <3 0 0>;
 					ti,mbox-rx = <2 0 0>;
 				};
@@ -627,7 +629,6 @@
 
 		target-module@76000 {			/* 0x4a0f6000, ap 27 0c.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "spinlock";
 			reg = <0x76000 0x4>,
 			      <0x76010 0x4>,
 			      <0x76014 0x4>;
@@ -656,7 +657,7 @@
 	};
 
 	segment@100000 {					/* 0x4a100000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00002000 0x00102000 0x001000>,	/* ap 59 */
@@ -693,22 +694,44 @@
 		};
 
 		target-module@40000 {			/* 0x4a140000, ap 101 16.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
-			#address-cells = <1>;
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x400fc 4>,
+			      <0x41100 4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			power-domains = <&prm_l3init>;
+			clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 0>;
+			clock-names = "fck";
 			#size-cells = <1>;
+			#address-cells = <1>;
 			ranges = <0x0 0x40000 0x10000>;
+
+			sata: sata@0 {
+				compatible = "snps,dwc-ahci";
+				reg = <0 0x1100>, <0x1100 0x8>;
+				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&sata_phy>;
+				phy-names = "sata-phy";
+				clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>;
+				ports-implemented = <0x1>;
+			};
 		};
 	};
 
 	segment@180000 {					/* 0x4a180000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 
 	segment@200000 {					/* 0x4a200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0001e000 0x0021e000 0x001000>,	/* ap 29 */
@@ -914,20 +937,23 @@
 	};
 
 	segment@280000 {					/* 0x4a280000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 
 	segment@300000 {					/* 0x4a300000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 };
 
 &l4_per {						/* 0x48000000 */
-	compatible = "ti,omap5-l4-per", "simple-bus";
+	compatible = "ti,omap5-l4-per", "simple-pm-bus";
+	power-domains = <&prm_core>;
+	clocks = <&l4per_clkctrl OMAP5_L4_PER_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x48000000 0x800>,
 	      <0x48000800 0x800>,
 	      <0x48001000 0x400>,
@@ -941,7 +967,7 @@
 		 <0x00200000 0x48200000 0x200000>;	/* segment 1 */
 
 	segment@0 {					/* 0x48000000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -1002,6 +1028,7 @@
 			 <0x00090000 0x00090000 0x002000>,	/* ap 55 */
 			 <0x00092000 0x00092000 0x001000>,	/* ap 56 */
 			 <0x000a4000 0x000a4000 0x001000>,	/* ap 57 */
+			 <0x000a5000 0x000a5000 0x001000>,
 			 <0x000a6000 0x000a6000 0x001000>,	/* ap 58 */
 			 <0x000a8000 0x000a8000 0x004000>,	/* ap 59 */
 			 <0x000ac000 0x000ac000 0x001000>,	/* ap 60 */
@@ -1061,7 +1088,6 @@
 
 		target-module@32000 {			/* 0x48032000, ap 5 3e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer2";
 			reg = <0x32000 0x4>,
 			      <0x32010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1081,15 +1107,15 @@
 			timer2: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl OMAP5_TIMER2_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl OMAP5_TIMER2_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@34000 {			/* 0x48034000, ap 7 46.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer3";
 			reg = <0x34000 0x4>,
 			      <0x34010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1109,15 +1135,15 @@
 			timer3: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl OMAP5_TIMER3_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl OMAP5_TIMER3_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@36000 {			/* 0x48036000, ap 9 4e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer4";
 			reg = <0x36000 0x4>,
 			      <0x36010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1137,15 +1163,15 @@
 			timer4: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl OMAP5_TIMER4_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl OMAP5_TIMER4_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		target-module@3e000 {			/* 0x4803e000, ap 11 56.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer9";
 			reg = <0x3e000 0x4>,
 			      <0x3e010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1165,8 +1191,9 @@
 			timer9: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl OMAP5_TIMER9_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl OMAP5_TIMER9_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 			};
@@ -1713,7 +1740,6 @@
 
 		target-module@86000 {			/* 0x48086000, ap 41 5e.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer10";
 			reg = <0x86000 0x4>,
 			      <0x86010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1733,8 +1759,9 @@
 			timer10: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl OMAP5_TIMER10_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl OMAP5_TIMER10_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 			};
@@ -1742,7 +1769,6 @@
 
 		target-module@88000 {			/* 0x48088000, ap 43 66.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer11";
 			reg = <0x88000 0x4>,
 			      <0x88010 0x4>;
 			reg-names = "rev", "sysc";
@@ -1762,19 +1788,34 @@
 			timer11: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&l4per_clkctrl OMAP5_TIMER11_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&l4per_clkctrl OMAP5_TIMER11_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-pwm;
 			};
 		};
 
-		target-module@90000 {			/* 0x48090000, ap 55 1a.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+		rng_target: target-module@90000 {	/* 0x48090000, ap 55 1a.0 */
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x91fe0 0x4>,
+			      <0x91fe4 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-mask = <(SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl OMAP5_RNG_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x90000 0x2000>;
+
+			rng: rng@0 {
+				compatible = "ti,omap4-rng";
+				reg = <0x0 0x2000>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			};
 		};
 
 		target-module@98000 {			/* 0x48098000, ap 47 08.0 */
@@ -1899,6 +1940,36 @@
 				 <0x00001000 0x000a5000 0x00001000>;
 		};
 
+		des_target: target-module@a5000 {	/* 0x480a5000 */
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0xa5030 0x4>,
+			      <0xa5034 0x4>,
+			      <0xa5038 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl OMAP5_DES3DES_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xa5000 0x00001000>;
+			status = "disabled";
+
+			des: des@0 {
+				compatible = "ti,omap4-des";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 117>, <&sdma 116>;
+				dma-names = "tx", "rx";
+			};
+		};
+
 		target-module@a8000 {			/* 0x480a8000, ap 59 2a.0 */
 			compatible = "ti,sysc";
 			status = "disabled";
@@ -2105,14 +2176,17 @@
 	};
 
 	segment@200000 {					/* 0x48200000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 	};
 };
 
 &l4_wkup {						/* 0x4ae00000 */
-	compatible = "ti,omap5-l4-wkup", "simple-bus";
+	compatible = "ti,omap5-l4-wkup", "simple-pm-bus";
+	power-domains = <&prm_wkupaon>;
+	clocks = <&wkupaon_clkctrl OMAP5_L4_WKUP_CLKCTRL 0>;
+	clock-names = "fck";
 	reg = <0x4ae00000 0x800>,
 	      <0x4ae00800 0x800>,
 	      <0x4ae01000 0x1000>;
@@ -2124,7 +2198,7 @@
 		 <0x00020000 0x4ae20000 0x010000>;	/* segment 2 */
 
 	segment@0 {					/* 0x4ae00000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00000000 0x000800>,	/* ap 0 */
@@ -2141,7 +2215,6 @@
 
 		target-module@4000 {			/* 0x4ae04000, ap 17 20.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "counter_32k";
 			reg = <0x4000 0x4>,
 			      <0x4010 0x4>;
 			reg-names = "rev", "sysc";
@@ -2254,7 +2327,7 @@
 	};
 
 	segment@10000 {					/* 0x4ae10000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x00010000 0x001000>,	/* ap 5 */
@@ -2327,9 +2400,8 @@
 			};
 		};
 
-		target-module@8000 {			/* 0x4ae18000, ap 9 18.0 */
+		timer1_target: target-module@8000 {	/* 0x4ae18000, ap 9 18.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
-			ti,hwmods = "timer1";
 			reg = <0x8000 0x4>,
 			      <0x8010 0x4>;
 			reg-names = "rev", "sysc";
@@ -2349,8 +2421,9 @@
 			timer1: timer@0 {
 				compatible = "ti,omap5430-timer";
 				reg = <0x0 0x80>;
-				clocks = <&wkupaon_clkctrl OMAP5_TIMER1_CLKCTRL 24>;
-				clock-names = "fck";
+				clocks = <&wkupaon_clkctrl OMAP5_TIMER1_CLKCTRL 24>,
+					 <&sys_clkin>;
+				clock-names = "fck", "timer_sys_ck";
 				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 				ti,timer-alwon;
 			};
@@ -2358,7 +2431,6 @@
 
 		target-module@c000 {			/* 0x4ae1c000, ap 11 1c.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
-			ti,hwmods = "kbd";
 			reg = <0xc000 0x4>,
 			      <0xc010 0x4>;
 			reg-names = "rev", "sysc";
@@ -2382,7 +2454,7 @@
 	};
 
 	segment@20000 {					/* 0x4ae20000 */
-		compatible = "simple-bus";
+		compatible = "simple-pm-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00006000 0x00026000 0x001000>,	/* ap 13 */
diff --git a/arch/arm/boot/dts/omap5-sbc-t54.dts b/arch/arm/boot/dts/ti/omap/omap5-sbc-t54.dts
index 657df46251c2..02716fb796bd 100644
--- a/arch/arm/boot/dts/omap5-sbc-t54.dts
+++ b/arch/arm/boot/dts/ti/omap/omap5-sbc-t54.dts
@@ -11,14 +11,14 @@
 };
 
 &omap5_pmx_core {
-	i2c4_pins: pinmux_i2c4_pins {
+	i2c4_pins: i2c4-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x00f8, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
 			OMAP5_IOPAD(0x00fa, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
 		>;
 	};
 
-	mmc1_aux_pins: pinmux_mmc1_aux_pins {
+	mmc1_aux_pins: mmc1-aux-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0174, PIN_INPUT_PULLUP | MUX_MODE6) /* timer5_pwm_evt.gpio8_228 */
 			OMAP5_IOPAD(0x0176, PIN_INPUT_PULLUP | MUX_MODE6) /* timer6_pwm_evt.gpio8_229 */
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/ti/omap/omap5-uevm.dts
index 9441e9a572ad..933de05d3ca1 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/ti/omap/omap5-uevm.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 /dts-v1/;
 
@@ -15,6 +15,26 @@
 		reg = <0 0x80000000 0 0x7f000000>; /* 2032 MB */
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_memory_region: dsp-memory@95000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x95000000 0 0x800000>;
+			reusable;
+			status = "okay";
+		};
+
+		ipu_memory_region: ipu-memory@95800000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x95800000 0 0x3800000>;
+			reusable;
+			status = "okay";
+		};
+	};
+
 	aliases {
 		ethernet = &ethernet;
 	};
@@ -142,20 +162,20 @@
 };
 
 &omap5_pmx_core {
-	evm_keys_pins: pinmux_evm_keys_gpio_pins {
+	evm_keys_pins: evm-keys-gpio-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0b6, PIN_INPUT | MUX_MODE6)	/* gpio3_83 */
 		>;
 	};
 
-	i2c5_pins: pinmux_i2c5_pins {
+	i2c5_pins: i2c5-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1c6, PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
 			OMAP5_IOPAD(0x1c8, PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
 		>;
 	};
 
-	mmc1_pins: pinmux_mmc1_pins {
+	mmc1_pins: mmc1-pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x1d4, PIN_INPUT_PULLUP | MUX_MODE6)	/* gpio5_152 */
 		>;
@@ -189,7 +209,7 @@
 		#size-cells = <0>;
 	};
 
-	ethernet: usbether@3 {
+	ethernet: ethernet@3 {
 		compatible = "usb424,9730";
 		reg = <3>;
 	};
@@ -198,3 +218,17 @@
 &wlcore {
 	compatible = "ti,wl1837";
 };
+
+&dsp {
+	status = "okay";
+	memory-region = <&dsp_memory_region>;
+	ti,timers = <&timer5>;
+	ti,watchdog-timers = <&timer6>;
+};
+
+&ipu {
+	status = "okay";
+	memory-region = <&ipu_memory_region>;
+	ti,timers = <&timer3>;
+	ti,watchdog-timers = <&timer9>, <&timer11>;
+};
diff --git a/arch/arm/boot/dts/ti/omap/omap5.dtsi b/arch/arm/boot/dts/ti/omap/omap5.dtsi
new file mode 100644
index 000000000000..bac6fa838793
--- /dev/null
+++ b/arch/arm/boot/dts/ti/omap/omap5.dtsi
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Based on "omap4.dtsi"
+ */
+
+#include <dt-bindings/bus/ti-sysc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/omap.h>
+#include <dt-bindings/clock/omap5.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	compatible = "ti,omap5";
+	interrupt-parent = <&wakeupgen>;
+	chosen { };
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
+		mmc0 = &mmc1;
+		mmc1 = &mmc2;
+		mmc2 = &mmc3;
+		mmc3 = &mmc4;
+		mmc4 = &mmc5;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+		rproc0 = &dsp;
+		rproc1 = &ipu;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x0>;
+
+			operating-points = <
+				/* kHz    uV */
+				1000000 1060000
+				1500000 1250000
+			>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
+			/* cooling options */
+			#cooling-cells = <2>; /* min followed by max */
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x1>;
+
+			operating-points = <
+				/* kHz    uV */
+				1000000 1060000
+				1500000 1250000
+			>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
+			/* cooling options */
+			#cooling-cells = <2>; /* min followed by max */
+		};
+	};
+
+	thermal-zones {
+		#include "omap4-cpu-thermal.dtsi"
+		#include "omap5-gpu-thermal.dtsi"
+		#include "omap5-core-thermal.dtsi"
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		/* PPI secure/nonsecure IRQ */
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&gic>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	/*
+	 * Needed early by omap4_sram_init() for barrier, do not move to l3
+	 * interconnect as simple-pm-bus probes at module_init() time.
+	 */
+	ocmcram: sram@40300000 {
+		compatible = "mmio-sram";
+		reg = <0 0x40300000 0 0x20000>; /* 128k */
+	};
+
+	gic: interrupt-controller@48211000 {
+		compatible = "arm,cortex-a15-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0 0x48211000 0 0x1000>,
+		      <0 0x48212000 0 0x2000>,
+		      <0 0x48214000 0 0x2000>,
+		      <0 0x48216000 0 0x2000>;
+		interrupt-parent = <&gic>;
+	};
+
+	wakeupgen: interrupt-controller@48281000 {
+		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0 0x48281000 0 0x1000>;
+		interrupt-parent = <&gic>;
+	};
+
+	/*
+	 * XXX: Use a flat representation of the OMAP3 interconnect.
+	 * The real OMAP interconnect network is quite complex.
+	 * Since it will not bring real advantage to represent that in DT for
+	 * the moment, just use a fake OCP bus entry to represent the whole bus
+	 * hierarchy.
+	 */
+	ocp {
+		compatible = "simple-pm-bus";
+		power-domains = <&prm_core>;
+		clocks = <&l3main1_clkctrl OMAP5_L3_MAIN_1_CLKCTRL 0>,
+			 <&l3main2_clkctrl OMAP5_L3_MAIN_2_CLKCTRL 0>,
+			 <&l3instr_clkctrl OMAP5_L3_MAIN_3_CLKCTRL 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xc0000000>;
+		dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>;
+
+		l3-noc@44000000 {
+			compatible = "ti,omap5-l3-noc";
+			reg = <0x44000000 0x2000>,
+			      <0x44800000 0x3000>,
+			      <0x45000000 0x4000>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		l4_wkup: interconnect@4ae00000 {
+		};
+
+		l4_cfg: interconnect@4a000000 {
+		};
+
+		l4_per: interconnect@48000000 {
+		};
+
+		target-module@48210000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			power-domains = <&prm_mpu>;
+			clocks = <&mpu_clkctrl OMAP5_MPU_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48210000 0x1f0000>;
+
+			mpu {
+				compatible = "ti,omap4-mpu";
+				sram = <&ocmcram>;
+			};
+		};
+
+		l4_abe: interconnect@40100000 {
+		};
+
+		target-module@50000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x50000000 4>,
+			      <0x50000010 4>,
+			      <0x50000014 4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			ti,no-idle-on-init;
+			clocks = <&l3main2_clkctrl OMAP5_L3_MAIN_2_GPMC_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
+				 <0x00000000 0x00000000 0x40000000>; /* data */
+
+			gpmc: gpmc@50000000 {
+				compatible = "ti,omap4430-gpmc";
+				reg = <0x50000000 0x1000>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 4>;
+				dma-names = "rxtx";
+				gpmc,num-cs = <8>;
+				gpmc,num-waitpins = <4>;
+				clock-names = "fck";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		target-module@55082000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x55082000 0x4>,
+			      <0x55082010 0x4>,
+			      <0x55082014 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+					 SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			clocks = <&ipu_clkctrl OMAP5_MMU_IPU_CLKCTRL 0>;
+			clock-names = "fck";
+			resets = <&prm_core 2>;
+			reset-names = "rstctrl";
+			ranges = <0x0 0x55082000 0x100>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			mmu_ipu: mmu@0 {
+				compatible = "ti,omap4-iommu";
+				reg = <0x0 0x100>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+				#iommu-cells = <0>;
+				ti,iommu-bus-err-back;
+			};
+		};
+
+		dsp: dsp {
+			compatible = "ti,omap5-dsp";
+			ti,bootreg = <&scm_conf 0x304 0>;
+			iommus = <&mmu_dsp>;
+			resets = <&prm_dsp 0>;
+			clocks = <&dsp_clkctrl OMAP5_MMU_DSP_CLKCTRL 0>;
+			firmware-name = "omap5-dsp-fw.xe64T";
+			mboxes = <&mailbox &mbox_dsp>;
+			status = "disabled";
+		};
+
+		ipu: ipu@55020000 {
+			compatible = "ti,omap5-ipu";
+			reg = <0x55020000 0x10000>;
+			reg-names = "l2ram";
+			iommus = <&mmu_ipu>;
+			resets = <&prm_core 0>, <&prm_core 1>;
+			clocks = <&ipu_clkctrl OMAP5_MMU_IPU_CLKCTRL 0>;
+			firmware-name = "omap5-ipu-fw.xem4";
+			mboxes = <&mailbox &mbox_ipu>;
+			status = "disabled";
+		};
+
+		target-module@4e000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4e000000 0x4>,
+			      <0x4e000010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ranges = <0x0 0x4e000000 0x2000000>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+
+			dmm@0 {
+				compatible = "ti,omap5-dmm";
+				reg = <0 0x800>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		target-module@4c000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			reg = <0x4c000000 0x4>;
+			reg-names = "rev";
+			clocks = <&emif_clkctrl OMAP5_EMIF1_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4c000000 0x1000000>;
+
+			emif1: emif@0 {
+				compatible = "ti,emif-4d5";
+				reg = <0 0x400>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phy-type = <2>; /* DDR PHY type: Intelli PHY */
+				hw-caps-read-idle-ctrl;
+				hw-caps-ll-interface;
+				hw-caps-temp-alert;
+			};
+		};
+
+		target-module@4d000000 {
+			compatible = "ti,sysc-omap4-simple", "ti,sysc";
+			reg = <0x4d000000 0x4>;
+			reg-names = "rev";
+			clocks = <&emif_clkctrl OMAP5_EMIF2_CLKCTRL 0>;
+			clock-names = "fck";
+			ti,no-idle;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4d000000 0x1000000>;
+
+			emif2: emif@0 {
+				compatible = "ti,emif-4d5";
+				reg = <0 0x400>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				phy-type = <2>; /* DDR PHY type: Intelli PHY */
+				hw-caps-read-idle-ctrl;
+				hw-caps-ll-interface;
+				hw-caps-temp-alert;
+			};
+		};
+
+		aes1_target: target-module@4b501000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4b501080 0x4>,
+			      <0x4b501084 0x4>,
+			      <0x4b501088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl OMAP5_AES1_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b501000 0x1000>;
+
+			aes1: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 111>, <&sdma 110>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		aes2_target: target-module@4b701000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x4b701080 0x4>,
+			      <0x4b701084 0x4>,
+			      <0x4b701088 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>,
+					<SYSC_IDLE_SMART_WKUP>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl OMAP5_AES2_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b701000 0x1000>;
+
+			aes2: aes@0 {
+				compatible = "ti,omap4-aes";
+				reg = <0 0xa0>;
+				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 114>, <&sdma 113>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		sham_target: target-module@4b100000 {
+			compatible = "ti,sysc-omap3-sham", "ti,sysc";
+			reg = <0x4b100100 0x4>,
+			      <0x4b100110 0x4>,
+			      <0x4b100114 0x4>;
+			reg-names = "rev", "sysc", "syss";
+			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+					 SYSC_OMAP2_AUTOIDLE)>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,syss-mask = <1>;
+			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
+			clocks = <&l4sec_clkctrl OMAP5_SHA2MD5_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x4b100000 0x1000>;
+
+			sham: sham@0 {
+				compatible = "ti,omap4-sham";
+				reg = <0 0x300>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&sdma 119>;
+				dma-names = "rx";
+			};
+		};
+
+		bandgap: bandgap@4a0021e0 {
+			reg = <0x4a0021e0 0xc
+			       0x4a00232c 0xc
+			       0x4a002380 0x2c
+			       0x4a0023C0 0x3c>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			compatible = "ti,omap5430-bandgap";
+
+			#thermal-sensor-cells = <1>;
+		};
+
+		target-module@56000000 {
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x5600fe00 0x4>,
+			      <0x5600fe10 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&gpu_clkctrl OMAP5_GPU_CLKCTRL 0>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x56000000 0x2000000>;
+
+			/*
+			 * Closed source PowerVR driver, no child device
+			 * binding or driver in mainline
+			 */
+		};
+
+		target-module@58000000 {
+			compatible = "ti,sysc-omap2", "ti,sysc";
+			reg = <0x58000000 4>,
+			      <0x58000014 4>;
+			reg-names = "rev", "syss";
+			ti,syss-mask = <1>;
+			power-domains = <&prm_dss>;
+			clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 0>,
+				 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
+				 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>,
+				 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 11>;
+			clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x58000000 0x1000000>;
+
+			dss: dss@0 {
+				compatible = "ti,omap5-dss";
+				reg = <0 0x80>;
+				status = "disabled";
+				clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0 0x1000000>;
+
+				target-module@1000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x1000 0x4>,
+					      <0x1010 0x4>,
+					      <0x1014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-midle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x1000 0x1000>;
+
+					dispc@0 {
+						compatible = "ti,omap5-dispc";
+						reg = <0 0x1000>;
+						interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+						clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
+						clock-names = "fck";
+					};
+				};
+
+				target-module@2000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x2000 0x4>,
+					      <0x2010 0x4>,
+					      <0x2014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x2000 0x1000>;
+
+					rfbi: encoder@0  {
+						compatible = "ti,omap5-rfbi";
+						reg = <0 0x100>;
+						status = "disabled";
+						clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, <&l3_iclk_div>;
+						clock-names = "fck", "ick";
+					};
+				};
+
+				target-module@4000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x4000 0x4>,
+					      <0x4010 0x4>,
+					      <0x4014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x4000 0x1000>;
+
+					dsi1: encoder@0 {
+						compatible = "ti,omap5-dsi";
+						reg = <0 0x200>,
+						      <0x200 0x40>,
+						      <0x300 0x40>;
+						reg-names = "proto", "phy", "pll";
+						interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>,
+							 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+
+				target-module@9000 {
+					compatible = "ti,sysc-omap2", "ti,sysc";
+					reg = <0x9000 0x4>,
+					      <0x9010 0x4>,
+					      <0x9014 0x4>;
+					reg-names = "rev", "sysc", "syss";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>;
+					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
+							 SYSC_OMAP2_ENAWAKEUP |
+							 SYSC_OMAP2_SOFTRESET |
+							 SYSC_OMAP2_AUTOIDLE)>;
+					ti,syss-mask = <1>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x9000 0x1000>;
+
+					dsi2: encoder@0 {
+						compatible = "ti,omap5-dsi";
+						reg = <0 0x200>,
+						      <0x200 0x40>,
+						      <0x300 0x40>;
+						reg-names = "proto", "phy", "pll";
+						interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>,
+							 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+
+				target-module@40000 {
+					compatible = "ti,sysc-omap4", "ti,sysc";
+					reg = <0x40000 0x4>,
+					      <0x40010 0x4>;
+					reg-names = "rev", "sysc";
+					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+							<SYSC_IDLE_NO>,
+							<SYSC_IDLE_SMART>,
+							<SYSC_IDLE_SMART_WKUP>;
+					ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
+					clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
+						 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
+					clock-names = "fck", "dss_clk";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x40000 0x40000>;
+
+					hdmi: encoder@0 {
+						compatible = "ti,omap5-hdmi";
+						reg = <0 0x200>,
+						      <0x200 0x80>,
+						      <0x300 0x80>,
+						      <0x20000 0x19000>;
+						reg-names = "wp", "pll", "phy", "core";
+						interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+						status = "disabled";
+						clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
+							 <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
+						clock-names = "fck", "sys_clk";
+						dmas = <&sdma 76>;
+						dma-names = "audio_tx";
+					};
+				};
+			};
+		};
+
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07cdc 0x8>, <0x4ae06014 0x4>,
+			      <0x4a0021c4 0x8>, <0x4ae0c318 0x4>;
+			reg-names = "base-address", "int-address",
+				    "efuse-address", "ldo-address";
+			ti,tranxdone-status-mask = <0x80>;
+			/* LDOVBBMPU_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBMPU_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1060000		0	0x0	0 0x02000000 0x01F00000
+			1250000		0	0x4	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_mm: regulator-abb-mm {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_mm";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
+			      <0x4a0021a4 0x8>, <0x4ae0c314 0x4>;
+			reg-names = "base-address", "int-address",
+				    "efuse-address", "ldo-address";
+			ti,tranxdone-status-mask = <0x80000000>;
+			/* LDOVBBMM_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBMM_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1025000		0	0x0	0 0x02000000 0x01F00000
+			1120000		0	0x4	0 0x02000000 0x01F00000
+			>;
+		};
+	};
+};
+
+&cpu_thermal {
+	polling-delay = <500>; /* milliseconds */
+	coefficients = <65 (-1791)>;
+};
+
+#include "omap5-l4.dtsi"
+#include "omap54xx-clocks.dtsi"
+
+&gpu_thermal {
+	coefficients = <117 (-2992)>;
+};
+
+&core_thermal {
+	coefficients = <0 2000>;
+};
+
+#include "omap5-l4-abe.dtsi"
+#include "omap54xx-clocks.dtsi"
+
+&prm {
+	prm_mpu: prm@300 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x300 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dsp: prm@400 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x400 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_abe: prm@500 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x500 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_coreaon: prm@600 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x600 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_core: prm@700 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x700 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_iva: prm@1200 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1200 0x100>;
+		#reset-cells = <1>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_cam: prm@1300 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1300 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_dss: prm@1400 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1400 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_gpu: prm@1500 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1500 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_l3init: prm@1600 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1600 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_custefuse: prm@1700 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1700 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_wkupaon: prm@1800 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1800 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_emu: prm@1a00 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1a00 0x100>;
+		#power-domain-cells = <0>;
+	};
+
+	prm_device: prm@1c00 {
+		compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst";
+		reg = <0x1c00 0x100>;
+		#reset-cells = <1>;
+	};
+};
+
+/* Preferred always-on timer for clockevent */
+&timer1_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&wkupaon_clkctrl OMAP5_TIMER1_CLKCTRL 24>;
+		assigned-clock-parents = <&sys_32k_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap54xx-clocks.dtsi b/arch/arm/boot/dts/ti/omap/omap54xx-clocks.dtsi
index 4791834dacb2..5cf3b0e78c15 100644
--- a/arch/arm/boot/dts/omap54xx-clocks.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap54xx-clocks.dtsi
@@ -8,12 +8,14 @@
 	pad_clks_src_ck: pad_clks_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pad_clks_src_ck";
 		clock-frequency = <12000000>;
 	};
 
 	pad_clks_ck: pad_clks_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "pad_clks_ck";
 		clocks = <&pad_clks_src_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0108>;
@@ -22,18 +24,21 @@
 	secure_32k_clk_src_ck: secure_32k_clk_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "secure_32k_clk_src_ck";
 		clock-frequency = <32768>;
 	};
 
 	slimbus_src_clk: slimbus_src_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "slimbus_src_clk";
 		clock-frequency = <12000000>;
 	};
 
 	slimbus_clk: slimbus_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "slimbus_clk";
 		clocks = <&slimbus_src_clk>;
 		ti,bit-shift = <10>;
 		reg = <0x0108>;
@@ -42,66 +47,77 @@
 	sys_32k_ck: sys_32k_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_32k_ck";
 		clock-frequency = <32768>;
 	};
 
 	virt_12000000_ck: virt_12000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_12000000_ck";
 		clock-frequency = <12000000>;
 	};
 
 	virt_13000000_ck: virt_13000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_13000000_ck";
 		clock-frequency = <13000000>;
 	};
 
 	virt_16800000_ck: virt_16800000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_16800000_ck";
 		clock-frequency = <16800000>;
 	};
 
 	virt_19200000_ck: virt_19200000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
 	virt_26000000_ck: virt_26000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
 	virt_27000000_ck: virt_27000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_27000000_ck";
 		clock-frequency = <27000000>;
 	};
 
 	virt_38400000_ck: virt_38400000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_38400000_ck";
 		clock-frequency = <38400000>;
 	};
 
 	xclk60mhsp1_ck: xclk60mhsp1_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp1_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60mhsp2_ck: xclk60mhsp2_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp2_ck";
 		clock-frequency = <60000000>;
 	};
 
 	dpll_abe_ck: dpll_abe_ck@1e0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-m4xen-clock";
+		clock-output-names = "dpll_abe_ck";
 		clocks = <&abe_dpll_clk_mux>, <&abe_dpll_bypass_clk_mux>;
 		reg = <0x01e0>, <0x01e4>, <0x01ec>, <0x01e8>;
 	};
@@ -109,12 +125,14 @@
 	dpll_abe_x2_ck: dpll_abe_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_abe_x2_ck";
 		clocks = <&dpll_abe_ck>;
 	};
 
 	dpll_abe_m2x2_ck: dpll_abe_m2x2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x01f0>;
@@ -124,6 +142,7 @@
 	abe_24m_fclk: abe_24m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "abe_24m_fclk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
@@ -132,6 +151,7 @@
 	abe_clk: abe_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_clk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x0108>;
@@ -141,6 +161,7 @@
 	abe_iclk: abe_iclk@528 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_iclk";
 		clocks = <&aess_fclk>;
 		ti,bit-shift = <24>;
 		reg = <0x0528>;
@@ -150,6 +171,7 @@
 	abe_lp_clk_div: abe_lp_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "abe_lp_clk_div";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -158,6 +180,7 @@
 	dpll_abe_m3x2_ck: dpll_abe_m3x2_ck@1f4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m3x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x01f4>;
@@ -167,6 +190,7 @@
 	dpll_core_byp_mux: dpll_core_byp_mux@12c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_core_byp_mux";
 		clocks = <&sys_clkin>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x012c>;
@@ -175,6 +199,7 @@
 	dpll_core_ck: dpll_core_ck@120 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin>, <&dpll_core_byp_mux>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
@@ -182,12 +207,14 @@
 	dpll_core_x2_ck: dpll_core_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
 	dpll_core_h21x2_ck: dpll_core_h21x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h21x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0150>;
@@ -197,6 +224,7 @@
 	c2c_fclk: c2c_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "c2c_fclk";
 		clocks = <&dpll_core_h21x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -205,6 +233,7 @@
 	c2c_iclk: c2c_iclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "c2c_iclk";
 		clocks = <&c2c_fclk>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -213,6 +242,7 @@
 	dpll_core_h11x2_ck: dpll_core_h11x2_ck@138 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h11x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0138>;
@@ -222,6 +252,7 @@
 	dpll_core_h12x2_ck: dpll_core_h12x2_ck@13c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h12x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x013c>;
@@ -231,6 +262,7 @@
 	dpll_core_h13x2_ck: dpll_core_h13x2_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h13x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0140>;
@@ -240,6 +272,7 @@
 	dpll_core_h14x2_ck: dpll_core_h14x2_ck@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h14x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0144>;
@@ -249,6 +282,7 @@
 	dpll_core_h22x2_ck: dpll_core_h22x2_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h22x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0154>;
@@ -258,6 +292,7 @@
 	dpll_core_h23x2_ck: dpll_core_h23x2_ck@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h23x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0158>;
@@ -267,6 +302,7 @@
 	dpll_core_h24x2_ck: dpll_core_h24x2_ck@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h24x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x015c>;
@@ -276,6 +312,7 @@
 	dpll_core_m2_ck: dpll_core_m2_ck@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m2_ck";
 		clocks = <&dpll_core_ck>;
 		ti,max-div = <31>;
 		reg = <0x0130>;
@@ -285,6 +322,7 @@
 	dpll_core_m3x2_ck: dpll_core_m3x2_ck@134 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m3x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0134>;
@@ -294,6 +332,7 @@
 	iva_dpll_hs_clk_div: iva_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "iva_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -302,6 +341,7 @@
 	dpll_iva_byp_mux: dpll_iva_byp_mux@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_iva_byp_mux";
 		clocks = <&sys_clkin>, <&iva_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x01ac>;
@@ -310,6 +350,7 @@
 	dpll_iva_ck: dpll_iva_ck@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_iva_ck";
 		clocks = <&sys_clkin>, <&dpll_iva_byp_mux>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 		assigned-clocks = <&dpll_iva_ck>;
@@ -319,12 +360,14 @@
 	dpll_iva_x2_ck: dpll_iva_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_iva_x2_ck";
 		clocks = <&dpll_iva_ck>;
 	};
 
 	dpll_iva_h11x2_ck: dpll_iva_h11x2_ck@1b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_h11x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x01b8>;
@@ -336,6 +379,7 @@
 	dpll_iva_h12x2_ck: dpll_iva_h12x2_ck@1bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_h12x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x01bc>;
@@ -347,6 +391,7 @@
 	mpu_dpll_hs_clk_div: mpu_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -355,6 +400,7 @@
 	dpll_mpu_ck: dpll_mpu_ck@160 {
 		#clock-cells = <0>;
 		compatible = "ti,omap5-mpu-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin>, <&mpu_dpll_hs_clk_div>;
 		reg = <0x0160>, <0x0164>, <0x016c>, <0x0168>;
 	};
@@ -362,6 +408,7 @@
 	dpll_mpu_m2_ck: dpll_mpu_m2_ck@170 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		reg = <0x0170>;
@@ -371,6 +418,7 @@
 	per_dpll_hs_clk_div: per_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -379,6 +427,7 @@
 	usb_dpll_hs_clk_div: usb_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "usb_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <3>;
@@ -387,6 +436,7 @@
 	l3_iclk_div: l3_iclk_div@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3_iclk_div";
 		ti,max-div = <2>;
 		ti,bit-shift = <4>;
 		reg = <0x100>;
@@ -397,6 +447,7 @@
 	gpu_l3_iclk: gpu_l3_iclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "gpu_l3_iclk";
 		clocks = <&l3_iclk_div>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -405,6 +456,7 @@
 	l4_root_clk_div: l4_root_clk_div@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l4_root_clk_div";
 		ti,max-div = <2>;
 		ti,bit-shift = <8>;
 		reg = <0x100>;
@@ -415,6 +467,7 @@
 	slimbus1_slimbus_clk: slimbus1_slimbus_clk@560 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "slimbus1_slimbus_clk";
 		clocks = <&slimbus_clk>;
 		ti,bit-shift = <11>;
 		reg = <0x0560>;
@@ -423,6 +476,7 @@
 	aess_fclk: aess_fclk@528 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "aess_fclk";
 		clocks = <&abe_clk>;
 		ti,bit-shift = <24>;
 		ti,max-div = <2>;
@@ -432,6 +486,7 @@
 	mcasp_sync_mux_ck: mcasp_sync_mux_ck@540 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "mcasp_sync_mux_ck";
 		clocks = <&abe_24m_fclk>, <&dss_syc_gfclk_div>, <&func_24m_clk>;
 		ti,bit-shift = <26>;
 		reg = <0x0540>;
@@ -440,6 +495,7 @@
 	mcasp_gfclk: mcasp_gfclk@540 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "mcasp_gfclk";
 		clocks = <&mcasp_sync_mux_ck>, <&pad_clks_ck>, <&slimbus_clk>;
 		ti,bit-shift = <24>;
 		reg = <0x0540>;
@@ -448,6 +504,7 @@
 	dummy_ck: dummy_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "dummy_ck";
 		clock-frequency = <0>;
 	};
 };
@@ -455,6 +512,7 @@
 	sys_clkin: sys_clkin@110 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin";
 		clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
 		reg = <0x0110>;
 		ti,index-starts-at-one;
@@ -463,6 +521,7 @@
 	abe_dpll_bypass_clk_mux: abe_dpll_bypass_clk_mux@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_bypass_clk_mux";
 		clocks = <&sys_clkin>, <&sys_32k_ck>;
 		reg = <0x0108>;
 	};
@@ -470,6 +529,7 @@
 	abe_dpll_clk_mux: abe_dpll_clk_mux@10c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_clk_mux";
 		clocks = <&sys_clkin>, <&sys_32k_ck>;
 		reg = <0x010c>;
 	};
@@ -477,6 +537,7 @@
 	custefuse_sys_gfclk_div: custefuse_sys_gfclk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "custefuse_sys_gfclk_div";
 		clocks = <&sys_clkin>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -485,6 +546,7 @@
 	dss_syc_gfclk_div: dss_syc_gfclk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dss_syc_gfclk_div";
 		clocks = <&sys_clkin>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -493,6 +555,7 @@
 	wkupaon_iclk_mux: wkupaon_iclk_mux@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wkupaon_iclk_mux";
 		clocks = <&sys_clkin>, <&abe_lp_clk_div>;
 		reg = <0x0108>;
 	};
@@ -500,6 +563,7 @@
 	l3instr_ts_gclk_div: l3instr_ts_gclk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3instr_ts_gclk_div";
 		clocks = <&wkupaon_iclk_mux>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -511,6 +575,7 @@
 	dpll_per_byp_mux: dpll_per_byp_mux@14c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_per_byp_mux";
 		clocks = <&sys_clkin>, <&per_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x014c>;
@@ -519,6 +584,7 @@
 	dpll_per_ck: dpll_per_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin>, <&dpll_per_byp_mux>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
@@ -526,12 +592,14 @@
 	dpll_per_x2_ck: dpll_per_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_per_x2_ck";
 		clocks = <&dpll_per_ck>;
 	};
 
 	dpll_per_h11x2_ck: dpll_per_h11x2_ck@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h11x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0158>;
@@ -541,6 +609,7 @@
 	dpll_per_h12x2_ck: dpll_per_h12x2_ck@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h12x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x015c>;
@@ -550,6 +619,7 @@
 	dpll_per_h14x2_ck: dpll_per_h14x2_ck@164 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h14x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0164>;
@@ -559,6 +629,7 @@
 	dpll_per_m2_ck: dpll_per_m2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		reg = <0x0150>;
@@ -568,6 +639,7 @@
 	dpll_per_m2x2_ck: dpll_per_m2x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0150>;
@@ -577,6 +649,7 @@
 	dpll_per_m3x2_ck: dpll_per_m3x2_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m3x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0154>;
@@ -586,6 +659,7 @@
 	dpll_unipro1_ck: dpll_unipro1_ck@200 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_unipro1_ck";
 		clocks = <&sys_clkin>, <&sys_clkin>;
 		reg = <0x0200>, <0x0204>, <0x020c>, <0x0208>;
 	};
@@ -593,6 +667,7 @@
 	dpll_unipro1_clkdcoldo: dpll_unipro1_clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_unipro1_clkdcoldo";
 		clocks = <&dpll_unipro1_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -601,6 +676,7 @@
 	dpll_unipro1_m2_ck: dpll_unipro1_m2_ck@210 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_unipro1_m2_ck";
 		clocks = <&dpll_unipro1_ck>;
 		ti,max-div = <127>;
 		reg = <0x0210>;
@@ -610,6 +686,7 @@
 	dpll_unipro2_ck: dpll_unipro2_ck@1c0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_unipro2_ck";
 		clocks = <&sys_clkin>, <&sys_clkin>;
 		reg = <0x01c0>, <0x01c4>, <0x01cc>, <0x01c8>;
 	};
@@ -617,6 +694,7 @@
 	dpll_unipro2_clkdcoldo: dpll_unipro2_clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_unipro2_clkdcoldo";
 		clocks = <&dpll_unipro2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -625,6 +703,7 @@
 	dpll_unipro2_m2_ck: dpll_unipro2_m2_ck@1d0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_unipro2_m2_ck";
 		clocks = <&dpll_unipro2_ck>;
 		ti,max-div = <127>;
 		reg = <0x01d0>;
@@ -634,6 +713,7 @@
 	dpll_usb_byp_mux: dpll_usb_byp_mux@18c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_usb_byp_mux";
 		clocks = <&sys_clkin>, <&usb_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x018c>;
@@ -642,6 +722,7 @@
 	dpll_usb_ck: dpll_usb_ck@180 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
+		clock-output-names = "dpll_usb_ck";
 		clocks = <&sys_clkin>, <&dpll_usb_byp_mux>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
@@ -649,6 +730,7 @@
 	dpll_usb_clkdcoldo: dpll_usb_clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_usb_clkdcoldo";
 		clocks = <&dpll_usb_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -657,6 +739,7 @@
 	dpll_usb_m2_ck: dpll_usb_m2_ck@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_usb_m2_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,max-div = <127>;
 		reg = <0x0190>;
@@ -666,6 +749,7 @@
 	func_128m_clk: func_128m_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_128m_clk";
 		clocks = <&dpll_per_h11x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -674,6 +758,7 @@
 	func_12m_fclk: func_12m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -682,6 +767,7 @@
 	func_24m_clk: func_24m_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -690,6 +776,7 @@
 	func_48m_fclk: func_48m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_48m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -698,6 +785,7 @@
 	func_96m_fclk: func_96m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_96m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -706,6 +794,7 @@
 	l3init_60m_fclk: l3init_60m_fclk@104 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3init_60m_fclk";
 		clocks = <&dpll_usb_m2_ck>;
 		reg = <0x0104>;
 		ti,dividers = <1>, <8>;
@@ -714,6 +803,7 @@
 	iss_ctrlclk: iss_ctrlclk@1320 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "iss_ctrlclk";
 		clocks = <&func_96m_fclk>;
 		ti,bit-shift = <8>;
 		reg = <0x1320>;
@@ -722,6 +812,7 @@
 	lli_txphy_clk: lli_txphy_clk@f20 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "lli_txphy_clk";
 		clocks = <&dpll_unipro1_clkdcoldo>;
 		ti,bit-shift = <8>;
 		reg = <0x0f20>;
@@ -730,6 +821,7 @@
 	lli_txphy_ls_clk: lli_txphy_ls_clk@f20 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "lli_txphy_ls_clk";
 		clocks = <&dpll_unipro1_m2_ck>;
 		ti,bit-shift = <9>;
 		reg = <0x0f20>;
@@ -738,6 +830,7 @@
 	usb_phy_cm_clk32k: usb_phy_cm_clk32k@640 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy_cm_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0640>;
@@ -746,6 +839,7 @@
 	fdif_fclk: fdif_fclk@1328 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "fdif_fclk";
 		clocks = <&dpll_per_h11x2_ck>;
 		ti,bit-shift = <24>;
 		ti,max-div = <2>;
@@ -755,6 +849,7 @@
 	gpu_core_gclk_mux: gpu_core_gclk_mux@1520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_core_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1520>;
@@ -763,6 +858,7 @@
 	gpu_hyd_gclk_mux: gpu_hyd_gclk_mux@1520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_hyd_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>;
 		ti,bit-shift = <25>;
 		reg = <0x1520>;
@@ -771,6 +867,7 @@
 	hsi_fclk: hsi_fclk@1638 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "hsi_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		ti,bit-shift = <24>;
 		ti,max-div = <2>;
@@ -781,6 +878,7 @@
 &cm_core_clockdomains {
 	l3init_clkdm: l3init_clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "l3init_clkdm";
 		clocks = <&dpll_usb_ck>;
 	};
 };
@@ -789,6 +887,7 @@
 	auxclk0_src_gate_ck: auxclk0_src_gate_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk0_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0310>;
@@ -797,6 +896,7 @@
 	auxclk0_src_mux_ck: auxclk0_src_mux_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk0_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0310>;
@@ -805,12 +905,14 @@
 	auxclk0_src_ck: auxclk0_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk0_src_ck";
 		clocks = <&auxclk0_src_gate_ck>, <&auxclk0_src_mux_ck>;
 	};
 
 	auxclk0_ck: auxclk0_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk0_ck";
 		clocks = <&auxclk0_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -820,6 +922,7 @@
 	auxclk1_src_gate_ck: auxclk1_src_gate_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk1_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0314>;
@@ -828,6 +931,7 @@
 	auxclk1_src_mux_ck: auxclk1_src_mux_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk1_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0314>;
@@ -836,12 +940,14 @@
 	auxclk1_src_ck: auxclk1_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk1_src_ck";
 		clocks = <&auxclk1_src_gate_ck>, <&auxclk1_src_mux_ck>;
 	};
 
 	auxclk1_ck: auxclk1_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk1_ck";
 		clocks = <&auxclk1_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -851,6 +957,7 @@
 	auxclk2_src_gate_ck: auxclk2_src_gate_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk2_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0318>;
@@ -859,6 +966,7 @@
 	auxclk2_src_mux_ck: auxclk2_src_mux_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk2_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0318>;
@@ -867,12 +975,14 @@
 	auxclk2_src_ck: auxclk2_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk2_src_ck";
 		clocks = <&auxclk2_src_gate_ck>, <&auxclk2_src_mux_ck>;
 	};
 
 	auxclk2_ck: auxclk2_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk2_ck";
 		clocks = <&auxclk2_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -882,6 +992,7 @@
 	auxclk3_src_gate_ck: auxclk3_src_gate_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk3_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x031c>;
@@ -890,6 +1001,7 @@
 	auxclk3_src_mux_ck: auxclk3_src_mux_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk3_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x031c>;
@@ -898,12 +1010,14 @@
 	auxclk3_src_ck: auxclk3_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk3_src_ck";
 		clocks = <&auxclk3_src_gate_ck>, <&auxclk3_src_mux_ck>;
 	};
 
 	auxclk3_ck: auxclk3_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk3_ck";
 		clocks = <&auxclk3_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -913,6 +1027,7 @@
 	auxclk4_src_gate_ck: auxclk4_src_gate_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk4_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0320>;
@@ -921,6 +1036,7 @@
 	auxclk4_src_mux_ck: auxclk4_src_mux_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk4_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0320>;
@@ -929,12 +1045,14 @@
 	auxclk4_src_ck: auxclk4_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk4_src_ck";
 		clocks = <&auxclk4_src_gate_ck>, <&auxclk4_src_mux_ck>;
 	};
 
 	auxclk4_ck: auxclk4_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk4_ck";
 		clocks = <&auxclk4_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -944,6 +1062,7 @@
 	auxclkreq0_ck: auxclkreq0_ck@210 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq0_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0210>;
@@ -952,6 +1071,7 @@
 	auxclkreq1_ck: auxclkreq1_ck@214 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq1_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0214>;
@@ -960,6 +1080,7 @@
 	auxclkreq2_ck: auxclkreq2_ck@218 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq2_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0218>;
@@ -968,6 +1089,7 @@
 	auxclkreq3_ck: auxclkreq3_ck@21c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq3_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x021c>;
@@ -977,6 +1099,7 @@
 &cm_core_aon {
 	mpu_cm: mpu_cm@300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -984,6 +1107,7 @@
 
 		mpu_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -991,6 +1115,7 @@
 
 	dsp_cm: dsp_cm@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dsp_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -998,6 +1123,7 @@
 
 		dsp_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dsp_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1005,6 +1131,7 @@
 
 	abe_cm: abe_cm@500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "abe_cm";
 		reg = <0x500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1012,6 +1139,7 @@
 
 		abe_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "abe_clkctrl";
 			reg = <0x20 0x64>;
 			#clock-cells = <2>;
 		};
@@ -1022,6 +1150,7 @@
 &cm_core {
 	l3main1_cm: l3main1_cm@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3main1_cm";
 		reg = <0x700 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1029,6 +1158,7 @@
 
 		l3main1_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3main1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1036,6 +1166,7 @@
 
 	l3main2_cm: l3main2_cm@800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3main2_cm";
 		reg = <0x800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1043,6 +1174,7 @@
 
 		l3main2_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3main2_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1050,6 +1182,7 @@
 
 	ipu_cm: ipu_cm@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ipu_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1057,6 +1190,7 @@
 
 		ipu_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1064,6 +1198,7 @@
 
 	dma_cm: dma_cm@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dma_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1071,6 +1206,7 @@
 
 		dma_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dma_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1078,6 +1214,7 @@
 
 	emif_cm: emif_cm@b00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "emif_cm";
 		reg = <0xb00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1085,6 +1222,7 @@
 
 		emif_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emif_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
@@ -1092,6 +1230,7 @@
 
 	l4cfg_cm: l4cfg_cm@d00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4cfg_cm";
 		reg = <0xd00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1099,6 +1238,7 @@
 
 		l4cfg_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4cfg_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
@@ -1106,6 +1246,7 @@
 
 	l3instr_cm: l3instr_cm@e00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3instr_cm";
 		reg = <0xe00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1113,27 +1254,38 @@
 
 		l3instr_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3instr_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4per_cm: l4per_cm@1000 {
+	l4per_cm: clock@1000 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4per_cm";
 		reg = <0x1000 0x200>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1000 0x200>;
 
-		l4per_clkctrl: clk@20 {
+		l4per_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per_clkctrl";
 			reg = <0x20 0x15c>;
 			#clock-cells = <2>;
 		};
+
+		l4sec_clkctrl: clock@1a0 {
+			compatible = "ti,clkctrl";
+			clock-output-names = "l4sec_clkctrl";
+			reg = <0x1a0 0x3c>;
+			#clock-cells = <2>;
+		};
 	};
 
 	dss_cm: dss_cm@1400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dss_cm";
 		reg = <0x1400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1141,6 +1293,7 @@
 
 		dss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dss_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1148,6 +1301,7 @@
 
 	gpu_cm: gpu_cm@1500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gpu_cm";
 		reg = <0x1500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1155,6 +1309,7 @@
 
 		gpu_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1162,6 +1317,7 @@
 
 	l3init_cm: l3init_cm@1600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3init_cm";
 		reg = <0x1600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1169,6 +1325,7 @@
 
 		l3init_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3init_clkctrl";
 			reg = <0x20 0xd4>;
 			#clock-cells = <2>;
 		};
@@ -1178,6 +1335,7 @@
 &prm {
 	wkupaon_cm: wkupaon_cm@1900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkupaon_cm";
 		reg = <0x1900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1185,6 +1343,7 @@
 
 		wkupaon_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "wkupaon_clkctrl";
 			reg = <0x20 0x5c>;
 			#clock-cells = <2>;
 		};
@@ -1195,6 +1354,7 @@
 	fref_xtal_ck: fref_xtal_ck {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "fref_xtal_ck";
 		clocks = <&sys_clkin>;
 		ti,bit-shift = <28>;
 		reg = <0x14>;
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/ti/omap/twl4030.dtsi
index 93e07c18781b..93e07c18781b 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/ti/omap/twl4030.dtsi
diff --git a/arch/arm/boot/dts/twl4030_omap3.dtsi b/arch/arm/boot/dts/ti/omap/twl4030_omap3.dtsi
index 683419d5c0e5..89433f251df0 100644
--- a/arch/arm/boot/dts/twl4030_omap3.dtsi
+++ b/arch/arm/boot/dts/ti/omap/twl4030_omap3.dtsi
@@ -14,7 +14,7 @@
 	 * to the SYS_NIRQ line on OMAP.  Therefore, configure the
 	 * defaults for the SYS_NIRQ pin here.
 	 */
-	twl4030_pins: pinmux_twl4030_pins {
+	twl4030_pins: twl4030-pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21e0, PIN_INPUT_PULLUP | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* sys_nirq.sys_nirq */
 		>;
@@ -28,7 +28,7 @@
  * sys_nvmode2 signaling.
  */
 &omap3_pmx_wkup {
-	twl4030_vpins: pinmux_twl4030_vpins {
+	twl4030_vpins: twl4030-vpins-pins {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a00, PIN_INPUT | MUX_MODE0)		/* i2c4_scl.i2c4_scl */
 			OMAP3_WKUP_IOPAD(0x2a02, PIN_INPUT | MUX_MODE0)		/* i2c4_sda.i2c4_sda */
diff --git a/arch/arm/boot/dts/twl6030.dtsi b/arch/arm/boot/dts/ti/omap/twl6030.dtsi
index 9d588cfaa5cb..9d588cfaa5cb 100644
--- a/arch/arm/boot/dts/twl6030.dtsi
+++ b/arch/arm/boot/dts/ti/omap/twl6030.dtsi
diff --git a/arch/arm/boot/dts/twl6030_omap4.dtsi b/arch/arm/boot/dts/ti/omap/twl6030_omap4.dtsi
index fc498d0bde8b..64e38c7c8be7 100644
--- a/arch/arm/boot/dts/twl6030_omap4.dtsi
+++ b/arch/arm/boot/dts/ti/omap/twl6030_omap4.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 &twl {
@@ -19,7 +19,7 @@
 };
 
 &omap4_pmx_wkup {
-	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
+	twl6030_wkup_pins: twl6030-wkup-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x054, PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
 		>;
@@ -27,7 +27,7 @@
 };
 
 &omap4_pmx_core {
-	twl6030_pins: pinmux_twl6030_pins {
+	twl6030_pins: twl6030-pins {
 		pinctrl-single,pins = <
 			OMAP4_IOPAD(0x19e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
 		>;
diff --git a/arch/arm/boot/dts/uniphier-support-card.dtsi b/arch/arm/boot/dts/uniphier-support-card.dtsi
deleted file mode 100644
index bf441c2eff79..000000000000
--- a/arch/arm/boot/dts/uniphier-support-card.dtsi
+++ /dev/null
@@ -1,33 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-//
-// Device Tree Source for UniPhier Support Card (Expansion Board)
-//
-// Copyright (C) 2015-2017 Socionext Inc.
-//   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
-
-&system_bus {
-	status = "okay";
-	ranges = <1 0x00000000 0x42000000 0x02000000>;
-
-	support_card: support-card@1,1f00000 {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x00000000 1 0x01f00000 0x00100000>;
-		interrupt-parent = <&gpio>;
-
-		ethsc: ethernet@0 {
-			compatible = "smsc,lan9118", "smsc,lan9115";
-			reg = <0x00000000 0x1000>;
-			phy-mode = "mii";
-			reg-io-width = <4>;
-		};
-
-		serialsc: uart@b0000 {
-			compatible = "ns16550a";
-			reg = <0x000b0000 0x20>;
-			clock-frequency = <12288000>;
-			reg-shift = <1>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/unisoc/Makefile b/arch/arm/boot/dts/unisoc/Makefile
new file mode 100644
index 000000000000..dba5cd874ee7
--- /dev/null
+++ b/arch/arm/boot/dts/unisoc/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_RDA) += \
+	rda8810pl-orangepi-2g-iot.dtb \
+	rda8810pl-orangepi-i96.dtb
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts b/arch/arm/boot/dts/unisoc/rda8810pl-orangepi-2g-iot.dts
index 98e34248ae80..98e34248ae80 100644
--- a/arch/arm/boot/dts/rda8810pl-orangepi-2g-iot.dts
+++ b/arch/arm/boot/dts/unisoc/rda8810pl-orangepi-2g-iot.dts
diff --git a/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts b/arch/arm/boot/dts/unisoc/rda8810pl-orangepi-i96.dts
index 728f76931b99..728f76931b99 100644
--- a/arch/arm/boot/dts/rda8810pl-orangepi-i96.dts
+++ b/arch/arm/boot/dts/unisoc/rda8810pl-orangepi-i96.dts
diff --git a/arch/arm/boot/dts/rda8810pl.dtsi b/arch/arm/boot/dts/unisoc/rda8810pl.dtsi
index f30d6ece49fb..f30d6ece49fb 100644
--- a/arch/arm/boot/dts/rda8810pl.dtsi
+++ b/arch/arm/boot/dts/unisoc/rda8810pl.dtsi
diff --git a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts b/arch/arm/boot/dts/vf500-colibri-eval-v3.dts
deleted file mode 100644
index 076998968fb5..000000000000
--- a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * Copyright 2014 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "vf500-colibri.dtsi"
-#include "vf-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri VF50 on Colibri Evaluation Board";
-	compatible = "toradex,vf500-colibri_vf50-on-eval", "toradex,vf500-colibri_vf50", "fsl,vf500";
-};
-
-&touchscreen {
-	vf50-ts-min-pressure = <200>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/vf500-colibri.dtsi
deleted file mode 100644
index 92255f8893ce..000000000000
--- a/arch/arm/boot/dts/vf500-colibri.dtsi
+++ /dev/null
@@ -1,105 +0,0 @@
-/*
- * Copyright 2014 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "vf500.dtsi"
-#include "vf-colibri.dtsi"
-
-/ {
-	model = "Toradex Colibri VF50 COM";
-	compatible = "toradex,vf500-colibri_vf50", "fsl,vf500";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x8000000>;
-	};
-
-	touchscreen: vf50-touchscreen {
-		compatible = "toradex,vf50-touchscreen";
-		io-channels = <&adc1 0>,<&adc0 0>,
-				<&adc0 1>,<&adc1 2>;
-		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
-		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
-		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
-		pinctrl-names = "idle","default","gpios";
-		pinctrl-0 = <&pinctrl_touchctrl_idle>;
-		pinctrl-1 = <&pinctrl_touchctrl_default>;
-		pinctrl-2 = <&pinctrl_touchctrl_gpios>;
-		vf50-ts-min-pressure = <200>;
-		status = "disabled";
-	};
-};
-
-&nfc {
-	assigned-clocks = <&clks VF610_CLK_NFC>;
-	assigned-clock-rates = <33000000>;
-};
-
-&iomuxc {
-	vf610-colibri {
-		pinctrl_touchctrl_idle: touchctrl_idle {
-			fsl,pins = <
-				VF610_PAD_PTA18__GPIO_8		0x006d
-				VF610_PAD_PTA19__GPIO_9		0x006c
-				>;
-		};
-
-		pinctrl_touchctrl_default: touchctrl_default {
-			fsl,pins = <
-				VF610_PAD_PTA18__ADC0_SE0	0x0040
-				VF610_PAD_PTA19__ADC0_SE1	0x0040
-				VF610_PAD_PTA16__ADC1_SE0	0x0040
-				VF610_PAD_PTB2__ADC1_SE2	0x0040
-				>;
-		};
-
-		pinctrl_touchctrl_gpios: touchctrl_gpios {
-			fsl,pins = <
-				VF610_PAD_PTA23__GPIO_13	0x22e9
-				VF610_PAD_PTB23__GPIO_93	0x22e9
-				VF610_PAD_PTA22__GPIO_12	0x22e9
-				VF610_PAD_PTA11__GPIO_4		0x22e9
-				>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/vf610-colibri.dtsi b/arch/arm/boot/dts/vf610-colibri.dtsi
deleted file mode 100644
index 05c9a39509b8..000000000000
--- a/arch/arm/boot/dts/vf610-colibri.dtsi
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright 2014 Toradex AG
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "vf610.dtsi"
-#include "vf-colibri.dtsi"
-
-/ {
-	model = "Toradex Colibri VF61 COM";
-	compatible = "toradex,vf610-colibri_vf61", "fsl,vf610";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>;
-	};
-};
-
-&nfc {
-	assigned-clocks = <&clks VF610_CLK_NFC>;
-	assigned-clock-rates = <50000000>;
-};
diff --git a/arch/arm/boot/dts/vt8500/Makefile b/arch/arm/boot/dts/vt8500/Makefile
new file mode 100644
index 000000000000..255f4403af91
--- /dev/null
+++ b/arch/arm/boot/dts/vt8500/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_VT8500) += \
+	vt8500-bv07.dtb \
+	wm8505-ref.dtb \
+	wm8650-mid.dtb \
+	wm8750-apc8750.dtb \
+	wm8850-w70v2.dtb
diff --git a/arch/arm/boot/dts/vt8500-bv07.dts b/arch/arm/boot/dts/vt8500/vt8500-bv07.dts
index e9f55bd30bd4..e9f55bd30bd4 100644
--- a/arch/arm/boot/dts/vt8500-bv07.dts
+++ b/arch/arm/boot/dts/vt8500/vt8500-bv07.dts
diff --git a/arch/arm/boot/dts/vt8500.dtsi b/arch/arm/boot/dts/vt8500/vt8500.dtsi
index b7e09eff5bb2..b7e09eff5bb2 100644
--- a/arch/arm/boot/dts/vt8500.dtsi
+++ b/arch/arm/boot/dts/vt8500/vt8500.dtsi
diff --git a/arch/arm/boot/dts/wm8505-ref.dts b/arch/arm/boot/dts/vt8500/wm8505-ref.dts
index 2d77c087676e..2d77c087676e 100644
--- a/arch/arm/boot/dts/wm8505-ref.dts
+++ b/arch/arm/boot/dts/vt8500/wm8505-ref.dts
diff --git a/arch/arm/boot/dts/wm8505.dtsi b/arch/arm/boot/dts/vt8500/wm8505.dtsi
index 168cd12b07bc..168cd12b07bc 100644
--- a/arch/arm/boot/dts/wm8505.dtsi
+++ b/arch/arm/boot/dts/vt8500/wm8505.dtsi
diff --git a/arch/arm/boot/dts/wm8650-mid.dts b/arch/arm/boot/dts/vt8500/wm8650-mid.dts
index f6a42149a0a0..f6a42149a0a0 100644
--- a/arch/arm/boot/dts/wm8650-mid.dts
+++ b/arch/arm/boot/dts/vt8500/wm8650-mid.dts
diff --git a/arch/arm/boot/dts/wm8650.dtsi b/arch/arm/boot/dts/vt8500/wm8650.dtsi
index bc057b6f7d16..bc057b6f7d16 100644
--- a/arch/arm/boot/dts/wm8650.dtsi
+++ b/arch/arm/boot/dts/vt8500/wm8650.dtsi
diff --git a/arch/arm/boot/dts/wm8750-apc8750.dts b/arch/arm/boot/dts/vt8500/wm8750-apc8750.dts
index 136e812bc1e4..136e812bc1e4 100644
--- a/arch/arm/boot/dts/wm8750-apc8750.dts
+++ b/arch/arm/boot/dts/vt8500/wm8750-apc8750.dts
diff --git a/arch/arm/boot/dts/wm8750.dtsi b/arch/arm/boot/dts/vt8500/wm8750.dtsi
index 33aeb37491f4..33aeb37491f4 100644
--- a/arch/arm/boot/dts/wm8750.dtsi
+++ b/arch/arm/boot/dts/vt8500/wm8750.dtsi
diff --git a/arch/arm/boot/dts/wm8850-w70v2.dts b/arch/arm/boot/dts/vt8500/wm8850-w70v2.dts
index c7a6fe0ce48f..c7a6fe0ce48f 100644
--- a/arch/arm/boot/dts/wm8850-w70v2.dts
+++ b/arch/arm/boot/dts/vt8500/wm8850-w70v2.dts
diff --git a/arch/arm/boot/dts/wm8850.dtsi b/arch/arm/boot/dts/vt8500/wm8850.dtsi
index 65c9271050e6..65c9271050e6 100644
--- a/arch/arm/boot/dts/wm8850.dtsi
+++ b/arch/arm/boot/dts/vt8500/wm8850.dtsi
diff --git a/arch/arm/boot/dts/xen/Makefile b/arch/arm/boot/dts/xen/Makefile
new file mode 100644
index 000000000000..26c50f138952
--- /dev/null
+++ b/arch/arm/boot/dts/xen/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_VIRT) += \
+	xenvm-4.2.dtb
diff --git a/arch/arm/boot/dts/xenvm-4.2.dts b/arch/arm/boot/dts/xen/xenvm-4.2.dts
index 384cd92f1f84..384cd92f1f84 100644
--- a/arch/arm/boot/dts/xenvm-4.2.dts
+++ b/arch/arm/boot/dts/xen/xenvm-4.2.dts
diff --git a/arch/arm/boot/dts/xilinx/Makefile b/arch/arm/boot/dts/xilinx/Makefile
new file mode 100644
index 000000000000..9233e539b192
--- /dev/null
+++ b/arch/arm/boot/dts/xilinx/Makefile
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ZYNQ) += \
+	zynq-cc108.dtb \
+	zynq-ebaz4205.dtb \
+	zynq-microzed.dtb \
+	zynq-parallella.dtb \
+	zynq-zc702.dtb \
+	zynq-zc706.dtb \
+	zynq-zc770-xm010.dtb \
+	zynq-zc770-xm011.dtb \
+	zynq-zc770-xm012.dtb \
+	zynq-zc770-xm013.dtb \
+	zynq-zed.dtb \
+	zynq-zturn.dtb \
+	zynq-zturn-v5.dtb \
+	zynq-zybo.dtb \
+	zynq-zybo-z7.dtb
diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/xilinx/zynq-7000.dtsi
index ca6425ad794c..a7db3f3009f2 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/xilinx/zynq-7000.dtsi
@@ -59,7 +59,40 @@
 		regulator-always-on;
 	};
 
-	amba: amba {
+	replicator {
+		compatible = "arm,coresight-static-replicator";
+		clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+		clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+
+		out-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* replicator output ports */
+			port@0 {
+				reg = <0>;
+				replicator_out_port0: endpoint {
+					remote-endpoint = <&tpiu_in_port>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				replicator_out_port1: endpoint {
+					remote-endpoint = <&etb_in_port>;
+				};
+			};
+		};
+		in-ports {
+			/* replicator input port */
+			port {
+				replicator_in_port0: endpoint {
+					remote-endpoint = <&funnel_out_port>;
+				};
+			};
+		};
+	};
+
+	amba: axi {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -116,6 +149,7 @@
 			clocks = <&clkc 38>;
 			interrupt-parent = <&intc>;
 			interrupts = <0 25 4>;
+			clock-frequency = <400000>;
 			reg = <0xe0004000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -127,6 +161,7 @@
 			clocks = <&clkc 39>;
 			interrupt-parent = <&intc>;
 			interrupts = <0 48 4>;
+			clock-frequency = <400000>;
 			reg = <0xe0005000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -197,8 +232,20 @@
 			#size-cells = <0>;
 		};
 
+		qspi: spi@e000d000 {
+			compatible = "xlnx,zynq-qspi-1.0";
+			reg = <0xe000d000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 19 4>;
+			clocks = <&clkc 10>, <&clkc 43>;
+			clock-names = "ref_clk", "pclk";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		gem0: ethernet@e000b000 {
-			compatible = "cdns,zynq-gem", "cdns,gem";
+			compatible = "xlnx,zynq-gem", "cdns,gem";
 			reg = <0xe000b000 0x1000>;
 			status = "disabled";
 			interrupts = <0 22 4>;
@@ -209,7 +256,7 @@
 		};
 
 		gem1: ethernet@e000c000 {
-			compatible = "cdns,zynq-gem", "cdns,gem";
+			compatible = "xlnx,zynq-gem", "cdns,gem";
 			reg = <0xe000c000 0x1000>;
 			status = "disabled";
 			interrupts = <0 45 4>;
@@ -219,6 +266,27 @@
 			#size-cells = <0>;
 		};
 
+		smcc: memory-controller@e000e000 {
+			compatible = "arm,pl353-smc-r2p1", "arm,primecell";
+			reg = <0xe000e000 0x0001000>;
+			status = "disabled";
+			clock-names = "memclk", "apb_pclk";
+			clocks = <&clkc 11>, <&clkc 44>;
+			ranges = <0x0 0x0 0xe1000000 0x1000000 /* Nand CS region */
+				  0x1 0x0 0xe2000000 0x2000000 /* SRAM/NOR CS0 region */
+				  0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */
+			#address-cells = <2>;
+			#size-cells = <1>;
+
+			nfc0: nand-controller@0,0 {
+				compatible = "arm,pl353-nand-r2p1";
+				reg = <0 0 0x1000000>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		sdhci0: mmc@e0100000 {
 			compatible = "arasan,sdhci-8.9a";
 			status = "disabled";
@@ -277,20 +345,20 @@
 			};
 		};
 
-		dmac_s: dmac@f8003000 {
+		dmac_s: dma-controller@f8003000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xf8003000 0x1000>;
 			interrupt-parent = <&intc>;
-			interrupt-names = "abort", "dma0", "dma1", "dma2", "dma3",
-				"dma4", "dma5", "dma6", "dma7";
+			/*
+			 * interrupt-names = "abort", "dma0", "dma1", "dma2", "dma3",
+			 * "dma4", "dma5", "dma6", "dma7";
+			 */
 			interrupts = <0 13 4>,
 			             <0 14 4>, <0 15 4>,
 			             <0 16 4>, <0 17 4>,
 			             <0 40 4>, <0 41 4>,
 			             <0 42 4>, <0 43 4>;
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <4>;
 			clocks = <&clkc 27>;
 			clock-names = "apb_pclk";
 		};
@@ -365,5 +433,107 @@
 			reg = <0xf8005000 0x1000>;
 			timeout-sec = <10>;
 		};
+
+		etb@f8801000 {
+			compatible = "arm,coresight-etb10", "arm,primecell";
+			reg = <0xf8801000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			in-ports {
+				port {
+					etb_in_port: endpoint {
+						remote-endpoint = <&replicator_out_port1>;
+					};
+				};
+			};
+		};
+
+		tpiu@f8803000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0xf8803000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			in-ports {
+				port {
+					tpiu_in_port: endpoint {
+						remote-endpoint = <&replicator_out_port0>;
+					};
+				};
+			};
+		};
+
+		funnel@f8804000 {
+			compatible = "arm,coresight-static-funnel", "arm,primecell";
+			reg = <0xf8804000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+
+			/* funnel output ports */
+			out-ports {
+				port {
+					funnel_out_port: endpoint {
+						remote-endpoint =
+							<&replicator_in_port0>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* funnel input ports */
+				port@0 {
+					reg = <0>;
+					funnel0_in_port0: endpoint {
+						remote-endpoint = <&ptm0_out_port>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					funnel0_in_port1: endpoint {
+						remote-endpoint = <&ptm1_out_port>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					funnel0_in_port2: endpoint {
+					};
+				};
+				/* The other input ports are not connect to anything */
+			};
+		};
+
+		ptm@f889c000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0xf889c000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			cpu = <&cpu0>;
+			out-ports {
+				port {
+					ptm0_out_port: endpoint {
+						remote-endpoint = <&funnel0_in_port0>;
+					};
+				};
+			};
+		};
+
+		ptm@f889d000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0xf889d000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			cpu = <&cpu1>;
+			out-ports {
+				port {
+					ptm1_out_port: endpoint {
+						remote-endpoint = <&funnel0_in_port1>;
+					};
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/zynq-cc108.dts b/arch/arm/boot/dts/xilinx/zynq-cc108.dts
index 8b9ab9bba23b..8b9ab9bba23b 100644
--- a/arch/arm/boot/dts/zynq-cc108.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-cc108.dts
diff --git a/arch/arm/boot/dts/xilinx/zynq-ebaz4205.dts b/arch/arm/boot/dts/xilinx/zynq-ebaz4205.dts
new file mode 100644
index 000000000000..53fa6dbfd8fd
--- /dev/null
+++ b/arch/arm/boot/dts/xilinx/zynq-ebaz4205.dts
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
+ */
+/dts-v1/;
+/include/ "zynq-7000.dtsi"
+
+/ {
+	model = "Ebang EBAZ4205";
+	compatible = "ebang,ebaz4205", "xlnx,zynq-7000";
+
+	aliases {
+		ethernet0 = &gem0;
+		serial0 = &uart1;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x10000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&clkc {
+	ps-clk-frequency = <33333333>;
+	fclk-enable = <8>;
+};
+
+&gem0 {
+	status = "okay";
+	phy-mode = "mii";
+	phy-handle = <&phy>;
+
+	/* PHY clock */
+	assigned-clocks = <&clkc 18>;
+	assigned-clock-rates = <25000000>;
+
+	phy: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
+&nfc0 {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+	};
+};
+
+&pinctrl0 {
+	pinctrl_gpio0_default: gpio0-default {
+		mux {
+			groups = "gpio0_20_grp", "gpio0_32_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_20_grp", "gpio0_32_grp";
+			io-standard = <3>;
+			slew-rate = <0>;
+		};
+
+		conf-pull-up {
+			pins = "MIO20", "MIO32";
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_2_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_2_grp";
+			io-standard = <3>;
+			slew-rate = <0>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "gpio0_34_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "gpio0_34_grp";
+			io-standard = <3>;
+			slew-rate = <0>;
+			bias-high-impedance;
+			bias-pull-up;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_4_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_4_grp";
+			io-standard = <3>;
+			slew-rate = <0>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+};
+
+&smcc {
+	status = "okay";
+};
+
+&sdhci0 {
+	status = "okay";
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
diff --git a/arch/arm/boot/dts/zynq-microzed.dts b/arch/arm/boot/dts/xilinx/zynq-microzed.dts
index 6ed84fb15902..6ed84fb15902 100644
--- a/arch/arm/boot/dts/zynq-microzed.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-microzed.dts
diff --git a/arch/arm/boot/dts/zynq-parallella.dts b/arch/arm/boot/dts/xilinx/zynq-parallella.dts
index 54592aeb92b9..54592aeb92b9 100644
--- a/arch/arm/boot/dts/zynq-parallella.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-parallella.dts
diff --git a/arch/arm/boot/dts/zynq-zc702.dts b/arch/arm/boot/dts/xilinx/zynq-zc702.dts
index 27cd6cb52f1b..6efdbca9d3ef 100644
--- a/arch/arm/boot/dts/zynq-zc702.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc702.dts
@@ -5,6 +5,7 @@
  */
 /dts-v1/;
 #include "zynq-7000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Xilinx ZC702 board";
@@ -30,14 +31,14 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		sw14 {
+		switch-14 {
 			label = "sw14";
 			gpios = <&gpio0 12 0>;
 			linux,code = <108>; /* down */
 			wakeup-source;
 			autorepeat;
 		};
-		sw13 {
+		switch-13 {
 			label = "sw13";
 			gpios = <&gpio0 14 0>;
 			linux,code = <103>; /* up */
@@ -49,7 +50,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ds23 {
+		led-ds23 {
 			label = "ds23";
 			gpios = <&gpio0 10 0>;
 			linux,default-trigger = "heartbeat";
@@ -66,6 +67,12 @@
 	ocm: sram@fffc0000 {
 		compatible = "mmio-sram";
 		reg = <0xfffc0000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffc0000 0x10000>;
+		ocm-sram@0 {
+			reg = <0x0 0x10000>;
+		};
 	};
 };
 
@@ -100,8 +107,11 @@
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio0 50 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio0 51 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 
 	i2c-mux@74 {
 		compatible = "nxp,pca9548";
@@ -292,6 +302,19 @@
 		};
 	};
 
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_50_grp", "gpio0_51_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_50_grp", "gpio0_51_grp";
+			slew-rate = <0>;
+			io-standard = <1>;
+		};
+	};
+
 	pinctrl_sdhci0_default: sdhci0-default {
 		mux {
 			groups = "sdio0_2_grp";
diff --git a/arch/arm/boot/dts/zynq-zc706.dts b/arch/arm/boot/dts/xilinx/zynq-zc706.dts
index 77943c16d33f..77943c16d33f 100644
--- a/arch/arm/boot/dts/zynq-zc706.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc706.dts
diff --git a/arch/arm/boot/dts/zynq-zc770-xm010.dts b/arch/arm/boot/dts/xilinx/zynq-zc770-xm010.dts
index 0dd352289a45..0dd352289a45 100644
--- a/arch/arm/boot/dts/zynq-zc770-xm010.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc770-xm010.dts
diff --git a/arch/arm/boot/dts/zynq-zc770-xm011.dts b/arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts
index b7f65862c022..56732e8f6ca1 100644
--- a/arch/arm/boot/dts/zynq-zc770-xm011.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Xilinx ZC770 XM013 board DTS
+ * Xilinx ZC770 XM011 board DTS
  *
  * Copyright (C) 2013-2018 Xilinx, Inc.
  */
diff --git a/arch/arm/boot/dts/zynq-zc770-xm012.dts b/arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts
index d2359b789eb8..d2359b789eb8 100644
--- a/arch/arm/boot/dts/zynq-zc770-xm012.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts
diff --git a/arch/arm/boot/dts/zynq-zc770-xm013.dts b/arch/arm/boot/dts/xilinx/zynq-zc770-xm013.dts
index 4ae2c85df3a0..38d96adc870c 100644
--- a/arch/arm/boot/dts/zynq-zc770-xm013.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc770-xm013.dts
@@ -63,13 +63,12 @@
 	num-cs = <4>;
 	is-decoded-cs = <0>;
 	eeprom: eeprom@2 {
-		at25,byte-len = <8192>;
-		at25,addr-mode = <2>;
-		at25,page-size = <32>;
-
 		compatible = "atmel,at25";
 		reg = <2>;
 		spi-max-frequency = <1000000>;
+		size = <8192>;
+		address-width = <16>;
+		pagesize = <32>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/zynq-zed.dts b/arch/arm/boot/dts/xilinx/zynq-zed.dts
index 6a5a93aa6552..6a5a93aa6552 100644
--- a/arch/arm/boot/dts/zynq-zed.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zed.dts
diff --git a/arch/arm/boot/dts/zynq-zturn.dts b/arch/arm/boot/dts/xilinx/zynq-zturn-common.dtsi
index 5ec616ebca08..dfb1fbafe3aa 100644
--- a/arch/arm/boot/dts/zynq-zturn.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zturn-common.dtsi
@@ -13,8 +13,7 @@
 /include/ "zynq-7000.dtsi"
 
 / {
-	model = "Zynq Z-Turn MYIR Board";
-	compatible = "myir,zynq-zturn", "xlnx,zynq-7000";
+	compatible = "xlnx,zynq-7000";
 
 	aliases {
 		ethernet0 = &gem0;
@@ -50,7 +49,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		K1 {
+		key {
 			label = "K1";
 			gpios = <&gpio0 0x32 0x1>;
 			linux,code = <0x66>;
@@ -70,7 +69,6 @@
 	phy-handle = <&ethernet_phy>;
 
 	ethernet_phy: ethernet-phy@0 {
-		reg = <0x0>;
 	};
 };
 
@@ -106,7 +104,7 @@
 	};
 
 	accelerometer@53 {
-		compatible = "adi,adxl345", "adxl345", "adi,adxl34x", "adxl34x";
+		compatible = "adi,adxl345";
 		reg = <0x53>;
 		interrupt-parent = <&intc>;
 		interrupts = <0x0 0x1e 0x4>;
diff --git a/arch/arm/boot/dts/xilinx/zynq-zturn-v5.dts b/arch/arm/boot/dts/xilinx/zynq-zturn-v5.dts
new file mode 100644
index 000000000000..536632a09a25
--- /dev/null
+++ b/arch/arm/boot/dts/xilinx/zynq-zturn-v5.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+/include/ "zynq-zturn-common.dtsi"
+
+/ {
+	model = "Zynq Z-Turn MYIR Board V5";
+	compatible = "myir,zynq-zturn-v5", "xlnx,zynq-7000";
+};
+
+&gem0 {
+	ethernet_phy: ethernet-phy@0 {
+		reg = <0x3>;
+	};
+};
diff --git a/arch/arm/boot/dts/xilinx/zynq-zturn.dts b/arch/arm/boot/dts/xilinx/zynq-zturn.dts
new file mode 100644
index 000000000000..620b24a25e06
--- /dev/null
+++ b/arch/arm/boot/dts/xilinx/zynq-zturn.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+/include/ "zynq-zturn-common.dtsi"
+
+/ {
+	model = "Zynq Z-Turn MYIR Board";
+	compatible = "myir,zynq-zturn", "xlnx,zynq-7000";
+};
+
+&gem0 {
+	ethernet_phy: ethernet-phy@0 {
+		reg = <0x0>;
+	};
+};
diff --git a/arch/arm/boot/dts/zynq-zybo-z7.dts b/arch/arm/boot/dts/xilinx/zynq-zybo-z7.dts
index 357b78a5c11b..7b87e10d3953 100644
--- a/arch/arm/boot/dts/zynq-zybo-z7.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zybo-z7.dts
@@ -25,7 +25,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		ld4 {
+		led-ld4 {
 			label = "zynq-zybo-z7:green:ld4";
 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/zynq-zybo.dts b/arch/arm/boot/dts/xilinx/zynq-zybo.dts
index 755f6f109d5a..755f6f109d5a 100644
--- a/arch/arm/boot/dts/zynq-zybo.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zybo.dts
diff --git a/arch/arm/boot/dts/zx296702-ad1.dts b/arch/arm/boot/dts/zx296702-ad1.dts
deleted file mode 100644
index bd9400840023..000000000000
--- a/arch/arm/boot/dts/zx296702-ad1.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-/dts-v1/;
-
-#include "zx296702.dtsi"
-
-/ {
-	model = "ZTE ZX296702 AD1 Board";
-	compatible = "zte,zx296702-ad1", "zte,zx296702";
-
-	aliases {
-		serial0 = &uart0;
-		serial1 = &uart1;
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x50000000 0x20000000>;
-	};
-};
-
-&mmc0 {
-	supports-highspeed;
-	non-removable;
-	disable-wp;
-	status = "okay";
-
-	slot@0 {
-		reg = <0>;
-		bus-width = <4>;
-	};
-};
-
-&mmc1 {
-	supports-highspeed;
-	non-removable;
-	disable-wp;
-	status = "okay";
-
-	slot@0 {
-		reg = <0>;
-		bus-width = <8>;
-	};
-};
-
-&uart0 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/zx296702.dtsi b/arch/arm/boot/dts/zx296702.dtsi
deleted file mode 100644
index afd98de029be..000000000000
--- a/arch/arm/boot/dts/zx296702.dtsi
+++ /dev/null
@@ -1,142 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-#include <dt-bindings/clock/zx296702-clock.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		enable-method = "zte,zx296702-smp";
-
-		cpu@0 {
-			compatible = "arm,cortex-a9";
-			device_type = "cpu";
-			next-level-cache = <&l2cc>;
-			reg = <0>;
-		};
-
-		cpu@1 {
-			compatible = "arm,cortex-a9";
-			device_type = "cpu";
-			next-level-cache = <&l2cc>;
-			reg = <1>;
-		};
-	};
-
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		interrupt-parent = <&intc>;
-		ranges;
-
-		matrix: bus-matrix@400000 {
-			compatible = "zte,zx-bus-matrix";
-			reg = <0x00400000 0x1000>;
-		};
-
-		intc: interrupt-controller@801000 {
-			compatible = "arm,cortex-a9-gic";
-			#interrupt-cells = <3>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			interrupt-controller;
-			reg = <0x00801000 0x1000>,
-			      <0x00800100 0x100>;
-		};
-
-		global_timer: timer@8000200 {
-			compatible = "arm,cortex-a9-global-timer";
-			reg = <0x00800200 0x20>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-parent = <&intc>;
-			clocks = <&topclk ZX296702_A9_PERIPHCLK>;
-		};
-
-		l2cc: l2-cache-controller@c00000 {
-			compatible = "arm,pl310-cache";
-			reg = <0x00c00000 0x1000>;
-			cache-unified;
-			cache-level = <2>;
-			arm,data-latency = <1 1 1>;
-			arm,tag-latency = <1 1 1>;
-			arm,double-linefill = <1>;
-			arm,double-linefill-incr = <0>;
-		};
-
-		pcu: pcu@a0008000 {
-			compatible = "zte,zx296702-pcu";
-			reg = <0xa0008000 0x1000>;
-		};
-
-		topclk: topclk@9800000 {
-			compatible = "zte,zx296702-topcrm-clk";
-			reg = <0x09800000 0x1000>;
-			#clock-cells = <1>;
-		};
-
-		lsp1clk: lsp1clk@9400000 {
-			compatible = "zte,zx296702-lsp1crpm-clk";
-			reg = <0x09400000 0x1000>;
-			#clock-cells = <1>;
-		};
-
-		lsp0clk: lsp0clk@b000000 {
-			compatible = "zte,zx296702-lsp0crpm-clk";
-			reg = <0x0b000000 0x1000>;
-			#clock-cells = <1>;
-		};
-
-		uart0: serial@9405000 {
-			compatible = "zte,zx296702-uart";
-			reg = <0x09405000 0x1000>;
-			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&lsp1clk ZX296702_UART0_WCLK>;
-			status = "disabled";
-		};
-
-		uart1: serial@9406000 {
-			compatible = "zte,zx296702-uart";
-			reg = <0x09406000 0x1000>;
-			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&lsp1clk ZX296702_UART1_WCLK>;
-			status = "disabled";
-		};
-
-		mmc0: mmc@9408000 {
-			compatible = "snps,dw-mshc";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x09408000 0x1000>;
-			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-			fifo-depth = <32>;
-			clocks = <&lsp1clk ZX296702_SDMMC0_PCLK>,
-				 <&lsp1clk ZX296702_SDMMC0_WCLK>;
-			clock-names = "biu", "ciu";
-			status = "disabled";
-		};
-
-		mmc1: mmc@b003000 {
-			compatible = "snps,dw-mshc";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0b003000 0x1000>;
-			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
-			fifo-depth = <32>;
-			clocks = <&lsp0clk ZX296702_SDMMC1_PCLK>,
-				 <&lsp0clk ZX296702_SDMMC1_WCLK>;
-			clock-names = "biu", "ciu";
-			status = "disabled";
-		};
-
-		sysctrl: sysctrl@a0007000 {
-			compatible = "zte,sysctrl", "syscon";
-			reg = <0xa0007000 0x1000>;
-		};
-	};
-};